41 CFR 102-74.340 - Who is responsible for monitoring and controlling areas designated for smoking by an agency head...

Code of Federal Regulations, 2014 CFR

2014-01-01

... with proper signage? 102-74.340 Section 102-74.340 Public Contracts and Property Management Federal... designated for smoking by an agency head and for identifying those areas with proper signage? Agency heads... smoking and identifying these areas with proper signage. Suitable, uniform signs reading “Designated...

41 CFR 102-74.340 - Who is responsible for monitoring and controlling areas designated for smoking by an agency head...

Code of Federal Regulations, 2012 CFR

2012-01-01

... with proper signage? 102-74.340 Section 102-74.340 Public Contracts and Property Management Federal... designated for smoking by an agency head and for identifying those areas with proper signage? Agency heads... smoking and identifying these areas with proper signage. Suitable, uniform signs reading “Designated...

Optical burst switching based satellite backbone network

NASA Astrophysics Data System (ADS)

Li, Tingting; Guo, Hongxiang; Wang, Cen; Wu, Jian

2018-02-01

We propose a novel time slot based optical burst switching (OBS) architecture for GEO/LEO based satellite backbone network. This architecture can provide high speed data transmission rate and high switching capacity . Furthermore, we design the control plane of this optical satellite backbone network. The software defined network (SDN) and network slice (NS) technologies are introduced. Under the properly designed control mechanism, this backbone network is flexible to support various services with diverse transmission requirements. Additionally, the LEO access and handoff management in this network is also discussed.

Diatomite filtration of water for injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olmsted, B.C. Jr.; Bell, G.R.

1966-01-01

A discussion is presented of the capabilities, problems, and answers, in the performance of diatomite filters. The discussion includes a description of diatomite filtration, new developments, design criteria, and some case histories. Diatomite filters, when properly designed and installed, and when properly applied, can provide effective clarification of waters for injection at low capital and operating costs. Design, installation, and proper application, effectiveness, and capital and operating costs can be placed in the proper perspective in the light of general experience and recent pilot plant tests in the southern California area. (30 refs.)

32 CFR 770.3 - Fishing regulations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 5 2011-07-01 2011-07-01 false Fishing regulations. 770.3 Section 770.3..., Virginia § 770.3 Fishing regulations. (a) All persons possessing the proper state license and Base permit are permitted to fish in the areas designated by the Annual Fishing Regulations on Marine Corps Base...

32 CFR 770.3 - Fishing regulations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Fishing regulations. 770.3 Section 770.3..., Virginia § 770.3 Fishing regulations. (a) All persons possessing the proper state license and Base permit are permitted to fish in the areas designated by the Annual Fishing Regulations on Marine Corps Base...

The Commander’s Emergency Response Program: A Model for Future Implementation

DTIC Science & Technology

2010-04-07

unintended Effects. The INVEST-E methodology serves as a tool for commanders and their designated practitioners to properly select projects, increasing...for commanders and their designated practitioners to properly select projects, increasing the effectiveness of CERP funds. 4 TABLE OF...and unintended Effects. The INVEST-E methodology serves as a tool for commanders and their designated practitioners to properly select projects

Design of tunable thermo-optic C-band filter based on coated silicon slab

NASA Astrophysics Data System (ADS)

Pinhas, Hadar; Malka, Dror; Danan, Yossef; Sinvani, Moshe; Zalevsky, Zeev

2018-03-01

Optical filters are required to have narrow band-pass filtering in the spectral C-band for applications such as signal tracking, sub-band filtering or noise suppression. These requirements lead to a variety of filters such as Mach-Zehnder interferometer inter-leaver in silica, which offer thermo-optic effect for optical switching, however, without proper thermal and optical efficiency. In this paper we propose tunable thermo-optic filtering device based on coated silicon slab resonator with increased Q-factor for the C-band optical switching. The device can be designed either for long range wavelength tuning of for short range with increased wavelength resolution. Theoretical examination of the thermal parameters affecting the filtering process is shown together with experimental results. Proper channel isolation with an extinction ratio of 20dBs is achieved with spectral bandpass width of 0.07nm.

Application of a territorial-based filtering algorithm in turbomachinery blade design optimization

NASA Astrophysics Data System (ADS)

Bahrami, Salman; Khelghatibana, Maryam; Tribes, Christophe; Yi Lo, Suk; von Fellenberg, Sven; Trépanier, Jean-Yves; Guibault, François

2017-02-01

A territorial-based filtering algorithm (TBFA) is proposed as an integration tool in a multi-level design optimization methodology. The design evaluation burden is split between low- and high-cost levels in order to properly balance the cost and required accuracy in different design stages, based on the characteristics and requirements of the case at hand. TBFA is in charge of connecting those levels by selecting a given number of geometrically different promising solutions from the low-cost level to be evaluated in the high-cost level. Two test case studies, a Francis runner and a transonic fan rotor, have demonstrated the robustness and functionality of TBFA in real industrial optimization problems.

Use of Problem-Based Learning in the Teaching and Learning of Horticultural Production

ERIC Educational Resources Information Center

Abbey, Lord; Dowsett, Eric; Sullivan, Jan

2017-01-01

Purpose: Problem-based learning (PBL), a relatively novel teaching and learning process in horticulture, was investigated. Proper application of PBL can potentially create a learning context that enhances student learning. Design/Methodology/Approach: Students worked on two complex ill-structured problems: (1) to produce fresh baby greens for a…

40 CFR 745.83 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... with the manufacturer's instructions. Interim controls means a set of measures designed to temporarily... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED... disposable cleaning cloths with the card, whether post-renovation cleaning has been properly completed...

40 CFR 745.83 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... with the manufacturer's instructions. Interim controls means a set of measures designed to temporarily... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED... disposable cleaning cloths with the card, whether post-renovation cleaning has been properly completed...

40 CFR 745.83 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... with the manufacturer's instructions. Interim controls means a set of measures designed to temporarily... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED... disposable cleaning cloths with the card, whether post-renovation cleaning has been properly completed...

15 CFR 1.2 - Description and design.

Code of Federal Regulations, 2010 CFR

2010-01-01

... fesse azure and or, a ship in full sail on waves of the sea, in chief proper; and in base a lighthouse... issued with the President's approval of the seal, made necessary by changes in the functions of the...

Repair, Evaluation, Maintenance, and Rehabilitation Research Program. Lubricants for Hydraulic Structures

DTIC Science & Technology

1989-08-01

machinery design , precision machining, proper maintenance, and proper lubrication. Ordinarily, wear is thought of only in terms of abrasive wear occurring in...operate under this principle. However, the design must allow the plates to lift and tilt properly and provide sufficient area to lift the load. 38. Another...friction and wear to a minimum. Boundary Lubrication 42. Lubrication designed to protect against frictional effects when asperities meet is called

The Effects of Different Interaction Types in Web-Based Teaching on the Attitudes of Learners towards Web-Based Teaching and Internet

ERIC Educational Resources Information Center

Turkish Online Journal of Distance Education, 2013

2013-01-01

It might be said that attitudes impact success directly in web-based teaching and timely and appropriate fulfillment of learners' expectations bear utmost significance for their success. From this perspective a properly designed web supported teaching application can provide positive contribution as well to learners' attitudes towards web…

Classification of urine sediment based on convolution neural network

NASA Astrophysics Data System (ADS)

Pan, Jingjing; Jiang, Cunbo; Zhu, Tiantian

2018-04-01

By designing a new convolution neural network framework, this paper breaks the constraints of the original convolution neural network framework requiring large training samples and samples of the same size. Move and cropping the input images, generate the same size of the sub-graph. And then, the generated sub-graph uses the method of dropout, increasing the diversity of samples and preventing the fitting generation. Randomly select some proper subset in the sub-graphic set and ensure that the number of elements in the proper subset is same and the proper subset is not the same. The proper subsets are used as input layers for the convolution neural network. Through the convolution layer, the pooling, the full connection layer and output layer, we can obtained the classification loss rate of test set and training set. In the red blood cells, white blood cells, calcium oxalate crystallization classification experiment, the classification accuracy rate of 97% or more.

Design and development of Hoeken's structural dynamic linkage based agro-tiller machine

NASA Astrophysics Data System (ADS)

Hynes, N. Rajesh Jesudoss; Saran, K.; Pavithran, V.

2018-05-01

India is one of biggest exporters of medicinal plants, spices and other many agro products in the world. Owing to the special needs, an agricultural machine is designed using Hoeken linkage with Pantograph mechanism and developed that ensures safety digging to uproot the plant. Thus, the focus is to cut the plant by machine with proper care and shoot system is cut properly avoiding any damage to the upper part of the plant and rather be cut in the root area to use it. This is done by the agricultural cutting machine by the name "agricultural tiller machine" that can perform the action same as the objective needed for the effective production of raw materials for manufacturing of the agro products.

A Method for Computing Leading-Edge Loads

NASA Technical Reports Server (NTRS)

Rhode, Richard V; Pearson, Henry A

1933-01-01

In this report a formula is developed that enables the determination of the proper design load for the portion of the wing forward of the front spar. The formula is inherently rational in concept, as it takes into account the most important variables that affect the leading-edge load, although theoretical rigor has been sacrificed for simplicity and ease of application. Some empirical corrections, based on pressure distribution measurements on the PW-9 and M-3 airplanes have been introduced to provide properly for biplanes. Results from the formula check experimental values in a variety of cases with good accuracy in the critical loading conditions. The use of the method for design purposes is therefore felt to be justified and is recommended.

Three CLIPS-based expert systems for solving engineering problems

NASA Technical Reports Server (NTRS)

Parkinson, W. J.; Luger, G. F.; Bretz, R. E.

1990-01-01

We have written three expert systems, using the CLIPS PC-based expert system shell. These three expert systems are rule based and are relatively small, with the largest containing slightly less than 200 rules. The first expert system is an expert assistant that was written to help users of the ASPEN computer code choose the proper thermodynamic package to use with their particular vapor-liquid equilibrium problem. The second expert system was designed to help petroleum engineers choose the proper enhanced oil recovery method to be used with a given reservoir. The effectiveness of each technique is highly dependent upon the reservoir conditions. The third expert system is a combination consultant and control system. This system was designed specifically for silicon carbide whisker growth. Silicon carbide whiskers are an extremely strong product used to make ceramic and metal composites. The manufacture of whiskers is a very complicated process. which to date. has defied a good mathematical model. The process was run by experts who had gained their expertise by trial and error. A system of rules was devised by these experts both for procedure setup and for the process control. In this paper we discuss the three problem areas of the design, development and evaluation of the CLIPS-based programs.

Statistical inference for extended or shortened phase II studies based on Simon's two-stage designs.

PubMed

Zhao, Junjun; Yu, Menggang; Feng, Xi-Ping

2015-06-07

Simon's two-stage designs are popular choices for conducting phase II clinical trials, especially in the oncology trials to reduce the number of patients placed on ineffective experimental therapies. Recently Koyama and Chen (2008) discussed how to conduct proper inference for such studies because they found that inference procedures used with Simon's designs almost always ignore the actual sampling plan used. In particular, they proposed an inference method for studies when the actual second stage sample sizes differ from planned ones. We consider an alternative inference method based on likelihood ratio. In particular, we order permissible sample paths under Simon's two-stage designs using their corresponding conditional likelihood. In this way, we can calculate p-values using the common definition: the probability of obtaining a test statistic value at least as extreme as that observed under the null hypothesis. In addition to providing inference for a couple of scenarios where Koyama and Chen's method can be difficult to apply, the resulting estimate based on our method appears to have certain advantage in terms of inference properties in many numerical simulations. It generally led to smaller biases and narrower confidence intervals while maintaining similar coverages. We also illustrated the two methods in a real data setting. Inference procedures used with Simon's designs almost always ignore the actual sampling plan. Reported P-values, point estimates and confidence intervals for the response rate are not usually adjusted for the design's adaptiveness. Proper statistical inference procedures should be used.

Case history : use of Tenax and Tensar geogrids for base course stabilization : technical assistance report.

DOT National Transportation Integrated Search

1999-01-01

Geogrids can be used successfully for subgrade stabilization under permanent pavements. To be successful, proper designs incorporating existing soil conditions and anticipated loading need to be performed. subgrade soil strength should be determined ...

Physical models and primary design of reactor based slow positron source at CMRR

NASA Astrophysics Data System (ADS)

Wang, Guanbo; Li, Rundong; Qian, Dazhi; Yang, Xin

2018-07-01

Slow positron facilities are widely used in material science. A high intensity slow positron source is now at the design stage based on the China Mianyang Research Reactor (CMRR). This paper describes the physical models and our primary design. We use different computer programs or mathematical formula to simulate different physical process, and validate them by proper experiments. Considering the feasibility, we propose a primary design, containing a cadmium shield, a honeycomb arranged W tubes assembly, electrical lenses, and a solenoid. It is planned to be vertically inserted in the Si-doping channel. And the beam intensity is expected to be 5 ×109

40 CFR 745.83 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... with none of the air leaking past it. Interim controls means a set of measures designed to temporarily... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED... disposable cleaning cloths with the card, whether post-renovation cleaning has been properly completed...

40 CFR 745.83 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... with none of the air leaking past it. Interim controls means a set of measures designed to temporarily... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED... disposable cleaning cloths with the card, whether post-renovation cleaning has been properly completed...

CONTROLLING STORM WATER RUNOFF WITH TRADABLE CREDITS FOR IMPERVIOUS SURFACES

EPA Science Inventory

Storm water flow off impervious surface in a watershed can lead to stream degradation, habitat alteration, low base flows and toxic leading. We show that a properly designed tradable runoff credit (TRC) system creates economic incentives for landowners to employ best management p...

Long-term attitude sustainability from a constructivist-based astronomy-for-teachers course

NASA Astrophysics Data System (ADS)

Slater, T. F.; Safko, J. L.; Carpenter, J. R.

Survey performed four years after in-service teachers (elementary and middle school) took a special astronomy course using constructivist approach. Attitudes and confidence toward teaching astronomy did not decline during this time, implying that properly designed courses have long-term effectiveness.

Influence of cross-phase modulation in SPM-based nonlinear optical loop mirror

NASA Astrophysics Data System (ADS)

Pitois, Stéphane

2005-09-01

We study the role of cross-phase modulation (CPM) occurring between the two counter-propagating parts of a signal wave in a standard SPM-based nonlinear optical fiber loop mirror (NOLM). For pulse train with high duty-cycle, we experimentally observe the influence of cross-phase modulation on NOLM transmittivity. Finally, we propose a solution based on properly designed dispersion imbalanced NOLM to overcome undesirable CPM effects.

Certainty Equivalence M-MRAC for Systems with Unmatched Uncertainties

NASA Technical Reports Server (NTRS)

Stepanyan, Vahram; Krishnakumar, Kalmanje

2012-01-01

The paper presents a certainty equivalence state feedback indirect adaptive control design method for the systems of any relative degree with unmatched uncertainties. The approach is based on the parameter identification (estimation) model, which is completely separated from the control design and is capable of producing parameter estimates as fast as the computing power allows without generating high frequency oscillations. It is shown that the system's input and output tracking errors can be systematically decreased by the proper choice of the design parameters.

Pendulum impact testing of an impact-breakaway, windresistant base connection for multi-post ground signs.

DOT National Transportation Integrated Search

2012-07-01

Roadside signs play an important role in traffic control systems and must be placed adjacent to roadways. If they are not designed, : fabricated, and installed properly, ground signs may pose potential hazards to vehicle passengers in the event of a ...

Pendulum impact testing of an impact-breakaway, windresistant base connection for multi-post ground signs : [summary].

DOT National Transportation Integrated Search

2012-01-01

Roadside signs are critical to traffic control. : However, if not properly designed to yield : upon vehicle impact, these signs become lifethreatening : hazards. Yet, the signs must be able : to withstand wind loading, in Florida, up to : hurricane f...

Terahertz bandwidth all-optical Hilbert transformers based on long-period gratings.

PubMed

Ashrafi, Reza; Azaña, José

2012-07-01

A novel, all-optical design for implementing terahertz (THz) bandwidth real-time Hilbert transformers is proposed and numerically demonstrated. An all-optical Hilbert transformer can be implemented using a uniform-period long-period grating (LPG) with a properly designed amplitude-only grating apodization profile, incorporating a single π-phase shift in the middle of the grating length. The designed LPG-based Hilbert transformers can be practically implemented using either fiber-optic or integrated-waveguide technologies. As a generalization, photonic fractional Hilbert transformers are also designed based on the same optical platform. In this general case, the resulting LPGs have multiple π-phase shifts along the grating length. Our numerical simulations confirm that all-optical Hilbert transformers capable of processing arbitrary optical signals with bandwidths well in the THz range can be implemented using feasible fiber/waveguide LPG designs.

Design-based stereology: Planning, volumetry and sampling are crucial steps for a successful study.

PubMed

Tschanz, Stefan; Schneider, Jan Philipp; Knudsen, Lars

2014-01-01

Quantitative data obtained by means of design-based stereology can add valuable information to studies performed on a diversity of organs, in particular when correlated to functional/physiological and biochemical data. Design-based stereology is based on a sound statistical background and can be used to generate accurate data which are in line with principles of good laboratory practice. In addition, by adjusting the study design an appropriate precision can be achieved to find relevant differences between groups. For the success of the stereological assessment detailed planning is necessary. In this review we focus on common pitfalls encountered during stereological assessment. An exemplary workflow is included, and based on authentic examples, we illustrate a number of sampling principles which can be implemented to obtain properly sampled tissue blocks for various purposes. Copyright © 2013 Elsevier GmbH. All rights reserved.

Water supply pipe dimensioning using hydraulic power dissipation

NASA Astrophysics Data System (ADS)

Sreemathy, J. R.; Rashmi, G.; Suribabu, C. R.

2017-07-01

Proper sizing of the pipe component of water distribution networks play an important role in the overall design of the any water supply system. Several approaches have been applied for the design of networks from an economical point of view. Traditional optimization techniques and population based stochastic algorithms are widely used to optimize the networks. But the use of these approaches is mostly found to be limited to the research level due to difficulties in understanding by the practicing engineers, design engineers and consulting firms. More over due to non-availability of commercial software related to the optimal design of water distribution system,it forces the practicing engineers to adopt either trial and error or experience-based design. This paper presents a simple approach based on power dissipation in each pipeline as a parameter to design the network economically, but not to the level of global minimum cost.

Optimal design of a beam-based dynamic vibration absorber using fixed-points theory

NASA Astrophysics Data System (ADS)

Hua, Yingyu; Wong, Waion; Cheng, Li

2018-05-01

The addition of a dynamic vibration absorber (DVA) to a vibrating structure could provide an economic solution for vibration suppressions if the absorber is properly designed and located onto the structure. A common design of the DVA is a sprung mass because of its simple structure and low cost. However, the vibration suppression performance of this kind of DVA is limited by the ratio between the absorber mass and the mass of the primary structure. In this paper, a beam-based DVA (beam DVA) is proposed and optimized for minimizing the resonant vibration of a general structure. The vibration suppression performance of the proposed beam DVA depends on the mass ratio, the flexural rigidity and length of the beam. In comparison with the traditional sprung mass DVA, the proposed beam DVA shows more flexibility in vibration control design because it has more design parameters. With proper design, the beam DVA's vibration suppression capability can outperform that of the traditional DVA under the same mass constraint. The general approach is illustrated using a benchmark cantilever beam as an example. The receptance theory is introduced to model the compound system consisting of the host beam and the attached beam-based DVA. The model is validated through comparisons with the results from Abaqus as well as the Transfer Matrix method (TMM) method. Fixed-points theory is then employed to derive the analytical expressions for the optimum tuning ratio and damping ratio of the proposed beam absorber. A design guideline is then presented to choose the parameters of the beam absorber. Comparisons are finally presented between the beam absorber and the traditional DVA in terms of the vibration suppression effect. It is shown that the proposed beam absorber can outperform the traditional DVA by following this proposed guideline.

Technological Minimalism: A Cost-Effective Alternative for Course Design and Development.

ERIC Educational Resources Information Center

Lorenzo, George

2001-01-01

Discusses the use of minimum levels of technology, or technological minimalism, for Web-based multimedia course content. Highlights include cost effectiveness; problems with video streaming, the use of XML for Web pages, and Flash and Java applets; listservs instead of proprietary software; and proper faculty training. (LRW)

Solving Quantitative Problems: Guidelines for Teaching Derived from Research.

ERIC Educational Resources Information Center

Kramers-Pals, H.; Pilot, A.

1988-01-01

Presents four guidelines for teaching quantitative problem-solving based on research results: analyze difficulties of students, develop a system of heuristics, select and map key relations, and design instruction with proper orientation, exercise, and feedback. Discusses the four guidelines and uses flow charts and diagrams to show how the…

Investigation of asphalt content design for open-graded bituminous mixes.

DOT National Transportation Integrated Search

1974-01-01

Several design procedures associated with determining the proper asphalt content for open-graded bituminous mixes were investigated. Also considered was the proper amount of tack coat that should be placed on the old surface prior to paving operation...

Design and simulation of a cable-pulley-based transmission for artificial ankle joints

NASA Astrophysics Data System (ADS)

Liu, Huaxin; Ceccarelli, Marco; Huang, Qiang

2016-06-01

In this paper, a mechanical transmission based on cable pulley is proposed for human-like actuation in the artificial ankle joints of human-scale. The anatomy articular characteristics of the human ankle is discussed for proper biomimetic inspiration in designing an accurate, efficient, and robust motion control of artificial ankle joint devices. The design procedure is presented through the inclusion of conceptual considerations and design details for an interactive solution of the transmission system. A mechanical design is elaborated for the ankle joint angular with pitch motion. A multi-body dynamic simulation model is elaborated accordingly and evaluated numerically in the ADAMS environment. Results of the numerical simulations are discussed to evaluate the dynamic performance of the proposed design solution and to investigate the feasibility of the proposed design in future applications for humanoid robots.

Computer aided design of architecture of degradable tissue engineering scaffolds.

PubMed

Heljak, M K; Kurzydlowski, K J; Swieszkowski, W

2017-11-01

One important factor affecting the process of tissue regeneration is scaffold stiffness loss, which should be properly balanced with the rate of tissue regeneration. The aim of the research reported here was to develop a computer tool for designing the architecture of biodegradable scaffolds fabricated by melt-dissolution deposition systems (e.g. Fused Deposition Modeling) to provide the required scaffold stiffness at each stage of degradation/regeneration. The original idea presented in the paper is that the stiffness of a tissue engineering scaffold can be controlled during degradation by means of a proper selection of the diameter of the constituent fibers and the distances between them. This idea is based on the size-effect on degradation of aliphatic polyesters. The presented computer tool combines a genetic algorithm and a diffusion-reaction model of polymer hydrolytic degradation. In particular, we show how to design the architecture of scaffolds made of poly(DL-lactide-co-glycolide) with the required Young's modulus change during hydrolytic degradation.

A quantitative analysis of statistical power identifies obesity endpoints for improved in vivo preclinical study design

PubMed Central

Selimkhanov, Jangir; Thompson, W. Clayton; Guo, Juen; Hall, Kevin D.; Musante, Cynthia J.

2017-01-01

The design of well-powered in vivo preclinical studies is a key element in building knowledge of disease physiology for the purpose of identifying and effectively testing potential anti-obesity drug targets. However, as a result of the complexity of the obese phenotype, there is limited understanding of the variability within and between study animals of macroscopic endpoints such as food intake and body composition. This, combined with limitations inherent in the measurement of certain endpoints, presents challenges to study design that can have significant consequences for an anti-obesity program. Here, we analyze a large, longitudinal study of mouse food intake and body composition during diet perturbation to quantify the variability and interaction of key metabolic endpoints. To demonstrate how conclusions can change as a function of study size, we show that a simulated pre-clinical study properly powered for one endpoint may lead to false conclusions based on secondary endpoints. We then propose guidelines for endpoint selection and study size estimation under different conditions to facilitate proper power calculation for a more successful in vivo study design. PMID:28392555

Ultra Low Power Datalogger

NASA Astrophysics Data System (ADS)

Holik, Michael

2010-01-01

The article describes a design and the test of the datalogger unit. Main demands on the datalogger were to achieve the power consumption as low as possible and the ability to capture short-time events. The datalogger is based on a programmable logic device FPGA. VHDL language is used to design the architecture fitted into the FPGA. The results of the test confirmed low power consumption feature of the device as well as proper functionality of the unit.

Review & Peer Review of “Parameters for Properly Designed and Operated Flares” Documents

EPA Pesticide Factsheets

This page contains two 2012 memoranda on the review of EPA's parameters for properly designed and operated flares. One details the process of peer review, and the other provides background information and specific charge questions to the panel.

Evaluation of a Web-based Error Reporting Surveillance System in a Large Iranian Hospital.

PubMed

Askarian, Mehrdad; Ghoreishi, Mahboobeh; Akbari Haghighinejad, Hourvash; Palenik, Charles John; Ghodsi, Maryam

2017-08-01

Proper reporting of medical errors helps healthcare providers learn from adverse incidents and improve patient safety. A well-designed and functioning confidential reporting system is an essential component to this process. There are many error reporting methods; however, web-based systems are often preferred because they can provide; comprehensive and more easily analyzed information. This study addresses the use of a web-based error reporting system. This interventional study involved the application of an in-house designed "voluntary web-based medical error reporting system." The system has been used since July 2014 in Nemazee Hospital, Shiraz University of Medical Sciences. The rate and severity of errors reported during the year prior and a year after system launch were compared. The slope of the error report trend line was steep during the first 12 months (B = 105.727, P = 0.00). However, it slowed following launch of the web-based reporting system and was no longer statistically significant (B = 15.27, P = 0.81) by the end of the second year. Most recorded errors were no-harm laboratory types and were due to inattention. Usually, they were reported by nurses and other permanent employees. Most reported errors occurred during morning shifts. Using a standardized web-based error reporting system can be beneficial. This study reports on the performance of an in-house designed reporting system, which appeared to properly detect and analyze medical errors. The system also generated follow-up reports in a timely and accurate manner. Detection of near-miss errors could play a significant role in identifying areas of system defects.

78 FR 40149 - Scientific Information Request on Chronic Urinary Retention (CUR) Treatment

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-03

... improve the quality of this review. AHRQ is conducting this comparative effectiveness review pursuant to..., study period, design, methodology, indication and diagnosis, proper use instructions, inclusion and... study number, the study period, design, methodology, indication and diagnosis, proper use instructions...

Design of vibration isolation systems using multiobjective optimization techniques

NASA Technical Reports Server (NTRS)

Rao, S. S.

1984-01-01

The design of vibration isolation systems is considered using multicriteria optimization techniques. The integrated values of the square of the force transmitted to the main mass and the square of the relative displacement between the main mass and the base are taken as the performance indices. The design of a three degrees-of-freedom isolation system with an exponentially decaying type of base disturbance is considered for illustration. Numerical results are obtained using the global criterion, utility function, bounded objective, lexicographic, goal programming, goal attainment and game theory methods. It is found that the game theory approach is superior in finding a better optimum solution with proper balance of the various objective functions.

Application of 3D printing to prototype and develop novel plant tissue culture systems.

PubMed

Shukla, Mukund R; Singh, Amritpal S; Piunno, Kevin; Saxena, Praveen K; Jones, A Maxwell P

2017-01-01

Due to the complex process of designing and manufacturing new plant tissue culture vessels through conventional means there have been limited efforts to innovate improved designs. Further, development and availability of low cost, energy efficient LEDs of various spectra has made it a promising light source for plant growth in controlled environments. However, direct replacement of conventional lighting sources with LEDs does not address problems with uniformity, spectral control, or the challenges in conducting statistically valid experiments to assess the effects of light. Prototyping using 3D printing and LED based light sources could help overcome these limitations and lead to improved culture systems. A modular culture vessel design in which the fluence rate and spectrum of light are independently controlled was designed, prototyped using 3D printing, and evaluated for plant growth. This design is compatible with semi-solid and liquid based culture systems. Observations on morphology, chlorophyll content, and chlorophyll fluorescence based stress parameters from in vitro plants cultured under different light spectra with similar overall fluence rate indicated different responses in Nicotiana tabacum and Artemisia annua plantlets. This experiment validates the utility of 3D printing to design and test functional vessels and demonstrated that optimal light spectra for in vitro plant growth is species-specific. 3D printing was successfully used to prototype novel culture vessels with independently controlled variable fluence rate/spectra LED lighting. This system addresses several limitations associated with current lighting systems, providing more uniform lighting and allowing proper replication/randomization for experimental plant biology while increasing energy efficiency. A complete procedure including the design and prototyping of a culture vessel using 3D printing, commercial scale injection molding of the prototype, and conducting a properly replicated experiment are discussed. This open source design has the scope for further improvement and adaptation and demonstrates the power of 3D printing to improve the design of culture systems.

On public space design for Chinese urban residential area based on integrated architectural physics environment evaluation

NASA Astrophysics Data System (ADS)

Dong, J. Y.; Cheng, W.; Ma, C. P.; Tan, Y. T.; Xin, L. S.

2017-04-01

The residential public space is an important part in designing the ecological residence, and a proper physics environment of public space is of greater significance to urban residence in China. Actually, the measure to apply computer aided design software into residential design can effectively avoid an inconformity of design intent with actual using condition, and a negative impact on users due to bad architectural physics environment of buildings, etc. The paper largely adopts a design method of analyzing architectural physics environment of residential public space. By analyzing and evaluating various physics environments, a suitability assessment is obtained for residential public space, thereby guiding the space design.

Environmental Assessment: Proposed Automotive/Arts and Crafts Skills Center, Hill Air Force Base, Utah

DTIC Science & Technology

2010-10-14

Water regarding potential sources of t practices to ensure drinking water source protection. u ity design and operating standards would be based...center would not be constructed, and adequate facilities would not be provided. The existing facility would operate as it currently exists...would be properly handled during the construction process. Operational activities would generate the same types of waste as the existing facility

Topics for Educational Policymakers.

ERIC Educational Resources Information Center

Texas Association of School Boards, Austin.

The primary responsibility of school board members has always been the development of the policies that govern the school district. If these policies are to properly address the actual needs of the school district they must be based on an accurate and comprehensive knowledge of the issue confronting the district. This handbook is designed first to…

Sustaining Higher Education Reforms: Knowledge and Policy Implications Learned from Thailand

ERIC Educational Resources Information Center

Phusavat, Kongkiti; Ketsarapong, Suphattra; Ooi, Keng-Boon; Shyu, Stacy H.P.

2012-01-01

Purpose: The paper aims to share experiences in Thailand's higher educational reforms in which academic excellence cannot be sustained without proper financial and fiscal consideration. The overall goal is to disclose the experiences and future issues facing public universities. Design/methodology/approach: The paper is based on actual involvement…

Dynamic Vision for Control

DTIC Science & Technology

2009-02-05

the best of our knowledge, the first approach to design a proper filter (observer) in the infinite - dimensional space of shapes (closed Jordan...curves). This is based on endowing the space with a Riemaimian (Sobolev) metric , then shooting geodesies from the current best estimate of the state...handing nuisance transformations and endowing the models with a

Assessing Collaboration Networks in Educational Research: A Co-Authorship-Based Social Network Analysis Approach

ERIC Educational Resources Information Center

Munoz, David Andres; Queupil, Juan Pablo; Fraser, Pablo

2016-01-01

Purpose: The purpose of this paper is to analyze collaboration networks and their patterns among higher education institutions (HEIs) in Chile and the Latin American region. This will provide evidence to educational managements in order to properly allocate their efforts to improve collaboration. Design/methodology/approach: This quantitative…

COMPUTER TECHNIQUES FOR WEEKLY MULTIPLE-CHOICE TESTING.

ERIC Educational Resources Information Center

BROYLES, DAVID

TO ENCOURAGE POLITICAL SCIENCE STUDENTS TO READ PROPERLY AND CONTINUOUSLY, THE AUTHOR GIVES FREQUENT SHORT QUIZZES BASED ON THE ASSIGNED READINGS. FOR EASE IN ADMINISTRATION AND SCORING, HE USES MARK-SENSE CARDS, ON WHICH THE STUDENT MARKS DESIGNATED AREAS TO INDICATE HIS NUMBER AND HIS CHOICE OF ANSWERS. TO EMPHASIZE THE VALUE OF CONTINUED HIGH…

Multimedia Presentations in Educational Measurement and Statistics: Design Considerations and Instructional Approaches

ERIC Educational Resources Information Center

Sklar, Jeffrey C.; Zwick, Rebecca

2009-01-01

Proper interpretation of standardized test scores is a crucial skill for K-12 teachers and school personnel; however, many do not have sufficient knowledge of measurement concepts to appropriately interpret and communicate test results. In a recent four-year project funded by the National Science Foundation, three web-based instructional…

The Development of an Expert System for the Creative Design of Mechanisms

DTIC Science & Technology

1989-06-26

adjacelnt Link-1 Figue 41 B.Semntc newr-bae knowlede representto cee 25 4.3 Planning Control in Mechanism Design In a "plain", rule-based expert system...the contracted level, ensures the non-crossing feature. 2. Geometrical: handled at the monochrome level, manages the approximate size of links. 3...Ornamental: handled at the colored level, manages proper orientations between binary links and other miscellaneous appearance of the sketch. Each stage

78 FR 52929 - Scientific Information Request on Imaging Tests for the Diagnosis and Staging of Pancreatic...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-27

... improve the quality of this review. AHRQ is conducting this comparative effectiveness review pursuant to..., study period, design, methodology, indication and diagnosis, proper use instructions, inclusion and... including a study number, the study period, design, methodology, indication and diagnosis, proper use...

Recommendations for research design of telehealth studies.

PubMed

Chumbler, Neale R; Kobb, Rita; Brennan, David M; Rabinowitz, Terry

2008-11-01

Properly designed randomized controlled trials (RCTs) are the gold standard to use when examining the effectiveness of telehealth interventions on clinical outcomes. Some published telehealth studies have employed well-designed RCTs. However, such methods are not always feasible and practical in particular settings. This white paper addresses not only the need for properly designed RCTs, but also offers alternative research designs, such as quasi-experimental designs, and statistical techniques that can be employed to rigorously assess the effectiveness of telehealth studies. This paper further offers design and measurement recommendations aimed at and relevant to administrative decision-makers, policymakers, and practicing clinicians.

Development of Integrated Modular Avionics Application Based on Simulink and XtratuM

NASA Astrophysics Data System (ADS)

Fons-Albert, Borja; Usach-Molina, Hector; Vila-Carbo, Joan; Crespo-Lorente, Alfons

2013-08-01

This paper presents an integral approach for designing avionics applications that meets the requirements for software development and execution of this application domain. Software design follows the Model-Based design process and is performed in Simulink. This approach allows easy and quick testbench development and helps satisfying DO-178B requirements through the use of proper tools. The software execution platform is based on XtratuM, a minimal bare-metal hypervisor designed in our research group. XtratuM provides support for IMA-SP (Integrated Modular Avionics for Space) architectures. This approach allows the code generation of a Simulink model to be executed on top of Lithos as XtratuM partition. Lithos is a ARINC-653 compliant RTOS for XtratuM. The paper concentrates in how to smoothly port Simulink designs to XtratuM solving problems like application partitioning, automatic code generation, real-time tasking, interfacing, and others. This process is illustrated with an autopilot design test using a flight simulator.

Design of CMOS imaging system based on FPGA

NASA Astrophysics Data System (ADS)

Hu, Bo; Chen, Xiaolai

2017-10-01

In order to meet the needs of engineering applications for high dynamic range CMOS camera under the rolling shutter mode, a complete imaging system is designed based on the CMOS imaging sensor NSC1105. The paper decides CMOS+ADC+FPGA+Camera Link as processing architecture and introduces the design and implementation of the hardware system. As for camera software system, which consists of CMOS timing drive module, image acquisition module and transmission control module, the paper designs in Verilog language and drives it to work properly based on Xilinx FPGA. The ISE 14.6 emulator ISim is used in the simulation of signals. The imaging experimental results show that the system exhibits a 1280*1024 pixel resolution, has a frame frequency of 25 fps and a dynamic range more than 120dB. The imaging quality of the system satisfies the requirement of the index.

Design technique for all-dielectric non-polarizing beam splitter plate

NASA Astrophysics Data System (ADS)

Rizea, A.

2012-03-01

There are many situations when, for the proper working, an opto-electronic device requiring optical components does not change the polarization state of light after a reflection, splitting or filtering. In this paper, a design for a non-polarizing beam splitter plate is proposed. Based on certain optical properties of homogeneous dielectric materials we will establish a reliable thin film package formula, excellent for the start of optimization to obtain a 20-nm bandwidth non-polarizing beam splitter.

Challenges Surrounding the Injection and Arrival of Targets at LIFE Fusion Chamber Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miles, R; Spaeth, M; Manes, K

2010-12-01

IFE target designers must consider several engineering requirements in addition to the physics requirements for successful target implosion. These considerations include low target cost, high manufacturing throughput, the ability of the target to survive the injection into the fusion chamber and arrive in a condition and physical position consistent with proper laser-target interaction and ease of post-implosion debris removal. This article briefly describes these considerations for the Laser Inertial Fusion-based Energy (LIFE) targets currently being designed.

Technological Literacy: The Proper Focus to Educate All Students

ERIC Educational Resources Information Center

Loveland, Thomas; Love, Tyler

2017-01-01

As technology and engineering (T&E) education seeks to survive a shortage of teachers and funding, among other factors, it must proceed with caution. The field should remain true to its hands-on, design-based roots but must also provide rigorous instruction that applies STEM skills and situates it as a valuable stakeholder among the core…

Learning Opportunities in a Department-Wide Crisis Simulation: Bridging the International/National Divide

ERIC Educational Resources Information Center

Zaino, Jeanne S.; Mulligan, Tricia

2009-01-01

When designed and executed properly, role-playing simulations go a long way to enhance student learning. Typically, however, simulations are divided along subfields. Most exercises, whether based on real or fictitious events, either place students in various roles within a country or have them represent the international interests of one country…

Designing, Assessing, and Demonstrating Sustainable Bioaugmentation for Treatment of DNAPL Sources in Fractured Bedrock

DTIC Science & Technology

2017-03-27

the project, and was based on CB&I’s experience at DoD sites, a literature review, and by discussions with site contractors , regulators, and DoD...to collection in the holding tank ( HT -1) for characterization and proper disposal. The use of GAC and diversion to the holding tank was only employed

A quantitative analysis of statistical power identifies obesity end points for improved in vivo preclinical study design.

PubMed

Selimkhanov, J; Thompson, W C; Guo, J; Hall, K D; Musante, C J

2017-08-01

The design of well-powered in vivo preclinical studies is a key element in building the knowledge of disease physiology for the purpose of identifying and effectively testing potential antiobesity drug targets. However, as a result of the complexity of the obese phenotype, there is limited understanding of the variability within and between study animals of macroscopic end points such as food intake and body composition. This, combined with limitations inherent in the measurement of certain end points, presents challenges to study design that can have significant consequences for an antiobesity program. Here, we analyze a large, longitudinal study of mouse food intake and body composition during diet perturbation to quantify the variability and interaction of the key metabolic end points. To demonstrate how conclusions can change as a function of study size, we show that a simulated preclinical study properly powered for one end point may lead to false conclusions based on secondary end points. We then propose the guidelines for end point selection and study size estimation under different conditions to facilitate proper power calculation for a more successful in vivo study design.

An innovative approach to compensator design

NASA Technical Reports Server (NTRS)

Mitchell, J. R.; Mcdaniel, W. L., Jr.

1973-01-01

The design is considered of a computer-aided-compensator for a control system from a frequency domain point of view. The design technique developed is based on describing the open loop frequency response by n discrete frequency points which result in n functions of the compensator coefficients. Several of these functions are chosen so that the system specifications are properly portrayed; then mathematical programming is used to improve all of these functions which have values below minimum standards. To do this, several definitions in regard to measuring the performance of a system in the frequency domain are given, e.g., relative stability, relative attenuation, proper phasing, etc. Next, theorems which govern the number of compensator coefficients necessary to make improvements in a certain number of functions are proved. After this a mathematical programming tool for aiding in the solution of the problem is developed. This tool is called the constraint improvement algorithm. Then for applying the constraint improvement algorithm generalized, gradients for the constraints are derived. Finally, the necessary theory is incorporated in a Computer program called CIP (compensator Improvement Program). The practical usefulness of CIP is demonstrated by two large system examples.

Technique for controlling spread of limnotic oncomelania

NASA Astrophysics Data System (ADS)

Li, Damei; Wang, Xiangsan; Lai, Yonggen

2003-09-01

Schistosomiasis is a parasitic disease mostly found in areas along the Changjiang River of China. The disease is spread solely through an intermediary named oncomelania, so its spread of schistosomiasis can be controlled by properly designing water intakes which prevent oncomelania from entering farming land or residential areas. This paper reports a successful design process and a new oncomelania-free intake device. The design of the new intake is based on a sound research program in which extensive experimental studies were carried out to gain knowledge of oncomelania eco-hydraulic behavior and detailed flow field information through CFD simulation.

Teaching childbirth with high-fidelity simulation. Is it better observing the scenario during the briefing session?

PubMed

Cuerva, Marcos J; Piñel, Carlos S; Martin, Lourdes; Espinosa, Jose A; Corral, Octavio J; Mendoza, Nicolás

2018-02-12

The design of optimal courses for obstetric undergraduate teaching is a relevant question. This study evaluates two different designs of simulator-based learning activity on childbirth with regard to respect to the patient, obstetric manoeuvres, interpretation of cardiotocography tracings (CTG) and infection prevention. This randomised experimental study which differs in the content of their briefing sessions consisted of two groups of undergraduate students, who performed two simulator-based learning activities on childbirth. The first briefing session included the observations of a properly performed scenario according to Spanish clinical practice guidelines on care in normal childbirth by the teachers whereas the second group did not include the observations of a properly performed scenario, and the students observed it only after the simulation process. The group that observed a properly performed scenario after the simulation obtained worse grades during the simulation, but better grades during the debriefing and evaluation. Simulator use in childbirth may be more fruitful when the medical students observe correct performance at the completion of the scenario compared to that at the start of the scenario. Impact statement What is already known on this subject? There is a scarcity of literature about the design of optimal high-fidelity simulation training in childbirth. It is known that preparing simulator-based learning activities is a complex process. Simulator-based learning includes the following steps: briefing, simulation, debriefing and evaluation. The most important part of high-fidelity simulations is the debriefing. A good briefing and simulation are of high relevance in order to have a fruitful debriefing session. What do the results of this study add? Our study describes a full simulator-based learning activity on childbirth that can be reproduced in similar facilities. The findings of this study add that high-fidelity simulation training in childbirth is favoured by a short briefing session and an abrupt start to the scenario, rather than a long briefing session that includes direct instruction in the scenario. What are the implications of these findings for clinical practice and/or further research? The findings of this study reveal what to include in the briefing of simulator-based learning activities on childbirth. These findings have implications in medical teaching and in medical practice.

Design of low noise imaging system

NASA Astrophysics Data System (ADS)

Hu, Bo; Chen, Xiaolai

2017-10-01

In order to meet the needs of engineering applications for low noise imaging system under the mode of global shutter, a complete imaging system is designed based on the SCMOS (Scientific CMOS) image sensor CIS2521F. The paper introduces hardware circuit and software system design. Based on the analysis of key indexes and technologies about the imaging system, the paper makes chips selection and decides SCMOS + FPGA+ DDRII+ Camera Link as processing architecture. Then it introduces the entire system workflow and power supply and distribution unit design. As for the software system, which consists of the SCMOS control module, image acquisition module, data cache control module and transmission control module, the paper designs in Verilog language and drives it to work properly based on Xilinx FPGA. The imaging experimental results show that the imaging system exhibits a 2560*2160 pixel resolution, has a maximum frame frequency of 50 fps. The imaging quality of the system satisfies the requirement of the index.

Reliability-based design optimization using a generalized subset simulation method and posterior approximation

NASA Astrophysics Data System (ADS)

Ma, Yuan-Zhuo; Li, Hong-Shuang; Yao, Wei-Xing

2018-05-01

The evaluation of the probabilistic constraints in reliability-based design optimization (RBDO) problems has always been significant and challenging work, which strongly affects the performance of RBDO methods. This article deals with RBDO problems using a recently developed generalized subset simulation (GSS) method and a posterior approximation approach. The posterior approximation approach is used to transform all the probabilistic constraints into ordinary constraints as in deterministic optimization. The assessment of multiple failure probabilities required by the posterior approximation approach is achieved by GSS in a single run at all supporting points, which are selected by a proper experimental design scheme combining Sobol' sequences and Bucher's design. Sequentially, the transformed deterministic design optimization problem can be solved by optimization algorithms, for example, the sequential quadratic programming method. Three optimization problems are used to demonstrate the efficiency and accuracy of the proposed method.

Surrogate models for sheet metal stamping problem based on the combination of proper orthogonal decomposition and radial basis function

NASA Astrophysics Data System (ADS)

Dang, Van Tuan; Lafon, Pascal; Labergere, Carl

2017-10-01

In this work, a combination of Proper Orthogonal Decomposition (POD) and Radial Basis Function (RBF) is proposed to build a surrogate model based on the Benchmark Springback 3D bending from the Numisheet2011 congress. The influence of the two design parameters, the geometrical parameter of the die radius and the process parameter of the blank holder force, on the springback of the sheet after a stamping operation is analyzed. The classical Design of Experience (DoE) uses Full Factorial to design the parameter space with sample points as input data for finite element method (FEM) numerical simulation of the sheet metal stamping process. The basic idea is to consider the design parameters as additional dimensions for the solution of the displacement fields. The order of the resultant high-fidelity model is reduced through the use of POD method which performs model space reduction and results in the basis functions of the low order model. Specifically, the snapshot method is used in our work, in which the basis functions is derived from snapshot deviation of the matrix of the final displacements fields of the FEM numerical simulation. The obtained basis functions are then used to determine the POD coefficients and RBF is used for the interpolation of these POD coefficients over the parameter space. Finally, the presented POD-RBF approach which is used for shape optimization can be performed with high accuracy.

Improved optical design of nontracking concentrators

NASA Astrophysics Data System (ADS)

Kwan, B. M.; Bannerot, R. B.

1984-08-01

Optical designs based on a two reflections or less criterion have been developed for one and two-facet trapezoidal concentrators. Collector designs resulting from this criterion have been evaluated with the aid of a ray-trace computer simulation which includes the effects of nonideal reflectors. Results indicate a marked increase in performance, particularly for the one-facet designs, as compared to the collectors previously designed with the one reflection or less criterion. A significant result is that when a proper accounting is made for the actual acceptance angle for the concentrators, the performances of the optimal one and two-facet designs become nearly identical, indicating that the previously held contention that improved performance could be achieved with multifaceted reflectors (geometrically approaching the compound parabolic shape) may be incorrect.

Design considerations and quantitative assessment for the development of percutaneous mitral valve stent.

PubMed

Kumar, Gideon Praveen; Cui, Fangsen; Phang, Hui Qun; Su, Boyang; Leo, Hwa Liang; Hon, Jimmy Kim Fatt

2014-07-01

Percutaneous heart valve replacement is gaining popularity, as more positive reports of satisfactory early clinical experiences are published. However this technique is mostly used for the replacement of pulmonary and aortic valves and less often for the repair and replacement of atrioventricular valves mainly due to their anatomical complexity. While the challenges posed by the complexity of the mitral annulus anatomy cannot be mitigated, it is possible to design mitral stents that could offer good anchorage and support to the valve prosthesis. This paper describes four new Nitinol based mitral valve designs with specific features intended to address migration and paravalvular leaks associated with mitral valve designs. The paper also describes maximum possible crimpability assessment of these mitral stent designs using a crimpability index formulation based on the various stent design parameters. The actual crimpability of the designs was further evaluated using finite element analysis (FEA). Furthermore, fatigue modeling and analysis was also done on these designs. One of the models was then coated with polytetrafluoroethylene (PTFE) with leaflets sutured and put to: (i) leaflet functional tests to check for proper coaptation of the leaflet and regurgitation leakages on a phantom model and (ii) anchorage test where the stented valve was deployed in an explanted pig heart. Simulations results showed that all the stents designs could be crimped to 18F without mechanical failure. Leaflet functional test results showed that the valve leaflets in the fabricated stented valve coapted properly and the regurgitation leakage being within acceptable limits. Deployment of the stented valve in the explanted heart showed that it anchors well in the mitral annulus. Based on these promising results of the one design tested, the other stent models proposed here were also considered to be promising for percutaneous replacement of mitral valves for the treatment of mitral regurgitation, by virtue of their key features as well as effective crimping. These models will be fabricated and put to all the aforementioned tests before being taken for animal trials. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Study/experimental/research design: much more than statistics.

PubMed

Knight, Kenneth L

2010-01-01

The purpose of study, experimental, or research design in scientific manuscripts has changed significantly over the years. It has evolved from an explanation of the design of the experiment (ie, data gathering or acquisition) to an explanation of the statistical analysis. This practice makes "Methods" sections hard to read and understand. To clarify the difference between study design and statistical analysis, to show the advantages of a properly written study design on article comprehension, and to encourage authors to correctly describe study designs. The role of study design is explored from the introduction of the concept by Fisher through modern-day scientists and the AMA Manual of Style. At one time, when experiments were simpler, the study design and statistical design were identical or very similar. With the complex research that is common today, which often includes manipulating variables to create new variables and the multiple (and different) analyses of a single data set, data collection is very different than statistical design. Thus, both a study design and a statistical design are necessary. Scientific manuscripts will be much easier to read and comprehend. A proper experimental design serves as a road map to the study methods, helping readers to understand more clearly how the data were obtained and, therefore, assisting them in properly analyzing the results.

Self-optimizing Pitch Control for Large Scale Wind Turbine Based on ADRC

NASA Astrophysics Data System (ADS)

Xia, Anjun; Hu, Guoqing; Li, Zheng; Huang, Dongxiao; Wang, Fengxiang

2018-01-01

Since wind turbine is a complex nonlinear and strong coupling system, traditional PI control method can hardly achieve good control performance. A self-optimizing pitch control method based on the active-disturbance-rejection control theory is proposed in this paper. A linear model of the wind turbine is derived by linearizing the aerodynamic torque equation and the dynamic response of wind turbine is transformed into a first-order linear system. An expert system is designed to optimize the amplification coefficient according to the pitch rate and the speed deviation. The purpose of the proposed control method is to regulate the amplification coefficient automatically and keep the variations of pitch rate and rotor speed in proper ranges. Simulation results show that the proposed pitch control method has the ability to modify the amplification coefficient effectively, when it is not suitable, and keep the variations of pitch rate and rotor speed in proper ranges

An Instructional Design Using the Virtual Ecological Pond for Science Education in Elementary Schools

ERIC Educational Resources Information Center

Tarng, Wernhuar; Ou, Kuo-Liang; Tsai, Wen-Shin; Lin, Yu-Si; Hsu, Chen-Kai

2010-01-01

Ecological ponds can be a good teaching tool for science teachers, but they must be built and maintained properly to provide students with a safe and suitable learning environment. However, many schools do not have the ability to build and maintain an ecological pond. This study used virtual reality technology to develop a web-based virtual…

GIS based solid waste management information system for Nagpur, India.

PubMed

Vijay, Ritesh; Jain, Preeti; Sharma, N; Bhattacharyya, J K; Vaidya, A N; Sohony, R A

2013-01-01

Solid waste management is one of the major problems of today's world and needs to be addressed by proper utilization of technologies and design of effective, flexible and structured information system. Therefore, the objective of this paper was to design and develop a GIS based solid waste management information system as a decision making and planning tool for regularities and municipal authorities. The system integrates geo-spatial features of the city and database of existing solid waste management. GIS based information system facilitates modules of visualization, query interface, statistical analysis, report generation and database modification. It also provides modules like solid waste estimation, collection, transportation and disposal details. The information system is user-friendly, standalone and platform independent.

Structural Analysis Using Computer Based Methods

NASA Technical Reports Server (NTRS)

Dietz, Matthew R.

2013-01-01

The stiffness of a flex hose that will be used in the umbilical arms of the Space Launch Systems mobile launcher needed to be determined in order to properly qualify ground umbilical plate behavior during vehicle separation post T-0. This data is also necessary to properly size and design the motors used to retract the umbilical arms. Therefore an experiment was created to determine the stiffness of the hose. Before the test apparatus for the experiment could be built, the structure had to be analyzed to ensure it would not fail under given loading conditions. The design model was imported into the analysis software and optimized to decrease runtime while still providing accurate restlts and allow for seamless meshing. Areas exceeding the allowable stresses in the structure were located and modified before submitting the design for fabrication. In addition, a mock up of a deep space habitat and the support frame was designed and needed to be analyzed for structural integrity under different loading conditions. The load cases were provided by the customer and were applied to the structure after optimizing the geometry. Once again, weak points in the structure were located and recommended design changes were made to the customer and the process was repeated until the load conditions were met without exceeding the allowable stresses. After the stresses met the required factors of safety the designs were released for fabrication.

Mason Bee Habitations: Teaching Proper "Making" Skill through Authentic Engineering Design Contests. Resources in Technology and Engineering

ERIC Educational Resources Information Center

Cool, Nate; Strimel, Greg J.; Croly, Michael; Grubbs, Michael E.

2017-01-01

To be technologically and engineering literate, people should be able to "make" or produce quality solutions to engineering design challenges while recognizing and understanding how to avoid hazards in a broad array of situations when properly using tools, machines, and materials (Haynie, 2009; Gunter, 2007; ITEA/ITEEA, 2000/2002/2007).…

Natural gas availability and ambient air quality in the Baton Rouge/New Orleans industrial complex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fieler, E.R.; Harrison, D.P.

1978-02-26

Three scenarios were modeled for the Baton Rouge/New Orleans area for 1985: one assumes the substitution of residual oil (0.7% sulfur) for gas to decrease gas-burning stationary sources from 80 to 8% and the use of properly designed stacks for large emitters; the second makes identical gas supply assumptions but adds proper stack dispersion for medium as well as large emitters; and the third is based on 16% gas-burning stationary sources. The Climatological Dispersion Model was used to translate (1974) emission rates into ambient air concentrations. Growth rates for residential, commercial, and transportation sources, but not industry, were considered. Themore » results show that proper policies, which would require not only tall stacks for large oil burning units (and for intermediate units also in the areas of high industrial concentration), but also the careful location of new plants would permit continued industrial expansion without severe air pollution problems.« less

Making a Back-Illuminated Imager with Back-Side Contact and Alignment Markers

NASA Technical Reports Server (NTRS)

Pain, Bedabrata

2008-01-01

A design modification and a fabrication process that implements the modification have been conceived to solve two problems encountered in the development of back-illuminated, back-sidethinned complementary metal oxide/ semiconductor (CMOS) image-detector integrated circuits. The two problems are (1) how to form metal electrical-contact pads on the back side that are electrically connected through the thickness in proper alignment with electrical contact points on the front side and (2) how to provide alignment keys on the back side to ensure proper registration of backside optical components (e.g., microlenses and/or color filters) with the front-side pixel pattern. The essence of the design modification is to add metal plugs that extend from the desired front-side locations through the thickness and protrude from the back side of the substrate. The plugs afford the required front-to-back electrical conduction, and the protrusions of the plugs serve as both the alignment keys and the bases upon which the back-side electrical-contact pads can be formed.

Shredded Waste Downdraft Gasifier for Overseas Contingency Operations Waste-to-Energy Conversion

DTIC Science & Technology

2015-06-01

results of the proposed experimental test plan and the design of a shredded waste WEC system in Task 5. A. Generators (Left) and Shredded...Shredded Waste 4 8.5 – 27.1 5.1.1.4 Wall Friction Tests In addition to a properly sized outlet, the design of a mass flow vessel must consider...consolidating pressures. 5.1.2.3 Wall Friction Tests In addition to a properly sized outlet, the design of a mass flow vessel must consider the

Workplace Design

NASA Technical Reports Server (NTRS)

1984-01-01

The Anthropometric Source Book was developed based on Johnson Space Center project of anthropometry, the study of the size, shape and motion characteristics of the human body. Designed primarily for use by NASA, the military services and aerospace contractors, the book was also intended to help non-aerospace engineers, architects, and others engaged in design of clothing, equipment and workplaces. An example of its use by Eastman Kodak Company is the company's application of the data to design efficient, productive and comfortable workplaces for employees in the Rochester, NY processing laboratories. The sourcebook was used to determine such dimensions as leg space, work surface height and thickness, employee reach distances, proper height for computer terminal screen, seat height and knee space.

Structural design/margin assessment

NASA Technical Reports Server (NTRS)

Ryan, R. S.

1993-01-01

Determining structural design inputs and the structural margins following design completion is one of the major activities in space exploration. The end result is a statement of these margins as stability, safety factors on ultimate and yield stresses, fracture limits (fracture control), fatigue lifetime, reuse criteria, operational criteria and procedures, stability factors, deflections, clearance, handling criteria, etc. The process is normally called a load cycle and is time consuming, very complex, and involves much more than structures. The key to successful structural design is the proper implementation of the process. It depends on many factors: leadership and management of the process, adequate analysis and testing tools, data basing, communications, people skills, and training. This process and the various factors involved are discussed.

A Quartz Crystal Microbalance dew point sensor without frequency measurement.

PubMed

Wang, Guohua; Zhang, Weishuo; Wang, Shuo; Sun, Jinglin

2014-11-01

This work deals with the design of a dew point sensor based on Quartz Crystal Microbalance (QCM) without measuring the frequency. This idea is inspired by the fact that the Colpitts oscillation circuit will stop oscillating when the QCM works in the liquid media. The quartz crystal and the electrode are designed through the finite element simulation and the stop oscillating experiment is conducted to verify the sensibility. Moreover, the measurement result is calibrated to approach the true value. At last a series of dew points at the same temperature is measured with the designed sensor. Results show that the designed dew point sensor is able to detect the dew point with the proper accuracy.

Easy method of matching fighter engine to airframe for use in aircraft engine design courses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattingly, J.D.

1989-01-01

The proper match of the engine(s) to the airframe affects both aircraft size and life cycle cost. A fast and straightforward method is developed and used for the matching of fighter engine(s) to airframes during conceptual design. A thrust-lapse equation is developed for the dual-spool, mixed-flow, afterburning turbofan type of engine based on the installation losses of 'Aircraft Engine Design' and the performance predictions of the cycle analysis programs ONX and OFFX. Using system performance requirements, the effects of aircraft thrust-to-weight, wing loading, and engine cycle on takeoff weight are analyzed and example design course results presented. 5 refs.

A quartz crystal microbalance dew point sensor without frequency measurement

NASA Astrophysics Data System (ADS)

Wang, Guohua; Zhang, Weishuo; Wang, Shuo; Sun, Jinglin

2014-11-01

This work deals with the design of a dew point sensor based on Quartz Crystal Microbalance (QCM) without measuring the frequency. This idea is inspired by the fact that the Colpitts oscillation circuit will stop oscillating when the QCM works in the liquid media. The quartz crystal and the electrode are designed through the finite element simulation and the stop oscillating experiment is conducted to verify the sensibility. Moreover, the measurement result is calibrated to approach the true value. At last a series of dew points at the same temperature is measured with the designed sensor. Results show that the designed dew point sensor is able to detect the dew point with the proper accuracy.

Statistical Analyses of Femur Parameters for Designing Anatomical Plates.

PubMed

Wang, Lin; He, Kunjin; Chen, Zhengming

2016-01-01

Femur parameters are key prerequisites for scientifically designing anatomical plates. Meanwhile, individual differences in femurs present a challenge to design well-fitting anatomical plates. Therefore, to design anatomical plates more scientifically, analyses of femur parameters with statistical methods were performed in this study. The specific steps were as follows. First, taking eight anatomical femur parameters as variables, 100 femur samples were classified into three classes with factor analysis and Q-type cluster analysis. Second, based on the mean parameter values of the three classes of femurs, three sizes of average anatomical plates corresponding to the three classes of femurs were designed. Finally, based on Bayes discriminant analysis, a new femur could be assigned to the proper class. Thereafter, the average anatomical plate suitable for that new femur was selected from the three available sizes of plates. Experimental results showed that the classification of femurs was quite reasonable based on the anatomical aspects of the femurs. For instance, three sizes of condylar buttress plates were designed. Meanwhile, 20 new femurs are judged to which classes the femurs belong. Thereafter, suitable condylar buttress plates were determined and selected.

Modelling operations and security of cloud systems using Z-notation and Chinese Wall security policy

NASA Astrophysics Data System (ADS)

Basu, Srijita; Sengupta, Anirban; Mazumdar, Chandan

2016-11-01

Enterprises are increasingly using cloud computing for hosting their applications. Availability of fast Internet and cheap bandwidth are causing greater number of people to use cloud-based services. This has the advantage of lower cost and minimum maintenance. However, ensuring security of user data and proper management of cloud infrastructure remain major areas of concern. Existing techniques are either too complex, or fail to properly represent the actual cloud scenario. This article presents a formal cloud model using the constructs of Z-notation. Principles of the Chinese Wall security policy have been applied to design secure cloud-specific operations. The proposed methodology will enable users to safely host their services, as well as process sensitive data, on cloud.

Heart Rate Monitor for Portable MP3 Player.

PubMed

Kim, Jaywoo; Lee, Mi-Hee; Lee, Hyoung-Ki; Choi, Kiwan; Bang, Seokwon; Kim, Sangryong

2005-01-01

This paper presents a photoplethysmography sensor based on a heart rate monitor for a portable MP3 player. Two major design issues are addressed: one is to acquire the sensor signal with a proper amplitude despite a wide range of variation and the other is to handle the noise contaminated signal which is caused by a motion artifact. A benchmarking test with a professional medical photoplethysmography sensor shows that our device performs very well in calculating heart rate even though our photoplethysmography sensor module was designed to be cost effective.

Low Noise Amplifiers Based on Lattice Engineered Substrates

DTIC Science & Technology

2004-11-01

the base contacts. To overcome this deficiency, a current aperture must be adopted in the emitter to properly channel the carriers. Appendix V is a...Appendix V "Design and Fabrication of Collector-up Heterojunction BipolarTransistors with Oxide Confined Current Apertures," James G. Champlain and Umesh K...a consequence of the [110] elimination of steps which were produced during plastic re- o, .A,,A A A A’YAL , V IA VP ’ \\P4 laxation of the misfit strain

Achieving World Class: An Independent Review of the Design Plans for the Walter Reed National Military Medical Center and the Fort Belvoir Community Hospital

DTIC Science & Technology

2009-05-01

class medical facility. Based on a review of relevant reports and other literature, the HSAS’s collective experience and judgment, and extensive...analyses of the demand for PACU services and of the experience and skills of PACU staff relative to the skills needed to properly care for other...class medical facility. Based on a review of relevant reports and other literature, the Subcommittee’s collective experience and judgment, and

Payload Instrument Design Rules for Safe and Efficient Flight Operations

NASA Astrophysics Data System (ADS)

Montagnon, E.; Ferri, P.

2004-04-01

Payload operations are often being neglected in favour of optimisation of scientific performance of the instrument design. This has major drawbacks in terms of cost, safety, efficiency of operations and finally science return. By taking operational aspects into account in the early phases of the instrument design, with a minimum more cultural than financial or technological additional effort, many problems can be avoided or minimized, with significant benefits to be gained in the mission execution phases. This paper presents possible improvements based on the use of the telemetry and telecommand packet standard, proper sharing of autonomy functions between instrument and platform, and enhanced interface documents.

Study/Experimental/Research Design: Much More Than Statistics

PubMed Central

Knight, Kenneth L.

2010-01-01

Abstract Context: The purpose of study, experimental, or research design in scientific manuscripts has changed significantly over the years. It has evolved from an explanation of the design of the experiment (ie, data gathering or acquisition) to an explanation of the statistical analysis. This practice makes “Methods” sections hard to read and understand. Objective: To clarify the difference between study design and statistical analysis, to show the advantages of a properly written study design on article comprehension, and to encourage authors to correctly describe study designs. Description: The role of study design is explored from the introduction of the concept by Fisher through modern-day scientists and the AMA Manual of Style. At one time, when experiments were simpler, the study design and statistical design were identical or very similar. With the complex research that is common today, which often includes manipulating variables to create new variables and the multiple (and different) analyses of a single data set, data collection is very different than statistical design. Thus, both a study design and a statistical design are necessary. Advantages: Scientific manuscripts will be much easier to read and comprehend. A proper experimental design serves as a road map to the study methods, helping readers to understand more clearly how the data were obtained and, therefore, assisting them in properly analyzing the results. PMID:20064054

Standardization of Course Plan and Design of Objective Structured Field Examination (OSFE) for the Assessment of Pharm.D. Student’s Community Pharmacy Clerkship Skills

PubMed Central

Monajjemzadeh, Farnaz; Shokri, Javad; Mohajel Nayebi, Ali Reza; Nemati, Mahboob; Azarmi, Yadollah; Charkhpour, Mohammad; Najafi, Moslem

2014-01-01

Purpose: This study was aimed to design Objective Structured Field Examination (OSFE) and also standardize the course plan of community pharmacy clerkship at Pharmacy Faculty of Tabriz University of Medical Sciences (Iran). Methods: The study was composed of several stages including; evaluation of the old program, standardization and implementation of the new course plan, design and implementation of OSFE, and finally results evaluation. Results: Lack of a fair final assessment protocol and proper organized educating system in various fields of community pharmacy clerkship skills were assigned as the main weaknesses of the old program. Educational priorities were determined and student’s feedback was assessed to design the new curriculum consisting of sessions to fulfill a 60-hour training course. More than 70% of the students were satisfied and successfulness and efficiency of the new clerkship program was significantly greater than the old program (P<0.05). In addition, they believed that OSFE was a suitable testing method. Conclusion: The defined course plan was successfully improved different skills of the students and OSFE was concluded as a proper performance based assessment method. This is easily adoptable by pharmacy faculties to improve the educational outcomes of the clerkship course. PMID:24511477

The constraints satisfaction problem approach in the design of an architectural functional layout

NASA Astrophysics Data System (ADS)

Zawidzki, Machi; Tateyama, Kazuyoshi; Nishikawa, Ikuko

2011-09-01

A design support system with a new strategy for finding the optimal functional configurations of rooms for architectural layouts is presented. A set of configurations satisfying given constraints is generated and ranked according to multiple objectives. The method can be applied to problems in architectural practice, urban or graphic design-wherever allocation of related geometrical elements of known shape is optimized. Although the methodology is shown using simplified examples-a single story residential building with two apartments each having two rooms-the results resemble realistic functional layouts. One example of a practical size problem of a layout of three apartments with a total of 20 rooms is demonstrated, where the generated solution can be used as a base for a realistic architectural blueprint. The discretization of design space is discussed, followed by application of a backtrack search algorithm used for generating a set of potentially 'good' room configurations. Next the solutions are classified by a machine learning method (FFN) as 'proper' or 'improper' according to the internal communication criteria. Examples of interactive ranking of the 'proper' configurations according to multiple criteria and choosing 'the best' ones are presented. The proposed framework is general and universal-the criteria, parameters and weights can be individually defined by a user and the search algorithm can be adjusted to a specific problem.

Mars Tumbleweed Simulation Using Singular Perturbation Theory

NASA Technical Reports Server (NTRS)

Raiszadeh, Behzad; Calhoun, Phillip

2005-01-01

The Mars Tumbleweed is a new surface rover concept that utilizes Martian winds as the primary source of mobility. Several designs have been proposed for the Mars Tumbleweed, all using aerodynamic drag to generate force for traveling about the surface. The Mars Tumbleweed, in its deployed configuration, must be large and lightweight to provide the ratio of drag force to rolling resistance necessary to initiate motion from the Martian surface. This paper discusses the dynamic simulation details of a candidate Tumbleweed design. The dynamic simulation model must properly evaluate and characterize the motion of the tumbleweed rover to support proper selection of system design parameters. Several factors, such as model flexibility, simulation run times, and model accuracy needed to be considered in modeling assumptions. The simulation was required to address the flexibility of the rover and its interaction with the ground, and properly evaluate its mobility. Proper assumptions needed to be made such that the simulated dynamic motion is accurate and realistic while not overly burdened by long simulation run times. This paper also shows results that provided reasonable correlation between the simulation and a drop/roll test of a tumbleweed prototype.

Proposed Models of Appropriate Website and Courseware for E-Learning in Higher Education: Research Based Design Models

ERIC Educational Resources Information Center

Khlaisang, Jintavee

2010-01-01

The purpose of this study was to investigate proper website and courseware for e-learning in higher education. Methods used in this study included the data collection, the analysis surveys, the experts' in-depth interview, and the experts' focus group. Results indicated that there were 16 components for website, as well as 16 components for…

Response surface methodology (RSM) to evaluate moisture effects on corn stover in recovering xylose by DEO hydrolysis

Treesearch

Rita C.L.B. Rodrigues; William R. Kenealy; Diane Dietrich; Thomas W. Jeffries

2012-01-01

Response surface methodology (RSM), based on a 22 full factorial design, evaluated the moisture effects in recovering xylose by diethyloxalate (DEO) hydrolysis. Experiments were carried out in laboratory reactors (10 mL glass ampoules) containing corn stover (0.5 g) properly ground. The ampoules were kept at 160 °C for 90 min. Both DEO...

Advanced Lighting Controls for Reducing Energy Use and Cost in DoD Installations

DTIC Science & Technology

2013-03-01

of advanced lighting control strategies including occupancy sensing, light tuning, daylight harvesting and proper lighting design is an effective way...details of this project and the results obtained. 15. SUBJECT TERMS Integrated lighting controls, occupancy sensing, daylight harvesting , personalized...provide energy savings through occupancy sensing, dimming and daylight harvesting . II. Dynalite is a distributed control-based, wired networked building

Space Environmental Effects (SEE) Testing Capability: NASA/Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

DeWittBurns, H.; Crave, Paul; Finckenor, Miria; Finchum, Charles; Nehls, Mary; Schneider, Todd; Vaughn, Jason

2012-01-01

Understanding the effects of the space environment on materials and systems is fundamental and essential for mission success. If not properly understood and designed for, the space environment can lead to materials degradation, reduction of functional lifetime, and system failure. Ground based testing is critical in predicting performance NASA/MSFC's expertise and capabilities make up the most complete SEE testing capability available.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clausing, R.E.

Equations based on kinetic theory relate the contamination of refractory metals in vacuum to the appropriate variables. Several examples are given for which the allowable system pressures are calculated. The examples illustrate the effect of varying several parameters. The importance of the sticking factor for active gases on hot refractory metals and its effect on the system design are discussed. The data for estimating the sticking factor for O/sub 2/ on Nb are given, along with some estimated values. Experimental data on the composition and rates of outgassing of ultrahigh-vacuum systems and their importance in system design are discussed. Severalmore » methods of reducing contamination rates and the relative ease and effectiveness of these methods are presented. It was concluded that tests of 1000 hr or longer will probably require system pressures of between 10/sup -9/ and 10/sup -6/ torr, the particular pressure depending upon the residual gas composition, test duration, allowable contamination level, and the other variables discussed. Since the most important source of contamination in a properly designed ultrahigh-vacuum system is the outgassing process, bakeable systems should be designed to operate with walls as cool as practical, and to have a minimum of surface area and outgassing materials inside. Considerable added protection may be obtained by incorporating sacrificial getter surfaces in the system, or, alternatively, higher pressures may be tolerated if proper getter design is used. (auth)« less

The stem cell laboratory: design, equipment, and oversight.

PubMed

Wesselschmidt, Robin L; Schwartz, Philip H

2011-01-01

This chapter describes some of the major issues to be considered when setting up a laboratory for the culture of human pluripotent stem cells (hPSCs). The process of establishing a hPSC laboratory can be divided into two equally important parts. One is completely administrative and includes developing protocols, seeking approval, and establishing reporting processes and documentation. The other part of establishing a hPSC laboratory involves the physical plant and includes design, equipment and personnel. Proper planning of laboratory operations and proper design of the physical layout of the stem cell laboratory so that meets the scope of planned operations is a major undertaking, but the time spent upfront will pay long-term returns in operational efficiency and effectiveness. A well-planned, organized, and properly equipped laboratory supports research activities by increasing efficiency and reducing lost time and wasted resources.

Propagation-related AMT design aspects and supporting experiments

NASA Technical Reports Server (NTRS)

Dessouky, Khaled; Estabrook, Polly

1991-01-01

The ACTS Mobile Terminal (AMT) is presently being developed with the goal of significantly extending commercial satellite applications and their user base. A thorough knowledge of the Ka-band channel characteristics is essential to the proper design of a commercially viable system that efficiently utilizes the valuable resources. To date, only limited tests have been performed to characterize the Ka-band channel, and they have focused on the needs of fixed terminals. As part of the value of the AMT as a Ka-band test bed is its function as a vehicle through which tests specifically applicable to the mobile satellite communications can be performed. The exact propagation environment with the proper set of elevation angles, vehicle antenna gains and patterns, roadside shadowing, rain, and Doppler is encountered. The ability to measure all of the above, as well as correlate their effects with observed communication system performance, creates an invaluable opportunity to understand in depth Ka-band's potential in supporting mobile and personal communications. This paper discusses the propagation information required for system design, the setup with ACTS that will enable obtaining this information, and finally the types of experiments to be performed and data to be gathered by the AMT to meet this objective.

Affect-Aware Adaptive Tutoring Based on Human-Automation Etiquette Strategies.

PubMed

Yang, Euijung; Dorneich, Michael C

2018-06-01

We investigated adapting the interaction style of intelligent tutoring system (ITS) feedback based on human-automation etiquette strategies. Most ITSs adapt the content difficulty level, adapt the feedback timing, or provide extra content when they detect cognitive or affective decrements. Our previous work demonstrated that changing the interaction style via different feedback etiquette strategies has differential effects on students' motivation, confidence, satisfaction, and performance. The best etiquette strategy was also determined by user frustration. Based on these findings, a rule set was developed that systemically selected the proper etiquette strategy to address one of four learning factors (motivation, confidence, satisfaction, and performance) under two different levels of user frustration. We explored whether etiquette strategy selection based on this rule set (systematic) or random changes in etiquette strategy for a given level of frustration affected the four learning factors. Participants solved mathematics problems under different frustration conditions with feedback that adapted dynamic changes in etiquette strategies either systematically or randomly. The results demonstrated that feedback with etiquette strategies chosen systematically via the rule set could selectively target and improve motivation, confidence, satisfaction, and performance more than changing etiquette strategies randomly. The systematic adaptation was effective no matter the level of frustration for the participant. If computer tutors can vary the interaction style to effectively mitigate negative emotions, then ITS designers would have one more mechanism in which to design affect-aware adaptations that provide the proper responses in situations where human emotions affect the ability to learn.

Applying causal mediation analysis to personality disorder research.

PubMed

Walters, Glenn D

2018-01-01

This article is designed to address fundamental issues in the application of causal mediation analysis to research on personality disorders. Causal mediation analysis is used to identify mechanisms of effect by testing variables as putative links between the independent and dependent variables. As such, it would appear to have relevance to personality disorder research. It is argued that proper implementation of causal mediation analysis requires that investigators take several factors into account. These factors are discussed under 5 headings: variable selection, model specification, significance evaluation, effect size estimation, and sensitivity testing. First, care must be taken when selecting the independent, dependent, mediator, and control variables for a mediation analysis. Some variables make better mediators than others and all variables should be based on reasonably reliable indicators. Second, the mediation model needs to be properly specified. This requires that the data for the analysis be prospectively or historically ordered and possess proper causal direction. Third, it is imperative that the significance of the identified pathways be established, preferably with a nonparametric bootstrap resampling approach. Fourth, effect size estimates should be computed or competing pathways compared. Finally, investigators employing the mediation method are advised to perform a sensitivity analysis. Additional topics covered in this article include parallel and serial multiple mediation designs, moderation, and the relationship between mediation and moderation. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

An Attempt at Quantifying Factors that Affect Efficiency in the Management of Solid Waste Produced by Commercial Businesses in the City of Tshwane, South Africa

PubMed Central

Worku, Yohannes; Muchie, Mammo

2012-01-01

Objective. The objective was to investigate factors that affect the efficient management of solid waste produced by commercial businesses operating in the city of Pretoria, South Africa. Methods. Data was gathered from 1,034 businesses. Efficiency in solid waste management was assessed by using a structural time-based model designed for evaluating efficiency as a function of the length of time required to manage waste. Data analysis was performed using statistical procedures such as frequency tables, Pearson's chi-square tests of association, and binary logistic regression analysis. Odds ratios estimated from logistic regression analysis were used for identifying key factors that affect efficiency in the proper disposal of waste. Results. The study showed that 857 of the 1,034 businesses selected for the study (83%) were found to be efficient enough with regards to the proper collection and disposal of solid waste. Based on odds ratios estimated from binary logistic regression analysis, efficiency in the proper management of solid waste was significantly influenced by 4 predictor variables. These 4 influential predictor variables are lack of adherence to waste management regulations, wrong perception, failure to provide customers with enough trash cans, and operation of businesses by employed managers, in a decreasing order of importance. PMID:23209483

Explicit parametric solutions of lattice structures with proper generalized decomposition (PGD) - Applications to the design of 3D-printed architectured materials

NASA Astrophysics Data System (ADS)

Sibileau, Alberto; Auricchio, Ferdinando; Morganti, Simone; Díez, Pedro

2018-01-01

Architectured materials (or metamaterials) are constituted by a unit-cell with a complex structural design repeated periodically forming a bulk material with emergent mechanical properties. One may obtain specific macro-scale (or bulk) properties in the resulting architectured material by properly designing the unit-cell. Typically, this is stated as an optimal design problem in which the parameters describing the shape and mechanical properties of the unit-cell are selected in order to produce the desired bulk characteristics. This is especially pertinent due to the ease manufacturing of these complex structures with 3D printers. The proper generalized decomposition provides explicit parametic solutions of parametric PDEs. Here, the same ideas are used to obtain parametric solutions of the algebraic equations arising from lattice structural models. Once the explicit parametric solution is available, the optimal design problem is a simple post-process. The same strategy is applied in the numerical illustrations, first to a unit-cell (and then homogenized with periodicity conditions), and in a second phase to the complete structure of a lattice material specimen.

Toward a view-oriented approach for aligning RDF-based biomedical repositories.

PubMed

Anguita, A; García-Remesal, M; de la Iglesia, D; Graf, N; Maojo, V

2015-01-01

This article is part of the Focus Theme of METHODS of Information in Medicine on "Managing Interoperability and Complexity in Health Systems". The need for complementary access to multiple RDF databases has fostered new lines of research, but also entailed new challenges due to data representation disparities. While several approaches for RDF-based database integration have been proposed, those focused on schema alignment have become the most widely adopted. All state-of-the-art solutions for aligning RDF-based sources resort to a simple technique inherited from legacy relational database integration methods. This technique - known as element-to-element (e2e) mappings - is based on establishing 1:1 mappings between single primitive elements - e.g. concepts, attributes, relationships, etc. - belonging to the source and target schemas. However, due to the intrinsic nature of RDF - a representation language based on defining tuples < subject, predicate, object > -, one may find RDF elements whose semantics vary dramatically when combined into a view involving other RDF elements - i.e. they depend on their context. The latter cannot be adequately represented in the target schema by resorting to the traditional e2e approach. These approaches fail to properly address this issue without explicitly modifying the target ontology, thus lacking the required expressiveness for properly reflecting the intended semantics in the alignment information. To enhance existing RDF schema alignment techniques by providing a mechanism to properly represent elements with context-dependent semantics, thus enabling users to perform more expressive alignments, including scenarios that cannot be adequately addressed by the existing approaches. Instead of establishing 1:1 correspondences between single primitive elements of the schemas, we propose adopting a view-based approach. The latter is targeted at establishing mapping relationships between RDF subgraphs - that can be regarded as the equivalent of views in traditional databases -, rather than between single schema elements. This approach enables users to represent scenarios defined by context-dependent RDF elements that cannot be properly represented when adopting the currently existing approaches. We developed a software tool implementing our view-based strategy. Our tool is currently being used in the context of the European Commission funded p-medicine project, targeted at creating a technological framework to integrate clinical and genomic data to facilitate the development of personalized drugs and therapies for cancer, based on the genetic profile of the patient. We used our tool to integrate different RDF-based databases - including different repositories of clinical trials and DICOM images - using the Health Data Ontology Trunk (HDOT) ontology as the target schema. The importance of database integration methods and tools in the context of biomedical research has been widely recognized. Modern research in this area - e.g. identification of disease biomarkers, or design of personalized therapies - heavily relies on the availability of a technical framework to enable researchers to uniformly access disparate repositories. We present a method and a tool that implement a novel alignment method specifically designed to support and enhance the integration of RDF-based data sources at schema (metadata) level. This approach provides an increased level of expressiveness compared to other existing solutions, and allows solving heterogeneity scenarios that cannot be properly represented using other state-of-the-art techniques.

A microcontroller-based lock-in amplifier for sub-milliohm resistance measurements.

PubMed

Bengtsson, Lars E

2012-07-01

This paper presents a novel approach to the design of a digital ohmmeter with a resolution of <60 μΩ based on a general-purpose microcontroller and a high-impedance instrumentation amplifier only. The design uses two digital I/O-pins to alternate the current through the sample resistor and combined with a proper firmware routine, the design is a lock-in detector that discriminates any signal that is out of phase/frequency with the reference signal. This makes it possible to selectively detect the μV drop across sample resistors down to 55.6 μΩ using only the current that can be supplied by the digital output pins of a microcontroller. This is achieved without the need for an external reference signal generator and does not rely on the computing processing power of a digital signal processor.

Dynamic Compression of the Signal in a Charge Sensitive Amplifier: From Concept to Design

NASA Astrophysics Data System (ADS)

Manghisoni, Massimo; Comotti, Daniele; Gaioni, Luigi; Ratti, Lodovico; Re, Valerio

2015-10-01

This work is concerned with the design of a low-noise Charge Sensitive Amplifier featuring a dynamic signal compression based on the non-linear features of an inversion-mode MOS capacitor. These features make the device suitable for applications where a non-linear characteristic of the front-end is required, such as in imaging instrumentation for free electron laser experiments. The aim of the paper is to discuss a methodology for the proper design of the feedback network enabling the dynamic signal compression. Starting from this compression solution, the design of a low-noise Charge Sensitive Amplifier is also discussed. The study has been carried out by referring to a 65 nm CMOS technology.

Optical design of laser zoom projective lens with variable total track

NASA Astrophysics Data System (ADS)

He, Yulan; Xiao, Xiangguo; Lu, Feng; Li, Yuan; Han, Kunye; Wang, Nanxi; Qiang, Hua

2017-02-01

In order to project the laser command information to the proper distance , so a laser zoom projective lens with variable total track optical system is designed in the carrier-based aircraft landing system. By choosing the zoom structure, designing of initial structure with PW solution, correcting and balancing the aberration, a large variable total track with 35 × zoom is carried out. The size of image is invariable that is φ25m, the distance of projective image is variable from 100m to 3500m. Optical reverse design, the spot is less than 8μm, the MTF is near the diffraction limitation, the value of MTF is bigger than 0.4 at 50lp/mm.

Aerodynamic design of gas and aerosol samplers for aircraft

NASA Technical Reports Server (NTRS)

Soderman, Paul T.; Hazen, Nathan L.; Brune, William H.

1991-01-01

The aerodynamic design of airborne probes for the capture of air and aerosols is discussed. Emphasis is placed on the key parameters that affect proper sampling, such as inlet-lip design, internal duct components for low pressure drop, and exhaust geometry. Inlet designs that avoid sonic flow conditions on the lip and flow separation in the duct are shown. Cross-stream velocities of aerosols are expressed in terms of droplet density and diameter. Flow curvature, which can cause aerosols to cross streamlines and impact on probe walls, can be minimized by means of a proper inlet shape and proper probe orientation, and by avoiding bends upstream of the test section. A NASA panel code called PMARC was used successfully to compute streamlines around aircraft and probes, as well as to compute to local velocity and pressure distributions in inlets. A NACA 1-series inlet with modified lip radius was used for the airborne capture of stratospheric chlorine monoxide at high altitude and high flight speed. The device has a two-stage inlet that decelerates the inflow with little disturbance to the flow through the test section. Diffuser design, exhaust hood design, valve loss, and corner vane geometry are discussed.

Wing design for a civil tiltrotor transport aircraft

NASA Technical Reports Server (NTRS)

Rais-Rohani, Masoud

1994-01-01

The goal of this research is the proper tailoring of the civil tiltrotor's composite wing-box structure leading to a minimum-weight wing design. With focus on the structural design, the wing's aerodynamic shape and the rotor-pylon system are held fixed. The initial design requirement on drag reduction set the airfoil maximum thickness-to-chord ratio to 18 percent. The airfoil section is the scaled down version of the 23 percent-thick airfoil used in V-22's wing. With the project goal in mind, the research activities began with an investigation of the structural dynamic and aeroelastic characteristics of the tiltrotor configuration, and the identification of proper procedures to analyze and account for these characteristics in the wing design. This investigation led to a collection of more than thirty technical papers on the subject, some of which have been referenced here. The review of literature on the tiltrotor revealed the complexity of the system in terms of wing-rotor-pylon interactions. The aeroelastic instability or whirl flutter stemming from wing-rotor-pylon interactions is found to be the most critical mode of instability demanding careful consideration in the preliminary wing design. The placement of wing fundamental natural frequencies in bending and torsion relative to each other and relative to the rotor 1/rev frequencies is found to have a strong influence on the whirl flutter. The frequency placement guide based on a Bell Helicopter Textron study is used in the formulation of frequency constraints. The analysis and design studies are based on two different finite-element computer codes: (1) MSC/NASATRAN and (2) WIDOWAC. These programs are used in parallel with the motivation to eventually, upon necessary modifications and validation, use the simpler WIDOWAC code in the structural tailoring of the tiltrotor wing. Several test cases were studied for the preliminary comparison of the two codes. The results obtained so far indicate a good overall agreement between the two codes.

Design of a Hypermedia-Based Educating System for the Construction of Knowledge

DTIC Science & Technology

1989-09-01

the variety they confront, promote short-term learning . This thesis provides the required background for developing an educating system which promotes...an effective educating system stems frm ever-increasing requirements for learning . Ine Total Quality Management (TQM) program, a Department of Defense...Japan has realized that best efforts ’nly pay off when the workforce is properly educated . Learning has become a pivotal element in the Japanese

The Stem Cell Laboratory: Design, Equipment, and Oversight

PubMed Central

Wesselschmidt, Robin L.; Schwartz, Philip H.

2013-01-01

This chapter describes some of the major issues to be considered when setting up a laboratory for the culture of human pluripotent stem cells (hPSCs). The process of establishing a hPSC laboratory can be divided into two equally important parts. One is completely administrative and includes developing protocols, seeking approval, and establishing reporting processes and documentation. The other part of establishing a hPSC laboratory involves the physical plant and includes design, equipment and personnel. Proper planning of laboratory operations and proper design of the physical layout of the stem cell laboratory so that meets the scope of planned operations is a major undertaking, but the time spent upfront will pay long-term returns in operational efficiency and effectiveness. A well-planned, organized, and properly equipped laboratory supports research activities by increasing efficiency and reducing lost time and wasted resources. PMID:21822863

A polynomial-chaos-expansion-based building block approach for stochastic analysis of photonic circuits

NASA Astrophysics Data System (ADS)

Waqas, Abi; Melati, Daniele; Manfredi, Paolo; Grassi, Flavia; Melloni, Andrea

2018-02-01

The Building Block (BB) approach has recently emerged in photonic as a suitable strategy for the analysis and design of complex circuits. Each BB can be foundry related and contains a mathematical macro-model of its functionality. As well known, statistical variations in fabrication processes can have a strong effect on their functionality and ultimately affect the yield. In order to predict the statistical behavior of the circuit, proper analysis of the uncertainties effects is crucial. This paper presents a method to build a novel class of Stochastic Process Design Kits for the analysis of photonic circuits. The proposed design kits directly store the information on the stochastic behavior of each building block in the form of a generalized-polynomial-chaos-based augmented macro-model obtained by properly exploiting stochastic collocation and Galerkin methods. Using this approach, we demonstrate that the augmented macro-models of the BBs can be calculated once and stored in a BB (foundry dependent) library and then used for the analysis of any desired circuit. The main advantage of this approach, shown here for the first time in photonics, is that the stochastic moments of an arbitrary photonic circuit can be evaluated by a single simulation only, without the need for repeated simulations. The accuracy and the significant speed-up with respect to the classical Monte Carlo analysis are verified by means of classical photonic circuit example with multiple uncertain variables.

Quality Improvement of Ground Works Process with the Use of Chosen Lean Management Tools - Case Study

NASA Astrophysics Data System (ADS)

Nowotarski, Piotr; Paslawski, Jerzy; Wysocki, Bartosz

2017-12-01

Ground works are one of the first processes connected with erecting structures. Based on ground conditions like the type of soil or level of underground water different types and solutions for foundations are designed. Foundations are the base for the buildings, and their proper design and execution is the key for the long and faultless use of the whole construction and might influence on the future costs of the eventual repairs (especially when ground water level is high, and there is no proper water insulation made). Article presents the introduction of chosen Lean Management tools for quality improvement of the process of ground works based on the analysis made on the construction site of vehicle control station located in Poznan, Poland. Processes assessment is made from different perspectives taking into account that 3 main groups of workers were directly involved in the process: blue collar-workers, site manager and site engineers. What is more comparison is made on the 3 points of view to the problems that might occur during this type of works, with details analysis on the causes of such situation? Authors presents also the change of approach of workers directly involved in the mentioned processes regarding introduction of Lean Management methodology, which illustrates the problem of scepticism for new ideas of the people used to perform works and actions in traditional way. Using Lean Management philosophy in construction is a good idea to streamline processes in company, get rid of constantly recurring problems, and in this way improve the productivity and quality of executed activities. Performed analysis showed that different groups of people have very different idea and opinion on the problems connected with executing the same process - ground works and only having full picture of the situation (especially in construction processes) management can take proper problems-preventing actions that consequently can influence on the amount of waste generated on the construction cite which positively influence on the external environment.

Infrared fiber-optic fire sensors - Concepts and designs for Space Station applications

NASA Technical Reports Server (NTRS)

Tapphorn, Ralph M.; Porter, Alan R.

1990-01-01

Various design configurations used for testing IR fiber-optic (IFO) fire-sensor concepts are presented. Responsibility measurements conducted to select the best concept are reviewed. The results indicate that IFO fire-sensor systems based on distributed fiber sensors are feasible for future aerospace applications. For Space Station Freedom, these systems offer alternative fire detectors for monitoring areas within equipment or stage compartments where the ventilation may be inadequate for proper operation of smoke detectors. They also allow a large number of areas to be monitored by a single central detector unit, which reduces the associated cost and weight.

Engineers in the mist: The solar in the jungle project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thornton, J.P.; Thornton, S.

This article describes the design and installation of a photovoltaic power supply for a remote orangutan research station in the rain forest in Borneo. The unique needs of the station, including the problems created by noisy equipment and the transport of fuel offering potential for severe damage, are discussed, along with the design of the system, a community based system for the camp that would not only compensate for shadowing loss due to a chain link cage and meet the daily load, but would provide up to 20 days of energy if loads were managed properly.

A low-cost colorimeter.

PubMed

Jones, N B; Riley, C; Sheya, M S; Hosseinmardi, M M

1984-01-01

A need for a colorimeter with low capital and maintenance costs has been suggested for countries with foreign exchange problems and no local medical instrumentation industry. This paper puts forward a design for such a device based on a domestic light-bulb, photographic filters and photovoltaic cells. The principle of the design is the use of a balancing technique involving twin light paths for test solution and reference solution and an electronic bridge circuit. It is shown that proper selection of the components will allow the cost objectives to be met and also provide acceptable linearity, precision, accuracy and repeatability.

Estimation and control of droplet size and frequency in projected spray mode of a gas metal arc welding (GMAW) process.

PubMed

Anzehaee, Mohammad Mousavi; Haeri, Mohammad

2011-07-01

New estimators are designed based on the modified force balance model to estimate the detaching droplet size, detached droplet size, and mean value of droplet detachment frequency in a gas metal arc welding process. The proper droplet size for the process to be in the projected spray transfer mode is determined based on the modified force balance model and the designed estimators. Finally, the droplet size and the melting rate are controlled using two proportional-integral (PI) controllers to achieve high weld quality by retaining the transfer mode and generating appropriate signals as inputs of the weld geometry control loop. Copyright © 2011 ISA. Published by Elsevier Ltd. All rights reserved.

Lumley's PODT definition of large eddies and a trio of numerical procedures. [Proper Orthogonal Decomposition Theorem

NASA Technical Reports Server (NTRS)

Payne, Fred R.

1992-01-01

Lumley's 1967 Moscow paper provided, for the first time, a completely rational definition of the physically-useful term 'large eddy', popular for a half-century. The numerical procedures based upon his results are: (1) PODT (Proper Orthogonal Decomposition Theorem), which extracts the Large Eddy structure of stochastic processes from physical or computer simulation two-point covariances, and 2) LEIM (Large-Eddy Interaction Model), a predictive scheme for the dynamical large eddies based upon higher order turbulence modeling. Earlier Lumley's work (1964) forms the basis for the final member of the triad of numerical procedures: this predicts the global neutral modes of turbulence which have surprising agreement with both structural eigenmodes and those obtained from the dynamical equations. The ultimate goal of improved engineering design tools for turbulence may be near at hand, partly due to the power and storage of 'supermicrocomputer' workstations finally becoming adequate for the demanding numerics of these procedures.

Economic competitiveness of fuel cell onsite integrated energy systems

NASA Technical Reports Server (NTRS)

Bollenbacher, G.

1983-01-01

The economic competitiveness of fuel cell onsite integrated energy systems (OS/IES) in residential and commercial buildings is examined. The analysis is carried out for three different buildings with each building assumed to be at three geographic locations spanning a range of climatic conditions. Numerous design options and operating strategies are evaluated and two economic criteria are used to measure economic performance. In general the results show that fuel cell OS/IES's are competitive in most regions of the country if the OS/IES is properly designed. The preferred design is grid connected, makes effective use of the fuel cell's thermal output, and has a fuel cell powerplant sized for the building's base electrical load.

Rare-Earth Ions in Niobium-Based Devices as a Quantum Memory: Magneto-Optical Effects on Room Temperature Electrical Transport

DTIC Science & Technology

2016-09-01

rare-earth neodymium by ion implantation in thin films of niobium and niobium-based heterostructure devices. We model the ion implantation process...the films and devices so they can properly designed and optimized for utility as quantum memory. We find that the magnetic field has a strong effect...thin films of niobium. Simulations are made at low 1013 cm-2 and high 1014 cm-2 dose at 60 keV. At high dose, disorder induced is significantly

Distributed software framework and continuous integration in hydroinformatics systems

NASA Astrophysics Data System (ADS)

Zhou, Jianzhong; Zhang, Wei; Xie, Mengfei; Lu, Chengwei; Chen, Xiao

2017-08-01

When encountering multiple and complicated models, multisource structured and unstructured data, complex requirements analysis, the platform design and integration of hydroinformatics systems become a challenge. To properly solve these problems, we describe a distributed software framework and it’s continuous integration process in hydroinformatics systems. This distributed framework mainly consists of server cluster for models, distributed database, GIS (Geographic Information System) servers, master node and clients. Based on it, a GIS - based decision support system for joint regulating of water quantity and water quality of group lakes in Wuhan China is established.

Taking Care of Business.

ERIC Educational Resources Information Center

Stone, William E.

1989-01-01

Properly designed and properly evaluated, entrepreneurial activities can have many kinds of positive financial and non-financial results for an alumni program. A service or product line that alumni can not get from any other source can benefit the budget and both internal and external goodwill. (MSE)

FOOD RISK ANALYSIS

USDA-ARS?s Scientific Manuscript database

Food risk analysis is a holistic approach to food safety because it considers all aspects of the problem. Risk assessment modeling is the foundation of food risk analysis. Proper design and simulation of the risk assessment model is important to properly predict and control risk. Because of knowl...

Guidelines and Suggestions for Balloon Gondola Design

NASA Technical Reports Server (NTRS)

Franco, Hugo

2017-01-01

This paper discusses the current gondola design requirements for the Columbia Scientific Balloon Facility (CSBF). The CSBF is responsible for launching and supporting balloon borne scientific instruments and has some current updated guidelines that will be discussed in this presentation. As the sophistication of Payload systems have increased in size and complexity new guidelines have been implemented in order to make these instruments stay within the acceptable launch risks. Additionally, there is a requirement to submit a proper stress analysis report that states the flight design requirements have been met. Suggestions are discussed in this presentation that establish the proper guidelines to submit these.

Translational Application of Microfluidics and Bioprinting for Stem Cell-Based Cartilage Repair

PubMed Central

Mondadori, Carlotta; Mainardi, Valerio Luca; Talò, Giuseppe; Candrian, Christian; Święszkowski, Wojciech

2018-01-01

Cartilage defects can impair the most elementary daily activities and, if not properly treated, can lead to the complete loss of articular function. The limitations of standard treatments for cartilage repair have triggered the development of stem cell-based therapies. In this scenario, the development of efficient cell differentiation protocols and the design of proper biomaterial-based supports to deliver cells to the injury site need to be addressed through basic and applied research to fully exploit the potential of stem cells. Here, we discuss the use of microfluidics and bioprinting approaches for the translation of stem cell-based therapy for cartilage repair in clinics. In particular, we will focus on the optimization of hydrogel-based materials to mimic the articular cartilage triggered by their use as bioinks in 3D bioprinting applications, on the screening of biochemical and biophysical factors through microfluidic devices to enhance stem cell chondrogenesis, and on the use of microfluidic technology to generate implantable constructs with a complex geometry. Finally, we will describe some new bioprinting applications that pave the way to the clinical use of stem cell-based therapies, such as scaffold-free bioprinting and the development of a 3D handheld device for the in situ repair of cartilage defects. PMID:29535776

An Assessment of Monsoon Triggered Landslides in Western Nepal

NASA Astrophysics Data System (ADS)

Sudan Acharya, Madhu

2010-05-01

Due to heavy monsoon rain, rugged topography and very young mountains, frequent slope failures and soil erosion are very common in Nepal but in most of cases the natural slopes are disturbed by men to construct a road through it and the situation further aggravated by the Monsoon rain. Summer usually tests the disaster response capacity of Nepal, when the monsoons trigger water induced disasters. This year Nepal's Western regions were most severely affected by floods and landslides. Every year, sadly, it is the same story of mostly poor people living in remote villages succumbing to landslides and flooding and those who survive facing hardships brought on by the disaster. The tail end of the monsoon in October has triggered flood and landslides in Nepal which affected a total of 14 districts in the mid and far-west regions, of which Kailali, Bardiya, Banke, Dadeldhura, Accham and Kanchapur district are most affected. The affected areas are geographically scattered and remote, and are therefore difficult to access. In this year (2009), flood and landslides have claimed 62 lives, affecting more than 152,000 individuals from 27,000 families. More than 4,000 families are displaced and are taking shelter in schools, open space and forest areas with no protection from the external elements. In the above context the prevention and mitigation measures for landslides is a great challenge for Nepal. Nepal has been investing its huge amount of resources to stabilize landslides and roadside slope failures, still then it has become unmanageable during Monsoon time. Considering the above facts, an assessment of landslides which were occurred during the Monsoon (July-October 2009), along Khodpe - Jhota - Chainpur road in far western region of Nepal has been carried out based on the field observation of various landslides. The paper presents the causes and mechanisms of failures of different landslides which are mostly triggered by Monsoon rain. It also suggests some low cost mitigation measures based on field observation and suggests for appropriate structures and their designs. The main objective of the field assessment of the landslides is to assist the implementing agency (department of roads), to finalize quick remedial measures to open the traffic and provide adequate data and information for future structural design to mitigate the effects of landslides. The main findings of this assessment are: i) The designed slope protection structures (gabion retaining wall and breast walls) are not properly founded on the firm base; ii) The backfill materials are not compacted well iii) The provision of drainage structures are inadequate and most of them became non functional during monsoon period due to lack of regular cleaning of debris; iv) The most of landslides occurred on the northern aspects having moist soil and dense vegetation coverage; v) There is lack of proper water management in design of road alignment and vi) Soil bioengineering techniques to stabilize cut slopes are not implemented properly. The result of this assessment shows that, proper care should be given in design while designing a road on hills and mountains with fragile geology and heavy Monsoon rain. Similarly, due consideration should be given during construction also to minimize the damages of structures during monsoon and to avoid frequent road closures and reduce the number and extent of possible landslides.

On the Design of Smart Homes: A Framework for Activity Recognition in Home Environment.

PubMed

Cicirelli, Franco; Fortino, Giancarlo; Giordano, Andrea; Guerrieri, Antonio; Spezzano, Giandomenico; Vinci, Andrea

2016-09-01

A smart home is a home environment enriched with sensing, actuation, communication and computation capabilities which permits to adapt it to inhabitants preferences and requirements. Establishing a proper strategy of actuation on the home environment can require complex computational tasks on the sensed data. This is the case of activity recognition, which consists in retrieving high-level knowledge about what occurs in the home environment and about the behaviour of the inhabitants. The inherent complexity of this application domain asks for tools able to properly support the design and implementation phases. This paper proposes a framework for the design and implementation of smart home applications focused on activity recognition in home environments. The framework mainly relies on the Cloud-assisted Agent-based Smart home Environment (CASE) architecture offering basic abstraction entities which easily allow to design and implement Smart Home applications. CASE is a three layered architecture which exploits the distributed multi-agent paradigm and the cloud technology for offering analytics services. Details about how to implement activity recognition onto the CASE architecture are supplied focusing on the low-level technological issues as well as the algorithms and the methodologies useful for the activity recognition. The effectiveness of the framework is shown through a case study consisting of a daily activity recognition of a person in a home environment.

Evaluating the performance of two neutron spectrum unfolding codes based on iterative procedures and artificial neural networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortiz-Rodriguez, J. M.; Reyes Alfaro, A.; Reyes Haro, A.

In this work the performance of two neutron spectrum unfolding codes based on iterative procedures and artificial neural networks is evaluated. The first one code based on traditional iterative procedures and called Neutron spectrometry and dosimetry from the Universidad Autonoma de Zacatecas (NSDUAZ) use the SPUNIT iterative algorithm and was designed to unfold neutron spectrum and calculate 15 dosimetric quantities and 7 IAEA survey meters. The main feature of this code is the automated selection of the initial guess spectrum trough a compendium of neutron spectrum compiled by the IAEA. The second one code known as Neutron spectrometry and dosimetrymore » with artificial neural networks (NDSann) is a code designed using neural nets technology. The artificial intelligence approach of neural net does not solve mathematical equations. By using the knowledge stored at synaptic weights on a neural net properly trained, the code is capable to unfold neutron spectrum and to simultaneously calculate 15 dosimetric quantities, needing as entrance data, only the rate counts measured with a Bonner spheres system. Similarities of both NSDUAZ and NSDann codes are: they follow the same easy and intuitive user's philosophy and were designed in a graphical interface under the LabVIEW programming environment. Both codes unfold the neutron spectrum expressed in 60 energy bins, calculate 15 dosimetric quantities and generate a full report in HTML format. Differences of these codes are: NSDUAZ code was designed using classical iterative approaches and needs an initial guess spectrum in order to initiate the iterative procedure. In NSDUAZ, a programming routine was designed to calculate 7 IAEA instrument survey meters using the fluence-dose conversion coefficients. NSDann code use artificial neural networks for solving the ill-conditioned equation system of neutron spectrometry problem through synaptic weights of a properly trained neural network. Contrary to iterative procedures, in neural net approach it is possible to reduce the rate counts used to unfold the neutron spectrum. To evaluate these codes a computer tool called Neutron Spectrometry and dosimetry computer tool was designed. The results obtained with this package are showed. The codes here mentioned are freely available upon request to the authors.« less

Evaluating the performance of two neutron spectrum unfolding codes based on iterative procedures and artificial neural networks

NASA Astrophysics Data System (ADS)

Ortiz-Rodríguez, J. M.; Reyes Alfaro, A.; Reyes Haro, A.; Solís Sánches, L. O.; Miranda, R. Castañeda; Cervantes Viramontes, J. M.; Vega-Carrillo, H. R.

2013-07-01

In this work the performance of two neutron spectrum unfolding codes based on iterative procedures and artificial neural networks is evaluated. The first one code based on traditional iterative procedures and called Neutron spectrometry and dosimetry from the Universidad Autonoma de Zacatecas (NSDUAZ) use the SPUNIT iterative algorithm and was designed to unfold neutron spectrum and calculate 15 dosimetric quantities and 7 IAEA survey meters. The main feature of this code is the automated selection of the initial guess spectrum trough a compendium of neutron spectrum compiled by the IAEA. The second one code known as Neutron spectrometry and dosimetry with artificial neural networks (NDSann) is a code designed using neural nets technology. The artificial intelligence approach of neural net does not solve mathematical equations. By using the knowledge stored at synaptic weights on a neural net properly trained, the code is capable to unfold neutron spectrum and to simultaneously calculate 15 dosimetric quantities, needing as entrance data, only the rate counts measured with a Bonner spheres system. Similarities of both NSDUAZ and NSDann codes are: they follow the same easy and intuitive user's philosophy and were designed in a graphical interface under the LabVIEW programming environment. Both codes unfold the neutron spectrum expressed in 60 energy bins, calculate 15 dosimetric quantities and generate a full report in HTML format. Differences of these codes are: NSDUAZ code was designed using classical iterative approaches and needs an initial guess spectrum in order to initiate the iterative procedure. In NSDUAZ, a programming routine was designed to calculate 7 IAEA instrument survey meters using the fluence-dose conversion coefficients. NSDann code use artificial neural networks for solving the ill-conditioned equation system of neutron spectrometry problem through synaptic weights of a properly trained neural network. Contrary to iterative procedures, in neural net approach it is possible to reduce the rate counts used to unfold the neutron spectrum. To evaluate these codes a computer tool called Neutron Spectrometry and dosimetry computer tool was designed. The results obtained with this package are showed. The codes here mentioned are freely available upon request to the authors.

Design and analysis of coherent OCDM en/decoder based on photonic crystal

NASA Astrophysics Data System (ADS)

Zhang, Chongfu; Qiu, Kun

2008-08-01

The design and performance analysis of a new coherent optical en/decoder based on photonic crystal (PhC) for optical code -division -multiple (OCDM) are presented in this paper. In this scheme, the optical pulse phase and time delay can be flexibly controlled by photonic crystal phase shifter and time delayer by using the appropriate design of fabrication. According to the PhC transmission matrix theorem, combination calculation of the impurity and normal period layers is applied, and performances of the PhC-based optical en/decoder are also analyzed. The reflection, transmission, time delay characteristic and optical spectrum of pulse en/decoded are studied for the waves tuned in the photonic band-gap by numerical calculation. Theoretical analysis and numerical results indicate that the optical pulse is achieved to properly phase modulation and time delay, and an auto-correlation of about 8 dB ration and cross-correlation is gained, which demonstrates the applicability of true pulse phase modulation in a number of applications.

FAME, a microprocessor based front-end analysis and modeling environment

NASA Technical Reports Server (NTRS)

Rosenbaum, J. D.; Kutin, E. B.

1980-01-01

Higher order software (HOS) is a methodology for the specification and verification of large scale, complex, real time systems. The HOS methodology was implemented as FAME (front end analysis and modeling environment), a microprocessor based system for interactively developing, analyzing, and displaying system models in a low cost user-friendly environment. The nature of the model is such that when completed it can be the basis for projection to a variety of forms such as structured design diagrams, Petri-nets, data flow diagrams, and PSL/PSA source code. The user's interface with the analyzer is easily recognized by any current user of a structured modeling approach; therefore extensive training is unnecessary. Furthermore, when all the system capabilities are used one can check on proper usage of data types, functions, and control structures thereby adding a new dimension to the design process that will lead to better and more easily verified software designs.

Earthquake Damping Device for Steel Frame

NASA Astrophysics Data System (ADS)

Zamri Ramli, Mohd; Delfy, Dezoura; Adnan, Azlan; Torman, Zaida

2018-04-01

Structures such as buildings, bridges and towers are prone to collapse when natural phenomena like earthquake occurred. Therefore, many design codes are reviewed and new technologies are introduced to resist earthquake energy especially on building to avoid collapse. The tuned mass damper is one of the earthquake reduction products introduced on structures to minimise the earthquake effect. This study aims to analyse the effectiveness of tuned mass damper by experimental works and finite element modelling. The comparisons are made between these two models under harmonic excitation. Based on the result, it is proven that installing tuned mass damper will reduce the dynamic response of the frame but only in several input frequencies. At the highest input frequency applied, the tuned mass damper failed to reduce the responses. In conclusion, in order to use a proper design of damper, detailed analysis must be carried out to have sufficient design based on the location of the structures with specific ground accelerations.

Grid-connected in-stream hydroelectric generation based on the doubly fed induction machine

NASA Astrophysics Data System (ADS)

Lenberg, Timothy J.

Within the United States, there is a growing demand for new environmentally friendly power generation. This has led to a surge in wind turbine development. Unfortunately, wind is not a stable prime mover, but water is. Why not apply the advances made for wind to in-stream hydroelectric generation? One important advancement is the creation of the Doubly Fed Induction Machine (DFIM). This thesis covers the application of a gearless DFIM topology for hydrokinetic generation. After providing background, this thesis presents many of the options available for the mechanical portion of the design. A mechanical turbine is then specified. Next, a method is presented for designing a DFIM including the actual design for this application. In Chapter 4, a simulation model of the system is presented, complete with a control system that maximizes power generation based on water speed. This section then goes on to present simulation results demonstrating proper operation.

Base Station Activation and Linear Transceiver Design for Optimal Resource Management in Heterogeneous Networks

NASA Astrophysics Data System (ADS)

Liao, Wei-Cheng; Hong, Mingyi; Liu, Ya-Feng; Luo, Zhi-Quan

2014-08-01

In a densely deployed heterogeneous network (HetNet), the number of pico/micro base stations (BS) can be comparable with the number of the users. To reduce the operational overhead of the HetNet, proper identification of the set of serving BSs becomes an important design issue. In this work, we show that by jointly optimizing the transceivers and determining the active set of BSs, high system resource utilization can be achieved with only a small number of BSs. In particular, we provide formulations and efficient algorithms for such joint optimization problem, under the following two common design criteria: i) minimization of the total power consumption at the BSs, and ii) maximization of the system spectrum efficiency. In both cases, we introduce a nonsmooth regularizer to facilitate the activation of the most appropriate BSs. We illustrate the efficiency and the efficacy of the proposed algorithms via extensive numerical simulations.

Design of Neural Networks for Fast Convergence and Accuracy: Dynamics and Control

NASA Technical Reports Server (NTRS)

Maghami, Peiman G.; Sparks, Dean W., Jr.

1997-01-01

A procedure for the design and training of artificial neural networks, used for rapid and efficient controls and dynamics design and analysis for flexible space systems, has been developed. Artificial neural networks are employed, such that once properly trained, they provide a means of evaluating the impact of design changes rapidly. Specifically, two-layer feedforward neural networks are designed to approximate the functional relationship between the component/spacecraft design changes and measures of its performance or nonlinear dynamics of the system/components. A training algorithm, based on statistical sampling theory, is presented, which guarantees that the trained networks provide a designer-specified degree of accuracy in mapping the functional relationship. Within each iteration of this statistical-based algorithm, a sequential design algorithm is used for the design and training of the feedforward network to provide rapid convergence to the network goals. Here, at each sequence a new network is trained to minimize the error of previous network. The proposed method should work for applications wherein an arbitrary large source of training data can be generated. Two numerical examples are performed on a spacecraft application in order to demonstrate the feasibility of the proposed approach.

Design of neural networks for fast convergence and accuracy: dynamics and control.

PubMed

Maghami, P G; Sparks, D R

2000-01-01

A procedure for the design and training of artificial neural networks, used for rapid and efficient controls and dynamics design and analysis for flexible space systems, has been developed. Artificial neural networks are employed, such that once properly trained, they provide a means of evaluating the impact of design changes rapidly. Specifically, two-layer feedforward neural networks are designed to approximate the functional relationship between the component/spacecraft design changes and measures of its performance or nonlinear dynamics of the system/components. A training algorithm, based on statistical sampling theory, is presented, which guarantees that the trained networks provide a designer-specified degree of accuracy in mapping the functional relationship. Within each iteration of this statistical-based algorithm, a sequential design algorithm is used for the design and training of the feedforward network to provide rapid convergence to the network goals. Here, at each sequence a new network is trained to minimize the error of previous network. The proposed method should work for applications wherein an arbitrary large source of training data can be generated. Two numerical examples are performed on a spacecraft application in order to demonstrate the feasibility of the proposed approach.

Improved Simulations of Astrophysical Plasmas: Computation of New Atomic Data

NASA Technical Reports Server (NTRS)

Gorczyca, Thomas W.; Korista, Kirk T.

2005-01-01

Our research program is designed to carry out state-of-the-art atomic physics calculations crucial to advancing our understanding of fundamental astrophysical problems. We redress the present inadequacies in the atomic data base along two important areas: dielectronic recombination and inner-shell photoionization and multiple electron ejection/Auger fluorescence therefrom. All of these data are disseminated to the astrophysical community in the proper format for implementation in spectral simulation code.

Under Voltage Lock-Out Design Rules for Proper Start-Up of Energy Autonomous Systems Powered by Supercapacitors

NASA Astrophysics Data System (ADS)

Boitier, V.; Durand Estèbe, P.; Monthéard, R.; Bafleur, M.; Dilhac, J. M.

2013-12-01

This paper deals with the issue of the initial start-up of an autonomous and battery-free system powered by an energy harvester associated with a storage subsystem based on supercapacitors initially discharged. A review of different low power Under Voltage Lock-Out (UVLO) solutions used to delay the load start-up and to avoid a useless discharge of supercapacitors is presented and discussed.

Real-time PCR (qPCR) primer design using free online software.

PubMed

Thornton, Brenda; Basu, Chhandak

2011-01-01

Real-time PCR (quantitative PCR or qPCR) has become the preferred method for validating results obtained from assays which measure gene expression profiles. The process uses reverse transcription polymerase chain reaction (RT-PCR), coupled with fluorescent chemistry, to measure variations in transcriptome levels between samples. The four most commonly used fluorescent chemistries are SYBR® Green dyes and TaqMan®, Molecular Beacon or Scorpion probes. SYBR® Green is very simple to use and cost efficient. As SYBR® Green dye binds to any double-stranded DNA product, its success depends greatly on proper primer design. Many types of online primer design software are available, which can be used free of charge to design desirable SYBR® Green-based qPCR primers. This laboratory exercise is intended for those who have a fundamental background in PCR. It addresses the basic fluorescent chemistries of real-time PCR, the basic rules and pitfalls of primer design, and provides a step-by-step protocol for designing SYBR® Green-based primers with free, online software. Copyright © 2010 Wiley Periodicals, Inc.

Wave simulation for the design of an innovative quay wall: the case of Vlorë Harbour

NASA Astrophysics Data System (ADS)

Antonini, Alessandro; Archetti, Renata; Lamberti, Alberto

2017-01-01

Sea states and environmental conditions are basic data for the design of marine structures. Hindcasted wave data have been applied here with the aim of identifying the proper design conditions for an innovative quay wall concept. In this paper, the results of a computational fluid dynamics model are used to optimise the new absorbing quay wall of Vlorë Harbour (Republic of Albania) and define the design loads under extreme wave conditions. The design wave states at the harbour entrance have been estimated analysing 31 years of hindcasted wave data simulated through the application of WaveWatch III. Due to the particular geography and topography of the Bay of Vlorë, wave conditions generated from the north-west are transferred to the harbour entrance with the application of a 2-D spectral wave module, whereas southern wave states, which are also the most critical for the port structures, are defined by means of a wave generation model, according to the available wind measurements. Finally, the identified extreme events have been used, through the NewWave approach, as boundary conditions for the numerical analysis of the interaction between the quay wall and the extreme events. The results show that the proposed method, based on numerical modelling at different scales from macro to meso and to micro, allows for the identification of the best site-specific solutions, also for a location devoid of any wave measurement. In this light, the objectives of the paper are two-fold. First, they show the application of sea condition estimations through the use of wave hindcasted data in order to properly define the design wave conditions for a new harbour structure. Second, they present a new approach for investigating an innovative absorbing quay wall based on CFD modelling and the NewWave theory.

Design and Testing of Space Telemetry SCA Waveform

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Handler, Louis M.; Quinn, Todd M.

2006-01-01

A Software Communications Architecture (SCA) Waveform for space telemetry is being developed at the NASA Glenn Research Center (GRC). The space telemetry waveform is implemented in a laboratory testbed consisting of general purpose processors, field programmable gate arrays (FPGAs), analog-to-digital converters (ADCs), and digital-to-analog converters (DACs). The radio hardware is integrated with an SCA Core Framework and other software development tools. The waveform design is described from both the bottom-up signal processing and top-down software component perspectives. Simulations and model-based design techniques used for signal processing subsystems are presented. Testing with legacy hardware-based modems verifies proper design implementation and dynamic waveform operations. The waveform development is part of an effort by NASA to define an open architecture for space based reconfigurable transceivers. Use of the SCA as a reference has increased understanding of software defined radio architectures. However, since space requirements put a premium on size, mass, and power, the SCA may be impractical for today s space ready technology. Specific requirements for an SCA waveform and other lessons learned from this development are discussed.

SDRE controller for motion design of cable-suspended robot with uncertainties and moving obstacles

NASA Astrophysics Data System (ADS)

Behboodi, Ahad; Salehi, Seyedmohammad

2017-10-01

In this paper an optimal control approach for nonlinear dynamical systems was proposed based on State Dependent Riccati Equation (SDRE) and its robustness against uncertainties is shown by simulation results. The proposed method was applied on a spatial six-cable suspended robot, which was designed to carry loads or perform different tasks in huge workspaces. Motion planning for cable-suspended robots in such a big workspace is subjected to uncertainties and obstacles. First, we emphasized the ability of SDRE to construct a systematic basis and efficient design of controller for wide variety of nonlinear dynamical systems. Then we showed how this systematic design improved the robustness of the system and facilitated the integration of motion planning techniques with the controller. In particular, obstacle avoidance technique based on artificial potential field (APF) can be easily combined with SDRE controller with efficient performance. Due to difficulties of exact solution for SDRE, an approximation method was used based on power series expansion. The efficiency and robustness of the SDRE controller was illustrated on a six-cable suspended robot with proper simulations.

Gadolinium-Based Contrast Agents for MR Cancer Imaging

PubMed Central

Zhou, Zhuxian; Lu, Zheng-Rong

2013-01-01

Magnetic resonance imaging (MRI) is a clinical imaging modality effective for anatomical and functional imaging of diseased soft tissues, including solid tumors. MRI contrast agents have been routinely used for detecting tumor at an early stage. Gadolinium based contrast agents are the most commonly used contrast agents in clinical MRI. There have been significant efforts to design and develop novel Gd(III) contrast agents with high relaxivity, low toxicity and specific tumor binding. The relaxivity of the Gd(III) contrast agents can be increased by proper chemical modification. The toxicity of Gd(III) contrast agents can be reduced by increasing the agents’ thermodynamic and kinetic stability, as well as optimizing their pharmacokinetic properties. The increasing knowledge in the field of cancer genomics and biology provides an opportunity for designing tumor-specific contrast agents. Various new Gd(III) chelates have been designed and evaluated in animal models for more effective cancer MRI. This review outlines the design and development, physicochemical properties, and in vivo properties of several classes of Gd(III)-based MR contrast agents for tumor imaging. PMID:23047730

APPLICATION OF STEEL PIPE PILE LOADING TESTS TO DESIGN VERIFICATION OF FOUNDATION OF THE TOKYO GATE BRIDGE

NASA Astrophysics Data System (ADS)

Saitou, Yutaka; Kikuchi, Yoshiaki; Kusakabe, Osamu; Kiyomiya, Osamu; Yoneyama, Haruo; Kawakami, Taiji

Steel sheet pipe pile foundations with large diameter steel pipe sheet pile were used for the foundation of the main pier of the Tokyo Gateway bridge. However, as for the large diameter steel pipe pile, the bearing mechanism including a pile tip plugging effect is still unclear due to lack of the practical examinations even though loading tests are performed on Trans-Tokyo Bay Highway. In the light of the foregoing problems, static pile loading tests both vertical and horizontal directions, a dynamic loading test, and cone penetration tests we re conducted for determining proper design parameters of the ground for the foundations. Design parameters were determined rationally based on the tests results. Rational design verification was obtained from this research.

Start-up and Self-sustain Test of 500 W Ultra-Micro Gas Turbine Generator

NASA Astrophysics Data System (ADS)

Seo, Jeong Min; Park, Jun Young; Seog Choi, Bum

2013-12-01

This paper provides the performance test for start-up and self-sustaining of 500W ultra-micro gas turbine (UMGT) generator. Each component of UMGT, a centrifugal compressor, a radial turbine, an annular combustor and a shaft is already designed, manufactured and tested to meet design requirements in previous researches. However, they are not tested to work in an integrate system. Currently, integrated test unit with a compressor, a combustor and a turbine, is developed to find the proper condition of start-up and self-sustain. Ignition sequence depending on rotating speed is designed. Performance test for start-up and self-sustain is designed based on the ignition possible condition. An air impingement starter and a hot bulb inginer are applied. LPG is used as main fuel.

Frequency wavenumber design of spiral macro fiber composite directional transducers

NASA Astrophysics Data System (ADS)

Carrara, Matteo; Ruzzene, Massimo

2015-04-01

This work is focused on design and testing of a novel class of transducers for Structural Health Monitoring (SHM), able to perform directional interrogation of plate-like structures. These transducers leverage guided waves (GWs), and in particular Lamb waves, that have emerged as a very prominent option for assessing the state of a structure during operation. GW-SHM approaches greatly benefit from the use of transducers with controllable directional characteristics, so that selective scanning of a surface can be performed to locate damage, impacts, or cracks. In the concepts that we propose, continuous beam steering and directional actuation are achieved through proper selection of the excitation frequency. The design procedure takes advantage of the wavenumber representation of the device, and formulates the problem using a Fourier-based approach. The active layer of the transducer is made of piezoelectric fibers embedded into an epoxy matrix, allowing the device to be flexible, and thus suitable for application on non{ at surfaces. Proper shaping of the electrodes pattern through a compensation function allows taking into account the anisotropy level introduced by the active layer. The resulting spiral frequency steerable acoustic actuator is a configuration that features (i) enhanced performance, (ii) reduced complexity, and (iii) reduced hardware requirements of such devices.

PCB-Based Break-Out Box

NASA Technical Reports Server (NTRS)

Lee, Jason H.

2011-01-01

Break-out boxes (BOBs) are necessary for all electrical integration/cable checkouts and troubleshooting. Because the price of a BOB is high, and no work can be done without one, often the procedure stops, simply waiting for a BOB. A less expensive BOB would take less time in the integration, testing, and troubleshooting process. The PCB-based BOB works and looks the same as a standard JPL BOB, called Gold Boxes. The only differences between the old BOB and the new PCB-based BOB is that the new one has 80 percent of its circuitry in a printed circuit board. This process reduces the time for fabrication, thus making the BOBs less expensive. Moreover, because of its unique design, the new BOBs can be easily assembled and fixed. About 80 percent of the new PCB-based BOB is in a $22 (at the time of this reporting) custom-designed, yet commercially available PCB. This device has been used successfully to verify that BOB cables were properly made. Also, upon completion, the BOB was beeped out via a multimeter to ensure that all sockets on the connectors were properly connected to the respective banana jack. When compared to the Gold Box BOBs, the new BOB has many advantages. It is much more cost efficient, it delivers equal usability at substantially lower cost of the BOB, and the Gold Box is much heavier when compared to the new BOB. The new BOB is also a bit longer and much more versatile in that connectors are easily changeable and if a banana jack is broken, it can be replaced instead of throwing away an entire BOB.

Design, parametrization, and pole placement of stabilizing output feedback compensators via injective cogenerator quotient signal modules.

PubMed

Blumthaler, Ingrid; Oberst, Ulrich

2012-03-01

Control design belongs to the most important and difficult tasks of control engineering and has therefore been treated by many prominent researchers and in many textbooks, the systems being generally described by their transfer matrices or by Rosenbrock equations and more recently also as behaviors. Our approach to controller design uses, in addition to the ideas of our predecessors on coprime factorizations of transfer matrices and on the parametrization of stabilizing compensators, a new mathematical technique which enables simpler design and also new theorems in spite of the many outstanding results of the literature: (1) We use an injective cogenerator signal module ℱ over the polynomial algebra [Formula: see text] (F an infinite field), a saturated multiplicatively closed set T of stable polynomials and its quotient ring [Formula: see text] of stable rational functions. This enables the simultaneous treatment of continuous and discrete systems and of all notions of stability, called T-stability. We investigate stabilizing control design by output feedback of input/output (IO) behaviors and study the full feedback IO behavior, especially its autonomous part and not only its transfer matrix. (2) The new technique is characterized by the permanent application of the injective cogenerator quotient signal module [Formula: see text] and of quotient behaviors [Formula: see text] of [Formula: see text]-behaviors B. (3) For the control tasks of tracking, disturbance rejection, model matching, and decoupling and not necessarily proper plants we derive necessary and sufficient conditions for the existence of proper stabilizing compensators with proper and stable closed loop behaviors, parametrize all such compensators as IO behaviors and not only their transfer matrices and give new algorithms for their construction. Moreover we solve the problem of pole placement or spectral assignability for the complete feedback behavior. The properness of the full feedback behavior ensures the absence of impulsive solutions in the continuous case, and that of the compensator enables its realization by Kalman state space equations or elementary building blocks. We note that every behavior admits an IO decomposition with proper transfer matrix, but that most of these decompositions do not have this property, and therefore we do not assume the properness of the plant. (4) The new technique can also be applied to more general control interconnections according to Willems, in particular to two-parameter feedback compensators and to the recent tracking framework of Fiaz/Takaba/Trentelman. In contrast to these authors, however, we pay special attention to the properness of all constructed transfer matrices which requires more subtle algorithms.

WebAlchemist: a Web transcoding system for mobile Web access in handheld devices

NASA Astrophysics Data System (ADS)

Whang, Yonghyun; Jung, Changwoo; Kim, Jihong; Chung, Sungkwon

2001-11-01

In this paper, we describe the design and implementation of WebAlchemist, a prototype web transcoding system, which automatically converts a given HTML page into a sequence of equivalent HTML pages that can be properly displayed on a hand-held device. The Web/Alchemist system is based on a set of HTML transcoding heuristics managed by the Transcoding Manager (TM) module. In order to tackle difficult-to-transcode pages such as ones with large or complex table structures, we have developed several new transcoding heuristics that extract partial semantics from syntactic information such as the table width, font size and cascading style sheet. Subjective evaluation results using popular HTML pages (such as the CNN home page) show that WebAlchemist generates readable, structure-preserving transcoded pages, which can be properly displayed on hand-held devices.

AHP based Anthropometric Analysis of University Hall Bed Design in Bangladesh

NASA Astrophysics Data System (ADS)

Halder, Pobitra; Sarker, Eity; Karmaker, Chitralekha

2018-05-01

In university hall, different types of bed are used for providing sleeping environment to the students. Although there are wide variations in the design of students' bed in Bangladeshi university hall, none of them are designed properly considering the anthropometric data. In this study, four anthropometric measurements related to normal students' bed dimensions were measured from 300 students from a public university hall in Bangladesh. The feedbacks regarding different health problems and their reasons were collected from considering practical situations of the students and gathering experts' opinions. Chi-square test showed that back pain, blood circulation problem, fatigue, comfort, and sleeping problem are related to students' anthropometric measurements. The analytic hierarchy process (AHP) analysis identified students' bed length as the most responsible attribute for ergonomic problems of the students. Finally, the linear regression and correlation analysis suggested the bed dimensions based on stature of the students. This study can be a helpful guideline for industrial engineers and manufacturers in designing more comfortable students' bed.

Image Geometric Corrections for a New EMCCD-based Dual Modular X-ray Imager

PubMed Central

Qu, Bin; Huang, Ying; Wang, Weiyuan; Cartwright, Alexander N.; Titus, Albert H.; Bednarek, Daniel R.; Rudin, Stephen

2012-01-01

An EMCCD-based dual modular x-ray imager was recently designed and developed from the component level, providing a high dynamic range of 53 dB and an effective pixel size of 26 μm for angiography and fluoroscopy. The unique 2×1 array design efficiently increased the clinical field of view, and also can be readily expanded to an M×N array implementation. Due to the alignment mismatches between the EMCCD sensors and the fiber optic tapers in each module, the output images or video sequences result in a misaligned 2048×1024 digital display if uncorrected. In this paper, we present a method for correcting display registration using a custom-designed two layer printed circuit board. This board was designed with grid lines to serve as the calibration pattern, and provides an accurate reference and sufficient contrast to enable proper display registration. Results show an accurate and fine stitching of the two outputs from the two modules. PMID:22254882

Design of Critical Components

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.; Zaretsky, Erwin V.

2001-01-01

Critical component design is based on minimizing product failures that results in loss of life. Potential catastrophic failures are reduced to secondary failures where components removed for cause or operating time in the system. Issues of liability and cost of component removal become of paramount importance. Deterministic design with factors of safety and probabilistic design address but lack the essential characteristics for the design of critical components. In deterministic design and fabrication there are heuristic rules and safety factors developed over time for large sets of structural/material components. These factors did not come without cost. Many designs failed and many rules (codes) have standing committees to oversee their proper usage and enforcement. In probabilistic design, not only are failures a given, the failures are calculated; an element of risk is assumed based on empirical failure data for large classes of component operations. Failure of a class of components can be predicted, yet one can not predict when a specific component will fail. The analogy is to the life insurance industry where very careful statistics are book-kept on classes of individuals. For a specific class, life span can be predicted within statistical limits, yet life-span of a specific element of that class can not be predicted.

Traditional versus rule-based programming techniques: Application to the control of optional flight information

NASA Technical Reports Server (NTRS)

Ricks, Wendell R.; Abbott, Kathy H.

1987-01-01

To the software design community, the concern over the costs associated with a program's execution time and implementation is great. It is always desirable, and sometimes imperative, that the proper programming technique is chosen which minimizes all costs for a given application or type of application. A study is described that compared cost-related factors associated with traditional programming techniques to rule-based programming techniques for a specific application. The results of this study favored the traditional approach regarding execution efficiency, but favored the rule-based approach regarding programmer productivity (implementation ease). Although this study examined a specific application, the results should be widely applicable.

Digital design of scaffold for mandibular defect repair based on tissue engineering*

PubMed Central

Liu, Yun-feng; Zhu, Fu-dong; Dong, Xing-tao; Peng, Wei

2011-01-01

Mandibular defect occurs more frequently in recent years, and clinical repair operations via bone transplantation are difficult to be further improved due to some intrinsic flaws. Tissue engineering, which is a hot research field of biomedical engineering, provides a new direction for mandibular defect repair. As the basis and key part of tissue engineering, scaffolds have been widely and deeply studied in regards to the basic theory, as well as the principle of biomaterial, structure, design, and fabrication method. However, little research is targeted at tissue regeneration for clinic repair operations. Since mandibular bone has a special structure, rather than uniform and regular structure in existing studies, a methodology based on tissue engineering is proposed for mandibular defect repair in this paper. Key steps regarding scaffold digital design, such as external shape design and internal microstructure design directly based on triangular meshes are discussed in detail. By analyzing the theoretical model and the measured data from the test parts fabricated by rapid prototyping, the feasibility and effectiveness of the proposed methodology are properly verified. More works about mechanical and biological improvements need to be done to promote its clinical application in future. PMID:21887853

Digital design of scaffold for mandibular defect repair based on tissue engineering.

PubMed

Liu, Yun-feng; Zhu, Fu-dong; Dong, Xing-tao; Peng, Wei

2011-09-01

Mandibular defect occurs more frequently in recent years, and clinical repair operations via bone transplantation are difficult to be further improved due to some intrinsic flaws. Tissue engineering, which is a hot research field of biomedical engineering, provides a new direction for mandibular defect repair. As the basis and key part of tissue engineering, scaffolds have been widely and deeply studied in regards to the basic theory, as well as the principle of biomaterial, structure, design, and fabrication method. However, little research is targeted at tissue regeneration for clinic repair operations. Since mandibular bone has a special structure, rather than uniform and regular structure in existing studies, a methodology based on tissue engineering is proposed for mandibular defect repair in this paper. Key steps regarding scaffold digital design, such as external shape design and internal microstructure design directly based on triangular meshes are discussed in detail. By analyzing the theoretical model and the measured data from the test parts fabricated by rapid prototyping, the feasibility and effectiveness of the proposed methodology are properly verified. More works about mechanical and biological improvements need to be done to promote its clinical application in future.

Safe Youth. Safe Schools.

MedlinePlus

... evidence. Research/Data Sources Crime Prevention Through Environmental Design (CPTED) School Project Research has shown that proper environmental design can reduce crime and fear associated with criminal ...

Orientation-Dependent Exciton-Plasmon Coupling in Embedded Organic/Metal Nanowire Heterostructures.

PubMed

Li, Yong Jun; Hong, Yan; Peng, Qian; Yao, Jiannian; Zhao, Yong Sheng

2017-10-24

The excitation of surface plasmons by optical emitters based on exciton-plasmon coupling is important for plasmonic devices with active optical properties. It has been theoretically demonstrated that the orientation of exciton dipole can significantly influence the coupling strength, yet systematic study of the coupling process in nanostructures is still hindered by the lack of proper material systems. In this work, we have experimentally investigated the orientation-dependent exciton-plasmon coupling in a rationally designed organic/metal nanowire heterostructure system. The heterostructures were prepared by inserting silver nanowires into crystalline organic waveguides during the self-assembly of dye molecules. Structures with different exciton orientations exhibited varying coupling efficiencies. The near-field exciton-plasmon coupling facilitates the design of nanophotonic devices based on the directional surface plasmon polariton propagations.

Engineering molecular machines

NASA Astrophysics Data System (ADS)

Erman, Burak

2016-04-01

Biological molecular motors use chemical energy, mostly in the form of ATP hydrolysis, and convert it to mechanical energy. Correlated thermal fluctuations are essential for the function of a molecular machine and it is the hydrolysis of ATP that modifies the correlated fluctuations of the system. Correlations are consequences of the molecular architecture of the protein. The idea that synthetic molecular machines may be constructed by designing the proper molecular architecture is challenging. In their paper, Sarkar et al (2016 New J. Phys. 18 043006) propose a synthetic molecular motor based on the coarse grained elastic network model of proteins and show by numerical simulations that motor function is realized, ranging from deterministic to thermal, depending on temperature. This work opens up a new range of possibilities of molecular architecture based engine design.

Scanning Kirkpatrick-Baez X-ray telescope to maximize effective area and eliminate spurious images - Design

NASA Technical Reports Server (NTRS)

Kast, J. W.

1975-01-01

We consider the design of a Kirkpatrick-Baez grazing-incidence X-ray telescope to be used in a scan of the sky and analyze the distribution of both properly reflected rays and spurious images over the field of view. To obtain maximum effective area over the field of view, it is necessary to increase the spacing between plates for a scanning telescope as compared to a pointing telescope. Spurious images are necessarily present in this type of lens, but they can be eliminated from the field of view by adding properly located baffles or collimators. Results of a computer design are presented.

Design of an Integrated Thermoelectric Generator Power Converter for Ultra-Low Power and Low Voltage Body Energy Harvesters aimed at EEG/ECG Active Electrodes

NASA Astrophysics Data System (ADS)

Ataei, Milad; Robert, Christian; Boegli, Alexis; Farine, Pierre-André

2014-11-01

This paper describes a design procedure for an efficient body thermal energy harvesting integrated power converter. This procedure is based on loss examination for a selfpowered medical device. All optimum system parameters are calculated respecting the transducer constraints and the application form factor. It is found that it is possible to optimize converter's working frequency with proper design of its pulse generator circuit. At selected frequency, it has been demonstrated that wide area voltage doubler can be eliminated at the expense of wider switches. With this method, more than 60% efficiency is achieved in simulation for just 20mV transducer output voltage and 30% of entire chip area is saved.

Strategic sensor locations of FPR bridge decks

NASA Astrophysics Data System (ADS)

Wu, Hwai-Chung; Warnemuende, Kraig; Yan, An; Mu, Bin

2003-07-01

Advanced fiber-reinforced polymer composite (FRP) has been increasingly used in bridge deck to replace concrete or steel. A FRP bridge deck can be designed to meet AASHTO HS-25 load requirements. FRP decks have many advantages over the conventional reinforced concrete or steel decks owing to their lightweight, high strength and corrosion resistance. However, such new deck system requires extensive monitoring to ensure its designed performance before its widespread acceptance by the bridge community. For inspection and evaluation purpose, a proper monitoring system consisting of various kinds of sensors installed in the FRP deck is critical. This paper provides a framework for designing an efficient monitoring system. The strategic sensor locations are identified based on the stress analysis of the FRP deck.

Approaching the design of a failsafe turbine monitor with simple microcontroller blocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zapolin, R.E.

1995-12-31

The proper approach to early instrumentation design for tasks like failsafe turbine monitoring permits meeting requirements without resorting to traditional complex special-purpose electronics. Instead a small network of basic microcontroller building blocks can split the effort with each block optimized for its portion of the overall system. This paper discusses approaching design by partitioning intricate system specifications to permit each block to be optimized to the safety level appropriate for its portion of the overall task while retaining and production and reliability advantages of having common simple modules. It illustrates that approach with a modular microcontroller-based speed monitor which metmore » user needs for the latest in power plant monitoring equipment.« less

Auto-Mechanics Course. Bilingual Vocational Instructional Materials.

ERIC Educational Resources Information Center

Lopez-Cox, Guadalupe

This auto-mechanics course, one of a series of bilingual English-Spanish vocational education courses, is designed to introduce the basic skills that an automotive mechanics student should know. It is geared to teach the student basic manipulative skills, safety judgments, proper work habits, desirable attitudes, and proper behavior for initial…

Minimum-Impact Camping in the Front Woods.

ERIC Educational Resources Information Center

Schatz, Curt

1994-01-01

Minimum-impact camping techniques that can be applied to resident camp programs include controlling group size and behavior, designing camp sites, moving groups frequently, proper use of fires, proper disposal of food and human wastes, use of biodegradable soaps, and encouraging staff and camper awareness of impacts on the environment. (LP)

High Power Microwave (HPM) and Ionizing Radiation Effects on CMOS Devices

DTIC Science & Technology

2010-03-01

24 xviii Symbol Page VIH minimum input voltage for proper high voltage output...38 VOH output voltage corresponding to VIH ...design. The high level at the input, VIH , along with VDD, define the maximum permitted “Logic 1” region, which allows for proper state change for a

Geoexchange: Getting it Right

ERIC Educational Resources Information Center

Johnson, William C.; Ormond, Paul

2013-01-01

If properly installed, optimized geoexchange systems can be one of the most cost effective, powerful options to accomplish the goal of improved energy efficiency and reduced carbon emissions. Accurately quantifying field performance is an important step in designing a system that is the proper size and capacity. The authors share the real life…

36 CFR 1234.10 - What are the facility requirements for all records storage facilities?

Code of Federal Regulations, 2014 CFR

2014-07-01

... the HVAC systems, fire alarm and fire protection systems. Manual switching between sources of service... elements are protected by a properly installed, properly maintained wet-pipe automatic sprinkler system, as... must provide documentation that the facility has a fire suppression system specifically designed to...

Generation and investigation of terahertz Airy beam realized using parallel-plate waveguides

NASA Astrophysics Data System (ADS)

Wu, Mengru; Lang, Tingting; Shi, Guohua; Han, Zhanghua

2018-03-01

In this paper, the launching of Airy beam in the terahertz region using waveguiding structures was proposed, designed and numerically characterized. By properly designing the waveguide slit width and the packing number in different sections of parallel-plate waveguides (PPWGs) array, arbitrary phase delay and lateral position-dependent amplitude transmission through the structure, required to realize the target Airy beam profile, can be easily fulfilled. Airy beams working at the frequency of 0.3 THz with good non-diffracting, self-bending, and self-healing features are demonstrated. This study represents a new alternative to scattering-based metasurface structures, and can be utilized in many modern applications.

Kinematic analysis of the finger exoskeleton using MATLAB/Simulink.

PubMed

Nasiłowski, Krzysztof; Awrejcewicz, Jan; Lewandowski, Donat

2014-01-01

A paralyzed and not fully functional part of human body can be supported by the properly designed exoskeleton system with motoric abilities. It can help in rehabilitation, or movement of a disabled/paralyzed limb. Both suitably selected geometry and specialized software are studied applying the MATLAB environment. A finger exoskeleton was the base for MATLAB/Simulink model. Specialized software, such as MATLAB/Simulink give us an opportunity to optimize calculation reaching precise results, which help in next steps of design process. The calculations carried out yield information regarding movement relation between three functionally connected actuators and showed distance and velocity changes during the whole simulation time.

Variability aware compact model characterization for statistical circuit design optimization

NASA Astrophysics Data System (ADS)

Qiao, Ying; Qian, Kun; Spanos, Costas J.

2012-03-01

Variability modeling at the compact transistor model level can enable statistically optimized designs in view of limitations imposed by the fabrication technology. In this work we propose an efficient variabilityaware compact model characterization methodology based on the linear propagation of variance. Hierarchical spatial variability patterns of selected compact model parameters are directly calculated from transistor array test structures. This methodology has been implemented and tested using transistor I-V measurements and the EKV-EPFL compact model. Calculation results compare well to full-wafer direct model parameter extractions. Further studies are done on the proper selection of both compact model parameters and electrical measurement metrics used in the method.

Optical isolation based on space-time engineered asymmetric photonic band gaps

NASA Astrophysics Data System (ADS)

Chamanara, Nima; Taravati, Sajjad; Deck-Léger, Zoé-Lise; Caloz, Christophe

2017-10-01

Nonreciprocal electromagnetic devices play a crucial role in modern microwave and optical technologies. Conventional methods for realizing such systems are incompatible with integrated circuits. With recent advances in integrated photonics, the need for efficient on-chip magnetless nonreciprocal devices has become more pressing than ever. This paper leverages space-time engineered asymmetric photonic band gaps to generate optical isolation. It shows that a properly designed space-time modulated slab is highly reflective/transparent for opposite directions of propagation. The corresponding design is magnetless, accommodates low modulation frequencies, and can achieve very high isolation levels. An experimental proof of concept at microwave frequencies is provided.

Coach design for the Korean high-speed train: a systematic approach to passenger seat design and layout.

PubMed

Jung, E S; Han, S H; Jung, M; Choe, J

1998-12-01

Proper ergonomic design of a passenger seat and coach layout for a high-speed train is an essential component that is directly related to passenger comfort. In this research, a systematic approach to the design of passenger seats was described and the coach layout which reflected the tradeoff between transportation capacity and passenger comfort was investigated for the Korean high-speed train. As a result, design recommendations and specifications of the passenger seat and its layout were suggested. The whole design process is composed of four stages. A survey and analysis of design requirement was first conducted, which formed the base for designing the first and second class passenger seats. Prototypes were made and evaluated iteratively, and seat arrangement and coach layout were finally obtained. The systematic approach and recommendations suggested in this study are expected to be applicable to the seat design for public transportations and to help modify and redesign existing vehicular seats.

Collaborative Working Architecture for IoT-Based Applications.

PubMed

Mora, Higinio; Signes-Pont, María Teresa; Gil, David; Johnsson, Magnus

2018-05-23

The new sensing applications need enhanced computing capabilities to handle the requirements of complex and huge data processing. The Internet of Things (IoT) concept brings processing and communication features to devices. In addition, the Cloud Computing paradigm provides resources and infrastructures for performing the computations and outsourcing the work from the IoT devices. This scenario opens new opportunities for designing advanced IoT-based applications, however, there is still much research to be done to properly gear all the systems for working together. This work proposes a collaborative model and an architecture to take advantage of the available computing resources. The resulting architecture involves a novel network design with different levels which combines sensing and processing capabilities based on the Mobile Cloud Computing (MCC) paradigm. An experiment is included to demonstrate that this approach can be used in diverse real applications. The results show the flexibility of the architecture to perform complex computational tasks of advanced applications.

Organizational Systems Theory and Command and Control Concepts

DTIC Science & Technology

2013-03-01

Decentralized C2 • Problem is determinable • Many solutions • Predictable results • Low Risk • Slow feedback loop • Plans: Engineered or designed • C2...of these concepts in the Art of Command and the Science of Control, but lacks a proper model to assist commanders in determining how to correctly...commanders in determining how to correctly apply the concepts based on the operational environment. The paper concludes with a recommendation that the

Surface and interface modification science and technology.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, J.-H.

1999-07-19

Surface modification of solids is of scientific and technological interest due to its significant benefits in a wide variety of applications. Various coatings applications such as corrosion protection and electrical insulators and conductors are required for proper engineering design based on geometrical relationships between interfaces and on thermodynamic/kinetic considerations for the development of surface modifications. This paper will explore three basic examples: the proton conductor BaCeO{sub 3}, high-temperature protective coatings, and epitaxial relationships between interfaces.

Iris indexing based on local intensity order pattern

NASA Astrophysics Data System (ADS)

Emerich, Simina; Malutan, Raul; Crisan, Septimiu; Lefkovits, Laszlo

2017-03-01

In recent years, iris biometric systems have increased in popularity and have been proven that are capable of handling large-scale databases. The main advantage of these systems is accuracy and reliability. A proper iris patterns classification is expected to reduce the matching time in huge databases. This paper presents an iris indexing technique based on Local Intensity Order Pattern. The performance of the present approach is evaluated on UPOL database and is compared with other recent systems designed for iris indexing. The results illustrate the potential of the proposed method for large scale iris identification.

Recent mass spectrometry-based techniques and considerations for disulfide bond characterization in proteins.

PubMed

Lakbub, Jude C; Shipman, Joshua T; Desaire, Heather

2018-04-01

Disulfide bonds are important structural moieties of proteins: they ensure proper folding, provide stability, and ensure proper function. With the increasing use of proteins for biotherapeutics, particularly monoclonal antibodies, which are highly disulfide bonded, it is now important to confirm the correct disulfide bond connectivity and to verify the presence, or absence, of disulfide bond variants in the protein therapeutics. These studies help to ensure safety and efficacy. Hence, disulfide bonds are among the critical quality attributes of proteins that have to be monitored closely during the development of biotherapeutics. However, disulfide bond analysis is challenging because of the complexity of the biomolecules. Mass spectrometry (MS) has been the go-to analytical tool for the characterization of such complex biomolecules, and several methods have been reported to meet the challenging task of mapping disulfide bonds in proteins. In this review, we describe the relevant, recent MS-based techniques and provide important considerations needed for efficient disulfide bond analysis in proteins. The review focuses on methods for proper sample preparation, fragmentation techniques for disulfide bond analysis, recent disulfide bond mapping methods based on the fragmentation techniques, and automated algorithms designed for rapid analysis of disulfide bonds from liquid chromatography-MS/MS data. Researchers involved in method development for protein characterization can use the information herein to facilitate development of new MS-based methods for protein disulfide bond analysis. In addition, individuals characterizing biotherapeutics, especially by disulfide bond mapping in antibodies, can use this review to choose the best strategies for disulfide bond assignment of their biologic products. Graphical Abstract This review, describing characterization methods for disulfide bonds in proteins, focuses on three critical components: sample preparation, mass spectrometry data, and software tools.

Relativistic Quantum Metrology: Exploiting relativity to improve quantum measurement technologies

PubMed Central

Ahmadi, Mehdi; Bruschi, David Edward; Sabín, Carlos; Adesso, Gerardo; Fuentes, Ivette

2014-01-01

We present a framework for relativistic quantum metrology that is useful for both Earth-based and space-based technologies. Quantum metrology has been so far successfully applied to design precision instruments such as clocks and sensors which outperform classical devices by exploiting quantum properties. There are advanced plans to implement these and other quantum technologies in space, for instance Space-QUEST and Space Optical Clock projects intend to implement quantum communications and quantum clocks at regimes where relativity starts to kick in. However, typical setups do not take into account the effects of relativity on quantum properties. To include and exploit these effects, we introduce techniques for the application of metrology to quantum field theory. Quantum field theory properly incorporates quantum theory and relativity, in particular, at regimes where space-based experiments take place. This framework allows for high precision estimation of parameters that appear in quantum field theory including proper times and accelerations. Indeed, the techniques can be applied to develop a novel generation of relativistic quantum technologies for gravimeters, clocks and sensors. As an example, we present a high precision device which in principle improves the state-of-the-art in quantum accelerometers by exploiting relativistic effects. PMID:24851858

Relativistic quantum metrology: exploiting relativity to improve quantum measurement technologies.

PubMed

Ahmadi, Mehdi; Bruschi, David Edward; Sabín, Carlos; Adesso, Gerardo; Fuentes, Ivette

2014-05-22

We present a framework for relativistic quantum metrology that is useful for both Earth-based and space-based technologies. Quantum metrology has been so far successfully applied to design precision instruments such as clocks and sensors which outperform classical devices by exploiting quantum properties. There are advanced plans to implement these and other quantum technologies in space, for instance Space-QUEST and Space Optical Clock projects intend to implement quantum communications and quantum clocks at regimes where relativity starts to kick in. However, typical setups do not take into account the effects of relativity on quantum properties. To include and exploit these effects, we introduce techniques for the application of metrology to quantum field theory. Quantum field theory properly incorporates quantum theory and relativity, in particular, at regimes where space-based experiments take place. This framework allows for high precision estimation of parameters that appear in quantum field theory including proper times and accelerations. Indeed, the techniques can be applied to develop a novel generation of relativistic quantum technologies for gravimeters, clocks and sensors. As an example, we present a high precision device which in principle improves the state-of-the-art in quantum accelerometers by exploiting relativistic effects.

Nurses' knowledge of inhaler technique in the inpatient hospital setting.

PubMed

De Tratto, Katie; Gomez, Christy; Ryan, Catherine J; Bracken, Nina; Steffen, Alana; Corbridge, Susan J

2014-01-01

High rates of inhaler misuse in patients with chronic obstructive pulmonary disease and asthma contribute to hospital readmissions and increased healthcare cost. The purpose of this study was to examine inpatient staff nurses' self-perception of their knowledge of proper inhaler technique compared with demonstrated technique and frequency of providing patients with inhaler technique teaching during hospitalization and at discharge. A prospective, descriptive study. A 495-bed urban academic medical center in the Midwest United States. A convenience sample of 100 nurses working on inpatient medical units. Participants completed a 5-item, 4-point Likert-scale survey evaluating self-perception of inhaler technique knowledge, frequency of providing patient education, and responsibility for providing education. Participants demonstrated inhaler technique to the investigators using both a metered dose inhaler (MDI) and Diskus device inhaler, and performance was measured via a validated checklist. Overall misuse rates were high for both MDI and Diskus devices. There was poor correlation between perceived ability and investigator-measured performance of inhaler technique. Frequency of education during hospitalization and at discharge was related to measured level of performance for the Diskus device but not for the MDI. Nurses are a key component of patient education in the hospital; however, nursing staff lack adequate knowledge of inhaler technique. Identifying gaps in nursing knowledge regarding proper inhaler technique and patient education about proper inhaler technique is important to design interventions that may positively impact patient outcomes. Interventions could include one-on-one education, Web-based education, unit-based education, or hospital-wide competency-based education. All should include return demonstration of appropriate technique.

Instabilities of geared couplings: Theory and practice

NASA Technical Reports Server (NTRS)

Kirk, R. G.; Mondy, R. E.; Murphy, R. C.

1982-01-01

The use of couplings for high speed turbocompressors or pumps is essential to transmit power from the driver. Typical couplings are either of the lubricated gear or dry diaphragm type design. Gear couplings have been the standard design for many years and recent advances in power and speed requirements have pushed the standard design criteria to the limit. Recent test stand and field data on continuous lube gear type couplings have forced a closer examination of design tolerances and concepts to avoid operational instabilities. Two types of mechanical instabilities are reviewed in this paper: (1) entrapped fluid, and (2) gear mesh instability resulting in spacer throw-out onset. Test stand results of these types of instabilities and other directly related problems are presented together with criteria for proper coupling design to avoid these conditions. An additional test case discussed shows the importance of proper material selection and processing and what can happen to an otherwise good design.

Survey Says? A Primer on Web-based Survey Design and Distribution

PubMed Central

Oppenheimer, Adam J.; Pannucci, Christopher J.; Kasten, Steven J.; Haase, Steven C.

2011-01-01

The internet has changed the way in which we gather and interpret information. While books were once the exclusive bearers of data, knowledge is now only a keystroke away. The internet has also facilitated the synthesis of new knowledge. Specifically, it has become a tool through which medical research is conducted. A review of the literature reveals that in the past year, over one-hundred medical publications have been based on web-based survey data alone. Due to emerging internet technologies, web-based surveys can now be launched with little computer knowledge. They may also be self-administered, eliminating personnel requirements. Ultimately, an investigator may build, implement, and analyze survey results with speed and efficiency, obviating the need for mass mailings and data processing. All of these qualities have rendered telephone and mail-based surveys virtually obsolete. Despite these capabilities, web-based survey techniques are not without their limitations, namely recall and response biases. When used properly, however, web-based surveys can greatly simplify the research process. This article discusses the implications of web-based surveys and provides guidelines for their effective design and distribution. PMID:21701347

Analytic methods for design of wave cycles for wave rotor core engines

NASA Technical Reports Server (NTRS)

Resler, Edwin L., Jr.; Mocsari, Jeffrey C.; Nalim, M. R.

1993-01-01

A procedure to design a preliminary wave rotor cycle for any application is presented. To complete a cycle with heat addition there are two separate but related design steps that must be followed. The 'wave' boundary conditions determine the allowable amount of heat added in any case and the ensuing wave pattern requires certain pressure discharge conditions to allow the process to be made cyclic. This procedure, when applied, gives a first estimate of the cycle performance and the necessary information for the next step in the design process, namely the application of a characteristic based or other appropriate detailed one dimensional wave calculation that locates the proper porting around the periphery of the wave rotor. Four examples of the design procedure are given to demonstrate its utility and generality. These examples also illustrate the large gains in performance that could be realized with the use of wave rotor enhanced propulsion cycles.

Multiobjective optimization in structural design with uncertain parameters and stochastic processes

NASA Technical Reports Server (NTRS)

Rao, S. S.

1984-01-01

The application of multiobjective optimization techniques to structural design problems involving uncertain parameters and random processes is studied. The design of a cantilever beam with a tip mass subjected to a stochastic base excitation is considered for illustration. Several of the problem parameters are assumed to be random variables and the structural mass, fatigue damage, and negative of natural frequency of vibration are considered for minimization. The solution of this three-criteria design problem is found by using global criterion, utility function, game theory, goal programming, goal attainment, bounded objective function, and lexicographic methods. It is observed that the game theory approach is superior in finding a better optimum solution, assuming the proper balance of the various objective functions. The procedures used in the present investigation are expected to be useful in the design of general dynamic systems involving uncertain parameters, stochastic process, and multiple objectives.

30 CFR 90.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 90.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

14 CFR 27.733 - Tires.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Tires. 27.733 Section 27.733 Aeronautics... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction Landing Gear § 27.733 Tires. (a) Each landing gear wheel must have a tire— (1) That is a proper fit on the rim of the wheel; and (2) Of the proper...

Causes of Indoor Air Quality Problems in Schools: Summary of Scientific Research. Revised Edition.

ERIC Educational Resources Information Center

Bayer, Charlene W.; Crow, Sidney A.; Fischer, John

Understanding the primary causes of indoor air quality (IAQ) problems and how controllable factors--proper heating, ventilation and air-conditioning (HVAC) system design, allocation of adequate outdoor air, proper filtration, effective humidity control, and routine maintenance--can avert problems may help all building owners, operators, and…

Construction Trade Course. Bilingual Vocational Instructional Materials.

ERIC Educational Resources Information Center

Lopez-Cox, Guadalupe

This building trades course, one of a series of bilingual English-Spanish vocational education courses, is designed to introduce the basic skills that a student must know in the construction field. It is geared to teach the student basic manipulative skills, safety judgments, proper work habits, desirable attitudes, and proper behavior for initial…

Fabrication of Three-dimensional Paper-based Microfluidic Devices for Immunoassays.

PubMed

Fernandes, Syrena C; Wilson, Daniel J; Mace, Charles R

2017-03-09

Paper wicks fluids autonomously due to capillary action. By patterning paper with hydrophobic barriers, the transport of fluids can be controlled and directed within a layer of paper. Moreover, stacking multiple layers of patterned paper creates sophisticated three-dimensional microfluidic networks that can support the development of analytical and bioanalytical assays. Paper-based microfluidic devices are inexpensive, portable, easy to use, and require no external equipment to operate. As a result, they hold great promise as a platform for point-of-care diagnostics. In order to properly evaluate the utility and analytical performance of paper-based devices, suitable methods must be developed to ensure their manufacture is reproducible and at a scale that is appropriate for laboratory settings. In this manuscript, a method to fabricate a general device architecture that can be used for paper-based immunoassays is described. We use a form of additive manufacturing (multi-layer lamination) to prepare devices that comprise multiple layers of patterned paper and patterned adhesive. In addition to demonstrating the proper use of these three-dimensional paper-based microfluidic devices with an immunoassay for human chorionic gonadotropin (hCG), errors in the manufacturing process that may result in device failures are discussed. We expect this approach to manufacturing paper-based devices will find broad utility in the development of analytical applications designed specifically for limited-resource settings.

Telemedicine for Developing Countries. A Survey and Some Design Issues.

PubMed

Combi, Carlo; Pozzani, Gabriele; Pozzi, Giuseppe

2016-11-02

Developing countries need telemedicine applications that help in many situations, when physicians are a small number with respect to the population, when specialized physicians are not available, when patients and physicians in rural villages need assistance in the delivery of health care. Moreover, the requirements of telemedicine applications for developing countries are somewhat more demanding than for developed countries. Indeed, further social, organizational, and technical aspects need to be considered for successful telemedicine applications in developing countries. We consider all the major projects in telemedicine, devoted to developing countries, as described by the proper scientific literature. On the basis of such literature, we want to define a specific taxonomy that allows a proper classification and a fast overview of telemedicine projects in developing countries. Moreover, by considering both the literature and some recent direct experiences, we want to complete such overview by discussing some design issues to be taken into consideration when developing telemedicine software systems. We considered and reviewed the major conferences and journals in depth, and looked for reports on the telemedicine projects. We provide the reader with a survey of the main projects and systems, from which we derived a taxonomy of features of telemedicine systems for developing countries. We also propose and discuss some classification criteria for design issues, based on the lessons learned in this research area. We highlight some challenges and recommendations to be considered when designing a telemedicine system for developing countries.

Proper name retrieval in temporal lobe epilepsy: naming of famous faces and landmarks.

PubMed

Benke, Thomas; Kuen, Eva; Schwarz, Michael; Walser, Gerald

2013-05-01

The objective of this study was to further explore proper name (PN) retrieval and conceptual knowledge in patients with left and right temporal lobe epilepsy (69 patients with LTLE and 62 patients with RTLE) using a refined assessment procedure. Based on the performance of a large group of age- and education-matched normals, a new test of famous faces and famous landmarks was designed. Recognition, naming, and semantic knowledge were assessed consecutively, allowing for a better characterization of deficient levels in the naming system. Impairment in PN retrieval was common in the cohort with TLE. Furthermore, side of seizure onset impaired stages of name retrieval differently: LTLE impaired the lexico-phonological processing, whereas RTLE mainly impaired the perceptual-semantic stage of object recognition. In addition to deficient PN retrieval, patients with TLE had reduced conceptual knowledge regarding famous persons and landmarks. Copyright © 2013 Elsevier Inc. All rights reserved.

A beacon interval shifting scheme for interference mitigation in body area networks.

PubMed

Kim, Seungku; Kim, Seokhwan; Kim, Jin-Woo; Eom, Doo-Seop

2012-01-01

This paper investigates the issue of interference avoidance in body area networks (BANs). IEEE 802.15 Task Group 6 presented several schemes to reduce such interference, but these schemes are still not proper solutions for BANs. We present a novel distributed TDMA-based beacon interval shifting scheme that reduces interference in the BANs. A design goal of the scheme is to avoid the wakeup period of each BAN coinciding with other networks by employing carrier sensing before a beacon transmission. We analyze the beacon interval shifting scheme and investigate the proper back-off length when the channel is busy. We compare the performance of the proposed scheme with the schemes presented in IEEE 802.15 Task Group 6 using an OMNeT++ simulation. The simulation results show that the proposed scheme has a lower packet loss, energy consumption, and delivery-latency than the schemes of IEEE 802.15 Task Group 6.

A Beacon Interval Shifting Scheme for Interference Mitigation in Body Area Networks

PubMed Central

Kim, Seungku; Kim, Seokhwan; Kim, Jin-Woo; Eom, Doo-Seop

2012-01-01

This paper investigates the issue of interference avoidance in body area networks (BANs). IEEE 802.15 Task Group 6 presented several schemes to reduce such interference, but these schemes are still not proper solutions for BANs. We present a novel distributed TDMA-based beacon interval shifting scheme that reduces interference in the BANs. A design goal of the scheme is to avoid the wakeup period of each BAN coinciding with other networks by employing carrier sensing before a beacon transmission. We analyze the beacon interval shifting scheme and investigate the proper back-off length when the channel is busy. We compare the performance of the proposed scheme with the schemes presented in IEEE 802.15 Task Group 6 using an OMNeT++ simulation. The simulation results show that the proposed scheme has a lower packet loss, energy consumption, and delivery-latency than the schemes of IEEE 802.15 Task Group 6. PMID:23112639

Texas flexible pavements overlays : review and analysis of existing databases.

DOT National Transportation Integrated Search

2011-12-01

Proper calibration of pavement design and rehabilitation performance models to : conditions in Texas is essential for cost-effective flexible pavement design. The degree of : excellence with which TxDOTs pavement design models is calibrated will d...

Constitutional Reform for Conflict Management

DTIC Science & Technology

2014-04-01

conflict. Empirical studies reveal that both accommodative and integrative constitutional design can produce political stability , if properly...reform, and the ability of various constitutional designs to promote democracy and political stability .

ASCAN WATER SURVIVAL SCHOOL TRAINING VIEW

NASA Image and Video Library

2013-03-05

S78-33689 (1978) ASCAN WATER SURVIVAL SCHOOL TRAINING VIEW 1978. Several new astronaut trainees are seen prior to a training exercise at the water survival school in Florida attended by 16 of the candidates. From far left to right are Shannon W. Lucid, Steven A. Hawley, Jeffrey A. Hoffman, Ronald E. McNair and Rhea Seddon. The overall program, held at Homestead Air Force Base, was designed to prepare the trainees for proper measures to take in the event of ejection from an aircraft over water. NASA Photograph.

Broadening the Cloaking Bandwidth with Non-Foster Metasurfaces

NASA Astrophysics Data System (ADS)

Chen, Pai-Yen; Argyropoulos, Christos; Alù, Andrea

2013-12-01

We introduce the concept and practical design of broadband, ultrathin cloaks based on non-Foster, negatively capacitive metasurfaces. By using properly tailored, active frequency-selective screens conformal to an object, within the realm of a practical realization, we show that it is possible to drastically reduce the scattering over a wide frequency range in the microwave regime, orders of magnitude broader than any available passive cloaking technology. The proposed active cloak may impact not only invisibility and camouflaging, but also practical antenna and sensing applications.

Analytical display design for flight tasks conducted under instrument meteorological conditions. [human factors engineering of pilot performance for display device design in instrument landing systems

NASA Technical Reports Server (NTRS)

Hess, R. A.

1976-01-01

Paramount to proper utilization of electronic displays is a method for determining pilot-centered display requirements. Display design should be viewed fundamentally as a guidance and control problem which has interactions with the designer's knowledge of human psychomotor activity. From this standpoint, reliable analytical models of human pilots as information processors and controllers can provide valuable insight into the display design process. A relatively straightforward, nearly algorithmic procedure for deriving model-based, pilot-centered display requirements was developed and is presented. The optimal or control theoretic pilot model serves as the backbone of the design methodology, which is specifically directed toward the synthesis of head-down, electronic, cockpit display formats. Some novel applications of the optimal pilot model are discussed. An analytical design example is offered which defines a format for the electronic display to be used in a UH-1H helicopter in a landing approach task involving longitudinal and lateral degrees of freedom.

Design and Analysis of Tooth Impact Test Rig for Spur Gear

NASA Astrophysics Data System (ADS)

Ghazali, Wafiuddin Bin Md; Aziz, Ismail Ali Bin Abdul; Daing Idris, Daing Mohamad Nafiz Bin; Ismail, Nurazima Binti; Sofian, Azizul Helmi Bin

2016-02-01

This paper is about the design and analysis of a prototype of tooth impact test rig for spur gear. The test rig was fabricated and analysis was conducted to study its’ limitation and capabilities. The design of the rig is analysed to ensure that there will be no problem occurring during the test and reliable data can be obtained. From the result of the analysis, the maximum amount of load that can be applied, the factor of safety of the machine, the stresses on the test rig parts were determined. This is important in the design consideration of the test rig. The materials used for the fabrication of the test rig were also discussed and analysed. MSC Nastran Patran software was used to analyse the model, which was designed by using SolidWorks 2014 software. Based from the results, there were limitations found from the initial design and the test rig design needs to be improved in order for the test rig to operate properly.

Optical Telescope System-Level Design Considerations for a Space-Based Gravitational Wave Mission

NASA Technical Reports Server (NTRS)

Livas, Jeffrey C.; Sankar, Shannon R.

2016-01-01

The study of the Universe through gravitational waves will yield a revolutionary new perspective on the Universe, which has been intensely studied using electromagnetic signals in many wavelength bands. A space-based gravitational wave observatory will enable access to a rich array of astrophysical sources in the measurement band from 0.1 to 100 mHz, and nicely complement observations from ground-based detectors as well as pulsar timing arrays by sampling a different range of compact object masses and astrophysical processes. The observatory measures gravitational radiation by precisely monitoring the tiny change in the proper distance between pairs of freely falling proof masses. These masses are separated by millions of kilometers and, using a laser heterodyne interferometric technique, the change in their proper separation is detected to approx. 10 pm over timescales of 1000 seconds, a fractional precision of better than one part in 10(exp 19). Optical telescopes are essential for the implementation of this precision displacement measurement. In this paper we describe some of the key system level design considerations for the telescope subsystem in a mission context. The reference mission for this purpose is taken to be the enhanced Laser Interferometry Space Antenna mission (eLISA), a strong candidate for the European Space Agency's Cosmic Visions L3 launch opportunity in 2034. We will review the flow-down of observatory level requirements to the telescope subsystem, particularly pertaining to the effects of telescope dimensional stability and scattered light suppression, two performance specifications which are somewhat different from the usual requirements for an image forming telescope.

Transonic Flutter Suppression Control Law Design, Analysis and Wind-Tunnel Results

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek

1999-01-01

The benchmark active controls technology and wind tunnel test program at NASA Langley Research Center was started with the objective to investigate the nonlinear, unsteady aerodynamics and active flutter suppression of wings in transonic flow. The paper will present the flutter suppression control law design process, numerical nonlinear simulation and wind tunnel test results for the NACA 0012 benchmark active control wing model. The flutter suppression control law design processes using classical, and minimax techniques are described. A unified general formulation and solution for the minimax approach, based on the steady state differential game theory is presented. Design considerations for improving the control law robustness and digital implementation are outlined. It was shown that simple control laws when properly designed based on physical principles, can suppress flutter with limited control power even in the presence of transonic shocks and flow separation. In wind tunnel tests in air and heavy gas medium, the closed-loop flutter dynamic pressure was increased to the tunnel upper limit of 200 psf. The control law robustness and performance predictions were verified in highly nonlinear flow conditions, gain and phase perturbations, and spoiler deployment. A non-design plunge instability condition was also successfully suppressed.

The Design of Finite State Machine for Asynchronous Replication Protocol

NASA Astrophysics Data System (ADS)

Wang, Yanlong; Li, Zhanhuai; Lin, Wei; Hei, Minglei; Hao, Jianhua

Data replication is a key way to design a disaster tolerance system and to achieve reliability and availability. It is difficult for a replication protocol to deal with the diverse and complex environment. This means that data is less well replicated than it ought to be. To reduce data loss and to optimize replication protocols, we (1) present a finite state machine, (2) run it to manage an asynchronous replication protocol and (3) report a simple evaluation of the asynchronous replication protocol based on our state machine. It's proved that our state machine is applicable to guarantee the asynchronous replication protocol running in the proper state to the largest extent in the event of various possible events. It also can helpful to build up replication-based disaster tolerance systems to ensure the business continuity.

A general model-based design of experiments approach to achieve practical identifiability of pharmacokinetic and pharmacodynamic models.

PubMed

Galvanin, Federico; Ballan, Carlo C; Barolo, Massimiliano; Bezzo, Fabrizio

2013-08-01

The use of pharmacokinetic (PK) and pharmacodynamic (PD) models is a common and widespread practice in the preliminary stages of drug development. However, PK-PD models may be affected by structural identifiability issues intrinsically related to their mathematical formulation. A preliminary structural identifiability analysis is usually carried out to check if the set of model parameters can be uniquely determined from experimental observations under the ideal assumptions of noise-free data and no model uncertainty. However, even for structurally identifiable models, real-life experimental conditions and model uncertainty may strongly affect the practical possibility to estimate the model parameters in a statistically sound way. A systematic procedure coupling the numerical assessment of structural identifiability with advanced model-based design of experiments formulations is presented in this paper. The objective is to propose a general approach to design experiments in an optimal way, detecting a proper set of experimental settings that ensure the practical identifiability of PK-PD models. Two simulated case studies based on in vitro bacterial growth and killing models are presented to demonstrate the applicability and generality of the methodology to tackle model identifiability issues effectively, through the design of feasible and highly informative experiments.

The Mine Locomotive Wireless Network Strategy Based on Successive Interference Cancellation

PubMed Central

Wu, Liaoyuan; Han, Jianghong; Wei, Xing; Shi, Lei; Ding, Xu

2015-01-01

We consider a wireless network strategy based on successive interference cancellation (SIC) for mine locomotives. We firstly build the original mathematical model for the strategy which is a non-convex model. Then, we examine this model intensively, and figure out that there are certain regulations embedded in it. Based on these findings, we are able to reformulate the model into a new form and design a simple algorithm which can assign each locomotive with a proper transmitting scheme during the whole schedule procedure. Simulation results show that the outcomes obtained through this algorithm are improved by around 50% compared with those that do not apply the SIC technique. PMID:26569240

Integration of PGD-virtual charts into an engineering design process

NASA Astrophysics Data System (ADS)

Courard, Amaury; Néron, David; Ladevèze, Pierre; Ballere, Ludovic

2016-04-01

This article deals with the efficient construction of approximations of fields and quantities of interest used in geometric optimisation of complex shapes that can be encountered in engineering structures. The strategy, which is developed herein, is based on the construction of virtual charts that allow, once computed offline, to optimise the structure for a negligible online CPU cost. These virtual charts can be used as a powerful numerical decision support tool during the design of industrial structures. They are built using the proper generalized decomposition (PGD) that offers a very convenient framework to solve parametrised problems. In this paper, particular attention has been paid to the integration of the procedure into a genuine engineering design process. In particular, a dedicated methodology is proposed to interface the PGD approach with commercial software.

Pressure investigation of NASA leading edge vortex flaps on a 60 deg Delta wing

NASA Technical Reports Server (NTRS)

Marchman, J. F., III; Donatelli, D. A.; Terry, J. E.

1983-01-01

Pressure distributions on a 60 deg Delta Wing with NASA designed leading edge vortex flaps (LEVF) were found in order to provide more pressure data for LEVF and to help verify NASA computer codes used in designing these flaps. These flaps were intended to be optimized designs based on these computer codes. However, the pressure distributions show that the flaps wre not optimum for the size and deflection specified. A second drag-producing vortex forming over the wing indicated that the flap was too large for the specified deflection. Also, it became apparent that flap thickness has a possible effect on the reattachment location of the vortex. Research is continuing to determine proper flap size and deflection relationships that provide well-behaved flowfields and acceptable hinge-moment characteristics.

IGDS/TRAP Interface Program (ITIP). Software User Manual (SUM). [network flow diagrams for coal gasification studies

NASA Technical Reports Server (NTRS)

Jefferys, S.; Johnson, W.; Lewis, R.; Rich, R.

1981-01-01

This specification establishes the requirements, concepts, and preliminary design for a set of software known as the IGDS/TRAP Interface Program (ITIP). This software provides the capability to develop at an Interactive Graphics Design System (IGDS) design station process flow diagrams for use by the NASA Coal Gasification Task Team. In addition, ITIP will use the Data Management and Retrieval System (DMRS) to maintain a data base from which a properly formatted input file to the Time-Line and Resources Analysis Program (TRAP) can be extracted. This set of software will reside on the PDP-11/70 and will become the primary interface between the Coal Gasification Task Team and IGDS, DMRS, and TRAP. The user manual for the computer program is presented.

Air transportation in the California Corridor of 2010

NASA Technical Reports Server (NTRS)

Cameron, M.; Mahaffy, K.; Yanagi, G.; Lechmanski, L.; Riddle, T.; Howard, K.; Chan, C.; Gorman, M.; Bauer, B.

1989-01-01

The topic of the 1988-1989 NASA/USRA Advanced Design Project at California Polytechnic State University, San Luis Obispo, was the development of an air transportation system to meet the needs of the California Corridor for the year 2010. As aircraft design is taught by two instructors having different philosophies about the teaching process, the two classes took different approaches to address the problem. The first part of this summary (California Air Transit System) represents the work done by the students of Professor A. E. Andreoli, who followed a systems approach, emphasizing the determination of the proper mission. The second part of the summary (Four Aircraft to Service the California Corridor) contains the four aircraft designed by Dr. D. R. Sandlin's class based on specifications determined from work done in previous years.

The use of modern measurement techniques for designing pro ecological constructions

NASA Astrophysics Data System (ADS)

Wieczorowski, Michał; Gapiński, Bartosz; Szymański, Maciej; Rękas, Artur

2017-10-01

In the paper some possibilities of application modern length and angle metrology techniques to design constructions that support ecology were presented. The paper is based on a project where a lighter bus and train car seat was developed. Different options were presented including static and dynamic photogrammetry, computed tomography and thermography. Research related with dynamic behaviour of designed structures gave input to determine deformation of a seat and passengers sitting on it during communication accidents. Works connected to strength of construction elements made it possible to optimize its dimensions maintaining proper durability. Metrological actions taken in relation to production machines and equipment enabled to better recognize phenomena that take place during manufacturing process and to correct its parameters, what in turns also contributed to slim down the construction.

Design of optimal and ideal 2-D concentrators with the collector immersed in a dielectric tube

NASA Astrophysics Data System (ADS)

Minano, J. C.; Ruiz, J. M.; Luque, A.

1983-12-01

A method is presented for designing ideal and optimal 2-D concentrators when the collector is placed inside a dielectric tube, for the particular case of a bifacial solar collector. The prototype 2-D (cylindrical geometry) concentrator is the compound parabolic concentrator or CPC, and from the beginning of development, it was found by Winston (1978) that filling up the concentrator with a transparent dielectric medium results in a big improvement of the optical properties. The method reported here is based on the extreme ray principle of design and avoids the use of differential equations by means of a proper appliction of Fermat's principle. One advantage of these concentrators is that they allow the size to be small compared with classical CPCs.

RNA imaging: tracking in real-time RNA transport in neurons using molecular beacons and confocal microscopy.

PubMed

Zepeda, Angélica; Arias, Clorinda; Flores-Jasso, Fabian; Vaca, Luis

2013-01-01

RNAs are present within eukaryotic cells and are involved in several biological processes. RNA transport within cell compartments is important for proper cell function. To understand in depth the cellular processes in which RNA is involved requires a method that reveals RNA localization in real time in a sub-cellular context in living cells. In this protocol we describe a method for imaging RNA in living cells and in particular in neuronal cultures based on cell microinjection of molecular beacons in conjunction with confocal microscopy. This methodology overcomes some of the main obstacles for imaging RNA in live cells since microinjection allows the delivery of the probe to a desired cellular compartment and MBs bind with high specificity to its target RNA without inhibiting its function. The proper design of the MBs is essential to obtain RNA-MB association at the temperature of the cell cytosol. MBs design with other purposes in mind (such as PCR experiments) have a design that facilitates association to its target at high temperatures, rendering them unsuitable for live cell imaging. Using the methodology described in this chapter allows the study of RNA transport to different regions of neurons and may be combined with the tagging of proteins of interest to measure co-transport of the protein and the RNA to different cellular regions. Copyright © 2013 Elsevier Inc. All rights reserved.

SOI N-Channel Field Effect Transistors, CHT-NMOS80, for Extreme Temperatures

NASA Technical Reports Server (NTRS)

Patterson, Richard L.; Hammoud, Almad

2009-01-01

Extreme temperatures, both hot and cold, are anticipated in many of NASA space exploration missions as well as in terrestrial applications. One can seldom find electronics that are capable of operation under both regimes. Even for operation under one (hot or cold) temperature extreme, some thermal controls need to be introduced to provide appropriate ambient temperatures so that spacecraft on-board or field on-site electronic systems work properly. The inclusion of these controls, which comprise of heating elements and radiators along with their associated structures, adds to the complexity in the design of the system, increases cost and weight, and affects overall reliability. Thus, it would be highly desirable and very beneficial to eliminate these thermal measures in order to simplify system's design, improve efficiency, reduce development and launch costs, and improve reliability. These requirements can only be met through the development of electronic parts that are designed for proper and efficient operation under extreme temperature conditions. Silicon-on-insulator (SOI) based devices are finding more use in harsh environments due to the benefits that their inherent design offers in terms of reduced leakage currents, less power consumption, faster switching speeds, good radiation tolerance, and extreme temperature operability. Little is known, however, about their performance at cryogenic temperatures and under wide thermal swings. The objective of this work was to evaluate the performance of a new commercial-off-the-shelf (COTS) SOI parts over an extended temperature range and to determine the effects of thermal cycling on their performance. The results will establish a baseline on the suitability of such devices for use in space exploration missions under extreme temperatures, and will aid mission planners and circuit designers in the proper selection of electronic parts and circuits. The electronic part investigated in this work comprised of a CHT-NMOS80 high temperature N-channel MOSFET (metal-oxide semiconductor field-effect transistor) device that was manufactured by CISSOID. This high voltage, medium-power transistor is fabricated using SOI processes and is designed for extreme wide temperature applications such as geothermal well logging, aerospace and avionics, and automotive industry. It has a high DC current capability and is specified for operation in the temperature range of -55 C to +225 C

A new design methodology of obtaining wide band high gain broadband parametric source for infrared wavelength applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maji, Partha Sona; Roy Chaudhuri, Partha

In this article, we have presented a new design methodology of obtaining wide band parametric sources based on highly nonlinear chalcogenide material of As{sub 2}S{sub 3}. The dispersion profile of the photonic crystal fiber (PCF) has been engineered wisely by reducing the diameter of the second air-hole ring to have a favorable higher order dispersion parameter. The parametric gain dependence upon fiber length, pump power, and different pumping wavelengths has been investigated in detail. Based upon the nonlinear four wave mixing phenomenon, we are able to achieve a wideband parametric amplifier with peak gain of 29 dB with FWHM of ≈2000 nmmore » around the IR wavelength by proper tailoring of the dispersion profile of the PCF with a continuous wave Erbium (Er{sup 3+})-doped ZBLAN fiber laser emitting at 2.8 μm as the pump source with an average power of 5 W. The new design methodology will unleash a new dimension to the chalcogenide material based investigation for wavelength translation around IR wavelength band.« less

Diffusion-Based Design of Multi-Layered Ophthalmic Lenses for Controlled Drug Release

PubMed Central

Pimenta, Andreia F. R.; Serro, Ana Paula; Paradiso, Patrizia; Saramago, Benilde

2016-01-01

The study of ocular drug delivery systems has been one of the most covered topics in drug delivery research. One potential drug carrier solution is the use of materials that are already commercially available in ophthalmic lenses for the correction of refractive errors. In this study, we present a diffusion-based mathematical model in which the parameters can be adjusted based on experimental results obtained under controlled conditions. The model allows for the design of multi-layered therapeutic ophthalmic lenses for controlled drug delivery. We show that the proper combination of materials with adequate drug diffusion coefficients, thicknesses and interfacial transport characteristics allows for the control of the delivery of drugs from multi-layered ophthalmic lenses, such that drug bursts can be minimized, and the release time can be maximized. As far as we know, this combination of a mathematical modelling approach with experimental validation of non-constant activity source lamellar structures, made of layers of different materials, accounting for the interface resistance to the drug diffusion, is a novel approach to the design of drug loaded multi-layered contact lenses. PMID:27936138

Fuzzy logic-based flight control system design

NASA Astrophysics Data System (ADS)

Nho, Kyungmoon

The application of fuzzy logic to aircraft motion control is studied in this dissertation. The self-tuning fuzzy techniques are developed by changing input scaling factors to obtain a robust fuzzy controller over a wide range of operating conditions and nonlinearities for a nonlinear aircraft model. It is demonstrated that the properly adjusted input scaling factors can meet the required performance and robustness in a fuzzy controller. For a simple demonstration of the easy design and control capability of a fuzzy controller, a proportional-derivative (PD) fuzzy control system is compared to the conventional controller for a simple dynamical system. This thesis also describes the design principles and stability analysis of fuzzy control systems by considering the key features of a fuzzy control system including the fuzzification, rule-base and defuzzification. The wing-rock motion of slender delta wings, a linear aircraft model and the six degree of freedom nonlinear aircraft dynamics are considered to illustrate several self-tuning methods employing change in input scaling factors. Finally, this dissertation is concluded with numerical simulation of glide-slope capture in windshear demonstrating the robustness of the fuzzy logic based flight control system.

Mass reduction patterning of silicon-on-oxide-based micromirrors

NASA Astrophysics Data System (ADS)

Hall, Harris J.; Green, Andrew; Dooley, Sarah; Schmidt, Jason D.; Starman, LaVern A.; Langley, Derrick; Coutu, Ronald A.

2016-10-01

It has long been recognized in the design of micromirror-based optical systems that balancing static flatness of the mirror surface through structural design with the system's mechanical dynamic response is challenging. Although a variety of mass reduction approaches have been presented in the literature to address this performance trade, there has been little quantifiable comparison reported. In this work, different mass reduction approaches, some unique to the work, are quantifiably compared with solid plate thinning in both curvature and mass using commercial finite element simulation of a specific square silicon-on-insulator-based micromirror geometry. Other important considerations for micromirror surfaces, including surface profile and smoothness, are also discussed. Fabrication of one of these geometries, a two-dimensional tessellated square pattern, was performed in the presence of a 400-μm-tall central post structure using a simple single mask process. Limited experimental curvature measurements of fabricated samples are shown to correspond well with properly characterized simulation results and indicate ˜67% improvement in radius of curvature in comparison to a solid plate design of equivalent mass.

An Overview on Wireless Sensor Networks Technology and Evolution

PubMed Central

Buratti, Chiara; Conti, Andrea; Dardari, Davide; Verdone, Roberto

2009-01-01

Wireless sensor networks (WSNs) enable new applications and require non-conventional paradigms for protocol design due to several constraints. Owing to the requirement for low device complexity together with low energy consumption (i.e., long network lifetime), a proper balance between communication and signal/data processing capabilities must be found. This motivates a huge effort in research activities, standardization process, and industrial investments on this field since the last decade. This survey paper aims at reporting an overview of WSNs technologies, main applications and standards, features in WSNs design, and evolutions. In particular, some peculiar applications, such as those based on environmental monitoring, are discussed and design strategies highlighted; a case study based on a real implementation is also reported. Trends and possible evolutions are traced. Emphasis is given to the IEEE 802.15.4 technology, which enables many applications of WSNs. Some example of performance characteristics of 802.15.4-based networks are shown and discussed as a function of the size of the WSN and the data type to be exchanged among nodes. PMID:22423202

The Essentials of Proper Wine Service.

ERIC Educational Resources Information Center

Manago, Gary H.

This instructional unit was designed to assist the food services instructor and/or the restaurant manager in training students and/or staff in the proper procedure for serving wines to guests. The lesson plans included in this unit focus on: (1) the different types of wine glasses and their uses; (2) the parts of a wine glass; (3) the proper…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fazalare, R.W.; Hayes, S.J.

One decision hydro project designers and developers make when building a new facility is what method to use to embed the turbine spiral case in the powerhouse concrete. The type of technique chosen often is based on the long-standing practice or individual preference of the plant owner. However, according to a recent industry survey, any method can be used successfully if proper design and installation procedures are followed. Although pressurized embedment has been the prominent method in the past, especially in the US, the bare deflated casing method is gaining popularity throughout the world because it can reduce cost andmore » construction time. This method has been the primary technique used with apparent success in Japan and Scandinavia.« less

In use performance of catalytic converters on properly maintained high mileage vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabourin, M.A.; Larson, R.E.; Donahue, K.S.

1986-01-01

A test program to evaluate the performance of catalytic converters from fifty-six 1981 and 1982 model year high mileage properly maintained in-use vehicles (from 21 engine families) was performed by the Certification Division of the Office of Mobile Sources (EPA). The program is called the Catalyst Change Program. All program vehicles were screened for proper maintenance and for mileages that ranged from 35,000 to 60,000 miles. Among vehicles belonging to 21 high sales volume and high technology engine and emission control system designs tested, poor catalyst performance was determined to be a significant contributor to emissions failure of properly-maintained vehiclesmore » at or near their warranted useful life mileage.« less

Assessment of SOI Devices and Circuits at Extreme Temperatures

NASA Technical Reports Server (NTRS)

Elbuluk, Malik; Hammoud, Ahmad; Patterson, Richard L.

2007-01-01

Electronics designed for use in future NASA space exploration missions are expected to encounter extreme temperatures and wide thermal swings. Such missions include planetary surface exploration, bases, rovers, landers, orbiters, and satellites. Electronics designed for such applications must, therefore, be able to withstand exposure to extreme temperatures and to perform properly for the duration of mission. The Low Temperature Electronics Program at the NASA Glenn Research Center focuses on research and development of electrical devices, circuits, and systems suitable for applications in deep space exploration missions and aerospace environment. Silicon-On-Insulator (SOI) technology has been under active consideration in the electronics industry for many years due to the advantages that it can provide in integrated circuit (IC) chips and computer processors. Faster switching, less power, radiationtolerance, reduced leakage, and high temp-erature capability are some of the benefits that are offered by using SOI-based devices. A few SOI circuits are available commercially. However, there is a noticeable interest in SOI technology for different applications. Very little data, however, exist on the performance of such circuits under cryogenic temperatures. In this work, the performance of SOI integrated circuits, evaluated under low temperature and thermal cycling, are reported. In particular, three examples of SOI circuits that have been tested for operation at low at temperatures are given. These circuits are SOI operational amplifiers, timers and power MOSFET drivers. The investigations were carried out to establish a baseline on the functionality and to determine suitability of these circuits for use in space exploration missions at cryogenic temperatures. The findings are useful to mission planners and circuit designers so that proper selection of electronic parts can be made, and risk assessment can be established for such circuits for use in space missions.

Verification of Emergent Behaviors in Swarm-based Systems

NASA Technical Reports Server (NTRS)

Rouff, Christopher; Vanderbilt, Amy; Hinchey, Mike; Truszkowski, Walt; Rash, James

2004-01-01

The emergent properties of swarms make swarm-based missions powerful, but at the same time more difficult to design and to assure that the proper behaviors will emerge. We are currently investigating formal methods and techniques for verification and validation of swarm-based missions. The Autonomous Nano-Technology Swarm (ANTS) mission is being used as an example and case study for swarm-based missions to experiment and test current formal methods with intelligent swarms. Using the ANTS mission, we have evaluated multiple formal methods to determine their effectiveness in modeling and assuring swarm behavior. This paper introduces how intelligent swarm technology is being proposed for NASA missions, and gives the results of a comparison of several formal methods and approaches for specifying intelligent swarm-based systems and their effectiveness for predicting emergent behavior.

Prediction-based association control scheme in dense femtocell networks.

PubMed

Sung, Nak Woon; Pham, Ngoc-Thai; Huynh, Thong; Hwang, Won-Joo; You, Ilsun; Choo, Kim-Kwang Raymond

2017-01-01

The deployment of large number of femtocell base stations allows us to extend the coverage and efficiently utilize resources in a low cost manner. However, the small cell size of femtocell networks can result in frequent handovers to the mobile user, and consequently throughput degradation. Thus, in this paper, we propose predictive association control schemes to improve the system's effective throughput. Our design focuses on reducing handover frequency without impacting on throughput. The proposed schemes determine handover decisions that contribute most to the network throughput and are proper for distributed implementations. The simulation results show significant gains compared with existing methods in terms of handover frequency and network throughput perspective.

Empirical Requirements Analysis for Mars Surface Operations Using the Flashline Mars Arctic Research Station

NASA Technical Reports Server (NTRS)

Clancey, William J.; Lee, Pascal; Sierhuis, Maarten; Norvig, Peter (Technical Monitor)

2001-01-01

Living and working on Mars will require model-based computer systems for maintaining and controlling complex life support, communication, transportation, and power systems. This technology must work properly on the first three-year mission, augmenting human autonomy, without adding-yet more complexity to be diagnosed and repaired. One design method is to work with scientists in analog (mars-like) setting to understand how they prefer to work, what constrains will be imposed by the Mars environment, and how to ameliorate difficulties. We describe how we are using empirical requirements analysis to prototype model-based tools at a research station in the High Canadian Arctic.

An Informatics Based Approach to Reduce the Grain Size of Cast Hadfield Steel

NASA Astrophysics Data System (ADS)

Dey, Swati; Pathak, Shankha; Sheoran, Sumit; Kela, Damodar H.; Datta, Shubhabrata

2016-04-01

Materials Informatics concept using computational intelligence based approaches are employed to bring out the significant alloying additions to achieve grain refinement in cast Hadfield steel. Castings of Hadfield steels used for railway crossings, requires fine grained austenitic structure. Maintaining proper grain size of this component is very crucial in order to achieve the desired properties and service life. This work studies the important variables affecting the grain size of such steels which includes the compositional and processing variables. The computational findings and prior knowledge is used to design the alloy, which is subjected to a few trials to validate the findings.

Tracking control of a closed-chain five-bar robot with two degrees of freedom by integration of an approximation-based approach and mechanical design.

PubMed

Cheng, Long; Hou, Zeng-Guang; Tan, Min; Zhang, W J

2012-10-01

The trajectory tracking problem of a closed-chain five-bar robot is studied in this paper. Based on an error transformation function and the backstepping technique, an approximation-based tracking algorithm is proposed, which can guarantee the control performance of the robotic system in both the stable and transient phases. In particular, the overshoot, settling time, and final tracking error of the robotic system can be all adjusted by properly setting the parameters in the error transformation function. The radial basis function neural network (RBFNN) is used to compensate the complicated nonlinear terms in the closed-loop dynamics of the robotic system. The approximation error of the RBFNN is only required to be bounded, which simplifies the initial "trail-and-error" configuration of the neural network. Illustrative examples are given to verify the theoretical analysis and illustrate the effectiveness of the proposed algorithm. Finally, it is also shown that the proposed approximation-based controller can be simplified by a smart mechanical design of the closed-chain robot, which demonstrates the promise of the integrated design and control philosophy.

Scaled centrifugal compressor, collector and running gear program

NASA Technical Reports Server (NTRS)

Kenehan, J. G.

1983-01-01

The Scaled Centrifugal Compressor, Collector and Running gear Program was conducted in support of an overall NASA strategy to improve small-compressor performance, durability, and reliability while reducing initial and life-cycle costs. Accordingly, Garrett designed and provided a test rig, gearbox coupling, and facility collector for a new NASA facility, and provided a scaled model of an existing, high-performance impeller for evaluation scaling effects on aerodynamic performance and for obtaining other performance data. Test-rig shafting was designed to operate smoothly throughout a speed range up to 60,000 rpm. Pressurized components were designed to operate at pressures up to 300 psia and at temperatures to 1000 F. Nonrotating components were designed to provide a margin-of-safety of 0.05 or greater; rotating components, for a margin-of-safety based on allowable yield and ultimate strengths. Design activities were supported by complete design analysis, and the finished hardware was subjected to check-runs to confirm proper operation. The test rig will support a wide range of compressor tests and evaluations.

Design of an MR image processing module on an FPGA chip

NASA Astrophysics Data System (ADS)

Li, Limin; Wyrwicz, Alice M.

2015-06-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128 × 128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments.

Design optimization of piezoresistive cantilevers for force sensing in air and water

PubMed Central

Doll, Joseph C.; Park, Sung-Jin; Pruitt, Beth L.

2009-01-01

Piezoresistive cantilevers fabricated from doped silicon or metal films are commonly used for force, topography, and chemical sensing at the micro- and macroscales. Proper design is required to optimize the achievable resolution by maximizing sensitivity while simultaneously minimizing the integrated noise over the bandwidth of interest. Existing analytical design methods are insufficient for modeling complex dopant profiles, design constraints, and nonlinear phenomena such as damping in fluid. Here we present an optimization method based on an analytical piezoresistive cantilever model. We use an existing iterative optimizer to minimimize a performance goal, such as minimum detectable force. The design tool is available as open source software. Optimal cantilever design and performance are found to strongly depend on the measurement bandwidth and the constraints applied. We discuss results for silicon piezoresistors fabricated by epitaxy and diffusion, but the method can be applied to any dopant profile or material which can be modeled in a similar fashion or extended to other microelectromechanical systems. PMID:19865512

Design of an MR image processing module on an FPGA chip

PubMed Central

Li, Limin; Wyrwicz, Alice M.

2015-01-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128 × 128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments. PMID:25909646

Development of Ion Chemosensors Based on Porphyrin Analogues.

PubMed

Ding, Yubin; Zhu, Wei-Hong; Xie, Yongshu

2017-02-22

Sensing of metal ions and anions is of great importance because of their widespread distribution in environmental systems and biological processes. Colorimetric and fluorescent chemosensors based on organic molecular species have been demonstrated to be effective for the detection of various ions and possess the significant advantages of low cost, high sensitivity, and convenient implementation. Of the available classes of organic molecules, porphyrin analogues possess inherently many advantageous features, making them suitable for the design of ion chemosensors, with the targeted sensing behavior achieved and easily modulated based on their following characteristics: (1) NH moieties properly disposed for binding of anions through cooperative hydrogen-bonding interactions; (2) multiple pyrrolic N atoms or other heteroatoms for selectively chelating metal ions; (3) variability of macrocycle size and peripheral substitution for modulation of ion selectivity and sensitivity; and (4) tunable near-infrared emission and good biocompatibility. In this Review, design strategies, sensing mechanisms, and sensing performance of ion chemosensors based on porphyrin analogues are described by use of extensive examples. Ion chemosensors based on normal porphyrins and linear oligopyrroles are also briefly described. This Review provides valuable information for researchers of related areas and thus may inspire the development of more practical and effective approaches for designing high-performance ion chemosensors based on porphyrin analogues and other relevant compounds.

Breckinridge Project, initial effort. Report XI, Volume V. Critical review of the design basis. [Critical review

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1982-01-01

Report XI, Technical Audit, is a compendium of research material used during the Initial Effort in making engineering comparisons and decisions. Volumes 4 and 5 of Report XI present those studies which provide a Critical Review of the Design Basis. The Critical Review Report, prepared by Intercontinental Econergy Associates, Inc., summarizes findings from an extensive review of the data base for the H-Coal process design. Volume 4 presents this review and assessment, and includes supporting material; specifically, Design Data Tabulation (Appendix A), Process Flow Sheets (Appendix B), and References (Appendix C). Volume 5 is a continuation of the references ofmore » Appendix C. Studies of a proprietary nature are noted and referenced, but are not included in these volumes. They are included in the Limited Access versions of these reports and may be reviewed by properly cleared personnel in the offices of Ashland Synthetic Fuels, Inc.« less

Design of High Speed and Low Offset Dynamic Latch Comparator in 0.18 µm CMOS Process

PubMed Central

Rahman, Labonnah Farzana; Reaz, Mamun Bin Ibne; Yin, Chia Chieu; Ali, Mohammad Alauddin Mohammad; Marufuzzaman, Mohammad

2014-01-01

The cross-coupled circuit mechanism based dynamic latch comparator is presented in this research. The comparator is designed using differential input stages with regenerative S-R latch to achieve lower offset, lower power, higher speed and higher resolution. In order to decrease circuit complexity, a comparator should maintain power, speed, resolution and offset-voltage properly. Simulations show that this novel dynamic latch comparator designed in 0.18 µm CMOS technology achieves 3.44 mV resolution with 8 bit precision at a frequency of 50 MHz while dissipating 158.5 µW from 1.8 V supply and 88.05 µA average current. Moreover, the proposed design propagates as fast as 4.2 nS with energy efficiency of 0.7 fJ/conversion-step. Additionally, the core circuit layout only occupies 0.008 mm2. PMID:25299266

Exploratory research for the development of a computer aided software design environment with the software technology program

NASA Technical Reports Server (NTRS)

Hardwick, Charles

1991-01-01

Field studies were conducted by MCC to determine areas of research of mutual interest to MCC and JSC. NASA personnel from the Information Systems Directorate and research faculty from UHCL/RICIS visited MCC in Austin, Texas to examine tools and applications under development in the MCC Software Technology Program. MCC personnel presented workshops in hypermedia, design knowledge capture, and design recovery on site at JSC for ISD personnel. The following programs were installed on workstations in the Software Technology Lab, NASA/JSC: (1) GERM (Graphic Entity Relations Modeler); (2) gIBIS (Graphic Issues Based Information System); and (3) DESIRE (Design Recovery tool). These applications were made available to NASA for inspection and evaluation. Programs developed in the MCC Software Technology Program run on the SUN workstation. The programs do not require special configuration, but they will require larger than usual amounts of disk space and RAM to operate properly.

Mechanism Design and Testing of a Self-Deploying Structure Using Flexible Composite Tape Springs

NASA Technical Reports Server (NTRS)

Footdale, Joseph N.; Murphey, Thomas W.

2014-01-01

The detailed mechanical design of a novel deployable support structure that positions and tensions a membrane optic for space imagining applications is presented. This is a complex three-dimensional deployment using freely deploying rollable composite tape spring booms that become load bearing structural members at full deployment. The deployment tests successfully demonstrate a new architecture based on rolled and freely deployed composite tape spring members that achieve simultaneous deployment without mechanical synchronization. Proper design of the flexible component mounting interface and constraint systems, which were critical in achieving a functioning unit, are described. These flexible composite components have much potential for advancing the state of the art in deployable structures, but have yet to be widely adopted. This paper demonstrates the feasibility and advantages of implementing flexible composite components, including the design details on how to integrate with required traditional mechanisms.

Design of an autonomous Lunar construction utility vehicle

NASA Technical Reports Server (NTRS)

Ash, Robert L.; Chew, Mason; Dixon, Iain (Editor)

1990-01-01

In order to prepare a site for a manned lunar base, an autonomously operated construction vehicle is necessary. A Lunar Construction Utility Vehicle (LCUV), which utilizes interchangeable construction implements, was designed conceptually. Some elements of the machine were studied in greater detail. Design of an elastic loop track system has advanced to the testing stage. A standard coupling device was designed to insure a proper connection between the different construction tools and the LCUV. Autonomous control of the track drive motors was simulated successfully through the use of a joystick and computer interface. A study of hydrogen-oxygen fuel cells has produced estimates of reactant and product size requirements and identified multi-layer insulation techniques. Research on a 100 kW heat rejection system has determined that it is necessary to house a radiator panel on a utility trailer. The impact of a 720 hr use cycle has produced a very large logistical support lien which requires further study.

A robust approach to optimal matched filter design in ultrasonic non-destructive evaluation (NDE)

NASA Astrophysics Data System (ADS)

Li, Minghui; Hayward, Gordon

2017-02-01

The matched filter was demonstrated to be a powerful yet efficient technique to enhance defect detection and imaging in ultrasonic non-destructive evaluation (NDE) of coarse grain materials, provided that the filter was properly designed and optimized. In the literature, in order to accurately approximate the defect echoes, the design utilized the real excitation signals, which made it time consuming and less straightforward to implement in practice. In this paper, we present a more robust and flexible approach to optimal matched filter design using the simulated excitation signals, and the control parameters are chosen and optimized based on the real scenario of array transducer, transmitter-receiver system response, and the test sample, as a result, the filter response is optimized and depends on the material characteristics. Experiments on industrial samples are conducted and the results confirm the great benefits of the method.

Optimum bus headway for preemption : a simulation approach

DOT National Transportation Integrated Search

1997-01-01

Preemption techniques are designed to provide preferential treatment for buses at signalized intersections. A preemption strategy, if properly designed, can provide continuous green phases for buses at successive intersections, thereby reducing trave...

Organizing a breast cancer database: data management.

PubMed

Yi, Min; Hunt, Kelly K

2016-06-01

Developing and organizing a breast cancer database can provide data and serve as valuable research tools for those interested in the etiology, diagnosis, and treatment of cancer. Depending on the research setting, the quality of the data can be a major issue. Assuring that the data collection process does not contribute inaccuracies can help to assure the overall quality of subsequent analyses. Data management is work that involves the planning, development, implementation, and administration of systems for the acquisition, storage, and retrieval of data while protecting it by implementing high security levels. A properly designed database provides you with access to up-to-date, accurate information. Database design is an important component of application design. If you take the time to design your databases properly, you'll be rewarded with a solid application foundation on which you can build the rest of your application.

Design and Parametric Study of the Magnetic Sensor for Position Detection in Linear Motor Based on Nonlinear Parametric Model Order Reduction

PubMed Central

Paul, Sarbajit; Chang, Junghwan

2017-01-01

This paper presents a design approach for a magnetic sensor module to detect mover position using the proper orthogonal decomposition-dynamic mode decomposition (POD-DMD)-based nonlinear parametric model order reduction (PMOR). The parameterization of the sensor module is achieved by using the multipolar moment matching method. Several geometric variables of the sensor module are considered while developing the parametric study. The operation of the sensor module is based on the principle of the airgap flux density distribution detection by the Hall Effect IC. Therefore, the design objective is to achieve a peak flux density (PFD) greater than 0.1 T and total harmonic distortion (THD) less than 3%. To fulfill the constraint conditions, the specifications for the sensor module is achieved by using POD-DMD based reduced model. The POD-DMD based reduced model provides a platform to analyze the high number of design models very fast, with less computational burden. Finally, with the final specifications, the experimental prototype is designed and tested. Two different modes, 90° and 120° modes respectively are used to obtain the position information of the linear motor mover. The position information thus obtained are compared with that of the linear scale data, used as a reference signal. The position information obtained using the 120° mode has a standard deviation of 0.10 mm from the reference linear scale signal, whereas the 90° mode position signal shows a deviation of 0.23 mm from the reference. The deviation in the output arises due to the mechanical tolerances introduced into the specification during the manufacturing process. This provides a scope for coupling the reliability based design optimization in the design process as a future extension. PMID:28671580

Design and Parametric Study of the Magnetic Sensor for Position Detection in Linear Motor Based on Nonlinear Parametric model order reduction.

PubMed

Paul, Sarbajit; Chang, Junghwan

2017-07-01

This paper presents a design approach for a magnetic sensor module to detect mover position using the proper orthogonal decomposition-dynamic mode decomposition (POD-DMD)-based nonlinear parametric model order reduction (PMOR). The parameterization of the sensor module is achieved by using the multipolar moment matching method. Several geometric variables of the sensor module are considered while developing the parametric study. The operation of the sensor module is based on the principle of the airgap flux density distribution detection by the Hall Effect IC. Therefore, the design objective is to achieve a peak flux density (PFD) greater than 0.1 T and total harmonic distortion (THD) less than 3%. To fulfill the constraint conditions, the specifications for the sensor module is achieved by using POD-DMD based reduced model. The POD-DMD based reduced model provides a platform to analyze the high number of design models very fast, with less computational burden. Finally, with the final specifications, the experimental prototype is designed and tested. Two different modes, 90° and 120° modes respectively are used to obtain the position information of the linear motor mover. The position information thus obtained are compared with that of the linear scale data, used as a reference signal. The position information obtained using the 120° mode has a standard deviation of 0.10 mm from the reference linear scale signal, whereas the 90° mode position signal shows a deviation of 0.23 mm from the reference. The deviation in the output arises due to the mechanical tolerances introduced into the specification during the manufacturing process. This provides a scope for coupling the reliability based design optimization in the design process as a future extension.

Selection of the battery pack parameters for an electric vehicle based on performance requirements

NASA Astrophysics Data System (ADS)

Koniak, M.; Czerepicki, A.

2017-06-01

Each type of vehicle has specific power requirements. Some require a rapid charging, other make long distances between charges, but a common feature is the longest battery life time. Additionally, the battery is influenced by factors such as temperature, depth of discharge and the operation current. The article contain the parameters of chemical cells that should be taken into account during the design of the battery for a specific application. This is particularly important because the batteries are not properly matched and can wear prematurely and cause an additional costs. The method of selecting the correct cell type should take previously discussed features and operating characteristics of the vehicle into account. The authors present methods of obtaining such characteristics along with their assessment and examples. Also there has been described an example of the battery parameters selection based on design assumptions of the vehicle and the expected performance characteristics. Selecting proper battery operating parameters is important due to its impact on the economic result of investments in electric vehicles. For example, for some Li-Ion technologies, the earlier worn out of batteries in a fleet of cruise boats or buses having estimated lifetime of 10 years is not acceptable, because this will cause substantial financial losses for the owner of the rolling stock. The presented method of choosing the right cell technology in the selected application, can be the basis for making the decision on future battery technical parameters.

Lighting for Schools.

ERIC Educational Resources Information Center

Benya, James R.

This publication highlights some of the benefits of proper daylighting design in educational facilities, discusses energy efficient electric lighting choices schools can make that are long lasting and require little maintenance, and offers six steps for designing lighting systems that use half the energy of earlier conventional designs. Several…

Evaluation of hot mix asphalt moisture sensitivity using the Nottingham Asphalt test equipment : final report, March 2010.

DOT National Transportation Integrated Search

2010-03-01

Pavements are subjected to different stresses during their design lives. A properly designed pavement will perform adequately during its : design life, and the distresses will not exceed the allowable limits; however, there are several factures that ...

Recreating Liberal Education: Student-Designed Programming after a Decade.

ERIC Educational Resources Information Center

Smith, Mark; Clarke, John

1980-01-01

Though student-designed programs have been justified by references to humanism, systems theory, and romantic idealism, a more secure foundation lies in developmental theory. When properly advised, it is suggested, student-designed programs resemble the most desirable processes of liberal education. (Author/MLW)

A framework for reporting on human factor/usability studies of health information technologies.

PubMed

Peute, Linda W; Driest, Keiko F; Marcilly, Romaric; Bras Da Costa, Sabrina; Beuscart-Zephir, Marie-Catherine; Jaspers, Monique W M

2013-01-01

Increasingly, studies are being published on the potential negative effect of introducing poor designed Health Information Technology (HIT) into clinical settings, relating to technology-induced errors and adverse events. Academic research on HIT design and evaluation is an extremely important source of information in providing new insights into factors contributing to successful system (re)design efforts, system user-friendliness and usability issues and safety critical aspects of HIT design. However, these studies have been inconsistent and incomprehensive in their reporting, complicating the appraisal of outcomes, generalizability of study findings, meta-analysis and harmonization of the available evidence. To improve identification of type of use errors and safety related issues regarding design and implementation of HIT, consensus on issues to be reported on in scientific publications is a necessary step forward. This study presents the first approach to a framework providing a set of principles to follow for comprehensive and unambiguous reporting of HIT design and usability evaluation studies with the objective to reduce variation, improve on the publication reporting quality and proper indexation of these studies. This framework may be helpful in expanding the knowledge base not only concerning the application of Human Factors (HF)/Usability studies of HIT but also improve the knowledge base of how to (re)design and implement effective, efficient and safe HIT.

Design Process-System and Methodology of Design Research

NASA Astrophysics Data System (ADS)

Bashier, Fathi

2017-10-01

Studies have recognized the failure of the traditional design approach both in practice and in the studio. They showed that design problems today are too complex for the traditional approach to cope with and reflected a new interest in a better quality design services in order to meet the challenges of our time. In the mid-1970s and early 1980s, there has been a significant shift in focus within the field of design research towards the aim of creating a ‘design discipline’. The problem, as will be discussed, is the lack of an integrated theory of design knowledge that can explicitly describe the design process in a coherent way. As a consequence, the traditional approach fails to operate systematically, in a disciplinary manner. Addressing this problem is the primary goal of the research study in the design process currently being conducted in the research-based master studio at Wollega University, Ethiopia. The research study seeks to make a contribution towards a disciplinary approach, through proper understanding the mechanism of knowledge development within design process systems. This is the task of the ‘theory of design knowledge’. In this article the research project is introduced, and a model of the design process-system is developed in the studio as a research plan and a tool of design research at the same time. Based on data drawn from students’ research projects, the theory of design knowledge is developed and empirically verified through the research project.

Numerically based design of an orifice plate flowmetering system for human respiratory flow monitoring.

PubMed

Fortuna, A O; Gurd, J R

1999-01-01

During certain medical procedures, it is important to continuously measure the respiratory flow of a patient, as lack of proper ventilation can cause brain damage and ultimately death. The monitoring of the ventilatory condition of a patient is usually performed with the aid of flowmeters. However, water and other secretions present in the expired air can build up and ultimately block a traditional, restriction-based flowmeter; by using an orifice plate flowmeter, such blockages are minimized. This paper describes the design of an orifice plate flowmetering system including, especially, a description of the numerical and computational techniques adopted in order to simulate human respiratory and sinusoidal air flow across various possible designs for the orifice plate flowmeter device. Parallel computation and multigrid techniques were employed in order to reduce execution time. The simulated orifice plate was later built and tested under unsteady sinusoidal flows. Experimental tests show reasonable agreement with the numerical simulation, thereby reinforcing the general hypothesis that computational exploration of the design space is sufficiently accurate to allow designers of such systems to use this in preference to the more traditional, mechanical prototyping techniques.

46 CFR 58.30-5 - Design requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Design requirements. 58.30-5 Section 58.30-5 Shipping... AND RELATED SYSTEMS Fluid Power and Control Systems § 58.30-5 Design requirements. (a) The.... (b) The system shall be so designed that proper functioning of any unit shall not be affected by the...

46 CFR 58.30-5 - Design requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Design requirements. 58.30-5 Section 58.30-5 Shipping... AND RELATED SYSTEMS Fluid Power and Control Systems § 58.30-5 Design requirements. (a) The.... (b) The system shall be so designed that proper functioning of any unit shall not be affected by the...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 12 2013-01-01 2013-01-01 false Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 12 2012-01-01 2012-01-01 false Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 12 2011-01-01 2011-01-01 false Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 12 2014-01-01 2013-01-01 true Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

Design for Review - Applying Lessons Learned to Improve the FPGA Review Process

NASA Technical Reports Server (NTRS)

Figueiredo, Marco A.; Li, Kenneth E.

2014-01-01

Flight Field Programmable Gate Array (FPGA) designs are required to be independently reviewed. This paper provides recommendations to Flight FPGA designers to properly prepare their designs for review in order to facilitate the review process, and reduce the impact of the review time in the overall project schedule.

Considerations for the Optimal Design of a Two-Way Interactive Distance Education Classroom.

ERIC Educational Resources Information Center

Gregg, Joe; Persichitte, Kay

To make effective use of a two-way interactive distance education system, classroom design should be a primary consideration. A properly designed classroom will enhance content objectives and increase acceptance of this type of instructional delivery. This paper describes key considerations for optimal design. Construction considerations include…

Manufacturing and Cost Considerations in Multidisciplinary Aircraft Design (Research on Mathematical Modeling of Manufacturability Factors)

NASA Technical Reports Server (NTRS)

Rais-Rohani, Masoud

1996-01-01

The identification of airframe Manufacturability Factors/Cost Drivers (MFCD) and the method by which the relationships between MFCD and designer-controlled parameters could be properly modeled are described.

Design of limited-stop service based on the degree of unbalance of passenger demand

PubMed Central

2018-01-01

This paper presents a limited-stop service for a bus fleet to meet the unbalanced demand of passengers on a bus route and to improve the transit service of the bus route. This strategy includes two parts: a degree assessment of unbalanced passenger demand and an optimization of the limited-stop service. The degree assessment of unbalanced passenger demand, which is based on the different passenger demand between stations and the unbalance of passengers within the station, is used to judge whether implementing the limited-stop service is necessary for a bus route. The optimization of limited-stop service considers the influence of stop skipping action and bus capacity on the left-over passengers to determine the proper skipping stations for the bus fleet serving the entire route by minimizing both the waiting time and in-vehicle time of passengers and the running time of vehicles. A solution algorithm based on genetic algorithm is also presented to evaluate the degree of unbalanced passenger demand and optimize the limited-stop scheme. Then, the proper strategy is tested on a bus route in Changchun city of China. The threshold of degree assessment of unbalanced passenger demand can be calibrated and adapted to different passenger demands. PMID:29505585

Design of limited-stop service based on the degree of unbalance of passenger demand.

PubMed

Zhang, Hu; Zhao, Shuzhi; Liu, Huasheng; Liang, Shidong

2018-01-01

This paper presents a limited-stop service for a bus fleet to meet the unbalanced demand of passengers on a bus route and to improve the transit service of the bus route. This strategy includes two parts: a degree assessment of unbalanced passenger demand and an optimization of the limited-stop service. The degree assessment of unbalanced passenger demand, which is based on the different passenger demand between stations and the unbalance of passengers within the station, is used to judge whether implementing the limited-stop service is necessary for a bus route. The optimization of limited-stop service considers the influence of stop skipping action and bus capacity on the left-over passengers to determine the proper skipping stations for the bus fleet serving the entire route by minimizing both the waiting time and in-vehicle time of passengers and the running time of vehicles. A solution algorithm based on genetic algorithm is also presented to evaluate the degree of unbalanced passenger demand and optimize the limited-stop scheme. Then, the proper strategy is tested on a bus route in Changchun city of China. The threshold of degree assessment of unbalanced passenger demand can be calibrated and adapted to different passenger demands.

Designing and assessing fixed dental prostheses 2 multimedia-based education in dentistry students.

PubMed

Jahandideh, Yousef; Roohi Balasi, Leila; Vadiati Saberi, Bardia; Dadgaran, Ideh

2016-01-01

Background: Above all methods effective learning results from decent training, acquired in the proper environment and encouraging creative methods. Computer-assisted training by educational software is considered a fundamental measure to improve medical and dentistry education systems. This study aims to design and assess fixed dental prostheses via 2 multimedia instructional contents at the Guilan dentistry school. Methods: This is a descriptive and cross-sectional study. First off, the instructional content was analyzed. The software used to produce multimedia was the iSpring suite Ver.7.0. After designing the instructional multimedia, this software was loaded by LMS. Sixty-nine dentistry students in the 5th semester at Guilan Dentistry School were selected via convenience sampling. At the end of the course, a structured questionnaire containing 26 items were handed to the students to evaluate the instructional multimedia quality. Results: Mean ±SD age was 24.68±3.24 years, 43 were women (62.4%) and 26 were men (37.6%) -the majority of 76.8% used the internet at home. A portion of 33.3% were inclined to use multimedia and the internet with in-person training. About 60% declared that multimedia quality as being good. Conclusion: the instructional multimedia designs which are compatible with lesson objectives and audiovisual facilities can have a great effect on the student's satisfaction. Preparing instructional multimedia makes the instructional content easily accessible for students to be able to review it several times at the proper opportunity and if presented through LMS they would be able to study the lesson subject wherever and whenever accessing the internet.

Phased-array sources based on nonlinear metamaterial nanocavities

PubMed Central

Wolf, Omri; Campione, Salvatore; Benz, Alexander; Ravikumar, Arvind P.; Liu, Sheng; Luk, Ting S.; Kadlec, Emil A.; Shaner, Eric A.; Klem, John F.; Sinclair, Michael B.; Brener, Igal

2015-01-01

Coherent superposition of light from subwavelength sources is an attractive prospect for the manipulation of the direction, shape and polarization of optical beams. This phenomenon constitutes the basis of phased arrays, commonly used at microwave and radio frequencies. Here we propose a new concept for phased-array sources at infrared frequencies based on metamaterial nanocavities coupled to a highly nonlinear semiconductor heterostructure. Optical pumping of the nanocavity induces a localized, phase-locked, nonlinear resonant polarization that acts as a source feed for a higher-order resonance of the nanocavity. Varying the nanocavity design enables the production of beams with arbitrary shape and polarization. As an example, we demonstrate two second harmonic phased-array sources that perform two optical functions at the second harmonic wavelength (∼5 μm): a beam splitter and a polarizing beam splitter. Proper design of the nanocavity and nonlinear heterostructure will enable such phased arrays to span most of the infrared spectrum. PMID:26126879

Verification of NASA Emergent Systems

NASA Technical Reports Server (NTRS)

Rouff, Christopher; Vanderbilt, Amy K. C. S.; Truszkowski, Walt; Rash, James; Hinchey, Mike

2004-01-01

NASA is studying advanced technologies for a future robotic exploration mission to the asteroid belt. This mission, the prospective ANTS (Autonomous Nano Technology Swarm) mission, will comprise of 1,000 autonomous robotic agents designed to cooperate in asteroid exploration. The emergent properties of swarm type missions make them powerful, but at the same time are more difficult to design and assure that the proper behaviors will emerge. We are currently investigating formal methods and techniques for verification and validation of future swarm-based missions. The advantage of using formal methods is their ability to mathematically assure the behavior of a swarm, emergent or otherwise. The ANT mission is being used as an example and case study for swarm-based missions for which to experiment and test current formal methods with intelligent swam. Using the ANTS mission, we have evaluated multiple formal methods to determine their effectiveness in modeling and assuring swarm behavior.

Rational Improvement of Molar Absorptivity Guided by Oscillator Strength: A Case Study with Furoindolizine-Based Core Skeleton.

PubMed

Lee, Youngjun; Jo, Ala; Park, Seung Bum

2015-12-21

The rational improvement of photophysical properties can be highly valuable for the discovery of novel organic fluorophores. Using our new design strategy guided by the oscillator strength, we developed a series of full-color-tunable furoindolizine analogs with improved molar absorptivity through the fusion of a furan ring into the indolizine-based Seoul fluorophore. The excellent correlation between the computable values (oscillator strength and theoretical S0 -S1 energy gap) and photophysical properties (molar absorptivity and emission wavelength) confirmed the effectualness of our design strategy. © 2015 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA. This is an open access article under the terms of the Creative Commons Attribution Non-Commercial NoDerivs License, which permits use and distribution in any medium, provided the original work is properly cited, the use is non-commercial and no modifications or adaptations are made.

Giant optical field enhancement in multi-dielectric stacks by photon scanning tunneling microscopy

NASA Astrophysics Data System (ADS)

Ndiaye, C.; Zerrad, M.; Lereu, A. L.; Roche, R.; Dumas, Ph.; Lemarchand, F.; Amra, C.

2013-09-01

Dielectric optical thin films, as opposed to metallic, have been very sparsely explored as good candidates for absorption-based optical field enhancement. In such materials, the low imaginary part of the refractive index implies that absorption processes are usually not predominant. This leads to dielectric-based optical resonances mainly via waveguiding modes. We show here that when properly designed, a multi-layered dielectric thin films stack can give rise to optical resonances linked to total absorption. We report here, on such dielectric stack designed to possess a theoretical optical field enhancement above 1000. Using photon scanning tunneling microscopy, we experimentally evaluate the resulting field enhancement of the stack as well as the associated penetration depth. We thus demonstrate the capability of multi-dielectric stacks in generating giant optical field with tunable penetration depth (down to few dozens of nm).

Computational Design Tool for Bridge Hydrodynamic Loading in Inundated Flows of Midwest Rivers

DOT National Transportation Integrated Search

2009-12-01

The hydraulic forces experienced by an inundated bridge deck have great importance in the design of bridges. The proper estimation of loading exerted by the flow on the structure is important for design plans and is pertinent for evaluating its vulne...

Manufacture of threads with variable pitch by using noncircular gears

NASA Astrophysics Data System (ADS)

Slătineanu, L.; Dodun, O.; Coteață, M.; Coman, I.; Nagîț, G.; Beșliu, I.

2016-08-01

There are mechanical equipments in which shafts threaded with variable pitch are included. Such a shaft could be met in the case of worm specific to the double enveloping worm gearing. Over the years, the researchers investigated some possibilities to geometrically define and manufacture the shaft zones characterized by a variable pitch. One of the methods able to facilitate the manufacture of threads with variable pitch is based on the use of noncircular gears in the threading kinematic chain for threading by cutting. In order to design the noncircular gears, the mathematical law of pitch variation has to be known. An analysis of pitch variation based on geometrical considerations was developed in the case of a double enveloping globoid worm. Subsequently, on the bases of a proper situation, a numerical model was determined. In this way, an approximately law of pitch variation was determined and it could be taken into consideration when designing the noncircular gears included in the kinematic chain of the cutting machine tool.

Ordering Design Tasks Based on Coupling Strengths

NASA Technical Reports Server (NTRS)

Rogers, J. L.; Bloebaum, C. L.

1994-01-01

The design process associated with large engineering systems requires an initial decomposition of the complex system into modules of design tasks which are coupled through the transference of output data. In analyzing or optimizing such a coupled system, it is essential to be able to determine which interactions figure prominently enough to significantly affect the accuracy of the system solution. Many decomposition approaches assume the capability is available to determine what design tasks and interactions exist and what order of execution will be imposed during the analysis process. Unfortunately, this is often a complex problem and beyond the capabilities of a human design manager. A new feature for DeMAID (Design Manager's Aid for Intelligent Decomposition) will allow the design manager to use coupling strength information to find a proper sequence for ordering the design tasks. In addition, these coupling strengths aid in deciding if certain tasks or couplings could be removed (or temporarily suspended) from consideration to achieve computational savings without a significant loss of system accuracy. New rules are presented and two small test cases are used to show the effects of using coupling strengths in this manner.

Ordering design tasks based on coupling strengths

NASA Technical Reports Server (NTRS)

Rogers, James L., Jr.; Bloebaum, Christina L.

1994-01-01

The design process associated with large engineering systems requires an initial decomposition of the complex system into modules of design tasks which are coupled through the transference of output data. In analyzing or optimizing such a coupled system, it is essential to be able to determine which interactions figure prominently enough to significantly affect the accuracy of the system solution. Many decomposition approaches assume the capability is available to determine what design tasks and interactions exist and what order of execution will be imposed during the analysis process. Unfortunately, this is often a complex problem and beyond the capabilities of a human design manager. A new feature for DeMAID (Design Manager's Aid for Intelligent Decomposition) will allow the design manager to use coupling strength information to find a proper sequence for ordering the design tasks. In addition, these coupling strengths aid in deciding if certain tasks or couplings could be removed (or temporarily suspended) from consideration to achieve computational savings without a significant loss of system accuracy. New rules are presented and two small test cases are used to show the effects of using coupling strengths in this manner.

REACT: Resettable Hold Down and Release Actuator for Space Applications

NASA Astrophysics Data System (ADS)

Nava, Nestor; Collado, Marcelo; Cabás, Ramiro

2014-07-01

A new HDRA based on SMA technology, called REACT, has been designed for development of loads and appendixes in space applications. This design involves a rod supported by spheres that block its axial movement during a preload application. The rod shape allows misalignment and blocks the rotation around axial axis for a proper installation of the device. Because of the high preload requirements for this type of actuators, finite element analysis (FEA) has been developed in order to check the structure resistance. The results of the FEA have constrained the REACT design, in terms of dimensions, materials, and shape of the mechanical parts. A complete test campaign for qualification of REACT is proposed. Several qualification models are intended to be built for testing in parallel. Therefore, it is a way to demonstrate margins which allows getting some statistics.

Design of an autonomous lunar construction utility vehicle

NASA Technical Reports Server (NTRS)

1990-01-01

In order to prepare a site for a lunar base, an autonomously operated construction vehicle is necessary. Discussed here is a Lunar Construction Utility Vehicle (LCUV), which uses interchangeable construction implements. Design of an elastic loop track system has advanced to the testing stage. A standard coupling device has been designed to insure a proper connection between the different construction tools and the LCUV. Autonomous control of the track drive motors was simulated successfully through the use of a joystick and a computer interface. A study of hydrogen-oxygen fuel cells produced estimates of reactant and product requirements and identified multilayer insulation needs. Research on the 100-kW heat rejection system determined that it is necessary to transport the radiator panel on a utility trailer. Extensive logistical support for the 720 hour use cycle requires further study.

Optimization of Design Parameters and Operating Conditions of Electrochemical Capacitors for High Energy and Power Performance

NASA Astrophysics Data System (ADS)

Ike, Innocent S.; Sigalas, Iakovos; Iyuke, Sunny E.

2017-03-01

Theoretical expressions for performance parameters of different electrochemical capacitors (ECs) have been optimized by solving them using MATLAB scripts as well as via the MATLAB R2014a optimization toolbox. The performance of the different kinds of ECs under given conditions was compared using theoretical equations and simulations of various models based on the conditions of device components, using optimal values for the coefficient associated with the battery-kind material ( K BMopt) and the constant associated with the electrolyte material ( K Eopt), as well as our symmetric electric double-layer capacitor (EDLC) experimental data. Estimation of performance parameters was possible based on values for the mass ratio of electrodes, operating potential range ratio, and specific capacitance of electrolyte. The performance of asymmetric ECs with suitable electrode mass and operating potential range ratios using aqueous or organic electrolyte at appropriate operating potential range and specific capacitance was 2.2 and 5.56 times greater, respectively, than for the symmetric EDLC and asymmetric EC using the same aqueous electrolyte, respectively. This enhancement was accompanied by reduced cell mass and volume. Also, the storable and deliverable energies of the asymmetric EC with suitable electrode mass and operating potential range ratios using the proper organic electrolyte were 12.9 times greater than those of the symmetric EDLC using aqueous electrolyte, again with reduced cell mass and volume. The storable energy, energy density, and power density of the asymmetric EDLC with suitable electrode mass and operating potential range ratios using the proper organic electrolyte were 5.56 times higher than for a similar symmetric EDLC using aqueous electrolyte, with cell mass and volume reduced by a factor of 1.77. Also, the asymmetric EDLC with the same type of electrode and suitable electrode mass ratio, working potential range ratio, and proper organic electrolyte showed enhanced performance compared with the conventional symmetric EDLC using aqueous electrolyte, with reduced cell mass and volume. These results can obviously reduce the number of experiments required to determine the optimum manufacturing design for ECs and also demonstrate that use of an asymmetric electrode and organic electrolyte was very successful for improving the performance of the EC, with reduced cell mass and volume. These results can also act as guidelines for design, fabrication, and operation of electrochemical capacitors with outstanding storable energy, energy density, and power density.

Finite Element Based HWB Centerbody Structural Optimization and Weight Prediction

NASA Technical Reports Server (NTRS)

Gern, Frank H.

2012-01-01

This paper describes a scalable structural model suitable for Hybrid Wing Body (HWB) centerbody analysis and optimization. The geometry of the centerbody and primary wing structure is based on a Vehicle Sketch Pad (VSP) surface model of the aircraft and a FLOPS compatible parameterization of the centerbody. Structural analysis, optimization, and weight calculation are based on a Nastran finite element model of the primary HWB structural components, featuring centerbody, mid section, and outboard wing. Different centerbody designs like single bay or multi-bay options are analyzed and weight calculations are compared to current FLOPS results. For proper structural sizing and weight estimation, internal pressure and maneuver flight loads are applied. Results are presented for aerodynamic loads, deformations, and centerbody weight.

Design and implementation of projects with Xilinx Zynq FPGA: a practical case

NASA Astrophysics Data System (ADS)

Travaglini, R.; D'Antone, I.; Meneghini, S.; Rignanese, L.; Zuffa, M.

The main advantage when using FPGAs with embedded processors is the availability of additional several high-performance resources in the same physical device. Moreover, the FPGA programmability allows for connect custom peripherals. Xilinx have designed a programmable device named Zynq-7000 (simply called Zynq in the following), which integrates programmable logic (identical to the other Xilinx "serie 7" devices) with a System on Chip (SOC) based on two embedded ARM processors. Since both parts are deeply connected, the designers benefit from performance of hardware SOC and flexibility of programmability as well. In this paper a design developed by the Electronic Design Department at the Bologna Division of INFN will be presented as a practical case of project based on Zynq device. It is developed by using a commercial board called ZedBoard hosting a FMC mezzanine with a 12-bit 500 MS/s ADC. The Zynq FPGA on the ZedBoard receives digital outputs from the ADC and send them to the acquisition PC, after proper formatting, through a Gigabit Ethernet link. The major focus of the paper will be about the methodology to develop a Zynq-based design with the Xilinx Vivado software, enlightening how to configure the SOC and connect it with the programmable logic. Firmware design techniques will be presented: in particular both VHDL and IP core based strategies will be discussed. Further, the procedure to develop software for the embedded processor will be presented. Finally, some debugging tools, like the embedded Logic Analyzer, will be shown. Advantages and disadvantages with respect to adopting FPGA without embedded processors will be discussed.

Fusing Horizons -- A Grammatical Design Approach for the Arts and Humanities: Using Rules, Contingency and Hermeneutics in Design Education

ERIC Educational Resources Information Center

Bruton, Dean

2007-01-01

This article argues that grammatical thinking within a framework of phenomenological hermeneutics assists designing and may properly be used as a fundamental teaching approach for an interdisciplinary art and design studio. Furthermore, it argues that the theme of grammatical design awareness could be considered as a generic issue across all…

Small Orbital Stereo Tracking Camera Technology Development

NASA Technical Reports Server (NTRS)

Bryan, Tom; Macleod, Todd; Gagliano, Larry

2015-01-01

On-Orbit Small Debris Tracking and Characterization is a technical gap in the current National Space Situational Awareness necessary to safeguard orbital assets and crew. This poses a major risk of MOD damage to ISS and Exploration vehicles. In 2015 this technology was added to NASA's Office of Chief Technologist roadmap. For missions flying in or assembled in or staging from LEO, the physical threat to vehicle and crew is needed in order to properly design the proper level of MOD impact shielding and proper mission design restrictions. Need to verify debris flux and size population versus ground RADAR tracking. Use of ISS for In-Situ Orbital Debris Tracking development provides attitude, power, data and orbital access without a dedicated spacecraft or restricted operations on-board a host vehicle as a secondary payload. Sensor Applicable to in-situ measuring orbital debris in flux and population in other orbits or on other vehicles. Could enhance safety on and around ISS. Some technologies extensible to monitoring of extraterrestrial debris as well to help accomplish this, new technologies must be developed quickly. The Small Orbital Stereo Tracking Camera is one such up and coming technology. It consists of flying a pair of intensified megapixel telephoto cameras to evaluate Orbital Debris (OD) monitoring in proximity of International Space Station. It will demonstrate on-orbit optical tracking (in situ) of various sized objects versus ground RADAR tracking and small OD models. The cameras are based on Flight Proven Advanced Video Guidance Sensor pixel to spot algorithms (Orbital Express) and military targeting cameras. And by using twin cameras we can provide Stereo images for ranging & mission redundancy. When pointed into the orbital velocity vector (RAM), objects approaching or near the stereo camera set can be differentiated from the stars moving upward in background.

Small Orbital Stereo Tracking Camera Technology Development

NASA Technical Reports Server (NTRS)

Bryan, Tom; MacLeod, Todd; Gagliano, Larry

2016-01-01

On-Orbit Small Debris Tracking and Characterization is a technical gap in the current National Space Situational Awareness necessary to safeguard orbital assets and crew. This poses a major risk of MOD damage to ISS and Exploration vehicles. In 2015 this technology was added to NASA's Office of Chief Technologist roadmap. For missions flying in or assembled in or staging from LEO, the physical threat to vehicle and crew is needed in order to properly design the proper level of MOD impact shielding and proper mission design restrictions. Need to verify debris flux and size population versus ground RADAR tracking. Use of ISS for In-Situ Orbital Debris Tracking development provides attitude, power, data and orbital access without a dedicated spacecraft or restricted operations on-board a host vehicle as a secondary payload. Sensor Applicable to in-situ measuring orbital debris in flux and population in other orbits or on other vehicles. Could enhance safety on and around ISS. Some technologies extensible to monitoring of extraterrestrial debris as well To help accomplish this, new technologies must be developed quickly. The Small Orbital Stereo Tracking Camera is one such up and coming technology. It consists of flying a pair of intensified megapixel telephoto cameras to evaluate Orbital Debris (OD) monitoring in proximity of International Space Station. It will demonstrate on-orbit optical tracking (in situ) of various sized objects versus ground RADAR tracking and small OD models. The cameras are based on Flight Proven Advanced Video Guidance Sensor pixel to spot algorithms (Orbital Express) and military targeting cameras. And by using twin cameras we can provide Stereo images for ranging & mission redundancy. When pointed into the orbital velocity vector (RAM), objects approaching or near the stereo camera set can be differentiated from the stars moving upward in background.

Texas flexible pavements and overlays : year 5 report - complete data documentation.

DOT National Transportation Integrated Search

2017-05-01

Proper calibration and validation of pavement design and performance models to Texas conditions is : essential for cost-effective flexible pavement design, performance predictions, and maintenance/rehab : strategies. The veracity of the calibration o...

Optimization of power and energy densities in supercapacitors

NASA Astrophysics Data System (ADS)

Robinson, David B.

Supercapacitors use nanoporous electrodes to store large amounts of charge on their high surface areas, and use the ions in electrolytes to carry charge into the pores. Their high power density makes them a potentially useful complement to batteries. However, ion transport through long, narrow channels still limits power and efficiency in these devices. Proper design can mitigate this. Current collector geometry must also be considered once this is done. Here, De Levie's model for porous electrodes is applied to quantitatively predict device performance and to propose optimal device designs for given specifications. Effects unique to nanoscale pores are considered, including that pores may not have enough salt to fully charge. Supercapacitors are of value for electric vehicles, portable electronics, and power conditioning in electrical grids with distributed renewable sources, and that value will increase as new device fabrication methods are developed and proper design accommodates those improvements. Example design outlines for vehicle applications are proposed and compared.

Combined Feature Based and Shape Based Visual Tracker for Robot Navigation

NASA Technical Reports Server (NTRS)

Deans, J.; Kunz, C.; Sargent, R.; Park, E.; Pedersen, L.

2005-01-01

We have developed a combined feature based and shape based visual tracking system designed to enable a planetary rover to visually track and servo to specific points chosen by a user with centimeter precision. The feature based tracker uses invariant feature detection and matching across a stereo pair, as well as matching pairs before and after robot movement in order to compute an incremental 6-DOF motion at each tracker update. This tracking method is subject to drift over time, which can be compensated by the shape based method. The shape based tracking method consists of 3D model registration, which recovers 6-DOF motion given sufficient shape and proper initialization. By integrating complementary algorithms, the combined tracker leverages the efficiency and robustness of feature based methods with the precision and accuracy of model registration. In this paper, we present the algorithms and their integration into a combined visual tracking system.

Effects of a Brief but Intensive Remedial Computer Intervention in a Sub-Sample of Kindergartners with Early Literacy Delays

ERIC Educational Resources Information Center

Van der Kooy-Hofland, Verna A. C.; Bus, Adriana G.; Roskos, Kathleen

2012-01-01

Living Letters is an adaptive game designed to promote children's combining of how the proper name sounds with their knowledge of how the name looks. A randomized controlled trial (RCT) was used to experimentally test whether priming for attending to the sound-symbol relationship in the proper name can reduce the risk for developing reading…

Shed a light of wireless technology on portable mobile design of NIRS

NASA Astrophysics Data System (ADS)

Sun, Yunlong; Li, Ting

2016-03-01

Mobile internet is growing rapidly driven by high-tech companies including the popular Apple and Google. The wireless mini-NIRS is believed to deserve a great spread future, while there is sparse report on wireless NIRS device and even for the reported wireless NIRS, its wireless design is scarcely presented. Here we focused on the wireless design of NIRS devices. The widely-used wireless communication standards and wireless communication typical solutions were employed into our NIRS design and then compared on communication efficiency, distance, error rate, low-cost, power consumption, and stabilities, based on the requirements of NIRS applications. The properly-performed wireless communication methods matched with the characteristics of NIRS are picked out. Finally, we realized one recommended wireless communication in our NIRS, developed a test platform on wireless NIRS and tested the full properties on wireless communication. This study elaborated the wireless communication methods specified for NIRS and suggested one implementation with one example fully illustrated, which support the future mobile design on NIRS devices.

Anthropometric evaluation of the Creches children furniture in Turkey.

PubMed

Barli, Onder; Sari, Reyhan Midilli; Elmali, Derya; Aydintan, Erkan

2006-12-01

The dimensions of the living and working space and buildings, the types of material and different riggings should be designed to conform to the users' anthropometric measures. The first requirement to design on ergonomic system is to measure the human being who will work and live in that system. Because of this, anthropometric measures are the most frequently used ergonomic data during the design process. In this research paper, we attempt to organize a new data base of anthropometric data to use in the design of children's equipment and furniture used in crèches. A starting point for research on the proper dimensions of creche furniture is to investigate how the dimensions of furniture reflect the body dimensions and the functional needs of the children using furniture. The anthropometric data of 3, 4 and 5 year-old-children in crèches was used. We report the results of the measurements of 18 anthropometric characteristics of children which constitute a set of basic data for the design of functional spaces and furniture.

An All-Sky Search for Wide Binaries in the SUPERBLINK Proper Motion Catalog

NASA Astrophysics Data System (ADS)

Hartman, Zachary; Lepine, Sebastien

2017-01-01

We present initial results from an all-sky search for Common Proper Motion (CPM) binaries in the SUPERBLINK all-sky proper motion catalog of 2.8 million stars with proper motions greater than 40 mas/yr, which has been recently enhanced with data from the GAIA mission. We initially search the SUPERBLINK catalog for pairs of stars with angular separations up to 1 degree and proper motion difference less than 40 mas/yr. In order to determine which of these pairs are real binaries, we develop a Bayesian analysis to calculate probabilities of true companionship based on a combination of proper motion magnitude, angular separation, and proper motion differences. The analysis reveals that the SUPERBLINK catalog most likely contains ~40,000 genuine common proper motion binaries. We provide initial estimates of the distances and projected physical separations of these wide binaries.

Analysis and optimization of Love wave liquid sensors.

PubMed

Jakoby, B; Vellekoop, M J

1998-01-01

Love wave sensors are highly sensitive microacoustic devices, which are well suited for liquid sensing applications thanks to the shear polarization of the wave. The sensing mechanism thereby relies on the mechanical (or acoustic) interaction of the device with the liquid. The successful utilization of Love wave devices for this purpose requires proper shielding to avoid unwanted electric interaction of the liquid with the wave and the transducers. In this work we describe the effects of this electric interaction and the proper design of a shield to prevent it. We present analysis methods, which illustrate the impact of the interaction and which help to obtain an optimized design of the proposed shield. We also present experimental results for devices that have been fabricated according to these design rules.

Project Management Approaches for Online Learning Design

ERIC Educational Resources Information Center

Eby, Gulsun; Yuzer, T. Volkan

2013-01-01

Developments in online learning and its design are areas that continue to grow in order to enhance students' learning environments and experiences. However, in the implementation of new technologies, the importance of properly and fairly overseeing these courses is often undervalued. "Project Management Approaches for Online Learning Design"…

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2013 CFR

2013-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2011 CFR

2011-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2014 CFR

2014-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2012 CFR

2012-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2010 CFR

2010-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

Design, construction, and evaluation of a 1:8 scale model binaural manikin.

PubMed

Robinson, Philip; Xiang, Ning

2013-03-01

Many experiments in architectural acoustics require presenting listeners with simulations of different rooms to compare. Acoustic scale modeling is a feasible means to create accurate simulations of many rooms at reasonable cost. A critical component in a scale model room simulation is a receiver that properly emulates a human receiver. For this purpose, a scale model artificial head has been constructed and tested. This paper presents the design and construction methods used, proper equalization procedures, and measurements of its response. A headphone listening experiment examining sound externalization with various reflection conditions is presented that demonstrates its use for psycho-acoustic testing.

Fully tunable 360° microwave photonic phase shifter based on a single semiconductor optical amplifier.

PubMed

Sancho, Juan; Lloret, Juan; Gasulla, Ivana; Sales, Salvador; Capmany, José

2011-08-29

A fully tunable microwave photonic phase shifter involving a single semiconductor optical amplifier (SOA) is proposed and demonstrated. 360° microwave phase shift has been achieved by tuning the carrier wavelength and the optical input power injected in an SOA while properly profiting from the dispersion feature of a conveniently designed notch filter. It is shown that the optical filter can be advantageously employed to switch between positive and negative microwave phase shifts. Numerical calculations corroborate the experimental results showing an excellent agreement.

Polarization characteristics of an altazimuth sky scanner

NASA Technical Reports Server (NTRS)

Garrison, L. M.; Blaszczak, Z.; Green, A. E. S.

1980-01-01

A theoretical description of the polarization characteristics of an altazimuth sky scanner optical system based on Mueller-Stokes calculus is presented. This computer-driven optical system was designed to perform laboratory studies of skylight and of celestial objects during day or night, and has no space limitations; however, the two parallel 45 deg tilt mirrors introduce some intrinsic polarization. Therefore, proper data interpretation requires a theoretical understanding of the polarization features of the instrument and accurate experimental determination of the Mueller-Stokes matrix elements describing the polarizing and depolarizing action of the system.

ASCAN Helms simulates parachute jump during VAFB training exercises

NASA Image and Video Library

1990-09-17

S90-48372 (29-31 July 1990) --- Mission specialist astronaut candidate Susan J. Helms simulates a parachute jump during a survival training course at Vance Air Force Base. She is one of 23 astronaut candidates from the Johnson Space Center who have joined military personnel for the special three-day training course. The course is designed to prepare the trainees for proper survival measures to take in the event of an emergency aboard the T-38 jet trainer aircraft they will frequently use once they become full-fledged astronauts.

LOUSMA, JACK R. - WATER SURVIVAL TRAINING - FL

NASA Image and Video Library

1978-07-31

S78-34037 (31 July 1978) --- Astronaut Jack R. Lousma, geared with a parachute, is pulled along behind a boat in Gulf waters at Homestead Air Force Base in Florida during a water survival training course attended by several NASA astronauts. The overall course is designed to familiarize astronauts with proper procedures to take in the event of ejection from an aircraft over water. Photo credit: NASA (NOTE: Since this photograph was made, astronaut Jack R. Lousma was named commander of STS-3, scheduled for launch in early spring of 1982.)

Beam Dynamics Simulation of Photocathode RF Electron Gun at the PBP-CMU Linac Laboratory

NASA Astrophysics Data System (ADS)

Buakor, K.; Rimjaem, S.

2017-09-01

Photocathode radio-frequency (RF) electron guns are widely used at many particle accelerator laboratories due to high quality of produced electron beams. By using a short-pulse laser to induce the photoemission process, the electrons are emitted with low energy spread. Moreover, the photocathode RF guns are not suffered from the electron back bombardment effect, which can cause the limited electron current and accelerated energy. In this research, we aim to develop the photocathode RF gun for the linac-based THz radiation source. Its design is based on the existing gun at the PBP-CMU Linac Laboratory. The gun consists of a one and a half cell S-band standing-wave RF cavities with a maximum electric field of about 60 MV/m at the centre of the full cell. We study the beam dynamics of electrons traveling through the electromagnetic field inside the RF gun by using the particle tracking program ASTRA. The laser properties i.e. transverse size and injecting phase are optimized to obtain low transverse emittance. In addition, the solenoid magnet is applied for beam focusing and emittance compensation. The proper solenoid magnetic field is then investigated to find the optimum value for proper emittance conservation condition.

Monaural Sound Localization Based on Reflective Structure and Homomorphic Deconvolution

PubMed Central

Park, Yeonseok; Choi, Anthony

2017-01-01

The asymmetric structure around the receiver provides a particular time delay for the specific incoming propagation. This paper designs a monaural sound localization system based on the reflective structure around the microphone. The reflective plates are placed to present the direction-wise time delay, which is naturally processed by convolutional operation with a sound source. The received signal is separated for estimating the dominant time delay by using homomorphic deconvolution, which utilizes the real cepstrum and inverse cepstrum sequentially to derive the propagation response’s autocorrelation. Once the localization system accurately estimates the information, the time delay model computes the corresponding reflection for localization. Because of the structure limitation, two stages of the localization process perform the estimation procedure as range and angle. The software toolchain from propagation physics and algorithm simulation realizes the optimal 3D-printed structure. The acoustic experiments in the anechoic chamber denote that 79.0% of the study range data from the isotropic signal is properly detected by the response value, and 87.5% of the specific direction data from the study range signal is properly estimated by the response time. The product of both rates shows the overall hit rate to be 69.1%. PMID:28946625

Study and Implementation of White Power-LED Based Indoor Lighting Application for the Healthcare Sector

NASA Astrophysics Data System (ADS)

Chakraborty, A.; Ganguly, R.

With the current technological growth in the field of device fabrication, white power-LED's are available for solid state lighting applications. This is a paradigm shift from electrical lighting to electronic lighting. The implemented systems are showing some promise by saving a considerable amount of energy as well as providing a good and acceptable illumination level. However, the `useful life' of such devices is an important parameter. If the proper device is not chosen, the desired reliability and performance will not be obtained. In the present work, different parameters associated with reliability of such LED's are studied. Four different varieties of LED's are put to test the `useful life' as per IESNA LM 79 standard. From the results obtained, the proper LED is chosen for further application. Subsequently, lighting design is done for a hospital waiting room (indoor application) with 24 × 7 lighting requirements for replacement of existing CFLs there. The calculations show that although the initial cost is higher for LED based lighting, yet the savings on energy and replacement of the lamp results in a payback time of less than a year.

BPELPower—A BPEL execution engine for geospatial web services

NASA Astrophysics Data System (ADS)

Yu, Genong (Eugene); Zhao, Peisheng; Di, Liping; Chen, Aijun; Deng, Meixia; Bai, Yuqi

2012-10-01

The Business Process Execution Language (BPEL) has become a popular choice for orchestrating and executing workflows in the Web environment. As one special kind of scientific workflow, geospatial Web processing workflows are data-intensive, deal with complex structures in data and geographic features, and execute automatically with limited human intervention. To enable the proper execution and coordination of geospatial workflows, a specially enhanced BPEL execution engine is required. BPELPower was designed, developed, and implemented as a generic BPEL execution engine with enhancements for executing geospatial workflows. The enhancements are especially in its capabilities in handling Geography Markup Language (GML) and standard geospatial Web services, such as the Web Processing Service (WPS) and the Web Feature Service (WFS). BPELPower has been used in several demonstrations over the decade. Two scenarios were discussed in detail to demonstrate the capabilities of BPELPower. That study showed a standard-compliant, Web-based approach for properly supporting geospatial processing, with the only enhancement at the implementation level. Pattern-based evaluation and performance improvement of the engine are discussed: BPELPower directly supports 22 workflow control patterns and 17 workflow data patterns. In the future, the engine will be enhanced with high performance parallel processing and broad Web paradigms.

Balancing Play, Meaning and Reality: The Design Philosophy of LEVEE PATROLLER

ERIC Educational Resources Information Center

Harteveld, Casper; Guimaraes, Rui; Mayer, Igor S.; Bidarra, Rafael

2010-01-01

Most serious games have been developed without a proper and comprehensive design theory. To contribute to the development of such a theory, this article presents the underlying design philosophy of LEVEE PATROLLER, a game to train levee patrollers in the Netherlands. This philosophy stipulates that the design of a digital serious game is a…

A novel coherent optical en/decoder for optical label processing of OCDM-based optical packets switching networks

NASA Astrophysics Data System (ADS)

Zhang, Chongfu; Qiu, Kun

2007-11-01

A coherent optical en/decoder based on photonic crystal (PhC) for optical code-division-multiple (OCDM)-based optical label (OCDM-OL) optical packets switching (OPS) networks is proposed in this paper. In this scheme, the optical pulse phase and time delay can be flexibly controlled by the photonic crystal phase shifter and delayer using the appropriate design of fabrication. In this design, the combination calculation of the impurity and normal period layers is applied, according to the PhC transmission matrix theorem. The design and theoretical analysis of the PhC-based optical coherent en/decoder is mainly focused. In addition, the performances of the PhC-based optical en/decoders are analyzed in detail. The reflection, the transmission, delay characteristic and the optical spectrum of pulse en/decoded are studied for the waves tuned in the photonic band-gap by the numerical calculation, taking into account 1-Dimension (1D) PhC. Theoretical analysis and numerical results show that optical pulse is achieved to properly phase modulation and time delay by the proposed scheme, optical label based on OCDM is rewrote successfully by new code for OCDM-based OPS (OCDM-OPS), and an over 8.5 dB ration of auto- and cross-correlation is gained, which demonstrates the applicability of true pulse phase modulation in a number of applications.

Transonic Flutter Suppression Control Law Design, Analysis and Wind Tunnel Results

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek

1999-01-01

The benchmark active controls technology and wind tunnel test program at NASA Langley Research Center was started with the objective to investigate the nonlinear, unsteady aerodynamics and active flutter suppression of wings in transonic flow. The paper will present the flutter suppression control law design process, numerical nonlinear simulation and wind tunnel test results for the NACA 0012 benchmark active control wing model. The flutter suppression control law design processes using (1) classical, (2) linear quadratic Gaussian (LQG), and (3) minimax techniques are described. A unified general formulation and solution for the LQG and minimax approaches, based on the steady state differential game theory is presented. Design considerations for improving the control law robustness and digital implementation are outlined. It was shown that simple control laws when properly designed based on physical principles, can suppress flutter with limited control power even in the presence of transonic shocks and flow separation. In wind tunnel tests in air and heavy gas medium, the closed-loop flutter dynamic pressure was increased to the tunnel upper limit of 200 psf The control law robustness and performance predictions were verified in highly nonlinear flow conditions, gain and phase perturbations, and spoiler deployment. A non-design plunge instability condition was also successfully suppressed.

Transonic Flutter Suppression Control Law Design, Analysis and Wind-Tunnel Results

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek

1999-01-01

The benchmark active controls technology and wind tunnel test program at NASA Langley Research Center was started with the objective to investigate the nonlinear, unsteady aerodynamics and active flutter suppression of wings in transonic flow. The paper will present the flutter suppression control law design process, numerical nonlinear simulation and wind tunnel test results for the NACA 0012 benchmark active control wing model. The flutter suppression control law design processes using (1) classical, (2) linear quadratic Gaussian (LQG), and (3) minimax techniques are described. A unified general formulation and solution for the LQG and minimax approaches, based on the steady state differential game theory is presented. Design considerations for improving the control law robustness and digital implementation are outlined. It was shown that simple control laws when properly designed based on physical principles, can suppress flutter with limited control power even in the presence of transonic shocks and flow separation. In wind tunnel tests in air and heavy gas medium, the closed-loop flutter dynamic pressure was increased to the tunnel upper limit of 200 psf. The control law robustness and performance predictions were verified in highly nonlinear flow conditions, gain and phase perturbations, and spoiler deployment. A non-design plunge instability condition was also successfully suppressed.

Transonic Flutter Suppression Control Law Design Using Classical and Optimal Techniques with Wind-Tunnel Results

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek

1999-01-01

The benchmark active controls technology and wind tunnel test program at NASA Langley Research Center was started with the objective to investigate the nonlinear, unsteady aerodynamics and active flutter suppression of wings in transonic flow. The paper will present the flutter suppression control law design process, numerical nonlinear simulation and wind tunnel test results for the NACA 0012 benchmark active control wing model. The flutter suppression control law design processes using (1) classical, (2) linear quadratic Gaussian (LQG), and (3) minimax techniques are described. A unified general formulation and solution for the LQG and minimax approaches, based on the steady state differential game theory is presented. Design considerations for improving the control law robustness and digital implementation are outlined. It was shown that simple control laws when properly designed based on physical principles, can suppress flutter with limited control power even in the presence of transonic shocks and flow separation. In wind tunnel tests in air and heavy gas medium, the closed-loop flutter dynamic pressure was increased to the tunnel upper limit of 200 psf. The control law robustness and performance predictions were verified in highly nonlinear flow conditions, gain and phase perturbations, and spoiler deployment. A non-design plunge instability condition was also successfully suppressed.

Overview of NASA Langley's Piezoelectric Ceramic Packaging Technology and Applications

NASA Technical Reports Server (NTRS)

Bryant, Robert G.

2007-01-01

Over the past decade, NASA Langley Research Center (LaRC) has developed several actuator packaging concepts designed to enhance the performance of commercial electroactive ceramics. NASA LaRC focused on properly designed actuator and sensor packaging for the following reasons, increased durability, protect the working material from the environment, allow for proper mechanical and electrical contact, afford "ready to use" mechanisms that are scalable, and develop fabrication methodology applicable to any active material of the same physical class. It is more cost effective to enhance or tailor the performance of existing systems, through innovative packaging, than to develop, test and manufacture new materials. This approach led to the development of several solid state actuators that include THUNDER, the Macrofiber Composite or (MFC) and the Radial Field Diaphragm or (RFD). All these actuators are fabricated using standard materials and processes derived from earlier concepts. NASA s fabrication and packaging technology as yielded, piezoelectric actuators and sensors that are easy to implement, reliable, consistent in properties, and of lower cost to manufacture in quantity, than their predecessors (as evidenced by their continued commercial availability.) These piezoelectric actuators have helped foster new research and development in areas involving computational modeling, actuator specific refinements, and engineering system redesign which led to new applications for piezo-based devices that replace traditional systems currently in use.

Design of helicopter rotor blades for optimum dynamic characteristics

NASA Technical Reports Server (NTRS)

Peters, D. A.; Ko, T.; Korn, A. E.; Rossow, M. P.

1982-01-01

The possibilities and the limitations of tailoring blade mass and stiffness distributions to give an optimum blade design in terms of weight, inertia, and dynamic characteristics are investigated. Changes in mass or stiffness distribution used to place rotor frequencies at desired locations are determined. Theoretical limits to the amount of frequency shift are established. Realistic constraints on blade properties based on weight, mass moment of inertia size, strength, and stability are formulated. The extent hub loads can be minimized by proper choice of EL distribution is determined. Configurations that are simple enough to yield clear, fundamental insights into the structural mechanisms but which are sufficiently complex to result in a realistic result for an optimum rotor blade are emphasized.

Instrumentation, control, and automation for submerged anaerobic membrane bioreactors.

PubMed

Robles, Ángel; Durán, Freddy; Ruano, María Victoria; Ribes, Josep; Rosado, Alfredo; Seco, Aurora; Ferrer, José

2015-01-01

A submerged anaerobic membrane bioreactor (AnMBR) demonstration plant with two commercial hollow-fibre ultrafiltration systems (PURON®, Koch Membrane Systems, PUR-PSH31) was designed and operated for urban wastewater treatment. An instrumentation, control, and automation (ICA) system was designed and implemented for proper process performance. Several single-input-single-output (SISO) feedback control loops based on conventional on-off and PID algorithms were implemented to control the following operating variables: flow-rates (influent, permeate, sludge recycling and wasting, and recycled biogas through both reactor and membrane tanks), sludge wasting volume, temperature, transmembrane pressure, and gas sparging. The proposed ICA for AnMBRs for urban wastewater treatment enables the optimization of this new technology to be achieved with a high level of process robustness towards disturbances.

[Design of medical equipment service management system].

PubMed

Jiang, Youhao; PengWen; Jiang, Ningfeng; Ma, Li; Kong, Lingwei; Yin, PeiHao; Sun, Cheng

2012-09-01

To develop a maintenance management system for medical equipment based on HIS. The system contains some special functions( including preventive maintenance, automatic job dispatch, performance assessment, etc.) which are very useful for confirming the medical equipment in proper conditions and promoting the working efficiency of the staff. The system provides technical support for the improvement of the maintenance management level. The system, completed the software design using C/S, B/S combination mode. The system realized clients of various sections of zero maintenance, and make the data manipulation, statistical features of equipment management department more convenient. the system connects the subsystems closer and interacts information from time to time, forming a tight network structure. This provides a basis for future hospital-wide information integration.

First Operation of the Abort Gap Monitor for LHC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lefevre, Thibaut; /CERN; Bart Pedersen, Stephane

2012-07-06

The Large Hadron Collider (LHC) beam-dump system relies on extraction kickers that need 3 microseconds to rise to their nominal field. Since particles transiting the kickers during the rise will not be dumped properly, the proton population in this interval must always remain below quench and damage limits. A specific monitor to measure the particle population of this gap has been designed based on the detection of synchrotron radiation using a gated photomultiplier. Since the quench and damage limits change with the beam energy, the acceptable population in the abort gap and the settings of the monitor must adapt accordingly.more » This paper presents the design of the monitor, the calibration procedure and the detector performance with beam.« less

Collaborative efforts are needed to ensure proper knowledge dissemination of telemedicine projects.

PubMed

Jakobsen, Neel Kolthoff; Jensen, Lena Sundby; Kayser, Lars

2014-09-01

Telemedicine is often seen as the solution to the challenge of providing health care for an increasing number of people with chronic conditions. Projects are often organised locally and based on the involvement of stakeholders with a wide range of backgrounds. It can be challenging to ensure that projects are based on previous experience and that they do not repeat previous studies. To better understand these challenges and current practice, we examined telemedicine projects funded in the 2008-2010 period to explore where, how and to what extent results from the projects were documented and disseminated. Public and private funds were contacted for information about telemedicine studies focusing on people residing in their homes. After an initial screening of titles and abstracts, 19 projects were identified. The managers of the projects were contacted and information about project results and dissemination were obtained. More than half of all projects were disseminated to professionals as well as to the public and used two-way communication. However, it was generally difficult to obtain an overview of the projects due to dynamic changes in names and scopes. We propose that the funding authorities require designs comprising proper evaluation models that will subsequently allow the investigators to publish their findings. Furthermore, a dissemination plan comprising both peers and other professions should be made mandatory. The investigators should ensure proper documentation and dissemination of changes both during and after the projects in order to ensure transparency, and national or international organisations should establish a database with relevant data fields. not relevant. not relevant.

Telemedicine for Developing Countries

PubMed Central

Combi, Carlo; Pozzani, Gabriele

2016-01-01

Summary Background Developing countries need telemedicine applications that help in many situations, when physicians are a small number with respect to the population, when specialized physicians are not available, when patients and physicians in rural villages need assistance in the delivery of health care. Moreover, the requirements of telemedicine applications for developing countries are somewhat more demanding than for developed countries. Indeed, further social, organizational, and technical aspects need to be considered for successful telemedicine applications in developing countries. Objective We consider all the major projects in telemedicine, devoted to developing countries, as described by the proper scientific literature. On the basis of such literature, we want to define a specific taxonomy that allows a proper classification and a fast overview of telemedicine projects in developing countries. Moreover, by considering both the literature and some recent direct experiences, we want to complete such overview by discussing some design issues to be taken into consideration when developing telemedicine software systems. Methods We considered and reviewed the major conferences and journals in depth, and looked for reports on the telemedicine projects. Results We provide the reader with a survey of the main projects and systems, from which we derived a taxonomy of features of telemedicine systems for developing countries. We also propose and discuss some classification criteria for design issues, based on the lessons learned in this research area. Conclusions We highlight some challenges and recommendations to be considered when designing a telemedicine system for developing countries. PMID:27803948

Guidelines for Developing Spacecraft Structural Requirements: A Thermal and Environmental Perspective

NASA Technical Reports Server (NTRS)

Holladay, Jon; Day, Greg; Gill, Larry

2004-01-01

Spacecraft are typically designed with a primary focus on weight in order to meet launch vehicle performance parameters. However, for pressurized and/or man-rated spacecraft, it is also necessary to have an understanding of the vehicle operating environments to properly size the pressure vessel. Proper sizing of the pressure vessel requires an understanding of the space vehicle's life cycle and compares the physical design optimization (weight and launch "cost") to downstream operational complexity and total life cycle cost. This paper will provide an overview of some major environmental design drivers and provide examples for calculating the optimal design pressure versus a selected set of design parameters related to thermal and environmental perspectives. In addition, this paper will provide a generic set of cracking pressures for both positive and negative pressure relief valves that encompasses worst case environmental effects for a variety of launch / landing sites. Finally, several examples are included to highlight pressure relief set points and vehicle weight impacts for a selected set of orbital missions.

Design study of toroidal traction CVT for electric vehicles

NASA Technical Reports Server (NTRS)

Raynard, A. E.; Kraus, J.; Bell, D. D.

1980-01-01

The development, evaluation, and optimization of a preliminary design concept for a continuously variable transmission (CVT) to couple the high-speed output shaft of an energy storage flywheel to the drive train of an electric vehicle is discussed. An existing computer simulation program was modified and used to compare the performance of five CVT design configurations. Based on this analysis, a dual-cavity full-toroidal drive with regenerative gearing is selected for the CVT design configuration. Three areas are identified that will require some technological development: the ratio control system, the traction fluid properities, and evaluation of the traction contact performance. Finally, the suitability of the selected CVT design concept for alternate electric and hybrid vehicle applications and alternate vehicle sizes and maximum output torques is determined. In all cases the toroidal traction drive design concept is applicable to the vehicle system. The regenerative gearing could be eliminated in the electric powered vehicle because of the reduced ratio range requirements. In other cases the CVT with regenerative gearing would meet the design requirements after appropriate adjustments in size and reduction gearing ratio.

Applications of Bayesian spectrum representation in acoustics

NASA Astrophysics Data System (ADS)

Botts, Jonathan M.

This dissertation utilizes a Bayesian inference framework to enhance the solution of inverse problems where the forward model maps to acoustic spectra. A Bayesian solution to filter design inverts a acoustic spectra to pole-zero locations of a discrete-time filter model. Spatial sound field analysis with a spherical microphone array is a data analysis problem that requires inversion of spatio-temporal spectra to directions of arrival. As with many inverse problems, a probabilistic analysis results in richer solutions than can be achieved with ad-hoc methods. In the filter design problem, the Bayesian inversion results in globally optimal coefficient estimates as well as an estimate the most concise filter capable of representing the given spectrum, within a single framework. This approach is demonstrated on synthetic spectra, head-related transfer function spectra, and measured acoustic reflection spectra. The Bayesian model-based analysis of spatial room impulse responses is presented as an analogous problem with equally rich solution. The model selection mechanism provides an estimate of the number of arrivals, which is necessary to properly infer the directions of simultaneous arrivals. Although, spectrum inversion problems are fairly ubiquitous, the scope of this dissertation has been limited to these two and derivative problems. The Bayesian approach to filter design is demonstrated on an artificial spectrum to illustrate the model comparison mechanism and then on measured head-related transfer functions to show the potential range of application. Coupled with sampling methods, the Bayesian approach is shown to outperform least-squares filter design methods commonly used in commercial software, confirming the need for a global search of the parameter space. The resulting designs are shown to be comparable to those that result from global optimization methods, but the Bayesian approach has the added advantage of a filter length estimate within the same unified framework. The application to reflection data is useful for representing frequency-dependent impedance boundaries in finite difference acoustic simulations. Furthermore, since the filter transfer function is a parametric model, it can be modified to incorporate arbitrary frequency weighting and account for the band-limited nature of measured reflection spectra. Finally, the model is modified to compensate for dispersive error in the finite difference simulation, from the filter design process. Stemming from the filter boundary problem, the implementation of pressure sources in finite difference simulation is addressed in order to assure that schemes properly converge. A class of parameterized source functions is proposed and shown to offer straightforward control of residual error in the simulation. Guided by the notion that the solution to be approximated affects the approximation error, sources are designed which reduce residual dispersive error to the size of round-off errors. The early part of a room impulse response can be characterized by a series of isolated plane waves. Measured with an array of microphones, plane waves map to a directional response of the array or spatial intensity map. Probabilistic inversion of this response results in estimates of the number and directions of image source arrivals. The model-based inversion is shown to avoid ambiguities associated with peak-finding or inspection of the spatial intensity map. For this problem, determining the number of arrivals in a given frame is critical for properly inferring the state of the sound field. This analysis is effectively compression of the spatial room response, which is useful for analysis or encoding of the spatial sound field. Parametric, model-based formulations of these problems enhance the solution in all cases, and a Bayesian interpretation provides a principled approach to model comparison and parameter estimation. v

Development of Boundary Condition Independent Reduced Order Thermal Models using Proper Orthogonal Decomposition

NASA Astrophysics Data System (ADS)

Raghupathy, Arun; Ghia, Karman; Ghia, Urmila

2008-11-01

Compact Thermal Models (CTM) to represent IC packages has been traditionally developed using the DELPHI-based (DEvelopment of Libraries of PHysical models for an Integrated design) methodology. The drawbacks of this method are presented, and an alternative method is proposed. A reduced-order model that provides the complete thermal information accurately with less computational resources can be effectively used in system level simulations. Proper Orthogonal Decomposition (POD), a statistical method, can be used to reduce the order of the degree of freedom or variables of the computations for such a problem. POD along with the Galerkin projection allows us to create reduced-order models that reproduce the characteristics of the system with a considerable reduction in computational resources while maintaining a high level of accuracy. The goal of this work is to show that this method can be applied to obtain a boundary condition independent reduced-order thermal model for complex components. The methodology is applied to the 1D transient heat equation.

Attitude Heading Reference System Using MEMS Inertial Sensors with Dual-Axis Rotation

PubMed Central

Kang, Li; Ye, Lingyun; Song, Kaichen; Zhou, Yang

2014-01-01

This paper proposes a low cost and small size attitude and heading reference system based on MEMS inertial sensors. A dual-axis rotation structure with a proper rotary scheme according to the design principles is applied in the system to compensate for the attitude and heading drift caused by the large gyroscope biases. An optimization algorithm is applied to compensate for the installation angle error between the body frame and the rotation table's frame. Simulations and experiments are carried out to evaluate the performance of the AHRS. The results show that the proper rotation could significantly reduce the attitude and heading drifts. Moreover, the new AHRS is not affected by magnetic interference. After the rotation, the attitude and heading are almost just oscillating in a range. The attitude error is about 3° and the heading error is less than 3° which are at least 5 times better than the non-rotation condition. PMID:25268911

Years to first rehabilitation of superpave hot mix asphalt.

DOT National Transportation Integrated Search

2014-07-01

The Colorado Department of Transportation (CDOT) spends more than 30 percent of its annual construction and : maintenance budget on pavements, so pavements need to be properly designed using an analytical process with : accurate design inputs. A pave...

VizieR Online Data Catalog: Proper motions of PM2000 open clusters (Krone-Martins+, 2010)

NASA Astrophysics Data System (ADS)

Krone-Martins, A.; Soubiran, C.; Ducourant, C.; Teixeira, R.; Le Campion, J. F.

2010-04-01

We present lists of proper-motions and kinematic membership probabilities in the region of 49 open clusters or possible open clusters. The stellar proper motions were taken from the Bordeaux PM2000 catalogue. The segregation between cluster and field stars and the assignment of membership probabilities was accomplished by applying a fully automated method based on parametrisations for the probability distribution functions and genetic algorithm optimisation heuristics associated with a derivative-based hill climbing algorithm for the likelihood optimization. (3 data files).

Building a biomedical tokenizer using the token lattice design pattern and the adapted Viterbi algorithm

PubMed Central

2011-01-01

Background Tokenization is an important component of language processing yet there is no widely accepted tokenization method for English texts, including biomedical texts. Other than rule based techniques, tokenization in the biomedical domain has been regarded as a classification task. Biomedical classifier-based tokenizers either split or join textual objects through classification to form tokens. The idiosyncratic nature of each biomedical tokenizer’s output complicates adoption and reuse. Furthermore, biomedical tokenizers generally lack guidance on how to apply an existing tokenizer to a new domain (subdomain). We identify and complete a novel tokenizer design pattern and suggest a systematic approach to tokenizer creation. We implement a tokenizer based on our design pattern that combines regular expressions and machine learning. Our machine learning approach differs from the previous split-join classification approaches. We evaluate our approach against three other tokenizers on the task of tokenizing biomedical text. Results Medpost and our adapted Viterbi tokenizer performed best with a 92.9% and 92.4% accuracy respectively. Conclusions Our evaluation of our design pattern and guidelines supports our claim that the design pattern and guidelines are a viable approach to tokenizer construction (producing tokenizers matching leading custom-built tokenizers in a particular domain). Our evaluation also demonstrates that ambiguous tokenizations can be disambiguated through POS tagging. In doing so, POS tag sequences and training data have a significant impact on proper text tokenization. PMID:21658288

Manual centrifuge system: Bearing-based hand spinner made with 3-D printer.

PubMed

Sun-Young Yoo; Seung Jae Lee; Jong-Mo Seo

2017-07-01

Compact disk (CD) Microfluidic platforms are being studied for medical applications such as blood tests. However, its size is bulky and electricity is needed to realize centrifuge force. In this paper, bearing-based hand spinner is designed using three-dimensional printer. This spinner does not need electricity and keeps rotating direction unlike paperfuge while it is spinning. The properties of spinner vary depending on bearing type which is positioned at the center. The type of weighting area also affects change in RPM over time. When a separation experiment is implemented, separating mixture into red ink and oil and whole blood into red blood cell and plasma are achieved properly with ceramic ball bearing.

Business process analysis of a foodborne outbreak investigation mobile system

NASA Astrophysics Data System (ADS)

Nowicki, T.; Waszkowski, R.; Saniuk, A.

2016-08-01

Epidemiological investigation during an outbreak of food-borne disease requires taking a number of activities carried out in the field. This results in a restriction of access to current data about the epidemic and reducing the possibility of transferring information from the field to headquarters. This problem can be solved by using an appropriate system of mobile devices. The purpose of this paper is to present the IT solution based on the central repository for epidemiological investigations and mobile devices designed for use in the field. Based on such a solution business processes can be properly rebuild in a way to achieve better results in the activities of health inspectors.

Prediction-based association control scheme in dense femtocell networks

PubMed Central

Pham, Ngoc-Thai; Huynh, Thong; Hwang, Won-Joo; You, Ilsun; Choo, Kim-Kwang Raymond

2017-01-01

The deployment of large number of femtocell base stations allows us to extend the coverage and efficiently utilize resources in a low cost manner. However, the small cell size of femtocell networks can result in frequent handovers to the mobile user, and consequently throughput degradation. Thus, in this paper, we propose predictive association control schemes to improve the system’s effective throughput. Our design focuses on reducing handover frequency without impacting on throughput. The proposed schemes determine handover decisions that contribute most to the network throughput and are proper for distributed implementations. The simulation results show significant gains compared with existing methods in terms of handover frequency and network throughput perspective. PMID:28328992

Tunable plasmon-induced transparency effect based on self-asymmetric H-shaped resonators meta-atoms

NASA Astrophysics Data System (ADS)

Cheng, Zhaoxiang; Chen, Lin; Zang, Xiaofei; Cai, Bin; Peng, Yan; Zhu, Yiming

2015-03-01

We have proposed and demonstrated a tunable plasmon-induced transparency (PIT) effect from two ways, based on self-asymmetric H-shaped resonators (AHR) meta-atoms. The tunable PIT effect is realized via varying polarization angles and coupling distances. First, by proper design, transition from PIT mode to dipole mode is theoretically and experimentally demonstrated by simply adjusting the polarization angle. Also, the manipulation of ‘dark-mode’ resonance intensity from strong to weak is achieved by varying coupling strength with different distances, which provided insight into the magnetic coupling hybridization mechanism. Prospectively, due to its special tunable characteristics, the AHR meta-atoms may be widely used in slow light, filters and switch devices.

Beam-splitter switches based on zenithal bistable liquid-crystal gratings.

PubMed

Zografopoulos, Dimitrios C; Beccherelli, Romeo; Kriezis, Emmanouil E

2014-10-01

The tunable optical diffractive properties of zenithal bistable nematic liquid-crystal gratings are theoretically investigated. The liquid-crystal orientation is rigorously solved via a tensorial formulation of the Landau-de Gennes theory and the optical transmission properties of the gratings are investigated via full-wave finite-element frequency-domain simulations. It is demonstrated that by proper design the two stable states of the grating can provide nondiffracting and diffracting operation, the latter with equal power splitting among different diffraction orders. An electro-optic switching mechanism, based on dual-frequency nematic materials, and its temporal dynamics are further discussed. Such gratings provide a solution towards tunable beam-steering and beam-splitting components with extremely low power consumption.

Principles and performance of tapered fiber lasers: from uniform to flared geometry.

PubMed

Kerttula, Juho; Filippov, Valery; Chamorovskii, Yuri; Ustimchik, Vasily; Golant, Konstantin; Okhotnikov, Oleg G

2012-10-10

We have studied the recently demonstrated concept of fiber lasers based on active tapered double-clad fiber (T-DCF) in copropagating and counterpropagating configurations, both theoretically and experimentally, and compared the performance to fiber lasers based on conventional cylindrical fibers in end-pumped configurations. Specific properties of T-DCFs were considered theoretically using a rate-equation model developed for tapered fibers, and a detailed comparative study was carried out experimentally. Furthermore, we have studied mode coupling effects in long adiabatic tapers due to coiling and local bending. The results allow us to conclude that, with proper fiber design, the T-DCF technology offers a high-potential alternative for bright, cost-effective fiber devices.

Design of a video teleconference facility for a synchronous satellite communications link

NASA Technical Reports Server (NTRS)

Richardson, M. D.

1979-01-01

The system requirements, design tradeoffs, and final design of a video teleconference facility are discussed, including proper lighting, graphics transmission, and picture aesthetics. Methods currently accepted in the television broadcast industry are used in the design. The unique problems associated with using an audio channel with a synchronous satellite communications link are discussed, and a final audio system design is presented.

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

Collection of materials and performance data for Texas flexible pavements and overlays : project summary.

DOT National Transportation Integrated Search

2015-08-31

Proper calibration of mechanistic-empirical : (M-E) design and rehabilitation performance : models to meet Texas conditions is essential : for cost-effective flexible pavement designs. : Such a calibration effort would require a : reliable source of ...

46 CFR 61.35-1 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PERIODIC TESTS AND INSPECTIONS Design Verification and Periodic Testing for Automatic Auxiliary Boilers § 61.35-1 General. (a) All automatic... equipment must be tested and inspected to verify their proper design, construction, installation, and...

Designing Birefringent Filters For Solid-State Lasers

NASA Technical Reports Server (NTRS)

Monosmith, Bryan

1992-01-01

Mathematical model enables design of filter assembly of birefringent plates as integral part of resonator cavity of tunable solid-state laser. Proper design treats polarization eigenstate of entire resonator as function of wavelength. Program includes software modules for variety of optical elements including Pockels cell, laser rod, quarter- and half-wave plates, Faraday rotator, and polarizers.

Statistical Analysis for the Solomon Four-Group Design. Research Report 99-06.

ERIC Educational Resources Information Center

van Engelenburg, Gijsbert

The Solomon four-group design (R. Solomon, 1949) is a very useful experimental design to investigate the main effect of a pretest and the interaction of pretest and treatment. Although the design was proposed half a century ago, no proper data analysis techniques have been available. This paper describes how data from the Solomon four-group design…

Inter-Creative Course Model Proposal: Teaching- Learning Design in Secondary Schools of TRNC

ERIC Educational Resources Information Center

Ulas-Dagli, Ugur; Pasaoglulari-Sahin, Nil; Güley, Kamil

2013-01-01

Problem Statement: Design is an indispensable part of the human being. It enters one's life on the very first day that the eyes open. Design awareness is developed at an early age. With a proper education, even in the preschool years, design is experienced within one's close environment. Purpose of the Study: This study aims to determine the…

Development of Innovative Design Processor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Y.S.; Park, C.O.

2004-07-01

The nuclear design analysis requires time-consuming and erroneous model-input preparation, code run, output analysis and quality assurance process. To reduce human effort and improve design quality and productivity, Innovative Design Processor (IDP) is being developed. Two basic principles of IDP are the document-oriented design and the web-based design. The document-oriented design is that, if the designer writes a design document called active document and feeds it to a special program, the final document with complete analysis, table and plots is made automatically. The active documents can be written with ordinary HTML editors or created automatically on the web, which ismore » another framework of IDP. Using the proper mix-up of server side and client side programming under the LAMP (Linux/Apache/MySQL/PHP) environment, the design process on the web is modeled as a design wizard style so that even a novice designer makes the design document easily. This automation using the IDP is now being implemented for all the reload design of Korea Standard Nuclear Power Plant (KSNP) type PWRs. The introduction of this process will allow large reduction in all reload design efforts of KSNP and provide a platform for design and R and D tasks of KNFC. (authors)« less

In silico fragment-based drug design.

PubMed

Konteatis, Zenon D

2010-11-01

In silico fragment-based drug design (FBDD) is a relatively new approach inspired by the success of the biophysical fragment-based drug discovery field. Here, we review the progress made by this approach in the last decade and showcase how it complements and expands the capabilities of biophysical FBDD and structure-based drug design to generate diverse, efficient drug candidates. Advancements in several areas of research that have enabled the development of in silico FBDD and some applications in drug discovery projects are reviewed. The reader is introduced to various computational methods that are used for in silico FBDD, the fragment library composition for this technique, special applications used to identify binding sites on the surface of proteins and how to assess the druggability of these sites. In addition, the reader will gain insight into the proper application of this approach from examples of successful programs. In silico FBDD captures a much larger chemical space than high-throughput screening and biophysical FBDD increasing the probability of developing more diverse, patentable and efficient molecules that can become oral drugs. The application of in silico FBDD holds great promise for historically challenging targets such as protein-protein interactions. Future advances in force fields, scoring functions and automated methods for determining synthetic accessibility will all aid in delivering more successes with in silico FBDD.

Sensitivity analysis and approximation methods for general eigenvalue problems

NASA Technical Reports Server (NTRS)

Murthy, D. V.; Haftka, R. T.

1986-01-01

Optimization of dynamic systems involving complex non-hermitian matrices is often computationally expensive. Major contributors to the computational expense are the sensitivity analysis and reanalysis of a modified design. The present work seeks to alleviate this computational burden by identifying efficient sensitivity analysis and approximate reanalysis methods. For the algebraic eigenvalue problem involving non-hermitian matrices, algorithms for sensitivity analysis and approximate reanalysis are classified, compared and evaluated for efficiency and accuracy. Proper eigenvector normalization is discussed. An improved method for calculating derivatives of eigenvectors is proposed based on a more rational normalization condition and taking advantage of matrix sparsity. Important numerical aspects of this method are also discussed. To alleviate the problem of reanalysis, various approximation methods for eigenvalues are proposed and evaluated. Linear and quadratic approximations are based directly on the Taylor series. Several approximation methods are developed based on the generalized Rayleigh quotient for the eigenvalue problem. Approximation methods based on trace theorem give high accuracy without needing any derivatives. Operation counts for the computation of the approximations are given. General recommendations are made for the selection of appropriate approximation technique as a function of the matrix size, number of design variables, number of eigenvalues of interest and the number of design points at which approximation is sought.

Design of embedded system to determine liquid refractive index based on ultrasonic sensor using an ATMega328

NASA Astrophysics Data System (ADS)

Radiyonoa, Y.; Surantoro, S.; Pujayanto, P.; Budiharti, R.; Respati, Y. S.; Saputro, D. E.

2018-05-01

The occurrence of the broken pencil shadow into a glass of water becomes an interesting matter to be learned. The students of senior high school still find difficulty in determining liquid refractive index. To overcome this problem, it needs to develop an experimental tool to determine liquid refractive index by utilizing the newest technology. It is expected to be useful for students. This study is aimed to (1) make the design of physics learning experimental tool determinant of a liquid refractive index assisted by microcontroller based on ultrasonic sensors ATMega328 (2) explain the working principle and experimental result of liquid refractive indexing instrument assisted with ATMega328 microcontroller based ultrasonic sensor. This research used the experimental method. The result of the research shows design of physics learning experimental tool determinant of a liquid refractive index assisted by microcontroller based on ultrasonic sensors ATMega328 that has relative counting mistake of 0.36% on the measurement of aquades liquid refractive index, relative mistake of 0.18% on the 5% NaCl measurement, 0.24% on 5% glucose, and relative mistake of 0.50% on the measurement of 5 % fructose liquid refractive index. It has been created a proper device to be used in determining liquid refractive index.

Quantitative thermodynamic predication of interactions between nucleic acid and non-nucleic acid species using Microsoft excel.

PubMed

Zou, Jiaqi; Li, Na

2013-09-01

Proper design of nucleic acid sequences is crucial for many applications. We have previously established a thermodynamics-based quantitative model to help design aptamer-based nucleic acid probes by predicting equilibrium concentrations of all interacting species. To facilitate customization of this thermodynamic model for different applications, here we present a generic and easy-to-use platform to implement the algorithm of the model with Microsoft(®) Excel formulas and VBA (Visual Basic for Applications) macros. Two Excel spreadsheets have been developed: one for the applications involving only nucleic acid species, the other for the applications involving both nucleic acid and non-nucleic acid species. The spreadsheets take the nucleic acid sequences and the initial concentrations of all species as input, guide the user to retrieve the necessary thermodynamic constants, and finally calculate equilibrium concentrations for all species in various bound and unbound conformations. The validity of both spreadsheets has been verified by comparing the modeling results with the experimental results on nucleic acid sequences reported in the literature. This Excel-based platform described here will allow biomedical researchers to rationalize the sequence design of nucleic acid probes using the thermodynamics-based modeling even without relevant theoretical and computational skills. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Simulated Annealing-based Optimal Proportional-Integral-Derivative (PID) Controller Design: A Case Study on Nonlinear Quadcopter Dynamics

NASA Astrophysics Data System (ADS)

Nemirsky, Kristofer Kevin

In this thesis, the history and evolution of rotor aircraft with simulated annealing-based PID application were reviewed and quadcopter dynamics are presented. The dynamics of a quadcopter were then modeled, analyzed, and linearized. A cascaded loop architecture with PID controllers was used to stabilize the plant dynamics, which was improved upon through the application of simulated annealing (SA). A Simulink model was developed to test the controllers and verify the functionality of the proposed control system design. In addition, the data that the Simulink model provided were compared with flight data to present the validity of derived dynamics as a proper mathematical model representing the true dynamics of the quadcopter system. Then, the SA-based global optimization procedure was applied to obtain optimized PID parameters. It was observed that the tuned gains through the SA algorithm produced a better performing PID controller than the original manually tuned one. Next, we investigated the uncertain dynamics of the quadcopter setup. After adding uncertainty to the gyroscopic effects associated with pitch-and-roll rate dynamics, the controllers were shown to be robust against the added uncertainty. A discussion follows to summarize SA-based algorithm PID controller design and performance outcomes. Lastly, future work on SA application on multi-input-multi-output (MIMO) systems is briefly discussed.

High-field neutral beam injection for improving the Q of a gas dynamic trap-based fusion neutron source

NASA Astrophysics Data System (ADS)

Zeng, Qiusun; Chen, Dehong; Wang, Minghuang

2017-12-01

In order to improve the fusion energy gain (Q) of a gas dynamic trap (GDT)-based fusion neutron source, a method in which the neutral beam is obliquely injected at a higher magnetic field position rather than at the mid-plane of the GDT is proposed. This method is beneficial for confining a higher density of fast ions at the turning point in the zone with a higher magnetic field, as well as obtaining a higher mirror ratio by reducing the mid-plane field rather than increasing the mirror field. In this situation, collision scattering loss of fast ions with higher density will occur and change the confinement time, power balance and particle balance. Using an updated calculation model with high-field neutral beam injection for a GDT-based fusion neutron source conceptual design, we got four optimal design schemes for a GDT-based fusion neutron source in which Q was improved to two- to three-fold compared with a conventional design scheme and considering the limitation for avoiding plasma instabilities, especially the fire-hose instability. The distribution of fast ions could be optimized by building a proper magnetic field configuration with enough space for neutron shielding and by multi-beam neutral particle injection at different axial points.

A framework for the development of patient safety education and training guidelines.

PubMed

Zikos, Dimitrios; Diomidous, Marianna; Mantas, John

2010-01-01

Patient Safety (PS) is a major concern that involves a wide range of roles in healthcare, including those who are directly and indirectly involved, and patients as well. In order to succeed into developing a safety culture among healthcare providers, carers and patients, there should be given great attention into building appropriate education and training tools, especially addressing those who plan patient safety activities. The framework described in this policy paper is based on the results of the European Network for Patient Safety (EUNetPaS) project and analyses the principles and elements of the guidance that should be provided to those who design and implement Patient Safety Education and training activities. The main principles that it should be based on and the core teaching objectives-expected outcomes are addressed. Once the main context and considerations are properly set, the guidance should define the general schema of the content that should be included in the Education and Training activities, as well as how these activities would be delivered. It is also important that the different roles of the recipients are clearly distinguished and linked to their role-specific methods, proper delivery platforms and success stories. Setting these principles into practice when planning and implementing interventions, primarily aims to enlighten and support those who are enrolled to design and implement Patient Safety education and training teaching activities. This is achieved by providing them with a framework to build upon, succeeding to build a collaborative, safety conscious and competent environment, in terms of PS. A guidelines web platform has been developed to support this process.

An evaluation on the design of beam shaping assembly based on the D-T reaction for BNCT

NASA Astrophysics Data System (ADS)

Asnal, M.; Liamsuwan, T.; Onjun, T.

2015-05-01

Boron Neutron Capture Therapy (BNCT) can be achieved by using a compact neutron generator such as a compact D-T neutron source, in which neutron energy must be in the epithermal energy range with sufficient flux. For these requirements, a Beam Shaping Assembly (BSA) is needed. In this paper, three BSA designs based on the D-T reaction for BNCT are discussed. It is found that the BSA configuration designed by Rasouli et al. satisfies all of the International Atomic Energy Agency (IAEA) criteria. It consists of 14 cm uranium as multiplier, 23 cm TiF3 and 36 cm Fluental as moderator, 4 cm Fe as fast neutron filter, 1 mm Li as thermal neutron filter, 2.6 cm Bi as gamma ray filter, and Pb as collimator and reflector. It is also found that use of specific filters is important for removing the fast and thermal neutrons and gamma contamination. Moreover, an appropriate neutron source plays a key role in providing a proper epithermal flux.

Discussions on attitude determination and control system for micro/nano/pico-satellites considering survivability based on Hodoyoshi-3 and 4 experiences

NASA Astrophysics Data System (ADS)

Nakasuka, Shinichi; Miyata, Kikuko; Tsuruda, Yoshihiro; Aoyanagi, Yoshihide; Matsumoto, Takeshi

2018-04-01

The recent advancement of micro/nano/pico-satellites technologies encourages many universities to develop three axis stabilized satellites. As three axis stabilization is high level technology requiring the proper functioning of various sensors, actuators and control software, many early satellites failed in their initial operation phase because of shortage of solar power generation or inability to realize the initial step of missions because of unexpected attitude control system performance. These results come from failure to design the satellite attitude determination and control system (ADCS) appropriately and not considering "satellite survivability." ADCS should be designed such that even if some sensors or actuators cannot work as expected, the satellite can survive and carry out some of its missions, even if not full. This paper discusses how to realize ADCS while taking satellite survivability into account, based on our experiences of design and in-orbit operations of Hodoyoshi-3 and 4 satellites launched in 2014, which suffered from various component anomalies but could complete their missions.

The Optical Gravitational Lensing Experiment. The Catalog of Stellar Proper Motions toward the Magellanic Clouds

NASA Astrophysics Data System (ADS)

Poleski, R.; Soszyński, I.; Udalski, A.; Szymański, M. K.; Kubiak, M.; Pietrzyński, G.; Wyrzykowski, Ł.; Ulaczyk, K.

2012-03-01

We present a catalog of over 6.2 million stars with measured proper motions. All these stars are observed in the direction of the Magellanic Clouds within the brightness range 12

E-ELT requirements management

NASA Astrophysics Data System (ADS)

Schneller, D.

2014-08-01

The E-ELT has completed its design phase and is now entering construction. ESO is acting as prime contractor and usually procures subsystems, including their design, from industry. This, in turn, leads to a large number of requirements, whose validity, consistency and conformity with user needs requires extensive management. Therefore E-ELT Systems Engineering has chosen to follow a systematic approach, based on a reasoned requirement architecture that follows the product breakdown structure of the observatory. The challenge ahead is the controlled flow-down of science user needs into engineering requirements, requirement specifications and system design documents. This paper shows how the E-ELT project manages this. The project has adopted IBM DOORTM as a supporting requirements management tool. This paper deals with emerging problems and pictures potential solutions. It shows trade-offs made to reach a proper balance between the effort put in this activity and potential overheads, and the benefit for the project.

Which Tibial Tray Design Achieves Maximum Coverage and Ideal Rotation: Anatomic, Symmetric, or Asymmetric? An MRI-based study.

PubMed

Stulberg, S David; Goyal, Nitin

2015-10-01

Two goals of tibial tray placement in TKA are to maximize coverage and establish proper rotation. Our purpose was to utilize MRI information obtained as part of PSI planning to determine the impact of tibial tray design on the relationship between coverage and rotation. MR images for 100 consecutive knees were uploaded into PSI software. Preoperative planning software was used to evaluate 3 different tray designs: anatomic, symmetric, and asymmetric. Approximately equally good coverage was achieved with all three trays. However, the anatomic compared to symmetric/asymmetric trays required less malrotation (0.3° vs 3.0/2.4°; P < 0.001), with a higher proportion of cases within 5° of neutral (97% vs 73/77%; P < 0.001). In this study, the anatomic tibia optimized the relationship between coverage and rotation. Copyright © 2015 Elsevier Inc. All rights reserved.

Designing Class Methods from Dataflow Diagrams

NASA Astrophysics Data System (ADS)

Shoval, Peretz; Kabeli-Shani, Judith

A method for designing the class methods of an information system is described. The method is part of FOOM - Functional and Object-Oriented Methodology. In the analysis phase of FOOM, two models defining the users' requirements are created: a conceptual data model - an initial class diagram; and a functional model - hierarchical OO-DFDs (object-oriented dataflow diagrams). Based on these models, a well-defined process of methods design is applied. First, the OO-DFDs are converted into transactions, i.e., system processes that supports user task. The components and the process logic of each transaction are described in detail, using pseudocode. Then, each transaction is decomposed, according to well-defined rules, into class methods of various types: basic methods, application-specific methods and main transaction (control) methods. Each method is attached to a proper class; messages between methods express the process logic of each transaction. The methods are defined using pseudocode or message charts.

A compact semiconductor digital interferometer and its applications

NASA Astrophysics Data System (ADS)

Britsky, Oleksander I.; Gorbov, Ivan V.; Petrov, Viacheslav V.; Balagura, Iryna V.

2015-05-01

The possibility of using semiconductor laser interferometers to measure displacements at the nanometer scale was demonstrated. The creation principles of miniature digital Michelson interferometers based on semiconductor lasers were proposed. The advanced processing algorithm for the interferometer quadrature signals was designed. It enabled to reduce restrictions on speed of measured movements. A miniature semiconductor digital Michelson interferometer was developed. Designing of the precision temperature stability system for miniature low-cost semiconductor laser with 0.01ºС accuracy enabled to use it for creation of compact interferometer rather than a helium-neon one. Proper firmware and software was designed for the interferometer signals real-time processing and conversion in to respective shifts. In the result the relative displacement between 0-500 mm was measured with a resolution of better than 1 nm. Advantages and disadvantages of practical use of the compact semiconductor digital interferometer in seismometers for the measurement of shifts were shown.

Design Considerations of a Compounded Sterile Preparations Course

PubMed Central

Petraglia, Christine; Mattison, Melissa J.

2016-01-01

Objective. To design a comprehensive learning and assessment environment for the practical application of compounded sterile preparations using a constructivist approach. Design. Compounded Sterile Preparations Laboratory is a required 1-credit course that builds upon the themes of training aseptic technique typically used in health system settings and threads application of concepts from other courses in the curriculum. Students used critical-thinking skills to devise appropriate strategies to compound sterile preparations. Assessment. Aseptic technique skills were assessed with objective, structured, checklist-based rubrics. Most students successfully completed practical assessments using appropriate technique (mean assessment grade=83.2%). Almost all students passed the practical media fill (98%) and gloved fingertip sampling (86%) tests on the first attempt; all passed on the second attempt. Conclusion. Employing a constructivist scaffold approach to teaching proper hygiene and aseptic technique prepared students to pass media fill and gloved fingertip tests and to perform well on practical compounding assessments. PMID:26941438

Robust Design of Sheet Metal Forming Process Based on Kriging Metamodel

NASA Astrophysics Data System (ADS)

Xie, Yanmin

2011-08-01

Nowadays, sheet metal forming processes design is not a trivial task due to the complex issues to be taken into account (conflicting design goals, complex shapes forming and so on). Optimization methods have also been widely applied in sheet metal forming. Therefore, proper design methods to reduce time and costs have to be developed mostly based on computer aided procedures. At the same time, the existence of variations during manufacturing processes significantly may influence final product quality, rendering non-robust optimal solutions. In this paper, a small size of design of experiments is conducted to investigate how a stochastic behavior of noise factors affects drawing quality. The finite element software (LS_DYNA) is used to simulate the complex sheet metal stamping processes. The Kriging metamodel is adopted to map the relation between input process parameters and part quality. Robust design models for sheet metal forming process integrate adaptive importance sampling with Kriging model, in order to minimize impact of the variations and achieve reliable process parameters. In the adaptive sample, an improved criterion is used to provide direction in which additional training samples can be added to better the Kriging model. Nonlinear functions as test functions and a square stamping example (NUMISHEET'93) are employed to verify the proposed method. Final results indicate application feasibility of the aforesaid method proposed for multi-response robust design.

Design of an MR image processing module on an FPGA chip.

PubMed

Li, Limin; Wyrwicz, Alice M

2015-06-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128×128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments. Copyright © 2015 Elsevier Inc. All rights reserved.

Design and test of a prototype thermal bus evaporator reservoir aboard the KC-135 0-g aircraft

NASA Technical Reports Server (NTRS)

Brown, Richard F.; Gustafson, Eric; Long, W. Russ

1987-01-01

The Thermal Bus Zero-G Reservoir Demonstration Experiment (RDE) has currently undergone two flights on the NASA-JSC KC-135 Reduced Gravity Aircraft. The objective of the experiment, which uses a smaller version of the evaporator reservoirs being designed for the Prototype Thermal Bus for Space Station, is to demonstrate proper 0-g operation of the reservoir in terms of fluid positioning, draining, and filling. The KC-135 was chosen to provide a cost-effective and timely evaluation of 0-g design issues that would be difficult to predict analytically. A total of fifty 0-g parabolas have been flown, each providing approximately 25-30 seconds of 0-g time. While problems have been encountered, the experiment has provided valuable design data on the 0-g operation of the reservoir. This paper documents the design of the experiment; the results of both flights, based on the high-speed movies taken during the flight and the visual observations of the experimenters; and the design modifications made as a result of the first flight and planned as a result of the second flight.

On the aero-elastic design of the DTU 10MW wind turbine blade for the LIFES50+ wind tunnel scale model

NASA Astrophysics Data System (ADS)

Bayati, I.; Belloli, M.; Bernini, L.; Mikkelsen, R.; Zasso, A.

2016-09-01

This paper illustrates the aero-elastic optimal design, the realization and the verification of the wind tunnel scale model blades for the DTU 10 MW wind turbine model, within LIFES50+ project. The aerodynamic design was focused on the minimization of the difference, in terms of thrust coefficient, with respect to the full scale reference. From the Selig low Reynolds database airfoils, the SD7032 was chosen for this purpose and a proper constant section wing was tested at DTU red wind tunnel, providing force and distributed pressure coefficients for the design, in the Reynolds range 30-250 E3 and for different angles of attack. The aero-elastic design algorithm was set to define the optimal spanwise thickness over chord ratio (t/c), the chord length and the twist to match the first flapwise scaled natural frequency. An aluminium mould for the carbon fibre was CNC manufactured based on B-Splines CAD definition of the external geometry. Then the wind tunnel tests at Politecnico di Milano confirmed successful design and manufacturing approaches.

Optimal design of a bank of spatio-temporal filters for EEG signal classification.

PubMed

Higashi, Hiroshi; Tanaka, Toshihisa

2011-01-01

The spatial weights for electrodes called common spatial pattern (CSP) are known to be effective in EEG signal classification for motor imagery based brain computer interfaces (MI-BCI). To achieve accurate classification in CSP, the frequency filter should be properly designed. To this end, several methods for designing the filter have been proposed. However, the existing methods cannot consider plural brain activities described with different frequency bands and different spatial patterns such as activities of mu and beta rhythms. In order to efficiently extract these brain activities, we propose a method to design plural filters and spatial weights which extract desired brain activity. The proposed method designs finite impulse response (FIR) filters and the associated spatial weights by optimization of an objective function which is a natural extension of CSP. Moreover, we show by a classification experiment that the bank of FIR filters which are designed by introducing an orthogonality into the objective function can extract good discriminative features. Moreover, the experiment result suggests that the proposed method can automatically detect and extract brain activities related to motor imagery.

Optimizing RF gun cavity geometry within an automated injector design system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alicia Hofler ,Pavel Evtushenko

2011-03-28

RF guns play an integral role in the success of several light sources around the world, and properly designed and optimized cw superconducting RF (SRF) guns can provide a path to higher average brightness. As the need for these guns grows, it is important to have automated optimization software tools that vary the geometry of the gun cavity as part of the injector design process. This will allow designers to improve existing designs for present installations, extend the utility of these guns to other applications, and develop new designs. An evolutionary algorithm (EA) based system can provide this capability becausemore » EAs can search in parallel a large parameter space (often non-linear) and in a relatively short time identify promising regions of the space for more careful consideration. The injector designer can then evaluate more cavity design parameters during the injector optimization process against the beam performance requirements of the injector. This paper will describe an extension to the APISA software that allows the cavity geometry to be modified as part of the injector optimization and provide examples of its application to existing RF and SRF gun designs.« less

Phenomena induced by charged particle beams. [experimental design for Spacelab

NASA Technical Reports Server (NTRS)

Beghin, C.

1981-01-01

The injection of energetic particles along the Earth's magnetic field lines is a possible remote sensing method for measuring the electric fields parallel to the magnetic field with good time resolution over the entire magnetic field. Neutralization processes, return-current effects, dynamics of the beams, triggered instabilities, and waves must be investigated before the fundamental question about proper experimental conditions, such as energy, intensity and divergence of the beams, pitch-angle injection, ion species, proper probes and detectors and their location, and rendezvous conditions, can be resolved. An experiment designed to provide a better understanding of these special physical processes and to provide some answers to questions concerning beam injection techniques is described.

Designing and assessing fixed dental prostheses 2 multimedia-based education in dentistry students

PubMed Central

Jahandideh, Yousef; Roohi Balasi, Leila; Vadiati Saberi, Bardia; Dadgaran, Ideh

2016-01-01

Background: Above all methods effective learning results from decent training, acquired in the proper environment and encouraging creative methods. Computer-assisted training by educational software is considered a fundamental measure to improve medical and dentistry education systems. This study aims to design and assess fixed dental prostheses via 2 multimedia instructional contents at the Guilan dentistry school. Methods: This is a descriptive and cross-sectional study. First off, the instructional content was analyzed. The software used to produce multimedia was the iSpring suite Ver.7.0. After designing the instructional multimedia, this software was loaded by LMS. Sixty-nine dentistry students in the 5th semester at Guilan Dentistry School were selected via convenience sampling. At the end of the course, a structured questionnaire containing 26 items were handed to the students to evaluate the instructional multimedia quality. Results: Mean ±SD age was 24.68±3.24 years, 43 were women (62.4%) and 26 were men (37.6%) –the majority of 76.8% used the internet at home. A portion of 33.3% were inclined to use multimedia and the internet with in-person training. About 60% declared that multimedia quality as being good. Conclusion: the instructional multimedia designs which are compatible with lesson objectives and audiovisual facilities can have a great effect on the student's satisfaction. Preparing instructional multimedia makes the instructional content easily accessible for students to be able to review it several times at the proper opportunity and if presented through LMS they would be able to study the lesson subject wherever and whenever accessing the internet. PMID:28491830

Evaluation Results of an Ontology-based Design Model of Virtual Environments for Upper Limb Motor Rehabilitation of Stroke Patients.

PubMed

Ramírez-Fernández, Cristina; Morán, Alberto L; García-Canseco, Eloísa; Gómez-Montalvo, Jorge R

2017-03-23

1) To enhance the content of an ontology for designing virtual environments (VEs) for upper limb motor rehabilitation of stroke patients according to the suggestions and comments of rehabilitation specialists and software developers, 2) to characterize the perceived importance level of the ontology, 3) to determine the perceived usefulness of the ontology, and 4) to identify the safety characteristics of the ontology for VEs design according to the rehabilitation specialists. Using two semi-structured Web questionnaires, we asked six rehabilitation specialists and six software developers to provide us with their perception regarding the level of importance and the usability of the ontology. From their responses we have identified themes related to perceived and required safety characteristics of the ontology. Significant differences in the importance level were obtained for the Stroke Disability, VE Configuration, Outcome Measures, and Safety Calibration classes, which were perceived as highly important by rehabilitation specialists. Regarding usability, the ontology was perceived by both groups with high usefulness, ease of use, learnability and intention of use. Concerning the thematic analysis of recommendations, eight topics for safety characteristics of the ontology were identified: adjustment of therapy strategies; selection and delimitation of movements; selection and proper calibration of the interaction device; proper selection of measuring instruments; gradual modification of the difficulty of the exercise; adaptability and variability of therapy exercises; feedback according to the capabilities of the patient; and real-time support for exercise training. The rehabilitation specialists and software developers confirmed the importance of the information contained in the ontology regarding motor rehabilitation of the upper limb. Their recommendations highlight the safety features and the advantages of the ontology as a guide for the effective design of VEs.

PISCES High Contrast Integral Field Spectrograph Simulations and Data Reduction Pipeline

NASA Technical Reports Server (NTRS)

Llop Sayson, Jorge Domingo; Memarsadeghi, Nargess; McElwain, Michael W.; Gong, Qian; Perrin, Marshall; Brandt, Timothy; Grammer, Bryan; Greeley, Bradford; Hilton, George; Marx, Catherine

2015-01-01

The PISCES (Prototype Imaging Spectrograph for Coronagraphic Exoplanet Studies) is a lenslet array based integral field spectrograph (IFS) designed to advance the technology readiness of the WFIRST (Wide Field Infrared Survey Telescope)-AFTA (Astrophysics Focused Telescope Assets) high contrast Coronagraph Instrument. We present the end to end optical simulator and plans for the data reduction pipeline (DRP). The optical simulator was created with a combination of the IDL (Interactive Data Language)-based PROPER (optical propagation) library and Zemax (a MatLab script), while the data reduction pipeline is a modified version of the Gemini Planet Imager's (GPI) IDL pipeline. The simulations of the propagation of light through the instrument are based on Fourier transform algorithms. The DRP enables transformation of the PISCES IFS data to calibrated spectral data cubes.

Tunable antenna radome based on graphene frequency selective surface

NASA Astrophysics Data System (ADS)

Qu, Meijun; Rao, Menglou; Li, Shufang; Deng, Li

2017-09-01

In this paper, a graphene-based frequency selective surface (FSS) is proposed. The proposed FSS exhibits a tunable bandpass filtering characteristic due to the alterable conductivity of the graphene strips which is controlled by chemical potential. Based on the reconfigurable bandpass property of the proposed FSS, a cylindrical antenna radome is designed using the FSS unit cells. A conventional omnidirectional dipole can realize a two-beam directional pattern when it is placed into the proposed antenna radome. Forward and backward endfire radiations of the dipole loaded with the radome is realized by properly adjusting the chemical potential. The proposed antenna radome is extremely promising for beam-scanning in terahertz and mid-infrared plasmonic devices and systems when the gain of a conventional antenna needs to be enhanced.

Linear time-invariant controller design for two-channel decentralized control systems

NASA Technical Reports Server (NTRS)

Desoer, Charles A.; Gundes, A. Nazli

1987-01-01

This paper analyzes a linear time-invariant two-channel decentralized control system with a 2 x 2 strictly proper plant. It presents an algorithm for the algebraic design of a class of decentralized compensators which stabilize the given plant.

User Interface Design for Dynamic Geometry Software

ERIC Educational Resources Information Center

Kortenkamp, Ulrich; Dohrmann, Christian

2010-01-01

In this article we describe long-standing user interface issues with Dynamic Geometry Software and common approaches to address them. We describe first prototypes of multi-touch-capable DGS. We also give some hints on the educational benefits of proper user interface design.

Committee Report: Metrics & Methods for MF/UF System Optimization

EPA Science Inventory

After a membrane filtration (i.e., microfiltration (MF) and ultrafiltration (UF)) system is designed, installed, and commissioned, it is essential that the plant is well-maintained in order to proactively identify potential design or equipment problems and ensure its proper opera...

Design philosophy and operating experience with the WNRE Hot Cell Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, R.G.; Seymour, C.G.; Ryz, M.A.

1969-10-15

The objective of radiation safety and operating efficiency often conflict. The key to preventing this conflict is proper design. In this paper we discuss how both objectives have been met in the Whiteshell Nuclear Research Establishment (WNRE) Hot Cell Facilities.

Structure and Management of an Engineering Senior Design Course.

PubMed

Tanaka, Martin L; Fischer, Kenneth J

2016-07-01

The design of products and processes is an important area in engineering. Students in engineering schools learn fundamental principles in their courses but often lack an opportunity to apply these methods to real-world problems until their senior year. This article describes important elements that should be incorporated into a senior capstone design course. It includes a description of the general principles used in engineering design and a discussion of why students often have difficulty with application and revert to trial and error methods. The structure of a properly designed capstone course is dissected and its individual components are evaluated. Major components include assessing resources, identifying projects, establishing teams, understanding requirements, developing conceptual designs, creating detailed designs, building prototypes, testing performance, and final presentations. In addition to the course design, team management and effective mentoring are critical to success. This article includes suggested guidelines and tips for effective design team leadership, attention to detail, investment of time, and managing project scope. Furthermore, the importance of understanding business culture, displaying professionalism, and considerations of different types of senior projects is discussed. Through a well-designed course and proper mentoring, students will learn to apply their engineering skills and gain basic business knowledge that will prepare them for entry-level positions in industry.

Advanced gearbox technology

NASA Technical Reports Server (NTRS)

Anderson, N. E.; Cedoz, R. W.; Salama, E. E.; Wagner, D. A.

1987-01-01

An advanced 13,000 HP, counterrotating (CR) gearbox was designed and successfully tested to provide a technology base for future designs of geared propfan propulsion systems for both commercial and military aircraft. The advanced technology CR gearbox was designed for high efficiency, low weight, long life, and improved maintainability. The differential planetary CR gearbox features double helical gears, double row cylindrical roller bearings integral with planet gears, tapered roller prop support bearings, and a flexible ring gear and diaphragm to provide load sharing. A new Allison propfan back-to-back gearbox test facility was constructed. Extensive rotating and stationary instrumentation was used to measure temperature, strain, vibration, deflection and efficiency under representative flight operating conditions. The tests verified smooth, efficient gearbox operation. The highly-instrumented advanced CR gearbox was successfully tested to design speed and power (13,000 HP), and to a 115 percent overspeed condition. Measured CR gearbox efficiency was 99.3 percent at the design point based on heat loss to the oil. Tests demonstrated low vibration characteristics of double helical gearing, proper gear tooth load sharing, low stress levels, and the high load capacity of the prop tapered roller bearings. Applied external prop loads did not significantly affect gearbox temperature, vibration, or stress levels. Gearbox hardware was in excellent condition after the tests with no indication of distress.

Minimizing Artifacts and Biases in Chamber-Based Measurements of Soil Respiration

NASA Astrophysics Data System (ADS)

Davidson, E. A.; Savage, K.

2001-05-01

Soil respiration is one of the largest and most important fluxes of carbon in terrestrial ecosystems. The objectives of this paper are to review concerns about uncertainties of chamber-based measurements of CO2 emissions from soils, to evaluate the direction and magnitude of these potential errors, and to explain procedures that minimize these errors and biases. Disturbance of diffusion gradients cause underestimate of fluxes by less than 15% in most cases, and can be partially corrected for with curve fitting and/or can be minimized by using brief measurement periods. Under-pressurization or over-pressurization of the chamber caused by flow restrictions in air circulating designs can cause large errors, but can also be avoided with properly sized chamber vents and unrestricted flows. Somewhat larger pressure differentials are observed under windy conditions, and the accuracy of measurements made under such conditions needs more research. Spatial and temporal heterogeneity can be addressed with appropriate chamber sizes and numbers and frequency of sampling. For example, means of 8 randomly chosen flux measurements from a population of 36 measurements made with 300 cm2 chambers in tropical forests and pastures were within 25% of the full population mean 98% of the time and were within 10% of the full population mean 70% of the time. Comparisons of chamber-based measurements with tower-based measurements of total ecosystem respiration require analysis of the scale of variation within the purported tower footprint. In a forest at Howland, Maine, the differences in soil respiration rates among very poorly drained and well drained soils were large, but they mostly were fortuitously cancelled when evaluated for purported tower footprints of 600-2100 m length. While all of these potential sources of measurement error and sampling biases must be carefully considered, properly designed and deployed chambers provide a reliable means of accurately measuring soil respiration in terrestrial ecosystems.

Sustainability Engineering and Maintenance - Plan, Design, and Construct for Maintainability: Sustainable Lighting Systems

DTIC Science & Technology

2011-01-01

Window film should be considered to control heat gain. Skylights when positioned and spaced properly with the proper lens systems, admit more light...per unit area than windows, and distribute the light more evenly over the space. Skylights are mainly recommended in single floor high bay...facilities such as warehouses, hangars, gymnasiums, and big box stores.  The optimum material to use for skylights is either glass or acrylic. Double

Medical management of youth baseball and softball tournaments.

PubMed

Kanaan, Matthew; Ray, Tracy R

2013-01-01

The medical management of youth baseball and softball tournaments requires both proper planning and a basic awareness of commonly seen sport-specific injuries. While youth sporting events are designed to be a fun experience for all, injuries and emergencies will occur. With proper planning, and supplies, the impact of these issues can be minimized. This article will outline some basic principles for the medical personnel that may be involved in youth baseball and softball events.

Practical Considerations for Using Constant Force Springs in Space-Based Mechanisms

NASA Technical Reports Server (NTRS)

Williams, R. Brett; Fisher, Charles D.; Gallon, John C.

2013-01-01

Mechanical springs are a common element in mechanism from all walks of life; cars, watches, appliances, and many others. These springs generally exhibit a linear relationship between force and deflection. In small mechanisms, deflections are small so the variation in spring force between one position and another are generally small and do not influence the design or functionality of the device. However, as the spacecraft industry drives towards larger, deployable satellites, the distances a spring or springs must function over can become considerable so much so that the structural integrity of the device may be impacted. As such, an increasingly common mechanism element is the constant force spring- one that provides a constant force regardless of deflection. These elements are commonly in the conceptual design phase to deal with system-level large deflections, but in the detailed design or integration test phase they can pose significant implementation issues. This article addresses some of the detailed issues in order for these constant force springs to be properly designed into space systems.

Regulatory considerations in the design of comparative observational studies using propensity scores.

PubMed

Yue, Lilly Q

2012-01-01

In the evaluation of medical products, including drugs, biological products, and medical devices, comparative observational studies could play an important role when properly conducted randomized, well-controlled clinical trials are infeasible due to ethical or practical reasons. However, various biases could be introduced at every stage and into every aspect of the observational study, and consequently the interpretation of the resulting statistical inference would be of concern. While there do exist statistical techniques for addressing some of the challenging issues, often based on propensity score methodology, these statistical tools probably have not been as widely employed in prospectively designing observational studies as they should be. There are also times when they are implemented in an unscientific manner, such as performing propensity score model selection for a dataset involving outcome data in the same dataset, so that the integrity of observational study design and the interpretability of outcome analysis results could be compromised. In this paper, regulatory considerations on prospective study design using propensity scores are shared and illustrated with hypothetical examples.

Design optimization of an ironless inductive position sensor for the LHC collimators

NASA Astrophysics Data System (ADS)

Danisi, A.; Masi, A.; Losito, R.; Perriard, Y.

2013-09-01

The Ironless Inductive Position Sensor (I2PS) is an air-cored displacement sensor which has been conceived to be totally immune to external DC/slowly-varying magnetic fields. It can thus be used as a valid alternative to Linear Variable Differential Transformers (LVDTs), which can show a position error in magnetic environments. In addition, since it retains the excellent properties of LVDTs, the I2PS can be used in harsh environments, such as nuclear plants, plasma control and particle accelerators. This paper focuses on the design optimization of the sensor, considering the CERN LHC Collimators as application. In particular, the optimization comes after a complete review of the electromagnetic and thermal modeling of the sensor, as well as the proper choice of the reading technique. The design optimization stage is firmly based on these preliminary steps. Therefore, the paper summarises the sensor's complete development, from its modeling to its actual implementation. A set of experimental measurements demonstrates the sensor's performances to be those expected in the design phase.

Theory and simulation of DNA-coated colloids: a guide for rational design.

PubMed

Angioletti-Uberti, Stefano; Mognetti, Bortolo M; Frenkel, Daan

2016-03-07

By exploiting the exquisite selectivity of DNA hybridization, DNA-coated colloids (DNACCs) can be made to self-assemble in a wide variety of structures. The beauty of this system stems largely from its exceptional versatility and from the fact that a proper choice of the grafted DNA sequences yields fine control over the colloidal interactions. Theory and simulations have an important role to play in the optimal design of self assembling DNACCs. At present, the powerful model-based design tools are not widely used, because the theoretical literature is fragmented and the connection between different theories is often not evident. In this Perspective, we aim to discuss the similarities and differences between the different models that have been described in the literature, their underlying assumptions, their strengths and their weaknesses. Using the tools described in the present Review, it should be possible to move towards a more rational design of novel self-assembling structures of DNACCs and, more generally, of systems where ligand-receptor are used to control interactions.

Adapting the design of Anesthesia Information Management Systems to innovations depicted in Industrial Property documents.

PubMed

Spyropoulos, B; Tzavaras, A; Zogogianni, D; Botsivaly, M

2013-01-01

The purpose of this paper is to present the design and the current development status of an Anesthesia Information Management System (AIMS). For this system, the physical and technical advances, depicted in relevant, recently published Industrial Property documents, have been taken into account. Additional innovative sensors create further data-load to be managed. Novel wireless data-transmission modes demand eventually compliance to further proper standards, so that interoperability between AIMS and the existing Hospital Information Systems is being sustained. We attempted to define, the state-of-the-art concerning the functions, the design-prerequisites and the relevant standards and of an "emerging" AIMS that is combining hardware innovation, real-time data acquisition, processing and displaying and lastly enabling the necessary interoperability with the other components of the existing Hospital Information Systems. Finally, we report based on this approach, about the design and implementation status, of our "real-world" system under development and discuss the multifarious obstacles encountered during this still on-going project.

Design of the PET-MR system for head imaging of the DREAM Project

NASA Astrophysics Data System (ADS)

González, A. J.; Conde, P.; Hernández, L.; Herrero, V.; Moliner, L.; Monzó, J. M.; Orero, A.; Peiró, A.; Rodríguez-Álvarez, M. J.; Ros, A.; Sánchez, F.; Soriano, A.; Vidal, L. F.; Benlloch, J. M.

2013-02-01

In this paper we describe the overall design of a PET-MR system for head imaging within the framework of the DREAM Project as well as the first detector module tests. The PET system design consists of 4 rings of 16 detector modules each and it is expected to be integrated in a head dedicated radio frequency coil of an MR scanner. The PET modules are based on monolithic LYSO crystals coupled by means of optical devices to an array of 256 Silicon Photomultipliers. These types of crystals allow to preserve the scintillation light distribution and, thus, to recover the exact photon impact position with the proper characterization of such a distribution. Every module contains 4 Application Specific Integrated Circuits (ASICs) which return detailed information of several light statistical momenta. The preliminary tests carried out on this design and controlled by means of ASICs have shown promising results towards the suitability of hybrid PET-MR systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marchisio, Mario Andrea, E-mail: marchisio@hit.edu.cn

Published in 2008, Parts & Pools represents one of the first attempts to conceptualize the modular design of bacterial synthetic gene circuits with Standard Biological Parts (DNA segments) and Pools of molecules referred to as common signal carriers (e.g., RNA polymerases and ribosomes). The original framework for modeling bacterial components and designing prokaryotic circuits evolved over the last years and brought, first, to the development of an algorithm for the automatic design of Boolean gene circuits. This is a remarkable achievement since gene digital circuits have a broad range of applications that goes from biosensors for health and environment caremore » to computational devices. More recently, Parts & Pools was enabled to give a proper formal description of eukaryotic biological circuit components. This was possible by employing a rule-based modeling approach, a technique that permits a faithful calculation of all the species and reactions involved in complex systems such as eukaryotic cells and compartments. In this way, Parts & Pools is currently suitable for the visual and modular design of synthetic gene circuits in yeast and mammalian cells too.« less

13C-based metabolic flux analysis: fundamentals and practice.

PubMed

Yang, Tae Hoon

2013-01-01

Isotope-based metabolic flux analysis is one of the emerging technologies applied to system level metabolic phenotype characterization in metabolic engineering. Among the developed approaches, (13)C-based metabolic flux analysis has been established as a standard tool and has been widely applied to quantitative pathway characterization of diverse biological systems. To implement (13)C-based metabolic flux analysis in practice, comprehending the underlying mathematical and computational modeling fundamentals is of importance along with carefully conducted experiments and analytical measurements. Such knowledge is also crucial when designing (13)C-labeling experiments and properly acquiring key data sets essential for in vivo flux analysis implementation. In this regard, the modeling fundamentals of (13)C-labeling systems and analytical data processing are the main topics we will deal with in this chapter. Along with this, the relevant numerical optimization techniques are addressed to help implementation of the entire computational procedures aiming at (13)C-based metabolic flux analysis in vivo.

Laboratory Experimental Design for a Glycomic Study.

PubMed

Ugrina, Ivo; Campbell, Harry; Vučković, Frano

2017-01-01

Proper attention to study design before, careful conduct of procedures during, and appropriate inference from results after scientific experiments are important in all scientific studies in order to ensure valid and sometimes definitive conclusions can be made. The design of experiments, also called experimental design, addresses the challenge of structuring and conducting experiments to answer the questions of interest as clearly and efficiently as possible.

Design and Development of the Space Shuttle Tail Service Masts

NASA Technical Reports Server (NTRS)

Dandage, S. R.; Herman, N. A.; Godfrey, S. E.; Uda, R. T.

1977-01-01

The successful launch of a space shuttle vehicle depends on the proper operation of two tail service masts (TSMs). Reliable TSM operation is assured through a comprehensive design, development, and testing program. The results of the concept verification test (CVT) and the resulting impact on prototype TSM design are presented. The design criteria are outlined, and the proposed prototype TSM tests are described.

An Intuitive Graphical Approach to Understanding the Split-Plot Experiment

ERIC Educational Resources Information Center

Robinson, Timothy J.; Brenneman, William A.; Myers, William R.

2009-01-01

While split-plot designs have received considerable attention in the literature over the past decade, there seems to be a general lack of intuitive understanding of the error structure of these designs and the resulting statistical analysis. Typically, students learn the proper error terms for testing factors of a split-plot design via "expected…

A discussion of higher order software concepts as they apply to functional requirements and specifications. [space shuttles and guidance

NASA Technical Reports Server (NTRS)

Hamilton, M.

1973-01-01

The entry guidance software functional requirements (requirements design phase), its architectural requirements (specifications design phase), and the entry guidance software verified code are discussed. It was found that the proper integration of designs at both the requirements and specifications levels are of high priority consideration.

Onboard TDI stage estimation and calibration using SNR analysis

NASA Astrophysics Data System (ADS)

Haghshenas, Javad

2017-09-01

Electro-Optical design of a push-broom space camera for a Low Earth Orbit (LEO) remote sensing satellite is performed based on the noise analysis of TDI sensors for very high GSDs and low light level missions. It is well demonstrated that the CCD TDI mode of operation provides increased photosensitivity relative to a linear CCD array, without the sacrifice of spatial resolution. However, for satellite imaging, in order to utilize the advantages which the TDI mode of operation offers, attention should be given to the parameters which affect the image quality of TDI sensors such as jitters, vibrations, noises and etc. A predefined TDI stages may not properly satisfy image quality requirement of the satellite camera. Furthermore, in order to use the whole dynamic range of the sensor, imager must be capable to set the TDI stages in every shots based on the affecting parameters. This paper deals with the optimal estimation and setting the stages based on tradeoffs among MTF, noises and SNR. On-board SNR estimation is simulated using the atmosphere analysis based on the MODTRAN algorithm in PcModWin software. According to the noises models, we have proposed a formulation to estimate TDI stages in such a way to satisfy the system SNR requirement. On the other hand, MTF requirement must be satisfy in the same manner. A proper combination of both parameters will guaranty the full dynamic range usage along with the high SNR and image quality.

The promise--and peril--of integrated cost systems.

PubMed

Cooper, R; Kaplan, R S

1998-01-01

Recent advances in managerial accounting have helped executives get the information they need to make good strategic decisions. But today's enterprise resource planning systems promise even greater benefits--the chance to integrate activity-based costing, operational-control, and financial reporting systems. But managers need to approach integration very thoughtfully, or they could end up with a system that drives decision making in the wrong direction. Operational-control and ABC systems have fundamentally different purposes. Their requirements for accuracy, timeliness, and aggregation are so different that no single, fully integrated approach can be adequate for both purposes. If an integrated system used real-time cost data instead of standard rates in its ABC subsystem, for example, the result would be dangerously distorted messages about individual product profitability--and that's precisely the problem ABC systems were originally designed to address. Proper linkage and feedback between the two systems is possible, however. Through activity-based budgeting, the ABC system is linked directly to operations control: managers can determine the supply and practical capacity of resources in forthcoming periods. Linking operational control to ABC is also possible. The activity-based portion of an operational control system collects information that, while it mustn't be fed directly into the activity-based strategic cost system, can be extremely useful once it's been properly analyzed. Finally, ABC and operational control can be linked to financial reporting to generate cost of goods sold and inventory valuations--but again, with precautions.

Hurdle models for multilevel zero-inflated data via h-likelihood.

PubMed

Molas, Marek; Lesaffre, Emmanuel

2010-12-30

Count data often exhibit overdispersion. One type of overdispersion arises when there is an excess of zeros in comparison with the standard Poisson distribution. Zero-inflated Poisson and hurdle models have been proposed to perform a valid likelihood-based analysis to account for the surplus of zeros. Further, data often arise in clustered, longitudinal or multiple-membership settings. The proper analysis needs to reflect the design of a study. Typically random effects are used to account for dependencies in the data. We examine the h-likelihood estimation and inference framework for hurdle models with random effects for complex designs. We extend the h-likelihood procedures to fit hurdle models, thereby extending h-likelihood to truncated distributions. Two applications of the methodology are presented. Copyright © 2010 John Wiley & Sons, Ltd.

Glucose determination in human aqueous humor with Raman spectroscopy

NASA Technical Reports Server (NTRS)

Lambert, James L.; Pelletier, Christine C.; Borchert, Mark

2005-01-01

It has been suggested that spectroscopic analysis of the aqueous humor of the eye could be used to indirectly predict blood glucose levels in diabetics noninvasively. We have been investigating this potential using Raman spectroscopy in combination with partial least squares (PLS) analysis. We have determined that glucose at clinically relevant concentrations can be accurately predicted in human aqueous humor in vitro using a PLS model based on artificial aqueous humor. We have further determined that with proper instrument design, the light energy necessary to achieve clinically acceptable prediction of glucose does not damage the retinas of rabbits and can be delivered at powers below internationally acceptable safety limits. Herein we summarize our current results and address our strategies to improve instrument design. 2005 Society of Photo-Optical Instrumentation Engineers.

Composite correlation filter for O-ring detection in stationary colored noise

NASA Astrophysics Data System (ADS)

Hassebrook, Laurence G.

2009-04-01

O-rings are regularly replaced in aircraft and if they are not replaced or if they are installed improperly, they can result in catastrophic failure of the aircraft. It is critical that the o-rings be packaged correctly to avoid mistakes made by technicians during routine maintenance. For this reason, fines may be imposed on the o-ring manufacturer if the o-rings are packaged incorrectly. That is, a single o-ring must be packaged and labeled properly. No o-rings or more than one o-ring per package is not acceptable. We present an industrial inspection system based on real-time composite correlation filtering that has successfully solved this problem in spite of opaque paper o-ring packages. We present the system design including the composite filter design.

Tectonic characterization of a potential high-level nuclear waste repository at Yucca Mountain, Nevada

USGS Publications Warehouse

Whitney, John W.; O'Leary, Dennis W.

1993-01-01

Tectonic characterization of a potential high-level nuclear waste repository at Yucca Mountain, Nevada, is needed to assess seismic and possible volcanic hazards that could affect the site during the preclosure (next 100 years) and the behavior of the hydrologic system during the postclosure (the following 10,000 years) periods. Tectonic characterization is based on assembling mapped geological structures in their chronological order of development and activity, and interpreting their dynamic interrelationships. Addition of mechanistic models and kinematic explanations for the identified tectonic processes provides one or more tectonic models having predictive power. Proper evaluation and application of tectonic models can aid in seismic design and help anticipate probable occurrence of future geologic events of significance to the repository and its design.

Design and fabrication of novel anode flow-field for commercial size solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Canavar, Murat; Timurkutluk, Bora

2017-04-01

In this study, nickel based woven meshes are tested as not only anode current collecting meshes but also anode flow fields instead of the conventional gas channels fabricated by machining. For this purpose, short stacks with different anode flow fields are designed and built by using different number of meshes with various wire diameters and widths of opening. A short stack with classical machined flow channels is also constructed. Performance and impedance measurements of the short stacks with commercial size cells of 81 cm2 active area are performed and compared. The results reveal that it is possible to create solid oxide fuel cell anode flow fields with woven meshes and obtain acceptable power with a proper selection of the mesh number, type and orientation.

Designing torus-doubling solutions to discrete time systems by hybrid projective synchronization

NASA Astrophysics Data System (ADS)

Xie, Hui; Wen, Guilin

2013-11-01

Doubling of torus occurs in high dimensional nonlinear systems, which is related to a certain kind of typical second bifurcations. It is a nontrivial task to create a torus-doubling solution with desired dynamical properties based on the classical bifurcation theories. In this paper, dead-beat hybrid projective synchronization is employed to build a novel method for designing stable torus-doubling solutions into discrete time systems with proper properties to achieve the purpose of utilizing bifurcation solutions as well as avoiding the possible conflict of physical meaning of the created solution. Although anti-controls of bifurcation and chaos synchronizations are two different topics in nonlinear dynamics and control, the results imply that it is possible to develop some new interdisciplinary methods between chaos synchronization and anti-controls of bifurcations.

Summary of spin technology as related to light general-aviation airplanes

NASA Technical Reports Server (NTRS)

Bowman, J. S., Jr.

1971-01-01

A summary was made of all NASA (and NACA) research and experience related to the spin and recovery characteristics of light personal-owner-type general-aviation airplanes. Very little of the research deals with light general-aviation airplanes as such, but many of the airplanes and models tested before and during World War II were similar to present-day light general-aviation airplanes with regard to the factors that are important in spinning. The material is based mainly on the results of spin-tunnel tests of free-spinning dynamically scaled models of about 100 different airplane designs and, whenever possible, includes correlation with full-scale spin tests. The research results are discussed in terms of airplane design considerations and the proper use of controls for recovery.

37 CFR 262.7 - Verification of royalty payments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Designated Agent have agreed as to proper verification methods. (b) Frequency of verification. A Copyright Owner or a Performer may conduct a single audit of the Designated Agent upon reasonable notice and... COPYRIGHT ARBITRATION ROYALTY PANEL RULES AND PROCEDURES RATES AND TERMS FOR CERTAIN ELIGIBLE...

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

Budget-Minded Renovation Lights Up Students' Learning.

ERIC Educational Resources Information Center

McDaniel, Craig

1998-01-01

Provides considerations for educational facility lighting designs that support student learning while controlling costs. Lighting design decision factors include the types of classroom activities involved, the importance of properly using artificial and indirect lighting, the importance of color rendering, the positioning of windows and skylights,…

Safe and Sanitary.

ERIC Educational Resources Information Center

Turner, Ed; Hauser, Dan

1994-01-01

Explains how daily maintenance and design planning can reduce the potential safety hazards found in athletic-facility locker rooms. Topics include designing locker rooms for visual openness and traffic control, providing non-slip surfaces and proper drainage, installing ventilation systems that can handle the moisture produced in locker rooms,…

Evaluation of drainage pipe by field experimentation and supplemental laboratory experimentation : final report.

DOT National Transportation Integrated Search

1985-03-01

Louisiana's Office of Highways reacts to a major problem when it attempts to shape and control drainage patterns along its right-of-ways. The Office's design engineers meet this challenge through proper section design and appropriate application of d...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

Evaluation of drainage pipe by field experimentation and supplemental laboratory experimentation : interim report No. 3.

DOT National Transportation Integrated Search

1981-11-01

The Louisiana Department of Transportation and Development reacts to a major problem when it attempts to shape and control drainage patterns along its right-of-ways. The Department's design engineers meet this challenge through proper section design ...

On long-time instabilities in staggered finite difference simulations of the seismic acoustic wave equations on discontinuous grids

NASA Astrophysics Data System (ADS)

Gao, Longfei; Ketcheson, David; Keyes, David

2018-02-01

We consider the long-time instability issue associated with finite difference simulation of seismic acoustic wave equations on discontinuous grids. This issue is exhibited by a prototype algebraic problem abstracted from practical application settings. Analysis of this algebraic problem leads to better understanding of the cause of the instability and provides guidance for its treatment. Specifically, we use the concept of discrete energy to derive the proper solution transfer operators and design an effective way to damp the unstable solution modes. Our investigation shows that the interpolation operators need to be matched with their companion restriction operators in order to properly couple the coarse and fine grids. Moreover, to provide effective damping, specially designed diffusive terms are introduced to the equations at designated locations and discretized with specially designed schemes. These techniques are applied to simulations in practical settings and are shown to lead to superior results in terms of both stability and accuracy.

SKYSHINE-II procedure: calculation of the effects of structure design on neutron, primary gamma-ray and secondary gamma-ray dose rates in air. Supplement number 1. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lampley, C.M.

1981-01-01

This report describes many of the computational methods employed within the SKYSHINE-II program. A brief description of the new data base is included, as is a description of the input data requirements and formats needed to properly execute a SKYSHINE-II problem. Utilization instructions for the program are provided for operation of the SKYSHINE-II Code on the Brookhaven National Laboratory Central Scientific Computing Facility (See NUREG/CR-0781, RRA-T7901 for complete information).

Fluorescent Quantum Dots for Biological Labeling

NASA Technical Reports Server (NTRS)

McDonald, Gene; Nadeau, Jay; Nealson, Kenneth; Storrie-Lomardi, Michael; Bhartia, Rohit

2003-01-01

Fluorescent semiconductor quantum dots that can serve as "on/off" labels for bacteria and other living cells are undergoing development. The "on/off" characterization of these quantum dots refers to the fact that, when properly designed and manufactured, they do not fluoresce until and unless they come into contact with viable cells of biological species that one seeks to detect. In comparison with prior fluorescence-based means of detecting biological species, fluorescent quantum dots show promise for greater speed, less complexity, greater sensitivity, and greater selectivity for species of interest. There are numerous potential applications in medicine, environmental monitoring, and detection of bioterrorism.

Short cavity DFB fiber laser based vector hydrophone for low frequency signal detection

NASA Astrophysics Data System (ADS)

Zhang, Xiaolei; Zhang, Faxiang; Jiang, Shaodong; Min, Li; Li, Ming; Peng, Gangding; Ni, Jiasheng; Wang, Chang

2017-12-01

A short cavity distributed feedback (DFB) fiber laser is used for low frequency acoustic signal detection. Three DFB fiber lasers with different central wavelengths are chained together to make three-element vector hydrophone with proper sensitivity enhancement design, which has extensive and significant applications to underwater acoustic monitoring for the national defense, oil, gas exploration, and so on. By wavelength-phase demodulation, the lasing wavelength changes under different frequency signals can be interpreted, and the sensitivity is tested about 33 dB re pm/g. The frequency response range is rather flat from 5 Hz to 300 Hz.

Simple morphological control over functional diversity of SERS materials

NASA Astrophysics Data System (ADS)

Semenova, A. A.; Goodilin, E. A.

2018-03-01

Nowadays, surface-enhanced Raman spectroscopy (SERS) becomes a promising universal low-cost and real-time tool in biomedical applications, medical screening or forensic analysis allowing for detection of different molecules below nanomolar concentrations. Silver nanoparticles and nanostructures have proven to be a common choice for SERS measurements due to a tunable plasmon resonance, high stability and facile fabrication methods. However, a proper design of silver-based nanomaterials for highly sensitive SERS applications still remains a challenge. In this work, effective and simple preparation methods of various silver nanostructures are proposed and systematically developed using aqueous diamminesilver (I) hydroxide as a precursor.

Inference Engine in an Intelligent Ship Course-Keeping System

PubMed Central

2017-01-01

The article presents an original design of an expert system, whose function is to automatically stabilize ship's course. The focus is put on the inference engine, a mechanism that consists of two functional components. One is responsible for the construction of state space regions, implemented on the basis of properly processed signals recorded by sensors from the input and output of an object. The other component is responsible for generating a control decision based on the knowledge obtained in the first module. The computing experiments described herein prove the effective and correct operation of the proposed system. PMID:29317859

75 W 40% efficiency single-mode all-fiber erbium-doped laser cladding pumped at 976 nm.

PubMed

Kotov, L V; Likhachev, M E; Bubnov, M M; Medvedkov, O I; Yashkov, M V; Guryanov, A N; Lhermite, J; Février, S; Cormier, E

2013-07-01

Optimization of Yb-free Er-doped fiber for lasers and amplifiers cladding pumped at 976 nm was performed in this Letter. The single-mode fiber design includes an increased core diameter of 34 μm and properly chosen erbium and co-dopant concentrations. We demonstrate an all-fiber high power laser and power amplifier based on this fiber with the record slope efficiency of 40%. To the best of our knowledge, the achieved output power of 75 W is the highest power reported for such lasers.

Fabrication of amorphous silica nanowires via oxygen plasma treatment of polymers on silicon

NASA Astrophysics Data System (ADS)

Chen, Zhuojie; She, Didi; Chen, Qinghua; Li, Yanmei; Wu, Wengang

2018-02-01

We demonstrate a facile non-catalytic method of fabricating silica nanowires at room temperature. Different polymers including photoresists, parylene C and polystyrene are patterned into pedestals on the silicon substrates. The silica nanowires are obtained via the oxygen plasma treatment on those pedestals. Compared to traditional strategies of silica nanowire fabrication, this method is much simpler and low-cost. Through designing the proper initial patterns and plasma process parameters, the method can be used to fabricate various regiment nano-scale silica structure arrays in any laboratory with a regular oxygen-plasma-based cleaner or reactive-ion-etching equipment.

Development and manufacture of visor for helmet-mounted display

NASA Astrophysics Data System (ADS)

Krevor, David H.; McNelly, Gregg; Skubon, John; Speirs, Robert

2004-01-01

The manufacturing design and process development for the Visor for the JHMCS (Joint Helmet Mounted Cueing System) are discussed. The JHMCS system is a Helmet Mounted Display (HMD) system currently flying on the F-15, F-16 and F/A-18 aircraft. The Visor manufacturing processes are essential to both system performance and economy. The Visor functions both as the system optical combiner and personal protective equipment for the pilot. The Visor material is optical polycarbonate. For a military HMD system, the mechanical and environmental properties of the Visor are as necessary as the optical properties. The visor must meet stringent dimensional requirements to assure adequate system optical performance. Injection molding can provide dimensional fidelity to the requirements, if done properly. Concurrent design of the visor and the tool (i.e., the injection mold) is essential. The concurrent design necessarily considers manufacturing operations and the use environment of the Visor. Computer modeling of the molding process is a necessary input to the mold design. With proper attention to product design and tool development, it is possible to improve upon published standard dimensional tolerances for molded polycarbonate articles.

Authentication techniques for smart cards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, R.A.

1994-02-01

Smart card systems are most cost efficient when implemented as a distributed system, which is a system without central host interaction or a local database of card numbers for verifying transaction approval. A distributed system, as such, presents special card and user authentication problems. Fortunately, smart cards offer processing capabilities that provide solutions to authentication problems, provided the system is designed with proper data integrity measures. Smart card systems maintain data integrity through a security design that controls data sources and limits data changes. A good security design is usually a result of a system analysis that provides a thoroughmore » understanding of the application needs. Once designers understand the application, they may specify authentication techniques that mitigate the risk of system compromise or failure. Current authentication techniques include cryptography, passwords, challenge/response protocols, and biometrics. The security design includes these techniques to help prevent counterfeit cards, unauthorized use, or information compromise. This paper discusses card authentication and user identity techniques that enhance security for microprocessor card systems. It also describes the analysis process used for determining proper authentication techniques for a system.« less

Optical Correlation of Images With Signal-Dependent Noise Using Constrained-Modulation Filter Devices

NASA Technical Reports Server (NTRS)

Downie, John D.

1995-01-01

Images with signal-dependent noise present challenges beyond those of images with additive white or colored signal-independent noise in terms of designing the optimal 4-f correlation filter that maximizes correlation-peak signal-to-noise ratio, or combinations of correlation-peak metrics. Determining the proper design becomes more difficult when the filter is to be implemented on a constrained-modulation spatial light modulator device. The design issues involved for updatable optical filters for images with signal-dependent film-grain noise and speckle noise are examined. It is shown that although design of the optimal linear filter in the Fourier domain is impossible for images with signal-dependent noise, proper nonlinear preprocessing of the images allows the application of previously developed design rules for optimal filters to be implemented on constrained-modulation devices. Thus the nonlinear preprocessing becomes necessary for correlation in optical systems with current spatial light modulator technology. These results are illustrated with computer simulations of images with signal-dependent noise correlated with binary-phase-only filters and ternary-phase-amplitude filters.

Computational Investigation of the NASA Cascade Cyclonic Separation Device

NASA Technical Reports Server (NTRS)

Hoyt, Nathaniel C.; Kamotani, Yasuhiro; Kadambi, Jaikrishnan; McQuillen, John B.; Sankovic, John M.

2008-01-01

Devices designed to replace the absent buoyancy separation mechanism within a microgravity environment are of considerable interest to NASA as the functionality of many spacecraft systems are dependent on the proper sequestration of interpenetrating gas and liquid phases. Inasmuch, a full multifluid Euler-Euler computational fluid dynamics investigation has been undertaken to evaluate the performance characteristics of one such device, the Cascade Cyclonic Separator, across a full range of inlet volumetric quality with combined volumetric injection rates varying from 1 L/min to 20 L/min. These simulations have delimited the general modes of operation of this class of devices and have proven able to describe the complicated vortex structure and induced pressure gradients that arise. The computational work has furthermore been utilized to analyze design modifications that enhance the overall performance of these devices. The promising results indicate that proper CFD modeling may be successfully used as a tool for microgravity separator design.

A long life 4 V class lithium-ion polymer battery with liquid-free polymer electrolyte

NASA Astrophysics Data System (ADS)

Kobayashi, Yo; Shono, Kumi; Kobayashi, Takeshi; Ohno, Yasutaka; Tabuchi, Masato; Oka, Yoshihiro; Nakamura, Tatsuya; Miyashiro, Hajime

2017-02-01

Ether-based solid polymer electrolyte (SPE) is one of the most well-known lithium ion conductors. Unlike the other inorganic electrolytes, SPE exhibits advantages of flexibility and large-area production, enabling low cost production of large size batteries. However, because the ether group is oxidized at 4 V versus Li/Li+ cathode, and due to its high irreversibility with the carbon anode, ether-based SPE was believed to be inapplicable to 4 V class lithium-ion batteries with carbon anode. Here we report a remarkably stable SPE in combination with a 4 V class cathode and carbon anode achieved by the proper design at the interface. The introduced boron-based lithium salt prohibits further oxidation of SPE at the cathode interface. The surface modification of graphite by the annealing of polyvinyl chloride mostly prohibits the continuous consumption of lithium at the graphite anode. Using above interface design, we achieved 60% capacity retention after 5400 cycles. The proposed battery provides a possible approach for realizing flammable electrolyte-free lithium-ion batteries, which achieve innovative safety improvements of large format battery systems for stationary use.

[Adequate application of quantitative and qualitative statistic analytic methods in acupuncture clinical trials].

PubMed

Tan, Ming T; Liu, Jian-ping; Lao, Lixing

2012-08-01

Recently, proper use of the statistical methods in traditional Chinese medicine (TCM) randomized controlled trials (RCTs) has received increased attention. Statistical inference based on hypothesis testing is the foundation of clinical trials and evidence-based medicine. In this article, the authors described the methodological differences between literature published in Chinese and Western journals in the design and analysis of acupuncture RCTs and the application of basic statistical principles. In China, qualitative analysis method has been widely used in acupuncture and TCM clinical trials, while the between-group quantitative analysis methods on clinical symptom scores are commonly used in the West. The evidence for and against these analytical differences were discussed based on the data of RCTs assessing acupuncture for pain relief. The authors concluded that although both methods have their unique advantages, quantitative analysis should be used as the primary analysis while qualitative analysis can be a secondary criterion for analysis. The purpose of this paper is to inspire further discussion of such special issues in clinical research design and thus contribute to the increased scientific rigor of TCM research.

Computationally efficient stochastic optimization using multiple realizations

NASA Astrophysics Data System (ADS)

Bayer, P.; Bürger, C. M.; Finkel, M.

2008-02-01

The presented study is concerned with computationally efficient methods for solving stochastic optimization problems involving multiple equally probable realizations of uncertain parameters. A new and straightforward technique is introduced that is based on dynamically ordering the stack of realizations during the search procedure. The rationale is that a small number of critical realizations govern the output of a reliability-based objective function. By utilizing a problem, which is typical to designing a water supply well field, several variants of this "stack ordering" approach are tested. The results are statistically assessed, in terms of optimality and nominal reliability. This study demonstrates that the simple ordering of a given number of 500 realizations while applying an evolutionary search algorithm can save about half of the model runs without compromising the optimization procedure. More advanced variants of stack ordering can, if properly configured, save up to more than 97% of the computational effort that would be required if the entire number of realizations were considered. The findings herein are promising for similar problems of water management and reliability-based design in general, and particularly for non-convex problems that require heuristic search techniques.

Statistical flaws in design and analysis of fertility treatment studies on cryopreservation raise doubts on the conclusions

PubMed Central

van Gelder, P.H.A.J.M.; Nijs, M.

2011-01-01

Decisions about pharmacotherapy are being taken by medical doctors and authorities based on comparative studies on the use of medications. In studies on fertility treatments in particular, the methodological quality is of utmost importance in the application of evidence-based medicine and systematic reviews. Nevertheless, flaws and omissions appear quite regularly in these types of studies. Current study aims to present an overview of some of the typical statistical flaws, illustrated by a number of example studies which have been published in peer reviewed journals. Based on an investigation of eleven studies at random selected on fertility treatments with cryopreservation, it appeared that the methodological quality of these studies often did not fulfil the required statistical criteria. The following statistical flaws were identified: flaws in study design, patient selection, and units of analysis or in the definition of the primary endpoints. Other errors could be found in p-value and power calculations or in critical p-value definitions. Proper interpretation of the results and/or use of these study results in a meta analysis should therefore be conducted with care. PMID:24753877

Statistical flaws in design and analysis of fertility treatment -studies on cryopreservation raise doubts on the conclusions.

PubMed

van Gelder, P H A J M; Nijs, M

2011-01-01

Decisions about pharmacotherapy are being taken by medical doctors and authorities based on comparative studies on the use of medications. In studies on fertility treatments in particular, the methodological quality is of utmost -importance in the application of evidence-based medicine and systematic reviews. Nevertheless, flaws and omissions appear quite regularly in these types of studies. Current study aims to present an overview of some of the typical statistical flaws, illustrated by a number of example studies which have been published in peer reviewed journals. Based on an investigation of eleven studies at random selected on fertility treatments with cryopreservation, it appeared that the methodological quality of these studies often did not fulfil the -required statistical criteria. The following statistical flaws were identified: flaws in study design, patient selection, and units of analysis or in the definition of the primary endpoints. Other errors could be found in p-value and power calculations or in critical p-value definitions. Proper -interpretation of the results and/or use of these study results in a meta analysis should therefore be conducted with care.

An Evaluation of the Vapor Phase Catalytic Ammonia Removal Process for Use in a Mars Transit Vehicle

NASA Technical Reports Server (NTRS)

Flynn, Michael; Borchers, Bruce

1998-01-01

An experimental program has been developed to evaluate the potential of the Vapor Phase Catalytic Ammonia Reduction (VPCAR) technology for use as a Mars Transit Vehicle water purification system. Design modifications which will be required to ensure proper operation of the VPCAR system in reduced gravity are also evaluated. The VPCAR system is an integrated wastewater treatment technology that combines a distillation process with high temperature catalytic oxidation. The distillation portion of the system utilizes a vapor compression distillation process to provide an energy efficient phase change separation. This portion of the system removes any inorganic salts and large molecular weight, organic contaminates, i.e., non-volatile, from the product water stream and concentrates these contaminates into a byproduct stream. To oxidize the volatile organic compounds and ammonia, a vapor phase, high temperature catalytic oxidizer is used. This catalytic system converts these compounds along with the aqueous product into CO2, H2O, and N2O. A secondary catalytic bed can then be used to reduce the N2O to nitrogen and oxygen (although not evaluated in this study). This paper describes the design specification of the VPCAR process, the relative benefits of its utilization in a Mars Transit Vehicle, and the design modification which will be required to ensure its proper operation in reduced gravity. In addition, the results of an experimental evaluation of the processors is presented. This evaluation presents the processors performance based upon product water purity, water recovery rates, and power.

Tests of oil scraper piston ring and piston fitted with oil drain holes

NASA Technical Reports Server (NTRS)

Mcdewell, H S

1922-01-01

Tests were conducted to determine whether or not a properly located and properly designed oil scraper piston ring, installed on a piston provided with oil drain holes of sufficient area, would prevent the excessive oiling of the Liberty engine, particularly with the engine running at idling speed with full oil pressure. Results showed that excessive oiling was in fact prevented. It is strongly recommended that scraper rings and pistons be adopted for aircraft engines.

Astronaut candidate Koichi Wakata (left) prepares to jump off a box during a parachute landing

NASA Technical Reports Server (NTRS)

1996-01-01

1992 ASCAN TRAINING --- Astronaut candidate Koichi Wakata (left) prepares to jump off a box during a parachute landing demonstration at Vance Air Force Base. This portion of the training is designed to familiarize the trainees with the proper way to hit the ground following a parachute jump. Looking on is astronaut candidate Andrew W. S. Thomas. Wakata is one of seven international mission specialist candidates who joined 19 United States astronaut candidates, including Thomas, for the three-day parachute/survival training school at the Oklahoma Base.EDITORS NOTE: Since this photograph was taken, Wakata has been named as mission specialist for the STS-72 mission and Thomas has been named as mission specialist for the STS-77 flight.

Master dye laser oscillator including a specific grating assembly for use therein

DOEpatents

Davin, James M.

1992-01-01

A dye laser oscillator for producing a tuned dye beam is disclosed herein and includes, among other components, a beam output coupling assembly, a dye cell assembly, a beam expander assembly, an etalon assembly, and a grating assembly. Each of three assemblies is vertically supported from a horizontal base so as to be readily removable from the base without interference from or interfering with the other assemblies. The particular grating assembly disclosed is specifically designed for proper optical alignment with the intended path of the dye beam to be produced and for accurate pivotal movement relative to the beam path in order to function as a coarse tuning mechanism in the production of the ultimately tuned beam.

Master dye laser oscillator including a specific grating assembly for use therein

DOEpatents

Davin, J.M.

1992-09-01

A dye laser oscillator for producing a tuned dye beam is disclosed herein and includes, among other components, a beam output coupling assembly, a dye cell assembly, a beam expander assembly, an etalon assembly, and a grating assembly. Each of three assemblies is vertically supported from a horizontal base so as to be readily removable from the base without interference from or interfering with the other assemblies. The particular grating assembly disclosed is specifically designed for proper optical alignment with the intended path of the dye beam to be produced and for accurate pivotal movement relative to the beam path in order to function as a coarse tuning mechanism in the production of the ultimately tuned beam. 5 figs.

Tunable graphene-based hyperbolic metamaterial operating in SCLU telecom bands.

PubMed

Janaszek, Bartosz; Tyszka-Zawadzka, Anna; Szczepański, Paweł

2016-10-17

The tunability of graphene-based hyperbolic metamaterial structure operating in SCLU telecom bands is investigated. For the first time it has been shown that for the proper design of a graphene/dielectric multilayer stack, the HMM Type I, Epsilon-Near-Zero and Type II regimes are possible by changing the biasing potential. Numerical results reveal the effect of structure parameters such as the thickness of the dielectric layer as well as a number of graphene sheets in a unit cell (i.e., dielectric/graphene bilayer) on the tunability range and shape of the dispersion characteristics (i.e., Type I/ENZ/Type II) in SCLU telecom bands. This kind of materials could offer a technological platform for novel devices having various applications in optical communications technology.

Role of Nutritional Supplements Complementing Nutrient-Dense Diets: General Versus Sport/Exercise-Specific Dietary Guidelines Related to Energy Expenditure

NASA Astrophysics Data System (ADS)

Kleiner, Susan; Greenwood, Mike

A nutrient-dense diet is a critical aspect in attaining optimal exercise training and athletic performance outcomes. Although including safe and effective nutritional supplements in the dietary design can be extremely helpful in promoting adequate caloric ingestion, they are not sufficient for promoting adequate caloric ingestion based on individualized caloric expenditure needs without the proper diet. Specifically, a strategic and scientifically based nutrient-dense dietary profile should be created by qualified professionals to meet the sport/exercise-specific energy demands of any individual involved in select training intensity protocols. Finally, ingesting the right quantity and quality of nutrient dense calories at precise windows of opportunity becomes vital in attaining desired training and/or competitive performance outcomes.

78 FR 49520 - Scientific Information Request on Imaging Techniques for the Surveillance, Diagnosis, and Staging...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-14

... conducting this comparative effectiveness review pursuant to Section 1013 of the Medicare Prescription Drug... summary, including the following elements: study number, study period, design, methodology, indication and... period, design, methodology, indication and diagnosis, proper use instructions, inclusion and exclusion...

Turbopump systems for liquid rocket engines

NASA Technical Reports Server (NTRS)

1974-01-01

The turbopump system, from preliminary design through rocket engine testing is examined. Selection of proper system type for each application and integration of the components into a working system are dealt with. Details are also given on the design of various components including inducers, pumps, turbines, gears, and bearings.

Evaluation of drainage pipe by field experimentation and supplemental laboratory experimentation : interim report No. 2.

DOT National Transportation Integrated Search

1978-03-01

Louisiana's Office of Highways reacts to a major problem when it attempts to shape and control drainage patterns along its right-of-ways. The Office's design engineers meet this challenge through proper section design and appropriate application of d...

Evaluation of drainage pipe by field experimentation and supplemental laboratory experimentation : interim report No. 1.

DOT National Transportation Integrated Search

1977-03-01

Louisiana's Office of Highways reacts to a major problem when it attempts to shape and control drainage patterns along its right-of-ways. The Office's design engineers meet this challenge through proper section design and appropriate application of d...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2010 CFR

2010-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2011 CFR

2011-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2013 CFR

2013-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2012 CFR

2012-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2014 CFR

2014-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

30 CFR 19.7 - Protection against explosion hazard.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion hazards..., if the lamp is designed and constructed to prevent the ignition of explosive mixtures of methane and...

30 CFR 19.7 - Protection against explosion hazard.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion hazards..., if the lamp is designed and constructed to prevent the ignition of explosive mixtures of methane and...

30 CFR 19.7 - Protection against explosion hazard.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion hazards..., if the lamp is designed and constructed to prevent the ignition of explosive mixtures of methane and...

30 CFR 19.7 - Protection against explosion hazard.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion hazards..., if the lamp is designed and constructed to prevent the ignition of explosive mixtures of methane and...

On-farm irrigatrion system design and operation

USDA-ARS?s Scientific Manuscript database

Most commercial blueberry fields are irrigated by overhead sprinklers or drip. Water is typically applied one to two times per week as needed with sprinklers, and every one to three days with drip. Sprinkler systems are relatively simple to install and maintain, and when designed properly, obtain re...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2014 CFR

2014-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2011 CFR

2011-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2012 CFR

2012-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2013 CFR

2013-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2010 CFR

2010-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2013 CFR

2013-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2011 CFR

2011-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2014 CFR

2014-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2012 CFR

2012-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

Locker-Room Talk.

ERIC Educational Resources Information Center

Lowe, Jason; Noyes, Brad

1999-01-01

Explains how proper athletic facility locker-room design can save time and money. Design factors that address who will be using the facility are discussed as are user requirements, such as preparation areas, total storage area per user, grooming area, and security areas. Final comments address maintenance and operations issues. (GR)

An MILP-based cross-layer optimization for a multi-reader arbitration in the UHF RFID system.

PubMed

Choi, Jinchul; Lee, Chaewoo

2011-01-01

In RFID systems, the performance of each reader such as interrogation range and tag recognition rate may suffer from interferences from other readers. Since the reader interference can be mitigated by output signal power control, spectral and/or temporal separation among readers, the system performance depends on how to adapt the various reader arbitration metrics such as time, frequency, and output power to the system environment. However, complexity and difficulty of the optimization problem increase with respect to the variety of the arbitration metrics. Thus, most proposals in previous study have been suggested to primarily prevent the reader collision with consideration of one or two arbitration metrics. In this paper, we propose a novel cross-layer optimization design based on the concept of combining time division, frequency division, and power control not only to solve the reader interference problem, but also to achieve the multiple objectives such as minimum interrogation delay, maximum reader utilization, and energy efficiency. Based on the priority of the multiple objectives, our cross-layer design optimizes the system sequentially by means of the mixed-integer linear programming. In spite of the multi-stage optimization, the optimization design is formulated as a concise single mathematical form by properly assigning a weight to each objective. Numerical results demonstrate the effectiveness of the proposed optimization design.

An MILP-Based Cross-Layer Optimization for a Multi-Reader Arbitration in the UHF RFID System

PubMed Central

Choi, Jinchul; Lee, Chaewoo

2011-01-01

In RFID systems, the performance of each reader such as interrogation range and tag recognition rate may suffer from interferences from other readers. Since the reader interference can be mitigated by output signal power control, spectral and/or temporal separation among readers, the system performance depends on how to adapt the various reader arbitration metrics such as time, frequency, and output power to the system environment. However, complexity and difficulty of the optimization problem increase with respect to the variety of the arbitration metrics. Thus, most proposals in previous study have been suggested to primarily prevent the reader collision with consideration of one or two arbitration metrics. In this paper, we propose a novel cross-layer optimization design based on the concept of combining time division, frequency division, and power control not only to solve the reader interference problem, but also to achieve the multiple objectives such as minimum interrogation delay, maximum reader utilization, and energy efficiency. Based on the priority of the multiple objectives, our cross-layer design optimizes the system sequentially by means of the mixed-integer linear programming. In spite of the multi-stage optimization, the optimization design is formulated as a concise single mathematical form by properly assigning a weight to each objective. Numerical results demonstrate the effectiveness of the proposed optimization design. PMID:22163743

Toolbox for the design of LiNbO3-based passive and active integrated quantum circuits

NASA Astrophysics Data System (ADS)

Sharapova, P. R.; Luo, K. H.; Herrmann, H.; Reichelt, M.; Meier, T.; Silberhorn, C.

2017-12-01

We present and discuss perspectives of current developments on advanced quantum optical circuits monolithically integrated in the lithium niobate platform. A set of basic components comprising photon pair sources based on parametric down conversion (PDC), passive routing elements and active electro-optically controllable switches and polarisation converters are building blocks of a toolbox which is the basis for a broad range of diverse quantum circuits. We review the state-of-the-art of these components and provide models that properly describe their performance in quantum circuits. As an example for applications of these models we discuss design issues for a circuit providing on-chip two-photon interference. The circuit comprises a PDC section for photon pair generation followed by an actively controllable modified mach-Zehnder structure for observing Hong-Ou-Mandel interference. The performance of such a chip is simulated theoretically by taking even imperfections of the properties of the individual components into account.

Early Warning System of Flood Disaster Based on Ultrasonic Sensors and Wireless Technology

NASA Astrophysics Data System (ADS)

Indrasari, W.; Iswanto, B. H.; Andayani, M.

2018-04-01

A flood disaster provides considerable losses to the people who live around the river. To mitigate losses of material due to flood disaster required an early warning system of flood disaster. For that reason, it necessary to design a system that provide alert to the people prior the flood disaster. And this paper describes development of a device for early detection system of flood disasters. This device consists of two ultrasonic sensors as a water level detector, and a water flow sensor as a water flow velocity sensor. The wireless technology and GSM is used as an information medium. The system is designed based on water level conditions in the Katulampa Dam, Bogor. Characterization of water level detector showed that the device effectively works in a range of water level of 14-250 cm, with a maximum relative error of 4.3%. Meanwhile the wireless works properly as far as 75 m, and the SMS transmission time is 8.20 second.

Phased-array sources based on nonlinear metamaterial nanocavities

DOE PAGES

Wolf, Omri; Campione, Salvatore; Benz, Alexander; ...

2015-07-01

Coherent superposition of light from subwavelength sources is an attractive prospect for the manipulation of the direction, shape and polarization of optical beams. This phenomenon constitutes the basis of phased arrays, commonly used at microwave and radio frequencies. Here we propose a new concept for phased-array sources at infrared frequencies based on metamaterial nanocavities coupled to a highly nonlinear semiconductor heterostructure. Optical pumping of the nanocavity induces a localized, phase-locked, nonlinear resonant polarization that acts as a source feed for a higher-order resonance of the nanocavity. Varying the nanocavity design enables the production of beams with arbitrary shape and polarization.more » As an example, we demonstrate two second harmonic phased-array sources that perform two optical functions at the second harmonic wavelength (~5 μm): a beam splitter and a polarizing beam splitter. As a result, proper design of the nanocavity and nonlinear heterostructure will enable such phased arrays to span most of the infrared spectrum.« less

Large motion high cycle high speed optical fibers for space based applications.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stromberg, Peter G.; Tandon, Rajan; Gibson, Cory S.

2014-10-01

Future remote sensing applications will require higher resolution and therefore higher data rates (up to perhaps 100 gigabits per second) while achieving lower mass and cost. A current limitation to the design space is high speed high bandwidth data does not cross movable gimbals because of cabling issues. This requires the detectors to be off gimbal. The ability to get data across the gimbal would open up efficiencies in designs where the detectors and the electronics can be placed anywhere on the system. Fiber optic cables provide light weight high speed high bandwidth connections. Current options are limited to 20,000more » cycles as opposed to the 1,000,000 cycles needed for future space based applications. To extend this to the million+ regime, requires a thorough understanding of the failure mechanisms and the materials, proper selection of materials (e.g., glass and jacket material) allowable geometry changes to the cable, radiation hardness, etc.« less

Implicit structured sequence learning: an fMRI study of the structural mere-exposure effect

PubMed Central

Folia, Vasiliki; Petersson, Karl Magnus

2014-01-01

In this event-related fMRI study we investigated the effect of 5 days of implicit acquisition on preference classification by means of an artificial grammar learning (AGL) paradigm based on the structural mere-exposure effect and preference classification using a simple right-linear unification grammar. This allowed us to investigate implicit AGL in a proper learning design by including baseline measurements prior to grammar exposure. After 5 days of implicit acquisition, the fMRI results showed activations in a network of brain regions including the inferior frontal (centered on BA 44/45) and the medial prefrontal regions (centered on BA 8/32). Importantly, and central to this study, the inclusion of a naive preference fMRI baseline measurement allowed us to conclude that these fMRI findings were the intrinsic outcomes of the learning process itself and not a reflection of a preexisting functionality recruited during classification, independent of acquisition. Support for the implicit nature of the knowledge utilized during preference classification on day 5 come from the fact that the basal ganglia, associated with implicit procedural learning, were activated during classification, while the medial temporal lobe system, associated with explicit declarative memory, was consistently deactivated. Thus, preference classification in combination with structural mere-exposure can be used to investigate structural sequence processing (syntax) in unsupervised AGL paradigms with proper learning designs. PMID:24550865

HiCAT Software Infrastructure: Safe hardware control with object oriented Python

NASA Astrophysics Data System (ADS)

Moriarty, Christopher; Brooks, Keira; Soummer, Remi

2018-01-01

High contrast imaging for Complex Aperture Telescopes (HiCAT) is a testbed designed to demonstrate coronagraphy and wavefront control for segmented on-axis space telescopes such as envisioned for LUVOIR. To limit the air movements in the testbed room, software interfaces for several different hardware components were developed to completely automate operations. When developing software interfaces for many different pieces of hardware, unhandled errors are commonplace and can prevent the software from properly closing a hardware resource. Some fragile components (e.g. deformable mirrors) can be permanently damaged because of this. We present an object oriented Python-based infrastructure to safely automate hardware control and optical experiments. Specifically, conducting high-contrast imaging experiments while monitoring humidity and power status along with graceful shutdown processes even for unexpected errors. Python contains a construct called a “context manager” that allows you define code to run when a resource is opened or closed. Context managers ensure that a resource is properly closed, even when unhandled errors occur. Harnessing the context manager design, we also use Python’s multiprocessing library to monitor humidity and power status without interrupting the experiment. Upon detecting a safety problem, the master process sends an event to the child process that triggers the context managers to gracefully close any open resources. This infrastructure allows us to queue up several experiments and safely operate the testbed without a human in the loop.

Implicit structured sequence learning: an fMRI study of the structural mere-exposure effect.

PubMed

Folia, Vasiliki; Petersson, Karl Magnus

2014-01-01

In this event-related fMRI study we investigated the effect of 5 days of implicit acquisition on preference classification by means of an artificial grammar learning (AGL) paradigm based on the structural mere-exposure effect and preference classification using a simple right-linear unification grammar. This allowed us to investigate implicit AGL in a proper learning design by including baseline measurements prior to grammar exposure. After 5 days of implicit acquisition, the fMRI results showed activations in a network of brain regions including the inferior frontal (centered on BA 44/45) and the medial prefrontal regions (centered on BA 8/32). Importantly, and central to this study, the inclusion of a naive preference fMRI baseline measurement allowed us to conclude that these fMRI findings were the intrinsic outcomes of the learning process itself and not a reflection of a preexisting functionality recruited during classification, independent of acquisition. Support for the implicit nature of the knowledge utilized during preference classification on day 5 come from the fact that the basal ganglia, associated with implicit procedural learning, were activated during classification, while the medial temporal lobe system, associated with explicit declarative memory, was consistently deactivated. Thus, preference classification in combination with structural mere-exposure can be used to investigate structural sequence processing (syntax) in unsupervised AGL paradigms with proper learning designs.

Underwater terrain-aided navigation system based on combination matching algorithm.

PubMed

Li, Peijuan; Sheng, Guoliang; Zhang, Xiaofei; Wu, Jingqiu; Xu, Baochun; Liu, Xing; Zhang, Yao

2018-07-01

Considering that the terrain-aided navigation (TAN) system based on iterated closest contour point (ICCP) algorithm diverges easily when the indicative track of strapdown inertial navigation system (SINS) is large, Kalman filter is adopted in the traditional ICCP algorithm, difference between matching result and SINS output is used as the measurement of Kalman filter, then the cumulative error of the SINS is corrected in time by filter feedback correction, and the indicative track used in ICCP is improved. The mathematic model of the autonomous underwater vehicle (AUV) integrated into the navigation system and the observation model of TAN is built. Proper matching point number is designated by comparing the simulation results of matching time and matching precision. Simulation experiments are carried out according to the ICCP algorithm and the mathematic model. It can be concluded from the simulation experiments that the navigation accuracy and stability are improved with the proposed combinational algorithm in case that proper matching point number is engaged. It will be shown that the integrated navigation system is effective in prohibiting the divergence of the indicative track and can meet the requirements of underwater, long-term and high precision of the navigation system for autonomous underwater vehicles. Copyright © 2017. Published by Elsevier Ltd.

Methods for accurate cold-chain temperature monitoring using digital data-logger thermometers

NASA Astrophysics Data System (ADS)

Chojnacky, M. J.; Miller, W. M.; Strouse, G. F.

2013-09-01

Complete and accurate records of vaccine temperature history are vital to preserving drug potency and patient safety. However, previously published vaccine storage and handling guidelines have failed to indicate a need for continuous temperature monitoring in vaccine storage refrigerators. We evaluated the performance of seven digital data logger models as candidates for continuous temperature monitoring of refrigerated vaccines, based on the following criteria: out-of-box performance and compliance with manufacturer accuracy specifications over the range of use; measurement stability over extended, continuous use; proper setup in a vaccine storage refrigerator so that measurements reflect liquid vaccine temperatures; and practical methods for end-user validation and establishing metrological traceability. Data loggers were tested using ice melting point checks and by comparison to calibrated thermocouples to characterize performance over 0 °C to 10 °C. We also monitored logger performance in a study designed to replicate the range of vaccine storage and environmental conditions encountered at provider offices. Based on the results of this study, the Centers for Disease Control released new guidelines on proper methods for storage, handling, and temperature monitoring of vaccines for participants in its federally-funded Vaccines for Children Program. Improved temperature monitoring practices will ultimately decrease waste from damaged vaccines, improve consumer confidence, and increase effective inoculation rates.

Programming standards for effective S-3D game development

NASA Astrophysics Data System (ADS)

Schneider, Neil; Matveev, Alexander

2008-02-01

When a video game is in development, more often than not it is being rendered in three dimensions - complete with volumetric depth. It's the PC monitor that is taking this three-dimensional information, and artificially displaying it in a flat, two-dimensional format. Stereoscopic drivers take the three-dimensional information captured from DirectX and OpenGL calls and properly display it with a unique left and right sided view for each eye so a proper stereoscopic 3D image can be seen by the gamer. The two-dimensional limitation of how information is displayed on screen has encouraged programming short-cuts and work-arounds that stifle this stereoscopic 3D effect, and the purpose of this guide is to outline techniques to get the best of both worlds. While the programming requirements do not significantly add to the game development time, following these guidelines will greatly enhance your customer's stereoscopic 3D experience, increase your likelihood of earning Meant to be Seen certification, and give you instant cost-free access to the industry's most valued consumer base. While this outline is mostly based on NVIDIA's programming guide and iZ3D resources, it is designed to work with all stereoscopic 3D hardware solutions and is not proprietary in any way.

Planning for hazardous campus waste collection.

PubMed

Liu, Kun-Hsing; Shih, Shao-Yang; Kao, Jehng-Jung

2011-05-15

This study examines a procedure developed for planning a nation-wide hazardous campus waste (HCW) collection system. Alternative HCW plans were designed for different collection frequencies, truckloads, storage limits, and also for establishing an additional transfer station. Two clustering methods were applied to group adjacent campuses into clusters based on their locations, HCW quantities, the type of vehicles used and collection frequencies. Transportation risk, storage risk, and collection cost are the major criteria used to evaluate the feasibility of each alternative. Transportation risk is determined based on the accident rates for each road type and collection distance, while storage risk is calculated by estimating the annual average HCW quantity stored on campus. Alternatives with large trucks can reduce both transportation risk and collection cost, but their storage risks would be significantly increased. Alternatives that collect neighboring campuses simultaneously can effectively reduce storage risks as well as collection cost if the minimum quantity to collect for each group of neighboring campuses can be properly set. The three transfer station alternatives evaluated for northern Taiwan are cost effective and involve significantly lower transportation risk. The procedure proposed is expected to facilitate decision making and to support analyses for formulating a proper nation-wide HCW collection plan. Copyright © 2011 Elsevier B.V. All rights reserved.

[Time based management in health care system: the chosen aspects].

PubMed

Kobza, Joanna; Syrkiewicz-Świtała, Magdalena

2014-01-01

Time-based management (TBM) is the key element of the whole management process. For many years in health care systems of highly developed countries modern and effective methods of time-based management have been implemented in both primary health care and hospitals (emergency departments and operating rooms). Over the past two decades a systematic review of Polish literature (since 1990) and peer reviewed articles published in international journals based on PubMed/Medline (2001-2011) have been carried out. The collected results indicate that the demographic and health changes in the populations are one of the main challenges facing general practitioners in the nearest future. Time-based management needs new and effective tools and skills, i.e., identification of priorities, well designed planning, delegation of the tasks, proper coordination, and creation of primary care teams that include additional members and human resources management. Proper reimbursement of health services, development of IT in health care system, better collection, storage, processing, analysis and exchange of information and research findings will also be needed. The use of innovative technologies, like telemedicine consultations, provides the possibility of reducing waiting time for diagnosis and treatment and in some cases could be applied in terms of secondary care. To improve the efficiency of operating rooms it is necessary to introduce different solutions, such as operating room coordinator involvement, application of automation to guide decision-making or use of robotic tools to assist surgical procedures. Overcrowded emergency departments have a major detrimental effect on the quality of hospital functions, therefore, efforts should be made to reduce them. Time-based management training among physicians and health care management in Poland, as well as the implementation of practice-based solutions still applied in highly developed countries seem to be necessary.

Fault tolerant control laws

NASA Technical Reports Server (NTRS)

Ly, U. L.; Ho, J. K.

1986-01-01

A systematic procedure for the synthesis of fault tolerant control laws to actuator failure has been presented. Two design methods were used to synthesize fault tolerant controllers: the conventional LQ design method and a direct feedback controller design method SANDY. The latter method is used primarily to streamline the full-state Q feedback design into a practical implementable output feedback controller structure. To achieve robustness to control actuator failure, the redundant surfaces are properly balanced according to their control effectiveness. A simple gain schedule based on the landing gear up/down logic involving only three gains was developed to handle three design flight conditions: Mach .25 and Mach .60 at 5000 ft and Mach .90 at 20,000 ft. The fault tolerant control law developed in this study provides good stability augmentation and performance for the relaxed static stability aircraft. The augmented aircraft responses are found to be invariant to the presence of a failure. Furthermore, single-loop stability margins of +6 dB in gain and +30 deg in phase were achieved along with -40 dB/decade rolloff at high frequency.