Hydrogen and Oxygen Gas Monitoring System Design and Operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee C. Cadwallader; Kevin G. DeWall; J. Stephen Herring

2007-06-01

This paper describes pertinent design practices of selecting types of monitors, monitor unit placement, setpoint selection, and maintenance considerations for gas monitors. While hydrogen gas monitors and enriched oxygen atmosphere monitors as they would be needed for hydrogen production experiments are the primary focus of this paper, monitors for carbon monoxide and carbon dioxide are also discussed. The experiences of designing, installing, and calibrating gas monitors for a laboratory where experiments in support of the DOE Nuclear Hydrogen Initiative (NHI) are described along with codes, standards, and regulations for these monitors. Information from the literature about best operating practices ismore » also presented. The NHI program has two types of activities. The first, near-term activity is laboratory and pilot-plant experimentation with different processes in the kilogram per day scale to select the most promising types of processes for future applications of hydrogen production. Prudent design calls for indoor gas monitors to sense any hydrogen leaks within these laboratory rooms. The second, longer-term activity is the prototype, or large-scale plants to produce tons of hydrogen per day. These large, outdoor production plants will require area (or “fencepost”) monitoring of hydrogen gas leaks. Some processes will have oxygen production with hydrogen production, and any oxygen releases are also safety concerns since oxygen gas is the strongest oxidizer. Monitoring of these gases is important for personnel safety of both indoor and outdoor experiments. There is some guidance available about proper placement of monitors. The fixed point, stationary monitor can only function if the intruding gas contacts the monitor. Therefore, monitor placement is vital to proper monitoring of the room or area. Factors in sensor location selection include: indoor or outdoor site, the location and nature of potential vapor/gas sources, chemical and physical data of the gases or vapors, liquids with volatility need sensors near the potential sources of release, nature and concentration of gas releases, natural and mechanical ventilation, detector installation locations not vulnerable to mechanical or water damage from normal operations, and locations that lend themselves to convenient maintenance and calibration. The guidance also states that sensors should be located in all areas where hazardous accumulations of gas may occur. Such areas might not be close to release points but might be areas with restricted air movement. Heavier than air gases are likely to accumulate in pits, trenches, drains, and other low areas. Lighter than air gases are more likely to accumulate in overhead spaces, above drop ceilings, etc. In general, sensors should be located close to any potential sources of major release of gas. The paper gives data on monitor sensitivity and expected lifetimes to support the monitor selection process. Proper selection of indoor and outdoor locations for monitors is described, accounting for the vapor densities of hydrogen and oxygen. The latest information on monitor alarm setpoint selection is presented. Typically, monitors require recalibration at least every six months, or more frequently for inhospitable locations, so ready access to the monitors is an important issue to consider in monitor siting. Gas monitors, depending on their type, can be susceptible to blockages of the detector element (i.e., dus« less

Delamination properity of 2060 aluminium lithium alloy laminate

NASA Astrophysics Data System (ADS)

Guo, Xiang; Huang, Yi; Tong, Dihua; Ma, Shaojun

2018-03-01

Delamination is an significant property of aluminium lithium alloy laminate for damage tolerance design. Double Crack Lap Shear specimens of "2/1" structure are used for testing delamination properity. Experiments of 2 stress ratio conditions R=0.06, 0.5 are conducted, and 5 stress levels for each stress ratio. Delamination growth data b-N are obtained from 4 crack tips’ locations. The energy release rate, Gd, of the "2/1" structure laminate are calculated. Alderliesten modelis used for describing delamination growth db/dN and energy release rate Gd. Parameters Cd and nd in Alderliesten model are determined for R=0.06 and R=0.5 by linear fitting. An analysis is made by comparing the results of different stress ratio conditons.

Reversible micromachining locator

DOEpatents

Salzer, Leander J.; Foreman, Larry R.

1999-01-01

This invention provides a device which includes a locator, a kinematic mount positioned on a conventional tooling machine, a part carrier disposed on the locator and a retainer ring. The locator has disposed therein a plurality of steel balls, placed in an equidistant position circumferentially around the locator. The kinematic mount includes a plurality of magnets which are in registry with the steel balls on the locator. In operation, a blank part to be machined is placed between a surface of a locator and the retainer ring (fitting within the part carrier). When the locator (with a blank part to be machined) is coupled to the kinematic mount, the part is thus exposed for the desired machining process. Because the locator is removably attachable to the kinematic mount, it can easily be removed from the mount, reversed, and reinserted onto the mount for additional machining. Further, the locator can likewise be removed from the mount and placed onto another tooling machine having a properly aligned kinematic mount. Because of the unique design and use of magnetic forces of the present invention, positioning errors of less than 0.25 micrometer for each machining process can be achieved.

An aerodynamic assessment of various supersonic fighter airplanes based on Soviet design concepts

NASA Technical Reports Server (NTRS)

Spearman, M. L.

1983-01-01

The aerodynamic, stability, and control characteristics of several supersonic fighter airplane concepts were assessed. The configurations include fixed-wing airplanes having delta wings, swept wings, and trapezoidal wings, and variable wing-sweep airplanes. Each concept employs aft tail controls. The concepts vary from lightweight, single engine, air superiority, point interceptor, or ground attack types to larger twin-engine interceptor and reconnaissance designs. Results indicate that careful application of the transonic or supersonic area rule can provide nearly optimum shaping for minimum drag for a specified Mach number requirement. Through the proper location of components and the exploitation of interference flow fields, the concepts provide linear pitching moment characteristics, high control effectiveness, and reasonably small variations in aerodynamic center location with a resulting high potential for maneuvering capability. By careful attention to component shaping and location and through the exploitation of local flow fields, favorable roll-to-yaw ratios may result and a high degree of directional stability can be achieved.

Development of high-efficiency solar cells on silicon web

NASA Technical Reports Server (NTRS)

Rohatgi, A.; Meier, D. L.; Campbell, R. B.; Seidensticker, R. G.; Rai-Choudhury, P.

1985-01-01

High-efficiency dendritic cells were discussed. The influence of twin planes and heat treatment on the location and effect of trace impurities was of particular interest. Proper heat treatment often increases efficiency by causing impurities to pile up at twin planes. Oxide passivation had a beneficial effect on efficiency. A very efficient antireflective (AR) coating of zinc selenide and magnesium fluoride was designed and fabricated. An aluminum back-surface reflector was also effective.

A Report Generator Volume 2

DTIC Science & Technology

1988-01-01

her Nicholle) ( korsakoffs (proper-noun singlp neuter) korsakoffs korekoffs) (huntingtons (proper-noun sing3p neuter) huntingtons huntingtons...hemisphere)) (sub-class (value gerstmann- syndrome 1-constructional-dyspraxia reading-coup aphasia)) (type (value lobe)) (dda (value (location...class)) (dda (value (function damage memory) (location brain))) (importance (value 10)) (damage (value 8))) ( korsakoffs (super-class (value stm)) (sub

Sensor Suitcase Tablet Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

The Retrocommissioning Sensor Suitcase is targeted for use in small commercial buildings of less than 50,000 square feet of floor space that regularly receive basic services such as maintenance and repair, but don't have in-house energy management staff or buildings experts. The Suitcase is designed to be easy-to-use by building maintenance staff, or other professionals such as telecom and alarm technicians. The software in the hand-held is designed to guide the staff to input the building and system information, deploy the sensors in proper location, configure the sensor hardware, and start the data collection.

Natural gas availability and ambient air quality in the Baton Rouge/New Orleans industrial complex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fieler, E.R.; Harrison, D.P.

1978-02-26

Three scenarios were modeled for the Baton Rouge/New Orleans area for 1985: one assumes the substitution of residual oil (0.7% sulfur) for gas to decrease gas-burning stationary sources from 80 to 8% and the use of properly designed stacks for large emitters; the second makes identical gas supply assumptions but adds proper stack dispersion for medium as well as large emitters; and the third is based on 16% gas-burning stationary sources. The Climatological Dispersion Model was used to translate (1974) emission rates into ambient air concentrations. Growth rates for residential, commercial, and transportation sources, but not industry, were considered. Themore » results show that proper policies, which would require not only tall stacks for large oil burning units (and for intermediate units also in the areas of high industrial concentration), but also the careful location of new plants would permit continued industrial expansion without severe air pollution problems.« less

Making a Back-Illuminated Imager with Back-Side Contact and Alignment Markers

NASA Technical Reports Server (NTRS)

Pain, Bedabrata

2008-01-01

A design modification and a fabrication process that implements the modification have been conceived to solve two problems encountered in the development of back-illuminated, back-sidethinned complementary metal oxide/ semiconductor (CMOS) image-detector integrated circuits. The two problems are (1) how to form metal electrical-contact pads on the back side that are electrically connected through the thickness in proper alignment with electrical contact points on the front side and (2) how to provide alignment keys on the back side to ensure proper registration of backside optical components (e.g., microlenses and/or color filters) with the front-side pixel pattern. The essence of the design modification is to add metal plugs that extend from the desired front-side locations through the thickness and protrude from the back side of the substrate. The plugs afford the required front-to-back electrical conduction, and the protrusions of the plugs serve as both the alignment keys and the bases upon which the back-side electrical-contact pads can be formed.

Economic competitiveness of fuel cell onsite integrated energy systems

NASA Technical Reports Server (NTRS)

Bollenbacher, G.

1983-01-01

The economic competitiveness of fuel cell onsite integrated energy systems (OS/IES) in residential and commercial buildings is examined. The analysis is carried out for three different buildings with each building assumed to be at three geographic locations spanning a range of climatic conditions. Numerous design options and operating strategies are evaluated and two economic criteria are used to measure economic performance. In general the results show that fuel cell OS/IES's are competitive in most regions of the country if the OS/IES is properly designed. The preferred design is grid connected, makes effective use of the fuel cell's thermal output, and has a fuel cell powerplant sized for the building's base electrical load.

Impact of Fire Ventilation on General Ventilation in the Building

NASA Astrophysics Data System (ADS)

Zender-Świercz, Ewa; Telejko, Marek

2017-10-01

The fire of building is a threat to its users. The biggest threat is generation, during lifetime of fire, hot gases and smoke. The purpose of quick and efficient evacuation from the area covered by the fire, at first step the escape routes have to be secured from smokiness. The smoke ventilation systems are used for this purpose. The proper design and execution of smoke ventilation is important not only because of the safety, but also of the maintenance of comfort in the building at a time when there is no fire. The manuscript presents the effect of incorrectly realized smoke ventilation in the stairwell of the medium building. The analysis shows that the flaps of smoke ventilation located in the stairwell may have a significant impact on the proper functioning of mechanical ventilation in the period when there is no fire. The improperly installed or incorrect insulated components cause perturbation of air flow and they change pressure distribution in the building. The conclusion of the analysis is the need to include the entire technical equipment of the building during the design and realization of its individual elements. The impact of various installations at each other is very important, and the omission of any of them can cause disturbances in the proper work of another.

Pilot Errors Involving Head-Up Displays (HUDs), Helmet-Mounted Displays (HMDs), and Night Vision Goggles (NVGs)

DTIC Science & Technology

1992-01-01

results in stimulation of spatial-motion-location visual processes, which are known to take precedence over any other sensor or cognitive stimuli. In...or version he is flying. This was initially an observation that stimulated the birth of the human-factors engineering discipline during World War H...collisions with the surface, the pilot needs inputs to sensory channels other than the focal visual system. Properly designed auditory and

Design of megawatt power level heat pipe reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mcclure, Patrick Ray; Poston, David Irvin; Dasari, Venkateswara Rao

An important niche for nuclear energy is the need for power at remote locations removed from a reliable electrical grid. Nuclear energy has potential applications at strategic defense locations, theaters of battle, remote communities, and emergency locations. With proper safeguards, a 1 to 10-MWe (megawatt electric) mobile reactor system could provide robust, self-contained, and long-term power in any environment. Heat pipe-cooled fast-spectrum nuclear reactors have been identified as a candidate for these applications. Heat pipe reactors, using alkali metal heat pipes, are perfectly suited for mobile applications because their nature is inherently simpler, smaller, and more reliable than “traditional” reactors.more » The goal of this project was to develop a scalable conceptual design for a compact reactor and to identify scaling issues for compact heat pipe cooled reactors in general. Toward this goal two detailed concepts were developed, the first concept with more conventional materials and a power of about 2 MWe and a the second concept with less conventional materials and a power level of about 5 MWe. A series of more qualitative advanced designs were developed (with less detail) that show power levels can be pushed to approximately 30 MWe.« less

Proper nozzle location, bit profile, and cutter arrangement affect PDC-bit performance significantly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garcia-Gavito, D.; Azar, J.J.

1994-09-01

During the past 20 years, the drilling industry has looked to new technology to halt the exponentially increasing costs of drilling oil, gas, and geothermal wells. This technology includes bit design innovations to improve overall drilling performance and reduce drilling costs. These innovations include development of drag bits that use PDC cutters, also called PDC bits, to drill long, continuous intervals of soft to medium-hard formations more economically than conventional three-cone roller-cone bits. The cost advantage is the result of higher rates of penetration (ROP's) and longer bit life obtained with the PDC bits. An experimental study comparing the effectsmore » of polycrystalline-diamond-compact (PDC)-bit design features on the dynamic pressure distribution at the bit/rock interface was conducted on a full-scale drilling rig. Results showed that nozzle location, bit profile, and cutter arrangement are significant factors in PDC-bit performance.« less

Reversible micromachining locator

DOEpatents

Salzer, L.J.; Foreman, L.R.

1999-08-31

This invention provides a device which includes a locator, a kinematic mount positioned on a conventional tooling machine, a part carrier disposed on the locator and a retainer ring. The locator has disposed therein a plurality of steel balls, placed in an equidistant position circumferentially around the locator. The kinematic mount includes a plurality of magnets which are in registry with the steel balls on the locator. In operation, a blank part to be machined is placed between a surface of a locator and the retainer ring (fitting within the part carrier). When the locator (with a blank part to be machined) is coupled to the kinematic mount, the part is thus exposed for the desired machining process. Because the locator is removably attachable to the kinematic mount, it can easily be removed from the mount, reversed, and reinserted onto the mount for additional machining. Further, the locator can likewise be removed from the mount and placed onto another tooling machine having a properly aligned kinematic mount. Because of the unique design and use of magnetic forces of the present invention, positioning errors of less than 0.25 micrometer for each machining process can be achieved. 7 figs.

Demonstration of the Attributes of Multi-increment Sampling and Proper Sample Processing Protocols for the Characterization of Metals on DoD Facilities

DTIC Science & Technology

2013-06-01

lenses of unconsolidated sand and rounded river gravel overlain by as much as 5 m of silt. Gravel consists mostly of quartz and metamorphic rock with...iii LIST OF FIGURES Page Figure 1. Example of multi-increment sampling using a systematic-random sampling design for collecting two separate...The small arms firing Range 16 Record berms at Fort Wainwright. .................... 25 Figure 9. Location of berms sampled using ISM and grab

20 CFR 658.415 - Transferring complaints to proper JS office.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Transferring complaints to proper JS office... Agency Js Complaint System § 658.415 Transferring complaints to proper JS office. (a) Where a JS-related... local office serving the area in which the employer is located. Where a JS-related complaint deals with...

Geographic information system-based healthcare waste management planning for treatment site location and optimal transportation routeing.

PubMed

Shanmugasundaram, Jothiganesh; Soulalay, Vongdeuane; Chettiyappan, Visvanathan

2012-06-01

In Lao People's Democratic Republic (Lao PDR), a growth of healthcare centres, and the environmental hazards and public health risks typically accompanying them, increased the need for healthcare waste (HCW) management planning. An effective planning of an HCW management system including components such as the treatment plant siting and an optimized routeing system for collection and transportation of waste is deemed important. National government offices at developing countries often lack the proper tools and methodologies because of the high costs usually associated with them. However, this study attempts to demonstrate the use of an inexpensive GIS modelling tool for healthcare waste management in the country. Two areas were designed for this study on HCW management, including: (a) locating centralized treatment plants and designing optimum travel routes for waste collection from nearby healthcare facilities; and (b) utilizing existing hospital incinerators and designing optimum routes for collecting waste from nearby healthcare facilities. Spatial analysis paved the way to understand the spatial distribution of healthcare wastes and to identify hotspots of higher waste generating locations. Optimal route models were designed for collecting and transporting HCW to treatment plants, which also highlights constraints in collecting and transporting waste for treatment and disposal. The proposed model can be used as a decision support tool for the efficient management of hospital wastes by government healthcare waste management authorities and hospitals.

Locating bomb factories by detecting hydrogen peroxide.

PubMed

Romolo, Francesco Saverio; Connell, Samantha; Ferrari, Carlotta; Suarez, Guillaume; Sauvain, Jean-Jacques; Hopf, Nancy B

2016-11-01

The analytical capability to detect hydrogen peroxide vapour can play a key role in localizing a site where a H2O2 based Improvised Explosive (IE) is manufactured. In security activities it is very important to obtain information in a short time. For this reason, an analytical method to be used in security activity needs portable devices. The authors have developed the first analytical method based on a portable luminometer, specifically designed and validated to locate IE manufacturing sites using quantitative on-site vapour analysis for H2O2. The method was tested both indoor and outdoor. The results demonstrate that the detection of H2O2 vapours could allow police forces to locate the site, while terrorists are preparing an attack. The collected data are also very important in developing new sensors, able to give an early alarm if located at a proper distance from a site where an H2O2 based IE is prepared. Copyright © 2016 Elsevier B.V. All rights reserved.

Analytic methods for design of wave cycles for wave rotor core engines

NASA Technical Reports Server (NTRS)

Resler, Edwin L., Jr.; Mocsari, Jeffrey C.; Nalim, M. R.

1993-01-01

A procedure to design a preliminary wave rotor cycle for any application is presented. To complete a cycle with heat addition there are two separate but related design steps that must be followed. The 'wave' boundary conditions determine the allowable amount of heat added in any case and the ensuing wave pattern requires certain pressure discharge conditions to allow the process to be made cyclic. This procedure, when applied, gives a first estimate of the cycle performance and the necessary information for the next step in the design process, namely the application of a characteristic based or other appropriate detailed one dimensional wave calculation that locates the proper porting around the periphery of the wave rotor. Four examples of the design procedure are given to demonstrate its utility and generality. These examples also illustrate the large gains in performance that could be realized with the use of wave rotor enhanced propulsion cycles.

Multi-frequency entanglement router system

NASA Astrophysics Data System (ADS)

Erdmann, Reinhard; Hughes, David

2017-05-01

A high performance free-space Wavelength Division Multiplexed (WDM) transceiver system is assessed as to its viability for routing collinear entangled photons in place of the classical optical signals for which it was designed. Explicit calculations demonstrate that entanglement in the input state is retained through transit of the system without intrinsic loss. Introducing spatial degrees of freedom changed the entanglement so that it could be manifested at remote locations, as required in non-local Bell test measurements or Quantum Key Distribution (QKD) Protocols. It was also found that by adding proper components, the exit state could be changed from being frequency entangled to polarization entangled, with respect to the (remote) paths of the photons. Finally it was found possible to route a complete entangled state to either of the two remote users by proper selection of the discrete frequencies in the input state. Each entanglement in the photon states was maximal, hence suited for Quantum Information Processing (QIP) applications.

Pressure investigation of NASA leading edge vortex flaps on a 60 deg Delta wing

NASA Technical Reports Server (NTRS)

Marchman, J. F., III; Donatelli, D. A.; Terry, J. E.

1983-01-01

Pressure distributions on a 60 deg Delta Wing with NASA designed leading edge vortex flaps (LEVF) were found in order to provide more pressure data for LEVF and to help verify NASA computer codes used in designing these flaps. These flaps were intended to be optimized designs based on these computer codes. However, the pressure distributions show that the flaps wre not optimum for the size and deflection specified. A second drag-producing vortex forming over the wing indicated that the flap was too large for the specified deflection. Also, it became apparent that flap thickness has a possible effect on the reattachment location of the vortex. Research is continuing to determine proper flap size and deflection relationships that provide well-behaved flowfields and acceptable hinge-moment characteristics.

16 CFR 1512.19 - Instructions and labeling.

Code of Federal Regulations, 2010 CFR

2010-01-01

... road operation. (2) Assembly instructions for accomplishing complete and proper assembly. (3) Maintenance instructions for proper maintenance of brakes, control cables, bearing adjustments, wheel... determine that such maintenance is beyond the capability of the consumer, specifics regarding locations...

A Compton scattering setup for pulse shape discrimination studies in germanium detectors.

PubMed

von Sturm, K; Belogurov, S; Brugnera, R; Garfagnini, A; Lippi, I; Modenese, L; Rosso, D; Turcato, M

2017-07-01

Pulse shape discrimination is an important handle to improve sensitivity in low background experiments. A dedicated setup was built to investigate the response of high-purity germanium detectors to single Compton scattered events. Using properly collimated γ-ray sources, it is possible to select events with known interaction location. The aim is to correlate the position dependent signal shape with geometrical and electrical properties of the detector. We report on design and performance of the setup with a first look on data. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaluation of knee joint forces during kneeling work with different kneepads.

PubMed

Xu, Hang; Jampala, Sree; Bloswick, Donald; Zhao, Jie; Merryweather, Andrew

2017-01-01

The main purpose of this study is to determine knee joint forces resulting from kneeling work with and without kneepads to quantify how different kneepads redistribute force. Eleven healthy males simulated a tile setting task to different locations during six kneepad states (five different kneepad types and without kneepad). Peak and average forces on the anatomical landmarks of both knees were obtained by custom force sensors. The results revealed that kneepad design can significantly modify the forces on the knee joint through redistribution. The Professional Gel design was preferred among the five tested kneepads which was confirmed with both force measurements and participants' responses. The extreme reaching locations induced significantly higher joint forces on left knee or right knee depending on task. The conclusion of this study is that a properly selected kneepad for specific tasks and a more neutral working posture can modify the force distribution on the knees and likely decrease the risk of knee disorders from kneeling work. Copyright © 2016 Elsevier Ltd. All rights reserved.

Magnetic surveys for locating abandoned wells

USGS Publications Warehouse

,

1995-01-01

Abandoned and unrecorded wells may act as conduits for the contamination of groundwater supplies by oil field brines and other pollutants. The casings of abandoned wells eventually develop leaks, which, if not properly plugged, can allow pollutants to reach freshwater aquifers that supply drinking water. Sources of pollutants include brine ponds, landfill sites, agricultural activities, industrial activities, illegal disposal sites, or accidental spills. The problem is particularly acute in regions where there are old petroleum fields or where water wells have been extensively used for agricultural irrigation. Even urban areas can contain wells that were abandoned and concealed during development. Carefully designed ground magnetic or aeromagnetic surveys can be used to locate abandoned wells by mapping the magnetic disturbances or "anomalies" produced by their steel well casings. The U.S. Geological Survey (USGS) can, at the request of other Federal, State, or local agencies, conduct, process, and interpret such surveys, or it can aid in the design and monitoring of contracts for such surveys.

Frequency wavenumber design of spiral macro fiber composite directional transducers

NASA Astrophysics Data System (ADS)

Carrara, Matteo; Ruzzene, Massimo

2015-04-01

This work is focused on design and testing of a novel class of transducers for Structural Health Monitoring (SHM), able to perform directional interrogation of plate-like structures. These transducers leverage guided waves (GWs), and in particular Lamb waves, that have emerged as a very prominent option for assessing the state of a structure during operation. GW-SHM approaches greatly benefit from the use of transducers with controllable directional characteristics, so that selective scanning of a surface can be performed to locate damage, impacts, or cracks. In the concepts that we propose, continuous beam steering and directional actuation are achieved through proper selection of the excitation frequency. The design procedure takes advantage of the wavenumber representation of the device, and formulates the problem using a Fourier-based approach. The active layer of the transducer is made of piezoelectric fibers embedded into an epoxy matrix, allowing the device to be flexible, and thus suitable for application on non{ at surfaces. Proper shaping of the electrodes pattern through a compensation function allows taking into account the anisotropy level introduced by the active layer. The resulting spiral frequency steerable acoustic actuator is a configuration that features (i) enhanced performance, (ii) reduced complexity, and (iii) reduced hardware requirements of such devices.

41 CFR 102-74.340 - Who is responsible for monitoring and controlling areas designated for smoking by an agency head...

Code of Federal Regulations, 2010 CFR

2010-07-01

... with proper signage? 102-74.340 Section 102-74.340 Public Contracts and Property Management Federal... designated for smoking by an agency head and for identifying those areas with proper signage? Agency heads... smoking and identifying these areas with proper signage. Suitable, uniform signs reading “Designated...

41 CFR 102-74.340 - Who is responsible for monitoring and controlling areas designated for smoking by an agency head...

Code of Federal Regulations, 2011 CFR

2011-01-01

... with proper signage? 102-74.340 Section 102-74.340 Public Contracts and Property Management Federal... designated for smoking by an agency head and for identifying those areas with proper signage? Agency heads... smoking and identifying these areas with proper signage. Suitable, uniform signs reading “Designated...

41 CFR 102-74.340 - Who is responsible for monitoring and controlling areas designated for smoking by an agency head...

Code of Federal Regulations, 2013 CFR

2013-07-01

... with proper signage? 102-74.340 Section 102-74.340 Public Contracts and Property Management Federal... designated for smoking by an agency head and for identifying those areas with proper signage? Agency heads... smoking and identifying these areas with proper signage. Suitable, uniform signs reading “Designated...

41 CFR 102-74.340 - Who is responsible for monitoring and controlling areas designated for smoking by an agency head...

Code of Federal Regulations, 2014 CFR

2014-01-01

... with proper signage? 102-74.340 Section 102-74.340 Public Contracts and Property Management Federal... designated for smoking by an agency head and for identifying those areas with proper signage? Agency heads... smoking and identifying these areas with proper signage. Suitable, uniform signs reading “Designated...

41 CFR 102-74.340 - Who is responsible for monitoring and controlling areas designated for smoking by an agency head...

Code of Federal Regulations, 2012 CFR

2012-01-01

... with proper signage? 102-74.340 Section 102-74.340 Public Contracts and Property Management Federal... designated for smoking by an agency head and for identifying those areas with proper signage? Agency heads... smoking and identifying these areas with proper signage. Suitable, uniform signs reading “Designated...

Experimental Design for Estimating Unknown Hydraulic Conductivity in a Confined Aquifer using a Genetic Algorithm and a Reduced Order Model

NASA Astrophysics Data System (ADS)

Ushijima, T.; Yeh, W.

2013-12-01

An optimal experimental design algorithm is developed to select locations for a network of observation wells that provides the maximum information about unknown hydraulic conductivity in a confined, anisotropic aquifer. The design employs a maximal information criterion that chooses, among competing designs, the design that maximizes the sum of squared sensitivities while conforming to specified design constraints. Because that the formulated problem is non-convex and contains integer variables (necessitating a combinatorial search), for a realistically-scaled model, the problem may be difficult, if not impossible, to solve through traditional mathematical programming techniques. Genetic Algorithms (GAs) are designed to search out the global optimum; however because a GA requires a large number of calls to a groundwater model, the formulated optimization problem may still be infeasible to solve. To overcome this, Proper Orthogonal Decomposition (POD) is applied to the groundwater model to reduce its dimension. The information matrix in the full model space can then be searched without solving the full model.

49 CFR 234.201 - Location of plans.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Location of plans. 234.201 Section 234.201..., Inspection, and Testing Maintenance Standards § 234.201 Location of plans. Plans required for proper maintenance and testing shall be kept at each highway-rail grade crossing warning system location. Plans shall...

Impurity-doped optical shock, detonation and damage location sensor

DOEpatents

Weiss, J.D.

1995-02-07

A shock, detonation, and damage location sensor providing continuous fiber-optic means of measuring shock speed and damage location, and could be designed through proper cabling to have virtually any desired crush pressure. The sensor has one or a plurality of parallel multimode optical fibers, or a singlemode fiber core, surrounded by an elongated cladding, doped along their entire length with impurities to fluoresce in response to light at a different wavelength entering one end of the fiber(s). The length of a fiber would be continuously shorted as it is progressively destroyed by a shock wave traveling parallel to its axis. The resulting backscattered and shifted light would eventually enter a detector and be converted into a proportional electrical signals which would be evaluated to determine shock velocity and damage location. The corresponding reduction in output, because of the shortening of the optical fibers, is used as it is received to determine the velocity and position of the shock front as a function of time. As a damage location sensor the sensor fiber cracks along with the structure to which it is mounted. The size of the resulting drop in detector output is indicative of the location of the crack. 8 figs.

Impurity-doped optical shock, detonation and damage location sensor

DOEpatents

Weiss, Jonathan D.

1995-01-01

A shock, detonation, and damage location sensor providing continuous fiber-optic means of measuring shock speed and damage location, and could be designed through proper cabling to have virtually any desired crush pressure. The sensor has one or a plurality of parallel multimode optical fibers, or a singlemode fiber core, surrounded by an elongated cladding, doped along their entire length with impurities to fluoresce in response to light at a different wavelength entering one end of the fiber(s). The length of a fiber would be continuously shorted as it is progressively destroyed by a shock wave traveling parallel to its axis. The resulting backscattered and shifted light would eventually enter a detector and be converted into a proportional electrical signals which would be evaluated to determine shock velocity and damage location. The corresponding reduction in output, because of the shortening of the optical fibers, is used as it is received to determine the velocity and position of the shock front as a function of time. As a damage location sensor the sensor fiber cracks along with the structure to which it is mounted. The size of the resulting drop in detector output is indicative of the location of the crack.

Diatomite filtration of water for injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olmsted, B.C. Jr.; Bell, G.R.

1966-01-01

A discussion is presented of the capabilities, problems, and answers, in the performance of diatomite filters. The discussion includes a description of diatomite filtration, new developments, design criteria, and some case histories. Diatomite filters, when properly designed and installed, and when properly applied, can provide effective clarification of waters for injection at low capital and operating costs. Design, installation, and proper application, effectiveness, and capital and operating costs can be placed in the proper perspective in the light of general experience and recent pilot plant tests in the southern California area. (30 refs.)

The Commander’s Emergency Response Program: A Model for Future Implementation

DTIC Science & Technology

2010-04-07

unintended Effects. The INVEST-E methodology serves as a tool for commanders and their designated practitioners to properly select projects, increasing...for commanders and their designated practitioners to properly select projects, increasing the effectiveness of CERP funds. 4 TABLE OF...and unintended Effects. The INVEST-E methodology serves as a tool for commanders and their designated practitioners to properly select projects

Design of helicopter rotor blades for optimum dynamic characteristics

NASA Technical Reports Server (NTRS)

Peters, D. A.; Ko, T.; Korn, A. E.; Rossow, M. P.

1982-01-01

The possibilities and the limitations of tailoring blade mass and stiffness distributions to give an optimum blade design in terms of weight, inertia, and dynamic characteristics are investigated. Changes in mass or stiffness distribution used to place rotor frequencies at desired locations are determined. Theoretical limits to the amount of frequency shift are established. Realistic constraints on blade properties based on weight, mass moment of inertia size, strength, and stability are formulated. The extent hub loads can be minimized by proper choice of EL distribution is determined. Configurations that are simple enough to yield clear, fundamental insights into the structural mechanisms but which are sufficiently complex to result in a realistic result for an optimum rotor blade are emphasized.

Application of zonal model on indoor air sensor network design

NASA Astrophysics Data System (ADS)

Chen, Y. Lisa; Wen, Jin

2007-04-01

Growing concerns over the safety of the indoor environment have made the use of sensors ubiquitous. Sensors that detect chemical and biological warfare agents can offer early warning of dangerous contaminants. However, current sensor system design is more informed by intuition and experience rather by systematic design. To develop a sensor system design methodology, a proper indoor airflow modeling approach is needed. Various indoor airflow modeling techniques, from complicated computational fluid dynamics approaches to simplified multi-zone approaches, exist in the literature. In this study, the effects of two airflow modeling techniques, multi-zone modeling technique and zonal modeling technique, on indoor air protection sensor system design are discussed. Common building attack scenarios, using a typical CBW agent, are simulated. Both multi-zone and zonal models are used to predict airflows and contaminant dispersion. Genetic Algorithm is then applied to optimize the sensor location and quantity. Differences in the sensor system design resulting from the two airflow models are discussed for a typical office environment and a large hall environment.

Hydraulic head estimation at unobserved locations: Approximating the distribution of the absolute error based on geologic interpretations

NASA Astrophysics Data System (ADS)

Langousis, Andreas; Kaleris, Vassilios; Xeygeni, Vagia; Magkou, Foteini

2017-04-01

Assessing the availability of groundwater reserves at a regional level, requires accurate and robust hydraulic head estimation at multiple locations of an aquifer. To that extent, one needs groundwater observation networks that can provide sufficient information to estimate the hydraulic head at unobserved locations. The density of such networks is largely influenced by the spatial distribution of the hydraulic conductivity in the aquifer, and it is usually determined through trial-and-error, by solving the groundwater flow based on a properly selected set of alternative but physically plausible geologic structures. In this work, we use: 1) dimensional analysis, and b) a pulse-based stochastic model for simulation of synthetic aquifer structures, to calculate the distribution of the absolute error in hydraulic head estimation as a function of the standardized distance from the nearest measuring locations. The resulting distributions are proved to encompass all possible small-scale structural dependencies, exhibiting characteristics (bounds, multi-modal features etc.) that can be explained using simple geometric arguments. The obtained results are promising, pointing towards the direction of establishing design criteria based on large-scale geologic maps.

Optimal design of a beam-based dynamic vibration absorber using fixed-points theory

NASA Astrophysics Data System (ADS)

Hua, Yingyu; Wong, Waion; Cheng, Li

2018-05-01

The addition of a dynamic vibration absorber (DVA) to a vibrating structure could provide an economic solution for vibration suppressions if the absorber is properly designed and located onto the structure. A common design of the DVA is a sprung mass because of its simple structure and low cost. However, the vibration suppression performance of this kind of DVA is limited by the ratio between the absorber mass and the mass of the primary structure. In this paper, a beam-based DVA (beam DVA) is proposed and optimized for minimizing the resonant vibration of a general structure. The vibration suppression performance of the proposed beam DVA depends on the mass ratio, the flexural rigidity and length of the beam. In comparison with the traditional sprung mass DVA, the proposed beam DVA shows more flexibility in vibration control design because it has more design parameters. With proper design, the beam DVA's vibration suppression capability can outperform that of the traditional DVA under the same mass constraint. The general approach is illustrated using a benchmark cantilever beam as an example. The receptance theory is introduced to model the compound system consisting of the host beam and the attached beam-based DVA. The model is validated through comparisons with the results from Abaqus as well as the Transfer Matrix method (TMM) method. Fixed-points theory is then employed to derive the analytical expressions for the optimum tuning ratio and damping ratio of the proposed beam absorber. A design guideline is then presented to choose the parameters of the beam absorber. Comparisons are finally presented between the beam absorber and the traditional DVA in terms of the vibration suppression effect. It is shown that the proposed beam absorber can outperform the traditional DVA by following this proposed guideline.

Computational fluid dynamics modeling and analysis for the Giant Magellan Telescope (GMT)

NASA Astrophysics Data System (ADS)

Ladd, John; Slotnick, Jeffrey; Norby, William; Bigelow, Bruce; Burgett, William

2016-08-01

The Giant Magellan Telescope (GMT) is planned for construction at a summit of Cerro Las Campanas at the Los Campanas Observatory (LCO) in Chile. GMT will be the most powerful ground-based telescope in operation in the world. Aero-thermal interactions between the site topography, enclosure, internal systems, and optics are complex. A key parameter for optical quality is the thermal gradient between the terrain and the air entering the enclosure, and how quickly that gradient can be dissipated to equilibrium. To ensure the highest quality optical performance, careful design of the telescope enclosure building, location of the enclosure on the summit, and proper venting of the airflow within the enclosure is essential to minimize the impact of velocity and temperature gradients in the air entering the enclosure. High-fidelity Reynolds-Averaged Navier Stokes (RANS) Computational Fluid Dynamics (CFD) analysis of the GMT, enclosure, and LCO terrain is performed to study (a) the impact of either an open or closed enclosure base soffit external shape design, (b) the effect of telescope/enclosure location on the mountain summit, and (c) the effect of enclosure venting patterns. Details on the geometry modeling, grid discretization, and flow solution are first described. Then selected computational results are shown to quantify the quality of the airflow entering the GMT enclosure based on soffit, site location, and venting considerations. Based on the results, conclusions are provided on GMT soffit design, site location, and enclosure venting. The current work is not used to estimate image quality but will be addressed in future analyses as described in the conclusions.

A model for distribution centers location-routing problem on a multimodal transportation network with a meta-heuristic solving approach

NASA Astrophysics Data System (ADS)

Fazayeli, Saeed; Eydi, Alireza; Kamalabadi, Isa Nakhai

2017-07-01

Nowadays, organizations have to compete with different competitors in regional, national and international levels, so they have to improve their competition capabilities to survive against competitors. Undertaking activities on a global scale requires a proper distribution system which could take advantages of different transportation modes. Accordingly, the present paper addresses a location-routing problem on multimodal transportation network. The introduced problem follows four objectives simultaneously which form main contribution of the paper; determining multimodal routes between supplier and distribution centers, locating mode changing facilities, locating distribution centers, and determining product delivery tours from the distribution centers to retailers. An integer linear programming is presented for the problem, and a genetic algorithm with a new chromosome structure proposed to solve the problem. Proposed chromosome structure consists of two different parts for multimodal transportation and location-routing parts of the model. Based on published data in the literature, two numerical cases with different sizes generated and solved. Also, different cost scenarios designed to better analyze model and algorithm performance. Results show that algorithm can effectively solve large-size problems within a reasonable time which GAMS software failed to reach an optimal solution even within much longer times.

A model for distribution centers location-routing problem on a multimodal transportation network with a meta-heuristic solving approach

NASA Astrophysics Data System (ADS)

Fazayeli, Saeed; Eydi, Alireza; Kamalabadi, Isa Nakhai

2018-07-01

Nowadays, organizations have to compete with different competitors in regional, national and international levels, so they have to improve their competition capabilities to survive against competitors. Undertaking activities on a global scale requires a proper distribution system which could take advantages of different transportation modes. Accordingly, the present paper addresses a location-routing problem on multimodal transportation network. The introduced problem follows four objectives simultaneously which form main contribution of the paper; determining multimodal routes between supplier and distribution centers, locating mode changing facilities, locating distribution centers, and determining product delivery tours from the distribution centers to retailers. An integer linear programming is presented for the problem, and a genetic algorithm with a new chromosome structure proposed to solve the problem. Proposed chromosome structure consists of two different parts for multimodal transportation and location-routing parts of the model. Based on published data in the literature, two numerical cases with different sizes generated and solved. Also, different cost scenarios designed to better analyze model and algorithm performance. Results show that algorithm can effectively solve large-size problems within a reasonable time which GAMS software failed to reach an optimal solution even within much longer times.

Repair, Evaluation, Maintenance, and Rehabilitation Research Program. Lubricants for Hydraulic Structures

DTIC Science & Technology

1989-08-01

machinery design , precision machining, proper maintenance, and proper lubrication. Ordinarily, wear is thought of only in terms of abrasive wear occurring in...operate under this principle. However, the design must allow the plates to lift and tilt properly and provide sufficient area to lift the load. 38. Another...friction and wear to a minimum. Boundary Lubrication 42. Lubrication designed to protect against frictional effects when asperities meet is called

7. View (looking west) of the second floor corridor in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. View (looking west) of the second floor corridor in the south segment of building. The second floor was designed for residential rental rooms. The guardrail, balusters, newel posts, and handrail, as well as the two upper-level door openings with transoms, are original features. The doors, proper, are nonoriginal and probably were installed when the second floor was converted to office use. The pair of doors (one leaf is open and one is closed) is located at the intermediate stair landing. The original exterior doorway (without a door) is located at the bottom of the stair. The upper-level door without a transom is nonoriginal, as are the floor tile and wall paneling. At the time of documentation a suspended ceiling and duct were removed to ... - Stroud Building, 31-33 North Central Avenue, Phoenix, Maricopa County, AZ

THE EXPERIENCE IN THE UNITED STATES WITH REACTOR OPERATION AND REACTOR SAFEGUARDS

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCullough, C.R.

1958-10-31

Reactors are operating or planned at locations in the United States in cities, near cities, and at remote locations. There is a general pattern that the higher power reactors are not in, but fairly uear cities, and the testing reactors for more hazardous experiments are at remote locations. A great deal has been done on the theoretical and experimental study of importunt features of reactor design. The metal-water reaction is still a theoretical possibility but tests of fuel element burnout under conditions approaching reactor operation gave no reaction. It appears that nucleate boiling does not necessarily result in steam blanketingmore » and fuel melting. Much attention is being given to the calculation of core kinetics but it is being found that temperature, power, and void coefficients cannot be calculated with accuracy and experiments are required. Some surprises are found giving positive localized void coefficients. Possible oscillatory behavior of reactors is being given careful study. No dangerous oscillations have been found in operating reactors but osciliations hare appeared in experimeats. The design of control and safety systems varies wvith different constructors. The relation of control to the kinetic behavior of the reactor is being studied. The importance of sensing element locations in order to know actual local reactor power level is being recognized. The time constants of instrumentation as related to reactor kinetics are being studied. Pressure vessels for reactors are being designed and manufactured. Many of these are beyond any previous experience. The stress problem is being given careful study. The effect of radiation is being studied experimentally. The stress problems of piping and pressure vessels is a difficult design problem being met successfully in reactor plants. The proper organization and procedure for operation of reactors is being evolved for resourch, testing, and power reactors. The importance of written standards and instructions for both normal and abnormal operating conditions is recogmized. Corfinement of radioactive materials either by tight steel shells, tight buildings, or semi-tight structures vented through filters is considered necessary in the United States. A discussion will be given of specifications, construction, and testing of these structures. The need for emergency plans has been stressed by recent experiences in radioactive releases. The problems of such plans to cover all grades of accidents will be discussed. The theoretical consequences of releases of radioactive materials have been studied and these results will be compared with actual experience. The problem of exposures from normal and abnormal operetion of reactors is a problem of desiga and operation on one hand and the amount of damage to be expected on the other. The safeguard problem is closely related to the acceptable doses of radiouctivity which the ICRP recommend. The future of atomic energy depends upon adequate safeguards and economical design and operation. Accepted criteria are required to guide designers as to the proper balance of caution and boldness. (auth)« less

Improving Kinematic Accuracy of Soft Wearable Data Gloves by Optimizing Sensor Locations

PubMed Central

Kim, Dong Hyun; Lee, Sang Wook; Park, Hyung-Soon

2016-01-01

Bending sensors enable compact, wearable designs when used for measuring hand configurations in data gloves. While existing data gloves can accurately measure angular displacement of the finger and distal thumb joints, accurate measurement of thumb carpometacarpal (CMC) joint movements remains challenging due to crosstalk between the multi-sensor outputs required to measure the degrees of freedom (DOF). To properly measure CMC-joint configurations, sensor locations that minimize sensor crosstalk must be identified. This paper presents a novel approach to identifying optimal sensor locations. Three-dimensional hand surface data from ten subjects was collected in multiple thumb postures with varied CMC-joint flexion and abduction angles. For each posture, scanned CMC-joint contours were used to estimate CMC-joint flexion and abduction angles by varying the positions and orientations of two bending sensors. Optimal sensor locations were estimated by the least squares method, which minimized the difference between the true CMC-joint angles and the joint angle estimates. Finally, the resultant optimal sensor locations were experimentally validated. Placing sensors at the optimal locations, CMC-joint angle measurement accuracies improved (flexion, 2.8° ± 1.9°; abduction, 1.9° ± 1.2°). The proposed method for improving the accuracy of the sensing system can be extended to other types of soft wearable measurement devices. PMID:27240364

Sampling designs for HIV molecular epidemiology with application to Honduras.

PubMed

Shepherd, Bryan E; Rossini, Anthony J; Soto, Ramon Jeremias; De Rivera, Ivette Lorenzana; Mullins, James I

2005-11-01

Proper sampling is essential to characterize the molecular epidemiology of human immunodeficiency virus (HIV). HIV sampling frames are difficult to identify, so most studies use convenience samples. We discuss statistically valid and feasible sampling techniques that overcome some of the potential for bias due to convenience sampling and ensure better representation of the study population. We employ a sampling design called stratified cluster sampling. This first divides the population into geographical and/or social strata. Within each stratum, a population of clusters is chosen from groups, locations, or facilities where HIV-positive individuals might be found. Some clusters are randomly selected within strata and individuals are randomly selected within clusters. Variation and cost help determine the number of clusters and the number of individuals within clusters that are to be sampled. We illustrate the approach through a study designed to survey the heterogeneity of subtype B strains in Honduras.

Earthquake Damping Device for Steel Frame

NASA Astrophysics Data System (ADS)

Zamri Ramli, Mohd; Delfy, Dezoura; Adnan, Azlan; Torman, Zaida

2018-04-01

Structures such as buildings, bridges and towers are prone to collapse when natural phenomena like earthquake occurred. Therefore, many design codes are reviewed and new technologies are introduced to resist earthquake energy especially on building to avoid collapse. The tuned mass damper is one of the earthquake reduction products introduced on structures to minimise the earthquake effect. This study aims to analyse the effectiveness of tuned mass damper by experimental works and finite element modelling. The comparisons are made between these two models under harmonic excitation. Based on the result, it is proven that installing tuned mass damper will reduce the dynamic response of the frame but only in several input frequencies. At the highest input frequency applied, the tuned mass damper failed to reduce the responses. In conclusion, in order to use a proper design of damper, detailed analysis must be carried out to have sufficient design based on the location of the structures with specific ground accelerations.

Development of Tripropellant CFD Design Code

NASA Technical Reports Server (NTRS)

Farmer, Richard C.; Cheng, Gary C.; Anderson, Peter G.

1998-01-01

A tripropellant, such as GO2/H2/RP-1, CFD design code has been developed to predict the local mixing of multiple propellant streams as they are injected into a rocket motor. The code utilizes real fluid properties to account for the mixing and finite-rate combustion processes which occur near an injector faceplate, thus the analysis serves as a multi-phase homogeneous spray combustion model. Proper accounting of the combustion allows accurate gas-side temperature predictions which are essential for accurate wall heating analyses. The complex secondary flows which are predicted to occur near a faceplate cannot be quantitatively predicted by less accurate methodology. Test cases have been simulated to describe an axisymmetric tripropellant coaxial injector and a 3-dimensional RP-1/LO2 impinger injector system. The analysis has been shown to realistically describe such injector combustion flowfields. The code is also valuable to design meaningful future experiments by determining the critical location and type of measurements needed.

Automatic Optimization of Wayfinding Design.

PubMed

Huang, Haikun; Lin, Ni-Ching; Barrett, Lorenzo; Springer, Darian; Wang, Hsueh-Cheng; Pomplun, Marc; Yu, Lap-Fai

2017-10-10

Wayfinding signs play an important role in guiding users to navigate in a virtual environment and in helping pedestrians to find their ways in a real-world architectural site. Conventionally, the wayfinding design of a virtual environment is created manually, so as the wayfinding design of a real-world architectural site. The many possible navigation scenarios, and the interplay between signs and human navigation, can make the manual design process overwhelming and non-trivial. As a result, creating a wayfinding design for a typical layout can take months to several years. In this paper, we introduce the Way to Go! approach for automatically generating a wayfinding design for a given layout. The designer simply has to specify some navigation scenarios; our approach will automatically generate an optimized wayfinding design with signs properly placed considering human agents' visibility and possibility of making navigation mistakes. We demonstrate the effectiveness of our approach in generating wayfinding designs for different layouts. We evaluate our results by comparing different wayfinding designs and show that our optimized designs can guide pedestrians to their destinations effectively. Our approach can also help the designer visualize the accessibility of a destination from different locations, and correct any "blind zone" with additional signs.

40 CFR 85.2104 - Owners' compliance with instructions for proper maintenance and use.

Code of Federal Regulations, 2011 CFR

2011-07-01

... automobiles for the relevant maintenance instruction(s); or (2) A showing that the vehicle has been submitted... to someone who regularly engages in the business of servicing automobiles for the purpose of... area in which the vehicle or engine is located, unless the written instructions for proper maintenance...

40 CFR 85.2104 - Owners' compliance with instructions for proper maintenance and use.

Code of Federal Regulations, 2013 CFR

2013-07-01

... automobiles for the relevant maintenance instruction(s); or (2) A showing that the vehicle has been submitted... to someone who regularly engages in the business of servicing automobiles for the purpose of... area in which the vehicle or engine is located, unless the written instructions for proper maintenance...

40 CFR 85.2104 - Owners' compliance with instructions for proper maintenance and use.

Code of Federal Regulations, 2014 CFR

2014-07-01

... automobiles for the relevant maintenance instruction(s); or (2) A showing that the vehicle has been submitted... to someone who regularly engages in the business of servicing automobiles for the purpose of... area in which the vehicle or engine is located, unless the written instructions for proper maintenance...

40 CFR 85.2104 - Owners' compliance with instructions for proper maintenance and use.

Code of Federal Regulations, 2010 CFR

2010-07-01

... automobiles for the relevant maintenance instruction(s); or (2) A showing that the vehicle has been submitted... to someone who regularly engages in the business of servicing automobiles for the purpose of... area in which the vehicle or engine is located, unless the written instructions for proper maintenance...

40 CFR 85.2104 - Owners' compliance with instructions for proper maintenance and use.

Code of Federal Regulations, 2012 CFR

2012-07-01

... automobiles for the relevant maintenance instruction(s); or (2) A showing that the vehicle has been submitted... to someone who regularly engages in the business of servicing automobiles for the purpose of... area in which the vehicle or engine is located, unless the written instructions for proper maintenance...

Development a heuristic method to locate and allocate the medical centers to minimize the earthquake relief operation time.

PubMed

Aghamohammadi, Hossein; Saadi Mesgari, Mohammad; Molaei, Damoon; Aghamohammadi, Hasan

2013-01-01

Location-allocation is a combinatorial optimization problem, and is defined as Non deterministic Polynomial Hard (NP) hard optimization. Therefore, solution of such a problem should be shifted from exact to heuristic or Meta heuristic due to the complexity of the problem. Locating medical centers and allocating injuries of an earthquake to them has high importance in earthquake disaster management so that developing a proper method will reduce the time of relief operation and will consequently decrease the number of fatalities. This paper presents the development of a heuristic method based on two nested genetic algorithms to optimize this location allocation problem by using the abilities of Geographic Information System (GIS). In the proposed method, outer genetic algorithm is applied to the location part of the problem and inner genetic algorithm is used to optimize the resource allocation. The final outcome of implemented method includes the spatial location of new required medical centers. The method also calculates that how many of the injuries at each demanding point should be taken to any of the existing and new medical centers as well. The results of proposed method showed high performance of designed structure to solve a capacitated location-allocation problem that may arise in a disaster situation when injured people has to be taken to medical centers in a reasonable time.

Oil Motion Control by an Extra Pinning Structure in Electro-Fluidic Display.

PubMed

Dou, Yingying; Tang, Biao; Groenewold, Jan; Li, Fahong; Yue, Qiao; Zhou, Rui; Li, Hui; Shui, Lingling; Henzen, Alex; Zhou, Guofu

2018-04-06

Oil motion control is the key for the optical performance of electro-fluidic displays (EFD). In this paper, we introduced an extra pinning structure (EPS) into the EFD pixel to control the oil motion inside for the first time. The pinning structure canbe fabricated together with the pixel wall by a one-step lithography process. The effect of the relative location of the EPS in pixels on the oil motion was studied by a series of optoelectronic measurements. EPS showed good control of oil rupture position. The properly located EPS effectively guided the oil contraction direction, significantly accelerated switching on process, and suppressed oil overflow, without declining in aperture ratio. An asymmetrically designed EPS off the diagonal is recommended. This study provides a novel and facile way for oil motion control within an EFD pixel in both direction and timescale.

Declustering of clustered preferential sampling for histogram and semivariogram inference

USGS Publications Warehouse

Olea, R.A.

2007-01-01

Measurements of attributes obtained more as a consequence of business ventures than sampling design frequently result in samplings that are preferential both in location and value, typically in the form of clusters along the pay. Preferential sampling requires preprocessing for the purpose of properly inferring characteristics of the parent population, such as the cumulative distribution and the semivariogram. Consideration of the distance to the nearest neighbor allows preparation of resampled sets that produce comparable results to those from previously proposed methods. Clustered sampling of size 140, taken from an exhaustive sampling, is employed to illustrate this approach. ?? International Association for Mathematical Geology 2007.

Development of an Acoustic Localization Method for Cavitation Experiments in Reverberant Environments

NASA Astrophysics Data System (ADS)

Ranjeva, Minna; Thompson, Lee; Perlitz, Daniel; Bonness, William; Capone, Dean; Elbing, Brian

2011-11-01

Cavitation is a major concern for the US Navy since it can cause ship damage and produce unwanted noise. The ability to precisely locate cavitation onset in laboratory scale experiments is essential for proper design that will minimize this undesired phenomenon. Measuring the cavitation onset is more accurately determined acoustically than visually. However, if other parts of the model begin to cavitate prior to the component of interest the acoustic data is contaminated with spurious noise. Consequently, cavitation onset is widely determined by optically locating the event of interest. The current research effort aims at developing an acoustic localization scheme for reverberant environments such as water tunnels. Currently cavitation bubbles are being induced in a static water tank with a laser, allowing the localization techniques to be refined with the bubble at a known location. The source is located with the use of acoustic data collected with hydrophones and analyzed using signal processing techniques. To verify the accuracy of the acoustic scheme, the events are simultaneously monitored visually with the use of a high speed camera. Once refined testing will be conducted in a water tunnel. This research was sponsored by the Naval Engineering Education Center (NEEC).

15 CFR 5.4 - Permits.

Code of Federal Regulations, 2010 CFR

2010-01-01

... standards relating to appearance, safety, sanitation, maintenance, and efficiency of operation. Due regard... the Government and prospective patrons of the stand. (f) The permit shall describe the location of the stand proper and the location of any vending machines which are operated in conjunction with it. ...

Integrating Model-Based Verification into Software Design Education

ERIC Educational Resources Information Center

Yilmaz, Levent; Wang, Shuo

2005-01-01

Proper design analysis is indispensable to assure quality and reduce emergent costs due to faulty software. Teaching proper design verification skills early during pedagogical development is crucial, as such analysis is the only tractable way of resolving software problems early when they are easy to fix. The premise of the presented strategy is…

Design and development of the spinning mode synthesizer

NASA Technical Reports Server (NTRS)

Seiner, J. M.; Reethof, G.

1973-01-01

Design and development of a flexible source of spinning modes which is capable of generating independent spinning waves of controlled complexity and spin speed without the introduction of broad band elements is reported. These features were accomplished through the use of eight commercial loudspeakers located in an equally spaced circular array with diameter of 11 inches and properly phased so that the system could generate a spinning wave. The constructed apparatus was tested in an anechoic environment and found capable of generating a plane, one and two lobed spinning wave of high quality with a sound pressure level of 120 db and at frequencies ranging from 1500 to 2500 Hz at a distance of 4 ft in the far field. The wave speeds investigated varied from 8000 to 18000 rad/sec which represent supersonic peripheral speeds.

Slug Test Characterization Results for Multi-Test/Depth Intervals Conducted During the Drilling of CERCLA Operable Unit OU UP-1 Wells 299-W19-48, 699-30-66, and 699-36-70B

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spane, Frank A.; Newcomer, Darrell R.

2010-06-15

This report presents test descriptions and analysis results for multiple, stress-level slug tests that were performed at selected test/depth intervals within three Operable Unit (OU) UP-1 wells: 299-W19-48 (C4300/Well K), 699-30-66 (C4298/Well R), and 699-36-70B (C4299/Well P). These wells are located within, adjacent to, and to the southeast of the Hanford Site 200-West Area. The test intervals were characterized as the individual boreholes were advanced to their final drill depths. The primary objective of the hydrologic tests was to provide information pertaining to the areal variability and vertical distribution of hydraulic conductivity with depth at these locations within the OUmore » UP-1 area. This type of characterization information is important for predicting/simulating contaminant migration (i.e., numerical flow/transport modeling) and designing proper monitor well strategies for OU and Waste Management Area locations.« less

Slug Test Characterization Results for Multi-Test/Depth Intervals Conducted During the Drilling of CERCLA Operable Unit OU ZP-1 Wells 299-W11-43, 299-W15-50, and 299-W18-16

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spane, Frank A.; Newcomer, Darrell R.

2010-06-21

The following report presents test descriptions and analysis results for multiple, stress level slug tests that were performed at selected test/depth intervals within three Operable Unit (OU) ZP-1 wells: 299-W11-43 (C4694/Well H), 299-W15-50 (C4302/Well E), and 299-W18-16 (C4303/Well D). These wells are located within south-central region of the Hanford Site 200-West Area (Figure 1.1). The test intervals were characterized as the individual boreholes were advanced to their final drill depths. The primary objective of the hydrologic tests was to provide information pertaining to the areal variability and vertical distribution of hydraulic conductivity with depth at these locations within the OUmore » ZP-1 area. This type of characterization information is important for predicting/simulating contaminant migration (i.e., numerical flow/transport modeling) and designing proper monitor well strategies for OU and Waste Management Area locations.« less

Quiet Clean Short-Haul Experimental Engine (QCSEE) aerodynamic characteristics of 30.5 centimeter diameter inlets

NASA Technical Reports Server (NTRS)

Paul, D. L.

1975-01-01

A low speed test program was conducted in a 9- by 15-foot V/STOL wind tunnel to investigate internal performance characteristics and determine key design features required for an inlet to meet the demanding operational conditions of the QCSEE application. Four models each having a design average throat Mach number of 0.79 were tested over a range of incidence angle, throat Mach number, and freestream velocity. Principal design variable was internal lip diameter ratio. Stable, efficient inlet performance was found to be feasible at and beyond the 50 deg incidence angle required by the QCSEE application at its 41.2 m/sec (80 knot) nominal takeoff velocity, through suitably designed inlet lip and diffuser components. Forebody design was found to significantly impact flow stability via nose curvature. Measured inlet wall pressures were used to select a location for the inlet throat Mach number control's static pressure port that properly balanced the conflicting demands of relative insensitivity to flow incidence and sufficiently high response to changes in engine flow demand.

Method of locating related items in a geometric space for data mining

DOEpatents

Hendrickson, B.A.

1999-07-27

A method for locating related items in a geometric space transforms relationships among items to geometric locations. The method locates items in the geometric space so that the distance between items corresponds to the degree of relatedness. The method facilitates communication of the structure of the relationships among the items. The method is especially beneficial for communicating databases with many items, and with non-regular relationship patterns. Examples of such databases include databases containing items such as scientific papers or patents, related by citations or keywords. A computer system adapted for practice of the present invention can include a processor, a storage subsystem, a display device, and computer software to direct the location and display of the entities. The method comprises assigning numeric values as a measure of similarity between each pairing of items. A matrix is constructed, based on the numeric values. The eigenvectors and eigenvalues of the matrix are determined. Each item is located in the geometric space at coordinates determined from the eigenvectors and eigenvalues. Proper construction of the matrix and proper determination of coordinates from eigenvectors can ensure that distance between items in the geometric space is representative of the numeric value measure of the items' similarity. 12 figs.

Method of locating related items in a geometric space for data mining

DOEpatents

Hendrickson, Bruce A.

1999-01-01

A method for locating related items in a geometric space transforms relationships among items to geometric locations. The method locates items in the geometric space so that the distance between items corresponds to the degree of relatedness. The method facilitates communication of the structure of the relationships among the items. The method is especially beneficial for communicating databases with many items, and with non-regular relationship patterns. Examples of such databases include databases containing items such as scientific papers or patents, related by citations or keywords. A computer system adapted for practice of the present invention can include a processor, a storage subsystem, a display device, and computer software to direct the location and display of the entities. The method comprises assigning numeric values as a measure of similarity between each pairing of items. A matrix is constructed, based on the numeric values. The eigenvectors and eigenvalues of the matrix are determined. Each item is located in the geometric space at coordinates determined from the eigenvectors and eigenvalues. Proper construction of the matrix and proper determination of coordinates from eigenvectors can ensure that distance between items in the geometric space is representative of the numeric value measure of the items' similarity.

Investigation of asphalt content design for open-graded bituminous mixes.

DOT National Transportation Integrated Search

1974-01-01

Several design procedures associated with determining the proper asphalt content for open-graded bituminous mixes were investigated. Also considered was the proper amount of tack coat that should be placed on the old surface prior to paving operation...

Electromechanical modeling and power performance analysis of a piezoelectric energy harvester having an attached mass and a segmented piezoelectric layer

NASA Astrophysics Data System (ADS)

Jeong, Sinwoo; Cho, Jae Yong; Sung, Tae Hyun; Yoo, Hong Hee

2017-03-01

Conventional vibration-based piezoelectric energy harvesters (PEHs) have advantages including the ubiquity of their energy source and their ease of manufacturing. However, they have a critical disadvantage as well: they can produce a reasonable amount of power only if the excitation frequency is concentrated near a natural frequency of the PEH. Because the excitation frequency is often spread and/or variable, it is very difficult to successfully design a conventional PEH. In this paper, we propose a new cantilevered PEH whose design includes an attached mass and a segmented piezoelectric layer. By choosing a proper size and location for the attached mass, the gap between the first and second natural frequencies of the PEH can be decreased in order to broaden the effective excitation frequency range and thus to allow reasonable power generation. Especially, the output power performance improves significantly around the second natural frequency of the PEH since the voltage cancellation effect can be made very weak by segmenting the piezoelectric layer at an appropriate location. To investigate the power performance of the new PEH, herein a reduced-order electromechanical analysis model is proposed and the accuracy of this model is validated experimentally. The effects of variable load resistance and piezoelectric layer segmentation location upon the power performance of the new PEH are investigated by means of the reduced-order analysis model.

Review & Peer Review of “Parameters for Properly Designed and Operated Flares” Documents

EPA Pesticide Factsheets

This page contains two 2012 memoranda on the review of EPA's parameters for properly designed and operated flares. One details the process of peer review, and the other provides background information and specific charge questions to the panel.

Intelligent seismic risk mitigation system on structure building

NASA Astrophysics Data System (ADS)

Suryanita, R.; Maizir, H.; Yuniorto, E.; Jingga, H.

2018-01-01

Indonesia located on the Pacific Ring of Fire, is one of the highest-risk seismic zone in the world. The strong ground motion might cause catastrophic collapse of the building which leads to casualties and property damages. Therefore, it is imperative to properly design the structural response of building against seismic hazard. Seismic-resistant building design process requires structural analysis to be performed to obtain the necessary building responses. However, the structural analysis could be very difficult and time consuming. This study aims to predict the structural response includes displacement, velocity, and acceleration of multi-storey building with the fixed floor plan using Artificial Neural Network (ANN) method based on the 2010 Indonesian seismic hazard map. By varying the building height, soil condition, and seismic location in 47 cities in Indonesia, 6345 data sets were obtained and fed into the ANN model for the learning process. The trained ANN can predict the displacement, velocity, and acceleration responses with up to 96% of predicted rate. The trained ANN architecture and weight factors were later used to build a simple tool in Visual Basic program which possesses the features for prediction of structural response as mentioned previously.

Fiber optic cables for transmission of high-power laser pulses in spaceflight applications

NASA Astrophysics Data System (ADS)

Thomes, W. J.; Ott, M. N.; Chuska, R. F.; Switzer, R. C.; Blair, D. E.

2017-11-01

Lasers with high peak power pulses are commonly used in spaceflight missions for a wide range of applications, from LIDAR systems to optical communications. Due to the high optical power needed, the laser has to be located on the exterior of the satellite or coupled through a series of free space optics. This presents challenges for thermal management, radiation resistance, and mechanical design. Future applications will require multiple lasers located close together, which further complicates the design. Coupling the laser energy into a fiber optic cable allows the laser to be relocated to a more favorable position on the spacecraft. Typical fiber optic termination procedures are not sufficient for injection of these high-power laser pulses without catastrophic damage to the fiber endface. In the current study, we will review the causes of fiber damage during high-power injection and discuss our new manufacturing procedures that overcome these issues to permit fiber use with high reliability in these applications. We will also discuss the proper methods for launching the laser pulses into the fiber to avoid damage and how this is being implemented for current spaceflight missions.

Fiber Optic Cables for Transmission of High-Power Laser Pulses in Spaceflight Applications

NASA Technical Reports Server (NTRS)

Thomes, W. J., Jr.; Ott, M. N.; Chuska, R. F.; Switzer, R. C.; Blair, D. E.

2010-01-01

Lasers with high peak power pulses are commonly used in spaceflight missions for a wide range of applications, from LIDAR systems to optical communications. Due to the high optical power needed, the laser has to be located on the exterior of the satellite or coupled through a series of free space optics. This presents challenges for thermal management, radiation resistance, and mechanical design. Future applications will require multiple lasers located close together, which further complicates the design. Coupling the laser energy into a fiber optic cable allows the laser to be relocated to a more favorable position on the spacecraft. Typical fiber optic termination procedures are not sufficient for injection of these high-power laser pulses without catastrophic damage to the fiber endface. In the current study, we will review the causes of fiber damage during high-power injection and discuss our new manufacturing procedures that overcome these issues to permit fiber use with high reliability in these applications. We will also discuss the proper methods for launching the laser pulses into the fiber to avoid damage and how this is being implemented for current spaceflight missions.

Absolute earthquake locations using 3-D versus 1-D velocity models below a local seismic network: example from the Pyrenees

NASA Astrophysics Data System (ADS)

Theunissen, T.; Chevrot, S.; Sylvander, M.; Monteiller, V.; Calvet, M.; Villaseñor, A.; Benahmed, S.; Pauchet, H.; Grimaud, F.

2018-03-01

Local seismic networks are usually designed so that earthquakes are located inside them (primary azimuthal gap <<180°) and close to the seismic stations (0-100 km). With these local or near-regional networks (0°-5°), many seismological observatories still routinely locate earthquakes using 1-D velocity models. Moving towards 3-D location algorithms requires robust 3-D velocity models. This work takes advantage of seismic monitoring spanning more than 30 yr in the Pyrenean region. We investigate the influence of a well-designed 3-D model with station corrections including basins structure and the geometry of the Mohorovicic discontinuity on earthquake locations. In the most favourable cases (GAP < 180° and distance to the first station lower than 15 km), results using 1-D velocity models are very similar to 3-D results. The horizontal accuracy in the 1-D case can be higher than in the 3-D case if lateral variations in the structure are not properly resolved. Depth is systematically better resolved in the 3-D model even on the boundaries of the seismic network (GAP > 180° and distance to the first station higher than 15 km). Errors on velocity models and accuracy of absolute earthquake locations are assessed based on a reference data set made of active seismic, quarry blasts and passive temporary experiments. Solutions and uncertainties are estimated using the probabilistic approach of the NonLinLoc (NLLoc) software based on Equal Differential Time. Some updates have been added to NLLoc to better focus on the final solution (outlier exclusion, multiscale grid search, S-phases weighting). Errors in the probabilistic approach are defined to take into account errors on velocity models and on arrival times. The seismicity in the final 3-D catalogue is located with a horizontal uncertainty of about 2.0 ± 1.9 km and a vertical uncertainty of about 3.0 ± 2.0 km.

78 FR 40149 - Scientific Information Request on Chronic Urinary Retention (CUR) Treatment

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-03

... improve the quality of this review. AHRQ is conducting this comparative effectiveness review pursuant to..., study period, design, methodology, indication and diagnosis, proper use instructions, inclusion and... study number, the study period, design, methodology, indication and diagnosis, proper use instructions...

Manipulating Steady Heat Conduction by Sensu-shaped Thermal Metamaterials

PubMed Central

Han, Tiancheng; Bai, Xue; Liu, Dan; Gao, Dongliang; Li, Baowen; Thong, John T. L.; Qiu, Cheng-Wei

2015-01-01

The ability to design the control of heat flow has innumerable benefits in the design of electronic systems such as thermoelectric energy harvesters, solid-state lighting, and thermal imagers, where the thermal design plays a key role in performance and device reliability. In this work, we employ one identical sensu-unit with facile natural composition to experimentally realize a new class of thermal metamaterials for controlling thermal conduction (e.g., thermal concentrator, focusing/resolving, uniform heating), only resorting to positioning and locating the same unit element of sensu-shape structure. The thermal metamaterial unit and the proper arrangement of multiple identical units are capable of transferring, redistributing and managing thermal energy in a versatile fashion. It is also shown that our sensu-shape unit elements can be used in manipulating dc currents without any change in the layout for the thermal counterpart. These could markedly enhance the capabilities in thermal sensing, thermal imaging, thermal-energy storage, thermal packaging, thermal therapy, and more domains beyond. PMID:25974383

Helicopter vibration suppression using simple pendulum absorbers on the rotor blade

NASA Technical Reports Server (NTRS)

Pierce, G. A.; Hanouva, M. N. H.

1982-01-01

A comprehensive anaytical design procedure for the installation of simple pendulums on the blades of a helicopter rotor to suppress the root reactions is presented. A frequency response anaysis is conducted of typical rotor blades excited by a harmonic variation of spanwise airload distributions as well as a concentrated load at the tip. The results presented included the effect of pendulum tuning on the minimization of the hub reactions. It is found that a properly designed flapping pendulum attenuates the root out-of-plane force and moment whereas the optimum designed lead-lag pendulum attenuates the root in-plane reactions. For optimum pendulum tuning the parameters to be determined are the pendulum uncoupled natural frequency, the pendulum spanwise location and its mass. It is found that the optimum pendulum frequency is in the vicinity of the excitation frequency. For the optimum pendulum a parametric study is conducted. The parameters varied include prepitch, pretwist, precone and pendulum hinge offset.

Selection of physiological parameters for optoelectronic system supporting behavioral therapy of autistic children

NASA Astrophysics Data System (ADS)

Landowska, A.; Karpienko, K.; Wróbel, M.; Jedrzejewska-Szczerska, M.

2014-11-01

In this article the procedure of selection of physiological parameters for optoelectronic system supporting behavioral therapy of autistic children is proposed. Authors designed and conducted an experiment in which a group of 30 health volunteers (16 females and 14 males) were examined. Under controlled conditions people were exposed to a stressful situation caused by the picture or sound (1kHz constant sound, which was gradually silenced and finished with a shot sound). For each of volunteers, a set of physiological parameters were recorded, including: skin conductance, heart rate, peripheral temperature, respiration rate and electromyography. The selected characteristics were measured in different locations in order to choose the most suitable one for the designed therapy supporting system. The bio-statistical analysis allowed us to discern the proper physiological parameters that are most associated to changes due to emotional state of a patient, such as: skin conductance, temperatures and respiration rate. This allowed us to design optoelectronic sensors network for supporting behavioral therapy of children with autism.

Design of UWB Monopole Antenna with Dual Notched Bands Using One Modified Electromagnetic-Bandgap Structure

PubMed Central

Xu, Ziqiang

2013-01-01

A modified electromagnetic-bandgap (M-EBG) structure and its application to planar monopole ultra-wideband (UWB) antenna are presented. The proposed M-EBG which comprises two strip patch and an edge-located via can perform dual notched bands. By properly designing and placing strip patch near the feedline, the proposed M-EBG not only possesses a simple structure and compact size but also exhibits good band rejection. Moreover, it is easy to tune the dual notched bands by altering the dimensions of the M-EBG. A demonstration antenna with dual band-notched characteristics is designed and fabricated to validate the proposed method. The results show that the proposed antenna can satisfy the requirements of VSWR < 2 over UWB 3.1–10.6 GHz, except for the rejected bands of the world interoperability for microwave access (WiMAX) and the wireless local area network (WLAN) at 3.5 GHz and 5.5 GHz, respectively. PMID:24170984

Esthetic abutment design for angulated screw channels: A technical report.

PubMed

Sakamoto, Satoshi; Ro, Munehiko; Al Ardah, Aladdin; Goodacre, Charles

2017-11-15

Angulated screw channel system abutments (ASCs) have recently been introduced to address the problem with visible screw access that may compromise esthetics. ASCs allow the screw access to be modified up to 25 degrees relative to the implant axis. However, a widened channel, which may cause thinning of the facial ceramic, is needed at the implant screw head to allow for proper engagement of the screwdriver. This technical report introduces a custom titanium insert design, the Satoshi Sakamoto (SS) abutment. The SS abutment consists of a custom titanium metal insert and zirconia coping in which the access hole is located in an esthetic position with an ASC system. The SS abutment results in a crown with more normal crown dimensions that also provides more space for the soft tissues. This SS abutment design allows clinicians to obtain screw-retained restorations with optimal esthetics and mechanical strength. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

49 CFR 571.225 - Standard No. 225; Child restraint anchorage systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... strength steel tether hook for attachment to the tether anchorage. The tether hook meets the specifications... systems to ensure their proper location and strength for the effective securing of child restraints, to... manufactured on or after September 1, 1999, shall comply with the configuration, location, marking and strength...

49 CFR 571.225 - Standard No. 225; Child restraint anchorage systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... strength steel tether hook for attachment to the tether anchorage. The tether hook meets the specifications... systems to ensure their proper location and strength for the effective securing of child restraints, to... manufactured on or after September 1, 1999, shall comply with the configuration, location, marking and strength...

49 CFR 571.225 - Standard No. 225; Child restraint anchorage systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... strength steel tether hook for attachment to the tether anchorage. The tether hook meets the specifications... systems to ensure their proper location and strength for the effective securing of child restraints, to... manufactured on or after September 1, 1999, shall comply with the configuration, location, marking and strength...

Determination of piglet location in farrowing crates based on depth and digital images

USDA-ARS?s Scientific Manuscript database

Understanding and properly managing behavioral responses of prewean piglets to the farrowing environment can improve well-being and pre-weaning performance of the piglets. This paper aims to quantify piglet location in the farrowing crate as affected by the lactating sow’s lying posture. Each farrow...

Cellular Factors Shape 3D Genome Landscape

Cancer.gov

Researchers, using novel large-scale imaging technology, have mapped the spatial location of individual genes in the nucleus of human cells and identified 50 cellular factors required for the proper 3D positioning of genes. These spatial locations play important roles in gene expression, DNA repair, genome stability, and other cellular activities.

78 FR 11171 - Proposed Information Collection Request; Comment Request; RadNet (Renewal)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-15

...) Evaluate whether the proposed collection of information is necessary for the proper performance of the functions of the Agency, including whether the information will have practical utility; (ii) evaluate the... request descriptive information pertaining to sample location, e.g., sample type, sample location, length...

Engineering criteria for fracture flowback procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barree, R.D.; Mukherjee, H.

1995-12-31

Post treatment fracture flowback procedures during closure are often critical to the retention of fracture conductivity near the wellbore. Postfrac production performance largely depends on this conductivity. The importance of proper flowback procedure has been documented in the fracture industry, but definitive guidelines for flowback design have never been established. As a result, many misconceptions exist regarding the physics of proppant flowback and its effects on the final proppant distribution in the fracture. This paper presents a rigorous study of fracture flowback and proppant migration during closure using a fully three-dimensional fracture geometry simulator (GOHFER). The effects of rate ofmore » flowback, location of the perforation interval, final proppant concentration, and the fracture geometry prior to flowback on the retained post closure proppant concentration are discussed. Consideration is given to the fluid velocity field in the created fracture resulting from the flowback, and its effects on proppant movement and localized fracture closure. These studies illustrate the difference between ``forced closure`` and ``reverse screenout`` concepts in flowback design. Other effects such as crossflow between multiple perforated layers are also studied. Simulation studies indicate that selection of a desirable flowback rate is very sensitive to crossflow effects resulting from induced fractures in multiple stress layers. This crossflow can result in significant overflushing of proppant in the lower stress zones, if not countered by properly applied flowback procedures.« less

Friction loss in straight pipes of unplasticized polyvinyl chloride.

PubMed

Iwasaki, T; Ojima, J

1996-01-01

In order to design proper ductwork for a local exhaust system, airflow characteristics were investigated in straight pipes of unplasticized polyvinyl chloride (PVC). A linear decrease in static pressure was observed downstream at points from the opening of the VU pipes (JIS K 6741) located at distances greater than 10 times the pipe diameter, for velocities ranging between 10.18-36.91 m/s. Roughness inside pipes with small diameters was found to be 0.0042-0.0056 mm and the friction factor was calculated on the basis of Colebrook's equation for an airflow transition zone. An extended friction chart was then constructed on the basis of the roughness value and the friction factor. This chart can be applied when designing a local exhaust system with the ducts of diameters ranging from 40 to 900 mm. The friction loss of the PVC pipe was found to be approximately 2/3 of that of a galvanized steel pipe.

78 FR 52929 - Scientific Information Request on Imaging Tests for the Diagnosis and Staging of Pancreatic...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-27

... improve the quality of this review. AHRQ is conducting this comparative effectiveness review pursuant to..., study period, design, methodology, indication and diagnosis, proper use instructions, inclusion and... including a study number, the study period, design, methodology, indication and diagnosis, proper use...

Optimum Design of a Ceramic Tensile Creep Specimen Using a Finite Element Method

PubMed Central

Wang, Z.; Chiang, C. K.; Chuang, T.-J.

1997-01-01

An optimization procedure for designing a ceramic tensile creep specimen to minimize stress concentration is carried out using a finite element method. The effect of pin loading and the specimen geometry are considered in the stress distribution calculations. A growing contact zone between the pin and the specimen has been incorporated into the problem solution scheme as the load is increased to its full value. The optimization procedures are performed for the specimen, and all design variables including pinhole location and pinhole diameter, head width, neck radius, and gauge length are determined based on a set of constraints imposed on the problem. In addition, for the purpose of assessing the possibility of delayed failure outside the gage section, power-law creep in the tensile specimen is considered in the analysis. Using a particular grade of advanced ceramics as an example, it is found that if the specimen is not designed properly, significant creep deformation and stress redistribution may occur in the head of the specimen resulting in undesirable (delayed) head failure of the specimen during the creep test. PMID:27805126

Wave simulation for the design of an innovative quay wall: the case of Vlorë Harbour

NASA Astrophysics Data System (ADS)

Antonini, Alessandro; Archetti, Renata; Lamberti, Alberto

2017-01-01

Sea states and environmental conditions are basic data for the design of marine structures. Hindcasted wave data have been applied here with the aim of identifying the proper design conditions for an innovative quay wall concept. In this paper, the results of a computational fluid dynamics model are used to optimise the new absorbing quay wall of Vlorë Harbour (Republic of Albania) and define the design loads under extreme wave conditions. The design wave states at the harbour entrance have been estimated analysing 31 years of hindcasted wave data simulated through the application of WaveWatch III. Due to the particular geography and topography of the Bay of Vlorë, wave conditions generated from the north-west are transferred to the harbour entrance with the application of a 2-D spectral wave module, whereas southern wave states, which are also the most critical for the port structures, are defined by means of a wave generation model, according to the available wind measurements. Finally, the identified extreme events have been used, through the NewWave approach, as boundary conditions for the numerical analysis of the interaction between the quay wall and the extreme events. The results show that the proposed method, based on numerical modelling at different scales from macro to meso and to micro, allows for the identification of the best site-specific solutions, also for a location devoid of any wave measurement. In this light, the objectives of the paper are two-fold. First, they show the application of sea condition estimations through the use of wave hindcasted data in order to properly define the design wave conditions for a new harbour structure. Second, they present a new approach for investigating an innovative absorbing quay wall based on CFD modelling and the NewWave theory.

IR window design for hypersonic missile seekers: thermal shock and cooling systems

NASA Astrophysics Data System (ADS)

Hingst, Uwe; Koerber, Stefan

2001-10-01

Infra-red (IR) seekers on missiles at high Mach-numbers in the lower tier air defence often suffer from degradation in performance due to aerothermodynamic effects. The kind and rate of degradation depends on the geometric design (shape) and location of the IR-window. Optimal design may reduce those effects but still misses to totally withstand the imposed thermal stresses (thermal shock). Proper thermal protection systems and/or window cooling systems will be needed. The first part of this paper deals particularly with passive IR- window design features to reduce the thermal stresses. A series of wind-tunnel testings focused on the thermal shock behavior of different IR-window shapes under critical flight conditions. The variation of typical design parameters demonstrates the available features to reduce thermal shock by passive ways. The second part presents active thermal stress reduction devices, e.g. an active cooling system. Among others the most efficient reduction of thermal heating is based on three components: A partial coverage of the IR-dome to protect most parts against heating effects, a rotating system bearing the IR-dome and a liquid spray-cooling system in the gap between the cover and the IR-dome. The hemispherical or pyramidal dome can be located either midways in the missile nose section or sideways on the structure. The liquid spray cooling system combines both, a heat exchange by fluid evaporation and a heat transfer by fluid and gas cross flow (convection), causing a low fluid consumption. Such a cooling system along with their driving parameters and the resulting analytical performance will be presented.

Recommendations for research design of telehealth studies.

PubMed

Chumbler, Neale R; Kobb, Rita; Brennan, David M; Rabinowitz, Terry

2008-11-01

Properly designed randomized controlled trials (RCTs) are the gold standard to use when examining the effectiveness of telehealth interventions on clinical outcomes. Some published telehealth studies have employed well-designed RCTs. However, such methods are not always feasible and practical in particular settings. This white paper addresses not only the need for properly designed RCTs, but also offers alternative research designs, such as quasi-experimental designs, and statistical techniques that can be employed to rigorously assess the effectiveness of telehealth studies. This paper further offers design and measurement recommendations aimed at and relevant to administrative decision-makers, policymakers, and practicing clinicians.

Entry Debris Field Estimation Methods and Application to Compton Gamma Ray Observatory Disposal

NASA Technical Reports Server (NTRS)

Mrozinski, Richard B.

2001-01-01

For public safety reasons, the Compton Gamma Ray Observatory (CGRO) was intentionally deorbited on June 4, 2000. This deorbit was NASA's first intentional controlled deorbit of a satellite, and more will come including the eventual deorbit of the International Space Station. To maximize public safety, satellite deorbit planning requires conservative estimates of the debris footprint size and location. These estimates are needed to properly design a deorbit sequence that places the debris footprint over unpopulated areas, including protection for deorbit contingencies. This paper details a method for estimating the length (range), width (crossrange), and location of entry and breakup debris footprints. This method utilizes a three degree-of-freedom Monte Carlo simulation incorporating uncertainties in all aspects of the problem, including vehicle and environment uncertainties. The method incorporates a range of debris characteristics based on historical data in addition to any vehicle-specific debris catalog information. This paper describes the method in detail, and presents results of its application as used in planning the deorbit of the CGRO.

High resolution EUV monochromator/spectrometer

DOEpatents

Koike, Masako

1996-01-01

This invention is related to a monochromator which employs a spherical mirror, a traveling plane mirror with simultaneous rotation, and a varied spacing plane grating. The divergent beam from the entrance slit is converged by the spherical mirror located at the various positions in the monochromator depending of the inventive system. To provide the meaningful diffraction efficiencies and to reduce unwanted higher order lights, the deviation angle subtending the incidence and diffraction beams for the plane grating is varied with the position of the traveling plane mirror with simultaneous rotation located in the front or back of the plane grating with wavelength scanning. The outgoing beam from the monochromator goes through the fixed exit slit and has same beam direction regardless of the scanning wavelength. The combination of properly designed motions of the plane mirror and novel varied-spacing parameters of the inventive plane grating corrects the aberrations and focuses the monochromatic spectral image on the exit slit, enabling measurements at high spectral resolution.

High resolution EUV monochromator/spectrometer

DOEpatents

Koike, Masako

1996-06-18

This invention is related to a monochromator which employs a spherical mirror, a traveling plane mirror with simultaneous rotation, and a varied spacing plane grating. The divergent beam from the entrance slit is converged by the spherical mirror located at the various positions in the monochromator depending of the inventive system. To provide the meaningful diffraction efficiencies and to reduce unwanted higher order lights, the deviation angle subtending the incidence and diffraction beams for the plane grating is varied with the position of the traveling plane mirror with simultaneous rotation located in the front or back of the plane grating with wavelength scanning. The outgoing beam from the monochromator goes through the fixed exit slit and has same beam direction regardless of the scanning wavelength. The combination of properly designed motions of the plane mirror and novel varied-spacing parameters of the inventive plane grating corrects the aberrations and focuses the monochromatic spectral image on the exit slit, enabling measurements at high spectral resolution. 10 figs.

49 CFR 571.225 - Standard No. 225; Child restraint anchorage systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... N of preload prior to the test. The strap is fitted at one end with a high strength steel tether... systems to ensure their proper location and strength for the effective securing of child restraints, to... manufactured on or after September 1, 1999, shall comply with the configuration, location, marking and strength...

30 CFR 250.203 - Where can wells be located under an EP, DPP, or DOCD?

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL... that can be economically drilled for proper reservoir management; (e) Location of drilling units and platforms; (f) Extent and thickness of the reservoir; (g) Geologic and other reservoir characteristics; (h...

Asteroid proper elements and secular resonances

NASA Technical Reports Server (NTRS)

Knezevic, Zoran; Milani, Andrea

1992-01-01

In a series of papers (e.g., Knezevic, 1991; Milani and Knezevic, 1990; 1991) we reported on the progress we were making in computing asteroid proper elements, both as regards their accuracy and long-term stability. Additionally, we reported on the efficiency and 'intelligence' of our software. At the same time, we studied the associated problems of resonance effects, and we introduced the new class of 'nonlinear' secular resonances; we determined the locations of these secular resonances in proper-element phase space and analyzed their impact on the asteroid family classification. Here we would like to summarize the current status of our work and possible further developments.

The Quality Control Algorithms Used in the Process of Creating the NASA Kennedy Space Center Lightning Protection System Towers Meteorological Database

NASA Technical Reports Server (NTRS)

Orcutt, John M.; Brenton, James C.

2016-01-01

The methodology and the results of the quality control (QC) process of the meteorological data from the Lightning Protection System (LPS) towers located at Kennedy Space Center (KSC) launch complex 39B (LC-39B) are documented in this paper. Meteorological data are used to design a launch vehicle, determine operational constraints, and to apply defined constraints on day-of-launch (DOL). In order to properly accomplish these tasks, a representative climatological database of meteorological records is needed because the database needs to represent the climate the vehicle will encounter. Numerous meteorological measurement towers exist at KSC; however, the engineering tasks need measurements at specific heights, some of which can only be provided by a few towers. Other than the LPS towers, Tower 313 is the only tower that provides observations up to 150 m. This tower is located approximately 3.5 km from LC-39B. In addition, data need to be QC'ed to remove erroneous reports that could pollute the results of an engineering analysis, mislead the development of operational constraints, or provide a false image of the atmosphere at the tower's location.

Lunar Landing Trajectory Design for Onboard Hazard Detection and Avoidance

NASA Technical Reports Server (NTRS)

Paschall, Steve; Brady, Tye; Sostaric, Ron

2009-01-01

The Autonomous Landing and Hazard Avoidance Technology (ALHAT) Project is developing the software and hardware technology needed to support a safe and precise landing for the next generation of lunar missions. ALHAT provides this capability through terrain-relative navigation measurements to enhance global-scale precision, an onboard hazard detection system to select safe landing locations, and an Autonomous Guidance, Navigation, and Control (AGNC) capability to process these measurements and safely direct the vehicle to a landing location. This paper focuses on the key trajectory design issues relevant to providing an onboard Hazard Detection and Avoidance (HDA) capability for the lander. Hazard detection can be accomplished by the crew visually scanning the terrain through a window, a sensor system imaging the terrain, or some combination of both. For ALHAT, this hazard detection activity is provided by a sensor system, which either augments the crew s perception or entirely replaces the crew in the case of a robotic landing. Detecting hazards influences the trajectory design by requiring the proper perspective, range to the landing site, and sufficient time to view the terrain. Following this, the trajectory design must provide additional time to process this information and make a decision about where to safely land. During the final part of the HDA process, the trajectory design must provide sufficient margin to enable a hazard avoidance maneuver. In order to demonstrate the effects of these constraints on the landing trajectory, a tradespace of trajectory designs was created for the initial ALHAT Design Analysis Cycle (ALDAC-1) and each case evaluated with these HDA constraints active. The ALHAT analysis process, described in this paper, narrows down this tradespace and subsequently better defines the trajectory design needed to support onboard HDA. Future ALDACs will enhance this trajectory design by balancing these issues and others in an overall system design process.

Bayesian SEM for Specification Search Problems in Testing Factorial Invariance.

PubMed

Shi, Dexin; Song, Hairong; Liao, Xiaolan; Terry, Robert; Snyder, Lori A

2017-01-01

Specification search problems refer to two important but under-addressed issues in testing for factorial invariance: how to select proper reference indicators and how to locate specific non-invariant parameters. In this study, we propose a two-step procedure to solve these issues. Step 1 is to identify a proper reference indicator using the Bayesian structural equation modeling approach. An item is selected if it is associated with the highest likelihood to be invariant across groups. Step 2 is to locate specific non-invariant parameters, given that a proper reference indicator has already been selected in Step 1. A series of simulation analyses show that the proposed method performs well under a variety of data conditions, and optimal performance is observed under conditions of large magnitude of non-invariance, low proportion of non-invariance, and large sample sizes. We also provide an empirical example to demonstrate the specific procedures to implement the proposed method in applied research. The importance and influences are discussed regarding the choices of informative priors with zero mean and small variances. Extensions and limitations are also pointed out.

Lumber defect detection abilities of furniture rough mill employees

Treesearch

Henry A. Huber; Charles W. McMillin; John P. McKinney

1985-01-01

To cut parts from boards, rough mill employees must be able to see defects, calculate the proper location of cuts, manually position the board, and remain alert. The objective of this study was to evaluate how well rough mill employees perform the task of recognizing, locating, and identifying surface defects independent of the calculation and positioning process....

Mechanisms for the elevation structure of a giant telescope

NASA Astrophysics Data System (ADS)

Hu, Shouwei; Song, Xiaoli; Zhang, Hui

2018-06-01

This paper describes an innovative mechanism based on hydrostatic pads and linear motors for the elevation structure of next-generation extremely large telescopes. Both hydrostatic pads and linear motors are integrated on the frame that includes a kinematical joint, such that the upper part is properly positioned with respect to the elevation runner tracks, while the lower part is connected to the azimuth structure. Potential deflections of the elevation runner bearings at the radial pad locations are absorbed by this flexible kinematic connection and not transmitted to the linear motors and hydrostatic pads. Extensive simulations using finite-element analysis are carried out to verify that the auxiliary whiffletree hydraulic design of the mechanism is sufficient to satisfy the assigned optical length variation errors.

Mechanisms for the elevation structure of a giant telescope

NASA Astrophysics Data System (ADS)

Hu, Shouwei; Song, Xiaoli; Zhang, Hui

2018-05-01

This paper describes an innovative mechanism based on hydrostatic pads and linear motors for the elevation structure of next-generation extremely large telescopes. Both hydrostatic pads and linear motors are integrated on the frame that includes a kinematical joint, such that the upper part is properly positioned with respect to the elevation runner tracks, while the lower part is connected to the azimuth structure. Potential deflections of the elevation runner bearings at the radial pad locations are absorbed by this flexible kinematic connection and not transmitted to the linear motors and hydrostatic pads. Extensive simulations using finite-element analysis are carried out to verify that the auxiliary whiffletree hydraulic design of the mechanism is sufficient to satisfy the assigned optical length variation errors.

Influence of definition of impeller-vaneless diffuser boundary on physical validity of numerical simulations of viscid flow in the vaneless diffuser of a centrifugal compressor: A short review of case studies

NASA Astrophysics Data System (ADS)

Kabalyk, K.; Kryllowicz, W.

2017-09-01

The study aims to work out a set of recommendations for setting a proper distance between the trailing edge of impeller and the interface boundary, which on the one hand would not be too large to overpredict the impeller efficiency and not too short to introduce artificial wake-like flow structures at diffuser inlet on the other. Three individual two-element stages belonging to three different types known as medium- and low-flow coefficient stages are studied. Besides of the design flow coefficient, the focus is on the influence of impeller tip Mach number on the optimal location of the boundary.

Automatic brightness control of laser spot vision inspection system

NASA Astrophysics Data System (ADS)

Han, Yang; Zhang, Zhaoxia; Chen, Xiaodong; Yu, Daoyin

2009-10-01

The laser spot detection system aims to locate the center of the laser spot after long-distance transmission. The accuracy of positioning laser spot center depends very much on the system's ability to control brightness. In this paper, an automatic brightness control system with high-performance is designed using the device of FPGA. The brightness is controlled by combination of auto aperture (video driver) and adaptive exposure algorithm, and clear images with proper exposure are obtained under different conditions of illumination. Automatic brightness control system creates favorable conditions for positioning of the laser spot center later, and experiment results illuminate the measurement accuracy of the system has been effectively guaranteed. The average error of the spot center is within 0.5mm.

5 CFR 960.103 - Location.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., Minneapolis-St. Paul, New Orleans, New York, Newark, Philadelphia, Pittsburgh, Portland, St. Louis, San... Federal Executive Boards, or establish new Federal Executive Boards, as he may deem necessary, proper or...

Destination Information System for Bandung City Using Location-Based Services (LBS) on Android

NASA Astrophysics Data System (ADS)

Kurniawan, B.; Pranoto, H.

2018-02-01

Bandung is a city in West Java, Indonesia with many interesting locations to visit. For most favourite destinations, we can easily look for it on Google and we will find some blogs there discussing about related content. The problem is we can not guarantee that the destination is frequented by visitor. In this research, we utilizes an application to help everyone choosing destination frequented by visitor. The use of information technology in the form of picture, maps, and textual on Android application makes it possible for user to have information about destination with its visitor in a period of time. If destination has visit history, selection of proper destination will be given with fresh informations. This application can run well on Android Lollipop (API Level 21) or above with a minimum RAM of 2 GB since it will compare two coordinates for every data. The use of this app make it possible to access information about location with its visitor history and could help choosing proper destinations for the users.

Introducing Proper Chemical Hygiene and Safety in the General Chemistry Curriculum

NASA Astrophysics Data System (ADS)

Miller, Gordon J.; Heideman, Stephen A.; Greenbowe, Thomas J.

2000-09-01

Chemical safety is an important component of science education for everyone, not just for chemistry majors. Developing a responsible and knowledgeable attitude towards chemical safety best starts at the early stages of a student's career. In many colleges and universities, safety education in undergraduate chemistry has been relegated primarily to a few regulatory documents at the beginning of a laboratory course, or an occasional warning in the description of a specific experiment in a prelaboratory lecture. Safety issues are seldom raised in general chemistry or organic chemistry lecture-based chemistry courses. At Iowa State University we have begun to implement a program, Chemical Hygiene and Safety in the Laboratory, into the undergraduate chemistry curriculum. This program is designed to increase the awareness and knowledge of proper chemical hygiene and laboratory safety issues among all students taking general chemistry and organic chemistry courses. Laboratory protocol, use of safety equipment, familiarity with MSD sheets, basics of first aid, some specific terminology surrounding chemical hygiene, EPA and OSHA requirements, and the use of the World Wide Web to search and locate chemical safety information are topics that are applied throughout the chemistry curriculum. The novelty of this approach is to incorporate MSD sheets and safety information that can be located on the World Wide Web in a series of safety problems and assignments, all related to the chemistry experiments students are about to perform. The fundamental idea of our approach is not only to teach students what is required for appropriate safety measures, but also to involve them in the enforcement of basic prudent practices.

Study/experimental/research design: much more than statistics.

PubMed

Knight, Kenneth L

2010-01-01

The purpose of study, experimental, or research design in scientific manuscripts has changed significantly over the years. It has evolved from an explanation of the design of the experiment (ie, data gathering or acquisition) to an explanation of the statistical analysis. This practice makes "Methods" sections hard to read and understand. To clarify the difference between study design and statistical analysis, to show the advantages of a properly written study design on article comprehension, and to encourage authors to correctly describe study designs. The role of study design is explored from the introduction of the concept by Fisher through modern-day scientists and the AMA Manual of Style. At one time, when experiments were simpler, the study design and statistical design were identical or very similar. With the complex research that is common today, which often includes manipulating variables to create new variables and the multiple (and different) analyses of a single data set, data collection is very different than statistical design. Thus, both a study design and a statistical design are necessary. Scientific manuscripts will be much easier to read and comprehend. A proper experimental design serves as a road map to the study methods, helping readers to understand more clearly how the data were obtained and, therefore, assisting them in properly analyzing the results.

NASA/USRA advanced space design program: The laser powered interorbital vehicle

NASA Technical Reports Server (NTRS)

1989-01-01

A preliminary design is presented for a low-thrust Laser Powered Interorbital Vehicle (LPIV) intended for cargo transportation between an earth space station and a lunar base. The LPIV receives its power from two iodide laser stations, one orbiting the earth and the other located on the surface of the moon. The selected mission utilizes a spiral trajectory, characteristic of a low-thrust spacecraft, requiring 8 days for a lunar rendezvous and an additional 9 days for return. The ship's configuration consists primarily of an optical train, two hydrogen plasma engines, a 37.1 m box beam truss, a payload module, and fuel tanks. The total mass of the vehicle fully loaded is 63300 kg. A single plasma, regeneratively cooled engine design is incorporated into the two 500 N engines. These are connected to the spacecraft by turntables which allow the vehicle to thrust tangentially to the flight path. Proper collection and transmission of the laser beam to the thrust chambers is provided through the optical train. This system consists of the 23 m diameter primary mirror, a convex parabolic secondary mirror, a beam splitter and two concave parabolic tertiary mirrors. The payload bay is capable of carrying 18000 kg of cargo. The module is located opposite the primary mirror on the main truss. Fuel tanks carrying a maximum of 35000 kg of liquid hydrogen are fastened to tracks which allow the tanks to be moved perpendicular to the main truss. This capability is required to prevent the center of mass from moving out of the thrust vector line. The laser beam is located and tracked by means of an acquisition, pointing and tracking system which can be locked onto the space-based laser station. Correct orientation of the spacecraft with the laser beam is maintained by control moment gyros and reaction control rockets. Additionally an aerobrake configuration was designed to provide the option of using the atmospheric drag in place of propulsion for a return trajectory.

Mason Bee Habitations: Teaching Proper "Making" Skill through Authentic Engineering Design Contests. Resources in Technology and Engineering

ERIC Educational Resources Information Center

Cool, Nate; Strimel, Greg J.; Croly, Michael; Grubbs, Michael E.

2017-01-01

To be technologically and engineering literate, people should be able to "make" or produce quality solutions to engineering design challenges while recognizing and understanding how to avoid hazards in a broad array of situations when properly using tools, machines, and materials (Haynie, 2009; Gunter, 2007; ITEA/ITEEA, 2000/2002/2007).…

Quality Improvement of Ground Works Process with the Use of Chosen Lean Management Tools - Case Study

NASA Astrophysics Data System (ADS)

Nowotarski, Piotr; Paslawski, Jerzy; Wysocki, Bartosz

2017-12-01

Ground works are one of the first processes connected with erecting structures. Based on ground conditions like the type of soil or level of underground water different types and solutions for foundations are designed. Foundations are the base for the buildings, and their proper design and execution is the key for the long and faultless use of the whole construction and might influence on the future costs of the eventual repairs (especially when ground water level is high, and there is no proper water insulation made). Article presents the introduction of chosen Lean Management tools for quality improvement of the process of ground works based on the analysis made on the construction site of vehicle control station located in Poznan, Poland. Processes assessment is made from different perspectives taking into account that 3 main groups of workers were directly involved in the process: blue collar-workers, site manager and site engineers. What is more comparison is made on the 3 points of view to the problems that might occur during this type of works, with details analysis on the causes of such situation? Authors presents also the change of approach of workers directly involved in the mentioned processes regarding introduction of Lean Management methodology, which illustrates the problem of scepticism for new ideas of the people used to perform works and actions in traditional way. Using Lean Management philosophy in construction is a good idea to streamline processes in company, get rid of constantly recurring problems, and in this way improve the productivity and quality of executed activities. Performed analysis showed that different groups of people have very different idea and opinion on the problems connected with executing the same process - ground works and only having full picture of the situation (especially in construction processes) management can take proper problems-preventing actions that consequently can influence on the amount of waste generated on the construction cite which positively influence on the external environment.

Staphylococcus aureus Recovery From Environmental and Human Locations in 2 Collegiate Athletic Teams

PubMed Central

Oller, Anna R.; Province, Larry; Curless, Brian

2010-01-01

Abstract Context: Staphylococcus aureus is spread via direct contact with persons and indirect contact via environmental surfaces such as weight benches. Athletes participating in direct-contact sports have an increased risk of acquiring S aureus infections. Objective: To determine (1) potential environmental reservoirs of S aureus in football and wrestling locker rooms and weight rooms, (2) environmental bacterial status after employing more stringent cleaning methods, (3) differences in colonization rates between athletes and nonathletes, (4) exposed body locations where Staphylococcus was recovered more frequently, and (5) personal hygiene practices of athletes and nonathletes. Design: Cross-sectional study. Setting: Locker room and strengthening and conditioning facilities at a National Collegiate Athletic Association Division II university. Patients or Other Participants: Collegiate football players and wrestlers, with nonathlete campus residents serving as the control group. Intervention(s): Infection control methods, education of the custodial staff, and education of the athletes regarding the Centers for Disease Control and Prevention guidelines for infection prevention. Main Outcome Measure(s): Cultures were taken from the participants' noses, fingertips, knuckles, forearms, and shoes and from the environment. Results: Before the intervention, from the 108 environmental samples taken from the football locker room and weight room, 26 (24%) contained methicillin-susceptible S aureus (MSSA) and 33 (31%) contained methicillin-resistant S aureus (MRSA). From the 39 environmental samples taken from the wrestling locker room and pit areas, 1 (3%) contained MSSA and 4 (10%) contained MRSA. The MRSA rates were different between the 2 locations according to a χ2 test (P  =  .01). Seven MRSA isolates were recovered from football players and 1 from a wrestler; no MRSA isolates were recovered from the control group. The fingertip location of S aureus recovery from football players was significant when compared with both other locations in football players and fingertips in wrestlers and the control group (P < .05). Football players and wrestlers shared more personal items than the control group (P < .05). After the intervention, the football locker room and weight room samples were negative for S aureus. Conclusions: Intact strengthening and conditioning equipment, proper hygiene, and proper disinfection methods lowered both environmental and human S aureus recovery at 1 university. PMID:20446834

Neural Correlates of Temporal-Order Judgments versus Those of Spatial-Location: Deactivation of Hippocampus May Facilitate Spatial Performance

ERIC Educational Resources Information Center

Rekkas, P. V.; Westerveld, M.; Skudlarski, P.; Zumer, J.; Pugh, K.; Spencer, D. D.; Constable, R. T.

2005-01-01

The retrieval of temporal-order versus spatial-location information was investigated using fMRI. The primary finding in the hippocampus proper, seen in region of interest analyses, was an increase in BOLD signal intensity for temporal retrieval, and a decrease in signal intensity for spatial retrieval, relative to baseline. The negative BOLD…

Blue Marble: Remote Characterization of Habitable Planets

NASA Technical Reports Server (NTRS)

Woolf, Neville; Lewis, Brian; Chartres, James; Genova, Anthony

2009-01-01

The study of the nature and distribution of habitable environments beyond the Solar System is a key area for Astrobiology research. At the present time, our Earth is the only habitable planet that can be characterized in the same way that we might characterize planets beyond the Solar System. Due to limitations in our current and near-future technology, it is likely that extra-solar planets will be observed as single-pixel objects. To understand this data, we must develop skills in analyzing and interpreting the radiation obtained from a single pixel. These skills must include the study of the time variation of the radiation, and the range of its photometric, spectroscopic and polarimetric properties. In addition, to understand whether we are properly analyzing the single pixel data, we need to compare it with a ground truth of modest resolution images in key spectral bands. This paper discusses the concept for a mission called Blue Marble that would obtain data of the Earth using a combination of spectropolarimetry, spectrophotometry, and selected band imaging. To obtain imagery of the proper resolution, it is desirable to place the Blue Marble spacecraft no closer than the outer region of cis-lunar space. This paper explores a conceptual mission design that takes advantage of low-cost launchers, bus designs and mission elements to provide a cost effective observing platform located at one of the stable Earth-moon Lagrangian points (L4, L5). The mission design allows for the development and use of novel technologies, such as a spinning moon sensor for attitude control, and leverages lessons-learned from previous low-cost spacecraft such as Lunar Prospector to yield a low-risk mission concept.

Flume experimentation and simulation of bedrock channel processes

NASA Astrophysics Data System (ADS)

Thompson, Douglas; Wohl, Ellen

Flume experiments can provide cost effective, physically manageable miniature representations of complex bedrock channels. The inherent change in scale in such experiments requires a corresponding change in the scale of the forces represented in the flume system. Three modeling approaches have been developed that either ignore the scaling effects, utilize the change in scaled forces, or assume similarity of process between scales. An understanding of the nonlinear influence of a change in scale on all the forces involved is important to correctly analyze model results. Similarly, proper design and operation of flume experiments requires knowledge of the fundamental components of flume systems. Entrance and exit regions of the flume are used to provide good experimental conditions in the measurement region of the flume where data are collected. To insure reproducibility, large-scale turbulence must be removed in the head of the flume and velocity profiles must become fully developed in the entrance region. Water-surface slope and flow acceleration effects from downstream water-depth control must also be isolated in the exit region. Statistical design and development of representative channel substrate also influence model results in these systems. With proper experimental design, flumes may be used to investigate bedrock channel hydraulics, sediment-transport relations, and morphologic evolution. In particular, researchers have successfully used flume experiments to demonstrate the importance of turbulence and substrate characteristics in bedrock channel evolution. Turbulence often operates in a self perpetuating fashion, can erode bedrock walls with clear water and increase the mobility of sediment particles. Bedrock substrate influences channel evolution by offering varying resistance to erosion, controlling the location or type of incision and modifying the local influence of turbulence. An increased usage of scaled flume models may help to clarify the remaining uncertainties involving turbulence, channel substrate and bedrock channel evolution.

Dynamics and control of high precision magnetically levitated vibration isolation systems

NASA Technical Reports Server (NTRS)

Youcef-Toumi, K.; Yeh, T-J.

1992-01-01

Vibration control of flexible structures has received a great deal of interest in recent years. Several authors have investigated this topic in the areas of robot manipulators, space structures, and flexible rotors. Key issues associated with the dynamics and control of vibration isolation systems are addressed. Among other important issues to consider in the control of such systems, the location and number of actuators and sensors are essential to effectively control and suppress vibration. We first address the selection of proper actuator and sensor locations leading to a controllable and observable system. The Rayleigh-Ritz modal analysis method is used to develop a lumped-parameter model of a flexible vibration isolation table top. This model is then used to investigate the system's controllability and observability including the coupling effects introduced by the magnetic bearing. This analysis results in necessary and sufficient conditions for proper selection of actuator and sensor locations. These locations are also important for both controller system's complexity and stability of point of views. A favorable pole-zero plot of the open loop transfer functions is presented. Necessary and sufficient conditions for reducing the controller complexity are derived. The results are illustrated by examples using approximate mode shape functions.

The optimization of design parameters for surge relief valve for pipeline systems

NASA Astrophysics Data System (ADS)

Kim, Hyunjun; Hur, Jisung; Kim, Sanghyun

2017-06-01

Surge is an abnormal pressure which induced by rapid changes of flow rate in pipeline systems. In order to protect pipeline system from the surge pressure, various hydraulic devices have been developed. Surge-relief valve(SRV) is one of the widely applied devices to control surge due to its feasibility in application, efficiency and cost-effectiveness. SRV is designed to automatically open under abnormal pressure and discharge the flow and makes pressure of the system drop to the allowable level. The performance of the SRV is influenced by hydraulics. According to previous studies, there are several affecting factors which determine performance of the PRV such as design parameters (e.g. size of the valve), system parameters (e.g. number of the valves and location of the valve), and operation parameters (e.g. set point and operation time). Therefore, the systematic consideration for factors affecting performance of SRV is required for the proper installation of SRV in the system. In this study, methodology for finding optimum parameters of the SRV is explored through the integration of Genetic Algorithm(GA) into surge analysis.

Design guidelines for avoiding thermo-acoustic oscillations in helium piping systems

DOE PAGES

Gupta, Prabhat Kumar; Rabehl, Roger

2015-04-02

Thermo-acoustic oscillations are a commonly observed phenomenon in helium cryogenic systems, especially in tubes connecting hot and cold areas. The open ends of these tubes are connected to the lower temperature (typically at 4.5 K), and the closed ends of these tubes are connected to the high temperature (300 K). Cryogenic instrumentation installations provide ideal conditions for these oscillations to occur due to the steep temperature gradient along the tubing. These oscillations create errors in measurements as well as an undesirable heat load to the system. The work presented here develops engineering guidelines to design oscillation-free helium piping. This workmore » also studies the effect of different piping inserts and shows how the proper geometrical combinations have to be chosen to avoid thermo-acoustic oscillations. The effect of an 80 K intercept is also studied and shows that thermo-oscillations can be dampened by placing the intercept at an appropriate location. As a result, the design of helium piping based on the present work is also verified with the experimental results available in open literature.« less

Shredded Waste Downdraft Gasifier for Overseas Contingency Operations Waste-to-Energy Conversion

DTIC Science & Technology

2015-06-01

results of the proposed experimental test plan and the design of a shredded waste WEC system in Task 5. A. Generators (Left) and Shredded...Shredded Waste 4 8.5 – 27.1 5.1.1.4 Wall Friction Tests In addition to a properly sized outlet, the design of a mass flow vessel must consider...consolidating pressures. 5.1.2.3 Wall Friction Tests In addition to a properly sized outlet, the design of a mass flow vessel must consider the

Physics of puffing and microexplosion of emulsion fuel droplets

NASA Astrophysics Data System (ADS)

Shinjo, J.; Xia, J.; Ganippa, L. C.; Megaritis, A.

2014-10-01

The physics of water-in-oil emulsion droplet microexplosion/puffing has been investigated using high-fidelity interface-capturing simulation. Varying the dispersed-phase (water) sub-droplet size/location and the initiation location of explosive boiling (bubble formation), the droplet breakup processes have been well revealed. The bubble growth leads to local and partial breakup of the parent oil droplet, i.e., puffing. The water sub-droplet size and location determine the after-puffing dynamics. The boiling surface of the water sub-droplet is unstable and evolves further. Finally, the sub-droplet is wrapped by boiled water vapor and detaches itself from the parent oil droplet. When the water sub-droplet is small, the detachment is quick, and the oil droplet breakup is limited. When it is large and initially located toward the parent droplet center, the droplet breakup is more extensive. For microexplosion triggered by the simultaneous growth of multiple separate bubbles, each explosion is local and independent initially, but their mutual interactions occur at a later stage. The degree of breakup can be larger due to interactions among multiple explosions. These findings suggest that controlling microexplosion/puffing is possible in a fuel spray, if the emulsion-fuel blend and the ambient flow conditions such as heating are properly designed. The current study also gives us an insight into modeling the puffing and microexplosion of emulsion droplets and sprays.

Floating Oil-Spill Containment Device

NASA Technical Reports Server (NTRS)

Jones, Jack A.

2012-01-01

Previous oil containment booms have an open top that allows natural gas to escape, and have significant oil leakage due to wave action. Also, a subsea pyramid oil trap exists, but cannot move relative to moving oil plumes from deepsea oil leaks. The solution is to have large, moveable oil traps. One version floats on the sea surface and has a flexible tarp cover and a lower weighted skirt to completely entrap the floating oil and natural gas. The device must have at least three sides with boats pulling at each apex, and sonar or other system to track the slowly moving oil plume, so that the boats can properly locate the booms. The oil trap device must also have a means for removal of the oil and the natural gas. A second design version has a flexible pyramid cover that is attached by lines to ballast on the ocean floor. This is similar to fixed, metal pyramid oil capture devices in the Santa Barbara Channel off the coast of California. The ballast lines for the improved design, however, would have winches that can move the pyramid to always be located above the oil and gas plume. A third design is a combination of the first two. It uses a submerged pyramid to trap oil, but has no anchor and uses boats to locate the trap. It has ballast weights located along the bottom of the tarp and/or at the corners of the trap. The improved floating oil-spill containment device has a large floating boom and weighted skirt surrounding the oil and gas entrapment area. The device is triangular (or more than three sides) and has a flexible tarp cover with a raised gas vent area. Boats pull on the apex of the triangles to maintain tension and to allow the device to move to optimum locations to trap oil and gas. The gas is retrieved from a higher buoyant part of the tarp, and oil is retrieved from the floating oil layer contained in the device. These devices can be operated in relatively severe weather, since waves will break over the devices without causing oil leaking. Also, natural gas is entrapped and can be retrieved. All designs can use sonar to locate the moving oil plume, and then be relocated by using boats or winches to move the oil trapping devices. These devices can be constructed of treated, non-permeable DuPont Kevlar cloth (or similar material).

Decoupled macro/micro-manipulator for fast and precise assembly operations: design and experiments

NASA Astrophysics Data System (ADS)

Hodac, Agathe; Siegwart, Roland Y.

1999-08-01

This paper presents a high performance single arm robot configuration, based on a macro-manipulator coupled with a micro-manipulator. The system is well suited to fast and precise positioning tasks for repetitive pick and place applications in the manufacturing industry. Firstly, the paper focuses on the design of the micro-manipulator, particularly on the selection of the proper micro-actuator type and location. We show that the micro-manipulator's design with an actuator placed between endpoint and ground and with a flexible suspension system can reduce the dynamic coupling between the macro-manipulator and the micro- manipulator. The overall system performance can then be improved. We describe two different designs of compact and fast micro-manipulators composed of voice coil actuators and a monolithic flexure suspension with notch hinges. Secondly, the paper presents a control strategy that allows both correction of possible misalignments of the end-effector relative to the target and compensation of tip oscillations. The dynamic interaction is analyzed and stability is verified. Finally, experimental results demonstrate significant improvements in acceleration, endpoint accuracy and settling time achieved by the novel configuration of the macro/micro-manipulator.

Study/Experimental/Research Design: Much More Than Statistics

PubMed Central

Knight, Kenneth L.

2010-01-01

Abstract Context: The purpose of study, experimental, or research design in scientific manuscripts has changed significantly over the years. It has evolved from an explanation of the design of the experiment (ie, data gathering or acquisition) to an explanation of the statistical analysis. This practice makes “Methods” sections hard to read and understand. Objective: To clarify the difference between study design and statistical analysis, to show the advantages of a properly written study design on article comprehension, and to encourage authors to correctly describe study designs. Description: The role of study design is explored from the introduction of the concept by Fisher through modern-day scientists and the AMA Manual of Style. At one time, when experiments were simpler, the study design and statistical design were identical or very similar. With the complex research that is common today, which often includes manipulating variables to create new variables and the multiple (and different) analyses of a single data set, data collection is very different than statistical design. Thus, both a study design and a statistical design are necessary. Advantages: Scientific manuscripts will be much easier to read and comprehend. A proper experimental design serves as a road map to the study methods, helping readers to understand more clearly how the data were obtained and, therefore, assisting them in properly analyzing the results. PMID:20064054

Studies on the psychosomatic functioning of ill-health according to Eastern and Western medicine. 1. Visual observation of the sublingual vein for early detection of vital energy stagnation and blood stasis.

PubMed

Takeichi, M; Sato, T

1999-01-01

Computer-assisted image analyses were performed on the tongue color of 95 medical students without previous history of blood stasis-related condition to clarify the mutual relationship of the color of the tongue proper, the coating, and sublingual vein. The location of the measurement for the tongue proper was the underside of the tongue, and location of the measurement for the tongue coating was the upper surface of the tongue. A linear correlation analysis showed a correlation for each of the different positions for the non-normalized red value and normalized blue value. This analysis also demonstrated a statistically-significant relationship between the tongue proper and the sublingual vein using Red-Green-Blue components and normalized Red-Green-Blue components (r = +0.670 - 0.817, p < 0.0001). The most significant correlation between the tongue proper and the sublingual vein was the normalized red value and the normalized Red-Green-Blue values for minimizing the range of the standard error of the mean (r = +0.745, p < 0.0001), although non-normalized blue had the highest correlation coefficient. Therefore, it seems reasonable to select those normalized red values for the comparison in the tongue color analysis. Correlation of the color between the sublingual vein and the tongue proper strongly suggests that inspection with the naked eye of the sublingual vein is useful for the early detection of vital energy stagnation and blood stasis. Also, because of its close relation to sustained chronic stress, changes in the sublingual vein might be available as one physiological parameter of a stress reaction.

Proper motions and membership probabilities of stars in the region of globular cluster NGC 6366

NASA Astrophysics Data System (ADS)

Sariya, Devesh P.; Yadav, R. K. S.

2015-12-01

Context. NGC 6366 is a metal-rich globular cluster that is relatively unstudied. It is a kinematically interesting cluster, reported as belonging to the slowly rotating halo system, which is unusual given its metallicity and spatial location in the Galaxy. Aims: The purpose of this research is to determine the relative proper motion and membership probability of the stars in the region of globular cluster NGC 6366. To target cluster members reliably during spectroscopic surveys without including field stars, a good proper motion and membership probability catalogue of NGC 6366 is needed. Methods: To derive relative proper motions, the archival data from the Wide Field Imager mounted on the ESO 2.2 m telescope have been reduced using a high precision astrometric software. The images used are in the B,V, and I photometric bands with an epoch gap of ~3.2 yr. The calibrated BVI magnitudes have been determined using recent data for secondary standard stars. Results: We determined relative proper motions and cluster membership probabilities for 2530 stars in the field of globular cluster NGC 6366. The median proper motion rms errors for stars brighter than V ~ 18 mag is ~2 mas yr-1, which gradually increases to ~5 mas yr-1 for stars having magnitudes V ~ 20 mag. Based on the membership catalogue, we checked the membership status of the X-ray sources and variable stars of NGC 6366 mentioned in the literature. We also provide the astronomical community with an electronic catalogue that includes B, V, and I magnitudes; relative proper motions; and membership probabilities of the stars in the region of NGC 6366. Based on observations with the MPG/ESO 2.2 m and ESO/VLT telescopes, located at La Silla and Paranal Observatory, Chile, under DDT programs 164.O-0561(F), 71.D-0220(A) and the archive material.Full Table 4 is only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/584/A59

Mars Tumbleweed Simulation Using Singular Perturbation Theory

NASA Technical Reports Server (NTRS)

Raiszadeh, Behzad; Calhoun, Phillip

2005-01-01

The Mars Tumbleweed is a new surface rover concept that utilizes Martian winds as the primary source of mobility. Several designs have been proposed for the Mars Tumbleweed, all using aerodynamic drag to generate force for traveling about the surface. The Mars Tumbleweed, in its deployed configuration, must be large and lightweight to provide the ratio of drag force to rolling resistance necessary to initiate motion from the Martian surface. This paper discusses the dynamic simulation details of a candidate Tumbleweed design. The dynamic simulation model must properly evaluate and characterize the motion of the tumbleweed rover to support proper selection of system design parameters. Several factors, such as model flexibility, simulation run times, and model accuracy needed to be considered in modeling assumptions. The simulation was required to address the flexibility of the rover and its interaction with the ground, and properly evaluate its mobility. Proper assumptions needed to be made such that the simulated dynamic motion is accurate and realistic while not overly burdened by long simulation run times. This paper also shows results that provided reasonable correlation between the simulation and a drop/roll test of a tumbleweed prototype.

75 FR 54587 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-08

...) Whether the collection of information is necessary for the proper performance of the functions of the..., phone number, farm location, race, ethnicity and gender from the Minority Farm Register permission form...

Genetics Home Reference: triple A syndrome

MedlinePlus

... understood. Within cells, ALADIN is found in the nuclear envelope, the structure that surrounds the nucleus and ... protein from reaching its proper location in the nuclear envelope. The absence of ALADIN in the nuclear ...

Mitigated FPGA design of multi-gigabit transceivers for application in high radiation environments of High Energy Physics experiments

DOE PAGES

Brusati, M.; Camplani, A.; Cannon, M.; ...

2017-02-20

SRAM-ba8ed Field Programmable Gate Array (FPGA) logic devices arc very attractive in applications where high data throughput is needed, such as the latest generation of High Energy Physics (HEP) experiments. FPGAs have been rarely used in such experiments because of their sensitivity to radiation. The present paper proposes a mitigation approach applied to commercial FPGA devices to meet the reliability requirements for the front-end electronics of the Liquid Argon (LAr) electromagnetic calorimeter of the ATLAS experiment, located at CERN. Particular attention will be devoted to define a proper mitigation scheme of the multi-gigabit transceivers embedded in the FPGA, which ismore » a critical part of the LAr data acquisition chain. A demonstrator board is being developed to validate the proposed methodology. :!\\litigation techniques such as Triple Modular Redundancy (T:t\\IR) and scrubbing will be used to increase the robustness of the design and to maximize the fault tolerance from Single-Event Upsets (SEUs).« less

The stem cell laboratory: design, equipment, and oversight.

PubMed

Wesselschmidt, Robin L; Schwartz, Philip H

2011-01-01

This chapter describes some of the major issues to be considered when setting up a laboratory for the culture of human pluripotent stem cells (hPSCs). The process of establishing a hPSC laboratory can be divided into two equally important parts. One is completely administrative and includes developing protocols, seeking approval, and establishing reporting processes and documentation. The other part of establishing a hPSC laboratory involves the physical plant and includes design, equipment and personnel. Proper planning of laboratory operations and proper design of the physical layout of the stem cell laboratory so that meets the scope of planned operations is a major undertaking, but the time spent upfront will pay long-term returns in operational efficiency and effectiveness. A well-planned, organized, and properly equipped laboratory supports research activities by increasing efficiency and reducing lost time and wasted resources.

Evaluation of Temperature Gradient in Advanced Automated Directional Solidification Furnace (AADSF) by Numerical Simulation

NASA Technical Reports Server (NTRS)

Bune, Andris V.; Gillies, Donald C.; Lehoczky, Sandor L.

1996-01-01

A numerical model of heat transfer using combined conduction, radiation and convection in AADSF was used to evaluate temperature gradients in the vicinity of the crystal/melt interface for variety of hot and cold zone set point temperatures specifically for the growth of mercury cadmium telluride (MCT). Reverse usage of hot and cold zones was simulated to aid the choice of proper orientation of crystal/melt interface regarding residual acceleration vector without actual change of furnace location on board the orbiter. It appears that an additional booster heater will be extremely helpful to ensure desired temperature gradient when hot and cold zones are reversed. Further efforts are required to investigate advantages/disadvantages of symmetrical furnace design (i.e. with similar length of hot and cold zones).

Ultrasonic humidification for telecommunications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Longo, F.

1994-03-01

This article examines two installations which demonstrate that ultrasonic humidification is an excellent option for large-scale commercial installations. Many existing telephone switching centers constructed 20 to 30 years ago were equipped with electro-mechanical switching equipment that was not sensitive to humidity. Today's sophisticated solid-state telecommunications equipment requires specific levels of relative humidity to operate properly. Over the last several years, Einhorn Yaffee Prescott (formerly Rose Beaton + Rose) designed two of the largest ultrasonic humidification systems at telecommunications buildings located in Cheshire, Conn., and White Plains, N.Y. The Cheshire project was a retrofit to the existing system in a 1960smore » building; the White Plains project involved an upgrade to a totally new air handling system, including an ultrasonic humidification component, in a 1950s building.« less

Genetic Algorithm Approaches for Actuator Placement

NASA Technical Reports Server (NTRS)

Crossley, William A.

2000-01-01

This research investigated genetic algorithm approaches for smart actuator placement to provide aircraft maneuverability without requiring hinged flaps or other control surfaces. The effort supported goals of the Multidisciplinary Design Optimization focus efforts in NASA's Aircraft au program. This work helped to properly identify various aspects of the genetic algorithm operators and parameters that allow for placement of discrete control actuators/effectors. An improved problem definition, including better definition of the objective function and constraints, resulted from this research effort. The work conducted for this research used a geometrically simple wing model; however, an increasing number of potential actuator placement locations were incorporated to illustrate the ability of the GA to determine promising actuator placement arrangements. This effort's major result is a useful genetic algorithm-based approach to assist in the discrete actuator/effector placement problem.

Grid Task Execution

NASA Technical Reports Server (NTRS)

Hu, Chaumin

2007-01-01

IPG Execution Service is a framework that reliably executes complex jobs on a computational grid, and is part of the IPG service architecture designed to support location-independent computing. The new grid service enables users to describe the platform on which they need a job to run, which allows the service to locate the desired platform, configure it for the required application, and execute the job. After a job is submitted, users can monitor it through periodic notifications, or through queries. Each job consists of a set of tasks that performs actions such as executing applications and managing data. Each task is executed based on a starting condition that is an expression of the states of other tasks. This formulation allows tasks to be executed in parallel, and also allows a user to specify tasks to execute when other tasks succeed, fail, or are canceled. The two core components of the Execution Service are the Task Database, which stores tasks that have been submitted for execution, and the Task Manager, which executes tasks in the proper order, based on the user-specified starting conditions, and avoids overloading local and remote resources while executing tasks.

Effective protective surveillance for waterside-located chemical plants

NASA Astrophysics Data System (ADS)

Love, John; Van Dover, Doug

2006-05-01

Millions of citizens live and work in the dangerous proximity of chemical plants, at ports and along waterways, which are under-protected and whose security is under-regulated, according to findings of the Congressional Research Service (CRS). There is a new and intense focus on the security of the nation's critical infrastructure. Thanks to recent philosophy and policy shifts within our federal government, the alarming situations in which we find ourselves will be mitigated somewhat a) by setting priorities based on proper threat analysis that considers event likelihoods and consequential impacts, and b) by employing effective systems design and engineering that will make it possible to address the highest priority threats with affordable solutions. It is the latter concern that we address, especially as it is relates to design and engineering of solutions for maintaining vigilance night and day. We begin by reviewing the nature of the facilities we wish to protect, our assumptions, and an accepted framework for analysis. Next we outline a hypothetical design case involving a representative facility and a plausible design basis threat. We then derive requirements for surveillance and examine the interrelationships among key design variables. Finally, we describe a solution involving multiple sensor types coupled with intelligent video. The end result is a significant increase in interdiction probability with a minimum of required assets.

The correlation between body mass index, limb circumferences and blood pressure cuff fit in bariatric surgical patients.

PubMed

Schumann, R; Alyamani, O; Viswanath, A; Bonney, I

2016-01-01

The purpose of this study was to determine the correlation between body mass index (BMI) and upper and lower arm as well as lower leg circumferences and the frequency of correct blood pressure (BP) cuff fit. We explored recommendations for the most likely BP cuff size and location for the three BMI categories. Following IRB approval we retrospectively analyzed a research database of bariatric surgical patients with a BMI of ≥40 kg/m(2). Data included patients' characteristics, upper and lower arm as well as lower leg circumferences. Patients were divided into three groups based on BMI (kg/m(2), Group I: <45, Group II: 45-55, and Group III: >55). Appropriate cuff fit using a standard or large adult BP cuff (CRITIKON(®), GE Healthcare, Waukesha, Wisconsin, USA) on the upper and lower arm, and lower leg was determined. We analyzed the percent proportion of proper cuff fit for cuff sizes and locations between groups using appropriate nonparametric testing. Limb circumference correlated significantly with BMI (P = 0.01), and the upper arm correlated most closely (r = 0.76). A standard adult BP cuff on the lower arm fit properly in >90% and >80% and in Groups I and II, respectively. A large cuff on the lower arm was appropriate in 87% of Group III. In two participants, a large cuff fit properly on the lower leg. Limb circumference significantly correlated with BMI. Recommendations for proper cuff fit in different BMI categories can be made.

Visual analytics of geo-social interaction patterns for epidemic control.

PubMed

Luo, Wei

2016-08-10

Human interaction and population mobility determine the spatio-temporal course of the spread of an airborne disease. This research views such spreads as geo-social interaction problems, because population mobility connects different groups of people over geographical locations via which the viruses transmit. Previous research argued that geo-social interaction patterns identified from population movement data can provide great potential in designing effective pandemic mitigation. However, little work has been done to examine the effectiveness of designing control strategies taking into account geo-social interaction patterns. To address this gap, this research proposes a new framework for effective disease control; specifically this framework proposes that disease control strategies should start from identifying geo-social interaction patterns, designing effective control measures accordingly, and evaluating the efficacy of different control measures. This framework is used to structure design of a new visual analytic tool that consists of three components: a reorderable matrix for geo-social mixing patterns, agent-based epidemic models, and combined visualization methods. With real world human interaction data in a French primary school as a proof of concept, this research compares the efficacy of vaccination strategies between the spatial-social interaction patterns and the whole areas. The simulation results show that locally targeted vaccination has the potential to keep infection to a small number and prevent spread to other regions. At some small probability, the local control strategies will fail; in these cases other control strategies will be needed. This research further explores the impact of varying spatial-social scales on the success of local vaccination strategies. The results show that a proper spatial-social scale can help achieve the best control efficacy with a limited number of vaccines. The case study shows how GS-EpiViz does support the design and testing of advanced control scenarios in airborne disease (e.g., influenza). The geo-social patterns identified through exploring human interaction data can help target critical individuals, locations, and clusters of locations for disease control purposes. The varying spatial-social scales can help geographically and socially prioritize limited resources (e.g., vaccines).

Focused-based multifractal analysis of the wake in a wind turbine array utilizing proper orthogonal decomposition

NASA Astrophysics Data System (ADS)

Kadum, Hawwa; Ali, Naseem; Cal, Raúl

2016-11-01

Hot-wire anemometry measurements have been performed on a 3 x 3 wind turbine array to study the multifractality of the turbulent kinetic energy dissipations. A multifractal spectrum and Hurst exponents are determined at nine locations downstream of the hub height, and bottom and top tips. Higher multifractality is found at 0.5D and 1D downstream of the bottom tip and hub height. The second order of the Hurst exponent and combination factor show an ability to predict the flow state in terms of its development. Snapshot proper orthogonal decomposition is used to identify the coherent and incoherent structures and to reconstruct the stochastic velocity using a specific number of the POD eigenfunctions. The accumulation of the turbulent kinetic energy in top tip location exhibits fast convergence compared to the bottom tip and hub height locations. The dissipation of the large and small scales are determined using the reconstructed stochastic velocities. The higher multifractality is shown in the dissipation of the large scale compared to small-scale dissipation showing consistency with the behavior of the original signals.

Locating underwater objects. [technology transfer

NASA Technical Reports Server (NTRS)

Grice, C. F.

1974-01-01

Underwater search operations are considered to be engineering and operational problems. A process for proper definition of the problem and selection of instrumentation and operational procedures is described. An outline of underwater search instrumentation and techniques is given.

Office Building Occupant's Guide to Indoor Air Quality

MedlinePlus

... physical aspects of the workplace: location, work environment, availability of natural light and the aesthetics of office ... promptly and properly. Dispose of garbage in appropriate containers that are emptied daily to prevent odors and ...

Factors for improved fish passage waterway construction.

DOT National Transportation Integrated Search

2011-06-01

Streambeds are important fish passageways in Oregon; they provide for the necessary habitats and spawning cycles of a healthy fish population. Oregon state law requires that hydraulic structures located in water properly provide fish passage. Increas...

Identification of stars in a J1744.0 star catalogue Yixiangkaocheng

NASA Astrophysics Data System (ADS)

Ahn, S.-H.

2012-05-01

The stars in the Chinese star catalogue, Yixiangkaocheng, which were edited by the Jesuit astronomer Kögler in AD 1744 and published in AD 1756, are identified with their counterparts in the Hipparcos catalogue. The equinox of the catalogue is confirmed to be J1744.0. By considering the precession of equinox, proper motions and nutation, the star closest to the location of each star in Yixiangkaocheng, having a proper magnitude, is selected as the corresponding identified star. I identified 2848 stars and 13 nebulosities out of 3083 objects in Yixiangkaocheng, and so the identification rate reached 92.80 per cent. I find that the magnitude classification system in Yixiangkaocheng agrees with the modern magnitude system. The catalogue includes dim stars, whose visual magnitudes are larger than 7, but most of these stars have Flamsteed designations. I find that the stars whose declination is lower than -30° have relatively larger offsets and different systematic behaviour from other stars. This indicates that there might be two different sources of stars in Yixiangkaocheng. In particular, I find that μ1 Sco and γ1 Sgr approximately mark the boundary between two different source catalogues. The observer's location, as estimated from these facts, agrees with the latitude of Greenwich where Flamsteed made his observations. The positional offsets between the Yixiangkaocheng stars and the Hipparcos stars are 0.6 arcmin, which implies that the source catalogue of stars with δ > -30° must have come from telescopic observations. Nebulosities in Yixiangkaocheng are identified with a few double stars, o Cet (the variable star, Mira), the Andromeda galaxy, ω Cen and NGC6231. These entities are associated with listings in Halley's Catalogue of the Southern Stars of AD 1679 as well as Flamsteed's catalogue of AD 1690.

Explicit parametric solutions of lattice structures with proper generalized decomposition (PGD) - Applications to the design of 3D-printed architectured materials

NASA Astrophysics Data System (ADS)

Sibileau, Alberto; Auricchio, Ferdinando; Morganti, Simone; Díez, Pedro

2018-01-01

Architectured materials (or metamaterials) are constituted by a unit-cell with a complex structural design repeated periodically forming a bulk material with emergent mechanical properties. One may obtain specific macro-scale (or bulk) properties in the resulting architectured material by properly designing the unit-cell. Typically, this is stated as an optimal design problem in which the parameters describing the shape and mechanical properties of the unit-cell are selected in order to produce the desired bulk characteristics. This is especially pertinent due to the ease manufacturing of these complex structures with 3D printers. The proper generalized decomposition provides explicit parametic solutions of parametric PDEs. Here, the same ideas are used to obtain parametric solutions of the algebraic equations arising from lattice structural models. Once the explicit parametric solution is available, the optimal design problem is a simple post-process. The same strategy is applied in the numerical illustrations, first to a unit-cell (and then homogenized with periodicity conditions), and in a second phase to the complete structure of a lattice material specimen.

Reliable B Cell Epitope Predictions: Impacts of Method Development and Improved Benchmarking

PubMed Central

Kringelum, Jens Vindahl; Lundegaard, Claus; Lund, Ole; Nielsen, Morten

2012-01-01

The interaction between antibodies and antigens is one of the most important immune system mechanisms for clearing infectious organisms from the host. Antibodies bind to antigens at sites referred to as B-cell epitopes. Identification of the exact location of B-cell epitopes is essential in several biomedical applications such as; rational vaccine design, development of disease diagnostics and immunotherapeutics. However, experimental mapping of epitopes is resource intensive making in silico methods an appealing complementary approach. To date, the reported performance of methods for in silico mapping of B-cell epitopes has been moderate. Several issues regarding the evaluation data sets may however have led to the performance values being underestimated: Rarely, all potential epitopes have been mapped on an antigen, and antibodies are generally raised against the antigen in a given biological context not against the antigen monomer. Improper dealing with these aspects leads to many artificial false positive predictions and hence to incorrect low performance values. To demonstrate the impact of proper benchmark definitions, we here present an updated version of the DiscoTope method incorporating a novel spatial neighborhood definition and half-sphere exposure as surface measure. Compared to other state-of-the-art prediction methods, Discotope-2.0 displayed improved performance both in cross-validation and in independent evaluations. Using DiscoTope-2.0, we assessed the impact on performance when using proper benchmark definitions. For 13 proteins in the training data set where sufficient biological information was available to make a proper benchmark redefinition, the average AUC performance was improved from 0.791 to 0.824. Similarly, the average AUC performance on an independent evaluation data set improved from 0.712 to 0.727. Our results thus demonstrate that given proper benchmark definitions, B-cell epitope prediction methods achieve highly significant predictive performances suggesting these tools to be a powerful asset in rational epitope discovery. The updated version of DiscoTope is available at www.cbs.dtu.dk/services/DiscoTope-2.0. PMID:23300419

High-Voltage, Low-Power BNC Feedthrough Terminator

NASA Technical Reports Server (NTRS)

Bearden, Douglas

2012-01-01

This innovation is a high-voltage, lowpower BNC (Bayonet Neill-Concelman) feedthrough that enables the user to terminate an instrumentation cable properly while connected to a high voltage, without the use of a voltage divider. This feedthrough is low power, which will not load the source, and will properly terminate the instrumentation cable to the instrumentation, even if the cable impedance is not constant. The Space Shuttle Program had a requirement to measure voltage transients on the orbiter bus through the Ground Lightning Measurement System (GLMS). This measurement has a bandwidth requirement of 1 MHz. The GLMS voltage measurement is connected to the orbiter through a DC panel. The DC panel is connected to the bus through a nonuniform cable that is approximately 75 ft (approximately equal to 23 m) long. A 15-ft (approximately equal to 5-m), 50-ohm triaxial cable is connected between the DC panel and the digitizer. Based on calculations and simulations, cable resonances and reflections due to mismatched impedances of the cable connecting the orbiter bus and the digitizer causes the output not to reflect accurately what is on the bus. A voltage divider at the DC panel, and terminating the 50-ohm cable properly, would eliminate this issue. Due to implementation issues, an alternative design was needed to terminate the cable properly without the use of a voltage divider. Analysis shows how the cable resonances and reflections due to the mismatched impedances of the cable connecting the orbiter bus and the digitizer causes the output not to reflect accurately what is on the bus. After simulating a dampening circuit located at the digitizer, simulations were performed to show how the cable resonances were dampened and the accuracy was improved significantly. Test cables built to verify simulations were accurate. Since the dampening circuit is low power, it can be packaged in a BNC feedthrough.

Aerodynamic design of gas and aerosol samplers for aircraft

NASA Technical Reports Server (NTRS)

Soderman, Paul T.; Hazen, Nathan L.; Brune, William H.

1991-01-01

The aerodynamic design of airborne probes for the capture of air and aerosols is discussed. Emphasis is placed on the key parameters that affect proper sampling, such as inlet-lip design, internal duct components for low pressure drop, and exhaust geometry. Inlet designs that avoid sonic flow conditions on the lip and flow separation in the duct are shown. Cross-stream velocities of aerosols are expressed in terms of droplet density and diameter. Flow curvature, which can cause aerosols to cross streamlines and impact on probe walls, can be minimized by means of a proper inlet shape and proper probe orientation, and by avoiding bends upstream of the test section. A NASA panel code called PMARC was used successfully to compute streamlines around aircraft and probes, as well as to compute to local velocity and pressure distributions in inlets. A NACA 1-series inlet with modified lip radius was used for the airborne capture of stratospheric chlorine monoxide at high altitude and high flight speed. The device has a two-stage inlet that decelerates the inflow with little disturbance to the flow through the test section. Diffuser design, exhaust hood design, valve loss, and corner vane geometry are discussed.

The Stem Cell Laboratory: Design, Equipment, and Oversight

PubMed Central

Wesselschmidt, Robin L.; Schwartz, Philip H.

2013-01-01

This chapter describes some of the major issues to be considered when setting up a laboratory for the culture of human pluripotent stem cells (hPSCs). The process of establishing a hPSC laboratory can be divided into two equally important parts. One is completely administrative and includes developing protocols, seeking approval, and establishing reporting processes and documentation. The other part of establishing a hPSC laboratory involves the physical plant and includes design, equipment and personnel. Proper planning of laboratory operations and proper design of the physical layout of the stem cell laboratory so that meets the scope of planned operations is a major undertaking, but the time spent upfront will pay long-term returns in operational efficiency and effectiveness. A well-planned, organized, and properly equipped laboratory supports research activities by increasing efficiency and reducing lost time and wasted resources. PMID:21822863

System and method for 2D workpiece alignment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weaver, William T.; Carlson, Charles T.; Smith, Scott A.

2015-07-14

A carrier capable of holding one or more workpieces is disclosed. The carrier includes movable projections located along the sides of each cell in the carrier. This carrier, in conjunction with a separate alignment apparatus, aligns each workpiece within its respective cell against several alignment pins, using a multiple step alignment process to guarantee proper positioning of the workpiece in the cell. First, the workpieces are moved toward one side of the cell. Once the workpieces have been aligned against this side, the workpieces are then moved toward an adjacent orthogonal side such that the workpieces are aligned to twomore » sides of the cell. Once aligned, the workpiece is held in place by the projections located along each side of each cell. In addition, the alignment pins are also used to align the associated mask, thereby guaranteeing that the mask is properly aligned to the workpiece.« less

Frontal Representation as a Metric of Model Performance

NASA Astrophysics Data System (ADS)

Douglass, E.; Mask, A. C.

2017-12-01

Representation of fronts detected by altimetry are used to evaluate the performance of the HYCOM global operational product. Fronts are detected and assessed in daily alongtrack altimetry. Then, modeled sea surface height is interpolated to the locations of the alongtrack observations, and the same frontal detection algorithm is applied to the interpolated model output. The percentage of fronts found in the altimetry and replicated in the model gives a score (0-100) that assesses the model's ability to replicate fronts in the proper location with the proper orientation. Further information can be obtained from determining the number of "extra" fronts found in the model but not in the altimetry, and from assessing the horizontal and vertical dimensions of the front in the model as compared to observations. Finally, the sensitivity of this metric to choices regarding the smoothing of noisy alongtrack altimetry observations, and to the minimum size of fronts being analyzed, is assessed.

STS-61 crew utilizing Virtual Reality in training for HST repair mission

NASA Image and Video Library

1993-06-11

Astronaut Jeffrey A. Hoffman, one of four crewmembers for STS-61 that will conduct scheduled spacewalks during the flight, wears a special helmet and gloves designed to assist in proper positioning near the telescope while on the end of the robot arm. Crewmembers are utilizing a new virtual reality training aid which assists in refining positioning patterns for Space Shuttle Endeavour's Remote Manipulator System (RMS) (36890); Astronaut Claude Nicollier looks at a computer display of the Shuttle's robot arm movements as Thomas D. Akers and Kathryn C. Thornton, mission specialists look on. Nicollier will be responsible for maneuvering the astronauts while they stand in a foot restraint on the end of the RMS arm (36891,36894); Hoffman wears a special helmet and gloves designed to assist in proper positioning near the telescope while on the end of the robot arm (35892); Nicollier looks at a computer display of the Shuttle's robot arm movements as Akers looks on (36893); While (l-r) Astronauts Kenneth Bowersox, Kathryn Thornton, Richard O. Covey and Thomas D. Akers watch, Nicollier moves the Robot arm to desired locations in the Shuttle's payload bay using the Virtual Reality program (36895); Bowersox takes his turn maneuvering the RMS while mission specialist Hoffman, wearing the Virtual Reality helmet, follows his own progress on the end of the robot arm. Crewmembers participating during the training session are (l-r) Astronauts Akers, Hoffman, Bowersox, Nicollier, Covey, and Thornton. In the background, David Homan, an engineer in the JSC Engineering Directorate's Automation and Robotics Division, looks on (36896).

All-Direction Random Routing for Source-Location Privacy Protecting against Parasitic Sensor Networks.

PubMed

Wang, Na; Zeng, Jiwen

2017-03-17

Wireless sensor networks are deployed to monitor the surrounding physical environments and they also act as the physical environments of parasitic sensor networks, whose purpose is analyzing the contextual privacy and obtaining valuable information from the original wireless sensor networks. Recently, contextual privacy issues associated with wireless communication in open spaces have not been thoroughly addressed and one of the most important challenges is protecting the source locations of the valuable packages. In this paper, we design an all-direction random routing algorithm (ARR) for source-location protecting against parasitic sensor networks. For each package, the routing process of ARR is divided into three stages, i.e., selecting a proper agent node, delivering the package to the agent node from the source node, and sending it to the final destination from the agent node. In ARR, the agent nodes are randomly chosen in all directions by the source nodes using only local decisions, rather than knowing the whole topology of the networks. ARR can control the distributions of the routing paths in a very flexible way and it can guarantee that the routing paths with the same source and destination are totally different from each other. Therefore, it is extremely difficult for the parasitic sensor nodes to trace the packages back to the source nodes. Simulation results illustrate that ARR perfectly confuses the parasitic nodes and obviously outperforms traditional routing-based schemes in protecting source-location privacy, with a marginal increase in the communication overhead and energy consumption. In addition, ARR also requires much less energy than the cloud-based source-location privacy protection schemes.

Automated location detection of injection site for preclinical stereotactic neurosurgery procedure

NASA Astrophysics Data System (ADS)

Abbaszadeh, Shiva; Wu, Hemmings C. H.

2017-03-01

Currently, during stereotactic neurosurgery procedures, the manual task of locating the proper area for needle insertion or implantation of electrode/cannula/optic fiber can be time consuming. The requirement of the task is to quickly and accurately find the location for insertion. In this study we investigate an automated method to locate the entry point of region of interest. This method leverages a digital image capture system, pattern recognition, and motorized stages. Template matching of known anatomical identifiable regions is used to find regions of interest (e.g. Bregma) in rodents. For our initial study, we tackle the problem of automatically detecting the entry point.

Planning for hazardous campus waste collection.

PubMed

Liu, Kun-Hsing; Shih, Shao-Yang; Kao, Jehng-Jung

2011-05-15

This study examines a procedure developed for planning a nation-wide hazardous campus waste (HCW) collection system. Alternative HCW plans were designed for different collection frequencies, truckloads, storage limits, and also for establishing an additional transfer station. Two clustering methods were applied to group adjacent campuses into clusters based on their locations, HCW quantities, the type of vehicles used and collection frequencies. Transportation risk, storage risk, and collection cost are the major criteria used to evaluate the feasibility of each alternative. Transportation risk is determined based on the accident rates for each road type and collection distance, while storage risk is calculated by estimating the annual average HCW quantity stored on campus. Alternatives with large trucks can reduce both transportation risk and collection cost, but their storage risks would be significantly increased. Alternatives that collect neighboring campuses simultaneously can effectively reduce storage risks as well as collection cost if the minimum quantity to collect for each group of neighboring campuses can be properly set. The three transfer station alternatives evaluated for northern Taiwan are cost effective and involve significantly lower transportation risk. The procedure proposed is expected to facilitate decision making and to support analyses for formulating a proper nation-wide HCW collection plan. Copyright © 2011 Elsevier B.V. All rights reserved.

Software solutions manage the definition, operation, maintenance and configuration control of the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dobson, D; Churby, A; Krieger, E

2011-07-25

The National Ignition Facility (NIF) is the world's largest laser composed of millions of individual parts brought together to form one massive assembly. Maintaining control of the physical definition, status and configuration of this structure is a monumental undertaking yet critical to the validity of the shot experiment data and the safe operation of the facility. The NIF business application suite of software provides the means to effectively manage the definition, build, operation, maintenance and configuration control of all components of the National Ignition Facility. State of the art Computer Aided Design software applications are used to generate a virtualmore » model and assemblies. Engineering bills of material are controlled through the Enterprise Configuration Management System. This data structure is passed to the Enterprise Resource Planning system to create a manufacturing bill of material. Specific parts are serialized then tracked along their entire lifecycle providing visibility to the location and status of optical, target and diagnostic components that are key to assessing pre-shot machine readiness. Nearly forty thousand items requiring preventive, reactive and calibration maintenance are tracked through the System Maintenance & Reliability Tracking application to ensure proper operation. Radiological tracking applications ensure proper stewardship of radiological and hazardous materials and help provide a safe working environment for NIF personnel.« less

International Space Station USOS Potable Water Dispenser Development

NASA Technical Reports Server (NTRS)

Shaw, Laura A.; Barreda, Jose L.

2008-01-01

The International Space Station (ISS) Russian Segment currently provides potable water dispensing capability for crewmember food and beverage rehydration. All ISS crewmembers rehydrate Russian and U.S. style food packages from this location. A new United States On-orbit Segment (USOS) Potable Water Dispenser (PWD) is under development. This unit will provide additional potable water dispensing capability to support an onorbit crew of six. The PWD is designed to provide incremental quantities of hot and ambient temperature potable water to U.S. style food packages. It will receive iodinated water from the Fuel Cell Water Bus in the U.S. Laboratory element. The unit will provide potable-quality water, including active removal of biocidal iodine prior to dispensing. A heater assembly contained within the unit will be able to supply up to 2.0 liters of hot water (65 to 93oC) every thirty minutes. This quantity will allow three to four crewmembers to rehydrate their food and beverages from this location during a single meal. The unit is designed to remain functional for up to ten years with replacement of limited life items such as filters. It will be the size of two stacked Shuttle Middeck lockers (approximately the size of two small suitcases) and integrated into a science payload rack in the U.S. Laboratory element. Providing potable-quality water at the proper temperature for food and beverage reconstitution is critical to maintaining crew health and well-being. The numerous engineering challenges as well as human factors and safety considerations during the concept, design, and prototyping are outlined in this paper.

A design strategy for the use of vortex generators to manage inlet-engine distortion using computational fluid dynamics

NASA Technical Reports Server (NTRS)

Anderson, Bernhard H.; Levy, Ralph

1991-01-01

A reduced Navier-Stokes solution technique was successfully used to design vortex generator installations for the purpose of minimizing engine face distortion by restructuring the development of secondary flow that is induced in typical 3-D curved inlet ducts. The results indicate that there exists an optimum axial location for this installation of corotating vortex generators, and within this configuration, there exists a maximum spacing between generator blades above which the engine face distortion increases rapidly. Installed vortex generator performance, as measured by engine face circumferential distortion descriptors, is sensitive to Reynolds number and thereby the generator scale, i.e., the ratio of generator blade height to local boundary layer thickness. Installations of corotating vortex generators work well in terms of minimizing engine face distortion within a limited range of generator scales. Hence, the design of vortex generator installations is a point design, and all other conditions are off design. In general, the loss levels associated with a properly designed vortex generator installation are very small; thus, they represent a very good method to manage engine face distortion. This study also showed that the vortex strength, generator scale, and secondary flow field structure have a complicated and interrelated influence over engine face distortion, over and above the influence of the initial arrangement of generators.

SPod Progress Summary Slides | Science Inventory | US EPA

EPA Pesticide Factsheets

This presentation describes the draft “open source” design package for the SPod fenceline sensor. The SPod is a low cost, solar-powered system that combines wind field and air pollutant concentration measurements to detect emission plumes and help locate the source of emissions. The current design works only in “near-fenceline” applications where localized source emission plumes may be present. The SPod uses data analysis software (described elsewhere) to separate baseline drift from the plume signal of interest. This software is necessary for proper operation of the SPod. Because the SPod is designed to detect source emissions plumes, it is not useful for ambient applications large distances away from sources. The current SPod detects a subset of air pollutants that can be ionized with a 10.6 eV photoionization detector (PID). In the future, other air pollutant sensors may be used. The purpose of this presentation and related postings is to advance design concepts in the low-cost fenceline sensor area with any interested parties. The SPod is a work in progress with continued advances incorporated on an ongoing basis. This document is posted on an EPA share drive along with other information that describes the use operation and limitations of the SPod. These slides summarize the SPod design, purpose, and progress as of June, 2016. These slides will be posted on the EPA SPod Share Site along with design information and other materials that communicat

Proper motion separation of Be stars in the Milky Way and the Magellanic Clouds

NASA Astrophysics Data System (ADS)

Vieira, K.; García, A.; Sabogal, B.

2018-01-01

We present a proper motion investigation of a sample of Be stars candidates towards the Large Magellanic Cloud (LMC), which has resulted in the identification of two separate populations, in the Galactic foreground and in the Magellanic background. OGLE BVI and 2MASS JHK photometry were used with the SPM4 proper motions to discriminate the different populations located towards the LMC. Two populations with distinctive infrared colours and noticeable different kinematics were found, the bluer sample is consistent with being in the LMC and the redder one with belonging to the Milky Way (MW) disk. This settles the nature of the redder sample which had been described in previous publications as a possible unknown subclass of stars among the Be candidates in the LMC.

Effects of the location of distal histidine in the reaction of myoglobin with hydrogen peroxide.

PubMed

Matsui, T; Ozaki, S i; Liong, E; Phillips, G N; Watanabe, Y

1999-01-29

To clarify how the location of distal histidine affects the activation process of H2O2 by heme proteins, we have characterized reactions with H2O2 for the L29H/H64L and F43H/H64L mutants of sperm whale myoglobin (Mb), designed to locate the histidine farther from the heme iron. Whereas the L29H/H64L double substitution retarded the reaction with H2O2, an 11-fold rate increase versus wild-type Mb was observed for the F43H/H64L mutant. The Vmax values for 1-electron oxidations by the myoglobins correlate well with the varied reactivities with H2O2. The functions of the distal histidine as a general acid-base catalyst were examined based on the reactions with cumene hydroperoxide and cyanide, and only the histidine in F43H/H64L Mb was suggested to facilitate heterolysis of the peroxide bond. The x-ray crystal structures of the mutants confirmed that the distal histidines in F43H/H64L Mb and peroxidase are similar in distance from the heme iron, whereas the distal histidine in L29H/H64L Mb is located too far to enhance heterolysis. Our results indicate that the proper positioning of the distal histidine is essential for the activation of H2O2 by heme enzymes.

Attention to baseline: does orienting visuospatial attention really facilitate target detection?

PubMed

Albares, Marion; Criaud, Marion; Wardak, Claire; Nguyen, Song Chi Trung; Ben Hamed, Suliann; Boulinguez, Philippe

2011-08-01

Standard protocols testing the orientation of visuospatial attention usually present spatial cues before targets and compare valid-cue trials with invalid-cue trials. The valid/invalid contrast results in a relative behavioral or physiological difference that is generally interpreted as a benefit of attention orientation. However, growing evidence suggests that inhibitory control of response is closely involved in this kind of protocol that requires the subjects to withhold automatic responses to cues, probably biasing behavioral and physiological baselines. Here, we used two experiments to disentangle the inhibitory control of automatic responses from orienting of visuospatial attention in a saccadic reaction time task in humans, a variant of the classical cue-target detection task and a sustained visuospatial attentional task. Surprisingly, when referring to a simple target detection task in which there is no need to refrain from reacting to avoid inappropriate responses, we found no consistent evidence of facilitation of target detection at the attended location. Instead, we observed a cost at the unattended location. Departing from the classical view, our results suggest that reaction time measures of visuospatial attention probably relie on the attenuation of elementary processes involved in visual target detection and saccade initiation away from the attended location rather than on facilitation at the attended location. This highlights the need to use proper control conditions in experimental designs to disambiguate relative from absolute cueing benefits on target detection reaction times, both in psychophysical and neurophysiological studies.

Taking Care of Business.

ERIC Educational Resources Information Center

Stone, William E.

1989-01-01

Properly designed and properly evaluated, entrepreneurial activities can have many kinds of positive financial and non-financial results for an alumni program. A service or product line that alumni can not get from any other source can benefit the budget and both internal and external goodwill. (MSE)

FOOD RISK ANALYSIS

USDA-ARS?s Scientific Manuscript database

Food risk analysis is a holistic approach to food safety because it considers all aspects of the problem. Risk assessment modeling is the foundation of food risk analysis. Proper design and simulation of the risk assessment model is important to properly predict and control risk. Because of knowl...

Guidelines and Suggestions for Balloon Gondola Design

NASA Technical Reports Server (NTRS)

Franco, Hugo

2017-01-01

This paper discusses the current gondola design requirements for the Columbia Scientific Balloon Facility (CSBF). The CSBF is responsible for launching and supporting balloon borne scientific instruments and has some current updated guidelines that will be discussed in this presentation. As the sophistication of Payload systems have increased in size and complexity new guidelines have been implemented in order to make these instruments stay within the acceptable launch risks. Additionally, there is a requirement to submit a proper stress analysis report that states the flight design requirements have been met. Suggestions are discussed in this presentation that establish the proper guidelines to submit these.

Operation of inspection stations for child restraint use

DOT National Transportation Integrated Search

2003-01-01

Inspection stations are locations where parents and caregivers can go to receive one-on-one tutorial instruction on the proper use and installation of child restraints. The objective of this project was to identify and describe the characteristics of...

Primitive Saltmaking and Marine Science Education.

ERIC Educational Resources Information Center

Spence, Lundie; Copeland, B. J.

1985-01-01

Describes the procedures employed to make salt from seawater. Reviews the basic principles of seawater chemistry and discusses the techniques used to measure salinity. Identifies major saltworks locations and indicates the proper conditions needed for solar production of salt. (ML)

Earthquake Early Warning: User Education and Designing Effective Messages

NASA Astrophysics Data System (ADS)

Burkett, E. R.; Sellnow, D. D.; Jones, L.; Sellnow, T. L.

2014-12-01

The U.S. Geological Survey (USGS) and partners are transitioning from test-user trials of a demonstration earthquake early warning system (ShakeAlert) to deciding and preparing how to implement the release of earthquake early warning information, alert messages, and products to the public and other stakeholders. An earthquake early warning system uses seismic station networks to rapidly gather information about an occurring earthquake and send notifications to user devices ahead of the arrival of potentially damaging ground shaking at their locations. Earthquake early warning alerts can thereby allow time for actions to protect lives and property before arrival of damaging shaking, if users are properly educated on how to use and react to such notifications. A collaboration team of risk communications researchers and earth scientists is researching the effectiveness of a chosen subset of potential earthquake early warning interface designs and messages, which could be displayed on a device such as a smartphone. Preliminary results indicate, for instance, that users prefer alerts that include 1) a map to relate their location to the earthquake and 2) instructions for what to do in response to the expected level of shaking. A number of important factors must be considered to design a message that will promote appropriate self-protective behavior. While users prefer to see a map, how much information can be processed in limited time? Are graphical representations of wavefronts helpful or confusing? The most important factor to promote a helpful response is the predicted earthquake intensity, or how strong the expected shaking will be at the user's location. Unlike Japanese users of early warning, few Californians are familiar with the earthquake intensity scale, so we are exploring how differentiating instructions between intensity levels (e.g., "Be aware" for lower shaking levels and "Drop, cover, hold on" at high levels) can be paired with self-directed supplemental information to increase the public's understanding of earthquake shaking and protective behaviors.

LED light design method for high contrast and uniform illumination imaging in machine vision.

PubMed

Wu, Xiaojun; Gao, Guangming

2018-03-01

In machine vision, illumination is very critical to determine the complexity of the inspection algorithms. Proper lights can obtain clear and sharp images with the highest contrast and low noise between the interested object and the background, which is conducive to the target being located, measured, or inspected. Contrary to the empirically based trial-and-error convention to select the off-the-shelf LED light in machine vision, an optimization algorithm for LED light design is proposed in this paper. It is composed of the contrast optimization modeling and the uniform illumination technology for non-normal incidence (UINI). The contrast optimization model is built based on the surface reflection characteristics, e.g., the roughness, the reflective index, and light direction, etc., to maximize the contrast between the features of interest and the background. The UINI can keep the uniformity of the optimized lighting by the contrast optimization model. The simulation and experimental results demonstrate that the optimization algorithm is effective and suitable to produce images with the highest contrast and uniformity, which is very inspirational to the design of LED illumination systems in machine vision.

Intraparenchymal epidermoid cyst: proper surgical management may lead to satisfactory outcome.

PubMed

Zheng, Jian; Wang, Chun; Liu, Fengqiang

2018-03-12

Intraparenchymal epidermoid cysts (IECs) are rare lesions, thus the preoperative diagnosis and proper surgical management are still a challenge. We searched the database at our institution and performed a search of English literature in PubMed and Google Scholar. Keywords used were as follows: "intraparenchymal"; "intracerebral"; "intraaxial"; "epidermoid cyst"; "brainstem"; "cholesteatoma"; "pearly tumor". Only cases that were true intraparenchymally located and contained adequate clinical information were included. Six cases of IECs were recorded at our institution. Total removal was achieved in all the six patients with good outcomes. 29 cases meeting the above criteria were found in the literature. Including ours, a total of 35 patients were analyzed. Females were more frequently affected (F/M ratio, 1.9:1). Most of them were located in the brainstem (42.9%) and temporal lobe (22.9%). While in children, all were located in the brainstem. 45.2% showed subtle peripheral enhancement on Magnetic Resonance Imaging (MRI), and all appeared hyperintense on Diffusion Weighted Imaging (DWI). In the subgroup of cerebral lobes and cerebellums, total resection was achieved in 89.5%, and they all showed good outcomes. While in the subgroup of brainstem, 46.7% (seven cases) underwent total resection and 50% (three cases) of them died postoperatively. MRI with DWI is helpful in the preoperative diagnosis. Total resection should be achieved for the IECs located in cerebral lobes and cerebellums, while subtotal resection is a wise and safe strategy for the IECs located in the brainstem.

Location-based technologies for supporting elderly pedestrian in "getting lost" events.

PubMed

Pulido Herrera, Edith

2017-05-01

Localization-based technologies promise to keep older adults with dementia safe and support them and their caregivers during getting lost events. This paper summarizes mainly technological contributions to support the target group in these events. Moreover, important aspects of the getting lost phenomenon such as its concept and ethical issues are also briefly addressed. Papers were selected from scientific databases and gray literature. Since the topic is still in its infancy, other terms were used to find contributions associated with getting lost e.g. wandering. Trends of applying localization systems were identified as personal locators, perimeter systems and assistance systems. The first system barely considered the older adult's opinion, while assistance systems may involve context awareness to improve the support for both the elderly and the caregiver. Since few studies report multidisciplinary work with a special focus on getting lost, there is not a strong evidence of the real efficiency of localization systems or guidelines to design systems for the target group. Further research about getting lost is required to obtain insights for developing customizable systems. Moreover, considering conditions of the older adult might increase the impact of developments that combine localization technologies and artificial intelligence techniques. Implications for Rehabilitation Whilst there is no cure for dementia such as Alzheimer's, it is feasible to take advantage of technological developments to somewhat diminish its negative impact. For instance, location-based systems may provide information to early diagnose the Alzheimer's disease by assessing navigational impairments of older adults. Assessing the latest supportive technologies and methodologies may provide insights to adopt strategies to properly manage getting lost events. More user-centered designs will provide appropriate assistance to older adults. Namely, customizable systems could assist older adults in their daily walks with the aim to increase their self-confidence, independence and autonomy.

An Assessment of the International Space Station's Trace Contaminant Control Subassembly Process Economics

NASA Technical Reports Server (NTRS)

Perry J. L.; Cole, H. E.; El-Lessy, H. N.

2005-01-01

The International Space Station (ISS) Environmental Control and Life Support System includes equipment speci.cally designed to actively remove trace chemical contamination from the cabin atmosphere. In the U.S. on-orbit segment, this function is provided by the trace contaminant control subassembly (TCCS) located in the atmosphere revitalization subsystem rack housed in the laboratory module, Destiny. The TCCS employs expendable adsorbent beds to accomplish its function leading to a potentially signi.cant life cycle cost over the life of the ISS. Because maintaining the TCCSs proper can be logistically intensive, its performance in .ight has been studied in detail to determine where savings may be achieved. Details of these studies and recommendations for improving the TCCS s process economics without compromising its performance or crew health and safety are presented and discussed.

Adaptive elastic metasurfaces for wave front manipulation

NASA Astrophysics Data System (ADS)

Li, Shilong; Xu, Jiawen; Tang, Jiong

2018-04-01

In this research, by combining the concept of elastic metasurfaces with piezoelectric transducer with shunted circuitry, we investigate the designs of elastic metasurfaces, consisting of an array of piezoelectric transducers shunted with negative capacitance, which is capable of modulating wave fronts adaptively. In order to construct different adaptive elastic metasurfaces, different phase profiles along the interface can be framed through properly adjusting the negative capacitance values. Flat planar lenses for focusing transmitted A0 Lamb waves are achieved, and possess the flexibility of changing focal locations through electromechanical tunings. Additionally, nonparaxial self-bending beams with arbitrary trajectories and source illusion devices can also be accomplished owing to the free manipulation of phase shifts. With their versatility and tunability, the adaptive elastic metasurfaces could pave new avenues to a wide variety of potential applications, such as nondestructive testing, ultrasound imaging, and caustic engineering.

Mounting system for optical frequency reference cavities

NASA Technical Reports Server (NTRS)

Notcutt, Mark (Inventor); Hall, John L. (Inventor); Ma, Long-Sheng (Inventor)

2008-01-01

A technique for reducing the vibration sensitivity of laser-stabilizing optical reference cavities is based upon an improved design and mounting method for the cavity, wherein the cavity is mounted vertically. It is suspended at one plane, around the spacer cylinder, equidistant from the mirror ends of the cavity. The suspension element is a collar of an extremely low thermal expansion coefficient material, which surrounds the spacer cylinder and contacts it uniformly. Once the collar has been properly located, it is cemented in place so that the spacer cylinder is uniformly supported and does not have to be squeezed at all. The collar also includes a number of cavities partially bored into its lower flat surface, around the axial bore. These cavities are support points, into which mounting base pins will be inserted. Hence the collar is supported at a minimum of three points.

Improved upper winds models for several astronomical observatories.

PubMed

Roberts, Lewis C; Bradford, L William

2011-01-17

An understanding of wind speed and direction as a function of height are critical to the proper modeling of atmospheric turbulence. We have used radiosonde data from launch sites near significant astronomical observatories and created averaged profiles of wind speed and direction and have also computed Richardson number profiles. Using data from the last 30 years, we confirm a 1977 Greenwood wind profile, and extend it to include parameters that show seasonal variations and differences in location. The added information from our models is useful for the design of adaptive optics systems and other imaging systems. Our analysis of the Richardson number suggests that persistent turbulent layers may be inferred when low values are present in our long term averaged data. Knowledge of the presence of these layers may help with planning for adaptive optics and laser communications.

Analysis and design of trial well mooring in deepwater of the South China Sea

NASA Astrophysics Data System (ADS)

Guo, Yongfeng; Ji, Shaojun; Tang, Changquan; Li, Jiansong; Zhong, Huiquan; Ian, Ong Chin Yam

2012-06-01

Mooring systems play an important role for semi-submersible rigs that drill in deepwater. A detailed analysis was carried out on the mooring of a semi-submersible rig that conducted a trial well drilling at a deepwater location in the South China Sea in 2009. The rig was 30 years old and had a shallow platform with a designed maximum operating water depth of 457 m. Following the mooring analysis, a mooring design was given that requires upgrading of the rig's original mooring system. The upgrade included several innovations, such as installing eight larger anchors, i.e. replacing the original anchors and inserting an additional 600 m of steel wires with the existing chains. All this was done to enhance the mooring capability of the rig in order for the rig to be held in position to conduct drilling at a water depth of 476 m. The overall duration of the drilling was 50 days and the upgraded mooring system proved to be efficient in achieving the goal of keeping the rig stationary while it was drilling the trial well in the South China Sea. This successful campaign demonstrates that an older semi-submersible rig can take on drilling in deep water after careful design and proper upgrading and modification to the original mooring system.

Field scale manure born animal waste management : GIS application

USDA-ARS?s Scientific Manuscript database

Intensive beef backgrounding often accumulate manure born soil nutrients, microbes, and pharmaceuticals at different site locations. Unless properly managed, such waste materials can pollute surrounding soil and water sources. Soil sampling from these sites helps determining waste material levels bu...

49 CFR 393.70 - Coupling devices and towing methods, except for driveaway-towaway operations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... slack at that location; and (4) Be provided with a locking device that prevents accidental separation of... more slack than is necessary to permit the vehicles to be turned properly. (3) The safety device, and...

Design, parametrization, and pole placement of stabilizing output feedback compensators via injective cogenerator quotient signal modules.

PubMed

Blumthaler, Ingrid; Oberst, Ulrich

2012-03-01

Control design belongs to the most important and difficult tasks of control engineering and has therefore been treated by many prominent researchers and in many textbooks, the systems being generally described by their transfer matrices or by Rosenbrock equations and more recently also as behaviors. Our approach to controller design uses, in addition to the ideas of our predecessors on coprime factorizations of transfer matrices and on the parametrization of stabilizing compensators, a new mathematical technique which enables simpler design and also new theorems in spite of the many outstanding results of the literature: (1) We use an injective cogenerator signal module ℱ over the polynomial algebra [Formula: see text] (F an infinite field), a saturated multiplicatively closed set T of stable polynomials and its quotient ring [Formula: see text] of stable rational functions. This enables the simultaneous treatment of continuous and discrete systems and of all notions of stability, called T-stability. We investigate stabilizing control design by output feedback of input/output (IO) behaviors and study the full feedback IO behavior, especially its autonomous part and not only its transfer matrix. (2) The new technique is characterized by the permanent application of the injective cogenerator quotient signal module [Formula: see text] and of quotient behaviors [Formula: see text] of [Formula: see text]-behaviors B. (3) For the control tasks of tracking, disturbance rejection, model matching, and decoupling and not necessarily proper plants we derive necessary and sufficient conditions for the existence of proper stabilizing compensators with proper and stable closed loop behaviors, parametrize all such compensators as IO behaviors and not only their transfer matrices and give new algorithms for their construction. Moreover we solve the problem of pole placement or spectral assignability for the complete feedback behavior. The properness of the full feedback behavior ensures the absence of impulsive solutions in the continuous case, and that of the compensator enables its realization by Kalman state space equations or elementary building blocks. We note that every behavior admits an IO decomposition with proper transfer matrix, but that most of these decompositions do not have this property, and therefore we do not assume the properness of the plant. (4) The new technique can also be applied to more general control interconnections according to Willems, in particular to two-parameter feedback compensators and to the recent tracking framework of Fiaz/Takaba/Trentelman. In contrast to these authors, however, we pay special attention to the properness of all constructed transfer matrices which requires more subtle algorithms.

Method for locating metallic nitride inclusions in metallic alloy ingots

DOEpatents

White, Jack C.; Traut, Davis E.; Oden, Laurance L.; Schmitt, Roman A.

1992-01-01

A method of determining the location and history of metallic nitride and/or oxynitride inclusions in metallic melts. The method includes the steps of labeling metallic nitride and/or oxynitride inclusions by making a coreduced metallic-hafnium sponge from a mixture of hafnium chloride and the chloride of a metal, reducing the mixed chlorides with magnesium, nitriding the hafnium-labeled metallic-hafnium sponge, and seeding the sponge to be melted with hafnium-labeled nitride inclusions. The ingots are neutron activated and the hafnium is located by radiometric means. Hafnium possesses exactly the proper metallurgical and radiochemical properties for this use.

Selecting Proper Plant Species for Mine Reclamation Using Fuzzy AHP Approach (Case Study: Chadormaloo Iron Mine of Iran)

NASA Astrophysics Data System (ADS)

Ebrahimabadi, Arash

2016-12-01

This paper describes an effective approach to select suitable plant species for reclamation of mined lands in Chadormaloo iron mine which is located in central part of Iran, near the city of Bafgh in Yazd province. After mine's total reserves are excavated, the mine requires to be permanently closed and reclaimed. Mine reclamation and post-mining land-use are the main issues in the phase of mine closure. In general, among various scenarios for mine reclamation process, i.e. planting, agriculture, forestry, residency, tourist attraction, etc., planting is the oldest and commonly-used technology for the reclamation of lands damaged by mining activities. Planting and vegetation play a major role in restoring productivity, ecosystem stability and biological diversity to degraded areas, therefore the main goal of this research work is to choose proper and suitable plants compatible with the conditions of Chadormaloo mined area, providing consistent conditions for future use. To ensure the sustainability of the reclaimed landscape, the most suitable plant species adapted to the mine conditions are selected. Plant species selection is a Multi Criteria Decision Making (MCDM) problem. In this paper, a fuzzy MCDM technique, namely Fuzzy Analytic Hierarchy Process (FAHP) is developed to assist chadormaloo iron mine managers and designers in the process of plant type selection for reclamation of the mine under fuzzy environment where the vagueness and uncertainty are taken into account with linguistic variables parameterized by triangular fuzzy numbers. The results achieved from using FAHP approach demonstrate that the most proper plant species are ranked as Artemisia sieberi, Salsola yazdiana, Halophytes types, and Zygophyllum, respectively for reclamation of Chadormaloo iron mine.

Optimization of a Lunar Pallet Lander Reinforcement Structure Using a Genetic Algorithm

NASA Technical Reports Server (NTRS)

Burt, Adam

2014-01-01

In this paper, a unique system level spacecraft design optimization will be presented. A Genetic Algorithm is used to design the global pattern of the reinforcing structure, while a gradient routine is used to adequately stiffen the sub-structure. The system level structural design includes determining the optimal physical location (and number) of reinforcing beams of a lunar pallet lander deck structure. Design of the substructure includes determining placement of secondary stiffeners and the number of rivets required for assembly.. In this optimization, several considerations are taken into account. The primary objective was to raise the primary natural frequencies of the structure such that the Pallet Lander primary structure does not significantly couple with the launch vehicle. A secondary objective is to determine how to properly stiffen the reinforcing beams so that the beam web resists the shear buckling load imparted by the spacecraft components mounted to the pallet lander deck during launch and landing. A third objective is that the calculated stress does not exceed the allowable strength of the material. These design requirements must be met while, minimizing the overall mass of the spacecraft. The final paper will discuss how the optimization was implemented as well as the results. While driven by optimization algorithms, the primary purpose of this effort was to demonstrate the capability of genetic algorithms to enable design automation in the preliminary design cycle. By developing a routine that can automatically generate designs through the use of Finite Element Analysis, considerable design efficiencies, both in time and overall product, can be obtained over more traditional brute force design methods.

Safe Youth. Safe Schools.

MedlinePlus

... evidence. Research/Data Sources Crime Prevention Through Environmental Design (CPTED) School Project Research has shown that proper environmental design can reduce crime and fear associated with criminal ...

Human Location Detection System Using Micro-Electromechanical Sensor for Intelligent Fan

NASA Astrophysics Data System (ADS)

Parnin, S.; Rahman, M. M.

2017-03-01

This paper presented the development of sensory system for detection of both the presence and the location of human in a room spaces using MEMS Thermal sensor. The system is able to detect the surface temperature of occupants by a non-contact detection at the maximum of 6 meters far. It can be integrated to any swing type of electrical appliances such as standing fan or a similar devices. Differentiating human from other moving and or static object by heat variable is nearly impossible since human, animals and electrical appliances produce heat. The uncontrollable heat properties which can change and transfer will add to the detection issue. Integrating the low cost MEMS based thermal sensor can solve the first of human sensing problem by its ability to detect human in stationary. Further discrimination and analysis must therefore be made to the measured temperature data to distinguish human from other objects. In this project, the fan is properly designed and program in such a way that it can adapt to different events starting from the human sensing stage to its dynamic and mechanical moving parts. Up to this stage initial testing to the Omron D6T microelectromechanical thermal sensor is currently under several experimental stages. Experimental result of the sensor tested on stationary and motion state of human are behaviorally differentiable and successfully locate the human position by detecting the maximum temperature of each sensor reading.

Selection and Placement of Students in Cooperative Programs

ERIC Educational Resources Information Center

Pender, Albert R.

1970-01-01

Factors to consider in properly implementing the selection-placement process are: (1) age, (2) needs, (3) interests, (4) aptitudes and abilities, (5) personality traits, (6) scholastic average, (7) attendance record, (8) appearance, (9) interpersonal relationships, (10) location, (11) hours, and (12) rotation. (DM)

Variation in asparagine concentration in Nebraska wheat

USDA-ARS?s Scientific Manuscript database

The concentration of asparagine in wheat grain depends on both genetics and environmental factors, therefore study of different wheat cultivars, growing locations and crops years is needed for proper evaluation of potential risks of acrylamide formation in baked products made from Nebraska wheats. T...

Auto-Mechanics Course. Bilingual Vocational Instructional Materials.

ERIC Educational Resources Information Center

Lopez-Cox, Guadalupe

This auto-mechanics course, one of a series of bilingual English-Spanish vocational education courses, is designed to introduce the basic skills that an automotive mechanics student should know. It is geared to teach the student basic manipulative skills, safety judgments, proper work habits, desirable attitudes, and proper behavior for initial…

Minimum-Impact Camping in the Front Woods.

ERIC Educational Resources Information Center

Schatz, Curt

1994-01-01

Minimum-impact camping techniques that can be applied to resident camp programs include controlling group size and behavior, designing camp sites, moving groups frequently, proper use of fires, proper disposal of food and human wastes, use of biodegradable soaps, and encouraging staff and camper awareness of impacts on the environment. (LP)

High Power Microwave (HPM) and Ionizing Radiation Effects on CMOS Devices

DTIC Science & Technology

2010-03-01

24 xviii Symbol Page VIH minimum input voltage for proper high voltage output...38 VOH output voltage corresponding to VIH ...design. The high level at the input, VIH , along with VDD, define the maximum permitted “Logic 1” region, which allows for proper state change for a

Geoexchange: Getting it Right

ERIC Educational Resources Information Center

Johnson, William C.; Ormond, Paul

2013-01-01

If properly installed, optimized geoexchange systems can be one of the most cost effective, powerful options to accomplish the goal of improved energy efficiency and reduced carbon emissions. Accurately quantifying field performance is an important step in designing a system that is the proper size and capacity. The authors share the real life…

36 CFR 1234.10 - What are the facility requirements for all records storage facilities?

Code of Federal Regulations, 2014 CFR

2014-07-01

... the HVAC systems, fire alarm and fire protection systems. Manual switching between sources of service... elements are protected by a properly installed, properly maintained wet-pipe automatic sprinkler system, as... must provide documentation that the facility has a fire suppression system specifically designed to...

How can information systems provide support to nurses' hand hygiene performance? Using gamification and indoor location to improve hand hygiene awareness and reduce hospital infections.

PubMed

Marques, Rita; Gregório, João; Pinheiro, Fernando; Póvoa, Pedro; da Silva, Miguel Mira; Lapão, Luís Velez

2017-01-31

Hospital-acquired infections are still amongst the major problems health systems are facing. Their occurrence can lead to higher morbidity and mortality rates, increased length of hospital stay, and higher costs for both hospital and patients. Performing hand hygiene is a simple and inexpensive prevention measure, but healthcare workers' compliance with it is often far from ideal. To raise awareness regarding hand hygiene compliance, individual behaviour change and performance optimization, we aimed to develop a gamification solution that collects data and provides real-time feedback accurately in a fun and engaging way. A Design Science Research Methodology (DSRM) was used to conduct this work. DSRM is useful to study the link between research and professional practices by designing, implementing and evaluating artifacts that address a specific need. It follows a development cycle (or iteration) composed by six activities. Two work iterations were performed applying gamification components, each using a different indoor location technology. Preliminary experiments, simulations and field studies were performed in an Intensive Care Unit (ICU) of a Portuguese tertiary hospital. Nurses working on this ICU were in a focus group during the research, participating in several sessions across the implementation process. Nurses enjoyed the concept and considered that it allows for a unique opportunity to receive feedback regarding their performance. Tests performed on the indoor location technology applied in the first iteration regarding distances estimation presented an unacceptable lack of accuracy. Using a proximity-based technique, it was possible to identify the sequence of positions, but beacons presented an unstable behaviour. In the second work iteration, a different indoor location technology was explored but it did not work properly, so there was no chance of testing the solution as a whole (gamification application included). Combining automated monitoring systems with gamification seems to be an innovative and promising approach, based on the already achieved results. Involving nurses in the project since the beginning allowed to align the solution with their needs. Despite strong evolution through recent years, indoor location technologies are still not ready to be applied in the healthcare field with nursing wards.

The Revised Neurobehavioral Severity Scale (NSS-R) for Rodents.

PubMed

Yarnell, Angela M; Barry, Erin S; Mountney, Andrea; Shear, Deborah; Tortella, Frank; Grunberg, Neil E

2016-04-08

Motor and sensory deficits are common following traumatic brain injury (TBI). Although rodent models provide valuable insight into the biological and functional outcomes of TBI, the success of translational research is critically dependent upon proper selection of sensitive, reliable, and reproducible assessments. Published literature includes various observational scales designed to evaluate post-injury functionality; however, the heterogeneity in TBI location, severity, and symptomology can complicate behavioral assessments. The importance of choosing behavioral outcomes that can be reliably and objectively quantified in an efficient manner is becoming increasingly important. The Revised Neurobehavioral Severity Scale (NSS-R) is a continuous series of specific, sensitive, and standardized observational tests that evaluate balance, motor coordination, and sensorimotor reflexes in rodents. The tasks follow a specific order designed to minimize interference: balance, landing, tail raise, dragging, righting reflex, ear reflex, eye reflex, sound reflex, tail pinch, and hindpaw pinch. The NSS-R has proven to be a reliable method differentiating brain-injured rodents from non-brain-injured rodents across many brain injury models. Copyright © 2016 John Wiley & Sons, Inc.

Benefits of production extension and shifting with thermal storage for a 1MW CSP-ORC plant in Morocco

NASA Astrophysics Data System (ADS)

Bennouna, El Ghali; Mimet, Abdelaziz; Frej, Hicham

2016-05-01

The importance of thermal storage for commercial CSP (concentrated Solar Power) plants has now become obvious, this regardless of the solar technology used and the power cycle. The availability of a storage system to a plant operator brings a lot of possibilities for production management, cash flow optimization and grid stabilizing. In particular, and depending on plant location and local grid strategy, thermal storage can contribute, when wisely used, to control production and adapt it to the demand and / or power unbalances and varying prices. Storage systems design, sizing and configuration are proper to each power plant, hence systems that are now widely installed within large commercial solar plants are not necessarily suited for small scale decentralized production, and will not have the same effects. In this paper the benefits of thermal storage are studied for a 1MWe CSP plant with an ORC (Organic Rankine Cycle), this plant has many specific features which call for a detail analysis about the appropriate storage design and optimum operating strategies for decentralized solutions.

Design of Fishing Boat for Pelabuhanratu Fishermen as One of Effort to Increase Production of Capture Fisheries

NASA Astrophysics Data System (ADS)

Nur, Iswadi; Joko Suranto, Purwo

2018-02-01

Design of fishing boat for Pelabuhanratu fisherman as one of effort to increase production of capture fisheries. The fishing boat should be proper for the characteristic of its service area, as; capacity of fishing boat up to 60 GT, the fishing boat has minimum 6 fish holds and location of fish hold in the middle body, the fishing boat hull has the bilge keel plate, and the material of hull fishing boat to be made of wooden, steel, aluminium, or fiberglass. Main dimesion of fishing boat is Length Over All = 25.436 m, Breadth = 4.55 m, Draft = 1.6 m, Speed = 12.5 knots. The research had been known every thing that will be supporting the production of capture fisheries like ; amount of fish production = 25.030 ton per day, the fishing port capacity approximately 268.957GT per day, the area of fishing port < 30 hectares, the zone of fish processing industry had not completed, therefore all data research result less than standard of Oceanic Fising Port. So Pelabuhanratu National Fishing Port can not be changed to Oceanic Fishing Port.

The Gould’s Belt Distances Survey (GOBELINS). I. Trigonometric Parallax Distances and Depth of the Ophiuchus Complex

NASA Astrophysics Data System (ADS)

Ortiz-León, Gisela N.; Loinard, Laurent; Kounkel, Marina A.; Dzib, Sergio A.; Mioduszewski, Amy J.; Rodríguez, Luis F.; Torres, Rosa M.; González-Lópezlira, Rosa A.; Pech, Gerardo; Rivera, Juana L.; Hartmann, Lee; Boden, Andrew F.; Evans, Neal J., II; Briceño, Cesar; Tobin, John J.; Galli, Phillip A. B.; Gudehus, Donald

2017-01-01

We present the first results of the Gould’s Belt Distances Survey (GOBELINS), a project aimed at measuring the proper motion and trigonometric parallax of a large sample of young stars in nearby regions using multi-epoch Very Long Baseline Array (VLBA) radio observations. Enough VLBA detections have now been obtained for 16 stellar systems in Ophiuchus to derive their parallax and proper motion. This leads to distance determinations for individual stars with an accuracy of 0.3 to a few percent. In addition, the orbits of six multiple systems were modelled by combining absolute positions with VLBA (and, in some cases, near-infrared) angular separations. Twelve stellar systems are located in the dark cloud Lynds 1688 the individual distances for this sample are highly consistent with one another and yield a mean parallax for Lynds 1688 of \\varpi =7.28+/- 0.06 mas, corresponding to a distance d=137.3+/- 1.2 pc. This represents an accuracy greater than 1%. Three systems for which astrometric elements could be measured are located in the eastern streamer (Lynds 1689) and yield an estimate of \\varpi =6.79+/- 0.16 mas, corresponding to a distance d=147.3+/- 3.4 pc. This suggests that the eastern streamer is located about 10 pc farther than the core, but this conclusion needs to be confirmed by observations of additional sources in the eastern streamer (currently being collected). From the measured proper motions, we estimate the one-dimensional velocity dispersion in Lynds 1688 to be 2.8 ± 1.8 and 3.0 ± 2.0 km s-1, in R.A. and decl., respectively; these are larger than, but still consistent within 1σ of, those found in other studies.

Soil erosion assessment and its correlation with landslide events using remote sensing data and GIS: a case study at Penang Island, Malaysia.

PubMed

Pradhan, Biswajeet; Chaudhari, Amruta; Adinarayana, J; Buchroithner, Manfred F

2012-01-01

In this paper, an attempt has been made to assess, prognosis and observe dynamism of soil erosion by universal soil loss equation (USLE) method at Penang Island, Malaysia. Multi-source (map-, space- and ground-based) datasets were used to obtain both static and dynamic factors of USLE, and an integrated analysis was carried out in raster format of GIS. A landslide location map was generated on the basis of image elements interpretation from aerial photos, satellite data and field observations and was used to validate soil erosion intensity in the study area. Further, a statistical-based frequency ratio analysis was carried out in the study area for correlation purposes. The results of the statistical correlation showed a satisfactory agreement between the prepared USLE-based soil erosion map and landslide events/locations, and are directly proportional to each other. Prognosis analysis on soil erosion helps the user agencies/decision makers to design proper conservation planning program to reduce soil erosion. Temporal statistics on soil erosion in these dynamic and rapid developments in Penang Island indicate the co-existence and balance of ecosystem.

Evaluation of Effective Factors on Travel Time in Optimization of Bus Stops Placement Using Genetic Algorithm

NASA Astrophysics Data System (ADS)

Bargegol, Iraj; Ghorbanzadeh, Mahyar; Ghasedi, Meisam; Rastbod, Mohammad

2017-10-01

In congested cities, locating and proper designing of bus stops according to the unequal distribution of passengers is crucial issue economically and functionally, since this subject plays an important role in the use of bus system by passengers. Location of bus stops is a complicated subject; by reducing distances between stops, walking time decreases, but the total travel time may increase. In this paper, a specified corridor in the city of Rasht in north of Iran is studied. Firstly, a new formula is presented to calculate the travel time, by which the number of stops and consequently, the travel time can be optimized. An intended corridor with specified number of stops and distances between them is addressed, the related formulas to travel time are created, and its travel time is calculated. Then the corridor is modelled using a meta-heuristic method in order that the placement and the optimal distances of bus stops for that are determined. It was found that alighting and boarding time along with bus capacity are the most effective factors affecting travel time. Consequently, it is better to have more concentration on indicated factors for improving the efficiency of bus system.

Nodal Diffusion Burnable Poison Treatment for Prismatic Reactor Cores

DOE Office of Scientific and Technical Information (OSTI.GOV)

A. M. Ougouag; R. M. Ferrer

2010-10-01

The prismatic block version of the High Temperature Reactor (HTR) considered as a candidate Very High Temperature Reactor (VHTR)design may use burnable poison pins in locations at some corners of the fuel blocks (i.e., assembly equivalent structures). The presence of any highly absorbing materials, such as these burnable poisons, within fuel blocks for hexagonal geometry, graphite-moderated High Temperature Reactors (HTRs) causes a local inter-block flux depression that most nodal diffusion-based method have failed to properly model or otherwise represent. The location of these burnable poisons near vertices results in an asymmetry in the morphology of the assemblies (or blocks). Hencemore » the resulting inadequacy of traditional homogenization methods, as these “spread” the actually local effect of the burnable poisons throughout the assembly. Furthermore, the actual effect of the burnable poison is primarily local with influence in its immediate vicinity, which happens to include a small region within the same assembly as well as similar regions in the adjacent assemblies. Traditional homogenization methods miss this artifact entirely. This paper presents a novel method for treating the local effect of the burnable poison explicitly in the context of a modern nodal method.« less

Digital image comparison by subtracting contextual transformations—percentile rank order differentiation

USGS Publications Warehouse

Wehde, M. E.

1995-01-01

The common method of digital image comparison by subtraction imposes various constraints on the image contents. Precise registration of images is required to assure proper evaluation of surface locations. The attribute being measured and the calibration and scaling of the sensor are also important to the validity and interpretability of the subtraction result. Influences of sensor gains and offsets complicate the subtraction process. The presence of any uniform systematic transformation component in one of two images to be compared distorts the subtraction results and requires analyst intervention to interpret or remove it. A new technique has been developed to overcome these constraints. Images to be compared are first transformed using the cumulative relative frequency as a transfer function. The transformed images represent the contextual relationship of each surface location with respect to all others within the image. The process of differentiating between the transformed images results in a percentile rank ordered difference. This process produces consistent terrain-change information even when the above requirements necessary for subtraction are relaxed. This technique may be valuable to an appropriately designed hierarchical terrain-monitoring methodology because it does not require human participation in the process.

Location estimation in a smart home: system implementation and evaluation using experimental data.

PubMed

Rahal, Youcef; Pigot, Hélène; Mabilleau, Philippe

2008-01-01

In the context of a constantly increasing aging population with cognitive deficiencies, insuring the autonomy of the elders at home becomes a priority. The DOMUS laboratory is addressing this issue by conceiving a smart home which can both assist people and preserve their quality of life. Obviously, the ability to monitor properly the occupant's activities and thus provide the pertinent assistance depends highly on location information inside the smart home. This paper proposes a solution to localize the occupant thanks to Bayesian filtering and a set of anonymous sensors disseminated throughout the house. The localization system is designed for a single person inside the house. It could however be used in conjunction with other localization systems in case more people are present. Our solution is functional in real conditions. We conceived an experiment to estimate precisely its accuracy and evaluate its robustness. The experiment consists of a scenario of daily routine meant to maximize the occupant's motion in meaningful activities. It was performed by 14 subjects, one subject at a time. The results are satisfactory: the system's accuracy exceeds 85% and is independent of the occupant's profile. The system works in real time and behaves well in presence of noise.

All-Direction Random Routing for Source-Location Privacy Protecting against Parasitic Sensor Networks

PubMed Central

Wang, Na; Zeng, Jiwen

2017-01-01

Wireless sensor networks are deployed to monitor the surrounding physical environments and they also act as the physical environments of parasitic sensor networks, whose purpose is analyzing the contextual privacy and obtaining valuable information from the original wireless sensor networks. Recently, contextual privacy issues associated with wireless communication in open spaces have not been thoroughly addressed and one of the most important challenges is protecting the source locations of the valuable packages. In this paper, we design an all-direction random routing algorithm (ARR) for source-location protecting against parasitic sensor networks. For each package, the routing process of ARR is divided into three stages, i.e., selecting a proper agent node, delivering the package to the agent node from the source node, and sending it to the final destination from the agent node. In ARR, the agent nodes are randomly chosen in all directions by the source nodes using only local decisions, rather than knowing the whole topology of the networks. ARR can control the distributions of the routing paths in a very flexible way and it can guarantee that the routing paths with the same source and destination are totally different from each other. Therefore, it is extremely difficult for the parasitic sensor nodes to trace the packages back to the source nodes. Simulation results illustrate that ARR perfectly confuses the parasitic nodes and obviously outperforms traditional routing-based schemes in protecting source-location privacy, with a marginal increase in the communication overhead and energy consumption. In addition, ARR also requires much less energy than the cloud-based source-location privacy protection schemes. PMID:28304367

Occupancy Modeling Species-Environment Relationships with Non-ignorable Survey Designs.

PubMed

Irvine, Kathryn M; Rodhouse, Thomas J; Wright, Wilson J; Olsen, Anthony R

2018-05-26

Statistical models supporting inferences about species occurrence patterns in relation to environmental gradients are fundamental to ecology and conservation biology. A common implicit assumption is that the sampling design is ignorable and does not need to be formally accounted for in analyses. The analyst assumes data are representative of the desired population and statistical modeling proceeds. However, if datasets from probability and non-probability surveys are combined or unequal selection probabilities are used, the design may be non ignorable. We outline the use of pseudo-maximum likelihood estimation for site-occupancy models to account for such non-ignorable survey designs. This estimation method accounts for the survey design by properly weighting the pseudo-likelihood equation. In our empirical example, legacy and newer randomly selected locations were surveyed for bats to bridge a historic statewide effort with an ongoing nationwide program. We provide a worked example using bat acoustic detection/non-detection data and show how analysts can diagnose whether their design is ignorable. Using simulations we assessed whether our approach is viable for modeling datasets composed of sites contributed outside of a probability design Pseudo-maximum likelihood estimates differed from the usual maximum likelihood occu31 pancy estimates for some bat species. Using simulations we show the maximum likelihood estimator of species-environment relationships with non-ignorable sampling designs was biased, whereas the pseudo-likelihood estimator was design-unbiased. However, in our simulation study the designs composed of a large proportion of legacy or non-probability sites resulted in estimation issues for standard errors. These issues were likely a result of highly variable weights confounded by small sample sizes (5% or 10% sampling intensity and 4 revisits). Aggregating datasets from multiple sources logically supports larger sample sizes and potentially increases spatial extents for statistical inferences. Our results suggest that ignoring the mechanism for how locations were selected for data collection (e.g., the sampling design) could result in erroneous model-based conclusions. Therefore, in order to ensure robust and defensible recommendations for evidence-based conservation decision-making, the survey design information in addition to the data themselves must be available for analysts. Details for constructing the weights used in estimation and code for implementation are provided. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Moon Illusion: An Observation.

PubMed

Goldstein, G

1962-12-21

Size comparisons of the moon are made from different locations by direct viewing (as opposed to comparisons by instrumental techniques). Under the proper conditions, the illusion is seen while the moon's position remains essentially unaltered. By this means, evidence is adduced in favor of Ptolemy's apparent-distance hypothesis.

QUANTIFYING SUBGRID POLLUTANT VARIABILITY IN EULERIAN AIR QUALITY MODELS

EPA Science Inventory

In order to properly assess human risk due to exposure to hazardous air pollutants or air toxics, detailed information is needed on the location and magnitude of ambient air toxic concentrations. Regional scale Eulerian air quality models are typically limited to relatively coar...

INTEGRATION OF STATISTICS, REMOTE SENSING AND EXISTING DATA TO LOCATE CHANGES IN LAND RESOURCES

EPA Science Inventory

Stability of a nation is dependent on the availability of natural resources. When land is degraded and natural resources become limited, socioeconomic status declines and emigration increases in developing countries. Natural resource utilization without proper management may re...

Environmentally safe areas and routes in the Baltic proper using Eulerian tracers.

PubMed

Höglund, A; Meier, H E M

2012-07-01

In recent years, the shipping of environmentally hazardous cargo has increased considerably in the Baltic proper. In this study, a large number of hypothetical oil spills with an idealized, passive tracer are simulated. From the tracer distributions, statistical measures are calculated to optimize the quantity of tracer from a spill that would stay at sea as long as possible. Increased time may permit action to be taken against the spill before the oil reaches environmentally vulnerable coastal zones. The statistical measures are used to calculate maritime routes with maximum probability that an oil spill will stay at sea as long as possible. Under these assumptions, ships should follow routes that are located south of Bornholm instead of the northern routes in use currently. Our results suggest that the location of the optimal maritime routes depends on the season, although interannual variability is too large to identify statistically significant changes. Copyright © 2012. Published by Elsevier Ltd.

Instabilities of geared couplings: Theory and practice

NASA Technical Reports Server (NTRS)

Kirk, R. G.; Mondy, R. E.; Murphy, R. C.

1982-01-01

The use of couplings for high speed turbocompressors or pumps is essential to transmit power from the driver. Typical couplings are either of the lubricated gear or dry diaphragm type design. Gear couplings have been the standard design for many years and recent advances in power and speed requirements have pushed the standard design criteria to the limit. Recent test stand and field data on continuous lube gear type couplings have forced a closer examination of design tolerances and concepts to avoid operational instabilities. Two types of mechanical instabilities are reviewed in this paper: (1) entrapped fluid, and (2) gear mesh instability resulting in spacer throw-out onset. Test stand results of these types of instabilities and other directly related problems are presented together with criteria for proper coupling design to avoid these conditions. An additional test case discussed shows the importance of proper material selection and processing and what can happen to an otherwise good design.

The Mission Assessment Post Processor (MAPP): A New Tool for Performance Evaluation of Human Lunar Missions

NASA Technical Reports Server (NTRS)

Williams, Jacob; Stewart, Shaun M.; Lee, David E.; Davis, Elizabeth C.; Condon, Gerald L.; Senent, Juan

2010-01-01

The National Aeronautics and Space Administration s (NASA) Constellation Program paves the way for a series of lunar missions leading to a sustained human presence on the Moon. The proposed mission design includes an Earth Departure Stage (EDS), a Crew Exploration Vehicle (Orion) and a lunar lander (Altair) which support the transfer to and from the lunar surface. This report addresses the design, development and implementation of a new mission scan tool called the Mission Assessment Post Processor (MAPP) and its use to provide insight into the integrated (i.e., EDS, Orion, and Altair based) mission cost as a function of various mission parameters and constraints. The Constellation architecture calls for semiannual launches to the Moon and will support a number of missions, beginning with 7-day sortie missions, culminating in a lunar outpost at a specified location. The operational lifetime of the Constellation Program can cover a period of decades over which the Earth-Moon geometry (particularly, the lunar inclination) will go through a complete cycle (i.e., the lunar nodal cycle lasting 18.6 years). This geometry variation, along with other parameters such as flight time, landing site location, and mission related constraints, affect the outbound (Earth to Moon) and inbound (Moon to Earth) translational performance cost. The mission designer must determine the ability of the vehicles to perform lunar missions as a function of this complex set of interdependent parameters. Trade-offs among these parameters provide essential insights for properly assessing the ability of a mission architecture to meet desired goals and objectives. These trades also aid in determining the overall usable propellant required for supporting nominal and off-nominal missions over the entire operational lifetime of the program, thus they support vehicle sizing.

Use of fully biodegradable panels to reduce derelict pot threats to marine fauna.

PubMed

Bilkovic, D M; Havens, K J; Stanhope, D M; Angstadt, K T

2012-12-01

Fishing pots (i.e., traps) are designed to catch fish or crustaceans and are used globally. Lost pots are a concern for a variety of fisheries, and there are reports that 10-70% of deployed pots are lost annually. Derelict fishing pots can be a source of mortality for target and bycatch species for several years. Because continual removal of derelict gear can be impractical over large spatial extents, modifications are needed to disarm gear once it is lost. We tested a fully biodegradable panel with a cull or escape ring designed for placement on the sides of a crab pot that completely degrades into environmentally neutral constituents after approximately 1 year. This panel is relatively inexpensive, easy to install, and can be used in multiple fisheries. We used the blue crab (Callinectes sapidus) fishery as a test case because it is a large pot fishery and blue crab pots are similar to traps used in other pot fisheries. We had commercial fishers deploy pots with panels alongside standard pots in Chesapeake Bay (U.S.A.) to assess potential effects of our experimental pots on blue crab catch. We compared the number, biomass, and size of crabs captured between standard and experimental pots and evaluated differences in catch over a crabbing season (March-November) at five locations. There was no evidence that biodegradable panels adversely affected catch. In all locations and time periods, legal catches were comparable in abundance, biomass, and size between experimental and standard pots. Properly designed biodegradable panels appear to be a viable solution to mitigate adverse effects of derelict pots. ©2012 Society for Conservation Biology.

Observation of valley-selective microwave transport in photonic crystals

NASA Astrophysics Data System (ADS)

Ye, Liping; Yang, Yuting; Hong Hang, Zhi; Qiu, Chunyin; Liu, Zhengyou

2017-12-01

Recently, the discrete valley degree of freedom has attracted extensive attention in condensed matter physics. Here, we present an experimental observation of the intriguing valley transport for microwaves in photonic crystals, including the bulk valley transport and the valley-projected edge modes along the interface separating different photonic insulating phases. For both cases, valley-selective excitations are realized by a point-like chiral source located at proper locations inside the samples. Our results are promising for exploring unprecedented routes to manipulate microwaves.

Developing a control system for ARES 2

NASA Technical Reports Server (NTRS)

Fitzsimons, Philip M.

1992-01-01

A great deal of analysis and testing is conducted at the NASA Langley Research Center to support the development of safe and reliable helicopter rotor systems. This work is performed by the Rotorcraft Aeroelasticity Group located in the Transonic Dynamics Tunnel (TDT) facility. Over the past two decades a wide variety of tests have been successfully conducted in the TDT and their results have contributed significantly to the understanding of aeromechanical phenomena in rotor systems. This has led to improved tools for analysis and design, and ultimately to the development, of improved rotor systems. The TDT facility is ideally suited for these tests due to its unique ability to use a heavy gas as a working medium. This allows the model to be scaled such that the results obtained may be readily extrapolated to full scale. Until recently, the rotor system to be tested has been mounted on a fixed balance which is attached to the longeron which is attached to the stand through a single pitching degree of freedom. The testbed used is known as the Aeroelastic Rotor Experimental System (ARES 1). In order to extend the experimental capabilities to investigate the full rotor/body dynamic coupling present in a rotorcraft, a very ambitious project has been undertaken to design and construct a six degree of freedom system that can be controlled so as to emulate the inertial characteristics of a prescribed model fuselage. The electronic and mechanical hardware for this system has already been designed and constructed. This system is known ar ARES II. The rotor and its drive system are mounted on the balance which is attached to the longeron via six hydraulic actuators. This six degree of freedom parallel linkage is referred to in the literature as a Stuart Platform. By properly adjusting the length of the hydraulic actuators it is possible to position and orient the balance relative to the longeron. The longeron is attached to the stand via a pitch degree of freedom to allow testing over various forward flight regimes. One major task remaining to complete this testbed is the design and synthesis of a control system. To do this properly requires an understanding of the kinematics and dynamics of the system and robust control design. A brief description of the development of a control design is given.

Hybrid PV/Wind Power Systems Incorporating Battery Storage and Considering the Stochastic Nature of Renewable Resources

NASA Astrophysics Data System (ADS)

Barnawi, Abdulwasa Bakr

Hybrid power generation system and distributed generation technology are attracting more investments due to the growing demand for energy nowadays and the increasing awareness regarding emissions and their environmental impacts such as global warming and pollution. The price fluctuation of crude oil is an additional reason for the leading oil producing countries to consider renewable resources as an alternative. Saudi Arabia as the top oil exporter country in the word announced the "Saudi Arabia Vision 2030" which is targeting to generate 9.5 GW of electricity from renewable resources. Two of the most promising renewable technologies are wind turbines (WT) and photovoltaic cells (PV). The integration or hybridization of photovoltaics and wind turbines with battery storage leads to higher adequacy and redundancy for both autonomous and grid connected systems. This study presents a method for optimal generation unit planning by installing a proper number of solar cells, wind turbines, and batteries in such a way that the net present value (NPV) is minimized while the overall system redundancy and adequacy is maximized. A new renewable fraction technique (RFT) is used to perform the generation unit planning. RFT was tested and validated with particle swarm optimization and HOMER Pro under the same conditions and environment. Renewable resources and load randomness and uncertainties are considered. Both autonomous and grid-connected system designs were adopted in the optimal generation units planning process. An uncertainty factor was designed and incorporated in both autonomous and grid connected system designs. In the autonomous hybrid system design model, the strategy including an additional amount of operation reserve as a percent of the hourly load was considered to deal with resource uncertainty since the battery storage system is the only backup. While in the grid-connected hybrid system design model, demand response was incorporated to overcome the impact of uncertainty and perform energy trading between the hybrid grid utility and main grid utility in addition to the designed uncertainty factor. After the generation unit planning was carried out and component sizing was determined, adequacy evaluation was conducted by calculating the loss of load expectation adequacy index for different contingency criteria considering probability of equipment failure. Finally, a microgrid planning was conducted by finding the proper size and location to install distributed generation units in a radial distribution network.

The effect of heterogeneity identifying the leakage of carbon dioxide in a shallow aquifer: an experimental study

NASA Astrophysics Data System (ADS)

Ha, S. W.; Lee, S. H.; Jeon, W. T.; Joo, Y. J.; Lee, K. K.

2014-12-01

Carbon dioxide (CO2) leakage into the shallow aquifer is one of the main concerns at a CO2 sequestration site. Various hydrogeochemical parameters have been suggested to determine the leakage (i.e., pH, EC, Alkalinity, Ca and δ13C). For the practical point of view, direct and continuous measurement of the dissolved CO2 concentration at the proper location can be the most useful strategy for the CO2 leakage detection in a shallow aquifer. In order to enhance possibility of identifying leaked CO2, monitoring location should be determined with regard to the shallow aquifer heterogeneity. In this study, a series of experiments were conducted to investigate the effects of heterogeneity on the dissolved CO2 concentrations. A 2-D sand tank of homogeneous medium sands including a single heterogeneity layer was designed. Two NDIR CO2 sensors, modified for continuous measuring in aquatic system, were installed above and below the single heterogeneous layer (clay, fine and medium sand lenses). Also, temperature and water contents were measured continuously at a same position. Bromocresol purple which is one of the acid-base indicator was used to visualize CO2 migration. During the gas phase CO2 injection at the bottom of the sand tank, dissolved CO2 in the water is continuously measured. In the results, significant differences of concentrations were observed due to the presence of heterogeneity layer, even the locations were close. These results suggested that monitoring location should be determined considering vertical heterogeneity of shallow aquifer at a CO2 leakage site.

30 CFR 90.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 90.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

14 CFR 27.733 - Tires.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Tires. 27.733 Section 27.733 Aeronautics... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction Landing Gear § 27.733 Tires. (a) Each landing gear wheel must have a tire— (1) That is a proper fit on the rim of the wheel; and (2) Of the proper...

Causes of Indoor Air Quality Problems in Schools: Summary of Scientific Research. Revised Edition.

ERIC Educational Resources Information Center

Bayer, Charlene W.; Crow, Sidney A.; Fischer, John

Understanding the primary causes of indoor air quality (IAQ) problems and how controllable factors--proper heating, ventilation and air-conditioning (HVAC) system design, allocation of adequate outdoor air, proper filtration, effective humidity control, and routine maintenance--can avert problems may help all building owners, operators, and…

Construction Trade Course. Bilingual Vocational Instructional Materials.

ERIC Educational Resources Information Center

Lopez-Cox, Guadalupe

This building trades course, one of a series of bilingual English-Spanish vocational education courses, is designed to introduce the basic skills that a student must know in the construction field. It is geared to teach the student basic manipulative skills, safety judgments, proper work habits, desirable attitudes, and proper behavior for initial…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brusati, M.; Camplani, A.; Cannon, M.

SRAM-ba8ed Field Programmable Gate Array (FPGA) logic devices arc very attractive in applications where high data throughput is needed, such as the latest generation of High Energy Physics (HEP) experiments. FPGAs have been rarely used in such experiments because of their sensitivity to radiation. The present paper proposes a mitigation approach applied to commercial FPGA devices to meet the reliability requirements for the front-end electronics of the Liquid Argon (LAr) electromagnetic calorimeter of the ATLAS experiment, located at CERN. Particular attention will be devoted to define a proper mitigation scheme of the multi-gigabit transceivers embedded in the FPGA, which ismore » a critical part of the LAr data acquisition chain. A demonstrator board is being developed to validate the proposed methodology. :!\\litigation techniques such as Triple Modular Redundancy (T:t\\IR) and scrubbing will be used to increase the robustness of the design and to maximize the fault tolerance from Single-Event Upsets (SEUs).« less

Degradation and Reinforcement of Industrial Gas Tank Support Structures. Thirty-Year Long Monitoring

NASA Astrophysics Data System (ADS)

Krentowski, Janusz R.; Knyziak, Piotr

2017-10-01

An analysis of reinforced concrete supporting structures of more than a dozen liquid gas tanks mounted on tower support structures located at different sites on Poland’s territory is presented. Stability testing of the degraded structures was carried out over a period of 30 years and pointed out significant defects that prevented safe operation of the tanks containing hazardous medium. Analysing complex stress states, as well as displacements of shell structure components, the authors developed a concept of strengthening the structures. Initial repair works, which had been carried out without proper supervision, failed to meet the mandatory requirements and were not compatible with the original design solutions. After several years of operation of the reinforced structures, their degradation states were assessed again. The next stage of repair works was carried out under the supervision of the authors together with authorized representatives of the investors.

Considerations for acoustic emission monitoring of spherical Kevlar/epoxy composite pressure vessels

NASA Technical Reports Server (NTRS)

Hamstad, M. A.; Patterson, R. G.

1977-01-01

We are continuing to research the applications of acoustic emission testing for predicting burst pressure of filament-wound Kevlar 49/epoxy pressure vessels. This study has focused on three specific areas. The first area involves development of an experimental technique and the proper instrumentation to measure the energy given off by the acoustic emission transducer per acoustic emission burst. The second area concerns the design of a test fixture in which to mount the composite vessel so that the acoustic emission transducers are held against the outer surface of the composite. Included in this study area is the calibration of the entire test setup including couplant, transducer, electronics, and the instrument measuring the energy per burst. In the third and final area of this study, we consider the number, location, and sensitivity of the acoustic emission transducers used for proof testing composite pressure vessels.

Microwave Nondestructive Evaluation of Dielectric Materials with a Metamaterial Lens

NASA Technical Reports Server (NTRS)

Shreiber, Daniel; Gupta, Mool; Cravey, Robin L.

2008-01-01

A novel microwave Nondestructive Evaluation (NDE) sensor was developed in an attempt to increase the sensitivity of the microwave NDE method for detection of defects small relative to a wavelength. The sensor was designed on the basis of a negative index material (NIM) lens. Characterization of the lens was performed to determine its resonant frequency, index of refraction, focus spot size, and optimal focusing length (for proper sample location). A sub-wavelength spot size (3 dB) of 0.48 lambda was obtained. The proof of concept for the sensor was achieved when a fiberglass sample with a 3 mm diameter through hole (perpendicular to the propagation direction of the wave) was tested. The hole was successfully detected with an 8.2 cm wavelength electromagnetic wave. This method is able to detect a defect that is 0.037 lambda. This method has certain advantages over other far field and near field microwave NDE methods currently in use.

Solar energy facility at North Hampton Recreation Center, Dallas, Texas

NASA Technical Reports Server (NTRS)

1980-01-01

The solar energy facility located at the North Hampton Park Recreation and Health Center, Dallas, Texas is presented. The solar energy system is installed in a single story (two heights), 16,000 sq ft building enclosing a gymnasium, locker area, and health care clinic surrounded by a recreational area and athletic field. The solar energy system is designed to provide 80 percent of the annual space heating, 48 percent of the annual space cooling, and 90 percent of the domestic hot water requirements. The system's operation modes and performance data acquisition system are described. The system's performance during the months of June, July, August, September, and October of 1979 are presented and show a negative savings of energy. Experience to date indicates however that the system concept has promise of acceptable performance. It is concluded that if proper control and sequencing components was maintained, then the system performance would improve to an acceptable level.

Near surface IP investigations: Four case studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hearst, R.B.; Morris, W.A.; Clark, M.A.

1995-12-31

The use of the Induced Polarisation (IP) method of geophysical surveying for near surface site investigations is gaining acceptance within the geophysical community. In this study the IP method is evaluated as a tool for the delineation of ground water resources; contamination plume detection in a lateritic horizon; and acid mine drainage leak detection from decommissioned mine tailings. A time domain IP system was selected for this study primarily for the flexibility in the selection and setting of receiver time windows and diagnostic characteristics attributed to submitting the data to Cole-Cole analysis. Analysis of the acquired data in conjunction withmore » available borehole and geological information illustrates the effectiveness and usefulness of the survey method for solving near surface problems. In all of the locations tested, it was found that with a properly designed IP survey it was possible to resolve the target and/or related structures.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gupta, Prabhat Kumar; Rabehl, Roger

Thermo-acoustic oscillations are a commonly observed phenomenon in helium cryogenic systems, especially in tubes connecting hot and cold areas. The open ends of these tubes are connected to the lower temperature (typically at 4.2 K), and the closed ends of these tubes are connected to the high temperature (300K). Cryogenic instrumentation installations provide ideal conditions for these oscillations to occur due to the steep temperature gradient along the tubing. These oscillations create errors in measurements as well as an undesirable heat load to the system. The work presented here develops engineering guidelines to design oscillation-free helium piping. This work alsomore » studies the effect of different piping inserts and shows how the proper geometrical combinations have to be chosen to avoid thermo-oscillations. The effect of an 80 K intercept is also studied and shows that thermo-oscillations can be dampened by placing the intercept at an appropriate location.« less

Precise interferometric tracking of the DSCS II geosynchronous orbiter

NASA Astrophysics Data System (ADS)

Border, J. S.; Donivan, F. F., Jr.; Shiomi, T.; Kawano, N.

1986-01-01

A demonstration of the precise tracking of a geosynchronous orbiter by radio metric techniques based on very-long-baseline interferometry (VLBI) has been jointly conducted by the Jet Propulsion Laboratory and Japan's Radio Research Laboratory. Simultaneous observations of a U.S. Air Force communications satellite from tracking stations in California, Australia, and Japan have determined the satellite's position with an accuracy of a few meters. Accuracy claims are based on formal statistics, which include the effects of errors in non-estimated parameters and which are supported by a chi-squared of less than one, and on the consistency of orbit solutions from disjoint data sets. A study made to assess the impact of shorter baselines and reduced data noise concludes that with a properly designed system, similar accuracy could be obtained for either a satellite viewed from stations located within the continental U.S. or for a satellite viewed from stations within Japanese territory.

Clinical Verification of Image Warping as a Potential Aid for the Visually Handicapped

NASA Technical Reports Server (NTRS)

Loshin, David

1996-01-01

The bulk of this research was to designed determine potential of the Programmable Remapper (PR) as a device to enhance vision for the visually handicapped. This research indicated that remapping would have potential as a low vision device if the eye position could be monitored with feedback to specify the proper location of the remapped image. This must be accomplished at high rate so that there is no lag of the image behind the eye position. Since at this time, there is no portable eye monitor device (at a reasonable cost) that will operate under the required conditions, it would not be feasible to continue with remapping experiments for patients with central field defects. However, since patients with peripheral field defects do not have the same eye positioning requirements, they may indeed benefit from this technology. Further investigations must be performed to determine plausibility of this application of remapping.

Assessment of Natural Ventilation System for a Typical Residential House in Poland

NASA Astrophysics Data System (ADS)

Antczak-Jarząbska, Romana; Krzaczek, Marek

2016-09-01

The paper presents the research results of field measurements campaign of natural ventilation performance and effectiveness in a residential building. The building is located in the microclimate whose parameters differ significantly in relation to a representative weather station. The measurement system recorded climate parameters and the physical variables characterizing the air flow in the rooms within 14 days of the winter season. The measurement results showed that in spite of proper design and construction of the ventilation system, unfavorable microclimatic conditions that differed from the predicted ones caused significant reduction in the efficiency of the ventilation system. Also, during some time periods, external climate conditions caused an opposite air flow direction in the vent inlets and outlets, leading to a significant deterioration of air quality and thermal comfort measured by CO2 concentration and PMV index in a residential area.

Standoff detection of explosives: critical comparison for ensuing options on Raman spectroscopy-LIBS sensor fusion.

PubMed

Moros, J; Lorenzo, J A; Laserna, J J

2011-07-01

In general, any standoff sensor for the effective detection of explosives must meet two basic requirements: first, a capacity to detect the response generated from only a small amount of material located at a distance of several meters (high sensitivity) and second, the ability to provide easily distinguishable responses for different materials (high specificity). Raman spectroscopy and laser-induced breakdown spectroscopy (LIBS) are two analytical techniques which share similar instrumentation and, at the same time, generate complementary data. These factors have been taken into account recently for the design of sensors used in the detection of explosives. Similarly, research on the proper integration of both techniques has been around for a while. A priori, the different operational conditions required by the two techniques oblige the acquisition of the response for each sensor through sequential analysis, previously necessary to define the proper hierarchy of actuation. However, such an approach does not guarantee that Raman and LIBS responses obtained may relate to each other. Nonetheless, the possible advantages arising from the integration of the molecular and elemental spectroscopic information come with an obvious underlying requirement, simultaneous data acquisition. In the present paper, strong and weak points of Raman spectroscopy and LIBS for solving explosives detection problems, in terms of selectivity, sensitivity, and throughput, are critically examined, discussed, and compared for assessing the ensuing options on the fusion of the responses of both sensing technologies.

Texas flexible pavements overlays : review and analysis of existing databases.

DOT National Transportation Integrated Search

2011-12-01

Proper calibration of pavement design and rehabilitation performance models to : conditions in Texas is essential for cost-effective flexible pavement design. The degree of : excellence with which TxDOTs pavement design models is calibrated will d...

24 CFR 3280.603 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... heat tape located on the underside of the manufactured home within 2 feet of the water supply inlet... service for a reasonable life expectancy. (2) Conservation. Water closets shall be selected and adjusted to use the minimum quantity of water consistent with proper performance and cleaning. (3) Connection...

49 CFR 213.343 - Continuous welded rail (CWR).

Code of Federal Regulations, 2012 CFR

2012-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION TRACK SAFETY STANDARDS Train Operations at Track Classes 6 and... and inspection of CWR, and a training program for the application of those procedures, which shall be... located; and (2) De-stressing procedures/methods which address proper attainment of the desired rail...

49 CFR 213.343 - Continuous welded rail (CWR).

Code of Federal Regulations, 2013 CFR

2013-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION TRACK SAFETY STANDARDS Train Operations at Track Classes 6 and... and inspection of CWR, and a training program for the application of those procedures, which shall be... located; and (2) De-stressing procedures/methods which address proper attainment of the desired rail...

49 CFR 213.343 - Continuous welded rail (CWR).

Code of Federal Regulations, 2014 CFR

2014-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION TRACK SAFETY STANDARDS Train Operations at Track Classes 6 and... and inspection of CWR, and a training program for the application of those procedures, which shall be... located; and (2) De-stressing procedures/methods which address proper attainment of the desired rail...

Proposed chemical mechanismsManagement practices impacts soil nutrients and bacterial populations in backgrounding beef feedlot

USDA-ARS?s Scientific Manuscript database

Intensive beef backgrounding often accumulate manure born soil nutrients, microbes, and pharmaceuticals at different site locations. Unless properly managed, such waste materials can pollute surrounding soil and water sources. Soil sampling from these sites helps determining waste material levels bu...

21 CFR 110.37 - Sanitary facilities and controls.

Code of Federal Regulations, 2013 CFR

2013-04-01

... HUMAN FOOD Buildings and Facilities § 110.37 Sanitary facilities and controls. Each plant shall be... water to required locations throughout the plant. (2) Properly convey sewage and liquid disposable waste from the plant. (3) Avoid constituting a source of contamination to food, water supplies, equipment, or...

21 CFR 110.37 - Sanitary facilities and controls.

Code of Federal Regulations, 2014 CFR

2014-04-01

... HUMAN FOOD Buildings and Facilities § 110.37 Sanitary facilities and controls. Each plant shall be... water to required locations throughout the plant. (2) Properly convey sewage and liquid disposable waste from the plant. (3) Avoid constituting a source of contamination to food, water supplies, equipment, or...

21 CFR 110.37 - Sanitary facilities and controls.

Code of Federal Regulations, 2012 CFR

2012-04-01

... HUMAN FOOD Buildings and Facilities § 110.37 Sanitary facilities and controls. Each plant shall be... water to required locations throughout the plant. (2) Properly convey sewage and liquid disposable waste from the plant. (3) Avoid constituting a source of contamination to food, water supplies, equipment, or...

Assessment of Agricultural Drainage Pipe Conditions Using Ground Penetrating Radar

USDA-ARS?s Scientific Manuscript database

Farmers and land improvement contractors, especially in the Midwest U.S., need methods to not only locate buried agricultural drainage pipe, but also to determine if the pipes are functioning properly with respect to water delivery. Previous investigations have already demonstrated the feasibility o...

Constitutional Reform for Conflict Management

DTIC Science & Technology

2014-04-01

conflict. Empirical studies reveal that both accommodative and integrative constitutional design can produce political stability , if properly...reform, and the ability of various constitutional designs to promote democracy and political stability .

Mechanosensory Genes Pkd1 and Pkd2 Contribute to the Planar Polarization of Brain Ventricular Epithelium

PubMed Central

Herranz-Pérez, Vicente; Nakatani, Jin; Boletta, Alessandra; García-Verdugo, José Manuel

2015-01-01

Directional beating of ependymal (E) cells' cilia in the walls of the ventricles in the brain is essential for proper CSF flow. E cells display two forms of planar cell polarity (PCP): rotational polarity of individual cilium and translational polarity (asymmetric positioning of cilia in the apical area). The orientation of individual E cells varies according to their location in the ventricular wall (location-specific PCP). It has been hypothesized that hydrodynamic forces on the apical surface of radial glia cells (RGCs), the embryonic precursors of E cells, could guide location-specific PCP in the ventricular epithelium. However, the detection mechanisms for these hydrodynamic forces have not been identified. Here, we show that the mechanosensory proteins polycystic kidney disease 1 (Pkd1) and Pkd2 are present in primary cilia of RGCs. Ablation of Pkd1 or Pkd2 in Nestin-Cre;Pkd1flox/flox or Nestin-Cre;Pkd2flox/flox mice, affected PCP development in RGCs and E cells. Early shear forces on the ventricular epithelium may activate Pkd1 and Pkd2 in primary cilia of RGCs to properly polarize RGCs and E cells. Consistently, Pkd1, Pkd2, or primary cilia on RGCs were required for the proper asymmetric localization of the PCP protein Vangl2 in E cells' apical area. Analyses of single- and double-heterozygous mutants for Pkd1 and/or Vangl2 suggest that these genes function in the same pathway to establish E cells' PCP. We conclude that Pkd1 and Pkd2 mechanosensory proteins contribute to the development of brain PCP and prevention of hydrocephalus. SIGNIFICANCE STATEMENT This study identifies key molecules in the development of planar cell polarity (PCP) in the brain and prevention of hydrocephalus. Multiciliated ependymal (E) cells within the brain ventricular epithelium generate CSF flow through ciliary beating. E cells display location-specific PCP in the orientation and asymmetric positioning of their cilia. Defects in this PCP can result in hydrocephalus. Hydrodynamic forces on radial glial cells (RGCs), the embryonic progenitors of E cells, have been suggested to guide PCP. We show that the mechanosensory proteins Pkd1 and Pkd2 localize to primary cilia in RGCs, and their ablation disrupts the development of PCP in E cells. Early shear forces on RGCs may activate Pkd1 and Pkd2 in RGCs' primary cilia to properly orient E cells. This study identifies key molecules in the development of brain PCP and prevention of hydrocephalus. PMID:26245976

Multiple spacecraft configuration designs for coordinated flight missions

NASA Astrophysics Data System (ADS)

Fumenti, Federico; Theil, Stephan

2018-06-01

Coordinated flight allows the replacement of a single monolithic spacecraft with multiple smaller ones, based on the principle of distributed systems. According to the mission objectives and to ensure a safe relative motion, constraints on the relative distances need to be satisfied. Initially, differential perturbations are limited by proper orbit design. Then, the induced differential drifts can be properly handled through corrective maneuvers. In this work, several designs are surveyed, defining the initial configuration of a group of spacecraft while counteracting the differential perturbations. For each of the investigated designs, focus is placed upon the number of deployable spacecraft and on the possibility to ensure safe relative motion through station keeping of the initial configuration, with particular attention to the required Δ V budget and the constraints violations.

A Distance Bounding Protocol for Location-Cloaked Applications

PubMed Central

Molina-Martínez, Cristián; Galdames, Patricio

2018-01-01

Location-based services (LBSs) assume that users are willing to release trustworthy and useful details about their whereabouts. However, many location privacy concerns have arisen. For location privacy protection, several algorithms build a cloaking region to hide a user’s location. However, many applications may not operate adequately on cloaked locations. For example, a traditional distance bounding protocol (DBP)—which is run by two nodes called the prover and the verifier—may conclude an untight and useless distance between these two entities. An LBS (verifier) may use this distance as a metric of usefulness and trustworthiness of the location claimed by the user (prover). However, we show that if a tight distance is desired, traditional DBP can refine a user’s cloaked location and compromise its location privacy. To find a proper balance, we propose a location-privacy-aware DBP protocol. Our solution consists of adding some small delays before submitting any user’s response. We show that several issues arise when a certain delay is chosen, and we propose some solutions. The effectiveness of our techniques in balancing location refinement and utility is demonstrated through simulation. PMID:29701641

Research on orbit prediction for solar-based calibration proper satellite

NASA Astrophysics Data System (ADS)

Chen, Xuan; Qi, Wenwen; Xu, Peng

2018-03-01

Utilizing the mathematical model of the orbit mechanics, the orbit prediction is to forecast the space target's orbit information of a certain time based on the orbit of the initial moment. The proper satellite radiometric calibration and calibration orbit prediction process are introduced briefly. On the basis of the research of the calibration space position design method and the radiative transfer model, an orbit prediction method for proper satellite radiometric calibration is proposed to select the appropriate calibration arc for the remote sensor and to predict the orbit information of the proper satellite and the remote sensor. By analyzing the orbit constraint of the proper satellite calibration, the GF-1solar synchronous orbit is chose as the proper satellite orbit in order to simulate the calibration visible durance for different satellites to be calibrated. The results of simulation and analysis provide the basis for the improvement of the radiometric calibration accuracy of the satellite remote sensor, which lays the foundation for the high precision and high frequency radiometric calibration.

Continuum definition for Ceres absorption bands at 3.1, 3.4 and 4.0 μm

NASA Astrophysics Data System (ADS)

Galiano, A.; Palomba, E.; Longobardo, A.; Zinzi, A.; De Sanctis, M. C.; Raponi, A.; Carrozzo, F. G.; Ciarniello, M.; Dirri, F.

2017-09-01

The images and hyperspectral data acquired during various Dawn mission phases (e.g. Survey, HAMO and LAMO) allowed identifying regions of different albedo on Ceres surface, where absorption bands located at 3.4 and 4.0 μm can assume different shapes. The 3.1 μm feature is observed on the entire Ceres surface except on Cerealia Facula, the brightest spot located on the dome of Occator crater. To perform a mineralogical investigation, absorption bands in reflectance spectra should be properly isolated by removing spectral continuum; hence, parameters as band centers and band depths must be estimated. The problem in the defining the continuum is in the VIR spectral range, which ends at 5.1 μm even though the reliable data, where the thermal contribution is properly removed, stops at 4.2 μm. Band shoulders located at longer wavelengths cannot be estimated. We defined different continua, with the aim to find the most appropriate to isolate the three spectral bands, whatever the region and the spatial resolution of hyperspectral images. The linear continuum seems to be the most suitable definition for our goals. Then, we performed an error evaluation on band depths and band centers introduced by this continuum definition.

Real-time registration of video with ultrasound using stereo disparity

NASA Astrophysics Data System (ADS)

Wang, Jihang; Horvath, Samantha; Stetten, George; Siegel, Mel; Galeotti, John

2012-02-01

Medical ultrasound typically deals with the interior of the patient, with the exterior left to the original medical imaging modality, direct human vision. For the human operator scanning the patient, the view of the external anatomy is essential for correctly locating the ultrasound probe on the body and making sense of the resulting ultrasound images in their proper anatomical context. The operator, after all, is not expected to perform the scan with his eyes shut. Over the past decade, our laboratory has developed a method of fusing these two information streams in the mind of the operator, the Sonic Flashlight, which uses a half silvered mirror and miniature display mounted on an ultrasound probe to produce a virtual image within the patient at its proper location. We are now interested in developing a similar data fusion approach within the ultrasound machine itself, by, in effect, giving vision to the transducer. Our embodiment of this concept consists of an ultrasound probe with two small video cameras mounted on it, with software capable of locating the surface of an ultrasound phantom using stereo disparity between the two video images. We report its first successful operation, demonstrating a 3D rendering of the phantom's surface with the ultrasound data superimposed at its correct relative location. Eventually, automated analysis of these registered data sets may permit the scanner and its associated computational apparatus to interpret the ultrasound data within its anatomical context, much as the human operator does today.

The Essentials of Proper Wine Service.

ERIC Educational Resources Information Center

Manago, Gary H.

This instructional unit was designed to assist the food services instructor and/or the restaurant manager in training students and/or staff in the proper procedure for serving wines to guests. The lesson plans included in this unit focus on: (1) the different types of wine glasses and their uses; (2) the parts of a wine glass; (3) the proper…

Designing a Competency-Based New County Extension Personnel Training Program: A Novel Approach

ERIC Educational Resources Information Center

Brodeur, Cheri Winton; Higgins, Cynthia; Galindo-Gonzalez, Sebastian; Craig, Diane D.; Haile, Tyann

2011-01-01

Voluntary county personnel turnover occurs for a multitude of reasons, including the lack of job satisfaction, organizational commitment, and job embeddedness and lack of proper training. Loss of personnel can be costly both economically and in terms of human capital. Retention of Extension professionals can be improved through proper training or…

Toward a framework for computer-mediated collaborative design in medical informatics.

PubMed

Patel, V L; Kaufman, D R; Allen, V G; Shortliffe, E H; Cimino, J J; Greenes, R A

1999-09-01

The development and implementation of enabling tools and methods that provide ready access to knowledge and information are among the central goals of medical informatics. The need for multi-institutional collaboration in the development of such tools and methods is increasingly being recognized. Collaboration involves communication, which typically involves individuals who work together at the same location. With the evolution of electronic modalities for communication, we seek to understand the role that such technologies can play in supporting collaboration, especially when the participants are geographically separated. Using the InterMed Collaboratory as a subject of study, we have analyzed their activities as an exercise in computer- and network-mediated collaborative design. We report on the cognitive, sociocultural, and logistical issues encountered when scientists from diverse organizations and backgrounds use communications technologies while designing and implementing shared products. Results demonstrate that it is important to match carefully the content with the mode of communication, identifying, for example, suitable uses of E-mail, conference calls, and face-to-face meetings. The special role of leaders in guiding and facilitating the group activities can also be seen, regardless of the communication setting in which the interactions occur. Most important is the proper use of technology to support the evolution of a shared vision of group goals and methods, an element that is clearly necessary before successful collaborative designs can proceed.

32 CFR 552.103 - Requirements for carrying and use.

Code of Federal Regulations, 2011 CFR

2011-07-01

... by the most direct route to approved range or to the location where the weapon is to be sold or...., projectiles physically separated from the firearms, not just removed from the chamber), except when actually... on approved firing range when properly authorized). (4) Persons not affiliated with DOD or this...

32 CFR 552.103 - Requirements for carrying and use.

Code of Federal Regulations, 2012 CFR

2012-07-01

... by the most direct route to approved range or to the location where the weapon is to be sold or...., projectiles physically separated from the firearms, not just removed from the chamber), except when actually... on approved firing range when properly authorized). (4) Persons not affiliated with DOD or this...

32 CFR 552.103 - Requirements for carrying and use.

Code of Federal Regulations, 2013 CFR

2013-07-01

... by the most direct route to approved range or to the location where the weapon is to be sold or...., projectiles physically separated from the firearms, not just removed from the chamber), except when actually... on approved firing range when properly authorized). (4) Persons not affiliated with DOD or this...

32 CFR 552.103 - Requirements for carrying and use.

Code of Federal Regulations, 2014 CFR

2014-07-01

... by the most direct route to approved range or to the location where the weapon is to be sold or...., projectiles physically separated from the firearms, not just removed from the chamber), except when actually... on approved firing range when properly authorized). (4) Persons not affiliated with DOD or this...

METHODS DEVELOPMENT AT THE NEAR LAB ECOLOGICAL RESEARCH AREA (NLERA) LOCATED IN THE NEUSE RIVER BASIN.

EPA Science Inventory

This task supports the Agency's efforts on developing a proper risk assessment tools to address Ecological and eventually Human exposures. The Agency needs to be able to identify, measure and estimate ecosystem exposure to multiple stressors. The research under this task suppor...

14 CFR 23.807 - Emergency exits.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Emergency exits must not be located with respect to any propeller disk or any other potential hazard so as... airplanes certificated for spinning, allow each occupant to abandon the airplane at the highest speed likely to be achieved in the maneuver for which the airplane is certificated. (c) Tests. The proper...

46 CFR 127.430 - Visibility from pilothouse.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ARRANGEMENTS Construction of Windows, Visibility, and Operability of Coverings § 127.430 Visibility from pilothouse. (a) Windows and other openings at the pilothouse must be of sufficient size and properly located... used in windows at the pilothouse must have a light transmission of at least 70 percent according to...

Validity Semantics in Educational and Psychological Assessment

ERIC Educational Resources Information Center

Hathcoat, John D.

2013-01-01

The semantics, or meaning, of validity is a fluid concept in educational and psychological testing. Contemporary controversies surrounding this concept appear to stem from the proper location of validity. Under one view, validity is a property of score-based inferences and entailed uses of test scores. This view is challenged by the…

49 CFR 230.87 - Cab lights.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Cab lights. 230.87 Section 230.87 Transportation... Signals, Sanders and Lights § 230.87 Cab lights. Each steam locomotive shall have cab lights that... readings from their usual and proper positions in the cab. These lights shall be so located and constructed...

49 CFR 230.87 - Cab lights.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Cab lights. 230.87 Section 230.87 Transportation... Signals, Sanders and Lights § 230.87 Cab lights. Each steam locomotive shall have cab lights that... readings from their usual and proper positions in the cab. These lights shall be so located and constructed...

49 CFR 230.87 - Cab lights.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Cab lights. 230.87 Section 230.87 Transportation... Signals, Sanders and Lights § 230.87 Cab lights. Each steam locomotive shall have cab lights that... readings from their usual and proper positions in the cab. These lights shall be so located and constructed...

49 CFR 230.87 - Cab lights.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Cab lights. 230.87 Section 230.87 Transportation... Signals, Sanders and Lights § 230.87 Cab lights. Each steam locomotive shall have cab lights that... readings from their usual and proper positions in the cab. These lights shall be so located and constructed...

49 CFR 230.87 - Cab lights.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Cab lights. 230.87 Section 230.87 Transportation... Signals, Sanders and Lights § 230.87 Cab lights. Each steam locomotive shall have cab lights that... readings from their usual and proper positions in the cab. These lights shall be so located and constructed...

The applied technologies to access clean water for remote communities

NASA Astrophysics Data System (ADS)

Rabindra, I. B.

2018-01-01

A lot of research is done to overcome the remote communities to access clean water, yet very little is utilized and implemented by the community. Various reasons can probably be made for, which is the application of research results is assessed less practical. The aims of this paper is seeking a practical approach, how to establish criteria for the design can be easier applied, at the proper locations, the simple construction, effectively producing a volume and quality of clean water designation. The methods used in this paper is a technological model assessment of treatment/filtering clean water produced a variety of previous research, to establish a model of appropriate technology for remote communities. Various research results collected from the study of literature, while the identification of opportunities and threats to its application is done using a SWOT analysis. This article discussion is looking for alternative models of clean water filtration technology from the previous research results, to be selected as appropriate technology, easily applied and bring of many benefits to the remote communities. The conclusions resulting from the discussion in this paper, expected to be used as the basic criteria of design model of clean water filtration technologies that can be accepted and applied effectively by the remote communities.

Silicon sensors for catheters and guide wires

NASA Astrophysics Data System (ADS)

Goosen, Hans F.

2001-11-01

One area that can make use of the miniature size of present day micro electromechanical systems (MEMS) is that of the medical field of minimally invasive interventions. These procedures, used for both diagnosis and treatment, use catheters that are advanced through the blood vessels deep into the body, without the need for surgery. However, once inside the body, the doctor performing the procedure is completely reliant on the information the catheter(s) can provide in addition to the projection imaging of a fluoroscope. A good range of sensors for catheters is required for a proper diagnosis. To this end, miniature sensors are being developed to be fitted to catheters and guide wires. As the accurate positioning of these instruments is problematic, it is necessary to combine several sensors on the same guide wire or catheter to measure several parameters in the same location. This however, brings many special problems to the design of the sensors, such as small size, low power consumption, bio-compatibility of materials, robust design for patient safety, a limited number of connections, packaging, etc. This paper will go into both the advantages and design problems of micromachined sensors and actuators in catheters and guide wires. As an example, a multi parameter blood sensor, measuring flow velocity, pressure and oxygen saturation, will be discussed.

Transport of thermal water from well to thermal baths

NASA Astrophysics Data System (ADS)

Montegrossi, Giordano; Vaselli, Orlando; Tassi, Franco; Nocentini, Matteo; Liccioli, Caterina; Nisi, Barbara

2013-04-01

The main problem in building a thermal bath is having a hot spring or a thermal well located in an appropriate position for customer access; since Roman age, thermal baths were distributed in the whole empire and often road and cities were built all around afterwards. Nowadays, the perspectives are changed and occasionally the thermal resource is required to be transported with a pipeline system from the main source to the spa. Nevertheless, the geothermal fluid may show problems of corrosion and scaling during transport. In the Ambra valley, central Italy, a geothermal well has recently been drilled and it discharges a Ca(Mg)-SO4, CO2-rich water at the temperature of 41 °C, that could be used for supplying a new spa in the surrounding areas of the well itself. The main problem is that the producing well is located in a forest tree ca. 4 km far away from the nearest structure suitable to host the thermal bath. In this study, we illustrate the pipeline design from the producing well to the spa, constraining the physical and geochemical parameters to reduce scaling and corrosion phenomena. The starting point is the thermal well that has a flow rate ranging from 22 up to 25 L/sec. The thermal fluid is heavily precipitating calcite (50-100 ton/month) due to the calcite-CO2 equilibrium in the reservoir, where a partial pressure of 11 bar of CO2 is present. One of the most vexing problems in investigating scaling processed during the fluid transport in the pipeline is that there is not a proper software package for multiphase fluid flow in pipes characterized by such a complex chemistry. As a consequence, we used a modified TOUGHREACT with Pitzer database, arranged to use Darcy-Weisbach equation, and applying "fictitious" material properties in order to give the proper y- z- velocity profile in comparison to the analytical solution for laminar fluid flow in pipes. This investigation gave as a result the lowest CO2 partial pressure to be kept in the pipeline (nearly 2.5 bar) to avoid uncontrolled calcite precipitation, and accordingly the pipeline path was designed. Non-linear phenomena that may originate calcite precipitation, such as phase separation and pressure waves, were discussed. The pipeline and the thermal bath are planned to be built next year.

In use performance of catalytic converters on properly maintained high mileage vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabourin, M.A.; Larson, R.E.; Donahue, K.S.

1986-01-01

A test program to evaluate the performance of catalytic converters from fifty-six 1981 and 1982 model year high mileage properly maintained in-use vehicles (from 21 engine families) was performed by the Certification Division of the Office of Mobile Sources (EPA). The program is called the Catalyst Change Program. All program vehicles were screened for proper maintenance and for mileages that ranged from 35,000 to 60,000 miles. Among vehicles belonging to 21 high sales volume and high technology engine and emission control system designs tested, poor catalyst performance was determined to be a significant contributor to emissions failure of properly-maintained vehiclesmore » at or near their warranted useful life mileage.« less

Experimental design for estimating unknown groundwater pumping using genetic algorithm and reduced order model

NASA Astrophysics Data System (ADS)

Ushijima, Timothy T.; Yeh, William W.-G.

2013-10-01

An optimal experimental design algorithm is developed to select locations for a network of observation wells that provide maximum information about unknown groundwater pumping in a confined, anisotropic aquifer. The design uses a maximal information criterion that chooses, among competing designs, the design that maximizes the sum of squared sensitivities while conforming to specified design constraints. The formulated optimization problem is non-convex and contains integer variables necessitating a combinatorial search. Given a realistic large-scale model, the size of the combinatorial search required can make the problem difficult, if not impossible, to solve using traditional mathematical programming techniques. Genetic algorithms (GAs) can be used to perform the global search; however, because a GA requires a large number of calls to a groundwater model, the formulated optimization problem still may be infeasible to solve. As a result, proper orthogonal decomposition (POD) is applied to the groundwater model to reduce its dimensionality. Then, the information matrix in the full model space can be searched without solving the full model. Results from a small-scale test case show identical optimal solutions among the GA, integer programming, and exhaustive search methods. This demonstrates the GA's ability to determine the optimal solution. In addition, the results show that a GA with POD model reduction is several orders of magnitude faster in finding the optimal solution than a GA using the full model. The proposed experimental design algorithm is applied to a realistic, two-dimensional, large-scale groundwater problem. The GA converged to a solution for this large-scale problem.

Quantum logic gates based on coherent electron transport in quantum wires.

PubMed

Bertoni, A; Bordone, P; Brunetti, R; Jacoboni, C; Reggiani, S

2000-06-19

It is shown that the universal set of quantum logic gates can be realized using solid-state quantum bits based on coherent electron transport in quantum wires. The elementary quantum bits are realized with a proper design of two quantum wires coupled through a potential barrier. Numerical simulations show that (a) a proper design of the coupling barrier allows one to realize any one-qbit rotation and (b) Coulomb interaction between two qbits of this kind allows the implementation of the CNOT gate. These systems are based on a mature technology and seem to be integrable with conventional electronics.

Optimum bus headway for preemption : a simulation approach

DOT National Transportation Integrated Search

1997-01-01

Preemption techniques are designed to provide preferential treatment for buses at signalized intersections. A preemption strategy, if properly designed, can provide continuous green phases for buses at successive intersections, thereby reducing trave...

Organizing a breast cancer database: data management.

PubMed

Yi, Min; Hunt, Kelly K

2016-06-01

Developing and organizing a breast cancer database can provide data and serve as valuable research tools for those interested in the etiology, diagnosis, and treatment of cancer. Depending on the research setting, the quality of the data can be a major issue. Assuring that the data collection process does not contribute inaccuracies can help to assure the overall quality of subsequent analyses. Data management is work that involves the planning, development, implementation, and administration of systems for the acquisition, storage, and retrieval of data while protecting it by implementing high security levels. A properly designed database provides you with access to up-to-date, accurate information. Database design is an important component of application design. If you take the time to design your databases properly, you'll be rewarded with a solid application foundation on which you can build the rest of your application.

Integrated engine-generator concept for aircraft electric secondary power

NASA Technical Reports Server (NTRS)

Secunde, R. R.; Macosko, R. P.; Repas, D. S.

1972-01-01

The integrated engine-generator concept of locating an electric generator inside an aircraft turbojet or turbofan engine concentric with, and driven by, one of the main engine shafts is discussed. When properly rated, the generator can serve as an engine starter as well as a generator of electric power. The electric power conversion equipment and generator controls are conveniently located in the aircraft. Preliminary layouts of generators in a large engine together with their physical sizes and weights indicate that this concept is a technically feasible approach to aircraft secondary power.

Integrated engine generator for aircraft secondary power

NASA Technical Reports Server (NTRS)

Secunde, R. R.

1972-01-01

An integrated engine-generator for aircraft secondary power generation is described. The concept consists of an electric generator located inside a turbojet or turbofan engine and both concentric with and driven by one of the main engine shafts. The electric power conversion equipment and generator controls are located in the aircraft. When properly rated, the generator serves as an engine starter as well as a source of electric power. This configuration reduces or eliminates the need for an external gear box on the engine and permits reduction in the nacelle diameter.

Identification of potential locations of electric vehicle supply equipment

NASA Astrophysics Data System (ADS)

Brooker, R. Paul; Qin, Nan

2015-12-01

Proper placement of electric vehicle supply equipment (charging stations) requires an understanding of vehicle usage patterns. Using data from the National Household Travel Survey on vehicle mileage and destination patterns, analyses were performed to determine electric vehicles' charging needs, as a function of battery size and state of charge. This paper compares electric vehicle charging needs with Department of Energy electric vehicle charging data from real-world charging infrastructure. By combining the electric vehicles charging needs with charging data from real-world applications, locations with high electric vehicle charging likelihood are identified.

Radon mitigation in cold climates at Kitigan Zibi Anishinabeg.

PubMed

Brossard, Mathieu; Ottawa, Céline Brazeau; Falcomer, Renato; Whyte, Jeff

2015-02-01

Available radon mitigation results were gathered for 85 houses mainly by installing sub-slab depressurization systems (SSDS) with two types of discharge and fan locations: Above ground level discharge with the fan located in the basement (AGL) or above roof line discharge with the fan located in the attic (ARL). A comparative analysis was made of mitigation efficiency and of exhaust icing. Results show that both SSDS scenarios reduced radon levels similarly. The results of SSDS with AGL show that a sealed radon fan having proper fittings and sealed piping was able to reduce the radon to acceptable levels, and that these installations were less subject to obstructive icing of the exhaust in cold climates.

Lighting for Schools.

ERIC Educational Resources Information Center

Benya, James R.

This publication highlights some of the benefits of proper daylighting design in educational facilities, discusses energy efficient electric lighting choices schools can make that are long lasting and require little maintenance, and offers six steps for designing lighting systems that use half the energy of earlier conventional designs. Several…

Evaluation of hot mix asphalt moisture sensitivity using the Nottingham Asphalt test equipment : final report, March 2010.

DOT National Transportation Integrated Search

2010-03-01

Pavements are subjected to different stresses during their design lives. A properly designed pavement will perform adequately during its : design life, and the distresses will not exceed the allowable limits; however, there are several factures that ...

Recreating Liberal Education: Student-Designed Programming after a Decade.

ERIC Educational Resources Information Center

Smith, Mark; Clarke, John

1980-01-01

Though student-designed programs have been justified by references to humanism, systems theory, and romantic idealism, a more secure foundation lies in developmental theory. When properly advised, it is suggested, student-designed programs resemble the most desirable processes of liberal education. (Author/MLW)

46 CFR 58.30-5 - Design requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Design requirements. 58.30-5 Section 58.30-5 Shipping... AND RELATED SYSTEMS Fluid Power and Control Systems § 58.30-5 Design requirements. (a) The.... (b) The system shall be so designed that proper functioning of any unit shall not be affected by the...

46 CFR 58.30-5 - Design requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Design requirements. 58.30-5 Section 58.30-5 Shipping... AND RELATED SYSTEMS Fluid Power and Control Systems § 58.30-5 Design requirements. (a) The.... (b) The system shall be so designed that proper functioning of any unit shall not be affected by the...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 12 2013-01-01 2013-01-01 false Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 12 2012-01-01 2012-01-01 false Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 12 2011-01-01 2011-01-01 false Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

7 CFR Exhibit B to Subpart C of... - Site Development Design Requirements

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 12 2014-01-01 2013-01-01 true Site Development Design Requirements B Exhibit B to... Work Pt. 1924, Subpt. C, Exh. B Exhibit B to Subpart C of Part 1924—Site Development Design... burdens and conditions unsuitable for healthy and pleasant living. Proper site design can preserve...

Design for Review - Applying Lessons Learned to Improve the FPGA Review Process

NASA Technical Reports Server (NTRS)

Figueiredo, Marco A.; Li, Kenneth E.

2014-01-01

Flight Field Programmable Gate Array (FPGA) designs are required to be independently reviewed. This paper provides recommendations to Flight FPGA designers to properly prepare their designs for review in order to facilitate the review process, and reduce the impact of the review time in the overall project schedule.

Considerations for the Optimal Design of a Two-Way Interactive Distance Education Classroom.

ERIC Educational Resources Information Center

Gregg, Joe; Persichitte, Kay

To make effective use of a two-way interactive distance education system, classroom design should be a primary consideration. A properly designed classroom will enhance content objectives and increase acceptance of this type of instructional delivery. This paper describes key considerations for optimal design. Construction considerations include…

Ares Upper Stage Processes to Implement Model Based Design - Going Paperless

NASA Technical Reports Server (NTRS)

Gregory, Melanie

2012-01-01

Computer-Aided Design (CAD) has all but replaced the drafting board for design work. Increased productivity and accuracy should be natural outcomes of using CAD. Going from paper drawings only to paper drawings based on CAD models to CAD models and no drawings, or Model Based Design (MBD), is a natural progression in today?s world. There are many advantages to MBD over traditional design methods. To make the most of those advantages, standards should be in place and the proper foundation should be laid prior to transitioning to MBD. However, without a full understanding of the implications of MBD and the proper control of the data, the advantages are greatly diminished. Transitioning from a paper design world to an electronic design world means re-thinking how information gets controlled at its origin and distributed from one point to another. It means design methodology is critical, especially for large projects. It means preparation of standardized parts and processes as well as strong communication between all parties in order to maximize the benefits of MBD.

Manufacturing and Cost Considerations in Multidisciplinary Aircraft Design (Research on Mathematical Modeling of Manufacturability Factors)

NASA Technical Reports Server (NTRS)

Rais-Rohani, Masoud

1996-01-01

The identification of airframe Manufacturability Factors/Cost Drivers (MFCD) and the method by which the relationships between MFCD and designer-controlled parameters could be properly modeled are described.

New Evidence for the Dynamical Decay of a Multiple System in the Orion Kleinmann–Low Nebula

DOE Office of Scientific and Technical Information (OSTI.GOV)

Luhman, K. L.; Robberto, M.; Gabellini, M. Giulia Ubeira

We have measured astrometry for members of the Orion Nebula Cluster with images obtained in 2015 with the Wide Field Camera 3 on board the Hubble Space Telescope . By comparing those data to previous measurements with the Near-Infrared Camera and Multi-Object Spectrometer on Hubble in 1998, we have discovered that a star in the Kleinmann–Low Nebula, source x from Lonsdale et al., is moving with an unusually high proper motion of 29 mas yr{sup −1}, which corresponds to 55 km s{sup −1} at the distance of Orion. Previous radio observations have found that three other stars in the Kleinmann–Lowmore » Nebula (the Becklin–Neugebauer object and sources I and n) have high proper motions (5–14 mas yr{sup −1}) and were near a single location ∼540 years ago, and thus may have been members of a multiple system that dynamically decayed. The proper motion of source x is consistent with ejection from that same location 540 years ago, which provides strong evidence that the dynamical decay did occur and that the runaway star BN originated in the Kleinmann–Low Nebula rather than the nearby Trapezium cluster. However, our constraint on the motion of source n is significantly smaller than the most recent radio measurement, which indicates that it did not participate in the event that ejected the other three stars.« less

New Evidence for the Dynamical Decay of a Multiple System in the Orion Kleinmann-Low Nebula

NASA Astrophysics Data System (ADS)

Luhman, K. L.; Robberto, M.; Tan, J. C.; Andersen, M.; Giulia Ubeira Gabellini, M.; Manara, C. F.; Platais, I.; Ubeda, L.

2017-03-01

We have measured astrometry for members of the Orion Nebula Cluster with images obtained in 2015 with the Wide Field Camera 3 on board the Hubble Space Telescope. By comparing those data to previous measurements with the Near-Infrared Camera and Multi-Object Spectrometer on Hubble in 1998, we have discovered that a star in the Kleinmann-Low Nebula, source x from Lonsdale et al., is moving with an unusually high proper motion of 29 mas yr-1, which corresponds to 55 km s-1 at the distance of Orion. Previous radio observations have found that three other stars in the Kleinmann-Low Nebula (the Becklin-Neugebauer object and sources I and n) have high proper motions (5-14 mas yr-1) and were near a single location ˜540 years ago, and thus may have been members of a multiple system that dynamically decayed. The proper motion of source x is consistent with ejection from that same location 540 years ago, which provides strong evidence that the dynamical decay did occur and that the runaway star BN originated in the Kleinmann-Low Nebula rather than the nearby Trapezium cluster. However, our constraint on the motion of source n is significantly smaller than the most recent radio measurement, which indicates that it did not participate in the event that ejected the other three stars. Based on observations made with the NASA/ESA Hubble Space Telescope and the NASA Infrared Telescope Facility.

Prime Focus Spectrograph for the Subaru telescope: massively multiplexed optical and near-infrared fiber spectrograph

NASA Astrophysics Data System (ADS)

Sugai, Hajime; Tamura, Naoyuki; Karoji, Hiroshi; Shimono, Atsushi; Takato, Naruhisa; Kimura, Masahiko; Ohyama, Youichi; Ueda, Akitoshi; Aghazarian, Hrand; de Arruda, Marcio Vital; Barkhouser, Robert H.; Bennett, Charles L.; Bickerton, Steve; Bozier, Alexandre; Braun, David F.; Bui, Khanh; Capocasale, Christopher M.; Carr, Michael A.; Castilho, Bruno; Chang, Yin-Chang; Chen, Hsin-Yo; Chou, Richard C. Y.; Dawson, Olivia R.; Dekany, Richard G.; Ek, Eric M.; Ellis, Richard S.; English, Robin J.; Ferrand, Didier; Ferreira, Décio; Fisher, Charles D.; Golebiowski, Mirek; Gunn, James E.; Hart, Murdock; Heckman, Timothy M.; Ho, Paul T. P.; Hope, Stephen; Hovland, Larry E.; Hsu, Shu-Fu; Hu, Yen-Shan; Huang, Pin Jie; Jaquet, Marc; Karr, Jennifer E.; Kempenaar, Jason G.; King, Matthew E.; le Fèvre, Olivier; Mignant, David Le; Ling, Hung-Hsu; Loomis, Craig; Lupton, Robert H.; Madec, Fabrice; Mao, Peter; Souza Marrara, Lucas; Ménard, Brice; Morantz, Chaz; Murayama, Hitoshi; Murray, Graham J.; Cesar de Oliveira, Antonio; Mendes de Oliveira, Claudia; Souza de Oliveira, Ligia; Orndorff, Joe D.; de Paiva Vilaça, Rodrigo; Partos, Eamon J.; Pascal, Sandrine; Pegot-Ogier, Thomas; Reiley, Daniel J.; Riddle, Reed; Santos, Leandro; dos Santos, Jesulino Bispo; Schwochert, Mark A.; Seiffert, Michael D.; Smee, Stephen A.; Smith, Roger M.; Steinkraus, Ronald E.; Sodré, Laerte; Spergel, David N.; Surace, Christian; Tresse, Laurence; Vidal, Clément; Vives, Sebastien; Wang, Shiang-Yu; Wen, Chih-Yi; Wu, Amy C.; Wyse, Rosie; Yan, Chi-Hung

2015-07-01

The Prime Focus Spectrograph (PFS) is an optical/near-infrared multifiber spectrograph with 2394 science fibers distributed across a 1.3-deg diameter field of view at the Subaru 8.2-m telescope. The wide wavelength coverage from 0.38 μm to 1.26 μm, with a resolving power of 3000, simultaneously strengthens its ability to target three main survey programs: cosmology, galactic archaeology and galaxy/AGN evolution. A medium resolution mode with a resolving power of 5000 for 0.71 μm to 0.89 μm will also be available by simply exchanging dispersers. We highlight some of the technological aspects of the design. To transform the telescope focal ratio, a broad-band coated microlens is glued to each fiber tip. A higher transmission fiber is selected for the longest part of the cable system, optimizing overall throughput; a fiber with low focal ratio degradation is selected for the fiber-positioner and fiber-slit components, minimizing the effects of fiber movements and fiber bending. Fiber positioning will be performed by a positioner consisting of two stages of piezo-electric rotary motors. The positions of these motors are measured by taking an image of artificially back-illuminated fibers with the metrology camera located in the Cassegrain container; the fibers are placed in the proper location by iteratively measuring and then adjusting the positions of the motors. Target light reaches one of the four identical fast-Schmidt spectrograph modules, each with three arms. The PFS project has passed several project-wide design reviews and is now in the construction phase.

76 FR 37953 - Standards of Performance for Stationary Compression Ignition and Spark Ignition Internal...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-28

... problems. Moreover, the use of SCR entails the supply, storage and use of a chemical reductant, usually..., storage and handling of the chemical reductant would be greater than for engines located elsewhere in the... proper availability of the chemical reductant during the harsh winter months, new heated storage vessels...

49 CFR 230.56 - Water glass lamps.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Water glass lamps. 230.56 Section 230.56... Water Glasses and Gauge Cocks § 230.56 Water glass lamps. All water glasses must be supplied with a suitable lamp properly located to enable the engine crew to easily see the water in the glass. Injectors...

49 CFR 230.56 - Water glass lamps.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Water glass lamps. 230.56 Section 230.56... Water Glasses and Gauge Cocks § 230.56 Water glass lamps. All water glasses must be supplied with a suitable lamp properly located to enable the engine crew to easily see the water in the glass. Injectors...

Forum Guide to Elementary/Secondary Virtual Education Data. NFES 2016-095

ERIC Educational Resources Information Center

National Forum on Education Statistics, 2015

2015-01-01

When properly employed, technology may enhance and support learning opportunities available to any student, at any location, and at any time. Determining which instructional and delivery methods are best for a specific individual, group of students, community, or circumstance demands that high-quality data be available to students, parents,…

A New Kind of English: Cultural Variance, Citizenship and DiY Politics amongst the Exodus Collective in England

ERIC Educational Resources Information Center

Blackstone, Lee Robert

2005-01-01

This article addresses the construction of citizenship in contemporary England as a boundary between "proper" and "improper" English behavior. Through an ethnographic study of the Exodus Collective, a Rastafarian-anarchist community that was located north of London, I show that constructing citizenship also constructs…

Method for the melting of metals

DOEpatents

White, Jack C.; Traut, Davis E.

1992-01-01

A method of quantitatively determining the molten pool configuration in melting of metals. The method includes the steps of introducing hafnium metal seeds into a molten metal pool at intervals to form ingots, neutron activating the ingots and determining the hafnium location by radiometric means. Hafnium possesses exactly the proper metallurgical and radiochemical properties for this use.

49 CFR 230.56 - Water glass lamps.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Water glass lamps. 230.56 Section 230.56... Water Glasses and Gauge Cocks § 230.56 Water glass lamps. All water glasses must be supplied with a suitable lamp properly located to enable the engine crew to easily see the water in the glass. Injectors...

49 CFR 230.56 - Water glass lamps.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Water glass lamps. 230.56 Section 230.56... Water Glasses and Gauge Cocks § 230.56 Water glass lamps. All water glasses must be supplied with a suitable lamp properly located to enable the engine crew to easily see the water in the glass. Injectors...

The Field: The Proper Location for Methods Courses.

ERIC Educational Resources Information Center

Cardarelli, Aldo F.

1981-01-01

The position taken here is that extensive field work with children which is built around a particular set of competencies which the university student is responsible to demonstrate will accomplish far more than the campus-centered, inferentially-based lecture approach. Such a program operating at an urban university is outlined. (Author/SJL)

Preparing sites for pine plantings in South Florida

Treesearch

James W. McMinn

1969-01-01

Typical slash pine and South Florida slash pine were planted on prepared flatwoods sites at three Florida locations. Site preparation treatments were burning, strip-chopping, double-chopping, clearing, and bedding. Results through the fifth year show that bedding provided the most favorable site for early growth, and that properly planted seedlings survived no better...

Successful Keyword Searching: Initiating Research on Popular Topics Using Electronic Databases.

ERIC Educational Resources Information Center

MacDonald, Randall M.; MacDonald, Susan Priest

Students are using electronic resources more than ever before to locate information for assignments. Without the proper search terms, results are incomplete, and students are frustrated. Using the keywords, key people, organizations, and Web sites provided in this book and compiled from the most commonly used databases, students will be able to…

49 CFR 230.56 - Water glass lamps.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Water glass lamps. 230.56 Section 230.56... Water Glasses and Gauge Cocks § 230.56 Water glass lamps. All water glasses must be supplied with a suitable lamp properly located to enable the engine crew to easily see the water in the glass. Injectors...

Nighttime visibility of 3M AWP and 3M 380WR ES durable tape under dry, wet, and rainy conditions : executive summary report.

DOT National Transportation Integrated Search

2012-05-01

Pavement markings play an important role in providing visual guidance to motorists. They are used to delineate the intended travel path and guide drivers regarding their location on the road. In order to function properly, pavement markings must be v...

Estimating Anthropometric Marker Locations from 3-D LADAR Point Clouds

DTIC Science & Technology

2011-06-01

http://perception.inrialpes. fr/Publications/2008/CMKBH08. [17] Da Vinci , L. The Notebooks of Leonardo Da Vinci Complete. Public Domain, 2004. [18] Duda...the problem is based on historical research into the proper proportioning of the human body. A famous example of this research is Leonardo da Vinci’s

VizieR Online Data Catalog: OGLE II Galactic center proper motions (Sumi+, 2004)

NASA Astrophysics Data System (ADS)

Sumi, T.; Wu, X.; Udalski, A.; Szymanski, M.; Kubiak, M.; Pietrzynski, G.; Soszynski, I.; Wozniak, P.; Zebrun, K.; Szewczyk, O.; Wyrzykowski, L.

2004-07-01

We use the data collected during the second phase of the OGLE experiment, between 1997 and 2000. All observations were made with the 1.3-m Warsaw telescope located at the Las Campanas Observatory, Chile, which is operated by the Carnegie Institution of Washington. (3 data files).

Quantifying Migration Behaviour Using Net Squared Displacement Approach: Clarifications and Caveats.

PubMed

Singh, Navinder J; Allen, Andrew M; Ericsson, Göran

2016-01-01

Estimating migration parameters of individuals and populations is vital for their conservation and management. Studies on animal movements and migration often depend upon location data from tracked animals and it is important that such data are appropriately analyzed for reliable estimates of migration and effective management of moving animals. The Net Squared Displacement (NSD) approach for modelling animal movement is being increasingly used as it can objectively quantify migration characteristics and separate different types of movements from migration. However, the ability of NSD to properly classify the movement patterns of individuals has been criticized and issues related to study design arise with respect to starting locations of the data/animals, data sampling regime and extent of movement of species. We address the issues raised over NSD using tracking data from 319 moose (Alces alces) in Sweden. Moose is an ideal species to test this approach, as it can be sedentary, nomadic, dispersing or migratory and individuals vary in their extent, timing and duration of migration. We propose a two-step process of using the NSD approach by first classifying movement modes using mean squared displacement (MSD) instead of NSD and then estimating the extent, duration and timing of migration using NSD. We show that the NSD approach is robust to the choice of starting dates except when the start date occurs during the migratory phase. We also show that the starting location of the animal has a marginal influence on the correct quantification of migration characteristics. The number of locations per day (1-48) did not significantly affect the performance of non-linear mixed effects models, which correctly distinguished migration from other movement types, however, high-resolution data had a significant negative influence on estimates for the timing of migrations. The extent of movement, however, had an effect on the classification of movements, and individuals undertaking short- distance migrations can be misclassified as other movements such as sedentary or nomadic. Our study raises important considerations for designing, analysing and interpreting movement ecology studies, and how these should be determined by the biology of the species and the ecological and conservation questions in focus.

How do ensembles occupy space?

NASA Astrophysics Data System (ADS)

Daffertshofer, A.

2008-04-01

To find an answer to the title question, an attractiveness function between agents and locations is introduced yielding a phenomenological but generic model for the search for optimal distributions of agents over space. Agents can be seen as, e.g., members of biological populations like colonies of bacteria, swarms, and so on. The global attractiveness between agents and locations is maximized causing (self-propelled) `motion' of agents and, eventually, distinct distributions of agents over space. At the same token spontaneous changes or `decisions' are realized via competitions between agents as well as between locations. Hence, the model's solutions can be considered a sequence of decisions of agents during their search for a proper location. Depending on initial conditions both optimal as well as suboptimal configurations can be reached. For the latter early decision-making are important for avoiding possible conflicts: if the proper moment is missed, then only a few agents can find an optimal solution. Indeed, there is a delicate interplay between the values of the attractiveness function and the constraints as can be expressed by distinct terms of a potential function containing different Lagrange parameters. The model should be viewed as a top-down approach as it describes the dynamics of order parameters, i.e. macroscopic variables that reflect affiliations between agents and locations. The dynamics, however, is modified via so-called cost functions that are interpreted in terms of affinity levels. This interpretation can be seen as an original step towards an understanding of the dynamics at the underlying microscopic level. When focusing on the agent, one may say that the dynamics of an order parameter shows the evolution of an agent's intrinsic `map' for solving the problem of space occupation. Importantly, the dynamics does not necessarily distinguish between evolving (or moving) agents and evolving (or moving) locations though agents are more likely to be actors than the locations. Put differently, an order parameter describes an internal map which is linked to the expectation of an agent to find a certain location. Owing to the dynamical representation, we can therefore follow up the change of these maps over time leading from uncertainty to certainty.

Computational Design Tool for Bridge Hydrodynamic Loading in Inundated Flows of Midwest Rivers

DOT National Transportation Integrated Search

2009-12-01

The hydraulic forces experienced by an inundated bridge deck have great importance in the design of bridges. The proper estimation of loading exerted by the flow on the structure is important for design plans and is pertinent for evaluating its vulne...

A Distance Bounding Protocol for Location-Cloaked Applications.

PubMed

Molina-Martínez, Cristián; Galdames, Patricio; Duran-Faundez, Cristian

2018-04-26

Location-based services (LBSs) assume that users are willing to release trustworthy and useful details about their whereabouts. However, many location privacy concerns have arisen. For location privacy protection, several algorithms build a cloaking region to hide a user’s location. However, many applications may not operate adequately on cloaked locations. For example, a traditional distance bounding protocol (DBP)—which is run by two nodes called the prover and the verifier—may conclude an untight and useless distance between these two entities. An LBS (verifier) may use this distance as a metric of usefulness and trustworthiness of the location claimed by the user (prover). However, we show that if a tight distance is desired, traditional DBP can refine a user’s cloaked location and compromise its location privacy. To find a proper balance, we propose a location-privacy-aware DBP protocol. Our solution consists of adding some small delays before submitting any user’s response. We show that several issues arise when a certain delay is chosen, and we propose some solutions. The effectiveness of our techniques in balancing location refinement and utility is demonstrated through simulation.

Stochastic rainfall synthesis for urban applications using different regionalization methods

NASA Astrophysics Data System (ADS)

Callau Poduje, A. C.; Leimbach, S.; Haberlandt, U.

2017-12-01

The proper design and efficient operation of urban drainage systems require long and continuous rainfall series in a high temporal resolution. Unfortunately, these time series are usually available in a few locations and it is therefore suitable to develop a stochastic precipitation model to generate rainfall in locations without observations. The model presented is based on an alternating renewal process and involves an external and an internal structure. The members of these structures are described by probability distributions which are site specific. Different regionalization methods based on site descriptors are presented which are used for estimating the distributions for locations without observations. Regional frequency analysis, multiple linear regressions and a vine-copula method are applied for this purpose. An area located in the north-west of Germany is used to compare the different methods and involves a total of 81 stations with 5 min rainfall records. The site descriptors include information available for the whole region: position, topography and hydrometeorologic characteristics which are estimated from long term observations. The methods are compared directly by cross validation of different rainfall statistics. Given that the model is stochastic the evaluation is performed based on ensembles of many long synthetic time series which are compared with observed ones. The performance is as well indirectly evaluated by setting up a fictional urban hydrological system to test the capability of the different methods regarding flooding and overflow characteristics. The results show a good representation of the seasonal variability and good performance in reproducing the sample statistics of the rainfall characteristics. The copula based method shows to be the most robust of the three methods. Advantages and disadvantages of the different methods are presented and discussed.

CNV-CH: A Convex Hull Based Segmentation Approach to Detect Copy Number Variations (CNV) Using Next-Generation Sequencing Data

PubMed Central

De, Rajat K.

2015-01-01

Copy number variation (CNV) is a form of structural alteration in the mammalian DNA sequence, which are associated with many complex neurological diseases as well as cancer. The development of next generation sequencing (NGS) technology provides us a new dimension towards detection of genomic locations with copy number variations. Here we develop an algorithm for detecting CNVs, which is based on depth of coverage data generated by NGS technology. In this work, we have used a novel way to represent the read count data as a two dimensional geometrical point. A key aspect of detecting the regions with CNVs, is to devise a proper segmentation algorithm that will distinguish the genomic locations having a significant difference in read count data. We have designed a new segmentation approach in this context, using convex hull algorithm on the geometrical representation of read count data. To our knowledge, most algorithms have used a single distribution model of read count data, but here in our approach, we have considered the read count data to follow two different distribution models independently, which adds to the robustness of detection of CNVs. In addition, our algorithm calls CNVs based on the multiple sample analysis approach resulting in a low false discovery rate with high precision. PMID:26291322

CNV-CH: A Convex Hull Based Segmentation Approach to Detect Copy Number Variations (CNV) Using Next-Generation Sequencing Data.

PubMed

Sinha, Rituparna; Samaddar, Sandip; De, Rajat K

2015-01-01

Copy number variation (CNV) is a form of structural alteration in the mammalian DNA sequence, which are associated with many complex neurological diseases as well as cancer. The development of next generation sequencing (NGS) technology provides us a new dimension towards detection of genomic locations with copy number variations. Here we develop an algorithm for detecting CNVs, which is based on depth of coverage data generated by NGS technology. In this work, we have used a novel way to represent the read count data as a two dimensional geometrical point. A key aspect of detecting the regions with CNVs, is to devise a proper segmentation algorithm that will distinguish the genomic locations having a significant difference in read count data. We have designed a new segmentation approach in this context, using convex hull algorithm on the geometrical representation of read count data. To our knowledge, most algorithms have used a single distribution model of read count data, but here in our approach, we have considered the read count data to follow two different distribution models independently, which adds to the robustness of detection of CNVs. In addition, our algorithm calls CNVs based on the multiple sample analysis approach resulting in a low false discovery rate with high precision.

Assembly & Metrology of First Wall Components of SST-1

NASA Astrophysics Data System (ADS)

Parekh, Tejas; Santra, Prosenjit; Biswas, Prabal; Patel, Hiteshkumar; Paravastu, Yuvakiran; Jaiswal, Snehal; Chauhan, Pradeep; Babu, Gattu Ramesh; A, Arun Prakash; Bhavsar, Dhaval; Raval, Dilip C.; Khan, Ziauddin; Pradhan, Subrata

2017-04-01

First Wall Components (FWC) of SST-1 tokamak, which are in the immediate vicinity of plasma comprises of limiters, divertors, baffles, passive stabilizers are designed to operate long duration (1000 s) discharges of elongated plasma. All FWC consists of a copper alloy heat sink modules with SS cooling tubes brazed onto it, graphite tiles acting as armour material facing the plasma, and are mounted to the vacuum vessels with suitable Inconel support structures at ring & port locations. The FWC are very recently assembled and commissioned successfully inside the vacuum vessel of SST-1 undergoing a meticulous planning of assembly sequence, quality checks at every stage of the assembly process. This paper will present the metrology aspects & procedure of each FWC, both outside the vacuum vessel, and inside the vessel, assembly tolerances, tools, equipment and jig/fixtures, used at each stage of assembly, starting from location of support bases on vessel rings, fixing of copper modules on support structures, around 3800 graphite tile mounting on 136 copper modules with proper tightening torques, till final toroidal and poloidal geometry of the in-vessel components are obtained within acceptable limits, also ensuring electrical continuity of passive stabilizers to form a closed saddle loop, electrical isolation of passive stabilizers from vacuum vessel.

A testing machine for dental air-turbine handpiece characteristics: free-running speed, stall torque, bearing resistance.

PubMed

Darvell, Brain W; Dyson, J E

2005-01-01

The measurement of performance characteristics of dental air turbine handpieces is of interest with respect to product comparisons, standards specifications and monitoring of bearing longevity in clinical service. Previously, however, bulky and expensive laboratory equipment was required. A portable test machine is described for determining three key characteristics of dental air-turbine handpieces: free-running speed, stall torque and bearing resistance. It relies on a special circuit design for performing a hardware integration of a force signal with respect to rotational position, independent of the rate at which the turbine is allowed to turn during both stall torque and bearing resistance measurements. Free-running speed without the introduction of any imbalance can be readily monitored. From the essential linear relationship between torque and speed, dynamic torque and, hence, power, can then be calculated. In order for these measurements to be performed routinely with the necessary precision of location on the test stage, a detailed procedure for ensuring proper gripping of the handpiece is described. The machine may be used to verify performance claims, standard compliance checks should this be established as appropriate, monitor deterioration with time and usage in the clinical environment and for laboratory investigation of design development.

Fast massive preventive security and information communication systems

NASA Astrophysics Data System (ADS)

Akopian, David; Chen, Philip; Miryakar, Susheel; Kumar, Abhinav

2008-04-01

We present a fast massive information communication system for data collection from distributive sources such as cell phone users. As a very important application one can mention preventive notification systems when timely notification and evidence communication may help to improve safety and security through wide public involvement by ensuring easy-to-access and easy-to-communicate information systems. The technology significantly simplifies the response to the events and will help e.g. special agencies to gather crucial information in time and respond as quickly as possible. Cellular phones are nowadays affordable for most of the residents and became a common personal accessory. The paper describes several ways to design such systems including existing internet access capabilities of cell phones or downloadable specialized software. We provide examples of such designs. The main idea is in structuring information in predetermined way and communicating data through a centralized gate-server which will automatically process information and forward it to a proper destination. The gate-server eliminates a need in knowing contact data and specific local community infrastructure. All the cell phones will have self-localizing capability according to FCC E911 mandate, thus the communicated information can be further tagged automatically by location and time information.

Low-speed wind tunnel investigation of the static stability and control characteristics of an advanced turboprop configuration with the propellers placed over the tail. M.S. Thesis

NASA Technical Reports Server (NTRS)

Rhodes, Graham Scott

1990-01-01

An exploratory wind tunnel investigation was performed in the 30 x 60 foot wind tunnel to determine the low speed static stability and control characteristics into the deep stall regime of an advanced turboprop aircraft with the propellers located over the horizontal tail. By this arrangement, the horizontal tail could potentially provide acoustic shielding to reduce the high community noise caused by the propeller blades. The current configuration was a generic turboprop model equipped with 1 foot diameter single rotating eight bladed propellers that were designed for efficient cruise operation at a Mach number of 0.8. The data presented is static force data. The effects of power on the configuration characteristics were generally favorable. An arrangement with the propellers rotating with the outboard blades moving down was found to have significantly higher installed thrust than an arrangement with the propellers rotating with the inboard blades moving down. The primary unfavorable effect was a large pitch trim change which occurred with power, but the trim change could be minimized with a proper configuration design.

CFD Modeling of Launch Vehicle Aerodynamic Heating

NASA Technical Reports Server (NTRS)

Tashakkor, Scott B.; Canabal, Francisco; Mishtawy, Jason E.

2011-01-01

The Loci-CHEM 3.2 Computational Fluid Dynamics (CFD) code is being used to predict Ares-I launch vehicle aerodynamic heating. CFD has been used to predict both ascent and stage reentry environments and has been validated against wind tunnel tests and the Ares I-X developmental flight test. Most of the CFD predictions agreed with measurements. On regions where mismatches occurred, the CFD predictions tended to be higher than measured data. These higher predictions usually occurred in complex regions, where the CFD models (mainly turbulence) contain less accurate approximations. In some instances, the errors causing the over-predictions would cause locations downstream to be affected even though the physics were still being modeled properly by CHEM. This is easily seen when comparing to the 103-AH data. In the areas where predictions were low, higher grid resolution often brought the results closer to the data. Other disagreements are attributed to Ares I-X hardware not being present in the grid, as a result of computational resources limitations. The satisfactory predictions from CHEM provide confidence that future designs and predictions from the CFD code will provide an accurate approximation of the correct values for use in design and other applications

Drag-n-fly: a Proposal in Response to a Low Reynolds Number Station Keeping Mission

NASA Technical Reports Server (NTRS)

Foohey, Mark; Niehaus, John; Neumann, Jenny; Deviny, Pat; Zurovchak, Jerry; Brenner, Joey; Gendron, Peter

1990-01-01

The Drag-n-Fly is a remotely piloted, low Reynolds number vehicle. It was designed to maintain level controlled flight and fly a closed course at flight speeds corresponding to Reynolds numbers of less than 2 x 10(exp 5) and as close to 1 x 10(exp 5) as possible. The success of the mission will be associated with achieving the lowest mean chord Reynolds number possible and maximizing loiter time on the course. The flight plan for the Drag-n-Fly calls for the vehicle to ascent to a cruise altitude of 25 ft. The airfoil selected for the Drag-n-Fly is a Spica chosen for its high lift coefficient at low Reynolds number. The propulsion system for the Drag-n-Fly consists of a 10 inch diameter propeller mounted on the front of the vehicle. Structural support for the Drag-n-Fly comes from four box beams running the length of the fuselage. The tail and horizontal stabilizers are located far aft of the lifting surface in order to assure proper static stability. The present design for the Drag-n-Fly will meet the criteria for the present mission.

Reducing risks to children in vehicles with passenger airbags.

PubMed

Graham, J D; Goldie, S J; Segui-Gomez, M; Thompson, K M; Nelson, T; Glass, R; Simpson, A; Woerner, L G

1998-07-01

This review examines the risk that passenger airbags pose for children and discusses behavioral and technologic measures aimed at protecting children from airbag deployment. Although airbags reduce fatal crash injuries among adult drivers and passengers, this safety technology increases mortality risk among children younger than age 12. The magnitude of the risk is multiplied when children are unrestrained or restrained improperly. As new vehicles are resold to buyers who tend to be less safety-conscious than new car owners, the number of children endangered by passenger airbag deployment may increase. For vehicles already in the fleet, strong measures are required to secure children in the rear seat and increase the proper use of appropriate restraint systems through police enforcement of laws. One promising strategy is to amend child passenger safety laws to require that parents secure children in the rear seats. For future vehicles, a mandatory performance standard should be adopted that suppresses airbag deployment automatically if a child is located in the front passenger seat. Other promising improvements in airbag design also are discussed. Major changes in passenger airbag design must be evaluated in a broad analytical framework that considers the welfare of adults as well as children.

Fusing Horizons -- A Grammatical Design Approach for the Arts and Humanities: Using Rules, Contingency and Hermeneutics in Design Education

ERIC Educational Resources Information Center

Bruton, Dean

2007-01-01

This article argues that grammatical thinking within a framework of phenomenological hermeneutics assists designing and may properly be used as a fundamental teaching approach for an interdisciplinary art and design studio. Furthermore, it argues that the theme of grammatical design awareness could be considered as a generic issue across all…

A Course on Serious Game Design and Development Using an Online Problem-Based Learning Approach

ERIC Educational Resources Information Center

Kapralos, Bill; Fisher, Stephanie; Clarkson, Jessica; van Oostveen, Roland

2015-01-01

Purpose: The purpose of this paper is to describe a novel undergraduate course on serious game design and development that integrates both game and instructional design, thus providing an effective approach to teaching serious game design and development. Very little effort has been dedicated to the teaching of proper serious game design and…

Effect of low quality effluent from wastewater stabilization ponds to receiving bodies, case of Kilombero sugar ponds and Ruaha river, Tanzania.

PubMed

Machibya, Magayane; Mwanuzi, Fredrick

2006-06-01

A study was conducted in a sewage system at Kilombero Sugar Company to review its design, configuration, effectiveness and the quality of influent and effluent discharged into the Ruaha river (receiving body). The concern was that, the water in the river, after effluent has joined the river, is used as drinking water by villages located downstream of the river. Strategic sampling at the inlet of the oxidation pond, at the outlet and in the river before and after the effluent has joined the receiving body (river) was undertaken. Samples from each of these locations were taken three times, in the morning, noon and evening. The sample were then analysed in the laboratory using standard methods of water quality analysis. The results showed that the configuration and or the layout of the oxidation ponds (treatment plant) were not in accordance with the acceptable standards. Thus, the BOD5 of the effluent discharged into the receiving body (Ruaha River) was in the order of 41 mg/l and therefore not meeting several standards as set out both by Tanzanian and international water authorities. The Tanzanian water authorities, for example, requires that the BOD5 of the effluent discharged into receiving bodies be not more that 30 mg/l while the World Health Organization (WHO) requires that the effluent quality ranges between 10 - 30 mg/l. The paper concludes that proper design of treatment plants (oxidation ponds) is of outmost importance especially for factories, industries, camps etc located in rural developing countries where drinking water from receiving bodies like rivers and lakes is consumed without thorough treatment. The paper further pinpoint that both owners of treatment plants and water authorities should establish monitoring/management plan such that treatment plants (oxidation ponds) could be reviewed regarding the change on quantity of influent caused by population increase.

Texas flexible pavements and overlays : year 5 report - complete data documentation.

DOT National Transportation Integrated Search

2017-05-01

Proper calibration and validation of pavement design and performance models to Texas conditions is : essential for cost-effective flexible pavement design, performance predictions, and maintenance/rehab : strategies. The veracity of the calibration o...

Optimization of power and energy densities in supercapacitors

NASA Astrophysics Data System (ADS)

Robinson, David B.

Supercapacitors use nanoporous electrodes to store large amounts of charge on their high surface areas, and use the ions in electrolytes to carry charge into the pores. Their high power density makes them a potentially useful complement to batteries. However, ion transport through long, narrow channels still limits power and efficiency in these devices. Proper design can mitigate this. Current collector geometry must also be considered once this is done. Here, De Levie's model for porous electrodes is applied to quantitatively predict device performance and to propose optimal device designs for given specifications. Effects unique to nanoscale pores are considered, including that pores may not have enough salt to fully charge. Supercapacitors are of value for electric vehicles, portable electronics, and power conditioning in electrical grids with distributed renewable sources, and that value will increase as new device fabrication methods are developed and proper design accommodates those improvements. Example design outlines for vehicle applications are proposed and compared.

The Search for Extension: 7 Steps to Help People Find Research-Based Information on the Internet

ERIC Educational Resources Information Center

Hill, Paul; Rader, Heidi B.; Hino, Jeff

2012-01-01

For Extension's unbiased, research-based content to be found by people searching the Internet, it needs to be organized in a way conducive to the ranking criteria of a search engine. With proper web design and search engine optimization techniques, Extension's content can be found, recognized, and properly indexed by search engines and…

Effects of a Brief but Intensive Remedial Computer Intervention in a Sub-Sample of Kindergartners with Early Literacy Delays

ERIC Educational Resources Information Center

Van der Kooy-Hofland, Verna A. C.; Bus, Adriana G.; Roskos, Kathleen

2012-01-01

Living Letters is an adaptive game designed to promote children's combining of how the proper name sounds with their knowledge of how the name looks. A randomized controlled trial (RCT) was used to experimentally test whether priming for attending to the sound-symbol relationship in the proper name can reduce the risk for developing reading…

On the origin of the Monoceros Ring - I. Kinematics, proper motions, and the nature of the progenitor

NASA Astrophysics Data System (ADS)

Guglielmo, Magda; Lane, Richard R.; Conn, Blair C.; Ho, Anna Y. Q.; Ibata, Rodrigo A.; Lewis, Geraint F.

2018-03-01

The Monoceros Ring (MRi) structure is an apparent stellar overdensity that has been postulated to entirely encircle the Galactic plane and has been variously described as being due to line-of-sight effects of the Galactic warp and flare or of extragalactic origin (via accretion). Despite being intensely scrutinized in the literature for more than a decade, no studies to date have been able to definitively uncover its origins. Here we use N-body simulations and a genetic algorithm to explore the parameter space for the initial position, orbital parameters, and, for the first time, the final location of a satellite progenitor. We fit our models to the latest Pan-STARRS data to determine whether an accretion scenario is capable of producing an in-plane ring-like structure matching the known parameters of the MRi. Our simulations produce streams that closely match the location, proper motion, and kinematics of the MRi structure. However, we are not able to reproduce the mass estimates from earlier studies based on Pan-STARRS data. Furthermore, in contrast to earlier studies, our best-fitting models are those for progenitors on retrograde orbits. If the MRi was produced by satellite accretion, we find that its progenitor has an initial mass upper limit of ˜1010 M⊙ and the remnant is likely located behind the Galactic bulge, making it difficult to locate observationally. While our models produce realistic MRi-like structures, we cannot definitively conclude that the MRi was produced by the accretion of a satellite galaxy.

Prehepatocholedochal proper hepatic artery. Rare anatomical variant. Surgical considerations. Case report.

PubMed

Ardeleanu, V; Chicoş, S; Tutunaru, D; Georgescu, C

2014-01-01

In classical anatomic variants, the proper hepatic artery (PHA)continues the common hepatic artery (CHA) after the gastroduodenal artery (GDA) detaches itself and divides into the right hepatic artery (RHA) and left hepatic artery (LHA), the proper hepatic artery being located to the left of the hepatocholedochal duct (HCD). This paper presents an abnormal positioning of the PHA placed before the HCD with an increased diameter of about 5-7 mm, which could be confused with the HCD. We present the case of a 57 year-old woman diagnosed with acute lithiasic cholecystitis, associated with hypersplenism and hypertension. The literature mentions manifold anatomical variants of arterial liver vascularization,including PHA. For this reason, this paper presents an overview of similar cases that can be found in medical literature. The aforementioned case is a rare topographic anatomy for the PHA that can easily pass for HCD especially during celioscopy, therefore it is crucial for this to be acknowledged by all surgeons. Celsius.

A DYNAMICAL SIGNATURE OF MULTIPLE STELLAR POPULATIONS IN 47 TUCANAE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richer, Harvey B.; Heyl, Jeremy; Anderson, Jay

2013-07-01

Based on the width of its main sequence, and an actual observed split when viewed through particular filters, it is widely accepted that 47 Tucanae contains multiple stellar populations. In this contribution, we divide the main sequence of 47 Tuc into four color groups, which presumably represent stars of various chemical compositions. The kinematic properties of each of these groups are explored via proper motions, and a strong signal emerges of differing proper-motion anisotropies with differing main-sequence color; the bluest main-sequence stars exhibit the largest proper-motion anisotropy which becomes undetectable for the reddest stars. In addition, the bluest stars aremore » also the most centrally concentrated. A similar analysis for Small Magellanic Cloud stars, which are located in the background of 47 Tuc on our frames, yields none of the anisotropy exhibited by the 47 Tuc stars. We discuss implications of these results for possible formation scenarios of the various populations.« less

Analysis and optimization of Love wave liquid sensors.

PubMed

Jakoby, B; Vellekoop, M J

1998-01-01

Love wave sensors are highly sensitive microacoustic devices, which are well suited for liquid sensing applications thanks to the shear polarization of the wave. The sensing mechanism thereby relies on the mechanical (or acoustic) interaction of the device with the liquid. The successful utilization of Love wave devices for this purpose requires proper shielding to avoid unwanted electric interaction of the liquid with the wave and the transducers. In this work we describe the effects of this electric interaction and the proper design of a shield to prevent it. We present analysis methods, which illustrate the impact of the interaction and which help to obtain an optimized design of the proposed shield. We also present experimental results for devices that have been fabricated according to these design rules.

Project Management Approaches for Online Learning Design

ERIC Educational Resources Information Center

Eby, Gulsun; Yuzer, T. Volkan

2013-01-01

Developments in online learning and its design are areas that continue to grow in order to enhance students' learning environments and experiences. However, in the implementation of new technologies, the importance of properly and fairly overseeing these courses is often undervalued. "Project Management Approaches for Online Learning Design"…

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2013 CFR

2013-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2011 CFR

2011-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2014 CFR

2014-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2012 CFR

2012-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

29 CFR 1926.703 - Requirements for cast-in-place concrete.

Code of Federal Regulations, 2010 CFR

2010-07-01

... members have been designed for such loading. (8) Whenever single post shores are used one on top of... been properly tested with an appropriate ASTM standard test method designed to indicate the concrete...) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be...

Design, construction, and evaluation of a 1:8 scale model binaural manikin.

PubMed

Robinson, Philip; Xiang, Ning

2013-03-01

Many experiments in architectural acoustics require presenting listeners with simulations of different rooms to compare. Acoustic scale modeling is a feasible means to create accurate simulations of many rooms at reasonable cost. A critical component in a scale model room simulation is a receiver that properly emulates a human receiver. For this purpose, a scale model artificial head has been constructed and tested. This paper presents the design and construction methods used, proper equalization procedures, and measurements of its response. A headphone listening experiment examining sound externalization with various reflection conditions is presented that demonstrates its use for psycho-acoustic testing.

Balancing Play, Meaning and Reality: The Design Philosophy of LEVEE PATROLLER

ERIC Educational Resources Information Center

Harteveld, Casper; Guimaraes, Rui; Mayer, Igor S.; Bidarra, Rafael

2010-01-01

Most serious games have been developed without a proper and comprehensive design theory. To contribute to the development of such a theory, this article presents the underlying design philosophy of LEVEE PATROLLER, a game to train levee patrollers in the Netherlands. This philosophy stipulates that the design of a digital serious game is a…

Analysis of the configuration and the location of thermographic equipment for the inspection in photovoltaic systems

NASA Astrophysics Data System (ADS)

Álvarez-Tey, G.; Jiménez-Castañeda, R.; Carpio, J.

2017-12-01

The infrared (IR) thermography is a non-destructive technique (NDT) which is used to carry out maintenance quickly and easily in photovoltaic (PV) systems. IR imaging with thermographic cameras under steady state conditions is a usual method for quality control of PV modules and plants in operation. For the proper IR inspection which determines the severity or the importance of the detected findings, it is necessary to consider different aspects of the configuration and the location of the thermographic equipment which allow reducing measuring errors. This paper considers some elements which contribute to the accurate configuration of the thermographic equipment. The influence of the reflected apparent temperature in outdoor IR inspections is analysed and it is proposed a simple method for obtaining it. Besides, the importance of the emissivity in IR thermography is analysed. For that, the value of the emissivity in PV modules of various types both front and rear shape is determined experimentally. It is also studied the proper location of the thermographic equipment in order to minimize reflections of the sun and the sky. For this objective, it is studied the ideal and minimum height of inspection according to the layout of the PV system. In a particular case, it is also analysed the influence of the horizontal angle of thermographic inspection and the reflected radiation.

Assessing groundwater quality for irrigation using indicator kriging method

NASA Astrophysics Data System (ADS)

Delbari, Masoomeh; Amiri, Meysam; Motlagh, Masoud Bahraini

2016-11-01

One of the key parameters influencing sprinkler irrigation performance is water quality. In this study, the spatial variability of groundwater quality parameters (EC, SAR, Na+, Cl-, HCO3 - and pH) was investigated by geostatistical methods and the most suitable areas for implementation of sprinkler irrigation systems in terms of water quality are determined. The study was performed in Fasa county of Fars province using 91 water samples. Results indicated that all parameters are moderately to strongly spatially correlated over the study area. The spatial distribution of pH and HCO3 - was mapped using ordinary kriging. The probability of concentrations of EC, SAR, Na+ and Cl- exceeding a threshold limit in groundwater was obtained using indicator kriging (IK). The experimental indicator semivariograms were often fitted well by a spherical model for SAR, EC, Na+ and Cl-. For HCO3 - and pH, an exponential model was fitted to the experimental semivariograms. Probability maps showed that the risk of EC, SAR, Na+ and Cl- exceeding the given critical threshold is higher in lower half of the study area. The most proper agricultural lands for sprinkler irrigation implementation were identified by evaluating all probability maps. The suitable areas for sprinkler irrigation design were determined to be 25,240 hectares, which is about 34 percent of total agricultural lands and are located in northern and eastern parts. Overall the results of this study showed that IK is an appropriate approach for risk assessment of groundwater pollution, which is useful for a proper groundwater resources management.

A dynamic model for generating actuator specifications for small arms barrel active stabilization

NASA Astrophysics Data System (ADS)

Pathak, Anupam; Brei, Diann; Luntz, Jonathan; Lavigna, Chris

2006-03-01

Due to stresses encountered in combat, it is known that soldier marksmanship noticeably decreases regardless of prior training. Active stabilization systems in small arms have potential to address this problem to increase soldier survivability and mission effectiveness. The key to success is proper actuator design, but this is highly dependent on proper specification which is challenging due to the human/weapon interaction. This paper presents a generic analytical dynamic model which is capable of defining the necessary actuation specifications for a wide range of small arms platforms. The model is unique because it captures the human interface--shoulder and arm--that introduces the jitter disturbance in addition to the geometry, inertial properties and active stabilization stiffness of the small arms platform. Because no data to date is available for actual shooter-induced disturbance in field conditions, a method is given using the model to back-solve from measured shooting range variability data the disturbance amplitude information relative to the input source (arm or shoulder). As examples of the applicability of the model to various small arms systems, two different weapon systems were investigated: the M24 sniper weapon and the M16 assault rifle. In both cases, model based simulations provided valuable insight into impact on the actuation specifications (force, displacement, phase, frequency) due to the interplay of the human-weapon-active stabilization interface including the effect of shooter-disturbance frequency, disturbance location (shoulder vs. arm), and system parameters (stiffness, barrel rotation).

Control of Smart Building Using Advanced SCADA

NASA Astrophysics Data System (ADS)

Samuel, Vivin Thomas

For complete control of the building, a proper SCADA implementation and the optimization strategy has to be build. For better communication and efficiency a proper channel between the Communication protocol and SCADA has to be designed. This paper concentrate mainly between the communication protocol, and the SCADA implementation, for a better optimization and energy savings is derived to large scale industrial buildings. The communication channel used in order to completely control the building remotely from a distant place. For an efficient result we consider the temperature values and the power ratings of the equipment so that while controlling the equipment, we are setting a threshold values for FDD technique implementation. Building management system became a vital source for any building to maintain it and for safety purpose. Smart buildings, refers to various distinct features, where the complete automation system, office building controls, data center controls. ELC's are used to communicate the load values of the building to the remote server from a far location with the help of an Ethernet communication channel. Based on the demand fluctuation and the peak voltage, the loads operate differently increasing the consumption rate thus results in the increase in the annual consumption bill. In modern days, saving energy and reducing the consumption bill is most essential for any building for a better and long operation. The equipment - monitored regularly and optimization strategy is implemented for cost reduction automation system. Thus results in the reduction of annual cost reduction and load lifetime increase.

Outer rotation curve of the Galaxy with VERA. III. Astrometry of IRAS 07427-2400 and test of the density-wave theory

NASA Astrophysics Data System (ADS)

Sakai, Nobuyuki; Nakanishi, Hiroyuki; Matsuo, Mitsuhiro; Koide, Nagito; Tezuka, Daisuke; Kurayama, Tomoharu; Shibata, Katsunori M.; Ueno, Yuji; Honma, Mareki

2015-08-01

We report the trigonometric parallax of IRAS 07427-2400 with VERA to be 0.185 ± 0.027 mas, corresponding to a distance of 5.41^{+0.92}_{-0.69}kpc. The result is consistent with the previous result of 5.32^{+0.49}_{-0.42}kpc obtained by Choi et al. (2014, ApJ, 790, 99) within error. To remove the effect of internal maser motions (e.g., random motions), we observed six maser features associated with IRAS 07427-2400 and determined systematic proper motions of the source by averaging proper motions of the six maser features. The obtained proper motions are (μαcos δ, μδ) = (-1.79 ± 0.32, 2.60 ± 0.17) mas yr-1 in equatorial coordinates, while Choi et al. (2014) showed (μαcos δ, μδ) = (-2.43 ± 0.02, 2.49 ± 0.09) mas yr-1 with one maser feature. Our astrometry results place the source in the Perseus arm, the nearest main arm in the Milky Way. Using our result with previous astrometry results obtained from observations of the Perseus arm, we conducted direct (quantitative) comparisons between 27 astrometry results and an analytic gas dynamics model based on the density-wave theory, obtaining two results. First is the pitch angle of the Perseus arm determined by VLBI astrometry, 11.1° ± 1.4°, differing from what is determined by the spiral potential model (probably traced by stars), ˜ 20°. The second is an offset between a dense gas region and the bottom of the spiral potential model. The dense gas region traced by VLBI astrometry is located downstream of the spiral potential model, which was previously confirmed in the nearby grand-design spiral galaxy M 51 in Egusa, Koda, and Scoville (2011, ApJ, 726, 85).

Guidelines for Developing Spacecraft Structural Requirements: A Thermal and Environmental Perspective

NASA Technical Reports Server (NTRS)

Holladay, Jon; Day, Greg; Gill, Larry

2004-01-01

Spacecraft are typically designed with a primary focus on weight in order to meet launch vehicle performance parameters. However, for pressurized and/or man-rated spacecraft, it is also necessary to have an understanding of the vehicle operating environments to properly size the pressure vessel. Proper sizing of the pressure vessel requires an understanding of the space vehicle's life cycle and compares the physical design optimization (weight and launch "cost") to downstream operational complexity and total life cycle cost. This paper will provide an overview of some major environmental design drivers and provide examples for calculating the optimal design pressure versus a selected set of design parameters related to thermal and environmental perspectives. In addition, this paper will provide a generic set of cracking pressures for both positive and negative pressure relief valves that encompasses worst case environmental effects for a variety of launch / landing sites. Finally, several examples are included to highlight pressure relief set points and vehicle weight impacts for a selected set of orbital missions.

Years to first rehabilitation of superpave hot mix asphalt.

DOT National Transportation Integrated Search

2014-07-01

The Colorado Department of Transportation (CDOT) spends more than 30 percent of its annual construction and : maintenance budget on pavements, so pavements need to be properly designed using an analytical process with : accurate design inputs. A pave...

The Importance of Semi-Major Axis Knowledge in the Determination of Near-Circular Orbits

NASA Technical Reports Server (NTRS)

Carpenter, J. Russell; Schiesser, Emil R.

1998-01-01

Modem orbit determination has mostly been accomplished using Cartesian coordinates. This usage has carried over in recent years to the use of GPS for satellite orbit determination. The unprecedented positioning accuracy of GPS has tended to focus attention more on the system's capability to locate the spacecraft's location at a particular epoch than on its accuracy in determination of the orbit, per se. As is well-known, the latter depends on a coordinated knowledge of position, velocity, and the correlation between their errors. Failure to determine a properly coordinated position/velocity state vector at a given epoch can lead to an epoch state that does not propagate well, and/or may not be usable for the execution of orbit adjustment maneuvers. For the quite common case of near-circular orbits, the degree to which position and velocity estimates are properly coordinated is largely captured by the error in semi-major axis (SMA) they jointly produce. Figure 1 depicts the relationships among radius error, speed error, and their correlation which exist for a typical low altitude Earth orbit. Two familiar consequences are the relationship Figure 1 shows are the following: (1) downrange position error grows at the per orbit rate of 3(pi) times the SMA error; (2) a velocity change imparted to the orbit will have an error of (pi) divided by the orbit period times the SMA error. A less familiar consequence occurs in the problem of initializing the covariance matrix for a sequential orbit determination filter. An initial covariance consistent with orbital dynamics should be used if the covariance is to propagate well. Properly accounting for the SMA error of the initial state in the construction of the initial covariance accomplishes half of this objective, by specifying the partition of the covariance corresponding to down-track position and radial velocity errors. The remainder of the in-plane covariance partition may be specified in terms of the flight path angle error of the initial state. Figure 2 illustrates the effect of properly and not properly initializing a covariance. This figure was produced by propagating the covariance shown on the plot, without process noise, in a circular low Earth orbit whose period is 5828.5 seconds. The upper subplot, in which the proper relationships among position, velocity, and their correlation has been used, shows overall error growth, in terms of the standard deviations of the inertial position coordinates, of about half of the lower subplot, whose initial covariance was based on other considerations.

The cost risk implementation on design-build project of integrated public spaces child friendly in capital of Jakarta

NASA Astrophysics Data System (ADS)

Mardiaman, Mubarok, Abdul

2017-11-01

Jakarta area of 662.33 km2 with a population of 10,075,030 inhabitants and green open spaces 9.98%. The Jakarta government built a child-friendly integrated open space as facilities for playing. Providing of facilities was hoped suitable with time, cost, quality, accountability and proper financial governance. Based on the PU ministerial regulation number 19/PRT/M/2015 on the standards and guidelines for procurement the design and construction work on the integrated build and the PU ministerial regulation No. 07/PRT/M/2011 on standards and guidelines for procurement of construction works and consulting services of public works and the ministry of housing. RPTRA development at 123 locations in Jakarta was implemented base on the contract of design and build. The design study was influenced by the cost elements; the main strength (expert), skilled personnel, support personnel, major equipment and support. The construction fee relies on; expert implementation, hardware implementation, preparation work, land, buildings, courtyards, fences, complementary and governance capabilities for human resources in completing the construction activities to minimize the cost risk. Montecarlo simulations was conducted to determine the average unit price, model and analyze systems. In the cost contract, the percentage of design work stipulated 2.5%, build 97.5%. Base on regulation the minister of public work for design work cost 2.72%, build 97.28%. Then, actual cost for design 2.67% and build 97.33%. From the three reference was shown that there are differentiation one another. The acceleration of planning able to make the cost and time more efficient that impact on the implementation margin.

Design of a video teleconference facility for a synchronous satellite communications link

NASA Technical Reports Server (NTRS)

Richardson, M. D.

1979-01-01

The system requirements, design tradeoffs, and final design of a video teleconference facility are discussed, including proper lighting, graphics transmission, and picture aesthetics. Methods currently accepted in the television broadcast industry are used in the design. The unique problems associated with using an audio channel with a synchronous satellite communications link are discussed, and a final audio system design is presented.

Control of Arabidopsis leaf morphogenesis through regulation of the YABBY and KNOX families of transcription factors

USDA-ARS?s Scientific Manuscript database

The patterning of initiating organs along specific axes of polarity is critical for the proper development of all higher organisms. Plant lateral organs, such as leaves, are derived from the shoot apical meristems located at the growing tips. After initiation, the leaf primordia of species such as A...

26 CFR 1.103(n)-6T - Determinations of population (temporary).

Code of Federal Regulations, 2011 CFR

2011-04-01

...(n)-6T Section 1.103(n)-6T Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY....103(n)-6T Determinations of population (temporary). Q-1: What is the proper method for determining...(n)-6T: Example. County Q is located within State R. There are no constitutional home rule cities in...

Simba: Coming of Age for the African-American Male.

ERIC Educational Resources Information Center

Hill, Paul, Jr.

Black American males lack a ceremony to usher them into manhood. Such a ritual could help to ensure proper socialization and self identity. It may counteract the negative influence of street culture. Like other major life change ceremonies, a coming-of-age rite can help to locate anew the individual within the community. Elements of this rite of…

Applications of Bayesian spectrum representation in acoustics

NASA Astrophysics Data System (ADS)

Botts, Jonathan M.

This dissertation utilizes a Bayesian inference framework to enhance the solution of inverse problems where the forward model maps to acoustic spectra. A Bayesian solution to filter design inverts a acoustic spectra to pole-zero locations of a discrete-time filter model. Spatial sound field analysis with a spherical microphone array is a data analysis problem that requires inversion of spatio-temporal spectra to directions of arrival. As with many inverse problems, a probabilistic analysis results in richer solutions than can be achieved with ad-hoc methods. In the filter design problem, the Bayesian inversion results in globally optimal coefficient estimates as well as an estimate the most concise filter capable of representing the given spectrum, within a single framework. This approach is demonstrated on synthetic spectra, head-related transfer function spectra, and measured acoustic reflection spectra. The Bayesian model-based analysis of spatial room impulse responses is presented as an analogous problem with equally rich solution. The model selection mechanism provides an estimate of the number of arrivals, which is necessary to properly infer the directions of simultaneous arrivals. Although, spectrum inversion problems are fairly ubiquitous, the scope of this dissertation has been limited to these two and derivative problems. The Bayesian approach to filter design is demonstrated on an artificial spectrum to illustrate the model comparison mechanism and then on measured head-related transfer functions to show the potential range of application. Coupled with sampling methods, the Bayesian approach is shown to outperform least-squares filter design methods commonly used in commercial software, confirming the need for a global search of the parameter space. The resulting designs are shown to be comparable to those that result from global optimization methods, but the Bayesian approach has the added advantage of a filter length estimate within the same unified framework. The application to reflection data is useful for representing frequency-dependent impedance boundaries in finite difference acoustic simulations. Furthermore, since the filter transfer function is a parametric model, it can be modified to incorporate arbitrary frequency weighting and account for the band-limited nature of measured reflection spectra. Finally, the model is modified to compensate for dispersive error in the finite difference simulation, from the filter design process. Stemming from the filter boundary problem, the implementation of pressure sources in finite difference simulation is addressed in order to assure that schemes properly converge. A class of parameterized source functions is proposed and shown to offer straightforward control of residual error in the simulation. Guided by the notion that the solution to be approximated affects the approximation error, sources are designed which reduce residual dispersive error to the size of round-off errors. The early part of a room impulse response can be characterized by a series of isolated plane waves. Measured with an array of microphones, plane waves map to a directional response of the array or spatial intensity map. Probabilistic inversion of this response results in estimates of the number and directions of image source arrivals. The model-based inversion is shown to avoid ambiguities associated with peak-finding or inspection of the spatial intensity map. For this problem, determining the number of arrivals in a given frame is critical for properly inferring the state of the sound field. This analysis is effectively compression of the spatial room response, which is useful for analysis or encoding of the spatial sound field. Parametric, model-based formulations of these problems enhance the solution in all cases, and a Bayesian interpretation provides a principled approach to model comparison and parameter estimation. v

State-Of High Brightness RF Photo-Injector Design

NASA Astrophysics Data System (ADS)

Ferrario, Massimo; Clendenin, Jym; Palmer, Dennis; Rosenzweig, James; Serafini, Luca

2000-04-01

The art of designing optimized high brightness electron RF Photo-Injectors has moved in the last decade from a cut and try procedure, guided by experimental experience and time consuming particle tracking simulations, up to a fast parameter space scanning, guided by recent analytical results and a fast running semi-analytical code, so to reach the optimum operating point which corresponds to maximum beam brightness. Scaling laws and the theory of invariant envelope provide to the designers excellent tools for a first parameters choice and the code HOMDYN, based on a multi-slice envelope description of the beam dynamics, is tailored to describe the space charge dominated dynamics of laminar beams in presence of time dependent space charge forces, giving rise to a very fast modeling capability for photo-injectors design. We report in this talk the results of a recent beam dynamics study, motivated by the need to redesign the LCLS photoinjector. During this work a new effective working point for a split RF photoinjector has been discovered by means of the previous mentioned approach. By a proper choice of rf gun and solenoid parameters, the emittance evolution shows a double minimum behavior in the drifting region. If the booster is located where the relative emittance maximum and the envelope waist occur, the second emittance minimum can be shifted at the booster exit and frozen at a very low level (0.3 mm-mrad for a 1 nC flat top bunch), to the extent that the invariant envelope matching conditions are satisfied.

Next Generation NASA Initiative for Space Geodesy

NASA Technical Reports Server (NTRS)

Merkowitz, S. M.; Desai, S.; Gross, R. S.; Hilliard, L.; Lemoine, F. G.; Long, J. L.; Ma, C.; McGarry J. F.; Murphy, D.; Noll, C. E.;

Effect of Doppler flow meter position on discharge measurement in surcharged manholes.

PubMed

Yang, Haoming; Zhu, David Z; Liu, Yanchen

2018-02-01

Determining the proper installation location of flow meters is important for accurate measurement of discharge in sewer systems. In this study, flow field and flow regimes in two types of manholes under surcharged flow were investigated using a commercial computational fluid dynamics (CFD) code. The error in measuring the flow discharge using a Doppler flow meter (based on the velocity in a Doppler beam) was then estimated. The values of the corrective coefficient were obtained for the Doppler flow meter at different locations under various conditions. Suggestions for selecting installation positions are provided.

Propagation of the velocity model uncertainties to the seismic event location

NASA Astrophysics Data System (ADS)

Gesret, A.; Desassis, N.; Noble, M.; Romary, T.; Maisons, C.

2015-01-01

Earthquake hypocentre locations are crucial in many domains of application (academic and industrial) as seismic event location maps are commonly used to delineate faults or fractures. The interpretation of these maps depends on location accuracy and on the reliability of the associated uncertainties. The largest contribution to location and uncertainty errors is due to the fact that the velocity model errors are usually not correctly taken into account. We propose a new Bayesian formulation that integrates properly the knowledge on the velocity model into the formulation of the probabilistic earthquake location. In this work, the velocity model uncertainties are first estimated with a Bayesian tomography of active shot data. We implement a sampling Monte Carlo type algorithm to generate velocity models distributed according to the posterior distribution. In a second step, we propagate the velocity model uncertainties to the seismic event location in a probabilistic framework. This enables to obtain more reliable hypocentre locations as well as their associated uncertainties accounting for picking and velocity model uncertainties. We illustrate the tomography results and the gain in accuracy of earthquake location for two synthetic examples and one real data case study in the context of induced microseismicity.

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

Collection of materials and performance data for Texas flexible pavements and overlays : project summary.

DOT National Transportation Integrated Search

2015-08-31

Proper calibration of mechanistic-empirical : (M-E) design and rehabilitation performance : models to meet Texas conditions is essential : for cost-effective flexible pavement designs. : Such a calibration effort would require a : reliable source of ...

46 CFR 61.35-1 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PERIODIC TESTS AND INSPECTIONS Design Verification and Periodic Testing for Automatic Auxiliary Boilers § 61.35-1 General. (a) All automatic... equipment must be tested and inspected to verify their proper design, construction, installation, and...

Designing Birefringent Filters For Solid-State Lasers

NASA Technical Reports Server (NTRS)

Monosmith, Bryan

1992-01-01

Mathematical model enables design of filter assembly of birefringent plates as integral part of resonator cavity of tunable solid-state laser. Proper design treats polarization eigenstate of entire resonator as function of wavelength. Program includes software modules for variety of optical elements including Pockels cell, laser rod, quarter- and half-wave plates, Faraday rotator, and polarizers.

Statistical Analysis for the Solomon Four-Group Design. Research Report 99-06.

ERIC Educational Resources Information Center

van Engelenburg, Gijsbert

The Solomon four-group design (R. Solomon, 1949) is a very useful experimental design to investigate the main effect of a pretest and the interaction of pretest and treatment. Although the design was proposed half a century ago, no proper data analysis techniques have been available. This paper describes how data from the Solomon four-group design…

Inter-Creative Course Model Proposal: Teaching- Learning Design in Secondary Schools of TRNC

ERIC Educational Resources Information Center

Ulas-Dagli, Ugur; Pasaoglulari-Sahin, Nil; Güley, Kamil

2013-01-01

Problem Statement: Design is an indispensable part of the human being. It enters one's life on the very first day that the eyes open. Design awareness is developed at an early age. With a proper education, even in the preschool years, design is experienced within one's close environment. Purpose of the Study: This study aims to determine the…

A Common Proper Motion Stellar Companion to HAT-P-7

NASA Technical Reports Server (NTRS)

Grady, Carol A.; McElwain, Michael W.; Narita, Norio; Takahashi, Yasuhiro H.; Kuzuhara, Masayuki; Hirano, Teruyuki; Suenaga, Takuya

2012-01-01

We report that HAT-P-7 has a common proper motion stellar companion. The companion is located at approx. 3.9 arcsec to the east and estimated as an M5.5V dwarf based on its colors. We also confirm the presence of the third companion, which was first reported by Winn et al. (2009), based on long-term radial velocity measurements. We revisit the migration mechanism of HAT-P-7b given the presence of those companions, and propose sequential Kozai migration as a likely scenario in this system. This scenario may explain the reason for an outlier in the discussion of the spin-orbit alignment timescale for HAT-P-7b by Albrecht et al. (2012).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Chemical Hazard Response Information System (CHRIS) is designed to provide timely information essential for proper decision-making by responsible Coast Guard personnel and others during emergencies involving the water transport of hazardous chemicals. A secondary purpose is the provision of certain basic non-emergency-related information to support the Coast Guard in its efforts to achieve improved levels of safety in the bulk shipment of hazardous chemicals. CHRIS consists of four reference guides or manuals, a regional contingency plan, a hazard-assessment computer system (HACS), and an organizational entity located at Coast Guard headquarters. The four manuals contain chemical data, hazard-assessment methods, andmore » response guides. Regional data for the entire coastline are included in the Coastal Regional Contingency Plans. The headquarters staff operates the hazard-assessment computer system and provides technical assistance on request by field personnel during emergencies. In addition, it is responsible for periodic update and maintenance of CHRIS. A brief description of each component of CHRIS and its relation to this manual - the Hazard-Assessment Handbook - is provided.« less

Robust Indoor Human Activity Recognition Using Wireless Signals.

PubMed

Wang, Yi; Jiang, Xinli; Cao, Rongyu; Wang, Xiyang

2015-07-15

Wireless signals-based activity detection and recognition technology may be complementary to the existing vision-based methods, especially under the circumstance of occlusions, viewpoint change, complex background, lighting condition change, and so on. This paper explores the properties of the channel state information (CSI) of Wi-Fi signals, and presents a robust indoor daily human activity recognition framework with only one pair of transmission points (TP) and access points (AP). First of all, some indoor human actions are selected as primitive actions forming a training set. Then, an online filtering method is designed to make actions' CSI curves smooth and allow them to contain enough pattern information. Each primitive action pattern can be segmented from the outliers of its multi-input multi-output (MIMO) signals by a proposed segmentation method. Lastly, in online activities recognition, by selecting proper features and Support Vector Machine (SVM) based multi-classification, activities constituted by primitive actions can be recognized insensitive to the locations, orientations, and speeds.

Heuristic automation for decluttering tactical displays.

PubMed

St John, Mark; Smallman, Harvey S; Manes, Daniel I; Feher, Bela A; Morrison, Jeffrey G

2005-01-01

Tactical displays can quickly become cluttered with large numbers of symbols that can compromise effective monitoring. Here, we studied how heuristic automation can aid users by intelligently "decluttering" the display. In a realistic simulated naval air defense task, 27 experienced U.S. Navy users monitored a cluttered airspace and executed defensive responses against significant threats. An algorithm continuously evaluated aircraft for their levels of threat and decluttered the less threatening ones by dimming their symbols. Users appropriately distrusted and spot-checked the automation's assessments, and decluttering had very little effect on which aircraft were judged as significantly threatening. Nonetheless, decluttering improved the timeliness of responses to threatening aircraft by 25% as compared with a baseline display with no decluttering; it was especially beneficial for threats in more peripheral locations, and 25 of 27 participants preferred decluttering. Heuristic automation, when properly designed to guide users' attention by decluttering less important objects, may prove valuable in many cluttered monitoring situations, including air traffic management, crisis team management, and tactical situation awareness in general.

Integrated Hydrogeological Investigation on the Vulnerability of a Pumping Station at a Losing Stream

NASA Astrophysics Data System (ADS)

Ngueleu Kamangou, Stephane; Vogt, Tobias; Cirpka, Olaf

2010-05-01

River restoration usually includes alteration of the river channel morphology. Thereby the interaction between river and groundwater can be modified. For the design of a river restoration project - especially in the vicinity of a groundwater pumping well for drinking water production - this impact must be predicted. But a good prediction requires a proper understanding of the existing situation. Numerical models help to improve the strategy of a successful river restoration project. The main objective of this study was to investigate the vulnerability of a pumping station located at losing river in northeast Switzerland. Besides the effect that river restoration could create, a particular attention was placed on the effect of a beaver dam in a side channel close to the pumping station. Analysis of field measurements coupled with numerical modeling of the pumping station area improved the understanding of the interactions in the river corridor between the river, side channels and the alluvial aquifer.

Threatening communication: a critical re-analysis and a revised meta-analytic test of fear appeal theory.

PubMed

Peters, Gjalt-Jorn Ygram; Ruiter, Robert A C; Kok, Gerjo

2013-05-01

Despite decades of research, consensus regarding the dynamics of fear appeals remains elusive. A meta-analysis was conducted that was designed to resolve this controversy. Publications that were included in previous meta-analyses were re-analysed, and a number of additional publications were located. The inclusion criteria were full factorial orthogonal manipulations of threat and efficacy, and measurement of behaviour as an outcome. Fixed and random effects models were used to compute mean effect size estimates. Meta-analysis of the six studies that satisfied the inclusion criteria clearly showed a significant interaction between threat and efficacy, such that threat only had an effect under high efficacy (d = 0.31), and efficacy only had an effect under high threat (d = 0.71). Inconsistency in results regarding the effectiveness of threatening communication can likely be attributed to flawed methodology. Proper tests of fear appeal theory yielded the theoretically hypothesised interaction effect. Threatening communication should exclusively be used when pilot studies indicate that an intervention successfully enhances efficacy.

Geolocation and Pointing Accuracy Analysis for the WindSat Sensor

NASA Technical Reports Server (NTRS)

Meissner, Thomas; Wentz, Frank J.; Purdy, William E.; Gaiser, Peter W.; Poe, Gene; Uliana, Enzo A.

2006-01-01

Geolocation and pointing accuracy analyses of the WindSat flight data are presented. The two topics were intertwined in the flight data analysis and will be addressed together. WindSat has no unusual geolocation requirements relative to other sensors, but its beam pointing knowledge accuracy is especially critical to support accurate polarimetric radiometry. Pointing accuracy was improved and verified using geolocation analysis in conjunction with scan bias analysis. nvo methods were needed to properly identify and differentiate between data time tagging and pointing knowledge errors. Matchups comparing coastlines indicated in imagery data with their known geographic locations were used to identify geolocation errors. These coastline matchups showed possible pointing errors with ambiguities as to the true source of the errors. Scan bias analysis of U, the third Stokes parameter, and of vertical and horizontal polarizations provided measurement of pointing offsets resolving ambiguities in the coastline matchup analysis. Several geolocation and pointing bias sources were incfementally eliminated resulting in pointing knowledge and geolocation accuracy that met all design requirements.

Threatening communication: a critical re-analysis and a revised meta-analytic test of fear appeal theory

PubMed Central

Peters, Gjalt-Jorn Ygram; Ruiter, Robert A.C.; Kok, Gerjo

2013-01-01

Despite decades of research, consensus regarding the dynamics of fear appeals remains elusive. A meta-analysis was conducted that was designed to resolve this controversy. Publications that were included in previous meta-analyses were re-analysed, and a number of additional publications were located. The inclusion criteria were full factorial orthogonal manipulations of threat and efficacy, and measurement of behaviour as an outcome. Fixed and random effects models were used to compute mean effect size estimates. Meta-analysis of the six studies that satisfied the inclusion criteria clearly showed a significant interaction between threat and efficacy, such that threat only had an effect under high efficacy (d = 0.31), and efficacy only had an effect under high threat (d = 0.71). Inconsistency in results regarding the effectiveness of threatening communication can likely be attributed to flawed methodology. Proper tests of fear appeal theory yielded the theoretically hypothesised interaction effect. Threatening communication should exclusively be used when pilot studies indicate that an intervention successfully enhances efficacy. PMID:23772231

Vigilance system in rails for train hot point temperatures during circulation

NASA Astrophysics Data System (ADS)

Meca Meca, Francisco J.; Rodriguez Sanchez, Francisco J.; Mazo Quintas, Manuel; Garcia Dominguez, Juan J.; Fonolla Navarro, Rafael; Sebastian Martinez, Eduardo; Jimenez Calvo, Jose A.; Lillo Rodriguez, Diego; Garcia Garrido, Miguel A.

2000-06-01

Wheels, hubs and brake discs in a train during its circulation are under mechanical strains that make its temperature increase above the environment temperature. Mechanical defects in those elements produce an excessive friction and, as a consequence of it, an important increment of its temperature in relation to normal values. Detecting these anomalies is essential to avoid accidents and it is performed by fixed systems located next to rails which make infrared temperature measurements of hot points and send them to a supervisory station that takes the proper steps. The paper introduces the most important problems which must be dealt with during the designing stage of the measurement system. It also explains the solutions taken by the authors in order to assure the minimum operative aims demanded by the application. These problems includes: the choice of the detector and measurement method, communication with the supervisory station, and the environment conditions. Finally, the research lines followed by the authors in order to improve and extend the system's capabilities are explained.

Factors Associated With Poor Child Motor Vehicle Restraint on the USA-Mexico Border.

PubMed

Schrodt, Alexander; Huynh, Tam; Fitzgerald, Tamara N

Motor vehicle collisions (MVCs) are a significant cause of pediatric morbidity, particularly in low- to middle-income countries. We describe car seat use in children on the USA-Mexico border. A retrospective review was conducted for children 0-9 years old, admitted to the region's only Level I trauma center. Simultaneously, data were obtained from the SAFE KIDS database, a program that encourages car seat use through city checkpoints. There were 250 MVC admissions and nine fatalities in children 0-9 years old from 2010 to 2015. Nine percent of MVCs occurred in Mexico and 49% in El Paso, TX. Comparing trauma admissions to SAFE KIDS, there was some correlation between the location of MVCs and screening checkpoints (r = .50). There was a weaker correlation between injured children's neighborhoods and screening locations (r = .32). Only 37% of parents knew the crash history of the car seat and 3% were using a car seat previously involved in an MVC. While 96% of inspected children were placed appropriately in the backseat, 80% of children were found to be inappropriately restrained. Younger children more likely to be restrained (p < .05). Children from New Mexico and Mexico had the lowest rates of proper restraint and the highest injury severity scores. Proper use of car seats is a public health concern on the USA-Mexico border, and children are not properly restrained. Screening may be improved by focusing where at-risk children live and where most accidents occur. Restraint education is needed, particularly in New Mexico and Mexico.

Asymmetrical access to color and location in visual working memory.

PubMed

Rajsic, Jason; Wilson, Daryl E

2014-10-01

Models of visual working memory (VWM) have benefitted greatly from the use of the delayed-matching paradigm. However, in this task, the ability to recall a probed feature is confounded with the ability to maintain the proper binding between the feature that is to be reported and the feature (typically location) that is used to cue a particular item for report. Given that location is typically used as a cue-feature, we used the delayed-estimation paradigm to compare memory for location to memory for color, rotating which feature was used as a cue and which was reported. Our results revealed several novel findings: 1) the likelihood of reporting a probed object's feature was superior when reporting location with a color cue than when reporting color with a location cue; 2) location report errors were composed entirely of swap errors, with little to no random location reports; and 3) both colour and location reports greatly benefitted from the presence of nonprobed items at test. This last finding suggests that it is uncertainty over the bindings between locations and colors at memory retrieval that drive swap errors, not at encoding. We interpret our findings as consistent with a representational architecture that nests remembered object features within remembered locations.

WASTE HANDLING BUILDING VENTILATION SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

P.A. Kumar

2000-06-21

The Waste Handling Building Ventilation System provides heating, ventilation, and air conditioning (HVAC) for the contaminated, potentially contaminated, and uncontaminated areas of the Monitored Geologic Repository's (MGR) Waste Handling Building (WHB). In the uncontaminated areas, the non-confinement area ventilation system maintains the proper environmental conditions for equipment operation and personnel comfort. In the contaminated and potentially contaminated areas, in addition to maintaining the proper environmental conditions for equipment operation and personnel comfort, the contamination confinement area ventilation system directs potentially contaminated air away from personnel in the WHB and confines the contamination within high-efficiency particulate air (HEPA) filtration units. Themore » contamination confinement areas ventilation system creates airflow paths and pressure zones to minimize the potential for spreading contamination within the building. The contamination confinement ventilation system also protects the environment and the public by limiting airborne releases of radioactive or other hazardous contaminants from the WHB. The Waste Handling Building Ventilation System is designed to perform its safety functions under accident conditions and other Design Basis Events (DBEs) (such as earthquakes, tornadoes, fires, and loss of the primary electric power). Additional system design features (such as compartmentalization with independent subsystems) limit the potential for cross-contamination within the WHB. The system provides status of important system parameters and equipment operation, and provides audible and/or visual indication of off-normal conditions and equipment failures. The Waste Handling Building Ventilation System confines the radioactive and hazardous material within the building such that the release rates comply with regulatory limits. The system design, operations, and maintenance activities incorporate ALARA (as low as is reasonably achievable) principles to maintain personnel radiation doses to all occupational workers below regulatory limits and as low as is reasonably achievable. The Waste Handling Building Ventilation System interfaces with the Waste Handling Building System by being located within the WHB and by maintaining specific pressures, temperatures, and humidity within the building. The system also depends on the WHB for water supply. The system interfaces with the Site Radiological Monitoring System for continuous monitoring of the exhaust air; the Waste Handling Building Fire Protection System for detection of fire and smoke; the Waste Handling Building Electrical System for normal, emergency, and standby power; and the Monitored Geologic Repository Operations Monitoring and Control System for monitoring and control of the system.« less

The Correlation between Insertion Depth of Prodisc-C Artificial Disc and Postoperative Kyphotic Deformity: Clinical Importance of Insertion Depth of Artificial Disc.

PubMed

Lee, Do-Youl; Kim, Se-Hoon; Suh, Jung-Keun; Cho, Tai-Hyoung; Chung, Yong-Gu

2012-09-01

This study was designed to investigate the correlation between insertion depth of artificial disc and postoperative kyphotic deformity after Prodisc-C total disc replacement surgery, and the range of artificial disc insertion depth which is effective in preventing postoperative whole cervical or segmental kyphotic deformity. A retrospective radiological analysis was performed in 50 patients who had undergone single level total disc replacement surgery. Records were reviewed to obtain demographic data. Preoperative and postoperative radiographs were assessed to determine C2-7 Cobb's angle and segmental angle and to investigate postoperative kyphotic deformity. A formula was introduced to calculate insertion depth of Prodisc-C artificial disc. Statistical analysis was performed to search the correlation between insertion depth of Prodisc-C artificial disc and postoperative kyphotic deformity, and to estimate insertion depth of Prodisc-C artificial disc to prevent postoperative kyphotic deformity. In this study no significant statistical correlation was observed between insertion depth of Prodisc-C artificial disc and postoperative kyphotic deformity regarding C2-7 Cobb's angle. Statistical correlation between insertion depth of Prodisc-C artificial disc and postoperative kyphotic deformity was observed regarding segmental angle (p<0.05). It failed to estimate proper insertion depth of Prodisc-C artificial disc effective in preventing postoperative kyphotic deformity. Postoperative segmental kyphotic deformity is associated with insertion depth of Prodisc-C artificial disc. Anterior located artificial disc leads to lordotic segmental angle and posterior located artificial disc leads to kyphotic segmental angle postoperatively. But C2-7 Cobb's angle is not affected by artificial disc location after the surgery.

Three-dimensional analysis using finite element method of anterior teeth inclination and center of resistance location.

PubMed

Geramy, Allahyar; Sodagar, Ahmad; Hassanpour, Mehdi

2014-01-01

To locate the centre of resistance of consolidated units of four and six anterior teeth during retraction. Twelve three-dimensional (3D) models were designed in SolidWorks of the anterior segment with four and six teeth and their supporting structure. A proper force system was applied in each model to retract the teeth bodily. The exact location of the centre of resistances (CRes) was determined. It was found that the path of CRes change in four-tooth and six-tooth units according to the anterior teeth torque. A posterior shift of the CRes by increasing the inclination of teeth was shown. However, vertical position has a fluctuant behaviour. First it moves apically, then it moves incisally. Furthermore, results suggest that in en masse retraction, translation can be achieved with a smaller amount of moment-to-force ratio than in four-incisor retraction. In other words, for bodily retraction of anterior incisor segments, we should apply force in a more apical position. Different anterior torques between 7 and 35 degrees, cannot affect the CRes position dramatically. The area of CRes shifting is 0.92 mm (anterioposteriorly) x 0.74 mm (superior-inferiorly) in the six-tooth unit in the teeth model and 0.85 mm (anterioposteriorly) x 0.82 mm (superior-inferiorly) in the teeth and bone model. In the four-tooth model, the area of CRes shifting is 0.97 mm (anterioposteriorly) x 0.93 mm (superior-inferiorly) in tooth model and 0.77 mm (anterioposteriorly) x 0.87 mm (superior-inferiorly) in the teeth and bone model.

Improving psychotropic drug prescription in nursing home patients with dementia: design of a cluster randomized controlled trial

PubMed Central

2013-01-01

Background Neuropsychiatric symptoms are highly prevalent in nursing home patients with dementia. Despite modest effectiveness and considerable side effects, psychotropic drugs are frequently prescribed for these neuropsychiatric symptoms. This raises questions whether psychotropic drugs are appropriately prescribed. The aim of the PROPER (PRescription Optimization of Psychotropic drugs in Elderly nuRsing home patients with dementia) II study is to investigate the efficacy of an intervention for improving the appropriateness of psychotropic drug prescription in nursing home patients with dementia. Methods/design The PROPER II study is a multi-center cluster randomized controlled, pragmatic trial using parallel groups. It has a duration of eighteen months and four six-monthly assessments. Six nursing homes will participate in the intervention and six will continue care as usual. The nursing homes will be located throughout the Netherlands, each participating with two dementia special care units with an average of fifteen patients per unit, resulting in 360 patients. The intervention consists of a structured and repeated multidisciplinary medication review supported by education and continuous evaluation. It is conducted by pharmacists, physicians, and nurses and consists of three components: 1) preparation and education, 2) conduct, and 3) evaluation/guidance. The primary outcome is the proportion of patients with appropriate psychotropic drug use. Secondary outcomes are the overall frequency of psychotropic drug use, neuropsychiatric symptoms, quality of life, activities of daily living, psychotropic drug side effects and adverse events (including cognition, comorbidity, and mortality). Besides, a process analysis on the intervention will be carried out. Discussion This study is expected to improve the appropriateness of psychotropic drug prescription for neuropsychiatric symptoms in nursing home patients with dementia by introducing a structured and repeated multidisciplinary medication review supported by education and continuous evaluation. Trial registration Netherlands Trial Registry (NTR): NTR3569. PMID:24180295

Development of design guidelines for proper selection of graded aggregate base in Maryland state highways.

DOT National Transportation Integrated Search

2015-01-01

The mechanical and drainage properties of graded aggregate base material are the level one input in mechanistic : pavement design. Maryland State Highway Administration (SHA) is in need of guidelines for evaluation of stiffness : and drainage charact...

Linear time-invariant controller design for two-channel decentralized control systems

NASA Technical Reports Server (NTRS)

Desoer, Charles A.; Gundes, A. Nazli

1987-01-01

This paper analyzes a linear time-invariant two-channel decentralized control system with a 2 x 2 strictly proper plant. It presents an algorithm for the algebraic design of a class of decentralized compensators which stabilize the given plant.

User Interface Design for Dynamic Geometry Software

ERIC Educational Resources Information Center

Kortenkamp, Ulrich; Dohrmann, Christian

2010-01-01

In this article we describe long-standing user interface issues with Dynamic Geometry Software and common approaches to address them. We describe first prototypes of multi-touch-capable DGS. We also give some hints on the educational benefits of proper user interface design.

Committee Report: Metrics & Methods for MF/UF System Optimization

EPA Science Inventory

After a membrane filtration (i.e., microfiltration (MF) and ultrafiltration (UF)) system is designed, installed, and commissioned, it is essential that the plant is well-maintained in order to proactively identify potential design or equipment problems and ensure its proper opera...

Design philosophy and operating experience with the WNRE Hot Cell Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, R.G.; Seymour, C.G.; Ryz, M.A.

1969-10-15

The objective of radiation safety and operating efficiency often conflict. The key to preventing this conflict is proper design. In this paper we discuss how both objectives have been met in the Whiteshell Nuclear Research Establishment (WNRE) Hot Cell Facilities.

Structure and Management of an Engineering Senior Design Course.

PubMed

Tanaka, Martin L; Fischer, Kenneth J

2016-07-01

The design of products and processes is an important area in engineering. Students in engineering schools learn fundamental principles in their courses but often lack an opportunity to apply these methods to real-world problems until their senior year. This article describes important elements that should be incorporated into a senior capstone design course. It includes a description of the general principles used in engineering design and a discussion of why students often have difficulty with application and revert to trial and error methods. The structure of a properly designed capstone course is dissected and its individual components are evaluated. Major components include assessing resources, identifying projects, establishing teams, understanding requirements, developing conceptual designs, creating detailed designs, building prototypes, testing performance, and final presentations. In addition to the course design, team management and effective mentoring are critical to success. This article includes suggested guidelines and tips for effective design team leadership, attention to detail, investment of time, and managing project scope. Furthermore, the importance of understanding business culture, displaying professionalism, and considerations of different types of senior projects is discussed. Through a well-designed course and proper mentoring, students will learn to apply their engineering skills and gain basic business knowledge that will prepare them for entry-level positions in industry.

Sustainability Engineering and Maintenance - Plan, Design, and Construct for Maintainability: Sustainable Lighting Systems

DTIC Science & Technology

2011-01-01

Window film should be considered to control heat gain. Skylights when positioned and spaced properly with the proper lens systems, admit more light...per unit area than windows, and distribute the light more evenly over the space. Skylights are mainly recommended in single floor high bay...facilities such as warehouses, hangars, gymnasiums, and big box stores.  The optimum material to use for skylights is either glass or acrylic. Double

Medical management of youth baseball and softball tournaments.

PubMed

Kanaan, Matthew; Ray, Tracy R

2013-01-01

The medical management of youth baseball and softball tournaments requires both proper planning and a basic awareness of commonly seen sport-specific injuries. While youth sporting events are designed to be a fun experience for all, injuries and emergencies will occur. With proper planning, and supplies, the impact of these issues can be minimized. This article will outline some basic principles for the medical personnel that may be involved in youth baseball and softball events.

Classification of urine sediment based on convolution neural network

NASA Astrophysics Data System (ADS)

Pan, Jingjing; Jiang, Cunbo; Zhu, Tiantian

2018-04-01

By designing a new convolution neural network framework, this paper breaks the constraints of the original convolution neural network framework requiring large training samples and samples of the same size. Move and cropping the input images, generate the same size of the sub-graph. And then, the generated sub-graph uses the method of dropout, increasing the diversity of samples and preventing the fitting generation. Randomly select some proper subset in the sub-graphic set and ensure that the number of elements in the proper subset is same and the proper subset is not the same. The proper subsets are used as input layers for the convolution neural network. Through the convolution layer, the pooling, the full connection layer and output layer, we can obtained the classification loss rate of test set and training set. In the red blood cells, white blood cells, calcium oxalate crystallization classification experiment, the classification accuracy rate of 97% or more.

Handbook for Designing MMOD Protection

NASA Technical Reports Server (NTRS)

Arnold, Jim; Christiansen, Eric L.; Davis, Alan; Hyde, James; Lear, Dana; Liou, J.C.; Lyons, Frankel; Prior, Thomas; Studor, George; Ratliff, Martin;

Multichannel feedforward control schemes with coupling compensation for active sound profiling

NASA Astrophysics Data System (ADS)

Mosquera-Sánchez, Jaime A.; Desmet, Wim; de Oliveira, Leopoldo P. R.

2017-05-01

Active sound profiling includes a number of control techniques that enables the equalization, rather than the mere reduction, of acoustic noise. Challenges may rise when trying to achieve distinct targeted sound profiles simultaneously at multiple locations, e.g., within a vehicle cabin. This paper introduces distributed multichannel control schemes for independently tailoring structural borne sound reaching a number of locations within a cavity. The proposed techniques address the cross interactions amongst feedforward active sound profiling units, which compensate for interferences of the primary sound at each location of interest by exchanging run-time data amongst the control units, while attaining the desired control targets. Computational complexity, convergence, and stability of the proposed multichannel schemes are examined in light of the physical system at which they are implemented. The tuning performance of the proposed algorithms is benchmarked with the centralized and pure-decentralized control schemes through computer simulations on a simplified numerical model, which has also been subjected to plant magnitude variations. Provided that the representation of the plant is accurate enough, the proposed multichannel control schemes have been shown as the only ones that properly deliver targeted active sound profiling tasks at each error sensor location. Experimental results in a 1:3-scaled vehicle mock-up further demonstrate that the proposed schemes are able to attain reductions of more than 60 dB upon periodic disturbances at a number of positions, while resolving cross-channel interferences. Moreover, when the sensor/actuator placement is found as defective at a given frequency, the inclusion of a regularization parameter in the cost function is seen to not hinder the proper operation of the proposed compensation schemes, at the time that it assures their stability, at the expense of losing control performance.

Laboratory Experimental Design for a Glycomic Study.

PubMed

Ugrina, Ivo; Campbell, Harry; Vučković, Frano

2017-01-01

Proper attention to study design before, careful conduct of procedures during, and appropriate inference from results after scientific experiments are important in all scientific studies in order to ensure valid and sometimes definitive conclusions can be made. The design of experiments, also called experimental design, addresses the challenge of structuring and conducting experiments to answer the questions of interest as clearly and efficiently as possible.

Design and Development of the Space Shuttle Tail Service Masts

NASA Technical Reports Server (NTRS)

Dandage, S. R.; Herman, N. A.; Godfrey, S. E.; Uda, R. T.

1977-01-01

The successful launch of a space shuttle vehicle depends on the proper operation of two tail service masts (TSMs). Reliable TSM operation is assured through a comprehensive design, development, and testing program. The results of the concept verification test (CVT) and the resulting impact on prototype TSM design are presented. The design criteria are outlined, and the proposed prototype TSM tests are described.

Topology Optimization - Engineering Contribution to Architectural Design

NASA Astrophysics Data System (ADS)

Tajs-Zielińska, Katarzyna; Bochenek, Bogdan

2017-10-01

The idea of the topology optimization is to find within a considered design domain the distribution of material that is optimal in some sense. Material, during optimization process, is redistributed and parts that are not necessary from objective point of view are removed. The result is a solid/void structure, for which an objective function is minimized. This paper presents an application of topology optimization to multi-material structures. The design domain defined by shape of a structure is divided into sub-regions, for which different materials are assigned. During design process material is relocated, but only within selected region. The proposed idea has been inspired by architectural designs like multi-material facades of buildings. The effectiveness of topology optimization is determined by proper choice of numerical optimization algorithm. This paper utilises very efficient heuristic method called Cellular Automata. Cellular Automata are mathematical, discrete idealization of a physical systems. Engineering implementation of Cellular Automata requires decomposition of the design domain into a uniform lattice of cells. It is assumed, that the interaction between cells takes place only within the neighbouring cells. The interaction is governed by simple, local update rules, which are based on heuristics or physical laws. The numerical studies show, that this method can be attractive alternative to traditional gradient-based algorithms. The proposed approach is evaluated by selected numerical examples of multi-material bridge structures, for which various material configurations are examined. The numerical studies demonstrated a significant influence the material sub-regions location on the final topologies. The influence of assumed volume fraction on final topologies for multi-material structures is also observed and discussed. The results of numerical calculations show, that this approach produces different results as compared with classical one-material problems.

An experimental and numerical investigation of phase change electrodes for therapeutic irreversible electroporation.

PubMed

Arena, Christopher B; Mahajan, Roop L; Nichole Rylander, Marissa; Davalos, Rafael V

2013-11-01

Irreversible electroporation (IRE) is a new technology for ablating aberrant tissue that utilizes pulsed electric fields (PEFs) to kill cells by destabilizing their plasma membrane. When treatments are planned correctly, the pulse parameters and location of the electrodes for delivering the pulses are selected to permit destruction of the target tissue without causing thermal damage to the surrounding structures. This allows for the treatment of surgically inoperable masses that are located near major blood vessels and nerves. In select cases of high-dose IRE, where a large ablation volume is desired without increasing the number of electrode insertions, it can become challenging to design a pulse protocol that is inherently nonthermal. To solve this problem we have developed a new electrosurgical device that requires no external equipment or protocol modifications. The design incorporates a phase change material (PCM) into the electrode core that melts during treatment and absorbs heat out of the surrounding tissue. Here, this idea is reduced to practice by testing hollow electrodes filled with gallium on tissue phantoms and monitoring temperature in real time. Additionally, the experimental data generated are used to validate a numerical model of the heat transfer problem, which is then applied to investigate the cooling performance of other classes of PCMs. The results indicate that metallic PCMs, such as gallium, are better suited than organics or salt hydrates for thermal management, because their comparatively higher thermal conductivity aids in heat dissipation. However, the melting point of the metallic PCM must be properly adjusted to ensure that the phase transition is not completed before the end of treatment. When translated clinically, phase change electrodes have the potential to continue to allow IRE to be performed safely near critical structures, even in high-dose cases.

Patterning of alloy precipitation through external pressure

NASA Astrophysics Data System (ADS)

Franklin, Jack A.

Due to the nature of their microstructure, alloyed components have the benefit of meeting specific design goals across a wide range of electrical, thermal, and mechanical properties. In general by selecting the correct alloy system and applying a proper heat treatment it is possible to create a metallic sample whose properties achieve a unique set of design requirements. This dissertation presents an innovative processing technique intended to control both the location of formation and the growth rates of precipitates within metallic alloys in order to create multiple patterned areas of unique microstructure within a single sample. Specific experimental results for the Al-Cu alloy system will be shown. The control over precipitation is achieved by altering the conventional heat treatment process with an external surface load applied to selected locations during the quench and anneal. It is shown that the applied pressures affect both the rate and directionality of the atomic diffusion in regions close to the loaded surfaces. The control over growth rates is achieved by altering the enthalpic energy required for successful diffusion between lattice sites. Changes in the local chemical free energy required to direct the diffusion of atoms are established by introducing a non-uniform elastic strain energy field within the samples created by the patterned surface pressures. Either diffusion rates or atomic mobility can be selected as the dominating control process by varying the quench rate; with slower quenches having greater control over the mobility of the alloying elements. Results have shown control of Al2Cu precipitation over 100 microns on mechanically polished surfaces. Further experimental considerations presented will address consistency across sample ensembles. This includes repeatable pressure loading conditions and the chemical interaction between any furnace environments and both the alloy sample and metallic pressure loading devices.

Fishes of the big muddy river drainage with emphasis on historical changes

Treesearch

Brooks M. Burr; Melvin L. Warren

1999-01-01

The Big Muddy River, a lowland stream located in southwestern Illinois and draining an area of about 6,182 km2, contains a moderately diverse fish fauna of 106 species. The river is properly named, as the mainstem carried historically and continues to transport great quantities of silt. Historically, a large portion of the watershed was wooded,...

43 CFR 3832.42 - How do I locate a tunnel site?

Code of Federal Regulations, 2013 CFR

2013-10-01

... substantial post, board, or monument at the face of the tunnel, which is the point where the tunnel enters... height and width of the tunnel; and (4) The course and distance from the face or starting point to some... boundary lines of the tunnel at proper intervals as required under state law from the face of the tunnel...

43 CFR 3832.42 - How do I locate a tunnel site?

Code of Federal Regulations, 2012 CFR

2012-10-01

... substantial post, board, or monument at the face of the tunnel, which is the point where the tunnel enters... height and width of the tunnel; and (4) The course and distance from the face or starting point to some... boundary lines of the tunnel at proper intervals as required under state law from the face of the tunnel...

An Intuitive Graphical Approach to Understanding the Split-Plot Experiment

ERIC Educational Resources Information Center

Robinson, Timothy J.; Brenneman, William A.; Myers, William R.

2009-01-01

While split-plot designs have received considerable attention in the literature over the past decade, there seems to be a general lack of intuitive understanding of the error structure of these designs and the resulting statistical analysis. Typically, students learn the proper error terms for testing factors of a split-plot design via "expected…

A discussion of higher order software concepts as they apply to functional requirements and specifications. [space shuttles and guidance

NASA Technical Reports Server (NTRS)

Hamilton, M.

1973-01-01

The entry guidance software functional requirements (requirements design phase), its architectural requirements (specifications design phase), and the entry guidance software verified code are discussed. It was found that the proper integration of designs at both the requirements and specifications levels are of high priority consideration.

Designing Effective Safety Signs, Based on a Study of Recall for Safety Signs.

ERIC Educational Resources Information Center

Berry, Dennis W.

Aside from direct supervision at a recreational facility, safety signs, if designed properly, are the most effective approach to facility safety. This study was conducted to investigate the effectiveness of various sign designs: (l) multiple concepts with text; (2) single concept with text; and (3) single concept with graphics. A discussion of…

Mark of the Moessbauer

NASA Technical Reports Server (NTRS)

2004-01-01

This image, taken by an instrument called the microscopic imager on the Mars Exploration Rover Spirit, reveals an imprint left by another instrument, the Moessbauer spectrometer. The imprint is at a location within the rover wheel track named 'Middle of Road.' Both instruments are located on the rover's instrument deployment device, or 'arm.'

Not only was the Moessbauer spectrometer able to gain important mineralogical information about this site, it also aided in the placement of the microscopic imager. On hard rocks, the microscopic imager uses its tiny metal sensor to determine proper placement for best possible focus. However, on the soft martian soil this guide would sink, prohibiting proper placement of the microscopic imager. After the Moessbauer spectrometer's much larger, donut-shaped plate touches the surface, Spirit can correctly calculate where to position the microscopic imager.

Scientists find this image particularly interesting because of the compacted nature of the soil that was underneath the Moessbauer spectrometer plate. Also of interest are the embedded, round grains and the fractured appearance of the material disturbed within the hole. The material appears to be slightly cohesive. The field of view in this image, taken on Sol 43 (February 16, 2004), measures approximately 3 centimeters (1.2 inches) across.

Distances, Kinematics, And Structure Of The Orion Complex

NASA Astrophysics Data System (ADS)

Kounkel, Marina; Hartmann, Lee

2018-01-01

I present an analysis of the structure and kinematics of the Orion Molecular Cloud Complex in an effort to better characterize the dynamical state of the closest region of ongoing massive star formation. I measured stellar parallax and proper motions with <5% uncertainty using radio VLBI observations of non-thermally-emitting sources located in various star forming regions within the Orion Complex. This includes the first direct distance measurements for sources that are located outside of the Orion Nebula. I identified a number of binary systems in the VLBI dataset and fitted their orbital motion, which allows for the direct measurement of the masses of the individual components. Additionally, I have identified several stars that have been ejected from the Orion Nebula due to strong gravitational interactions with the most massive members. I complemented the parallax and proper motion measurements with the observations of optical radial velocities of the stars toward the Orion Complex, probing the histories of both dynamic evolution and star formation in the region, providing a 6-dimensional model of the Complex. These observations can serve as a baseline for comparison of the upcoming results from the Gaia space telescope

Dryden Flight Research Center Chemical Pharmacy Program

NASA Technical Reports Server (NTRS)

Davis, Bette

1997-01-01

The Dryden Flight Research Center (DFRC) Chemical Pharmacy "Crib" is a chemical sharing system which loans chemicals to users, rather than issuing them or having each individual organization or group purchasing the chemicals. This cooperative system of sharing chemicals eliminates multiple ownership of the same chemicals and also eliminates stockpiles. Chemical management duties are eliminated for each of the participating organizations. The chemical storage issues, hazards and responsibilities are eliminated. The system also ensures safe storage of chemicals and proper disposal practices. The purpose of this program is to reduce the total releases and transfers of toxic chemicals. The initial cost of the program to DFRC was $585,000. A savings of $69,000 per year has been estimated for the Center. This savings includes the reduced costs in purchasing, disposal and chemical inventory/storage responsibilities. DFRC has chemicals stored in 47 buildings and at 289 locations. When the program is fully implemented throughout the Center, there will be three chemical locations at this facility. The benefits of this program are the elimination of chemical management duties; elimination of the hazard associated with chemical storage; elimination of stockpiles; assurance of safe storage; assurance of proper disposal practices; assurance of a safer workplace; and more accurate emissions reports.

The Clusters AgeS Experiment (CASE). Variable Stars in the Field of the Globular Cluster M12

NASA Astrophysics Data System (ADS)

Kaluzny, J.; Thompson, I. B.; Narloch, W.; Pych, W.; Rozyczka, M.

2015-09-01

The field of the globular cluster M12 (NGC 6218) was monitored between 1995 and 2009 in a search for variable stars. BV light curves were obtained for thirty-six periodic or likely periodic variable stars. Thirty-four of these are new detections. Among the latter we identified twenty proper-motion members of the cluster: six detached or semi-detached eclipsing binaries, five contact binaries, five SX Phe pulsators, and three yellow stragglers. Two of the eclipsing binaries are located in the turnoff region, one on the lower main sequence and the remaining three among the blue stragglers. Two contact systems are blue stragglers, and the remaining three reside in the turnoff region. In the blue straggler region a total of 103 objects were found, of which 42 are proper motion members of M12, and another four are field stars. 55 of the remaining objects are located within two core radii from the center of the cluster, and as such they are likely genuine blue stragglers. We also report the discoveries of a radial color gradient of M12, and the shortest period among contact systems in globular clusters in general.

The Clusters AgeS Experiment (CASE). Variable Stars in the Field of the Globular Cluster NGC 6362

NASA Astrophysics Data System (ADS)

Kaluzny, J.; Thompson, I. B.; Rozyczka, M.; Pych, W.; Narloch, W.

2014-12-01

The field of the globular cluster NGC 6362 was monitored between 1995 and 2009 in a search for variable stars. BV light curves were obtained for 69 periodic variable stars including 34 known RR Lyr stars, 10 known objects of other types and 25 newly detected variable stars. Among the latter we identified 18 proper-motion members of the cluster: seven detached eclipsing binaries (DEBs), six SX Phe stars, two W UMa binaries, two spotted red giants, and a very interesting eclipsing binary composed of two red giants - the first example of such a system found in a globular cluster. Five of the DEBs are located at the turnoff region, and the remaining two are redward of the lower main sequence. Eighty-four objects from the central 9×9 arcmin2 of the cluster were found in the region of cluster blue stragglers. Of these 70 are proper motion (PM) members of NGC 6362 (including all SX Phe and two W UMa stars), and five are field stars. The remaining nine objects lacking PM information are located at the very core of the cluster, and as such they are likely genuine blue stragglers.

Analytical determination of propeller performance degradation due to ice accretion

NASA Technical Reports Server (NTRS)

Miller, T. L.

1986-01-01

A computer code has been developed which is capable of computing propeller performance for clean, glaze, or rime iced propeller configurations, thereby providing a mechanism for determining the degree of performance degradation which results from a given icing encounter. The inviscid, incompressible flow field at each specified propeller radial location is first computed using the Theodorsen transformation method of conformal mapping. A droplet trajectory computation then calculates droplet impingement points and airfoil collection efficiency for each radial location, at which point several user-selectable empirical correlations are available for determining the aerodynamic penalities which arise due to the ice accretion. Propeller performance is finally computed using strip analysis for either the clean or iced propeller. In the iced mode, the differential thrust and torque coefficient equations are modified by the drag and lift coefficient increments due to ice to obtain the appropriate iced values. Comparison with available experimental propeller icing data shows good agreement in several cases. The code's capability to properly predict iced thrust coefficient, power coefficient, and propeller efficiency is shown to be dependent on the choice of empirical correlation employed as well as proper specification of radial icing extent.

37 CFR 262.7 - Verification of royalty payments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Designated Agent have agreed as to proper verification methods. (b) Frequency of verification. A Copyright Owner or a Performer may conduct a single audit of the Designated Agent upon reasonable notice and... COPYRIGHT ARBITRATION ROYALTY PANEL RULES AND PROCEDURES RATES AND TERMS FOR CERTAIN ELIGIBLE...

Budget-Minded Renovation Lights Up Students' Learning.

ERIC Educational Resources Information Center

McDaniel, Craig

1998-01-01

Provides considerations for educational facility lighting designs that support student learning while controlling costs. Lighting design decision factors include the types of classroom activities involved, the importance of properly using artificial and indirect lighting, the importance of color rendering, the positioning of windows and skylights,…

Safe and Sanitary.

ERIC Educational Resources Information Center

Turner, Ed; Hauser, Dan

1994-01-01

Explains how daily maintenance and design planning can reduce the potential safety hazards found in athletic-facility locker rooms. Topics include designing locker rooms for visual openness and traffic control, providing non-slip surfaces and proper drainage, installing ventilation systems that can handle the moisture produced in locker rooms,…

Evaluation of drainage pipe by field experimentation and supplemental laboratory experimentation : final report.

DOT National Transportation Integrated Search

1985-03-01

Louisiana's Office of Highways reacts to a major problem when it attempts to shape and control drainage patterns along its right-of-ways. The Office's design engineers meet this challenge through proper section design and appropriate application of d...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

5 CFR 930.102 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... motor vehicle to properly carry out his or her assigned duties. Motor vehicle means a vehicle designed... vehicle (a) designed or used for military field training, combat, or tactical purposes; (b) used principally within the confines of a regularly established military post, camp, or depot; or (c) regularly...

Evaluation of drainage pipe by field experimentation and supplemental laboratory experimentation : interim report No. 3.

DOT National Transportation Integrated Search

1981-11-01

The Louisiana Department of Transportation and Development reacts to a major problem when it attempts to shape and control drainage patterns along its right-of-ways. The Department's design engineers meet this challenge through proper section design ...

Design and implementation of visualization methods for the CHANGES Spatial Decision Support System

NASA Astrophysics Data System (ADS)

Cristal, Irina; van Westen, Cees; Bakker, Wim; Greiving, Stefan

2014-05-01

The CHANGES Spatial Decision Support System (SDSS) is a web-based system aimed for risk assessment and the evaluation of optimal risk reduction alternatives at local level as a decision support tool in long-term natural risk management. The SDSS use multidimensional information, integrating thematic, spatial, temporal and documentary data. The role of visualization in this context becomes of vital importance for efficiently representing each dimension. This multidimensional aspect of the required for the system risk information, combined with the diversity of the end-users imposes the use of sophisticated visualization methods and tools. The key goal of the present work is to exploit efficiently the large amount of data in relation to the needs of the end-user, utilizing proper visualization techniques. Three main tasks have been accomplished for this purpose: categorization of the end-users, the definition of system's modules and the data definition. The graphical representation of the data and the visualization tools were designed to be relevant to the data type and the purpose of the analysis. Depending on the end-users category, each user should have access to different modules of the system and thus, to the proper visualization environment. The technologies used for the development of the visualization component combine the latest and most innovative open source JavaScript frameworks, such as OpenLayers 2.13.1, ExtJS 4 and GeoExt 2. Moreover, the model-view-controller (MVC) pattern is used in order to ensure flexibility of the system at the implementation level. Using the above technologies, the visualization techniques implemented so far offer interactive map navigation, querying and comparison tools. The map comparison tools are of great importance within the SDSS and include the following: swiping tool for comparison of different data of the same location; raster subtraction for comparison of the same phenomena varying in time; linked views for comparison of data from different locations and a time slider tool for monitoring changes in spatio-temporal data. All these techniques are part of the interactive interface of the system and make use of spatial and spatio-temporal data. Further significant aspects of the visualization component include conventional cartographic techniques and visualization of non-spatial data. The main expectation from the present work is to offer efficient visualization of risk-related data in order to facilitate the decision making process, which is the final purpose of the CHANGES SDSS. This work is part of the "CHANGES" project, funded by the European Community's 7th Framework Programme.

PROPER MOTIONS OF THE OUTER KNOTS OF THE HH 80/81/80N RADIO-JET

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masqué, Josep M.; Rodriguez, Luis F.; Carrasco-González, Carlos

2015-11-20

The radio-knots of the Herbig–Haro (HH) 80/81/80N jet extend from the HH 80 object to the recently discovered Source 34 and has a total projected jet size of 10.3 pc, constituting the largest collimated radio-jet system known so far. It is powered by the bright infrared source IRAS 18162−2048 associated with a massive young stellar object. We report 6 cm JVLA observations that, compared with previous 6 cm VLA observations carried out in 1989, allow us to derive proper motions of the HH 80, HH 81, and HH 80N radio knots located about 2.5 pc away in projection from themore » powering source. For the first time, we measure proper motions of the optically obscured HH 80N object providing evidence that this knot, along with HH 81 and HH 80 are associated with the same radio-jet. We also confirm the presence of Source 34, located further north of HH 80N, previously proposed to belong to the jet.We derived that the tangential velocity of HH 80N is 260 km s{sup −1} and has a direction in agreement with the expected direction of a ballistic precessing jet. The HH 80 and HH 81 objects have tangential velocities of 350 and 220 km s{sup −1}, respectively, but their directions are somewhat deviated from the expected jet path. The velocities of the HH objects studied in this work are significantly lower than those derived for the radio knots of the jet close to the powering source (600–1400 km s{sup −1}) suggesting that the jet is slowing down due to a strong interaction with the ambient medium. As a result, since HH 80 and HH 81 are located near the edge of the cloud, the inhomogeneous and low density medium may contribute to skew the direction of their determined proper motions. The HH 80 and HH 80N emission at 6 cm is, at least in part, probably synchrotron radiation produced by relativistic electrons in a magnetic field of 1 mG. If these electrons are accelerated in a reverse adiabatic shock, we estimate a jet total density of ≲1000 cm{sup −3}. All of these features are consistent with a jet emanating from a high-mass protostar and make evident its capability of accelerating particles up to relativistic velocities.« less

Development and manufacture of visor for helmet-mounted display

NASA Astrophysics Data System (ADS)

Krevor, David H.; McNelly, Gregg; Skubon, John; Speirs, Robert

2004-01-01

The manufacturing design and process development for the Visor for the JHMCS (Joint Helmet Mounted Cueing System) are discussed. The JHMCS system is a Helmet Mounted Display (HMD) system currently flying on the F-15, F-16 and F/A-18 aircraft. The Visor manufacturing processes are essential to both system performance and economy. The Visor functions both as the system optical combiner and personal protective equipment for the pilot. The Visor material is optical polycarbonate. For a military HMD system, the mechanical and environmental properties of the Visor are as necessary as the optical properties. The visor must meet stringent dimensional requirements to assure adequate system optical performance. Injection molding can provide dimensional fidelity to the requirements, if done properly. Concurrent design of the visor and the tool (i.e., the injection mold) is essential. The concurrent design necessarily considers manufacturing operations and the use environment of the Visor. Computer modeling of the molding process is a necessary input to the mold design. With proper attention to product design and tool development, it is possible to improve upon published standard dimensional tolerances for molded polycarbonate articles.

Authentication techniques for smart cards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, R.A.

1994-02-01

Smart card systems are most cost efficient when implemented as a distributed system, which is a system without central host interaction or a local database of card numbers for verifying transaction approval. A distributed system, as such, presents special card and user authentication problems. Fortunately, smart cards offer processing capabilities that provide solutions to authentication problems, provided the system is designed with proper data integrity measures. Smart card systems maintain data integrity through a security design that controls data sources and limits data changes. A good security design is usually a result of a system analysis that provides a thoroughmore » understanding of the application needs. Once designers understand the application, they may specify authentication techniques that mitigate the risk of system compromise or failure. Current authentication techniques include cryptography, passwords, challenge/response protocols, and biometrics. The security design includes these techniques to help prevent counterfeit cards, unauthorized use, or information compromise. This paper discusses card authentication and user identity techniques that enhance security for microprocessor card systems. It also describes the analysis process used for determining proper authentication techniques for a system.« less

Optical Correlation of Images With Signal-Dependent Noise Using Constrained-Modulation Filter Devices

NASA Technical Reports Server (NTRS)

Downie, John D.

1995-01-01

Images with signal-dependent noise present challenges beyond those of images with additive white or colored signal-independent noise in terms of designing the optimal 4-f correlation filter that maximizes correlation-peak signal-to-noise ratio, or combinations of correlation-peak metrics. Determining the proper design becomes more difficult when the filter is to be implemented on a constrained-modulation spatial light modulator device. The design issues involved for updatable optical filters for images with signal-dependent film-grain noise and speckle noise are examined. It is shown that although design of the optimal linear filter in the Fourier domain is impossible for images with signal-dependent noise, proper nonlinear preprocessing of the images allows the application of previously developed design rules for optimal filters to be implemented on constrained-modulation devices. Thus the nonlinear preprocessing becomes necessary for correlation in optical systems with current spatial light modulator technology. These results are illustrated with computer simulations of images with signal-dependent noise correlated with binary-phase-only filters and ternary-phase-amplitude filters.

Computational Investigation of the NASA Cascade Cyclonic Separation Device

NASA Technical Reports Server (NTRS)

Hoyt, Nathaniel C.; Kamotani, Yasuhiro; Kadambi, Jaikrishnan; McQuillen, John B.; Sankovic, John M.

2008-01-01

Devices designed to replace the absent buoyancy separation mechanism within a microgravity environment are of considerable interest to NASA as the functionality of many spacecraft systems are dependent on the proper sequestration of interpenetrating gas and liquid phases. Inasmuch, a full multifluid Euler-Euler computational fluid dynamics investigation has been undertaken to evaluate the performance characteristics of one such device, the Cascade Cyclonic Separator, across a full range of inlet volumetric quality with combined volumetric injection rates varying from 1 L/min to 20 L/min. These simulations have delimited the general modes of operation of this class of devices and have proven able to describe the complicated vortex structure and induced pressure gradients that arise. The computational work has furthermore been utilized to analyze design modifications that enhance the overall performance of these devices. The promising results indicate that proper CFD modeling may be successfully used as a tool for microgravity separator design.

Studying the Pair WDS 01487+7528 = HJ 2075 AB Using the GAIA-DR1 Data

NASA Astrophysics Data System (ADS)

Romero, Francisco Rica

2018-01-01

In September 2016, the European Space Agency (ESA) released GAIA-DR1. ESA also published TGAS, a subset of Gaia source comprising those stars in the Hipparcos and Tycho-2 catalogs for which a full 5-parameters astrometric solution have been achieved. After publication of TGAS, the author decided to use the parallaxes and proper motions to review the double stars studied by LIADA’s Double Star Section during 2003. This year LIADA measured and studied 103 pairs of which only 10 have both stellar components listed in TGAS. Of those 10 pairs, 80% (8 double stars) are optical and only 2 are physical (with common parallaxes and proper motions).The main object of this work is a new study of HJ 2075 AB (WDS 01487+7528), located at 60 pc and composed of stars of 10.0 and 11.3 magnitudes with spectral types G8V and K4V separated by 31". This is a physical pair according to TGAS data (common parallaxes and proper motions).

VizieR Online Data Catalog: WD+dMs from the SUPERBLINK proper motion survey (Skinner+, 2017)

NASA Astrophysics Data System (ADS)

Skinner, J. N.; Morgan, D. P.; West, A. A.; Lepine, S.; Thorstensen, J. R.

2018-06-01

To select for nearby WD+dMs, we used the SUPERBLINK proper motion survey (Lepine et al. 2002, J/AJ/124/1190; Lepine & Shara 2005, Cat. I/298), an ongoing all-sky survey that identifies and characterizes stars with proper motions μ>40 mas/yr. For this study, we used the 2011 July version of SUPERBLINK, which listed 2270481 stars, and was estimated to be >90% complete to V=19.0. We selected WD+dMs based on a combination of V magnitudes derived from the DSS plates (see Lepine & Shara 2005, Cat. I/298), near-UV magnitudes from GALEX, and Ks magnitudes from 2MASS. Using the UV-optical-IR color selection outlined in Skinner et al. (2014AJ....148..115S), we selected targets for spectroscopic follow-up (see bottom panel of Figure 1). We acquired optical spectroscopy of 178 newly identified WD+dM candidates, with the Boller and Chivens CCD spectrograph (CCDS), using both the Hiltner 2.4 m and McGraw-Hill 1.3 m telescopes located at the MDM Observatory. (3 data files).

Time-dependent constitutive modeling of drive belts—II. The effect of the shape of material retardation spectrum on the strain accumulation process

NASA Astrophysics Data System (ADS)

Zupančič, B.; Emri, I.

2009-11-01

This is the second paper in the series addressing the constitutive modeling of dynamically loaded elastomeric products such as power transmission belts. During the normal operation of such belts certain segments of the belt structure are loaded via tooth-like cyclical loading. When the time-dependent properties of the elastomeric material “match” the time-scale of the dynamic loading a strain accumulation (incrementation) process occurs. It was shown that the location of a critical rotation speed strongly depends on the distribution (shape) of the retardation spectrum, whereas the magnitude of the accumulated strain is governed by the strength of the corresponding spectrum lines. These interrelations are extremely non-linear. The strain accumulation process is most intensive at the beginning of the drive belt operation, and is less intensive for longer belts. The strain accumulation process is governed by the spectrum lines that are positioned within a certain region, which we call the Strain Accumulation Window (SAW). An SAW is always located to the right of the spectrum line, L i , at log ( ω λ i )=0, where ω is the operational angular velocity. The width of the SAW depends on the width of the material spectrum. Based on the following analysis a new designing criterion is proposed for use in engineering applications for selecting a proper material for general drive-belt operations.

Research on the autumn irrigation schedule of Hetao Irrigation District of China

NASA Astrophysics Data System (ADS)

Han, Y.

2016-12-01

Salinization of soil has great influence on the function of crop land, leading to the crop failure to some extent. One of the inducement of salinization is that the water pressure of frozen soil is lower than that of unfrozen, salt is drew up to the frozen layer along with water during the freezing process. To prevent the salinization of soil, people carry out the autumn irrigation in Hetao Irrigation District which located is located in Bayannur City, Inner Mongolia, north of China. Autumn irrigation is an irrigation event before the freezing of soil, the function of autumn irrigation includes soil moisture conservation, loosening the soil and leaching the salt. Among all the crop models, none is designed to simulate the water and salt movement during freezing and thawing progress. So In this study, SWAP (Soil Water Atmosphere Plant) model is modified by adding the freezing and thawing module which enable the model to take into consideration the effect of freezing and thawing on water and salt movement. After validating the modified model using field data and lab test results, the model was used to simulate the results of various autumn irrigation schedules, exploring the influence of different autumn irrigation amounts on the water, salt and heat condition and transportation of soil. Finally, proper autumn irrigation schedule was obtained to instruct the production of Hetao Irrigation District.

Characterization of the hydraulic performance of a gully under drainage conditions.

PubMed

Martins, Ricardo; Leandro, Jorge; de Carvalho, Rita Fernandes

2014-01-01

During rainfall events with low return periods (1-20 years) the drainage system can provide some degree of protection to urban areas. The system design is based not only on good hydraulic performance of the surface and the sewer network but also on their linking elements. Although the linking elements are of utmost importance as they allow the exchange of flow between the surface and the sewer network, there is a lack of studies that thoroughly characterize them. One crucial structural part of those elements is the gully. State-of-the-art dual-drainage models often use simplified formulae to replicate the gully hydraulic behaviour that lacks proper validation. This work focuses on simulating, both numerically and experimentally, the hydraulic performance of a 0.6 × 0.3 × 0.3 [m] (L × W × D) gully located inside an 8 × 0.5 × 0.5 [m] rectangular channel. The numerical simulations are conducted with the OpenFOAM toolbox and validated with water level measurements in the Multiple-Linking-Element experimental installation located at the Laboratory of Hydraulics of the University of Coimbra. The results provide a complete three-dimensional insight of the hydraulic behaviour of the flow inside the gully, and discharge coefficient formulae are disclosed that can be directly applied in dual-drainage models as internal boundary conditions.

78 FR 49520 - Scientific Information Request on Imaging Techniques for the Surveillance, Diagnosis, and Staging...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-14

... conducting this comparative effectiveness review pursuant to Section 1013 of the Medicare Prescription Drug... summary, including the following elements: study number, study period, design, methodology, indication and... period, design, methodology, indication and diagnosis, proper use instructions, inclusion and exclusion...

Turbopump systems for liquid rocket engines

NASA Technical Reports Server (NTRS)

1974-01-01

The turbopump system, from preliminary design through rocket engine testing is examined. Selection of proper system type for each application and integration of the components into a working system are dealt with. Details are also given on the design of various components including inducers, pumps, turbines, gears, and bearings.

Evaluation of drainage pipe by field experimentation and supplemental laboratory experimentation : interim report No. 2.

DOT National Transportation Integrated Search

1978-03-01

Louisiana's Office of Highways reacts to a major problem when it attempts to shape and control drainage patterns along its right-of-ways. The Office's design engineers meet this challenge through proper section design and appropriate application of d...

Evaluation of drainage pipe by field experimentation and supplemental laboratory experimentation : interim report No. 1.

DOT National Transportation Integrated Search

1977-03-01

Louisiana's Office of Highways reacts to a major problem when it attempts to shape and control drainage patterns along its right-of-ways. The Office's design engineers meet this challenge through proper section design and appropriate application of d...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2010 CFR

2010-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2011 CFR

2011-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2013 CFR

2013-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2012 CFR

2012-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

19 CFR 122.11 - Designation as international airport.

Code of Federal Regulations, 2014 CFR

2014-04-01

...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Classes of Airports § 122.11 Designation as international... useful. (c) Providing office space to the Federal Government. Each international airport shall provide, without cost to the Federal Government, proper office and other space for the sole use of Federal...

30 CFR 19.7 - Protection against explosion hazard.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion hazards..., if the lamp is designed and constructed to prevent the ignition of explosive mixtures of methane and...

30 CFR 19.7 - Protection against explosion hazard.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion hazards..., if the lamp is designed and constructed to prevent the ignition of explosive mixtures of methane and...

30 CFR 19.7 - Protection against explosion hazard.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion hazards..., if the lamp is designed and constructed to prevent the ignition of explosive mixtures of methane and...

30 CFR 19.7 - Protection against explosion hazard.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion hazards..., if the lamp is designed and constructed to prevent the ignition of explosive mixtures of methane and...

On-farm irrigatrion system design and operation

USDA-ARS?s Scientific Manuscript database

Most commercial blueberry fields are irrigated by overhead sprinklers or drip. Water is typically applied one to two times per week as needed with sprinklers, and every one to three days with drip. Sprinkler systems are relatively simple to install and maintain, and when designed properly, obtain re...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2014 CFR

2014-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2011 CFR

2011-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2012 CFR

2012-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2013 CFR

2013-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

29 CFR 1607.1 - Statement of purpose.

Code of Federal Regulations, 2010 CFR

2010-07-01

... incorporate a single set of principles which are designed to assist employers, labor organizations, employment... are designed to provide a framework for determining the proper use of tests and other selection procedures. These guidelines do not require a user to conduct validity studies of selection procedures where...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2013 CFR

2013-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2011 CFR

2011-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2014 CFR

2014-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2012 CFR

2012-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

14 CFR 23.1351 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

.../alternator. (5) Each generator/alternator must have an overvoltage control designed and installed to prevent... control and protective devices, must be able to furnish the required power at the proper voltage to each... detrimental substances, and mechanical damage; and (iii) So designed that the risk of electrical shock to crew...

Locker-Room Talk.

ERIC Educational Resources Information Center

Lowe, Jason; Noyes, Brad

1999-01-01

Explains how proper athletic facility locker-room design can save time and money. Design factors that address who will be using the facility are discussed as are user requirements, such as preparation areas, total storage area per user, grooming area, and security areas. Final comments address maintenance and operations issues. (GR)

Latest in tire burning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Betzig, H.M.

1996-12-31

On September 26, Cris Lombardi and I presented a paper at the ARIPPA. The economic and environmental advantages available to CFB operators through the firing of tire-derived fuel (TDF) are discussed. The bottom line savings to the operation can be significant. It is believed that a regional scrap tire processing facility, capable of making properly-sized fuel, can be supported in Pennsylvania. An effort to develop such an operation is described. The technology for shredding and sizing TDF is well-proven. The proper equipment has been identified and reliable sources of scrap tires have been located. What is needed is to establishmore » a certain minimum annual TDF usage so that fuel user permit modification activity can begin. Data are presented on the production and use of TDF.« less

Interaction of a pulsar with interstellar matter

NASA Astrophysics Data System (ADS)

Istomin, Ya. N.

1994-03-01

An increase of the rate of spin-down dot-P and emergence of a Magnus force acting on the star is connected with the appearance of a dense hydrogen plasma in the region of light surface. These effects are proportional to the permittivity epsilon = 1 + c2/(VA)2, where vA is the Alfven velocity in the vicinity of the light cylinder. During its lifetime, a pulsar can change the direction of its proper velocity and leave the Galactic plane. For the pulsar PSR 1757-24 located in the nebula G5.4-1.2, it is shown that due to the changing value of dot-P its characteristic age increases up to 7.5 x 104 years and the proper velocity decreases in magnitude to the order of 400km/s.

The ArcB Leucine Zipper Domain Is Required for Proper ArcB Signaling

PubMed Central

Nuñez Oreza, Luis Alberto; Alvarez, Adrián F.; Arias-Olguín, Imilla I.; Torres Larios, Alfredo; Georgellis, Dimitris

2012-01-01

The Arc two-component system modulates the expression of numerous genes in response to respiratory growth conditions. This system comprises ArcA as the response regulator and ArcB as the sensor kinase. ArcB is a tripartite histidine kinase whose activity is regulated by the oxidation of two cytosol-located redox-active cysteine residues that participate in intermolecular disulfide bond formation. Here, we report that the ArcB protein segment covering residues 70–121, fulfills the molecular characteristics of a leucine zipper containing coiled coil structure. Also, mutational analyses of this segment reveal three different phenotypical effects to be distributed along the coiled coil structure of ArcB, demonstrating that this motif is essential for proper ArcB signaling. PMID:22666479

Helicopter noise research at the Langley V/STOL tunnel

NASA Technical Reports Server (NTRS)

Hoad, D. R.; Green, G. C.

1978-01-01

The noise generated from a 1/4-scale AH-1G helicopter configuration was investigated in the Langley V/STOL tunnel. Microphones were installed in positions scaled to those for which flight test data were available. Model and tunnel conditions were carefully set to properly scaled flight conditions. Data presented indicate a high degree of similarity between model and flight test results. It was found that the pressure time history waveforms are very much alike in shape and amplitude. Blade slap when it occurred seemed to be generated in about the same location in the rotor disk as on the flight vehicle. If model and tunnel conditions were properly matched, including inflow turbulence characteristics, the intensity of the blade-slap impulse seemed to correlate well with flight.

Design and development of Hoeken's structural dynamic linkage based agro-tiller machine

NASA Astrophysics Data System (ADS)

Hynes, N. Rajesh Jesudoss; Saran, K.; Pavithran, V.

2018-05-01

India is one of biggest exporters of medicinal plants, spices and other many agro products in the world. Owing to the special needs, an agricultural machine is designed using Hoeken linkage with Pantograph mechanism and developed that ensures safety digging to uproot the plant. Thus, the focus is to cut the plant by machine with proper care and shoot system is cut properly avoiding any damage to the upper part of the plant and rather be cut in the root area to use it. This is done by the agricultural cutting machine by the name "agricultural tiller machine" that can perform the action same as the objective needed for the effective production of raw materials for manufacturing of the agro products.

A Method for Computing Leading-Edge Loads

NASA Technical Reports Server (NTRS)

Rhode, Richard V; Pearson, Henry A

1933-01-01

In this report a formula is developed that enables the determination of the proper design load for the portion of the wing forward of the front spar. The formula is inherently rational in concept, as it takes into account the most important variables that affect the leading-edge load, although theoretical rigor has been sacrificed for simplicity and ease of application. Some empirical corrections, based on pressure distribution measurements on the PW-9 and M-3 airplanes have been introduced to provide properly for biplanes. Results from the formula check experimental values in a variety of cases with good accuracy in the critical loading conditions. The use of the method for design purposes is therefore felt to be justified and is recommended.

Designing Adaptive Low Dissipative High Order Schemes

NASA Technical Reports Server (NTRS)

Yee, H. C.; Sjoegreen, B.; Parks, John W. (Technical Monitor)

2002-01-01

Proper control of the numerical dissipation/filter to accurately resolve all relevant multiscales of complex flow problems while still maintaining nonlinear stability and efficiency for long-time numerical integrations poses a great challenge to the design of numerical methods. The required type and amount of numerical dissipation/filter are not only physical problem dependent, but also vary from one flow region to another. This is particularly true for unsteady high-speed shock/shear/boundary-layer/turbulence/acoustics interactions and/or combustion problems since the dynamics of the nonlinear effect of these flows are not well-understood. Even with extensive grid refinement, it is of paramount importance to have proper control on the type and amount of numerical dissipation/filter in regions where it is needed.

Design Recommendations for Query Languages

DTIC Science & Technology

1980-09-01

DESIGN RECOMMENDATIONS FOR QUERY LANGUAGES S.L. Ehrenreich Submitted by: Stanley M. Halpin, Acting Chief HUMAN FACTORS TECHNICAL AREA Approved by: Edgar ...respond to que- ries that it recognizes as faulty. Codd (1974) states that in designing a nat- ural query language, attention must be given to dealing...impaired. Codd (1974) also regarded the user’s perception of the data base to be of critical importance in properly designing a query language system

Development of a downhole tool measuring real-time concentration of ionic tracers and pH in geothermal reservoirs

NASA Astrophysics Data System (ADS)

Hess, Ryan F.; Boyle, Timothy J.; Limmer, Steven; Yelton, William G.; Bingham, Samuel; Stillman, Greg; Lindblom, Scott; Cieslewski, Grzegorz

2014-06-01

For enhanced or Engineered Geothermal Systems (EGS) geothermal brine is pumped to the surface via the production wells, the heat extracted to turn a turbine to generate electricity, and the spent brine re-injected via injection wells back underground. If designed properly, the subsurface rock formations will lead this water back to the extraction well as heated brine. Proper monitoring of these geothermal reservoirs is essential for developing and maintaining the necessary level of productivity of the field. Chemical tracers are commonly used to characterize the fracture network and determine the connectivity between the injection and production wells. Currently, most tracer experiments involve injecting the tracer at the injection well, manually collecting liquid samples at the wellhead of the production well, and sending the samples off for laboratory analysis. While this method provides accurate tracer concentration data at very low levels of detection, it does not provide information regarding the location of the fractures which were conducting the tracer between wellbores. Sandia is developing a high-temperature electrochemical sensor capable of measuring tracer concentrations and pH downhole on a wireline tool. The goal of this effort is to collect real-time pH and ionic tracer concentration data at temperatures up to 225 °C and pressures up to 3000 psi. In this paper, a prototype electrochemical sensor and the initial data obtained will be presented detailing the measurement of iodide tracer concentrations at high temperature and pressure in a newly developed laboratory scale autoclave.

JWST Integrated Science Instrument Module Alignment Optimization Tool

NASA Technical Reports Server (NTRS)

Bos, Brent

2013-01-01

During cryogenic vacuum testing of the James Webb Space Telescope (JWST) Integrated Science Instrument Module (ISIM), the global alignment of the ISIM with respect to the designed interface of the JWST optical telescope element (OTE) will be measured through a series of optical characterization tests. These tests will determine the locations and orientations of the JWST science instrument projected focal surfaces and entrance pupils with respect to their corresponding OTE optical interfaces. If any optical performance non-compliances are identified, the ISIM will be adjusted to improve its performance. In order to understand how to manipulate the ISIM's degrees of freedom properly and to prepare for the ISIM flight model testing, a series of optical-mechanical analyses have been completed to develop and identify the best approaches for bringing a non-compliant ISIM element into compliance. In order for JWST to meet its observatory-level optical requirements and ambitious science goals, the ISIM element has to meet approximately 150 separate optical requirements. Successfully achieving many of those optical requirements depends on the proper alignment of the ISIM element with respect to the OTE. To verify that the ISIM element will meet its optical requirements, a series of cryogenic vacuum tests will be conducted with an OTE Simulator (OSIM). An optical Ray Trace and Geometry Model tool was developed to help solve the multi-dimensional alignment problem. The tool allows the user to determine how best to adjust the alignment of the JWST ISIM with respect to the ideal telescope interfaces so that the approximately 150 ISIM optical performance requirements can be satisfied. This capability has not existed previously.

Prey preference of snow leopard (Panthera uncia) in South Gobi, Mongolia.

PubMed

Shehzad, Wasim; McCarthy, Thomas Michael; Pompanon, Francois; Purevjav, Lkhagvajav; Coissac, Eric; Riaz, Tiayyba; Taberlet, Pierre

2012-01-01

Accurate information about the diet of large carnivores that are elusive and inhabit inaccessible terrain, is required to properly design conservation strategies. Predation on livestock and retaliatory killing of predators have become serious issues throughout the range of the snow leopard. Several feeding ecology studies of snow leopards have been conducted using classical approaches. These techniques have inherent limitations in their ability to properly identify both snow leopard feces and prey taxa. To examine the frequency of livestock prey and nearly-threatened argali in the diet of the snow leopard, we employed the recently developed DNA-based diet approach to study a snow leopard population located in the Tost Mountains, South Gobi, Mongolia. After DNA was extracted from the feces, a region of ∼100 bp long from mitochondrial 12S rRNA gene was amplified, making use of universal primers for vertebrates and a blocking oligonucleotide specific to snow leopard DNA. The amplicons were then sequenced using a next-generation sequencing platform. We observed a total of five different prey items from 81 fecal samples. Siberian ibex predominated the diet (in 70.4% of the feces), followed by domestic goat (17.3%) and argali sheep (8.6%). The major part of the diet was comprised of large ungulates (in 98.8% of the feces) including wild ungulates (79%) and domestic livestock (19.7%). The findings of the present study will help to understand the feeding ecology of the snow leopard, as well as to address the conservation and management issues pertaining to this wild cat.

Prey Preference of Snow Leopard (Panthera uncia) in South Gobi, Mongolia

PubMed Central

Shehzad, Wasim; McCarthy, Thomas Michael; Pompanon, Francois; Purevjav, Lkhagvajav; Coissac, Eric; Riaz, Tiayyba; Taberlet, Pierre

2012-01-01

Accurate information about the diet of large carnivores that are elusive and inhabit inaccessible terrain, is required to properly design conservation strategies. Predation on livestock and retaliatory killing of predators have become serious issues throughout the range of the snow leopard. Several feeding ecology studies of snow leopards have been conducted using classical approaches. These techniques have inherent limitations in their ability to properly identify both snow leopard feces and prey taxa. To examine the frequency of livestock prey and nearly-threatened argali in the diet of the snow leopard, we employed the recently developed DNA-based diet approach to study a snow leopard population located in the Tost Mountains, South Gobi, Mongolia. After DNA was extracted from the feces, a region of ∼100 bp long from mitochondrial 12S rRNA gene was amplified, making use of universal primers for vertebrates and a blocking oligonucleotide specific to snow leopard DNA. The amplicons were then sequenced using a next-generation sequencing platform. We observed a total of five different prey items from 81 fecal samples. Siberian ibex predominated the diet (in 70.4% of the feces), followed by domestic goat (17.3%) and argali sheep (8.6%). The major part of the diet was comprised of large ungulates (in 98.8% of the feces) including wild ungulates (79%) and domestic livestock (19.7%). The findings of the present study will help to understand the feeding ecology of the snow leopard, as well as to address the conservation and management issues pertaining to this wild cat. PMID:22393381

Compliance Patterns and Utilization of e-Health for Glucose Monitoring: Standalone Internet Gateway and Tablet Device.

PubMed

Rho, Mi Jung; Kim, Hun-Sung; Yoon, Kun-Ho; Choi, In Young

2017-04-01

Knowledge regarding compliance patterns and service utilization in e-health is important for the development of effective services. To develop proper e-health, the characteristics of compliance patterns and utilization of e-health should be studied. We studied these for glucose monitoring of diabetic patients from primary clinics. Data were collected from 160 outpatients who participated in e-health for glucose monitoring funded by the Korean government. Specifically, this study focused on two device types: a standalone Internet gateway and a tablet device. The SPSS 18.0 software was used for statistical analyses of demographic characteristics, survival data, and Cox proportional hazards regression model. Standalone Internet gateway users demonstrated a more stable compliance pattern than did tablet device users. The compliance rate differed according to the device type. Typically, compliance decreases considerably around 8 months. In these results, standalone Internet gateway users utilized the service for longer periods than tablet device users. Gateway type and location also influenced utilization (p < 0.05). The service should be designed according to the device type to develop appropriate service models. Thus, service designers should understand the different characteristics of service devices. This study provides insight into compliance patterns and utilization to develop appropriate service models and service interventions depending on the device.

Statistical Analysis of 30 Years Rainfall Data: A Case Study

NASA Astrophysics Data System (ADS)

Arvind, G.; Ashok Kumar, P.; Girish Karthi, S.; Suribabu, C. R.

2017-07-01

Rainfall is a prime input for various engineering design such as hydraulic structures, bridges and culverts, canals, storm water sewer and road drainage system. The detailed statistical analysis of each region is essential to estimate the relevant input value for design and analysis of engineering structures and also for crop planning. A rain gauge station located closely in Trichy district is selected for statistical analysis where agriculture is the prime occupation. The daily rainfall data for a period of 30 years is used to understand normal rainfall, deficit rainfall, Excess rainfall and Seasonal rainfall of the selected circle headquarters. Further various plotting position formulae available is used to evaluate return period of monthly, seasonally and annual rainfall. This analysis will provide useful information for water resources planner, farmers and urban engineers to assess the availability of water and create the storage accordingly. The mean, standard deviation and coefficient of variation of monthly and annual rainfall was calculated to check the rainfall variability. From the calculated results, the rainfall pattern is found to be erratic. The best fit probability distribution was identified based on the minimum deviation between actual and estimated values. The scientific results and the analysis paved the way to determine the proper onset and withdrawal of monsoon results which were used for land preparation and sowing.

Developing daisy chain receivers for light-emitting diode illumination adopting the digital multiplex-512 protocol.

PubMed

Um, Keehong; Yoo, Sooyeup

2013-10-01

Protocol for digital multiplex with 512 pieces of information is increasingly adopted in the design of illumination systems. In conventional light-emitting diode systems, the receivers are connected in parallel and each of the receiving units receives all the data from the master dimmer console, but each receiving unit operates by recognizing as its own data that which corresponds to the assigned number of the receiver. Because the serial numbers of illumination devices are transmitted in binary code, synchronization is too complicated to be used properly. In order to improve the protocol of illumination control systems, we propose an algorithm of protocol reception to install and manage the system in a simpler and more convenient way. We propose the systems for controlling the light-emitting diode illumination of simplified receiver slaves adopting the digital multiplex-512 protocol where master console and multiple receiver slaves are connected in a daisy chain fashion. The digital multiplex-512 data packet is received according to the sequence order of their locations from the console, without assigning the sequence number of each channel at the receiving device. The purpose of this paper is to design a simple and small-sized controller for the control systems of lamps and lighting adopting the digital multiplex-512 network.

Intelligent design optimization of a shape-memory-alloy-actuated reconfigurable wing

NASA Astrophysics Data System (ADS)

Lagoudas, Dimitris C.; Strelec, Justin K.; Yen, John; Khan, Mohammad A.

2000-06-01

The unique thermal and mechanical properties offered by shape memory alloys (SMAs) present exciting possibilities in the field of aerospace engineering. When properly trained, SMA wires act as linear actuators by contracting when heated and returning to their original shape when cooled. It has been shown experimentally that the overall shape of an airfoil can be altered by activating several attached SMA wire actuators. This shape-change can effectively increase the efficiency of a wing in flight at several different flow regimes. To determine the necessary placement of these wire actuators within the wing, an optimization method that incorporates a fully-coupled structural, thermal, and aerodynamic analysis has been utilized. Due to the complexity of the fully-coupled analysis, intelligent optimization methods such as genetic algorithms have been used to efficiently converge to an optimal solution. The genetic algorithm used in this case is a hybrid version with global search and optimization capabilities augmented by the simplex method as a local search technique. For the reconfigurable wing, each chromosome represents a realizable airfoil configuration and its genes are the SMA actuators, described by their location and maximum transformation strain. The genetic algorithm has been used to optimize this design problem to maximize the lift-to-drag ratio for a reconfigured airfoil shape.

Coalbed natural gas exploration, drilling activities, and geologic test results, 2007-2010

USGS Publications Warehouse

Clark, Arthur C.

2014-01-01

The U.S. Geological Survey, in partnership with the U.S. Bureau of Land Management, the North Slope Borough, and the Arctic Slope Regional Corporation conducted a four-year study designed to identify, define, and delineate a shallow coalbed natural gas (CBNG) resource with the potential to provide locally produced, affordable power to the community of Wainwright, Alaska. From 2007 through 2010, drilling and testing activities conducted at three sites in or near Wainwright, identified and evaluated an approximately 7.5-ft-thick, laterally continuous coalbed that contained significant quantities of CBNG. This coalbed, subsequently named the Wainwright coalbed, was penetrated at depths ranging from 1,167 ft to 1,300 ft below land surface. Core samples were collected from the Wainwright coalbed at all three drill locations and desorbed-gas measurements were taken from seventeen 1-ft-thick sections of the core. These measurements indicate that the Wainwright coalbed contains enough CBNG to serve as a long-term energy supply for the community. Although attempts to produce viable quantities of CBNG from the Wainwright coalbed proved unsuccessful, it seems likely that with proper well-field design and by utilizing currently available drilling and reservoir stimulation techniques, this CBNG resource could be developed as a long-term economically viable energy source for Wainwright.