Efficacy of side air bags in reducing driver deaths in driver-side collisions.

PubMed

Braver, Elisa R; Kyrychenko, Sergey Y

2004-03-15

Side air bags, a relatively new technology designed to protect the head and/or torso in side-impact collisions, are becoming increasingly common in automobiles. Their efficacy in preventing US driver deaths among cars struck on the near (driver's) side was examined using data from the Fatality Analysis Reporting System and the General Estimates System. Risk ratios for driver death per nearside collision during 1999-2001 were computed for head/torso and torso-only side air bags in cars from model years 1997-2002, relative to cars without side air bags. Confounding was addressed by adjusting nearside risk ratios for front- and rear-impact mortality, which is unaffected by side air bags. Risk ratios were 0.55 (95% confidence interval: 0.43, 0.71) for head/torso air bags and 0.89 (95% confidence interval: 0.79, 1.01) for torso-only air bags. Risk was reduced when cars with head/torso air bags were struck by cars/minivans (significant) or pickup trucks/sport utility vehicles (nonsignificant). Risk was reduced in two-vehicle collisions and among male drivers and drivers aged 16-64 years. Protective effects associated with torso-only air bags were observed in single-vehicle crashes and among male and 16- to 64-year-old drivers. Head/torso side air bags appear to be very effective in reducing nearside driver deaths, whereas torso-only air bags appear less protective.

Association of first- and second-generation air bags with front occupant death in car crashes: a matched cohort study.

PubMed

Olson, Carin M; Cummings, Peter; Rivara, Frederick P

2006-07-15

First-generation air bags entail a decreased risk of death for most front seat occupants in car crashes but an increased risk for children. Second-generation air bags were developed to reduce the risks for children, despite the possibility of decreasing protection for others. Using a matched cohort design, the authors estimated risk ratios for death for use of each generation of air bag versus no air bag, adjusted for seat position, restraint use, sex, age, and all vehicle and crash characteristics, among 128,208 automobile occupants involved in fatal crashes on US roadways during 1990-2002. The authors then compared adjusted risk ratios (aRRs) between the two generations of air bags. Among front seat occupants, the aRR for death with a first-generation air bag was 0.90 (95% confidence interval (CI): 0.86, 0.94); the aRR with a second-generation air bag was 0.89 (95% CI: 0.79, 1.00) (p = 0.83 for comparison of aRRs). Among children under age 6 years, the aRR with a first-generation air bag was 1.66 (95% CI: 1.20, 2.30), while the aRR with a second-generation air bag was 1.10 (95% CI: 0.63, 1.93) (p = 0.20 for comparison of aRRs). The differences in aRRs between first- and second-generation air bags among other subgroups were small and not statistically significant.

Using head-on collisions to compare risk of driver death by frontal air bag generation: a matched-pair cohort study.

PubMed

Braver, Elisa R; Kufera, Joseph A; Alexander, Melvin T; Scerbo, Marge; Volpini, Karen; Lloyd, Joseph P

2008-03-01

US air bag regulations were changed in 1997 to allow tests of unbelted male dummies in vehicles mounted and accelerated on sleds, resulting in longer crash pulses than rigid-barrier crashes. This change facilitated depowering of frontal air bags and was intended to reduce air bag-induced deaths. Controversy ensued as to whether sled-certified air bags could increase adult fatality risk. A matched-pair cohort study of two-vehicle, head-on, fatal collisions between drivers involving first-generation versus sled-certified air bags during 1998-2005 was conducted by using Fatality Analysis Reporting System data. Sled certification was ascertained from public information and a survey of automakers. Conditional Poisson regression for matched-pair cohorts was used to estimate risk ratios adjusted for age, seat belt status, vehicle type, passenger car size, and model year for driver deaths in vehicles with sled-certified air bags versus first-generation air bags. For all passenger-vehicle pairs, the adjusted risk ratio was 0.87 (95% confidence interval: 0.77, 0.98). In head-on collisions involving only passenger cars, the adjusted risk ratio was 1.04 (95% confidence interval: 0.85, 1.29). Increased fatality risk for drivers with sled-certified air bags was not observed. A borderline significant interaction between vehicle type and air bag generation suggested that sled-certified air bags may have reduced the risk of dying in head-on collisions among drivers of pickup trucks.

Automobile air bags: friend or foe? A case of air bag-associated ocular trauma and a related literature review.

PubMed

Kenney, Kristin S; Fanciullo, Lisa M

2005-07-01

Although air bags are placed in automobiles to act as safety devices, they have been shown to carry a risk of injury themselves. Ocular injury, in particular, can often be a direct consequence of air bag deployment. A case of ocular air bag injury is presented. A discussion and review of the current literature on this issue follows. A 63-year-old man was transferred to our clinic after sustaining injuries related to a motor vehicle accident, during which the automobile's air bag was deployed. Initial examination revealed many signs of blunt ocular trauma of the O.D., including iridodialysis, dislocated lens with traumatic cataract, and traumatic/inflammatory glaucoma. Initial B-scan showed an attached retina O.D. One month later, the patient underwent an attempted pars plana vitrectomy with lensectomy, iris repair, and insertion of an anterior chamber intraocular lens. Complications arose during the procedure, and a total retinal detachment developed. Resultant acuity is no light perception O.D. Although ocular morbidity can be a direct consequence of air bag deployment, most eye injuries are minimal, and seem to be outweighed by the benefits of air bags. Drivers, as well as passengers, can minimize associated injuries by adhering to specific safety guidelines. This, as well as continual modification and improvement in air bag design, will maximize the safety of air bags and decrease the incidence of vision-threatening ocular injury caused by air bag deployment.

Advanced Air Bag Technology Assessment

NASA Technical Reports Server (NTRS)

Phen, R. L.; Dowdy, M. W.; Ebbeler, D. H.; Kim. E.-H.; Moore, N. R.; VanZandt, T. R.

1998-01-01

As a result of the concern for the growing number of air-bag-induced injuries and fatalities, the administrators of the National Highway Traffic Safety Administration (NHTSA) and the National Aeronautics and Space Administration (NASA) agreed to a cooperative effort that "leverages NHTSA's expertise in motor vehicle safety restraint systems and biomechanics with NASAs position as one of the leaders in advanced technology development... to enable the state of air bag safety technology to advance at a faster pace..." They signed a NASA/NHTSA memorandum of understanding for NASA to "evaluate air bag to assess advanced air bag performance, establish the technological potential for improved technology (smart) air bag systems, and identify key expertise and technology within the agency (i.e., NASA) that can potentially contribute significantly to the improved effectiveness of air bags." NASA is committed to contributing to NHTSAs effort to: (1) understand and define critical parameters affecting air bag performance; (2) systematically assess air bag technology state of the art and its future potential; and (3) identify new concepts for air bag systems. The Jet Propulsion Laboratory (JPL) was selected by NASA to respond to the memorandum of understanding by conducting an advanced air bag technology assessment. JPL analyzed the nature of the need for occupant restraint, how air bags operate alone and with safety belts to provide restraint, and the potential hazards introduced by the technology. This analysis yielded a set of critical parameters for restraint systems. The researchers examined data on the performance of current air bag technology, and searched for and assessed how new technologies could reduce the hazards introduced by air bags while providing the restraint protection that is their primary purpose. The critical parameters which were derived are: (1) the crash severity; (2) the use of seat belts; (3) the physical characteristics of the occupants; (4) the proximity of the occupants to the airbag module; (5) the deployment time, which includes the time to sense the need for deployment, the inflator response parameters, the air bag response, and the reliability of the air bag. The requirements for an advanced air bag technology is discussed. These requirements includes that the system use information related to: (1) the crash severity; (2) the status of belt usage; (3) the occupant category; and (4) the proximity to the air bag to adjust air bag deployment. The parameters for the response of the air bag are: (1) deployment time; (2) inflator parameters; and (3) air bag response and reliability. The state of occupant protection advanced technology is reviewed. This review includes: the current safety restraint systems, and advanced technology characteristics. These characteristics are summarized in a table, which has information regarding the technology item, the potential, and an date of expected utilization. The use of technology and expertise at NASA centers is discussed. NASA expertise relating to sensors, computing, simulation, propellants, propulsion, inflatable systems, systems analysis and engineering is considered most useful. Specific NASA technology developments, which were included in the study are: (1) a capacitive detector; (2) stereoscopic vision system; (3) improved crash sensors; (4) the use of the acoustic signature of the crash to determine crash severity; and (5) the use of radar antenna for pre-crash sensing. Information relating to injury risk assessment is included, as is a summary of the areas of the technology which requires further development.

An overview of frontal air bag performance with changes in frontal crash-test requirements: findings of the Blue Ribbon Panel for the evaluation of advanced technology air bags.

PubMed

Ferguson, Susan A; Schneider, Lawrence W

2008-10-01

In the mid-1990s, evidence emerged that air bag deployments could result in deaths to vulnerable vehicle occupants who were very close to air bag modules when they deployed. In 1997, federal frontal crash test requirements were modified to allow crash testing with unbelted dummies to be performed using sled tests. As a result, vehicle manufacturers were able to redesign air bags to deploy with less force and energy, thereby reducing the toll of air bag-induced deaths. However, there was concern that depowered air bags may not provide the same level of protection to unbelted occupants in severe frontal crashes, particularly occupants of large stature and body mass. This paper provides a summary of recent studies addressing this issue. To expedite the accrual of data regarding air bag performance, the collection of additional crash data was funded by the Alliance of Automobile Manufacturers. A panel of experts was commissioned to oversee the process and evaluate the data. During the past 6 years, a series of studies has been undertaken by panel members and others to evaluate the performance of redesigned air bags and the data are summarized here. There is now convincing evidence that the combination of air bag redesign and public education have resulted in dramatic reductions in air bag-induced infant and child deaths. In addition, the frontal crash fatality risks among children sitting in front seats have been reduced by as much as half, with younger children showing the greatest benefits. Among adult drivers and right-front passengers, there is no evidence for the predicted overall loss of protection with sled-certified air bags and there are far fewer air bag-induced deaths among this population. However, despite exhaustive analyses of frontal-crash data, the possibility of a somewhat elevated fatality risk among a subset of unbelted drivers in sled-certified 1998-1999 model vehicles cannot be ruled out. There also is some evidence that the risks of serious chest injury may be higher among unbelted drivers in frontal crashes in sled-certified vehicles with redesigned air bags. Further research is warranted to determine whether these differences remain in newer model vehicles designed to the advanced air bag rule, which took effect in 2003.

The field performance of frontal air bags: a review of the literature.

PubMed

Kent, Richard; Viano, David C; Crandall, Jeff

2005-03-01

This article presents a broad review of the literature on frontal air bag field performance, starting with the initial government and industry projections of effectiveness and concluding with the most recent assessments of depowered systems. This review includes as many relevant metrics as practicable, interprets the findings, and provides references so the interested reader can further evaluate the limitations, confounders, and utility of each metric. The evaluations presented here range from the very specific (individual case studies) to the general (statistical analyses of large databases). The metrics used to evaluate air bag performance include fatality reduction or increase; serious, moderate, and minor injury reduction or increase; harm reduction or increase; and cost analyses, including insurance costs and the cost of life years saved for various air bag systems and design philosophies. The review begins with the benefits of air bags. Fatality and injury reductions attributable to the air bag are presented. Next, the negative consequences of air bag deployment are described. Injuries to adults and children and the current trends in air bag injury rates are discussed, as are the few documented instances of inadvertent deployments or non-deployment in severe crashes. In the third section, an attempt is made to quantify the influence of the many confounding factors that affect air bag performance. The negative and positive characteristics of air bags are then put into perspective within the context of societal costs and benefits. Finally, some special topics, including risk homeostasis and the performance of face bags, are discussed.

49 CFR 552.12 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... of an air bag system that automatically controls whether or not the air bag deploys during a crash by: (1) Sensing the location of an occupant, moving or still, in relation to the air bag; (2) Interpreting the occupant characteristics and location information to determine whether or not the air bag...

49 CFR 552.12 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... of an air bag system that automatically controls whether or not the air bag deploys during a crash by: (1) Sensing the location of an occupant, moving or still, in relation to the air bag; (2) Interpreting the occupant characteristics and location information to determine whether or not the air bag...

49 CFR 552.12 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of an air bag system that automatically controls whether or not the air bag deploys during a crash by: (1) Sensing the location of an occupant, moving or still, in relation to the air bag; (2) Interpreting the occupant characteristics and location information to determine whether or not the air bag...

49 CFR 552.12 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of an air bag system that automatically controls whether or not the air bag deploys during a crash by: (1) Sensing the location of an occupant, moving or still, in relation to the air bag; (2) Interpreting the occupant characteristics and location information to determine whether or not the air bag...

Sodium azide-associated laryngospasm after air bag deployment.

PubMed

Francis, David; Warren, Samuel A; Warner, Keir J; Harris, William; Copass, Michael K; Bulger, Eileen M

2010-09-01

The advent and incorporation of the air bag into motor vehicles has resulted in the mitigation of many head and truncal injuries in motor vehicle collisions. However, air bag deployment is not risk free. We present a case of sodium azide-induced laryngospasm after air bag deployment. An unrestrained male driver was in a moderate-speed motor vehicle collision with air bag deployment. Medics found him awake, gasping for air with stridorous respirations and guarding his neck. The patient had no external signs of trauma and was presumed to have tracheal injury. The patient was greeted by the Anesthesiology service, which intubated him using glidescope-assisted laryngoscopy. The patient was admitted for overnight observation and treatment of alkaline ocular injury and laryngospasm. Although air bags represent an important advance in automobile safety, their use is not without risk. Bruising and tracheal rupture secondary to air bag deployment have been reported in out-of-position occupants. Additionally, alkaline by-products from the combustion of sodium azide in air bags have been implicated in ocular injury and facial burns. Laryngospasm after sodium azide exposure presents another diagnostic challenge for providers. Therefore, it is incumbent to maintain vigilance in the physical examination and diagnosis of occult injuries after air bag deployment. Copyright © 2010 Elsevier Inc. All rights reserved.

Seat belt use in cars with air bags.

PubMed Central

Williams, A F; Wells, J K; Lund, A K

1990-01-01

Seat belt use was observed in 1,628 cars with air bags and manual belts and 34,223 cars with manual seat belts only. Sixty-six percent of drivers in cars with air bags wore seat belts compared to 63 percent of drivers in cars with manual belts only. The study found no evidence for the speculation that drivers with air bags will reduce their seat belt use because they believe an air bag alone provides sufficient protection. PMID:2240346

Air bag-mediated fatal craniocervical trauma: a case report.

PubMed

Büyük, Yalçin; Uzün, Ibrahim; Erkol, Zerrin; Ağritmiş, Hasan; Ustündağ, Kasim T

2010-07-01

This case report describes a four-year-old girl (102 cm, 17 kg) who sustained fatal craniocerebral injuries as a result of an inflating automobile air bag. The car struck the lid of the sewer system, which was 15 cm above the ground level, at a low speed, and both the driver and passenger air bags inflated. Despite the fact that air bag usage has lessened both the possibility and severity of occupant injuries in frontal collisions, case reports of serious injuries and even deaths especially in children due to air bag deployment, particularly during low speed impacts, highlight the need for changes in both system design and possibly the threshold speed of air bag deployment.

Inadvertent venous air embolism during cesarean section: collapsible intravenous fluid bags without self-sealing outlet have risks. Case report.

PubMed

Bakan, Mefkur; Topuz, Ufuk; Esen, Asim; Basaranoglu, Gokcen; Ozturk, Erdogan

2013-01-01

The anesthesiologist must be aware of the causes, diagnosis and treatment of venous air embolism and adopt the practice patterns to prevent its occurrence. Although venous air embolism is a known complication of cesarean section, we describe an unusual inattention that causes iatrogenic near fatal venous air embolism during a cesarean section under spinal anesthesia. One of the reasons for using self-collapsible intravenous (IV) infusion bags instead of conventional glass or plastic bottles is to take precaution against air embolism. We also demonstrated the risk of air embolism for two kinds of plastic collapsible intravenous fluid bags: polyvinyl chloride (PVC) and polypropylene-based. Fluid bags without self-sealing outlets pose a risk for air embolism if the closed system is broken down, while the flexibility of the bag limits the amount of air entry. PVC-based bags, which have more flexibility, have significantly less risk of air entry when IV administration set is disconnected from the outlet. Using a pressure bag for rapid infusion can be dangerous without checking and emptying all air from the IV bag. 2013 Sociedade Brasileira de Anestesiologia. Published by Elsevier Editora Ltda. All rights reserved.

Inadvertent venous air embolism during cesarean section: Collapsible intravenous fluid bags without self-sealing outlet have risks. Case report.

PubMed

Bakan, Mefkur; Topuz, Ufuk; Esen, Asim; Basaranoglu, Gokcen; Ozturk, Erdogan

2013-01-01

The anesthesiologist must be aware of the causes, diagnosis and treatment of venous air embolism and adopt the practice patterns to prevent its occurrence. Although venous air embolism is a known complication of cesarean section, we describe an unusual inattention that causes iatrogenic near fatal venous air embolism during a cesarean section under spinal anesthesia. One of the reasons for using self-collapsible intravenous (IV) infusion bags instead of conventional glass or plastic bottles is to take precaution against air embolism. We also demonstrated the risk of air embolism for two kinds of plastic collapsible intravenous fluid bags: polyvinyl chloride (PVC) and polypropylene-based. Fluid bags without self-sealing outlets pose a risk for air embolism if the closed system is broken down, while the flexibility of the bag limits the amount of air entry. PVC-based bags, which have more flexibility, have significantly less risk of air entry when IV administration set is disconnected from the outlet. Using a pressure bag for rapid infusion can be dangerous without checking and emptying all air from the IV bag. Copyright © 2013 Sociedade Brasileira de Anestesiologia. Published by Elsevier Editora Ltda. All rights reserved.

75 FR 30900 - Fisker Automotive; Receipt of Application for Temporary Exemption From Advanced Air Bag...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-02

...-0069] Fisker Automotive; Receipt of Application for Temporary Exemption From Advanced Air Bag... temporary exemption from certain advanced air bag requirements of FMVSS No. 208. The basis for the... air bag requirements. Fisker has requested an exemption for the Karma model, and that the exemption...

Air bags alone compared with the combination of mechanical restraints and air bags: implications for the emergency evaluation of crash victims.

PubMed

Sutyak, J P; Passi, V; Hammond, J S

1997-09-01

Air bags (ABs) may be perceived by the public and physicians as protection for thoracoabdominal injuries. This study compares injury patterns when air bags are used alone with injury patterns when air bags plus mechanical restraints (MRs) are used. Patients treated over a 4-year period with emergency medical services-documented AB deployment alone (n = 16) or AB plus MR (n = 22) were identified by trauma registry query. Medical records were reviewed and injuries recorded. Air bag-alone users had more severe overall (injury severity score > or = 15:9 vs 5), chest (abbreviated injury score [AIS] > or = 3:5 vs 1), and abdominal injuries (AIS > or = 3:6 vs 0). They required more tube thoracostomies (5 vs 0) and laparotomies (6 vs 0), longer hospitalizations (11.9 +/- 3.2 vs 5.3 +/- 1.4 days), and more intensive care unit admissions (8 vs 1). Craniofacial injuries (AIS > or = 3:6 vs 6) and fractures were similar. More victims using air bags alone required impatient rehabilitation and some patients died (6 vs 1). Crash victims using air bags alone (vs AB plus MR) had increased injury severity, hospitalizations, thoracoabdominal procedures, and rehabilitation. Physicians must be aware of the incomplete protection by air bags alone.

The cost-effectiveness of air bags by seating position.

PubMed

Graham, J D; Thompson, K M; Goldie, S J; Segui-Gomez, M; Weinstein, M C

1997-11-05

Motor vehicle crashes continue to cause significant mortality and morbidity in the United States. Installation of air bags in new passenger vehicles is a major initiative in the field of injury prevention. To assess the net health consequences and cost-effectiveness of driver's side and front passenger air bags from a societal perspective, taking into account the increased risk to children who occupy the front passenger seat and the diminished effectiveness for older adults. A deterministic state transition model tracked a hypothetical cohort of new vehicles over a 20-year period for 3 strategies: (1) installation of safety belts, (2) installation of driver's side air bags in addition to safety belts, and (3) installation of front passenger air bags in addition to safety belts and driver's side air bags. Changes in health outcomes, valued in terms of quality-adjusted life-years (QALYs) and costs (in 1993 dollars), were projected following the recommendations of the Panel on Cost-effectiveness in Health and Medicine. US population-based and convenience sample data were used. Incremental cost-effectiveness ratios. Safety belts are cost saving, even at 50% use. The addition of driver's side air bags to safety belts results in net health benefits at an incremental cost of $24000 per QALY saved. The further addition of front passenger air bags results in an incremental net benefit at a higher incremental cost of $61000 per QALY saved. Results were sensitive to the unit cost of air bag systems, their effectiveness, baseline fatality rates, the ratio of injuries to fatalities, and the real discount rate. Both air bag systems save life-years at costs that are comparable to many medical and public health practices. Immediate steps can be taken to enhance the cost-effectiveness of front passenger air bags, such as moving children to the rear seat.

77 FR 39564 - Group Lotus Plc, Receipt of Petition for Temporary Exemption From an Advanced Air Bag Requirement...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-03

... went into effect, low volume manufacturers now have access to advanced air bag technology. Accordingly, NHTSA has concluded that the expense of advanced air bag technology is not now sufficient, in and of...-0086] Group Lotus Plc, Receipt of Petition for Temporary Exemption From an Advanced Air Bag Requirement...

78 FR 15114 - Group Lotus plc; Grant of Petition for a Temporary Exemption From an Advanced Air Bag Requirement...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-08

... went into effect, low volume manufacturers now have access to advanced air bag technology. Accordingly, NHTSA has concluded that the expense of advanced air bag technology is not now sufficient, in and of... into effect, low volume manufacturers now have access to advanced air bag technology.\\14\\ Accordingly...

77 FR 52619 - Make Inoperative Exemptions; Retrofit On-Off Switches for Air Bags

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-30

... improved frontal crash protection for all occupants, by means that include advanced air bag technology. In... of advanced air bag technology and the retrofit switch brochures and forms that were included in Part.... We will also reexamine the at-risk groups in light of advanced air bag technology, the brochures and...

Air bags and children: a potentially lethal combination.

PubMed

McCaffrey, M; German, A; Lalonde, F; Letts, M

1999-01-01

Air bags have been responsible for saving thousands of lives since their introduction in the early 1970s. Now, however, it has become apparent that under certain conditions, these restraint mechanisms designed to save lives have in fact been the cause of needless morbidity and mortality in children. We reviewed 13 children injured by air bags in Canada, where seat belt wear is mandatory for all occupants. Although 12 of the children sustained relatively minor air bag trauma, one child was killed by the air bag deployment, sustaining an occipital-C1 dislocation. The pediatric population is at particular risk as many parents continue to unwittingly place their children in the front seat and thus in jeopardy of sustaining air bag-induced injuries should a collision occur.

Vehicle safety : technologies, challenges, and research and development expenditures for advanced air bags

DOT National Transportation Integrated Search

2001-06-01

One hundred seventy five fatalities - primarily children and small women - have been attributed to the deployment of an air bag in relatively low-speed crashes as of April 2001. Advanced air bag systems tailor the deployment of the bags to the charac...

Association of driver air bags with driver fatality: a matched cohort study.

PubMed

Cummings, Peter; McKnight, Barbara; Rivara, Frederick P; Grossman, David C

2002-05-11

To estimate the association of driver air bag presence with driver fatality in road traffic crashes. Matched pair cohort study. All passenger vehicle crashes in the United States during 1990-2000 inclusive. 51 031 driver-passenger pairs in the same vehicle. Relative risk of death within 30 days of a crash. Drivers with an air bag were less likely to die than drivers without an air bag (adjusted relative risk 0.92 (95% confidence interval 0.88 to 0.96)). This estimate was nearly the same whether drivers wore a seat belt (adjusted relative risk 0.93) or not (0.91). Air bags were associated with more protection for women (0.88 (0.82 to 0.93)), than for men (0.94 (0.90 to 0.99)). Drivers wearing a seat belt were less likely to die than unbelted drivers (0.35 (0.33 to 0.36)). Belted drivers with an air bag were less likely to die than unbelted drivers without an air bag (0.32 (0.30 to 0.34)). If the associations are causal the average risk of driver death was reduced 8% (95% confidence interval 4% to 12%) by an air bag. Benefit was similar for belted and unbelted drivers and was slightly greater for women. However, seat belts offered much more protection than air bags.

The effect of frontal air bags on eye injury patterns in automobile crashes.

PubMed

Duma, Stefan M; Jernigan, M Virginia; Stitzel, Joel D; Herring, Ian P; Crowley, John S; Brozoski, Fred T; Bass, Cameron R

2002-11-01

To investigate eye injuries resulting from frontal automobile crashes and to determine the effects of frontal air bags. The National Automotive Sampling System database files from January 1, 1993, through December 31, 1999, were examined in a 3-part study that included an investigation of 22 236 individual crashes that occurred in the United States. A new 4-level eye injury severity scale that quantifies injuries based on recovery time, need for surgery, and possible loss of sight was developed. Of all occupants who were exposed to an air bag deployment, 3% sustained an eye injury. In contrast, 2% of occupants not exposed to an air bag deployment sustained an eye injury. A closer examination of the type of eye injuries showed that there was a statistically significant increase in the risk of corneal abrasions for occupants who were exposed to an air bag compared with those who were not (P =.03). Of occupants exposed to an air bag deployment, 0.5% sustained a corneal abrasion compared with 0.04% of occupants who were not exposed to an air bag. Using the new injury levels, it was shown that although occupants exposed to an air bag deployment had a higher risk of sustaining minor eye injuries, the air bag appears to have provided a beneficial exchange by reducing the number of severe eye injuries.

75 FR 9633 - Reports, Forms and Record Keeping Requirements; Agency Information Collection Activity Under OMB...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-03

... Administration Title: Part 585--Advanced Air Bag Phase-In Reporting Requirements. OMB Number: 2127-0599. Type of... requirements of this FMVSS related to the implementation of advanced air bags. Phase 1 of the advanced air bag... advanced air bag phase-in begins September 1, 2007 with 100 percent compliance by September 1, 2009. Phase...

Automobile driver fatalities in frontal impacts: air bags compared with manual belts.

PubMed Central

Zador, P L; Ciccone, M A

1993-01-01

OBJECTIVES. The effectiveness of air bags was estimated in this study by comparing driver fatalities in frontal crashes with driver fatalities in nonfrontal crashes, for cars with air bags and manual belts and cars with manual belts only. METHODS. Fatal Accident Reporting System data for drivers fatally injured during 1985 to 1991 in 1985 to 1991 model year cars that were equipped with air bags in or before model year 1991 were analyzed. RESULTS. Driver fatalities in frontal crashes in air bag cars were 28% lower than those in comparable cars with manual belts only. This percentage was used for estimating the overall fatality reduction in air bag cars. The reduction was greater in large cars (50%) than in midsize cars (19%) or in small cars (14%). Air bags reduced driver fatalities in frontal crashes involving ejection by about 9%. Fatalities in frontal crashes among drivers who were reportedly using manual belts at the time of the crash were reduced by about 15%. The comparable reduction among drivers who were reportedly not using manual belts was 31%. CONCLUSION. It was estimated that air bags reduced the total number of all driver fatalities by about 19%. PMID:8484445

49 CFR 563.7 - Data elements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... cycle, download At time of download 3 N/A Safety belt status, driver −1.0 sec N/A Frontal air bag warning lamp, on/off 2 −1.0 sec N/A Frontal air bag deployment, time to deploy, in the case of a single stage air bag, or time to first stage deployment, in the case of a multi-stage air bag, driver Event N/A...

49 CFR 563.7 - Data elements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... cycle, download At time of download 3 N/A Safety belt status, driver −1.0 sec N/A Frontal air bag warning lamp, on/off 2 −1.0 sec N/A Frontal air bag deployment, time to deploy, in the case of a single stage air bag, or time to first stage deployment, in the case of a multi-stage air bag, driver Event N/A...

49 CFR 563.7 - Data elements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... cycle, download At time of download 3 N/A Safety belt status, driver −1.0 sec N/A Frontal air bag warning lamp, on/off 2 −1.0 sec N/A Frontal air bag deployment, time to deploy, in the case of a single stage air bag, or time to first stage deployment, in the case of a multi-stage air bag, driver Event N/A...

Association of driver air bags with driver fatality: a matched cohort study

PubMed Central

Cummings, Peter; McKnight, Barbara; Rivara, Frederick P; Grossman, David C

2002-01-01

Objective To estimate the association of driver air bag presence with driver fatality in road traffic crashes. Design Matched pair cohort study. Setting All passenger vehicle crashes in the United States during 1990-2000 inclusive. Subjects 51 031 driver-passenger pairs in the same vehicle. Main outcome measures Relative risk of death within 30 days of a crash. Results Drivers with an air bag were less likely to die than drivers without an air bag (adjusted relative risk 0.92 (95% confidence interval 0.88 to 0.96)). This estimate was nearly the same whether drivers wore a seat belt (adjusted relative risk 0.93) or not (0.91). Air bags were associated with more protection for women (0.88 (0.82 to 0.93)), than for men (0.94 (0.90 to 0.99)). Drivers wearing a seat belt were less likely to die than unbelted drivers (0.35 (0.33 to 0.36)). Belted drivers with an air bag were less likely to die than unbelted drivers without an air bag (0.32 (0.30 to 0.34)). Conclusions If the associations are causal the average risk of driver death was reduced 8% (95% confidence interval 4% to 12%) by an air bag. Benefit was similar for belted and unbelted drivers and was slightly greater for women. However, seat belts offered much more protection than air bags. What is already known on this topicStudies have estimated that driver air bags reduce the risk of death in a road vehicle crash by 10-14%These studies disagree as to whether benefit is greater for drivers wearing a seat belt or for unbelted driversWhat this study addsHaving an air bag was associated with an 8% reduction in the risk of death, whether the driver was belted or notThe reduction in risk was greater for women (12%) than for men (6%)Seat belts provided much greater protection, with seat belt use reducing the risk of death by 65% (or by 68% in combination with an air bag) PMID:12003882

Front air bag nondeployments in frontal crashes fatal to drivers or right-front passengers.

PubMed

Braver, Elisa R; McCartt, Anne T; Sherwood, Christopher P; Zuby, David S; Blanar, Laura; Scerbo, Marge

2010-04-01

Public concern has arisen about the reliability of front air bags because Fatality Analysis Reporting System (FARS) data indicate many nondeployed air bags in fatal frontal crashes. However, the accuracy of air bag deployment, the variable in question, is uncertain. This study aimed to provide more certain estimates of nondeployment incidence in fatal frontal crashes. Fatally injured passenger vehicle drivers and right-front passengers in frontal crashes were identified in two U.S. databases for calendar years 1998-2006 and model years 1994-2006: FARS, a census of police-reported fatal crashes on public roads, and National Automotive Sampling System/Crashworthiness Data System (NASS/CDS), a probability sample of tow-away crashes. NASS/CDS contains subsets of fatal crashes in FARS and collects detailed data using crash investigators. Front air bag deployment coding for front-seat occupant fatalities was compared in FARS and NASS/CDS, and case reviews were conducted. Among FARS frontal deaths with available deployment status (N = 43,169), front air bags were coded as not deployed for 18 percent of front occupants. In comparison, NASS/CDS (N = 628) reported 9 percent (weighted estimate) nondeployment among front occupants killed. Among crashes common to both databases, NASS/CDS reported deployments for 45 percent of front occupant deaths for which FARS had coded nondeployments. Detailed case reviews of NASS/CDS crashes indicated highly accurate coding for deployment status. Based on this case review, 8 percent (weighted estimate) of front occupant deaths in frontal crashes appeared to involve air bag nondeployments; 1-2 percent of front occupant deaths represented potential system failures where deployments would have been expected. Air bag deployments appeared unwarranted in most nondeployments based on crash characteristics. FARS data overstate the magnitude of the problem of air bag deployment failures; steps should be taken to improve coding. There are inherent uncertainties in judgments about whether or not air bags would be expected to deploy in some crashes. Continued monitoring of air bag performance is warranted.

49 CFR 172.101 - Purpose and use of hazardous materials table.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Forbidden Forbidden A 48, 87, 126 I Air bag inflators, or Air bag modules, or Seat-belt pretensioners. 1.4G UN0503 II 1.4G 161 None 62 None Forbidden 75 kg 02 Air bag inflators, or Air bag modules, or Seat-belt pretensioners. 9 UN3268 III 9 160 166 166 166 25 kg 100 kg A Air, compressed 2.2 UN1002 2.2 78 306, 307 302 302...

14 CFR 223.24 - Transportation of empty mail bags.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Transportation of empty mail bags. Any carrier authorized to engage in foreign air transportation may transport in foreign air transportation empty air mail bags from any country to the country of origin of such... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Transportation of empty mail bags. 223.24...

14 CFR 223.24 - Transportation of empty mail bags.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Transportation of empty mail bags. Any carrier authorized to engage in foreign air transportation may transport in foreign air transportation empty air mail bags from any country to the country of origin of such... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Transportation of empty mail bags. 223.24...

14 CFR 223.24 - Transportation of empty mail bags.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Transportation of empty mail bags. Any carrier authorized to engage in foreign air transportation may transport in foreign air transportation empty air mail bags from any country to the country of origin of such... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Transportation of empty mail bags. 223.24...

42 CFR 84.88 - Breathing bag test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Apparatus § 84.88 Breathing bag test. (a) Breathing bags will be tested in an air atmosphere saturated with... Institute upon request. (d) The air within the bag(s) shall not contain more than 100 parts per million of... 42 Public Health 1 2014-10-01 2014-10-01 false Breathing bag test. 84.88 Section 84.88 Public...

Air bag restraint device

DOEpatents

Marts, Donna J.; Richardson, John G.

1995-01-01

A rear-seat air bag restraint device is disclosed that prevents an individual, or individuals, from continuing violent actions while being transported in a patrol vehicle's rear seat without requiring immediate physical contact by the law enforcement officer. The air bag is activated by a control switch in the front seat and inflates to independently restrict the amount of physical activity occurring in the rear seat of the vehicle while allowing the officer to safely stop the vehicle. The air bag can also provide the officer additional time to get backup personnel to aid him if the situation warrants it. The bag is inflated and maintains a constant pressure by an air pump.

A One-Piece Lunar Regolith Bag Garage Prototype

NASA Technical Reports Server (NTRS)

Smithers, G. A.; Nehls, M. K.; Hovater, M. A.; Evans, S. W.; Miller, J. S.; Broughton, R. M., Jr.; Beale, D.; Kilinc-Balci, F.

2007-01-01

Shelter structures on the moon, even in early phases of exploration, should incorporate lunar materials as much as possible. This Technical Memorandum details the design and construction of a prototype for a one-piece regolith bag unpressurized garage concept and a materials testing program to investigate six candidate fabrics to learn how they might perform in the lunar environment. The conceptualization was that a lightweight fabric form be launched from Earth and landed on the lunar surface to be robotically filled with raw lunar regolith. Regolith bag fabric candidates included: Vectran(TM), Nextel(TM), Gore PTFE Fabric(TM), Zylon(TM), Twaron(TM), and Nomex(TM). Tensile (including post radiation exposure), fold, abrasion, and hypervelocity impact testing were performed under ambient conditions, and also performed under cold and elevated temperatures. In some cases, Johnson Space Center lunar simulant (JSC-1) was used in conjunction with testing. A series of preliminary structures was constructed during final prototype design based on the principles of the classic masonry arch. The prototype was constructed of Kevlar(TM) and filled with vermiculite. The structure is free-standing, but has not yet been load tested. Future plans would be to construct higher fidelity prototypes and to conduct appropriate tests of the structure.

Effect of vehicle type on the performance of second generation air bags for child occupants.

PubMed

Arbogast, Kristy B; Durbin, Dennis R; Kallan, Michael J; Winston, Flaura K

2003-01-01

Passenger air bags experienced considerable design modification in the late 1990s, principally to mitigate risks to child passengers. This study utilized Data from the Partners for Child Passenger Safety study, a large-scale child-focused crash surveillance system, to examine the effect of vehicle type on the differential performance of first and second generation air bags on injuries to restrained children in frontal impact crashes. Our results show that the benefit of second-generation air bags was seen in passenger cars - those children exposed to second-generation air bags were half as likely to sustain a serious injury - and minivans. However, in SUVs the data suggest no reduction in injury risk with the new designs. This field data provides crucial real-world experience to the automotive industry as they work towards the next generation of air bag designs.

Effect of Vehicle type on the Performance of Second Generation Air Bags for Child Occupants

PubMed Central

Arbogast, Kristy B.; Durbin, Dennis R.; Kallan, Michael J.; Winston, Flaura K.

2003-01-01

Passenger air bags experienced considerable design modification in the late 1990s, principally to mitigate risks to child passengers. This study utilized Data from the Partners for Child Passenger Safety study, a large-scale child-focused crash surveillance system, to examine the effect of vehicle type on the differential performance of first and second generation air bags on injuries to restrained children in frontal impact crashes. Our results show that the benefit of second-generation air bags was seen in passenger cars – those children exposed to second-generation air bags were half as likely to sustain a serious injury – and minivans. However, in SUVs the data suggest no reduction in injury risk with the new designs. This field data provides crucial real-world experience to the automotive industry as they work towards the next generation of air bag designs. PMID:12941218

Deaths among drivers and right-front passengers in frontal collisions: redesigned air bags relative to first-generation air bags.

PubMed

Braver, Elisa R; Scerbo, Marge; Kufera, Joseph A; Alexander, Melvin T; Volpini, Karen; Lloyd, Joseph P

2008-03-01

After automakers were allowed the option of using sled tests for unbelted male dummies to certify the frontal crash performance of vehicles, most frontal air bags were depowered, starting in model year 1998, to reduce deaths and serious injuries arising from air bag deployments. Concern has been expressed that depowering air bags could compromise the protection of adult occupants. This study aimed to determine the effects of changes in air bag designs on risk of death among front-seat occupants. Deaths among drivers and right-front passengers per involvement in frontal police-reported crashes during calendar years 1998-2004 were compared among vehicles with sled-certified air bags (model years 1998-2004) and first-generation air bags (model years 1994-97). Frontal crash deaths were identified from the Fatality Analysis Reporting System. National estimates of police-reported crashes were derived from the National Automotive Sampling System/General Estimates System. Sled certification status for model years 1998-2004 was ascertained from published federal data and a survey of automobile manufacturers. Passenger cars, pickup trucks, sport utility vehicles, and minivans were studied. Stratified analyses were done to compute risk ratios (RR) and 95% confidence intervals (95% CI) for driver and right-front passenger deaths by air bag generation and crash, vehicle, and driver characteristics. In frontal crashes, overall RRs were 0.89 for driver deaths (95% CI = 0.74-1.08) and 0.89 for right-front passenger deaths (95% CI = 0.74-1.07) in sled-certified vehicles compared with first-generation air bag-equipped vehicles. Child right-front passengers (ages 0-4, 5-9) in vehicles with sled-certified air bags had statistically significant reductions in risk of dying in frontal collisions, including a 65% reduced risk among ages 0-4 (RR = 0.35; 95% CI = 0.21-0.60). No differences in effects of sled-certified air bags were observed between drivers ages 15-59 and 60-74 in sled-certified vehicles, both of whom had RRs slightly below 0.90 (non-significant). Among occupants killed in sled-certified vehicles, police-reported belt use was somewhat higher than in first-generation vehicles. No differences in risk of frontal crash deaths were observed between adult occupants with sled-certified and first-generation air bags. Consistent with reports of decreases in air bag-related deaths, this study observed significant reductions in frontal deaths among child passengers seated in the right-front position in sled-certified vehicles. Higher restraint use rates among children in sled-certified vehicles and other vehicle design changes might have contributed partially to these reductions.

Air bags and the skin.

PubMed

Corazza, Monica; Trincone, Silvana; Zampino, Maria Rosaria; Virgili, Annarosa

2004-01-01

Air bags, fitted in the majority of new automobiles, are safety devices activated when a sudden deceleration causes the ignition of a propellant cartridge containing sodium azide. The bag is inflated by nitrogen liberated during the combustion. Deployment releases various high-temperature gases, including nitrogen and carbon dioxide, and produces sodium hydroxide, a highly irritant alkaline substance. In about 7%-8% of cases, air bags cause dermatologic injuries such as traumatic lesions, irritant dermatitis, and chemical and thermal burns. Nondermatologic lesions, such as ocular damage (alkali keratitis, corneal abrasions), ear lesions, bone fractures, and contusive damage can also be caused by air bag deployment.

Air bag restraint device

DOEpatents

Marts, D.J.; Richardson, J.G.

1995-10-17

A rear-seat air bag restraint device is disclosed that prevents an individual, or individuals, from continuing violent actions while being transported in a patrol vehicle`s rear seat without requiring immediate physical contact by the law enforcement officer. The air bag is activated by a control switch in the front seat and inflates to independently restrict the amount of physical activity occurring in the rear seat of the vehicle while allowing the officer to safely stop the vehicle. The air bag can also provide the officer additional time to get backup personnel to aid him if the situation warrants it. The bag is inflated and maintains a constant pressure by an air pump. 8 figs.

Preliminary evaluation of advanced air bag field performance using event data recorders

DOT National Transportation Integrated Search

2008-08-31

This report describes a preliminary evaluation of the field performance of occupant restraint systems designed with advanced air bag features including those specified in the Federal Motor Vehicle Safety Standard No. 208 for advanced air bags, throug...

Driver air bag effectiveness by severity of the crash.

PubMed Central

Segui-Gomez, M

2000-01-01

OBJECTIVES: This analysis provided effectiveness estimates of the driver-side air bag while controlling for severity of the crash and other potential confounders. METHODS: Data were from the National Automotive Sampling System (1993-1996). Injury severity was described on the basis of the Abbreviated Injury Scale, Injury Severity Score, Functional Capacity Index, and survival. Ordinal, linear, and logistic multivariate regression methods were used. RESULTS: Air bag deployment in frontal or near-frontal crashes decreases the probability of having severe and fatal injuries (e.g., Abbreviated Injury Scale score of 4-6), including those causing a long-lasting high degree of functional limitation. However, air bag deployment in low-severity crashes increases the probability that a driver (particularly a woman) will sustain injuries of Abbreviated Injury Scale level 1 to 3. Air bag deployment exerts a net injurious effect in low-severity crashes and a net protective effect in high-severity crashes. The level of crash severity at which air bags are protective is higher for female than for male drivers. CONCLUSIONS: Air bag improvement should minimize the injuries induced by their deployment. One possibility is to raise their deployment level so that they deploy only in more severe crashes. PMID:11029991

Staying Safe in the Car and on the Bus

MedlinePlus

... dangerous and everyone could get hurt. What About Air Bags? You might know a little bit about air bags because many car commercials on TV talk about them. If a car with air bags is in a front-end accident, the ...

Vehicle safety : technologies, challenges, and research development expenditures for advanced air bags

DOT National Transportation Integrated Search

2001-06-01

Some advanced air bag technologies are currently being installed in vehicles and others are still being developed. The principal advanced technology that is currently being installed in some vehicles is air bags that can inflate with lower or higher ...

Vented spikes improve delivery from intravenous bags with no air headspace.

PubMed

Galush, William J; Horst, Travis A

2015-07-01

Flexible plastic bags are the container of choice for most intravenous (i.v.) infusions. Under certain circumstances, however, the air-liquid interface present in these i.v. bags can lead to physical instability of protein biopharmaceuticals, resulting in product aggregation. In principle, the air headspace present in the bags can be removed to increase drug stability, but experiments described here show that this can result in incomplete draining of solution from the bag using gravity delivery, or generation of negative pressure in the bag when an infusion pump is used. It is expected that these issues could lead to incomplete delivery of medication to patients or pump-related problems, respectively. However, here it is shown that contrary to the standard pharmacy practice of using nonvented spikes with i.v. bags, the use of vented spikes with i.v. bags that lack air headspace allows complete delivery of the dose solution without impacting the physical stability of a protein-based drug. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Fatality Reduction by Air Bags: Analyses of Accident Data through Early 1996

DOT National Transportation Integrated Search

1996-08-01

The fatality risk of front-seat occupants of passenger cars and light trucks equipped with air bags is compared to the corresponding risk in similar vehicles without air bags, based on statistical analysis of Fatal Accident Reporting System (FARS)dat...

49 CFR 585.15 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase... any of those production years as complying with phase one of the advanced air bag requirements of... manufactured during that production year as complying with phase two of the advanced air bag requirements of...

49 CFR 585.15 - Reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase... any of those production years as complying with phase one of the advanced air bag requirements of... manufactured during that production year as complying with phase two of the advanced air bag requirements of...

49 CFR 585.15 - Reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase... any of those production years as complying with phase one of the advanced air bag requirements of... manufactured during that production year as complying with phase two of the advanced air bag requirements of...

Air Bag Applies Uniform Bonding Pressure

NASA Technical Reports Server (NTRS)

Gillespie, C. A.

1982-01-01

Air-bag box applies constant uniform pressure to tiles and other objects undergoing adhesive bonding. Box is basically a compliant clamp with adjustable force and position. Can be used on irregular surfaces as well as on flat ones. Pressurized air is fed to bag through a tube so that it expands, filling the box and pressing against work. Bag adopts a contour that accommodates surface under open side of box.

Proceedings of the National Transportation Safety Board Public Forum on Air Bags and Child Passenger Safety

DOT National Transportation Integrated Search

1997-01-01

The National Transportation Safety Board convened a 4-day public forum from March 17 to March 20, 1997, to discuss concerns related to the effectiveness of air bags, passenger vulnerability to injuries from air bag deployment, other countries' experi...

The Application of Advanced Technology to Improve Air Bag Performance

NASA Technical Reports Server (NTRS)

Phen, R.; Dowdy, M.; Ebbeler, D.; Kim, E.; Moore, N.; Van Zandt, T.

1998-01-01

In December 1996 the National Highway Traffic Safety Administration (NHTSA) and the National Aeronautics and Space Administration (NASA) signed a memorandum of understanding for NASA to assess the capability of advanced technology to reduce air bag inflation-induced injuries and increase air bag effectiveness.

Surface pre-conditioning with bioactive glass air-abrasion can enhance enamel white spot lesion remineralization.

PubMed

Milly, Hussam; Festy, Frederic; Andiappan, Manoharan; Watson, Timothy F; Thompson, Ian; Banerjee, Avijit

2015-05-01

To evaluate the effect of pre-conditioning enamel white spot lesion (WSL) surfaces using bioactive glass (BAG) air-abrasion prior to remineralization therapy. Ninety human enamel samples with artificial WSLs were assigned to three WSL surface pre-conditioning groups (n=30): (a) air-abrasion with BAG-polyacrylic acid (PAA-BAG) powder, (b) acid-etching using 37% phosphoric acid gel (positive control) and (c) unconditioned (negative control). Each group was further divided into three subgroups according to the following remineralization therapy (n=10): (I) BAG paste (36 wt.% BAG), (II) BAG slurry (100 wt.% BAG) and (III) de-ionized water (negative control). The average surface roughness and the lesion step height compared to intra-specimen sound enamel reference points were analyzed using non-contact profilometry. Optical changes within the lesion subsurface compared to baseline scans were assessed using optical coherence tomography (OCT). Knoop microhardness evaluated the WSLs' mechanical properties. Raman micro-spectroscopy measured the v-(CO3)(2-)/v1-(PO4)(3-) ratio. Structural changes in the lesion were observed using confocal laser scanning microscopy (CLSM) and scanning electron microscopy-energy dispersive X-ray spectrometry (SEM-EDX). All comparisons were considered statistically significant if p<0.05. PAA-BAG air-abrasion removed 5.1 ± 0.6 μm from the lesion surface, increasing the WSL surface roughness. Pre-conditioning WSL surfaces with PAA-BAG air-abrasion reduced subsurface light scattering, increased the Knoop microhardness and the mineral content of the remineralized lesions (p<0.05). SEM-EDX revealed mineral depositions covering the lesion surface. BAG slurry resulted in a superior remineralization outcome, when compared to BAG paste. Pre-conditioning WSL surfaces with PAA-BAG air-abrasion modified the lesion surface physically and enhanced remineralization using BAG 45S5 therapy. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

49 CFR 563.9 - Data capture.

Code of Federal Regulations, 2013 CFR

2013-10-01

... frontal air bag deployment crash, capture and record the current deployment data. In a side or side curtain/tube air bag deployment crash, where lateral delta-V is recorded by the EDR, capture and record the current deployment data. The memory for the air bag deployment event must be locked to prevent any...

49 CFR 585.14 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting Requirements § 585.14 Definitions. For the purposes of this subpart, (a) Phase one of the advanced air bag....208. (b) Phase two of the advanced air bag reporting requirements of Standard No. 208 refers to the...

49 CFR 563.9 - Data capture.

Code of Federal Regulations, 2014 CFR

2014-10-01

... frontal air bag deployment crash, capture and record the current deployment data. In a side or side curtain/tube air bag deployment crash, where lateral delta-V is recorded by the EDR, capture and record the current deployment data. The memory for the air bag deployment event must be locked to prevent any...

49 CFR 595.5 - Requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) MAKE INOPERATIVE EXEMPTIONS Retrofit On-Off Switches for Air Bags... an occupant of the vehicle to turn off an air bag in that vehicle, subject to the conditions in... Administration that authorizes the installation of an on-off switch in that vehicle for that air bag and includes...

49 CFR 595.5 - Requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) MAKE INOPERATIVE EXEMPTIONS Retrofit On-Off Switches for Air Bags... an occupant of the vehicle to turn off an air bag in that vehicle, subject to the conditions in... Administration that authorizes the installation of an on-off switch in that vehicle for that air bag and includes...

49 CFR 585.14 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting Requirements § 585.14 Definitions. For the purposes of this subpart, (a) Phase one of the advanced air bag....208. (b) Phase two of the advanced air bag reporting requirements of Standard No. 208 refers to the...

49 CFR 585.14 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting Requirements § 585.14 Definitions. For the purposes of this subpart, (a) Phase one of the advanced air bag....208. (b) Phase two of the advanced air bag reporting requirements of Standard No. 208 refers to the...

49 CFR 585.14 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting Requirements § 585.14 Definitions. For the purposes of this subpart, (a) Phase one of the advanced air bag....208. (b) Phase two of the advanced air bag reporting requirements of Standard No. 208 refers to the...

49 CFR 595.5 - Requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) MAKE INOPERATIVE EXEMPTIONS Retrofit On-Off Switches for Air Bags... an occupant of the vehicle to turn off an air bag in that vehicle, subject to the conditions in... Administration that authorizes the installation of an on-off switch in that vehicle for that air bag and includes...

49 CFR 585.14 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting Requirements § 585.14 Definitions. For the purposes of this subpart, (a) Phase one of the advanced air bag....208. (b) Phase two of the advanced air bag reporting requirements of Standard No. 208 refers to the...

49 CFR 563.9 - Data capture.

Code of Federal Regulations, 2012 CFR

2012-10-01

... frontal air bag deployment crash, capture and record the current deployment data. In a side or side curtain/tube air bag deployment crash, where lateral delta-V is recorded by the EDR, capture and record the current deployment data. The memory for the air bag deployment event must be locked to prevent any...

Ocular alkali burn associated with automobile air-bag activation.

PubMed Central

White, J E; McClafferty, K; Orton, R B; Tokarewicz, A C; Nowak, E S

1995-01-01

Alkali burns of the eye can result in permanent visual impairment and are therefore potentially devastating. Immedicate diagnosis and treatment are essential to a good prognosis. The authors report the case of a 52-year-old woman who suffered alkali keratitis as the result of the activation of an automobile air bag. This type of injury will be seen more frequently as more cars are equipped with air bags and should be suspected in drivers and passengers involved in accidents in which air bags have been activated. PMID:7553495

76 FR 33402 - Tesla Motors, Inc.; Receipt of Petition for Renewal of Temporary Exemption from the Advanced Air...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-08

... manufacturers now have access to advanced air bag technology. Accordingly, NHTSA tentatively concludes that the expense of advanced air bag technology is not now sufficient, in and of itself, to justify the grant of a... the agency for renewal of a temporary exemption from certain advanced air bag requirements of FMVSS No...

49 CFR 176.405 - Stowage of charcoal.

Code of Federal Regulations, 2013 CFR

2013-10-01

... bags and offered for transportation on board a vessel in a quantity over 1016 kg (2240 pounds) must be loaded so that the bags are laid horizontally and stacked with space for efficient air circulation. If... repaired bags restowed. (d) Charcoal “screenings” packed in bags must be stowed to provide spaces for air...

49 CFR 176.405 - Stowage of charcoal.

Code of Federal Regulations, 2014 CFR

2014-10-01

... bags and offered for transportation on board a vessel in a quantity over 1016 kg (2240 pounds) must be loaded so that the bags are laid horizontally and stacked with space for efficient air circulation. If... repaired bags restowed. (d) Charcoal “screenings” packed in bags must be stowed to provide spaces for air...

49 CFR 176.405 - Stowage of charcoal.

Code of Federal Regulations, 2012 CFR

2012-10-01

... bags and offered for transportation on board a vessel in a quantity over 1016 kg (2240 pounds) must be loaded so that the bags are laid horizontally and stacked with space for efficient air circulation. If... repaired bags restowed. (d) Charcoal “screenings” packed in bags must be stowed to provide spaces for air...

76 FR 19179 - Spyker Automobielen B.V.; Receipt of Application for Extension of Temporary Exemption From...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-06

... went into effect, low volume manufacturers now have access to advanced air bag technology. Accordingly, NHTSA tentatively concludes that the expense of advanced air bag technology may not now be sufficient...) has applied for an extension of a previously granted temporary exemption from certain advanced air bag...

78 FR 11271 - Reports, Forms, and Record keeping Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-15

... following proposed collections of information: Title: Air Bag Deactivation. OMB Control Number: 2127-0588.... Abstract: If a private individual or lessee wants to install an air bag on-off switch to turn-off either or both frontal air bags, they must complete Form OMB 2127-0588 to certify certain statements regarding...

78 FR 38095 - Request for Comments of a Previously Approved Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-25

.... Mrs. Ball's telephone number is (202) 366-2245. SUPPLEMENTARY INFORMATION: Title: Air Bag Deactivation... vehicle dealers, repair business. Abstract: If a private individual or lessee wants to install an air bag on-off switch to turn-off either or both frontal air bags, they must complete Form OMB 2127-0588 to...

75 FR 80109 - Nissan North America, Inc., Receipt of Petition for Decision of Inconsequential Noncompliance

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-21

... light whenever the passenger air bag system is deactivated and does not emit light whenever the passenger air bag system is activated, except that the telltale(s) need not illuminate when the passenger seat is unoccupied. Each telltale:* * * (b) Shall have the identifying words ``PASSENGER AIR BAG OFF...

Wave energy absorption by a floating air bag

NASA Astrophysics Data System (ADS)

Kurniawan, A.; Chaplin, J. R.; Greaves, D. M.; Hann, M.

2017-02-01

A floating air bag, ballasted in water, expands and contracts as it heaves under wave action. Connecting the bag to a secondary volume via a turbine transforms the bag into a device capable of generating useful energy from the waves. Small-scale measurements of the device reveal some interesting properties, which are successfully predicted numerically. Owing to its compressibility, the device can have a heave resonance period longer than that of a rigid device of the same shape and size, without any phase control. Furthermore, varying the amount of air in the bag is found to change its shape and hence its dynamic response, while varying the turbine damping or the air volume ratio changes the dynamic response without changing the shape.

Biomechanical evaluation of occupant anthropometry during frontal collisions.

PubMed

Frieder, Russell; Kumar, Sri; Sances, Anthony

2007-01-01

The present study examines the biomechanical implications of 3-point lap/shoulder seat belts and frontal air bags to the injury probabilities for occupants of varying anthropometry, during frontal collisions. Using Mathematical Dynamic Modeling (MADYMO) software, a variety of simulated frontal crash tests were conducted to evaluate the effectiveness of seat belts and air bags in reducing probability of injury to different sized occupants. The simulations included virtual models of the 5th percentile female, 50th percentile male, and 95th percentile male to represent three occupant size classes. The test matrix paired each of these dummy sizes with four restraint system configurations. The configurations examined were seat belt only, air bag only, both seat belt and air bag, and none. Each of the simulated crashes was modeled to replicate a direct (12 O'clock) frontal collision with a total change in velocity of 56.3kph. Likelihood of serious injury was determined through the calculation of Head Injury Criteria (HIC,36ms), angular acceleration of the head center of gravity, and the Nij neck injury criteria. The results generally suggested that air bags produce a more significant reduction in HIC for larger belted occupants than they do for smaller belted occupants, and that whether belted or not, smaller occupants received the largest reduction in head CG angular acceleration due to the existence of an air bag. Though clear trends were not noted in the neck injury values, it was noted that the simulations with out air bags produced two results that failed the injury criterion, while no serious neck injuries would be expected based on the values produced in the simulations with air bags. The study suggested that a properly timed air bag deployment can reduce injury potential for all occupants of all sizes, but that the magnitude of this benefit is dependent on anthropometry.

The continued burden of spine fractures after motor vehicle crashes.

PubMed

Wang, Marjorie C; Pintar, Frank; Yoganandan, Narayan; Maiman, Dennis J

2009-02-01

Spine fractures are a significant cause of morbidity and mortality after motor vehicle crashes (MVCs). Public health interventions, such as the National Highway Traffic Safety Administration's Federal Motor Vehicle Safety Standards, have led to an increase in automobiles with air bags and the increased use of seat belts to lessen injuries sustained from MVCs. The purpose of this study was to evaluate secular trends in the occurrence of spine fractures associated with MVCs and evaluate the association between air bag and seat belt use with spine fractures. Using the Crash Outcome Data Evaluation System, a database of the police reports of all MVCs in Wisconsin linked to hospital records, the authors studied the occurrence of spine fractures and seat belt and air bag use from 1994 to 2002. Demographic information and crash characteristics were obtained from the police reports. Injury characteristics were determined using International Classification of Disease, 9th Revision, Clinical Modification (ICD-9-CM) hospital discharge codes. From 1994 to 2002, there were 29,860 hospital admissions associated with automobile or truck crashes. There were 20,276 drivers or front-seat passengers 16 years of age and older who were not missing ICD-9-CM discharge codes, seat belt or air bag data, and who had not been ejected from the vehicle. Of these, 2530 (12.5%) sustained a spine fracture. The occurrence of spine fractures increased over the study period, and the use of a seat belt plus air bag, and of air bags alone also increased during this period. However, the occurrence of severe spine fractures (Abbreviated Injury Scale Score > or =3) did not significantly increase over the study period. The use of both seat belt and air bag was associated with decreased odds of a spine fracture. Use of an air bag alone was associated with increased odds of a severe thoracic, but not cervical spine fracture. Among drivers and front-seat passengers admitted to the hospital after MVCs, the occurrence of spine fractures increased from 1994 to 2002 despite concomitant increases in seat belt and air bag use. However, the occurrence of severe spine fractures did not increase over the study period. The use of both seat belt and air bag is protective against spine fractures. Although the overall increased occurrence of spine fractures may appear contrary to the increased use of seat belts and air bags in general, it is possible that improved imaging technology may be associated with an increase in the diagnosis of relatively minor fractures. However, given the significant protective effects of both seat belt and air bag use against spine fractures, resources should continue to be dedicated toward increasing their use to mitigate the effects of MVCs.

Effects of child age and body size on serious injury from passenger air-bag presence in motor vehicle crashes.

PubMed

Newgard, Craig D; Lewis, Roger J

2005-06-01

Current recommendations regarding children traveling in passenger vehicles equipped with passenger air bags are based, in part, on evidence that the air-bag-related risk of injury and death is higher for children < or =12 years of age. However, the age or body size required to allow a child to be seated safely in front of a passenger air bag is unknown. To evaluate specific cutoff points for age, height, and weight as effect modifiers of the association between the presence of a passenger air bag and serious injury among children involved in motor vehicle crashes (MVCs), while controlling for important crash factors. A national population-based cohort of children involved in MVCs and included in the National Automotive Sampling System (NASS) Crashworthiness Data System (CDS) database from 1995 to 2002 was studied. NASS CDS clusters, strata, and weights were included in all analyses. Children 0 to 18 years of age involved in MVCs and seated in the right front passenger seat. Serious injury, defined as an Abbreviated Injury Scale score of > or =3 for any body region. A total of 3790 patients (1 month to 18 years of age) were represented in the NASS CDS database during the 8-year period. Sixty children (1.6%) were seriously injured (Abbreviated Injury Scale score of > or =3). Among age, height, and weight, age of 0 to 14 years (versus 15-18 years) was the only consistent effect modifier of the association between air-bag presence (or air-bag deployment) and serious injury, particularly for crashes with a moderate probability of injury. In analyses stratified according to age and adjusted for important crash factors, children 0 to 14 years of age involved in frontal collisions seemed to be at increased risk of serious injury from air-bag presence (odds ratio [OR]: 2.66; 95% confidence interval [CI]: 0.23-30.9) and deployment (OR: 6.13; 95% CI: 0.30-126), although these values did not reach statistical significance. Among children 15 to 18 years of age involved in frontal collisions, there was a protective effect on injury from both air-bag presence (OR: 0.19; 95% CI: 0.05-0.75) and deployment (OR: 0.31; 95% CI: 0.09-0.99). These findings persisted in analyses involving all collision types. We did not identify similar cutoff points for height or weight. Children up to 14 years of age may be at risk for serious preventable injury when seated in front of a passenger air bag, and children 15 to 18 years of age seem to experience protective effects of air-bag presence and deployment. Age may be a better marker than height or weight for risk assessment regarding children and air bags.

Air bags and passenger fatality according to passenger age and restraint use.

PubMed

Cummings, Peter; Koepsell, Thomas D; Rivara, Frederick P; McKnight, Barbara; Mack, Christopher

2002-09-01

Some children have been killed by air bags, leading to advice that young children should not sit in front of an active air bag. We conducted a case-control study to estimate the association of passenger air bag presence with death, according to passenger age and seat belt use. We used data from crashes on U.S. public roads in 1992 through 1998. Cases (N = 20,987) were front seat passengers who died, and controls (N = 69,277) were a sample of survivors. Among restrained passengers, the adjusted relative risk of death for those with a passenger air bag was 0.79 (95% confidence interval [CI] = 0.66-0.94); for children 12 years or younger, the adjusted relative risk was 1.04 (0.65-1.67) [corrected], and for adults 20 years or older it was 0.75 (0.62-0.91) [corrected]. Among unrestrained passengers, the adjusted relative risk was 1.03 (CI = 0.81-1.30); for children 12 years or younger the adjusted relative risk was 1.37 (0.84-2.21) [corrected], and for adults 20 years or older it was 0.96 (0.75-1.24). Passenger air bags may be a hazard to unrestrained children and of little benefit to unrestrained adults. Our results support the advice that children younger than 13 years should not sit in front of an active air bag.

75 FR 19453 - Reports, Forms and Record Keeping Requirements; Agency Information Collection Activity Under OMB...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-14

... Administration Title: Air Bag Deactivation. OMB Number: 2127-0588. Type of Request: Extension of a currently approved information collection. Abstract: If a private individual or lessee wants to install an air bag on-off switch to turn-off either or both frontal air bags, they must complete Form OMB 2127-0588 to...

78 FR 32009 - Technical Report on the Injury Vulnerability of Older Occupants and Women

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-28

..., but more effective for female drivers. Frontal air bags are about equally effective across all ages; side air bags may be even more effective for older occupants than for young adults. Air bags and other... Technologies for Older Occupants and Women. DATES: Comments must be received no later than September 25, 2013...

75 FR 70071 - Terrafugia, Inc.; Receipt of Application for Temporary Exemption From Requirements for Tire...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-16

.... 205), and occupant crash protection, specifically advanced air bags (FMVSS No. 208). The basis for the... systems (FMVSS No. 126), glazing materials (FMVSS No. 205), and advanced air bags (FMVSS No. 208). The... advanced air bags. According to the petition, the three-year requested exemption period will give the...

Prediction of air temperature for thermal comfort of people using sleeping bags: a review

NASA Astrophysics Data System (ADS)

Huang, Jianhua

2008-11-01

Six models for determining air temperatures for thermal comfort of people using sleeping bags were reviewed. These models were based on distinctive metabolic rates and mean skin temperatures. All model predictions of air temperatures are low when the insulation values of the sleeping bag are high. Nevertheless, prediction variations are greatest for the sleeping bags with high insulation values, and there is a high risk of hypothermia if an inappropriate sleeping bag is chosen for the intended conditions of use. There is, therefore, a pressing need to validate the models by wear trial and determine which one best reflects ordinary consumer needs.

Prediction of air temperature for thermal comfort of people using sleeping bags: a review.

PubMed

Huang, Jianhua

2008-11-01

Six models for determining air temperatures for thermal comfort of people using sleeping bags were reviewed. These models were based on distinctive metabolic rates and mean skin temperatures. All model predictions of air temperatures are low when the insulation values of the sleeping bag are high. Nevertheless, prediction variations are greatest for the sleeping bags with high insulation values, and there is a high risk of hypothermia if an inappropriate sleeping bag is chosen for the intended conditions of use. There is, therefore, a pressing need to validate the models by wear trial and determine which one best reflects ordinary consumer needs.

Do seat belts and air bags reduce mortality and injury severity after car accidents?

PubMed

Cummins, Justin S; Koval, Kenneth J; Cantu, Robert V; Spratt, Kevin F

2011-03-01

We studied National Trauma Data Bank data to determine the effectiveness of car safety devices in reducing mortality and injury severity in 184,992 patients between 1988 and 2004. Safety device variables were seat belt used plus air bag deployed; only seat belt used; only air bag deployed; and, as explicitly coded, no device used. Overall mortality was 4.17%. Compared with the no-device group, the seat-belt-plus-air-bag group had a 67% reduction in mortality (adjusted odds ratio [AOR], 0.33; 99% confidence interval [CI], 0.28-0.39), the seatbelt- only group had a 51% mortality reduction (AOR, 0.49; 99% CI, 0.45-0.52), and the air-bag-only group had a 32% mortality reduction (AOR, 0.68, 99% CI, 0.57-0.80). Injury Severity Scores showed a similar pattern.

Development of Spray on Bag for manufacturing of large composites parts: Diffusivity analysis

NASA Astrophysics Data System (ADS)

Dempah, Maxime Joseph

Bagging materials are utilized in many composites manufacturing processes. The selection is mainly driven by cost, temperature requirements, chemical compatibility and tear properties of the bag. The air barrier properties of the bag are assumed to be adequate or in many cases are not considered at all. However, the gas barrier property of a bag is the most critical parameter, as it can negatively affect the quality of the final laminate. The barrier property is a function of the bag material, uniformity, thickness and temperature. Improved barrier properties are needed for large parts, high pressure consolidated components and structures where air stays entrapped on the part surface. The air resistance property of the film is defined as permeability and is investigated in this thesis. A model was developed to evaluate the gas transport through the film and an experimental cell was implemented to characterize various commercial films. Understanding and characterizing the transport phenomena through the film allows optimization of the bagging material for various manufacturing processes. Spray-on-Bag is a scalable alternative bagging method compared to standard films. The approach allows in-situ fabrication of the bag on large and complex geometry structures where optimization of the bag properties can be varied on a local level. An experimental setup was developed and implemented using a six axis robot and an automated spraying system. Experiments were performed on a flat surface and specimens were characterized and compared to conventional films. Air barrier properties were within range of standard film approaches showing the potential to fabricate net shape bagging structures in an automated process.

49 CFR Appendix C to Part 595 - Installation of Air Bag On-Off Switches

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Installation of Air Bag On-Off Switches C Appendix C to Part 595 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL... EXEMPTIONS Pt. 595, App. C Appendix C to Part 595—Installation of Air Bag On-Off Switches ER21NO97.012 ...

76 FR 37025 - Make Inoperative Exemptions; Vehicle Modifications To Accommodate People With Disabilities, Side...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-24

... the seat. Many vehicles will depend on side impact air bag technology to meet all of the injury... installing side air bags in vehicle seats and/or door panels and side roof rails. The phase-in of the... expressed concern that: ``* * * torso side air bags are commonly installed in the outboard side of the OEM...

49 CFR Appendix C to Part 595 - Installation of Air Bag On-Off Switches

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Installation of Air Bag On-Off Switches C Appendix C to Part 595 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL... EXEMPTIONS Pt. 595, App. C Appendix C to Part 595—Installation of Air Bag On-Off Switches ER21NO97.012 ...

49 CFR Appendix C to Part 595 - Installation of Air Bag On-Off Switches

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Installation of Air Bag On-Off Switches C Appendix C to Part 595 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL... EXEMPTIONS Pt. 595, App. C Appendix C to Part 595—Installation of Air Bag On-Off Switches ER21NO97.012 ...

49 CFR Appendix C to Part 595 - Installation of Air Bag On-Off Switches

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Installation of Air Bag On-Off Switches C Appendix C to Part 595 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL... EXEMPTIONS Pt. 595, App. C Appendix C to Part 595—Installation of Air Bag On-Off Switches ER21NO97.012 ...

49 CFR Appendix C to Part 595 - Installation of Air Bag On-Off Switches

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Installation of Air Bag On-Off Switches C Appendix C to Part 595 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL... EXEMPTIONS Pt. 595, App. C Appendix C to Part 595—Installation of Air Bag On-Off Switches ER21NO97.012 ...

The effectiveness of air bags.

PubMed

Barry, S; Ginpil, S; O'Neill, T J

1999-11-01

Previous research has shown that the installation of air bags in vehicles significantly reduces crash related deaths, but these analyses have used statistical techniques which have not been capable of controlling for other major determinants of crash survival. This study analysed data from the US FARS database of fatal crashes using conditional logistic regression which is simultaneously able to estimate occupant protection effects for a range of variables. Results of the analysis provided a comparative quantification of both the effect of the air bag as well as other well known determinants of occupant crash survival (age, seat belt use, and gender). When potentially confounding variables were controlled, both the driver and passenger side air bag devices were shown to significantly reduce the probability of death in direct frontal collisions, but the effect size calculated was small compared to the effect of the seat belt. The effect size may also be very small in absolute terms depending on the severity of the crash involved. Given the limited benefit of the air bag, efforts to promote air bags seem particularly difficult to justify in countries such as the United States where the vastly superior occupant protection of the seat belt is under-utilised.

Injury risk to restrained children exposed to deployed first- and second-generation air bags in frontal crashes.

PubMed

Arbogast, Kristy B; Durbin, Dennis R; Kallan, Michael J; Elliott, Michael R; Winston, Flaura K

2005-04-01

To estimate the risk of serious nonfatal injuries in frontal crashes among belted children seated in the right front seat of vehicles in which second-generation passenger air bags deployed compared with that of belted children seated in the right front seat of vehicles in which first-generation passenger air bags deployed. We enrolled a probability sample of 1781 seat belt-restrained occupants aged 3 through 15 years seated in the right front seat, exposed to deployed passenger air bags in frontal crashes involving insured vehicles in 3 large US regions, between December 1, 1998, and November 30, 2002. A telephone interview was conducted with the driver of the vehicle using a previously validated instrument. The study sample was weighted according to each subject's probability of selection, with analyses conducted on the weighted sample. Main Outcome Measure Risk of serious injury (Abbreviated Injury Scale score of > or =2 injuries and facial lacerations). The risk of serious injury for restrained children in the right front seat exposed to deployed second-generation passenger air bags was 9.9%, compared with 14.9% for similar children exposed to deployed first-generation passenger air bags (adjusted odds ratio, 0.59; 95% confidence interval, 0.36-0.97). This study provides evidence based on field data that the risk of injury to children exposed to deploying second-generation passenger air bags is reduced compared with earlier designs.

Investigation of a relationship between external force to shoulder and chest injury of WorldSID and THUMS in 32 km/h oblique pole side impact.

PubMed

Tanaka, Shinobu; Hayashi, Shigeki; Fukushima, Satoshi; Yasuki, Tsuyoshi

2013-01-01

This article describes the chest injury risk reduction effect of shoulder restraints using finite element (FE) models of the worldwide harmonized side impact dummy (WorldSID) and Total Human Model for Safety (THUMS) in an FE model 32 km/h oblique pole side impact. This research used an FE model of a mid-sized vehicle equipped with various combinations of curtain shield air bags, torso air bags, and shoulder restraint air bags. As occupant models, AM50 WorldSID and THUMS AM50 Version 4 were used for comparison. The research investigated the effect of shoulder restraint air bag on chest injury by comparing cases with and without a shoulder side air bag. The maximum external force to the chest was reduced by shoulder restraint air bag in both WorldSID and THUMS, reducing chest injury risk as measured by the amount of rib deflection, number of the rib fractures, and rib deflection ratio. However, it was also determined that the external force to shoulder should be limited to the chest injury threshold because the external shoulder force transmits to the chest via the arm in the case of WorldSID and via the scapula in the case of THUMS. Because these results show the shoulder restraint air bag effect on chest injury risk, the vent hole size of the shoulder restraint air bag was changed for varying reaction forces to investigate the relationship between the external force to the shoulder and the risk of chest injury. In the case of THUMS, an external shoulder force of 1.8 kN and more force from the shoulder restraint air bag was necessary to help prevent rib fracture. Increasing external force applied to shoulder up to 6.2 kN (the maximum force used in this study) did not induce any rib or clavicle fractures in the THUMS. When the shoulder restraint air bag generated external force to the shoulder from 1.8 to 6.2 kN in THUMS, which were applied to the WorldSID, the shoulder deflection ranged from 35 to 68 mm, and the shoulder force ranged from 1.8 to 2.3 kN. In the test configuration used, a shoulder restraint using the air bag helps reduce chest injury risk by lowering the maximum magnitude of external force to the shoulder and chest. To help reduce rib fracture risk in the THUMS, the shoulder restraint air bag was expected to generate a force of 3.7 kN with a minimum rib deflection ratio. This corresponds to a shoulder rib deflection of 60 mm and a shoulder load of 2.2 kN in WorldSID. Supplemental materials are available for this article. Go to the publisher's online edition of Traffic Injury Prevention to view the supplemental file.

76 FR 33406 - Lotus Cars Ltd. Receipt of Petition for Renewal of Temporary Exemption From the Advanced Air Bag...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-08

...-0069] Lotus Cars Ltd. Receipt of Petition for Renewal of Temporary Exemption From the Advanced Air Bag... accordance with the procedures in 49 CFR Part 555, Lotus Cars Ltd. has petitioned the agency for renewal of a... 2000, NHTSA upgraded the requirements for air bags in passenger cars and light trucks, requiring what...

78 FR 65426 - Technical Report: Evaluation of the Certified-Advanced Air Bags

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-31

... INFORMATION CONTACT: Nathan K. Greenwell, Mathematical Statistician, Evaluation Division, NVS-431, National Center for Statistics and Analysis, National Highway Traffic Safety Administration, Room W53-438, 1200... bags at all for children, using occupant detection sensors to suppress the air bags. Statistical...

A rare case of blunt thoracoabdominal trauma with small bowel perforation from air bags.

PubMed

Liverani, A; Pezzatini, M; Conte, S; Mari, F; Milillo, A; Gasparrini, M; Marino, G; Catracchia, V; -Favi, F

2009-05-01

Vehicle collisions represent more than 75% of mechanism of blunt abdominal trauma. In spite of the incomparable improvement of car safety devices, recent studies pointed out that the air bags might cause injuries, specially when it is not associated with seatbelt. In fact, some studies pointed out that crash victims using air bags alone have increased injury severity, hospitalisations, thoracoabdominal procedure, and rehabilitation. Some of the most frequently injured organs reported from air bag deployment are the liver (38%), the spleen (23%) and digestive system (17%). Injury of the hollow viscera are far less common. In particular, blunt abdominal trauma resulting in small bowel perforation is an infrequent lesion. These injuries are difficult to diagnose because specific signs are poor and a delay in treatment increases mortality and morbidity of the patients. We describe a case of thoracoabdominal trauma that occurred during a head-on collision after an air bag deployment without seatbelt use.

Risk of injury associated with the use of seat belts and air bags in motor vehicle crashes.

PubMed

Cummins, Justin S; Koval, Kenneth J; Cantu, Robert V; Spratt, Kevin F

2008-01-01

Although air bags have been reported to reduce passenger mortality in frontal collisions, they have also been reported as a cause of injury in motor vehicle collisions(MVCs). The purpose of this study was to evaluate a large cohort of patients involved in MVCs to determine mortality and the pattern of injuries associated with seat belt use and air bag deployment. Information on patients involved in MVCs from 1988 to 2004 was obtained from the National Trauma Data Bank (NTDB). The data was evaluated based on four groups of safety devices: seat belt and deployed air bag (SBAB), seat belt only (SBO), deployed air bag only (ABO), and no safety devices (None). A total of 35,333 patients met study inclusion criteria. Air bags and seat belts used in combination decreased the risk of potentially fatal injuries, but increased the risk of lower extremity injuries (odds ratio, 1.35). The use of any type of restraint led to a decrease in the risk of injury or mortality in MVCs. Only half of all individuals in this study used any type of restraint device, which indicates the need for significant improvements in public health and safety seat belt utilization programs.

[Awareness of the risk of air bag-associated injuries essential].

PubMed

Björnstig, Ulf; Haraldsson, Per-Olle; Polland, Werner; Sandström, Thomas

2002-07-11

Restraint systems, such as air bags and seat belts with pretensioners, reduce effectively the risk of serious injuries of car occupants. However, this equipment may have some adverse effects. In a frontal air bag deployment the cushion expands with a speed of about 200 km/h towards the driver. A person within the expansion zone, i.e. within 20 centimetres from the steering wheel hub, may experience a considerable injury risk. Short people, pregnant women and people "out of normal position" are especially at risk, as well as paramedics exposed for accidentally deployed air bags during rescue work. The gas generator in the air bag produces nitrogen in a chemical process. However, small amounts of NaOH (caustic soda) may leak out of the gas generator and may contaminate eyes and wounds and cause injuries and delay healing. The air bag gases may provoke an asthmatic attack in sensible individuals and a few will experience a hearing loss, often in the range of 4,000-6,000 Hz, from the sound impulse that may reach a level of 170 dB. Correct handling, based on a familiarity of the effects and side effects of modern restraint systems, would minimise the risk of adverse effects of this safety equipment.

Performance tests of three types of air-sampling bags on organic solvent vapor retention.

PubMed

Fukui, Yoshinari; Kanemaru, Ai; Nagasawa, Yasuhiro; Kawakami, Takuya; Iwata, Toyoto; Murata, Katsuyuki; Ohashi, Fumiko; Ikeda, Masayuki

2013-01-01

Performance of two new air sampling bags [the transparent bag (TP bag) and the semi-transparent bag (ST bag)] was examined as possible surrogates for the traditional PVF bag (the Ref bag). Solvent vapor mixture of butyl acetate, chloroform, ethyl acetate, isopropyl alcohol and toluene at administrative control levels were introduced to each bag (n=5 for each of the three types), and the decay in the concentrations (by%) was followed by use of a gas auto-sampler - FID-GC system. A trend of time-dependent decay was noted for all types including the Ref bag. When the performance was compared, the TP bag was equal to or even better than the Ref bag. In contrast, the performance of the ST bag was comparable to that of the other two types of bags with regard to toluene and chloroform when the storage time was short, but poorer than others for the other three solvents throughout the test period. The TP bag may be a bag of choice when the storage time is extended (e.g., up to 48 h) although this bag is physically less robust and requires careful handling. The ST bag may be used when analysis will be completed within 24 h.

Double-layer Tedlar bags: a means to limit humidity evolution of air samples and to dry humid air samples.

PubMed

Cariou, Stephane; Guillot, Jean-Michel

2006-01-01

Tedlar bags, which are widely used to collect air samples, especially VOCs and odorous atmospheres, can allow humidity to diffuse when relative humidity levels differ between the inside and outside. Starting with dry air inside the bag and humid air outside, we monitored equilibrium times under several conditions showing the evolution and influence of collected volumes and exposed surfaces. A double-film Tedlar bag was made, to limit the impact of external humidity on a sample at low humidity level. With the addition of a drying agent between both films, the evolution of humidity of a sample can be stopped for several hours. When a VOC mixture was monitored in a humid atmosphere, humidity was decreased but no significant evolution of VOC concentrations was observed.

Dimerization Products of Chloroprene are Background Contaminants Emitted from ALTEF (Polyvinylidene Difluoride) Gas Sampling Bags.

PubMed

Kwak, Jae; Fan, Maomian; Martin, Jennifer A; Ott, Darrin K; Grigsby, Claude C

2017-01-01

Gas sampling bags have been used for collecting air samples. Tedlar bags are most commonly used, but bleed background chemicals such as N,N-dimethylacetamide and phenol. It is often necessary to remove the contaminant by flushing the bags with pure nitrogen or air. In this study, we identified four chloroprene dimerization products as background contaminants emitted from ALTEF bags that are made of a proprietary polyvinylidene difluoride (PVDF). No monomer chloroprene was detected in the bags analyzed. All of the dimers gradually increased once bags were filled with nitrogen due to diffusion from the bag surface. Flushing the bags with nitrogen reduced their concentrations, but was not effective for removing the contaminants. When the bags that had been flushed with nitrogen 5 times were left for 24 h, they increased again, indicating that the dimers were constantly emitted from the ALTEF bag surface. To our knowledge, these compounds have never been demonstrated in ALTEF or other PVDF bags. Our finding indicates that ALTEF might be incorporated with Neoprene (chloroprene-based polymer) during its manufacturing process.

Differences in the effectiveness of frontal air bags by body size among adults involved in motor vehicle crashes.

PubMed

Newgard, Craig D; McConnell, K John

2008-10-01

There is concern that small stature occupants (particularly women) involved in motor vehicle crashes (MVCs) may be at risk of injury or death from frontal air bags, though evidence to substantiate this concern is lacking. We sought to assess how occupant body size (measured through height and weight) affects air bag effectiveness in mitigating the risk of serious injury, after adjusting for important crash factors. This was a retrospective cohort study using a national population-based cohort of adult front-seat occupants involved in MVCs as included in the National Automotive Sampling System Crashworthiness Data System database (NASS CDS) from 1995 to 2006. Drivers and front-seat passengers 15 years and older involved in MVCs involving passenger vehicles and light trucks were included in the analysis. The primary outcome was serious injury, defined as an Abbreviated Injury Scale (AIS) score >or=3 in any body region. Multivariable logistic regression models were used to test interaction terms (effect modification) between air bags, body size, and injury. The predicted probability of injury across body sizes was plotted to further illustrate potential differences. Sixty-nine thousand three hundred eighty-seven adult front-seat occupants during the 12-year period were included in the analysis, of which 9333 (2.3%) were seriously injured. There was no evidence that height or weight modified air bag effectiveness among all crashes (p > .40). In primary frontal collisions, there was some evidence for effect modification by weight (p = .04) but not by height (p = .59). When assessed using air bag deployment, height was a strong effect modifier (p = .0078), but not weight (p = .43). Predicted probability figures confirmed that occupant height modifies the effect of air bag deployment, but there was no similar visual evidence for body weight. In this sample, we found no consistent evidence that body size modifies the overall effectiveness of frontal air bags. However, among crashes involving air bag deployment, the effect of deployment on injury differs by occupant height, with a relative increase in the odds of serious injury among smaller occupants. In such crashes, the probability of injury with (versus without) deployment began to increase with occupant heights less than 155 cm (5'), reaching a level of statistical difference below 138 cm (4' 6'').

The influence of air bags and restraining devices on extremity injuries in motor vehicle collisions.

PubMed

McGovern, M K; Murphy, R X; Okunski, W J; Wasser, T E

2000-05-01

The influence of air bags and other restraining devices on injury after motor vehicle collisions is not well defined. This study examined the relationship between the use of restraining devices and the incidence of extremity injuries in motor vehicle collisions. A retrospective analysis was performed on motor vehicle collision data submitted to the Pennsylvania Trauma Outcome Study database from 1990 through 1995. Criteria for submission included trauma patients who were admitted to the intensive care unit, who died during hospitalization, who were hospitalized for more than 72 hours, or who were transferred in or out of the receiving hospital. A total of 21,875 patients met these criteria. These patients were analyzed for the presence or absence of upper and lower extremity injuries and were compared based on their use of restraining devices. Restraining devices were categorized into four groups: air bag alone, air bag and seat belt, seat belt or carseat without air bag, and no restraining device. Statistical analysis was performed using the chi-squared test of association. For contingency tables with small expected frequencies, Fisher's exact test was used. Study participants included 11,688 men and 10,185 women with a mean age of 38 +/- 20 years. There were 16,033 drivers and 5,842 passengers. Air bags were deployed in 472 instances. In 297 of these cases, additional restraint was provided with a seat belt. In 6,632 cases, air bags were not deployed; however, patients were restrained with either a seat belt or a carseat. In 14,771 cases, patients were not restrained. When comparing restraining devices as a group vs. no restraint, there was a significant decrease in the incidence of upper (p = 0.018) and lower (p < 0.001) extremity injuries. Air bags, however, were associated with an increased incidence of both upper (p = 0.033) and lower (p = 0.002) extremity injuries when compared with no restraint or when compared among patients who were restrained. As a group, restraining devices decrease the incidence of upper and lower extremity trauma sustained by patients injured in motor vehicle collisions. Air bags, however, are associated with an increased incidence of upper and lower extremity injuries when compared with seat belts alone or when no restraining devices are used.

49 CFR 585.12 - Purpose.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting... Traffic Safety Administration in determining whether a manufacturer has complied with the advanced air bag...

49 CFR 585.12 - Purpose.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting... Traffic Safety Administration in determining whether a manufacturer has complied with the advanced air bag...

49 CFR 585.12 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting... Traffic Safety Administration in determining whether a manufacturer has complied with the advanced air bag...

49 CFR 585.12 - Purpose.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting... Traffic Safety Administration in determining whether a manufacturer has complied with the advanced air bag...

49 CFR 585.12 - Purpose.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting... Traffic Safety Administration in determining whether a manufacturer has complied with the advanced air bag...

Dynamic Response of the Hybrid III 3 Year Old Dummy Head and Neck During Side Air Bag Loading

PubMed Central

Duma, Stefan M.; Crandall, Jeff R.; Pilkey, Walter D.; Seki, Kazuhiro; Aoki, Takashi

1998-01-01

This paper presents the results from fourteen (n = 14) tests designed to evaluate the response and injury potential of a Hybrid III 3 year old dummy subject to loading by a deploying seat mounted side air bag. An instrumented Hybrid III 3 year old dummy was used for tests in two different occupant positions chosen to maximize head and neck loading. Four seat mounted thoracic side air bags were used that varied only in the level of inflator output. NHTSA’s neck injury criteria for complex loading, referred to as Nij, was modified to include moment values for both anterioposterior and lateral directions. The results of this testing indicate that side air bag loading can result in forces and moments approaching injury threshold values. While there is considerable uncertainty as to the validity of published injury criteria due to the lack of child biomechanical data, this study demonstrates the sensitivity of child response to initial position which may provide insight into placement and geometry of side airbag systems. Furthermore, the data indicates a relationship between airbag inflator properties and child dummy response for a given airbag geometry. Recently, automobile manufacturers have begun implementing side air bags as a safety feature to mitigate injuries resulting from side impact collisions. Unlike the case for the passenger side air bag, the injury potential to an out-of-position child in side airbag loading has not been presented in the literature. The purpose of this research is to evaluate the response of a Hybrid III 3 year old dummy subject to loading by a deploying side air bag.

Air bags and ocular injuries.

PubMed

Stein, J D; Jaeger, E A; Jeffers, J B

1999-01-01

This investigation retrospectively examined ocular injuries associated with air bag deployment to gain a better appreciation of potential risk factors in motor vehicle accidents. National statistics regarding the efficacy of air bags were reviewed. Review of the literature from 1991 to 1998 identified 44 articles describing 97 patients with air-bag-induced ocular injuries. Variables extracted from each case were age, sex, height, position in the car, eye wear, vehicle impact speed, visual acuity, and specific ocular injuries. Corneal abrasions occurred in 49% of occupants, hyphemas in 43%, vitreous or retinal hemorrhages in 25%, and retinal tears or detachments in 15%. The globe was ruptured in 10 patients. Patients involved in higher-speed accidents (over 30 mph) sustained a greater percentage of vitreous or retinal hemorrhages and traumatic cataracts, while those at slower speeds were more prone to retinal tears or detachments. In a subset of 14 patients with serious ocular injuries, the impact speed of 11 patients was recorded at 30 mph or less. Slower speed may be a risk factor for some ocular injuries. Occupant height was not a significant factor. National statistics confirm that air bags reduce fatalities in motor vehicle accidents. However, children sitting in the front seat without a seat belt and infants in passenger-side rear-facing car seats are at risk for fatal injury. Air bags combined with seat belts are an effective means of reducing injury and death in adults during motor vehicle accidents. However, this study has documented a wide variety of ocular injuries associated with air bag deployment. It is hoped that researchers can develop modifications that continue to save lives while minimizing additional harm.

Simulation of air-bag impact on an eye with transsclerally fixated posterior chamber intraocular lens using finite element analysis.

PubMed

Uchio, Eiichi; Kadonosono, Kazuaki; Matsuoka, Yasuhiro; Goto, Satoru

2004-02-01

To determine the physical and mechanical conditions of an impacting air bag that would rupture an eye with a transsclerally fixated posterior chamber intraocular lens (IOL). Numerical simulation study on a computer. Simulations in a model human eye were performed with a computer using the finite element analysis program PAM-CRASH (Nihon ESI). The air bag was set to impact the surface of an eye with a transsclerally fixated posterior chamber IOL at various velocities. The tensile force limit of a 10-1 polypropylene suture was assumed to be 0.16 N, which is specified in the U.S. Pharmacopeia XXII. At the lowest velocity of 20.0 m/s, 10-0 polypropylene sutures were not likely to break. Sutures fixating the IOL might break and a corneoscleral incision was likely to open after 0.3 second at the medium impacting velocity (30 m/s). Suture rupture was very likely at the highest velocity (40 m/s) since the tensile force on the sutures continuously exceeded the breaking force after the impact. In an eye with a transsclerally fixated posterior chamber IOL, severe ocular trauma can be caused by an air bag at high velocity. Small individuals such as elderly women are at greater risk for air-bag ocular injury. Further research on modifying air-bag design and deployment is important to minimize the risk for ocular injury.

Modeling and Simulation of the Second-Generation Orion Crew Module Air Bag Landing System

NASA Technical Reports Server (NTRS)

Timmers, Richard B.; Welch, Joseph V.; Hardy, Robin C.

2009-01-01

Air bags were evaluated as the landing attenuation system for earth landing of the Orion Crew Module (CM). An important element of the air bag system design process is proper modeling of the proposed configuration to determine if the resulting performance meets requirements. Analysis conducted to date shows that airbags are capable of providing a graceful landing of the CM in nominal and off-nominal conditions such as parachute failure, high horizontal winds, and unfavorable vehicle/ground angle combinations. The efforts presented here surround a second generation of the airbag design developed by ILC Dover, and is based on previous design, analysis, and testing efforts. In order to fully evaluate the second generation air bag design and correlate the dynamic simulations, a series of drop tests were carried out at NASA Langley's Landing and Impact Research (LandIR) facility. The tests consisted of a full-scale set of air bags attached to a full-scale test article representing the Orion Crew Module. The techniques used to collect experimental data, construct the simulations, and make comparisons to experimental data are discussed.

Comparison of storage stability of odorous VOCs in polyester aluminum and polyvinyl fluoride tedlar bags

USDA-ARS?s Scientific Manuscript database

Whole air sampling using containers such as flexible bags or rigid canisters is commonly used to collect samples of volatile organic compounds (VOC) in air. The objective of this study was to compare the stability of polyester aluminum (PEA) and polyvinyl fluoride (PVF, brand name Tedlar®) bags for ...

40 CFR 63.1184 - What do I need to know about the design specifications, installation, and operation of a bag leak...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., each compartment or cell must have a bag leak detector. For a negative-pressure or induced-air fabric... design specifications, installation, and operation of a bag leak detection system? 63.1184 Section 63.1184 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED...

40 CFR 63.1184 - What do I need to know about the design specifications, installation, and operation of a bag leak...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., each compartment or cell must have a bag leak detector. For a negative-pressure or induced-air fabric... design specifications, installation, and operation of a bag leak detection system? 63.1184 Section 63.1184 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED...

40 CFR 63.1184 - What do I need to know about the design specifications, installation, and operation of a bag leak...

Code of Federal Regulations, 2012 CFR

2012-07-01

..., each compartment or cell must have a bag leak detector. For a negative-pressure or induced-air fabric... design specifications, installation, and operation of a bag leak detection system? 63.1184 Section 63.1184 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED...

Air bags: a major advance in injury control.

PubMed

Jordan, K S

1999-01-01

Motor vehicle related injury is the number one cause of injury related to morbidity and mortality, exceeding 5 million injuries per year. There is a growing body of scientific evidence that motor vehicles equipped with air bags make a significant impact in reducing both the severity of injury and the overall fatality rate. Nurses are a key resource in the prevention and mitigation of motor vehicle related injury. Nurses must not only be knowledgeable in the vital role that air bags play in motor vehicle crashes, but actively promote and educate individuals and groups regarding injury prevention programs that focus on air bags. Nurses also play an essential role in this approach to injury through the development of partnerships among businesses, government, health care, community groups, and consumers.

Investigation of the Landing Characteristics of a Re-entry Vehicle Having a Canted Multiple Air Bag Load Alleviation System

NASA Technical Reports Server (NTRS)

McGehee, John R.; Stubbs, Sandy M.

1963-01-01

An investigation was made to determine the landing-impact characteristics of a reentry vehicle having a multiple-air-bag load-alleviation system. A 1/16-scale dynamic model having four canted air bags was tested at flight-path angles of 90 degrees (vertical), 45 degrees, and 27 degrees for a parachute or paraglider vertical letdown velocity of 30 feet per second (full scale). Landings were made on concrete at attitudes ranging from -l5 degrees to 20 degrees. The friction coefficient between the model heat shield and the concrete was approximately 0.4. An aluminum diaphragm, designed to rupture at 10.8 pounds per square inch gage, was used to maintain initial pressure in the air bags for a short time period.

40 CFR 63.11468 - What are the monitoring requirements for new and existing sources?

Code of Federal Regulations, 2011 CFR

2011-07-01

... baghouse, including but not limited to air leaks, torn or broken bags or filter media, or any other...) Inspecting the fabric filter for air leaks, torn or broken bags or filter media, or any other condition that... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR...

40 CFR 63.11468 - What are the monitoring requirements for new and existing sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

... baghouse, including but not limited to air leaks, torn or broken bags or filter media, or any other...) Inspecting the fabric filter for air leaks, torn or broken bags or filter media, or any other condition that... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR...

40 CFR 63.11468 - What are the monitoring requirements for new and existing sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

... baghouse, including but not limited to air leaks, torn or broken bags or filter media, or any other...) Inspecting the fabric filter for air leaks, torn or broken bags or filter media, or any other condition that... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR...

40 CFR 63.11468 - What are the monitoring requirements for new and existing sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

... baghouse, including but not limited to air leaks, torn or broken bags or filter media, or any other...) Inspecting the fabric filter for air leaks, torn or broken bags or filter media, or any other condition that... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR...

Wave energy absorption by a submerged air bag connected to a rigid float.

PubMed

Kurniawan, A; Chaplin, J R; Hann, M R; Greaves, D M; Farley, F J M

2017-04-01

A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements are generally in good agreement with numerical predictions. Both show that the trajectory of possible combinations of pressure and elevation at which the device is in static equilibrium takes the shape of an S. This means that statically the device can have three different draughts, and correspondingly three different bag shapes, for the same pressure. The behaviour in waves depends on where the mean pressure-elevation condition is on the static trajectory. The captured power is highest for a mean condition on the middle section.

Wave energy absorption by a submerged air bag connected to a rigid float

PubMed Central

Chaplin, J. R.; Hann, M. R.; Greaves, D. M.; Farley, F. J. M.

2017-01-01

A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements are generally in good agreement with numerical predictions. Both show that the trajectory of possible combinations of pressure and elevation at which the device is in static equilibrium takes the shape of an S. This means that statically the device can have three different draughts, and correspondingly three different bag shapes, for the same pressure. The behaviour in waves depends on where the mean pressure-elevation condition is on the static trajectory. The captured power is highest for a mean condition on the middle section. PMID:28484330

Wave energy absorption by a submerged air bag connected to a rigid float

NASA Astrophysics Data System (ADS)

Kurniawan, A.; Chaplin, J. R.; Hann, M. R.; Greaves, D. M.; Farley, F. J. M.

2017-04-01

A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements are generally in good agreement with numerical predictions. Both show that the trajectory of possible combinations of pressure and elevation at which the device is in static equilibrium takes the shape of an S. This means that statically the device can have three different draughts, and correspondingly three different bag shapes, for the same pressure. The behaviour in waves depends on where the mean pressure-elevation condition is on the static trajectory. The captured power is highest for a mean condition on the middle section.

Jet Inlet Efficiency

DTIC Science & Technology

2013-08-08

Lay down plastic sheeting that is double the size of the mold covered in fabric in order to fully envelope the mold. o Line half of the sheet (in...the mold and connect to clay tape to create an air tight sealed bag with a hose leading to the outside pump. o Once the seal is created, turn on the...connected pump to remove all air from the bag that has been created.  Ensure that as air is removed, the bag fits the form of the desired mold as

Airbag induced facial and bilateral ocular injuries in a 14-year-old child

PubMed Central

Alquraini, Talal A.; Aggour, Mustafa A.; Zamzam, Ahmed M.

2010-01-01

Although air bags have reduced the incidence of fatal and severe injuries in automobile collisions, they have been shown to carry a risk of injury themselves. Ocular injury in particular can often be a direct consequence of air bag deployment. We report a 14-year-old child who sustained facial burn and bilateral ocular injuries affecting both the anterior and posterior segments due to an inflated air bag in a low speed motor vehicle accident. PMID:23960958

40 CFR 86.537-90 - Dynamometer test runs.

Code of Federal Regulations, 2014 CFR

2014-07-01

... “transient” formaldehyde exhaust sample, the “transient” dilution air sample bag, the “transient” methanol... start “transient” exhaust and dilution air bag samples to the analytical system and process the samples... Section 86.537-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...

40 CFR 86.537-90 - Dynamometer test runs.

Code of Federal Regulations, 2012 CFR

2012-07-01

... “transient” formaldehyde exhaust sample, the “transient” dilution air sample bag, the “transient” methanol... start “transient” exhaust and dilution air bag samples to the analytical system and process the samples... Section 86.537-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...

40 CFR 86.537-90 - Dynamometer test runs.

Code of Federal Regulations, 2013 CFR

2013-07-01

... “transient” formaldehyde exhaust sample, the “transient” dilution air sample bag, the “transient” methanol... start “transient” exhaust and dilution air bag samples to the analytical system and process the samples... Section 86.537-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...

Air quality for metals and sulfur in Shanghai, China, determined with moss bags.

PubMed

Cao, Tong; Wang, Min; An, Li; Yu, Yinghao; Lou, Yuxia; Guo, Shuiliang; Zuo, Benrong; Liu, Yan; Wu, Jiming; Cao, Yang; Zhu, Zhirui

2009-04-01

In order to better understand the spatial and temporal distribution pattern of metals and sulfur present in Shanghai, moss bags with Haplocladium microphyllum (Hedw.) Broth. were suspended at 14 local monitoring stations from April through June 2006 in Shanghai, the largest city in China. The results showed that the concentrations of S, Cu, Pb, and Zn in the moss bags after exposure were higher at the sites in the industrial district and most urban districts and lower at the sites in suburban areas, and well correlated with SO(2) API and PM10 API in the air both in terms of space and time. The present study provided evidence that the moss H. microphyllum is suitable for bio-monitoring air pollution with moss bags and further confirmed that the moss-bag method is a simple, inexpensive and useful technique.

Bias of Tedlar bags in the measurement of agricultural odorants.

PubMed

Trabue, Steven L; Anhalt, Jennifer C; Zahn, James A

2006-01-01

Odor regulations typically specify the use of dynamic dilution olfactometery (DDO) as a method to quantify odor emissions, and Tedlar bags are the preferred holding container for grab samples. This study was conducted to determine if Tedlar bags affect the integrity of sampled air from animal operations. Air samples were collected simultaneously in both Tedlar bags and Tenax thermal desorption tubes. Sample sources originated from either a hydrocarbon-free air tank, dynamic headspace chamber (DHC), or swine-production facility, and were analyzed by gas chromatography-mass spectrometry-olfactometry (GC-MS-O). Several background contaminants were identified from Tedlar bags, which included the odorous compounds N,N-dimethyl acetamide (DMAC), acetic acid, and phenol. Samples from the DHC demonstrated that recovery of malodor compounds was dependent on residence time in the Tedlar bag with longer residence time leading to lower recovery. After 24 h of storage, recovery of C3-C6 volatile fatty acids (VFA) averaged 64%, 4-methylphenol and 4-ethylphenol averaged 10%, and indole and 3-methylindole were below the detection limits of GC-MS-O. The odor activity value (OAV) of grab samples collected in Tedlar bags were 33 to 65% lower following 24 h of storage. These results indicate that significant odorant bias occurs when using Tedlar bags for the sampling of odors from animal production facilities.

Driver and front seat passenger fatalities associated with air bag deployment. Part 2: A review of injury patterns and investigative issues.

PubMed

Shkrum, Michael J; McClafferty, Kevin J; Nowak, Edwin S; German, Alan

2002-09-01

Assessment of the role of air bag deployment in injury causation in a crash of any severity requires analysis of occupant, vehicle, and impact data. The potential injurious role of an air bag is independent of crash severity and is more obvious in minor collisions, particularly those involving "out-of-position" occupants. Factors such as occupant height and other constitutional and medical factors, intoxication, age, type, and proper use of other restraint systems, pre-impact braking and multiple impacts can contribute to an occupant being "out-of-position." Two injury mechanisms are described in out-of-position occupants: "punch-out" when the individual covers the air bag module before deployment and "membrane-force" when the occupant contacts a partly deployed air bag. Each mechanism is associated with injury patterns. In adults, "punch-out" can cause thoraco-abdominal trauma and "membrane-force" loading can lead to craniocervical injury. This can also occur in short-statured occupants including children subjected to both types of loading. In more severe collisions, other factors, e.g., intrusion, steering column and seatbelt loading and other occupant compartment contacts, can contribute to trauma.

Driver's side curtain air bag-related globe rupture.

PubMed

Porter, Ashley J; Hayes, Rylan; Lee, Lawrence; O'Hagan, Stephen

2018-06-04

A 35-year-old man presented after a high-speed motor vehicle accident and the driver's side curtain air bag causing blunt force trauma rupturing his right globe. The tangential force of the air bag resulted in an unusual arcuate horseshoe-shaped rupture through the lateral rectus insertion, causing avulsion of the muscle and tearing the sclera, with the apices of the tear extending anteriorly towards the limbus. Repair of the globe rupture was undertaken, and secondary vitrectomy revealed that the scleral tear had not involved the retina abutting the ora serrata. Silicone oil tamponade was used to fill the globe and the postoperative best corrected vision was 6/9. This is the first reported case of a ruptured globe caused by a side curtain air bag, resulting in a uniquely shaped arcuate scleral wound combined with lateral rectus avulsion, not associated with rhegmatogenous retinal damage, and is the first air bag-related globe rupture with scleral involvement to report a final best-corrected visual acuity better than 6/60. © BMJ Publishing Group Ltd (unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

A One-Piece Lunar Regolith-Bag Garage Prototype

NASA Technical Reports Server (NTRS)

Smithers, Gweneth A.; Nehls, Mary K.; Hovater, Mary A.; Evans, Steven W.; Miller, J. Scott; Broughton, Roy M., Jr.; Beale, David; Killinc-Balci, Fatma

2006-01-01

Shelter structures on the moon, even in early phases of exploration, should incorporate lunar materials as much as possible. We designed and constructed a prototype for a one-piece regolith-bag unpressurized garage concept, and, in parallel, we conducted a materials testing program to investigate six candidate fabrics to learn how they might perform in the lunar environment. In our concept, a lightweight fabric form is launched from Earth to be landed on the lunar surface and robotically filled with raw lunar regolith. In the materials testing program, regolith-bag fabric candidates included: VectranTM, NextelTM, Gore PTFE FabricTM, ZylonTM TwaronTM and NomexTM. Tensile (including post radiation exposure), fold, abrasion, and hypervelocity impact testing were performed under ambient conditions, and, within our current means, we also performed these tests under cold and elevated temperatures. In some cases, lunar simulant (JSC-1) was used in conjunction with testing. Our ambition is to continuously refine our testing to reach lunar environmental conditions to the extent possible. A series of preliminary structures were constructed during design of the final prototype. Design is based on the principles of the classic masonry arch. The prototype was constructed of KevlarTM and filled with vermiculite (fairly close to the weight of lunar regolith on the moon). The structure is free-standing, but has not yet been load tested. Our plan for the future would be to construct higher fidelty mockups with each iteration, and to conduct appropriate tests of the structure.

A One-Piece Lunar Regolith-Bag Garage Prototype

NASA Technical Reports Server (NTRS)

Smithers, Gweneth A.; Nehls, Mary K.; Hovater, Mary A.; Evans, Steven W.; Miller, J. Scott; Broughton, Roy M.; Beale, David; Killing-Balci, Fatma

2007-01-01

Shelter structures on the moon, even in early phases of exploration, should incorporate lunar materials as much as possible. We designed and constructed a prototype for a one-piece regolith-bag unpressurized garage concept, and, in parallel, we conducted a materials testing program to investigate six candidate fabrics to learn how they might perform in the lunar environment. In our concept, a lightweight fabric form is launched from Earth to be landed on the lunar surface and robotically filled with raw lunar regolith. In the materials testing program, regolith-bag fabric candidates included: Vectran(TM), Nextel(TM), Gore PTFE Fabric(TM), Zylon(TM), Twaron(TM), and Nomex(TM). Tensile (including post radiation exposure), fold, abrasion, and hypervelocity impact testing were performed under ambient conditions, and, within our current means, we also performed these tests under cold and elevated temperatures. In some cases, lunar simulant (JSC-1) was used in conjunction with testing. Our ambition is to continuously refine our testing to reach lunar environmental conditions to the extent possible. A series of preliminary structures were constructed during design of the final prototype. Design is based on the principles of the classic masonry arch. The prototype was constructed of Kevlar(TM) and filled with vermiculite (fairly close to the weight of lunar regolith on the moon). The structure is free-standing, but has not yet been load tested. Our plan for the future would be to construct higher fidelity mockups with each iteration, and to conduct appropriate tests of the structure.

Air bags and ocular injuries.

PubMed Central

Stein, J D; Jaeger, E A; Jeffers, J B

1999-01-01

PURPOSE: This investigation retrospectively examined ocular injuries associated with air bag deployment to gain a better appreciation of potential risk factors in motor vehicle accidents. National statistics regarding the efficacy of air bags were reviewed. METHODS: Review of the literature from 1991 to 1998 identified 44 articles describing 97 patients with air-bag-induced ocular injuries. Variables extracted from each case were age, sex, height, position in the car, eye wear, vehicle impact speed, visual acuity, and specific ocular injuries. RESULTS: Corneal abrasions occurred in 49% of occupants, hyphemas in 43%, vitreous or retinal hemorrhages in 25%, and retinal tears or detachments in 15%. The globe was ruptured in 10 patients. Patients involved in higher-speed accidents (over 30 mph) sustained a greater percentage of vitreous or retinal hemorrhages and traumatic cataracts, while those at slower speeds were more prone to retinal tears or detachments. In a subset of 14 patients with serious ocular injuries, the impact speed of 11 patients was recorded at 30 mph or less. Slower speed may be a risk factor for some ocular injuries. Occupant height was not a significant factor. National statistics confirm that air bags reduce fatalities in motor vehicle accidents. However, children sitting in the front seat without a seat belt and infants in passenger-side rear-facing car seats are at risk for fatal injury. CONCLUSION: Air bags combined with seat belts are an effective means of reducing injury and death in adults during motor vehicle accidents. However, this study has documented a wide variety of ocular injuries associated with air bag deployment. It is hoped that researchers can develop modifications that continue to save lives while minimizing additional harm. Images FIGURE 1 FIGURE 2A FIGURE 2B FIGURE 2C FIGURE 2D FIGURE 3A FIGURE 3B FIGURE 4 FIGURE 5 FIGURE 7 FIGURE 8 PMID:10703118

Workplace Exposure to Titanium Dioxide Nanopowder Released from a Bag Filter System

PubMed Central

Ji, Jun Ho; Kim, Jong Bum; Lee, Gwangjae; Noh, Jung-Hun; Yook, Se-Jin; Cho, So-Hye; Bae, Gwi-Nam

2015-01-01

Many researchers who use laboratory-scale synthesis systems to manufacture nanomaterials could be easily exposed to airborne nanomaterials during the research and development stage. This study used various real-time aerosol detectors to investigate the presence of nanoaerosols in a laboratory used to manufacture titanium dioxide (TiO2). The TiO2 nanopowders were produced via flame synthesis and collected by a bag filter system for subsequent harvesting. Highly concentrated nanopowders were released from the outlet of the bag filter system into the laboratory. The fractional particle collection efficiency of the bag filter system was only 20% at particle diameter of 100 nm, which is much lower than the performance of a high-efficiency particulate air (HEPA) filter. Furthermore, the laboratory hood system was inadequate to fully exhaust the air discharged from the bag filter system. Unbalanced air flow rates between bag filter and laboratory hood systems could result in high exposure to nanopowder in laboratory settings. Finally, we simulated behavior of nanopowders released in the laboratory using computational fluid dynamics (CFD). PMID:26125024

Bioregenerative system components for microgravity

NASA Technical Reports Server (NTRS)

Nevill, Gale E., Jr.; Hessel, Michael I., Jr.

1992-01-01

The goal of the class was to design, fabricate, and test prototype designs that were independent, yet applicable to a Closed Loop Life Support System. The three prototypes chosen were in the areas of agar plant growth, regnerative filtration, and microgravity food preparation. The plant growth group designed a prototype agar medium growth system that incorporates nutrient solution replenishment and post-harvest refurbishment. In addition, the unit emphasizes material containment and minimization of open interfaces. The second project was a filter used in microgravity that has the capability to clean itself. The filters are perforated plates which slide through a duct and are cleaned outside of the flow with a vacuum system. The air in the duct is prevented from flowing outside of the duct by a network of sliding seals. The food preparation group developed a device which dispenses and mixes ingredients and then cooks the mixture in microgravity. The dry ingredients are dispensed from a canister by a ratchet-operated piston. The wet ingredients are dispensed from plastic bags through tubing attached to a syringe. Once inside the mixing chamber, the ingredients are mixed using a collapsible whisk and then pushed into the cooking device.

SUSTAINABLE ANAEROBIC DIGESTER/COOK STOVE DESIGN TO PROMOTE HEALTH, ENVIRONMENT, AND ECONOMIC PROSPERITY FOR INDIGENOUS PEOPLE OF ECUADOR

EPA Science Inventory

Phase I prototype digesters demonstrated the feasibility of biogas generation, using simple materials such as trash cans, oil drums, and polyethylene bags – a full scale digester, based on prototype biogas production volumes, range from 5000 to 9000 liters, depending on ...

White blood cell counting system

NASA Technical Reports Server (NTRS)

1972-01-01

The design, fabrication, and tests of a prototype white blood cell counting system for use in the Skylab IMSS are presented. The counting system consists of a sample collection subsystem, sample dilution and fluid containment subsystem, and a cell counter. Preliminary test results show the sample collection and the dilution subsystems are functional and fulfill design goals. Results for the fluid containment subsystem show the handling bags cause counting errors due to: (1) adsorption of cells to the walls of the container, and (2) inadequate cleaning of the plastic bag material before fabrication. It was recommended that another bag material be selected.

Effect of air bags and restraining devices on the pattern of facial fractures in motor vehicle crashes.

PubMed

Simoni, Payman; Ostendorf, Robert; Cox, Artemus J

2003-01-01

To examine the relationship between the use of restraining devices and the incidence of specific facial fractures in motor vehicle crashes. Retrospective analysis of patients with facial fractures following a motor vehicle crash. University of Alabama at Birmingham Hospital level I trauma center from 1996 to 2000. Of 3731 patients involved in motor vehicle crashes, a total of 497 patients were found to have facial fractures as determined by International Classification of Diseases, Ninth Revision (ICD-9) codes. Facial fractures were categorized as mandibular, orbital, zygomaticomaxillary complex (ZMC), and nasal. Use of seat belts alone was more effective in decreasing the chance of facial fractures in this population (from 17% to 8%) compared with the use of air bags alone (17% to 11%). The use of seat belts and air bags together decreased the incidence of facial fractures from 17% to 5%. Use of restraining devices in vehicles significantly reduces the chance of incurring facial fractures in a severe motor vehicle crash. However, use of air bags and seat belts does not change the pattern of facial fractures greatly except for ZMC fractures. Air bags are least effective in preventing ZMC fractures. Improving the mechanics of restraining devices might be needed to minimize facial fractures.

[A new applicator with regulatable air bag designed for intracavitary brachytherapy of nasopharyngeal carcinoma].

PubMed

Zhang, Ning; Wei, Guang-Yu; Tan, Yi-Chang; Huang, Ze-Li; Li, Shao-En; Lu, Zhi-Qian

2004-10-01

Nasopharynx applicator used in intracavitary brachytherapy plays an important role in the radiotherapy of nasopharyngeal carcinoma (NPC), its quality affects the efficiency of treatment. This study was to design a new applicator for clinical use. An inexpensive, reusable, and flexible latex nasopharynx applicator was designed. An air bag was placed at 15 mm from the foreside of the applicator, clung to the tube. The edge of air bag is tangent to the axis of tube. When the bag was full of air, the tube would hunch reversely,close to nasopharyngeal vault. After introduced into nasopharynx through middle nasal meatus, the applicator could be fixed in suitable position by its rotation, and air bag regulation, and confirmed its position by simulation. A total of 221 patients with NPC were treated with external beam radiation therapy in our hospital, and boosted HDR brachytherapy using this new applicator. The response rate was 92.6% in the primary tumor group (200/216), and 100% in the recurrent tumor group (5/5). Mucosal necrosis in the posterior or anterior wall of nasopharynx occurred in 5 patients, 8 patients experienced nasal congestion and nasal synechia. This new nasopharynx applicator is easy to operate, painless, and well dosage-distributed. Mucosal necrosis is likely due to higher fractional dose.

Efficacy of humidity retention bags for the reduced adsorption and improved cleaning of tissue proteins including prion-associated amyloid to surgical stainless steel surfaces.

PubMed

Secker, T J; Pinchin, H E; Hervé, R C; Keevil, C W

2015-01-01

Increasing drying time adversely affects attachment of tissue proteins and prion-associated amyloid to surgical stainless steel, and reduces the efficacy of commercial cleaning chemistries. This study tested the efficacy of commercial humidity retention bags to reduce biofouling on surgical stainless steel and to improve subsequent cleaning. Surgical stainless steel surfaces were contaminated with ME7-infected brain homogenates and left to dry for 15 to 1,440 min either in air, in dry polythene bags or within humidity retention bags. Residual contamination pre/post cleaning was analysed using Thioflavin T/SYPRO Ruby dual staining and microscope analysis. An increase in biofouling was observed with increased drying time in air or in sealed dry bags. Humidity retention bags kept both protein and prion-associated amyloid minimal across the drying times both pre- and post-cleaning. Therefore, humidity bags demonstrate a cheap, easy to implement solution to improve surgical instrument reprocessing and to potentially reduce associated hospital acquired infections.

49 CFR 585.15 - Reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting Requirements § 585.15 Reporting requirements. (a) Advanced credit phase-in reporting... any of those production years as complying with phase one of the advanced air bag requirements of...

49 CFR 585.15 - Reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase-in Reporting Requirements § 585.15 Reporting requirements. (a) Advanced credit phase-in reporting... any of those production years as complying with phase one of the advanced air bag requirements of...

49 CFR 552.12 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Expedited Rulemaking To Establish Dynamic Automatic Suppression System Test Procedures for Federal Motor... subpart, the following definitions apply: (a) Dynamic automatic suppression system (DASS) means a portion of an air bag system that automatically controls whether or not the air bag deploys during a crash by...

Effect of Restraining Devices on Facial Fractures in Motor Vehicle Collisions.

PubMed

Hwang, Kun; Kim, Joo Ho

2015-09-01

The aim of this systematic review is to summarize and critically evaluate the evidence for or against the effectiveness of restraining devices on facial fractures in motor vehicle collisions (MVCs).In a PubMed search, the search terms "facial bone fracture and seat belt," "facial bone fracture and air bag," and "facial bone fracture and restraining" were used. The authors abstracted the odds ratio (OR) and 95% confidence intervals (CIs) from each study. Weighted mean differences and 95% CIs were also calculated. The statistical analysis was performed with Review Manager (The Nordic Cochrane Centre).The authors found 30 potentially relevant articles, of which 6 articles met our inclusion criteria. Five studies were subgrouped, and a meta-analysis of these data suggested beneficial effects of seat belts on decreasing facial fractures in MVCs (n = 15,768,960, OR, 0.46, 95% CI = 0.35-0.60). Three studies were subgrouped, and a meta-analysis of these data suggested that there were beneficial effects of seat belts and air bags on decreasing facial fractures in MVCs (n = 15,768,021, OR, 0.59, 95% CI = 0.47-0.74). Four studies were subgrouped, and a meta-analysis of these data suggested there were no significant effects of an air bag on decreasing facial fracture in MVCs (n = 15,932,259, OR, 1.00, 95% CI = 0.72-1.39).A seat belt alone (OR, 0.46) or a seat belt and an air bag (OR, 0.59) were effective to decrease facial fractures in MVCs. However, air bags alone had no significant effect (OR, 1.00). In using air bags, seat belt should be applied together to prevent facial fractures in motor vehicle injuries.

76 FR 60118 - Tesla Motors, Inc. Grant of Petition for Renewal of a Temporary Exemption From the Advanced Air...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-28

... can be considered to manufacture the Roadster. Lotus, based on its involvement in the design and..., requiring what are commonly known as ``advanced air bags.'' \\3\\ The upgrade was designed to meet the twin... effects of some air bag designs. This plan also included an extensive consumer education program to...

49 CFR 579.22 - Reporting requirements for manufacturers of 100 or more buses, manufacturers of 500 or more...

Code of Federal Regulations, 2013 CFR

2013-10-01

... visibility, 14 air bags, 15 seat belts, 16 structure, 17 latch, 18 vehicle speed control, 19 tires, 20 wheels... exterior lighting, 13 visibility, 14 air bags, 15 seat belts, 16 structure, 17 latch, 18 vehicle speed... of service brake system (i.e., hydraulic or air), the information required by this subsection shall...

The first survey of airborne trace elements at airport using moss bag technique.

PubMed

Vuković, Gordana; Urošević, Mira Aničić; Škrivanj, Sandra; Vergel, Konstantin; Tomašević, Milica; Popović, Aleksandar

2017-06-01

Air traffic represents an important way of social mobility in the world, and many ongoing discussions are related to the impacts that air transportation has on local air quality. In this study, moss Sphagnum girgensohnii was used for the first time in the assessment of trace element content at the international airport. The moss bags were exposed during the summer of 2013 at four sampling sites at the airport 'Nikola Tesla' (Belgrade, Serbia): runway (two), auxiliary runway and parking lot. According to the relative accumulation factor (RAF) and the limit of quantification of the moss bag technique (LOQ T ), the most abundant elements in the samples were Zn, Na, Cr, V, Cu and Fe. A comparison between the element concentrations at the airport and the corresponding values in different land use classes (urban central, suburban, industrial and green zones) across the city of Belgrade did not point out that the air traffic and associated activities significantly contribute to the trace element air pollution. This study emphasised an easy operational and robust (bio)monitoring, using moss bags as a suitable method for assessment of air quality within various microenvironments with restriction in positioning referent instrumental devices.

77 FR 69927 - Safety Advisory Notice: Safety Advisory for Shippers and Carriers of Air Bags

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-21

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket No... Air Bags AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: Safety... Administrator for Hazardous Materials Safety, Pipeline and Hazardous Materials Safety Administration. [FR Doc...

40 CFR 60.273 - Emission monitoring.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Inspecting the baghouse for air leaks, torn or broken bags or filter media, or any other condition that may....273 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... installs and continuously operates a bag leak detection system according to paragraph (e) of this section...

40 CFR 60.273 - Emission monitoring.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Inspecting the baghouse for air leaks, torn or broken bags or filter media, or any other condition that may....273 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... installs and continuously operates a bag leak detection system according to paragraph (e) of this section...

40 CFR 60.273a - Emission monitoring.

Code of Federal Regulations, 2013 CFR

2013-07-01

... following: (1) Inspecting the baghouse for air leaks, torn or broken bags or filter media, or any other....273a Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... by a certified visible emission observer and the owner installs and continuously operates a bag leak...

40 CFR 60.273 - Emission monitoring.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Inspecting the baghouse for air leaks, torn or broken bags or filter media, or any other condition that may....273 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... installs and continuously operates a bag leak detection system according to paragraph (e) of this section...

40 CFR 60.273a - Emission monitoring.

Code of Federal Regulations, 2014 CFR

2014-07-01

... following: (1) Inspecting the baghouse for air leaks, torn or broken bags or filter media, or any other....273a Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... by a certified visible emission observer and the owner installs and continuously operates a bag leak...

40 CFR 60.273a - Emission monitoring.

Code of Federal Regulations, 2012 CFR

2012-07-01

... following: (1) Inspecting the baghouse for air leaks, torn or broken bags or filter media, or any other....273a Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... by a certified visible emission observer and the owner installs and continuously operates a bag leak...

Collecting apparatus

DOEpatents

Duncan, Charles P.

1983-01-01

An improved collecting apparatus for small aquatic or airborne organisms such as plankton, larval fish, insects, etc. The improvement constitutes an apertured removal container within which is retained a collecting bag, and which is secured at the apex of a conical collecting net. Such collectors are towed behind a vessel or vehicle with the open end of the conical net facing forward for trapping the aquatic or airborne organisms within the collecting bag, while allowing the water or air to pass through the apertures in the container. The container is readily removable from the collecting net whereby the collecting bag can be quickly removed and replaced for further sample collection. The collecting bag is provided with means for preventing the bag from being pulled into the container by the water or air flowing therethrough.

Significant air embolism: A possibility even with collapsible intravenous fluid containers when used with rapid infuser system

PubMed Central

Pant, Deepanjali; Narani, Krishan Kumar; Sood, Jayashree

2010-01-01

Significant venous air embolism may develop acutely during the perioperative period due to a number of causes such as during head and neck surgery, spinal surgery, improper central venous and haemodialysis catheter handling, etc. The current trend of using self collapsible intravenous (IV) infusion bags instead of the conventional glass or plastic bottles has several advantages, one of thaem being protection against air embolism. We present a 56-year-old man undergoing kidney transplantation, who developed a near fatal venous air embolism during volume resuscitation with normal saline in collapsible IV bags used with rapid infuser system. To our knowledge, this problem with collapsible infusion bags has not been reported earlier. PMID:20532073

49 CFR 579.22 - Reporting requirements for manufacturers of 100 or more buses, manufacturers of 500 or more...

Code of Federal Regulations, 2014 CFR

2014-10-01

... train, 11 electrical, 12 exterior lighting, 13 visibility, 14 air bags, 15 seat belts, 16 structure, 17... visibility, 14 air bags, 15 seat belts, 16 structure, 17 latch, 18 vehicle speed control, 19 tires, 20 wheels... manufactured and available with more than one type of service brake system (i.e., hydraulic or air), the...

Experimental impact protection with advanced restraint systems : preliminary primate with air bag and inertia reel/inverted-y yoke torso harness.

DOT National Transportation Integrated Search

1969-02-01

Both the inverted-Y yoke torso harness with inertia reel and the air- bag restraint system have had extensive independent development for some time by several engineering and research organizations for both aviation and ground vehicle occupant protec...

Cost analysis of the Mercedes-Benz occupant detection system for air bag shut-off

DOT National Transportation Integrated Search

1997-04-01

The objective of this project is to develop the variable manufacturing costs and lead time estimates of an "occupant detection system for air bag shut off". The Mercedes-Benz system was used as a base for developing this data. The system consists of ...

Fragmentation dynamics in the droplet bag breakup regime

NASA Astrophysics Data System (ADS)

Kulkarni, Varun; Sojka, Paul

2014-11-01

The closing stages of a droplet bag breakup event is marked by the appearance of several topological changes in the drop shape, followed by its fragmentation owing to hydrodynamics instabilities. In the present work we examine this breakup event, which occurs when a drop enters a continuous jet air stream. The deformed drop before eventual fragmentation is comprised of two main features: a bag and a bounding rim. Our investigation discusses the mechanism of rim/ bag breakup and the ensuing drop size distribution. The role of two possible instabilities, Plateau -Rayleigh and Rayleigh -Taylor, in rim breakup is examined and the dominant role of the Plateau -Rayleigh instability is revealed. In contrast, the Rayleigh -Taylor instability is seen to explain the disintegration of the bag well. The effects of viscosity and air jet velocity are also investigated. The formation of secondary features, such as nodes on the rim and holes on the bag, are also discussed. To conclude, a simple scaling argument based on the characteristic time scales of these instabilities is presented to explain the commonly observed early bursting of the bag, vis-à-vis the rim.

Inflatable stretcher to transport patients

NASA Technical Reports Server (NTRS)

Clark, C. C.; Gordon, F. T., Jr.; Schmidt, C. B.

1970-01-01

Inflatable plastic bag inside strong, inflexible outer bag facilitates emergency transport of seriously burned or disabled patients. When the bag is inflated the patient is completely immobilized and cushioned from external shock. Air for breathing, temperature controls and communications may be provided by appropriate plug-in connections.

Bio-active glass air-abrasion has the potential to remove resin composite restorative material selectively

NASA Astrophysics Data System (ADS)

Milly, Hussam; Andiappan, Manoharan; Thompson, Ian; Banerjee, Avijit

2014-06-01

The aims of this study were to assess: (a) the chemistry, morphology and bioactivity of bio-active glass (BAG) air-abrasive powder, (b) the effect of three air-abrasion operating parameters: air pressure, powder flow rate (PFR) and the abrasive powder itself, on the selective removal of resin composite and (c) the required "time taken". BAG abrasive particles were characterised using scanning electron microscopy-energy dispersive X-ray spectrometry (SEM-EDX) and Fourier-transform infrared spectroscopy (FTIR). Standardised resin composite restorations created within an enamel analogue block (Macor™) in vitro, were removed using air-abrasion undersimulated clinical conditions. 90 standardised cavities were scanned before and after resin composite removal using laser profilometry and the volume of the resulting 3D images calculated. Multilevel linear model was used to identify the significant factors affecting Macor™ removal. BAG powder removed resin composite more selectively than conventional air-abrasion alumina powder using the same operating parameters (p < 0.001) and the effect of altering the unit's operating parameters was significant (p < 0.001). In conclusion, BAG powder is more efficient than alumina in the selective removal of resin composite particularly under specific operating parameters, and therefore may be recommended clinically as a method of preserving sound enamel structure when repairing and removing defective resin composite restorations.

Comparison of storage stability of odorous VOCs in polyester aluminum and polyvinyl fluoride Tedlar® bags.

PubMed

Kim, Yong-Hyun; Kim, Ki-Hyun; Jo, Sang-Hee; Jeon, Eui-Chan; Sohn, Jong Ryeul; Parker, David B

2012-01-27

Whole air sampling using containers such as flexible bags or rigid canisters is commonly used to collect samples of volatile organic compounds (VOC) in air. The objective of this study was to compare the stability of polyester aluminum (PEA) and polyvinyl fluoride (PVF, brand name Tedlar(®)) bags for gaseous VOC sampling. Eight VOC standards (benzene, toluene, p-xylene, styrene, methyl ethyl ketone, methyl isobutyl ketone, butyl acetate, and isobutyl alcohol) were placed into each bag at storage times of 0, 2, and 3 days prior to analyses by gas chromatography/mass spectrometry (GC/MS). From each bag representing each storage day, samples of 3 different mass loadings were withdrawn and analyzed to derive response factors (RF) of each chemical between the slope of the GC response (y-axis) vs. loaded mass (x-axis). The relative recoveries (RR) of VOC, if derived by dividing RF value of a given storage day by that of 0 day, varied by time, bag type, and VOC type. If the RR values after three days are compared, those of methyl isobutyl ketone were the highest with 96 (PVF) and 99% (PEA); however, the results of isobutyl alcohol were highly contrasting between the two bags with 31 and 94%, respectively. Differences in RR values between the two bag types increased with storage time, such that RR of PEA bags (88±10%) were superior to those of PVF bags (73±22%) after three days, demonstrating that VOC in PEA bags were more stable than in PVF bags. Copyright © 2011 Elsevier B.V. All rights reserved.

40 CFR 60.51c - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF... Incinerators for Which Construction is Commenced After June 20, 1996 § 60.51c Definitions. Bag leak detection... order to detect bag failures. A bag leak detection system includes, but is not limited to, an instrument...

40 CFR 60.51c - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF... Incinerators for Which Construction is Commenced After June 20, 1996 § 60.51c Definitions. Bag leak detection... order to detect bag failures. A bag leak detection system includes, but is not limited to, an instrument...

A Hybrid Computing Testbed for Mobile Threat Detection and Enhanced Research and Education in Information

DTIC Science & Technology

2014-11-20

techniques to defend against stealthy malware, i.e., rootkits. For example, we have been developing new virtualization-based security service called AirBag ...for mobile devices. AirBag is a virtualization-based system that enables dynamic switching of (guest) Android im- ages in one VM, with one image

STS 31 PAYLOAD HUBBLE SPACE TELESCOPE ENCLOSED IN AN AIR-TIGHT PLASTIC BAG FOR PROTECTION IN VERTICA

NASA Technical Reports Server (NTRS)

1989-01-01

Preparations are made to enclose the Hubble Space Telescope [HST] inside an air-tight plastic bag in the VPF. Processing of the 94- inch primary mirror telescope for launch on the Discovery in March 1990, involves working within strict controls to prevent contamination.

76 FR 74708 - National Emission Standards for Hazardous Air Pollutants for Source Categories

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-01

... as follows: Bag leak detection system means a monitoring device for a fabric filter that identifies an increase in particulate matter emissions resulting from a broken filter bag or other malfunction... thermoset a binder on the mineral wool fiber used to make bonded products. Fabric filter means an air...

Inexpensive Dramatic Pneumatic Lift

ERIC Educational Resources Information Center

Morse, Robert A.

2017-01-01

Various experiments and demonstrations relate air pressure and air pressure difference to force and area. Carpenter and Minnix describe a large-scale pneumatic lift in which a person sitting on a board atop a plastic garbage bag is lifted when the bag is connected to the exhaustport of a vacuum cleaner, which easily lifts the person. This article…

49 CFR 552.14 - Content of petition.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of the DASS by moving a test device toward the driver air bag in a manner that simulates the motion... motion of an unbelted occupant during pre-crash braking or other pre-crash maneuver. The petitioner shall... logic, the system reaction time, the time duration used to evaluate whether the air bag should be...

49 CFR 552.14 - Content of petition.

Code of Federal Regulations, 2010 CFR

2010-10-01

... of the DASS by moving a test device toward the driver air bag in a manner that simulates the motion... motion of an unbelted occupant during pre-crash braking or other pre-crash maneuver. The petitioner shall... logic, the system reaction time, the time duration used to evaluate whether the air bag should be...

49 CFR 173.166 - Air bag inflators, air bag modules and seat-belt pretensioners.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., pyrotechnic for technical purposes” as specified in Special Provision 161 (see § 172.102 of this subchapter... Class 9 material. (4) Shipments to recycling or waste disposal facilities. When offered for domestic...) of this section. However, when these articles are shipped to a recycling facility, the word “Recycled...

49 CFR 173.166 - Air bag inflators, air bag modules and seat-belt pretensioners.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., pyrotechnic for technical purposes” as specified in Special Provision 161 (see § 172.102 of this subchapter... Class 9 material. (4) Shipments to recycling or waste disposal facilities. When offered for domestic...) of this section. However, when these articles are shipped to a recycling facility, the word “Recycled...

77 FR 48492 - Event Data Recorders

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-14

... that [cir] Involve side or side curtain/tube air bags such that EDR data would only need to be locked... deployable restraints other than frontal, side or side/curtain air bags such that EDR data would not need to.... The final rule was intended to be technology-neutral, so as to permit compliance with any available...

40 CFR 60.5225 - What are the monitoring and calibration requirements for compliance with my operating limits?

Code of Federal Regulations, 2014 CFR

2014-07-01

... limited to the following: (i) Inspecting the fabric filter for air leaks, torn or broken bags or filter... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY... maintain your bag leak detection system in continuous operation according to your monitoring plan required...

40 CFR 62.14690 - What monitoring equipment must I install and what parameters must I monitor?

Code of Federal Regulations, 2012 CFR

2012-07-01

... each baghouse compartment or cell. For negative pressure or induced air fabric filters, the bag leak... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS... subpart, you must install, calibrate, maintain, and continuously operate a bag leak detection system as...

40 CFR 60.5225 - What are the monitoring and calibration requirements for compliance with my operating limits?

Code of Federal Regulations, 2013 CFR

2013-07-01

... limited to the following: (i) Inspecting the fabric filter for air leaks, torn or broken bags or filter... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY... maintain your bag leak detection system in continuous operation according to your monitoring plan required...

40 CFR 62.14690 - What monitoring equipment must I install and what parameters must I monitor?

Code of Federal Regulations, 2014 CFR

2014-07-01

... each baghouse compartment or cell. For negative pressure or induced air fabric filters, the bag leak... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS... subpart, you must install, calibrate, maintain, and continuously operate a bag leak detection system as...

40 CFR 62.14690 - What monitoring equipment must I install and what parameters must I monitor?

Code of Federal Regulations, 2013 CFR

2013-07-01

... each baghouse compartment or cell. For negative pressure or induced air fabric filters, the bag leak... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS... subpart, you must install, calibrate, maintain, and continuously operate a bag leak detection system as...

Modeling and Simulation of the Second-Generation Orion Crew Module Air Bag Landing System

NASA Technical Reports Server (NTRS)

Timmers, Richard B.; Hardy, Robin C.; Willey, Cliff E.; Welch, Joseph V.

2009-01-01

Air bags were evaluated as the landing attenuation system for earth landing of the Orion Crew Module (CM). Analysis conducted to date shows that airbags are capable of providing a graceful landing of the CM in nominal and off-nominal conditions such as parachute failure, high horizontal winds, and unfavorable vehicle/ground angle combinations, while meeting crew and vehicle safety requirements. The analyses and associated testing presented here surround a second generation of the airbag design developed by ILC Dover, building off of relevant first-generation design, analysis, and testing efforts. In order to fully evaluate the second generation air bag design and correlate the dynamic simulations, a series of drop tests were carried out at NASA Langley s Landing and Impact Research (LandIR) facility in Hampton, Virginia. The tests consisted of a full-scale set of air bags attached to a full-scale test article representing the Orion Crew Module. The techniques used to collect experimental data, develop the simulations, and make comparisons to experimental data are discussed.

40 CFR 86.1340-94 - Exhaust sample analysis.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Section 86.1340-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... (except diesels), CH4 (natural gas-fueled engines only), CO, CO2. and NOX sample bag(s) with approximately... not require bag analysis.) (d)(8) through (h) [Reserved]. For guidance see § 86.1340-90. [59 FR 48534...

40 CFR 86.1340-94 - Exhaust sample analysis.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 86.1340-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... (except diesels), CH4 (natural gas-fueled engines only), CO, CO2. and NOX sample bag(s) with approximately... not require bag analysis.) (d)(8) through (h) [Reserved]. For guidance see § 86.1340-90. [59 FR 48534...

40 CFR 86.1340-94 - Exhaust sample analysis.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Section 86.1340-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... (except diesels), CH4 (natural gas-fueled engines only), CO, CO2. and NOX sample bag(s) with approximately... not require bag analysis.) (d)(8) through (h) [Reserved]. For guidance see § 86.1340-90. [59 FR 48534...

40 CFR 86.1340-94 - Exhaust sample analysis.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Section 86.1340-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... (except diesels), CH4 (natural gas-fueled engines only), CO, CO2. and NOX sample bag(s) with approximately... not require bag analysis.) (d)(8) through (h) [Reserved]. For guidance see § 86.1340-90. [59 FR 48534...

75 FR 51870 - Wheego Electric Cars, Inc.; Receipt of Application for Temporary Exemption From Advanced Air Bag...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

...-0118] Wheego Electric Cars, Inc.; Receipt of Application for Temporary Exemption From Advanced Air Bag... with the procedures in 49 CFR part 555, Wheego Electric Cars, Inc., has petitioned the agency for a... requirements submitted by a manufacturer of a small electric car. II. Overview of Wheego's Petition for...

STS-32 OV-102 air revitalization system (ARS) humidity separator problem

NASA Image and Video Library

1990-01-20

During STS-32, onboard Columbia, Orbiter Vehicle (OV) 102, a leakage problem at environmental control and life support system (ECLSS) air revitalization system (ARS) humidity separator A below the middeck is solved with a plastic bag and a towel. The towel inserted inside a plastic bag absorbed the water that had collected at the separator inlet.

STS-32 OV-102 air revitalization system (ARS) humidity separator problem

NASA Technical Reports Server (NTRS)

1990-01-01

During STS-32, onboard Columbia, Orbiter Vehicle (OV) 102, a leakage problem at environmental control and life support system (ECLSS) air revitalization system (ARS) humidity separator A below the middeck is solved with a plastic bag and a towel. The towel inserted inside a plastic bag absorbed the water that had collected at the separator inlet.

76 FR 73010 - Technical Report Evaluating the 1999-2003 Head Impact Upgrade of FMVSS No. 201, Upper-Interior...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-28

...-Interior Components: Effectiveness of Energy-Absorbing Materials Without Head-Protection Air Bags. DATES... Reporting System--Multiple Cause of Death files for 1999-2007. FMVSS No. 201 without head-protection air bags reduces AIS 4-to-6 head injuries due to contact with upper-interior components by an estimated 24...

Launching Garbage-Bag Balloons.

ERIC Educational Resources Information Center

Kim, Hy

1997-01-01

Presents a modification of a procedure for making and launching hot air balloons made out of garbage bags. Student instructions for balloon construction, launching instructions, and scale diagrams are included. (DDR)

Automatic classification and detection of clinically relevant images for diabetic retinopathy

NASA Astrophysics Data System (ADS)

Xu, Xinyu; Li, Baoxin

2008-03-01

We proposed a novel approach to automatic classification of Diabetic Retinopathy (DR) images and retrieval of clinically-relevant DR images from a database. Given a query image, our approach first classifies the image into one of the three categories: microaneurysm (MA), neovascularization (NV) and normal, and then it retrieves DR images that are clinically-relevant to the query image from an archival image database. In the classification stage, the query DR images are classified by the Multi-class Multiple-Instance Learning (McMIL) approach, where images are viewed as bags, each of which contains a number of instances corresponding to non-overlapping blocks, and each block is characterized by low-level features including color, texture, histogram of edge directions, and shape. McMIL first learns a collection of instance prototypes for each class that maximizes the Diverse Density function using Expectation- Maximization algorithm. A nonlinear mapping is then defined using the instance prototypes and maps every bag to a point in a new multi-class bag feature space. Finally a multi-class Support Vector Machine is trained in the multi-class bag feature space. In the retrieval stage, we retrieve images from the archival database who bear the same label with the query image, and who are the top K nearest neighbors of the query image in terms of similarity in the multi-class bag feature space. The classification approach achieves high classification accuracy, and the retrieval of clinically-relevant images not only facilitates utilization of the vast amount of hidden diagnostic knowledge in the database, but also improves the efficiency and accuracy of DR lesion diagnosis and assessment.

78 FR 39062 - Group Lotus plc; Modification of a Temporary Exemption From an Advanced Air Bag Requirement of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-28

...-0086] Group Lotus plc; Modification of a Temporary Exemption From an Advanced Air Bag Requirement of... temporary exemption granted to Group Lotus plc (Lotus) on March 8, 2013. The agency granted Lotus an... Lotus Plc (Lotus) a temporary exemption from the higher maximum speed (56 km/h (35 mph)) belted test...

76 FR 7898 - Wheego Electric Cars, Inc.; Grant of Application for Temporary Exemption From Advanced Air Bag...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-11

...-0118] Wheego Electric Cars, Inc.; Grant of Application for Temporary Exemption From Advanced Air Bag... grants the petition of Wheego Electric Cars, Inc. (Wheego) for the temporary exemption of its Whip LiFe... manufacturer of a plug-in electric car. The stated basis of the petition was that requiring compliance would...

Identification of control parameters for the sulfur gas storability with bag sampling methods

USDA-ARS?s Scientific Manuscript database

Air samples containing sulfur compounds are often collected and stored in sample bags prior to analyses. The storage stability of six gaseous sulfur compounds (H2S, CH3SH, DMS, CS2, DMDS and SO2) was compared between two different bag materials (polyvinyl fluoride (PVF) and polyester aluminum (PEA))...

Improved Helium-Barrier Bag

NASA Technical Reports Server (NTRS)

Viger, Brent J.; Logan, Robert F.; Fink, Jeffrey E.

1992-01-01

Specially designed bag maintains helium atmosphere around large, low-temperature duct. Easy to install, durable, and reusable. Intended to prevent cryopumping occurring if air or nitrogen allowed to make contact with cold surface of duct.

A dual mode breath sampler for the collection of the end-tidal and dead space fractions.

PubMed

Salvo, P; Ferrari, C; Persia, R; Ghimenti, S; Lomonaco, T; Bellagambi, F; Di Francesco, F

2015-06-01

This work presents a breath sampler prototype automatically collecting end-tidal (single and multiple breaths) or dead space air fractions (multiple breaths). This result is achieved by real time measurements of the CO2 partial pressure and airflow during the expiratory and inspiratory phases. Suitable algorithms, used to control a solenoid valve, guarantee that a Nalophan(®) bag is filled with the selected breath fraction even if the subject under test hyperventilates. The breath sampler has low pressure drop (<0.5 kPa) and uses inert or disposable components to avoid bacteriological risk for the patients and contamination of the breath samples. A fully customisable software interface allows a real time control of the hardware and software status. The performances of the breath sampler were evaluated by comparing (a) the CO2 partial pressure calculated during the sampling with the CO2 pressure measured off-line within the Nalophan(®) bag; (b) the concentrations of four selected volatile organic compounds in dead space, end-tidal and mixed breath fractions. Results showed negligible deviations between calculated and off-line CO2 pressure values and the distributions of the selected compounds into dead space, end-tidal and mixed breath fractions were in agreement with their chemical-physical properties. Copyright © 2015. Published by Elsevier Ltd.

[Injuries to car passengers protected by air bags].

PubMed

Sefrin, P; Kuhnigk, H; Koburg, R

2004-11-01

The air bag, like the seatbelt, is a further development of the inside protection of motorcar passengers. However, the airbag has also been made responsible for severe internal injuries. In a retrospective case control study, 394 accidents in which the air bag was released were analysed. At least medium severe injuries (Maximum Abbreviated Injury Scale: MAIS > or = 2) occurred in 69 cases. Three different patterns of injury were distinguished depending on the level of difficulty of diagnosis by the emergency physician. Damage to the vehicles was scored in five intensities or damage grades. Thoracic injury was most frequently diagnosed in the patients (in 61.5 % of cases), followed by injuries to the lower (50.8 %) and upper extremities (47.7 %). Single injuries with a grade of severity of 2 (MAIS) predominated (59.7 %). In most of the cases the injury was easy to diagnose (64.6 %) because of external signs, in 24.6 % internal injuries were assumed and in only 10.8 % were there no sings of damage to body cavities. Most frequent were occult injuries in the thoracic region (100 %) and in the abdomen (74.4 %). However, occult injuries did not always conform to the grade of deformation to the vehicle, since in 66.7 % the grade of damage was 3. This was not true for the remaining types of injury because external injuries increased with the grade of damage to the vehicle. After the release of the air bag, occult injuries of the body cavities have to be expected, even if there are no signs of external injury. Women under 35 years of age are particularly endangered. There exists no minimum velocity for the occurrence of injuries to the body cavities because harm can simply be a result of the release of the air bag.

14. BUILDING NO. 445, PHYSICS LAB (FORMERLY GUN BAG LOADING), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. BUILDING NO. 445, PHYSICS LAB (FORMERLY GUN BAG LOADING), LOOKING EAST AT SOUTHWEST END OF BUILDING. HVAC EQUIPMENT LOCATED OUTDOORS IN FOREGROUND. DUCTS CONDUCT HOT OR COLD AIR INDOORS. ROUND PIPES ARE INSULATED STEAM LINES. BUILDING NO. 448, ORDNANCE FACILITY, IN BACKGROUND. - Picatinny Arsenal, 400 Area, Gun Bag Loading District, State Route 15 near I-80, Dover, Morris County, NJ

A New Fast, Reliable Technique for the Sampling of Dissolved Inorganic Carbon in Sea Ice

NASA Astrophysics Data System (ADS)

Hu, Y.; Wang, F.; Rysgaard, S.; Barber, D. G.

2015-12-01

For a long time, sea ice was considered to act as a lid over seawater preventing CO2 exchange between the atmosphere and ocean. Recent observations suggest that sea ice can be an active source or a sink for CO2, although its magnitude is not very clear. The direct measurements on CO2 flux based on the chamber method and eddy covariance often do not agree with each other. It is therefore important to measure the dissolved inorganic carbon (DIC) stock in sea ice precisely in order to better understand the CO2 flux through sea ice. The challenges in sea ice DIC sampling is how to melt the ice core without being exposed to the air gaining or losing CO2. A common practice is to seal the ice core in a self-prepared gas-tight plastic bag and suck the air out of the bag gently using a syringe (together with a needle) through a valve mounted on one side of the bag. However, this method is time consuming (takes up to several minutes to suck the air out) and very often there is large headspace found in the bag after the ice melts due to the imperfect bag-preparation, which might affect the DIC concentration in melt ice-water. We developed a new technique by using a commercially available plastic bag with a vacuum sealer to seal the ice core. In comparison to syringe-based method, this technique is fast and easy to operate; it takes less than 10 seconds to vacuum and seal the bag all in one button with no headspace left in the bag. Experimental tests with replicate ice cores sealed by those two methods showed that there is no difference in the DIC concentration measured after these two methods, suggesting that there is no loss of DIC during the course of vacuum sealing. In addition, a time series experiment on DIC in melt ice-water stored in the new bag shows that when the samples were not poisoned, the DIC concentration remains unchanged for at least 3 days in the bag; while poisoned by HgCl2, there is no change in DIC for at least 21 days, indicating that this new bag is impermeable to CO2. Therefore, this new technique offers a convenient yet reliable method for DIC sampling of sea ice.

Stability of odorants from pig production in sampling bags for olfactometry.

PubMed

Hansen, Michael J; Adamsen, Anders P S; Feilberg, Anders; Jonassen, Kristoffer E N

2011-01-01

Odor from pig production facilities is typically measured with olfactometry, whereby odor samples are collected in sampling bags and assessed by human panelists within 30 h. In the present study, the storage stability of odorants in two types of sampling bags that are often used for olfactometry was investigated. The bags were made of Tedlar or Nalophan. In a field experiment, humid and dried air samples were collected from a pig production facility with growing-finishing pigs and analyzed with a gas chromatograph with an amperometric sulfur detector at 4, 8, 12, 28, 52, and 76 h after sampling. In a laboratory experiment, the bags were filled with a humid gas mixture containing carboxylic acids, phenols, indoles, and sulfur compounds and analyzed with proton-transfer-reaction mass spectrometry after 0, 4, 8, 12, and 24 h. The results demonstrated that the concentrations of carboxylic acids, phenols, and indoles decreased by 50 to >99% during the 24 h of storage in Tedlar and Nalophan bags. The concentration of hydrogen sulfide decreased by approximately 30% during the 24 h of storage in Nalophan bags, whereas in Tedlar bags the concentration of sulfur compounds decreased by <5%. In conclusion, the concentrations of odorants in air samples from pig production facilities significantly decrease during storage in Tedlar and Nalophan bags, and the composition changes toward a higher relative presence of sulfur compounds. This can result in underestimation of odor emissions from pig production facilities and of the effect of odor reduction technologies. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Evaluation of sample recovery of malodorous livestock gases from air sampling bags, solid-phase microextraction fibers, Tenax TA sorbent tubes, and sampling canisters.

PubMed

Koziel, Jacek A; Spinhirne, Jarett P; Lloyd, Jenny D; Parker, David B; Wright, Donald W; Kuhrt, Fred W

2005-08-01

Odorous gases associated with livestock operations are complex mixtures of hundreds if not thousands of compounds. Research is needed to know how best to sample and analyze these compounds. The main objective of this research was to compare recoveries of a standard gas mixture of 11 odorous compounds from the Carboxen/PDMS 75-microm solid-phase microextraction fibers, polyvinyl fluoride (PVF; Tedlar), fluorinated ethylene propylene copolymer (FEP; Teflon), foil, and polyethylene terephthalate (PET; Melinex) air sampling bags, sorbent 2,b-diphenylene-oxide polymer resin (Tenax TA) tubes, and standard 6-L Stabilizer sampling canisters after sample storage for 0.5, 24, and 120 (for sorbent tubes only) hrs at room temperature. The standard gas mixture consisted of 7 volatile fatty acids (VFAs) from acetic to hexanoic, and 4 semivolatile organic compounds including p-cresol, indole, 4-ethylphenol, and 2'-aminoacetophenone with concentrations ranging from 5.1 ppb for indole to 1270 ppb for acetic acid. On average, SPME had the highest mean recovery for all 11 gases of 106.2%, and 98.3% for 0.5- and 24-hr sample storage time, respectively. This was followed by the Tenax TA sorbent tubes (94.8% and 88.3%) for 24 and 120 hr, respectively; PET bags (71.7% and 47.2%), FEP bags (75.4% and 39.4%), commercial Tedlar bags (67.6% and 22.7%), in-house-made Tedlar bags (47.3% and 37.4%), foil bags (16.4% and 4.3%), and canisters (4.2% and 0.5%), for 0.5 and 24 hr, respectively. VFAs had higher recoveries than semivolatile organic compounds for all of the bags and canisters. New FEP bags and new foil bags had the lowest and the highest amounts of chemical impurities, respectively. New commercial Tedlar bags had measurable concentrations of N,N-dimethyl acetamide and phenol. Foil bags had measurable concentrations of acetic, propionic, butyric, valeric, and hexanoic acids.

Testing odorants recovery from a novel metallized fluorinated ethylene propylene gas sampling bag.

PubMed

Zhu, Wenda; Koziel, Jacek A; Cai, Lingshuang; Wright, Donald; Kuhrt, Fred

2015-12-01

Industry-standard Tedlar bags for odor sample collection from confined animal feeding operations (CAFOs) have been challenged by the evidence of volatile organic compound (VOC) losses and background interferences. Novel impermeable aluminum foil with a thin layer of fluorinated ethylene propylene (FEP) film on the surface that is in contact with a gas sample was developed to address this challenge. In this research, Tedlar and metallized FEP bags were compared for (a) recoveries of four characteristic CAFO odorous VOCs (ethyl mercaptan, butyric acid, isovaleric acid and p-cresol) after 30 min and 24 hr sample storage time and for (b) chemical background interferences. All air sampling and analyses were performed with solid-phase microextraction (SPME) followed by gas chromatography-mass spectroscopy (GC-MS). Mean target gas sample recoveries from metallized FEP bags were 25.9% and 28.0% higher than those in Tedlar bags, for 30 min and 24 hr, respectively. Metallized FEP bags demonstrated the highest p-cresol recoveries after 30-min and 24-hr storage, 96.1±44.5% and 44.8±10.2%, respectively, among different types of sampling bags reported in previous studies. However, a higher variability was observed for p-cresol recovery with metallized FEP bags. A 0% recovery of ethyl mercaptan was observed with Tedlar bags after 24-hr storage, whereas an 85.7±7.4% recovery was achieved with metallized FEP bags. Recoveries of butyric and isovaleric acids were similar for both bag types. Two major impurities in Tedlar bags' background were identified as N,N-dimethylacetamide and phenol, while backgrounds of metallized FEP bags were significantly cleaner. Reusability of metallized FEP bags was tested. Caution is advised when using polymeric materials for storage of livestock-relevant odorous volatile organic compounds. The odorants loss with storage time confirmed that long-term storage in whole-air form is ill advised. A focused short-term odor sample containment should be biased toward the most inert material available relative to the highest impact target odorant. Metallized FEP was identified as such a material to p-cresol as the highest impact odorant from confined animal feeding operations. Metallized FEP bags have much cleaner background than commercial Tedlar bags do. Significantly higher recoveries of methyl mercaptan and p-cresol were also observed with metallized FEP bags.

Inexpensive Dramatic Pneumatic Lift

NASA Astrophysics Data System (ADS)

Morse, Robert A.

2017-09-01

Various experiments and demonstrations relate air pressure and air pressure difference to force and area. Carpenter and Minnix describe a large-scale pneumatic lift in which a person sitting on a board atop a plastic garbage bag is lifted when the bag is connected to the exhaustport of a vacuum cleaner, which easily lifts the person. This article describes the construction and use of an inexpensive hand-held pneumatic lift to demonstrate the same principle.

A first response bag with standardized contents for medical emergencies on cruise ships.

PubMed

Dahl, Eilif; Diskin, Art; Giusti, Angela C; Bilé, Anne; Williams, Steve

2010-01-01

There are no international rules regarding which medical supplies to bring when the nurseon- duty is called to emergencies outside a cruise ship's infirmary. Ideally, one First Response Bag should contain all that is needed to manage the initial 10-15 minutes of any medical emergency until the patient can be safely transported to the ship's infirmary. Royal Caribbean Cruises Ltd recently decided to establish a fleet-wide standardized First Response Bag for initial management of cardiac and other emergencies encountered by the nurse-on-duty outside the ship's infirmary. A prototype First Response Bag was tried out on one ship. A PowerPoint presentation of the bag with its contents was then circulated by e-mail to all 33 infirmaries of the fleet, and comments from all 181 medical staff members were invited. All responses were discussed fleet-wide for consensus. Responses from 18 ships triggered eager discussions. The resulting First Response Bag was considered by all an improvement compared to the solutions practiced previously on most ships of the fleet. The bag is a lightweight combined roller and backpack with 12 compartments, and it has well-organized, easily accessible, fleet-wide standardized minimal supplies. It contains what is needed to manage the initial phase of a cardiac arrest and other emergencies. This initiative may inspire other companies in standardization efforts and trigger cruise industry-wide cooperation'with the ultimate goal of an internationally accepted first response bag standard.

Suited Contingency Ops Food - 2

NASA Technical Reports Server (NTRS)

Glass, J. W.; Leong, M. L.; Douglas, G. L.

2014-01-01

The contingency scenario for an emergency cabin depressurization event may require crewmembers to subsist in a pressurized suit for up to 144 hours. This scenario requires the capability for safe nutrition delivery through a helmet feed port against a 4 psi pressure differential to enable crewmembers to maintain strength and cognition to perform critical tasks. Two nutritional delivery prototypes were developed and analyzed for compatibility with the helmet feed port interface and for operational effectiveness against the pressure differential. The bag-in-bag (BiB) prototype, designed to equalize the suit pressure with the beverage pouch and enable a crewmember to drink normally, delivered water successfully to three different subjects in suits pressurized to 4 psi. The Boa restrainer pouch, designed to provide mechanical leverage to overcome the pressure differential, did not operate sufficiently. Guidelines were developed and compiled for contingency beverages that provide macro-nutritional requirements, a minimum one-year shelf life, and compatibility with the delivery hardware. Evaluation results and food product parameters have the potential to be used to improve future prototype designs and develop complete nutritional beverages for contingency events. These feeding capabilities would have additional use on extended surface mission EVAs, where the current in-suit drinking device may be insufficient.

24. BUILDING NO. 452, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. BUILDING NO. 452, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), INTERIOR VIEW LOOKING WEST AT NORTH END OF CENTRAL CORRIDOR (ROOM 3). STAIRWAY WORKBENCH WITH COMPRESSED-AIR POWERED CARTRIDGE LOADER. ARMORED PASS-THROUGH OF TRANSFER BOX FOR PASSING EXPLOSIVES MATERIALS THROUGH TO NEXT ROOM TO THE NORTH. - Picatinny Arsenal, 400 Area, Gun Bag Loading District, State Route 15 near I-80, Dover, Morris County, NJ

Comparative efficacy of storage bags, storability and damage potential of bruchid beetle.

PubMed

Harish, G; Nataraja, M V; Ajay, B C; Holajjer, Prasanna; Savaliya, S D; Gedia, M V

2014-12-01

Groundnut during storage is attacked by number of stored grain pests and management of these insect pests particularly bruchid beetle, Caryedon serratus (Oliver) is of prime importance as they directly damage the pod and kernels. In this regard different storage bags that could be used and duration up to which we can store groundnut has been studied. Super grain bag recorded minimum number of eggs laid and less damage and minimum weight loss in pods and kernels in comparison to other storage bags. Analysis of variance for multiple regression models were found to be significant in all bags for variables viz, number of eggs laid, damage in pods and kernels, weight loss in pods and kernels throughout the season. Multiple comparison results showed that there was a high probability of eggs laid and pod damage in lino bag, fertilizer bag and gunny bag, whereas super grain bag was found to be more effective in managing the C. serratus owing to very low air circulation.

Temporal properties of secondary drop breakup in the bag-stamen breakup regime

NASA Astrophysics Data System (ADS)

Zhao, Hui; Liu, Hai-Feng; Xu, Jian-Liang; Li, Wei-Feng; Lin, Kuang-Fei

2013-05-01

The situation of liquid drop bag-stamen breakup in a continuous air jet flow is investigated by a high speed camera. Test liquids include water, ethanol, and various glycerol mixtures. First, the morphology of bag-stamen breakup is observed and analyzed. The bag-stamen breakup range is found to be in good agreement with the model obtained by Rayleigh-Taylor instability. Then the disk and stamen deformation properties, the fragment average size, and size distribution of ring and stamen are researched in detail, respectively.

Parameter study for child injury mitigation in near-side impacts through FE simulations.

PubMed

Andersson, Marianne; Pipkorn, Bengt; Lövsund, Per

2012-01-01

The objective of this study is to investigate the effects of crash-related car parameters on head and chest injury measures for 3- and 12-year-old children in near-side impacts. The evaluation was made using a model of a complete passenger car that was impacted laterally by a barrier. The car model was validated in 2 crash conditions: the Insurance Institute for Highway Safety (IIHS) and the US New Car Assessment Program (NCAP) side impact tests. The Small Side Impact Dummy (SID-IIs) and the human body model 3 (HBM3) (Total HUman Model for Safety [THUMS] 3-year-old) finite element models were used for the parametric investigation (HBM3 on a booster). The car parameters were as follows: vehicle mass, side impact structure stiffness, a head air bag, a thorax-pelvis air bag, and a seat belt with pretensioner. The studied dependent variables were as follows: resultant head linear acceleration, resultant head rotational acceleration, chest viscous criterion, rib deflection, and relative velocity at head impact. The chest measurements were only considered for the SID-IIs. The head air bag had the greatest effect on the head measurements for both of the occupant models. On average, it reduced the peak head linear acceleration by 54 g for the HBM3 and 78 g for the SID-IIs. The seat belt had the second greatest effect on the head measurements; the peak head linear accelerations were reduced on average by 39 g (HBM3) and 44 g (SID-IIs). The high stiffness side structure increased the SID-IIs' head acceleration, whereas it had marginal effect on the HBM3. The vehicle mass had a marginal effect on SID-IIs' head accelerations, whereas the lower vehicle mass caused 18 g higher head acceleration for HBM3 and the greatest rotational acceleration. The thorax-pelvis air bag, vehicle mass, and seat belt pretensioner affected the chest measurements the most. The presence of a thorax-pelvis air bag, high vehicle mass, and a seat belt pretensioner all reduced the chest viscous criterion (VC) and peak rib deflection in the SID-IIs. The head and thorax-pelvis air bags have the potential to reduce injury measurements for both the SID-IIs and the HBM3, provided that the air bag properties are designed to consider these occupant sizes also. The seat belt pretensioner is also effective, provided that the lateral translation of the torso is managed by other features. The importance of lateral movement management is greater the smaller the occupant is. Light vehicles require interior restraint systems of higher performance than heavy vehicles do to achieve the same level of injury measures for a given side structure. Copyright © 2012 Taylor & Francis Group, LLC

7. DETAIL AT SOUTHEAST 'CORNER' SHOWING CONCRETE FILLED BAGS USED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. DETAIL AT SOUTHEAST 'CORNER' SHOWING CONCRETE FILLED BAGS USED AS EXPLOSION BARRIER TO BLOCKHOUSE TUNNEL ENTRANCE; VIEW TO NORTH. - Cape Canaveral Air Station, Launch Complex 17, Facility 28401, East end of Lighthouse Road, Cape Canaveral, Brevard County, FL

Extending The Shelf Life Of Blood Platelets

NASA Technical Reports Server (NTRS)

Surgenor, Douglas M.

1988-01-01

New method of storing human blood platelets extends vitality for transfusions. Packaged as suspension in sterile liquid in plastic blood bags. Each bag placed between pair of plastic grids, and rubberbands placed around sandwich thus formed to hold together. Stored upright in open air or in container through which air pumped at rate of at least 45 L/min. Ensures that platelets receive ample oxygen and expiratory carbon dioxide form platelets removed before pH drops to harmful levels.

A Reusable, Compliant, Small Volume Blood Reservoir for In Vitro Hemolysis Testing.

PubMed

Olia, Salim E; Herbertson, Luke H; Malinauskas, Richard A; Kameneva, Marina V

2017-02-01

Bench-top in vitro hemolysis testing is a fundamental tool during the design and regulatory safety evaluation of blood-contacting medical devices. While multiple published experimental protocols exist, descriptions of the test loop reservoir remain ambiguous. A critical fixture within the circuit, there is no readily available blood reservoir that ensures thorough mixing and complete air evacuation: two major factors which can affect results. As part of the Food and Drug Administration (FDA) Critical Path Initiative, we developed a three-piece reservoir consisting of a 3D-printed base, a plastic clamp set, and a medical-grade blood bag. This simple, reusable, and cost-effective design was used successfully in the hemolysis assessment of FDA benchmark nozzles and prototype rotary blood pumps, and may be useful as an integral component to any in vitro blood circulation loop. © 2016 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

A Comparison Study of Sampling and Analyzing Volatile Organic Compounds in Air in Kuwait by Using Tedlar Bags/Canisters and GC-MS with a Cryogenic Trap

PubMed Central

Tang, Hongmao; Beg, Khaliq R.; Al-Otaiba, Yousef

2006-01-01

Kuwait experiences desert climatic weather. Due to the extreme hot and dry conditions in this country, some analytical phenomena have been discovered. Therefore, a systematic study of sampling and analyzing volatile organic compounds in air by using GC-MS with a cryogenic trap is reported in this paper. This study included comparisons of using different sample containers such as Tedlar bags and SUMMA canisters, and different cryogenic freezing-out air volumes in the trap. Calibration curves for different compounds and improvement of replicated analysis results were also reported here. The study found that using different sample containers produced different results. Analysis of ambient air samples collected in Tedlar bags obtained several volatile organic compounds with large concentrations compared to using SUMMA canisters. Therefore, to choose a sample container properly is a key element for successfully completing a project. Because GC-MS with a cryogenic trap often generates replicated results with poor agreement, an internal standard added to gas standards and air samples by using a gas syringe was tested. The study results proved that it helped to improve the replicated results. PMID:16699723

A comparison study of sampling and analyzing volatile organic compounds in air in Kuwait by using Tedlar bags/canisters and GC-MS with a cryogenic trap.

PubMed

Tang, Hongmao; Beg, Khaliq R; Al-Otaiba, Yousef

2006-05-12

Kuwait experiences desert climatic weather. Due to the extreme hot and dry conditions in this country, some analytical phenomena have been discovered. Therefore, a systematic study of sampling and analyzing volatile organic compounds in air by using GC-MS with a cryogenic trap is reported in this paper. This study included comparisons of using different sample containers such as Tedlar bags and SUMMA canisters, and different cryogenic freezing-out air volumes in the trap. Calibration curves for different compounds and improvement of replicated analysis results were also reported here. The study found that using different sample containers produced different results. Analysis of ambient air samples collected in Tedlar bags obtained several volatile organic compounds with large concentrations compared to using SUMMA canisters. Therefore, to choose a sample container properly is a key element for successfully completing a project. Because GC-MS with a cryogenic trap often generates replicated results with poor agreement, an internal standard added to gas standards and air samples by using a gas syringe was tested. The study results proved that it helped to improve the replicated results.

40 CFR 63.548 - Monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... bag leak detection and corrective action plans for all baghouses (fabric filters) that are used to... the baghouse through visual inspection of the baghouse interior for air leaks. (8) Quarterly... operation of a bag leak detection system. (d) The procedures specified in the standard operating procedures...

Field Materiel Handling Robot Workcell

DTIC Science & Technology

1986-04-02

20-foot container, one 40-foot container, or two 20-foot containers that can be placed on a single flatbed semitrailer. The Toby- hanna Army Depot...bags are considered to be marginally effective and are easily torn. Laminated rubber air bags are effective with temperature limitations and are

Cervical Spline Analysis for Ejection Injury Prediction.

DTIC Science & Technology

1982-11-30

that the curva- ture ( lordosis ) of the spine will ensure that purely axial load will never exist. A second limitation is that the model is incapable of...tolerate shear; b)- The relative alignment of the spinal lordosis to the acceleration vector. Any ejection configuration which do~es not respect these two... lordosis in or- der to achieve zero shear at the O/CI/C2 joints. An air bag may pre- vent this geometry change. %b suggest that the air bag system should

MARS PATHFINDER AIR BAG INSTALLATION IN SAEF-2

NASA Technical Reports Server (NTRS)

1996-01-01

In the Spacecraft Assembly and Encapsulation Facility-2 (SAEF-2), the Jet Propulsion Laboratory (JPL) team installs air bags on the Mars Pathfinder lander. The four airbags will cushion the lander as it touches down on the Martian surface, protecting the delicate instruments and Surveyor small rover inside the tetrahedral-shaped lander. The Mars Pathfinder is one of two Mars-bound spacecraft being prepared for launch this fall. Liftoff is set for Dec. 2 at the beginning of a 24-day launch period.

Development of a Nutritional Delivery System to Feed Crew in a Pressurized Suit

NASA Technical Reports Server (NTRS)

Glass, J. W.; Leonig, M. L.; Douglas, G. L.

2014-01-01

The contingency scenario for an emergency cabin depressurization event may require crewmembers to subsist in a pressurized suit for up to 144 hours. This scenario requires the capability for safe nutrition delivery through a helmet feed port against a 4 psi pressure differential to enable crewmembers to maintain strength and cognition to perform critical tasks. Two nutritional delivery prototypes were developed and analyzed for compatibility with the helmet feed port interface and for operational effectiveness against the pressure differential. The bag-in-bag (BiB) prototype, designed to equalize the suit pressure with the beverage pouch and enable a crewmember to drink normally, delivered water successfully to three different subjects in suits pressurized to 4 psi. The Boa restrainer pouch, designed to provide mechanical leverage to overcome the pressure differential, did not operate sufficiently. Guidelines were developed and compiled for contingency beverages that provide macro-nutritional requirements, a minimum one-year shelf life, and compatibility with the delivery hardware. Evaluation results and food product parameters have the potential to be used to improve future prototype designs and develop complete nutritional beverages for contingency events. These feeding capabilities would have additional use on extended surface mission EVAs, where the current in-suit drinking device may be insufficient.

Measurements of rates of cooling of a manikin insulated with different mountain rescue casualty bags.

PubMed

Press, Christopher; Duffy, Christopher; Williams, Jonathan; Cooper, Ben; Chapman, Neil

2017-01-01

Accidental hypothermia is common in those who sustain injuries in remote environments. This is unpleasant and associated with adverse effects on subsequent patient outcomes. To minimise further heat loss, a range of insulating systems are available to mountain rescue teams although the most effective and cost-efficient have yet to be determined. Under ambient, still, dry, air conditions, a thermal manikin was filled with water at a temperature of 42 °C and then placed into a given insulation system. Water temperature was then continuously observed via an in-dwelling temperature sensor linked to a PROPAQ 100 series monitor and recorded every 10 min for 130 min. This method was repeated for each insulating package. The vacuum mattress/Pertex©/fibrepile blanket system, either on its own or coupled with the Wiggy bag, was the most efficient with water temperatures only decreasing by 3.2 °C over 130 min. This was followed by the heavy-weight casualty bags without the vacuum mattress/Pertex©/fibrepile blanket system, decreasing by 4.2-4.3 °C. With the Blizzard bag, a decline in water temperature of 5.4 °C was seen over the study duration while a decrease of 9.5 °C was noted when the plastic survival bag was employed. Under the still-air conditions of the study, the vacuum mattress/Pertex©/fibrepile blanket was seen to offer comparable insulation effectiveness compared to be both heavy-weight casualty bags. In turn, these three systems appeared more efficient at insulating the manikin than the Blizzard bag or plastic survival bag.

Magnetic biomonitoring of industrial air pollution in SW Finland

NASA Astrophysics Data System (ADS)

Salo, Hanna; Mäkinen, Joni

2015-04-01

Moss bags made of Sphagnum papillosum were exposed along 8 km transects near Harjavalta Industrial Park in SW Finland. Previous studies have identified Cu-Ni smelter's pipe as the main source of air pollution. Our research hypothesis is that nowadays the local pollution load of airborne particulate matter from Industrial Park is mainly caused by other emission sources than the smelter's pipe. To identify possible magnetic fingerprints, industrial samples (fiberglass filters from the smokestacks of Cu-Ni smelter and Ni-dryer, final Cu-slag, granulated Ni-slag, Cu-concentrates, Ni-concentrates) were investigated. Mass-specific susceptibility and heavy metal levels were significantly higher near Industrial Park and showed a decreasing trend with increasing distance from the source. The magnetic mineralogy of moss bags, smelter's filter and Cu-slag was dominated by a low-coercivity magnetite while high-coercivity minerals were observed in dryer's filter, Ni-slag and majority of concentrates including all Ni-concentrates. Angular and sharp-edged particles prevailed in moss bags and industrial samples, except for smelter's filter and granulated Ni-slag in which spherical particles dominated. Seven air pollution impact zones were distinguished around Industrial Park on the basis of magnetic susceptibility and previous studies. Overall, industrial area's influence is observable up to 4 km and even further distances in SE and NW along prevailing wind directions and Kokemäenjoki River valley. The heaviest anthropogenic air pollution load is deposited at 0.5-1 km distances. Particle morphology and magnetic data of the moss bags indicate that the particulate matter in the hot spot area, which spatial emphasis is in S-SW-W-NW in the upwind from the smelter, originate mainly from the dust emissions from other sources rather than the smelter's pipe. The industrial activities in and nearby hot spot area include handling and moving of concentrates and slags as well as heavy traffic. This study shows that air pollution from various dust-providing sources outweighs the fly-ash load from the Cu-Ni smelter's pipe especially at short distances. Furthermore, active magnetic monitoring by moss bags is spatially detailed sampling method for the identification of air pollutants and emission sources.

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2012 CFR

2012-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2013 CFR

2013-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2014 CFR

2014-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2011 CFR

2011-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2010 CFR

2010-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

GAS CHROMATOGRAPHIC METHOD FOR QUANTITATIVE DETERMINATION OF C2 TO C13 HYDROCARBONS IN ROADWAY VEHICLE EMISSIONS

EPA Science Inventory

A gas chromatographic system was used to quantitate more than 300 gas-phase hydrocarbons from background and roadside ambient air samples. Samples were simultaneously collected in Tedlar bags and on Tenax cartridges. Hydrocarbons from Tedlar bag-collected samples were quantitated...

40 CFR 60.256 - Continuous monitoring requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

....256 Section 60.256 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... rates of 25 Mg (28 tons) per year or more, a bag leak detection system according to the requirements in... performance test on an operating day average basis. (c) Each bag leak detection system used to comply with...

40 CFR 60.256 - Continuous monitoring requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

....256 Section 60.256 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... rates of 25 Mg (28 tons) per year or more, a bag leak detection system according to the requirements in... performance test on an operating day average basis. (c) Each bag leak detection system used to comply with...

40 CFR 60.256 - Continuous monitoring requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

....256 Section 60.256 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... rates of 25 Mg (28 tons) per year or more, a bag leak detection system according to the requirements in... performance test on an operating day average basis. (c) Each bag leak detection system used to comply with...

40 CFR 60.256 - Continuous monitoring requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

....256 Section 60.256 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... rates of 25 Mg (28 tons) per year or more, a bag leak detection system according to the requirements in... performance test on an operating day average basis. (c) Each bag leak detection system used to comply with...

Prototype of the Modular Equipment Transporter (MET)

NASA Technical Reports Server (NTRS)

1970-01-01

A prototype of the Modular Equipment Transporter (MET), nicknamed the 'Rickshaw' after its shape and method of propulsion. This equipment was used by the Apollo 14 astronauts during their geological and lunar surface simulation training in the Pinacate volcanic area of northwestern Sonora, Mexico. The Apollo 14 crew will be the first one to use the MET. It will be a portable workbench with a place for the lunar handtools and their carrier, three cameras, two sample container bags, a Special Environmental Sample Container, spare film magazines, and a Lunar Surface Penetrometer.

Evaluation of passive diffusion bag and dialysis samplers in selected wells at Hickam Air Force Base, Hawaii, July 2001

USGS Publications Warehouse

Vroblesky, Don A.; Pravecek, Tasha

2002-01-01

Field comparisons of chemical concentrations obtained from dialysis samplers, passive diffusion bag samplers, and low-flow samplers showed generally close agreement in most of the 13 wells tested during July 2001 at Hickam Air Force Base, Hawaii. The data for chloride, sulfate, iron, alkalinity, arsenic, and methane appear to show that the dialysis samplers are capable of accurately collecting a passive sample for these constituents. In general, the comparisons of volatile organic compound concentrations showed a relatively close correspondence between the two different types of diffusion samples and between the diffusion samples and the low-flow samples collected in most wells. Divergence appears to have resulted primarily from the pumping method, either producing a mixed sample or water not characteristic of aquifer water moving through the borehole under ambient conditions. The fact that alkalinity was not detected in the passive diffusion bag samplers, highly alkaline waters without volatilization loss from effervescence, which can occur when a sample is acidified for preservation. Both dialysis and passive diffusion bag samplers are relatively inexpensive and can be deployed rapidly and easily. Passive diffusion bag samplers are intended for sampling volatile organic compounds only, but dialysis samplers can be used to sample both volatile organic compounds and inorganic solutes. Regenerated cellulose dialysis samplers, however, are subject to biodegradation and probably should be deployed no sooner than 2 weeks prior to recovery. 1 U.S. Geological Survey, Columbia, South Carolina. 2 Air Florce Center for Environmental Excellence, San Antionio, Texas.

40 CFR 63.1350 - Monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... For a negative-pressure or induced-air fabric filter, the bag leak detector must be installed... Section 63.1350 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission...

An experimental study of permeability within an out-of-autoclave vacuum-bag-only CFRP laminate

NASA Astrophysics Data System (ADS)

Wallace, Landon F.

The out-of-autoclave vacuum-bag-only (OOA-VBO) manufacturing process is a process that eliminates an autoclave when manufacturing aerospace quality carbon fiber reinforced plastics (CFRP). OOA-VBO pre-impregnated resin tow systems rely on air channel networks that guide unwanted voids out of the laminate. The air path networks can be characterized by measuring the permeability of a pre-cured laminate. Permeability results were successfully obtained for a laminate with a compaction similar to that found in a typical vacuum bagging setup. A study was done to find the relationship between compaction of the laminate and permeability. Permeability was measured as the laminate cured, using a constant temperature ramp rate. An experimental nodal analysis was performed to find the permeability at the midpoint of the in-plane direction.

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: PAINT OVERSPRAY ARRESTOR, COLUMBUS INDUSTRIES, INC., SL-90B 8 POCKET BAG

EPA Science Inventory

The report gives results of March 23-24, 1999, tests of Columbus Industries Inc's SL-90B 8 Pocket Bag paint overspray arrestor (POA) as part of an evaluation of POAs by EPA's Air Pollution Control Technology (APCT) Environmental Technology Verification (ETV) Program. The basic pe...

ENVIRONMENTAL TECHNOLOGY VERIFICATION PROGRAM REPORT: PAINT OVERSPRAY ARRESTOR, ATI A-3000 5P BAG

EPA Science Inventory

The report gives results of March 24-25, 1999, tests of ATI's A-3000 5P Bag paint overspray arrestor (POA) as part of an evaluation of POAs by EPA's Air Pollution Control Technology (APCT) Environmental Technology Verification (ETV) Program. The basic performance factor being ver...

40 CFR 63.9804 - What are my monitoring system installation, operation, and maintenance requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... pressure or induced air fabric filters, the bag leak detector must be installed downstream of the fabric... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air...

40 CFR 63.11457 - What are the recordkeeping requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area... calibration and maintenance records. (7) For each bag leak detection system, the records specified in...

40 CFR 63.11457 - What are the recordkeeping requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area... calibration and maintenance records. (7) For each bag leak detection system, the records specified in...

40 CFR 63.11457 - What are the recordkeeping requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area... calibration and maintenance records. (7) For each bag leak detection system, the records specified in...

40 CFR 63.11457 - What are the recordkeeping requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Glass Manufacturing Area... calibration and maintenance records. (7) For each bag leak detection system, the records specified in...

On the Application of a Response Surface Technique to Analyze Roll-over Stability of Capsules with Airbags Using LS-Dyna

NASA Technical Reports Server (NTRS)

Horta, Lucas G.; Reaves, Mercedes C.

2008-01-01

As NASA moves towards developing technologies needed to implement its new Exploration program, studies conducted for Apollo in the 1960's to understand the rollover stability of capsules landing are being revisited. Although rigid body kinematics analyses of the roll-over behavior of capsules on impact provided critical insight to the Apollo problem, extensive ground test programs were also used. For the new Orion spacecraft being developed to implement today's Exploration program, new air-bag designs have improved sufficiently for NASA to consider their use to mitigate landing loads to ensure crew safety and to enable re-usability of the capsule. Simple kinematics models provide only limited understanding of the behavior of these air bag systems, and more sophisticated tools must be used. In particular, NASA and its contractors are using the LS-Dyna nonlinear simulation code for impact response predictions of the full Orion vehicle with air bags by leveraging the extensive air bag prediction work previously done by the automotive industry. However, even in today's computational environment, these analyses are still high-dimensional, time consuming, and computationally intensive. To alleviate the computational burden, this paper presents an approach that uses deterministic sampling techniques and an adaptive response surface method to not only use existing LS-Dyna solutions but also to interpolate from LS-Dyna solutions to predict the stability boundaries for a capsule on airbags. Results for the stability boundary in terms of impact velocities, capsule attitude, impact plane orientation, and impact surface friction are discussed.

40 CFR 63.8600 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... compartment or cell. (7) For negative pressure or induced air fabric filters, the bag leak detector must be... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for...

40 CFR 63.1187 - What do I need to know about operations, maintenance, and monitoring plans?

Code of Federal Regulations, 2011 CFR

2011-07-01

... include: (i) Inspecting the fabric filter for air leaks, torn or broken bags or filter media, or any other... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air...

40 CFR 63.8600 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... compartment or cell. (7) For negative pressure or induced air fabric filters, the bag leak detector must be... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for...

40 CFR 63.1187 - What do I need to know about operations, maintenance, and monitoring plans?

Code of Federal Regulations, 2013 CFR

2013-07-01

... include: (i) Inspecting the fabric filter for air leaks, torn or broken bags or filter media, or any other... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air...

40 CFR 63.8600 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... compartment or cell. (7) For negative pressure or induced air fabric filters, the bag leak detector must be... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for...

40 CFR 63.8600 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... compartment or cell. (7) For negative pressure or induced air fabric filters, the bag leak detector must be... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for...

40 CFR 63.1187 - What do I need to know about operations, maintenance, and monitoring plans?

Code of Federal Regulations, 2012 CFR

2012-07-01

... include: (i) Inspecting the fabric filter for air leaks, torn or broken bags or filter media, or any other... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air...

40 CFR 63.1187 - What do I need to know about operations, maintenance, and monitoring plans?

Code of Federal Regulations, 2014 CFR

2014-07-01

... include: (i) Inspecting the fabric filter for air leaks, torn or broken bags or filter media, or any other... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air...

Influence of surfactant on the drop bag breakup in a continuous air jet stream

NASA Astrophysics Data System (ADS)

Zhao, Hui; Zhang, Wen-Bin; Xu, Jian-Liang; Li, Wei-Feng; Liu, Hai-Feng

2016-05-01

The deformation and breakup of surfactant-laden drops is a common phenomenon in nature and numerous practical applications. We investigate influence of surfactant on the drop bag breakup in a continuous air jet stream. The airflow would induce the advection diffusion of surfactant between interface and bulk of drop. Experiments indicate that the convective motions of deforming drop would induce the non-equilibrium distribution of surfactant, which leads to the change of surface tension. When the surfactant concentration is smaller than critical micelle concentration (CMC), with the increase of surface area of drop, the surface tension of liquid-air interface and the critical Weber number will increase. When the surfactant concentration is bigger than CMC, the micelle can be considered as the source term, which can supply the monomers. So in the presence of surfactant, there would be the significant nonlinear variation on the critical Weber number of bag breakup. We build the dynamic non-monotonic relationship between concentrations of surfactant and critical Weber number theoretically. In the range of parameters studied, the experimental results are consistent with the model estimates.

Prediction of particulate loading in exhaust from fabric filter baghouses with one or more failed bags.

PubMed

Qin, Wenjun; Dekermenjian, Manuel; Martin, Richard J

2006-08-01

Loss of filtration efficiency in a fabric filter baghouse is typically caused by bag failure, in one form or another. The degree of such failure can be as minor as a pinhole leak or as major as a fully involved baghouse fire. In some cases, local air pollution regulations or federal hazardous waste laws may require estimation of the total quantity of particulate matter released to the environment as a result of such failures. In this paper, a technique is presented for computing the dust loading in the baghouse exhaust when one or more bags have failed. The algorithm developed is shown to be an improvement over a previously published result, which requires empirical knowledge of the variation in baghouse pressure differential with bag failures. An example calculation is presented for a baghouse equipped with 200 bags. The prediction shows that a small percentage of failed bags can cause a relatively large proportion of the gas flow to bypass the active bags, which, in turn, leads to high outlet dust loading and low overall collection efficiency from the baghouse.

40 CFR 61.147 - Standard for fabricating.

Code of Federal Regulations, 2011 CFR

2011-07-01

... dust deposits on the clean side of bags. For air cleaning devices that cannot be inspected on a weekly... Section 61.147 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Asbestos...

40 CFR 61.147 - Standard for fabricating.

Code of Federal Regulations, 2014 CFR

2014-07-01

... dust deposits on the clean side of bags. For air cleaning devices that cannot be inspected on a weekly... Section 61.147 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Asbestos...

Comparison of glass vessels and plastic bags for enclosing living plant parts for headspace analysis.

PubMed

Stewart-Jones, Alex; Poppy, Guy M

2006-04-01

Plants release volatile chemicals into their surrounding air space that can affect the physiology of neighboring plants and influence the behavior of insects. In studying these interactions, it is desirable to collect volatiles from plants that have not been excised and are growing under as natural conditions as possible. We compared a vessel of borosilicate glass and Nylon-6 or polyester [poly(ethyleneterephthalate) or PET] cooking bags for enclosing plants during collection of volatiles. A push-pull airflow system was used, and volatiles were trapped on Tenax TA and analyzed by gas chromatography after thermal desorption. Low levels of impurities were found for the glass vessel and polyester bags. Nylon bags contained higher levels and more impurities. Recoveries of standards of 10 plant volatiles were measured in static and dynamic systems. In a static air system, there was good recovery only from the glass vessel. In a dynamic system, there was generally good recovery from both the glass vessel and polyester bags. Recoveries of alpha-pinene and (Z)-jasmone were poor throughout. The former was shown to have a very low breakthrough volume on the Tenax TA adsorbent, and the latter may be strongly adsorbed on glass. All three materials were essentially transparent in the IR and visible (photosynthetic) range but with significantly different absorptions in the UV range. In a simulated dynamic entrainment in full sunlight, internal vessel temperatures were higher than ambient by up to 9.5 degrees C in the glass vessel and 7.5 degrees C in the polyester bag. Lower increases in temperature relative to ambient (<1 degrees C) were recorded when entrainments were conducted in the shade. In a field trial, the profiles of volatiles collected from an apple tree infested with rosy apple aphid using a glass vessel and a polyester bag were similar. Polyester bags are recommended as more convenient than glass vessels for the enclosure of plants during the collection of volatiles.

Double Vacuum Bag Process for Resin Matrix Composite Manufacturing

NASA Technical Reports Server (NTRS)

Hou, Tan-Hung (Inventor); Jensen, Brian J. (Inventor)

2007-01-01

A double vacuum bag molding assembly with improved void management and laminate net shape control which provides a double vacuum enviromnent for use in fabricating composites from prepregs containing air and/or volatiles such as reactive resin matrix composites or composites from solvent containing prepregs with non-reactive resins matrices. By using two vacuum environments during the curing process, a vacuum can be drawn during a B-stage of a two-step cycle without placing the composite under significant relative pressure. During the final cure stage, a significant pressure can be applied by releasing the vacuum in one of the two environments. Inner and outer bags are useful for creating the two vacuum environments with a perforated tool intermediate the two. The composite is placed intermediate a tool plate and a caul plate in the first environment with the inner bag and tool plate defining the first environment. The second environment is characterized by the outer bag which is placed over the inner bag and the tool plate.

Preliminary Process Design of ITER ELM Coil Bracket Brazing

NASA Astrophysics Data System (ADS)

LI, Xiangbin; SHI, Yi

2015-03-01

With the technical requirement of the International Thermonuclear Experimental Reactor (ITER) project, the manufacture and assembly technology of the mid Edge Localized Modes (ELM) coil was developed by the Institute of Plasma Physics, Chinese Academy of Science (ASIPP). As the gap between the bracket and the Stainless Steel jacketed and Mineral Insulated Conductor (SSMIC) can be larger than 0.5 mm instead of 0.01 mm to 0.1 mm as in normal industrial cases, the process of mid ELM coil bracket brazing to the SSMICT becomes quiet challenging, from a technical viewpoint. This paper described the preliminary design of ELM coil bracket brazing to the SSMIC process, the optimal bracket brazing curve and the thermal simulation of the bracket furnace brazing method developed by ANSYS. BAg-6 foil (Bag50Cu34Zn16) plus BAg-1a paste (Bag45CuZnCd) solders were chosen as the brazing filler. By testing an SSMICT prototype, it is shown that the average gap between the bracket and the SSMIC could be controlled to 0.2-0.3 mm, and that there were few voids in the brazing surface. The results also verified that the preliminary design had a favorable heat conducting performance in the bracket.

Critically safe vacuum pickup for use in wet or dry cleanup of radioactive materials

DOEpatents

Zeren, Joseph D.

1994-01-01

A vacuum pickup of critically safe quantity and geometric shape is used in cleanup of radioactive materials. Collected radioactive material is accumulated in four vertical, parallel, equally spaced canisters arranged in a cylinder configuration. Each canister contains a filter bag. An upper intake manifold includes four 90 degree spaced, downward facing nipples. Each nipple communicates with the top of a canister. The bottom of each canister communicates with an exhaust manifold comprising four radially extending tubes that meet at the bottom of a centrally located vertical cylinder. The top of the central cylinder terminates at a motor/fan power head. A removable HEPA filter is located intermediate the top of the central cylinder and the power head. Four horizontal bypass tubes connect the top of the central cylinder to the top of each of the canisters. Air enters the vacuum cleaner via a hose connected to the intake manifold. Air then travels down the canisters, where particulate material is accumulated in generally equal quantities in each filter bag. Four air paths of bag filtered air then pass radially inward to the bottom of the central cylinder. Air moves up the central cylinder, through the HEPA filter, through a vacuum fan compartment, and exits the vacuum cleaner. A float air flow valve is mounted at the top of the central cylinder. When liquid accumulates to a given level within the central cylinder, the four bypass tubes, and the four canisters, suction is terminated by operation of the float valve.

Residential heating contribution to level of air pollutants (PAHs, major, trace, and rare earth elements): a moss bag case study.

PubMed

Vuković, Gordana; Aničić Urošević, Mira; Pergal, Miodrag; Janković, Milan; Goryainova, Zoya; Tomašević, Milica; Popović, Aleksandar

2015-12-01

In areas with moderate to continental climates, emissions from residential heating system lead to the winter air pollution peaks. The EU legislation requires only the monitoring of airborne concentrations of particulate matter, As, Cd, Hg, Ni, and B[a]P. Transition metals and rare earth elements (REEs) have also arisen questions about their detrimental health effects. In that sense, this study examined the level of extensive set of air pollutants: 16 polycyclic aromatic hydrocarbons (PAHs), and 41 major elements, trace elements, and REEs using Sphagnum girgensohnii moss bag technique. During the winter of 2013/2014, the moss bags were exposed across Belgrade (Serbia) to study the influence of residential heating system to the overall air quality. The study was set as an extension to our previous survey during the summer, i.e., non-heating season. Markedly higher concentrations of all PAHs, Sb, Cu, V, Ni, and Zn were observed in the exposed moss in comparison to the initial values. The patterns of the moss REE concentrations normalized to North American Shale Composite and Post-Archean Australian Shales were identical across the study area but enhanced by anthropogenic activities. The results clearly demonstrate the seasonal variations in the moss enrichment of the air pollutants. Moreover, the results point out a need for monitoring of air quality during the whole year, and also of various pollutants, not only those regulated by the EU Directive.

40 CFR 63.7830 - What are my monitoring requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... equivalent means. (vi) Make monthly visual checks of bag tension on reverse air and shaker-type baghouses to....7830 Section 63.7830 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED...

40 CFR 63.11552 - What are my monitoring requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... filter for air leaks, torn or broken bags or filter media, or any other condition that may cause an...? 63.11552 Section 63.11552 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.11552 - What are my monitoring requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... filter for air leaks, torn or broken bags or filter media, or any other condition that may cause an...? 63.11552 Section 63.11552 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.7830 - What are my monitoring requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... equivalent means. (vi) Make monthly visual checks of bag tension on reverse air and shaker-type baghouses to...? 63.7830 Section 63.7830 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.7830 - What are my monitoring requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... equivalent means. (vi) Make monthly visual checks of bag tension on reverse air and shaker-type baghouses to...? 63.7830 Section 63.7830 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.11552 - What are my monitoring requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... filter for air leaks, torn or broken bags or filter media, or any other condition that may cause an...? 63.11552 Section 63.11552 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.11552 - What are my monitoring requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... filter for air leaks, torn or broken bags or filter media, or any other condition that may cause an...? 63.11552 Section 63.11552 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.8665 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... defined in the Clean Air Act, in § 63.2, and in this section as follows: Air pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Bag leak...? 63.8665 Section 63.8665 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.8665 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... defined in the Clean Air Act, in § 63.2, and in this section as follows: Air pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Bag leak...? 63.8665 Section 63.8665 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.8665 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... defined in the Clean Air Act, in § 63.2, and in this section as follows: Air pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Bag leak...? 63.8665 Section 63.8665 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.8665 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... defined in the Clean Air Act, in § 63.2, and in this section as follows: Air pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Bag leak...? 63.8665 Section 63.8665 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

Review of Various Air Sampling Methods for Solvent Vapors.

ERIC Educational Resources Information Center

Maykoski, R. T.

Vapors of trichloroethylene, toluene, methyl ethyl ketone, and butyl cellosolve in air were collected using Scotchpac and Tedlar bags, glass prescription bottles, and charcoal adsorption tubes. Efficiencies of collection are reported. (Author/RH)

40 CFR 63.7331 - What are the installation, operation, and maintenance requirements for my monitors?

Code of Federal Regulations, 2010 CFR

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air... baghouse applied to pushing emissions, you must install, operate, and maintain each bag leak detection...

40 CFR 63.8450 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for... bag leak detection system, you must meet the requirements in paragraphs (e)(1) through (11) of this...

40 CFR 60.57c - Monitoring requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... pressure or induced air fabric filters, the bag leak detector shall be installed downstream of the fabric... 60.57c Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... owner or operator of an affected facility using an air pollution control device other than a dry...

40 CFR 63.8450 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for... bag leak detection system, you must meet the requirements in paragraphs (e)(1) through (11) of this...

40 CFR 60.57c - Monitoring requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pressure or induced air fabric filters, the bag leak detector shall be installed downstream of the fabric... 60.57c Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... owner or operator of an affected facility using an air pollution control device other than a dry...

40 CFR 63.11527 - What are the monitoring requirements for new and existing sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for... an existing affected source, you may install, operate, and maintain a bag leak detection system for...

40 CFR 63.8450 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for... bag leak detection system, you must meet the requirements in paragraphs (e)(1) through (11) of this...

40 CFR 63.8450 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for... bag leak detection system, you must meet the requirements in paragraphs (e)(1) through (11) of this...

40 CFR 63.11527 - What are the monitoring requirements for new and existing sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for... an existing affected source, you may install, operate, and maintain a bag leak detection system for...

40 CFR 63.9600 - What are my operation and maintenance requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) through (vi) of this section. (i) Inspecting the baghouse for air leaks, torn or broken bags or filter... requirements? 63.9600 Section 63.9600 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.9600 - What are my operation and maintenance requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) through (vi) of this section. (i) Inspecting the baghouse for air leaks, torn or broken bags or filter... requirements? 63.9600 Section 63.9600 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.11527 - What are the monitoring requirements for new and existing sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for... an existing affected source, you may install, operate, and maintain a bag leak detection system for...

Date of Pollen Shedding by Longleaf Pine Advanced by Increased Temperatures at Strobili

Treesearch

W.D. Boyer; F.W. Woods

1973-01-01

Air temperatures in the microenvironments of flower buds of Pinus palustris Mill. appear to be a major determinant of flowering date. Shoots bearing staminate strobili on each of 10 trees were bagged at different times and for varying lengths of time in January and February. Bagging treatments provided 488 to 3,852 additional degree-hr of heat...

40 CFR 86.159-08 - Exhaust emission test procedures for US06 emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... gasoline-fueled Otto-cycle vehicles, the composite samples collected in bags are analyzed for THC, CO, CO2, CH4, and NOX. For petroleum-fueled diesel-cycle vehicles, THC is sampled and analyzed continuously according to the provisions of § 86.110. Parallel bag samples of dilution air are analyzed for THC, CO, CO2...

40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... collected in bags are analyzed for THC, CO, CO2, CH4, and NOX. For petroleum-fueled diesel-cycle vehicles, THC is sampled and analyzed continuously according to the provisions of § 86.110. Parallel bag samples of dilution air are analyzed for THC, CO, CO2, CH4, and NOX. (b) Dynamometer activities. (1) All...

40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... collected in bags are analyzed for THC, CO, CO2, CH4, and NOX. For petroleum-fueled diesel-cycle vehicles, THC is sampled and analyzed continuously according to the provisions of § 86.110. Parallel bag samples of dilution air are analyzed for THC, CO, CO2, CH4, and NOX. (b) Dynamometer activities. (1) All...

40 CFR 86.159-08 - Exhaust emission test procedures for US06 emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... gasoline-fueled Otto-cycle vehicles, the composite samples collected in bags are analyzed for THC, CO, CO2, CH4, and NOX. For petroleum-fueled diesel-cycle vehicles, THC is sampled and analyzed continuously according to the provisions of § 86.110. Parallel bag samples of dilution air are analyzed for THC, CO, CO2...

40 CFR 86.159-08 - Exhaust emission test procedures for US06 emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... gasoline-fueled Otto-cycle vehicles, the composite samples collected in bags are analyzed for THC, CO, CO2, CH4, and NOX. For petroleum-fueled diesel-cycle vehicles, THC is sampled and analyzed continuously according to the provisions of § 86.110. Parallel bag samples of dilution air are analyzed for THC, CO, CO2...

40 CFR 86.159-08 - Exhaust emission test procedures for US06 emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... gasoline-fueled Otto-cycle vehicles, the composite samples collected in bags are analyzed for THC, CO, CO2, CH4, and NOX. For petroleum-fueled diesel-cycle vehicles, THC is sampled and analyzed continuously according to the provisions of § 86.110. Parallel bag samples of dilution air are analyzed for THC, CO, CO2...

40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... collected in bags are analyzed for THC, CO, CO2, CH4, and NOX. For petroleum-fueled diesel-cycle vehicles, THC is sampled and analyzed continuously according to the provisions of § 86.110. Parallel bag samples of dilution air are analyzed for THC, CO, CO2, CH4, and NOX. (b) Dynamometer activities. (1) All...

40 CFR 86.159-08 - Exhaust emission test procedures for US06 emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... gasoline-fueled Otto-cycle vehicles, the composite samples collected in bags are analyzed for THC, CO, CO2, CH4, and NOX. For petroleum-fueled diesel-cycle vehicles, THC is sampled and analyzed continuously according to the provisions of § 86.110. Parallel bag samples of dilution air are analyzed for THC, CO, CO2...

14 CFR 399.85 - Notice of baggage fees and other fees.

Code of Federal Regulations, 2014 CFR

2014-01-01

....85 Notice of baggage fees and other fees. (a) If a U. S. or foreign air carrier has a website... disclose any increase in its fee for carry-on or first and second checked bags and any change in the first and second checked bags or carry-on allowance for a passenger on the homepage of that website (e.g...

14 CFR 399.85 - Notice of baggage fees and other fees.

Code of Federal Regulations, 2012 CFR

2012-01-01

....85 Notice of baggage fees and other fees. (a) If a U. S. or foreign air carrier has a website... disclose any increase in its fee for carry-on or first and second checked bags and any change in the first and second checked bags or carry-on allowance for a passenger on the homepage of that website (e.g...

14 CFR 399.85 - Notice of baggage fees and other fees.

Code of Federal Regulations, 2013 CFR

2013-01-01

....85 Notice of baggage fees and other fees. (a) If a U. S. or foreign air carrier has a website... disclose any increase in its fee for carry-on or first and second checked bags and any change in the first and second checked bags or carry-on allowance for a passenger on the homepage of that website (e.g...

Peepoo bag: self-sanitising single use biodegradable toilet.

PubMed

Vinnerås, Björn; Hedenkvist, Mikael; Nordin, Annika; Wilhelmson, Anders

2009-01-01

Unsafe water, sanitation and hygiene together with deficient nutritional status are major contributors to the global burden of disease. Safe collection, disposal and reuse of human excreta would enable the risk of transmission of diseases to be decreased and household food security to be increased in many regions. However, the majority of the 2.5 billion people lacking improved sanitation comprise poor people in societies with weak infrastructure. This study developed a low cost sanitation option requiring little investment and maintenance--a single use, self-sanitising, biodegradable toilet (Peepoo bag) and tested it for smell, degradability and hygiene aspects. It was found that no smell was detectable from a 25 microm thick bag filled with faeces during 24 h in a 10 m2 room at 30 degrees C. Bags that had been in contact with urea-treated faeces or urine for 2 months in air, compost or water at 24 or 37 degrees C showed little signs of degradation. Furthermore, pathogen inactivation modelling of the 4 g of urea present in the bag indicated that appropriate sanitation of faecal material collected is achieved in the bag within 2-4 weeks, after which the bag can be degraded and reused as fertiliser.

Prediction of particulate loading in exhaust from fabric filter baghouses with one or more failed bags

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wenjun Qin; Manuel Dekermenjian; Richard J. Martin

2006-08-15

Loss of filtration efficiency in a fabric filter baghouse is typically caused by bag failure, in one form or another. The degree of such failure can be as minor as a pinhole leak or as major as a fully involved baghouse fire. In some cases, local air pollution regulations or federal hazardous waste laws may require estimation of the total quantity of particulate matter released to the environment as a result of such failures. In this paper, a technique is presented for computing the dust loading in the baghouse exhaust when one or more bags have failed. The algorithm developedmore » is shown to be an improvement over a previously published result, which requires empirical knowledge of the variation in baghouse pressure differential with bag failures. An example calculation is presented for a baghouse equipped with 200 bags. The prediction shows that a small percentage of failed bags can cause a relatively large proportion of the gas flow to bypass the active bags, which, in turn, leads to high outlet dust loading and low overall collection efficiency from the baghouse. 10 refs., 5 figs., 3 tabs.« less

Air: Simple Experiments for Young Scientists.

ERIC Educational Resources Information Center

White, Larry

This book contains simple experiments through which students explore air and its properties. Some of the topics discussed include alternative energy, bacteria, carbon dioxide, motion, weather, and flight. Experiments include: blowing a balloon up in a bottle; seeing air in water; making a lunch-bag kite, weather vanes, and paper glider;…

40 CFR 86.521-90 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... apparatus. The methanol is vaporized and swept into the sample bag with a known volume of zero grade air....521-90 Section 86.521-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... and basic operating adjustment using the appropriate FID fuel and zero-grade air. (2) Optimize on the...

40 CFR 86.1221-90 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... apparatus. The methanol is vaporized and swept into the sample bag with a known volume of zero grade air....1221-90 Section 86.1221-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... appropriate FID fuel and zero-grade air. (2) Optimize on the most common operating range. Introduce into the...

40 CFR 86.521-90 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... apparatus. The methanol is vaporized and swept into the sample bag with a known volume of zero grade air....521-90 Section 86.521-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... and basic operating adjustment using the appropriate FID fuel and zero-grade air. (2) Optimize on the...

40 CFR 86.121-90 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... sample bag with a known volume of zero grade air measured by a gas flow meter meeting the performance....121-90 Section 86.121-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... operating adjustment using the appropriate FID fuel and zero-grade air. (2) Optimize on the most common...

40 CFR 86.121-90 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... sample bag with a known volume of zero grade air measured by a gas flow meter meeting the performance....121-90 Section 86.121-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... operating adjustment using the appropriate FID fuel and zero-grade air. (2) Optimize on the most common...

40 CFR 86.1221-90 - Hydrocarbon analyzer calibration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... apparatus. The methanol is vaporized and swept into the sample bag with a known volume of zero grade air....1221-90 Section 86.1221-90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... appropriate FID fuel and zero-grade air. (2) Optimize on the most common operating range. Introduce into the...

40 CFR 63.11163 - What are the standards and compliance requirements for new sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Primary... to a control device. (d) You must install, operate, and maintain a bag leak detection system on all...

40 CFR 62.14454 - How must I monitor the required parameters?

Code of Federal Regulations, 2014 CFR

2014-07-01

... installed in each baghouse compartment or cell. (7) For negative pressure or induced air FF, the bag leak...) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS FOR DESIGNATED FACILITIES AND... use an air pollution control device that includes a FF and are not demonstrating compliance using PM...

40 CFR 62.14454 - How must I monitor the required parameters?

Code of Federal Regulations, 2013 CFR

2013-07-01

... installed in each baghouse compartment or cell. (7) For negative pressure or induced air FF, the bag leak...) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS FOR DESIGNATED FACILITIES AND... use an air pollution control device that includes a FF and are not demonstrating compliance using PM...

Strategy for selecting disposable bags for cell culture media applications based on a root-cause investigation.

PubMed

Wood, Joseph; Mahajan, Ekta; Shiratori, Masaru

2013-01-01

The use of disposable bags for cell culture media storage has grown significantly in the past decade. Some of the key advantages of using disposable bags relative to non-disposable containers include increased product throughput, decreased cleaning validation costs, reduced risk of cross contamination and lower facility costs. As the scope of use of disposable bags for cell culture applications increases, problematic bags and scenarios should be identified and addressed to continue improving disposables technologies and meet the biotech industry's needs. In this article, we examine a cell culture application wherein media stored in disposable bags is warmed at 37°C before use for cell culture operations. A problematic bag film was identified through a prospective and retrospective cell culture investigation. The investigation provided information on the scope and variation of the issue with respect to different Chinese hamster ovary (CHO) cell lines, cell culture media, and application-specific parameters. It also led to the development of application-specific test methods and enabled a strategy for disposable bag film testing. The strategy was implemented for qualifying an alternative bag film for use in our processes. In this test strategy, multiple lots of 13 bag film types, encompassing eight vendors were evaluated using a three round, cell culture-based test strategy. The test strategy resulted in the determination of four viable bag film options based on the technical data. The results of this evaluation were used to conclude that a volatile or air-quenched compound, likely generated by gamma irradiation of the problematic bag film, negatively impacted cell culture performance. © 2013 American Institute of Chemical Engineers.

A Single Chip Automotive Control LSI Using SOI Bipolar Complimentary MOS Double-Diffused MOS

NASA Astrophysics Data System (ADS)

Kawamoto, Kazunori; Mizuno, Shoji; Abe, Hirofumi; Higuchi, Yasushi; Ishihara, Hideaki; Fukumoto, Harutsugu; Watanabe, Takamoto; Fujino, Seiji; Shirakawa, Isao

2001-04-01

Using the example of an air bag controller, a single chip solution for automotive sub-control systems is investigated, by using a technological combination of improved circuits, bipolar complimentary metal oxide silicon double-diffused metal oxide silicon (BiCDMOS) and thick silicon on insulator (SOI). For circuits, an automotive specific reduced instruction set computer (RISC) center processing unit (CPU), and a novel, all integrated system clock generator, dividing digital phase-locked loop (DDPLL) are proposed. For the device technologies, the authors use SOI-BiCDMOS with trench dielectric-isolation (TD) which enables integration of various devices in an integrated circuit (IC) while avoiding parasitic miss operations by ideal isolation. The structures of the SOI layer and TD, are optimized for obtaining desired device characteristics and high electromagnetic interference (EMI) immunity. While performing all the air bag system functions over a wide range of supply voltage, and ambient temperature, the resulting single chip reduces the electronic parts to about a half of those in the conventional air bags. The combination of single chip oriented circuits and thick SOI-BiCDMOS technologies offered in this work is valuable for size reduction and improved reliability of automotive electronic control units (ECUs).

[Contamination levels to room air arising from the use of 99mTc-gas and prevention from the contamination].

PubMed

Komatani, A; Akutsu, T; Yamaguchi, K; Onodera, Y; Manaka, Y; Takahashi, K

1996-04-01

99mTc-gas (TECHNEGAS) is a 99mTc-labeled micro-aerosol which is considered to have different behavior from 133Xe or 81mKr gas. In order to estimate contamination levels to room air arising from the use of 99mTc-gas, filtered expired air during administration and 1, 2, 3, 5, 10 min after the administration were collected in each polyethylene bag. Radioactivities of the polyethylene bags, used filter and the lung were measured with 3-head scintillation camera. The activity of the expired air diminished within 6-10 min and about 5% of whole discharged 99mTc-gas was released to room air. The activity of the used filter was two times of the lung. According to these results, it is recommended that the 99mTc-gas may be administrated in a exclusive room. The administrated patient and used filter must be remain in the exclusive room.

Dietary Assessment on a Mobile Phone Using Image Processing and Pattern Recognition Techniques: Algorithm Design and System Prototyping.

PubMed

Probst, Yasmine; Nguyen, Duc Thanh; Tran, Minh Khoi; Li, Wanqing

2015-07-27

Dietary assessment, while traditionally based on pen-and-paper, is rapidly moving towards automatic approaches. This study describes an Australian automatic food record method and its prototype for dietary assessment via the use of a mobile phone and techniques of image processing and pattern recognition. Common visual features including scale invariant feature transformation (SIFT), local binary patterns (LBP), and colour are used for describing food images. The popular bag-of-words (BoW) model is employed for recognizing the images taken by a mobile phone for dietary assessment. Technical details are provided together with discussions on the issues and future work.

Heavy - metal biomonitoring by using moss bags in Florence urban area, Italy

NASA Astrophysics Data System (ADS)

Pellizzaro, Grazia; Canu, Annalisa; Arca, Angelo; Duce, Pierpaolo

2013-04-01

In the last century, pollution has become one of the most important risks for environment. In particular, heavy metal presence in air, water and soil induces toxic effects on ecosystems and human health. Monitoring airborne trace element over large areas is a task not easy to reach since the concentrations of pollutants are variable in space and time. Data from automatic devices are site-specific and very limited in number to describe spatial-temporal trends of pollutants. In addition, especially in Italy, trace elements concentrations are not often recorded by most of the automated monitoring stations. In the last decades, development of alternative and complementary methods as bio-monitoring techniques, allowed to map deposition patterns not only near single pollution sources, but also over relatively large areas at municipal or even regional scale. Bio-monitoring includes a wide array of methodologies finalised to study relationships between pollution and living organisms. Mosses and lichens have been widely used as bio-accumulators for assessing the atmospheric deposition of heavy metals in natural ecosystems and urban areas. In this study bio-monitoring of airborne trace metals was made using moss bags technique. The moss Hypnum cupressiforme was used as bio-indicator for estimating atmospheric traces metal deposition in the urban area of Florence. Moss carpets were collected in a forested area of central Sardinia (municipality of Bolotana - Nuoro), which is characterised by absence of air pollution. Moss bags were located in the urban area of Florence close to three monitoring air quality stations managed by ARPAT (Agenzia Regionale Protezione Ambiente Toscana). Two stations were located in high-traffic roads whereas the other one was located in a road with less traffic density. In each site moss bags were exposed during three campaigns of measurement conducted during the periods March-April, May-July, and August-October 2010. Two moss bags, used as control, were not exposed. After exposure periods, moss bags were removed and moss samples were analyzed for As, Cr, Cu, Fe, Ni, Pb, V, and Zn by Inductively Coupled Plasma Atomic Emission Spectrometry. Results show differences between mean concentration of trace metals in moss bags after-exposure and the respective blanks in the three sample sites of Florence during the three campaigns of measurement. The highest concentrations for almost all elements were recorded at high-traffic road sites. Whereas lower values were detected in site located in a road with less traffic density In conclusion, Hypnum cupressiforme, for his high ability to accumulate trace metals, can be efficiently used as bio-indicator to estimate the trend of air pollution in a urban area during a period time.

DOE Office of Scientific and Technical Information (OSTI.GOV)

May, C.A.; Breitigam, W.; Bauer, R.S.

The laminates that are used to prepare advanced composite parts generally require curing at high temperature and pressure, and their raw material shelf lives are limited. The epoxy resin systems that the authors describe here offer the potential of extended shelf life while curing at relatively low temperatures with a method the authors call rapid thermoset processing (RTP). A laminate is formed by stacking the prepreg in a pre-determined manner as required by the end product configuration. The prepreg is then bagged by placing it in a sealed envelope of a heat-resistant film, which is subsequently bonded to a metalmore » surface (the tool) with a heat-resistant vacuum bag putty. The bag has an access hole through which vacuum can be applied to the prepreg stack, facilitating removal of air and other volatiles. This assembly is then heated under vacuum and pressure in an autoclave, the resin melts, and any excess air or volatile matter bleeds from the configuration, resulting in the required dense, void-free laminate.« less

Long-term (1992-2004) record of lead, cadmium, and zinc air contamination in Warsaw, Poland: determination by chemical analysis of moss bags and leaves of Crimean linden.

PubMed

Dmuchowski, Wojciech; Bytnerowicz, Andrzej

2009-12-01

Between 1992 and 2004, air contamination with lead (Pb), cadmium (Cd), and zinc (Zn) in Warsaw, Poland, was monitored annually with moss (Sphagnum fallax) bags on a network of 230 sites covering the entire city. During the study the highest contamination was near the Warszawa Steel Mill, northwestern Warsaw. Lead concentrations in moss bags decreased in time, while those of Cd and Zn did not show clear trends. Between 1994 and 2004, Pb, Cd, and Zn were also monitored in the Crimean linden (Tilia Euchlora) foliage along the main city avenue and in a northwestern warsaw park. Lead concentrations decreased more near the avenue than in the park, indicating that the phasing-out of leaded gasoline had a major effect on reduced Pb contamination in Warsaw. At the same time, foliar concentrations of Cd and Zn in both areas decreased much less.

40 CFR 63.1206 - When and how must you comply with the standards and operating requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants from Hazardous... time under § 63.6(i) or § 63.1213, except: (1) Cement kilns are exempt from the bag leak detection...

40 CFR 63.1206 - When and how must you comply with the standards and operating requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants from Hazardous... time under § 63.6(i) or § 63.1213, except: (1) Cement kilns are exempt from the bag leak detection...

Heavy metals dispersion during thermal treatment of plastic bags and its recovery.

PubMed

Alam, Ohidul; Wang, Sijia; Lu, Wentao

2018-04-15

One of the main worries for thermal treatment of plastic bag (PB) is the air pollution resulting from heavy metal (HM) evaporation and emission. The quest of the study was to investigate their fate during thermal treatment varying with temperature and atmosphere to explore the appropriate treatment technology. Four commonly consumed polymer bags such as PE, HDPE, LDPE and PVC were selected for the analysis. The elemental compositions, heating values and total metal contents of the samples were measured by an elemental analyzer, a sulphur/halogen analyzer, a bomb calorimeter and an ICP-OES, respectively. Thermal treatments of the samples were conducted in a tube furnace at 350, 550, 650, 750, and 850 °C with 1 L/min air or N 2 gas flow, respectively. 5% HNO 3 /10% H 2 O 2 solution was used for absorbing metals from gas phase, and then HM distributions both in flue gas and bottom ash were determined. Results revealed that the lower heating values of HDPE, LDPE, PVC and PE bags were 33.32, 34.28, 24.82 and 36.7 MJ/kg, respectively indicating energy recovery potential. Thermal treatment showed the maximum mass reduction (>90%) of PB at 850 °C. The higher percentage of metals was distributed in ash at initial temperature that promoted to gas with rise of temperature. The used absorption solution exhibited tremendous quantity of metals recovery. However, there was no significant difference between using air and N 2 gas flow during treatment of PB. Copyright © 2018 Elsevier Ltd. All rights reserved.

Open-circuit respirometry: a brief historical review of the use of Douglas bags and chemical analyzers.

PubMed

Shephard, Roy J

2017-03-01

The Douglas bag technique is reviewed as one in a series of articles looking at historical insights into measurement of whole body metabolic rate. Consideration of all articles looking at Douglas bag technique and chemical gas analysis has here focused on the growing appreciation of errors in measuring expired volumes and gas composition, and subjective reactions to airflow resistance and dead space. Multiple small sources of error have been identified and appropriate remedies proposed over a century of use of the methodology. Changes in the bag lining have limited gas diffusion, laboratories conducting gas analyses have undergone validation, and WHO guidelines on airflow resistance have minimized reactive effects. One remaining difficulty is a contamination of expirate by dead space air, minimized by keeping the dead space <70 mL. Care must also be taken to ensure a steady state, and formal validation of the Douglas bag method still needs to be carried out. We may conclude that the Douglas bag method has helped to define key concepts in exercise physiology. Although now superceded in many applications, the errors in a meticulously completed measurement are sufficiently low to warrant retention of the Douglas bag as the gold standard when evaluating newer open-circuit methodology.

An Ethical Basis for Autonomous System Deployment

DTIC Science & Technology

2009-09-24

Discussion on Robo -Ethics, Amsterdam, NL, March 2008.GSU Neurophilosophy 20. Brown Bag Lunch Series, "Governing Lethal Behavior: Embedding Ethics in an...5. Implementation of responsibility advisor : An ethical permission responsibility advisor was prototyped and demonstrated in a manner fully...PTF_Interface_Final_Largev3.mpg • Demonstration of the Ethical Responsibility Advisor : http://www.cc.gatech.edu/ai/robot-lab/ethics/res-advisor.mpg

40 CFR 49.10711 - Federal Implementation Plan for the Astaris-Idaho LLC Facility (formerly owned by FMC Corporation...

Code of Federal Regulations, 2011 CFR

2011-07-01

... of the Fort Hall Indian Reservation. Bag leak detection guidance means Office of Air Quality Planning... FEDERAL ASSISTANCE INDIAN COUNTRY: AIR QUALITY PLANNING AND MANAGEMENT Implementation Plans for Tribes... the meaning accorded them under the Clean Air Act, except as follows: Astaris-Idaho or Astaris-Idaho...

View of Expedition 15 FE Anderson performing the ANITA Experiment in the Node 1

NASA Image and Video Library

2007-10-06

ISS015-E-32200 (6 Oct. 2007) --- Astronaut Clay Anderson, Expedition 15 flight engineer, uses an air sample pump and 2.5 liter gas sample bag to gather and analyze air samples for the Analyzing Interferometer for Ambient Air (ANITA) experiment in the Unity node of the International Space Station.

Air elimination capability in rapid infusion systems.

PubMed

Zoremba, N; Gruenewald, C; Zoremba, M; Rossaint, R; Schaelte, G

2011-11-01

Pressure infusion devices are used in clinical practice to apply large volumes of fluid over a short period of time. Although air infusion is a major complication, they have limited capability to detect and remove air during pressure infusion. In this investigation, we tested the air elimination capabilities of the Fluido(®) (The Surgical Company), Level 1(®) (Level 1 Technologies Inc.) and Ranger(®) (Augustine Medical GmbH) pressure infusion devices. Measurements were undertaken with a crystalloid solution during an infusion flow of 100, 200, 400 and 800 ml.min(-1). Four different volumes of air (25, 50, 100 and 200 ml) were injected as boluses in one experimental setting, or infused continuously over the time needed to perfuse 2 l saline in the other setting. The perfusion fluid was collected in an airtight infusion bag and the amount of air obtained in the bag was measured. The delivered air volume was negligible and would not cause any significant air embolism in all experiments. In our experimental setting, we found, during high flow, an increased amount of uneliminated air in all used devices compared with lower perfusion flows. All tested devices had a good air elimination capability. The use of ultrasonic air detection coupled with an automatic shutoff is a significant safety improvement and can reliably prevent accidental air embolism at rapid flows. © 2011 The Authors. Anaesthesia © 2011 The Association of Anaesthetists of Great Britain and Ireland.

Environmental contamination, product contamination and workers exposure using a robotic system for antineoplastic drug preparation.

PubMed

Sessink, Paul J M; Leclercq, Gisèle M; Wouters, Dominique-Marie; Halbardier, Loïc; Hammad, Chaïma; Kassoul, Nassima

2015-04-01

Environmental contamination, product contamination and technicians exposure were measured following preparation of iv bags with cyclophosphamide using the robotic system CytoCare. Wipe samples were taken inside CytoCare, in the clean room environment, from vials, and prepared iv bags including ports and analysed for contamination with cyclophosphamide. Contamination with cyclophosphamide was also measured in environmental air and on the technicians hands and gloves used for handling the drugs. Exposure of the technicians to cyclophosphamide was measured by analysis of cyclophosphamide in urine. Contamination with cyclophosphamide was mainly observed inside CytoCare, before preparation, after preparation and after daily routine cleaning. Contamination outside CytoCare was incidentally found. All vials with reconstituted cyclophosphamide entering CytoCare were contaminated on the outside but vials with powdered cyclophosphamide were not contaminated on the outside. Contaminated bags entering CytoCare were also contaminated after preparation but non-contaminated bags were not contaminated after preparation. Cyclophosphamide was detected on the ports of all prepared bags. Almost all outer pairs of gloves used for preparation and daily routine cleaning were contaminated with cyclophosphamide. Cyclophosphamide was not found on the inner pairs of gloves and on the hands of the technicians. Cyclophosphamide was not detected in the stationary and personal air samples and in the urine samples of the technicians. CytoCare enables the preparation of cyclophosphamide with low levels of environmental contamination and product contamination and no measurable exposure of the technicians. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Crash scene photography in motor vehicle crashes without air bag deployment.

PubMed

Newgard, Craig D; Martens, Katherine A; Lyons, Evelyn M

2002-09-01

To determine whether vehicle characteristics, measured using crash scene photography, are associated with anatomic patterns of injury and severity of injury sustained in motor vehicle crashes (MVCs) without air bag deployment. A prospective observational study was conducted over 22 months, using 12 fire departments serving two hospitals. Two vehicle photographs (exterior and interior) were taken at each MVC. Vehicular variables were assigned by grading the photographs with a standardized scoring system, and outcome information on each patient was collected by chart review. Five hundred fifty-nine patients were entered into the study. Frontal crashes and increasing passenger space intrusion (PSI) were associated with head, facial, and lower-extremity injuries, while rear crashes were associated with spinal injuries. Restraint use had a protective effect in head, facial, and upper and lower extremity injuries, yet was associated with higher odds of spinal injury. Lack of restraint use, increasing PSI, and steering wheel deformity were associated with an increased hospital length of stay and hospital charges, yet only steering wheel deformity was associated with increasing injury severity when adjusting for other crash variables. Out-of-hospital variables, as obtained from crash vehicle photography, are associated with injury site, injury severity, hospital length of stay, and hospital charges in patients involved in MVCs without air bag deployment.

Particulate Air Pollution Control for Army Coal-Fired Boiler Plants.

DTIC Science & Technology

1983-03-01

Army flue gas . The condensed material usually is sticky and emissions control . Of the current new technologies. traps the flyash on the bag, where it... control device is made a matter of convenience. The location Flue gas temperature control is an important factor of other components is given the prime...consideration. *in the application of baghouses to flue gas particulate This often results in the particle-laden gas being forced control . Bag

Best options for the exposure of traditional and innovative moss bags: A systematic evaluation in three European countries.

PubMed

Capozzi, F; Giordano, S; Aboal, J R; Adamo, P; Bargagli, R; Boquete, T; Di Palma, A; Real, C; Reski, R; Spagnuolo, V; Steinbauer, K; Tretiach, M; Varela, Z; Zechmeister, H; Fernández, J A

2016-07-01

To develop an internationally standardized protocol for the moss bag technique application, the research team participating in the FP7 European project "MOSSclone" focused on the optimization of the moss bags exposure in terms of bag characteristics (shape of the bags, mesh size, weight/surface ratio), duration and height of exposure by comparing traditional moss bags to a new concept bag, "Mossphere". In particular, the effects of each variable on the metal uptake from the air were evaluated by a systematic experimental design carried out in urban, industrial, agricultural and background areas of three European countries with oceanic, Mediterranean and continental climate. The results evidenced that the shape, the mesh size of the bags and the exposure height (in the tested ranges), did not significantly influence the uptake capacity of the transplanted moss. The aspects more affecting the element uptake were represented by the density of the moss inside the bags and the relative ratio between its weight and the surface area of the bag. We found that, the lower the density, the higher the uptake recorded. Moreover, three weeks of exposure were not enough to have a consistent uptake signal in all the environments tested, thus we suggest an exposure period not shorter than 6 weeks, which is appropriate in most situations. The above results were confirmed in all the countries and scenarios tested. The adoption of a shared exposure protocol by the research community is strongly recommended since it is a key aspect to make biomonitoring surveys directly comparable, also in view of its recognition as a monitoring method by the EU legislation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of temperature and relative humidity during transportation on green coffee bean moisture content and ochratoxin A production.

PubMed

Palacios-Cabrera, Hector A; Menezes, Hilary C; Iamanaka, Beatriz T; Canepa, Frederico; Teixeira, Aldir A; Carvalhaes, Nelson; Santi, Domenico; Leme, Plinio T Z; Yotsuyanagi, Katumi; Taniwaki, Marta H

2007-01-01

Changes in temperature, relative humidity, and moisture content of green coffee beans were monitored during transportation of coffee from Brazil to Italy. Six containers (three conventional and three prototype) were stowed in three different places (hold, first floor, and deck) on the ship. Each prototype was located next to a conventional container. The moisture content of the coffee in the container located on the first floor was less affected by environmental variations (0.7%) than that in the hold and on the deck. Coffee located in the hold showed the highest variation in moisture content (3%); in addition, the container showed visible condensation. Coffee transported on the deck showed an intermediary variation in moisture (2%), and there was no visible condensation. The variation in coffee moisture content of the prototype containers was similar to that of the conventional ones, especially in the top layers of coffee bags (2 to 3%), while the increase in water activity was 0.70. This suggests that diffusion of moisture occurs very slowly inside the cargo and that there are thus sufficient time and conditions for fungal growth. The regions of the container near the wall and ceiling are susceptible to condensation since they are close to the headspace with its high relative humidity. Ochratoxin A production occurred in coffee located at the top of the container on the deck and in the wet bags from the hold (those found to be wet on opening the containers at the final destination).

Dietary Assessment on a Mobile Phone Using Image Processing and Pattern Recognition Techniques: Algorithm Design and System Prototyping

PubMed Central

Probst, Yasmine; Nguyen, Duc Thanh; Tran, Minh Khoi; Li, Wanqing

2015-01-01

Dietary assessment, while traditionally based on pen-and-paper, is rapidly moving towards automatic approaches. This study describes an Australian automatic food record method and its prototype for dietary assessment via the use of a mobile phone and techniques of image processing and pattern recognition. Common visual features including scale invariant feature transformation (SIFT), local binary patterns (LBP), and colour are used for describing food images. The popular bag-of-words (BoW) model is employed for recognizing the images taken by a mobile phone for dietary assessment. Technical details are provided together with discussions on the issues and future work. PMID:26225994

Optimizing the passenger air bag of an adaptive restraint system for multiple size occupants.

PubMed

Bai, Zhonghao; Jiang, Binhui; Zhu, Feng; Cao, Libo

2014-01-01

The development of the adaptive occupant restraint system (AORS) has led to an innovative way to optimize such systems for multiple size occupants. An AORS consists of multiple units such as adaptive air bags, seat belts, etc. During a collision, as a supplemental protective device, air bags can provide constraint force and play a role in dissipating the crash energy of the occupants' head and thorax. This article presents an investigation into an adaptive passenger air bag (PAB). The purpose of this study is to develop a base shape of a PAB for different size occupants using an optimization method. Four typical base shapes of a PAB were designed based on geometric data on the passenger side. Then 4 PAB finite element (FE) models and a validated sled with different size dummy models were developed in MADYMO (TNO, Rijswijk, The Netherlands) to conduct the optimization to obtain the best baseline PAB that would be used in the AORS. The objective functions-that is, the minimum total probability of injuries (∑Pcomb) of the 5th percentile female and 50th and 95th percentile male dummies-were adopted to evaluate the optimal configurations. The injury probability (Pcomb) for each dummy was adopted from the U.S. New Car Assessment Program (US-NCAP). The parameters of the AORS were first optimized for different types of PAB base shapes in a frontal impact. Then, contact time duration and force between the PAB and dummy head/chest were optimized by adjusting the parameters of the PAB, such as the number and position of tethers, lower the Pcomb of the 95th percentile male dummy. According to the optimization results, 4 typical PABs could provide effective protection to 5th and 50th percentile dummies. However, due to the heavy and large torsos of the 95th percentile occupants, the current occupant restraint system does not demonstrate satisfactory protective function, particularly for the thorax.

40 CFR 63.9631 - What are my monitoring requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... maintain a bag leak detection system to monitor the relative change in particulate matter loadings... of ensuring the proper functioning of removal mechanisms. (3) Check the compressed air supply of... interior for air leaks. (8) Inspect fans for wear, material buildup, and corrosion through quarterly visual...

Integrated Seawater Sampler and Data Acquisition System Prototype

DTIC Science & Technology

1993-04-01

circuitry. The sample bags, initially sealed in a chemically clean environment , were opened by pumping the water out of the tray, thus forcing water into...the water sample containers from materials having low metals content. Control of the sample transfer environment through the use of Class-100 clean... environment . CTD designers also intended their underwater units and deck terminals to be connected directly together providing AC grounding appropriate to

40 CFR 60.105a - Monitoring of emissions and operations for fluid catalytic cracking units (FCCU) and fluid coking...

Code of Federal Regulations, 2012 CFR

2012-07-01

... for air leaks, torn or broken bags or filter media, or any other condition that may cause an increase... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF... nozzles must conduct a daily check of the air or water pressure to the spray nozzles and record the...

Why wrapping premature neonates to prevent hypothermia can predispose to overheating.

PubMed

Agourram, Bouchra; Bach, Véronique; Tourneux, Pierre; Krim, Gérard; Delanaud, Stéphane; Libert, Jean-Pierre

2010-06-01

Wrapping low-birth-weight neonates in a plastic bag prevents body heat loss. A bonnet can also be used, since large amounts of heat can be lost from the head region, but may provide too much thermal insulation, thus increasing the risk of overheating. We assessed the time required to reach warning body temperature (t38 degrees C), heat stroke (t40 degrees C), or extreme value (t43 degrees C) in a mathematical model that involved calculating various local body heat losses. Simulated heat exchanges were based on body surface temperature distribution measured in preterm neonates exposed to 33 degrees C air temperature (relative air humidity: 35%; air velocity: <0.1 m/s) and covered (torso and limbs) or not with a transparent plastic bag. We also compared metabolic heat production with body heat losses when a bonnet (2 or 3.5 mm thick) covered 10%, 40%, or 100% of the head. Wrapping neonates in a bag (combined or not with a bonnet) does not induce a critical situation as long as metabolic heat production does not increase. When endogenous heat production rises, t38 degrees C ranged between 75 and 287, t40 degrees C between 185 and 549, and t43 degrees C between 287 and 702 min. When this increase was accompanied by a fall in skin temperature, overheating risk was accentuated (37

Prototype Systems for Measuring Outdoor Air Intake Rates in Rooftop Air Handlers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fisk, William J.; Chan, Wanyu R.; Hotchi, Toshifumi

2015-01-01

The widespread absence of systems for real-time measurement and feedback control, of minimum outdoor air intake rates in HVAC systems contributes to the poor control of ventilation rates in commercial buildings. Ventilation rates affect building energy consumption and influence occupant health. The project designed fabricated and tested four prototypes of systems for measuring rates of outdoor air intake into roof top air handlers. All prototypes met the ±20% accuracy target at low wind speeds, with all prototypes accurate within approximately ±10% after application of calibration equations. One prototype met the accuracy target without a calibration. With two of four prototypemore » measurement systems, there was no evidence that wind speed or direction affected accuracy; however, winds speeds were generally below usually 3.5 m s -1 (12.6 km h -1) and further testing is desirable. The airflow resistance of the prototypes was generally less than 35 Pa at maximum RTU air flow rates. A pressure drop of this magnitude will increase fan energy consumption by approximately 4%. The project did not have resources necessary to estimate costs of mass produced systems. The retail cost of components and materials used to construct prototypes ranged from approximately $1,200 to $1,700. The test data indicate that the basic designs developed in this project, particularly the designs of two of the prototypes, have considerable merit. Further design refinement, testing, and cost analysis would be necessary to fully assess commercial potential. The designs and test results will be communicated to the HVAC manufacturing community.« less

40 CFR 63.7740 - What are my monitoring requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... a bag leak detection system according to the requirements in § 63.7741(b). (c) For each baghouse... the proper functioning of removal mechanisms. (3) Check the compressed air supply for pulse-jet... integrity of the baghouse through quarterly visual inspections of the baghouse interior for air leaks. (8...

Air Travel Health Tips

MedlinePlus

... health Before your flight One key to air travel is to prepare ahead of time. If you are carrying on a bag, make ... need to change if your eating and sleeping times will change at your destination. If you have diabetes or epilepsy, you should travel with your ID card. For instance, the American ...

40 CFR 1060.525 - How do I test fuel systems for diurnal emissions?

Code of Federal Regulations, 2010 CFR

2010-07-01

... fuel tanks, and volume-compensating air bags. (b) You may subtract your fuel tank's permeation...) AIR POLLUTION CONTROLS CONTROL OF EVAPORATIVE EMISSIONS FROM NEW AND IN-USE NONROAD AND STATIONARY... diurnal emission standard. (8) For emission control technologies that rely on a sealed fuel system, you...

40 CFR 1060.525 - How do I test fuel systems for diurnal emissions?

Code of Federal Regulations, 2011 CFR

2011-07-01

... fuel tanks, and volume-compensating air bags. (b) You may subtract your fuel tank's permeation...) AIR POLLUTION CONTROLS CONTROL OF EVAPORATIVE EMISSIONS FROM NEW AND IN-USE NONROAD AND STATIONARY... diurnal emission standard. (8) For emission control technologies that rely on a sealed fuel system, you...

49 CFR 585.11 - Scope.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Requirements § 585.11 Scope. This subpart establishes requirements for manufacturers of passenger cars and... air bag requirements of Standard No. 208, Occupant crash protection (49 CFR 571.208). ...

49 CFR 585.11 - Scope.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Requirements § 585.11 Scope. This subpart establishes requirements for manufacturers of passenger cars and... air bag requirements of Standard No. 208, Occupant crash protection (49 CFR 571.208). ...

49 CFR 585.11 - Scope.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Requirements § 585.11 Scope. This subpart establishes requirements for manufacturers of passenger cars and... air bag requirements of Standard No. 208, Occupant crash protection (49 CFR 571.208). ...

49 CFR 585.11 - Scope.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Requirements § 585.11 Scope. This subpart establishes requirements for manufacturers of passenger cars and... air bag requirements of Standard No. 208, Occupant crash protection (49 CFR 571.208). ...

49 CFR 585.11 - Scope.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Requirements § 585.11 Scope. This subpart establishes requirements for manufacturers of passenger cars and... air bag requirements of Standard No. 208, Occupant crash protection (49 CFR 571.208). ...

49 CFR 579.22 - Reporting requirements for manufacturers of 100 or more buses, manufacturers of 500 or more...

Code of Federal Regulations, 2012 CFR

2012-10-01

..., 14 air bags, 15 seat belts, 16 structure, 17 latch, 18 vehicle speed control, 19 tires, 20 wheels, 21...., hydraulic or air), the information required by this subsection shall be reported by each of the two brake types. If the service brake system in a vehicle is not readily characterized as either hydraulic or air...

49 CFR 579.22 - Reporting requirements for manufacturers of 100 or more buses, manufacturers of 500 or more...

Code of Federal Regulations, 2011 CFR

2011-10-01

..., 14 air bags, 15 seat belts, 16 structure, 17 latch, 18 vehicle speed control, 19 tires, 20 wheels, 21...., hydraulic or air), the information required by this subsection shall be reported by each of the two brake types. If the service brake system in a vehicle is not readily characterized as either hydraulic or air...

Safety and durability of low-density polyethylene bags in solar water disinfection applications.

PubMed

Danwittayakul, Supamas; Songngam, Supachai; Fhulua, Tipawan; Muangkasem, Panida; Sukkasi, Sittha

2017-08-01

Solar water disinfection (SODIS) is a simple point-of-use process that uses sunlight to disinfect water for drinking. Polyethylene terephthalate (PET) bottles are typically used as water containers for SODIS, but a new SODIS container design has recently been developed with low-density polyethylene (LDPE) bags and can overcome the drawbacks of PET bottles. Two nesting layers of LDPE bags are used in the new design: the inner layer containing the water to be disinfected and the outer one creating air insulation to minimize heat loss from the water to the surroundings. This work investigated the degradation of LDPE bags used in the new design in actual SODIS conditions over a period of 12 weeks. The degradation of the LDPE bags was investigated weekly using a scanning electron microscope, Fourier transform infrared spectroscopy, ultraviolet-visible spectrophotometer, and tensile strength tester. It was found that the LDPE bags gradually degraded under the sunlight due to photo-oxidation reactions, especially in the outer bags, which were directly exposed to the sun and surroundings, leading to the reduction of light transmittance (by 11% at 300 nm) and tensile strength (by 33%). In addition, possible leaching of organic compounds into the water contained in the inner bags was examined using gas chromatography-mass spectrometer. 2,4-Di-tert-butylphenol was found in some SODIS water samples as well as the as-received water samples, in the concentration range of 1-4 μg/L, which passes the Environmental Protection Agency Drinking Water Guidance on Disinfection By-Products.

A study on feasibility of super adobe technology –an energy efficient building system using natural resources in Bangladesh

NASA Astrophysics Data System (ADS)

Kamal, Razia; Saifur Rahman, Md.

2018-04-01

The inspiration and concept for the Superadobe system originates not from the modern architecture design experience, but from the influence of traditional rural buildings and landscape, together with a 13th century Persian poet named Jala Ad-Din Muhammad Balkhi, Rumi. The poetry sprit of Rumi, connects and enlightens the architectural theme of Nader Khalili with natural resources that anybody in the world should be able to build a home for his or her family with the simplest of elements: Earth, Water, Air and Fire. Therefore, to build a human shelter that will give maximum safety with low financial budget and minimum environmental impact with natural disaster resilient a Superadobe Technology has been adopted. The Superadobe, a form of earth bag construction using sandbag and barbed wire technology, is an economical, time efficient, energy efficient and ecologically friendly system developed by Iranian-born architect “Nader Khalili”. The system connects the natural materials and rural traditions to create a new way to use natural materials such as mud, water, air and fire which can be finished in a short time without any large construction equipment. The goal of this study is to introduce the building system, analyse the ventilation, lighting and insulation of the prototype of Superadobe system replacing the contextual earth house in Bangladesh.

Preparation for Bagging OA-7 CYGNUS

NASA Image and Video Library

2017-02-21

In the Space Station Processing Facility high bay at NASA's Kennedy Space Center in Florida, technicians are preparing Orbital ATK's CYGNUS pressurized cargo module for bagging. The Orbital ATK CRS-7 commercial resupply services mission to the International Space Station is scheduled to launch atop a United Launch Alliance Atlas V rocket from Space Launch Complex 41 at Cape Canaveral Air Force Station on March 19, 2017. CYGNUS will deliver thousands of pounds of supplies, equipment and scientific research materials to the space station.

Autonomous Integrated Receive System (AIRS) requirements definition. Volume 4: Functional specification for the prototype Automated Integrated Receive System (AIRS)

NASA Technical Reports Server (NTRS)

Chie, C. M.

1984-01-01

The functional requirements for the performance, design, and testing for the prototype Automated Integrated Receive System (AIRS) to be demonstrated for the TDRSS S-Band Single Access Return Link are presented.

Advanced Avalanche Safety Equipment of Backcountry Users: Current Trends and Perceptions.

PubMed

Ng, Pearlly; Smith, William R; Wheeler, Albert; McIntosh, Scott E

2015-09-01

Backcountry travelers should carry a standard set of safety gear (transceiver, shovel, and probe) to improve rescue chances and reduce mortality risk. Many backcountry enthusiasts are using other advanced equipment such as an artificial air pocket (eg, the AvaLung) or an avalanche air bag. Our goal was to determine the numbers of backcountry users carrying advanced equipment and their perceptions of mortality and morbidity benefit while carrying this gear. A convenience sample of backcountry skiers, snowboarders, snowshoers, and snowmobilers was surveyed between February and April 2014. Participants of this study were backcountry mountain users recruited at trailheads in the Wasatch and Teton mountain ranges of Utah and Wyoming, respectively. Questions included prior avalanche education, equipment carried, and perceived safety benefit derived from advanced equipment. In all, 193 surveys were collected. Skiers and snowboarders were likely to have taken an avalanche safety course, whereas snowshoers and snowmobilers were less likely to have taken a course. Most backcountry users (149, 77.2%), predominantly skiers and snowboarders, carried standard safety equipment. The AvaLung was carried more often (47 users) than an avalanche air bag (10 users). The avalanche air bag had a more favorable perceived safety benefit. A majority of participants reported cost as the barrier to obtaining advanced equipment. Standard avalanche safety practices, including taking an avalanche safety course and carrying standard equipment, remain the most common safety practices among backcountry users in the Wasatch and Tetons. Snowshoers remain an ideal target for outreach to increase avalanche awareness and safety. Copyright © 2015 Wilderness Medical Society. Published by Elsevier Inc. All rights reserved.

75 FR 24945 - Agency Information Collection Activities; Submission to OMB for Review and Approval; Comment...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-06

... Emission Standards for Hazardous Air Pollutants (NESHAP) for Mineral Wool Production (40 CFR part 63... wool production plants are required to install fabric filter bag leak detection systems and then... Air Act. The required information consists of emissions data and other information that have been...

40 CFR 60.56c - Compliance and performance testing.

Code of Federal Regulations, 2011 CFR

2011-07-01

....56c Section 60.56c Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... (defined oxygen correction basis); 20.9=oxygen concentration in air, percent; and %O2=oxygen concentration... compliance with the PM standards using bag leak detection systems as specified in § 60.57c(h) or PM CEMS as...

77 FR 2536 - Agency Information Collection Activities; Submission to OMB for Review and Approval; Comment...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-18

... parameters; (2) bag leak detention systems; (3) maintenance plan for air pollution control devices (e.g.... Abstract: The National Emission Standards for Hazardous Air Pollutants (NESHAP) using Maximum Achievable Control Technology were proposed on August 4, 1998, promulgated on May 20, 1999, and amended most recently...

40 CFR 60.56c - Compliance and performance testing.

Code of Federal Regulations, 2010 CFR

2010-07-01

....56c Section 60.56c Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... (defined oxygen correction basis); 20.9=oxygen concentration in air, percent; and %O2=oxygen concentration... compliance with the PM standards using bag leak detection systems as specified in § 60.57c(h) or PM CEMS as...

75 FR 11873 - Agency Information Collection Activities; Submission to OMB for Review and Approval; Comment...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-12

... Emission Standards for Hazardous Air Pollutants (NESHAP) for Iron and Steel Foundries (40 CFR part 63... foundries that are major sources of hazardous air pollutant (HAP) emissions. The rule applies to emissions... lead compounds, and identify the date, time, cause, and corrective actions taken for all bag-leak...

A novel tamponade agent for management of post partum hemorrhage: adaptation of the Xstat mini-sponge applicator for obstetric use.

PubMed

Rodriguez, Maria I; Jensen, Jeffrey T; Gregory, Kenton; Bullard, Mary; Longo, Paul; Heidel, Jerry; Edelman, Alison

2017-06-13

Although uterine tamponade is an effective treatment for postpartum hemorrhage (PPH), current methods have key limitations in their use, particularly in low resource settings. The XStat™ Mini Sponge Dressing (MSD) is approved for the management of non-compressible wounds in the battlefield/trauma setting. The MSD applies highly compressed medical sponges capable of stopping high-flow arterial bleeding within seconds. The objective of our study was to adopt the MSD for use in managing PPH. We performed desktop testing using a uterine model with pressure sensors to compare key design elements of the obstetrical prototype MSD (fundal pressure achieved, reduction in fluid loss, time to deploy, and time to remove) with alternativetechniques (uterine packing, balloon tamponade). To evaluate safety, we delivered the fetus of pregnant ewes by cesarean section and used the prototype to deliver the MSD into one uterine horn, and closed the hysterotomy. We followed the clinical recovery of animals (n = 3) over 24 h, and then removed the reproductive tract for histologic evaluation. To evaluate late effects, we surgically removed the MSDs after 24 h, and followed the clinical recovery of animals (n = 6) for an additional seven days before tissue removal. The obstetrical prototype has a long tapered delivery system designed to be deployed during vaginal examination, and administers three times the volume of the approved MSD trauma bandage. The MSD are deployed within a mesh bag to facilitate removal by vaginaltraction. On desktop testing, the MSD resulted in the highest average fundal pressure (113 mmHg), followed by the MSD bag device (85.8 mmHg), gauze packing (15.5 mmHg), and the uterine balloon (8.2 mmHg). The MSD bag test group achieved the largest fluid flow reduction of -74%, followed by gauze packing (-55%), MSD (-35%), and uterine balloon (-19%). Animal testing demonstrated good uterine fill with no evidence of adverse clinical recovery, uterine trauma or infection at 24 h, or up to 7 days following device removal. We adapted a highly effective trauma dressing and applicator for use in the treatment of severe PPH. Preliminary desktop and animal testing provide a basis for initial clinical trials in women.

Towards the methodological optimization of the moss bag technique in terms of contaminants concentrations and replicability values

NASA Astrophysics Data System (ADS)

Ares, A.; Fernández, J. A.; Carballeira, A.; Aboal, J. R.

2014-09-01

The moss bag technique is a simple and economical environmental monitoring tool used to monitor air quality. However, routine use of the method is not possible because the protocols involved have not yet been standardized. Some of the most variable methodological aspects include (i) selection of moss species, (ii) ratio of moss weight to surface area of the bag, (iii) duration of exposure, and (iv) height of exposure. In the present study, the best option for each of these aspects was selected on the basis of the mean concentrations and data replicability of Cd, Cu, Hg, Pb and Zn measured during at least two exposure periods in environments affected by different degrees of contamination. The optimal choices for the studied aspects were the following: (i) Sphagnum denticulatum, (ii) 5.68 mg of moss tissue for each cm-2 of bag surface, (iii) 8 weeks of exposure, and (iv) 4 m height of exposure. Duration of exposure and height of exposure accounted for most of the variability in the data. The aim of this methodological study was to provide data to help establish a standardized protocol that will enable use of the moss bag technique by public authorities.

Air Bag Installation

NASA Technical Reports Server (NTRS)

2003-01-01

May 10, 2003Prelaunch at Kennedy Space Center

On Mars Exploration Rover 1 (MER-1) , air bags are installed on the lander. The airbags will inflate to cushion the landing of the spacecraft on the surface of Mars. When it stops bouncing and rolling, the airbags will deflate and retract, the petals will open to bring the lander to an upright position, and the rover will be exposed. NASA's twin Mars Exploration Rovers are designed to study the history of water on Mars. These robotic geologists are equipped with a robotic arm, a drilling tool, three spectrometers, and four pairs of cameras that allow them to have a human-like, 3D view of the terrain. Each rover could travel as far as 100 meters in one day to act as Mars scientists' eyes and hands, exploring an environment where humans can't yet go. MER-1 is scheduled to launch June 25 as MER-B aboard a Delta II rocket from Cape Canaveral Air Force Station.

Droplet-air collision dynamics: Evolution of the film thickness

NASA Astrophysics Data System (ADS)

Opfer, L.; Roisman, I. V.; Venzmer, J.; Klostermann, M.; Tropea, C.

2014-01-01

This study is devoted to the experimental and theoretical investigation of aerodynamic drop breakup phenomena. We show that the phenomena of drop impact onto a rigid wall, drop binary collisions, and aerodynamic drop deformation are similar if the correct scaling is applied. Then we use observations of the deforming drop to estimate the evolution of the film thickness of the bag, the value that determines the size of the fine child drops produced by bag breakup. This prediction of film thickness, based on film kinematics, is validated for the initial stage by direct drop thickness measurements and at the latest stage by the data obtained from the velocity of hole expansion in the film. It is shown that the film thickness correlates well with the dimensionless position of the bag apex.

Magnetic biomonitoring by moss bags for industry-derived air pollution in SW Finland

NASA Astrophysics Data System (ADS)

Salo, Hanna; Mäkinen, Joni

2014-11-01

We provide the first detailed case study using Sphagnum papillosum moss bags for active magnetic monitoring of airborne industrial pollution in order to evaluate the actual role of various emission sources and the competence of current environmental protection actions relative to the air quality. The origin and spatial spreading of particulate matter (PM) based on magnetic, chemical, and SEM-EDX analyses was studied around the Industrial Park in Harjavalta, SW Finland. The data was collected during two 6-month sampling periods along 8 km transects in 2010-2011. The results support our hypothesis that the main emission source of PM is not the Cu-Ni smelter's pipe as presumed in previous chemical monitorings. We argue that the hot spot area within the severe impact pollution zone is related to slag processing and/or other unidentified industrial activity. At short distances various dust-providing sources outweigh the fly-ash load from the Cu-Ni smelter's pipe. Active magnetic monitoring by moss bags will help in planning environmental actions as well as in improvement of health conditions for industrial staff and town residents living next to the Industrial Park.

The effect of dentine pre-treatment using bioglass and/or polyacrylic acid on the interfacial characteristics of resin-modified glass ionomer cements.

PubMed

Sauro, Salvatore; Watson, Timothy; Moscardó, Agustin Pascual; Luzi, Arlinda; Feitosa, Victor Pinheiro; Banerjee, Avijit

2018-06-01

To evaluate the effect of load-cycle aging and/or 6 months artificial saliva (AS) storage on bond durability and interfacial ultramorphology of resin-modified glass ionomer cement (RMGIC) applied onto dentine air-abraded using Bioglass 45S5 (BAG) with/without polyacrylic acid (PAA) conditioning. RMGIC (Ionolux, VOCO) was applied onto human dentine specimens prepared with silicon-carbide abrasive paper or air-abraded with BAG with or without the use of PAA conditioning. Half of bonded-teeth were submitted to load cycling (150,000 cycles) and half immersed in deionised water for 24 h. They were cut into matchsticks and submitted immediately to microtensile bond strength (μTBS) testing or 6 months in AS immersion and subsequently μTBS tested. Results were analysed statistically by two-way ANOVA and Student-Newman-Keuls test (α = 0.05). Fractographic analysis was performed using FE-SEM, while further RMGIC-bonded specimens were surveyed for interfacial ultramorphology characterisation (dye-assisted nanoleakage) using confocal microscopy. RMGIC applied onto dentine air-abraded with BAG regardless PAA showed no significant μTBS reduction after 6 months of AS storage and/or load cycling (p > 0.05). RMGIC-dentine interface showed no sign of degradation/nanoleakage after both aging regimens. Conversely, interfaces created in PAA-conditioned SiC-abraded specimens showed significant reduction in μTBS (p < 0.05) after 6 months of storage and/or load cycling with evident porosities within bonding interface. Dentine pre-treatment using BAG air-abrasion might be a suitable strategy to enhance the bonding performance and durability of RMGIC applied to dentine. The use of PAA conditioner in smear layer-covered dentine may increase the risk of degradation at the bonding interface. A combined dentine pre-treatment using bioglass followed by PAA may increase the bond strength and maintain it stable over time. Conversely, the use of PAA conditioning alone may offer no significant contribute to the immediate and prolonged bonding performance. Copyright © 2018 Elsevier Ltd. All rights reserved.

The impact of safety belt use on liver injuries in motor vehicle crashes: the importance of motor vehicle safety systems.

PubMed

Holbrook, Troy Lisa; Hoyt, David B; Eastman, A Brent; Sise, Michael J; Kennedy, Frank; Velky, Tom; Conroy, Carol; Pacyna, Sharon; Erwin, Steve

2007-08-01

Liver injuries (LIs) are one of the most serious and common consequences of motor vehicle crashes (MVCs). In the unstable patient, early detection of LI based on clinical suspicion will improve acute trauma care and outcomes. The specific objectives of this analysis are to identify crash scene and occupant risk factors for LI from MVC. Crash Injury Research and Engineering Network data were used to identify risk factors for LI; age, sex, safety belt use, air bag deployment, DeltaV (change in velocity), principal direction of force, vehicle crush, and intrusion. Occupants with LI were compared with four control groups without LI; (1) no abdominal (ABD) injury (NO_ABD), (2) any ABD (ANY_ABD), (3) ABD Abbreviated Injury Scale score of 1 to 2 (ABD_1-2), and (4) ABD Abbreviated Injury Scale score of 3 or more (ABD_3+). LI occupants were compared with each control group and odds ratios (OR) for risk of LI were computed. There were 311 Crash Injury Research and Engineering Network subjects aged 5 or more years with LI. The total mean Injury Severity Score was 37.6. LI was strongly and significantly associated with safety belt restraint use without air bag deployment, compared with each control group: Liver injury - restrained + air bag not deployed versus (1) NO_ABD, N = 1,519; OR = 4.4, (2) ANY_ABD, N = 317; OR = 2.6, (3) ABD_1 to 2, N = 155; OR = 3.1, (4) ABD_3+, N = 217; OR = 2.4 (p < 0.001). This association was independent of driver or passenger status and principal direction of force. LIs were also strongly and significantly associated with greater vehicle interior intrusion. LIs were strongly associated with a safety belt restraint in use in the absence of air bag deployment during MVC. This data may have profound importance to the trauma surgeon as an early indicator for LI during resuscitation. These findings also have important implications for future research efforts to improve safety systems in motor vehicles and reduce morbidity and mortality from MVCs in the United States.

Cool Space Bags Filled With Funny Voice Air Studying Space Rain

NASA Astrophysics Data System (ADS)

Halford, A. J.; MacDonald, E.

2016-12-01

Today I will tell you a bit about our work: big bags of funny voice air looking at space rain into the top of the sky, where there's not much sky left. So what makes stuff, both hot and cold tiny stuff, and I mean tiny tiny things, like really tiny things, fall into the top of the sky? Many different things. Some of these things are really really long waves, long waves, short waves that make angry cat noises, and short waves that sound like animals that fly in the morning along with other things. But how do we study this? We use big bags filled with funny voice air to fly near the top of the sky. When the tiny things that can't be seen rain into the top of the sky they make lights that can not be seen by eye, some move fast like the tiny things and many move slower. Our big bags of funny voice air carry computers and things that can see this light that can not be seen by eye. We use this not seen light to tell us what stuff fell into the top of the sky. Some waves will push the slower tiny stuff and some waves will push the faster tiny stuff. By looking at the number of slow and fast stuff we can help find out what pushed it. With our friends, computers who fly in space, we can see the different waves in space and see if it was where the tiny things rained into the top of the sky. Why do we study this? These tiny things can hurt our friends in space, both the computers as well as people in space and here in the world. We want to be able to know when this space rain will happen. But in order to know when these tiny tiny things will fall into the sky we have to first learn how to best look at and study them. Then we will know how often they rain down, where this space rain happens, and how large of an area this space rain falls in.

Standardization of barostat procedures for testing smooth muscle tone and sensory thresholds in the gastrointestinal tract. The Working Team of Glaxo-Wellcome Research, UK.

PubMed

Whitehead, W E; Delvaux, M

1997-02-01

An international working team of 13 investigators met on two occasions to develop guidelines for standardizing the procedures used to test gastrointestinal muscle tone and sensory thresholds using a barostat. General recommendations were: (1) Use a thin-walled plastic bag that is infinitely compliant until its capacity is reached. Maximum diameter of the bag should be much greater than the maximum diameter of the viscus. (2) The pump should be able to inflate the bag at up to 40 ml/sec. (3) Pressure should be monitored inside the bag, not in the pump or inflation line. (4) Subjects should be positioned so that the bag is close to the uppermost surface of the body. (5) For rectal tests, bowel cleansing should be limited to a tap water enema to minimize rectal irritation. Oral colonic lavage is recommended for studies of the proximal colon, and magnesium citrate enemas for the descending colon and sigmoid. (6) If sedation is required for colonic probe placement, allow at least one hour for drug washout and clearance of insufflated air. Ten to 20 min of adaptation before testing is adequate if no air or drugs were used. (7) The volumes reported must be corrected for the compressibility of gas and the compliance of the pump, which is greater for bellows pumps than for piston pumps. (8) Subjects should be tested in the fasted state. For evaluation of muscle tone: (9) The volume of the bag should be monitored for at least 15 min. For evaluation of sensory thresholds; (10) It is recommended that phasic distensions be > or = 60 sec long and that they be separated by > or = 60 sec. (11) Sensory thresholds should be reported as bag pressure rather than (or in addition to) bag volume because pressure is less vulnerable to measurement error. (12) Tests for sensory threshold should minimize psychological influences on perception by making the amount of each distension unpredictable to the subject. (13) Pain or other sensations should be reported on a graduated scale; not "yes-no." The working team recommends verbal descriptor scales, containing approximately seven steps, or visual analog scales in which subjects place a mark on a straight line marked "none" on one end and "maximum" on the other end. (14) It is recommended that subjects should be asked to rate the unpleasantness of distensions separately from their intensity.

Sampling of trace volatile metal(loid) compounds in ambient air using polymer bags: a convenient method.

PubMed

Haas, K; Feldmann, J

2000-09-01

The sampling of volatile metal(loid) compounds (VOMs) such as hydrides, methylated, and permethylated species of arsenic, antimony, and tin is described using Tedlar bags. Advantages as well as limitations and constraints are discussed and compared to other widely used sampling techniques within this area, namely, stainless steel canisters, cryotrapping, and solid adsorbent cartridges. To prove the suitability of Tedlar bags for the sampling of volatile metal(loid) compounds, series of stability tests have been run using both laboratory synthetic and real samples analyzed periodically after increasing periods of storage. The samples have been stored in the dark at 20 degrees C and at 50 degrees C. Various volatile arsenic species (AsH3, MeAsH2, Me2AsH, Me3As), tin species (SnH4, MeSnH3, Me2SnH2, Me3SnH, Me4Sn, BuSnH3), and antimony species (SbH3, MeSbH2, Me2SbH, Me3Sb) have been generated using hydride generation methodology and mixed with moisturized air. Three static gaseous atmospheres with concentrations of 0.3-18 ng/L for the various compounds have been generated in Tedlar bags, and the stability of the VOMs has been monitored over a period of 5 weeks. Sewage sludge digester gas samples have been stored only at 20 degrees C for a period of 48 h. Cryotrapping GC/ICPMS has been used for the determination of the VOMs with a relative standard deviation of 5% for 100 pg. After 8 h, the recovery rate of all the compounds in the air atmospheres was better than 95% at 20 and 50 degrees C, whereas the recovery after 24 h was found to be between 81 and 99% for all VOMs at 20 and 50 degrees C except for Me3Sb and Me3As. These species show a loss between 48 and 73% at both temperatures. After 5 weeks at 20 degrees C, a loss of only 25-50% for arsine and stibine and the above-mentioned tin compounds was determined. Only Me3Sb, Me3Bi, and Me2Te were present in the digester gas sample. After 24 h, losses of 44, 10, and 12%, respectively, could be determined. Given these results, Tedlar bags could even be used, with some limitations, for long-term sampling of air containing traces of VOMs. The loss is more pronounced at higher temperatures.

Integration of Pneumatic Technology in Powered Mobility Devices

PubMed Central

Daveler, Brandon; Wang, Hongwu; Gebrosky, Benjamin; Grindle, Garrett G.; Schneider, Urs

2017-01-01

Advances in electric motors, electronics, and control systems have enhanced the capability and drivability of electric power mobility devices over the last 60 years. Yet, battery technologies used in powered mobility devices (PMDs) have not kept pace. Recent advances in pneumatic technology, primarily the high torque, low speed design of rotary piston air motors, directly align with the needs of PMD. Pneumatic technology has advantages over battery-powered technology, including lighter weight, lower operating costs, decreased environmental impact, better reliability, and increased safety. Two prototypes were created that incorporated rotary piston air motors, high-pressure air tanks, and air-pressure regulators. Prototype 1 was created by modifying an existing electric PMD. Range tests were performed to determine the feasibility of pneumatic technology and the optimal combination of components to allow the longest range possible at acceptable speeds over ideal conditions. Using a 1.44 L air tank for feasibility testing, prototype 1 was capable of traveling 800 m, which confirmed the feasibility of pneumatic technology usage in PMDs. Prototype 2 was designed based on the testing results from prototype 1. After further optimization of prototype 2, the average maximum range was 3,150 m. Prototype 2 is up to 28.3% lighter than an equivalent size electric PMD and can be fully recharged in approximately 2 minutes. It decreases the cost of PMDs by approximately $1,500, because batteries do not need to be replaced over the lifetime of the device. The results provide justification for the use of pneumatic technology in PMDs. PMID:29339888

Integration of Pneumatic Technology in Powered Mobility Devices.

PubMed

Daveler, Brandon; Wang, Hongwu; Gebrosky, Benjamin; Grindle, Garrett G; Schneider, Urs; Cooper, Rory A

2017-01-01

Advances in electric motors, electronics, and control systems have enhanced the capability and drivability of electric power mobility devices over the last 60 years. Yet, battery technologies used in powered mobility devices (PMDs) have not kept pace. Recent advances in pneumatic technology, primarily the high torque, low speed design of rotary piston air motors, directly align with the needs of PMD. Pneumatic technology has advantages over battery-powered technology, including lighter weight, lower operating costs, decreased environmental impact, better reliability, and increased safety. Two prototypes were created that incorporated rotary piston air motors, high-pressure air tanks, and air-pressure regulators. Prototype 1 was created by modifying an existing electric PMD. Range tests were performed to determine the feasibility of pneumatic technology and the optimal combination of components to allow the longest range possible at acceptable speeds over ideal conditions. Using a 1.44 L air tank for feasibility testing, prototype 1 was capable of traveling 800 m, which confirmed the feasibility of pneumatic technology usage in PMDs. Prototype 2 was designed based on the testing results from prototype 1. After further optimization of prototype 2, the average maximum range was 3,150 m. Prototype 2 is up to 28.3% lighter than an equivalent size electric PMD and can be fully recharged in approximately 2 minutes. It decreases the cost of PMDs by approximately $1,500, because batteries do not need to be replaced over the lifetime of the device. The results provide justification for the use of pneumatic technology in PMDs.

Air injection test on a Kaplan turbine: prototype - model comparison

NASA Astrophysics Data System (ADS)

Angulo, M.; Rivetti, A.; Díaz, L.; Liscia, S.

2016-11-01

Air injection is a very well-known resource to reduce pressure pulsation magnitude in turbines, especially on Francis type. In the case of large Kaplan designs, even when not so usual, it could be a solution to mitigate vibrations arising when tip vortex cavitation phenomenon becomes erosive and induces structural vibrations. In order to study this alternative, aeration tests were performed on a Kaplan turbine at model and prototype scales. The research was focused on efficiency of different air flow rates injected in reducing vibrations, especially at the draft tube and the discharge ring and also in the efficiency drop magnitude. It was found that results on both scales presents the same trend in particular for vibration levels at the discharge ring. The efficiency drop was overestimated on model tests while on prototype were less than 0.2 % for all power output. On prototype, air has a beneficial effect in reducing pressure fluctuations up to 0.2 ‰ of air flow rate. On model high speed image computing helped to quantify the volume of tip vortex cavitation that is strongly correlated with the vibration level. The hydrophone measurements did not capture the cavitation intensity when air is injected, however on prototype, it was detected by a sonometer installed at the draft tube access gallery.

Bag-breakup control of surface drag in hurricanes

NASA Astrophysics Data System (ADS)

Troitskaya, Yuliya; Zilitinkevich, Sergej; Kandaurov, Alexander; Ermakova, Olga; Kozlov, Dmitry; Sergeev, Daniil

2016-04-01

Air-sea interaction at extreme winds is of special interest now in connection with the problem of the sea surface drag reduction at the wind speed exceeding 30-35 m/s. This phenomenon predicted by Emanuel (1995) and confirmed by a number of field (e.g., Powell, et al, 2003) and laboratory (Donelan et al, 2004) experiments still waits its physical explanation. Several papers attributed the drag reduction to spume droplets - spray turning off the crests of breaking waves (e.g., Kudryavtsev, Makin, 2011, Bao, et al, 2011). The fluxes associated with the spray are determined by the rate of droplet production at the surface quantified by the sea spray generation function (SSGF), defined as the number of spray particles of radius r produced from the unit area of water surface in unit time. However, the mechanism of spume droplets' formation is unknown and empirical estimates of SSGF varied over six orders of magnitude; therefore, the production rate of large sea spray droplets is not adequately described and there are significant uncertainties in estimations of exchange processes in hurricanes. Herewith, it is unknown what is air-sea interface and how water is fragmented to spray at hurricane wind. Using high-speed video, we observed mechanisms of production of spume droplets at strong winds by high-speed video filming, investigated statistics and compared their efficiency. Experiments showed, that the generation of the spume droplets near the wave crest is caused by the following events: bursting of submerged bubbles, generation and breakup of "projections" and "bag breakup". Statistical analysis of results of these experiments showed that the main mechanism of spray-generation is attributed to "bag-breakup mechanism", namely, inflating and consequent blowing of short-lived, sail-like pieces of the water-surface film. Using high-speed video, we show that at hurricane winds the main mechanism of spray production is attributed to "bag-breakup", namely, inflating and consequent breaking of short-lived, sail-like pieces of the water-surface film - "bags". On the base of general principles of statistical physics (model of a canonical ensemble) we developed statistics of the "bag-breakup" events: their number and statistical distribution of geometrical parameters depending on wind speed. Basing on the developed statistics, we estimated the surface stress caused by bags as the average sum of stresses caused by individual bags depending on their eometrical parameters. The resulting stress is subjected to counteracting impacts of the increasing wind speed: the increasing number of bags, and their decreasing sizes and life times and the balance yields a peaking dependence of the bag resistance on the wind speed: the share of bag-stress peaks at U10  35 m/s and then reduces. Peaking of surface stress associated with the "bag-breakup" explains seemingly paradoxical non-monotonous wind-dependence of surface drag coefficient peaking at winds about 35 m/s. This work was supported by the Russian Foundation of Basic Research (14-05-91767, 13-05-12093, 16-05-00839, 14-05-91767, 16-55-52025, 15-35-20953) and experiment and equipment was supported by Russian Science Foundation (Agreements 14-17-00667 and 15-17-20009 respectively), Yu.Troitskaya, A.Kandaurov and D.Sergeev were partially supported by FP7 Collaborative Project No. 612610.

A Water Cherenkov Detector prototype for the HAWC Gamma-Ray Observatory

NASA Astrophysics Data System (ADS)

Longo, Megan; Mostafa, Miguel; Salesa Greus, Francisco; Warner, David

2011-10-01

A full-size Water Cherenkov Detector (WCD) prototype for the High Altitude Water Cherenkov (HAWC) gamma-ray Observatory was deployed, and is currently being operated at Colorado State University (CSU). The HAWC Observatory will consist of 300 WCDs at the very high altitude (4100m) site in Sierra Negra, Mexico. Each WCD will have 4 baffled upward-facing Photomultiplier Tubes (PMTs) anchored to the bottom of a self made multilayer hermetic plastic bag containing 200,000 liters of purified water, inside a 5m deep by 7.3m diameter steel container. The full size WCD at CSU is the only full size prototype outside of the HAWC site. It is equipped with seven HAWC PMTs and has scintillators both under and above the volume of water. It has been in operation since March 1, 2011. This prototype also has the same laser calibration system that the detectors deployed at the HAWC site will have. The CSU WCD serves as a testbed for the different subsystems before deployment at high altitude, and for optimizing the location of the PMTs, the design of the light collectors, deployment procedures, etc. Simulations of the light inside the detectors and the expected signals in the PMTs can also be benchmarked with this prototype.

Muon data from a water Cherenkov detector prototype at Colorado State University

NASA Astrophysics Data System (ADS)

Longo, Megan; Mostafa, Miguel

2013-04-01

The High Altitude Water Cherenkov (HAWC) Observatory is a very high energy gamma-ray experiment currently under construction in Sierra Negra in the state of Puebla, Mexico, at an altitude of 4,100 m a.s.l. The HAWC Observatory will consist of 300 water Cherenkov detectors (WCDs), each instrumented with three 8'' photomultiplier tubes (PMTs) and one 10'' high efficiency (HE) PMT. The PMTs are upward facing, anchored to the bottom of a 5 m deep by 7.3 m diameter steel tank, containing a multilayer hermetic plastic bag holding 200,000 L of purified water. The only full size WCD prototype outside of the HAWC site is located at Colorado State University (CSU) in Fort Collins, CO at an altitude of 1,525 m a.s.l. This prototype is instrumented with six 8'' PMTs, one 10'' HE PMT, and the same laser calibration system, electronics, and data acquisition system as the WCDs at the HAWC site. The CSU prototype is additionally equipped with scintillator paddles both under and above the volume of water, temperature probes (in the water, outside, and in the DAQ room), and one covered PMT. Preliminary results for muon rates and their temperature dependance using data collected with the CSU prototype will be presented.

Automobile Crash Sensor Signal Processor

DOT National Transportation Integrated Search

1973-11-01

The crash sensor signal processor described interfaces between an automobile-installed doppler radar and an air bag activating solenoid or equivalent electromechanical device. The processor utilizes both digital and analog techniques to produce an ou...

40 CFR 63.8630 - What notifications must I submit and when?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Clay Ceramics Manufacturing...) For each APCD that includes a fabric filter, if a bag leak detection system is used, analysis and...

Collation of quarterly reports on air flat plate collectors

NASA Technical Reports Server (NTRS)

1977-01-01

The solar 2 air flat plate collectors are described. The development and fabrication of a prototype air flat plate collector subsystem containing 320 square feet of collector area are described. Three instrumented panels were completely assembled with glazing and insulation. Manufacture of the last seven prototype collectors was completed in October 1977.

Installation package - SIMS prototype system 1A

NASA Technical Reports Server (NTRS)

1976-01-01

This report consists of details for the installation, operation and maintenance of a prototype heating and hot water system, designed for residential or light commercial applications. This system consists of the following subsystems: air type collectors, pebble bed thermal storage, air handling unit, air to water heat exchanger, hot water preheat tank, auxiliary energy, ducting system.

Engineering with uncertainty: monitoring air bag performance.

PubMed

Wetmore, Jameson M

2008-06-01

Modern engineering is complicated by an enormous number of uncertainties. Engineers know a great deal about the material world and how it works. But due to the inherent limits of testing and the complexities of the world outside the lab, engineers will never be able to fully predict how their creations will behave. One way the uncertainties of engineering can be dealt with is by actively monitoring technologies once they have left the development and production stage. This article uses an episode in the history of automobile air bags as an example of engineers who had the foresight and initiative to carefully track the technology on the road to discover problems as early as possible. Not only can monitoring help engineers identify problems that surface in the field, it can also assist them in their efforts to mobilize resources to resolve problem.

Dynamic PIV measurement of a compressible flow issuing from an airbag inflator nozzle

NASA Astrophysics Data System (ADS)

Lee, Sang Joon; Jang, Young Gil; Kim, Seok; Kim, Chang Soo

2006-12-01

Among many equipment for passenger safety, the air bag system is the most fundamental and effective device for an automobile. The inflator housing is a main part of the curtain-type air bag system, which supplies high-pressure gases in pumping up the air bag-curtain which is increasingly being adapted in deluxe cars for protecting passengers from the danger of side clash. However, flow information on the inflator housing is very limited. In this study, we measure the instantaneous velocity fields of a high-speed compressible flow issuing from the exit nozzle of an inflator housing using a dynamic PIV system. From the velocity field data measured at a high frame-rate, we evaluate the variation of the mass flow rate with time. The dynamic PIV system consists of a high-repetition Nd:YLF laser, a high-speed CMOS camera, and a delay generator. The flow images are taken at 4000 fps with synchronization of the trigger signal for inflator ignition. From the instantaneous velocity field data of flow ejecting from the airbag inflator housing at the initial stage, we can see a flow pattern of broken shock wave front and its downward propagation. The flow ejecting from the inflator housing is found to have very high velocity fluctuations, with the maximum velocity at about 700 m/s. The time duration of the high-speed flow is very short, and there is no perceptible flow after 100 ms.

Biodigester Feasibility and Design for Space & Earth

NASA Technical Reports Server (NTRS)

Shutts, Stacy; Ewert, Mike; Bacon, Jack

2016-01-01

Anaerobic digestion converts organic waste into methane gas and fertilizer effluent. The ICA-developed prototype system is designed for planetary surface operation. It uses passive hydrostatic control for reliability, and is modular and redundant. The serpentine configuration accommodates tight geometric constraints similar to the ISS ECLSS rack architectures. Its shallow, low-tilt design enables (variable) lower-g convection than standard Earth (1 g) digesters. This technology will reuse and recycle materials including human waste, excess food, as well as packaging (if biodegradable bags are used).

Development approach to an enterprise-wide medication reconciliation tool in a free-standing pediatric hospital with commercial best-of-breed systems.

PubMed

Yu, Feliciano B; Leising, Scott; Turner, Scott

2007-10-11

Medication reconciliation is essential to providing a safer patient environment during transitions of care in the clinical setting. Current solutions include a mixed-bag of paper and electronic processes. Best-of-breed health information systems architecture poses a specific challenge to organizations that have limited software development resources. Using readily available service-oriented technology, a prototype for an integrated medication reconciliation tool is developed for use in an academic pediatric hospital with commercial systems.

A chlorate candle/lithium hydroxide personal breathing apparatus

NASA Technical Reports Server (NTRS)

Martin, F. E.

1972-01-01

A portable coal mine rescue and survival equipment is reported that consists of a chlorate candle with a lithium hydroxide carbon-dioxide absorbent for oxygen generation, a breathing bag and tubing to conduct breathing to and from the man. A plastic hood incorporating a mouth piece for communication provides also eye protection and prevents inhalation through the nose. Manned testing of a prototype system demonstrated the feasibility of this closed circuit no-maintenance breathing apparatus that provides for good voice communication.

Landing Characteristics of a Reentry Capsule with a Torus-Shaped Air Bag for Load Alleviation

NASA Technical Reports Server (NTRS)

McGehee, John R.; Hathaway, Melvin E.

1960-01-01

An experimental investigation has been made to determine the landing characteristics of a conical-shaped reentry capsule by using torus-shaped air bags for impact-load alleviation. An impact bag was attached below the large end of the capsule to absorb initial impact loads and a second bag was attached around the canister to absorb loads resulting from impact on the canister when the capsule overturned. A 1/6-scale dynamic model of the configuration was tested for nominal flight paths of 60 deg. and 90 deg. (vertical), a range of contact attitudes from -25 deg. to 30 deg., and a vertical contact velocity of 12.25 feet per second. Accelerations were measured along the X-axis (roll) and Z-axis (yaw) by accelerometers rigidly installed at the center of gravity of the model. Actual flight path, contact attitudes, and motions were determined from high-speed motion pictures. Landings were made on concrete and on water. The peak accelerations along the X-axis for landings on concrete were in the order of 3Og for a 0 deg. contact attitude. A horizontal velocity of 7 feet per second, corresponding to a flight path of 60 deg., had very little effect upon the peak accelerations obtained for landings on concrete. For contact attitudes of -25 deg. and 30 deg. the peak accelerations along the Z-axis were about +/- l5g, respectively. The peak accelerations measured for the water landings were about one-third lower than the peak accelerations measured for the landings on concrete. Assuming a rigid body, computations were made by using Newton's second law of motion and the force-stroke characteristics of the air bag to determine accelerations for a flight path of 90 deg. (vertical) and a contact attitude of 0 deg. The computed and experimental peak accelerations and strokes at peak acceleration were in good agreement for the model. The special scaling appears to be applicable for predicting full-scale time and stroke at peak acceleration for a landing on concrete from a 90 deg. flight path at a 0 deg. It appears that the full-scale approximately the same as those obtained from the model for the range of attitudes and flight paths investigated.

Evaluation of prototype air carrier instrument approach procedure charts.

DOT National Transportation Integrated Search

1995-07-31

The objective of this study was to evaluate the design features of two prototype Instrument Approach Procedure (IAP) charts. The John A. Volpe National Transportation System's Center in cooperation with the Air Transport Association's Chart and Data ...

Evaluation of prototype air carrier instrument approach procedure charts

DOT National Transportation Integrated Search

1995-07-01

The objective of this study was to evaluate the design features of two prototype Instrument Approach Procedure (IAP) charts. The John A. Volpe National Transportation Systems Center in cooperation with the Air Transport Association's Chart and Data D...

Environmental Assessment for Capital Improvement Projects, Buckley Air Force Base, Colorado. Volume 2 of 2

DTIC Science & Technology

2006-03-01

2003 Air Emission Inventory, July 2004. o The generators are assumed to be diesel-fired and have a horsepower rating of less than 600 hp. o...In July 2003, the 460th LRS purchased and installed an automated movable storage system for mobility bag storage. This system eliminates wasted aisle...Installation Restoration Program Draft Final Engineering Evaluation/Cost Analysis IRP Site 4. July . • URS Corporation (URS). 2003a. Buckley Air Force

Reduction of Urinary Tract Infections Caused By Urethral Catheter through the Implementation of Hydrophobic Coating and Geometrical Modifications

NASA Astrophysics Data System (ADS)

Gare, Aya

2013-11-01

Catheter-Associated Urinary Tract Infection (CAUTI) is the most common nosocomial infection in the U.S. healthcare system. The obstruction of urine caused by confined air bubbles result in the development of urinary back-flow and stagnation, wherein microbial pathogens could multiply rapidly and colonization within catheters become commonplace. Infections can be prevented by aseptic insertion and the maintenance of a closed drainage system, keeping high infection control standards, and preventing back-flow from the catheter bag. The goal of this study is to assess the effectiveness of a simple, low cost, modification that may be implemented into current catheter designs to reduce the incidence of CAUTI. Using the principle of transmission of fluid-pressure and the Young-Laplace equation for capillary pressure difference, this research focuses on improving the liquid flow in the presence of confined bubbles to prevent stagnation and reflux of bacteria-ridden urine into the body. Preliminary experiments are performed on a variety of tubes with hydrophobic-coating the interior, as well as geometrically modifying the tubes. Proof-of-Concept Prototype tubes are used to represent the drainage system of the catheter structure.

A Portable Electronic Nose for Toxic Vapor Detection, Identification, and Quantification

NASA Technical Reports Server (NTRS)

Linnell, B. R.; Young, R. C.; Griffin, T. P.; Meneghelli, B. J.; Peterson, B. V.; Brooks, K. B.

2005-01-01

The Space Program and military use large quantities of hydrazine and monomethyl hydrazine as rocket propellant, which are very toxic and suspected human carcinogens. Current off-the-shelf portable instruments require 10 to 20 minutes of exposure to detect these compounds at the minimum required concentrations and are prone to false positives, making them unacceptable for many operations. In addition, post-mission analyses of grab bag air samples from the Shuttle have confirmed the occasional presence of on-board volatile organic contaminants, which also need to be monitored to ensure crew safety. A new prototype instrument based on electronic nose (e-nose) technology has demonstrated the ability to qualify (identify) and quantify many of these vapors at their minimum required concentrations, and may easily be adapted to detect many other toxic vapors. To do this, it was necessary to develop algorithms to classify unknown vapors, recognize when a vapor is not any of the vapors of interest, and estimate the concentrations of the contaminants. This paper describes the design of the portable e-nose instrument, test equipment setup, test protocols, pattern recognition algorithms, concentration estimation methods, and laboratory test results.

Putting Children First

DOT National Transportation Integrated Search

2000-01-01

This document focuses on what has been and what still needs to be done to protect children from death or injury in transportation-related crashes. The following issues areas are examined: air bags and children, permanent child safety seat fitting sta...

49 CFR 585.13 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Applicability. 585.13 Section 585.13 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase...

49 CFR 585.13 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Applicability. 585.13 Section 585.13 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase...

49 CFR 585.13 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Applicability. 585.13 Section 585.13 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase...

49 CFR 585.13 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Applicability. 585.13 Section 585.13 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase...

49 CFR 585.13 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Applicability. 585.13 Section 585.13 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PHASE-IN REPORTING REQUIREMENTS Advanced Air Bag Phase...

Reviews Toy: Air swimmers Book: Their Arrows will Darken the Sun: The Evolution and Science of Ballistics Book: Physics Experiments for your Bag Book: Quantum Physics for Poets Equipment: SEP colour wheel kit Equipment: SEP colour mixing kit Software: USB DrDAQ App: iHandy Level Equipment: Photonics Explorer kit Web Watch

NASA Astrophysics Data System (ADS)

2012-01-01

WE RECOMMEND Air swimmers Helium balloon swims like a fish Their Arrows will Darken the Sun: The Evolution and Science of Ballistics Ballistics book hits the spot Physics Experiments for your Bag Handy experiments for your lessons Quantum Physics for Poets Book shows the economic importance of physics SEP colour wheel kit Wheels investigate colour theory SEP colour mixing kit Cheap colour mixing kit uses red, green and blue LEDs iHandy Level iPhone app superbly measures angles Photonics Explorer kit Free optics kit given to schools WORTH A LOOK DrDAQ DrDAQ software gets an upgrade WEB WATCH Websites show range of physics

Investigation of compaction and permeability during the out-of-autoclave and vacuum-bag-only manufacturing of a laminate composite with aligned carbon nanofibers

NASA Astrophysics Data System (ADS)

Mann, Erin

Both industry and commercial entities are in the process of using more lightweight composites. Fillers, such as fibers, nanofibers and other nanoconstituents in polymer matrix composites have been proven to enhance the properties of composites and are still being studied in order to optimize the benefits. Further optimization can be studied during the manufacturing process. The air permeability during the out-of-autoclave-vacuum-bag-only (OOA-VBO) cure method is an important property to understand during the optimization of manufacturing processes. Changes in the manufacturing process can improve or decrease composite quality depending on the ability of the composite to evacuate gases such as air and moisture during curing. Therefore, in this study, the axial permeability of a prepreg stack was experimentally studied. Three types of samples were studied: control (no carbon nanofiber (CNF) modification), unaligned CNF modified and aligned CNF modified samples.

Pilot Perception of Electronic Flight Bags at Part 121 Air Carriers

NASA Astrophysics Data System (ADS)

Lytle, Donley

Electronic Flight Bags (EFBs) have been approved for use by pilots in flight operations at many Part 121 air carriers in the United States since 2010. As an automated device replacing paper in the cockpit, there are many human factor issues that relate to operation of the EFB. EFBs have been cited in accidents and incidents worldwide in large, transport category aircraft. While the EFB was not cited as the main cause of the accident/incident, it has been listed as a contributing factor. This study looks at pilot perception related to the safety aspect of the EFB in flight operations at Part 121 carriers in the United States. It surveys pilots that utilize the device in daily, routine flight operations to determine their perception of the EFB. The study is followed with a survey of a small group of pilots to help explain the results and any correlation between the variables.

Final Report for Intravenous Fluid Generation (IVGEN) Spaceflight Experiment

NASA Technical Reports Server (NTRS)

McQuillen, John B.; McKay, Terri L.; Griffin, DeVon W.; Brown, Dan F.; Zoldak, John T.

2011-01-01

NASA designed and operated the Intravenous Fluid Generation (IVGEN) experiment onboard the International Space Station (ISS), Increment 23/24, during May 2010. This hardware was a demonstration experiment to generate intravenous (IV) fluid from ISS Water Processing Assembly (WPA) potable water using a water purification technique and pharmaceutical mixing system. The IVGEN experiment utilizes a deionizing resin bed to remove contaminants from feedstock water to a purity level that meets the standards of the United States Pharmacopeia (USP), the governing body for pharmaceuticals in the United States. The water was then introduced into an IV bag where the fluid was mixed with USP-grade crystalline salt to produce USP normal saline (NS). Inline conductivity sensors quantified the feedstock water quality, output water purity, and NS mixing uniformity. Six 1.5-L bags of purified water were produced. Two of these bags were mixed with sodium chloride to make 0.9 percent NS solution. These two bags were returned to Earth to test for compliance with USP requirements. On-orbit results indicated that all of the experimental success criteria were met with the exception of the salt concentration. Problems with a large air bubble in the first bag of purified water resulted in a slightly concentrated saline solution of 117 percent of the target value of 0.9 g/L. The second bag had an inadequate amount of salt premeasured into the mixing bag resulting in a slightly deficient salt concentration of 93.8 percent of the target value. The USP permits a range from 95 to 105 percent of the target value. The testing plans for improvements for an operational system are also presented.

Effects of air exchange property of passive-type radon-thoron discriminative detectors on performance of radon and thoron measurements.

PubMed

Omori, Y; Janik, M; Sorimachi, A; Ishikawa, T; Tokonami, S

2012-11-01

Pairs of diffusion chambers with different air exchange rates are used in a large-scale survey to determine radon and thoron, separately. When they are enclosed in radon-proof bags for keeping after the exposure, since radon does not escape out immediately from the low-diffusion chamber, it leads to further exposure in the bags and disturbs the estimation of radon and thoron concentrations. In this study, the effects of the different air exchange properties of the radon-thoron discriminative detectors with CR-39 chips on the estimations of radon and thoron concentrations were investigated. The commercially available and frequently used detectors, Raduet, are examined in this study. The result shows that radon escapes out in 10 h. When degassing is not enough after the exposure in a calibration experiment or high-background radiation area, the residual radon causes the overestimation of the radon concentration and increase in the uncertainty in the thoron concentration, i.e. a low-performance quality of radon and thoron measurements.

Traffic contribution to air pollution in urban street canyons: Integrated application of the OSPM, moss biomonitoring and spectral analysis

NASA Astrophysics Data System (ADS)

Lazić, Lazar; Urošević, Mira Aničić; Mijić, Zoran; Vuković, Gordana; Ilić, Luka

2016-09-01

To investigate the air pollutant distribution within the ambient of urban street canyon, Operational Street Pollution Model (OSPM) was used to predict hourly content of NOX, NO, NO2, O3, CO, BNZ and PM10. The study was performed in five street canyons in Belgrade (Serbia) during 10-week summer period. The model receptors were located on each side of street canyons at 4 m, 8 m and 16 m height. To monitor airborne trace element content, the moss bag biomonitors were simultaneously exposed with the model receptors at two heights-4 m and 16 m. The results of both methods, modelling and biomonitoring, showed significantly decreasing trend of the air pollutants with height. The results indirectly demonstrate that biomonitoring, i.e., moss bag technique could be a valuable tool to verify model performance. In addition, spectral analysis was applied to investigate weekly variation of the daily background and modelled data set. Typical periodicities and weekend effect, caused by anthropogenic influences, have been identified.

Development and Analysis of Desiccant Enhanced Evaporative Air Conditioner Prototype

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kozubal, E.; Woods, J.; Judkoff, R.

2012-04-01

This report documents the design of a desiccant enhanced evaporative air conditioner (DEVAP AC) prototype and the testing to prove its performance. Previous numerical modeling and building energy simulations indicate a DEVAP AC can save significant energy compared to a conventional vapor compression AC (Kozubal et al. 2011). The purposes of this research were to build DEVAP prototypes, test them to validate the numerical model, and identify potential commercialization barriers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crandall, M.S.; Wilcox, T.G.

An evaluation was made of working conditions at the Graphic Packaging Corporation, Paoli, Pennsylvania. Particular attention was given to workers making microwave popcorn bags who reported swelling around the eyes and dermatitis. One employee also reported an asthma attack while working on the bags. Special water-based epoxy adhesives were used for these bags as the product must withstand heating in a microwave oven. Environmental and personal breathing-zone air samples were taken and medical questionnaires were filled out. Use of the adhesive was discontinued in May of 1987 and the symptoms have disappeared. Chemical analysis of the adhesive indicated the presencemore » of several chemicals that are potential irritants or allergic sensitizers both to skin and the respiratory tract. These irritants included formaldehyde, acetaldehyde, benzoic acid, 1,1,1-trichloroethane, p-dioxane, and ethyl acetate. Samples taken before the switchover to another adhesive was made did not indicate a hazardous level of any of these substances to be present.« less

2007 motor vehicle occupant safety survey. Volume 3, air bags report

DOT National Transportation Integrated Search

2008-11-01

The 2007 Motor Vehicle Occupant Safety Survey was the sixth in a series of periodic national telephone surveys on occupant : protection issues conducted for the National Highway Traffic Safety Administration (NHTSA). Data collection was conducted : b...

Techniques for Developing Child Dummy Protection Reference Values. Event Report

DOT National Transportation Integrated Search

1996-10-01

The purpose of this report is to present background information and techniques : for developing protection reference values (PRV) to use with child dummies in : out-of-position (OOP) child/air bag interaction testing. Biomechanics experts : agree tha...

May 2004 Click It or Ticket seat belt mobilization evaluation

DOT National Transportation Integrated Search

2007-05-01

The National Highway Traffic Safety Administration and the Air : Bag & Seat Belt Safety Campaign of the National Safety Council, : in conjunction with thousands of State and local law enforcement : agencies, conduct annual national seat belt mobiliza...

Special Feature: Automotive Technology.

ERIC Educational Resources Information Center

Wagner, Margaret; And Others

1993-01-01

Includes "National Trouble Shooting Contest--Training Technicians, Not Mechanics" (Wagner); "Front Wheel Drive on a Small Scale" (Waggoner); "Air Bags in Hit and Run on Rack and Pinion Technicians" (Collard); and "Future Technology--A Blind Spot Detector for Highway Driving" (Zoghi, Bellubi). (JOW)

Up, Up and Away.

ERIC Educational Resources Information Center

Markle, Sandra

1988-01-01

Kite flying as a fun class project is proposed as a way of letting students apply what they've learned about air. A design for a kite made from a trash bag is provided, as are kite flying tips and resources. (MT)

Improved Whole-Blood-Staining Device

NASA Technical Reports Server (NTRS)

Sams, Clarence F.; Crucian, Brian; Paul, Bonnie; Melton, Shannon; Guess, Terry

2012-01-01

Dramatic improvements have been made in NASA s Whole Blood Staining Device (WBSD) since it was last described in "Whole-Blood-Staining Device," NASA Tech Briefs, Vol. 23, No. 10 (October 1999), page 64. The new system has a longer shelf life, a simpler and more effective operational procedure, improved interface with instrumentation, and shorter processing time. More specifically, the improvements have targeted bag and locking clip materials, sampling ports, and air pocket prevention. The WBSD stains whole blood collected during spaceflight for subsequent flow cytometric analysis. In short, the main device stains white blood cells by use of monoclonal antibodies conjugated to various fluorochromes, followed by lysing and fixing of the cells by use of a commercial reagent that has been diluted according to NASA safety standards. This system is compact, robust, and does not require electric power, precise mixing, or precise incubation times. Figure 1 depicts the present improved version for staining applications, which is a poly(tetrafluoroethylene) bag with a Luer-lock port and plastic locking clips. An InterLink (or equivalent) intravenous- injection port screws into the Luer-lock port. The inflatable/collapsible nature of the bag facilitates loading and helps to minimize the amount of air trapped in the fully loaded bag. Some additional uses have been identified for the device beyond whole blood staining. The WBSD has been configured for functional assays that require culture of live cells by housing sterile culture media, mitogens, and fixatives prior to use [Figure 2(a)]. Simple injection of whole blood allows cell-stimulation culture to be performed in reduced gravity conditions, and product stabilization prior to storage, while protecting astronauts from liquid biohazardous materials. Also, the improved WBSD has reconstituted powdered injectable antibiotics by mixing them with diluent liquids [Figure 2(b)]. Although such mixing can readily be performed on Earth by shaking in glass vials, it cannot readily be performed this way in outer space without entraining air bubbles. The present device can be preloaded with the powder and diluent(s) in separate compartments. The powder and diluent( s) can be mixed, without introducing air bubbles, by removing the clip(s), then shaking. This use of the device could also be advantageous in terrestrial applications because it maintains the isolation of the constituents until the time of use.

Forces on intraocular lens haptics induced by capsular fibrosis. An experimental study.

PubMed

Guthoff, R; Abramo, F; Draeger, J; Chumbley, L C; Lang, G K; Neumann, W

1990-01-01

Electronic dynamometry measurements, performed upon intraocular lens (IOL) haptics of prototype one-piece three-loop silicone lenses, accurately defined the relationships between elastic force and haptic displacement. Lens implantations in the capsular bag of dogs (loop span equal to capsular bag diameter, loops underformed immediately after the operation) were evaluated macrophotographically 5-8 months postoperatively. The highly constant elastic property of silicon rubber permitted quantitative correlation of subsequent in vivo haptic displacement with the resultant force vectors responsible for tissue contraction. The lens optics were well centered in 17 (85%) and slightly offcenter in 3 (15%) of 20 implanted eyes. Of the 60 supporting loops, 28 could be visualized sufficiently well to permit reliable haptic measurement. Of these 28, 20 (71%) were clearly displaced, ranging from 0.45 mm away from to 1.4 mm towards the lens' optic center. These extremes represented resultant vector forces of 0.20 and 1.23 mN respectively. Quantitative vector analysis permits better understanding of IOL-capsular interactions.

Measurement of Civil Engineering Customer Satisfaction in Tactical Air Command: A Prototype Evaluation Program.

DTIC Science & Technology

1986-09-01

customers . The article states that in response to a White House Office of Consumer Affairs study and with the wide use of minicomputers: Companies are...D-A174 l16 MEASUREMENT OF CIVIL ENGINEERING CUSTOMER SRTISFACTIbN 1/ IN TACTICAL AIR CO (U) AIR FORCE INST OF TECH ...... RIGHT-PATTERSON AFB ON...BUREAU OF STANDARDS- 1963-A_ . -_- ’II I-F MEASUREMENT OF CIVIL ENGINEERING CUSTOMER SATISFACTION IN TACTICAL AIR COMMAND: A PROTOTYPE EVALUATION PROGRAM

Thermographic Analysis of Composite Cobonds on the X-33

NASA Technical Reports Server (NTRS)

Russell, S. S.; Walker, J. L.; Lansing, M. D.

2001-01-01

During the manufacture of the X-33 liquid hydrogen (LH2) Tank 2, a total of 36 reinforcing caps were inspected thermographically. The cured reinforcing sheets of graphite/epoxy were bonded to the tank using a wet cobond process with vacuum bagging and low temperature curing. A foam filler material wedge separated the reinforcing caps from the outer skin of the tank. Manufacturing difficulties caused by a combination of the size of the reinforcing caps and their complex geometry lead to a potential for trapping air in the bond line. An inspection process was desired to ensure that the bond line was free of voids before it had cured so that measures could be taken to rub out the entrapped air or remove the cap and perform additional surface matching. Infrared thermography was used to perform the procure 'wet bond' inspection as well a to document the final 'cured' condition of the caps. The thermal map of the bond line was acquired by heating the cap with either a flash lamp or a set of high intensity quartz lamps and then viewing it during cool down. The inspections were performed through the vacuum bag and voids were characterized by localized hot spots. In order to ensure that the cap had bonded to the tank properly, a post cure 'flash heating' thermographic investigation was performed with the vacuum bag removed. Any regions that had opened up after the preliminary inspection or that were hidden during the bagging operation were marked and filled by drilling small holes in the cap and injecting resin. This process was repeated until all critical sized voids were filled.

Lamella dissolved air flotation treatment of fish farming effluents as a part of an integrated farming and effluent treatment concept.

PubMed

Jokela, Petri; Lepistö, Raghida

2014-01-01

Nutrient emissions from fish farming can be reduced by a bag pen, i.e., a floating circular basin which serves simultaneously both as a fish cultivation tank and a swirl separation tank. Solid matter (excreta and uneaten feed) is collected at the bottom of the bag pen and pumped as an underflow to a dissolved air flotation (DAF) unit for nutrient removal. DAF equipped with lamella elements was studied in real conditions. Altogether 3000 rainbow trout females (2.0 kg each) were cultivated. Solid-water mixture was pumped from the bottom of the bag pen to an equalizing basin using a sequence of 2-min pumping followed by a 4-min pause. In some tests the influent was pumped directly and continuously from the bag pen to DAF. The influent quality changed substantially: average suspended solids (SS) and phosphorus (P) concentrations were 290 mg l⁻¹ ± 110 mg l⁻¹ and 3.2 mg l⁻¹ ± 1.2 mg l⁻¹, respectively. When the influent was fresh and P strongly associated with SS, DAF without precipitation chemicals produced up to 86% SS and 83% P removals. The influence of chemical doses was studied using 6.4-29.2 mg Fe l⁻¹ with hydraulic loadings (HLs) of 11.0-11.7 m h⁻¹. SS and P removal did not change substantially and the effluent concentration levelled at 30 mg SS l⁻¹ and 0.20-0.30 mg P l⁻¹, respectively. The lamella DAF, coupled with ferric precipitation, produced up to 90% P and 80% nitrogen reductions. HLs, excluding recycle water flow and lamella projection, up to 21 m h⁻¹ could be used.

Thermographic Analysis of Composite Cobonds on the X-33

NASA Technical Reports Server (NTRS)

Russell, Samuel S.; Walker, James L.; Lansing, Matthew D.; Whitaker, Ann F. (Technical Monitor)

2000-01-01

During the manufacture of the X-33 liquid hydrogen (LH2) Tank 2, a total of thirty-six reinforcing caps were inspected thermographically. The cured reinforcing sheets of graphite/epoxy were bonded to the tank using a wet cobond process with vacuum bagging and low temperature curing. A foam filler material wedge separated the reinforcing caps from the outer skin of the tank. Manufacturing difficulties caused by a combination of the size of the reinforcing caps and their complex geometry lead to a potential for trapping air in the bond line. An inspection process was desired to ensure that the bond line was free of voids before it had cured so that measures could be taken to rub out the entrapped air or remove the cap and perform additional surface matching. Infrared thermography was used to perform the precure "wet bond" inspection as well as to document the final "cured" condition of the caps. The thermal map of the bond line was acquired by heating the cap with either a flash lamp or a set of high intensity quartz lamps and then viewing it during cool down. The inspections were performed through the vacuum bag and voids were characterized by localized hot spots. In order to ensure that the cap had bonded to the tank properly, a post cure "flash heating" thermographic investigation was performed with the vacuum bag removed. Any regions that had opened up after the preliminary inspection or that were hidden during the bagging operation were marked and filled by drilling small holes in the cap and injecting resin. This process was repeated until all critical sized voids were filled.

Influence of mask type and mask position on the effectiveness of bag-mask ventilation in a neonatal manikin.

PubMed

Deindl, Philipp; O'Reilly, Megan; Zoller, Katharina; Berger, Angelika; Pollak, Arnold; Schwindt, Jens; Schmölzer, Georg M

2014-01-01

Anatomical face mask with an air cushion rim might be placed accidentally in a false orientation on the newborn's face or filled with various amounts of air during neonatal resuscitation. Both false orientation as well as variable filling may reduce a tight seal and therefore hamper effective positive pressure ventilation (PPV). We aimed to measure the influence of mask type and mask position on the effectiveness of PPV. Twenty neonatal staff members delivered PPV to a modified, leak-free manikin. Resuscitation parameters were recorded using a self-inflatable bag PPV with an Intersurgical anatomical air cushion rim face mask (IS) and a size 0/1 Laerdal round face mask. Three different positions of the IS were tested: correct position, 90° and 180° rotation in reference to the midline of the face. IS masks in each correct position on the face but with different inflation of the air cushion (empty, 10, 20 and 30 mL). Mask leak was similar with mask rotation to either 90° or 180° but significantly increased from 27 (13-73) % with an adequate filled IS mask compared to 52 (16-83) % with an emptied air cushion rim. Anatomical-shaped face mask had similar mask leaks compared to round face mask. A wrongly positioned anatomical-shaped mask does not influence mask leak. Mask leak significantly increased once the air cushion rim was empty, which may cause failure in mask PPV.

Techniques for developing child dummy protection reference values : event report

DOT National Transportation Integrated Search

1996-10-01

The purpose of this report is to present background information and techniques for developing protection reference values (PRV) to use with child dummies in out-of-position (OOP) child/air bag interaction testing. This report summarizes the literatur...

STS-28 Columbia, OV-102, Commander Shaw on middeck

NASA Technical Reports Server (NTRS)

1989-01-01

At open middeck stowage locker, Commander Brewster H. Shaw pauses to have his picture taken. Behind Shaw on port side wall are solid sorbent air sampler, a plastic storage bag filled with wheat crackers, and various food and beverage containers.

Safety Belt Use: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, discusses traffic safety tips for wearing seat belts. It describes the correct way to wear a seat belt, how to sit, and differentiates between lap belts and shoulder belts. It points out that air bags provid...

40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... simulates testing in an environmental test cell (see § 86.162-00 (a) for a discussion of simulation... exhaust and dilution air bag samples to the analytical system and process the samples according to § 86...

Determination of frontal offset test conditions based on crash data

DOT National Transportation Integrated Search

1998-01-01

This paper reports on the test procedure development : phase of the agencys Improved Frontal Protection : research program. It is anticipated that even after all cars : and light trucks have air bags for drivers and front seat : passengers there w...

2000 motor vehicle occupant safety survey. Volume 3, Air bags report

DOT National Transportation Integrated Search

2001-09-01

The 2000 Motor Vehicle Occupant Safety Survey was the fourth in a series of biennial national telephone surveys on occupant protection issues conducted for the National Highway Traffic Safety Administration (NHTSA). Data collection was conducted by S...

Effect of Bioactive Glass air Abrasion on Shear Bond Strength of Two Adhesive Resins to Decalcified Enamel

PubMed Central

Eshghi, Alireza; Khoroushi, Maryam; Rezvani, Alireza

2014-01-01

Objective: Bioactive glass air abrasion is a conservative technique to remove initial decalcified tissue and caries. This study examined the shear bond strength of composite resin to sound and decalcified enamel air-abraded by bioactive glass (BAG) or alumina using etch-and-rinse and self-etch adhesives. Materials and Methods: Forty-eight permanent molars were root-amputated and sectioned mesiodistally. The obtained 96 specimens were mounted in acrylic resin; the buccal and lingual surfaces remained exposed. A demineralizing solution was used to decalcify half the specimens. Both sound and decalcified specimens were divided into two groups of alumina and bioactive glass air abrasion. In each group, the specimens were subdivided into two subgroups of Clearfil SE Bond or OptiBond FL adhesives (n=12). Composite resin cylinders were bonded on enamel surfaces cured and underwent thermocycling. The specimens were tested for shear bond strength. Data were analyzed using SPSS 16.0 and three-way ANOVA (α=0.05). Similar to the experimental groups, the enamel surface of one specimen underwent SEM evaluation. Results: No significant differences were observed in composite resin bond strength subsequent to alumina or bioactive glass air abrasion preparation techniques (P=0.987). There were no statistically significant differences between the bond strength of etch-and-rinse and self-etch adhesive groups (P=1). Also, decalcified or intact enamel groups had no significant difference (P=0.918). However, SEM analysis showed much less enamel irregularities with BAG air abrasion compared to alumina air abrasion. Conclusion: Under the limitations of this study, preparation of both intact and decalcified enamel surfaces with bioactive glass air abrasion results in similar bond strength of composite resin in comparison with alumina air abrasion using etch-&-rinse or self-etch adhesives. PMID:25628694

Flow-Meter and Passive Diffusion Bag Tests and Potential Influences on the Vertical Distribution of Contaminants in Wells at Galena Airport, Galena, Alaska, August to October 2002

USGS Publications Warehouse

Vroblesky, Don A.; Peterson, J.E.

2004-01-01

Past activities at Galena Airport, a U.S. Air Force Base in Galena, Alaska, have resulted in ground-water contamination by volatile organic compounds. The primary contaminants are petroleum hydrocarbons and chlorinated aliphatic hydrocarbons. The U.S. Geological Survey and Earth Tech, in cooperation with the Air Force Center for Environmental Excellence, conducted investigations at Galena Airport from August to October 2002 using polyethylene diffusion bag samplers and borehole flow-meter testing to examine the vertical distribution of ground-water contamination in selected wells. This investigation was limited to the vicinity of building 1845 and to the area between building 1845 and the Yukon River. In addition, the U.S. Geological Survey was asked to determine whether additional wells are needed to more clearly define the nature and extent of the ground-water contamination at the Air Force Base. Little or no vertical water movement occurred under ambient conditions in the wells tested at Galena Airport, Alaska, in August 2002. All of the ambient vertical flows detected in wells were at rates less than the quantitative limit of the borehole flow meter (0.03 gallons per minute). In wells 06-MW-07 and 10-MW-01, no vertical flow was detected. In wells where ambient flow was detected, the direction of flow was downward. In general, concentrations of volatile organic compounds detected in the low-flow samples from wells at Galena Airport were approximately the same concentrations detected in the closest polyethylene diffusion bag sample for a wide variety of volatile organic compounds. The data indicate that the polyethylene diffusion bag sample results are consistent with the low-flow sample results. Vertical profiling of selected wells using polyethylene diffusion bag samplers at Galena Airport showed that from September 30 to October 1, 2002, little vertical change occurred in volatile organic compound concentrations along the screen length despite the fact that little or no vertical flow was measured in most of the tested wells in August 2002. Two of the wells (10-MW-03 and 06-MW-01) had slightly greater vertical concentration variation for some constituents. In these wells, the contaminant depth probably is lithologically influenced. The close match between concentrations measured in polyethylene diffusion bag and low-flow samples indicates that the bag samples accurately represent the distribution of volatile organic compounds in the wells. It is unclear, however, whether the distribution of volatile organic compounds in the wells, as indicated by the bag samplers, represents contaminant distributions in the aquifer or transient movement within the wells. The probable change in well hydraulics between August and late September to October indicates that the relatively uniform vertical distribution of volatile organic compounds in some of the wells may represent in-well mixing. This uncertainty could be clarified by the installation and sampling of well clusters at various times of the year. Additional insight into the vertical distribution of contamination and flow possibly could be obtained by conducting flow-meter tests and collecting polyethylene diffusion bag samples from selected wells at different times of the year. The westernmost contaminant plume at Million Gallon Hill appears to be surrounded by sufficient monitoring wells to detect changes in the plume extent; however, the installation of additional wells at Galena Airport has the potential to provide additional information on the extent of ground-water contamination in the remaining plumes. The additional information to be gained includes better definition of the vertical and lateral extents of the plumes and better definition of the ground-water flow directions.

STS-32 OV-102 air revitalization system (ARS) humidity separator problem

NASA Technical Reports Server (NTRS)

1990-01-01

During STS-32, onboard Columbia, Orbiter Vehicle (OV) 102, a leakage problem at environmental control and life support system (ECLSS) air revitalization system (ARS) humidity separator A below the middeck is documented in this closeup view. Note the many bubbles around the separator. The crew cleared out stowage bags, lithium hydroxide (LiOH) cannisters and other materials to get at the problem. It was eventually repaired.

Portable Intravenous Fluid Production Device For Ground Use Project

NASA Technical Reports Server (NTRS)

Oliva-Buisson, Yvette J.

2014-01-01

Several medical conditions require the administration of intravenous (IV) fluids,but limitations of mass, volume, shelf-life, transportation, and local resources can restrict the availability of these important fluids. Such limitations are expected in long-duration space exploration missions and in remote or austere places on Earth. This design uses regular drinking water that is pumped through two filters to produce, in minutes, sterile, ultrapure water that meets the stringent quality standards of the United States Pharmacopeia for Water for Injection (Total Bacteria, Conductivity, Endo - toxins, Total Organic Carbon). The device weighs 2.2 lb (1 kg) and is 10 in. long, 5 in. wide, and 3 in. high (˜25, 13, and 7.5 cm, respectively) in its storage configuration. This handheld device produces one liter of medical-grade water in 21 minutes. Total production capacity for this innovation is expected to be in the hundreds of liters. The device contains one battery powered electric mini-pump. Alternatively, a manually powered pump can be attached and used. Drinking water enters the device from a source water bag, flows through two filters, and final sterile production water exits into a sealed, medical-grade collection bag. The collection bag contains pre-placed crystalline salts to mix with product water to form isotonic intravenous medical solutions. Alternatively, a hypertonic salt solution can be injected into a filled bag. The filled collection bag is detached from the device and is ready for use or storage. This device currently contains one collection bag, but a manifold of several pre-attached bags or replacement of single collection bags under sterile needle technique is possible for the production of multiple liters. The entire system will be flushed, sealed, and radiation-sterilized. Operation of the device is easy and requires minimal training. Drinking water is placed into the collection bag. Inline stopcock flow valves at the source and collection bags are opened, and the mini-pump is turned on by a switch to begin fluid flow. When the collection bag is completely filled with the medical- grade water, the pump can be turned off. The pump is designed so it cannot pump air, and overfilling of the collection bag with fluid is avoided by placing an equal amount of water in the source bag. Backflow is avoided by inline check valves. The filled collection bag is disconnected from its tubing and is ready for use. The source bag can be refilled for production of multiple liters, or the source bag can be replaced with an input tube that can be placed in a larger potable water source if the device is attended. The device functions in all orientations independent of any gravity fields. In addition to creating IV fluids, the device produces medical-grade water, which can be used for mixing with medications for injection, reconstituting freeze-dried blood products for injection, or for wound hydration or irrigation. Potential worldwide use is expected with medical activities in environments that have limited resources, storage, or resupply such as in military field operations, humanitarian relief efforts, submarines, commercial cruise ships, etc.

SIMS prototype system 1 test results: Engineering analysis

NASA Technical Reports Server (NTRS)

1978-01-01

The space and domestic water solar heating system designated SIMS Prototype Systems 1 was evaluated. The test system used 720 ft (gross) of Solar Energy Products Air Collectors, a Solar Control Corporation SAM 20 Air Handler with Model 75-175 control unit, a Jackson Solar Storage tank with Rho Sigma Mod 106 controller, and 20 tons of rack storage. The test data analysis performed evaluates the system performance and documents the suitability of SIMS Prototype System 1 hardware for field installation.

Storage conditions for stability of offline measurement of fractional exhaled nitric oxide after collection for epidemiologic research

PubMed Central

2012-01-01

Background The measurement of fractional concentration of nitric oxide in exhaled air (FeNO) is valuable for the assessment of airway inflammation. Offline measurement of FeNO has been used in some epidemiologic studies. However, the time course of the changes in FeNO after collection has not been fully clarified. In this study, the effects of storage conditions on the stability of FeNO measurement in exhaled air after collection for epidemiologic research were examined. Methods Exhaled air samples were collected from 48 healthy adults (mean age 43.4 ± 12.1 years) in Mylar bags. FeNO levels in the bags were measured immediately after collection. The bags were then stored at 4°C or room temperature to measure FeNO levels repeatedly for up to 168 hours. Results In the bags stored at room temperature after collection, FeNO levels were stable for 9 hours, but increased starting at 24 hours. FeNO levels remained stable for a long time at 4°C, and they were 99.7% ± 7.7% and 101.3% ± 15.0% relative to the baseline values at 24 and 96 hours, respectively. When the samples were stored at 4°C, FeNO levels gradually decreased with time among the subjects with FeNO ≥ 51 ppb immediately after collection, although there were almost no changes among the other subjects. FeNO levels among current smokers increased even at 4°C, although the values among ex-smokers decreased gradually, and those among nonsmokers remained stable. The rate of increase was significantly higher among current smokers than among nonsmokers and ex-smokers from 9 hours after collection onwards. Conclusions Storage at 4°C could prolong the stability of FeNO levels after collection. This result suggests that valid measurements can be performed within several days if the samples are stored at 4°C. However, the time course of the changes in FeNO levels differed in relation to initial FeNO values and cigarette smoking. PMID:23116255

75 FR 57549 - Fisker Automotive; Grant of Application for Temporary Exemption From Advanced Air Bag...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-21

... electric motors that get their power from a rechargeable Lithium-ion battery, or, when that is depleted, by... Americans drive each day. The battery can be charged at home overnight. Using gas and electric power, Fisker...

Effect of municipal solid waste incinerator types on characteristics of ashes from different air pollution control devices.

PubMed

Lu, Chien-Hsing; Chuang, Kui-Hao

2016-01-01

The purpose of this paper is to investigate the characteristics of fly and bottom ashes sampled from both fluidized bed (FB) and mass-burning (MB) municipal solid waste incinerators (MSWIs), respectively. Fly ashes from different locations at FB and MB MSWIs equipped with a cyclone, a semi-dry scrubber, and a bag filter as air pollution control devices were examined to provide the baseline information between physicochemical properties and leaching ability. Experimental results of leachability indicated that the bag filter fly ash (FB-FA(B)) from the FB incinerator meets Taiwan regulatory standards set through the toxicity characteristic leaching procedure. X-ray diffraction results revealed the presence of Cr5O12 and Pb2O3 in the cyclone fly ash (MB-FA(C)) and bag filter fly ash (MB-FA(B)), respectively, from the MB incinerator. To observe lead incorporation mechanism, mixture of simulate lead-laden waste with bed material were fired between 600 °C and 900 °C in a laboratory scale FB reactor. The results clearly demonstrate a substantial decrease in lead leaching ratio for products with an appropriate temperature. The concentration of Pb in the MB-FA(B) was 250 times that in the FB-FA(B), suggesting that incineration of MSW in FB is a good strategy for stabilizing hazardous metals.

Real-time contaminant sensing and control in civil infrastructure systems

NASA Astrophysics Data System (ADS)

Rimer, Sara; Katopodes, Nikolaos

2014-11-01

A laboratory-scale prototype has been designed and implemented to test the feasibility of real-time contaminant sensing and control in civil infrastructure systems. A blower wind tunnel is the basis of the prototype design, with propylene glycol smoke as the ``contaminant.'' A camera sensor and compressed-air vacuum nozzle system is set up at the test section portion of the prototype to visually sense and then control the contaminant; a real-time controller is programmed to read in data from the camera sensor and administer pressure to regulators controlling the compressed air operating the vacuum nozzles. A computational fluid dynamics model is being integrated in with this prototype to inform the correct pressure to supply to the regulators in order to optimally control the contaminant's removal from the prototype. The performance of the prototype has been evaluated against the computational fluid dynamics model and is discussed in this presentation. Furthermore, the initial performance of the sensor-control system implemented in the test section of the prototype is discussed. NSF-CMMI 0856438.

Improved fireman's compressed air breathing system pressure vessel development program

NASA Technical Reports Server (NTRS)

King, H. A.; Morris, E. E.

1973-01-01

Prototype high pressure glass filament-wound, aluminum-lined pressurant vessels suitable for use in a fireman's compressed air breathing system were designed, fabricated, and acceptance tested in order to demonstrate the feasibility of producing such high performance, lightweight units. The 4000 psi tanks have a 60 standard cubic foot (SCF) air capacity, and have a 6.5 inch diamter, 19 inch length, 415 inch volume, weigh 13 pounds when empty, and contain 33 percent more air than the current 45 SCF (2250 psi) steel units. The current steel 60 SCF (3000 psi) tanks weigh approximately twice as much as the prototype when empty, and are 2 inches, or 10 percent shorter. The prototype units also have non-rusting aluminum interiors, which removes the hazard of corrosion, the need for internal coatings, and the possibility of rust particles clogging the breathing system.

Cost-effective retrofit technology for reducing peak power demand in small and medium commercial buildings

DOE PAGES

Nutaro, James J.; Fugate, David L.; Kuruganti, Teja; ...

2015-05-27

We describe a cost-effective retrofit technology that uses collective control of multiple rooftop air conditioning units to reduce the peak power consumption of small and medium commercial buildings. The proposed control uses a model of the building and air conditioning units to select an operating schedule for the air conditioning units that maintains a temperature set point subject to a constraint on the number of units that may operate simultaneously. A prototype of this new control system was built and deployed in a large gymnasium to coordinate four rooftop air conditioning units. Based on data collected while operating this prototype,more » we estimate that the cost savings achieved by reducing peak power consumption is sufficient to repay the cost of the prototype within a year.« less

The exposure of children to deploying side air bags: an initial field assessment.

PubMed

Arbogast, Kristy B; Kallan, Michael J

2007-01-01

Tremendous effort has been invested in the laboratory to ensure side air bag (SAB) deployments minimize injury metrics in pediatric anthropometric test devices (ATDs). Little is known, however, about the experience of children exposed to this technology in real world crashes. Therefore, the objective of this study was to determine the prevalence of SAB exposure in children and provide estimates of injury risk among those exposed. This study utilized data from the Partners for Child Passenger Safety study, a large-scale child-focused crash surveillance system, to identify a probability sample of 348 child occupants, age 0-15 years, weighted to represent 6,600 children, in vehicles of model year 1998 and newer, equipped with SABs, in side impact crashes from three large U.S. regions between 1/1/05 and 12/31/06. In the study sample, 27 children per 1000 children in crashes were exposed to a deployed side air bag. Over 75% of these children were seated in the rear seat and 83% were exposed to a head curtain SAB. 65% of those exposed were less than 9 years of age. Of those exposed, 10.6% sustained an AIS2+ injury; all injuries were of the AIS 2 level and limited to the head or upper extremity. This paper provides the first population-based estimates of the exposure of children to SABs. Initial experience suggests that the risk of injury is fairly low with only one in ten sustaining injury - none of which were serious or life threatening. These findings offer assurance that efforts by regulators and the automotive industry to minimize negative consequences from SABs to vulnerable occupants appear to be effective and cause no change in the current recommendation of safe seating for children next to SABs.

An Experimental Study of Unconfined Hydrogen/Oxygen and Hydrogen/Air Explosions

NASA Technical Reports Server (NTRS)

Richardson, Erin; Skinner, Troy; Blackwood, James; Hays, Michael; Bangham, Mike; Jackson, Austin

2014-01-01

Development tests are being conducted to characterize unconfined Hydrogen/air and Hydrogen/Oxygen blast characteristics. Most of the existing experiments for these types of explosions address contained explosions, like shock tubes. Therefore, the Hydrogen Unconfined Combustion Test Apparatus (HUCTA) has been developed as a gaseous combustion test device for determining the relationship between overpressure, impulse, and flame speed at various mixture ratios for unconfined reactions of hydrogen/oxygen and hydrogen/air. The system consists of a central platform plumbed to inject and mix component gasses into an attached translucent bag or balloon while monitoring hydrogen concentration. All tests are ignited with a spark with plans to introduce higher energy ignition sources in the future. Surrounding the platform are 9 blast pressure "Pencil" probes. Two high-speed cameras are used to observe flame speed within the combustion zone. The entire system is raised approx. 6 feet off the ground to remove any ground reflection from the measurements. As of this writing greater than 175 tests have been performed and include Design of Experiments test sets. Many of these early tests have used bags or balloons between approx. 340L and approx. 1850L to quantify the effect of gaseous mixture ratio on the properties of interest. All data acquisition is synchronized between the high-speed cameras, the probes, and the ignition system to observe flame and shock propagation. Successful attempts have been made to couple the pressure profile with the progress of the flame front within the combustion zone by placing a probe within the bag. Overpressure and impulse data obtained from these tests are used to anchor engineering analysis tools, CFD models and in the development of blast and fragment acceleration models.

Microbial Contents of Vacuum Cleaner Bag Dust and Emitted Bioaerosols and Their Implications for Human Exposure Indoors

PubMed Central

Veillette, Marc; Knibbs, Luke D.; Pelletier, Ariane; Charlebois, Remi; Blais Lecours, Pascale; He, Congrong; Morawska, Lidia

2013-01-01

Vacuum cleaners can release large concentrations of particles, both in their exhaust air and from resuspension of settled dust. However, the size, variability, and microbial diversity of these emissions are unknown, despite evidence to suggest they may contribute to allergic responses and infection transmission indoors. This study aimed to evaluate bioaerosol emission from various vacuum cleaners. We sampled the air in an experimental flow tunnel where vacuum cleaners were run, and their airborne emissions were sampled with closed-face cassettes. Dust samples were also collected from the dust bag. Total bacteria, total archaea, Penicillium/Aspergillus, and total Clostridium cluster 1 were quantified with specific quantitative PCR protocols, and emission rates were calculated. Clostridium botulinum and antibiotic resistance genes were detected in each sample using endpoint PCR. Bacterial diversity was also analyzed using denaturing gradient gel electrophoresis (DGGE), image analysis, and band sequencing. We demonstrated that emission of bacteria and molds (Penicillium/Aspergillus) can reach values as high as 1E5 cell equivalents/min and that those emissions are not related to each other. The bag dust bacterial and mold content was also consistent across the vacuums we assessed, reaching up to 1E7 bacterial or mold cell equivalents/g. Antibiotic resistance genes were detected in several samples. No archaea or C. botulinum was detected in any air samples. Diversity analyses showed that most bacteria are from human sources, in keeping with other recent results. These results highlight the potential capability of vacuum cleaners to disseminate appreciable quantities of molds and human-associated bacteria indoors and their role as a source of exposure to bioaerosols. PMID:23934489

Advances in the Lightweight Air-Liquid Composite Heat Exchanger Development for Space Exploration Applications

NASA Technical Reports Server (NTRS)

Shin, E. Eugene; Johnston, J. Chris; Haas, Daniel

2011-01-01

An advanced, lightweight composite modular Air/Liquid (A/L) Heat Exchanger (HX) Prototype for potential space exploration thermal management applications was successfully designed, manufactured, and tested. This full-scale Prototype consisting of 19 modules, based on recommendations from its predecessor Engineering Development unit (EDU) but with improved thermal characteristics and manufacturability, was 11.2 % lighter than the EDU and achieves potentially a 42.7% weight reduction from the existing state-of-the-art metallic HX demonstrator. However, its higher pressure drop (0.58 psid vs. 0.16 psid of the metal HX) has to be mitigated by foam material optimizations and design modifications including a more systematic air channel design. Scalability of the Prototype design was validated experimentally by comparing manufacturability and performance between the 2-module coupon and the 19-module Prototype. The Prototype utilized the thermally conductive open-cell carbon foam material but with lower density and adopted a novel high-efficiency cooling system with significantly increased heat transfer contact surface areas, improved fabricability and manufacturability compared to the EDU. Even though the Prototype was required to meet both the thermal and the structural specifications, accomplishing the thermal requirement was a higher priority goal for this first version. Overall, the Prototype outperformed both the EDU and the corresponding metal HX, particularly in terms of specific heat transfer, but achieved 93.4% of the target. The next generation Prototype to achieve the specification target, 3,450W would need 24 core modules based on the simple scaling factor. The scale-up Prototype will weigh about 14.7 Kg vs. 21.6 Kg for the metal counterpart. The advancement of this lightweight composite HX development from the original feasibility test coupons to EDU to Prototype is discussed in this paper.

Development of a Universal Waste Management System

NASA Technical Reports Server (NTRS)

Baccus, Shelley; Broyan, James L., Jr.

2013-01-01

A concept for a Universal Waste Management System (UWMS) has been developed based on the knowledge gained from over 50 years of space travel. It is being designed for Commercial Orbital Transportation Services (COTS) and Multi ]Purpose Crew Vehicle (MPCV) and is based upon the Extended Duration Orbiter (EDO) commode. The UMWS was modified to enhance crew interface and reduce volume and cost. The UWMS will stow waste in fecal canisters, similar to the EDO, and urine will be stowed in bags for in orbit change out. This allows the pretreated urine to be subsequently processed and recovered as drinking water. The new design combines two fans and a rotary phase separator on a common shaft to allow operation by a single motor. This change enhances packaging by reducing the volume associated with an extra motor, associated controller, harness, and supporting structure. The separator pumps urine to either a dual bag design for COTS vehicles or directly into a water reclamation system. The commode is supported by a concentric frame, enhancing its structural integrity while further reducing the volume from the previous design. The UWMS flight concept development effort is underway and an early output of the development will be a ground based UMWS prototype for manned testing. Referred to as the Gen 3 unit, this prototype will emulate the crew interface included in the UWMS and will offer a great deal of knowledge regarding the usability of the new design, allowing the design team the opportunity to modify the UWMS flight concept based on the manned testing.

Supplement : development of improved injury criteria for the assessment of advanced automotive restraint systems : II

DOT National Transportation Integrated Search

2000-03-01

In the Supplemental Notice of Proposed Rulemaking (SNPRM) on advanced air bags, the National Highway Traffic Safety Administration (NHTSA) proposed a comprehensive set of injury criteria for evaluating the potential for injury to the head, neck, ches...

Analytical instrument with apparatus and method for sample concentrating

DOEpatents

Zaromb, S.

1986-08-04

A system for analysis of trace concentrations of contaminants in air includes a portable liquid chromatograph and a preconcentrator for the contaminants to be analyzed. The preconcentrator includes a sample bag having an inlet valve and an outlet valve for collecting an air sample. When the sample is collected the sample bag is connected in series with a sorbing apparatus in a recirculation loop. The sorbing apparatus has an inner gas-permeable container containing a sorbent material and an outer gas-impermeable container. The sample is circulated through the outer container and around the inner container for trapping and preconcentrating the contaminants in the sorbent material. The sorbent material may be a liquid having the same composition as the mobile phase of the chromatograph for direct injection thereinto. Alternatively, the sorbent material may be a porous, solid body, to which mobile phase liquid is added after preconcentration of the contaminants for dissolving the contaminants, the liquid solution then being withdrawn for injection into the chromatograph.

Rethinking Airbag Safety: Airbag Injury Causing Bilateral Blindness

PubMed Central

Ogun, Olufunmilola Abimbola; Ikyaa, Sewuese Yangi; Ogun, Gabriel Olabiyi

2014-01-01

A healthy 40-year-old man, restrained in the front passenger seat, suffered visually disabling blunt ocular trauma following spontaneous release of the passenger side air-bag module, during vehicular deceleration, without an automobile crash. Though the driver-side airbag was also released, the driver was unharmed. The passenger suffered bilateral hyphema, bilateral vitreous hemorrhage and suspected posterior scleral rupture in the left eye and also had an eyebrow laceration, from impact with the dashboard panel covering the air-bag module, which was detached by the force of airbag deployment. This is the first reported case from West Africa and the first case in which part of the airbag module detached to cause additional trauma. This report adds to the growing burden of evidence world-wide, for a review of the safety aspects of the automobile airbag. This case clearly illustrates that although airbags reduce mortality, they carry a high risk of ocular morbidity, even with seat belt restraint. PMID:24791116

Analytical instrument with apparatus for sample concentrating

DOEpatents

Zaromb, Solomon

1989-01-01

A system for analysis of trace concentrations of contaminants in air includes a portable liquid chromatograph and a preconcentrator for the contaminants to be analyzed. The preconcentrator includes a sample bag having an inlet valve and an outlet valve for collecting an air sample. When the sample is collected the sample bag is connected in series with a sorbing apparatus in a recirculation loop. The sorbing apparatus has an inner gas-permeable container containing a sorbent material and an outer gas-impermeable container. The sample is circulated through the outer container and around the inner container for trapping and preconcentrating the contaminants in the sorbent material. The sorbent material may be a liquid having the same composition as the mobile phase of the chromatograph for direct injection thereinto. Alternatively, the sorbent material may be a porous, solid body, to which mobile phase liquid is added after preconcentration of the contaminants for dissolving the contaminants, the liquid solution then being withdrawn for injection into the chromatograph.

Method for preconcentrating a sample for subsequent analysis

DOEpatents

Zaromb, Solomon

1990-01-01

A system for analysis of trace concentration of contaminants in air includes a portable liquid chromatograph and a preconcentrator for the contaminants to be analyzed. The preconcentrator includes a sample bag having an inlet valve and an outlet valve for collecting an air sample. When the sample is collected the sample bag is connected in series with a sorbing apparatus in a recirculation loop. The sorbing apparatus has an inner gas-permeable container containing a sorbent material and an outer gas-impermeable container. The sample is circulated through the outer container and around the inner container for trapping and preconcentrating the contaminants in the sorbent material. The sorbent material may be a liquid having the same composition as the mobile phase of the chromatograph for direct injection thereinto. Alternatively, the sorbent material may be a porous, solid body, to which mobile phase liquid is added after preconcentration of the contaminants for dissolving the contaminants, the liquid solution then being withdrawn for injection into the chromatograph.

Monitoring of heavy metal concentrations in home outdoor air using moss bags.

PubMed

Rivera, Marcela; Zechmeister, Harald; Medina-Ramón, Mercedes; Basagaña, Xavier; Foraster, Maria; Bouso, Laura; Moreno, Teresa; Solanas, Pascual; Ramos, Rafael; Köllensperger, Gunda; Deltell, Alexandre; Vizcaya, David; Künzli, Nino

2011-04-01

One monitoring station is insufficient to characterize the high spatial variation of traffic-related heavy metals within cities. We tested moss bags (Hylocomium splendens), deployed in a dense network, for the monitoring of metals in outdoor air and characterized metals' long-term spatial distribution and its determinants in Girona, Spain. Mosses were exposed outside 23 homes for two months; NO₂ was monitored for comparison. Metals were not highly correlated with NO₂ and showed higher spatial variation than NO₂. Regression models explained 61-85% of Cu, Cr, Mo, Pb, Sb, Sn, and Zn and 72% of NO₂ variability. Metals were strongly associated with the number of bus lines in the nearest street. Heavy metals are an alternative traffic-marker to NO₂ given their toxicological relevance, stronger association with local traffic and higher spatial variability. Monitoring heavy metals with mosses is appealing, particularly for long-term exposure assessment, as mosses can remain on site many months without maintenance. Copyright © 2010 Elsevier Ltd. All rights reserved.

Comparison of devices for newborn ventilation in the delivery room.

PubMed

Szyld, Edgardo; Aguilar, Adriana; Musante, Gabriel A; Vain, Nestor; Prudent, Luis; Fabres, Jorge; Carlo, Waldemar A

2014-08-01

To evaluate the effectiveness and safety of a T-piece resuscitator compared with a self-inflating bag for providing mask ventilation to newborns at birth. Newborns at ≥26 weeks gestational age receiving positive-pressure ventilation at birth were included in this multicenter cluster-randomized 2-period crossover trial. Positive-pressure ventilation was provided with either a self-inflating bag (self-inflating bag group) with or without a positive end-expiratory pressure valve or a T-piece with a positive end-expiratory pressure valve (T-piece group). Delivery room management followed American Academy of Pediatrics and International Liaison Committee on Resuscitation guidelines. The primary outcome was the proportion of newborns with heart rate (HR)≥100 bpm at 2 minutes after birth. A total of 1027 newborns were included. There was no statistically significant difference in the incidence of HR≥100 bpm at 2 minutes after birth between the T-piece and self-inflating bag groups: 94% (479 of 511) and 90% (466 of 516), respectively (OR, 0.65; 95% CI, 0.41-1.05; P=.08). A total of 86 newborns (17%) in the T-piece group and 134 newborns (26%) in the self-inflating bag group were intubated in the delivery room (OR, 0.58; 95% CI, 0.4-0.8; P=.002). The mean±SD maximum positive inspiratory pressure was 26±2 cm H2O in the T-piece group vs 28±5 cm H2O in the self-inflating bag group (P<.001). Air leaks, use of drugs/chest compressions, mortality, and days on mechanical ventilation did not differ significantly between groups. There was no difference between the T-piece resuscitator and a self-inflating bag in achieving an HR of ≥100 bpm at 2 minutes in newborns≥26 weeks gestational age resuscitated at birth. However, use of the T-piece decreased the intubation rate and the maximum pressures applied. Copyright © 2014 Elsevier Inc. All rights reserved.

Automatic Sprout Grower

NASA Technical Reports Server (NTRS)

Sauer, Richard L.; Scheld, H. W.; Magnuson, J. W.

1989-01-01

Self-contained seed-sprouting system provides environment for sprouting seeds quickly and easily. Sprouting container standard 6-oz package for dehydrated food and drink mixes in Space Shuttle. About 4 g of dry alfalfa or radish seeds vacuum-sealed in each cup, like freeze-dried foods. Sixteen cups suspended in tray. Air-and-water inlet tube links each cup to system of tubes and solenoid valves alternately furnish air and water and remove stale air. Peristaltic pump supplies water from vinyl medical-fluid bag. Small diaphragm pump supplies and exhausts air. Small circuit board times movements of air and water. Kit offers advantages to home gardeners. Apartment dwellers use it for steady production of homegrown sprouts even though they have no garden space.

Equivalent Air Spring Suspension Model for Quarter-Passive Model of Passenger Vehicles.

PubMed

Abid, Haider J; Chen, Jie; Nassar, Ameen A

2015-01-01

This paper investigates the GENSIS air spring suspension system equivalence to a passive suspension system. The SIMULINK simulation together with the OptiY optimization is used to obtain the air spring suspension model equivalent to passive suspension system, where the car body response difference from both systems with the same road profile inputs is used as the objective function for optimization (OptiY program). The parameters of air spring system such as initial pressure, volume of bag, length of surge pipe, diameter of surge pipe, and volume of reservoir are obtained from optimization. The simulation results show that the air spring suspension equivalent system can produce responses very close to the passive suspension system.

Forensic Application of Microbiological Culture Analysis To Identify Mail Intentionally Contaminated with Bacillus anthracis Spores†

PubMed Central

Beecher, Douglas J.

2006-01-01

The discovery of a letter intentionally filled with dried Bacillus anthracis spores in the office of a United States senator prompted the collection and quarantine of all mail in congressional buildings. This mail was subsequently searched for additional intentionally contaminated letters. A microbiological sampling strategy was used to locate heavy contamination within the 642 separate plastic bags containing the mail. Swab sampling identified 20 bags for manual and visual examination. Air sampling within the 20 bags indicated that one bag was orders of magnitude more contaminated than all the others. This bag contained a letter addressed to Senator Patrick Leahy that had been loaded with dried B. anthracis spores. Microbiological sampling of compartmentalized batches of mail proved to be efficient and relatively safe. Efficiency was increased by inoculating culture media in the hot zone rather than transferring swab samples to a laboratory for inoculation. All mail sampling was complete within 4 days with minimal contamination of the sampling environment or personnel. However, physically handling the intentionally contaminated letter proved to be exceptionally hazardous, as did sorting of cross-contaminated mail, which resulted in generation of hazardous aerosol and extensive contamination of protective clothing. Nearly 8 × 106 CFU was removed from the most highly cross-contaminated piece of mail found. Tracking data indicated that this and other heavily contaminated envelopes had been processed through the same mail sorting equipment as, and within 1 s of, two intentionally contaminated letters. PMID:16885280

Development of visibility forecasting modeling framework for the Lower Fraser Valley of British Columbia using Canada's Regional Air Quality Deterministic Prediction System.

PubMed

So, Rita; Teakles, Andrew; Baik, Jonathan; Vingarzan, Roxanne; Jones, Keith

2018-05-01

Visibility degradation, one of the most noticeable indicators of poor air quality, can occur despite relatively low levels of particulate matter when the risk to human health is low. The availability of timely and reliable visibility forecasts can provide a more comprehensive understanding of the anticipated air quality conditions to better inform local jurisdictions and the public. This paper describes the development of a visibility forecasting modeling framework, which leverages the existing air quality and meteorological forecasts from Canada's operational Regional Air Quality Deterministic Prediction System (RAQDPS) for the Lower Fraser Valley of British Columbia. A baseline model (GM-IMPROVE) was constructed using the revised IMPROVE algorithm based on unprocessed forecasts from the RAQDPS. Three additional prototypes (UMOS-HYB, GM-MLR, GM-RF) were also developed and assessed for forecast performance of up to 48 hr lead time during various air quality and meteorological conditions. Forecast performance was assessed by examining their ability to provide both numerical and categorical forecasts in the form of 1-hr total extinction and Visual Air Quality Ratings (VAQR), respectively. While GM-IMPROVE generally overestimated extinction more than twofold, it had skill in forecasting the relative species contribution to visibility impairment, including ammonium sulfate and ammonium nitrate. Both statistical prototypes, GM-MLR and GM-RF, performed well in forecasting 1-hr extinction during daylight hours, with correlation coefficients (R) ranging from 0.59 to 0.77. UMOS-HYB, a prototype based on postprocessed air quality forecasts without additional statistical modeling, provided reasonable forecasts during most daylight hours. In terms of categorical forecasts, the best prototype was approximately 75 to 87% correct, when forecasting for a condensed three-category VAQR. A case study, focusing on a poor visual air quality yet low Air Quality Health Index episode, illustrated that the statistical prototypes were able to provide timely and skillful visibility forecasts with lead time up to 48 hr. This study describes the development of a visibility forecasting modeling framework, which leverages the existing air quality and meteorological forecasts from Canada's operational Regional Air Quality Deterministic Prediction System. The main applications include tourism and recreation planning, input into air quality management programs, and educational outreach. Visibility forecasts, when supplemented with the existing air quality and health based forecasts, can assist jurisdictions to anticipate the visual air quality impacts as perceived by the public, which can potentially assist in formulating the appropriate air quality bulletins and recommendations.

Indoor Air Nuclear, Biological, and Chemical Health Modeling and Assessment System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stenner, Robert D.; Hadley, Donald L.; Armstrong, Peter R.

2001-03-01

Indoor air quality effects on human health are of increasing concern to public health agencies and building owners. The prevention and treatment of 'sick building' syndrome and the spread of air-borne diseases in hospitals, for example, are well known priorities. However, increasing attention is being directed to the vulnerability of our public buildings/places, public security and national defense facilities to terrorist attack or the accidental release of air-borne biological pathogens, harmful chemicals, or radioactive contaminants. The Indoor Air Nuclear, Biological, and Chemical Health Modeling and Assessment System (IA-NBC-HMAS) was developed to serve as a health impact analysis tool for usemore » in addressing these concerns. The overall goal was to develop a user-friendly fully functional prototype Health Modeling and Assessment system, which will operate under the PNNL FRAMES system for ease of use and to maximize its integration with other modeling and assessment capabilities accessible within the FRAMES system (e.g., ambient air fate and transport models, water borne fate and transport models, Physiologically Based Pharmacokinetic models, etc.). The prototype IA-NBC-HMAS is designed to serve as a functional Health Modeling and Assessment system that can be easily tailored to meet specific building analysis needs of a customer. The prototype system was developed and tested using an actual building (i.e., the Churchville Building located at the Aberdeen Proving Ground) and release scenario (i.e., the release and measurement of tracer materials within the building) to ensure realism and practicality in the design and development of the prototype system. A user-friendly "demo" accompanies this report to allow the reader the opportunity for a "hands on" review of the prototype system's capability.« less

Comparison of face masks in the bag-mask ventilation of a manikin.

PubMed

Redfern, D; Rassam, S; Stacey, M R; Mecklenburgh, J S

2006-02-01

We conducted a study investigating the effectiveness of four face mask designs in the bag-mask ventilation of a special manikin adapted to simulate a difficult airway. Forty-eight anaesthetists volunteered to bag-mask ventilate the manikin for 3 min with four different face masks. The primary outcome of the study was to calculate mean percentage leak from the face masks over 3 min. Anaesthetists were also asked to rate the face masks using a visual analogue score. The single-use scented intersurgical face mask had the lowest mean leak (20%). This was significantly lower than the mean leak from the single-use, cushioned 7,000 series Air Safety Ltd. face mask (24%) and the reusable silicone Laerdal face mask (27%) but not significantly lower than the mean leak from the reusable anatomical intersurgical face mask (23%). There was a large variation in both performance and satisfaction between anaesthetists with each design. This highlights the importance of having a variety of face masks available for emergency use.

Biomonitoring of heavy metals contamination by mosses and lichens around Slovinky tailing pond (Slovakia).

PubMed

Demková, Lenka; Bobul'ská, Lenka; Árvay, Július; Jezný, Tomáš; Ducsay, Ladislav

2017-01-02

Three moss (Pleurozium spp., Polytrichum spp., and Rhytidiadelphus spp.) and two lichen (Hypogymnia physodes and Pseudevernia furfuracea) taxons covered in the bags were used to monitor air quality. Bags were exposed at the different distances from the tailing pond because of insufficient security and source of heavy metal pollution. Moss/lichen bags were exposed for six weeks at 0-, 50-, 100-, 150- and 200-m distances from Slovinky tailing pond, in the main wind direction (down the valley). Accumulation ability of heavy metals expressed by relative accumulation factor (RAF) increases in the order of Polytrichum spp.

[Appropriate dust control measures for jade carving operations].

PubMed

Liu, Jiang; Wang, Qiushui; Liu, Guangquan

2002-12-01

To provide the appropriate dust control measures for jade carving operations. Dust concentrations in the workplace were measured according to GB/T 5748-85. Ventilation system of dust control were measured according to GB/T 16157-1996. Dust particle size distributions for different sources and particle size fraction collecting efficiencies of the dust collectors were measured with WY-1 in-stack 7 stage cascade impactors. On the basis of adopting wet process in the carving operations, local exhaust ventilation system for dust control was installed, which included: the special designed slot exhaust hoods with hood face velocity of 2.5 m/s and exhaust volume of 600 m3/h. The pipe sizes were determined according to the air volume passing through the pipe and the reasonable air velocities. Impinging scrubber or bag filter dust collector were selected to treat the dust laden air from the local exhaust ventilation system, which gave a total collecting efficiency of 97% for impinging scrubber and 98% for bag filter; The type of fan and its size were selected according to the total air volume of the ventilation system and maximum total pressure needed for the longest pipe line plus the pressure drop of the dust collector. Practical application showed that, after installation and use of the appropriate dust control measures, the dust concentrations in the workplaces could meet or nearly meet the national hygienic standard and the dust laden air at the local exhaust ventilation system could meet the national emission standard.

Low Velocity Airdrop Tests of an X-38 Backup Parachute Design

NASA Technical Reports Server (NTRS)

Stein, Jenny M.; Machin, Ricardo A.; Wolf, Dean F.; Hillebrandt, F. David

2007-01-01

The NASA Johnson Space Center's X-38 program designed a new backup parachute system to recover the 25,000 lb X-38 prototype for the Crew Return Vehicle spacecraft. Due to weight and cost constraints, the main backup parachute design incorporated rapid and low cost fabrication techniques using off-the-shelf materials. Near the vent, the canopy was constructed of continuous ribbons, to provide more damage tolerance. The remainder of the canopy was a constructed with a continuous ringslot design. After cancellation of the X-38 program, the parachute design was resized, built, and drop tested for Natick Soldiers Center's Low Velocity Air Drop (LVAD) program to deliver cargo loads up to 22,000 lbs from altitudes as low as 500 feet above the ground. Drop tests results showed that the 500-foot LVAD parachute deployment conditions cause severe skirt inversion and inflation problems for large parachutes. The bag strip occurred at a high angle of attack, causing skirt inversion before the parachute could inflate. The addition of a short reefing line prevented the skirt inversion. Using a lower porosity in the vent area, than is normally used in large parachutes, improved inflation. The drop testing demonstrated that the parachute design could be refined to meet the requirements for the 500-foot LVAD mission.

General Walton H. Walker: A Talent for Training

DTIC Science & Technology

2011-05-19

history that enriched my understanding and appreciation of our profession. Dr. Wilson Heefner’s graciousness and kind words enabled me to conduct a more in...Support Command provided invaluable air-ground integration training by bombing tanks with flour bags and providing realistic strafing runs on troops

Summary of new test dummies, injury criteria

DOT National Transportation Integrated Search

2000-06-17

Besides a plethora of new tests, the air bag standard issued recently calls for four new test dummies in addition to the average size adult male already used in testing: small adult female; 6 year old child; 3 year old child; and 1 year old infant. I...

77 FR 29247 - Federal Motor Vehicle Safety Standards; Occupant Crash Protection

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-17

...). ACTION: Final rule; technical amendments. SUMMARY: This final rule makes technical amendments to Federal... advanced air bag requirements. As written now, the general warning label requirements contain an explicit... equipment requirements for restraint systems. This document makes technical amendments to several of the...

KSC-03pd0389

NASA Image and Video Library

2003-02-13

KENNEDY SPACE CENTER, FLA. -- The reconstruction team record and bag some of the Columbia debris inside the RLV Hangar. The debris was shipped from Barksdale Air Force Base, Shreveport, La. As part of the ongoing investigation into the tragic accident, workers will attempt to reconstruct the orbiter inside the RLV.

40 CFR 1066.601 - Overview.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Overview. 1066.601 Section 1066.601 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS VEHICLE-TESTING..., such as multiple weighing of a PM filter or multiple readings from a bag sample. You may not use test...

40 CFR 1066.601 - Overview.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Overview. 1066.601 Section 1066.601 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS VEHICLE-TESTING..., such as multiple weighing of a PM filter or multiple readings from a bag sample. You may not use test...

KSC-2009-1378

NASA Image and Video Library

2008-11-07

VANDENBERG AIR FORCE BASE, Calif. – In the NASA payload processing facility at Vandenberg Air Force Base in California, the NOAA-N Prime satellite is bagged before moving it. NOAA-N Prime is the latest polar-orbiting operational environmental weather satellite developed by NASA for the National Oceanic and Atmospheric Administration. It is built by Lockheed Martin and similar to NOAA-N launched on May 20, 2005. Launch of NOAA-N Prime is scheduled for Feb. 4. Photo credit: NASA/Robert Hargreaves Jr., VAFB

Characterization of Air Emissions from Open Burning and ...

EPA Pesticide Factsheets

Emissions from open burning (OB) and open detonation (OD) of military ordnance and static fires (SF) of rocket motors were sampled in fall, 2013 at the Dundurn Depot (Saskatchewan, Canada). Emission sampling was conducted with an aerostat-lofted instrument package termed the “Flyer” that was maneuvered into the downwind plumes. Forty-nine OB events, 94 OD events, and 16 SF on four propellants types (Triple base, 105 M1, 155 M4A2 white bag, and 155 M6 red bag), two smokes (HC grenade and red phosphorus), five explosive types (Trigran, C4, ANFO, ANFO+HC grenade, and ANFO+Flare), and two rocket motors types (CVR-7 and MK 58) resulted in emission factors for particulate matter (PM), carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), volatile organic compounds (VOCs), chlorine species (HCl, chloride, chlorate, perchlorate), polychlorinated dibenzodioxins and polychlorinated dibenzofurans (PCDDs/PCDFs) and PM-based metals. These data provide Canada and the United States with additional air emissions data to support health risk assessments and permitting for safe treatment of military ordnance by OB/OD/SF. In addition, the data will be used to conduct air dispersion modelling assessing the impact of treatment of various ordnance on the air quality, to support mandatory reporting requirements of the Canadian Environmental Protection Act (CEPA), the National Pollutant Release Inventory (NPRI), and to update the Canadian Ammunition Chemical Database.Result

Flowrate testing of the bag filter LANCS-BOP 6CPVC-1.5-2SPVC (LANCS Industries) at 1 psig

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, Murray E.; Currie, Karissa Lyn; Berg, Charlotte Katherine

2016-09-13

The air flowrate through a flexible HEPA grade filter (Part LANCS-BOP 6CPVC-1.5-2SPVC www.lancsindustries.com) was measured at 48 ALPM for a differential pressure drop of 1.0 psig (28 inWC, 7.0 kPa). These filters are rated by the manufacturer to have a flowrate of 3 ALPM at a differential pressure drop of 1 inWC (0.25 kPa). The Los Alamos National Laboratory Aerosol Engineering Facility used one of their test rigs (originally developed to measure the pressure drop in capsule HEPA filters) to measure the airflow through the LANCS bag filter.

Exploration of PM2.5 filtration property of filter bag for environment protection

NASA Astrophysics Data System (ADS)

Zhu, Ruitian; Zheng, Jinwei; Ni, Bingxuan; Zhang, Peng

2017-06-01

In this paper, filter bag of polyphenylene sulfide (PPS) needle punched nonwoven for environment protection was investigated. The results showed that air permeability of sample was linear rise with the increase of the pressure drop. During the testing process, the residual pressure drop rose with the increase of cycles because of test dust attaching on the surface of the filter. The PM2.5 filtration efficiency was obtained of 99.854%, which was smaller than the dust filtration efficiency of 99.971% because of the fine particles taking larger proportion of the dust through the sample. Results show that this method of evaluating the PM2.5 filtration property is feasible.

Post-operative blood loss monitoring device: a new tool for nursing activities.

PubMed

Logier, R; Carette, D; Sozanski, J P; Jeanne, M; Jounwaz, R; De Jonckheere, J

2012-01-01

In most medical specialties, after surgery, it is usual to place a drain at the operative site level, in order to assist the blood flow-out if necessary. This drainage allows avoiding the formation of hematomas and contributes to tissues recovery. However, postoperative blood loss can lead to serious consequences. Also, it is necessary to continuously check the blood output volume in order to be able to intervene quickly in case of too significant losses. In daily clinical practice, this task is due to the nursing staff that periodically records the blood level inside the supple bag connected to the drain. However, this method is not accurate about the volume of lost blood and does not reflect the flow of losses which is an important parameter regarding the evolution of the patient setting. We have designed and developed a prototype of a blood loss monitoring device based on the continuous weight measurement of the blood bag connected to the drain. This device is fixed on the bed and is able to instantaneously alert the medical staff in case of abnormal blood flow-out.

ECLSS ARS humidifier separator repair onboard Atlantis, OV-104, during STS-44

NASA Technical Reports Server (NTRS)

1991-01-01

During STS-44, the Environmental Control and Life Support System (ECLSS) Air Revitalization System (ARS) humidifier separator is repaired using a towel and a plastic bag underneath the middeck subfloor of Atlantis, Orbiter Vehicle (OV) 104. Problems with the humidifier separator began about midway through the mission.

76 FR 51120 - Denial of Motor Vehicle Defect Petition

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-17

... crashes an air bag should have deployed, which were not always well-founded, or based on any technical analysis. There were 5 reports of non-deployment in a population of 176,471 \\4\\ Chevrolet Cobalt vehicles... NHTSA's Fatality Analysis Reporting System (FARS) tracks all fatal crashes involving motor vehicles in...

The use of air bags for mitigating grade crossing and trespass accidents : literature review and research plan.

DOT National Transportation Integrated Search

2016-06-01

This literature review will confirm prior work in the use of locomotive airbag technologies for vehicle or pedestrian collision : mitigation, and to focus planned activities and tasks for this research. The state of the art in relevant technologies h...

Examination of Air Force Crash Damaged or Disabled Aircraft Recovery Program Resourcing

DTIC Science & Technology

2011-06-01

Positioning for Lift ................................................................................... 2 Figure 4. 26 and 15-Ton Airbags Under Wing...15 Figure 5. Manufacture Depiction of Airbag System...lifting capacities are calculated at an airbag working pressure of seven pounds per square inch. The lifting bag example below is from AGE

40 CFR 63.7330 - What are my monitoring requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... relative change in particulate matter loadings using a bag leak detection system according to the... integrity of the baghouse through quarterly visual inspections of the baghouse interior for air leaks; and... must at all times monitor the pressure drop and water flow rate using a CPMS according to the...

Cost, weight and lead time impacts of a Mercedes-Benz 'Sensormat' type occupant detection system

DOT National Transportation Integrated Search

1997-04-19

This summary report is based, in part, on the findings contained in Contract No. DTNH22-96-C-02063 entitled "Cost Analysis of the Mercedes-Benz Occupant Detection System for Air Bag Shut-Off" prepared by Ludtke and Associates of Washington, Michigan....

Working in a Vacuum

ERIC Educational Resources Information Center

Rathey, Allen

2005-01-01

In this article, the author discusses several myths about vacuum cleaners and offers tips on evaluating and purchasing this essential maintenance tool. These myths are: (1) Amps mean performance; (2) Everyone needs high-efficiency particulate air (HEPA): (3) Picking up a "bowling ball" shows cleaning power; (4) All vacuum bags are the same; (5)…

LOW-LEVEL DETERMINATION OF PERCHLORATE IN DRINKING WATER USING ION CHROMATOGRAPHY MASS SPECTROMETRY

EPA Science Inventory

Perchlorate is a drinking water contaminant originating from the dissolution of the salts of ammonium, potassium, magnesium, or sodium in water. It is used primarily as an oxidant in solid propellant for rockets, missiles, pyrotechnics, as a component in air bag inflators, and i...

DEVELOPMENT OF A BETTER METHOD TO IDENTIFY AND MEASURE PERCHLORATE IN DRINKING WATER

EPA Science Inventory

Perchlorate (ClO4 -) is an oxidant used primarily in solid propellant for rockets, missiles, pyrotechnics, as a component in air bag inflators, and in highway safety flares. Perchlorate tainted water has been found throughout the southwestern United States where its source has o...