The thermodynamic properties of oxygen and nitrogen. Part 1: Thermodynamic properties of nitrogen from 115 R to 3500 R with pressures to 150000 psia

NASA Technical Reports Server (NTRS)

Stewart, R. B.; Jacobsen, R. T.; Myers, A. F.

1972-01-01

An equation of state is presented for liquid and gaseous nitrogen for temperatures from 115 R to 3500 R and pressures to 150,000 psia. All of the pressure-density-temperature data available from the published literature have been reviewed, and appropriate corrections have been identified and applied to bring experimental temperatures into accord with the International Practical Temperature Scale of 1968. Comparisons of property values calculated from the equation of state to measured values are included to illustrate the accuracy of the equation in representing the data. The coefficients of the equation of state were determined by a weighted least squares fit to selected published data and, simultaneously, to constant volume data determined by corresponding states analysis from oxygen data, and to data which define the phase equilibrium criteria for the saturated liquid and saturated vapor. The methods of weighting the various data for simultaneous fitting are presented and discussed. The equation of state is estimated to be accurate to within 0.5 percent in the liquid region, to within 0.1 percent for supercritical isotherms up to 15,000 psia, and to within 0.3 percent from 15,000 to 150,000 psia.

Impact of Chromophoric dissolved organic matter on light absorption in lake water on the Tibetan Plateau, China

NASA Astrophysics Data System (ADS)

Nima, Ciren; Hamre, Børge; Frette, Øyvind; Erga, Svein Rune; Chen, Yi-Chun; Zhao, Lu; Sørensen, Kai; Norli, Marit; Stamnes, Jakob J.

2017-02-01

Ground-based measurements of optical properties are rare for water in lakes on the Tibetan Plateau (TP). We analyzed the spectral absorption of Chromophoric Dissolved Organic Matter (CDOM) for water samples from Lake Namtso (LN) on the TP. The mean value of the spectral slope S280-500 for CDOM absorption was found to be 0.036 nm-1, whereas the corresponding mean value for S350-500 was found to be 0.015 nm-1, implying that when comparing spectral slope values with published values, the wavelength range used for deriving them should be considered.

Nuclear Data Sheets for A = 152

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, M.J.

2013-11-15

Detailed level schemes, decay schemes, and the experimental data on which they are based are presented for all nuclei with mass number A=152. The experimental data are evaluated; inconsistencies and discrepancies are noted; and adopted values for level and γ–ray energies, γ intensities, as well as for other nuclear properties are given. This evaluation replaces the A=152 evaluation published by Agda Artna–Cohen in Nuclear Data Sheets 79, 1 (1996) and the evaluation for 152Dy prepared by Balraj Singh and published in Nuclear Data Sheets 95, 995 (2002)

A method to investigate the diffusion properties of nuclear calcium.

PubMed

Queisser, Gillian; Wittum, Gabriel

2011-10-01

Modeling biophysical processes in general requires knowledge about underlying biological parameters. The quality of simulation results is strongly influenced by the accuracy of these parameters, hence the identification of parameter values that the model includes is a major part of simulating biophysical processes. In many cases, secondary data can be gathered by experimental setups, which are exploitable by mathematical inverse modeling techniques. Here we describe a method for parameter identification of diffusion properties of calcium in the nuclei of rat hippocampal neurons. The method is based on a Gauss-Newton method for solving a least-squares minimization problem and was formulated in such a way that it is ideally implementable in the simulation platform uG. Making use of independently published space- and time-dependent calcium imaging data, generated from laser-assisted calcium uncaging experiments, here we could identify the diffusion properties of nuclear calcium and were able to validate a previously published model that describes nuclear calcium dynamics as a diffusion process.

The NUBASE2016 evaluation of nuclear properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Audi, G.; Kondev, F. G.; Wang, Meng

This paper presents the NUBASE2016 evaluation that contains the recommended values for nuclear and decay properties of 3437 nuclides in their ground and excited isomeric (T1/2≥100 ns) states. All nuclides for which any experimental information is known were considered. NUBASE2016 covers all data published by October 2016 in primary (journal articles) and secondary (mainly laboratory reports and conference proceedings) references, together with the corresponding bibliographical information. During the development of NUBASE2016, the data available in the “Evaluated Nuclear Structure Data File” (ENSDF) database were consulted and critically assessed for their validity and completeness. Furthermore, a large amount of new datamore » and some older experimental results that were missing from ENSDF were compiled, evaluated and included in NUBASE2016. The atomic mass values were taken from the “Atomic Mass Evaluation” (AME2016, second and third parts of the present issue). In cases where no experimental data were available for a particular nuclide, trends in the behavior of specific properties in neighboring nuclides (TNN) were examined. This approach allowed to estimate values for a range of properties that are labeled in NUBASE2016 as “non-experimental” (flagged “#”). Evaluation procedures and policies used during the development of this database are presented, together with a detailed table of recommended values and their uncertainties. AMDC: http://amdc.impcas.ac.cn/« less

Gravity, aeromagnetic and rock-property data of the central California Coast Ranges

USGS Publications Warehouse

Langenheim, V.E.

2014-01-01

Gravity, aeromagnetic, and rock-property data were collected to support geologic-mapping, water-resource, and seismic-hazard studies for the central California Coast Ranges. These data are combined with existing data to provide gravity, aeromagnetic, and physical-property datasets for this region. The gravity dataset consists of approximately 18,000 measurements. The aeromagnetic dataset consists of total-field anomaly values from several detailed surveys that have been merged and gridded at an interval of 200 m. The physical property dataset consists of approximately 800 density measurements and 1,100 magnetic-susceptibility measurements from rock samples, in addition to previously published borehole gravity surveys from Santa Maria Basin, density logs from Salinas Valley, and intensities of natural remanent magnetization.

Evaluation of the 2-(1-Hexyloxyethyl)-2-devinyl pyropheophorbide (HPPH) mediated photodynamic therapy by macroscopic singlet oxygen modeling [J. Biophotonics 9, No. 11-12, 1344-1354 (2016)].

PubMed

Penjweini, Rozhin; Kim, Michele M; Liu, Baochang; Zhu, Timothy C

2017-03-01

In the article by R. Penjweini, M. M. Kim et al. (doi: 10.1002/jbio.201600121), published in J. Biophotonics 9, 1344-1354 (2016), the constants C 01 , C 02 , b 1 , and b 2 determined from fitting the fluorescence single value decomposition (SVD) for phantoms with different optical properties and the corresponding Figure 2(a) are not correct. This erratum is published to correct the Section 2.3 and Figure 2(a). © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of CMC addition on steady and dynamic shear rheological properties of binary systems of xanthan gum and guar gum.

PubMed

Bak, J H; Yoo, B

2018-04-12

The effect of CMC on the steady and dynamic shear rheological properties of binary mixtures of XG and GG was examined at different mixing ratios. All XG-GG-CMC ternary mixtures had high shear-thinning behavior and the n value of the sample with 5% CMC was the smallest compared with those of other samples. A marked increase in K and η a,50 values was observed for ternary mixtures at a lower content (5%) of CMC, indicating that the synergistic interactions of the XG-GG binary mixture were affected by the content of CMC. The effect of temperature on the η a,50 was well described by the Arrhenius equation for all samples. The activation energy values of all ternary gum mixtures are higher than that of binary gum mixture, and these values also decreased with an increase in CMC content from 5 to 15%. The dynamic moduli of ternary gum mixtures decreased with an increase in CMC content. The tan δ value of the ternary gum mixture with 5% CMC was much lower than those of other ternary mixtures. In general, these results suggest that the flow and dynamic shear rheological properties of XG-GG binary mixtures are strongly influenced by a small addition of CMC. Copyright © 2018. Published by Elsevier B.V.

Ab Initio Values of the Thermophysical Properties of Helium as Standards

PubMed Central

Hurly, John J.; Moldover, Michael R.

2000-01-01

Recent quantum mechanical calculations of the interaction energy of pairs of helium atoms are accurate and some include reliable estimates of their uncertainty. We combined these ab initio results with earlier published results to obtain a helium-helium interatomic potential that includes relativistic retardation effects over all ranges of interaction. From this potential, we calculated the thermophysical properties of helium, i.e., the second virial coefficients, the dilute-gas viscosities, and the dilute-gas thermal conductivities of 3He, 4He, and their equimolar mixture from 1 K to 104 K. We also calculated the diffusion and thermal diffusion coefficients of mixtures of 3He and 4He. For the pure fluids, the uncertainties of the calculated values are dominated by the uncertainties of the potential; for the mixtures, the uncertainties of the transport properties also include contributions from approximations in the transport theory. In all cases, the uncertainties are smaller than the corresponding experimental uncertainties; therefore, we recommend the ab initio results be used as standards for calibrating instruments relying on these thermophysical properties. We present the calculated thermophysical properties in easy-to-use tabular form. PMID:27551630

A Critical Ear: Analysis of Value Judgments in Reviews of Beethoven's Piano Sonata Recordings

PubMed Central

Alessandri, Elena; Williamson, Victoria J.; Eiholzer, Hubert; Williamon, Aaron

2016-01-01

What sets a great music performance apart? In this study, we addressed this question through an examination of value judgments in written criticism of recorded performance. One hundred reviews of recordings of Beethoven's piano sonatas, published in the Gramophone between 1934 and 2010, were analyzed through a three-step qualitative analysis that identified the valence (positive/negative) expressed by critics' statements and the evaluation criteria that underpinned their judgments. The outcome is a model of the main evaluation criteria used by professional critics: aesthetic properties, including intensity, coherence, and complexity, and achievement-related properties, including sureness, comprehension, and endeavor. The model also emphasizes how critics consider the suitability and balance of these properties across the musical and cultural context of the performance. The findings relate directly to current discourses on the role of evaluation in music criticism and the generalizability of aesthetic principles. In particular, the perceived achievement of the performer stands out as a factor that drives appreciation of a recording. PMID:27065900

The JCMT Nearby Galaxies Legacy Survey - VII. Hα imaging and massive star formation properties

NASA Astrophysics Data System (ADS)

Sánchez-Gallego, J. R.; Knapen, J. H.; Wilson, C. D.; Barmby, P.; Azimlu, M.; Courteau, S.

2012-06-01

We present Hα fluxes, star formation rates (SFRs) and equivalent widths (EWs) for a sample of 156 nearby galaxies observed in the 12CO J= 3-2 line as part of the James Clerk Maxwell Telescope Nearby Galaxies Legacy Survey. These are derived from images and values in the literature and from new Hα images for 72 galaxies which we publish here. We describe the sample, observations and procedures to extract the Hα fluxes and related quantities. We discuss the SFR properties of our sample and confirm the well-known correlation with galaxy luminosity, albeit with high dispersion. Our SFRs range from 0.1 to 11 M⊙ yr-1 with a median SFR value for the complete sample of 0.2 M⊙ yr-1. This median value is somewhat lower than similar published measurements, which we attribute, in part, to our sample being H I selected and, thus, not biased towards high SFRs as has frequently been the case in previous studies. Additionally, we calculate internal absorptions for the Hα line, A(Hα), which are lower than many of those used in previous studies. Our derived EWs, which range from 1 to 880 Å with a median value of 27 Å, show little dependence on luminosity but rise by a factor of 5 from early- to late-type galaxies. This paper is the first in a series aimed at comparing SFRs obtained from Hα imaging of galaxies with information derived from other tracers of star formation and atomic and molecular gas.

The Mexican American Cultural Values scales for Adolescents and Adults

PubMed Central

Knight, George P.; Gonzales, Nancy A.; Saenz, Delia S.; Bonds, Darya D.; Germán, Miguelina; Deardorff, Julianna; Roosa, Mark W.; Updegraff, Kimberly A.

2009-01-01

This research evaluates the properties of a measure of culturally linked values of Mexican Americans in early adolescence and adulthood. The items measure were derived from qualitative data provided by focus groups in which Mexican Americans’ (adolescents, mothers and fathers) perceptions of key values were discussed. The focus groups and a preliminary item refinement resulted in the fifty-item Mexican American Cultural Values Scales (identical for adolescents and adults) that includes nine value subscales. Analyses of data from two large previously published studies sampling Mexican American adolescents, mothers, and fathers provided evidence of the expected two correlated higher order factor structures, reliability, and construct validity of the subscales of the Mexican American Cultural Values Scales as indicators of values that are frequently associated with Mexican/Mexican American culture. The utility of this measure for use in longitudinal research, and in resolving some important theoretical questions regarding dual cultural adaptation, are discussed. PMID:20644653

Rapid experimental measurements of physicochemical properties to inform models and testing.

PubMed

Nicolas, Chantel I; Mansouri, Kamel; Phillips, Katherine A; Grulke, Christopher M; Richard, Ann M; Williams, Antony J; Rabinowitz, James; Isaacs, Kristin K; Yau, Alice; Wambaugh, John F

2018-05-02

The structures and physicochemical properties of chemicals are important for determining their potential toxicological effects, toxicokinetics, and route(s) of exposure. These data are needed to prioritize the risk for thousands of environmental chemicals, but experimental values are often lacking. In an attempt to efficiently fill data gaps in physicochemical property information, we generated new data for 200 structurally diverse compounds, which were rigorously selected from the USEPA ToxCast chemical library, and whose structures are available within the Distributed Structure-Searchable Toxicity Database (DSSTox). This pilot study evaluated rapid experimental methods to determine five physicochemical properties, including the log of the octanol:water partition coefficient (known as log(K ow ) or logP), vapor pressure, water solubility, Henry's law constant, and the acid dissociation constant (pKa). For most compounds, experiments were successful for at least one property; log(K ow ) yielded the largest return (176 values). It was determined that 77 ToxPrint structural features were enriched in chemicals with at least one measurement failure, indicating which features may have played a role in rapid method failures. To gauge consistency with traditional measurement methods, the new measurements were compared with previous measurements (where available). Since quantitative structure-activity/property relationship (QSAR/QSPR) models are used to fill gaps in physicochemical property information, 5 suites of QSPRs were evaluated for their predictive ability and chemical coverage or applicability domain of new experimental measurements. The ability to have accurate measurements of these properties will facilitate better exposure predictions in two ways: 1) direct input of these experimental measurements into exposure models; and 2) construction of QSPRs with a wider applicability domain, as their predicted physicochemical values can be used to parameterize exposure models in the absence of experimental data. Published by Elsevier B.V.

Bruise chromophore concentrations over time

NASA Astrophysics Data System (ADS)

Duckworth, Mark G.; Caspall, Jayme J.; Mappus, Rudolph L., IV; Kong, Linghua; Yi, Dingrong; Sprigle, Stephen H.

2008-03-01

During investigations of potential child and elder abuse, clinicians and forensic practitioners are often asked to offer opinions about the age of a bruise. A commonality between existing methods of bruise aging is analysis of bruise color or estimation of chromophore concentration. Relative chromophore concentration is an underlying factor that determines bruise color. We investigate a method of chromophore concentration estimation that can be employed in a handheld imaging spectrometer with a small number of wavelengths. The method, based on absorbance properties defined by Beer-Lambert's law, allows estimation of differential chromophore concentration between bruised and normal skin. Absorption coefficient data for each chromophore are required to make the estimation. Two different sources of this data are used in the analysis- generated using Independent Component Analysis and taken from published values. Differential concentration values over time, generated using both sources, show correlation to published models of bruise color change over time and total chromophore concentration over time.

The Behavior of IAPWS-95 from 250 to 300 K and Pressures up to 400 MPa: Evaluation Based on Recently Derived Property Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagner, Wolfgang, E-mail: Wagner@thermo.rub.de; Thol, Monika

2015-12-15

Over the past several years, considerable scientific and technical interest has been focused on accurate thermodynamic properties of fluid water covering part of the subcooled (metastable) region and the stable liquid from the melting line up to about 300 K and pressures up to several hundred MPa. Between 2000 and 2010, experimental density data were published whose accuracy was not completely clear. The scientific standard equation of state for fluid water, the IAPWS-95 formulation, was developed on the basis of experimental data for thermodynamic properties that were available by 1995. In this work, it is examined how IAPWS-95 behaves withmore » respect to the experimental data published after 1995. This investigation is carried out for temperatures from 250 to 300 K and pressures up to 400 MPa. The starting point is the assessment of the current data situation. This was mainly performed on the basis of data for the density, expansivity, compressibility, and isobaric heat capacity, which were derived in 2015 from very accurate speed-of-sound data. Apart from experimental data and these derived data, property values calculated from the recently published equation of state for this region of Holten et al. (2014) were also used. As a result, the unclear data situation could be clarified, and uncertainty values could be estimated for the investigated properties. In the region described above, detailed comparisons show that IAPWS-95 is able to represent the latest experimental data for the density, expansivity, compressibility, speed of sound, and isobaric heat capacity to within the uncertainties given in the release on IAPWS-95. Since the release does not contain uncertainty estimates for expansivities and compressibilities, the statement relates to the error propagation of the given uncertainty in density. Due to the lack of experimental data for the isobaric heat capacity for pressures above 100 MPa, no uncertainty estimates are given in the release for this pressure range. Results of the investigation of IAPWS-95 concerning its behavior with regard to the isobaric heat capacity in the high-pressure low-temperature region are also presented. Comparisons with very accurate speed-of-sound data published in 2012 showed that the uncertainty estimates of IAPWS-95 in speed of sound could be decreased for temperatures from 283 to 473 K and pressures up to 400 MPa.« less

Nonparametric spirometry reference values for Hispanic Americans.

PubMed

Glenn, Nancy L; Brown, Vanessa M

2011-02-01

Recent literature sites ethnic origin as a major factor in developing pulmonary function reference values. Extensive studies established reference values for European and African Americans, but not for Hispanic Americans. The Third National Health and Nutrition Examination Survey defines Hispanic as individuals of Spanish speaking cultures. While no group was excluded from the target population, sample size requirements only allowed inclusion of individuals who identified themselves as Mexican Americans. This research constructs nonparametric reference value confidence intervals for Hispanic American pulmonary function. The method is applicable to all ethnicities. We use empirical likelihood confidence intervals to establish normal ranges for reference values. Its major advantage: it is model free, but shares asymptotic properties of model based methods. Statistical comparisons indicate that empirical likelihood interval lengths are comparable to normal theory intervals. Power and efficiency studies agree with previously published theoretical results.

Vertical distribution of aerosol optical properties based on aircraft measurements over the Loess Plateau in China.

PubMed

Li, Junxia; Liu, Xingang; Yuan, Liang; Yin, Yan; Li, Zhanqing; Li, Peiren; Ren, Gang; Jin, Lijun; Li, Runjun; Dong, Zipeng; Li, Yiyu; Yang, Junmei

2015-08-01

Vertical distributions of aerosol optical properties based on aircraft measurements over the Loess Plateau were measured for the first time during a summertime aircraft campaign, 2013 in Shanxi, China. Data from four flights were analyzed. The vertical distributions of aerosol optical properties including aerosol scattering coefficients (σsc), absorption coefficients (σab), Angström exponent (α), single scattering albedo (ω), backscattering ratio (βsc), aerosol mass scattering proficiency (Qsc) and aerosol surface scattering proficiency (Qsc(')) were obtained. The mean statistical values of σsc were 77.45 Mm(-1) (at 450 nm), 50.72 Mm(-1) (at 550n m), and 32.02 Mm(-1) (at 700 nm). The mean value of σab was 7.62 Mm(-1) (at 550 nm). The mean values of α, βsc and ω were 1.93, 0.15, and 0.91, respectively. Aerosol concentration decreased with altitude. Most effective diameters (ED) of aerosols were less than 0.8 μm. The vertical profiles of σsc,, α, βsc, Qsc and Qsc(') showed that the aerosol scattering properties at lower levels contributed the most to the total aerosol radiative forcing. Both α and βsc had relatively large values, suggesting that most aerosols in the observational region were small particles. The mean values of σsc, α, βsc, Qsc, Qsc('), σab and ω at different height ranges showed that most of the parameters decreased with altitude. The forty-eight hour backward trajectories of air masses during the observation days indicated that the majority of aerosols in the lower level contributed the most to the total aerosol loading, and most of these particles originated from local or regional pollution emissions. Copyright © 2015. Published by Elsevier B.V.

Nuclear Data Sheets for A = 133

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khazov, Yu.; Rodionov, A.; Kondev, F.G.

2011-04-15

Evaluated nuclear structure and decay data for all nuclei within the A=133 mass chain are presented. The experimental data are evaluated and best values for level and gamma-ray energies, quantum numbers, lifetimes, gamma-ray intensities, and other nuclear properties are recommended. Inconsistencies and discrepancies that exist in the literature are noted. This work supersedes the earlier evaluation by S. Raab (1995Ra12), published in Nuclear Data Sheets75, 491 (1995).

Self-consistent DFT +U method for real-space time-dependent density functional theory calculations

NASA Astrophysics Data System (ADS)

Tancogne-Dejean, Nicolas; Oliveira, Micael J. T.; Rubio, Angel

2017-12-01

We implemented various DFT+U schemes, including the Agapito, Curtarolo, and Buongiorno Nardelli functional (ACBN0) self-consistent density-functional version of the DFT +U method [Phys. Rev. X 5, 011006 (2015), 10.1103/PhysRevX.5.011006] within the massively parallel real-space time-dependent density functional theory (TDDFT) code octopus. We further extended the method to the case of the calculation of response functions with real-time TDDFT+U and to the description of noncollinear spin systems. The implementation is tested by investigating the ground-state and optical properties of various transition-metal oxides, bulk topological insulators, and molecules. Our results are found to be in good agreement with previously published results for both the electronic band structure and structural properties. The self-consistent calculated values of U and J are also in good agreement with the values commonly used in the literature. We found that the time-dependent extension of the self-consistent DFT+U method yields improved optical properties when compared to the empirical TDDFT+U scheme. This work thus opens a different theoretical framework to address the nonequilibrium properties of correlated systems.

The flexural properties of endodontic post materials.

PubMed

Stewardson, Dominic A; Shortall, Adrian C; Marquis, Peter M; Lumley, Philip J

2010-08-01

To measure the flexural strengths and moduli of endodontic post materials and to assess the effect on the calculated flexural properties of varying the diameter/length (D/L) ratio of three-point bend test samples. Three-point bend testing of samples of 2mm diameter metal and fiber-reinforced composite (FRC) rods was carried out and the mechanical properties calculated at support widths of 16 mm, 32 mm and 64 mm. Weibull analysis was performed on the strength data. The flexural strengths of all the FRC post materials exceeded the yield strengths of the gold and stainless steel samples; the flexural strengths of two FRC materials were comparable with the yield strength of titanium. Stainless steel recorded the highest flexural modulus while the titanium and the two carbon fiber materials exhibited similar values just exceeding that of gold. The remaining glass fiber materials were of lower modulus within the range of 41-57 GPa. Weibull modulus values for the FRC materials ranged from 16.77 to 30.09. Decreasing the L/D ratio produced a marked decrease in flexural modulus for all materials. The flexural strengths of FRC endodontic post materials as new generally exceed the yield strengths of metals from which endodontic posts are made. The high Weibull modulus values suggest good clinical reliability of FRC posts. The flexural modulus values of the tested posts were from 2-6 times (FRC) to 4-10 times (metal) that of dentin. Valid measurement of flexural properties of endodontic post materials requires that test samples have appropriate L/D ratios. Copyright 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Physical, mechanical, and flexural properties of 3 orthodontic wires: an in-vitro study.

PubMed

Juvvadi, Shubhaker Rao; Kailasam, Vignesh; Padmanabhan, Sridevi; Chitharanjan, Arun B

2010-11-01

Understanding the biologic requirements of orthodontic patients requires proper characterization studies of new archwire alloys. The aims of this study were to evaluate properties of wires made of 2 new materials and to compare their properties with those of stainless steel. The sample consisted of 30 straight lengths of 3 types of wires: stainless steel, titanium-molybdenum alloy, and beta-titanium alloy. Eight properties were evaluated: wire dimension, edge bevel, composition, surface characteristics, frictional characteristics, ultimate tensile strength (UTS), modulus of elasticity (E), yield strength (YS), and load deflection characteristics. A toolmaker's microscope was used to measure the edge bevel, and x-ray fluorescence was used for composition analysis. Surface profilometry and scanning electron microscopy were used for surface evaluation. A universal testing machine was used to evaluate frictional characteristics, tensile strength, and 3-point bending. Stainless steel was the smoothest wire; it had the lowest friction and spring-back values and high values for stiffness, E, YS, and UTS. The titanium-molybdenum alloy was the roughest wire; it had high friction and intermediate spring-back, stiffness, and UTS values. The beta-titanium alloy was intermediate for smoothness, friction, and UTS but had the highest spring-back. The beta-titanium alloy with increased UTS and YS had a low E value, suggesting that it would have greater resistance to fracture, thereby overcoming a major disadvantage of titanium-molybdenum alloy wires. The beta-titanium alloy wire would also deliver gentler forces. Copyright © 2010 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Modeling englacial radar attenuation at Siple Dome, West Antarctica, using ice chemistry and temperature data

USGS Publications Warehouse

MacGregor, J.A.; Winebrenner, D.P.; Conway, H.; Matsuoka, K.; Mayewski, P.A.; Clow, G.D.

2007-01-01

The radar reflectivity of an ice-sheet bed is a primary measurement for discriminating between thawed and frozen beds. Uncertainty in englacial radar attenuation and its spatial variation introduces corresponding uncertainty in estimates of basal reflectivity. Radar attenuation is proportional to ice conductivity, which depends on the concentrations of acid and sea-salt chloride and the temperature of the ice. We synthesize published conductivity measurements to specify an ice-conductivity model and find that some of the dielectric properties of ice at radar frequencies are not yet well constrained. Using depth profiles of ice-core chemistry and borehole temperature and an average of the experimental values for the dielectric properties, we calculate an attenuation rate profile for Siple Dome, West Antarctica. The depth-averaged modeled attenuation rate at Siple Dome (20.0 ?? 5.7 dB km-1) is somewhat lower than the value derived from radar profiles (25.3 ?? 1.1 dB km-1). Pending more experimental data on the dielectric properties of ice, we can match the modeled and radar-derived attenuation rates by an adjustment to the value for the pure ice conductivity that is within the range of reported values. Alternatively, using the pure ice dielectric properties derived from the most extensive single data set, the modeled depth-averaged attenuation rate is 24.0 ?? 2.2 dB km-1. This work shows how to calculate englacial radar attenuation using ice chemistry and temperature data and establishes a basis for mapping spatial variations in radar attenuation across an ice sheet. Copyright 2007 by the American Geophysical Union.

Comparing quantitative values of two generations of laser-assisted indocyanine green dye angiography systems: can we predict necrosis?

PubMed

Phillips, Brett T; Fourman, Mitchell S; Rivara, Andrew; Dagum, Alexander B; Huston, Tara L; Ganz, Jason C; Bui, Duc T; Khan, Sami U

2014-01-01

Several devices exist today to assist the intraoperative determination of skin flap perfusion. Laser-Assisted Indocyanine Green Dye Angiography (LAICGA) has been shown to accurately predict mastectomy skin flap necrosis using quantitative perfusion values. The laser properties of the latest LAICGA device (SPY Elite) differ significantly from its predecessor system (SPY 2001), preventing direct translation of previous published data. The purpose of this study was to establish a mathematical relationship of perfusion values between these 2 devices. Breast reconstruction patients were prospectively enrolled into a clinical trial where skin flap evaluation and excision was based on quantitative SPY Q values previously established in the literature. Initial study patients underwent mastectomy skin flap evaluation using both SPY systems simultaneously. Absolute perfusion unit (APU) values at identical locations on the breast were then compared graphically. 210 data points were identified on the same patients (n = 4) using both SPY systems. A linear relationship (y = 2.9883x + 12.726) was identified with a high level or correlation (R(2) = 0.744). Previously published values using SPY 2001 (APU 3.7) provided a value of 23.8 APU on the SPY Elite. In addition, postoperative necrosis in these patients correlated to regions of skin identified with the SPY Elite with APU less than 23.8. Intraoperative comparison of LAICGA systems has provided direct correlation of perfusion values predictive of necrosis that were previously established in the literature. An APU value of 3.7 from the SPY 2001 correlates to a SPY Elite APU value of 23.8.

Comparing Quantitative Values of Two Generations of Laser-Assisted Indocyanine Green Dye Angiography Systems: Can We Predict Necrosis?

PubMed Central

Fourman, Mitchell S.; Rivara, Andrew; Dagum, Alexander B.; Huston, Tara L.; Ganz, Jason C.; Bui, Duc T.; Khan, Sami U.

2014-01-01

Objective: Several devices exist today to assist the intraoperative determination of skin flap perfusion. Laser-Assisted Indocyanine Green Dye Angiography (LAICGA) has been shown to accurately predict mastectomy skin flap necrosis using quantitative perfusion values. The laser properties of the latest LAICGA device (SPY Elite) differ significantly from its predecessor system (SPY 2001), preventing direct translation of previous published data. The purpose of this study was to establish a mathematical relationship of perfusion values between these 2 devices. Methods: Breast reconstruction patients were prospectively enrolled into a clinical trial where skin flap evaluation and excision was based on quantitative SPY Q values previously established in the literature. Initial study patients underwent mastectomy skin flap evaluation using both SPY systems simultaneously. Absolute perfusion unit (APU) values at identical locations on the breast were then compared graphically. Results: 210 data points were identified on the same patients (n = 4) using both SPY systems. A linear relationship (y = 2.9883x + 12.726) was identified with a high level or correlation (R2 = 0.744). Previously published values using SPY 2001 (APU 3.7) provided a value of 23.8 APU on the SPY Elite. In addition, postoperative necrosis in these patients correlated to regions of skin identified with the SPY Elite with APU less than 23.8. Conclusion: Intraoperative comparison of LAICGA systems has provided direct correlation of perfusion values predictive of necrosis that were previously established in the literature. An APU value of 3.7 from the SPY 2001 correlates to a SPY Elite APU value of 23.8. PMID:25525483

Ambiguity in Social Network Data for Presence, Sensitive-Attribute, Degree and Relationship Privacy Protection.

PubMed

Rajaei, Mehri; Haghjoo, Mostafa S; Miyaneh, Eynollah Khanjari

2015-01-01

Maintaining privacy in network data publishing is a major challenge. This is because known characteristics of individuals can be used to extract new information about them. Recently, researchers have developed privacy methods based on k-anonymity and l-diversity to prevent re-identification or sensitive label disclosure through certain structural information. However, most of these studies have considered only structural information and have been developed for undirected networks. Furthermore, most existing approaches rely on generalization and node clustering so may entail significant information loss as all properties of all members of each group are generalized to the same value. In this paper, we introduce a framework for protecting sensitive attribute, degree (the number of connected entities), and relationships, as well as the presence of individuals in directed social network data whose nodes contain attributes. First, we define a privacy model that specifies privacy requirements for the above private information. Then, we introduce the technique of Ambiguity in Social Network data (ASN) based on anatomy, which specifies how to publish social network data. To employ ASN, individuals are partitioned into groups. Then, ASN publishes exact values of properties of individuals of each group with common group ID in several tables. The lossy join of those tables based on group ID injects uncertainty to reconstruct the original network. We also show how to measure different privacy requirements in ASN. Simulation results on real and synthetic datasets demonstrate that our framework, which protects from four types of private information disclosure, preserves data utility in tabular, topological and spectrum aspects of networks at a satisfactory level.

Ambiguity in Social Network Data for Presence, Sensitive-Attribute, Degree and Relationship Privacy Protection

PubMed Central

Rajaei, Mehri; Haghjoo, Mostafa S.; Miyaneh, Eynollah Khanjari

2015-01-01

Maintaining privacy in network data publishing is a major challenge. This is because known characteristics of individuals can be used to extract new information about them. Recently, researchers have developed privacy methods based on k-anonymity and l-diversity to prevent re-identification or sensitive label disclosure through certain structural information. However, most of these studies have considered only structural information and have been developed for undirected networks. Furthermore, most existing approaches rely on generalization and node clustering so may entail significant information loss as all properties of all members of each group are generalized to the same value. In this paper, we introduce a framework for protecting sensitive attribute, degree (the number of connected entities), and relationships, as well as the presence of individuals in directed social network data whose nodes contain attributes. First, we define a privacy model that specifies privacy requirements for the above private information. Then, we introduce the technique of Ambiguity in Social Network data (ASN) based on anatomy, which specifies how to publish social network data. To employ ASN, individuals are partitioned into groups. Then, ASN publishes exact values of properties of individuals of each group with common group ID in several tables. The lossy join of those tables based on group ID injects uncertainty to reconstruct the original network. We also show how to measure different privacy requirements in ASN. Simulation results on real and synthetic datasets demonstrate that our framework, which protects from four types of private information disclosure, preserves data utility in tabular, topological and spectrum aspects of networks at a satisfactory level. PMID:26110762

Properties of behavior under different random ratio and random interval schedules: A parametric study.

PubMed

Dembo, M; De Penfold, J B; Ruiz, R; Casalta, H

1985-03-01

Four pigeons were trained to peck a key under different values of a temporally defined independent variable (T) and different probabilities of reinforcement (p). Parameter T is a fixed repeating time cycle and p the probability of reinforcement for the first response of each cycle T. Two dependent variables were used: mean response rate and mean postreinforcement pause. For all values of p a critical value for the independent variable T was found (T=1 sec) in which marked changes took place in response rate and postreinforcement pauses. Behavior typical of random ratio schedules was obtained at T 1 sec and behavior typical of random interval schedules at T 1 sec. Copyright © 1985. Published by Elsevier B.V.

Hydraulic and mechanical properties affecting ground-water flow and aquifer-system compaction, San Joaquin Valley, California

USGS Publications Warehouse

Sneed, Michelle

2001-01-01

This report summarizes hydraulic and mechanical properties affecting ground-water flow and aquifer-system compaction in the San Joaquin Valley, a broad alluviated intermontane structural trough that constitutes the southern two-thirds of the Central Valley of California. These values will be used to constrain a coupled ground-water flow and aquifer-system compaction model of the western San Joaquin Valley called WESTSIM. A main objective of the WESTSIM model is to evaluate potential future land subsidence that might occur under conditions in which deliveries of imported surface water for agricultural use are reduced and ground-water pumping is increased. Storage values generally are components of the total aquifer-system storage and include inelastic and elastic skeletal storage values of the aquifers and the aquitards that primarily govern the potential amount of land subsidence. Vertical hydraulic conductivity values generally are for discrete thicknesses of sediments, usually aquitards, that primarily govern the rate of land subsidence. The data were compiled from published sources and include results of aquifer tests, stress-strain analyses of borehole extensometer observations, laboratory consolidation tests, and calibrated models of aquifer-system compaction.

Triprotic site-specific acid-base equilibria and related properties of fluoroquinolone antibacterials.

PubMed

Rusu, Aura; Tóth, Gergő; Szőcs, Levente; Kökösi, József; Kraszni, Márta; Gyéresi, Árpád; Noszál, Béla

2012-07-01

The complete macro- and microequilibrium analyses of six fluoroquinolone drugs - ciprofloxacin, enrofloxacin, norfloxacin, pefloxacin, ofloxacin and moxifloxacin - are presented. Previous controversial literature data are straightened up, the protonation centers are unambiguously identified, and the protonation macro- and microconstant values are reported. The macroconstants were determined by (1)H NMR-pH titrations while the microconstants were determined by a multi-modal spectroscopic-deductive methodology, in which methyl ester derivatives were synthesized and their NMR-pH titration data contributed to the evaluation of all the microconstants. The full (1)H, (13)C and (15)N NMR assignments, NMR-pH profiles, macro- and microprotonation schemes and species-specific diagrams are included. Our studies show that the fluoroquinolones have three protonation centers: the carboxylate group, the N-1' and N-4' piperazine nitrogens and concentration of the uncharged microspecies is way below the values published earlier. The results could be well interpreted in terms of structural properties. The protonation macro- and microconstant values allow the pre-planned method development in techniques such as capillary zone electrophoresis and also, the interpretation of fluoroquinolone mechanism of biological action, including the pharmacokinetic properties, and antibacterial activities that are all heavily influenced by the states of protonation. Copyright © 2012 Elsevier B.V. All rights reserved.

Nuclear Data Sheets for A = 146

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khazov, Yu.; Rodionov, A.; Shulyak, G.

Evaluated nuclear structure and decay data for all nuclei within the A = 146 mass chain are presented. The experimental data are evaluated and best values for level and gamma-ray energies, quantum numbers, lifetimes, gamma-ray intensities, and other nuclear properties are recommended. Inconsistencies and discrepancies that exist in the literature are noted. This work supersedes the earlier evaluation by L.K. Peker, J.K. Tuli (1997Pe22), published in Nuclear Data Sheets82, 187 (1997).

Nuclear Data Sheets for A = 146

NASA Astrophysics Data System (ADS)

Khazov, Yu.; Rodionov, A.; Shulyak, G.

2016-09-01

Evaluated nuclear structure and decay data for all nuclei within the A = 146 mass chain are presented. The experimental data are evaluated and best values for level and gamma-ray energies, quantum numbers, lifetimes, gamma-ray intensities, and other nuclear properties are recommended. Inconsistencies and discrepancies that exist in the literature are noted. This work supersedes the earlier evaluation by L.K. Peker, J.K. Tuli (1997Pe22), published in Nuclear Data Sheets82, 187 (1997).

A Comparison of EQ-5D-3L Index Scores Using Malaysian, Singaporean, Thai, and UK Value Sets in Indonesian Cervical Cancer Patients.

PubMed

Endarti, Dwi; Riewpaiboon, Arthorn; Thavorncharoensap, Montarat; Praditsitthikorn, Naiyana; Hutubessy, Raymond; Kristina, Susi Ari

2018-05-01

To gain insight into the most suitable foreign value set among Malaysian, Singaporean, Thai, and UK value sets for calculating the EuroQol five-dimensional questionnaire index score (utility) among patients with cervical cancer in Indonesia. Data from 87 patients with cervical cancer recruited from a referral hospital in Yogyakarta province, Indonesia, from an earlier study of health-related quality of life were used in this study. The differences among the utility scores derived from the four value sets were determined using the Friedman test. Performance of the psychometric properties of the four value sets versus visual analogue scale (VAS) was assessed. Intraclass correlation coefficients and Bland-Altman plots were used to test the agreement among the utility scores. Spearman ρ correlation coefficients were used to assess convergent validity between utility scores and patients' sociodemographic and clinical characteristics. With respect to known-group validity, the Kruskal-Wallis test was used to examine the differences in utility according to the stages of cancer. There was significant difference among utility scores derived from the four value sets, among which the Malaysian value set yielded higher utility than the other three value sets. Utility obtained from the Malaysian value set had more agreements with VAS than the other value sets versus VAS (intraclass correlation coefficients and Bland-Altman plot tests results). As for the validity, the four value sets showed equivalent psychometric properties as those that resulted from convergent and known-group validity tests. In the absence of an Indonesian value set, the Malaysian value set was more preferable to be used compared with the other value sets. Further studies on the development of an Indonesian value set need to be conducted. Copyright © 2018. Published by Elsevier Inc.

Parameterization of Keeling's network generation algorithm.

PubMed

Badham, Jennifer; Abbass, Hussein; Stocker, Rob

2008-09-01

Simulation is increasingly being used to examine epidemic behaviour and assess potential management options. The utility of the simulations rely on the ability to replicate those aspects of the social structure that are relevant to epidemic transmission. One approach is to generate networks with desired social properties. Recent research by Keeling and his colleagues has generated simulated networks with a range of properties, and examined the impact of these properties on epidemic processes occurring over the network. However, published work has included only limited analysis of the algorithm itself and the way in which the network properties are related to the algorithm parameters. This paper identifies some relationships between the algorithm parameters and selected network properties (mean degree, degree variation, clustering coefficient and assortativity). Our approach enables users of the algorithm to efficiently generate a network with given properties, thereby allowing realistic social networks to be used as the basis of epidemic simulations. Alternatively, the algorithm could be used to generate social networks with a range of property values, enabling analysis of the impact of these properties on epidemic behaviour.

Experimental Data and Guidelines for Stone Masonry Structures: a Comparative Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romano, Alessandra

2008-07-08

Indications about the mechanical properties of masonry structures contained in many Italian guidelines are based on different aspects both concerning the constituents material (units and mortar) and their assemblage. Indeed, the documents define different classes (depending on the type, the arrangement and the unit properties) and suggest the use of amplification coefficients for taking into account the influence of different factors on the mechanical properties of masonry. In this paper, a critical discussion about the indications proposed by some Italian guidelines for stone masonry structures is presented. Particular attention is addressed to the classification criteria of the masonry type andmore » to the choice of the amplification factors. Finally, a detailed analytical comparison among the suggested values and some inherent experimental data recently published is performed.« less

Characterization of Radiation Fields in Biological Shields of Nuclear Power Plants for Assessing Concrete Degradation

NASA Astrophysics Data System (ADS)

Remec, Igor; Rosseel, Thomas M.; Field, Kevin G.; Le Pape, Yann

2016-02-01

Life extensions of nuclear power plants to 60 and potentially 80 years of operation have renewed interest in long-term material degradation. One material being considered is concrete, with a particular focus on radiation-induced effects. Based on the projected neutron fluence values (E > 0.1 MeV) in the concrete biological shields of the US pressurized water reactor fleet and the available data on radiation effects on concrete, some decrease in mechanical properties of concrete cannot be ruled out during extended operation beyond 60 years. An expansion of the irradiated concrete database and a reliable determination of relevant neutron fluence energy cutoff value are necessary to ensure reliable risk assessment for extended operation of nuclear power plants. Notice: This manuscript has been authored by UT-Battelle, LLC, under contract DE-AC0500OR22725 with the US Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a nonexclusive, paid-up, irrevocable, worldwide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes.

Predictive ecotoxicity of MoA 1 of organic chemicals using in silico approaches.

PubMed

de Morais E Silva, Luana; Alves, Mateus Feitosa; Scotti, Luciana; Lopes, Wilton Silva; Scotti, Marcus Tullius

2018-05-30

Persistent organic products are compounds used for various purposes, such as personal care products, surfactants, colorants, industrial additives, food, pesticides and pharmaceuticals. These substances are constantly introduced into the environment and many of these pollutants are difficult to degrade. Toxic compounds classified as MoA 1 (Mode of Action 1) are low toxicity compounds that comprise nonreactive chemicals. In silico methods such as Quantitative Structure-Activity Relationships (QSARs) have been used to develop important models for prediction in several areas of science, as well as aquatic toxicity studies. The aim of the present study was to build a QSAR model-based set of theoretical Volsurf molecular descriptors using the fish acute toxicity values of compounds defined as MoA 1 to identify the molecular properties related to this mechanism. The selected Partial Least Squares (PLS) results based on the values of cross-validation coefficients of determination (Q cv 2 ) show the following values: Q cv 2 = 0.793, coefficient of determination (R 2 ) = 0.823, explained variance in external prediction (Q ext 2 ) = 0.87. From the selected descriptors, not only the hydrophobicity is related to the toxicity as already mentioned in previously published studies but other physicochemical properties combined contribute to the activity of these compounds. The symmetric distribution of the hydrophobic moieties in the structure of the compounds as well as the shape, as branched chains, are important features that are related to the toxicity. This information from the model can be useful in predicting so as to minimize the toxicity of organic compounds. Copyright © 2018. Published by Elsevier Inc.

Alteration of dentin-enamel mechanical properties due to dental whitening treatments.

PubMed

Zimmerman, B; Datko, L; Cupelli, M; Alapati, S; Dean, D; Kennedy, M

2010-05-01

The mechanical properties of dentin and enamel affect the reliability and wear properties of a tooth. This study investigated the influence of clinical dental treatments and procedures, such as whitening treatments or etching prior to restorative procedures. Both autoclaved and non-autoclaved teeth were studied in order to allow for both comparison with published values and improved clinical relevance. Nanoindentation analysis with the Oliver-Pharr model provided elastic modulus and hardness across the dentin-enamel junction (DEJ). Large increases were observed in the elastic modulus of enamel in teeth that had been autoclaved (52.0 GPa versus 113.4 GPa), while smaller increases were observed in the dentin (17.9 GPa versus 27.9 GPa). Likewise, there was an increase in the hardness of enamel (2.0 GPa versus 4.3 GPa) and dentin (0.5 GPa versus 0.7 GPa) with autoclaving. These changes suggested that the range of elastic modulus and hardness values previously reported in the literature may be partially due to the sterilization procedures. Treatment of the exterior of non-autoclaved teeth with Crest Whitestrips, Opalescence or UltraEtch caused changes in the mechanical properties of both the enamel and dentin. Those treated with Crest Whitestrips showed a reduction in the elastic modulus of enamel (55.3 GPa to 32.7 GPa) and increase in the elastic modulus of dentin (17.2 GPa to 24.3 GPa). Opalescence treatments did not significantly affect the enamel properties, but did result in a decrease in the modulus of dentin (18.5 GPa to 15.1 GPa). Additionally, as expected, UltraEtch treatment decreased the modulus and hardness of enamel (48.7 GPa to 38.0 GPa and 1.9 GPa to 1.5 GPa, respectively) and dentin (21.4 GPa to 15.0 GPa and 1.9 GPa to 1.5 GPa, respectively). Changes in the mechanical properties were linked to altered protein concentration within the tooth, as evidenced by fluorescence microscopy and Fourier transform infrared spectroscopy. Published by Elsevier Ltd.

Spectral reflectance of surface soils: Relationships with some soil properties

NASA Technical Reports Server (NTRS)

Kiesewetter, C. H.

1983-01-01

Using a published atlas of reflectance curves and physicochemical properties of soils, a statistical analysis was carried out. Reflectance bands which correspond to five of the wavebands used by NASA's Thematic Mapper were examined for relationships to specific soil properties. The properties considered in this study include: Sand Content, Silt Content, Clay Content, Organic Matter Content, Cation Exchange Capacity, Iron Oxide Content and Moisture Content. Regression of these seven properties on the mean values of five TM bands produced results that indicate that the predictability of the properties can be increased by stratifying the data. The data was stratified by parent material, taxonomic order, temperature zone, moisture zone and climate (combined temperature and moisture). The best results were obtained when the sample was examined by climatic classes. The middle Infra-red bands, 5 and 7, as well as the visible bands, 2 and 3, are significant in the model. The near Infra-red band, band 4, is almost as useful and should be included in any studies. General linear modeling procedures examined relationships of the seven properties with certain wavebands in the stratified samples.

Relevant optical properties for direct restorative materials.

PubMed

Pecho, Oscar E; Ghinea, Razvan; do Amaral, Erika A Navarro; Cardona, Juan C; Della Bona, Alvaro; Pérez, María M

2016-05-01

To evaluate relevant optical properties of esthetic direct restorative materials focusing on whitened and translucent shades. Enamel (E), body (B), dentin (D), translucent (T) and whitened (Wh) shades for E (WhE) and B (WhB) from a restorative system (Filtek Supreme XTE, 3M ESPE) were evaluated. Samples (1 mm thick) were prepared. Spectral reflectance (R%) and color coordinates (L*, a*, b*, C* and h°) were measured against black and white backgrounds, using a spectroradiometer, in a viewing booth, with CIE D65 illuminant and d/0° geometry. Scattering (S) and absorption (K) coefficients and transmittance (T%) were calculated using Kubelka-Munk's equations. Translucency (TP) and opalescence (OP) parameters and whiteness index (W*) were obtained from differences of CIELAB color coordinates. R%, S, K and T% curves from all shades were compared using VAF (Variance Accounting For) coefficient with Cauchy-Schwarz inequality. Color coordinates and optical parameters were statistically analyzed using one-way ANOVA, Tukey's test with Bonferroni correction (α=0.0007). Spectral behavior of R% and S were different for T shades. In addition, T shades showed the lowest R%, S and K values, as well as the highest T%, TP an OP values. In most cases, WhB shades showed different color and optical properties (including TP and W*) than their corresponding B shades. WhE shades showed similar mean W* values and higher mean T% and TP values than E shades. When using whitened or translucent composites, the final color is influenced not only by the intraoral background but also by the color and optical properties of multilayers used in the esthetic restoration. Copyright © 2016 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Fragment-based approach to calculate hydrophobicity of anionic and nonionic surfactants derived from chromatographic retention on a C18 stationary phase.

PubMed

Hammer, Jort; Haftka, Joris J-H; Scherpenisse, Peter; Hermens, Joop L M; de Voogt, Pim W P

2017-02-01

To predict the fate and potential effects of organic contaminants, information about their hydrophobicity is required. However, common parameters to describe the hydrophobicity of organic compounds (e.g., octanol-water partition constant [K OW ]) proved to be inadequate for ionic and nonionic surfactants because of their surface-active properties. As an alternative approach to determine their hydrophobicity, the aim of the present study was therefore to measure the retention of a wide range of surfactants on a C 18 stationary phase. Capacity factors in pure water (k' 0 ) increased linearly with increasing number of carbon atoms in the surfactant structure. Fragment contribution values were determined for each structural unit with multilinear regression, and the results were consistent with the expected influence of these fragments on the hydrophobicity of surfactants. Capacity factors of reference compounds and log K OW values from the literature were used to estimate log K OW values for surfactants (log KOWHPLC). These log KOWHPLC values were also compared to log K OW values calculated with 4 computational programs: KOWWIN, Marvin calculator, SPARC, and COSMOThermX. In conclusion, capacity factors from a C 18 stationary phase are found to better reflect hydrophobicity of surfactants than their K OW values. Environ Toxicol Chem 2017;36:329-336. © 2016 The Authors. Environmental Toxicology and Chemistry Published by Wiley Periodicals, Inc. on behalf of SETAC. © 2016 The Authors. Environmental Toxicology and Chemistry Published by Wiley Periodicals, Inc. on behalf of SETAC.

Estimation of ZnSe Slow-Crack-Growth Properties for Design of the Flow Enclosure Accommodating Novel Investigations in Combustion of Solids (FEANICS) Windows

NASA Technical Reports Server (NTRS)

Salem, Jonathan A.

2005-01-01

This report reviews some of the literature on the fracture strength, fracture toughness, and crack growth properties of chemical-vapor-deposited ZnSe. The literature was reviewed to determine if the existing data on ZnSe is adequate to design windows for the Flow Enclosure Accommodating Novel Investigations in Combustion of Solids (FEANICS) project. Unfortunately, most of the published reports do not give all of the necessary design parameters despite having measured the data to do so. Further, the original data is not available. The data tabulated herein was determined by digitizing plots in original reprints of the publications. Based on the published data, an estimate of the slow-crack-growth parameters for small cracks in 100 percent humidity was made. For 100 percent humidity, the slow-crack-growth parameters n and A for small crack (or single crystal) failure were estimated. Weibull moduli estimated from bending of beams and circular plates ranged from 4 to 9, while fracture strengths ranged from 29 MPa in water to 72 MPa in dry nitrogen. Fracture toughness measurements yielded ranges, with the lower values representing failure from small flaws within grains and the larger values representing macroscopic cracks. Much of the data analyzed exhibited significant scatter, and the standard deviations were very large.

Kepler Stellar Properties Catalog Update for Q1-Q17 DR25 Transit Search

NASA Technical Reports Server (NTRS)

Mathur, Savita; Huber, Daniel

2016-01-01

Huber et al. (2014) presented revised stellar properties for 196,468 Kepler targets, which were used for the Q1-Q16 TPSDV planet search (Tenenbaum et al. 2014). The catalog was based on atmospheric properties (i.e., temperature (Teff), surface gravity (log(g)), and metallicity ([FeH])) published in the literature using a variety of methods (e.g., asteroseismology, spectroscopy, exoplanet transits, photometry), which were then homogeneously fitted to a grid of Dartmouth (DSEP) isochrones (Dotter et al. 2008). The catalog was updated in early 2015 for the Q1-Q17 Data Release (DR) 24 transit search (Seader et al. 2015) based on the latest classifications of Kepler targets in the literature at that time. The methodology followed Huber et al. (2014). Here we provide updated stellar properties of 197,096 Kepler targets. Like the previous catalog, this update is based on atmospheric properties that were either published in the literature or provided by the Kepler community follow-up program (CFOP). The input values again come from different methods: asteroseismology, spectroscopy, flicker, and photometry. This catalog update was developed to support the SOC 9.3 TPSDV planet search (Twicken et al. 2016), which is expected to be the final search and data release by the Kepler project.In this document, we describe the method and the inputs that were used to build the catalog. The methodology follows Huber et al. (2014) with a few improvements as described in Section 2.

Comparisons of nanoindentation, 3-point bending, and tension tests for orthodontic wires.

PubMed

Iijima, Masahiro; Muguruma, Takeshi; Brantley, William A; Mizoguchi, Itaru

2011-07-01

The purposes of this study were to obtain information about mechanical properties with the nanoindentation test for representative wire alloys and compare the results with conventional mechanical tests. Archwires having 0.016 × 0.022-in cross sections were obtained of 1 stainless steel, 1 cobalt-chromium-nickel, 1 beta-titanium alloy, and 2 nickel-titanium products. Specimens of as-received wires were subjected to nanoindentation testing along the external surfaces and over polished cross sections to obtain values of hardness and elastic modulus. Other specimens of as-received wires were subjected to Vickers hardness, 3-point bending, and tension tests. All testing was performed at 25°C. Differences were found in hardness and elastic modulus obtained with the nanoindentation test at the external and cross-sectioned surfaces and with the conventional mechanical-property tests. Mechanical properties obtained with the nanoindentation test generally varied with indentation depth. The 3 testing methods did not yield identical values of hardness and elastic modulus, although the order among the 5 wire products was the same. Variations in results for the nanoindentation and conventional mechanical property tests can be attributed to the different material volumes sampled, different work-hardening levels, and an oxide layer on the wire surface. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Influence of lactose addition to gentamicin-loaded acrylic bone cement on the kinetics of release of the antibiotic and the cement properties.

PubMed

Frutos, Gloria; Pastor, José Ygnacio; Martínez, Noelia; Virto, María Rosa; Torrado, Susana

2010-03-01

The purpose of this study was to characterize a poly(methyl methacrylate) bone cement that was loaded with the antibiotic gentamicin sulphate (GS) and lactose, which served to modulate the release of GS from cement specimens. The release of GS when the cement specimens were immersed in phosphate-buffered saline at 37 degrees Celsius was determined spectrophotometrically. The microstructure, porosity, density, tensile properties and flexural properties of the cements were determined before and after release of GS. A kinetics model of the release of GS from the cement that involved a coupled mechanism based on dissolution/diffusion processes and an initial burst effect was proposed. Dissolution assay results showed that drug elution was controlled by a diffusion mechanism which can be modulated by lactose addition. Density values and mechanical properties (tensile strength, flexural strength, elastic modulus and fracture toughness) were reduced by the increased porosity resulting from lactose addition, but maintained acceptable values for the structural functions of bone cement. The present results suggest that lactose-modified, gentamicin-loaded acrylic bone cements are potential candidates for use in various orthopaedic and dental applications. Copyright 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Determination of the biotin content of select foods using accurate and sensitive HPLC/avidin binding

PubMed Central

Staggs, C.G.; Sealey, W.M.; McCabe, B.J.; Teague, A.M.; Mock, D.M.

2006-01-01

Assessing dietary biotin content, biotin bioavailability, and resulting biotin status are crucial in determining whether biotin deficiency is teratogenic in humans. Accuracy in estimating dietary biotin is limited both by data gaps in food composition tables and by inaccuracies in published data. The present study applied sensitive and specific analytical techniques to determine values for biotin content in a select group of foods. Total biotin content of 87 foods was determined using acid hydrolysis and the HPLC/avidin-binding assay. These values are consistent with published values in that meat, fish, poultry, egg, dairy, and some vegetables are relatively rich sources of biotin. However, these biotin values disagreed substantially with published values for many foods. Assay values varied between 247 times greater than published values for a given food to as much as 36% less than the published biotin value. Among 51 foods assayed for which published values were available, only seven agreed within analytical variability (720%). We conclude that published values for biotin content of foods are likely to be inaccurate. PMID:16648879

Structural Design and Physicochemical Foundations of Hydrogels for Biomedical Applications.

PubMed

Li, Qingyong; Ning, Zhengxiang; Ren, Jiaoyan; Liao, Wenzhen

2018-01-01

Biomedical research, known as medical research, is conducive to support and promote the development of knowledge in the field of medicine. Hydrogels have been extensively used in many biomedical fields due to their highly absorbent and flexible properties. The smart hydrogels, especially, can respond to a broad range of external stimuli such as temperature, pH value, light, electric and magnetic fields. With excellent biocompatibility, tunable rheology, mechanical properties, porosity, and hydrated molecular structure, hydrogels are considered as promising candidate for simulating local tissue microenvironment. In this review article, we mainly focused on the most recent development of engineering synthetic hydrogels; moreover, the classification, properties, especially the biomedical applications including tissue engineering and cell scaffolding, drug and gene delivery, immunotherapies and vaccines, are summarized and discussed. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

A chondroitinase-ABC and TGF-β1 treatment regimen for enhancing the mechanical properties of tissue-engineered fibrocartilage.

PubMed

MacBarb, Regina F; Makris, Eleftherios A; Hu, Jerry C; Athanasiou, Kyriacos A

2013-01-01

The development of functionally equivalent fibrocartilage remains elusive despite efforts to engineer tissues such as knee meniscus, intervertebral disc and temporomandibular joint disc. Attempts to engineer these structures often fail to create tissues with mechanical properties on a par with native tissue, resulting in constructs unsuitable for clinical applications. The objective of this study was to engineer a spectrum of biomimetic fibrocartilages representative of the distinct functional properties found in native tissues. Using the self-assembly process, different co-cultures of meniscus cells and articular chondrocytes were seeded into agarose wells and treated with the catabolic agent chondroitinase-ABC (C-ABC) and the anabolic agent transforming growth factor-β1 (TGF-β1) via a two-factor (cell ratio and bioactive treatment), full factorial study design. Application of both C-ABC and TGF-β1 resulted in a beneficial or positive increase in the collagen content of treated constructs compared to controls. Significant increases in both the collagen density and fiber diameter were also seen with this treatment, increasing these values by 32 and 15%, respectively, over control values. Mechanical testing found the combined bioactive treatment to synergistically increase the Young's modulus and ultimate tensile strength of the engineered fibrocartilages compared to controls, with values reaching the lower spectrum of those found in native tissues. Together, these data demonstrate that C-ABC and TGF-β1 interact to develop a denser collagen matrix better able to withstand tensile loading. This study highlights a way to optimize the tensile properties of engineered fibrocartilage using a biochemical and a biophysical agent together to create distinct fibrocartilages with functional properties mimicking those of native tissue. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Microwave spectroscopy of high-L Rydberg states of nickel

NASA Astrophysics Data System (ADS)

Lindsay, Mark D.; Keele, Julie A.; Woods, Shannon L.; Lundeen, Stephen R.

2010-03-01

High-L non-penetrating Rydberg levels of nickel display a fine structure pattern consisting of six levels for each value of L. This pattern was studied recently with the optical RESIS technique, determining initial values of the quadrupole moment and polarizabilities of the ^2D5/2 ground state of Ni^+ [1]. Measurements are now in progress using the microwave RESIS technique [2], which promises much more precise measurements of the fine structure and of the related core properties, including the permanent hexadecapole moment.[4pt] [1] Julie A. Keele, et. al., to be published, Phys. Rev. A[0pt] [2] M.E. Hanni, et. al., Phys. Rev. A 78, 062510 (2008)

Physiologic regulation of body energy storage

NASA Technical Reports Server (NTRS)

Pitts, G. C.

1978-01-01

Both new and published data (rats, mice, and human beings) on three parameters - fat mass, fat-free body mass (FFBM), and total body mass in some cases - are evaluated. Steady state values of the parameters are analyzed for changes in response to specific perturbing agents and for their frequency distributions. Temporal sequences of values on individuals are examined for evidence of regulatory responses. The results lead to the hypothesis that the FFBM is regulated, but probably not as a unit, and that mass of fat is regulated with a high priority near the range extremes but with a much lower priority in the mid-range. Properties and advantages of such a mechanism are discussed.

Influence of water immersion on the mechanical properties of fiber posts.

PubMed

Komada, Wataru; Inagaki, Tasuku; Ueda, Yoji; Omori, Satoshi; Hosaka, Keiichi; Tagami, Junji; Miura, Hiroyuki

2017-01-01

The purpose of this study was to evaluate the influence of water immersion on the mechanical properties of three kinds of glass fiber posts and the fracture resistance of structures using resin composites with glass fiber posts. Each post was divided into three groups; a control group and two water immersion groups (30 and 90 days). Flexural strength was determined by three-point bending test. Each structure was divided into two groups; a control group and a water immersion group for 30 days. The fracture strength of structures was determined by a static loading test. In the flexural strength, two kinds of post in water immersion groups showed lower values than control groups. In the fracture strength, two kinds of structures in water immersion group showed lower values than control groups. The prefabricated glass fiber posts and structures using resin composites with glass fiber posts were affected by water immersion. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Effects of replacing pork back fat with vegetable oils and rice bran fiber on the quality of reduced-fat frankfurters.

PubMed

Choi, Yun-Sang; Choi, Ji-Hun; Han, Doo-Jeong; Kim, Hack-Youn; Lee, Mi-Ai; Jeong, Jong-Youn; Chung, Hai-Jung; Kim, Cheon-Jei

2010-03-01

The effects of substituting olive, grape seed, corn, canola, or soybean oil and rice bran fiber on the chemical composition, cooking characteristics, fatty acid composition, and sensory properties of low-fat frankfurters were investigated. Ten percent of the total fat content of frankfurters with a total fat content of 30% (control) was partially replaced by one of the vegetable oils to reduce the pork fat content by 10%. The moisture and ash content of low-fat frankfurters with vegetable oil and rice bran fiber were all higher than the control (P<0.05). Low-fat frankfurters had reduced-fat content, energy values, cholesterol and trans-fat levels, and increased pH, cooking yield and TBA values compared to the controls (P<0.05). Low-fat frankfurters with reduced-fat content plus rice bran fiber had sensory properties similar to control frankfurters containing pork fat. Crown Copyright 2009. Published by Elsevier Ltd. All rights reserved.

The effects of modeling simplifications on craniofacial finite element models: the alveoli (tooth sockets) and periodontal ligaments.

PubMed

Wood, Sarah A; Strait, David S; Dumont, Elizabeth R; Ross, Callum F; Grosse, Ian R

2011-07-07

Several finite element models of a primate cranium were used to investigate the biomechanical effects of the tooth sockets and the material behavior of the periodontal ligament (PDL) on stress and strain patterns associated with feeding. For examining the effect of tooth sockets, the unloaded sockets were modeled as devoid of teeth and PDL, filled with teeth and PDLs, or simply filled with cortical bone. The third premolar on the left side of the cranium was loaded and the PDL was treated as an isotropic, linear elastic material using published values for Young's modulus and Poisson's ratio. The remaining models, along with one of the socket models, were used to determine the effect of the PDL's material behavior on stress and strain distributions under static premolar biting and dynamic tooth loading conditions. Two models (one static and the other dynamic) treated the PDL as cortical bone. The other two models treated it as a ligament with isotropic, linear elastic material properties. Two models treated the PDL as a ligament with hyperelastic properties, and the other two as a ligament with viscoelastic properties. Both behaviors were defined using published stress-strain data obtained from in vitro experiments on porcine ligament specimens. Von Mises stress and strain contour plots indicate that the effects of the sockets and PDL material behavior are local. Results from this study suggest that modeling the sockets and the PDL in finite element analyses of skulls is project dependent and can be ignored if values of stress and strain within the alveolar region are not required. Copyright © 2011 Elsevier Ltd. All rights reserved.

Effect of PLA films containing propolis ethanolic extract, cellulose nanoparticle and Ziziphora clinopodioides essential oil on chemical, microbial and sensory properties of minced beef.

PubMed

Shavisi, Nassim; Khanjari, Ali; Basti, Afshin Akhondzadeh; Misaghi, Ali; Shahbazi, Yasser

2017-02-01

This study was conducted to examine the effects of polylactic acid (PLA) film containing propolis ethanolic extract (PE), cellulose nanoparticle (CN) and Ziziphora clinopodioides essential oil (ZEO) on chemical, microbial and sensory properties of minced beef during storage at refrigerated temperature for 11days. The initial total volatile base nitrogen (TVB-N) was 8.2mg/100g and after 7days reached to 29.1mg/100g in control, while it was lower than 25mg/100g for treated samples. At the end of storage time in control samples peroxide value (PV) reached to 2.01meqperoxide/1000g lipid, while the values for the treated samples remained lower than 2meqperoxide/1000g lipid. Final microbial population decreased approximately 1-3logCFU/g in treated samples compared to control (P<0.05). Films containing 2% ZEO alone and in combination with different concentrations of PE and CN extended the shelf life of minced beef during storage in refrigerated condition for at least 11days without any unfavorable organoleptic properties. Copyright © 2016. Published by Elsevier Ltd.

"Stealing and Being Stolen From": Perpetration of Property Offenses and Property Victimization Among Homeless Youth--A Systematic Review

ERIC Educational Resources Information Center

Heerde, Jessica A.; Hemphill, Sheryl A.

2016-01-01

Homelessness is purportedly a predictor of property offending and property victimization, yet published studies examining this occurrence are scarce. This systematic review collates, summarizes, and appraises published studies reporting the rates of perpetration of property offenses and property victimization, and associations between homelessness…

Mechanical properties of components of the bonding interface in different regions of radicular dentin surfaces.

PubMed

Suzuki, Thaís Yumi Umeda; Gomes-Filho, João Eduardo; Gallego, Juno; Pavan, Sabrina; Dos Santos, Paulo Henrique; Fraga Briso, André Luiz

2015-01-01

The mechanical properties of the adhesive materials used in intraradicular treatments could vary according to the interaction between the restorative material and dentin substrate. An evaluation of these properties is essential to determine the success of the luting procedures performed on glass-fiber posts. The purpose of this study was to evaluate the mechanical properties of dentin adhesives, resin cements, and the dentin that underlies the bonding interface in different thirds of intraradicular dentin. Forty extracted, single-rooted human teeth were used in this study. After the endodontic treatment of the post spaces, the teeth were divided into 5 groups (n=8): Adper Single Bond 2 + RelyX ARC, Excite DSC + RelyX ARC, Adper SE Plus + RelyX ARC, RelyX Unicem, and Set. The hardness and elastic modulus values were measured at the adhesive interface in different thirds of the radicular dentin by using an ultramicrohardness tester. The data were subjected to 2-way ANOVA and the Fisher protected least significant difference test (α=.05). In the underlying dentin, the highest Martens hardness values were found in the apical region for all groups; the exceptions were the groups with the self-etching adhesive. In the adhesive layer, the highest Martens hardness values were obtained for the Adper SE Plus + RelyX ARC group; further, no statistical differences were found among the different regions for this group. RelyX ARC had the lowest Martens hardness and elastic modulus values in the apical regions when used with Adper Single Bond 2 and Adper SE Plus. No differences were found in the Martens hardness and elastic modulus values for the self-adhesive resin cement in the regions investigated. The mechanical properties of adhesive materials and the underlying dentin are influenced by the interaction between the two as well as by the depth of the analyzed intraradicular area. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Evaluation of Radiation Shielding Properties of the Polyvinyl Alcohol/Iron Oxide Polymer Composite

PubMed Central

Srinivasan, K.; Samuel, E. James Jabaseelan

2017-01-01

Context: Lead is the conventional shielding material against gamma/X-rays. It has some limitations such as toxic, high density, nonflexibility, and also bremsstrahlung production during electron interaction. It may affect the accuracy of radiotherapy outcome. Aims: To theoretically analyze the radiation shielding properties of flexible polyvinyl alcohol/iron oxide polymer composite with five different concentrations of magnetite over the energy range of 15 KeV–20 MeV. Subjects and Methods: Radiological properties were calculated based on the published literature. Attenuation coefficients of pure elements are generated with the help of WinXCOM database. Results: Effective atomic numbers and electron density are increased with the concentration of magnetite. On the other hand, the number of electrons per gram decreased. Mass attenuation coefficient (μ/ϼ) and linear attenuation coefficients (μ) are higher in the lower energy <100 KeV, and their values decreased when the energy increased. Computed tomography numbers (CT) show the significant variation between the concentrations in <60 KeV. Half-value layer and tenth-value layers are directly proportional to the energy and indirectly proportional to the concentration of magnetite. Transmission curve, relaxation length (ƛ), kinetic energy released in the matter, and elemental weight fraction are also calculated and the results are discussed. Conclusions: 0.5% of the magnetite gives superior shielding properties compared with other concentrations. It may be due to the presence of 0.3617% of Fe. Elemental weight fraction, atomic number, photon energy, and mass densities are the important parameters to understand the shielding behavior of any material. PMID:29296043

Intrinsic properties of limb bud cells can be differentially reset.

PubMed

Saiz-Lopez, Patricia; Chinnaiya, Kavitha; Towers, Matthew; Ros, Maria A

2017-02-01

An intrinsic timing mechanism specifies the positional values of the zeugopod (i.e. radius/ulna) and then autopod (i.e. wrist/digits) segments during limb development. Here, we have addressed whether this timing mechanism ensures that patterning events occur only once by grafting GFP-expressing autopod progenitor cells to the earlier host signalling environment of zeugopod progenitor cells. We show by detecting Hoxa13 expression that early and late autopod progenitors fated for the wrist and phalanges, respectively, both contribute to the entire host autopod, indicating that the autopod positional value is irreversibly determined. We provide evidence that Hoxa13 provides an autopod-specific positional value that correctly allocates cells into the autopod, most likely through the control of cell-surface properties as shown by cell-cell sorting analyses. However, we demonstrate that only the earlier autopod cells can adopt the host proliferation rate to permit normal morphogenesis. Therefore, our findings reveal that the ability of embryonic cells to differentially reset their intrinsic behaviours confers robustness to limb morphogenesis. We speculate that this plasticity could be maintained beyond embryogenesis in limbs with regenerative capacity. © 2017. Published by The Company of Biologists Ltd.

Lead toxicity thresholds in 17 Chinese soils based on substrate-induced nitrification assay.

PubMed

Li, Ji; Huang, Yizong; Hu, Ying; Jin, Shulan; Bao, Qiongli; Wang, Fei; Xiang, Meng; Xie, Huiting

2016-06-01

The influence of soil properties on toxicity threshold values for Pb toward soil microbial processes is poorly recognized. The impact of leaching on the Pb threshold has not been assessed systematically. Lead toxicity was screened in 17 Chinese soils using a substrate-induced nitrification (SIN) assay under both leached and unleached conditions. The effective concentration of added Pb causing 50% inhibition (EC50) ranged from 185 to >2515mg/kg soil for leached soil and 130 to >2490mg/kg soil for unleached soil. These results represented >13- and >19-fold variations among leached and unleached soils, respectively. Leaching significantly reduced Pb toxicity for 70% of both alkaline and acidic soils tested, with an average leaching factor of 3.0. Soil pH and CEC were the two most useful predictors of Pb toxicity in soils, explaining over 90% of variance in the unleached EC50 value. The relationships established in the present study predicted Pb toxicity within a factor of two of measured values. These relationships between Pb toxicity and soil properties could be used to establish site-specific guidance on Pb toxicity thresholds. Copyright © 2016. Published by Elsevier B.V.

Mushroom cultivation, processing and value added products: a patent based review.

PubMed

Singhal, Somya; Rasane, Prasad; Kaur, Sawinder; Garba, Umar; Singh, Jyoti; Raj, Nishant; Gupta, Neeru

2018-06-03

Edible mushrooms are an abundant source of carbohydrates, proteins, and multiple antioxidants and phytonutrients. This paper presents a general overview on the edible fungus describing the inventions made in the field of its cultivation, equipment and value added products. To understand and review the innovations and nutraceutical benefits of mushrooms as well as to develop interest regarding the edible mushrooms. Information provided in this review is based on the available research investigations and patents. Mushrooms are an edible source of a wide variety of antioxidants and phytonutrients with a number of nutraceutical properties including anti-tumor and anti-carcinogenic. Thus, several investigations are made for cultivation and improvement of the yield of mushrooms through improvisation of growth substrates and equipment used for mushroom processing. The mushroom has been processed into various products to increase its consumption, providing the health and nutritional benefit to mankind. This paper summarizes the cultivation practices of mushroom, its processing equipments, methods of preservation, value added based products, and its nutraceutical properties. The review also highlights the various scientific feats achieved in terms of patents and research publications promoting mushroom as a wholesome food. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Dehomogenized Elastic Properties of Heterogeneous Layered Materials in AFM Indentation Experiments.

PubMed

Lee, Jia-Jye; Rao, Satish; Kaushik, Gaurav; Azeloglu, Evren U; Costa, Kevin D

2018-06-05

Atomic force microscopy (AFM) is used to study mechanical properties of biological materials at submicron length scales. However, such samples are often structurally heterogeneous even at the local level, with different regions having distinct mechanical properties. Physical or chemical disruption can isolate individual structural elements but may alter the properties being measured. Therefore, to determine the micromechanical properties of intact heterogeneous multilayered samples indented by AFM, we propose the Hybrid Eshelby Decomposition (HED) analysis, which combines a modified homogenization theory and finite element modeling to extract layer-specific elastic moduli of composite structures from single indentations, utilizing knowledge of the component distribution to achieve solution uniqueness. Using finite element model-simulated indentation of layered samples with micron-scale thickness dimensions, biologically relevant elastic properties for incompressible soft tissues, and layer-specific heterogeneity of an order of magnitude or less, HED analysis recovered the prescribed modulus values typically within 10% error. Experimental validation using bilayer spin-coated polydimethylsiloxane samples also yielded self-consistent layer-specific modulus values whether arranged as stiff layer on soft substrate or soft layer on stiff substrate. We further examined a biophysical application by characterizing layer-specific microelastic properties of full-thickness mouse aortic wall tissue, demonstrating that the HED-extracted modulus of the tunica media was more than fivefold stiffer than the intima and not significantly different from direct indentation of exposed media tissue. Our results show that the elastic properties of surface and subsurface layers of microscale synthetic and biological samples can be simultaneously extracted from the composite material response to AFM indentation. HED analysis offers a robust approach to studying regional micromechanics of heterogeneous multilayered samples without destructively separating individual components before testing. Copyright © 2018 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Development of a Detailed Volumetric Finite Element Model of the Spine to Simulate Surgical Correction of Spinal Deformities

PubMed Central

Driscoll, Mark; Mac-Thiong, Jean-Marc; Labelle, Hubert; Parent, Stefan

2013-01-01

A large spectrum of medical devices exists; it aims to correct deformities associated with spinal disorders. The development of a detailed volumetric finite element model of the osteoligamentous spine would serve as a valuable tool to assess, compare, and optimize spinal devices. Thus the purpose of the study was to develop and initiate validation of a detailed osteoligamentous finite element model of the spine with simulated correction from spinal instrumentation. A finite element of the spine from T1 to L5 was developed using properties and geometry from the published literature and patient data. Spinal instrumentation, consisting of segmental translation of a scoliotic spine, was emulated. Postoperative patient and relevant published data of intervertebral disc stress, screw/vertebra pullout forces, and spinal profiles was used to evaluate the models validity. Intervertebral disc and vertebral reaction stresses respected published in vivo, ex vivo, and in silico values. Screw/vertebra reaction forces agreed with accepted pullout threshold values. Cobb angle measurements of spinal deformity following simulated surgical instrumentation corroborated with patient data. This computational biomechanical analysis validated a detailed volumetric spine model. Future studies seek to exploit the model to explore the performance of corrective spinal devices. PMID:23991426

Mineralogical, Microstructural and Thermal Characterization of Coal Fly Ash Produced from Kazakhstani Power Plants

NASA Astrophysics Data System (ADS)

Tauanov, Z.; Abylgazina, L.; Spitas, C.; Itskos, G.; Inglezakis, V.

2017-09-01

Coal fly ash (CFA) is a waste by-product of coal combustion. Kazakhstan has vast coal deposits and is major consumer of coal and hence produces huge amounts of CFA annually. The government aims to recycle and effectively utilize this waste by-product. Thus, a detailed study of the physical and chemical properties of material is required as the data available in literature is either outdated or not applicable for recently produced CFA samples. The full mineralogical, microstructural and thermal characterization of three types of coal fly ash (CFA) produced in two large Kazakhstani power plants is reported in this work. The properties of CFAs were compared between samples as well as with published values.

Visible and infrared optical properties of stacked cone graphite microtubes.

PubMed

Bruce, Charles W; Alyones, Sharhabeel

2012-06-01

The absorptive and scattering optical properties of heat-treated, vapor-grown, graphite microtubes consisting of nanotubes in a "stacked cone" configuration were investigated through the visible and infrared wavelengths using photoacoustic and other spectrometric techniques. However, computations of these properties involved uncertainties that were not easily resolved; the appropriate dielectric coefficients were presumed to be a combination of the published values for the distinct orientations of graphite, but the correct proportions are not evident and none of the reasonable choices produced satisfactory agreement (within the measurement limits of error). Since both of the primary components of the extinction were measured, the appropriate computational codes were employed in reverse to compute the dielectric coefficients for the graphite microtubes. Differences, primarily for the imaginary index, are most distinct for visible and near infrared wavelengths; in this wavelength region, the imaginary index falls progressively to less than half that for the computed mixture.

What is the enduring value of research publications in clinical epilepsy? An assessment of papers published in 1981, 1991, and 2001.

PubMed

Gregoris, Nattanit; Shorvon, Simon

2013-09-01

There has been a rapid expansion in the number of research papers published on clinical epilepsy topics and the number of journals in the medical field. In this expanding publishing environment, the question arises as to how much of the published medical literature has 'enduring value' in terms of advancing knowledge in any significant way. We developed a methodology to assess the enduring value of papers published in the field of clinical epilepsy and established its internal validity. We studied 300 research papers published in 1981, 1991, and 2001 (100 in each year) and assessed their enduring value in four domains: citations in the last year, citations in the last 10years, citations in the standard epilepsy textbook, and a subjective assessment by an experienced epileptologist. Of the 300 papers, 214 (71%) were categorized as having 'no enduring value', and only 11 (4%) were identified as having 'high enduring value'. The 'high enduring value' papers could generally be identified immediately on publication, by high initial citation values, and were also more likely to be published in journals with a high impact factor. The commonest characteristics of a paper with no enduring value were that they reported research that was inherently unimportant (55.6%), not novel (38.8%), or had significant methodological flaws (22.0%). Although there are other reasons for publishing papers, the fact that the great majority of published papers lack enduring value in terms of advancing knowledge should be a concern to the medical and scientific community. Copyright © 2013 Elsevier Inc. All rights reserved.

Shedding light on the variability of optical skin properties: finding a path towards more accurate prediction of light propagation in human cutaneous compartments

PubMed Central

Mignon, C.; Tobin, D. J.; Zeitouny, M.; Uzunbajakava, N. E.

2018-01-01

Finding a path towards a more accurate prediction of light propagation in human skin remains an aspiration of biomedical scientists working on cutaneous applications both for diagnostic and therapeutic reasons. The objective of this study was to investigate variability of the optical properties of human skin compartments reported in literature, to explore the underlying rational of this variability and to propose a dataset of values, to better represent an in vivo case and recommend a solution towards a more accurate prediction of light propagation through cutaneous compartments. To achieve this, we undertook a novel, logical yet simple approach. We first reviewed scientific articles published between 1981 and 2013 that reported on skin optical properties, to reveal the spread in the reported quantitative values. We found variations of up to 100-fold. Then we extracted the most trust-worthy datasets guided by a rule that the spectral properties should reflect the specific biochemical composition of each of the skin layers. This resulted in the narrowing of the spread in the calculated photon densities to 6-fold. We conclude with a recommendation to use the identified most robust datasets when estimating light propagation in human skin using Monte Carlo simulations. Alternatively, otherwise follow our proposed strategy to screen any new datasets to determine their biological relevance. PMID:29552418

pH-dependent surface charging and points of zero charge. IV. Update and new approach.

PubMed

Kosmulski, Marek

2009-09-15

The recently published points of zero charge (PZC) and isoelectric points (IEPs) of various materials are compiled to update the previous compilation [M. Kosmulski, Surface Charging and Points of Zero Charge, CRC Press, Boca Raton, FL, 2009]. Unlike in previous compilations by the same author [Chemical Properties of Material Surfaces, Dekker, New York, 2001; J. Colloid Interface Sci. 253 (2002) 77; J. Colloid Interface Sci. 275 (2004) 214; J. Colloid Interface Sci. 298 (2006) 730], the materials are sorted not only by the chemical formula, but also by specific product, that is, by brand name (commercially available materials), and by recipe (home-synthesized materials). This new approach indicated that the relatively consistent PZC/IEP reported in the literature for materials having the same chemical formula are due to biased choice of specimens to be studied. Specimens which have PZC/IEP close to the "recommended" value are selected more often than other specimens (PZC/IEP not reported before or PZC/IEP reported, but different from the "recommended" value). Thus, the previously published PZC/IEP act as a self-fulfilling prophecy.

Physical properties of sugar cookies containing chia-oat composites.

PubMed

Inglett, George E; Chen, Diejun; Liu, Sean

2014-12-01

Omega-3 fatty acids of chia seeds (Salvia hispanica L.) and soluble β-glucan of oat products are known for lowering blood cholesterol and preventing coronary heart disease. Nutrim, oat bran concentrate (OBC), and whole oat flour (WOF) were composited with finely ground chia, and used in cookies at 20% replacement of wheat flour for improved nutritional and physical quality. The objective was to evaluate physical properties of chia-oat composites, dough, and cookies. These composites had improved water-holding capacities compared to the starting materials. The geometrical properties and texture properties of the cookies were not greatly influenced by a 20% flour replacement using chia-OBC or chia-WOF composites. There was a decrease in the cookie diameter, and increases in the height of cookies and dough hardness using 20% Chia- Nutrim composite. These fine-particle chia-oat composites were prepared by a feasible procedure for improved nutritional value and physical properties of foods. The cookies containing chia-oat composites can be considered a health-promoting functional food. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

Growth-dependent effects of dietary protein concentration and quality on the biomechanical properties of the diaphyseal rat femur.

PubMed

Alippi, Rosa M; Picasso, Emilio; Huygens, Patricia; Bozzini, Carlos E; Bozzini, Clarisa

2012-01-01

This study compares the effects of feeding growing rats with increasing concentrations of casein (C) and wheat gluten (G), proteins that show different biological qualities, on the morphometrical and biomechanical properties of the femoral diaphysis. Female rats were fed with one of ten diets containing different concentrations (5-30%) of C and G between the 30th and 90th days of life (Control=C-20%). Biomechanical structural properties of the right femur middiaphysis were estimated using a 3-point bending mechanical test with calculation of some indicators of bone material properties. Body weight and length were affected by treatments, values being highest in rats fed the C-20% diet. G diets affected negatively both parameters. Changes in cross-sectional geometry (mid-diaphyseal cross-sectional and cortical areas, femoral volume, and rectangular moment of inertia) were positively related to the C content of the diet, while they were severely and negatively affected by G diets. Similar behaviors were observed in the bone structural properties (fracture load, yielding load, diaphyseal stiffness and elastic energy absorption). When values of strength and stiffness were normalized for body weight, the differences disappeared. The bone material quality indicators (elastic modulus, yielding stress, elastic energy absorption/volume) did not differ significantly among all studied groups. Femoral calcium concentration in ashes was not significantly different among groups. The clear differences in strength and stiffness of bone beams induced by dietary protein concentration and quality seemed to be the result of an induced subnormal gain in bone structural properties as a consequence of a correlative subnormal gain in bone growth and mass, yet not in bone material properties. Copyright © 2011 SEEN. Published by Elsevier Espana. All rights reserved.

High Density Polyethylene Composites Reinforced with Hybrid Inorganic Fillers: Morphology, Mechanical and Thermal Expansion Performance

PubMed Central

Huang, Runzhou; Xu, Xinwu; Lee, Sunyoung; Zhang, Yang; Kim, Birm-June; Wu, Qinglin

2013-01-01

The effect of individual and combined talc and glass fibers (GFs) on mechanical and thermal expansion performance of the filled high density polyethylene (HDPE) composites was studied. Several published models were adapted to fit the measured tensile modulus and strength of various composite systems. It was shown that the use of silane-modified GFs had a much larger effect in improving mechanical properties and in reducing linear coefficient of thermal expansion (LCTE) values of filled composites, compared with the use of un-modified talc particles due to enhanced bonding to the matrix, larger aspect ratio, and fiber alignment for GFs. Mechanical properties and LCTE values of composites with combined talc and GF fillers varied with talc and GF ratio at a given total filler loading level. The use of a larger portion of GFs in the mix can lead to better composite performance, while the use of talc can help lower the composite costs and increase its recyclability. The use of 30 wt % combined filler seems necessary to control LCTE values of filled HDPE in the data value range generally reported for commercial wood plastic composites. Tensile modulus for talc-filled composite can be predicted with rule of mixture, while a PPA-based model can be used to predict the modulus and strength of GF-filled composites. PMID:28788322

A unified relation for the solid-liquid interface free energy of pure FCC, BCC, and HCP metals.

PubMed

Wilson, S R; Mendelev, M I

2016-04-14

We study correlations between the solid-liquid interface (SLI) free energy and bulk material properties (melting temperature, latent heat, and liquid structure) through the determination of SLI free energies for bcc and hcp metals from molecular dynamics (MD) simulation. Values obtained for the bcc metals in this study were compared to values predicted by the Turnbull, Laird, and Ewing relations on the basis of previously published MD simulation data. We found that of these three empirical relations, the Ewing relation better describes the MD simulation data. Moreover, whereas the original Ewing relation contains two constants for a particular crystal structure, we found that the first coefficient in the Ewing relation does not depend on crystal structure, taking a common value for all three phases, at least for the class of the systems described by embedded-atom method potentials (which are considered to provide a reasonable approximation for metals).

A unified relation for the solid-liquid interface free energy of pure FCC, BCC, and HCP metals

NASA Astrophysics Data System (ADS)

Wilson, S. R.; Mendelev, M. I.

2016-04-01

We study correlations between the solid-liquid interface (SLI) free energy and bulk material properties (melting temperature, latent heat, and liquid structure) through the determination of SLI free energies for bcc and hcp metals from molecular dynamics (MD) simulation. Values obtained for the bcc metals in this study were compared to values predicted by the Turnbull, Laird, and Ewing relations on the basis of previously published MD simulation data. We found that of these three empirical relations, the Ewing relation better describes the MD simulation data. Moreover, whereas the original Ewing relation contains two constants for a particular crystal structure, we found that the first coefficient in the Ewing relation does not depend on crystal structure, taking a common value for all three phases, at least for the class of the systems described by embedded-atom method potentials (which are considered to provide a reasonable approximation for metals).

A chitosan-based coating with or without clove oil extends the shelf life of cooked pork sausages in refrigerated storage.

PubMed

Lekjing, Somwang

2016-01-01

Chitosan coatings, with and without clove oil, were investigated for effects on quality and shelf life of cooked pork sausages stored at a refrigerated temperature (4±2°C). The various treatments of cooked pork sausages were: untreated (control), coating with 2% chitosan (CS), and coating with a mixture having 2% chitosan and 1.5% clove oil (CS+CO). Various microbiological, physical, chemical and sensory properties were monitored over 25 days of storage. The total viable count, the psychrotrophic bacteria count, the L* value, peroxide value and the thiobarbituric acid reactive substances increased, while the a* value, the b* value, the pH and the sensory scores decreased with storage time, across all treatments. However, these changes were slowest with the CS+CO treatment. Based on sensory evaluation and microbiological quality, the shelf lives were 14 days for control, 20 days for CS, and 20 days for CS+CO treated samples, under refrigerated storage. Copyright © 2015. Published by Elsevier Ltd.

Experimentally valid predictions of muscle force and EMG in models of motor-unit function are most sensitive to neural properties.

PubMed

Keenan, Kevin G; Valero-Cuevas, Francisco J

2007-09-01

Computational models of motor-unit populations are the objective implementations of the hypothesized mechanisms by which neural and muscle properties give rise to electromyograms (EMGs) and force. However, the variability/uncertainty of the parameters used in these models--and how they affect predictions--confounds assessing these hypothesized mechanisms. We perform a large-scale computational sensitivity analysis on the state-of-the-art computational model of surface EMG, force, and force variability by combining a comprehensive review of published experimental data with Monte Carlo simulations. To exhaustively explore model performance and robustness, we ran numerous iterative simulations each using a random set of values for nine commonly measured motor neuron and muscle parameters. Parameter values were sampled across their reported experimental ranges. Convergence after 439 simulations found that only 3 simulations met our two fitness criteria: approximating the well-established experimental relations for the scaling of EMG amplitude and force variability with mean force. An additional 424 simulations preferentially sampling the neighborhood of those 3 valid simulations converged to reveal 65 additional sets of parameter values for which the model predictions approximate the experimentally known relations. We find the model is not sensitive to muscle properties but very sensitive to several motor neuron properties--especially peak discharge rates and recruitment ranges. Therefore to advance our understanding of EMG and muscle force, it is critical to evaluate the hypothesized neural mechanisms as implemented in today's state-of-the-art models of motor unit function. We discuss experimental and analytical avenues to do so as well as new features that may be added in future implementations of motor-unit models to improve their experimental validity.

Use of SkinFibrometer® to measure skin elasticity and its correlation with Cutometer® and DUB® Skinscanner.

PubMed

Kim, M A; Kim, E J; Lee, H K

2018-02-06

Skin elasticity is an important indicator of skin aging. The aim of this study was to demonstrate that the SkinFibrometer ® is appropriate for measuring skin biomechanical properties, and to correlate it with elasticity parameters measured using the Cutometer ® and with dermis structural properties measured using DUB ® Skinscanner. Twenty-one individuals participated in this study. The skin of the cheek, around the eye, and the volar forearm were evaluated. To analyze correlations of elasticity parameters, the induration value against the indenter pressure of SkinFibrometer ® and R, Q parameters of Cutometer ® were compared. Dermal echogenicity using DUB ® Skinscanner was compared with the induration value of SkinFibrometer ® . The younger age group showed more firm and elastic skin properties compared to the older age group, and the elasticity values of the volar forearm were significantly higher than those of the cheek and around the eye region. Even though the measuring principle is different, both SkinFibrometer ® and Cutometer ® demonstrated the same trends of skin elasticity differences according to age and anatomical regions. There were significant correlations between the induration value of SkinFibrometer ® , representing skin firmness, and R0, Q0 and R2, R5, R7, Q1, Q2 of Cutometer ® , which represent skin firmness and resilience, respectively (P < .01). In addition, dermal echogenicity positively correlated with skin firmness determined by SkinFibrometer ® (P < .01). We identified correlations between skin elasticity parameters evaluated by two different methods of suction and indentation, and demonstrated that the SkinFibrometer ® is an objective, non-invasive evaluation tool for skin stiffness and elasticity. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Optimised analytical models of the dielectric properties of biological tissue.

PubMed

Salahuddin, Saqib; Porter, Emily; Krewer, Finn; O' Halloran, Martin

2017-05-01

The interaction of electromagnetic fields with the human body is quantified by the dielectric properties of biological tissues. These properties are incorporated into complex numerical simulations using parametric models such as Debye and Cole-Cole, for the computational investigation of electromagnetic wave propagation within the body. These parameters can be acquired through a variety of optimisation algorithms to achieve an accurate fit to measured data sets. A number of different optimisation techniques have been proposed, but these are often limited by the requirement for initial value estimations or by the large overall error (often up to several percentage points). In this work, a novel two-stage genetic algorithm proposed by the authors is applied to optimise the multi-pole Debye parameters for 54 types of human tissues. The performance of the two-stage genetic algorithm has been examined through a comparison with five other existing algorithms. The experimental results demonstrate that the two-stage genetic algorithm produces an accurate fit to a range of experimental data and efficiently out-performs all other optimisation algorithms under consideration. Accurate values of the three-pole Debye models for 54 types of human tissues, over 500 MHz to 20 GHz, are also presented for reference. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Deoxypyrimidine kinases of herpes simplex viruses types 1 and 2: comparison of serological and structural properties.

PubMed

Thouless, M E; Wildy, P

1975-02-01

The kinetics of formation, the stability at 40 degrees C and the serological properties of thymidine kinase and deoxycytidine kinase activities induced by herpes simplex virus have been examined. The results are consistent with the hypothesis that both activities are carried on the same molecule-a deoxypyrimidine kinase. Mutants deficient in deoxypyrimidine kinase have been used to produce, by absorption of general antisera, deoxypyrimidine kinase-specific antisera. Using immunoprecipitation and SDS-polyacrylamide gel electrophoresis, only one size of polypeptide (mol. wt. 42400 plus or minus 200) has been found, constituting the type 2 enzyme. This is close to published values for the type i enzyme but co-electrophoresis demonstrated that the polypeptide of the type i enzyme was slightly bigger.

Evaluation of different water-washing treatments effects on wheat straw combustion properties.

PubMed

Ma, Qiulin; Han, Lujia; Huang, Guangqun

2017-12-01

A series of experiments was conducted to explore the effects of various water-washing solid-liquid ratios (1:50 and 1:10) and the stirring on wheat straw (WS) combustion properties. Comparing different solid-liquid ratio groups, a 16% increment in the higher heating value was obtained for 1:50 groups and only 5% for 1:10 groups relative to the raw material. Moreover, energy was lost 4-26 times greater in 1:10 groups than 1:50 groups. While water-washing reduced the comprehensive combustibility index by 14.89%-32.09%, the index values of washed WS were all higher than 2, indicating good combustion performance. The combustion activation energy of four washed WS were 175, 172, 186, and 176kJ/mol, which were all higher than the 160kJ/mol of WS. The fouling/slagging propensity of washed WS reduced to a lower possibility compared to medium of untreated WS. Overall, the recommended condition for washing WS before combustion is 1:50 ratio without stirring. Copyright © 2017. Published by Elsevier Ltd.

Variable-focus microscopy and UV surface dissolution imaging as complementary techniques in intrinsic dissolution rate determination.

PubMed

Ward, Adam; Walton, Karl; Box, Karl; Østergaard, Jesper; Gillie, Lisa J; Conway, Barbara R; Asare-Addo, Kofi

2017-09-15

This work reports a novel approach to the assessment of the surface properties of compacts used in Surface Dissolution Imaging (SDI). SDI is useful for determining intrinsic dissolution rate (IDR), an important parameter in early stage drug development. Surface topography, post-compaction and post-SDI run, have been measured using a non-contact, optical, three-dimensional microscope based on focus variation, the Alicona Infinite Focus Microscope, with the aim of correlating the IDRs to the surface properties. Ibuprofen (IBU) was used as a model poorly-soluble drug. DSC and XRD were used to monitor possible polymorphic changes that may have occurred post-compaction and post-SDI run. IBUs IDR decreased from 0.033mg/min/cm 2 to 0.022mg/min/cm 2 from 10 to 20min, respectively, during the experiment. XRD and DSC showed no form changes during the SDI run. The surface topography images showed that a distinct imprint was embossed on the surfaces of some compacts which could affect IDRs. Surface parameter values were associated with the SDI experiments which showed strong correlations with the IDR values. The variable-focus microscope can be used as a complimentary tool in the determination of IDR values from the SDI. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Study of a novel ultrasonically triggered drug vehicle with magnetic resonance properties.

PubMed

Liu, Tse-Ying; Huang, Hsin-Hui; Chen, Yen-Ju; Chen, Yu-Jen

2011-02-01

We developed a novel ultrasonically triggered drug vehicle with magnetic resonance (MR) properties by encapsulating superparamagnetic iron oxide (SPIO) nanoparticles in hydroxyapatite (HA)-coated liposomes. The effects of HA coating on the background leakage, ultrasound response and MR signal were investigated. HA coating of liposomes significantly reduced the background leakage of liposome. It also enhanced their sensitivity to ultrasound regardless of HA thickness or ultrasound frequency, even under sonication conditions of high frequency (1 and 3 MHz) and low power density (0.2-0.4 Wcm(-2)) used for diagnosis. However, it was found that the ultrasonically triggered vehicle could exhibit T(2) contrast in MR images by encapsulating SPIO. However, HA coating reduced the r(2) value of SPIO encapsulated in liposomes, but had no significant effect on the r(2)(∗) value, implying that MR images of HA-coated liposomes encapsulating SPIO could be probed by the T(2)(∗) signal. Most importantly, the r(2)(∗)-r(2) value of HA-coated liposomes encapsulating SPIO decreased after sonication, suggesting that the proposed vehicle could be used not only as a MR-guided drug vehicle capable of ultrasonically triggered release but also as a MR reporter to probe ultrasonic triggering. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Metabolite diffusion up to very high b in the mouse brain in vivo: Revisiting the potential correlation between relaxation and diffusion properties.

PubMed

Ligneul, Clémence; Palombo, Marco; Valette, Julien

2017-04-01

To assess the potential correlation between metabolites diffusion and relaxation in the mouse brain, which is of importance for interpreting and modeling metabolite diffusion based on pure geometry, irrespective of relaxation properties (multicompartmental relaxation or surface relaxivity). A new diffusion-weighted magnetic resonance spectroscopy sequence is introduced, dubbed "STE-LASER," which presents several nice properties, in particular the absence of cross-terms with selection gradients and a very clean localization. Metabolite diffusion is then measured in a large voxel in the mouse brain at 11.7 Tesla using a cryoprobe, resulting in excellent signal-to-noise ratio, up to very high b-values under different echo time, mixing time, and diffusion time combinations. Our results suggest that the correlation between relaxation and diffusion properties is extremely small or even nonexistent for metabolites in the mouse brain. The present work strongly supports the interpretation and modeling of metabolite diffusion primarily based on geometry, irrespective of relaxation properties, at least under current experimental conditions. Magn Reson Med 77:1390-1398, 2017. © 2016 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution-NonCommercial-NoDerivs License, which permits use and distribution in any medium, provided the original work is properly cited, the use is non-commercial and no modifications or adaptations are made. © 2016 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine.

Low thermal dependence of the contractile properties of a wing muscle in the bat Carollia perspicillata.

PubMed

Rummel, Andrea D; Swartz, Sharon M; Marsh, Richard L

2018-05-29

Temperature affects contractile rate properties in muscle, which may affect locomotor performance. Endotherms are known to maintain high core body temperatures, but temperatures in the periphery of the body can fluctuate. Such a phenomenon occurs in bats, whose wing musculature is relatively poorly insulated, resulting in substantially depressed temperatures in the distal wing. We examined a wing muscle in the small-bodied tropical bat Carollia perspicillata and a hindlimb muscle in the laboratory mouse at 5°C intervals from 22 to 42°C to determine the thermal dependence of the contractile properties of both muscles. We found that the bat ECRL had low thermal dependence from near body temperature to 10°C lower, with Q 10 values of less than 1.5 for relaxation from contraction and shortening velocities in that interval, and with no significant difference in some rate properties in the interval between 32 and 37°C. In contrast, for all temperature intervals below 37°C, Q 10 values for the mouse EDL were 1.5 or higher, and rate properties differed significantly across successive temperature intervals from 37 to 22°C. An ANCOVA analysis found that the thermal dependencies of all measured isometric and isotonic rate processes were significantly different between the bat and mouse muscles. The relatively low thermal dependence of the bat muscle likely represents a downward shift of its optimal temperature and may be functionally significant in light of the variable operating temperatures of bat wing muscles. © 2018. Published by The Company of Biologists Ltd.

41 CFR 105-60.201 - Published information and rules.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false Published information and rules. 105-60.201 Section 105-60.201 Public Contracts and Property Management Federal Property Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional Offices-General Services...

41 CFR 105-60.201 - Published information and rules.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false Published information and rules. 105-60.201 Section 105-60.201 Public Contracts and Property Management Federal Property Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional Offices-General Services...

41 CFR 105-60.201 - Published information and rules.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false Published information and rules. 105-60.201 Section 105-60.201 Public Contracts and Property Management Federal Property Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional Offices-General Services...

41 CFR 105-60.201 - Published information and rules.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false Published information and rules. 105-60.201 Section 105-60.201 Public Contracts and Property Management Federal Property Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional Offices-General Services...

The investigation of the skin characteristics of males focusing on gender differences, skin perception, and skin care habits.

PubMed

Mizukoshi, Koji; Akamatsu, Hisashi

2013-05-01

Various studies have examined the properties of male skin. However, because these studies mostly involved simple measurement with non-invasive devices, a lack of understanding of the properties of male skin remains. In this study, we focused and investigated not only on simple instrumental measurements but also on gender differences and men's subjective perceptions of skin and daily skin care habits. Barrier function depends on corneocyte maturation level as well as sebum amount. Irrespective of the skin type, a high percentage of male subjects perceived a 'tacky feeling'. However, the percentage of men perceiving a 'shiny feeling' differed by skin type. Furthermore, there was a relationship between skin care habits and skin function. Men who did not perform a daily skincare regimen demonstrated a significantly higher sebum amount and transepidermal water loss value than those who did perform a daily skincare regimen. The results of this study indicate that male skin has two specific characteristics: impaired barrier function because of the excess amount of sebum and a lack of an appropriate skin care regimen because of the 'tacky feeling' caused by excess sebum. © 2012 John Wiley & Sons A/S. Published by Blackwell Publishing Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hardin, Ernest; Hadgu, Teklu; Greenberg, Harris

This report is one follow-on to a study of reference geologic disposal design concepts (Hardin et al. 2011a). Based on an analysis of maximum temperatures, that study concluded that certain disposal concepts would require extended decay storage prior to emplacement, or the use of small waste packages, or both. The study used nominal values for thermal properties of host geologic media and engineered materials, demonstrating the need for uncertainty analysis to support the conclusions. This report is a first step that identifies the input parameters of the maximum temperature calculation, surveys published data on measured values, uses an analytical approachmore » to determine which parameters are most important, and performs an example sensitivity analysis. Using results from this first step, temperature calculations planned for FY12 can focus on only the important parameters, and can use the uncertainty ranges reported here. The survey of published information on thermal properties of geologic media and engineered materials, is intended to be sufficient for use in generic calculations to evaluate the feasibility of reference disposal concepts. A full compendium of literature data is beyond the scope of this report. The term “uncertainty” is used here to represent both measurement uncertainty and spatial variability, or variability across host geologic units. For the most important parameters (e.g., buffer thermal conductivity) the extent of literature data surveyed samples these different forms of uncertainty and variability. Finally, this report is intended to be one chapter or section of a larger FY12 deliverable summarizing all the work on design concepts and thermal load management for geologic disposal (M3FT-12SN0804032, due 15Aug2012).« less

Acoustic properties of reticulated plastic foams

NASA Astrophysics Data System (ADS)

Cummings, A.; Beadle, S. P.

1994-08-01

Some general aspects of sound propagation in rigid porous media are discussed, particularly with reference to the use of a single - dimensionless - frequency parameter and the role of this, in the light of the possibility of varying gas properties, is examined. Steady flow resistance coefficients of porous media are also considered, and simple scaling relationships between these coefficients and `system parameters' are derived. The results of a series of measurements of the bulk acoustic properties of 12 geometrically similar, fully reticulated, polyurethane foams are presented, and empirical curve-fitting coefficients are found; the curve-fitting formulae are valid within the experimental range of values of the frequency parameter. Comparison is made between the measured data and an alternative, fairly recently published, semi-empirical set of formulae. Measurements of the steady flow-resistive coefficients are also given and both the acoustical and flow-resistive data are shown to be consistent with theoretical ideas. The acoustical and flow-resistive data should be of use in predicting the acoustic bulk properties of open-celled foams of types similar to those used in the experimental tests.

Estimating thermal maturity in the Eagle Ford Shale petroleum system using gas gravity data

USGS Publications Warehouse

Birdwell, Justin E.; Kinney, Scott A.

2017-01-01

Basin-wide datasets that provide information on the geochemical properties of petroleum systems, such as source rock quality, product composition, and thermal maturity, are often difficult to come by or assemble from publically available data. When published studies are available and include these kinds of properties, they generally have few sampling locations and limited numbers and types of analyses. Therefore, production-related data and engineering parameters can provide useful proxies for geochemical properties that are often widely available across a play and in some states are reported in publically available or commercial databases. Gas-oil ratios (GOR) can be calculated from instantaneous or cumulative production data and can be related to the source rock geochemical properties like kerogen type (Lewan and Henry, 1999) and thermal maturity (Tian et al., 2013; U.S. Energy Information Administration [EIA], 2014). Oil density or specific gravity (SG), often reported in American Petroleum Institute units (°API = 141.5 /SG – 131.5), can also provide information on source rock thermal maturity, particularly when combined with GOR values in unconventional petroleum systems (Nesheim, 2017).

On the mechanical properties of tooth enamel under spherical indentation.

PubMed

Chai, Herzl

2014-11-01

The mechanical properties of tooth enamel generally exhibit large variations, which reflect its structural and material complexity. Some key properties were evaluated under localized contact, simulating actual functioning conditions. Prominent cusps of extracted human molar teeth were polished down ~0.7 mm below the cusp tip and indented by tungsten carbide balls. The internal damage was assessed after unloading from longitudinal or transverse sections. The ultimate tensile stress (UTS) was determined using a novel bilayer specimen. The damage is characterized by penny-like radial cracks driven by hoop stresses and cylindrical cracks driven along protein-rich interrod materials by shear stresses. Shallow cone cracks typical of homogeneous materials which may cause rapid tooth wear under repeat contact are thus avoided. The mean stress vs. indentation strain curve is highly nonlinear, attributable to plastic shearing of protein between and within enamel rods. This curve is also affected by damage, especially radial cracks, the onset of which depends on ball radius. Several material properties were extracted from the tests, including shear strain at the onset of ring cracks γ(F) (=0.14), UTS (=119 MPa), toughness K(C) (=0.94 MPa m(1/2)), a crack propagation law and a constitutive response determined by trial and error with the aid of a finite-element analysis. These quantities, which are only slightly sensitive to anatomical location within the enamel region tested, facilitate a quantitative assessment of crown failure. Causes for variations in published UTS and K(C) values are discussed. Copyright © 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Public values for integration in natural disaster management and planning: A case study from Victoria, Australia.

PubMed

Rawluk, Andrea; Ford, Rebecca M; Neolaka, Fendi L; Williams, Kathryn J

2017-01-01

Values can be useful for identifying what is important to individuals and communities, yet there is currently not a coherent way to conceptualize, identify, and organize the breadth of values that can be affected by a natural disaster. This research proposes a conceptual framework for how to conceptualize, identify, and organize values, and proposes a concrete, tangible value called the valued entity. The framework is applied in two studies of bushfire in Victoria, Australia: 112 submissions from individuals to the 2009 Victorian Bushfires Royal Commission and interviews with 30 members of the public in bushfire risk landscapes. Our findings suggest that: what people value ranges from abstract to concrete; prevalent abstract values include benevolence and universalism; prevalent mid-level valued attributes include natural attributes of landscapes and human life and welfare; prevalent valued entities are people and properties close to the person. Comparison between the two studies suggests people with more recent experience with bushfire refer less to the importance of natural places and natural attributes. The conceptual framework can act as a boundary object to facilitate researchers and policy-makers understanding the breadth of values affected by natural disaster events and management actions and how governance can better consider values at different scales. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

A Quantitative Comparison of the Behavior of Human Ventricular Cardiac Electrophysiology Models in Tissue

PubMed Central

Elshrif, Mohamed M.; Cherry, Elizabeth M.

2014-01-01

Numerical integration of mathematical models of heart cell electrophysiology provides an important computational tool for studying cardiac arrhythmias, but the abundance of available models complicates selecting an appropriate model. We study the behavior of two recently published models of human ventricular action potentials, the Grandi-Pasqualini-Bers (GPB) and the O'Hara-Virág-Varró-Rudy (OVVR) models, and compare the results with four previously published models and with available experimental and clinical data. We find the shapes and durations of action potentials and calcium transients differ between the GPB and OVVR models, as do the magnitudes and rate-dependent properties of transmembrane currents and the calcium transient. Differences also occur in the steady-state and S1–S2 action potential duration and conduction velocity restitution curves, including a maximum conduction velocity for the OVVR model roughly half that of the GPB model and well below clinical values. Between single cells and tissue, both models exhibit differences in properties, including maximum upstroke velocity, action potential amplitude, and minimum diastolic interval. Compared to experimental data, action potential durations for the GPB and OVVR models agree fairly well (although OVVR epicardial action potentials are shorter), but maximum slopes of steady-state restitution curves are smaller. Although studies show alternans in normal hearts, it occurs only in the OVVR model, and only for a narrow range of cycle lengths. We find initiated spiral waves do not progress to sustained breakup for either model. The dominant spiral wave period of the GPB model falls within clinically relevant values for ventricular tachycardia (VT), but for the OVVR model, the dominant period is longer than periods associated with VT. Our results should facilitate choosing a model to match properties of interest in human cardiac tissue and to replicate arrhythmia behavior more closely. Furthermore, by indicating areas where existing models disagree, our findings suggest avenues for further experimental work. PMID:24416228

41 CFR 105-60.202 - Published materials available for sale to the public.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false Published materials available for sale to the public. 105-60.202 Section 105-60.202 Public Contracts and Property Management Federal Property Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional...

41 CFR 105-60.202 - Published materials available for sale to the public.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false Published materials available for sale to the public. 105-60.202 Section 105-60.202 Public Contracts and Property Management Federal Property Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional...

41 CFR 105-60.202 - Published materials available for sale to the public.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false Published materials available for sale to the public. 105-60.202 Section 105-60.202 Public Contracts and Property Management Federal Property Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional...

41 CFR 105-60.202 - Published materials available for sale to the public.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false Published materials available for sale to the public. 105-60.202 Section 105-60.202 Public Contracts and Property Management Federal Property Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional...

Physicochemical properties of mucus and their impact on transmucosal drug delivery.

PubMed

Leal, Jasmim; Smyth, Hugh D C; Ghosh, Debadyuti

2017-10-30

Mucus is a selective barrier to particles and molecules, preventing penetration to the epithelial surface of mucosal tissues. Significant advances in transmucosal drug delivery have recently been made and have emphasized that an understanding of the basic structure, viscoelastic properties, and interactions of mucus is of great value in the design of efficient drug delivery systems. Mucins, the primary non-aqueous component of mucus, are polymers carrying a complex and heterogeneous structure with domains that undergo a variety of molecular interactions, such as hydrophilic/hydrophobic, hydrogen bonds and electrostatic interactions. These properties are directly relevant to the numerous mucin-associated diseases, as well as delivering drugs across the mucus barrier. Therefore, in this review we discuss regional differences in mucus composition, mucus physicochemical properties, such as pore size, viscoelasticity, pH, and ionic strength. These factors are also discussed with respect to changes in mucus properties as a function of disease state. Collectively, the review seeks to provide a state of the art roadmap for researchers who must contend with this critical barrier to drug delivery. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Regional variation of white matter development in the cat brain revealed by ex vivo diffusion MR tractography.

PubMed

Dai, Guangping; Das, Avilash; Hayashi, Emiko; Chen, Qin; Takahashi, Emi

2016-11-01

Three-dimensional reconstruction of developing fiber pathways is essential to assessing the developmental course of fiber pathways in the whole brain. We applied diffusion spectrum imaging (DSI) tractography to five juvenile ex vivo cat brains at postnatal day (P) 35, when the degree of myelination varies across brain regions. We quantified diffusion properties (fractional anisotropy [FA] and apparent diffusion coefficient [ADC]) and other measurements (number, volume, and voxel count) on reconstructed pathways for projection (cortico-spinal and thalamo-cortical), corpus callosal, limbic (cingulum and fornix), and association (cortico-cortical) pathways, and characterized regional differences in maturation patterns by assessing diffusion properties. FA values were significantly higher in cortico-cortical pathways within the right hemisphere compared to those within the left hemisphere, while the other measurements for the cortico-cortical pathways within the hemisphere did not show asymmetry. ADC values were not asymmetric in both types of pathways. Interestingly, tract count and volume were significantly larger in the left thalamo-cortical pathways compared to the right thalamo-cortical pathways. The bilateral thalamo-cortical pathways showed high FA values compared to the other fiber pathways. On the other hand, ADC values did not show any differences across pathways studied. These results demonstrate that DSI tractography successfully depicted regional variations of white matter tracts during development when myelination is incomplete. Low FA and high ADC values in the cingulum bundle suggest that the cingulum bundle is less mature than the others at this developmental stage. Copyright © 2016 ISDN. Published by Elsevier Ltd. All rights reserved.

Development, validation and psychometric properties of the Arabic version of the Orofacial Esthetic Scale: OES-Ar.

PubMed

Alhajj, Mohammed Nasser; Amran, Abdullah Ghalib; Halboub, Esam; Al-Basmi, Abdulghani Ali; Al-Ghabri, Fawaz Abdullah

2017-07-01

This study aimed at developing the Arabic version of the Orofacial Esthetic Scale (OES-Ar) and to investigate its psychometric properties among Arabic-speaking population with and without esthetic impairments. Translation and cross-cultural adaptation was done according to the standard guidelines. Internal consistency was assessed on 230 participants. For test-retest reliability, 50 subjects with natural teeth were recalled within a period of 2 weeks. Validity of the OES-Ar was tested by construct, convergent, and discriminant validity tests. Responsiveness to esthetic changes was assessed in 60 patients. The results showed excellent internal consistency with Cronbach's alpha value of 0.92 and inter-item correlation average value of 0.60. The ICC values ranged from 0.87 to 0.96 which indicated excellent agreement. Construct validity of the OES-Ar was confirmed to be one-factor structure (one-dimensional). For convergent validity, a significant correlation was found between OES summary score and overall impression of the orofacial esthetic as well as between OES summary score and the summary score of the three questions of the OHIP-49Ar related to esthetic. The discriminant validity test revealed significant differences between different study groups (P<0.001). Responsiveness to treatment was confirmed by significant differences between pre- and post-treatment OES total summary score (P<0.001). The OES-Ar has excellent psychometric properties making it valuable instrument to assess orofacial esthetics in Arabic-speaking patients. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Qualitative properties of roasting defect beans and development of its classification methods by hyperspectral imaging technology.

PubMed

Cho, Jeong-Seok; Bae, Hyung-Jin; Cho, Byoung-Kwan; Moon, Kwang-Deog

2017-04-01

Qualitative properties of roasting defect coffee beans and their classification methods were studied using hyperspectral imaging (HSI). The roasting defect beans were divided into 5 groups: medium roasting (Cont), under developed (RD-1), over roasting (RD-2), interior under developed (RD-3), and interior scorching (RD-4). The following qualitative properties were assayed: browning index (BI), moisture content (MC), chlorogenic acid (CA), trigonelline (TG), and caffeine (CF) content. Their HSI spectra (1000-1700nm) were also analysed to develop the classification methods of roasting defect beans. RD-2 showed the highest BI and the lowest MC, CA, and TG content. The accuracy of classification model of partial least-squares discriminant was 86.2%. The most powerful wavelength to classify the defective beans was approximately 1420nm (related to OH bond). The HSI reflectance values at 1420nm showed similar tendency with MC, enabling the use of this technology to classify the roasting defect beans. Copyright © 2016. Published by Elsevier Ltd.

Building an Open-source Simulation Platform of Acoustic Radiation Force-based Breast Elastography

PubMed Central

Wang, Yu; Peng, Bo; Jiang, Jingfeng

2017-01-01

Ultrasound-based elastography including strain elastography (SE), acoustic radiation force Impulse (ARFI) imaging, point shear wave elastography (pSWE) and supersonic shear imaging (SSI) have been used to differentiate breast tumors among other clinical applications. The objective of this study is to extend a previously published virtual simulation platform built for ultrasound quasi-static breast elastography toward acoustic radiation force-based breast elastography. Consequently, the extended virtual breast elastography simulation platform can be used to validate image pixels with known underlying soft tissue properties (i.e. “ground truth”) in complex, heterogeneous media, enhancing confidence in elastographic image interpretations. The proposed virtual breast elastography system inherited four key components from the previously published virtual simulation platform: an ultrasound simulator (Field II), a mesh generator (Tetgen), a finite element solver (FEBio) and a visualization and data processing package (VTK). Using a simple message passing mechanism, functionalities have now been extended to acoustic radiation force-based elastography simulations. Examples involving three different numerical breast models with increasing complexity – one uniform model, one simple inclusion model and one virtual complex breast model derived from magnetic resonance imaging data, were used to demonstrate capabilities of this extended virtual platform. Overall, simulation results were compared with the published results. In the uniform model, the estimated shear wave speed (SWS) values were within 4% compared to the predetermined SWS values. In the simple inclusion and the complex breast models, SWS values of all hard inclusions in soft backgrounds were slightly underestimated, similar to what has been reported. The elastic contrast values and visual observation show that ARFI images have higher spatial resolution, while SSI images can provide higher inclusion-to-background contrast. In summary, our initial results were consistent with our expectations and what have been reported in the literature. The proposed (open-source) simulation platform can serve as a single gateway to perform many elastographic simulations in a transparent manner, thereby promoting collaborative developments. PMID:28075330

Building an open-source simulation platform of acoustic radiation force-based breast elastography

NASA Astrophysics Data System (ADS)

Wang, Yu; Peng, Bo; Jiang, Jingfeng

2017-03-01

Ultrasound-based elastography including strain elastography, acoustic radiation force impulse (ARFI) imaging, point shear wave elastography and supersonic shear imaging (SSI) have been used to differentiate breast tumors among other clinical applications. The objective of this study is to extend a previously published virtual simulation platform built for ultrasound quasi-static breast elastography toward acoustic radiation force-based breast elastography. Consequently, the extended virtual breast elastography simulation platform can be used to validate image pixels with known underlying soft tissue properties (i.e. ‘ground truth’) in complex, heterogeneous media, enhancing confidence in elastographic image interpretations. The proposed virtual breast elastography system inherited four key components from the previously published virtual simulation platform: an ultrasound simulator (Field II), a mesh generator (Tetgen), a finite element solver (FEBio) and a visualization and data processing package (VTK). Using a simple message passing mechanism, functionalities have now been extended to acoustic radiation force-based elastography simulations. Examples involving three different numerical breast models with increasing complexity—one uniform model, one simple inclusion model and one virtual complex breast model derived from magnetic resonance imaging data, were used to demonstrate capabilities of this extended virtual platform. Overall, simulation results were compared with the published results. In the uniform model, the estimated shear wave speed (SWS) values were within 4% compared to the predetermined SWS values. In the simple inclusion and the complex breast models, SWS values of all hard inclusions in soft backgrounds were slightly underestimated, similar to what has been reported. The elastic contrast values and visual observation show that ARFI images have higher spatial resolution, while SSI images can provide higher inclusion-to-background contrast. In summary, our initial results were consistent with our expectations and what have been reported in the literature. The proposed (open-source) simulation platform can serve as a single gateway to perform many elastographic simulations in a transparent manner, thereby promoting collaborative developments.

Determination of the saturated film conductivity to improve the EMFX model in describing the soil hydraulic properties over the entire moisture range

NASA Astrophysics Data System (ADS)

Wang, Yunquan; Ma, Jinzhu; Guan, Huade; Zhu, Gaofeng

2017-06-01

Difficulty in measuring hydraulic conductivity, particularly under dry conditions, calls for methods of predicting the conductivity from easily obtained soil properties. As a complement to the recently published EMFX model, a method based on two specific suction conditions is proposed to estimate saturated film conductivity from the soil water retention curve. This method reduces one fitting parameter in the previous EMFX model, making it possible to predict the hydraulic conductivity from the soil water retention curve over the complete moisture range. Model performance is evaluated with published data of soils in a broad texture range from sand to clay. The testing results indicate that 1) the modified EMFX model (namely the EMFX-K model), incorporating both capillary and adsorption forces, provides good agreement with the conductivity data over the entire moisture range; 2) a value of 0.5 for the tortuosity factor in the EMFX-K model as that in the Mualem's model gives comparable estimation of the relative conductivity associated with the capillary force; and 3) a value of -1.0 × 10-20 J for the Hamaker constant, rather than the commonly used value of -6.0 × 10-20 J, appears to be more appropriate to represent solely the effect of the van der Waals forces and to predict the film conductivity. In comparison with the commonly used van Genuchten-Mualem model, the EMFX-K model significantly improves the prediction of hydraulic conductivity under dry conditions. The sensitivity analysis result suggests that the uncertainty in the film thickness estimation is important in explaining the model underestimation of hydraulic conductivity for the soils with fine texture, in addition to the uncertainties from the measurements and the model structure. High quality data that cover the complete moisture range for a variety of soil textures are required to further test the method.

Science and ethics meet: a mathematical view on one kind of violation of publication ethics

NASA Astrophysics Data System (ADS)

Shinyaeva, Taisiya S.; Tarasevich, Yuri Yu

2018-01-01

When a person who did not make a significant intellectual contribution to a published research is included into the co-author list, the person is called gift or guest author depending on the reason why the person has been added to the co-authors. Essential deviation of properties of a particular co-author network from typical values may evidenced that the network is artificial. Using network analysis, we have performed an attempt to characterize a typical co-author network. We performed analysis of the co-author networks using references in the thesis on Physics and Mathematics, Economics defended from 2012 to 2017 and planned to be defended in 2017 and 2018 in Russia. Properties of the co-author networks are expected to be a reference sample in future research.

Grain dynamics and plastic properties of highly refined materials

NASA Astrophysics Data System (ADS)

Lagos, Miguel; Retamal, César

2010-12-01

It has been shown that a grain boundary may undergo two competing classes of elastic instability when the in-plane shear stress exceeds the proper critical values. It may buckle acquiring a sinusoidal shape or may develop a periodic series of fissures, separating bands with a sigmoidal profile. The two instabilities lead to grain sliding, but the corresponding expressions relating the relative velocity between adjacent grains with stress do differ. The plastic properties for small strains were calculated for the two force laws, which we called force models A and B. A comparison of the theoretical results with published experimental data shows that model A, while giving predictions within the experimental uncertainties for a series of superplastic aluminium and titanium alloys, fails for Avesta 2304 steel. However, excellent results are obtained when model B is applied for this steel.

7 CFR 277.13 - Property.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the cost of the property to the current fair market value of the property. (3) Disposition. If the... the cost of the property to the current fair market value of the property, plus any shipping or... property to the current fair market value of the property, and for any reasonable shipping and interim...

Predicting SVOC Emissions into Air and Foods in Support of ...

EPA Pesticide Factsheets

The release of semi-volatile organic compounds (SVOCs) from consumer articles may be a critical human exposure pathway. In addition, the migration of SVOCs from food packaging materials into foods may also be a dominant source of exposure for some chemicals. Here we describe recent efforts to characterize emission-related parameters for these exposure pathways to support prediction of aggregate exposures for thousands of chemicals For chemicals in consumer articles, Little et al. (2012) developed a screening-level indoor exposure prediction model which, for a given SVOC, principally depends on steady-state gas-phase concentrations (y0). We have developed a model that predicts y0 for SVOCs in consumer articles, allowing exposure predictions for 274 ToxCast chemicals. Published emissions data for 31 SVOCs found in flooring materials, provided a training set where both chemical-specific physicochemical properties, article specific formulation properties, and experimental design aspects were available as modeling descriptors. A linear regression yielded R2- and p- values of approximately 0.62 and 3.9E-05, respectively. A similar model was developed based upon physicochemical properties alone, since article information is often not available for a given SVOC or product. This latter model yielded R2 - and p- values of approximately 0.47 and 1.2E-10, respectively. Many SVOCs are also used as additives (e.g. plasticizers, antioxidants, lubricants) in plastic food pac

Modeling global mangrove soil carbon stocks: filling the gaps in coastal environments

NASA Astrophysics Data System (ADS)

Rovai, A.; Twilley, R.

2017-12-01

We provide an overview of contemporaneous global mangrove soil organic carbon (SOC) estimates, focusing on a framework to explain disproportionate differences among observed data as a way to improve global estimates. This framework is based on a former conceptual model, the coastal environmental setting, in contrast to the more popular latitude-based hypotheses largely believed to explain hemispheric variation in mangrove ecosystem properties. To demonstrate how local and regional estimates of SOC linked to coastal environmental settings can render more realistic global mangrove SOC extrapolations we combined published and unpublished data, yielding a total of 106 studies, reporting on 552 sites from 43 countries. These sites were classified into distinct coastal environmental setting types according to two concurrent worldwide typology of nearshore coastal systems classifications. Mangrove SOC density varied substantially across coastal environmental settings, ranging from 14.9 ± 0.8 in river dominated (deltaic) soils to 53.9 ± 1.6 mg cm-3 (mean ± SE) in karstic coastlines. Our findings reveal striking differences between published values and contemporary global mangrove SOC extrapolation based on country-level mean reference values, particularly for karstic-dominated coastlines where mangrove SOC stocks have been underestimated by up to 50%. Correspondingly, climate-based global estimates predicted lower mangrove SOC density values (32-41 mg C cm-3) for mangroves in karstic environments, differing from published (21-126 mg C cm-3) and unpublished (47-58 mg C cm-3) values. Moreover, climate-based projections yielded higher SOC density values (27-70 mg C cm-3) for river-dominated mangroves compared to lower ranges reported in the literature (11-24 mg C cm-3). We argue that this inconsistent reporting of SOC stock estimates between river-dominated and karstic coastal environmental settings is likely due to the omission of geomorphological and geophysical environmental drivers, which control C storage in coastal wetlands. We encourage the science community more close utilize coastal environmental settings and new inventories of geomorphological typologies to build more robust estimates of local and regional estimates of SOC that can be extrapolated to global C estimates.

Automated identification of social interaction criteria in Drosophila melanogaster.

PubMed

Schneider, J; Levine, J D

2014-10-01

The study of social behaviour within groups has relied on fixed definitions of an 'interaction'. Criteria used in these definitions often involve a subjectively defined cut-off value for proximity, orientation and time (e.g. courtship, aggression and social interaction networks) and the same numerical values for these criteria are applied to all of the treatment groups within an experiment. One universal definition of an interaction could misidentify interactions within groups that differ in life histories, study treatments and/or genetic mutations. Here, we present an automated method for determining the values of interaction criteria using a pre-defined rule set rather than pre-defined values. We use this approach and show changing social behaviours in different manipulations of Drosophila melanogaster. We also show that chemosensory cues are an important modality of social spacing and interaction. This method will allow a more robust analysis of the properties of interacting groups, while helping us understand how specific groups regulate their social interaction space. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

Towards soil property retrieval from space: Proof of concept using in situ observations

NASA Astrophysics Data System (ADS)

Bandara, Ranmalee; Walker, Jeffrey P.; Rüdiger, Christoph

2014-05-01

Soil moisture is a key variable that controls the exchange of water and energy fluxes between the land surface and the atmosphere. However, the temporal evolution of soil moisture is neither easy to measure nor monitor at large scales because of its high spatial variability. This is mainly a result of the local variation in soil properties and vegetation cover. Thus, land surface models are normally used to predict the evolution of soil moisture and yet, despite their importance, these models are based on low-resolution soil property information or typical values. Therefore, the availability of more accurate and detailed soil parameter data than are currently available is vital, if regional or global soil moisture predictions are to be made with the accuracy required for environmental applications. The proposed solution is to estimate the soil hydraulic properties via model calibration to remotely sensed soil moisture observation, with in situ observations used as a proxy in this proof of concept study. Consequently, the feasibility is assessed, and the level of accuracy that can be expected determined, for soil hydraulic property estimation of duplex soil profiles in a semi-arid environment using near-surface soil moisture observations under naturally occurring conditions. The retrieved soil hydraulic parameters were then assessed by their reliability to predict the root zone soil moisture using the Joint UK Land Environment Simulator model. When using parameters that were retrieved using soil moisture observations, the root zone soil moisture was predicted to within an accuracy of 0.04 m3/m3, which is an improvement of ∼0.025 m3/m3 on predictions that used published values or pedo-transfer functions.

Pavlovian Conditioning of Social Exploration in Adult Female Rats.

PubMed

Sunsay, Ceyhun

2018-06-02

Social conditionaed place preference (SCPP) studies show that the reward value of social interaction is amenable to the laws of associative learning, such that it becomes associated with the physical properties of the context. However, social interaction can be initiated and maintained by a variety of motivations, such as the exploration of a novel conspecific, aggression, mutual grooming and mating-like actions. In order to study whether social exploration is rewarding, we used a conventional Pavlovian conditioning procedure in which access to a restrained same-sex rat served as a reward. Three dependent variables in two experiments showed that the reward value of social exploration becomes conditioned to a transient cue, and it is also subject to extinction and spontaneous recovery. The results may help to elucidate the mixed results obtained with SCPP procedures. Copyright © 2018. Published by Elsevier B.V.

Synthesis, structure, theoretical and experimental in vitro antioxidant/pharmacological properties of α-aryl, N-alkyl nitrones, as potential agents for the treatment of cerebral ischemia.

PubMed

Samadi, Abdelouahid; Soriano, Elena; Revuelta, Julia; Valderas, Carolina; Chioua, Mourad; Garrido, Ignacio; Bartolomé, Begoña; Tomassolli, Isabelle; Ismaili, Lhassane; González-Lafuente, Laura; Villarroya, Mercedes; García, Antonio G; Oset-Gasque, María J; Marco-Contelles, José

2011-01-15

The synthesis, structure, theoretical and experimental in vitro antioxidant properties using the DPPH, ORAC, and benzoic acid, as well as preliminary in vitro pharmacological activities of (Z)-α-aryl and heteroaryl N-alkyl-nitrones 6-15, 18, 19, 21, and 23, is reported. In the in vitro antioxidant activity, for the DPPH radical test, only nitrones bearing free phenol groups gave the best RSA (%) values, nitrones 13 and 14 showing the highest values in this assay. In the ORAC analysis, the most potent radical scavenger was nitrone indole 21, followed by the N-benzyl benzene-type nitrones 10 and 15. Interestingly enough, the archetypal nitrone 7 (PBN) gave a low RSA value (1.4%) in the DPPH test, or was inactive in the ORAC assay. Concerning the ability to scavenge the hydroxyl radical, all the nitrones studied proved active in this experiment, showing high values in the 94-97% range, the most potent being nitrone 14. The theoretical calculations for the prediction of the antioxidant power, and the potential of ionization confirm that nitrones 9 and 10 are among the best compounds in electron transfer processes, a result that is also in good agreement with the experimental values in the DPPH assay. The calculated energy values for the reaction of ROS (hydroxyl, peroxyl) with the nitrones predict that the most favourable adduct-spin will take place between nitrones 9, 10, and 21, a fact that would be in agreement with their experimentally observed scavenger ability. The in vitro pharmacological analysis showed that the neuroprotective profile of the target molecules was in general low, with values ranging from 0% to 18.7%, in human neuroblastoma cells stressed with a mixture of rotenone/oligomycin-A, being nitrones 18, and 6-8 the most potent, as they show values in the range 24-18.4%. Crown Copyright © 2010. Published by Elsevier Ltd. All rights reserved.

Consumer acceptance of orange juice mixed with water mint leave extract.

PubMed

Ali, Marwa Rashad

2017-10-31

Orange-Mint leaves juice was formulated using different addition percentages of mint leaves extract. The juice was aseptically processed, packed in glass bottles under sterilized environment and sterilized at 70°C for 15 minutes then storage at 5°C for 3 months. The physicochemical, nutritional value, microbiological and sensory characteristics of the juice was evaluated. There is no difference in pH, total soluble solids, ash, and total acidity in all samples moreover, the sample A2, "orange juice with 15% of mint leaves extract" recorded the best values of sensory evaluation, on the other hand, it was recorded lower values of vitamin C and total phenolic compound than sample (C) or (C1) because of increasing in addition% of mint leaves extract to orange juice. The sensory properties of juice samples were not remarkable any changes during storage. The result indicated that the juice was acceptable up to 3 months of storage 5°C. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Uniaxial compressive behavior of micro-pillars of dental enamel characterized in multiple directions.

PubMed

Yilmaz, Ezgi D; Jelitto, Hans; Schneider, Gerold A

2015-04-01

In this work, the compressive elastic modulus and failure strength values of bovine enamel at the first hierarchical level formed by hydroxyapatite (HA) nanofibers and organic matter are identified in longitudinal, transverse and oblique direction with the uniaxial micro-compression method. The elastic modulus values (∼70 GPa) measured here are within the range of results reported in the literature but these values were found surprisingly uniform in all orientations as opposed to the previous nanoindentation findings revealing anisotropic elastic properties in enamel. Failure strengths were recorded up to ∼1.7 GPa and different failure modes (such as shear, microbuckling, fiber fracture) governed by the orientation of the HA nanofibers were visualized. Structural irregularities leading to mineral contacts between the nanofibers are postulated as the main reason for the high compressive strength and direction-independent elastic behavior on enamels first hierarchical level. Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Ultrafiltration of skimmed goat milk increases its nutritional value by concentrating nonfat solids such as proteins, Ca, P, Mg, and Zn.

PubMed

Moreno-Montoro, Miriam; Olalla, Manuel; Giménez-Martínez, Rafael; Bergillos-Meca, Triana; Ruiz-López, María Dolores; Cabrera-Vique, Carmen; Artacho, Reyes; Navarro-Alarcón, Miguel

2015-11-01

Goat milk has been reported to possess good nutritional and health-promoting properties. Usually, it must be concentrated before fermented products can be obtained. The aim of this study was to compare physicochemical and nutritional variables among raw (RM), skimmed (SM), and ultrafiltration-concentrated skimmed (UFM) goat milk. The density, acidity, ash, protein, casein, whey protein, Ca, P, Mg, and Zn values were significantly higher in UFM than in RM or SM. Dry extract and fat levels were significantly higher in UFM than in SM, and Mg content was significantly higher in UFM than in RM. Ultrafiltration also increased the solubility of Ca and Mg, changing their distribution in the milk. The higher concentrations of minerals and proteins, especially caseins, increase the nutritional value of UFM, which may therefore be more appropriate for goat milk yogurt manufacturing in comparison to RM or SM. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Multichannel calculation of the very narrow Ds0 *(2317) and the very broad D0 *(2300-2400)

NASA Astrophysics Data System (ADS)

Rupp, G.; van Beveren, E.

2007-03-01

The narrow D s0 * (2317) and broad D 0 * (2300-2400) charmed scalar mesons and their radial excitations are described in a coupled-channel quark model that also reproduces the properties of the light scalar nonet. All two-meson channels containing ground-state pseudoscalars and vectors are included. The parameters are chosen fixed at published values, except for the overall coupling constant λ, which is fine-tuned to reproduce the D s0 * (2317) mass, and a damping constant α for subthreshold contributions. Variations of λ and D 0 * (2300-2400) pole postions are studied for different α values. Calculated cross-sections for S-wave DK and Dπ scattering, as well as resonance pole positions, are given for the value of α that fits the light scalars. The thus predicted radially excited state D s0 *‧(2850), with a width of about 50MeV, seems to have been observed already.

A unified relation for the solid-liquid interface free energy of pure FCC, BCC, and HCP metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, S. R.; Mendelev, M. I., E-mail: mendelev@ameslab.gov

2016-04-14

We study correlations between the solid-liquid interface (SLI) free energy and bulk material properties (melting temperature, latent heat, and liquid structure) through the determination of SLI free energies for bcc and hcp metals from molecular dynamics (MD) simulation. Values obtained for the bcc metals in this study were compared to values predicted by the Turnbull, Laird, and Ewing relations on the basis of previously published MD simulation data. We found that of these three empirical relations, the Ewing relation better describes the MD simulation data. Moreover, whereas the original Ewing relation contains two constants for a particular crystal structure, wemore » found that the first coefficient in the Ewing relation does not depend on crystal structure, taking a common value for all three phases, at least for the class of the systems described by embedded-atom method potentials (which are considered to provide a reasonable approximation for metals).« less

Heart Rate and Blood Pressure Centile Curves and Distributions by Age of Hospitalized Critically Ill Children.

PubMed

Eytan, Danny; Goodwin, Andrew J; Greer, Robert; Guerguerian, Anne-Marie; Laussen, Peter C

2017-01-01

Heart rate (HR) and blood pressure (BP) form the basis for monitoring the physiological state of patients. Although norms have been published for healthy and hospitalized children, little is known about their distributions in critically ill children. The objective of this study was to report the distributions of these basic physiological variables in hospitalized critically ill children. Continuous data from bedside monitors were collected and stored at 5-s intervals from 3,677 subjects aged 0-18 years admitted over a period of 30 months to the pediatric and cardiac intensive care units at a large quaternary children's hospital. Approximately 1.13 billion values served to estimate age-specific distributions for these two basic physiological variables: HR and intra-arterial BP. Centile curves were derived from the sample distributions and compared to common reference ranges. Properties such as kurtosis and skewness of these distributions are described. In comparison to previously published reference ranges, we show that children in these settings exhibit markedly higher HRs than their healthy counterparts or children hospitalized on in-patient wards. We also compared commonly used published estimates of hypotension in children (e.g., the PALS guidelines) to the values we derived from critically ill children. This is a first study reporting the distributions of basic physiological variables in children in the pediatric intensive care settings, and the percentiles derived may serve as useful references for bedside clinicians and clinical trials.

Strong antimicrobial activity of xanthohumol and other derivatives from hops (Humulus lupulus L.) on gut anaerobic bacteria.

PubMed

Cermak, Pavel; Olsovska, Jana; Mikyska, Alexandr; Dusek, Martin; Kadleckova, Zuzana; Vanicek, Jiri; Nyc, Otakar; Sigler, Karel; Bostikova, Vanda; Bostik, Pavel

2017-11-01

Anaerobic bacteria, such as Bacteroides fragilis or Clostridium perfringens, are part of indigenous human flora. However, Clostridium difficile represents also an important causative agent of nosocomial infectious antibiotic-associated diarrhoea. Treatment of C. difficile infection is problematic, making it imperative to search for new compounds with antimicrobial properties. Hops (Humulus lupulus L.) contain substances with antibacterial properties. We tested antimicrobial activity of purified hop constituents humulone, lupulone and xanthohumol against anaerobic bacteria. The antimicrobial activity was established against B. fragilis, C. perfringens and C. difficile strains according to standard testing protocols (CLSI, EUCAST), and the minimum inhibitory concentrations (MICs) and minimum bactericidal concentrations (MBC) were calculated. All C. difficile strains were toxigenic and clinically relevant, as they were isolated from patients with diarrhoea. Strongest antimicrobial effects were observed with xanthohumol showing MIC and MBC values of 15-107 μg/mL, which are close to those of conventional antibiotics in the strains of bacteria with increased resistance. Slightly higher MIC and MBC values were obtained with lupulone followed by higher values of humulone. Our study, thus, shows a potential of purified hop compounds, especially xanthohumol, as alternatives for treatment of infections caused by select anaerobic bacteria, namely nosocomial diarrhoea caused by resistant strains. © 2017 APMIS. Published by John Wiley & Sons Ltd.

On the role of API in determining porosity, pore structure and bulk modulus of the skeletal material in pharmaceutical tablets formed with MCC as sole excipient.

PubMed

Ridgway, Cathy; Bawuah, Prince; Markl, Daniel; Zeitler, J Axel; Ketolainen, Jarkko; Peiponen, Kai-Erik; Gane, Patrick

2017-06-30

The physical properties and mechanical integrity of pharmaceutical tablets are of major importance when loading with active pharmaceutical ingredient(s) (API) in order to ensure ease of processing, control of dosage and stability during transportation and handling prior to patient consumption. The interaction between API and excipient, acting as functional extender and binder, however, is little understood in this context. The API indomethacin is combined in this study with microcrystalline cellulose (MCC) at increasing loading levels. Tablets from the defined API/MCC ratios are made under conditions of controlled porosity and tablet thickness, resulting from different compression conditions, and thus compaction levels. Mercury intrusion porosimetry is used to establish the accessible pore volume, pore size distribution and, adopting the observed region of elastic intrusion-extrusion at high pressure, an elastic bulk modulus of the skeletal material is recorded. Porosity values are compared to previously published values derived from terahertz (THz) refractive index data obtained from exactly the same tablet sample sets. It is shown that the elastic bulk modulus is dependent on API wt% loading under constant tablet preparation conditions delivering equal dimensions and porosity. The findings are considered of novel value in respect to establishing consistency of tablet production and optimisation of physical properties. Copyright © 2017 Elsevier B.V. All rights reserved.

26 CFR 1.737-4 - Anti-abuse rule.

Code of Federal Regulations, 2010 CFR

2010-04-01

... contributed property) for each year of the partnership, the fair market value of partnership property does not.... A contributes Property A1, nondepreciable real property with a fair market value of $10,000 and an... to the partnership Property A2, nondepreciable real property with a fair market value and adjusted...

Observation of a different birefringence order at optical and THz frequencies in LBO crystal

NASA Astrophysics Data System (ADS)

Andreev, Yu. M.; Kokh, A. E.; Kokh, K. A.; Lanskii, G. V.; Litvinenko, K.; Mamrashev, A. A.; Molloy, J. F.; Murdin, B.; Naftaly, M.; Nikolaev, N. A.; Svetlichnyi, V. A.

2017-04-01

THz optical properties of lithium borate (LBO) crystals were measured using time-domain spectroscopy (TDS). The LBO crystal samples were of high optical quality and were cut and polished along the 〈100〉, 〈010〉 and 〈001〉 axes. Two independent measurements were performed in order to confirm the reproducibility and consistency of results. The contradictions in the previously published data on the THz optical properties of LBO were clarified. It was shown that the birefringence order at THz frequencies is nz

Environments Perceived as Obesogenic Have Lower Residential Property Values

PubMed Central

Drewnowski, Adam; Aggarwal, Anju; Rehm, Colin D.; Cohen-Cline, Hannah; Hurvitz, Philip M.; Moudon, Anne V.

2014-01-01

Background Studies have tried to link multiple aspects of the built environment with physical activity and obesity rates. Purpose To determine the relation between residential property values and multiple perceived (self-reported) measures of the obesogenic environment. Methods The Seattle Obesity Study (SOS) used a telephone survey of a representative, geographically distributed sample of 2,001 King County adults, collected in 2008–2009 and analyzed in 2012–2013. Home addresses were geocoded. Residential property values at the tax parcel level were obtained from the King County tax assessor. Mean residential property values within a 10-minute walk (833-meter buffer) were calculated for each respondent. Data on multiple perceived measures of the obesogenic environment were collected by self-report. Correlations and multivariable linear regression analyses, stratified by residential density, were used to examine the associations among perceived environmental measures, property values, and BMI. Results Perceived measures of the environment such as crime, heavy traffic, and proximity to bars, liquor stores, and fast food were all associated with lower property values. By contrast, living in neighborhoods that were perceived as safe, quiet, clean, and attractive was associated with higher property values. Higher property values were associated, in turn, with lower BMIs. The observed associations between perceived environment measures and BMI were largely attenuated after accounting for residential property values. Conclusions Perceived measures of obesogenic environments are associated with lower property values. Studies in additional locations need to explore to what extent other perceived environment measures can be reflected in residential property values. PMID:25049218

Solubility-product constant and thermodynamic properties for synthetic otavite, CdCO3(s), and aqueous association constants for the Cd(II)-CO2-H2O system

USGS Publications Warehouse

Stipp, S.L.S.; Parks, George A.; Nordstrom, D. Kirk; Leckie, J.O.

1993-01-01

Considerable disparity exists in the published thermodynamic data for selected species in the Cd(II)-CO2-H2O system near 25??C and 1 atm pressure. Evaluation of published experimental and estimated data for aqueous cadmium-carbonate species suggests an association constant, pK, of -3.0 ?? 0.4 for CdCO30, about -1.5 for CdHCO3+, and -6.4 ?? 0.1 for Cd(CO3)22- (T = 298.15 K; P = 1 atm; I = 0). Examination of all available data for cadmium-hydrolysis species and ??-Cd(OH)2(s)) confirms that the consistent set of constants presented by Baes and Mesmer (Hydrolysis of Cations, 1976) is the best available. The solubility of synthetic otavite, CdCO3(s), has been measured in KClO4 solutions where I ??? 0.1 M. We calculated pKsp = 12.1 ?? 0.1 (T = 25.0??C; P = 1 atm; I = 0) from measured concentrations of Cd2+, measured PC02 and pH, our selected set of equilibrium constants, and activity corrections estimated using the Davies equation. Values at 5 and 50??C were 12.4 ?? 0.1 and 12.2 ?? 0.1, respectively. Based on the new solubility data and the CODATA key values for Cd2+ and CO32-, a new set of thermodynamic properties is recommended for otavite: ??Gf0 = -674.7 ?? 0.6 kJ/mol; ??Hf0 = -751.9 ?? 10 kJ/mol; S0 = 106 ?? 30 J/mol K; and ??Gr0 for the reaction Cd2+ + CO32- ??? CdCO3(s) is -69.08 ?? 0.57 kJ/m. ?? 1993.

Physical properties and depth of cure of a new short fiber reinforced composite.

PubMed

Garoushi, Sufyan; Säilynoja, Eija; Vallittu, Pekka K; Lassila, Lippo

2013-08-01

To determine the physical properties and curing depth of a new short fiber composite intended for posterior large restorations (everX Posterior) in comparison to different commercial posterior composites (Alert, TetricEvoCeram Bulk Fill, Voco X-tra base, SDR, Venus Bulk Fill, SonicFill, Filtek Bulk Fill, Filtek Superme, and Filtek Z250). In addition, length of fiber fillers of composite XENIUS base compared to the previously introduced composite Alert has been measured. The following properties were examined according to ISO standard 4049: flexural strength, flexural modulus, fracture toughness, polymerization shrinkage and depth of cure. The mean and standard deviation were determined and all results were statistically analyzed with analysis of variance ANOVA (a=0.05). XENIUS base composite exhibited the highest fracture toughness (4.6MPam(1/2)) and flexural strength (124.3MPa) values and the lower shrinkage strain (0.17%) among the materials tested. Alert composite revealed the highest flexural modulus value (9.9GPa), which was not significantly different from XENIUS base composite (9.5GPa). Depth of cure of XENIUS base (4.6mm) was similar than those of bulk fill composites and higher than other hybrid composites. The length of fiber fillers in XENIUS base was longer (1.3-2mm) than in Alert (20-60μm). The new short fiber composite differed significantly in its physical properties compared to other materials tested. This suggests that the latter could be used in high-stress bearing areas. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Combined use of heat and saline tracer to estimate aquifer properties in a forced gradient test

NASA Astrophysics Data System (ADS)

Colombani, N.; Giambastiani, B. M. S.; Mastrocicco, M.

2015-06-01

Usually electrolytic tracers are employed for subsurface characterization, but the interpretation of tracer test data collected by low cost techniques, such as electrical conductivity logging, can be biased by cation exchange reactions. To characterize the aquifer transport properties a saline and heat forced gradient test was employed. The field site, located near Ferrara (Northern Italy), is a well characterized site, which covers an area of 200 m2 and is equipped with a grid of 13 monitoring wells. A two-well (injection and pumping) system was employed to perform the forced gradient test and a straddle packer was installed in the injection well to avoid in-well artificial mixing. The contemporary continuous monitor of hydraulic head, electrical conductivity and temperature within the wells permitted to obtain a robust dataset, which was then used to accurately simulate injection conditions, to calibrate a 3D transient flow and transport model and to obtain aquifer properties at small scale. The transient groundwater flow and solute-heat transport model was built using SEAWAT. The result significance was further investigated by comparing the results with already published column experiments and a natural gradient tracer test performed in the same field. The test procedure shown here can provide a fast and low cost technique to characterize coarse grain aquifer properties, although some limitations can be highlighted, such as the small value of the dispersion coefficient compared to values obtained by natural gradient tracer test, or the fast depletion of heat signal due to high thermal diffusivity.

Additively manufactured metallic porous biomaterials based on minimal surfaces: A unique combination of topological, mechanical, and mass transport properties.

PubMed

Bobbert, F S L; Lietaert, K; Eftekhari, A A; Pouran, B; Ahmadi, S M; Weinans, H; Zadpoor, A A

2017-04-15

Porous biomaterials that simultaneously mimic the topological, mechanical, and mass transport properties of bone are in great demand but are rarely found in the literature. In this study, we rationally designed and additively manufactured (AM) porous metallic biomaterials based on four different types of triply periodic minimal surfaces (TPMS) that mimic the properties of bone to an unprecedented level of multi-physics detail. Sixteen different types of porous biomaterials were rationally designed and fabricated using selective laser melting (SLM) from a titanium alloy (Ti-6Al-4V). The topology, quasi-static mechanical properties, fatigue resistance, and permeability of the developed biomaterials were then characterized. In terms of topology, the biomaterials resembled the morphological properties of trabecular bone including mean surface curvatures close to zero. The biomaterials showed a favorable but rare combination of relatively low elastic properties in the range of those observed for trabecular bone and high yield strengths exceeding those reported for cortical bone. This combination allows for simultaneously avoiding stress shielding, while providing ample mechanical support for bone tissue regeneration and osseointegration. Furthermore, as opposed to other AM porous biomaterials developed to date for which the fatigue endurance limit has been found to be ≈20% of their yield (or plateau) stress, some of the biomaterials developed in the current study show extremely high fatigue resistance with endurance limits up to 60% of their yield stress. It was also found that the permeability values measured for the developed biomaterials were in the range of values reported for trabecular bone. In summary, the developed porous metallic biomaterials based on TPMS mimic the topological, mechanical, and physical properties of trabecular bone to a great degree. These properties make them potential candidates to be applied as parts of orthopedic implants and/or as bone-substituting biomaterials. Bone-substituting biomaterials aim to mimic bone properties. Although mimicking some of bone properties is feasible, biomaterials that could simultaneously mimic all or most of the relevant bone properties are rare. We used rational design and additive manufacturing to develop porous metallic biomaterials that exhibit an interesting combination of topological, mechanical, and mass transport properties. The topology of the developed biomaterials resembles that of trabecular bone including a mean curvature close to zero. Moreover, the developed biomaterials show an unusual combination of low elastic modulus to avoid stress shielding and high strength to provide mechanical support. The fatigue resistance of the developed biomaterials is also exceptionally high, while their permeability is in the range of values reported for bone. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

41 CFR 105-74.220 - By when must I publish my drug-free workplace statement and establish my drug-free awareness...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false By when must I publish my drug-free workplace statement and establish my drug-free awareness program? 105-74.220 Section 105-74.220 Public Contracts and Property Management Federal Property Management Regulations System...

Utility-Based Instruments for People with Dementia: A Systematic Review and Meta-Regression Analysis.

PubMed

Li, Li; Nguyen, Kim-Huong; Comans, Tracy; Scuffham, Paul

2018-04-01

Several utility-based instruments have been applied in cost-utility analysis to assess health state values for people with dementia. Nevertheless, concerns and uncertainty regarding their performance for people with dementia have been raised. To assess the performance of available utility-based instruments for people with dementia by comparing their psychometric properties and to explore factors that cause variations in the reported health state values generated from those instruments by conducting meta-regression analyses. A literature search was conducted and psychometric properties were synthesized to demonstrate the overall performance of each instrument. When available, health state values and variables such as the type of instrument and cognitive impairment levels were extracted from each article. A meta-regression analysis was undertaken and available covariates were included in the models. A total of 64 studies providing preference-based values were identified and included. The EuroQol five-dimension questionnaire demonstrated the best combination of feasibility, reliability, and validity. Meta-regression analyses suggested that significant differences exist between instruments, type of respondents, and mode of administration and the variations in estimated utility values had influences on incremental quality-adjusted life-year calculation. This review finds that the EuroQol five-dimension questionnaire is the most valid utility-based instrument for people with dementia, but should be replaced by others under certain circumstances. Although no utility estimates were reported in the article, the meta-regression analyses that examined variations in utility estimates produced by different instruments impact on cost-utility analysis, potentially altering the decision-making process in some circumstances. Copyright © 2018 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Physicochemical, microbial, and sensory properties of nanopowdered eggshell-supplemented yogurt during storage.

PubMed

Al Mijan, Mohammad; Choi, Kyung-Hoon; Kwak, Hae-Soo

2014-01-01

This study was carried out to investigate the possibility of adding nanopowdered eggshell (NPES) into yogurt to improve the functionality of yogurt and the effects of adding NPES on the physicochemical, microbial, and sensory properties of the products during storage. The pH and mean lactic acid bacteria counts of NPES-added (0.15-0.45%, wt/vol) yogurt ranged from 4.31 to 4.66 and from 6.56 × 10(8) to 8.56 × 10(8)cfu/mL, respectively, whereas these values ranged from 4.13 to 4.44 and 8.46 × 10(8) to 1.39 × 10(9), respectively, for the control samples during storage at 5 °C for 16d, which indicates a prolonged shelf-life with NPES-supplemented yogurt. Color analysis showed that the lightness (L*) and position between red and green (a*) values were not significantly influenced by the addition of NPES. However, the position between yellow and blue (b*) value significantly increased with the addition of the concentration (0.45%, wt/vol) of NPES at d 16 of storage. Sensory evaluation revealed that NPES-added yogurts showed a notably less sourness score and a higher astringency score than the control. An earthy flavor was higher in 0.45% NPES-supplemented yogurt compared with the control. Based on the results obtained from the current study, the concentration (0.15 to 0.30%, wt/vol) of NPES can be used to formulate NPES-supplemented yogurt without any significant adverse effects on the physicochemical, microbial, and sensory properties. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Optical and transport properties of dense liquid silica

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qi, Tingting; Millot, Marius; Kraus, Richard G.

2015-06-15

Using density-functional-theory based molecular dynamics and the Kubo-Greenwood linear response theory, we evaluated the high-pressure equation of state and the optical and transport properties of quartz and fused silica shock-compressed to 2000 GPa. The computed Hugoniots and corresponding optical reflectivity values are in very good agreement with published data for quartz, and new data that we obtained on fused silica using magnetically launched flyer plate experiments. The rise of optical reflectivity upon shock compression appears to be primarily a temperature-driven mechanism, which is relatively insensitive to small density variation. We observed that the electrical conductivity does not display Drude-like frequencymore » dependence, especially at lower temperatures. In addition, the Wiedemann-Franz relation between electrical and thermal conductivities was found to be invalid. It suggests that even at three-fold compression, warm dense liquid silica on the Hugoniot curve is still far away from the degenerate limit.« less

The complexity of silk under the spotlight of synthetic biology.

PubMed

Vollrath, Fritz

2016-08-15

For centuries silkworm filaments have been the focus of R&D innovation centred on textile manufacture with high added value. Most recently, silk research has focused on more fundamental issues concerning bio-polymer structure-property-function relationships. This essay outlines the complexity and fundamentals of silk spinning, and presents arguments for establishing this substance as an interesting and important subject at the interface of systems biology (discovery) and synthetic biology (translation). It is argued that silk is a generic class of materials where each type of silk presents a different embodiment of emergent properties that combine genetically determined (anticipatory) and environmentally responsive components. In spiders' webs the various silks have evolved to form the interactive components of an intricate fabric that provides an extended phenotype to the spider's body morphology. © 2016 The Author(s). published by Portland Press Limited on behalf of the Biochemical Society.

Rational Improvement of Molar Absorptivity Guided by Oscillator Strength: A Case Study with Furoindolizine-Based Core Skeleton.

PubMed

Lee, Youngjun; Jo, Ala; Park, Seung Bum

2015-12-21

The rational improvement of photophysical properties can be highly valuable for the discovery of novel organic fluorophores. Using our new design strategy guided by the oscillator strength, we developed a series of full-color-tunable furoindolizine analogs with improved molar absorptivity through the fusion of a furan ring into the indolizine-based Seoul fluorophore. The excellent correlation between the computable values (oscillator strength and theoretical S0 -S1 energy gap) and photophysical properties (molar absorptivity and emission wavelength) confirmed the effectualness of our design strategy. © 2015 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA. This is an open access article under the terms of the Creative Commons Attribution Non-Commercial NoDerivs License, which permits use and distribution in any medium, provided the original work is properly cited, the use is non-commercial and no modifications or adaptations are made.

Exotic forest insects and residential property values

Treesearch

Thomas P. Holmes; Elizabeth A. Murphy; Kathleen P. Bell

2006-01-01

This paper presents a case study of the economic damages to homeowners in a northern New Jersey community due to an exotic forest insect-the hemlock woolly adelgid. Hedonic property value methods are used to estimate the effect of hemlock health on property values. A statistically significant relationship between hemlock health and residential property values is...

10 CFR 603.535 - Value of proposed real property or equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Value of proposed real property or equipment. 603.535... AGREEMENTS Pre-Award Business Evaluation Cost Sharing § 603.535 Value of proposed real property or equipment. The contracting officer rarely should accept values for cost sharing contributions of real property or...

Prediction of frozen food properties during freezing using product composition.

PubMed

Boonsupthip, W; Heldman, D R

2007-06-01

Frozen water fraction (FWF), as a function of temperature, is an important parameter for use in the design of food freezing processes. An FWF-prediction model, based on concentrations and molecular weights of specific product components, has been developed. Published food composition data were used to determine the identity and composition of key components. The model proposed in this investigation had been verified using published experimental FWF data and initial freezing temperature data, and by comparison to outputs from previously published models. It was found that specific food components with significant influence on freezing temperature depression of food products included low molecular weight water-soluble compounds with molality of 50 micromol per 100 g food or higher. Based on an analysis of 200 high-moisture food products, nearly 45% of the experimental initial freezing temperature data were within an absolute difference (AD) of +/- 0.15 degrees C and standard error (SE) of +/- 0.65 degrees C when compared to values predicted by the proposed model. The predicted relationship between temperature and FWF for all analyzed food products provided close agreements with experimental data (+/- 0.06 SE). The proposed model provided similar prediction capability for high- and intermediate-moisture food products. In addition, the proposed model provided statistically better prediction of initial freezing temperature and FWF than previous published models.

Measurement of soot morphology, chemistry, and optical properties in the visible and near-infrared spectrum in the flame zone and overfire region of large JP-8 pool fires.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suo-Anttila, Jill Marie; Jensen, Kirk A.; Blevins, Linda Gail

2005-03-01

The dimensionless extinction coefficient, K{sub e}, was measured for soot produced in 2 m JP-8 pool fires. Light extinction and gravimetric sampling measurements were performed simultaneously at 635 and 1310 nm wavelengths at three heights in the flame zone and in the overfire region. Measured average K{sub e} values of 8.4 {+-} 1.2 at 635 nm and 8.7 {+-} 1.1 at 1310 nm in the overfire region agree well with values from 8-10 recently reported for different fuels and flame conditions. The overfire K{sub e} values are also relatively independent of wavelength, in agreement with recent findings for JP-8 sootmore » in smaller flames. K{sub e} was nearly constant at 635 nm for all sampling locations in the large fires. However, at 1310 nm, the overfire K{sub e} was higher than in the flame zone. Chemical analysis of physically sampled soot shows variations in carbon-to-hydrogen (C/H) ratio and polycyclic aromatic hydrocarbon (PAH) concentration that may account for the smaller K{sub e} values measured in the flame zone. Rayleigh-Debye-Gans theory of scattering for polydisperse fractal aggregate (RDG-PFA) was applied to measured aggregate fractal dimensions and found to under-predict the extinction coefficient by 17-30% at 635 nm using commonly accepted refractive indices of soot, and agreed well with the experiments using the more recently published refractive index of 1.99-0.89i. This study represents the first measurements of soot chemistry, morphology, and optical properties in the flame zone of large, fully-turbulent pool fires, and emphasizes the importance of accurate measurements of optical properties both in the flame zone and overfire regions for models of radiative transport and interpretation of laser-based diagnostics of soot volume fraction and temperature.« less

Properties of Cast Films Made from Different Ratios of Whey Protein Isolate, Hydrolysed Whey Protein Isolate and Glycerol

PubMed Central

Schmid, Markus

2013-01-01

Whey protein isolate (WPI)-based cast films are very brittle, due to several chain interactions caused by a large amount of different functional groups. In order to overcome film brittleness, plasticizers, like glycerol, are commonly used. As a result of adding plasticizers, the free volume between the polymer chains increases, leading to higher permeability values. The objective of this study was to investigate the effect of partially substituting glycerol by hydrolysed whey protein isolate (h-WPI) in WPI-based cast films on their mechanical, optical and barrier properties. As recently published by the author, it is proven that increasing the h-WPI content in WPI-based films at constant glycerol concentrations significantly increases film flexibility, while maintaining the barrier properties. The present study considered these facts in order to increase the barrier performance, while maintaining film flexibility. Therefore glycerol was partially replaced by h-WPI in WPI-based cast films. The results clearly indicate that partially replacing glycerol by h-WPI reduces the oxygen permeability and the water vapor transmission rate, while the mechanical properties did not change significantly. Thus, film flexibility was maintained, even though the plasticizer concentration was decreased. PMID:28811434

Morphology, mechanical and thermal oxidative aging properties of HDPE composites reinforced by nonmetals recycled from waste printed circuit boards.

PubMed

Yang, Shuangqiao; Bai, Shibing; Wang, Qi

2016-11-01

In this study nonmetals recycled from waste printed circuit boards (NPCB) is used as reinforce fillers in high-density polyethylene (HDPE) composites. The morphology, mechanical and thermal oxidative aging properties of NPCB reinforced HDPE composites are assessed and it compared with two other commercial functional filler for the first time. Mechanical test results showed that NPCB could be used as reinforcing fillers in the HDPE composites and mechanical properties especially for stiffness is better than other two commercial fillers. The improved mechanical property was confirmed by the higher aspect ratio and strong interfacial adhesion in scanning electron microscopy (SEM) studies. The heat deflection temperature (HDT) test showed the presence of fiberglass in NPCB can improve the heat resistance of composite for their potential applications. Meanwhile, the oxidation induction time (OIT) and the Fourier transform infrared (FTIR) spectroscopy results showed that NPCB has a near resistance to oxidation as two other commercial fillers used in this paper. The above results show the reuse of NPCB in the HDPE composites represents a promising way for resolving both the environmental pollution and the high-value reuse of resources. Copyright © 2015. Published by Elsevier Ltd.

Carotenoid Derivates in Achiote (Bixa orellana) Seeds: Synthesis and Health Promoting Properties

PubMed Central

Rivera-Madrid, Renata; Aguilar-Espinosa, Margarita; Cárdenas-Conejo, Yair; Garza-Caligaris, Luz E.

2016-01-01

Bixa orellana (family Bixaceae) is a neotropical fast growing perennial tree of great agro-industrial value because its seeds have a high carotenoid content, mainly bixin. It has been used since pre-colonial times as a culinary colorant and spice, and for healing purposes. It is currently used as a natural pigment in the food, in pharmaceutical, and cosmetic industries, and it is commercially known as annatto. Recently, several studies have addressed the biological and medical properties of this natural pigment, both as potential source of new drugs or because its ingestion as a condiment or diet supplement may protect against several diseases. The most documented properties are anti-oxidative; but its anti-cancer, hypoglucemic, antibiotic and anti-inflammatory properties are also being studied. Bixin’s pathway elucidation and its regulation mechanisms are critical to improve the produce of this important carotenoid. Even though the bixin pathway has been established, the regulation of the genes involved in bixin production remains largely unknown. Our laboratory recently published B. orellana’s transcriptome and we have identified most of its MEP (methyl-D-erythritol 4-phosphate) and carotenoid pathway genes. Annatto is a potential source of new drugs and can be a valuable nutraceutical supplement. However, its nutritional and healing properties require further study. PMID:27708658

QUALITY OF WOOD PELLETS PRODUCED IN BRITISH COLUMBIA FOR EXPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tumuluru, J.S.; Sokhansanj, Shahabaddine; Lim, C. Jim

2010-11-01

Wood pellet production and its use for heat and power production are increasing worldwide. The quality of export pellets has to consistently meet certain specifications as stipulated by the larger buyers, such as power utilities or as specified by the standards used for the non-industrial bag market. No specific data is available regarding the quality of export pellets to Europe. To develop a set of baseline data, wood pellets were sampled at an export terminal in Vancouver, British Columbia, Canada. The sampling period was 18 months in 2007-2008 when pellets were transferred from storage bins to the ocean vessels. Themore » sampling frequency was once every 1.5 to 2 months for a total of 9 loading/shipping events. The physical properties of the wood pellets measured were moisture content in the range of 3.5% to 6.5%, bulk density from 728 to 808 kg/m3, durability from 97% to 99%, fines content from 0.03% to 0.87%, calorific value as is from 17 to almost 18 MJ/kg, and ash content from 0.26% to 0.93%.The diameter and length were in the range of 6.4 to 6.5 mm and 14.0 to 19.0 mm, respectively. All of these values met the published non-industrial European grades (CEN) and the grades specified by the Pellet Fuel Institute for the United States for the bag market. The measured values for wood pellet properties were consistent except the ash content values decreased over the test period.« less

Quality of Wood Pellets Produced in British Columbia for Export

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. S. Tumuluru; S. Sokhansanj; C. J. Lim

2010-11-01

Wood pellet production and its use for heat and power production are increasing worldwide. The quality of export pellets has to consistently meet certain specifications as stipulated by the larger buyers, such as power utilities or as specified by the standards used for the non-industrial bag market. No specific data is available regarding the quality of export pellets to Europe. To develop a set of baseline data, wood pellets were sampled at an export terminal in Vancouver, British Columbia, Canada. The sampling period was 18 months in 2007-2008 when pellets were transferred from storage bins to the ocean vessels. Themore » sampling frequency was once every 1.5 to 2 months for a total of 9 loading/shipping events. The physical properties of the wood pellets measured were moisture content in the range of 3.5% to 6.5%, bulk density from 728 to 808 kg/m3, durability from 97% to 99%, fines content from 0.03% to 0.87%, calorific value as is from 17 to almost 18 MJ/kg, and ash content from 0.26% to 0.93%.The diameter and length were in the range of 6.4 to 6.5 mm and 14.0 to 19.0 mm, respectively. All of these values met the published non-industrial European grades (CEN) and the grades specified by the Pellet Fuel Institute for the United States for the bag market. The measured values for wood pellet properties were consistent except the ash content values decreased over the test period.« less

On collisional disruption - Experimental results and scaling laws

NASA Technical Reports Server (NTRS)

Davis, Donald R.; Ryan, Eileen V.

1990-01-01

Both homogeneous and inhomogeneous targets have been addressed by the present experimental consideration of the impact strengths, fragment sizes, and fragment velocities generated by cement mortar targets whose crushing strengths vary by an order of magnitude, upon impact of projectiles in the velocity range of 50-5700 m/sec. When combined with additional published data, dynamic impact strength is found to correlate with quasi-static material strengths for materials ranging in character from basalt to ice; two materials not following this trend, however, are weak mortar and clay targets. Values consistent with experimental results are obtainable with a simple scaling algorithm based on impact energy, material properties, and collisional strain rate.

Measuring the elastic properties of fine wire.

PubMed

Fallen, C T; Costello, J; Crawford, G; Schmidt, J A

2001-01-01

The elastic moduli of fine wires made from MP35N and 304SS used in implantable biomedical devices are assumed to be the same as those published in the literature. However, the cold working required to manufacture the wire significantly alters the elastic moduli of the material. We describe three experiments performed on fine wire made from MP35N and 304SS. The experimentally determined Young's and shear modulus of both wire types were significantly less than the moduli reported in the literature. Young's modulus differed by as much as 26%, and the shear modulus differed by as much as 14% from reported values.

Alteration of Dentin-Enamel Mechanical Properties Due to Dental Whitening Treatments

PubMed Central

Zimmerman, B.; Datko, L.; Cupelli, M.; Alapati, S.; Dean, D.; Kennedy, M.

2010-01-01

The mechanical properties of dentin and enamel affect the reliability and wear properties of a tooth. This study investigated the influence of clinical dental treatments and procedures, such as whitening treatments or etching prior to restorative procedures. Both autoclaved and non-autoclaved teeth were studied in order to allow for both comparison with published values and improved clinical relevance. Nanoindentation analysis with the Oliver-Pharr model provided elastic modulus and hardness across the dentin-enamel junction (DEJ). Large increases were observed in the elastic modulus of enamel in teeth that had been autoclaved (52.0GPa versus 113.4GPa), while smaller increases were observed in the dentin (17.9GPa versus 27.9GPa). Likewise, there was an increase in the hardness of enamel (2.0GPa versus 4.3GPa) and dentin (0.5GPa versus 0.7GPa) with autoclaving. These changes suggested that the range of elastic modulus and hardness values previously reported in literature may be partially due to the sterilization procedures. Treatment of the exterior of non-autoclaved teeth with Crest Whitestrips™, Opalescence™ or UltraEtch™ caused changes in the mechanical properties of both the enamel and dentin. Those treated with Crest Whitestrips™ showed a reduction in the elastic modulus of enamel (55.3GPa to 32.7GPa) and increase in the elastic modulus of dentin (17.2GPa to 24.3GPa). Opalescence™ treatments did not significantly affect the enamel properties, but did result in a decrease in modulus of dentin (18.5GPa to 15.1GPa). Additionally, as expected, UltraEtch™ treatment decreased the modulus and hardness of enamel (48.7GPa to 38.0GPa and 1.9GPa to 1.5GPa, respectively) and dentin (21.4GPa to 15.0GPa and 1.9GPa to 1.5GPa, respectively). Changes in the mechanical properties were linked to altered protein concentration within the tooth, as evidenced by fluorescence microscopy and Fourier transform infrared spectroscopy. PMID:20346902

The experimental design approach to eluotropic strength of 20 solvents in thin-layer chromatography on silica gel.

PubMed

Komsta, Łukasz; Stępkowska, Barbara; Skibiński, Robert

2017-02-03

The eluotropic strength on thin-layer silica plates was investigated for 20 chromatographic grade solvents available in current market. 35 model compounds were used as test subjects in the investigation. The use of modern mixture screening design allowed to estimate each solvent as a separate elution coefficient with an acceptable error of estimation (0.0913 of R M value). Additional bootstrapping technique was used to check the distribution and uncertainty of eluotropic estimates, proving very similar confidence intervals to linear regression. Principal component analysis proved that the only one parameter (mean eluotropic strength) is satisfactory to describe the solvent property, as it explains almost 90% of variance of retention. The obtained eluotropic data can be good appendix to earlier published results and their values can be interpreted in context of R M differences. Copyright © 2017 Elsevier B.V. All rights reserved.

The experimental design approach to eluotropic strength of 20 solvents in thin-layer chromatography on silica gel.

PubMed

Komsta, Łukasz; Stępkowska, Barbara; Skibiński, Robert

2017-01-04

The eluotropic strength on thin-layer silica plates was investigated for 20 chromatographic grade solvents available in current market. 35 model compounds were used as test subjects in the investigation. The use of modern mixture screening design allowed to estimate each solvent as a separate elution coefficient with an acceptable error of estimation (0.0913 of R M value). Additional bootstrapping technique was used to check the distribution and uncertainty of eluotropic estimates, proving very similar confidence intervals to linear regression. Principal component analysis proved that the only one parameter (mean eluotropic strength) is satisfactory to describe the solvent property, as it explains almost 90% of variance of retention. The obtained eluotropic data can be good appendix to earlier published results and their values can be interpreted in context of R M differences. Copyright © 2017 Elsevier B.V. All rights reserved.

Graphene for energy solutions and its industrialization.

PubMed

Wei, Di; Kivioja, Jani

2013-11-07

Graphene attracts intensive interest globally across academia and industry since the award of the Nobel Prize in Physics 2010. Within the last half decade, there has been an explosion in the number of scientific publications, patents and industry projects involved in this topic. On the other hand, energy is one of the biggest challenges of this century and related to the global sustainable economy. There are many reviews on graphene and its applications in various devices, however, few of the review articles connect the intrinsic properties of graphene with its energy. The IUPAC definition of graphene refers to a single carbon layer of graphite structure and its related superlative properties. A lot of scientific results on graphene published to date are actually dealing with multi-layer graphenes or reduced graphenes from insulating graphene oxides (GO) which contain defects and contaminants from the reactions and do not possess some of the intrinsic physical properties of pristine graphene. In this review, the focus is on the most recent advances in the study of pure graphene properties and novel energy solutions based on these properties. It also includes graphene metrology and analysis of both intellectual property and the value chain for the existing and forthcoming graphene industry that may cause a new 'industry revolution' with the strong and determined support of governments and industries across the European Union, U. S., Asia and many other countries in the world.

The Tuskegee Syphilis Experiment: biotechnology and the administrative state.

PubMed

Roy, B

1995-01-01

The central issue of the Tuskegee Syphilis Experiment was property: property in the body and intellectual property. Once removed from the body, tissue and body fluids were not legally the property of the Tuskegee subjects. Consequently, there was not a direct relationship between a patient and research that used his sera. The Public Health Service (PHS) was free to exercise its property right in Tuskegee sera to develop serologic tests for syphilis with commercial potential. To camouflage the true meaning, the PHS made a distinction between direct clinical studies and indirect studies of tissue and body fluids. This deception caused all reviews to date to limit their examination to documents labeled by the PHS as directly related to the Tuskegee Syphilis Experiment. This excluded other information in the public domain. Despite the absence of a clinical protocol, this subterfuge led each to falsely conclude that the Tuskagee Syphilis Experiment was a clinical study. Based on publications of indirect research using sera and cerebrospinal fluid, this article conceives a very history of the Tuskagee Syphilis Experiment. Syphilis could only cultivate in living beings. As in slavery, the generative ability of the body made the Tuskegee subjects real property and gave untreated syphilis and the sera of the Tuskegee subjects immense commercial value. Published protocols exploited the Tuskegee Syphilis Experiment to invent and commercialize biotechnology for the applied science of syphilis serology.

The Tuskegee Syphilis Experiment: biotechnology and the administrative state.

PubMed Central

Roy, B.

1995-01-01

The central issue of the Tuskegee Syphilis Experiment was property: property in the body and intellectual property. Once removed from the body, tissue and body fluids were not legally the property of the Tuskegee subjects. Consequently, there was not a direct relationship between a patient and research that used his sera. The Public Health Service (PHS) was free to exercise its property right in Tuskegee sera to develop serologic tests for syphilis with commercial potential. To camouflage the true meaning, the PHS made a distinction between direct clinical studies and indirect studies of tissue and body fluids. This deception caused all reviews to date to limit their examination to documents labeled by the PHS as directly related to the Tuskegee Syphilis Experiment. This excluded other information in the public domain. Despite the absence of a clinical protocol, this subterfuge led each to falsely conclude that the Tuskagee Syphilis Experiment was a clinical study. Based on publications of indirect research using sera and cerebrospinal fluid, this article conceives a very history of the Tuskagee Syphilis Experiment. Syphilis could only cultivate in living beings. As in slavery, the generative ability of the body made the Tuskegee subjects real property and gave untreated syphilis and the sera of the Tuskegee subjects immense commercial value. Published protocols exploited the Tuskegee Syphilis Experiment to invent and commercialize biotechnology for the applied science of syphilis serology. PMID:7869408

Resistant starch in food: a review.

PubMed

Raigond, Pinky; Ezekiel, Rajarathnam; Raigond, Baswaraj

2015-08-15

The nutritional property of starch is related to its rate and extent of digestion and absorption in the small intestine. For nutritional purposes, starch is classified as rapidly available, slowly available and resistant starch (RS). The exact underlying mechanism of relative resistance of starch granules is complicated because those factors are often interconnected. The content of RS in food is highly influenced by food preparation manner and processing techniques. Physical or chemical treatments also alter the level of RS in a food. Commercial preparations of RS are now available and can be added to foods as an ingredient for lowering the calorific value and improving textural and organoleptic characteristics along with increasing the amount of dietary fiber. RS has assumed great importance owing to its unique functional properties and health benefits. The beneficial effects of RS include glycemic control and control of fasting plasma triglyceride and cholesterol levels and absorption of minerals. This review attempts to analyze the information published, especially in the recent past, on classification, structure, properties, applications and health benefits of RS. © 2014 Society of Chemical Industry.

General Pharmacokinetic Model for Topically Administered Ocular Drug Dosage Forms.

PubMed

Deng, Feng; Ranta, Veli-Pekka; Kidron, Heidi; Urtti, Arto

2016-11-01

In ocular drug development, an early estimate of drug behavior before any in vivo experiments is important. The pharmacokinetics (PK) and bioavailability depend not only on active compound and excipients but also on physicochemical properties of the ocular drug formulation. We propose to utilize PK modelling to predict how drug and formulational properties affect drug bioavailability and pharmacokinetics. A physiologically relevant PK model based on the rabbit eye was built to simulate the effect of formulation and physicochemical properties on PK of pilocarpine solutions and fluorometholone suspensions. The model consists of four compartments: solid and dissolved drug in tear fluid, drug in corneal epithelium and aqueous humor. Parameter values and in vivo PK data in rabbits were taken from published literature. The model predicted the pilocarpine and fluorometholone concentrations in the corneal epithelium and aqueous humor with a reasonable accuracy for many different formulations. The model includes a graphical user interface that enables the user to modify parameters easily and thus simulate various formulations. The model is suitable for the development of ophthalmic formulations and the planning of bioequivalence studies.

Molecular dynamics study of lipid bilayers modeling the plasma membranes of mouse hepatocytes and hepatomas.

PubMed

Andoh, Yoshimichi; Aoki, Noriyuki; Okazaki, Susumu

2016-02-28

Molecular dynamics (MD) calculations of lipid bilayers modeling the plasma membranes of normal mouse hepatocytes and hepatomas in water have been performed under physiological isothermal-isobaric conditions (310.15 K and 1 atm). The changes in the membrane properties induced by hepatic canceration were investigated and were compared with previous MD calculations included in our previous study of the changes in membrane properties induced by murine thymic canceration. The calculated model membranes for normal hepatocytes and hepatomas comprised 23 and 24 kinds of lipids, respectively. These included phosphatidylcholine, phosphatidylethanolamine, phosphatidylserine, phosphatidylinositol, sphingomyelin, lysophospholipids, and cholesterol. We referred to previously published experimental values for the mole fraction of the lipids adopted in the present calculations. The calculated structural and dynamic properties of the membranes such as lateral structure, order parameters, lateral self-diffusion constants, and rotational correlation times all showed that hepatic canceration causes plasma membranes to become more ordered laterally and less fluid. Interestingly, this finding contrasts with the less ordered structure and increased fluidity of plasma membranes induced by thymic canceration observed in our previous MD study.

Electronic and thermoelectric properties of atomically thin C₃Si₃/C and C₃Ge₃/C superlattices.

PubMed

Ali, Muhammad; Pi, Xiaodong; Liu, Yong; Yang, Deren

2017-12-01

The nanostructuring of graphene into superlattices offers the possibility of tuning both the electronic and thermal properties of graphene. Using classical and quantum mechanical calculations, we have investigated the electronic and thermoelectric properties of the atomically thin superlattice of C3Si3/C (C3Ge3/C) formed by the incorporation of Si (Ge) atoms into graphene. The bandgap and phonon thermal conductivity of C3Si3/C (C3Ge3/C) are 0.54 (0.51) eV and 15.48 (12.64) Wm-1K-1, respectively, while the carrier mobility of C3Si3/C (C3Ge3/C) is 1.285 x 105 (1.311 x 105) cm2V-1s-1 at 300 K. The thermoelectric figure of merit for C3Si3/C (C3Ge3/C) can be optimized via the tuning of carrier concentration to obtain the prominent ZT value of 1.95 (2.72). © 2017 IOP Publishing Ltd.

Characterization of a polymer-infiltrated ceramic-network material.

PubMed

Della Bona, Alvaro; Corazza, Pedro H; Zhang, Yu

2014-05-01

To characterize the microstructure and determine some mechanical properties of a polymer-infiltrated ceramic-network (PICN) material (Vita Enamic, Vita Zahnfabrik) available for CAD-CAM systems. Specimens were fabricated to perform quantitative and qualitative analyses of the material's microstructure and to determine the fracture toughness (KIc), density (ρ), Poisson's ratio (ν) and Young's modulus (E). KIc was determined using V-notched specimens and the short beam toughness method, where bar-shaped specimens were notched and 3-point loaded to fracture. ρ was calculated using Archimedes principle, and ν and E were measured using an ultrasonic thickness gauge with a combination of a pulse generator and an oscilloscope. Microstructural analyses showed a ceramic- and a polymer-based interpenetrating network. Mean and standard deviation values for the properties evaluated were: KIc=1.09±0.05MPam(1/2), ρ=2.09±0.01g/cm(3), ν=0.23±0.002 and E=37.95±0.34GPa. The PICN material showed mechanical properties between porcelains and resin-based composites, reflecting its microstructural components. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Molecular dynamics study of lipid bilayers modeling the plasma membranes of mouse hepatocytes and hepatomas

NASA Astrophysics Data System (ADS)

Andoh, Yoshimichi; Aoki, Noriyuki; Okazaki, Susumu

2016-02-01

Molecular dynamics (MD) calculations of lipid bilayers modeling the plasma membranes of normal mouse hepatocytes and hepatomas in water have been performed under physiological isothermal-isobaric conditions (310.15 K and 1 atm). The changes in the membrane properties induced by hepatic canceration were investigated and were compared with previous MD calculations included in our previous study of the changes in membrane properties induced by murine thymic canceration. The calculated model membranes for normal hepatocytes and hepatomas comprised 23 and 24 kinds of lipids, respectively. These included phosphatidylcholine, phosphatidylethanolamine, phosphatidylserine, phosphatidylinositol, sphingomyelin, lysophospholipids, and cholesterol. We referred to previously published experimental values for the mole fraction of the lipids adopted in the present calculations. The calculated structural and dynamic properties of the membranes such as lateral structure, order parameters, lateral self-diffusion constants, and rotational correlation times all showed that hepatic canceration causes plasma membranes to become more ordered laterally and less fluid. Interestingly, this finding contrasts with the less ordered structure and increased fluidity of plasma membranes induced by thymic canceration observed in our previous MD study.

Margins Associated with Loss of Assured Safety for Systems with Multiple Time-Dependent Failure Modes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helton, Jon C.; Brooks, Dusty Marie; Sallaberry, Cedric Jean-Marie.

Representations for margins associated with loss of assured safety (LOAS) for weak link (WL)/strong link (SL) systems involving multiple time-dependent failure modes are developed. The following topics are described: (i) defining properties for WLs and SLs, (ii) background on cumulative distribution functions (CDFs) for link failure time, link property value at link failure, and time at which LOAS occurs, (iii) CDFs for failure time margins defined by (time at which SL system fails) – (time at which WL system fails), (iv) CDFs for SL system property values at LOAS, (v) CDFs for WL/SL property value margins defined by (property valuemore » at which SL system fails) – (property value at which WL system fails), and (vi) CDFs for SL property value margins defined by (property value of failing SL at time of SL system failure) – (property value of this SL at time of WL system failure). Included in this presentation is a demonstration of a verification strategy based on defining and approximating the indicated margin results with (i) procedures based on formal integral representations and associated quadrature approximations and (ii) procedures based on algorithms for sampling-based approximations.« less

Comparing and transforming PROMIS utility values to the EQ-5D.

PubMed

Hartman, John D; Craig, Benjamin M

2018-03-01

Summarizing patient-reported outcomes (PROs) on a quality-adjusted life year (QALY) scale is an essential component to any economic evaluation comparing alternative medical treatments. While multiple studies have compared PRO items and instruments based on their psychometric properties, no study has compared the preference-based summary of the EQ-5D-3L and Patient Reported Outcomes Measurement Information System (PROMIS-29) instruments. As part of this comparison, a major aim of this manuscript is to transform PROMIS-29 utility values to an EQ-5D-3L scale. A nationally representative survey of 2623 US adults completed the 29-item PROMIS health profile instrument (PROMIS-29) and the 3-level version of the EQ-5D instrument (EQ-5D-3L). Their responses were summarized on a health utility scale using published estimates. Using regression analysis, PROMIS-29 and EQ-5D-3L utility weights were compared with each other as well as with self-reported general health. PROMIS-29 utility weights were much lower than the EQ-5D-3L weights. However, a correlation coefficient of 0.769 between the utility values of the two instruments suggests that the main discordance is simply a difference in scale between the measures. It is also possible to map PROMIS-29 utility weights onto an EQ-5D-3L scale. EQ-5D-3L losses equal .1784 × (PROMIS-29 Losses) .7286 . The published estimates of the PROMIS-29 produce lower utility values than many other health instruments. Mapping the PROMIS-29 estimates to an EQ-5D-3L scale alleviates this issue and allows for a more straightforward comparison between the PROMIS-29 and other common health instruments.

26 CFR 20.2032A-4 - Method of valuing farm real property.

Code of Federal Regulations, 2012 CFR

2012-04-01

... property types. Only rentals from tracts of comparable farm property which are rented solely for an amount... affects efficient management and use of property and value per se; and (10) Availability of, and type of... 26 Internal Revenue 14 2012-04-01 2012-04-01 false Method of valuing farm real property. 20.2032A...

26 CFR 20.2032A-4 - Method of valuing farm real property.

Code of Federal Regulations, 2013 CFR

2013-04-01

... property types. Only rentals from tracts of comparable farm property which are rented solely for an amount... affects efficient management and use of property and value per se; and (10) Availability of, and type of... 26 Internal Revenue 14 2013-04-01 2013-04-01 false Method of valuing farm real property. 20.2032A...

Relations of principal components analysis site scores to algal-biomass, habitat, basin-characteristics, nutrient, and biological-community data in the Upper Wabash River Basin, Indiana, 2003

USGS Publications Warehouse

Leer, Donald R.; Caskey, Brian J.; Frey, Jeffrey W.; Lowe, B. Scott

2007-01-01

The values for nutrients (nitrate, total Kjeldahl nitrogen, total nitrogen, and total phosphorus) and chlorophyll a (periphyton and seston) were compared to published U.S. Environmental Protection Agency (USEPA) values for Aggregate Nutrient Ecoregions VI and VII and USEPA Level III Ecoregions 55 and 56. Several nutrient values were greater than the 25th percentile of the published USEPA values. Chlorophyll a (periphyton and seston) values either were greater than the 25th percentile of published USEPA values or extended data ranges in the Aggregate Nutrient and Level III Ecoregions. If the proposed values for the 25th percentile were adopted as nutrient water-quality criteria, many samples in the Upper Wabash River Basin would have exceeded the criteria.

Transforming EQ-5D utilities for use in cost–value analysis of health programs.

PubMed

Nord, Erik; Johansen, Rune

2015-04-01

In a number of jurisdictions there is increasing interest in incorporating concerns for fairness in models for economic evaluation of health interventions. Cost–value analysis is a name for evaluations with such a broader aim. The most widely held concern for fairness is a concern for the worse off, i.e. the idea that severity of illness should count in determining priorities. In economic evaluations of improvements in health-related quality of life this concern may be taken into account by replacing conventional health state utilities with societal values for health states that are characterised by strong upper end compression and decreasing marginal value of utility gains. We review evidence on the strength of concerns for the worse off--measured at the cardinal level--in 15 articles published in peer-reviewed journals in the time period 1978–2010, with reports from altogether 20 individual studies in nine different countries. We report 116 individual observations of paired comparisons of utility improvements with different start levels. Concerns for severity show up quite strongly across countries, sample types and question framings. By means of regression analyses we fit a societal value function to the data that has the property of decreasing marginal value of utility gains. Using the central tendency in the data we present two plausible transformations of EQ-5D utilities into societal values that reflect concerns for the worse off.

Suitability of E-tongue Sensors to Assess Taste-Masking of Pediatric Liquids by Different Beverages Considering Their Physico-chemical Properties.

PubMed

Immohr, Laura Isabell; Hedfeld, Claas; Lang, Artur; Pein-Hackelbusch, Miriam

2017-02-01

Manipulation of liquid oral drugs by mixing them into foodstuff is a common procedure for taste-masking of OTC pharmaceuticals when administered to children. However, the taste-masking capability of such application media is not systematically evaluated, and recommendations for suitable media are hardly published. In this study, a sensor array of commercially available and self-developed electronic tongue sensors was employed to assess the taste-masking efficiency of eight different beverages (tap water, apple juice, carrot juice, fennel tea, fruit tea, milk, cocoa, and Alete meal to drink) on the OTC pharmaceuticals Ambroxol-ratiopharm®, Cetirizin AL, and Laxoberal® by multivariate data analysis. The Euclidean distances between each pure application medium and its corresponding drug mixture were used as an indicator for the taste-masking efficiency and correlated to the physico-chemical properties of the beverages. Thus, the pH value, the viscosity, as well as the fat and sugar content of the beverages were included, whereas only the viscosity appeared to be insignificant in all cases. The sugar content as well as the fat content and pH value emerged to be a significant variable in taste-masking efficiency for some of the tested drug products. It was shown that the applied electronic tongue sensors were capable to demonstrate the impact of the physico-chemical properties of the application media on their taste-masking capacity regardless of their non-selectivity towards these characteristics.

Quantitation of the calcium and membrane binding properties of the C2 domains of dysferlin.

PubMed

Abdullah, Nazish; Padmanarayana, Murugesh; Marty, Naomi J; Johnson, Colin P

2014-01-21

Dysferlin is a large membrane protein involved in calcium-triggered resealing of the sarcolemma after injury. Although it is generally accepted that dysferlin is Ca(2+) sensitive, the Ca(2+) binding properties of dysferlin have not been characterized. In this study, we report an analysis of the Ca(2+) and membrane binding properties of all seven C2 domains of dysferlin as well as a multi-C2 domain construct. Isothermal titration calorimetry measurements indicate that all seven dysferlin C2 domains interact with Ca(2+) with a wide range of binding affinities. The C2A and C2C domains were determined to be the most sensitive, with Kd values in the tens of micromolar, whereas the C2D domain was least sensitive, with a near millimolar Kd value. Mutagenesis of C2A demonstrates the requirement for negatively charged residues in the loop regions for divalent ion binding. Furthermore, dysferlin displayed significantly lower binding affinity for the divalent cations magnesium and strontium. Measurement of a multidomain construct indicates that the solution binding affinity does not change when C2 domains are linked. Finally, sedimentation assays suggest all seven C2 domains bind lipid membranes, and that Ca(2+) enhances but is not required for interaction. This report reveals for the first time, to our knowledge, that all dysferlin domains bind Ca(2+) albeit with varying affinity and stoichiometry. Copyright © 2014 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Costs of alcohol and drug-involved crime.

PubMed

Miller, Ted R; Levy, David T; Cohen, Mark A; Cox, Kenya L C

2006-12-01

A large proportion of violent and property crimes involve alcohol or other drugs (AOD). AOD use only causes some of these crimes. This paper estimates the costs of AOD-involved and AOD-attributable crimes. Crime counts are from government statistics adjusted for underreporting. The AOD-involved portion of crime costs is estimated from inmate surveys on alcohol and illicit drug use at the time of the crime. The costs and AOD-attributable portion of AOD-involved crimes come from published studies. They include tangible medical, mental health, property loss, future earnings, public services, adjudication, and sanctioning costs, as well as the value of pain and suffering. An estimated 5.4 million violent crimes and 8 million property crimes involved AOD use in 1999. Those AOD-involved crimes cost society over 6.5 billion dollars in medical and mental health care and almost 65 billion dollars in other tangible expenses (in 1999 dollars). If the value of pain, suffering, and lost quality of life is added, AOD-involved crime costs totaled 205 billion dollars. Violent crimes accounted for more than 85% of the costs. Roughly estimated, crimes attributable to alcohol cost 84 billion dollars, more than 2 times the 38 billion dollars attributable to drugs. Although American media--news and entertainment--dwell on the links between drugs and crime, alcohol-attributable crime costs are double drug-attributable ones. Effective efforts to reduce the abuse of alcohol and illicit drugs should reduce costs associated with crime.

The changes of red blood cell viscoelasticity and sports anemia in male 24-hr ultra-marathoners.

PubMed

Liu, Che-Hung; Tseng, Yen-Fang; Lai, Jiun-I; Chen, Yin-Quan; Wang, Shih-Hao; Kao, Wei-Fong; Li, Li-Hua; Chiu, Yu-Hui; How, Chorng-Kuang; Chang, Wen-Han

2018-05-01

In endurance sports, stress, dehydration and release of chemical factors have been associated with red blood cell (RBC) alterations of structure and function, which may contribute to sports anemia, a well-observed phenomenon during long-distance running. Until now, the investigation of the changes of viscoelastic properties of RBC membrane, a decisive factor of RBC deformability to avoid hemolysis, is lacking, especially in an Oriental population. nineteen runners were prospectively recruited into our study. Hematological parameters were analyzed before and immediately after the 2015 Taipei 24H Ultra-Marathon Festival, Taiwan. Video particle tracking microrheology was used to determine viscoelastic properties of each RBC sample by calculating the dynamic elastic modulus G'(f) and the viscous modulus G″(f) at frequency f = 20 Hz. Haptoglobin, RBC count, hemoglobin, hematocrit, mean cell hemoglobin, plasma free hemoglobin and unsaturated iron-binding capacity values of the recruited runners showed a statistically significant drop in the post-race values. Blood concentration of reticulocyte and ferritin were significantly higher at post-race compared with pre-race. 15 out of the 19 runners had a concurrent change in the elastic and the viscous moduli of their RBCs. Changes in the elastic and the viscous moduli were correlated with changes in the RBC count, hemoglobin and hematocrit. Viscoelasticity properties, the elastic modulus G'(f) and the viscous modulus G″(f) of RBCs are associated with endurance exercise-induced anemia. Copyright © 2017. Published by Elsevier Taiwan LLC.

Esthetic or Functional, Saccharine or Shocking? An Editor Looks at Values in Children's Books.

ERIC Educational Resources Information Center

Giblin, James Cross

1977-01-01

Discusses artistic or esthetic, social and cultural, functional, and commercial values looked for by children's book editors in selecting and publishing manuscripts. Also reviews changes in social and cultural values as shown by children's books published in 1947, 1957, and 1967. (GT)

Effect of in situ exopolysaccharide production on physicochemical, rheological, sensory, and microstructural properties of the yogurt drink ayran: an optimization study based on fermentation kinetics.

PubMed

Yilmaz, M T; Dertli, E; Toker, O S; Tatlisu, N B; Sagdic, O; Arici, M

2015-03-01

Exopolysaccharide (EPS)-producing starter cultures are preferred for the manufacture of fermented milk products to improve rheological and technological properties. However, no clear correlation exists between EPS production and the rheological and technological properties of fermented milk products such as the yogurt drink ayran. In this study, 4 different strain conditions (EPS- and EPS+ Streptococcus thermophilus strains) were tested as a function of incubation temperature (32, 37, or 42°C) and time (2, 3, or 4 h) to determine the effect of culture type and in situ EPS production on physicochemical, rheological, sensory, and microstructural properties of ayran. Furthermore, we assessed the effect of fermentation conditions on amounts of EPS production by different EPS-producing strains during ayran production. A multifactorial design of response surface methodology was used to model linear, interaction, and quadratic effects of these variables on steady shear rheological properties of ayran samples and in situ EPS production levels. The physicochemical and microbiological characteristics of ayran samples altered depending on incubation conditions and strain selection. Steady shear tests showed that ayran samples inoculated with EPS+ strains exhibited pseudoplastic flow behavior. Production of ayran with EPS- strain (control sample) resulted in the lowest apparent viscosity values (η50), whereas those produced with the combination of 2 EPS+ strains yielded ayran with notably increased η50 values. We concluded that incubation time was the variable with the greatest effect on η50, consistency coefficient (K), and flow behavior index (n) values. In situ EPS production was also affected by these conditions during ayran fermentation in which strain-specific metabolism conditions were found to be the most important factor for EPS production. In addition, these findings correlated the amount of in situ EPS produced with the rheological properties of ayran. Scanning electron microscopy images of the samples showed differences in structural features, revealing a prominent network strand structure in the ayran samples inoculated with the admixture of 2 EPS-producing strains incubated at 37°C for 3 h. These results provide useful information for large-scale production of ayran by the dairy industry. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

26 CFR 20.2032A-4 - Method of valuing farm real property.

Code of Federal Regulations, 2014 CFR

2014-04-01

... property types. Only rentals from tracts of comparable farm property which are rented solely for an amount... affects efficient management and use of property and value per se; and (10) Availability of, and type of... 26 Internal Revenue 14 2014-04-01 2013-04-01 true Method of valuing farm real property. 20.2032A-4...

41 CFR 102-2.30 - Where and in what formats is the FMR published?

Code of Federal Regulations, 2010 CFR

2010-07-01

... formats is the FMR published? 102-2.30 Section 102-2.30 Public Contracts and Property Management Federal... published? Proposed rules are published in the Federal Register. FMR bulletins are published in looseleaf format. FMR interim and final rules are published in the following formats— (a) Federal Register under...

Quality and Business Offer Driven Selection of Web Services for Compositions

NASA Astrophysics Data System (ADS)

D'Mello, Demian Antony; Ananthanarayana, V. S.

The service composition makes use of the existing services to produce a new value added service to execute the complex business process. The service discovery finds the suitable services (candidates) for the various tasks of the composition based on the functionality. The service selection in composition assigns the best candidate for each tasks of the pre-structured composition plan based on the non-functional properties. In this paper, we propose the broker based architecture for the QoS and business offer aware Web service compositions. The broker architecture facilitates the registration of a new composite service into three different registries. The broker publishes service information into the service registry and QoS into the QoS registry. The business offers of the composite Web service are published into a separate repository called business offer (BO) registry. The broker employs the mechanism for the optimal assignment of the Web services to the individual tasks of the composition. The assignment is based on the composite service providers’s (CSP) variety of requirements defined on the QoS and business offers. The broker also computes the QoS of resulting composition and provides the useful information for the CSP to publish thier business offers.

Diagnostic Value of Run Chart Analysis: Using Likelihood Ratios to Compare Run Chart Rules on Simulated Data Series

PubMed Central

Anhøj, Jacob

2015-01-01

Run charts are widely used in healthcare improvement, but there is little consensus on how to interpret them. The primary aim of this study was to evaluate and compare the diagnostic properties of different sets of run chart rules. A run chart is a line graph of a quality measure over time. The main purpose of the run chart is to detect process improvement or process degradation, which will turn up as non-random patterns in the distribution of data points around the median. Non-random variation may be identified by simple statistical tests including the presence of unusually long runs of data points on one side of the median or if the graph crosses the median unusually few times. However, there is no general agreement on what defines “unusually long” or “unusually few”. Other tests of questionable value are frequently used as well. Three sets of run chart rules (Anhoej, Perla, and Carey rules) have been published in peer reviewed healthcare journals, but these sets differ significantly in their sensitivity and specificity to non-random variation. In this study I investigate the diagnostic values expressed by likelihood ratios of three sets of run chart rules for detection of shifts in process performance using random data series. The study concludes that the Anhoej rules have good diagnostic properties and are superior to the Perla and the Carey rules. PMID:25799549

Properties of a color-changeable chewing gum used to evaluate masticatory performance.

PubMed

Hama, Yohei; Kanazawa, Manabu; Minakuchi, Shunsuke; Uchida, Tatsuro; Sasaki, Yoshiyuki

2014-04-01

To clarify the basic properties of a color-changeable chewing gum to determine its applicability to evaluations of masticatory performance under different types of dental status. Ten participants with natural dentition aged 26-30 years chewed gum that changes color during several chewing strokes over five repetitions. Changes in color were assessed using a colorimeter, and then L*, a*, and b* values in the CIELAB color system were quantified. Relationships between chewing progression and color changes were assessed using regression analysis and the reliability of color changes was assessed using intraclass correlation coefficients. We then measured 42 dentate participants (age, 22-31 years) and 47 complete denture wearers (age, 44-90 years) to determine the detectability of masticatory performance under two types of dental status. Regression between the number of chewing strokes and the difference between two colors was non-linear. The intraclass correlation coefficients were highest between 60 and 160 chewing strokes. Dentate and edentulous groups significantly differed (Wilcoxon rank sum test) and values were widely distributed within each group. The color of the chewing gum changed over a wide range, which was sufficient to evaluate the masticatory performance of individuals with natural dentition and those with complete dentures. Changes in the color values of the gum reliably reflected masticatory performance. These findings indicate that the color-changeable chewing gum will be useful for evaluating masticatory performance under any dental status. Copyright © 2014 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Tabulated Transmissivity and Storage Properties of the Floridan Aquifer System in Florida and Parts of Georgia, South Carolina, and Alabama

USGS Publications Warehouse

Kuniansky, Eve L.; Bellino, Jason C.

2012-04-19

A goal of the U.S. Geological Survey Groundwater Resources Program is to assess the availability of fresh water within each of the principal aquifers in the United States with the greatest groundwater withdrawals. The Floridan aquifer system (FAS), which covers an area of approximately 100,000 square miles in Florida and parts of Georgia, Alabama, Mississippi, and South Carolina, is one such principal aquifer, having the fifth largest groundwater withdrawals in the Nation, totaling 3.64 billion gallons per day in 2000. Compilation of FAS hydraulic properties is critical to the development and calibration of groundwater flow models that can be used to develop water budgets spatially and temporally, as well as to evaluate resource changes over time. Wells with aquifer test data were identified as Upper Floridan aquifer (UFA), Lower Floridan aquifer (LFA), Floridan aquifer system (FAS, Upper Floridan with some middle and/or Lower Floridan), or middle Floridan confining unit (MCU), based on the identification from the original database or report description, or comparison of the open interval of the well with previously published maps.This report consolidates aquifer hydraulic property data obtained from multiple databases and reports of the U.S. Geological Survey, various State agencies, and the Water Management Districts of Florida, that are compiled into tables to provide a single information source for transmissivity and storage properties of the FAS as of October 2011. Transmissivity calculated from aquifer pumping tests and specific-capacity data are included. Values for transmissivity and storage coefficients are intended for use in regional or sub regional groundwater flow models; thus, any tests (aquifer pumping tests and specific capacity data) that were conducted with packers or for open intervals less than 30 feet in length are excluded from the summary statistics and tables of this report, but are included in the database.The transmissivity distribution from the aquifer pumping tests is highly variable. The transmissivity based on aquifer pumping tests (from 1,045 values for the UFA and FAS) ranges from 8 to about 9,300,000 square feet per day (ft2/d) and values of storage coefficient (646 reported) range from 3x10-9 to 0.41. The 64 transmissivity values for the LFA range from about 130 to 4,500,000 ft2/d, and the 17 storage coefficient values range from 7x10-8 to 0.03. The 14 transmissivity values for the MCU range from 1 to about 600,000 ft2/d and the 10 storage coefficient values range from 8x10-8 to 0.03. Transmissivity estimates for the UFA and FAS for 442 specific capacity tests range from approximately 200 to 1,000,000 ft2/d.

Mechanical and corrosion properties of newly developed biodegradable Zn-based alloys for bone fixation.

PubMed

Vojtěch, D; Kubásek, J; Serák, J; Novák, P

2011-09-01

In the present work Zn-Mg alloys containing up to 3wt.% Mg were studied as potential biodegradable materials for medical use. The structure, mechanical properties and corrosion behavior of these alloys were investigated and compared with those of pure Mg, AZ91HP and casting Zn-Al-Cu alloys. The structures were examined by light and scanning electron microscopy (SEM), and tensile and hardness testing were used to characterize the mechanical properties of the alloys. The corrosion behavior of the materials in simulated body fluid with pH values of 5, 7 and 10 was determined by immersion tests, potentiodynamic measurements and by monitoring the pH value evolution during corrosion. The surfaces of the corroded alloys were investigated by SEM, energy-dispersive spectrometry and X-ray photoelectron spectroscopy. It was found that a maximum strength and elongation of 150MPa and 2%, respectively, were achieved at Mg contents of approximately 1wt.%. These mechanical properties are discussed in relation to the structural features of the alloys. The corrosion rates of the Zn-Mg alloys were determined to be significantly lower than those of Mg and AZ91HP alloys. The former alloys corroded at rates of the order of tens of microns per year, whereas the corrosion rates of the latter were of the order of hundreds of microns per year. Possible zinc doses and toxicity were estimated from the corrosion behavior of the zinc alloys. It was found that these doses are negligible compared with the tolerable biological daily limit of zinc. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Global direct radiative forcing by process-parameterized aerosol optical properties

NASA Astrophysics Data System (ADS)

KirkevâG, Alf; Iversen, Trond

2002-10-01

A parameterization of aerosol optical parameters is developed and implemented in an extended version of the community climate model version 3.2 (CCM3) of the U.S. National Center for Atmospheric Research. Direct radiative forcing (DRF) by monthly averaged calculated concentrations of non-sea-salt sulfate and black carbon (BC) is estimated. Inputs are production-specific BC and sulfate from [2002] and background aerosol size distribution and composition. The scheme interpolates between tabulated values to obtain the aerosol single scattering albedo, asymmetry factor, extinction coefficient, and specific extinction coefficient. The tables are constructed by full calculations of optical properties for an array of aerosol input values, for which size-distributed aerosol properties are estimated from theory for condensation and Brownian coagulation, assumed distribution of cloud-droplet residuals from aqueous phase oxidation, and prescribed properties of the background aerosols. Humidity swelling is estimated from the Köhler equation, and Mie calculations finally yield spectrally resolved aerosol optical parameters for 13 solar bands. The scheme is shown to give excellent agreement with nonparameterized DRF calculations for a wide range of situations. Using IPCC emission scenarios for the years 2000 and 2100, calculations with an atmospheric global cliamte model (AFCM) yield a global net anthropogenic DRF of -0.11 and 0.11 W m-2, respectively, when 90% of BC from biomass burning is assumed anthropogenic. In the 2000 scenario, the individual DRF due to sulfate and BC has separately been estimated to -0.29 and 0.19 W m-2, respectively. Our estimates of DRF by BC per BC mass burden are lower than earlier published estimates. Some sensitivity tests are included to investigate to what extent uncertain assumptions may influence these results.

Performance Assessment Tools for Distance Learning and Simulation: Knowledge, Models and Tools to Improve the Effectiveness of Naval Distance Learning

DTIC Science & Technology

2006-06-01

34/> <!-- someapplet.imi -- > <property narne="appletcontent"’ value="somecontent jar"!> <!- - someapplet.lml -- > <property narne="jnlpcodebasedir" value= gizmo "!> gizmo ...property name="jnlphref"’ value="gizmo.jnlp",’> 0!- - gizmo.jnlp -- > <property narne="jnlptitle"’ value="Nifty Gizmo !/> <!-- nifty gizmo

Diagnostic Value of Elastography in the Diagnosis of Intermetatarsal Neuroma.

PubMed

Ormeci, Tugrul; Güler, Olcay; Malkoc, Melih; Keskinbora, Mert; Güngören, Fatma Zeynep; Mahirogulları, Mahir

2016-01-01

The objective of the present study was to characterize the ultrasound and elastographic properties of intermetatarsal neuroma (interdigital neuroma) and their contribution to diagnosis. Eighteen patients with metatarsalgia, who had presented to an orthopedic clinic from April 2013 to February 2015, were diagnosed with 25 intermetatarsal neuromas (11 unilateral [61.11%], 7 bilateral [38.89%]). These patients underwent evaluation with ultrasonography and simultaneous ultrasound strain elastography to assess the elastographic properties of the tissues in the intermetatarsal space. The intermetatarsal neuroma diagnosis was confirmed by histopathologic inspection. The lesion contours, localization, dimensions, and vascularization were evaluated before surgical excision. The elasticity and strain ratio values were compared between the neuroma and adjacent healthy intermetatarsal space. Of the 25 intermetatarsal neuromas, 1 (4%) was not detected by ultrasonography (incidence of detection of 96%). The mean neuroma width was 6.35 (range 3.7 to 13) mm in the coronal plane, and the mean elasticity and strain ratio values were 3.44 (range 1.1 to 5.1) and 9.47 (range 2.3 to 19.3), respectively. The elasticity and strain ratio values were significantly greater in the presence of an interdigital neuroma than in the adjacent healthy intermetatarsal spaces (Z = -3.964, p = .0001 and Z = -3.927, p = .0001, respectively). The diagnostic cutoff values were calculated as 2.52 for elasticity and 6.1 for the strain ratio. Four neuromas (16%) were not demarcated, and the elasticity and strain ratio values for these were lower than those for neuromas with demarcated contours but were greater than those for healthy intermetatarsal spaces (p < .006 and p < .005, respectively). Patients with clinically suspected intermetatarsal neuromas that do not show demarcation and with smaller lesions might benefit from the use of ultrasound elastography for diagnosis. Copyright © 2016 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Dosimetric properties of a Solid Water High Equivalency (SW557) phantom for megavoltage photon beams.

PubMed

Araki, Fujio

2017-07-01

The dosimetric properties of the recently developed SW557 phantom have been investigated by comparison with those of the existing SW457 phantom in megavoltage photon beams. The electron fluence ratio φ pl w , and chamber ionization ratio k pl , of water to SW457 and water to SW557 for 4-15MV photons were calculated as a function of depth using Monte Carlo simulations, and compared with measured values. Values of φ pl w for SW457 were in the range of 1.004-1.014 for 4MV, and 1.014-1.018 for 15MV photons. The φ pl w for SW557 ranged from 1.005 to 1.008 for 4MV and from 1.010 to 1.015 for 15MV photons and the variation of φ pl w with depth for each beam energy was within ±0.5%. Values of k pl were obtained with a PTW 30013 Farmer-type ionization chamber. The k pl for SW457 ranged from 0.997 to 1.011 for 4-15MV photons. Values of k pl for SW557 were almost unity for 4 and 6MV photons, while in the case of 10 and 15MV photons they were less than 1.006, excepting the build-up region. The measured and calculated k pl values of water to SW557 were in the range of 0.997-1.002 and 1.000-1.006, respectively, for 4-15MV photons, at a depth of 10cm with a source-to-axis distance of 100cm. The measured and calculated k pl values were in agreement within their uncertainty ranges. As a water-equivalent phantom, SW557 can be used with a dosimetric difference within±0.6%, for 4-15MV photons, and is more water-equivalent than SW457 in megavoltage photon beams. Copyright © 2017 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

78 FR 1305 - Agency Information Collection Activities: Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-08

... value of the property is recorded in accordance with generally accepted accounting principles (GAAP... is necessary. In addition, a bank must value off-lease property at the lower of current fair market value or book value promptly after the property comes off- [[Page 1306

Variation in flexural properties of photo-pultruded composite archwires: analyses of round and rectangular profiles.

PubMed

Fallis, D W; Kusy, R P

2000-11-01

Prototype continuous, unidirectional, fiber-reinforced composite archwires were manufactured into round and rectangular profiles utilizing a photo-pultrusion process. Both 0.022 inch (0.56 mm) diameter and 0.021 x 0.028 inch (0.53 x 0.71 mm) rectangular composites were formed utilizing commercially available S2-glass reinforcement within a polymeric matrix. Reinforcement was varied according to the number, denier and twists per inch (TPI) of four S2-glass yarns to volume levels of 32-74% for round and 41-61% for rectangular profiles. Cross-sectional geometry was evaluated via light microscopy to determine loading characteristics; whereas two flexural properties (the elastic moduli and flexural strengths) were determined by 3-point bending tests. Morphological evaluation of samples revealed that as the TPI increased from 1 to 8, the yarns were more separated from one another and distributed more peripherally within a profile. For round and rectangular profiles utilizing 1 TPI fibers, moduli increased with fiber content approaching theoretical values. For round profiles utilizing 1 TPI and 4 TPI fibers, flexural strengths increased until the loading geometry was optimized. In contrast, the flexural strengths of composites that were pultruded with 8 TPI fibers were not improved at any loading level. Doubling the denier of the yarn, without altering the loading, increased both the moduli and flexural strengths in rectangular samples; whereas, the increases observed in round samples were not statistically significant. At optimal loading the maximum mean moduli and strengths equaled 53.6 +/- 2.0 and 1.36 +/- 0.17 GPa for round wire and equaled 45.7 +/- 0.8 and 1.40 +/- 0.05 GPa for rectangular wires, respectively. These moduli were midway between that of martensitic NiTi (33.4 GPa) and beta-titanium (72.4 GPa), and produced about one-quarter the force of a stainless steel wire per unit of activation. Values of strengths placed this composite material in the range of published values for beta-titanium wires (1.3-1.5 GPa). Copyright 2000 Kluwer Academic Publishers

The impact of capillary backpressure on spontaneous counter-current imbibition in porous media

NASA Astrophysics Data System (ADS)

Foley, Amir Y.; Nooruddin, Hasan A.; Blunt, Martin J.

2017-09-01

We investigate the impact of capillary backpressure on spontaneous counter-current imbibition. For such displacements in strongly water-wet systems, the non-wetting phase is forced out through the inlet boundary as the wetting phase imbibes into the rock, creating a finite capillary backpressure. Under the assumption that capillary backpressure depends on the water saturation applied at the inlet boundary of the porous medium, its impact is determined using the continuum modelling approach by varying the imposed inlet saturation in the analytical solution. We present analytical solutions for the one-dimensional incompressible horizontal displacement of a non-wetting phase by a wetting phase in a porous medium. There exists an inlet saturation value above which any change in capillary backpressure has a negligible impact on the solutions. Above this threshold value, imbibition rates and front positions are largely invariant. A method for identifying this inlet saturation is proposed using an analytical procedure and we explore how varying multiphase flow properties affects the analytical solutions and this threshold saturation. We show the value of this analytical approach through the analysis of previously published experimental data.

Development and application of a hillslope hydrologic model

USGS Publications Warehouse

Blain, C.A.; Milly, P.C.D.

1991-01-01

A vertically integrated two-dimensional lateral flow model of soil moisture has been developed. Derivation of the governing equation is based on a physical interpretation of hillslope processes. The lateral subsurface-flow model permits variability of precipitation and evapotranspiration, and allows arbitrary specification of soil-moisture retention properties. Variable slope, soil thickness, and saturation are all accommodated. The numerical solution method, a Crank-Nicolson, finite-difference, upstream-weighted scheme, is simple and robust. A small catchment in northeastern Kansas is the subject of an application of the lateral subsurface-flow model. Calibration of the model using observed discharge provides estimates of the active porosity (0.1 cm3/cm3) and of the saturated horizontal hydraulic conductivity (40 cm/hr). The latter figure is at least an order of magnitude greater than the vertical hydraulic conductivity associated with the silty clay loam soil matrix. The large value of hydraulic conductivity derived from the calibration is suggestive of macropore-dominated hillslope drainage. The corresponding value of active porosity agrees well with a published average value of the difference between total porosity and field capacity for a silty clay loam. ?? 1991.

Photoelectron spectroscopic studies of 5-halouracil anions

PubMed Central

Radisic, Dunja; Ko, Yeon Jae; Nilles, John M.; Stokes, Sarah T.; Sevilla, Michael D.; Rak, Janusz; Bowen, Kit H.

2011-01-01

The parent negative ions of 5-chlorouracil, UCl− and 5-fluorouracil, UF− have been studied using anion photoelectron spectroscopy in order to investigate the electrophilic properties of their corresponding neutral halouracils. The vertical detachment energies (VDE) of these anions and the adiabatic electron affinities (EA) of their neutral molecular counterparts are reported. These results are in good agreement with the results of previously published theoretical calculations. The VDE values for both UCl− and UF− and the EA values for their neutral molecular counterparts are much greater than the corresponding values for both anionic and neutral forms of canonical uracil and thymine. These results are consistent with the observation that DNA is more sensitive to radiation damage when thymine is replaced by halouracil. While we also attempted to prepare the parent anion of 5-bromouracil, UBr−, we did not observe it, the mass spectrum exhibiting only Br− fragments, i.e., 5-bromouracil apparently underwent dissociative electron attachment. This observation is consistent with a previous assessment, suggesting that 5-bromouracil is the best radio-sensitizer among these three halo-nucleobases. PMID:21219027

Reexamination of the ORAC assay: effect of metal ions.

PubMed

Nkhili, E; Brat, P

2011-05-01

The oxygen radical absorbance capacity (ORAC) assay method has been employed extensively in the field of antioxidant and oxidative stress. It uses fluorescein as probe for oxidation by peroxyl radical. Hundreds of reports have been published on the use of this method to determine antioxidant capacity in food and biological samples. The question is whether the results of all these reports are influenced by antioxidant autoxidation, which occurs during the ORAC test. Indeed, the presence of metal ions in the studied matrix will influence antioxidant stability, thereby leading to the underestimation of their antioxidant properties. Ethylenediaminetetraacetic acid hydrate (EDTA) can be used as a metal complexation agent. This paper examines the effect of the addition of EDTA on the ORAC values of pure compounds (quercetin, ascorbic, and dehydroascorbic acid) and five food juices (kiwi, orange, tomato, red grape, and apple). Metal complexation by EDTA (80 μM) clearly increased the ORAC values, given that the antioxidant was protected against rapid autoxidation incited by trace metal ions within samples and then by free radicals. Our finding also undoubtedly demonstrated that the number of literature values is potentially underestimated.

Surface complexation modeling of americium sorption onto volcanic tuff.

PubMed

Ding, M; Kelkar, S; Meijer, A

2014-10-01

Results of a surface complexation model (SCM) for americium sorption on volcanic rocks (devitrified and zeolitic tuff) are presented. The model was developed using PHREEQC and based on laboratory data for americium sorption on quartz. Available data for sorption of americium on quartz as a function of pH in dilute groundwater can be modeled with two surface reactions involving an americium sulfate and an americium carbonate complex. It was assumed in applying the model to volcanic rocks from Yucca Mountain, that the surface properties of volcanic rocks can be represented by a quartz surface. Using groundwaters compositionally representative of Yucca Mountain, americium sorption distribution coefficient (Kd, L/Kg) values were calculated as function of pH. These Kd values are close to the experimentally determined Kd values for americium sorption on volcanic rocks, decreasing with increasing pH in the pH range from 7 to 9. The surface complexation constants, derived in this study, allow prediction of sorption of americium in a natural complex system, taking into account the inherent uncertainty associated with geochemical conditions that occur along transport pathways. Published by Elsevier Ltd.

Masking properties of ceramics for veneer restorations.

PubMed

Skyllouriotis, Andreas L; Yamamoto, Hideo L; Nathanson, Dan

2017-10-01

The translucency and opacity of ceramics play a significant role in emulating the natural color of teeth, but studies of the masking properties and limitations of dental ceramics when used as monolayer restorations are lacking. The purpose of this in vitro study was to determine the translucency of 6 materials used for veneer restorations by assessing their translucency parameters (TPs), contrast ratios (CRs), and potential to mask dark tooth colors. Ten square- or disk-shaped specimens (0.5-mm thickness, shade A2) were fabricated from Vitablocks Mark II (VMII; Vita Zahnfabrik), IPS e.max CAD LT (EMXC LT; Ivoclar Vivadent AG), IPS e.max CAD HT (EMXC HT; Ivoclar Vivadent AG), IPS Empress CAD LT (EMP LT; Ivoclar Vivadent AG), IPS e.max Press LT (EMXP LT; Ivoclar Vivadent AG), and CZR (CZR; Kuraray Noritake Dental Inc). Their luminance (Y) values over black and over white tiles were measured, followed by their color (CIELab) over black tiles and white tiles and shaded A2 (control group), A3.5, A4, and B4 acrylic resin blocks. All measurements were performed using a spectrophotometer in 2 different areas on each specimen. Then CRs, TPs, and color differences (over shaded backgrounds) were determined. Data were subjected to 1-way and 2-way ANOVA (α=.05) for analysis. Mean CR values of EMXP LT were significantly higher than those of the other tested materials, whereas VMII and EMXC HT had the lowest values (P<.001). Mean TP values over black and over white backgrounds of VMII and EMXC HT were significantly higher than those of the other tested materials, while EMXP LT and EMXC LT revealed the lowest values (P<.001). Background shade A4 displayed the highest mean effect (expressed in ΔE* values) on the color of the ceramic materials, whereas shade B4 demonstrated the lowest mean background effect (P<.001). Significant differences in translucency among the tested ceramics were revealed (P<.001). The EMXC LT and EMXP LT groups were the least translucent under the conditions of this study (P<.001). All tested ceramics exhibited poor masking properties against the A4 background. The color differences of most tested ceramics were more acceptable when tested against the B4 background (ΔE*≤3.3). Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Predicting bioactive glass properties from the molecular chemical composition: glass transition temperature.

PubMed

O'Donnell, Matthew D

2011-05-01

The glass transition temperature (T(g)) of inorganic glasses is an important parameter than can be used to correlate with other glass properties, such as dissolution rate, which governs in vitro and in vivo bioactivity. Seven bioactive glass compositional series reported in the literature (77 in total) were analysed here with T(g) values obtained by a number of different methods: differential thermal analysis, differential scanning calorimetry and dilatometry. An iterative least-squares fitting method was used to correlate T(g) from thermal analysis of these compositions with the levels of individual oxide and fluoride components in the glasses. When all seven series were fitted a reasonable correlation was found between calculated and experimental values (R(2)=0.89). When the two compositional series that were designed in weight percentages (the remaining five were designed in molar percentage) were removed from the model an improved fit was achieved (R(2)=0.97). This study shows that T(g) for a wide range in compositions (e.g. SiO(2) content of 37.3-68.4 mol.%) can be predicted to reasonable accuracy enabling processing parameters to be predicted such as annealing, fibre-drawing and sintering temperatures. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Design and validation of an oral health questionnaire for preoperative anaesthetic evaluation.

PubMed

Ruíz-López Del Prado, Gema; Blaya-Nováková, Vendula; Saz-Parkinson, Zuleika; Álvarez-Montero, Óscar Luis; Ayala, Alba; Muñoz-Moreno, Maria Fe; Forjaz, Maria João

Dental injuries incurred during endotracheal intubation are more frequent in patients with previous oral pathology. The study objectives were to develop an oral health questionnaire for preanaesthesia evaluation, easy to apply for personnel without special dental training; and establish a cut-off value for detecting persons with poor oral health. Validation study of a self-administered questionnaire, designed according to a literature review and an expert group's recommendations. The questionnaire was applied to a sample of patients evaluated in a preanaesthesia consultation. Rasch analysis of the questionnaire psychometric properties included viability, acceptability, content validity and reliability of the scale. The sample included 115 individuals, 50.4% of men, with a median age of 58 years (range: 38-71). The final analysis of 11 items presented a Person Separation Index of 0.861 and good adjustment of data to the Rasch model. The scale was unidimensional and its items were not biased by sex, age or nationality. The oral health linear measure presented good construct validity. The cut-off value was set at 52 points. The questionnaire showed sufficient psychometric properties to be considered a reliable tool, valid for measuring the state of oral health in preoperative anaesthetic evaluations. Copyright © 2016 Sociedade Brasileira de Anestesiologia. Published by Elsevier Editora Ltda. All rights reserved.

Many-body ab initio diffusion quantum Monte Carlo applied to the strongly correlated oxide NiO

DOE PAGES

Mitra, Chandrima; Krogel, Jaron T.; Santana, Juan A.; ...

2015-10-28

We present a many-body diffusion quantum Monte Carlo (DMC) study of the bulk and defect properties of NiO. We find excellent agreement with experimental values, within 0.3%, 0.6%, and 3.5% for the lattice constant, cohesive energy, and bulk modulus, respectively. The quasiparticle bandgap was also computed, and the DMC result of 4.72 (0.17) eV compares well with the experimental value of 4.3 eV. Furthermore, DMC calculations of excited states at the L, Z, and the gamma point of the Brillouin zone reveal a flat upper valence band for NiO, in good agreement with Angle Resolved Photoemission Spectroscopy results. To studymore » defect properties, we evaluated the formation energies of the neutral and charged vacancies of oxygen and nickel in NiO. A formation energy of 7.2 (0.15) eV was found for the oxygen vacancy under oxygen rich conditions. For the Ni vacancy, we obtained a formation energy of 3.2 (0.15) eV under Ni rich conditions. Lastly, these results confirm that NiO occurs as a p-type material with the dominant intrinsic vacancy defect being Ni vacancy. (C) 2015 AIP Publishing LLC.« less

Optimization of scaffold design for bone tissue engineering: A computational and experimental study.

PubMed

Dias, Marta R; Guedes, José M; Flanagan, Colleen L; Hollister, Scott J; Fernandes, Paulo R

2014-04-01

In bone tissue engineering, the scaffold has not only to allow the diffusion of cells, nutrients and oxygen but also provide adequate mechanical support. One way to ensure the scaffold has the right properties is to use computational tools to design such a scaffold coupled with additive manufacturing to build the scaffolds to the resulting optimized design specifications. In this study a topology optimization algorithm is proposed as a technique to design scaffolds that meet specific requirements for mass transport and mechanical load bearing. Several micro-structures obtained computationally are presented. Designed scaffolds were then built using selective laser sintering and the actual features of the fabricated scaffolds were measured and compared to the designed values. It was possible to obtain scaffolds with an internal geometry that reasonably matched the computational design (within 14% of porosity target, 40% for strut size and 55% for throat size in the building direction and 15% for strut size and 17% for throat size perpendicular to the building direction). These results support the use of these kind of computational algorithms to design optimized scaffolds with specific target properties and confirm the value of these techniques for bone tissue engineering. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Virtual milk for modelling and simulation of dairy processes.

PubMed

Munir, M T; Zhang, Y; Yu, W; Wilson, D I; Young, B R

2016-05-01

The modeling of dairy processing using a generic process simulator suffers from shortcomings, given that many simulators do not contain milk components in their component libraries. Recently, pseudo-milk components for a commercial process simulator were proposed for simulation and the current work extends this pseudo-milk concept by studying the effect of both total milk solids and temperature on key physical properties such as thermal conductivity, density, viscosity, and heat capacity. This paper also uses expanded fluid and power law models to predict milk viscosity over the temperature range from 4 to 75°C and develops a succinct regressed model for heat capacity as a function of temperature and fat composition. The pseudo-milk was validated by comparing the simulated and actual values of the physical properties of milk. The milk thermal conductivity, density, viscosity, and heat capacity showed differences of less than 2, 4, 3, and 1.5%, respectively, between the simulated results and actual values. This work extends the capabilities of the previously proposed pseudo-milk and of a process simulator to model dairy processes, processing different types of milk (e.g., whole milk, skim milk, and concentrated milk) with different intrinsic compositions, and to predict correct material and energy balances for dairy processes. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Cut-off proposal for the detection of ketamine in hair.

PubMed

Salomone, A; Gerace, E; Diana, P; Romeo, M; Malvaso, V; Di Corcia, D; Vincenti, M

2015-03-01

Ketamine is a powerful anesthetic drug used in both human and veterinary surgery, but it is also commonly misused because of its psychotropic properties. Since the abuse of this drug has been reported in many countries worldwide, its determination in hair samples is offered as a specialist test by hundreds of laboratories. However, unlike other common drugs of abuse, a cut-off level for ketamine in hair has not been fixed yet. Therefore, aim of this study is to propose a concentration value for ketamine in hair analysis, in order to discriminate between chronic and occasional use, and between active use and external contamination. After considering the chemical properties of this molecule, and the experimental data collected in our laboratory or reported in several other published studies, we propose a cut-off level of 0.5ng/mg, as indicative of repeated exposure to ketamine. Additionally, we suggest that the detection of the metabolite norketamine should be mandatory to prove active intake and exclude false positive result from external contamination. Thus, a reasonable cut-off value for norketamine could be fixed at 0.1ng/mg, while the minimal concentration ratio norketamine/ketamine may be positively established at 0.05. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Chemical composition and physical properties of filter fly ashes from eight grate-fired biomass combustion plants.

PubMed

Lanzerstorfer, Christof

2015-04-01

For the handling, treatment and utilization of fly ash from biomass combustion its chemical composition and physical properties are important. In this study eight filter fly ashes from different grate-fired biomass combustion plants were investigated. In fly ash from straw combustion high concentrations of (K) were found, whereas in the fly ash from wood combustion the concentrations of Ca and Mg were higher. The average concentration of PO4(3-) was similar in both types of fly ashes. In all wood fly ashes some measured heavy metal concentrations were above the limits for utilization. The straw fly ashes were much less contaminated and can be utilized. For wood fly ash most parameters showed little variation, except from one fly ash where the dust pre-separator is in poor condition. The average values were: mass median diameter 4.3±0.8 μm, spread of particle size distribution 19±11, particle density 2620±80 kg/m3 and angle of repose 50°±1°. The density of the straw fly ashes is lower (2260±80 kg/m3) and the spread of the size distribution is higher (72±24). For one straw combustion fly ash the values of the mass median diameter and the angle of repose were similar to the values of wood combustion fly ash, for the other straw fly ash the values differed considerably. While the particle size of this fly ash was much smaller, surprisingly the angle of repose was also lower. This can be attributed to the formation of small agglomerates in this fly ash, which were not disintegrated without a certain stress. Copyright © 2015. Published by Elsevier B.V.

Effect of Dioscorea opposita Thunb. (yam) supplementation on physicochemical and sensory characteristics of yogurt.

PubMed

Kim, S H; Lee, S Y; Palanivel, G; Kwak, H S

2011-04-01

A study was conducted to examine the physicochemical, microbial, and sensory properties of yogurt made by supplementing powdered yam Dioscorea opposita Thunb. (YPT) at different concentrations (0.2, 0.4, 0.6, and 0.8%, wt/vol) into milk, which was pasteurized and then fermented at 43°C for 6 h and stored for 16 d. The pH values of all samples decreased, whereas viscosity values and mean microbial counts increased during storage. The L* and a* color values (indicators of lightness and redness, respectively) of yogurt samples were not remarkably influenced by adding YPT, whereas the b* values (indicating yellowness) significantly increased with the addition of YPT at all concentrations at 0 d of storage, probably due to the original yellow color of yam powder. In functional component analyses, when the concentration of YPT increased, the amount of allantoin and diosgenin proportionally increased. The content of allantoin was 3.22 and diosgenin 4.69 μg/mL when 0.2% (wt/vol) YPT was supplemented and did not change quantitatively during the storage period (16 d). The sensory test revealed that the overall acceptability scores of YPT-supplemented yogurt samples (0.2 to 0.6%, wt/vol) were quite similar to those of the control throughout the storage period of 16 d. Based on the data obtained from the present study, it was concluded that the concentrations (0.2 to 0.6%, wt/vol) of YPT could be used to produce YPT-supplemented yogurt without significant adverse effects on physicochemical, microbial, and sensory properties, and enhance functional components from the supplementation. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Status report on microfilled composite restorative resin. Council on Dental Materials, Instruments, and Equipment.

PubMed

Dennison, J B

1982-09-01

Microfilled resins generally have physical properties inferior to those of conventional composites. A lower in organic filler content or higher polymer/filled ratio results in a lower modulus of elasticity, greater thermal dimensional change, less resistance to indentation and abrasion, and greater water sorption. The ability to finish and to maintain a smooth surface texture is a major advantage, although it has not been proved clinically that microfilled resin restorations result in less plaque adherence nor do they enhance soft tissue response. Early clinical trials, after two to three years in vivo, indicate a greater wear resistance for these materials than for conventional composites. At this time, current evidence suggests that a decrease in filler particles size to less than 1 micrometer and a lower filler loading of the resin matrix permit the clinical development and maintenance of a smooth surface texture on restoration surfaces. There is no published evidence that the decrease in many of the physical properties leads to early signs of clinical deterioration and failure. In vivo studies extended for longer periods are necessary to make a knowledgeable judgment on the true clinical value of these composites. A classification system for composite restorative resins is being prepared by the Council on Dental Materials, Instruments, and Equipment. It will be published in a future issue of The Journal.

Publishers, Publishing and the Internet: How Journal Publishing Will Survive and Prosper in the Electronic Age.

ERIC Educational Resources Information Center

Cox, John E.

1997-01-01

The Internet will change how publishers function. Publishers will need to acquire new skills in developing multimedia; become custodians of intellectual property rather than producers of printed artifacts; know copyright and contract law, especially international aspects; and work more closely with universities to deliver electronic information…

Defining and assessing wisdom: a review of the literature.

PubMed

Bangen, Katherine J; Meeks, Thomas W; Jeste, Dilip V

2013-12-01

With increasing longevity and a growing focus on successful aging, there has been a recent growth of research designed to operationalize and assess wisdom. We aimed to (1) investigate the degree of overlap among empirical definitions of wisdom, (2) identify the most commonly cited wisdom subcomponents, (3) examine the psychometric properties of existing assessment instruments, and (4) investigate whether certain assessment procedures work particularly well in tapping the essence of subcomponents of the various empirical definitions. We searched PsychINFO-indexed articles published through May 2012 and their bibliographies. Studies were included if they were published in a peer-reviewed journal and (1) proposed a definition of wisdom or (2) discussed the development or validation of an instrument designed to assess wisdom. Thirty-one articles met inclusion criteria. Despite variability among the 24 reviewed definitions, there was significant overlap. Commonly cited subcomponents of wisdom included knowledge of life, prosocial values, self-understanding, acknowledgment of uncertainty, emotional homeostasis, tolerance, openness, spirituality, and sense of humor. Published reports describing the psychometric properties of nine instruments varied in comprehensiveness but most measures were examined for selected types of reliability and validity, which were generally acceptable. Given limitations of self-report procedures, an approach integrating multiple indices (e.g., self-report and performance-based measures) may better capture wisdom. Significant progress in the empirical study of wisdom has occurred over the past four decades; however, much needs to be done. Future studies with larger, more diverse samples are needed to determine the generalizability, usefulness, and clinical applicability of these definitions and assessment instruments. Such work will have relevance for the fields of geriatrics, psychiatry, psychology, sociology, education, and public health, among others. Copyright © 2013 American Association for Geriatric Psychiatry. All rights reserved.

A numerical investigation into the influence of the properties of cobalt chrome cellular structures on the load transfer to the periprosthetic femur following total hip arthroplasty.

PubMed

Hazlehurst, Kevin Brian; Wang, Chang Jiang; Stanford, Mark

2014-04-01

Stress shielding of the periprosthetic femur following total hip arthroplasty is a problem that can promote the premature loosening of femoral stems. In order to reduce the need for revision surgery it is thought that more flexible implant designs need to be considered. In this work, the mechanical properties of laser melted square pore cobalt chrome molybdenum cellular structures have been incorporated into the design of a traditional monoblock femoral stem. The influence of incorporating the properties of cellular structures on the load transfer to the periprosthetic femur was investigated using a three dimensional finite element model. Eleven different stiffness configurations were investigated by using fully porous and functionally graded approaches. This investigation confirms that the periprosthetic stress values depend on the stiffness configuration of the stem. The numerical results showed that stress shielding is reduced in the periprosthetic Gruen zones when the mechanical properties of cobalt chrome molybdenum cellular structures are used. This work identifies that monoblock femoral stems manufactured using a laser melting process, which are designed for reduced stiffness, have the potential to contribute towards reducing stress shielding. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Guideline for translation and national validation of the Quality of Life in Hand Eczema Questionnaire (QOLHEQ).

PubMed

Oosterhaven, Jart A F; Schuttelaar, Marie L A; Apfelbacher, Christian; Diepgen, Thomas L; Ofenloch, Robert F

2017-08-01

There is a need for well-developed and validated questionnaires to measure patient reported outcomes. The Quality of Life in Hand Eczema Questionnaire (QOLHEQ) is such a validated instrument measuring disease-specific health-related quality of life in hand eczema patients. A re-validation of measurement properties is required before an instrument is used in a new population. With the objective of arriving at a guideline for translation and national validation of the QOLHEQ, we have developed the design of a reference study on how to adequately assess measurement properties of the QOLHEQ based on interdisciplinary discussions and current standards. We present a step-by-step guideline to assess translation (including cross-cultural adaptation), scale structure, validity, reproducibility, responsiveness, and interpretability. We describe which outcomes should be reported for each measurement property, and give advice on how to calculate these. It is also specified which sample size is needed, how to deal with missing data, and which cutoff values should be applied for the measurement properties assessed during the validation process. In conclusion, this guideline, presenting a reference validation study for the QOLHEQ, creates the possibility to harmonize the national validation of the various language versions of the QOLHEQ. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

The Effects of Salt Water on Mechanical Properties of Glacial Ice

NASA Astrophysics Data System (ADS)

Holt, R. A.; McCarthy, C.

2017-12-01

An improved understanding of the mechanical properties of glacial ice, including factors that may change them, is essential for understanding vulnerability of ice sheets to climate change. It is understood that the temperature of intruding subglacial seawater affects the melting of glacial ice and therefore destabilizes ice shelves, but we hypothesize that seawater bathing the bottom of the glacier may also influence mechanical properties such as friction and elastic modulus. We undertook experiments to determine how the presence of saline solution at grain boundaries of ice might lead to weaker behavior. We created an ice sample by finely grinding and sieving seed ice, pressing it into a rectangular mold, and flooding with a 3.5wt% saline solution. We then quickly brought it to subsolidus (-22°) to completely freeze. The bulk composition of the sample was determined by refractive index to be 0.28wt%. Microstructural characterization of the sample indicates that, above the solidus, the melt phase was located at grain triple junctions and along grain boundaries. To test the frictional behavior of ice with saline sliding against rock, we used a cryo-biaxial apparatus designed to simulate the basal sliding of glacial ice. The experiments were run in the double direct configuration at 100 KPa normal stress and at T=-5°. The results demonstrate that ice containing a liquid saline solution has lower steady state friction than pure ice at the same conditions, and therefore can slip at a faster velocity. In addition to the bi-axial experiment we determined the elastic properties using an ultrasonic velocity testing system. P waves velocities through the saline ice sample were consistent with published values (Spencer et al., 1968, JGR). We also used both measured and estimated values to calculate the Young's modulus. We found that ice containing salt water has a lower Young's modulus than that of pure ice. Salt water significantly changes the mechanical properties of glacial ice and this should be considered in models of glacial stability.

Bacterial L-arabinose isomerases: industrial application for D-tagatose production.

PubMed

Boudebbouze, Samira; Maguin, Emmanuelle; Rhimi, Moez

2011-12-01

D-tagatose is a natural monosaccharide with a low caloric value and has an anti-hyperglycemiant effect. This hexose has potential applications both in pharmaceutical and agro-food industries. However, the use of D-tagatose remains limited by its production cost. Many production procedures including chemical and biological processes were developed and patented. The most profitable production way is based on the use of L-arabinose isomerase which allows the manufacture of D-tagatose with an attractive rate. Future developments are focused on the generation of L-arabinose isomerases having biochemical properties satisfying the industrial applications. This report provides a brief review of the most recent patents that have been published relating to this area.

Heterogeneity Coefficients for Mahalanobis' D as a Multivariate Effect Size.

PubMed

Del Giudice, Marco

2017-01-01

The Mahalanobis distance D is the multivariate generalization of Cohen's d and can be used as a standardized effect size for multivariate differences between groups. An important issue in the interpretation of D is heterogeneity, that is, the extent to which contributions to the overall effect size are concentrated in a small subset of variables rather than evenly distributed across the whole set. Here I present two heterogeneity coefficients for D based on the Gini coefficient, a well-known index of inequality among values of a distribution. I discuss the properties and limitations of the two coefficients and illustrate their use by reanalyzing some published findings from studies of gender differences.

Transport and thermodynamic properties of hydrous melts in the system An-Di.

NASA Astrophysics Data System (ADS)

Giordano, D.; Potuzak, M.; Romano, C.; Russell, J. K.; Nowak, M.; Dingwell, D. B.

2006-12-01

The thermodynamic and transport properties hydrous silicate melts are of fundamental importance for characterization of the dynamics and energetics associated with silicate melts in the Earth. The literature concerning the transport and calorimetric properties of hydrous silicate melts remains scarce. With few exceptions little has been effectively done in order to provide chemical models that bridge the gap between the description of both complex and simple systems. The An-Di system is of general interest to geochemists as well as petrologists because it serves as a simple analogue for basaltic compositions. It was chosen here due to the combination of its simple chemical description and the presence of an extensive database of published experimental data on both its transport and thermodynamic properties. We have measured the viscosity (η)), the glass transition temperatures (Tg) and the heat capacity (Cp) of silicate melts in the An-Di system containing up to 3 wt.% of dissolved H2O. Viscosity data were obtained by using the dilatometric method of micropenetration, whereas a differential scanning calorimeter (DSC) was employed to determine the glass transition temperatures and the heat capacities. In order to characterize the well-known cooling/heating rate dependence of the glass transition temperatures the calorimetric measurements were performed at heating/cooling rate of 5, 10, 15 and 20 K/min. These results together with those of previous experimental studies have been used to provide a compositional model capable of calculating the Newtonian viscosity of melts as well as the Tg and Cp values for the An- Di+H2O system. The non-Arrhenian T-dependence of viscosity is accounted for by the Vogel-Fulcher- Tammann (VFT) and the Adam Gibbs (AG) equations. Our optimizations assume a common, high-T limit (A) for silicate melt viscosity, consistent with values provided by both theoretical and experimental studies. In particular, we also show that glass transition temperatures taken at each single heating/cooling rate are associated to single viscosity values. The equivalence of the activation energy associated to viscous and enthalpic relaxation process at specific temperatures also allow us to calibrate a tool to predict the viscosity of silicate melts by using specific heat curves. The effect of water on the heat capacity of the glass (Cpglass), from dry to nearly 3 wt% H2O, ranges from almost absent up to 20% of the measured Cp,glass values.

Sharing data resources benefits owners as well as miners.

NASA Astrophysics Data System (ADS)

Smith, R. W.

2008-12-01

The most fundamental part of any research activity is the data created. Data are most frequently the result of physical measurements but, increasingly, also result from the operation of a computer code. Given that the methods of creation are properly executed and recorded, data have an intrinsic value regardless of the ensuing study in which they are used. Data are part of the intellectual property associated with the work of a scientist. Like any other form of property, the value to the cognizant community depends upon access and available usage. Data that remain on some hidden storage medium are like a bank account storing funds at with no interest accrual, an apparent waste of opportunity. Not sharing data with the cognizant community needs a justification like security risk or possible danger. The historically contentious issue associated with data as intellectual property is the protection of the owner's rights of first use. This paper contends that data sharing is the proper and most productive strategy for scientists to gain the most value from their work. The first example illustrating the point relates to the Alaska Climate Research Center (www.climate.gi.alaska.edu) operated by the Geophysical Institute (GI) where the data is shared on a website that gets 35,000 hits (2000 visits) per day. The data is a mixture of current weather and historical meteorological observations. The latter could be considered the property of the GI. Although most website hits are for the current weather, web inquiries for meteorological observations across the state, some dating back to 1820, are available for all to use. This kind of sharing brings the most volume and greatest value from the stored data. The second relates to the personal observations of GI faculty members who share their measurements directly on the web as soon as they are available. These data are the same as published in their personal work, and are also available for others to use based on some simple "rules of the road". This strategy broadens the applications of his work and results in more co-authorships along the way. Many federal granting agencies require a similar approach of rapid dissemination of data. The recent introduction of virtual observatories has strengthened this approach and also provides a formalism for the protection of data owners.

Trade Publishing: A Report from the Front.

ERIC Educational Resources Information Center

Fister, Barbara

2001-01-01

Reports on the current condition of trade publishing and its future prospects based on interviews with editors, publishers, agents, and others. Discusses academic libraries and the future of trade publishing, including questions relating to electronic books, intellectual property, and social and economic benefits of sharing information…

Statistically based material properties: A military handbook-17 perspective

NASA Technical Reports Server (NTRS)

Neal, Donald M.; Vangel, Mark G.

1990-01-01

The statistical procedures and their importance in obtaining composite material property values in designing structures for aircraft and military combat systems are described. The property value is such that the strength exceeds this value with a prescribed probability with 95 percent confidence in the assertion. The survival probabilities are the 99th percentile and 90th percentile for the A and B basis values respectively. The basis values for strain to failure measurements are defined in a similar manner. The B value is the primary concern.

Properties of Syntactic Foam for Simulation of Mechanical Insults.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hubbard, Neal Benson; Haulenbeek, Kimberly K.; Spletzer, Matthew A.

Syntactic foam encapsulation protects sensitive components. The energy mitigated by the foam is calculated with numerical simulations. The properties of a syntactic foam consisting of a mixture of an epoxy-rubber adduct and glass microballoons are obtained from published literature and test results. The conditions and outcomes of the tests are discussed. The method for converting published properties and test results to input for finite element models is described. Simulations of the test conditions are performed to validate the inputs.

Topographic variations in biomechanical and biochemical properties in the ankle joint: an in vitro bovine study evaluating native and engineered cartilage.

PubMed

Paschos, Nikolaos K; Makris, Eleftherios A; Hu, Jerry C; Athanasiou, Kyriacos A

2014-10-01

The purposes of this study were to identify differences in the biomechanical and biochemical properties among the articulating surfaces of the ankle joint and to evaluate the functional and biological properties of engineered neocartilage generated using chondrocytes from different locations in the ankle joint. The properties of the different topographies within the ankle joint (tibial plafond, talar dome, and distal fibula) were evaluated in 28 specimens using 7 bovine ankles; the femoral condyle was used as a control. Chondrocytes from the same locations were used to form 28 neocartilage constructs by tissue engineering using an additional 7 bovine ankles. The functional properties of neocartilage were compared with native tissue values. Articular cartilage from the tibial plafond, distal fibula, talar dome, and femoral condyle exhibited Young modulus values of 4.8 ± 0.5 MPa, 3.9 ± 0.1 MPa, 1.7 ± 0.2 MPa, and 4.0 ± 0.5 MPa, respectively. The compressive properties of the corresponding tissues were 370 ± 22 kPa, 242 ± 18 kPa, 255 ± 26 kPa, and 274 ± 18 kPa, respectively. The tibial plafond exhibited 3-fold higher tensile properties and 2-fold higher compressive and shear moduli compared with its articulating talar dome; the same disparity was observed in neocartilage. Similar trends were detected in biochemical data for both native and engineered tissues. The cartilage properties of the various topographic locations within the ankle are significantly different. In particular, the opposing articulating surfaces of the ankle have significantly different biomechanical and biochemical properties. The disparity between tibial plafond and talar dome cartilage and chondrocytes warrants further evaluation in clinical studies to evaluate their exact role in the pathogenesis of ankle lesions. Therapeutic modalities for cartilage lesions need to consider the exact topographic source of the cells or cartilage grafts used. Furthermore, the capacity of generating neocartilage implants from location-specific chondrocytes of the ankle joint may be used in the future as a tool for the treatment of chondral lesions. Copyright © 2014 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

41 CFR 102-75.305 - What type of appraisal value must be obtained for real property disposal transactions?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What type of appraisal value must be obtained for real property disposal transactions? 102-75.305 Section 102-75.305 Public...-75.305 What type of appraisal value must be obtained for real property disposal transactions? For all...

41 CFR 102-75.305 - What type of appraisal value must be obtained for real property disposal transactions?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false What type of appraisal value must be obtained for real property disposal transactions? 102-75.305 Section 102-75.305 Public...-75.305 What type of appraisal value must be obtained for real property disposal transactions? For all...

41 CFR 102-75.305 - What type of appraisal value must be obtained for real property disposal transactions?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false What type of appraisal value must be obtained for real property disposal transactions? 102-75.305 Section 102-75.305 Public...-75.305 What type of appraisal value must be obtained for real property disposal transactions? For all...

41 CFR 102-75.305 - What type of appraisal value must be obtained for real property disposal transactions?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false What type of appraisal value must be obtained for real property disposal transactions? 102-75.305 Section 102-75.305 Public...-75.305 What type of appraisal value must be obtained for real property disposal transactions? For all...

41 CFR 102-75.305 - What type of appraisal value must be obtained for real property disposal transactions?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false What type of appraisal value must be obtained for real property disposal transactions? 102-75.305 Section 102-75.305 Public...-75.305 What type of appraisal value must be obtained for real property disposal transactions? For all...

39 CFR 946.5 - Disposition of property having a value of less than $200.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROCEDURE RELATING TO THE DISPOSITION OF STOLEN MAIL MATTER AND PROPERTY ACQUIRED BY THE POSTAL INSPECTION SERVICE FOR USE AS EVIDENCE § 946.5 Disposition of property having a value of less than $200. Where the... 39 Postal Service 1 2010-07-01 2010-07-01 false Disposition of property having a value of less...

39 CFR 946.5 - Disposition of property having a value of less than $200.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROCEDURE RELATING TO THE DISPOSITION OF STOLEN MAIL MATTER AND PROPERTY ACQUIRED BY THE POSTAL INSPECTION SERVICE FOR USE AS EVIDENCE § 946.5 Disposition of property having a value of less than $200. Where the... 39 Postal Service 1 2011-07-01 2011-07-01 false Disposition of property having a value of less...

Assessing effects of military aircraft noise on residential property values near airbases

NASA Astrophysics Data System (ADS)

Fidell, Sanford; Tabachnick, Barbara; Silvati, Laura; Cook, Brenda

The question, 'Does military aircraft noise exposure affect residential property values in the vicinity of Air Force bases?', can be asked and answered with varying degrees of generality and tolerable errors of inference. Definitive answers are difficult to develop because the question itself may not be meaningful in some circumstances: property values are affected by many factors other than aircraft noise which can fluctuate greatly in different areas and during different time periods; credible attribution of causality for changes in property values uniquely to aircraft noise requires many costly study design measures; and prior findings suggest that if a relationship exists, it is not a large or especially strong one. Thus, evidence of a simple geographic association between aircraft noise exposure and residential property values does not provide a conclusive answer to the question. In an effort to develop more compelling evidence, the US Air Force is planning to compare historical records of sale prices of properties in areas of differential aircraft noise exposure during specific time periods with predictions of sale prices derived from a validated statistical model of residential property values.

31 CFR 543.201 - Prohibited transactions involving blocked property.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Persons List (“SDN List”) (which is accessible via the Office of Foreign Assets Control's Web site... “[COTED].” See § 543.411 concerning entities that may not be listed on the SDN list but whose property and... pursuant to this part also are published on the SDN List, published in the Federal Register and...

The Potential Effect of Sea Level Rise on Coastal Property Values

NASA Astrophysics Data System (ADS)

O'Donnell, J.

2015-12-01

It is well established that one consequence of increasing global sea level is that the frequency of flooding at low-lying coastal sites will increase. We review recent evidence that the effects coastal geometry will create substantial spatial variations in the changes in flooding frequency with scales of order 100km. Using a simple model of the evolution of coastal property values we demonstrate that a consequence of sea level rise is that the appreciation of coastal properties will peak, and then decline relative to higher properties. The time when the value reach a maximum is shown to depend upon the demand for the coastal property, and the local rate of change of flooding frequency due to sea level rise. The simple model is then extended to include, in an elementary manner, the effects on the value of adjacent but higher properties. We show that the effect of increased flooding frequency of the lower properties leads to an accelerated appreciation of the value of upland properties and an accelerated decline in the value of the coastal properties. We then provide some example calculations for selected sites. We conclude with a discussion of comparisons of the prediction of the analyses to recent data, and then comments on the impact of sea level rise on tax base of coastal communities.

36 CFR 18.5 - May property be leased without receiving fair market value rent?

Code of Federal Regulations, 2010 CFR

2010-07-01

.... The determination of fair market value rent shall take into account: (a) Any restrictions on the use of the property or terms of the lease that limit the value and/or the highest and best use of the... without receiving fair market value rent? 18.5 Section 18.5 Parks, Forests, and Public Property NATIONAL...

32 CFR 37.535 - How do I value cost sharing related to real property or equipment?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false How do I value cost sharing related to real... Evaluation Cost Sharing § 37.535 How do I value cost sharing related to real property or equipment? You rarely should accept values for cost sharing contributions of real property or equipment that are in...

36 CFR 1207.31 - Real property.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 1207.31 Parks, Forests, and Public Property NATIONAL ARCHIVES AND RECORDS ADMINISTRATION GENERAL... original purchase to the fair market value of the property. However, in those situations where a grantee or... purchase of the real property to the current fair market value of the property. ...

Snake fangs: 3D morphological and mechanical analysis by microCT, simulation, and physical compression testing.

PubMed

du Plessis, Anton; Broeckhoven, Chris; le Roux, Stephan G

2018-01-01

This Data Note provides data from an experimental campaign to analyse the detailed internal and external morphology and mechanical properties of venomous snake fangs. The aim of the experimental campaign was to investigate the evolutionary development of 3 fang phenotypes and investigate their mechanical behaviour. The study involved the use of load simulations to compare maximum Von Mises stress values when a load is applied to the tip of the fang. The conclusions of this study have been published elsewhere, but in this data note we extend the analysis, providing morphological comparisons including details such as curvature comparisons, thickness, etc. Physical compression results of individual fangs, though reported in the original paper, were also extended here by calculating the effective elastic modulus of the entire snake fang structure including internal cavities for the first time. This elastic modulus of the entire fang is significantly lower than the locally measured values previously reported from indentation experiments, highlighting the possibility that the elastic modulus is higher on the surface than in the rest of the material. The micro-computed tomography (microCT) data are presented both in image stacks and in the form of STL files, which simplifies the handling of the data and allows its re-use for future morphological studies. These fangs might also serve as bio-inspiration for future hypodermic needles. © The Author 2017. Published by Oxford University Press.

Optical properties of ultrarough silver films on silicon

NASA Astrophysics Data System (ADS)

Neff, H.; Henkel, S.; Sass, J. K.; Steinbeiss, E.; Ratz, P.; Müller, J.; Michalke, W.

1996-07-01

The optical properties of inhomogeneously grown rough silver films have been analyzed on the basis of reflectance measurements. Data have been recorded within the wave number range 50 cm-1<λ-1<50 000 cm-1. The results are compared with compact and fairly smooth films, made from the same metal. Rough films reveal very low reflectance and high absorptivity values of nearly 1, at wave numbers ≳200 cm-1. The reflectance of these films is peaking at the bulk plasma resonance hvp of silver at 3.87 eV. Smooth compact films, in contrast, show a pronounced minimum at the same energy. Based on an effective medium approach and available literature data, the dielectric function (DF) and absorption coefficient have been calculated. For rough films, the real part of the DF remains positive within the whole spectral range, but is negative for compact films below hvp, in agreement with published data. The calculated DF of the inhomogeneously grown films fully resembles the experimental observations.

Antimicrobial peptides containing unnatural amino acid exhibit potent bactericidal activity against ESKAPE pathogens.

PubMed

Hicks, R P; Abercrombie, J J; Wong, R K; Leung, K P

2013-01-01

A series of 36 synthetic antimicrobial peptides containing unnatural amino acids were screened to determine their effectiveness to treat Enterococcus faecium, Staphylococcus aureus, Klebsiella pnemoniae, Acinetobacter baumannii, Pseudomonas aeruginosa, and Enterobacter species (ESKAPE) pathogens, which are known to commonly infect chronic wounds. The primary amino acid sequences of these peptides incorporate either three or six dipeptide units consisting of the unnatural amino acids Tetrahydroisoquinolinecarboxylic acid (Tic) and Octahydroindolecarboxylic acid (Oic). The Tic-Oic dipeptide units are separated by SPACER amino acids with specific physicochemical properties that control how these peptides interact with bacterial cell membranes of different chemical compositions. These peptides exhibited minimum inhibitory concentrations (MIC) against these pathogens in the range from >100 to 6.25 μg/mL. The observed diversity of MIC values for these peptides against the various bacterial strains are consistent with our hypothesis that the complementarity of the physicochemical properties of the peptide and the lipid of the bacteria's cell membrane determines the resulting antibacterial activity of the peptide. Published by Elsevier Ltd.

Approaches to the structural modelling of insect wings.

PubMed Central

Wootton, R J; Herbert, R C; Young, P G; Evans, K E

2003-01-01

Insect wings lack internal muscles, and the orderly, necessary deformations which they undergo in flight and folding are in part remotely controlled, in part encoded in their structure. This factor is crucial in understanding their complex, extremely varied morphology. Models have proved particularly useful in clarifying the facilitation and control of wing deformation. Their development has followed a logical sequence from conceptual models through physical and simple analytical to numerical models. All have value provided their limitations are realized and constant comparisons made with the properties and mechanical behaviour of real wings. Numerical modelling by the finite element method is by far the most time-consuming approach, but has real potential in analysing the adaptive significance of structural details and interpreting evolutionary trends. Published examples are used to review the strengths and weaknesses of each category of model, and a summary is given of new work using finite element modelling to investigate the vibration properties and response to impact of hawkmoth wings. PMID:14561349

Properties of polyvinyl alcohol/xylan composite films with citric acid.

PubMed

Wang, Shuaiyang; Ren, Junli; Li, Weiying; Sun, Runcang; Liu, Shijie

2014-03-15

Composite films of xylan and polyvinyl alcohol were produced with citric acid as a new plasticizer or a cross-linking agent. The effects of citric acid content and polyvinyl alcohol/xylan weight ratio on the mechanical properties, thermal stability, solubility, degree of swelling and water vapor permeability of the composite films were investigated. The intermolecular interactions and morphology of composite films were characterized by FTIR spectroscopy and SEM. The results indicated that polyvinyl alcohol/xylan composite films had good compatibility. With an increase in citric acid content from 10% to 50%, the tensile strength reduced from 35.1 to 11.6 MPa. However, the elongation at break increased sharply from 15.1% to 249.5%. The values of water vapor permeability ranged from 2.35 to 2.95 × 10(-7)g/(mm(2)h). Interactions between xylan and polyvinyl alcohol in the presence of citric acid become stronger, which were caused by hydrogen bond and ester bond formation among the components during film forming. Copyright © 2013. Published by Elsevier Ltd.

On the dynamics of a generalized predator-prey system with Z-type control.

PubMed

Lacitignola, Deborah; Diele, Fasma; Marangi, Carmela; Provenzale, Antonello

2016-10-01

We apply the Z-control approach to a generalized predator-prey system and consider the specific case of indirect control of the prey population. We derive the associated Z-controlled model and investigate its properties from the point of view of the dynamical systems theory. The key role of the design parameter λ for the successful application of the method is stressed and related to specific dynamical properties of the Z-controlled model. Critical values of the design parameter are also found, delimiting the λ-range for the effectiveness of the Z-method. Analytical results are then numerically validated by the means of two ecological models: the classical Lotka-Volterra model and a model related to a case study of the wolf-wild boar dynamics in the Alta Murgia National Park. Investigations on these models also highlight how the Z-control method acts in respect to different dynamical regimes of the uncontrolled model. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Thermodynamic tabulations for selected phases in the system CaO-Al2O3-SiO2-H2 at 101.325 kPa (1 atm) between 273.15 and 1800 K

USGS Publications Warehouse

Haas, John L.; Robinson, Glipin R.; Hemingway, Bruch S.

1981-01-01

The standard thermodynamic properties of phases in the lime‐alumina‐silica‐ water system between 273.15 and 1800 K at 101.325 kPa (1 atm) were evalated from published experimental data. Phases included in the compilation are boehmite, diaspore, gibbsite, kaolinite, dickite, halloysite, andalusite, kyanite, sillimanite, Ca‐Al cliniopyroxene, anorthite, gehlenite, grossular, prehnite, zoisite, margarite, wollastonite, cyclowollastonite ( = pseudowollastonite), larnite, Ca olivine, hatrurite, and rankinite. The properties include heat capacity, entropy, relative enthalpy, and the Gibbs energy function of the phases and the enthalpies, Gibbs energies, and equilibrium constants for formation both from the elements and the oxides. Tabulated values are given at 50 K intervals with the 2‐sigma confidence limit at 250 K intervals. Summaries for each phase give the temperature‐ dependent functions for heat capacity, entropy, and relative enthalpy and the experimental data used in the final evaluation.

Effect of sodium chloride on the glass transition of condensed starch systems.

PubMed

Chuang, Lillian; Panyoyai, Naksit; Shanks, Robert; Kasapis, Stefan

2015-10-01

The present investigation deals with the structural properties of condensed potato starch-sodium chloride systems undergoing a thermally induced glass transition. Sample preparation included hot pressing at 120°C for 7 min to produce extensive starch gelatinisation. Materials covered a range of moisture contents from 3.6% to 18.8%, which corresponded to relative humidity values of 11% and 75%. Salt addition was up to 6.0% in formulations. Instrumental work was carried out with dynamic mechanical analysis in tension, modulated differential scanning calorimetry, Fourier transform infrared spectroscopy, scanning electron microscopy and wide angle X-ray diffraction. Experimental conditions ensured the development of amorphous matrices that exhibited thermally reversible glassy consistency. Both moisture content and addition of sodium chloride affected the mechanical strength and glass transition temperature of polymeric systems. Sodium ions interact with chemical moieties of the polysaccharide chain to alter considerably structural properties, as compared to the starch-water matrix. Copyright © 2015. Published by Elsevier Ltd.

[In life determination of the physiological status of decapod crustaceans (Crustacea: Decapoda) by hematological characteristics].

PubMed

Aleksandrova, E N; Kovacheva, N P

2010-01-01

The application of hematological analysis techniques to detecting the physiological status of the economically valued decapods during their culturing, and in monitoring of the condition of their natural populations, is restrained by the incomplete knowledge of these invertebrates circulatory system and its properties. Scarce data on the use of hematological indicators for determining the physiological status of decapods may be found sporadically in published sources; there is shortage of basic standards needed for interpretation of the analytical results. In this regard the paper considers some data on the major properties of hemolymph and its cellular elements; on methods of their examination; and on the results of application of hematological characteristics to assessing the physiological condition of various species of decapods. The hematological indicators suitable for the analysis of live decapods include: time of coagulation and buffer characteristic of hemolymph; concentration of total proteins, copper, calcium, glucose and lactates in it; total number of hemocytes with the consideration of granulocytes share.

Porous starch extracted from Chinese rice wine vinasse: characterization and adsorption properties.

PubMed

Li, Hongyan; Jiao, Aiquan; Wei, Benxi; Wang, Yong; Wu, Chunsen; Jin, Zhengyu; Tian, Yaoqi

2013-10-01

Chinese rice wine vinasse (the fermentation residue after removal of the crude wine or beer) contains 20-30% residual native starch. These starches are partly hydrolyzed by amylase and glucoamylase during rice wine fermentation, indicating that it is a potential source of porous starch, which is a value-added material. In the present study, morphological, short-range order, crystalline, and thermal studies were determined to characterize the structural and chemical properties of vinasse starch. The results showed that vinasse starch granule had a rough and porous shape and was much more ordered than native starch. Vinasse starch also could tolerate a higher temperature than native starch. The water and oil adsorptive capacities of vinasse starch were 1.89 and 4.14 times higher than that of native rice starch. These results suggest that vinasse is an effective and economical source of porous starch for using as adsorbent. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Roughness-dependent tribology effects on discontinuous shear thickening.

PubMed

Hsu, Chiao-Peng; Ramakrishna, Shivaprakash N; Zanini, Michele; Spencer, Nicholas D; Isa, Lucio

2018-05-15

Surface roughness affects many properties of colloids, from depletion and capillary interactions to their dispersibility and use as emulsion stabilizers. It also impacts particle-particle frictional contacts, which have recently emerged as being responsible for the discontinuous shear thickening (DST) of dense suspensions. Tribological properties of these contacts have been rarely experimentally accessed, especially for nonspherical particles. Here, we systematically tackle the effect of nanoscale surface roughness by producing a library of all-silica, raspberry-like colloids and linking their rheology to their tribology. Rougher surfaces lead to a significant anticipation of DST onset, in terms of both shear rate and solid loading. Strikingly, they also eliminate continuous thickening. DST is here due to the interlocking of asperities, which we have identified as "stick-slip" frictional contacts by measuring the sliding of the same particles via lateral force microscopy (LFM). Direct measurements of particle-particle friction therefore highlight the value of an engineering-tribology approach to tuning the thickening of suspensions. Copyright © 2018 the Author(s). Published by PNAS.

Value Arguments in Science Research Articles: Making the Case for the Importance of Research

ERIC Educational Resources Information Center

Carter, Michael

2016-01-01

It is in the interest of scholarly journals to publish important research and of researchers to publish in important journals. One key to making the case for the importance of research in a scholarly article is to incorporate value arguments. Yet there has been no rhetorical analysis of value arguments in the literature. In the context of…

History of the recommended atomic-weight values from 1882 to 1997: A comparision of differences from current values to the estimated uncertainties of earlier values.

USGS Publications Warehouse

Coplen, T.B.; Peiser, H.S.

1998-01-01

International commissions and national committees for atomic weights (mean relative atomic masses) have recommended regularly updated, best values for these atomic weights as applicable to terrestrial sources of the chemical elements. Presented here is a historically complete listing starting with the values in F. W. Clarke's 1882 recalculation, followed by the recommended values in the annual reports of the American Chemical Society's Atomic Weights Commission. From 1903, an International Commission published such reports and its values (scaled to an atomic weight of 16 for oxygen) are here used in preference to those of national committees of Britain, Germany, Spain, Switzerland, and the U.S.A. We have, however, made scaling adjustments from Ar(16O) to Ar(12C) where not negligible. From 1920, this International Commission constituted itself under the International Union of Pure and Applied Chemistry (IUPAC). Since then, IUPAC has published reports (mostly biennially) listing the recommended atomic weights, which are reproduced here. Since 1979, these values have been called the "standard atomic weights" and, since 1969, all values have been published, with their estimated uncertainties. Few of the earlier values were published with uncertainties. Nevertheless, we assessed such uncertainties on the basis of our understanding of the likely contemporary judgement of the values' reliability. While neglecting remaining uncertainties of 1997 values, we derive "differences" and a retrospective index of reliability of atomic-weight values in relation to assessments of uncertainties at the time of their publication. A striking improvement in reliability appears to have been achieved since the commissions have imposed upon themselves the rule of recording estimated uncertainties from all recognized sources of error.

Effect of ball milling on structures and properties of dispersed-type dental amalgam.

PubMed

Chern Lin, Jiin-Huey; Chen, Fred Ying-Yi; Chiang, Hui-Ju; Ju, Chien-Ping

2011-04-01

The purpose of the present study was to investigate the effect of ball milling on the initial mercury vapor release rate and mechanical properties such as compressive strength, diametral tensile strength and creep value, of the dispersed-type dental amalgam, and comparison was made with respect to two commercial amalgam alloys. Ball milling was employed to modify the configuration of the originally spherical-shaped Ag-Cu-Pd dispersant alloy particles. Improvement in mechanical properties while maintaining a low early-stage mercury vapor release rate of the amalgam is attempted. The experimental results show that the amalgam (AmB10) which was made from Ag-Cu-Pd dispersant alloy particles that were ball-milled for 10 min and heat-treated at 300 °C for 2 days exhibited a low initial mercury vapor release rate of 69 pg/mm(2)/s, which was comparable with that of commercial amalgam alloy Tytin (68 pg/mm(2)/s), and was lower than that of Dispersalloy (73 pg/mm(2)/s). As for mechanical properties, amalgam AmB10 exhibited the highest 1h compressive strength (228 MPa), which was higher than that of commercial amalgam alloy Dispersalloy by 72%; while its 24h diametral tensile strength was also the highest (177 MPa), and was higher than that of Dispersalloy by 55%. Furthermore, the creep value of the amalgams made from Ag-Cu-Pd alloy particles with 10 min ball-milling and heat treatment at 300 °C for 2 days was measured to be 0.12%, which was about 20% that of Dispersalloy. It is found that ball milling of the dispersant Ag-Cu-Pd alloy particles for 10 min was able to modify the configuration of the alloy particles into irregular-shapes. Subsequently, heat treatment at 300 °C significantly lowered the initial mercury vapor release rate, increased its 1h compressive strength and 1h diametral tensile strength, and lowered its creep value. Copyright © 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Optical properties of base dentin ceramics for all-ceramic restorations.

PubMed

Shiraishi, Takanobu; Wood, Duncan J; Shinozaki, Nobuya; van Noort, Richard

2011-02-01

The study was conducted to compare the optical parameters of VM7(®) M-shade base dentin ceramics (VITA, Germany) for all ceramic restorations to the chemical composition across the 3D-MASTER(®) shade system. Three disc samples, 13 mm diameter and 1.4 mm thickness, were produced for each M-shade following the manufacturer's instructions. Each disc was ground and polished to a thickness of 1.0 mm. Spectral light transmittance and reflectance data were recorded in the visible spectrum under the standard illuminant D65 and 2° observer at 10 nm intervals by using a computer-controlled spectrophotometer. Opacity, translucency and opalescence parameters were determined for each sample. (1) Spectral transmittance and reflectance in the short-wavelength range systematically decreased with increasing chroma number (M1, M2, M3) when compared within the same value (lightness) group. (2) Spectral transmittance and reflectance decreased systematically across the whole visible spectrum with increasing value group number when compared within the same chroma group. (3) Analysis of relationship between chemical composition and various optical parameters for all the samples showed the significant contribution of ZrO₂ and Y₂O₃ substances to optical properties of the present material. Systematic variations in optical properties of VM7(®) M-shade base dentin ceramics were observed throughout the 3D-MASTER(®) shade system and were suggested to be caused by the fine structure of the sample which can interfere with shorter wavelengths in the visible spectrum. Copyright © 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Physicochemical and mechanical properties of zirconium oxide and niobium oxide modified Portland cement-based experimental endodontic sealers.

PubMed

Viapiana, R; Flumignan, D L; Guerreiro-Tanomaru, J M; Camilleri, J; Tanomaru-Filho, M

2014-05-01

To evaluate the physicochemical and mechanical properties of Portland cement-based experimental sealers (ES) with different radiopacifying agents (zirconium oxide and niobium oxide micro- and nanoparticles) in comparison with the following conventional sealers: AH Plus, MTA Fillapex and Sealapex. The materials were tested for setting time, compressive strength, flow, film thickness, radiopacity, solubility, dimensional stability and formaldehyde release. Data were subjected to anova and Tukey tests (P < 0.05). MTA Fillapex had the shortest setting time and lowest compressive strength values (P < 0.05) compared with the other materials. The ES had flow values similar to the conventional materials, but higher film thickness (P < 0.05) and lower radiopacity (P < 0.05). Similarly to AH Plus, the ES were associated with dimensional expansion (P > 0.05) and lower solubility when compared with MTA Fillapex and Sealapex (P < 0.05). None of the endodontic sealers evaluated released formaldehyde after mixing. With the exception of radiopacity, the Portland cement-based experimental endodontic sealers presented physicochemical properties according to the specifications no 57 ANSI/ADA (ADA Professional Product Review, 2008) and ISO 6876 (Dentistry - Root Canal Sealing Materials, 2012, British Standards Institution, London, UK). The sealers had setting times and flow ability that was adequate for clinical use, satisfactory compressive strength and low solubility. Additional studies should be carried out with the purpose of decreasing the film thickness and to determine the ideal ratio of radiopacifying agents in Portland cement-based root canal sealers. © 2013 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Royalty Fees Part I: The Copyright Clearance Center and Publishers.

ERIC Educational Resources Information Center

Eiblum, Paula; Ardito, Stephanie C.

1998-01-01

Discussion of copyrights, royalty fees, and intellectual property focuses on the Copyright Clearance Center and publishers. Topics include results of a survey of library and information science journal publishers; how users verify royalty fees; how publishers determine fees; royalty fee reporting; and terms and conditions imposed on electronic…

Optimization of extraction efficiency by shear emulsifying assisted enzymatic hydrolysis and functional properties of dietary fiber from deoiled cumin (Cuminum cyminum L.).

PubMed

Ma, Mengmei; Mu, Taihua; Sun, Hongnan; Zhang, Miao; Chen, Jingwang; Yan, Zhibin

2015-07-15

This study evaluated the optimal conditions for extracting dietary fiber (DF) from deoiled cumin by shear emulsifying assisted enzymatic hydrolysis (SEAEH) using the response surface methodology. Fat adsorption capacity (FAC), glucose adsorption capacity (GAC), and bile acid retardation index (BRI) were measured to evaluate the functional properties of the extracted DF. The results revealed that the optimal extraction conditions included an enzyme to substrate ratio of 4.5%, a reaction temperature of 57 °C, a pH value of 7.7, and a reaction time of 155 min. Under these conditions, DF extraction efficiency and total dietary fiber content were 95.12% and 84.18%, respectively. The major components of deoiled cumin DF were hemicellulose (37.25%) and cellulose (33.40%). FAC and GAC increased with decreasing DF particle size (51-100 μm), but decreased with DF particle sizes <26 μm; BRI increased with decreasing DF particle size. The results revealed that SEAEH is an effective method for extracting DF. DF with particle size 26-51 μm had improved functional properties. Copyright © 2015. Published by Elsevier Ltd.

Supercritical impregnation and optical characterization of loaded foldable intraocular lenses using supercritical fluids.

PubMed

Bouledjouidja, Abir; Masmoudi, Yasmine; Li, Yanfeng; He, Wei; Badens, Elisabeth

2017-10-01

To prepare drug-loaded intraocular lenses (IOLs) used to combine cataract surgery with postoperative complication treatment through supercritical impregnation while preserving their optical properties. Aix-Marseille Université, CNRS, Centrale Marseille, Laboratoire de Mécanique, Modélisation & Procédés Propres, Marseille, France, and He University Eye Hospital, Liaoning Province, China. Experimental study. Supercritical impregnations of commercial foldable IOLs used in cataract surgery with ciprofloxacin (an antibiotic) and dexamethasone 21-phosphate disodium salt (an antiinflammatory drug) were performed in a noncontinuous mode. Impregnation amounts were determined through drug-release kinetic studies. The optical characterizations of IOLs were determined by evaluating the dioptric power and the imaging quality by determining the modulating transfer function (MTF) at a specified spatial frequency according to the International Organization for Standardization (ISO 11979-2:2014). Transparent IOLs presenting an effective impregnation were obtained with a prolonged drug delivery during approximately 10 days. Optical characterizations (dioptric powers and MTF values) show preserved optical properties after supercritical treatment/impregnation. Supercritical treatments/impregnations do not damage the optical properties of IOLs and are therefore adequate for the preparation of delivery devices used for cataract surgery. Copyright © 2017. Published by Elsevier Inc.

Some engineering aspects of homoionized mixed clay minerals.

PubMed

Oren, Ali Hakan; Kaya, Abidin

2003-05-01

Many studies have been conducted to investigate the physicochemical behavior of pure clay minerals and predict their engineering performance in the field. In this study, the physicochemical properties of an artificial mixture of different clay minerals namely, 40-50% montmorillonite, 20-30% illite and 10-15% kaolin were investigated. The mixture was homoionized with sodium, Na+; calcium, Ca2+; and aluminum, Al3+. The engineering properties studied were consistency limits, sediment volume, compressibility behavior, and hydraulic conductivity. The results revealed that the liquid, plastic and shrinkage limits of soil increased with increasing cation valence. The hydraulic conductivity of the soil also increased with an increase in the valence of the cation at any given void ratio. Aluminum and sodium treated clays had the highest and the lowest modified compression index values, respectively. Furthermore, trivalent cation saturated clayey soil consolidates three times faster than that of monovalent and two times faster than that of divalent. These properties of the soils determined were, in general, similar to those of kaolinite rather than those of montmorillonite. The comparison of the results obtained with the published data in the literature revealed that the physicochemical behavior of the tested clay soil was, in general, similar to that of kaolinite.

Molecular characterization of biochars and their influence on microbiological properties of soil.

PubMed

Chintala, Rajesh; Schumacher, Thomas E; Kumar, Sandeep; Malo, Douglas D; Rice, James A; Bleakley, Bruce; Chilom, Gabriela; Clay, David E; Julson, James L; Papiernik, Sharon K; Gu, Zheng Rong

2014-08-30

The tentative connection between the biochar surface chemical properties and their influence on microbially mediated mineralization of C, N, and S with the help of enzymes is not well established. This study was designed to investigate the effect of different biomass conversion processes (microwave pyrolysis, carbon optimized gasification, and fast pyrolysis using electricity) on the composition and surface chemistry of biochar materials produced from corn stover (Zea mays L.), switchgrass (Panicum virgatum L.), and Ponderosa pine wood residue (Pinus ponderosa Lawson and C. Lawson) and determine the effect of biochars on mineralization of C, N, and S and associated soil enzymatic activities including esterase (fluorescein diacetate hydrolase, FDA), dehydrogenase (DHA), β-glucosidase (GLU), protease (PROT), and aryl sulfatase (ARSUL) in two different soils collected from footslope (Brookings) and crest (Maddock) positions of a landscape. Chemical properties of biochar materials produced from different batches of gasification process were fairly consistent. Biochar materials were found to be highly hydrophobic (low H/C values) with high aromaticity, irrespective of biomass feedstock and pyrolytic process. The short term incubation study showed that biochar had negative effects on microbial activity (FDA and DHA) and some enzymes including β-glucosidase and protease. Published by Elsevier B.V.

A novel conversion of the groundwater treatment sludge to magnetic particles for the adsorption of methylene blue.

PubMed

Zhu, Suiyi; Fang, Shuai; Huo, Mingxin; Yu, Yang; Chen, Yu; Yang, Xia; Geng, Zhi; Wang, Yi; Bian, Dejun; Huo, Hongliang

2015-07-15

Iron sludge, produced from filtration and backwash of groundwater treatment plant, has long been considered as a waste for landfill. In this study, iron sludge was reused to synthesize Fe3O4 magnetic particles (MPs) by using a novel solvothermal process. Iron sludge contained abundant amounts of silicon, iron, and aluminum and did not exhibit magnetic properties. After treatment for 4h, the amorphous Fe in iron sludge was transformed into magnetite Fe3O4, which could be easily separated from aqueous solution with a magnet. The prepared particles demonstrated the intrinsic properties of soft magnetic materials and could aggregate into a size of 1 μm. MPs treated for 10h exhibited excellent magnetic properties and a saturation magnetization value of 9 emu/g. The obtained particles presented the optimal adsorption of methylene blue under mild conditions, and the maximum adsorption capacity was 99.4 mg/g, which was higher than that of granular active carbon. The simple solvothermal method can be used to prepare Fe3O4 MPs from iron sludge, and the products could be applied to treatment of dyeing wastewater. Copyright © 2015. Published by Elsevier B.V.

Does Federally Subsidized Rental Housing Depress Neighborhood Property Values?

ERIC Educational Resources Information Center

Ellen, Ingrid Gould; Schwartz, Amy Ellen; Voicu, Ioan; Schill, Michael H.

2007-01-01

Few communities welcome federally subsidized rental housing, with one of the most commonly voiced fears being reductions in property values. Yet there is little empirical evidence that subsidized housing depresses neighborhood property values. This paper estimates and compares the neighborhood impacts of a broad range of federally subsidized…

26 CFR 20.2032A-4 - Method of valuing farm real property.

Code of Federal Regulations, 2011 CFR

2011-04-01

... for property on which buildings or other improvements are located and farms including multiple... property on which comparable buildings or improvements are located must be identified for specially valued property on which buildings or other real property improvements are located. In cases involving multiple...

26 CFR 20.2032A-4 - Method of valuing farm real property.

Code of Federal Regulations, 2010 CFR

2010-04-01

... for property on which buildings or other improvements are located and farms including multiple... property on which comparable buildings or improvements are located must be identified for specially valued property on which buildings or other real property improvements are located. In cases involving multiple...

Inferring heat recirculation and albedo for exoplanetary atmospheres: Comparing optical phase curves and secondary eclipse data

NASA Astrophysics Data System (ADS)

von Paris, P.; Gratier, P.; Bordé, P.; Selsis, F.

2016-03-01

Context. Basic atmospheric properties, such as albedo and heat redistribution between day- and nightsides, have been inferred for a number of planets using observations of secondary eclipses and thermal phase curves. Optical phase curves have not yet been used to constrain these atmospheric properties consistently. Aims: We model previously published phase curves of CoRoT-1b, TrES-2b, and HAT-P-7b, and infer albedos and recirculation efficiencies. These are then compared to previous estimates based on secondary eclipse data. Methods: We use a physically consistent model to construct optical phase curves. This model takes Lambertian reflection, thermal emission, ellipsoidal variations, and Doppler boosting, into account. Results: CoRoT-1b shows a non-negligible scattering albedo (0.11 < AS < 0.3 at 95% confidence) as well as small day-night temperature contrasts, which are indicative of moderate to high re-distribution of energy between dayside and nightside. These values are contrary to previous secondary eclipse and phase curve analyses. In the case of HAT-P-7b, model results suggest a relatively high scattering albedo (AS ≈ 0.3). This confirms previous phase curve analysis; however, it is in slight contradiction to values inferred from secondary eclipse data. For TrES-2b, both approaches yield very similar estimates of albedo and heat recirculation. Discrepancies between recirculation and albedo values as inferred from secondary eclipse and optical phase curve analyses might be interpreted as a hint that optical and IR observations probe different atmospheric layers, hence temperatures.

International consensus principles for ethical wildlife control.

PubMed

Dubois, Sara; Fenwick, Nicole; Ryan, Erin A; Baker, Liv; Baker, Sandra E; Beausoleil, Ngaio J; Carter, Scott; Cartwright, Barbara; Costa, Federico; Draper, Chris; Griffin, John; Grogan, Adam; Howald, Gregg; Jones, Bidda; Littin, Kate E; Lombard, Amanda T; Mellor, David J; Ramp, Daniel; Schuppli, Catherine A; Fraser, David

2017-08-01

Human-wildlife conflicts are commonly addressed by excluding, relocating, or lethally controlling animals with the goal of preserving public health and safety, protecting property, or conserving other valued wildlife. However, declining wildlife populations, a lack of efficacy of control methods in achieving desired outcomes, and changes in how people value animals have triggered widespread acknowledgment of the need for ethical and evidence-based approaches to managing such conflicts. We explored international perspectives on and experiences with human-wildlife conflicts to develop principles for ethical wildlife control. A diverse panel of 20 experts convened at a 2-day workshop and developed the principles through a facilitated engagement process and discussion. They determined that efforts to control wildlife should begin wherever possible by altering the human practices that cause human-wildlife conflict and by developing a culture of coexistence; be justified by evidence that significant harms are being caused to people, property, livelihoods, ecosystems, and/or other animals; have measurable outcome-based objectives that are clear, achievable, monitored, and adaptive; predictably minimize animal welfare harms to the fewest number of animals; be informed by community values as well as scientific, technical, and practical information; be integrated into plans for systematic long-term management; and be based on the specifics of the situation rather than negative labels (pest, overabundant) applied to the target species. We recommend that these principles guide development of international, national, and local standards and control decisions and implementation. © 2017 The Authors. Conservation Biology published by Wiley Periodicals, Inc. on behalf of Society for Conservation Biology.

Branch age and light conditions determine leaf-area-specific conductivity in current shoots of Scots pine.

PubMed

Grönlund, Leila; Hölttä, Teemu; Mäkelä, Annikki

2016-08-01

Shoot size and other shoot properties more or less follow the availability of light, but there is also evidence that the topological position in a tree crown has an influence on shoot development. Whether the hydraulic properties of new shoots are more regulated by the light or the position affects the shoot acclimation to changing light conditions and thereby to changing evaporative demand. We investigated the leaf-area-specific conductivity (and its components sapwood-specific conductivity and Huber value) of the current-year shoots of Scots pine (Pinus sylvestris L.) in relation to light environment and topological position in three different tree classes. The light environment was quantified in terms of simulated transpiration and the topological position was quantified by parent branch age. Sample shoot measurements included length, basal and tip diameter, hydraulic conductivity of the shoot, tracheid area and density, and specific leaf area. In our results, the leaf-area-specific conductivity of new shoots declined with parent branch age and increased with simulated transpiration rate of the shoot. The relation to transpiration demand seemed more decisive, since it gave higher R(2) values than branch age and explained the differences between the tree classes. The trend of leaf-area-specific conductivity with simulated transpiration was closely related to Huber value, whereas the trend of leaf-area-specific conductivity with parent branch age was related to a similar trend in sapwood-specific conductivity. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Heat capacity and thermodynamic properties for coesite and jadeite, reexamination of the quartz-coesite equilibrium boundary

USGS Publications Warehouse

Hemingway, B.S.; Bohlen, S.R.; Hankins, W.B.; Westrum, E.F.; Kuskov, O.L.

1998-01-01

The heat capacities of synthetic coesite and jadeite were measured between about 15 and 850 K by adiabatic and differential scanning calorimetry. The experimental data were smoothed and estimates were made of heat capacities to 1800 K. The following equations represent our estimate of the heat capacities of coesite and jadeite between 298.15 and 1800 K: [see original article for formula]. Tables of thermodynamic values for coesite and jadeite to 1800 K are presented. The entropies of coesite and jadeite are 40.38 ?? 0.12 and 136.5 ?? 0.32 J/(mol.K), respectively, at 298.15 K. The entropy for coesite derived here confirms the value published earlier by Holm et al. (1967). We have derived an equation to describe the quartz-coesite boundary over the temperature range of 600 to 1500 K, P(GPa) = 1.76 + 0.001T(K). Our results are in agreement with the enthalpy of transition reported by Akaogi and Navrotsky (1984) and yield -907.6 ?? 1.4 kJ/mol for the enthalpy of formation of coesite from the elements at 298.15 K and 1 bar, in agreement with the value recommended by CODATA (Khodakovsky et al. 1995). Several sources of uncertainty remain unacceptably high, including: the heat capacities of coesite at temperatures above about 1000 K; the heat capacities and volumetric properties of ?? quartz at higher pressures and at temperatures above 844 K; the pressure corrections for the piston cylinder apparatus used to determine the quartz-coesite equilibrium boundary.

A heterogeneous human tissue mimicking phantom for RF heating and MRI thermal monitoring verification

NASA Astrophysics Data System (ADS)

Yuan, Yu; Wyatt, Cory; Maccarini, Paolo; Stauffer, Paul; Craciunescu, Oana; MacFall, James; Dewhirst, Mark; Das, Shiva K.

2012-04-01

This paper describes a heterogeneous phantom that mimics a human thigh with a deep-seated tumor, for the purpose of studying the performance of radiofrequency (RF) heating equipment and non-invasive temperature monitoring with magnetic resonance imaging (MRI). The heterogeneous cylindrical phantom was constructed with an outer fat layer surrounding an inner core of phantom material mimicking muscle, tumor and marrow-filled bone. The component materials were formulated to have dielectric and thermal properties similar to human tissues. The dielectric properties of the tissue mimicking phantom materials were measured with a microwave vector network analyzer and impedance probe over the frequency range of 80-500 MHz and at temperatures of 24, 37 and 45 °C. The specific heat values of the component materials were measured using a differential scanning calorimeter over the temperature range of 15-55 °C. The thermal conductivity value was obtained from fitting the curves obtained from one-dimensional heat transfer measurement. The phantom was used to verify the operation of a cylindrical four-antenna annular phased array extremity applicator (140 MHz) by examining the proton resonance frequency shift (PRFS) thermal imaging patterns for various magnitude/phase settings (including settings to focus heating in tumors). For muscle and tumor materials, MRI was also used to measure T1/T2* values (1.5 T) and to obtain the slope of the PRFS phase change versus temperature change curve. The dielectric and thermal properties of the phantom materials were in close agreement to well-accepted published results for human tissues. The phantom was able to successfully demonstrate satisfactory operation of the tested heating equipment. The MRI-measured thermal distributions matched the expected patterns for various magnitude/phase settings of the applicator, allowing the phantom to be used as a quality assurance tool. Importantly, the material formulations for the various tissue types may be used to construct customized phantoms that are tailored for different anatomical sites.

Economic analysis of the gypsy moth problem in the northeast: II. applied to residential property

Treesearch

Brian R. Payne; William B. White; Roger E. McCay; Robert R. McNichols

1973-01-01

Guidelines are presented for determining dollar losses in residential property values from tree mortality caused by the gypsy moth. The method is based on an earlier study in Amherst, Massachusetts, of the contribution of trees to property values. For each target area, the method requires data on property value, lot size, and number of trees 6 inches dbh and larger for...

26 CFR 1.1015-1 - Basis of property acquired by gift after December 31, 1920.

Code of Federal Regulations, 2012 CFR

2012-04-01

... sections 1016 and 1017) is greater than the fair market value of the property at the time of the gift. In such case, the basis for determining loss is the fair market value at the time of the gift. (2) The... fair market value of the property at the date of gift is $90,000. A later sells the property for $95...

Effect of presence of sulphurdioxide on acetylation and sorption isotherm of acetylated starches from cultivars of cassava.

PubMed

Osundahunsi, Oluwatooyin Faramade; Seidu, Kudirat Titilope; Mueller, Rudolf

2014-05-15

Starches from cultivars of cassava were modified with acetic anhydride. Treatment with sulphurdioxide was compared with native. The starches were evaluated for functional properties and moisture isotherms were calculated. Addition of 3.5% acetic anhydride resulted in starches with DS of 1.66% and 3.25% in sweet and bitter cultivars. Sweet starch alone will be applicable for food. Least gelation concentrations for the native were 14% and 10% against 6% and 8% acetylated samples, respectively. Degree of substitution (DS) was reduced with SO2 by 45% and 39% in sweet and bitter cultivar with 150 mg/kg starch, respectively. Swelling power and solubility increased with DS. Exudates from samples varied. Monolayer values of the starches were between 1.05% and 9.16% under 18 °C and 30 °C that simulated distribution and storage. R(2) value of water adsorbed and water activity ranged from 50% to 97%. X-ray patterns were not disrupted. Copyright © 2014. Published by Elsevier Ltd.

Using straw hydrolysate to cultivate Chlorella pyrenoidosa for high-value biomass production and the nitrogen regulation for biomass composition.

PubMed

Zhang, Tian-Yuan; Wang, Xiao-Xiong; Wu, Yin-Hu; Wang, Jing-Han; Deantes-Espinosa, Victor M; Zhuang, Lin-Lan; Hu, Hong-Ying; Wu, Guang-Xue

2017-11-01

Heterotrophic cultivation of Chlorella pyrenoidosa based on straw substrate was proposed as a promising approach in this research. The straw pre-treated by ammonium sulfite method was enzymatically hydrolyzed for medium preparation. The highest intrinsic growth rate of C. pyrenoidosa reached to 0.097h -1 in hydrolysate medium, which was quicker than that in glucose medium. Rising nitrogen concentration could significantly increase protein content and decrease lipid content in biomass, meanwhile fatty acids composition kept stable. The highest protein and lipid content in microalgal biomass reached to 62% and 32% under nitrogen excessive and deficient conditions, respectively. Over 40% of amino acids and fatty acids in biomass belonged to essential amino acids (EAA) and essential fatty acids (EFA), which were qualified for high-value uses. This research revealed the rapid biomass accumulation property of C. pyrenoidosa in straw hydrolysate medium and the effectiveness of nitrogen regulation to biomass composition at heterotrophic condition. Copyright © 2017. Published by Elsevier Ltd.

Production of hydrocarbon fuels from pyrolysis of soybean oils using a basic catalyst.

PubMed

Xu, Junming; Jiang, Jianchun; Sun, Yunjuan; Chen, Jie

2010-12-01

Triglycerides obtained from animals and plants have attracted great attention from researchers for developing an environmental friendly and high-quality fuel, free of nitrogen and sulfur. In the present work, the production of biofuel by catalytic cracking of soybean oil over a basic catalyst in a continuous pyrolysis reactor at atmospheric pressure has been studied. Experiments were designed to study the effect of different types of catalysts on the yield and acid value of the diesel and gasoline fractions from the pyrolytic oil. It was found that basic catalyst gave a product with relatively low acid number. These pyrolytic oils were also further reacted with alcohol in order to decrease their acid value. After esterification, the physico-chemical properties of these biofuels were characterized, and compared with Chinese specifications for conventional diesel fuels. The results showed that esterification of pyrolytic oil from triglycerides represents an alternative technique for producing biofuels from soybean oils with characteristics similar to those of petroleum fuels. Published by Elsevier Ltd.

Permeability study of cancellous bone and its idealised structures.

PubMed

Syahrom, Ardiyansyah; Abdul Kadir, Mohammed Rafiq; Harun, Muhamad Nor; Öchsner, Andreas

2015-01-01

Artificial bone is a suitable alternative to autografts and allografts, however their use is still limited. Though there were numerous reports on their structural properties, permeability studies of artificial bones were comparably scarce. This study focused on the development of idealised, structured models of artificial cancellous bone and compared their permeability values with bone surface area and porosity. Cancellous bones from fresh bovine femur were extracted and cleaned following an established protocol. The samples were scanned using micro-computed tomography (μCT) and three-dimensional models of the cancellous bones were reconstructed for morphology study. Seven idealised and structured cancellous bone models were then developed and fabricated via rapid prototyping technique. A test-rig was developed and permeability tests were performed on the artificial and real cancellous bones. The results showed a linear correlation between the permeability and the porosity as well as the bone surface area. The plate-like idealised structure showed a similar value of permeability to the real cancellous bones. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Influence of the nitrogen content on the optical properties of CNx films.

PubMed

Abd El-Kader, F H; Moharram, M A; Khafagia, M G; Mamdouh, Fathia

2012-11-01

Polycrystalline carbon nitride thin films were prepared by electrolysis of methanol-urea solution at different concentrations of urea to methanol and applied voltage 800 volts for 10h. Grazing incidence X-ray diffraction (GIXRD) revealed that the crystalline structure of carbon nitride films at moderate nitrogen content changed from amorphous phase to polycrystalline α-C(3)N(4), and β-C(3)N(4) phases. The optical transmission analysis of the films revealed that the band gap value for indirect allowed transitions increased with increasing nitrogen content, while the associated phonon energy value showed the opposite behavior. The refractive index and the extinction coefficient of the samples deposited with different concentrations were determined as a function of wavelength. The refractive index decreases with increasing both nitrogen content and crystallinity. The refractive index dispersion for the investigated samples is discussed in terms of the single oscillator model and oscillator parameters. Copyright © 2012. Published by Elsevier B.V.

The α-amylase and α-glucosidase inhibitory effects of Irish seaweed extracts.

PubMed

Lordan, Sinéad; Smyth, Thomas J; Soler-Vila, Anna; Stanton, Catherine; Ross, R Paul

2013-12-01

To date, numerous studies have reported on the antidiabetic properties of various plant extracts through inhibition of carbohydrate-hydrolysing enzymes. The objective of this research was to evaluate extracts of seaweeds for α-amylase and α-glucosidase inhibitory effects. Cold water and ethanol extracts of 15 seaweeds were initially screened and from this, five brown seaweed species were chosen. The cold water and ethanol extracts of Ascophyllum nodosum had the strongest α-amylase inhibitory effect with IC50 values of 53.6 and 44.7 μg/ml, respectively. Moreover, the extracts of Fucus vesiculosus Linnaeus were found to be potent inhibitors of α-glucosidase with IC50 values of 0.32 and 0.49 μg/ml. The observed effects were associated with the phenolic content and antioxidant activity of the extracts, and the concentrations used were below cytotoxic levels. Overall, our findings suggest that brown seaweed extracts may limit the release of simple sugars from the gut and thereby alleviate postprandial hyperglycaemia. Copyright © 2013. Published by Elsevier Ltd.

Theoretical Study of Energy Levels and Transition Probabilities of Boron Atom

NASA Astrophysics Data System (ADS)

Tian Yi, Zhang; Neng Wu, Zheng

2009-08-01

Full Text PDF Though the electrons configuration for boron atom is simple and boron atom has long been of interest for many researchers, the theoretical studies for properties of BI are not systematic, there are only few results reported on energy levels of high excited states of boron, and transition measurements are generally restricted to transitions involving ground states and low excited states without considering fine structure effects, provided only multiplet results, values for transitions between high excited states are seldom performed. In this article, by using the scheme of the weakest bound electron potential model theory calculations for energy levels of five series are performed and with the same method we give the transition probabilities between excited states with considering fine structure effects. The comprehensive set of calculations attempted in this paper could be of some value to workers in the field because of the lack of published calculations for the BI systems. The perturbations coming from foreign perturbers are taken into account in studying the energy levels. Good agreement between our results and the accepted values taken from NIST has been obtained. We also reported some values of energy levels and transition probabilities not existing on the NIST data bases.

The implicit value of tree cover in the U.S.: A meta-analysis of hedonic property value studies

Treesearch

Shyamani Siriwardena; Kevin Boyle; Tom Holmes; P. Eric Wiseman

2016-01-01

Trees in residential neighborhoods and communities provide benefits for homeowners that are capitalized into residential property values. In this paper, we collected data from hedonic property value studies and merged these data with ancillary spatial data describing forest and socio-economic characteristics surrounding each study area to conduct a meta-analysis of the...

Short communications published online in the British Journal of Oral and Maxillofacial Surgery during 2010-2011.

PubMed

Colbert, S; Southorn, B; Rosenbaum, G; Aldridge, T; Brennan, P A

2012-09-01

The British Journal of Oral and Maxillofacial Surgery (BJOMS) publishes many types of papers including original articles, review articles, and short communications. Many of the latter are isolated case reports of rare or interesting diseases or of difficult or unexpected complications. While case reports are sometimes considered to be of little educational or clinical value, and as such do little to advance medical knowledge, they do have an important role, and many trainees begin their publishing careers writing such papers. There is increasing pressure for space in paper medical journals and, for this reason, some journals either limit or do not publish short publications in print copy but instead put them online. Using established criteria, we previously evaluated all 142 short communications published in the BJOMS during 2008-2009 and found that 48% of them had little or no educational value. As a result, the editorial board of BJOMS took the decision to publish most short communications online only. We have now analysed 48 short communications that were published online only during 2010-2011. Most (80%) were single case reports that covered virtually the whole remit of the specialty, and over half (56%) were published by authors based in the UK. While many of these papers did not add important new information to existing knowledge, these types of article are clearly of value both for trainees and for experienced surgeons. We think that these should continue to be supported as, in addition to their educational value, they are an excellent way for trainees to start to write. Copyright © 2012 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Sorption behavior of 17 phthalic acid esters on three soils: effects of pH and dissolved organic matter, sorption coefficient measurement and QSPR study.

PubMed

Yang, Fen; Wang, Meng; Wang, Zunyao

2013-09-01

This work studies the sorption behaviors of phthalic acid esters (PAEs) on three soils by batch equilibration experiments and quantitative structure property relationship (QSPR) methodology. Firstly, the effects of soil type, dissolved organic matter and pH on the sorption of four PAEs (DMP, DEP, DAP, DBP) are investigated. The results indicate that the soil organic carbon content has a crucial influence on sorption progress. In addition, a negative correlation between pH values and the sorption capacities was found for these four PAEs. However, the effect of DOM on PAEs sorption may be more complicated. The sorption of four PAEs was promoted by low concentrations of DOM, while, in the case of high concentrations, the influence of DOM on the sorption was complicated. Then the organic carbon content normalized sorption coefficient (logKoc) values of 17 PAEs on three soils were measured, and the mean values ranged from 1.50 to 7.57. The logKoc values showed good correlation with the corresponding logKow values. Finally, two QSPR models were developed with 13 theoretical parameters to get reliable logKoc predictions. The leave-one-out cross validation (CV-LOO) indicated that the internal predictive power of the two models was satisfactory. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

36 CFR 1120.5 - Information published in the Federal Register.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Information published in the... TRANSPORTATION BARRIERS COMPLIANCE BOARD PUBLIC AVAILABILITY OF INFORMATION Published Information § 1120.5 Information published in the Federal Register. (a) General. In accordance with the provisions of 5 U.S.C. 552...

41 CFR 105-60.201 - Published information and rules.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Published information... Agency Information and Rules in the Federal Register § 105-60.201 Published information and rules. In accordance with 5 U.S.C. 552(a)(1), GSA publishes in the Federal Register, for the guidance of the public...

41 CFR 105-60.202 - Published materials available for sale to the public.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Published materials... Published materials available for sale to the public. (a) Substantive rules of general applicability adopted by GSA as authorized by law that this agency publishes in the Federal Register and which are...

Assessing the effect of publicly assisted brownfield redevelopment on surrounding property values

Treesearch

Christopher A. De Sousa; Changson Wu; Lynne M. Westphal

2009-01-01

This study measures and compares the impact of publicly assisted brownfield redevelopment on nearby residential property values in Milwaukee and Minneapolis. It also examines the influence of land use, neighborhood characteristics, and other redevelopment factors on this impact. The research approach incorporates a hedonic method to quantify nearby property value...

14 CFR 1261.109 - Computation of allowance.

Code of Federal Regulations, 2011 CFR

2011-01-01

... to the loss or damage of property lost or damaged beyond economical repair, less any salvage value... price paid in cash or property, or the value at the time of acquisition if not acquired by purchase or exchange). There will be no allowance for replacement cost or for appreciation in the value of the property...

24 CFR 17.48 - Computation of amount of award.

Code of Federal Regulations, 2011 CFR

2011-04-01

... loss or damage, of property lost or damaged beyond economical repair, less any salvage value; or (2... property, or the value at the time of acquisition if not acquired by purchase or exchange); and there will be no allowance for replacement cost or for appreciation in the value of the property. Subject to...

44 CFR 11.78 - Computation of amount of award.

Code of Federal Regulations, 2011 CFR

2011-10-01

... in the value of the property. Subject to these limitations, the amount allowable is either: (1) The depreciated value, immediately prior to the loss or damage, of property lost or damaged beyond economical... the item (either the price paid in cash or property, or the value at the time of acquisition if not...

Comparing published scientific journal articles to their pre-print versions

DOE PAGES

Klein, Martin; Broadwell, Peter; Farb, Sharon E.; ...

2018-02-05

Academic publishers claim that they add value to scholarly communications by coordinating reviews and contributing and enhancing text during publication. These contributions come at a considerable cost: US academic libraries paid $1.7 billion for serial subscriptions in 2008 alone. Library budgets, in contrast, are flat and not able to keep pace with serial price inflation. Here, we have investigated the publishers’ value proposition by conducting a comparative study of pre-print papers from two distinct science, technology, and medicine corpora and their final published counterparts. This comparison had two working assumptions: (1) If the publishers’ argument is valid, the text ofmore » a pre-print paper should vary measurably from its corresponding final published version, and (2) by applying standard similarity measures, we should be able to detect and quantify such differences. Our analysis revealed that the text contents of the scientific papers generally changed very little from their pre-print to final published versions. These findings contribute empirical indicators to discussions of the added value of commercial publishers and therefore should influence libraries’ economic decisions regarding access to scholarly publications.« less

Comparing published scientific journal articles to their pre-print versions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, Martin; Broadwell, Peter; Farb, Sharon E.

Academic publishers claim that they add value to scholarly communications by coordinating reviews and contributing and enhancing text during publication. These contributions come at a considerable cost: US academic libraries paid $1.7 billion for serial subscriptions in 2008 alone. Library budgets, in contrast, are flat and not able to keep pace with serial price inflation. Here, we have investigated the publishers’ value proposition by conducting a comparative study of pre-print papers from two distinct science, technology, and medicine corpora and their final published counterparts. This comparison had two working assumptions: (1) If the publishers’ argument is valid, the text ofmore » a pre-print paper should vary measurably from its corresponding final published version, and (2) by applying standard similarity measures, we should be able to detect and quantify such differences. Our analysis revealed that the text contents of the scientific papers generally changed very little from their pre-print to final published versions. These findings contribute empirical indicators to discussions of the added value of commercial publishers and therefore should influence libraries’ economic decisions regarding access to scholarly publications.« less

Analysis of determinations of the distance between the sun and the galactic center

NASA Astrophysics Data System (ADS)

Malkin, Z. M.

2013-02-01

The paper investigates the question of whether or not determinations of the distance between the Sun and the Galactic center R 0 are affected by the so-called "bandwagon effect", leading to selection effects in published data that tend to be close to expected values, as was suggested by some authors. It is difficult to estimate numerically a systematic uncertainty in R 0 due to the bandwagon effect; however, it is highly probable that, even if widely accepted values differ appreciably from the true value, the published results should eventually approach the true value despite the bandwagon effect. This should be manifest as a trend in the published R 0 data: if this trend is statistically significant, the presence of the bandwagon effect can be suspected in the data. Fifty two determinations of R 0 published over the last 20 years were analyzed. These data reveal no statistically significant trend, suggesting they are unlikely to involve any systematic uncertainty due to the bandwagon effect. At the same time, the published data show a gradual and statistically significant decrease in the uncertainties in the R 0 determinations with time.

On Some Nonclassical Algebraic Properties of Interval-Valued Fuzzy Soft Sets

PubMed Central

2014-01-01

Interval-valued fuzzy soft sets realize a hybrid soft computing model in a general framework. Both Molodtsov's soft sets and interval-valued fuzzy sets can be seen as special cases of interval-valued fuzzy soft sets. In this study, we first compare four different types of interval-valued fuzzy soft subsets and reveal the relations among them. Then we concentrate on investigating some nonclassical algebraic properties of interval-valued fuzzy soft sets under the soft product operations. We show that some fundamental algebraic properties including the commutative and associative laws do not hold in the conventional sense, but hold in weaker forms characterized in terms of the relation =L. We obtain a number of algebraic inequalities of interval-valued fuzzy soft sets characterized by interval-valued fuzzy soft inclusions. We also establish the weak idempotent law and the weak absorptive law of interval-valued fuzzy soft sets using interval-valued fuzzy soft J-equal relations. It is revealed that the soft product operations ∧ and ∨ of interval-valued fuzzy soft sets do not always have similar algebraic properties. Moreover, we find that only distributive inequalities described by the interval-valued fuzzy soft L-inclusions hold for interval-valued fuzzy soft sets. PMID:25143964

On some nonclassical algebraic properties of interval-valued fuzzy soft sets.

PubMed

Liu, Xiaoyan; Feng, Feng; Zhang, Hui

2014-01-01

Interval-valued fuzzy soft sets realize a hybrid soft computing model in a general framework. Both Molodtsov's soft sets and interval-valued fuzzy sets can be seen as special cases of interval-valued fuzzy soft sets. In this study, we first compare four different types of interval-valued fuzzy soft subsets and reveal the relations among them. Then we concentrate on investigating some nonclassical algebraic properties of interval-valued fuzzy soft sets under the soft product operations. We show that some fundamental algebraic properties including the commutative and associative laws do not hold in the conventional sense, but hold in weaker forms characterized in terms of the relation = L . We obtain a number of algebraic inequalities of interval-valued fuzzy soft sets characterized by interval-valued fuzzy soft inclusions. We also establish the weak idempotent law and the weak absorptive law of interval-valued fuzzy soft sets using interval-valued fuzzy soft J-equal relations. It is revealed that the soft product operations ∧ and ∨ of interval-valued fuzzy soft sets do not always have similar algebraic properties. Moreover, we find that only distributive inequalities described by the interval-valued fuzzy soft L-inclusions hold for interval-valued fuzzy soft sets.

First Nuclear DNA Amounts in more than 300 Angiosperms

PubMed Central

ZONNEVELD, B. J. M.; LEITCH, I. J.; BENNETT, M. D.

2005-01-01

• Background and Aims Genome size (DNA C-value) data are key biodiversity characters of fundamental significance used in a wide variety of biological fields. Since 1976, Bennett and colleagues have made scattered published and unpublished genome size data more widely accessible by assembling them into user-friendly compilations. Initially these were published as hard copy lists, but since 1997 they have also been made available electronically (see the Plant DNA C-values database www.kew.org/cval/homepage.html). Nevertheless, at the Second Plant Genome Size Meeting in 2003, Bennett noted that as many as 1000 DNA C-value estimates were still unpublished and hence unavailable. Scientists were strongly encouraged to communicate such unpublished data. The present work combines the databasing experience of the Kew-based authors with the unpublished C-values produced by Zonneveld to make a large body of valuable genome size data available to the scientific community. • Methods C-values for angiosperm species, selected primarily for their horticultural interest, were estimated by flow cytometry using the fluorochrome propidium iodide. The data were compiled into a table whose form is similar to previously published lists of DNA amounts by Bennett and colleagues. • Key Results and Conclusions The present work contains C-values for 411 taxa including first values for 308 species not listed previously by Bennett and colleagues. Based on a recent estimate of the global published output of angiosperm DNA C-value data (i.e. 200 first C-value estimates per annum) the present work equals 1·5 years of average global published output; and constitutes over 12 % of the latest 5-year global target set by the Second Plant Genome Size Workshop (see www.kew.org/cval/workshopreport.html). Hopefully, the present example will encourage others to unveil further valuable data which otherwise may lie forever unpublished and unavailable for comparative analyses. PMID:15905300

Substantial soil organic carbon retention along floodplains of mountain streams

NASA Astrophysics Data System (ADS)

Sutfin, Nicholas A.; Wohl, Ellen

2017-07-01

Small, snowmelt-dominated mountain streams have the potential to store substantial organic carbon in floodplain sediment because of high inputs of particulate organic matter, relatively lower temperatures compared with lowland regions, and potential for increased moisture conditions. This work (i) quantifies mean soil organic carbon (OC) content along 24 study reaches in the Colorado Rocky Mountains using 660 soil samples, (ii) identifies potential controls of OC content based on soil properties and spatial position with respect to the channel, and (iii) and examines soil properties and OC across various floodplain geomorphic features in the study area. Stepwise multiple linear regression (adjusted r2 = 0.48, p < 0.001) indicates that percentage of silt and clay, sample depth, percent sand, distance from the channel, and relative elevation from the channel are significant predictors of OC content in the study area. Principle component analysis indicates limited separation between geomorphic floodplain features based on predictors of OC content. A lack of significant differences among floodplain features suggests that the systematic random sampling employed in this study can capture the variability of OC across floodplains in the study area. Mean floodplain OC (6.3 ± 0.3%) is more variable but on average greater than values in uplands (1.5 ± 0.08% to 2.2 ± 0.14%) of the Colorado Front Range and higher than published values from floodplains in other regions, particularly those of larger rivers.

Application of simple mathematical expressions to relate the half-lives of xenobiotics in rats to values in humans.

PubMed

Ward, Keith W; Erhardt, Paul; Bachmann, Kenneth

2005-01-01

Previous publications from GlaxoSmithKline and University of Toledo laboratories convey our independent attempts to predict the half-lives of xenobiotics in humans using data obtained from rats. The present investigation was conducted to compare the performance of our published models against a common dataset obtained by merging the two sets of rat versus human half-life (hHL) data previously used by each laboratory. After combining data, mathematical analyses were undertaken by deploying both of our previous models, namely the use of an empirical algorithm based on a best-fit model and the use of rat-to-human liver blood flow ratios as a half-life correction factor. Both qualitative and quantitative analyses were performed, as well as evaluation of the impact of molecular properties on predictability. The merged dataset was remarkably diverse with respect to physiochemical and pharmacokinetic (PK) properties. Application of both models revealed similar predictability, depending upon the measure of stipulated accuracy. Certain molecular features, particularly rotatable bond count and pK(a), appeared to influence the accuracy of prediction. This collaborative effort has resulted in an improved understanding and appreciation of the value of rats to serve as a surrogate for the prediction of xenobiotic half-lives in humans when clinical pharmacokinetic studies are not possible or practicable.

Low band gap frequencies and multiplexing properties in 1D and 2D mass spring structures

NASA Astrophysics Data System (ADS)

Aly, Arafa H.; Mehaney, Ahmed

2016-11-01

This study reports on the propagation of elastic waves in 1D and 2D mass spring structures. An analytical and computation model is presented for the 1D and 2D mass spring systems with different examples. An enhancement in the band gap values was obtained by modeling the structures to obtain low frequency band gaps at small dimensions. Additionally, the evolution of the band gap as a function of mass value is discussed. Special attention is devoted to the local resonance property in frequency ranges within the gaps in the band structure for the corresponding infinite periodic lattice in the 1D and 2D mass spring system. A linear defect formed of a row of specific masses produces an elastic waveguide that transmits at the narrow pass band frequency. The frequency of the waveguides can be selected by adjusting the mass and stiffness coefficients of the materials constituting the waveguide. Moreover, we pay more attention to analyze the wave multiplexer and DE-multiplexer in the 2D mass spring system. We show that two of these tunable waveguides with alternating materials can be employed to filter and separate specific frequencies from a broad band input signal. The presented simulation data is validated through comparison with the published research, and can be extended in the development of resonators and MEMS verification.

Mechanisms governing the visco-elastic responses of living cells assessed by foam and tensegrity models.

PubMed

Cañadas, P; Laurent, V M; Chabrand, P; Isabey, D; Wendling-Mansuy, S

2003-11-01

The visco-elastic properties of living cells, measured to date by various authors, vary considerably, depending on the experimental methods and/or on the theoretical models used. In the present study, two mechanisms thought to be involved in cellular visco-elastic responses were analysed, based on the idea that the cytoskeleton plays a fundamental role in cellular mechanical responses. For this purpose, the predictions of an open unit-cell model and a 30-element visco-elastic tensegrity model were tested, taking into consideration similar properties of the constitutive F-actin. The quantitative predictions of the time constant and viscosity modulus obtained by both models were compared with previously published experimental data obtained from living cells. The small viscosity modulus values (10(0)-10(3) Pa x s) predicted by the tensegrity model may reflect the combined contributions of the spatially rearranged constitutive filaments and the internal tension to the overall cytoskeleton response to external loading. In contrast, the high viscosity modulus values (10(3)-10(5) Pa x s) predicted by the unit-cell model may rather reflect the mechanical response of the cytoskeleton to the bending of the constitutive filaments and/or to the deformation of internal components. The present results suggest the existence of a close link between the overall visco-elastic response of micromanipulated cells and the underlying architecture.

Testing Dissipative Magnetosphere Model Light Curves and Spectra with Fermi Pulsars

NASA Technical Reports Server (NTRS)

Brambilla, Gabriele; Kalapotharakos, Constantinos; Harding, Alice K.; Kazanas, Demosthenes

2015-01-01

We explore the emission properties of a dissipative pulsar magnetosphere model introduced by Kalapotharakos et al. comparing its high-energy light curves and spectra, due to curvature radiation, with data collected by the Fermi LAT. The magnetosphere structure is assumed to be near the force-free solution. The accelerating electric field, inside the light cylinder (LC), is assumed to be negligible, while outside the LC it rescales with a finite conductivity (sigma). In our approach we calculate the corresponding high-energy emission by integrating the trajectories of test particles that originate from the stellar surface, taking into account both the accelerating electric field components and the radiation reaction forces. First, we explore the parameter space assuming different value sets for the stellar magnetic field, stellar period, and conductivity. We show that the general properties of the model are in a good agreement with observed emission characteristics of young gamma-ray pulsars, including features of the phase-resolved spectra. Second, we find model parameters that fit each pulsar belonging to a group of eight bright pulsars that have a published phase-resolved spectrum. The sigma values that best describe each of the pulsars in this group show an increase with the spin-down rate (E? ) and a decrease with the pulsar age, expected if pair cascades are providing the magnetospheric conductivity. Finally, we explore the limits of our analysis and suggest future directions for improving such models.

Myocardial Mapping With Cardiac Magnetic Resonance: The Diagnostic Value of Novel Sequences.

PubMed

Sanz, Javier; LaRocca, Gina; Mirelis, Jesús G

2016-09-01

Cardiac magnetic resonance has evolved into a crucial modality for the evaluation of cardiomyopathy due to its ability to characterize myocardial structure and function. In the last few years, interest has increased in the potential of "mapping" techniques that provide direct and objective quantification of myocardial properties such as T1, T2, and T2* times. These approaches enable the detection of abnormalities that affect the myocardium in a diffuse fashion and/or may be too subtle for visual recognition. This article reviews the current state of myocardial T1 and T2-mapping in both health and disease. Copyright © 2016 Sociedad Española de Cardiología. Published by Elsevier España, S.L.U. All rights reserved.

[Anticancer drugs: Which prices for therapeutic innovations?].

PubMed

Gonçalves, Anthony; Maraninchi, Dominique; Marino, Patricia

2016-04-01

The expanding knowledge of the biological mechanisms underlying tumor development made it possible the recent emergence of new therapeutic approaches that are considered as undoubtedly innovative. Yet, to define and to evaluate the magnitude of a drug innovation require an examination of its intrinsic drug properties, medical utility as well as its mode of emergence. Recently, international academic societies, such as ESMO and ASCO, have proposed practical tools that may help quantifying the medical value of a given innovation. Currently, the sustained flux of therapeutic innovations in oncology is associated with an unprecedented growth of costs, the actual determinants of which remain under debate, but raising the critical issue of drugs pricing, and their potential individual or societal "financial toxicity". Copyright © 2016. Published by Elsevier Masson SAS.

Assessment of the Density Functional Tight Binding Method for Protic Ionic Liquids

PubMed Central

2015-01-01

Density functional tight binding (DFTB), which is ∼100–1000 times faster than full density functional theory (DFT), has been used to simulate the structure and properties of protic ionic liquid (IL) ions, clusters of ions and the bulk liquid. Proton affinities for a wide range of IL cations and anions determined using DFTB generally reproduce G3B3 values to within 5–10 kcal/mol. The structures and thermodynamic stabilities of n-alkyl ammonium nitrate clusters (up to 450 quantum chemical atoms) predicted with DFTB are in excellent agreement with those determined using DFT. The IL bulk structure simulated using DFTB with periodic boundary conditions is in excellent agreement with published neutron diffraction data. PMID:25328497

Chemical properties and oxidative stability of Arjan (Amygdalus reuteri) kernel oil as emerging edible oil.

PubMed

Tavakoli, Javad; Emadi, Teymour; Hashemi, Seyed Mohammad Bagher; Mousavi Khaneghah, Amin; Munekata, Paulo Eduardo Sichetti; Lorenzo, Jose Manuel; Brnčić, Mladen; Barba, Francisco J

2018-05-01

The oxidative stability, as well as the chemical composition of Amygdalus reuteri kernel oil (ARKO), were evaluated and compared to those of Amygdalus scoparia kernel oil (ASKO) and extra virgin olive oil (EVOO) during and after holding in the oven (170 °C for 8 h). The oxidative stability analysis was carried out by measuring the changes in conjugated dienes, carbonyl and acid values as well as oil/oxidative stability index and their correlation with the antioxidant compounds (tocopherol, polyphenols, and sterol compounds). The oleic acid was determined as the predominant fatty acid of ARKO (65.5%). Calculated oxidizability value and an iodine value of ARKO, ASKO and EVOO were reported as 3.29 and 3.24, 2.00 and 100.0, 101.4 and 81.9, respectively. Due to the high wax content (4.5% and 3.3%, respectively), the saponification number of ARKO and ASKO (96.4 and 99.8, respectively) was lower than that of EVOO (169.7). ARKO had the highest oxidative stability, followed by ASKO and EVOO. Therefore, ARKO can be introduced as a new source of edible oil with high oxidative stability. Copyright © 2018. Published by Elsevier Ltd.

Analysis of three tests of the unconfined aquifer in southern Nassau County, Long Island, New York

USGS Publications Warehouse

Lindner, J.B.; Reilly, T.E.

1982-01-01

Drawdown and recovery data from three 2-day aquifer tests (OF) the unconfined (water-table) aquifer in southern Nassau County, N.Y., during the fall of 1979, were analyzed. Several simple analytical solutions, a typecurve-matching procedure, and a Galerkin finite-element radial-flow model were used to determine hydraulic conductivity, ratio of horizontal to vertical hydraulic conductivity, and specific yield. Results of the curve-matching procedure covered a broad range of values that could be narrowed through consideration of data from other sources such as published reports, drillers ' logs, or values determined by analytical solutions. Analysis by the radial-flow model was preferred because it allows for vertical variability in aquifer properties and solves the system for all observation points simultaneously, whereas the other techniques treat the aquifer as homogeneous and must treat each observation well separately. All methods produced fairly consistent results. The ranges of aquifer values at the three sites were: horizontal hydraulic conductivity, 140 to 380 feet per day; transmissivity 11,200 to 17,100 feet squared per day; ratio of horizontal to vertical hydraulic conductivity 2.4:1 to 7:1, and specific yield , 0.13 to 0.23. (USGS)

Silica-volatile interaction and the geological cause of the Xuan Wei lung cancer epidemic

DOE Office of Scientific and Technical Information (OSTI.GOV)

David J. Large; Shona Kelly; Baruch Spiro

2009-12-01

Parts of Xuan Wei County, Yunnan Province, China have the highest known lung cancer mortality in nonsmoking women. This high mortality displays a clear spatial relationship to the mines producing coal from the uppermost Permian. Geochemical, petrographic, and grain size analyses were undertaken on a set of coal samples from Xuan Wei. Results demonstrate that the single geochemical property that makes this coal unusual is its high concentration of quartz (13.5 wt %) of which 35-55% occurs as < 10 {mu}m grains. We propose the potential for silica-volatile interaction (PSVI) as a new method for assessing the combined influence ofmore » silica and volatile organic matter and use this as a basis for re-evaluating existing ecological data. Published lung cancer mortality values are more strongly correlated with PSVI values for Xuan Wei coal than with volatiles or silica alone and the PSVI values measured are distinct from those of other coals. Finally we propose that the localization of this epidemic to Xuan Wei results from enhanced weathering of the local Emeishan basalts as a consequence of geochemical perturbations at the Permo-Triassic Boundary.« less

GTA weld penetration and the effects of deviations in machine variables

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giedt, W.H.

1987-07-01

Analytical models for predicting the temperature distribution during GTA welding are reviewed with the purpose of developing a procedure for investigating the effects of deviations in machine parameters. The objective was to determine the accuracy required in machine settings to obtain reproducible results. This review revealed a wide range of published values (21 to 90%) for the arc heating efficiency. Low values (21 to 65%) were associated with evaluation of efficiency using constant property conduction models. Values from 75 to 90% were determined from calorimetric type measurements and are applicable for more accurate numerical solution procedures. Although numerical solutions canmore » yield better overall weld zone predictions, calculations are lengthy and complex. In view of this and the indication that acceptable agreement with experimental measurements can be achieved with the moving-point-source solution, it was utilized to investigate the effects of deviations or errors in voltage, current, and travel speed on GTA weld penetration. Variations resulting from welding within current goals for voltage (+-0.1 V), current (+-3.0 A), and travel speed (+-2.0%) were found to be +-2 to 4%, with voltage and current being more influential than travel speed.« less

Capturing anharmonicity in a lattice thermal conductivity model for high-throughput predictions

DOE PAGES

Miller, Samuel A.; Gorai, Prashun; Ortiz, Brenden R.; ...

2017-01-06

High-throughput, low-cost, and accurate predictions of thermal properties of new materials would be beneficial in fields ranging from thermal barrier coatings and thermoelectrics to integrated circuits. To date, computational efforts for predicting lattice thermal conductivity (κ L) have been hampered by the complexity associated with computing multiple phonon interactions. In this work, we develop and validate a semiempirical model for κ L by fitting density functional theory calculations to experimental data. Experimental values for κ L come from new measurements on SrIn 2O 4, Ba 2SnO 4, Cu 2ZnSiTe 4, MoTe 2, Ba 3In 2O 6, Cu 3TaTe 4, SnO,more » and InI as well as 55 compounds from across the published literature. Here, to capture the anharmonicity in phonon interactions, we incorporate a structural parameter that allows the model to predict κ L within a factor of 1.5 of the experimental value across 4 orders of magnitude in κ L values and over a diverse chemical and structural phase space, with accuracy similar to or better than that of computationally more expensive models.« less

26 CFR 1.1019-1 - Property on which lessee has made improvements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Basis Rules of General Application § 1.1019-1 Property on... value of such property attributable to such buildings or improvements, the basis of each portion of such... building would have a depreciated value of $50,000, which value the lessor elected to report (beginning in...

Yogurt made from milk heated at different pH values.

PubMed

Ozcan, Tulay; Horne, David S; Lucey, John A

2015-10-01

Milk for yogurt manufacture is subjected to high heat treatment to denature whey proteins. Low milk pH values (≤ 6.5) at heating result in most denatured whey proteins becoming associated with casein micelles, whereas high milk pH values (≥ 7.0) at heating result in the formation of mostly soluble (nonmicellar) denatured whey protein complexes. There are conflicting reports on the relative importance of soluble and casein-bound whey protein aggregates on the properties of acid gels. Prior studies investigating the effect of pH of milk at heating used model gels in which milk was acidified by glucono-δ-lactone; in this study, we prepared yogurt gels using commercial starter cultures. Model acid gels can have very different texture and physical properties from those made by fermentation with starter cultures. In this study, we investigated the effects of different pH values of milk at heating on the rheological, light backscatter, and microstructural properties of yogurt gels. Reconstituted skim milk was adjusted to pH values 6.2, 6.7, and 7.2 and heated at 85°C for 30 min. A portion of the heated milk samples was readjusted back to pH 6.7 after heating. Milks were inoculated with 3% (wt/wt) yogurt starter culture and incubated at 40°C until pH 4.6. Gel formation was monitored using dynamic oscillatory rheology, and parameters measured included the storage modulus (G') and loss tangent (LT) values. Light-backscattering properties, such as the backscatter ratio (R) and the first derivative of light backscatter ratio (R'), were also monitored during fermentation. Fluorescence microscopy was used to observe gel microstructure. The G' values at pH 4.6 were highest in gels made from milk heated at pH 6.7 and lowest in milk heated at pH 6.2, with or without pH adjustment after heating. The G' values at pH 4.6 were lower in samples after adjustment back to pH 6.7 after heating. No maximum in the LT parameter was observed during gelation for yogurts made from milk heated at pH 6.2; a maximum in LT was observed at pH ~4.8 for samples heated at pH 6.7 or 7.2, with or without pH adjustment after heating. Higher R-values were observed with an increase in pH of heating, with or without pH adjustment after heating. The sample heated at pH 6.2 had only one major peak in its R' profile during acidification, whereas samples heated at pH 6.7 and 7.2 had 2 large peaks. The lack of a maximum in LT parameter and the presence of a single peak in the R' profile for the samples heated at pH 6.2 were likely due to the partial solubilization of insoluble calcium phosphate when milk was acidified to this lower pH value. No clear differences were observed in the microstructures of gels between the different treatments. This study indicates that heating milk at the natural pH (~6.7) created an optimum balance of casein-bound and soluble denatured whey proteins, which resulted in yogurt with the highest gel stiffness. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The Changing Business of Scholarly Publishing.

ERIC Educational Resources Information Center

Hunter, Karen

1993-01-01

Discussion of changes and trends in scholarly publishing highlights monographs; journals; user-centered publishing; electronic products and services, including adding value, marketing strategies, and new pricing systems; changing attitudes regarding copyright; trends in publishing industry reorganization; and impacts on research libraries. (LRW)

Dose equivalent rate constants and barrier transmission data for nuclear medicine facility dose calculations and shielding design.

PubMed

Kusano, Maggie; Caldwell, Curtis B

2014-07-01

A primary goal of nuclear medicine facility design is to keep public and worker radiation doses As Low As Reasonably Achievable (ALARA). To estimate dose and shielding requirements, one needs to know both the dose equivalent rate constants for soft tissue and barrier transmission factors (TFs) for all radionuclides of interest. Dose equivalent rate constants are most commonly calculated using published air kerma or exposure rate constants, while transmission factors are most commonly calculated using published tenth-value layers (TVLs). Values can be calculated more accurately using the radionuclide's photon emission spectrum and the physical properties of lead, concrete, and/or tissue at these energies. These calculations may be non-trivial due to the polyenergetic nature of the radionuclides used in nuclear medicine. In this paper, the effects of dose equivalent rate constant and transmission factor on nuclear medicine dose and shielding calculations are investigated, and new values based on up-to-date nuclear data and thresholds specific to nuclear medicine are proposed. To facilitate practical use, transmission curves were fitted to the three-parameter Archer equation. Finally, the results of this work were applied to the design of a sample nuclear medicine facility and compared to doses calculated using common methods to investigate the effects of these values on dose estimates and shielding decisions. Dose equivalent rate constants generally agreed well with those derived from the literature with the exception of those from NCRP 124. Depending on the situation, Archer fit TFs could be significantly more accurate than TVL-based TFs. These results were reflected in the sample shielding problem, with unshielded dose estimates agreeing well, with the exception of those based on NCRP 124, and Archer fit TFs providing a more accurate alternative to TVL TFs and a simpler alternative to full spectral-based calculations. The data provided by this paper should assist in improving the accuracy and tractability of dose and shielding calculations for nuclear medicine facility design.

Some physical and functional properties of finger millet (Eleusine coracana) obtained in sub-Saharan Africa.

PubMed

Ramashia, S E; Gwata, E T; Meddows-Taylor, S; Anyasi, T A; Jideani, A I O

2018-02-01

The study determined the physical properties of finger millet (FM) (Eluesine coracana) grains and the functional properties of FM flour. Physical properties such as colour attributes, sample weight, bulk density, true density, porosity, surface area, sample volume, aspect ratio, sphericity, dimensional properties and moisture content of grain cultivars were determined. Water absorption capacity (WAC), bulk density (BD), dispersibility, viscosity and micro-structure of FM flours were also evaluated. Data collected were analyzed using SPSS statistical software version 23.0. Results showed that milky cream cultivar was significantly higher (p<0.05) than other samples in sample weight, bulk density, true density, aspect ratio and sphericity. However, pearl millet, used as a control, was significantly different from FM flour on all dimensional properties. Moisture content of milky cream showed higher significant difference for both grains and flours as compared to brown and black grain/flours. Milky cream cultivar was significantly different in L*, b*, C*, H* values, WAC, BD and dispersibility for both FM grains and flours. Data showed that brown flour was significantly higher in viscosity than in milky and black flours. Microstructure results revealed that starch granules of raw FM flours had oval/spherical and smooth surface. The study is important for agricultural and food engineers, designers, scientists and processors in the design of equipment for FM grain processing. Results are likely to be useful in assessing the quality of grains used to fortify FM flour. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

A Value-Added Framework for Analyzing Electronic and Print Publishing.

ERIC Educational Resources Information Center

Perritt, Henry H., Jr.

1991-01-01

Discusses changes in the publishing industry resulting from digital electronic networks and optical storage technologies, and explains attributes of information products as types of value for both print and electronic contexts. Electronic products necessary for a shift from paper to electronic formats are identified, and legal issues are…

Predicting Reactive Intermediate Quantum Yields from Dissolved Organic Matter Photolysis Using Optical Properties and Antioxidant Capacity.

PubMed

Mckay, Garrett; Huang, Wenxi; Romera-Castillo, Cristina; Crouch, Jenna E; Rosario-Ortiz, Fernando L; Jaffé, Rudolf

2017-05-16

The antioxidant capacity and formation of photochemically produced reactive intermediates (RI) was studied for water samples collected from the Florida Everglades with different spatial (marsh versus estuarine) and temporal (wet versus dry season) characteristics. Measured RI included triplet excited states of dissolved organic matter ( 3 DOM*), singlet oxygen ( 1 O 2 ), and the hydroxyl radical ( • OH). Single and multiple linear regression modeling were performed using a broad range of extrinsic (to predict RI formation rates, R RI ) and intrinsic (to predict RI quantum yields, Φ RI ) parameters. Multiple linear regression models consistently led to better predictions of R RI and Φ RI for our data set but poor prediction of Φ RI for a previously published data set,1 probably because the predictors are intercorrelated (Pearson's r > 0.5). Single linear regression models were built with data compiled from previously published studies (n ≈ 120) in which E2:E3, S, and Φ RI values were measured, which revealed a high degree of similarity between RI-optical property relationships across DOM samples of diverse sources. This study reveals that • OH formation is, in general, decoupled from 3 DOM* and 1 O 2 formation, providing supporting evidence that 3 DOM* is not a • OH precursor. Finally, Φ RI for 1 O 2 and 3 DOM* correlated negatively with antioxidant activity (a surrogate for electron donating capacity) for the collected samples, which is consistent with intramolecular oxidation of DOM moieties by 3 DOM*.

PROPERTIES OF THE T8.5 DWARF WOLF 940 B

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leggett, S. K.; Saumon, D.; Burningham, Ben

We present 7.5-14.2 {mu}m low-resolution spectroscopy, obtained with the Spitzer Infrared Spectrograph, of the T8.5 dwarf Wolf 940 B, which is a companion to an M4 dwarf with a projected separation of 400 AU. We combine these data with previously published near-infrared spectroscopy and mid-infrared photometry to produce the spectral energy distribution for the very low temperature T dwarf. We use atmospheric models to derive the bolometric correction and obtain a luminosity of log L/L{sub sun} = -6.01 {+-} 0.05 (the observed spectra make up 47% of the total flux). Evolutionary models are used with the luminosity to constrain themore » values of effective temperature (T{sub eff}) and surface gravity and hence mass and age for the T dwarf. We ensure that the spectral models used to determine the bolometric correction have T{sub eff} and gravity values consistent with the luminosity-implied values. We further restrict the allowed range of T{sub eff} and gravity using age constraints implied by the M dwarf primary and refine the physical properties of the T dwarf by comparison of the observed and modeled spectroscopy and photometry. This comparison indicates that Wolf 940 B has a metallicity within {approx}0.2 dex of solar, as more extreme values give poor fits to the data-lower metallicity produces a poor fit at {lambda}>2 {mu}m, while higher metallicity produces a poor fit at {lambda} < 2 {mu}m. This is consistent with the independently derived value of [m/H] =+0.24 {+-} 0.09 for the primary star, using the Johnson and Apps M{sub K} : V - K relationship. We find that the T dwarf atmosphere is undergoing vigorous mixing, with an eddy diffusion coefficient K{sub zz} of 10{sup 4} to 10{sup 6} cm{sup 2} s{sup -1}. We derive an effective temperature of 585 K to 625 K, and surface gravity log g = 4.83 to 5.22 (cm s{sup -2}), for an age range of 3 Gyr to 10 Gyr, as implied by the kinematic and H{alpha} properties of the M dwarf primary. Gravity and temperature are correlated such that the lower gravity corresponds to the lower temperature and younger age for the system and the higher values to the higher temperature and older age. The mass of the T dwarf is 24 M{sub Jupiter} to 45 M{sub Jupiter} for the younger to older age limit.« less

Advancing secondary metabolite biosynthesis in yeast with synthetic biology tools.

PubMed

Siddiqui, Michael S; Thodey, Kate; Trenchard, Isis; Smolke, Christina D

2012-03-01

Secondary metabolites are an important source of high-value chemicals, many of which exhibit important pharmacological properties. These valuable natural products are often difficult to synthesize chemically and are commonly isolated through inefficient extractions from natural biological sources. As such, they are increasingly targeted for production by biosynthesis from engineered microorganisms. The budding yeast species Saccharomyces cerevisiae has proven to be a powerful microorganism for heterologous expression of biosynthetic pathways. S. cerevisiae's usefulness as a host organism is owed in large part to the wealth of knowledge accumulated over more than a century of intense scientific study. Yet many challenges are currently faced in engineering yeast strains for the biosynthesis of complex secondary metabolite production. However, synthetic biology is advancing the development of new tools for constructing, controlling, and optimizing complex metabolic pathways in yeast. Here, we review how the coupling between yeast biology and synthetic biology is advancing the use of S. cerevisiae as a microbial host for the construction of secondary metabolic pathways. © 2011 Federation of European Microbiological Societies. Published by Blackwell Publishing Ltd. All rights reserved.

[Diastolic dysfunction in the elderly subjects. Disease or a physiological manifestation of ageing?].

PubMed

Meluzín, J; Podroužková, H; Gregorová, Z; Panovský, R

2013-05-01

The purpose of this summary paper is to discuss the current knowledge of the impact of age on diastolic function of the left ventricle. Data from the literature: Reports published till this time have convincingly demonstrated a significant relationship of age to diastolic function of the left ventricle. Ageing is a physiological process accompanied by structural changes in both myocardium and arterial bed resulting in worsening of parameters characterizing the left ventricular diastolic function. This "physiological" diastolic dysfunction in the elderly subjects can be explained by the deterioration of passive left ventricular filling properties and by worsening of left ventricular relaxation. The detailed analysis of published reports shows problems in distiguishing this "physiological" diastolic dysfunction resulting from physiological tissue ageing from "pathological" diastolic dysfunction reflecting a disease of cardiovascular system. To interprete correctly values of parameters quantifying diastolic function of the left ventricle, one should take into account the age of subjects under the examination. Further studies are necessary to distinguish exactly "physiological" deterioration of diastolic function associated with ageing from really "pathological" diastolic dysfunction in the elderly subjects.

The multidirectional bending properties of the human lumbar intervertebral disc.

PubMed

Spenciner, David; Greene, David; Paiva, James; Palumbo, Mark; Crisco, Joseph

2006-01-01

While the biomechanical properties of the isolated intervertebral disc have been well studied in the three principal anatomic directions of flexion/extension, axial rotation, and lateral bending, there is little data on the properties in the more functional directions that are combinations of these principal anatomic directions. To determine the bending flexibility, range of motion (ROM), and neutral zone (NZ) of the human lumbar disc in multiple directions and to determine if the values about the combined moment axes can be predicted from the values about principal moment axes. Three-dimensional biomechanical analysis of the elastic bending properties of human lumbar discs about principal and combined moment axes. Pure, unconstrained moments were applied about multiple axes. The bending properties (flexibility, ROM, and NZ) of isolated lumbar discs (n=4 for L2/L3 and n=3 for L4/L5) were determined in the six principal directions and in 20 combined directions. The experimental values were compared with those predicted from the linear combination of the six principal moment axes. The maximum and minimum values of the biomechanical properties were found at the principal moment axes. Among combined moment axes, ROM and NZ (but not flexibility) values were predicted from the principal moment axis values. The principal moment axes coincide with the primary mechanical axes of the intervertebral disc and demonstrate significant differences in direction for values of flexibility, ROM, and NZ. Not all combined moment axis values can be predicted from principal moment axis values.

12 CFR 614.4265 - Real property evaluations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Real property evaluations. 614.4265 Section 614... Collateral Evaluation Requirements § 614.4265 Real property evaluations. (a) Real estate shall be valued on... property and operation where the transaction value exceeds $250,000 and the real estate taken as collateral...

12 CFR 614.4265 - Real property evaluations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 7 2013-01-01 2013-01-01 false Real property evaluations. 614.4265 Section 614... Collateral Evaluation Requirements § 614.4265 Real property evaluations. (a) Real estate shall be valued on... property and operation where the transaction value exceeds $250,000 and the real estate taken as collateral...

12 CFR 614.4265 - Real property evaluations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 7 2012-01-01 2012-01-01 false Real property evaluations. 614.4265 Section 614... Collateral Evaluation Requirements § 614.4265 Real property evaluations. (a) Real estate shall be valued on... property and operation where the transaction value exceeds $250,000 and the real estate taken as collateral...

12 CFR 614.4265 - Real property evaluations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 7 2014-01-01 2014-01-01 false Real property evaluations. 614.4265 Section 614... Collateral Evaluation Requirements § 614.4265 Real property evaluations. (a) Real estate shall be valued on... property and operation where the transaction value exceeds $250,000 and the real estate taken as collateral...

12 CFR 614.4265 - Real property evaluations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 6 2011-01-01 2011-01-01 false Real property evaluations. 614.4265 Section 614... Collateral Evaluation Requirements § 614.4265 Real property evaluations. (a) Real estate shall be valued on... property and operation where the transaction value exceeds $250,000 and the real estate taken as collateral...

2 CFR 215.36 - Intangible property.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... This “recorded” material excludes physical objects (e.g., laboratory samples). Research data also do... person in a research study. (ii) Published is defined as either when: (A) Research findings are published... Information Act (FOIA) request for research data relating to published research findings produced under an...

2 CFR 215.36 - Intangible property.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... This “recorded” material excludes physical objects (e.g., laboratory samples). Research data also do... person in a research study. (ii) Published is defined as either when: (A) Research findings are published... Information Act (FOIA) request for research data relating to published research findings produced under an...

2 CFR 215.36 - Intangible property.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... This “recorded” material excludes physical objects (e.g., laboratory samples). Research data also do... person in a research study. (ii) Published is defined as either when: (A) Research findings are published... Information Act (FOIA) request for research data relating to published research findings produced under an...

Fracture Micromechanics of Intermetallic and Ceramic Matrix Continuous Fiber Composites

DTIC Science & Technology

1991-05-01

mechanical properties of titanium matrix composites, but much less information has been published. Only data in the published literature is referenced in...1984, pp. 1931-1940. 18. C.J. Yang, S.M. Jeng and J.-M. Yang " Interfacial properties measurements for SiC fiber-reinforced titanium alloy composites...Analyses of these parameters allowed a determination of interfacial shear strength. Fracture mechanics was used to correlate the micromechanical

26 CFR 1.707-6 - Disguised sales of property by partnership to partner; general rules.

Code of Federal Regulations, 2013 CFR

2013-04-01

... transferred property to the partner; by (B) The excess of the fair market value of the property at the time it... property X to A. At the time of the transfer, property X has a fair market value of $1,000,000. One year... similar to those provided in § 1.707-3 apply in determining whether a transfer of property by a...

26 CFR 1.707-6 - Disguised sales of property by partnership to partner; general rules.

Code of Federal Regulations, 2012 CFR

2012-04-01

... transferred property to the partner; by (B) The excess of the fair market value of the property at the time it... property X to A. At the time of the transfer, property X has a fair market value of $1,000,000. One year... similar to those provided in § 1.707-3 apply in determining whether a transfer of property by a...

26 CFR 1.684-2 - Transfers.

Code of Federal Regulations, 2010 CFR

2010-04-01

... decides to transfer additional property with a fair market value of 1000X and an adjusted basis of 600X to... fair market value of 1000X and an adjusted basis of 300X to I, a foreign person. On January 1, 2007, at a time when the fair market value of the property is 1100X, I transfers the property to FT. A is...

Tissue material properties and computational modelling of the human tibiofemoral joint: a critical review

PubMed Central

Akhtar, Riaz; Comerford, Eithne J.; Bates, Karl T.

2018-01-01

Understanding how structural and functional alterations of individual tissues impact on whole-joint function is challenging, particularly in humans where direct invasive experimentation is difficult. Finite element (FE) computational models produce quantitative predictions of the mechanical and physiological behaviour of multiple tissues simultaneously, thereby providing a means to study changes that occur through healthy ageing and disease such as osteoarthritis (OA). As a result, significant research investment has been placed in developing such models of the human knee. Previous work has highlighted that model predictions are highly sensitive to the various inputs used to build them, particularly the mathematical definition of material properties of biological tissues. The goal of this systematic review is two-fold. First, we provide a comprehensive summation and evaluation of existing linear elastic material property data for human tibiofemoral joint tissues, tabulating numerical values as a reference resource for future studies. Second, we review efforts to model tibiofemoral joint mechanical behaviour through FE modelling with particular focus on how studies have sourced tissue material properties. The last decade has seen a renaissance in material testing fuelled by development of a variety of new engineering techniques that allow the mechanical behaviour of both soft and hard tissues to be characterised at a spectrum of scales from nano- to bulk tissue level. As a result, there now exists an extremely broad range of published values for human tibiofemoral joint tissues. However, our systematic review highlights gaps and ambiguities that mean quantitative understanding of how tissue material properties alter with age and OA is limited. It is therefore currently challenging to construct FE models of the knee that are truly representative of a specific age or disease-state. Consequently, recent tibiofemoral joint FE models have been highly generic in terms of material properties even relying on non-human data from multiple species. We highlight this by critically evaluating current ability to quantitatively compare and model (1) young and old and (2) healthy and OA human tibiofemoral joints. We suggest that future research into both healthy and diseased knee function will benefit greatly from a subject- or cohort-specific approach in which FE models are constructed using material properties, medical imagery and loading data from cohorts with consistent demographics and/or disease states. PMID:29379690

Tissue material properties and computational modelling of the human tibiofemoral joint: a critical review.

PubMed

Peters, Abby E; Akhtar, Riaz; Comerford, Eithne J; Bates, Karl T

2018-01-01

Understanding how structural and functional alterations of individual tissues impact on whole-joint function is challenging, particularly in humans where direct invasive experimentation is difficult. Finite element (FE) computational models produce quantitative predictions of the mechanical and physiological behaviour of multiple tissues simultaneously, thereby providing a means to study changes that occur through healthy ageing and disease such as osteoarthritis (OA). As a result, significant research investment has been placed in developing such models of the human knee. Previous work has highlighted that model predictions are highly sensitive to the various inputs used to build them, particularly the mathematical definition of material properties of biological tissues. The goal of this systematic review is two-fold. First, we provide a comprehensive summation and evaluation of existing linear elastic material property data for human tibiofemoral joint tissues, tabulating numerical values as a reference resource for future studies. Second, we review efforts to model tibiofemoral joint mechanical behaviour through FE modelling with particular focus on how studies have sourced tissue material properties. The last decade has seen a renaissance in material testing fuelled by development of a variety of new engineering techniques that allow the mechanical behaviour of both soft and hard tissues to be characterised at a spectrum of scales from nano- to bulk tissue level. As a result, there now exists an extremely broad range of published values for human tibiofemoral joint tissues. However, our systematic review highlights gaps and ambiguities that mean quantitative understanding of how tissue material properties alter with age and OA is limited. It is therefore currently challenging to construct FE models of the knee that are truly representative of a specific age or disease-state. Consequently, recent tibiofemoral joint FE models have been highly generic in terms of material properties even relying on non-human data from multiple species. We highlight this by critically evaluating current ability to quantitatively compare and model (1) young and old and (2) healthy and OA human tibiofemoral joints. We suggest that future research into both healthy and diseased knee function will benefit greatly from a subject- or cohort-specific approach in which FE models are constructed using material properties, medical imagery and loading data from cohorts with consistent demographics and/or disease states.

Measure of microhardness, fracture toughness and flexural strength of N-vinylcaprolactam (NVC)-containing glass-ionomer dental cements.

PubMed

Moshaverinia, Alireza; Brantley, William A; Chee, Winston W L; Rohpour, Nima; Ansari, Sahar; Zheng, Fengyuan; Heshmati, Reza H; Darr, Jawwad A; Schricker, Scott R; Rehman, Ihtesham U

2010-12-01

To investigate the effects of N-vinylcaprolactam (NVC)-containing terpolymers on the fracture toughness, microhardness, and flexural strength of conventional glass-ionomer cements (GIC). The terpolymer of acrylic acid (AA)-itaconic acid (IA)-N-vinylcaprolactam (NVC) with 8:1:1 (AA:IA:NVC) molar ratio was synthesized by free radical polymerization and characterized using (1)H NMR and FTIR. Experimental GIC samples were made from a 50% solution of the synthesized terpolymer with Fuji IX powder in a 3.6:1 P/L ratio. Specimens were mixed and fabricated at room temperature. Plane strain fracture toughness (K(Ic)) was measured in accordance with ASTM Standard 399-05. Vickers hardness was determined using a microhardness tester. Flexural strength was measured using samples with dimensions of 2 mm×2 mm×20 mm. For all mechanical property tests, specimens were first conditioned in distilled water at 37°C for 1 day or 1 week. Fracture toughness and flexural strength tests were conducted on a screw-driven universal testing machine using a crosshead speed of 0.5mm/min. Values of mechanical properties for the experimental GIC were compared with the control group (Fuji IX GIC), using one-way ANOVA and the Tukey multiple range test at α=0.05. The NVC-modified GIC exhibited significantly higher fracture toughness compared to the commercially available Fuji IX GIC, along with higher mean values of flexural strength and Vickers hardness, which were not significantly different. It was concluded that NVC-containing polymers are capable of enhancing clinically relevant properties for GICs. This new modified glass-ionomer is a promising restorative dental material. Copyright © 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Reinforcement of flowable dental composites with titanium dioxide nanotubes.

PubMed

Dafar, Manal O; Grol, Matthew W; Canham, Peter B; Dixon, S Jeffrey; Rizkalla, Amin S

2016-06-01

Flowable dental composites are used as restorative materials due to their excellent esthetics and rheology. However, they suffer from inferior mechanical properties compared to conventional composites. The aim of this study was to reinforce a flowable dental composite with TiO2 nanotubes (n-TiO2) and to assess the effect of n-TiO2 surface modifications on the mechanical properties of the reinforced composite. n-TiO2 were synthesized using an alkaline hydrothermal process and then functionalized with silane or methacrylic acid (MA). Nanotubes were characterized by scanning and transmission electron microscopy, X-ray diffraction, energy-dispersive X-ray spectroscopy and Fourier transform infrared spectroscopy. Commercially available flowable composite (Filtek™ Supreme Ultra Flowable Restorative, 3M ESPE) was reinforced with varying amounts of nanotubes (0-5wt%). Flowability of the resulting composites was evaluated using a Gillmore needle method. Dynamic Young's modulus (E) was measured using an ultrasonic technique. Fracture toughness (KIc) was assessed using a notchless triangular prism and radiopacity was quantified. Viability of NIH/3T3 fibroblasts was evaluated following incubation on composite specimens for 24h. Electron microscopy revealed a tubular morphology of n-TiO2. All reinforced composites exhibited significantly greater values of E than unreinforced composite. Composites reinforced with 3wt% n-TiO2 functionalized with MA exhibited the greatest values of E and KIc. Cytotoxicity assays revealed that reinforced composites were biocompatible. Taken together, flowable composites reinforced with n-TiO2 exhibited mechanical properties superior to those of unreinforced composite, with minimal effects on flowability and radiopacity. n-TiO2-reinforced flowable composites are promising materials for use in dental restorations. Copyright © 2016 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Mechanically-competent and cytocompatible polycaprolactone-borophosphosilicate hybrid biomaterials.

PubMed

Mondal, Dibakar; Dixon, S Jeffrey; Mequanint, Kibret; Rizkalla, Amin S

2017-11-01

Organic-inorganic class II hybrid materials have domain sizes at the molecular level and chemical bonding between the organic and inorganic phases. We have previously reported the synthesis of class II hybrid biomaterials from alkoxysilane-functionalized polycaprolactone (PCL) and borophosphosilicate (B 2 O 3 -P 2 O 5 -SiO 2 ) glass (BPSG) through a non-aqueous sol-gel process. In the present study, the mechanical properties and degradability of these PCL/BPSG hybrid biomaterials were studied and compared to those of their conventional composite counterparts. The compressive strength, modulus and toughness of the hybrid biomaterials were significantly greater compared to the conventional composites, likely due to the covalent bonding between the organic and inorganic phases. A hybrid biomaterial (50wt% PCL and 50wt% BPSG) exhibited compressive strength, modulus and toughness values of 32.2 ± 3.5MPa, 573 ± 85MPa and 1.54 ± 0.03MPa, respectively; whereas the values for composite of similar composition were 18.8 ± 1.6MPa, 275 ± 28MPa and 0.76 ± 0.03MPa, respectively. Degradation in phosphate-buffered saline was slower for hybrid biomaterials compared to their composite counterparts. Thus, these hybrid materials possess superior mechanical properties and more controlled degradation characteristics compared to their corresponding conventional composites. To assess in vitro cytocompatibility, MC3T3-E1 pre-osteoblastic cells were seeded onto the surfaces of hybrid biomaterials and polycaprolactone (control). Compared to polycaprolactone, cells on the hybrid material displayed enhanced spreading, focal adhesion formation, and cell number, consistent with excellent cytocompatibility. Thus, based on their mechanical properties, degradability and cytocompatibility, these novel biomaterials have potential for use as scaffolds in bone tissue engineering and related applications. Copyright © 2017. Published by Elsevier Ltd.

Phase transformation behavior and mechanical properties of thermomechanically treated K3XF nickel-titanium instruments.

PubMed

Shen, Ya; Zhou, Hui-Min; Wang, Zhejun; Campbell, Les; Zheng, Yu-feng; Haapasalo, Markus

2013-07-01

The bending and torsional properties of thermomechanically treated K3XF (SybronEndo, Orange, CA) nickel-titanium instruments in relation to their phase transformation behavior were evaluated. NiTi instruments K3 (SybronEndo) and K3XF, both in sizes 25/.04 and 40/.04, were examined by differential scanning calorimetry and X-ray diffraction. The metal composition was determined by scanning electron microscopy with X-ray energy-dispersive spectrometric analyses. The bending property of K3 and K3XF instruments was measured in a cantilever-bending test with a maximum deflection of 4.00 mm. A torsional test of the instruments was evaluated according to the American National Standards Institute/American Dental Association Specification No. 28. K3 and K3XF instruments had approximately the same chemical composition with a nickel content of 48-49 atomic %. The differential scanning calorimetry analyses showed that each segment of the K3XF instruments (24.89°C ± 1.98°C) had a higher austenite finish temperature than the K3 instruments (17.63°C ± 1.76°C) (P < .05). The bending load values were significantly lower for K3XF than for K3 in the superelastic ranges (P < .05). There was no statistically significant difference between K3 and K3XF in the maximum torque or maximum angular deflection before failure. The torque at fracture values of K3 and K3XF increased significantly with the diameter (P < .05). K3XF exhibited different phase transformation behavior and flexibility when compared with K3, which may be attributed to the special heat treatment history of K3XF instruments. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

RCSED—A Value-added Reference Catalog of Spectral Energy Distributions of 800,299 Galaxies in 11 Ultraviolet, Optical, and Near-infrared Bands: Morphologies, Colors, Ionized Gas, and Stellar Population Properties

NASA Astrophysics Data System (ADS)

Chilingarian, Igor V.; Zolotukhin, Ivan Yu.; Katkov, Ivan Yu.; Melchior, Anne-Laure; Rubtsov, Evgeniy V.; Grishin, Kirill A.

2017-02-01

We present RCSED, the value-added Reference Catalog of Spectral Energy Distributions of galaxies, which contains homogenized spectrophotometric data for 800,299 low- and intermediate-redshift galaxies (0.007< z< 0.6) selected from the Sloan Digital Sky Survey spectroscopic sample. Accessible from the Virtual Observatory (VO) and complemented with detailed information on galaxy properties obtained with state-of-the-art data analysis, RCSED enables direct studies of galaxy formation and evolution over the last 5 Gyr. We provide tabulated color transformations for galaxies of different morphologies and luminosities, and analytic expressions for the red sequence shape in different colors. RCSED comprises integrated k-corrected photometry in up to 11 ultraviolet, optical, and near-infrared bands published by the GALEX, SDSS, and UKIDSS wide-field imaging surveys; results of the stellar population fitting of SDSS spectra including best-fitting templates, velocity dispersions, parameterized star formation histories, and stellar metallicities computed for instantaneous starburst and exponentially declining star formation models; parametric and non-parametric emission line fluxes and profiles; and gas phase metallicities. We link RCSED to the Galaxy Zoo morphological classification and galaxy bulge+disk decomposition results of Simard et al. We construct the color-magnitude, Faber-Jackson, and mass-metallicity relations; compare them with the literature; and discuss systematic errors of the galaxy properties presented in our catalog. RCSED is accessible from the project web site and via VO simple spectrum access and table access services using VO-compliant applications. We describe several examples of SQL queries to the database. Finally, we briefly discuss existing and future scientific applications of RCSED and prospective catalog extensions to higher redshifts and different wavelengths. .

Modestobacter caceresii sp. nov., novel actinobacteria with an insight into their adaptive mechanisms for survival in extreme hyper-arid Atacama Desert soils.

PubMed

Busarakam, Kanungnid; Bull, Alan T; Trujillo, Martha E; Riesco, Raul; Sangal, Vartul; van Wezel, Gilles P; Goodfellow, Michael

2016-06-01

A polyphasic study was designed to determine the taxonomic provenance of three Modestobacter strains isolated from an extreme hyper-arid Atacama Desert soil. The strains, isolates KNN 45-1a, KNN 45-2b(T) and KNN 45-3b, were shown to have chemotaxonomic and morphological properties in line with their classification in the genus Modestobacter. The isolates had identical 16S rRNA gene sequences and formed a branch in the Modestobacter gene tree that was most closely related to the type strain of Modestobacter marinus (99.6% similarity). All three isolates were distinguished readily from Modestobacter type strains by a broad range of phenotypic properties, by qualitative and quantitative differences in fatty acid profiles and by BOX fingerprint patterns. The whole genome sequence of isolate KNN 45-2b(T) showed 89.3% average nucleotide identity, 90.1% (SD: 10.97%) average amino acid identity and a digital DNA-DNA hybridization value of 42.4±3.1 against the genome sequence of M. marinus DSM 45201(T), values consistent with its assignment to a separate species. On the basis of all of these data, it is proposed that the isolates be assigned to the genus Modestobacter as Modestobacter caceresii sp. nov. with isolate KNN 45-2b(T) (CECT 9023(T)=DSM 101691(T)) as the type strain. Analysis of the whole-genome sequence of M. caceresii KNN 45-2b(T), with 4683 open reading frames and a genome size of ∽4.96Mb, revealed the presence of genes and gene-clusters that encode for properties relevant to its adaptability to harsh environmental conditions prevalent in extreme hyper arid Atacama Desert soils. Copyright © 2016. Published by Elsevier GmbH.

45 CFR 74.36 - Intangible property.

Code of Federal Regulations, 2014 CFR

2014-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 2543.36 - Intangible property.

Code of Federal Regulations, 2013 CFR

2013-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 2543.36 - Intangible property.

Code of Federal Regulations, 2014 CFR

2014-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 2543.36 - Intangible property.

Code of Federal Regulations, 2010 CFR

2010-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 74.36 - Intangible property.

Code of Federal Regulations, 2011 CFR

2011-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 74.36 - Intangible property.

Code of Federal Regulations, 2010 CFR

2010-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 74.36 - Intangible property.

Code of Federal Regulations, 2012 CFR

2012-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 74.36 - Intangible property.

Code of Federal Regulations, 2013 CFR

2013-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 2543.36 - Intangible property.

Code of Federal Regulations, 2011 CFR

2011-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

45 CFR 2543.36 - Intangible property.

Code of Federal Regulations, 2012 CFR

2012-10-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed... Information Act (FOIA) request for research data relating to published research findings produced under an...

The Property Value Protection Program - How the Compensation Plan is Working and Evolving to Meet Changing Needs - 13149

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faught, Jeff; Herod, Judy; Mahabir, Alexandra

2013-07-01

The Property Value Protection (PVP) Program offers an innovative approach to address the risk of individual property value loss resulting from the cleanup and long-term management of historic low level radioactive waste in the Port Hope area in Southern Ontario, Canada. This cleanup is taking place through the Port Hope Area Initiative (PHAI), a federally sponsored waste remediation project. The PVP Program came into effect on October 1, 2000, having been established as a key element of the PHAI Legal Agreement between the Government of Canada and the municipalities of Port Hope and Clarington. The PVP Program was designed inmore » direct response to the concern expressed by the agreement's two municipal signatories that protection of local property owners from the risk of property value loss was critical to their acceptance of the Port Hope and Port Granby projects. The PVP Program compensates owners of residential, commercial or industrial properties for a loss in fair market value on the sale or rental of their properties. Increased mortgage refinancing costs and expenses incurred as a result of delayed sales that can be attributed to the Port Hope Area Initiative are also compensated. (authors)« less

26 CFR 1.707-6 - Disguised sales of property by partnership to partner; general rules.

Code of Federal Regulations, 2010 CFR

2010-04-01

... transferred property to the partner; by (B) The excess of the fair market value of the property at the time it... property X to A. At the time of the transfer, property X has a fair market value of $1,000,000. One year... provided in § 1.707-3 apply in determining whether a transfer of property by a partnership to a partner and...

Quantifying the costs and benefits of privacy-preserving health data publishing.

PubMed

Khokhar, Rashid Hussain; Chen, Rui; Fung, Benjamin C M; Lui, Siu Man

2014-08-01

Cost-benefit analysis is a prerequisite for making good business decisions. In the business environment, companies intend to make profit from maximizing information utility of published data while having an obligation to protect individual privacy. In this paper, we quantify the trade-off between privacy and data utility in health data publishing in terms of monetary value. We propose an analytical cost model that can help health information custodians (HICs) make better decisions about sharing person-specific health data with other parties. We examine relevant cost factors associated with the value of anonymized data and the possible damage cost due to potential privacy breaches. Our model guides an HIC to find the optimal value of publishing health data and could be utilized for both perturbative and non-perturbative anonymization techniques. We show that our approach can identify the optimal value for different privacy models, including K-anonymity, LKC-privacy, and ∊-differential privacy, under various anonymization algorithms and privacy parameters through extensive experiments on real-life data. Copyright © 2014 Elsevier Inc. All rights reserved.

Trends in P Value, Confidence Interval, and Power Analysis Reporting in Health Professions Education Research Reports: A Systematic Appraisal.

PubMed

Abbott, Eduardo F; Serrano, Valentina P; Rethlefsen, Melissa L; Pandian, T K; Naik, Nimesh D; West, Colin P; Pankratz, V Shane; Cook, David A

2018-02-01

To characterize reporting of P values, confidence intervals (CIs), and statistical power in health professions education research (HPER) through manual and computerized analysis of published research reports. The authors searched PubMed, Embase, and CINAHL in May 2016, for comparative research studies. For manual analysis of abstracts and main texts, they randomly sampled 250 HPER reports published in 1985, 1995, 2005, and 2015, and 100 biomedical research reports published in 1985 and 2015. Automated computerized analysis of abstracts included all HPER reports published 1970-2015. In the 2015 HPER sample, P values were reported in 69/100 abstracts and 94 main texts. CIs were reported in 6 abstracts and 22 main texts. Most P values (≥77%) were ≤.05. Across all years, 60/164 two-group HPER studies had ≥80% power to detect a between-group difference of 0.5 standard deviations. From 1985 to 2015, the proportion of HPER abstracts reporting a CI did not change significantly (odds ratio [OR] 2.87; 95% CI 1.04, 7.88) whereas that of main texts reporting a CI increased (OR 1.96; 95% CI 1.39, 2.78). Comparison with biomedical studies revealed similar reporting of P values, but more frequent use of CIs in biomedicine. Automated analysis of 56,440 HPER abstracts found 14,867 (26.3%) reporting a P value, 3,024 (5.4%) reporting a CI, and increased reporting of P values and CIs from 1970 to 2015. P values are ubiquitous in HPER, CIs are rarely reported, and most studies are underpowered. Most reported P values would be considered statistically significant.

Consumer willingness to pay for pharmacy services: An updated review of the literature.

PubMed

Painter, Jacob T; Gressler, Laura; Kathe, Niranjan; Slabaugh, S Lane; Blumenschein, Karen

2018-02-02

Quantifying the value of pharmacy services is imperative for the profession as it works to establish an expanded role within evolving health care systems. The literature documents the work that many have contributed toward meeting this goal. To date, however, the preponderance of evidence evaluates the value of pharmacist services to third-party payers; few published studies address the value that consumers place on these services. In 1999, a review of studies that used the contingent valuation method to value pharmacy services was published. The objective of this manuscript is to provide an update of that review. Relevant studies published in the English language were identified searching MEDLINE, ECONLIT and International Pharmaceutical Abstracts databases from January 1999 to November 2017. Only studies that specifically elicited willingness to pay for a community pharmacist provided service from actual or potential consumers were included. Thirty-one studies using the contingent valuation method to value pharmacy services were identified using the search strategy outlined. These studies included surveys in different demographic and geographic populations and valuing various pharmacy services. Improving the quality of studies using contingent valuation to value pharmacy services will aid the profession in marketing pharmacy services to consumers, and may assist practitioners who wish to implement various pharmacy services in their practice settings. A limited number of studies have been conducted, but the quality of contingent valuation studies valuing pharmacist services is improving. Understanding the pharmacy services that consumers value, and understanding the level of their monetary willingness to pay for those services will be crucial as the profession continues to work toward establishing a sustainable and economically viable role within the evolving health care systems. Copyright © 2018. Published by Elsevier Inc.

26 CFR 1.1245-1 - General rule for treatment of gain from dispositions of certain depreciable property.

Code of Federal Regulations, 2010 CFR

2010-04-01

... property and the non-section 1245 property in proportion to their respective fair market values. In general... fair market value of $3,700, thereby realizing a gain of $1,700 ($3,700 amount realized minus $2,000... gain to which section 1245(a)(1) applies is the amount by which (i) the lower of the fair market value...

7 CFR 356.4 - Property valued at $10,000 or less; notice of seizure administrative action to obtain forfeiture.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Property valued at $10,000 or less; notice of seizure... PROCEDURES § 356.4 Property valued at $10,000 or less; notice of seizure administrative action to obtain... notice of seizure and proposed forfeiture as provided in paragraph (c)(1) of this section, by posting for...

RI: Rheology as a Tool for Understanding the Mechanics of Live Ant Aggregations, Part 1

DTIC Science & Technology

2016-11-04

measure rheological properties of biological fluids. Using this machine, we were able to characterize non -Newtonian fluids such as frog saliva...GA 30332 -0420 ABSTRACT Number of Papers published in peer-reviewed journals: Number of Papers published in non peer-reviewed journals: Final Report...order to measure rheological properties of biological fluids. Using this machine, we were able to characterize non -Newtonian fluids such as frog

Exploring the influence of texture and composition on the thermal transport properties of mudstones

NASA Astrophysics Data System (ADS)

Kenderes, S. M.; Hofmeister, A. M.; Merriman, J. D.; Whittington, A. G.

2017-12-01

The thermal history of sedimentary basins depends strongly on the thermal transport properties of the rocks within the basin. Mudstones are compositionally diverse, varying both chemically and with modal mineralogy, which are known to affect the thermal transport properties of earth materials. To explore the influence of composition and texture on the thermal transport properties of mudstones, we have measured the thermal diffusivity (D) and isobaric heat capacity (CP) of 12 mudstones using the contact-free laser flash analysis (LFA) and differential scanning calorimetry (DSC). At 20°C, D values of the shales range from 0.318 to 1.214 mm2·s-1 and CP values range from 799 to 918 J·kg-1·°C-1 and at 300°C, D values range from 0.227 to 0.582 mm2·s-1 and CP values range from 1095 to 1344 J·kg-1·°C-1. The mudstones with the highest D values, and lowest CP values are green micaceous or calcareous siltstones respectively, whereas the mudstones with the lowest D values, and highest CP values are black, claystones with 9% organic carbon. This suggests that organic carbon content and, to a lesser extent, the grainsize influence the thermal transport properties of these rocks. The lower D values and higher CP values cause organic rich claystones to absorb and transmit heat differently than other types of mudstones. This is especially true at lower temperatures, where the difference in D values is much greater than at higher temperatures. Additionally, when compared to other sedimentary rocks, shales generally have lower D values and higher CP values. These results also highlight the necessity of using rock type specific values in heat transport numerical models.

24 CFR 84.36 - Intangible property.

Code of Federal Regulations, 2012 CFR

2012-04-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed...) request for research data relating to published research findings produced under an award that were used...

24 CFR 84.36 - Intangible property.

Code of Federal Regulations, 2013 CFR

2013-04-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed...) request for research data relating to published research findings produced under an award that were used...

24 CFR 84.36 - Intangible property.

Code of Federal Regulations, 2014 CFR

2014-04-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed...) request for research data relating to published research findings produced under an award that were used...

24 CFR 84.36 - Intangible property.

Code of Federal Regulations, 2010 CFR

2010-04-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed...) request for research data relating to published research findings produced under an award that were used...

24 CFR 84.36 - Intangible property.

Code of Federal Regulations, 2011 CFR

2011-04-01

...” material excludes physical objects (e.g., laboratory samples). Research data also do not include: (A) Trade... study. (ii) Published is defined as either when: (A) Research findings are published in a peer-reviewed...) request for research data relating to published research findings produced under an award that were used...

A Spanish version of the Skin Cancer Index: a questionnaire for measuring quality of life in patients with cervicofacial nonmelanoma skin cancer.

PubMed

de Troya-Martín, M; Rivas-Ruiz, F; Blázquez-Sánchez, N; Fernández-Canedo, I; Aguilar-Bernier, M; Repiso-Jiménez, J B; Toribio-Montero, J C; Jones-Caballero, M; Rhee, J

2015-01-01

The Skin Cancer Index (SCI) is the first specific patient-reported outcome measure for patients with cervicofacial nonmelanoma skin cancer. To date, only the original English version has been published. To develop a Spanish version of the SCI that is semantically and linguistically equivalent to the original, and to evaluate its measurement properties in this different cultural environment. A cross-sectional study was conducted of the cultural adaptation and empirical validation of the questionnaire, analysing the psychometric properties of the new index at different stages. Of 440 patients recruited to the study, 431 (95%) completed the Spanish version of the SCI questionnaire, in a mean time of 6·3 min (SD 2·9). Factor analysis of the scale revealed commonality and loading values of < 0·5 for three of the 15 items. The remaining 12 items converged into two components: appearance/social aspects (seven items) and emotional aspects (five items). Both domains presented a high level of internal consistency, with Cronbach's alpha values above 0·8. The convergent-discriminant validity analysis produced correlations higher than 0·3 for the mental component of the Short Form Health Survey-12v2 Health Questionnaire (correlation coefficient 0·39) and the Dermatology Quality of Life Index (correlation coefficient -0·30). In the test-retest, nine of the 12 items produced a weighted kappa value exceeding 0·4, and for the remaining three items, the absolute agreement percentage exceeded 60%. The Spanish version of the SCI quality of life scale has been satisfactorily adapted and validated for use in Spanish-speaking countries and populations. © 2014 British Association of Dermatologists.

The Impact of Electronic Commerce on the Publishing Industry: Towards a Business Value Complementarity Framework of Electronic Publishing.

ERIC Educational Resources Information Center

Scupola, Ada

1999-01-01

Discussion of the publishing industry and its use of information and communication technologies focuses on the way in which electronic-commerce technologies are changing and could change the publishing processes, and develops a business complementarity model of electronic publishing to maximize profitability and improve the competitive position.…

21 CFR 1316.74 - Appraisement.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 9 2011-04-01 2011-04-01 false Appraisement. 1316.74 Section 1316.74 Food and... appraise the property to determine the domestic value at the time and place of seizure. The domestic value... no market for the property at the place of seizure, the domestic value shall be considered the value...

21 CFR 1316.74 - Appraisement.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Appraisement. 1316.74 Section 1316.74 Food and... appraise the property to determine the domestic value at the time and place of seizure. The domestic value... no market for the property at the place of seizure, the domestic value shall be considered the value...

26 CFR 1.1001-1 - Computation of gain or loss.

Code of Federal Regulations, 2010 CFR

2010-04-01

... fair market value of any property (other than money) received. The fair market value of property is a... market value of the contingent payments payable on the debt instrument. If a debt instrument subject to... increased by the fair market value of the contingent payments payable on the debt instrument. This paragraph...

41 CFR 101-6.2103 - What programs and activities of GSA are subject to these regulations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true What programs and... Property Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS...? The Administrator publishes in the Federal Register a list of GSA's programs and activities that are...

Thermoelectric Properties of Selenides Spinels

NASA Technical Reports Server (NTRS)

Snyder, G.; Caillat, T.; Fleurial, J-P.

2000-01-01

Many compounds with the spinel structure type have been analyzed for their thermoelectric properties. Published data was used to augment experimental results presented here to select promising thermoelectric spinels.

No evidential value in samples of transcranial direct current stimulation (tDCS) studies of cognition and working memory in healthy populations.

PubMed

Medina, Jared; Cason, Samuel

2017-09-01

A substantial number of studies have been published over the last decade, claiming that transcranial direct current stimulation (tDCS) can influence performance on cognitive tasks. However, there is some skepticism regarding the efficacy of tDCS, and evidence from meta-analyses are mixed. One major weakness of these meta-analyses is that they only examine outcomes in published studies. Given biases towards publishing positive results in the scientific literature, there may be a substantial "file-drawer" of unpublished negative results in the tDCS literature. Furthermore, multiple researcher degrees of freedom can also inflate published p-values. Recently, Simonsohn, Nelson and Simmons (2014) created a novel meta-analytic tool that examines the distribution of significant p-values in a literature, and compares it to expected distributions with different effect sizes. Using this tool, one can assess whether the selected studies have evidential value. Therefore, we examined a random selection of studies that used tDCS to alter performance on cognitive tasks, and tDCS studies on working memory in a recently published meta-analysis (Mancuso et al., 2016). Using a p-curve analysis, we found no evidence that the tDCS studies had evidential value (33% power or greater), with the estimate of statistical power of these studies being approximately 14% for the cognitive studies, and 5% (what would be expected from randomly generated data) for the working memory studies. It is likely that previous tDCS studies are substantially underpowered, and we provide suggestions for future research to increase the evidential value of future tDCS studies. Copyright © 2017 Elsevier Ltd. All rights reserved.

Dynamic mechanical thermal properties of the dental light-cured nanohybrid composite Kalore, GC: effect of various food/oral simulating liquids.

PubMed

Sideridou, Irini D; Vouvoudi, Evangelia C; Adamidou, Evanthia A

2015-02-01

The aim of this work is the study of the dynamic mechanical thermal properties (viscoelastic properties) of a current dental commercial light-cured nanohybrid resin composite, Kalore, GC (GC Corporation, Tokyo, Japan) along with the study of the effect of some food/oral simulating liquids (FSLs) on these properties. Dynamic mechanical thermal analysis (DMTA) tests were performed on a Diamond Dynamic Mechanical Thermal Analyzer in bending mode. A frequency of 1Hz and a temperature range of 25-185°C were applied, while the heating rate of 2°C/min was selected to cover mouth temperature and the material's likely Tg. The properties were determined after storage in air, distilled water, heptane, ethanol/water solution (75% v/v) or absolute ethanol at 37°C for up to 1h, 1, 7 or 30 days. Storage modulus, loss modulus and tangent delta (tanδ) were plotted against temperature. The glass transition temperatures are taken from the peak of the tangent tanδ versus temperature curves. Moreover, some factors indicating the heterogeneity of the polymer matrix, such as the width (ΔT) at the half of tanδ peak and the "ζ" parameter were determined. All samples analyzed after storage for 1h or 1 day in the aging media showed two Tg values. All samples analyzed after storage for 7 or 30 days in the ageing media showed a unique Tg value. Storage of Kalore GC in dry air, water or heptane at 37°C for 7 days caused post-curing reactions. Storage in air or water for 30 days did not seem to cause further effects. Storage in heptane for 30 days may cause plasticization and probably some degradation of the filler-silane bond and polymer matrix. Storage in ethanol/water solution (75% v/v) or ethanol for 7 days seems to cause post-curing reactions and degradation reactions of the matrix-filler bonds. Storage in ethanol for 30 days caused a strong change of the sample morphology and the DMTA results were not reliable. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

26 CFR 1.817-3 - Gain on property held on December 31, 1958, and certain substituted property acquired after 1958.

Code of Federal Regulations, 2012 CFR

2012-04-01

... REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED... (iii) The fair market value of the property on December 31, 1958, exceeds the adjusted basis for... regard to section 817(b)(1)) exceeds the difference between fair market value of such property on...

26 CFR 1.817-3 - Gain on property held on December 31, 1958, and certain substituted property acquired after 1958.

Code of Federal Regulations, 2013 CFR

2013-04-01

... REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED... (iii) The fair market value of the property on December 31, 1958, exceeds the adjusted basis for... regard to section 817(b)(1)) exceeds the difference between fair market value of such property on...

Surface Characterization of Nanomaterials and Nanoparticles. Important needs and challenging opportunities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baer, Donald R.; Engelhard, Mark H.; Johnson, Grant E.

2013-08-27

This review examines the characterization challenges inherently associated with understanding nanomaterials and how surface characterization methods can help meet those challenges. In parts of the research community, there is growing recognition that many studies and published reports on the properties and behaviors of nanomaterials have involved inadequate characterization. As a consequence, the true value of the data in these reports is, at best, uncertain. As the importance of nanomaterials in fundamental research and technological applications increases, it is necessary for researchers to recognize the challenges associated with reproducible materials synthesis, maintaining desired materials properties during handling and processing, and themore » dynamic nature of nanomaterials, especially nanoparticles. Researchers also need to understand how characterization approaches (surface and otherwise) can be used to minimize synthesis surprises and to determine how (and how quickly) materials and properties change in different environments. The types of information that can be provided by traditional surface sensitive analysis methods (including X-ray photoelectron and Auger electron spectroscopies, scanning probe microscopy and secondary ion mass spectroscopy) and less common or evolving surface sensitive methods (e.g., nuclear magnetic resonance, sum frequency generation, and low and medium energy ion scattering) are discussed and various of their use in nanomaterial research are presented.« less

RNA as a stable polymer to build controllable and defined nanostructures for material and biomedical applications

PubMed Central

Li, Hui; Lee, Taek; Dziubla, Thomas; Pi, Fengmei; Guo, Sijin; Xu, Jing; Li, Chan; Haque, Farzin; Liang, Xing-Jie; Guo, Peixuan

2015-01-01

Summary The value of polymers is manifested in their vital use as building blocks in material and life sciences. Ribonucleic acid (RNA) is a polynucleic acid, but its polymeric nature in materials and technological applications is often overlooked due to an impression that RNA is seemingly unstable. Recent findings that certain modifications can make RNA resistant to RNase degradation while retaining its authentic folding property and biological function, and the discovery of ultra-thermostable RNA motifs have adequately addressed the concerns of RNA unstability. RNA can serve as a unique polymeric material to build varieties of nanostructures including nanoparticles, polygons, arrays, bundles, membrane, and microsponges that have potential applications in biomedical and material sciences. Since 2005, more than a thousand publications on RNA nanostructures have been published in diverse fields, indicating a remarkable increase of interest in the emerging field of RNA nanotechnology. In this review, we aim to: delineate the physical and chemical properties of polymers that can be applied to RNA; introduce the unique properties of RNA as a polymer; review the current methods for the construction of RNA nanostructures; describe its applications in material, biomedical and computer sciences; and, discuss the challenges and future prospects in this field. PMID:26770259

Know the Planet, Know the Star: Precise Stellar Densities from Kepler Transit Light Curves

NASA Astrophysics Data System (ADS)

Sandford, Emily; Kipping, David

2017-12-01

The properties of a transiting planet’s host star are written in its transit light curve. The light curve can reveal the stellar density ({ρ }* ) and the limb-darkening profile in addition to the characteristics of the planet and its orbit. For planets with strong prior constraints on orbital eccentricity, we may measure these stellar properties directly from the light curve; this method promises to aid greatly in the characterization of transiting planet host stars targeted by the upcoming NASA Transiting Exoplanet Survey Satellite mission and any long-period, singly transiting planets discovered in the same systems. Using Bayesian inference, we fit a transit model, including a nonlinear limb-darkening law, to 66 Kepler transiting planet hosts to measure their stellar properties. We present posterior distributions of ρ *, limb-darkening coefficients, and other system parameters for these stars. We measure densities to within 5% for the majority of our target stars, with the dominant precision-limiting factor being the signal-to-noise ratio of the transits. Of our measured stellar densities, 95% are in 3σ or better agreement with previously published literature values. We make posterior distributions for all of our target Kepler objects of interest available online at 10.5281/zenodo.1028515.

Comparison of dosimetric properties among four commercial multi-detector computed tomography scanners.

PubMed

Ohno, Takeshi; Araki, Fujio; Onizuka, Ryota; Hatemura, Masahiro; Shimonobou, Toshiaki; Sakamoto, Takashi; Okumura, Shuichiro; Ideguchi, Daichi; Honda, Keiichi; Kawata, Kenji

2017-03-01

This study compared dosimetric properties among four commercial multi-detector CT (MDCT) scanners. The X-ray beam characteristics were obtained from photon intensity attenuation curves of aluminum and off-center ratio (OCR) profiles in air, which were measured with four commercial MDCT scanners. The absorbed dose for MDCT scanners was evaluated with Farmer ionization chamber measurements at the center and four peripheral points in the body- and head-type cylindrical water phantoms. Measured collected charge was converted to absorbed dose using a 60 Co absorbed dose-to-water calibration factor and Monte Carlo (MC)-calculated correction factors. Four MDCT scanners were modeled to correspond with measured X-ray beam characteristics using GMctdospp (IMPS, Germany) software. Al half-value layers (Al-HVLs) with a body-bowtie filter determined from measured Al-attenuation curves ranged 7.2‒9.1mm at 120kVp and 6.1‒8.0mm at 100kVp. MC-calculated Al-HVLs and OCRs in air were in acceptable agreement within 0.5mm and 5% of measured values, respectively. The percentage difference between nominal and actual beam width was greater with decreasing collimation width. The absorbed doses for MDCT scanners at 120kVp ranged 5.1‒7.1mGy and 10.8‒17.5mGy per 100mAs at the center in the body- and head-type water phantoms, respectively. Measured doses at four peripheral points were within 5% agreement of MC-calculated values. The absorbed dose at the center in both water phantoms increased with decreasing Al-HVL for the same charge on the focus. In this study the X-ray beam characteristics and the absorbed dose were measured and compared with calculated values for four MDCT scanners. Copyright © 2017 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

26 CFR 20.2010-2T - Portability provisions applicable to estate of a decedent survived by a spouse (temporary).

Code of Federal Regulations, 2014 CFR

2014-04-01

... executor is not required to report a value for such property on the estate tax return (except to the extent... with regard to establishing the value of the property) and the instructions for the estate tax return... tax return and § 20.2056(a)-1(b) (except with regard to establishing the value of the property). In...

26 CFR 20.2010-2T - Portability provisions applicable to estate of a decedent survived by a spouse (temporary).

Code of Federal Regulations, 2013 CFR

2013-04-01

... executor is not required to report a value for such property on the estate tax return (except to the extent... with regard to establishing the value of the property) and the instructions for the estate tax return... tax return and § 20.2056(a)-1(b) (except with regard to establishing the value of the property). In...

Measurement of mechanical and thermophysical properties of dimensionally stable materials for space applications

NASA Technical Reports Server (NTRS)

Rawal, Suraj P.; Misra, Mohan S.

1992-01-01

Mechanical, thermal, and physical property test data was generated for as-fabricated advanced composite materials at room temperature (RT), -150 and 250 F. The results are documented of mechanical and thermophysical property tests of IM7/PEEK and discontinuous SiC/Al (particulate (p) and whisker (w) reinforced) composites which were tested at three different temperatures to determine the effect of temperature on material properties. The specific material systems tested were IM7/PEEK (0)8, (0, + or - 45, 90)s, (+ or - 30, 04)s, 25 vol. pct. (v/o) SiCp/Al, and 25 v/o SiCw/Al. RT material property results of IM7/PEEK were in good agreement with the predicted values, providing a measure of consolidation integrity attained during fabrication. Results of mechanical property tests indicated that modulus values at each test temperature were identical, whereas the strength (e.g., tensile, compressive, flexural, and shear) values were the same at -150 F, and RT, and gradually decreased as the test temperature was increased to 250 F. Similar trends in the strength values was also observed in discontinuous SiC/Al composites. These results indicate that the effect of temperature was more pronounced on the strength values than modulus values.

Lactic acid concentrations that reduce microbial load yet minimally impact colour and sensory characteristics of beef.

PubMed

Rodríguez-Melcón, Cristina; Alonso-Calleja, Carlos; Capita, Rosa

2017-07-01

Lactic acid (LA) has recently been approved in the EU as beef decontaminant. In order to identify the most appropriate concentration, beef samples were spray-treated with LA (2%, 3%, 4% or 5%) or left untreated (control). Microbial load (aerobic plate counts, psychrotrophs and Enterobacteriaceae), pH, instrumental colour and sensory properties were investigated at 0, 24, 72 and 120h of refrigerated storage. The reductions in bacteria after spraying ranged from 0.57 to 0.95 log units. A residual antimicrobial effect was observed so that at 120h LA reduced microbial load by up to 2 log units compared with the control samples. Samples treated with 5% LA showed the lowest redness value (a*) and hedonic scores at all sampling times. Only for samples treated with 4% LA did the sensorial shelf-life limit extend beyond 120h. It is suggested that treatment of beef with 4% LA not only may improve microbiological quality, but also may enhance sensory properties and shelf-life. Copyright © 2017. Published by Elsevier Ltd.

Reliability, validity and responsiveness of the Spanish Manchester-Oxford Foot Questionnaire (MOXFQ) in patients with foot or ankle surgery.

PubMed

Garcés, Juan B Gerstner; Winson, Ian; Goldhahn, Sabine; Castro, Michael D; Swords, Michael P; Grujic, Leslie; Rammelt, Stefan; Sands, Andrew K

2016-03-01

The Manchester-Oxford Foot Questionnaire (MOXFQ) has been validated in Spanish for use in patients undergoing foot and ankle surgery. 120 patients completed the MOXFQ and the SF-36 before surgery and 6 and 12 months postoperative. Surgeons completed the American Orthopaedic Foot and Ankle Society (AOFAS) Clinical Rating System. Psychometric properties were assessed for all three MOXFQ dimensions, and for the MOXFQ Index. The Spanish MOXFQ demonstrated consistency with Cronbach's alpha values between 0.65 and 0.90, and reliability ([ICCs] >0.95). It shows a moderate to strong correlation between the Walking/standing dimension and the related domains of the SF-36 (|r|>0.6), the AOFAS Ankle-Hindfoot Scale (|r|>0.47) and Hallux-MTP-IP Scale (|r|>0.64). Responsiveness was excellent, (effect sizes >2.1). The respective minimal detectable change (MDC90) was 14.18 for the MOXFQ Index. The Spanish version of the MOXFQ showed good psychometric properties in patients with foot and ankle disorders. Copyright © 2015 European Foot and Ankle Society. Published by Elsevier Ltd. All rights reserved.

Improving Biopharmaceutical Properties of Vinpocetine Through Cocrystallization.

PubMed

Golob, Samuel; Perry, Miranda; Lusi, Matteo; Chierotti, Michele R; Grabnar, Iztok; Lassiani, Lucia; Voinovich, Dario; Zaworotko, Michael J

2016-12-01

Vinpocetine is a poorly water soluble weakly basic drug (pK a  = 7.1) used for the treatment of several cerebrovascular and cognitive disorders. Because existing formulations exhibit poor bioavailability and scarce absorption, a dosage form with improved pharmacokinetic properties is highly desirable. Cocrystallization represents a promising approach to generate diverse novel crystal forms and to improve the aqueous solubility and in turn the oral bioavailability. In this article, a novel ionic cocrystal of vinpocetine is described, using boric acid as a coformer, and fully characterized (by means of differential scanning calorimetry, solid-state nuclear magnetic resonance, powder and single-crystal X-ray diffraction, and powder dissolution test). Pharmacokinetic performance was also tested in a human pilot study. This pharmaceutical ionic cocrystal exhibits superior solubilization kinetics and modulates important pharmacokinetic values such as maximum concentration in plasma (C max ), time to maximum concentration (t max ), and area under the plasma concentration-time curve (AUC) of the poorly soluble vinpocetine and it therefore offers an innovative approach to improve its bioavailability. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Printability of calcium phosphate powders for three-dimensional printing of tissue engineering scaffolds.

PubMed

Butscher, Andre; Bohner, Marc; Roth, Christian; Ernstberger, Annika; Heuberger, Roman; Doebelin, Nicola; von Rohr, Philipp Rudolf; Müller, Ralph

2012-01-01

Three-dimensional printing (3DP) is a versatile method to produce scaffolds for tissue engineering. In 3DP the solid is created by the reaction of a liquid selectively sprayed onto a powder bed. Despite the importance of the powder properties, there has to date been a relatively poor understanding of the relation between the powder properties and the printing outcome. This article aims at improving this understanding by looking at the link between key powder parameters (particle size, flowability, roughness, wettability) and printing accuracy. These powder parameters are determined as key factors with a predictive value for the final 3DP outcome. Promising results can be expected for mean particle size in the range of 20-35 μm, compaction rate in the range of 1.3-1.4, flowability in the range of 5-7 and powder bed surface roughness of 10-25 μm. Finally, possible steps and strategies in pushing the physical limits concerning improved quality in 3DP are addressed and discussed. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Correlation between classical rheometry and supersonic shear wave imaging in blood clots.

PubMed

Bernal, Miguel; Gennisson, Jean-Luc; Flaud, Patrice; Tanter, Mickael

2013-11-01

The assessment of coagulating blood elasticity has gained importance as a result of several studies that have correlated it to cardiovascular pathologic conditions. In this study we use supersonic shear wave imaging (SSI) to measure viscoelastic properties of blood clots. At the same time, classical rheometry experiments were carried out on the same blood samples taken within the first few seconds of coagulation. Using SSI, phase velocities of the shear wave indicated increasing dispersion with time. In all cases, the frequency bandwidth of propagating shear waves changed from 20-50 Hz at the first few min of coagulation to around 300 Hz toward the end of experiments. Using the values of G' and G″ from the rheometry studies, the theoretical shear wave velocities were calculated and correlated with SSI measurements. Results of the two techniques were in very good agreement, confirming that SSI provides accurate measurements of viscoelastic properties as corroborated by conventional rheometric measurements. Copyright © 2013 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

Ultrasonic extraction of pectin from Opuntia ficus indica cladodes after mucilage removal: Optimization of experimental conditions and evaluation of chemical and functional properties.

PubMed

Bayar, Nadia; Bouallegue, Tahani; Achour, Mabrouka; Kriaa, Mouna; Bougatef, Ali; Kammoun, Radhouane

2017-11-15

Ultrasonic assisted extraction (UAE) of pectin from Opuntia ficus indica (OFI) cladodes after mucilage removal was attempted using the response surface methodology. The process variables were optimized by the isovariant central composite design in order to improve the pectin extraction yield. The optimum condition obtained was: sonication time 70min, temperature 70°C, pH 1.5 and the water-material ratio 30ml/g. This condition was validated and the performance of experimental extraction was 18.14%±1.41%, which was closely linked to the predicted value (19.06%). Thus, UAE present a promising alternative to conventional extraction process thanks to its high efficiency which was achieved in less time and at lower temperatures. The pectin extracted by UAE from OFI cladodes (UAEPC) has a low degree of esterification, high uronic acid content, important functional properties and good anti-radical activity. These results are in favor of the use of UAEPC as potential additive in food industry. Copyright © 2017. Published by Elsevier Ltd.

A Nanoflare-Based Cellular Automaton Model and the Observed Properties of the Coronal Plasma

NASA Technical Reports Server (NTRS)

Lopez-Fuentes, Marcelo; Klimchuk, James Andrew

2016-01-01

We use the cellular automaton model described in Lopez Fuentes and Klimchuk to study the evolution of coronal loop plasmas. The model, based on the idea of a critical misalignment angle in tangled magnetic fields, produces nanoflares of varying frequency with respect to the plasma cooling time. We compare the results of the model with active region (AR) observations obtained with the Hinode/XRT and SDOAIA instruments. The comparison is based on the statistical properties of synthetic and observed loop light curves. Our results show that the model reproduces the main observational characteristics of the evolution of the plasma in AR coronal loops. The typical intensity fluctuations have amplitudes of 10 percent - 15 percent both for the model and the observations. The sign of the skewness of the intensity distributions indicates the presence of cooling plasma in the loops. We also study the emission measure (EM) distribution predicted by the model and obtain slopes in log(EM) versus log(T) between 2.7 and 4.3, in agreement with published observational values.

Characterizing Thermal Properties of Melting Te Semiconductor: Thermal Diffusivity Measurements and Simulation

NASA Technical Reports Server (NTRS)

Zhu, Shen; Li, C.; Su, Ching-Hua; Lin, B.; Ben, H.; Scripa, R. N.; Lehoczky, S. L.; Curreri, Peter A. (Technical Monitor)

2002-01-01

Tellurium is an element for many II-VI and I-III-VI(sub 2) compounds that are useful materials for fabricating many devices. In the melt growth techniques, the thermal properties of the molten phase are important parameter for controlling growth process to improve semiconducting crystal quality. In this study, thermal diffusivity of molten tellurium has been measured by a laser flash method in the temperature range from 500 C to 900 C. A pulsed laser with 1064 nm wavelength is focused on one side of the measured sample. The thermal diffusivity can be estimated from the temperature transient at the other side of the sample. A numerical simulation based on the thermal transport process has been also performed. By numerically fitting the experimental results, both the thermal conductivity and heat capacity can be derived. A relaxation phenomenon, which shows a slow drift of the measured thermal conductivity toward the equilibrium value after cooling of the sample, was observed for the first time. The error analysis and the comparison of the results to published data measured by other techniques will be discussed.

Characterizing Thermal Properties of Melting Te Semiconductor: Thermal Diffusivity Measurements and Simulation

NASA Technical Reports Server (NTRS)

Zhu, Shen; Su, Ching-Hua; Li, C.; Lin, B.; Ben, H.; Scripa, R. N.; Lehoczky, S. L.; Curreri, Peter A. (Technical Monitor)

2002-01-01

Tellurium is an element for many II-VI and I-III-VI(sub 2) compounds that are useful materials for fabricating many devises. In the melt growth techniques, the thermal properties of the molten phase are important parameter for controlling growth process to improve semiconducting crystal quality. In this study, thermal diffusivity of molten tellurium has been measured by a laser flash method in the temperature range from 500 C to 900 C. A pulsed laser with 1064 nm wavelength is focused on one side of the measured sample. The thermal diffusivity can be estimated from the temperature transient at the other side of the sample. A numerical simulation based on the thermal transport process has been also performed. By numerically fitting the experimental results, both the thermal conductivity and heat capacity can be derived. A relaxation phenomenon, which shows a slow drift of the measured thermal conductivity toward the equilibrium value after cooling of the sample, was observed for the first time. The error analysis and the comparison of the results to published data measured by other techniques will be discussed in the presentation.

Extraction, chemical composition, rheological behavior, antioxidant activity and functional properties of Cordia myxa mucilage.

PubMed

Dokht, Shaghayegh Keshani; Djomeh, Zahra Emam; Yarmand, Mohammad Saeid; Fathi, Morteza

2018-06-14

This paper aims to investigate chemical composition, rheological behavior, antioxidant activity and functional properties of Cordia myxa mucilage (CMM). Response surface methodology (RSM) demonstrated that optimum conditions for CMM extraction were as follow: ultrasound power of 99.37 W, extraction temperature of 88.05 °C and solid to water ratio of 16.25 w/w. CMM had, on average, 77.51% carbohydrate, 5.86% total ash, 8.90% protein, 6.90% moisture, and 1.00% fat. Due to a high level of nutrients, CMM can be suggested as a value added by-product in food and pharmaceutical systems. CMM is a low molecular weight polysaccharide containing three fractions with various molecular weights. FT-IR spectrum illustrated that this polymer had all typical bands and peaks characteristics of polysaccharides. Based on steady shear measurements, CMM can be introduced as a new source of hydrocolloid with high-temperature stability. CMM had the desirable antiradical capacity, water solubility and water/oil holding capacity. Copyright © 2017. Published by Elsevier B.V.

A NANOFLARE-BASED CELLULAR AUTOMATON MODEL AND THE OBSERVED PROPERTIES OF THE CORONAL PLASMA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fuentes, Marcelo López; Klimchuk, James A., E-mail: lopezf@iafe.uba.ar

2016-09-10

We use the cellular automaton model described in López Fuentes and Klimchuk to study the evolution of coronal loop plasmas. The model, based on the idea of a critical misalignment angle in tangled magnetic fields, produces nanoflares of varying frequency with respect to the plasma cooling time. We compare the results of the model with active region (AR) observations obtained with the Hinode /XRT and SDO /AIA instruments. The comparison is based on the statistical properties of synthetic and observed loop light curves. Our results show that the model reproduces the main observational characteristics of the evolution of the plasmamore » in AR coronal loops. The typical intensity fluctuations have amplitudes of 10%–15% both for the model and the observations. The sign of the skewness of the intensity distributions indicates the presence of cooling plasma in the loops. We also study the emission measure (EM) distribution predicted by the model and obtain slopes in log(EM) versus log(T) between 2.7 and 4.3, in agreement with published observational values.« less

Martensitic transformation of austenitic stainless steel orthodontic wires during intraoral exposure.

PubMed

Izquierdo, Paula P; de Biasi, Ronaldo S; Elias, Carlos N; Nojima, Lincoln I

2010-12-01

Our purpose was to study the mechanical properties and phase transformations of orthodontic wires submitted to in-vivo exposure in the mouth for different periods of time. Stainless steel wires were tied to fixed orthodontic appliances of 30 patients from the orthodontics clinic of Universidade Federal do Rio de Janeiro School of Dentistry in Brazil. According to the duration of the clinical treatment, the patients were divided into 3 groups. After in-vivo exposure, the samples were studied by mechanical testing (torsion) and ferromagnetic resonance. Statistical analyses were carried out to evaluate the correlation between time of exposure, mechanical properties, and austenite-to-martensite transformation among the groups. The results were compared with as-received control samples. The torque values increased as time in the mouth increased. The increase in torque resistance showed high correlations with time of exposure (P = 0.005) and austenite-martensite phase transformation. The resistance of stainless steel orthodontic wires increases as the time in the mouth increases; this effect is attributed to the austenite-to-martensite transformation. Copyright © 2010 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Erratum: Substructure in clusters of galaxies and the value of {OMEGA}

NASA Astrophysics Data System (ADS)

Dutta, Suvendra N.

1996-05-01

The paper `Substructure in clusters of galaxies and the value of {OMEGA}' was published in Mon. Not. R. Astron. Soc. 276, 1109- 1115(1995). Unfortunately, the wrong set of figures was inadvertently supplied to the publishers after the paper had been accepted. The correct figures are reproduced below, with the corresponding captions. [See Journal].

Subtraction by Distraction: Publishing Value-Added Estimates of Teachers by Name Hinders Education Reform

ERIC Educational Resources Information Center

Epstein, Diana; Miller, Raegen T.

2011-01-01

In August 2010 the "Los Angeles Times" published a special report on their website featuring performance ratings for nearly 6,000 Los Angeles Unified School District teachers. The move was controversial because the ratings were based on so-called value-added estimates of teachers' contributions to student learning. As with most…

36 CFR 1210.32 - Real property.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 1210.32 Parks, Forests, and Public Property NATIONAL ARCHIVES AND RECORDS ADMINISTRATION GENERAL... Government after it compensates the Federal Government for that percentage of the current fair market value... that percentage of the current fair market value of the property attributable to the Federal...

Issues in Electronic Publishing.

ERIC Educational Resources Information Center

Meadow, Charles T.

1997-01-01

Discusses issues related to electronic publishing. Topics include writing; reading; production, distribution, and commerce; copyright and ownership of intellectual property; archival storage; technical obsolescence; control of content; equality of access; and cultural changes. (Author/LRW)

Properties of hydrophobic free energy found by gas–liquid transfer

PubMed Central

Baldwin, Robert L.

2013-01-01

The hydrophobic free energy in current use is based on transfer of alkane solutes from liquid alkanes to water, and it has been argued recently that these values are incorrect and should be based instead on gas–liquid transfer data. Hydrophobic free energy is measured here by gas–liquid transfer of hydrocarbon gases from vapor to water. The new definition reduces more than twofold the values of the apparent hydrophobic free energy. Nevertheless, the newly defined hydrophobic free energy is still the dominant factor that drives protein folding as judged by ΔCp, the change in heat capacity, found from the free energy change for heat-induced protein unfolding. The ΔCp for protein unfolding agrees with ΔCp values for solvating hydrocarbon gases and disagrees with ΔCp for breaking peptide hydrogen bonds, which has the opposite sign. The ΔCp values for the enthalpy of liquid–liquid and gas–liquid transfer are similar. The plot of free energy against the apparent solvent-exposed surface area is given for linear alkanes, but only for a single conformation, the extended conformation, of these flexible-chain molecules. The ability of the gas–liquid hydrophobic factor to predict protein stability is tested and reasonable agreement is found, using published data for the dependences on temperature of the unfolding enthalpy of ribonuclease T1 and the solvation enthalpies of the nonpolar and polar groups. PMID:23319615

Properties of hydrophobic free energy found by gas-liquid transfer.

PubMed

Baldwin, Robert L

2013-01-29

The hydrophobic free energy in current use is based on transfer of alkane solutes from liquid alkanes to water, and it has been argued recently that these values are incorrect and should be based instead on gas-liquid transfer data. Hydrophobic free energy is measured here by gas-liquid transfer of hydrocarbon gases from vapor to water. The new definition reduces more than twofold the values of the apparent hydrophobic free energy. Nevertheless, the newly defined hydrophobic free energy is still the dominant factor that drives protein folding as judged by ΔCp, the change in heat capacity, found from the free energy change for heat-induced protein unfolding. The ΔCp for protein unfolding agrees with ΔCp values for solvating hydrocarbon gases and disagrees with ΔCp for breaking peptide hydrogen bonds, which has the opposite sign. The ΔCp values for the enthalpy of liquid-liquid and gas-liquid transfer are similar. The plot of free energy against the apparent solvent-exposed surface area is given for linear alkanes, but only for a single conformation, the extended conformation, of these flexible-chain molecules. The ability of the gas-liquid hydrophobic factor to predict protein stability is tested and reasonable agreement is found, using published data for the dependences on temperature of the unfolding enthalpy of ribonuclease T1 and the solvation enthalpies of the nonpolar and polar groups.

Managed Retreat in New York after Sandy: Incentivizing Participation in High-Cost Areas

NASA Astrophysics Data System (ADS)

McDonnell, S.; Ghorbani, P.; Wolf, C.; Stovall, G.

2017-12-01

Extreme weather events may potentially displace millions of people worldwide by 2100 (Nicholls et al., 2011). In the US, flood-prone areas are still attractive to many residents (Dyckman, St. John, & London, 2014), and the most common policies such as zoning or subsidized flood insurance continue to incentivize more development (Mechler & Bouwer, 2015). An increasingly popular alternative for mitigating flood damage is managed retreat, which consists of buying out properties in hazardous areas and relocating the owners elsewhere. We explore New York State's buyout program—a $680 million program administered under its Community Development Block Grant-Disaster Recovery (CDBG-DR) allocation—in the aftermath of Superstorm Sandy. Buyouts in New York tend to be costlier because of higher housing prices and density (Lincoln Institute, 2016), and potential participants may face challenges finding comparable housing within their communities. Since buyout offers are based on property values, homeowners with lower net property values may have less incentive to participate. We ask what neighborhood, household, and property characteristics affect the likelihood of participating in the buyout program. Specifically, are lower property values a disincentive to participation? We use binomial and multinomial logistic regression analyses to estimate the likelihood of participation for a sample of 2,062 properties invited to the program. Our main predictor compares the net offer amount against the local median housing value, controlling for an array of household and neighborhood characteristics. We find that relative property values are inversely correlated with participation, more visibly pronounced in areas with larger gaps between applicants' property values and local home values. While CDBG-DR is specifically geared towards lower-income families and neighborhoods, our findings imply that its existing structure may hinder engagement of these target groups in high-cost areas. To attract them, we recommend an incentive structure that rewards clustered participation compared to individual properties. We also recommend that additional incentive be provided to help lower-income applicants stay close to their original neighborhoods.

VALUATION OF CLIMATE RELATED NATURAL AMENITIES IN PROPERTY MARKETS

EPA Science Inventory

Residential property markets reflect the values people assign to environmental amenities. In particular, such values can be examined through hedonic price models. For example, these models can be used to quantify the economic value of specific measures of weather that contribut...

34 CFR 222.23 - How does a local educational agency determine the aggregate assessed value of its eligible...

Code of Federal Regulations, 2010 CFR

2010-07-01

... adding together the assessed values determined pursuant to paragraph (a)(4) of this section for all... Uses for Determining Base Values Tax classifications of adjacent properties based on highest and best... aggregate assessed value of its eligible Federal property for its section 8002 payment? 222.23 Section 222...

34 CFR 222.23 - How does a local educational agency determine the aggregate assessed value of its eligible...

Code of Federal Regulations, 2012 CFR

2012-07-01

... adding together the assessed values determined pursuant to paragraph (a)(4) of this section for all... Uses for Determining Base Values Tax classifications of adjacent properties based on highest and best... aggregate assessed value of its eligible Federal property for its section 8002 payment? 222.23 Section 222...

34 CFR 222.23 - How does a local educational agency determine the aggregate assessed value of its eligible...

Code of Federal Regulations, 2011 CFR

2011-07-01

... adding together the assessed values determined pursuant to paragraph (a)(4) of this section for all... Uses for Determining Base Values Tax classifications of adjacent properties based on highest and best... aggregate assessed value of its eligible Federal property for its section 8002 payment? 222.23 Section 222...

34 CFR 222.23 - How does a local educational agency determine the aggregate assessed value of its eligible...

Code of Federal Regulations, 2013 CFR

2013-07-01

... adding together the assessed values determined pursuant to paragraph (a)(4) of this section for all... Uses for Determining Base Values Tax classifications of adjacent properties based on highest and best... aggregate assessed value of its eligible Federal property for its section 8002 payment? 222.23 Section 222...

34 CFR 222.23 - How does a local educational agency determine the aggregate assessed value of its eligible...

Code of Federal Regulations, 2014 CFR

2014-07-01

... adding together the assessed values determined pursuant to paragraph (a)(4) of this section for all... Uses for Determining Base Values Tax classifications of adjacent properties based on highest and best... aggregate assessed value of its eligible Federal property for its section 8002 payment? 222.23 Section 222...

A new way of setting the phases for cosmological multiscale Gaussian initial conditions

NASA Astrophysics Data System (ADS)

Jenkins, Adrian

2013-09-01

We describe how to define an extremely large discrete realization of a Gaussian white noise field that has a hierarchical structure and the property that the value of any part of the field can be computed quickly. Tiny subregions of such a field can be used to set the phase information for Gaussian initial conditions for individual cosmological simulations of structure formation. This approach has several attractive features: (i) the hierarchical structure based on an octree is particularly well suited for generating follow-up resimulation or zoom initial conditions; (ii) the phases are defined for all relevant physical scales in advance so that resimulation initial conditions are, by construction, consistent both with their parent simulation and with each other; (iii) the field can easily be made public by releasing a code to compute it - once public, phase information can be shared or published by specifying a spatial location within the realization. In this paper, we describe the principles behind creating such realizations. We define an example called Panphasia and in a companion paper by Jenkins and Booth (2013) make public a code to compute it. With 50 octree levels Panphasia spans a factor of more than 1015 in linear scale - a range that significantly exceeds the ratio of the current Hubble radius to the putative cold dark matter free-streaming scale. We show how to modify a code used for making cosmological and resimulation initial conditions so that it can take the phase information from Panphasia and, using this code, we demonstrate that it is possible to make good quality resimulation initial conditions. We define a convention for publishing phase information from Panphasia and publish the initial phases for several of the Virgo Consortium's most recent cosmological simulations including the 303 billion particle MXXL simulation. Finally, for reference, we give the locations and properties of several dark matter haloes that can be resimulated within these volumes.

INSTRUMENTS AND METHODS OF INVESTIGATION: Experimental investigation of the thermal properties of carbon at high temperatures and moderate pressures

NASA Astrophysics Data System (ADS)

Asinovskii, Erik I.; Kirillin, Alexander V.; Kostanovskii, Alexander V.

2002-08-01

A consistent procedure for plotting the carbon melting and boiling coexistence curves based on published data and the authors' experimental results is proposed. The parameters of a triple point are predicted to differ markedly from the currently accepted values: pt approx1 bar and Tt approx 4000 K. Two types of experimental facilities were used, with laser heating of samples in one and direct ohmic heating in the other. The existence of a carbyne region (a stable linear polymer consisting of carbon atoms) in the carbon phase diagram is discussed. Results on the direct solid-phase graphite - carbyne transition are presented, and this is shown to occur under certain conditions in the form of a thermal explosion.

Mathematical modelling of the human cardiovascular system in the presence of stenosis

NASA Technical Reports Server (NTRS)

Sud, V. K.; Srinivasan, R. S.; Charles, J. B.; Bungo, M. W.

1993-01-01

This paper reports a theoretical study on the distribution of blood flow in the human cardiovascular system when one or more blood vessels are affected by stenosis. The analysis employs a mathematical model of the entire system based on the finite element method. The arterial-venous network is represented by a large number of interconnected segments in the model. Values for the model parameters are based upon the published data on the physiological and rheological properties of blood. Computational results show how blood flow through various parts of the cardiovascular system is affected by stenosis in different blood vessels. No significant changes in the flow parameters of the cardiovascular system were found to occur when the reduction in the lumen diameter of the stenosed vessels was less than 65%.

36 CFR 1120.12 - Indexes to certain records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Indexes to certain records..., Documents Published and Indexed § 1120.12 Indexes to certain records. Current indexes are normally available to the public in published form as provided in § 1120.11. These indexes, whether or not published...

41 CFR 105-68.950 - Excluded Parties List System

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Excluded Parties List System 105-68.950 Section 105-68.950 Public Contracts and Property Management Federal Property Management... from Federal Procurement and Nonprocurement Programs,” so long as published. ...

Nerve ultrasound normal values - Readjustment of the ultrasound pattern sum score UPSS.

PubMed

Grimm, Alexander; Axer, Hubertus; Heiling, Bianka; Winter, Natalie

2018-07-01

Reference values are crucial for nerve ultrasound. Here, we reevaluated normal nerve and fascicle cross-sectional area (CSA) values in humans and compared them to published values. Based on these data, ultrasound pattern sum score (UPSS) boundary values were revisited and readjusted. Ultrasound of different peripheral nerves was performed in 100 healthy subjects at anatomically defined landmarks. Correlations with age, gender, height and weight were calculated. Overall, correspondence to other published reference values was high. Gender-dependency was found for the proximal median nerve. Dependency from height occurred in the tibial nerve (TN). Weight-dependency was not found. However, the most obvious differences were found in the TN between men >60 years and women <60 years. Thus, general boundary values were defined using the mean plus the twofold standard deviation for all subjects and nerve segments except for the TN, in which different cut-offs were proposed for elder men. Accordingly, the cut-offs for the UPSS were re-adjusted, none of the individuals revealed more than 2 points at maximum. The influence of distinct epidemiological factors on nerve size is most prominent in the TN, for which thus several normal values are useful. Adjusted reference values improve the accuracy of the UPSS. Copyright © 2018 International Federation of Clinical Neurophysiology. Published by Elsevier B.V. All rights reserved.

26 CFR 1.817-3 - Gain on property held on December 31, 1958, and certain substituted property acquired after 1958.

Code of Federal Regulations, 2010 CFR

2010-04-01

... REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Miscellaneous...) The fair market value of the property on December 31, 1958, exceeds the adjusted basis for determining... section 817(b)(1)) exceeds the difference between fair market value of such property on December 31, 1958...

26 CFR 25.2512-1 - Valuation of property; in general.

Code of Federal Regulations, 2010 CFR

2010-04-01

... AND GIFT TAXES GIFT TAX; GIFTS MADE AFTER DECEMBER 31, 1954 Transfers § 25.2512-1 Valuation of property; in general. Section 2512 provides that if a gift is made in property, its value at the date of the gift shall be considered the amount of the gift. The value of the property is the price at which...

41 CFR 102-73.40 - What happens if the dollar value of the project exceeds the prospectus threshold?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false What happens if the dollar value of the project exceeds the prospectus threshold? 102-73.40 Section 102-73.40 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 73-REAL ESTATE...

41 CFR 102-73.40 - What happens if the dollar value of the project exceeds the prospectus threshold?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false What happens if the dollar value of the project exceeds the prospectus threshold? 102-73.40 Section 102-73.40 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 73-REAL ESTATE...

An Analysis of Minnesota Property Values of Community Intermediate Care Facilities for Mentally Retarded (ICF-MRs). Issues Related to Welsch v. Noot. Policy Analysis Series No. 11.

ERIC Educational Resources Information Center

Minnesota Governor's Planning Council on Developmental Disabilities, St. Paul.

The paper analyzes one issue, property values, as an impact of Welsch v. Noot which affected zoning practices regarding group homes for mentally retarded persons. Assessed value was used to measure property vaues of 14 group home neighborhoods for the year preceding and following establishment of the home. Data were obtained from local tax…

[Measurement properties of self-report questionnaires published in Korean nursing journals].

PubMed

Lee, Eun-Hyun; Kim, Chun-Ja; Kim, Eun Jung; Chae, Hyun-Ju; Cho, Soo-Yeon

2013-02-01

The purpose of this study was to evaluate measurement properties of self-report questionnaires for studies published in Korean nursing journals. Of 424 Korean nursing articles initially identified, 168 articles met the inclusion criteria. The methodological quality of the measurements used in the studies and interpretability were assessed using the COnsensus-based Standards for the selection of health Measurement INstruments (COSMIN) checklist. It consists of items on internal consistency, reliability, measurement error, content validity, construct validity including structural validity, hypothesis testing, cross-cultural validity, and criterion validity, and responsiveness. For each item of the COSMIN checklist, measurement properties are rated on a four-point scale: excellent, good, fair, and poor. Each measurement property is scored with worst score counts. All articles used the classical test theory for measurement properties. Internal consistency (72.6%), construct validity (56.5%), and content validity (38.2%) were most frequently reported properties being rated as 'excellent' by COSMIN checklist, whereas other measurement properties were rarely reported. A systematic review of measurement properties including interpretability of most instruments warrants further research and nursing-focused checklists assessing measurement properties should be developed to facilitate intervention outcomes across Korean studies.

Strength/Brittleness Classification of Igneous Intact Rocks Based on Basic Physical and Dynamic Properties

NASA Astrophysics Data System (ADS)

Aligholi, Saeed; Lashkaripour, Gholam Reza; Ghafoori, Mohammad

2017-01-01

This paper sheds further light on the fundamental relationships between simple methods, rock strength, and brittleness of igneous rocks. In particular, the relationship between mechanical (point load strength index I s(50) and brittleness value S 20), basic physical (dry density and porosity), and dynamic properties (P-wave velocity and Schmidt rebound values) for a wide range of Iranian igneous rocks is investigated. First, 30 statistical models (including simple and multiple linear regression analyses) were built to identify the relationships between mechanical properties and simple methods. The results imply that rocks with different Schmidt hardness (SH) rebound values have different physicomechanical properties or relations. Second, using these results, it was proved that dry density, P-wave velocity, and SH rebound value provide a fine complement to mechanical properties classification of rock materials. Further, a detailed investigation was conducted on the relationships between mechanical and simple tests, which are established with limited ranges of P-wave velocity and dry density. The results show that strength values decrease with the SH rebound value. In addition, there is a systematic trend between dry density, P-wave velocity, rebound hardness, and brittleness value of the studied rocks, and rocks with medium hardness have a higher brittleness value. Finally, a strength classification chart and a brittleness classification table are presented, providing reliable and low-cost methods for the classification of igneous rocks.

Properties of crosslinked ultra-high-molecular-weight polyethylene.

PubMed

Lewis, G

2001-02-01

Substantially reducing the rate of generation of wear particles at the surfaces of ultra-high-molecular-weight polyethylene (UHMWPE) orthopedic implant bearing components, in vivo, is widely regarded as one of the most formidable challenges in modern arthroplasty. In the light of this, much research attention has been paid to the myriad of endogenous and exogenous factors that have been postulated to affect this wear rate, one such factor being the polymer itself. In recent years, there has been a resurgence of interest in crosslinking the polymer as a way of improving its properties that are considered relevant to its use for fabricating bearing components. Such properties include wear resistance, fatigue life, and fatigue crack propagation rate. Although a large volume of literature exists on the topic on the impact of crosslinking on the properties of UHMWPE, no critical appraisal of this literature has been published. This is one of the goals of the present article, which emphasizes three aspects. The first is the trade-off between improvement in wear resistance and depreciation in other mechanical and physical properties. The second aspect is the presentation of a method of estimating the optimal value of a crosslinking process variable (such as dose in radiation-induced crosslinking) that takes into account this trade-off. The third aspect is the description of a collection of under- and unexplored research areas in the field of crosslinked UHMWPE, such as the role of starting resin on the properties of the crosslinked polymer, and the in vitro evaluation of the wear rate of crosslinked tibial inserts and other bearing components that, in vivo, are subjected to nearly unidirectional motion.

Structural markers of the evolution of whey protein isolate powder during aging and effects on foaming properties.

PubMed

Norwood, E-A; Le Floch-Fouéré, C; Briard-Bion, V; Schuck, P; Croguennec, T; Jeantet, R

2016-07-01

The market for dairy powders, including high added-value products (e.g., infant formulas, protein isolates) has increased continuously over the past decade. However, the processing and storage of whey protein isolate (WPI) powders can result in changes in their structural and functional properties. It is therefore of great importance to understand the mechanisms and to identify the structural markers involved in the aging of WPI powders to control their end use properties. This study was performed to determine the effects of different storage conditions on protein lactosylations, protein denaturation in WPI, and in parallel on their foaming and interfacial properties. Six storage conditions involving different temperatures (θ) and water activities (aw) were studied for periods of up to 12mo. The results showed that for θ≤20°C, foaming properties of powders did not significantly differ from nonaged whey protein isolates (reference), regardless of the aw. On the other hand, powders presented significant levels of denaturation/aggregation and protein modification involving first protein lactosylation and then degradation of Maillard reaction products, resulting in a higher browning index compared with the reference, starting from the early stage of storage at 60°C. These changes resulted in a higher foam density and a slightly better foam stability (whisking) at 6mo. At 40°C, powders showed transitional evolution. The findings of this study will make it possible to define maximum storage durations and to recommend optimal storage conditions in accordance with WPI powder end-use properties. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Relationship between body mass, lean mass, fat mass, and limb bone cross-sectional geometry: Implications for estimating body mass and physique from the skeleton.

PubMed

Pomeroy, Emma; Macintosh, Alison; Wells, Jonathan C K; Cole, Tim J; Stock, Jay T

2018-05-01

Estimating body mass from skeletal dimensions is widely practiced, but methods for estimating its components (lean and fat mass) are poorly developed. The ability to estimate these characteristics would offer new insights into the evolution of body composition and its variation relative to past and present health. This study investigates the potential of long bone cross-sectional properties as predictors of body, lean, and fat mass. Humerus, femur and tibia midshaft cross-sectional properties were measured by peripheral quantitative computed tomography in sample of young adult women (n = 105) characterized by a range of activity levels. Body composition was estimated from bioimpedance analysis. Lean mass correlated most strongly with both upper and lower limb bone properties (r values up to 0.74), while fat mass showed weak correlations (r ≤ 0.29). Estimation equations generated from tibial midshaft properties indicated that lean mass could be estimated relatively reliably, with some improvement using logged data and including bone length in the models (minimum standard error of estimate = 8.9%). Body mass prediction was less reliable and fat mass only poorly predicted (standard errors of estimate ≥11.9% and >33%, respectively). Lean mass can be predicted more reliably than body mass from limb bone cross-sectional properties. The results highlight the potential for studying evolutionary trends in lean mass from skeletal remains, and have implications for understanding the relationship between bone morphology and body mass or composition. © 2018 The Authors. American Journal of Physical Anthropology Published by Wiley Periodicals, Inc.

Nanoscale reference materials for environmental, health and safety measurements: needs, gaps and opportunities.

PubMed

Stefaniak, Aleksandr B; Hackley, Vincent A; Roebben, Gert; Ehara, Kensei; Hankin, Steve; Postek, Michael T; Lynch, Iseult; Fu, Wei-En; Linsinger, Thomas P J; Thünemann, Andreas F

2013-12-01

The authors critically reviewed published lists of nano-objects and their physico-chemical properties deemed important for risk assessment and discussed metrological challenges associated with the development of nanoscale reference materials (RMs). Five lists were identified that contained 25 (classes of) nano-objects; only four (gold, silicon dioxide, silver, titanium dioxide) appeared on all lists. Twenty-three properties were identified for characterisation; only (specific) surface area appeared on all lists. The key themes that emerged from this review were: 1) various groups have prioritised nano-objects for development as "candidate RMs" with limited consensus; 2) a lack of harmonised terminology hinders accurate description of many nano-object properties; 3) many properties identified for characterisation are ill-defined or qualitative and hence are not metrologically traceable; 4) standardised protocols are critically needed for characterisation of nano-objects as delivered in relevant media and as administered to toxicological models; 5) the measurement processes being used to characterise a nano-object must be understood because instruments may measure a given sample in a different way; 6) appropriate RMs should be used for both accurate instrument calibration and for more general testing purposes (e.g., protocol validation); 7) there is a need to clarify that where RMs are not available, if "(representative) test materials" that lack reference or certified values may be useful for toxicology testing and 8) there is a need for consensus building within the nanotechnology and environmental, health and safety communities to prioritise RM needs and better define the required properties and (physical or chemical) forms of the candidate materials.

Metabolite diffusion up to very high b in the mouse brain in vivo: Revisiting the potential correlation between relaxation and diffusion properties

PubMed Central

Ligneul, Clémence; Palombo, Marco

2016-01-01

Purpose To assess the potential correlation between metabolites diffusion and relaxation in the mouse brain, which is of importance for interpreting and modeling metabolite diffusion based on pure geometry, irrespective of relaxation properties (multicompartmental relaxation or surface relaxivity). Methods A new diffusion‐weighted magnetic resonance spectroscopy sequence is introduced, dubbed “STE‐LASER,” which presents several nice properties, in particular the absence of cross‐terms with selection gradients and a very clean localization. Metabolite diffusion is then measured in a large voxel in the mouse brain at 11.7 Tesla using a cryoprobe, resulting in excellent signal‐to‐noise ratio, up to very high b‐values under different echo time, mixing time, and diffusion time combinations. Results Our results suggest that the correlation between relaxation and diffusion properties is extremely small or even nonexistent for metabolites in the mouse brain. Conclusion The present work strongly supports the interpretation and modeling of metabolite diffusion primarily based on geometry, irrespective of relaxation properties, at least under current experimental conditions. Magn Reson Med 77:1390–1398, 2017. © 2016 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution‐NonCommercial‐NoDerivs License, which permits use and distribution in any medium, provided the original work is properly cited, the use is non‐commercial and no modifications or adaptations are made. PMID:27018415

Geographic disparities in Healthy Eating Index scores (HEI-2005 and 2010) by residential property values: Findings from Seattle Obesity Study (SOS).

PubMed

Drewnowski, Adam; Aggarwal, Anju; Cook, Andrea; Stewart, Orion; Moudon, Anne Vernez

2016-02-01

Higher socioeconomic status (SES) has been linked with higher-quality diets. New GIS methods allow for geographic mapping of diet quality at a very granular level. To examine the geographic distribution of two measures of diet quality: Healthy Eating Index (HEI 2005 and HEI 2010) in relation to residential property values in Seattle-King County. The Seattle Obesity Study (SOS) collected data from a population-based sample of King County adults in 2008-09. Socio-demographic data were obtained by 20-min telephone survey. Dietary data were obtained from food frequency questionnaires (FFQs). Home addresses were geocoded to the tax parcel and residential property values were obtained from the King County tax assessor. Multivariable regression analyses using 1116 adults tested associations between SES variables and diet quality measured (HEI scores). Residential property values, education, and incomes were associated with higher HEI scores in bivariate analyses. Property values were not collinear with either education or income. In adjusted multivariable models, education and residential property were better associated with HEI, compared to than income. Mapping of HEI-2005 and HEI-2010 at the census block level illustrated the geographic distribution of diet quality across Seattle-King County. The use of residential property values, an objective measure of SES, allowed for the first visual exploration of diet quality at high spatial resolution: the census block level. Copyright © 2015 Elsevier Inc. All rights reserved.

Measurement of unsaturated hydraulic properties and evaluation of property-transfer models for deep sedimentary interbeds, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Perkins, Kimberlie; Johnson, Brittany D.; Mirus, Benjamin B.

2014-01-01

During 2013–14, the USGS, in cooperation with the U.S. Department of Energy, focused on further characterization of the sedimentary interbeds below the future site of the proposed Remote Handled Low-Level Waste (RHLLW) facility, which is intended for the long-term storage of low-level radioactive waste. Twelve core samples from the sedimentary interbeds from a borehole near the proposed facility were collected for laboratory analysis of hydraulic properties, which also allowed further testing of the property-transfer modeling approach. For each core sample, the steady-state centrifuge method was used to measure relations between matric potential, saturation, and conductivity. These laboratory measurements were compared to water-retention and unsaturated hydraulic conductivity parameters estimated using the established property-transfer models. For each core sample obtained, the agreement between measured and estimated hydraulic parameters was evaluated quantitatively using the Pearson correlation coefficient (r). The highest correlation is for saturated hydraulic conductivity (Ksat) with an r value of 0.922. The saturated water content (qsat) also exhibits a strong linear correlation with an r value of 0.892. The curve shape parameter (λ) has a value of 0.731, whereas the curve scaling parameter (yo) has the lowest r value of 0.528. The r values demonstrate that model predictions correspond well to the laboratory measured properties for most parameters, which supports the value of extending this approach for quantifying unsaturated hydraulic properties at various sites throughout INL.

Geographic disparities in Healthy Eating Index scores (HEI-2005 and 2010) by residential property values: Findings from Seattle Obesity Study (SOS)

PubMed Central

Drewnowski, Adam; Aggarwal, Anju; Cook, Andrea; Stewart, Orion; Vernez Moudon, Anne

2016-01-01

Background Higher socioeconomic status (SES) has been linked with higher-quality diets. New GIS methods allow for geographic mapping of diet quality at a very granular level. Objective To examine the geographic distribution of two measures of diet quality: Healthy Eating Index (HEI 2005 and HEI 2010) in relation to residential property values in Seattle-King County. Methods The Seattle Obesity Study (SOS) collected data from a population-based sample of King County adults in 2008–09. Socio-demographic data were obtained by 20-min telephone survey. Dietary data were obtained from food frequency questionnaires (FFQs). Home addresses were geocoded to the tax parcel and residential property values were obtained from the King County tax assessor. Multivariable regression analyses using 1,116 adults tested associations between SES variables and diet quality measured (HEI scores). Results Residential property values, education, and incomes were associated with higher HEI scores in bivariate analyses. Property values were not collinear with either education or income. In adjusted multivariable models, education and residential property were better associated with HEI, compared to than income. Mapping of HEI-2005 and HEI-2010 at the census block level illustrated the geographic distribution of diet quality across Seattle-King County. Conclusion The use of residential property values, an objective measure of SES, allowed for the first visual exploration of diet quality at high spatial resolution: the census block level. PMID:26657348

Mechanical Properties of 23 Species of Eastern Hardwoods.

Treesearch

B. A. Bendtsen; R. L. Ethington

1975-01-01

Important mechanical properties of clear, straight-grained wood of 23 species are tabulated, along with coefficients of variation. These property estimates can be used to match up species with kind of material needed for a specific job, or to search for substitutes for a presently used species. Some of the species appear, with allowable properties, in two published...

12 CFR 22.4 - Exemptions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... State-owned property covered under a policy of self-insurance satisfactory to the Director of FEMA, who publishes and periodically revises the list of States falling within this exemption; or (b) Property...

Do Affordable Housing Projects Harm Suburban Communities? Crime, Property Values, and Taxes in Mount Laurel, NJ.

PubMed

Albright, Len; Derickson, Elizabeth S; Massey, Douglas S

2013-06-01

This paper offers a mixed-method analysis of the municipal-level consequences of an affordable housing development built in suburban New Jersey. Opponents of affordable housing development often suggest that creating affordable housing will harm surrounding communities. Feared consequences include increases in crime, declining property values, and rising taxes. To evaluate these claims, the paper uses the case of Mt. Laurel, NJ - the site of a landmark affordable housing legal case and subsequent affordable housing development. Employing a multiple time series group control design, we compare crime rates, property values, and property taxes in Mt. Laurel to outcomes in similar nearby municipalities that do not contain comparable affordable housing developments. We find that the opening of the affordable housing development was not associated with trends in crime, property values, or taxes, and discuss management practices and design features that may have mitigated potential negative externalities.

Do Affordable Housing Projects Harm Suburban Communities? Crime, Property Values, and Taxes in Mount Laurel, NJ

PubMed Central

Albright, Len; Derickson, Elizabeth S.; Massey, Douglas S.

2016-01-01

This paper offers a mixed-method analysis of the municipal-level consequences of an affordable housing development built in suburban New Jersey. Opponents of affordable housing development often suggest that creating affordable housing will harm surrounding communities. Feared consequences include increases in crime, declining property values, and rising taxes. To evaluate these claims, the paper uses the case of Mt. Laurel, NJ – the site of a landmark affordable housing legal case and subsequent affordable housing development. Employing a multiple time series group control design, we compare crime rates, property values, and property taxes in Mt. Laurel to outcomes in similar nearby municipalities that do not contain comparable affordable housing developments. We find that the opening of the affordable housing development was not associated with trends in crime, property values, or taxes, and discuss management practices and design features that may have mitigated potential negative externalities. PMID:27390552

15 CFR 904.503 - Appraisement.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE GENERAL REGULATIONS CIVIL PROCEDURES Seizure... domestic value. Domestic value means the price at which such or similar property is offered for sale at the... property at the place of appraisement, the value in the principal market nearest the place of appraisement...

The distribution of P-values in medical research articles suggested selective reporting associated with statistical significance.

PubMed

Perneger, Thomas V; Combescure, Christophe

2017-07-01

Published P-values provide a window into the global enterprise of medical research. The aim of this study was to use the distribution of published P-values to estimate the relative frequencies of null and alternative hypotheses and to seek irregularities suggestive of publication bias. This cross-sectional study included P-values published in 120 medical research articles in 2016 (30 each from the BMJ, JAMA, Lancet, and New England Journal of Medicine). The observed distribution of P-values was compared with expected distributions under the null hypothesis (i.e., uniform between 0 and 1) and the alternative hypothesis (strictly decreasing from 0 to 1). P-values were categorized according to conventional levels of statistical significance and in one-percent intervals. Among 4,158 recorded P-values, 26.1% were highly significant (P < 0.001), 9.1% were moderately significant (P ≥ 0.001 to < 0.01), 11.7% were weakly significant (P ≥ 0.01 to < 0.05), and 53.2% were nonsignificant (P ≥ 0.05). We noted three irregularities: (1) high proportion of P-values <0.001, especially in observational studies, (2) excess of P-values equal to 1, and (3) about twice as many P-values less than 0.05 compared with those more than 0.05. The latter finding was seen in both randomized trials and observational studies, and in most types of analyses, excepting heterogeneity tests and interaction tests. Under plausible assumptions, we estimate that about half of the tested hypotheses were null and the other half were alternative. This analysis suggests that statistical tests published in medical journals are not a random sample of null and alternative hypotheses but that selective reporting is prevalent. In particular, significant results are about twice as likely to be reported as nonsignificant results. Copyright © 2017 Elsevier Inc. All rights reserved.

36 CFR 1212.220 - By when must I publish my drug-free workplace statement and establish my drug-free awareness...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false By when must I publish my... Individuals § 1212.220 By when must I publish my drug-free workplace statement and establish my drug-free... § 1212.205 and an ongoing awareness program as described in § 1212.215, you must publish the statement...

Rheological characteristics of cold thickened beverages containing xanthan gum-based food thickeners used for dysphagia diets.

PubMed

Cho, Hyun M; Yoo, Byoungseung

2015-01-01

Cold beverages are commonly thickened with commercial gum-based food thickeners for consumption by patients with dysphagia. In this study, the rheological properties of a thickened water and five thickened beverages (orange juice, apple juice, grape juice, whole milk, and a sport drink) that were prepared with four commercial instant xanthan gum-based thickeners (coded A-D) were investigated at a 3% thickener concentration. All thickened samples showed high shear-thinning behavior with yield stress at the serving temperature of 8°C. The magnitudes of apparent viscosity (ηa,50), consistency index (K), storage modulus (G'), and loss modulus (G'') of the thickened beverages, except for water, with food thickener A were significantly higher compared with other thickeners (B, C, and D) (P<0.05). The largest increases in K values for thickened beverages were observed at 1-hour storage, and at longer times their K values, except for milk, remained approximately constant. Rheological parameters demonstrated statistically significant differences in flow and dynamic behaviors between the cold thickened beverages prepared with the xanthan gum-based food thickeners (P<0.05), indicating that their rheological properties are strongly influenced by the dispersing medium, the type of food thickener, and storage time. In particular, appropriately selecting a commercial food thickener for preparing thickened beverages seems to be of importance for managing dysphagia. Copyright © 2015 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Functionalized gold nanoparticles for the detection of arsenic in water.

PubMed

Domínguez-González, R; González Varela, L; Bermejo-Barrera, P

2014-01-01

Gold nanoparticles are attractive as sensing materials because of their size and shape are related with their optical properties. The color change produced by the aggregation of functionalized AuNPs allows the detection of arsenic at low levels. A simple, cheap and fast analytical procedure to perform arsenic determination using functionalized gold nanoparticles (AuNPs) and VIS spectrometry as a detection technique is studied. Three different synthesis procedures to obtain the AuNPs and two different functionalization modes were studied. AuNPs functionalized with GSH-DTT-CYs-PDCA were selected as the most adequate. The correlation between the decrease in the absorbance signal and the arsenic concentration was good in the 2-20 µg l(-1)interval. Repeatability, expressed as average of RSD (%), obtained for the different arsenic concentrations studied was 0.6%. The average value of the analytical recovery was 99.7%. The detection and quantifications limits were 2.5 and 8.4 µg l(-1) respectively. These limits are sufficient to detect World Health Organization's guideline value of 10 µg l(-1). © 2013 Published by Elsevier B.V.

Characterisation of a thiamine diphosphate-dependent alpha-keto acid decarboxylase from Proteus mirabilis JN458.

PubMed

Wang, Biying; Bai, Yajun; Fan, Taiping; Zheng, Xiaohui; Cai, Yujie

2017-10-01

Alpha-keto acid decarboxylases can convert keto acids to their corresponding aldehydes, which are often volatile aroma compounds. The gene encoding α-keto acid decarboxylase in Proteus mirabilis JN458 was cloned, and the enzyme overexpressed in Escherichia coli BL21 (DE3), purified in high yield, and characterised. The molecular weight is 62.291kDa by MALDI-TOF MS, and optimum activity at pH 6.0 and 40-50°C. The enzyme is a typical decarboxylase, dependent on thiamine diphosphate and Mg 2+ as cofactors. For the decarboxylation reaction, the enzyme displayed a broad substrate range. Kinetic parameters were determined using 4-methyl-2-oxopentanoic acid, phenyl pyruvate and 3-methyl-2-oxopentanoic acid as substrates. K m and k cat values for phenyl pyruvate were 0.62mM and 77.38s -1 , respectively, and the k cat /K m value was 124.81mM -1 s -1 . The enzyme properties suggest it may act effectively under cheese ripening conditions. Copyright © 2017. Published by Elsevier Ltd.

Atrial Cardiomyopathy: A Useful Notion in Cardiac Disease Management or a Passing Fad?

PubMed

Guichard, Jean-Baptiste; Nattel, Stanley

2017-08-08

The term atrial cardiomyopathy, which has been used sporadically in the medical literature, was recently the subject of a detailed Consensus Document prepared by representatives of the European Heart Rhythm Association, Heart Rhythm Society, Asia-Pacific Heart Rhythm Society, and Sociedad Latinoamericana de Estimulación Cardiaca y Electrofisiología. They discussed aspects of the definition, histopathology, atrial-specific physiology, atrial pathology, impact on arrhythmia occurrence, imaging, mapping, and ablation. Here, the authors consider critically the added clinical value of this concept and its meaningfulness. They review evidence implicating atrial cardiomyopathy as an independent contributor to the risk of stroke associated with atrial fibrillation and as a determinant of arrhythmia progression. The issue of classification is considered and the authors discuss how atrial cardiomyopathic properties might guide stroke prevention, rhythm maintenance, and rate control in atrial fibrillation. Carefully designed clinical trials are needed to evaluate these potential applications, and will ultimately define the value of this terminology. Copyright © 2017 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

Anabolic androgenic steroids reverse the beneficial effect of exercise on tendon biomechanics: an experimental study.

PubMed

Tsitsilonis, Serafim; Chatzistergos, Panayiotis E; Panayiotis, Chatzistergos E; Mitousoudis, Athanasios S; Athanasios, Mitousoudis S; Kourkoulis, Stavros K; Stavros, Kourkoulis K; Vlachos, Ioannis S; Ioannis, Vlachos S; Agrogiannis, George; George, Agrogiannis; Fasseas, Konstantinos; Konstantinos, Fasseas; Perrea, Despina N; Despina, Perrea N; Zoubos, Aristides B; Aristides, Zoubos B

2014-06-01

The effect of anabolic androgenic steroids on tendons has not yet been fully elucidated. Aim of the present study was the evaluation of the impact of anabolic androgenic steroids on the biomechanical and histological characteristics of Achilles tendons. Twenty-four male Wistar rats were randomized into four groups with exercise and anabolic steroids (nandrolone decanoate) serving as variables. Protocol duration was 12 weeks. Following euthanasia, tendons' biomechanical properties were tested with the use of a modified clamping configuration. Histological examination with light and electron microscopy were also performed. In the group of anabolic steroids and exercise the lowest fracture stress values were observed, while in the exercise group the highest ones. Histological examination by light and electron microscopy revealed areas of collagen dysplasia and an increased epitendon in the groups receiving anabolic steroids and exercise. These findings suggest that anabolic androgenic steroids reverse the beneficial effect of exercise, thus resulting in inferior maximal stress values. Copyright © 2013 European Foot and Ankle Society. Published by Elsevier Ltd. All rights reserved.

Physical and chemical characteristics of products from the torrefaction of yellow poplar (Liriodendron tulipifera).

PubMed

Kim, Young-Hun; Lee, Soo-Min; Lee, Hyoung-Woo; Lee, Jae-Won

2012-07-01

We investigated the characteristics of torrefied yellow poplar (Liriodendron tulipifera) depending on reaction time (30 min) and temperature (240-280 °C). The thermogravimetric, grindability and calorific value of torrefied biomass were analyzed. As the torrefaction temperature increased, the carbon content of torrefied biomass increased from 49.50% to 54.42%, while the hydrogen and oxygen contents decreased from 6.09% to 5.65% and 28.71% to 26.61%, respectively. The highest calorific value was 1233 kJ/kg when torrefaction was performed at 280 °C for 30 min. An overall increase in energy density and decrease in mass and energy yield was observed with the increase in torrefaction temperature. The analysis of thermal decomposition demonstrated that the hemicelluloses contained in torrefied biomass decreased with increasing torrefaction temperature, whereas cellulose and lignin were only slightly affected. The grindability of torrefied biomass was significantly improved when torrefaction was performed at high temperature. Torrefaction of yellow poplar improved the chemical and physical fuel properties of the biomass. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Phytochemical investigations and antioxidant potential of roots of Leea macrophylla (Roxb.).

PubMed

Mahmud, Zobaer Al; Bachar, Sitesh C; Hasan, Choudhury Mahmood; Emran, Talha Bin; Qais, Nazmul; Uddin, Mir Muhammad Nasir

2017-07-06

Oleanolic acid (NZ-15), 7 α, 28-olean diol (NZ-38) and Stigmasterol (NZ-14) were isolated from the ethanolic extracts of the roots of Leea macrophylla (Family: Leeaceae) by using chromatographic analysis. This is the first report of isolation of these compounds from this plant. Their structures were constructed by spectroscopic analysis and by comparing the data with the published one. Subsequently the ethanolic extract was fractionated with two organic solvents and all the fractions were studied to evaluate their in vitro antioxidant property. The ethanolic extract was fractionated with two organic solvents and all the fractions were studied to evaluate their in vitro antioxidant property by DPPH free radical scavenging assay, superoxide anion radical scavenging assay, nitric oxide radical scavenging assay, and reducing power assay. In the DPPH free radical scavenging assay and superoxide radical scavenging assay, the ethyl acetate soluble fraction of ethanolic extract revealed the highest free radical scavenging activity with IC 50 value of 2.65 and 155.62 μg/ml, respectively as compared to standard ascorbic acid (IC 50 value of 5.8 and 99.66 μg/ml). Ethyl acetate fraction also possessed highest reducing power activity with an EC50 value of 15.27 μg/ml compared to ascorbic acid (EC 50 0.91 μg/ml). On the other hand, the carbon tetrachloride fraction exhibited most significant NO scavenging activity with IC 50 value of 277.8 μg/ml that was even higher than that of standard ascorbic acid (IC 50 value 356.04 μg/ml). In addition, the total phenolic contents of these extract and fractions were evaluated using Folin-Ciocalteu reagent and varied from 7.93 to 50.21 mg/g dry weight expressed as gallic acid equivalents (GAE). This study showed that different extracts of roots of L. macrophylla possess potential DPPH, superoxide, and NO free radical scavenging activities. The antioxidant activities of the plant extracts might be due to the presence of oleanolic acid, oleanolic acid derivative 7 α, 28-olean diol and stigmasterol.

Legislation.

ERIC Educational Resources Information Center

Henderson, Carol C.; Heanue, Anne A.; Adler, Allan R.

1998-01-01

Two reports discuss legislation and regulations affecting libraries in 1997, (funding, government information, intellectual freedom and property, Next Generation Internet, postal rates, telecommunications) and publishing in 1997 (intellectual property, freedom of expression, new technology, postal rates). (PEN)

The value of urban tree cover: A hedonic property price model in Ramsey and Dakota Counties, Minnesota, USA

Treesearch

Heather Sander; Stephen Polasky; Robert. Haight

2010-01-01

Urban tree cover benefits communities. These benefits' economic values, however, are poorly recognized and often ignored by landowners and planners. We use hedonic property price modeling to estimate urban tree cover's value in Dakota and Ramsey Counties, MN, USA, predicting housing value as a function of structural, neighborhood, and environmental variables...

44 CFR 209.8 - Application and review process.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., the applicant should add the relevant adjustment percentage for that jurisdiction to adjust the tax...-event fair market value of the home. Applicants will estimate the value of properties using the best available information, such as inspections, public records and market values of similar properties in...

44 CFR 209.8 - Application and review process.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., the applicant should add the relevant adjustment percentage for that jurisdiction to adjust the tax...-event fair market value of the home. Applicants will estimate the value of properties using the best available information, such as inspections, public records and market values of similar properties in...

44 CFR 209.8 - Application and review process.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., the applicant should add the relevant adjustment percentage for that jurisdiction to adjust the tax...-event fair market value of the home. Applicants will estimate the value of properties using the best available information, such as inspections, public records and market values of similar properties in...

44 CFR 209.8 - Application and review process.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., the applicant should add the relevant adjustment percentage for that jurisdiction to adjust the tax...-event fair market value of the home. Applicants will estimate the value of properties using the best available information, such as inspections, public records and market values of similar properties in...

Association of Malignancy Prevalence With Test Properties and Performance of the Gene Expression Classifier in Indeterminate Thyroid Nodules.

PubMed

Al-Qurayshi, Zaid; Deniwar, Ahmed; Thethi, Tina; Mallik, Tilak; Srivastav, Sudesh; Murad, Fadi; Bhatia, Parisha; Moroz, Krzysztof; Sholl, Andrew B; Kandil, Emad

2017-04-01

It is crucial for clinicians to know the malignancy prevalence within each indeterminate cytologic category to estimate the performance of the gene expression classifier (GEC). To examine the variability in the performance of the GEC. This retrospective cohort study of patients with Bethesda category III and IV thyroid nodules used single-institution data from January 1, 2013, through February 29, 2016. Expected negative predictive value (NPV) was calculated by adopting published sensitivity and specificity. Observed NPV was calculated based on the true-negative rate. Outcomes were compared with pooled data from 11 studies published January 1, 2010, to January 31, 2016. A total of 145 patients with 154 thyroid nodules were included in the study (mean [SD] age, 56.0 [16.2] years; 106 females [73.1%]). Malignancy prevalence was 45%. On the basis of this prevalence, the expected NPV is 85% and the observed NPV is 69%. If the prevalence is assumed to be 25%, the expected NPV would be 94%, whereas the observed NPV would be 85%. Pooled data analysis of 11 studies comprising 1303 participants revealed a malignancy prevalence of 31% (95% CI, 29%-34%) and a pooled NPV of 92% (95% CI, 87%-96%). In this study, variability in the performance of the GEC was not solely a function of malignancy prevalence and may have been attributable to intrinsic variability of the test sensitivity and specificity. The utility of the GEC in practice is elusive because of this variability. A better definition of the GEC's intrinsic properties is needed.

32 CFR 644.353 - Determination of values for reporting.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 4 2011-07-01 2011-07-01 false Determination of values for reporting. 644.353 Section 644.353 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Reports of Excess Real Property and Related Personal Property to...

32 CFR 644.353 - Determination of values for reporting.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 4 2013-07-01 2013-07-01 false Determination of values for reporting. 644.353 Section 644.353 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Reports of Excess Real Property and Related Personal Property to...

32 CFR 644.353 - Determination of values for reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Determination of values for reporting. 644.353 Section 644.353 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Reports of Excess Real Property and Related Personal Property to...

32 CFR 644.353 - Determination of values for reporting.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 4 2014-07-01 2013-07-01 true Determination of values for reporting. 644.353 Section 644.353 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Reports of Excess Real Property and Related Personal Property to...

32 CFR 644.353 - Determination of values for reporting.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 4 2012-07-01 2011-07-01 true Determination of values for reporting. 644.353 Section 644.353 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Reports of Excess Real Property and Related Personal Property to...

Timber management and use-value assessment

Treesearch

Paul E. Sendak; Neil K. Huyler

1994-01-01

Describes timber management activity and estimates timber harvest from forest land enrolled in Vermont's Use Value Appraisal (UVA) Forest Land property tax program. Data were compiled from the mandatory management plans and annual conformance reports filed for each property enrolled in the Program. Overall, 31 percent of the UVA properties reported a commercial...

77 FR 7231 - Public Notice for Release of Aeronautical Property at New Castle Airport (ILG), New Castle, DE

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-10

... exchanged. The fee simple property value of the 2.424 +/- acre area is estimated at $55,000.00+/- per acre... the fee simple fair market value of the property, no monetary payment for the easement would be required. Interested persons are invited to comment on the proposed change in use of the property. All...

The Precise Measurement of Vapor-Liquid Equilibrium Properties of the CO2/Isopentane Binary Mixture, and Fitted Parameters for a Helmholtz Energy Mixture Model

NASA Astrophysics Data System (ADS)

Miyamoto, H.; Shoji, Y.; Akasaka, R.; Lemmon, E. W.

2017-10-01

Natural working fluid mixtures, including combinations of CO2, hydrocarbons, water, and ammonia, are expected to have applications in energy conversion processes such as heat pumps and organic Rankine cycles. However, the available literature data, much of which were published between 1975 and 1992, do not incorporate the recommendations of the Guide to the Expression of Uncertainty in Measurement. Therefore, new and more reliable thermodynamic property measurements obtained with state-of-the-art technology are required. The goal of the present study was to obtain accurate vapor-liquid equilibrium (VLE) properties for complex mixtures based on two different gases with significant variations in their boiling points. Precise VLE data were measured with a recirculation-type apparatus with a 380 cm3 equilibration cell and two windows allowing observation of the phase behavior. This cell was equipped with recirculating and expansion loops that were immersed in temperature-controlled liquid and air baths, respectively. Following equilibration, the composition of the sample in each loop was ascertained by gas chromatography. VLE data were acquired for CO2/ethanol and CO2/isopentane binary mixtures within the temperature range from 300 K to 330 K and at pressures up to 7 MPa. These data were used to fit interaction parameters in a Helmholtz energy mixture model. Comparisons were made with the available literature data and values calculated by thermodynamic property models.

Preparation, anti-biofouling and drag-reduction properties of a biomimetic shark skin surface.

PubMed

Pu, Xia; Li, Guangji; Huang, Hanlu

2016-04-15

Shark skin surfaces show non-smoothness characteristics due to the presence of a riblet structure. In this study, biomimetic shark skin was prepared by using the polydimethylsiloxane (PDMS)-embedded elastomeric stamping (PEES) method. Scanning electron microscopy (SEM) was used to examine the surface microstructure and fine structure of shark skin and biomimetic shark skin. To analyse the hydrophobic mechanism of the shark skin surface microstructure, the effect of biomimetic shark skin surface microstructure on surface wettability was evaluated by recording water contact angle. Additionally, protein adhesion experiments and anti-algae adhesion performance testing experiments were used to investigate and evaluate the anti-biofouling properties of the surface microstructure of biomimetic shark skin. The recorded values of the water contact angle of differently microstructured surfaces revealed that specific microstructures have certain effects on surface wettability. The anti-biofouling properties of the biomimetic shark skin surface with microstructures were superior to a smooth surface using the same polymers as substrates. Moreover, the air layer fixed on the surface of the biomimetic shark skin was found to play a key role in their antibiont adhesion property. An experiment into drag reduction was also conducted. Based on the experimental results, the microstructured surface of the prepared biomimetic shark skin played a significant role in reducing drag. The maximum of drag reduction rate is 12.5%, which is higher than the corresponding maximum drag reduction rate of membrane material with a smooth surface. © 2016. Published by The Company of Biologists Ltd.

Calcium silicate-based sealers: Assessment of physicochemical properties, porosity and hydration.

PubMed

Marciano, Marina Angélica; Duarte, Marco Antonio Hungaro; Camilleri, Josette

2016-02-01

Investigation of hydration, chemical, physical properties and porosity of experimental calcium silicate-based sealers. Experimental calcium silicate-based sealers with calcium tungstate and zirconium oxide radio-opacifiers were prepared by mixing 1g of powder to 0.3 mL of 80% distilled water and 20% propylene glycol. MTA and MTA Fillapex were used as controls. The raw materials and set sealers were characterized using a combination of scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction. Physical properties were analyzed according to ANSI/ADA. The pH and calcium ion release were assessed after 3, 24, 72 and 168 h. The porosity was assessed using mercury intrusion porosimetry. The analysis of hydration of prototype sealers revealed calcium hydroxide as a by-product resulting in alkaline pH and detection of calcium ion release, with high values in initial periods. The radiopacity was similar to MTA for the sealers containing high amounts of radio-opacifiers (p>0.05). Flowability was higher and film thickness was lower for resinous MTA Fillapex sealer (p<0.05). The test sealers showed water sorption and porosity similar to MTA (p>0.05). The prototype sealers presented adequate hydration, elevated pH and calcium ion release. Regarding physical properties, elevated proportions of radio-opacifiers were necessary to accomplish adequate radiopacity, enhance flowability and reduce film thickness. All the tested sealers presented water sorption and porosity similar to MTA. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Ultrasound bladder wall thickness measurement in diagnosis of recurrent urinary tract infections and cystitis cystica in prepubertal girls.

PubMed

Milošević, Danko; Trkulja, Vladimir; Turudić, Daniel; Batinić, Danica; Spajić, Borislav; Tešović, Goran

2013-12-01

To evaluate urinary bladder wall thickness (BWT) assessed by ultrasound as a diagnostic tool for cystitis cystica. This was a 9-year prospective study comprising 120 prepubertal girls. Sixty subjects of whom half underwent cystoscopy represented cases while the other 60 (those with a single urinary tract infection and healthy subjects) represented controls. Based on receiver operating characteristics (ROC) analysis, BWT discriminated very well between cases and controls with area under the ROC curve close to 1.0. At the optimum cut-off defined at 3.9 mm, negative predictive value (NPV) was 100% leaving no probability of cystic cystitis with BWT <3.9 mm. Positive predictive value (PPV) was also very high (95.2%), indicating only around 4.82% probability of no cystic cystitis in patients with BWT values ≥3.9 mm. BWT could also distinguish between healthy subjects and those with a cured single urinary tract infection, although discriminatory properties were moderate (area under ROC 86.7%, PPV 78.8%, NPV 85.2%). Ultrasound mucosal bladder wall measurement is a non-invasive, simple and quite reliable method in diagnosis of cystitis cystica in prepubertal girls with recurrent urinary tract infections. Copyright © 2013 Journal of Pediatric Urology Company. Published by Elsevier Ltd. All rights reserved.

Short communication: Serum composition of milk subjected to re-equilibration by dialysis at different temperatures, after pH adjustments.

PubMed

Zhao, Zhengtao; Corredig, Milena

2016-04-01

The objective of this work was to investigate the properties of casein micelles after pH adjustment and their re-equilibration to the original pH and serum composition. Re-equilibration was carried out by dialyzing against skim milk at 2 different temperatures (4 or 22 °C). Turbidity, the average radius of the casein micelles, and the composition of the soluble phase were measured at different pH values, ranging between 5.5 and 8. Acidification led to the solubilization of colloidal calcium phosphate and decrease of the average radius of the micelles. With re-equilibration, casein dissociation occurred. In milk with pH values greater than 6.0, the average radius was recovered after re-equilibration. At pH values greater than neutral, an increase of the radius of casein micelles and increased dissociation of the casein were found. After re-equilibration, the radius of micelles and soluble protein in the serum decreased. The results were not affected by the temperature of re-equilibration. The changes to the calcium phosphate equilibrium and the dissociation of the micelles will have important consequences to the functionality of casein micelles. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The refined physical properties of transiting exoplanetary system WASP-11/HAT-P-10

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xiao-bin; Gu, Sheng-hong; Wang, Yi-bo

2014-04-01

The transiting exoplanetary system WASP-11/HAT-P-10 was observed using the CCD camera at Yunnan Observatories, China from 2008 to 2011, and four new transit light curves were obtained. Combined with published radial velocity measurements, the new transit light curves are analyzed along with available photometric data from the literature using the Markov Chain Monte Carlo technique, and the refined physical parameters of the system are derived, which are compatible with the results of two discovery groups, respectively. The planet mass is M{sub p} = 0.526 ± 0.019 M{sub J} , which is the same as West et al.'s value, and moremore » accurately, the planet radius R{sub p} = 0.999{sub −0.018}{sup +0.029} R{sub J} is identical to the value of Bakos et al. The new result confirms that the planet orbit is circular. By collecting 19 available mid-transit epochs with higher precision, we make an orbital period analysis for WASP-11b/HAT-P-10b, and derive a new value for its orbital period, P = 3.72247669 days. Through an (O – C) study based on these mid-transit epochs, no obvious transit timing variation signal can be found for this system during 2008-2012.« less

Economic evaluation of smoke alarm distribution methods in Baltimore, Maryland.

PubMed

Diamond-Smith, Nadia; Bishai, David; Perry, Elise; Shields, Wendy; Gielen, Andrea

2014-08-01

This paper analyses costs and potential lives saved from a door-to-door smoke alarm distribution programme using data from a programme run by the Baltimore City Fire Department in 2010-2011. We evaluate the impact of a standard home visit programme and an enhanced home visit programme that includes having community health workers provide advance notice, promote the programme, and accompany fire department personnel on the day of the home visit, compared with each other and with an option of not having a home visit programme (control). Study data show that the home visit programme increased by 10% the number of homes that went from having no working alarm to having any working alarm, and the enhanced programme added an additional 1% to the number of homes protected. We use published reports on the relative risk of death in homes with and without a working smoke alarm to show that the standard programme would save an additional 0.24 lives per 10,000 homes over 10 years, compared with control areas and the enhanced home visit programme saved an additional 0.07 lives compared with the standard programme. The incremental cost of each life saved for the standard programme compared with control was $28,252 per death averted and $284,501per additional death averted for the enhanced compared with the standard. Following the US guidelines for the value of a life, both programmes are cost effective, however, the standard programme may offer a better value in terms of dollars per death averted. The study also highlights the need for better data on the benefits of current smoke alarm recommendations and their impact on injury, death and property damage. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Experimental validation of new empirical models of the thermal properties of food products for safe shipping

NASA Astrophysics Data System (ADS)

Hamid, Hanan H.; Mitchell, Mark; Jahangiri, Amirreza; Thiel, David V.

2018-04-01

Temperature controlled food transport is essential for human safety and to minimise food waste. The thermal properties of food are important for determining the heat transfer during the transient stages of transportation (door opening during loading and unloading processes). For example, the temperature of most dairy products must be confined to a very narrow range (3-7 °C). If a predefined critical temperature is exceeded, the food is defined as spoiled and unfit for human consumption. An improved empirical model for the thermal conductivity and specific heat capacity of a wide range of food products was derived based on the food composition (moisture, fat, protein, carbohydrate and ash). The models that developed using linear regression analysis were compared with the published measured parameters in addition to previously published theoretical and empirical models. It was found that the maximum variation in the predicated thermal properties leads to less than 0.3 °C temperature change. The correlation coefficient for these models was 0.96. The t-Stat test ( P-value >0.99) demonstrated that the model results are an improvement on previous works. The transient heat transfer based on the food composition and the temperature boundary conditions was found for a Camembert cheese (short cylindrical shape) using a multiple dimension finite difference method code. The result was verified using the heat transfer today (HTT) educational software which is based on finite volume method. The core temperature rises from the initial temperature (2.7 °C) to the maximum safe temperature in ambient air (20.24 °C) was predicted to within about 35.4 ± 0.5 min. The simulation results agree very well ( +0.2 °C) with the measured temperature data. This improved model impacts on temperature estimation during loading and unloading the trucks and provides a clear direction for temperature control in all refrigerated transport applications.

Impact of gastric acidic challenge on surface topography and optical properties of monolithic zirconia.

PubMed

Sulaiman, Taiseer A; Abdulmajeed, Aous A; Shahramian, Khalil; Hupa, Leena; Donovan, Terrence E; Vallittu, Pekka; Närhi, Timo O

2015-12-01

To evaluate the surface topography and optical properties of monolithic zirconia after immersion in simulated gastric acid. Four partially stabilized (PSZ) and one fully stabilized (FSZ) zirconia materials were selected for the study: Prettau (PRT, Zirkonzahn), Zenostar (ZEN, Ivoclar), Bruxzir (BRX, Glidewell), Katana (KAT, Noritake) and FSZ Prettau Anterior (PRTA, Zirkonzahn). IPS e.max (Ivoclar) was used as a control. The specimens (10×10×1.2mm, n=5 per material) were cut, sintered, polished and cleaned before immersed in 5ml of simulated gastric acid solution (Hydrochloric acid (HCl) 0.06M, 0.113% solution in deionized distal water, pH 1.2) for 96h in a 37°C incubator. Specimens were weighed and examined for morphological changes under scanning electron microscope (SEM) coupled with energy dispersive X-ray spectroscopy (EDX). Surface roughness was evaluated by a confocal microscope. Surface gloss and translucency parameter (TP) values were determined by a reflection spectrophotometer before and after acid immersion. The data was analyzed by one-way ANOVA followed by Tukey's HSD post hoc test (p<0.05). PRTA displayed the most weight loss (1.40%) among the zirconia specimens. IPS e.max showed about three times more weight loss (3.05%) than zirconia specimens as an average. SEM examination indicated areas of degradation, bead-like shapes and smoothening of the polishing scratches after acid immersion. EDX displayed ion interactions and possible ion leaching from all specimens. Sa and Sq values for PRTA, ZEN and IPS e.max were significantly lower (p<0.05) after acid immersion. TP values increased significantly for PRT, ZEN and IPS e.max (p<0.05), while the surface gloss of ZEN, PRTA and IPS e.max increased (p<0.05). Monolithic zirconia materials show some surface alterations in an acidic environment with minimum effect on their optical properties. Whether a smoother surface is in fact a sign of true corrosion resistance or is purely the result of an evenly progressive corrosive process is yet to be confirmed by further research. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Stabilization of arsenic and fluoride bearing spent adsorbent in clay bricks: Preparation, characterization and leaching studies.

PubMed

Rathore, Vineet Kumar; Mondal, Prasenjit

2017-09-15

The presence of arsenic and fluoride in groundwater has been observed throughout the world. Many technologies have been developed by various research groups in order to tackle this problem. Adsorption has emerged as one of the best possible technique for the removal of arsenic, fluoride and many other pollutants from drinking water. Although a considerable amount of work has been published on the adsorptive removal of arsenic and fluoride, the area related to the management of spent adsorbent is not well explored. Present paper deals with the adsorptive removal of arsenic and fluoride from aqueous solution by three different types of adsorbents, namely, thermally treated laterite (TTL), acid-base treated laterite (ABTL) and aluminum oxide/hydroxide nanoparticles (AHNP). Under the experimental conditions in batch operation, the adsorption capacities of TTL, ABLT and AHNP for arsenic are found to be 6.43 μg/g, 9.25 μg/g and 48.5 μg/g respectively, whereas for fluoride, these values are found as 0.21 mg/g, 0.85 mg/g and 4.65 mg/g respectively. After adsorption, the spent adsorbents have been stabilized in the form of clay bricks. The effects of spent adsorbent concentration on the properties of bricks and their leaching properties are investigated. The bricks have been tested for various properties like density, percentage water absorption, shrinkage, compressive strength and efflorescence. The maximum values of density and shrinkage of the bricks formed are found as 2.3 g/cm 3 and 10.2%, whereas the percentage water absorption and compressive strength of the bricks are found between 11 and 14% and 35 to 150 kgf/cm 2 respectively. All the test results are in accordance with the criteria set by Indian Standards. The leaching test of arsenic and fluoride from the bricks reveals that their maximum values in leachate are 510 μg/L and 2.1 mg/L respectively, which are below the permissible limits of USEPA standards. Copyright © 2017 Elsevier Ltd. All rights reserved.

41 CFR 105-53.100 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Purpose. 105-53.100 Section 105-53.100 Public Contracts and Property Management Federal Property Management Regulations System.... This part is published in accordance with 5 U.S.C. 552 and is a general description of the General...

41 CFR 101-1.104-1 - Publication.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 41 Public Contracts and Property Management 2 2014-07-01 2012-07-01 true Publication. 101-1.104-1 Section 101-1.104-1 Public Contracts and Property Management Federal Property Management Regulations... Publication. FPMR will be published in the Federal Register, in looseleaf form, and in accumulated form in the...

41 CFR 101-1.104-1 - Publication.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 41 Public Contracts and Property Management 2 2011-07-01 2007-07-01 true Publication. 101-1.104-1 Section 101-1.104-1 Public Contracts and Property Management Federal Property Management Regulations... Publication. FPMR will be published in the Federal Register, in looseleaf form, and in accumulated form in the...

41 CFR 101-1.104-1 - Publication.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 41 Public Contracts and Property Management 2 2012-07-01 2012-07-01 false Publication. 101-1.104-1 Section 101-1.104-1 Public Contracts and Property Management Federal Property Management Regulations... Publication. FPMR will be published in the Federal Register, in looseleaf form, and in accumulated form in the...

41 CFR 101-1.104-1 - Publication.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 2 2013-07-01 2012-07-01 true Publication. 101-1.104-1 Section 101-1.104-1 Public Contracts and Property Management Federal Property Management Regulations... Publication. FPMR will be published in the Federal Register, in looseleaf form, and in accumulated form in the...

Temporal development of near-native functional properties and correlations with qMRI in self-assembling fibrocartilage treated with exogenous lysyl oxidase homolog 2.

PubMed

Hadidi, Pasha; Cissell, Derek D; Hu, Jerry C; Athanasiou, Kyriacos A

2017-12-01

Advances in cartilage tissue engineering have led to constructs with mechanical integrity and biochemical composition increasingly resembling that of native tissues. In particular, collagen cross-linking with lysyl oxidase has been used to significantly enhance the mechanical properties of engineered neotissues. In this study, development of collagen cross-links over time, and correlations with tensile properties, were examined in self-assembling neotissues. Additionally, quantitative MRI metrics were examined in relation to construct mechanical properties as well as pyridinoline cross-link content and other engineered tissue components. Scaffold-free meniscus fibrocartilage was cultured in the presence of exogenous lysyl oxidase, and assessed at multiple time points over 8weeks starting from the first week of culture. Engineered constructs demonstrated a 9.9-fold increase in pyridinoline content, reaching 77% of native tissue values, after 8weeks of culture. Additionally, engineered tissues reached 66% of the Young's modulus in the radial direction of native tissues. Further, collagen cross-links were found to correlate with tensile properties, contributing 67% of the tensile strength of engineered neocartilages. Finally, examination of quantitative MRI metrics revealed several correlations with mechanical and biochemical properties of engineered constructs. This study displays the importance of culture duration for collagen cross-link formation, and demonstrates the potential of quantitative MRI in investigating properties of engineered cartilages. This is the first study to demonstrate near-native cross-link content in an engineered tissue, and the first study to quantify pyridinoline cross-link development over time in a self-assembling tissue. Additionally, this work shows the relative contributions of collagen and pyridinoline to the tensile properties of collagenous tissue for the first time. Furthermore, this is the first investigation to identify a relationship between qMRI metrics and the pyridinoline cross-link content of an engineered collagenous tissue. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Characterizing the temperature dependence of electronic packaging-material properties

NASA Astrophysics Data System (ADS)

Fu, Chia-Yu; Ume, Charles

1995-06-01

A computer-controlled, temperature-dependent material characterization system has been developed for thermal deformation analysis in electronic packaging applications, especially for printed wiring assembly warpage study. For fiberglass-reinforced epoxy (FR-4 type) material, the Young's moduli decrease to as low as 20-30% of the room-temperature values, while the shear moduli decrease to as low as 60-70% of the room-temperature values. The electrical resistance strain gage technique was used in this research. The test results produced overestimated values in property measurements, and this was shown in a case study. A noncontact strau]n measurement technique (laser extensometer) is now being used to measure these properties. Discrepancies of finite-element warpage predictions using different property values increase as the temperature increases from the stress-free temperature.

Diagnostic monitor for carbon fiber processing

DOEpatents

Paulauskas, Felix L.; Bigelow, Timothy S.; Meek, Thomas T.

2002-01-01

A method for monitoring characteristics of materials includes placing a material in an application zone, measuring a change in at least one property value of the application zone caused by placing the material in the application zone and relating changes in the property value of the application zone caused by the material to at least one characteristic of the material An apparatus for monitoring characteristics of a material includes a measuring device for measuring a property value resulting from applying a frequency signal to the application zone after placing a material in the application zone and a processor for relating changes in the property value caused by placement of the material in the application zone to at least one desired characteristic of the material. The application zone is preferably a resonant cavity.

Relation of asphalt chemistry to physical properties and specifications.

DOT National Transportation Integrated Search

1984-01-01

This report constitutes a synthesis of published information concerning the chemical composition and characteristics of asphalt cements used in highway construction. The general relations between chemical composition and physical properties and speci...

Measurements of Aerosol Vertical Profiles and Optical Properties during INDOEX 1999 Using Micro-Pulse Lidars

NASA Technical Reports Server (NTRS)

Welton, Ellsworth J.; Voss, Kenneth J.; Quinn, Patricia K.; Flatau, Piotr J.; Markowicz, Krzysztof; Campbell, James R.; Spinhirne, James D.; Gordon, Howard R.; Johnson, James E.; Starr, David OC. (Technical Monitor)

2001-01-01

Micro-pulse lidar systems (MPL) were used to measure aerosol properties during the Indian Ocean Experiment (INDOEX) 1999 field phase. Measurements were made from two platforms: the NOAA ship RN Ronald H. Brown, and the Kaashidhoo Climate Observatory (KCO) in the Maldives. Sunphotometers were used to provide aerosol optical depths (AOD) needed to calibrate the MPL. This study focuses on the height distribution and optical properties (at 523 nm) of aerosols observed during the campaign. The height of the highest aerosols (top height) was calculated and found to be below 4 km for most of the cruise. The marine boundary layer (MBL) top was calculated and found to be less than 1 km. MPL results were combined with air mass trajectories, radiosonde profiles of temperature and humidity, and aerosol concentration and optical measurements. Humidity varied from approximately 80% near the surface to 50% near the top height during the entire cruise. The average value and standard deviation of aerosol optical parameters were determined for characteristic air mass regimes. Marine aerosols in the absence of any continental influence were found to have an AOD of 0.05 +/- 0.03, an extinction-to-backscatter ratio (S-ratio) of 33 +/- 6 sr, and peak extinction values around 0.05/km (near the MBL top). The marine results are shown to be in agreement with previously measured and expected values. Polluted marine areas over the Indian Ocean, influenced by continental aerosols, had AOD values in excess of 0.2, S-ratios well above 40 sr, and peak extinction values approximately 0.20/km (near the MBL top). The polluted marine results are shown to be similar to previously published values for continental aerosols. Comparisons between MPL derived extinction near the ship (75 m) and extinction calculated at ship-level using scattering measured by a nephelometer and absorption using a PSAP were conducted. The comparisons indicated that the MPL algorithm (using a constant S-ratio throughout the lower troposphere) calculates extinction near the surface in agreement with the ship-level measurements only when the MBL aerosols are well mixed with aerosols above. Finally, a review of the MPL extinction profiles showed that the model of aerosol vertical extinction developed during an earlier INDOEX field campaign (at the Maldives) did not correctly describe the true vertical distribution over the greater Indian Ocean region. Using the average extinction profile and AOD obtained during marine conditions, a new model of aerosol vertical extinction was determined for marine atmospheres over the Indian Ocean. A new model of aerosol vertical extinction for polluted marine atmospheres was also developed using the average extinction profile and AOD obtained during marine conditions influenced by continental aerosols.

Leveraged Leasing in the Federal Sector.

DTIC Science & Technology

1983-12-01

adjustments, is 90% or more of the fair value of the leased property. [Ref. 81 Capital type leases are classified as direct financing or sales type leases on...sales-type a profit or loss would occur [Ref. 7]. In a sales-type lease the fair value of the leased property at the inception of the lease differs...from the cost or carrying amount; in a direct financing lease, the fair value of the leased 28 property at the inception of the lease is the cost or

26 CFR 1.216-2 - Treatment as property subject to depreciation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... paragraph shall be the fair market value of such depreciable real property on the date of the conversion if the fair market value is less than the adjusted basis of such property in the hands of the cooperative housing corporation provided in section 1011 without taking into account any adjustment for depreciation...

12 CFR 217.32 - General risk weights.

Code of Federal Regulations, 2014 CFR

2014-01-01

... percent of the appraised value of the property; A Board-regulated institution must base all estimates of a property's value on an appraisal or evaluation of the property that satisfies subpart E of 12 CFR part 208... depository institutions or in transit, and to gold bullion held in a subsidiary depository institution's own...

Capitalization of Charter Schools into Residential Property Values

ERIC Educational Resources Information Center

Brehm, Margaret; Imberman, Scott A.; Naretta, Michael

2017-01-01

Although prior research has found clear impacts of schools and school quality on property values, little is known about whether charter schools have similar effects. Using sale price data for residential properties in Los Angeles County from 2008 to 2011 we estimate the neighborhood level impact of charter schools on housing prices. Using an…

26 CFR 20.2013-3 - “Second limitation”.

Code of Federal Regulations, 2014 CFR

2014-04-01

... computed by subtracting from the present decedent's gross estate the value of the property transferred (see... transferred property (see § 20.2013-4)) bears to H (the value of the present decedent's gross estate reduced... limitation”. (a) The amount of the Federal estate tax attributable to the transferred property in the present...

Short Communication: Heightened HIV Antibody Responses in Postpartum Women as Exemplified by Recent Infection Assays: Implications for Incidence Estimates.

PubMed

Hargrove, John W; van Schalkwyk, Cari; Humphrey, Jean H; Mutasa, Kuda; Ntozini, Robert; Owen, Sherry Michele; Masciotra, Silvina; Parekh, Bharat S; Duong, Yen T; Dobbs, Trudy; Kilmarx, Peter H; Gonese, Elizabeth

2017-09-01

Laboratory assays that identify recent HIV infections are important for assessing impacts of interventions aimed at reducing HIV incidence. Kinetics of HIV humoral responses can vary with inherent assay properties, and between HIV subtypes, populations, and physiological states. They are important in determining mean duration of recent infection (MDRI) for antibody-based assays for detecting recent HIV infections. We determined MDRIs for multi-subtype peptide representing subtypes B, E and D (BED)-capture enzyme immunoassay, limiting antigen (LAg), and Bio-Rad Avidity Incidence (BRAI) assays for 101 seroconverting postpartum women, recruited in Harare from 1997 to 2000 during the Zimbabwe Vitamin A for Mothers and Babies trial, comparing them against published MDRIs estimated from seroconverting cases in the general population. We also compared MDRIs for women who seroconverted either during the first 9 months, or at later stages, postpartum. At cutoffs (C) of 0.8 for BED, 1.5 for LAg, and 40% for BRAI, estimated MDRIs for postpartum mothers were 192, 104, and 144 days, 33%, 32%, and 52% lower than published estimates of 287, 152 and 298 days, respectively, for clade C samples from general populations. Point estimates of MDRI values were 7%-19% shorter for women who seroconverted in the first 9 months postpartum than for those seroconverting later. MDRI values for three HIV incidence biomarkers are longer in the general population than among postpartum women, particularly those who recently gave birth, consistent with heightened immunological activation soon after birth. Our results provide a caution that MDRI may vary significantly between subjects in different physiological states.

26 CFR 1.1019-1 - Property on which lessee has made improvements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Basis Rules of General Application § 1.1019-1... value of such property attributable to such buildings or improvements, the basis of each portion of such... building would have a depreciated value of $50,000, which value the lessor elected to report (beginning in...

26 CFR 1.1019-1 - Property on which lessee has made improvements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Basis Rules of General Application § 1.1019-1... value of such property attributable to such buildings or improvements, the basis of each portion of such... building would have a depreciated value of $50,000, which value the lessor elected to report (beginning in...

26 CFR 1.1019-1 - Property on which lessee has made improvements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Basis Rules of General Application § 1.1019-1... value of such property attributable to such buildings or improvements, the basis of each portion of such... building would have a depreciated value of $50,000, which value the lessor elected to report (beginning in...

26 CFR 1.1019-1 - Property on which lessee has made improvements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Basis Rules of General Application § 1.1019-1... value of such property attributable to such buildings or improvements, the basis of each portion of such... building would have a depreciated value of $50,000, which value the lessor elected to report (beginning in...

20 CFR 362.12 - Computation of amount of reimbursement.

Code of Federal Regulations, 2011 CFR

2011-04-01

... paid in cash for the property or, if not acquired by purchase or exchange, the value at the time of acquisition. The amount normally payable on property damaged beyond economical repair is found by determining its depreciated value immediately before it was damaged or lost, less any salvage value. If the cost...

Compilation of PZC and IEP of sparingly soluble metal oxides and hydroxides from literature.

PubMed

Kosmulski, Marek

2009-11-30

The values of PZC and IEP of metal oxides reported in the literature are affected by the choice of the specimens to be studied. The specimens, which have PZC and IEP similar to the "recommended" value, are preferred by the scientists. The biased choice leads to accumulation of results for a few specimens, and the other specimens are seldom studied or they are subjected to washing procedures aimed at shift of the original IEP toward the "recommended" value. Taking the average or median of all published PZC and IEP for certain oxide as the "recommended" value leads to substantiation of previously published results due to overrepresentation of certain specimens in the sample.

Impact of Wetting/Oven-Drying Cycles on the Mechanical and Physical Properties of Birch Plywood

NASA Astrophysics Data System (ADS)

Sooru, M.; Kasepuu, K.; Kask, R.; Lille, H.

2015-11-01

The objective of this study was to explore some physical and mechanical properties and the dimensional stability of birch (Betula sp.) nine-ply veneers glued with phenol-formaldehyde (PF) after 10 cycles of soaking/oven-drying. The properties to be determined were bending strength (BS), modulus of elasticity in bending (MOE), Janka hardness (JH) and thickness swelling (TS), which were tested according to the European Standards (EN). An analytical equation was used for approximation of the change in the physical and mechanical properties of the samples depending on the number of cycles. It was shown that the values of the studied properties were affected most by the first soaking and drying cycles after which BS and MOE decreased continuously while the values of JH and TS stabilized. After 10 cycles the final values of BS, MOE, JH and TS accounted for 75-81%, 95%, 82% and 98.5% of the initial values, respectively.

Evaluation of the yield, molar mass of exopolysaccharides, and rheological properties of gels formed during fermentation of milk by Streptococcus thermophilus strains St-143 and ST-10255y.

PubMed

Khanal, Som N; Lucey, John A

2017-09-01

The yield and chemical structures of exopolysaccharides (EPS) produced by many strains of Streptococcus thermophilus have been characterized. However, the kinetics (or production profile) for EPS during milk fermentation is not clear. In this study, we investigated whether any differences existed in the yield and molar mass of EPS when milk was fermented at the same acidification rate by 2 strains of S. thermophilus (St-143 and ST-10255y). The type of EPS produced by these 2 strains is different. Milk samples were analyzed for EPS concentration every 30 min during a fermentation period of 270 min (final pH 4.5) by using a modified quantification method, which was faster and validated for its recovery of added EPS. Rheological properties of milks during fermentation were also analyzed using small-strain dynamic oscillatory rheology. For the determination of molar mass, EPS extracts were isolated by ultrafiltration of whey obtained during fermentation of milk to pH values 5.2, 4.9, 4.7, and 4.5, and molar mass was analyzed using size-exclusion chromatography-multi-angle laser light scattering. During fermentation, both strains appeared to start producing significant amounts of EPS after about ∼150 min, which corresponded to pH ∼5.3, which was close to the point of gelation. During the remainder of the fermentation process (150-270 min), the EPS concentration from strains St-143 and ST-10255y significantly increased from 30 to 72 mg/L and from 26 to 56 mg/L, respectively. The quantity of EPS recovered by our modified method was estimated to represent ∼60% of the total EPS added to milk. The molar mass of EPS produced by both strains appeared to slightly decrease during fermentation. At pH 5.2, EPS from St-143 and ST-10255y had molar masses of 2.9 × 10 6 and 1.4 × 10 6 g/mol, respectively, which decreased to 1.6 × 10 6 and 0.8 × 10 6 g/mol, respectively, when the pH of milk was 4.5. Distinct differences were apparent in the rheological properties of gels fermented by the 2 strains. At the end of fermentation, St-143 fermented milk had weaker gels with storage modulus (G') value at pH 4.6 of 26 Pa, whereas gels made with ST-10255y were stiffer with a G' value at pH 4.6 of 82 Pa. For St-143 gels, maximum loss tangent (LT max ) values were higher (0.50) and occurred earlier (at a higher pH value) than the LT max values (0.46) for gels from ST-10255y strain. Because the fermentation conditions were identical for both strains, the observed changes in rheological properties could be due to the differences in chemical structures and molar mass of the EPS produced by these 2 S. thermophilus strains. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Multi-crosswell profile 3D imaging and method

DOEpatents

Washbourne, John K.; Rector, III, James W.; Bube, Kenneth P.

2002-01-01

Characterizing the value of a particular property, for example, seismic velocity, of a subsurface region of ground is described. In one aspect, the value of the particular property is represented using at least one continuous analytic function such as a Chebychev polynomial. The seismic data may include data derived from at least one crosswell dataset for the subsurface region of interest and may also include other data. In either instance, data may simultaneously be used from a first crosswell dataset in conjunction with one or more other crosswell datasets and/or with the other data. In another aspect, the value of the property is characterized in three dimensions throughout the region of interest using crosswell and/or other data. In still another aspect, crosswell datasets for highly deviated or horizontal boreholes are inherently useful. The method is performed, in part, by fitting a set of vertically spaced layer boundaries, represented by an analytic function such as a Chebychev polynomial, within and across the region encompassing the boreholes such that a series of layers is defined between the layer boundaries. Initial values of the particular property are then established between the layer boundaries and across the subterranean region using a series of continuous analytic functions. The continuous analytic functions are then adjusted to more closely match the value of the particular property across the subterranean region of ground to determine the value of the particular property for any selected point within the region.

Detailed Project Report. Small Beach Erosion Control Project. Broadkill Beach, Delaware.

DTIC Science & Technology

1972-02-01

this study. TABLE 3 ESTIMATED PROPERTY VALUES IN BROADKILL BEACH (July 1971) Beach Front Property* Entire Community Present Present Fair Value Fair ...between the 14th and 50th year reflect only the land, houses and utilities (minus salvage value estimated at 25% of the fair value ) that are located... Value $ $ 1,221,000 2,866,000 ftExcluding beach area. >4’ 5 11. The water entering Delaware Bay from Delaware River is polluted, but the degree of

The Four Ps of Publishing: Demystifying Publishing in Peer-Reviewed Journals for Social Work Doctoral Students

ERIC Educational Resources Information Center

Bender, Kimberly; Windsor, Liliane Cambraia

2010-01-01

Since the 1990s, the field of social work has placed substantial value on social work research. As a result, publishing has become an important aspect of contributing to the social work field. While encouragement for faculty to publish may vary across settings, publication has not traditionally been expected of doctoral students. The purpose of…

Introduction to physical properties and elasticity models: Chapter 20

USGS Publications Warehouse

Dvorkin, Jack; Helgerud, Michael B.; Waite, William F.; Kirby, Stephen H.; Nur, Amos

2003-01-01

Estimating the in situ methane hydrate volume from seismic surveys requires knowledge of the rock physics relations between wave speeds and elastic moduli in hydrate/sediment mixtures. The elastic moduli of hydrate/sediment mixtures depend on the elastic properties of the individual sedimentary particles and the manner in which they are arranged. In this chapter, we present some rock physics data currently available from literature. The unreferenced values in Table I were not measured directly, but were derived from other values in Tables I and II using standard relationships between elastic properties for homogeneous, isotropic material. These derivations allow us to extend the list of physical property estimates, but at the expense of introducing uncertainties due to combining property values measured under different physical conditions. This is most apparent in the case of structure II (sII) hydrate for which very few physical properties have been measured under identical conditions.

Occurrence and distribution of algal biomass and Its relation to nutrients and selected basin characteristics in Indiana streams, 2001-2005

USGS Publications Warehouse

Lowe, B. Scott; Leer, Donald R.; Frey, Jeffrey W.; Caskey, Brian J.

2008-01-01

The seasonal values for nutrients (nitrate, TKN, TN, and TP) and algal biomass (periphyton CHLa, AFDM, seston CHLa, and POC) were compared to published U. S. Environmental Protection Agency (USEPA) values for their respective ecoregions. Algal biomass values either were greater than the 25th percentile published USEPA values or extended the range of data in Aggregate Nutrient Ecoregions VI, VII, IX and USEPA Level III Ecoregions 54, 55, 56, 71, and 72. If the values for the 25th percentile proposed by the USEPA were adopted as nutrient water-quality criteria, then about 71 percent of the nutrient samples and 57 percent of the CHLa samples within the eight study basins would be considered nutrient enriched.

36 CFR 262.12 - Impounding of personal property.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of the trespass is mailed by registered mail or delivered to such owner. (b) In the event the local... 15 days after the date a notice of intention to impound the property in trespass is first published... the site occupied during the period of the trespass. (d) If the personal property is not redeemed on...

77 FR 51948 - Airport Improvement Program (AIP): Policy Regarding Access to Airports From Residential Property...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-28

...-0754] Airport Improvement Program (AIP): Policy Regarding Access to Airports From Residential Property... Airports From Residential Property that was published in the Federal Register on July 30, 2012. The FAA is... policy, based on Federal law, concerning through-the- fence access to a federally obligated airport from...

Comparison of spatially and temporally resolved diffuse transillumination measurement systems for extraction of optical properties of scattering media.

PubMed

Ortiz-Rascón, E; Bruce, N C; Garduño-Mejía, J; Carrillo-Torres, R; Hernández-Paredes, J; Álvarez-Ramos, M E

2017-11-20

This paper discusses the main differences between two different methods for determining the optical properties of tissue optical phantoms by fitting the spatial and temporal intensity distribution functions to the diffusion approximation theory. The consistency in the values of the optical properties is verified by changing the width of the recipient containing the turbid medium; as the optical properties are an intrinsic value of the scattering medium, independently of the recipient width, the stability in these values for different widths implies a better measurement system for the acquisition of the optical properties. It is shown that the temporal fitting method presents higher stability than the spatial fitting method; this is probably due to the addition of the time of flight parameter into the diffusion theory.

77 FR 66464 - Federal Acquisition Regulation; Submission for OMB Review; Value Engineering Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-05

...; Submission for OMB Review; Value Engineering Requirements AGENCIES: Department of Defense (DOD), General... collection requirement concerning Value Engineering Requirements. A notice was published in the Federal... comments identified by Information Collection 9000- 0027, Value Engineering Requirements, by any of the...