Science.gov

Sample records for pure normal loading

  1. Lateral Stress Measurements in Pure Tungsten during Shock Loading

    SciTech Connect

    Millett, J. C. F.; Gray, G. T. III; Bourne, N. K.

    2006-07-28

    Longitudinal and lateral stresses during the shock loading of pure tungsten have been measured using manganin stress gauges. The Hugoniot has been compared to the previous work of others and shown to be in close agreement. Lateral stresses have been shown to increase behind the shock front, implying that the shear strength decreases. Whilst this is similar to results in tantalum, comparison with recovery experiments in the literature suggests that this may be due in part to a brittle failure process.

  2. Distribution Characteristics of Normal Pure-Tone Thresholds

    PubMed Central

    Margolis, Robert H.; Wilson, Richard H.; Popelka, Gerald R.; Eikelboom, Robert H.; Swanepoel, De Wet; Saly, George L.

    2016-01-01

    Objective This study examined the statistical properties of normal air-conduction thresholds obtained with automated and manual audiometry to test the hypothesis that thresholds are normally distributed and to examine the distributions for evidence of bias in manual testing. Design Four databases were mined for normal thresholds. One contained audiograms obtained with an automated method. The other three were obtained with manual audiometry. Frequency distributions were examined for four test frequencies (250, 500, 1000, and 2000 Hz). Study Sample The analysis is based on 317,569 threshold determinations of 80,547 subjects from four clinical databases. Results Frequency distributions of thresholds obtained with automated audiometry are normal in form. Corrected for age, the mean thresholds are within 1.5 dB of Reference Equivalent Threshold Sound Pressure Levels. Frequency distributions of thresholds obtained by manual audiometry are shifted toward higher thresholds. Two of the three datasets obtained by manual audiometry are positively skewed. Conclusions The positive shift and skew of the manual audiometry data may result from tester bias. The striking scarcity of thresholds below 0 dB HL suggests that audiologists place less importance on identifying low thresholds than they do for higher-level thresholds. We refer to this as the Good Enough Bias and suggest that it may be responsible for differences in distributions of thresholds obtained by automated and manual audiometry. PMID:25938502

  3. Optical based tactile shear and normal load sensor

    SciTech Connect

    Salisbury, Curt Michael

    2015-06-09

    Various technologies described herein pertain to a tactile sensor that senses normal load and/or shear load. The tactile sensor includes a first layer and an optically transparent layer bonded together. At least a portion of the first layer is made of optically reflective material. The optically transparent layer is made of resilient material (e.g., clear silicone rubber). The tactile sensor includes light emitter/light detector pair(s), which respectively detect either normal load or shear load. Light emitter(s) emit light that traverses through the optically transparent layer and reflects off optically reflective material of the first layer, and light detector(s) detect and measure intensity of reflected light. When a normal load is applied, the optically transparent layer compresses, causing a change in reflected light intensity. When shear load is applied, a boundary between optically reflective material and optically absorptive material is laterally displaced, causing a change in reflected light intensity.

  4. Revival of pure titanium for dynamically loaded porous implants using additive manufacturing.

    PubMed

    Wauthle, Ruben; Ahmadi, Seyed Mohammad; Amin Yavari, Saber; Mulier, Michiel; Zadpoor, Amir Abbas; Weinans, Harrie; Van Humbeeck, Jan; Kruth, Jean-Pierre; Schrooten, Jan

    2015-09-01

    Additive manufacturing techniques are getting more and more established as reliable methods for producing porous metal implants thanks to the almost full geometrical and mechanical control of the designed porous biomaterial. Today, Ti6Al4V ELI is still the most widely used material for porous implants, and none or little interest goes to pure titanium for use in orthopedic or load-bearing implants. Given the special mechanical behavior of cellular structures and the material properties inherent to the additive manufacturing of metals, the aim of this study is to investigate the properties of selective laser melted pure unalloyed titanium porous structures. Therefore, the static and dynamic compressive properties of pure titanium structures are determined and compared to previously reported results for identical structures made from Ti6Al4V ELI and tantalum. The results show that porous Ti6Al4V ELI still remains the strongest material for statically loaded applications, whereas pure titanium has a mechanical behavior similar to tantalum and is the material of choice for cyclically loaded porous implants. These findings are considered to be important for future implant developments since it announces a potential revival of the use of pure titanium for additively manufactured porous implants.

  5. Revival of pure titanium for dynamically loaded porous implants using additive manufacturing.

    PubMed

    Wauthle, Ruben; Ahmadi, Seyed Mohammad; Amin Yavari, Saber; Mulier, Michiel; Zadpoor, Amir Abbas; Weinans, Harrie; Van Humbeeck, Jan; Kruth, Jean-Pierre; Schrooten, Jan

    2015-09-01

    Additive manufacturing techniques are getting more and more established as reliable methods for producing porous metal implants thanks to the almost full geometrical and mechanical control of the designed porous biomaterial. Today, Ti6Al4V ELI is still the most widely used material for porous implants, and none or little interest goes to pure titanium for use in orthopedic or load-bearing implants. Given the special mechanical behavior of cellular structures and the material properties inherent to the additive manufacturing of metals, the aim of this study is to investigate the properties of selective laser melted pure unalloyed titanium porous structures. Therefore, the static and dynamic compressive properties of pure titanium structures are determined and compared to previously reported results for identical structures made from Ti6Al4V ELI and tantalum. The results show that porous Ti6Al4V ELI still remains the strongest material for statically loaded applications, whereas pure titanium has a mechanical behavior similar to tantalum and is the material of choice for cyclically loaded porous implants. These findings are considered to be important for future implant developments since it announces a potential revival of the use of pure titanium for additively manufactured porous implants. PMID:26046272

  6. Investigation of Cyclic Deformation and Fatigue of Polycrystalline Cu under Pure Compression Cyclic Loading Conditions

    NASA Astrophysics Data System (ADS)

    Hsu, Tzu-Yin Jean

    It is commonly accepted that fatigue crack is initiated under tensile fatigue stresses. However, practical examples demonstrate that cracks may also initiate under pure compressive fluctuating loads such as the failures observed in aircraft landing gear frames. However, the mechanism of such failures is rarely investigated. Furthermore, knowledge on cyclic deformation response under pure compressive fatigue condition is also very limited or non-existent. Our recent work already verified that fatigue cracks may nucleate from stress concentration sites under pure compression fatigue, but whether or not a form of stress concentration is always needed to initiate a crack under pure compression fatigue remains uncertain. In this study, compression fatigue tests under different peak stresses were carried out on smooth bars of fully annealed OFHC Copper. The purpose of these tests is to investigate not only the cyclic deformation response but also the possibility of crack nucleation without the stress concentrator. Results showed that overall the cyclic stress-strain response and microstructural evolution of OFHC Copper under pure compression fatigue exhibits rather dissimilar behaviour compared to those under symmetrical fatigue. The specimens hardened rapidly within 10 cycles under pure compression fatigue unlike the gradual cyclic hardening behaviour in symmetrical fatigue with the same peak stress amplitude. Compressive cyclic creep behaviour was also observed under the same testing conditions. Moreover, unlike conventional tension-compression fatigue, only moderate slip activity was detectable on the surface instead of typical PSB features detected from TEM observations. The surface observations has revealed that surface slip bands did not increase in number nor did they become more pronounced in height with increasing number of cycles. In addition, surface roughening by grain boundary extrusion was detected to become more severe as the cycling progressed. Therefore

  7. Investigation of Cyclic Deformation and Fatigue of Polycrystalline Cu under Pure Compression Cyclic Loading Conditions

    NASA Astrophysics Data System (ADS)

    Hsu, Tzu-Yin Jean

    It is commonly accepted that fatigue crack is initiated under tensile fatigue stresses. However, practical examples demonstrate that cracks may initiate under pure compressive fluctuating loads, e.g. the failures observed in aircraft landing gear frames. As the mechanism of such failures is rarely investigated, there is very limited or non-existent knowledge pool on cyclic deformation response under pure compressive fatigue condition. Our recent work verified that fatigue cracks may nucleate from stress concentration sites under pure compression fatigue, but whether or not a form of stress concentration is always needed to initiate a crack remains uncertain. In this study, compression fatigue tests under different peak stresses were carried out on smooth bars of fully annealed OFHC Copper. The purpose of these tests is to investigate not only the cyclic deformation response but also the possibility of crack nucleation without the stress concentrator. Results showed that overall the cyclic stress-strain response and microstructural evolution of OFHC Copper under pure compression fatigue exhibits rather dissimilar behaviour compared to those under symmetrical fatigue. The specimens hardened rapidly within 10 cycles under pure compression fatigue unlike the gradual cyclic hardening behaviour in symmetrical fatigue with the same peak stress amplitude. Compressive cyclic creep behaviour was also observed. Moreover, TEM observation showed that only moderate slip activity was detectable on the surface instead of typical PSB features. The surface observations revealed that surface slip bands did not increase in number nor height as cycling progressed. In addition, surface roughening by grain boundary extrusion was detected to become more severe with further cycling. Therefore, the plastic strain accommodated within the samples was not mainly related to dislocation activities. Instead, the mechanism of cyclic creep response for pure compression fatigue was correlated and

  8. Computational modeling of dynamic mechanical properties of pure polycrystalline magnesium under high loading strain rates

    NASA Astrophysics Data System (ADS)

    Li, Qizhen

    2015-09-01

    Computational simulations were performed to investigate the dynamic mechanical behavior of pure polycrystalline magnesium under different high loading strain rates with the values of 800, 1000, 2000, and 3600 s-1. The Johnson-Cook model was utilized in the simulations based on finite element modeling. The results showed that the simulations provided well-matched predictions of the material behavior such as the strain rate-time history, the stress-strain curve, and the temperature increase. Under high loading strain rates, the tested material experienced linear strain hardening at the early stage of plastic deformation, increased strain hardening at the intermediate plastic deformation region, and decreased strain hardening at the region before fracture. The strain hardening rates for the studied high loading strain rate cases do not vary much with the change of strain rates.

  9. Ignition and Combustion Characteristics of Pure Bulk Metals: Normal-Gravity Test Results

    NASA Technical Reports Server (NTRS)

    Abbud-Madrid, A.; Fiechtner, G. J.; Branch, M. C.; Daily, J. W.

    1994-01-01

    An experimental apparatus has been designed for the study of bulk metal ignition under elevated, normal and reduced gravity environments. The present work describes the technical characteristics of the system, the analytical techniques employed, the results obtained from the ignition of a variety of metals subjected to normal gravity conditions and the first results obtained from experiments under elevated gravity. A 1000 W xenon short-arc lamp is used to irradiate the top surface of a cylindrical metal specimen 4 mm in diameter and 4 mm high in a quiescent pure-oxygen environment at 0.1 MPa. Iron, titanium, zirconium, magnesium, zinc, tin, and copper specimens are investigated. All these metals exhibit ignition and combustion behavior varying in strength and speed. Values of ignition temperatures below, above or in the range of the metal melting point are obtained from the temperature records. The emission spectra from the magnesium-oxygen gas-phase reaction reveals the dynamic evolution of the ignition event. Scanning electron microscope and x-ray spectroscopic analysis provide the sequence of oxide formation on the burning of copper samples. Preliminary results on the effect of higher-than-normal gravity levels on the ignition of titanium specimens is presented.

  10. Effects of a pure antiandrogen on gonadotropin secretion in normal women and in polycystic ovarian disease.

    PubMed

    Couzinet, B; Thomas, G; Thalabard, J C; Brailly, S; Schaison, G

    1989-07-01

    To assess the role of androgens in gonadotropin regulation in women, we studied the effects of a pure nonsteroidal antiandrogen, Anandron (Cassenne, Paris, France). Nine normally cycling women (group 1) with acne and/or seborrhoea and nine patients with polycystic ovarian disease (PCOD) (group 2) received Anandron (100 mg twice a day) and a placebo. Both treatments were administered orally, in a cross-over randomized design, for two consecutive cycles (group 1) or months (group 2) separated by one cycle or 1 month. Luteinizing hormone (LH) pulse frequency and amplitude (cluster analysis), basal and gonadotropin-releasing hormone (GnRH)-stimulated plasma LH/follicle-stimulating hormone (FSH) levels were determined on day 5 of each treatment or placebo cycle. On days 5, 10, 20, and 24 of each cycle or month, plasma estradiol (E2), estrone (E1), testosterone (T), dihydrotestosterone (DHT), androstenedione (A), dehydroepiandrosterone sulfate (DHAS), sex hormone-binding globulin (SHBG) levels, and urinary androstanediol glucuronide (3 alpha-diol G) were measured. Plasma progesterone (P) levels were determined on days 20 and 24 of each cycle (group 1) and on days 5, 10, 20, and 24 (group 2). In both groups, seborrhea and acne decreased markedly within the first month and practically disappeared after 2 months of Anandron treatment. No adverse side effects were reported. None of the normal patients had any disturbance of menstrual cycles as assessed by basal body temperature shift, ultrasonography, and plasma P levels. In PCOD patients, cycles remained anovulatory.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:2744186

  11. Perception of pure tones and iterated rippled noise for normal hearing and cochlear implant users.

    PubMed

    Penninger, Richard T; Chien, Wade W; Jiradejvong, Patpong; Boeke, Emily; Carver, Courtney L; Limb, Charles J

    2013-03-01

    Cochlear Implant (CI) users typically perform poorly on musical tasks, especially those based on pitch ranking and melody recognition. It was hypothesized that CI users would demonstrate deterioration in performance for a pitch ranking and a melody recognition task presented with iterated rippled noise (IRN) in comparison to pure tones (PT). In Addition, it was hypothesized that normal hearing (NH) listeners would show fewer differences in performance between IRN and PT for these two tasks. In this study, the ability of CI users and NH subjects to rank pitches and to identify melodies created with IRN and PT was assessed in free field in a sound-isolated room. CI subjects scored significantly above chance level with PT stimuli in both tasks. With IRN stimuli their performance was around chance level. NH subjects scored significantly above chance level in both tasks and with all stimuli. NH subjects performed significantly better than CI subjects in both tasks. These results illustrate the difficulties of CI subjects to rank pitches and to identify melodies. PMID:23539260

  12. Fracture toughness determination using spiral-grooved cylindrical specimen and pure torsional loading

    DOEpatents

    Wang, Jy-An; Liu, Kenneth C.

    2003-07-08

    A method for determining fracture toughness K.sub.IC of materials ranging from metallic alloys, brittle ceramics and their composites, and weldments. A cylindrical specimen having a helical V-groove with a 45.degree. pitch is subjected to pure torsion. This loading configuration creates a uniform tensile-stress crack-opening mode, and a transverse plane-strain state along the helical groove. The full length of the spiral groove is equivalent to the thickness of a conventional compact-type specimen. K.sub.IC values are determined from the fracture torque and crack length measured from the test specimen using a 3-D finite element program (TOR3D-KIC) developed for the purpose. In addition, a mixed mode (combined tensile and shear stress mode) fracture toughness value can be determined by varying the pitch of the helical groove. Since the key information needed for determining the K.sub.IC value is condensed in the vicinity of the crack tip, the specimen can be significantly miniaturized without the loss of generality.

  13. Modelling normal and impaired letter recognition: implications for understanding pure alexic reading.

    PubMed

    Chang, Ya-Ning; Furber, Steve; Welbourne, Stephen

    2012-10-01

    Letter recognition is the foundation of the human reading system. Despite this, it tends to receive little attention in computational modelling of single word reading. Here we present a model that can be trained to recognise letters in various spatial transformations. When presented with degraded stimuli the model makes letter confusion errors that correlate with human confusability data. Analyses of the internal representations of the model suggest that a small set of learned visual feature detectors support the recognition of both upper case and lower case letters in various fonts and transformations. We postulated that a damaged version of the model might be expected to act in a similar manner to patients suffering from pure alexia. Summed error score generated from the model was found to be a very good predictor of the reading times of pure alexic patients, outperforming simple word length, and accounting for 47% of the variance. These findings are consistent with a hypothesis suggesting that impaired visual processing is a key to understanding the strong word-length effects found in pure alexic patients. PMID:22841988

  14. Modular and scalable load-wall sled buck for pure-lateral and oblique side impact tests.

    PubMed

    Yoganandan, Narayan; Humm, John R; Pintar, Frank A

    2012-05-11

    A considerable majority of side impact sled tests using different types of human surrogates has used a load-wall design not specific to subject anthropometry. The use of one load-wall configuration cannot accurately isolate and evaluate regional responses for the same load-wall geometry. As the anatomy and biomechanical responses of the human torso depends on the region, and anthropomorphic test devices continue to advance and accommodate regional differences, it is important to obtain specific data from sled tests. To achieve this goal, the present study designed a scalable modular load-wall consisting of the shoulder, thorax, abdomen, and superior and inferior pelvis, and lower limb plates. The first five plates were connected to a vertical fixture and the limb plate was connected to another fixture. The width, height, and thickness, and the gap between plates were modular. Independent adjustments in the coronal and sagittal planes allowed region-specific positioning depending on surrogate anthropometry, example pelvis width and seated height. Two tri-axial load cells were fixed on the contralateral face of each plate of the load-wall to record impact force-time histories. The load-wall and vertical fixture design can be used to conduct side impact tests with varying vectors, pure-lateral to anterior and posterior oblique, by appropriately orienting the load-wall with respect to the surrogate. The feasibility of the design to extract region-specific biomechanical data was demonstrated by conducting pure-lateral and anterior oblique sled tests using two different surrogates at a velocity of 6.7m/s. Uses of this design are discussed for different applications.

  15. Effects of Load on Normal Human Osteoblast Function

    NASA Astrophysics Data System (ADS)

    Reseland, J. E.; Devakottai, Sundar; Sundaresan, A.

    2013-02-01

    The effects of load on the secretion and expression of bone markers were tested at different stages of differentiation of primary human osteoblasts. NHOs were both seeded with and without cytodex 3 beads (Sigma),transferred to a NASA rotating wall vessel (modeled microgravity) and harvested at day 7 and day 14. Differentiated and undifferentiated NHOs were loaded at 6-50G for 30 min and compared to cells incubated at 1G after 1 day and 3 days. Collectively the results demonstrate that load has a differential effect on osteoblast differentiation as seen in modeled microgravity and shows specificity in expression of bone cell markers vs. expression of secreted paracrine signaling markers.

  16. An efficient reliable method to estimate the vaporization enthalpy of pure substances according to the normal boiling temperature and critical properties.

    PubMed

    Mehmandoust, Babak; Sanjari, Ehsan; Vatani, Mostafa

    2014-03-01

    The heat of vaporization of a pure substance at its normal boiling temperature is a very important property in many chemical processes. In this work, a new empirical method was developed to predict vaporization enthalpy of pure substances. This equation is a function of normal boiling temperature, critical temperature, and critical pressure. The presented model is simple to use and provides an improvement over the existing equations for 452 pure substances in wide boiling range. The results showed that the proposed correlation is more accurate than the literature methods for pure substances in a wide boiling range (20.3-722 K).

  17. Ciliary activity under normal conditions and under viscous load.

    PubMed

    Gheber, L; Priel, Z

    1990-01-01

    Ciliary metachronism and motility were examined optically in muco-ciliary tissue cultures from three different systems: a) frog's palate epithelium, b) frog's oesophagus, and c) human nasal polyps. In addition, lateral cilia of Mytilus edulis (water transporting cilia) were examined. It was revealed that the degree of synchronization between muco-ciliary systems is lower than that of water transporting cilia. There are no significant differences between different muco-ciliary systems, within the accuracy of our measurement although relatively large statistical ensembles were used. In addition the wavelength and wave direction of the metachronal wave was examined. All four systems exhibit similar wavelength. The metachronal parameters of muco-ciliary systems exhibit fluctuations (as was demonstrated by the degree of synchronization), however, the magnitude and repetitivity of these fluctuations, is dependent on the loading of the ciliary system. We have loaded the system by increasing the viscosity of the medium. Under viscous load the frequency of the beating decreased. The metachronal wavelength became longer and the metachronal coordination type more orthoplectic.

  18. Pure Ethiodized Oil-based Transcatheter Ablative Therapy in Normal Rabbit Kidneys and Kidneys Inoculated with VX-2 Carcinoma

    SciTech Connect

    Konya, Andras; Stephens, L. Clifton; Wright, Kenneth C.

    2011-10-15

    Purpose: To evaluate the efficacy of ablation with selective arterial injection of pure ethiodized oil followed by arterial occlusion with 9:1 ethanol-Ethiodol mixture (EEM) and coil placement in normal rabbit kidneys and kidneys inoculated with VX-2 carcinoma. Materials and Methods: All experiments were conducted with Animal Care and Use Committee approval. In six rabbits (group 1), one kidney was embolized with pure Ethiodol until capillary stasis, followed by injection of 9:1 EEM until arterial stasis and then coil placement into the main renal artery. In 12 other rabbits, one kidney was inoculated with VX-2 tumor. Ethiodol and EEM embolization and coil placement followed 7 days later (group 2, n = 6) or 11-14 days later (group 3, n = 6). Kidneys were evaluated (angiography, computed tomography, macro- and microscopy) 7 days after treatment. Results: Capillary stasis was achieved in groups 1, 2, and 3 with (mean {+-} standard deviation) 0.47 {+-} 0.03, 0.53 {+-} 0.02, and 0.56 {+-} 0.04 ml of pure Ethiodol, followed by 0.47 {+-} 0.05, 0.42 {+-} 0.03, and 0.38 {+-} 0.04 ml of EEM, respectively, which caused complete arterial occlusion in 17 of 18 kidneys. In group 1, all but one kidney showed at least 95% generalized coagulative necrosis. In group 2, all six kidneys exhibited 100% coagulative necrosis, with no viable tumor present. In group 3, 100% coagulative necrosis was present in all kidneys, with a small viable tumor in one. Conclusion: In the rabbit, selective arterial injection of pure Ethiodol can cause complete renal parenchyma and tumor ablation when it is followed by prompt, contiguous, and permanent occlusion of the arterial compartment.

  19. Comparison of Intervertebral ROM in Multi-Level Cadaveric Lumbar Spines Using Distinct Pure Moment Loading Approaches

    PubMed Central

    Santoni, Brandon; Cabezas, Andres F; Cook, Daniel J; Yeager, Matthew S; Billys, James B; Whiting, Benjamin

    2015-01-01

    Background Pure-moment loading is the test method of choice for spinal implant evaluation. However, the apparatuses and boundary conditions employed by laboratories in performing spine flexibility testing vary. The purpose of this study was to quantify the differences, if they exist, in intervertebral range of motion (ROM) resulting from different pure-moment loading apparatuses used in two laboratories. Methods Twenty-four (laboratory A) and forty-two (laboratory B) intact L1-S1 specimens were loaded using pure moments (±7.5 Nm) in flexion-extension (FE), lateral bending (LB) and axial torsion (AT). At laboratory A, pure moments were applied using a system of cables, pulleys and suspended weights in 1.5 Nm increments. At laboratory B, specimens were loaded in a pneumatic biaxial test frame mounted with counteracting stepper-motor-driven biaxial gimbals. ROM was obtained in both labs using identical optoelectronic systems and compared. Results In FE, total L1-L5 ROM was similar, on average, between the two laboratories (lab A: 37.4° ± 9.1°; lab B: 35.0° ± 8.9°, p=0.289). Larger apparent differences, on average, were noted between labs in AT (lab A: 19.4° ± 7.3°; lab B: 15.7° ± 7.1°, p=0.074), and this finding was significant for combined right and left LB (lab A: 45.5° ± 11.4°; lab B: 35.3° ± 8.5°, p < 0.001). Conclusions To our knowledge, this is the first study comparing ROM of multi-segment lumbar spines between laboratories utilizing different apparatuses. The results of this study show that intervertebral ROM in multi-segment lumbar spine constructs are markedly similar in FE loading. Differences in boundary conditions are likely the source of small and sometimes statistically significant differences between the two techniques in LB and AT ROM. The relative merits of each testing strategy with regard to the physiologic conditions that are to be simulated should be considered in the design of a study including LB and AT modes of loading. An

  20. Table and Charts of Equilibrium Normal-shock Properties for Pure Hydrogen with Velocities to 70 km/sec. Revised.

    NASA Technical Reports Server (NTRS)

    Miller, C. G., III; Wilder, S. E.

    1976-01-01

    Errors found in the original edition are corrected. Refinement was made in procedures for solving the conservation relations for an incident (moving), standing, and reflected normal shock, as well as in computational methods for determining thermochemical-equilibrium hydrogen properties. A six-species hydrogen model replaces the original four-species model, and the heat of formation and spectroscopic constants used in this six-species model are listed in appendix A. In appendix B, comparisons are made between a number of methods for determining equilibrium thermodynamic properties for hydrogen for several values of pressure and temperatures to 50000 K. A comparison is also performed between the present method and a second method for determining thermodynamic properties and flow velocity behind an incident shock into pure hydrogen and behind a reflected shock.

  1. Propagation of the transverse normal stress in a thick plate due to distributed lateral impulsive loadings

    NASA Technical Reports Server (NTRS)

    Oline, L. W.

    1972-01-01

    A theoretical study of the elastic stresses produced in an infinite plate when struck by a high-speed object is presented. The solution is obtained by means of linear elasticity. Laplace transformation techniques are employed to solve the axisymmetric problem. The plate is loaded normal to its surface with a uniform load over a circular area. The normal stress at the wave front of the unreflected dilatation wave along the axis and its variation with the radius of loading are determined. Various facets of the problem are discussed.

  2. 46 CFR 112.30-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ....30-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatically Connected Storage Battery as the Sole Emergency Power Source § 112.30-3 Normal source for emergency loads. (a) The normal...

  3. Strength degradation and lifetime prediction of dental zirconia ceramics under cyclic normal loading.

    PubMed

    Li, Wanzhong; Xu, Yingqiang; He, Huiming; Zhao, Haidan; Sun, Jian; Hou, Yue

    2015-01-01

    Clinical cases show that zirconia restoration could happen fracture by accident under overloading after using a period of time. The purpose of this study is to research mechanical behavior and predict lifetime of dental zirconia ceramics under cyclic normal contact loading with experiments. Cyclic normal contact loading test and three point bending test are carried on specimens made of two brands of dental zirconia ceramic to obtain flexure strength and damage degree after different number of loading cycles. By means of damage mechanics model, damage degree under different number of contact loading cycles are calculated according to flexure strength, and verified by SEM photographs of cross section morphology of zirconia ceramics specimen phenomenologically. Relation curve of damage degree and number of cycles is fitted by polynomial fitting, then the number of loading cycles can be concluded when the specimen is complete damage. Strength degradation of two brands dental zirconia ceramics are researched in vitro, and prediction method of contact fatigue lifetime is established.

  4. Structure of a micro hollow cathode discharge in the normal regime at medium pressure range in pure argon

    NASA Astrophysics Data System (ADS)

    Lazzaroni, Claudia; Chabert, Pascal; Rousseau, Antoine; Sadeghi, Nader

    2009-10-01

    A microplasma is generated in the 400 μm diameter micro hole of a molybdenum-alumina-molybdenum sandwich (MHCD type) at medium pressure (30-300Torr) in pure argon. Experiments are performed during the normal regime, when the plasma is not only confined in the hole but also expands on the cathode backside. Imaging and emission spectroscopy allows the discharge structure to be studied and is used to infer the electronic density in the micro-hole via the Stark broadening of the Hβ line. We find strong maxima of the plasma emission in the vicinity of the sheath edge. To explain some of the experimental observations, we use a one dimensional transport model to obtain the radial evolution of the charged-particles densities and fluxes. The result of this model is used as an input parameter of a sheath-model which allows the sheath thickness to be calculated as a function of pressure. The sheath size variation with pressure is well correlated with the maxima of plasma emission.

  5. Inspiratory and expiratory resistive load detection in normal and asthmatic subjects. A sensory decision theory analysis.

    PubMed

    Bonnel, A M; Mathiot, M J; Grimaud, C

    1985-01-01

    The ability to detect added external inspiratory and expiratory resistive loads was studied in normal and asthmatic subjects using sensory decision theory as a psychophysical method. Performances P(A)/delta R [where P(A) represents the index of sensitivity and delta R the additional resistor] were similar in normal and asthmatic subjects, but when sensitivity was expressed in relation to airway resistance [P(A)/delta R/Raw], asthmatics showed higher inspiratory and expiratory performances than normal subjects. After bronchodilation the relative sensitivity in the asthmatic group was impaired and approached that of normal subjects. Comparing inspiratory and expiratory load detection, normal subjects showed a higher sensitivity for expiratory than for inspiratory loads. In contrast, there was no difference in the asthmatic group. The response bias remained the same across conditions. If one accepts the assumption that the variability of sensitivity presented by asthmatic and normal subjects might be related to the variable state of their pulmonary function, our results can be interpreted as demonstrating a relationship between sensitivity and pulmonary distension or airway obstruction. These results are in agreement with the hypothesis that the site of perception for respiratory load detection is the chest wall. PMID:4023435

  6. Controlling the number of graphene sheets exfoliated from graphite by designed normal loading and frictional motion

    SciTech Connect

    Lee, Seungjun; Lu, Wei

    2014-07-14

    We use molecular dynamics to study the exfoliation of patterned nanometer-sized graphite under various normal loading conditions for friction-induced exfoliation. Using highly ordered pyrolytic graphite (HOPG) as well as both amorphous and crystalline SiO{sub 2} substrate as example systems, we show that the exfoliation process is attributed to the corrugation of the HOPG surface and the atomistic roughness of the substrate when they contact under normal loading. The critical normal strain, at which the exfoliation occurs, is higher on a crystalline substrate than on an amorphous substrate. This effect is related to the atomistic flatness and stiffness of the crystalline surface. We observe that an increase of the van der Waals interaction between the graphite and the substrate results in a decrease of the critical normal strain for exfoliation. We find that the magnitude of the normal strain can effectively control the number of exfoliated graphene layers. This mechanism suggests a promising approach of applying designed normal loading while sliding to pattern controlled number of graphene layers or other two-dimensional materials on a substrate surface.

  7. Transverse Stress Decay in a Specially Orthotropic Strip Under Localizing Normal Edge Loading

    NASA Technical Reports Server (NTRS)

    Fichter, W. B.

    2000-01-01

    Solutions are presented for the stresses in a specially orthotropic infinite strip which is subjected to localized uniform normal loading on one edge while the other edge is either restrained against normal displacement only, or completely fixed. The solutions are used to investigate the diffusion of load into the strip and in particular the decay of normal stress across the width of the strip. For orthotropic strips representative of a broad range of balanced and symmetric angle-ply composite laminates, minimum strip widths are found that ensure at least 90% decay of the normal stress across the strip. In addition, in a few cases where, on the fixed edge the peak shear stress exceeds the normal stress in magnitude, minimum strip widths that ensure 90% decay of both stresses are found. To help in putting these results into perspective, and to illustrate the influence of material properties on load 9 orthotropic materials, closed-form solutions for the stresses in similarly loaded orthotropic half-planes are obtained. These solutions are used to generate illustrative stress contour plots for several representative laminates. Among the laminates, those composed of intermediate-angle plies, i.e., from about 30 degrees to 60 degrees, exhibit marked changes in normal stress contour shape with stress level. The stress contours are also used to find 90% decay distances in the half-planes. In all cases, the minimum strip widths for 90% decay of the normal stress exceed the 90% decay distances in the corresponding half-planes, in amounts ranging from only a few percent to about 50% of the half-plane decay distances. The 90% decay distances depend on both material properties and the boundary conditions on the supported edge.

  8. 46 CFR 112.30-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Normal source for emergency loads. 112.30-3 Section 112.30-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatically Connected Storage Battery...

  9. 46 CFR 112.35-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Normal source for emergency loads. 112.35-3 Section 112.35-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Manually Controlled Emergency Systems Having a Storage Battery or...

  10. 46 CFR 112.30-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Normal source for emergency loads. 112.30-3 Section 112.30-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatically Connected Storage Battery...

  11. 46 CFR 112.35-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Normal source for emergency loads. 112.35-3 Section 112.35-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Manually Controlled Emergency Systems Having a Storage Battery or...

  12. 46 CFR 112.30-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Normal source for emergency loads. 112.30-3 Section 112.30-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatically Connected Storage Battery...

  13. 46 CFR 112.35-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Normal source for emergency loads. 112.35-3 Section 112.35-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Manually Controlled Emergency Systems Having a Storage Battery or...

  14. 46 CFR 112.30-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Normal source for emergency loads. 112.30-3 Section 112.30-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatically Connected Storage Battery...

  15. 46 CFR 112.35-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Normal source for emergency loads. 112.35-3 Section 112.35-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Manually Controlled Emergency Systems Having a Storage Battery or...

  16. 46 CFR 112.25-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Normal source for emergency loads. 112.25-3 Section 112.25-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatic Starting Diesel Engine or...

  17. 46 CFR 112.25-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Normal source for emergency loads. 112.25-3 Section 112.25-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatic Starting Diesel Engine or...

  18. 46 CFR 112.25-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Normal source for emergency loads. 112.25-3 Section 112.25-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatic Starting Diesel Engine or...

  19. 46 CFR 112.25-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Normal source for emergency loads. 112.25-3 Section 112.25-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatic Starting Diesel Engine or...

  20. 46 CFR 112.25-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Normal source for emergency loads. 112.25-3 Section 112.25-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Systems Having an Automatic Starting Diesel Engine or...

  1. Effects of Dynamic Multi-directional Loading on the Microstructural Evolution and Thermal Stability of Pure Aluminum

    NASA Astrophysics Data System (ADS)

    Yang, Yang; Zhang, Hua; Chen, Yadong

    2016-09-01

    Microstructural evolution and thermal stability of 1050 commercial pure aluminum processed by means of split Hopkinson pressure bar and Instron-3369 mechanical testing machine to an accumulated strain of 3.6 were investigated. The nominal strain rates reached up to 3.0 × 103 and 1 × 10-3/s, respectively. Samples in the deformed state and annealed in the temperature interval 423-523 K for 1 h were characterized by transmission electron microscopy (TEM). TEM observations reveal that the initial coarse grains are refined significantly, and the deformed structures mainly consist of equiaxed subgrains and dislocation cells with a high density of interior dislocation. In addition, the average subgrain/cell sizes of these two kinds of deformed samples are nearly the same. As to recovery behavior, recovered subgrains are observed at 473 (dynamic) versus 523 K (quasi-static), that is to say, recovery is fairly slow in the quasi-static deformed samples. It is therefore to be expected that thermal stability of this dynamic deformed aluminum is weaker than that of the quasi-static compressed one, which is due to the higher density of dislocation and nonequilibrium dislocation configurations produced during dynamic loading.

  2. Effects of Dynamic Multi-directional Loading on the Microstructural Evolution and Thermal Stability of Pure Aluminum

    NASA Astrophysics Data System (ADS)

    Yang, Yang; Zhang, Hua; Chen, Yadong

    2016-07-01

    Microstructural evolution and thermal stability of 1050 commercial pure aluminum processed by means of split Hopkinson pressure bar and Instron-3369 mechanical testing machine to an accumulated strain of 3.6 were investigated. The nominal strain rates reached up to 3.0 × 103 and 1 × 10-3/s, respectively. Samples in the deformed state and annealed in the temperature interval 423-523 K for 1 h were characterized by transmission electron microscopy (TEM). TEM observations reveal that the initial coarse grains are refined significantly, and the deformed structures mainly consist of equiaxed subgrains and dislocation cells with a high density of interior dislocation. In addition, the average subgrain/cell sizes of these two kinds of deformed samples are nearly the same. As to recovery behavior, recovered subgrains are observed at 473 (dynamic) versus 523 K (quasi-static), that is to say, recovery is fairly slow in the quasi-static deformed samples. It is therefore to be expected that thermal stability of this dynamic deformed aluminum is weaker than that of the quasi-static compressed one, which is due to the higher density of dislocation and nonequilibrium dislocation configurations produced during dynamic loading.

  3. Strength degradation and lifetime prediction of dental zirconia ceramics under cyclic normal loading.

    PubMed

    Li, Wanzhong; Xu, Yingqiang; He, Huiming; Zhao, Haidan; Sun, Jian; Hou, Yue

    2015-01-01

    Clinical cases show that zirconia restoration could happen fracture by accident under overloading after using a period of time. The purpose of this study is to research mechanical behavior and predict lifetime of dental zirconia ceramics under cyclic normal contact loading with experiments. Cyclic normal contact loading test and three point bending test are carried on specimens made of two brands of dental zirconia ceramic to obtain flexure strength and damage degree after different number of loading cycles. By means of damage mechanics model, damage degree under different number of contact loading cycles are calculated according to flexure strength, and verified by SEM photographs of cross section morphology of zirconia ceramics specimen phenomenologically. Relation curve of damage degree and number of cycles is fitted by polynomial fitting, then the number of loading cycles can be concluded when the specimen is complete damage. Strength degradation of two brands dental zirconia ceramics are researched in vitro, and prediction method of contact fatigue lifetime is established. PMID:26405889

  4. Evaluation of the Hinge Moment and Normal Force Aerodynamic Loads from a Seamless Adaptive Compliant Trailing Edge Flap in Flight

    NASA Technical Reports Server (NTRS)

    Miller, Eric J.; Cruz, Josue; Lung, Shun-Fat; Kota, Sridhar; Ervin, Gregory; Lu, Kerr-Jia; Flick, Pete

    2016-01-01

    A seamless adaptive compliant trailing edge (ACTE) flap was demonstrated in flight on a Gulfstream III aircraft at the NASA Armstrong Flight Research Center. The trailing edge flap was deflected between minus 2 deg up and plus 30 deg down in flight. The safety-of-flight parameters for the ACTE flap experiment require that flap-to-wing interface loads be sensed and monitored in real time to ensure that the structural load limits of the wing are not exceeded. The attachment fittings connecting the flap to the aircraft wing rear spar were instrumented with strain gages and calibrated using known loads for measuring hinge moment and normal force loads in flight. The safety-of-flight parameters for the ACTE flap experiment require that flap-to-wing interface loads be sensed and monitored in real time to ensure that the structural load limits of the wing are not exceeded. The attachment fittings connecting the flap to the aircraft wing rear spar were instrumented with strain gages and calibrated using known loads for measuring hinge moment and normal force loads in flight. The interface hardware instrumentation layout and load calibration are discussed. Twenty-one applied calibration test load cases were developed for each individual fitting. The 2-sigma residual errors for the hinge moment was calculated to be 2.4 percent, and for normal force was calculated to be 7.3 percent. The hinge moment and normal force generated by the ACTE flap with a hinge point located at 26-percent wing chord were measured during steady state and symmetric pitch maneuvers. The loads predicted from analysis were compared to the loads observed in flight. The hinge moment loads showed good agreement with the flight loads while the normal force loads calculated from analysis were over-predicted by approximately 20 percent. Normal force and hinge moment loads calculated from the pressure sensors located on the ACTE showed good agreement with the loads calculated from the installed strain gages.

  5. Intraocular pressure effects of water loading and venous compression tests in normal and denervated pigmented rabbits.

    PubMed

    Gual, A; Mintenig, G M; Belmonte, C

    1989-03-01

    We have compared IOP elevations induced by water-loading and by increased cephalic venous pressure in normal and denervated pigmented rabbits. Denervations were performed by sympathetic ganglionectomy and/or blockade of the sensory and autonomic innervation of the eye through retrobulbar anesthesia; retrobulbar anesthesia induced significant decreases of the basal IOP in control but not in ganglionectomized eyes. The water-loading test induced a peak pressure elevation approximately 30 min after water administration that could be counteracted by retrobulbar anesthesia. Ganglionectomized rabbits exhibited steeper IOP rises and greater IOP increases following water-loading than the control eyes; retrobulbar anesthesia in ganglionectomized eyes delayed the IOP response to water-loading. Compressions of the neck lasting 30 min elicited significant IOP elevations that were more pronounced in ganglionectomized eyes. In these eyes, retrobulbar anesthesia further increased the IOP rise elicited by neck compression. An IOP decrease below control values was observed at the end of the venous compression. The results indicate that an intact efferent innervation of the eye contributes to buffer IOP elevations induced by water-loading or cephalic venous stasis, presumably through the vascular effects of the ocular autonomic nerves.

  6. Skew-normal/independent linear mixed models for censored responses with applications to HIV viral loads

    PubMed Central

    Bandyopadhyay, Dipankar; Lachos, Victor H.; Castro, Luis M.; Dey, Dipak K.

    2012-01-01

    Often in biomedical studies, the routine use of linear mixed-effects models (based on Gaussian assumptions) can be questionable when the longitudinal responses are skewed in nature. Skew-normal/elliptical models are widely used in those situations. Often, those skewed responses might also be subjected to some upper and lower quantification limits (viz. longitudinal viral load measures in HIV studies), beyond which they are not measurable. In this paper, we develop a Bayesian analysis of censored linear mixed models replacing the Gaussian assumptions with skew-normal/independent (SNI) distributions. The SNI is an attractive class of asymmetric heavy-tailed distributions that includes the skew-normal, the skew-t, skew-slash and the skew-contaminated normal distributions as special cases. The proposed model provides flexibility in capturing the effects of skewness and heavy tail for responses which are either left- or right-censored. For our analysis, we adopt a Bayesian framework and develop a MCMC algorithm to carry out the posterior analyses. The marginal likelihood is tractable, and utilized to compute not only some Bayesian model selection measures but also case-deletion influence diagnostics based on the Kullback-Leibler divergence. The newly developed procedures are illustrated with a simulation study as well as a HIV case study involving analysis of longitudinal viral loads. PMID:22685005

  7. Annual Variation of Seismicity due to Surface Loads in Normal Fault Systems in Southern Tibet

    NASA Astrophysics Data System (ADS)

    Tian, Y.; Luo, Y.; Li, Y.; Wang, X.; Zhang, J.

    2014-12-01

    It had been found that there are seasonal variations of seismicity related to surface hydrology at Main Himalaya Thrust (MHT) fault. In this work, we analyzed the historical micro-earthquakes recorded by China Digital Seismograph Network (CSDN) in normal faulting systems in southern Tibet, to test whether such a phenomenon exist here and to figure out the possible modulation mechanism. There are several N-S striking normal fault systems (e.g. Yadong-Gulu, Shenza-Dingjie rifts) across the southern Tibetan plateau, which are supposed to accommodate the crust extension induced by Indo-Eurasia collision. The quake catalog covers the time span of 2008-2014. All quake events are relocated using the double-differencing method. The catalog was then declustered using CLUSTER2000 (http://earthquake.usgs.gov/research/software/). The declustered catalog was then averaged for one-month period. The monthly catalog shows that the number of earthquake is maximum during the winter months (from January to March), although the maximum values do not agree for individual years (Fig. 1). Such a variation is similar to that found at MHT. Contrary to the situation at MHT (thrust fault), we found it might be explained directly by surface mass redistributions. The contemporary continuous GPS observations confirm that Tibetan plateau crust moves up and down periodically and reaches its lowest position in summer under the surface hydrological load. According to the Coulomb failure criterion (S=τ-μ(σn-pf) , where S is Coulomb Stress, σn is normal stress, τ is shear stress), an increase of mass load in summer in Tibet will cause an increase in normal stress at the (gently dipping) fault plane and accordingly a decrease in Coulomb stress, which thus inhibits the occurrence of quakes on those normal fault planes.

  8. A Comparison between the cytotoxic effects of pure curcumin and curcumin-loaded PLGA-PEG nanoparticles on the MCF-7 human breast cancer cell line.

    PubMed

    Tabatabaei Mirakabad, Fatemeh Sadat; Akbarzadeh, Abolfazl; Milani, Morteza; Zarghami, Nosratollah; Taheri-Anganeh, Mortaza; Zeighamian, Vahideh; Badrzadeh, Fariba; Rahmati-Yamchi, Mohammad

    2016-01-01

    Breast cancer is the most commonly diagnosed cancer and the leading cause of cancer death among women worldwide. Herbal medicines have tremendous potential as promising agents for the treatment of cancer. Curcumin is a natural polyphenol which has many anticancer effects. Because of its low aqueous solubility, low bioavailability, and quick degradation and metabolism, curcumin was released using PLGA-PEG nanoparticles. Herein, the efficiency of pure curcumin and curcumin-loaded PLGA-PEG in MCF-7 human breast cancer cell lines was studied. (1)H NMR, FT-IR and SEM demonstrated PLGA-PEG structure and curcumin loaded on nanoparticles. Subsequently, the cytotoxic effects of free curcumin and curcumin-loaded PLGA-PEG were determined via an MTT assay. Our study confirmed that curcumin-loaded PLGA-PEG has more cytotoxic effects on the MCF-7 breast cancer cell line and could be exploited as a potential source for developing novel drugs against breast cancer.

  9. Dependence of normal development of skeletal muscle in neonatal rats on load bearing

    NASA Technical Reports Server (NTRS)

    Ohira, Y.; Tanaka, T.; Yoshinaga, T.; Kawano, F.; Nomura, T.; Nonaka, I.; Allen, D. L.; Roy, R. R.; Edgerton, V. R.

    2000-01-01

    Antigravity function plays an important role in determining the morphological and physiological properties of the neuromuscular system. Inhibition of the normal development of the neuromuscular system is induced by hindlimb unloading during the neonatal period in rats. However, the role of gravitational loading on the development of skeletal muscle in rats is not well understood. It could be hypothesized that during the early postnatal period, i.e. when minimal weight-supporting activity occurs, the activity imposed by gravity would be of little consequence in directing the normal development of the skeletal musculature. We have addressed this issue by limiting the amount of postnatal weight-support activity of the hindlimbs of rats during the lactation period. We have focused on the development of three characteristics of the muscle fibers, i.e. size, myonuclear number and myosin heavy chain expression.

  10. Experimental validation of normalized uniform load surface curvature method for damage localization.

    PubMed

    Jung, Ho-Yeon; Sung, Seung-Hoon; Jung, Hyung-Jo

    2015-10-16

    In this study, we experimentally validated the normalized uniform load surface (NULS) curvature method, which has been developed recently to assess damage localization in beam-type structures. The normalization technique allows for the accurate assessment of damage localization with greater sensitivity irrespective of the damage location. In this study, damage to a simply supported beam was numerically and experimentally investigated on the basis of the changes in the NULS curvatures, which were estimated from the modal flexibility matrices obtained from the acceleration responses under an ambient excitation. Two damage scenarios were considered for the single damage case as well as the multiple damages case by reducing the bending stiffness (EI) of the affected element(s). Numerical simulations were performed using MATLAB as a preliminary step. During the validation experiments, a series of tests were performed. It was found that the damage locations could be identified successfully without any false-positive or false-negative detections using the proposed method. For comparison, the damage detection performances were compared with those of two other well-known methods based on the modal flexibility matrix, namely, the uniform load surface (ULS) method and the ULS curvature method. It was confirmed that the proposed method is more effective for investigating the damage locations of simply supported beams than the two conventional methods in terms of sensitivity to damage under measurement noise.

  11. Normalization.

    ERIC Educational Resources Information Center

    Cuevas, Eduardo J.

    1997-01-01

    Discusses cornerstone of Montessori theory, normalization, which asserts that if a child is placed in an optimum prepared environment where inner impulses match external opportunities, the undeviated self emerges, a being totally in harmony with its surroundings. Makes distinctions regarding normalization, normalized, and normality, indicating how…

  12. Table and charts of equilibrium normal shock and shock tube properties for pure argon with velocities to 18 km/sec

    NASA Technical Reports Server (NTRS)

    Miller, C. G., III; Wilder, S. E.

    1976-01-01

    Equilibrium thermodynamic and flow properties are presented in tabulated and graphical form for moving, standing, and reflected normal shock waves in pure argon. Properties include pressure, temperature, density, enthalpy, speed of sound, entropy, molecular-weight ratio, isentropic exponent, velocity, and species mole fractions. Incident (moving) shock velocities are varied from 2 to 18 km/sec for a range of initial pressure of 5 N/sq m to 500 kN/sq m. Working charts illustrating shock tube performance with argon test gas and heated helium and hydrogen driver gases are also presented.

  13. How the differential load induced by normal fault scarps controls the distribution of monogenic volcanism

    NASA Astrophysics Data System (ADS)

    Maccaferri, Francesco; Acocella, Valerio; Rivalta, Eleonora

    2016-04-01

    Understanding shallow magma transfer and the related vent distribution is crucial for volcanic hazard. In the present study we investigate the link between the stress induced by topographic scarps and the distribution of monogenic volcanoes at divergent plate boundaries. With a numerical model of dyke propagation we show that vertical dykes beneath a normal fault scarp tend to deflect towards the footwall side of the scarp. This effect increases with the scarp height, is stronger for dykes propagating underneath the hanging wall side, and decreases with the distance from the scarp. A comparison to the East African Rift System, Afar and Iceland shows that: 1) the inner rift structure, which shapes the topography, controls shallow dyke propagation; 2) differential loading due to mass redistribution affects magma propagation over a broad scale range (100 - 105 m). Our results find application to any volcanic field with tectonics- or erosion-induced topographic variations.

  14. How the differential load induced by normal fault scarps controls the distribution of monogenic volcanism

    NASA Astrophysics Data System (ADS)

    Maccaferri, F.; Acocella, V.; Rivalta, E.

    2015-09-01

    Understanding shallow magma transfer and the related vent distribution is crucial for volcanic hazard. Here we investigate how the stress induced by topographic scarps linked to normal faults affects the distribution of monogenic volcanoes at divergent plate boundaries. Our numerical models of dyke propagation below a fault scarp show that the dykes tend to propagate toward and erupt on the footwall side. This effect, increasing with the scarp height, is stronger for dykes propagating underneath the hanging wall side and decreases with the distance from the scarp. A comparison to the East African Rift System, Afar and Iceland shows that (1) the inner rift structure, which shapes the topography, controls shallow dyke propagation; (2) differential loading due to mass redistribution affects magma propagation over a broad scale range (100-105 m). Our results find application to any volcanic field with tectonics- or erosion-induced topographic variations and should be considered in any volcanic hazard assessment.

  15. Periodontal disease associates with higher brain amyloid load in normal elderly.

    PubMed

    Kamer, Angela R; Pirraglia, Elizabeth; Tsui, Wai; Rusinek, Henry; Vallabhajosula, Shankar; Mosconi, Lisa; Yi, Li; McHugh, Pauline; Craig, Ronald G; Svetcov, Spencer; Linker, Ross; Shi, Chen; Glodzik, Lidia; Williams, Schantel; Corby, Patricia; Saxena, Deepak; de Leon, Mony J

    2015-02-01

    The accumulation of amyloid-β (Aβ) plaques is a central feature of Alzheimer's disease (AD). First reported in animal models, it remains uncertain if peripheral inflammatory and/or infectious conditions in humans can promote Aβ brain accumulation. Periodontal disease, a common chronic infection, has been previously reported to be associated with AD. Thirty-eight cognitively normal, healthy, and community-residing elderly (mean age, 61 and 68% female) were examined in an Alzheimer's Disease Research Center and a University-Based Dental School. Linear regression models (adjusted for age, apolipoprotein E, and smoking) were used to test the hypothesis that periodontal disease assessed by clinical attachment loss was associated with brain Aβ load using (11)C-Pittsburgh compound B (PIB) positron emission tomography imaging. After adjusting for confounders, clinical attachment loss (≥3 mm), representing a history of periodontal inflammatory/infectious burden, was associated with increased PIB uptake in Aβ vulnerable brain regions (p = 0.002). We show for the first time in humans an association between periodontal disease and brain Aβ load. These data are consistent with the previous animal studies showing that peripheral inflammation/infections are sufficient to produce brain Aβ accumulations.

  16. Periodontal disease associates with higher brain amyloid load in normal elderly

    PubMed Central

    Kamer, Angela R.; Pirraglia, Elizabeth; Tsui, Wai; Rusinek, Henry; Vallabhajosula, Shankar; Mosconi, Lisa; Yi, Li; McHugh, Pauline; Craig, Ronald G.; Svetcov, Spencer; Linker, Ross; Shi, Chen; Glodzik, Lidia; Williams, Schantel; Corby, Patricia; Saxena, Deepak; de Leon, Mony J.

    2015-01-01

    Background The accumulation of amyloid β plaques (Aβ) is a central feature of Alzheimer’s disease (AD). First reported in animal models, it remains uncertain if peripheral inflammatory/infectious conditions in humans can promote Aβ brain accumulation. Periodontal disease, a common chronic infection, has been previously reported to be associated with AD. Methods Thirty-eight cognitively normal, healthy, community residing elderly (mean age 61; 68% female) were examined in an Alzheimer’s Disease research center and a University-based Dental School. Linear regression models (adjusted for age, ApoE and smoking) were used to test the hypothesis that periodontal disease assessed by clinical attachment loss was associated with brain Aβ load using 11C-PIB PET imaging. Results After adjusting for confounders, clinical attachment loss (≥ 3mm), representing a history of periodontal inflammatory/infectious burden, was associated with increased 11C-PIB uptake in Aβ vulnerable brain regions (p=0.002). Conclusion We show for the first time in humans an association between periodontal disease and brain Aβ load. These data are consistent with prior animal studies showing that peripheral inflammation/infections are sufficient to produce brain Aβ accumulations. PMID:25491073

  17. Effect of adhesive interleaving and discontinuous plies on failure of composite laminates subject to transverse normal loads

    NASA Technical Reports Server (NTRS)

    Jegley, Dawn C.

    1989-01-01

    Results of a series of tests to determine the effects of adhesive interleaving and discontinuous plies (plies with end-to-end gaps) on the displacements, failure loads and failure modes of graphite-epoxy laminates subjected to transverse normal loads are presented. Adhesive interleaving can be used to contain local damage within a group of plies, i.e., to arrest crack propagation on the interlaminate level, and it can increase the amount of normal displacement the laminate can withstand before failure. However, the addition of adhesive interleaving to a laminate does not significantly increase its load carrying capability. A few discontinuous plies in a laminate can reduce the normal displacement and load at failure by 10 to 40 percent compared to a laminate with no discontinuous plies, but the presence of the ply discontinuities does not generally change the failure location or the failure mode of the laminate.

  18. Optical triggering of 4H-SiC thyristors (18 kV class) to high currents in purely inductive load circuit

    NASA Astrophysics Data System (ADS)

    Rumyantsev, S. L.; Levinshtein, M. E.; Saxena, T.; Shur, M. S.; Cheng, L.; Palmour, J. W.; Agarwal, A.

    2014-11-01

    Optical switch-on of a very high voltage (18 kV class) 4H-SiC thyristor with an amplification step (pilot thyristor) to the current Imax = 1225 A is demonstrated using a purely inductive load and a calibrated air transformer. Increasing the inductance of the transformer primary winding slows down the turn on process. However, the inductance has little effect during the initial stage of the switch-on process when the voltage drop on the thyristor and its internal resistance is high. The results show that a further switch-on current increase can be only achieved by introducing additional amplification steps in the pilot thyristor.

  19. Differences in plantar loading between flat and normal feet during different athletic tasks.

    PubMed

    Queen, Robin M; Mall, Nathan A; Nunley, James A; Chuckpaiwong, Bavornrit

    2009-06-01

    The purpose of this study was to determine if foot type (flat or normal) resulted in loading differences during four sport-specific tasks (cross-cut, side-cut, shuttle run, and landing from a simulated lay-up). Twenty-two healthy subjects (12 normal feet and 10 flat feet) completed five trials in each condition, while in-shoe pressure data was collected at 50 Hz. Contact area, maximum force, and the force time integral were analyzed under the entire foot and in eight-foot regions. Foot type was determined by examining navicular height, arch angle, rearfoot angle, and a clinical score. A series of independent sample t-tests were used to determine statistical differences (alpha<0.05). During the cross-cut, flat feet demonstrated an increase in medial midfoot contact area. During the side-cut, flat feet demonstrated an increase in contact area, force time integral and maximum force in both the medial and lateral midfoot. During the shuttle run, flat feet demonstrated an increase in force time integral in the lateral midfoot and increases in maximum force in both the medial and lateral midfoot. During the landing task, flat feet demonstrated an increase in maximum force in the medial midfoot. However, flat feet demonstrate a decrease in middle forefoot maximum force. All results were statistically significant (p<0.05). Therefore, individuals with a normal foot could be at a lower risk for medial and lateral midfoot injuries such as metatarsal stress fractures, indicating that foot type should be assessed when determining an individual's risk for metatarsal stress fractures.

  20. Pure titanium particle loaded nanocomposites: study on the polymer/filler interface and hMSC biocompatibility.

    PubMed

    Avolio, Roberto; D'Albore, Marietta; Guarino, Vincenzo; Gentile, Gennaro; Cocca, Maria Cristina; Zeppetelli, Stefania; Errico, Maria Emanuela; Avella, Maurizio; Ambrosio, Luigi

    2016-10-01

    The integration of inorganic nanoparticles into polymer matrices allows for the modification of physical properties as well as the implementation of new features for unexplored application fields. Here, we propose the study of a new metal/polymer nanocomposite fabricated by dispersing pure Ti nanoparticles into a poly(methylmetacrilate) matrix via solvent casting process, to investigate its potential use as new biomaterial for biomedical applications. We demonstrated that Ti nanoparticles embedded in the poly(methylmetacrilate) matrix can act as reinforcing agent, not negatively influencing the biological response of human mesenchymal stem cell in terms of cytotoxicity and cell viability. As a function of relative amount and surface treatment, Ti nanoparticles may enhance mechanical strength of the composite-ranging from 31.1 ± 2.5 to 43.7 ± 0.7 MPa-also contributing to biological response in terms of adhesion and proliferation mechanisms. In particular, for 1 wt% Ti, treated Ti nanoparticles improve cell materials recognition, as confirmed by higher cell spreading-quantified in terms of cell area via image analysis-locally promoting stronger interactions at cell matrix interface. At this stage, these preliminary results suggest a promising use of pure Ti nanoparticles as filler in polymer composites for biomedical applications. PMID:27585912

  1. Pure titanium particle loaded nanocomposites: study on the polymer/filler interface and hMSC biocompatibility.

    PubMed

    Avolio, Roberto; D'Albore, Marietta; Guarino, Vincenzo; Gentile, Gennaro; Cocca, Maria Cristina; Zeppetelli, Stefania; Errico, Maria Emanuela; Avella, Maurizio; Ambrosio, Luigi

    2016-10-01

    The integration of inorganic nanoparticles into polymer matrices allows for the modification of physical properties as well as the implementation of new features for unexplored application fields. Here, we propose the study of a new metal/polymer nanocomposite fabricated by dispersing pure Ti nanoparticles into a poly(methylmetacrilate) matrix via solvent casting process, to investigate its potential use as new biomaterial for biomedical applications. We demonstrated that Ti nanoparticles embedded in the poly(methylmetacrilate) matrix can act as reinforcing agent, not negatively influencing the biological response of human mesenchymal stem cell in terms of cytotoxicity and cell viability. As a function of relative amount and surface treatment, Ti nanoparticles may enhance mechanical strength of the composite-ranging from 31.1 ± 2.5 to 43.7 ± 0.7 MPa-also contributing to biological response in terms of adhesion and proliferation mechanisms. In particular, for 1 wt% Ti, treated Ti nanoparticles improve cell materials recognition, as confirmed by higher cell spreading-quantified in terms of cell area via image analysis-locally promoting stronger interactions at cell matrix interface. At this stage, these preliminary results suggest a promising use of pure Ti nanoparticles as filler in polymer composites for biomedical applications.

  2. The ASSR: clinical application in normal-hearing and hearing-impaired infants and adults, comparison with the click-evoked ABR and pure-tone audiometry.

    PubMed

    Scherf, Fanny; Brokx, Jan; Wuyts, Floris L; Van de Heyning, Paul H

    2006-05-01

    The objective of this study was to investigate the clinical application of the ASSR (GSI Audera). It was completed in two parts: Study 1. Correlation between the ASSR-based threshold estimations and the conventional pure-tone thresholds in adults; and Study 2. Correlation between the average of the 2-4 kHz ASSR-based threshold estimations and c-ABR thresholds in children. The ASSRs were recorded in awake adults and sleeping infants with a range of hearing loss at CFs of 0.5 to 4 kHz and MFs between 46 and 95 Hz. The results show that in hearing-impaired adults (thresholds > 40 dBHL) good correlations can be observed between the behavioural thresholds and the ASSR-based threshold estimations. For the normal- to near-normal-hearing adults, a significant correspondence exists between the ASSR-based threshold estimations and FPTA. In children, strong correlations were found between the c-ABR and the 2-4 kHz ASSR-based threshold estimation average. These studies illustrate that the GSI Audera ASSR can accurately predict the behavioural audiogram in hearing-impaired subjects. In subjects with normal hearing the individual ASSR-based threshold estimations scatter too much. Instead the average of the ASSR-based threshold estimations corresponds well with the FPTA. PMID:16717018

  3. Tables and charts of equilibrium normal shock and shock tube solutions for pure CO2 with velocities to 16 km/second

    NASA Technical Reports Server (NTRS)

    Miller, C. G., III; Wilder, S. E.

    1974-01-01

    Equilibrium thermodynamic and flow properties are presented in tabulated and graphical form for moving, standing, and reflected normal shock waves in pure CO2, representative of Mars and Venus atmospheres. Properties include pressure, temperature, density, enthalpy, speed of sound, entropy, molecular weight ratio, isentropic exponent, velocity and species mole fractions. Incident (moving) shock velocities are varied from 1 to 16 km/sec for a range of initial pressure of 5 Newtons per square meter to 500 kilo Newtons per square meter. The present results are applicable to shock tube flows, and to free-flight conditions for a blunt body at high velocities. Working charts illustrating idealized shock-tube performance with CO2 test gas and heated helium and hydrogen driver gases are also presented.

  4. Table and charts of equilibrium normal-shock and shock-tube properties for pure carbon dioxide with velocities from 1 to 16 km/sec

    NASA Technical Reports Server (NTRS)

    Miller, C. G., III; Wilder, S. E.

    1976-01-01

    Equilibrium thermodynamic and flow properties are presented in tabulated and graphical form for moving, standing, and reflected normal shock waves in pure CO2. Properties include pressure, temperature, density, enthalpy, speed of sound, entropy, molecular weight ratio, isentropic exponent, velocity, and species mole fractions. Incident (moving) shock velocities are varied from 1 to 16 km/sec for a range of initial pressure of 5 N/sq m to 500 kN/sq m. The present results are applicable to shock tube flows and to freeflight conditions for a blunt body at high velocities. Working charts illustrating idealized shock tube performance with CO2 test gas and heated helium and hydrogen driver gases are also presented.

  5. Influence of normal loads and sliding velocities on friction properties of engineering plastics sliding against rough counterfaces

    NASA Astrophysics Data System (ADS)

    Nuruzzaman, D. M.; Chowdhury, M. A.; Rahaman, M. L.; Oumer, A. N.

    2016-02-01

    Friction properties of plastic materials are very important under dry sliding contact conditions for bearing applications. In the present research, friction properties of engineering plastics such as polytetrafluoroethylene (PTFE) and nylon are investigated under dry sliding contact conditions. In the experiments, PTFE and nylon slide against different rough counterfaces such as mild steel and stainless steel 316 (SS 316). Frictional tests are carried out at low loads 5, 7.5 and 10 N, low sliding velocities 0.5, 0.75 and 1 m/s and relative humidity 70%. The obtained results reveal that friction coefficient of PTFE increases with the increase in normal loads and sliding velocities within the observed range. On the other hand, frictional values of nylon decrease with the increase in normal loads and sliding velocities. It is observed that in general, these polymers show higher frictional values when sliding against SS 316 rather than mild steel. During running-in process, friction coefficient of PTFE and nylon steadily increases with the increase in rubbing time and after certain duration of rubbing, it remains at steady level. At identical operating conditions, the frictional values are significantly different depending on normal load, sliding velocity and material pair. It is also observed that in general, the influence of normal load on the friction properties of PTFE and nylon is greater than that of sliding velocity.

  6. The role of the mobility law of dislocations in the plastic response of shock loaded pure metals

    NASA Astrophysics Data System (ADS)

    Gurrutxaga-Lerma, Beñat

    2016-08-01

    This article examines the role that the choice of a dislocation mobility law has in the study of plastic relaxation at shock fronts. Five different mobility laws, two of them phenomenological fits to data, and three more based on physical models of dislocation inertia, are tested by employing dynamic discrete dislocation plasticity (D3P) simulations of a shock loaded aluminium thin foil. It is found that inertial laws invariably entail very short acceleration times for dislocations changing their kinematic state. As long as the mobility laws describe the same regime of terminal speeds, all mobility laws predict the same degree of plastic relaxation at the shock front. This is used to show that the main factor affecting plastic relaxation at the shock front is in fact the speed of dislocations.

  7. Pure and palladium-loaded Co3O4 hollow hierarchical nanostructures with giant and ultraselective chemiresistivity to xylene and toluene.

    PubMed

    Hwang, Su-Jin; Choi, Kwon-Il; Yoon, Ji-Wook; Kang, Yun Chan; Lee, Jong-Heun

    2015-04-01

    Pure and palladium-loaded Co3O4 hollow hierarchical nanostructures consisting of nanosheets have been prepared by solvothermal self-assembly. The nanostructures exhibited an ultrahigh response and selectivity towards p-xylene and toluene. The responses (resistance ratio) of the palladium-loaded Co3O4 hollow hierarchical nanostructures to 5 ppm of p-xylene and toluene were as high as 361 and 305, respectively, whereas the selectivity values (response ratios) towards p-xylene and toluene over interference from ethanol were 18.1 and 16.1, respectively. We attributed the giant response and unprecedented high selectivity towards methylbenzenes to the abundant adsorption of oxygen by Co3O4, the high chemiresistive variation in the Co3O4 nanosheets (thickness≈11 nm), and the catalytic promotion of the specific gas-sensing reaction. The morphological design of the p-type Co3O4 nanostructures and loading of the palladium catalyst have paved a new way to monitoring the most representative indoor air pollutants in a highly selective, sensitive, and reliable manner.

  8. Effect of sustained inspiratory loading on respiratory sensation and CO2 responsiveness in normal humans.

    PubMed

    Clague, J E; Carter, J; Pearson, M G; Calverley, P M

    1996-10-01

    1. To examine the effects of sustained resistive loading on the relationship between inspiratory effort sensation and respiratory drive (P0.1) and to determine if the change in CO2 responsiveness after sustained loading is accompanied by altered effort perception, hypercapnic responses were measured before, immediately after and 15 min after sustained resistive loading in seven subjects (six men, one woman). Sustained resistive loading was set to exceed a diaphragm tension-time index of 0.2. 2. Mean time to task failure during sustained loading was 17.7 min (range 12.5-22.5 min). The mean inspiratory effort sensation score rose from 3.4 (SEM 0.8) to 8.1 (0.8), whereas P0.1 fell from 29.5 (3.6) to 18.1 (3.6) cmH2O. 3. Immediately after loading the slopes of the ventilatory and sensory responses to CO2 fell (ventilatory response: before loading 16.7 (2.4) lmin-1kPa-1, immediately after loading 7.88 (2.18)lmin-1kPa-1; sensory response: before loading 1.95 (0.38) units/kPa; immediately after loading 1.12 (0.38) units/kPa; P < 0.05. Changes reverted to preloading levels by 15 min. 4. Sustained loading can lead to a dissociation between respiratory drive, as reflected by P0.1, and inspiratory effort sensation, and this disturbance can persist once the load is removed. Impaired sensory perception may be the primary determinant of the change in CO2 responsiveness seen after sustained resistive loading. PMID:8983879

  9. Racial and gender effects on pure-tone thresholds and distortion-product otoacoustic emissions (DPOAEs) in normal-hearing young adults.

    PubMed

    Dreisbach, Laura E; Kramer, Steven J; Cobos, Sandra; Cowart, Kristin

    2007-08-01

    This study examined racial and gender effects on behavioral thresholds and distortion-product otoacoustic emissions (DPOAEs) in the same subjects. Pure-tone behavioral thresholds and DPOAEs were measured in 60 young normal-hearing adult subjects (20 Caucasian, 20 Asian, 20 African-American, with ten females and ten males in each group). Behavioral thresholds were measured from 1000 through 16,000 Hz using Békèsy tracking. A DPOAE frequency sweep was measured with primary stimulus levels of L(1)/L(2)=60/45 dB SPL, and an f(2)/f(1) of 1.2 at discrete f(2) frequencies between 2000 through 12,000 Hz for each subject. Significant racial and gender differences in behavioral thresholds were found at 14,000 and 16,000 Hz, with the African Americans and females having the best hearing sensitivity. Based on the current results, similar findings for DPOAE frequency sweeps can be expected amongst different racial groups given that no significant differences were identified between the groups. To further define the effects of race and gender on auditory measures, future studies should include larger numbers of subjects, measurement of body size and middle ear reflectance, and examine emission generators. PMID:17654083

  10. Repeatability of the Evaluation of Perception of Dyspnea in Normal Subjects Assessed Through Inspiratory Resistive Loads

    PubMed Central

    Fernandes, Andréia K; Ziegler, Bruna; Konzen, Glauco L; Sanches, Paulo R.S; Müller, André F; Pereira, Rosemary P; Dalcin, Paulo de Tarso R

    2014-01-01

    Purpose: Study the repeatability of the evaluation of the perception of dyspnea using an inspiratory resistive loading system in healthy subjects. Methods: We designed a cross sectional study conducted in individuals aged 18 years and older. Perception of dyspnea was assessed using an inspiratory resistive load system. Dyspnea was assessed during ventilation at rest and at increasing resistive loads (0.6, 6.7, 15, 25, 46.7, 67, 78 and returning to 0.6 cm H2O/L/s). After breathing in at each level of resistive load for two minutes, the subject rated the dyspnea using the Borg scale. Subjects were tested twice (intervals from 2 to 7 days). Results: Testing included 16 Caucasian individuals (8 male and 8 female, mean age: 36 years). The median scores for dyspnea rating in the first test were 0 at resting ventilation and 0, 2, 3, 4, 5, 7, 7 and 1 point, respectively, with increasing loads. The median scores in the second test were 0 at resting and 0, 0, 2, 2, 3, 4, 4 and 0.5 points, respectively. The intra-class correlation coefficient was 0.57, 0.80, 0.74, 0.80, 0.83, 0.86, 0.91, and 0.92 for each resistive load, respectively. In a generalized linear model analysis, there was a statistically significant difference between the levels of resistive loads (p<0.001) and between tests (p=0.003). Dyspnea scores were significantly lower in the second test. Conclusion: The agreement between the two tests of the perception of dyspnea was only moderate and dyspnea scores were lower in the second test. These findings suggest a learning effect or an effect that could be at least partly attributed to desensitization of dyspnea sensation in the brain. PMID:25614771

  11. Preparation and properties of hydroxycamptothecin-loaded nanoparticles made of amphiphilic copolymer and normal polymer.

    PubMed

    Wang, Jinli; Wang, Rong; Li, Ling Bing

    2009-08-15

    Stabilized micelle structure nanoparticles were prepared using Pluronic F127 and poly(butylcyanoacrylate) (PBCA). To increase the drug loading of nanoparticles, D-alpha-tocopheryl polyethylene glycol 1000 succinate (TPGS) was additionally included into the nanoparticle composition. The poorly soluble anticancer drug 10-hydroxycamptothecin (HCPT) was used as a model drug and incorporated into nanoparticles. The results obtained from FT-IR and DSC confirmed that HCPT was molecularly dispersed in nanoparticles and no chemical reaction occurred. The size of the nanoparticles measured by DLS demonstrated that the size distribution was narrow and the average diameter was less than 200 nm. The morphology of the nanoparticles observed by TEM indicated that the nanoparticles exhibited a smooth surface and distinct spherical shape. In vitro release experiments indicated that the HCPT-loaded nanoparticles showed sustained release profiles. The results of a drug loading test revealed that adding TPGS could increase the drug loading. The drug loading of stabilized micelle structure nanoparticles with 70% of TPGS was about 0.0425+/-0.0011% w/w compared to 0.0254+/-0.0008% w/w found for the nanoparticles without TPGS. The results of CMC value tests showed that the CMC values of the stabilized nanoparticles were approximately 10-fold lower than those of the nonstabilized micelles (from 2.0x10(-5) to 2.5x10(-4) M). Cytotoxicity tests showed that the cytotoxicity of HCPT-loaded nanoparticles against cancer cells in vitro was remarkably higher than that of free drugs. 10-Hydroxycamptothecin-loaded nanoparticles may serve as a stable delivery system for poorly soluble HCPT.

  12. Toward N Criteria in Coastal Waters: Normalizing N Loading for Estuarine Volume and Local Residence Time

    EPA Science Inventory

    One approach to developing criteria for nitrogen (N) in coastal waters has been to determine quantitative relationships between N loading and ecological effects (e.g., hypoxia) in coastal estuaries. Although this approach has met with some success, data obtained from field sites ...

  13. Response of magnesium single crystals to shock-wave loading at normal and elevated temperatures

    NASA Astrophysics Data System (ADS)

    Garkushin, G.; Kanel, G.; Savinykh, A.; Razorenov, S.; Jones, D.; Proud, W.

    2013-06-01

    Magnesium single crystals, 0.2 mm to 3 mm thick, were shock loaded along the two axes, a, c and the direction at 45 degrees to the c-axis. At the room temperature the response is very similar to that observed by Pope and Johnson for beryllium single crystals (1974). Shock compression along the c-axis causes inelastic deformation by means of pyramidal slip and twinning and is associated with the largest HEL. The easiest basal slip was activated by shock loading along the inclined, off-axis direction and is associated with smallest HEL value. For all orientations, we observed elastic precursor decay and growth of the HEL values with increasing temperature. However, for the c-orientation the growth is caused by decrease of elastic constants and not with an increase of resolved shear stress along the pyramidal slip planes. In the other orientations the resolved shear stresses in slip planes at the HEL increased with temperature. At inclined shock compression we found two plastic shock waves for which the stress behind the first depends on the peak stress associated with the second plastic wave. The crystals demonstrate the largest spall strength at shock loading along the a-axis and smallest one at shock loading in off-axis direction.

  14. Use of self assembled monolayers at variable coverage to control interface bonding in a model study of interfacial fracture: Pure shear loading

    SciTech Connect

    KENT,MICHAEL S.; YIM,HYUN; MATHESON,AARON J.; COGDILL,C.; NELSON,GERALD C.; REEDY JR.,EARL DAVID

    2000-05-16

    The relationships between fundamental interfacial interactions, energy dissipation mechanisms, and fracture stress or fracture toughness in a glassy thermoset/inorganic solid joint are not well understood. This subject is addressed with a model system involving an epoxy adhesive on a polished silicon wafer containing its native oxide. The proportions of physical and chemical interactions at the interface, and the in-plane distribution, are varied using self-assembling monolayers of octadecyltrichlorosilane (ODTS). The epoxy interacts strongly with the bare silicon oxide surface, but forms only a very weak interface with the methylated tails of the ODTS monolayer. The fracture stress is examined as a function of ODTS coverage in the napkin-ring (pure shear) loading geometry. The relationship between fracture stress and ODTS coverage is catastrophic, with a large change in fracture stress occurring over a narrow range of ODTS coverage. This transition in fracture stress does not correspond to a wetting transition of the epoxy. Rather, the transition in fracture stress corresponds to the onset of deformation in the epoxy, or the transition from brittle to ductile fracture. The authors postulate that the transition in fracture stress occurs when the local stress that the interface can support becomes comparable to the yield stress of the epoxy. The fracture results are independent of whether the ODTS deposition occurs by island growth (T{sub dep} = 10 C) or by homogeneous growth (T{sub dep} = 24 C).

  15. Onset of failure in finitely strained layered composites subjected to combined normal and shear loading

    NASA Astrophysics Data System (ADS)

    Nestorović, M. D.; Triantafyllidis, N.

    2004-04-01

    A limiting factor in the design of fiber-reinforced composites is their failure under axial compression along the fiber direction. These critical axial stresses are significantly reduced in the presence of shear stresses. This investigation is motivated by the desire to study the onset of failure in fiber-reinforced composites under arbitrary multi-axial loading and in the absence of the experimentally inevitable imperfections and finite boundaries. By using a finite strain continuum mechanics formulation for the bifurcation (buckling) problem of a rate-independent, perfectly periodic (layered) solid of infinite extent, we are able to study the influence of load orientation, material properties and fiber volume fraction on the onset of instability in fiber-reinforced composites. Two applications of the general theory are presented in detail, one for a finitely strained elastic rubber composite and another for a graphite-epoxy composite, whose constitutive properties have been determined experimentally. For the latter case, extensive comparisons are made between the predictions of our general theory and the available experimental results as well as to the existing approximate structural theories. It is found that the load orientation, material properties and fiber volume fraction have substantial effects on the onset of failure stresses as well as on the type of the corresponding mode (local or global).

  16. Results of loading doses of aspartame by two phenylketonuric (PKU) children compared with two normal children.

    PubMed

    Koch, R; Schaeffler, G; Shaw, N F

    1976-11-01

    Separate tolerance tests with aspartame at 34 mg/kg-day and phenylalanine at 19 mg/kg-day were compared. The results reveal that slight serum elevation of phenylalanine and tyrosine occurred in the two PKU and the normal healthy adolescents. It would appear that the phenylalanine in the sweetener aspartame is small enough to be of little clinical significance.

  17. 46 CFR 112.35-3 - Normal source for emergency loads.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ....35-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Manually Controlled Emergency Systems Having a Storage Battery or a Diesel Engine or Gas Turbine Driven Generator as the Sole Emergency Power Source § 112.35-3 Normal...

  18. Load compensating reactions to perturbations at wrist joint in normal man

    NASA Technical Reports Server (NTRS)

    Jaeger, R. J.; Agarwell, G. C.; Gottlieb, G. L.

    1981-01-01

    The electromyographic responses to step torque loads were studied in flexors and extensors at the human wrist. Based on temporal bursting patterns and functional behavior, the response was divided into four temporal components. Two early components, the myotatic (30-60 ms) late myotatic (60-120 ms) appears to be reflex response. The third postmyotatic component (120-200 ms) appear to be a triggered reaction, preceeding the fourth, stabilizing component (200-400 ms). A comparison of response at the wrist with similar data at the ankle provides the basis for a generalized classification of the response in various muscles to torque step perturbations.

  19. Analysis of rabbit intervertebral disc physiology based on water metabolism. II. Changes in normal intervertebral discs under axial vibratory load

    SciTech Connect

    Hirano, N.; Tsuji, H.; Ohshima, H.; Kitano, S.; Itoh, T.; Sano, A.

    1988-11-01

    Metabolic changes induced by axial vibratory load to the spine were investigated based on water metabolism in normal intervertebral discs of rabbits with or without pentobarbital anesthesia. Tritiated water concentration in the intervertebral discs of unanesthetized rabbits was reduced remarkably by axial vibration for 30 minutes using the vibration machine developed for this study. Repeated vibratory load for 18 and 42 hours duration showed the recovery of /sup 3/H/sub 2/O concentration of the intervertebral disc without anesthesia. Computer simulation suggested a reduction of blood flow surrounding the intervertebral disc following the vibration stress. However, no reduction of the /sup 3/H/sub 2/O concentration in the intervertebral disc was noted under anesthesia. Emotional stress cannot be excluded as a factor in water metabolism in the intervertebral disc.

  20. Effect of aspartame and aspartate loading upon plasma and erythrocyte free amino acid levels in normal adult volunteers.

    PubMed

    Stegink, L D; Filer, L J; Baker, G L

    1977-10-01

    Aspartame is a dipeptide (L-aspartyl-L-phenylalanyl-methyl ester) with a sweeting potential 180 to 200 times that of sucrose. Questions have been raised about potential toxic effects of its constituent amino acids, aspartate and phenylalanine when the compound is ingested in large amounts. Plasma and erythrocyte amino acid levels were measured in 12 normal subjects after administration of either Aspartame (34 mg/kg) or equimolar quantities of aspartate (13 mg/kg) in a crossover design. No changes in either plasma or erythrocyte aspartate levels were noted at any time after either Aspartame or aspartate ingestion. Plasma phenylalanine levels decrease slightly after aspartate loading, and increased from fasting levels (4.9 +/- 1 mumoles/100 ml) to 10.7 +/- 1.9 mumoles/100 ml about 45 to 60 minutes after Aspartame loading. Phenylalanine levels returned to baseline by 4 hours. Erythrocyte phenylalanine levels showed similar changes.

  1. Effects of pleiotrophin overexpression on mouse skeletal muscles in normal loading and in actual and simulated microgravity.

    PubMed

    Camerino, Giulia Maria; Pierno, Sabata; Liantonio, Antonella; De Bellis, Michela; Cannone, Maria; Sblendorio, Valeriana; Conte, Elena; Mele, Antonietta; Tricarico, Domenico; Tavella, Sara; Ruggiu, Alessandra; Cancedda, Ranieri; Ohira, Yoshinobu; Danieli-Betto, Daniela; Ciciliot, Stefano; Germinario, Elena; Sandonà, Dorianna; Betto, Romeo; Camerino, Diana Conte; Desaphy, Jean-François

    2013-01-01

    Pleiotrophin (PTN) is a widespread cytokine involved in bone formation, neurite outgrowth, and angiogenesis. In skeletal muscle, PTN is upregulated during myogenesis, post-synaptic induction, and regeneration after crushing, but little is known regarding its effects on muscle function. Here, we describe the effects of PTN on the slow-twitch soleus and fast-twitch extensor digitorum longus (EDL) muscles in mice over-expressing PTN under the control of a bone promoter. The mice were maintained in normal loading or disuse condition, induced by hindlimb unloading (HU) for 14 days. Effects of exposition to near-zero gravity during a 3-months spaceflight (SF) into the Mice Drawer System are also reported. In normal loading, PTN overexpression had no effect on muscle fiber cross-sectional area, but shifted soleus muscle toward a slower phenotype, as shown by an increased number of oxidative type 1 fibers, and increased gene expression of cytochrome c oxidase subunit IV and citrate synthase. The cytokine increased soleus and EDL capillary-to-fiber ratio. PTN overexpression did not prevent soleus muscle atrophy, slow-to-fast transition, and capillary regression induced by SF and HU. Nevertheless, PTN exerted various effects on sarcolemma ion channel expression/function and resting cytosolic Ca(2+) concentration in soleus and EDL muscles, in normal loading and after HU. In conclusion, the results show very similar effects of HU and SF on mouse soleus muscle, including activation of specific gene programs. The EDL muscle is able to counterbalance this latter, probably by activating compensatory mechanisms. The numerous effects of PTN on muscle gene expression and functional parameters demonstrate the sensitivity of muscle fibers to the cytokine. Although little benefit was found in HU muscle disuse, PTN may emerge useful in various muscle diseases, because it exerts synergetic actions on muscle fibers and vessels, which could enforce oxidative metabolism and ameliorate muscle

  2. Coupled vibrations of rectangular buildings subjected to normally-incident random wind loads

    USGS Publications Warehouse

    Safak, E.; Foutch, D.A.

    1987-01-01

    A method for analyzing the three-directional coupled dynamic response of wind-excited buildings is presented. The method is based on a random vibration concept and is parallel to those currently used for analyzing alongwind response. Only the buildings with rectangular cross-section and normally-incident wind are considered. The alongwind pressures and their correlations are represented by the well-known expressions that are available in the literature. The acrosswind forces are assumed to be mainly due to vortex shedding. The torque acting on the building is taken as the sum of the torque due to random alongwind forces plus the torque due to asymmetric acrosswind forces. The study shows the following: (1) amplitude of acrosswind vibrations can be several times greater than that of alongwind vibrations; (2) torsional vibrations are significant if the building has large frontal width, and/or it is asymmetric, and/or its torsional natural frequency is low; (3) even a perfectly symmetric structure with normally incident wind can experience significant torsional vibrations due to the randomness of wind pressures. ?? 1987.

  3. PPARα Agonist Fenofibrate Reduced the Secreting Load of β-Cells in Hypertriglyceridemia Patients with Normal Glucose Tolerance.

    PubMed

    Liu, Jia; Lu, Rui; Wang, Ying; Hu, Yanjin; Jia, Yumei; Yang, Ning; Fu, Jing; Wang, Guang

    2016-01-01

    Hypertriglyceridemia is an important risk factor associated with insulin resistance and β-cell dysfunction. This study investigated the effects of hypertriglyceridemia and fenofibrate treatment on insulin sensitivity and β-cell function in subjects with normal glucose tolerance. A total of 1974 subjects with normal glucose tolerance were divided into the normal TG group (NTG group, n = 1302) and hypertriglyceridemia group (HTG group, n = 672). Next, 92 patients selected randomly from 672 patients with hypertriglyceridemia were assigned to a 24-week fenofibrate treatment. The HTG group had increased waist circumference (WC), body mass index (BMI), homeostasis model assessment of insulin resistance (HOMA-IR), and homeostasis model assessment of β-cell function (HOMA-β) and decreased high-density lipoprotein cholesterol (HDL-C) compared with the NTG group (all P < 0.01). The 24-week fenofibrate treatment significantly decreased the WC, BMI, TG, HOMA-IR, and HOMA-β levels and increased the HDL-C levels in the patients with hypertriglyceridemia (WC, BMI, and HOMA-IR: P < 0.05; TG, HDL-C, and HOMA-β: P < 0.01). The fenofibrate treatment significantly alleviated insulin resistance and reduced the secreting load of β-cells in the hypertriglyceridemia patients with normal glucose tolerance. PMID:27034649

  4. PPARα Agonist Fenofibrate Reduced the Secreting Load of β-Cells in Hypertriglyceridemia Patients with Normal Glucose Tolerance

    PubMed Central

    Liu, Jia; Lu, Rui; Wang, Ying; Hu, Yanjin; Jia, Yumei; Yang, Ning; Fu, Jing

    2016-01-01

    Hypertriglyceridemia is an important risk factor associated with insulin resistance and β-cell dysfunction. This study investigated the effects of hypertriglyceridemia and fenofibrate treatment on insulin sensitivity and β-cell function in subjects with normal glucose tolerance. A total of 1974 subjects with normal glucose tolerance were divided into the normal TG group (NTG group, n = 1302) and hypertriglyceridemia group (HTG group, n = 672). Next, 92 patients selected randomly from 672 patients with hypertriglyceridemia were assigned to a 24-week fenofibrate treatment. The HTG group had increased waist circumference (WC), body mass index (BMI), homeostasis model assessment of insulin resistance (HOMA-IR), and homeostasis model assessment of β-cell function (HOMA-β) and decreased high-density lipoprotein cholesterol (HDL-C) compared with the NTG group (all P < 0.01). The 24-week fenofibrate treatment significantly decreased the WC, BMI, TG, HOMA-IR, and HOMA-β levels and increased the HDL-C levels in the patients with hypertriglyceridemia (WC, BMI, and HOMA-IR: P < 0.05; TG, HDL-C, and HOMA-β: P < 0.01). The fenofibrate treatment significantly alleviated insulin resistance and reduced the secreting load of β-cells in the hypertriglyceridemia patients with normal glucose tolerance. PMID:27034649

  5. Normalized Diurnal and Between-Day Trends in Illicit and Legal Drug Loads that Account for Changes in Population

    PubMed Central

    Brewer, Alex J.; Ort, Christoph; Banta-Green, Caleb J.; Berset, Jean-Daniel

    2012-01-01

    Drug concentrations in composite municipal wastewater samples and census-based estimates of population are used to derive daily loads of illicit substances that are indexed to population. However, such estimates do not provide information on the diurnal trends of substance excretion nor can they account for changes in population. To address these limitations, a series of 1 h composites created by sampling wastewater influent at 6 min intervals was collected over four consecutive days at a single wastewater treatment plant. Creatinine (a urinary indicator), caffeine, methamphetamine, benzoylecgonine (BZE), and cocaine were analyzed by liquid chromatography/tandem mass spectrometry (LC-MS/MS). Diurnal trends and between-day trends were substance specific and related to the number of estimated doses and excretory half-life. Normalization to creatinine yielded trends in substances that differed significantly from non-normalized trends by accounting for changes in population within the municipality studied. Increases in normalized substance excretion observed during early morning hours originate from individuals among the resident population of the municipality due to the absence of commuters. PMID:22804833

  6. Pure-quartic solitons

    PubMed Central

    Blanco-Redondo, Andrea; Martijn, de Sterke C.; Sipe, J.E.; Krauss, Thomas F.; Eggleton, Benjamin J.; Husko, Chad

    2016-01-01

    Temporal optical solitons have been the subject of intense research due to their intriguing physics and applications in ultrafast optics and supercontinuum generation. Conventional bright optical solitons result from the interaction of anomalous group-velocity dispersion and self-phase modulation. Here we experimentally demonstrate a class of bright soliton arising purely from the interaction of negative fourth-order dispersion and self-phase modulation, which can occur even for normal group-velocity dispersion. We provide experimental and numerical evidence of shape-preserving propagation and flat temporal phase for the fundamental pure-quartic soliton and periodically modulated propagation for the higher-order pure-quartic solitons. We derive the approximate shape of the fundamental pure-quartic soliton and discover that is surprisingly Gaussian, exhibiting excellent agreement with our experimental observations. Our discovery, enabled by precise dispersion engineering, could find applications in communications, frequency combs and ultrafast lasers. PMID:26822758

  7. Pure-quartic solitons.

    PubMed

    Blanco-Redondo, Andrea; de Sterke, C Martijn; Martijn, de Sterke C; Sipe, J E; Krauss, Thomas F; Eggleton, Benjamin J; Husko, Chad

    2016-01-01

    Temporal optical solitons have been the subject of intense research due to their intriguing physics and applications in ultrafast optics and supercontinuum generation. Conventional bright optical solitons result from the interaction of anomalous group-velocity dispersion and self-phase modulation. Here we experimentally demonstrate a class of bright soliton arising purely from the interaction of negative fourth-order dispersion and self-phase modulation, which can occur even for normal group-velocity dispersion. We provide experimental and numerical evidence of shape-preserving propagation and flat temporal phase for the fundamental pure-quartic soliton and periodically modulated propagation for the higher-order pure-quartic solitons. We derive the approximate shape of the fundamental pure-quartic soliton and discover that is surprisingly Gaussian, exhibiting excellent agreement with our experimental observations. Our discovery, enabled by precise dispersion engineering, could find applications in communications, frequency combs and ultrafast lasers. PMID:26822758

  8. Exploring a semimechanistic episodic Langevin model for bed load transport: Emergence of normal and anomalous advection and diffusion regimes

    NASA Astrophysics Data System (ADS)

    Fan, Niannian; Singh, Arvind; Guala, Michele; Foufoula-Georgiou, Efi; Wu, Baosheng

    2016-04-01

    Bed load transport is a highly stochastic, multiscale process, where particle advection and diffusion regimes are governed by the dynamics of each sediment grain during its motion and resting states. Having a quantitative understanding of the macroscale behavior emerging from the microscale interactions is important for proper model selection in the absence of individual grain-scale observations. Here we develop a semimechanistic sediment transport model based on individual particle dynamics, which incorporates the episodic movement (steps separated by rests) of sediment particles and study their macroscale behavior. By incorporating different types of probability distribution functions (PDFs) of particle resting times Tr, under the assumption of thin-tailed PDF of particle velocities, we study the emergent behavior of particle advection and diffusion regimes across a wide range of spatial and temporal scales. For exponential PDFs of resting times Tr, we observe normal advection and diffusion at long time scales. For a power-law PDF of resting times (i.e., f>(Tr>)˜Tr-ν), the tail thickness parameter ν is observed to affect the advection regimes (both sub and normal advective), and the diffusion regimes (both subdiffusive and superdiffusive). By comparing our semimechanistic model with two random walk models in the literature, we further suggest that in order to reproduce accurately the emerging diffusive regimes, the resting time model has to be coupled with a particle motion model able to produce finite particle velocities during steps, as the episodic model discussed here.

  9. A piloted simulation investigation of the normal load factor and longitudinal thrust required for air-to-air acquisition and tracking

    NASA Technical Reports Server (NTRS)

    Whalley, Matthew S.

    1993-01-01

    A piloted simulation study was performed by the U.S. Army Aeroflighydynamics Directorate to develop insight into the maneuverability requirements for aggressive helicopter maneuvering tasks such as air-to-air combat. Both a conventional helicopter and a helicopter with auxiliary thrust were examined. The aircraft parameters of interest were the normal and longitudinal load factor envelopes. Of particular interest were the mission performance and handling qualities tradeoffs with the parameters of interest. Two air-to-air acquisition and tracking tasks and a return-to-cover task were performed to assess mission performance. Results indicate that without auxiliary thrust, the ownship normal load factor capability needs to match that of the adversary in order to provide satisfactory handling qualities. Auxiliary thrust provides significant handling qualities advantages and can be substituted to some extent for normal load factor capability. Auxiliary thrust levels as low as 0.2 thrust/weight can provide significant handling qualities advantages.

  10. Stiffness of sphere-plate contacts at MHz frequencies: dependence on normal load, oscillation amplitude, and ambient medium.

    PubMed

    Vlachová, Jana; König, Rebekka; Johannsmann, Diethelm

    2015-01-01

    The stiffness of micron-sized sphere-plate contacts was studied by employing high frequency, tangential excitation of variable amplitude (0-20 nm). The contacts were established between glass spheres and the surface of a quartz crystal microbalance (QCM), where the resonator surface had been coated with either sputtered SiO2 or a spin-cast layer of poly(methyl methacrylate) (PMMA). The results from experiments undertaken in the dry state and in water are compared. Building on the shifts in the resonance frequency and resonance bandwidth, the instrument determines the real and the imaginary part of the contact stiffness, where the imaginary part quantifies dissipative processes. The method is closely analogous to related procedures in AFM-based metrology. The real part of the contact stiffness as a function of normal load can be fitted with the Johnson-Kendall-Roberts (JKR) model. The contact stiffness was found to increase in the presence of liquid water. This finding is tentatively explained by the rocking motion of the spheres, which couples to a squeeze flow of the water close to the contact. The loss tangent of the contact stiffness is on the order of 0.1, where the energy losses are associated with interfacial processes. At high amplitudes partial slip was found to occur. The apparent contact stiffness at large amplitude depends linearly on the amplitude, as predicted by the Cattaneo-Mindlin model. This finding is remarkable insofar, as the Cattaneo-Mindlin model assumes Coulomb friction inside the sliding region. Coulomb friction is typically viewed as a macroscopic concept, related to surface roughness. An alternative model (formulated by Savkoor), which assumes a constant frictional stress in the sliding zone independent of the normal pressure, is inconsistent with the experimental data. The apparent friction coefficients slightly increase with normal force, which can be explained by nanoroughness. In other words, contact splitting (i.e., a transport of

  11. Attentional Distractor Interference May Be Diminished by Concurrent Working Memory Load in Normal Participants and Traumatic Brain Injury Patients

    ERIC Educational Resources Information Center

    de Liano, Beatriz Gil-Gomez; Umilta, Carlo; Stablum, Franca; Tebaldi, Francesca; Cantagallo, Anna

    2010-01-01

    A reduction in congruency effects under working memory (WM) load has been previously described using different attentional paradigms (e.g., Kim, Kim, & Chun, 2005; Smilek, Enns, Eastwood, & Merikle, 2006). One hypothesis is that different types of WM load have different effects on attentional selection, depending on whether a specific memory load…

  12. Spatial release of cognitive load measured in a dual-task paradigm in normal-hearing and hearing-impaired listeners.

    PubMed

    Xia, Jing; Nooraei, Nazanin; Kalluri, Sridhar; Edwards, Brent

    2015-04-01

    This study investigated whether spatial separation between talkers helps reduce cognitive processing load, and how hearing impairment interacts with the cognitive load of individuals listening in multi-talker environments. A dual-task paradigm was used in which performance on a secondary task (visual tracking) served as a measure of the cognitive load imposed by a speech recognition task. Visual tracking performance was measured under four conditions in which the target and the interferers were distinguished by (1) gender and spatial location, (2) gender only, (3) spatial location only, and (4) neither gender nor spatial location. Results showed that when gender cues were available, a 15° spatial separation between talkers reduced the cognitive load of listening even though it did not provide further improvement in speech recognition (Experiment I). Compared to normal-hearing listeners, large individual variability in spatial release of cognitive load was observed among hearing-impaired listeners. Cognitive load was lower when talkers were spatially separated by 60° than when talkers were of different genders, even though speech recognition was comparable in these two conditions (Experiment II). These results suggest that a measure of cognitive load might provide valuable insight into the benefit of spatial cues in multi-talker environments. PMID:25920841

  13. Tailoring the Blast Exposure Conditions in the Shock Tube for Generating Pure, Primary Shock Waves: The End Plate Facilitates Elimination of Secondary Loading of the Specimen.

    PubMed

    Kuriakose, Matthew; Skotak, Maciej; Misistia, Anthony; Kahali, Sudeepto; Sundaramurthy, Aravind; Chandra, Namas

    2016-01-01

    The end plate mounted at the mouth of the shock tube is a versatile and effective implement to control and mitigate the end effects. We have performed a series of measurements of incident shock wave velocities and overpressures followed by quantification of impulse values (integral of pressure in time domain) for four different end plate configurations (0.625, 2, 4 inches, and an open end). Shock wave characteristics were monitored by high response rate pressure sensors allocated in six positions along the length of 6 meters long 229 mm square cross section shock tube. Tests were performed at three shock wave intensities, which was controlled by varying the Mylar membrane thickness (0.02, 0.04 and 0.06 inch). The end reflector plate installed at the exit of the shock tube allows precise control over the intensity of reflected waves penetrating into the shock tube. At the optimized distance of the tube to end plate gap the secondary waves were entirely eliminated from the test section, which was confirmed by pressure sensor at T4 location. This is pronounced finding for implementation of pure primary blast wave animal model. These data also suggest only deep in the shock tube experimental conditions allow exposure to a single shock wave free of artifacts. Our results provide detailed insight into spatiotemporal dynamics of shock waves with Friedlander waveform generated using helium as a driver gas and propagating in the air inside medium sized tube. Diffusion of driver gas (helium) inside the shock tube was responsible for velocity increase of reflected shock waves. Numerical simulations combined with experimental data suggest the shock wave attenuation mechanism is simply the expansion of the internal pressure. In the absence of any other postulated shock wave decay mechanisms, which were not implemented in the model the agreement between theory and experimental data is excellent. PMID:27603017

  14. Tailoring the Blast Exposure Conditions in the Shock Tube for Generating Pure, Primary Shock Waves: The End Plate Facilitates Elimination of Secondary Loading of the Specimen

    PubMed Central

    Misistia, Anthony; Kahali, Sudeepto; Sundaramurthy, Aravind; Chandra, Namas

    2016-01-01

    The end plate mounted at the mouth of the shock tube is a versatile and effective implement to control and mitigate the end effects. We have performed a series of measurements of incident shock wave velocities and overpressures followed by quantification of impulse values (integral of pressure in time domain) for four different end plate configurations (0.625, 2, 4 inches, and an open end). Shock wave characteristics were monitored by high response rate pressure sensors allocated in six positions along the length of 6 meters long 229 mm square cross section shock tube. Tests were performed at three shock wave intensities, which was controlled by varying the Mylar membrane thickness (0.02, 0.04 and 0.06 inch). The end reflector plate installed at the exit of the shock tube allows precise control over the intensity of reflected waves penetrating into the shock tube. At the optimized distance of the tube to end plate gap the secondary waves were entirely eliminated from the test section, which was confirmed by pressure sensor at T4 location. This is pronounced finding for implementation of pure primary blast wave animal model. These data also suggest only deep in the shock tube experimental conditions allow exposure to a single shock wave free of artifacts. Our results provide detailed insight into spatiotemporal dynamics of shock waves with Friedlander waveform generated using helium as a driver gas and propagating in the air inside medium sized tube. Diffusion of driver gas (helium) inside the shock tube was responsible for velocity increase of reflected shock waves. Numerical simulations combined with experimental data suggest the shock wave attenuation mechanism is simply the expansion of the internal pressure. In the absence of any other postulated shock wave decay mechanisms, which were not implemented in the model the agreement between theory and experimental data is excellent. PMID:27603017

  15. Tailoring the Blast Exposure Conditions in the Shock Tube for Generating Pure, Primary Shock Waves: The End Plate Facilitates Elimination of Secondary Loading of the Specimen.

    PubMed

    Kuriakose, Matthew; Skotak, Maciej; Misistia, Anthony; Kahali, Sudeepto; Sundaramurthy, Aravind; Chandra, Namas

    2016-01-01

    The end plate mounted at the mouth of the shock tube is a versatile and effective implement to control and mitigate the end effects. We have performed a series of measurements of incident shock wave velocities and overpressures followed by quantification of impulse values (integral of pressure in time domain) for four different end plate configurations (0.625, 2, 4 inches, and an open end). Shock wave characteristics were monitored by high response rate pressure sensors allocated in six positions along the length of 6 meters long 229 mm square cross section shock tube. Tests were performed at three shock wave intensities, which was controlled by varying the Mylar membrane thickness (0.02, 0.04 and 0.06 inch). The end reflector plate installed at the exit of the shock tube allows precise control over the intensity of reflected waves penetrating into the shock tube. At the optimized distance of the tube to end plate gap the secondary waves were entirely eliminated from the test section, which was confirmed by pressure sensor at T4 location. This is pronounced finding for implementation of pure primary blast wave animal model. These data also suggest only deep in the shock tube experimental conditions allow exposure to a single shock wave free of artifacts. Our results provide detailed insight into spatiotemporal dynamics of shock waves with Friedlander waveform generated using helium as a driver gas and propagating in the air inside medium sized tube. Diffusion of driver gas (helium) inside the shock tube was responsible for velocity increase of reflected shock waves. Numerical simulations combined with experimental data suggest the shock wave attenuation mechanism is simply the expansion of the internal pressure. In the absence of any other postulated shock wave decay mechanisms, which were not implemented in the model the agreement between theory and experimental data is excellent.

  16. Failure behavior of plasma-sprayed HAp coating on commercially pure titanium substrate in simulated body fluid (SBF) under bending load.

    PubMed

    Laonapakul, Teerawat; Rakngarm Nimkerdphol, Achariya; Otsuka, Yuichi; Mutoh, Yoshiharu

    2012-11-01

    Four point bending tests with acoustic emission (AE) monitoring were conducted for evaluating failure behavior of the plasma-sprayed hydroxyapatite (HAp) top coat on commercially pure titanium (cp-Ti) plate with and without mixed HAp/Ti bond coat. Effect of immersion in simulated body fluid (SBF) on failure behavior of the coated specimen was also investigated by immersing the specimen in SBF. The AE patterns obtained from the bending test of the HAp coating specimens after a week immersion in SBF clearly showed the earlier stage of delamination and spallation of the coating layer compared to those without immersion in SBF. It was also found that the bond coating improved failure resistance of the HAp coating specimen compared to that without the bond coat. Four point bend fatigue tests under ambient and SBF environments were also conducted with AE monitoring during the entire fatigue test for investigating the influence of SBF environment on fatigue failure behavior of the HAp coating specimen with the mixed HAp/Ti bond coat. The specimens tested at a stress amplitude of 120 MPa under both ambient and SBF environments could survive up to 10⁷ cycles without spallation of HAp coating layer. The specimens tested under SBF environment and those tested under ambient environment after immersion in SBF showed shorter fatigue life compared to those tested under ambient environment without SBF immersion. Micro-cracks nucleated in the coating layer in the early stage of fatigue life and then propagated into the cp-Ti substrate in the intermediate stage, which unstably propagated to failure in the final stage. It was found from the XRD analysis that the dissolution of the co-existing phases and the precipitation of the HAp phase were taken place during immersion in SBF. During this process, the co-existing phases disappeared from the coating layer and the HAp phase fully occupied the coating layer. The degradation of bending strength and fatigue life of the HAp coating

  17. When Breathing Interferes with Cognition: Experimental Inspiratory Loading Alters Timed Up-and-Go Test in Normal Humans.

    PubMed

    Nierat, Marie-Cécile; Demiri, Suela; Dupuis-Lozeron, Elise; Allali, Gilles; Morélot-Panzini, Capucine; Similowski, Thomas; Adler, Dan

    2016-01-01

    Human breathing stems from automatic brainstem neural processes. It can also be operated by cortico-subcortical networks, especially when breathing becomes uncomfortable because of external or internal inspiratory loads. How the "irruption of breathing into consciousness" interacts with cognition remains unclear, but a case report in a patient with defective automatic breathing (Ondine's curse syndrome) has shown that there was a cognitive cost of breathing when the respiratory cortical networks were engaged. In a pilot study of putative breathing-cognition interactions, the present study relied on a randomized design to test the hypothesis that experimentally loaded breathing in 28 young healthy subjects would have a negative impact on cognition as tested by "timed up-and-go" test (TUG) and its imagery version (iTUG). Progressive inspiratory threshold loading resulted in slower TUG and iTUG performance. Participants consistently imagined themselves faster than they actually were. However, progressive inspiratory loading slowed iTUG more than TUG, a finding that is unexpected with regard to the known effects of dual tasking on TUG and iTUG (slower TUG but stable iTUG). Insofar as the cortical networks engaged in response to inspiratory loading are also activated during complex locomotor tasks requiring cognitive inputs, we infer that competition for cortical resources may account for the breathing-cognition interference that is evidenced here.

  18. When Breathing Interferes with Cognition: Experimental Inspiratory Loading Alters Timed Up-and-Go Test in Normal Humans

    PubMed Central

    Nierat, Marie-Cécile; Demiri, Suela; Dupuis-Lozeron, Elise; Allali, Gilles; Morélot-Panzini, Capucine; Similowski, Thomas; Adler, Dan

    2016-01-01

    Human breathing stems from automatic brainstem neural processes. It can also be operated by cortico-subcortical networks, especially when breathing becomes uncomfortable because of external or internal inspiratory loads. How the “irruption of breathing into consciousness” interacts with cognition remains unclear, but a case report in a patient with defective automatic breathing (Ondine's curse syndrome) has shown that there was a cognitive cost of breathing when the respiratory cortical networks were engaged. In a pilot study of putative breathing-cognition interactions, the present study relied on a randomized design to test the hypothesis that experimentally loaded breathing in 28 young healthy subjects would have a negative impact on cognition as tested by “timed up-and-go” test (TUG) and its imagery version (iTUG). Progressive inspiratory threshold loading resulted in slower TUG and iTUG performance. Participants consistently imagined themselves faster than they actually were. However, progressive inspiratory loading slowed iTUG more than TUG, a finding that is unexpected with regard to the known effects of dual tasking on TUG and iTUG (slower TUG but stable iTUG). Insofar as the cortical networks engaged in response to inspiratory loading are also activated during complex locomotor tasks requiring cognitive inputs, we infer that competition for cortical resources may account for the breathing-cognition interference that is evidenced here. PMID:26978782

  19. When Breathing Interferes with Cognition: Experimental Inspiratory Loading Alters Timed Up-and-Go Test in Normal Humans.

    PubMed

    Nierat, Marie-Cécile; Demiri, Suela; Dupuis-Lozeron, Elise; Allali, Gilles; Morélot-Panzini, Capucine; Similowski, Thomas; Adler, Dan

    2016-01-01

    Human breathing stems from automatic brainstem neural processes. It can also be operated by cortico-subcortical networks, especially when breathing becomes uncomfortable because of external or internal inspiratory loads. How the "irruption of breathing into consciousness" interacts with cognition remains unclear, but a case report in a patient with defective automatic breathing (Ondine's curse syndrome) has shown that there was a cognitive cost of breathing when the respiratory cortical networks were engaged. In a pilot study of putative breathing-cognition interactions, the present study relied on a randomized design to test the hypothesis that experimentally loaded breathing in 28 young healthy subjects would have a negative impact on cognition as tested by "timed up-and-go" test (TUG) and its imagery version (iTUG). Progressive inspiratory threshold loading resulted in slower TUG and iTUG performance. Participants consistently imagined themselves faster than they actually were. However, progressive inspiratory loading slowed iTUG more than TUG, a finding that is unexpected with regard to the known effects of dual tasking on TUG and iTUG (slower TUG but stable iTUG). Insofar as the cortical networks engaged in response to inspiratory loading are also activated during complex locomotor tasks requiring cognitive inputs, we infer that competition for cortical resources may account for the breathing-cognition interference that is evidenced here. PMID:26978782

  20. Repetitive transcranial magnetic stimulation over the supplementary motor area modifies breathing pattern in response to inspiratory loading in normal humans

    PubMed Central

    Nierat, Marie-Cécile; Hudson, Anna L.; Chaskalovic, Joël; Similowski, Thomas; Laviolette, Louis

    2015-01-01

    In awake humans, breathing depends on automatic brainstem pattern generators. It is also heavily influenced by cortical networks. For example, functional magnetic resonance imaging and electroencephalographic data show that the supplementary motor area becomes active when breathing is made difficult by inspiratory mechanical loads like resistances or threshold valves, which is associated with perceived respiratory discomfort. We hypothesized that manipulating the excitability of the supplementary motor area with repetitive transcranial magnetic stimulation would modify the breathing pattern response to an experimental inspiratory load and possibly respiratory discomfort. Seven subjects (three men, age 25 ± 4) were studied. Breathing pattern and respiratory discomfort during inspiratory loading were described before and after conditioning the supplementary motor area with repetitive stimulation, using an excitatory paradigm (5 Hz stimulation), an inhibitory paradigm, or sham stimulation. No significant change in breathing pattern during loading was observed after sham conditioning. Excitatory conditioning shortened inspiratory time (p = 0.001), decreased tidal volume (p = 0.016), and decreased ventilation (p = 0.003), as corroborated by an increased end-tidal expired carbon dioxide (p = 0.013). Inhibitory conditioning did not affect ventilation, but lengthened expiratory time (p = 0.031). Respiratory discomfort was mild under baseline conditions, and unchanged after conditioning of the supplementary motor area. This is the first study to show that repetitive transcranial magnetic stimulation conditioning of the cerebral cortex can alter breathing pattern. A 5 Hz conditioning protocol, known to enhance corticophrenic excitability, can reduce the amount of hyperventilation induced by inspiratory threshold loading. Further studies are needed to determine whether and under what circumstances rTMS can have an effect on dyspnoea. PMID:26483701

  1. The effect of laser activation of 5,10,15,20-tetra-sulphophenyl-porphyrin loaded in K562 cells and human normal mononuclear cells.

    PubMed

    Constantin, Carolina; Neagu, Monica; Manda, Gina; Ion, Rodica-Mariana; Iordăchescu, Dana Iord

    2004-01-01

    Photodynamic therapy (PDT) is a relatively new type of treatment in cancer, based on a photosensitizer, visible light and molecular oxygen. Reactive oxygen species are generated, causing tumor cells death by apoptosis or necrosis. Significant nowadays research efforts are focused on finding new photosensitizers with antineoplastic activity and an acceptable toxicological profile. Although consistent information exists regarding PDT in solid tumors, relatively few data are available for PDT of blood cancers. Therefore, we carried out a comparative study on lymphoblastic K562 cells and human normal peripheral blood mononuclear cells (PBMC) treated at a density of 2 x 10(5) cells/mL with 5,10,15,20-tetra-sulphophenyl-porphyrin (TSPP) and then irradiated with He-Ne laser light (lamda = 632.8 nm). The following cell functions were investigated: viability, multiplication, RNA synthesis, total RNA levels and apoptosis. After irradiation, the viability of TSPP-loaded tumor cells decrease, the multiplication rate and the total RNA level are drastically reduced and cells undergo apoptosis. TSPP alone loaded into cells but not activated by irradiation, does not affect these cell parameters. Human normal PBMC subjected to TSPP loading and laser-irradiation develop a different cellular response, their viability and proliferative capacity not being altered by experimental PDT. Accordingly, it appears that TSPP is a non-aggressive compound for cellular physiology and becomes cytotoxic only by irradiation; moreover laser-activated TSPP affects only cells that have a tumoral pattern.

  2. Short-Term Retention in Normal and Retarded Children as a Function of Memory Load and List Structure.

    ERIC Educational Resources Information Center

    Calfee, Robert C.

    Studies of recall and recognition short-term memory (STM) were reviewed, and a series of studies of serial recognition memory of normal and retarded children was described. In experiments using a recall procedure there were decrements in initial performance level with decreasing age and IQ but less evidence that forgetting occurred at a faster…

  3. Using direct normal irradiance models and utility electrical loading to assess benefit of a concentrating solar power plant

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Direct normal irradiance (DNI) is required to evaluate performance of concentrating solar energy systems. The objective of this paper is to analyze the effect of time interval (e.g. year, month, hour) on the accuracy of three different DNI models. The DNI data were measured at three different labora...

  4. Tantalum and vanadium response to shock-wave loading at normal and elevated temperatures. Non-monotonous decay of the elastic wave in vanadium

    SciTech Connect

    Zaretsky, E. B.; Kanel, G. I.

    2014-06-28

    The evolution of the elastic precursor waves in pure tantalum and vanadium is presented at normal and elevated temperatures over propagation distances that ranged from 0.125 to 3 mm. Measurements were performed in order to obtain experimental data about the temperature-rate dependence of the yield stress of the two metals. With increasing propagation distance, the rate of the decay of elastic precursor decreases, as the shear stress in the elastic precursor wave approaches the Peierls stresses. It has been found that the decay, with propagation distance, of the post-spike minimum of the spike-like elastic precursor wave in vanadium is essentially non-monotonous. The experiments also revealed that annealing of tantalum and vanadium increases their Hugoniot elastic limit. The anomalous increase of the high strain rate yield stress with temperature, as observed earlier for some FCC and HCP metals, has not been detected in these measurements.

  5. Viscosity of pure hydrocarbons

    SciTech Connect

    Knapstad, B.; Skjolsvik, P.A.; Oye, H.A.

    1989-01-01

    Accurate viscosity measurements have been performed on eight pure hydrocarbons at atmospheric pressure in the temperature range 20-150/sup 0/C, or up to approximately 20/sup 0/C below the boiling point of the hydrocarbon, by use of an absolute oscillating viscometer. The hydrocarbons are cyclohexane and benzene and the n-alkanes of hexane, heptane, octane, decane, dodecane, and tetradecane. The viscosities are described with a modified Arrhenius equation, and the deviation in fit is 0.12% or less. The accuracy is estimated to be 0.33-0.56%. The lowest viscosities are assumed to have the highest deviation. Literature data reported by Dymond and Young normally fit our viscosities within our estimated accuracy. Other literature viscosities tend to be higher than our results, especially for the n-alkanes.

  6. Effects of normal and abnormal loading conditions on morphogenesis of the prenatal hip joint: application to hip dysplasia

    PubMed Central

    Giorgi, Mario; Carriero, Alessandra; Shefelbine, Sandra J.; Nowlan, Niamh C.

    2015-01-01

    Joint morphogenesis is an important phase of prenatal joint development during which the opposing cartilaginous rudiments acquire their reciprocal and interlocking shapes. At an early stage of development, the prenatal hip joint is formed of a deep acetabular cavity that almost totally encloses the head. By the time of birth, the acetabulum has become shallower and the femoral head has lost substantial sphericity, reducing joint coverage and stability. In this study, we use a dynamic mechanobiological simulation to explore the effects of normal (symmetric), reduced and abnormal (asymmetric) prenatal movements on hip joint shape, to understand their importance for postnatal skeletal malformations such as developmental dysplasia of the hip (DDH). We successfully predict the physiological trends of decreasing sphericity and acetabular coverage of the femoral head during fetal development. We show that a full range of symmetric movements helps to maintain some of the acetabular depth and femoral head sphericity, while reduced or absent movements can lead to decreased sphericity and acetabular coverage of the femoral head. When an abnormal movement pattern was applied, a deformed joint shape was predicted, with an opened asymmetric acetabulum and the onset of a malformed femoral head. This study provides evidence for the importance of fetal movements in the prevention and manifestation of congenital musculoskeletal disorders such as DDH. PMID:26163754

  7. Effects of normal and abnormal loading conditions on morphogenesis of the prenatal hip joint: application to hip dysplasia.

    PubMed

    Giorgi, Mario; Carriero, Alessandra; Shefelbine, Sandra J; Nowlan, Niamh C

    2015-09-18

    Joint morphogenesis is an important phase of prenatal joint development during which the opposing cartilaginous rudiments acquire their reciprocal and interlocking shapes. At an early stage of development, the prenatal hip joint is formed of a deep acetabular cavity that almost totally encloses the head. By the time of birth, the acetabulum has become shallower and the femoral head has lost substantial sphericity, reducing joint coverage and stability. In this study, we use a dynamic mechanobiological simulation to explore the effects of normal (symmetric), reduced and abnormal (asymmetric) prenatal movements on hip joint shape, to understand their importance for postnatal skeletal malformations such as developmental dysplasia of the hip (DDH). We successfully predict the physiological trends of decreasing sphericity and acetabular coverage of the femoral head during fetal development. We show that a full range of symmetric movements helps to maintain some of the acetabular depth and femoral head sphericity, while reduced or absent movements can lead to decreased sphericity and acetabular coverage of the femoral head. When an abnormal movement pattern was applied, a deformed joint shape was predicted, with an opened asymmetric acetabulum and the onset of a malformed femoral head. This study provides evidence for the importance of fetal movements in the prevention and manifestation of congenital musculoskeletal disorders such as DDH. PMID:26163754

  8. Effects of normal and abnormal loading conditions on morphogenesis of the prenatal hip joint: application to hip dysplasia.

    PubMed

    Giorgi, Mario; Carriero, Alessandra; Shefelbine, Sandra J; Nowlan, Niamh C

    2015-09-18

    Joint morphogenesis is an important phase of prenatal joint development during which the opposing cartilaginous rudiments acquire their reciprocal and interlocking shapes. At an early stage of development, the prenatal hip joint is formed of a deep acetabular cavity that almost totally encloses the head. By the time of birth, the acetabulum has become shallower and the femoral head has lost substantial sphericity, reducing joint coverage and stability. In this study, we use a dynamic mechanobiological simulation to explore the effects of normal (symmetric), reduced and abnormal (asymmetric) prenatal movements on hip joint shape, to understand their importance for postnatal skeletal malformations such as developmental dysplasia of the hip (DDH). We successfully predict the physiological trends of decreasing sphericity and acetabular coverage of the femoral head during fetal development. We show that a full range of symmetric movements helps to maintain some of the acetabular depth and femoral head sphericity, while reduced or absent movements can lead to decreased sphericity and acetabular coverage of the femoral head. When an abnormal movement pattern was applied, a deformed joint shape was predicted, with an opened asymmetric acetabulum and the onset of a malformed femoral head. This study provides evidence for the importance of fetal movements in the prevention and manifestation of congenital musculoskeletal disorders such as DDH.

  9. Intravenous L-5-hydroxytryptophan in normal subjects: an interdisciplinary precursor loading study. Part 1: Implications of reproducible mood elevation.

    PubMed

    Pühringer, W; Wirz-Justice, A; Graw, P; Lacoste, V; Gastpar, M

    1976-11-01

    L-5-hydroxytryptophan ethylester (Ro 3-5940), a new soluble form of this serotonin precursor, was administered to 26 healthy, non-depressed subjects after premedication with the peripheral decarboxylase inhibitor benserazide (Ro 4-6402) in a total of 51 infusions. Those conditions were chosen for the main trial which in a pre-trial investigation had proved to combine minimal side effects with clear central effects in particular the observed marked mood elevation after 1-5HTP. Using these standardized conditions of application, an interindividually similar pattern of the time course of substance effects could be shown, and convincing evidence was deducible for an objective mood elevating effect of 1-5HTP infusion. Amongst the most impressive results was the parallelity of the time course of mood changes and concomitant changes in serum growth hormone levels. Especially emphasized are the important questions of effectivity, specificity and clinical practicability or safety, which are essential for any precursor study. Arguments are presented supporting the assumption that primarily serotoninergic changes underlie these mood effects. In our opinion this mode of i.v. application of 1-5HTP represents a practicable strategy for investigating biochemical hypotheses as to serotonin mediated normal and deviant human behaviour, especially in affective disorders.

  10. Used Nuclear Fuel Loading and Structural Performance Under Normal Conditions of Transport - Modeling, Simulation and Experimental Integration RD&D Plan

    SciTech Connect

    Adkins, Harold E.

    2013-04-01

    Under current U.S. Nuclear Regulatory Commission regulation, it is not sufficient for used nuclear fuel (UNF) to simply maintain its integrity during the storage period, it must maintain its integrity in such a way that it can withstand the physical forces of handling and transportation associated with restaging the fuel and moving it to treatment or recycling facilities, or a geologic repository. Hence it is necessary to understand the performance characteristics of aged UNF cladding and ancillary components under loadings stemming from transport initiatives. Researchers would like to demonstrate that enough information, including experimental support and modeling and simulation capabilities, exists to establish a preliminary determination of UNF structural performance under normal conditions of transport (NCT). This research, development and demonstration (RD&D) plan describes a methodology, including development and use of analytical models, to evaluate loading and associated mechanical responses of UNF rods and key structural components. This methodology will be used to provide a preliminary assessment of the performance characteristics of UNF cladding and ancillary components under rail-related NCT loading. The methodology couples modeling and simulation and experimental efforts currently under way within the Used Fuel Disposition Campaign (UFDC). The methodology will involve limited uncertainty quantification in the form of sensitivity evaluations focused around available fuel and ancillary fuel structure properties exclusively. The work includes collecting information via literature review, soliciting input/guidance from subject matter experts, performing computational analyses, planning experimental measurement and possible execution (depending on timing), and preparing a variety of supporting documents that will feed into and provide the basis for future initiatives. The methodology demonstration will focus on structural performance evaluation of

  11. Twisted partially pure spinors

    NASA Astrophysics Data System (ADS)

    Herrera, Rafael; Tellez, Ivan

    2016-08-01

    Motivated by the relationship between orthogonal complex structures and pure spinors, we define twisted partially pure spinors in order to characterize spinorially subspaces of Euclidean space endowed with a complex structure.

  12. Dynamic Crush Behaviors Of Aluminum Honeycomb Specimens Under Compression Dominant Inclined Loads

    SciTech Connect

    Hong, Sung-tae; Pan, Jwo; Tyan, Tau; Prasad, Priya

    2008-01-01

    The quasi-static and dynamic crush behaviors of aluminum 5052-H38 honeycomb specimens under out-of-plane inclined loads are investigated by experiments. Different types of honeycomb specimens were designed for crush tests under pure compressive and inclined loads with respect to the out-of-plane direction. A test fixture was designed for both quasi-static and dynamic crush tests under inclined loads. The results of the quasi-static crush tests indicate that the normal crush and shear strengths under inclined loads are consistent with the corresponding results under combined loads. The results of the dynamic crush tests indicate that as the impact velocity increases, the normal crush strength increases and the shear strength remains nearly the same. The trends of the normalized normal crush strengths under inclined loads for specimens with different in-plane orientation angles as functions of the impact velocity are very similar to each other. Based on the experimental results, a macroscopic yield criterion as a function of the impact velocity is proposed. The experimental results suggest that as the impact velocity increases, the shape of the macroscopic yield surface changes, or more specifically, the curvature of the yield surface increases near the pure compression state. The experimental results also show similar microscopic progressive folding mechanisms in honeycomb specimens under pure compressive and inclined loads. However, honeycomb specimens under inclined loads show inclined stacking patterns of folds due to the asymmetric location of horizontal plastic hinge lines.

  13. Teaching normal birth, normally.

    PubMed

    Hotelling, Barbara A

    2009-01-01

    Teaching normal-birth Lamaze classes normally involves considering the qualities that make birth normal and structuring classes to embrace those qualities. In this column, teaching strategies are suggested for classes that unfold naturally, free from unnecessary interventions. PMID:19436595

  14. Purely lytic osteosarcoma

    SciTech Connect

    De Santos, L.A.; Eideken, B.

    1982-11-01

    The radiographic features of 42 purely lytic osteosarcomas are presented. Purely lytic osteosarcoma is identified as a lytic lesion of bone with no demonstrable osteoid matrix by conventional radiographic modalities. Purely lytic osteosarcoma represented 13.7% of a group of 305 osteosarcomas. The most common presentation was that of a lytic illdefined lesion with a moderate to large extraosseous mass component. Nine lesions presented with benign radiographic features. The differential diagnosis is outlined. The need for awareness of this type of presentation of osteosarcoma is stressed.

  15. Geomorphology: Pure and applied

    SciTech Connect

    Hart, M.G.

    1986-01-01

    The book summarizes the history of intellectual debate in geomorphology and describes modern developments both ''pure'' and ''applied.'' The history begins well before W.M. Davis and follows through to such debates as those concerned with the Pleistocene. Modern developments in pure geomorphology are cast in terms of chapters on form, process, materials, and methods analysis. The applied chapters concentrate on environmental hazards and resources, and their management.

  16. Pure shift NMR.

    PubMed

    Zangger, Klaus

    2015-04-01

    Although scalar-coupling provides important structural information, the resulting signal splittings significantly reduce the resolution of NMR spectra. Limited resolution is a particular problem in proton NMR experiments, resulting in part from the limited proton chemical shift range (∼10 ppm) but even more from the splittings due to scalar coupling to nearby protons. "Pure shift" NMR spectroscopy (also known as broadband homonuclear decoupling) has been developed for disentangling overlapped proton NMR spectra. The resulting spectra are considerably simplified as they consist of single lines, reminiscent of proton-decoupled C-13 spectra at natural abundance, with no multiplet structure. The different approaches to obtaining pure shift spectra are reviewed here and several applications presented. Pure shift spectra are especially useful for highly overlapped proton spectra, as found for example in reaction mixtures, natural products and biomacromolecules.

  17. Production of pure metals

    NASA Technical Reports Server (NTRS)

    Philipp, W. H.; Marsik, S. J.; May, C. E. (Inventor)

    1974-01-01

    A process for depositing elements by irradiating liquids is reported. Ultra pure elements are precipitated from aqueous solutions or suspensions of compounds. A solution of a salt of a metal to be prepared is irradiated, and the insoluble reaction product settles out. Some chemical compounds may also be prepared in this manner.

  18. Dahlbeck and Pure Ontology

    ERIC Educational Resources Information Center

    Mackenzie, Jim

    2016-01-01

    This article responds to Johan Dahlbeck's "Towards a pure ontology: Children's bodies and morality" ["Educational Philosophy and Theory," vol. 46 (1), 2014, pp. 8-23 (EJ1026561)]. His arguments from Nietzsche and Spinoza do not carry the weight he supposes, and the conclusions he draws from them about pedagogy would be…

  19. Deviation from Normal Boltzmann Distribution of High-lying Energy Levels of Iron Atom Excited by Okamoto-cavity Microwave-induced Plasmas Using Pure Nitrogen and Nitrogen-Oxygen Gases.

    PubMed

    Wagatsuma, Kazuaki

    2015-01-01

    This paper describes several interesting excitation phenomena occurring in a microwave-induced plasma (MIP) excited with Okamoto-cavity, especially when a small amount of oxygen was mixed with nitrogen matrix in the composition of the plasma gas. An ion-to-atom ratio of iron, which was estimated from the intensity ratio of ion to atomic lines having almost the same excitation energy, was reduced by adding oxygen gas to the nitrogen MIP, eventually contributing to an enhancement in the emission intensities of the atomic lines. Furthermore, Boltzmann plots for iron atomic lines were observed in a wide range of the excitation energy from 3.4 to 6.9 eV, indicating that plots of the atomic lines having lower excitation energies (3.4 to 4.8 eV) were well fitted on a straight line while those having more than 5.5 eV deviated upwards from the linear relationship. This overpopulation would result from any other excitation process in addition to the thermal excitation that principally determines the Boltzmann distribution. A Penning-type collision with excited species of nitrogen molecules probably explains this additional excitation mechanism, in which the resulting iron ions recombine with captured electrons, followed by cascade de-excitations between closely-spaced excited levels just below the ionization limit. As a result, these high-lying levels might be more populated than the low-lying levels of iron atom. The ionization of iron would be caused less actively in the nitrogen-oxygen plasma than in a pure nitrogen plasma, because excited species of nitrogen molecule, which can provide the ionization energy in a collision with iron atom, are consumed through collisions with oxygen molecules to cause their dissociation. It was also observed that the overpopulation occurred to a lesser extent when oxygen gas was added to the nitrogen plasma. The reason for this was also attributed to decreased number density of the excited nitrogen species due to collisions with oxygen

  20. Evaluation of the effects of 80% methanolic leaf extract of Caylusea abyssinica (fresen.) fisch. & Mey. on glucose handling in normal, glucose loaded and diabetic rodents

    PubMed Central

    2012-01-01

    Background The leaves of Caylusea abyssinica (fresen.) Fisch. & Mey. (Resedaceae), a plant widely distributed in East African countries, have been used for management of diabetes mellitus in Ethiopian folklore medicine. However, its use has not been scientifically validated. The present study was undertaken to investigate antidiabetic effects of the hydroalcoholic leaf extract of C. abyssinica extract in rodents. Materials and method Male Animals were randomly divided into five groups for each diabetic, normoglycemic and oral glucose tolerance test (OGTT) studies. Group 1 served as controls and administered 2% Tween-80 in distilled water, (TW80); Group 2 received 5 mg/kg glibenclamide (GL5); Groups 3, 4 and 5 were given 100 (CA100), 200 (CA200) and 300 (CA300) mg/kg, respectively, of the hydroalcoholic extract of C. abyssinica. Blood samples were then collected at different time points to determine blood glucose levels (BGL). Data were analyzed using one way ANOVA followed by Dunnet’s post hoc test and p < 0.05was considered as statistically significant. Results In normal mice, CA200 and GL5 induced hypoglycemia starting from the 2nd h but the hypoglycemic effect of CA300 was delayed and appeared at the 4th h (p < 0.05 in all cases). In diabetic mice, BGL was significantly reduced by CA100 (p < 0.05) and CA300 (p < 0.01) starting from the 3rd h, whereas CA200 (p < 0.001) and GL5 (p < 0.05) attained this effect as early as the 2nd h. In OGTT, TW80 (p < 0.01) and CA100 (p < 0.01) brought down BGL significantly at 120 min, while CA200 (p < 0.001) and GL5 (p < 0.001) achieved this effect at 60 min indicating the oral glucose load improving activity of the extract. By contrast, CA300 was observed to have no effect on OGTT. Acute toxicity study revealed the safety of the extract even at a dose of 2000 mg/kg. Preliminary phytochemical study demonstrated the presence of various secondary metabolites, including, among others

  1. Purely Cortical Anaplastic Ependymoma

    PubMed Central

    Romero, Flávio Ramalho; Zanini, Marco Antônio; Ducati, Luis Gustavo; Vital, Roberto Bezerra; de Lima Neto, Newton Moreira; Gabarra, Roberto Colichio

    2012-01-01

    Ependymomas are glial tumors derived from ependymal cells lining the ventricles and the central canal of the spinal cord. It may occur outside the ventricular structures, representing the extraventicular form, or without any relationship of ventricular system, called ectopic ependymona. Less than fifteen cases of ectopic ependymomas were reported and less than five were anaplastic. We report a rare case of pure cortical ectopic anaplastic ependymoma. PMID:23119204

  2. Purely cortical anaplastic ependymoma.

    PubMed

    Romero, Flávio Ramalho; Zanini, Marco Antônio; Ducati, Luis Gustavo; Vital, Roberto Bezerra; de Lima Neto, Newton Moreira; Gabarra, Roberto Colichio

    2012-01-01

    Ependymomas are glial tumors derived from ependymal cells lining the ventricles and the central canal of the spinal cord. It may occur outside the ventricular structures, representing the extraventicular form, or without any relationship of ventricular system, called ectopic ependymona. Less than fifteen cases of ectopic ependymomas were reported and less than five were anaplastic. We report a rare case of pure cortical ectopic anaplastic ependymoma.

  3. Pure Lovelock Kasner metrics

    NASA Astrophysics Data System (ADS)

    Camanho, Xián O.; Dadhich, Naresh; Molina, Alfred

    2015-09-01

    We study pure Lovelock vacuum and perfect fluid equations for Kasner-type metrics. These equations correspond to a single Nth order Lovelock term in the action in d=2N+1,2N+2 dimensions, and they capture the relevant gravitational dynamics when aproaching the big-bang singularity within the Lovelock family of theories. Pure Lovelock gravity also bears out the general feature that vacuum in the critical odd dimension, d=2N+1, is kinematic, i.e. we may define an analogue Lovelock-Riemann tensor that vanishes in vacuum for d=2N+1, yet the Riemann curvature is non-zero. We completely classify isotropic and vacuum Kasner metrics for this class of theories in several isotropy types. The different families can be characterized by means of certain higher order 4th rank tensors. We also analyze in detail the space of vacuum solutions for five- and six dimensional pure Gauss-Bonnet theory. It possesses an interesting and illuminating geometric structure and symmetries that carry over to the general case. We also comment on a closely related family of exponential solutions and on the possibility of solutions with complex Kasner exponents. We show that the latter imply the existence of closed timelike curves in the geometry.

  4. 7 CFR 917.8 - Pure grower or pure producer.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE FRESH PEARS AND PEACHES GROWN IN CALIFORNIA Order Regulating Handling Definitions § 917.8 Pure grower or pure producer. (a) For peaches,...

  5. 7 CFR 917.8 - Pure grower or pure producer.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE FRESH PEARS AND PEACHES GROWN IN CALIFORNIA Order Regulating Handling Definitions § 917.8 Pure grower or pure producer. (a) For peaches,...

  6. Used Nuclear Fuel Loading and Structural Performance Under Normal Conditions of Transport- Demonstration of Approach and Results on Used Fuel Performance Characterization

    SciTech Connect

    Adkins, Harold; Geelhood, Ken; Koeppel, Brian; Coleman, Justin; Bignell, John; Flores, Gregg; Wang, Jy-An; Sanborn, Scott; Spears, Robert; Klymyshyn, Nick

    2013-09-30

    This document addresses Oak Ridge National Laboratory milestone M2FT-13OR0822015 Demonstration of Approach and Results on Used Nuclear Fuel Performance Characterization. This report provides results of the initial demonstration of the modeling capability developed to perform preliminary deterministic evaluations of moderate-to-high burnup used nuclear fuel (UNF) mechanical performance under normal conditions of storage (NCS) and normal conditions of transport (NCT) conditions. This report also provides results from the sensitivity studies that have been performed. Finally, discussion on the long-term goals and objectives of this initiative are provided.

  7. The effect of glucose loading on urinary excretion of chromium in normal adults, in individuals from diabetic families and in diabetics.

    PubMed

    Gürson, C T; Saner, G

    1978-07-01

    This study was designed to investigate the effect of oral glucose tolerance tests (OGTT) on urinary chromium excretion in normal individuals, in individuals belonging to diabetic families, and in diabetics. The results can be summarized as: 1) eight of the 10 normal adults showed a significant increase both in terms of chromium per minute and chromium/creatinine (Cr/Cre) ratio after OGTT, and the difference between the mean values before and after OGTT was significant, 2) Of the 13 individuals from diabetic families, only five increased their chromium excretion and chromium/creatinine ratio after the glucose challenge (39%). However, the mean values for the group before and after OGTT remained statistically unchanged, 3) three of eight overt diabetic subjects (38%) showed moderate increase the chromium excretion and Cr/Cre ratio after OGTT, but the mean values were not effected. The creatinine values in urine remained constant before and after OGTT in all groups. These results suggest that a positive Cr/Cre response is more likely to occur in groups of normals than in groups of diabetics, and in individuals from diabetic families.

  8. Pure gonadal dysgenesis (46 XX type) with a familial pattern.

    PubMed

    Kohmanaee, Shahin; Dalili, Setila; Rad, Afagh Hassanzadeh

    2015-01-01

    46, XX gonadal dysgenesis without the phenotype of Turner's syndrome is described as "pure". Although, previous investigations obtained that commonly gonadal dysgenesis did not cause breast development as a result of low levels of circulating estradiol. However, in this study, we aimed to report a familial pure gonadal dysgenesis with and without normal secondary sexual characteristics. In this study, we reported three siblings with pure gonadal dysgenesis with and without normal secondary sexual characteristics. The elder two sisters had a normal female phenotype and the youngest had amenorrhea with no breast development (B1) and pubic hair. In addition, it seems that the absence of pubic hair occurred due to delayed constitutional puberty. According to results, it seems that clinicians should consider different presentations for pure gonadal dysgenesis with familial pattern.

  9. Pure progressive amnesia: An atypical amnestic syndrome?

    PubMed

    Barbeau, Emmanuel J; Didic, Mira; Felician, Olivier; Tramoni, Eve; Guedj, Eric; Ceccaldi, Mathieu; Poncet, Michel

    2006-12-01

    We report on M.S., an 83-year-old patient with isolated pure progressive amnesia. This rare, recently identified, form of amnesia has been described in elderly patients. Neuropathological studies suggest that this syndrome is an atypical clinical presentation of Alzheimer's disease. The aim of our study was to characterize the neuropsychological pattern of pure progressive amnesia in comparison with other amnestic syndromes and memory dissociations reported in the literature. Our results indicate that pure progressive amnesia is characterized by a highly unusual dissociation in the realm of memory, with severe deficits on tests based on recognition and recall of verbal and visual single items, contrasting with relatively preserved anterograde autobiographical and spatial memory and normal recall of complex material such as stories. These findings suggest that memory for single items could depend on an independent system. One hypothesis is that M.S.'s unusual memory profile results from relative dysfunction of the ventral medial temporal lobe pathway. An alternative explanation implicates cognitive reserve. Further studies are required in order to progress on this matter. In any case, pure progressive amnesia is a clinical syndrome that may provide further insight into the organization of declarative memory.

  10. Effect of humidity on fretting wear of several pure metals

    NASA Technical Reports Server (NTRS)

    Goto, H.; Buckley, D. H.

    1984-01-01

    Fretting wear experiments with several pure metals were conducted in air at various relative humidity levels. The materials used were iron, aluminum, copper, silver, chromium, titanium, and nickel. Each pure metal had a maximum fretting wear volume at a specific humidity level RH sub max that was not dependent on mechanical factors such as contact load, fretting amplitude, and frequency in the ranges studied. The weight loss due to fretting wear at RH sub max for each pure metal decreased with increasing heat of oxygen adsorption on the metal, indicating that adhesive wear dominated at RH sub max.

  11. Acquired pure megakaryocytic aplasia successfully treated with cyclosporine.

    PubMed

    Omri, Halima El; Ibrahim, Firyal; Taha, Ruba Yasin; Negm, Riham Hassan; Khinji, Aisha Al; Yassin, Mohammed; Hijji, Ibrahim Al; Ayoubi, Hanadi El; Baden, Hussein

    2010-12-01

    Acquired pure megakaryocytic aplasia is a rare hematological disorder characterized by thrombocytopenia with absent or markedly reduced megakaryocytes in the bone marrow. We report a case of a 25-year-old male diagnosed as acquired pure megakaryocytic aplasia. Treatment with prednisone and intravenous immunoglobulin failed, but he was successfully treated with cyclosporine, with complete remission after 90 days and normal platelet count maintained thereafter. PMID:27263744

  12. Analytical and Numerical Results for an Adhesively Bonded Joint Subjected to Pure Bending

    NASA Technical Reports Server (NTRS)

    Smeltzer, Stanley S., III; Lundgren, Eric

    2006-01-01

    A one-dimensional, semi-analytical methodology that was previously developed for evaluating adhesively bonded joints composed of anisotropic adherends and adhesives that exhibit inelastic material behavior is further verified in the present paper. A summary of the first-order differential equations and applied joint loading used to determine the adhesive response from the methodology are also presented. The method was previously verified against a variety of single-lap joint configurations from the literature that subjected the joints to cases of axial tension and pure bending. Using the same joint configuration and applied bending load presented in a study by Yang, the finite element analysis software ABAQUS was used to further verify the semi-analytical method. Linear static ABAQUS results are presented for two models, one with a coarse and one with a fine element meshing, that were used to verify convergence of the finite element analyses. Close agreement between the finite element results and the semi-analytical methodology were determined for both the shear and normal stress responses of the adhesive bondline. Thus, the semi-analytical methodology was successfully verified using the ABAQUS finite element software and a single-lap joint configuration subjected to pure bending.

  13. Characterization of crack growth under combined loading

    NASA Technical Reports Server (NTRS)

    Feldman, A.; Smith, F. W.; Holston, A., Jr.

    1977-01-01

    Room-temperature static and cyclic tests were made on 21 aluminum plates in the shape of a 91.4x91.4-cm Maltese cross with 45 deg flaws to develop crack growth and fracture toughness data under mixed-mode conditions. During cyclic testing, it was impossible to maintain a high proportion of shear-mode deformation on the crack tips. Cracks either branched or turned. Under static loading, cracks remained straight if shear stress intensity exceeded normal stress intensity. Mixed-mode crack growth rate data compared reasonably well with published single-mode data, and measured crack displacements agreed with the straight and branched crack analyses. Values of critical strain energy release rate at fracture for pure shear were approximately 50% higher than for pure normal opening, and there was a large reduction in normal stress intensity at fracture in the presence of high shear stress intensity. Net section stresses were well into the inelastic range when fracture occurred under high shear on the cracks.

  14. Towards multiple hazard resilient bridges: a methodology for modeling frequent and infrequent time-varying loads Part I, Comprehensive reliability and partial failure probabilities

    NASA Astrophysics Data System (ADS)

    Liang, Zach; Lee, George C.

    2012-09-01

    The current AASHTO load and resistance factor design (LRFD) guidelines are formulated based on bridge reliability, which interprets traditional design safety factors into more rigorously deduced factors based on the theory of probability. This is a major advancement in bridge design specifications. However, LRFD is only calibrated for dead and live loads. In cases when extreme loads are significant, they need to be individually assessed. Combining regular loads with extreme loads has been a major challenge, mainly because the extreme loads are time variables and cannot be directly combined with time invariant loads to formulate the probability of structural failure. To overcome these difficulties, this paper suggests a methodology of comprehensive reliability, by introducing the concept of partial failure probability to separate the loads so that each individual load combination under a certain condition can be approximated as time invariant. Based on these conditions, the extreme loads (also referred to as multiple hazard or MH loads) can be broken down into single effects. In Part II of this paper, a further breakdown of these conditional occurrence probabilities into pure conditions is discussed by using a live truck and earthquake loads on a bridge as an example. There are three major steps in establishing load factors from MH load distributions: (1) formulate the failure probabilities; (2) normalize various load distributions; and (3) establish design limit state equations. This paper describes the formulation of the failure probabilities of single and combined loads.

  15. 14 CFR 23.537 - Seawing loads.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23.537 Seawing loads. Seawing design loads must be based on applicable test data. Emergency Landing Conditions...

  16. 14 CFR 23.537 - Seawing loads.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23.537 Seawing loads. Seawing design loads must be based on applicable test data. Emergency Landing Conditions...

  17. "Pure" cutaneous histiocytosis-X.

    PubMed

    Wolfson, S L; Botero, F; Hurwitz, S; Pearson, H A

    1981-11-15

    The case histories of two young children who experienced skin rashes involving various areas of the body are reported. The diagnosis of pure cutaneous histiocytosis-X was established after extensive studies revealed no other organ involvement. The patients were treated with oral corticosteroids. Currently, both children are in good health, show no evidence of disease, and have been followed over a four-to-five-year period. Therapy with corticosteroids may not be indicated with pure cutaneous histiocytosis-X unless there is evidence of extracutaneous dissemination or rapid progression of the disease.

  18. Production of substantially pure fructose

    DOEpatents

    Hatcher, Herbert J.; Gallian, John J.; Leeper, Stephen A.

    1990-01-01

    A process is disclosed for the production of substantially pure fructose from sucrose-containing substrates. The process comprises converting the sucrose to levan and glucose, purifying the levan by membrane technology, hydrolyzing the levan to form fructose monomers, and recovering the fructose.

  19. Microstructural effects on fracture toughness of polycrystalline ceramics in combined mode I and mode II loading

    NASA Technical Reports Server (NTRS)

    Singh, D.; Shetty, D. K.

    1988-01-01

    Fracture toughness of polycrystalline alumina and ceria partially-stabilized tetragonal zirconia (CeO2-TZP) ceramics were assessed in combined mode I and mode II loading using precracked disk specimens in diametral compression. Stress states ranging from pure mode I, combined mode I and mode II, and pure mode II were obtained by aligning the center crack at specific angles relative to the loading diameter. The resulting mixed-mode fracture toughness envelope showed significant deviation to higher fracture toughness in mode II relative to the predictions of the linear elastic fracture mechanics theory. Critical comparison with corresponding results on soda-lime glass and fracture surface observations showed that crack surface resistance arising from grain interlocking and abrasion was the main source of the increased fracture toughness in mode II loading of the polycrystalline ceramics. The normalized fracture toughness for pure mode II loading, (KII/KIc), increased with increasing grain size for the CeO2-TZP ceramics. Quantitative fractography confirmed an increased percentage of transgranular fracture of the grains in mode II loading.

  20. Computer Pure-Tone and Operator Stress: Report III.

    ERIC Educational Resources Information Center

    Dow, Caroline; Covert, Douglas C.

    Pure-tone sound at 15,750 Herz generated by flyback transformers in many computer and video display terminal (VDT) monitors has stress-related productivity effects in some operators, especially women. College-age women in a controlled experiment simulating half a normal work day showed responses within the first half hour of exposure to a tone…

  1. Similarities and differences between learning abilities, "pure" learning disabilities, "pure" ADHD and comorbid ADHD with learning disabilities.

    PubMed

    Mangina, Constantine A; Beuzeron-Mangina, Helen

    2009-08-01

    This research pursues the crucial question of the differentiation of preadolescents with "Pure" ADHD, comorbid ADHD with learning disabilities, "Pure" learning disabilities and age-matched normal controls. For this purpose, Topographic Mapping of Event-Related Brain Potentials (ERPs) to a Memory Workload Paradigm with visually presented words, Bilateral Electrodermal Activity during cognitive workload and Mangina-Test performance were used. The analysis of Topographic distribution of amplitudes revealed that normal preadolescents were significantly different from "Pure" ADHD (P<0.0001), "Pure" learning disabilities (P<0.0001), and comorbid ADHD with learning disabilities (P<0.0009), by displaying enhanced prefrontal and frontal negativities (N450). In contrast, preadolescents with "Pure" ADHD and comorbid ADHD with learning disabilities have shown a marked reduction of prefrontal and frontal negativities (N450). As for the "Pure" Learning Disabled preadolescents, very small positivities (P450) in prefrontal and frontal regions were obtained as compared to the other pathological groups. Bilateral Electrodermal Activity during cognitive workload revealed a significant main effect for groups (P<0.00001), Left versus Right (P=0.0029) and sessions (P=0.0136). A significant main effect for the Mangina-Test performance which separated the four groups was found (P<0.000001). Overall, these data support the existence of clear differences and similarities between the pathological preadolescent groups as opposed to age-matched normal controls. The psychophysiological differentiation of these groups, provides distinct biological markers which integrate central, autonomic and neuropsychometric variables by targeting the key features of these pathologies for diagnosis and intervention strategies and by providing knowledge for the understanding of normal neurocognitive processes and functions.

  2. Canonical Thermal Pure Quantum State

    NASA Astrophysics Data System (ADS)

    Sugiura, Sho; Shimizu, Akira

    2013-07-01

    A thermal equilibrium state of a quantum many-body system can be represented by a typical pure state, which we call a thermal pure quantum (TPQ) state. We construct the canonical TPQ state, which corresponds to the canonical ensemble of the conventional statistical mechanics. It is related to the microcanonical TPQ state, which corresponds to the microcanonical ensemble, by simple analytic transformations. Both TPQ states give identical thermodynamic results, if both ensembles do, in the thermodynamic limit. The TPQ states corresponding to other ensembles can also be constructed. We have thus established the TPQ formulation of statistical mechanics, according to which all quantities of statistical-mechanical interest are obtained from a single realization of any TPQ state. We also show that it has great advantages in practical applications. As an illustration, we study the spin-1/2 kagome Heisenberg antiferromagnet.

  3. Load cell

    DOEpatents

    Spletzer, B.L.

    1998-12-15

    A load cell combines the outputs of a plurality of strain gauges to measure components of an applied load. Combination of strain gauge outputs allows measurement of any of six load components without requiring complex machining or mechanical linkages to isolate load components. An example six axis load cell produces six independent analog outputs, each directly proportional to one of the six general load components. 16 figs.

  4. Load cell

    DOEpatents

    Spletzer, Barry L.

    2001-01-01

    A load cell combines the outputs of a plurality of strain gauges to measure components of an applied load. Combination of strain gauge outputs allows measurement of any of six load components without requiring complex machining or mechanical linkages to isolate load components. An example six axis load cell produces six independent analog outputs which can be combined to determine any one of the six general load components.

  5. Load cell

    DOEpatents

    Spletzer, Barry L.

    1998-01-01

    A load cell combines the outputs of a plurality of strain gauges to measure components of an applied load. Combination of strain gauge outputs allows measurement of any of six load components without requiring complex machining or mechanical linkages to isolate load components. An example six axis load cell produces six independent analog outputs, each directly proportional to one of the six general load components.

  6. Pure and aerated water entry of a flat plate

    NASA Astrophysics Data System (ADS)

    Ma, Z. H.; Causon, D. M.; Qian, L.; Mingham, C. G.; Mai, T.; Greaves, D.; Raby, A.

    2016-01-01

    This paper presents an experimental and numerical investigation of the entry of a rigid square flat plate into pure and aerated water. Attention is focused on the measurement and calculation of the slamming loads on the plate. The experimental study was carried out in the ocean basin at Plymouth University's COAST laboratory. The present numerical approach extends a two-dimensional hydro-code to compute three-dimensional hydrodynamic impact problems. The impact loads on the structure computed by the numerical model compare well with laboratory measurements. It is revealed that the impact loading consists of distinctive features including (1) shock loading with a high pressure peak, (2) fluid expansion loading associated with very low sub-atmospheric pressure close to the saturated vapour pressure, and (3) less severe secondary reloading with super-atmospheric pressure. It is also disclosed that aeration introduced into water can effectively reduce local pressures and total forces on the flat plate. The peak impact loading on the plate can be reduced by half or even more with 1.6% aeration in water. At the same time, the lifespan of shock loading is prolonged by aeration, and the variation of impulse is less sensitive to the change of aeration than the peak loading.

  7. Pure-tone birdsong by resonance filtering of harmonic overtones

    PubMed Central

    Beckers, Gabriël J. L.; Suthers, Roderick A.; Cate, Carel ten

    2003-01-01

    Pure-tone song is a common and widespread phenomenon in birds. The mechanistic origin of this type of phonation has been the subject of long-standing discussion. Currently, there are three hypotheses. (i) A vibrating valve in the avian vocal organ, the syrinx, generates a multifrequency harmonic source sound, which is filtered to a pure tone by a vocal tract filter (“source-filter” model, analogous to human speech production). (ii) Vocal tract resonances couple with a vibrating valve source, suppressing the normal production of harmonic overtones at this source (“soprano” model, analogous to human soprano singing). (iii) Pure-tone sound is produced as such by a sound-generating mechanism that is fundamentally different from a vibrating valve. Here we present direct evidence of a source-filter mechanism in the production of pure-tone birdsong. Using tracheal thermistors and air sac pressure cannulae, we recorded sound signals close to the syringeal sound source during spontaneous, pure-tone vocalizations of two species of turtledove. The results show that pure-tone dove vocalizations originate through filtering of a multifrequency harmonic sound source. PMID:12764226

  8. Cable load sensing device

    DOEpatents

    Beus, Michael J.; McCoy, William G.

    1998-01-01

    Apparatus for sensing the magnitude of a load on a cable as the cable is employed to support the load includes a beam structure clamped to the cable so that a length of the cable lies along the beam structure. A spacer associated with the beam structure forces a slight curvature in a portion of the length of cable under a cable "no-load" condition so that the portion of the length of cable is spaced from the beam structure to define a cable curved portion. A strain gauge circuit including strain gauges is secured to the beam structure by welding. As the cable is employed to support a load the load causes the cable curved portion to exert a force normal to the cable through the spacer and on the beam structure to deform the beam structure as the cable curved portion attempts to straighten under the load. As this deformation takes place, the resistance of the strain gauges is set to a value proportional to the magnitude of the normal strain on the beam structure during such deformation. The magnitude of the normal strain is manipulated in a control device to generate a value equal to the magnitude or weight of the load supported by the cable.

  9. Synthesis of Enantiomerically Pure Anthracyclinones

    NASA Astrophysics Data System (ADS)

    Achmatowicz, Osman; Szechner, Barbara

    The anthracycline antibiotics are among the most important clinical drugs used in the treatment of human cancer. The search for new agents with improved therapeutic efficacy and reduced cardiotoxicity stimulated considerable efforts in the synthesis of new analogues. Since the biological activity of anthracyclines depends on their natural absolute configuration, various strategies for the synthesis of enantiomerically pure anthracyclinones (aglycones) have been developed. They comprise: resolution of racemic intermediate, incorporation of a chiral fragment derived from natural and non-natural chiral pools, asymmetric synthesis with the use of a chiral auxiliary or a chiral reagent, and enantioselective catalysis. Synthetic advances towards enantiopure anthracyclinones reported over the last 17 years are reviewed.

  10. Production of substantially pure fructose

    SciTech Connect

    Hatcher, H.J.; Gallian, J.J.; Leeper, S.A.

    1990-05-22

    This patent describes a process for the production of a substantially pure product containing greater than 60% fructose. It comprises: combining a sucrose-containing substrate with effective amounts of a levansucrase enzyme preparation to form levan and glucose; purifying the levan by at least one of the following purification methods: ultrafiltration, diafiltration, hyperfiltration, reverse osmosis, liquid--liquid partition, solvent extraction, chromatography, and precipitation; hydrolyzing the levan to form fructose substantially free of glucose and sucrose; and recovering the fructose by at least one of the following recovery methods: hyperfiltration, reverse osmosis, evaporation, drying, crystallization, and chromatography.

  11. Strength tests of thin-walled elliptic duralumin cylinders in pure bending and in combined pure bending and torsion

    NASA Technical Reports Server (NTRS)

    Lundquist, Eugene E; Stowell, Elbridge Z

    1942-01-01

    An analysis is presented of the results of tests made by the Massachusetts Institute of Technology and by the National Advisory Committee for Aeronautics on an investigation of the strength of thin-walled circular and elliptic cylinders in pure bending and in combined torsion and bending. In each of the loading conditions, the bending moments were applied in the plane of the major axis of the ellipse.

  12. Multivariate normality

    NASA Technical Reports Server (NTRS)

    Crutcher, H. L.; Falls, L. W.

    1976-01-01

    Sets of experimentally determined or routinely observed data provide information about the past, present and, hopefully, future sets of similarly produced data. An infinite set of statistical models exists which may be used to describe the data sets. The normal distribution is one model. If it serves at all, it serves well. If a data set, or a transformation of the set, representative of a larger population can be described by the normal distribution, then valid statistical inferences can be drawn. There are several tests which may be applied to a data set to determine whether the univariate normal model adequately describes the set. The chi-square test based on Pearson's work in the late nineteenth and early twentieth centuries is often used. Like all tests, it has some weaknesses which are discussed in elementary texts. Extension of the chi-square test to the multivariate normal model is provided. Tables and graphs permit easier application of the test in the higher dimensions. Several examples, using recorded data, illustrate the procedures. Tests of maximum absolute differences, mean sum of squares of residuals, runs and changes of sign are included in these tests. Dimensions one through five with selected sample sizes 11 to 101 are used to illustrate the statistical tests developed.

  13. Load measurement system with load cell lock-out mechanism

    NASA Astrophysics Data System (ADS)

    Le, Thang; Carroll, Monty; Liu, Jonathan

    1995-05-01

    In the frame work of the project Shuttle Plume Impingement Flight Experiment (SPIFEX), a Load Measurement System was developed and fabricated to measure the impingement force of Shuttle Reaction Control System (RCS) jets. The Load Measurement System is a force sensing system that measures any combination of normal and shear forces up to 40 N (9 lbf) in the normal direction and 22 N (5 lbf) in the shear direction with an accuracy of +/- 0.04 N (+/- 0.01 lbf) Since high resolution is required for the force measurement, the Load Measurement System is built with highly sensitive load cells. To protect these fragile load cells in the non-operational mode from being damaged due to flight loads such as launch and landing loads of the Shuttle vehicle, a motor driven device known as the Load Cell Lock-Out Mechanism was built. This Lock-Out Mechanism isolates the load cells from flight loads and re-engages the load cells for the force measurement experiment once in space. With this highly effective protection system, the SPIFEX load measurement experiment was successfully conducted on STS-44 in September 1994 with all load cells operating properly and reading impingement forces as expected.

  14. Lack of Erythropoietic Inhibitory Effect of Serum From Patients with Congenital Pure Red Cell Aplasia

    ERIC Educational Resources Information Center

    Geller, Gary; And Others

    1975-01-01

    Serum of five children ages 1 to 19 months with congenital pure red cell aplasia (incomplete or defective development of red blood cells) was injected in normal mice to determine possible inhibition of red blood cell formulating stimulants. (CL)

  15. 76 FR 69284 - Pure Magnesium From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-08

    ... COMMISSION Pure Magnesium From China Determination On the basis of the record \\1\\ developed in the subject... order on pure magnesium from China would be likely to lead to continuation or recurrence of material... USITC Publication 4274 (October 2011), entitled Pure Magnesium from China: Investigation No....

  16. Extraction of distance restraints from pure shift NOE experiments

    NASA Astrophysics Data System (ADS)

    Kaltschnee, Lukas; Knoll, Kevin; Schmidts, Volker; Adams, Ralph W.; Nilsson, Mathias; Morris, Gareth A.; Thiele, Christina M.

    2016-10-01

    NMR techniques incorporating pure shift methods to improve signal resolution have recently attracted much attention, owing to their potential use in studies of increasingly complex molecular systems. Extraction of frequencies from these simplified spectra enables easier structure determination, but only a few of the methods presented provide structural parameters derived from signal integral measurements. In particular, for quantification of the nuclear Overhauser effect (NOE) it is highly desirable to utilize pure shift techniques where signal overlap normally prevents accurate signal integration, to enable measurement of a larger number of interatomic distances. However, robust methods for the measurement of interatomic distances using the recently developed pure shift techniques have not been reported to date. In this work we discuss some of the factors determining the accuracy of measurements of signal integrals in interferogram-based Zangger-Sterk (ZS) pure shift NMR experiments. The ZS broadband homodecoupling technique is used in different experiments designed for quantitative NOE determination from pure shift spectra. It is shown that the techniques studied can be used for quantitative extraction of NOE-derived distance restraints, as exemplified for the test case of strychnine.

  17. Normalizing Rejection.

    PubMed

    Conn, Vicki S; Zerwic, Julie; Jefferson, Urmeka; Anderson, Cindy M; Killion, Cheryl M; Smith, Carol E; Cohen, Marlene Z; Fahrenwald, Nancy L; Herrick, Linda; Topp, Robert; Benefield, Lazelle E; Loya, Julio

    2016-02-01

    Getting turned down for grant funding or having a manuscript rejected is an uncomfortable but not unusual occurrence during the course of a nurse researcher's professional life. Rejection can evoke an emotional response akin to the grieving process that can slow or even undermine productivity. Only by "normalizing" rejection, that is, by accepting it as an integral part of the scientific process, can researchers more quickly overcome negative emotions and instead use rejection to refine and advance their scientific programs. This article provides practical advice for coming to emotional terms with rejection and delineates methods for working constructively to address reviewer comments. PMID:26041785

  18. Mixtures of maximally entangled pure states

    NASA Astrophysics Data System (ADS)

    Flores, M. M.; Galapon, E. A.

    2016-09-01

    We study the conditions when mixtures of maximally entangled pure states remain entangled. We found that the resulting mixed state remains entangled when the number of entangled pure states to be mixed is less than or equal to the dimension of the pure states. For the latter case of mixing a number of pure states equal to their dimension, we found that the mixed state is entangled provided that the entangled pure states to be mixed are not equally weighted. We also found that one can restrict the set of pure states that one can mix from in order to ensure that the resulting mixed state is genuinely entangled. Also, we demonstrate how these results could be applied as a way to detect entanglement in mixtures of the entangled pure states with noise.

  19. Mott localization in a pure stripe antiferromagnet Rb1-δFe1.5-σS2

    SciTech Connect

    Wang, Meng; Yi, Ming; Cao, Huibo; de la Cruz, C.; Mo, S. K.; Huang, Q. Z.; Bourret-Courchesne, E.; Dai, Pengcheng; Lee, D. H.; Shen, Z. X.; Birgeneau, R. J.

    2015-09-01

    A combination of neutron diffraction and angle-resolved photoemission spectroscopy measurements on a pure antiferromagnetic stripe Rb1-δFe1.5-σS2 is reported. A neutron diffraction experiment on a powder sample shows that a 98% volume fraction of the sample is in the antiferromagnetic stripe phase with rhombic iron vacancy order and a refined composition of Rb0.66Fe1.36S2, and that only 2% of the sample is in the block antiferromagnetic phase with √5×√5 iron vacancy order. Furthermore, a neutron diffraction experiment on a single crystal shows that there is only a single phase with the stripe antiferromagnetic order with the refined composition of Rb0.78Fe1.35S2, while the phase with block antiferromagnetic order is absent. Angle-resolved photoemission spectroscopy measurements on the same crystal with the pure stripe phase reveal that the electronic structure is gapped at the Fermi level with a gap larger than 0.325 eV. The data collectively demonstrate that the extra 10% iron vacancies in addition to the rhombic iron vacancy order effectively impede the formation of the block antiferromagnetic phase; the data also suggest that the stripe antiferromagnetic phase with rhombic iron vacancy order is a Mott insulator.

  20. Isomerically Pure Tetramethylrhodamine Voltage Reporters.

    PubMed

    Deal, Parker E; Kulkarni, Rishikesh U; Al-Abdullatif, Sarah H; Miller, Evan W

    2016-07-27

    We present the design, synthesis, and application of a new family of fluorescent voltage indicators based on isomerically pure tetramethylrhodamines. These new Rhodamine Voltage Reporters, or RhoVRs, use photoinduced electron transfer (PeT) as a trigger for voltage sensing, display excitation and emission profiles in the green to orange region of the visible spectrum, demonstrate high sensitivity to membrane potential changes (up to 47% ΔF/F per 100 mV), and employ a tertiary amide derived from sarcosine, which aids in membrane localization and simultaneously simplifies the synthetic route to the voltage sensors. The most sensitive of the RhoVR dyes, RhoVR 1, features a methoxy-substituted diethylaniline donor and phenylenevinylene molecular wire at the 5'-position of the rhodamine aryl ring, exhibits the highest voltage sensitivity to date for red-shifted PeT-based voltage sensors, and is compatible with simultaneous imaging alongside green fluorescent protein-based indicators. The discoveries that sarcosine-based tertiary amides in the context of molecular-wire voltage indicators prevent dye internalization and 5'-substituted voltage indicators exhibit improved voltage sensitivity should be broadly applicable to other types of PeT-based voltage-sensitive fluorophores. PMID:27428174

  1. Bringing Planctomycetes into pure culture

    PubMed Central

    Lage, Olga M.; Bondoso, Joana

    2012-01-01

    Planctomycetes have been known since the description of Planctomyces bekefii by Gimesi at the beginning of the twentieth century (1924), although the first axenic cultures were only obtained in the 1970s. Since then, 11 genera with 14 species have been validly named and five candidatus genera belonging to the anaerobic ammonium oxidation, anammox bacteria have also been discovered. However, Planctomycetes diversity is much broader than these numbers indicate, as shown by environmental molecular studies. In recent years, the authors have attempted to isolate and cultivate additional strains of Planctomycetes. This paper provides a summary of the isolation work that was carried out to obtain in pure culture Planctomycetes from several environmental sources. The following strains of planctomycetes have been successfully isolated: two freshwater strains from the sediments of an aquarium, which were described as a new genus and species, Aquisphaera giovannonii; several Rhodopirellula strains from the sediments of a water treatment recycling tank of a marine fish farm; and more than 140 planctomycetes from the biofilm community of macroalgae. This collection comprises several novel taxa that are being characterized and described. Improvements in the isolation methodology were made in order to optimize and enlarge the number of Planctomycetes isolated from the macroalgae. The existence of an intimate and an important relationship between planctomycetes and macroalgae reported before by molecular studies is therefore supported by culture-dependent methods. PMID:23335915

  2. Normal development.

    PubMed

    Girard, Nadine; Koob, Meriam; Brunel, Herv

    2016-01-01

    Numerous events are involved in brain development, some of which are detected by neuroimaging. Major changes in brain morphology are depicted by brain imaging during the fetal period while changes in brain composition can be demonstrated in both pre- and postnatal periods. Although ultrasonography and computed tomography can show changes in brain morphology, these techniques are insensitive to myelination that is one of the most important events occurring during brain maturation. Magnetic resonance imaging (MRI) is therefore the method of choice to evaluate brain maturation. MRI also gives insight into the microstructure of brain tissue through diffusion-weighted imaging and diffusion tensor imaging. Metabolic changes are also part of brain maturation and are assessed by proton magnetic resonance spectroscopy. Understanding and knowledge of the different steps in brain development are required to be able to detect morphologic and structural changes on neuroimaging. Consequently alterations in normal development can be depicted. PMID:27430460

  3. Biomechanical modelling of normal pressure hydrocephalus.

    PubMed

    Dutta-Roy, Tonmoy; Wittek, Adam; Miller, Karol

    2008-07-19

    This study investigates the mechanics of normal pressure hydrocephalus (NPH) growth using a computational approach. We created a generic 3-D brain mesh of a healthy human brain and modelled the brain parenchyma as single phase and biphasic continuum. In our model, hyperelastic constitutive law and finite deformation theory described deformations within the brain parenchyma. We used a value of 155.77Pa for the shear modulus (mu) of the brain parenchyma. Additionally, in our model, contact boundary definitions constrained the brain outer surface inside the skull. We used transmantle pressure difference to load the model. Fully nonlinear, implicit finite element procedures in the time domain were used to obtain the deformations of the ventricles and the brain. To the best of our knowledge, this was the first 3-D, fully nonlinear model investigating NPH growth mechanics. Clinicians generally accept that at most 1mm of Hg transmantle pressure difference (133.416Pa) is associated with the condition of NPH. Our computations showed that transmantle pressure difference of 1mm of Hg (133.416Pa) did not produce NPH for either single phase or biphasic model of the brain parenchyma. A minimum transmantle pressure difference of 1.764mm of Hg (235.44Pa) was required to produce the clinical condition of NPH. This suggested that the hypothesis of a purely mechanical basis for NPH growth needs to be revised. We also showed that under equal transmantle pressure difference load, there were no significant differences between the computed ventricular volumes for biphasic and incompressible/nearly incompressible single phase model of the brain parenchyma. As a result, there was no major advantage gained by using a biphasic model for the brain parenchyma. We propose that for modelling NPH, nearly incompressible single phase model of the brain parenchyma was adequate. Single phase treatment of the brain parenchyma simplified the mathematical description of the NPH model and resulted in

  4. A Hybrid Sensing Approach for Pure and Adulterated Honey Classification

    PubMed Central

    Subari, Norazian; Saleh, Junita Mohamad; Shakaff, Ali Yeon Md; Zakaria, Ammar

    2012-01-01

    This paper presents a comparison between data from single modality and fusion methods to classify Tualang honey as pure or adulterated using Linear Discriminant Analysis (LDA) and Principal Component Analysis (PCA) statistical classification approaches. Ten different brands of certified pure Tualang honey were obtained throughout peninsular Malaysia and Sumatera, Indonesia. Various concentrations of two types of sugar solution (beet and cane sugar) were used in this investigation to create honey samples of 20%, 40%, 60% and 80% adulteration concentrations. Honey data extracted from an electronic nose (e-nose) and Fourier Transform Infrared Spectroscopy (FTIR) were gathered, analyzed and compared based on fusion methods. Visual observation of classification plots revealed that the PCA approach able to distinct pure and adulterated honey samples better than the LDA technique. Overall, the validated classification results based on FTIR data (88.0%) gave higher classification accuracy than e-nose data (76.5%) using the LDA technique. Honey classification based on normalized low-level and intermediate-level FTIR and e-nose fusion data scored classification accuracies of 92.2% and 88.7%, respectively using the Stepwise LDA method. The results suggested that pure and adulterated honey samples were better classified using FTIR and e-nose fusion data than single modality data. PMID:23202033

  5. A hybrid sensing approach for pure and adulterated honey classification.

    PubMed

    Subari, Norazian; Mohamad Saleh, Junita; Md Shakaff, Ali Yeon; Zakaria, Ammar

    2012-01-01

    This paper presents a comparison between data from single modality and fusion methods to classify Tualang honey as pure or adulterated using Linear Discriminant Analysis (LDA) and Principal Component Analysis (PCA) statistical classification approaches. Ten different brands of certified pure Tualang honey were obtained throughout peninsular Malaysia and Sumatera, Indonesia. Various concentrations of two types of sugar solution (beet and cane sugar) were used in this investigation to create honey samples of 20%, 40%, 60% and 80% adulteration concentrations. Honey data extracted from an electronic nose (e-nose) and Fourier Transform Infrared Spectroscopy (FTIR) were gathered, analyzed and compared based on fusion methods. Visual observation of classification plots revealed that the PCA approach able to distinct pure and adulterated honey samples better than the LDA technique. Overall, the validated classification results based on FTIR data (88.0%) gave higher classification accuracy than e-nose data (76.5%) using the LDA technique. Honey classification based on normalized low-level and intermediate-level FTIR and e-nose fusion data scored classification accuracies of 92.2% and 88.7%, respectively using the Stepwise LDA method. The results suggested that pure and adulterated honey samples were better classified using FTIR and e-nose fusion data than single modality data. PMID:23202033

  6. Method of preparing pure fluorine gas

    DOEpatents

    Asprey, Larned B.

    1976-01-01

    A simple, inexpensive system for purifying and storing pure fluorine is described. The method utilizes alkali metal-nickel fluorides to absorb tank fluorine by forming nickel complex salts and leaving the gaseous impurities which are pumped away. The complex nickel fluoride is then heated to evolve back pure gaseous fluorine.

  7. Split-Hopkinson Pressure Bar Tests on Pure Tantalum

    NASA Astrophysics Data System (ADS)

    Dick, Richard D.; Armstrong, Ronald W.

    1997-07-01

    Pure tantalum was loaded in compression by a split-Hopkinson pressure bar (SHPB) apparatus to strain rates from 450 to 6350 s-1. These stress-strain data were added to data collected previously to evaluate and improve the constitutive equations for tantalum(Armstrong, et al., 1997, Final report to the U.S. Army Research Laboratory, Aberdeen Proving Ground, MD.). In particular, the high strain rate data were compared to SHPB data of Armstrong, et al.(Armstrong, et al., 1997, Tantalum, Published by Minerals, Metals, and Mining Society, Warrendale, PA.) for commercially prepared tantalum. The main conclusions are: 1) the flow stress - log strain rate data agree well with the Zerilli - Armstrong constitutive model for pure tantalum, 2) uniform strain exponents computed for pure tantalum are significantly smaller than for commercial tantalum relating to the presence of impurities, 3) a plot of the uniform strain exponent versus log strain rate shows good agreement with the curve predicted by Zerilli and Armstrong at strain rates above 2000 s-1, and 4) the ductility of commercial tantalum is enhanced at high strain rates because of added dislocation generation.

  8. Modelling of Fiber/Matrix Debonding of Composites Under Cyclic Loading

    NASA Technical Reports Server (NTRS)

    Naghipour, Paria; Pineda, Evan J.; Bednarcyk, Brett A.; Arnold, Steven M.

    2013-01-01

    The micromechanics theory, generalized method of cells (GMC), was employed to simulate the debonding of fiber/matrix interfaces, within a repeating unit cell subjected to global, cyclic loading, utilizing a cyclic crack growth law. Cycle dependent, interfacial debonding was implemented as a new module to the available GMC formulation. The degradation of interfacial stresses, with applied load cycles, was achieved via progressive evolution of the interfacial compliance. A periodic repeating unit cell, representing the fiber/matrix architecture of a composite, was subjected to combined normal and shear loadings, and degradation of the global transverse stress in successive cycles was monitored. The obtained results were compared to values from a corresponding finite element model. Reasonable agreement was achieved for combined normal and shear loading conditions, with minimal variation for pure loading cases. The local effects of interfacial debonding, and fatigue damage will later be combined as sub-models to predict the experimentally obtained fatigue life of Ti-15-3/Sic composites at the laminate level.

  9. Laboratory observations of fault strength in response to changes in normal stress

    USGS Publications Warehouse

    Kilgore, Brian D.; Lozos, Julian; Beeler, Nicholas M.; Oglesby, David

    2012-01-01

    Changes in fault normal stress can either inhibit or promote rupture propagation, depending on the fault geometry and on how fault shear strength varies in response to the normal stress change. A better understanding of this dependence will lead to improved earthquake simulation techniques, and ultimately, improved earthquake hazard mitigation efforts. We present the results of new laboratory experiments investigating the effects of step changes in fault normal stress on the fault shear strength during sliding, using bare Westerly granite samples, with roughened sliding surfaces, in a double direct shear apparatus. Previous experimental studies examining the shear strength following a step change in the normal stress produce contradictory results: a set of double direct shear experiments indicates that the shear strength of a fault responds immediately, and then is followed by a prolonged slip-dependent response, while a set of shock loading experiments indicates that there is no immediate component, and the response is purely gradual and slip-dependent. In our new, high-resolution experiments, we observe that the acoustic transmissivity and dilatancy of simulated faults in our tests respond immediately to changes in the normal stress, consistent with the interpretations of previous investigations, and verify an immediate increase in the area of contact between the roughened sliding surfaces as normal stress increases. However, the shear strength of the fault does not immediately increase, indicating that the new area of contact between the rough fault surfaces does not appear preloaded with any shear resistance or strength. Additional slip is required for the fault to achieve a new shear strength appropriate for its new loading conditions, consistent with previous observations made during shock loading.

  10. Distortion-Product Emissions and Pure-Tone Behavioral Thresholds.

    NASA Astrophysics Data System (ADS)

    Harris, Frances Pauline

    Distortion-product emissions (DPEs) are tonal responses that may be detected in the ear canal when the ear is stimulated simultaneously by two tones that are closely spaced in frequency. In experimental animals, DPEs are reduced in amplitude or are eliminated when cochlear function is disrupted. This association has not been investigated in human subjects. This study was designed to investigate the relation of cochlear status, as determined by pure -tone behavioral thresholds, to DPE amplitude in human subjects. Forty men were selected as subjects. Twenty had normal hearing and 20 had high-frequency sensorineural hearing loss. Pure-tone behavioral thresholds were determined using conventional audiometric procedures for eight frequencies from 750 to 8000 Hz. DPEs were generated in the test ear of each subject by stimulating the ear with two tones, f1 and f2. The stimuli were selected to approximate audiometric test frequencies. Responses were detected by a sensitive microphone that was placed in the ear canal and were extracted by spectral analysis. Results of the study indicated that DPE amplitude was associated with pure-tone threshold. When audiometric threshold was <=10 dB HL, DPEs could be elicited at all test frequencies for 98% of subjects in both groups. Mean maximum emission amplitude ranged from 3 to 13 dB SPL across frequency. When pure-tone threshold was above 50 dB HL, DPEs were absent or were significantly attenuated. DPEs varied in amplitude when audiometric threshold was between these two extremes. The association of DPE amplitude were pure-tone threshold was frequency specific. DPE amplitude was maximal when pure-tone thresholds were <=10 dB HL and decreased as pure-tone behavioral threshold increased in the same subject. Repetition of the DPE protocol with five subjects from each group during separate test sessions indicated that the results were reliable over time. Results of the study have clinical implications. The technique may have potential

  11. 14 CFR 23.337 - Limit maneuvering load factors.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Limit maneuvering load factors. 23.337... Flight Loads § 23.337 Limit maneuvering load factors. (a) The positive limit maneuvering load factor n... not be less than— (1) 0.4 times the positive load factor for the normal utility and...

  12. 14 CFR 23.423 - Maneuvering loads.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Balancing Surfaces § 23.423 Maneuvering loads. Each horizontal surface and its supporting structure, and the...-down pitching conditions is the sum of the balancing loads at V and the specified value of the normal... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Maneuvering loads. 23.423 Section...

  13. 14 CFR 23.423 - Maneuvering loads.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Balancing Surfaces § 23.423 Maneuvering loads. Each horizontal surface and its supporting structure, and the...-down pitching conditions is the sum of the balancing loads at V and the specified value of the normal... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Maneuvering loads. 23.423 Section...

  14. Quantifying the coherence of pure quantum states

    NASA Astrophysics Data System (ADS)

    Chen, Jianxin; Grogan, Shane; Johnston, Nathaniel; Li, Chi-Kwong; Plosker, Sarah

    2016-10-01

    In recent years, several measures have been proposed for characterizing the coherence of a given quantum state. We derive several results that illuminate how these measures behave when restricted to pure states. Notably, we present an explicit characterization of the closest incoherent state to a given pure state under the trace distance measure of coherence. We then use this result to show that the states maximizing the trace distance of coherence are exactly the maximally coherent states. We define the trace distance of entanglement and show that it coincides with the trace distance of coherence for pure states. Finally, we give an alternate proof to a recent result that the ℓ1 measure of coherence of a pure state is never smaller than its relative entropy of coherence.

  15. Dark fermentation on biohydrogen production: Pure culture.

    PubMed

    Lee, Duu-Jong; Show, Kuan-Yeow; Su, Ay

    2011-09-01

    Biohydrogen is regarded as an attractive future clean energy carrier due to its high energy content and environmental-friendly conversion. While biohydrogen production is still in the early stage of development, there have been a variety of laboratory- and pilot-scale systems developed with promising potential. This work presents a review of literature reports on the pure hydrogen-producers under anaerobic environment. Challenges and perspective of biohydrogen production with pure cultures are also outlined.

  16. Long-term stability of normal condition data for novelty detection

    NASA Astrophysics Data System (ADS)

    Manson, Graeme; Pierce, S. Gareth; Worden, Keith; Monnier, Thomas; Guy, Philippe; Atherton, Kathryn

    2000-06-01

    As a technique of diagnosing failure in structures and systems, the method of novelty detection shows considerable merit. The basis of the approach is simple: given measured data from normal condition of the structure, the diagnostic system builds an internal representation of the system normal condition in such a way that subsequent departures from this condition can be identified with confidence in a robust manner. The success or failure of the method is contingent on the accuracy of the description of normal condition. In many cases, the normal condition data may have quite a complex structure: for example, an aircraft may experience a wide range of ambient temperatures in the course of a single flight. Also, the operational loads experienced by the craft as a result of flight manoeuvres may have wide-ranging effects on the measured states. The object of the current paper is to explore the normal condition space for a simple benchmark monitoring system. The said system uses Lamb-wave inspection to diagnose damage in a composite plate. Both short-term and long-term experiments are carried out in order to examine the variations in normal condition as a result of run-in of the instrumentation and variations in ambient temperature. The exercise is not purely academic as the fiber-optic monitoring system is a serious candidate for a practical diagnostic system.

  17. Rehabilitation of pure alexia: A review

    PubMed Central

    Starrfelt, Randi; Ólafsdóttir, Rannveig Rós; Arendt, Ida-Marie

    2013-01-01

    Acquired reading problems caused by brain injury (alexia) are common, either as a part of an aphasic syndrome, or as an isolated symptom. In pure alexia, reading is impaired while other language functions, including writing, are spared. Being in many ways a simple syndrome, one would think that pure alexia was an easy target for rehabilitation efforts. We review the literature on rehabilitation of pure alexia from 1990 to the present, and find that patients differ widely on several dimensions, such as alexia severity and associated deficits. Many patients reported to have pure alexia in the reviewed studies, have associated deficits such as agraphia or aphasia and thus do not strictly conform to the diagnosis. Few studies report clear and generalisable effects of training, none report control data, and in many cases the reported findings are not supported by statistics. We can, however, tentatively conclude that Multiple Oral Re-reading techniques may have some effect in mild pure alexia where diminished reading speed is the main problem, while Tacile-Kinesthetic training may improve letter identification in more severe cases of alexia. There is, however, still a great need for well-designed and controlled studies of rehabilitation of pure alexia. PMID:23808895

  18. Relationship between single-file diffusion of mixed and pure gases in dipeptide nanochannels by high field diffusion NMR.

    PubMed

    Dutta, Akshita R; Sekar, Poorvajan; Dvoyashkin, Muslim; Bowers, Clifford R; Ziegler, Kirk J; Vasenkov, Sergey

    2015-09-01

    High field NMR diffusometry reveals single-file diffusion of CO/CH4 mixture in dipeptide nanochannels with a coincident mobility for CO and CH4. In contrast to the relationship commonly observed for normal diffusion, this mixture mobility is only slightly smaller than that of pure CO which diffuses much faster than pure CH4.

  19. LOADING DEVICE

    DOEpatents

    Ohlinger, L.A.

    1958-10-01

    A device is presented for loading or charging bodies of fissionable material into a reactor. This device consists of a car, mounted on tracks, into which the fissionable materials may be placed at a remote area, transported to the reactor, and inserted without danger to the operating personnel. The car has mounted on it a heavily shielded magazine for holding a number of the radioactive bodies. The magazine is of a U-shaped configuration and is inclined to the horizontal plane, with a cap covering the elevated open end, and a remotely operated plunger at the lower, closed end. After the fissionable bodies are loaded in the magazine and transported to the reactor, the plunger inserts the body at the lower end of the magazine into the reactor, then is withdrawn, thereby allowing gravity to roll the remaining bodies into position for successive loading in a similar manner.

  20. Carbohydrate Loading.

    ERIC Educational Resources Information Center

    Csernus, Marilyn

    Carbohydrate loading is a frequently used technique to improve performance by altering an athlete's diet. The objective is to increase glycogen stored in muscles for use in prolonged strenuous exercise. For two to three days, the athlete consumes a diet that is low in carbohydrates and high in fat and protein while continuing to exercise and…

  1. Engineering arbitrary pure and mixed quantum states

    SciTech Connect

    Pechen, Alexander

    2011-10-15

    Controlled manipulation by atomic- and molecular-scale quantum systems has attracted a lot of research attention in recent years. A fundamental problem is to provide deterministic methods for controlled engineering of arbitrary quantum states. This work proposes a deterministic method for engineering arbitrary pure and mixed states of a wide class of quantum systems. The method exploits a special combination of incoherent and coherent controls (incoherent and coherent radiation) and has two properties which are specifically important for manipulating by quantum systems: it realizes the strongest possible degree of their state control, complete density matrix controllability, meaning the ability to steer arbitrary pure and mixed initial states into any desired pure or mixed final state, and it is all-to-one, such that each particular control transfers all initial system states into one target state.

  2. Pure neuritic leprosy: Current status and relevance.

    PubMed

    Rao, P Narasimha; Suneetha, Sujai

    2016-01-01

    Pure neuritic leprosy has always been an enigma due to its clinical and management ambiguities. Although only the Indian Association of Leprologist's classification recognizes 'pure neuritic leprosy' as a distinct sub group of leprosy, cases nonetheless are reported from various countries of Asia, Africa, South America and Europe, indicating its global relevance. It is important to maintain pure neuritic leprosy as a subgroup as it constitutes a good percentage of leprosy cases reported from India, which contributes to more than half of global leprosy numbers. Unfortunately, a high proportion of these patients present with Grade 2 disability at the time of initial reporting itself due to the early nerve involvement. Although skin lesions are absent by definition, when skin biopsies were performed from the skin along the distribution of the affected nerve, a proportion of patients demonstrated leprosy pathology, revealing sub-clinical skin involvement. In addition on follow-up, skin lesions are noted to develop in up to 20% of pure neuritic leprosy cases, indicating its progression to manifest cutaneous disease. Over the decades, the confirmation of diagnosis of pure neuritic leprosy has been subjective, however, with the arrival and use of high-resolution ultrasonography (HRUS) for nerve imaging, we have a tool not only to objectively measure and record the nerve thickening but also to assess the morphological alterations in the nerve including echo texture, fascicular pattern and vascularity. Management of pure neuritic leprosy requires multidrug therapy along with appropriate dose of systemic corticosteroids, for both acute and silent neuritis. Measures for pain relief, self-care of limbs and physiotherapy are important to prevent as well as manage disabilities in this group of patients. PMID:27088926

  3. Pure Apraxia of Speech - A Case Report -

    PubMed Central

    Kang, Young Ae; Yun, Sang Jin

    2011-01-01

    Apraxia of speech (AOS) is the impairment of motor programming. However, the exact nature of this deficit remains unclear. In particular, AOS without other speech-language deficit is called pure AOS, but it is very rare. When diagnosing AOS, the characteristic of articulation is considered a crucial criterion, which has been proposed for differentiating AOS from phonological and dysarthric disorders. The present study reports on pure AOS in a 37-year-old right-handed male after a left insular, front, temporal infarction. This report may be useful for further AOS study and diagnosis in the clinical setting. PMID:22506197

  4. BRST and the pure spinor formalism

    SciTech Connect

    Garcia, J. Antonio

    2008-03-06

    The aim of this talk is to show the relation between the standard BRST approach of the GS superstring with the quantization technics used in the pure spinor approach to superstring. To that end we will use the Batalin-Fradkin-Tyutin (BFT) conversion program of second class constraints to first class constraints in the GS superstring using light cone coordinates. By applying this systematic procedure we were able to obtain a gauge system that is equivalent to the recent model proposed in [1] to relate the GS superstring to the pure spinor formalism.

  5. Viral load, E2 gene disruption status, and lineage of human papillomavirus type 16 infection in cervical neoplasia.

    PubMed

    Cheung, Jo L K; Lo, Keith W K; Cheung, Tak-Hong; Tang, Julian W; Chan, Paul K S

    2006-12-15

    The clinical utility of human papillomavirus (HPV) load and integration status remains unclear. We applied refined methods to delineate the viral load, integration status, and lineage of 104 women with HPV-16 monotype infection, including 19 with normal cervices, 9 with histologically proven cervical intraepithelial neoplasia (CIN) 1, 24 with CIN 2, 27 with CIN 3, and 25 with squamous cell carcinoma (SCC). Higher crude viral load, as determined by real-time polymerase chain reaction (PCR) targeting the E7 gene, was observed for SCC but became insignificant after normalization for cell content. Integration was located and quantified by real-time PCRs targeting, respectively, the carboxyl, amino, and hinge domains of the E2 gene. Pure episomal, integrated, and mixed forms were observed in all disease groups. Most E2 gene disruptions involved the amino-terminal, but sparing the hinge region that has been frequently used as a surrogate marker of integration. Large-fragment disruption involving all 3 E2 regions was observed only in the CIN 3 and SCC groups. Altogether, 33.3% of the CIN 3 group and 28.0% of the SCC group harbored pure episomal genomes. The Asian lineage was associated with a higher risk for CIN 3/SCC than the European lineage, and 6 of the 7 large-fragment E2 disruptions were from Asian lineage. The link between viral lineage, integration pattern, and oncogenesis deserves further study.

  6. LOADED WAVEGUIDES

    DOEpatents

    Mullett, L.B.; Loach, B.G.; Adams, G.L.

    1958-06-24

    >Loaded waveguides are described for the propagation of electromagnetic waves with reduced phase velocities. A rectangular waveguide is dimensioned so as to cut-off the simple H/sub 01/ mode at the operating frequency. The waveguide is capacitance loaded, so as to reduce the phase velocity of the transmitted wave, by connecting an electrical conductor between directly opposite points in the major median plane on the narrower pair of waveguide walls. This conductor may take a corrugated shape or be an aperature member, the important factor being that the electrical length of the conductor is greater than one-half wavelength at the operating frequency. Prepared for the Second U.N. International ConferThe importance of nuclear standards is duscussed. A brief review of the international callaboration in this field is given. The proposal is made to let the International Organization for Standardization (ISO) coordinate the efforts from other groups. (W.D.M.)

  7. Spinning Reserve from Responsive Load

    SciTech Connect

    Kueck, John D; Kirby, Brendan J; Laughner, T; Morris, K

    2009-01-01

    As power system costs rise and capacity is strained demand response can provide a significant system reliability benefit at a potentially attractive cost. The 162 room Music Road Hotel in Pigeon Forge Tennessee agreed to host a spinning reserve test. The Tennessee Valley Authority (TVA) supplied real-time metering and monitoring expertise to record total hotel load during both normal operations and testing. Preliminary testing showed that hotel load can be curtailed by 22% to 37% depending on the outdoor temperature and the time of day. The load drop was very rapid, essentially as fast as the 2 second metering could detect.

  8. Pure agraphia after deep left hemisphere haematoma.

    PubMed Central

    Croisile, B; Laurent, B; Michel, D; Trillet, M

    1990-01-01

    Pure agraphia is reported following haematoma in the left centrum semiovale sparing both parietal and frontal cortices. There was total inability to produce graphemes in the absence of limb apraxia. The lesion is assumed to have prevented linguistic and graphemic systems from gaining access to the frontal motor programme. Images PMID:2324759

  9. A fatal case of pure metaphyseal chondroblastoma.

    PubMed

    Binesh, Fariba; Moghadam, Reza Nafisi; Abrisham, Jalil

    2013-08-23

    The chondroblastoma (CB) is a rare cartilaginous tumour; it represents less than 1% of all bone tumours. It is mostly localised at the level of the epiphysis of long bones. We report a fatal case of pure metaphyseal CB of the tibia in a 9-year-old boy whose pulmonary metastases developed soon after operative therapy of the primary tumour.

  10. Temporal Ventriloquism in a Purely Temporal Context

    ERIC Educational Resources Information Center

    Hartcher-O'Brien, Jessica; Alais, David

    2011-01-01

    This study examines how audiovisual signals are combined in time for a temporal analogue of the ventriloquist effect in a purely temporal context, that is, no spatial grounding of signals or other spatial facilitation. Observers were presented with two successive intervals, each defined by a 1250-ms tone, and indicated in which interval a brief…

  11. A fatal case of pure metaphyseal chondroblastoma.

    PubMed

    Binesh, Fariba; Moghadam, Reza Nafisi; Abrisham, Jalil

    2013-01-01

    The chondroblastoma (CB) is a rare cartilaginous tumour; it represents less than 1% of all bone tumours. It is mostly localised at the level of the epiphysis of long bones. We report a fatal case of pure metaphyseal CB of the tibia in a 9-year-old boy whose pulmonary metastases developed soon after operative therapy of the primary tumour. PMID:23975916

  12. Implicit Reading in Chinese Pure Alexia

    ERIC Educational Resources Information Center

    Shan, Chunlei; Zhu, Renjing; Xu, Mingwei; Luo, Benyan; Weng, Xuchu

    2010-01-01

    A number of recent studies have shown that some patients with pure alexia display evidence of implicit access to lexical and semantic information about words that they cannot read explicitly. This phenomenon has not been investigated systematically in Chinese patients. We report here a case study of a Chinese patient who met the criteria for pure…

  13. Pure science and the problem of progress.

    PubMed

    Douglas, Heather

    2014-06-01

    How should we understand scientific progress? Kuhn famously discussed science as its own internally driven venture, structured by paradigms. He also famously had a problem describing progress in science, as problem-solving ability failed to provide a clear rubric across paradigm change--paradigm changes tossed out problems as well as solving them. I argue here that much of Kuhn's inability to articulate a clear view of scientific progress stems from his focus on pure science and a neglect of applied science. I trace the history of the distinction between pure and applied science, showing how the distinction came about, the rhetorical uses to which the distinction has been put, and how pure science came to be both more valued by scientists and philosophers. I argue that the distinction between pure and applied science does not stand up to philosophical scrutiny, and that once we relinquish it, we can provide Kuhn with a clear sense of scientific progress. It is not one, though, that will ultimately prove acceptable. For that, societal evaluations of scientific work are needed.

  14. A Pure Theory of Lifelong Learning.

    ERIC Educational Resources Information Center

    Hatton, Michael J.

    Charles Tiebout's Pure Theory of Local Expenditures serves as a helpful framework in examining the emergence of the learning society, communications technologies, freer trade, and the effects these will have on the educational infrastructure. Tiebout argued that the failure of market-type systems of public good at the central government level does…

  15. Exploring the simplest purely baryonic decay processes

    NASA Astrophysics Data System (ADS)

    Geng, C. Q.; Hsiao, Y. K.; Rodrigues, Eduardo

    2016-07-01

    Though not considered in general, purely baryonic decays could shed light on the puzzle of the baryon number asymmetry in the universe by means of a better understanding of the baryonic nature of our matter world. As such, they constitute a yet unexplored class of decay processes worth investigating. We propose to search for purely baryonic decay processes at the LHCb experiment. No such type of decay has ever been observed. In particular, we concentrate on the decay Λb0→p p ¯n , which is the simplest purely baryonic decay mode, with solely spin-1 /2 baryons involved. We predict its decay branching ratio to be B (Λb0→p p ¯ n )=(2. 0-0.2+0.3)×10-6 , which is sufficiently large to make the decay mode accessible to LHCb. Our study can be extended to other purely baryonic decays such as Λb0→p p ¯ Λ , Λb0→Λ p ¯ Λ , and Λb0→Λ Λ ¯Λ , as well as to similar decays of antitriplet b baryons such as Ξb0 ,-.

  16. Fundamental Flame Velocities of Pure Hydrocarbons I : Alkanes, Alkenes, Alkynes Benzene, and Cyclohexane

    NASA Technical Reports Server (NTRS)

    Gerstein, Melvin; Levine, Oscar; Wong, Edgar L

    1950-01-01

    The flame velocities of 37 pure hydrocarbons including normal and branched alkanes, alkenes, and alkynes; as well as benzene and cyclohexane, together with the experimental technique employed are presented. The normal alkanes have about the same flame velocity from ethane through heptane with methane being about 16 percent lower. Unsaturation increases the flame velocity in the order of alkanes, alkenes, and alkynes. Branching reduces the flame velocity.

  17. 14 CFR 23.525 - Application of loads.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23.525... from the load factors prescribed in § 23.527, the loads may be distributed over the hull or main float bottom (in order to avoid excessive local shear loads and bending moments at the location of water...

  18. 14 CFR 23.391 - Control surface loads.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Control surface loads. 23.391 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Control Surface and System Loads § 23.391 Control surface loads. The control surface loads specified in §§...

  19. Modelling Normal and Impaired Letter Recognition: Implications for Understanding Pure Alexic Reading

    ERIC Educational Resources Information Center

    Chang, Ya-Ning; Furber, Steve; Welbourne, Stephen

    2012-01-01

    Letter recognition is the foundation of the human reading system. Despite this, it tends to receive little attention in computational modelling of single word reading. Here we present a model that can be trained to recognise letters in various spatial transformations. When presented with degraded stimuli the model makes letter confusion errors…

  20. TMED-4 INTERIM REPORT PURE ZR EQUILIBRIUM TEST RESULTS

    SciTech Connect

    Korinko, P.; Morgan, G.

    2010-12-17

    Due to higher than expected permeation rates in the production of tritium in the TVA, a development and testing program was implemented to develop the understanding of why the higher rates were occurring. In addition, improved data are needed for both the design as well as the predictive models. One part of the program was to determine the equilibrium pressure of hydrogen and tritium over NPZ (1). During the course of this testing, some curious results were discovered (2) compared to the published literature data (3). Due to these apparently results, a follow-on task was undertaken to determine the equilibrium pressure of protium and deuterium over pure zirconium. A series of experiments were conducted to determine equilibrium pressures and isotherm data for the zirconium - protium and zirconium - deuterium systems. The data match the published literature data reasonably well with the plateau extending to loadings of about 1.4. There is a significant pressure rise for loadings greater than 1.7.

  1. Friction and anchorage loading revisited.

    PubMed

    Dholakia, Kartik D

    2012-01-01

    Contemporary concepts of sliding mechanics explain that friction is inevitable. To overcome this frictional resistance, excess force is required to retract the tooth along the archwire (ie, individual retraction of canines, en masse retraction of anterior teeth), in addition to the amount of force required for tooth movement. The anterior tooth retraction force, in addition to excess force (to overcome friction), produces reciprocal protraction force on molars, thereby leading to increased anchorage loading. However, this traditional concept was challenged in recent literature, which was based on the finite element model, but did not bear correlation to the clinical scenario. This article will reinforce the fact that clinically, friction increases anchorage loading in all three planes of space, considering the fact that tooth movement is a quasistatic process rather than a purely continuous or static one, and that conventional ways of determining the effects of static or dynamic friction on anchorage load cannot be applied to clinical situations (which consist of anatomical resistance units and a complex muscular force system). The article does not aim to quantify friction and its effect on the amount of anchorage load. Rather, a new perspective regarding the role of various additional factors (which is not explained by contemporary concept) that may influence friction and anchorage loading is provided..

  2. Pure menstrual migraine with sensory aura: a case report.

    PubMed

    Chen, Jiann-Jy; Hsu, Yung-Chu; Chen, Dem-Lion

    2012-07-01

    Hormonal changes related to the menstrual cycle have a great impact on migraines in women. Menstrual migraine attacks are almost invariably without aura. Categorizing migraines into menstrual or non-menstrual types is one way to stratify migraines without aura according to the appendix criteria of the International Classification of Headache Disorders. We report a peri-menopausal woman whose sensory aura exclusively heralded menstrual migraine. A 51-year-old woman had suffered from monthly episodic headaches since the age of 46. Before a headache, and within 1 h on the first day of her menstruation, she always experienced numbness in her entire left upper limb. After the sensory aura, migrainous headaches occurred with nausea and photophobia. In the postmenopausal period, she no longer had sensory aura, and her headache pattern changed and became less severe. Her physical and neurologic exams as well as electroencephalography, brain magnetic resonance imaging, and conventional angiography were all normal. She fulfilled the diagnosis of pure menstrual migraine with typical sensory aura. To our knowledge, this is the first formal case report of pure menstrual migraine with aura.

  3. Heat engine driven by purely quantum information.

    PubMed

    Park, Jung Jun; Kim, Kang-Hwan; Sagawa, Takahiro; Kim, Sang Wook

    2013-12-01

    The key question of this Letter is whether work can be extracted from a heat engine by using purely quantum mechanical information. If the answer is yes, what is its mathematical formula? First, by using a bipartite memory we show that the work extractable from a heat engine is bounded not only by the free energy change and the sum of the entropy change of an individual memory but also by the change of quantum mutual information contained inside the memory. We then find that the engine can be driven by purely quantum information, expressed as the so-called quantum discord, forming a part of the quantum mutual information. To confirm it, as a physical example we present the Szilard engine containing a diatomic molecule with a semipermeable wall.

  4. Pure field theories and MACSYMA algorithms

    NASA Technical Reports Server (NTRS)

    Ament, W. S.

    1977-01-01

    A pure field theory attempts to describe physical phenomena through singularity-free solutions of field equations resulting from an action principle. The physics goes into forming the action principle and interpreting specific results. Algorithms for the intervening mathematical steps are sketched. Vacuum general relativity is a pure field theory, serving as model and providing checks for generalizations. The fields of general relativity are the 10 components of a symmetric Riemannian metric tensor; those of the Einstein-Straus generalization are the 16 components of a nonsymmetric. Algebraic properties are exploited in top level MACSYMA commands toward performing some of the algorithms of that generalization. The light cone for the theory as left by Einstein and Straus is found and simplifications of that theory are discussed.

  5. Symmetries of Type N Pure Radiation Fields

    NASA Astrophysics Data System (ADS)

    Ahsan, Zafar; Ali, Musavvir

    2015-05-01

    The geometrical symmetries corresponding to the continuous groups of collineations and motions generated by a null vector l are considered. These symmetries have been translated into the language of Newman-Penrose formalism for pure radiation (PR) type N fields. It is seen that for such fields, conformal, special conformal and homothetic motions degenerate to motion. The concept of free curvature, matter curvature and matter affine collineations have been discussed and the conditions under which PR type N fields admit such collineations have been obtained. Moreover, it is shown that the projective collineation degenerate to matter affine, special projective, conformal, special conformal, null geodesic and special null geodesic collineations. It is also seen that type N pure radiation fields admit Maxwell collineation along the propagation vector l.

  6. Grip for fatigue testing pure aluminium

    NASA Astrophysics Data System (ADS)

    Lehmann, P.; Yuan, G. S.; Hartwig, K. T.

    A simple method of clamping pure aluminium for fatigue tests at cryogenic temperatures is described. Easily machined cylindrical specimens are aligned and held firmly by collet grips that counteract sample shrinkage during cooldown. Specimens are quickly mounted and removed after testing without distortion or thermal treatment 99.999% aluminium, aluminium alloys and copper were gripped successfully through tens of thousands of fully reversed tension-compression cycles at 295, 77 and 4.2 K.

  7. Pure connection action principle for general relativity.

    PubMed

    Krasnov, Kirill

    2011-06-24

    It has already been known for two decades that general relativity can be reformulated as a certain gauge theory, so that the only dynamical field is an SO(3) connection and the spacetime metric appears as a derived object. However, no simple action principle realizing these ideas has been available. A new elegant action principle for such a "pure connection" formulation of GR is described.

  8. Stable freestanding thin films of pure water

    SciTech Connect

    Weon, B. M.; Je, J. H.; Hwu, Y.; Margaritondo, G.

    2008-03-10

    Obtaining water microstructures is very difficult because of low viscosity and high surface tension. We produced stable freestanding thin films of pure water by x-ray bombardment of small liquid volumes in capillary tubes. A detailed characterization with phase-contrast radiology demonstrated a lifetime beyond 1 h with no chemical stabilizer for micron-thickness films with half-millimeter-level diameter. This can be attributed to the interplay of two x-ray effects: water evaporation and surface charging.

  9. The effects of load magnitude and lifting speed on the kinematic data of load and human posture.

    PubMed

    Lee, Tzu-Hsien

    2015-01-01

    This study examined the effects of load magnitude and lifting speed on the kinematic data of load and human posture in a lifting task. Three load magnitudes (10, 20 and 30 kg) and three lifting speeds (fast, normal and slow) were examined in this study. This study showed that participants shortened the load acceleration period on lifting a lighter load than on lifting a heavier load. For normal and slow lifting speeds, participants moved and lifted the load closer to their body when lifting a heavy load. Participants tended to maintain their postures by using an ankle strategy when in heavier load or faster lifting conditions. The profiles of angle velocity of knee and ankle joints demonstrated the important role of the lower extremities in the acceleration of the load in the initial stage of fast lifting. In addition, participants could not easily control the momentum transmitted to the ankle joint for lifting the heavy load.

  10. Acquired pure red cell aplasia: updated review of treatment

    PubMed Central

    Sawada, Kenichi; Fujishima, Naohito; Hirokawa, Makoto

    2008-01-01

    Pure red cell aplasia (PRCA) is a syndrome characterized by a severe normocytic anaemia, reticulocytopenia, and absence of erythroblasts from an otherwise normal bone marrow. Primary PRCA, or secondary PRCA which has not responded to treatment of the underlying disease, is treated as an immunologically-mediated disease. Although vigorous immunosuppressive treatments induce and maintain remissions in a majority of patients, they carry an increased risk of serious complications. Corticosteroids were used in the treatment of PRCA and this has been considered the treatment of first choice although relapse is not uncommon. Cyclosporine A (CsA) has become established as one of the leading drugs for treatment of PRCA. However, common concerns have been the number of patients treated with CsA who achieve sustained remissions and the number that relapse. This article reviews the current status of CsA therapy and compares it to other treatments for diverse PRCAs. PMID:18510682

  11. Modularity of music: evidence from a case of pure amusia

    PubMed Central

    Piccirilli, M.; Sciarma, T.; Luzzi, S.

    2000-01-01

    A case of pure amusia in a 20 year old left handed non-professional musician is reported. The patient showed an impairment of music abilities in the presence of normal processing of speech and environmental sounds. Furthermore, whereas recognition and production of melodic sequences were grossly disturbed, both the recognition and production of rhythm patterns were preserved. This selective breakdown pattern was produced by a focal lesion in the left superior temporal gyrus. This case thus suggests that not only linguistic and musical skills, but also melodic and rhythmic processing are independent of each other. This functional dissociation in the musical domain supports the hypothesis that music components have a modular organisation. Furthermore, there is the suggestion that amusia may be produced by a lesion located strictly in one hemisphere and that the superior temporal gyrus plays a crucial part in melodic processing.

 PMID:10990522

  12. On constructing purely affine theories with matter

    NASA Astrophysics Data System (ADS)

    Cervantes-Cota, Jorge L.; Liebscher, D.-E.

    2016-08-01

    We explore ways to obtain the very existence of a space-time metric from an action principle that does not refer to it a priori. Although there are reasons to believe that only a non-local theory can viably achieve this goal, we investigate here local theories that start with Schrödinger's purely affine theory (Schrödinger in Space-time structure. Cambridge UP, Cambridge, 1950), where he gave reasons to set the metric proportional to the Ricci curvature aposteriori. When we leave the context of unified field theory, and we couple the non-gravitational matter using some weak equivalence principle, we can show that the propagation of shock waves does not define a lightcone when the purely affine theory is local and avoids the explicit use of the Ricci tensor in realizing the weak equivalence principle. When the Ricci tensor is substituted for the metric, the equations seem to have only a very limited set of solutions. This backs the conviction that viable purely affine theories have to be non-local.

  13. Graphical calculus for Gaussian pure states

    SciTech Connect

    Menicucci, Nicolas C.; Flammia, Steven T.; Loock, Peter van

    2011-04-15

    We provide a unified graphical calculus for all Gaussian pure states, including graph transformation rules for all local and semilocal Gaussian unitary operations, as well as local quadrature measurements. We then use this graphical calculus to analyze continuous-variable (CV) cluster states, the essential resource for one-way quantum computing with CV systems. Current graphical approaches to CV cluster states are only valid in the unphysical limit of infinite squeezing, and the associated graph transformation rules only apply when the initial and final states are of this form. Our formalism applies to all Gaussian pure states and subsumes these rules in a natural way. In addition, the term 'CV graph state' currently has several inequivalent definitions in use. Using this formalism we provide a single unifying definition that encompasses all of them. We provide many examples of how the formalism may be used in the context of CV cluster states: defining the 'closest' CV cluster state to a given Gaussian pure state and quantifying the error in the approximation due to finite squeezing; analyzing the optimality of certain methods of generating CV cluster states; drawing connections between this graphical formalism and bosonic Hamiltonians with Gaussian ground states, including those useful for CV one-way quantum computing; and deriving a graphical measure of bipartite entanglement for certain classes of CV cluster states. We mention other possible applications of this formalism and conclude with a brief note on fault tolerance in CV one-way quantum computing.

  14. Making sense of peak load cost allocations

    SciTech Connect

    Power, T.M.

    1995-03-15

    When it comes to cost allocation, common wisdom assigns costs in proportion to class contributions to peak loads, The justification is simple: Since the equipment had to be sized to meet peak day loads, those costs should be allocated on the same basis. Many different peak allocators have been developed on this assumption: single coincident peak contribution, sum of coincident peaks, noncoincident peak, average and excess demand, peak and average demand, base and extra capacity, and so on. Such pure peak-load allocators may not be politically acceptable, but conceptually, at least, they appear to offer the only defensible approach. Nevertheless, where capacity can be added with significant economies of scale, making cost allocations in proportion to peak loads violates well-known relationships between economics and engineering. What is missing is any tracing of the way in which the peak-load design criteria actually influence the cost incurred.

  15. Combined mechanical loading of composite tubes

    NASA Technical Reports Server (NTRS)

    Derstine, Mark S.; Pindera, Marek-Jerzy; Bowles, David E.

    1988-01-01

    An analytical/experimental investigation was performed to study the effect of material nonlinearities on the response of composite tubes subjected to combined axial and torsional loading. The effect of residual stresses on subsequent mechanical response was included in the investigation. Experiments were performed on P75/934 graphite-epoxy tubes with a stacking sequence of (15/0/ + or - 10/0/ -15), using pure torsion and combined axial/torsional loading. In the presence of residual stresses, the analytical model predicted a reduction in the initial shear modulus. Experimentally, coupling between axial loading and shear strain was observed in laminated tubes under combined loading. The phenomenon was predicted by the nonlinear analytical model. The experimentally observed linear limit of the global shear response was found to correspond to the analytically predicted first ply failure. Further, the failure of the tubes was found to be path dependent above a critical load level.

  16. RTLS entry load relief parameter optimization

    NASA Technical Reports Server (NTRS)

    Crull, T. J.

    1975-01-01

    The results are presented of a study of a candidate load relief control law for use during the pullup phase of Return-to-Launch-Site (RTLS) abort entries. The control law parameters and cycle time which optimized performance of the normal load factor limiting phase (load relief phase) of an RTLS entry are examined. A set of control law gains, a smoothing parameter, and a normal force coefficient curve fit are established which resulted in good load relief performance considering the possible aerodynamic coefficient uncertainties defined. Also, the examination of various guidance cycle times revealed improved load relief performance with decreasing cycle time. A .5 second cycle provided smooth and adequate load relief in the presence of all the aerodynamic uncertainties examined.

  17. The Fatigue Behavior of Built-Up Welded Beams of Commercially Pure Titanium

    NASA Astrophysics Data System (ADS)

    Patnaik, Anil; Poondla, Narendra; Bathini, Udaykar; Srivatsan, T. S.

    2011-10-01

    In this article, the results of a recent study aimed at evaluating, understanding, and rationalizing the extrinsic influence of fatigue loading on the response characteristics of built-up welded beams made from commercially pure titanium (Grade 2) are presented and discussed. The beams were made from welding plates and sheets of titanium using the pulsed gas metal arc welding technique to form a structural beam having an I-shaped cross section. The welds made for the test beams of the chosen metal were fillet welds using a matching titanium filler metal wire. The maximum and minimum load values at which the built-up beams were cyclically deformed were chosen to be within the range of 22-45% of the maximum predicted flexural static load. The beams were deformed in fatigue at a stress ratio of 0.1 and constant frequency of 5 Hz. The influence of the ratio of maximum load with respect to the ultimate failure load on fatigue performance, quantified in terms of fatigue life, was examined. The percentage of maximum load to ultimate load that resulted in run-out of one million cycles was established. The overall fracture behavior of the failed beam sample was characterized by scanning electron microscopy observations to establish the conjoint influence of load severity, intrinsic microstructural effects, and intrinsic fracture surface features in governing failure by fracture.

  18. Normal Pressure Hydrocephalus

    MedlinePlus

    ... Enhancing Diversity Find People About NINDS NINDS Normal Pressure Hydrocephalus Information Page Synonym(s): Hydrocephalus - Normal Pressure Table ... Español Additional resources from MedlinePlus What is Normal Pressure Hydrocephalus? Normal pressure hydrocephalus (NPH) is an abnormal ...

  19. Trace element load in cancer and normal lung tissue

    NASA Astrophysics Data System (ADS)

    Kubala-Kukuś , A.; Braziewicz, J.; Banaś , D.; Majewska, U.; Góź Dź , S.; Urbaniak, A.

    1999-04-01

    Samples of malignant and benign human lung tissues were analysed by two complementary methods, i.e., particle induced X-ray emission (PIXE) and total reflection X-ray fluorescence (TRXRF). The concentration of trace elements of P, S, K, Ca, Ti, Cr, Mn, Fe, Cu, Zn, Se, Sr, Hg and Pb was determined in squamous cancer of lung tissue from 65 people and in the benign lung tumour tissue from 5 people. Several elements shows enhancement in cancerous lung tissue of women in comparison to men, i.e., titanium show maximum enhancement by 48% followed by Cr (20%) and Mn (36%). At the same time trace element concentration of Sr and Pb are declaimed by 30% and 20% in women population. Physical basis of used analytical methods, experimental set-up and the procedure of sample preparation are described.

  20. Enhanced Estimation of Terrestrial Loadings for TMDLs: Normalization Approach

    Technology Transfer Automated Retrieval System (TEKTRAN)

    TMDL implementation plans to remediate pathogen-impaired streams are usually based on deterministic terrestrial fate and transport (DTFT) models. A novel protocol is proposed that can effectively, efficiently, and explicitly capture the predictive uncertainty of DTFT models used to establish terres...

  1. Cervical and thoracic spine injury from interactions with vehicle roofs in pure rollover crashes.

    PubMed

    Bambach, M R; Grzebieta, R H; McIntosh, A S; Mattos, G A

    2013-01-01

    Around one third of serious injuries sustained by belted, non-ejected occupants in pure rollover crashes occur to the spine. Dynamic rollover crash test methodologies have been established in Australia and the United States, with the aims of understanding injury potential in rollovers and establishing the basis of an occupant rollover protection crashworthiness test protocol that could be adopted by consumer new car assessment programmes and government regulators internationally. However, for any proposed test protocol to be effective in reducing the high trauma burden resulting from rollover crashes, appropriate anthropomorphic devices that replicate real-world injury mechanisms and biomechanical loads are required. To date, consensus regarding the combination of anthropomorphic device and neck injury criteria for rollover crash tests has not been reached. The aim of the present study is to provide new information pertaining to the nature and mechanisms of spine injury in pure rollover crashes, and to assist in the assessment of spine injury potential in rollover crash tests. Real-world spine injury cases that resulted from pure rollover crashes in the United States between 2000 and 2009 are identified, and compared with cadaver experiments under vertical load by other authors. The analysis is restricted to contained, restrained occupants that were injured from contact with the vehicle roof structure during a pure rollover, and the role of roof intrusion in creating potential for spine injury is assessed. Recommendations for assessing the potential for spine injury in rollover occupant protection crash test protocols are made. PMID:23149322

  2. The deformation behavior of commercially pure titanium subjected to electron beam treatment

    SciTech Connect

    Kazachenok, Marina Kozelskaya, Anna; Panin, Alexey; Ivanov, Yurii

    2015-10-27

    The effect of low-energy high-current pulsed electron beam treatment on the microstructure and mechanical properties of commercially pure titanium specimens is studied. Plastic deformation mechanisms of the specimens subjected to the electron beam treatment followed by uniaxial tension are demonstrated. The role of the interface between the hardened surface layer and the relatively soft parent metal in the slip band formation in the loaded specimens is revealed.

  3. The deformation behavior of commercially pure titanium subjected to electron beam treatment

    NASA Astrophysics Data System (ADS)

    Kazachenok, Marina; Panin, Alexey; Kozelskaya, Anna; Ivanov, Yurii

    2015-10-01

    The effect of low-energy high-current pulsed electron beam treatment on the microstructure and mechanical properties of commercially pure titanium specimens is studied. Plastic deformation mechanisms of the specimens subjected to the electron beam treatment followed by uniaxial tension are demonstrated. The role of the interface between the hardened surface layer and the relatively soft parent metal in the slip band formation in the loaded specimens is revealed.

  4. Augmenting The HST Pure Parallel Observations

    NASA Astrophysics Data System (ADS)

    Patterson, Alan; Soutchkova, G.; Workman, W.

    2012-05-01

    Pure Parallel (PP) programs, designated GO/PAR, are a subgroup of General Observer (GO) programs. PP execute simultaneously with prime GO observations to which they are "attached". The PP observations can be performed with ACS/WFC, WFC3/UVIS or WFC3/IR and can be attached only to GO visits in which the instruments are either COS or STIS. The current HST Parallel Observation Processing System (POPS) was introduced after the Servicing Mission 4. It increased the HST productivity by 10% in terms of the utilization of HST prime orbits and was highly appreciated by the HST observers, allowing them to design efficient, multi-orbit survey projects for collecting large amounts of data on identifiable targets. The results of the WFC3 Infrared Spectroscopic Parallel Survey (WISP), Hubble Infrared Pure Parallel Imaging Extragalactic Survey (HIPPIES), and The Brightest-of-Reionizing Galaxies Pure Parallel Survey (BoRG) exemplify this benefit. In Cycle 19, however, the full advantage of GO/PARs came under risk. Whereas each of the previous cycles provided over one million seconds of exposure time for PP, in Cycle 19 that number reduced to 680,000 seconds. This dramatic decline occurred because of fundamental changes in the construction of COS prime observations. To preserve the science output of PP, the PP Working Group was tasked to find a way to recover the lost time and maximize the total time available for PP observing. The solution was to expand the definition of a PP opportunity to allow PP exposures to span one or more primary exposure readouts. So starting in HST Cycle 20, PP opportunities will no longer be limited to GO visits with a single uninterrupted exposure in an orbit. The resulting enhancements in HST Cycle 20 to the PP opportunity identification and matching process are expected to restore the PP time to previously achieved and possibly even greater levels.

  5. chemf: A purely functional chemistry toolkit

    PubMed Central

    2012-01-01

    Background Although programming in a type-safe and referentially transparent style offers several advantages over working with mutable data structures and side effects, this style of programming has not seen much use in chemistry-related software. Since functional programming languages were designed with referential transparency in mind, these languages offer a lot of support when writing immutable data structures and side-effects free code. We therefore started implementing our own toolkit based on the above programming paradigms in a modern, versatile programming language. Results We present our initial results with functional programming in chemistry by first describing an immutable data structure for molecular graphs together with a couple of simple algorithms to calculate basic molecular properties before writing a complete SMILES parser in accordance with the OpenSMILES specification. Along the way we show how to deal with input validation, error handling, bulk operations, and parallelization in a purely functional way. At the end we also analyze and improve our algorithms and data structures in terms of performance and compare it to existing toolkits both object-oriented and purely functional. All code was written in Scala, a modern multi-paradigm programming language with a strong support for functional programming and a highly sophisticated type system. Conclusions We have successfully made the first important steps towards a purely functional chemistry toolkit. The data structures and algorithms presented in this article perform well while at the same time they can be safely used in parallelized applications, such as computer aided drug design experiments, without further adjustments. This stands in contrast to existing object-oriented toolkits where thread safety of data structures and algorithms is a deliberate design decision that can be hard to implement. Finally, the level of type-safety achieved by Scala highly increased the reliability of our code

  6. Composite Materials and Meta Materials for a New Approach to ITER ICRH Loads

    SciTech Connect

    Bottollier-Curtet, H.; Argouarch, A.; Vulliez, K.; Becoulet, A.; Litaudon, X.; Magne, R.; Champeaux, S.; Gouard, Ph.; Primout, M.; Le Gallou, J.-H.

    2009-11-26

    Preliminary laboratory testing of ICRH antennas is a very useful step before their commissioning. Traditionally, pure water, salt water or baking soda water loads are used. These 'water' loads are convenient but strongly limited in terms of performance testing. We have started two feasibility studies for advanced ICRH loads made of ferroelectric ceramics (passive loads) and meta materials (active loads). Preliminary results are very encouraging.

  7. Composite Materials and Meta Materials for a New Approach to ITER ICRH Loads

    NASA Astrophysics Data System (ADS)

    Bottollier-Curtet, H.; Argouarch, A.; Champeaux, S.; Gouard, Ph.; Le Gallou, J.-H.; Primout, M.; Vulliez, K.; Bécoulet, A.; Litaudon, X.; Magne, R.

    2009-11-01

    Preliminary laboratory testing of ICRH antennas is a very useful step before their commissioning. Traditionally, pure water, salt water or baking soda water loads are used. These "water" loads are convenient but strongly limited in terms of performance testing. We have started two feasibility studies for advanced ICRH loads made of ferroelectric ceramics (passive loads) and meta materials (active loads) [1]. Preliminary results are very encouraging.

  8. Are all maximally entangled states pure?

    NASA Astrophysics Data System (ADS)

    Cavalcanti, D.; Brandão, F. G. S. L.; Terra Cunha, M. O.

    2005-10-01

    We study if all maximally entangled states are pure through several entanglement monotones. In the bipartite case, we find that the same conditions which lead to the uniqueness of the entropy of entanglement as a measure of entanglement exclude the existence of maximally mixed entangled states. In the multipartite scenario, our conclusions allow us to generalize the idea of the monogamy of entanglement: we establish the polygamy of entanglement, expressing that if a general state is maximally entangled with respect to some kind of multipartite entanglement, then it is necessarily factorized of any other system.

  9. Electrostatic Precipitation in Nearly Pure Gaseous Nitrogen

    NASA Technical Reports Server (NTRS)

    Buhler, Charles; Calle, Carlos; Clements, Sid; Cox, Bobby; Ritz, Mindy

    2008-01-01

    Electrostatic precipitation was performed in a nearly pure gaseous nitrogen system as a possible remedy for black dust contaminant from high pressure 6000 psi lines at the NASA Kennedy Space Center. The results of a prototype electrostatic precipitator that was built and tested using nitrogen gas at standard atmospheric pressures is presented. High voltage pulsed waveforms are generated using a rotating spark gap system at 30 Hz. A unique dust delivery system utilizing the Venturi effect was devised that supplies a given amount of dust per unit time for testing purposes.

  10. Preparation of a pure molecular quantum gas.

    PubMed

    Herbig, Jens; Kraemer, Tobias; Mark, Michael; Weber, Tino; Chin, Cheng; Nägerl, Hanns-Christoph; Grimm, Rudolf

    2003-09-12

    An ultracold molecular quantum gas is created by application of a magnetic field sweep across a Feshbach resonance to a Bose-Einstein condensate of cesium atoms. The ability to separate the molecules from the atoms permits direct imaging of the pure molecular sample. Magnetic levitation enables study of the dynamics of the ensemble on extended time scales. We measured ultralow expansion energies in the range of a few nanokelvin for a sample of 3000 molecules. Our observations are consistent with the presence of a macroscopic molecular matter wave. PMID:12934014

  11. Synthesis of highly phase pure BSCCO superconductors

    DOEpatents

    Dorris, S.E.; Poeppel, R.B.; Prorok, B.C.; Lanagan, M.T.; Maroni, V.A.

    1995-11-21

    An article and method of manufacture (Bi, Pb)-Sr-Ca-Cu-O superconductor are disclosed. The superconductor is manufactured by preparing a first powdered mixture of bismuth oxide, lead oxide, strontium carbonate, calcium carbonate and copper oxide. A second powdered mixture is then prepared of strontium carbonate, calcium carbonate and copper oxide. The mixtures are calcined separately with the two mixtures then combined. The resulting combined mixture is then subjected to a powder in tube deformation and thermal processing to produce a substantially phase pure (Bi, Pb)-Sr-Ca-Cu-O superconductor. 5 figs.

  12. Synthesis of highly phase pure BSCCO superconductors

    DOEpatents

    Dorris, Stephen E.; Poeppel, Roger B.; Prorok, Barton C.; Lanagan, Michael T.; Maroni, Victor A.

    1995-01-01

    An article and method of manufacture of (Bi, Pb)-Sr-Ca-Cu-O superconductor. The superconductor is manufactured by preparing a first powdered mixture of bismuth oxide, lead oxide, strontium carbonate, calcium carbonate and copper oxide. A second powdered mixture is then prepared of strontium carbonate, calcium carbonate and copper oxide. The mixtures are calcined separately with the two mixtures then combined. The resulting combined mixture is then subjected to a powder in tube deformation and thermal processing to produce a substantially phase pure (Bi, Pb)-Sr-Ca-Cu-O superconductor.

  13. Optical pure spin current injection in graphene

    NASA Astrophysics Data System (ADS)

    Rioux, Julien; Burkard, Guido

    2013-03-01

    Pure spin current injection by optical methods is investigated in single-layer and bilayer graphene within the tight-binding model, including bias and interlayer coupling effects. Interlayer coupling in bilayer graphene has a distinct qualitative effect on the polarization dependence of the spin current injection. In combination with interlayer coupling, which induces trigonal warping of the electronic bands, the bias voltage allows to control the warping at the Fermi surface. The resulting implications for the spin current injection are presented. Unlike the previously presented charge current injection [J. Rioux et al., PRB 83, 195406 (2011)], the effect presented here relies on a single monochromatic beam.

  14. Femtosecond pulses propagation through pure water

    NASA Astrophysics Data System (ADS)

    Naveira, Lucas; Sokolov, Alexei; Byeon, Joong-Hyeok; Kattawar, George

    2007-10-01

    Recently, considerable attention has been dedicated to the field of optical precursors, which can possibly be applied to long-distance underwater communications. Input beam intensities have been carefully adjusted to keep experiments in the linear regime, and some experiments have shown violation of the Beer-Lambert law. We are presently carrying out experiments using femtosecond laser pulses propagating through pure water strictly in the linear regime to study this interesting and important behavior. We are also employing several new and innovative schemes to more clearly define the phenomena.

  15. Purely cubic action for string field theory

    NASA Technical Reports Server (NTRS)

    Horowitz, G. T.; Lykken, J.; Rohm, R.; Strominger, A.

    1986-01-01

    It is shown that Witten's (1986) open-bosonic-string field-theory action and a closed-string analog can be written as a purely cubic interaction term. The conventional form of the action arises by expansion around particular solutions of the classical equations of motion. The explicit background dependence of the conventional action via the Becchi-Rouet-Stora-Tyutin operator is eliminated in the cubic formulation. A closed-form expression is found for the full nonlinear gauge-transformation law.

  16. Towards chirality-pure carbon nanotubes

    NASA Astrophysics Data System (ADS)

    Zhang, Yani; Zheng, Lianxi

    2010-10-01

    Current as-grown single-walled carbon nanotubes vary in diameter and chirality, which results in variations in their electronic and optical properties. Two approaches have been intensively studied to obtain chirality-pure nanotube structures and thus uniform properties for advanced applications. The first approach involves the post-synthesis separation according to the nanotubes' chiral vectors (n, m), and the second one involves direct synthes of carbon nanotubes with the same (n, m). This paper reviews the efforts along these two directions, with emphasis on the most recent progress of post-synthesis separation and the perspectives of controllable synthesis.

  17. Are all maximally entangled states pure?

    SciTech Connect

    Cavalcanti, D.; Brandao, F.G.S.L.; Terra Cunha, M.O.

    2005-10-15

    We study if all maximally entangled states are pure through several entanglement monotones. In the bipartite case, we find that the same conditions which lead to the uniqueness of the entropy of entanglement as a measure of entanglement exclude the existence of maximally mixed entangled states. In the multipartite scenario, our conclusions allow us to generalize the idea of the monogamy of entanglement: we establish the polygamy of entanglement, expressing that if a general state is maximally entangled with respect to some kind of multipartite entanglement, then it is necessarily factorized of any other system.

  18. Cold-Sprayed Nanostructured Pure Cobalt Coatings

    NASA Astrophysics Data System (ADS)

    Cavaliere, P.; Perrone, A.; Silvello, A.

    2016-08-01

    Cold-sprayed pure cobalt coatings were deposited on carbon-steel substrate. Submicrometer particles for spraying were produced via cryomilling. Deposits were produced using different processing conditions (gas temperature and pressure, nozzle-to-substrate distance) to evaluate the resulting variations in grain size dimension, microhardness, adhesion strength, and porosity. The coating mechanical properties improved greatly with higher temperature and carrying-gas pressure. The coating microstructure was analyzed as a function of spraying condition by transmission electron microscopy (TEM) observations, revealing many different microstructural features for coatings experiencing low or high strain rates during deposition.

  19. Pure seminoma: A review and update

    PubMed Central

    2011-01-01

    Pure seminoma is a rare pathology of the young adult, often discovered in the early stages. Its prognosis is generally excellent and many therapeutic options are available, especially in stage I tumors. High cure rates can be achieved in several ways: standard treatment with radiotherapy is challenged by surveillance and chemotherapy. Toxicity issues and the patients' preferences should be considered when management decisions are made. This paper describes firstly the management of primary seminoma and its nodal involvement and, secondly, the various therapeutic options according to stage. PMID:21819630

  20. Pure phase decoherence in a ring geometry

    SciTech Connect

    Zhu, Z.; Aharony, A.; Entin-Wohlman, O.; Stamp, P. C. E.

    2010-06-15

    We study the dynamics of pure phase decoherence for a particle hopping around an N-site ring, coupled both to a spin bath and to an Aharonov-Bohm flux which threads the ring. Analytic results are found for the dynamics of the influence functional and of the reduced density matrix of the particle, both for initial single wave-packet states, and for states split initially into two separate wave packets moving at different velocities. We also give results for the dynamics of the current as a function of time.

  1. A gravity loading countermeasure skinsuit

    NASA Astrophysics Data System (ADS)

    Waldie, James M.; Newman, Dava J.

    2011-04-01

    Despite the use of several countermeasures, significant physiological deconditioning still occurs during long duration spaceflight. Bone loss - primarily due to the absence of loading in microgravity - is perhaps the greatest challenge to resolve. This paper describes a conceptual Gravity Loading Countermeasure Skinsuit (GLCS) that induces loading on the body to mimic standing and - when integrated with other countermeasures - exercising on Earth. Comfort, mobility and other operational issues were explored during a pilot study carried out in parabolic flight for prototype suits worn by three subjects. Compared to the 1- or 2-stage Russian Pingvin Suits, the elastic mesh of the GLCS can create a loading regime that gradually increases in hundreds of stages from the shoulders to the feet, thereby reproducing the weight-bearing regime normally imparted by gravity with much higher resolution. Modelling shows that the skinsuit requires less than 10 mmHg (1.3 kPa) of compression for three subjects of varied gender, height and mass. Negligible mobility restriction and excellent comfort properties were found during the parabolic flights, which suggests that crewmembers should be able to work normally, exercise or sleep while wearing the suit. The suit may also serve as a practical 1 g harness for exercise countermeasures and vibration applications to improve dynamic loading.

  2. Hippocampal volume and shape in pure subcortical vascular dementia.

    PubMed

    Kim, Geon Ha; Lee, Jae Hong; Seo, Sang Won; Kim, Jeong Hun; Seong, Joon-Kyung; Ye, Byoung Seok; Cho, Hanna; Noh, Young; Kim, Hee Jin; Yoon, Cindy W; Oh, Seung Jun; Kim, Jae Seung; Choe, Yearn Seong; Lee, Kyung Han; Kim, Sung Tae; Hwang, Jung Won; Jeong, Jee Hyang; Na, Duk L

    2015-01-01

    The purposes of the present study were to explore whether hippocampal atrophy exists in pure subcortical vascular dementia (SVaD) as defined by negative (11)C-Pittsburg compound-B (PiB(-)) positron emission tomography and to compare hippocampal volume and shape between PiB(-) SVaD and PiB positive (PiB(+)) Alzheimer's disease (AD) dementia. Hippocampal volume and shape were compared among 40 patients with PiB(-) SVaD, 34 with PiB(+) AD, and 21 elderly with normal cognitive function (NC). The normalized hippocampal volume of PiB(-) SVaD was significantly smaller than NC but larger than that of PiB(+) AD (NC > PiB(-) SVaD > PiB(+) AD). Both PiB(-) SVaD and PiB(+) AD patients had deflated shape changes in the cornus ammonis (CA) 1 and subiculum compared with NC. However, direct comparison between PiB(-) SVaD and PiB(+) AD demonstrated more inward deformity in the subiculum of the left hippocampus in PiB(+) AD. PiB(-) SVaD patients did have smaller hippocampal volumes and inward shape change on CA 1 and subiculum compared with NC, suggesting that cumulative ischemia without amyloid pathology could lead to hippocampal atrophy and shape changes. PMID:25444608

  3. Nanoporous Au: an unsupported pure gold catalyst?

    SciTech Connect

    Wittstock, A; Neumann, B; Schaefer, A; Dumbuya, K; Kuebel, C; Biener, M; Zielasek, V; Steinrueck, H; Gottfried, M; Biener, J; Hamza, A; B?umer, M

    2008-09-04

    The unique properties of gold especially in low temperature CO oxidation have been ascribed to a combination of various effects. In particular, particle sizes below a few nm and specific particle-support interactions have been shown to play important roles. On the contrary, recent reports revealed that monolithic nanoporous gold (npAu) prepared by leaching a less noble metal, such as Ag, out of the corresponding alloy can also exhibit remarkably high catalytic activity for CO oxidation, even though no support is present. Therefore, it was claimed to be a pure and unsupported gold catalyst. We investigated npAu with respect to its morphology, surface composition and catalytic properties. In particular, we studied the reaction kinetics for low temperature CO oxidation in detail taking mass transport limitation due to the porous structure of the material into account. Our results reveal that Ag, even if removed almost completely from the bulk, segregates to the surface resulting in surface concentrations of up to 10 at%. Our data suggest that this Ag plays a significant role in activation of molecular oxygen. Therefore, npAu should be considered as a bimetallic catalyst rather than a pure Au catalyst.

  4. LHC Signals of Pure Gravity Mediation

    NASA Astrophysics Data System (ADS)

    Feldstein, Brian

    2013-05-01

    Evidence is mounting that natural supersymmetry at the weak scale is not realized in nature. This evidence comes from collider searches, a lack of new flavor changing neutral current effects, and now also the size of the measured Higgs mass. On the other hand, string theory suggests that supersymmetry might be present at some energy scale, and gauge coupling unification and dark matter imply that that energy scale may be relatively low. The simplest model to address all of these hints is arguably "pure gravity mediation", in which the scalar superpartner masses are taken to be perhaps 100 TeV, with gauginos automatically acquiring loop factor suppressed masses of order TeV. The gauginos might then be the only superpartners accessible to the LHC. Unification and LSP dark matter are maintained (with a wino LSP) at the cost of a 10-5 or 10-6 fine tuning. Here I will discuss the structure and LHC phenomenology of pure gravity mediation.

  5. Light Higgsinos in pure gravity mediation

    NASA Astrophysics Data System (ADS)

    Evans, Jason L.; Ibe, Masahiro; Olive, Keith A.; Yanagida, Tsutomu T.

    2015-03-01

    Pure gravity mediation, with two free parameters, is a minimalistic approach to supergravity models, yet it is capable of incorporating radiative electroweak symmetry breaking, a Higgs mass in agreement with the experimental measurement, without violating any phenomenological constraints. The model may also contain a viable dark matter candidate in the form of a wino. Here, we extend the minimal model by allowing the μ term to be a free parameter equivalent to allowing the two Higgs soft masses, m1 and m2, to differ from other scalar masses, which are set by the gravitino mass. In particular, we examine the region of parameter space where μ ≪m3 /2, in which case the Higgsino becomes the lightest supersymmetric particle and a dark matter candidate. We also consider a generalization of pure gravity mediation that incorporates a Peccei-Quinn symmetry which determines the μ term dynamically. In this case we show that the dark matter may either be in the form of an axion and/or a neutralino and that the lightest supersymmetric particle may be either a wino, bino, or Higgsino.

  6. Cosmic Shear - with ACS Pure Parallel Observations

    NASA Astrophysics Data System (ADS)

    Ratnatunga, Kavan

    2002-07-01

    The ACS, with greater sensitivity and sky coverage, will extend our ability to measure the weak gravitational lensing of galaxy images caused by the large scale distribution of dark matter. We propose to use the ACS in pure parallel {non- proprietary} mode, following the guidelines of the ACS Default Pure Parallel Program. Using the HST Medium Deep Survey WFPC2 database we have measured cosmic shear at arc-min angular scales. The MDS image parameters, in particular the galaxy orientations and axis ratios, are such that any residual corrections due to errors in the PSF or jitter are much smaller than the measured signal. This situation is in stark contrast with ground-based observations. We have also developed a statistical analysis procedure to derive unbiased estimates of cosmic shear from a large number of fields, each of which has a very small number of galaxies. We have therefore set the stage for measurements with the ACS at fainter apparent magnitudes and smaller, 10 arc-second scales corresponding to larger cosmological distances. We will adapt existing MDS WFPC2 maximum likelihood galaxy image analysis algorithms to work with the ACS. The analysis would also yield an online database similar to that in archive.stsci.edu/mds/

  7. Time Evolution of Pure Gravitational Waves

    NASA Astrophysics Data System (ADS)

    Miyama, S. M.

    1981-03-01

    Numerical solutions to the Einstein equations in the case of pure gravitational waves are given. The system is assumed to be axially symmetric and non-rotating. The time symmetric initial data and the conformally flat initial data are obtained by solving the constraint equations at t=0. The time evolution of these initial data depends strongly on the initial amplitude of the gravitational waves. In the case of the low initial amplitude, waves only disperse to null infinity. By comparing the initial gravitational energy with the total energy loss through an r=constant surface, it is concluded that the Newman-Penrose method and the Gibbon-Hawking method are the most desirable for measuring the energy flux of gravitational radiation numerically. In the case that the initial ratio of the spatial extent of the gravitational waves to the Schwarzschild radius (M/2) is smaller than about 300, the waves collapse by themselves, leading to formation of a black hole. The analytic solutions of the linearized Einstein equations for the pure gravitational waves are also shown.

  8. Impedance matching between ventricle and load.

    PubMed

    Piene, H

    1984-01-01

    Impedance matching in the cardiovascular system is discussed in light of two models of ventricle and load: a Thevenin equivalent consisting of a hydromotive pressure source and an internal, source resistance and compliance in parallel; and a time-varying compliance filled from a constant pressure source and ejecting into a load of three components, a central resistor, a compliance, and a peripheral resistance. According to the Thevenin analog, the energy source and the load are matched when the load resistance is T/t times the internal source resistance (T is total cycle length, t is systolic time interval). Both from this model and from the variable compliance model it appears that optimum matching between source and load depends on the compliance of the Windkessel, as low compliance shifts the matching load resistance to a low value. Animal experiments (isolated cat hearts) indicated that both left and right ventricles at normal loads work close to their maxima of output hydraulic power, and, according to experiments in the right ventricle, maximum power output is related to load resistance and compliance as predicted by the above models. From an experimentally determined relationship among instantaneous ventricular pressure and volume (right ventricle of isolated cat hearts), an optimum load impedance was calculated on the basis of the assumption that the ratio between stroke work and static, potential energy developed in the ventricular cavity is maximum. The optimum load impedance found by this procedure closely resembles the normal input impedance of the cat lung vessel bed. PMID:6507966

  9. Biaxial fatigue loading of notched composites

    NASA Technical Reports Server (NTRS)

    Francis, P. H.; Walrath, D. E.; Sims, D. F.; Weed, D. N.

    1977-01-01

    Thin walled, 2.54-cm (1-in.) diameter tubular specimens of T300/934 graphite/epoxy were fabricated and fatigue cycled in combinations of axial, torsional, and internal pressure loading. Two different four-ply layup configurations were tested: (0/90)S and (+ or - 45)S; all tubes contained a 0.48-cm (3/16-in.) diameter circular hole penetrating one wall midway along the tube length. S-N curves were developed to characterize fatigue behavior under pure axial, torsional, or internal pressure loading, as well as combined loading fatigue. A theory was developed based on the Hill plane stress model which enabled the S-N curve for combined stress states to be predicted from the S-N data for the uniaxial loading modes. Correlation of the theory with the experimental data proved to be remarkably good.

  10. Biaxial fatigue loading of notched composites

    NASA Technical Reports Server (NTRS)

    Francis, P. H.; Walrath, D. E.; Sims, D. F.; Weed, D. N.

    1977-01-01

    Thin-walled, 2.54-cm diameter tubular specimens of graphite/epoxy were fatigue cycled in combinations of axial, torsional, and internal pressure loading. Two different four-ply layup configurations were tested: (0-90)s and (+ or- 45)s; each tube contained a 0.48-cm diameter circular hole penetrating one wall midway along the tube length. S-N curves were developed to characterize fatigue behavior under pure axial, torsional, or internal pressure loading, as well as combined loading fatigue. A theory was developed based on a plane stress model which enabled the S-N curve for combined stress states to be predicted from the S-N data for the uniaxial loading modes. Correlation of the theory with the experimental data proved to be remarkably good.

  11. Anomalous rectification in a purely electronic memristor

    NASA Astrophysics Data System (ADS)

    Wang, Jingrui; Pan, Ruobing; Cao, Hongtao; Wang, Yang; Liang, Lingyan; Zhang, Hongliang; Gao, Junhua; Zhuge, Fei

    2016-10-01

    An anomalous rectification was observed in a purely electronic memristive device Ti/ZnO/Pt. It could be due to (1) an Ohmic or quasi-Ohmic contact at the ZnO/Pt interface and (2) a Schottky contact at the Ti/ZnO interface. The Ohmic contact originates from the reduction of ZnO occurring in the whole film instead of only at the Ti/ZnO interface. The Schottky contact may come from moisture adsorbed in the nanoporous ZnO. The conduction in the electroformed device is controlled by the carrier trapping/detrapping of the trap sites, inducing a poor rectification and high nonlinearity. Furthermore, a complementary resistive switching was achieved.

  12. Bipedal nanowalker by pure physical mechanisms.

    PubMed

    Cheng, Juan; Sreelatha, Sarangapani; Hou, Ruizheng; Efremov, Artem; Liu, Ruchuan; van der Maarel, Johan R C; Wang, Zhisong

    2012-12-01

    Artificial nanowalkers are inspired by biomolecular counterparts from living cells, but remain far from comparable to the latter in design principles. The walkers reported to date mostly rely on chemical mechanisms to gain a direction; they all produce chemical wastes. Here we report a light-powered DNA bipedal walker based on a design principle derived from cellular walkers. The walker has two identical feet and the track has equal binding sites; yet the walker gains a direction by pure physical mechanisms that autonomously amplify an intrasite asymmetry into a ratchet effect. The nanowalker is free of any chemical waste. It has a distinct thermodynamic feature that it possesses the same equilibrium before and after operation, but generates a truly nonequilibrium distribution during operation. The demonstrated design principle exploits mechanical effects and is adaptable for use in other nanomachines.

  13. Pure White Cell Aplasia and Necrotizing Myositis

    PubMed Central

    Kim, Peter Geon; Suh, Joome; Adelman, Max W.; Oduro, Kwadwo; Williams, Erik; Brunner, Andrew M.; Kuter, David J.

    2016-01-01

    Pure white cell aplasia (PWCA) is a rare hematologic disorder characterized by the absence of neutrophil lineages in the bone marrow with intact megakaryopoiesis and erythropoiesis. PWCA has been associated with autoimmune, drug-induced, and viral exposures. Here, we report a case of a 74-year-old female who presented with severe proximal weakness without pain and was found to have PWCA with nonspecific inflammatory necrotizing myositis and acute liver injury on biopsies. These findings were associated with a recent course of azithromycin and her daily use of a statin. Myositis improved on prednisone but PWCA persisted. With intravenous immunoglobulin and granulocyte-colony stimulating factor therapies, her symptoms and neutrophil counts improved and were sustained for months. PMID:27073704

  14. Fock expansion of multimode pure Gaussian states

    SciTech Connect

    Cariolaro, Gianfranco; Pierobon, Gianfranco

    2015-12-15

    The Fock expansion of multimode pure Gaussian states is derived starting from their representation as displaced and squeezed multimode vacuum states. The approach is new and appears to be simpler and more general than previous ones starting from the phase-space representation given by the characteristic or Wigner function. Fock expansion is performed in terms of easily evaluable two-variable Hermite–Kampé de Fériet polynomials. A relatively simple and compact expression for the joint statistical distribution of the photon numbers in the different modes is obtained. In particular, this result enables one to give a simple characterization of separable and entangled states, as shown for two-mode and three-mode Gaussian states.

  15. Pure Varus Injury to the Knee Joint.

    PubMed

    Yoo, Jae Ho; Lee, Jung Ha; Chang, Chong Bum

    2015-06-01

    A 30-year-old male was involved in a car accident. Radiographs revealed a depressed marginal fracture of the medial tibial plateau and an avulsion fracture of the fibular head. Magnetic resonance imaging showed avulsion fracture of Gerdy's tubercle, injury to the posterior cruciate ligament (PCL), posterior horn of the medial meniscus, and the attachments of the lateral collateral ligament and the biceps femoris tendon. The depressed fracture of the medial tibial plateau was elevated and stabilized using a cannulated screw and washer. The injured lateral and posterolateral corner (PLC) structures were repaired and augmented by PLC reconstruction. However, the avulsion fracture of Gerdy's tubercle was not fixed because it was minimally displaced and the torn PCL was also not repaired or reconstructed. We present a unique case of pure varus injury to the knee joint. This case contributes to our understanding of the mechanism of knee injury and provides insight regarding appropriate treatment plans for this type of injury. PMID:26217477

  16. Adsorption of hydroxyacetone on pure ice surfaces.

    PubMed

    Petitjean, Mélanie; Darvas, Maria; Picaud, Sylvain; Jedlovszky, Pál; Le Calvé, Stéphane

    2010-12-17

    The adsorption of hydroxyacetone molecules at the surface of ice is investigated by means of flow-tube reactor measurements in the temperature range: 213-253 K. The number of molecules adsorbed per surface unit is conventionally plotted as a function of the absolute gas concentration of hydroxyacetone and is compared to that previously obtained for acetone and ethanol. The enthalpy of adsorption and the monolayer capacity at the ice surface are determined. In addition, molecular dynamics simulations are performed to support the experimental results. However, it is shown that the available interaction potential between hydroxyacetone and ice is not accurate enough to allow a robust detailed analysis of the adsorption process. Finally, a rapid estimation of the hydroxyacetone partitioning between the gas phase and ice shows that in the densest ice clouds, up to 29% of hydroxyacetone could be adsorbed on pure ice surfaces at 203 K.

  17. Synaptic devices based on purely electronic memristors

    NASA Astrophysics Data System (ADS)

    Pan, Ruobing; Li, Jun; Zhuge, Fei; Zhu, Liqiang; Liang, Lingyan; Zhang, Hongliang; Gao, Junhua; Cao, Hongtao; Fu, Bing; Li, Kang

    2016-01-01

    Memristive devices have been widely employed to emulate biological synaptic behavior. In these cases, the memristive switching generally originates from electrical field induced ion migration or Joule heating induced phase change. In this letter, the Ti/ZnO/Pt structure was found to show memristive switching ascribed to a carrier trapping/detrapping of the trap sites (e.g., oxygen vacancies or zinc interstitials) in ZnO. The carrier trapping/detrapping level can be controllably adjusted by regulating the current compliance level or voltage amplitude. Multi-level conductance states can, therefore, be realized in such memristive device. The spike-timing-dependent plasticity, an important Hebbian learning rule, has been implemented in this type of synaptic device. Compared with filamentary-type memristive devices, purely electronic memristors have potential to reduce their energy consumption and work more stably and reliably, since no structural distortion occurs.

  18. Preparation and accurate measurement of pure ozone.

    PubMed

    Janssen, Christof; Simone, Daniela; Guinet, Mickaël

    2011-03-01

    Preparation of high purity ozone as well as precise and accurate measurement of its pressure are metrological requirements that are difficult to meet due to ozone decomposition occurring in pressure sensors. The most stable and precise transducer heads are heated and, therefore, prone to accelerated ozone decomposition, limiting measurement accuracy and compromising purity. Here, we describe a vacuum system and a method for ozone production, suitable to accurately determine the pressure of pure ozone by avoiding the problem of decomposition. We use an inert gas in a particularly designed buffer volume and can thus achieve high measurement accuracy and negligible degradation of ozone with purities of 99.8% or better. The high degree of purity is ensured by comprehensive compositional analyses of ozone samples. The method may also be applied to other reactive gases. PMID:21456766

  19. Pure Rotational Spectroscopy of Vinyl Mercaptan

    NASA Astrophysics Data System (ADS)

    Martin-Drumel, Marie-Aline; Zingsheim, Oliver; Thorwirth, Sven; Müller, Holger S. P.; Lewen, Frank; Schlemmer, Stephan

    2014-06-01

    Vinyl mercaptan (ethenethiol, CH_2=CHSH) exists in the gas phase in two distinct rotameric forms, syn (planar) and anti (quasi-planar in the ground vibrational state). The microwave spectra of these two isomers were investigated previously, however not exceeding frequencies of about 65 GHz. In the present investigation, the pure rotational spectra of both species have been investigated at millimeter wavelengths. Vinyl mercaptan was produced in a radiofrequency discharge through a constant flow of ethanedithiol at low pressure. Both syn and anti rotamers were observed and new extensive sets of molecular parameters were obtained. Owing to its close structural relationship to vinyl alcohol and the astronomical abundance of complex sulfur-bearing molecules, vinyl mercaptan is a plausible candidate for future radio astronomical searches. M. Tanimoto et al. J. Mol. Spectrosc. 78, 95--105 & 106--119 (1979)

  20. 7 CFR 201.64 - Pure live seed.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Pure live seed. 201.64 Section 201.64 Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Tolerances § 201.64 Pure live seed. The tolerance for pure live seed shall be determined...

  1. 7 CFR 201.64 - Pure live seed.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Pure live seed. 201.64 Section 201.64 Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Tolerances § 201.64 Pure live seed. The tolerance for pure live seed shall be determined...

  2. 7 CFR 201.64 - Pure live seed.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Pure live seed. 201.64 Section 201.64 Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Tolerances § 201.64 Pure live seed. The tolerance for pure live seed shall be determined...

  3. 7 CFR 201.64 - Pure live seed.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Pure live seed. 201.64 Section 201.64 Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Tolerances § 201.64 Pure live seed. The tolerance for pure live seed shall be determined...

  4. 7 CFR 201.64 - Pure live seed.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Pure live seed. 201.64 Section 201.64 Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Tolerances § 201.64 Pure live seed. The tolerance for pure live seed shall be determined...

  5. ThermoData Engine Database - Pure Compounds and Binary Mixtures

    National Institute of Standards and Technology Data Gateway

    SRD 103b NIST ThermoData Engine Version 6.0 - Pure CompoThermoData Engine Database - Pure Compounds and Binary Mixtures (PC database for purchase)   This database contains property data for more than 21,000 pure compounds, 37,500 binary mixtures, 10,000 ternary mixtures, and 6,000 chemical reactions.

  6. Social cognition in "pure" delusional disorder.

    PubMed

    Bömmer, Isabel; Brüne, Martin

    2006-09-01

    Introduction. Delusional disorders are characterised by monothematic, "encapsulated" and incorrigible false beliefs and misinterpretations of social signals. Due to the rarity of cases with "pure" delusional disorder (DD) in clinical settings most studies of social cognition in delusional patients have focused on patients with paranoid schizophrenia. In the present study we sought to examine emotion recognition, theory of mind abilities, and pragmatic language comprehension in patients with delusional disorder. Methods. Social cognition was assessed in 21 patients recruited over a 3-year period who were diagnosed with delusional disorder, paranoid, erotomanic, or jealous type. In addition to an emotion recognition and theory of mind test battery, we included a novel German Proverb Test, which has been found indicative of subtle theory of mind deficits in schizophrenic patients. Executive functioning was assessed using the Wisconsin Card Sorting Test (WCST). Psychopathology was measured using the Positive and Negative Symptoms Scale (PANSS). Patients' task performance was compared to a group of 22 healthy control persons paralleled for verbal intelligence, education, and age. Results. Patients with DD made significantly more perseverative errors in the WCST, they performed more poorly on the theory of mind tasks and the proverb test, but were unimpaired in basic emotion recognition abilities relative to controls. When executive functioning was co-varied out, the group differences in theory of mind disappeared, whereas the greater propensity of patients with DD to interpret proverbs literally remained significant. Conclusions. In "pure" DD the basic social cognitive abilities appear to be preserved. Difficulties in metaphorical speech comprehension and executive functioning could, however, indicate more subtle social cognitive deficits in these patients. PMID:17354084

  7. Temperature dependent deformation mechanisms in pure amorphous silicon

    SciTech Connect

    Kiran, M. S. R. N. Haberl, B.; Williams, J. S.; Bradby, J. E.

    2014-03-21

    High temperature nanoindentation has been performed on pure ion-implanted amorphous silicon (unrelaxed a-Si) and structurally relaxed a-Si to investigate the temperature dependence of mechanical deformation, including pressure-induced phase transformations. Along with the indentation load-depth curves, ex situ measurements such as Raman micro-spectroscopy and cross-sectional transmission electron microscopy analysis on the residual indents reveal the mode of deformation under the indenter. While unrelaxed a-Si deforms entirely via plastic flow up to 200 °C, a clear transition in the mode of deformation is observed in relaxed a-Si with increasing temperature. Up to 100 °C, pressure-induced phase transformation and the observation of either crystalline (r8/bc8) end phases or pressure-induced a-Si occurs in relaxed a-Si. However, with further increase of temperature, plastic flow rather than phase transformation is the dominant mode of deformation. It is believed that the elevated temperature and pressure together induce bond softening and “defect” formation in structurally relaxed a-Si, leading to the inhibition of phase transformation due to pressure-releasing plastic flow under the indenter.

  8. Equation of state, initiation, and detonation of pure ammonium nitrate

    NASA Astrophysics Data System (ADS)

    Robbins, D. L.; Sheffield, S. A.; Dattelbaum, D. M.; Velisavljevic, N.; Stahl, D. B.

    2009-06-01

    Ammonium nitrate (AN) is a widely used fertilizer and mining explosive throughout the world. One of the more common explosives using AN is called ANFO, a mixture of AN prills and fuel oil in a 94:6 ratio by weight. The AN prills are specially made to absorb the fuel oil, forming a mixture that reacts under shock loading through a diffusion-controlled process, resulting in a non-ideal explosive with detonation velocities around 4 km/s. While there are a number of studies on ANFO, there are only a few studies relating to the equation of state (EOS) and detonation properties of pure AN - resulting mainly from studies of accidents that have occurred during transportation of large quantities of AN. We present the results of a series of gas gun-driven plate impact experiments on pressed AN ranging in density from 1.72 to 0.9 g/cm^3. Several of the high density experiments were performed in front surface impact geometry, in which pressed AN disks were built into the projectile front and impacted onto LiF windows. Additional experiments at low density have been done in ``half cell'' multiple magnetic gauge gun experiments. From this work a complete unreacted EOS has been developed, as well as some initiation and detonation information. Additional high pressure x-ray diffraction experiments in diamond anvil cells have provided a static isotherm for AN.

  9. Effects of grain size on the spallation behavior of pure copper under plate-impact loading

    NASA Astrophysics Data System (ADS)

    Jiang, ZhaoXiu; Peng, Hui; Xing, MingZhi; Shen, HaiTing; He, HongLiang; Wang, YongGang

    2015-09-01

    The effects of grain size on the dynamic tensile fracture (or spall) response were investigated for high purity copper materials by plate-impact experiments. The spall strength estimated from the free surface velocity profile is nearly constant with no significant effect from the grain size. However, differences are observed in the acceleration rate of velocity rebound beyond the minima. This may be attributed to the effect of grain size on the growth rate of damage. Metallographic analyses of the fracture surface show that the characteristic feature of the fracture surface clearly depends on the grain size. In the smaller samples, the fracture surfaces are decorated with large, high-density ductile dimples suggesting that the preferential failure mode is ductile intergranular fracture. In the larger samples, the fracture surfaces have a rock candy appearance with small, brittle, high density dimples as well as large ductile dimples suggesting that the fracture mode is a mix of both brittle intergranular fracture and ductile transgranular fracture.

  10. Updated analytical solutions of continuity equation for electron beams precipitation - I. Pure collisional and pure ohmic energy losses

    NASA Astrophysics Data System (ADS)

    Dobranskis, R. R.; Zharkova, V. V.

    2015-10-01

    We present updated analytical solutions of continuity equations for power-law beam electrons precipitating in (a) purely collisional losses and (b) purely ohmic losses. The solutions of continuity equation (CE) normalized on electron density presented in Dobranskis & Zharkova are found by method of characteristics eliminating a mistake in the density characteristic pointed out by Emslie et al. The corrected electron beam differential densities (DD) for collisions are shown to have energy spectra with the index of -(γ + 1)/2, coinciding with the one derived from the inverse problem solution by Brown, while being lower by 1/2 than the index of -γ/2 obtained from CE for electron flux. This leads to a decrease of the index of mean electron spectra from -(γ - 2.5) (CE for flux) to -(γ - 2.0) (CE for electron density). The similar method is applied to CE for electrons precipitating in electric field induced by the beam itself. For the first time, the electron energy spectra are calculated for both constant and variable electric fields by using CE for electron density. We derive electron DD for precipitating electrons (moving towards the photosphere, μ = +1) and `returning' electrons (moving towards the corona, μ = -1). The indices of DD energy spectra are reduced from -γ - 1 (CE for flux) to -γ (CE for electron density). While the index of mean electron spectra is increased by 0.5, from -γ + 0.5 (CE for flux) to -γ + 1(CE for electron density). Hard X-ray intensities are also calculated for relativistic cross-section for the updated differential spectra revealing closer resemblance to numerical Fokker-Planck (FP) solutions.

  11. From word superiority to word inferiority: visual processing of letters and words in pure alexia.

    PubMed

    Habekost, Thomas; Petersen, Anders; Behrmann, Marlene; Starrfelt, Randi

    2014-01-01

    Visual processing and naming of individual letters and short words were investigated in four patients with pure alexia. To test processing at different levels, the same stimuli were studied across a naming task and a visual perception task. The normal word superiority effect was eliminated in both tasks for all patients, and this pattern was more pronounced in the more severely affected patients. The relationship between performance with single letters and words was, however, not straightforward: One patient performed within the normal range on the letter perception task, while being severely impaired in letter naming and word processing, and performance with letters and words was dissociated in all four patients, with word reading being more severely impaired than letter recognition. This suggests that the word reading deficit in pure alexia may not be reduced to an impairment in single letter perception. PMID:24801564

  12. Improving Power-Supply Regulation for Pulsed Loads

    NASA Technical Reports Server (NTRS)

    Gulick, C. R.; Chan, R. B.

    1982-01-01

    Power supply voltage-regulator circuit speeds up response to sudden load changes. As load increases, additional feedback path is enabled. Path bypasses and provides faster loop response than normal feedback path. Steady-state instability due to faster loop response avoided by progressively disabling bypass loop and allowing normal feedback path to take over.

  13. Heterosis in normal versus dwarf laying hens.

    PubMed

    Merat, P; Minvielle, F; Bordas, A; Coquerelle, G

    1994-01-01

    The effect of genotype at the sex-linked dwarf locus on heterosis in crosses between a White Leghorn and a brown egg line for body weight, egg production, and related traits was studied. Heterozygous Dw/dw males were used to produce normal and dwarf pullets in each of the pure lines and their reciprocal crosses (eight genotype-line combinations). There were 54 pullets per combination. Line differences were significant for shank length, body weights at 8, 17, and 52 wk, age at first egg, egg number, clutch length, rate of lay, and egg weight. Heterosis was observed for all of these traits. Body weight as a covariate was not important in analyses of egg number, clutch length, and egg weight. The egg production reduction associated with the dw gene in pure lines was smaller in F1 hens. This discovery may be adequate to warrant use of dwarf crossbred hens for egg production.

  14. Simulation of flight maneuver-load distributions by utilizing stationary, non-Gaussian random load histories

    NASA Technical Reports Server (NTRS)

    Leybold, H. A.

    1971-01-01

    Random numbers were generated with the aid of a digital computer and transformed such that the probability density function of a discrete random load history composed of these random numbers had one of the following non-Gaussian distributions: Poisson, binomial, log-normal, Weibull, and exponential. The resulting random load histories were analyzed to determine their peak statistics and were compared with cumulative peak maneuver-load distributions for fighter and transport aircraft in flight.

  15. Comparison of tangibly reinforced speech-reception and pure-tone thresholds of mentally retarded children.

    PubMed

    Weaver, N J; Wardell, F N; Martin, F N

    1979-03-01

    Sixteen mentally retarded children who had normal hearing were examined with two tests of auditory sensitivity. One procedure employed a tangibly reinforced operant-conditioning paradigm for pure tones, and the other test was based on a modification of operant conditioning for obtaining speech-reception thresholds. The speech procedure, utilizing an attractive mechanical device in the form of a clown, proved to be effective and efficient for use with retarded children. PMID:426010

  16. Comparison of tangibly reinforced speech-reception and pure-tone thresholds of mentally retarded children.

    PubMed

    Weaver, N J; Wardell, F N; Martin, F N

    1979-03-01

    Sixteen mentally retarded children who had normal hearing were examined with two tests of auditory sensitivity. One procedure employed a tangibly reinforced operant-conditioning paradigm for pure tones, and the other test was based on a modification of operant conditioning for obtaining speech-reception thresholds. The speech procedure, utilizing an attractive mechanical device in the form of a clown, proved to be effective and efficient for use with retarded children.

  17. 14 CFR 23.521 - Water load conditions.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Water load conditions. 23.521 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23.521 Water load conditions. (a) The structure of seaplanes and amphibians must be designed for...

  18. 14 CFR 23.521 - Water load conditions.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Water load conditions. 23.521 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23.521 Water load conditions. (a) The structure of seaplanes and amphibians must be designed for...

  19. 14 CFR 23.521 - Water load conditions.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Water load conditions. 23.521 Section 23... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23.521 Water load conditions. (a) The structure of seaplanes and amphibians must be designed for...

  20. 14 CFR 23.525 - Application of loads.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Application of loads. 23.525 Section 23.525 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23.525 Application of loads. (a)...

  1. 14 CFR 23.525 - Application of loads.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Application of loads. 23.525 Section 23.525 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23.525 Application of loads. (a)...

  2. 14 CFR 23.395 - Control system loads.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Control Surface and System Loads § 23.395 Control system loads. (a) Each flight control system and its supporting structure must be... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Control system loads. 23.395 Section...

  3. 14 CFR 23.395 - Control system loads.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Control Surface and System Loads § 23.395 Control system loads. (a) Each flight control system and its supporting structure must be... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Control system loads. 23.395 Section...

  4. 14 CFR 23.395 - Control system loads.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Control Surface and System Loads § 23.395 Control system loads. (a) Each flight control system and its supporting structure must be... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Control system loads. 23.395 Section...

  5. 14 CFR 23.395 - Control system loads.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Control Surface and System Loads § 23.395 Control system loads. (a) Each flight control system and its supporting structure must be... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Control system loads. 23.395 Section...

  6. Combined load test apparatus for flat panels

    NASA Astrophysics Data System (ADS)

    McWithey, Robert R.; Martin, Carl J., Jr.; Cerro, Jeffrey A.

    1992-04-01

    Future hypersonic aircraft such as the National Aero-Space Plane and a high speed civil transport will require the design and use of efficient, highly-loaded, flat structural panels to achieve mission requirements. These panels will be subjected to severe combinations of in-plane mechanical distributed loads (i.e., normal loads in two perpendicular directions plus a shear load), in addition to pressure and thermal loads. A testing apparatus is provided for applying uniform combined in-plane stresses to a flat panel containing an interior test area. Actuators cause two sets of load rods to apply loads to the edge of the flat panel. The first set applies loads which are perpendicular to and independent of the loads applied by the second set. The loads are applied according to a cosine load distribution to obtain a uniform stress field within the test area. The flat panel may be rotated with respect to the applied loads to obtain a wide range of combined stresses in the test area. Movement outside the plane of the flat panel may be selectively prevented by connecting the flat panel to a restraining disk by support rods. The support rods then define the test area. A thermal load may be applied to one side of the flat panel and a pressure load may be applied to the other side. The novelty of this method is found in providing a testing apparatus which allows mechanical, thermal and pressure loads to be applied simultaneously to a flat panel for testing purposes.

  7. Accelerating degradation rate of pure iron by zinc ion implantation.

    PubMed

    Huang, Tao; Zheng, Yufeng; Han, Yong

    2016-12-01

    Pure iron has been considered as a promising candidate for biodegradable implant applications. However, a faster degradation rate of pure iron is needed to meet the clinical requirement. In this work, metal vapor vacuum arc technology was adopted to implant zinc ions into the surface of pure iron. Results showed that the implantation depth of zinc ions was about 60 nm. The degradation rate of pure iron was found to be accelerated after zinc ion implantation. The cytotoxicity tests revealed that the implanted zinc ions brought a slight increase on cytotoxicity of the tested cells. In terms of hemocompatibility, the hemolysis of zinc ion implanted pure iron was lower than 2%. However, zinc ions might induce more adhered and activated platelets on the surface of pure iron. Overall, zinc ion implantation can be a feasible way to accelerate the degradation rate of pure iron for biodegradable applications. PMID:27482462

  8. Accelerating degradation rate of pure iron by zinc ion implantation

    PubMed Central

    Huang, Tao; Zheng, Yufeng; Han, Yong

    2016-01-01

    Pure iron has been considered as a promising candidate for biodegradable implant applications. However, a faster degradation rate of pure iron is needed to meet the clinical requirement. In this work, metal vapor vacuum arc technology was adopted to implant zinc ions into the surface of pure iron. Results showed that the implantation depth of zinc ions was about 60 nm. The degradation rate of pure iron was found to be accelerated after zinc ion implantation. The cytotoxicity tests revealed that the implanted zinc ions brought a slight increase on cytotoxicity of the tested cells. In terms of hemocompatibility, the hemolysis of zinc ion implanted pure iron was lower than 2%. However, zinc ions might induce more adhered and activated platelets on the surface of pure iron. Overall, zinc ion implantation can be a feasible way to accelerate the degradation rate of pure iron for biodegradable applications. PMID:27482462

  9. Stable pure state quantum tomography from five orthonormal bases

    NASA Astrophysics Data System (ADS)

    Carmeli, Claudio; Heinosaari, Teiko; Kech, Michael; Schultz, Jussi; Toigo, Alessandro

    2016-08-01

    For any finite-dimensional Hilbert space, we construct explicitly five orthonormal bases such that the corresponding measurements allow for efficient tomography of an arbitrary pure quantum state. This means that such measurements can be used to distinguish an arbitrary pure state from any other state, pure or mixed, and the pure state can be reconstructed from the outcome distribution in a feasible way. The set of measurements we construct is independent of the unknown state, and therefore our results provide a fixed scheme for pure state tomography, as opposed to the adaptive (state-dependent) scheme proposed by Goyeneche et al. (Phys. Rev. Lett., 115 (2015) 090401). We show that our scheme is robust with respect to noise, in the sense that any measurement scheme which approximates these measurements well enough is equally suitable for pure state tomography. Finally, we present two convex programs which can be used to reconstruct the unknown pure state from the measurement outcome distributions.

  10. AgraPure Mississippi Biomass Project

    SciTech Connect

    Blackwell,D.A; Broadhead, L.W.; Harrell, W.J.

    2006-03-31

    The AgraPure Mississippi Biomass project was a congressionally directed project, initiated to study the utilization of Mississippi agricultural byproducts and waste products in the production of bio-energy and to determine the feasibility of commercialization of these agricultural byproducts and waste products as feedstocks in the production of energy. The final products from this project were two business plans; one for a Thermal plant, and one for a Biodiesel/Ethanol plant. Agricultural waste fired steam and electrical generating plants and biodiesel plants were deemed the best prospects for developing commercially viable industries. Additionally, oil extraction methods were studied, both traditional and two novel techniques, and incorporated into the development plans. Mississippi produced crop and animal waste biomasses were analyzed for use as raw materials for both industries. The relevant factors, availability, costs, transportation, storage, location, and energetic value criteria were considered. Since feedstock accounts for more than 70 percent of the total cost of producing biodiesel, any local advantages are considered extremely important in developing this particular industry. The same factors must be evaluated in assessing the prospects of commercial operation of a steam and electrical generation plant. Additionally, the access to the markets for electricity is more limited, regulated and tightly controlled than the liquid fuel markets. Domestically produced biofuels, both biodiesel and ethanol, are gaining more attention and popularity with the consuming public as prices rise and supplies of foreign crude become less secure. Biodiesel requires no major modifications to existing diesel engines or supply chain and offers significant environmental benefits. Currently the biodiesel industry requires Federal and State incentives to allow the industry to develop and become self-sustaining. Mississippi has available the necessary feedstocks and is

  11. The effects of fuel volatility, structure, speed and load on hydrocarbon emissions from piston wetting in direct injection spark ignition engines

    NASA Astrophysics Data System (ADS)

    Huang, Yiqun

    Piston wetting can be isolated from the other sources of hydrocarbon (HC) emissions from DISI engines by operating the engine predominantly on a gaseous fuel and using an injector probe to impact a small amount of liquid fuel on the piston top. This results in a marked increase in HC emissions. In the present study, a variety of pure liquid hydrocarbons are used to examine the influence of fuel volatility, structure, speed and load. The exhaust hydrocarbons were speciated to differentiate between the emissions resulting from the gaseous fuel and those resulting from the liquid fuel. It was shown that the HC emissions correspond to the Leidenfrost effect: fuels with very low boiling points yield high HCs and those with a boiling point near or above the piston temperature produce much lower HCs. To examine the fuel volatility and structure effects, tests of a matrix of nine pure liquid hydrocarbon fuels, including normal-alkanes, iso-alkanes, cyclo-alkanes and aromatics, were performed at a single operating condition: the Ford World Wide Mapping Point (WWMP). The effects of engine speed and load were also examined. For these tests, four different normal alkanes were used, including one that appears to be near the Leidenfrost point for operation at the WWMP, one that is near the Nukiyama point, and one that appears to be in the transition region. It is shown that the "Piston Wetting Emissions Index" for engine-out total hydrocarbon emissions increases with both decreasing speed and decreasing load, and that this is primarily an effect of oxidation kinetics. Speed and load have opposite effects on unburned fuel emissions, and this appears to be a pressure effect. For all speeds and loads the Leidenfrost effect appears to be important: the most volatile fuel has the highest total hydrocarbon and unburned fuel emissions whereas the two least volatile fuels have lower emissions and the fuel that is within the transition regime yields intermediate emissions.

  12. Contact forces at the sliding interface: Mixed versus pure model alkane monolayers

    NASA Astrophysics Data System (ADS)

    Mikulski, Paul T.; Gao, Guangtu; Chateauneuf, Ginger M.; Harrison, Judith A.

    2005-01-01

    Classical molecular dynamics simulations of an amorphous carbon tip sliding against monolayers of n-alkane chains are presented. The tribological behavior of tightly packed, pure monolayers composed of chains containing 14 carbon atoms is compared to mixed monolayers that randomly combine equal amounts of 12- and 16-carbon-atom chains. When sliding in the direction of chain cant under repulsive (positive) loads, pure monolayers consistently show lower friction than mixed monolayers. The distribution of contact forces between individual monolayer chain groups and the tip shows pure and mixed monolayers resist tip motion similarly. In contrast, the contact forces "pushing" the tip along differ in the two monolayers. The pure monolayers exhibit a high level of symmetry between resisting and pushing forces which results in a lower net friction. Both systems exhibit a marked friction anisotropy. The contact force distribution changes dramatically as a result of the change in sliding direction, resulting in an increase in friction. Upon continued sliding in the direction perpendicular to chain cant, both types of monolayers are often capable of transitioning to a state where the chains are primarily oriented with the cant along the sliding direction. A large change in the distribution of contact forces and a reduction in friction accompany this transition.

  13. Memory for pure tone sequences without contour.

    PubMed

    Lefebvre, Christine; Jolicœur, Pierre

    2016-06-01

    We presented pure tones interspersed with white noise sounds to disrupt contour perception in an acoustic short-term memory (ASTM) experiment during which we recorded the electroencephalogram. The memory set consisted of seven stimuli, 0, 1, 2, 3, or 4 of which were to-be-remembered tones. We estimated each participant׳s capacity, K, for each set size and measured the amplitude of the SAN (sustained anterior negativity, an ERP related to acoustic short-term memory). We correlated their K slopes with their SAN amplitude slopes as a function of set size, and found a significant link between performance and the SAN: a larger increase in SAN amplitude was linked with a larger number of stimuli maintained in ASTM. The SAN decreased in amplitude in the later portion of the silent retention interval, but the correlation between the SAN and capacity remained strong. These results show the SAN is not an index of contour but rather an index of the maintenance of individual objects in STM. This article is part of a Special Issue entitled SI: Auditory working memory. PMID:26903419

  14. Electron Acoustic Waves in Pure Ion Plasmas

    NASA Astrophysics Data System (ADS)

    Anderegg, F.; Affolter, M.; Driscoll, C. F.; O'Neil, T. M.; Valentini, F.

    2012-10-01

    Electron Acoustic Waves (EAWs) are the low-frequency branch of near-linear Langmuir (plasma) waves: the frequency is such that the complex dielectric function (Dr, Di) has Dr= 0; and ``flattening'' of f(v) near the wave phase velocity vph gives Di=0 and eliminates Landau damping. Here, we observe standing axisymmetric EAWs in a pure ion column.footnotetextF. Anderegg, et al., Phys. Rev. Lett. 102, 095001 (2009). At low excitation amplitudes, the EAWs have vph˜1.4 v, in close agreement with near-linear theory. At moderate excitation strengths, EAW waves are observed over a range of frequencies, with 1.3 v < vph< 2.1 v. Here, the final wave frequency may differ from the excitation frequency since the excitation modifies f (v); and recent theory analyzes frequency shifts from ``corners'' of a plateau at vph.footnotetextF. Valentini et al., arXiv:1206.3500v1. Large amplitude EAWs have strong phase-locked harmonic content, and experiments will be compared to same-geometry simulations, and to simulations of KEENfootnotetextB. Afeyan et al., Proc. Inertial Fusion Sci. and Applications 2003, A.N.S. Monterey (2004), p. 213. waves in HEDLP geometries.

  15. Peccei-Quinn symmetric pure gravity mediation

    NASA Astrophysics Data System (ADS)

    Evans, Jason L.; Ibe, Masahiro; Olive, Keith A.; Yanagida, Tsutomu T.

    2014-07-01

    Successful models of pure gravity mediation (PGM) with radiative electroweak symmetry breaking can be expressed with as few as two free parameters, which can be taken as the gravitino mass and . These models easily support a 125-126 GeV Higgs mass at the expense of a scalar spectrum in the multi-TeV range and a much lighter wino as the lightest supersymmetric particle. In these models, it is also quite generic that the Higgs mixing mass parameter, , which is determined by the minimization of the Higgs potential is also in the multi-TeV range. For , the thermal relic density of winos is too small to account for the dark matter. The same is true for unless the gravitino mass is of order 500 TeV. Here, we consider the origin of a multi-TeV parameter arising from the breakdown of a Peccei-Quinn (PQ) symmetry. A coupling of the PQ-symmetry breaking field, , to the MSSM Higgs doublets, naturally leads to a value of TeV and of the order that is required in PGM models. In this case, axions make up the dark matter or some fraction of the dark matter with the remainder made up from thermal or non-thermal winos. We also provide solutions to the problem of isocurvature fluctuations with axion dark matter in this context.

  16. Foaming of mixtures of pure hydrocarbons

    NASA Technical Reports Server (NTRS)

    Robinson, J. V.; Woods, W. W.

    1950-01-01

    Mixtures of pure liquid hydrocarbons are capable of foaming. Nine hydrocarbons were mixed in pairs, in all possible combinations, and four proportions of each combination. These mixtures were sealed in glass tubes, and the foaming was tested by shaking. Mixtures of aliphatic with other aliphatic hydrocarbons, or of alkyl benzenes with other alkyl benzenes, did not foam. Mixtures of aliphatic hydrocarbons with alkyl benzenes did foam. The proportions of the mixtures greatly affected the foaming, the maximum foaming of 12 of 20 pairs being at the composition 20 percent aliphatic hydrocarbon, 80 percent alkyl benzene. Six seconds was the maximum foam lifetime of any of these mixtures. Aeroshell 120 lubricating oil was fractionated into 52 fractions and a residue by extraction with acetone in a fractionating extractor. The index of refraction, foam lifetime, color, and viscosity of these fractions were measured. Low viscosity and high index fractions were extracted first. The viscosity of the fractions extracted rose and the index decreased as fractionation proceeded. Foam lifetimes and color were lowest in the middle fractions. Significance is attached to the observation that none of the foam lifetimes of the fractions or residue is as high as the foam lifetime of the original Aeroshell, indicating that the foaming is not due to a particular foaming constituent, but rather to the entire mixture.

  17. Memory for pure tone sequences without contour.

    PubMed

    Lefebvre, Christine; Jolicœur, Pierre

    2016-06-01

    We presented pure tones interspersed with white noise sounds to disrupt contour perception in an acoustic short-term memory (ASTM) experiment during which we recorded the electroencephalogram. The memory set consisted of seven stimuli, 0, 1, 2, 3, or 4 of which were to-be-remembered tones. We estimated each participant׳s capacity, K, for each set size and measured the amplitude of the SAN (sustained anterior negativity, an ERP related to acoustic short-term memory). We correlated their K slopes with their SAN amplitude slopes as a function of set size, and found a significant link between performance and the SAN: a larger increase in SAN amplitude was linked with a larger number of stimuli maintained in ASTM. The SAN decreased in amplitude in the later portion of the silent retention interval, but the correlation between the SAN and capacity remained strong. These results show the SAN is not an index of contour but rather an index of the maintenance of individual objects in STM. This article is part of a Special Issue entitled SI: Auditory working memory.

  18. Pure inorganic separator for lithium ion batteries.

    PubMed

    He, Meinan; Zhang, Xinjie; Jiang, Kuiyang; Wang, Joe; Wang, Yan

    2015-01-14

    Battery safety is critical for many applications including portable electronics, hybrid and electric vehicles, and grid storage. For lithium ion batteries, the conventional polymer based separator is unstable at 120 °C and above. In this research, we have developed a pure aluminum oxide nanowire based separator; this separator does not contain any polymer additives or binders; additionally, it is a bendable ceramic. The physical and electrochemical properties of the separator are investigated. The separator has a pore size of about 100 nm, and it shows excellent electrochemical properties under both room and high temperatures. At room temperature, the ceramic separator shows a higher rate capability compared to the conventional Celgard 2500 separator and life cycle performance does not show any degradation. At 120 °C, the cell with the ceramic separator showed a much better cycle performance than the conventional Celgard 2500 separator. Therefore, we believe that this research is really an exciting scientific breakthrough for ceramic separators and lithium ion batteries and could be potentially used in the next generation lithium ion batteries requiring high safety and reliability.

  19. Shifting from preconceptions to pure wonderment.

    PubMed

    Porr, Caroline

    2005-07-01

    The author reflects upon her role as a public health nurse striving to attain practice authenticity. Client assessment and nursing interventions were seemingly sufficient until she became curious about 'Who is this person sitting across from me?' and 'What are her experiences in the world as a lone parent living in poverty at the margins of society?' The author begins to think that she could shift from mere client investigation to pure wonderment about the Other by imagining herself as a researcher, an explorer of another's life world. Ultimately this process enables her to enhance the 'caring' in her practice with the knowledge gained of the perceptions and meanings impoverished clients assigned to their everyday lives. Jurgen Habermas' theory of communicative competence serves as the reference map guiding exploration. The author uses Habermas' theoretical principles of intersubjective mutuality--the validity claims of comprehensibility, truth, sincerity, and legitimacy. Comprehensibility embodies understanding, an attitude of unconditional acceptance, and care respect of another's individual person and self-defined reality. Intersubjective mutuality also requires that one dwell in the moment with the Other, satisfied that communication is founded on truth. Sincerity implies fostering the Other's expression of authentic self apart from oppressive distracters. Lastly, legitimacy reconciles the author's altruistic pursuit to know the Other's ontological truth with the reality of the present world.

  20. Calibration of sound velocimeter in pure water

    NASA Astrophysics Data System (ADS)

    Li, Zhiwei; Zhang, Baofeng; Li, Tao; Zhu, Junchao; Xie, Ziming

    2016-01-01

    Accurate measurement of sound speed is important to calibrate a sound velocity profiler which provides real-time sound velocity to the sonar equipment in oceanographic survey. The sound velocity profiler calculates the sound speed by measuring the time-of-flight of a 1 MHz single acoustic pulse to travel over about 300 mm path. A standard sound velocimeter instrument was invited to calibrate the sound velocity profiler in pure water at temperatures of 278,283, 288, 293, 298, 303 and 308K in a thermostatic vessel at one atmosphere. The sound velocity profiler was deployed in the thermostatic vessel alongside the standard sound velocimeter instrument and two platinum resistance thermometers (PRT) which were calibrated to 0.002k by comparison with a standard PRT. Time of flight circuit board was used to measure the time-of-flight to 22 picosecond precision. The sound speed which was measured by the sound velocity profiler was compared to the standard sound speed calculated by UNESCO to give the laboratory calibration coefficients and was demonstrated agreement with CTD-derived sound speed using Del Grosso's seawater equation after removing a bias.

  1. Localization of aerial pure tones by pinnipeds

    NASA Astrophysics Data System (ADS)

    Holt, Marla M.; Schusterman, Ronald J.; Kastak, David; Southall, Brandon L.

    2005-12-01

    In this study, minimum audible angles (MAAs) of aerial pure tones were measured in and compared between a northern elephant seal (Mirounga angustirostris), a harbor seal (Phoca vitulina), and a California sea lion (Zalophus californianus). Testing was conducted between 0.8 and 16 kHz in the elephant seal and 0.8 and 20 kHz in the harbor seal and sea lion in a hemi-anechoic chamber using a left/right psychophysical procedure. Performance for the same frequencies was also quantified for discrete speaker separation of 5° from the mid-line. For all subjects, MAAs ranged from approximately 3° to 15° and were generally equal to or larger than those previously measured in the same subjects with a broadband signal. Performance at 5° ranged from chance to 97% correct, depending on frequency and subject. Poorest performance in the sea lion and harbor seal occurred at intermediate frequencies, which is consistent with the duplex theory of sound localization. In contrast, the elephant seal's poorest performance occurred at higher frequencies. The elephant seal's result suggests an inferior ability to utilize interaural level differences and is perhaps related to best hearing sensitivity shifted toward lower frequencies in this species relative to other pinnipeds.

  2. Photoionization Dynamics in Pure Helium Droplets

    SciTech Connect

    Peterka, Darcy S.; Kim, Jeong Hyun; Wang, Chia C.; Poisson,Lionel; Neumark, Daniel M.

    2007-02-04

    The photoionization and photoelectron spectroscopy of pure He droplets are investigated at photon energies between 24.6 eV (the ionization energy of He) and 28 eV. Time-of-flight mass spectra and photoelectron images were obtained at a series of molecular beam source temperatures and pressures to assess the effect of droplet size on the photoionization dynamics. At source temperatures below 16 K, the photoelectron images are dominated by fast electrons produced via direct ionization of He atoms, with a small contribution from very slow electrons with kinetic energies below 1 meV arising from an indirect mechanism. The fast photoelectrons have as much as 0.5 eV more kinetic energy than those from atomic He at the same photon energy. This result is interpreted and simulated within the context of a 'dimer model', in which one assumes vertical ionization from two nearest neighbor He atoms to the attractive region of the He2+ potential energy curve. Possible mechanism for the slow electrons, which were also seen at energies below IE(He), are discussed, including vibrational autoionizaton of Rydberg states comprising an electron weakly bound to the surface of a large HeN+ core.

  3. Peak load management: Potential options

    SciTech Connect

    Englin, J.E.; De Steese, J.G.; Schultz, R.W.; Kellogg, M.A.

    1989-10-01

    This report reviews options that may be alternatives to transmission construction (ATT) applicable both generally and at specific locations in the service area of the Bonneville Power Administration (BPA). Some of these options have potential as specific alternatives to the Shelton-Fairmount 230-kV Reinforcement Project, which is the focus of this study. A listing of 31 peak load management (PLM) options is included. Estimated costs and normalized hourly load shapes, corresponding to the respective base load and controlled load cases, are considered for 15 of the above options. A summary page is presented for each of these options, grouped with respect to its applicability in the residential, commercial, industrial, and agricultural sectors. The report contains comments on PLM measures for which load shape management characteristics are not yet available. These comments address the potential relevance of the options and the possible difficulty that may be encountered in characterizing their value should be of interest in this investigation. The report also identifies options that could improve the efficiency of the three customer utility distribution systems supplied by the Shelton-Fairmount Reinforcement Project. Potential cogeneration options in the Olympic Peninsula are also discussed. These discussions focus on the options that appear to be most promising on the Olympic Peninsula. Finally, a short list of options is recommended for investigation in the next phase of this study. 9 refs., 24 tabs.

  4. Self-normalized photothermal techniques for thermal diffusivity measurements

    NASA Astrophysics Data System (ADS)

    Balderas-López, J. A.; Mandelis, A.

    2000-12-01

    Two self-normalized photothermal techniques, to carry out thermal diffusivity measurements of condensed phase materials, are presented. These simple methodologies involve linear fitting procedures of the signal amplitude and phase. These procedures lead to the elimination of the usual requirement for instrumental transfer-function normalization. The thermal diffusivities for two dental resins and two pure liquids are measured with these simple methodologies and very good agreement is found with values reported in the literature, where more involved analysis is usually required.

  5. Nanosecond square pulse generation in fiber lasers with normal dispersion

    NASA Astrophysics Data System (ADS)

    Zhao, L. M.; Tang, D. Y.; Cheng, T. H.; Lu, C.

    2007-04-01

    We report on the generation of nanosecond square pulses in a passively mode-locked fiber ring laser made of purely normal dispersive fibers. Different to the noise-like pulse operation of the laser, the generated square pulses are stable and have no internal structures. We show that the formation of the square pulse is due to the combined action of the pulse peak clamping effect caused by the cavity and the almost linear pulse propagation in the normal dispersive fibers.

  6. The evolution of pure alexia: a longitudinal study of recovery.

    PubMed

    Behrmann, M; Black, S E; Bub, D

    1990-10-01

    This case report documents the partial recovery, over a 12-month period, of pure alexia in an adult female following a left occipital infarction. Measures of speed and accuracy were obtained on an oral reading and a lexical decision task immediately postonset and then on 10 subsequent occasions. Explicit letter-by-letter reading was observed only during the first week poststroke but a significant effect of word length was seen in all testing sessions. Reading accuracy was relatively good at all stages and reading latency showed a remarkable decrease over time but did not reach normal reading rates. The inability to use higher-order orthographic knowledge, as manifest in the absence of a word superiority effect, was still noted at one year postonset. We therefore concluded that the change in behavior was attributable to increased proficiency in the use of the adaptive letter-by-letter procedure rather than to the resolution of the underlying deficit. It is suggested that longitudinal neurobehavioral studies add to our understanding of the alexic deficit and provide insight into the recovery process. PMID:2285860

  7. Lubrication and load-bearing properties of human salivary pellicles adsorbed ex vivo on molecularly smooth substrata.

    PubMed

    Harvey, Neale M; Yakubov, Gleb E; Stokes, Jason R; Klein, Jacob

    2012-01-01

    In a series of Surface Force Balance experiments, material from human whole saliva was adsorbed to molecularly smooth mica substrata (to form an 'adsorbed salivary film'). Measurements were taken of normal (load bearing, F (n)) and shear (frictional, F (s)*) forces between two interacting surfaces. One investigation involved a salivary film formed by overnight adsorption from undiluted, centrifuged saliva, with the adsorbed film rinsed with pure water before measurement. Measurements were taken under pure water and 70 mM NaNO(3). In a second investigation, a film was formed from and measured under a solution of 7% filtered saliva in 10 mM NaNO(3). F (n) results for both systems showed purely repulsive layers, with an uncompressed thickness of 35-70 nm for the diluted saliva investigation and, prior to the application of shear, 11 nm for the rinsed system. F (s)* was essentially proportional to F (n) for all systems and independent of shear speed (in the range 100-2000 nm s(-1)), with coefficients of friction μ ≈ 0.24 and μ ≈ 0.46 for the unrinsed and rinsed systems, respectively. All properties of the rinsed system remained similar when the pure water measurement environment was changed to 70 mM NaNO(3). For all systems studied, shear gave rise to an approximately threefold increase in the range of normal forces, attributed to the ploughing up of adsorbed material during shear to form debris that stood proud of the adsorbed layer. The results provide a microscopic demonstration of the wear process for a salivary film under shear and may be of particular interest for understanding the implications for in vivo oral lubrication under conditions such as rinsing of the mouth cavity. The work is interpreted in light of earlier studies that showed a structural collapse and increase in friction for an adsorbed salivary film in an environment of low ionic strength.

  8. Characterizing commercial pureed foods: sensory, nutritional, and textural analysis.

    PubMed

    Ettinger, Laurel; Keller, Heather H; Duizer, Lisa M

    2014-01-01

    Dysphagia (swallowing impairment) is a common consequence of stroke and degenerative diseases such as Parkinson's and Alzheimer's. Limited research is available on pureed foods, specifically the qualities of commercial products. Because research has linked pureed foods, specifically in-house pureed products, to malnutrition due to inferior sensory and nutritional qualities, commercial purees also need to be investigated. Proprietary research on sensory attributes of commercial foods is available; however direct comparisons of commercial pureed foods have never been reported. Descriptive sensory analysis as well as nutritional and texture analysis of commercially pureed prepared products was performed using a trained descriptive analysis panel. The pureed foods tested included four brands of carrots, of turkey, and two of bread. Each commercial puree was analyzed for fat (Soxhlet), protein (Dumas), carbohydrate (proximate analysis), fiber (total fiber), and sodium content (Quantab titrator strips). The purees were also texturally compared with a line spread test and a back extrusion test. Differences were found in the purees for sensory attributes as well as nutritional and textural properties. Findings suggest that implementation of standards is required to reduce variability between products, specifically regarding the textural components of the products. This would ensure all commercial products available in Canada meet standards established as being considered safe for swallowing.

  9. The Normalized Child.

    ERIC Educational Resources Information Center

    Futrell, Kathleen H.

    1997-01-01

    Describes characteristics of the normalized child, the ultimate goal of Montessori education. First outlines children's basic needs, then describes traits of the normalized child, including love of order, work, silence and working alone; mutual aid and cooperation; profound spontaneous concentration; obedience; independence and initiative;…

  10. Pure-phase and pure-amplitude hologram design using the method of generalized projections

    NASA Astrophysics Data System (ADS)

    Catino, William Charles

    The overall contribution of the research presented in this dissertation is a systematic procedure for designing computer-generated holograms subject to far-field image constraints. The method of generalized projections is used to design pure-phase and pure-amplitude diffraction holograms that generate prescribed gray-scale images in the Fourier frequency plane. Performance is demonstrated with objective measures (error, efficiency, and variance), as well as with subjective comparison of images. Test images include a photographic quality image of Lena, a uniform intensity spot array, and a binary amplitude block text image. Projection algorithms are derived for pure-phase holograms with both continuous and quantized phase characteristics from a prescribed far-field magnitude constraint. The performance of the pure-phase hologram designs, as measured in the far-field image, is always very good for the continuous phase case and for the quantized phase case with a large number of phase quantization levels. However, as the number of quantization levels decreases, the performance typically degrades. Performance is significantly improved by constraining the energy in mutually exclusive cliques, that is, groups of image plane (far-field) pixels, instead of constraining the intensity of each individual pixel. Even for the binary phase case, acceptable images are generated with the clique energy algorithm. The method of generalized projections is also used to design pure-amplitude diffraction holograms using a prescribed image intensity constraint. Two algorithms are derived: the direct method, which nonlinearly constrains the hologram transmittance to the range of real values in (0,1); and the indirect method, which constrains the transmittance values to the real axis, and linearly transforms the resulting values to the range (0,1). Digital amplitude holograms are simulated by quantizing the amplitude holograms resulting from the indirect method. The indirect method

  11. Analysis of Square Cup Deep-Drawing Test of Pure Titanium

    NASA Astrophysics Data System (ADS)

    Ogawa, Takaki; Ma, Ninshu; Ueyama, Minoru; Harada, Yasunori

    2016-08-01

    The prediction of formability of titunium is more difficult than steels since its strong anisotropy. If computer simulation can estimate the formability of titanium, we can select the optimal forming conditions. The purpose of this study was to acquire knowledge for the formability prediction by the computer simulation of the square cup deep-drawing of pure titanium. In this paper, the results of FEM analsis of pure titanium were compared with the experimental results to examine the analysis validity. We analyzed the formability of deepdrawing square cup of titanium by the FEM using solid elements. Compared the analysis results with the experimental results such as the forming shape, the punch load, and the thickness, the validity was confirmed. Further, through analyzing the change of the thickness around the forming corner, it was confirmed that the thickness increased to its maximum value during forming process at the stroke of 35mm more than the maximum stroke.

  12. Pure bending of a solid cone

    NASA Astrophysics Data System (ADS)

    Renton, J. D.

    1997-05-01

    The problems of torsion, axial loading and shear of a solid cone were solved around the turn of the century by Michell and Föppl. Surprisingly, no solution to the problem of the elastic response of a cone to the only other possible resultant applied to its apex seems to have been published until now. The method used here is based on certain theoretical considerations related to the author's work on generalizing the engineering theory of beams. This means that the result is derived rather than being the result of a trial-and-error process. A comparison is made with the usual engineering theory as modified for variable bending stiffness. The two analyses give the same results at the limit as the cone angle tends to zero.

  13. Pure Java-based streaming MPEG player

    NASA Astrophysics Data System (ADS)

    Tolba, Osama; Briceno, Hector; McMillan, Leonard

    1999-01-01

    We present a pure Java-based streaming MPEG-1 video player. By implementing the player entirely in Java, we guarantee its functionality across platforms within any Java-enabled web browsers, without the need for native libraries. This allows greater sue of MPEG video sequences, because the users will no longer need to pre-install any software to display video, beyond Java compatibility. This player features a novel forward-mapping IDCT algorithm that allows it to play locally stored, CIF-sized video sequences at 11 frames per second, when run on a personal computer with Java 'just-in-time' compiler. The IDCT algorithm can run with greater speed when the sequence is viewed at reduced size; e.g., performing approximately 1/4 the amount of computation when the user resizes the sequence to 1/2 its original width and height. We are able to play video streams stored anywhere on the Internet with acceptable performance using a proxy server, eliminating the need for large-capacity auxiliary storage. Thus, the player is well suited to small devices, such as digital TV set-top decoders, requiring little more memory than is required for three video frames. Because of our modular design, it is possible to assemble multiple video streams from remote sources and present them simultaneously to the viewers, subject to network and local performance limitations. The same modular system can further provide viewers with their own customized view of each sessions; e.g., moving and resizing the video display window dynamically, and selecting their preferred set of video controls.

  14. Predictions of pure liquid shock Hugoniots

    SciTech Connect

    Hobbs, M.L.; Baer, M.R.

    1998-06-01

    Determination of product species and associated equations-of-state (EOS) for energetic materials such as pyrotechnics with complex elemental compositions remains a major unsolved problem. Although, empirical EOS models may be calibrated to replicate detonation conditions within experimental variability (5--10%), different states, e.g. expansion, may produce significant discrepancy with data if the basic form of the EOS model is incorrect. A more physically realistic EOS model based on intermolecular potentials, such as the Jacobs Cowperthwaite Zwisler (JCZ3) EOS, is needed to predict detonation states as well as expanded states. Predictive capability for any EOS requires a large species data base composed of a wide variety of elements. Unfortunately, only 20 species have known exponential 6 (EXP 6) molecular force constants which are used in the JCZ3-EOS. Of these 20 species, only 10 have been adequately compared to experimental data such as molecular scattering or shock Hugoniot data. Since data in the strongly repulsive region of the molecular potential is limited, alternative methods must be found to deduce force constants for a larger number of species. The objective of the present study is to determine JCZ3 product species force constants using corresponding state theory. Intermolecular potential parameters were obtained for a variety of gas species using a simple corresponding states technique with critical volume and critical temperature. A more complex, four parameter corresponding state method with shape and polarity corrections was also used to obtain intermolecular potential parameters. Both corresponding state methods were used to predict shock Hugoniot data obtained from pure liquids. The simple corresponding state method is shown to give adequate agreement with shock Hugoniot data.

  15. Improved Design Formulae for Buckling of Orthotropic Plates under Combined Loading

    NASA Technical Reports Server (NTRS)

    Weaver, Paul M.; Nemeth, Michael P.

    2008-01-01

    Simple, accurate buckling interaction formulae are presented for long orthotropic plates with either simply supported or clamped longitudinal edges and under combined loading that are suitable for design studies. The loads include 1) combined uniaxial compression (or tension) and shear, 2) combined pure inplane bending and 3) shear and combined uniaxial compression (or tension) and pure inplane bending. The interaction formulae are the results of detailed regression analysis of buckling data obtained from a very accurate Rayleigh-Ritz method.

  16. Improved H2S and Cl2 Sensing Characteristics of Pure and Au Incorporated WO3 Thin Films

    NASA Astrophysics Data System (ADS)

    Ramgir, Niranjan S.; Ganapathi, S. Kailasa; Kaur, M.; Mishra, S.; Datta, N.; Aswal, D. K.; Gupta, S. K.; Yakhmi, J. V.

    2011-07-01

    Gas sensing properties of pure and Au incorporated WO3 thin films towards H2S and Cl2 have been investigated. The sensor films were able to detect H2S and Cl2 selectively at an operating temperature of 150 and 200 °C, respectively. Effect of gas concentration and Au loading have been investigated and correlated with the observed sensitivity values. Pure WO3 films exhibited better sensing characteristics towards H2S (S = 17, 10 ppm, 150 °C) while sensor film containing Au thickness of 21.6 nm exhibited a maximum sensitivity towards Cl2 (S = 89, 10 ppm, 200 °C)..

  17. Entanglement bound for multipartite pure states based on local measurements

    SciTech Connect

    Jiang Lizhen; Chen Xiaoyu; Ye Tianyu

    2011-10-15

    An entanglement bound based on local measurements is introduced for multipartite pure states. It is the upper bound of the geometric measure and the relative entropy of entanglement. It is the lower bound of the minimal-measurement entropy. For pure bipartite states, the bound is equal to the entanglement entropy. The bound is applied to pure tripartite qubit states and the exact tripartite relative entropy of entanglement is obtained for a wide class of states.

  18. Typical pure nonequilibrium steady states and irreversibility for quantum transport.

    PubMed

    Monnai, Takaaki; Yuasa, Kazuya

    2016-07-01

    It is known that each single typical pure state in an energy shell of a large isolated quantum system well represents a thermal equilibrium state of the system. We show that such typicality holds also for nonequilibrium steady states (NESS's). We consider a small quantum system coupled to multiple infinite reservoirs. In the long run, the total system reaches a unique NESS. We identify a large Hilbert space from which pure states of the system are to be sampled randomly and show that the typical pure states well describe the NESS. We also point out that the irreversible relaxation to the unique NESS is important to the typicality of the pure NESS's.

  19. Typical pure nonequilibrium steady states and irreversibility for quantum transport

    NASA Astrophysics Data System (ADS)

    Monnai, Takaaki; Yuasa, Kazuya

    2016-07-01

    It is known that each single typical pure state in an energy shell of a large isolated quantum system well represents a thermal equilibrium state of the system. We show that such typicality holds also for nonequilibrium steady states (NESS's). We consider a small quantum system coupled to multiple infinite reservoirs. In the long run, the total system reaches a unique NESS. We identify a large Hilbert space from which pure states of the system are to be sampled randomly and show that the typical pure states well describe the NESS. We also point out that the irreversible relaxation to the unique NESS is important to the typicality of the pure NESS's.

  20. Normality in analytical psychology.

    PubMed

    Myers, Steve

    2013-12-01

    Although C.G. Jung's interest in normality wavered throughout his career, it was one of the areas he identified in later life as worthy of further research. He began his career using a definition of normality which would have been the target of Foucault's criticism, had Foucault chosen to review Jung's work. However, Jung then evolved his thinking to a standpoint that was more aligned to Foucault's own. Thereafter, the post Jungian concept of normality has remained relatively undeveloped by comparison with psychoanalysis and mainstream psychology. Jung's disjecta membra on the subject suggest that, in contemporary analytical psychology, too much focus is placed on the process of individuation to the neglect of applications that consider collective processes. Also, there is potential for useful research and development into the nature of conflict between individuals and societies, and how normal people typically develop in relation to the spectrum between individuation and collectivity.

  1. Normal Functioning Family

    MedlinePlus

    ... Spread the Word Shop AAP Find a Pediatrician Family Life Medical Home Family Dynamics Adoption & Foster Care ... Español Text Size Email Print Share Normal Functioning Family Page Content Article Body Is there any way ...

  2. Normal pressure hydrocephalus

    MedlinePlus

    Hydrocephalus - occult; Hydrocephalus - idiopathic; Hydrocephalus - adult; Hydrocephalus - communicating; Dementia - hydrocephalus; NPH ... Ferri FF. Normal pressure hydrocephalus. In: Ferri FF, ed. ... Elsevier; 2016:chap 648. Rosenberg GA. Brain edema and disorders ...

  3. Normality in Analytical Psychology

    PubMed Central

    Myers, Steve

    2013-01-01

    Although C.G. Jung’s interest in normality wavered throughout his career, it was one of the areas he identified in later life as worthy of further research. He began his career using a definition of normality which would have been the target of Foucault’s criticism, had Foucault chosen to review Jung’s work. However, Jung then evolved his thinking to a standpoint that was more aligned to Foucault’s own. Thereafter, the post Jungian concept of normality has remained relatively undeveloped by comparison with psychoanalysis and mainstream psychology. Jung’s disjecta membra on the subject suggest that, in contemporary analytical psychology, too much focus is placed on the process of individuation to the neglect of applications that consider collective processes. Also, there is potential for useful research and development into the nature of conflict between individuals and societies, and how normal people typically develop in relation to the spectrum between individuation and collectivity. PMID:25379262

  4. Efficient decomposition of cosmic microwave background polarization maps into pure E, pure B, and ambiguous components

    SciTech Connect

    Bunn, Emory F.

    2011-04-15

    Separation of the B component of a cosmic microwave background (CMB) polarization map from the much larger E component is an essential step in CMB polarimetry. For a map with incomplete sky coverage, this separation is necessarily hampered by the presence of ambiguous modes which could be either E or B modes. I present an efficient pixel-space algorithm for removing the ambiguous modes and separating the map into pure E and B components. The method, which works for arbitrary geometries, does not involve generating a complete basis of such modes and scales the cube of the number of pixels on the boundary of the map.

  5. Normal Variants in Echocardiography.

    PubMed

    Sanchez, Daniel R; Bryg, Robert J

    2016-11-01

    Echocardiography is a powerful and convenient tool used routinely in the cardiac evaluation of many patients. Improved resolution and visualization of cardiac anatomy has led to the discovery of many normal variant structures that have no known pathologic consequence. Importantly, these findings may masquerade as pathology prompting unnecessary further evaluation at the expense of anxiety, cost, or potential harm. This review provides an updated and comprehensive collection of normal anatomic variants on both transthoracic and transesophageal imaging. PMID:27612473

  6. FT-IR microspectroscopy in rapid identification of bacteria in pure and mixed culture

    NASA Astrophysics Data System (ADS)

    Fontoura, Inglid; Belo, Ricardo; Sakane, Kumiko; Cardoso, Maria Angélica Gargione; Khouri, Sônia; Uehara, Mituo; Raniero, Leandro; Martin, Airton A.

    2010-02-01

    In recent years FT-IR microspectroscopy has been developed for microbiology analysis and applied successfully in pure cultures of microorganisms to rapidly identify strains of bacteria, yeasts and fungi. The investigation and characterization of microorganism mixed cultures is also of growing importance, especially in hospitals where it is common to poly-microbial infections. In this work, the rapid identification of bacteria in pure and mixed cultures was studied. The bacteria were obtained from the Institute Oswaldo Cruz culture collection at Brazil. Escherichia coli ATCC 10799 and Staphylococcus aureus ATCC 14456 were analyzed, 3 inoculations were examined in triplicate: Escherichia coli, Staphylococcus aureus and a mixed culture of them. The inoculations were prepared according to McFarland 0.5, incubated at 37 ° C for 6 hours, diluted in saline, placed in the CaF2 window and store for one hour at 50°C to obtain thin film. The measurement was performed by Spectrum Spotlight 400 (Perkin-Elmer) equipment in the range of 4000-900 cm-1, with 32 scans using a transmittance technique with point and image modes. The data were processed (baseline, normalization, calculation of first derivate followed by smoothing with 9 point using a Savitzky-Golay algorithm) and a cluster analysis were done by Ward's algorithm and an excellent discrimination between pure and mixed culture was obtained. Our preliminary results indicate that the FT-IR microspectroscopy associated with cluster analysis can be used to discriminate between pure and mixed culture.

  7. Buffer-regulated biocorrosion of pure magnesium.

    PubMed

    Kirkland, Nicholas T; Waterman, Jay; Birbilis, Nick; Dias, George; Woodfield, Tim B F; Hartshorn, Richard M; Staiger, Mark P

    2012-02-01

    Magnesium (Mg) alloys are being actively investigated as potential load-bearing orthopaedic implant materials due to their biodegradability in vivo. With Mg biomaterials at an early stage in their development, the screening of alloy compositions for their biodegradation rate, and hence biocompatibility, is reliant on cost-effective in vitro methods. The use of a buffer to control pH during in vitro biodegradation is recognised as critically important as this seeks to mimic pH control as it occurs naturally in vivo. The two different types of in vitro buffer system available are based on either (i) zwitterionic organic compounds or (ii) carbonate buffers within a partial-CO(2) atmosphere. This study investigated the influence of the buffering system itself on the in vitro corrosion of Mg. It was found that the less realistic zwitterion-based buffer did not form the same corrosion layers as the carbonate buffer, and was potentially affecting the behaviour of the hydrated oxide layer that forms on Mg in all aqueous environments. Consequently it was recommended that Mg in vitro experiments use the more biorealistic carbonate buffering system when possible.

  8. Effect of initial orientation on the tensile properties of commercially pure titanium

    NASA Astrophysics Data System (ADS)

    Sinha, Subhasis; Ghosh, Atasi; Gurao, N. P.

    2016-05-01

    Effect of crystallographic texture on uniaxial tensile deformation of commercially pure titanium was studied using in situ as well as post-mortem electron backscatter diffraction and elastoplastic self-consistent simulations. Correlation of mechanical properties and strain hardening response with deformation micromechanisms like different modes of slip and twinning was established. Tensile specimens were machined along rolling direction in the plane perpendicular to normal and transverse direction (sample A and C, respectively) as well as along transverse direction in the plane normal to rolling direction (sample B) to obtain different initial texture from cold rolled and annealed plate of commercially pure titanium. Sample B showed higher strength but lower strain hardening rate and ductility than the orientations A and C. It showed extension twinning with lateral thickening while the other samples showed coexistence of extension and contraction twinning. Schmid factor accounted for most of the observed twinning although some contraction twinning in sample A is attributed to the effect of internal stresses. A combination of in situ tensile test in a field emission gun scanning electron microscope with electron backscatter diffraction facility and elastoplastic self-consistent simulations aid in obtaining high-fidelity Voce hardening parameters for different slip and twinning systems in commercially pure titanium. The variation in tensile properties can be explained on the basis of propensity of twinning which tends to provide strain hardening at lower strain but contributes to failure at higher strain.

  9. 1. SOUTH AND WEST ELEVATION OF ILLINOIS PURE ALUMINUM (IPA) ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. SOUTH AND WEST ELEVATION OF ILLINOIS PURE ALUMINUM (IPA) COMPANY FACTORY; SOUTH ELEVATION FACING ILLINOIS CENTRAL GULF RAILROAD TRACKS AND MAIN STREET. THE ONE-STORY BRICK BUILDING TO THE LEFT IS AN ABANDONED COMMONWEALTH EDISON COMPANY ELECTRICAL SUBSTATION. - Illinois Pure Aluminum Company, 109 Holmes Street, Lemont, Cook County, IL

  10. Physical and Spiritual Education within the Framework of Pure Life

    ERIC Educational Resources Information Center

    Bagheri Noaparast, Khosrow

    2013-01-01

    This paper aims at showing the dimensions of spirituality in childhood education by suggesting a new analysis of the concept of "pure life" used in the Qur'an. Putting spirituality in the framework of the pure life provides us with a rich framework in dealing with spirituality as the latter will be extended to all dimensions of a life. In the…

  11. Force normalization in paraplegics.

    PubMed

    Serra-Añó, P; García-Massó, X; Pellicer, M; González, L-M; López-Pascual, J; Giner-Pascual, M; Toca-Herrera, J L

    2012-06-01

    The principal aim of our study was the determination of the effectiveness of a standardized ratio, allometric scaling model and a gamma function model in normalizing the isometric torque data of spinal cord patients and healthy subjects. For this purpose we studied a sample of 21 healthy males and 23 spinal cord injury males. The experiment consisted of the measurement of the force of the upper limb movement executed by all the subjects. We also determined anthropometric variables with dual-energy x-ray absorptiometry. The experimental data were analyzed with 3 force normalization methods. Our results indicate that the most important confounding variable was the fat free mass of the dominant upper limb (r>0.36, p<0.05). With the standardization by body mass and allometric scaling model, the normalized torque was influenced by body size variables. However, the normalized torque by the gamma function model was independent of body size measures. Paraplegics were weaker (p<0.05) in extension movements when the data were normalized by the gamma function model. In summary, this study shows that the gamma function model with fat free mass of the dominant upper limb was more effective than the standardized ratio in removing the influence of body size variables. PMID:22377940

  12. Video. Pure natural orifice transluminal endoscopic surgery (NOTES) cholecystectomy.

    PubMed

    Bessler, Marc; Gumbs, Andrew A; Milone, Luca; Evanko, John C; Stevens, Peter; Fowler, Dennis

    2010-09-01

    Enthusiasm for natural orifice transluminal endoscopic surgery (NOTES) has been partly tempered by the reality that most NOTES procedures to date have been laparoscopically assisted. After safely performing transvaginal cholecystectomy in an IACUC-approved porcine model, the authors embarked on an institution review board (IRB)-approved protocol for ultimate performance of pure NOTES cholecystectomy in humans. They describe their experience performing a true NOTES transvaginal cholecystectomy after safely accomplishing three laparoscopically assisted or hybrid procedures in humans. One of the patients was a 35-year-old woman presenting with symptoms of biliary colic. Ultrasound confirmed gallstones, and her liver enzymes were normal. Pneumoperitoneum to 15 mmHg was obtained via a transvaginal trocar placed through a colpotomy made under direct vision. A double-channel endoscope then was advanced into the abdomen. To overcome the retracting limitations of currently available endoscopes, the authors used an extra-long 5-mm articulating retractor placed into the abdomen via a separate colpotomy made under direct vision using the flexible endoscope in a retroflexed position. Endoscopically placed clips were used for control of both the cystic duct and the artery. These techniques obviated the need for any transabdominally placed instruments or needles. This patient was the first to undergo a completely NOTES cholecystectomy at the authors' institution, and to their knowledge, in the United States. She was discharged on the day of surgery and at this writing has not experienced any complication after 1 month of follow-up evaluation. Performance of NOTES transvaginal cholecystectomy without aid of laparoscopic or needleoscopic instruments is feasible and safe for humans. Additional experience with this technique are required before studies comparing it with standard laparoscopy and hybrid techniques are appropriate.

  13. Activation energy of the low-load NaCl transition from nanoindentation loading curves.

    PubMed

    Kaupp, Gerd

    2014-01-01

    Access to activation energies E(a) of phase transitions is opened by unprecedented analyses of temperature dependent nanoindentation loading curves. It is based on kinks in linearized loading curves, with additional support by coincidence of kink and electrical conductivity of silicon loading curves. Physical properties of B1, B2, NaCl and further phases are discussed. The normalized low-load transition energy of NaCl (Wtrans/µN) increases with temperature and slightly decreases with load. Its semi-logarithmic plot versus T obtains activation energy E(a)/µN for calculation of the transition work for all interesting temperatures and pressures. Arrhenius-type activation energy (kJ/mol) is unavailable for indentation phase transitions. The E(a) per load normalization proves insensitive to creep-on-load, which excludes normalization to depth or volume for large temperature ranges. Such phase transition E(a)/µN is unprecedented material's property and will be of practical importance for the compatibility of composite materials under impact and further shearing interactions at elevated temperatures.

  14. Load sensing system

    DOEpatents

    Sohns, Carl W.; Nodine, Robert N.; Wallace, Steven Allen

    1999-01-01

    A load sensing system inexpensively monitors the weight and temperature of stored nuclear material for long periods of time in widely variable environments. The system can include an electrostatic load cell that encodes weight and temperature into a digital signal which is sent to a remote monitor via a coaxial cable. The same cable is used to supply the load cell with power. When multiple load cells are used, vast

  15. Strain localization during tensile Hopkinson bar testing of commercially pure titanium and Ti6Al4V titanium alloy

    NASA Astrophysics Data System (ADS)

    Moćko, Wojciech; Kruszka, Leopold; Brodecki, Adam

    2015-09-01

    The goal of the analysis was to determine the strain localization for various specimen shapes (type A and type B according to PN-EN ISO 26203-1 standard) and different loading conditions, i.e. quasi- static and dynamic. Commercially pure titanium (Grade 2) and titanium alloy Ti6Al4V (Grade 5) were selected for the tests. Tensile loadings were applied out using servo-hydraulic testing machine and tensile Hopkinson bar with pre-tension. The results were recorded using ARAMIS system cameras and fast camera Phantom V1210, respectively at quasi-static and dynamic loading conditions. Further, specimens outline was determined on the basis of video data using TEMA MOTION software. The strain distribution on the specimen surface was estimated using digital image correlation method. The larger radius present in the specimen of type B in comparison to specimen of type A, results in slight increase of the elongation for commercially pure titanium at both quasi-static and dynamic loading conditions. However this effect disappears for Ti6Al4V alloy. The increase of the elongation corresponds to the stronger necking effect. Material softening due to increase of temperature induced by plastic work was observed at dynamic loading conditions. Moreover lower elongation at fracture point was found at high strain rates for both materials.

  16. Load forecasting by ANN

    SciTech Connect

    Highley, D.D.; Hilmes, T.J. )

    1993-07-01

    This article discusses the use and training of artificial neural networks (ANNs) for load forecasting. The topics of the article include a brief overview of neural networks, interest in ANNs, training of neural networks, a case study in load forecasting, and the potential for using an artificial neural network to perform short-term load forecasting.

  17. Discharge circuits and loads

    SciTech Connect

    Sarjeant, W.J.

    1980-10-15

    This will be an overview in which some of the general properties of loads are examined: their interface with the energy storage and switching devices; general problems encountered with different types of loads; how load behavior and fault modes can impact on the design of a power conditioning system (PCS).

  18. Observation of multiband effects in the microwave complex conductivity of pure and Al-doped MgB 2 samples

    NASA Astrophysics Data System (ADS)

    Di Gennaro, E.; Lamura, G.; Palenzona, A.; Putti, M.; Andreone, A.

    2004-08-01

    There is presently a general agreement that the simple inter-metallic compound MgB 2 is a conventional, phonon mediated, superconductor, and that the anomalies in its behaviour can be consistently explained by the existence of two different gaps. We present a study of the complex conductivity as a function of temperature in pure and Al-doped MgB 2 pellets by using a dielectrically loaded resonant cavity at 19 GHz.

  19. Quantitatively Analyzing Strength Contribution vs Grain Boundary Scale Relation in Pure Titanium Subjected to Severe Plastic Deformation

    NASA Astrophysics Data System (ADS)

    Luo, Peng; Hu, Qiaodan; Wu, Xiaolin

    2016-05-01

    Electron backscatter diffraction was used to reveal high- and low-angle grain boundaries (HAGBs, with misorientation ≥15 deg, and LAGBs, <15 deg) in pure titanium (ASTM grade 2) subjected to equal channel angular pressing. Comprehensive paradigms were developed to present relations of yield strength vs HAGB grain diameter, and LAGB contribution vs LAGB linear intercept. Incorporating grain orientations (against loading axis) into the Hall-Petch relation, we quantitatively investigated the strength contributions by HAGBs and LAGBs, respectively.

  20. Normals to a Parabola

    ERIC Educational Resources Information Center

    Srinivasan, V. K.

    2013-01-01

    Given a parabola in the standard form y[superscript 2] = 4ax, corresponding to three points on the parabola, such that the normals at these three points P, Q, R concur at a point M = (h, k), the equation of the circumscribing circle through the three points P, Q, and R provides a tremendous opportunity to illustrate "The Art of Algebraic…

  1. Normal Psychosexual Development

    ERIC Educational Resources Information Center

    Rutter, Michael

    1971-01-01

    Normal sexual development is reviewed with respect to physical maturation, sexual interests, sex drive", psychosexual competence and maturity, gender role, object choice, children's concepts of sexual differences, sex role preference and standards, and psychosexual stages. Biologic, psychoanalytic and psychosocial theories are briefly considered.…

  2. Normal Birth Crossword Puzzle

    PubMed Central

    Hotelling, Barbara A.

    2006-01-01

    In this column, readers are introduced to Dawn Kersula and a crossword puzzle she designed to refresh and empower Lamaze childbirth education class participants with normal-birth information. The column's author goes on to demonstrate several ways crossword puzzles can be used in Lamaze classes. PMID:17322944

  3. 14 CFR 27.1589 - Loading information.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Loading information. 27.1589 Section 27.1589 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Operating Limitations and Information Rotorcraft...

  4. 14 CFR 27.1589 - Loading information.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Loading information. 27.1589 Section 27.1589 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Operating Limitations and Information Rotorcraft...

  5. Load Model Data Tool

    2013-04-30

    The LMDT software automates the process of the load composite model data preparation in the format supported by the major power system software vendors (GE and Siemens). Proper representation of the load composite model in power system dynamic analysis is very important. Software tools for power system simulation like GE PSLF and Siemens PSSE already include algorithms for the load composite modeling. However, these tools require that the input information on composite load to bemore » provided in custom formats. Preparation of this data is time consuming and requires multiple manual operations. The LMDT software enables to automate this process. Software is designed to generate composite load model data. It uses the default load composition data, motor information, and bus information as an input. Software processes the input information and produces load composition model. Generated model can be stored in .dyd format supported by GE PSLF package or .dyr format supported by Siemens PSSE package.« less

  6. Load Model Data Tool

    SciTech Connect

    David Chassin, Pavel Etingov

    2013-04-30

    The LMDT software automates the process of the load composite model data preparation in the format supported by the major power system software vendors (GE and Siemens). Proper representation of the load composite model in power system dynamic analysis is very important. Software tools for power system simulation like GE PSLF and Siemens PSSE already include algorithms for the load composite modeling. However, these tools require that the input information on composite load to be provided in custom formats. Preparation of this data is time consuming and requires multiple manual operations. The LMDT software enables to automate this process. Software is designed to generate composite load model data. It uses the default load composition data, motor information, and bus information as an input. Software processes the input information and produces load composition model. Generated model can be stored in .dyd format supported by GE PSLF package or .dyr format supported by Siemens PSSE package.

  7. Shunting arc plasma source for pure carbon ion beam.

    PubMed

    Koguchi, H; Sakakita, H; Kiyama, S; Shimada, T; Sato, Y; Hirano, Y

    2012-02-01

    A plasma source is developed using a coaxial shunting arc plasma gun to extract a pure carbon ion beam. The pure carbon ion beam is a new type of deposition system for diamond and other carbon materials. Our plasma device generates pure carbon plasma from solid-state carbon material without using a hydrocarbon gas such as methane gas, and the plasma does not contain any hydrogen. The ion saturation current of the discharge measured by a double probe is about 0.2 mA∕mm(2) at the peak of the pulse.

  8. Shunting arc plasma source for pure carbon ion beama)

    NASA Astrophysics Data System (ADS)

    Koguchi, H.; Sakakita, H.; Kiyama, S.; Shimada, T.; Sato, Y.; Hirano, Y.

    2012-02-01

    A plasma source is developed using a coaxial shunting arc plasma gun to extract a pure carbon ion beam. The pure carbon ion beam is a new type of deposition system for diamond and other carbon materials. Our plasma device generates pure carbon plasma from solid-state carbon material without using a hydrocarbon gas such as methane gas, and the plasma does not contain any hydrogen. The ion saturation current of the discharge measured by a double probe is about 0.2 mA/mm2 at the peak of the pulse.

  9. Pure-state informationally complete and 'really' complete measurements

    SciTech Connect

    Finkelstein, J.

    2004-11-01

    I construct a positive-operator-valued measure (POVM) which has 2d rank-1 elements and which is informationally complete for generic pure states in d dimensions, thus confirming a conjecture made by Flammia, Silberfarb, and Caves (e-print quant-ph/0404137). I show that if a rank-1 POVM is required to be informationally complete for all pure states in d dimensions, it must have at least 3d-2 elements. I also show that, in a POVM which is informationally complete for all pure states in d dimensions, for any vector there must be at least 2d-1 POVM elements which do not annihilate that vector.

  10. A novel concept for a combined-load test apparatus

    NASA Technical Reports Server (NTRS)

    Martin, Carl J.; Mcwithey, Robert R.

    1991-01-01

    An original concept for a combined-load test machine is presented in the paper. The concept employs a circular test specimen which may be rotated with respect to the biaxially applied loads. The ability to rotate the specimen and to vary the applied loads allows for limitless combinations of in-plane normal and shear loads. The loads generated in the test section reference frame are calculated from simple Mohr's circle relationships. In this paper, the concept is evaluated for isotropic, orthotropic, and discretely stiffened panels using elasticity and finite element methods. Strengths and weaknesses of the test machine concept are also discussed and evaluated.

  11. Normal-reflection image

    SciTech Connect

    Huang, L.; Fehler, Michael C.

    2003-01-01

    Common-angle wave-equation migration using the double-square-root is generally less accurate than the common-shot migration because the wavefield continuation equation for thc former involves additional approximations compared to that for the latter. We present a common-angle wave-equation migration that has the same accuracy as common-shot wave-equation migration. An image obtained from common-angle migration is a four- to five-dimensional output volume for 3D cases. We propose a normal-reflection imaging condition for common-angle migration to produce a 3D output volume for 3D migration. The image is closely related to the normal-reflection coefficients at interfaces. This imaging condition will allow amplitude-preserving migration to generate an image with clear physical meaning.

  12. Modelling of fluid-mechanical arc instability in pure-mercury HID lamps

    NASA Astrophysics Data System (ADS)

    Dreeben, Thomas D.

    2008-07-01

    A fully unsteady compressible 2D flow model is used to reproduce observed fluid-mechanical arc instability in a horizontally-running pure-mercury HID lamp. The model represents a 2D lamp cross-section normal to the arc, and assumes an infinitely long lamp. Departure from the steady condition is driven by oscillating lamp current. Sound-wave propagation and induced flows result from full coupling between the current, energy balance, ideal-gas law and conservation of mass and momentum, on two separate relevant time scales. Observed acoustically generated arc instability is reproduced with the model.

  13. Advancing Normal Birth

    PubMed Central

    Lothian, Judith

    2015-01-01

    ABSTRACT In this column, the associate editor of The Journal of Perinatal Education provides an overview of research on the benefits of promoting and protecting the normal, physiologic processes of childbirth and the risks of interfering with those processes without clear medical indication. The associate editor also describes the contents of this issue, which offer a broad range of resources, research, and inspiration for childbirth educators in their efforts to promote, support, and protect natural, safe, and healthy birth.

  14. Teaching Normal Birth Interactively

    PubMed Central

    Hotelling, Barbara A.

    2004-01-01

    In this column, the author provides examples of teaching strategies that childbirth educators may utilize to illustrate each of the six care practices supported by Lamaze International to promote normal birth: labor begins on its own, freedom of movement throughout labor, continuous labor support, no routine interventions, non-supine (e.g., upright or side-lying) positions for birth, and no separation of mother and baby with unlimited opportunity for breastfeeding. PMID:17273389

  15. Combined Load Diagram for a Wind Tunnel Strain-Gage Balance

    NASA Technical Reports Server (NTRS)

    Ulbrich, N.

    2010-01-01

    Combined Load Diagrams for Direct-Read, Force, and Moment Balances are discussed in great detail in the paper. The diagrams, if compared with a corresponding combined load plot of a balance calibration data set, may be used to visualize and interpret basic relationships between the applied balance calibration loads and the load components at the forward and aft gage of a strain-age balance. Lines of constant total force and moment are identified in the diagrams. In addition, the lines of pure force and pure moment are highlighted. Finally, lines of constant moment arm are depicted. It is also demonstrated that each quadrant of a Combined Load Diagram has specific regions where the applied total calibration force is at, between, or outside of the balance gage locations. Data from the manual calibration of a Force Balance is used to illustrate the application of a Combined Load Diagram to a realistic data set.

  16. 14 CFR 23.393 - Loads parallel to hinge line.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure...) In the absence of more rational data, the inertial loads may be assumed to be equal to KW, where—...

  17. 14 CFR 23.535 - Auxiliary float loads.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... where— L=limit load (lbs.); C5=0.0053; VS0=seaplane stalling speed (knots) with landing flaps extended... Vso in normal operations; Vso=seaplane stalling speed (knots) with landing flaps extended in...

  18. Faster and cleaner real-time pure shift NMR experiments

    NASA Astrophysics Data System (ADS)

    Mauhart, Johannes; Glanzer, Simon; Sakhaii, Peyman; Bermel, Wolfgang; Zangger, Klaus

    2015-10-01

    Real-time pure shift experiments provide highly resolved proton NMR spectra which do not require any special processing. Although being more sensitive than their pseudo 2D counterparts, their signal intensities per unit time are still far below regular NMR spectra. In addition, scalar coupling evolution during the individual data chunks produces decoupling sidebands. Here we show that faster and cleaner real-time pure shift spectra can be obtained through the implementation of two parameter alterations. Variation of the FID chunk lengths between individual transients significantly suppresses decoupling sidebands for any kind of real-time pure shift spectra and thus allows for example the analysis of minor components in compound mixtures. Shifting the excitation frequency between individual scans of real-time slice-selective pure shift spectra increases their sensitivity obtainable in unit time by allowing faster repetitions of acquisitions.

  19. [Neurolinguistic analysis of a case of pure agraphia].

    PubMed

    Petrillo, S; Poli, R; Piccirilli, M

    1990-01-01

    A patient with a pure acquired dysgraphia is reported. The pattern of the patient's performance is discussed in relation to current functional models of writing. The case may be interpreted by assuming a selective impairment to the graphemic buffer.

  20. Typical pure nonequilibrium steady states and irreversibility for quantum transport.

    PubMed

    Monnai, Takaaki; Yuasa, Kazuya

    2016-07-01

    It is known that each single typical pure state in an energy shell of a large isolated quantum system well represents a thermal equilibrium state of the system. We show that such typicality holds also for nonequilibrium steady states (NESS's). We consider a small quantum system coupled to multiple infinite reservoirs. In the long run, the total system reaches a unique NESS. We identify a large Hilbert space from which pure states of the system are to be sampled randomly and show that the typical pure states well describe the NESS. We also point out that the irreversible relaxation to the unique NESS is important to the typicality of the pure NESS's. PMID:27575115

  1. The effect of pure state structure on nonequilibrium dynamics

    NASA Astrophysics Data System (ADS)

    Newman, C. M.; Stein, D. L.

    2008-06-01

    Motivated by short-range Ising spin glasses, we review some rigorous results and their consequences for the relation between the number/nature of equilibrium pure states and nonequilibrium dynamics. Two of the consequences for spin glass dynamics following an instantaneous deep quench to a temperature with broken spin flip symmetry are: (1) almost all initial configurations lie on the boundary between the basins of attraction of multiple pure states; (2) unless there are uncountably many pure states with almost all pairs having zero overlap, there can be no equilibration to a pure state as time t \\to \\infty . We discuss the relevance of these results to the difficulty of equilibration of spin glasses. We also review some results concerning the 'nature versus nurture' problem of whether the large-t behavior of both ferromagnets and spin glasses following a deep quench is determined more by the initial configuration (nature) or by the dynamics realization (nurture).

  2. Clinical study of 222 patients with pure motor stroke.

    PubMed

    Arboix, A; Padilla, I; Massons, J; García-Eroles, L; Comes, E; Targa, C

    2001-08-01

    The objective was to assess the frequency of pure motor stroke caused by different stroke subtypes and to compare demographic, clinical, neuroimaging, and outcome data of pure motor stroke with those of patients with other lacunar stroke as well as with those of patients with non-lacunar stroke. Data from 2000 patients with acute stroke (n=1761) or transient ischaemic attack (n=239) admitted consecutively to the department of neurology of an acute care 350 bed teaching hospital were prospectively collected in the Sagrat Cor Hospital of Barcelona stroke registry over a 10 year period. For the purpose of the study 222 (12.7%) patients with pure motor stroke were selected. The other study groups included 218 (12.3%) patients with other lacunar strokes and 1321 (75%) patients with non-lacunar stroke. In relation to stroke subtype, lacunar infarcts were found in 189 (85%) patients, whereas ischaemic lacunar syndromes not due to lacunar infarcts occurred in 23 (10.4%) patients (atherothrombotic stroke in 12, cardioembolic stroke in seven, infarction of undetermined origin in three, and infarction of unusual aetiology in one) and haemorrhagic lacunar syndromes in 10 (4.5%). Patients with pure motor stroke showed a better outcome than patients with non-lacunar stroke with a significantly lower number of complications and in hospital mortality rate, shorter duration of hospital stay, and a higher number of symptom free patients at hospital discharge. After multivariate analysis, hypertension, diabetes, obesity, hyperlipidaemia, non-sudden stroke onset, internal capsule involvement, and pons topography seemed to be independent factors of pure motor stroke in patients with acute stroke. In conclusion, about one of every 10 patients with acute stroke had a pure motor stroke. Pure motor stroke was caused by a lacunar infarct in 85% of patients and by other stroke subtypes in 15%. Several clinical features are more frequent in patients with pure motor stroke than in patients

  3. Adiabatic expansion of a strongly correlated pure electron plasma

    SciTech Connect

    Dubin, D.H.E.; O'Neil, T.M.

    1986-02-17

    Adiabatic expansion is proposed as a method of increasing the degree of correlation of a magnetically confined pure electron plasma. Quantum mechanical effects and correlation effects make the physics of the expansion quite different from that for a classical ideal gas. The proposed expansion may be useful in a current experimental effort to cool a pure electron plasma to the liquid and solid (crystalline) states.

  4. Adiabatic expansion of a strongly correlated pure electron plasma

    NASA Astrophysics Data System (ADS)

    Dubin, D. H. E.; Oneil, T. M.

    1986-02-01

    Adiabatic expansion is proposed as a method of increasing the degree of correlation of a magnetically confined pure electron plasma. Quantum mechanical effects and correlation effects make the physics of the expansion quite different from that for a classical ideal gas. The proposed expansion may be useful in a current experimental effort to cool a pure electron plasma to the liquid and solid (crystalline) states.

  5. Automated pure-tone threshold estimations from extrapolated distortion product otoacoustic emission (DPOAE) input/output functions.

    PubMed

    Schmuziger, Nicolas; Patscheke, Jochen; Probst, Rudolf

    2006-04-01

    A promising approach to the prediction of pure-tone thresholds through the estimation of DPOAE thresholds by input/output functions was recently published by Boege and Janssen [J. Acoust. Soc. Am. 111, 1810-1818 (2002)]. On the basis of their results, a device that enables automated measurements of these thresholds was recently developed. The purpose of the current study was to evaluate the reliability of this instrument for the objective assessment of hearing loss in 101 ears with either normal hearing or with cochlear hearing loss of up to 50 dB HL. The median difference between pure-tone hearing and DPOAE thresholds was approximately 2 dB. For individual subjects, however, DPOAE thresholds differed from pure-tone thresholds by up to 40 dB. We find, therefore, that the clinical benefits of this method are probably limited.

  6. Hybrids, pure cultures, and pure lines: from nineteenth-century biology to twentieth-century genetics.

    PubMed

    Müller-Wille, Staffan

    2007-12-01

    Prompted by recent recognitions of the omnipresence of horizontal gene transfer among microbial species and the associated emphasis on exchange, rather than isolation, as the driving force of evolution, this essay will reflect on hybridization as one of the central concerns of nineteenth-century biology. I will argue that an emphasis on horizontal exchange was already endorsed by 'biology' when it came into being around 1800 and was brought to full fruition with the emergence of genetics in 1900. The true revolution in nineteenth-century life sciences, I maintain, consisted in a fundamental shift in ontology, which eroded the boundaries between individual and species, and allowed biologists to move up and down the scale of organic complexity. Life became a property extending both 'downwards', to the parts that organisms were composed of, as well as 'upwards', to the collective entities constituted by the relations of exchange and interaction that organisms engage in to reproduce. This mode of thinking was crystallized by Gregor Mendel and consolidated in the late nineteenth-century conjunction of biochemistry, microbiology and breeding in agro-industrial settings. This conjunction and its implications are especially exemplified by Wilhelm Johannsen's and Martinus Beijerinck's work on pure lines and cultures. An understanding of the subsequent constraints imposed by the evolutionary synthesis of the twentieth century on models of genetic systems may require us to rethink the history of biology and displace Darwin's theory of natural selection from that history's centre. PMID:18053934

  7. Phalange Tactile Load Cell

    NASA Technical Reports Server (NTRS)

    Ihrke, Chris A. (Inventor); Diftler, Myron A. (Inventor); Linn, Douglas Martin (Inventor); Platt, Robert (Inventor); Griffith, Bryan Kristian (Inventor)

    2010-01-01

    A tactile load cell that has particular application for measuring the load on a phalange in a dexterous robot system. The load cell includes a flexible strain element having first and second end portions that can be used to mount the load cell to the phalange and a center portion that can be used to mount a suitable contact surface to the load cell. The strain element also includes a first S-shaped member including at least three sections connected to the first end portion and the center portion and a second S-shaped member including at least three sections coupled to the second end portion and the center portion. The load cell also includes eight strain gauge pairs where each strain gauge pair is mounted to opposing surfaces of one of the sections of the S-shaped members where the strain gauge pairs provide strain measurements in six-degrees of freedom.

  8. 14 CFR 23.726 - Ground load dynamic tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Ground load dynamic tests. 23.726 Section 23.726 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Landing Gear § 23.726 Ground load...

  9. 14 CFR 23.535 - Auxiliary float loads.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... are as follows: EC28SE91.011 where— P=mass density of water (slugs/ft.3) V=volume of float (ft.3); CX... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23... paragraphs (b) through (e) of this section, the prescribed water loads may be distributed over the...

  10. 14 CFR 23.535 - Auxiliary float loads.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... are as follows: EC28SE91.011 where— P=mass density of water (slugs/ft.3) V=volume of float (ft.3); CX... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Water Loads § 23... paragraphs (b) through (e) of this section, the prescribed water loads may be distributed over the...

  11. 14 CFR 23.371 - Gyroscopic and aerodynamic loads.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... prescribed in § 23.351 and § 23.423; or (2) All possible combinations of the following— (i) A yaw velocity of 2.5 radians per second; (ii) A pitch velocity of 1.0 radian per second; (iii) A normal load factor... be designed to withstand the load factors expected during combined maximum yaw and pitch...

  12. 14 CFR 23.371 - Gyroscopic and aerodynamic loads.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... prescribed in § 23.351 and § 23.423; or (2) All possible combinations of the following— (i) A yaw velocity of 2.5 radians per second; (ii) A pitch velocity of 1.0 radian per second; (iii) A normal load factor... be designed to withstand the load factors expected during combined maximum yaw and pitch...

  13. 14 CFR 23.371 - Gyroscopic and aerodynamic loads.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... prescribed in § 23.351 and § 23.423; or (2) All possible combinations of the following— (i) A yaw velocity of 2.5 radians per second; (ii) A pitch velocity of 1.0 radian per second; (iii) A normal load factor... be designed to withstand the load factors expected during combined maximum yaw and pitch...

  14. 14 CFR 23.371 - Gyroscopic and aerodynamic loads.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... prescribed in § 23.351 and § 23.423; or (2) All possible combinations of the following— (i) A yaw velocity of 2.5 radians per second; (ii) A pitch velocity of 1.0 radian per second; (iii) A normal load factor... be designed to withstand the load factors expected during combined maximum yaw and pitch...

  15. 14 CFR 23.371 - Gyroscopic and aerodynamic loads.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... prescribed in § 23.351 and § 23.423; or (2) All possible combinations of the following— (i) A yaw velocity of 2.5 radians per second; (ii) A pitch velocity of 1.0 radian per second; (iii) A normal load factor... be designed to withstand the load factors expected during combined maximum yaw and pitch...

  16. 14 CFR 23.341 - Gust loads factors.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... load case. W/S=Wing loading (p.s.f.); C=Mean geometric chord (ft.); g=Acceleration due to gravity (ft./sec.2) V=Airplane equivalent speed (knots); and a=Slope of the airplane normal force coefficient...

  17. 14 CFR 23.341 - Gust loads factors.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... load case. W/S=Wing loading (p.s.f.); C=Mean geometric chord (ft.); g=Acceleration due to gravity (ft./sec.2) V=Airplane equivalent speed (knots); and a=Slope of the airplane normal force coefficient...

  18. 14 CFR 23.341 - Gust loads factors.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... load case. W/S=Wing loading (p.s.f.); C=Mean geometric chord (ft.); g=Acceleration due to gravity (ft./sec.2) V=Airplane equivalent speed (knots); and a=Slope of the airplane normal force coefficient...

  19. Structural evaluation of the 2736Z Building for seismic loads

    SciTech Connect

    Giller, R.A.

    1994-09-23

    The 2736Z building structure is evaluated for high-hazard loads. The 2736Z building is analyzed herein for normal and seismic loads and is found to successfully meet the guidelines of UCRL-15910 along with the related codes requirements.

  20. DISJUNCTIVE NORMAL SHAPE MODELS

    PubMed Central

    Ramesh, Nisha; Mesadi, Fitsum; Cetin, Mujdat; Tasdizen, Tolga

    2016-01-01

    A novel implicit parametric shape model is proposed for segmentation and analysis of medical images. Functions representing the shape of an object can be approximated as a union of N polytopes. Each polytope is obtained by the intersection of M half-spaces. The shape function can be approximated as a disjunction of conjunctions, using the disjunctive normal form. The shape model is initialized using seed points defined by the user. We define a cost function based on the Chan-Vese energy functional. The model is differentiable, hence, gradient based optimization algorithms are used to find the model parameters. PMID:27403233

  1. Effect of load introduction on graphite epoxy compression specimens

    NASA Technical Reports Server (NTRS)

    Reiss, R.; Yao, T. M.

    1981-01-01

    Compression testing of modern composite materials is affected by the manner in which the compressive load is introduced. Two such effects are investigated: (1) the constrained edge effect which prevents transverse expansion and is common to all compression testing in which the specimen is gripped in the fixture; and (2) nonuniform gripping which induces bending into the specimen. An analytical model capable of quantifying these foregoing effects was developed which is based upon the principle of minimum complementary energy. For pure compression, the stresses are approximated by Fourier series. For pure bending, the stresses are approximated by Legendre polynomials.

  2. Biomechanical load analysis of cantilevered implant systems.

    PubMed

    Osier, J F

    1991-01-01

    Historically, dental implants have been placed in areas where quality bone exists. The maxillary sinus areas and mandibular canal proximities have been avoided. From these placements, various cantilevered prosthetic applications have emerged. This analysis uses static engineering principles to define the loads (i.e., forces) placed upon the implants. These principles make use of Newton's first and third laws of mechanics by summing the forces and moments to zero. These summations then generate mathematical equations and their algebraic solutions. Three implant systems are analyzed. The first is a two-implant system. The second is a three-implant cross-arch stabilized system usually found in mandibular replacements of lower full dentures. The third is a five-implant system which is identical to the three-implant cantilevered system but which uses implants in the first molar area, thereby negating the cantilevered load magnification of the three-implant design. These analyses demonstrate that, in a cantilevered application, the implant closest to the point of load application (usually the most posterior implant) takes the largest compressive load. Implants opposite the load application (generally the anterior implant) are in tension. These loads on the implants are normally magnified over the biting force and can easily reach 2 1/2 to five times the biting load.

  3. Citraturic response to oral citric acid load

    NASA Technical Reports Server (NTRS)

    Sakhaee, K.; Alpern, R.; Poindexter, J.; Pak, C. Y.

    1992-01-01

    It is possible that some orally administered citrate may appear in urine by escaping oxidation in vivo. To determine whether this mechanism contributes to the citraturic response to potassium citrate, we measured serum and urinary citrate for 4 hours after a single oral load of citric acid (40 mEq.) in 6 normal subjects. Since citric acid does not alter acid-base balance, the effect of absorbed citrate could be isolated from that of alkali load. Serum citrate concentration increased significantly (p less than 0.05) 30 minutes after a single oral dose of citric acid and remained significantly elevated for 3 hours after citric acid load. Commensurate with this change, urinary citrate excretion peaked at 2 hours and gradually decreased during the next 2 hours after citric acid load. In contrast, serum and urinary citrate remained unaltered following the control load (no drug). Differences of the citratemic and citraturic effects between phases were significant (p less than 0.05) at 2 and 3 hours. Urinary pH, carbon dioxide pressure, bicarbonate, total carbon dioxide and ammonium did not change at any time after citric acid load, and did not differ between the 2 phases. No significant difference was noted in serum electrolytes, arterialized venous pH and carbon dioxide pressure at any time after citric acid load and between the 2 phases. Thus, the citraturic and citratemic effects of oral citric acid are largely accountable by provision of absorbed citrate, which has escaped in vivo degradation.

  4. Sensate Scaffolds Can Reliably Detect Joint Loading

    PubMed Central

    Bliss, C. L.; Szivek, J. A.; Tellis, B. C.; Margolis, D. S.; Schnepp, A. B.; Ruth, J. T.

    2008-01-01

    Treatment of cartilage defects is essential to the prevention of osteoarthritis. Scaffold-based cartilage tissue engineering shows promise as a viable technique to treat focal defects. Added functionality can be achieved by incorporating strain gauges into scaffolds, thereby providing a real-time diagnostic measurement of joint loading. Strain-gauged scaffolds were placed into the medial femoral condyles of 14 adult canine knees and benchtop tested. Loads between 75 and 130 N were applied to the stifle joints at 30°, 50°, and 70° of flexion. Strain-gauged scaffolds were able to reliably assess joint loading at all applied flexion angles and loads. Pressure sensitive films were used to determine joint surface pressures during loading and to assess the effect of scaffold placement on joint pressures. A comparison of peak pressures in control knees and joints with implanted scaffolds, as well as a comparison of pressures before and after scaffold placement, showed that strain-gauged scaffold implantation did not significantly alter joint pressures. Future studies could possibly use strain-gauged scaffolds to clinically establish normal joint loads and to determine loads that are damaging to both healthy and tissue-engineered cartilage. Strain-gauged scaffolds may significantly aid the development of a functional engineered cartilage tissue substitute as well as provide insight into the native environment of cartilage. PMID:16941586

  5. Platelet lysate and chondroitin sulfate loaded contact lenses to heal corneal lesions.

    PubMed

    Sandri, Giuseppina; Bonferoni, Maria Cristina; Rossi, Silvia; Delfino, Alessio; Riva, Federica; Icaro Cornaglia, Antonia; Marrubini, Giorgio; Musitelli, Giorgio; Del Fante, Claudia; Perotti, Cesare; Caramella, Carla; Ferrari, Franca

    2016-07-25

    Hemoderivative tear substitutes contain various ephiteliotrophic factors, such as growth factors (GF), involved in ocular surface homeostasis without immunogenic properties. The aim of the present work was the loading of platelet lysate into contact lenses to improve the precorneal permanence of platelet lysate growth factors on the ocular surface to enhance the treatment of corneal lesions. To this purpose, chondroitin sulfate, a sulfated glycosaminoglycan, which is normally present in the extracellular matrix, was associated with platelet lysate. In fact, chondroitin sulfate is capable of electrostatic interaction with positively charged growth factors, in particular, with bFGF, IGF, VEGF, PDGF and TGF-β, resulting in their stabilization and reduced degradation in solution. In the present work, various types of commercially available contact lenses have been loaded with chondroitin sulfate or chondroitin sulfate in association with platelet lysate to achieve a release of growth factors directly onto the corneal surface lesions. One type of contact lenses (PureVision(®)) showed in vitro good proliferation properties towards corneal cells and were able to enhance cut closure in cornea constructs.

  6. Platelet lysate and chondroitin sulfate loaded contact lenses to heal corneal lesions.

    PubMed

    Sandri, Giuseppina; Bonferoni, Maria Cristina; Rossi, Silvia; Delfino, Alessio; Riva, Federica; Icaro Cornaglia, Antonia; Marrubini, Giorgio; Musitelli, Giorgio; Del Fante, Claudia; Perotti, Cesare; Caramella, Carla; Ferrari, Franca

    2016-07-25

    Hemoderivative tear substitutes contain various ephiteliotrophic factors, such as growth factors (GF), involved in ocular surface homeostasis without immunogenic properties. The aim of the present work was the loading of platelet lysate into contact lenses to improve the precorneal permanence of platelet lysate growth factors on the ocular surface to enhance the treatment of corneal lesions. To this purpose, chondroitin sulfate, a sulfated glycosaminoglycan, which is normally present in the extracellular matrix, was associated with platelet lysate. In fact, chondroitin sulfate is capable of electrostatic interaction with positively charged growth factors, in particular, with bFGF, IGF, VEGF, PDGF and TGF-β, resulting in their stabilization and reduced degradation in solution. In the present work, various types of commercially available contact lenses have been loaded with chondroitin sulfate or chondroitin sulfate in association with platelet lysate to achieve a release of growth factors directly onto the corneal surface lesions. One type of contact lenses (PureVision(®)) showed in vitro good proliferation properties towards corneal cells and were able to enhance cut closure in cornea constructs. PMID:27234702

  7. Failure mechanisms of laminated carbon-carbon composites; 2: Under shear loads

    SciTech Connect

    Anand, K.; Gupta, V.; Dartford, D. . Thayer School of Engineering)

    1994-03-01

    Failure mechanisms under both interlaminar and in-plane shear loading are determined for two-dimensional carbon-carbon composites by using a direct shear set-up. This set-up is applicable for both types of shear loading as manufactured laminate thickness can be tested without the need to make long samples by gluing different pieces together. A detailed finite element analysis, which considers the microstructure of the composite shows that for woven laminates, the initial crimp angle morphology does not allow the composite to deform in a state of simple shear. In fact, normal tensile and compressive stresses of almost twice the magnitude of the peak shear stress are produced in the vicinity of the crimped bundles. Consistent with these predictions, the authors observed the shear fault following the crimp boundaries in 0[degree]/90[degree] and quasi-isotropic laminates. Therefore, experimental techniques which can secure a state of pure shear stress in aligned, unkinked, uniaxial fiber composites cannot do so in woven laminated composites.

  8. Load sensing system

    DOEpatents

    Sohns, C.W.; Nodine, R.N.; Wallace, S.A.

    1999-05-04

    A load sensing system inexpensively monitors the weight and temperature of stored nuclear material for long periods of time in widely variable environments. The system can include an electrostatic load cell that encodes weight and temperature into a digital signal which is sent to a remote monitor via a coaxial cable. The same cable is used to supply the load cell with power. When multiple load cells are used, vast inventories of stored nuclear material can be continuously monitored and inventoried of minimal cost. 4 figs.

  9. Load regulating expansion fixture

    DOEpatents

    Wagner, L.M.; Strum, M.J.

    1998-12-15

    A free standing self contained device for bonding ultra thin metallic films, such as 0.001 inch beryllium foils is disclosed. The device will regulate to a predetermined load for solid state bonding when heated to a bonding temperature. The device includes a load regulating feature, whereby the expansion stresses generated for bonding are regulated and self adjusting. The load regulator comprises a pair of friction isolators with a plurality of annealed copper members located therebetween. The device, with the load regulator, will adjust to and maintain a stress level needed to successfully and economically complete a leak tight bond without damaging thin foils or other delicate components. 1 fig.

  10. Load regulating expansion fixture

    DOEpatents

    Wagner, Lawrence M.; Strum, Michael J.

    1998-01-01

    A free standing self contained device for bonding ultra thin metallic films, such as 0.001 inch beryllium foils. The device will regulate to a predetermined load for solid state bonding when heated to a bonding temperature. The device includes a load regulating feature, whereby the expansion stresses generated for bonding are regulated and self adjusting. The load regulator comprises a pair of friction isolators with a plurality of annealed copper members located therebetween. The device, with the load regulator, will adjust to and maintain a stress level needed to successfully and economically complete a leak tight bond without damaging thin foils or other delicate components.

  11. [Normal and disordered sleep].

    PubMed

    Arnulf, I

    2007-07-01

    Normal sleep is a complex and reversible state of brain functioning, including reduced inputs and outputs, blunted reflexes, and metabolic and cognitive changes. Evidence supports a role for sleep in the consolidation of an array of learning and memory tasks. Sleep deprivation and fragmentation result in executive dysfunction, increased appetite/weight and cellular stress. Sleep is a vital, complex but plastic function that can be modulated depending on individual heritage and motivation. The major role of sleep in attention and memory raises about concern the reduction in sleep duration recently pointed in teenagers and young adults. Sleep disorders are numerous and various. Their mechanism is not always identified, but may result from a central dysfunction in sleep-wake (e.g. narcolepsy) or circadian (e.g. advanced sleep phase syndrome) systems, from the sleep-related loss of compensation of reflexes normally effective during wakefulness (breathing is the most vulnerable function during sleep), or from other diseases preventing sleep (e.g. psychiatric insomnia, restless legs syndrome). PMID:17652992

  12. Design and analysis of a novel mechanical loading machine for dynamic in vivo axial loading

    NASA Astrophysics Data System (ADS)

    Macione, James; Nesbitt, Sterling; Pandit, Vaibhav; Kotha, Shiva

    2012-02-01

    This paper describes the construction of a loading machine for performing in vivo, dynamic mechanical loading of the rodent forearm. The loading machine utilizes a unique type of electromagnetic actuator with no mechanically resistive components (servotube), allowing highly accurate loads to be created. A regression analysis of the force created by the actuator with respect to the input voltage demonstrates high linear correlation (R2 = 1). When the linear correlation is used to create dynamic loading waveforms in the frequency (0.5-10 Hz) and load (1-50 N) range used for in vivo loading, less than 1% normalized root mean square error (NRMSE) is computed. Larger NRMSE is found at increased frequencies, with 5%-8% occurring at 40 Hz, and reasons are discussed. Amplifiers (strain gauge, linear voltage displacement transducer (LVDT), and load cell) are constructed, calibrated, and integrated, to allow well-resolved dynamic measurements to be recorded at each program cycle. Each of the amplifiers uses an active filter with cutoff frequency at the maximum in vivo loading frequencies (50 Hz) so that electronic noise generated by the servo drive and actuator are reduced. The LVDT and load cell amplifiers allow evaluation of stress-strain relationships to determine if in vivo bone damage is occurring. The strain gauge amplifier allows dynamic force to strain calibrations to occur for animals of different sex, age, and strain. Unique features are integrated into the loading system, including a weightless mode, which allows the limbs of anesthetized animals to be quickly positioned and removed. Although the device is constructed for in vivo axial bone loading, it can be used within constraints, as a general measurement instrument in a laboratory setting.

  13. On compensatory strategies and computational models: the case of pure alexia.

    PubMed

    Shallice, Tim

    2014-01-01

    The article is concerned with inferences from the behaviour of neurological patients to models of normal function. It takes the letter-by-letter reading strategy common in pure alexic patients as an example of the methodological problems involved in making such inferences that compensatory strategies produce. The evidence is discussed on the possible use of three ways the letter-by-letter reading process might operate: "reversed spelling"; the use of the phonological input buffer as a temporary holding store during word building; and the use of serial input to the visual word-form system entirely within the visual-orthographic domain such as in the model of Plaut [1999. A connectionist approach to word reading and acquired dyslexia: Extension to sequential processing. Cognitive Science, 23, 543-568]. The compensatory strategy used by, at least, one pure alexic patient does not fit with the third of these possibilities. On the more general question, it is argued that even if compensatory strategies are being used, the behaviour of neurological patients can be useful for the development and assessment of first-generation information-processing models of normal function, but they are not likely to be useful for the development and assessment of second-generation computational models.

  14. Normally Expected Aberrations in the 8-hour Dynamic EKG

    NASA Technical Reports Server (NTRS)

    Fleck, R. L.; Arnoldi, L. B.; Townsend, J. C.; Tonesk, X.

    1970-01-01

    The establishment of norms for interpreting long term dynamic electrocardiograms is attempted by correlating a completely disease symptom and cardiac risk factor free sample with a non-pure sample in the direction of normality on various variables. Out of a population of 362 subjects exposed to dynamic electrocardiogram testing, a discrimination between normals and abnormals in terms of traditional risk factors was observed. The two groups differed significantly on the following variables: cholesterol, smoking, systolic blood pressure, white blood count, fasting blood sugar, uric acid, resting EKG, year of birth, and coronary insufficiency.

  15. Microbial load monitor

    NASA Technical Reports Server (NTRS)

    Caplin, R. S.; Royer, E. R.

    1977-01-01

    Design analysis of a microbial load monitor system flight engineering model was presented. Checkout of the card taper and media pump system was fabricated as well as the final two incubating reading heads, the sample receiving and card loading device assembly, related sterility testing, and software. Progress in these areas was summarized.

  16. Combined Load Test Fixture

    NASA Technical Reports Server (NTRS)

    Baker, Donald J.

    2010-01-01

    A test fixture has been developed at NASA Langley Research Center that has the capability of applying compression load and shear load simultaneously to a test specimen. The test specimen size is 24-inches by 28-inches. This report describes the test specimen design, test specimen preparation, fixture assembly in the test machine, and a test operation plan.

  17. CRITICAL LOADS METHODS

    EPA Science Inventory

    I summarize the results of an interagency project that 1) defines a generic approach to quantifying and reporting critical loads, and 2) exercises that generic approach by examining a data rich system -- the critical loads of sulfur deposition and it's effect on the chronic acidi...

  18. Load Induced Blindness

    ERIC Educational Resources Information Center

    Macdonald, James S. P.; Lavie, Nilli

    2008-01-01

    Although the perceptual load theory of attention has stimulated a great deal of research, evidence for the role of perceptual load in determining perception has typically relied on indirect measures that infer perception from distractor effects on reaction times or neural activity (see N. Lavie, 2005, for a review). Here we varied the level of…

  19. Pornography, normalization, and empowerment.

    PubMed

    Weinberg, Martin S; Williams, Colin J; Kleiner, Sibyl; Irizarry, Yasmiyn

    2010-12-01

    Opponents and proponents of erotic representations (referred to hereafter as "pornography") have described the effects of pornography from their perspective. Little, however, has been done in the way of research to investigate these claims from the consumer's point of view. This especially has been so regarding the positive impact of such consumption on a person's sex life. Using a study group of 245 college students, we examined this question in a framework of scripting theory. We wanted to see whether viewing pornography appeared to expand sexual horizons through normalization and facilitate a willingness to explore new sexual behaviors and sexual relationships through empowerment. The data supported this viewpoint and further showed the effects to be mediated by gender and sexual preference identity. They suggested, however, that established scripts were extended rather than abandoned. We conclude with connections between our findings and the widespread viewing of pornography in contemporary society. PMID:20127507

  20. Normal Untreated Jurkat Cells

    NASA Technical Reports Server (NTRS)

    2004-01-01

    Biomedical research offers hope for a variety of medical problems, from diabetes to the replacement of damaged bone and tissues. Bioreactors, which are used to grow cells and tissue cultures, play a major role in such research and production efforts. The objective of the research was to define a way to differentiate between effects due to microgravity and those due to possible stress from non-optimal spaceflight conditions. These Jurkat cells, a human acute T-cell leukemia was obtained to evaluate three types of potential experimental stressors: a) Temperature elevation; b) Serum starvation; and c) Centrifugal force. The data from previous spaceflight experiments showed that actin filaments and cell shape are significantly different for the control. These normal cells serve as the baseline for future spaceflight experiments.

  1. Accurate Thermal Stresses for Beams: Normal Stress

    NASA Technical Reports Server (NTRS)

    Johnson, Theodore F.; Pilkey, Walter D.

    2003-01-01

    Formulations for a general theory of thermoelasticity to generate accurate thermal stresses for structural members of aeronautical vehicles were developed in 1954 by Boley. The formulation also provides three normal stresses and a shear stress along the entire length of the beam. The Poisson effect of the lateral and transverse normal stresses on a thermally loaded beam is taken into account in this theory by employing an Airy stress function. The Airy stress function enables the reduction of the three-dimensional thermal stress problem to a two-dimensional one. Numerical results from the general theory of thermoelasticity are compared to those obtained from strength of materials. It is concluded that the theory of thermoelasticity for prismatic beams proposed in this paper can be used instead of strength of materials when precise stress results are desired.

  2. Accurate Thermal Stresses for Beams: Normal Stress

    NASA Technical Reports Server (NTRS)

    Johnson, Theodore F.; Pilkey, Walter D.

    2002-01-01

    Formulations for a general theory of thermoelasticity to generate accurate thermal stresses for structural members of aeronautical vehicles were developed in 1954 by Boley. The formulation also provides three normal stresses and a shear stress along the entire length of the beam. The Poisson effect of the lateral and transverse normal stresses on a thermally loaded beam is taken into account in this theory by employing an Airy stress function. The Airy stress function enables the reduction of the three-dimensional thermal stress problem to a two-dimensional one. Numerical results from the general theory of thermoelasticity are compared to those obtained from strength of materials. It is concluded that the theory of thermoelasticity for prismatic beams proposed in this paper can be used instead of strength of materials when precise stress results are desired.

  3. Transportation and handling loads

    NASA Technical Reports Server (NTRS)

    Ostrem, F. E.

    1971-01-01

    Criteria and recommended practices are presented for the prediction and verification of transportation and handling loads for the space vehicle structure and for monitoring these loads during transportation and handling of the vehicle or major vehicle segments. Elements of the transportation and handling systems, and the forcing functions and associated loads are described. The forcing functions for common carriers and typical handling devices are assessed, and emphasis is given to the assessment of loads at the points where the space vehicle is supported during transportation and handling. Factors which must be considered when predicting the loads include the transportation and handling medium; type of handling fixture; transport vehicle speed; types of terrain; weather (changes in pressure of temperature, wind, etc.); and dynamics of the transportation modes or handling devices (acceleration, deceleration, and rotations of the transporter or handling device).

  4. Critical current degradation behaviour of GdBCO CC tapes in pure torsion and combined tension-torsion modes

    NASA Astrophysics Data System (ADS)

    Gorospe, Alking; Bautista, Zhierwinjay; Shin, Hyung-Seop

    2016-10-01

    Coated conductor (CC) tapes utilized in high-current-density superconducting cables are commonly subjected to different loading modes, primarily torsion and tension especially in the case of twisted stacked-tape cable. Torsion load can occur due to twisting along the length or when winding the CC tapes around a former, while tension load can occur due to pre-tension when coiled and as a hoop stress when the coil is energized. In this study, electromechanical properties of single CC tapes under torsion load were investigated using a new test apparatus. The results could provide basic information for cable designers to fully characterize stacked cables. Copper-electroplated and brass-laminated CC tapes fabricated with different deposition techniques were subjected to pure torsion and combined tension-torsion loading. The critical current, I c degradation behaviours of CC tapes under torsional deformation were examined. Also, the effect of further external lamination on the I c degradation behaviour of the CC tapes under such loading conditions was investigated. In the case of the combined tension-torsion test, short samples were subjected to twist pitches of 200 mm and 100 mm. Critical parameters including reversible axial stress and strain in such twist pitch conditions were also investigated.

  5. X-linked recessive type of pure spastic paraplegia in a large pedigree: absence of detectable linkage with Xg.

    PubMed Central

    Zatz, M; Penha-Serrano, C; Otto, P A

    1976-01-01

    A family with 24 males affected by an X-linked type of spastic paraplegia is reported. Twelve affected members were personally examined showing the pure form of the disease. Half of the affected males had many descendants, all normal. Linkage studies strongly suggest that this X-linked form of spastic paraplegia and Xg loci are not at a measurable distance on the X chromosome. PMID:1084423

  6. Running with a load increases leg stiffness.

    PubMed

    Silder, Amy; Besier, Thor; Delp, Scott L

    2015-04-13

    Spring-mass models have been used to characterize running mechanics and leg stiffness in a variety of conditions, yet it remains unknown how running while carrying a load affects running mechanics and leg stiffness. The purpose of this study was to test the hypothesis that running with a load increases leg stiffness. Twenty-seven subjects ran at a constant speed on a force-measuring treadmill while carrying no load, and while wearing weight vests loaded with 10%, 20%, and 30% of body weight. We measured lower extremity motion and created a scaled musculoskeletal model of each subject, which we used to estimate lower extremity joint angles and leg length. We estimated dimensionless leg stiffness as the ratio of the peak vertical ground reaction force (normalized to body weight) and the change in stance phase leg length (normalized to leg length at initial foot contact). Leg length was calculated as the distance from the center of the pelvis to the center-of-pressure under the foot. We found that dimensionless leg stiffness increased when running with load (p=0.001); this resulted from an increase in the peak vertical ground reaction force (p<0.001) and a smaller change in stance phase leg length (p=0.025). When running with load, subjects had longer ground contact times (p<0.020), greater hip (p<0.001) and knee flexion (p=0.048) at the time of initial foot contact, and greater peak stance phase hip, knee, and ankle flexion (p<0.05). Our results reveal that subjects run in a more crouched posture and with higher leg stiffness to accommodate an added load.

  7. Running with a load increases leg stiffness.

    PubMed

    Silder, Amy; Besier, Thor; Delp, Scott L

    2015-04-13

    Spring-mass models have been used to characterize running mechanics and leg stiffness in a variety of conditions, yet it remains unknown how running while carrying a load affects running mechanics and leg stiffness. The purpose of this study was to test the hypothesis that running with a load increases leg stiffness. Twenty-seven subjects ran at a constant speed on a force-measuring treadmill while carrying no load, and while wearing weight vests loaded with 10%, 20%, and 30% of body weight. We measured lower extremity motion and created a scaled musculoskeletal model of each subject, which we used to estimate lower extremity joint angles and leg length. We estimated dimensionless leg stiffness as the ratio of the peak vertical ground reaction force (normalized to body weight) and the change in stance phase leg length (normalized to leg length at initial foot contact). Leg length was calculated as the distance from the center of the pelvis to the center-of-pressure under the foot. We found that dimensionless leg stiffness increased when running with load (p=0.001); this resulted from an increase in the peak vertical ground reaction force (p<0.001) and a smaller change in stance phase leg length (p=0.025). When running with load, subjects had longer ground contact times (p<0.020), greater hip (p<0.001) and knee flexion (p=0.048) at the time of initial foot contact, and greater peak stance phase hip, knee, and ankle flexion (p<0.05). Our results reveal that subjects run in a more crouched posture and with higher leg stiffness to accommodate an added load. PMID:25728581

  8. 46 CFR 112.20-15 - Transfer of emergency loads.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Transfer of emergency loads. 112.20-15 Section 112.20-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING... seconds after failure of the normal source of power. (b) When the potential from the normal source...

  9. The neuroanatomy of pure apraxia of speech in stroke

    PubMed Central

    Graff-Radford, Jonathan; Jones, David T.; Strand, Edythe A.; Rabinstein, Alejandro A.; Duffy, Joseph R.; Josephs, Keith A.

    2014-01-01

    The left insula or Broca’s area have been proposed as the neuroanatomical correlate for apraxia of speech (AOS) based on studies of patients with both AOS and aphasia due to stroke. Studies of neurodegenerative AOS suggest the premotor area and the supplementary motor areas as the anatomical correlates. The study objective was to determine the common infarction area in patients with pure AOS due to stroke. Patients with AOS and no or equivocal aphasia due to ischemic stroke were identified through a pre-existing database. Seven subjects were identified. Five had pure AOS, and two had equivocal aphasia. MRI lesion analysis revealed maximal overlap spanning the left premotor and motor cortices. While both neurodegenerative AOS and stroke induced pure AOS involve the premotor cortex, further studies are needed to establish whether stroke-induced AOS and neurodegenerative AOS share a common anatomic substrate. PMID:24556336

  10. Excitation of coherent propagating spin waves by pure spin currents

    PubMed Central

    Demidov, Vladislav E.; Urazhdin, Sergei; Liu, Ronghua; Divinskiy, Boris; Telegin, Andrey; Demokritov, Sergej O.

    2016-01-01

    Utilization of pure spin currents not accompanied by the flow of electrical charge provides unprecedented opportunities for the emerging technologies based on the electron's spin degree of freedom, such as spintronics and magnonics. It was recently shown that pure spin currents can be used to excite coherent magnetization dynamics in magnetic nanostructures. However, because of the intrinsic nonlinear self-localization effects, magnetic auto-oscillations in the demonstrated devices were spatially confined, preventing their applications as sources of propagating spin waves in magnonic circuits using these waves as signal carriers. Here, we experimentally demonstrate efficient excitation and directional propagation of coherent spin waves generated by pure spin current. We show that this can be achieved by using the nonlocal spin injection mechanism, which enables flexible design of magnetic nanosystems and allows one to efficiently control their dynamic characteristics. PMID:26818232

  11. The neuroanatomy of pure apraxia of speech in stroke.

    PubMed

    Graff-Radford, Jonathan; Jones, David T; Strand, Edythe A; Rabinstein, Alejandro A; Duffy, Joseph R; Josephs, Keith A

    2014-02-01

    The left insula or Broca's area have been proposed as the neuroanatomical correlate for apraxia of speech (AOS) based on studies of patients with both AOS and aphasia due to stroke. Studies of neurodegenerative AOS suggest the premotor area and the supplementary motor areas as the anatomical correlates. The study objective was to determine the common infarction area in patients with pure AOS due to stroke. Patients with AOS and no or equivocal aphasia due to ischemic stroke were identified through a pre-existing database. Seven subjects were identified. Five had pure AOS, and two had equivocal aphasia. MRI lesion analysis revealed maximal overlap spanning the left premotor and motor cortices. While both neurodegenerative AOS and stroke induced pure AOS involve the premotor cortex, further studies are needed to establish whether stroke-induced AOS and neurodegenerative AOS share a common anatomic substrate. PMID:24556336

  12. Fast word reading in pure alexia: "fast, yet serial".

    PubMed

    Bormann, Tobias; Wolfer, Sascha; Hachmann, Wibke; Neubauer, Claudia; Konieczny, Lars

    2015-01-01

    Pure alexia is a severe impairment of word reading in which individuals process letters serially with a pronounced length effect. Yet, there is considerable variation in the performance of alexic readers with generally very slow, but also occasionally fast responses, an observation addressed rarely in previous reports. It has been suggested that "fast" responses in pure alexia reflect residual parallel letter processing or that they may even be subserved by an independent reading system. Four experiments assessed fast and slow reading in a participant (DN) with pure alexia. Two behavioral experiments investigated frequency, neighborhood, and length effects in forced fast reading. Two further experiments measured eye movements when DN was forced to read quickly, or could respond faster because words were easier to process. Taken together, there was little support for the proposal that "qualitatively different" mechanisms or reading strategies underlie both types of responses in DN. Instead, fast responses are argued to be generated by the same serial-reading strategy.

  13. Noninformative prior in the quantum statistical model of pure states

    NASA Astrophysics Data System (ADS)

    Tanaka, Fuyuhiko

    2012-06-01

    In the present paper, we consider a suitable definition of a noninformative prior on the quantum statistical model of pure states. While the full pure-states model is invariant under unitary rotation and admits the Haar measure, restricted models, which we often see in quantum channel estimation and quantum process tomography, have less symmetry and no compelling rationale for any choice. We adopt a game-theoretic approach that is applicable to classical Bayesian statistics and yields a noninformative prior for a general class of probability distributions. We define the quantum detection game and show that there exist noninformative priors for a general class of a pure-states model. Theoretically, it gives one of the ways that we represent ignorance on the given quantum system with partial information. Practically, our method proposes a default distribution on the model in order to use the Bayesian technique in the quantum-state tomography with a small sample.

  14. Faithful Transfer Arbitrary Pure States with Mixed Resources

    NASA Astrophysics Data System (ADS)

    Luo, Ming-Xing; Li, Lin; Ma, Song-Ya; Chen, Xiu-Bo; Yang, Yi-Xian

    2013-09-01

    In this paper, we show that some special mixed quantum resource experience the same property of pure entanglement such as Bell state for quantum teleportation. It is shown that one mixed state and three bits of classical communication cost can be used to teleport one unknown qubit compared with two bits via pure resources. The schemes are easily implement with model physical techniques. Moreover, these resources are also optimal and typical for faithfully remotely prepare an arbitrary qubit, two-qubit and three-qubit states with mixed quantum resources. Our schemes are completed as same as those with pure quantum entanglement resources except only 1 bit additional classical communication cost required. The success probability is independent of the form of the mixed resources.

  15. Fisher-Symmetric Informationally Complete Measurements for Pure States.

    PubMed

    Li, Nan; Ferrie, Christopher; Gross, Jonathan A; Kalev, Amir; Caves, Carlton M

    2016-05-01

    We introduce a new kind of quantum measurement that is defined to be symmetric in the sense of uniform Fisher information across a set of parameters that uniquely represent pure quantum states in the neighborhood of a fiducial pure state. The measurement is locally informationally complete-i.e., it uniquely determines these parameters, as opposed to distinguishing two arbitrary quantum states-and it is maximal in the sense of a multiparameter quantum Cramér-Rao bound. For a d-dimensional quantum system, requiring only local informational completeness allows us to reduce the number of outcomes of the measurement from a minimum close to but below 4d-3, for the usual notion of global pure-state informational completeness, to 2d-1. PMID:27203310

  16. Fuel loading and homogeneity analysis of HFIR design fuel plates loaded with uranium silicide fuel

    SciTech Connect

    Blumenfeld, P.E.

    1995-08-01

    Twelve nuclear reactor fuel plates were analyzed for fuel loading and fuel loading homogeneity by measuring the attenuation of a collimated X-ray beam as it passed through the plates. The plates were identical to those used by the High Flux Isotope Reactor (HFIR) but were loaded with uranium silicide rather than with HFIR`s uranium oxide fuel. Systematic deviations from nominal fuel loading were observed as higher loading near the center of the plates and underloading near the radial edges. These deviations were within those allowed by HFIR specifications. The report begins with a brief background on the thermal-hydraulic uncertainty analysis for the Advanced Neutron Source (ANS) Reactor that motivated a statistical description of fuel loading and homogeneity. The body of the report addresses the homogeneity measurement techniques employed, the numerical correction required to account for a difference in fuel types, and the statistical analysis of the resulting data. This statistical analysis pertains to local variation in fuel loading, as well as to ``hot segment`` analysis of narrow axial regions along the plate and ``hot streak`` analysis, the cumulative effect of hot segment loading variation. The data for all twelve plates were compiled and divided into 20 regions for analysis, with each region represented by a mean and a standard deviation to report percent deviation from nominal fuel loading. The central regions of the plates showed mean values of about +3% deviation, while the edge regions showed mean values of about {minus}7% deviation. The data within these regions roughly approximated random samplings from normal distributions, although the chi-square ({chi}{sup 2}) test for goodness of fit to normal distributions was not satisfied.

  17. Actuating dielectric elastomers in pure shear deformation by elastomeric conductors

    SciTech Connect

    Wang, Yin; Chen, Baohong; Zhou, Jinxiong; Bai, Yuanyuan; Wang, Hong

    2014-02-10

    Pure shear experiments are commonly used to characterize dielectric elastomer (DE) material properties and to evaluate DE actuator/generator performance. It is increasingly important for many applications to replace conventional carbon grease electrodes with stretchable elastomeric conductors. We formulate a theory for DE with elastomeric conductors, synthesize transparent hydrogel as ionic conductors, and measure actuation of DE in pure shear deformation. Maximum 67% actuation strain is demonstrated. The theory agrees well with our measurement and also correlates well with reported experiments on DE with electronic conductors.

  18. Six open string disk amplitude in pure spinor superspace

    NASA Astrophysics Data System (ADS)

    Mafra, Carlos R.; Schlotterer, Oliver; Stieberger, Stephan; Tsimpis, Dimitrios

    2011-05-01

    The tree-level amplitude of six massless open strings is computed using the pure spinor formalism. The OPE poles among integrated and unintegrated vertices can be efficiently organized according to the cohomology of pure spinor superspace. The identification and use of these BRST structures and their interplay with the system of equations fulfilled by the generalized Euler integrals allow the full supersymmetric six-point amplitude to be written in compact form. Furthermore, the complete set of extended Bern-Carrasco-Johansson relations are derived from the monodromy properties of the disk world-sheet and explicitly verified for the supersymmetric numerator factors.

  19. PURE CULTIVATION IN VIVO OF VACCINE VIRUS FREE FROM BACTERIA

    PubMed Central

    Noguchi, Hideyo

    1915-01-01

    Vaccine virus freed from all associated bacteria by means of suitable disinfecting agents can be propagated in a pure state in the testicles of rabbits and bulls. The virus cultivated in this manner is not only devoid of all bacteria, but appears capable of indefinite transfer from one animal to another. Sixty passages in rabbits of a pure strain have been made within one year. Several transfers from testicle to testicle are required to bring about accurate adaptation of the virus to the testicular parenchyma, so that continued propagation in this way can be certainly secured. During the first transfers from testicle to testicle the activity of the virus may be less than the original skin specimen from which the pure strain was derived; but as the transfers proceed the activity rises until, when the adaptation is complete, the activity of the testicular equals that of the skin strain. The multiplication of the virus within the testicle is maximum on the fourth or fifth day after inoculation; the quantity of virus remains about stationary until the eighth day, when diminution begins. At the expiration of five weeks no more virus could be detected in the testicle. The vaccinal processes in the skin, cornea, and testicle of rabbits are practically identical whether the virus employed for the inoculation has been the original skin strain or the pure testicular strain; and the skin lesions produced in the calf with the two strains are also identical. In conformity with the finding mentioned in the last paragraph it has been found that human beings react to the pure testicular strain of vaccine virus in an entirely typical manner. In the case both of original vaccination and revaccination the vaccinal effects cannot be distinguished from those arising from uncomplicated skin virus. Pure strains of testicular virus are readily produced, and once secured they may be propagated in a pure state by the method described in rabbits or bulls without difficulty and with economy

  20. Clinical study of 222 patients with pure motor stroke

    PubMed Central

    Arboix, A; Padilla, I; Massons, J; Garcia-Eroles, L; Comes, E; Targa, C

    2001-01-01

    The objective was to assess the frequency of pure motor stroke caused by different stroke subtypes and to compare demographic, clinical, neuroimaging, and outcome data of pure motor stroke with those of patients with other lacunar stroke as well as with those of patients with non-lacunar stroke.
Data from 2000 patients with acute stroke (n=1761) or transient ischaemic attack (n=239) admitted consecutively to the department of neurology of an acute care 350 bed teaching hospital were prospectively collected in the Sagrat Cor Hospital of Barcelona stroke registry over a 10 year period. For the purpose of the study 222 (12.7%) patients with pure motor stroke were selected. The other study groups included 218 (12.3%) patients with other lacunar strokes and 1321 (75%) patients with non-lacunar stroke.
In relation to stroke subtype, lacunar infarcts were found in 189 (85%) patients, whereas ischaemic lacunar syndromes not due to lacunar infarcts occurred in 23 (10.4%) patients (atherothrombotic stroke in 12, cardioembolic stroke in seven, infarction of undetermined origin in three, and infarction of unusual aetiology in one) and haemorrhagic lacunar syndromes in 10 (4.5%). Patients with pure motor stroke showed a better outcome than patients with non-lacunar stroke with a significantly lower number of complications and in hospital mortality rate, shorter duration of hospital stay, and a higher number of symptom free patients at hospital discharge. After multivariate analysis, hypertension, diabetes, obesity, hyperlipidaemia, non-sudden stroke onset, internal capsule involvement, and pons topography seemed to be independent factors of pure motor stroke in patients with acute stroke.
In conclusion, about one of every 10 patients with acute stroke had a pure motor stroke. Pure motor stroke was caused by a lacunar infarct in 85% of patients and by other stroke subtypes in 15%. Several clinical features are more frequent in patients with pure motor stroke than in

  1. Pure tone audiometry: comparison of general practice and hospital services

    PubMed Central

    Smith, Michael C.F.; Cable, Hugh R.; Wilmot, John F.

    1988-01-01

    Pure tone audiometry was obtained for both ears of 32 children by a general practitioner using a simple audiometer in his surgery, and by audiometricians in a hospital department on the same day. Comparing the worst hearing threshold at any of the three tested frequencies, the general practitioner did not find any ears to hear more than 10 dB better than the hospital (no false negatives). However, there were six false positives (9%) where the general practitioner identified an apparent hearing loss of greater than 15 dB. It is concluded that pure tone audiometry could be carried out accurately in the practice. PMID:3267745

  2. Load Balancing Scientific Applications

    SciTech Connect

    Pearce, Olga Tkachyshyn

    2014-12-01

    The largest supercomputers have millions of independent processors, and concurrency levels are rapidly increasing. For ideal efficiency, developers of the simulations that run on these machines must ensure that computational work is evenly balanced among processors. Assigning work evenly is challenging because many large modern parallel codes simulate behavior of physical systems that evolve over time, and their workloads change over time. Furthermore, the cost of imbalanced load increases with scale because most large-scale scientific simulations today use a Single Program Multiple Data (SPMD) parallel programming model, and an increasing number of processors will wait for the slowest one at the synchronization points. To address load imbalance, many large-scale parallel applications use dynamic load balance algorithms to redistribute work evenly. The research objective of this dissertation is to develop methods to decide when and how to load balance the application, and to balance it effectively and affordably. We measure and evaluate the computational load of the application, and develop strategies to decide when and how to correct the imbalance. Depending on the simulation, a fast, local load balance algorithm may be suitable, or a more sophisticated and expensive algorithm may be required. We developed a model for comparison of load balance algorithms for a specific state of the simulation that enables the selection of a balancing algorithm that will minimize overall runtime.

  3. Influence of varying compressive loading methods on physiologic motion patterns in the cervical spine.

    PubMed

    Bell, Kevin M; Yan, Yiguo; Debski, Richard E; Sowa, Gwendolyn A; Kang, James D; Tashman, Scott

    2016-01-25

    The human cervical spine supports substantial compressive load in-vivo arising from muscle forces and the weight of the head. However, the traditional in-vitro testing methods rarely include compressive loads, especially in investigations of multi-segment cervical spine constructs. Various methods of modeling physiologic loading have been reported in the literature including axial forces produced with inclined loading plates, eccentric axial force application, follower load, as well as attempts to individually apply/model muscle forces in-vitro. The importance of proper compressive loading to recreate the segmental motion patterns exhibited in-vivo has been highlighted in previous studies. However, appropriate methods of representing the weight of head and muscle loading are currently unknown. Therefore, a systematic comparison of standard pure moment with no compressive loading versus published and novel compressive loading techniques (follower load - FL, axial load - AL, and combined load - CL) was performed. The present study is unique in that a direct comparison to continuous cervical kinematics over the entire extension to flexion motion path was possible through an ongoing intra-institutional collaboration. The pure moment testing protocol without compression or with the application of follower load was not able to replicate the typical in-vivo segmental motion patterns throughout the entire motion path. Axial load or a combination of axial and follower load was necessary to mimic the in-vivo segmental contributions at the extremes of the extension-flexion motion path. It is hypothesized that dynamically altering the compressive loading throughout the motion path is necessary to mimic the segmental contribution patterns exhibited in-vivo. PMID:26708967

  4. Load estimator (LOADEST): a FORTRAN program for estimating constituent loads in streams and rivers

    USGS Publications Warehouse

    Runkel, Robert L.; Crawford, Charles G.; Cohn, Timothy A.

    2004-01-01

    LOAD ESTimator (LOADEST) is a FORTRAN program for estimating constituent loads in streams and rivers. Given a time series of streamflow, additional data variables, and constituent concentration, LOADEST assists the user in developing a regression model for the estimation of constituent load (calibration). Explanatory variables within the regression model include various functions of streamflow, decimal time, and additional user-specified data variables. The formulated regression model then is used to estimate loads over a user-specified time interval (estimation). Mean load estimates, standard errors, and 95 percent confidence intervals are developed on a monthly and(or) seasonal basis. The calibration and estimation procedures within LOADEST are based on three statistical estimation methods. The first two methods, Adjusted Maximum Likelihood Estimation (AMLE) and Maximum Likelihood Estimation (MLE), are appropriate when the calibration model errors (residuals) are normally distributed. Of the two, AMLE is the method of choice when the calibration data set (time series of streamflow, additional data variables, and concentration) contains censored data. The third method, Least Absolute Deviation (LAD), is an alternative to maximum likelihood estimation when the residuals are not normally distributed. LOADEST output includes diagnostic tests and warnings to assist the user in determining the appropriate estimation method and in interpreting the estimated loads. This report describes the development and application of LOADEST. Sections of the report describe estimation theory, input/output specifications, sample applications, and installation instructions.

  5. Adolescence. What is normal?

    PubMed

    Offer, D; Ostrov, E; Howard, K I

    1989-06-01

    We present in some detail what constitutes normal behavior, or mental health, among teenagers. Our data are based on the results of a specially devised psychological questionnaire by one of us (D.O.). This questionnaire has been shown to reliably distinguish mentally healthy from psychiatrically disturbed populations. Results are presented across three decades (1960s, 1970s, and 1980s), across genders, and across the high school years. A conceptual framework is presented to help the clinician working with adolescents to understand the fluctuation in psychopathology among youth. Adolescent density in the total population is shown to be a significant factor in determining the rate of disturbance among teenagers. Our research findings demonstrate that the rate of behavioral disturbance among adolescents is the same as in other parts of the life cycle. The clinician working with adolescents tends to underestimate the severity of adolescent problems because of the near-universal belief that all adolescents undergo "adolescent turmoil." We have found that adolescents who are experiencing turmoil need professional help.

  6. Brain spatial normalization.

    PubMed

    Bug, William; Gustafson, Carl; Shahar, Allon; Gefen, Smadar; Fan, Yingli; Bertrand, Louise; Nissanov, Jonathan

    2007-01-01

    Neuroanatomical informatics, a subspecialty of neuroinformatics, focuses on technological solutions to neuroimage database access. Its current main goal is an image-based query system that is able to retrieve imagery based on anatomical location. Here, we describe a set of tools that collectively form such a solution for sectional material and that are available to investigators to use on their own data sets. The system accepts slide images as input and yields a matrix of transformation parameters that map each point on the input image to a standardized 3D brain atlas. In essence, this spatial normalization makes the atlas a spatial indexer from which queries can be issued simply by specifying a location on the reference atlas. Our objective here is to familiarize potential users of the system with the steps required of them as well as steps that take place behind the scene. We detail the capabilities and the limitations of the current implementation and briefly describe the enhancements planned for the near future.

  7. [Normal aging and cognition].

    PubMed

    Ska, Bernadette; Joanette, Yves

    2006-03-01

    It is now well documented that normal aging modifies the cognitive functioning and most observations suggest that cognition evolves in the direction of deterioration. The more frequently impaired functions are memory, attention and visual-spatial abilities. On the other hand, some abilities seem to increase, such as vocabulary. Considering the aging effect on cognition, questions remain regarding directionality, universality and reversibility. A great variability in aged related impacts is observed among subjects and among cognitive domains. Some individuals evolved more rapidly than others. Some cognitive functions are more affected by aging than others. General and specific factors are hypothesized to explain the aged related cognitive decline. Among them, educational level, health, cognitive style, life style, personality, are likely to modulate the aged related cognitive evolution by influencing attentional resources and cerebral plasticity. Cognitive resources are essential to develop adaptative strategies. During the life span, resources are activated and increased by learning and training. Considering the role of cognitive resources, successful aging is dependent on several conditions : absence of disease leading to a loss of autonomy, maintenance of cognitive and physical activities, and active and social engaged lifestyle. PMID:16527210

  8. The normal antireflux mechanism.

    PubMed

    Paterson, W G

    2001-08-01

    The normal antireflux mechanism consists of several components, any one of which may malfunction and render an individual prone to the development of GERD. The LES is clearly the most important component because gastroesophageal reflux almost always occurs when the sphincter pressure equals that of the stomach. Usually, an LES pressure of just 2 to 3 mm Hg above intragastric pressure is sufficient to prevent reflux. Other factors certainly play significant ancillary roles in preventing reflux. In the absence of a hiatal hernia, the crural fibers of the diaphragm serve as an "extrinsic" sphincter. Furthermore, the unique anatomy of the proximal stomach (e.g., the angle of His, mucosal flap valve, posterolateral location of the fundus) serves to keep gastric contents away from the gastroesophageal junction, making it less likely for reflux to occur when the LES relaxes. When a hiatal hernia is present, these factors are lost, and the hernia sac provides a reservoir for gastric juices with ready access to the LES. Finally, some degree of reflux occurs in all individuals, but esophageal clearance and acid neutralization provide an important last line of defense.

  9. Influence of oxidation treatment on fatigue and fatigue-induced damage of commercially pure titanium.

    PubMed

    Leinenbach, C; Eifler, D

    2009-09-01

    In this investigation, the cyclic deformation behaviour of commercially pure titanium was characterized in axial stress controlled constant amplitude and load increase tests, as well as in rotating bending tests. The influence of different clinically relevant surface treatments (polishing, thermal and anodic oxidizing) on the fatigue behaviour was investigated. All tests were realized in oxygen-saturated Ringer's solution. The cyclic deformation behaviour was characterized by mechanical hysteresis measurements. In addition, the change of the free corrosion potential and the corrosion current during the fatigue tests in simulated physiological media indicated such types of surface damage as slip bands, microcracks and oxide film ablation. Microstructural changes on the specimen surfaces were examined by scanning electron microscopy. PMID:19394905

  10. Risk Quantification for ANN Based Short-Term Load Forecasting

    NASA Astrophysics Data System (ADS)

    Iwashita, Daisuke; Mori, Hiroyuki

    A new risk assessment method for short-term load forecasting is proposed. The proposed method makes use of an Artificial Neural Network (ANN) to forecast one-step ahead daily maximum loads and evaluate uncertainty of in load forecasting. As ANN the model, the Radial Basis Function (RBF) network is employed to forecast loads due to the good performance. Sufficient realistic pseudo-scenarios are required to carry out quantitative risk analysis. The multivariate normal distribution with the correlation between input variables is used to give more realistic results to ANN. In addition, the method of Moment Matching is used to improve the accuracy of the multivariate normal distribution. The Peak Over Threshold (POT) approach is used to evaluate risk that exceeds the upper bounds of generation capacity. The proposed method is successfully applied to real data of daily maximum load forecasting.

  11. Institutionalizing Normal: Rethinking Composition's Precedence in Normal Schools

    ERIC Educational Resources Information Center

    Skinnell, Ryan

    2013-01-01

    Composition historians have recently worked to recover histories of composition in normal schools. This essay argues, however, that historians have inadvertently misconstrued the role of normal schools in American education by inaccurately comparing rhetorical education in normal schools to rhetorical education in colleges and universities.…

  12. Tar loads on Omani beaches

    SciTech Connect

    Badawy, M.I.; Al-Harthy, F.T. )

    1991-11-01

    Owing to Oman's geographic position and long coastal line, the coastal areas of Oman are particularly vulnerable to oil pollution from normal tanker operations, illegal discharges, and accidental spills as well as local sources of oil input. UNEP carried out a survey on the coasts of Oman to determine the major sources of oil pollution and concluded that the major shoreline pollution problems in Oman arose from operational discharges of oil from passing vessels traffic. The oil, because of the high sea and air temperatures in the area, was subjected to relatively high rates of evaporation and photo-oxidation and tended to arrive at the coast as heavy petroleum particulate residues (tar balls). The aim of the present study was to measure the loads of tar balls in Omani coastal areas and to identify the source of oil pollutants on beaches.

  13. Hydrodynamic lubrication of rigid nonconformal contacts in combined rolling and normal motion

    NASA Technical Reports Server (NTRS)

    Ghosh, M. K.; Hamrock, B. J.; Brewe, D. E.

    1984-01-01

    A numerical solution to the problem of hydrodynamic lubrication of rigid point contacts with an isoviscous, incompressible lubricant was obtained. The hydrodynamic load-carrying capacity under unsteady (or dynamic) conditions arising from the combined effects of squeeze motion superposed upon the entraining motion was determined for both normal approach and separation. Superposed normal motion considerably increases net load-carrying capacity during normal approach and substantially reduces net load-carrying capacity during separation. Geometry was also found to have a significant influence on the dynamic load-carrying capacity. The ratio of dynamic to steady state load-carrying capacity increases with increasing geometry parameter for normal approach and decreases during separation. The cavitation (film rupture) boundary is also influenced significantly by the normal motion, moving downstream during approach and upstream during separation. For sufficiently high normal separation velocity the rupture boundary may even move upstream of the minimum-film-thickness position. Sixty-three cases were used to derive a functional relationship for the ratio of the dynamic to steady state load-carrying capacity in terms of the dimensionless normal velocity parameter (incorporating normal velocity, entraining velocity, and film thickness) and the geometry parameter.

  14. Recovery of pure ZnO nanoparticles from spent Zn-MnO₂ alkaline batteries.

    PubMed

    Deep, Akash; Kumar, Kamal; Kumar, Parveen; Kumar, Pawan; Sharma, Amit L; Gupta, Bina; Bharadwaj, Lalit M

    2011-12-15

    The recovery of pure ZnO (zinc oxide) nanoparticles from spent Zn-Mn dry alkaline batteries is reported. Spent batteries were dismantled to separate the contained valuable metals of the cell electrodes in the form of black powder. Treatment of this black powder with 5 mol L(-1) HCl produced leach liquor, primarily containing 2.90 g L(-1) Zn and 2.02 g L(-1) Mn. Selective and quantitative liquid-liquid extraction of Zn(II) was then carried out in three counter current steps by using Cyanex 923 (0.10 mol L(-1) in n-hexane). Zn(II) distributed in the organic phase as complex ZnCl(2)·2R (R = Cyanex 923 molecule). The metal loaded organic phase was subjected to combust at 600 °C to yield pure ZnO nanoparticles (40-50 nm). Important characteristics of the synthesized nanoparticles were investigated by field emission scanning electron microscopy (FESEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction spectroscopy (XRD), and atomic force microscopy (AFM).

  15. Continuous analysis of stresses from arbitrary surface loads on a half space

    NASA Technical Reports Server (NTRS)

    Bell, J. C.

    1980-01-01

    A new form of elemental surface load on a half space is introduced, presuming a quasi-pyramidal variation of load which is doubly linear in each of four rectangular parts of a surface rectangle. Approximations of arbitrary load distributions by sums of such elements are continuous, piecewise linear in two directions and well adaptable. The loads may be normal or tangential. The explicit solutions obtained for all stress and displacement components due to each elemental load involve only elementary functions, are free of the discontinuities which arise with stepwise elements, and are suitable for computing. Some illustrative stress distributions are presented for elemental loads and for multiple pyramidal loads involving both normal and tangential loads. The value of the load continuity in the more complicated analyses of surface cracks is also illustrated.

  16. Computer Aided Biomanufacturing of Mechanically Robust Pure Collagen Meshes with Controlled Macroporosity

    PubMed Central

    Islam, Anowarul; Chapin, Katherine; Younesi, Mousa

    2015-01-01

    Reconciliation of high strength and high porosity in pure collagen based structures is a major barrier in collagen’s use in load-bearing applications. The current study developed a CAD/CAM based electrocompaction method to manufacture highly porous patterned scaffolds using pure collagen. Utilization of computerized scaffold design and fabrication allows the integration of mesh-scaffolds with controlled pore size, shape and spacing. Mechanical properties of fabricated collagen meshes were investigated as a function of number of patterned layers, and with different pore geometries. The tensile stiffness, tensile strength and modulus ranges from 10-50 N/cm, 1-6 MPa and 5-40 MPa respectively for all the scaffold groups. These results are within the range of practical usability of different tissue engineering application such as tendon, hernia, stress urinary incontinence or thoracic wall reconstruction. Moreover, 3-fold increase in the layer number resulted in more than 5-fold increases in failure load, toughness and stiffness which suggests that by changing the number of layers and shape of the structure, mechanical properties can be modulated for the aforementioned tissue engineering application. These patterned scaffolds offer a porosity ranging from 0.8-1.5 mm in size, a range that is commensurate with pore sizes of repair meshes in the market. The connected macroporosity of the scaffolds facilitated cell-seeding such that cells populated the entire scaffold at the time of seeding. After 3 days of culture, cell nuclei became elongated. These results indicate that the patterned electrochemical deposition method in this study was able to develop mechanically robust, highly porous collagen scaffolds with controlled porosity which not only tries to solve one of the major tissue engineering problems in a fundamental level but also has a significant potential to be used in different tissue engineering applications. PMID:26200002

  17. Pitch strength of normal and dysphonic voices

    PubMed Central

    Shrivastav, Rahul; Eddins, David A.; Anand, Supraja

    2012-01-01

    Two sounds with the same pitch may vary from each other based on saliency of their pitch sensation. This perceptual attribute is called “pitch strength.” The study of voice pitch strength may be important in quantifying of normal and pathological qualities. The present study investigated how pitch strength varies across normal and dysphonic voices. A set of voices (vowel /a/) selected from the Kay Elemetrics Disordered Voice Database served as the stimuli. These stimuli demonstrated a wide range of voice quality. Ten listeners judged the pitch strength of these stimuli in an anchored magnitude estimation task. On a given trial, listeners heard three different stimuli. The first stimulus represented very low pitch strength (wide-band noise), the second stimulus consisted of the target voice and the third stimulus represented very high pitch strength (pure tone). Listeners estimated pitch strength of the target voice by positioning a continuous slider labeled with values between 0 and 1, reflecting the two anchor stimuli. Results revealed that listeners can judge pitch strength reliably in dysphonic voices. Moderate to high correlations with perceptual judgments of voice quality suggest that pitch strength may contribute to voice quality judgments. PMID:22423721

  18. Phloem loading: an integrated approach

    SciTech Connect

    Wilson, C.

    1986-01-01

    This study focuses on the regulation of sucrose transport across the plasmalemma. Initially, we re-examined the use of leaf discs to study the kinetics of phloem loading using Allium cepa leaves. All tissues exhibited the same linear plus saturable profile as Beta vulgaris, except fructose uptake into the inner parenchyma and bundle-sheath cells; in this case the response was linear. These results indicate that all tissues of the leaf retrieve exogenous sucrose such that kinetics from leaf discs cannot be taken to represent phloem loading per se. We continued our study by investigating the influence of internal sugars on sugar transport across the plasmalemma. We found that if internal sugars were manipulated by heat-girdling techniques or DCMU treatment there was no appreciable change in sucrose influx. However, longer term heat-girdling decreased sucrose uptake. These data indicate that carbohydrate partitioning among the chloroplast, cytosol, and vacuole modulates cytosolic sugar levels. One interesting discovery was that leaves excised from the plant and allowed to undergo their normal day/night cycle do not transfer (/sup 14/C) sucrose to their minor veins.

  19. The partially closed Griffith crack. [under polynomial loads

    NASA Technical Reports Server (NTRS)

    Thresher, R. W.; Smith, F. W.

    1973-01-01

    A solution is presented for a Griffith crack subjected to an arbitrary polynomial loading function which causes one end of the crack to remain closed. Closed form expressions are presented for the crack opening length and for the stress and displacements in the plane of the crack. The special case of pure bending is presented as an example and for this case the stress intensity factor is computed.

  20. Idealization in Chemistry: Pure Substance and Laboratory Product

    ERIC Educational Resources Information Center

    Fernández-González, Manuel

    2013-01-01

    This article analyzes the concept of idealization in chemistry and the role played by pure substance and laboratory product. This topic has evident repercussions in the educational contexts that are applied to the science classroom, which are highlighted throughout the text. A common structure for knowledge construction is proposed for both…

  1. About the Role of Visual Field Defects in Pure Alexia

    ERIC Educational Resources Information Center

    Pflugshaupt, Tobias; Gutbrod, Klemens; Wurtz, Pascal; von Wartburg, Roman; Nyffeler, Thomas; de Haan, Bianca; Karnath, Hans-Otto; Mueri, Rene M.

    2009-01-01

    Pure alexia is an acquired reading disorder characterized by a disproportionate prolongation of reading time as a function of word length. Although the vast majority of cases reported in the literature show a right-sided visual defect, little is known about the contribution of this low-level visual impairment to their reading difficulties. The…

  2. Effect of dissociation on thermodynamic properties of pure diatomic gases

    NASA Technical Reports Server (NTRS)

    Woolley, Harold W

    1955-01-01

    A graphical method is described by which the enthalpy, entropy, and compressibility factor for the equilibrium mixture of atoms and diatomic molecules for pure gaseous elements may be obtained and shown for any dissociating element for which the necessary data exist. Results are given for hydrogen, oxygen, and nitrogen. The effect of dissociation on the heat capacity is discussed briefly.

  3. Chemical modification of pure titanium surfaces for oral implants.

    PubMed

    Pimenta, J; Castro, F

    1999-01-01

    A technique that achieves different pure titanium surfaces depending on acid concentration and exposure time is described. It is possible to obtain, with the same chemical treatment, both large pits and small rugosities. This technique may have interesting applications in oral implants.

  4. Complex windmill transformation producing new purely magnetic fluids

    NASA Astrophysics Data System (ADS)

    Lozanovski, C.; Wylleman, L.

    2011-04-01

    Minimal complex windmill transformations of G2IB(ii) spacetimes (admitting a two-dimensional Abelian group of motions of the so-called Wainwright B(ii) class) are defined and the compatibility with a purely magnetic Weyl tensor is investigated. It is shown that the transformed spacetimes cannot be perfect fluids or purely magnetic Einstein spaces. We then determine which purely magnetic perfect fluids (PMpfs) can be windmill-transformed into purely magnetic anisotropic fluids (PMafs). Assuming separation of variables, complete integration produces two, algebraically general, G2I-B(ii) PMpfs: a solution with zero 4-acceleration vector and spatial energy-density gradient, previously found by the authors, and a new solution in terms of Kummer's functions, where these vectors are aligned and non-zero. The associated windmill PMafs are rotating but non-expanding. Finally, an attempt to relate the spacetimes to each other by a simple procedure leads to a G2I-B(ii) one-parameter PMaf generalization of the previously found metric.

  5. Pure Mediated Priming: A Retrospective Semantic Matching Model

    ERIC Educational Resources Information Center

    Jones, Lara L.

    2010-01-01

    Mediated priming refers to the activation of a target (e.g., "stripes") by a prime (e.g., "lion") that is related indirectly via a connecting mediator (e.g., tiger). In previous mediated priming studies (e.g., McNamara & Altarriba, 1988), the mediator was associatively related to the prime. In contrast, pure mediated priming (e.g., "spoon" [right…

  6. A pure-sampling quantum Monte Carlo algorithm

    SciTech Connect

    Ospadov, Egor; Rothstein, Stuart M.

    2015-01-14

    The objective of pure-sampling quantum Monte Carlo is to calculate physical properties that are independent of the importance sampling function being employed in the calculation, save for the mismatch of its nodal hypersurface with that of the exact wave function. To achieve this objective, we report a pure-sampling algorithm that combines features of forward walking methods of pure-sampling and reptation quantum Monte Carlo (RQMC). The new algorithm accurately samples properties from the mixed and pure distributions simultaneously in runs performed at a single set of time-steps, over which extrapolation to zero time-step is performed. In a detailed comparison, we found RQMC to be less efficient. It requires different sets of time-steps to accurately determine the energy and other properties, such as the dipole moment. We implement our algorithm by systematically increasing an algorithmic parameter until the properties converge to statistically equivalent values. As a proof in principle, we calculated the fixed-node energy, static α polarizability, and other one-electron expectation values for the ground-states of LiH and water molecules. These quantities are free from importance sampling bias, population control bias, time-step bias, extrapolation-model bias, and the finite-field approximation. We found excellent agreement with the accepted values for the energy and a variety of other properties for those systems.

  7. Pure Spinor Formalism for Osp N\\vert 4) Backgrounds

    NASA Astrophysics Data System (ADS)

    Fré, Pietro; Grassi, Pietro Antonio

    2012-12-01

    We start from the Maurer-Cartan (MC) equations of the Osp(N\\vert 4) superalgebras satisfied by the left-invariant superforms realized on supercoset manifolds of the corresponding supergroups and we derive some new pure spinor constraints. They are obtained by "ghostifying" the MC forms and extending the differential d to a BRST differential. From the superalgebras \\hat G = Osp(N\\vert 4) we single out different subalgebras H \\subset \\hat G associated with the different cosets \\hat {G}/H: each choice of ℍ leads to a different weakening of the pure spinor constraints. In each case, the number of parameter is counted and we show that in the cases of Osp(6|4)/U(3)×SO(1, 3), Osp(4|4)/SO(3) ×SO(1, 3) and finally Osp(4|4)/U(2) ×SO(1, 3) the bosonic and fermionic degrees of freedom match in order to provide a c = 0 superconformal field theory. We construct both the Green-Schwarz and the pure spinor sigma model for the case Osp(6|4)/U(3)×SO(1, 3) corresponding to AdS4 ×ℙ3. The pure spinor sigma model can be consistently quantized.

  8. Number Reading in Pure Alexia--A Review

    ERIC Educational Resources Information Center

    Starrfelt, Randi; Behrmann, Marlene

    2011-01-01

    It is commonly assumed that number reading can be intact in patients with pure alexia, and that this dissociation between letter/word recognition and number reading strongly constrains theories of visual word processing. A truly selective deficit in letter/word processing would strongly support the hypothesis that there is a specialized system or…

  9. Three Variations on a Theme: The Power of Pure Empathy.

    ERIC Educational Resources Information Center

    Kottler, Jeffrey A.; Montgomery, Marilyn J.; Marbley, Aretha Faye

    1998-01-01

    With the counseling profession's increased emphasis on developing brief therapies, applying innovative techniques, and measuring outcomes, helping someone feel understood is sometimes neglected. Three narratives by humanistic practitioners illustrate the value of pure empathy in our work with clients, students, and others in our diverse…

  10. 77 FR 59979 - Pure Magnesium (Granular) From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-01

    ... this five-year review. Background The Commission instituted this review on February 1, 2012 (77 FR 5049) and determined on May 7, 2012 that it would conduct an expedited review (77 FR 32668, June 1, 2012... COMMISSION Pure Magnesium (Granular) From China Determination On the basis of the record \\1\\ developed in...

  11. In vitro degradation of pure Mg in response to glucose

    PubMed Central

    Zeng, Rong-Chang; Li, Xiao-Ting; Li, Shuo-Qi; Zhang, Fen; Han, En-Hou

    2015-01-01

    Magnesium and its alloys are promising biodegradable biomaterials but are still challenging to be used in person with high levels of blood glucose or diabetes. To date, the influence of glucose on magnesium degradation has not yet been elucidated, this issue requires more attention. Herein, we present pure Mg exhibiting different corrosion responses to saline and Hank’s solutions with different glucose contents, and the degradation mechanism of pure Mg in the saline solution with glucose in comparison with mannitol as a control. On one hand, the corrosion rate of pure Mg increases with the glucose concentration in saline solutions. Glucose rapidly transforms into gluconic acid, which attacks the oxides of the metal and decreases the pH of the solution; it also promotes the absorption of chloride ions on the Mg surface and consequently accelerates corrosion. On the other hand, better corrosion resistance is obtained with increasing glucose content in Hank’s solution due to the fact that glucose coordinates Ca2+ ions in Hank’s solution and thus improves the formation of Ca-P compounds on the pure Mg surface. This finding will open up new avenues for research on the biodegradation of bio-Mg materials in general, which could yield many new and interesting results. PMID:26264413

  12. Molarity (Aromic Density) of the Elements as Pure Crystals.

    ERIC Educational Resources Information Center

    Pauling, Linus; Herman, Zelek S.

    1985-01-01

    Provides background information for teachers on the atomic density of the elements as pure crystals. Atomic density is defined as the reciprocal of the atomic volume. Includes atomic-density diagrams which were prepared using the atomic-volume values given by Singman, supplemented by additional values for some allotropes. (JN)

  13. A Graphical Representation for the Fugacity of a Pure Substance

    ERIC Educational Resources Information Center

    Book, Neil L.; Sitton, Oliver C.

    2010-01-01

    The thermodynamic equations used to define and compute the fugacity of a pure substance are depicted as processes on a semi-logarithmic plot of pressure vs. molar Gibbs energy (PG diagram) with isotherms for the substance behaving as an ideal gas superimposed. The PG diagram clearly demonstrates the physical basis for the definitions and the…

  14. In vitro degradation of pure Mg in response to glucose

    NASA Astrophysics Data System (ADS)

    Zeng, Rong-Chang; Li, Xiao-Ting; Li, Shuo-Qi; Zhang, Fen; Han, En-Hou

    2015-08-01

    Magnesium and its alloys are promising biodegradable biomaterials but are still challenging to be used in person with high levels of blood glucose or diabetes. To date, the influence of glucose on magnesium degradation has not yet been elucidated, this issue requires more attention. Herein, we present pure Mg exhibiting different corrosion responses to saline and Hank’s solutions with different glucose contents, and the degradation mechanism of pure Mg in the saline solution with glucose in comparison with mannitol as a control. On one hand, the corrosion rate of pure Mg increases with the glucose concentration in saline solutions. Glucose rapidly transforms into gluconic acid, which attacks the oxides of the metal and decreases the pH of the solution; it also promotes the absorption of chloride ions on the Mg surface and consequently accelerates corrosion. On the other hand, better corrosion resistance is obtained with increasing glucose content in Hank’s solution due to the fact that glucose coordinates Ca2+ ions in Hank’s solution and thus improves the formation of Ca-P compounds on the pure Mg surface. This finding will open up new avenues for research on the biodegradation of bio-Mg materials in general, which could yield many new and interesting results.

  15. Information balance in quantum teleportation with an arbitrary pure state

    SciTech Connect

    Li Li; Chen Zengbing

    2005-07-15

    We study a general teleportation scheme with an arbitrary two-party pure state and derive a tight bound of the teleportation fidelity with a predesigned estimation of the unknown state to be teleported. This bound shows a piecewise balance between information gain and state disturbance. We also explain possible physical significance of the balance.

  16. A pure-sampling quantum Monte Carlo algorithm

    NASA Astrophysics Data System (ADS)

    Ospadov, Egor; Rothstein, Stuart M.

    2015-01-01

    The objective of pure-sampling quantum Monte Carlo is to calculate physical properties that are independent of the importance sampling function being employed in the calculation, save for the mismatch of its nodal hypersurface with that of the exact wave function. To achieve this objective, we report a pure-sampling algorithm that combines features of forward walking methods of pure-sampling and reptation quantum Monte Carlo (RQMC). The new algorithm accurately samples properties from the mixed and pure distributions simultaneously in runs performed at a single set of time-steps, over which extrapolation to zero time-step is performed. In a detailed comparison, we found RQMC to be less efficient. It requires different sets of time-steps to accurately determine the energy and other properties, such as the dipole moment. We implement our algorithm by systematically increasing an algorithmic parameter until the properties converge to statistically equivalent values. As a proof in principle, we calculated the fixed-node energy, static α polarizability, and other one-electron expectation values for the ground-states of LiH and water molecules. These quantities are free from importance sampling bias, population control bias, time-step bias, extrapolation-model bias, and the finite-field approximation. We found excellent agreement with the accepted values for the energy and a variety of other properties for those systems.

  17. Enzymatic Synthesis of Single-Stranded Clonal Pure Oligonucleotides.

    PubMed

    Ducani, Cosimo; Högberg, Björn

    2017-01-01

    Single-stranded oligonucleotides, or oligodeoxyribonucleotides (ODNs), are very important in several fields of science such as molecular biology, diagnostics, nanotechnology, and gene therapy. They are usually chemically synthesized. Here we describe an enzymatic method which enables us to synthesize pure oligonucleotides which can be up to several hundred long bases. PMID:27671934

  18. Entropy for quantum pure states and quantum H theorem

    NASA Astrophysics Data System (ADS)

    Han, Xizhi; Wu, Biao

    2015-06-01

    We construct a complete set of Wannier functions that are localized at both given positions and momenta. This allows us to introduce the quantum phase space, onto which a quantum pure state can be mapped unitarily. Using its probability distribution in quantum phase space, we define an entropy for a quantum pure state. We prove an inequality regarding the long-time behavior of our entropy's fluctuation. For a typical initial state, this inequality indicates that our entropy can relax dynamically to a maximized value and stay there most of time with small fluctuations. This result echoes the quantum H theorem proved by von Neumann [Zeitschrift für Physik 57, 30 (1929), 10.1007/BF01339852]. Our entropy is different from the standard von Neumann entropy, which is always zero for quantum pure states. According to our definition, a system always has bigger entropy than its subsystem even when the system is described by a pure state. As the construction of the Wannier basis can be implemented numerically, the dynamical evolution of our entropy is illustrated with an example.

  19. Pure spin current transport in Alq3 by spin pumping

    NASA Astrophysics Data System (ADS)

    Jiang, Shengwei; Wang, Peng; Luan, Zhongzhi; Tao, Xinde; Ding, Haifeng; Wu, Di

    2015-03-01

    The use of organic semiconductors (OSCs) in spintronics has aroused considerable interests, owing to their much longer spin-relaxation times of OSCs than those of inorganic counterparts. The most studied example is the organic spin valve (OSV), in which magnetoresistance (MR) effect is frequently reported. However, studies on pure spin current injection and transport in OSCs are scarce. Recently, the pioneering work by Watanabe et al. demonstrated that pure spin current can be pumped into and propagates in semiconducting polymers. In the present work we extend the study to small molecule OSCs, and demonstrate that pure spin current can be injected into Alq3 from the adjacent magnetic insulator Y3Fe5O12 (YIG) by spin pumping. The pure spin current is detected by inverse spin Hall effect (ISHE) in Pd after propagation through Alq3. From the ISHE voltage VISHE as a function of the Alq3 thickness, the spin diffusion length is determined to be ~ 50 nm and does not depend on temperature. This result indicates the MR decrease as increasing temperature in OSVs is not due to the reduced spin diffusion length.

  20. LOADING MACHINE FOR REACTORS

    DOEpatents

    Simon, S.L.

    1959-07-01

    An apparatus is described for loading or charging slugs of fissionable material into a nuclear reactor. The apparatus of the invention is a "muzzle loading" type comprising a delivery tube or muzzle designed to be brought into alignment with any one of a plurality of fuel channels. The delivery tube is located within the pressure shell and it is also disposed within shielding barriers while the fuel cantridges or slugs are forced through the delivery tube by an externally driven flexible ram.

  1. Load research manual. Volume 3. Load research for advanced technologies

    SciTech Connect

    Brandenburg, L.; Clarkson, G.; Grund, Jr., C.; Leo, J.; Asbury, J.; Brandon-Brown, F.; Derderian, H.; Mueller, R.; Swaroop, R.

    1980-11-01

    This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. The manual includes guides to load research literature and glossaries of load research and statistical terms. In Volume 3, special load research procedures are presented for solar, wind, and cogeneration technologies.

  2. Probabilistic load model development and validation for composite load spectra for select space propulsion engines

    NASA Technical Reports Server (NTRS)

    Kurth, R.; Newell, J. F.

    1987-01-01

    A major task of the program to develop an expert system to predict the loads on selected components of a generic space propulsion engine is the design development and application of a probabilitic loads model. This model is being developed in order to account for the random nature of the loads and assess the variable load ranges' effect on the engine performance. A probabilistic model has been developed. The model is based primarily on simulation methods, but also has a Gaussian algebra method (if all variables are near normal), a fast probability integrator routine (for the calculation of low probability events), and a separate, stand alone program for performing barrier crossing calculations. Each of these probabilistic methods has been verified with theoretical calculations using assumed distributional forms.

  3. Towards multiple hazard resilient bridges: a methodology for modeling frequent and infrequent time-varying loads Part II, Examples for live and earthquake load effects

    NASA Astrophysics Data System (ADS)

    Liang, Zach; Lee, George C.

    2012-09-01

    The current AASHTO load and resistance factor design (LRFD) guidelines are formulated based on bridge reliability, which interprets traditional design safety factors into more rigorously deduced factors based on the theory of probability. This is a major advancement in bridge design specifications. However, LRFD is only calibrated for dead and live loads. In cases when extreme loads are significant, they need to be individually assessed. Combining regular loads with extreme loads has been a major challenge, mainly because the extreme loads are time variable and cannot be directly combined with time invariant loads to formulate the probability of structural failure. To overcome these difficulties, this paper suggests a methodology of comprehensive reliability, by introducing the concept of partial failure probability to separate the loads so that each individual load combination under a certain condition can be approximated as time invariant. Based on these conditions, the extreme loads (also referred to as multiple hazard or MH loads) can be broken down into single effects. In this paper, a further breakdown of these conditional occurrence probabilities into pure conditions is discussed by using a live truck and earthquake loads on a bridge as an example.

  4. Ignition and combustion of bulk metals under elevated, normal and reduced gravity conditions

    NASA Technical Reports Server (NTRS)

    Abbud-Madrid, Angel; Branch, Melvyn C.; Daily, John W.

    1995-01-01

    This research effort is aimed at providing further insight into this multi-variable dependent phenomena by looking at the effects of gravity on the ignition and combustion behavior of metals. Since spacecraft are subjected to higher-than-1g gravity loads during launch and reentry and to zero-gravity environments while in orbit, the study of ignition and combustion of bulk metals at different gravitational potentials is of great practical concern. From the scientific standpoint, studies conducted under microgravity conditions provide simplified boundary conditions since buoyancy is removed, and make possible the identification of fundamental ignition mechanisms. The effect of microgravity on the combustion of bulk metals has been investigated by Steinberg, et al. on a drop tower simulator. However, no detailed quantitative work has been done on ignition phenomena of bulk metals at lower or higher-than-normal gravitational fields or on the combustion characteristics of metals at elevated gravity. The primary objective of this investigation is the development of an experimental system capable of providing fundamental physical and chemical information on the ignition of bulk metals under different gravity levels. The metals used in the study, iron (Fe), titanium (Ti), zirconium (Zr), magnesium (Mg), zinc (Zn), and copper (Cu) were selected because of their importance as elements of structural metals and their simple chemical composition (pure metals instead of multi-component alloys to avoid complication in morphology and spectroscopic studies). These samples were also chosen to study the two different combustion modes experienced by metals: heterogeneous or surface oxidation, and homogeneous or gas-phase reaction. The experimental approach provides surface temperature profiles, spectroscopic measurements, surface morphology, x-ray spectrometry of metals specimens and their combustion products, and high-speed cinematography of the heating, ignition and combustion

  5. Short term load forecasting of anomalous load using hybrid soft computing methods

    NASA Astrophysics Data System (ADS)

    Rasyid, S. A.; Abdullah, A. G.; Mulyadi, Y.

    2016-04-01

    Load forecast accuracy will have an impact on the generation cost is more economical. The use of electrical energy by consumers on holiday, show the tendency of the load patterns are not identical, it is different from the pattern of the load on a normal day. It is then defined as a anomalous load. In this paper, the method of hybrid ANN-Particle Swarm proposed to improve the accuracy of anomalous load forecasting that often occur on holidays. The proposed methodology has been used to forecast the half-hourly electricity demand for power systems in the Indonesia National Electricity Market in West Java region. Experiments were conducted by testing various of learning rate and learning data input. Performance of this methodology will be validated with real data from the national of electricity company. The result of observations show that the proposed formula is very effective to short-term load forecasting in the case of anomalous load. Hybrid ANN-Swarm Particle relatively simple and easy as a analysis tool by engineers.

  6. Pure and Pseudo-pure Fluid Thermophysical Property Evaluation and the Open-Source Thermophysical Property Library CoolProp

    PubMed Central

    2014-01-01

    Over the last few decades, researchers have developed a number of empirical and theoretical models for the correlation and prediction of the thermophysical properties of pure fluids and mixtures treated as pseudo-pure fluids. In this paper, a survey of all the state-of-the-art formulations of thermophysical properties is presented. The most-accurate thermodynamic properties are obtained from multiparameter Helmholtz-energy-explicit-type formulations. For the transport properties, a wider range of methods has been employed, including the extended corresponding states method. All of the thermophysical property correlations described here have been implemented into CoolProp, an open-source thermophysical property library. This library is written in C++, with wrappers available for the majority of programming languages and platforms of technical interest. As of publication, 110 pure and pseudo-pure fluids are included in the library, as well as properties of 40 incompressible fluids and humid air. The source code for the CoolProp library is included as an electronic annex. PMID:24623957

  7. Composite fracture using the normal stress ratio theory

    NASA Technical Reports Server (NTRS)

    Beuth, J. L., Jr.; Gurdal, Z.; Herakovich, C. T.

    1989-01-01

    Experiments were performed on center-notched specimens of unidirectional AS4/3501-6 graphite-epoxy subjected to varied far-field loading conditions. Specimens tested include on-axis and off-axis tensile coupons and Iosipescu shear specimens, allowing the study of normal, shear, and combined far-field loading conditions. From the tests, the direction of initial crack extension and the far-field stresses at crack initiation and fracture are obtained. The normal stress ratio theory is subsequently applied within a macroscopic-level homogeneous anisotropic stress solution to predict the direction of crack extension, critical stresses, and other crack growth behavior for the experiments. Comparison between experimental results and theoretical predictions indicates that application of the normal stress ratio theory within a macroscopic-level stress analysis has significant potential as an approach to modeling composite crack growth.

  8. Experimental Observations of a Stitched Composite with a Notch Subjected to Combined Bending and Tension Loading

    NASA Technical Reports Server (NTRS)

    Palmer, Susan O.; Nettles, Alan T.; Poe, C. C.

    1998-01-01

    A series of tests was conducted to support development of an analytical model for predicting the failure strains of stitched warp-knit carbon/epoxy composite materials with through-thicknesss damage in the form of a crack-like notch. Measurements of strain near notch tips, crack opening displacement (COD), and applied load were monitored in all tests. The out-of-plane displacement at the center of the notch was also measured when the specimen was subjected to bending. Three types of loading were applied: pure bending, pure tension, and combined bending and tension.

  9. WMAP normalization of inflationary cosmologies

    SciTech Connect

    Liddle, Andrew R.; Parkinson, David; Mukherjee, Pia; Leach, Samuel M.

    2006-10-15

    We use the three-year WMAP observations to determine the normalization of the matter power spectrum in inflationary cosmologies. In this context, the quantity of interest is not the normalization marginalized over all parameters, but rather the normalization as a function of the inflationary parameters n{sub S} and r with marginalization over the remaining cosmological parameters. We compute this normalization and provide an accurate fitting function. The statistical uncertainty in the normalization is 3%, roughly half that achieved by COBE. We use the k-l relation for the standard cosmological model to identify the pivot scale for the WMAP normalization. We also quote the inflationary energy scale corresponding to the WMAP normalization.

  10. Working Memory Load Attenuates Emotional Enhancement in Recognition Memory

    PubMed Central

    Miendlarzewska, Ewa A.; van Elswijk, Gijs; Cannistraci, Carlo V.; van Ee, Raymond

    2013-01-01

    Emotionally arousing stimuli are perceived and remembered better than neutral stimuli. Under threat, this negativity bias is further increased. We investigated whether working memory (WM) load can attenuate incidental memory for emotional images. Two groups of participants performed the N-back task with two WM load levels. In one group, we induced anxiety using a threat of shock paradigm to increase attentional processing of negative information. During task performance we incidentally and briefly flashed emotional distracter images which prolonged response times in both load conditions. A subsequent unannounced immediate recognition memory test revealed that when load at exposure had been low, recognition was better for negative items in both participant groups. This enhancement, however, was attenuated under high load, leaving performance on neutral items unchanged regardless of the threat of shock manipulation. We conclude that both in threat and in normal states WM load at exposure can attenuate immediate emotional memory enhancement. PMID:23515565

  11. Pure odd-order oscillators with constant excitation

    NASA Astrophysics Data System (ADS)

    Cveticanin, L.

    2011-02-01

    In this paper the excited vibrations of a truly nonlinear oscillator are analyzed. The excitation is assumed to be constant and the nonlinearity is pure (without a linear term). The mathematical model is a second-order nonhomogeneous differential equation with strong nonlinear term. Using the first integral, the exact value of period of vibration i.e., angular frequency of oscillator described with a pure nonlinear differential equation with constant excitation is analytically obtained. The closed form solution has the form of gamma function. The period of vibration depends on the value of excitation and of the order and coefficient of the nonlinear term. For the case of pure odd-order-oscillators the approximate solution of differential equation is obtained in the form of trigonometric function. The solution is based on the exact value of period of vibration. For the case when additional small perturbation of the pure oscillator acts, the so called 'Cveticanin's averaging method' for a truly nonlinear oscillator is applied. Two special cases are considered: one, when the additional term is a function of distance, and the second, when damping acts. To prove the correctness of the method the obtained results are compared with those for the linear oscillator. Example of pure cubic oscillator with constant excitation and linear damping is widely discussed. Comparing the analytically obtained results with exact numerical ones it is concluded that they are in a good agreement. The investigations reported in the paper are of special interest for those who are dealing with the problem of vibration reduction in the oscillator with constant excitation and pure nonlinear restoring force the examples of which can be found in various scientific and engineering systems. For example, such mechanical systems are seats in vehicles, supports for machines, cutting machines with periodical motion of the cutting tools, presses, etc. The examples can be find in electronics

  12. Beer and wine but not whisky and pure ethanol do stimulate release of gastrin in humans.

    PubMed

    Singer, M V; Eysselein, V; Goebell, H

    1983-01-01

    In humans, the action of ethanol on gastrin release is still unclear and that of alcoholic beverages greatly unknown. We studied the effect of a drink of various concentrations of pure ethanol and several commonly ingested alcoholic beverages on plasma levels of immunoreactive gastrin in 6 healthy human volunteers and compared the results to a protein-rich meal. A drink of distilled water (250 ml) and of pure ethanol (250 ml or 125 ml in the case of 40% v/v ethanol) in concentrations (4, 10, 20 and 40% v/v) normally present in beer, wine, liquor and whisky did not stimulate plasma gastrin levels above basal. Of the alcoholic beverages given only whisky (125 ml) did not stimulate gastrin release. Beer, red and white wine (250 ml each) caused a rapid increase in plasma gastrin concentrations with a peak at 15-20 min, basal levels being reached 60 min after starting the drink. The 60-min integrated plasma gastrin response to beer, red and white wine was about 50% of the gastrin response to the protein-rich (steak) meal (883 +/- 297 pmol X min X 1(-1); mean +/- SE). A drink of 250 ml of white wine together with the meal did not cause a significantly higher integrated gastrin response than the protein meal with 250 ml of distilled water. We conclude that commonly ingested alcoholic beverages such as beer, red and white wine, but not whisky, are potent stimulants of gastrin release in humans. The ethanol content of these beverages cannot be responsible for the increase in plasma gastrin levels, since oral ingestion of pure ethanol in equivalent concentrations and amounts did not elicit a rise in plasma gastrin levels. Some unknown ingredients present in beer and wine are most likely responsible for the gastrin release by both alcoholic beverages.

  13. A load factor formula

    NASA Technical Reports Server (NTRS)

    Miller, Roy G

    1927-01-01

    The ultimate test of a load factor formula is experience. The chief advantages of a semi rational formula over arbitrary factors are that it fairs in between points of experience and it differentiates according to variables within a type. Structural failure of an airplane apparently safe according to the formula would call for a specific change in the formula. The best class of airplanes with which to check a load factor formula seems to be those which have experienced structural failure. Table I comprises a list of the airplanes which have experienced failure in flight traceable to the wing structure. The load factor by formula is observed to be greater than the designed strength in each case, without a single exception. Table II comprises the load factor by formula with the designed strength of a number of well-known service types. The formula indicates that by far the majority of these have ample structural strength. One case considered here in deriving a suitable formula is that of a heavy load carrier of large size and practically no reserve power.

  14. Class III β-tubulin in normal and cancer tissues.

    PubMed

    Mariani, Marisa; Karki, Roshan; Spennato, Manuela; Pandya, Deep; He, Shiquan; Andreoli, Mirko; Fiedler, Paul; Ferlini, Cristiano

    2015-06-01

    Microtubules are polymeric structures composed of tubulin subunits. Each subunit consists of a heterodimer of α- and β-tubulin. At least seven β-tubulin isotypes, or classes, have been identified in human cells, and constitutive isotype expression appears to be tissue specific. Class III β-tubulin (βIII-tubulin) expression is normally confined to testes and tissues derived from neural cristae. However, its expression can be induced in other tissues, both normal and neoplastic, subjected to a toxic microenvironment characterized by hypoxia and poor nutrient supply. In this review, we will summarize the mechanisms underlying βIII-tubulin constitutive and induced expression. We will also illustrate its capacity to serve as a biomarker of neural commitment in normal tissues and as a pure prognostic biomarker in cancer patients.

  15. Pure word deafness with auditory object agnosia after bilateral lesion of the superior temporal sulcus.

    PubMed

    Gutschalk, Alexander; Uppenkamp, Stefan; Riedel, Bernhard; Bartsch, Andreas; Brandt, Tobias; Vogt-Schaden, Marlies

    2015-12-01

    Based on results from functional imaging, cortex along the superior temporal sulcus (STS) has been suggested to subserve phoneme and pre-lexical speech perception. For vowel classification, both superior temporal plane (STP) and STS areas have been suggested relevant. Lesion of bilateral STS may conversely be expected to cause pure word deafness and possibly also impaired vowel classification. Here we studied a patient with bilateral STS lesions caused by ischemic strokes and relatively intact medial STPs to characterize the behavioral consequences of STS loss. The patient showed severe deficits in auditory speech perception, whereas his speech production was fluent and communication by written speech was grossly intact. Auditory-evoked fields in the STP were within normal limits on both sides, suggesting that major parts of the auditory cortex were functionally intact. Further studies showed that the patient had normal hearing thresholds and only mild disability in tests for telencephalic hearing disorder. Prominent deficits were discovered in an auditory-object classification task, where the patient performed four standard deviations below the control group. In marked contrast, performance in a vowel-classification task was intact. Auditory evoked fields showed enhanced responses for vowels compared to matched non-vowels within normal limits. Our results are consistent with the notion that cortex along STS is important for auditory speech perception, although it does not appear to be entirely speech specific. Formant analysis and single vowel classification, however, appear to be already implemented in auditory cortex on the STP.

  16. An Experimental Study of a Stitched Composite with a Notch Subjected to Combined Bending and Tension Loading

    NASA Technical Reports Server (NTRS)

    Palmer, Susan O.; Nettles, Alan T.; Poe, C. C., Jr.

    1999-01-01

    A series of tests was conducted to measure the strength of stitched carbon/epoxy composites containing through-thickness damage in the form of a crack-like notch. The specimens were subjected to three types of loading: pure bending, pure tension, and combined bending and tension loads. Measurements of applied loads, strains near crack tips, and crack opening displacements (COD) were monitored in all tests. The transverse displacement at the center of the specimen was measured using a Linear Variable Differential Transformer (LVDT). The experimental data showed that the outer surface of the pure tension specimen failed at approximately 6,000 microstrain, while in combined bending and tension loads the measured tensile strains reached 10,000 microstrain.

  17. Buckling behavior of long anisotropic plates subjected to combined loads

    NASA Technical Reports Server (NTRS)

    Nemeth, Michael P.

    1995-01-01

    A parametric study is presented of the buckling behavior of infinitely long symmetrically laminated anisotropic plates subjected to combined loads. The study focuses on the interaction of a subcritical (stable) secondary loading state of constant magnitude and a primary destabilizing load that is increased in magnitude until buckling occurs. The loads, considered in this report are uniform axial compression, pure in-plane bending, transverse tension and compression, and shear. Results are presented that were obtained by using a special purpose nondimensional analysis that is well suited for parametric studies of clamped and simply supported plates. In particular, results are presented for a +/- 45(sub S) graphite-epoxy laminate that is highly anisotropic and representative of a laminate used for spacecraft applications. In addition, generic buckling-design charts are presented for a wide range of nondimensional parameters that are applicable to a broad class of laminate constructions. These results show the general behavioral trends of specially orthotropic plates and the effects of flexural anisotropy on plates subjected to various combined loading conditions. An important finding of the present study is that the effects of flexural anisotropy on the buckling resistance of a plate can be significantly more important for plates subjected to combined loads than for plates subjected to single-component loads.

  18. Gas loading apparatus for the Paris-Edinburgh press

    SciTech Connect

    Bocian, A.; Kamenev, K. V.; Bull, C. L.; Hamidov, H.; Loveday, J. S.; Nelmes, R. J.

    2010-09-15

    We describe the design and operation of an apparatus for loading gases into the sample volume of the Paris-Edinburgh press at room temperature and high pressure. The system can be used for studies of samples loaded as pure or mixed gases as well as for loading gases as pressure-transmitting media in neutron-scattering experiments. The apparatus consists of a high-pressure vessel and an anvil holder with a clamp mechanism. The vessel, designed to operate at gas pressures of up to 150 MPa, is used for applying the load onto the anvils located inside the clamp. This initial load is sufficient for sealing the pressurized gas inside the sample containing gasket. The clamp containing the anvils and the sample is then transferred into the Paris-Edinburgh press by which further load can be applied to the sample. The clamp has apertures for scattered neutron beams and remains in the press for the duration of the experiment. The performance of the gas loading system is illustrated with the results of neutron-diffraction experiments on compressed nitrogen.

  19. E-2C Loads Calibration in DFRC Flight Loads Lab

    NASA Technical Reports Server (NTRS)

    Schuster, Lawrence S.

    2008-01-01

    Objectives: a) Safely and efficiently perform structural load tests on NAVAIR E-2C aircraft to calibrate strain gage instrumentation installed by NAVAIR; b) Collect load test data and derive loads equations for use in NAVAIR flight tests; and c) Assist flight test team with use of loads equations measurements at PAX River.

  20. Fruit load governs transpiration of olive trees.

    PubMed

    Bustan, Amnon; Dag, Arnon; Yermiyahu, Uri; Erel, Ran; Presnov, Eugene; Agam, Nurit; Kool, Dilia; Iwema, Joost; Zipori, Isaac; Ben-Gal, Alon

    2016-03-01

    We tested the hypothesis that whole-tree water consumption of olives (Olea europaea L.) is fruit load-dependent and investigated the driving physiological mechanisms. Fruit load was manipulated in mature olives grown in weighing-drainage lysimeters. Fruit was thinned or entirely removed from trees at three separate stages of growth: early, mid and late in the season. Tree-scale transpiration, calculated from lysimeter water balance, was found to be a function of fruit load, canopy size and weather conditions. Fruit removal caused an immediate decline in water consumption, measured as whole-plant transpiration normalized to tree size, which persisted until the end of the season. The later the execution of fruit removal, the greater was the response. The amount of water transpired by a fruit-loaded tree was found to be roughly 30% greater than that of an equivalent low- or nonyielding tree. The tree-scale response to fruit was reflected in stem water potential but was not mirrored in leaf-scale physiological measurements of stomatal conductance or photosynthesis. Trees with low or no fruit load had higher vegetative growth rates. However, no significant difference was observed in the overall aboveground dry biomass among groups, when fruit was included. This case, where carbon sources and sinks were both not limiting, suggests that the role of fruit on water consumption involves signaling and alterations in hydraulic properties of vascular tissues and tree organs.

  1. Secondary pure erythroid leukaemia in relapsed acute lymphoblastic leukaemia: lineage switch or chemotherapy effect?

    PubMed

    Gupta, Sanjeev Kumar; Kumar, Rajive; Chharchhodawala, Taher; Kumar, Lalit

    2014-05-19

    Pure erythroid leukaemia is a rare subtype of acute myeloid leukaemia (AML) and its occurrence at acute lymphoblastic leukaemia (ALL) relapse has not been reported earlier. A 39-year-old man received chemotherapy for Philadelphia-negative B cell ALL. Subsequently, he developed pure erythroid leukaemia with >80% immature erythroid precursors in bone marrow showing block positivity on periodic acid-Schiff stain, expressing CD71, CD34 but lacking CD235a. The interval between exposure to multidrug chemotherapy including cyclophosphamide and AML diagnosis was 2 years and 9 months. No cytogenetic abnormality was detected at the time of relapse. The patient died 2 weeks after starting AML chemotherapy. The relatively narrow time interval (usually 5-10 years) between chemotherapy and AML development and normal karyotype at relapse raises a possibility of lineage switch besides therapy-related AML as the likely pathogenesis. Further exploration of such cases may unravel the pathways responsible for lineage assignment in pluripotent stem cells.

  2. Pure valley- and spin-entangled states in a MoS2-based bipolar transistor

    NASA Astrophysics Data System (ADS)

    Bai, Chunxu; Zou, Yonglian; Lou, Wen-Kai; Chang, Kai

    2014-11-01

    In this study, we show that the local Andreev reflection not only can be tuned largely by the type of the normal metal electrode, it also is related to the electrostatic potential in the superconductor region in a MoS2-based n (p ) -type metal/superconductor junction. In a MoS2-based n -type metal/n (p ) -type superconductor/p -type metal (n Sp ) transistor, nonlocal pure valley- and spin-entangled current can be tuned by the length and local gate voltage of a superconductor region. In particular, switching the quasiparticle type in both structures results in a series of intriguing features. Such an effect is not attainable in a graphene-based junction where the electron-hole symmetry enables the symmetry results to be observed. Besides, we have shown that the crossed Andreev reflection exhibits a maximum around ξ /2 instead of the exponential decay behavior in conventional superconductors and a maximum around ξ in the graphene material. The proposed straightforward experimental design and pure valley- and spin-entangled state can pave the way for a wider use in the entanglement based on material group-VI dichalcogenides.

  3. Raman spectroscopy analysis of air grown oxide scale developed on pure zirconium substrate

    NASA Astrophysics Data System (ADS)

    Kurpaska, L.; Favergeon, J.; Lahoche, L.; El-Marssi, M.; Grosseau Poussard, J.-L.; Moulin, G.; Roelandt, J.-M.

    2015-11-01

    Using Raman spectroscopy technique, external and internal parts of zirconia oxide films developed at 500 °C and 600 °C on pure zirconium substrate under air at normal atmospheric pressure have been examined. Comparison of Raman peak positions of tetragonal and monoclinic zirconia phases, recorded during the oxide growth at elevated temperature, and after cooling at room temperature have been presented. Subsequently, Raman peak positions (or shifts) were interpreted in relation with the stress evolution in the growing zirconia scale, especially closed to the metal/oxide interface, where the influence of compressive stress in the oxide is the biggest. Reported results, for the first time show the presence of a continuous layer of tetragonal zirconia phase developed in the proximity of pure zirconium substrate. Based on the Raman peak positions we prove that this tetragonal layer is stabilized by the high compressive stress and sub-stoichiometry level. Presence of the tetragonal phase located in the outer part of the scale have been confirmed, yet its Raman characteristics suggest a stress-free tetragonal phase, therefore different type of stabilization mechanism. Presented study suggest that its stabilization could be related to the lattice defects introduced by highstoichiometry of zirconia or presence of heterovalent cations.

  4. Partially degradable friction-welded pure iron-stainless steel 316L bone pin.

    PubMed

    Nasution, A K; Murni, N S; Sing, N B; Idris, M H; Hermawan, H

    2015-01-01

    This article describes the development of a partially degradable metal bone pin, proposed to minimize the occurrence of bone refracture by avoiding the creation of holes in the bone after pin removal procedure. The pin was made by friction welding and composed of two parts: the degradable part that remains in the bone and the nondegradable part that will be removed as usual. Rods of stainless steel 316L (nondegradable) and pure iron (degradable) were friction welded at the optimum parameters: forging pressure = 33.2 kPa, friction time = 25 s, burn-off length = 15 mm, and heat input = 4.58 J/s. The optimum tensile strength and elongation was registered at 666 MPa and 13%, respectively. A spiral defect formation was identified as the cause for the ductile fracture of the weld joint. A 40-µm wide intermetallic zone was identified along the fusion line having a distinct composition of Cr, Ni, and Mo. The corrosion rate of the pin gradually decreased from the undeformed zone of pure iron to the undeformed zone of stainless steel 316L. All metallurgical zones of the pin showed no toxic effect toward normal human osteoblast cells, confirming the ppb level of released Cr and Ni detected in the cell media were tolerable.

  5. Shuttle car loading system

    NASA Technical Reports Server (NTRS)

    Collins, E. R., Jr. (Inventor)

    1985-01-01

    A system is described for loading newly mined material such as coal, into a shuttle car, at a location near the mine face where there is only a limited height available for a loading system. The system includes a storage bin having several telescoping bin sections and a shuttle car having a bottom wall that can move under the bin. With the bin in an extended position and filled with coal the bin sections can be telescoped to allow the coal to drop out of the bin sections and into the shuttle car, to quickly load the car. The bin sections can then be extended, so they can be slowly filled with more while waiting another shuttle car.

  6. Microbial load monitor

    NASA Technical Reports Server (NTRS)

    Caplin, R. S.; Royer, E. R.

    1978-01-01

    Attempts are made to provide a total design of a Microbial Load Monitor (MLM) system flight engineering model. Activities include assembly and testing of Sample Receiving and Card Loading Devices (SRCLDs), operator related software, and testing of biological samples in the MLM. Progress was made in assembling SRCLDs with minimal leaks and which operate reliably in the Sample Loading System. Seven operator commands are used to control various aspects of the MLM such as calibrating and reading the incubating reading head, setting the clock and reading time, and status of Card. Testing of the instrument, both in hardware and biologically, was performed. Hardware testing concentrated on SRCLDs. Biological testing covered 66 clinical and seeded samples. Tentative thresholds were set and media performance listed.

  7. [Clinical picture of pure corneal ulcers of different localizations].

    PubMed

    Tarasova, L N; Kudriashova, Iu I

    1999-01-01

    Pure corneal ulcers can be localized at the periphery and in the center. Peripheral ulcers are bilateral in 66% and multifocal in 48% cases. They are combined with local vasculitis of perilimbic vessels of the conjunctiva. In 84% cases the disease occurred in patients with connective tissue and articular diseases. Clinical picture of the peripheral corneal ulcer differs from Mourene's phagodenic ulcer. Central corneal ulcers are bilateral in 40% patients, are associated with primary and secondary "dry eye" syndrome in Sjogren's disease, rheumatoid arthritis, systemic vasculitis, Behçet's disease, and in 18% patients with cicatricial deformation of the conjunctiva after Stevens-Johnson's syndrome, trachoma, and chemical burns of the eyes. Pure corneal ulcers run a chronic relapsing course, complicated in one-fourth of patients by corneal perforation and secondary infections.

  8. Biomedical effects of mushrooms with emphasis on pure compounds.

    PubMed

    Paterson, R Russell M; Lima, Nelson

    2014-01-01

    Medicinal mushrooms show great promise for disease treatments. They have been employed in the Orient and Occident for thousands of years, although the practice has persisted in the East. They remain highly valuable. Authentic human trials and pure compounds are emphasized in this review of the most current literature. Polysaccharides from the fungi appear effective in cancer treatments and low-molecular-weight compounds also attract much interest. However, reports of toxicity must be taken seriously. Prescriptions for mushrooms and preparations need to be given by qualified medical practitioners. The reason why these preparations are not more widely used in the West is related to problems of (A) intellectual property rights, (B) mass production, and (C) obtaining pure compounds that retain activity. Mushroom compounds require testing against infectious diseases such as those caused by bacteria, because the current antibiotics are failing from resistances. Overall, the future is assured for medicinal mushrooms.

  9. New Formulation of Statistical Mechanics Using Thermal Pure Quantum States

    NASA Astrophysics Data System (ADS)

    Sugiura, Sho; Shimizu, Akira

    2014-03-01

    We formulate statistical mechanics based on a pure quantum state, which we call a "thermal pure quantum (TPQ) state". A single TPQ state gives not only equilibrium values of mechanical variables, such as magnetization and correlation functions, but also those of genuine thermodynamic variables and thermodynamic functions, such as entropy and free energy. Among many possible TPQ states, we discuss the canonical TPQ state, the TPQ state whose temperature is specified. In the TPQ formulation of statistical mechanics, thermal fluctuations are completely included in quantum-mechanical fluctuations. As a consequence, TPQ states have much larger quantum entanglement than the equilibrium density operators of the ensemble formulation. We also show that the TPQ formulation is very useful in practical computations, by applying the formulation to a frustrated two-dimensional quantum spin system.

  10. Synthesis and photoluminescence of ultra-pure germanium nanoparticles

    NASA Astrophysics Data System (ADS)

    Chivas, R.; Yerci, S.; Li, R.; Dal Negro, L.; Morse, T. F.

    2011-09-01

    We have used aerosol deposition to synthesize defect and micro-strain free, ultra-pure germanium nanoparticles. Transmission electron microscopy images show a core-shell configuration with highly crystalline core material. Powder X-ray diffraction measurements verify the presence of highly pure, nano-scale germanium with average crystallite size of 30 nm and micro-strain of 0.058%. X-ray photoelectron spectroscopy demonstrates that GeO x ( x ⩽ 2) shells cover the surfaces of the nanoparticles. Under optical excitation, these nanoparticles exhibit two separate emission bands at room temperature: a visible emission at 500 nm with 0.5-1 ns decay times and an intense near-infrared emission at 1575 nm with up to ˜20 μs lifetime.

  11. Control aspects of quantum computing using pure and mixed states.

    PubMed

    Schulte-Herbrüggen, Thomas; Marx, Raimund; Fahmy, Amr; Kauffman, Louis; Lomonaco, Samuel; Khaneja, Navin; Glaser, Steffen J

    2012-10-13

    Steering quantum dynamics such that the target states solve classically hard problems is paramount to quantum simulation and computation. And beyond, quantum control is also essential to pave the way to quantum technologies. Here, important control techniques are reviewed and presented in a unified frame covering quantum computational gate synthesis and spectroscopic state transfer alike. We emphasize that it does not matter whether the quantum states of interest are pure or not. While pure states underly the design of quantum circuits, ensemble mixtures of quantum states can be exploited in a more recent class of algorithms: it is illustrated by characterizing the Jones polynomial in order to distinguish between different (classes of) knots. Further applications include Josephson elements, cavity grids, ion traps and nitrogen vacancy centres in scenarios of closed as well as open quantum systems.

  12. Modeling pure culture heterotrophic production of polyhydroxybutyrate (PHB).

    PubMed

    Mozumder, Md Salatul Islam; Goormachtigh, Laurens; Garcia-Gonzalez, Linsey; De Wever, Heleen; Volcke, Eveline I P

    2014-03-01

    In this contribution a mechanistic model describing the production of polyhydroxybutyrate (PHB) through pure-culture fermentation was developed, calibrated and validated for two different substrates, namely glucose and waste glycerol. In both cases, non-growth-associated PHB production was triggered by applying nitrogen limitation. The occurrence of some growth-associated PHB production besides non-growth-associated PHB production was demonstrated, although it is inhibited in the presence of nitrogen. Other phenomena observed experimentally and described by the model included biomass growth on PHB and non-linear product inhibition of PHB production. The accumulated impurities from the waste substrate negatively affected the obtained maximum PHB content. Overall, the developed mathematical model provided an accurate prediction of the dynamic behavior of heterotrophic biomass growth and PHB production in a two-phase pure culture system. PMID:24457311

  13. The formation of blobs from a pure interchange process

    SciTech Connect

    Zhu, P.; Sovinec, C. R.; Hegna, C. C.

    2015-02-15

    In this work, we focus on examining a pure interchange process in a shear-less slab configuration as a prototype mechanism for blob formation. We employ full magnetohydrodynamic simulations to demonstrate that the blob-like structures can emerge through the nonlinear development of a pure interchange instability originating from a pedestal-like transition region. In the early nonlinear stage, filamentary structures develop and extend in the direction of the effective gravity. The blob-like structures appear when the radially extending filaments break off and disconnect from the core plasma. The morphology and the dynamics of these filaments and blobs vary dramatically with a sensitive dependence on the dissipation mechanisms in the system and the initial perturbation. Despite the complexity in morphology and dynamics, the nature of the entire blob formation process in the shear-less slab configuration remains strictly interchange without involving any change in magnetic topology.

  14. Assessment of semen quality in pure and crossbred Jersey bulls

    PubMed Central

    Kumar, Umesh; Gawande, Ajay P.; Sahatpure, Sunil K.; Patil, Manoj S.; Lakde, Chetan K.; Bonde, Sachin W.; Borkar, Pradnyankur L.; Poharkar, Ajay J.; Ramteke, Baldeo R.

    2015-01-01

    Aim: To compare the seminal attributes of neat, pre-freeze (at equilibration), and post-freeze (24 h after freezing) semen in pure and crossbred Jersey bulls. Materials and Methods: Total 36 ejaculates (3 ejaculates from each bull) were collected from 6 pure Jersey and 6 crossbred Jersey bulls and evaluated for various seminal attributes during neat, pre-freeze, and post-freeze semen. Results: The mean (±standard error [SE]) values of neat semen characteristics in pure and crossbred Jersey bulls were recorded such as volume (ml), color, consistency, mass activity (scale: 0-5), and sperm concentration (millions/ml). The extended semen was further investigated at pre-freeze and post-freeze stages and the mean (±SE) values recorded at neat, pre-freeze, and post-freeze semen were compared between pure and crossbred Jersey bulls; sperm motility (80.55±1.70%, 62.77±1.35%, 46.11±1.43% vs. 80.00±1.80%, 65.00±1.66%, 47.22±1.08%), live sperm count (83.63±1.08%, 71.72±1.09%, 58.67±1.02% vs. 80.00±1.08%, 67.91±1.20%, 51.63±0.97%), total abnormal sperm count (8.38±0.32%, 12.30±0.39%, 16.75±0.42% vs. 9.00±0.45%, 12.19±0.48%, 18.11±0.64%), hypo-osmotic swelling (HOS) reacted spermatozoa (71.88±0.77%, 62.05±0.80%, 47.27±1.05% vs. 72.77±1.02%, 62.11±0.89%, 45.94±1.33%), acrosome integrity (89.05±0.83%, 81.33±0.71%, 71.94±0.86% vs. 86.55±0.57%, 78.66±0.42%, 69.38±0.53%), and DNA integrity (99.88±0.07%, 100, 99.66±0.11% vs. 99.94±0.05%, 100, 99.44±0.18%,). The volume, color, consistency, sperm concentration, and initial motility in pure and crossbred Jersey bulls did not differ significantly (p>0.05). The mass activity was significantly (p<0.05) higher in pure Jersey as compare to crossbred Jersey bulls. Live sperm percentage and acrosome integrity was significantly (p<0.01) higher in pure Jersey bulls as compared to crossbred Jersey bulls. However, no statistical difference (p>0.05) was observed in abnormal sperm; HOS reacted spermatozoa and DNA

  15. Structure and properties of rapidly solidified pure tin

    NASA Astrophysics Data System (ADS)

    El-Ashram, T.

    2006-03-01

    A comparison has been made between rapidly solidified (RS) pure Sn using melt-spinning technique and Sn produced by conventional casting, using X-ray diffraction (XRD) analysis, differential thermal analysis (DTA), temperature dependence of resistivity (TDR), density measurement and the dynamical resonance method (DRM) for measuring Young's modulus and internal friction. From the XRD and density measurement, it is found that high concentration of vacancies is present in pure Sn RS, the vacancy concentration is found to be 7x10(-3) . From the DTA measurements, we know that there is an increase in the thermodynamic functions such as enthalpy (Delta H), entropy (Delta S) and free energy (Delta G), and also, there is a decrease in the melting temperature. From the TDR results it follows that the resistivity at room temperature is increased and the temperature coefficient of resistivity is decreased. Finally, DRM results show that Young's modulus is decreased and the internal friction is increased.

  16. Control aspects of quantum computing using pure and mixed states

    PubMed Central

    Schulte-Herbrüggen, Thomas; Marx, Raimund; Fahmy, Amr; Kauffman, Louis; Lomonaco, Samuel; Khaneja, Navin; Glaser, Steffen J.

    2012-01-01

    Steering quantum dynamics such that the target states solve classically hard problems is paramount to quantum simulation and computation. And beyond, quantum control is also essential to pave the way to quantum technologies. Here, important control techniques are reviewed and presented in a unified frame covering quantum computational gate synthesis and spectroscopic state transfer alike. We emphasize that it does not matter whether the quantum states of interest are pure or not. While pure states underly the design of quantum circuits, ensemble mixtures of quantum states can be exploited in a more recent class of algorithms: it is illustrated by characterizing the Jones polynomial in order to distinguish between different (classes of) knots. Further applications include Josephson elements, cavity grids, ion traps and nitrogen vacancy centres in scenarios of closed as well as open quantum systems. PMID:22946034

  17. The value of mortality risk reductions. Pure altruism - a confounder?

    PubMed

    Gyrd-Hansen, Dorte; Kjær, Trine; Seested Nielsen, Jytte

    2016-09-01

    This paper examines public valuations of mortality risk reductions. We set up a theoretical framework that allows for altruistic preferences, and subsequently test theoretical predictions through the design of a discrete choice experiment. By varying the tax scenario (uniform versus individual tax), the experimental design allows us to verify whether pure altruistic preferences are present and the underlying causes. We find evidence of negative pure altruism. Under a coercive uniform tax system respondents lower their willingness to pay possibly to ensure that they are not forcing others to pay at a level that corresponds to their own - higher - valuations. This hypothesis is supported by the observation that respondents perceive other individuals' valuations to be lower than their own. Our results suggest that public valuations of mortality risk reductions may underestimate the true societal value because respondents are considering other individuals' welfare, and wrongfully perceive other people's valuations to be low. PMID:27494571

  18. Carboranylphosphinic Acids: A New Class of Purely Inorganic Ligands.

    PubMed

    Oleshkevich, Elena; Teixidor, Francesc; Choquesillo-Lazarte, Duane; Sillanpää, Reijo; Viñas, Clara

    2016-03-01

    Purely inorganic carboranyl phosphinates were prepared, and the influence of the cluster on the reactivity of the phosphinate group was studied. Electron-withdrawal by the carboranyl carbon atoms, combined with space-filling efficiency and enhanced aromaticity of the cluster cage, renders the phosphorus more difficult to oxidize. This enables carboranyl phosphinates to survive harsh oxidizing conditions, a property which is uncommon in organic phosphinates. PMID:26638876

  19. Pure versus hybrid: performance implications of Porter's generic strategies.

    PubMed

    Kumar, K; Subramanian, R; Yauger, C

    1997-01-01

    This article identifies the strategic types in the hospital industry based on the hospital's use of Porter's generic strategies in their pure and hybrid forms. The article also examines differences in performance of hospitals across strategic types. Results indicate that hospitals that follow a focussed cost leadership strategy, in general, have superior performance on a variety of performance measures, while hospitals that use a combination of cost leadership and differentiation perform the poorest. Implications of findings for hospital administrators are also discussed.

  20. Pure Lovelock gravity and Chern-Simons theory

    NASA Astrophysics Data System (ADS)

    Concha, P. K.; Durka, R.; Inostroza, C.; Merino, N.; Rodríguez, E. K.

    2016-07-01

    We explore the possibility of finding pure Lovelock gravity as a particular limit of a Chern-Simons action for a specific expansion of the AdS algebra in odd dimensions. We derive in detail this relation at the level of the action in five and seven dimensions. We provide a general result for higher dimensions and discuss some issues arising from the obtained dynamics.