Interface Design Description for the Multi-Mode Magnetic Detection System

DTIC Science & Technology

2008-11-21

400001E D/A Spare H 16 0000 48 4000020 PWM Piezo A 16 6230 Formatted Table 3MDS IDD 0BSB2-03-C-0388-01 Rev I 24 21 November 2008 Relative Base...Address (bytes) FPGA Address Item Size (bits) Definition Units/LSB Value/Other 50 4000022 PWM Piezo B 16 6230 52 4000024 PWM Piezo C 16...6230 54 4000026 PWM Piezo D 16 6230 56 4000028 PWM Piezo E 16 6230 58 400002A PWM Piezo F 16 6230 60 400002C Set the starting place for temp sweep 16

Power Quality Control and Design of Power Converter for Variable-Speed Wind Energy Conversion System with Permanent-Magnet Synchronous Generator

PubMed Central

Oğuz, Yüksel; Güney, İrfan; Çalık, Hüseyin

2013-01-01

The control strategy and design of an AC/DC/AC IGBT-PMW power converter for PMSG-based variable-speed wind energy conversion systems (VSWECS) operation in grid/load-connected mode are presented. VSWECS consists of a PMSG connected to a AC-DC IGBT-based PWM rectifier and a DC/AC IGBT-based PWM inverter with LCL filter. In VSWECS, AC/DC/AC power converter is employed to convert the variable frequency variable speed generator output to the fixed frequency fixed voltage grid. The DC/AC power conversion has been managed out using adaptive neurofuzzy controlled inverter located at the output of controlled AC/DC IGBT-based PWM rectifier. In this study, the dynamic performance and power quality of the proposed power converter connected to the grid/load by output LCL filter is focused on. Dynamic modeling and control of the VSWECS with the proposed power converter is performed by using MATLAB/Simulink. Simulation results show that the output voltage, power, and frequency of VSWECS reach to desirable operation values in a very short time. In addition, when PMSG based VSWECS works continuously with the 4.5 kHz switching frequency, the THD rate of voltage in the load terminal is 0.00672%. PMID:24453905

Power quality control and design of power converter for variable-speed wind energy conversion system with permanent-magnet synchronous generator.

PubMed

Oğuz, Yüksel; Güney, İrfan; Çalık, Hüseyin

2013-01-01

The control strategy and design of an AC/DC/AC IGBT-PMW power converter for PMSG-based variable-speed wind energy conversion systems (VSWECS) operation in grid/load-connected mode are presented. VSWECS consists of a PMSG connected to a AC-DC IGBT-based PWM rectifier and a DC/AC IGBT-based PWM inverter with LCL filter. In VSWECS, AC/DC/AC power converter is employed to convert the variable frequency variable speed generator output to the fixed frequency fixed voltage grid. The DC/AC power conversion has been managed out using adaptive neurofuzzy controlled inverter located at the output of controlled AC/DC IGBT-based PWM rectifier. In this study, the dynamic performance and power quality of the proposed power converter connected to the grid/load by output LCL filter is focused on. Dynamic modeling and control of the VSWECS with the proposed power converter is performed by using MATLAB/Simulink. Simulation results show that the output voltage, power, and frequency of VSWECS reach to desirable operation values in a very short time. In addition, when PMSG based VSWECS works continuously with the 4.5 kHz switching frequency, the THD rate of voltage in the load terminal is 0.00672%.

Performance of dual inverter fed open end winding induction motor drive using carrier shift PWM techniques

NASA Astrophysics Data System (ADS)

Priya Darshini, B.; Ranjit, M.; Babu, V. Ramesh

2018-04-01

In this paper different Multicarrier PWM (MCPWM) techniques are proposed for dual inverter fed open end induction motor (IM) drive to achieve multilevel operation. To generate the switching pulses for the dual inverter sinusoidal modulating signal is compared with multi carrier signals. A common mode voltage (CMV) has been analyzed in the proposed open end winding induction motor drive. All the proposed techniques mitigate the CMV along with the harmonic distortion in the phase voltage. To authenticate the proposed work several simulation techniques have been carried out using MATLAB/SIMULINK and the corresponding results are presented and compared.

Temperature Prediction in High Speed Bone Grinding using Motor PWM Signal

PubMed Central

Tai, Bruce L.; Zhang, Lihui; Wang, Anthony C.; Sullivan, Stephen; Wang, Guangjun; Shih, Albert J.

2013-01-01

This research explores the feasibility of using motor electrical feedback to estimate temperature rise during a surgical bone grinding procedure. High-speed bone grinding is often used during skull base neurosurgery to remove cranial bone and approach skull base tumors through the nasal corridor. Grinding-induced heat could propagate and potentially injure surrounding nerves and arteries, and therefore, predicting the temperature in the grinding region would benefit neurosurgeons during the operation. High-speed electric motors are controlled by pulse-width-modulation (PWM) to alter the current input and thus maintain the rotational speed. Assuming full mechanical to thermal power conversion in the grinding process, PWM can be used as feedback for heat generation and temperature prediction. In this study, the conversion model was established from experiments under a variety of grinding conditions and an inverse heat transfer method to determine heat flux. Given a constant rotational speed, the heat conversion was represented by a linear function, and could predict temperature from the experimental data with less than 20% errors. Such results support the advance of this technology for practical application. PMID:23806419

Adolescents' eating behaviour in general and in the peer context: testing the prototype-willingness model.

PubMed

Dohnke, Birte; Steinhilber, Amina; Fuchs, Tanja

2015-01-01

To investigate the prototype-willingness model (PWM) for eating behaviour in general and in the peer context in order to gain further evidence on the PWM and social-reactive processes in adolescents' eating behaviour. A longitudinal study was conducted. PWM variables for unhealthy and healthy eating were assessed at baseline in 356 adolescents (mean age 12.61 years). Eating behaviour was measured four weeks after baseline by two indicators: general eating pattern index (self-report) and consumption of unhealthy and healthy snacks in the peer context (behavioural observation). For both, structural equation models were conducted introducing PWM variables for either unhealthy or healthy eating. The PWM was mainly confirmed for the eating pattern index; intention, willingness and prototype perception had direct effects. Differences between unhealthy and healthy eating were found. Moreover, the PWM contributed to the prediction of healthy, but not unhealthy, snack consumption over and above current hunger; willingness had a direct effect. The PWM can be applied to predict and understand adolescents' eating behaviour. Social-reactive processes, namely willingness and prototype perception, are behavioural determinants that should be considered in theory and as novel targets in health promotion interventions.

Investigation of thermodynamic parameters in the thermal decomposition of plastic waste-waste lube oil compounds.

PubMed

Kim, Yong Sang; Kim, Young Seok; Kim, Sung Hyun

2010-07-01

Thermal decomposition properties of plastic waste-waste lube oil compounds were investigated under nonisothermal conditions. Polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyethylene terephthalate (PET) were selected as representative household plastic wastes. A plastic waste mixture (PWM) and waste lube oil (WLO) were mixed with mixing ratios of 33, 50, and 67 (w/w) % on a PWM weight basis, and thermogravimetric (TG) experiments were performed from 25 to 600 degrees C. The Flynn-Wall method and the Ozawa-Flynn-Wall method were used for analyses of thermodynamic parameters. In this study, activation energies of PWM/WLO compounds ranged from 73.4 to 229.6 kJ/mol between 0.2 and 0.8 of normalized mass conversions, and the 50% PWM/WLO compound had lower activation energies and enthalpies among the PWM/WLO samples at each mass conversion. At the point of maximum differential mass conversion, the analyzed activation energies, enthalpies, entropies, and Gibbs free energies indicated that mixing PWM and WLO has advantages in reducing energy to decrease the degree of disorder. However, no difference in overall energy that would require overcoming both thermal decomposition reactions and degree of disorder was observed among PWM/WLO compounds under these experimental conditions.

Spatial distribution visualization of PWM continuous variable-rate spray

USDA-ARS?s Scientific Manuscript database

Chemical application is a dynamic spatial distribution process, during which spray liquid covers the targets with certain thickness and uniformity. Therefore, it is important to study the 2-D and 3-D (dimensional) spray distribution to evaluate spraying quality. The curve-surface generation methods ...

Temperature prediction in high speed bone grinding using motor PWM signal.

PubMed

Tai, Bruce L; Zhang, Lihui; Wang, Anthony C; Sullivan, Stephen; Wang, Guangjun; Shih, Albert J

2013-10-01

This research explores the feasibility of using motor electrical feedback to estimate temperature rise during a surgical bone grinding procedure. High-speed bone grinding is often used during skull base neurosurgery to remove cranial bone and approach skull base tumors through the nasal corridor. Grinding-induced heat could propagate and potentially injure surrounding nerves and arteries, and therefore, predicting the temperature in the grinding region would benefit neurosurgeons during the operation. High-speed electric motors are controlled by pulse-width-modulation (PWM) to alter the current input and thus maintain the rotational speed. Assuming full mechanical to thermal power conversion in the grinding process, PWM can be used as feedback for heat generation and temperature prediction. In this study, the conversion model was established from experiments under a variety of grinding conditions and an inverse heat transfer method to determine heat flux. Given a constant rotational speed, the heat conversion was represented by a linear function, and could predict temperature from the experimental data with less than 20% errors. Such results support the advance of this technology for practical application. Copyright © 2013 IPEM. Published by Elsevier Ltd. All rights reserved.

Viscosity-adjusted estimation of pressure head and pump flow with quasi-pulsatile modulation of rotary blood pump for a total artificial heart.

PubMed

Yurimoto, Terumi; Hara, Shintaro; Isoyama, Takashi; Saito, Itsuro; Ono, Toshiya; Abe, Yusuke

2016-09-01

Estimation of pressure and flow has been an important subject for developing implantable artificial hearts. To realize real-time viscosity-adjusted estimation of pressure head and pump flow for a total artificial heart, we propose the table estimation method with quasi-pulsatile modulation of rotary blood pump in which systolic high flow and diastolic low flow phased are generated. The table estimation method utilizes three kinds of tables: viscosity, pressure and flow tables. Viscosity is estimated from the characteristic that differential value in motor speed between systolic and diastolic phases varies depending on viscosity. Potential of this estimation method was investigated using mock circulation system. Glycerin solution diluted with salty water was used to adjust viscosity of fluid. In verification of this method using continuous flow data, fairly good estimation could be possible when differential pulse width modulation (PWM) value of the motor between systolic and diastolic phases was high. In estimation under quasi-pulsatile condition, inertia correction was provided and fairly good estimation was possible when the differential PWM value was high, which was not different from the verification results using continuous flow data. In the experiment of real-time estimation applying moving average method to the estimated viscosity, fair estimation could be possible when the differential PWM value was high, showing that real-time viscosity-adjusted estimation of pressure head and pump flow would be possible with this novel estimation method when the differential PWM value would be set high.

Optimal feed-forward compensation for PWM dc/dc converters with 'linear' and 'quadratic' conversion ratio

NASA Astrophysics Data System (ADS)

Calderone, Luigi; Pinola, Licia; Varoli, Vincenzo

1992-04-01

The paper describes an analytical procedure to optimize the feed-forward compensation for any PWM dc/dc converters. The aims of achieving zero dc audiosusceptibility was found to be possible for the buck, buck-boost, Cuk, and SEPIC cells; for the boost converter, however, only nonoptimal compensation is feasible. Rules for the design of PWM controllers and procedures for the evaluation of the hardware-introduced errors are discussed. A PWM controller implementing the optimal feed-forward compensation for buck-boost, Cuk, and SEPIC cells is described and fully experimentally characterized.

Power Electronic Transformer based Three-Phase PWM AC Drives

NASA Astrophysics Data System (ADS)

Basu, Kaushik

A Transformer is used to provide galvanic isolation and to connect systems at different voltage levels. It is one of the largest and most expensive component in most of the high voltage and high power systems. Its size is inversely proportional to the operating frequency. The central idea behind a power electronic transformer (PET) also known as solid state transformer is to reduce the size of the transformer by increasing the frequency. Power electronic converters are used to change the frequency of operation. Steady reduction in the cost of the semiconductor switches and the advent of advanced magnetic materials with very low loss density and high saturation flux density implies economic viability and feasibility of a design with high power density. Application of PET is in generation of power from renewable energy sources, especially wind and solar. Other important application include grid tied inverters, UPS e.t.c. In this thesis non-resonant, single stage, bi-directional PET is considered. The main objective of this converter is to generate adjustable speed and magnitude pulse width modulated (PWM) ac waveforms from an ac or dc grid with a high frequency ac link. The windings of a high frequency transformer contains leakage inductance. Any switching transition of the power electronic converter connecting the inductive load and the transformer requires commutation of leakage energy. Commutation by passive means results in power loss, decrease in the frequency of operation, distortion in the output voltage waveform, reduction in reliability and power density. In this work a source based partially loss-less commutation of leakage energy has been proposed. This technique also results in partial soft-switching. A series of converters with novel PWM strategies have been proposed to minimize the frequency of leakage inductance commutation. These PETs achieve most of the important features of modern PWM ac drives including 1) Input power factor correction, 2) Common-mode voltage suppression at the load end, 3) High quality output voltage waveform (comparable to conventional space vector PWM modulated two level inverter) and 4) Minimization of output voltage loss, common-mode voltage switching and distortion of the load current waveform due to leakage inductance commutation. All of the proposed topologies along with the proposed control schemes have been analyzed and simulated in MATLABSimulink. A hardware prototype has been fabricated and tested. The simulation and experimental results verify the operation and advantages of the proposed topologies and their control.

Shared neuroanatomical substrates of impaired phonological working memory across reading disability and autism

PubMed Central

Lu, Chunming; Qi, Zhenghan; Harris, Adrianne; Weil, Lisa Wisman; Han, Michelle; Halverson, Kelly; Perrachione, Tyler K.; Kjelgaard, Margaret; Wexler, Kenneth; Tager-Flusberg, Helen; Gabrieli, John D. E.

2015-01-01

Background Individuals with reading disability or individuals with autism spectrum disorder (ASD) are characterized, respectively, by their difficulties in reading or social communication, but both groups often have impaired phonological working memory (PWM). It is not known whether the impaired PWM reflects distinct or shared neuroanatomical abnormalities in these two diagnostic groups. Methods White-matter structural connectivity via diffusion weighted imaging was examined in sixty-four children, ages 5-17 years, with reading disability, ASD, or typical development (TD), who were matched in age, gender, intelligence, and diffusion data quality. Results Children with reading disability and children with ASD exhibited reduced PWM compared to children with TD. The two diagnostic groups showed altered white-matter microstructure in the temporo-parietal portion of the left arcuate fasciculus (AF) and in the temporo-occipital portion of the right inferior longitudinal fasciculus (ILF), as indexed by reduced fractional anisotropy and increased radial diffusivity. Moreover, the structural integrity of the right ILF was positively correlated with PWM ability in the two diagnostic groups, but not in the TD group. Conclusions These findings suggest that impaired PWM is transdiagnostically associated with shared neuroanatomical abnormalities in ASD and reading disability. Microstructural characteristics in left AF and right ILF may play important roles in the development of PWM. The right ILF may support a compensatory mechanism for children with impaired PWM. PMID:26949750

Shared neuroanatomical substrates of impaired phonological working memory across reading disability and autism.

PubMed

Lu, Chunming; Qi, Zhenghan; Harris, Adrianne; Weil, Lisa Wisman; Han, Michelle; Halverson, Kelly; Perrachione, Tyler K; Kjelgaard, Margaret; Wexler, Kenneth; Tager-Flusberg, Helen; Gabrieli, John D E

2016-03-01

Individuals with reading disability or individuals with autism spectrum disorder (ASD) are characterized, respectively, by their difficulties in reading or social communication, but both groups often have impaired phonological working memory (PWM). It is not known whether the impaired PWM reflects distinct or shared neuroanatomical abnormalities in these two diagnostic groups. White-matter structural connectivity via diffusion weighted imaging was examined in sixty-four children, ages 5-17 years, with reading disability, ASD, or typical development (TD), who were matched in age, gender, intelligence, and diffusion data quality. Children with reading disability and children with ASD exhibited reduced PWM compared to children with TD. The two diagnostic groups showed altered white-matter microstructure in the temporo-parietal portion of the left arcuate fasciculus (AF) and in the temporo-occipital portion of the right inferior longitudinal fasciculus (ILF), as indexed by reduced fractional anisotropy and increased radial diffusivity. Moreover, the structural integrity of the right ILF was positively correlated with PWM ability in the two diagnostic groups, but not in the TD group. These findings suggest that impaired PWM is transdiagnostically associated with shared neuroanatomical abnormalities in ASD and reading disability. Microstructural characteristics in left AF and right ILF may play important roles in the development of PWM. The right ILF may support a compensatory mechanism for children with impaired PWM.

[System design of small intellectualized ultrasound hyperthermia instrument in the LabVIEW environment].

PubMed

Jiang, Feng; Bai, Jingfeng; Chen, Yazhu

2005-08-01

Small-scale intellectualized medical instrument has attracted great attention in the field of biomedical engineering, and LabVIEW (Laboratory Virtual Instrument Engineering Workbench) provides a convenient environment for this application due to its inherent advantages. The principle and system structure of the hyperthermia instrument are presented. Type T thermocouples are employed as thermotransducers, whose amplifier consists of two stages, providing built-in ice point compensation and thus improving work stability over temperature. Control signals produced by specially designed circuit drive the programmable counter/timer 8254 chip to generate PWM (Pulse width modulation) wave, which is used as ultrasound radiation energy control signal. Subroutine design topics such as inner-tissue real time feedback temperature control algorithm, water temperature control in the ultrasound applicator are also described. In the cancer tissue temperature control subroutine, the authors exert new improvments to PID (Proportional Integral Differential) algorithm according to the specific demands of the system and achieve strict temperature control to the target tissue region. The system design and PID algorithm improvement have experimentally proved to be reliable and excellent, meeting the requirements of the hyperthermia system.

A wideband dual-antenna receiver for wireless recording from animals behaving in large arenas.

PubMed

Lee, Seung Bae; Yin, Ming; Manns, Joseph R; Ghovanloo, Maysam

2013-07-01

A low-noise wideband receiver (Rx) is presented for a multichannel wireless implantable neural recording (WINeR) system that utilizes time-division multiplexing of pulse width modulated (PWM) samples. The WINeR-6 Rx consists of four parts: 1) RF front end; 2) signal conditioning; 3) analog output (AO); and 4) field-programmable gate array (FPGA) back end. The RF front end receives RF-modulated neural signals in the 403-490 MHz band with a wide bandwidth of 18 MHz. The frequency-shift keying (FSK) PWM demodulator in the FPGA is a time-to-digital converter with 304 ps resolution, which converts the analog pulse width information to 16-bit digital samples. Automated frequency tracking has been implemented in the Rx to lock onto the free-running voltage-controlled oscillator in the transmitter (Tx). Two antennas and two parallel RF paths are used to increase the wireless coverage area. BCI-2000 graphical user interface has been adopted and modified to acquire, visualize, and record the recovered neural signals in real time. The AO module picks three demultiplexed channels and converts them into analog signals for direct observation on an oscilloscope. One of these signals is further amplified to generate an audio output, offering users the ability to listen to ongoing neural activity. Bench-top testing of the Rx performance with a 32-channel WINeR-6 Tx showed that the input referred noise of the entire system at a Tx-Rx distance of 1.5 m was 4.58 μV rms with 8-bit resolution at 640 kSps. In an in vivo experiment, location-specific receptive fields of hippocampal place cells were mapped during a behavioral experiment in which a rat completed 40 laps in a large circular track. Results were compared against those acquired from the same animal and the same set of electrodes by a commercial hardwired recording system to validate the wirelessly recorded signals.

A Wideband Dual-Antenna Receiver for Wireless Recording From Animals Behaving in Large Arenas

PubMed Central

Lee, Seung Bae; Yin, Ming; Manns, Joseph R.

2014-01-01

A low-noise wideband receiver (Rx) is presented for a multichannel wireless implantable neural recording (WINeR) system that utilizes time-division multiplexing of pulse width modulated (PWM) samples. The WINeR-6 Rx consists of four parts: 1) RF front end; 2) signal conditioning; 3) analog output (AO); and 4) field-programmable gate array (FPGA) back end. The RF front end receives RF-modulated neural signals in the 403–490 MHz band with a wide bandwidth of 18 MHz. The frequency-shift keying (FSK) PWM demodulator in the FPGA is a time-to-digital converter with 304 ps resolution, which converts the analog pulse width information to 16-bit digital samples. Automated frequency tracking has been implemented in the Rx to lock onto the free-running voltage-controlled oscillator in the transmitter (Tx). Two antennas and two parallel RF paths are used to increase the wireless coverage area. BCI-2000 graphical user interface has been adopted and modified to acquire, visualize, and record the recovered neural signals in real time. The AO module picks three demultiplexed channels and converts them into analog signals for direct observation on an oscilloscope. One of these signals is further amplified to generate an audio output, offering users the ability to listen to ongoing neural activity. Bench-top testing of the Rx performance with a 32-channel WINeR-6 Tx showed that the input referred noise of the entire system at a Tx–Rx distance of 1.5 m was 4.58 μVrms with 8-bit resolution at 640 kSps. In an in vivo experiment, location-specific receptive fields of hippocampal place cells were mapped during a behavioral experiment in which a rat completed 40 laps in a large circular track. Results were compared against those acquired from the same animal and the same set of electrodes by a commercial hardwired recording system to validate the wirelessly recorded signals. PMID:23428612

Modeling and Simulation of a DG-Integrated Intelligent Microgrid

DTIC Science & Technology

2010-02-01

17. The I-V curve from the manufacturer for BP-4175 175W PV module...........................32   Fig. 18. Wind turbine model...33   Fig. 19. Electrical outputs of wind turbine... PMSG : Permanent Magnet Synchronous Generator PLL : Phase Lock Loop PV : Photovoltaic PWM : Pulse Width Modulation TOU : Time of Use VTES

BIPAD: A web server for modeling bipartite sequence elements

PubMed Central

Bi, Chengpeng; Rogan, Peter K

2006-01-01

Background Many dimeric protein complexes bind cooperatively to families of bipartite nucleic acid sequence elements, which consist of pairs of conserved half-site sequences separated by intervening distances that vary among individual sites. Results We introduce the Bipad Server [1], a web interface to predict sequence elements embedded within unaligned sequences. Either a bipartite model, consisting of a pair of one-block position weight matrices (PWM's) with a gap distribution, or a single PWM matrix for contiguous single block motifs may be produced. The Bipad program performs multiple local alignment by entropy minimization and cyclic refinement using a stochastic greedy search strategy. The best models are refined by maximizing incremental information contents among a set of potential models with varying half site and gap lengths. Conclusion The web service generates information positional weight matrices, identifies binding site motifs, graphically represents the set of discovered elements as a sequence logo, and depicts the gap distribution as a histogram. Server performance was evaluated by generating a collection of bipartite models for distinct DNA binding proteins. PMID:16503993

Color adjustable LED driver design based on PWM

NASA Astrophysics Data System (ADS)

Du, Yiying; Yu, Caideng; Que, Longcheng; Zhou, Yun; Lv, Jian

2012-10-01

Light-emitting diode (LED) is a liquid cold source light source that rapidly develops in recent years. The merits of high brightness efficiency, long duration, high credibility and no pollution make it satisfy our demands for consumption and natural life, and gradually replace the traditional lamp-house-incandescent light and fluorescent light. However, because of the high cost and unstable drive circuit, the application range is restricted. To popularize the applications of the LED, we focus on improving the LED driver circuit to change this phenomenon. Basing on the traditional LED drive circuit, we adopt pre-setup constant current model and introduce pulse width modulation (PWM) control method to realize adjustable 256 level-grays display. In this paper, basing on human visual characteristics and the traditional PWM control method, we propose a new PWM control timing clock to alter the duty cycle of PWM signal to realize the simple gamma correction. Consequently, the brightness can accord with our visual characteristics.

Reasoned versus reactive prediction of behaviour: a meta-analysis of the prototype willingness model.

PubMed

Todd, Jemma; Kothe, Emily; Mullan, Barbara; Monds, Lauren

2016-01-01

The prototype willingness model (PWM) was designed to extend expectancy-value models of health behaviour by also including a heuristic, or social reactive pathway, to better explain health-risk behaviours in adolescents and young adults. The pathway includes prototype, i.e., images of a typical person who engages in a behaviour, and willingness to engage in behaviour. The current study describes a meta-analysis of predictive research using the PWM and explores the role of the heuristic pathway and intentions in predicting behaviour. Eighty-one studies met inclusion criteria. Overall, the PWM was supported and explained 20.5% of the variance in behaviour. Willingness explained 4.9% of the variance in behaviour over and above intention, although intention tended to be more strongly related to behaviour than was willingness. The strength of the PWM relationships tended to vary according to the behaviour being tested, with alcohol consumption being the behaviour best explained. Age was also an important moderator, and, as expected, PWM behaviour was best accounted for within adolescent samples. Results were heterogeneous even after moderators were taken into consideration. This meta-analysis provides support for the PWM and may be used to inform future interventions that can be tailored for at-risk populations.

Are organ donation communication decisions reasoned or reactive? A test of the utility of an augmented theory of planned behaviour with the prototype/willingness model.

PubMed

Hyde, Melissa K; White, Katherine M

2010-05-01

To explore whether people's organ donation consent decisions occur via a reasoned and/or social reaction pathway. We examined prospectively students' and community members' decisions to register consent on a donor register and discuss organ donation wishes with family. Participants completed items assessing theory of planned behaviour (TPB; attitude, subjective norm, perceived behavioural control (PBC)), prototype/willingness model (PWM; donor prototype favourability/similarity, past behaviour), and proposed additional influences (moral norm, self-identity, recipient prototypes) for registering (N=339) and discussing (N=315) intentions/willingness. Participants self-reported their registering (N=177) and discussing (N=166) behaviour 1 month later. The utility of the (1) TPB, (2) PWM, (3) augmented TPB with PWM, and (4) augmented TPB with PWM and extensions was tested using structural equation modelling for registering and discussing intentions/willingness, and logistic regression for behaviour. While the TPB proved a more parsimonious model, fit indices suggested that the other proposed models offered viable options, explaining greater variance in communication intentions/willingness. The TPB, augmented TPB with PWM, and extended augmented TPB with PWM best explained registering and discussing decisions. The proposed and revised PWM also proved an adequate fit for discussing decisions. Respondents with stronger intentions (and PBC for registering) had a higher likelihood of registering and discussing. People's decisions to communicate donation wishes may be better explained via a reasoned pathway (especially for registering); however, discussing involves more reactive elements. The role of moral norm, self-identity, and prototypes as influences predicting communication decisions were highlighted also.

Enhanced Detection of Chromosomal Abnormalities in Chronic Lymphocytic Leukemia by Conventional Cytogenetics Using CpG Oligonucleotide in Combination with Pokeweed Mitogen and Phorbol Myristate Acetate

PubMed Central

Muthusamy, Natarajan; Breidenbach, Heather; Andritsos, Leslie; Flynn, Joseph; Jones, Jeffrey; Ramanunni, Asha; Mo, Xiaokui; Jarjoura, David; Byrd, John C.; Heerema, Nyla A.

2011-01-01

Reproducible cytogenetic analysis in CLL has been limited by the inability to obtain reliable metaphase cells for analysis. CpG oligonucleotide and cytokine stimulation have been shown to improve metaphase analysis of CLL cytogenetic abnormalities, but is limited by variability in the cytokine receptor levels, stability and biological activity of the cytokine in culture conditions and high costs associated with these reagents. We report here use of a novel, stable CpG, GNKG168 along with pokeweed mitogen (PWM) and phorbol 12-myristate 13-acetate (PMA) for conventional cytogenetic assessment in CLL. We demonstrate that the combined use of GNKG168+PWM/PMA increased the sensitivity of detection of chromosomal abnormalities compared to PWM/PMA (n=207, odds ratio=2.2, p=0.0002) and GNKG168 (n=219, odds ratio=1.5, p=0.0452). Further, a significant increase in sensitivity to detect complexity ≥3 with GNKG168+PWM/PMA compared to GNKG168 alone (odds ratio 8.0, p=0.0022) or PWM/PMA alone (odds ratio 9.6, p=0.0007) was observed. The trend toward detection of higher complexity was significantly greater with GNKG168+PWM/PMA compared to GNKG168 alone (p=0.0412). The increased sensitivity was mainly attributed to the addition of PWM/PMA with GNKG168 because GNKG168 alone showed no difference in sensitivity for detection of complex abnormalities (p=0.17). Comparison of fluorescence in situ hybridization (FISH) results with karyotypic results showed a high degree of consistency, although some complex karyotypes were present in cases with no adverse FISH abnormality. These studies provide evidence for potential use of GNKG168 in combination with PWM and PMA in karyotypic analysis of CLL patient samples to better identify chromosomal abnormalities for risk stratification. PMID:21494579

Research on single-chip microcomputer controlled rotating magnetic field mineralization model

NASA Astrophysics Data System (ADS)

Li, Yang; Qi, Yulin; Yang, Junxiao; Li, Na

2017-08-01

As one of the method of selecting ore, the magnetic separation method has the advantages of stable operation, simple process flow, high beneficiation efficiency and no chemical environment pollution. But the existing magnetic separator are more mechanical, the operation is not flexible, and can not change the magnetic field parameters according to the precision of the ore needed. Based on the existing magnetic separator is mechanical, the rotating magnetic field can be used for single chip microcomputer control as the research object, design and trial a rotating magnetic field processing prototype, and through the single-chip PWM pulse output to control the rotation of the magnetic field strength and rotating magnetic field speed. This method of using pure software to generate PWM pulse to control rotary magnetic field beneficiation, with higher flexibility, accuracy and lower cost, can give full play to the performance of single-chip.

The 120V 20A PWM switch for applications in high power distribution

NASA Astrophysics Data System (ADS)

Borelli, V.; Nimal, W.

1989-08-01

A 20A/120VDC (voltage direct current) PWM (Pulse Width Modulation) Solid State Power Controller (SSPC) developed under ESA contract to be used in the power distribution system of Columbus is described. The general characteristics are discussed and the project specification defined. The benefits of a PWM solution over a more conventional approach, for the specific application considered are presented. An introduction to the SSPC characteristics and a functional description are presented.

Highly Sensitive and Wide-Dynamic-Range Multichannel Optical-Fiber pH Sensor Based on PWM Technique.

PubMed

Khan, Md Rajibur Rahaman; Kang, Shin-Won

2016-11-09

In this study, we propose a highly sensitive multichannel pH sensor that is based on an optical-fiber pulse width modulation (PWM) technique. According to the optical-fiber PWM method, the received sensing signal's pulse width changes when the optical-fiber pH sensing-element of the array comes into contact with pH buffer solutions. The proposed optical-fiber PWM pH-sensing system offers a linear sensing response over a wide range of pH values from 2 to 12, with a high pH-sensing ability. The sensitivity of the proposed pH sensor is 0.46 µs/pH, and the correlation coefficient R² is approximately 0.997. Additional advantages of the proposed optical-fiber PWM pH sensor include a short/fast response-time of about 8 s, good reproducibility properties with a relative standard deviation (RSD) of about 0.019, easy fabrication, low cost, small size, reusability of the optical-fiber sensing-element, and the capability of remote sensing. Finally, the performance of the proposed PWM pH sensor was compared with that of potentiometric, optical-fiber modal interferometer, and optical-fiber Fabry-Perot interferometer pH sensors with respect to dynamic range width, linearity as well as response and recovery times. We observed that the proposed sensing systems have better sensing abilities than the above-mentioned pH sensors.

Highly Sensitive and Wide-Dynamic-Range Multichannel Optical-Fiber pH Sensor Based on PWM Technique

PubMed Central

Khan, Md. Rajibur Rahaman; Kang, Shin-Won

2016-01-01

In this study, we propose a highly sensitive multichannel pH sensor that is based on an optical-fiber pulse width modulation (PWM) technique. According to the optical-fiber PWM method, the received sensing signal’s pulse width changes when the optical-fiber pH sensing-element of the array comes into contact with pH buffer solutions. The proposed optical-fiber PWM pH-sensing system offers a linear sensing response over a wide range of pH values from 2 to 12, with a high pH-sensing ability. The sensitivity of the proposed pH sensor is 0.46 µs/pH, and the correlation coefficient R2 is approximately 0.997. Additional advantages of the proposed optical-fiber PWM pH sensor include a short/fast response-time of about 8 s, good reproducibility properties with a relative standard deviation (RSD) of about 0.019, easy fabrication, low cost, small size, reusability of the optical-fiber sensing-element, and the capability of remote sensing. Finally, the performance of the proposed PWM pH sensor was compared with that of potentiometric, optical-fiber modal interferometer, and optical-fiber Fabry–Perot interferometer pH sensors with respect to dynamic range width, linearity as well as response and recovery times. We observed that the proposed sensing systems have better sensing abilities than the above-mentioned pH sensors. PMID:27834865

Pegasus power system facility upgrades

NASA Astrophysics Data System (ADS)

Lewicki, B. T.; Kujak-Ford, B. A.; Winz, G. R.

2008-11-01

Two key Pegasus systems have been recently upgraded: the Ohmic-transformer IGCT bridge control system, and the plasma-gun injector power system. The Ohmic control system contains two new microprocessor controlled components to provide an interface between the PWM controller and the IGCT bridges. An interface board conditions the command signals from the PWM controller. A splitter/combiner board routes the conditioned PWM commands to an array of IGCT bridges and interprets IGCT bridge status. This system allows for any PWM controller to safely control IGCT bridges. Future developments will include a transition to a polyphasic bridge control. This will allow for 3 to 4 times the present pulse length and provide a much higher switching frequency. The plasma gun injector system now includes active current feedback control on gun bias current via PWM buck type power supplies. Near term goals include a doubling or tripling of the applied bias voltage. Future arc bias system power supplies may include a simpler boost type system which will allow access to even higher voltages using existing low voltage energy storage systems.

The chording effect on core losses of three-phase induction motor under sinusoidal and PWM voltage supplies

NASA Astrophysics Data System (ADS)

Deshmukh, Ram; Moses, A. J.; Anayi, F.

The core losses and the lower-order voltage harmonics of four different chorded motors fed from sinusoidal supply and inverter voltage supply were invigilated at no-load condition. All the four motors were tested with 4, 8 and 16 kHz switching frequencies and 30, 40, 50 and 60 Hz modulation frequencies The motor with 120° coil pitch has the least core losses and the lower-order voltage harmonics under sinusoidal and pulse width modulation (PWM) voltage supplies at all switching and modulation frequencies. The drop in the core losses for this motor was 46% and 53% under sinusoidal and PWM voltage supplies, respectively. The motor with 120° coil pitch is recommended to be used under sinusoidal and PWM voltage supplies.

Precision-controlled elution of a 82Sr/82Rb generator for cardiac perfusion imaging with positron emission tomography

NASA Astrophysics Data System (ADS)

Klein, R.; Adler, A.; Beanlands, R. S.; de Kemp, R. A.

2007-02-01

A rubidium-82 (82Rb) elution system is described for use with positron emission tomography. Due to the short half-life of 82Rb (76 s), the system physics must be modelled precisely to account for transport delay and the associated activity decay and dispersion. Saline flow is switched between a 82Sr/82Rb generator and a bypass line to achieve a constant-activity elution of 82Rb. Pulse width modulation (PWM) of a solenoid valve is compared to simple threshold control as a means to simulate a proportional valve. A predictive-corrective control (PCC) algorithm is developed which produces a constant-activity elution within the constraints of long feedback delay and short elution time. The system model parameters are adjusted through a self-tuning algorithm to minimize error versus the requested time-activity profile. The system is self-calibrating with 2.5% repeatability, independent of generator activity and elution flow rate. Accurate 30 s constant-activity elutions of 10-70% of the total generator activity are achieved using both control methods. The combined PWM-PCC method provides significant improvement in precision and accuracy of the requested elution profiles. The 82Rb elution system produces accurate and reproducible constant-activity elution profiles of 82Rb activity, independent of parent 82Sr activity in the generator. More reproducible elution profiles may improve the quality of clinical and research PET perfusion studies using 82Rb.

Precision-controlled elution of a 82Sr/82Rb generator for cardiac perfusion imaging with positron emission tomography.

PubMed

Klein, R; Adler, A; Beanlands, R S; Dekemp, R A

2007-02-07

A rubidium-82 ((82)Rb) elution system is described for use with positron emission tomography. Due to the short half-life of (82)Rb (76 s), the system physics must be modelled precisely to account for transport delay and the associated activity decay and dispersion. Saline flow is switched between a (82)Sr/(82)Rb generator and a bypass line to achieve a constant-activity elution of (82)Rb. Pulse width modulation (PWM) of a solenoid valve is compared to simple threshold control as a means to simulate a proportional valve. A predictive-corrective control (PCC) algorithm is developed which produces a constant-activity elution within the constraints of long feedback delay and short elution time. The system model parameters are adjusted through a self-tuning algorithm to minimize error versus the requested time-activity profile. The system is self-calibrating with 2.5% repeatability, independent of generator activity and elution flow rate. Accurate 30 s constant-activity elutions of 10-70% of the total generator activity are achieved using both control methods. The combined PWM-PCC method provides significant improvement in precision and accuracy of the requested elution profiles. The (82)Rb elution system produces accurate and reproducible constant-activity elution profiles of (82)Rb activity, independent of parent (82)Sr activity in the generator. More reproducible elution profiles may improve the quality of clinical and research PET perfusion studies using (82)Rb.

Real-time multi-DSP control of three-phase current-source unity power factor PWM rectifier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao Wang; Boon-Teck Ooi

1993-07-01

The design of a real-time multi-DSP controller for a high-quality six-valve three-phase current-source unity power factor PWM rectifier is discussed in this paper. With the decoupler preprocessor and the dynamic trilogic PWM trigger scheme, each of the three input currents can be controlled independently. Based on the a-b-c frame system model and the fast parallel computer control, the pole-placement control method is implemented successfully to achieve fast response in the ac currents. The low-frequency resonance in the ac filter L-C networks has been damped effectively. The experimental results are obtained from a 1-kVA bipolar transistor current-source PWM rectifier with amore » real-time controller using three TMS320C25 DSP's.« less

A Passive EMI Filter with Access to the Ungrounded Motor Neutral Line-The Case that a General-Purpose Inverter is Directly Connected to a Three-Phase Grounded Voltage Source-

NASA Astrophysics Data System (ADS)

Doumoto, Takafumi; Akagi, Hirofumi

This paper proposes a small-sized passive EMI filter for the purpose of eliminating high-frequency shaft voltage and ground leakage current from an ac motor. The motor is driven by a general-purpose PWM inverter connected to a three-phase grounded voltage source. The passive EMI filter requires access to the ungrounded neutral point of the motor. This unique circuit configuration makes the common-mode inductor effective in reducing the high-frequency common-mode voltage generated by the PWM inverter with a carrier frequency of 15kHz. As a result, both high-frequency shaft voltage and ground leakage current can be eliminated very efficiently. However, the common-mode inductor may not play any role in reducing the low-frequency common-mode voltage generated by the diode rectifier, so that a low-frequency component still remains in the shaft voltage. Such a low-frequency shaft voltage may not produce any bad effect on motor bearings. The validity and effectiveness of the EMI filter is verified by experimental results obtained from a 200-V 5-kVA laboratory system.

Linkage and mapping of quantitative trait loci associated with angular leaf spot and powdery mildew resistance in common beans.

PubMed

Bassi, Denis; Briñez, Boris; Rosa, Juliana Santa; Oblessuc, Paula Rodrigues; Almeida, Caléo Panhoca de; Nucci, Stella Maris; Silva, Larissa Chariel Domingos da; Chiorato, Alisson Fernando; Vianello, Rosana Pereira; Camargo, Luis Eduardo Aranha; Blair, Matthew Wohlgemuth; Benchimol-Reis, Luciana Lasry

2017-01-01

Angular leaf spot (ALS) and powdery mildew (PWM) are two important fungi diseases causing significant yield losses in common beans. In this study, a new genetic linkage map was constructed using single sequence repeats (SSRs) and single nucleotide polymorphisms (SNPs), in a segregating population derived from the AND 277 x SEA 5 cross, with 105 recombinant inbred lines. Phenotypic evaluations were performed in the greenhouse to identify quantitative trait loci (QTLs) associated with resistance by means of the composite interval mapping analysis. Four QTLs were identified for ALS resistance. The QTL ALS11AS, linked on the SNP BAR 5054, mapped on chromosome Pv11, showed the greatest effect (R2 = 26.5%) on ALS phenotypic variance. For PWM resistance, two QTLs were detected, PWM2AS and PWM11AS, on Pv2 and Pv11, explaining 7% and 66% of the phenotypic variation, respectively. Both QTLs on Pv11 were mapped on the same genomic region, suggesting that it is a pleiotropic region. The present study resulted in the identification of new markers closely linked to ALS and PWM QTLs, which can be used for marker-assisted selection, fine mapping and positional cloning.

Instrumentation System Diagnoses a Thermocouple

NASA Technical Reports Server (NTRS)

Perotti, Jose; Santiago, Josephine; Mata, Carlos; Vokrot, Peter; Zavala, Carlos; Burns, Bradley

2008-01-01

An improved self-validating thermocouple (SVT) instrumentation system not only acquires readings from a thermocouple but is also capable of detecting deterioration and a variety of discrete faults in the thermocouple and its lead wires. Prime examples of detectable discrete faults and deterioration include open- and short-circuit conditions and debonding of the thermocouple junction from the object, the temperature of which one seeks to measure. Debonding is the most common cause of errors in thermocouple measurements, but most prior SVT instrumentation systems have not been capable of detecting debonding. The improved SVT instrumentation system includes power circuitry, a cold-junction compensator, signal-conditioning circuitry, pulse-width-modulation (PWM) thermocouple-excitation circuitry, an analog-to-digital converter (ADC), a digital data processor, and a universal serial bus (USB) interface. The system can operate in any of the following three modes: temperature measurement, thermocouple validation, and bonding/debonding detection. The software running in the processor includes components that implement statistical algorithms to evaluate the state of the thermocouple and the instrumentation system. When the power is first turned on, the user can elect to start a diagnosis/ monitoring sequence, in which the PWM is used to estimate the characteristic times corresponding to the correct configuration. The user also has the option of using previous diagnostic values, which are stored in an electrically erasable, programmable read-only memory so that they are available every time the power is turned on.

Effect of different methods of pulse width modulation on power losses in an induction motor

NASA Astrophysics Data System (ADS)

Gulyaev, Alexander; Fokin, Dmitrii; Shuharev, Sergey; Ten, Evgenii

2017-10-01

We consider the calculation of modulation power losses in a system “induction motor-inverter” for various pulse width modulation (PWM) methods of the supply voltage. Presented values of modulation power losses are the result of modeling a system “DC link - two-level three-phase voltage inverter - induction motor - load”. In this study the power losses in a system “induction motor - inverter” are computed, as well as losses caused by higher harmonics of PWM supply voltage, followed by definition of active power consumed by the DC link for a specified value mechanical power on the induction motor shaft. Mechanical power was determined by the rotation speed and the torque on the motor shaft in various quasi-sinusoidal supply voltage PWM modes. These calculations reveal the best coefficient of performance (COP) in a system of a variable frequency drive (VFD) with independent voltage inverter controlled by induction motor PWM.

Dithering Digital Ripple Correlation Control for Photovoltaic Maximum Power Point Tracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barth, C; Pilawa-Podgurski, RCN

This study demonstrates a new method for rapid and precise maximum power point tracking in photovoltaic (PV) applications using dithered PWM control. Constraints imposed by efficiency, cost, and component size limit the available PWM resolution of a power converter, and may in turn limit the MPP tracking efficiency of the PV system. In these scenarios, PWM dithering can be used to improve average PWM resolution. In this study, we present a control technique that uses ripple correlation control (RCC) on the dithering ripple, thereby achieving simultaneous fast tracking speed and high tracking accuracy. Moreover, the proposed method solves some ofmore » the practical challenges that have to date limited the effectiveness of RCC in solar PV applications. We present a theoretical derivation of the principles behind dithering digital ripple correlation control, as well as experimental results that show excellent tracking speed and accuracy with basic hardware requirements.« less

Transistorized PWM inverter-induction motor drive system

NASA Technical Reports Server (NTRS)

Peak, S. C.; Plunkett, A. B.

1982-01-01

This paper describes the development of a transistorized PWM inverter-induction motor traction drive system. A vehicle performance analysis was performed to establish the vehicle tractive effort-speed requirements. These requirements were then converted into a set of inverter and motor specifications. The inverter was a transistorized three-phase bridge using General Electric power Darlington transistors. The description of the design and development of this inverter is the principal object of this paper. The high-speed induction motor is a design which is optimized for use with an inverter power source. The primary feedback control is a torque angle control with voltage and torque outer loop controls. A current-controlled PWM technique is used to control the motor voltage. The drive has a constant torque output with PWM operation to base motor speed and a constant horsepower output with square wave operation to maximum speed. The drive system was dynamometer tested and the results are presented.

Full-Circle Resolver-to-Linear-Analog Converter

NASA Technical Reports Server (NTRS)

Alhorn, Dean C.; Smith, Dennis A.; Howard, David E.

2005-01-01

A circuit generates sinusoidal excitation signals for a shaft-angle resolver and, like the arctangent circuit described in the preceding article, generates an analog voltage proportional to the shaft angle. The disadvantages of the circuit described in the preceding article arise from the fact that it must be made from precise analog subcircuits, including a functional block capable of implementing some trigonometric identities; this circuitry tends to be expensive, sensitive to noise, and susceptible to errors caused by temperature-induced drifts and imprecise matching of gains and phases. These disadvantages are overcome by the design of the present circuit. The present circuit (see figure) includes an excitation circuit, which generates signals Ksin(Omega(t)) and Kcos(Omega(t)) [where K is an amplitude, Omega denotes 2(pi)x a carrier frequency (the design value of which is 10 kHz), and t denotes time]. These signals are applied to the excitation terminals of a shaft-angle resolver, causing the resolver to put out signals C sin(Omega(t)-Theta) and C cos(Omega(t)-Theta). The cosine excitation signal and the cosine resolver output signal are processed through inverting comparator circuits, which are configured to function as inverting squarers, to obtain logic-level or square-wave signals .-LL[cos(Omega(t)] and -LL[cos(Omega(t)-Theta)], respectively. These signals are fed as inputs to a block containing digital logic circuits that effectively measure the phase difference (which equals Theta between the two logic-level signals). The output of this block is a pulse-width-modulated signal, PWM(Theta), the time-averaged value of which ranges from 0 to 5 VDC as Theta ranges from .180 to +180deg. PWM(Theta) is fed to a block of amplifying and level-shifting circuitry, which converts the input PWM waveform to an output waveform that switches between precise reference voltage levels of +10 and -10 V. This waveform is processed by a two-pole, low-pass filter, which removes the carrier-frequency component. The final output signal is a DC potential, proportional to Theta that ranges continuously from -10 V at Theta = -180deg to +10 V at Theta = +180deg..

Linkage and mapping of quantitative trait loci associated with angular leaf spot and powdery mildew resistance in common beans

PubMed Central

Bassi, Denis; Briñez, Boris; Rosa, Juliana Santa; Oblessuc, Paula Rodrigues; de Almeida, Caléo Panhoca; Nucci, Stella Maris; da Silva, Larissa Chariel Domingos; Chiorato, Alisson Fernando; Vianello, Rosana Pereira; Camargo, Luis Eduardo Aranha; Blair, Matthew Wohlgemuth; Benchimol-Reis, Luciana Lasry

2017-01-01

Abstract Angular leaf spot (ALS) and powdery mildew (PWM) are two important fungi diseases causing significant yield losses in common beans. In this study, a new genetic linkage map was constructed using single sequence repeats (SSRs) and single nucleotide polymorphisms (SNPs), in a segregating population derived from the AND 277 x SEA 5 cross, with 105 recombinant inbred lines. Phenotypic evaluations were performed in the greenhouse to identify quantitative trait loci (QTLs) associated with resistance by means of the composite interval mapping analysis. Four QTLs were identified for ALS resistance. The QTL ALS11AS, linked on the SNP BAR 5054, mapped on chromosome Pv11, showed the greatest effect (R2 = 26.5%) on ALS phenotypic variance. For PWM resistance, two QTLs were detected, PWM2AS and PWM11AS, on Pv2 and Pv11, explaining 7% and 66% of the phenotypic variation, respectively. Both QTLs on Pv11 were mapped on the same genomic region, suggesting that it is a pleiotropic region. The present study resulted in the identification of new markers closely linked to ALS and PWM QTLs, which can be used for marker-assisted selection, fine mapping and positional cloning. PMID:28222201

Spelling errors among children with ADHD symptoms: the role of working memory.

PubMed

Re, Anna Maria; Mirandola, Chiara; Esposito, Stefania Sara; Capodieci, Agnese

2014-09-01

Research has shown that children with attention deficit/hyperactivity disorder (ADHD) may present a series of academic difficulties, including spelling errors. Given that correct spelling is supported by the phonological component of working memory (PWM), the present study examined whether or not the spelling difficulties of children with ADHD are emphasized when children's PWM is overloaded. A group of 19 children with ADHD symptoms (between 8 and 11 years of age), and a group of typically developing children matched for age, schooling, gender, rated intellectual abilities, and socioeconomic status, were administered two dictation texts: one under typical conditions and one under a pre-load condition that required the participants to remember a series of digits while writing. The results confirmed that children with ADHD symptoms have spelling difficulties, produce a higher percentages of errors compared to the control group children, and that these difficulties are enhanced under a higher load of PWM. An analysis of errors showed that this holds true, especially for phonological errors. The increased errors in the PWM condition was not due to a tradeoff between working memory and writing, as children with ADHD also performed more poorly in the PWM task. The theoretical and practical implications are discussed. Copyright © 2014 Elsevier Ltd. All rights reserved.

LDMOS Channel Thermometer Based on a Thermal Resistance Sensor for Balancing Temperature in Monolithic Power ICs.

PubMed

Lin, Tingyou; Ho, Yingchieh; Su, Chauchin

2017-06-15

This paper presents a method of thermal balancing for monolithic power integrated circuits (ICs). An on-chip temperature monitoring sensor that consists of a poly resistor strip in each of multiple parallel MOSFET banks is developed. A temperature-to-frequency converter (TFC) is proposed to quantize on-chip temperature. A pulse-width-modulation (PWM) methodology is developed to balance the channel temperature based on the quantization. The modulated PWM pulses control the hottest of metal-oxide-semiconductor field-effect transistor (MOSFET) bank to reduce its power dissipation and heat generation. A test chip with eight parallel MOSFET banks is fabricated in TSMC 0.25 μm HV BCD processes, and total area is 900 × 914 μm². The maximal temperature variation among the eight banks can reduce to 2.8 °C by the proposed thermal balancing system from 9.5 °C with 1.5 W dissipation. As a result, our proposed system improves the lifetime of a power MOSFET by 20%.

LDMOS Channel Thermometer Based on a Thermal Resistance Sensor for Balancing Temperature in Monolithic Power ICs

PubMed Central

Lin, Tingyou; Ho, Yingchieh; Su, Chauchin

2017-01-01

This paper presents a method of thermal balancing for monolithic power integrated circuits (ICs). An on-chip temperature monitoring sensor that consists of a poly resistor strip in each of multiple parallel MOSFET banks is developed. A temperature-to-frequency converter (TFC) is proposed to quantize on-chip temperature. A pulse-width-modulation (PWM) methodology is developed to balance the channel temperature based on the quantization. The modulated PWM pulses control the hottest of metal-oxide-semiconductor field-effect transistor (MOSFET) bank to reduce its power dissipation and heat generation. A test chip with eight parallel MOSFET banks is fabricated in TSMC 0.25 μm HV BCD processes, and total area is 900 × 914 μm2. The maximal temperature variation among the eight banks can reduce to 2.8 °C by the proposed thermal balancing system from 9.5 °C with 1.5 W dissipation. As a result, our proposed system improves the lifetime of a power MOSFET by 20%. PMID:28617346

Electrical motor/generator drive apparatus and method

DOEpatents

Su, Gui Jia

2013-02-12

The present disclosure includes electrical motor/generator drive systems and methods that significantly reduce inverter direct-current (DC) bus ripple currents and thus the volume and cost of a capacitor. The drive methodology is based on a segmented drive system that does not add switches or passive components but involves reconfiguring inverter switches and motor stator winding connections in a way that allows the formation of multiple, independent drive units and the use of simple alternated switching and optimized Pulse Width Modulation (PWM) schemes to eliminate or significantly reduce the capacitor ripple current.

An analog method of cross-talk compensation for a RGB wavelength division multiplexed optical link

NASA Astrophysics Data System (ADS)

Chisholm, George; Leveneur, Jérôme; Futter, John; Kennedy, John

2018-06-01

Pulse-width modulation (PWM) over optical fiber can be a very advantageous data transmission approach when an electrically isolated data link is required. The use of wavelength division multiplexing allows multiple data streams to be sent through a single fiber independently. The present investigation aims to demonstrate a novel approach to reduce cross-talk in a three-channel RGB optical link without the need for complex optical componentry. An op-amp circuit is developed to reduce the cross-talk so that the resolution of the PWM data is preserved. An iterative Monte-Carlo simulation approach is used to optimize the op-amp circuit. The approach is developed for a set of three PWM Hall effect magnetometers with 12-bit resolution and 128 Hz sampling rate. We show that, in these conditions, the loss of resolution due to cross-talk is prevented. We also show that the cross-talk compensation allows the RGB PWM link to outperform other transmission schemes.

The theory and implementation of a high quality pulse width modulated waveform synthesiser applicable to voltage FED inverters

NASA Astrophysics Data System (ADS)

Lower, Kim Nigel

1985-03-01

Modulation processes associated with the digital implementation of pulse width modulation (PWM) switching strategies were examined. A software package based on a portable turnkey structure is presented. Waveform synthesizer implementation techniques are reviewed. A three phase PWM waveform synthesizer for voltage fed inverters was realized. It is based on a constant carrier frequency of 18 kHz and a regular sample, single edge, asynchronous PWM switching scheme. With high carrier frequencies, it is possible to utilize simple switching strategies and as a consequence, many advantages are highlighted, emphasizing the importance to industrial and office markets.

The COP9 Signalosome Converts Temporal Hormone Signaling to Spatial Restriction on Neural Competence

PubMed Central

Huang, Yi-Chun; Lu, Yu-Nung; Wu, June-Tai; Chien, Cheng-Ting; Pi, Haiwei

2014-01-01

During development, neural competence is conferred and maintained by integrating spatial and temporal regulations. The Drosophila sensory bristles that detect mechanical and chemical stimulations are arranged in stereotypical positions. The anterior wing margin (AWM) is arrayed with neuron-innervated sensory bristles, while posterior wing margin (PWM) bristles are non-innervated. We found that the COP9 signalosome (CSN) suppresses the neural competence of non-innervated bristles at the PWM. In CSN mutants, PWM bristles are transformed into neuron-innervated, which is attributed to sustained expression of the neural-determining factor Senseless (Sens). The CSN suppresses Sens through repression of the ecdysone signaling target gene broad (br) that encodes the BR-Z1 transcription factor to activate sens expression. Strikingly, CSN suppression of BR-Z1 is initiated at the prepupa-to-pupa transition, leading to Sens downregulation, and termination of the neural competence of PWM bristles. The role of ecdysone signaling to repress br after the prepupa-to-pupa transition is distinct from its conventional role in activation, and requires CSN deneddylating activity and multiple cullins, the major substrates of deneddylation. Several CSN subunits physically associate with ecdysone receptors to represses br at the transcriptional level. We propose a model in which nuclear hormone receptors cooperate with the deneddylation machinery to temporally shutdown downstream target gene expression, conferring a spatial restriction on neural competence at the PWM. PMID:25393278

Control strategy based on SPWM switching patterns for grid connected photovoltaic inverter

NASA Astrophysics Data System (ADS)

Hassaine, L.; Mraoui, A.

2017-02-01

Generally, for lower installation of photovoltaic systems connected to the grid, pulse width modulation (PWM) is a widely used technique for controlling the voltage source inverters injects currents into the grid. The current injected must be sinusoidal with reduced harmonic distortion. In this paper, a digital implementation of a control strategy based on PWM switching patterns for an inverter for photovoltaic system connected to the grid is presented. This strategy synchronize a sinusoidal inverter output current with a grid voltage The digital implementation of the proposed PWM switching pattern when is compared with the conventional one exhibit the advantage: Simplicity, reduction of the memory requirements and power calculation for the control

Implementation of Adaptive Digital Controllers on Programmable Logic Devices

NASA Technical Reports Server (NTRS)

Gwaltney, David A.; King, Kenneth D.; Smith, Keary J.; Monenegro, Justino (Technical Monitor)

2002-01-01

Much has been made of the capabilities of FPGA's (Field Programmable Gate Arrays) in the hardware implementation of fast digital signal processing. Such capability also makes an FPGA a suitable platform for the digital implementation of closed loop controllers. Other researchers have implemented a variety of closed-loop digital controllers on FPGA's. Some of these controllers include the widely used proportional-integral-derivative (PID) controller, state space controllers, neural network and fuzzy logic based controllers. There are myriad advantages to utilizing an FPGA for discrete-time control functions which include the capability for reconfiguration when SRAM-based FPGA's are employed, fast parallel implementation of multiple control loops and implementations that can meet space level radiation tolerance requirements in a compact form-factor. Generally, a software implementation on a DSP (Digital Signal Processor) or microcontroller is used to implement digital controllers. At Marshall Space Flight Center, the Control Electronics Group has been studying adaptive discrete-time control of motor driven actuator systems using digital signal processor (DSP) devices. While small form factor, commercial DSP devices are now available with event capture, data conversion, pulse width modulated (PWM) outputs and communication peripherals, these devices are not currently available in designs and packages which meet space level radiation requirements. In general, very few DSP devices are produced that are designed to meet any level of radiation tolerance or hardness. The goal of this effort is to create a fully digital, flight ready controller design that utilizes an FPGA for implementation of signal conditioning for control feedback signals, generation of commands to the controlled system, and hardware insertion of adaptive control algorithm approaches. An alternative is required for compact implementation of such functionality to withstand the harsh environment encountered on spacecraft. Radiation tolerant FPGA's are a feasible option for reaching this goal.

Implementation of Adaptive Digital Controllers on Programmable Logic Devices

NASA Technical Reports Server (NTRS)

Gwaltney, David A.; King, Kenneth D.; Smith, Keary J.; Montenegro, Justino (Technical Monitor)

2002-01-01

Much has been made of the capabilities of Field Programmable Gate Arrays (FPGA's) in the hardware implementation of fast digital signal processing functions. Such capability also makes an FPGA a suitable platform for the digital implementation of closed loop controllers. Other researchers have implemented a variety of closed-loop digital controllers on FPGA's. Some of these controllers include the widely used Proportional-Integral-Derivative (PID) controller, state space controllers, neural network and fuzzy logic based controllers. There are myriad advantages to utilizing an FPGA for discrete-time control functions which include the capability for reconfiguration when SRAM- based FPGA's are employed, fast parallel implementation of multiple control loops and implementations that can meet space level radiation tolerance requirements in a compact form-factor. Generally, a software implementation on a Digital Signal Processor (DSP) device or microcontroller is used to implement digital controllers. At Marshall Space Flight Center, the Control Electronics Group has been studying adaptive discrete-time control of motor driven actuator systems using DSP devices. While small form factor, commercial DSP devices are now available with event capture, data conversion, Pulse Width Modulated (PWM) outputs and communication peripherals, these devices are not currently available in designs and packages which meet space level radiation requirements. In general, very few DSP devices are produced that are designed to meet any level of radiation tolerance or hardness. An alternative is required for compact implementation of such functionality to withstand the harsh environment encountered on spacemap. The goal of this effort is to create a fully digital, flight ready controller design that utilizes an FPGA for implementation of signal conditioning for control feedback signals, generation of commands to the controlled system, and hardware insertion of adaptive-control algorithm approaches. Radiation tolerant FPGA's are a feasible option for reaching this goal.

Droplet size distributions of adjuvant-amended sprays from an air-assisted five-port PWM nozzle

USDA-ARS?s Scientific Manuscript database

Verification of droplet size distributions is essential for the development of real-time variable-rate sprayers that synchronize spray outputs with canopy structures. Droplet sizes from a custom-designed, air-assisted, five-port nozzle coupled with a pulse-width-modulated (PWM) solenoid valve were m...

Toward a reduced-wire readout system for ultrasound imaging.

PubMed

Lim, Jaemyung; Arkan, Evren F; Degertekin, F Levent; Ghovanloo, Maysam

2014-01-01

We present a system-on-a-chip (SoC) for use in high-frequency capacitive micromachined ultrasonic transducer (CMUT) imaging systems. This SoC consists of trans-impedance amplifiers (TIA), delay locked loop (DLL) based clock multiplier, quadrature sampler, and pulse width modulator (PWM). The SoC down converts RF echo signal to baseband by quadrature sampling which facilitates modulation. To send data through a 1.6 m wire in the catheter which has limited bandwidth and is vulnerable to noise, the SoC creates a pseudo-digital PWM signal which can be used for back telemetry or wireless readout of the RF data. In this implementation, using a 0.35-μm std. CMOS process, the TIA and single-to-differential (STD) converter had 45 MHz bandwidth, the quadrature sampler had 10.1 dB conversion gain, and the PWM had 5-bit ENoB. Preliminary results verified front-end functionality, and the power consumption of a TIA, STD, quadrature sampler, PWM, and clock multiplier was 26 mW from a 3 V supply.

Toward a Reduced-Wire Readout System for Ultrasound Imaging

PubMed Central

Lim, Jaemyung; Arkan, Evren F.; Degertekin, F. Levent; Ghovanloo, Maysam

2015-01-01

We present a system-on-a-chip (SoC) for use in high-frequency capacitive micromachined ultrasonic transducer (CMUT) imaging systems. This SoC consists of trans-impedance amplifiers (TIA), delay locked loop (DLL) based clock multiplier, quadrature sampler, and pulse width modulator (PWM). The SoC down converts RF echo signal to baseband by quadrature sampling which facilitates modulation. To send data through a 1.6 m wire in the catheter which has limited bandwidth and is vulnerable to noise, the SoC creates a pseudo-digital PWM signal which can be used for back telemetry or wireless readout of the RF data. In this implementation, using a 0.35-μm std. CMOS process, the TIA and single-to-differential (STD) converter had 45 MHz bandwidth, the quadrature sampler had 10.1 dB conversion gain, and the PWM had 5-bit ENoB. Preliminary results verified front-end functionality, and the power consumption of a TIA, STD, quadrature sampler, PWM, and clock multiplier was 26 mW from a 3 V supply. PMID:25571135

How does the interaction of presumed timing, location and extent of the underlying brain lesion relate to upper limb function in children with unilateral cerebral palsy?

PubMed

Mailleux, Lisa; Klingels, Katrijn; Fiori, Simona; Simon-Martinez, Cristina; Demaerel, Philippe; Locus, Marlies; Fosseprez, Eva; Boyd, Roslyn N; Guzzetta, Andrea; Ortibus, Els; Feys, Hilde

2017-09-01

Upper limb (UL) function in children with unilateral cerebral palsy (CP) vary largely depending on presumed timing, location and extent of brain lesions. These factors might exhibit a complex interaction and the combined prognostic value warrants further investigation. This study aimed to map lesion location and extent and assessed whether these differ according to presumed lesion timing and to determine the impact of structural brain damage on UL function within different lesion timing groups. Seventy-three children with unilateral CP (mean age 10 years 2 months) were classified according to lesion timing: malformations (N = 2), periventricular white matter (PWM, N = 42) and cortical and deep grey matter (CDGM, N = 29) lesions. Neuroanatomical damage was scored using a semi-quantitative MRI scale. UL function was assessed at body function and activity level. CDGM lesions were more pronounced compared to PWM lesions (p = 0.0003). Neuroanatomical scores were correlated with a higher degree to UL function in the CDGM group (r s  = -0.39 to r s  = -0.84) compared to the PWM group (r rb  = -0.42 to r s  = -0.61). Regression analysis found lesion location and extent to explain 75% and 65% (p < 0.02) respectively, of the variance in AHA performance in the CDGM group, but only 24% and 12% (p < 0.03) in the PWM group. In the CDGM group, lesion location and extent seems to impact more on UL function compared to the PWM group. In children with PWM lesions, other factors like corticospinal tract (re)organization and structural connectivity may play an additional role. Copyright © 2017 European Paediatric Neurology Society. All rights reserved.

Performance optimization of a photovoltaic chain conversion by the PWM control

NASA Astrophysics Data System (ADS)

Rezoug, M. R.; Chenni, R.

2017-02-01

The interest of the research technique of maximum power point tracking, exposed by this article, lays in the fact of work instantly on the real characteristic of the photovoltaic module. This work is based on instantaneous measurements of its terminals' current & voltage as well as the exploitation of the characteristic "Power - Duty Cycle" to define rapidly the Duty cycle in which power reaches its maximum value. To ensure instantaneous tracking of the point of maximum power, we use "DC/DC Converter" based on "Pulse Wave Modulation's (PWM) Command" controlled by an algorithm implanted in a microcontroller's memory. This algorithm responds to the quick changes in climate (sunlight and temperature). To identify the control parameters "VPV & IPV" at any change in operating conditions, sensors are projected. this algorithm applied to the Duty cycle of the static converter enables the control of power supplied by the photovoltaic generator thanks to oscillatory movement around the MPP. Our article highlights the importance of this technique which lays in its simplicity and performance in changing climatic conditions. This efficiency is confirmed by experimental tests and this technique will improve its predecessors.

Electromagnetic phenomena analysis in brushless DC motor with speed control using PWM method

NASA Astrophysics Data System (ADS)

Ciurys, Marek Pawel

2017-12-01

Field-circuit model of a brushless DC motor with speed control using PWM method was developed. Waveforms of electrical and mechanical quantities of the designed motor with a high pressure vane pump built in a rotor of the motor were computed. Analysis of electromagnetic phenomena in the system: single phase AC network - converter - BLDC motor was carried out.

A dual slope charge sampling analog front-end for a wireless neural recording system.

PubMed

Lee, Seung Bae; Lee, Byunghun; Gosselin, Benoit; Ghovanloo, Maysam

2014-01-01

This paper presents a novel dual slope charge sampling (DSCS) analog front-end (AFE) architecture, which amplifies neural signals by taking advantage of the charge sampling concept for analog signal conditioning, such as amplification and filtering. The presented DSCS-AFE achieves amplification, filtering, and sampling in a simultaneous fashion, while consuming very small amount of power. The output of the DSCS-AFE produces a pulse width modulated (PWM) signal that is proportional to the input voltage amplitude. A circular shift register (CSR) utilizes time division multiplexing (TDM) of the PWM pulses to create a pseudo-digital TDM-PWM signal that can feed a wireless transmitter. The 8-channel system-on-a-chip was fabricated in a 0.35-μm CMOS process, occupying 2.4 × 2.1 mm(2) and consuming 255 μW from a 1.8V supply. Measured input-referred noise for the entire system, including the FPGA in order to recover PWM signal is 6.50 μV(rms) in the 288 Hz~10 kHz range. For each channel, sampling rate is 31.25 kHz, and power consumption is 31.8 μW.

A Dual Slope Charge Sampling Analog Front-End for a Wireless Neural Recording System

PubMed Central

Lee, Seung Bae; Lee, Byunghun; Gosselin, Benoit

2015-01-01

This paper presents a novel dual slope charge sampling (DSCS) analog front-end (AFE) architecture, which amplifies neural signals by taking advantage of the charge sampling concept for analog signal conditioning, such as amplification and filtering. The presented DSCS-AFE achieves amplification, filtering, and sampling in a simultaneous fashion, while consuming very small amount of power. The output of the DSCS-AFE produces a pulse width modulated (PWM) signal that is proportional to the input voltage amplitude. A circular shift register (CSR) utilizes time division multiplexing (TDM) of the PWM pulses to create a pseudo-digital TDM-PWM signal that can feed a wireless transmitter. The 8-channel system-on-a-chip was fabricated in a 0.35-µm CMOS process, occupying 2.4 × 2.1 mm2 and consuming 255 µW from a 1.8V supply. Measured input-referred noise for the entire system, including the FPGA in order to recover PWM signal is 6.50 µVrms in the 288 Hz~10 kHz range. For each channel, sampling rate is 31.25 kHz, and power consumption is 31.8 µW. PMID:25570655

Enhancement of mosquito trapping efficiency by using pulse width modulated light emitting diodes.

PubMed

Liu, Yu-Nan; Liu, Yu-Jen; Chen, Yi-Chian; Ma, Hsin-Yi; Lee, Hsiao-Yi

2017-01-06

In this study, a light-driving bug zapper is presented for well controlling the diseases brought by insects, such as mosquitoes. In order to have the device efficient to trap the insect pests in off-grid areas, pulse width modulated light emitting diodes (PWM-LED) combined with a solar power module are proposed and implemented. With specific PWM electric signals to drive the LED, it is found that no matter what the ability of catching insects or the consumed power efficiency can be enhanced thus. It is demonstrated that 40% of the UV LED consumed power and 25.9% of the total load power consumption can be saved, and the trapped mosquitoes are about 250% increased when the PWM method is applied in the bug zapper experiments.

Enhancement of mosquito trapping efficiency by using pulse width modulated light emitting diodes

NASA Astrophysics Data System (ADS)

Liu, Yu-Nan; Liu, Yu-Jen; Chen, Yi-Chian; Ma, Hsin-Yi; Lee, Hsiao-Yi

2017-01-01

In this study, a light-driving bug zapper is presented for well controlling the diseases brought by insects, such as mosquitoes. In order to have the device efficient to trap the insect pests in off-grid areas, pulse width modulated light emitting diodes (PWM-LED) combined with a solar power module are proposed and implemented. With specific PWM electric signals to drive the LED, it is found that no matter what the ability of catching insects or the consumed power efficiency can be enhanced thus. It is demonstrated that 40% of the UV LED consumed power and 25.9% of the total load power consumption can be saved, and the trapped mosquitoes are about 250% increased when the PWM method is applied in the bug zapper experiments.

Operation of a voltage source converter at increased utility voltage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaura, V.; Blasko, V.

1997-01-01

The operation of a voltage source converter (VSC) with regeneration capability, controllable power factor, and low distortion of utility currents is analyzed at increased utility voltage. Increase in the utility voltage causes a VSC to saturate and enter a nonlinear mode of operation. To operate under elevated utility, two steps are taken: (1) a pulse width modulation (PWM) algorithm is implemented which extends the linear region of operation by 15% and (2) a PWM saturation regulator is used to control the reactive current at higher utility voltages. The PWM algorithm reduces the switching losses by at least 33% and themore » effect of blanking time by one-third. All analytical results are experimentally verified on a 100 kW three-phase VSC.« less

Enhancement of mosquito trapping efficiency by using pulse width modulated light emitting diodes

PubMed Central

Liu, Yu-Nan; Liu, Yu-Jen; Chen, Yi-Chian; Ma, Hsin-Yi; Lee, Hsiao-Yi

2017-01-01

In this study, a light-driving bug zapper is presented for well controlling the diseases brought by insects, such as mosquitoes. In order to have the device efficient to trap the insect pests in off-grid areas, pulse width modulated light emitting diodes (PWM-LED) combined with a solar power module are proposed and implemented. With specific PWM electric signals to drive the LED, it is found that no matter what the ability of catching insects or the consumed power efficiency can be enhanced thus. It is demonstrated that 40% of the UV LED consumed power and 25.9% of the total load power consumption can be saved, and the trapped mosquitoes are about 250% increased when the PWM method is applied in the bug zapper experiments. PMID:28059148

Compact pulse width modulation circuitry for silicon photomultiplier readout.

PubMed

Bieniosek, M F; Olcott, P D; Levin, C S

2013-08-07

The adoption of solid-state photodetectors for positron emission tomography (PET) system design and the interest in 3D interaction information from PET detectors has lead to an increasing number of readout channels in PET systems. To handle these additional readout channels, PET readout electronics should be simplified to reduce the power consumption, cost, and size of the electronics for a single channel. Pulse-width modulation (PWM), where detector pulses are converted to digital pulses with width proportional to the detected photon energy, promises to simplify PET readout by converting the signals to digital form at the beginning of the processing chain, and allowing a single time-to-digital converter to perform the data acquisition for many channels rather than routing many analogue channels and digitizing in the back end. Integrator based PWM systems, also known as charge-to-time converters (QTCs), are especially compact, reducing the front-end electronics to an op-amp integrator with a resistor discharge, and a comparator. QTCs, however, have a long dead-time during which dark count noise is integrated, reducing the output signal-to-noise ratio. This work presents a QTC based PWM circuit with a gated integrator that shows performance improvements over existing QTC based PWM. By opening and closing an analogue switch on the input of the integrator, the circuit can be controlled to integrate only the portions of the signal with a high signal-to-noise ratio. It also allows for multiplexing different detectors into the same PWM circuit while avoiding uncorrelated noise propagation between photodetector channels. Four gated integrator PWM circuits were built to readout the spatial channels of two position sensitive solid-state photomultiplier (PS-SSPM). Results show a 4 × 4 array 0.9 mm × 0.9 mm × 15 mm of LYSO crystals being identified on the 5 mm × 5 mm PS-SSPM at room temperature with no degradation for twofold multiplexing. In principle, much larger multiplexing ratios are possible, limited only by count rate issues.

The Design of Connection Solid Oxide Fuel Cell (SOFC) Integrated Grid with Three-Phase Inverter

NASA Astrophysics Data System (ADS)

Darjat; Sulistyo; Triwiyatno, Aris; Thalib, Humaid

2018-03-01

Fuel cell technology is a relatively new energy-saving technology that has the potential to replace conventional energy technologies. Among the different types of generation technologies, fuel cells is the generation technologies considered as a potential source of power generation because it is flexible and can be placed anywhere based distribution system. Modeling of SOFC is done by using Nernst equation. The output power of the fuel cell can be controlled by controlling the flow rate of the fuels used in the process. Three-phase PWM inverter is used to get the form of three-phase voltage which same with the grid. In this paper, the planning and design of the SOFC are connected to the grid.

Similar disturbances in B cell activity and regulatory T cell function in Henoch-Schonlein purpura and systemic lupus erythematosus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beale, M.G.; Nash, G.S.; Bertovich, M.J.

1982-01-01

The immunoglobulin synthesizing activities of peripheral mononuclear cells (MNC) from five patients with Henoch-Schonlein purpura (HSP) and eight patients with active systemic lupus erythematosus (SLE) were compared. Cumulative amounts of IgM, IgG, and IgA synthesized and secreted by unstimulated and PWM-stimulated patient cells over a 12-day period were determied in a solid-phase radioimmunoassay. In unstimulated control cultures mean rates of IgM, IgG, and IgA synthesis were less than 250 ng/ml. The synthetic activities of patient MNC were markedly increased. In HSP cultures IgA was the major immunoglobulin class produced (2810 x/divide 1.33 ng/ml) followed by IgG (1754 x/divide 1.32 ng/ml)more » and IgM (404 x/divide 1.16 ng/ml). In SLE cultures IgA and IgG syntheses were equally elevated (4427 x/divide 1.20 and 4438 x/divide 1.49 ng/ml, respectively) whereas IgM synthesis averaged 967 x/divide 1.66 ng/ml. PWM stimulation of pateient MNC caused a sharp decline in the synthesis of all three immunoglobulin classes. After T cell depletion B cell-enriched fractions from HSP and SLE patients maintained high levels of IgA and IgG synthesis that were inhibited by PWM and by normal allogeneic but not autologous T cells. In PWM-stimulted co-cultures, patient T cells nonspecifically suppressed the synthetic activities of autologous and control B cells. in contrast patient B cells achieved normal levels of immunoglobulin synthesis when cultured with control T cells plus PWM. In longitudinal studies patient B and T cell disturbances persisted despite clinical improvement.« less

Development of ATC for High Speed and High Density Commuter Line

NASA Astrophysics Data System (ADS)

Okutani, Tamio; Nakamura, Nobuyuki; Araki, Hisato; Irie, Shouji; Osa, Hiroki; Sano, Minoru; Ikeda, Keigo; Ozawa, Hiroyuki

A new ATC (Automatic Train Control) system has been developed with solutions to realize short train headway by assured braking utilizing digital data transmission via rails; the digital data for the ATP (Automatic Train Protection) function; and to achieve EMC features for both AC and DC sections. The DC section is of the unprecedented DC traction power supply system utilizing IGBT PWM converter at all DC substations. Within the AC section, train traction force is controlled by PWM converter/inverters. The carrier frequencies of the digital data signals and chopping frequency of PWM traction power converters on-board are decided via spectral analysis of noise up to degraded mode cases of equipment. Developed system was equipped to the Tukuba Express Line, new commuter line of Tokyo metropolitan area, and opened since Aug. 2005.

An improved fault-tolerant control scheme for PWM inverter-fed induction motor-based EVs.

PubMed

Tabbache, Bekheïra; Benbouzid, Mohamed; Kheloui, Abdelaziz; Bourgeot, Jean-Matthieu; Mamoune, Abdeslam

2013-11-01

This paper proposes an improved fault-tolerant control scheme for PWM inverter-fed induction motor-based electric vehicles. The proposed strategy deals with power switch (IGBTs) failures mitigation within a reconfigurable induction motor control. To increase the vehicle powertrain reliability regarding IGBT open-circuit failures, 4-wire and 4-leg PWM inverter topologies are investigated and their performances discussed in a vehicle context. The proposed fault-tolerant topologies require only minimum hardware modifications to the conventional off-the-shelf six-switch three-phase drive, mitigating the IGBTs failures by specific inverter control. Indeed, the two topologies exploit the induction motor neutral accessibility for fault-tolerant purposes. The 4-wire topology uses then classical hysteresis controllers to account for the IGBT failures. The 4-leg topology, meanwhile, uses a specific 3D space vector PWM to handle vehicle requirements in terms of size (DC bus capacitors) and cost (IGBTs number). Experiments on an induction motor drive and simulations on an electric vehicle are carried-out using a European urban driving cycle to show that the proposed fault-tolerant control approach is effective and provides a simple configuration with high performance in terms of speed and torque responses. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Design of PID temperature control system based on STM32

NASA Astrophysics Data System (ADS)

Zhang, Jianxin; Li, Hailin; Ma, Kai; Xue, Liang; Han, Bianhua; Dong, Yuemeng; Tan, Yue; Gu, Chengru

2018-03-01

A rapid and high-accuracy temperature control system was designed using proportional-integral-derivative (PID) control algorithm with STM32 as micro-controller unit (MCU). The temperature control system can be applied in the fields which have high requirements on the response speed and accuracy of temperature control. The temperature acquisition circuit in system adopted Pt1000 resistance thermometer as temperature sensor. Through this acquisition circuit, the monitoring actual temperature signal could be converted into voltage signal and transmitted into MCU. A TLP521-1 photoelectric coupler was matched with BD237 power transistor to drive the thermoelectric cooler (TEC) in FTA951 module. The effective electric power of TEC was controlled by the pulse width modulation (PWM) signals which generated by MCU. The PWM signal parameters could be adjusted timely by PID algorithm according to the difference between monitoring actual temperature and set temperature. The upper computer was used to input the set temperature and monitor the system running state via serial port. The application experiment results show that the temperature control system is featured by simple structure, rapid response speed, good stability and high temperature control accuracy with the error less than ±0.5°C.

Investigating the role of implicit prototypes in the prototype willingness model.

PubMed

Howell, Jennifer L; Ratliff, Kate A

2017-06-01

One useful theory to predict health behavior is the prototype-willingness model (PWM), which posits that people are more willing to engage in behavior to the extent that they have a positive view of the prototypical person who performs that behavior. The goal of the present research is to test whether adding an implicit measure of prototype favorability might improve explanatory power in the PWM. Two studies examined whether implicit prototype favorability uniquely predicted White women's intentions to engage in healthy sun behavior over the next 3-6 months, and their willingness to engage in risky sun behavior, should the opportunity arise. The results suggested that implicit prototype favorability, particularly implicit prototypes of those who engage in risky UV-related behaviors, uniquely predicted intentions to engage in healthy sun behavior and willingness to engage in risky sun behavior in the PWM.

The simulation on diode-clamped five-level converters common-mode voltage suppression with zero-vector PWM strategy

NASA Astrophysics Data System (ADS)

Zhang, Yonggao; Gao, Yanli; Long, Lizhong

2012-04-01

More and more researchers have great concern on the issue of Common-mode voltage (CMV) in high voltage large power converter. A novel common-mode voltage suppression scheme based on zero-vector PWM strategy (ZVPWM) is present in this paper. Taking a diode-clamped five-level converter as example, the principle of zero vector PWM common-mode voltage (ZCMVPWM) suppression method is studied in detail. ZCMVPWM suppression strategy is including four important parts, which are locating the sector of reference voltage vector, locating the small triangular sub-sector of reference voltage vector, reference vector synthesis, and calculating the operating time of vector. The principles of four important pars are illustrated in detail and the corresponding MATLAB models are established. System simulation and experimental results are provided. It gives some consultation value for the development and research of multi-level converters.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacobina, C.B.; Silva, E.R.C. da; Lima, A.M.N.

This paper investigates the PWM operation of a four switch three phase inverter (FSTPI), in the case of digital implementation. Different switching sequence strategies for vector control are described and a digital scalar method is also presented. The influence of different switching patterns on the output voltage symmetry, current waveform and switching frequency are examined. The results obtained by employing the vector and scalar strategies are compared and a relationship between them is established. This comparison is based on analytical study and is corroborated either by the computer simulations and by the experimental results. The vector approach makes ease themore » understanding and analysis of the FSTPI, as well the choice of a PWM pattern. However, similar results may be obtained through the scalar approach, which has a simpler implementation. The experimental results of the use of the FSTPI and digital PWM to control an induction motor are presented.« less

A high efficiency PWM CMOS class-D audio power amplifier

NASA Astrophysics Data System (ADS)

Zhangming, Zhu; Lianxi, Liu; Yintang, Yang; Han, Lei

2009-02-01

Based on the difference close-loop feedback technique and the difference pre-amp, a high efficiency PWM CMOS class-D audio power amplifier is proposed. A rail-to-rail PWM comparator with window function has been embedded in the class-D audio power amplifier. Design results based on the CSMC 0.5 μm CMOS process show that the max efficiency is 90%, the PSRR is -75 dB, the power supply voltage range is 2.5-5.5 V, the THD+N in 1 kHz input frequency is less than 0.20%, the quiescent current in no load is 2.8 mA, and the shutdown current is 0.5 μA. The active area of the class-D audio power amplifier is about 1.47 × 1.52 mm2. With the good performance, the class-D audio power amplifier can be applied to several audio power systems.

High-frequency AC/DC converter with unity power factor and minimum harmonic distortion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wernekinch, E.R.

1987-01-01

The power factor is controlled by adjusting the relative position of the fundamental component of an optimized PWM-type voltage with respect to the supply voltage. Current harmonic distortion is minimized by the use of optimized firing angles for the converter at a frequency where GTO's can be used. This feature makes this approach very attractive at power levels of 100 to 600 kW. To obtain the optimized PWM pattern, a steepest descent digital computer algorithm is used. Digital-computer simulations are performed and a low-power model is constructed and tested to verify the concepts and the behavior of the model. Experimentalmore » results show that unity power factor is achieved and that the distortion in the phase currents is 10.4% at 90% of full load. This is less than achievable with sinusoidal PWM, harmonic elimination, hysteresis control, and deadbeat control for the same switching frequency.« less

Embedded system based on PWM control of hydrogen generator with SEPIC converter

NASA Astrophysics Data System (ADS)

Fall, Cheikh; Setiawan, Eko; Habibi, Muhammad Afnan; Hodaka, Ichijo

2017-09-01

The objective of this paper is to design and to produce a micro electrical plant system based on fuel cell for teaching material-embedded systems in technical vocational training center. Based on this, the student can experience generating hydrogen by fuel cells, controlling the rate of hydrogen generation by the duty ration of single-ended primary-inductor converter(SEPIC), drawing the curve rate of hydrogen to duty ratio, generating electrical power by using hydrogen, and calculating the fuel cell efficiency when it is used as electrical energy generator. This project is of great importance insofar as students will need to acquire several skills to be able to realize it such as continuous DC DC conversion and the scientific concept behind the converter, the regulation of systems with integral proportional controllers, the installation of photovoltaic cells, the use of high-tech sensors, microcontroller programming, object-oriented programming, mastery of the fuel cell syste

Highly Sensitive Temperature Sensors Based on Fiber-Optic PWM and Capacitance Variation Using Thermochromic Sensing Membrane.

PubMed

Khan, Md Rajibur Rahaman; Kang, Shin-Won

2016-07-09

In this paper, we propose a temperature/thermal sensor that contains a Rhodamine-B sensing membrane. We applied two different sensing methods, namely, fiber-optic pulse width modulation (PWM) and an interdigitated capacitor (IDC)-based temperature sensor to measure the temperature from 5 °C to 100 °C. To the best of our knowledge, the fiber-optic PWM-based temperature sensor is reported for the first time in this study. The proposed fiber-optic PWM temperature sensor has good sensing ability; its sensitivity is ~3.733 mV/°C. The designed temperature-sensing system offers stable sensing responses over a wide dynamic range, good reproducibility properties with a relative standard deviation (RSD) of ~0.021, and the capacity for a linear sensing response with a correlation coefficient of R² ≈ 0.992 over a wide sensing range. In our study, we also developed an IDC temperature sensor that is based on the capacitance variation principle as the IDC sensing element is heated. We compared the performance of the proposed temperature-sensing systems with different fiber-optic temperature sensors (which are based on the fiber-optic wavelength shift method, the long grating fiber-optic Sagnac loop, and probe type fiber-optics) in terms of sensitivity, dynamic range, and linearity. We observed that the proposed sensing systems have better sensing performance than the above-mentioned sensing system.

Filtering and Control of High Speed Motor Current in a Flywheel Energy Storage System

NASA Technical Reports Server (NTRS)

Kenny, Barbara H.; Santiago, Walter

2004-01-01

The NASA Glenn Research Center has been developing technology to enable the use of high speed flywheel energy storage units in future spacecraft for the last several years. An integral part of the flywheel unit is the three phase motor/generator that is used to accelerate and decelerate the flywheel. The motor/generator voltage is supplied from a pulse width modulated (PWM) inverter operating from a fixed DC voltage supply. The motor current is regulated through a closed loop current control that commands the necessary voltage from the inverter to achieve the desired current. The current regulation loop is the innermost control loop of the overall flywheel system and, as a result, must be fast and accurate over the entire operating speed range (20,000 to 60,000 rpm) of the flywheel. The voltage applied to the motor is a high frequency PWM version of the DC bus voltage that results in the commanded fundamental value plus higher order harmonics. Most of the harmonic content is at the switching frequency and above. The higher order harmonics cause a rapid change in voltage to be applied to the motor that can result in large voltage stresses across the motor windings. In addition, the high frequency content in the motor causes sensor noise in the magnetic bearings that leads to disturbances for the bearing control. To alleviate these problems, a filter is used to present a more sinusoidal voltage to the motor/generator. However, the filter adds additional dynamics and phase lag to the motor system that can interfere with the performance of the current regulator. This paper will discuss the tuning methodology and results for the motor/generator current regulator and the impact of the filter on the control. Results at speeds up to 50,000 rpm are presented.

Implicit alcohol attitudes predict drinking behaviour over and above intentions and willingness in young adults but willingness is more important in adolescents: Implications for the Prototype Willingness Model.

PubMed

Davies, Emma L; Paltoglou, Aspasia E; Foxcroft, David R

2017-05-01

Dual process models, such as the Prototype Willingness Model (PWM), propose to account for both intentional and reactive drinking behaviour. Current methods of measuring constructs in the PWM rely on self-report, thus require a level of conscious deliberation. Implicit measures of attitudes may overcome this limitation and contribute to our understanding of how prototypes and willingness influence alcohol consumption in young people. This study aimed to explore whether implicit alcohol attitudes were related to PWM constructs and whether they would add to the prediction of risky drinking. The study involved a cross-sectional design. The sample included 501 participants from the United Kingdom (M age 18.92; range 11-51; 63% female); 230 school pupils and 271 university students. Participants completed explicit measures of alcohol prototype perceptions, willingness, drunkenness, harms, and intentions. They also completed an implicit measure of alcohol attitudes, using the Implicit Association Test. Implicit alcohol attitudes were only weakly related to the explicit measures. When looking at the whole sample, implicit alcohol attitudes did not add to the prediction of willingness over and above prototype perceptions. However, for university students implicit attitudes added to the prediction of behaviour, over and above intentions and willingness. For school pupils, willingness was a stronger predictor of behaviour than intentions or implicit attitudes. Adding implicit measures to the PWM may contribute to our understanding of the development of alcohol behaviours in young people. Further research could explore how implicit attitudes develop alongside the shift from reactive to planned behaviour. Statement of contribution What is already known on this subject? Young people's drinking tends to occur in social situations and is driven in part by social reactions within these contexts. The Prototype Willingness Model (PWM) attempts to explain such reactive behaviour as the result of social comparison to risk prototypes, which influence willingness to drink, and subsequent behaviour. Evidence also suggests that risky drinking in young people may be influenced by implicit attitudes towards alcohol, which develop with repeated exposure to alcohol over time. One criticism of the PWM is that prototypes and willingness are usually measured using explicit measures which may not adequately capture young people's spontaneous evaluations of prototypes, or their propensity to act without forethought in a social context. What does this study add? This study is novel in exploring the addition of implicit alcohol attitudes to the social reaction pathway in the model in order to understand more about these reactive constructs. Implicit alcohol attitudes added to the prediction of behaviour, over and above intentions and willingness for university students. For school pupils, willingness was a stronger predictor of behaviour than intentions or implicit attitudes. Findings suggest that adding implicit alcohol attitudes into the PWM might be able to explain the shift from reactive to intentional drinking behaviours with age and experience. © 2016 The British Psychological Society.

A PWM Buck Converter With Load-Adaptive Power Transistor Scaling Scheme Using Analog-Digital Hybrid Control for High Energy Efficiency in Implantable Biomedical Systems.

PubMed

Park, Sung-Yun; Cho, Jihyun; Lee, Kyuseok; Yoon, Euisik

2015-12-01

We report a pulse width modulation (PWM) buck converter that is able to achieve a power conversion efficiency (PCE) of > 80% in light loads 100 μA) for implantable biomedical systems. In order to achieve a high PCE for the given light loads, the buck converter adaptively reconfigures the size of power PMOS and NMOS transistors and their gate drivers in accordance with load currents, while operating at a fixed frequency of 1 MHz. The buck converter employs the analog-digital hybrid control scheme for coarse/fine adjustment of power transistors. The coarse digital control generates an approximate duty cycle necessary for driving a given load and selects an appropriate width of power transistors to minimize redundant power dissipation. The fine analog control provides the final tuning of the duty cycle to compensate for the error from the coarse digital control. The mode switching between the analog and digital controls is accomplished by a mode arbiter which estimates the average of duty cycles for the given load condition from limit cycle oscillations (LCO) induced by coarse adjustment. The fabricated buck converter achieved a peak efficiency of 86.3% at 1.4 mA and > 80% efficiency for a wide range of load conditions from 45 μA to 4.1 mA, while generating 1 V output from 2.5-3.3 V supply. The converter occupies 0.375 mm(2) in 0.18 μm CMOS processes and requires two external components: 1.2 μF capacitor and 6.8 μH inductor.

Improving dynamic performances of PWM-driven servo-pneumatic systems via a novel pneumatic circuit.

PubMed

Taghizadeh, Mostafa; Ghaffari, Ali; Najafi, Farid

2009-10-01

In this paper, the effect of pneumatic circuit design on the input-output behavior of PWM-driven servo-pneumatic systems is investigated and their control performances are improved using linear controllers instead of complex and costly nonlinear ones. Generally, servo-pneumatic systems are well known for their nonlinear behavior. However, PWM-driven servo-pneumatic systems have the advantage of flexibility in the design of pneumatic circuits which affects the input-output linearity of the whole system. A simple pneumatic circuit with only one fast switching valve is designed which leads to a quasi-linear input-output relation. The quasi-linear behavior of the proposed circuit is verified both experimentally and by simulations. Closed loop position control experiments are then carried out using linear P- and PD-controllers. Since the output position is noisy and cannot be directly differentiated, a Kalman filter is designed to estimate the velocity of the cylinder. Highly improved tracking performances are obtained using these linear controllers, compared to previous works with nonlinear controllers.

Ontogeny of surface markers on functionally distinct T cell subsets in the chicken.

PubMed

Traill, K N; Böck, G; Boyd, R L; Ratheiser, K; Wick, G

1984-01-01

Three subsets of chicken peripheral T cells (T1, T2 and T3) have been identified in peripheral blood of adult chickens on the basis of fluorescence intensity after staining with certain xenogeneic anti-thymus cell sera (from turkeys and rabbits). They differentiate between 3-10 weeks of age in parallel with development of responsiveness to the mitogens concanavalin A (Con A), phytohemagglutinin (PHA) and pokeweed mitogen (PWM). Functional tests on the T subsets, sorted with a fluorescence-activated cell sorter, have shown that T2, 3 cells respond to Con A, PHA and PWM and are capable of eliciting a graft-vs.-host reaction (GvHR). In contrast, although T1 cells respond to Con A, they respond poorly to PHA and not at all to PWM or in GvHR. There was some indication of cooperation between T1 and T2,3 cells for the PHA response. Parallels between these chicken subsets and helper and suppressor/cytotoxic subsets in mammalian systems are discussed.

Solar power generation system for reducing leakage current

NASA Astrophysics Data System (ADS)

Wu, Jinn-Chang; Jou, Hurng-Liahng; Hung, Chih-Yi

2018-04-01

This paper proposes a transformer-less multi-level solar power generation system. This solar power generation system is composed of a solar cell array, a boost power converter, an isolation switch set and a full-bridge inverter. A unipolar pulse-width modulation (PWM) strategy is used in the full-bridge inverter to attenuate the output ripple current. Circuit isolation is accomplished by integrating the isolation switch set between the solar cell array and the utility, to suppress the leakage current. The isolation switch set also determines the DC bus voltage for the full-bridge inverter connecting to the solar cell array or the output of the boost power converter. Accordingly, the proposed transformer-less multi-level solar power generation system generates a five-level voltage, and the partial power of the solar cell array is also converted to AC power using only the full-bridge inverter, so the power efficiency is increased. A prototype is developed to validate the performance of the proposed transformer-less multi-level solar power generation system.

A PWM Controller of a Full Bridge Single-Phase Synchronous Inverter for Micro-Grid System

NASA Astrophysics Data System (ADS)

Rahman, Tawfikur; Motakabber, S. M. A.; Ibrahimy, M. I.; Raghib, Aliza ‘Aini Binti Md Ralib@ Md

2017-12-01

Nowadays, microgrid system technology is becoming popular for small area power management systems. It is essential to be less harmonic-distortion and high efficiency of the inverter for microgrid applications. Pulse width modulation (PWM) controller is a conventional switching control technique which is suitable to use in the microgrid connected power inverter system. The control method and algorithm of this technique are challenging, and different approaches are required to avoid the complexity for a customized solution of the microgrid application. This paper proposes a comparative analysis of different controller and their operational methods. A PWM controller is used to reduce the ripple voltage noise while a continuous current mode provides a small output ripple which gives steady-state error as zero on fundamental and cutoff frequency. To reduce the ripple current, higher frequency harmonic distortion, switching loss and phase noise, LC low pass filter is used on either side of input and output terminals. The proposed inverter is designed by MATLAB 2016a simulation software. A balanced load resistance (RL = 20.5 Ω) of star configuration and a dual input DC voltage of ± 35V are considered. In this design, the circuit parameters, the fundamental frequency of 50 Hz, the PWM duty cycle of 95%, the cutoff frequency of the switching controller of 33 kHz are considered. The inverter in this paper exhibits THD of 0.44% and overall efficiency approximately of 98%. The proposed inverter is expected to be suitable for microgrid applications.

Establishment of the Pediatric Obesity Weight Evaluation Registry: A National Research Collaborative for Identifying the Optimal Assessment and Treatment of Pediatric Obesity.

PubMed

Kirk, Shelley; Armstrong, Sarah; King, Eileen; Trapp, Christine; Grow, Mollie; Tucker, Jared; Joseph, Madeline; Liu, Lenna; Weedn, Ashley; Sweeney, Brooke; Fox, Claudia; Fathima, Samreen; Williams, Ronald; Kim, Roy; Stratbucker, William

2017-02-01

Prospective patient registries have been successfully utilized in several disease states with a goal of improving treatment approaches through multi-institutional collaboration. The prevalence of youth with severe obesity is at a historic high in the United States, yet evidence to guide effective weight management is limited. The Pediatric Obesity Weight Evaluation Registry (POWER) was established in 2013 to identify and promote effective intervention strategies for pediatric obesity. Sites in POWER provide multicomponent pediatric weight management (PWM) care for youth with obesity and collect a defined set of demographic and clinical parameters, which they regularly submit to the POWER Data Coordinating Center. A program profile survey was completed by sites to describe characteristics of the respective PWM programs. From January 2014 through December 2015, 26 US sites were enrolled in POWER and had submitted data on 3643 youth with obesity. Ninety-five percent were 6-18 years of age, 54% female, 32% nonwhite, 32% Hispanic, and 59% publicly insured. Over two-thirds had severe obesity. All sites included a medical provider and used weight status in their referral criteria. Other program characteristics varied widely between sites. POWER is an established national registry representing a diverse sample of youth with obesity participating in multicomponent PWM programs across the United States. Using high-quality data collection and a collaborative research infrastructure, POWER aims to contribute to the development of evidence-based guidelines for multicomponent PWM programs.

A Spacecraft Housekeeping System-on-Chip in a Radiation Hardened Structured ASIC

NASA Technical Reports Server (NTRS)

Suarez, George; DuMonthier, Jeffrey J.; Sheikh, Salman S.; Powell, Wesley A.; King, Robyn L.

2012-01-01

Housekeeping systems are essential to health monitoring of spacecraft and instruments. Typically, sensors are distributed across various sub-systems and data is collected using components such as analog-to-digital converters, analog multiplexers and amplifiers. In most cases programmable devices are used to implement the data acquisition control and storage, and the interface to higher level systems. Such discrete implementations require additional size, weight, power and interconnect complexity versus an integrated circuit solution, as well as the qualification of multiple parts. Although commercial devices are readily available, they are not suitable for space applications due the radiation tolerance and qualification requirements. The Housekeeping System-o n-A-Chip (HKSOC) is a low power, radiation hardened integrated solution suitable for spacecraft and instrument control and data collection. A prototype has been designed and includes a wide variety of functions including a 16-channel analog front-end for driving and reading sensors, analog-to-digital and digital-to-analog converters, on-chip temperature sensor, power supply current sense circuits, general purpose comparators and amplifiers, a 32-bit processor, digital I/O, pulse-width modulation (PWM) generators, timers and I2C master and slave serial interfaces. In addition, the device can operate in a bypass mode where the processor is disabled and external logic is used to control the analog and mixed signal functions. The device is suitable for stand-alone or distributed systems where multiple chips can be deployed across different sub-systems as intelligent nodes with computing and processing capabilities.

T cell-replacing factor for glucocorticosteroid-induced immunoglobulin production. A unique steroid-dependent cytokine

PubMed Central

1983-01-01

Glucocorticosteroids (GCS) added to otherwise unstimulated cultures of human peripheral blood mononuclear cells (PBMC) induce the synthesis and secretion of all classes of immunoglobulin. The magnitude of this response is similar to that seen with other polyclonal B cell activators such as pokeweed mitogen (PWM), and like that of PWM, the steroid effect is dependent on both T cells and monocytes. To determine the cellular target for GCS in these cultures, separated populations of T cells and non-T cells were preincubated with steroids and then recombined. No immunoglobulin was produced in any of these preincubation experiments. As a different approach to this question, supernatants were collected from various cell populations following stimulation with PWM, concanavalin A (Con A), phytohemagglutinin (PHA), alloantigens, or GCS. These supernatants were tested for their effects on GCS-induced Ig production by B cells. Supernatants from 3-d cultures of unstimulated, as well as GCS-treated, PBMC contained a T cell- replacing factor that permitted T-depleted PBMC to produce Ig upon steroid stimulation. This supernatant factor (TRF-S) could be produced in the absence of steroid stimulation, but both the factor and GCS were necessary for the induction of Ig synthesis. Production of the TRF-S required the presence of both T cells and adherent cells in culture and was found in the highest concentrations at 3-4 d of culture. Supernatants from cultures stimulated with PWM, PHA, Con A, and alloantigens did not contain detectable TRF-S activity, and TRF-S was unable to replace helper T cells for PWM-induced Ig production. TRF-S required the presence of adherent cells in the T cell-depleted responder population for its action. Further, it was effective in inducing Ig production along with GCS in the presence of a sufficient concentration of cyclosporin A to block all T cell helper activity for primary responses of PBMC to PWM or GCS. TRF-S was inactivated by trypsin treatment, heating to 56 degrees C, freezing, lyophilization, and storage at 4 degrees C for greater than 3 wk. Its molecular weight is probably 10,000 daltons or more, since TRF-S activity is not rapidly dialyzable. These experiments indicate that GCS-induced Ig production by human B cells does not require the presence of intact T cells in the cultures and therefore the steroids are not exerting their influence directly on T suppressor or T helper cells. Furthermore, they demonstrate a previously unrecognized cytokine that induces the differentiation of human B cells to Ig production in the presence of GCS. PMID:6605406

Applying PWM to control overcurrents at unbalanced faults of force-commutated VSCs used as static var compensators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Y.; Ekstroem, A.

1997-01-01

This study is devoted to investigating the possibility of controlling the overcurrent of a forced-commutated voltage source converter (VSC) by PWM when the ac system is undergoing large unbalanced disturbance. The converter is supposed to be used as a static var compensator at a high power level. A novel control strategy is proposed for controlling the reactive current and the dc side voltage independently. Digital simulation results are presented and compared with the results by using just the reactive current control with fundamental switching frequency.

Fast controller for a unity-power-factor PWM rectifier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eissa, M.O.; Leeb, S.B.; Verghese, G.C.

1996-01-01

This paper presents an analog implementation of a fast controller for a unity-power-factor (UPF) PWM rectifier. The best settling times of many popular controllers for this type of converter are on the order of a few line cycles, corresponding to bandwidths under 20 Hz. The fast controller demonstrated in this paper can exercise control action at a rate comparable to the switching frequency rather than the line frequency. In order to accomplish this while maintaining unity power factor during steady-state operation, the fast controller employs a ripple-feedback cancellation scheme.

A High Power Density Single-Phase PWM Rectifier with Active Ripple Energy Storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ning, Puqi; Wang, Ruxi; Wang, Fei

It is well known that there exist second-order harmonic current and corresponding ripple voltage on dc bus for single phase PWM rectifiers. The low frequency harmonic current is normally filtered using a bulk capacitor in the bus which results in low power density. This paper proposed an active ripple energy storage method that can effectively reduce the energy storage capacitance. The feed-forward control method and design considerations are provided. Simulation and 15 kW experimental results are provided for verification purposes.

Effects of macrocyclic trichothecene mycotoxins on the murine immune system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hughes, B.J.

1988-01-01

The macrocyclic trichothecenes are a unique group of toxins which have some antileukemic properties. In the first study, verrucarin A and roridin A were examined. Both mycotoxins were administered intraperitoneally at an equitoxic dose of 0.35 mg/kg to CD-1 mice. Lymphocyte proliferation was studied after animals were dosed with verrucarin A. After day 2, no differences in {sup 3}H-thymidine incorporation were observed using concanavalin A (Con A), phytohemagglutinin (PHA), pokeweed mitogen (PWM), or lipopolysaccharide (LPS). On day 4, DNA synthesis induced by Con A, PHA, and PWM increased significantly. On day 7, PHA stimulation increased above controls while Con A,more » PWM, and LPS responses were not significantly different. In contrast, roridin A decreased PHA stimulation only on day 7. In the second study the mycotoxins roritoxin B, myrotoxin B, roridin A, verrucarin A, 16-hydroxyverrucarin A, verrucarin J, baccharinoid B12, roridin D, roridin E, baccharinoid B4, and baccharinoid B5 were investigated. In the third study lymphocytes were cultured with each of the mycotoxins for 48 hr to assess their lethality.« less

Bi-directional power control system for voltage converter

DOEpatents

Garrigan, Neil Richard; King, Robert Dean; Schwartz, James Edward

1999-01-01

A control system for a voltage converter includes: a power comparator for comparing a power signal on input terminals of the converter with a commanded power signal and producing a power comparison signal; a power regulator for transforming the power comparison signal to a commanded current signal; a current comparator for comparing the commanded current signal with a measured current signal on output terminals of the converter and producing a current comparison signal; a current regulator for transforming the current comparison signal to a pulse width modulator (PWM) duty cycle command signal; and a PWM for using the PWM duty cycle command signal to control electrical switches of the converter. The control system may further include: a command multiplier for converting a voltage signal across the output terminals of the converter to a gain signal having a value between zero (0) and unity (1), and a power multiplier for multiplying the commanded power signal by the gain signal to provide a limited commanded power signal, wherein power comparator compares the limited commanded power signal with the power signal on the input terminals.

Bi-directional power control system for voltage converter

DOEpatents

Garrigan, N.R.; King, R.D.; Schwartz, J.E.

1999-05-11

A control system for a voltage converter includes: a power comparator for comparing a power signal on input terminals of the converter with a commanded power signal and producing a power comparison signal; a power regulator for transforming the power comparison signal to a commanded current signal; a current comparator for comparing the commanded current signal with a measured current signal on output terminals of the converter and producing a current comparison signal; a current regulator for transforming the current comparison signal to a pulse width modulator (PWM) duty cycle command signal; and a PWM for using the PWM duty cycle command signal to control electrical switches of the converter. The control system may further include: a command multiplier for converting a voltage signal across the output terminals of the converter to a gain signal having a value between zero (0) and unity (1), and a power multiplier for multiplying the commanded power signal by the gain signal to provide a limited commanded power signal, wherein power comparator compares the limited commanded power signal with the power signal on the input terminals. 10 figs.

Induction of suppressor cells from peripheral blood T cells by 15-hydroperoxyeicosatetraenoic acid (15-HPETE).

PubMed

Gualde, N; Rigaud, M; Goodwin, J S

1985-11-01

15-hydroperoxyeicosetetraenoic acid (15-HPETE), a lipoxygenase metabolite of arachidonic acid, inhibited polyclonal IgG and IgM production in pokeweed mitogen (PWM)-stimulated cultures of human peripheral blood mononuclear cells, whereas 15-hydroxyeicosetetraenoic acid (15-HETE) had little effect in this system. T cells preincubated for 18 hr with 15-HPETE caused substantial inhibition of IgG and IgM production of fresh, autologous B and T cells stimulated by PWM. The suppressive effect of the 15-HPETE-treated cells was lost if the cells were irradiated before the PWM culture, but not by treatment with mitomycin C. The suppressive effect was also lost if OKT8+ T cells were removed after, but not before, preincubation of the T cells with 15-HPETE. OKT8- T cells incubated with 15-HPETE for 18 hr showed a large increase in the percentage of cells staining with directly fluoresceinated Leu-2, another marker for suppressor cells. Thus, 15-HPETE induces functional and phenotypic suppressor cells from resting human peripheral blood T cells.

Finger vein recognition based on personalized weight maps.

PubMed

Yang, Gongping; Xiao, Rongyang; Yin, Yilong; Yang, Lu

2013-09-10

Finger vein recognition is a promising biometric recognition technology, which verifies identities via the vein patterns in the fingers. Binary pattern based methods were thoroughly studied in order to cope with the difficulties of extracting the blood vessel network. However, current binary pattern based finger vein matching methods treat every bit of feature codes derived from different image of various individuals as equally important and assign the same weight value to them. In this paper, we propose a finger vein recognition method based on personalized weight maps (PWMs). The different bits have different weight values according to their stabilities in a certain number of training samples from an individual. Firstly we present the concept of PWM, and then propose the finger vein recognition framework, which mainly consists of preprocessing, feature extraction, and matching. Finally, we design extensive experiments to evaluate the effectiveness of our proposal. Experimental results show that PWM achieves not only better performance, but also high robustness and reliability. In addition, PWM can be used as a general framework for binary pattern based recognition.

Finger Vein Recognition Based on Personalized Weight Maps

PubMed Central

Yang, Gongping; Xiao, Rongyang; Yin, Yilong; Yang, Lu

2013-01-01

Finger vein recognition is a promising biometric recognition technology, which verifies identities via the vein patterns in the fingers. Binary pattern based methods were thoroughly studied in order to cope with the difficulties of extracting the blood vessel network. However, current binary pattern based finger vein matching methods treat every bit of feature codes derived from different image of various individuals as equally important and assign the same weight value to them. In this paper, we propose a finger vein recognition method based on personalized weight maps (PWMs). The different bits have different weight values according to their stabilities in a certain number of training samples from an individual. Firstly we present the concept of PWM, and then propose the finger vein recognition framework, which mainly consists of preprocessing, feature extraction, and matching. Finally, we design extensive experiments to evaluate the effectiveness of our proposal. Experimental results show that PWM achieves not only better performance, but also high robustness and reliability. In addition, PWM can be used as a general framework for binary pattern based recognition. PMID:24025556

Principle and design of small-sized and high-definition x-ray machine

NASA Astrophysics Data System (ADS)

Zhao, Anqing

2010-10-01

The paper discusses the circuit design and working principles of VMOS PWM type 75KV10mA high frequency X-ray machine. The system mainly consists of silicon controlled rectifier, VMOS tube PWM type high-frequency and highvoltage inverter circuit, filament inverter circuit, high-voltage rectifier filter circuit and as X-ray tube. The working process can be carried out under the control of a single-chip microcomputer. Due to the small size and high resolution in imaging, the X-ray machine is mostly adopted for emergent medical diagnosis and specific circumstances where nondestructive tests are conducted.

Design of a ZVS PWM inverter for a brushless DC motor in an EMA application

NASA Technical Reports Server (NTRS)

Bell, J. Brett; Nelms, R. M.; Shepherd, Michael T.

1993-01-01

The Component Development Division of the Propulsion Laboratory at Marshall Space Flight Center (MSFC) is currently investigating the use of electromechanical actuators for use in space transportation applications such as Thrust Vector Control (TVC). These high power servomechanisms will require rugged, reliable, and compact power electronic modules capable of modulating several hundred amperes of current at up to 270 Vdc. This paper will discuss the design and implementation of a zero-voltage-switched PWM (Pulse Width Modulation) inverter which operates from a 270 Vdc source at currents up to 100 A.

Prediction of Trace Element based Energizing Sensor Control System using PWM

NASA Astrophysics Data System (ADS)

Zukri, Mohammad Nizar Bin Mohamed; Abu Bakar, Elmi Bin; Uchiyama, Naoki; Abdullah, Mohamad Nazir Bin

2018-05-01

A real-time system for field-work monitoring wastewater laden with heavy metal in industrial discharge through wireless communication network was developed. The monitoring system poses an interesting challenge in order to determine existing metal ion in the solution whereas the previous result only consider total dissolve ion. This paper aims to distinguish the metal ion based on reaction determination in solution. The control algorithm was implemented as generating voltage input for energize conductivity sensor since the voltage corresponding to oxidation and reaction based on standard reduction potential. Implementation of ATmega2560 microcontroller for control voltage fed on sensor equivalent to controlling the PWM duty cycle. PID controller was designed uses a microcontroller (Arduino) platform with manual tuning for identify reaction process and sufficient voltage input. From the experimental result, is found that the proposed PI controller has excellent tracking and measurement performance. Low-pass filter was applied in programming to make the system understand that signal has achieved stable. The development of hardware and software of the closed loop system has an enhancement of measurement performance and high feasibility for SME’s company in economic point of view. The desired objective is to achieve a system with the stable measurement and sufficient voltage supply. This system will provide an accurate and precise control efficiently without using costly component and complicated circuit.

Control of polyclonal immunoglobulin production from human lymphocytes by leukotrienes; leukotriene B4 induces an OKT8(+), radiosensitive suppressor cell from resting, human OKT8(-) T cells.

PubMed Central

Atluru, D; Goodwin, J S

1984-01-01

We report that leukotriene B4 (LTB4), a 5-lipoxygenase metabolite of arachidonic acid, is a potent suppressor of polyclonal Ig production in pokeweed mitogen (PWM)-stimulated cultures of human peripheral blood lymphocytes, while LTC4 and LTD4 have little activity in this system. Preincubation of T cells with LTB4 in nanomolar to picomolar concentrations rendered these cells suppressive of Ig production in subsequent PWM-stimulated cultures of fresh, autologous B + T cells. This LTB4-induced suppressor cell was radiosensitive, and its generation could be blocked by cyclohexamide but not by mitomycin C. The LTB4-induced suppressor cell was OKT8(+), while the precursor for the cell could be OKT8(-). The incubation of OKT8(-) T cells with LTB4 for 18 h resulted in the appearance of the OKT8(+) on 10-20% of the cells, and this could be blocked by cyclohexamide but not by mitomycin C. Thus, LTB4 in very low concentrations induces a radiosensitive OKT8(+) suppressor cell from OKT8(-) cells. In this regard, LTB4 is three to six orders of magnitude more potent than any endogenous hormonal inducer of suppressor cells previously described. Glucocorticosteroids, which block suppressor cell induction in many systems, may act by inhibiting endogenous production of LTB4. Images PMID:6090503

Effects of Inteferons on Human B-cell Differentiation in vitro

PubMed Central

Kim, Samyong; Stoetter, Hans; Heimpel, Herrman

1987-01-01

The effects of interferons (IFN) on in vitro differentiation of B-lymphocytes were studied. Peripheral lymphocytes from normal subjects were cultivated under polyclonal activator pokeweed mitogen (PWN) or Epstein-Barr virus (EBV) stimulation. The secreted Ig in the culture supernatants were measured for IgM by ELISA method. To determine the cellular level of IFN action T-cell enriched fraction (Te) or B-cell enriched fraction (Be) were preincubated with IFN prior to recombination culture. IFN had modulatory activities on Ig production; at low to moderately high doses (10–1000 U/ml of IFN-alpha or 12–120 U/ml of IFN-gamma) stimulating when IFN was added until 48 hr after the start of the culture, while after 72 hr from culture start IFN suppressed Ig production. Preincubation of Be-cells with moderately high doses of IFN (120 U/ml of IFN-gamma or 1000 U/ml of IFN-alpha) prior to PWM-stimulation suppressed Ig production. Likewise, in EBV-stimulated culture, high dose IFN suppressed Ig production. But low dose of IFN enhanced ig production in EBV-stimulated culture. Preincubation of Te-cells with IFN prior to PWM-stimulation with Be-cells enhanced the Ig production. The T-cell subset analysis at the end of these culture showed enhanced ratio of T-helper cell relative to T-suppressor cells, suggesting increased T-helper cell proliferation after incubation with IFN. Thus, it is concluded that IFNs have modulatory activities on B-cell differentiation. The mechanism seems to be direct effects on B-cells (in PWM and EBV system) as well as through T-helper cell mediation (PWM system). The IFN-gamma showed more potent (2-to 6-fold) stimulatory activities than IFN-alpha. PMID:2484953

Performance analysis of cascaded h-bridge multilevel inverter using mixed switching frequency with various dc-link voltages

NASA Astrophysics Data System (ADS)

Citarsa, I. B. F.; Satiawan, I. N. W.; Wiryajati, I. K.; Supriono

2016-01-01

Multilevel inverters have been widely used in many applications since the technology is advantageous to increase the converter capability as well as to improve the output voltage quality. According to the applied switching frequency, multilevel modulations can be subdivided into three classes, i.e: fundamental switching frequency, high switching frequency and mixed switching frequency. This paper investigates the performance of cascaded H-bridge (CHB) multilevel inverter that is modulated using mixed switching frequency (MSF) PWM with various dc-link voltage ratios. The simulation results show the nearly sinusoidal load output voltages are successfully achieved. It is revealed that there is improvement in output voltages quality in terms of THD and low-order harmonics content. The CHB inverter that is modulated using MSF PWM with equal dc-link voltage ratio (½ Vdc: ½ Vdc) produces output voltage with the lowest low-order harmonics (less than 1% of fundamental) while the CHB inverter that is modulated using MSF PWM with un-equal dc-link voltage ratio (2/3 Vdc: 1/3 Vdc) produces a 7-level output voltage with the lowest THD (16.31%) compared to the other PWM methods. Improvement of the output voltage quality here is also in line with improvement of the number of available levels provided in the output voltage. Here only 2 cells H-bridge inverter (contain 8 switches) are needed to produce a 7- level output voltage, while in the conventional CHB inverter at least 3 cells of H-bridge inverter (contain 12 switches) are needed to produce a 7-level output voltage. Hence it is valuable in term of saving number of component.

The Design and Development of the SMEX-Lite Power System

NASA Technical Reports Server (NTRS)

Rakow, Glenn P.; Schnurr, Richard G., Jr.; Solly, Michael A.

1998-01-01

This paper describes the design and development of a 250W orbit average electrical power system electronic Power Node and software for use in Low Earth Orbit missions. The mass of the Power Node is 3.6 Kg (8 lb.). The dimensions of the Power Node are 30cm x 26cm x 7.9cm (11 in. x 10.25 in x 3.1 in.) The design was realized using software, Field Programmable Gate Array (FPGA) digital logic and surface mount technology. The design is generic enough to reduce the non-recurring engineering for different mission configurations. The Power Node charges one to five, low cost, 22-cell 4 AH D-cell battery packs independently. The battery charging algorithms are executed in the power software to reduce the mass and size of the power electronic. The Power Node implements a peak-power tracking algorithm using an innovative hardware/software approach. The power software task is hosted on the spacecraft processor. The power software task generates a MIL-STD-1553 command packet to update the Power Node control settings. The settings for the battery voltage and current limits, as well as minimum solar array voltage used to implement peak power tracking are contained in this packet. Several advanced topologies are used in the Power Node. These include synchronous rectification in the bus regulators, average current control in the battery chargers and quasi-resonant converters for the Field Effect Transistor (FET) transistor drive electronics. Lastly, the main bus regulator uses a feed-forward topology with the PWM implemented in an FPGA.

Parallel PWMs Based Fully Digital Transmitter with Wide Carrier Frequency Range

PubMed Central

Zhou, Bo; Zhang, Kun; Zhou, Wenbiao; Zhang, Yanjun; Liu, Dake

2013-01-01

The carrier-frequency (CF) and intermediate-frequency (IF) pulse-width modulators (PWMs) based on delay lines are proposed, where baseband signals are conveyed by both positions and pulse widths or densities of the carrier clock. By combining IF-PWM and precorrected CF-PWM, a fully digital transmitter with unit-delay autocalibration is implemented in 180 nm CMOS for high reconfiguration. The proposed architecture achieves wide CF range of 2 M–1 GHz, high power efficiency of 70%, and low error vector magnitude (EVM) of 3%, with spectrum purity of 20 dB optimized in comparison to the existing designs. PMID:24223503

Perceptions of organ donors and willingness to donate organs upon death: a test of the prototype/willingness model.

PubMed

Hyde, Melissa K; White, Katherine M

2014-01-01

Understanding people's organ donation decisions may narrow the gap between organ supply and demand. In two studies, participants who had not recorded their posthumous organ donation decision (Study 1, N = 210; Study 2, N = 307) completed items assessing prototype/willingness model (PWM; attitude, subjective norm, donor prototype favorability and similarity, willingness) constructs. Attitude, subjective norm, and prototype similarity predicted willingness to donate. Prototype favorability and a Prototype Favorability × Similarity interaction predicted willingness (Study 2). These findings provide support for the PWM in altruistic health contexts, highlighting the importance of people's perceptions about organ donors in their donation decisions.

Perceptions of Organ Donors and Willingness to Donate Organs Upon Death: A Test of the Prototype/Willingness Model.

PubMed

Hyde, Melissa K; White, Katherine M

2014-06-09

Understanding people's organ donation decisions may narrow the gap between organ supply and demand. In two studies, participants who had not recorded their posthumous organ donation decision (Study 1 N = 210; Study 2 N = 307) completed items assessing Prototype/Willingness Model (PWM) (attitude, subjective norm, donor prototype favorability and similarity, willingness) constructs. Attitude, subjective norm, and prototype similarity predicted willingness to donate. Prototype favorability and a prototype favorability x similarity interaction predicted willingness (Study 2). These findings provide support for the PWM in altruistic health contexts, highlighting the importance of people's perceptions about organ donors in their donation decisions.

PWM Inverter with Voltage Boosters with Regenerating Capability Augmented by Electric Double-Layer Capacitor

NASA Astrophysics Data System (ADS)

Yamamoto, Kichiro; Imakiire, Akihiro; Iimori, Kenichi

An interior permanent magnet (IPM) motor drive system which has regenerating capability augmented by electric double-layer capacitors (EDLCs) is proposed. In the proposed system, EDLCs are arranged in series with batteries so that a lesser number of the EDLCs and batteries will be required. The proposed system has two bi-directional voltage boosters: one is for both the batteries and EDLCs to control the dc-link voltage of a PWM inverter and the other is for only the EDLCs and is used to control the energy flow from and to the EDLCs. In this paper, a strategy to control the energy flow to and from the EDLCs is explained and its effectiveness is confirmed by simulation and experimental results. Furthermore, the efficiencies of the voltage booster, inverter, PM motor, and whole system are measured for the system with the basic configuration, i.e., which consists of only one bi-directional voltage booster and PWM inverter. Then, the steady-state characteristics are determined. Finally, the efficiency of the voltage boosters in the proposed system is determined, and the advantage of the proposed PM motor drive system is discussed.

Permanent Magnet Synchronous Motor Driven by PWM Inverter with Voltage Booster with Regenerating Capability Augmented by Double-Layer Capacitor

NASA Astrophysics Data System (ADS)

Yamamoto, Kichiro; Shinohara, Katsuji; Furukawa, Shinya

An interior permanent magnet (IPM) motor drive system which has regenerating capability augmented by double-layer capacitors is proposed. The motor is driven by a PWM inverter with voltage booster. The voltage booster is used to control the dc link voltage in high speed region to improve the system efficiency. Furthermore, the double-layer capacitor as a storage element is combined with the PWM inverter with voltage booster to gain the efficiency for the regenerating operation. In this system, normally, the regenerative power does not return to a battery directly but is stored in the double-layer capacitors for the next motoring action to suppress the excessive regenerative current to battery, and the regenerative power returns to the battery when the regenerative energy is larger than a certain value. The charging current to the battery is controlled to a constant value to extend the life-time of the battery. The transient and steady state characteristics of the system for 1.5kW IPM motor are investigated by both simulation and experiment. Finally, the effectiveness of the system is demonstrated by the simulated and experimental results.

Low-Cost Servomotor Driver for PFM Control

PubMed Central

Aragon-Jurado, David

2017-01-01

Servomotors have already been around for some decades and they are extremely popular among roboticists due to their simple control technique, reliability and low-cost. They are usually controlled by using Pulse Width Modulation (PWM) and this paper aims to keep the idea of simplicity and low-cost, while introducing a new control technique: Pulse Frequency Modulation (PFM). The objective of this paper is to focus on our development of a low-cost servomotor controller which will allow the research community to use them with PFM. A low-cost commercial servomotor is used as the base system for the development: a small PCB that fits inside the case and allocates all the electronic components to control the motor has been designed to replace the original. The potentiometer is retained as the feedback sensor and a microcontroller is responsible for controlling the position of the motor. The paper compares the performance of a PWM and a PFM controlled servomotor. The comparison shows that the servomotor with our controller achieves a faster mechanism for switching targets and a lower latency. This controller can be used with neuromorphic systems to remove the conversion from events to PWM. PMID:29301221

Low-Cost Servomotor Driver for PFM Control.

PubMed

Aragon-Jurado, David; Morgado-Estevez, Arturo; Perez-Peña, Fernando

2017-12-31

Servomotors have already been around for some decades and they are extremely popular among roboticists due to their simple control technique, reliability and low-cost. They are usually controlled by using Pulse Width Modulation (PWM) and this paper aims to keep the idea of simplicity and low-cost, while introducing a new control technique: Pulse Frequency Modulation (PFM). The objective of this paper is to focus on our development of a low-cost servomotor controller which will allow the research community to use them with PFM. A low-cost commercial servomotor is used as the base system for the development: a small PCB that fits inside the case and allocates all the electronic components to control the motor has been designed to replace the original. The potentiometer is retained as the feedback sensor and a microcontroller is responsible for controlling the position of the motor. The paper compares the performance of a PWM and a PFM controlled servomotor. The comparison shows that the servomotor with our controller achieves a faster mechanism for switching targets and a lower latency. This controller can be used with neuromorphic systems to remove the conversion from events to PWM.

Metabolic alterations and neurodevelopmental outcome of infants with transposition of the great arteries.

PubMed

Park, I Sook; Yoon, S Young; Min, J Yeon; Kim, Y Hwue; Ko, J Kok; Kim, K Soo; Seo, D Man; Lee, J Hee

2006-01-01

Abnormal neurodevelopment has been reported for infants who were born with transposition of the great arteries (TGA) and underwent arterial switch operation (ASO). This study evaluates the cerebral metabolism of TGA infants at birth and before ASO and neurodevelopment 1 year after ASO. Proton magnetic resonance spectroscopy (1H-MRS) was performed on 16 full-term TGA brains before ASO within 3-6 days after birth. The brain metabolite ratios of [NAA/Cr], [Cho/Cr], and [mI/Cr] evaluated measured. Ten infants were evaluated at 1 year using the Bayley Scales of Infants Development II (BSED II). Cerebral metabolism of infants with TGA was altered in parietal white matter (PWM) and occipital gray matter (OGM) at birth before ASO. One year after ASO, [Cho/Cr] in PWM remained altered, but all metabolic ratios in OGM were normal. The results of BSID II at 1 year showed delayed mental and psychomotor development. This delayed neurodevelopmental outcome may reflect consequences of the altered cerebral metabolism in PWM measured by 1H-MRS. It is speculated that the abnormal hemodynamics due to TGA in utero may be responsible for the impaired cerebral metabolism and the subsequent neurodevelopmental deficit.

A new topology and control method for electromagnetic transmitter power supplies

NASA Astrophysics Data System (ADS)

Zhang, Yiming; Zhang, Jialin; Yuan, Dakang

2017-04-01

As essential equipment for electromagnetic exploration, electromagnetic transmitter reverse the steady power supply with desired frequency and transmit the power through grounding electrodes. To obtain effective geophysical data during deep exploration, the transmitter needs to be high-voltage, high-current, with high-accuracy output, and yet compact and light. The researches on the power supply technologies for high-voltage high-power electromagnetic transmitter is of significant importance to the deep geophysical explorations. Therefore, the performance of electromagnetic transmitter is mainly subject to the following two aspects: the performance of emission current and voltage, and the power density. These requirements bring technical difficulties to the development of power supplies. Conventionally, high-frequency switching power supplies are applied in the design of a high-power transmitter power supply. However, the structure of the topology is complicate, which may reduce the controllability of the output voltage and the reliability of the system. Without power factor control, the power factor of the structure is relatively low. Moreover high switching frequency causes high loss. With the development of the PWM (pulse width modulation) technique, its merits of simple structure, low loss, convenient control and unit power factor have made it popular in electrical energy feedback, active filter, and power factor compensation. Studies have shown that using PWM converters and space vector modulation have become the trend in designing transmitter power supply. However, the earth load exhibits different impedances at different frequencies. Thus ensuing high-accuracy and a stable output from a transmitter power supply in harsh environment has become a key topic in the design of geophysical exploration instruments. Based on SVPWM technology, an electromagnetic transmitter power supply has been designed and its control strategy has been studied. The transmitting system is composed of power supply, SVPWM converter, and power inverter units. The functions of the units are as follows: (1) power supply: a generator providing power with three phase; (2) SVPWM converter: convert AC to DC output; (3) power inverter unit: the inverter is used to convert DC to AC output whose frequency, amplitude and waveform are variable. In the SVPWM technique, the active current and the reactive current are controlled separately, and each variable is analyzed individually, thus the power factor of the system is improved. Through controlling the PWM converter at the generation side, we can get any power factor. Usually the power factor of the generation side is set to 1. Finally, simulation and experimental results validate both the correctness of the established model and the effectiveness of the control method. We can acquire unity power factor for the input and steady current for the output. They also demonstrated that the electromagnetic transmitter power supply designed in this study can meet the practical needs of field geological exploration. We can improve the utilization of the transmitter system.

Caracterisation des mecanismes d'usure en cavitation de revetements HVOF a base de CaviTec

NASA Astrophysics Data System (ADS)

Lavigne, Sebastien

The increasing demand for high performance power conversion systems continuously pushes for improvement in efficiency and power density. This dissertation focuses on a topological effort to efficiently utilize the active and passive devices. In particular, a hybrid approach is adopted, where both capacitors and inductors are used in the voltage conversion and power transfer process. Conventional capacitor-based converters, called switched-capacitor (SC) converters, suffer from poor efficiency due to the inevitable charge redistribution process. With a strategic placement of one or more inductors, the charge redistribution loss can be eliminated by inductively charging/discharging the capacitors, a process called soft-charging operation. As a result, the capacitor size can be greatly reduced without reducing the efficiency. A general analytical framework is presented, which determines whether an arbitrary SC topology is able to achieve full soft-charging operation with a single inductor. For topologies that cannot, a split-phase control technique is introduced, which amends existing two-phase controls to completely eliminate the charge redistribution loss. In addition, alternative placements of inductors are explored to extend the family of hybrid converters. The hybrid converters can have two modes of operation, the fixed-ratio mode and pulse width modulated (PWM) mode. The fixed-conversion-ratio hybrid converters operate in a similar manner to that of a conventional SC converter, with the addition of a soft-charging inductor. The switching frequency of such converters can be adjusted to operate in either zero current switching (ZCS) mode or continuous conduction mode (CCM), which allows for the trade-off of switching loss and conduction loss. It is shown that the capacitor and inductor values can be selected to achieve a minimal passive component volume, which can be significantly smaller than that of a conventional SC converter or a magnetic-based converter. On the other hand, PWM-based hybrid converters generate a PWM rectangular wave as the terminal voltage to the inductor, similar to the operation of a buck converter. In contrast to conventional SC converters, such hybrid converters can achieve lossless and continuous regulation of the output voltage. Compared to buck converters, the required inductor is greatly reduced, as well as the switch stress. A 80-170 V input, 12-24 V output prototype PWM Dickson converter is implemented using GaN switches. The measured peak efficiency is 97%, and high efficiency can be maintained over the entire input and output operating range. In addition, the similarity between multilevel converters (for example, flying capacitor multilevel (FCML) converters) and the PWM-based hybrid SC converters is discussed. Both types of converters can be seen as a hybrid converter which uses both capacitors and inductors for energy transfer. A general framework to compare these converters, along with conventional buck converters, is proposed. In this framework, the power losses (including conduction loss and switching loss) are kept constant, while the total passive component volume is used as the figure of merit. Based on the principle of maximizing energy utilization of passive components, a 7-level FCML converter and an active energy buffer are designed and implemented for single phase dc-ac applications. In addition, the stand-alone system includes a start-up circuitry, EMC filter and auxiliary power supply. The enclosed box achieves a combined power density of 216 W/in3 and an efficiency of 97.4%, and compares favorably against the state-of-the-art designs under the same specification. To further improve the efficiency and power density, soft-switching techniques are investigated and applied on the hybrid converters. A zero voltage switching (ZVS) technique is introduced for both the fixed-ratio mode and the PWM mode operated hybrid converters. The previous hardware prototypes are modified for ZVS operation, and prove the feasibility of simultaneous soft-charging and soft-switching operation. Last but not the least, some of the practical issues associated with the hybrid converter are discussed, such as practical capacitor selection, capacitor voltage balancing and other circuit implementation challenges. Future work based on these topics is given. In summary, these hybrid converters are suited for applications where extreme efficiency and power density are critical. Through efficient utilization of active and passive devices, the hybrid topologies can offer a greater optimization opportunity and ability to take advantage of technology improvement than is possible with conventional designs.

Compensation for Harmonic Currents and Reactive Power in Wind Power Generation System using PWM Inverter

NASA Astrophysics Data System (ADS)

Shinohara, Katsuji; Shinhatsubo, Kurato; Iimori, Kenichi; Yamamoto, Kichiro; Saruban, Takamichi; Yamaemori, Takahiro

In recent year, consciousness of environmental problems is enhancing, and the price of the electric power purchased by an electric power company is established expensive for the power plant utilizing the natural energy. So, the introduction of the wind power generation is promoted in Japan. Generally, squirrel-cage induction machines are widely used as a generator in wind power generation system because of its small size, lightweight and low-cost. However, the induction machines do not have a source of excitation. Thus, it causes the inrush currents and the instantaneous voltage drop when the generator is directly connected to a power grid. To reduce the inrush currents, an AC power regulator is used. Wind power generations are frequently connected to and disconnected from the power grid. However, when the inrush currents are reduced, harmonic currents are caused by phase control of the AC power regulator. And the phase control of AC power regulator cannot control the power factor. Therefore, we propose the use of the AC power regulator to compensate for the harmonic currents and reactive power in the wind power generation system, and demonstrate the validity of its system by simulated and experimental results.

Digital current regulator for proportional electro-hydraulic valves with unknown disturbance rejection.

PubMed

Canuto, Enrico; Acuña-Bravo, Wilber; Agostani, Marco; Bonadei, Marco

2014-07-01

Solenoid current regulation is well-known and standard in any proportional electro-hydraulic valve. The goal is to provide a wide-band transfer function from the reference to the measured current, thus making the solenoid a fast and ideal force actuator within the limits of the power supplier. The power supplier is usually a Pulse Width Modulation (PWM) amplifier fixing the voltage bound and the Nyquist frequency of the regulator. Typical analog regulators include three main terms: a feedforward channel, a proportional feedback channel and the electromotive force compensation. The latter compensation may be accomplished by integrative feedback. Here the problem is faced through a model-based design (Embedded Model Control), on the basis of a wide-band embedded model of the solenoid which includes the effect of eddy currents. To this end model parameters must be identified. The embedded model includes a stochastic disturbance dynamics capable of estimating and correcting the electromotive contribution together with parametric uncertainty, variability and state dependence. The embedded model which is fed by the measured current and the supplied voltage becomes a state predictor of the controllable and disturbance dynamics. The control law combines reference generator, state feedback and disturbance rejection to dispatch the PWM amplifier with the appropriate duty cycle. Modeling, identification and control design are outlined together with experimental result. Comparison with an existing analog regulator is also provided. © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Inverter Output Filter Effect on PWM Motor Drives of a Flywheel Energy Storage System

NASA Technical Reports Server (NTRS)

Santiago, Walter

2004-01-01

NASA Glenn Research Center (GRC) has been involved in the research and development of high speed flywheel systems for small satellite energy storage and attitude control applications. One research and development area has been the minimization of the switching noise produced by the pulsed width modulated (PWM) inverter that drives the flywheel permanent magnet motor/generator (PM M/G). This noise can interfere with the flywheel M/G hardware and the system avionics hampering the full speed performance of the flywheel system. One way to attenuate the inverter switching noise is by placing an AC filter at the three phase output terminals of the inverter with the filter neutral point connected to the DC link (DC bus) midpoint capacitors. The main benefit of using an AC filter in this fashion is the significant reduction of the inverter s high dv/dt switching and its harmonics components. Additionally, common mode (CM) and differential mode (DM) voltages caused by the inverter s high dv/dt switching are also reduced. Several topologies of AC filters have been implemented and compared. One AC filter topology consists of a two-stage R-L-C low pass filter. The other topology consists of the same two-stage R-L-C low pass filter with a series connected trap filter (an inductor and capacitor connected in parallel). This paper presents the analysis, design and experimental results of these AC filter topologies and the comparison between the no filter case and conventional AC filter.

Methods, systems and apparatus for controlling third harmonic voltage when operating a multi-space machine in an overmodulation region

DOEpatents

Perisic, Milun; Kinoshita, Michael H; Ranson, Ray M; Gallegos-Lopez, Gabriel

2014-06-03

Methods, system and apparatus are provided for controlling third harmonic voltages when operating a multi-phase machine in an overmodulation region. The multi-phase machine can be, for example, a five-phase machine in a vector controlled motor drive system that includes a five-phase PWM controlled inverter module that drives the five-phase machine. Techniques for overmodulating a reference voltage vector are provided. For example, when the reference voltage vector is determined to be within the overmodulation region, an angle of the reference voltage vector can be modified to generate a reference voltage overmodulation control angle, and a magnitude of the reference voltage vector can be modified, based on the reference voltage overmodulation control angle, to generate a modified magnitude of the reference voltage vector. By modifying the reference voltage vector, voltage command signals that control a five-phase inverter module can be optimized to increase output voltages generated by the five-phase inverter module.

Decentralized Interleaving of Paralleled Dc-Dc Buck Converters: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Brian B; Rodriguez, Miguel; Sinha, Mohit

We present a decentralized control strategy that yields switch interleaving among parallel connected dc-dc buck converters without communication. The proposed method is based on the digital implementation of the dynamics of a nonlinear oscillator circuit as the controller. Each controller is fully decentralized, i.e., it only requires the locally measured output current to synthesize the pulse width modulation (PWM) carrier waveform. By virtue of the intrinsic electrical coupling between converters, the nonlinear oscillator-based controllers converge to an interleaved state with uniform phase-spacing across PWM carriers. To the knowledge of the authors, this work represents the first fully decentralized strategy formore » switch interleaving of paralleled dc-dc buck converters.« less

Methods, systems and apparatus for adjusting duty cycle of pulse width modulated (PWM) waveforms

DOEpatents

Gallegos-Lopez, Gabriel; Kinoshita, Michael H; Ransom, Ray M; Perisic, Milun

2013-05-21

Embodiments of the present invention relate to methods, systems and apparatus for controlling operation of a multi-phase machine in a vector controlled motor drive system when the multi-phase machine operates in an overmodulation region. The disclosed embodiments provide a mechanism for adjusting a duty cycle of PWM waveforms so that the correct phase voltage command signals are applied at the angle transitions. This can reduce variations/errors in the phase voltage command signals applied to the multi-phase machine so that phase current may be properly regulated thus reducing current/torque oscillation, which can in turn improve machine efficiency and performance, as well as utilization of the DC voltage source.

21 CFR 870.1750 - External programmable pacemaker pulse generator.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false External programmable pacemaker pulse generator. 870.1750 Section 870.1750 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... External programmable pacemaker pulse generator. (a) Identification. An external programmable pacemaker...

21 CFR 870.1750 - External programmable pacemaker pulse generator.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false External programmable pacemaker pulse generator. 870.1750 Section 870.1750 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... External programmable pacemaker pulse generator. (a) Identification. An external programmable pacemaker...

21 CFR 870.1750 - External programmable pacemaker pulse generator.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false External programmable pacemaker pulse generator. 870.1750 Section 870.1750 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... External programmable pacemaker pulse generator. (a) Identification. An external programmable pacemaker...

21 CFR 870.1750 - External programmable pacemaker pulse generator.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false External programmable pacemaker pulse generator. 870.1750 Section 870.1750 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... External programmable pacemaker pulse generator. (a) Identification. An external programmable pacemaker...

21 CFR 870.1750 - External programmable pacemaker pulse generator.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false External programmable pacemaker pulse generator. 870.1750 Section 870.1750 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... External programmable pacemaker pulse generator. (a) Identification. An external programmable pacemaker...

Constant-current control method of multi-function electromagnetic transmitter.

PubMed

Xue, Kaichang; Zhou, Fengdao; Wang, Shuang; Lin, Jun

2015-02-01

Based on the requirements of controlled source audio-frequency magnetotelluric, DC resistivity, and induced polarization, a constant-current control method is proposed. Using the required current waveforms in prospecting as a standard, the causes of current waveform distortion and current waveform distortion's effects on prospecting are analyzed. A cascaded topology is adopted to achieve 40 kW constant-current transmitter. The responsive speed and precision are analyzed. According to the power circuit of the transmitting system, the circuit structure of the pulse width modulation (PWM) constant-current controller is designed. After establishing the power circuit model of the transmitting system and the PWM constant-current controller model, analyzing the influence of ripple current, and designing an open-loop transfer function according to the amplitude-frequency characteristic curves, the parameters of the PWM constant-current controller are determined. The open-loop transfer function indicates that the loop gain is no less than 28 dB below 160 Hz, which assures the responsive speed of the transmitting system; the phase margin is 45°, which assures the stabilization of the transmitting system. Experimental results verify that the proposed constant-current control method can keep the control error below 4% and can effectively suppress load change caused by the capacitance of earth load.

Constant-current control method of multi-function electromagnetic transmitter

NASA Astrophysics Data System (ADS)

Xue, Kaichang; Zhou, Fengdao; Wang, Shuang; Lin, Jun

2015-02-01

Based on the requirements of controlled source audio-frequency magnetotelluric, DC resistivity, and induced polarization, a constant-current control method is proposed. Using the required current waveforms in prospecting as a standard, the causes of current waveform distortion and current waveform distortion's effects on prospecting are analyzed. A cascaded topology is adopted to achieve 40 kW constant-current transmitter. The responsive speed and precision are analyzed. According to the power circuit of the transmitting system, the circuit structure of the pulse width modulation (PWM) constant-current controller is designed. After establishing the power circuit model of the transmitting system and the PWM constant-current controller model, analyzing the influence of ripple current, and designing an open-loop transfer function according to the amplitude-frequency characteristic curves, the parameters of the PWM constant-current controller are determined. The open-loop transfer function indicates that the loop gain is no less than 28 dB below 160 Hz, which assures the responsive speed of the transmitting system; the phase margin is 45°, which assures the stabilization of the transmitting system. Experimental results verify that the proposed constant-current control method can keep the control error below 4% and can effectively suppress load change caused by the capacitance of earth load.

The Applicability of Confidence Intervals of Quantiles for the Generalized Logistic Distribution

NASA Astrophysics Data System (ADS)

Shin, H.; Heo, J.; Kim, T.; Jung, Y.

2007-12-01

The generalized logistic (GL) distribution has been widely used for frequency analysis. However, there is a little study related to the confidence intervals that indicate the prediction accuracy of distribution for the GL distribution. In this paper, the estimation of the confidence intervals of quantiles for the GL distribution is presented based on the method of moments (MOM), maximum likelihood (ML), and probability weighted moments (PWM) and the asymptotic variances of each quantile estimator are derived as functions of the sample sizes, return periods, and parameters. Monte Carlo simulation experiments are also performed to verify the applicability of the derived confidence intervals of quantile. As the results, the relative bias (RBIAS) and relative root mean square error (RRMSE) of the confidence intervals generally increase as return period increases and reverse as sample size increases. And PWM for estimating the confidence intervals performs better than the other methods in terms of RRMSE when the data is almost symmetric while ML shows the smallest RBIAS and RRMSE when the data is more skewed and sample size is moderately large. The GL model was applied to fit the distribution of annual maximum rainfall data. The results show that there are little differences in the estimated quantiles between ML and PWM while distinct differences in MOM.

Cerebral metabolic abnormalities in congestive heart failure detected by proton magnetic resonance spectroscopy.

PubMed

Lee, C W; Lee, J H; Kim, J J; Park, S W; Hong, M K; Kim, S T; Lim, T H; Park, S J

1999-04-01

Using proton magnetic resonance spectroscopy, we investigated cerebral metabolism and its determinants in congestive heart failure (CHF), and the effects of cardiac transplantation on these measurements. Few data are available about cerebral metabolism in CHF. Fifty patients with CHF (ejection fraction < or = 35%) and 20 healthy volunteers were included for this study. Of the patients, 10 patients underwent heart transplantation. All subjects performed symptom-limited bicycle exercise test. Proton magnetic resonance spectroscopy (1H MRS) was obtained from localized regions (8 to 10 ml) of occipital gray matter (OGM) and parietal white matter (PWM). Absolute levels of the metabolites (N-acetylaspartate, creatine, choline, myo-inositol) were calculated. In PWM only creatine level was significantly lower in CHF than in control subjects, but in OGM all four metabolite levels were decreased in CHF. The creatine level was independently correlated with half-recovery time and duration of heart failure symptoms in PWM (r = -0.56, p < 0.05), and with peak oxygen consumption and serum sodium concentration in OGM (r = 0.58, p < 0.05). Cerebral metabolic abnormalities were improved after successful cardiac transplantation. This study shows that cerebral metabolism is abnormally deranged in advanced CHF and it may serve as a potential marker of the disease severity.

Understanding the psychological precursors of young drivers' willingness to speed and text while driving.

PubMed

Preece, Carissa; Watson, Angela; Kaye, Sherrie-Anne; Fleiter, Judy

2018-08-01

This study applied the Prototype Willingness Model (PWM) to investigate the factors that may predict young drivers' (non-intentional) willingness to text while driving, text while stopped, and engage in high and low levels of speeding. In addition, the study sought to assess whether general optimism bias would predict young drivers' willingness to text and speed over and above the PWM. Licenced drivers (N = 183) aged 17-25 years (M = 19.84, SD = 2.30) in Queensland, Australia completed an online survey. Hierarchical multiple regressions revealed that the PWM was effective in explaining the variance in willingness to perform all four illegal driving behaviours. Particularly, young drivers who possessed favourable attitudes and a positive prototype perception towards these behaviours were more willing to engage in texting and speeding. In contrast to the study's predictions, optimistically biased beliefs decreased young drivers' willingness to text while stopped and engage in high and low levels of speeding. The findings of the study may help inform policy and educational campaigns to better target risky driving behaviours by considering the influence of attitudes, prototypes and the non-intentional pathway that may lead to engagement in texting while driving and stopped and engagement in high and low levels of speeding. Copyright © 2018 Elsevier Ltd. All rights reserved.

Leukoproliferative response of splenocytes from English sole (Pleuronectes vetulus) exposed to chemical contaminants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arkoosh, M.R.; Clemons, E.; Huffman, P.

The leukoproliferative (LP) response of splenic leukocytes from the marine benthic fish English sole (Pleuronectes vetulus) stimulated with the mitogens lipopolysaccharide (LPS), convanavalin A (Con A), and pokeweed mitogen (PWM) was examined as a biomarker of immunotoxic effects. English sole were exposed to contaminants, either by injection of an organic-solvent extract of a sediment containing polycyclic aromatic compounds (PACs) or placed for up to 5 weeks on a reference sediment containing 0.15 to 1.5% (v/v) of the PAC-contaminated sediment. English sole either injected with the contaminated extract or held on PAC-contaminated sediment had an augmented response to Con A. Themore » LP response to LPS showed no relationship to PAC exposure in laboratory-exposed fish, while PWM showed no consistent relationship to exposure to PACs. In a field study, English sole captured from an urban area in Puget Sound, Washington, USA, contaminated with PACs and other chemical contaminants had a significantly augmented LP response to Con A and PWM in comparison to the LP response in fish from a nonurban reference site. Fish from another nonurban site also had an augmented LP response to Con A, indicating that the elevation of the Con A LP response can also result from factors other than chemical contaminant exposure. In addition, English sole from this site also had an augmented LP response to LPS, whereas fish from urban sites did not exhibit an augmented LP response to LPS. Overall, the results demonstrated that although the LP response in splenic leukocytes of English sole to Con A was linked to contaminant exposure, the LP response to Con A did not exhibit high specificity as an indicator of chemical contaminant exposure. However, the concerted use of Con A, LPS, and PWM allowed for identification of apparent chemical contaminant-induced alterations of the LP response in English sole from an urban area of Puget Sound.« less

Structural Brain Damage and Upper Limb Kinematics in Children with Unilateral Cerebral Palsy.

PubMed

Mailleux, Lisa; Simon-Martinez, Cristina; Klingels, Katrijn; Jaspers, Ellen; Desloovere, Kaat; Demaerel, Philippe; Fiori, Simona; Guzzetta, Andrea; Ortibus, Els; Feys, Hilde

2017-01-01

Background: In children with unilateral cerebral palsy (uCP) virtually nothing is known on the relation between structural brain damage and upper limb (UL) kinematics quantified with three-dimensional movement analysis (3DMA). This explorative study aimed to (1) investigate differences in UL kinematics between children with different lesion timings, i.e., periventricular white matter (PWM) vs. cortical and deep gray matter (CDGM) lesions and (2) to explore the relation between UL kinematics and lesion location and extent within each lesion timing group. Methods: Forty-eight children (age 10.4 ± 2.7 year; 29 boys; 21 right-sided; 33 PWM; 15 CDGM) underwent an UL 3DMA during a reach-to-grasp task. Spatiotemporal parameters [movement duration, (timing of) maximum velocity, trajectory straightness], the Arm Profile Score (APS) and Arm Variable Scores (AVS) were extracted. The APS and AVS refer to the total amount of movement pathology and movement deviations of the wrist, elbow, shoulder, scapula and trunk respectively. Brain lesion location and extent were scored based on FLAIR-images using a semi-quantitative MRI-scale. Results: Children with CDGM lesions showed more aberrant spatiotemporal parameters ( p < 0.03) and more movement pathology (APS, p = 0.003) compared to the PWM group, mostly characterized by increased wrist flexion ( p = 0.01). In the CDGM group, moderate to high correlations were found between lesion location and extent and duration, timing of maximum velocity and trajectory straightness ( r = 0.53-0.90). Lesion location and extent were further moderately correlated with distal UL movement pathology (wrist flexion/extension, elbow pronation/supination, elbow flexion/extension; r = 0.50-0.65) and with the APS ( r = 0.51-0.63). In the PWM group, only a few and low correlations were observed, mostly between damage to the PLIC and higher AVS of elbow flexion/extension, shoulder elevation and trunk rotation ( r = 0.35-0.42). Regression analysis revealed damage to the temporal lobe with lesion timing as interactor (27%, p = 0.002) and the posterior limb of the internal capsule (PLIC) (7%, p = 0.04) as the strongest predictors, explaining 34% of the variance in APS. Conclusion: UL kinematic deviations are more influenced by lesion location and extent in children with later (CDGM) versus earlier lesions (PWM), except for proximal movement pathology. Damage to the PLIC is a significant predictor for UL movement pathology irrespective of lesion timing.

Transcription Factor Information System (TFIS): A Tool for Detection of Transcription Factor Binding Sites.

PubMed

Narad, Priyanka; Kumar, Abhishek; Chakraborty, Amlan; Patni, Pranav; Sengupta, Abhishek; Wadhwa, Gulshan; Upadhyaya, K C

2017-09-01

Transcription factors are trans-acting proteins that interact with specific nucleotide sequences known as transcription factor binding site (TFBS), and these interactions are implicated in regulation of the gene expression. Regulation of transcriptional activation of a gene often involves multiple interactions of transcription factors with various sequence elements. Identification of these sequence elements is the first step in understanding the underlying molecular mechanism(s) that regulate the gene expression. For in silico identification of these sequence elements, we have developed an online computational tool named transcription factor information system (TFIS) for detecting TFBS for the first time using a collection of JAVA programs and is mainly based on TFBS detection using position weight matrix (PWM). The database used for obtaining position frequency matrices (PFM) is JASPAR and HOCOMOCO, which is an open-access database of transcription factor binding profiles. Pseudo-counts are used while converting PFM to PWM, and TFBS detection is carried out on the basis of percent score taken as threshold value. TFIS is equipped with advanced features such as direct sequence retrieving from NCBI database using gene identification number and accession number, detecting binding site for common TF in a batch of gene sequences, and TFBS detection after generating PWM from known raw binding sequences in addition to general detection methods. TFIS can detect the presence of potential TFBSs in both the directions at the same time. This feature increases its efficiency. And the results for this dual detection are presented in different colors specific to the orientation of the binding site. Results obtained by the TFIS are more detailed and specific to the detected TFs as integration of more informative links from various related web servers are added in the result pages like Gene Ontology, PAZAR database and Transcription Factor Encyclopedia in addition to NCBI and UniProt. Common TFs like SP1, AP1 and NF-KB of the Amyloid beta precursor gene is easily detected using TFIS along with multiple binding sites. In another scenario of embryonic developmental process, TFs of the FOX family (FOXL1 and FOXC1) were also identified. TFIS is platform-independent which is publicly available along with its support and documentation at http://tfistool.appspot.com and http://www.bioinfoplus.com/tfis/ . TFIS is licensed under the GNU General Public License, version 3 (GPL-3.0).

Decentralized Interleaving of Paralleled Dc-Dc Buck Converters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Brian B; Rodriguez, Miguel; Sinha, Mohit

We present a decentralized control strategy that yields switch interleaving among parallel-connected dc-dc buck converters. The proposed method is based on the digital implementation of the dynamics of a nonlinear oscillator circuit as the controller. Each controller is fully decentralized, i.e., it only requires the locally measured output current to synthesize the pulse width modulation (PWM) carrier waveform and no communication between different controllers is needed. By virtue of the intrinsic electrical coupling between converters, the nonlinear oscillator-based controllers converge to an interleaved state with uniform phase-spacing across PWM carriers. To the knowledge of the authors, this work presents themore » first fully decentralized strategy for switch interleaving in paralleled dc-dc buck converters.« less

Adjustable speed drive study, part 1

NASA Astrophysics Data System (ADS)

Wallace, A.

1989-08-01

Advances in speed control for motors in recent years, notably those in power electronics, have widened the range of application for several adjustable speed drive (ASD) types to include the smaller horsepower sizes. The dc motor drive, formerly in almost universal use for speed control, is being challenged by the high efficiency induction motor/pulse width modulation (PWM) drive; and for special small horsepower size applications, by the permanent magnet motor/PWM inverter drive or by the switched reluctance motor drive. The main characteristics of the several ASD types suitable for small horsepower size applications are discussed, as well as their unwanted side effects: poor power factor, harmonic distortion of the supply, acoustic noise, and electromagnetic interference. A procedure is recommended for determining which, if any, ASD to use.

A study of DC-DC converters with MCT's for arcjet power supplies

NASA Technical Reports Server (NTRS)

Stuart, Thomas A.

1994-01-01

Many arcjet DC power supplies use PWM full bridge converters with large arrays of parallel FET's. This report investigates an alternative supply using a variable frequency series resonant converter with small arrays of parallel MCT's (metal oxide semiconductor controlled thyristors). The reasons for this approach are to: increase reliability by reducing the number of switching devices; and decrease the surface mounting area of the switching arrays. The variable frequency series resonant approach is used because the relatively slow switching speed of the MCT precludes the use of PWM. The 10 kW converter operated satisfactorily with an efficiency of over 91 percent. Test results indicate this efficiency could be increased further by additional optimization of the series resonant inductor.

Thin grain oriented electrical steel for PWM voltages fed magnetic cores

NASA Astrophysics Data System (ADS)

Belgrand, Thierry; Lemaître, Régis; Benabou, Abdelkader; Blaszkowski, Jonathan; Wang, Chaoyong

2018-04-01

This paper reports on performances of high permeability grain oriented electrical steel when used in association with power electronic switching devices. Loss measurement results obtained from the Epstein test, using sinusoidal or various PWM voltages in medium frequency range, show that for both studied thicknesses (HGO 0.23mm and HGO 0.18mm), comparing performances at a fixed induction level between the various situations may not be the most convenient method. The effect of magnetic domain refinement has been investigated. After having shown the interest of lowering the thickness, an alternative way of looking at losses is proposed that may help to design the magnetic core when it comes to the matter of reducing size in considering frequency and magnetization levels.

Position control of an electro-pneumatic system based on PWM technique and FLC.

PubMed

Najjari, Behrouz; Barakati, S Masoud; Mohammadi, Ali; Futohi, Muhammad J; Bostanian, Muhammad

2014-03-01

In this paper, modeling and PWM based control of an electro-pneumatic system, including the four 2-2 valves and a double acting cylinder are studied. Dynamic nonlinear behavior of the system, containing fast switching solenoid valves and a pneumatic cylinder, as well as electrical, magnetic, mechanical, and fluid subsystems are modeled. A DC-DC power converter is employed to improve solenoid valve performance and suppress system delay. Among different position control methods, a proportional integrator derivative (PID) controller and fuzzy logic controller (FLC) are evaluated. An experimental setup, using an AVR microcontroller is implemented. Simulation and experimental results verify the effectiveness of the proposed control strategies. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Core losses of an inverter-fed permanent magnet synchronous motor with an amorphous stator core under no-load

NASA Astrophysics Data System (ADS)

Denis, Nicolas; Kato, Yoshiyuki; Ieki, Masaharu; Fujisaki, Keisuke

2016-05-01

In this paper, an interior permanent magnet synchronous motor (IPMSM) with a stator core made of amorphous magnetic material (AMM) is presented. The IPMSM is driven by a voltage source three-phase inverter with classical pulse width modulation (PWM) control. The core losses under no-load condition are measured by experiment and compared to an equivalent IPMSM with a stator core made of NO steel. Under these conditions, the core losses are influenced by the stator, rotor and magnet shapes but also by the PWM carrier signal that implies a high frequency harmonic in the magnetic flux density. It is demonstrated that the AMM can reduce the core losses by about 56 %.

Jitter model and signal processing techniques for pulse width modulation optical recording

NASA Technical Reports Server (NTRS)

Liu, Max M.-K.

1991-01-01

A jitter model and signal processing techniques are discussed for data recovery in Pulse Width Modulation (PWM) optical recording. In PWM, information is stored through modulating sizes of sequential marks alternating in magnetic polarization or in material structure. Jitter, defined as the deviation from the original mark size in the time domain, will result in error detection if it is excessively large. A new approach is taken in data recovery by first using a high speed counter clock to convert time marks to amplitude marks, and signal processing techniques are used to minimize jitter according to the jitter model. The signal processing techniques include motor speed and intersymbol interference equalization, differential and additive detection, and differential and additive modulation.

A Novel Multilevel DC - AC Converter from Green Energy Power Generators Using Step-Square Waving and PWM Technique

NASA Astrophysics Data System (ADS)

Fajingbesi, F. E.; Midi, N. S.; Khan, S.

2017-06-01

Green energy sources or renewable energy system generally utilize modular approach in their design. This sort of power sources are generally in DC form or in single cases AC. Due to high fluctuation in the natural origin of this energy (wind & solar) source they are stored as DC. DC power however are difficult to transfer over long distances hence DC to AC converters and storage system are very important in green energy system design. In this work we have designed a novel multilevel DC to AC converter that takes into account the modular design of green energy systems. A power conversion efficiency of 99% with reduced total harmonic distortion (THD) was recorded from our simulated system design.

Lymphocyte responses to stress in postpartum women: relationship to vagal tone.

PubMed

Redwine, L S; Altemus, M; Leong, Y M; Carter, C S

2001-04-01

Although women spend their lives in various phases of the reproductive cycle, including menstrual, pregnancy, postpartum, lactation and menopause, few studies have examined immune responses to stress in women as a function of events associated with reproduction. The objective of this study was to evaluate differential effects of breastfeeding (n = 16), bottlefeeding (n = 10) and non-postpartum (n = 10) status on lymphocyte responses to stressful tasks (public speaking and mental arithmetic). To measure cellular immune responses, lymphocyte proliferation to plant lectins, poke weed mitogen (PWM) and phytohemagglutinin (PHA) were used. The autonomic measures, heart rate, vagal tone, blood pressure and the hormones of the HPA axis, ACTH and cortisol, were measured and their possible roles in mediating lymphocyte proliferation responses were examined. Recently parturient women who were breastfeeding or bottlefeeding had attenuated stress-induced change in lymphocyte responses to PWM compared with non-postpartum women, tested in the follicular phase of their cycle (P < 0.05). Also, lymphocyte responses to PHA were higher in the breastfeeding group compared with non-postpartum controls (P < 0.05). Regression analyses revealed that an index of cardiac vagal tone, but not other autonomic or endocrine measures, was positively predictive of lymphocyte proliferation to PWM. To summarize, these findings suggest that lactation and parturition can influence lymphocyte proliferation and that activity in the vagal system may influence lymphocyte responses to stress.

Effects of feeding pasteurized waste milk to dairy calves on phenotypes and genotypes of antimicrobial resistance in fecal Escherichia coli isolates before and after weaning.

PubMed

Maynou, G; Migura-Garcia, L; Chester-Jones, H; Ziegler, D; Bach, A; Terré, M

2017-10-01

The aim of this study was to evaluate the effects of feeding pasteurized waste milk (pWM) to calves on antimicrobial resistance of fecal Escherichia coli at both phenotypic and genotypic levels. Fifty-two Holstein female calves (3 ± 1.3 d of age) were fed 1 of the 2 different types of milk: milk replacer (MR) without antimicrobials or pWM with β-lactam residues until weaning at 49 d of age. Fecal swabs of all calves were obtained on d 0, 35, and 56 of the study and 3 E. coli isolates per sample were studied. Phenotypic resistance was tested by the disk diffusion method against a panel of 12 antimicrobials. A total of 13 resistance genes consisting of β-lactam, sulfonamide, tetracycline, and aminoglycoside families were examined by PCR. Feeding pWM to calves increased the presence of phenotypic resistance to ampicillin, cephalotin, ceftiofur, and florfenicol in fecal E. coli compared with MR-fed calves. However, the presence of resistance to sulfonamides, tetracyclines, and aminoglycosides was common in dairy calves independent of their milk-feeding source, suggesting other factors apart from the feeding source are involved in the emergence of antimicrobial resistance. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Adjustable speed drive study, June 1985 to September 1988. Part 2: Appendices

NASA Astrophysics Data System (ADS)

Wallace, Alan

1989-08-01

Advances in speed control for motors in recent years, notably those in power electronics, have widened the range of application for several adjustable speed drive (ASD) types to include the smaller horsepower sizes. The dc motor drive, formerly in almost universal use for speed control, is being challenged by the high efficiency induction motor/pulse width modulation (PWM) drive; and for special small horsepower size applications, by the permanent magnet motor/PWM inverter drive or by the switched reluctance motor drive. The main characteristics of the several ASD types suitable for small horsepower size applications are discussed, as well as their unwanted side effects: poor power factor, harmonic distortion of the supply, acoustic noise, and electromagnetic interference. A procedure is recommended for determining which, if any, ASD to use.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silva, E.R.C. da; Filho, B.J.C.

This paper presents a PWM current clamping circuit for improving a series resonant DC link converter. This circuit is capable of reducing current peaks to about 1.2--1.4 times the DC bias current. When desired, resonant transition creates notches in the dc link current, allowing the converter`s switches to synchronize with external PWM strategy. A regulated DC current source may be obtained--by using a conventional rectifier source--to feed a DC load or a current source inverter. Phase plane approach makes ease the understanding the operation, control and design procedure of the circuit. Another topology is derived and its features compared tomore » the first circuit. Simulation results for the simplified circuit and for a three-phase induction motor driven by such inverter will be presented. Moreover, the principle is corroborated by experimental results.« less

Design and test hardware for a solar array switching unit

NASA Technical Reports Server (NTRS)

Patil, A. R.; Cho, B. H.; Sable, D.; Lee, F. C.

1992-01-01

This paper describes the control of a pulse width modulated (PWM) type sequential shunt switching unit (SSU) for spacecraft applications. It is found that the solar cell output capacitance has a significant impact on SSU design. Shorting of this cell capacitance by the PWM switch causes input current surges. These surges are minimized by the use of a series filter inductor. The system with a filter is analyzed for ripple and the control to output-voltage transfer function. Stable closed loop design considerations are discussed. The results are supported by modeling and measurements of loop gain and of closed-loop bus impedance on test hardware for NASA's 120 V Earth Observation System (EOS). The analysis and modeling are also applicable to NASA's 160 V Space Station power system.

Four families with immunodeficiency and chromosome abnormalities.

PubMed Central

Candy, D C; Hayward, A R; Hughes, D T; Layward, L; Soothill, J F

1979-01-01

Six children, with severe deficiency of some or all of the immunoglobulins and minor somatic abnormalities, had chromosomal abnormalities: (1) 45,XY,t(13q/18q), (2) 46,XY,21ps +, (3) two brothers 46,XY (inv. 7) (4) 45,X,t(11p/10p)/46X,iXq,t(11p/10p) and, (5) in addendum, 45,XX,-18;46,XX, r18. The chromosome abnormalities were detected in B- as well as T-lymphocytes (as evidenced by using both PHA- and PWM-stimulated cultures) in all probands, but one was mosaic in PHA culture, although all his PWM-stimulated cells were abnormal. Chromosomal variants were also detected in relatives of three and immunodeficiency in relatives of two. Images Fig. 1 Fig. 3 PMID:314782

Wireless image-data transmission from an implanted image sensor through a living mouse brain by intra body communication

NASA Astrophysics Data System (ADS)

Hayami, Hajime; Takehara, Hiroaki; Nagata, Kengo; Haruta, Makito; Noda, Toshihiko; Sasagawa, Kiyotaka; Tokuda, Takashi; Ohta, Jun

2016-04-01

Intra body communication technology allows the fabrication of compact implantable biomedical sensors compared with RF wireless technology. In this paper, we report the fabrication of an implantable image sensor of 625 µm width and 830 µm length and the demonstration of wireless image-data transmission through a brain tissue of a living mouse. The sensor was designed to transmit output signals of pixel values by pulse width modulation (PWM). The PWM signals from the sensor transmitted through a brain tissue were detected by a receiver electrode. Wireless data transmission of a two-dimensional image was successfully demonstrated in a living mouse brain. The technique reported here is expected to provide useful methods of data transmission using micro sized implantable biomedical sensors.

Performance of High-Speed PWM Control Chips at Cryogenic Temperatures

NASA Technical Reports Server (NTRS)

Elbuluk, Malik E.; Gerber, Scott; Hammoud, Ahmad; Patterson, Richard; Overton, Eric

2001-01-01

The operation of power electronic systems at cryogenic temperatures is anticipated in many NASA space missions such as planetary exploration and deep space probes. In addition to surviving the space hostile environment, electronics capable of low temperature operation would contribute to improving circuit performance, increasing system efficiency, and reducing development and launch costs. As part of the NASA Glenn Low Temperature Electronics Program, several commercial high-speed Pulse Width Modulation (PWM) chips have been characterized in terms of their performance as a function of temperature in the range of 25 to -196 C (liquid nitrogen). These chips ranged in their electrical characteristics, modes of control, packaging options, and applications. The experimental procedures along with the experimental data obtained on the investigated chips are presented and discussed.

Multilevel-Dc-Bus Inverter For Providing Sinusoidal And Pwm Electrical Machine Voltages

DOEpatents

Su, Gui-Jia [Knoxville, TN

2005-11-29

A circuit for controlling an ac machine comprises a full bridge network of commutation switches which are connected to supply current for a corresponding voltage phase to the stator windings, a plurality of diodes, each in parallel connection to a respective one of the commutation switches, a plurality of dc source connections providing a multi-level dc bus for the full bridge network of commutation switches to produce sinusoidal voltages or PWM signals, and a controller connected for control of said dc source connections and said full bridge network of commutation switches to output substantially sinusoidal voltages to the stator windings. With the invention, the number of semiconductor switches is reduced to m+3 for a multi-level dc bus having m levels. A method of machine control is also disclosed.

Methods, systems and apparatus for controlling operation of two alternating current (AC) machines

DOEpatents

Gallegos-Lopez, Gabriel [Torrance, CA; Nagashima, James M [Cerritos, CA; Perisic, Milun [Torrance, CA; Hiti, Silva [Redondo Beach, CA

2012-02-14

A system is provided for controlling two AC machines. The system comprises a DC input voltage source that provides a DC input voltage, a voltage boost command control module (VBCCM), a five-phase PWM inverter module coupled to the two AC machines, and a boost converter coupled to the inverter module and the DC input voltage source. The boost converter is designed to supply a new DC input voltage to the inverter module having a value that is greater than or equal to a value of the DC input voltage. The VBCCM generates a boost command signal (BCS) based on modulation indexes from the two AC machines. The BCS controls the boost converter such that the boost converter generates the new DC input voltage in response to the BCS. When the two AC machines require additional voltage that exceeds the DC input voltage required to meet a combined target mechanical power required by the two AC machines, the BCS controls the boost converter to drive the new DC input voltage generated by the boost converter to a value greater than the DC input voltage.

Modified Perfect Harmonics Cancellation Control of a Grid Interfaced SPV Power Generation

NASA Astrophysics Data System (ADS)

Singh, B.; Shahani, D. T.; Verma, A. K.

2015-03-01

This paper deals with a grid interfaced solar photo voltaic (SPV) power generating system with modified perfect harmonic cancellation (MPHC) control for power quality improvement in terms of mitigation of the current harmonics, power factor correction, control of point of common coupling (PCC) voltage with reactive power compensation and load balancing in a three phase distribution system. The proposed grid interfaced SPV system consists of a SPV array, a dc-dc boost converter and a voltage source converter (VSC) used for the compensation of other connected linear and nonlinear loads at PCC. The reference grid currents are estimated using MPHC method and control signals are derived by using pulse width modulation (PWM) current controller of VSC. The SPV power is fed to the common dc bus of VSC and dc-dc boost converter using maximum power point tracking (MPPT). The dc link voltage of VSC is regulated by using dc voltage proportional integral (PI) controller. The analysis of the proposed SPV power generating system is carried out under dc/ac short circuit and severe SPV-SX and SPV-TX intrusion.

GRC-2013-C-02448

NASA Image and Video Library

2009-06-23

Environmental Portrait, Electrical Power Systems Employee, hardware for the High Power 300-Volt Power Processing Unit (PPU). The Printed Circuit Boards (PCBs) are the Discharge Module Inverter and the Pulse Width Modulation (PWM) Controller

Simulation comparison of proportional integral derivative and fuzzy logic in controlling AC-DC buck boost converter

NASA Astrophysics Data System (ADS)

Faisal, A.; Hasan, S.; Suherman

2018-03-01

AC-DC converter is widely used in the commercial industry even for daily purposes. The AC-DC converter is used to convert AC voltage into DC. In order to obtain the desired output voltage, the converter usually has a controllable regulator. This paper discusses buck boost regulator with a power MOSFET as switching component which is adjusted based on the duty cycle of pulse width modulation (PWM). The main problems of the buck boost converter at start up are the high overshoot, the long peak time and rise time. This paper compares the effectiveness of two control techniques: proportional integral derivative (PID) and fuzzy logic control in controlling the buck boost converter through simulations. The results show that the PID is more sensitive to voltage change than fuzzy logic. However, PID generates higher overshoot, long peak time and rise time. On the other hand, fuzzy logic generates no overshoot and shorter rise time.

Optically powered oil tank multichannel detection system with optical fiber link

NASA Astrophysics Data System (ADS)

Yu, Zhijing

1998-08-01

A novel oil tanks integrative parameters measuring system with optically powered are presented. To realize optical powered and micro-power consumption multiple channels and parameters detection, the system has taken the PWM/PPM modulation, ratio measurement, time division multiplexing and pulse width division multiplexing techniques. Moreover, the system also used special pulse width discriminator and single-chip microcomputer to accomplish signal pulse separation, PPM/PWM signal demodulation, the error correction of overlapping pulse and data processing. This new transducer has provided with high characteristics: experimental transmitting distance is 500m; total consumption of the probes is less than 150 (mu) W; measurement error: +/- 0.5 degrees C and +/- 0.2 percent FS. The measurement accuracy of the liquid level and reserves is mainly determined by the pressure accuracy. Finally, some points of the experiment are given.

Optimized Signaling Method for High-Speed Transmission Channels with Higher Order Transfer Function

NASA Astrophysics Data System (ADS)

Ševčík, Břetislav; Brančík, Lubomír; Kubíček, Michal

2017-08-01

In this paper, the selected results from testing of optimized CMOS friendly signaling method for high-speed communications over cables and printed circuit boards (PCBs) are presented and discussed. The proposed signaling scheme uses modified concept of pulse width modulated (PWM) signal which enables to better equalize significant channel losses during data high-speed transmission. Thus, the very effective signaling method to overcome losses in transmission channels with higher order transfer function, typical for long cables and multilayer PCBs, is clearly analyzed in the time and frequency domain. Experimental results of the measurements include the performance comparison of conventional PWM scheme and clearly show the great potential of the modified signaling method for use in low power CMOS friendly equalization circuits, commonly considered in modern communication standards as PCI-Express, SATA or in Multi-gigabit SerDes interconnects.

Weighted LCS

NASA Astrophysics Data System (ADS)

Amir, Amihood; Gotthilf, Zvi; Shalom, B. Riva

The Longest Common Subsequence (LCS) of two strings A and B is a well studied problem having a wide range of applications. When each symbol of the input strings is assigned a positive weight the problem becomes the Heaviest Common Subsequence (HCS) problem. In this paper we consider a different version of weighted LCS on Position Weight Matrices (PWM). The Position Weight Matrix was introduced as a tool to handle a set of sequences that are not identical, yet, have many local similarities. Such a weighted sequence is a 'statistical image' of this set where we are given the probability of every symbol's occurrence at every text location. We consider two possible definitions of LCS on PWM. For the first, we solve the weighted LCS problem of z sequences in time O(zn z + 1). For the second, we prove \\cal{NP}-hardness and provide an approximation algorithm.

Stimulation of Chronic Lymphocytic Leukemia (CLL) Cells with CpG Oligodeoxynucleotide (ODN) Gives Consistent Karyotypic Results among Laboratories: a CLL Research Consortium (CRC)h Study

PubMed Central

Heerema, Nyla A.; Byrd, John C.; Cin, Paola Dal; Dell’ Aquila, Marie L.; Koduru, Prasad; Aviram, Ayala; Smoley, Stephanie; Rassenti, Laura Z.; Greaves, Andrew W.; Brown, Jennifer R.; Rai, Kanti R.; Kipps, Thomas J.; Kay, Neil E.; van Dyke, Daniel

2010-01-01

Cytogenetic abnormalities in CLL are important prognostic indicators. Historically, only interphase cytogenetics was clinically useful in CLL because traditional mitogens are not effective mitotic stimulants. Recently, CpG-oligodeoxynucleotide (ODN) stimulation has shown effectiveness in CLL. The CLL Research Consortium (CRC) tested the effectiveness and reproducibility of CpG-ODN stimulation to detect chromosomally abnormal clones by five laboratories. More clonal abnormalities were observed after culture of CLL cells with CpG-ODN than with pokeweed mitogen (PWM)+12-O-tetradecanoyl-phorobol-13-acetate (TPA). All clonal abnormalities in PWM+TPA cultures were observed in CpG-ODN cultures, whereas CpG-ODN identified some clones not found by PWM+TPA. CpG-ODN stimulation of one normal control and 12 CLL samples showed that excepting clones of del(13q) in low frequencies and one translocation, results in all five laboratories were consistent, and all abnormalities were concordant with FISH. Thus, abnormal clones in CLL are more readily detected with CpG-ODN stimulation than with traditional B-cell mitogens. After CpG-ODN stimulation, abnormalities were reproducible among cytogenetic laboratories. CpG-ODN did not appear to induce aberrations in cell culture and enhanced detection of abnormalities and complexity in CLL. Since karyotypic complexity is prognostic and is not detectable by standard FISH analyses, stimulation with CpG-ODN is useful to identify this additional prognostic factor in CLL. PMID:21156225

The Role of Phonological Working Memory and Environmental Factors in Lexical Development in Italian-Speaking Late Talkers: A One-Year Follow-Up Study.

PubMed

Marini, Andrea; Ruffino, Milena; Sali, Maria Enrica; Molteni, Massimo

2017-12-20

This follow-up study assessed (a) the influence of phonological working memory (pWM), home literacy environment, and a family history of linguistic impairments in late talkers (LTs); (b) the diagnostic accuracy of a task of nonword repetition (NWR) in identifying LTs; and (c) the persistence of lexical weaknesses after 10 months. Two hundred ninety-three children were assessed at approximately 32 (t1) and 41 (t2) months. At t1, they were administered the Italian adaptation of the Language Development Survey, an NWR task (used to assess pWM), and questionnaires assessing home literacy environment and family history of language impairments. Thirty-three LTs were identified. The linguistic skills of the participants were evaluated at t2 by administering tasks assessing Articulation, Naming, Semantic Fluency, and Lexical Comprehension. At t2, LTs performed more poorly as compared with age-matched typically developing peers in articulatory and naming skills, had reduced lexical comprehension abilities, and had limited lexical knowledge. Their performance on the NWR task at t1 correlated with the extension of their vocabularies at t2 (as estimated with a Semantic Fluency task). The Language Development Survey recently adapted to Italian is sensitive to LTs. Former LTs still have a mild lexical delay at approximately 40 months. As an indirect measure of pWM, the task of NWR is an early indicator of future lexical deficits.

Sensorless control for a sophisticated artificial myocardial contraction by using shape memory alloy fibre.

PubMed

Shiraishi, Y; Yambe, T; Saijo, Y; Sato, F; Tanaka, A; Yoshizawa, M; Sugai, T K; Sakata, R; Luo, Y; Park, Y; Uematsu, M; Umezu, M; Fujimoto, T; Masumoto, N; Liu, H; Baba, A; Konno, S; Nitta, S; Imachi, K; Tabayashi, K; Sasada, H; Homma, D

2008-01-01

The authors have been developing an artificial myocardium, which is capable of supporting natural contractile function from the outside of the ventricle. The system was originally designed by using sophisticated covalent shape memory alloy fibres, and the surface did not implicate blood compatibility. The purpose of our study on the development of artificial myocardium was to achieve the assistance of myocardial functional reproduction by the integrative small mechanical elements without sensors, so that the effective circulatory support could be accomplished. In this study, the authors fabricated the prototype artificial myocardial assist unit composed of the sophisticated shape memory alloy fibre (Biometal), the diameter of which was 100 microns, and examined the mechanical response by using pulse width modulation (PWM) control method in each unit. Prior to the evaluation of dynamic characteristics, the relationship between strain and electric resistance and also the initial response of each unit were obtained. The component for the PWM control was designed in order to regulate the myocardial contractile function, which consisted of an originally-designed RISC microcomputer with the input of displacement, and its output signal was controlled by pulse wave modulation method. As a result, the optimal PWM parameters were confirmed and the fibrous displacement was successfully regulated under the different heat transfer conditions simulating internal body temperature as well as bias tensile loading. Then it was indicated that this control theory might be applied for more sophisticated ventricular passive or active restraint by the artificial myocardium on physiological demand.

An Inductively-Powered Wireless Neural Recording System with a Charge Sampling Analog Front-End

PubMed Central

Lee, Seung Bae; Lee, Byunghun; Kiani, Mehdi; Mahmoudi, Babak; Gross, Robert; Ghovanloo, Maysam

2015-01-01

An inductively-powered wireless integrated neural recording system (WINeR-7) is presented for wireless and battery less neural recording from freely-behaving animal subjects inside a wirelessly-powered standard homecage. The WINeR-7 system employs a novel wide-swing dual slope charge sampling (DSCS) analog front-end (AFE) architecture, which performs amplification, filtering, sampling, and analog-to-time conversion (ATC) with minimal interference and small amount of power. The output of the DSCS-AFE produces a pseudo-digital pulse width modulated (PWM) signal. A circular shift register (CSR) time division multiplexes (TDM) the PWM pulses to create a TDM-PWM signal, which is fed into an on-chip 915 MHz transmitter (Tx). The AFE and Tx are supplied at 1.8 V and 4.2 V, respectively, by a power management block, which includes a high efficiency active rectifier and automatic resonance tuning (ART), operating at 13.56 MHz. The 8-ch system-on-a-chip (SoC) was fabricated in a 0.35-μm CMOS process, occupying 5.0 × 2.5 mm2 and consumed 51.4 mW. For each channel, the sampling rate is 21.48 kHz and the power consumption is 19.3 μW. In vivo experiments were conducted on freely behaving rats in an energized homecage by continuously delivering 51.4 mW to the WINeR-7 system in a closed-loop fashion and recording local field potentials (LFP). PMID:27069422

An Inductively-Powered Wireless Neural Recording System with a Charge Sampling Analog Front-End.

PubMed

Lee, Seung Bae; Lee, Byunghun; Kiani, Mehdi; Mahmoudi, Babak; Gross, Robert; Ghovanloo, Maysam

2016-01-15

An inductively-powered wireless integrated neural recording system (WINeR-7) is presented for wireless and battery less neural recording from freely-behaving animal subjects inside a wirelessly-powered standard homecage. The WINeR-7 system employs a novel wide-swing dual slope charge sampling (DSCS) analog front-end (AFE) architecture, which performs amplification, filtering, sampling, and analog-to-time conversion (ATC) with minimal interference and small amount of power. The output of the DSCS-AFE produces a pseudo-digital pulse width modulated (PWM) signal. A circular shift register (CSR) time division multiplexes (TDM) the PWM pulses to create a TDM-PWM signal, which is fed into an on-chip 915 MHz transmitter (Tx). The AFE and Tx are supplied at 1.8 V and 4.2 V, respectively, by a power management block, which includes a high efficiency active rectifier and automatic resonance tuning (ART), operating at 13.56 MHz. The 8-ch system-on-a-chip (SoC) was fabricated in a 0.35-μm CMOS process, occupying 5.0 × 2.5 mm 2 and consumed 51.4 mW. For each channel, the sampling rate is 21.48 kHz and the power consumption is 19.3 μW. In vivo experiments were conducted on freely behaving rats in an energized homecage by continuously delivering 51.4 mW to the WINeR-7 system in a closed-loop fashion and recording local field potentials (LFP).

Experimental studies on twin PTCs driven by dual piston head linear compressor

NASA Astrophysics Data System (ADS)

Gour, Abhay S.; Joy, Joewin; Sagar, Pankaj; Sudharshan, H.; Mallappa, A.; Karunanithi, R.; Jacob, S.

2017-02-01

An experimental study on pulse tube cryocooler is presented with a twin pulse tube configuration. The study is conducted with a dual piston head linear compressor design which is developed indigenously. The two identical pulse tube cryocoolers are operated by a single linear motor which generates 1800 out of phase dual pressure waves. The advantages of the configuration being the reduction in fabrication cost and the increased cooling power. The compressor is driven at a frequency of 48 Hz using indigenously developed PWM based power supply. The CFD study of pulse tube cryocooler is discussed along with the experimental cool down results. A detailed experimental and FEM based studies on the fabrication procedure of heat exchangers is conducted to ensure better heat transfer in the same.

FEM analysis of an single stator dual PM rotors axial synchronous machine

NASA Astrophysics Data System (ADS)

Tutelea, L. N.; Deaconu, S. I.; Popa, G. N.

2017-01-01

The actual e - continuously variable transmission (e-CVT) solution for the parallel Hybrid Electric Vehicle (HEV) requires two electric machines, two inverters, and a planetary gear. A distinct electric generator and a propulsion electric motor, both with full power converters, are typical for a series HEV. In an effort to simplify the planetary-geared e-CVT for the parallel HEV or the series HEV we hereby propose to replace the basically two electric machines and their two power converters by a single, axial-air-gap, electric machine central stator, fed from a single PWM converter with dual frequency voltage output and two independent PM rotors. The proposed topologies, the magneto-motive force analysis and quasi 3D-FEM analysis are the core of the paper.

Generating Quitline calls during Australia's National Tobacco Campaign: effects of television advertisement execution and programme placement

PubMed Central

Carroll, T; Rock, B

2003-01-01

Objective: The study sought to measure the relative efficiency of different television advertisements and types of television programmes in which advertisements were placed, in generating calls to Australia's national Quitline. Design: The study entailed an analysis of the number of calls generated to the Quitline relative to the weight of advertising exposure (in target audience rating points (TARPs) for particular television advertisements and for placement of these advertisements in particular types of television programmes. A total of 238 television advertisement placements and 1769 calls to the Quitline were analysed in Sydney and Melbourne. Results: The more graphic "eye" advertisement conveying new information about the association between smoking and macular degeneration leading to blindness was more efficient in generating quitline calls than the "tar" advertisement, which reinforced the message of tar in a smoker's lungs. Combining the health effects advertisements with a quitline modelling advertisement tended to increase the efficiency of generating Quitline calls. Placing advertisements in lower involvement programmes appears to provide greater efficiency in generating Quitline calls than in higher involvement programmes. Conclusions: Tobacco control campaign planners can increase the number of calls to telephone quitlines by assessing the efficiency of particular advertisements to generate such calls. Pairing of health effect and quitline modelling advertisements can increase efficiency in generating calls. Placement of advertisements in lower involvement programme types may increase efficiency in generating Quitline calls. PMID:12878772

Generating Quitline calls during Australia's National Tobacco Campaign: effects of television advertisement execution and programme placement.

PubMed

Carroll, T; Rock, B

2003-09-01

The study sought to measure the relative efficiency of different television advertisements and types of television programmes in which advertisements were placed, in generating calls to Australia's national Quitline. The study entailed an analysis of the number of calls generated to the Quitline relative to the weight of advertising exposure (in target audience rating points (TARPs) for particular television advertisements and for placement of these advertisements in particular types of television programmes. A total of 238 television advertisement placements and 1769 calls to the Quitline were analysed in Sydney and Melbourne. The more graphic "eye" advertisement conveying new information about the association between smoking and macular degeneration leading to blindness was more efficient in generating quitline calls than the "tar" advertisement, which reinforced the message of tar in a smoker's lungs. Combining the health effects advertisements with a quitline modelling advertisement tended to increase the efficiency of generating Quitline calls. Placing advertisements in lower involvement programmes appears to provide greater efficiency in generating Quitline calls than in higher involvement programmes. Tobacco control campaign planners can increase the number of calls to telephone quitlines by assessing the efficiency of particular advertisements to generate such calls. Pairing of health effect and quitline modelling advertisements can increase efficiency in generating calls. Placement of advertisements in lower involvement programme types may increase efficiency in generating Quitline calls.

A design of LED adaptive dimming lighting system based on incremental PID controller

NASA Astrophysics Data System (ADS)

He, Xiangyan; Xiao, Zexin; He, Shaojia

2010-11-01

As a new generation energy-saving lighting source, LED is applied widely in various technology and industry fields. The requirement of its adaptive lighting technology is more and more rigorous, especially in the automatic on-line detecting system. In this paper, a closed loop feedback LED adaptive dimming lighting system based on incremental PID controller is designed, which consists of MEGA16 chip as a Micro-controller Unit (MCU), the ambient light sensor BH1750 chip with Inter-Integrated Circuit (I2C), and constant-current driving circuit. A given value of light intensity required for the on-line detecting environment need to be saved to the register of MCU. The optical intensity, detected by BH1750 chip in real time, is converted to digital signal by AD converter of the BH1750 chip, and then transmitted to MEGA16 chip through I2C serial bus. Since the variation law of light intensity in the on-line detecting environment is usually not easy to be established, incremental Proportional-Integral-Differential (PID) algorithm is applied in this system. Control variable obtained by the incremental PID determines duty cycle of Pulse-Width Modulation (PWM). Consequently, LED's forward current is adjusted by PWM, and the luminous intensity of the detection environment is stabilized by self-adaptation. The coefficients of incremental PID are obtained respectively after experiments. Compared with the traditional LED dimming system, it has advantages of anti-interference, simple construction, fast response, and high stability by the use of incremental PID algorithm and BH1750 chip with I2C serial bus. Therefore, it is suitable for the adaptive on-line detecting applications.

Design of an Internal Model Control strategy for single-phase grid-connected PWM inverters and its performance analysis with a non-linear local load and weak grid.

PubMed

Chaves, Eric N; Coelho, Ernane A A; Carvalho, Henrique T M; Freitas, Luiz C G; Júnior, João B V; Freitas, Luiz C

2016-09-01

This paper presents the design of a controller based on Internal Model Control (IMC) applied to a grid-connected single-phase PWM inverter. The mathematical modeling of the inverter and the LCL output filter, used to project the 1-DOF IMC controller, is presented and the decoupling of grid voltage by a Feedforward strategy is analyzed. A Proportional - Resonant Controller (P+Res) was used for the control of the same plant in the running of experimental results, thus moving towards the discussion of differences regarding IMC and P+Res performances, which arrived at the evaluation of the proposed control strategy. The results are presented for typical conditions, for weak-grid and for non-linear local load, in order to verify the behavior of the controller against such situations. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

A New Type Hi-Speed BLDC Control System Base on Indirect Current Control Strategy

NASA Astrophysics Data System (ADS)

Wang, D. P.; Wang, Y. C.; Zhang, F. G.; Jin, S.

2017-05-01

High speed BLDC has the characteristic as larger air gap smaller armature inductance, traditional PWM modulation will produce a great number of high frequency current harmonics which led problem like large torque ripple and serious motor heat. In the meantime traditional PWM modulation use the diode rectifier which cause harmonic pollution in electric power net. To solve the problem above, proposes a new motor controller topology. Using the IGBT device to replace the diode on frequency converter rectifier side, apply the power factor correction technology, reduce the pollution on the grid. Using busbar current modulation on the inverter, driving bridge-arm use 3-phase 6-state open as driving Mode, realize the control on a 10000r/min,10kw BLDC. The results of Simulation on matlab show the topological structure as proposed can effectively improve the network side power factor and reduce the motor armature winding harmonic and motor torque ripple.

Understanding young and older male drivers' willingness to drive while intoxicated: the predictive utility of constructs specified by the theory of planned behaviour and the prototype willingness model.

PubMed

Rivis, Amanda; Abraham, Charles; Snook, Sarah

2011-05-01

The present study examined the predictive utility of constructs specified by the theory of planned behaviour (TPB) and prototype willingness model (PWM) for young and older male drivers' willingness to drive while intoxicated. A cross-sectional questionnaire was employed. Two hundred male drivers, recruited via a street survey, voluntarily completed measures of attitude, subjective norm, perceived behavioural control, prototype perceptions, and willingness. Findings showed that the TPB and PWM variables explained 65% of the variance in young male drivers' willingness and 47% of the variance in older male drivers' willingness, with the interaction between prototype favourability and similarity contributing 7% to the variance explained in older males' willingness to drive while intoxicated. The findings possess implications for theory, research, and anti-drink driving campaigns. ©2010 The British Psychological Society.

Motif discovery and motif finding from genome-mapped DNase footprint data.

PubMed

Kulakovskiy, Ivan V; Favorov, Alexander V; Makeev, Vsevolod J

2009-09-15

Footprint data is an important source of information on transcription factor recognition motifs. However, a footprinting fragment can contain no sequences similar to known protein recognition sites. Inspection of genome fragments nearby can help to identify missing site positions. Genome fragments containing footprints were supplied to a pipeline that constructed a position weight matrix (PWM) for different motif lengths and selected the optimal PWM. Fragments were aligned with the SeSiMCMC sampler and a new heuristic algorithm, Bigfoot. Footprints with missing hits were found for approximately 50% of factors. Adding only 2 bp on both sides of a footprinting fragment recovered most hits. We automatically constructed motifs for 41 Drosophila factors. New motifs can recognize footprints with a greater sensitivity at the same false positive rate than existing models. Also we discuss possible overfitting of constructed motifs. Software and the collection of regulatory motifs are freely available at http://line.imb.ac.ru/DMMPMM.

Analytical modeling of eddy-current losses caused by pulse-width-modulation switching in permanent-magnet brushless direct-current motors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, F.; Nehl, T.W.

1998-09-01

Because of their high efficiency and power density the PM brushless dc motor is a strong candidate for electric and hybrid vehicle propulsion systems. An analytical approach is developed to predict the inverter high frequency pulse width modulation (PWM) switching caused eddy-current losses in a permanent magnet brushless dc motor. The model uses polar coordinates to take curvature effects into account, and is also capable of including the space harmonic effect of the stator magnetic field and the stator lamination effect on the losses. The model was applied to an existing motor design and was verified with the finite elementmore » method. Good agreement was achieved between the two approaches. Hence, the model is expected to be very helpful in predicting PWM switching losses in permanent magnet machine design.« less

PWM Inverter control and the application thereof within electric vehicles

DOEpatents

Geppert, Steven

1982-01-01

An inverter (34) which provides power to an A.C. machine (28) is controlled by a circuit (36) employing PWM control strategy whereby A.C. power is supplied to the machine at a preselectable frequency and preselectable voltage. This is accomplished by the technique of waveform notching in which the shapes of the notches are varied to determine the average energy content of the overall waveform. Through this arrangement, the operational efficiency of the A.C. machine is optimized. The control circuit includes a micro-computer and memory element which receive various parametric inputs and calculate optimized machine control data signals therefrom. The control data is asynchronously loaded into the inverter through an intermediate buffer (38). In its preferred embodiment, the present invention is incorporated within an electric vehicle (10) employing a 144 VDC battery pack (32) and a three-phase induction motor (18).

Vibration and acoustic noise emitted by dry-type air-core reactors under PWM voltage excitation

NASA Astrophysics Data System (ADS)

Li, Jingsong; Wang, Shanming; Hong, Jianfeng; Yang, Zhanlu; Jiang, Shengqian; Xia, Shichong

2018-05-01

According to coupling way between the magnetic field and the structural order, structure mode is discussed by engaging finite element (FE) method and both natural frequency and modal shape for a dry-type air-core reactor (DAR) are obtained in this paper. On the basis of harmonic response analysis, electromagnetic force under PWM (Pulse Width Modulation) voltage excitation is mapped with the structure mesh, the vibration spectrum is gained and the consequences represents that the whole structure vibration predominates in the radial direction, with less axial vibration. Referring to the test standard of reactor noise, the rules of emitted noise of the DAR are measured and analyzed at chosen switching frequency matches the sample resonant frequency and the methods of active vibration and noise reduction are put forward. Finally, the low acoustic noise emission of a prototype DAR is verified by measurement.

A HIGH BANDWIDTH BIPOLAR POWER SUPPLY FOR THE FAST CORRECTORS IN THE APS UPGRADE*

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Ju; Sprau, Gary

The APS Upgrade of a multi-bend achromat (MBA) storage ring requires a fast bipolar power supply for the fast correction magnets. The key performance requirement of the power supply includes a small-signal bandwidth of 10 kHz for the output current. This requirement presents a challenge to the design because of the high inductance of the magnet load and a limited input DC voltage. A prototype DC/DC power supply utilizing a MOSFET H-bridge circuit with a 500 kHz PWM has been developed and tested successfully. The prototype achieved a 10-kHz bandwidth with less than 3-dB attenuation for a signal 0.5% ofmore » the maximum operating current of 15 amperes. This paper presents the design of the power circuit, the PWM method, the control loop, and the test results.« less

Age differences in alcohol prototype perceptions and willingness to drink in U.K. adolescents.

PubMed

Davies, Emma L; Martin, Jilly; Foxcroft, David R

2016-01-01

Using the prototype willingness model (PWM) as a framework, this study sought to explore the relationship between prototype perceptions, willingness and alcohol consumption in a sample of adolescents in the United Kingdom (UK). Adolescents aged 11-17 were asked about their alcohol prototype perceptions, willingness to drink, intentions, alcohol consumption, drunkenness and harms using a cross-sectional online survey. Participants were recruited through opportunity sampling via schools and parents. The survey was completed by 178 respondents (51% female; 91 aged 11-15, 87 aged 16-17). Multivariate analysis revealed significant differences between participants aged 11-15 and 16-17 on PWM measures, even when experience with drinking was accounted for (p < .001). There were significant interactions (p < .001) between age and prototype perceptions; younger participants rated non-drinker prototypes as more favourable and more similar to the self than 16- and 17-year-old participants. Willingness and intentions interacted with age; both measures were similar in 16- and 17-year-olds, whereas younger participants scored significantly higher on willingness than intentions (p < .001). Three distinct scales of prototype descriptions were identified in principal components analysis. Characteristics related to sociability significantly predicted willingness to drink alcohol in the sample (p < .001). This study extends previous research by demonstrating that the PWM can provide a theoretical explanation of adolescent drinking in the UK. The results suggest that 11- to 15-year-olds may be the most suitable age for an intervention that targets alcohol prototypes, with a focus on sociability characteristics.

Temperature-stabilized, narrowband tunable fiber-Bragg gratings for matched-filter receiver

NASA Astrophysics Data System (ADS)

Roth, Jeffrey M.; Kummer, Joseph W.; Minch, Jeffrey R.; Malinsky, Bryan G.; Scalesse, Vincent; Walther, Frederick G.

2017-02-01

We report on a 1550-nm matched filter based on a pair of fiber Bragg gratings (FBGs) that is actively stabilized over temperature. The filter is constructed of a cascaded pair of athermally-packaged FBGs. The tandem FBG pair produces an aggregate 3-dB bandwidth of 3.9-GHz that is closely matched to a return-to-zero, 2.880-GHz differential-phase-shift-keyed optical waveform. The FBGs comprising the filter are controlled in wavelength using a custom-designed, pulse-width modulation (PWM) heater controller. The controllers allow tuning of the FBGs over temperature to compensate and cancel out native temperature dependence of the athermal FBG (AFBG) package. Two heaters are bonded to each FBG device, one on each end. One heater is a static offset that biases the FBG wavelength positively. The second heater is a PWM controller that actively moves the FBG wavelength negatively. A temperature sensor measures the FBGs' temperature, and a feed-forward control loop adjusts the PWM signal to hold the wavelength within a desired range. This stabilization technique reduces the device's native temperature dependence from approximately 0.65 pm/°C to 0.06 pm/°C, improving the temperature stability by tenfold, while retaining some control for poten- tial long-term drifts. The technique demonstrates that the FBGs can be held to +/-1.5 pm (+/-188 MHz) of the target wavelength over a 0 to +50°C temperature range. The temperature-stabilized FBGs are integrated into a low-noise, optical pre-amplifier that operates over a wide temperature range for a laser communication system.

Climatology of monsoon precipitation over the Tibetan Plateau from 13-year TRMM observations

NASA Astrophysics Data System (ADS)

Aijuan, Bai; Guoping, Li

2016-10-01

Based on the 13-year data from the Tropical Rainfall Measuring Mission (TRMM) satellite during 2001-2013, the influencing geographical location of the Tibetan Plateau (Plateau) monsoon is determined. It is found that the domain of the Plateau monsoon is bounded by the latitude between 27° N and 37° N and the longitude between 60° E and 103° E. According to the annual relative precipitation, the Plateau monsoon can be divided into three sections: the Plateau winter monsoon (PWM) over Iran and Afghanistan, the Plateau summer monsoon (PSM) over the central Plateau, and the transiting zone of the Plateau monsoon (TPM) over the south, west, and east edges of the Plateau. In PWM and PSM, the monsoon climatology has a shorter rainy season with the mean annual rainfall of less than 800 mm. In TPM, it has a longer rainy season with the mean annual rainfall of more than 1800 mm. PWM experiences a single-peak monthly rainfall with the peak during January to March; PSM usually undergoes a multi-peak pattern with peaks in the warm season; TPM presents a double-peak pattern, with a strong peak in late spring to early summer and a secondary peak in autumn. The Plateau monsoon also characterizes an asymmetrical seasonal advance of the rain belt. In the east of the Plateau, the rain belt migrates in a south-north orientation under the impact of the tropical and subtropical systems' oscillation. In the west of the Plateau, the rain belt advances in an east-west direction, which is mainly controlled by the regional Plateau monsoon.

Assessing "Me Generation's" Entrepreneurship Degree Programmes in Malaysia

ERIC Educational Resources Information Center

Zainuddin, Muhammad Nizam; Rejab, Mohd Rozaini Mohd

2010-01-01

Purpose: The purpose of this paper is to assess the effectiveness of undergraduates' specialised entrepreneurship programmes in Malaysian universities that have been made available to "ME generation" students. By analysing the antecedents and predicting self-employment intention, the paper evaluates the impact of such programmes upon the…

T suppressor cells are required for the maintenance of the antigen-induced B-cell unresponsive state in humans

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benveniste, E.; Stevens, R.H.

1983-04-01

Tetanus toxoid immunization of humans generates circulating B cells which secrete IgG anti-tetanus toxoid antibodies (IgG-Tet) when stimulated in vitro with T cells and pokeweed mitogen (PWM). A unique property of these cells is the inhibition of maturation into antibody-secreting plasma cells following a 1-hr in vitro pulse with tetanus toxoid. Studies were undertaken to determine if different T-cell subsets could modulate the in vitro generated B-cell unresponsive state. The addition of OKT4+/OKT8- cells to antigen-treated B cells resulted in a partial reversal of the antigen-induced inhibition of IgG-Tet synthesis. The addition of OKT4-/OKT8+ cells to the treated B cellsmore » caused a suppression of IgG-Tet synthesis comparable to that seen in cultures containing unfractionated T cells. These results indicate that (1) the B-cell unresponsive state generated by antigen treatment is not absolute, (2) the degree of B-cell unresponsiveness results from a balance of suppressor and helper signals, and (3) T-suppressor cells need to be present to induce and maintain the B-cell unresponsive state.« less

Programmable pulse generator based on programmable logic and direct digital synthesis.

PubMed

Suchenek, M; Starecki, T

2012-12-01

The paper presents a new approach of pulse generation which results in both wide range tunability and high accuracy of the output pulses. The concept is based on the use of programmable logic and direct digital synthesis. The programmable logic works as a set of programmable counters, while direct digital synthesis (DDS) as the clock source. Use of DDS as the clock source results in stability of the output pulses comparable to the stability of crystal oscillators and quasi-continuous tuning of the output frequency.

Hardware and circuit design of a vibrational cleaner

NASA Astrophysics Data System (ADS)

Fhong Soon, Chin; Thong, Kok Tung; Sek Tee, Kian; Nayan, Nafarizal; Khairul Ahmad, Mohd; Nurashikin Nordin, Anis

2016-11-01

Microtissue can be grown on soft substrates of hydrogel or liquid crystal gel. These gels are adherent to the microtissues and they may interfere fluorescence imaging as background noise due to their absorbance property. A microfluidic vibrational cleaner with polydimethylsiloxane (PDMS) microfluidic chip platform was proposed and developed to remove the residual gel of liquid crystal adhered to the microtissues. The microtissues were placed in a microfluidic chip attaching to a microfluidic vibrational platform. In the system design, two motorised vibrators vibrating attached to a microfluidic platform and generating vibration signals at 148 Hz and 0.89 Grms to clean the microtissues. The acceleration of the vibration increased gradually from 0 to 0.96 Grms when the duty cycle of PWM pulses increased from 50 - 90%. It dropped slightly to 0.89 Grms at 100% duty cycle. Irrigation water valve was designed to control the fluid flow from water pump during cleaning process. Water pumps were included to flush the channels of the microfluidic device. The signals in controlling the pump, motor and valve were linearly proportional to the duty cycles of the pulse width modulation signals generated from a microcontroller.

Improved direct torque control of an induction generator used in a wind conversion system connected to the grid.

PubMed

Abdelli, Radia; Rekioua, Djamila; Rekioua, Toufik; Tounzi, Abdelmounaïm

2013-07-01

This paper presents a modulated hysteresis direct torque control (MHDTC) applied to an induction generator (IG) used in wind energy conversion systems (WECs) connected to the electrical grid through a back-to-back converter. The principle of this strategy consists in superposing to the torque reference a triangular signal, as in the PWM strategy, with the desired switching frequency. This new modulated reference is compared to the estimated torque by using a hysteresis controller as in the classical direct torque control (DTC). The aim of this new approach is to lead to a constant frequency and low THD in grid current with a unit power factor and a minimum voltage variation despite the wind variation. To highlight the effectiveness of the proposed method, a comparison was made with classical DTC and field oriented control method (FOC). The obtained simulation results, with a variable wind profile, show an adequate dynamic of the conversion system using the proposed method compared to the classical approaches. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Tap Arduino: An Arduino microcontroller for low-latency auditory feedback in sensorimotor synchronization experiments.

PubMed

Schultz, Benjamin G; van Vugt, Floris T

2016-12-01

Timing abilities are often measured by having participants tap their finger along with a metronome and presenting tap-triggered auditory feedback. These experiments predominantly use electronic percussion pads combined with software (e.g., FTAP or Max/MSP) that records responses and delivers auditory feedback. However, these setups involve unknown latencies between tap onset and auditory feedback and can sometimes miss responses or record multiple, superfluous responses for a single tap. These issues may distort measurements of tapping performance or affect the performance of the individual. We present an alternative setup using an Arduino microcontroller that addresses these issues and delivers low-latency auditory feedback. We validated our setup by having participants (N = 6) tap on a force-sensitive resistor pad connected to the Arduino and on an electronic percussion pad with various levels of force and tempi. The Arduino delivered auditory feedback through a pulse-width modulation (PWM) pin connected to a headphone jack or a wave shield component. The Arduino's PWM (M = 0.6 ms, SD = 0.3) and wave shield (M = 2.6 ms, SD = 0.3) demonstrated significantly lower auditory feedback latencies than the percussion pad (M = 9.1 ms, SD = 2.0), FTAP (M = 14.6 ms, SD = 2.8), and Max/MSP (M = 15.8 ms, SD = 3.4). The PWM and wave shield latencies were also significantly less variable than those from FTAP and Max/MSP. The Arduino missed significantly fewer taps, and recorded fewer superfluous responses, than the percussion pad. The Arduino captured all responses, whereas at lower tapping forces, the percussion pad missed more taps. Regardless of tapping force, the Arduino outperformed the percussion pad. Overall, the Arduino is a high-precision, low-latency, portable, and affordable tool for auditory experiments.

Validity of semi-quantitative scale for brain MRI in unilateral cerebral palsy due to periventricular white matter lesions: Relationship with hand sensorimotor function and structural connectivity.

PubMed

Fiori, Simona; Guzzetta, Andrea; Pannek, Kerstin; Ware, Robert S; Rossi, Giuseppe; Klingels, Katrijn; Feys, Hilde; Coulthard, Alan; Cioni, Giovanni; Rose, Stephen; Boyd, Roslyn N

2015-01-01

To provide first evidence of construct validity of a semi-quantitative scale for brain structural MRI (sqMRI scale) in children with unilateral cerebral palsy (UCP) secondary to periventricular white matter (PWM) lesions, by examining the relationship with hand sensorimotor function and whole brain structural connectivity. Cross-sectional study of 50 children with UCP due to PWM lesions using 3 T (MRI), diffusion MRI and assessment of hand sensorimotor function. We explored the relationship of lobar, hemispheric and global scores on the sqMRI scale, with fractional anisotropy (FA), as a measure of brain white matter microstructure, and with hand sensorimotor measures (Assisting Hand Assessment, AHA; Jebsen-Taylor Test for Hand Function, JTTHF; Melbourne Assessment of Unilateral Upper Limb Function, MUUL; stereognosis; 2-point discrimination). Lobar and hemispheric scores on the sqMRI scale contralateral to the clinical side of hemiplegia correlated with sensorimotor paretic hand function measures and FA of a number of brain structural connections, including connections of brain areas involved in motor control (postcentral, precentral and paracentral gyri in the parietal lobe). More severe lesions correlated with lower sensorimotor performance, with the posterior limb of internal capsule score being the strongest contributor to impaired hand function. The sqMRI scale demonstrates first evidence of construct validity against impaired motor and sensory function measures and brain structural connectivity in a cohort of children with UCP due to PWM lesions. More severe lesions correlated with poorer paretic hand sensorimotor function and impaired structural connectivity in the hemisphere contralateral to the clinical side of hemiplegia. The quantitative structural MRI scoring may be a useful clinical tool for studying brain structure-function relationships but requires further validation in other populations of CP.

Quantitative comparison of cortical and deep grey matter in pathological subtypes of unilateral cerebral palsy.

PubMed

Scheck, Simon M; Pannek, Kerstin; Fiori, Simona; Boyd, Roslyn N; Rose, Stephen E

2014-10-01

The aim of this study was to quantify grey matter changes in children with unilateral cerebral palsy (UCP), differentiating between cortical or deep grey matter (CDGM) lesions, periventricular white matter (PWM) lesions, and unilateral and bilateral lesions. In a cross-sectional study we obtained high resolution structural magnetic resonance images from 72 children (41 males, 31 females, mean age 10y 9mo [SD 3y 1mo], range 5y 1mo-17y 1mo) with UCP (33 left, 39 right hemiplegia; Manual Ability Classification System level I n=29, II n=43; Gross Motor Function Classification System level I n=46, II n=26), and 19 children with typical development (CTD; eight males, 11 females, mean age 11y 2mo [SD 2y 7mo], range 7y 8mo-16y 4mo). Images were classified by lesion type and analyzed using voxel-based morphometry (VBM) and subcortical volumetric analysis. Deep grey matter volumes were not significantly different between children with CDGM and PWM lesions, with the thalamus, putamen, and globus pallidus being reduced unilaterally in both groups compared with CTD (p≤0.001). Children with CDGM lesions additionally showed widespread cortical changes involving all lobes using VBM (p<0.01). Children with bilateral lesions had reduced thalamus and putamen volumes bilaterally (p<0.001). The thalamic volume was reduced bilaterally in children with unilateral lesions (p=0.004). Lesions to the PWM cause secondary changes to the deep grey matter structures similar to primary changes seen in CDGM lesions. Despite having a unilateral phenotype, grey matter changes are observed bilaterally, even in children with unilateral lesions. © 2014 Mac Keith Press.

EMQIT: a machine learning approach for energy based PWM matrix quality improvement.

PubMed

Smolinska, Karolina; Pacholczyk, Marcin

2017-08-01

Transcription factor binding affinities to DNA play a key role for the gene regulation. Learning the specificity of the mechanisms of binding TFs to DNA is important both to experimentalists and theoreticians. With the development of high-throughput methods such as, e.g., ChiP-seq the need to provide unbiased models of binding events has been made apparent. We present EMQIT a modification to the approach introduced by Alamanova et al. and later implemented as 3DTF server. We observed that tuning of Boltzmann factor weights, used for conversion of calculated energies to nucleotide probabilities, has a significant impact on the quality of the associated PWM matrix. Consequently, we proposed to use receiver operator characteristics curves and the 10-fold cross-validation to learn best weights using experimentally verified data from TRANSFAC database. We applied our method to data available for various TFs. We verified the efficiency of detecting TF binding sites by the 3DTF matrices improved with our technique using experimental data from the TRANSFAC database. The comparison showed a significant similarity and comparable performance between the improved and the experimental matrices (TRANSFAC). Improved 3DTF matrices achieved significantly higher AUC values than the original 3DTF matrices (at least by 0.1) and, at the same time, detected notably more experimentally verified TFBSs. The resulting new improved PWM matrices for analyzed factors show similarity to TRANSFAC matrices. Matrices had comparable predictive capabilities. Moreover, improved PWMs achieve better results than matrices downloaded from 3DTF server. Presented approach is general and applicable to any energy-based matrices. EMQIT is available online at http://biosolvers.polsl.pl:3838/emqit . This article was reviewed by Oliviero Carugo, Marek Kimmel and István Simon.

Hardware realization of an SVM algorithm implemented in FPGAs

NASA Astrophysics Data System (ADS)

Wiśniewski, Remigiusz; Bazydło, Grzegorz; Szcześniak, Paweł

2017-08-01

The paper proposes a technique of hardware realization of a space vector modulation (SVM) of state function switching in matrix converter (MC), oriented on the implementation in a single field programmable gate array (FPGA). In MC the SVM method is based on the instantaneous space-vector representation of input currents and output voltages. The traditional computation algorithms usually involve digital signal processors (DSPs) which consumes the large number of power transistors (18 transistors and 18 independent PWM outputs) and "non-standard positions of control pulses" during the switching sequence. Recently, hardware implementations become popular since computed operations may be executed much faster and efficient due to nature of the digital devices (especially concurrency). In the paper, we propose a hardware algorithm of SVM computation. In opposite to the existing techniques, the presented solution applies COordinate Rotation DIgital Computer (CORDIC) method to solve the trigonometric operations. Furthermore, adequate arithmetic modules (that is, sub-devices) used for intermediate calculations, such as code converters or proper sectors selectors (for output voltages and input current) are presented in detail. The proposed technique has been implemented as a design described with the use of Verilog hardware description language. The preliminary results of logic implementation oriented on the Xilinx FPGA (particularly, low-cost device from Artix-7 family from Xilinx was used) are also presented.

Development of variable-rate sprayer for nursery liner applications

USDA-ARS?s Scientific Manuscript database

Sensor-guided application technologies are needed to achieve constant spray deposition for the rapid growth of nursery liner trees during a growing season. An experimental real-time variable-rate sprayer that implemented 20 Hz ultrasonic sensors and pulse width modulation (PWM) solenoid valve-contro...

A new type of accelerator power supply based on voltage-type space vector PWM rectification technology

NASA Astrophysics Data System (ADS)

Wu, Fengjun; Gao, Daqing; Shi, Chunfeng; Huang, Yuzhen; Cui, Yuan; Yan, Hongbin; Zhang, Huajian; Wang, Bin; Li, Xiaohui

2016-08-01

To solve the problems such as low input power factor, a large number of AC current harmonics and instable DC bus voltage due to the diode or thyristor rectifier used in an accelerator power supply, particularly in the Heavy Ion Research Facility in Lanzhou-Cooler Storage Ring (HIRFL-CSR), we designed and built up a new type of accelerator power supply prototype base on voltage-type space vector PWM (SVPWM) rectification technology. All the control strategies are developed in TMS320C28346, which is a digital signal processor from TI. The experimental results indicate that an accelerator power supply with a SVPWM rectifier can solve the problems above well, and the output performance such as stability, tracking error and ripple current meet the requirements of the design. The achievement of prototype confirms that applying voltage-type SVPWM rectification technology in an accelerator power supply is feasible; and it provides a good reference for design and build of this new type of power supply.

Multiphase power supply when inverting currents for group of Peltier elements

NASA Astrophysics Data System (ADS)

Osintsev, A. V.; Sobko, A. A.; Komnatnov, M. E.

2018-05-01

The use of multiphase power supply of a group of Peltier elements (PE) is considered to reduce the load on the power source. Schemes and a control layout with the use of the H-bridge, allowing the invert of the current through the PE, are given. The analysis of the operation of the used H-bridges and PE in the frequency range of the control PWM signal from 30 Hz to 32 kHz is performed. The algorithm for monitoring the current sensors is presented and the time diagrams of the currents are represented through the PE and H-bridges using a two-phase and four-phase control PWM signal for one, two and four phases of the supply. The results showed stable heating and cooling of the PE at frequencies from 30 Hz to 1 kHz. The use of multiphase power supply of PE made it possible to significantly reduce the load on the power source.

Power control electronics for cryogenic instrumentation

NASA Technical Reports Server (NTRS)

Ray, Biswajit; Gerber, Scott S.; Patterson, Richard L.; Myers, Ira T.

1995-01-01

In order to achieve a high-efficiency high-density cryogenic instrumentation system, the power processing electronics should be placed in the cold environment along with the sensors and signal-processing electronics. The typical instrumentation system requires low voltage dc usually obtained from processing line frequency ac power. Switch-mode power conversion topologies such as forward, flyback, push-pull, and half-bridge are used for high-efficiency power processing using pulse-width modulation (PWM) or resonant control. This paper presents several PWM and multiresonant power control circuits, implemented using commercially available CMOS and BiCMOS integrated circuits, and their performance at liquid-nitrogen temperature (77 K) as compared to their room temperature (300 K) performance. The operation of integrated circuits at cryogenic temperatures results in an improved performance in terms of increased speed, reduced latch-up susceptibility, reduced leakage current, and reduced thermal noise. However, the switching noise increased at 77 K compared to 300 K. The power control circuits tested in the laboratory did successfully restart at 77 K.

A Simple Accelerometer Calibrator

NASA Astrophysics Data System (ADS)

Salam, R. A.; Islamy, M. R. F.; Munir, M. M.; Latief, H.; Irsyam, M.; Khairurrijal

2016-08-01

High possibility of earthquake could lead to the high number of victims caused by it. It also can cause other hazards such as tsunami, landslide, etc. In that case it requires a system that can examine the earthquake occurrence. Some possible system to detect earthquake is by creating a vibration sensor system using accelerometer. However, the output of the system is usually put in the form of acceleration data. Therefore, a calibrator system for accelerometer to sense the vibration is needed. In this study, a simple accelerometer calibrator has been developed using 12 V DC motor, optocoupler, Liquid Crystal Display (LCD) and AVR 328 microcontroller as controller system. The system uses the Pulse Wave Modulation (PWM) form microcontroller to control the motor rotational speed as response to vibration frequency. The frequency of vibration was read by optocoupler and then those data was used as feedback to the system. The results show that the systems could control the rotational speed and the vibration frequencies in accordance with the defined PWM.

Rethinking programme evaluation in health professions education: beyond 'did it work?'.

PubMed

Haji, Faizal; Morin, Marie-Paule; Parker, Kathryn

2013-04-01

For nearly 40 years, outcome-based models have dominated programme evaluation in health professions education. However, there is increasing recognition that these models cannot address the complexities of the health professions context and studies employing alternative evaluation approaches that are appearing in the literature. A similar paradigm shift occurred over 50 years ago in the broader discipline of programme evaluation. Understanding the development of contemporary paradigms within this field provides important insights to support the evolution of programme evaluation in the health professions. In this discussion paper, we review the historical roots of programme evaluation as a discipline, demonstrating parallels with the dominant approach to evaluation in the health professions. In tracing the evolution of contemporary paradigms within this field, we demonstrate how their aim is not only to judge a programme's merit or worth, but also to generate information for curriculum designers seeking to adapt programmes to evolving contexts, and researchers seeking to generate knowledge to inform the work of others. From this evolution, we distil seven essential elements of educational programmes that should be evaluated to achieve the stated goals. Our formulation is not a prescriptive method for conducting programme evaluation; rather, we use these elements as a guide for the development of a holistic 'programme of evaluation' that involves multiple stakeholders, uses a combination of available models and methods, and occurs throughout the life of a programme. Thus, these elements provide a roadmap for the programme evaluation process, which allows evaluators to move beyond asking whether a programme worked, to establishing how it worked, why it worked and what else happened. By engaging in this process, evaluators will generate a sound understanding of the relationships among programmes, the contexts in which they operate, and the outcomes that result from them. © Blackwell Publishing Ltd 2013.

Synthesizing genetic sequential logic circuit with clock pulse generator.

PubMed

Chuang, Chia-Hua; Lin, Chun-Liang

2014-05-28

Rhythmic clock widely occurs in biological systems which controls several aspects of cell physiology. For the different cell types, it is supplied with various rhythmic frequencies. How to synthesize a specific clock signal is a preliminary but a necessary step to further development of a biological computer in the future. This paper presents a genetic sequential logic circuit with a clock pulse generator based on a synthesized genetic oscillator, which generates a consecutive clock signal whose frequency is an inverse integer multiple to that of the genetic oscillator. An analogous electronic waveform-shaping circuit is constructed by a series of genetic buffers to shape logic high/low levels of an oscillation input in a basic sinusoidal cycle and generate a pulse-width-modulated (PWM) output with various duty cycles. By controlling the threshold level of the genetic buffer, a genetic clock pulse signal with its frequency consistent to the genetic oscillator is synthesized. A synchronous genetic counter circuit based on the topology of the digital sequential logic circuit is triggered by the clock pulse to synthesize the clock signal with an inverse multiple frequency to the genetic oscillator. The function acts like a frequency divider in electronic circuits which plays a key role in the sequential logic circuit with specific operational frequency. A cascaded genetic logic circuit generating clock pulse signals is proposed. Based on analogous implement of digital sequential logic circuits, genetic sequential logic circuits can be constructed by the proposed approach to generate various clock signals from an oscillation signal.

Powder Flux Regulation in the Laser Material Deposition Process

NASA Astrophysics Data System (ADS)

Arrizubieta, Jon Iñaki; Wegener, Maximiliam; Arntz, Kristian; Lamikiz, Aitzol; Ruiz, Jose Exequiel

In the present research work a powder flux regulation system has been designed, developed and validated with the aim of improving the Laser Material Deposition (LMD) process. In this process, the amount of deposited material per substrate surface unit area depends on the real feed rate of the nozzle. Therefore, a regulation system based on a solenoid valve has been installed at the nozzle entrance in order to control the powder flux. The powder flux control has been performed based on the machine real feed rate, which is compared with the programmed feed rate. An instantaneous velocity error is calculated and the powder flow is controlled as a function of this variation using Pulse Width Modulation (PWM) signals. Thereby, in zones where the Laser Material Deposition machine reduces the feed rate due to a trajectory change, powder accumulation can be avoided and the generated clads would present a homogeneous shape.

An electronic flow control system for a variable-rate tree sprayer

USDA-ARS?s Scientific Manuscript database

Precise modulation of nozzle flow rates is a critical measure to achieve variable-rate spray applications. An electronic flow rate control system accommodating with microprocessors and pulse width modulation (PWM) controlled solenoid valves was designed to manipulate the output of spray nozzles inde...

Development of digital flow control system for multi-channel variable-rate sprayers

USDA-ARS?s Scientific Manuscript database

Precision modulation of nozzle flow rates is a critical step for variable-rate spray applications in orchards and ornamental nurseries. An automatic flow rate control system activated with microprocessors and pulse width modulation (PWM) controlled solenoid valves was developed to control flow rates...

Effect of monoclonal antibodies (MoAb) to class I and class II HLA antigens on lectin- and MoAb OKT3-induced lymphocyte proliferation.

PubMed

Akiyama, Y; Zicht, R; Ferrone, S; Bonnard, G D; Herberman, R B

1985-04-01

We have examined the effect of several monoclonal antibodies (MoAb) to monomorphic determinants of class II HLA antigens, and MoAb to monomorphic determinants of class I HLA antigens and to beta-2-microglobulin (beta 2-mu) on lectin- and MoAb OKT3-induced proliferation of human peripheral blood mononuclear cells (PBMNC) and cultured T cells (CTC). Some, but not all, anti-class II HLA MoAb inhibited the proliferative response of PBMNC to MoAb OKT3 and pokeweed mitogen (PWM). The degree of inhibitory effect varied considerably. This effect was not limited to anti-class II HLA MoAb since anti-class I HLA MoAb and anti-beta 2-mu MoAb also inhibited MoAb OKT3- or PWM-induced proliferative responses. In contrast, the response of PBMNC to phytohemagglutinin (PHA) and concanavalin A (Con A) was not blocked by any anti-class II HLA MoAb. However, some anti-class II HLA MoAb also inhibited the proliferative response of CTC plus allogeneic peripheral blood adherent accessory cells (AC) to PHA or Con A as well as to MoAb OKT3 or PWM. This may be attributable to the substantially greater class II HLA antigen expression by CTC than by fresh lymphocytes. Pretreatment of either CTC or AC with anti-class II HLA MoAb inhibited OKT3-induced proliferation. In contrast, pretreatment of CTC, but not AC, with anti-class I HLA MoAb inhibited the proliferative response of CTC to OKT3. Pretreatment of CTC with anti-class I HLA MoAb inhibited PHA-, Con A and PWM-induced proliferation, to a greater degree than the anti-class II HLA MoAb. It appears as if lymphocyte activation by different mitogens exhibits variable requirements for the presence of cells expressing major histocompatibility determinants. Binding of Ab to membrane markers may interfere with lymphocyte-AC cooperation, perhaps by inhibiting binding of mitogens to their receptors or by interfering with lymphocyte and AC function. We also have examined the role of class II HLA antigens on CTC by depleting class II HLA-positive cells. As expected, elimination of class II HLA-positive AC with anti-class II HLA MoAb plus complement caused a decrease in proliferation of CTC in response to all the mitogens tested. In contrast, elimination of class II HLA-positive CTC was shown to clearly increase proliferation of CTC, perhaps because this may deplete class II HLA-positive suppressor cells.

Longitudinal Effects of a Two-Generation Preschool Programme on Receptive Language Skill in Low-Income Canadian Children to Age 10 Years

ERIC Educational Resources Information Center

Mughal, Muhammad Kashif; Ginn, Carla S.; Perry, Robert L.; Benzies, Karen M.

2016-01-01

We explored longitudinal effects of a two-generation preschool programme on receptive language scores in children (n = 78) at age 10 years, living with low income. Scores at four time-points, programme intake, exit, age 7, and age 10 years were measured using the "Peabody picture vocabulary test" (3rd ed.). Effects of culture…

High efficiency H6 single-phase transformerless grid-tied PV inverter with proposed modulation for reactive power generation

NASA Astrophysics Data System (ADS)

Almasoudi, Fahad M.; Alatawi, Khaled S.; Matin, Mohammad

2017-08-01

Implementation of transformerless inverters in PV grid-tied system offer great benefits such as high efficiency, light weight, low cost, etc. Most of the proposed transformerless inverters in literature are verified for only real power application. Currently, international standards such as VDE-AR-N 4105 has demanded that PV grid-tied inverters should have the ability of controlling a specific amount of reactive power. Generation of reactive power cannot be accomplished in single phase transformerless inverter topologies because the existing modulation techniques are not adopted for a freewheeling path in the negative power region. This paper enhances a previous high efficiency proposed H6 trnasformerless inverter with SiC MOSFETs and demonstrates new operating modes for the generation of reactive power. A proposed pulse width modulation (PWM) technique is applied to achieve bidirectional current flow through freewheeling state. A comparison of the proposed H6 transformerless inverter using SiC MOSFETs and Si MOSFTEs is presented in terms of power losses and efficiency. The results show that reactive power control is attained without adding any additional active devices or modification to the inverter structure. Also, the proposed modulation maintains a constant common mode voltage (CM) during every operating mode and has low leakage current. The performance of the proposed system verifies its effectiveness in the next generation PV system.

Analysis of disconnected diallel mating designs II: results from a third generation progeny test of the New Zealand radiata pine improvement programme.

Treesearch

J.N. King; M.J. Carson; G.R. Johnson

1998-01-01

Genetic parameters from a second generation (F2) disconnected diallel progeny test of the New Zealand radiata pine improvement programme are presented. Heritability estimates of growth and yield traits of 0.2 are similar to progeny test results of the previous generation (F1) generation tests. A trend of declining dominance...

Neural Correlates of Sublexical Processing in Phonological Working Memory

ERIC Educational Resources Information Center

McGettigan, Carolyn; Warren, Jane E.; Eisner, Frank; Marshall, Chloe R.; Shanmugalingam, Pradheep; Scott, Sophie K.

2011-01-01

This study investigated links between working memory and speech processing systems. We used delayed pseudoword repetition in fMRI to investigate the neural correlates of sublexical structure in phonological working memory (pWM). We orthogonally varied the number of syllables and consonant clusters in auditory pseudowords and measured the neural…

[Invert transformer design for high frequency X-ray machine based on PWM controller SG 3525].

PubMed

Yu, Xue-fei; Li, Zhe

2005-07-01

This paper introduces the principle of invert transformer of high frequency X-ray machine, and analyzes its main constitution. Meanwhile, a scheme based on SG3525 for closed loop voltage regulation is given. The experimental result testifies its efficiency and utility.

Spray outputs from a variable-rate sprayer manipulated with PWM solenoid valves

USDA-ARS?s Scientific Manuscript database

Pressure fluctuations during variable-rate spray applications can affect nozzle flow rate fluctuations, resulting in spray outputs that do not coincide with the prescribed canopy structure volume. Variations in total flow rate discharged from 40 nozzles, each coupled with a pulse-width-modulated (PW...

Second-generation HIV surveillance: better data for decision-making.

PubMed Central

Rehle, Thomas; Lazzari, Stefano; Dallabetta, Gina; Asamoah-Odei, Emil

2004-01-01

This paper seeks to outline the key elements of the expanded surveillance efforts recommended by the second-generation HIV surveillance approach. Second-generation systems focus on improving and expanding existing surveillance methods and combine them in ways that have the greatest explanatory power. The main elements of this approach include: considering biological surveillance - HIV, AIDS, sexually transmitted infections (STIs) - and behavioural surveillance as integral components, targeting surveillance efforts at segments of the population where most new infections are concentrated - which might differ depending on the stage and type of the epidemic - and providing the rationale for the optimal use of data generated for monitoring the HIV epidemic and evaluating national AIDS control programmes. The paper emphasizes improvements in existing surveillance methodologies and discusses in detail crucial issues such as the validity of HIV prevalence data measured in pregnant women and linking HIV surveillance and behavioural data collection. In addition, a strategic partnership between second-generation surveillance and AIDS programme evaluation is proposed that stresses the complementary roles of these data collection activities in determining the effectiveness of prevention and care programmes and explaining the epidemiological trend data collected by sentinel serosurveillance systems. In conclusion, second-generation HIV surveillance systems provide a comprehensive, cost-effective and appropriate response to the information needs of AIDS control programmes. The implementation of such systems, including a better use of the data generated by the system, will ensure that national programmes are in the best possible position to respond to the challenges of the epidemic. PMID:15042234

Second-generation HIV surveillance: better data for decision-making.

PubMed

Rehle, Thomas; Lazzari, Stefano; Dallabetta, Gina; Asamoah-Odei, Emil

2004-02-01

This paper seeks to outline the key elements of the expanded surveillance efforts recommended by the second-generation HIV surveillance approach. Second-generation systems focus on improving and expanding existing surveillance methods and combine them in ways that have the greatest explanatory power. The main elements of this approach include: considering biological surveillance - HIV, AIDS, sexually transmitted infections (STIs) - and behavioural surveillance as integral components, targeting surveillance efforts at segments of the population where most new infections are concentrated - which might differ depending on the stage and type of the epidemic - and providing the rationale for the optimal use of data generated for monitoring the HIV epidemic and evaluating national AIDS control programmes. The paper emphasizes improvements in existing surveillance methodologies and discusses in detail crucial issues such as the validity of HIV prevalence data measured in pregnant women and linking HIV surveillance and behavioural data collection. In addition, a strategic partnership between second-generation surveillance and AIDS programme evaluation is proposed that stresses the complementary roles of these data collection activities in determining the effectiveness of prevention and care programmes and explaining the epidemiological trend data collected by sentinel serosurveillance systems. In conclusion, second-generation HIV surveillance systems provide a comprehensive, cost-effective and appropriate response to the information needs of AIDS control programmes. The implementation of such systems, including a better use of the data generated by the system, will ensure that national programmes are in the best possible position to respond to the challenges of the epidemic.

Sustainable Schools Programmes: What Influence on Schools and How Do We Know?

ERIC Educational Resources Information Center

Rickinson, Mark; Hall, Matthew; Reid, Alan

2016-01-01

This paper focuses on our experience of researching the influence of ResourceSmart Schools, a sustainable schools programme in Victoria, Australia. Drawing on ideas from programme theory and realist synthesis, we illustrate and reflect upon our approach to conceptualising, investigating and generating evidence about the programme's…

An Experimental Testbed for a Free-Floating Manipulator

DTIC Science & Technology

1993-12-01

brushless servo amplifiers are four quadrant , 20 kHz PWM amplifiers that provide economical control of brushless motors rated from 1/3 to 2 Hp shaft Watts...backplanes that came out of the Versa-Module- Europa consortium [Ref. 15]. The VME is a bus that acts as the path and translator of information between

An Approach to Average Modeling and Simulation of Switch-Mode Systems

ERIC Educational Resources Information Center

Abramovitz, A.

2011-01-01

This paper suggests a pedagogical approach to teaching the subject of average modeling of PWM switch-mode power electronics systems through simulation by general-purpose electronic circuit simulators. The paper discusses the derivation of PSPICE/ORCAD-compatible average models of the switch-mode power stages, their software implementation, and…

Evidence for the Decreasing Impact of Cognitive Ability on Second Language Development as Proficiency Increases

ERIC Educational Resources Information Center

Serafini, Ellen J.; Sanz, Cristina

2016-01-01

This study investigated whether the role of working memory capacity varies over the course of second language (L2) morphosyntactic development. Eighty-seven beginning, intermediate, and advanced university L2 Spanish learners completed two nonverbal tasks measuring executive function (EF) and phonological working memory (PWM) in their native…

Effects of mineral and vitamin supplementation to pasteurized whole milk diets on growth and health of preruminant Holstein bull calves

USDA-ARS?s Scientific Manuscript database

Our objective was to determine whether supplementation of vitamins and trace minerals (VTM), formulated to meet or exceed NRC requirements when added to pasteurized whole milk (PWM), increases challenge resolution and prevents intestinal macromolecular permeability after injection with bacterial lip...

Assessing the Utility of the Willingness/Prototype Model in Predicting Help-Seeking Decisions

ERIC Educational Resources Information Center

Hammer, Joseph H.; Vogel, David L.

2013-01-01

Prior research on professional psychological help-seeking behavior has operated on the assumption that the decision to seek help is based on intentional and reasoned processes. However, research on the dual-process prototype/willingness model (PWM; Gerrard, Gibbons, Houlihan, Stock, & Pomery, 2008) suggests health-related decisions may also…

Magnetic resonance spectroscopy in mild cognitive impairment: systematic review and meta-analysis.

PubMed

Tumati, Shankar; Martens, Sander; Aleman, André

2013-12-01

Research using proton magnetic resonance spectroscopy (MRS) can potentially elucidate metabolite changes representing early degeneration in Mild Cognitive Impairment (MCI), an early stage of dementia. We integrated the published literature using meta-analysis to identify patterns of metabolite changes in MCI. 29 MRS studies (with a total of 607 MCI patients and 862 healthy controls) were classified according to brain regions. Hedges' g was used as effect size in a random effects model. N-Acetyl Aspartate (NAA) measures were consistently reduced in posterior cingulate (PC), hippocampus, and the paratrigonal white matter (PWM). Creatine (Cr) concentration was reduced in the hippocampus and PWM. Choline (Cho) concentration was reduced in the hippocampus while Cho/Cr ratio was raised in the PC. Myo-inositol (mI) concentration was raised in the PC and mI/Cr ratio was raised in the hippocampus. NAA/mI ratio was reduced in the PC. NAA may be the most reliable marker of brain dysfunction in MCI though mI, Cho, and Cr may also contribute towards this. Copyright © 2013 Elsevier Ltd. All rights reserved.

Simulation of an Electromechanical Spin Motor System of a Control Moment Gyroscope

NASA Technical Reports Server (NTRS)

Inampudi, Ravi; Gordeuk, John

2016-01-01

A two-phase brushless DC motor (BDCM) with pulse-width modulated (PWM) voltage drive is simulated to control the flywheel speed of a control moment gyroscope (CMG). An overview of a double-gimballed control moment gyroscope (DGCMG) assembly is presented along with the CMG torque effects on the spacecraft. The operating principles of a two-phase brushless DC motor are presented and the system's electro-mechanical equations of motion are developed for the root-mean-square (RMS) currents and wheel speed. It is shown that the system is an extremely "stiff" set of first-order equations for which an implicit Euler integrator is required for a stable solution. An adaptive proportional voltage controller is presented which adjusts the PWM voltages depending on several control modes for speed, current, and torque. The simulation results illustrate the interaction between the electrical system and the load dynamics and how these influence the overall performance of the system. As will be shown, the CMG spin motor model can directly provide electrical power use and thermal power output to spacecraft subsystems for effective (average) calculations of CMG power consumption.

An improved immune algorithm for optimizing the pulse width modulation control sequence of inverters

NASA Astrophysics Data System (ADS)

Sheng, L.; Qian, S. Q.; Ye, Y. Q.; Wu, Y. H.

2017-09-01

In this article, an improved immune algorithm (IIA), based on the fundamental principles of the biological immune system, is proposed for optimizing the pulse width modulation (PWM) control sequence of a single-phase full-bridge inverter. The IIA takes advantage of the receptor editing and adaptive mutation mechanisms of the immune system to develop two operations that enhance the population diversity and convergence of the proposed algorithm. To verify the effectiveness and examine the performance of the IIA, 17 cases are considered, including fixed and disturbed resistances. Simulation results show that the IIA is able to obtain an effective PWM control sequence. Furthermore, when compared with existing immune algorithms (IAs), genetic algorithms (GAs), a non-traditional GA, simplified simulated annealing, and a generalized Hopfield neural network method, the IIA can achieve small total harmonic distortion (THD) and large magnitude. Meanwhile, a non-parametric test indicates that the IIA is significantly better than most comparison algorithms. Supplemental data for this article can be accessed at http://dx.doi.org/10.1080/0305215X.2016.1250894.

Assessing the utility of the willingness/prototype model in predicting help-seeking decisions.

PubMed

Hammer, Joseph H; Vogel, David L

2013-01-01

Prior research on professional psychological help-seeking behavior has operated on the assumption that the decision to seek help is based on intentional and reasoned processes. However, research on the dual-process prototype/willingness model (PWM; Gerrard, Gibbons, Houlihan, Stock, & Pomery, 2008) suggests health-related decisions may also involve social reaction processes that influence one's spontaneous willingness (rather than planned intention) to seek help, given conducive circumstances. The present study used structural equation modeling to evaluate the ability of these 2 information-processing pathways (i.e., the reasoned pathway and the social reaction pathway) to predict help-seeking decisions among 182 college students currently experiencing clinical levels of psychological distress. Results indicated that when both pathways were modeled simultaneously, only the social reaction pathway independently accounted for significant variance in help-seeking decisions. These findings argue for the utility of the PWM framework in the context of professional psychological help seeking and hold implications for future counseling psychology research, prevention, and practice. PsycINFO Database Record (c) 2013 APA, all rights reserved.

PWM-switching pattern-based diagnosis scheme for single and multiple open-switch damages in VSI-fed induction motor drives.

PubMed

Trabelsi, Mohamed; Boussak, Mohamed; Gossa, Moncef

2012-03-01

This paper deals with a fault detection technique for insulated-gate bipolar transistors (IGBTs) open-circuit faults in voltage source inverter (VSI)-fed induction motor drives. The novelty of this idea consists in analyzing the pulse-width modulation (PWM) switching signals and the line-to-line voltage levels during the switching times, under both healthy and faulty operating conditions. The proposed method requires line-to-line voltage measurement, which provides information about switching states and is not affected by the load. The fault diagnosis scheme is achieved using simple hardware and can be included in the existing inverter system without any difficulty. In addition, it allows not only accurate single and multiple faults diagnosis but also minimization of the fault detection time to a maximum of one switching period (T(c)). Simulated and experimental results on a 3-kW squirrel-cage induction motor drive are displayed to validate the feasibility and the effectiveness of the proposed strategy. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

An Energy Saving Green Plug Device for Nonlinear Loads

NASA Astrophysics Data System (ADS)

Bloul, Albe; Sharaf, Adel; El-Hawary, Mohamed

2018-03-01

The paper presents a low cost a FACTS Based flexible fuzzy logic based modulated/switched tuned arm filter and Green Plug compensation (SFC-GP) scheme for single-phase nonlinear loads ensuring both voltage stabilization and efficient energy utilization. The new Green Plug-Switched filter compensator SFC modulated LC-Filter PWM Switched Capacitive Compensation Devices is controlled using a fuzzy logic regulator to enhance power quality, improve power factor at the source and reduce switching transients and inrush current conditions as well harmonic contents in source current. The FACTS based SFC-GP Device is a member of family of Green Plug/Filters/Compensation Schemes used for efficient energy utilization, power quality enhancement and voltage/inrush current/soft starting control using a dynamic error driven fuzzy logic controller (FLC). The device with fuzzy logic controller is validated using the Matlab / Simulink Software Environment for enhanced power quality (PQ), improved power factor and reduced inrush currents. This is achieved using modulated PWM Switching of the Filter-Capacitive compensation scheme to cope with dynamic type nonlinear and inrush cyclical loads..

Permanent magnet DC motor control by using arduino and motor drive module BTS7960

NASA Astrophysics Data System (ADS)

Syukriyadin, S.; Syahrizal, S.; Mansur, G.; Ramadhan, H. P.

2018-05-01

This study proposes a control system for permanent magnet DC (PMDC) motor. PMDC drive control system has two critical parameters: control and monitoring. Control system includes rotation speed control and direction of rotation of motor using motor drive module BTS7960. The PWM signal has a fixed frequency of waves with varying duty cycles (between 0% and 100%), so the motor rotation can be regulated gradually using a potentiometer already programmed on the Arduino Uno board. The motor rotation direction setting uses the H-bridge circuit method using a 3-way switch to set the direction of forward-reverse rotation of the motor. The monitoring system includes measurements of rotational speed, current, and voltage. Motor rotation speed can be adjusted from the armature voltage settings through the duty cycle PWM setting so that the motor speed can be increased or decreased by the desired duty cycle. From the unload PMDC motor test results it has also been shown that the torque of the motor is relatively constant when there is a change in speed from low rpm to high rpm or vice versa.

Synthesizing genetic sequential logic circuit with clock pulse generator

PubMed Central

2014-01-01

Background Rhythmic clock widely occurs in biological systems which controls several aspects of cell physiology. For the different cell types, it is supplied with various rhythmic frequencies. How to synthesize a specific clock signal is a preliminary but a necessary step to further development of a biological computer in the future. Results This paper presents a genetic sequential logic circuit with a clock pulse generator based on a synthesized genetic oscillator, which generates a consecutive clock signal whose frequency is an inverse integer multiple to that of the genetic oscillator. An analogous electronic waveform-shaping circuit is constructed by a series of genetic buffers to shape logic high/low levels of an oscillation input in a basic sinusoidal cycle and generate a pulse-width-modulated (PWM) output with various duty cycles. By controlling the threshold level of the genetic buffer, a genetic clock pulse signal with its frequency consistent to the genetic oscillator is synthesized. A synchronous genetic counter circuit based on the topology of the digital sequential logic circuit is triggered by the clock pulse to synthesize the clock signal with an inverse multiple frequency to the genetic oscillator. The function acts like a frequency divider in electronic circuits which plays a key role in the sequential logic circuit with specific operational frequency. Conclusions A cascaded genetic logic circuit generating clock pulse signals is proposed. Based on analogous implement of digital sequential logic circuits, genetic sequential logic circuits can be constructed by the proposed approach to generate various clock signals from an oscillation signal. PMID:24884665

High Speed and High Functional Inverter Power Supplies for Plasma Generation and Control, and their Performance

NASA Astrophysics Data System (ADS)

Uesugi, Yoshihiko; Razzak, Mohammad A.; Kondo, Kenji; Kikuchi, Yusuke; Takamura, Shuichi; Imai, Takahiro; Toyoda, Mitsuhiro

The Rapid development of high power and high speed semiconductor switching devices has led to their various applications in related plasma fields. Especially, a high speed inverter power supply can be used as an RF power source instead of conventional linear amplifiers and a power supply to control the magnetic field in a fusion plasma device. In this paper, RF thermal plasma production and plasma heating experiments are described emphasis placed on using a static induction transistor inverter at a frequency range between 200 kHz and 2.5 MHz as an RF power supply. Efficient thermal plasma production is achieved experimentally by using a flexible and easily operated high power semiconductor inverter power supply. Insulated gate bipolar transistor (IGBT) inverter power supplies driven by a high speed digital signal processor are applied as tokamak joule coil and vertical coil power supplies to control plasma current waveform and plasma equilibrium. Output characteristics, such as the arbitrary bipolar waveform generation of a pulse width modulation (PWM) inverter using digital signal processor (DSP) can be successfully applied to tokamak power supplies for flexible plasma current operation and fast position control of a small tokamak.

Aqueous exposure to Aroclor 1254 modulates the mitogenic response of Atlantic salmon anterior kidney T-cells: indications of short- and long-term immunomodulation.

PubMed

Iwanowicz, Luke R; Lerner, Darren T; Blazer, Vicki S; McCormick, Stephen D

2005-05-15

Polychlorinated biphenyls (PCBs) exist as persistent organic pollutants in numerous river systems in the United States. Unfortunately, some of these rivers are sites of active Atlantic salmon restoration programs, and polychlorinated biphenyls have been implicated as ancillary factors contributing to failed salmon restoration. Here, we investigate the immediate and chronic effects of intermediate duration aqueous PCB exposure (1 or 10 microgL-1 Aroclor 1254) on the mitogen-stimulated lymphoproliferative response of Atlantic salmon anterior kidney leukocytes (AKLs). A short-term study was designed to examine immunomodulation in Atlantic salmon smolts immediately following 21 days of aqueous exposure, while a long-term study evaluated chronic impacts in the mitogen response in parr 15 months post-exposure as larvae. The proliferative response of AKLs to the mitogens concanavalin A (CON A), phytohemaglutinnin-P (PHA-P), pokeweed mitogen (PWM), and lipopolysaccharide were used as an indice of immunomodulation. The proliferative response to the T-cell mitogens CON A and PHA-P was significantly increased in the 10 microgL-1 group (n=10; P=0.043 and 0.002, respectively) immediately following exposure of smolts. Additionally, The PHA-P response was significantly increased in the 1 microgL-1 exposure group (n=10, P=0.036). In fish treated as larvae and tested 15 months later, the PHA-P sensitive populations exhibited elevated proliferation in the 1 and 10 microgL-1 groups (n=12, P<0.04) relative to the vehicle control while the PWM response was significantly increased (n=12, P=0.036) only in the 10 microgL-1 treated groups. These results demonstrate an immunomodulatory effect of PCBs on T-cell mitogen sensitive populations of lymphocytes in Atlantic salmon as well as long-term immunomodulation in PHA-P and PWM sensitive populations.

Managing Complexity in Evidence Analysis: A Worked Example in Pediatric Weight Management.

PubMed

Parrott, James Scott; Henry, Beverly; Thompson, Kyle L; Ziegler, Jane; Handu, Deepa

2018-05-02

Nutrition interventions are often complex and multicomponent. Typical approaches to meta-analyses that focus on individual causal relationships to provide guideline recommendations are not sufficient to capture this complexity. The objective of this study is to describe the method of meta-analysis used for the Pediatric Weight Management (PWM) Guidelines update and provide a worked example that can be applied in other areas of dietetics practice. The effects of PWM interventions were examined for body mass index (BMI), body mass index z-score (BMIZ), and waist circumference at four different time periods. For intervention-level effects, intervention types were identified empirically using multiple correspondence analysis paired with cluster analysis. Pooled effects of identified types were examined using random effects meta-analysis models. Differences in effects among types were examined using meta-regression. Context-level effects are examined using qualitative comparative analysis. Three distinct types (or families) of PWM interventions were identified: medical nutrition, behavioral, and missing components. Medical nutrition and behavioral types showed statistically significant improvements in BMIZ across all time points. Results were less consistent for BMI and waist circumference, although four distinct patterns of weight status change were identified. These varied by intervention type as well as outcome measure. Meta-regression indicated statistically significant differences between the medical nutrition and behavioral types vs the missing component type for both BMIZ and BMI, although the pattern varied by time period and intervention type. Qualitative comparative analysis identified distinct configurations of context characteristics at each time point that were consistent with positive outcomes among the intervention types. Although analysis of individual causal relationships is invaluable, this approach is inadequate to capture the complexity of dietetics practice. An alternative approach that integrates intervention-level with context-level meta-analyses may provide deeper understanding in the development of practice guidelines. Copyright © 2018 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Feeding untreated and pasteurized waste milk and bulk milk to calves: effects on calf performance, health status and antibiotic resistance of faecal bacteria.

PubMed

Aust, V; Knappstein, K; Kunz, H-J; Kaspar, H; Wallmann, J; Kaske, M

2013-12-01

Non-saleable milk (waste milk, WM) is contaminated with an undefined spectrum of potentially harmful pathogens and antimicrobial residues. The objective of this study was to determine the impact of feeding bulk milk (BM) or WM - both pasteurized or not - on calf performance, health and the antibiotic resistance of specific faecal bacteria. A total of 114 calves from a large-scale dairy were housed outdoors in individual hutches and were randomly assigned to one of four feeding groups. The calves were fed either WM, pasteurized WM (pWM), BM or pasteurized BM (pBM) from day 3 to 56 of life. Milk samples taken from the pasteurizer and calves' nipple buckets were investigated at regular intervals for total plate count and counts of thermoduric bacteria, coliforms and mastitis pathogens. Faecal samples were taken on days 2, 14, 28 and 56 of life from randomly selected calves of the WM, pWM and BM groups (each N = 8-9) and processed to obtain from each sample preferably two isolates of Escherichia (E.) coli and Enterococcus spp. respectively. Isolates were tested for their antimicrobial susceptibility to 25 antimicrobial agents by broth microdilution. Daily weight gain, milk and calf starter intake and health parameters did not differ significantly between the calves of the four feeding groups. The proportion of resistant E. coli isolates was significantly higher in calves fed WM and in calves fed pWM (most pronounced for cephalosporins) than in calves receiving BM. No differences in resistance were found for Enterococus spp. Thus, the concerns for selecting resistant faecal bacteria by feeding WM seem to be justified. Nonetheless, pasteurized WM of cows not treated with antimicrobials represents an acceptable feed for young calves. © 2012 Blackwell Verlag GmbH.

Aqueous exposure to Aroclor 1254 modulates the mitogenic response of Atlantic salmon anterior kidney T-cells: Indications of short- and long-term immunomodulation

USGS Publications Warehouse

Iwanowicz, L.R.; Lerner, D.T.; Blazer, V.S.; McCormick, S.D.

2005-01-01

Polychlorinated biphenyls (PCBs) exist as persistent organic pollutants in numerous river systems in the United States. Unfortunately, some of these rivers are sites of active Atlantic salmon restoration programs, and polychlorinated biphenyls have been implicated as ancillary factors contributing to failed salmon restoration. Here, we investigate the immediate and chronic effects of intermediate duration aqueous PCB exposure (1 or 10 ??g L-1 Aroclor 1254) on the mitogen-stimulated lymphoproliferative response of Atlantic salmon anterior kidney leukocytes (AKLs). A short-term study was designed to examine immunomodulation in Atlantic salmon smolts immediately following 21 days of aqueous exposure, while a long-term study evaluated chronic impacts in the mitogen response in parr 15 months post-exposure as larvae. The proliferative response of AKLs to the mitogens concanavalin A (CON A), phytohemaglutinnin-P (PHA-P), pokeweed mitogen (PWM), and lipopolysaccharide were used as an indice of immunomodulation. The proliferative response to the T-cell mitogens CON A and PHA-P was significantly increased in the 10 ??g L-1 group (n = 10; P = 0.043 and 0.002, respectively) immediately following exposure of smolts. Additionally, The PHA-P response was significantly increased in the 1 ??g L-1 exposure group (n = 10, P = 0.036). In fish treated as larvae and tested 15 months later, the PHA-P sensitive populations exhibited elevated proliferation in the 1 and 10 ??g L-1 groups (n = 12, P < 0.04) relative to the vehicle control while the PWM response was significantly increased (n = 12, P = 0.036) only in the 10 ??g L-1 treated groups. These results demonstrate an immunomodulatory effect of PCBs on T-cell mitogen sensitive populations of lymphocytes in Atlantic salmon as well as long-term immunomodulation in PHA-P and PWM sensitive populations. ?? 2005 Elsevier B.V. All rights reserved.

Validity of semi-quantitative scale for brain MRI in unilateral cerebral palsy due to periventricular white matter lesions: Relationship with hand sensorimotor function and structural connectivity

PubMed Central

Fiori, Simona; Guzzetta, Andrea; Pannek, Kerstin; Ware, Robert S.; Rossi, Giuseppe; Klingels, Katrijn; Feys, Hilde; Coulthard, Alan; Cioni, Giovanni; Rose, Stephen; Boyd, Roslyn N.

2015-01-01

Aim To provide first evidence of construct validity of a semi-quantitative scale for brain structural MRI (sqMRI scale) in children with unilateral cerebral palsy (UCP) secondary to periventricular white matter (PWM) lesions, by examining the relationship with hand sensorimotor function and whole brain structural connectivity. Methods Cross-sectional study of 50 children with UCP due to PWM lesions using 3 T (MRI), diffusion MRI and assessment of hand sensorimotor function. We explored the relationship of lobar, hemispheric and global scores on the sqMRI scale, with fractional anisotropy (FA), as a measure of brain white matter microstructure, and with hand sensorimotor measures (Assisting Hand Assessment, AHA; Jebsen–Taylor Test for Hand Function, JTTHF; Melbourne Assessment of Unilateral Upper Limb Function, MUUL; stereognosis; 2-point discrimination). Results Lobar and hemispheric scores on the sqMRI scale contralateral to the clinical side of hemiplegia correlated with sensorimotor paretic hand function measures and FA of a number of brain structural connections, including connections of brain areas involved in motor control (postcentral, precentral and paracentral gyri in the parietal lobe). More severe lesions correlated with lower sensorimotor performance, with the posterior limb of internal capsule score being the strongest contributor to impaired hand function. Conclusion The sqMRI scale demonstrates first evidence of construct validity against impaired motor and sensory function measures and brain structural connectivity in a cohort of children with UCP due to PWM lesions. More severe lesions correlated with poorer paretic hand sensorimotor function and impaired structural connectivity in the hemisphere contralateral to the clinical side of hemiplegia. The quantitative structural MRI scoring may be a useful clinical tool for studying brain structure–function relationships but requires further validation in other populations of CP. PMID:26106533

A status update on EUMETSAT programmes and plans

NASA Astrophysics Data System (ADS)

Klaes, K. Dieter

2017-09-01

The mandate of EUMETSAT is providing space observations for operational meteorology and climate monitoring. EUMETSAT operates geostationary and sun-synchronous polar orbiting satellites through mandatory programmes. Optional programmes provide further observations for altimetry and oceanography. EUMETSAT makes available data from partner agencies' satellites to the user community through third party programmes. The current fleet of operational geostationary spacecraft comprises Meteosat-7, which is the last satellite of the first generation and the four satellites of the Second Generation of Meteosat (MSG), Meteosat-8, Meteosat-9, Meteosat-10 and Meteosat-11. The EUMETSAT Polar System (EPS) provides data from sun-synchronous polar orbit with currently two satellites: Metop-B, the second of a series of three satellites, launched in September 2012 and currently the prime satellite, and Metop-A, the first of the series, in orbit since October 2006. These satellites are part of the Initial Joint Polar System (IJPS) together with the US. EUMETSAT's first optional programme continues to provide data from the Jason-2 satellite since summer 2008. The follow on satellite Jason-3 was successfully launched and commissioned in 2016 and is now providing the reference altimetry mission. To assure continuity in the mandatory missions the development of Meteosat Third Generation (MTG) is ongoing. The EPS-SG EPS Second generation) programme is now under full development. In the frame of the Copernicus Programme EUMETSAT operates the Sentinel-3A satellite, which was launched in February 2016. EUMETSAT is providing operational marine products from the Sentinel-3A satellite. Sentinel-3B, is scheduled to be launched early 2018.

A founder project: marketing the domestication baseline for forest trees

Treesearch

C. G. Williams; Floyd E. Bridgwater; C. Dana Nelson

2004-01-01

One of the most apparent benefits of forest genomics programmes is to provide genotypic information on the original selections of tree improvement programmes worldwide. In many breeding programmes, brances from these selections were grafted onto seedlings and the grafted seedlings composed the first seed orchards for planting programmes. with advanced generation...

Photoacoustic-Based-Close-Loop Temperature Control for Nanoparticle Hyperthermia.

PubMed

Xiaohua, Feng; Fei, Gao; Yuanjin, Zheng

2015-07-01

Hyperthermia therapy requires tight temperature control to achieve selective killing of cancerous tissue with minimal damage on surrounding healthy tissues. To this end, accurate temperature monitoring and subsequent heating control are critical. However, an economic, portable, and real-time temperature control solution is currently lacking. To bridge this gap, we present a novel portable close-loop system for hyperthermia temperature control, in which photoacoustic technique is proposed for noninvasive real-time temperature measurement. Exploiting the high sensitivity of photoacoustics, the temperature is monitored with an accuracy of around 0.18 °C and then fed back to a controller implemented on field programmable gate array (FPGA) for temperature control. Dubbed as portable hyperthermia feedback controller (pHFC), it stabilizes the temperature at preset values by regulating the hyperthermia power with a proportional-integral-derivative (PID) algorithm; and to facilitate digital implementation, the pHFC further converts the PID output into switching values (0 and 1) with the pulse width modulation (PWM) algorithm. Proof-of-concept hyperthermia experiments demonstrate that the pHFC system is able to bring the temperature from baseline to predetermined value with an accuracy of 0.3° and a negligible temperature overshoot. The pHFC can potentially be translated to clinical applications with customized hyperthermia system design. This paper can facilitate future efforts in seamless integration of close-loop temperature control solution and various clinical hyperthermia systems.

Effects of complete vitamin and mineral supplementation in full potential all-milk diets on growth and health of Holstein bull calves

USDA-ARS?s Scientific Manuscript database

Pre-ruminant Holstein bull calves were fed two diets of pasteurized whole milk (PWM) in amounts that either limited intake or that maximized intake according to common commercial practice. Diets then were either supplemented or not supplemented with a full complement of vitamins and trace minerals ...

Field programmable gate arrays: Evaluation report for space-flight application

NASA Technical Reports Server (NTRS)

Sandoe, Mike; Davarpanah, Mike; Soliman, Kamal; Suszko, Steven; Mackey, Susan

1992-01-01

Field Programmable Gate Arrays commonly called FPGA's are the newer generation of field programmable devices and offer more flexibility in the logic modules they incorporate and in how they are interconnected. The flexibility, the number of logic building blocks available, and the high gate densities achievable are why users find FPGA's attractive. These attributes are important in reducing product development costs and shortening the development cycle. The aerospace community is interested in incorporating this new generation of field programmable technology in space applications. To this end, a consortium was formed to evaluate the quality, reliability, and radiation performance of FPGA's. This report presents the test results on FPGA parts provided by ACTEL Corporation.

Programmable Pulse Generator for Aditya Gas Puffing System

NASA Astrophysics Data System (ADS)

Patel, Narendra; Chavda, Chhaya; Bhatt, S. B.; Chattopadhyay, Prabal; Saxena, Y. C.

2012-11-01

In the Aditya Tokamak, one of primary requirement for plasma generation is to feed the required quantity of the fuel gas prior to plasma shot. Gas feed system mainly consists of piezoelectric gas leak valve and gas reservoir. The Hydrogen gas is prior to 300ms loop voltage for the duration of 4 msec to 7 msec. Gas is puffed during the shot for required plasma parameters and to increase plasma density using the same system. The valve is controlled by either continuous voltage or pulses of different width, amplitude and delay with respect to loop voltage. These voltage pulses are normally applied through standard pulse generator. The standard pulse generator is replaced by micro controller based in housed developed programmable pulse generator system consists of in built power supply, BNC input for external trigger, BNC output and serial interface. This programmable pulse generator is successfully tested and is in operation for gas puffing during ADITYA Tokamak experiments. The paper discusses the design and development aspect of the system.

LWIR pupil imaging and prospects for background compensation

NASA Astrophysics Data System (ADS)

LeVan, Paul; Sakoglu, Ünal; Stegall, Mark; Pierce, Greg

2015-08-01

A previous paper described LWIR Pupil Imaging with a sensitive, low-flux focal plane array, and behavior of this type of system for higher flux operations as understood at the time. We continue this investigation, and report on a more detailed characterization of the system over a broad range of pixel fluxes. This characterization is then shown to enable non-uniformity correction over the flux range, using a standard approach. Since many commercial tracking platforms include a "guider port" that accepts pulse width modulation (PWM) error signals, we have also investigated a variation on the use of this port to "dither" the tracking platform in synchronization with the continuous collection of infrared images. The resulting capability has a broad range of applications that extend from generating scene motion in the laboratory for quantifying performance of "realtime, scene-based non-uniformity correction" approaches, to effectuating subtraction of bright backgrounds by alternating viewing aspect between a point source and adjacent, source-free backgrounds.

Design of a temperature control system using incremental PID algorithm for a special homemade shortwave infrared spatial remote sensor based on FPGA

NASA Astrophysics Data System (ADS)

Xu, Zhipeng; Wei, Jun; Li, Jianwei; Zhou, Qianting

2010-11-01

An image spectrometer of a spatial remote sensing satellite requires shortwave band range from 2.1μm to 3μm which is one of the most important bands in remote sensing. We designed an infrared sub-system of the image spectrometer using a homemade 640x1 InGaAs shortwave infrared sensor working on FPA system which requires high uniformity and low level of dark current. The working temperature should be -15+/-0.2 Degree Celsius. This paper studies the model of noise for focal plane array (FPA) system, investigated the relationship with temperature and dark current noise, and adopts Incremental PID algorithm to generate PWM wave in order to control the temperature of the sensor. There are four modules compose of the FPGA module design. All of the modules are coded by VHDL and implemented in FPGA device APA300. Experiment shows the intelligent temperature control system succeeds in controlling the temperature of the sensor.

A three-channel LED driver with single line transportation technique

NASA Astrophysics Data System (ADS)

Yu, Caideng; Du, Yiying; Jiang, Qiao; Zhou, Yun; Lv, Jian

2012-10-01

Designed a three-channel LED driver, realized the single-wire transmission of cascade signal between the drive IC of LED. Including the MCU digital interface, date register, clock synchronization, PWM grayscale adjustment circuit, as well as high voltage driver circuit for LED, etc… The driver control LED displaying 256 gray. Chip will generate synchronous sampling clock signals according to the received serial signals, when 24 bits dates have been received, the output pin begins to transport the dates followed-up which are automotive shaped to the input of the next chip. When the date receiving becomes low level that represent RESET, the red, green and blue channels will export different signals based on different input dates. Through the external MCU, it is realized the Separate luminance, and by connecting chips in series it achieved the control of outdoor big screen' colorful display. The automatic shaping forward technique makes the number of chips cascading immune to the limitations of signal transmission, but only limited by the refresh speed.

PI and fuzzy logic controllers for shunt Active Power Filter--a report.

PubMed

P, Karuppanan; Mahapatra, Kamala Kanta

2012-01-01

This paper presents a shunt Active Power Filter (APF) for power quality improvements in terms of harmonics and reactive power compensation in the distribution network. The compensation process is based only on source current extraction that reduces the number of sensors as well as its complexity. A Proportional Integral (PI) or Fuzzy Logic Controller (FLC) is used to extract the required reference current from the distorted line-current, and this controls the DC-side capacitor voltage of the inverter. The shunt APF is implemented with PWM-current controlled Voltage Source Inverter (VSI) and the switching patterns are generated through a novel Adaptive-Fuzzy Hysteresis Current Controller (A-F-HCC). The proposed adaptive-fuzzy-HCC is compared with fixed-HCC and adaptive-HCC techniques and the superior features of this novel approach are established. The FLC based shunt APF system is validated through extensive simulation for diode-rectifier/R-L loads. Copyright © 2011 ISA. Published by Elsevier Ltd. All rights reserved.

Pulsed Magnetic Welding for Advanced Core and Cladding Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, Guoping; Yang, Yong

2013-12-19

To investigate a solid-state joining method, pulsed magnetic welding (PMW), for welding the advanced core and cladding steels to be used in Generation IV systems, with a specific application for fuel pin end-plug welding. As another alternative solid state welding technique, pulsed magnetic welding (PMW) has not been extensively explored on the advanced steels. The resultant weld can be free from microstructure defects (pores, non-metallic inclusions, segregation of alloying elements). More specifically, the following objectives are to be achieved: 1. To design a suitable welding apparatus fixture, and optimize welding parameters for repeatable and acceptable joining of the fuel pinmore » end-plug. The welding will be evaluated using tensile tests for lap joint weldments and helium leak tests for the fuel pin end-plug; 2 Investigate the microstructural and mechanical properties changes in PMW weldments of proposed advanced core and cladding alloys; 3. Simulate the irradiation effects on the PWM weldments using ion irradiation.« less

Closed-loop torque feedback for a universal field-oriented controller

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Doncker, R.W.A.A.; King, R.D.; Sanza, P.C.

A torque feedback system is employed in a universal field-oriented (UFO) controller to tune a torque-producing current command and a slip frequency command in order to achieve robust torque control of an induction machine even in the event of current regulator errors and during transitions between pulse width modulated (PWM) and square wave modes of operation. 1 figure.

Closed-loop torque feedback for a universal field-oriented controller

DOEpatents

De Doncker, R.W.A.A.; King, R.D.; Sanza, P.C.; Haefner, K.B.

1992-11-24

A torque feedback system is employed in a universal field-oriented (UFO) controller to tune a torque-producing current command and a slip frequency command in order to achieve robust torque control of an induction machine even in the event of current regulator errors and during transitions between pulse width modulated (PWM) and square wave modes of operation. 1 figure.

Closed-loop torque feedback for a universal field-oriented controller

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Doncker, Rik W. A. A.; King, Robert D.; Sanza, Peter C.

A torque feedback system is employed in a universal field-oriented (UFO) controller to tune a torque-producing current command and a slip frequency command in order to achieve robust torque control of an induction machine even in the event of current regulator errors and during transitions between pulse width modulated (PWM) and square wave modes of operation.

Development of an Adolescent Alcohol Misuse Intervention Based on the Prototype Willingness Model: A Delphi Study

ERIC Educational Resources Information Center

Davies, Emma; Martin, Jilly; Foxcroft, David

2016-01-01

Purpose: The purpose of this paper is to report on the use of the Delphi method to gain expert feedback on the identification of behaviour change techniques (BCTs) and development of a novel intervention to reduce adolescent alcohol misuse, based on the Prototype Willingness Model (PWM) of health risk behaviour. Design/methodology/approach: Four…

Initiation-promotion skin carcinogenesis and immunological competence.

PubMed

Curtis, G L; Stenbäck, F; Ryan, W L

1975-10-01

The immune competence of mice during initiation-promotion skin carcinogenesis was determined by skin allograft rejection and lymphocyte mitogenesis. The carcinogen 7, 12-dimethylbenzanthracene inhibited the cellular immune competence of mice while lymphocytes from croton oil treated mice had enhanced PWM response. Chlorphenesin, a stimulator of cellular immunity, was found to inhibit tumorigenesis in initiation-promotion skin carcinogenesis when injected during promotion.

Intentions and willingness to drive while drowsy among university students: An application of an extended theory of planned behavior model.

PubMed

Lee, Clark J; Geiger-Brown, Jeanne; Beck, Kenneth H

2016-08-01

A web-based questionnaire was used to assess the utility of constructs from the Theory of Planned Behavior (TPB) and the Prototype Willingness Model (PWM) to predict intentions and willingness to engage in drowsy driving in a sample of 450 university students. Those students who reported more favorable attitudes and subjective norm and greater perceived control and willingness in relation to drowsy driving behavior were more likely to report stronger intentions to engage in drowsy driving behavior. Augmenting the TPB constructs with the PWM construct of willingness significantly explained up to an additional 8 percent of the variance in drowsy driving intention. Perceived behavioral control and willingness were consistently the strongest predictors of drowsy driving intention in the augmented model, which together with the control (personal) variables explained up to 70 percent of the variance in intention. Thus, the Theory of Planned Behavior and the Prototype Willingness Model may be useful for understanding motivational influences on drowsy driving behavior in young people and present promising theoretical frameworks for designing more effective interventions against drowsy driving in this population. Copyright © 2016 Elsevier Ltd. All rights reserved.

Using Pulse Width Modulation for Wireless Transmission of Neural Signals in Multichannel Neural Recording Systems

PubMed Central

Yin, Ming; Ghovanloo, Maysam

2013-01-01

We have used a well-known technique in wireless communication, pulse width modulation (PWM) of time division multiplexed (TDM) signals, within the architecture of a novel wireless integrated neural recording (WINeR) system. We have evaluated the performance of the PWM-based architecture and indicated its accuracy and potential sources of error through detailed theoretical analysis, simulations, and measurements on a setup consisting of a 15-channel WINeR prototype as the transmitter and two types of receivers; an Agilent 89600 vector signal analyzer and a custom wideband receiver, with 36 and 75 MHz of maximum bandwidth, respectively. Furthermore, we present simulation results from a realistic MATLAB-Simulink model of the entire WINeR system to observe the system behavior in response to changes in various parameters. We have concluded that the 15-ch WINeR prototype, which is fabricated in a 0.5-μm standard CMOS process and consumes 4.5 mW from ±1.5 V supplies, can acquire and wirelessly transmit up to 320 k-samples/s to a 75-MHz receiver with 8.4 bits of resolution, which is equivalent to a wireless data rate of ~ 2.26 Mb/s. PMID:19497823

Highly flexible pulse programmer for NMR applications

NASA Technical Reports Server (NTRS)

Dart, J.; Burum, D. P.; Rhim, W. K.

1980-01-01

A pulse generator for NMR application is described. Eighteen output channels are provided to allow use in single and double resonance experiments. Complex pulse sequences may be generated by loading instructions into a 256-word by 16-bit program memory. Features of the pulse generator include programmable time delays from 0.5 micros to 1000 s, branching and looping instructions, and the ability to be loaded and operated either manually or from a PDP-11/10 computer.

Problem Solving and Immigrant Student Mathematics and Science Achievement: Multination Findings from the Programme for International Student Assessment (PISA)

ERIC Educational Resources Information Center

Martin, Andrew J.; Liem, Gregory A. D.; Mok, Magdalena M. C.; Xu, Jacob

2012-01-01

The present study investigates problem-solving skill alongside more widely recognized settlement and sociodemographic factors in first-generation (1G) and second-generation (2G) immigrant students' science and mathematics achievement. A total of 113,767 students (ages 15-16 years) from 17 countries were drawn from the 2003 Programme for…

Genome Editing of Monkey.

PubMed

Liu, Zhen; Cai, Yijun; Sun, Qiang

2017-01-01

Gene-modified monkey models would be particularly valuable in biomedical and neuroscience research. Virus-based transgenic and programmable nucleases-based site-specific gene editing methods (TALEN, CRISPR-cas9) enable the generation of gene-modified monkeys with gain or loss of function of specific genes. Here, we describe the generation of transgenic and knock-out (KO) monkeys with high efficiency by lentivirus and programmable nucleases.

Defense Automation Resources Management Manual

DTIC Science & Technology

1988-09-01

Electronic Command Signals Programmer, Plugboard Programmers Punch, Card Punch, Paper Tape Reader, Character Reader-Generator, Time Cards Reader...Multiplexor-Shift Register Group Multiplier Panel Control, Plugboard Panel, Interconnection, Digital Computer Panel, Meter-Attenuator, Tape Recorder PC Cards...Perforator, Tape Plug-In Unit Potentiometer, Coefficient, Analog Computer Programmer, Plugboard Punch, Paper Tape Racks Reader, Time Code Reader

Demand generation and social mobilisation for integrated community case management (iCCM) and child health: Lessons learned from successful programmes in Niger and Mozambique.

PubMed

Sharkey, Alyssa B; Martin, Sandrine; Cerveau, Teresa; Wetzler, Erica; Berzal, Rocio

2014-12-01

We present the approaches used in and outcomes resulting from integrated community case management (iCCM) programmes in Niger and Mozambique with a strong focus on demand generation and social mobilisation. We use a case study approach to describe the programme and contextual elements of the Niger and Mozambique programmes. Awareness and utilisation of iCCM services and key family practices increased following the implementation of the Niger and Mozambique iCCM and child survival programmes, as did care-seeking within 24 hours and care-seeking from appropriate, trained providers in Mozambique. These approaches incorporated interpersonal communication activities and community empowerment/participation for collective change, partnerships and networks among key stakeholder groups within communities, media campaigns and advocacy efforts with local and national leaders. iCCM programmes that train and equip community health workers and successfully engage and empower community members to adopt new behaviours, have appropriate expectations and to trust community health workers' ability to assess and treat illnesses can lead to improved care-seeking and utilisation, and community ownership for iCCM.

An update on EUMETSAT programmes and plans

NASA Astrophysics Data System (ADS)

Klaes, K. Dieter; Holmlund, Kenneth

2016-09-01

EUMETSAT is providing space based observations for operational meteorology and climate monitoring. The observations are measured by geostationary and sun-synchronous polar orbiting satellites in the frame of mandatory programmes. In the frame of optional programmes further observations for altimetry and oceanography are collected and disseminated. In the frame of third party programmes, EUMETSAT makes available data from other agencies' satellites to the user community. Since summer 2015 MSG-4 complements the current operational fleet of operational geostationary spacecraft, Meteosat-7, which is the last satellite of the first generation and the three satellites of the Second Generation of Meteosat, Meteosat-8, Meteosat-9 and Meteosat-10. MSG-4 became Meteosat-11 and was stored in orbit after successful commissioning. Two satellites of the EUMETSAT Polar System (EPS) provide data from sunsynchronous polar orbit. Metop-B, the second of a series of three satellites, launched in September 2012 and Metop-A, the first of the series, in orbit since October 2006 provide operational services. The satellites belong to the Initial Joint Polar System (IJPS) with the US. EUMETSAT's first optional programme continues to provide data from the Jason-2 satellite since summer 2008. As follow on the Jason-3 satellite was launched in January 2016 and is currently in commissioning. To assure continuity development of Meteosat Third Generation (MTG) is ongoing. The EPS-SG programme was fully approved in summer 2015. In the frame of the Copernicus Programme (formerly GMES (Global Monitoring for Environment and Security)) EUMETSAT will operate the marine part of the Sentinel-3 satellite. It was launched in February 2016 and is currently under commissioning.

21 CFR Appendix B to Subpart B of... - Scope of Product Coverage

Code of Federal Regulations, 2013 CFR

2013-04-01

... Portable air compressor 2 Cardiovascular Panel Cardiovascular Diagnostic 870.1425 Programmable diagnostic... Pacemaker & Accessories 870.1750 External programmable pacemaker pulse generator 2 870.3630 Pacemaker...

21 CFR Appendix B to Subpart B of... - Scope of Product Coverage

Code of Federal Regulations, 2014 CFR

2014-04-01

... Portable air compressor 2 Cardiovascular Panel Cardiovascular Diagnostic 870.1425 Programmable diagnostic... Pacemaker & Accessories 870.1750 External programmable pacemaker pulse generator 2 870.3630 Pacemaker...

21 CFR Appendix B to Subpart B of... - Scope of Product Coverage

Code of Federal Regulations, 2012 CFR

2012-04-01

... Portable air compressor 2 Cardiovascular Panel Cardiovascular Diagnostic 870.1425 Programmable diagnostic... Pacemaker & Accessories 870.1750 External programmable pacemaker pulse generator 2 870.3630 Pacemaker...

[Study on a wireless energy transmission system for the noninvasive examination micro system inside alimentary tracts].

PubMed

He, Xiu; Yan, Guo-Zheng; Wang, Fu-Min

2008-01-01

A wireless energy transmission system for the MEMS system inside alimentary tracts is reported here in the paper. It consists of an automatic frequency tracking circuit of phase lock loop and phase shift PWM control circuit. Experimental results show that the energy transmission system is capable of automatic frequency-tracking and transmission power-adjusting and has stable received energy.

Single event effects in pulse width modulation controllers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Penzin, S.H.; Crain, W.R.; Crawford, K.B.

1996-12-01

SEE testing was performed on pulse width modulation (PWM) controllers which are commonly used in switching mode power supply systems. The devices are designed using both Set-Reset (SR) flip-flops and Toggle (T) flip-flops which are vulnerable to single event upset (SEU) in a radiation environment. Depending on the implementation of the different devices the effect can be significant in spaceflight hardware.

Pre-market version of a commercially available hearing instrument with a tinnitus sound generator: feasibility of evaluation in a clinical trial.

PubMed

Sereda, Magdalena; Davies, Jeff; Hall, Deborah A

2017-04-01

This report considers feasibility of conducting a UK trial of combination devices for tinnitus, using data from the study which evaluated different listener programmes available within the pre-market version of Oticon Alta with Tinnitus Sound Generator. Open and closed questions addressed the following feasibility issues: (1) Participant recruitment; (2) Device acceptability; (3) Programme preferences in different self-nominated listening situations; (4) Usability; (5) Compliance; (6) Adverse events. Eight current combination hearing aid users (all males) aged between 62-72 years (mean age 67.25 years, SD = 3.8). All eight participants reported the physical aspects and noise options on the experimental device to be acceptable. Programmes with amplification and masking features were equally preferred over the basic amplification-only programme. Individual preferences for the different programme options varied widely, both across participants and across listening situations. A set of recommendations for future trials were formulated which calls for more "real world" trial design rather than tightly controlling the fitting procedure.

Large-scale road safety programmes in low- and middle-income countries: an opportunity to generate evidence.

PubMed

Hyder, Adnan A; Allen, Katharine A; Peters, David H; Chandran, Aruna; Bishai, David

2013-01-01

The growing burden of road traffic injuries, which kill over 1.2 million people yearly, falls mostly on low- and middle-income countries (LMICs). Despite this, evidence generation on the effectiveness of road safety interventions in LMIC settings remains scarce. This paper explores a scientific approach for evaluating road safety programmes in LMICs and introduces such a road safety multi-country initiative, the Road Safety in 10 Countries Project (RS-10). By building on existing evaluation frameworks, we develop a scientific approach for evaluating large-scale road safety programmes in LMIC settings. This also draws on '13 lessons' of large-scale programme evaluation: defining the evaluation scope; selecting study sites; maintaining objectivity; developing an impact model; utilising multiple data sources; using multiple analytic techniques; maximising external validity; ensuring an appropriate time frame; the importance of flexibility and a stepwise approach; continuous monitoring; providing feedback to implementers, policy-makers; promoting the uptake of evaluation results; and understanding evaluation costs. The use of relatively new approaches for evaluation of real-world programmes allows for the production of relevant knowledge. The RS-10 project affords an important opportunity to scientifically test these approaches for a real-world, large-scale road safety evaluation and generate new knowledge for the field of road safety.

Results from the UK 3rd generation programme: Albion

NASA Astrophysics Data System (ADS)

McEwen, R. K.; Axcell, C.; Knowles, P.; Hoade, K. P.; Wilson, M.; Dennis, P. N. J.; Backhouse, P.; Gordon, N. T.

2008-10-01

Following the development of 1st Generation systems in the 1970s, thermal imaging has been in service with the UK armed forces for over 25 years and has proven itself to be a battle winning technology. More recently the wider accessibility to similar technologies within opposing forces has reduced the military advantage provided by these 1st Generation systems and a clear requirement has been identified by the UK MOD for thermal imaging sensors providing increased detection, recognition and identification (DRI) ranges together with a simplified logistical deployment burden and reduced through-life costs. In late 2005, the UK MOD initiated a programme known as "Albion" to develop high performance 3rd Generation single waveband infrared detectors to meet this requirement. At the same time, under a separate programme supporting higher risk technology, a dual waveband infrared detector was also developed. The development phase of the Albion programme has now been completed and prototype detectors are now available and have been integrated into demonstration thermal imaging cameras. The Albion programme has now progressed into the second phase, incorporating both single and dual waveband devices, focussing on low rate initial production (LRIP) and qualification of the devices for military applications. All of the detectors have been fabricated using cadmium mercury telluride material (CMT), grown by metal organic vapour phase epitaxy (MOVPE) on low cost, gallium arsenide (GaAs) substrates and bump bonded to the silicon read out circuit (ROIC). This paper discusses the design features of the 3rd Generation detectors developed in the UK together with the results obtained from the prototype devices both in the laboratory and when integrated into field deployable thermal imaging cameras.

The Evidence Base for Early Childhood Education and Care Programme Investment: What We Know, What We Don't Know

ERIC Educational Resources Information Center

White, Linda A.; Prentice, Susan; Perlman, Michal

2015-01-01

An expanding body of research demonstrates that high quality early childhood education and care (ECEC) programmes generate positive outcomes for children; in response, policy makers in a number of countries are making significant programme investments. No research consensus, however, has emerged around the specific types of policy intervention…

Design and implementation of the NaI(Tl)/CsI(Na) detectors output signal generator

NASA Astrophysics Data System (ADS)

Zhou, Xu; Liu, Cong-Zhan; Zhao, Jian-Ling; Zhang, Fei; Zhang, Yi-Fei; Li, Zheng-Wei; Zhang, Shuo; Li, Xu-Fang; Lu, Xue-Feng; Xu, Zhen-Ling; Lu, Fang-Jun

2014-02-01

We designed and implemented a signal generator that can simulate the output of the NaI(Tl)/CsI(Na) detectors' pre-amplifier onboard the Hard X-ray Modulation Telescope (HXMT). Using the development of the FPGA (Field Programmable Gate Array) with VHDL language and adding a random constituent, we have finally produced the double exponential random pulse signal generator. The statistical distribution of the signal amplitude is programmable. The occurrence time intervals of the adjacent signals contain negative exponential distribution statistically.

Social acceptability and perceived impact of a community-led cash transfer programme in Zimbabwe

PubMed Central

2013-01-01

Background Cash transfer programmes are increasingly recognised as promising and scalable interventions that can promote the health and development of children. However, concerns have been raised about the potential for cash transfers to contribute to social division, jealousy and conflict at a community level. Against this background, and in our interest to promote community participation in cash transfer programmes, we examine local perceptions of a community-led cash transfer programme in Eastern Zimbabwe. Methods We collected and analysed data from 35 individual interviews and three focus group discussions, involving 24 key informants (community committee members and programme implementers), 24 cash transfer beneficiaries, of which four were youth, and 14 non-beneficiaries. Transcripts were subjected to thematic analysis and coding to generate concepts. Results Study participants described the programme as participatory, fair and transparent – reducing the likelihood of jealousy. The programme was perceived to have had a substantial impact on children’s health and education, primarily through aiding parents and guardians to better cater for their children’s needs. Moreover, participants alluded to the potential of the programme to facilitate more transformational change, for example by enabling families to invest money in assets and income generating activities and by promoting a community-wide sense of responsibility for the support of orphaned and vulnerable children. Conclusion Community participation, combined with the perceived impact of the cash transfer programme, led community members to speak enthusiastically about the programme. We conclude that community-led cash transfer programmes have the potential to open up for possibilities of participation and community agency that enable social acceptability and limit social divisiveness. PMID:23587136

Mathematical simulation of power conditioning systems. Volume 1: Simulation of elementary units. Report on simulation methodology

NASA Technical Reports Server (NTRS)

Prajous, R.; Mazankine, J.; Ippolito, J. C.

1978-01-01

Methods and algorithms used for the simulation of elementary power conditioning units buck, boost, and buck-boost, as well as shunt PWM are described. Definitions are given of similar converters and reduced parameters. The various parts of the simulation to be carried out are dealt with; local stability, corrective network, measurements of input-output impedance and global stability. A simulation example is given.

The Interaction between Knowledge and Practice in the Acquisition of Cognitive Skills

DTIC Science & Technology

1992-06-01

by interpreting (in the computer sci- ence sense) the declarative knowledge. During interpretation, new pro- duction rules are constructed which...83224 Toe Uww...y P Jr.o. L J2mx AOrd." ANO 2X Dr. Lado " 0. P.Wm SoodlAd CDR fl.* C. P".1. 3~. , d...ooo. .sd UNrTID KINODOM mN1w o vd.els".a Trosmpeoosmw

Feasibility study of an aerial manipulator interacting with a vertical wall

DTIC Science & Technology

2017-06-01

each blade . Some tests are run with different levels of PWM input and the resultant angular acceleration in each case is measured with the motion...Helicopter Near a Vertical Surface ...................29 Figure 15. Near-Wall Moment for a Single Blade Helicopter. Source: [30]. .............30...with canted propellers is proposed, so that each blade applies thrust with components in the vertical and in the horizontal plane. In Figure 10

The Role of Phonological Working Memory and Environmental Factors in Lexical Development in Italian-Speaking Late Talkers: A One-Year Follow-Up Study

ERIC Educational Resources Information Center

Marini, Andrea; Ruffino, Milena; Sali, Maria Enrica; Molteni, Massimo

2017-01-01

Purpose: This follow-up study assessed (a) the influence of phonological working memory (pWM), home literacy environment, and a family history of linguistic impairments in late talkers (LTs); (b) the diagnostic accuracy of a task of nonword repetition (NWR) in identifying LTs; and (c) the persistence of lexical weaknesses after 10 months. Method:…

Sugar-Binding Profiles of Chitin-Binding Lectins from the Hevein Family: A Comprehensive Study

PubMed Central

Itakura, Yoko; Nakamura-Tsuruta, Sachiko; Kominami, Junko; Tateno, Hiroaki; Hirabayashi, Jun

2017-01-01

Chitin-binding lectins form the hevein family in plants, which are defined by the presence of single or multiple structurally conserved GlcNAc (N-acetylglucosamine)-binding domains. Although they have been used as probes for chito-oligosaccharides, their detailed specificities remain to be investigated. In this study, we analyzed six chitin-binding lectins, DSA, LEL, PWM, STL, UDA, and WGA, by quantitative frontal affinity chromatography. Some novel features were evident: WGA showed almost comparable affinity for pyridylaminated chitotriose and chitotetraose, while LEL and UDA showed much weaker affinity, and DSA, PWM, and STL had no substantial affinity for the former. WGA showed selective affinity for hybrid-type N-glycans harboring a bisecting GlcNAc residue. UDA showed extensive binding to high-mannose type N-glycans, with affinity increasing with the number of Man residues. DSA showed the highest affinity for highly branched N-glycans consisting of type II LacNAc (N-acetyllactosamine). Further, multivalent features of these lectins were investigated by using glycoconjugate and lectin microarrays. The lectins showed substantial binding to immobilized LacNAc as well as chito-oligosaccharides, although the extents to which they bound varied among them. WGA showed strong binding to heavily sialylated glycoproteins. The above observations will help interpret lectin-glycoprotein interactions in histochemical studies and glyco-biomarker investigations. PMID:28556796

Problem Video Gaming Among Children Enrolled in Tertiary Weight Management Programs.

PubMed

Stubblefield, Sam; Datto, George; Phan, Thao-Ly T; Werk, Lloyd N; Stackpole, Kristin; Siegel, Robert; Stratbucker, William; Tucker, Jared M; Christison, Amy L; Hossain, Jobayer; Gentile, Douglas A

2017-02-01

Prior studies show seven percent to nine percent of children demonstrate gaming behaviors that affect a child's ability to function (e.g., problem gaming), but none have examined the association between problem gaming and weight status. The objective of this study was to determine the prevalence of problem gaming among children enrolled in tertiary weight management programs. We administered a computer-based survey to a convenience sample of children aged 11-17 years enrolled in five geographically diverse pediatric weight management (PWM) programs in the COMPASS (Childhood Obesity Multi-Program Analysis and Study System) network. The survey included demographics, gaming characteristics, and a problem gaming assessment. The survey had 454 respondents representing a diverse cohort (53 percent females, 27 percent black, 24 percent Hispanic, 41 percent white) with mean age of 13.7 years. A total of 8.2 percent of respondents met criteria for problem gaming. Problem gamers were more likely to be white, male, play mature-rated games, and report daily play. Children in PWM programs reported problem gaming at the same rate as other pediatric populations. Screening for problem gaming provides an opportunity for pediatricians to address gaming behaviors that may affect the health of children with obesity who already are at risk for worsened health and quality of life.

Problem Video Gaming Among Children Enrolled in Tertiary Weight Management Programs

PubMed Central

Datto, George; Phan, Thao-Ly T.; Werk, Lloyd N.; Stackpole, Kristin; Siegel, Robert; Stratbucker, William; Tucker, Jared M.; Christison, Amy L.; Hossain, Jobayer; Gentile, Douglas A.

2017-01-01

Abstract Prior studies show seven percent to nine percent of children demonstrate gaming behaviors that affect a child's ability to function (e.g., problem gaming), but none have examined the association between problem gaming and weight status. The objective of this study was to determine the prevalence of problem gaming among children enrolled in tertiary weight management programs. We administered a computer-based survey to a convenience sample of children aged 11–17 years enrolled in five geographically diverse pediatric weight management (PWM) programs in the COMPASS (Childhood Obesity Multi-Program Analysis and Study System) network. The survey included demographics, gaming characteristics, and a problem gaming assessment. The survey had 454 respondents representing a diverse cohort (53 percent females, 27 percent black, 24 percent Hispanic, 41 percent white) with mean age of 13.7 years. A total of 8.2 percent of respondents met criteria for problem gaming. Problem gamers were more likely to be white, male, play mature-rated games, and report daily play. Children in PWM programs reported problem gaming at the same rate as other pediatric populations. Screening for problem gaming provides an opportunity for pediatricians to address gaming behaviors that may affect the health of children with obesity who already are at risk for worsened health and quality of life. PMID:28170312

Pulse width modulation-based temperature tracking for feedback control of a shape memory alloy actuator.

PubMed

Ayvali, Elif; Desai, Jaydev P

2014-04-01

This work presents a temperature-feedback approach to control the radius of curvature of an arc-shaped shape memory alloy (SMA) wire. The nonlinear properties of the SMA such as phase transformation and its dependence on temperature and stress make SMA actuators difficult to control. Tracking a desired trajectory is more challenging than controlling just the position of the SMA actuator since the desired path is continuously changing. Consequently, tracking the desired strain directly or tracking the parameters such as temperature and electrical resistance that are related to strain with a model is a challenging task. Temperature-feedback is an attractive approach when direct measurement of strain is not practical. Pulse width modulation (PWM) is an effective method for SMA actuation and it can be used along with a compensator to control the temperature of the SMA. Using the constitutive model of the SMA, the desired temperature profile can be obtained for a given strain trajectory. A PWM-based nonlinear PID controller with a feed-forward heat transfer model is proposed to use temperature-feedback for tracking a desired temperature trajectory. The proposed controller is used during the heating phase of the SMA actuator. The controller proves to be effective in tracking step-wise and continuous trajectories.

Teachers' Experience from a School-Based Collaborative Teacher Professional Development Programme: Reported Impact on Professional Development

ERIC Educational Resources Information Center

Svendsen, Bodil

2016-01-01

The aim of this study was to find out how science teachers who have participated in a one-year school-based collaborative teacher professional development programme, perceive the programme's impact on their professional development. Constant comparative analysis was used on data from three schools to generate the findings in this study. The…

Demand generation and social mobilisation for integrated community case management (iCCM) and child health: Lessons learned from successful programmes in Niger and Mozambique

PubMed Central

Sharkey, Alyssa B; Martin, Sandrine; Cerveau, Teresa; Wetzler, Erica; Berzal, Rocio

2014-01-01

Aim We present the approaches used in and outcomes resulting from integrated community case management (iCCM) programmes in Niger and Mozambique with a strong focus on demand generation and social mobilisation. Methods We use a case study approach to describe the programme and contextual elements of the Niger and Mozambique programmes. Results Awareness and utilisation of iCCM services and key family practices increased following the implementation of the Niger and Mozambique iCCM and child survival programmes, as did care–seeking within 24 hours and care–seeking from appropriate, trained providers in Mozambique. These approaches incorporated interpersonal communication activities and community empowerment/participation for collective change, partnerships and networks among key stakeholder groups within communities, media campaigns and advocacy efforts with local and national leaders. Conclusions iCCM programmes that train and equip community health workers and successfully engage and empower community members to adopt new behaviours, have appropriate expectations and to trust community health workers’ ability to assess and treat illnesses can lead to improved care–seeking and utilisation, and community ownership for iCCM. PMID:25520800

Digitally programmable signal generator and method

DOEpatents

Priatko, G.J.; Kaskey, J.A.

1989-11-14

Disclosed is a digitally programmable waveform generator for generating completely arbitrary digital or analog waveforms from very low frequencies to frequencies in the gigasample per second range. A memory array with multiple parallel outputs is addressed; then the parallel output data is latched into buffer storage from which it is serially multiplexed out at a data rate many times faster than the access time of the memory array itself. While data is being multiplexed out serially, the memory array is accessed with the next required address and presents its data to the buffer storage before the serial multiplexing of the last group of data is completed, allowing this new data to then be latched into the buffer storage for smooth continuous serial data output. In a preferred implementation, a plurality of these serial data outputs are paralleled to form the input to a digital to analog converter, providing a programmable analog output. 6 figs.

Digitally programmable signal generator and method

DOEpatents

Priatko, Gordon J.; Kaskey, Jeffrey A.

1989-01-01

A digitally programmable waveform generator for generating completely arbitrary digital or analog waveforms from very low frequencies to frequencies in the gigasample per second range. A memory array with multiple parallel outputs is addressed; then the parallel output data is latched into buffer storage from which it is serially multiplexed out at a data rate many times faster than the access time of the memory array itself. While data is being multiplexed out serially, the memory array is accessed with the next required address and presents its data to the buffer storage before the serial multiplexing of the last group of data is completed, allowing this new data to then be latched into the buffer storage for smooth continuous serial data output. In a preferred implementation, a plurality of these serial data outputs are paralleled to form the input to a digital to analog converter, providing a programmable analog output.

Laser scanning confocal microscope with programmable amplitude, phase, and polarization of the illumination beam.

PubMed

Boruah, B R; Neil, M A A

2009-01-01

We describe the design and construction of a laser scanning confocal microscope with programmable beam forming optics. The amplitude, phase, and polarization of the laser beam used in the microscope can be controlled in real time with the help of a liquid crystal spatial light modulator, acting as a computer generated hologram, in conjunction with a polarizing beam splitter and two right angled prisms assembly. Two scan mirrors, comprising an on-axis fast moving scan mirror for line scanning and an off-axis slow moving scan mirror for frame scanning, configured in a way to minimize the movement of the scanned beam over the pupil plane of the microscope objective, form the XY scan unit. The confocal system, that incorporates the programmable beam forming unit and the scan unit, has been implemented to image in both reflected and fluorescence light from the specimen. Efficiency of the system to programmably generate custom defined vector beams has been demonstrated by generating a bottle structured focal volume, which in fact is the overlap of two cross polarized beams, that can simultaneously improve both the lateral and axial resolutions if used as the de-excitation beam in a stimulated emission depletion confocal microscope.

Actuator Characterization of Man Portable Precision Maneuver Concepts

DTIC Science & Technology

2014-03-01

brushless DC motors, along with a model of the rotating wing concept and a prototype 40-mm projectile, which was fired through the spark range (14), is... Brushless Electronic Speed Controller) was used to drive the three motor commutator input lines. This controller inputs a pulse-width modulated (PWM...Part II: The Brushless D.C. Motor Drive. IEEE Transactions on Industry Applications 1989, 25 (2), 274–279. 16. Hemati, N.; Leu, M. A Complete

Automated Neuropsychological Assessment Metrics Version 4 (ANAM4): Select Psychometric Properties and Administration Procedures

DTIC Science & Technology

2015-12-01

testing. DISCUSSION: Glutamate and NAA showed similar trends which both had lower mean ratios in the military group across all four voxel locations...subjects. Several research studies had used civilian subjects as a control group and found significant differences. However this may introduce bias to...military group across all four voxel locations and the most significant reduced mean ratios in PWM. They were not correlated therefore likely are

Pulse transmission transmitter including a higher order time derivate filter

DOEpatents

Dress, Jr., William B.; Smith, Stephen F.

2003-09-23

Systems and methods for pulse-transmission low-power communication modes are disclosed. A pulse transmission transmitter includes: a clock; a pseudorandom polynomial generator coupled to the clock, the pseudorandom polynomial generator having a polynomial load input; an exclusive-OR gate coupled to the pseudorandom polynomial generator, the exclusive-OR gate having a serial data input; a programmable delay circuit coupled to both the clock and the exclusive-OR gate; a pulse generator coupled to the programmable delay circuit; and a higher order time derivative filter coupled to the pulse generator. The systems and methods significantly reduce lower-frequency emissions from pulse transmission spread-spectrum communication modes, which reduces potentially harmful interference to existing radio frequency services and users and also simultaneously permit transmission of multiple data bits by utilizing specific pulse shapes.

MTPA control of mechanical sensorless IPMSM based on adaptive nonlinear control.

PubMed

Najjar-Khodabakhsh, Abbas; Soltani, Jafar

2016-03-01

In this paper, an adaptive nonlinear control scheme has been proposed for implementing maximum torque per ampere (MTPA) control strategy corresponding to interior permanent magnet synchronous motor (IPMSM) drive. This control scheme is developed in the rotor d-q axis reference frame using adaptive input-output state feedback linearization (AIOFL) method. The drive system control stability is supported by Lyapunov theory. The motor inductances are online estimated by an estimation law obtained by AIOFL. The estimation errors of these parameters are proved to be asymptotically converged to zero. Based on minimizing the motor current amplitude, the MTPA control strategy is performed by using the nonlinear optimization technique while considering the online reference torque. The motor reference torque is generated by a conventional rotor speed PI controller. By performing MTPA control strategy, the generated online motor d-q reference currents were used in AIOFL controller to obtain the SV-PWM reference voltages and the online estimation of the motor d-q inductances. In addition, the stator resistance is online estimated using a conventional PI controller. Moreover, the rotor position is detected using the online estimation of the stator flux and online estimation of the motor q-axis inductance. Simulation and experimental results obtained prove the effectiveness and the capability of the proposed control method. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

Poverty alleviation programmes in India: a social audit.

PubMed

K Yesudian, C A

2007-10-01

The review highlights the poverty alleviation programmes of the government in the post-economic reform era to evaluate the contribution of these programmes towards reducing poverty in the country. The poverty alleviation programmes are classified into (i) self-employment programmes; (ii) wage employment programmes; (iii) food security programmes; (iv) social security programmes; and (v) urban poverty alleviation programmes. The parameter used for evaluation included utilization of allocated funds, change in poverty level, employment generation and number or proportion of beneficiaries. The paper attempts to go beyond the economic benefit of the programmes and analyzes the social impact of these programmes on the communities where the poor live, and concludes that too much of government involvement is actually an impediment. On the other hand, involvement of the community, especially the poor has led to better achievement of the goals of the programmes. Such endeavours not only reduced poverty but also empowered the poor to find their own solutions to their economic problems. There is a need for decentralization of the programmes by strengthening the panchayat raj institutions as poverty is not merely economic deprivation but also social marginalization that affects the poor most.

Structured Doctoral Education in Hannover - Joint Programme IMPRS-GW and geo-Q RTG

NASA Astrophysics Data System (ADS)

Kawazoe, Fumiko; Bruns, Sandra

2018-02-01

Two structured doctoral programmes that we have in Hannover, the IMPRS on Gravitational Wave Astronomy and SFB on relativistic geodesy and gravimetry with quantum sensors geo-Q, have not only become major resources for education in each field but have also started to provide substantial synergy to members of both programmes. Our strong crossdisciplinary approach to create a joint programme has received excellent feedback not only from researchers inside the programme but also from various external committee. Building on experience that we have acquired over the last decade, we propose to set up a common doctoral programme within the international gravitational wave astronomy and physics. We envisage that with a common doctoral programme we will create a strong team of young researchers who will carry on building a strong network of third generation gravitational wave detectors and observatories.

Higher Efficiency HVAC Motors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flynn, Charles Joseph

The objective of this project was to design and build a cost competitive, more efficient heating, ventilation, and air conditioning (HVAC) motor than what is currently available on the market. Though different potential motor architectures among QMP’s primary technology platforms were investigated and evaluated, including through the building of numerous prototypes, the project ultimately focused on scaling up QM Power, Inc.’s (QMP) Q-Sync permanent magnet synchronous motors from available sub-fractional horsepower (HP) sizes for commercial refrigeration fan applications to larger fractional horsepower sizes appropriate for HVAC applications, and to add multi-speed functionality. The more specific goal became the research, design,more » development, and testing of a prototype 1/2 HP Q-Sync motor that has at least two operating speeds and 87% peak efficiency compared to incumbent electronically commutated motors (EC or ECM, also known as brushless direct current (DC) motors), the heretofore highest efficiency HVACR fan motor solution, at approximately 82% peak efficiency. The resulting motor prototype built achieved these goals, hitting 90% efficiency and .95 power factor at full load and speed, and 80% efficiency and .7 power factor at half speed. Q-Sync, developed in part through a DOE SBIR grant (Award # DE-SC0006311), is a novel, patented motor technology that improves on electronically commutated permanent magnet motors through an advanced electronic circuit technology. It allows a motor to “sync” with the alternating current (AC) power flow. It does so by eliminating the constant, wasteful power conversions from AC to DC and back to AC through the synthetic creation of a new AC wave on the primary circuit board (PCB) by a process called pulse width modulation (PWM; aka electronic commutation) that is incessantly required to sustain motor operation in an EC permanent magnet motor. The Q-Sync circuit improves the power factor of the motor by removing all failure prone capacitors from the power stage. Q-Sync’s simpler electronics also result in higher efficiency because it eliminates the power required by the PCB to perform the obviated power conversions and PWM processes after line synchronous operating speed is reached in the first 5 seconds of operation, after which the PWM circuits drop out and a much less energy intensive “pass through” circuit takes over, allowing the grid-supplied AC power to sustain the motor’s ongoing operation.« less

Nine-channel mid-power bipolar pulse generator based on a field programmable gate array

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haylock, Ben, E-mail: benjamin.haylock2@griffithuni.edu.au; Lenzini, Francesco; Kasture, Sachin

Many channel arbitrary pulse sequence generation is required for the electro-optic reconfiguration of optical waveguide networks in Lithium Niobate. Here we describe a scalable solution to the requirement for mid-power bipolar parallel outputs, based on pulse patterns generated by an externally clocked field programmable gate array. Positive and negative pulses can be generated at repetition rates up to 80 MHz with pulse width adjustable in increments of 1.6 ns across nine independent outputs. Each channel can provide 1.5 W of RF power and can be synchronised with the operation of other components in an optical network such as light sourcesmore » and detectors through an external clock with adjustable delay.« less

IPACS Electronics: Comments on the Original Design and Current Efforts at Langley Research Center

NASA Technical Reports Server (NTRS)

Gowdey, J. C.

1983-01-01

The development of the integrated power altitude control system (IPACS) is described. The power bridge was fabricated, and all major parts are in hand. The bridge was tested with a 1/4 HP motor for another program. The PWM, Control Logic, and upper bridge driver power supply are breadboarded and are debugged prior to starting testing on a passive load. The Hall sensor circuit for detecting rotor position is in design.

SEPP-ZVS High Frequency Inverter Incorporating Auxiliary Switch

NASA Astrophysics Data System (ADS)

Ogiwara, Hiroyuki; Itoi, Misao; Nakaoka, Mutsuo

This paper presents a novel circuit topology to attain ZVS operation of a high frequency inverter over a wide range output power regulation using a PWM control technique by connecting an auxiliary switch to the conventional single ended push-pull (SEPP) ZVS high frequency inverter. A switching current is injected into the main switches via the auxiliary switch only during the short period between its turn-on and off times to supply a current required for its ZVS operation.

Inverter for interfacing advanced energy sources to a utility grid

DOEpatents

Steigerwald, Robert L.

1984-01-01

A transistor is operated in the PWM mode such that a hlaf sine wave of current is delivered first to one-half of a distribution transformer and then the other as determined by steering thyristors operated at the fundamental sinusoidal frequency. Power to the transistor is supplied by a dc source such as a solar array and the power is converted such that a sinusoidal current is injected into a utility at near unity power factor.

Design, Construction and Testing of a Prototype Holonomic Autonomous Vehicle

DTIC Science & Technology

2007-12-01

Circuit A simple 100 kHz crystal oscillator tank circuit using an LM741 opamp was fed to a LM393N comparator . The circuit’s schematic is provided...research in areas that support development of unmanned ground and air battlefield vehicles. Little attention has been paid to applying robotics to...motion control using a single board computer, a pulse width modulation (PWM) and optical isolation circuit, and a low-cost inertial measurement unit

Detection of clonal aberrations by cytogenetic analysis after different culture methods and by FISH in 129 patients with Chronic Lymphocytic Leukemia.

PubMed

Jenderny, Jutta; Goldmann, Claudia; Thede, Rebekka; Ebrecht, Monika; Korioth, Frank

2014-01-01

There are only a few cytogenetic analysis (CA) studies that directly compare the novel cultivation technique using immunostimulatory CpG-oligonucleotide DSP30/interleukin-2 (DSP30/IL2) with other culture methods. Therefore, parallel cultures of peripheral blood of 129 chronic lymphocytic leukemia (CLL) patients were set up in unstimulated cultures, in the presence of pokeweed medium (PWM), and with DSP30/IL2. Furthermore, CA results were compared with data obtained by FISH. Clonal aberrations were observed by CA in 6% of the cases in unstimulated cultures, in 27% of the cases with PWM, and in 40% of the cases with DSP30/IL2. Some clonal aberrations were detected by CA only with one culture method. Using 3 different culture methods, clonal aberrations were detected in 41% of the cases by CA and in 71% of the cases by FISH. Altogether, 78% of the cases exhibited clonal aberrations discovered by CA and FISH. Also, CA detected clonal aberrations not targeted by FISH in 7% of the cases, and FISH identified clonal aberrations not detected by CA in 36% of the cases. Our study demonstrates that the combined use of CA with different culture methods together with FISH increases our knowledge of the genetic complexity and heterogeneity in CLL pathogenesis. © 2014 S. Karger AG, Basel.

Detection of chromosomal changes in chronic lymphocytic leukemia using classical cytogenetic methods and FISH: application of rich mitogen mixtures for lymphocyte cultures.

PubMed

Koczkodaj, Dorota; Popek, Sylwia; Zmorzyński, Szymon; Wąsik-Szczepanek, Ewa; Filip, Agata A

2016-04-01

One of the research methods of prognostic value in chronic lymphocytic leukemia (CLL) is cytogenetic analysis. This method requires the presence of appropriate B-cell mitogens in cultures in order to obtain a high mitotic index. The aim of our research was to determine the most effective methods of in vitro B-cell stimulation to maximize the number of metaphases from peripheral blood cells of patients with CLL for classical cytogenetic examination, and then to correlate the results with those obtained using fluorescence in situ hybridization (FISH). The study group involved 50 consecutive patients with CLL. Cell cultures were maintained with the basic composition of culture medium and addition of respective stimulators. We used the following stimulators: Pokeweed Mitogen (PWM), 12-O-tetradecanoylphorbol 13-acetate (TPA), ionophore, lipopolysaccharide (LPS), and CpG-oligonucleotide DSP30. We received the highest mitotic index when using the mixture of PWM+TPA+I+DSP30. With classical cytogenetic tests using banding techniques, numerical and structural aberrations of chromosomes were detected in 46 patients, and no change was found in only four patients. Test results clearly confirmed the legitimacy of using cell cultures enriched with the mixture of cell stimulators and combining classical cytogenetic techniques with the FISH technique in later patient diagnosing. Copyright © 2016 American Federation for Medical Research.

In vitro assessment of silver nanoparticles immunotoxicity.

PubMed

Galbiati, Valentina; Cornaghi, Laura; Gianazza, Elisabetta; Potenza, Marco A; Donetti, Elena; Marinovich, Marina; Corsini, Emanuela

2018-02-01

This study aimed to characterize unwanted immune effects of nanoparticles (NP) using THP-1 cells, human whole blood and enriched peripheral blood monocytes. Commercially available silver NP (AgNP < 100 nm, also confirmed by Single Particle Extinction and Scattering) were used as prototypical NP. Cells were treated with AgNP alone or in combination with classical immune stimuli (i.e. LPS, PHA, PWM) and cytokine assessed; in addition, CD54 and CD86 expression was evaluated in THP-1 cells. AgNP alone induced dose-related IL-8 production in all models, with higher response observed in THP-1 cells, possibly connected to different protein corona formation in bovine versus human serum. AgNP potentiated LPS-induced IL-8 and TNF-α, but not LPS-induced IL-10. AgNP alone induced slight increase in IL-4, and no change in IFN-γ production. While responses to PHA in term of IL-4 and IFN-γ production were not affected, increased PWM-induced IL-4 and IFN-γ production were observed, suggesting potentiation of humoral response. Reduction in PHA-induced IL-10 was observed. Overall, results indicate immunostimulatory effects. THP-1 cells work as well as primary cells, representing a useful and practical alternative, with the awareness that from a physiological point of view the whole blood assay is the one that comes closest to reality. Copyright © 2018 Elsevier Ltd. All rights reserved.

Development of microheaters for gas sensor with an AT-Mega 8535 temperature controller using a PWM (pulse width modulation) method

NASA Astrophysics Data System (ADS)

Megayanti, Meti; Panatarani, Camellia; Joni, I. Made

2016-03-01

Microheater is the main component in gas sensor characterized by their sensitivity, selectivity, and time response of gas sensor which is depend on the microheater temperature stability. A Cu microheater was developed and utilized AT-Mega 8535 controller using a PWM (pulse width modulation) method. This control system is interfaced to the PC to observe the real time temperature response of the microheater. Three initial resistance (R0) variations of microheater were developed in an open loop control system. The power characteristic of designed microheater depends on the specified microheater initial resistance. The smaller R0, the less power required to reach a temperature setting value. The developed microheater was designed to reach a temperature setting value of 250°C having resistance 0.531 Ω for 1.979 Watt and 0.265 Ω for 1.072 Watt respectively. The results of the investigation on the control performances shows microheater-control system achieved operating temperature up to 250°C. The response of the temperature control shows smallest R0 resulted in a high stability with short settling time, short delay time and small ripple for temperature setting values higher than 150°C. The obtained error of microheater temperature with R0 = 0.265 is 8.596 %. It is concluded that the developed microheater can be utilized as a component of a gas sensor.

Novel concept for driving the linear compressor of a micro-miniature split Stirling cryogenic cooler

NASA Astrophysics Data System (ADS)

Maron, V.; Veprik, A.; Finkelstein, L.; Vilenchik, H.; Ziv, I.; Pundak, N.

2009-05-01

New methods of carrying out homeland security and antiterrorist operations call for the development of a new generation of mechanically cooled, portable, battery powered infrared imagers, relying on micro-miniature Stirling cryogenic coolers of rotary or linear types. Since split Stirling linearly driven micro-miniature cryogenic coolers have inherently longer life spans, low vibration export and better aural stealth as compared to their rotary driven rivals, they are more suitable for the above applications. The performance of such cryogenic coolers depends strongly on the efficacy of their electronic drivers. In a traditional approach, the PWM power electronics produce the fixed frequency tonal driving voltage/current, the magnitude of which is modulated via a PID control law so as to maintain the desired focal plane array temperature. The disadvantage of such drivers is that they draw high ripple current from the system's power bus. This results in the need for an oversized DC power supply (battery packs) and power electronic components, low efficiency due to excessive conductive losses and high residual electromagnetic interference which in turn degrades the performance of other systems connected to the same power bus. Without either an active line filter or large and heavy passive filtering, other electronics can not be powered from the same power bus, unless they incorporate heavy filtering at their inputs. The authors present the results of a feasibility study towards developing a novel "pumping" driver consuming essentially constant instant battery power/current without making use of an active or passive filter. In the tested setup, the driver relies on a bidirectional controllable bridge, invertible with the driving frequency, and a fast regulated DC/DC converter which maintains a constant level of current consumed from the DC power supply and thus operates in input current control mode. From the experimental results, the steady-state power consumed by the linear compressor remains the same as compared with the traditional sine wave driver, the voltage and current drawn from the battery pack is essentially free of low frequency ripple (this without use of any kind of filtering) and the overall coefficient of performance of the driver is in excess of 94% over the entire working range of supply voltages. Such a driver free of sine forming PWM stage and have reduced power peaks in all power conversion components.

Individual-level outcomes from a national clinical leadership development programme.

PubMed

Patton, Declan; Fealy, Gerard; McNamara, Martin; Casey, Mary; Connor, Tom O; Doyle, Louise; Quinlan, Christina

2013-08-01

A national clinical leadership development programme was instituted for Irish nurses and midwives in 2010. Incorporating a development framework and leadership pathway and a range of bespoke interventions for leadership development, including workshops, action-learning sets, mentoring and coaching, the programme was introduced at seven pilot sites in the second half of 2011. The programme pilot was evaluated with reference to structure, process and outcomes elements, including individual-level programme outcomes. Evaluation data were generated through focus groups and group interviews, individual interviews and written submissions. The data provided evidence of nurses' and midwives' clinical leadership development through self and observer-reported behaviours and dispositions including accounts of how the programme participants developed and displayed particular clinical leadership competencies. A key strength of the new programme was that it involved interventions that focussed on specific leadership competencies to be developed within the practice context.

Programmable Pulse-Position-Modulation Encoder

NASA Technical Reports Server (NTRS)

Zhu, David; Farr, William

2006-01-01

A programmable pulse-position-modulation (PPM) encoder has been designed for use in testing an optical communication link. The encoder includes a programmable state machine and an electronic code book that can be updated to accommodate different PPM coding schemes. The encoder includes a field-programmable gate array (FPGA) that is programmed to step through the stored state machine and code book and that drives a custom high-speed serializer circuit board that is capable of generating subnanosecond pulses. The stored state machine and code book can be updated by means of a simple text interface through the serial port of a personal computer.

Context Aware Programmable Trackers for the Next Generation Internet

NASA Astrophysics Data System (ADS)

Sousa, Pedro

This work introduces and proposes the concept of context aware programmable trackers for the next generation Internet. The proposed solution gives ground for the development of advanced applications based on the P2P paradigm and will foster collaborative efforts among several network entities (e.g. P2P applications and ISPs). The proposed concept of context aware programmable trackers allows that several peer selection strategies might be supported by a P2P tracker entity able to improve the peer selection decisions according with pre-defined objectives and external inputs provided by specific services. The flexible, adaptive and enhanced peer selection semantics that might be achieved by the proposed solution will contribute for devising novel P2P based services and business models for the future Internet.

Rapid and Programmable Protein Mutagenesis Using Plasmid Recombineering.

PubMed

Higgins, Sean A; Ouonkap, Sorel V Y; Savage, David F

2017-10-20

Comprehensive and programmable protein mutagenesis is critical for understanding structure-function relationships and improving protein function. There is thus a need for robust and unbiased molecular biological approaches for the construction of the requisite comprehensive protein libraries. Here we demonstrate that plasmid recombineering is a simple and robust in vivo method for the generation of protein mutants for both comprehensive library generation as well as programmable targeting of sequence space. Using the fluorescent protein iLOV as a model target, we build a complete mutagenesis library and find it to be specific and comprehensive, detecting 99.8% of our intended mutations. We then develop a thermostability screen and utilize our comprehensive mutation data to rapidly construct a targeted and multiplexed library that identifies significantly improved variants, thus demonstrating rapid protein engineering in a simple protocol.

Programmable assembly of pressure sensors using pattern-forming bacteria.

PubMed

Cao, Yangxiaolu; Feng, Yaying; Ryser, Marc D; Zhu, Kui; Herschlag, Gregory; Cao, Changyong; Marusak, Katherine; Zauscher, Stefan; You, Lingchong

2017-11-01

Biological systems can generate microstructured materials that combine organic and inorganic components and possess diverse physical and chemical properties. However, these natural processes in materials fabrication are not readily programmable. Here, we use a synthetic-biology approach to assemble patterned materials. We demonstrate programmable fabrication of three-dimensional (3D) materials by printing engineered self-patterning bacteria on permeable membranes that serve as a structural scaffold. Application of gold nanoparticles to the colonies creates hybrid organic-inorganic dome structures. The dynamics of the dome structures' response to pressure is determined by their geometry (colony size, dome height, and pattern), which is easily modified by varying the properties of the membrane (e.g., pore size and hydrophobicity). We generate resettable pressure sensors that process signals in response to varying pressure intensity and duration.

Fully digital programmable optical frequency comb generation and application.

PubMed

Yan, Xianglei; Zou, Xihua; Pan, Wei; Yan, Lianshan; Azaña, José

2018-01-15

We propose a fully digital programmable optical frequency comb (OFC) generation scheme based on binary phase-sampling modulation, wherein an optimized bit sequence is applied to phase modulate a narrow-linewidth light wave. Programming the bit sequence enables us to tune both the comb spacing and comb-line number (i.e., number of comb lines). The programmable OFCs are also characterized by ultra-flat spectral envelope, uniform temporal envelope, and stable bias-free setup. Target OFCs are digitally programmed to have 19, 39, 61, 81, 101, or 201 comb lines and to have a 100, 50, 20, 10, 5, or 1 MHz comb spacing. As a demonstration, a scanning-free temperature sensing system using a proposed OFC with 1001 comb lines was also implemented with a sensitivity of 0.89°C/MHz.

RevManHAL: towards automatic text generation in systematic reviews.

PubMed

Torres Torres, Mercedes; Adams, Clive E

2017-02-09

Systematic reviews are a key part of healthcare evaluation. They involve important painstaking but repetitive work. A major producer of systematic reviews, the Cochrane Collaboration, employs Review Manager (RevMan) programme-a software which assists reviewers and produces XML-structured files. This paper describes an add-on programme (RevManHAL) which helps auto-generate the abstract, results and discussion sections of RevMan-generated reviews in multiple languages. The paper also describes future developments for RevManHAL. RevManHAL was created in Java using NetBeans by a programmer working full time for 2 months. The resulting open-source programme uses editable phrase banks to envelop text/numbers from within the prepared RevMan file in formatted readable text of a chosen language. In this way, considerable parts of the review's 'abstract', 'results' and 'discussion' sections are created and a phrase added to 'acknowledgements'. RevManHAL's output needs to be checked by reviewers, but already, from our experience within the Cochrane Schizophrenia Group (200 maintained reviews, 900 reviewers), RevManHAL has saved much time which is better employed thinking about the meaning of the data rather than restating them. Many more functions will become possible as review writing becomes increasingly automated.

Key principles to improve programmes and interventions in complementary feeding.

PubMed

Lutter, Chessa K; Iannotti, Lora; Creed-Kanashiro, Hilary; Guyon, Agnes; Daelmans, Bernadette; Robert, Rebecca; Haider, Rukhsana

2013-09-01

Although there are some examples of successful complementary feeding programmes to promote healthy growth and prevent stunting at the community level, to date there are few, if any, examples of successful programmes at scale. A lack of systematic process and impact evaluations on pilot projects to generate lessons learned has precluded scaling up of effective programmes. Programmes to effect positive change in nutrition rarely follow systematic planning, implementation, and evaluation (PIE) processes to enhance effectiveness over the long term. As a result a set of programme-oriented key principles to promote healthy growth remains elusive. The purpose of this paper is to fill this gap by proposing a set of principles to improve programmes and interventions to promote healthy growth and development. Identifying such principles for programme success has three requirements: rethinking traditional paradigms used to promote improved infant and young child feeding; ensuring better linkages to delivery platforms; and, improving programming. Following the PIE model for programmes and learning from experiences from four relatively large-scale programmes described in this paper, 10 key principles are identified in the areas of programme planning, programme implementation, programme evaluation, and dissemination, replication, and scaling up. Nonetheless, numerous operational research questions remain, some of which are highlighted in this paper. © 2013 John Wiley & Sons Ltd.

Integrated care.

PubMed

Warwick-Giles, Lynsey; Checkland, Kath

2018-03-19

Purpose The purpose of this paper is to try and understand how several organisations in one area in England are working together to develop an integrated care programme. Weick's (1995) concept of sensemaking is used as a lens to examine how the organisations are working collaboratively and maintaining the programme. Design/methodology/approach Qualitative methods included: non-participant observations of meetings, interviews with key stakeholders and the collection of documents relating to the programme. These provided wider contextual information about the programme. Comprehensive field notes were taken during observations and analysed alongside interview transcriptions using NVIVO software. Findings This paper illustrates the importance of the construction of a shared identity across all organisations involved in the programme. Furthermore, the wider policy discourse impacted on how the programme developed and influenced how organisations worked together. Originality/value The role of leaders from all organisations involved in the programme was of significance to the overall development of the programme and the sustained momentum behind the programme. Leaders were able to generate a "narrative of success" to drive the programme forward. This is of particular relevance to evaluators, highlighting the importance of using multiple methods to allow researchers to probe beneath the surface of programmes to ensure that evidence moves beyond this public narrative.

An Airborne Programmable Digital to Video Converter Interface and Operation Manual.

DTIC Science & Technology

1981-02-01

Identify by block number) SCAN CONVERTER VIDEO DISPLAY TELEVISION DISPLAY 20. ABSTRACT (Continue on reverse oide If necessary and Identify by block...programmable cathode ray tube (CRT) controller which is accessed by the CPU to permit operation in a wide variety of modes. The Alphanumeric Generator

The Structural Adjustment Programme and the Elderly in Nigeria.

ERIC Educational Resources Information Center

Ekpenyong, Stephen

1995-01-01

Analyzes the impact of recent economic changes accompanying the introduction of the Structural Adjustment Programme (SAP) and ongoing cultural styles on the aged in Nigeria. Compared to younger generations, the relative position of the elderly has not changed significantly, although the latter's position has deteriorated on dimensions such as…

Re-Situation Challenges for International Students "Becoming" Researchers

ERIC Educational Resources Information Center

Franken, Margaret

2012-01-01

This paper presents data generated during a semester-long programme to support international students from countries in Melanesia and Asia embarking on masters research in education in a New Zealand university. All were scholarship recipients. The researcher-and facilitator-of the programme, was interested in documenting and understanding the…

PATHway: Decision Support in Exercise Programmes for Cardiac Rehabilitation.

PubMed

Filos, Dimitris; Triantafyllidis, Andreas; Chouvarda, Ioanna; Buys, Roselien; Cornelissen, Véronique; Budts, Werner; Walsh, Deirdre; Woods, Catherine; Moran, Kieran; Maglaveras, Nicos

2016-01-01

Rehabilitation is important for patients with cardiovascular diseases (CVD) to improve health outcomes and quality of life. However, adherence to current exercise programmes in cardiac rehabilitation is limited. We present the design and development of a Decision Support System (DSS) for telerehabilitation, aiming to enhance exercise programmes for CVD patients through ensuring their safety, personalising the programme according to their needs and performance, and motivating them toward meeting their physical activity goals. The DSS processes data originated from a Microsoft Kinect camera, a blood pressure monitor, a heart rate sensor and questionnaires, in order to generate a highly individualised exercise programme and improve patient adherence. Initial results within the EU-funded PATHway project show the potential of our approach.

Version 1.00 programmer`s tools used in constructing the INEL RML/analytical radiochemistry sample tracking database and its user interface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Femec, D.A.

This report describes two code-generating tools used to speed design and implementation of relational databases and user interfaces: CREATE-SCHEMA and BUILD-SCREEN. CREATE-SCHEMA produces the SQL commands that actually create and define the database. BUILD-SCREEN takes templates for data entry screens and generates the screen management system routine calls to display the desired screen. Both tools also generate the related FORTRAN declaration statements and precompiled SQL calls. Included with this report is the source code for a number of FORTRAN routines and functions used by the user interface. This code is broadly applicable to a number of different databases.

The ac propulsion system for an electric vehicle, phase 1

NASA Astrophysics Data System (ADS)

Geppert, S.

1981-08-01

A functional prototype of an electric vehicle ac propulsion system was built consisting of a 18.65 kW rated ac induction traction motor, pulse width modulated (PWM) transistorized inverter, two speed mechanically shifted automatic transmission, and an overall drive/vehicle controller. Design developmental steps, and test results of individual components and the complex system on an instrumented test frame are described. Computer models were developed for the inverter, motor and a representative vehicle. A preliminary reliability model and failure modes effects analysis are given.

The ac propulsion system for an electric vehicle, phase 1

NASA Technical Reports Server (NTRS)

Geppert, S.

1981-01-01

A functional prototype of an electric vehicle ac propulsion system was built consisting of a 18.65 kW rated ac induction traction motor, pulse width modulated (PWM) transistorized inverter, two speed mechanically shifted automatic transmission, and an overall drive/vehicle controller. Design developmental steps, and test results of individual components and the complex system on an instrumented test frame are described. Computer models were developed for the inverter, motor and a representative vehicle. A preliminary reliability model and failure modes effects analysis are given.

Adaptive control in series load PWM induction heating inverters

NASA Astrophysics Data System (ADS)

Szelitzky, Tibor; Henrietta Dulf, Eva

2013-12-01

Permanent variations of the electric properties of the load in induction heating equipment make difficult to control the plant. To overcome these disadvantages, the authors propose a new approach based on adaptive control methods. For real plants it is enough to present desired performances or start-up variables for the controller, from which the algorithms tune the controllers by itself. To present the advantages of the proposed controllers, comparisons are made to a PI controller tuned through Ziegler-Nichols method.

Low Temperature Operation of a Switching Power Converter

NASA Technical Reports Server (NTRS)

Anglada-Sanchez, Carlos R.; Perez-Feliciano, David; Ray, Biswajit

1997-01-01

The low temperature operation of a 48 W, 50 kHz, 36/12 V pulse width modulated (PWM) buck de-de power converter designed with standard commercially available components and devices is reported. The efficiency of the converter increased from 85.6% at room temperature (300 K) to 92.0% at liquid nitrogen temperature (77 K). The variation of power MOSFET, diode rectifier, and output filter inductor loss with temperature is discussed. Relevant current, voltage. and power waveforms are also included.

A PWM transistor inverter for an ac electric vehicle drive

NASA Technical Reports Server (NTRS)

Slicker, J. M.

1981-01-01

A prototype system consisting of closely integrated motor, inverter, and transaxle has been built in order to demonstrate the feasibility of a three-phase ac transistorized inverter for electric vehicle applications. The microprocessor-controlled inverter employs monolithic power transistors to drive an oil-cooled, three-phase induction traction motor at a peak output power of 30 kW from a 144 V battery pack. Transistor safe switching requirements are discussed, and a circuit is presented for recovering trapped snubber inductor energy at transistor turn-off.

Ultra-narrow pulse generator with precision-adjustable pulse width

NASA Astrophysics Data System (ADS)

Fu, Zaiming; Liu, Hanglin

2018-05-01

In this paper, a novel ultra-narrow pulse generation approach is proposed. It is based on the decomposition and synthesis of pulse edges. Through controlling their relative delay, an ultra-narrow pulse could be generated. By employing field programmable gate array digital synthesis technology, the implemented pulse generator is with programmable ability. The amplitude of pulse signals is controlled by the radio frequency amplifiers and bias tees, and high precision can be achieved. More importantly, the proposed approach can break through the limitation of device's propagation delay and optimize the resolution and the accuracy of the pulse width significantly. The implemented pulse generator has two channels, whose minimum pulse width, frequency range, and amplitude range are 100 ps, 15 MHz-1.5 GHz, and 0.1 Vpp-1.8 Vpp, respectively. Both resolution of pulse width and channel delay are 1 ps, and amplitude resolution is 10 mVpp.

The IMPACT Common Module - A Low Cost, Reconfigurable Building Block for Next Generation Phased Arrays

DTIC Science & Technology

2016-03-31

The SiGe receiver has two stages of programmable RF filtering and one stage of IF filtering. Each filter can be tuned in center frequency and...distribution unlimited. transmit, with an IF to RF upconversion chain that is split to programmable phase shifters and VGAs at each output port. Figure 2...These are optimized to run on medium grade Field Programmable Gate Arrays (FPGAs), such as the Altera Arria 10, and represent a few of the many

Programmable assembly of pressure sensors using pattern-forming bacteria

PubMed Central

Cao, Yangxiaolu; Feng, Yaying; Ryser, Marc D.; Zhu, Kui; Herschlag, Gregory; Cao, Changyong; Marusak, Katherine; Zauscher, Stefan; You, Lingchong

2017-01-01

Biological systems can generate microstructured materials that combine organic and inorganic components and possess diverse physical and chemical properties. However, these natural processes in materials fabrication are not readily programmable. Here, we use a synthetic-biology approach to mimic such natural processes to assemble patterned materials.. We demonstrate programmable fabrication of three-dimensional (3D) materials by printing engineered self-patterning bacteria on permeable membranes that serve as a structural scaffold. Application of gold nanoparticles to the colonies creates hybrid organic-inorganic dome structures. The dynamics of the dome structures' response to pressure is determined by their geometry (colony size, dome height and pattern), which is easily modified by varying the properties of the membrane (e.g., pore size and hydrophobicity). We generate resettable pressure sensors that process signals in response to varying pressure intensity and duration. PMID:28991268

A flexible microcontroller-based data acquisition device.

PubMed

Hercog, Darko; Gergič, Bojan

2014-06-02

This paper presents a low-cost microcontroller-based data acquisition device. The key component of the presented solution is a configurable microcontroller-based device with an integrated USB transceiver and a 12-bit analogue-to-digital converter (ADC). The presented embedded DAQ device contains a preloaded program (firmware) that enables easy acquisition and generation of analogue and digital signals and data transfer between the device and the application running on a PC via USB bus. This device has been developed as a USB human interface device (HID). This USB class is natively supported by most of the operating systems and therefore any installation of additional USB drivers is unnecessary. The input/output peripheral of the presented device is not static but rather flexible, and could be easily configured to customised needs without changing the firmware. When using the developed configuration utility, a majority of chip pins can be configured as analogue input, digital input/output, PWM output or one of the SPI lines. In addition, LabVIEW drivers have been developed for this device. When using the developed drivers, data acquisition and signal processing algorithms as well as graphical user interface (GUI), can easily be developed using a well-known, industry proven, block oriented LabVIEW programming environment.

Identification of Predictive Cis-Regulatory Elements Using a Discriminative Objective Function and a Dynamic Search Space

PubMed Central

Karnik, Rahul; Beer, Michael A.

2015-01-01

The generation of genomic binding or accessibility data from massively parallel sequencing technologies such as ChIP-seq and DNase-seq continues to accelerate. Yet state-of-the-art computational approaches for the identification of DNA binding motifs often yield motifs of weak predictive power. Here we present a novel computational algorithm called MotifSpec, designed to find predictive motifs, in contrast to over-represented sequence elements. The key distinguishing feature of this algorithm is that it uses a dynamic search space and a learned threshold to find discriminative motifs in combination with the modeling of motifs using a full PWM (position weight matrix) rather than k-mer words or regular expressions. We demonstrate that our approach finds motifs corresponding to known binding specificities in several mammalian ChIP-seq datasets, and that our PWMs classify the ChIP-seq signals with accuracy comparable to, or marginally better than motifs from the best existing algorithms. In other datasets, our algorithm identifies novel motifs where other methods fail. Finally, we apply this algorithm to detect motifs from expression datasets in C. elegans using a dynamic expression similarity metric rather than fixed expression clusters, and find novel predictive motifs. PMID:26465884

Identification of Predictive Cis-Regulatory Elements Using a Discriminative Objective Function and a Dynamic Search Space.

PubMed

Karnik, Rahul; Beer, Michael A

2015-01-01

The generation of genomic binding or accessibility data from massively parallel sequencing technologies such as ChIP-seq and DNase-seq continues to accelerate. Yet state-of-the-art computational approaches for the identification of DNA binding motifs often yield motifs of weak predictive power. Here we present a novel computational algorithm called MotifSpec, designed to find predictive motifs, in contrast to over-represented sequence elements. The key distinguishing feature of this algorithm is that it uses a dynamic search space and a learned threshold to find discriminative motifs in combination with the modeling of motifs using a full PWM (position weight matrix) rather than k-mer words or regular expressions. We demonstrate that our approach finds motifs corresponding to known binding specificities in several mammalian ChIP-seq datasets, and that our PWMs classify the ChIP-seq signals with accuracy comparable to, or marginally better than motifs from the best existing algorithms. In other datasets, our algorithm identifies novel motifs where other methods fail. Finally, we apply this algorithm to detect motifs from expression datasets in C. elegans using a dynamic expression similarity metric rather than fixed expression clusters, and find novel predictive motifs.

DC-DC Type High-Frequency Link DC for Improved Power Quality of Cascaded Multilevel Inverter

NASA Astrophysics Data System (ADS)

Sadikin, Muhammad; Senjyu, Tomonobu; Yona, Atsushi

2013-06-01

Multilevel inverters are emerging as a new breed of power converter options for power system applications. Recent advances in power switching devices enabled the suitability of multilevel inverters for high voltage and high power applications because they are connecting several devices in series without the need of component matching. Usually, a transformerless battery energy storage system, based on a cascaded multilevel inverter, is used as a measure for voltage and frequency deviations. System can be reduced in size, weight, and cost of energy storage system. High-frequency link circuit topology is advantageous in realizing compact and light-weight power converters for uninterruptible power supply systems, new energy systems using photovoltaic-cells, fuel-cells and so on. This paper presents a DC-DC type high-frequency link DC (HFLDC) cascaded multilevel inverter. Each converter cell is implemented a control strategy for two H-bridge inverters that are controlled with the same multicarrier pulse width modulation (PWM) technique. The proposed cascaded multilevel inverter generates lower voltage total harmonic distortion (THD) in comparison with conventional cascaded multilevel inverter. Digital simulations are carried out using PSCAD/EMTDC to validate the performance of the proposed cascaded multilevel inverter.

Multigenerational Learning for Expanding the Educational Involvement of Bilinguals Experiencing Academic Difficulties

ERIC Educational Resources Information Center

Martínez-Álvarez, Patricia

2017-01-01

Focusing on two bilingual children experiencing learning difficulties, I explore the scientific representations these students generate in an afterschool programme where they have opportunities to exercise agency. In the programme, children use a digital camera to document science in their lives and engage in conversations about the products they…

Simulation of Population Processes with a Programmable Pocket Calculator.

ERIC Educational Resources Information Center

Kidd, N. A. C.

1979-01-01

Presents a set of simulation models for use in teaching population dynamics. These models are designed specifically for use with a programmable pocket calculator, and can be used to demonstrate growth of populations with discrete or overlapping generations and also to explore effects of density-dependent and -independent mortality. (Author/CS)

The Effects of Higher Education Programme Characteristics on the Allocation and Performance of the Graduates

ERIC Educational Resources Information Center

Heijke, Hans; Meng, Christoph

2011-01-01

Using a unique European data-set, we investigated the significance of five higher education programme characteristics for the labour market position of the graduates: the academic versus discipline-specific character of the competencies generated; the standardization of these competencies; the combination of working and learning; the…

A grounded theory model for reducing stigma in health professionals in Canada.

PubMed

Knaak, S; Patten, S

2016-08-01

The Mental Health Commission of Canada was formed as a national catalyst for improving the mental health system. One of its initiatives is Opening Minds (OM), whose mandate is to reduce mental health-related stigma. This article reports findings from a qualitative study on antistigma interventions for healthcare providers, which includes a process model articulating key stages and strategies for implementing successful antistigma programmes. The study employed a grounded theory methodology. Data collection involved in-depth interviews with programme stakeholders, direct observation of programmes, a review of programme documents, and qualitative feedback from programme participants. Analysis proceeded via the constant comparison method. A model was generated to visually present key findings. Twenty-three in-depth interviews were conducted representing 18 different programmes. Eight programmes were observed directly, 48 programme documents were reviewed, and data from 1812 programme participants were reviewed. The analysis led to a four-stage process model for implementing successful antistigma programmes targeting healthcare providers, informed by the basic social process 'targeting the roots of healthcare provider stigma'. The process model developed through this research may function as a tool to help guide the development and implementation of antistigma programmes in healthcare contexts. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

All-optical central-frequency-programmable and bandwidth-tailorable radar

PubMed Central

Zou, Weiwen; Zhang, Hao; Long, Xin; Zhang, Siteng; Cui, Yuanjun; Chen, Jianping

2016-01-01

Radar has been widely used for military, security, and rescue purposes, and modern radar should be reconfigurable at multi-bands and have programmable central frequencies and considerable bandwidth agility. Microwave photonics or photonics-assisted radio-frequency technology is a unique solution to providing such capabilities. Here, we demonstrate an all-optical central-frequency-programmable and bandwidth-tailorable radar architecture that provides a coherent system and utilizes one mode-locked laser for both signal generation and reception. Heterodyning of two individually filtered optical pulses that are pre-chirped via wavelength-to-time mapping generates a wideband linearly chirped radar signal. The working bands can be flexibly tailored with the desired bandwidth at a user-preferred carrier frequency. Radar echoes are first modulated onto the pre-chirped optical pulse, which is also used for signal generation, and then stretched in time or compressed in frequency several fold based on the time-stretch principle. Thus, digitization is facilitated without loss of detection ability. We believe that our results demonstrate an innovative radar architecture with an ultra-high-range resolution. PMID:26795596

Active modulation of laser coded systems using near infrared video projection system based on digital micromirror device (DMD)

NASA Astrophysics Data System (ADS)

Khalifa, Aly A.; Aly, Hussein A.; El-Sherif, Ashraf F.

2016-02-01

Near infrared (NIR) dynamic scene projection systems are used to perform hardware in-the-loop (HWIL) testing of a unit under test operating in the NIR band. The common and complex requirement of a class of these units is a dynamic scene that is spatio-temporal variant. In this paper we apply and investigate active external modulation of NIR laser in different ranges of temporal frequencies. We use digital micromirror devices (DMDs) integrated as the core of a NIR projection system to generate these dynamic scenes. We deploy the spatial pattern to the DMD controller to simultaneously yield the required amplitude by pulse width modulation (PWM) of the mirror elements as well as the spatio-temporal pattern. Desired modulation and coding of high stable, high power visible (Red laser at 640 nm) and NIR (Diode laser at 976 nm) using the combination of different optical masks based on DMD were achieved. These spatial versatile active coding strategies for both low and high frequencies in the range of kHz for irradiance of different targets were generated by our system and recorded using VIS-NIR fast cameras. The temporally-modulated laser pulse traces were measured using array of fast response photodetectors. Finally using a high resolution spectrometer, we evaluated the NIR dynamic scene projection system response in terms of preserving the wavelength and band spread of the NIR source after projection.

Nutrition advocacy and national development: the PROFILES programme and its application.

PubMed

Burkhalter, B R; Abel, E; Aguayo, V; Diene, S M; Parlato, M B; Ross, J S

1999-01-01

Investment in nutritional programmes can contribute to economic growth and is cost-effective in improving child survival and development. In order to communicate this to decision-makers, the PROFILES nutrition advocacy and policy development programme was applied in certain developing countries. Effective advocacy is necessary to generate financial and political support for scaling up from small pilot projects and maintaining successful national programmes. The programme uses scientific knowledge to estimate development indicators such as mortality, morbidity, fertility, school performance and labour productivity from the size and nutritional condition of populations. Changes in nutritional condition are estimated from the costs, coverage and effectiveness of proposed programmes. In Bangladesh this approach helped to gain approval and funding for a major nutrition programme. PROFILES helped to promote the nutrition component of an early childhood development programme in the Philippines, and to make nutrition a top priority in Ghana's new national child survival strategy. The application of PROFILES in these and other countries has been supported by the United States Agency for International Development, the United Nations Children's Fund, the World Bank, the Asian Development Bank, the Micronutrient Initiative and other bodies.

A Field Programmable Gate Array-Based Reconfigurable Smart-Sensor Network for Wireless Monitoring of New Generation Computer Numerically Controlled Machines

PubMed Central

Moreno-Tapia, Sandra Veronica; Vera-Salas, Luis Alberto; Osornio-Rios, Roque Alfredo; Dominguez-Gonzalez, Aurelio; Stiharu, Ion; de Jesus Romero-Troncoso, Rene

2010-01-01

Computer numerically controlled (CNC) machines have evolved to adapt to increasing technological and industrial requirements. To cover these needs, new generation machines have to perform monitoring strategies by incorporating multiple sensors. Since in most of applications the online Processing of the variables is essential, the use of smart sensors is necessary. The contribution of this work is the development of a wireless network platform of reconfigurable smart sensors for CNC machine applications complying with the measurement requirements of new generation CNC machines. Four different smart sensors are put under test in the network and their corresponding signal processing techniques are implemented in a Field Programmable Gate Array (FPGA)-based sensor node. PMID:22163602

A field programmable gate array-based reconfigurable smart-sensor network for wireless monitoring of new generation computer numerically controlled machines.

PubMed

Moreno-Tapia, Sandra Veronica; Vera-Salas, Luis Alberto; Osornio-Rios, Roque Alfredo; Dominguez-Gonzalez, Aurelio; Stiharu, Ion; Romero-Troncoso, Rene de Jesus

2010-01-01

Computer numerically controlled (CNC) machines have evolved to adapt to increasing technological and industrial requirements. To cover these needs, new generation machines have to perform monitoring strategies by incorporating multiple sensors. Since in most of applications the online Processing of the variables is essential, the use of smart sensors is necessary. The contribution of this work is the development of a wireless network platform of reconfigurable smart sensors for CNC machine applications complying with the measurement requirements of new generation CNC machines. Four different smart sensors are put under test in the network and their corresponding signal processing techniques are implemented in a Field Programmable Gate Array (FPGA)-based sensor node.

Immunological evaluation of four arc welders exposed to fumes from ignited polyurethane (isocyanate) foam: antibodies and immune profiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broughton, A.; Thrasher, J.D.; Gard, Z.

1988-01-01

Four arc welders having a flu-like illness with multiple health complaints following an exposure to high concentrations of isocyanate fumes from ignited polyurethane foam underwent immunological tests as follows: ELISA antibody assays, activated lymphocyte profiles, and lymphocyte blastogenesis. ELISA procedures revealed the presence of antibodies to hexamethylene diisocyanate (HDI) and formaldehyde (F) conjugated to human serum albumin (HDI-SA and F-SA). The results from the activated lymphocyte profiles showed deviations from the norm as follows: three welders had elevated helper/suppressor (H/S) ratios; all four had elevated percentages of Tal positive cells; two had decreases in B cells; and one had lowmore » total white cell and lymphocyte counts. In contrast, the percentage and absolute numbers of ILS receptor cells were normal in the four subjects. T cell blastogenesis to PHA, Con A and PWM resulted in the following: T-cells from one subject responded normally; in another, a high response (212% of controls) to PHA occurred with normal mitogenesis to Con A and PWM. In the remaining two welders, the T cells responded abnormally low (50 to 75% of controls) to the three mitogens. In conclusion, the existence of IgG antibodies to HDI-SA and F-SA, the altered activated immune profiles, the elevated Tal cells, and the abnormal blastogenesis are interpreted as being linked with the episode of HDI and F exposure and the subsequent flu-like illness of the four welders.« less

Development of microheaters for gas sensor with an AT-Mega 8535 temperature controller using a PWM (pulse width modulation) method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Megayanti, Meti; Panatarani, Camellia; Joni, I. Made, E-mail: imadejoni@phys.unpad.ac.id

Microheater is the main component in gas sensor characterized by their sensitivity, selectivity, and time response of gas sensor which is depend on the microheater temperature stability. A Cu microheater was developed and utilized AT-Mega 8535 controller using a PWM (pulse width modulation) method. This control system is interfaced to the PC to observe the real time temperature response of the microheater. Three initial resistance (R0) variations of microheater were developed in an open loop control system. The power characteristic of designed microheater depends on the specified microheater initial resistance. The smaller R0, the less power required to reach amore » temperature setting value. The developed microheater was designed to reach a temperature setting value of 250°C having resistance 0.531 Ω for 1.979 Watt and 0.265 Ω for 1.072 Watt respectively. The results of the investigation on the control performances shows microheater-control system achieved operating temperature up to 250°C. The response of the temperature control shows smallest R0 resulted in a high stability with short settling time, short delay time and small ripple for temperature setting values higher than 150°C. The obtained error of microheater temperature with R0 = 0.265 is 8.596 %. It is concluded that the developed microheater can be utilized as a component of a gas sensor.« less

Note: The design of thin gap chamber simulation signal source based on field programmable gate array.

PubMed

Hu, Kun; Lu, Houbing; Wang, Xu; Li, Feng; Liang, Futian; Jin, Ge

2015-01-01

The Thin Gap Chamber (TGC) is an important part of ATLAS detector and LHC accelerator. Targeting the feature of the output signal of TGC detector, we have designed a simulation signal source. The core of the design is based on field programmable gate array, randomly outputting 256-channel simulation signals. The signal is generated by true random number generator. The source of randomness originates from the timing jitter in ring oscillators. The experimental results show that the random number is uniform in histogram, and the whole system has high reliability.

Note: The design of thin gap chamber simulation signal source based on field programmable gate array

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Kun; Wang, Xu; Li, Feng

The Thin Gap Chamber (TGC) is an important part of ATLAS detector and LHC accelerator. Targeting the feature of the output signal of TGC detector, we have designed a simulation signal source. The core of the design is based on field programmable gate array, randomly outputting 256-channel simulation signals. The signal is generated by true random number generator. The source of randomness originates from the timing jitter in ring oscillators. The experimental results show that the random number is uniform in histogram, and the whole system has high reliability.

System and method for programmable bank selection for banked memory subsystems

DOEpatents

Blumrich, Matthias A.; Chen, Dong; Gara, Alan G.; Giampapa, Mark E.; Hoenicke, Dirk; Ohmacht, Martin; Salapura, Valentina; Sugavanam, Krishnan

2010-09-07

A programmable memory system and method for enabling one or more processor devices access to shared memory in a computing environment, the shared memory including one or more memory storage structures having addressable locations for storing data. The system comprises: one or more first logic devices associated with a respective one or more processor devices, each first logic device for receiving physical memory address signals and programmable for generating a respective memory storage structure select signal upon receipt of pre-determined address bit values at selected physical memory address bit locations; and, a second logic device responsive to each of the respective select signal for generating an address signal used for selecting a memory storage structure for processor access. The system thus enables each processor device of a computing environment memory storage access distributed across the one or more memory storage structures.

Synthesis and cell-free cloning of DNA libraries using programmable microfluidics

PubMed Central

Yehezkel, Tuval Ben; Rival, Arnaud; Raz, Ofir; Cohen, Rafael; Marx, Zipora; Camara, Miguel; Dubern, Jean-Frédéric; Koch, Birgit; Heeb, Stephan; Krasnogor, Natalio; Delattre, Cyril; Shapiro, Ehud

2016-01-01

Microfluidics may revolutionize our ability to write synthetic DNA by addressing several fundamental limitations associated with generating novel genetic constructs. Here we report the first de novo synthesis and cell-free cloning of custom DNA libraries in sub-microliter reaction droplets using programmable digital microfluidics. Specifically, we developed Programmable Order Polymerization (POP), Microfluidic Combinatorial Assembly of DNA (M-CAD) and Microfluidic In-vitro Cloning (MIC) and applied them to de novo synthesis, combinatorial assembly and cell-free cloning of genes, respectively. Proof-of-concept for these methods was demonstrated by programming an autonomous microfluidic system to construct and clone libraries of yeast ribosome binding sites and bacterial Azurine, which were then retrieved in individual droplets and validated. The ability to rapidly and robustly generate designer DNA molecules in an autonomous manner should have wide application in biological research and development. PMID:26481354

A programmable microfluidic static droplet array for droplet generation, transportation, fusion, storage, and retrieval.

PubMed

Jin, Si Hyung; Jeong, Heon-Ho; Lee, Byungjin; Lee, Sung Sik; Lee, Chang-Soo

2015-01-01

We present a programmable microfluidic static droplet array (SDA) device that can perform user-defined multistep combinatorial protocols. It combines the passive storage of aqueous droplets without any external control with integrated microvalves for discrete sample dispensing and dispersion-free unit operation. The addressable picoliter-volume reaction is systematically achieved by consecutively merging programmable sequences of reagent droplets. The SDA device is remarkably reusable and able to perform identical enzyme kinetic experiments at least 30 times via automated cross-contamination-free removal of droplets from individual hydrodynamic traps. Taking all these features together, this programmable and reusable universal SDA device will be a general microfluidic platform that can be reprogrammed for multiple applications.

Effects of Self-Efficacy Training Programmes on Adolescents' Sexual Risk-Taking Behaviour in Oyo State, Nigeria

ERIC Educational Resources Information Center

Musa, Titilayo Monsurat

2017-01-01

Adolescents' sexual risk-taking behavioural issues have generated concerns among parents, teachers and social workers. The study examined the effects of self-efficacy training programmes on adolescents' sexual risk-taking behaviour and also investigated whether socio-economic status and gender would moderate the effects of treatment on sexual…

Lichen elements as pollution indicators: evaluation of methods for large monitoring programmes

Treesearch

Susan Will-Wolf; Sarah Jovan; Michael C. Amacher

2017-01-01

Lichen element content is a reliable indicator for relative air pollution load in research and monitoring programmes requiring both efficiency and representation of many sites. We tested the value of costly rigorous field and handling protocols for sample element analysis using five lichen species. No relaxation of rigour was supported; four relaxed protocols generated...

The Politics of the Academies Programme: Natality and Pluralism in Education Policy-Making

ERIC Educational Resources Information Center

Gunter, Helen M.; McGinity, Ruth

2014-01-01

Our investigations into the politics of the Academies Programme in England have generated thinking that draws on data about the conversion process from two projects. We engage with an early City Academy that replaced two "failing" schools, and a recent Academy that replaced a "successful" high school. We deploy Hannah Arendt's…

Mentoring the Next Researcher Generation: Reflections on Three Years of Building VET Research Capacity and Infrastructure

ERIC Educational Resources Information Center

Barratt-Pugh, Llandis Gareth

2012-01-01

During 2008-2011, the National Centre for Vocational Education Research (NCVER) funded a programme to build Australian VET research capacity and rejuvenate what has been seen as the existing "greying" researcher pool. This paper is a reflective narrative about experiences of constructing the programme with a specific focus on the…

Programmable random interval generator

NASA Technical Reports Server (NTRS)

Lindsey, R. S., Jr.

1973-01-01

Random pulse generator can supply constant-amplitude randomly distributed pulses with average rate ranging from a few counts per second to more than one million counts per second. Generator requires no high-voltage power supply or any special thermal cooling apparatus. Device is uniquely versatile and provides wide dynamic range of operation.

Technical data on new engineering products

NASA Astrophysics Data System (ADS)

1985-02-01

New grades of permanently magnetic materials; automatic digital radiolocator; bench winder; analog induction gauge; programmable pulse generator; portable defibrillators; pipe welders; two-component electromagnetic log; sulphur content analyzer; peristaltic pumps; function generators; welding manipulator; and tonsiometer are described.

Reduction in antipredator response detected between first and second generations of endangered juvenile Atlantic salmon Salmo salar in a captive breeding and rearing programme.

PubMed

de Mestral, L G; Herbinger, C M

2013-11-01

Behaviour trials determining antipredator response were conducted on first and second generation juveniles from a captive breeding and rearing programme for endangered Inner Bay of Fundy Atlantic salmon Salmo salar. Second generation captive fry displayed significantly higher levels of risk-taking behaviour before and after exposure to a simulated avian predator. Because the first and second generation fry were reared under the same environmental conditions and differed only in the number of generations spent in captivity, these results suggest that rapid genetic changes, possibly due to domestication selection, may have occurred. Antipredator response was also assessed in fully wild and highly domesticated experimental groups: wild fry displayed the greatest antipredator response and domesticated fry displayed the highest levels of risk-taking behaviour. These results add to the growing evidence documenting rapid genetic change in response to rearing in a captive environment. © 2013 The Fisheries Society of the British Isles.

3T magnetic resonance imaging testing of externally programmable shunt valves

PubMed Central

Zabramski, Joseph M.; Preul, Mark C.; Debbins, Josef; McCusker, Daniel J.

2012-01-01

Background: Exposure of externally programmable shunt-valves (EPS-valves) to magnetic resonance imaging (MRI) may lead to unexpected changes in shunt settings, or affect the ability to reprogram the valve. We undertook this study to examine the effect of exposure to a 3T MRI on a group of widely used EPS-valves. Methods: Evaluations were performed on first generation EPS-valves (those without a locking mechanism to prevent changes in shunt settings by external magnets other than the programmer) and second generation EPS-valves (those with a locking mechanisms). Fifteen new shunt-valves were divided into five groups of three identical valves each, and then exposed to a series of six simulated MRI scans. After each of the exposures, the valves were evaluated to determine if the valve settings had changed, and whether the valves could be reprogrammed. The study produced 18 evaluations for each line of shunt-valves. Results: Exposure of the first generation EPS-valves to a 3T magnetic field resulted in frequent changes in the valve settings; however, all valves retained their ability to be reprogrammed. Repeated exposure of the second generation EPS-valves has no effect on shunt valve settings, and all valves retained their ability to be interrogated and reprogrammed. Conclusions: Second generation EPS-valves with locking mechanisms can be safely exposed to repeated 3T MRI systems, without evidence that shunt settings will change. The exposure of the first generation EPS-valves to 3T MRI results in frequent changes in shunt settings that necessitate re-evaluation soon after MRI to avoid complications. PMID:22937481

Cost-effectiveness of a disease management programme for secondary prevention of coronary heart disease and heart failure in primary care.

PubMed

Turner, D A; Paul, S; Stone, M A; Juarez-Garcia, A; Squire, I; Khunti, K

2008-12-01

To determine if a disease management programme for patients with coronary heart disease and heart failure represents an efficient use of health services resources. We carried out an economic evaluation alongside a cluster randomised control trial of 1163 patients with coronary heart disease and chronic heart failure in 20 primary care practices in the United Kingdom. Practices were randomised to either a control group, where patients received standard general practice care, or an intervention group where patients had access to a specialist nurse-led disease management programme. We estimated costs in both groups for coronary heart disease-related resource use. The main outcome measure used in the economic evaluation was quality adjusted life years (QALY) measured using the EuroQol. The disease management programme was associated with an increase in the QALY measured of 0.03 per year and an increase in the total NHS costs of 425 pounds (540 euros), of this only 83 pounds was directly associated with the provision of the nurse clinics. The clinics generated additional QALY at an incremental cost of 13 pounds 158 per QALY compared to the control group. The use of a nurse-led disease management programme is associated with increased costs in other coronary heart disease-related services as well as for the costs of the clinics. They are also associated with improvements in health. Even in the short term these disease management programmes may represent a cost-effective service, as additional QALY are generated at an acceptable extra cost.

Nutrition advocacy and national development: the PROFILES programme and its application.

PubMed Central

Burkhalter, B. R.; Abel, E.; Aguayo, V.; Diene, S. M.; Parlato, M. B.; Ross, J. S.

1999-01-01

Investment in nutritional programmes can contribute to economic growth and is cost-effective in improving child survival and development. In order to communicate this to decision-makers, the PROFILES nutrition advocacy and policy development programme was applied in certain developing countries. Effective advocacy is necessary to generate financial and political support for scaling up from small pilot projects and maintaining successful national programmes. The programme uses scientific knowledge to estimate development indicators such as mortality, morbidity, fertility, school performance and labour productivity from the size and nutritional condition of populations. Changes in nutritional condition are estimated from the costs, coverage and effectiveness of proposed programmes. In Bangladesh this approach helped to gain approval and funding for a major nutrition programme. PROFILES helped to promote the nutrition component of an early childhood development programme in the Philippines, and to make nutrition a top priority in Ghana's new national child survival strategy. The application of PROFILES in these and other countries has been supported by the United States Agency for International Development, the United Nations Children's Fund, the World Bank, the Asian Development Bank, the Micronutrient Initiative and other bodies. PMID:10361758

Politics of Leadership and Implementation of Educational Policies and Programmes of Tertiary Institutions in Cross River State, Nigeria

ERIC Educational Resources Information Center

Ekpiken, W. E.; Ifere, Francis O.

2015-01-01

This paper examines issues of politics of leadership and implementation of Educational policies and programmes of tertiary institutions in Cross River State with a view to determine the problems are situated and suggest the way forward. It examines the concept of politics of education, concept of leadership, meaning of planning and generation of…

Compact field programmable gate array-based pulse-sequencer and radio-frequency generator for experiments with trapped atoms.

PubMed

Pruttivarasin, Thaned; Katori, Hidetoshi

2015-11-01

We present a compact field-programmable gate array (FPGA) based pulse sequencer and radio-frequency (RF) generator suitable for experiments with cold trapped ions and atoms. The unit is capable of outputting a pulse sequence with at least 32 transistor-transistor logic (TTL) channels with a timing resolution of 40 ns and contains a built-in 100 MHz frequency counter for counting electrical pulses from a photo-multiplier tube. There are 16 independent direct-digital-synthesizers RF sources with fast (rise-time of ∼60 ns) amplitude switching and sub-mHz frequency tuning from 0 to 800 MHz.

CGAT: a model for immersive personalized training in computational genomics

PubMed Central

Sims, David; Ponting, Chris P.

2016-01-01

How should the next generation of genomics scientists be trained while simultaneously pursuing high quality and diverse research? CGAT, the Computational Genomics Analysis and Training programme, was set up in 2010 by the UK Medical Research Council to complement its investment in next-generation sequencing capacity. CGAT was conceived around the twin goals of training future leaders in genome biology and medicine, and providing much needed capacity to UK science for analysing genome scale data sets. Here we outline the training programme employed by CGAT and describe how it dovetails with collaborative research projects to launch scientists on the road towards independent research careers in genomics. PMID:25981124

MOEMs-based new functionalities for future instrumentation in space

NASA Astrophysics Data System (ADS)

Zamkotsian, Frédéric; Liotard, Arnaud; Viard, Thierry; Costes, Vincent; Hébert, Philippe-Jean; Hinglais, Emmanuel; Villenave, Michel

2017-11-01

Micro-Opto-Electro-Mechanical Systems (MOEMS) could be key components in future generation of space instruments. In Earth Observation, Universe Observation and Planet Exploration, scientific return of the instruments must be optimized in future missions. MOEMS devices are based on the mature micro-electronics technology and in addition to their compactness, scalability, and specific task customization, they could generate new functions not available with current technologies. CNES has initiated a study with LAM and TAS for listing the new functions associated with several types of MEMS (programmable slits, programmable micro-diffraction gratings, micro-deformable mirrors). Instrumental applications are then derived and promising concepts are described.

Compact field programmable gate array-based pulse-sequencer and radio-frequency generator for experiments with trapped atoms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pruttivarasin, Thaned, E-mail: thaned.pruttivarasin@riken.jp; Katori, Hidetoshi; Innovative Space-Time Project, ERATO, JST, Bunkyo-ku, Tokyo 113-8656

We present a compact field-programmable gate array (FPGA) based pulse sequencer and radio-frequency (RF) generator suitable for experiments with cold trapped ions and atoms. The unit is capable of outputting a pulse sequence with at least 32 transistor-transistor logic (TTL) channels with a timing resolution of 40 ns and contains a built-in 100 MHz frequency counter for counting electrical pulses from a photo-multiplier tube. There are 16 independent direct-digital-synthesizers RF sources with fast (rise-time of ∼60 ns) amplitude switching and sub-mHz frequency tuning from 0 to 800 MHz.

Synthetic biology in mammalian cells: Next generation research tools and therapeutics

PubMed Central

Lienert, Florian; Lohmueller, Jason J; Garg, Abhishek; Silver, Pamela A

2014-01-01

Recent progress in DNA manipulation and gene circuit engineering has greatly improved our ability to programme and probe mammalian cell behaviour. These advances have led to a new generation of synthetic biology research tools and potential therapeutic applications. Programmable DNA-binding domains and RNA regulators are leading to unprecedented control of gene expression and elucidation of gene function. Rebuilding complex biological circuits such as T cell receptor signalling in isolation from their natural context has deepened our understanding of network motifs and signalling pathways. Synthetic biology is also leading to innovative therapeutic interventions based on cell-based therapies, protein drugs, vaccines and gene therapies. PMID:24434884

Single-chip pulse programmer for magnetic resonance imaging using a 32-bit microcontroller.

PubMed

Handa, Shinya; Domalain, Thierry; Kose, Katsumi

2007-08-01

A magnetic resonance imaging (MRI) pulse programmer has been developed using a single-chip microcontroller (ADmicroC7026). The microcontroller includes all the components required for the MRI pulse programmer: a 32-bit RISC CPU core, 62 kbytes of flash memory, 8 kbytes of SRAM, two 32-bit timers, four 12-bit DA converters, and 40 bits of general purpose I/O. An evaluation board for the microcontroller was connected to a host personal computer (PC), an MRI transceiver, and a gradient driver using interface circuitry. Target (embedded) and host PC programs were developed to enable MRI pulse sequence generation by the microcontroller. The pulse programmer achieved a (nominal) time resolution of approximately 100 ns and a minimum time delay between successive events of approximately 9 micros. Imaging experiments using the pulse programmer demonstrated the effectiveness of our approach.

Single-chip pulse programmer for magnetic resonance imaging using a 32-bit microcontroller

NASA Astrophysics Data System (ADS)

Handa, Shinya; Domalain, Thierry; Kose, Katsumi

2007-08-01

A magnetic resonance imaging (MRI) pulse programmer has been developed using a single-chip microcontroller (ADμC7026). The microcontroller includes all the components required for the MRI pulse programmer: a 32-bit RISC CPU core, 62kbytes of flash memory, 8kbytes of SRAM, two 32-bit timers, four 12-bit DA converters, and 40bits of general purpose I/O. An evaluation board for the microcontroller was connected to a host personal computer (PC), an MRI transceiver, and a gradient driver using interface circuitry. Target (embedded) and host PC programs were developed to enable MRI pulse sequence generation by the microcontroller. The pulse programmer achieved a (nominal) time resolution of approximately 100ns and a minimum time delay between successive events of approximately 9μs. Imaging experiments using the pulse programmer demonstrated the effectiveness of our approach.

Programmable Pulse Generator

NASA Technical Reports Server (NTRS)

Rhim, W. K.; Dart, J. A.

1982-01-01

New pulse generator programmed to produce pulses from several ports at different pulse lengths and intervals and virtually any combination and sequence. Unit contains a 256-word-by-16-bit memory loaded with instructions either manually or by computer. Once loaded, unit operates independently of computer.

MOEMs devices designed and tested for future astronomical instrumentation in space

NASA Astrophysics Data System (ADS)

Zamkotsian, Frédéric; Lanzoni, Patrick; Waldis, Severin; Noell, Wilfried; Conedera, Veronique; Fabre, Norbert; Viard, Thierry; Buisset, Christophe

2017-11-01

Next generation of astronomical instrumentation for space telescopes requires Micro-Opto-Electro- Mechanical Systems (MOEMS) with remote control capability and cryogenic operation. MOEMS devices have the capability to tailor the incoming light in terms of intensity and object selection with programmable slit masks, in terms of phase and wavefront control with micro-deformable mirrors, and finally in terms of spectrum with programmable diffraction gratings. Applications are multi-object spectroscopy (MOS), wavefront correction and programmable spectrographs. We are engaged since several years in the design, realization and characterization of MOEMS devices suited for astronomical instrumentation.

Fuzz Testing of Industrial Network Protocols in Programmable Logic Controllers

DTIC Science & Technology

2017-12-01

PLCs) are vital components in these cyber-physical systems. The industrial network protocols used to communicate between nodes in a control network...AB/RA) MicroLogix 1100 PLC through its implementation of EtherNet/IP, Common Industrial Protocol (CIP), and Programmable Controller Communication ...Commands (PCCC) communication protocols. This research also examines whether cross-generational vulnerabilities exist in the more advanced AB/RA

Analysing Instructors' View Regarding the Efficiency of the Turkish History Subjects Presented in Turkey Social Studies Textbooks

ERIC Educational Resources Information Center

Seker, Mustafa; Ilhan, Genç Osman

2015-01-01

Just like it is the reflex of each nation to teach its own history to the next generations, it is essential that our country is also able to identify the sufficiency level of the Turkish history within the framework of developing a programme. Through this study, the parallelism between the social studies teaching programme within the education…

Ultra-high resolution AMOLED

NASA Astrophysics Data System (ADS)

Wacyk, Ihor; Prache, Olivier; Ghosh, Amal

2011-06-01

AMOLED microdisplays continue to show improvement in resolution and optical performance, enhancing their appeal for a broad range of near-eye applications such as night vision, simulation and training, situational awareness, augmented reality, medical imaging, and mobile video entertainment and gaming. eMagin's latest development of an HDTV+ resolution technology integrates an OLED pixel of 3.2 × 9.6 microns in size on a 0.18 micron CMOS backplane to deliver significant new functionality as well as the capability to implement a 1920×1200 microdisplay in a 0.86" diagonal area. In addition to the conventional matrix addressing circuitry, the HDTV+ display includes a very lowpower, low-voltage-differential-signaling (LVDS) serialized interface to minimize cable and connector size as well as electromagnetic emissions (EMI), an on-chip set of look-up-tables for digital gamma correction, and a novel pulsewidth- modulation (PWM) scheme that together with the standard analog control provides a total dimming range of 0.05cd/m2 to 2000cd/m2 in the monochrome version. The PWM function also enables an impulse drive mode of operation that significantly reduces motion artifacts in high speed scene changes. An internal 10-bit DAC ensures that a full 256 gamma-corrected gray levels are available across the entire dimming range, resulting in a measured dynamic range exceeding 20-bits. This device has been successfully tested for operation at frame rates ranging from 30Hz up to 85Hz. This paper describes the operational features and detailed optical and electrical test results for the new AMOLED WUXGA resolution microdisplay.

beta2-Microglobulin production by highly purified human T and B lymphocytes in cell culture stimulated with various mitogens.

PubMed

Kin, K; Kasahara, T; Itoh, Y; Sakurabayashi, I; Kawai, T; Morita, M

1979-01-01

This study attempts to evaluate beta2-microglobulin production by highly purified (greater than 98%) peripheral and tonsil T and B lymphocytes cultured with various mitogens. beta2-Microglobulin was measured by the radioimmunoassay method. It was found that PHA and Con A markedly stimulated beta2-microglobulin production in cultures of T but not B lymphocytes. B lymphocytes were greatly activated, on the other hand, by Staphylococcus aureau Cowan I organisms cSpA), though the level of beta2-microglobulin production was less than that observed in PHA- and Con A-stimulated T lymphocytes. PWM only slightly increased beta2-microglobulin production of T lymphocytes, although the incorporation of [3H]-thymidine was highly enhanced. The highest level of beta2-microglobulin obtained with PHA or Con A was observed when the T/B lymphocyte ratio was between 90/10 and 80/20. These results lead to the conclusion that: (1) SpA is a specific mitogen for B lymphocytes, and its mitogenicity is independent of the presence of T lymphocytes, while PHA, Con A, and PWM are ineffective as stimulants of B lymphocytes; (2) the beta2-microglobulin producing ability of B lymphocytes is less than that of T lymphocytes, even when the lymphocytes are markedly activated; (3) the beta2-microglobulin production and DNA synthesis by T lymphocytes is markedly enhanced by the helper effect of B lymphocytes; (4) the level of beta2-microglobulin production reflects lymphocyte activation, especially in T lymphocytes stimulated with PHA or Con A.

Reliability assessment and improvement for a fast corrector power supply in TPS

NASA Astrophysics Data System (ADS)

Liu, Kuo-Bin; Liu, Chen-Yao; Wang, Bao-Sheng; Wong, Yong Seng

2018-07-01

Fast Orbit Feedback System (FOFB) can be installed in a synchrotron light source to eliminate undesired disturbances and to improve the stability of beam orbit. The design and implementation of an accurate and reliable Fast Corrector Power Supply (FCPS) is essential to realize the effectiveness and availability of the FOFB. A reliability assessment for the FCPSs in the FOFB of Taiwan Photon Source (TPS) considering MOSFETs' temperatures is represented in this paper. The FCPS is composed of a full-bridge topology and a low-pass filter. A Hybrid Pulse Width Modulation (HPWM) requiring two MOSFETs in the full-bridge circuit to be operated at high frequency and the other two be operated at the output frequency is adopted to control the implemented FCPS. Due the characteristic of HPWM, the conduction loss and switching loss of each MOSFET in the FCPS is not same. Two of the MOSFETs in the full-bridge circuit will suffer higher temperatures and therefore the circuit reliability of FCPS is reduced. A Modified PWM Scheme (MPWMS) designed to average MOSFETs' temperatures and to improve circuit reliability is proposed in this paper. Experimental results measure the MOSFETs' temperatures of FCPS controlled by the HPWM and the proposed MPWMS. The reliability indices under different PWM controls are then assessed. From the experimental results, it can be observed that the reliability of FCPS using the proposed MPWMS can be improved because the MOSFETs' temperatures are closer. Since the reliability of FCPS can be enhanced, the availability of FOFB can also be improved.

Impact of an educational program on knowledge and practice of health care staff toward pharmaceutical waste management in Gaza, Palestine.

PubMed

Tabash, Mohammed I; Hussein, Rim A; Mahmoud, Aleya H; El-Borgy, Mohamed D; Abu-Hamad, Bassam A

2016-04-01

In health care facilities, pharmaceutical waste is generally discharged down the drain or sent to landfill. Poor knowledge about their potential downstream impacts may be a primary factor for improper disposal behavior. The objective of this study was to determine the impact of an intervention program on knowledge and practice of health care staff regarding pharmaceutical waste management. The study was designed as a pre/posttest intervention study. Total sample size was 530 in the pre-intervention phase, and then a subsample of 69 individuals was selected for the intervention and the post-intervention phases. Paired-sample t test was used to assess the difference between pretest and follow-up test results. A statistically significant improvement in knowledge and practice was achieved (P<0.001). Poor knowledge and poor practice levels (scores<50%) were found to improve to satisfactory levels (scores≥75%). Therefore, educational programs could be considered as an effective tool for changing health care staff practice in pharmaceutical waste management. In health care facilities, pharmaceutical waste is generally discharged down the drain or sent to landfill. A lack of knowledge about the potential impacts of this type of waste may be a leading factor in improper disposal behavior. Following an educational program, statistically significant improvement in knowledge and practice of health care staff as regards to pharmaceutical waste management (PWM) was achieved. It is thus recommended that authorities implement training-of-trainers (TOT) programs to educate health care staff on PWM and organize refreshment workshops regularly.

Expression of a germline human kappa chain-associated cross-reactive idiotype after in vitro and in vivo infection with Epstein-Barr virus.

PubMed

Silverman, G J; Carson, D A; Patrick, K; Vaughan, J H; Fong, S

1987-06-01

The mouse monoclonal antibody 17.109 recognizes a cross-reactive idiotype (CRI) associated with kappa IIIb light chains of human IgM-rheumatoid factor (RF) paraproteins. The 17.109 idiotypic determinant is encoded by one or a group of closely related V kappa genes. The association of the idiotype with IgM- and IgA-rheumatoid factors in certain autoimmune diseases necessitates an understanding of how human B lymphocytes can be induced to express the idiotype. To investigate the cellular expression of the 17.109 CRI, peripheral blood lymphocytes from normal donors were stimulated in vitro with Epstein-Barr virus (EBV) and pokeweed mitogen (PWM). EBV induced greater expression of IgM-associated 17.109 CRI than did PWM. The 17.109 CRI was preferentially associated with IgM rather than with IgG. In vivo EBV infection was studied in college students with infectious mononucleosis and displayed similar elevation of IgM-associated 17.109 CRI in sera obtained at presentation of clinical illness. Later, IgM levels declined while IgG-associated 17.109 CRI rose. The 17.109 idiotype was unrelated to antibodies against the Epstein-Barr virus nuclear antigen and the viral capsid antigen and was probably due to generalized activation of early B cells. These observations support the hypothesis that the 17.109 CRI is expressed by in vitro and in vivo EBV-infected cells. The 17.109 idiotype identifies a highly conserved V kappa gene product, which is expressed preferentially after EBV infection, but not exclusively with RF autoantibodies.

Programmable DNA-Guided Artificial Restriction Enzymes.

PubMed

Enghiad, Behnam; Zhao, Huimin

2017-05-19

Restriction enzymes are essential tools for recombinant DNA technology that have revolutionized modern biological research. However, they have limited sequence specificity and availability. Here we report a Pyrococcus furiosus Argonaute (PfAgo) based platform for generating artificial restriction enzymes (AREs) capable of recognizing and cleaving DNA sequences at virtually any arbitrary site and generating defined sticky ends of varying length. Short DNA guides are used to direct PfAgo to target sites for cleavage at high temperatures (>87 °C) followed by reannealing of the cleaved single stranded DNAs. We used this platform to generate over 18 AREs for DNA fingerprinting and molecular cloning of PCR-amplified or genomic DNAs. These AREs work as efficiently as their naturally occurring counterparts, and some of them even do not have any naturally occurring counterparts, demonstrating easy programmability, generality, versatility, and high efficiency for this new technology.

Clock jitter generator with picoseconds resolution

NASA Astrophysics Data System (ADS)

Jovanović, Goran; Stojčev, Mile; Nikolić, Tatjana

2013-06-01

The clock is one of the most critical signals in any synchronous system. As CMOS technology has scaled, supply voltages have dropped chip power consumption has increased and the effects of jitter due to clock frequency increase have become critical and jitter budget has become tighter. This article describes design and development of low-cost mixed-signal programmable jitter generator with high resolution. The digital technique is used for coarse-grain and an analogue technique for fine-grain clock phase shifting. Its structure allows injection of various random and deterministic jitter components in a controllable and programmable fashion. Each jitter component can be switched on or off. The jitter generator can be used in jitter tolerance test and jitter transfer function measurement of high-speed synchronous digital circuits. At operating system clock frequency of 220 MHz, a jitter with 4 ps resolution can be injected.

An Application of Reverse Engineering to Automatic Item Generation: A Proof of Concept Using Automatically Generated Figures

ERIC Educational Resources Information Center

Lorié, William A.

2013-01-01

A reverse engineering approach to automatic item generation (AIG) was applied to a figure-based publicly released test item from the Organisation for Economic Cooperation and Development (OECD) Programme for International Student Assessment (PISA) mathematical literacy cognitive instrument as part of a proof of concept. The author created an item…

Design considerations and tradeoffs for passive RFID tags

NASA Astrophysics Data System (ADS)

Hussien, Faisal A.; Turker, Didem Z.; Srinivasan, Rangakrishnan; Mobarak, Mohamed S.; Cortes, Fernando P.; Sanchez-Sinencio, Edgar

2005-06-01

Radio Frequency Identification (RFID) systems are widely used in a variety of tracking, security and tagging applications. Their operation in non line-of-sight environments makes them superior over similar devices such as barcode and infrared tags. RFID systems span a wide range of applications: medical history storage, dental prosthesis tracking, oil drilling pipe and concrete stress monitoring, toll ways services, animal tracking applications, etc. Passive RFID tags generate their power from the incoming signal; therefore, they do not require a power source. Accordingly, minimizing the power consumption and the implementation area are usually the main design considerations. This paper presents a complete analysis on designing a passive RFID tag. A system design methodology is introduced including the main issues and tradeoffs between different design parameters. The uplink modulation techniques used (ASK, PSK, FSK, and PWM) are illustrated showing how to choose the appropriate signaling scheme for a specific data rate, a certain distance of operation and a limited power consumption budget. An antenna system (transmitter and receiver) is proposed providing the maximum distance of operation with the transmitted power stated by FCC regulations. The backscatter modulation scheme used in the downlink is shown whether to be ASK-BM or PSK-BM and the differences between them are discussed. The key building blocks such as the charge pump, voltage reference, and the regulator used to generate the DC supply voltage from the incoming RF signal are discussed along with their design tradeoffs. A complete architecture for a passive RFID tag is provided as an example to illustrate the proposed RFID tag design methodology.

Training the next generation of psychotraumatologists: COllaborative Network for Training and EXcellence in psychoTraumatology (CONTEXT)

PubMed Central

Vallières, Frédérique; Hyland, Philip; Murphy, Jamie; Hansen, Maj; Shevlin, Mark; Elklit, Ask; Ceannt, Ruth; Armour, Cherie; Wiedemann, Nana; Munk, Mette; Dinesen, Cecilie; O’Hare, Geraldine; Cunningham, Twylla; Askerod, Ditte; Spitz, Pernille; Blackwell, Noeline; McCarthy, Angela; O’Dowd, Leonie; Scott, Shirley; Reid, Tracey; Mokake, Andreas; Halpin, Rory; Perera, Camila; Gleeson, Christina; Frost, Rachel; Flanagan, Natalie; Aldamman, Kinan; Tamrakar, Trina; Louison Vang, Maria; Sherwood, Larissa; Travers, Áine; Haahr-Pedersen, Ida; Walshe, Catherine; McDonagh, Tracey; Bramsen, Rikke Holm

2018-01-01

ABSTRACT In this paper we present a description of the Horizon2020, Marie Skłodowska-Curie Action funded, research and training programme CONTEXT: COllaborative Network for Training and EXcellence in psychoTraumatology. The three objectives of the programme are put forward, each of which refers to a key component of the CONTEXT programme. First, we summarize the 12 individual research projects that will take place across three priority populations: (i) refugees and asylum seekers, (ii) first responders, and (iii) perpetrators and survivors of childhood and gender-based violence. Second, we detail the mentoring and training programme central to CONTEXT. Finally, we describe how the research, together with the training, will contribute towards better policy, guidelines, and practice within the field of psychotraumatology. PMID:29372015

Training the next generation of psychotraumatologists: COllaborative Network for Training and EXcellence in psychoTraumatology (CONTEXT).

PubMed

Vallières, Frédérique; Hyland, Philip; Murphy, Jamie; Hansen, Maj; Shevlin, Mark; Elklit, Ask; Ceannt, Ruth; Armour, Cherie; Wiedemann, Nana; Munk, Mette; Dinesen, Cecilie; O'Hare, Geraldine; Cunningham, Twylla; Askerod, Ditte; Spitz, Pernille; Blackwell, Noeline; McCarthy, Angela; O'Dowd, Leonie; Scott, Shirley; Reid, Tracey; Mokake, Andreas; Halpin, Rory; Perera, Camila; Gleeson, Christina; Frost, Rachel; Flanagan, Natalie; Aldamman, Kinan; Tamrakar, Trina; Louison Vang, Maria; Sherwood, Larissa; Travers, Áine; Haahr-Pedersen, Ida; Walshe, Catherine; McDonagh, Tracey; Bramsen, Rikke Holm

2018-01-01

In this paper we present a description of the Horizon2020, Marie Skłodowska-Curie Action funded, research and training programme CONTEXT: COllaborative Network for Training and EXcellence in psychoTraumatology. The three objectives of the programme are put forward, each of which refers to a key component of the CONTEXT programme. First, we summarize the 12 individual research projects that will take place across three priority populations: (i) refugees and asylum seekers, (ii) first responders, and (iii) perpetrators and survivors of childhood and gender-based violence. Second, we detail the mentoring and training programme central to CONTEXT. Finally, we describe how the research, together with the training, will contribute towards better policy, guidelines, and practice within the field of psychotraumatology.

The value of theory in programmes to implement clinical guidelines: Insights from a retrospective mixed-methods evaluation of a programme to increase adherence to national guidelines for chronic disease in primary care

PubMed Central

Sheringham, Jessica; Solmi, Francesca; Ariti, Cono; Baim-Lance, Abigail; Morris, Steve; Fulop, Naomi J.

2017-01-01

Background Programmes have had limited success in improving guideline adherence for chronic disease. Use of theory is recommended but is often absent in programmes conducted in ‘real-world’ rather than research settings. Materials and methods This mixed-methods study tested a retrospective theory-based approach to evaluate a ‘real-world’ programme in primary care to improve adherence to national guidelines for chronic obstructive pulmonary disease (COPD). Qualitative data, comprising analysis of documents generated throughout the programme (n>300), in-depth interviews with planners (clinicians, managers and improvement experts involved in devising, planning, and implementing the programme, n = 14) and providers (practice clinicians, n = 14) were used to construct programme theories, experiences of implementation and contextual factors influencing care. Quantitative analyses comprised controlled before-and-after analyses to test ‘early’ and evolved’ programme theories with comparators grounded in each theory. ‘Early’ theory predicted the programme would reduce emergency hospital admissions (EHA). It was tested using national analysis of standardized borough-level EHA rates between programme and comparator boroughs. ‘Evolved’ theory predicted practices with higher programme participation would increase guideline adherence and reduce EHA and costs. It was tested using a difference-in-differences analysis with linked primary and secondary care data to compare changes in diagnosis, management, EHA and costs, over time and by programme participation. Results Contrary to programme planners’ predictions in ‘early’ and ‘evolved’ programme theories, admissions did not change following the programme. However, consistent with ‘evolved’ theory, higher guideline adoption occurred in practices with greater programme participation. Conclusions Retrospectively constructing theories based on the ideas of programme planners can enable evaluators to address some limitations encountered when evaluating programmes without a theoretical base. Prospectively articulating theory aided by existing models and mid-range implementation theories may strengthen guideline adoption efforts by prompting planners to scrutinise implementation methods. Benefits of deriving programme theory, with or without the aid of mid-range implementation theories, however, may be limited when the evidence underpinning guidelines is flawed. PMID:28328942

Antibiotics Smart Use: a workable model for promoting the rational use of medicines in Thailand.

PubMed

Sumpradit, Nithima; Chongtrakul, Pisonthi; Anuwong, Kunyada; Pumtong, Somying; Kongsomboon, Kedsenee; Butdeemee, Parichart; Khonglormyati, Jurairat; Chomyong, Santi; Tongyoung, Parnuchote; Losiriwat, Suraphol; Seesuk, Piyanooch; Suwanwaree, Pongthep; Tangcharoensathien, Viroj

2012-12-01

The Antibiotics Smart Use (ASU) programme was introduced in Thailand as a model to promote the rational use of medicines, starting with antibiotics. The programme's first phase consisted of assessing interventions intended to change prescribing practices; the second phase examined the feasibility of programme scale-up. Currently the programme is in its third phase, which centres on sustainability. This paper describes the concept behind ASU, the programme's functional modalities, the development of its conceptual framework and the implementation of its first and second phases. To change antibiotic prescription practices, multifaceted interventions at the individual and organizational levels were implemented; to maintain behaviour change and scale up the programme, interventions at the network and policy levels were used. The National Health Security Office has adopted ASU as a pay-for-performance criterion, a major achievement that has led to the programme's expansion nationwide. Despite limited resources, programme scale-up and sustainability have been facilitated by the promotion of local ownership and mutual recognition, which have generated pride and commitment. ASU is clearly a workable entry point for efforts to rationalize the use of medicines in Thailand. Its long-term sustainability will require continued local commitment and political support, effective auditing and integration of ASU into routine systems with appropriate financial incentives.

National infection prevention and control programmes: Endorsing quality of care.

PubMed

Stempliuk, Valeska; Ramon-Pardo, Pilar; Holder, Reynaldo

2014-01-01

Core components Health care-associated infections (HAIs) are a major cause of morbidity and mortality. In addition to pain and suffering, HAIs increase the cost of health care and generates indirect costs from loss of productivity for patients and society as a whole. Since 2005, the Pan American Health Organization has provided support to countries for the assessment of their capacities in infection prevention and control (IPC). More than 130 hospitals in 18 countries were found to have poor IPC programmes. However, in the midst of many competing health priorities, IPC programmes are not high on the agenda of ministries of health, and the sustainability of national programmes is not viewed as a key point in making health care systems more consistent and trustworthy. Comprehensive IPC programmes will enable countries to reduce the mobility, mortality and cost of HAIs and improve quality of care. This paper addresses the relevance of national infection prevention and control (NIPC) programmes in promoting, supporting and reinforcing IPC interventions at the level of hospitals. A strong commitment from national health authorities in support of national IPC programmes is crucial to obtaining a steady decrease of HAIs, lowering health costs due to HAIs and ensuring safer care.

The use of a modified pairwise comparison method in evaluating critical success factors for community-based rural homestay programmes

NASA Astrophysics Data System (ADS)

Daud, Shahidah Md; Ramli, Razamin; Kasim, Maznah Mat; Kayat, Kalsom; Razak, Rafidah Abd

2014-12-01

Tourism industry has become the highlighted sector which has amazingly increased the national income level. Despite the tourism industry being one of the highest income generating sectors, Homestay Programme as a Community-Based Tourism (CBT) product in Malaysia does not absorbed much of the incoming wealth. Homestay Programme refers to a programme in a community where a tourist stays together with a host family and experiences the everyday way of life of the family in both direct and indirect manner. There are over 100 Homestay Programme currently being registered with the Ministry of Culture and Tourism Malaysia which mostly are located in rural areas, but only a few excel and enjoying the fruit of the booming industry. Hence, this article seeks to identify the critical success factors for a Community-Based Rural Homestay Programme in Malaysia. A modified pairwise method is utilized to further evaluate the identified success factors in a more meaningful way. The findings will help Homestay Programme function as a community development tool that manages tourism resources. Thus, help the community in improving local economy and creating job opportunities.

Cost and results of information systems for health and poverty indicators in the United Republic of Tanzania.

PubMed Central

Rommelmann, Vanessa; Setel, Philip W.; Hemed, Yusuf; Angeles, Gustavo; Mponezya, Hamisi; Whiting, David; Boerma, Ties

2005-01-01

OBJECTIVE: To examine the costs of complementary information generation activities in a resource-constrained setting and compare the costs and outputs of information subsystems that generate the statistics on poverty, health and survival required for monitoring, evaluation and reporting on health programmes in the United Republic of Tanzania. METHODS: Nine systems used by four government agencies or ministries were assessed. Costs were calculated from budgets and expenditure data made available by information system managers. System coverage, quality assurance and information production were reviewed using questionnaires and interviews. Information production was characterized in terms of 38 key sociodemographic indicators required for national programme monitoring. FINDINGS: In 2002-03 approximately US$ 0.53 was spent per Tanzanian citizen on the nine information subsystems that generated information on 37 of the 38 selected indicators. The census and reporting system for routine health service statistics had the largest participating populations and highest total costs. Nationally representative household surveys and demographic surveillance systems (which are not based on nationally representative samples) produced more than half the indicators and used the most rigorous quality assurance. Five systems produced fewer than 13 indicators and had comparatively high costs per participant. CONCLUSION: Policy-makers and programme planners should be aware of the many trade-offs with respect to system costs, coverage, production, representativeness and quality control when making investment choices for monitoring and evaluation. In future, formal cost-effectiveness studies of complementary information systems would help guide investments in the monitoring, evaluation and planning needed to demonstrate the impact of poverty-reduction and health programmes. PMID:16184275

Programmable personality interface for the dynamic infrared scene generator (IRSG2)

NASA Astrophysics Data System (ADS)

Buford, James A., Jr.; Mobley, Scott B.; Mayhall, Anthony J.; Braselton, William J.

1998-07-01

As scene generator platforms begin to rely specifically on commercial off-the-shelf (COTS) hardware and software components, the need for high speed programmable personality interfaces (PPIs) are required for interfacing to Infrared (IR) flight computer/processors and complex IR projectors in the hardware-in-the-loop (HWIL) simulation facilities. Recent technological advances and innovative applications of established technologies are beginning to allow development of cost effective PPIs to interface to COTS scene generators. At the U.S. Army Aviation and Missile Command (AMCOM) Missile Research, Development, and Engineering Center (MRDEC) researchers have developed such a PPI to reside between the AMCOM MRDEC IR Scene Generator (IRSG) and either a missile flight computer or the dynamic Laser Diode Array Projector (LDAP). AMCOM MRDEC has developed several PPIs for the first and second generation IRSGs (IRSG1 and IRSG2), which are based on Silicon Graphics Incorporated (SGI) Onyx and Onyx2 computers with Reality Engine 2 (RE2) and Infinite Reality (IR/IR2) graphics engines. This paper provides an overview of PPIs designed, integrated, tested, and verified at AMCOM MRDEC, specifically the IRSG2's PPI.

A high-resolution programmable Vernier delay generator based on carry chains in FPGA

NASA Astrophysics Data System (ADS)

Cui, Ke; Li, Xiangyu; Zhu, Rihong

2017-06-01

This paper presents an architecture of a high-resolution delay generator implemented in a single field programmable gate array chip by exploiting the method of utilizing dedicated carry chains. It serves as the core component in various physical instruments. The proposed delay generator contains the coarse delay step and the fine delay step to guarantee both large dynamic range and high resolution. The carry chains are organized in the Vernier delay loop style to fulfill the fine delay step with high precision and high linearity. The delay generator was implemented in the EP3SE110F1152I3 Stratix III device from Altera on a self-designed test board. Test results show that the obtained resolution is 38.6 ps, and the differential nonlinearity/integral nonlinearity is in the range of [-0.18 least significant bit (LSB), 0.24 LSB]/(-0.02 LSB, 0.01 LSB) under the nominal supply voltage of 1100 mV and environmental temperature of 2 0°C. The delay generator is rather efficient concerning resource cost, which uses only 668 look-up tables and 146 registers in total.

New model of inverting substation for DC traction with regenerative braking system

NASA Astrophysics Data System (ADS)

Omar, Abdul Malek Saidina; Samat, Ahmad Asri Abd; Isa, Siti Sarah Mat; Shamsuddin, Sarah Addyani; Jamaludin, Nur Fadhilah; Khyasudeen, Muhammad Farris

2017-08-01

This paper presents a power electronic devices application focus on modeling, analysis, and control of switching power converter in the inverting DC substation with regenerative braking system which is used to recycle the surplus regenerative power by feed it back to the main AC grid. The main objective of this research is to improve the switching power electronic converter of the railway inverting substation and optimize the maximum kinetic energy recovery together with minimum power losses from the railway braking system. Assess performance including efficiency and robustness will be evaluated in order to get the best solution for the design configuration. Research methodology included mathematical calculation, simulation, and detail analysis on modeling of switching power converter on inverting substation. The design stage separates to four main areas include rectification mode, regenerative mode, control inverter mode and filtering mode. The simulation result has shown that the regenerative inverter has a capability to accept a maximum recovery power on the regeneration mode. Total energy recovery has increase and power losses have decreases because inverter abilities to transfer the surplus energy back to the main AC supply. An Inverter controller with PWM Generator and PI Voltage Regulator has been designed to control voltage magnitude and frequency of the DC traction system.

A Flexible Microcontroller-Based Data Acquisition Device

PubMed Central

Hercog, Darko; Gergič, Bojan

2014-01-01

This paper presents a low-cost microcontroller-based data acquisition device. The key component of the presented solution is a configurable microcontroller-based device with an integrated USB transceiver and a 12-bit analogue-to-digital converter (ADC). The presented embedded DAQ device contains a preloaded program (firmware) that enables easy acquisition and generation of analogue and digital signals and data transfer between the device and the application running on a PC via USB bus. This device has been developed as a USB human interface device (HID). This USB class is natively supported by most of the operating systems and therefore any installation of additional USB drivers is unnecessary. The input/output peripheral of the presented device is not static but rather flexible, and could be easily configured to customised needs without changing the firmware. When using the developed configuration utility, a majority of chip pins can be configured as analogue input, digital input/output, PWM output or one of the SPI lines. In addition, LabVIEW drivers have been developed for this device. When using the developed drivers, data acquisition and signal processing algorithms as well as graphical user interface (GUI), can easily be developed using a well-known, industry proven, block oriented LabVIEW programming environment. PMID:24892494

An electromagnetic microvalve for pneumatic control of microfluidic systems.

PubMed

Liu, Xuling; Li, Songjing

2014-10-01

An electromagnetic microvalve for pneumatic control of microfluidic devices has been designed, fabricated, and tested. The microvalve is composed of two parts: a miniature electromagnetic actuator and a valve body. The electromagnetic actuator consists mainly of a thin polydimethylsiloxane (PDMS)-based elastomer, which acts as the valve diaphragm. The diaphragm, used as a solid hydraulic medium, converts the large contact area of a valve core into a small contact area of valve head while maintaining a large stroking force. This microvalve remains closed because of a compressed mechanical spring force generated by the actuator. On the other hand, when a voltage is applied, the valve core moves up, relaxing the thin PDMS membrane, opening the microvalve. The fast open response (~17 ms) of the valve was achieved with a leak rate as low as 0.026 sccm at 200 KPa (N2) pressure. We tested the pertinent dynamic parameters such as flow rate in on/off mode, flow rate of duty cycles, and actuated frequencies in pulse width modulation (PWM) mode. Our method provides a simple, cheap, and small microvalve that avoids the bulky and expensive external pressure control solenoid manifold. This allows it to be easily integrated into portable and disposable devices. © 2014 Society for Laboratory Automation and Screening.

CGAT: a model for immersive personalized training in computational genomics.

PubMed

Sims, David; Ponting, Chris P; Heger, Andreas

2016-01-01

How should the next generation of genomics scientists be trained while simultaneously pursuing high quality and diverse research? CGAT, the Computational Genomics Analysis and Training programme, was set up in 2010 by the UK Medical Research Council to complement its investment in next-generation sequencing capacity. CGAT was conceived around the twin goals of training future leaders in genome biology and medicine, and providing much needed capacity to UK science for analysing genome scale data sets. Here we outline the training programme employed by CGAT and describe how it dovetails with collaborative research projects to launch scientists on the road towards independent research careers in genomics. © The Author 2015. Published by Oxford University Press.

Capacity building for global nursing leaders: challenges and experiences.

PubMed

Shin, S; Han, J; Cha, C

2016-12-01

The aim of this article is to describe our experience in operating a capacity-building programme, the Korea International Cooperation Project, for global nursing leaders from developing countries, held during the International Council of Nurses (ICN) Conference in 2015 in Seoul, Korea. Globalization points to the importance of global leadership among nursing leaders. In accordance with the theme of 'Global Citizen, Global Nursing' at the ICN conference in 2015, a capacity-building programme for nursing leaders of developing countries was implemented. The global nursing leadership programme shared experiences during the preparation and operation of the conference. To prepare the programme, this paper describes selecting participants, working with invitation lists from 30 countries, and recruiting and training volunteers. The operation of the programme, orientation, organizing tailored programmes for participant groups, addressing unexpected issues and evaluating the programme are described. ICN could implement capacity-building programmes for nursing leaders of developing countries during its ICN conference for the nursing society. A programme tailored for each continent with similar sociocultural backgrounds and health issues would provide chances for collaboration and networking. A policy to compile global nursing indicators should be developed. This would allow nursing leaders to learn about the strengths and weaknesses of global nursing and provide evidence for collaboration. The programme was successful in introducing and broadening global perspectives of participants on health and education as well as building a network among leaders and next-generation leaders in participating countries for future cooperation and collaboration. © 2016 International Council of Nurses.

Research capacity building in midwifery: Case study of an Australian Graduate Midwifery Research Intern Programme.

PubMed

Hauck, Yvonne L; Lewis, Lucy; Bayes, Sara; Keyes, Louise

2015-09-01

Having the research capacity to identify problems, create new knowledge and most importantly translate this knowledge into practice is essential within health care. Midwifery, as well as other health professions in Australia, is challenged in building its research capacity to contribute evidence to inform clinical practice. The aim of this project was to evaluate an innovative Graduate Midwifery Research Intern Programme offered at a tertiary obstetric hospital in Western Australia, to determine what was working well and how the programme could be improved. A case study approach was used to gain feedback from graduate midwives within a Graduate Research Intern (GRI) Programme. In addition outcomes were compiled of all projects the GRI midwives contributed to. Six GRI midwives participated in a survey comprising of four open ended questions to provide feedback about the programme. Findings confirm that the GRI programme increased the graduates understanding of how research works, its capacity to define a problem, generate new knowledge and inform clinical practice. The GRI midwives' feedback suggested the programme opened their thinking to future study and gave them enhanced insight into women's experiences around childbirth. To grow our knowledge as a professional group, midwives must develop and promote programmes to build our pool of research capable midwives. By sharing our programme evaluation we hope to entice other clinical settings to consider the value in replicating such a programme within their context. Copyright © 2015 Australian College of Midwives. Published by Elsevier Ltd. All rights reserved.

Method and infrastructure for cycle-reproducible simulation on large scale digital circuits on a coordinated set of field-programmable gate arrays (FPGAs)

DOEpatents

Asaad, Sameh W; Bellofatto, Ralph E; Brezzo, Bernard; Haymes, Charles L; Kapur, Mohit; Parker, Benjamin D; Roewer, Thomas; Tierno, Jose A

2014-01-28

A plurality of target field programmable gate arrays are interconnected in accordance with a connection topology and map portions of a target system. A control module is coupled to the plurality of target field programmable gate arrays. A balanced clock distribution network is configured to distribute a reference clock signal, and a balanced reset distribution network is coupled to the control module and configured to distribute a reset signal to the plurality of target field programmable gate arrays. The control module and the balanced reset distribution network are cooperatively configured to initiate and control a simulation of the target system with the plurality of target field programmable gate arrays. A plurality of local clock control state machines reside in the target field programmable gate arrays. The local clock state machines are configured to generate a set of synchronized free-running and stoppable clocks to maintain cycle-accurate and cycle-reproducible execution of the simulation of the target system. A method is also provided.

Roll Angle Estimation Using Thermopiles for a Flight Controlled Mortar

DTIC Science & Technology

2012-06-01

Using Xilinx’s System generator, the entire design was implemented at a relatively high level within Malab’s Simulink. This allowed VHDL code to...thermopile data with a Recursive Least Squares (RLS) filter implemented on a field programmable gate array (FPGA). These results demonstrate the...accurately estimated by processing the thermopile data with a Recursive Least Squares (RLS) filter implemented on a field programmable gate array (FPGA

Daughters of the Earth: Skills-Based Literacy Programme for Women, China. Education for All: Making It Work. Innovation Series.

ERIC Educational Resources Information Center

Aksornkool, Namtip

Begun in the early 1990s, The Skills-Based Literacy Programme for Women aims to improve the lives of rural Chinese women by linking literacy education with skills training in agriculture and other forms of income generation. Xuan Wei County, Yunnan Province, was chosen as the seat of the project because of high female illiteracy rates and the need…

Digital micromirror device as programmable rough particle in interferometric particle imaging.

PubMed

Fromager, M; Aït Ameur, K; Brunel, M

2017-04-20

The 2D autocorrelation of the projection of an irregular rough particle can be estimated using the analysis of its interferometric out-of-focus image. We report the development of an experimental setup that creates speckle-like patterns generated by "programmable" rough particles of desired-shape. It should become an important tool for the development of new setups, configurations, and algorithms in interferometric particle imaging.

Reaching the Next Generation of Marine Scientists

NASA Astrophysics Data System (ADS)

Joyce, J.

2009-04-01

The next generation of marine scientists are today at primary school, secondary school or at college. To encourage them in their career, and to introduce those who are as yet undecided to the wonders of marine science, the Irish Marine Institute has devised a series of three overlapping outreach programmes to reach children at all three levels. Beginning at primary school, the "Explorers" programme offers a range of resources to teachers to enable them to teach marine-related examples as part of the science or geography modules of the SESE curriculum. These include teacher training, expert visits to schools, the installation and stocking of aquaria, field trips and downloadable lesson plans. For older pupils, the "Follow the Fleet" programme is a web-based education asset that allows users to track individual merchant ships and research vessels across the world, to interact with senior crew members of ships and to learn about their cargoes, the ports they visit and the sea conditions along the way. Finally, the "Integrated Marine Exploration Programme (IMEP)" takes secondary school pupils and university students to sea aboard the Marine Institute's research vessels to give them a taste of life as a marine scientist or to educate them in the practical day-to-day sampling and data processing tasks that make up a marine scientist's job.

Sustainability of recurrent expenditure on public social welfare programmes: expenditure analysis of the free maternal care programme of the Ghana National Health Insurance Scheme.

PubMed

Ankrah Odame, Emmanuel; Akweongo, Patricia; Yankah, Ben; Asenso-Boadi, Francis; Agyepong, Irene

2014-05-01

Sustainability of public social welfare programmes has long been of concern in development circles. An important aspect of sustainability is the ability to sustain the recurrent financial costs of programmes. A free maternal care programme (FMCP) was launched under the Ghana National Health Insurance Scheme (NHIS) in 2008 with a start-up grant from the British Government. This article examines claims expenditure under the programme and the implications for the financial sustainability of the programme, and the lessons for donor and public financing of social welfare programmes. Records of reimbursement claims for services and medicines by women benefitting from the policy in participating facilities in one sub-metropolis in Ghana were analysed to gain an understanding of the expenditure on this programme at facility level. National level financial inflow and outflow (expenditure) data of the NHIS, related to implementation of this policy for 2008 and 2009, were reviewed to put the facility-based data in the national perspective. A total of US$936 450.94 was spent in 2009 by the scheme on FMCP in the sub-metropolis. The NHIS expenditure on the programme for the entire country in 2009 was US$49.25 million, exceeding the British grant of US$10.00 million given for that year. Subsequently, the programme has been entirely financed by the National Health Insurance Fund. The rapidly increasing, recurrent demands on this fund from the maternal delivery exemption programme-without a commensurate growth on the amounts generated annually-is an increasing threat to the sustainability of the fund. Provision of donor start-up funding for programmes with high recurrent expenditures, under the expectation that government will take over and sustain the programme, must be accompanied by clear long-term analysis and planning as to how government will sustain the programme.

Training in the prevention of cervical cancer: advantages of e-learning

PubMed Central

Company, Assumpta; Montserrat, Mireia; Bosch, Francesc X; de Sanjosé, Silvia

2015-01-01

Cervical cancer remains the second most common cancer for women worldwide and is the cancer priority in most low- and middle-income countries (LMIC). The development of vaccines against the human papilloma virus (HPV) and the impact of technology both for the detection of HPV and cervical cancer represent milestones and new opportunities in prevention. New internet-based technologies are generating mass access to training programmes. This article presents the methodology for developing an online training programme for the prevention of cervical cancer as well as the results obtained during the four year period wherein the same programme was delivered in Latin America. PMID:26557878

Training in the prevention of cervical cancer: advantages of e-learning.

PubMed

Company, Assumpta; Montserrat, Mireia; Bosch, Francesc X; de Sanjosé, Silvia

2015-01-01

Cervical cancer remains the second most common cancer for women worldwide and is the cancer priority in most low- and middle-income countries (LMIC). The development of vaccines against the human papilloma virus (HPV) and the impact of technology both for the detection of HPV and cervical cancer represent milestones and new opportunities in prevention. New internet-based technologies are generating mass access to training programmes. This article presents the methodology for developing an online training programme for the prevention of cervical cancer as well as the results obtained during the four year period wherein the same programme was delivered in Latin America.

Failure of attenuated canine distemper virus (Rockborn strain) to suppress lymphocyte blastogenesis in dogs.

PubMed

Schultz, R D

1976-01-01

The attenuated Rockborn strain of canine distemper virus is commonly used in commercial vaccines. Since immunosuppression is a common feature of virulent (Snyder Hill) distemper virus infection of the dog, an evaluation of the cellular immune functions of dogs given inoculums of the less virulent Rockborn strain was done using lymphocyte blastogenesis responses to various mitogens. Unlike the viruslent Snyder Hill strain, the attenuated distemper virus did not alter lymphocyte blastogenesis responses to phytohemaglutinin (PHA) and pokeweed mitogen (PWM) which are considered in vitro correlates of T and B cell immunity.

PWMScan: a fast tool for scanning entire genomes with a position-specific weight matrix.

PubMed

Ambrosini, Giovanna; Groux, Romain; Bucher, Philipp

2018-03-05

Transcription factors (TFs) regulate gene expression by binding to specific short DNA sequences of 5 to 20-bp to regulate the rate of transcription of genetic information from DNA to messenger RNA. We present PWMScan, a fast web-based tool to scan server-resident genomes for matches to a user-supplied PWM or TF binding site model from a public database. The web server and source code are available at http://ccg.vital-it.ch/pwmscan and https://sourceforge.net/projects/pwmscan, respectively. giovanna.ambrosini@epfl.ch. SUPPLEMENTARY DATA ARE AVAILABLE AT BIOINFORMATICS ONLINE.

Report of Combat Consumption Modeling Improvement Panel.

DTIC Science & Technology

1980-07-01

within a static frame- work , and so may require the use of a dynamic approach. 5. Navy Methodologies ( Less Risk) Like the Air Force, the Navy uses a...mda~id iw Cumr MOAN3 70 C 620 Ib9 Umplmmut d6 Um. IN PWmAN d WM A PaW dme adn hiSses by Onbs ds dmu~m. p.1Mm d6 tga agmey. UNCLASSIFIED lecumV...by ,the panel to be important, in detail. In many areas, the panel believes that the caveats and recommendations for future work presented In the DoD

Reprogramming mouse fibroblasts into engraftable myeloerythroid and lymphoid progenitors

PubMed Central

Cheng, Hui; Ang, Heather Yin-Kuan; A. EL Farran, Chadi; Li, Pin; Fang, Hai Tong; Liu, Tong Ming; Kong, Say Li; Chin, Michael Lingzi; Ling, Wei Yin; Lim, Edwin Kok Hao; Li, Hu; Huber, Tara; Loh, Kyle M.; Loh, Yuin-Han; Lim, Bing

2016-01-01

Recent efforts have attempted to convert non-blood cells into hematopoietic stem cells (HSCs) with the goal of generating blood lineages de novo. Here we show that hematopoietic transcription factors Scl, Lmo2, Runx1 and Bmi1 can convert a developmentally distant lineage (fibroblasts) into ‘induced hematopoietic progenitors' (iHPs). Functionally, iHPs generate acetylcholinesterase+ megakaryocytes and phagocytic myeloid cells in vitro and can also engraft immunodeficient mice, generating myeloerythoid and B-lymphoid cells for up to 4 months in vivo. Molecularly, iHPs transcriptionally resemble native Kit+ hematopoietic progenitors. Mechanistically, reprogramming factor Lmo2 implements a hematopoietic programme in fibroblasts by rapidly binding to and upregulating the Hhex and Gfi1 genes within days. Moreover the reprogramming transcription factors also require extracellular BMP and MEK signalling to cooperatively effectuate reprogramming. Thus, the transcription factors that orchestrate embryonic hematopoiesis can artificially reconstitute this programme in developmentally distant fibroblasts, converting them into engraftable blood progenitors. PMID:27869129

Novel programmable microwave photonic filter with arbitrary filtering shape and linear phase.

PubMed

Zhu, Xiaoqi; Chen, Feiya; Peng, Huanfa; Chen, Zhangyuan

2017-04-17

We propose and demonstrate a novel optical frequency comb (OFC) based microwave photonic filter which is able to realize arbitrary filtering shape with linear phase response. The shape of filter response is software programmable using finite impulse response (FIR) filter design method. By shaping the OFC spectrum using a programmable waveshaper, we can realize designed amplitude of FIR taps. Positive and negative sign of FIR taps are achieved by balanced photo-detection. The double sideband (DSB) modulation and symmetric distribution of filter taps are used to maintain the linear phase condition. In the experiment, we realize a fully programmable filter in the range from DC to 13.88 GHz. Four basic types of filters (lowpass, highpass, bandpass and bandstop) with different bandwidths, cut-off frequencies and central frequencies are generated. Also a triple-passband filter is realized in our experiment. To the best of our knowledge, it is the first demonstration of a programmable multiple passband MPF with linear phase response. The experiment shows good agreement with the theoretical result.

Programmable Numerical Function Generators: Architectures and Synthesis Method

DTIC Science & Technology

2005-08-01

generates HDL (Hardware Descrip- tion Language) code from the design specification described by Scilab [14], a MATLAB-like numerical calculation soft...cad.com/Error-NFG/. [14] Scilab 3.0, INRIA-ENPC, France, http://scilabsoft.inria.fr/ [15] M. J. Schulte and J. E. Stine, “Approximating elementary functions

Taking the business continuity programme to a corporate leadership role.

PubMed

Messer, Ira

2009-11-01

The paper discusses a process to raise the awareness and value of your continuity programme to higher levels by leveraging existing data. It gives examples of how to utilise the structure of the Business Impact Analysis tool to develop an enterprise level of information capture, and then utilise that data to generate an enterprise level 'group think' which results in incorporation of business continuity as a part of the business-as-usual model.

Women's participation in rural credit programmes in Bangladesh and their demand for formal health care: is there a positive impact?

PubMed

Nanda, P

1999-08-01

Within the overall aim of poverty alleviation, development efforts have included credit and self-employment programmes. In Bangladesh, the major beneficiaries of such group-based credit programmes are rural women who use the loans to initiate small informal income-generating activities. This paper explores the benefits of women's participation in credit programmes on their own health seeking. Using data from a sample of 1798 households from rural Bangladesh, conducted in 1991-1992 through repeated random sampling of 87 districts covered by Grameen Bank, Bangladesh Rural Advancement Committee (BRAC) and Bangladesh Rural Development Board (BRDB), this paper addresses the question: does women's participation in credit programmes significantly affect their use of formal health care? A non-unitary household preference model is suggested to test the hypothesis that women's empowerment through participation in these programmes results in greater control of resources for their own demand for formal health care. The analysis controls for endogeneity due to self-selection and other unobserved village level factors through the use of a weighted two stage instrumental variable approach with village level fixed effects. The findings indicate a positive impact of women's participation in credit programmes on their demand for formal health care. The policy simulations on the results of this study highlight the importance of credit programmes as a health intervention in addition to being a mechanism for women's economic empowerment.

Introduction to the novel verification concept of the instrument performances for the Meteosat third generation infrared sounder instrument (mtg-irs)

NASA Astrophysics Data System (ADS)

Freudling, M.; Egner, S.; Hering, M.; Carbó, F. L.; Thiele, H.

2017-09-01

The Meteosat Third Generation (MTG) Programme will ensure the future continuity and enhancement of meteorological data from geostationary orbit as currently provided by the Meteosat Second Generation (MSG) system. The industrial prime contractor for the space segment is Thales Alenia Space (France), with a core team consortium including OHB System AG (Germany).

Punch Card Programmable Microfluidics

PubMed Central

Korir, George; Prakash, Manu

2015-01-01

Small volume fluid handling in single and multiphase microfluidics provides a promising strategy for efficient bio-chemical assays, low-cost point-of-care diagnostics and new approaches to scientific discoveries. However multiple barriers exist towards low-cost field deployment of programmable microfluidics. Incorporating multiple pumps, mixers and discrete valve based control of nanoliter fluids and droplets in an integrated, programmable manner without additional required external components has remained elusive. Combining the idea of punch card programming with arbitrary fluid control, here we describe a self-contained, hand-crank powered, multiplex and robust programmable microfluidic platform. A paper tape encodes information as a series of punched holes. A mechanical reader/actuator reads these paper tapes and correspondingly executes operations onto a microfluidic chip coupled to the platform in a plug-and-play fashion. Enabled by the complexity of codes that can be represented by a series of holes in punched paper tapes, we demonstrate independent control of 15 on-chip pumps with enhanced mixing, normally-closed valves and a novel on-demand impact-based droplet generator. We demonstrate robustness of operation by encoding a string of characters representing the word “PUNCHCARD MICROFLUIDICS” using the droplet generator. Multiplexing is demonstrated by implementing an example colorimetric water quality assays for pH, ammonia, nitrite and nitrate content in different water samples. With its portable and robust design, low cost and ease-of-use, we envision punch card programmable microfluidics will bring complex control of microfluidic chips into field-based applications in low-resource settings and in the hands of children around the world. PMID:25738834

Maintaining Unity - relatives in older patients' fast-track treatment programmes. A grounded theory study.

PubMed

Berthelsen, Connie Bøttcher; Lindhardt, Tove; Frederiksen, Kirsten

2014-12-01

To generate a substantive grounded theory of relatives' pattern of behaviour in older patients' fast-track treatment programmes during total hip or knee replacement. Fast-track treatment programmes are designed to make total hip and knee replacements more efficient through recovery improvements. The support of relatives during older patients' trajectory is important. However, knowledge is needed on the relatives' pattern of behaviour to strengthen their involvement in fast-track treatment programmes. We used a Glaserian grounded theory approach based on a systematic generation of theory from data to explain the latent pattern of behaviour of relatives. Data were collected from 2010-2011 in orthopaedic wards at two Danish university hospitals and consisted of 14 non-participant observations, 14 postobservational interviews and five interviews. Seven relatives of patients over 70 years of age participated. The constant comparative method was the guiding principle for simultaneous data collection, data analysis and coding, while theoretically sampling and writing memos. Maintaining Unity emerged as the relatives' pattern of behaviour through which they resolved their main concern: preventing the patients from feeling alone. The relatives resolved their main concern through three interchangeable behavioural modes: Protecting Mode, by providing loving and respectful support; Substituting Mode, with practical and cognitive support; and an Adapting Mode, by trying to fit in with the patients' and health professionals' requirements. The substantive theory of Maintaining Unity offers knowledge of relatives' strong desire to provide compassionate and loving support for the older patients during fast-track treatment programmes. © 2014 John Wiley & Sons Ltd.

Punch card programmable microfluidics.

PubMed

Korir, George; Prakash, Manu

2015-01-01

Small volume fluid handling in single and multiphase microfluidics provides a promising strategy for efficient bio-chemical assays, low-cost point-of-care diagnostics and new approaches to scientific discoveries. However multiple barriers exist towards low-cost field deployment of programmable microfluidics. Incorporating multiple pumps, mixers and discrete valve based control of nanoliter fluids and droplets in an integrated, programmable manner without additional required external components has remained elusive. Combining the idea of punch card programming with arbitrary fluid control, here we describe a self-contained, hand-crank powered, multiplex and robust programmable microfluidic platform. A paper tape encodes information as a series of punched holes. A mechanical reader/actuator reads these paper tapes and correspondingly executes operations onto a microfluidic chip coupled to the platform in a plug-and-play fashion. Enabled by the complexity of codes that can be represented by a series of holes in punched paper tapes, we demonstrate independent control of 15 on-chip pumps with enhanced mixing, normally-closed valves and a novel on-demand impact-based droplet generator. We demonstrate robustness of operation by encoding a string of characters representing the word "PUNCHCARD MICROFLUIDICS" using the droplet generator. Multiplexing is demonstrated by implementing an example colorimetric water quality assays for pH, ammonia, nitrite and nitrate content in different water samples. With its portable and robust design, low cost and ease-of-use, we envision punch card programmable microfluidics will bring complex control of microfluidic chips into field-based applications in low-resource settings and in the hands of children around the world.

Programmable quantum random number generator without postprocessing.

PubMed

Nguyen, Lac; Rehain, Patrick; Sua, Yong Meng; Huang, Yu-Ping

2018-02-15

We demonstrate a viable source of unbiased quantum random numbers whose statistical properties can be arbitrarily programmed without the need for any postprocessing such as randomness distillation or distribution transformation. It is based on measuring the arrival time of single photons in shaped temporal modes that are tailored with an electro-optical modulator. We show that quantum random numbers can be created directly in customized probability distributions and pass all randomness tests of the NIST and Dieharder test suites without any randomness extraction. The min-entropies of such generated random numbers are measured close to the theoretical limits, indicating their near-ideal statistics and ultrahigh purity. Easy to implement and arbitrarily programmable, this technique can find versatile uses in a multitude of data analysis areas.

Use of existing data for public health planning: a study of the prevalence of hepatitis B surface antigen and core antibody in Al Ain Medical District, United Arab Emirates.

PubMed Central

al-Owais, A.; al-Suwaidi, K.; Amiri, N.; Carter, A. O.; Hossain, M. M.; Sheek-Hussein, M. M.

2000-01-01

INTRODUCTION: Hepatitis B is of major public health importance. Accurate information on its occurrence, with particular reference to the prevalence of immunity and chronic infection (marked by the presence of hepatitis B core antibody and surface antigen, respectively, in serum), is essential for planning public health programmes for the control of the disease. The generation of marker prevalence data through serological surveys is costly and time-consuming. The present study in Al Ain Medical District, United Arab Emirates, investigated the possibility of obtaining sufficiently accurate marker prevalence estimates from existing data to plan public health programmes. METHODS: Two antenatal screening databases, one student serological survey database, one immunization programme database and one pre-marriage screening database containing information on marker prevalence were identified. Epidemiological data were abstracted from these databases and analysed. RESULTS: The data showed that the prevalence of hepatitis B surface antigen and the prevalence of core antibody in young citizens in 1998 were approximately 2% and 14% respectively, that any immunization campaign aimed at citizens of the United Arab Emirates should target teenagers as they had the highest risk of acquiring the disease, and that pre-immunization screening of young adults would be wasteful. However, the data did not yield information on the prevalence of hepatitis B surface antigen and core antibody in other population subgroups of public health significance. DISCUSSION: While data generated by the study are sufficient to support a hepatitis B immunization programme targeted at teenaged citizens, more accurate data, generated by a well-designed serological survey, would be essential for optimal public health planning. PMID:11143192

Interleukin-10-1082 promoter polymorphism in association with cytokine production and sepsis susceptibility.

PubMed

Stanilova, Spaska A; Miteva, Lyuba D; Karakolev, Zhivko T; Stefanov, Chavdar S

2006-02-01

To investigate the -1082 (A/G) polymorphism in the promoter of the IL-10 gene in terms of IL-10 production from stimulated peripheral blood mononuclear cells (PBMC) and to evaluate the relationship of this polymorphism with susceptibility to severe sepsis and the outcome of the disease. Case-control study. Research laboratory of Molecular Biology and Immunology and University Hospital ICU, Faculty of Medicine, Trakia University. A total of 53 healthy volunteers and 33 patients in ICU meeting the criteria for severe sepsis were included. The amplification refractory mutation system PCR was used for IL-10-1082 polymorphism detection. Isolated PBMC were stimulated with either C3-binding glycoprotein (C3bgp), lipopolysaccharide (LPS), phytohemagglutinin (PHA),or pokeweed mitogen (PWM). IL-10 production was measured in culture supernatants. The AA genotype was associated with lower IL-10 production in LPS-, PHA- or PWM-stimulated healthy PBMC. Patients with severe sepsis had significant elevation of A allele, compared with healthy controls (74.2% vs 52.8%; p=0.0062). Carriage of at least one copy of IL-10-1082 G allele in sepsis patients and in healthy controls resulted in a statistically significant increase in IL-10 production from stimulated PBMC. Surviving sepsis patients had a significant decrease of IL-10-1082 allele G frequency, compared with controls (17% vs 47.2%; p=0.012). An association between increased IL-10 production and poor outcome from sepsis was observed. The A allele of the -1082 polymorphism in the interleukin-10 gene promoter is associated with sepsis susceptibility, whereas G allele is associated with higher stimulated interleukin-10 production and increased mortality in severe sepsis.

Non-word repetition in children with specific language impairment: a deficit in phonological working memory or in long-term verbal knowledge?

PubMed

Casalini, Claudia; Brizzolara, Daniela; Chilosi, Anna; Cipriani, Paola; Marcolini, Stefania; Pecini, Chiara; Roncoli, Silvia; Burani, Cristina

2007-08-01

In this study we investigated the effects of long-term memory (LTM) verbal knowledge on short-term memory (STM) verbal recall in a sample of Italian children affected by different subtypes of specific language impairment (SLI). The aim of the study was to evaluate if phonological working memory (PWM) abilities of SLI children can be supported by LTM linguistic representations and if PWM performances can be differently affected in the various subtypes of SLI. We tested a sample of 54 children affected by Mixed Receptive-Expressive (RE), Expressive (Ex) and Phonological (Ph) SLI (DSM-IV - American Psychiatric Association, 1994) by means of a repetition task of words (W) and non-words (NW) differing in morphemic structure [morphological non-words (MNW), consisting of combinations of roots and affixes - and simple non-words - with no morphological constituency]. We evaluated the effects of lexical and morpho-lexical LTM representations on STM recall by comparing the repetition accuracy across the three types of stimuli. Results indicated that although SLI children, as a group, showed lower repetition scores than controls, their performance was affected similarly to controls by the type of stimulus and the experimental manipulation of the non-words (better repetition of W than MNW and NW, and of MNW than NW), confirming the recourse to LTM verbal representations to support STM recall. The influence of LTM verbal knowledge on STM recall in SLI improved with age and did not differ among the three types of SLI. However, the three types of SLI differed in the accuracy of their repetition performances (PMW abilities), with the Phonological group showing the best scores. The implications for SLI theory and practice are discussed.

Application of drive circuit based on L298N in direct current motor speed control system

NASA Astrophysics Data System (ADS)

Yin, Liuliu; Wang, Fang; Han, Sen; Li, Yuchen; Sun, Hao; Lu, Qingjie; Yang, Cheng; Wang, Quanzhao

2016-10-01

In the experiment of researching the nanometer laser interferometer, our design of laser interferometer circuit system is up to the wireless communication technique of the 802.15.4 IEEE standard, and we use the RF TI provided by Basic to receive the data on speed control system software. The system's hardware is connected with control module and the DC motor. However, in the experiment, we found that single chip microcomputer control module is very difficult to drive the DC motor directly. The reason is that the DC motor's starting and braking current is larger than the causing current of the single chip microcomputer control module. In order to solve this problem, we add a driving module that control board can transmit PWM wave signal through I/O port to drive the DC motor, the driving circuit board can come true the function of the DC motor's positive and reversal rotation and speed adjustment. In many various driving module, the L298N module's integrated level is higher compared with other driver module. The L298N model is easy to control, it not only can control the DC motor, but also achieve motor speed control by modulating PWM wave that the control panel output. It also has the over-current protection function, when the motor lock, the L298N model can protect circuit and motor. So we use the driver module based on L298N to drive the DC motor. It is concluded that the L298N driver circuit module plays a very important role in the process of driving the DC motor in the DC motor speed control system.

Epitope predictions indicate the presence of two distinct types of epitope-antibody-reactivities determined by epitope profiling of intravenous immunoglobulins.

PubMed

Luštrek, Mitja; Lorenz, Peter; Kreutzer, Michael; Qian, Zilliang; Steinbeck, Felix; Wu, Di; Born, Nadine; Ziems, Bjoern; Hecker, Michael; Blank, Miri; Shoenfeld, Yehuda; Cao, Zhiwei; Glocker, Michael O; Li, Yixue; Fuellen, Georg; Thiesen, Hans-Jürgen

2013-01-01

Epitope-antibody-reactivities (EAR) of intravenous immunoglobulins (IVIGs) determined for 75,534 peptides by microarray analysis demonstrate that roughly 9% of peptides derived from 870 different human protein sequences react with antibodies present in IVIG. Computational prediction of linear B cell epitopes was conducted using machine learning with an ensemble of classifiers in combination with position weight matrix (PWM) analysis. Machine learning slightly outperformed PWM with area under the curve (AUC) of 0.884 vs. 0.849. Two different types of epitope-antibody recognition-modes (Type I EAR and Type II EAR) were found. Peptides of Type I EAR are high in tyrosine, tryptophan and phenylalanine, and low in asparagine, glutamine and glutamic acid residues, whereas for peptides of Type II EAR it is the other way around. Representative crystal structures present in the Protein Data Bank (PDB) of Type I EAR are PDB 1TZI and PDB 2DD8, while PDB 2FD6 and 2J4W are typical for Type II EAR. Type I EAR peptides share predicted propensities for being presented by MHC class I and class II complexes. The latter interaction possibly favors T cell-dependent antibody responses including IgG class switching. Peptides of Type II EAR are predicted not to be preferentially presented by MHC complexes, thus implying the involvement of T cell-independent IgG class switch mechanisms. The high extent of IgG immunoglobulin reactivity with human peptides implies that circulating IgG molecules are prone to bind to human protein/peptide structures under non-pathological, non-inflammatory conditions. A webserver for predicting EAR of peptide sequences is available at www.sysmed-immun.eu/EAR.

Optimization of interferon gamma ELISPOT assay to detect human cytomegalovirus specific T-cell responses in solid organ transplants.

PubMed

Abate, Davide; Saldan, Alda; Forner, Gabriella; Tinto, Daniel; Bianchin, Alice; Palù, Giorgio

2014-02-01

Assessing the CMV specific CMI in transplant subjects represents a promising strategy to determine the risk of infection on individual basis. In this study 61 adult CMV IgG seropositive solid organ transplant recipients were examined in order to improve the efficacy of CMI detection. For this purpose, pair-wise comparisons were conducted comparing positive control stimuli PWM and PMA/iono and CMV stimuli, pp65 peptide pool and whole CMV particle. Rosette pre-depletion of blood was also investigated for detecting CD4+ or CD8+ T-cell responses using the IFN-g ELISPOT assay. In the time-points 30-180 days after transplantation, PMA/iono produced statistically significant higher responses compared to PWM, probably because PMA/iono activation pathway is independent from the effect of immunosuppressive drugs. The data showed that 11% of transplant patients displayed very low or undetectable responses to pp65 peptide pool antigen while having sustained high responses to whole CMV particle. In addition, in all the subjects analyzed, CMI responses to CMV particle produced a statistically significant higher number of spots compared to pp65 peptide pool antigen. Rosette pre-depletion of whole blood proved to be effective in detecting CD4+ or CD8+ T-cell responses similarly to flow cytometry. Taken together, the following recommendations are suggested to optimize the CMV-ELISPOT for transplantation settings: (1) use PMA/iono as positive control; (2) whole virus particle should be used to avoid peptide-related false negative responses; (3) a rosette pre-depletion step may be useful to detect CD4+ or CD8+ T-cell responses. Copyright © 2013 Elsevier B.V. All rights reserved.

Neural dynamics in reconfigurable silicon.

PubMed

Basu, A; Ramakrishnan, S; Petre, C; Koziol, S; Brink, S; Hasler, P E

2010-10-01

A neuromorphic analog chip is presented that is capable of implementing massively parallel neural computations while retaining the programmability of digital systems. We show measurements from neurons with Hopf bifurcations and integrate and fire neurons, excitatory and inhibitory synapses, passive dendrite cables, coupled spiking neurons, and central pattern generators implemented on the chip. This chip provides a platform for not only simulating detailed neuron dynamics but also uses the same to interface with actual cells in applications such as a dynamic clamp. There are 28 computational analog blocks (CAB), each consisting of ion channels with tunable parameters, synapses, winner-take-all elements, current sources, transconductance amplifiers, and capacitors. There are four other CABs which have programmable bias generators. The programmability is achieved using floating gate transistors with on-chip programming control. The switch matrix for interconnecting the components in CABs also consists of floating-gate transistors. Emphasis is placed on replicating the detailed dynamics of computational neural models. Massive computational area efficiency is obtained by using the reconfigurable interconnect as synaptic weights, resulting in more than 50 000 possible 9-b accurate synapses in 9 mm(2).

Programmable 3D silk bone marrow niche for platelet generation ex vivo and modeling of megakaryopoiesis pathologies

PubMed Central

Di Buduo, Christian A.; Wray, Lindsay S.; Tozzi, Lorenzo; Malara, Alessandro; Chen, Ying; Ghezzi, Chiara E.; Smoot, Daniel; Sfara, Carla; Antonelli, Antonella; Spedden, Elise; Bruni, Giovanna; Staii, Cristian; De Marco, Luigi; Magnani, Mauro; Kaplan, David L.

2015-01-01

We present a programmable bioengineered 3-dimensional silk-based bone marrow niche tissue system that successfully mimics the physiology of human bone marrow environment allowing us to manufacture functional human platelets ex vivo. Using stem/progenitor cells, megakaryocyte function and platelet generation were recorded in response to variations in extracellular matrix components, surface topography, stiffness, coculture with endothelial cells, and shear forces. Millions of human platelets were produced and showed to be functional based on multiple activation tests. Using adult hematopoietic progenitor cells our system demonstrated the ability to reproduce key steps of thrombopoiesis, including alterations observed in diseased states. A critical feature of the system is the use of natural silk protein biomaterial allowing us to leverage its biocompatibility, nonthrombogenic features, programmable mechanical properties, and surface binding of cytokines, extracellular matrix components, and endothelial-derived proteins. This in turn offers new opportunities for the study of blood component production ex vivo and provides a superior tissue system for the study of pathologic mechanisms of human platelet production. PMID:25575540

Innovative financing instruments for global health 2002-15: a systematic analysis.

PubMed

Atun, Rifat; Silva, Sachin; Knaul, Felicia M

2017-07-01

Development assistance for health (DAH), the value of which peaked in 2013 and fell in 2015, is unlikely to rise substantially in the near future, increasing reliance on domestic and innovative financing sources to sustain health programmes in low-income and middle-income countries. We examined innovative financing instruments (IFIs)-financing schemes that generate and mobilise funds-to estimate the quantum of financing mobilised from 2002 to 2015. We identified ten IFIs, which mobilised US$8·9 billion (2·3% of overall DAH) in 2002-15. The funds generated by IFIs were channelled mostly through GAVI and the Global Fund, and used for programmes for new and underused vaccines, HIV/AIDS, malaria, tuberculosis, and maternal and child health. Vaccination programmes received the largest amount of funding ($2·6 billion), followed by HIV/AIDS ($1080·7 million) and malaria ($1028·9 million), with no discernible funding targeted to non-communicable diseases. Copyright © 2017 The Author(s). Published by Elsevier Ltd. This is an Open Access article under the CC BY-NC-ND 4.0 license. Published by Elsevier Ltd.. All rights reserved.

The Night Sky, The Forgotten Nature: Uncovering the Impact of One Television Programme on Astronomy Communication in Iran

NASA Astrophysics Data System (ADS)

Nazemi, P.

2017-09-01

In 2001, two brothers known as the Saffarianpour brothers started a television programme on Iranian state television called Aseman-e-shab (The Night Sky). The programme, which explores astronomy and space science, became one of the longest-running television shows in the history of Iranian television and played a major role in the public communication of science and astronomy. It inspired many of the next generation of Iranian scientists and astronomers and played a key role in the advancement of science journalism and science communication in Iranian media. This article outlines a brief history of the show and its producer and describes the role they played in Iranian society.

Developing a structured education reminiscence-based programme for staff in long-stay care facilities in Ireland.

PubMed

Cooney, Adeline; O'Shea, Eamon; Casey, Dympna; Murphy, Kathy; Dempsey, Laura; Smyth, Siobhan; Hunter, Andrew; Murphy, Edel; Devane, Declan; Jordan, Fionnuala

2013-07-01

This paper describes the steps used in developing and piloting a structured education programme - the Structured Education Reminiscence-based Programme for Staff (SERPS). The programme aimed to prepare nurses and care assistants to use reminiscence when caring for people with dementia living in long-term care. Reminiscence involves facilitating people to talk or think about their past. Structured education programmes are used widely as interventions in randomised controlled trials. However, the process of developing a structured education programme has received little attention relative to that given to evaluating the effectiveness of such programmes. This paper makes explicit the steps followed to develop the SERPS, thereby making a contribution to the methodology of designing and implementing effective structured education programmes. The approach to designing the SERPS was informed by the Van Meijel et al. (2004) model (Journal of Advanced Nursing 48, 84): (1) problem definition, (2) accumulation of building blocks for intervention design, (3) intervention design and (4) intervention validation. Grounded theory was used (1) to generate data to shape the 'building blocks' for the SERPS and (2) to explore residents, family and staff's experience of using/receiving reminiscence. Analysis of the pilot data indicated that the programme met its objective of preparing staff to use reminiscence with residents with dementia. Staff were positive both about the SERPS and the use of reminiscence with residents with dementia. This paper outlines a systematic approach to developing and validating a structured education programme. Participation in a structured education programme is more positive for staff if they are expected to actively implement what they have learnt. Ongoing support during the delivery of the programme is important for successful implementation. The incorporation of client and professional experience in the design phase is a key strength of this approach to programme design. © 2012 Blackwell Publishing Ltd.

Mentoring health researchers globally: Diverse experiences, programmes, challenges and responses.

PubMed

Cole, Donald C; Johnson, Nancy; Mejia, Raul; McCullough, Hazel; Turcotte-Tremblay, Anne-Marie; Barnoya, Joaquin; Falabella Luco, María Soledad

2016-10-01

Mentoring experiences and programmes are becoming increasingly recognised as important by those engaged in capacity strengthening in global health research. Using a primarily qualitative study design, we studied three experiences of mentorship and eight mentorship programmes for early career global health researchers based in high-income and low- and middle-income countries. For the latter, we drew upon programme materials, existing unpublished data and more formal mixed-method evaluations, supplemented by individual email questionnaire responses. Research team members wrote stories, and the team assembled and analysed them for key themes. Across the diverse experiences and programmes, key emergent themes included: great mentors inspire others in an inter-generational cascade, mentorship is transformative in personal and professional development and involves reciprocity, and finding the right balance in mentoring relationships and programmes includes responding creatively to failure. Among the challenges encountered were: struggling for more level playing fields for new health researchers globally, changing mindsets in institutions that do not have a culture of mentorship and building collaboration not competition. Mentoring networks spanning institutions and countries using multiple virtual and face-to-face methods are a potential avenue for fostering organisational cultures supporting quality mentorship in global health research.

Mentoring health researchers globally: Diverse experiences, programmes, challenges and responses

PubMed Central

Cole, Donald C.; Johnson, Nancy; Mejia, Raul; McCullough, Hazel; Turcotte-Tremblay, Anne-Marie; Barnoya, Joaquin; Falabella Luco, (María) Soledad

2016-01-01

ABSTRACT Mentoring experiences and programmes are becoming increasingly recognised as important by those engaged in capacity strengthening in global health research. Using a primarily qualitative study design, we studied three experiences of mentorship and eight mentorship programmes for early career global health researchers based in high-income and low- and middle-income countries. For the latter, we drew upon programme materials, existing unpublished data and more formal mixed-method evaluations, supplemented by individual email questionnaire responses. Research team members wrote stories, and the team assembled and analysed them for key themes. Across the diverse experiences and programmes, key emergent themes included: great mentors inspire others in an inter-generational cascade, mentorship is transformative in personal and professional development and involves reciprocity, and finding the right balance in mentoring relationships and programmes includes responding creatively to failure. Among the challenges encountered were: struggling for more level playing fields for new health researchers globally, changing mindsets in institutions that do not have a culture of mentorship and building collaboration not competition. Mentoring networks spanning institutions and countries using multiple virtual and face-to-face methods are a potential avenue for fostering organisational cultures supporting quality mentorship in global health research. PMID:26234691

Wine biotechnology in South Africa: towards a systems approach to wine science.

PubMed

Moore, John P; Divol, Benoit; Young, Philip R; Nieuwoudt, Hélène H; Ramburan, Viresh; du Toit, Maret; Bauer, Florian F; Vivier, Melané A

2008-11-01

The wine industry in South Africa is over three centuries old and over the last decade has reemerged as a significant competitor in world wine markets. The Institute for Wine Biotechnology (IWBT) was established in partnership with the Department of Viticulture and Oenology at Stellenbosch University to foster basic fundamental research in the wine sciences leading to applications in the broader wine and grapevine industries. This review focuses on the different research programmes of the Institute (grapevine, yeast and bacteria biotechnology programmes, and chemical-analytical research), commercialisation activities (SunBio) and new initiatives to integrate the various research disciplines. An important focus of future research is the Wine Science Research Niche Area programme, which connects the different research thrusts of the IWBT and of several research partners in viticulture, oenology, food science and chemistry. This 'Functional Wine-omics' programme uses a systems biology approach to wine-related organisms. The data generated within the programme will be integrated with other data sets from viticulture, oenology, analytical chemistry and the sensory sciences through chemometrics and other statistical tools. The aim of the programme is to model aspects of the wine making process, from the vineyard to the finished product.

Advanced space system analysis software. Technical, user, and programmer guide

NASA Technical Reports Server (NTRS)

Farrell, C. E.; Zimbelman, H. F.

1981-01-01

The LASS computer program provides a tool for interactive preliminary and conceptual design of LSS. Eight program modules were developed, including four automated model geometry generators, an associated mass properties module, an appendage synthesizer module, an rf analysis module, and an orbital transfer analysis module. The existing rigid body controls analysis module was modified to permit analysis of effects of solar pressure on orbital performance. A description of each module, user instructions, and programmer information are included.

[„Kids’ Skills” by Ben Furman – Description and Research Review].

PubMed

Perband, Anke; Haupts, Nadja; Rogner, Josef

2016-01-01

The article describes the programme „Kids’ Skills“ by the Finnish psychiatrist Ben Furman. „Kids’ Skills“ was developed to address behavioural issues in children. It is based on the assumption that children’s behavioural problems should not be pathologized, but can instead be corrected by learning a corresponding skill. The programme is characterised by its focus on strengths and its humorous and playful approach. The 15 steps of “Kids’ Skills” are intended to identify the specific skill, help generate a learning process and continue motivating the child. The authors describe the steps of the programme using a case study. They also address the limited number of existing studies, which have included a telephone and an online survey of practitioners using the programme, as well as case studies. The results of these studies are discussed with regard to their basis in evidence and practical relevance. Continuing research is recommended and possible implementations are suggested.

SNAP: A computer program for generating symbolic network functions

NASA Technical Reports Server (NTRS)

Lin, P. M.; Alderson, G. E.

1970-01-01

The computer program SNAP (symbolic network analysis program) generates symbolic network functions for networks containing R, L, and C type elements and all four types of controlled sources. The program is efficient with respect to program storage and execution time. A discussion of the basic algorithms is presented, together with user's and programmer's guides.

Examinations Wash Back Effects: Challenges to the Criterion Referenced Assessment Model

ERIC Educational Resources Information Center

Mogapi, M.

2016-01-01

Examinations play a central role in the educational system due to the fact that information generated from examinations is used for a variety of purposes. Critical decisions such as selection, placement and determining the instructional effectives of a programme of study all depend on data generated from examinations. Numerous research studies…

Modeling, Dynamics, Bifurcation Behavior and Stability Analysis of a DC-DC Boost Converter in Photovoltaic Systems

NASA Astrophysics Data System (ADS)

Zhioua, M.; El Aroudi, A.; Belghith, S.; Bosque-Moncusí, J. M.; Giral, R.; Al Hosani, K.; Al-Numay, M.

A study of a DC-DC boost converter fed by a photovoltaic (PV) generator and supplying a constant voltage load is presented. The input port of the converter is controlled using fixed frequency pulse width modulation (PWM) based on the loss-free resistor (LFR) concept whose parameter is selected with the aim to force the PV generator to work at its maximum power point. Under this control strategy, it is shown that the system can exhibit complex nonlinear behaviors for certain ranges of parameter values. First, using the nonlinear models of the converter and the PV source, the dynamics of the system are explored in terms of some of its parameters such as the proportional gain of the controller and the output DC bus voltage. To present a comprehensive approach to the overall system behavior under parameter changes, a series of bifurcation diagrams are computed from the circuit-level switched model and from a simplified model both implemented in PSIM© software showing a remarkable agreement. These diagrams show that the first instability that takes place in the system period-1 orbit when a primary parameter is varied is a smooth period-doubling bifurcation and that the nonlinearity of the PV generator is irrelevant for predicting this phenomenon. Different bifurcation scenarios can take place for the resulting period-2 subharmonic regime depending on a secondary bifurcation parameter. The boundary between the desired period-1 orbit and subharmonic oscillation resulting from period-doubling in the parameter space is obtained by calculating the eigenvalues of the monodromy matrix of the simplified model. The results from this model have been validated with time-domain numerical simulation using the circuit-level switched model and also experimentally from a laboratory prototype. This study can help in selecting the parameter values of the circuit in order to delimit the region of period-1 operation of the converter which is of practical interest in PV systems.

Versatile Stimulation Back-End With Programmable Exponential Current Pulse Shapes for a Retinal Visual Prosthesis.

PubMed

Maghami, Mohammad Hossein; Sodagar, Amir M; Sawan, Mohamad

2016-11-01

This paper reports on the design, implementation, and test of a stimulation back-end, for an implantable retinal prosthesis. In addition to traditional rectangular pulse shapes, the circuit features biphasic stimulation pulses with both rising and falling exponential shapes, whose time constants are digitally programmable. A class-B second generation current conveyor is used as a wide-swing, high-output-resistance stimulation current driver, delivering stimulation current pulses of up to ±96 μA to the target tissue. Duration of the generated current pulses is programmable within the range of 100 μs to 3 ms. Current-mode digital-to-analog converters (DACs) are used to program the amplitudes of the stimulation pulses. Fabricated using the IBM 130 nm process, the circuit consumes 1.5×1.5 mm 2 of silicon area. According to the measurements, the DACs exhibit DNL and INL of 0.23 LSB and 0.364 LSB, respectively. Experimental results indicate that the stimuli generator meets expected requirements when connected to electrode-tissue impedance of as high as 25 k Ω. Maximum power consumption of the proposed design is 3.4 mW when delivering biphasic rectangular pulses to the target load. A charge pump block is in charge of the upconversion of the standard 1.2-V supply voltage to ±3.3V.

Effectiveness of a universal school-based programme for preventing depression in Chinese adolescents: a quasi-experimental pilot study.

PubMed

Wong, Paul W C; Fu, King-Wa; Chan, Kim Y K; Chan, Wincy S C; Liu, Patricia M Y; Law, Yik-Wa; Yip, Paul S F

2012-12-15

Evidence of the effectiveness, rather than efficacy, of universal school-based programmes for preventing depression among adolescents is limited. This study examined the effectiveness of a universal depression prevention programme, "The Little Prince is Depressed" (LPD), which adopted the cognitive-behavioural model and aimed to reduce depressive symptoms and enhance protective factors of depression among secondary school students in Hong Kong. A quasi-experimental design was adopted for this pilot study. Thirteen classes were assigned to the intervention or control conditions according to the deliberation of the programme administrator of the four participating schools. Implementation was carried out in two phases, with a professional-led first phase and teacher-led programme second phase. LPD consisted of a 12-week school-based face-to-face programme with psycho-educational lessons and homework assignments. Students completed the programme generally showed positive development in help-seeking attitudes and self-esteem. For students who had more depressive symptoms at pre-assessment, the programme was found to be significant in enhancing cognitive-restructuring skills and support-seeking behaviours. The programme was not, however, found to be statistically significant in reducing depressive symptoms of the participants over the study period. A small sample size, a high attrition rate, and a short follow-up time frame. The LPD programme was successful in building resilience of the students in general and enhancing the cognitive-behavioural skills of students with depressive symptoms. While we did not find sufficient evidence for concluding that the LPD was effective in reducing depressive symptoms, we believe that these results highlight the challenges of implementing evidence-based practices generated from highly controlled environments in real-life settings. Copyright © 2012 Elsevier B.V. All rights reserved.

Spectral linewidth preservation in parametric frequency combs seeded by dual pumps.

PubMed

Tong, Zhi; Wiberg, Andreas O J; Myslivets, Evgeny; Kuo, Bill P P; Alic, Nikola; Radic, Stojan

2012-07-30

We demonstrate new technique for generation of programmable-pitch, wideband frequency combs with low phase noise. The comb generation was achieved using cavity-less, multistage mixer driven by two tunable continuous-wave pump seeds. The approach relies on phase-correlated continuous-wave pumps in order to cancel spectral linewidth broadening inherent to parametric comb generation. Parametric combs with over 200-nm bandwidth were obtained and characterized with respect to phase noise scaling to demonstrate linewidth preservation over 100 generated tones.

Global health diplomacy in Iraq: international relations outcomes of multilateral tuberculosis programmes.

PubMed

Kevany, Sebastian; Jaf, Payman; Workneh, Nibretie Gobezie; Abu Dalod, Mohammad; Tabena, Mohammed; Rashid, Sara; Al Hilfi, Thamer Kadum Yousif

2014-01-01

International development programmes, including global health interventions, have the capacity to make important implicit and explicit benefits to diplomatic and international relations outcomes. Conversely, in the absence of awareness of these implications, such programmes may generate associated threats. Due to heightened international tensions in conflict and post-conflict settings, greater attention to diplomatic outcomes may therefore be necessary. We examine related 'collateral' effects of Global Fund-supported tuberculosis programmes in Iraq. During site visits to Iraq conducted during 2012 and 2013 on behalf of the Global Fund to Fight AIDS, Tuberculosis and Malaria, on-site service delivery evaluations, unstructured interviews with clinical and operational staff, and programme documentary review of Global Fund-supported tuberculosis treatment and care programmes were conducted. During this process, a range of possible external or collateral international relations and diplomatic effects of global health programmes were assessed according to predetermined criteria. A range of positive diplomatic and international relations effects of Global Fund-supported programmes were observed in the Iraq setting. These included (1) geo-strategic accessibility and coverage; (2) provisions for programme sustainability and alignment; (3) contributions to nation-building and peace-keeping initiatives; (4) consistent observation of social, cultural and religious norms in intervention selection; and (5) selection of the most effective and cost-effective tuberculosis treatment and care interventions. Investments in global health programmes have valuable diplomatic, as well as health-related, outcomes, associated with their potential to prevent, mitigate or reverse international tension and hostility in conflict and post-conflict settings, provided that they adhere to appropriate criteria. The associated international presence in such regions may also contribute to peace-keeping efforts. Global health programmes may frequently produce a wider range of 'collateral benefits' that conventional monitoring and evaluation systems should be expanded to assess, in keeping with contemporary efforts to leverage development programmes from a 'global health diplomacy' perspective.

Effects of hydrocortisone treatment and whole-body irradiation on mouse lymphocyte stimulation in vitro

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruehl, H.; Vogt, W.; Ruehl, U.

Whole-body gamma irradiation was found to reduce the number of nucleated cells in the thymus and the spleen of C57B1 mice to the same extent as hydrocortisone treatment. Equal numbers of thymus and spleen cells from either hydrocortisone-treated or irradiated e cultured and stimulated with various mitogens. An increased stimulation of DNA synthesis by PHA. Con A, and PWM was found in thymus and spleen cells after hydrocortisone treatment as well as after whole-body irradiation. In contrast, the response to LPS, known as a typical B- cell mitogen, was not affected by any of the procedures. (auth)

VizieR Online Data Catalog: GTC spectra of z~2.3 quasars (Sulentic+, 2014)

NASA Astrophysics Data System (ADS)

Sulentic, J. W.; Marziani, P.; Del Olmo, A.; Dultzin, D.; Perea, J.; Negrete, C. A.

2014-09-01

Spectroscopic data for 22 intermediate redshift quasars are identified in Table 1. Actual data files are in FITS format in the spectra sub-directory. Each individual spectrum cover the spectral range 360-770 nm. Units are in wavelength in Angstrom, and specific flux in erg/s/cm2/Angstrom (pW/m3) in the observed frame (i.e., before redshift correction). Full object name (OBJECT), total exposure time (EXPTIME), number of coadded individual spectra (NUM_IMAG), and observation date (DATE-OBS) are reported as records in the FITS header of each spectrum (as in Table 2 of the paper). (2 data files).

Simulation model for a seven-phase BLDCM drive system

NASA Astrophysics Data System (ADS)

Park, Sang-Hoon; Lee, Won-Cheol; Lee, Jung-Hyo; Yu, Jae-Sung; Kim, Gyu-Sik; Won, Chung-Yuen

2007-12-01

BLDC motors have many advantages over brushed DC motors and induction motors. So, BLDC motors extend their application to many industrial fields. In this paper, the digital simulation and modeling of a 7-phase brushless DC motor have been presented. The 14-switch inverter and a 7-phase brushless DC motor drive system are simulated using hysteresis current controller and logic of switching pattern with the Boolean¡s function. Through some simulations, we found that our modeling and analysis of a 7-phase BLDCM with PWM inverter would be helpful for the further studies of the multi-phase BLDCM drive systems.

Research on Control System of Three - phase Brushless DC Motor for Electric Vehicle

NASA Astrophysics Data System (ADS)

Wang, Zhiwei; Jin, Hai; Guo, Jie; Su, Jie; Wang, Miao

2017-12-01

In order to study the three-phase brushless motor control system of electric vehicle, Freescale9S12XS128 chip is used as the control core, and the power MOSFET is used as the inverter device. The software is compiled by Codewarrior software. The speed control link adopts open-loop control, and the control chip collects the external sensor signal voltage Change control PWM signal output control three-phase brushless DC motor speed. The whole system consists of Hall position detection module, current detection module, power drive module and voltage detection module. The basic functions of three-phase brushless DC motor drive control are realized.

Tracking Control of Shape-Memory-Alloy Actuators Based on Self-Sensing Feedback and Inverse Hysteresis Compensation

PubMed Central

Liu, Shu-Hung; Huang, Tse-Shih; Yen, Jia-Yush

2010-01-01

Shape memory alloys (SMAs) offer a high power-to-weight ratio, large recovery strain, and low driving voltages, and have thus attracted considerable research attention. The difficulty of controlling SMA actuators arises from their highly nonlinear hysteresis and temperature dependence. This paper describes a combination of self-sensing and model-based control, where the model includes both the major and minor hysteresis loops as well as the thermodynamics effects. The self-sensing algorithm uses only the power width modulation (PWM) signal and requires no heavy equipment. The method can achieve high-accuracy servo control and is especially suitable for miniaturized applications. PMID:22315530

Regenerative braking system of PM synchronous motor

NASA Astrophysics Data System (ADS)

Gao, Qian; Lv, Chengxing; Zhao, Na; Zang, Hechao; Jiang, Huilue; Zhang, Zhaowen; Zhang, Fengli

2018-04-01

Permanent-magnet synchronous motor is widely adopted in many fields with the advantage of a high efficiency and a high torque density. Regenerative Braking Systems (RBS) provide an efficient method to assist PMSM system achieve better fuel economy and lowering exhaust emissions. This paper describes the design and testing of the regenerative braking systems of PMSM. The mode of PWM duty has been adjusted to control regenerative braking of PMSM using energy controller for the port-controlled Hamiltonian model. The simulation analysis indicates that a smooth control could be realized and the highest efficiency and the smallest current ripple could be achieved by Regenerative Braking Systems.

High-temperature brushless DC motor controller

DOEpatents

Cieslewski, Crzegorz; Lindblom, Scott C.; Maldonado, Frank J.; Eckert, Michael Nathan

2017-05-16

A motor control system for deployment in high temperature environments includes a controller; a first half-bridge circuit that includes a first high-side switching element and a first low-side switching element; a second half-bridge circuit that includes a second high-side switching element and a second low-side switching element; and a third half-bridge circuit that includes a third high-side switching element and a third; low-side switching element. The motor controller is arranged to apply a pulse width modulation (PWM) scheme to switch the first half-bridge circuit, second half-bridge circuit, and third half-bridge circuit to power a motor.

Restoring integrity--A grounded theory of coping with a fast track surgery programme.

PubMed

Jørgensen, Lene Bastrup; Fridlund, Bengt

2016-01-01

The aim of this study was to generate a theory conceptualizing and explaining behavioural processes involved in coping in order to identify the predominant coping types and coping type-specific features. Patients undergoing fast track procedures do not experience a higher risk of complications, readmission, or mortality. However, such programmes presuppose an increasing degree of patient involvement, placing high educational, physical, and mental demands on the patients. There is a lack of knowledge about how patients understand and cope with fast track programmes. The study design used classical grounded theory. The study used a multimodal approach with qualitative and quantitative data sets from 14 patients. Four predominant types of coping, with distinct physiological, cognitive, affective, and psychosocial features, existed among patients going through a fast track total hip replacement programme. These patients' main concern was to restore their physical and psychosocial integrity, which had been compromised by reduced function and mobility in daily life. To restore integrity they economized their mental resources, while striving to fulfil the expectations of the fast track programme. This goal was achieved by being mentally proactive and physically active. Three out of the four predominant types of coping matched the expectations expressed in the fast track programme. The non-matching behaviour was seen among the most nervous patients, who claimed the right to diverge from the programme. In theory, four predominant types of coping with distinct physiological, cognitive, affective, and psychosocial features occur among patients going through a fast track total hip arthroplasty programme.

Outreach Programmes for Education and Training: Contributions from the International Cartographic Association

NASA Astrophysics Data System (ADS)

Cartwright, W. E.; Fairbairn, D.

2012-07-01

Organisations like the International Cartographic Association champion programmes that develop and deliver education and training to cartographers and geospatial scientists, globally. This can be in the form of traditional university and training college programmes, short courses for professional and technical members of mapping agencies and as outreach initiatives to transfer knowledge about the discipline and its contemporary practices. Through its international community, the ICA undertakes the transfer of knowledge about cartography and GI Science by publishing books and special editions of journals and running workshops. Colleagues from the ICA community conduct these workshops on a volunteer basis, generally with the support of the national member organisation of ICA or the national mapping body. For example, the ICA promotes the generation of extensive publications, generally through its Commissions and Working Groups. The publications include books, journals and the ICA Newsletter. Outreach activities are especially pertinent to up skill colleagues from developing countries. Specialist programmes can be offered for professional and 'everyday' map users (from adults to children). The ICA can assist with its current programmes, designed to embrace professional and non-professional cartographers alike. This paper will address how education and outreach programmes can be supported by international associations, by offering programmes independently, or in partnership with sister associations and national and regional organisations and societies. As well, the paper will address the need to deliver education and outreach programmes not to just the professional international community, but also to map users and citizen map publishers.

Emerging models for mobilizing family support for chronic disease management: a structured review.

PubMed

Rosland, Ann-Marie; Piette, John D

2010-03-01

We identify recent models for programmes aiming to increase effective family support for chronic illness management and self-care among adult patients without significant physical or cognitive disabilities. We then summarize evidence regarding the efficacy for each model identified. Structured review of studies published in medical and psychology databases from 1990 to the present, reference review, general Web searches and conversations with family intervention experts. Review was limited to studies on conditions that require ongoing self-management, such as diabetes, chronic heart disease and rheumatologic disease. Programmes with three separate foci were identified: (1) Programmes that guide family members in setting goals for supporting patient self-care behaviours have led to improved implementation of family support roles, but have mixed success improving patient outcomes. (2) Programmes that train family in supportive communication techniques, such as prompting patient coping techniques or use of autonomy supportive statements, have successfully improved patient symptom management and health behaviours. (3) Programmes that give families tools and infrastructure to assist in monitoring clinical symptoms and medications are being conducted, with no evidence to date on their impact on patient outcomes. The next generation of programmes to improve family support for chronic disease management incorporate a variety of strategies. Future research can define optimal clinical situations for family support programmes, the most effective combinations of support strategies, and how best to integrate family support programmes into comprehensive models of chronic disease care.

How long does it take to become fit?

PubMed Central

Pearn, J

1980-01-01

To become fit an individual must generate optimal muscle strength and must develop cardiopulmonary reserve, or stamina. Physical fitness programmes require motivation, a graded series of appropriately designed exercises, and scientific surveillance. Motivation and efficiency in fitness programmes depends on early positive feedback to participants, confirming that stamina and strength are developing. A practical field experiment was performed to determine the minimum time that healthy young adults require to reach an initial plateau in objective measures of fitness. Fifty male university undergraduates were studied during an annual volunteer military training camp. Thirty had volunteered to take part in the fitness programme; the remaining 20 had initially rejected the offer but underwent the programme as part of their military training and acted as unmotivated controls. All the subjects became fit within 14 days of starting training, with objective improvement in both absolute strength and pulse recovery times. Non-motivated individuals, training with motivated individuals for 20 minutes each day, can therefore achieve levels of fitness indistinguishable from those of healthy highly motivated subjects. Fitness programmes must be carefully supervised, however, with medical examinations for those about to undergo vigorous exercise. PMID:7437862

Medical monitoring of asbestos-exposed workers: experience from Poland

PubMed Central

Szeszenia-Dąbrowska, Neonila; Wilczyńska, Urszula

2016-01-01

Abstract In Poland, the use of asbestos was banned in 1997 and asbestos plants have been closed since then. Despite their closure, cases of asbestos-related occupational diseases among former asbestos workers are still being recorded in the Central Register of Occupational Diseases. Between 2001 and 2014, there were 2726 asbestos-related illnesses, classified and reported as diseases associated with occupational exposure to asbestos. In 2000, Poland introduced a programme called Amiantus, targeted at former asbestos-processing plant workers. The programme provided periodic medical examinations to workers and free access to medications for treatment of asbestos-related illnesses. Introduction of the programme provided additional data to generate a reliable estimation of the number of asbestos-related occupational diseases, including cancer. The average latency period for asbestosis, lung cancer and mesothelioma is about 40 years so there may still be some health impact to former workers necessitating follow-up. We present the Polish experience of implementing a medical examination programme for asbestos-exposed workers and provide a list of activities to consider when planning for such a programme. PMID:27516637

Medical monitoring of asbestos-exposed workers: experience from Poland.

PubMed

Świątkowska, Beata; Szeszenia-Dąbrowska, Neonila; Wilczyńska, Urszula

2016-08-01

In Poland, the use of asbestos was banned in 1997 and asbestos plants have been closed since then. Despite their closure, cases of asbestos-related occupational diseases among former asbestos workers are still being recorded in the Central Register of Occupational Diseases. Between 2001 and 2014, there were 2726 asbestos-related illnesses, classified and reported as diseases associated with occupational exposure to asbestos. In 2000, Poland introduced a programme called Amiantus, targeted at former asbestos-processing plant workers. The programme provided periodic medical examinations to workers and free access to medications for treatment of asbestos-related illnesses. Introduction of the programme provided additional data to generate a reliable estimation of the number of asbestos-related occupational diseases, including cancer. The average latency period for asbestosis, lung cancer and mesothelioma is about 40 years so there may still be some health impact to former workers necessitating follow-up. We present the Polish experience of implementing a medical examination programme for asbestos-exposed workers and provide a list of activities to consider when planning for such a programme.

Failure detection in high-performance clusters and computers using chaotic map computations

DOEpatents

Rao, Nageswara S.

2015-09-01

A programmable media includes a processing unit capable of independent operation in a machine that is capable of executing 10.sup.18 floating point operations per second. The processing unit is in communication with a memory element and an interconnect that couples computing nodes. The programmable media includes a logical unit configured to execute arithmetic functions, comparative functions, and/or logical functions. The processing unit is configured to detect computing component failures, memory element failures and/or interconnect failures by executing programming threads that generate one or more chaotic map trajectories. The central processing unit or graphical processing unit is configured to detect a computing component failure, memory element failure and/or an interconnect failure through an automated comparison of signal trajectories generated by the chaotic maps.

Compiling global name-space programs for distributed execution

NASA Technical Reports Server (NTRS)

Koelbel, Charles; Mehrotra, Piyush

1990-01-01

Distributed memory machines do not provide hardware support for a global address space. Thus programmers are forced to partition the data across the memories of the architecture and use explicit message passing to communicate data between processors. The compiler support required to allow programmers to express their algorithms using a global name-space is examined. A general method is presented for analysis of a high level source program and along with its translation to a set of independently executing tasks communicating via messages. If the compiler has enough information, this translation can be carried out at compile-time. Otherwise run-time code is generated to implement the required data movement. The analysis required in both situations is described and the performance of the generated code on the Intel iPSC/2 is presented.

Self-Assembled DNA Tetrahedral Scaffolds for the Construction of Electrochemiluminescence Biosensor with Programmable DNA Cyclic Amplification.

PubMed

Feng, Qiu-Mei; Guo, Yue-Hua; Xu, Jing-Juan; Chen, Hong-Yuan

2017-05-24

A novel DNA tetrahedron-structured electrochemiluminescence (ECL) platform for bioanalysis with programmable DNA cyclic amplification was developed. In this work, glucose oxidase (GOD) was labeled to a DNA sequence (S) as functional conjugation (GOD-S), which could hybridize with other DNA sequences (L and P) to form GOD-S:L:P probe. In the presence of target DNA and a help DNA (A), the programmable DNA cyclic amplification was activated and released GOD-S via toehold-mediated strand displacement. Then, the obtained GOD-S was further immobilized on the DNA tetrahedral scaffolds with a pendant capture DNA and Ru(bpy) 3 2+ -conjugated silica nanoparticles (RuSi NPs) decorated on the electrode surface. Thus, the amount of GOD-S assembled on the electrode surface depended on the concentration of target DNA and GOD could catalyze glucose to generate H 2 O 2 in situ. The ECL signal of Ru(bpy) 3 2+ -TPrA system was quenched by the presence of H 2 O 2 . By integrating the programmable DNA cyclic amplification and in situ generating H 2 O 2 as Ru(bpy) 3 2+ ECL quencher, a sensitive DNA tetrahedron-structured ECL sensing platform was proposed for DNA detection. Under optimized conditions, this biosensor showed a wide linear range from 100 aM to 10 pM with a detection limit of 40 aM, indicating a promising application in DNA analysis. Furthermore, by labeling GOD to different recognition elements, the proposed strategy could be used for the detection of various targets. Thus, this programmable cascade amplification strategy not only retains the high selectivity and good capturing efficiency of tetrahedral-decorated electrode surface but also provides potential applications in the construction of ECL biosensor.

An integration programme of poverty alleviation and development with family planning.

PubMed

1997-04-01

The State Council (the central government) recently issued a Circular for Speeding Up the Integration of Poverty Alleviation and Development with the Family Planning Programme during the Ninth Five-year Plan (1996-2000). The Circular was jointly submitted by the State Family Planning Commission and the Leading Group for Poverty Alleviation and Development. The document sets the two major tasks as solving the basic needs for food and clothing of the rural destitute and the control of over-rapid growth of China's population. Practice indicates that a close Integration Programme is the best way for impoverished farmers to alleviate poverty and become better-off. Overpopulation and low educational attainments and poor health quality of population in backward areas are the major factors retarding socioeconomic development. Therefore, it is inevitable to integrate poverty alleviation with family planning. It is a path with Chinese characteristics for a balanced population and sustainable socioeconomic development. The targets of the Integration Programme are as follows: The first is that preferential policies should be worked out to guarantee family planning acceptors, especially households with an only daughter or two daughters, are the first to be helped to eradicate poverty and become well-off. They should become good examples for other rural poor in practicing fewer but healthier births, and generating family income. The second target is that the population plans for the poor counties identified by the central government and provincial governments must be fulfilled. This should contribute to breaking the vicious circle of poverty leading to more children, in turn generating more poverty. The circular demands that more efforts should focus on the training of cadres for the Integrated Programme and on services for poor family planning acceptors. full text

Strong Interaction Studies with PANDA at FAIR

NASA Astrophysics Data System (ADS)

Schönning, Karin

2016-10-01

The Facility for Antiproton and Ion Research (FAIR) in Darmstadt, Germany, provides unique possibilities for a new generation of nuclear-, hadron- and atomic physics experiments. The future PANDA experiment at FAIR will offer a broad physics programme with emphasis on different aspects of hadron physics. Understanding the strong interaction in the perturbative regime remains one of the greatest challenges in contemporary physics and hadrons provide several important keys. In these proceedings, PANDA will be presented along with some high-lights of the planned physics programme.

Advanced earth observation spacecraft computer-aided design software: Technical, user and programmer guide

NASA Technical Reports Server (NTRS)

Farrell, C. E.; Krauze, L. D.

1983-01-01

The IDEAS computer of NASA is a tool for interactive preliminary design and analysis of LSS (Large Space System). Nine analysis modules were either modified or created. These modules include the capabilities of automatic model generation, model mass properties calculation, model area calculation, nonkinematic deployment modeling, rigid-body controls analysis, RF performance prediction, subsystem properties definition, and EOS science sensor selection. For each module, a section is provided that contains technical information, user instructions, and programmer documentation.

Mechanisms of change of a novel weight loss programme provided by a third sector organisation: a qualitative interview study.

PubMed

McMahon, Naoimh E; Visram, Shelina; Connell, Louise A

2016-05-10

There is a need for theory-driven studies that explore the underlying mechanisms of change of complex weight loss programmes. Such studies will contribute to the existing evidence-base on how these programmes work and thus inform the future development and evaluation of tailored, effective interventions to tackle overweight and obesity. This study explored the mechanisms by which a novel weight loss programme triggered change amongst participants. The programme, delivered by a third sector organisation, addressed both diet and physical activity. Over a 26 week period participants engaged in three weekly sessions (education and exercise in a large group, exercise in a small group and a one-to-one education and exercise session). Novel aspects included the intensity and duration of the programme, a competitive selection process, milestone physical challenges (e.g. working up to a 5 K and 10 K walk/run during the programme), alumni support (face-to-face and online) and family attendance at exercise sessions. Data were collected through interviews with programme providers (n = 2) and focus groups with participants (n = 12). Discussions were audio-recorded, transcribed and analysed using NVivo10. Published behaviour change frameworks and behaviour change technique taxonomies were used to guide the coding process. Clients' interactions with components of the weight loss programme brought about a change in their commitment, knowledge, beliefs about capabilities and social and environmental contexts. Intervention components that generated these changes included the competitive selection process, group and online support, family involvement and overcoming milestone challenges over the 26 week programme. The mechanisms by which these components triggered change differed between participants. There is an urgent need to establish robust interventions that can support people who are overweight and obese to achieve a healthy weight and maintain this change. Third sector organisations may be a feasible alternative to private and public sector weight loss programmes. We have presented findings from one example of a novel community-based weight loss programme and identified how the programme components resulted in change amongst the participants. Further research is needed to robustly test the effectiveness, and cost-effectiveness, of this programme.

Using the patchwork text assessment as a vehicle for evaluating students' perceptions of their clinical leadership development.

PubMed

Leigh, J A; Rutherford, J; Wild, J; Cappleman, J; Hynes, C

2012-01-01

A shift in universities world wide in providing theoretical post graduate programmes of study underpinned by traditional assessment strategies to work based learning programmes supported by innovative assessment strategies is required if Higher education institutions are to effectively educate contemporary healthcare leaders. Concurrently generating the evidence to evaluate the effectiveness of educational programmes is required by commissioners of healthcare education (DH, 2010). This paper reports on the perceptions of twelve post graduate students attending a clinical leadership masters programme of their leadership development through analysis of the critical commentary provided by students as part of assessment strategy that utilised the Patchwork Text Assessment. Following a thematic content analysis six themes emerged: programme philosophy and its impact on the success of the Patchwork Text Assessment; leadership development targeted against leadership frameworks; application and applicability of learning to the students own healthcare organisation; integrating theory to practice through theoretical development and work based activities; the value of networking; and the importance of multi-professional reflective groups. This study has clearly demonstrated how the success of the Patchwork Text Assessment in promoting deep learning is determined by its integration into the overall philosophy of the programme. Concurrently systems needed to be in place to ensure that Patchwork text Assessment is operationalised effectively and embedded within the day to day management of the programme. Copyright © 2011 Elsevier Ltd. All rights reserved.

Mentoring, coaching and action learning: interventions in a national clinical leadership development programme.

PubMed

McNamara, Martin S; Fealy, Gerard M; Casey, Mary; O'Connor, Tom; Patton, Declan; Doyle, Louise; Quinlan, Christina

2014-09-01

To evaluate mentoring, coaching and action learning interventions used to develop nurses' and midwives' clinical leadership competencies and to describe the programme participants' experiences of the interventions. Mentoring, coaching and action learning are effective interventions in clinical leadership development and were used in a new national clinical leadership development programme, introduced in Ireland in 2011. An evaluation of the programme focused on how participants experienced the interventions. A qualitative design, using multiple data sources and multiple data collection methods. Methods used to generate data on participant experiences of individual interventions included focus groups, individual interviews and nonparticipant observation. Seventy participants, including 50 programme participants and those providing the interventions, contributed to the data collection. Mentoring, coaching and action learning were positively experienced by participants and contributed to the development of clinical leadership competencies, as attested to by the programme participants and intervention facilitators. The use of interventions that are action-oriented and focused on service development, such as mentoring, coaching and action learning, should be supported in clinical leadership development programmes. Being quite different to short attendance courses, these interventions require longer-term commitment on the part of both individuals and their organisations. In using mentoring, coaching and action learning interventions, the focus should be on each participant's current role and everyday practice and on helping the participant to develop and demonstrate clinical leadership skills in these contexts. © 2014 John Wiley & Sons Ltd.

Has the London 2012 Olympic Inspire Programme Inspired a Generation? A Realist View

ERIC Educational Resources Information Center

Girginov, Vassil

2016-01-01

The organisers of the 2012 London Olympics have endeavoured explicitly to use the Games to inspire a generation. This is nothing short of putting the main claim of Olympism to the test, but surprisingly the Inspire project has received virtually no scholarly scrutiny. Using an educationally-informed view of inspiration, this paper interrogates the…

Multicellular Vascularized Engineered Tissues through User-Programmable Biomaterial Photodegradation.

PubMed

Arakawa, Christopher K; Badeau, Barry A; Zheng, Ying; DeForest, Cole A

2017-10-01

A photodegradable material-based approach to generate endothelialized 3D vascular networks within cell-laden hydrogel biomaterials is introduced. Exploiting multiphoton lithography, microchannel networks spanning nearly all size scales of native human vasculature are readily generated with unprecedented user-defined 4D control. Intraluminal channel architectures of synthetic vessels are fully customizable, providing new opportunities for next-generation microfluidics and directed cell function. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hierarchical brain tissue segmentation and its application in multiple sclerosis and Alzheimer's disease

NASA Astrophysics Data System (ADS)

Lei, Tianhu; Udupa, Jayaram K.; Moonis, Gul; Schwartz, Eric; Balcer, Laura

2005-04-01

Based on Fuzzy Connectedness (FC) object delineation principles and algorithms, a hierarchical brain tissue segmentation technique has been developed for MR images. After MR image background intensity inhomogeneity correction and intensity standardization, three FC objects for cerebrospinal fluid (CSF), gray matter (GM), and white matter (WM) are generated via FC object delineation, and an intracranial (IC) mask is created via morphological operations. Then, the IC mask is decomposed into parenchymal (BP) and CSF masks, while the BP mask is separated into WM and GM masks. WM mask is further divided into pure and dirty white matter masks (PWM and DWM). In Multiple Sclerosis studies, a severe white matter lesion (LS) mask is defined from DWM mask. Based on the segmented brain tissue images, a histogram-based method has been developed to find disease-specific, image-based quantitative markers for characterizing the macromolecular manifestation of the two diseases. These same procedures have been applied to 65 MS (46 patients and 19 normal subjects) and 25 AD (15 patients and 10 normal subjects) data sets, each of which consists of FSE PD- and T2-weighted MR images. Histograms representing standardized PD and T2 intensity distributions and their numerical parameters provide an effective means for characterizing the two diseases. The procedures are systematic, nearly automated, robust, and the results are reproducible.

Economics of a reduction in smoking: case study from Heartbeat Wales.

PubMed Central

Phillips, C J; Prowle, M J

1993-01-01

STUDY OBJECTIVE--This study aims to apply economic principles and techniques in evaluating a health promotion programme. DESIGN--This study is an economic appraisal of the Heartbeat Wales no smoking intervention programme. The costs incurred over the four year period 1985-89 have been identified and estimates have been made of the likely future impact of the reduced smoking prevalence within Wales in terms of reduced morbidity and displaced mortality in three disease groups--coronary heart disease, lung cancer, and chronic bronchitis. SETTING--Wales, UK. RESULTS--The net present value of benefits is considerably greater than costs in terms of both the NHS and the economy as a whole in Wales. In addition, the net costs per life year saved shows that the programme generates additional working life years at relatively low cost. Because not all the benefits can be fully attributed to the programme 'impact rates' ranging from 100 to 10% have been applied to the level of benefits. The evidence suggests that even if only 10% of the benefits could be attributed to the programme there is still a positive net present value of benefits. The relative efficiency of this programme has not been considered here. CONCLUSION--Large scale benefits to the NHS and the economy as a whole can be derived from reductions in smoking. PMID:8350035

Understanding patient participation behaviour in studies of COPD support programmes such as pulmonary rehabilitation and self-management: a qualitative synthesis with application of theory.

PubMed

Sohanpal, Ratna; Steed, Liz; Mars, Thomas; Taylor, Stephanie J C

2015-09-17

In chronic obstructive pulmonary disease (COPD), the problem of poor patient participation in studies of self-management (SM) and pulmonary rehabilitation (PR) programmes (together referred to as COPD support programmes) is established. Understanding this problem beyond the previously reported socio-demographics and clinical factors is critical. The aim of this study was to explore factors that explain patient participation in studies of COPD support programmes. Thematic 'framework' synthesis was conducted on literature published from 1984 to 1 February 2015. Emergent themes and subthemes were mapped onto the adapted 'attitude-social influence-external barriers' and the 'self-regulation' models to produce analytical themes. Ten out of 12 studies were included: PR (n=9) and SM (n=1). Three descriptive themes with 38 subthemes were mapped onto the models' constructs, and it generated four analytical themes: 'attitude', 'social influences' and 'illness' and 'intervention representations'. The following factors influenced (1) attendance-helping oneself through health improvements, perceived control of worsening condition, perceived benefits and positive past experience of the programme, as well as perceived positive influence of professionals; (2) non-attendance-perceived negative effects and negative past experience of the programme, perceived physical/practical concerns related to attendance, perceived severity of condition/symptoms and perceived negative influence of professionals/friends; (3) dropout-no health improvements perceived after attending a few sessions of the programme, perceived severity of the condition and perceived physical/practical concerns related to attendance. Psychosocial factors including perceived practical/physical concerns related to attendance influenced patients' participation in COPD support programmes. Addressing the negative beliefs/perceptions via behaviour change interventions may help improve participation in COPD support programmes and, ultimately, patient outcomes.

Training a new generation of speech-language pathologists with competences in the management of literacy disorders and learning disabilities in Hong Kong.

PubMed

Yuen, Kevin C P

2014-01-01

One of the recent developments in the education of speech-language pathology is to include literacy disorders and learning disabilities as key training components in the training curriculum. Disorders in reading and writing are interwoven with disorders in speaking and listening, which should be managed holistically, particularly in children and adolescents. With extensive training in clinical linguistics, language disorders, and other theoretical knowledge and clinical skills, speech-language pathologists (SLPs) are the best equipped and most competent professionals to screen, identify, diagnose, and manage individuals with literacy disorders. To tackle the challenges of and the huge demand for services in literacy as well as language and learning disorders, the Hong Kong Institute of Education has recently developed the Master of Science Programme in Educational Speech-Language Pathology and Learning Disabilities, which is one of the very first speech-language pathology training programmes in Asia to blend training components of learning disabilities, literacy disorders, and social-emotional-behavioural-developmental disabilities into a developmentally and medically oriented speech-language pathology training programme. This new training programme aims to prepare a new generation of SLPs to be able to offer comprehensive support to individuals with speech, language, literacy, learning, communication, and swallowing disorders of different developmental or neurogenic origins, particularly to infants and adolescents as well as to their family and educational team. © 2015 S. Karger AG, Basel.

[The IPT integrative program of psychological therapy for schizophrenia patients: new perspectives].

PubMed

Pomini, Valentino

2004-04-01

The integrated psychological treatment for schizophrenic patients IPT is composed by six modules that can be implemented either separately or in an articulated way. In that case, the treatment begins with a cognitive remediation phase which is followed by a social skills training phase. In the first phase, exercises specifically focalize on selective attention, memory, logical reasoning, perception and communication skills. The second phase of the program offers three other modules that train other skills: 1) social skills, 2) emotional management, 3) interpersonal problem solving. The IPT program belong to the so called second generation of social skills training programmes. It has been validated by numerous controlled studies, either in its complete form or in partial forms containing only one ore more of its sub-programmes. The results of these studies are globally positive. They show that IPT is an interesting therapeutic contribution for the rehabilitation practice with schizophrenic patients. A third generation of social skills training has been elaborated on the basis of the current IPT program. These new adjunctions to the IPT tend to favour the utilization in the real life of the competencies trained in the sessions, either by adding specific homeworks, in-vivo or booster sessions, or by designating new programmes directed to specific rehabilitation objectives, such as the integration in a apartment, the management of leisure times or the return to a workplace. These new programmes have been studied. They are promising and seem to be a useful complement to the original IPT.

Real-time monitoring of enzyme-free strand displacement cascades by colorimetric assays

NASA Astrophysics Data System (ADS)

Duan, Ruixue; Wang, Boya; Hong, Fan; Zhang, Tianchi; Jia, Yongmei; Huang, Jiayu; Hakeem, Abdul; Liu, Nannan; Lou, Xiaoding; Xia, Fan

2015-03-01

The enzyme-free toehold-mediated strand displacement reaction has shown potential for building programmable DNA circuits, biosensors, molecular machines and chemical reaction networks. Here we report a simple colorimetric method using gold nanoparticles as signal generators for the real-time detection of the product of the strand displacement cascade. During the process the assembled gold nanoparticles can be separated, resulting in a color change of the solution. This assay can also be applied in complex mixtures, fetal bovine serum, and to detect single-base mismatches. These results suggest that this method could be of general utility to monitor more complex enzyme-free strand displacement reaction-based programmable systems or for further low-cost diagnostic applications.The enzyme-free toehold-mediated strand displacement reaction has shown potential for building programmable DNA circuits, biosensors, molecular machines and chemical reaction networks. Here we report a simple colorimetric method using gold nanoparticles as signal generators for the real-time detection of the product of the strand displacement cascade. During the process the assembled gold nanoparticles can be separated, resulting in a color change of the solution. This assay can also be applied in complex mixtures, fetal bovine serum, and to detect single-base mismatches. These results suggest that this method could be of general utility to monitor more complex enzyme-free strand displacement reaction-based programmable systems or for further low-cost diagnostic applications. Electronic supplementary information (ESI) available: Experimental procedures and analytical data are provided. See DOI: 10.1039/c5nr00697j

A Low Power Linear Phase Programmable Long Delay Circuit.

PubMed

Rodriguez-Villegas, Esther; Logesparan, Lojini; Casson, Alexander J

2014-06-01

A novel linear phase programmable delay is being proposed and implemented in a 0.35 μm CMOS process. The delay line consists of N cascaded cells, each of which delays the input signal by Td/N, where Td is the total line delay. The delay generated by each cell is programmable by changing a clock frequency and is also fully independent of the frequency of the input signal. The total delay hence depends only on the chosen clock frequency and the total number of cascaded cells. The minimum clock frequency is limited by the maximum time a voltage signal can effectively be held by an individual cell. The maximum number of cascaded cells will be limited by the effects of accumulated offset due to transistor mismatch, which eventually will affect the operating mode of the individual transistors in a cell. This latter limitation has however been dealt with in the topology by having an offset compensation mechanism that makes possible having a large number of cascaded cells and hence a long resulting delay. The delay line has been designed for scalp-based neural activity analysis that is predominantly in the sub-100 Hz frequency range. For these signals, the delay generated by a 31-cell cascade has been demonstrated to be programmable from 30 ms to 3 s. Measurement results demonstrate a 31 stage, 50 Hz bandwidth, 0.3 s delay that operates from a 1.1 V supply with power consumption of 270 nW.

Developing teachers' models for assessing students' competence in mathematical modelling through lesson study

NASA Astrophysics Data System (ADS)

Aydogan Yenmez, Arzu; Erbas, Ayhan Kursat; Cakiroglu, Erdinc; Alacaci, Cengiz; Cetinkaya, Bulent

2017-08-01

Applications and modelling have gained a prominent role in mathematics education reform documents and curricula. Thus, there is a growing need for studies focusing on the effective use of mathematical modelling in classrooms. Assessment is an integral part of using modelling activities in classrooms, since it allows teachers to identify and manage problems that arise in various stages of the modelling process. However, teachers' difficulties in assessing student modelling work are a challenge to be considered when implementing modelling in the classroom. Thus, the purpose of this study was to investigate how teachers' knowledge on generating assessment criteria for assessing student competence in mathematical modelling evolved through a professional development programme, which is based on a lesson study approach and modelling perspective. The data was collected with four teachers from two public high schools over a five-month period. The professional development programme included a cyclical process, with each cycle consisting of an introductory meeting, the implementation of a model-eliciting activity with students, and a follow-up meeting. The results showed that the professional development programme contributed to teachers' knowledge for generating assessment criteria on the products, and the observable actions that affect the modelling cycle.

Photonic generation of FCC-compliant UWB pulses based on modified Gaussian quadruplet and incoherent wavelength-to-time conversion

NASA Astrophysics Data System (ADS)

Mu, Hongqian; Wang, Muguang; Tang, Yu; Zhang, Jing; Jian, Shuisheng

2018-03-01

A novel scheme for the generation of FCC-compliant UWB pulse is proposed based on modified Gaussian quadruplet and incoherent wavelength-to-time conversion. The modified Gaussian quadruplet is synthesized based on linear sum of a broad Gaussian pulse and two narrow Gaussian pulses with the same pulse-width and amplitude peak. Within specific parameter range, FCC-compliant UWB with spectral power efficiency of higher than 39.9% can be achieved. In order to realize the designed waveform, a UWB generator based on spectral shaping and incoherent wavelength-to-time mapping is proposed. The spectral shaper is composed of a Gaussian filter and a programmable filter. Single-mode fiber functions as both dispersion device and transmission medium. Balanced photodetection is employed to combine linearly the broad Gaussian pulse and two narrow Gaussian pulses, and at same time to suppress pulse pedestals that result in low-frequency components. The proposed UWB generator can be reconfigured for UWB doublet by operating the programmable filter as a single-band Gaussian filter. The feasibility of proposed UWB generator is demonstrated experimentally. Measured UWB pulses match well with simulation results. FCC-compliant quadruplet with 10-dB bandwidth of 6.88-GHz, fractional bandwidth of 106.8% and power efficiency of 51% is achieved.

Digital-Analog Hybrid Scheme and Its Application to Chaotic Random Number Generators

NASA Astrophysics Data System (ADS)

Yuan, Zeshi; Li, Hongtao; Miao, Yunchi; Hu, Wen; Zhu, Xiaohua

2017-12-01

Practical random number generation (RNG) circuits are typically achieved with analog devices or digital approaches. Digital-based techniques, which use field programmable gate array (FPGA) and graphics processing units (GPU) etc. usually have better performances than analog methods as they are programmable, efficient and robust. However, digital realizations suffer from the effect of finite precision. Accordingly, the generated random numbers (RNs) are actually periodic instead of being real random. To tackle this limitation, in this paper we propose a novel digital-analog hybrid scheme that employs the digital unit as the main body, and minimum analog devices to generate physical RNs. Moreover, the possibility of realizing the proposed scheme with only one memory element is discussed. Without loss of generality, we use the capacitor and the memristor along with FPGA to construct the proposed hybrid system, and a chaotic true random number generator (TRNG) circuit is realized, producing physical RNs at a throughput of Gbit/s scale. These RNs successfully pass all the tests in the NIST SP800-22 package, confirming the significance of the scheme in practical applications. In addition, the use of this new scheme is not restricted to RNGs, and it also provides a strategy to solve the effect of finite precision in other digital systems.

Automated ILA design for synchronous sequential circuits

NASA Technical Reports Server (NTRS)

Liu, M. N.; Liu, K. Z.; Maki, G. K.; Whitaker, S. R.

1991-01-01

An iterative logic array (ILA) architecture for synchronous sequential circuits is presented. This technique utilizes linear algebra to produce the design equations. The ILA realization of synchronous sequential logic can be fully automated with a computer program. A programmable design procedure is proposed to fullfill the design task and layout generation. A software algorithm in the C language has been developed and tested to generate 1 micron CMOS layouts using the Hewlett-Packard FUNGEN module generator shell.

Hydrogen sensor

DOEpatents

Duan, Yixiang; Jia, Quanxi; Cao, Wenqing

2010-11-23

A hydrogen sensor for detecting/quantitating hydrogen and hydrogen isotopes includes a sampling line and a microplasma generator that excites hydrogen from a gas sample and produces light emission from excited hydrogen. A power supply provides power to the microplasma generator, and a spectrometer generates an emission spectrum from the light emission. A programmable computer is adapted for determining whether or not the gas sample includes hydrogen, and for quantitating the amount of hydrogen and/or hydrogen isotopes are present in the gas sample.

High precision triangular waveform generator

DOEpatents

Mueller, Theodore R.

1983-01-01

An ultra-linear ramp generator having separately programmable ascending and descending ramp rates and voltages is provided. Two constant current sources provide the ramp through an integrator. Switching of the current at current source inputs rather than at the integrator input eliminates switching transients and contributes to the waveform precision. The triangular waveforms produced by the waveform generator are characterized by accurate reproduction and low drift over periods of several hours. The ascending and descending slopes are independently selectable.

High-precision triangular-waveform generator

DOEpatents

Mueller, T.R.

1981-11-14

An ultra-linear ramp generator having separately programmable ascending and decending ramp rates and voltages is provided. Two constant current sources provide the ramp through an integrator. Switching of the current at current source inputs rather than at the integrator input eliminates switching transients and contributes to the waveform precision. The triangular waveforms produced by the waveform generator are characterized by accurate reproduction and low drift over periods of several hours. The ascending and descending slopes are independently selectable.

The economic value of an improved malaria treatment programme in Zambia: results from a contingent valuation survey.

PubMed

Masiye, Felix; Rehnberg, Clas

2005-12-15

Zambia is facing a double crisis of increasing malaria burden and dwindling capacity to deal with the endemic malaria burden. The pursuit of sustainable but equity mechanisms for financing malaria programmes is a subject of crucial policy discussion. This requires that comprehensive accounting of the economic impact of the various malaria programmes. Information on the economic value of programmes is essential in soliciting appropriate funding allocations for malaria control. This paper specifically seeks to elicit a measure of the economic benefits of an improved malaria treatment programme in Zambia. The paper also studies the equity implications in malaria treatment given that demand or malaria treatment is determined by household socio-economic status. A contingent valuation survey of about 300 Zambian households was conducted in four districts. Willingness-to-pay (WTP) was elicited for an improved treatment programme for malaria in order to generate a measure of the economic benefits of the programme. The payment card method was used in eliciting WTP bids. The study reports that malaria treatment has significant economic benefits to society. The total economic benefits of an improved treatment programme were estimated at an equivalent of USD 77 million per annum, representing about 1.8% of Zambia's GDP. The study also reports the theoretically anticipated association between WTP and several socio-economic factors. Our income elasticity of demand is positive and similar in magnitude to estimates reported in similar studies. Finally, from an equity standpoint, the constraints imposed by income and socio-economic status are discussed.

Restoring integrity—A grounded theory of coping with a fast track surgery programme

PubMed Central

Jørgensen, Lene Bastrup; Fridlund, Bengt

2016-01-01

Aims and objectives The aim of this study was to generate a theory conceptualizing and explaining behavioural processes involved in coping in order to identify the predominant coping types and coping type-specific features. Background Patients undergoing fast track procedures do not experience a higher risk of complications, readmission, or mortality. However, such programmes presuppose an increasing degree of patient involvement, placing high educational, physical, and mental demands on the patients. There is a lack of knowledge about how patients understand and cope with fast track programmes. Design The study design used classical grounded theory. Methods The study used a multimodal approach with qualitative and quantitative data sets from 14 patients. Results Four predominant types of coping, with distinct physiological, cognitive, affective, and psychosocial features, existed among patients going through a fast track total hip replacement programme. These patients’ main concern was to restore their physical and psychosocial integrity, which had been compromised by reduced function and mobility in daily life. To restore integrity they economized their mental resources, while striving to fulfil the expectations of the fast track programme. This goal was achieved by being mentally proactive and physically active. Three out of the four predominant types of coping matched the expectations expressed in the fast track programme. The non-matching behaviour was seen among the most nervous patients, who claimed the right to diverge from the programme. Conclusion In theory, four predominant types of coping with distinct physiological, cognitive, affective, and psychosocial features occur among patients going through a fast track total hip arthroplasty programme. PMID:26751199

The economic value of an improved malaria treatment programme in Zambia: results from a contingent valuation survey

PubMed Central

Masiye, Felix; Rehnberg, Clas

2005-01-01

Background Zambia is facing a double crisis of increasing malaria burden and dwindling capacity to deal with the endemic malaria burden. The pursuit of sustainable but equity mechanisms for financing malaria programmes is a subject of crucial policy discussion. This requires that comprehensive accounting of the economic impact of the various malaria programmes. Information on the economic value of programmes is essential in soliciting appropriate funding allocations for malaria control. Aims and objectives This paper specifically seeks to elicit a measure of the economic benefits of an improved malaria treatment programme in Zambia. The paper also studies the equity implications in malaria treatment given that demand or malaria treatment is determined by household socio-economic status. Methods A contingent valuation survey of about 300 Zambian households was conducted in four districts. Willingness-to-pay (WTP) was elicited for an improved treatment programme for malaria in order to generate a measure of the economic benefits of the programme. The payment card method was used in eliciting WTP bids. Findings The study reports that malaria treatment has significant economic benefits to society. The total economic benefits of an improved treatment programme were estimated at an equivalent of US$ 77 million per annum, representing about 1.8% of Zambia's GDP. The study also reports the theoretically anticipated association between WTP and several socio-economic factors. Our income elasticity of demand is positive and similar in magnitude to estimates reported in similar studies. Finally, from an equity standpoint, the constraints imposed by income and socio-economic status are discussed. PMID:16356176

Experiences on developing digital down conversion algorithms using Xilinx system generator

NASA Astrophysics Data System (ADS)

Xu, Chengfa; Yuan, Yuan; Zhao, Lizhi

2013-07-01

The Digital Down Conversion (DDC) algorithm is a classical signal processing method which is widely used in radar and communication systems. In this paper, the DDC function is implemented by Xilinx System Generator tool on FPGA. System Generator is an FPGA design tool provided by Xilinx Inc and MathWorks Inc. It is very convenient for programmers to manipulate the design and debug the function, especially for the complex algorithm. Through the developing process of DDC function based on System Generator, the results show that System Generator is a very fast and efficient tool for FPGA design.

Developing Empathetic Skills among Teachers and Learners in High Schools in Tshwane: An Inter-Generational Approach Involving People with Dementia

ERIC Educational Resources Information Center

Alant, Erna; Geyer, Stephan; Verde, Michael

2015-01-01

This article describes the implementation and outcomes of an experiential learning approach to facilitate the development of empathetic skills among teachers and learners at two high schools in Tshwane, South Africa. An inter-generational training programme, the Memory Bridge Initiative (MBI), aimed at exposing participants to interactions with…

ACPYPE - AnteChamber PYthon Parser interfacE.

PubMed

Sousa da Silva, Alan W; Vranken, Wim F

2012-07-23

ACPYPE (or AnteChamber PYthon Parser interfacE) is a wrapper script around the ANTECHAMBER software that simplifies the generation of small molecule topologies and parameters for a variety of molecular dynamics programmes like GROMACS, CHARMM and CNS. It is written in the Python programming language and was developed as a tool for interfacing with other Python based applications such as the CCPN software suite (for NMR data analysis) and ARIA (for structure calculations from NMR data). ACPYPE is open source code, under GNU GPL v3, and is available as a stand-alone application at http://www.ccpn.ac.uk/acpype and as a web portal application at http://webapps.ccpn.ac.uk/acpype. We verified the topologies generated by ACPYPE in three ways: by comparing with default AMBER topologies for standard amino acids; by generating and verifying topologies for a large set of ligands from the PDB; and by recalculating the structures for 5 protein-ligand complexes from the PDB. ACPYPE is a tool that simplifies the automatic generation of topology and parameters in different formats for different molecular mechanics programmes, including calculation of partial charges, while being object oriented for integration with other applications.

Theory and implementation of a very high throughput true random number generator in field programmable gate array

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Yonggang, E-mail: wangyg@ustc.edu.cn; Hui, Cong; Liu, Chong

The contribution of this paper is proposing a new entropy extraction mechanism based on sampling phase jitter in ring oscillators to make a high throughput true random number generator in a field programmable gate array (FPGA) practical. Starting from experimental observation and analysis of the entropy source in FPGA, a multi-phase sampling method is exploited to harvest the clock jitter with a maximum entropy and fast sampling speed. This parametrized design is implemented in a Xilinx Artix-7 FPGA, where the carry chains in the FPGA are explored to realize the precise phase shifting. The generator circuit is simple and resource-saving,more » so that multiple generation channels can run in parallel to scale the output throughput for specific applications. The prototype integrates 64 circuit units in the FPGA to provide a total output throughput of 7.68 Gbps, which meets the requirement of current high-speed quantum key distribution systems. The randomness evaluation, as well as its robustness to ambient temperature, confirms that the new method in a purely digital fashion can provide high-speed high-quality random bit sequences for a variety of embedded applications.« less

Theory and implementation of a very high throughput true random number generator in field programmable gate array.

PubMed

Wang, Yonggang; Hui, Cong; Liu, Chong; Xu, Chao

2016-04-01

The contribution of this paper is proposing a new entropy extraction mechanism based on sampling phase jitter in ring oscillators to make a high throughput true random number generator in a field programmable gate array (FPGA) practical. Starting from experimental observation and analysis of the entropy source in FPGA, a multi-phase sampling method is exploited to harvest the clock jitter with a maximum entropy and fast sampling speed. This parametrized design is implemented in a Xilinx Artix-7 FPGA, where the carry chains in the FPGA are explored to realize the precise phase shifting. The generator circuit is simple and resource-saving, so that multiple generation channels can run in parallel to scale the output throughput for specific applications. The prototype integrates 64 circuit units in the FPGA to provide a total output throughput of 7.68 Gbps, which meets the requirement of current high-speed quantum key distribution systems. The randomness evaluation, as well as its robustness to ambient temperature, confirms that the new method in a purely digital fashion can provide high-speed high-quality random bit sequences for a variety of embedded applications.

Generating an AC amplitude magnetic flux density value up to 150 μT at a frequency up to 100 kHz

NASA Astrophysics Data System (ADS)

Ulvr, Michal; Polonský, Jakub

2017-05-01

AC magnetic field analyzers with a triaxial coil probe are widely used by health and safety professionals, in manufacturing, and in service industries. For traceable calibration of these analyzers, it is important to be able to generate a stable, homogeneous reference AC magnetic flux density (MFD). In this paper, the generating of AC amplitude MFD value of 150 μT by single-layer Helmholtz type solenoid, described in previous work, was expanded up to a frequency of 100 kHz using the effect of serial resonance. A programmable capacitor array has been developed with a range of adjustable values from 50 pF to 51225 pF. In addition, the multi-layer search coil with a nominal area turns value of 1.3m2, used for adjusting AC MFD in the solenoid, has been modified by a transimpedance amplifier for use in a wider frequency range than up to 3 kHz. The possibility of using the programmable capacitor array up to 150 kHz has also been tested. An AC amplitude MFD value of 150 μT can be generated with expanded uncertainty better than 0.6% up to 100 kHz.

Design Methodology of an Equalizer for Unipolar Non Return to Zero Binary Signals in the Presence of Additive White Gaussian Noise Using a Time Delay Neural Network on a Field Programmable Gate Array

PubMed Central

Pérez Suárez, Santiago T.; Travieso González, Carlos M.; Alonso Hernández, Jesús B.

2013-01-01

This article presents a design methodology for designing an artificial neural network as an equalizer for a binary signal. Firstly, the system is modelled in floating point format using Matlab. Afterward, the design is described for a Field Programmable Gate Array (FPGA) using fixed point format. The FPGA design is based on the System Generator from Xilinx, which is a design tool over Simulink of Matlab. System Generator allows one to design in a fast and flexible way. It uses low level details of the circuits and the functionality of the system can be fully tested. System Generator can be used to check the architecture and to analyse the effect of the number of bits on the system performance. Finally the System Generator design is compiled for the Xilinx Integrated System Environment (ISE) and the system is described using a hardware description language. In ISE the circuits are managed with high level details and physical performances are obtained. In the Conclusions section, some modifications are proposed to improve the methodology and to ensure portability across FPGA manufacturers.

Determination of quality television programmes based on sentiment analysis on Twitter

NASA Astrophysics Data System (ADS)

Amalia, A.; Oktinas, W.; Aulia, I.; Rahmat, R. F.

2018-03-01

Public sentiment from social media like Twitter can be used as one of the indicators to determine the quality of TV Programmes. In this study, we implemented information extraction on Twitter by using sentiment analysis method to assess the quality of TV Programmes. The first stage of this study is pre-processing which consists of cleansing, case folding, tokenizing, stop-word removal, stemming, and redundancy filtering. The next stage is weighting process for every single word by using TF-IDF method. The last step of this study is the sentiment classification process which is divided into three sentiment category which is positive, negative and neutral. We classify the TV programmes into several categories such as news, children, or films/soap operas. We implemented an improved k-nearest neighbor method in classification 4000 twitter status, for four biggest TV stations in Indonesia, with ratio 70% data for training and 30% of data for the testing process. The result obtained from this research generated the highest accuracy with k=10 as big as 90%.

Development of a programmable standard of ultra-low capacitance values.

PubMed

Khan, M S; Séron, O; Thuillier, G; Thévenot, O; Gournay, P; Piquemal, F

2017-05-01

A set of ultra-low value capacitance standards together with a programmable coaxial multiplexer (mux) have been developed. The mux allows the connection of these capacitances in parallel configuration and they together form the programmable capacitance standard. It is capable of producing decadic standard capacitances from 10 aF to at least 0.1 pF, which are later used to calibrate commercial precision capacitance bridges. This paper describes the realization and the characterization of this standard together with results obtained during the calibration of Andeen-Hagerling AH2700A bridges with a maximum uncertainty of 0.8 aF for all the capacitances generated ranging from 10 aF to 0.1 pF, at 1 kHz. These latter could be then integrated to functionalized AFMs or probe stations for quantitative capacitance measurements. Sources of uncertainties of the programmable capacitance standard, such as parasitic effects due to stray impedances, are evaluated and a method to overcome these hindrances is also discussed.

Cost and impact of a quality improvement programme in mental health services.

PubMed

Beecham, Jennifer; Ramsay, Angus; Gordon, Kate; Maltby, Sophie; Walshe, Kieran; Shaw, Ian; Worrall, Adrian; King, Sarah

2010-04-01

To estimate the cost and impact of a centrally-driven quality improvement initiative in four UK mental health communities. Total costs in year 1 were identified using documentation, a staff survey, semi-structured interviews and discussion groups. Few outcome data were collected within the programme so thematic analysis was used to identify the programme's impact within its five broad underlying principles. The survey had a 40% response. Total costs ranged between pound164,000 and pound458,000 per site, plus staff time spent on workstreams. There was a very hazy view of the resources absorbed and poor recording of expenditure and activity. The initiative generated little demonstrable improvements in service quality but some participants reported changes in attitudes. Given the difficult contexts, short time-scales and capacity constraints, the programme's lack of impact is not surprising. It may, however, represent a worthwhile investment in cultural change which might facilitate improvements in how services are delivered.

Programmable diagnostic devices made from paper and tape.

PubMed

Martinez, Andres W; Phillips, Scott T; Nie, Zhihong; Cheng, Chao-Min; Carrilho, Emanuel; Wiley, Benjamin J; Whitesides, George M

2010-10-07

This paper describes three-dimensional microfluidic paper-based analytical devices (3-D microPADs) that can be programmed (postfabrication) by the user to generate multiple patterns of flow through them. These devices are programmed by pressing single-use 'on' buttons, using a stylus or a ballpoint pen. Pressing a button closes a small space (gap) between two vertically aligned microfluidic channels, and allows fluids to wick from one channel to the other. These devices are simple to fabricate, and are made entirely out of paper and double-sided adhesive tape. Programmable devices expand the capabilities of microPADs and provide a simple method for controlling the movement of fluids in paper-based channels. They are the conceptual equivalent of field-programmable gate arrays (FPGAs) widely used in electronics.

Signal conditioning units for vibration measurement in HUMS

NASA Astrophysics Data System (ADS)

Wu, Kaizhi; Liu, Tingting; Yu, Zirong; Chen, Lijuan; Huang, Xinjie

2018-03-01

A signal conditioning units for vibration measurement in HUMS is proposed in the paper. Due to the frequency of vibrations caused by components in helicopter are different, two steps amplifier and programmable anti-aliasing filter are designed to meet the measurement of different types of helicopter. Vibration signals are converted into measurable electrical signals combing with ICP driver firstly. Then pre-amplifier and programmable gain amplifier is applied to magnify the weak electrical signals. In addition, programmable anti-aliasing filter is utilized to filter the interference of noise. The units were tested using function signal generator and oscilloscope. The experimental results have demonstrated the effectiveness of our proposed method in quantitatively and qualitatively. The method presented in this paper can meet the measurement requirement for different types of helicopter.

Complex adaptive systems: a tool for interpreting responses and behaviours.

PubMed

Ellis, Beverley

2011-01-01

Quality improvement is a priority for health services worldwide. There are many barriers to implementing change at the locality level and misinterpreting responses and behaviours can effectively block change. Electronic health records will influence the means by which knowledge and information are generated and sustained among those operating quality improvement programmes. To explain how complex adaptive system (CAS) theory provides a useful tool and new insight into the responses and behaviours that relate to quality improvement programmes in primary care enabled by informatics. Case studies in two English localities who participated in the implementation and development of quality improvement programmes. The research strategy included purposefully sampled case studies, conducted within a social constructionist ontological perspective. Responses and behaviours of quality improvement programmes in the two localities include both positive and negative influences associated with a networked model of governance. Pressures of time, resources and workload are common issues, along with the need for education and training about capturing, coding, recording and sharing information held within electronic health records to support various information requirements. Primary care informatics enables information symmetry among those operating quality improvement programmes by making some aspects of care explicit, allowing consensus about quality improvement priorities and implementable solutions.

A software framework for pipelined arithmetic algorithms in field programmable gate arrays

NASA Astrophysics Data System (ADS)

Kim, J. B.; Won, E.

2018-03-01

Pipelined algorithms implemented in field programmable gate arrays are extensively used for hardware triggers in the modern experimental high energy physics field and the complexity of such algorithms increases rapidly. For development of such hardware triggers, algorithms are developed in C++, ported to hardware description language for synthesizing firmware, and then ported back to C++ for simulating the firmware response down to the single bit level. We present a C++ software framework which automatically simulates and generates hardware description language code for pipelined arithmetic algorithms.

Computer-aided programming for message-passing system; Problems and a solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, M.Y.; Gajski, D.D.

1989-12-01

As the number of processors and the complexity of problems to be solved increase, programming multiprocessing systems becomes more difficult and error-prone. Program development tools are necessary since programmers are not able to develop complex parallel programs efficiently. Parallel models of computation, parallelization problems, and tools for computer-aided programming (CAP) are discussed. As an example, a CAP tool that performs scheduling and inserts communication primitives automatically is described. It also generates the performance estimates and other program quality measures to help programmers in improving their algorithms and programs.

Global health diplomacy investments in Afghanistan: adaptations and outcomes of global fund malaria programs.

PubMed

Kevany, Sebastian; Sahak, Omar; Workneh, Nibretie Gobezie; Saeedzai, Sayed Ataullah

2014-01-01

Global health programmes require extensive adaptation for implementation in conflict and post-conflict settings. Without such adaptations, both implementation success and diplomatic, international relations and other indirect outcomes may be threatened. Conversely, diplomatic successes may be made through flexible and responsive programmes. We examine adaptations and associated outcomes for malaria treatment and prevention programmes in Afghanistan. In conjunction with the completion of monitoring and evaluation activities for the Global Fund to Fight AIDS, Tuberculosis and Malaria, we reviewed adaptations to the structure, design, selection, content and delivery of malaria-related interventions in Afghanistan. Interviews were conducted with programme implementers, service delivery providers, government representatives and local stakeholders, and site visits to service delivery points were completed. Programmes for malaria treatment and prevention require a range of adaptations for successful implementation in Afghanistan. These include (1) amendment of educational materials for rural populations, (2) religious awareness in gender groupings for health educational interventions, (3) recruitment of local staff, educated in languages and customs, for both quality assurance and service delivery, (4) alignment with diplomatic principles and, thereby, avoidance of confusion with broader strategic and military initiatives and (5) amendments to programme 'branding' procedures. The absence of provision for these adaptations made service delivery excessively challenging and increased the risk of tension between narrow programmatic and broader diplomatic goals. Conversely, adapted global health programmes displayed a unique capacity to access potentially extremist populations and groups in remote regions otherwise isolated from international activities. A range of diplomatic considerations when delivering global health programmes in conflict and post-conflict settings are required in order to ensure that health gains are not offset by broader international relations losses through challenges to local cultural, religious and social norms, as well as in order to ensure the security of programme staff. Conversely, when global health programmes are delivered with international relations considerations in mind, they have the potential to generate unquantified diplomatic outcomes.

UK to train 100 PhD students in data science

NASA Astrophysics Data System (ADS)

Allen, Michael

2017-12-01

A new PhD programme to develop techniques to handle the vast amounts of data being generated by experiments and facilities has been launched by the UK's Science and Technology Facilities Council (STFC).

A Temperature-Hardened Sensor Interface with a 12-Bit Digital Output Using a Novel Pulse Width Modulation Technique

PubMed Central

Badets, Franck; Nouet, Pascal; Masmoudi, Mohamed

2018-01-01

A fully integrated sensor interface for a wide operational temperature range is presented. It translates the sensor signal into a pulse width modulated (PWM) signal that is then converted into a 12-bit digital output. The sensor interface is based on a pair of injection locked oscillators used to implement a differential time-domain architecture with low sensitivity to temperature variations. A prototype has been fabricated using a 180 nm partially depleted silicon-on-insulator (SOI) technology. Experimental results demonstrate a thermal stability as low as 65 ppm/°C over a large temperature range from −20 °C up to 220 °C. PMID:29621171