Science.gov

Sample records for quality assurance test

  1. Quality assurance of absorbed energy in Charpy impact test

    NASA Astrophysics Data System (ADS)

    Rocha, C. L. F.; Fabricio, D. A. K.; Costa, V. M.; Reguly, A.

    2016-07-01

    In order to ensure the quality assurance and comply with standard requirements, an intralaboratory study has been performed for impact Charpy tests, involving two operators. The results based on ANOVA (Analysis of Variance) and Normalized Error statistical techniques pointed out that the execution of the tests is appropriate, because the implementation of quality assurance methods showed acceptable results.

  2. Quality Assurance.

    ERIC Educational Resources Information Center

    Massachusetts Career Development Inst., Springfield.

    This booklet is one of six texts from a workplace literacy curriculum designed to assist learners in facing the increased demands of the workplace. The booklet contains five sections that cover the following topics: (1) importance of reliability; (2) meaning of quality assurance; (3) historical development of quality assurance; (4) statistical…

  3. Quality assurance

    SciTech Connect

    Gillespie, B.M.; Gleckler, B.P.

    1995-06-01

    This section of the 1994 Hanford Site Environmental Report summarizes the quality assurance and quality control practices of Hanford Site environmental monitoring and surveillance programs. Samples are analyzed according to documented standard analytical procedures. This section discusses specific measures taken to ensure quality in project management, sample collection, and analytical results.

  4. A Systems Engineering Approach to Quality Assurance for Aerospace Testing

    NASA Technical Reports Server (NTRS)

    Shepherd, Christena C.

    2015-01-01

    On the surface, it appears that AS91001 has little to say about how to apply a Quality Management System (QMS) to major aerospace test programs (or even smaller ones). It also appears that there is little in the quality engineering Body of Knowledge (BOK)2 that applies to testing, unless it is nondestructive examination (NDE), or some type of lab or bench testing associated with the manufacturing process. However, if one examines: a) how the systems engineering (SE) processes are implemented throughout a test program; and b) how these SE processes can be mapped to the requirements of AS9100, a number of areas for involvement of the quality professional are revealed. What often happens is that quality assurance during a test program is limited to inspections of the test article; what could be considered a manufacturing al fresco approach. This limits the quality professional and is a disservice to the programs and projects, since there are a number of ways that quality can enhance critical processes, and support efforts to improve risk reduction, efficiency and effectiveness.

  5. Assuring quality.

    PubMed

    Eaton, K A; Reynolds, P A; Mason, R; Cardell, R

    2008-08-09

    All those involved in education have a strong motivation to ensure that all its aspects, including content and teaching practice, are of the highest standard. This paper describes how agencies such as the Quality Assurance Agency for Higher Education (QAA) and the General Dental Council (GDC) have established frameworks and specifications to monitor the quality of education provided in dental schools and other institutes that provide education and training for dentists and dental care professionals (DCPs). It then considers quality issues in programme and course development, techniques for assessing the quality of education, including content and presentation, and the role of students. It goes on to review the work that has been done in developing quality assessment for distance learning in dentistry. It concludes that, to date, much of the work on quality applies to education as a whole and that the assessment of the quality of e-learning in dentistry is in its infancy.

  6. Current quality assurance concepts and considerations for quality control of in-clinic biochemistry testing.

    PubMed

    Lester, Sally; Harr, K E; Rishniw, Mark; Pion, Paul

    2013-01-15

    Quality assurance is an implied concept inherent in every consumer's purchase of a product or service. In laboratory testing, quality assurance encompasses preanalytic (sampling, transport, and handling prior to testing), analytic (measurement), and postanalytic (reporting and interpretation) factors. Quality-assurance programs require that procedures are in place to detect errors in all 3 components and that the procedures are characterized by both documentation and correction of errors. There are regulatory bodies that provide mandatory standards for and regulation of human medical laboratories. No such regulations exist for veterinary laboratory testing. The American Society for Veterinary Clinical Pathology (ASVCP) Quality Assurance and Laboratory Standards Committee was formed in 1996 in response to concerns of ASVCP members about quality assurance and quality control in laboratories performing veterinary testing. Guidelines for veterinary laboratory testing have been developed by the ASVCP. The purpose of this report was to provide an overview of selected quality-assurance concepts and to provide recommendations for quality control for in-clinic biochemistry testing in general veterinary practice.

  7. Quality Assurance Protocol for AFCI Advanced Structural Materials Testing

    SciTech Connect

    Busby, Jeremy T

    2009-05-01

    The objective of this letter is to inform you of recent progress on the development of advanced structural materials in support of advanced fast reactors and AFCI. As you know, the alloy development effort has been initiated in recent months with the procurement of adequate quantities of the NF616 and HT-UPS alloys. As the test alloys become available in the coming days, mechanical testing, evaluation of optimizing treatments, and screening of environmental effects will be possible at a larger scale. It is therefore important to establish proper quality assurance protocols for this testing effort in a timely manner to ensure high technical quality throughout testing. A properly implemented quality assurance effort will also enable preliminary data taken in this effort to be qualified as NQA-1 during any subsequent licensing discussions for an advanced design or actual prototype. The objective of this report is to describe the quality assurance protocols that will be used for this effort. An essential first step in evaluating quality protocols is assessing the end use of the data. Currently, the advanced structural materials effort is part of a long-range, basic research and development effort and not, as yet, involved in licensing discussions for a specific reactor design. After consultation with Mark Vance (an ORNL QA expert) and based on the recently-issued AFCI QA requirements, the application of NQA-1 quality requirements will follow the guidance provided in Part IV, Subpart 4.2 of the NQA-1 standard (Guidance on Graded Application of QA for Nuclear-Related Research and Development). This guidance mandates the application of sound scientific methodology and a robust peer review process in all phases, allowing for the data to be qualified for use even if the programmatic mission changes to include licensing discussions of a specific design or prototype. ORNL has previously implemented a QA program dedicated to GNEP activities and based on an appropriately graded

  8. RAVEN Quality Assurance Activities

    SciTech Connect

    Cogliati, Joshua Joseph

    2015-09-01

    This report discusses the quality assurance activities needed to raise the Quality Level of Risk Analysis in a Virtual Environment (RAVEN) from Quality Level 3 to Quality Level 2. This report also describes the general RAVEN quality assurance activities. For improving the quality, reviews of code changes have been instituted, more parts of testing have been automated, and improved packaging has been created. For upgrading the quality level, requirements have been created and the workflow has been improved.

  9. A Systems Engineering Approach to Quality Assurance for Aerospace Testing

    NASA Technical Reports Server (NTRS)

    Shepherd, Christena C.

    2014-01-01

    On the surface, it appears that AS9100 has little to say about how to apply a Quality Management System (QMS) to major aerospace test programs (or even smaller ones). It also appears that there is little in the quality engineering Body of Knowledge (BOK) that applies to testing, unless it is nondestructive examination (NDE), or some type of lab or bench testing associated with the manufacturing process. However, if one examines: a) how the systems engineering (SE) processes are implemented throughout a test program; and b) how these SE processes can be mapped to the requirements of AS9100, a number of areas for involvement of the quality professional are revealed. What often happens is that quality assurance during a test program is limited to inspections of the test article; what could be considered a manufacturing al fresco approach. This limits the quality professional and is a disservice to the programs and projects, since there are a number of ways that quality can enhance critical processes, and support efforts to improve risk reduction, efficiency and effectiveness. The Systems Engineering (SE) discipline is widely used in aerospace to ensure the progress from Stakeholder Expectations (the President, Congress, the taxpayers) to a successful, delivered product or service. Although this is well known, what is not well known is that these same SE processes are implemented in varying complexity, to prepare for and implement test projects that support research, development, verification and validation, qualification, and acceptance test projects. Although the test organization's terminology may vary from the SE terminology, and from one test service provider to another, the basic process is followed by successful, reliable testing organizations. For this analysis, NASA Procedural Requirements (NPR) 7123.1, NASA Systems Engineering Processes and Requirements is used to illustrate the SE processes that are used for major aerospace testing. Many of these processes

  10. Development and Testing of a Nuclear Quality Assurance/Quality Control Technician Curriculum. Final Report.

    ERIC Educational Resources Information Center

    Espy, John; And Others

    A project was conducted to field test selected first- and second-year courses in a postsecondary nuclear quality assurance/quality control (QA/QC) technician curriculum and to develop the teaching/learning modules for seven technical specialty courses remaining in the QA/QC technician curriculum. The field testing phase of the project involved the…

  11. Objective performance testing and quality assurance of medical ultrasound equipment.

    PubMed

    Thijssen, Johan M; Weijers, Gert; de Korte, Chris L

    2007-03-01

    There is an urgent need for a measurement protocol and software analysis for objective testing of the imaging performance of medical ultrasound equipment from a user's point of view. Methods for testing of imaging performance were developed. Simple test objects were used, which have a long life expectancy. First, the elevational focus (slice thickness) of the transducer was estimated and the in-plane transmit focus was positioned at the same depth. Next, the postprocessing look-up-table (LUT) was measured and linearized. The tests performed were echo level dynamic range (dB), contrast resolution (i.e., gamma of display, number of gray levels/dB) and sensitivity, overall system sensitivity, lateral sensitivity profile, dead zone, spatial resolution and geometric conformity of display. The concept of a computational observer was used to define the lesion signal-to-noise ratio, SNR(L) (or Mahalanobis distance), as a measure for contrast sensitivity. All the measurements were made using digitized images and quantified by objective means, i.e., by image analysis. The whole performance measurement protocol, as well as the quantitative measurements, have been implemented in software. An extensive data-base browser was implemented from which analysis of the images can be started and reports generated. These reports contain all the information about the measurements, such as graphs, images and numbers. The approach of calibrating the gamma by using a linearized LUT was validated by processing simultaneously acquired rf data. The contrast resolution and echo level of the rf data had to be compressed by a factor of two and amplified by a gain factor corresponding to 12 dB. This resulted in contrast curves that were practically identical to those obtained from DICOM image data. The effects of changing the transducer center frequency on the spatial resolution and contrast sensitivity were estimated to illustrate the practical usefulness of the developed approach of quality

  12. An oscillating sweeping gap test for VMAT quality assurance.

    PubMed

    Bhagwat, Mandar S; Han, Zhaohui; Ng, Sook Kien; Zygmanski, Piotr

    2010-09-07

    The objective of this study was to develop an oscillating sweeping gap test for volumetric modulated arc therapy (VMAT) quality assurance (QA). A novel test was designed and used to simultaneously determine uncertainties associated with linac performance, dose calculation and dosimetric MLC parameters during VMAT delivery. Delivered doses were measured with Matrixx, ionization chamber A12 and EDR2 films, and compared to calculations from the treatment planning system (TPS) Eclipse. A new gantry and MLC motion pattern, called here 'oscillating sweeping gap', is developed as an extension of the standard sweeping gap MLC pattern developed for IMRT QA. Specifically, in the oscillating sweeping gap test, a uniform MLC gap is moving repeatedly back and forth across the field at a constant speed during a full rotation of the gantry. The dose distribution generated by the combined gantry and MLC motion pattern is designed to be quasi-uniform within a cylindrical target volume with a sharp penumbra. The test design allows for an easy detection of dose errors as deviations from the uniform background. MLC gap sizes, gantry and MLC speeds and monitor units (MU) are selected according to a formula determining the magnitude of dose delivered to the target. Both measured and calculated dose distributions were analyzed as a function of the number of control points in the TPS, MLC gap size and magnitude of the gantry angle error. Dose calculation errors due to the insufficient number of control points in the gantry and MLC motion pattern appear as streak artifacts. The magnitude of these artifacts is increasing with the decreased number of control points, and with the decreased MLC gap size. The spatial distribution of dose errors due to the gantry angle errors (unsteady rocking motion) appears as high-frequency noise for higher wobble frequencies and as large hot/cold spots for lower wobble frequencies. The actual MLC leaf position as a function of time (or the gantry angle

  13. An oscillating sweeping gap test for VMAT quality assurance

    NASA Astrophysics Data System (ADS)

    Bhagwat, Mandar S.; Han, Zhaohui; Kien Ng, Sook; Zygmanski, Piotr

    2010-09-01

    The objective of this study was to develop an oscillating sweeping gap test for volumetric modulated arc therapy (VMAT) quality assurance (QA). A novel test was designed and used to simultaneously determine uncertainties associated with linac performance, dose calculation and dosimetric MLC parameters during VMAT delivery. Delivered doses were measured with Matrixx™, ionization chamber A12 and EDR2™ films, and compared to calculations from the treatment planning system (TPS) Eclipse™. A new gantry and MLC motion pattern, called here 'oscillating sweeping gap', is developed as an extension of the standard sweeping gap MLC pattern developed for IMRT QA. Specifically, in the oscillating sweeping gap test, a uniform MLC gap is moving repeatedly back and forth across the field at a constant speed during a full rotation of the gantry. The dose distribution generated by the combined gantry and MLC motion pattern is designed to be quasi-uniform within a cylindrical target volume with a sharp penumbra. The test design allows for an easy detection of dose errors as deviations from the uniform background. MLC gap sizes, gantry and MLC speeds and monitor units (MU) are selected according to a formula determining the magnitude of dose delivered to the target. Both measured and calculated dose distributions were analyzed as a function of the number of control points in the TPS, MLC gap size and magnitude of the gantry angle error. Dose calculation errors due to the insufficient number of control points in the gantry and MLC motion pattern appear as streak artifacts. The magnitude of these artifacts is increasing with the decreased number of control points, and with the decreased MLC gap size. The spatial distribution of dose errors due to the gantry angle errors (unsteady rocking motion) appears as high-frequency noise for higher wobble frequencies and as large hot/cold spots for lower wobble frequencies. The actual MLC leaf position as a function of time (or the gantry

  14. Underground Test Area Quality Assurance Project Plan Nevada National Security Site, Nevada, Revision 0

    SciTech Connect

    Irene Farnham

    2011-05-01

    This Quality Assurance Project Plan (QAPP) provides the overall quality assurance (QA) program requirements and general quality practices to be applied to the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Underground Test Area (UGTA) Sub-Project (hereafter the Sub-Project) activities. The requirements in this QAPP are consistent with DOE Order 414.1C, Quality Assurance (DOE, 2005); U.S. Environmental Protection Agency (EPA) Guidance for Quality Assurance Project Plans for Modeling (EPA, 2002); and EPA Guidance on the Development, Evaluation, and Application of Environmental Models (EPA, 2009). The QAPP Revision 0 supersedes DOE--341, Underground Test Area Quality Assurance Project Plan, Nevada Test Site, Nevada, Revision 4.

  15. Integrated quality assurance for assembly and testing of complex structures

    NASA Astrophysics Data System (ADS)

    von Kopylow, Christoph; Bothe, Thorsten; Elandaloussi, Frank; Kalms, Michael; Jüptner, Werner

    2005-11-01

    Modern production processes are directed by properties of the components to be manufactured. These components have different sizes, functionalities, high assembly complexity and high security requirements. The increasing requirements during the manufacturing of complex products like cars and aircrafts demand new solutions for the quality assurance - especially for the production at different places. The main focus is to find a measurement strategy that is cost effective, flexible and adaptive. That means a clear definition of the measurement problem, the measurement with adapted resolution, the data preparation and evaluation and support during measurement and utilisation of the results directly in the production. In this paper we describe flexible measurement devices on example of three different techniques: fringe projection, fringe reflection and shearography. These techniques allow the detection of surface and subsurface defects like bumps, dents and delaminations with high resolution. The defects can be optically mapped onto the object's surface. Results are demonstrated with big components taken from automotive and aircraft production. We will point out the most important adaptations of the systems to realize miniaturized, robust and mobile devices for the quality assurance in an industrial environment. Additionally the implementation into a Mobile Maintenance and Control structure is demonstrated.

  16. Use of computers in quality assurance of laboratory testing.

    PubMed

    Tan, I K; Jacob, E; Lim, S H

    1990-09-01

    Implementation of comprehensive internal quality control programmes and participation in external quality assessment schemes to monitor analytical performance of laboratory tests have been widely accepted as an essential and integral part of good laboratory practice. As these programmes involve a great deal of repetitive statistical calculations and graphic presentation of data on quality control materials, many laboratories and practically all organisers of inter-laboratory quality assessment schemes increasingly rely on computers to handle the burdensome processing of data and to provide timely feedback in a manner that is easily understood and readily interpreted by analytical staff. However, in spite of the best effort to ensure reliable analytical performance, spurious and misleading results can still occur as a result of non-analytical errors which are not readily detected by methods designed to monitor the quality of analytical process. The use of sophisticated computer system has enabled our laboratory to check for the existence of some of these errors. This paper describes the application of computers in a variety of internal and external quality assessment programmes and demonstrates the usefulness of retrieving patients' cumulative test results and at the same time performing delta or percentage difference checks on such data in the detection of non-analytical errors and unexpected variations in results. The role of the computer in minimising transcription errors, reducing turn-around time of testing and reporting, as well as improving the quality of laboratory reports is also mentioned.

  17. Quality Assurance

    NASA Technical Reports Server (NTRS)

    1981-01-01

    General Electric Company requested a report from Jet Propulsion Laboratory which provides detailed information on failure modes, stress analysis and other reliability considerations was requested. General Electric Company's Nuclear Energy Division incorporated its information with that of the report. Routinely used, the report enables personnel time savings in establishing applicable screening test data.

  18. Multinational Quality Assurance

    ERIC Educational Resources Information Center

    Kinser, Kevin

    2011-01-01

    Multinational colleges and universities pose numerous challenges to the traditional models of quality assurance that are designed to validate domestic higher education. When institutions cross international borders, at least two quality assurance protocols are involved. To guard against fraud and abuse, quality assurance in the host country is…

  19. AAPM Task Group 128: Quality assurance tests for prostate brachytherapy ultrasound systems

    SciTech Connect

    Pfeiffer, Douglas; Sutlief, Steven; Feng Wenzheng; Pierce, Heather M.; Kofler, Jim

    2008-12-15

    While ultrasound guided prostate brachytherapy has gained wide acceptance as a primary treatment tool for prostate cancer, quality assurance of the ultrasound guidance system has received very little attention. Task Group 128 of the American Association of Physicists in Medicine was created to address quality assurance requirements specific to transrectal ultrasound used for guidance of prostate brachytherapy. Accurate imaging guidance and dosimetry calculation depend upon the quality and accuracy of the ultrasound image. Therefore, a robust quality assurance program for the ultrasound system is essential. A brief review of prostate brachytherapy and ultrasound physics is provided, followed by a recommendation for elements to be included in a comprehensive test phantom. Specific test recommendations are presented, covering grayscale visibility, depth of penetration, axial and lateral resolution, distance measurement, area measurement, volume measurement, needle template/electronic grid alignment, and geometric consistency with the treatment planning computer.

  20. HPV testing for primary cervical screening: Laboratory issues and evolving requirements for robust quality assurance.

    PubMed

    Carozzi, Francesca Maria; Del Mistro, Annarosa; Cuschieri, Kate; Frayle, Helena; Sani, Cristina; Burroni, Elena

    2016-03-01

    This review aims to highlight the importance of Quality Assurance for Laboratories performing HPV test for Cervical Cancer Screening. An HPV test, to be used as primary screening test, must be validated according to international criteria, based on comparison of its clinical accuracy to HC2 or GP5+/6+ PCR-EIA tests. The number of validated platforms is increasing and appropriate Quality Assurance Programs (QAPs) which can interrogate longitudinal robustness and quality are paramount. This document describes the following topics: (1) the characteristics of an HPV laboratory and the personnel training needs, to ensure an elevated quality of the entire process and the optimal use of the resources; (2) the Quality Assurance, as both internal (IQA) and external quality assessment (EQA) systems, to be implemented and performed, and the description of the existing EQAs, including limitations; (3) general considerations for an optimal EQA program for hrHPV primary screening Due to the importance of Quality Assurance for this field, international efforts are necessary to improve QA International Collaboration.

  1. Underground test area quality assurance project plan, Nevada test site, Nevada. Revision 1

    SciTech Connect

    1997-04-01

    This Quality Assurance Project Plan (QAPP) is one of the planning documents used for the Underground Test Area (UGTA) Subproject at the Nevada Test Site (NTS) which falls under the oversight of the U.S. Department of Energy, Nevada Operations Office (DOE/NV) Nevada Environmental Restoration Project (NV ERP). The Nevada ERP consists of environmental restoration activities on the NTS, Tonopah Test Range, Nellis Air Force Range, and eight sites in five other states. The UGTA Subproject constitutes a component of the Nevada Environmental Restoration Project. The purposes of the UGTA Subproject are to define boundaries around each Corrective Action Unit (CAU), as defined by the Federal Facility Agreement and Consent Order (FFACO), that establish areas containing water that may be unsafe for domestic or municipal use and to establish monitoring programs for each CAU that will verify modeling upon which the boundaries are based.

  2. Sampling Plan Development in Support of DLA’s Quality Assurance Laboratory Testing Program

    DTIC Science & Technology

    1991-09-01

    Objective 2 states "Develop and implement initiatives for continuously improving the quality of products and services delivered to our customers." Task 6 of... of products provided to the military services, Defense Logistics Agency (DLA) embarked on a comprehensive plan *° for enhancing its Quality Assurance...technically sound and appropriate for supporting the DoDIG’s Audit recommendation for laboratory testing. xi I. INTRODUCTION In its quest to improve the quality

  3. Final Test Results of Quality Assurance Classes Using the Instructional Concepts Program (ICP).

    ERIC Educational Resources Information Center

    Monteiro, Mike; Bailey, Jerry

    As part of the Quality Assurance procedures, a final test was administered to a sample of the classes participating in the 1970-71 Instructional Concepts Program (ICP). The posttest was designed to measure end-of-program performance on each of the six program outcomes: Color, Shape, Size, Position, Amount, and Pre-Mathematics. This report…

  4. Assuring the quality of results of test hardness IRHD: IPT's case study

    NASA Astrophysics Data System (ADS)

    Yojo, T.; Miranda, M. J. A. C.; Oliveira, C. B.; Matteucci, C.

    2015-10-01

    This paper presents the experience of the Laboratory Trees, Woods and Furniture - LAMM in calibrating the durometer IRHD and assuring the quality of its test results, since there are no Certified Reference Material and laboratory in the Brazilian Calibration Network that can calibrate the equipment. To solve this problem, the IRHD hardness (N method) was quantified in three ways: a) by measuring the modulus of elasticity of the material, b) by measuring the depth the sphere entered the material and c) the durometer's direct reading. With the IRHD hardness measured by accepted international standards techniques, it was possible to evaluate the accuracy of the test results that assured the calibration of the equipment.

  5. Quality assurance for in vitro alternative test methods: quality control issues in test kit production.

    PubMed

    Rispin, Amy; Harbell, John W; Klausner, Mitchell; Jordan, Foster T; Coecke, Sandra; Gupta, Kailash; Stitzel, Katherine

    2004-06-01

    In vitro toxicology methods are being adopted by regulatory agencies worldwide. Many of these methods have been validated by using proprietary materials, often in the form of test kits. Guidelines for the use of Good Laboratory Practice methods for in vitro methods have been proposed. However, users of the data from these methods also need to be reassured that the proprietary materials and the test kits will provide consistent, good quality data over time, not just during the validation process. This paper presents an overview of the methods currently used by representatives of kit manufacturers and contract testing laboratories to ensure that the results from methods that utilise test kits are reproducible over time and across different types of test materials. This information will be valuable as a basis for future discussion on the need for formalised oversight of the quality of these materials.

  6. Underground Test Area Activity Quality Assurance Plan Nevada National Security Site, Nevada. Revision 2

    SciTech Connect

    Krenzien, Susan; Farnham, Irene

    2015-06-01

    This Quality Assurance Plan (QAP) provides the overall quality assurance (QA) requirements and general quality practices to be applied to the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) Underground Test Area (UGTA) activities. The requirements in this QAP are consistent with DOE Order 414.1D, Change 1, Quality Assurance (DOE, 2013a); U.S. Environmental Protection Agency (EPA) Guidance for Quality Assurance Project Plans for Modeling (EPA, 2002); and EPA Guidance on the Development, Evaluation, and Application of Environmental Models (EPA, 2009). If a participant’s requirement document differs from this QAP, the stricter requirement will take precedence. NNSA/NFO, or designee, must review this QAP every two years. Changes that do not affect the overall scope or requirements will not require an immediate QAP revision but will be incorporated into the next revision cycle after identification. Section 1.0 describes UGTA objectives, participant responsibilities, and administrative and management quality requirements (i.e., training, records, procurement). Section 1.0 also details data management and computer software requirements. Section 2.0 establishes the requirements to ensure newly collected data are valid, existing data uses are appropriate, and environmental-modeling methods are reliable. Section 3.0 provides feedback loops through assessments and reports to management. Section 4.0 provides the framework for corrective actions. Section 5.0 provides references for this document.

  7. Underground Test Area Activity Quality Assurance Plan Nevada National Security Site, Nevada. Revision 1

    SciTech Connect

    Farnham, Irene; Krenzien, Susan

    2012-10-01

    This Quality Assurance Plan (QAP) provides the overall quality assurance (QA) requirements and general quality practices to be applied to the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Underground Test Area (UGTA) activities. The requirements in this QAP are consistent with DOE Order 414.1C, Quality Assurance (DOE, 2005); U.S. Environmental Protection Agency (EPA) Guidance for Quality Assurance Project Plans for Modeling (EPA, 2002); and EPA Guidance on the Development, Evaluation, and Application of Environmental Models (EPA, 2009). NNSA/NSO, or designee, must review this QAP every two years. Changes that do not affect the overall scope or requirements will not require an immediate QAP revision but will be incorporated into the next revision cycle after identification. Section 1.0 describes UGTA objectives, participant responsibilities, and administrative and management quality requirements (i.e., training, records, procurement). Section 1.0 also details data management and computer software requirements. Section 2.0 establishes the requirements to ensure newly collected data are valid, existing data uses are appropriate, and environmental-modeling methods are reliable. Section 3.0 provides feedback loops through assessments and reports to management. Section 4.0 provides the framework for corrective actions. Section 5.0 provides references for this document.

  8. [Determination of tumor biological parameters in breast cancer: round robin testing for quality assurance].

    PubMed

    Liessem, S; Winkens, W; Jonigk, D; Wasielewski, R V; Fisseler-Eckhoff, A; Rüschoff, J; Kreipe, H-H

    2014-02-01

    Round robin testing for quality assurance in the determination of the breast cancer biomarkers estrogen receptor (ER), progesterone receptor (PR) and epithelial growth factor receptor 2 (HER2) have been carried out in Germany for 13 years. As the first quality assurance trial worldwide tissue microarrays with 20 different breast cancer specimens were used. As a further innovation the challenges were split into a test part representing routine cases and a training part enriched with difficult borderline cases in order to uncover latent weaknesses in the participating laboratories. Certificates are issued based exclusively on the test part. Similar to NordiQC and UKNequas stained slides are assessed externally and the quality of staining and evaluation are considered separately. Since 2010 an additional internet-based trial without assessment of the staining quality is offered for ER and PR. Since the introduction of the round robin trials the numbers of participants (n = 200-250) and the success rates have steadily increased. The breast cancer quality assurance trial ranks first with regard to the number of participants in Germany. It could be demonstrated that regular participation in the round robin test leads to an improvement of staining results of ER, PR and HER2 and hence appears to be mandatory for maintaining quality standards. The use of fully automated immunohistochemical staining procedures has steadily increased and these are now used by approximately 50 % of participants.

  9. Construction quality assurance report

    SciTech Connect

    Roscha, V.

    1994-09-08

    This report provides a summary of the construction quality assurance (CQA) observation and test results, including: The results of the geosynthetic and soil materials conformance testing. The observation and testing results associates with the installation of the soil liners. The observation and testing results associated with the installation of the HDPE geomembrane liner systems. The observation and testing results associated with the installation of the leachate collection and removal systems. The observation and testing results associated with the installation of the working surfaces. The observation and testing results associated with in-plant manufacturing process. Summary of submittal reviews by Golder Construction Services, Inc. The submittal and certification of the piping material specifications. The observation and verification associated of the Acceptance Test Procedure results of the operational equipment functions. Summary of the ECNs which are incorporated into the project.

  10. Development of quality assurance and performance testing for the Process Experimental Pilot Plant

    SciTech Connect

    Dole, L.R.; McDaniel, E.W.; Robinson, S.M.

    1984-06-01

    The Process Experimental Pilot Plant (PREPP) is planned for operation by EG and G Idaho, Inc., to demonstrate a full-scale, cement-based, disposal process for transuranic (TRU) wastes. Procedures need to be developed to determine the quality of the waste product during processing and the durability of the final waste form produced in this facility. This report summarizes basic guidelines for the selection of the waste form composition and process conditions that affect product performance. Physical property tests that may be applicable for quality assurance during processing are also described. Approaches to accelerated performance tests needed to predict the performance of the cement-based waste form are identified, and suggestions are made for the development of processing tests to assure the quality of the final waste-host product. 29 references, 3 figures, 3 tables.

  11. A national quality assurance survey of Neisseria gonorrhoeae testing.

    PubMed

    Trembizki, Ella; Lahra, Monica; Stevens, Kerrie; Freeman, Kevin; Hogan, Tiffany; Hogg, Geoff; Lawrence, Andrew; Limnios, Athena; Pearson, Julie; Smith, Helen; Nissen, Michael; Sloots, Theo; Whiley, David

    2014-01-01

    The aims of this study were to (1) conduct a national survey of Neisseria gonorrhoeae identification by National Neisseria Network (NNN) reference laboratories contributing data to the Australian Gonococcal Surveillance Programme and (2) determine the prevalence in Australia of strains of N. gonorrhoeae lacking gene sequences commonly targeted by in-house PCR assays for confirmation of gonococcal nucleic acid amplification tests. Gonococcal clinical isolates referred to NNN laboratories for the first half of 2012 were screened using in-house real-time PCR assays targeting multicopy opa, porA pseudogene and cppB genes. There were 2455 clinical gonococcal isolates received in the study period; 98.6 % (2420/2455) of isolates harboured all three gene targets, 0.12 % (3/2455) were porA-negative, 0.04 % (1/2455) opa-negative and 1.14 % (28/2455) cppB-negative by PCR. Notably, no isolates were simultaneously negative for two targets. However, three isolates failed to be amplified by all three PCR methods, one isolate of which was shown to be a commensal Neisseria strain by 16S rRNA sequencing. Using PCR as the reference standard the results showed that (1) identification of N. gonorrhoeae isolates by NNN laboratories was highly specific (99.96 %) and (2) strains of N. gonorrhoeae lacking gene sequences commonly targeted by in-house PCR assays are present but not widespread throughout Australia at this point in time.

  12. 10 CFR 26.137 - Quality assurance and quality control.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 1 2012-01-01 2012-01-01 false Quality assurance and quality control. 26.137 Section 26....137 Quality assurance and quality control. (a) Quality assurance program. Each licensee testing... metabolites. (b) Performance testing and quality control requirements for validity screening tests....

  13. 10 CFR 26.137 - Quality assurance and quality control.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 1 2011-01-01 2011-01-01 false Quality assurance and quality control. 26.137 Section 26....137 Quality assurance and quality control. (a) Quality assurance program. Each licensee testing... metabolites. (b) Performance testing and quality control requirements for validity screening tests....

  14. 10 CFR 26.137 - Quality assurance and quality control.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 1 2013-01-01 2013-01-01 false Quality assurance and quality control. 26.137 Section 26....137 Quality assurance and quality control. (a) Quality assurance program. Each licensee testing... metabolites. (b) Performance testing and quality control requirements for validity screening tests....

  15. 10 CFR 26.137 - Quality assurance and quality control.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 1 2014-01-01 2014-01-01 false Quality assurance and quality control. 26.137 Section 26....137 Quality assurance and quality control. (a) Quality assurance program. Each licensee testing... metabolites. (b) Performance testing and quality control requirements for validity screening tests....

  16. 10 CFR 26.137 - Quality assurance and quality control.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Quality assurance and quality control. 26.137 Section 26....137 Quality assurance and quality control. (a) Quality assurance program. Each licensee testing... metabolites. (b) Performance testing and quality control requirements for validity screening tests....

  17. Quality assurance of metabolomics.

    PubMed

    Bouhifd, Mounir; Beger, Richard; Flynn, Thomas; Guo, Lining; Harris, Georgina; Hogberg, Helena; Kaddurah-Daouk, Rima; Kamp, Hennicke; Kleensang, Andre; Maertens, Alexandra; Odwin-DaCosta, Shelly; Pamies, David; Robertson, Donald; Smirnova, Lena; Sun, Jinchun; Zhao, Liang; Hartung, Thomas

    2015-01-01

    Metabolomics promises a holistic phenotypic characterization of biological responses to toxicants. This technology is based on advanced chemical analytical tools with reasonable throughput, including mass-spectroscopy and NMR. Quality assurance, however - from experimental design, sample preparation, metabolite identification, to bioinformatics data-mining - is urgently needed to assure both quality of metabolomics data and reproducibility of biological models. In contrast to microarray-based transcriptomics, where consensus on quality assurance and reporting standards has been fostered over the last two decades, quality assurance of metabolomics is only now emerging. Regulatory use in safety sciences, and even proper scientific use of these technologies, demand quality assurance. In an effort to promote this discussion, an expert workshop discussed the quality assurance needs of metabolomics. The goals for this workshop were 1) to consider the challenges associated with metabolomics as an emerging science, with an emphasis on its application in toxicology and 2) to identify the key issues to be addressed in order to establish and implement quality assurance procedures in metabolomics-based toxicology. Consensus has still to be achieved regarding best practices to make sure sound, useful, and relevant information is derived from these new tools.

  18. Software quality assurance handbook

    SciTech Connect

    Not Available

    1990-09-01

    There are two important reasons for Software Quality Assurance (SQA) at Allied-Signal Inc., Kansas City Division (KCD): First, the benefits from SQA make good business sense. Second, the Department of Energy has requested SQA. This handbook is one of the first steps in a plant-wide implementation of Software Quality Assurance at KCD. The handbook has two main purposes. The first is to provide information that you will need to perform software quality assurance activities. The second is to provide a common thread to unify the approach to SQA at KCD. 2 figs.

  19. A routine quality assurance test for CT automatic exposure control systems.

    PubMed

    Iball, Gareth R; Moore, Alexis C; Crawford, Elizabeth J

    2016-07-01

    The study purpose was to develop and validate a quality assurance test for CT automatic exposure control (AEC) systems based on a set of nested polymethylmethacrylate CTDI phantoms. The test phantom was created by offsetting the 16 cm head phantom within the 32 cm body annulus, thus creating a three part phantom. This was scanned at all acceptance, routine, and some nonroutine quality assurance visits over a period of 45 months, resulting in 115 separate AEC tests on scanners from four manufacturers. For each scan the longitudinal mA modulation pattern was generated and measurements of image noise were made in two annular regions of interest. The scanner displayed CTDIvol and DLP were also recorded. The impact of a range of AEC configurations on dose and image quality were assessed at acceptance testing. For systems that were tested more than once, the percentage of CTDIvol values exceeding 5%, 10%, and 15% deviation from baseline was 23.4%, 12.6%, and 8.1% respectively. Similarly, for the image noise data, deviations greater than 2%, 5%, and 10% from baseline were 26.5%, 5.9%, and 2%, respectively. The majority of CTDIvol and noise deviations greater than 15% and 5%, respectively, could be explained by incorrect phantom setup or protocol selection. Barring these results, CTDIvol deviations of greater than 15% from baseline were found in 0.9% of tests and noise deviations greater than 5% from baseline were found in 1% of tests. The phantom was shown to be sensitive to changes in AEC setup, including the use of 3D, longitudinal or rotational tube current modulation. This test methodology allows for continuing performance assessment of CT AEC systems, and we recommend that this test should become part of routine CT quality assurance programs. Tolerances of ±15% for CTDIvol and ±5% for image noise relative to baseline values should be used. PACS number(s): 87.57.Q.

  20. Development of quality assurance and performance testing for the Process Experimental Pilot Plant

    SciTech Connect

    Dole, L.R.; McDaniel, E.W.; Robinson, S.M.

    1984-08-01

    The Process Experimental Pilot Plant (PREPP) is planned for operation by EG and G Idaho, Inc., to demonstrate a full-scale, cement-based, disposal process for transuranic (TRU) wastes. Procedures need to be developed to determine the quality of the waste product during processing and the durability of the final waste form produced in this facility. This report summarizes basic guidelines for the selection of the waste form composition and process conditions that affect product performance. Physical property tests that may be applicable for quality assurance during processing are also described. Approaches to accelerated performance tests needed to predict the performance of the cement-based waste form are identified, and suggestions are made for the development of processing tests to ensure the quality of the final waste-host product. 29 references, 3 figures, 4 tables.

  1. Recommended procedures for performance testing of radiobioassay laboratories: Volume 1, Quality assurance. [Contains Glossary

    SciTech Connect

    Fenrick, H.W.; MacLellan, J.A.

    1988-11-01

    Draft American National Standards Institute (ANSI) Standard N13.30 (Performance Criteria for Radiobioassay) was developed in response to a concern expressed by the US Department of Energy and US Nuclear Regulatory Commission to help ensure that bioassay laboratories provide accurate and consistent results. The draft standard specifies the criteria for defining the procedures necessary to establish a bioassay performance-testing laboratory and program. The testing laboratory will conduct tests to evaluate the performance of service laboratories. Pacific Northwest Laboratory helped define responsibilities and develop procedures as part of an effort to evaluate the draft ANSI N13.30 performance criteria for quality assurance at bioassay laboratories. This report recommends elements of quality assurance and quality control responsibilities for the bioassay performance-testing laboratory program, including the qualification and performance of personnel and the calibration, certification, and performance of equipment. The data base and recommended records system for documenting radiobioassay performance at the service laboratories are also presented. 15 refs.

  2. Quality assurance practices in Europe: a survey of molecular genetic testing laboratories.

    PubMed

    Berwouts, Sarah; Fanning, Katrina; Morris, Michael A; Barton, David E; Dequeker, Elisabeth

    2012-11-01

    In the 2000s, a number of initiatives were taken internationally to improve quality in genetic testing services. To contribute to and update the limited literature available related to this topic, we surveyed 910 human molecular genetic testing laboratories, of which 291 (32%) from 29 European countries responded. The majority of laboratories were in the public sector (81%), affiliated with a university hospital (60%). Only a minority of laboratories was accredited (23%), and 26% was certified. A total of 22% of laboratories did not participate in external quality assessment (EQA) and 28% did not use reference materials (RMs). The main motivations given for accreditation were to improve laboratory profile (85%) and national recognition (84%). Nearly all respondents (95%) would prefer working in an accredited laboratory. In accredited laboratories, participation in EQA (P<0.0001), use of RMs (P=0.0014) and availability of continuous education (CE) on medical/scientific subjects (P=0.023), specific tasks (P=0.0018), and quality assurance (P<0.0001) were significantly higher than in non-accredited laboratories. Non-accredited laboratories expect higher restriction of development of new techniques (P=0.023) and improvement of work satisfaction (P=0.0002) than accredited laboratories. By using a quality implementation score (QIS), we showed that accredited laboratories (average score 92) comply better than certified laboratories (average score 69, P<0.001), and certified laboratories better than other laboratories (average score 44, P<0.001), with regard to the implementation of quality indicators. We conclude that quality practices vary widely in European genetic testing laboratories. This leads to a potentially dangerous situation in which the quality of genetic testing is not consistently assured.

  3. Quality Assurance for All

    ERIC Educational Resources Information Center

    Cheung, Peter P. T.; Tsui, Cecilia B. S.

    2010-01-01

    For higher education reform, most decision-makers aspire to achieving a higher participation rate and a respectable degree of excellence with diversity at the same time. But very few know exactly how. External quality assurance is a fair basis for differentiation but there can be doubt and resistance in some quarters. Stakeholder interests differ…

  4. Software Quality Assurance Metrics

    NASA Technical Reports Server (NTRS)

    McRae, Kalindra A.

    2004-01-01

    Software Quality Assurance (SQA) is a planned and systematic set of activities that ensures conformance of software life cycle processes and products conform to requirements, standards and procedures. In software development, software quality means meeting requirements and a degree of excellence and refinement of a project or product. Software Quality is a set of attributes of a software product by which its quality is described and evaluated. The set of attributes includes functionality, reliability, usability, efficiency, maintainability, and portability. Software Metrics help us understand the technical process that is used to develop a product. The process is measured to improve it and the product is measured to increase quality throughout the life cycle of software. Software Metrics are measurements of the quality of software. Software is measured to indicate the quality of the product, to assess the productivity of the people who produce the product, to assess the benefits derived from new software engineering methods and tools, to form a baseline for estimation, and to help justify requests for new tools or additional training. Any part of the software development can be measured. If Software Metrics are implemented in software development, it can save time, money, and allow the organization to identify the caused of defects which have the greatest effect on software development. The summer of 2004, I worked with Cynthia Calhoun and Frank Robinson in the Software Assurance/Risk Management department. My task was to research and collect, compile, and analyze SQA Metrics that have been used in other projects that are not currently being used by the SA team and report them to the Software Assurance team to see if any metrics can be implemented in their software assurance life cycle process.

  5. Development of a quality-assurance program for the Tritium Systems Test Assembly

    SciTech Connect

    Minor, R.C.

    1981-01-01

    A quality assurance program was developed for TSTA with the attempt in mind to satisfy the developmental nature of the project. Numerous reviews replace strict guidelines because guidelines are one of the objectives of the project, not a basis for it. The reviews assure adequate technical consideration and avoid unilateral decisions. Other major requirements of the program plan include interfacing with another quality assurance organization, the assignment of responsibilities, and instructions for the preparation of SDD's. Areas of concern are, in general, budget related, and include receiving inspection and acceptance of items. A software program is only now being established.

  6. [Medical quality assurance today].

    PubMed

    Schäfer, Robert D

    2008-01-01

    Both the quality and performance of health systems are strongly influenced by the number and the qualification of the professional staff. Quality assurance programs help to analyse causalities which are responsible for medical malpractice. On the basis of the experiences gained by the performance of established Quality Assurance Programs (QAP) in the North Rhine area since 1982 various aspects of the efficiency of these programs will be discussed. The implementation of legal regulations making these programs mandatory is criticised not only for its bureaucratic effect but also for the attempt to exclude professional experts from the interpretation of results. It is recommended to liberalize these regulations in order to facilitate improvement of methods and participation of the medical profession.

  7. Quality Assurance and Quality Control, Part 1.

    PubMed

    Akers, Michael J

    2015-01-01

    The tragedy surrounding the New England Compounding Center and contaminated steroid syringe preparations clearly points out what can happen if quality-assurance and quality-control procedures are not strictly practiced in the compounding of sterile preparations. This article represents part 1 of a 2-part article on quality-assurance and quality-control procedures and serves as an introduction to the topic of finished preparation release checks and tests. Part 1 highlights what is required to comply with United States Pharmacopeia General Chapter <797>, and part 2 continues with a discussion on the requirements of <797> as well as what is required in chapter < 1163> with respect to quality assurance of compounded sterile preparations. Written procedures, good documentation practices, and specific details for clarity, sterility, and bacterial endotoxin (pyrogen) testing are presented in this article.

  8. Testing and listing disinfectants – instrument and product of quality assurance

    PubMed Central

    Gebel, Jürgen

    2007-01-01

    In Germany, the Disinfectants Commission of the Association for Applied Hygiene (VAH) ensures that the user can avail of procedures that meet the stipulated quality requirements. These requirements are based on the tried and tested standard methods of the German Society of Hygiene and Microbiology (DGHM) as well as on European standards. They take account of the different requirements dictated by the various fields of application, reflecting the quality assurance system in a transparent manner. Special emphasis is increasingly placed on retesting the products already available on the market. In multi-center trials the inter- and intralaboratory fluctuations in the test results are ascertained, the quest for suitable standard substances intensified, culture conditions and detection procedures are standardized and the test procedures and potential influence factors analyzed in detail. The aim here is to devise test procedures that will yield a reproducible and reliable result independently of the test location, and meet the requirements of everyday practice. Attention must be paid to, inter alia, the prevailing microbial spectrum in quality and quantity, the prevailing organic and inorganic load as well as material and surface properties. The test procedures are gradually brought into line with the current stock of scientific knowledge, because such a task calls for conscientiousness, tenacity and patience as well as continuous dialog between research, industry and practice. Thanks to these joint efforts, we are increasingly better able to meet the demands made by intelligent and selective prophylactic disinfection. PMID:20200678

  9. Quality Assurance for University Teaching.

    ERIC Educational Resources Information Center

    Ellis, Roger, Ed.

    This book, written from a British perspective, presents 17 papers on quality assurance in teaching at the university level. The first eight papers address issues of assuring quality and include: (1) "Quality Assurance for University Teaching; Issues and Approaches" (Roger Ellis); (2) "A British Standard for University…

  10. Quality Assurance in Nursing Homes.

    ERIC Educational Resources Information Center

    Balgopal, Pallassana R.; And Others

    This manual, developed for the nursing home employee, examines the concept of quality assurance in nursing homes, describes the benefits of an effective quality assurance program, and provides guidelines to aid nursing homes in developing an appropriate quality assurance program. After a brief introduction, a working definition of quality…

  11. VMAT linear accelerator commissioning and quality assurance: dose control and gantry speed tests.

    PubMed

    Barnes, Michael P; Rowshanfarzad, Pejman; Greer, Peter B

    2016-05-01

    In VMAT treatment delivery the ability of the linear accelerator (linac) to accurately control dose versus gantry angle is critical to delivering the plan correctly. A new VMAT test delivery was developed to specifically test the dose versus gantry angle with the full range of allowed gantry speeds and dose rates. The gantry-mounted IBA MatriXX with attached inclinometer was used in movie mode to measure the instantaneous relative dose versus gantry angle during the plan every 0.54 s. The results were compared to the expected relative dose at each gantry angle calculated from the plan. The same dataset was also used to compare the instantaneous gantry speeds throughout the delivery compared to the expected gantry speeds from the plan. Measurements performed across four linacs generally show agreement between measurement and plan to within 1.5% in the constant dose rate regions and dose rate modulation within 0.1 s of the plan. Instantaneous gantry speed was measured to be within 0.11∘/s of the plan (1 SD). An error in one linac was detected in that the nominal gantry speed was incorrectly calibrated. This test provides a practical method to quality-assure critical aspects of VMAT delivery including dose versus gantry angle and gantry speed control. The method can be performed with any detector that can acquire time-resolved dosimetric information that can be synchronized with a measurement of gantry angle. The test fulfils several of the aims of the recent Netherlands Commission on Radiation Dosimetry (NCS) Report 24, which provides recommendations for comprehensive VMAT quality assurance. PACS number(s): 87.55.Qr.

  12. VMAT linear accelerator commissioning and quality assurance: dose control and gantry speed tests.

    PubMed

    Barnes, Michael P; Rowshanfarzad, Pejman; Greer, Peter B

    2016-05-08

    In VMAT treatment delivery the ability of the linear accelerator (linac) to accurately control dose versus gantry angle is critical to delivering the plan correctly. A new VMAT test delivery was developed to specifically test the dose versus gantry angle with the full range of allowed gantry speeds and dose rates. The gantry-mounted IBA MatriXX with attached inclinometer was used in movie mode to measure the instantaneous relative dose versus gantry angle during the plan every 0.54 s. The results were compared to the expected relative dose at each gantry angle calculated from the plan. The same dataset was also used to compare the instantaneous gan-try speeds throughout the delivery compared to the expected gantry speeds from the plan. Measurements performed across four linacs generally show agreement between measurement and plan to within 1.5% in the constant dose rate regions and dose rate modulation within 0.1 s of the plan. Instantaneous gantry speed was measured to be within 0.11°/s of the plan (1 SD). An error in one linac was detected in that the nominal gantry speed was incorrectly calibrated. This test provides a practical method to quality-assure critical aspects of VMAT delivery including dose versus gantry angle and gantry speed control. The method can be performed with any detector that can acquire time-resolved dosimetric information that can be synchronized with a measurement of gantry angle. The test fulfils several of the aims of the recent Netherlands Commission on Radiation Dosimetry (NCS) Report 24, which provides recommendations for comprehensive VMAT quality assurance.

  13. Technical Report: TG-142 compliant and comprehensive quality assurance tests for respiratory gating

    SciTech Connect

    Woods, Kyle; Rong, Yi

    2015-11-15

    Purpose: To develop and establish a comprehensive gating commissioning and quality assurance procedure in compliance with TG-142. Methods: Eight Varian TrueBeam Linacs were used for this study. Gating commissioning included an end-to-end test and baseline establishment. The end-to-end test was performed using a CIRS dynamic thoracic phantom with a moving cylinder inside the lung, which was used for carrying both optically simulated luminescence detectors (OSLDs) and Gafchromic EBT2 films while the target is moving, for a point dose check and 2D profile check. In addition, baselines were established for beam-on temporal delay and calibration of the surrogate, for both megavoltage (MV) and kilovoltage (kV) beams. A motion simulation device (MotionSim) was used to provide periodic motion on a platform, in synchronizing with a surrogate motion. The overall accuracy and uncertainties were analyzed and compared. Results: The OSLD readings were within 5% compared to the planned dose (within measurement uncertainty) for both phase and amplitude gated deliveries. Film results showed less than 3% agreement to the predicted dose with a standard sinusoid motion. The gate-on temporal accuracy was averaged at 139 ± 10 ms for MV beams and 92 ± 11 ms for kV beams. The temporal delay of the surrogate motion depends on the motion speed and was averaged at 54.6 ± 3.1 ms for slow, 24.9 ± 2.9 ms for intermediate, and 23.0 ± 20.1 ms for fast speed. Conclusions: A comprehensive gating commissioning procedure was introduced for verifying the output accuracy and establishing the temporal accuracy baselines with respiratory gating. The baselines are needed for routine quality assurance tests, as suggested by TG-142.

  14. Testing the Effectiveness of a Quality Assurance System: The Example of Hong Kong

    ERIC Educational Resources Information Center

    Lim, David

    2009-01-01

    Operating a quality assurance system in tertiary education is the rule rather than the exception, because of the belief that it will improve quality. However, proving this is not easy. This study examines three ways of providing the evidence: the a "priori" method, the stepwise backtracking method, and the external evaluation method. The…

  15. The Impact of Truth Surrogate Variance on Quality Assessment/Assurance in Wind Tunnel Testing

    NASA Technical Reports Server (NTRS)

    DeLoach, Richard

    2016-01-01

    Minimum data volume requirements for wind tunnel testing are reviewed and shown to depend on error tolerance, response model complexity, random error variance in the measurement environment, and maximum acceptable levels of inference error risk. Distinctions are made between such related concepts as quality assurance and quality assessment in response surface modeling, as well as between precision and accuracy. Earlier research on the scaling of wind tunnel tests is extended to account for variance in the truth surrogates used at confirmation sites in the design space to validate proposed response models. A model adequacy metric is presented that represents the fraction of the design space within which model predictions can be expected to satisfy prescribed quality specifications. The impact of inference error on the assessment of response model residuals is reviewed. The number of sites where reasonably well-fitted response models actually predict inadequately is shown to be considerably less than the number of sites where residuals are out of tolerance. The significance of such inference error effects on common response model assessment strategies is examined.

  16. The quality assurance liaison: Combined technical and quality assurance support

    NASA Astrophysics Data System (ADS)

    Bolivar, S. L.; Day, J. L.

    1993-03-01

    The role of the quality assurance liaison, the responsibilities of this position, and the evolutionary changes in duties over the last six years are described. The role of the quality assurance liaison has had a very positive impact on the Los Alamos Yucca Mountain Site Characterization (YW) quality assurance program. Having both technical and quality assurance expertise, the quality assurance liaisons are able to facilitate communications with scientists on quality assurance issues and requirements, thereby generating greater productivity in scientific investigations. The quality assurance liaisons help ensure that the scientific community knows and implements existing requirements, is aware of new or changing regulations, and is able to conduct scientific work within Project requirements. The influence of the role of the quality assurance liaison can be measured by an overall improvement in attitude of the staff regarding quality assurance requirements and improved job performance, as well as a decrease in deficiencies identified during both internal and external audits and surveillances. This has resulted in a more effective implementation of quality assurance requirements.

  17. 30 CFR 7.7 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality assurance. 7.7 Section 7.7 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY General § 7.7 Quality assurance. Applicants...

  18. 30 CFR 7.7 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality assurance. 7.7 Section 7.7 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY General § 7.7 Quality assurance. Applicants...

  19. 30 CFR 7.7 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality assurance. 7.7 Section 7.7 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY General § 7.7 Quality assurance. Applicants...

  20. 30 CFR 7.7 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quality assurance. 7.7 Section 7.7 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY General § 7.7 Quality assurance. Applicants...

  1. 30 CFR 7.7 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quality assurance. 7.7 Section 7.7 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY General § 7.7 Quality assurance. Applicants...

  2. Sophisticated test objects for the quality assurance of optical computed tomography scanners

    NASA Astrophysics Data System (ADS)

    Rahman, A. T. Abdul; Bräuer-Krisch, Elke; Brochard, Thierry; Adamovics, John; Clowes, S. K.; Bradley, David; Doran, Simon J.

    2011-07-01

    Optical computed tomography (CT), in conjunction with radiochromic gels and plastics, shows great potential for radiation therapy dose verification in 3D. However, an effective quality assurance (QA) regime for the various scanners currently available still remains to be developed. We show how the favourable properties of the PRESAGE® radiochromic polymer may be exploited to create highly sophisticated QA phantoms. Five 60 mm diameter cylindrical PRESAGE® samples were irradiated using the x-ray microbeam radiation therapy facility on the ID-17 biomedical beamline at the European Synchrotron Radiation Facility. Samples were then imaged on the University of Surrey parallel-beam optical CT scanner. The sample irradiations were designed to allow a variety of tests to be performed, including assessments of linearity, modulation transfer function (three independent measurements), geometric distortion and the effect of treatment fractionation. It is clear that, although the synchrotron method produces extremely high-quality test objects, it is not practical on a routine basis, because of its reliance on a highly specialized radiation source. Hence, we investigated a second possibility: three PRESAGE® samples were illuminated with ultraviolet light of wavelength 365 nm, using cheap masks created by laser-printing patterns onto overhead projector acetate sheets. There was good correlation between optical densities measured by the CT scanner and the expected UV 'dose' delivered. The results are encouraging and a proposal is made for a scanner test regime based on calibrated and well-characterized PRESAGE® samples.

  3. Development of a multi-VOC reference material for quality assurance in materials emission testing.

    PubMed

    Nohr, Michael; Horn, Wolfgang; Jann, Oliver; Richter, Matthias; Lorenz, Wilhelm

    2015-04-01

    Emission test chamber measurement is necessary to proof building materials as sources of volatile organic compounds (VOCs). The results of such measurements are used to evaluate materials and label them according to their potential to emit harmful substances, polluting indoor air. If only labelled materials were installed indoors, this would improve indoor air quality and prevent negative impacts on human health. Because of the complex testing procedure, reference materials for the quality assurance are mandatory. Currently, there is a lack of such materials because most building products show a broad variation of emissions even within one batch. A previous study indicates lacquers, mixed with volatile organic pollutants, as reproducible emission source for a wide range of substances. In the present study, the curing of the lacquer-VOC mixture inside micro-chambers was optimised. Therefore, the humidity and the chamber flow were varied. Typical indoor air pollutants with a wide range of volatilities, for example, styrene, n-hexadecane, dimethyl and dibutyl phthalate were selected. It turned out that, under optimised curing parameters inside the micro-chamber, their emission can be reproduced with variations of less than 10 %. With this, a next important step towards a reference material for emission testing was achieved.

  4. Characterization of currently marketed heparin products: key tests for LMWH quality assurance.

    PubMed

    Ye, Hongping; Toby, Timothy K; Sommers, Cynthia D; Ghasriani, Houman; Trehy, Michael L; Ye, Wei; Kolinski, Richard E; Buhse, Lucinda F; Al-Hakim, Ali; Keire, David A

    2013-11-01

    During the 2007-2008 heparin crisis it was found that the United States Pharmacopeia (USP) testing monograph for heparin sodium or low molecular weight heparins did not detect the presence of the contaminant, oversulfated chondroitin sulfate (OSCS). In response to this concern, new tests and specifications were developed by the Food and Drug Administration (FDA) and USP and put in place to detect not only the contaminant OSCS, but also to improve assurance of quality and purity of these drug products. The USP monographs for the low molecular weight heparins (LMWHs) approved for use in the United States (dalteparin, tinzaparin and enoxaparin) are also undergoing revision to include many of the same tests used for heparin sodium, including; one-dimensional (1D) 500 MHz (1)H NMR, SAX-HPLC, percent galactosamine in total hexosamine and anticoagulation time assays with purified Factor IIa or Factor Xa. These tests represent orthogonal approaches for heparin identification, measurement of bioactivity and for detection of process impurities or contaminants in these drug products. Here we describe results from a survey of multiple lots from three types of LMWHs in the US market which were collected after the 2009 heparin sodium monograph revision. In addition, innovator and generic versions of formulated enoxaparin products purchased in 2011 are compared using these tests and found to be highly similar within the discriminating power of the assays applied.

  5. ASVCP guidelines: quality assurance for point-of-care testing in veterinary medicine.

    PubMed

    Flatland, Bente; Freeman, Kathleen P; Vap, Linda M; Harr, Kendal E

    2013-12-01

    Point-of-care testing (POCT) refers to any laboratory testing performed outside the conventional reference laboratory and implies close proximity to patients. Instrumental POCT systems consist of small, handheld or benchtop analyzers. These have potential utility in many veterinary settings, including private clinics, academic veterinary medical centers, the community (eg, remote area veterinary medical teams), and for research applications in academia, government, and industry. Concern about the quality of veterinary in-clinic testing has been expressed in published veterinary literature; however, little guidance focusing on POCT is available. Recognizing this void, the ASVCP formed a subcommittee in 2009 charged with developing quality assurance (QA) guidelines for veterinary POCT. Guidelines were developed through literature review and a consensus process. Major recommendations include (1) taking a formalized approach to POCT within the facility, (2) use of written policies, standard operating procedures, forms, and logs, (3) operator training, including periodic assessment of skills, (4) assessment of instrument analytical performance and use of both statistical quality control and external quality assessment programs, (5) use of properly established or validated reference intervals, (6) and ensuring accurate patient results reporting. Where possible, given instrument analytical performance, use of a validated 13s control rule for interpretation of control data is recommended. These guidelines are aimed at veterinarians and veterinary technicians seeking to improve management of POCT in their clinical or research setting, and address QA of small chemistry and hematology instruments. These guidelines are not intended to be all-inclusive; rather, they provide a minimum standard for maintenance of POCT instruments in the veterinary setting.

  6. Quality assurance of intracellular cytokine staining assays: analysis of multiple rounds of proficiency testing.

    PubMed

    Jaimes, Maria C; Maecker, Holden T; Yan, Ming; Maino, Vernon C; Hanley, Mary Beth; Greer, Angela; Darden, Janice M; D'Souza, M Patricia

    2011-01-05

    When evaluating candidate prophylactic HIV and cancer vaccines, intracellular cytokine staining (ICS) assays that measure the frequency and magnitude of antigen-specific T-cell subsets are one tool to monitor immunogen performance and make product advancement decisions. To assess the inter-laboratory assay variation among multiple laboratories testing vaccine candidates, the NIH/NIAID/DAIDS in collaboration with BD Biosciences implemented an ICS Quality Assurance Program (QAP). Seven rounds of testing have been conducted in which 16 laboratories worldwide participated. In each round, IFN-γ, IL-2 and/or TNF-α responses in CD4+ and CD8+ T-cells to CEF or CMV pp65 peptide mixes were tested using cryopreserved peripheral blood mononuclear cells (PBMC) from CMV seropositive donors. We found that for responses measured above 0.2%, inter-laboratory %CVs were, on average, 35%. No differences in inter-laboratory variation were observed if a 4-color antibody cocktail or a 7-color combination was used. Moreover, the data allowed identification of important sources of variability for flow cytometry-based assays, including: number of collected events, gating strategy and instrument setup and performance. As a consequence, in this multi-site study we were able to define pass and fail criteria for ICS assays, which will be adopted in the subsequent rounds of testing and could be easily extrapolated to QAP for other flow cytometry-based assays.

  7. 7 CFR 90.102 - Quality assurance review.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Quality assurance review. 90.102 Section 90.102... INTRODUCTION Quality Assurance § 90.102 Quality assurance review. (a) Each laboratory performing tests and analysis under this subchapter will be subject to a quality assurance program evaluation at least...

  8. 7 CFR 90.102 - Quality assurance review.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Quality assurance review. 90.102 Section 90.102... INTRODUCTION Quality Assurance § 90.102 Quality assurance review. (a) Each laboratory performing tests and analysis under this subchapter will be subject to a quality assurance program evaluation at least...

  9. Implementation of test for quality assurance in nuclear medicine gamma camera

    NASA Astrophysics Data System (ADS)

    Moreno, A. Montoya; Laguna, A. Rodríguez; Zamudio, Flavio E. Trujillo

    2012-10-01

    In nuclear medicine (NM) over 90% of procedures are performed for diagnostic purposes. To ensure adequate diagnostic quality of images and the optimization of the doses received by patients originated from the radioactive material is essential for regular monitoring and equipment performance through a quality assurance program (QAP). The QAP consists of 15 proposed performance tomographic and not tomographic gamma camera (GC) tests, and is based on recommendations of international organizations. We describe some results of the performance parameters of QAP applied to a GC model e.cam Siemens, of the Department of NM of the National Cancer Institute of Mexico (INCan). The results were: (1) The average intrinsic spatial resolution (Rin) was 4.67 ± 0.25 mm at the limit of acceptance criterion of 4.4 mm. (2) The sensitivity extrinsic (Sext), with maximum variations of 1.8% (less than 2% which is the criterion of acceptance). (3) Rotational Uniformity (Urot), with values of integral uniformity (IU) in the useful field of view detector (UFOV), with maximum percentage change of 0.97% and monthly variations equal angles, ranging from 0.13 to 0.99% less than 1%. (4) The displacement of the center of rotation (DCOR), indicated a maximum deviation of 0.155 ± 0.039 mm less than 4.795 mm, an absolute deviation of less than 0.5 where pixel 0.085 pixel is suggested, the criteria are assigned to low-energy collimator high resolution. (5) In tomographic uniformity (Utomo), UI values (%) and percentage noise level (rms%) were 7.54 ± 1.53 and 4.18 ± 1.69 which are consistent with the limits of acceptance of 7.0-12.0% and 3.0-6.0% respectively. The smallest cold sphere has a diameter of 11.4 mm. The implementation of a QAP allows for high quality diagnostic images, optimization of the doses given to patients, a reduction of exposure to occupationally exposed workers (POE, by its Spanish acronym), and generally improves the productivity of the service. This proposal can be used to

  10. Implementation of test for quality assurance in nuclear medicine gamma camera

    SciTech Connect

    Montoya Moreno, A.; Rodriguez Laguna, A.; Trujillo Zamudio, Flavio E

    2012-10-23

    In nuclear medicine (NM) over 90% of procedures are performed for diagnostic purposes. To ensure adequate diagnostic quality of images and the optimization of the doses received by patients originated from the radioactive material is essential for regular monitoring and equipment performance through a quality assurance program (QAP). The QAP consists of 15 proposed performance tomographic and not tomographic gamma camera (GC) tests, and is based on recommendations of international organizations. We describe some results of the performance parameters of QAP applied to a GC model e.cam Siemens, of the Department of NM of the National Cancer Institute of Mexico (INCan). The results were: (1) The average intrinsic spatial resolution (R{sub in}) was 4.67 {+-} 0.25 mm at the limit of acceptance criterion of 4.4 mm. (2) The sensitivity extrinsic (S{sub ext}), with maximum variations of 1.8% (less than 2% which is the criterion of acceptance). (3) Rotational Uniformity (U{sub rot}), with values of integral uniformity (IU) in the useful field of view detector (UFOV), with maximum percentage change of 0.97% and monthly variations equal angles, ranging from 0.13 to 0.99% less than 1%. (4) The displacement of the center of rotation (DCOR), indicated a maximum deviation of 0.155 {+-} 0.039 mm less than 4.795 mm, an absolute deviation of less than 0.5 where pixel 0.085 pixel is suggested, the criteria are assigned to low-energy collimator high resolution. (5) In tomographic uniformity (U{sub tomo}), UI values (%) and percentage noise level (rms%) were 7.54 {+-} 1.53 and 4.18 {+-} 1.69 which are consistent with the limits of acceptance of 7.0-12.0% and 3.0-6.0% respectively. The smallest cold sphere has a diameter of 11.4 mm. The implementation of a QAP allows for high quality diagnostic images, optimization of the doses given to patients, a reduction of exposure to occupationally exposed workers (POE, by its Spanish acronym), and generally improves the productivity of the

  11. 30 CFR 15.8 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quality assurance. 15.8 Section 15.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... § 15.8 Quality assurance. (a) Applicants granted an approval or an extension of approval under...

  12. 30 CFR 14.8 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quality assurance. 14.8 Section 14.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... Quality assurance. Applicants granted an approval or an extension of approval under this Part must: (a)...

  13. 30 CFR 15.8 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quality assurance. 15.8 Section 15.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... § 15.8 Quality assurance. (a) Applicants granted an approval or an extension of approval under...

  14. 30 CFR 15.8 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality assurance. 15.8 Section 15.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... § 15.8 Quality assurance. (a) Applicants granted an approval or an extension of approval under...

  15. 30 CFR 15.8 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality assurance. 15.8 Section 15.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... § 15.8 Quality assurance. (a) Applicants granted an approval or an extension of approval under...

  16. 30 CFR 15.8 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality assurance. 15.8 Section 15.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... § 15.8 Quality assurance. (a) Applicants granted an approval or an extension of approval under...

  17. 30 CFR 14.8 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quality assurance. 14.8 Section 14.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... Quality assurance. Applicants granted an approval or an extension of approval under this Part must: (a)...

  18. 30 CFR 14.8 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality assurance. 14.8 Section 14.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... Quality assurance. Applicants granted an approval or an extension of approval under this Part must: (a)...

  19. 30 CFR 14.8 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality assurance. 14.8 Section 14.8 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... Quality assurance. Applicants granted an approval or an extension of approval under this Part must: (a)...

  20. External quality assurance of malaria nucleic acid testing for clinical trials and eradication surveillance.

    PubMed

    Murphy, Sean C; Hermsen, Cornelus C; Douglas, Alexander D; Edwards, Nick J; Petersen, Ines; Fahle, Gary A; Adams, Matthew; Berry, Andrea A; Billman, Zachary P; Gilbert, Sarah C; Laurens, Matthew B; Leroy, Odile; Lyke, Kristen E; Plowe, Christopher V; Seilie, Annette M; Strauss, Kathleen A; Teelen, Karina; Hill, Adrian V S; Sauerwein, Robert W

    2014-01-01

    Nucleic acid testing (NAT) for malaria parasites is an increasingly recommended diagnostic endpoint in clinical trials of vaccine and drug candidates and is also important in surveillance of malaria control and elimination efforts. A variety of reported NAT assays have been described, yet no formal external quality assurance (EQA) program provides validation for the assays in use. Here, we report results of an EQA exercise for malaria NAT assays. Among five centers conducting controlled human malaria infection trials, all centers achieved 100% specificity and demonstrated limits of detection consistent with each laboratory's pre-stated expectations. Quantitative bias of reported results compared to expected results was generally <0.5 log10 parasites/mL except for one laboratory where the EQA effort identified likely reasons for a general quantitative shift. The within-laboratory variation for all assays was low at <10% coefficient of variation across a range of parasite densities. Based on this study, we propose to create a Molecular Malaria Quality Assessment program that fulfills the need for EQA of malaria NAT assays worldwide.

  1. Quality Assurance Testing of Version 1.3 of U.S. EPA Benchmark Dose Software (Presentation)

    EPA Science Inventory

    EPA benchmark dose software (BMDS) issued to evaluate chemical dose-response data in support of Agency risk assessments, and must therefore be dependable. Quality assurance testing methods developed for BMDS were designed to assess model dependability with respect to curve-fitt...

  2. Resource Conservation and Recovery Act Industrial Sites quality assurance project plan: Nevada Test Site, Nevada

    SciTech Connect

    Not Available

    1994-06-01

    This quality assurance project plan (QAPjP) describes the measures that shall be taken to ensure that the environmental data collected during characterization and closure activities of Resource Conservation and Recovery Act (RCRA) Industrial Sites at the Nevada Test Site (NTS) are meaningful, valid, defensible, and can be used to achieve project objectives. These activities are conducted by the US Department of Energy Nevada Operations Office (DOE/NV) under the Nevada Environmental Restoration (ER) Project. The Nevada ER Project consists of environmental restoration activities on the NTS, Tonopah Test Range, Nellis Air Force Range, and eight sites in five other states. The RCRA Industrial Sites subproject constitutes a component of the Nevada ER Project. Currently, this QAPjP is limited to the seven RCRA Industrial Sites identified within this document that are to be closed under an interim status and pertains to all field-investigation, analytical-laboratory, and data-review activities in support of these closures. The information presented here supplements the RCRA Industrial Sites Project Management Plan and is to be used in conjunction with the site-specific subproject sampling and analysis plans.

  3. Quality Assurance [for Persons with Developmental Disabilities].

    ERIC Educational Resources Information Center

    Lakin, Charlie, Ed.; And Others

    1993-01-01

    This newsletter feature issue focuses on quality assurance and innovative efforts to enhance service quality for persons with developmental disabilities. Individual articles include: "Redesigning Quality Assurance" (Clarence J. Sundram); "Quality Assurance, Quality Enhancement" (Charlie Lakin et al.); "Challenging…

  4. 40 CFR 792.35 - Quality assurance unit.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Quality assurance unit. 792.35 Section... assurance unit. (a) A testing facility shall have a quality assurance unit which shall be responsible for... quality assurance unit shall be entirely separate from and independent of the personnel engaged in...

  5. The quality assurance role in the Deep Space Network

    NASA Technical Reports Server (NTRS)

    Sirpilla, R. L.

    1981-01-01

    The quality assurance section provides skilled personnel who perform the following functions: quality hardware engineering, quality software engineering, inspection and testing, and an independent assessment to quality, engineering and project requirements. The quality assurance section provides specifications, workmanship standards, process specifications and quality assurance procedures in support of DSN equipment. In addition, the quality assurance section reviews DSN engineering documents to ensure that appropriate and adequate quality provisions are included.

  6. Advanced Fuel Quality Assurance Standards Based on Thermal Testing and Chemometric Modeling

    DTIC Science & Technology

    2015-10-05

    Briefing Charts 3. DATES COVERED (From - To) 15 September 2015 - 05 October 2015 4. TITLE AND SUBTITLE Advanced Fuel Quality Assurance Standards Based...ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NO. Air Force Research Laboratory (AFMC) AFRL/RQRC 10 E. Saturn Blvd. Edwards AFB...CA 93524-7680 9. SPONSORING / MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSOR/MONITOR’S ACRONYM(S) Air Force Research Laboratory

  7. Recent Trends in Quality Assurance

    ERIC Educational Resources Information Center

    Amaral, Alberto; Rosa, Maria Joao

    2010-01-01

    In this paper we present a brief description of the evolution of quality assurance in Europe, paying particular attention to its relationship to the rising loss of trust in higher education institutions. We finalise by analysing the role of the European Commission in the setting up of new quality assurance mechanisms that tend to promote…

  8. Development of a dynamic quality assurance testing protocol for multisite clinical trial DCE-CT accreditation

    SciTech Connect

    Driscoll, B.; Keller, H.; Jaffray, D.; Coolens, C.

    2013-08-15

    Purpose: Credentialing can have an impact on whether or not a clinical trial produces useful quality data that is comparable between various institutions and scanners. With the recent increase of dynamic contrast enhanced-computed tomography (DCE-CT) usage as a companion biomarker in clinical trials, effective quality assurance, and control methods are required to ensure there is minimal deviation in the results between different scanners and protocols at various institutions. This paper attempts to address this problem by utilizing a dynamic flow imaging phantom to develop and evaluate a DCE-CT quality assurance (QA) protocol.Methods: A previously designed flow phantom, capable of producing predictable and reproducible time concentration curves from contrast injection was fully validated and then utilized to design a DCE-CT QA protocol. The QA protocol involved a set of quantitative metrics including injected and total mass error, as well as goodness of fit comparison to the known truth concentration curves. An additional region of interest (ROI) sensitivity analysis was also developed to provide additional details on intrascanner variability and determine appropriate ROI sizes for quantitative analysis. Both the QA protocol and ROI sensitivity analysis were utilized to test variations in DCE-CT results using different imaging parameters (tube voltage and current) as well as alternate reconstruction methods and imaging techniques. The developed QA protocol and ROI sensitivity analysis was then applied at three institutions that were part of clinical trial involving DCE-CT and results were compared.Results: The inherent specificity of robustness of the phantom was determined through calculation of the total intraday variability and determined to be less than 2.2 ± 1.1% (total calculated output contrast mass error) with a goodness of fit (R{sup 2}) of greater than 0.99 ± 0.0035 (n= 10). The DCE-CT QA protocol was capable of detecting significant deviations from

  9. 7 CFR 90.102 - Quality assurance review.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) COMMODITY LABORATORY TESTING PROGRAMS INTRODUCTION Quality Assurance § 90.102 Quality assurance review. (a) Each laboratory performing tests...

  10. SAPHIRE 8 Software Quality Assurance Oversight

    SciTech Connect

    Kurt G. Vedros

    2011-09-01

    The software quality assurance oversight consists of updating and maintaining revision control of the SAPHIRE 8 quality assurance program documentation and of monitoring revision control of the SAPHIRE 8 source code. This report summarizes the oversight efforts through description of the revision control system (RCS) setup, operation and contents. Documents maintained under revision control include the Acceptance Test Plan (ATP), Configuration Management Plan, Quality Assurance Plan, Software Project Plan, Requirements Traceability Matrix (RTM), System Test Plan, SDP Interface Training Manual, and the SAPHIRE 8, 'New Features and Capabilities Overview'.

  11. Summary of Documentation for DYNA3D-ParaDyn's Software Quality Assurance Regression Test Problems

    SciTech Connect

    Zywicz, Edward

    2016-08-18

    The Software Quality Assurance (SQA) regression test suite for DYNA3D (Zywicz and Lin, 2015) and ParaDyn (DeGroot, et al., 2015) currently contains approximately 600 problems divided into 21 suites, and is a required component of ParaDyn’s SQA plan (Ferencz and Oliver, 2013). The regression suite allows developers to ensure that software modifications do not unintentionally alter the code response. The entire regression suite is run prior to permanently incorporating any software modification or addition. When code modifications alter test problem results, the specific cause must be determined and fully understood before the software changes and revised test answers can be incorporated. The regression suite is executed on LLNL platforms using a Python script and an associated data file. The user specifies the DYNA3D or ParaDyn executable, number of processors to use, test problems to run, and other options to the script. The data file details how each problem and its answer extraction scripts are executed. For each problem in the regression suite there exists an input deck, an eight-processor partition file, an answer file, and various extraction scripts. These scripts assemble a temporary answer file in a specific format from the simulation results. The temporary and stored answer files are compared to a specific level of numerical precision, and when differences are detected the test problem is flagged as failed. Presently, numerical results are stored and compared to 16 digits. At this accuracy level different processor types, compilers, number of partitions, etc. impact the results to various degrees. Thus, for consistency purposes the regression suite is run with ParaDyn using 8 processors on machines with a specific processor type (currently the Intel Xeon E5530 processor). For non-parallel regression problems, i.e., the two XFEM problems, DYNA3D is used instead. When environments or platforms change, executables using the current source code and the new

  12. Software Quality Assurance Audits Guidebooks

    NASA Technical Reports Server (NTRS)

    1990-01-01

    The growth in cost and importance of software to NASA has caused NASA to address the improvement of software development across the agency. One of the products of this program is a series of guidebooks that define a NASA concept of the assurance processes that are used in software development. The Software Assurance Guidebook, NASA-GB-A201, issued in September, 1989, provides an overall picture of the NASA concepts and practices in software assurance. Second level guidebooks focus on specific activities that fall within the software assurance discipline, and provide more detailed information for the manager and/or practitioner. This is the second level Software Quality Assurance Audits Guidebook that describes software quality assurance audits in a way that is compatible with practices at NASA Centers.

  13. Modernization of software quality assurance

    NASA Technical Reports Server (NTRS)

    Bhaumik, Gokul

    1988-01-01

    The customers satisfaction depends not only on functional performance, it also depends on the quality characteristics of the software products. An examination of this quality aspect of software products will provide a clear, well defined framework for quality assurance functions, which improve the life-cycle activities of software development. Software developers must be aware of the following aspects which have been expressed by many quality experts: quality cannot be added on; the level of quality built into a program is a function of the quality attributes employed during the development process; and finally, quality must be managed. These concepts have guided our development of the following definition for a Software Quality Assurance function: Software Quality Assurance is a formal, planned approach of actions designed to evaluate the degree of an identifiable set of quality attributes present in all software systems and their products. This paper is an explanation of how this definition was developed and how it is used.

  14. Testing the portal imager GLAaS algorithm for machine quality assurance

    PubMed Central

    Nicolini, G; Vanetti, E; Clivio, A; Fogliata, A; Boka, G; Cozzi, L

    2008-01-01

    Background To report about enhancements introduced in the GLAaS calibration method to convert raw portal imaging images into absolute dose matrices and to report about application of GLAaS to routine radiation tests for linac quality assurance procedures programmes. Methods Two characteristic effects limiting the general applicability of portal imaging based dosimetry are the over-flattening of images (eliminating the "horns" and "holes" in the beam profiles induced by the presence of flattening filters) and the excess of backscattered radiation originated by the detector robotic arm supports. These two effects were corrected for in the new version of GLAaS formalism and results are presented to prove the improvements for different beams, detectors and support arms. GLAaS was also tested for independence from dose rate (fundamental to measure dynamic wedges). With the new corrections, it is possible to use GLAaS to perform standard tasks of linac quality assurance. Data were acquired to analyse open and wedged fields (mechanical and dynamic) in terms of output factors, MU/Gy, wedge factors, profile penumbrae, symmetry and homogeneity. In addition also 2D Gamma Evaluation was applied to measurement to expand the standard QA methods. GLAaS based data were compared against calculations on the treatment planning system (the Varian Eclipse) and against ion chamber measurements as consolidated benchmark. Measurements were performed mostly on 6 MV beams from Varian linacs. Detectors were the PV-as500/IAS2 and the PV-as1000/IAS3 equipped with either the robotic R- or Exact- arms. Results Corrections for flattening filter and arm backscattering were successfully tested. Percentage difference between PV-GLAaS measurements and Eclipse calculations relative doses at the 80% of the field size, for square and rectangular fields larger than 5 × 5 cm2 showed a maximum range variation of -1.4%, + 1.7% with a mean variation of <0.5%. For output factors, average percentage

  15. Automated damage test facilities for materials development and production optic quality assurance at Lawrence Livermore National Laboratory

    SciTech Connect

    Battersby, C; Dickson, R; Jennings, R; Kimmons, J; Kozlowski, M R; Maricle, S; Mouser, R; Runkel, M; Schwartz, S; Sheehan, L M; Weinzapfel, C

    1998-12-22

    The Laser Program at LLNL has developed automated facilities for damage testing optics up to 1 meter in diameter. The systems were developed to characterize the statistical distribution of localized damage performance across large-aperture National Ignition Facility optics. Full aperture testing is a key component of the quality assurance program for several of the optical components. The primary damage testing methods used are R:1 mapping and raster scanning. Automation of these test methods was required to meet the optics manufacturing schedule. The automated activities include control and diagnosis of the damage-test laser beam as well as detection and characterization of damage events.

  16. Integral test phantom for dosimetric quality assurance of image guided and intensity modulated stereotactic radiotherapy

    SciTech Connect

    Letourneau, Daniel; Keller, Harald; Sharpe, Michael B.; Jaffray, David A.

    2007-05-15

    The objective of this work is to develop a dosimetric phantom quality assurance (QA) of linear accelerators capable of cone-beam CT (CBCT) image guided and intensity-modulated radiotherapy (IG-IMRT). This phantom is to be used in an integral test to quantify in real-time both the performance of the image guidance and the dose delivery systems in terms of dose localization. The prototype IG-IMRT QA phantom consisted of a cylindrical imaging phantom (CatPhan) combined with an array of 11 radiation diodes mounted on a 10 cm diameter disk, oriented perpendicular to the phantom axis. Basic diode response characterization was performed for 6 and 18 MV photons. The diode response was compared to planning system calculations in the open and penumbrae regions of simple and complex beam arrangements. The clinical use of the QA phantom was illustrated in an integral test of an IG-IMRT treatment designed for a clinical spinal radiosurgery case. The sensitivity of the phantom to multileaf collimator (MLC) calibration and setup errors in the clinical setting was assessed by introducing errors in the IMRT plan or by displacing the phantom. The diodes offered good response linearity and long-term reproducibility for both 6 and 18 MV. Axial dosimetry of coplanar beams (in a plane containing the beam axes) was made possible with the nearly isoplanatic response of the diodes over 360 deg. of gantry (usually within {+-}1%). For single beam geometry, errors in phantom placement as small as 0.5 mm could be accurately detected (in gradient {>=}1%/mm). In clinical setting, MLC systematic errors of 1 mm on a single MLC bank introduced in the IMRT plan were easily detectable with the QA phantom. The QA phantom demonstrated also sufficient sensitivity for the detection of setup errors as small as 1 mm for the IMRT delivery. These results demonstrated that the prototype can accurately and efficiently verify the entire IG-IMRT process. This tool, in conjunction with image guidance capabilities

  17. Real-time quality assurance testing using photonic techniques: Application to iodine water system

    NASA Technical Reports Server (NTRS)

    Arendale, W. F.; Hatcher, Richard; Garlington, Yadilett; Harwell, Jack; Everett, Tracey

    1990-01-01

    A feasibility study of the use of inspection systems incorporating photonic sensors and multivariate analyses to provide an instrumentation system that in real-time assures quality and that the system in control has been conducted. A system is in control when the near future of the product quality is predictable. Off-line chemical analyses can be used for a chemical process when slow kinetics allows time to take a sample to the laboratory and the system provides a recovery mechanism that returns the system to statistical control without intervention of the operator. The objective for this study has been the implementation of do-it-right-the-first-time and just-in-time philosophies. The Environment Control and Life Support Systems (ECLSS) water reclamation system that adds iodine for biocidal control is an ideal candidate for the study and implementation of do-it-right-the-first-time technologies.

  18. Real-time quality assurance testing using photonic techniques: Application to iodine water system

    NASA Astrophysics Data System (ADS)

    Arendale, W. F.; Hatcher, Richard; Garlington, Yadilett; Harwell, Jack; Everett, Tracey

    1990-07-01

    A feasibility study of the use of inspection systems incorporating photonic sensors and multivariate analyses to provide an instrumentation system that in real-time assures quality and that the system in control has been conducted. A system is in control when the near future of the product quality is predictable. Off-line chemical analyses can be used for a chemical process when slow kinetics allows time to take a sample to the laboratory and the system provides a recovery mechanism that returns the system to statistical control without intervention of the operator. The objective for this study has been the implementation of do-it-right-the-first-time and just-in-time philosophies. The Environment Control and Life Support Systems (ECLSS) water reclamation system that adds iodine for biocidal control is an ideal candidate for the study and implementation of do-it-right-the-first-time technologies.

  19. BUILDING "BRIDGES" WITH QUALITY ASSURANCE

    EPA Science Inventory

    The papr describes how, rather than building "bridges" across centuries, quality assurance (QA) personnel have the opportunity to build bridges across technical disciplines, between public and private organizations, and between different QA groups. As reviewers and auditors of a...

  20. Redefining and expanding quality assurance.

    PubMed

    Robins, J L

    1992-12-01

    To meet the current standards of excellence necessary for blood establishments, we have learned from industry that a movement toward organization-wide quality assurance/total quality management must be made. Everyone in the organization must accept responsibility for participating in providing the highest quality products and services. Quality must be built into processes and design systems to support these quality processes. Quality assurance has been redefined to include a quality planning function described as the most effective way of designing quality into processes. A formalized quality planning process must be part of quality assurance. Continuous quality improvement has been identified as the strategy every blood establishment must support while striving for error-free processing as the long-term objective. The auditing process has been realigned to support and facilitate this same objective. Implementing organization-wide quality assurance/total quality management is one proven plan for guaranteeing the quality of the 20 million products that are transfused into 4 million patients each year and for moving toward the new order.

  1. Underground Test Area Fiscal Year 2013 Annual Quality Assurance Report Nevada National Security Site, Nevada, Revision 0

    SciTech Connect

    Krenzien, Susan; Marutzky, Sam

    2014-01-01

    This report is required by the Underground Test Area (UGTA) Quality Assurance Plan (QAP) and identifies the UGTA quality assurance (QA) activities for fiscal year (FY) 2013. All UGTA organizations—U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO); Desert Research Institute (DRI); Lawrence Livermore National Laboratory (LLNL); Los Alamos National Laboratory (LANL); Navarro-Intera, LLC (N-I); National Security Technologies, LLC (NSTec); and the U.S. Geological Survey (USGS)—conducted QA activities in FY 2013. The activities included conducting assessments, identifying findings and completing corrective actions, evaluating laboratory performance, and publishing documents. In addition, integrated UGTA required reading and corrective action tracking was instituted.

  2. Underground Test Area Fiscal Year 2012 Annual Quality Assurance Report Nevada National Security Site, Nevada, Revision 0

    SciTech Connect

    Farnham, Irene; Marutzky, Sam

    2013-01-01

    This report is mandated by the Underground Test Area (UGTA) Quality Assurance Project Plan (QAPP) and identifies the UGTA quality assurance (QA) activities for fiscal year (FY) 2012. All UGTA organizations—U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO); Desert Research Institute (DRI); Lawrence Livermore National Laboratory (LLNL); Los Alamos National Laboratory (LANL); Navarro-Intera, LLC (N-I); National Security Technologies, LLC (NSTec); and the U.S. Geological Survey (USGS)—conducted QA activities in FY 2012. The activities included conducting assessments, identifying findings and completing corrective actions, evaluating laboratory performance, revising the QAPP, and publishing documents. In addition, processes and procedures were developed to address deficiencies identified in the FY 2011 QAPP gap analysis.

  3. 40 CFR 51.363 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 2 2013-07-01 2013-07-01 false Quality assurance. 51.363 Section 51... Requirements § 51.363 Quality assurance. An ongoing quality assurance program shall be implemented to discover... impede program performance. The quality assurance and quality control procedures shall be...

  4. 40 CFR 51.363 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 2 2011-07-01 2011-07-01 false Quality assurance. 51.363 Section 51... Requirements § 51.363 Quality assurance. An ongoing quality assurance program shall be implemented to discover... impede program performance. The quality assurance and quality control procedures shall be...

  5. Transuranic Waste Characterization Quality Assurance Program Plan

    SciTech Connect

    1995-04-30

    This quality assurance plan identifies the data necessary, and techniques designed to attain the required quality, to meet the specific data quality objectives associated with the DOE Waste Isolation Pilot Plant (WIPP). This report specifies sampling, waste testing, and analytical methods for transuranic wastes.

  6. National External Quality Assurance Program Pakistan (NEQAPP) –A Milestone in Proficiency Testing in Pakistan

    PubMed Central

    Ijaz, Aamir

    2016-01-01

    Objective The objective of this study was to highlight current status and importance of National External Quality Assurance Program Pakistan (NEQAPP). Study Design: Cross sectional study Place and duration of study Department of Chemical Pathology and Endocrinology, Armed Forces Institute of Pathology (AFIP) from August to October 2015. Methods The study data was extracted from electronic NEQAPP database. Results from 2014-2015 were evaluated for clinical chemistry, hematology, microbiology, and immunoassay programs. Frequencies of unsatisfactory results of individual analytes as well as of all the participating laboratories were calculated. Results Failure rate of newly enrolled laboratories were more as compared to those which were participating for the last two years. The percentages of unsatisfactory results of all laboratories were 19% and 15% in 2014 and 2015, respectively. Fifteen analytes were selected according to their increasing percentage of participation. Failure rate was highest for alkaline phosphatase (35%) followed by creatinine (22%) and urea (20%) in two years analysis. Performance of laboratories in each quarter was evaluated depending upon number of analytes in which they fail to pass. The major failures were due to clerical and technical errors as determined during data compilation of results. Conclusion There is an increase in trend of participating in NEQAPP by health care laboratories which is a step towards laboratory quality management system in Pakistan. Nonetheless, there is a need for improving quality of laboratory results. PMID:28149266

  7. 48 CFR 12.208 - Contract quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Contract quality assurance... Items 12.208 Contract quality assurance. Contracts for commercial items shall rely on contractors' existing quality assurance systems as a substitute for Government inspection and testing before tender...

  8. 40 CFR 160.35 - Quality assurance unit.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Quality assurance unit. 160.35 Section... LABORATORY PRACTICE STANDARDS Organization and Personnel § 160.35 Quality assurance unit. (a) A testing facility shall have a quality assurance unit which shall be responsible for monitoring each study to...

  9. 40 CFR 792.35 - Quality assurance unit.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 33 2013-07-01 2013-07-01 false Quality assurance unit. 792.35 Section... ACT (CONTINUED) GOOD LABORATORY PRACTICE STANDARDS Organization and Personnel § 792.35 Quality assurance unit. (a) A testing facility shall have a quality assurance unit which shall be responsible...

  10. 40 CFR 75.45 - Daily quality assurance criteria.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Daily quality assurance criteria. 75... (CONTINUED) CONTINUOUS EMISSION MONITORING Alternative Monitoring Systems § 75.45 Daily quality assurance... that such tests are unnecessary for providing quality-assured data....

  11. 48 CFR 12.208 - Contract quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Contract quality assurance... Items 12.208 Contract quality assurance. Contracts for commercial items shall rely on contractors' existing quality assurance systems as a substitute for Government inspection and testing before tender...

  12. 40 CFR 75.45 - Daily quality assurance criteria.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Daily quality assurance criteria. 75... (CONTINUED) CONTINUOUS EMISSION MONITORING Alternative Monitoring Systems § 75.45 Daily quality assurance... that such tests are unnecessary for providing quality-assured data....

  13. 40 CFR 160.35 - Quality assurance unit.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Quality assurance unit. 160.35 Section... LABORATORY PRACTICE STANDARDS Organization and Personnel § 160.35 Quality assurance unit. (a) A testing facility shall have a quality assurance unit which shall be responsible for monitoring each study to...

  14. 40 CFR 160.35 - Quality assurance unit.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Quality assurance unit. 160.35 Section... LABORATORY PRACTICE STANDARDS Organization and Personnel § 160.35 Quality assurance unit. (a) A testing facility shall have a quality assurance unit which shall be responsible for monitoring each study to...

  15. 10 CFR 71.37 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Quality assurance. 71.37 Section 71.37 Energy NUCLEAR... Package Approval § 71.37 Quality assurance. (a) The applicant shall describe the quality assurance program... quality assurance program that are applicable to the particular package design under...

  16. 10 CFR 71.37 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Quality assurance. 71.37 Section 71.37 Energy NUCLEAR... Package Approval § 71.37 Quality assurance. (a) The applicant shall describe the quality assurance program... quality assurance program that are applicable to the particular package design under...

  17. 10 CFR 71.37 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Quality assurance. 71.37 Section 71.37 Energy NUCLEAR... Package Approval § 71.37 Quality assurance. (a) The applicant shall describe the quality assurance program... quality assurance program that are applicable to the particular package design under...

  18. 10 CFR 71.37 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Quality assurance. 71.37 Section 71.37 Energy NUCLEAR... Package Approval § 71.37 Quality assurance. (a) The applicant shall describe the quality assurance program... quality assurance program that are applicable to the particular package design under...

  19. 10 CFR 71.37 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Quality assurance. 71.37 Section 71.37 Energy NUCLEAR... Package Approval § 71.37 Quality assurance. (a) The applicant shall describe the quality assurance program... quality assurance program that are applicable to the particular package design under...

  20. Thoughts on Internal and External Quality Assurance

    ERIC Educational Resources Information Center

    Zhang, Jianxin

    2012-01-01

    Quality assurance of higher education is made up of two parts: internal quality assurance (IQA) and external quality assurance (EQA). Both belong to a union of the coexistence and balance of yin and yang. But in reality there exists a paradox of "confusion of quality assurance (QA) subject consciousness, singularity of social QA and lack of QA…

  1. Quality Assurance 1992-2012

    ERIC Educational Resources Information Center

    Brown, Roger

    2012-01-01

    As the author's contribution to a series marking the Golden Jubilee of the Association of University Administrators, he reflects on changes in quality assurance over the past twenty years and speculates on what the future may hold for quality as the association moves into a new and very different competitive regime. He begins by discussing the…

  2. Quality Assurance Made Easy.

    ERIC Educational Resources Information Center

    Villemaire, Lorry

    Designed to help adult learners realize the importance and necessity of implementing continuous quality improvement (CQI) in a rapidly changing, competitive, and modern world of work, this document presents a comprehensive explanation of CQI. The following topics are discussed in the book's introduction and seven chapters: importance of quality in…

  3. Quality Assurance Project Plan for the Gas Generation Testing Program at the INEL

    SciTech Connect

    1994-10-01

    The data quality objectives (DQOs) for the Program are to evaluate compliance with the limits on total gas generation rates, establish the concentrations of hydrogen and methane in the total gas flow, determine the headspace concentration of VOCs in each drum prior to the start of the test, and obtain estimates of the concentrations of several compounds for mass balance purposes. Criteria for the selection of waste containers at the INEL and the parameters that must be characterized prior to and during the tests are described. Collection of gaseous samples from 55-gallon drums of contact-handled transuranic waste for the gas generation testing is discussed. Analytical methods and calibrations are summarized. Administrative quality control measures described in this QAPjP include the generation, review, and approval of project documentation; control and retention of records; measures to ensure that personnel, subcontractors or vendors, and equipment meet the specifications necessary to achieve the required data quality for the project.

  4. Quality assurance for environmental analytical chemistry: 1980

    SciTech Connect

    Gladney, E.S.; Goode, W.E.; Perrin, D.R.; Burns, C.E.

    1981-09-01

    The continuing quality assurance effort by the Environmental Surveillance Group is presented. Included are all standard materials now in use, their consensus or certified concentrations, quality control charts, and all quality assurance measurements made by H-8 during 1980.

  5. Process chemistry {ampersand} statistics quality assurance plan

    SciTech Connect

    Meznarich, H.K.

    1996-08-01

    This document provides quality assurance guidelines and quality control requirements for Process Chemistry and Statistics. This document is designed on the basis of Hanford Analytical Services Quality Assurance Plan (HASQAP) technical guidelines and is used for governing process chemistry activities.

  6. Quality Assurance Program. QAP Workbook.

    ERIC Educational Resources Information Center

    Pelavin Research Inst., Washington, DC.

    The Quality Assurance Program (QAP) workbook is intended to assist institutions of higher education conduct qualitative and quantitative evaluations of their financial aid operations in relation to requirements of Title IV of the Higher Education Act. The workbook provides a structured approach for incorporating a cyclical Title IV QA system into…

  7. Quality assurance and analysis of water levels in wells on Pahute Mesa and vicinity, Nevada Test Site, Nye County, Nevada

    USGS Publications Warehouse

    Fenelon, Joseph M.

    2000-01-01

    Periodic and continual water-level data from 1963 to 1998 were compiled and quality assured for 65 observation wells on Pahute Mesa and vicinity, Nye County, Nevada. As part of the quality assurance of all water levels, ancillary data pertinent to computing hydraulic heads in wells were compiled and analyzed. Quality-assured water levels that were not necessarily in error but which did not represent static heads in the regional aquifer system, or required some other qualification, were flagged. Water levels flagged include those recovering from recent pumping or well construction, water levels affected by nuclear tests, and measurements affected by borehole deviations. A cursory examination of about 30 wells with available water-level and down-hole temperature data indicate that water levels in most wells on Pahute Mesa would not be significantly affected by temperature if corrected to 95 degrees Fahrenheit. Wells with large corrections (greater than 10 feet) are those with long water columns (greater than 1,500 feet of water above the assumed point of inflow) in combination with mean water-column temperatures exceeding 105 degrees Fahrenheit. Water-level fluctuations in wells on Pahute Mesa are caused by several factors including infiltration of precipitation, barometric pressure, Earth tides, ground-water pumpage, and seismic events caused by tectonic activity and underground nuclear testing. No observed water-level fluctuations were attributed to a naturally occurring earthquake. The magnitude and duration of changes in water levels caused by nuclear tests are affected by the test size and the distance from a well to the test. Identifying water levels that might be affected by past nuclear tests is difficult because pre-testing water-level data are sparse. Hydrologically significant trends were found in 13 of 25 wells with multiple years of water-level record. The largest change in water levels (1,029 feet in 25 years) occurred in well U-19v PS 1D as a result of

  8. Waste Management Quality Assurance Plan

    SciTech Connect

    Not Available

    1993-11-30

    Lawrence Berkeley Laboratory`s Environment Department addresses its responsibilities through activities in a variety of areas. The need for a comprehensive management control system for these activities has been identified by the Department of Energy (DOE). The WM QA (Waste Management Quality Assurance) Plan is an integral part of a management system that provides controls necessary to ensure that the department`s activities are planned, performed, documented, and verified. This WM QA Plan defines the requirements of the WM QA program. These requirements are derived from DOE Order 5700.6C, Quality Assurance, the LBL Operating and Assurance Program Plan (OAP, LBL PUB-3111), and other environmental compliance documents applicable to WM activities. The requirements presented herein, as well as the procedures and methodologies that direct the implementation of these requirements, will undergo review and revisions as necessary. The provisions of this QA Plan and its implementing documents apply to quality-affecting activities performed by and for WM. It is also applicable to WM contractors, vendors, and other LBL organizations associated with WM activities, except where such contractors, vendors, or organizations are governed by their own WM-approved QA programs. References used in the preparation of this document are (1) ASME NQA-1-1989, (2) ANSI/ASQC E4 (Draft), (3) Waste Management Quality Assurance Implementing Management Plan (LBL PUB-5352, Rev. 1), (4) LBL Operating and Assurance Program Plan (OAP), LBL PUB-3111, 2/3/93. A list of terms and definitions used throughout this document is included as Appendix A.

  9. A rapid HPLC procedure for analysis of analgesic pharmaceutical mixtures for quality assurance and drug diversion testing.

    PubMed

    Wolf, Carl E; Poklis, Alphonse

    2005-10-01

    A simple high-performance liquid chromatographic (HPLC) method that allows for the rapid identification and quantification of analgesic and anesthetic solutions typically used in surgical procedures or patient controlled analgesia is presented. The separation of bupivacaine, clonidine, fentanyl, hydromorphone, midazolam, and morphine is complete in less than 20 min. The method allows test solutions to be either directly injected or diluted prior to injection into the HPLC system. The method is useful from the standpoint that pharmaceutical preparations are usually submitted with the known drug of interest and expected concentration. The method is also useful for initial screening of solutions submitted that are either unknown or of questionable identity. The method has been successfully applied as part of hospital-based quality control and quality assurance programs to detect not only errors in the preparation of solutions of scheduled drugs, but also to uncover illegal diversion of drugs of abuse by medical personnel.

  10. Cardiac catheterization laboratory imaging quality assurance program.

    PubMed

    Wondrow, M A; Laskey, W K; Hildner, F J; Cusma, J; Holmes, D R

    2001-01-01

    With the recent approval of the National Electrical Manufacturers Association (NEMA) standard for "Characteristics of and Test Procedures for a Phantom to Benchmark Cardiac Fluoroscopic and Photographic Performance," comprehensive cardiac image assurance control programs are now possible. This standard was developed by a joint NEMA/Society for Cardiac Angiography and Interventions (SCA&I) working group of imaging manufacturers and cardiology society professionals over the past 4 years. This article details a cardiac catheterization laboratory image quality assurance and control program that includes the new standard along with current regulatory requirements for cardiac imaging. Because of the recent proliferation of digital imaging equipment, quality assurance for cardiac imaging fluoroscopy and digital imaging are critical. Included are the previous works recommended by the American College of Cardiology (ACC) and American Heart Association (AHA), Society for Cardiac Angiographers and Interventions (SCA&I), and authors of previous image quality subjects.

  11. 23 CFR 637.207 - Quality assurance program.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... ensure that the design-builder is providing the quality of materials and construction required by the... CONSTRUCTION INSPECTION AND APPROVAL Quality Assurance Procedures for Construction § 637.207 Quality assurance...) Quality control sampling and testing results may be used as part of the acceptance decision provided...

  12. 23 CFR 637.207 - Quality assurance program.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ensure that the design-builder is providing the quality of materials and construction required by the... CONSTRUCTION INSPECTION AND APPROVAL Quality Assurance Procedures for Construction § 637.207 Quality assurance...) Quality control sampling and testing results may be used as part of the acceptance decision provided...

  13. Quality assurance in forensic pathology.

    PubMed

    Ong, Beng Beng; Milne, Nathan

    2009-06-01

    One of the requirements for proper running of a pathology laboratory is implementation of a quality assurance programme. Forensic pathology is not exempted, especially so when cases are increasing in complexity. It is not difficult to introduce a quality assurance programme even in a small forensic centre. Among the steps that can be implemented including introduction of a set of minimal standards in performance of the autopsy, timeliness and report writing, a vigorous peer review process either internally or externally and participation in external quality programmes. Proper documentation of the post-mortem process (photography, slides and blocks and various imaging modalities) is to be encouraged. There should be limits set on workload of pathologists as overburden is known to lower standards. A pleasant work environment is also essential. Personal continuous medical education should be made mandatory. Introduction of a quality assurance programme will not only improve standards but minimise possible negligence. The post-mortem reports will be seen to carry more weight in court.

  14. 40 CFR 30.54 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Quality assurance. 30.54 Section 30.54... NON-PROFIT ORGANIZATIONS Post-Award Requirements Reports and Records § 30.54 Quality assurance. If the... data generation, the grantee shall develop and implement quality assurance practices consisting...

  15. 40 CFR 194.22 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Quality assurance. 194.22 Section 194... General Requirements § 194.22 Quality assurance. (a)(1) As soon as practicable after April 9, 1996, the Department shall adhere to a quality assurance program that implements the requirements of ASME...

  16. 40 CFR 194.22 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 25 2011-07-01 2011-07-01 false Quality assurance. 194.22 Section 194... General Requirements § 194.22 Quality assurance. (a)(1) As soon as practicable after April 9, 1996, the Department shall adhere to a quality assurance program that implements the requirements of ASME...

  17. 40 CFR 31.45 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Quality assurance. 31.45 Section 31.45... Requirements Reports, Records, Retention, and Enforcement § 31.45 Quality assurance. If the grantee's project... quality assurance practices consisting of policies, procedures, specifications, standards,...

  18. 40 CFR 31.45 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Quality assurance. 31.45 Section 31.45... Requirements Reports, Records, Retention, and Enforcement § 31.45 Quality assurance. If the grantee's project... quality assurance practices consisting of policies, procedures, specifications, standards,...

  19. 40 CFR 30.54 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Quality assurance. 30.54 Section 30.54... NON-PROFIT ORGANIZATIONS Post-Award Requirements Reports and Records § 30.54 Quality assurance. If the... data generation, the grantee shall develop and implement quality assurance practices consisting...

  20. 40 CFR 31.45 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Quality assurance. 31.45 Section 31.45... Requirements Reports, Records, Retention, and Enforcement § 31.45 Quality assurance. If the grantee's project... quality assurance practices consisting of policies, procedures, specifications, standards,...

  1. 40 CFR 194.22 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 26 2012-07-01 2011-07-01 true Quality assurance. 194.22 Section 194... General Requirements § 194.22 Quality assurance. (a)(1) As soon as practicable after April 9, 1996, the Department shall adhere to a quality assurance program that implements the requirements of ASME...

  2. 40 CFR 30.54 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Quality assurance. 30.54 Section 30.54... NON-PROFIT ORGANIZATIONS Post-Award Requirements Reports and Records § 30.54 Quality assurance. If the... data generation, the grantee shall develop and implement quality assurance practices consisting...

  3. 40 CFR 30.54 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Quality assurance. 30.54 Section 30.54... NON-PROFIT ORGANIZATIONS Post-Award Requirements Reports and Records § 30.54 Quality assurance. If the... data generation, the grantee shall develop and implement quality assurance practices consisting...

  4. 40 CFR 194.22 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 25 2014-07-01 2014-07-01 false Quality assurance. 194.22 Section 194... General Requirements § 194.22 Quality assurance. (a)(1) As soon as practicable after April 9, 1996, the Department shall adhere to a quality assurance program that implements the requirements of ASME...

  5. 40 CFR 30.54 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Quality assurance. 30.54 Section 30.54... NON-PROFIT ORGANIZATIONS Post-Award Requirements Reports and Records § 30.54 Quality assurance. If the... data generation, the grantee shall develop and implement quality assurance practices consisting...

  6. 40 CFR 194.22 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 26 2013-07-01 2013-07-01 false Quality assurance. 194.22 Section 194... General Requirements § 194.22 Quality assurance. (a)(1) As soon as practicable after April 9, 1996, the Department shall adhere to a quality assurance program that implements the requirements of ASME...

  7. 10 CFR 76.93 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Quality assurance. 76.93 Section 76.93 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.93 Quality assurance. The Corporation shall establish, maintain, and execute a quality assurance program satisfying each...

  8. 10 CFR 76.93 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Quality assurance. 76.93 Section 76.93 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.93 Quality assurance. The Corporation shall establish, maintain, and execute a quality assurance program satisfying each...

  9. 10 CFR 76.93 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Quality assurance. 76.93 Section 76.93 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.93 Quality assurance. The Corporation shall establish, maintain, and execute a quality assurance program satisfying each...

  10. 10 CFR 76.93 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Quality assurance. 76.93 Section 76.93 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.93 Quality assurance. The Corporation shall establish, maintain, and execute a quality assurance program satisfying each...

  11. 10 CFR 76.93 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Quality assurance. 76.93 Section 76.93 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.93 Quality assurance. The Corporation shall establish, maintain, and execute a quality assurance program satisfying each...

  12. Beef Quality Assurance in Feedlots.

    PubMed

    Smith, Robert A; Thomson, Daniel U; Lee, Tiffany L

    2015-07-01

    This article discusses the Beef Quality Assurance (BQA) program, which was created by beef producers and veterinarians. The program has evolved from antibiotic residue avoidance to include animal handling, cattle comfort, food safety, and much more. It provides guidance to producers and veterinarians on best management practices and allows the beef industry to be transparent about the practices used. Veterinarians are key to helping producers implement BQA in their beef operations.

  13. Frequent major errors in antimicrobial susceptibility testing of bacterial strains distributed under the Deutsches Krebsforschungszentrum Quality Assurance Program.

    PubMed

    Boot, R

    2012-07-01

    The Quality Assurance Program (QAP) of the Deutsches Krebsforschungszentrum (DKFZ) was a proficiency testing system developed to service the laboratory animal discipline. The QAP comprised the distribution of bacterial strains from various species of animals for identification to species level and antibiotic susceptibility testing (AST). Identification capabilities were below acceptable standards. This study evaluated AST results using the DKFZ compilations of test results for all bacterial strains showing the number of participants reporting the strain as resistant (R), sensitive (S) or intermediate susceptible (I) to each antibiotic substance used. Due to lack of information about methods used, it was assumed that what the majority of the participants reported (R or S) was the correct test result and that an opposite result was a major error (ME). MEs occurred in 1375 of 14,258 (9.7%) of test results and ME% ranged from 0% to 23.2% per bacterial group-agent group combination. Considerable variation in MEs was found within groups of bacteria and within groups of agents. In addition to poor performance in proper species classification, the quality of AST in laboratory animal diagnostic laboratories seems far below standards considered acceptable in human diagnostic microbiology.

  14. Compliance with Aerospace Quality Assurance Standard AS9100

    NASA Technical Reports Server (NTRS)

    Hughitt, Brian

    2009-01-01

    The contents include: 1) United States Federal Acquisition Regulations (FAR) Part 46, Quality Assurance; 2) NASA Quality Roadmap; 3) AS9003 Inspection and Test Quality Management System; 4) Government Oversight Responsibilities; and 5) Third Party vs Second Party Oversight.

  15. ASVCP quality assurance guidelines: external quality assessment and comparative testing for reference and in-clinic laboratories.

    PubMed

    Camus, Melinda S; Flatland, Bente; Freeman, Kathleen P; Cruz Cardona, Janice A

    2015-12-01

    The purpose of this document is to educate providers of veterinary laboratory diagnostic testing in any setting about comparative testing. These guidelines will define, explain, and illustrate the importance of a multi-faceted laboratory quality management program which includes comparative testing. The guidelines will provide suggestions for implementation of such testing, including which samples should be tested, frequency of testing, and recommendations for result interpretation. Examples and a list of vendors and manufacturers supplying control materials and services to veterinary laboratories are also included.

  16. Underground Test Area Fiscal Year 2014 Annual Quality Assurance Report Nevada National Security Site, Nevada, Revision 0

    SciTech Connect

    Krenzien, Susan

    2015-01-01

    This report is required by the Underground Test Area (UGTA) Quality Assurance Plan (QAP) and identifies the UGTA quality assurance (QA) activities from October 1, 2013, through September 30, 2014 (fiscal year [FY] 2014). All UGTA organizations—U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO); Desert Research Institute (DRI); Lawrence Livermore National Laboratory (LLNL); Los Alamos National Laboratory (LANL); National Security Technologies, LLC (NSTec); Navarro-Intera, LLC (N-I); and the U.S. Geological Survey (USGS)—conducted QA activities in FY 2014. The activities included conducting oversight assessments for QAP compliance, identifying findings and completing corrective actions, evaluating laboratory performance, and publishing documents. UGTA Activity participants conducted 25 assessments on topics including safe operations, QAP compliance, activity planning, and sampling. These assessments are summarized in Section 2.0. Corrective actions tracked in FY 2014 are presented in Appendix A. Laboratory performance was evaluated based on three approaches: (1) established performance evaluation programs (PEPs), (2) interlaboratory comparisons, or (3) data review. The results of the laboratory performance evaluations, and interlaboratory comparison results are summarized in Section 4.0. The UGTA Activity published three public documents and a variety of other publications in FY 2014. The titles, dates, and main authors are identified in Section 5.0. The Contract Managers, Corrective Action Unit (CAU) Leads, Preemptive Review (PER) Committee members, and Topical Committee members are listed by name and organization in Section 6.0. Other activities that affected UGTA quality are discussed in Section 7.0. Section 8.0 provides the FY 2014 UGTA QA program conclusions, and Section 9.0 lists the references not identified in Section 5.0.

  17. Quality assurance of C. perfringens epsilon toxoid vaccines--ELISA versus mouse neutralisation test.

    PubMed

    Rosskopf-Streicher, Ute; Volkers, Peter; Noeske, Kerstin; Werner, Esther

    2004-01-01

    Clostridium (C.) perfringens is a Gram-positive anaerobic spore-forming bacterium. Disease caused by C. perfringens infection is called enterotoxaemia. C. perfringens strains are classified on the basis of the lethal exotoxins formed by the bacteria. Epsilon toxin is one of the major lethal toxins and is formed by C. perfringens types B and D. C. perfringens is an ubiquitous bacterium. Infection occurs via food, water, animal litter or soil. Affected animals include mainly sheep, pigs and cattle. C. perfringens infection manifests as pulpy kidney disease and diarrhoea in suckling lambs. Enterotoxaemia development is peracute in most cases. Animals die suddenly while grazing on the pasture, without any prior signs of disease. Therefore, treatment is possible only in very rare cases. Suitable immunoprophylactic measures are the treatment of choice to combat the disease: Vaccines and immunosera have therefore been used extensively for a long time. The requirements for quality, efficacy and safety testing of the inactivated vaccines are laid down in the Ph. Eur. in the monograph: Clostridium perfringens vaccines for veterinary use. After a marketing authorisation is attained, the product batches must be tested in laboratory animal models for their potency against all vaccine components (Pharmeuropa, 1997). For potency testing (batch control) of C. perfringens types B and D, the induction of specific antibodies against epsilon toxin in rabbits must be verified. For this purpose, 10 rabbits are immunised twice with the product to be tested. Their blood is taken 14 days after the last immunisation and the serum is pooled. The pooled serum is then tested for its protective effect. This is done by means of the toxin neutralisation test in mice (optionally also in guinea pigs) in comparison with an international reference serum. The evaluation criterion is the death rate of the mice in the test and reference groups after administration of lethal doses of epsilon toxin. The

  18. Quality assurance program plan for Building 327

    SciTech Connect

    Tanke, J.M.

    1997-05-22

    This Quality Assurance Program Plan (QAPP) provides an overview of the quality assurance program for Building 327. The program applies to the facility safety structures, systems, and components and to activities that could affect safety structures, systems, and components. Adherence to the quality assurance program ensures the following: US Department of Energy missions and objectives are effectively accomplished; Products and services are safe, reliable, and meet or exceed the requirements and expectations of the user; Hazards to the public, to Hanford Site and facility workers, and to the environment are minimized. The format of this Quality Assurance Program Plan is structured to parallel that of 10 CFR 83 0.120, Quality Assurance Requirements. This Quality Assurance Program Plan (QAPP) provides information on how the Quality Assurance Program is implemented for the 324 Building B-Cell Safety Cleanout Project (BCCP). This QAPP is responsive to the Westinghouse Hanford Company Quality Assurance Program and Implementation Plan, WHC-SP 113 1, for 10 CFR 830.120, Nuclear Safety Management, Quality Assurance Requirements; and DOE Order 5700.6C, Quality Assurance. This QAPP supersedes PNNL PNL-MA-70 QAP Quality Assurance Plan No. WTC-050 Rev. 2, issue date May 3, 1996.

  19. 48 CFR 246.470 - Government contract quality assurance actions.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... quality assurance actions. 246.470 Section 246.470 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality Assurance 246.470 Government contract quality assurance actions....

  20. Versatile transceiver production and quality assurance

    NASA Astrophysics Data System (ADS)

    Olantera, L.; Detraz, S.; Sigaud, C.; Soos, C.; Troska, J.; Vasey, F.; Zeiler, M.

    2017-01-01

    The Versatile Link project has developed a radiation-hard optical link for LHC phase 1 detector upgrades. The project has reached its final stage and we have launched in 2016 the production of the Versatile Transceivers and Versatile Twin Transmitters. This paper provides an update of the production status and a detailed description and results of the quality assurance programme, which includes qualification and acceptance testing at CERN and production testing at the manufacturers' premises.

  1. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Quality assurance and quality control. 26.167 Section 26... Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance... calibrators and controls. (c) Quality control requirements for performing initial and confirmatory...

  2. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 1 2011-01-01 2011-01-01 false Quality assurance and quality control. 26.167 Section 26... Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance... calibrators and controls. (c) Quality control requirements for performing initial and confirmatory...

  3. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 1 2013-01-01 2013-01-01 false Quality assurance and quality control. 26.167 Section 26... Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance... calibrators and controls. (c) Quality control requirements for performing initial and confirmatory...

  4. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 1 2012-01-01 2012-01-01 false Quality assurance and quality control. 26.167 Section 26... Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance... calibrators and controls. (c) Quality control requirements for performing initial and confirmatory...

  5. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 1 2014-01-01 2014-01-01 false Quality assurance and quality control. 26.167 Section 26... Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance... calibrators and controls. (c) Quality control requirements for performing initial and confirmatory...

  6. Quality Assurance for Clinical Trials

    PubMed Central

    Ibbott, Geoffrey S.; Haworth, Annette; Followill, David S.

    2013-01-01

    Cooperative groups, of which the Radiation Therapy Oncology Group is one example, conduct national clinical trials that often involve the use of radiation therapy. In preparation for such a trial, the cooperative group prepares a protocol to define the goals of the trial, the rationale for its design, and the details of the treatment procedure to be followed. The Radiological Physics Center (RPC) is one of several quality assurance (QA) offices that is charged with assuring that participating institutions deliver doses that are clinically consistent and comparable. The RPC does this by conducting a variety of independent audits and credentialing processes. The RPC has compiled data showing that credentialing can help institutions comply with the requirements of a cooperative group clinical protocol. Phantom irradiations have been demonstrated to exercise an institution’s procedures for planning and delivering advanced external beam techniques (1–3). Similarly, RPC data indicate that a rapid review of patient treatment records or planning procedures can improve compliance with clinical trials (4). The experiences of the RPC are presented as examples of the contributions that a national clinical trials QA center can make to cooperative group trials. These experiences illustrate the critical need for comprehensive QA to assure that clinical trials are successful and cost-effective. The RPC is supported by grants CA 10953 and CA 81647 from the National Cancer Institute, NIH, DHHS. PMID:24392352

  7. A multilaboratory peer assessment quality assurance program-based evaluation of anticardiolipin antibody, and beta2-glycoprotein I antibody testing.

    PubMed

    Favaloro, Emmanuel J; Wong, Richard C W; Silvestrini, Roger; McEvoy, Robert; Jovanovich, Susan; Roberts-Thomson, Peter

    2005-02-01

    We evaluated the performance of anticardiolipin (aCL) and beta2-glycoprotein I (beta2-GPI) antibody assays through a large external quality assurance program. Data from the 2002 cycle of the Royal College of Pathologists of Australasia Quality Assurance Program (RCPA QAP) were analyzed for variation in reported numerical values and semiquantitative results or interpretations according to method type or group and in conjunction with available clinical data. High interlaboratory variation in numerical results and notable method-based variation, combined with a general lack of consensus in semiquantitative reporting, continues to be observed. Numerical results from cross-laboratory testing of 12 serum samples (for immunoglobulin G [IgG]-aCL, IgM-aCL, and IgG-beta2-GPI) yielded interlaboratory coefficients of variation (CVs) that were higher than 50% in six of 12 (50%) specimens for IgG-aCL, and 12 of 12 (100%) specimens for IgM-aCL and IgG-beta2-GPI. Semiquantitative reporting also varied considerably, with total (100%) consensus occurring in only four of 36 (11%) occasions. General consensus (where > 90% of participating laboratories agreed that a given serum sample gave a result of either negative or positive) was only obtained on 13 of 36 (36%) occasions. Variation in results between different method types or groups were also present, resulting in potential biasing of the RCPA QAP-defined target results by the large number of laboratories using the dominant aCL assays. Finally, laboratory findings frequently did not agree with the available clinical information. In conclusion, in a large proportion of specimens from the 2002 RCPA QAP cycle, laboratories could not agree on whether a serum sample tested was aCL-positive or aCL-negative, or beta2-GPI-positive or beta2-GPI-negative. Despite prior attempts to improve the standardization of testing and reporting practices, laboratory testing for aCL and anti-beta2-GPI still demonstrates significant interlaboratory and

  8. Quality assurance for gamma knives

    SciTech Connect

    Jones, E.D.; Banks, W.W.; Fischer, L.E.

    1995-09-01

    This report describes and summarizes the results of a quality assurance (QA) study of the Gamma Knife, a nuclear medical device used for the gamma irradiation of intracranial lesions. Focus was on the physical aspects of QA and did not address issues that are essentially medical, such as patient selection or prescription of dose. A risk-based QA assessment approach was used. Sample programs for quality control and assurance are included. The use of the Gamma Knife was found to conform to existing standards and guidelines concerning radiation safety and quality control of external beam therapies (shielding, safety reviews, radiation surveys, interlock systems, exposure monitoring, good medical physics practices, etc.) and to be compliant with NRC teletherapy regulations. There are, however, current practices for the Gamma Knife not covered by existing, formalized regulations, standards, or guidelines. These practices have been adopted by Gamma Knife users and continue to be developed with further experience. Some of these have appeared in publications or presentations and are slowly finding their way into recommendations of professional organizations.

  9. EPA Quality Assurance Policy Statement

    EPA Pesticide Factsheets

    This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  10. Quality assurance of the Applied Knowledge Test (AKT) of the MRCGP examination - an immediate post-test questionnaire evaluation of the candidates' views.

    PubMed

    Dixon, Hilton; Blow, Carol; Milne, Paul; Siriwardena, Niroshan; Milne, Heather; Elfes, Christopher

    2015-07-01

    The Applied Knowledge Test (AKT) of the Membership of the Royal College of General Practitioners (MRCGP) examination is a computer-based assessment delivered three times a year. A computerised questionnaire, administered immediately after the test, sought candidates' views as part of the test evaluation. Of 1681 candidates taking the test 1418 (84%) responded. Most candidates believed that the test assessed their knowledge of problems relevant to general practice. Their feedback highlighted areas where improvements could be made. Candidates' views of postgraduate specialty medical examinations in the UK are rarely sought or published. We are not aware of other published evidence. The use of computer-based testing enables immediate candidate feedback and can be used routinely to evaluate the test validity and formats. The views of candidates are an important component of quality assurance in reviewing the content, format and educational experience of a high-stakes examination.

  11. Quality assurance and quality control in clinical cytogenetics.

    PubMed

    Mikhail, Fady M; Watson, Michael S

    2014-07-14

    The goal of any clinical laboratory should be to provide patients with the most accurate test results possible. This is accomplished through various overlapping programs that continuously monitor and optimize all aspects of a test, including decisions by the laboratory to offer a test, the decision of providers to request the test, the testing itself, and the reporting of results to the referral source and patient. The levels at which test performance and accuracy can be optimized are encompassed under quality control (QC) and quality assurance (QA). The monitoring of QC and QA problems allows for the integration of these parameters into a total quality management program. This unit reviews QC and QA guidelines, in addition to discussing how to establish a quality assurance program.

  12. Quality Assurance: Patient Chart Reviews

    NASA Astrophysics Data System (ADS)

    Oginni, B. M.; Odero, D. O.

    2009-07-01

    Recent developments in radiation therapy have immensely impacted the way the radiation dose is delivered to patients undergoing radiation treatments. However, the fundamental quality assurance (QA) issues underlying the radiation therapy still remain the accuracy of the radiation dose and the radiation safety. One of the major duties of clinical medical physicists in the radiation therapy departments still revolves around ensuring the accuracy of dose delivery to the planning target volume (PTV), the reduction of unintended radiation to normal organs and minimization of the radiation exposure to the medical personnel based on ALARA (as low as reasonably achievable) principle. Many of the errors in radiation therapy can be minimized through a comprehensive program of periodic checks. One of the QA procedures on the patient comes in the form of chart reviews which could be in either electronic or paper-based format. We present the quality assurance procedures that have to be performed on the patient records from the beginning and periodically to the end of the treatment, based on the guidelines from the American Association of Physicists in Medicine (AAPM) and American College of Physicians (ACP).

  13. SU-E-T-745: The Use of Electron Dense Materials for Quality Assurance Testing in a Magnetic Field

    SciTech Connect

    Zijp, H van; Asselen, B van; Vries, W de; Ishakoglu, K; Beld, E; Kok, J; Wolthaus, J; Lagendijk, J; Raaymakers, B

    2015-06-15

    Purpose: Due to the effect of the magnetic field on the dose deposition (skewing the beam), machine quality assurance (QA) tests for the MR-linac (MRI combined with a linear accelerator) need to be redesigned. In this work we focus on the redesign of QA tests that address geometrical accuracy of the system. Methods: Using electron dense materials (e.g. copper in our experiment) the dose kernel is minimized and thereby the effect of the magnetic field on the dose distribution. This approach is supported by Monte-Carlo simulations and can be used in practice with film measurements. Two examples of QA tests are presented: beam profile and star-shot measurements. Results: The novel method was verified by performing both measurements on a conventional linac and the MR-linac with a film that was sandwiched between copper layers. Measurements were compared with a reference setup which was similar to setup used in clinical practice. On a conventional linac the experimental outcome showed good agreement between the reference and the new setup for both QA tests. The results from the MR-linac showed that the symmetry of the beam profile was restored in presence of the copper layers in the setup and that the isocenter size can be determined accurately with the introduced star-shot setup (see supporting material). Conclusion: The use of electron dense materials for QA tests was shown to be a simple and effective method to remove the effects on the dose distribution enabling assessment of geometrical accuracy of a MR-linac system. The use of high dense materials is not limited to the presented QA tests only, but has a broad applicability for beam specific QA tests in presence of a magnetic field.

  14. Automating linear accelerator quality assurance

    SciTech Connect

    Eckhause, Tobias; Thorwarth, Ryan; Moran, Jean M.; Al-Hallaq, Hania; Farrey, Karl; Ritter, Timothy; DeMarco, John; Pawlicki, Todd; Kim, Gwe-Ya; Popple, Richard; Sharma, Vijeshwar; Park, SungYong; Perez, Mario; Booth, Jeremy T.

    2015-10-15

    Purpose: The purpose of this study was 2-fold. One purpose was to develop an automated, streamlined quality assurance (QA) program for use by multiple centers. The second purpose was to evaluate machine performance over time for multiple centers using linear accelerator (Linac) log files and electronic portal images. The authors sought to evaluate variations in Linac performance to establish as a reference for other centers. Methods: The authors developed analytical software tools for a QA program using both log files and electronic portal imaging device (EPID) measurements. The first tool is a general analysis tool which can read and visually represent data in the log file. This tool, which can be used to automatically analyze patient treatment or QA log files, examines the files for Linac deviations which exceed thresholds. The second set of tools consists of a test suite of QA fields, a standard phantom, and software to collect information from the log files on deviations from the expected values. The test suite was designed to focus on the mechanical tests of the Linac to include jaw, MLC, and collimator positions during static, IMRT, and volumetric modulated arc therapy delivery. A consortium of eight institutions delivered the test suite at monthly or weekly intervals on each Linac using a standard phantom. The behavior of various components was analyzed for eight TrueBeam Linacs. Results: For the EPID and trajectory log file analysis, all observed deviations which exceeded established thresholds for Linac behavior resulted in a beam hold off. In the absence of an interlock-triggering event, the maximum observed log file deviations between the expected and actual component positions (such as MLC leaves) varied from less than 1% to 26% of published tolerance thresholds. The maximum and standard deviations of the variations due to gantry sag, collimator angle, jaw position, and MLC positions are presented. Gantry sag among Linacs was 0.336 ± 0.072 mm. The

  15. Proficiency test: a quality assurance method for high-purity gamma spectrometry system

    NASA Astrophysics Data System (ADS)

    Radulescu, Ileana; Romeo Calin, Marian

    2014-03-01

    As part of the implementation of the quality system on ISO 17025 and accreditation, SALROM laboratory participated in the last year in intercomparison exercises, national and international, for determination of natural and man-made radionuclides. This paper describes results obtained in intercomparison exercise organized by IAEA in 2011. The reported values were mostly in good agreement with the resulting reference values.

  16. Establishment of quality assurance procedures for aquatic toxicity testing with the nematode Caenorhabditis elegans

    SciTech Connect

    Freeman, M.N.; Marse, T.J.; Williams, P.L.

    1998-12-31

    In this study initial data were generated to develop laboratory control charts for aquatic toxicity testing using the nematode Caenorhabditis elegans. Tests were performed using two reference toxicants: CdCl{sub 2} and CuCl{sub 2}. All tests were performed for 24 h without a food source and of 48 h with a food source in a commonly used nematode aquatic medium. Each test was replicated 6 times with each replicate having 6 wells per concentration with 10 {+-} 1 worms per well. Probit analysis was used to estimate LC{sub 50} values for each test. The data were used to construct a mean ({bar x}) laboratory control chart for each reference toxicant. The coefficient of variation (CV) for three of the four reference toxicant tests was less than 20%, which demonstrates an excellent degree of reproducibility. These CV values are well within suggested standards for determination of organism sensitivity and overall test system credibility. A standardized procedure for performing 24 h and 48 h aquatic toxicity studies with C. elegans is proposed.

  17. Quality-assurance tests of five Y-12 Kevlar-49 spools used to fabricate strands and reliability specimens for stress-rupture tests

    SciTech Connect

    Caley, L.E.; Ambalal, P.K.; Carley, J.F.; Ford, T.S.; Moore, R.L.; Noecker, D.J.; Ross, M.E.; Sherry, R.J.; Yoshiyama, J.M.

    1984-05-07

    An important component of the composite reliability program is the assurance of quality of Kevlar 49, 380-denier yarn and epoxy-impregnated yarn. This yarn, which is used in the fabrication of W-82 components from Kevlar 49/epoxy composites, is also formed into test specimens for long-term, stress-rupture studies and reliability studies. The QA work covered in this report encompasses preparation of impregnated-yarn specimens, examination of the yarn itself and individual fibers therefrom, tensile testing of bare and impregnated yarns and heat-degraded yarns. The yarn samples were all drawn from spools of 380-denier Kevlar 49 shipped to LLNL from Y-12. The resin matrix is an amine-hardened epoxy with low viscosity and long pot life, intended for filament winding. The components are Dow epoxy resin (DER) 332 and Jeffamine T-403 triamine hardener. The stoichiometric combining ratio, which we used in our work, is 100 parts by weight resin to 44 parts hardener. Quality-assurance testing not only verifies that the yarns actually meet the manufacturer's specifications, but also provides data on the relationships between fiber characteristics and the lifetime reliability of fabricated items.

  18. Quality Assurance in Chinese Higher Education

    ERIC Educational Resources Information Center

    Li, Yuan

    2010-01-01

    Quality assurance has been integrated into the fabric of higher education in China, with the issue of quality in higher education--how to evaluate it and how to enhance it--now taking centre stage in Chinese higher education. In the past decade, the development of quality assurance in Chinese higher education has covered a broad spectrum of…

  19. References on EPA Quality Assurance Project Plans

    EPA Pesticide Factsheets

    Provides requirements for the conduct of quality management practices, including quality assurance (QA) and quality control (QC) activities, for all environmental data collection and environmental technology programs performed by or for this Agency.

  20. [Quality and quality assurance, a European problem].

    PubMed

    Schmitt, H

    1994-01-01

    The problem of quality and quality assurance for the free exchange of blood and blood products in Europe is discussed. The background of all discussion of quality is the categorical theory of Aristoteles. The philosophical basis is described. The fundamental law of the daily work of a blood center has to be a philosophy of quality which depends on the sociodemographic situation in the region. This basic varies from country to country in Europe. The importance of the supranational bodies in Europe is mentioned. The weightness of the Code of Ethics is discussed. Virus safety, purity and validity of blood and blood products are described as parameters of the quality aspects. Finally it is confirmed that a well running blood program is a multicategorical problem.

  1. Compilation of Quality Assurance Documentation for Analyses Performed for the Resumption of Transient Testing Environmental Assessment

    SciTech Connect

    Annette L. Schafer; A. Jeffrey Sondrup

    2013-11-01

    This is a companion document to the analyses performed in support of the environmental assessment for the Resumption of Transient Fuels and Materials Testing. It is provided to allow transparency of the supporting calculations. It provides computer code input and output. The basis for the calculations is documented separately in INL (2013) and is referenced, as appropriate. Spreadsheets used to manipulate the code output are not provided.

  2. Progress Toward Quality Assurance Standards for Advanced Hydrocarbon Fuels Based on Thermal Performance Testing and Chemometric Modeling

    DTIC Science & Technology

    2015-12-15

    Conference Paper 3. DATES COVERED (From - To) 13 Nov 2015 – 15 Dec 2015 4. TITLE AND SUBTITLE Progress Toward Quality Assurance Standards For...UNIT NUMBER Q0A4 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NO. Air Force Research...MONITOR’S ACRONYM(S) Air Force Research Laboratory (AFMC) AFRL/RQR 11. SPONSOR/MONITOR’S REPORT 5 Pollux Drive NUMBER(S) Edwards AFB, CA

  3. DEMONSTRATION AND QUALITY ASSURANCE PROJECT ...

    EPA Pesticide Factsheets

    The demonstration of technologies for determining the presence of dioxin in soil and sediment is being conducted under the U.S. Environmental Protection Agency Superfund Innovative Technology Evaluation Program in Saginaw, Michigan, at Green Point Environmental Learning Center from approximately April 26 to May 6, 2004. The primary purpose of the demonstration is to evaluate innovative monitoring technologies. The technologies listed below will be demonstrated. .AhRC PCRTM Kit, Hybrizyme Corporation .Ah-IMMUNOASSY@ Kit, Paralsian, Inc. .Coplanar PCB Immunoassay Kit, Abraxis LLC .DF-l Dioxin/Furan Immunoassay Kit, CAPE Technologies L.L.C. .CALUX@ by Xenobiotic Detection Systems, Inc- .Dioxin ELISA Kit, Wako Pure Chemical Industries LTD. This demonstration plan describes the procedures that will be used to verify the performance and cost of these technologies. The plan incorporates the quality assurance and quality control elements needed to generate data of sufficient quality to document each technology's performance and cost. A separate innovative technology verification report (ITVR) will.be prepared for each technology. The ITVRs will present the demonstration findings associated with the demonstration objectives. The objective of this program is to promote the acceptance and use of innovative field technologies by providing well-documented performance and cost data obtained from field demonstrations.

  4. Quality assurance in film radiography

    SciTech Connect

    Van Bellegem, L.; Vaessen, B.

    1993-12-31

    The ISO 9000 standards were originally developed during the 1980`s to provide uniform, worldwide quality assurance requirements. The EC (European Communities) adopted these standards as part of their modular approach to ``conformity assessment`` procedures, for several product categories. This includes the development of standards (specifications) which define what the purchaser wants and what the supplier agrees to provide, as well as quality system registration (certification) which increases confidence in the supplier`s ability to produce consistently. The requirements are typically most rigorous for regulated products that have a major impact on health and safety i.e film radiographic systems. This is the main reason for making available the necessary Q.C. tools in film radiography to comply with Q.A. specifications and guarantee the required consistent performance. These tools can only give satisfying support if they are dedicated, easy to use, precise and cost effective at the user`s level. The main topics for such a Q.A. package are: (1) standard for Film System classification for industrial radiography; (2) film system certification; and (3) standard for control of film processing by means of reference values i.e. pre-exposed film wedges and archiving quality control method.

  5. FIELD DEMONSTRATION AND QUALITY ASSURANCE ...

    EPA Pesticide Factsheets

    The Demonstration of innovative field devices for the measurement of mercury in soil and sediment is being conducted under the EPA's SITE Program in February 2003 at the United States Department of Energy's (DOE) Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee and the Tennessee Department of Environment and Conservation's Department of Energy Oversight facility in Oak Ridge, Tennessee. The primary purpose of the Demonstration is to evaluate innovative field devices for the measurement of mercury in soil and sediment based on their performance and cost as compared to a conventional, off-site laboratory analytical method. The five field measurement devices listed below will be demonstrated: .Metorex's X-M ET 2000 Metal Master Analyzer, X-Ray Fluorescence Analyzer .Milestone Inc.'s Direct Mercury Analyzer (DMA-80), Thermal Decomposition Instrument.NITON's XL-700 Series Multi-Element Analyzer, X-Ray Fluorescence Analyzer .Ohio Lumex's RA-915+ Portable Mercury Analyzer, Atomic Absorption Spectrometer, Thermal Decompostion Attachment RP 91C .MTI, Inc.'s PDV 5000 Hand Held Instrument, Anodic Stripping Voltamm eter<1). This Demonstration Plan describes the procedures that will be used to verify the performance and cost of each field measurement device. The plan incorporates the quality assurance and quality control elements needed to generate data of sufficient quality to document each device's performance and cost. A separate Innovative Technology Verifica

  6. DEMONSTRATION AND QUALITY ASSURANCE PROJECT ...

    EPA Pesticide Factsheets

    A demonstration of field portable/mobile technologies for measuring trace elements in soil and sediments was conducted under the U.S. Environmental Protection Agency Superfund Innovative Technology Evaluation (SITE) Program. The demonstration took place from January 24 to 28, 2005, at the Kennedy Athletic, Recreational and Social Park at Kennedy Space Center on Merritt Island, Florida. The purpose of the demonstration was to verify the performance of various instruments that employ X-ray fluorescence (XRF) measurement technologies for the determination of 13 toxic elements in a variety of soil and sediment samples. Instruments from the technology developers listed below were demonstrated. o Innov-X Systems, Inc.o NITON LLC (2 instruments ) o Oxford Instruments Portable Division (formerly Metorex, Inc.) .Oxford Instruments Analytical .Rigaku, Inc.o RONTEC USA Inc.o Xcalibur XRF Services Inc. (Division of Elvatech Ltd. ) This demonstration plan describes the procedures that will be used to verify the performance and cost of the XRF instruments provided by these technology developers. The plan incorporates the quality assurance and quality control elements needed to generate data of sufficient quality to perform this verification. A separate innovative technology verification report (ITVR) will be prepared for each instrument. The objective of this program is to promote the acceptance and use of innovative field technologies by providing well-documented perfor

  7. Professionalism, Profession and Quality Assurance Practitioners in External Quality Assurance Agencies in Higher Education

    ERIC Educational Resources Information Center

    Cheung, Jordan C. M.

    2015-01-01

    This article seeks to spark a dialectic discussion on the establishment of a set of professional competencies for quality assurance practitioners who serve in external quality assurance agencies in higher education. Such a need is identified due to the shortage of relevant and sufficient coverage in the quality assurance literature. To…

  8. Quality assurance from a manufacturer's standpoint

    NASA Astrophysics Data System (ADS)

    Anderson, William J.

    1991-05-01

    The efforts of a manufacturer in the area of component procurement acceptance testing are very visible, while the quality assurance work that goes on during the design and manufacture of medical imaging equipment is frequently not so apparent. Many steps in the design and production of imaging devices are carefully designed to promote not only quality of the devices when initially installed, but also the ability to maintain the device''s quality over a period of time. Customer requirements for aesthetics, performance, safety and regulatory compliance must be considered. Software, which represents over 70 of the design engineering of modern products, presents a special challenge since the quality of software cannot be tested and must be designed in. Specific hardware elements such as monitor phosphor color and uniformity deserve extra consideration. A design that allows quick diagnosis and replacement of failed components is also important.

  9. Valid methods: the quality assurance of test method development, validation, approval, and transfer for veterinary testing laboratories.

    PubMed

    Wiegers, Ann L

    2003-07-01

    Third-party accreditation is a valuable tool to demonstrate a laboratory's competence to conduct testing. Accreditation, internationally and in the United States, has been discussed previously. However, accreditation is only I part of establishing data credibility. A validated test method is the first component of a valid measurement system. Validation is defined as confirmation by examination and the provision of objective evidence that the particular requirements for a specific intended use are fulfilled. The international and national standard ISO/IEC 17025 recognizes the importance of validated methods and requires that laboratory-developed methods or methods adopted by the laboratory be appropriate for the intended use. Validated methods are therefore required and their use agreed to by the client (i.e., end users of the test results such as veterinarians, animal health programs, and owners). ISO/IEC 17025 also requires that the introduction of methods developed by the laboratory for its own use be a planned activity conducted by qualified personnel with adequate resources. This article discusses considerations and recommendations for the conduct of veterinary diagnostic test method development, validation, evaluation, approval, and transfer to the user laboratory in the ISO/IEC 17025 environment. These recommendations are based on those of nationally and internationally accepted standards and guidelines, as well as those of reputable and experienced technical bodies. They are also based on the author's experience in the evaluation of method development and transfer projects, validation data, and the implementation of quality management systems in the area of method development.

  10. Exploring Quality Assurance in Sixth Form Colleges

    ERIC Educational Resources Information Center

    Stoten, David William

    2012-01-01

    Purpose: This paper aims to focus on the changing nature of quality assurance systems within the sixth form college sector. Design/methodology/approach: Ten sixth form colleges were surveyed across England and staff from varying levels within college hierarchies questioned about how quality assurance systems were implemented. Research involved…

  11. Teacher Reaction to ICP Quality Assurance Procedures.

    ERIC Educational Resources Information Center

    Leonard, Ann

    An integral part of the Quality Assurance Manual developed by Southwest Regional Laboratory (SWRL) to accompany the Kindergarten Program is the end-of-program assessment of the Instructional Concepts Program (ICP). Following completion of ICP Quality Assurance assessment, four teachers were interviewed in order to gather information pertinent to…

  12. 7 CFR 652.7 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 6 2011-01-01 2011-01-01 false Quality assurance. 652.7 Section 652.7 Agriculture... AGRICULTURE SUPPORT ACTIVITIES TECHNICAL SERVICE PROVIDER ASSISTANCE General Provisions § 652.7 Quality assurance. (a) NRCS will review, in consultation with the Farm Service Agency, as appropriate, the...

  13. 7 CFR 652.7 - Quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 6 2013-01-01 2013-01-01 false Quality assurance. 652.7 Section 652.7 Agriculture... AGRICULTURE SUPPORT ACTIVITIES TECHNICAL SERVICE PROVIDER ASSISTANCE General Provisions § 652.7 Quality assurance. (a) NRCS will review, in consultation with the Farm Service Agency, as appropriate, the...

  14. 48 CFR 2453.246 - Quality Assurance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 6 2014-10-01 2014-10-01 false Quality Assurance. 2453.246 Section 2453.246 Federal Acquisition Regulations System DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT CLAUSES AND FORMS FORMS Prescription of Forms 2453.246 Quality Assurance....

  15. 7 CFR 652.7 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 6 2010-01-01 2010-01-01 false Quality assurance. 652.7 Section 652.7 Agriculture... AGRICULTURE SUPPORT ACTIVITIES TECHNICAL SERVICE PROVIDER ASSISTANCE General Provisions § 652.7 Quality assurance. (a) NRCS will review, in consultation with the Farm Service Agency, as appropriate, the...

  16. 48 CFR 2453.246 - Quality Assurance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Quality Assurance. 2453.246 Section 2453.246 Federal Acquisition Regulations System DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT CLAUSES AND FORMS FORMS Prescription of Forms 2453.246 Quality Assurance....

  17. 7 CFR 652.7 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 6 2014-01-01 2014-01-01 false Quality assurance. 652.7 Section 652.7 Agriculture... AGRICULTURE SUPPORT ACTIVITIES TECHNICAL SERVICE PROVIDER ASSISTANCE General Provisions § 652.7 Quality assurance. (a) NRCS will review, in consultation with the Farm Service Agency, as appropriate, the...

  18. 7 CFR 652.7 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 6 2012-01-01 2012-01-01 false Quality assurance. 652.7 Section 652.7 Agriculture... AGRICULTURE SUPPORT ACTIVITIES TECHNICAL SERVICE PROVIDER ASSISTANCE General Provisions § 652.7 Quality assurance. (a) NRCS will review, in consultation with the Farm Service Agency, as appropriate, the...

  19. 48 CFR 2453.246 - Quality Assurance.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Quality Assurance. 2453.246 Section 2453.246 Federal Acquisition Regulations System DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT CLAUSES AND FORMS FORMS Prescription of Forms 2453.246 Quality Assurance....

  20. 48 CFR 2453.246 - Quality Assurance.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 6 2013-10-01 2013-10-01 false Quality Assurance. 2453.246 Section 2453.246 Federal Acquisition Regulations System DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT CLAUSES AND FORMS FORMS Prescription of Forms 2453.246 Quality Assurance....

  1. 48 CFR 2453.246 - Quality Assurance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false Quality Assurance. 2453.246 Section 2453.246 Federal Acquisition Regulations System DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT CLAUSES AND FORMS FORMS Prescription of Forms 2453.246 Quality Assurance....

  2. Quality assurance manual: Volume 2, Appendices

    SciTech Connect

    Oijala, J.E.

    1988-06-01

    This paper contains quality assurance information on departments of the Stanford Linear Accelerator Center. Particular quality assurance policies and standards discussed are on: Mechanical Systems; Klystron and Microwave Department; Electronics Department; Plant Engineering; Accelerator Department; Purchasing; and Experimental Facilities Department. (LSP)

  3. Quality Assurance Reconsidered: A Case Study

    ERIC Educational Resources Information Center

    Gynnild, Vidar

    2007-01-01

    This article examines an external evaluation of the quality assurance system at the Norwegian University of Science and Technology (NTNU) conducted by The Norwegian Agency for Quality Assurance in Higher Education (NOKUT). The external audit report along with internal reports provided by the seven faculties of the university served as the major…

  4. Quality Assurance in Sub-Saharan Africa

    ERIC Educational Resources Information Center

    Materu, Peter; Righetti, Petra

    2010-01-01

    This article assesses the status and practice of higher education quality assurance in sub-Saharan Africa, focusing on degree-granting tertiary institutions. A main finding is that structured national-level quality assurance processes in African higher education are a very recent phenomenon and that most countries face major capacity constraints.…

  5. Ontario's Quality Assurance Framework: A Critical Response

    ERIC Educational Resources Information Center

    Heap, James

    2013-01-01

    Ontario's Quality Assurance Framework (QAF) is reviewed and found not to meet all five criteria proposed for a strong quality assurance system focused on student learning. The QAF requires a statement of student learning outcomes and a method and means of assessing those outcomes, but it does not require that data on achievement of intended…

  6. Evaluation of Quality Assurance Programs for Externships.

    ERIC Educational Resources Information Center

    Ruskiewicz, Joseph

    1982-01-01

    The procedures of the Pennsylvania College of Optometry's Office of External Educational Programs are reviewed to show how quality assurance techniques can be categorized. The format was designed to evaluate quality assurance procedures for both the educational and service aspects of eye care. (MLW)

  7. [Quality assurance in acupuncture therapy].

    PubMed

    Kubiena, G

    1996-04-01

    Quality assurance for acupuncture therapy requires a good basic and on-going training in both conventional western medicine as well as in the theory and practice of acupuncture, the ability to synthesize the patient's objective findings and subjective feelings, and honesty with the patient and towards oneself. Thus, based on the continuous critical evaluation of the objective and subjective parameters, the question of acupunture as the optimal form of therapy for this specific case is honestly answered and one has the courage to admit failures. With regard to the theory, surveys of the acupuncture literature show that a considerable improvement in quality and honesty is necessary. There is a lack of standardised experimental methods (e.g. 28 different placebos in 28 different studies!). Especially German acupuncture journals have a disturbed relation to failures. To hide or deny failures is of no benefit neither to acupuncture, science to the relationship between the physician and the patient since the practitioner must be able to rely on the information in the literature. Furthermore, one should be open minded to alternative methods even if this means to refer a patient to a colleague.

  8. Quality Assurance Planning for Region 6

    EPA Pesticide Factsheets

    The ultimate success of an environmental program or project depends on the quality of the environmental data collected and used in decision-making. EPA has developed guidances to help state and tribal governments develop Quality Assurance Program Plans.

  9. The Concepts of Quality, Quality Assurance and Quality Enhancement

    ERIC Educational Resources Information Center

    Elassy, Noha

    2015-01-01

    Purpose: This paper aims to critically review and discuss different definitions of the concepts of quality, quality assurance (QA) and quality enhancement (QE) in higher education (HE) with presenting critical perspectives of the literature. Design/methodology/approach: The paper looks at literature concerns with the meaning of quality, QA and QE,…

  10. Training, Quality Assurance Factors, and Tools Investigation: a Work Report and Suggestions on Software Quality Assurance

    NASA Technical Reports Server (NTRS)

    Lee, Pen-Nan

    1991-01-01

    Previously, several research tasks have been conducted, some observations were obtained, and several possible suggestions have been contemplated involving software quality assurance engineering at NASA Johnson. These research tasks are briefly described. Also, a brief discussion is given on the role of software quality assurance in software engineering along with some observations and suggestions. A brief discussion on a training program for software quality assurance engineers is provided. A list of assurance factors as well as quality factors are also included. Finally, a process model which can be used for searching and collecting software quality assurance tools is presented.

  11. The Columbia River Protection Supplemental Technologies Quality Assurance Project Plan

    SciTech Connect

    Fix, N. J.

    2007-01-10

    The U.S. Department of Energy (DOE) has conducted interim groundwater remedial activities on the Hanford Site since the mid-1990s for several groundwater contamination plumes. DOE established the Columbia River Protection Supplemental Technologies Project (Technologies Project) in 2006 to evaluate alternative treatment technologies. The objectives for the technology project are as follows: develop a 300 Area polyphosphate treatability test to immobilize uranium, design and test infiltration of a phosphate/apatite technology for Sr-90 at 100-N, perform carbon tetrachloride and chloroform attenuation parameter studies, perform vadose zone chromium characterization and geochemistry studies, perform in situ biostimulation of chromium studies for a reducing barrier at 100-D, and perform a treatability test for phytoremediation for Sr-90 at 100-N. This document provides the quality assurance guidelines that will be followed by the Technologies Project. This Quality Assurance Project Plan is based on the quality assurance requirements of DOE Order 414.1C, Quality Assurance, and 10 CFR 830, Subpart A--Quality Assurance Requirements as delineated in Pacific Northwest National Laboratory’s Standards-Based Management System. In addition, the technology project is subject to the Environmental Protection Agency (EPA) Requirements for Quality Assurance Project Plans (EPA/240/B-01/003, QA/R-5). The Hanford Analytical Services Quality Assurance Requirements Documents (HASQARD, DOE/RL-96-68) apply to portions of this project and to the subcontractors. HASQARD requirements are discussed within applicable sections of this plan.

  12. SWiFT Software Quality Assurance Plan.

    SciTech Connect

    Berg, Jonathan Charles

    2016-01-01

    This document describes the software development practice areas and processes which contribute to the ability of SWiFT software developers to provide quality software. These processes are designed to satisfy the requirements set forth by the Sandia Software Quality Assurance Program (SSQAP). APPROVALS SWiFT Software Quality Assurance Plan (SAND2016-0765) approved by: Department Manager SWiFT Site Lead Dave Minster (6121) Date Jonathan White (6121) Date SWiFT Controls Engineer Jonathan Berg (6121) Date CHANGE HISTORY Issue Date Originator(s) Description A 2016/01/27 Jon Berg (06121) Initial release of the SWiFT Software Quality Assurance Plan

  13. 48 CFR 37.604 - Quality assurance surveillance plans.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Quality assurance... assurance surveillance plans. Requirements for quality assurance and quality assurance surveillance plans are in Subpart 46.4. The Government may either prepare the quality assurance surveillance plan...

  14. Assuring quality in high-consequence engineering

    SciTech Connect

    Hoover, Marcey L.; Kolb, Rachel R.

    2014-03-01

    In high-consequence engineering organizations, such as Sandia, quality assurance may be heavily dependent on staff competency. Competency-dependent quality assurance models are at risk when the environment changes, as it has with increasing attrition rates, budget and schedule cuts, and competing program priorities. Risks in Sandia's competency-dependent culture can be mitigated through changes to hiring, training, and customer engagement approaches to manage people, partners, and products. Sandia's technical quality engineering organization has been able to mitigate corporate-level risks by driving changes that benefit all departments, and in doing so has assured Sandia's commitment to excellence in high-consequence engineering and national service.

  15. Principles and Practices for Quality Assurance and Quality Control

    USGS Publications Warehouse

    Jones, Berwyn E.

    1999-01-01

    Quality assurance and quality control are vital parts of highway runoff water-quality monitoring projects. To be effective, project quality assurance must address all aspects of the project, including project management responsibilities and resources, data quality objectives, sampling and analysis plans, data-collection protocols, data quality-control plans, data-assessment procedures and requirements, and project outputs. Quality control ensures that the data quality objectives are achieved as planned. The historical development and current state of the art of quality assurance and quality control concepts described in this report can be applied to evaluation of data from prior projects.

  16. Current practices in endotoxin and pyrogen testing in biotechnology. The Quality Assurance/Quality Control Task Group. Parenteral Drug Association

    SciTech Connect

    Not Available

    1990-01-01

    This article presents the results of a nationwide survey of the biotechnology industry regarding endotoxin and pyrogen testing and control. It identifies procedures and methods being used by biotechnology companies, and firms working with biotechnology products, in the testing for and detection of endotoxin and other pyrogenic substances. The review attempts to identify areas of commonality and standardization within the industry and includes topics for discussion at the end of the survey results.

  17. Quality assurance in UK higher education

    NASA Astrophysics Data System (ADS)

    Shrimplin, Valerie

    Quality Assurance methods are becoming increasingly well known as systems applicable in business, commerce and industry. In modified form, such concepts can be applied to higher education and, in the UK, quality systems are utilized in universities in order to ensure the quality of provision and standards of awards. Similar principles may also be applied to the evaluation of quality in research.

  18. 40 CFR 51.363 - Quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... impede program performance. The quality assurance and quality control procedures shall be periodically...) Equipment audits. During overt site visits, auditors shall conduct quality control evaluations of the... at least as accurate as those required for regular equipment quality control and comparing...

  19. 40 CFR 51.363 - Quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... impede program performance. The quality assurance and quality control procedures shall be periodically...) Equipment audits. During overt site visits, auditors shall conduct quality control evaluations of the... at least as accurate as those required for regular equipment quality control and comparing...

  20. 40 CFR 136.7 - Quality assurance and quality control.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Quality assurance and quality control... assurance and quality control. The permittee/laboratory shall use suitable QA/QC procedures when conducting... quality control elements, where applicable, into the laboratory's documented standard operating...

  1. 40 CFR 136.7 - Quality assurance and quality control.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Quality assurance and quality control... assurance and quality control. The permittee/laboratory shall use suitable QA/QC procedures when conducting... quality control elements, where applicable, into the laboratory's documented standard operating...

  2. 40 CFR 136.7 - Quality assurance and quality control.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Quality assurance and quality control... assurance and quality control. The permittee/laboratory shall use suitable QA/QC procedures when conducting... quality control elements, where applicable, into the laboratory's documented standard operating...

  3. Internal Quality Assurance Program for ERBB2 (HER2) Testing Improves the Selection of Breast Cancer Patients for Treatment with Trastuzumab.

    PubMed

    Martin, Vittoria; Camponovo, Antonella; Ghisletta, Morena; Bongiovanni, Massimo; Mazzucchelli, Luca

    2012-01-01

    International guidelines for ERBB2 (HER2) testing procedures in breast cancer patients highlight the importance of external quality control. In contrast, internal quality assurance programs have been poorly defined, and their clinical significance has not yet been investigated. We developed a quality assurance scheme by performing HER2 FISH on 724 patients randomly selected out of 1996 patients with breast cancer presenting at our institute. We collected samples monthly for tissue microarray analysis and correlated HER2 gene status with IHC scores. The concordance was excellent (κ = 0.92, P < 0.0001). HER2 amplification characterized 25% of score 2+ but also 13% of score 1+, thus expanding the number of patients eligible for trastuzumab. Based on these findings, the FISH test is now recommended at our institution for score 1+ and 2+ patients. Adherence to internal assurance program improves patient selection and may lead to the definition of in-house tailored diagnostic algorithms different from those proposed in international guidelines.

  4. Quality Assurance Project Plan Development Tool

    EPA Pesticide Factsheets

    This tool contains information designed to assist in developing a Quality Assurance (QA) Project Plan that meets EPA requirements for projects that involve surface or groundwater monitoring and/or the collection and analysis of water samples.

  5. [Health care quality assurance in the Netherlands].

    PubMed

    Reerink, E

    1990-01-01

    In this paper the main structural features of the dutch health system are described, together with a historical survey of its development in recent years. The basic elements of quality assurance in the country are also discussed.

  6. 40 CFR 31.45 - Quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND COOPERATIVE AGREEMENTS TO STATE AND LOCAL GOVERNMENTS Post-Award Requirements Reports, Records, Retention, and Enforcement § 31.45 Quality assurance. If the grantee's...

  7. 40 CFR 31.45 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND COOPERATIVE AGREEMENTS TO STATE AND LOCAL GOVERNMENTS Post-Award Requirements Reports, Records, Retention, and Enforcement § 31.45 Quality assurance. If the grantee's...

  8. Quality assurance program for isotopic power systems

    NASA Astrophysics Data System (ADS)

    Hannigan, R. L.; Harnar, R. R.

    1982-12-01

    The Sandia National Laboratories Quality Assurance Program that applies to non-weapon (reimbursable) Radioisotopic Thermoelectric Generators is summarized. The program was implemented over the past 16 years on power supplies used in various space and terrestrial systems. The quality assurance (QA) activity of the program is in support of the Department of Energy, Office of Space Nuclear Projects. Basic elements of the program are described and examples of program documentation are presented.

  9. Quality assurance program for isotopic power systems

    SciTech Connect

    Hannigan, R.L.; Harnar, R.R.

    1982-12-01

    This report summarizes the Sandia National Laboratories Quality Assurance Program that applies to non-weapon (reimbursable) Radioisotopic Thermoelectric Generators. The program has been implemented over the past 16 years on power supplies used in various space and terrestrial systems. The quality assurance (QA) activity of the program is in support of the Department of Energy, Office of Space Nuclear Projects. Basic elements of the program are described in the report and examples of program decumentation are presented.

  10. Marshall Island radioassay quality assurance program an overview

    SciTech Connect

    Conrado, C.L.; Hamilton, T.F.; Kehl, S.R.; Robison, W.L.; Stoker, A.C.

    1998-09-01

    The Lawrence Livermore National Laboratory has developed an extensive quality assurance program to provide high quality data and assessments in support of the Marshall Islands Dose Assessment and Radioecology Program. Our quality assurance objectives begin with the premise of providing integrated and cost-effective program support (to meet wide-ranging programmatic needs, scientific peer review, litigation defense, and build public confidence) and continue through from design and implementation of large-scale field programs, sampling and sample preparation, radiometric and chemical analyses, documentation of quality assurance/quality control practices, exposure assessments, and dose/risk assessments until publication. The basic structure of our radioassay quality assurance/quality control program can be divided into four essential elements; (1) sample and data integrity control; (2) instrument validation and calibration; (3) method performance testing, validation, development and documentation; and (4) periodic peer review and on-site assessments. While our quality assurance objectives are tailored towards a single research program and the evaluation of major exposure pathways/critical radionuclides pertinent to the Marshall Islands, we have attempted to develop quality assurance practices that are consistent with proposed criteria designed for laboratory accre

  11. 10 CFR 71.101 - Quality assurance requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... perform satisfactorily in service. Quality assurance includes quality control, which comprises those... 10 Energy 2 2010-01-01 2010-01-01 false Quality assurance requirements. 71.101 Section 71.101... Quality Assurance § 71.101 Quality assurance requirements. (a) Purpose. This subpart describes...

  12. 10 CFR 71.105 - Quality assurance program.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Quality assurance program. 71.105 Section 71.105 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality... which functional compliance can be demonstrated by inspection or test; and (5) The quality history...

  13. 10 CFR 71.105 - Quality assurance program.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Quality assurance program. 71.105 Section 71.105 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality... which functional compliance can be demonstrated by inspection or test; and (5) The quality history...

  14. 10 CFR 71.105 - Quality assurance program.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Quality assurance program. 71.105 Section 71.105 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality... which functional compliance can be demonstrated by inspection or test; and (5) The quality history...

  15. 10 CFR 71.105 - Quality assurance program.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Quality assurance program. 71.105 Section 71.105 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality... which functional compliance can be demonstrated by inspection or test; and (5) The quality history...

  16. 10 CFR 71.105 - Quality assurance program.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Quality assurance program. 71.105 Section 71.105 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality... which functional compliance can be demonstrated by inspection or test; and (5) The quality history...

  17. 10 CFR 63.142 - Quality assurance criteria.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... specifications, met by the purchased material and equipment. (3) The effectiveness of the control of quality by... functions of these organizations. The quality assurance program must control activities affecting the... controls, processes, test equipment, tools, and skills to attain the required quality, and the need...

  18. Instructional Quality Assurance at Lansing Community College.

    ERIC Educational Resources Information Center

    Herder, Dale M.; And Others

    Drawing from the experiences of Lansing Community College (LCC), this paper offers a rationale and model for measuring instructional quality. Section I offers background on LCC's efforts to assess the quality of its courses and curricula, and to introduce such quality assurance procedures as computer-based course syllabi, department and program…

  19. Comparability of antimicrobial susceptibility test results from 22 European countries and Israel: an external quality assurance exercise of the European Antimicrobial Resistance Surveillance System (EARSS) in collaboration with the United Kingdom National External Quality Assurance Scheme (UK NEQAS).

    PubMed

    Bronzwaer, S; Buchholz, U; Courvalin, P; Snell, J; Cornaglia, G; de Neeling, A; Aubry-Damon, H; Degener, J

    2002-12-01

    The goal of this exercise was to organize external quality assurance (QA) of antibiotic susceptibility testing for laboratories participating in EARSS and to assess the comparability of susceptibility test results across countries, and guidelines. In September 2000, UK NEQAS distributed a set of three Streptococcus pneumoniae strains, two Staphylococcus aureus strains and one Streptococcus haemolyticus strain. Laboratories reported the guideline followed, the interpretation of the susceptibility test result and the MIC, if tested. In this study we considered results 'concordant' if the reported interpretation of the participating laboratory agreed with the designated interpretation of reference laboratories. Overall, 433 (92%) of 471 laboratories from 23 countries reported back. Of the 8685 tests that were assessed, 8322 (96%) were interpreted correctly by the participants. Concordance for detection of penicillin non-susceptibility in the three S. pneumoniae strains was 96%, 90% and 87%, respectively. Laboratories performed extremely well in detecting oxacillin resistance in the homogeneously methicillin-resistant S. aureus (MRSA) strain, but the concordance rate dropped from 100% to 77% in the heterogeneously resistant MRSA strain. Concordance for detection of teicoplanin resistance in the S. haemolyticus strain was 82%. We stratified concordance rates first for country and then for guideline used, but observed only minor differences among countries and guidelines. Quantitative methods yielding an MIC were more concordant than non-MIC methods for penicillin resistance in the S. pneumoniae strains (94% versus 79%). The NCCLS guideline was the most frequently followed, by 61% of laboratories from 19 countries. This exercise shows that, overall, countries participating in EARSS are capable of delivering susceptibility data of good quality. The comparability of susceptibility data for penicillin resistance in S. pneumoniae and for homogeneous methicillin resistance in

  20. New developments in NASA quality assurance

    NASA Technical Reports Server (NTRS)

    Condon, John E.

    1966-01-01

    The purpose of this talk is to examine and discuss NASA's basic quality concept, the policy and procedures which define and implement this concept and subsequently explore the NASA-Industry quality relationships which are essential to the success of NASA's quality assurance concept. It is important to emphasize that NASA's Quality Assurance program is predicated on the concept of an individually tailored quality program for each significant NASA procurement - particularly, large space systems. As a result, NASA's Quality Assurance program - to be effective - must be responsive to various technologies, hardware systems, and space missions. In addition, the program must be responsive to changing policies and practices in research, engineering and procurement. Key issues in the NASA-Contractor quality relationships in the framework of an over all NASA-Industry partnership include: (1) the necessity for NASA to effectively discharge its responsibility for providing clear and complete definition of quality requirements at all phases of the procurement cycle; (2) the right of the contractor to expect an explicit definition of NASA quality requirements in each RFP and contract and to request same if it is not provided; (3) the necessity for the contractor to have a dynamic and responsive quality program which is directed towards assuring that the hardware meets all technical requirements and to accomplish this in an effective and efficient manner; and (4) the critical need for investigation and study of the economic aspects of quality and an evaluation of our policies and practices based upon the results of such a study.

  1. 7 CFR 56.39 - Quality assurance inspector required.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Quality assurance inspector required. 56.39 Section 56... Identified with Grademarks § 56.39 Quality assurance inspector required. The official identification with the... supervision of a grader or quality assurance inspector. The grader or quality assurance inspector shall...

  2. 7 CFR 56.39 - Quality assurance inspector required.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Quality assurance inspector required. 56.39 Section 56... Identified with Grademarks § 56.39 Quality assurance inspector required. The official identification with the... supervision of a grader or quality assurance inspector. The grader or quality assurance inspector shall...

  3. 7 CFR 56.39 - Quality assurance inspector required.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Quality assurance inspector required. 56.39 Section 56... Identified with Grademarks § 56.39 Quality assurance inspector required. The official identification with the... supervision of a grader or quality assurance inspector. The grader or quality assurance inspector shall...

  4. 48 CFR 37.604 - Quality assurance surveillance plans.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Quality assurance... SPECIAL CATEGORIES OF CONTRACTING SERVICE CONTRACTING Performance-Based Acquisition 37.604 Quality assurance surveillance plans. Requirements for quality assurance and quality assurance surveillance...

  5. 16 CFR 1633.6 - Quality assurance requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Quality assurance requirements. 1633.6... STANDARD FOR THE FLAMMABILITY (OPEN FLAME) OF MATTRESS SETS The Standard § 1633.6 Quality assurance requirements. (a) Quality assurance. Each manufacturer shall implement a quality assurance program to...

  6. 23 CFR 637.207 - Quality assurance program.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 23 Highways 1 2013-04-01 2013-04-01 false Quality assurance program. 637.207 Section 637.207... CONSTRUCTION INSPECTION AND APPROVAL Quality Assurance Procedures for Construction § 637.207 Quality assurance program. (a) Each STD's quality assurance program shall provide for an acceptance program and...

  7. 23 CFR 637.207 - Quality assurance program.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 23 Highways 1 2014-04-01 2014-04-01 false Quality assurance program. 637.207 Section 637.207... CONSTRUCTION INSPECTION AND APPROVAL Quality Assurance Procedures for Construction § 637.207 Quality assurance program. (a) Each STD's quality assurance program shall provide for an acceptance program and...

  8. [Quality assurance concepts in intensive care medicine].

    PubMed

    Brinkmann, A; Braun, J P; Riessen, R; Dubb, R; Kaltwasser, A; Bingold, T M

    2015-11-01

    Intensive care medicine (ICM) is characterized by a high degree of complexity and requires intense communication and collaboration on interdisciplinary and multiprofessional levels. In order to achieve good quality of care in this environment and to prevent errors, a proactive quality and error management as well as a structured quality assurance system are essential. Since the early 1990s, German intensive care societies have developed concepts for quality management and assurance in ICM. In 2006, intensive care networks were founded in different states to support the implementation of evidence-based knowledge into clinical routine and to improve medical outcome, efficacy, and efficiency in ICM. Current instruments and concepts of quality assurance in German ICM include core intensive care data from the data registry DIVI REVERSI, quality indicators, peer review in intensive care, IQM peer review, and various certification processes. The first version of German ICM quality indicators was published in 2010 by an interdisciplinary and interprofessional expert commission. Key figures, indicators, and national benchmarks are intended to describe the quality of structures, processes, and outcomes in intensive care. Many of the quality assurance tools have proved to be useful in clinical practice, but nationwide implementation still can be improved.

  9. Tool Use Within NASA Software Quality Assurance

    NASA Technical Reports Server (NTRS)

    Shigeta, Denise; Port, Dan; Nikora, Allen P.; Wilf, Joel

    2013-01-01

    As space mission software systems become larger and more complex, it is increasingly important for the software assurance effort to have the ability to effectively assess both the artifacts produced during software system development and the development process itself. Conceptually, assurance is a straightforward idea - it is the result of activities carried out by an organization independent of the software developers to better inform project management of potential technical and programmatic risks, and thus increase management's confidence in the decisions they ultimately make. In practice, effective assurance for large, complex systems often entails assessing large, complex software artifacts (e.g., requirements specifications, architectural descriptions) as well as substantial amounts of unstructured information (e.g., anomaly reports resulting from testing activities during development). In such an environment, assurance engineers can benefit greatly from appropriate tool support. In order to do so, an assurance organization will need accurate and timely information on the tool support available for various types of assurance activities. In this paper, we investigate the current use of tool support for assurance organizations within NASA, and describe on-going work at JPL for providing assurance organizations with the information about tools they need to use them effectively.

  10. ENHANCING SCIENTIFIC COLLABORATION THROUGH QUALITY ASSURANCE

    EPA Science Inventory

    The basic features of the Quality Assurance Program have been in existence since the early 1980's, but this poster will highlight some topics that have emerged more recently, in particular the Agency's laboratory competency policy, the information quality guidelines, and scientif...

  11. Quality Assurance in University Guidance Services

    ERIC Educational Resources Information Center

    Simon, Alexandra

    2014-01-01

    In Europe there is no common quality assurance framework for the delivery of guidance in higher education. Using a case study approach in four university career guidance services in England, France and Spain, this article aims to study how quality is implemented in university career guidance services in terms of strategy, standards and models,…

  12. Quality Assurance in a Children's Psychiatric Hospital.

    ERIC Educational Resources Information Center

    Baggish, Rosemary C.; And Others

    1981-01-01

    Examined the use of short-term isolation (STI) in a children's psychiatric hospital. The Joint Commission on Accreditation of Hospitals quality assurance mode was used. Studied the quality use of STI and its documentation. Data gathered served as the basis for recommendations that led to planned, informed program changes. (Author)

  13. Quality Assurance in Distance Learning Libraries

    ERIC Educational Resources Information Center

    Tripathi, Manorama; Jeevan, V. K. J.

    2009-01-01

    Purpose: The paper aims to study how the present distance learning libraries can improve upon their existing services and introduce new ones to enhance quality of services to distance learners. Design/methodology/approach: The paper includes a review of literature on quality assurance in open and distance education in general and student support…

  14. Ensuring Quality Assurance in Vocational Education

    ERIC Educational Resources Information Center

    Idialu, Ethel E.

    2013-01-01

    Vocational education emphasises skill acquisition. Quality assurance in vocational education is a concept that is concerned with high performance involving activities with vocational education such as teaching, learning, infrastructures, students' behaviour and the entire academic process. Quality vocational education refers to input and output of…

  15. The New English Quality Assurance Regime

    ERIC Educational Resources Information Center

    Brown, Roger

    2011-01-01

    England is developing a new quality assurance regime that will come into effect in October 2011. A new funding regime will operate from the following year, together with new rules to ease the participation of private higher education providers. This article describes and analyses the new quality and funding regimes. It argues that the greater…

  16. NIF Projects Controls and Information Systems Software Quality Assurance Plan

    SciTech Connect

    Fishler, B

    2011-03-18

    Quality achievement for the National Ignition Facility (NIF) and the National Ignition Campaign (NIC) is the responsibility of the NIF Projects line organization as described in the NIF and Photon Science Directorate Quality Assurance Plan (NIF QA Plan). This Software Quality Assurance Plan (SQAP) is subordinate to the NIF QA Plan and establishes quality assurance (QA) activities for the software subsystems within Controls and Information Systems (CIS). This SQAP implements an activity level software quality assurance plan for NIF Projects as required by the LLNL Institutional Software Quality Assurance Program (ISQAP). Planned QA activities help achieve, assess, and maintain appropriate quality of software developed and/or acquired for control systems, shot data systems, laser performance modeling systems, business applications, industrial control and safety systems, and information technology systems. The objective of this SQAP is to ensure that appropriate controls are developed and implemented for management planning, work execution, and quality assessment of the CIS organization's software activities. The CIS line organization places special QA emphasis on rigorous configuration control, change management, testing, and issue tracking to help achieve its quality goals.

  17. Production of test gases in the ppb range for round-robin tests and quality assurance measures during the measurement of VOCs.

    PubMed

    Moritz, Andreas; Breuer, Dietmar

    2008-12-01

    Workers exposed to volatile organic compounds (VOCs) very often suffer damage to health, and VOC odours may also represent a serious nuisance. The compounds concerned may be numerous and highly diverse; the concentrations of the individual substances however are generally relatively low. Quality assurance measures such as round-robin tests for the measurement of VOCs in indoor areas or at workplaces have not so far been available. A particular reason for this is the challenge presented by the production of test gases in the necessary concentrations. The BGIA test gas facility has therefore been modified for the production of test gases in the microg/m(3) range. A two-stage primary gas purifier, a continuous test gas generator with multi-stage dilution, a capillary evaporator for low-volatility compounds and an online thermodesorber have been installed specifically for this purpose.Purification of the primary gas proved to be particularly difficult: the available pre-purified compressed air contained organic trace impurities which fluctuated over time. The essential requirement, i.e. the injection into the test gas stream of a primary gas which was constant over time and exhibited the lowest possible contamination, could be satisfied only by catalytic decomposition of the organic residual impurities and with a supplementary adsorber unit. Even with these measures in place, small quantities of organic substances remain present, and the blank readings must still be monitored continuously. Following completion of all modifications, it proved possible to produce test gases with a high degree of reproducibility with substance concentrations in the range of 1 to 500 microg/m(3).Since 2007, the BGIA has been offering round-robin tests for VOCs with local sampling in the range from 5 to 50 microg/m(3). The first round-robin tests show that good results are obtained at concentrations from 10 to 50 microg/m(3). At the lower concentration of < 15 microg/m(3), however, the

  18. 10 CFR 63.142 - Quality assurance criteria.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... controls, processes, test equipment, tools, and skills to attain the required quality, and the need for... verifying or checking processes, it must include suitable qualifications testing of a prototype unit under... assure that tools, gages, instruments, and other measuring and testing devices used in...

  19. RTOG quality assurance guidelines for interstitial hyperthermia.

    PubMed

    Emami, B; Stauffer, P; Dewhirst, M W; Prionas, S; Ryan, T; Corry, P; Herman, T; Kapp, D S; Myerson, R J; Samulski, T

    1991-05-01

    This document specifies the current recommendations for quality assurance for hyperthermia administration with interstitial techniques as specified by the Radiation Therapy Oncology Group (RTOG). The document begins by providing a brief description of the physical principles behind the use of the three most commonly used methods of interstitial hyperthermia: radiofrequency (RF-LCF), microwave antennas, and ferromagnetic seeds. Emphasis is placed on features that effect quality assurance. Specific recommendations are provided for: a) Pretreatment planning and equipment performance checks, b) Implant considerations and documentation, c) Thermometry, and d) Safety procedures. Specific details regarding quality assurance issues that are common to all local and regional hyperthermia methods are outlined in previous documents sponsored by the RTOG. It is anticipated that technological advances may lead to future modifications of this document.

  20. 23 CFR 637.207 - Quality assurance program.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... independent assurance (IA) program consisting of the following: (1) Acceptance program. (i) Each STD's... quality control samples. (C) The quality control sampling and testing is evaluated by an IA program. (iii... appropriate. See 23 CFR 635.413(e) for specific requirements. (2) The IA program shall evaluate the...

  1. 49 CFR 179.7 - Quality assurance program.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... between managers, engineers, purchasing, construction, inspection, testing, and quality control personnel... that the fabrication and construction materials received are properly identified and documented. (5) A... 49 Transportation 3 2013-10-01 2013-10-01 false Quality assurance program. 179.7 Section...

  2. 16 CFR 1633.6 - Quality assurance requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... material or construction/assembly process used could negatively affect the test performance of the mattress... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Quality assurance requirements. 1633.6... STANDARD FOR THE FLAMMABILITY (OPEN FLAME) OF MATTRESS SETS The Standard § 1633.6 Quality...

  3. 16 CFR 1633.6 - Quality assurance requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... material or construction/assembly process used could negatively affect the test performance of the mattress... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Quality assurance requirements. 1633.6... STANDARD FOR THE FLAMMABILITY (OPEN FLAME) OF MATTRESS SETS The Standard § 1633.6 Quality...

  4. Statistical process control for radiotherapy quality assurance.

    PubMed

    Pawlicki, Todd; Whitaker, Matthew; Boyer, Arthur L

    2005-09-01

    Every quality assurance process uncovers random and systematic errors. These errors typically consist of many small random errors and a very few number of large errors that dominate the result. Quality assurance practices in radiotherapy do not adequately differentiate between these two sources of error. The ability to separate these types of errors would allow the dominant source(s) of error to be efficiently detected and addressed. In this work, statistical process control is applied to quality assurance in radiotherapy for the purpose of setting action thresholds that differentiate between random and systematic errors. The theoretical development and implementation of process behavior charts are described. We report on a pilot project is which these techniques are applied to daily output and flatness/symmetry quality assurance for a 10 MV photon beam in our department. This clinical case was followed over 52 days. As part of our investigation, we found that action thresholds set using process behavior charts were able to identify systematic changes in our daily quality assurance process. This is in contrast to action thresholds set using the standard deviation, which did not identify the same systematic changes in the process. The process behavior thresholds calculated from a subset of the data detected a 2% change in the process whereas with a standard deviation calculation, no change was detected. Medical physicists must make decisions on quality assurance data as it is acquired. Process behavior charts help decide when to take action and when to acquire more data before making a change in the process.

  5. Technical note: preventive maintenance quality assurance.

    PubMed

    Russell, D

    1992-01-01

    Performance improvements in healthcare and, specifically, in clinical engineering are required by the Joint Commission on the Accreditation of Healthcare Organizations' Plant Technology and Safety Management (PTSM) documents. The goals of healthcare service quality assurance are to establish performance requirements and improve patient outcomes. It is important that these goals be kept in the forefront of the design of clinical engineering quality assurance planning. Indicator/threshold pairs must be carefully chosen on the basis of some logical relation to the desired goals of the overall program.

  6. Quality Assurance Source Requirements Traceability Database

    SciTech Connect

    MURTHY, R., NAYDENOVA, A., DEKLEVER, R., BOONE, A.

    2006-01-30

    At the Yucca Mountain Project the Project Requirements Processing System assists in the management of relationships between regulatory and national/industry standards source criteria, and Quality Assurance Requirements and Description document (DOE/R W-0333P) requirements to create compliance matrices representing respective relationships. The matrices are submitted to the U.S. Nuclear Regulatory Commission to assist in the commission's review, interpretation, and concurrence with the Yucca Mountain Project QA program document. The tool is highly customized to meet the needs of the Office of Civilian Radioactive Waste Management Office of Quality Assurance.

  7. The HERITAGE Family Study: quality assurance and quality control.

    PubMed

    Gagnon, J; Province, M A; Bouchard, C; Leon, A S; Skinner, J S; Wilmore, J H; Rao, D C

    1996-11-01

    The HERITAGE (HEalth, RIsk factors, exercise Training And GEnetics) Family Study is the first multicenter family clinical trial of its kind. Conducted by a consortium of five universities in the United States and Canada, the study has as its primary goal to document the role of the genotype in the cardiovascular, metabolic, and hormonal responses to aerobic exercise training. A comprehensive protocol was implemented at four Clinical Centers (CC) for the generation of data on sedentary subjects. This group included 450 caucasians from 90 nuclear families (father, mother, three children) and 200 black subjects from 40 to 100 family units over a 5-year period. The entire family was tested before and after a 20-week exercise training program. The fifth participating center, the Data Coordinating Center (DCC), is responsible for data management and data analysis. A Consortium Coordinating Center (CCC) responsible for the overall coordination and direction of the study was established at the Quebec CC. Quality assurance and quality control are jointly coordinated by the CCC and the DCC. A multicenter study of this magnitude requires careful standardization of all procedures and constant monitoring of quality control at all levels of operation. This report describes the quality assurance and quality control measures implemented in the HERITAGE Family Study, including some examples with real data.

  8. The changing role of quality assurance in the pharmaceutical industry.

    PubMed

    Kieffer, Robert G

    2014-01-01

    ICH Q10. Pharmaceutical Quality System emphasizes that senior management is responsible for the quality system. Thus, it is not the quality assurance organization that has the primary responsibility for the quality system. With this shift of responsibilities, what can quality assurance do to help senior management fulfill their responsibility? How can quality assurance be more proactive, add more value? What new skills does quality assurance need to have in order to perform its new role? This article attempts to answer these questions.

  9. Quality Assurance in the Presence of Variability

    NASA Astrophysics Data System (ADS)

    Lauenroth, Kim; Metzger, Andreas; Pohl, Klaus

    Software Product Line Engineering (SPLE) is a reuse-driven development paradigm that has been applied successfully in information system engineering and other domains. Quality assurance of the reusable artifacts of the product line (e.g. requirements, design, and code artifacts) is essential for successful product line engineering. As those artifacts are reused in several products, a defect in a reusable artifact can affect several products of the product line. A central challenge for quality assurance in product line engineering is how to consider product line variability. Since the reusable artifacts contain variability, quality assurance techniques from single-system engineering cannot directly be applied to those artifacts. Therefore, different strategies and techniques have been developed for quality assurance in the presence of variability. In this chapter, we describe those strategies and discuss in more detail one of those strategies, the so called comprehensive strategy. The comprehensive strategy aims at checking the quality of all possible products of the product line and thus offers the highest benefits, since it is able to uncover defects in all possible products of the product line. However, the central challenge for applying the comprehensive strategy is the complexity that results from the product line variability and the large number of potential products of a product line. In this chapter, we present one concrete technique that we have developed to implement the comprehensive strategy that addresses this challenge. The technique is based on model checking technology and allows for a comprehensive verification of domain artifacts against temporal logic properties.

  10. 2011 SAPHIRE 8 Software Quality Assurance Status Report

    SciTech Connect

    Kurt G. Vedros

    2011-09-01

    The Software Quality Assurance engineer position was created in fiscal year 2011 to better maintain and improve the quality of the SAPHIRE 8 development program. This year's Software Quality Assurance tasks concentrated on developing the framework of the SQA program. This report reviews the accomplishments and recommendations for each of the subtasks set forth for JCN V6059: (1) Reviews, Tests, and Code Walkthroughs; (2) Data Dictionary; (3) Metrics; (4) Requirements Traceability Matrix; (5) Provide Oversight on SAPHIRE QA Activities; and (6) Support NRC Presentations and Meetings.

  11. Quality Assurance: An Educational Approach.

    ERIC Educational Resources Information Center

    Griffith, Nancy L.; Megel, Mary Erickson

    1981-01-01

    Describes a course designed to give students the theoretical and practical knowledge to understand the factors influencing the provision of quality nursing care; to use standards to evaluate nursing care; and to make planning changes to improvement. (Author)

  12. Highly Integrated Quality Assurance – An Empirical Case

    SciTech Connect

    Drake Kirkham; Amy Powell; Lucas Rich

    2011-02-01

    Highly Integrated Quality Assurance – An Empirical Case Drake Kirkham1, Amy Powell2, Lucas Rich3 1Quality Manager, Radioisotope Power Systems (RPS) Program, Idaho National Laboratory, P.O. Box 1625 M/S 6122, Idaho Falls, ID 83415-6122 2Quality Engineer, RPS Program, Idaho National Laboratory 3Quality Engineer, RPS Program, Idaho National Laboratory Contact: Voice: (208) 533-7550 Email: Drake.Kirkham@inl.gov Abstract. The Radioisotope Power Systems Program of the Idaho National Laboratory makes an empirical case for a highly integrated Quality Assurance function pertaining to the preparation, assembly, testing, storage and transportation of 238Pu fueled radioisotope thermoelectric generators. Case data represents multiple campaigns including the Pluto/New Horizons mission, the Mars Science Laboratory mission in progress, and other related projects. Traditional Quality Assurance models would attempt to reduce cost by minimizing the role of dedicated Quality Assurance personnel in favor of either functional tasking or peer-based implementations. Highly integrated Quality Assurance adds value by placing trained quality inspectors on the production floor side-by-side with nuclear facility operators to enhance team dynamics, reduce inspection wait time, and provide for immediate, independent feedback. Value is also added by maintaining dedicated Quality Engineers to provide for rapid identification and resolution of corrective action, enhanced and expedited supply chain interfaces, improved bonded storage capabilities, and technical resources for requirements management including data package development and Certificates of Inspection. A broad examination of cost-benefit indicates highly integrated Quality Assurance can reduce cost through the mitigation of risk and reducing administrative burden thereby allowing engineers to be engineers, nuclear operators to be nuclear operators, and the cross-functional team to operate more efficiently. Applicability of this case

  13. Revision 2 of the Enbridge Quality Assurance Project Plan

    EPA Pesticide Factsheets

    This Quality Assurance Project Plan (QAPP) presents Revision 2 of the organization, objectives, planned activities, and specific quality assurance/quality control (QA/QC) procedures associated with the Enbridge Marshall Pipeline Release Project.

  14. New challenges in assuring vaccine quality.

    PubMed Central

    Dellepiane, N.; Griffiths, E.; Milstien, J. B.

    2000-01-01

    In the past, quality control of vaccines depended on use of a variety of testing methods to ensure that the products were safe and potent. These methods were developed for vaccines whose safety and efficacy were based on several years worth of data. However, as vaccine production technologies have developed, so have the testing technologies. Tests are now able to detect potential hazards with a sensitivity not possible a few years ago, and an increasing array of physicochemical methods allows a much better characterization of the product. In addition to sophisticated tests, vaccine regulation entails a number of other procedures to ensure safety. These include characterization of starting materials by supplier audits, cell banking, seed lot systems, compliance with the principles of good manufacturing practices, independent release of vaccines on a lot-by-lot basis by national regulatory authorities, and enhanced pre- and post-marketing surveillance for possible adverse events following immunization. These procedures help assure vaccine efficacy and safety, and some examples are given in this article. However, some contaminants of vaccines that can be detected by newer assays raise theoretical safety concerns but their presence may be less hazardous than not giving the vaccines. Thus risk-benefit decisions must be well informed and based on scientific evidence. PMID:10743279

  15. Quality Assurance in Distance and Open Learning

    ERIC Educational Resources Information Center

    Mahafzah, Mohammed Hasan

    2012-01-01

    E-learning has become an increasingly important teaching and learning mode in educational institutions and corporate training. The evaluation of E-learning, however, is essential for the quality assurance of E-learning courses. This paper constructs a three-phase evaluation model for E-learning courses, which includes development, process, and…

  16. Quality Assurance: Enhancing or Threatening Higher Education?

    ERIC Educational Resources Information Center

    Taousanidis, Nikolaos I.; Antoniadou, Myrofora A.

    2010-01-01

    There is an increasing marketization of commodity services and, the authors argue, higher education is suffering heavily from this trend. Higher education institutions (HEIs) are currently subject to quality assurance and other externally imposed procedures that have been successfully applied in the private sector. This article analyses the…

  17. Quality Assurance in Turkish Higher Education

    ERIC Educational Resources Information Center

    Bugday Ince, Sehriban; Gounko, Tatiana

    2014-01-01

    The implementation of quality assurance (QA) is one of the most challenging reform areas for Turkey due to the unique organization of its higher education system. This paper explores the development of QA systems in Turkish universities. Using a qualitative case study approach, the authors examine how Turkey accomplishes the goal of implementing…

  18. Quality Assurance in Higher Education in Zimbabwe

    ERIC Educational Resources Information Center

    Garwe, Evelyn Chiyevo

    2014-01-01

    The purpose of this paper is to furnish local and global stakeholders with detailed information regarding the development and current status of quality assurance in the Zimbabwean higher education sector. The study used document analysis, observation and interviews with key informants as sources of data. This paper addresses the dearth of…

  19. Quality Assurance Program: Beginning Teacher Warranty.

    ERIC Educational Resources Information Center

    Barr, Robert D.

    This report discusses the Quality Assurance Program at the OSU/WOSC School of Education, a merged school serving Oregon State University and Western Oregon State College. This major reform in teacher education is designed to bring a high level of accountability to teacher education and is called a "Warranty of First-Year Teachers." If,…

  20. Software quality assurance plan for GCS

    NASA Technical Reports Server (NTRS)

    Duncan, Stephen E.; Bailey, Elizabeth K.

    1990-01-01

    The software quality assurance (SQA) function for the Guidance and Control Software (GCS) project which is part of a software error studies research program is described. The SQA plan outlines all of the procedures, controls, and audits to be carried out by the SQA organization to ensure adherence to the policies, procedures, and standards for the GCS project.

  1. SWMM 5 REDEVELOPMENT QUALITY ASSURANCE PROGRAM

    EPA Science Inventory

    EPA recently released a new version of the Storm Water Management Model (SWMM) that combines a new interface with a completely re-written computational engine. The SWMM redevelopment project proceeded under a Quality Assurance Project Plan (QAPP) that describes methods and proced...

  2. Quality Assurance Program Development--Curriculum Development.

    ERIC Educational Resources Information Center

    Wisconsin Indianhead Technical Coll., Shell Lake.

    This document has two parts: (1) course outlines and unit lesson plans for 10 vocational courses; and (2) course descriptions. competencies, and topical outlines for 7 courses in a quality assurance curriculum. In the first part, outlines and unit lesson plans are provided for the following courses: standards and specifications, materials, basic…

  3. Effectiveness of Quality Assurance Training for Youth.

    ERIC Educational Resources Information Center

    Nold, Rosie; Hanson, Dana

    2001-01-01

    A quality assurance program was designed to teach youth about safe and wholesome food production, animal management techniques, and ethical decision making related to food animal production. Participants gained skills in animal management techniques and their opinions about consumer expectations were positively influenced. The program successfully…

  4. Quality assurance and quality control in monitoring programs

    USGS Publications Warehouse

    Shampine, W.J.

    1993-01-01

    There are three general characteristics of the data to be collected in a monitoring program that should be met in order to maximize the use and value of the data: the data quality should be known the data type and quality should be consistent and comparable, and the data should be available and accessible. Potential problems with each of these characteristics are addressed effectively by quality assurance and quality control. One of the most important aspects of quality assurance in a monitoring program is the development of a quality assurance plan, which should identify clearly the quality of the data needed and describe in detail the planned actions to provide confidence that the program will meet its stated objectives. Quality control data, which allow for the quality and suitability of the environmental data to be evaluated and ascertained, should be collected and utilized as an integral part of the QA effort associated with a monitoring program.

  5. Quality Assurance through ISO 9000.

    ERIC Educational Resources Information Center

    Zuckerman, Amy

    2000-01-01

    Created in 1987 by the International Organization for Standardization, in Geneva, Switzerland, ISO 9000 is attempting to develop a world standard to help companies and other institutions measure and monitor their quality-control efforts. This article describes four school districts' successful efforts to secure ISO 9000 certification. (MLH)

  6. 222-S laboratory quality assurance plan

    SciTech Connect

    Meznarich, H.K.

    1995-04-01

    This document provides quality assurance guidelines and quality control requirements for analytical services. This document is designed on the basis of Hanford Analytical Services Quality Assurance Plan (HASQAP) technical guidelines and is used for governing 222-S and 222-SA analytical and quality control activities. The 222-S Laboratory provides analytical services to various clients including, but not limited to, waste characterization for the Tank Waste Remediation Systems (TWRS), waste characterization for regulatory waste treatment, storage, and disposal (TSD), regulatory compliance samples, radiation screening, process samples, and TPA samples. A graded approach is applied on the level of sample custody, QC, data verification, and data reporting to meet the specific needs of the client.

  7. Quality assurance in determinations of brain death.

    PubMed

    Izac, Suzette Marie

    2004-09-01

    A 2002 study (Wang et al.) revealed the need to increase quality assurance (QA) activities to improve the declaration and documentation of brain death, thus improving the opportunity and potential for organ and tissue donation. One aspect of the QA concept is to provide checklists and training to physicians and hospital staff involved. Training will ensure that all personnel are sensitive to the complex process of brain death and the many diverse issues prevalent today. Checklists may be used to exclude other conditions or causes of irreversible coma and to verify the lack of appropriate reflexes in such patients. Electroneurodiagnostic (END) technologists may be asked to perform confirmatory tests in cases of suspected brain death, such as the EEG for electrocerebral inactivity (ECI), or the brainstem auditory or somatosensory evoked potentials. A look at published Guidelines will help ensure that END technologists perform these tests correctly. A solid understanding of the process ensures that diagnostic and technical mistakes are avoided and may provide helpful guidance to all involved. This paper also includes a brief look at some other available confirmatory tests, as well as some of the ethical issues involved.

  8. SU-E-I-60: Quality Assurance Testing Methods and Customized Phantom for Magnetic Resonance Imaging and Spectroscopy

    SciTech Connect

    Song, K-H; Lee, D-W; Choe, B-Y

    2015-06-15

    Purpose: The objectives of this study are to develop an magnetic resonance imaging and spectroscopy (MRI-MRS) fused phantom along with the inserts for metabolite quantification and to conduct quantitative analysis and evaluation of the layered vials of brain-mimicking solution for quality assurance (QA) performance, according to the localization sequence. Methods: The outer cylindrical phantom body is made of acrylic materials. The section other than where the inner vials are located was filled with copper sulfate and diluted with water so as to reduce the T1 relaxation time. Sodium chloride was included to provide conductivity similar to the human body. All measurements of MRI and MRS were made using a 3.0 T scanner (Achiva Tx 3.0 T; Philips Medical Systems, Netherlands). The MRI scan parameters were as follows: (1) spin echo (SE) T1-weighted image: repetition time (TR), 500ms; echo time (TE), 20ms; matrix, 256×256; field of view (FOV), 250mm; gap, 1mm; number of signal averages (NSA), 1; (2) SE T2-weighted image: TR, 2,500 ms; TE, 80 ms; matrix, 256×256; FOV, 250mm; gap, 1mm; NSA, 1; 23 slice images were obtained with slice thickness of 5mm. The water signal of each volume of interest was suppressed by variable pulse power and optimized relaxation delays (VAPOR) applied before the scan. By applying a point-resolved spectroscopy sequence, the MRS scan parameters were as follows: voxel size, 0.8×0.8×0.8 cm{sup 3}; TR, 2,000ms; TE, 35ms; NSA, 128. Results: Using the fused phantom, the results of measuring MRI factors were: geometric distortion, <2% and ±2 mm; image intensity uniformity, 83.09±1.33%; percent-signal ghosting, 0.025±0.004; low-contrast object detectability, 27.85±0.80. In addition, the signal-to-noise ratio of N-acetyl-aspartate was consistently high (42.00±5.66). Conclusion: The MRI-MRS QA factors obtained simultaneously using the phantom can facilitate evaluation of both images and spectra, and provide guidelines for obtaining MRI and MRS QA

  9. 30 CFR 14.8 - Quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... order to assure that the finished conveyor belt will meet the flame-resistance test— (1) Flame test a sample of each batch, lot, or slab of conveyor belts; or (2) Flame test or inspect a sample of each batch or lot of the materials that contribute to the flame-resistance characteristic. (b)...

  10. Quality assurance in small plating shops

    SciTech Connect

    McNabb, W.J. )

    1993-10-01

    The potential for electroless nickel coatings in oilfield and petrochemical applications is quite high. The greatest obstacle to their use has been a reputation for poor quality due to a lack of quality control in many plating shops. To overcome this, electroless nickel shops should not only have a quality control program in their operation, but must also document its use and success. This article describes how a plating shoe can develop the necessary procedures, manuals, and paperwork trail to offer quality assurance and to satisfy customers.

  11. Quality Assurance Specifications for Planetary Protection Assays

    NASA Astrophysics Data System (ADS)

    Baker, Amy

    As the European Space Agency planetary protection (PP) activities move forward to support the ExoMars and other planetary missions, it will become necessary to increase staffing of labo-ratories that provide analyses for these programs. Standardization of procedures, a comprehen-sive quality assurance program, and unilateral training of personnel will be necessary to ensure that the planetary protection goals and schedules are met. The PP Quality Assurance/Quality Control (QAQC) program is designed to regulate and monitor procedures performed by labora-tory personnel to ensure that all work meets data quality objectives through the assembly and launch process. Because personnel time is at a premium and sampling schedules are often de-pendent on engineering schedules, it is necessary to have flexible staffing to support all sampling requirements. The most productive approach to having a competent and flexible work force is to establish well defined laboratory procedures and training programs that clearly address the needs of the program and the work force. The quality assurance specification for planetary protection assays has to ensure that labora-tories and associated personnel can demonstrate the competence to perform assays according to the applicable standard AD4. Detailed subjects included in the presentation are as follows: • field and laboratory control criteria • data reporting • personnel training requirements and certification • laboratory audit criteria. Based upon RD2 for primary and secondary validation and RD3 for data quality objectives, the QAQC will provide traceable quality assurance safeguards by providing structured laboratory requirements for guidelines and oversight including training and technical updates, standardized documentation, standardized QA/QC checks, data review and data archiving.

  12. Quality Assurance and School Monitoring in Hong Kong

    ERIC Educational Resources Information Center

    Mok, Magdalena Mo Ching

    2007-01-01

    This study reports on the Hong Kong education quality assurance and school monitoring system. Three research questions were addressed: (1) Who controls the quality of school education in Hong Kong? (2) What strategies are used in the Hong Kong school education quality assurance process? (3) Agenda for Future Research on quality assurance and…

  13. 10 CFR 830.121 - Quality Assurance Program (QAP).

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Quality Assurance Program (QAP). 830.121 Section 830.121 Energy DEPARTMENT OF ENERGY NUCLEAR SAFETY MANAGEMENT Quality Assurance Requirements § 830.121 Quality... the Quality Assurance criteria in § 830.122. (b) The contractor responsible for a DOE nuclear...

  14. 10 CFR 830.121 - Quality Assurance Program (QAP).

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 4 2013-01-01 2013-01-01 false Quality Assurance Program (QAP). 830.121 Section 830.121 Energy DEPARTMENT OF ENERGY NUCLEAR SAFETY MANAGEMENT Quality Assurance Requirements § 830.121 Quality... the Quality Assurance criteria in § 830.122. (b) The contractor responsible for a DOE nuclear...

  15. 10 CFR 72.140 - Quality assurance requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Quality assurance requirements. 72.140 Section 72.140... SPENT NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE Quality Assurance § 72.140 Quality assurance requirements. (a) Purpose. This subpart describes quality...

  16. 10 CFR 830.122 - Quality assurance criteria.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 4 2014-01-01 2014-01-01 false Quality assurance criteria. 830.122 Section 830.122 Energy DEPARTMENT OF ENERGY NUCLEAR SAFETY MANAGEMENT Quality Assurance Requirements § 830.122 Quality assurance...) Criterion 3—Management/Quality Improvement. (1) Establish and implement processes to detect and...

  17. 10 CFR 830.122 - Quality assurance criteria.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Quality assurance criteria. 830.122 Section 830.122 Energy DEPARTMENT OF ENERGY NUCLEAR SAFETY MANAGEMENT Quality Assurance Requirements § 830.122 Quality assurance...) Criterion 3—Management/Quality Improvement. (1) Establish and implement processes to detect and...

  18. Advanced Quality Assurance for CNAO

    NASA Astrophysics Data System (ADS)

    Amaldi, U.; Hajdas, W.; Iliescu, S.; Malakhov, N.; Samarati, J.; Sauli, F.; Watts, D.

    2010-05-01

    We describe the test results of a Proton Range Radiography system, designed to provide in-beam integrated density images of the patients before treatment at hadrontherapy centers. The instrument includes a set of position-sensitive detectors and a scintillator stack read out with solid-state sensors to record the Bragg energy loss profile for each track.

  19. ALMA quality assurance: concepts, procedures, and tools

    NASA Astrophysics Data System (ADS)

    Chavan, A. M.; Tanne, S. L.; Akiyama, E.; Kurowski, R.; Randall, S.; Vila Vilaro, B.; Villard, E.

    2016-07-01

    Data produced by ALMA for the community undergoes a rigorous quality assurance (QA) process, from the initial observation ("QA0") to the final science-ready data products ("QA2"), to the QA feedback given by the Principal Investigators (PIs) when they receive the data products ("QA3"). Calibration data is analyzed to measure the performance of the observatory and predict the trend of its evolution ("QA1"). The procedure develops over different steps and involves several actors across all ALMA locations; it is made possible by the support given by dedicated software tools and a complex database of science data, meta-data and operational parameters. The life-cycle of each involved entity is well-defined, and it prevents for instance that "bad" data (that is, data not meeting the minimum quality standards) is ever processed by the ALMA pipeline. This paper describes ALMA's quality assurance concepts and procedures, including the main enabling software components.

  20. [Quality assurance in occupational health services].

    PubMed

    Michalak, J

    1996-01-01

    The general conditions influencing the quality assurance and audit in Polish occupational health services are presented. The factors promoting or hampering the implementation of quality assurance and audits are also discussed. The major influence on the transformation of Polish occupational health services in exorted by employers who are committed to cover the costs of the obligatory prophylactic examination of their employees. This is the factor which also contributes to the improvement of quality if services. The definitions of the most important terms are reviewed to highlight their accordance with the needs of occupational health services in Poland. The examples of audit are presented and the elements of selected methods of auditing are suggested to be adopted in Poland.

  1. The use of mystery shopping for quality assurance evaluations of HIV/STI testing sites offering services to young gay and bisexual men.

    PubMed

    Bauermeister, José A; Pingel, Emily S; Jadwin-Cakmak, Laura; Meanley, Steven; Alapati, Deepak; Moore, Michael; Lowther, Matthew; Wade, Ryan; Harper, Gary W

    2015-10-01

    Young men who have sex with men (YMSM) are at increased risk for HIV and STI infection. While encouraging HIV and STI testing among YMSM remains a public health priority, we know little about the cultural competency of providers offering HIV/STI tests to YMSM in public clinics. As part of a larger intervention study, we employed a mystery shopper methodology to evaluate the LGBT cultural competency and quality of services offered in HIV and STI testing sites in Southeast Michigan (n = 43).We trained and deployed mystery shoppers (n = 5) to evaluate the HIV and STI testing sites by undergoing routine HIV/STI testing. Two shoppers visited each site, recording their experiences using a checklist that assessed 13 domains, including the clinic's structural characteristics and interactions with testing providers. We used the site scores to examine the checklist's psychometric properties and tested whether site evaluations differed between sites only offering HIV testing (n = 14) versus those offering comprehensive HIV/STI testing (n = 29). On average, site scores were positive across domains. In bivariate comparisons by type of testing site, HIV testing sites were more likely than comprehensive HIV/STI testing clinics to ascertain experiences of intimate partner violence, offer action steps to achieve safer sex goals, and provide safer sex education. The developed checklist may be used as a quality assurance indicator to measure HIV/STI testing sites' performance when working with YMSM. Our findings also underscore the need to bolster providers' provision of safer sex education and behavioral counseling within comprehensive HIV/STI testing sites.

  2. The Use of Mystery Shopping for Quality Assurance Evaluations of HIV/STI Testing Sites Offering Services to Young Gay and Bisexual Men

    PubMed Central

    Bauermeister, José A.; Pingel, Emily S.; Jadwin-Cakmak, Laura; Meanley, Steven; Alapati, Deepak; Moore, Michael; Lowther, Matthew; Wade, Ryan; Harper, Gary W.

    2015-01-01

    Young men who have sex with men (YMSM) are at increased risk for HIV and STI infection. While encouraging HIV and STI testing among YMSM remains a public health priority, we know little about the cultural competency of providers offering HIV/STI tests to YMSM in public clinics. As part of a larger intervention study, we employed a mystery shopper methodology to evaluate the LGBT cultural competency and quality of services offered in HIV and STI testing sites in Southeast Michigan (n = 43).We trained and deployed mystery shoppers (n = 5) to evaluate the HIV and STI testing sites by undergoing routine HIV/STI testing. Two shoppers visited each site, recording their experiences using a checklist that assessed 13 domains, including the clinic’s structural characteristics and interactions with testing providers. We used the site scores to examine the checklist’s psychometric properties and tested whether site evaluations differed between sites only offering HIV testing (n = 14) versus those offering comprehensive HIV/STI testing (n = 29). On average, site scores were positive across domains. In bivariate comparisons by type of testing site, HIV testing sites were more likely than comprehensive HIV/STI testing clinics to ascertain experiences of intimate partner violence, offer action steps to achieve safer sex goals, and provide safer sex education. The developed checklist may be used as a quality assurance indicator to measure HIV/STI testing sites’ performance when working with YMSM. Our findings also underscore the need to bolster providers’ provision of safer sex education and behavioral counseling within comprehensive HIV/STI testing sites. PMID:26303197

  3. The NOνA Module Factory Quality Assurance System

    NASA Astrophysics Data System (ADS)

    Smith, Alex; the NOνA Collaboration

    The NOνA experiment will measure neutrino oscillations using a long-baseline beam, a ∼220-ton near detector and a ∼14-kiloton far detector. Production of ∼12500 modules to build these detectors is an industrial scale operation requiring careful quality assurance to meet the stringent technical specifications. Unlike a typical industrial operation, this project will use primarily a part time labor force of ∼200 University of Minnesota undergraduate students managed by a small team of full time employees. The quality assurance system is involved in nearly every aspect of the production: assembly, scheduling, training, payroll, materials, machine maintenance, test data, and safety compliance. The quality assurance data collected during the assembly process allows us to quickly identify and correct any problems that arise.

  4. Software for Optimizing Quality Assurance of Other Software

    NASA Technical Reports Server (NTRS)

    Feather, Martin; Cornford, Steven; Menzies, Tim

    2004-01-01

    Software assurance is the planned and systematic set of activities that ensures that software processes and products conform to requirements, standards, and procedures. Examples of such activities are the following: code inspections, unit tests, design reviews, performance analyses, construction of traceability matrices, etc. In practice, software development projects have only limited resources (e.g., schedule, budget, and availability of personnel) to cover the entire development effort, of which assurance is but a part. Projects must therefore select judiciously from among the possible assurance activities. At its heart, this can be viewed as an optimization problem; namely, to determine the allocation of limited resources (time, money, and personnel) to minimize risk or, alternatively, to minimize the resources needed to reduce risk to an acceptable level. The end result of the work reported here is a means to optimize quality-assurance processes used in developing software.

  5. Quality assurance of PMR-15

    NASA Technical Reports Server (NTRS)

    Hunter, A. B.

    1979-01-01

    Controls on the PMR-15 resin and/or prepreg were established to ensure a solid base for the subsequent process development task. The effort was divided into subtasks which included evaluation of commercially available graphite/PMR-15 polyimide prepregs, detailed evaluation of materials and selection of chemical test procedures. During the initial phase of the program a variability problem was detected in the PMR-15 resin. The manufacturing and/or storage of the PMR-15 resin/esters was identified as the chief cause for the variability.

  6. 7 CFR 56.39 - Quality assurance inspector required.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... supervision of a grader or quality assurance inspector. The grader or quality assurance inspector shall have.... 14, 1977. Redesignated at 42 FR 32514, June 27, 1977, as amended at 46 FR 39570, Aug. 4,...

  7. 7 CFR 56.39 - Quality assurance inspector required.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... supervision of a grader or quality assurance inspector. The grader or quality assurance inspector shall have.... 14, 1977. Redesignated at 42 FR 32514, June 27, 1977, as amended at 46 FR 39570, Aug. 4,...

  8. Now & Then: Ingrid Proctor-Fridia: Quality Assurance Representative.

    ERIC Educational Resources Information Center

    Barnes, Sue; Michalowicz, Karen Dee

    1995-01-01

    Describes the use of geometry now by a U.S. Department of Defense quality assurance representative and in ancient times by the Egyptians and Babylonians. Includes reproducible student worksheets on quality assurance. (MKR)

  9. 78 FR 7816 - Quality Assurance Program Requirements (Operations)

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-04

    ... COMMISSION Quality Assurance Program Requirements (Operations) AGENCY: Nuclear Regulatory Commission. ACTION... issuing for public comment draft regulatory guide (DG), DG-1300, ``Quality Assurance Program Requirements...'s Agencywide Documents Access and Management System (ADAMS): You may access...

  10. Quality Assurance of Quality Assurance Agencies from an Asian Perspective: Regulation, Autonomy and Accountability

    ERIC Educational Resources Information Center

    Hou, Angela Yung-Chi; Ince, Martin; Tsai, Sandy; Chiang, Chung Lin

    2015-01-01

    As quality guardians of higher education, quality assurance agencies are required to guarantee the credibility of the review process and to ensure the objectivity and transparency of their decisions and recommendations. These agencies are therefore expected to use a range of internal and external approaches to prove the quality of their review…

  11. 10 CFR 63.142 - Quality assurance criteria.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... and data; tests and experiments; scientific studies; facility and equipment design and construction... description of the quality assurance program to be applied to all structures, systems, and components... include structures, systems, and components that prevent or mitigate the consequences of postulated...

  12. 10 CFR 63.142 - Quality assurance criteria.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... and data; tests and experiments; scientific studies; facility and equipment design and construction... description of the quality assurance program to be applied to all structures, systems, and components... include structures, systems, and components that prevent or mitigate the consequences of postulated...

  13. Quality Assurance and Quality Enhancement in Higher Education: Contested Territories?

    ERIC Educational Resources Information Center

    Filippakou, Ourania; Tapper, Ted

    2008-01-01

    This paper analyses the unfolding of the quality agenda in England from 1992 to the present. By using two disciplinary approaches, "political science" and "social philosophy", the article traces the recent transition from quality assurance to quality enhancement. How is this development to be explained and how significant is…

  14. Total quality assurance and peer education.

    PubMed

    Croll, N; Jurs, E; Kennedy, S

    1993-05-01

    To promote program quality assurance, the Office of Health Promotion and Education at Penn State University evaluated peer health educators' presentation skills. Professional staff and experienced peer educators used an instrument tested for interobserver reliability to evaluate effectiveness in three skill areas: knowledge, delivery, and sensitivity. Each skill was rated, using a 4-point Likert-type scale. Knowledge included measures of preparation, subject knowledge, and ability to respond to questions knowledgeably; delivery included measures of clarity of directions, pacing, and transitions, appropriate and challenging questions, cooperation with co-facilitators, and enthusiasm; and sensitivity included comfort level, establishing trust in the group, nonjudgmentalism, appropriate use of humor, and nonsexist/nonheterosexist language. The evaluation teams observed and reviewed 18 work-shops conducted by 24 peer educators. Of the 24 educators evaluated, only 4 scored below 85%, the threshold for acceptable performance, and most scored above 90% in competency. Once baseline data had been gathered, the professional staff established a requirement that peer educators who did not meet this threshold must conduct their next two presentations with experienced peer educators who had met or exceeded it, and that professional staff members should work with students individually to improve skill levels. Evaluation criteria and threshold rates are to be reviewed each year.

  15. 10 CFR 72.174 - Quality assurance records.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Quality assurance records. 72.174 Section 72.174 Energy... NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE Quality Assurance § 72.174 Quality assurance records. The licensee, applicant for a license, certificate holder,...

  16. 10 CFR 71.135 - Quality assurance records.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Quality assurance records. 71.135 Section 71.135 Energy... Assurance § 71.135 Quality assurance records. The licensee, certificate holder, and applicant for a CoC... include the instructions, procedures, and drawings required by § 71.111 to prescribe quality...

  17. 42 CFR 417.418 - Qualifying condition: Quality assurance program.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 3 2010-10-01 2010-10-01 false Qualifying condition: Quality assurance program... Qualifying condition: Quality assurance program. (a) Condition. The HMO or CMP must make arrangements for a quality assurance program that meets the requirements of this section. (b) Standard. An HMO or CMP...

  18. 38 CFR 46.6 - Medical quality assurance records confidentiality.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Medical quality assurance records confidentiality. 46.6 Section 46.6 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS... Medical quality assurance records confidentiality. Note that medical quality assurance records that...

  19. Quality Assurance of Assessment and Moderation Discourses Involving Sessional Staff

    ERIC Educational Resources Information Center

    Grainger, Peter; Adie, Lenore; Weir, Katie

    2016-01-01

    Quality assurance is a major agenda in tertiary education. The casualisation of academic work, especially in teaching, is also a quality assurance issue. Casual or sessional staff members teach and assess more than 50% of all university courses in Australia, and yet the research in relation to the role sessional staff play in quality assurance of…

  20. 10 CFR 63.144 - Quality assurance program change.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Quality assurance program change. 63.144 Section 63.144 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Quality Assurance § 63.144 Quality assurance program change. Changes...

  1. 10 CFR 63.144 - Quality assurance program change.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Quality assurance program change. 63.144 Section 63.144 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Quality Assurance § 63.144 Quality assurance program change. Changes...

  2. 10 CFR 63.144 - Quality assurance program change.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Quality assurance program change. 63.144 Section 63.144 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Quality Assurance § 63.144 Quality assurance program change. Changes...

  3. 10 CFR 63.144 - Quality assurance program change.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Quality assurance program change. 63.144 Section 63.144 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Quality Assurance § 63.144 Quality assurance program change. Changes...

  4. 10 CFR 63.144 - Quality assurance program change.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Quality assurance program change. 63.144 Section 63.144 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Quality Assurance § 63.144 Quality assurance program change. Changes...

  5. 49 CFR 180.505 - Quality assurance program.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Quality assurance program. 180.505 Section 180.505... MAINTENANCE OF PACKAGINGS Qualification and Maintenance of Tank Cars § 180.505 Quality assurance program. The quality assurance program requirements of § 179.7 of this subchapter apply....

  6. 48 CFR 2152.246-70 - Quality assurance requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false Quality assurance... PRECONTRACT PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 2152.246-70 Quality assurance requirements. As prescribed by 2146.270-1 insert the following clause: Quality Assurance Requirements (OCT...

  7. 49 CFR 180.505 - Quality assurance program.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Quality assurance program. 180.505 Section 180.505 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... Qualification and Maintenance of Tank Cars § 180.505 Quality assurance program. The quality assurance...

  8. 49 CFR 180.505 - Quality assurance program.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Quality assurance program. 180.505 Section 180.505 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... Qualification and Maintenance of Tank Cars § 180.505 Quality assurance program. The quality assurance...

  9. Perspectives on Quality Assurance in Higher Education in Norway

    ERIC Educational Resources Information Center

    Lycke, Kirsten Hofgaard

    2004-01-01

    Quality assurance is well known internationally but the notion is relatively new in Norway. To understand some of the issues and dilemmas that emerge in the Norwegian reception of quality assurance in higher education, this article traces how quality assurance is gaining its form and how international trends are understood, transposed and adopted…

  10. Development of an Instructional Quality Assurance Model in Nursing Science

    ERIC Educational Resources Information Center

    Ajpru, Haruthai; Pasiphol, Shotiga; Wongwanich, Suwimon

    2011-01-01

    The purpose of this study was to develop an instructional quality assurance model in nursing science. The study was divided into 3 phases; (1) to study the information for instructional quality assurance model development (2) to develop an instructional quality assurance model in nursing science and (3) to audit and the assessment of the developed…

  11. Quality Assurance in Higher Education: Proposals for Consultation.

    ERIC Educational Resources Information Center

    Higher Education Funding Council for England, Bristol.

    This document sets out for consultation proposals for a revised method for quality assurance of teaching and learning in higher education. The proposals cover: (1) the objectives and principles of quality assurance; (2) an approach to quality assurance based on external audit principles; (3) the collection and publication of information; (4)…

  12. Single-Subject Evaluation: A Tool for Quality Assurance.

    ERIC Educational Resources Information Center

    Nuehring, Elane M.; Pascone, Anne B.

    1986-01-01

    The use of single-subject designs in peer review, in utilization review, and in other quality-assurance audits is encouraged. Presents an overview of the methodologies of single-subject designs and quality assurance, and provides examples of cases in which single-subject techniques furnished relevant quality assurance documentation. (Author/ABB)

  13. Operational excellence (six sigma) philosophy: Application to software quality assurance

    SciTech Connect

    Lackner, M.

    1997-11-01

    This report contains viewgraphs on operational excellence philosophy of six sigma applied to software quality assurance. This report outlines the following: goal of six sigma; six sigma tools; manufacturing vs administrative processes; Software quality assurance document inspections; map software quality assurance requirements document; failure mode effects analysis for requirements document; measuring the right response variables; and questions.

  14. 10 CFR 74.59 - Quality assurance and accounting requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... NUCLEAR MATERIAL Formula Quantities of Strategic Special Nuclear Material § 74.59 Quality assurance and... licensee shall assure that the quality of SSNM measurement systems and material processing practices is... 10 Energy 2 2011-01-01 2011-01-01 false Quality assurance and accounting requirements....

  15. Quality Assurance in Postgraduate Education. ENQA Workshop Report 12

    ERIC Educational Resources Information Center

    Bitusikova, Alexandra; Bohrer, Janet; Borosic, Ivana; Costes, Nathalie; Edinsel, Kerim; Hollander, Karoline; Jacobsson, Gunilla; Jakopovic, Ivan Filip; Kearney, Mary-Louise; Mulder, Fred; Negyesi, Judith; Pietzonka, Manuel

    2010-01-01

    The present report follows an ENQA (European Association for Quality Assurance in Higher Education) Workshop on Quality Assurance and Postgraduate Education, hosted by the Romanian Agency for Quality Assurance in Higher Education (ARACIS) in Brasov, Romania on 12-13 March 2009. The workshop was an excellent opportunity for ENQA members to exchange…

  16. Quality Assurance in Transnational Higher Education. ENQA Workshop Report 11

    ERIC Educational Resources Information Center

    Bennett, Paul; Bergan, Sjur; Cassar, Daniela; Hamilton, Marlene; Soinila, Michele; Sursock, Andree; Uvalic-Trumbic, Stamenka; Williams, Peter

    2010-01-01

    The present report is the product of an ENQA (European Association for Quality Assurance in Higher Education) Bologna Seminar "Quality Assurance in Transnational Education: from words to action" hosted by the Quality Assurance Agency (QAA, UK) in London in December, 2008. The seminar discussed the current trends in Transnational…

  17. 40 CFR 264.19 - Construction quality assurance program.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Construction quality assurance program... FACILITIES General Facility Standards § 264.19 Construction quality assurance program. (a) CQA program. (1) A construction quality assurance (CQA) program is required for all surface impoundment, waste pile, and...

  18. 40 CFR 265.19 - Construction quality assurance program.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Construction quality assurance program..., STORAGE, AND DISPOSAL FACILITIES General Facility Standards § 265.19 Construction quality assurance program. (a) CQA program. (1) A construction quality assurance (CQA) program is required for all...

  19. Quality assurance program plan for radionuclide airborne emissions monitoring

    SciTech Connect

    Boom, R.J.

    1995-12-01

    This Quality Assurance Program Plan identifies quality assurance program requirements and addresses the various Westinghouse Hanford Company organizations and their particular responsibilities in regards to sample and data handling of radiological airborne emissions. This Quality Assurance Program Plan is prepared in accordance with and to written requirements.

  20. Quality Assurance/Quality Control Jobs

    NASA Astrophysics Data System (ADS)

    Fanslau, Melody; Young, Janelle

    The production of a quality and safe food product is essential to the success of any food manufacturing facility. Because of this great importance, a career in quality can be extremely rewarding. Without happy customers willing to buy a product, a company would not be able to survive. Quality issues such as foreign objects, spoiled or mislabeled product, failure to meet net weight requirements, or a recall can all turn customers away from buying a product. The food industry is a customer-driven market in which some consumers are brand loyal based on a history of high quality or in which a single bad experience with a product will turn them away for a lifetime. With this said, the main role of a quality department is to help ensure that quality issues such as these are eliminated or kept to a minimum to maintain or increase the number of customers purchasing their product.

  1. Management of government quality assurance functions for NASA contracts

    NASA Technical Reports Server (NTRS)

    1993-01-01

    This handbook sets forth requirements for NASA direction and management of government quality assurance functions performed for NASA contracts and is applicable to all NASA installations. These requirements will standardize management to provide the minimum oversight and effective use of resources. This handbook implements Federal Acquisition Regulation (FAR) Part 46, NASA FAR Supplement 18-46, Quality Assurance, and NMI 7410.1. Achievement of established quality and reliability goals at all levels is essential to the success of NASA programs. Active participation by NASA and other agency quality assurance personnel in all phases of contract operations, including precontract activity, will assist in the economic and timely achievement of program results. This involves broad participation in design, development, procurement, inspection, testing, and preventive and corrective actions. Consequently, government, as well as industry, must place strong emphasis on the accomplishment of all functions having a significant bearing on quality and reliability from program initiation through end-use of supplies and services produced. For purposes of implementing NASA and other agency agreements, and to provide for uniformity and consistency, the terminology and definitions prescribed herein and in a future handbook shall be utilized for all NASA quality assurance delegations and subsequent redelegations.

  2. The quality assurance program at K & S

    SciTech Connect

    Slowey, T.W.

    1993-12-31

    K & S operates the largest and one of the most comprehensive Accredited Dosimetry Calibration Laboratories (ADCLs) in the American Association of Physicists in Medicine (AAPM) secondary laboratory system. It offers calibrations covering energies from Grenz-Ray (0.03-mm Al) to cesium-137 and cobalt-60, brachytherapy source and well chamber calibrations for low-activity sources, and, recently, high-dose-rate iridium-192. The present Quality Assurance (QA) program at K & S began with the AAPM Guidelines for Accreditation (Task Group No. 22 and No. 3, 1989) and grew over the past 10 years to include all aspects of providing a private, self-supporting calibration service from a free-standing independent facility. Some aspects of the QA program were prompted by the requirements of the nuclear power industry while other parts were from national consensus standards or the experiences of staff. Redundancy and teamwork are the most important characteristics of this QA program. K & S has participated in a National Institute of Standards and Technology (NIST) measurement quality assurance (MQA) program since 1982, and, in recent years, an ADCL intralaboratory intercomparison was conducted by Task Group 3 of the Radiation Therapy Committee of the AAPM. One measure of the credibility of a QA program is consistent performance on the MQA program and the ADCL intercomparisons over the past 10 years. An equally important measure of the ability of a program to assure quality results is the frequency of reported errors.

  3. Collagen solubility testing, a quality assurance step for reproducible electro-spun nano-fibre fabrication. A technical note.

    PubMed

    Zeugolis, D I; Li, B; Lareu, R R; Chan, C K; Raghunath, M

    2008-01-01

    Collagen is the main component of the extra-cellular matrix and has been utilised for numerous clinical applications in many forms and products. However, since collagen remains a natural animal-derived biopolymer, variation between batches should be addressed and minimised to ensure reproducibility of the fabrication process. Recently, electro-spinning of collagen has been introduced as a leading technique for the production of bio-mimetic nano-scale scaffolds for tissue-engineering applications. However, no protocols are available that would allow comparisons of the quality of different collagen raw materials prior to the electro-spinning process. In order to bridge this gap we assessed the solubility of various freeze-dried collagens in 0.5 M acetic acid and analysed the solved collagen by gel electrophoresis. We show that raw material of limited solubility in acetic acid will not render high quality electro-spun nano-fibres using hexafluoropropanol. In particular, insoluble collagen directly failed to produce nano-fibres, collagen of reduced solubility produced fused nano-fibres with limited inter-nano-fibre space, whilst purified type-I collagen of high solubility produced smooth, reproducible nano-fibres. Gel electrophoresis confirmed the amount of solubility, as well as qualitative differences in terms of collagen cross-links and collagen types. We recommend this simple and fast step to save costs and to enhance control over the electro-spinning process of collagen. Furthermore, we believe that the solubility test should be introduced prior to any collagenous matrix preparation in order to ensure reproducibility and accuracy.

  4. Apollo experience report: Reliability and quality assurance

    NASA Technical Reports Server (NTRS)

    Sperber, K. P.

    1973-01-01

    The reliability of the Apollo spacecraft resulted from the application of proven reliability and quality techniques and from sound management, engineering, and manufacturing practices. Continual assessment of these techniques and practices was made during the program, and, when deficiencies were detected, adjustments were made and the deficiencies were effectively corrected. The most significant practices, deficiencies, adjustments, and experiences during the Apollo Program are described in this report. These experiences can be helpful in establishing an effective base on which to structure an efficient reliability and quality assurance effort for future space-flight programs.

  5. Quality assurance reviews: how they differ from peer reviews.

    PubMed

    Adams, N H

    1998-01-01

    Research papers and reports written by scientists and engineers in the United States Environmental Protection Agency are reviewed by the agency's quality assurance staff. EPA papers and reports are subjected to peer reviews that check for the validity of conclusions and the general agreement with the body of technical knowledge in the subject area. Quality assurance reviews differ from peer reviews in that the focus of the quality assurance review is on the following criteria: Consistency: Were reasonable and consistent units of measurement and generally acceptable formulas used throughout? Are the appropriate number of significant figures reported? Correctness: Were matrix-compatible methods used? Were measurements within the working range of the method? Can measurements be traced to a recognized standard or source (e.g., the National Institute of Standards and Technology)? Can calculations be verified, starting from representative raw data and proceeding to the summary data presented in the paper or report? Coherence: Do the stated conclusions follow from the data presented? Are the assumptions clearly stated? Are inconsistencies between data and conclusions discussed? Clarity: Are special terms and acronyms defined? Can a person with a general technical background in the subject understand the paper or report? Conformance: Did the study follow the test/quality assurance plan, with appropriate calibrations and other quality-control checks, audits, and data validations? If not, is there a discussion of problems? Concordance: Were data quality objectives met? Were the data quality indicator goals achieved for precision, accuracy, representativeness, comparability, and completeness? The importance of these quality assurance review criteria are discussed along with examples from current work.

  6. Software Quality Assurance: Early and Continuous Throughout the Lifecycle

    DTIC Science & Technology

    2009-04-23

    Assessment ( ISQA ) • Wrap-up • Glossary 2SSTC 2009 – SW Qual Assurance in Lifecycle (20-Apr-2009).ppt Perspectives Influence Software Quality Goals...yc e • Independent Software Quality Assessment ( ISQA ) • Wrap-up • Glossary 5SSTC 2009 – SW Qual Assurance in Lifecycle (20-Apr-2009).ppt Why Software... ISQA ) • Wrap-up • Glossary 7SSTC 2009 – SW Qual Assurance in Lifecycle (20-Apr-2009).ppt Software Quality Assurance Problem, Solution, Result Problem

  7. An assessment of African test sites in the context of a global network of quality-assured reference standards

    USGS Publications Warehouse

    Chander, G.; Xiong, X.; Angal, A.; Choi, T.

    2009-01-01

    The Committee on Earth Observation Satellites (CEOS) Infrared and Visible Optical Sensors (IVOS) subgroup members established a set of CEOS-endorsed globally distributed reference standard test sites for the postlaunch calibration of space-based optical imaging sensors. This paper discusses the top five African pseudo-invariant sites (Libya 4, Mauritania 1/2, Algeria 3, Libya 1, and Algeria 5) that were identified by the IVOS subgroup. This paper focuses on monitoring the long-term radiometric stability of the Terra Moderate Resolution Imaging Spectroradiometer (MODIS) and the Landsat 7 (L7) Enhanced Thematic Mapper Plus (ETM+) sensors using near-simultaneous and cloud-free image pairs acquired from launch to December 2008 over the five African desert sites. Residual errors and coefficients of determination were also generated to support the quality assessment of the calibration differences between the two sensors. An effort was also made to evaluate the relative stability of these sites for long-term monitoring of the optical sensors. ??2009 IEEE.

  8. Online Course Quality Assurance: Development of a Quality Checklist

    ERIC Educational Resources Information Center

    McGahan, Steven J.; Jackson, Christina M.; Premer, Karen

    2015-01-01

    The University of Nebraska at Kearney's Online Course Checklist is the main instrument for assessing the quality of online courses at UNK. A number of issues were faced when developing and deploying this quality assurance checklist at a small four-year university. The process including development, implementation, and revision is discussed along…

  9. QUALITY SCIENCE AND QUALITY ASSURANCE: OBSERVATIONS OR AN ENVIRONMENTAL SCIENTIST

    EPA Science Inventory

    --

    ABSTRACT
    The purpose of this manuscript is to examine the relationship between quality science (QS) and quality assurance (QA). Many research scientists definitely want to do QS, but are afraid or do not want to do QA because they are intimidated by the QA proc...

  10. Predicting Software Assurance Using Quality and Reliability Measures

    DTIC Science & Technology

    2014-12-01

    found during development by testing and other methods . Based on an analysis of pump recalls and adverse events, the FDA concluded that many of the...Overview ix Abstract xiii 1 Introduction 1 2 Assurance 3 2.1 DoD Assurance Case Example 4 3 Analysis of Quality Cases 7 3.1 SEI Data 7 3.2 Defect...Prediction Models 8 3.3 In-Depth Analysis : Security Focused Example (Project A1) 11 3.3.1 Security Example Results 11 3.3.2 Security Example

  11. Quality assurance and reliability sub-committee W88-0/Mk5 weapon assessment NSA lab test results (u)

    SciTech Connect

    Whitney, Earl M

    2010-11-29

    The purpose of this report is to gather appropriate level of relevant stockpile surveillance data to assess trends in the NEP quality, reliability, performance, and safety over the life of the system. The objectives are to gather relevant stockpile data to assess NEP quality and trends and to develop metrics to assess the suitability of the surveillance sampling regime to meet assessment process requirements.

  12. 48 CFR 846.408 - Single-agency assignments of Government contract quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... of Government contract quality assurance. 846.408 Section 846.408 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality Assurance 846.408 Single-agency assignments of Government contract quality assurance....

  13. 48 CFR 46.408 - Single-agency assignments of Government contract quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... of Government contract quality assurance. 46.408 Section 46.408 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality Assurance 46.408 Single-agency assignments of Government contract quality assurance. (a)...

  14. 10 CFR 71.135 - Quality assurance records.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Assurance § 71.135 Quality assurance records. The licensee, certificate holder, and applicant for a CoC..., location, and assigned responsibility. The licensee, certificate holder, and applicant for a CoC shall... a CoC last engage in the activity for which the quality assurance program was developed. If...

  15. Measurement quality assurance for radioassay laboratories

    SciTech Connect

    McCurdy, D.E.

    1993-12-31

    Until recently, the quality of U.S. radioassay laboratory services has been evaluated by a limited number of governmental measurement assurance programs (MAPs). The major programs have been limited to the U.S. Department of Energy (DOE), the U.S. Environmental Protection Agency (EPA) and the U.S. Nuclear Regulatory Commission (NRC). In 1988, an industry MAP was established for the nuclear power utility industry through the U.S. Council for Energy Awareness/National Institute of Standards and Technology (USCEA/NIST). This program functions as both a MAP for utility laboratories and/or their commercial contractor laboratories, and as a traceability program for the U.S. radioactive source manufacturers and the utility laboratories. Each of these generic MAPs has been initiated and is maintained to serve the specific needs of the sponsoring agency or organization. As a result, there is diversification in their approach, scope, requirements, and degree of traceability to NIST. In 1987, a writing committee was formed under the American National Standards Institute (ANSI) N42.2 committee to develop a standard to serve as the basis document for the creation of a national measurement quality assurance (MQA) program for radioassay laboratories in the U.S. The standard is entitled, {open_quotes}Measurement Quality Assurance For Radioassay Laboratories.{open_quotes} The document was developed to serve as a guide for MQA programs maintained for the specialized sectors of the radioassay community, such as bioassay, routine environmental monitoring, environmental restoration and waste management, radiopharmaceuticals, and nuclear facilities. It was the intent of the writing committee to develop a guidance document that could be utilized to establish a laboratory`s specific data quality objectives (DQOs) that govern the operational requirements of the radioassay process, including mandated protocols and recommendations.

  16. [Quality assurance and quality management in intensive care].

    PubMed

    Notz, K; Dubb, R; Kaltwasser, A; Hermes, C; Pfeffer, S

    2015-11-01

    Treatment success in hospitals, particularly in intensive care units, is directly tied to quality of structure, process, and outcomes. Technological and medical advancements lead to ever more complex treatment situations with highly specialized tasks in intensive care nursing. Quality criteria that can be used to describe and correctly measure those highly complex multiprofessional situations have only been recently developed and put into practice.In this article, it will be shown how quality in multiprofessional teams can be definded and assessed in daily clinical practice. Core aspects are the choice of a nursing theory, quality assurance measures, and quality management. One possible option of quality assurance is the use of standard operating procedures (SOPs). Quality can ultimately only be achieved if professional groups think beyond their boundaries, minimize errors, and establish and live out instructions and SOPs.

  17. Promoting the Implementation of an Evidence-Based Intervention for Adolescent Marijuana Abuse in Community Settings: Testing the Use of Intensive Quality Assurance

    ERIC Educational Resources Information Center

    Henggeler, Scott W.; Sheidow, Ashli J.; Cunningham, Phillippe B.; Donohue, Bradley C.; Ford, Julian D.

    2008-01-01

    The development and evaluation of effective strategies for transporting evidence-based practices to community-based clinicians has become a research and policy priority. Using multisystemic therapy programs as a platform, an experimental design examined the capacity of an Intensive Quality Assurance (IQA) system to promote therapist implementation…

  18. Quality Assurance Procedures for ModCat Database Code Files

    SciTech Connect

    Siciliano, Edward R.; Devanathan, Ram; Guillen, Zoe C.; Kouzes, Richard T.; Schweppe, John E.

    2014-04-01

    The Quality Assurance procedures used for the initial phase of the Model Catalog Project were developed to attain two objectives, referred to as “basic functionality” and “visualization.” To ensure the Monte Carlo N-Particle model input files posted into the ModCat database meet those goals, all models considered as candidates for the database are tested, revised, and re-tested.

  19. 10 CFR 71.103 - Quality assurance organization.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... location or locations where activities are performed, the organizational structure for executing the... the organizational structure, the individual(s) assigned the responsibility for assuring effective... performing quality assurance functions must have sufficient authority and organizational freedom to—...

  20. 10 CFR 71.103 - Quality assurance organization.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... location or locations where activities are performed, the organizational structure for executing the... the organizational structure, the individual(s) assigned the responsibility for assuring effective... performing quality assurance functions must have sufficient authority and organizational freedom to—...

  1. Endorsing good quality assurance practices in molecular pathology: risks and recommendations for diagnostic laboratories and external quality assessment providers.

    PubMed

    Tembuyser, Lien; Dequeker, Elisabeth M C

    2016-01-01

    Quality assurance is an indispensable element in a molecular diagnostic laboratory. The ultimate goal is to warrant patient safety. Several risks that can compromise high quality procedures are at stake, from sample collection to the test performed by the laboratory, the reporting of test results to clinicians, and the organization of effective external quality assessment schemes. Quality assurance should therefore be safeguarded at each level and should imply a holistic multidisciplinary approach. This review aims to provide an overview of good quality assurance practices and discusses certain risks and recommendations to promote and improve quality assurance for both diagnostic laboratories and for external quality assessment providers. The number of molecular targets is continuously rising, and new technologies are evolving. As this poses challenges for clinical implementation and increases the demand for external quality assessment, the formation of an international association for improving quality assurance in molecular pathology is called for.

  2. MoniQA: a general approach to monitor quality assurance

    NASA Astrophysics Data System (ADS)

    Jacobs, J.; Deprez, T.; Marchal, G.; Bosmans, H.

    2006-03-01

    MoniQA ("Monitor Quality Assurance") is a new, non-commercial, independent quality assurance software application developed in our medical physics team. It is a complete Java TM - based modular environment for the evaluation of radiological viewing devices and it thus fits in the global quality assurance network of our (film less) radiology department. The purpose of the software tool is to guide the medical physicist through an acceptance protocol and the radiologist through a constancy check protocol by presentation of the necessary test patterns and by automated data collection. Data are then sent to a central management system for further analysis. At the moment more than 55 patterns have been implemented, which can be grouped in schemes to implement protocols (i.e. AAPMtg18, DIN and EUREF). Some test patterns are dynamically created and 'drawn' on the viewing device with random parameters as is the case in a recently proposed new pattern for constancy testing. The software is installed on 35 diagnostic stations (70 monitors) in a film less radiology department. Learning time was very limited. A constancy check -with the new pattern that assesses luminance decrease, resolution problems and geometric distortion- takes only 2 minutes and 28 seconds per monitor. The modular approach of the software allows the evaluation of new or emerging test patterns. We will report on the software and its usability: practicality of the constancy check tests in our hospital and on the results from acceptance tests of viewing stations for digital mammography.

  3. Quality assurance: Importance of systems and standard operating procedures.

    PubMed

    Manghani, Kishu

    2011-01-01

    It is mandatory for sponsors of clinical trials and contract research organizations alike to establish, manage and monitor their quality control and quality assurance systems and their integral standard operating procedures and other quality documents to provide high-quality products and services to fully satisfy customer needs and expectations. Quality control and quality assurance systems together constitute the key quality systems. Quality control and quality assurance are parts of quality management. Quality control is focused on fulfilling quality requirements, whereas quality assurance is focused on providing confidence that quality requirements are fulfilled. The quality systems must be commensurate with the Company business objectives and business model. Top management commitment and its active involvement are critical in order to ensure at all times the adequacy, suitability, effectiveness and efficiency of the quality systems. Effective and efficient quality systems can promote timely registration of drugs by eliminating waste and the need for rework with overall financial and social benefits to the Company.

  4. Quality assurance: Importance of systems and standard operating procedures

    PubMed Central

    Manghani, Kishu

    2011-01-01

    It is mandatory for sponsors of clinical trials and contract research organizations alike to establish, manage and monitor their quality control and quality assurance systems and their integral standard operating procedures and other quality documents to provide high-quality products and services to fully satisfy customer needs and expectations. Quality control and quality assurance systems together constitute the key quality systems. Quality control and quality assurance are parts of quality management. Quality control is focused on fulfilling quality requirements, whereas quality assurance is focused on providing confidence that quality requirements are fulfilled. The quality systems must be commensurate with the Company business objectives and business model. Top management commitment and its active involvement are critical in order to ensure at all times the adequacy, suitability, effectiveness and efficiency of the quality systems. Effective and efficient quality systems can promote timely registration of drugs by eliminating waste and the need for rework with overall financial and social benefits to the Company. PMID:21584180

  5. Quality assurance and control in the production and static tests of the solid rocket boosters for the Space Shuttle

    NASA Technical Reports Server (NTRS)

    Cerny, O. F.

    1979-01-01

    The paper surveys the various aspects of design and overhaul of the solid rocket boosters. It is noted that quality control is an integral part of the design specifications. Attention is given to the production process which is optimized towards highest quality. Also discussed is the role of the DCA (Defense Contract Administration) in inspecting the products of subcontractors, noting that the USAF performs this role for prime contractors. Fabrication and construction of the booster is detailed with attention given to the lining of the booster cylinder and the mixing of the propellant and the subsequent X-ray inspection.

  6. 49 CFR 179.7 - Quality assurance program.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Quality assurance program. 179.7 Section 179.7... Reports § 179.7 Quality assurance program. (a) At a minimum, each tank car facility shall have a quality... tank car; and (3) Prevents non-conformities from recurring. (b) At a minimum, the quality...

  7. SU-F-BRE-16: VMAT Commissioning and Quality Assurance (QA) of An Elekta Synergy-STM Linac Using ICOM Test HarnessTM

    SciTech Connect

    Nguyen, A; Rajaguru, P; He, R; Yang, C; Kaurin, D; Paul, T; Plowman, A

    2014-06-15

    Purpose: To establish a set of tests based on the iCOM software that can be used to commission and perform periodic QA of VMAT delivery on the Elekta Synergy-S, commonly known as the Beam Modulator (BM). Methods: iCOM is used to create and deliver customized treatment fields to characterize the system in terms of 1) MLC positioning accuracy under static and dynamic delivery with full gantry rotation, 2) MLC positioning with known errors, 3) Maximum dose rate, 4) Maximum MLC speed, 5) Maximum gantry speed, 6) Synchronization: gantry speed versus dose rate, and 7) Synchronization: MLC speed versus dose rate. The resulting images were captured on the iView GT and exported in DICOM format to Dosimetry Check™ system for visual and quantitative analysis. For the initial commissioning phase, the system tests described should be supplemented with extensive patient QAs covering all clinically relevant treatment sites. Results: The system performance test suite showed that on our Synergy-S, MLC positioning was accurate under both static and dynamic deliveries. Intentional errors of 1 mm were also easily identified on both static and dynamic picket fence tests. Maximum dose rate was verified with stop watch to be consistently between 475-480 MU/min. Maximum gantry speed and MLC speed were 5.5 degree/s and 2.5 cm/s respectively. After accounting for beam flatness, both synchronization tests, gantry versus dose rate and MLC speed versus dose rate, were successful as the fields were uniform across the strips and there were no obvious cold/hot spots. Conclusion: VMAT commissioning and quality assurance should include machine characterization tests in addition to patient QAs. Elekta iCOM is a valuable tool for the design of customized VMAT field with specific MU, MLC leaf positions, dose rate, and indirect control of MLC and gantry speed at each of its control points.

  8. A simple quality assurance test tool for the visual verification of light and radiation field congruent using electronic portal images device and computed radiography

    PubMed Central

    2012-01-01

    Background The radiation field on most megavoltage radiation therapy units are shown by a light field projected through the collimator by a light source mounted inside the collimator. The light field is traditionally used for patient alignment. Hence it is imperative that the light field is congruent with the radiation field. Method A simple quality assurance tool has been designed for rapid and simple test of the light field and radiation field using electronic portal images device (EPID) or computed radiography (CR). We tested this QA tool using Varian PortalVision and Elekta iViewGT EPID systems and Kodak CR system. Results Both the single and double exposure techniques were evaluated, with double exposure technique providing a better visualization of the light-radiation field markers. The light and radiation congruency could be detected within 1 mm. This will satisfy the American Association of Physicists in Medicine task group report number 142 recommendation of 2 mm tolerance. Conclusion The QA tool can be used with either an EPID or CR to provide a simple and rapid method to verify light and radiation field congruence. PMID:22452821

  9. 40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Quality Assurance and Quality Control... and Quality Control Procedures 1. Quality Assurance/Quality Control Program Develop and implement a quality assurance/quality control (QA/QC) program for the continuous emission monitoring systems,...

  10. 40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Quality Assurance and Quality Control... and Quality Control Procedures 1. Quality Assurance/Quality Control Program Develop and implement a quality assurance/quality control (QA/QC) program for the continuous emission monitoring systems,...

  11. 40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Quality Assurance and Quality Control... and Quality Control Procedures 1. Quality Assurance/Quality Control Program Develop and implement a quality assurance/quality control (QA/QC) program for the continuous emission monitoring systems,...

  12. 40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Quality Assurance and Quality Control... and Quality Control Procedures 1. Quality Assurance/Quality Control Program Develop and implement a quality assurance/quality control (QA/QC) program for the continuous emission monitoring systems,...

  13. Flight Dynamics Mission Support and Quality Assurance Process

    NASA Technical Reports Server (NTRS)

    Oh, InHwan

    1996-01-01

    This paper summarizes the method of the Computer Sciences Corporation Flight Dynamics Operation (FDO) quality assurance approach to support the National Aeronautics and Space Administration Goddard Space Flight Center Flight Dynamics Support Branch. Historically, a strong need has existed for developing systematic quality assurance using methods that account for the unique nature and environment of satellite Flight Dynamics mission support. Over the past few years FDO has developed and implemented proactive quality assurance processes applied to each of the six phases of the Flight Dynamics mission support life cycle: systems and operations concept, system requirements and specifications, software development support, operations planing and training, launch support, and on-orbit mission operations. Rather than performing quality assurance as a final step after work is completed, quality assurance has been built in as work progresses in the form of process assurance. Process assurance activities occur throughout the Flight Dynamics mission support life cycle. The FDO Product Assurance Office developed process checklists for prephase process reviews, mission team orientations, in-progress reviews, and end-of-phase audits. This paper will outline the evolving history of FDO quality assurance approaches, discuss the tailoring of Computer Science Corporations's process assurance cycle procedures, describe some of the quality assurance approaches that have been or are being developed, and present some of the successful results.

  14. Automated Quality Assurance of Online NIR Analysers

    PubMed Central

    Aaljoki, Kari

    2005-01-01

    Modern NIR analysers produce valuable data for closed-loop process control and optimisation practically in real time. Thus it is highly important to keep them in the best possible shape. Quality assurance (QA) of NIR analysers is an interesting and complex issue because it is not only the instrument and sample handling that has to be monitored. At the same time, validity of prediction models has to be assured. A system for fully automated QA of NIR analysers is described. The system takes care of collecting and organising spectra from various instruments, relevant laboratory, and process management system (PMS) data. Validation of spectra is based on simple diagnostics values derived from the spectra. Predictions are validated against laboratory (LIMS) or other online analyser results (collected from PMS). The system features automated alarming, reporting, trending, and charting functions for major key variables for easy visual inspection. Various textual and graphical reports are sent to maintenance people through email. The software was written with Borland Delphi 7 Enterprise. Oracle and PMS ODBC interfaces were used for accessing LIMS and PMS data using appropriate SQL queries. It will be shown that it is possible to take actions even before the quality of predictions is seriously affected, thus maximising the overall uptime of the instrument. PMID:18924628

  15. Automated Quality Assurance of Online NIR Analysers.

    PubMed

    Aaljoki, Kari

    2005-01-01

    Modern NIR analysers produce valuable data for closed-loop process control and optimisation practically in real time. Thus it is highly important to keep them in the best possible shape. Quality assurance (QA) of NIR analysers is an interesting and complex issue because it is not only the instrument and sample handling that has to be monitored. At the same time, validity of prediction models has to be assured. A system for fully automated QA of NIR analysers is described. The system takes care of collecting and organising spectra from various instruments, relevant laboratory, and process management system (PMS) data. Validation of spectra is based on simple diagnostics values derived from the spectra. Predictions are validated against laboratory (LIMS) or other online analyser results (collected from PMS). The system features automated alarming, reporting, trending, and charting functions for major key variables for easy visual inspection. Various textual and graphical reports are sent to maintenance people through email. The software was written with Borland Delphi 7 Enterprise. Oracle and PMS ODBC interfaces were used for accessing LIMS and PMS data using appropriate SQL queries. It will be shown that it is possible to take actions even before the quality of predictions is seriously affected, thus maximising the overall uptime of the instrument.

  16. Radiographic Film Processing Quality Assurance: A Self-Teaching Workbook. Quality Assurance Series.

    ERIC Educational Resources Information Center

    Goldman, Lee W.

    This workbook has been designed for use in conjunction with the manual, "Photographic Quality Assurance in Diagnostic Radiology, Nuclear Medicine and Radiation Therapy." Presented are several typical problems arising from the existence of variability and fluctuations in the automatic processing of radiographs, which unless corrected, can…

  17. 48 CFR 246.408 - Single-agency assignments of Government contract quality assurance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... of Government contract quality assurance. 246.408 Section 246.408 Federal Acquisition Regulations... ASSURANCE Government Contract Quality Assurance 246.408 Single-agency assignments of Government contract quality assurance....

  18. Dental technicians: regulation and quality assurance.

    PubMed

    Newsome, P R H

    2011-01-08

    For many years, dental technicians were largely self-regulated and left to work without any undue interference from, or legislation by, outside authorities. This situation has changed somewhat dramatically in recent years, primarily as a result of a) mandatory General Dental Council (GDC) registration of UK-based dental technicians and b) the requirement to comply with certain EC directives governing the provision of dental appliances. There seems to be some confusion, however, about these various changes and the ensuing ramifications for dental practitioners. The purpose of this paper is firstly to clarify the various regulatory issues currently surrounding technician registration and the provision of laboratory work ('Made in Britain' or otherwise) and secondly to explore the various internationally-recognised quality assurance standards that can be applied to the production of such work in order to assist dentists in gauging quality-related claims made by dental laboratories, both in the UK and overseas.

  19. [Cross-sectoral quality assurance in ambulatory care].

    PubMed

    Albrecht, Martin; Loos, Stefan; Otten, Marcus

    2013-01-01

    Overcoming rigid sectoral segmentation in healthcare has also become a health policy target in quality assurance. With the Act to Enhance Competition in Statutory Health Insurance (GKV-WSG) coming into effect, quality assurance measures are to be designed in a cross-sectoral fashion for in- and outpatient sectors equally. An independent institution is currently mandated to develop specific quality indicators for eleven indications. For three of these operating tests have already been commissioned by the Federal Joint Committee. This article depicts the major results of a feasibility study, including a compliance cost estimate, for the aforementioned indications of cross-sectoral quality assurance (cQA). In conclusion, a number of both practical and conceptual basic challenges are still to be resolved prior to the full implementation of cQA, such as a sufficient specification to activate documentation requirements and an inspection system capable of separating actual quality problems from documentary deficits. So far, a comprehensive cost-utility analysis of cQA has not been provided, in particular with comparison to existing QA systems. In order to optimise cost and utility of cQA an evidence-based approach is required for both the extension of cQA areas and for QA provisions.

  20. Quality assurance in laser-Doppler flowmetry applied to dentistry

    NASA Astrophysics Data System (ADS)

    Kaulich, Theodor W.; Koerber, Erich

    1996-12-01

    Laser-doppler flowmetry (LDF) is a diagnostic method for checking and judging vitality in tissues. In dentistry, with the help of LDF, there can be investigated short-term or long-term changes of the oral microcirculation. Defects in the LDF equipment which go undiscovered lead to changes in the quality of the biosignals and hamper diagnosis. Reliable and reproducible results are only obtained if the LDF equipment concerned there exists a standardized quality assurance program. There has been developed and tested a method for constancy checks in LDF measurements. The investigation shows that before each clinical application of an LDF equipment careful testing is necessary.

  1. 222-S Laboratory Quality Assurance Plan. Revision 1

    SciTech Connect

    Meznarich, H.K.

    1995-07-31

    This Quality Assurance Plan provides,quality assurance (QA) guidance, regulatory QA requirements (e.g., 10 CFR 830.120), and quality control (QC) specifications for analytical service. This document follows the U.S Department of Energy (DOE) issued Hanford Analytical Services Quality Assurance Plan (HASQAP). In addition, this document meets the objectives of the Quality Assurance Program provided in the WHC-CM-4-2, Section 2.1. Quality assurance elements required in the Guidelines and Specifications for Preparing Quality Assurance Program Plans (QAMS-004) and Interim Guidelines and Specifications for Preparing Quality Assurance Project Plans (QAMS-005) from the US Environmental Protection Agency (EPA) are covered throughout this document. A quality assurance index is provided in the Appendix A. This document also provides and/or identifies the procedural information that governs laboratory operations. The personnel of the 222-S Laboratory and the Standards Laboratory including managers, analysts, QA/QC staff, auditors, and support staff shall use this document as guidance and instructions for their operational and quality assurance activities. Other organizations that conduct activities described in this document for the 222-S Laboratory shall follow this QA/QC document.

  2. Quality Assurance for Essential Climate Variables

    NASA Astrophysics Data System (ADS)

    Folkert Boersma, K.; Muller, Jan-Peter

    2015-04-01

    Satellite data are of central interest to the QA4ECV project. Satellites have revolutionized the Earth's observation system of climate change and air quality over the past three decades, providing continuous data for the entire Earth. However, many users of these data are lost in the fog as to the quality of these satellite data. Because of this, the European Union expressed in its 2013 FP7 Space Research Call a need for reliable, traceable, and understandable quality information on satellite data records that could serve as a blueprint contribution to a future Copernicus Climate Change Service. The potential of satellite data to benefit climate change and air quality services is too great to be ignored. QA4ECV therefore bridges the gap between end-users of satellite data and the satellite data products. We are developing an internationally acceptable Quality Assurance (QA) framework that provides understandable and traceable quality information for satellite data used in climate and air quality services. Such a framework should deliver the historically linked long-term data sets that users need, in a format that they can readily use. QA4ECV has approached more than 150 users and suppliers of satellite data to collect their needs and expectations. The project will use their response as a guideline for developing user-friendly tools to obtain information on the completeness, accuracy, and fitness-for-purpose of the satellite datasets. QA4ECV collaborates with 4 joint FP7 Space projects in reaching out to scientists, policy makers, and other end-users of satellite data to improve understanding of the special challenges -and also opportunities- of working with satellite data for climate and air quality purposes. As a demonstration of its capacity, QA4ECV will generate multi-decadal climate data records for 3 atmospheric ECV precursors (nitrogen dioxide, formaldehyde, and carbon monoxide) and 3 land ECVs (albedo, leaf area index and absorbed photosynthetically active

  3. Quality Assurance and Quality Control Practices for Rehabilitation of Sewer and Water Mains

    EPA Science Inventory

    As part of the US Environmental Protection Agency (EPA)’s Aging Water Infrastructure Research Program, several areas of research are being pursued, including a review of quality assurance and quality control (QA/QC) practices and acceptance testing during the installation of reha...

  4. Quality Assurance and Quality Control Practices For Rehabilitation of Sewer and Water Mains

    EPA Science Inventory

    As part of the US Environmental Protection Agency (EPA)’s Aging Water Infrastructure Research Program, several areas of research are being pursued including a review of quality assurance and quality control (QA/QC) practices and acceptance testing during the installation of rehab...

  5. Quality assurance guides health reform in Jordan.

    PubMed

    Abubaker, W; Abdulrahman, M

    1996-01-01

    In November 1995, a World Bank mission went to Jordan to conduct a study of the health sector. The study recommended three strategies to reform the health sector: decentralization of Ministry of Health (MOH) management; improvement of clinical practices, quality of care, and consumer satisfaction; and adoption of treatment protocols and standards. The MOH chose quality assurance (QA) methods and quality management (QM) techniques to accomplish these reforms. The Monitoring and QA Directorate oversees QA applications within MOH. It also institutes and develops the capacity of local QA units in the 12 governorates. The QA units implement and monitor day-to-day QA activities. The QM approach encompasses quality principles: establish objectives; use a systematic approach; teach lessons learned and applicable research; use QA training to teach quality care, quality improvement, and patient satisfaction; educate health personnel about QM approaches; use assessment tools and interviews; measure the needs and expectations of local health providers and patients; ensure feedback on QA improvement projects; ensure valid and reliable data; monitor quality improvement efforts; standardize systemic data collection and outcomes; and establish and disseminate QA standards and performance improvement efforts. The Jordan QA Project has helped with the successful institutionalization of a QA system at both the central and local levels. The bylaws of the QA councils and committees require team participation in the decision-making process. Over the last two years, the M&QA Project has adopted 21 standards for nursing, maternal and child health care centers, pharmacies, and medications. The Balqa pilot project has developed 44 such protocols. Quality improvement (COUGH) studies have examined hyper-allergy, analysis of patient flow rate, redistribution of nurses, vaccine waste, and anemic pregnant women. There are a considerable number of on-going clinical and non-clinical COUGH studies

  6. 48 CFR 2146.270 - FEGLI Program quality assurance requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... MANAGEMENT, FEDERAL EMPLOYEES GROUP LIFE INSURANCE FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Quality Requirements 2146.270 FEGLI Program quality assurance requirements. (a) The... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false FEGLI Program...

  7. The Value of Student Engagement for Higher Education Quality Assurance

    ERIC Educational Resources Information Center

    Coates, Hamish

    2005-01-01

    As the principles and practices of quality assurance are further implanted in higher education, methodological questions about how to understand and manage quality become increasingly important. This paper argues that quality assurance determinations need to take account of how and to what extent students engage with activities that are likely to…

  8. Institutional Response to the Swedish Model of Quality Assurance.

    ERIC Educational Resources Information Center

    Nilsson, Karl-Axel; Wahlen, Staffan

    2000-01-01

    Evaluates the Swedish model of quality assurance of higher education by examining the response of institutions to 27 quality audits and 19 follow-up interviews. Discusses the relationship between top-down and bottom-up approaches to internal quality assurance and suggests that, with growing professionalization, more limited result-oriented audits…

  9. Quality Assurance and e-Learning: Blue Skies and Pragmatism

    ERIC Educational Resources Information Center

    Oliver, Ron

    2005-01-01

    This paper considers the role of quality assurance in e-learning; reflecting on the conditions necessary for successful e-learning. It reviews some of the current international work on quality assurance in this area and goes on to consider the ways in which the quality of a process or activity can be assessed--focusing on the use of benchmarking…

  10. Quality Assurance in Higher Education as a Political Process

    ERIC Educational Resources Information Center

    Skolnik, Michael L.

    2010-01-01

    The procedures commonly employed for quality assurance in higher education are designed as if the endeavour were a technical process, whereas it may be more useful to view it as a political process. For example, quality assurance requires making choices among competing conceptions of quality, and in so doing privileges some interests over others.…

  11. 48 CFR 2146.270 - FEGLI Program quality assurance requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... MANAGEMENT, FEDERAL EMPLOYEES GROUP LIFE INSURANCE FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Quality Requirements 2146.270 FEGLI Program quality assurance requirements. (a) The... 48 Federal Acquisition Regulations System 6 2013-10-01 2013-10-01 false FEGLI Program...

  12. Educational Quality Assurance in Universities: An Enhanced Model.

    ERIC Educational Resources Information Center

    Boyle, Patrick; Bowden, John A.

    1997-01-01

    Presents a model of quality assurance for colleges and universities, distilled from key concepts in the literature about quality assurance and higher education culture and practice. The model has continuous quality improvement in student learning at its center, and includes elements of institutional values, faculty evaluation and development,…

  13. 10 CFR 72.140 - Quality assurance requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... component will perform satisfactorily in service. Quality assurance includes quality control, which... 10 Energy 2 2010-01-01 2010-01-01 false Quality assurance requirements. 72.140 Section 72.140... SPENT NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE...

  14. 10 CFR 830.121 - Quality Assurance Program (QAP).

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 4 2011-01-01 2011-01-01 false Quality Assurance Program (QAP). 830.121 Section 830.121 Energy DEPARTMENT OF ENERGY NUCLEAR SAFETY MANAGEMENT Quality Assurance Requirements § 830.121 Quality..., unless it is approved or rejected by DOE at an earlier date. (2) Modify the QAP as directed by DOE....

  15. 10 CFR 830.121 - Quality Assurance Program (QAP).

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 4 2012-01-01 2012-01-01 false Quality Assurance Program (QAP). 830.121 Section 830.121 Energy DEPARTMENT OF ENERGY NUCLEAR SAFETY MANAGEMENT Quality Assurance Requirements § 830.121 Quality..., unless it is approved or rejected by DOE at an earlier date. (2) Modify the QAP as directed by DOE....

  16. 10 CFR 830.121 - Quality Assurance Program (QAP).

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 4 2014-01-01 2014-01-01 false Quality Assurance Program (QAP). 830.121 Section 830.121 Energy DEPARTMENT OF ENERGY NUCLEAR SAFETY MANAGEMENT Quality Assurance Requirements § 830.121 Quality..., unless it is approved or rejected by DOE at an earlier date. (2) Modify the QAP as directed by DOE....

  17. Data Validation & Laboratory Quality Assurance for Region 9

    EPA Pesticide Factsheets

    In all hazardous site investigations, it is essential to know the quality of the data used for decision-making purposes. Validation of data requires that appropriate quality assurance and quality control (QA/QC) procedures be followed.

  18. Quality assurance in gastrointestinal endoscopy: An Egyptian experience.

    PubMed

    Gado, Ahmed S; Ebeid, Basel A; Axon, Anthony T

    2016-12-01

    Over the last four decades, gastrointestinal endoscopy has become of paramount importance to diagnose, treat and prevent diseases of the digestive tract. Practice variation, however, is likely to have an important effect on the effectiveness of endoscopy and can impair the delivery of high-quality endoscopic procedures. There have been increasing demands to assess the quality of service and track and improve patient outcomes. Quality assurance has paved its way into professional guidelines for physicians. Developing a modern endoscopy unit demands the institution of a quality assurance programme, continuous training and monitoring of service delivery. This article describes our experience in implementing a quality assurance programme in endoscopy in a secondary care government hospital in Egypt. The implementation of quality assurance and improvement programme can lead to dramatic improvements in the quality of endoscopic care and patient outcomes. Quality assurance and continual improvement can be applied in developing countries.

  19. HELIOS Critical Design Review: Quality Assurance

    NASA Technical Reports Server (NTRS)

    Benoehr, H. C.; Herholz, J.; Prem, H.; Mann, D.; Reichert, L.; Rupp, W.; Campbell, D.; Boettger, H.; Zerwes, G.; Kurvin, C.

    1972-01-01

    The following is an account of the activities of the Quality Assurance (QA) department of the project management office highlighting some of the ways in which it controls QA of the subcontractors on one hand and reports on Quality to GfW (Gesellschaft fur Weltraumforschung) on the other hand. The basic document prepared by MBB (Messerschmitt-Bolkow-Blohm) for QA activities is 1. The QA plan based on GfW 002. The QA department is responsible moreover for monitoring and making decisions about the quality of parts and materials and the governing document for this activity is 2. The Parts and Materials Control Plan based on GfW 001 - the reliability program provisions, as well as GfW 002. A brief survey of the contents of the QA Plan is shown. It should be noted that QA activity dealing with parts procurement is partially covered in a separate presentation entitled "Hi-Rel Parts". Supplementary quality documents are shown.

  20. Assuring the Quality of Test Results in the Field of Nuclear Techniques and Ionizing Radiation. The Practical Implementation of Section 5.9 of the EN ISO/IEC 17025 Standard

    NASA Astrophysics Data System (ADS)

    Cucu, Daniela; Woods, Mike

    2008-08-01

    The paper aims to present a practical approach for testing laboratories to ensure the quality of their test results. It is based on the experience gained in assessing a large number of testing laboratories, discussing with management and staff, reviewing results obtained in national and international PTs and ILCs and exchanging information in the EA laboratory committee. According to EN ISO/IEC 17025, an accredited laboratory has to implement a programme to ensure the quality of its test results for each measurand. Pre-analytical, analytical and post-analytical measures shall be applied in a systematic manner. They shall include both quality control and quality assurance measures. When designing the quality assurance programme a laboratory should consider pre-analytical activities (like personnel training, selection and validation of test methods, qualifying equipment), analytical activities ranging from sampling, sample preparation, instrumental analysis and post-analytical activities (like decoding, calculation, use of statistical tests or packages, management of results). Designed on different levels (analyst, quality manager and technical manager), including a variety of measures, the programme shall ensure the validity and accuracy of test results, the adequacy of the management system, prove the laboratory's competence in performing tests under accreditation and last but not least show the comparability of test results. Laboratory management should establish performance targets and review periodically QC/QA results against them, implementing appropriate measures in case of non-compliance.

  1. SAPHIRE 8 Volume 6 - Quality Assurance

    SciTech Connect

    C. L. Smith; R. Nims; K. J. Kvarfordt

    2011-03-01

    The Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) Version 8 is a software application developed for performing a complete probabilistic risk assessment using a personal computer running the Microsoft Windows™ operating system. SAPHIRE 8 is funded by the U.S. Nuclear Regulatory Commission (NRC). The role of the INL in this project is that of software developer and tester. This development takes place using formal software development procedures and is subject to quality assurance (QA) processes. The purpose of this document is to describe how the SAPHIRE software QA is performed for Version 8, what constitutes its parts, and limitations of those processes. In addition, this document describes the Independent Verification and Validation that was conducted for Version 8 as part of an overall QA process.

  2. SAPHIRE 8 Software Quality Assurance Plan

    SciTech Connect

    Curtis Smith

    2010-02-01

    This Quality Assurance (QA) Plan documents the QA activities that will be managed by the INL related to JCN N6423. The NRC developed the SAPHIRE computer code for performing probabilistic risk assessments (PRAs) using a personal computer (PC) at the Idaho National Laboratory (INL) under Job Code Number (JCN) L1429. SAPHIRE started out as a feasibility study for a PRA code to be run on a desktop personal PC and evolved through several phases into a state-of-the-art PRA code. The developmental activity of SAPHIRE was the result of two concurrent important events: The tremendous expansion of PC software and hardware capability of the 90s and the onset of a risk-informed regulation era.

  3. Quality assurance - no margin for error

    SciTech Connect

    Thomas, R.L.; Smith, C.F.; Grant, W.D.

    1982-01-01

    Quality assurance (QA), a critical component of a hydraulic fracturing treatment, must be performed prior to and during the job. Failure to follow QA procedures may result in added well costs and poor production. It begins during the design and ends after the completion of the job. The importance of QA has been magnified due to the increased size and complexity fracturing treatments. It is a tool used to insure that fluids, proppants, and equipment meet the increased demands placed upon them. This study discusses several steps take in order to provide QA. An explanation of procedures used during the job design and prior to the job is given. A discussion of procedures and trouble shooting techniques used prior to and during the job also is presented. The sensors and computer system used in order to monitor QA data also are discussed.

  4. Hanford analytical services quality assurance requirements documents

    SciTech Connect

    Hyatt, J.E.

    1997-09-25

    Hanford Analytical Services Quality Assurance Requirements Document (HASQARD) is issued by the Analytical Services, Program of the Waste Management Division, US Department of Energy (US DOE), Richland Operations Office (DOE-RL). The HASQARD establishes quality requirements in response to DOE Order 5700.6C (DOE 1991b). The HASQARD is designed to meet the needs of DOE-RL for maintaining a consistent level of quality for sampling and field and laboratory analytical services provided by contractor and commercial field and laboratory analytical operations. The HASQARD serves as the quality basis for all sampling and field/laboratory analytical services provided to DOE-RL through the Analytical Services Program of the Waste Management Division in support of Hanford Site environmental cleanup efforts. This includes work performed by contractor and commercial laboratories and covers radiological and nonradiological analyses. The HASQARD applies to field sampling, field analysis, and research and development activities that support work conducted under the Hanford Federal Facility Agreement and Consent Order Tri-Party Agreement and regulatory permit applications and applicable permit requirements described in subsections of this volume. The HASQARD applies to work done to support process chemistry analysis (e.g., ongoing site waste treatment and characterization operations) and research and development projects related to Hanford Site environmental cleanup activities. This ensures a uniform quality umbrella to analytical site activities predicated on the concepts contained in the HASQARD. Using HASQARD will ensure data of known quality and technical defensibility of the methods used to obtain that data. The HASQARD is made up of four volumes: Volume 1, Administrative Requirements; Volume 2, Sampling Technical Requirements; Volume 3, Field Analytical Technical Requirements; and Volume 4, Laboratory Technical Requirements. Volume 1 describes the administrative requirements

  5. 40 CFR 75.21 - Quality assurance and quality control requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Quality assurance and quality control... assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner or... system according to the quality assurance and quality control procedures in appendix B of this part....

  6. 40 CFR 75.21 - Quality assurance and quality control requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Quality assurance and quality control... assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner or... system according to the quality assurance and quality control procedures in appendix B of this part....

  7. 40 CFR 75.21 - Quality assurance and quality control requirements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Quality assurance and quality control... assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner or... system according to the quality assurance and quality control procedures in appendix B of this part....

  8. 40 CFR 75.21 - Quality assurance and quality control requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Quality assurance and quality control... assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner or... system according to the quality assurance and quality control procedures in appendix B of this part....

  9. Quality Assurance Project Plan: Connecticut wetlands study

    SciTech Connect

    Sherman, A.; Gwin, S.

    1991-04-01

    EPA's Wetland Research Program has supported a major effort to study wetlands mitigation projects in the field. The field studies were designed to: (1) evaluate the project plans; (2) compare the projects with natural wetlands in the same land use setting; and (3) describe the development of the projects over time. The information from the studies will be used as technical guidance for setting performance criteria and developing design guidelines for mitigation projects. Pilot studies have been conducted in Oregon, Washington, Florida, and Connecticut. The report presents the methods and associated quality assurance procedures used during the Connecticut study. A major objective of the pilot study was to evaluate the field procedures and the data quality assessment protocols used. The authors are in the process of performing that evaluation. They anticipate that in some cases they will adopt the procedure, while others will be refined or discarded. Therefore, the authors caution the user of the document that, at this point, the EPA makes no claims or endorsement of the use of the field, laboratory, or data quality assessment procedures associated with the study.

  10. Photovoltaic system criteria documents. Volume 2: Quality assurance criteria for photovoltaic applications

    NASA Technical Reports Server (NTRS)

    Koenig, John C.; Billitti, Joseph W.; Tallon, John M.

    1979-01-01

    Quality assurance criteria are described for manufacturers and installers of solar photovoltaic tests and applications. Quality oriented activities are outlined to be pursued by the contractor/subcontractor to assure the physical and operational quality of equipment produced is included. In the broad sense, guidelines are provided for establishing a QA organization if none exists. Mainly, criteria is provided to be considered in any PV quality assurance plan selected as appropriate by the responsible Field Center. A framework is established for a systematic approach to ensure that photovoltaic tests and applications are constructed in a timely and cost effective manner.

  11. Mission assurance increased with regression testing

    NASA Astrophysics Data System (ADS)

    Lang, R.; Spezio, M.

    Knowing what to test is an important attribute in any testing campaign, especially when it has to be right or the mission could be in jeopardy. The New Horizons mission, developed and operated by the John Hopkins University Applied Physics Laboratory, received a planned major upgrade to their Mission Operations and Control (MOC) ground system architecture. Early in the mission planning it was recognized that the ground system platform would require an upgrade to assure continued support of technology used for spacecraft operations. With the planned update to the six year operational ground architecture from Solaris 8 to Solaris 10, it was critical that the new architecture maintain critical operations and control functions. The New Horizons spacecraft is heading to its historic rendezvous with Pluto in July 2015 and then proceeding into the Kuiper Belt. This paper discusses the Independent Software Acceptance Testing (ISAT) Regression test campaign that played a critical role to assure the continued success of the New Horizons mission. The New Horizons ISAT process was designed to assure all the requirements were being met for the ground software functions developed to support the mission objectives. The ISAT team developed a test plan with a series of test case designs. The test objectives were to verify that the software developed from the requirements functioned as expected in the operational environment. As the test cases were developed and executed, a regression test suite was identified at the functional level. This regression test suite would serve as a crucial resource in assuring the operational system continued to function as required with such a large scale change being introduced. Some of the New Horizons ground software changes required modifications to the most critical functions of the operational software. Of particular concern was the new MOC architecture (Solaris 10) is Intel based and little endian, and the legacy architecture (Solaris 8) was SPA

  12. Gas generation matrix depletion quality assurance project plan

    SciTech Connect

    1998-05-01

    The Los Alamos National Laboratory (LANL) is to provide the necessary expertise, experience, equipment and instrumentation, and management structure to: Conduct the matrix depletion experiments using simulated waste for quantifying matrix depletion effects; and Conduct experiments on 60 cylinders containing simulated TRU waste to determine the effects of matrix depletion on gas generation for transportation. All work for the Gas Generation Matrix Depletion (GGMD) experiment is performed according to the quality objectives established in the test plan and under this Quality Assurance Project Plan (QAPjP).

  13. Role of Informatics in Patient Safety and Quality Assurance.

    PubMed

    Nakhleh, Raouf E

    2015-06-01

    Quality assurance encompasses monitoring daily processes for accurate, timely, and complete reports in surgical pathology. Quality assurance also includes implementation of policies and procedures that prevent or detect errors in a timely manner. This article presents uses of informatics in quality assurance. Three main foci are critical to the general improvement of diagnostic surgical pathology. First is the application of informatics to specimen identification with lean methods for real-time statistical control of specimen receipt and processing. Second is the development of case reviews before sign-out. Third is the development of information technology in communication of results to assure treatment in a timely manner.

  14. Quality measures and assurance for AI (Artificial Intelligence) software

    NASA Technical Reports Server (NTRS)

    Rushby, John

    1988-01-01

    This report is concerned with the application of software quality and evaluation measures to AI software and, more broadly, with the question of quality assurance for AI software. Considered are not only the metrics that attempt to measure some aspect of software quality, but also the methodologies and techniques (such as systematic testing) that attempt to improve some dimension of quality, without necessarily quantifying the extent of the improvement. The report is divided into three parts Part 1 reviews existing software quality measures, i.e., those that have been developed for, and applied to, conventional software. Part 2 considers the characteristics of AI software, the applicability and potential utility of measures and techniques identified in the first part, and reviews those few methods developed specifically for AI software. Part 3 presents an assessment and recommendations for the further exploration of this important area.

  15. A Rotational Blended Learning Model: Enhancement and Quality Assurance

    ERIC Educational Resources Information Center

    Ghoul, Said

    2013-01-01

    Research on blended learning theory and practice is growing nowadays with a focus on the development, evaluation, and quality assurance of case studies. However, the enhancement of blended learning existing models, the specification of their online parts, and the quality assurance related specifically to them have not received enough attention.…

  16. The Landscape of Quality Assurance in Distance Education

    ERIC Educational Resources Information Center

    Scull, W. Reed; Kendrick, David; Shearer, Rick; Offerman, Dana

    2011-01-01

    Distance education permeates the field of professional and continuing education to such an extent that quality assurance (QA) is a topic no distance educator or administrator should avoid. Quality assurance is an issue not just for continuing education but also for higher education generally. Given the disruptive impact of distance education and…

  17. Focusing on Quality Assurance--The Profession's Collective Efforts.

    ERIC Educational Resources Information Center

    Klyop, John S.

    1989-01-01

    The American Dental Association Office of Quality Assurance's current programs include liaison with national health organizations, a comprehensive report of quality assurance, a health policy agenda for the American people, encouragement of peer review organizations, a Joint Commission on Accreditation of Healthcare Organizations, and…

  18. 40 CFR Appendix C to Part 61 - Quality Assurance Procedures

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 8 2011-07-01 2011-07-01 false Quality Assurance Procedures C Appendix C to Part 61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...—Quality Assurance Procedures Procedure 1—Determination of Adequate Chromatographic Peak Resolution In...

  19. QUALITY ASSURANCE IN RESEARCH LABORATORIES: RULES AND REASON

    EPA Science Inventory

    Quality Assurance in Research Laboratories: Rules and Reason

    Ron Rogers, Quality Assurance and Records Manager, Environmental Carcinogenesis Division, NHEERL/ORD/US EPA, Research Triangle Park, NC, 27709

    To anyone who has actively participated in research, as I have...

  20. Internal Quality Assurance Benchmarking. ENQA Workshop Report 20

    ERIC Educational Resources Information Center

    Blackstock, Douglas; Burquel, Nadine; Comet, Nuria; Kajaste, Matti; dos Santos, Sergio Machado; Marcos, Sandra; Moser, Marion; Ponds, Henri; Scheuthle, Harald; Sixto, Luis Carlos Velon

    2012-01-01

    The Internal Quality Assurance group of ENQA (IQA Group) has been organising a yearly seminar for its members since 2007. The main objective is to share experiences concerning the internal quality assurance of work processes in the participating agencies. The overarching theme of the 2011 seminar was how to use benchmarking as a tool for…

  1. Monitoring and Assuring the Quality of Digital Aerial Data

    NASA Technical Reports Server (NTRS)

    Christopherson, Jon

    2007-01-01

    This viewgraph presentation explains the USGS plan for monitoring and assuring the quality of digital aerial data. The contents include: 1) History of USGS Aerial Imaging Involvement; 2) USGS Research and Results; 3) Outline of USGS Quality Assurance Plan; 4) Other areas of Interest; and 5) Summary

  2. 40 CFR Appendix C to Part 61 - Quality Assurance Procedures

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Quality Assurance Procedures C Appendix...—Quality Assurance Procedures Procedure 1—Determination of Adequate Chromatographic Peak Resolution In this....” Procedure 2—Procedure for Field Auditing GC Analysis Responsibilities of audit supervisor and analyst at...

  3. Quality Assurance of E-learning. ENQA Workshop Report 14

    ERIC Educational Resources Information Center

    Grifoll, Josep; Huertas, Esther; Prades, Anna; Rodriguez, Sebastian; Rubin, Yuri; Mulder, Fred; Ossiannilsson, Ebba

    2010-01-01

    E-learning in the European Higher Education Area has stampeded its way to the foreground of the Quality Assurance (QA) forum, and has become a key issue among quality assurance agencies and institutions in the European Higher Education Area (EHEA). Because internet-based learning is currently such a relevant topic, there is a dire need for the…

  4. Understanding Quality Assurance: A Cross Country Case Study

    ERIC Educational Resources Information Center

    Choon Boey Lim, Fion

    2008-01-01

    Purpose: The purpose of this paper is to examine the level of understanding between an Australian university and its offshore partner institution, on quality assurance. It attempts to highlight the dynamics of quality assurance policy implementation within and across institutions for an offshore degree. Design/methodology/approach: The study used…

  5. Operational Environmental Monitoring Program Quality Assurance Project Plan

    SciTech Connect

    Perkins, C.J.

    1994-08-01

    This Quality Assurance Project Plan addresses the quality assurance requirements for the activities associated with the preoperational and operational environmental monitoring performed by Westinghouse Hanford Company as it implements the Operational Environmental Monitoring program. This plan applies to all sampling and monitoring activities performed by Westinghouse Hanford Company in implementing the Operational Environmental Monitoring program at the Hanford Site.

  6. Democratisation and Quality Assurance in South African Higher Education

    ERIC Educational Resources Information Center

    Symes, Ashley

    2006-01-01

    The article interprets a particular set of debates on whether quality assurance in South African higher education widens democracy or not. The interpretation explores the extent to which higher education quality assurance fulfils three conditions posited for democracy (inclusion, participation and enhancement), drawing in as points of reference…

  7. Quality Assurance Toolkit for Distance Higher Education Institutions and Programmes

    ERIC Educational Resources Information Center

    Rama, Kondapalli, Ed.; Hope, Andrea, Ed.

    2009-01-01

    The Commonwealth of Learning is proud to partner with the Sri Lankan Ministry of Higher Education and UNESCO to produce this "Quality Assurance Toolkit for Distance Higher Education Institutions and Programmes". The Toolkit has been prepared with three features. First, it is a generic document on quality assurance, complete with a…

  8. Quality Assurance in South Africa: A Reply to John Mammen

    ERIC Educational Resources Information Center

    le Grange, L.

    2006-01-01

    In this article I point out that prominence given to higher education quality assurance by contemporary states might be viewed in the context of the ascendance of neoliberalism over the past few decades and a concomitant culture of performativity. However, I argue for a shift in the angle of vision on performativity and quality assurance through a…

  9. 45 CFR 800.402 - Contract quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 45 Public Welfare 3 2013-10-01 2013-10-01 false Contract quality assurance. 800.402 Section 800.402 Public Welfare Regulations Relating to Public Welfare (Continued) OFFICE OF PERSONNEL MANAGEMENT MULTI-STATE PLAN PROGRAM Compliance § 800.402 Contract quality assurance. (a) General. This...

  10. 45 CFR 800.402 - Contract quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 45 Public Welfare 3 2014-10-01 2014-10-01 false Contract quality assurance. 800.402 Section 800.402 Public Welfare Regulations Relating to Public Welfare (Continued) OFFICE OF PERSONNEL MANAGEMENT MULTI-STATE PLAN PROGRAM Compliance § 800.402 Contract quality assurance. (a) General. This...

  11. Policy of Quality Assurance in Hong Kong Preschools

    ERIC Educational Resources Information Center

    Dora, Ho Choi-wa

    2007-01-01

    This article discusses the sources, processes and impact of the quality assurance policy implemented in Hong Kong preschools. Regarded as a sort of policy alignment between the subsystems of pre-primary, primary and secondary education, the introduction of a quality assurance policy has been directly and indirectly transforming the settlements in…

  12. Quality Assurance of Joint Programmes. ENQA Workshop Report 19

    ERIC Educational Resources Information Center

    Frederiks, Mark; Grifoll, Josep; Hiltunen, Kirsi; Hopbach, Achim

    2012-01-01

    In view of the Bologna ministerial conference to be held in April 2012 in Bucharest, ENQA organised a seminar in September 2011 on Quality Assurance of Joint Programmes in collaboration with the Austrian Accreditation Council (OAR). The purpose of this seminar was twofold: first, to analyse the experience already gained in quality assurance of…

  13. Quality assurance program plan for radionuclide airborne emissions monitoring

    SciTech Connect

    Boom, R.J.

    1995-03-01

    This Quality Assurance Program Plan identifies quality assurance program requirements and addresses the various Westinghouse Hanford Company organizations and their particular responsibilities in regards to sample and data handling of airborne emissions. The Hanford Site radioactive airborne emissions requirements are defined in National Emissions Standards for Hazardous Air Pollutants (NESHAP), Code of Federal Regulations, Title 40, Part 61, Subpart H (EPA 1991a). Reporting of the emissions to the US Department of Energy is performed in compliance with requirements of US Department of Energy, Richland Operations Office Order 5400.1, General Environmental Protection Program (DOE-RL 1988). This Quality Assurance Program Plan is prepared in accordance with and to the requirements of QAMS-004/80, Guidelines and Specifications for Preparing Quality Assurance Program Plans (EPA 1983). Title 40 CFR Part 61, Appendix B, Method 114, Quality Assurance Methods (EPA 1991b) specifies the quality assurance requirements and that a program plan should be prepared to meet the requirements of this regulation. This Quality Assurance Program Plan identifies NESHAP responsibilities and how the Westinghouse Hanford Company Environmental, Safety, Health, and Quality Assurance Division will verify that the methods are properly implemented.

  14. Current Trends in European Quality Assurance. ENQA Workshop Report 8

    ERIC Educational Resources Information Center

    Bozo, Dhurata; Damian, Radu; Gonzalez, Cecilia de la Rosa; Helle, Emmi; Imoda, Franco; Kohler, Alexander; Papazoglou, Vassilios J.; Dalmau, Gemma Rauret; Shopov, Todor

    2009-01-01

    The present report is a product of two ENQA (European Association for Quality Assurance in Higher Education) seminars, held in 2007, on current trends in European Quality Assurance. The first seminar, hosted by the Bulgarian National Evaluation and Accreditation Agency (NEAA), examined the situation in South-Eastern Europe. The second seminar…

  15. Regulating and Quality-Assuring VET: International Developments. Research Report

    ERIC Educational Resources Information Center

    Misko, Josie

    2015-01-01

    The opening-up of the market for education and training, including vocational education and training (VET), has increased the importance of regulation and quality assurance mechanisms in ensuring the integrity of qualifications. This report investigates approaches to the regulation and quality assurance of vocational education and training in a…

  16. Quality Assurance Program Plan for radionuclide airborne emissions monitoring

    SciTech Connect

    Vance, L.M.

    1993-07-01

    This Quality Assurance Program Plan (QAPP) describes the quality assurance requirements and responsibilities for radioactive airborne emissions measurements activities from regulated stacks are controlled at the Hanford Site. Detailed monitoring requirements apply to stacks exceeding 1% of the standard of 10 mrem annual effective dose equivalent to the maximally exposed individual from operations of the Hanford Site.

  17. KCBX Quality Assurance Project Plan - October 2014

    EPA Pesticide Factsheets

    This revised plan's standards for data quality, sampling and testing methods, and task management guide the implementation of Ambient Air Monitoring by URS Corporation at the KCBX Terminals Company North and South Terminals in Chicago, Ill.

  18. KCBX Quality Assurance Project Plan - February 2014

    EPA Pesticide Factsheets

    This plan's standards for data quality, sampling and testing methods, and task management guide the implementation of Ambient Air Monitoring, by URS Corporation, at the KCBX Terminals Company North and South Terminals in Chicago, IL.

  19. Chiropractic quality assurance: standards and guidelines

    PubMed Central

    Gatterman, Meridel I; Dobson, Thomas P; LeFevbre, Ron

    2001-01-01

    Chiropractic quality assurance involves development of both clinical guidelines and standards. Confusion generated by poor differentiation of guidelines from standards contributes to mistrust of the guideline development process. Guidelines are considered to be recommendations that allow for flexibility and individual patient differences. Standards are more binding and require a high level of supporting evidence. While guidelines serve as educational tools to improve the quality of practice, standards that outline minimum competency are used more as administrative tools on which to base policy. Barriers to development of clinical guidelines and standards include fear that they will create prescriptive “cookbook” practice, and the distrust that guidelines are developed primarily for cost containment. Clinicians also criticize guidelines developed by academics that don't relate to practice, and those based on evidence that lacks clinical relevance. Conflicting guidelines perceived to be based on strong bias or conflict of interest are also suspect. To reduce barriers to acceptance and implementation, guidelines should be inclusive, patient-centered, and based on a variety of evidence and clinical experience.

  20. EPA Guidance for Geospatially Related Quality Assurance Project Plans

    EPA Pesticide Factsheets

    This March 2003 document discusses EPA's Quality Assurance (QA) Project Plan as a tool for project managers and planners to document the type and quality of data and information needed for making environmental decisions

  1. Internal Quality Assurance--Enhancing Quality Culture. ENQA Workshop Report 16

    ERIC Educational Resources Information Center

    ENQA (European Association for Quality Assurance in Higher Education), 2010

    2010-01-01

    The European Association for Quality Assurance in Higher Education (ENQA), in cooperation with the Quality Assurance Agency (QAA, UK), organised a seminar on theme "Internal Quality Assurance--Enhancing quality culture" which was held on 8-9 June, 2010 in London, United Kingdom. The seminar marked the fourth annual meeting of the ENQA…

  2. [Quality measurement using administrative data in mandatory quality assurance].

    PubMed

    Heller, Günther; Szecsenyi, Joachim; Willms, Gerald; Broge, Björn

    2014-01-01

    For several years, the use of administrative data in mandatory quality measurement has been requested by several stakeholders in Germany. Main advantages of using administrative data include the reduction of documentary expenditures and the possibility to perform longitudinal quality analyses across different healthcare units. After a short introduction, a brief overview of the current use of administrative data for mandatory quality assurance as well as current developments is given, which will then be further exemplified by decubital ulcer prophylaxis. By using administrative data coding expenditures in this clinical area could be reduced by nine million data fields. At the same time the population analysed was expanded resulting in a more than tenfold increase in potentially quality-relevant events. Finally, perspectives, further developments, possibilities as well as limits of quality measurement with administrative data are discussed.

  3. 48 CFR 46.402 - Government contract quality assurance at source.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... quality assurance at source. 46.402 Section 46.402 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality Assurance 46.402 Government contract quality assurance at source. Agencies shall perform contract quality assurance,...

  4. 48 CFR 46.403 - Government contract quality assurance at destination.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... quality assurance at destination. 46.403 Section 46.403 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality Assurance 46.403 Government contract quality assurance at destination. (a) Government contract quality assurance that can...

  5. Research and development quality assurance planning

    SciTech Connect

    Hoke, P.B.

    1990-05-14

    Planning for quality assurance (QA) in research and development (R D) is like stealing eggs without waking up the chickens. The QA program should be as unobtrusive as possible. Researchers require a QA program that affords them an environment capable of supporting repeatable experiments with accurate data without unduly stifling their creative abilities. Careful advance planning ensures that the intensity of control provided by quality-related systems is commensurate with the importance and scope of the activities being performed. Good scientific practices applied to small bench-scale projects may require minimal additional controls. As projects increase in size and complexity the controls imposed through planning must, by necessity, be increased. Research and development QA planning, just like any other planning, involves all affected individuals. The application of control systems is determined by factors such as customer or sponsor requirements, the importance of an item or activity to the experiment's success, and the organizational complexity of the project. Many larger experiments are highly dependent on quality-related support activities such as calibration, engineering design, and inspection provided by organizations outside the R D group. Since, in most cases, the expense of support activities is taken directly from funds available for research, it is important for the researchers to be involved in the planning efforts to help determine and agree with the level of QA effort required. A single plan will often suffice for organizations engaged in large numbers of similar experiments. Complex experiments may require unique QA plans or additions to existing plans. Once implemented, the R D QA plans, like any others, require audits or surveillances and may require revisions if the scope of the experiment changes. 1 ref., 1 fig.

  6. Quality Assurance in the European Higher Education Area: The Emergence of a German Market for Quality Assurance Agencies

    ERIC Educational Resources Information Center

    Serrano-Velarde, Kathia E.

    2008-01-01

    Most European countries have introduced systematic quality assurance as part of an overall governance reform aimed at enhancing universities' autonomy. Researchers and economic entrepreneurs tend, however, to underestimate the political dimension of accreditation and evaluation when they consider the contribution of quality assurance to the…

  7. SU-D-304-05: Validation of Low-Dose-Tail Modeling for Proton Pencil Beam Spot Scanning Using a Quality Assurance Test Pattern

    SciTech Connect

    Lin, L; Huang, S; Kang, M; Solberg, T; McDonough, J; Ainsley, C

    2015-06-15

    Purpose: The purpose of this manuscript is to demonstrate the utility of a comprehensive test pattern in validating calculation models of the low-dose tails of proton pencil beam scanning (PBS) spots. Such a pattern has been used previously for quality assurance purposes to assess spot shape and location, and for determining monitor units. Methods: In this study, a scintillation detector was used to measure the test pattern in air at isocenter for two proton beam energies (115 and 225 MeV) of two IBA universal nozzles (UN). Planar measurements were compared with calculated dose distribution based on the weighted superposition of spot profiles previously measured using a pair-magnification method. Results: Including the halo component below 1% of the central dose is shown to improve the gamma-map comparison between calculation and measurement from 94.9% to 98.4% using 2 mm/2% criteria for the 115 MeV proton beam of UN #1. In contrast, including the halo component below 1% of the central dose does not improve the gamma agreement for the 115 MeV proton beam of UN #2, due to the cutoff of the halo component at off-axis locations. When location-dependent spot profiles are used for calculation instead of spot profiles at central axis, the gamma agreement is improved from 98.0% to 99.5% using 2 mm/2% criteria. The cutoff of the halo component is smaller at higher energies, and is not observable for the 225 MeV proton beam for UN #2. Conclusion: In conclusion, the use of a comprehensive test pattern can facilitate the validation of the halo component of proton PBS spots at off axis locations. The cutoff of the halo component should be taken into consideration for large fields or PBS systems that intend to trim spot profiles using apertures. This work was supported by the US Army Medical Research and Materiel Command under Contract Agreement No. DAMD17-W81XWH-07-2-0121 and W81XWH-09-2-0174.

  8. Quality assurance tool: taking a whole-system approach.

    PubMed

    Dowling, Claire; Patel, Seraphim Jr

    2014-11-27

    The London Cancer Alliance (LCA) has developed the Quality Clinical Board Exception Report (QCBER), a tool that supports delivery of quality assurance across its member organisations through its quality assurance framework and escalation protocol. The process improves quality assurance and performance in terms of patient safety, patient satisfaction and clinical outcomes. This article describes how implementation of a robust quality assurance process supported by a simple tool can help healthcare organisations improve patient care and avoid duplication when sharing quality information among providers and across healthcare systems. It also explains how application of the tool can help organisations build evidence of best practice in the five essential Care Quality Commission areas: safety, effectiveness, care, responsiveness and good management.

  9. AVLIS Production Plant Preliminary Quality Assurance Plan and Assessment

    SciTech Connect

    Not Available

    1984-11-15

    This preliminary Quality Assurance Plan and Assessment establishes the Quality Assurance requirements for the AVLIS Production Plant Project. The Quality Assurance Plan defines the management approach, organization, interfaces, and controls that will be used in order to provide adequate confidence that the AVLIS Production Plant design, procurement, construction, fabrication, installation, start-up, and operation are accomplished within established goals and objectives. The Quality Assurance Program defined in this document includes a system for assessing those elements of the project whose failure would have a significant impact on safety, environment, schedule, cost, or overall plant objectives. As elements of the project are assessed, classifications are provided to establish and assure that special actions are defined which will eliminate or reduce the probability of occurrence or control the consequences of failure. 8 figures, 18 tables.

  10. Quality Assurance Framework for Mini-Grids

    SciTech Connect

    Baring-Gould, Ian; Burman, Kari; Singh, Mohit; Esterly, Sean; Mutiso, Rose; McGregor, Caroline

    2016-11-01

    Providing clean and affordable energy services to the more than 1 billion people globally who lack access to electricity is a critical driver for poverty reduction, economic development, improved health, and social outcomes. More than 84% of populations without electricity are located in rural areas where traditional grid extension may not be cost-effective; therefore, distributed energy solutions such as mini-grids are critical. To address some of the root challenges of providing safe, quality, and financially viable mini-grid power systems to remote customers, the U.S. Department of Energy (DOE) teamed with the National Renewable Energy Laboratory (NREL) to develop a Quality Assurance Framework (QAF) for isolated mini-grids. The QAF for mini-grids aims to address some root challenges of providing safe, quality, and affordable power to remote customers via financially viable mini-grids through two key components: (1) Levels of service: Defines a standard set of tiers of end-user service and links them to technical parameters of power quality, power availability, and power reliability. These levels of service span the entire energy ladder, from basic energy service to high-quality, high-reliability, and high-availability service (often considered 'grid parity'); (2) Accountability and performance reporting framework: Provides a clear process of validating power delivery by providing trusted information to customers, funders, and/or regulators. The performance reporting protocol can also serve as a robust monitoring and evaluation tool for mini-grid operators and funding organizations. The QAF will provide a flexible alternative to rigid top-down standards for mini-grids in energy access contexts, outlining tiers of end-user service and linking them to relevant technical parameters. In addition, data generated through implementation of the QAF will provide the foundation for comparisons across projects, assessment of impacts, and greater confidence that will drive

  11. Quality assurance of a helical tomotherapy machine

    NASA Astrophysics Data System (ADS)

    Fenwick, J. D.; Tomé, W. A.; Jaradat, H. A.; Hui, S. K.; James, J. A.; Balog, J. P.; DeSouza, C. N.; Lucas, D. B.; Olivera, G. H.; Mackie, T. R.; Paliwal, B. R.

    2004-07-01

    Helical tomotherapy has been developed at the University of Wisconsin, and 'Hi-Art II' clinical machines are now commercially manufactured. At the core of each machine lies a ring-gantry-mounted short linear accelerator which generates x-rays that are collimated into a fan beam of intensity-modulated radiation by a binary multileaf, the modulation being variable with gantry angle. Patients are treated lying on a couch which is translated continuously through the bore of the machine as the gantry rotates. Highly conformal dose-distributions can be delivered using this technique, which is the therapy equivalent of spiral computed tomography. The approach requires synchrony of gantry rotation, couch translation, accelerator pulsing and the opening and closing of the leaves of the binary multileaf collimator used to modulate the radiation beam. In the course of clinically implementing helical tomotherapy, we have developed a quality assurance (QA) system for our machine. The system is analogous to that recommended for conventional clinical linear accelerator QA by AAPM Task Group 40 but contains some novel components, reflecting differences between the Hi-Art devices and conventional clinical accelerators. Here the design and dosimetric characteristics of Hi-Art machines are summarized and the QA system is set out along with experimental details of its implementation. Connections between this machine-based QA work, pre-treatment patient-specific delivery QA and fraction-by-fraction dose verification are discussed.

  12. The NCI Thesaurus quality assurance life cycle.

    PubMed

    de Coronado, Sherri; Wright, Lawrence W; Fragoso, Gilberto; Haber, Margaret W; Hahn-Dantona, Elizabeth A; Hartel, Francis W; Quan, Sharon L; Safran, Tracy; Thomas, Nicole; Whiteman, Lori

    2009-06-01

    The National Cancer Institute Enterprise Vocabulary Services (NCI EVS) uses a wide range of quality assurance (QA) techniques to maintain and extend NCI Thesaurus (NCIt). NCIt is a reference terminology and biomedical ontology used in a growing number of NCI and other systems that extend from translational and basic research through clinical care to public information and administrative activities. Both automated and manual QA techniques are employed throughout the editing and publication cycle, which includes inserting and editing NCIt in NCI Metathesaurus. NCI EVS conducts its own additional periodic and ongoing content QA. External reviews, and extensive evaluation by and interaction with EVS partners and other users, have also played an important part in the QA process. There have always been tensions and compromises between meeting the needs of dependent systems and providing consistent and well-structured content; external QA and feedback have been important in identifying and addressing such issues. Currently, NCI EVS is exploring new approaches to broaden external participation in the terminology development and QA process.

  13. An Alternative View of Quality Assurance and Enhancement

    ERIC Educational Resources Information Center

    Wong, Viola Yuk-Yue

    2012-01-01

    This paper attempts to deal with the elusive nature of quality in quality management, using a case study to examine quality control measures implemented in an academic context and to show an emergent framework for quality enhancement. This paper introduces the concept of the ecology of quality assurance and examines efforts to maintain and advance…

  14. Is Quality Assurance in Higher Education Contextually Relative?

    ERIC Educational Resources Information Center

    Ntshoe, I.; Higgs, P.; Wolhuter, C. C.; Higgs, L. G.

    2010-01-01

    This article examines notions of quality and quality assurance in higher education. It does this by raising questions such as whether quality in higher education is the same as, for example, quality of clothing or the quality of meat in local butcheries. The article questions the assumption that if certain things, such as criteria or…

  15. A software tool for quality assurance of computed/digital radiography (CR/DR) systems

    NASA Astrophysics Data System (ADS)

    Desai, Nikunj; Valentino, Daniel J.

    2011-03-01

    The recommended methods to test the performance of computed radiography (CR) systems have been established by The American Association of Physicists in Medicine, Report No. 93, "Acceptance Testing and Quality Control of Photostimulable Storage Phosphor Imaging Systems". The quality assurance tests are categorized by how frequently they need to be performed. Quality assurance of CR systems is the responsibility of the facility that performs the exam and is governed by the state in which the facility is located. For Example, the New York State Department of Health has established a guide which lists the tests that a CR facility must perform for quality assurance. This study aims at educating the reader about the new quality assurance requirements defined by the state. It further demonstrates an easy to use software tool, henceforth referred to as the Digital Physicist, developed to aid a radiologic facility in conforming with state guidelines and monitoring quality assurance of CR/DR imaging systems. The Digital Physicist provides a vendor independent procedure for quality assurance of CR/DR systems. Further it, generates a PDF report with a brief description of these tests and the obtained results.

  16. 48 CFR 46.408 - Single-agency assignments of Government contract quality assurance.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... the Department of Commerce. (b) Agencies requiring quality assurance support for acquiring these... of Government contract quality assurance. 46.408 Section 46.408 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract...

  17. 48 CFR 46.408 - Single-agency assignments of Government contract quality assurance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... the Department of Commerce. (b) Agencies requiring quality assurance support for acquiring these... of Government contract quality assurance. 46.408 Section 46.408 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract...

  18. 48 CFR 46.408 - Single-agency assignments of Government contract quality assurance.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... the Department of Commerce. (b) Agencies requiring quality assurance support for acquiring these... of Government contract quality assurance. 46.408 Section 46.408 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract...

  19. 48 CFR 46.408 - Single-agency assignments of Government contract quality assurance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... the Department of Commerce. (b) Agencies requiring quality assurance support for acquiring these... of Government contract quality assurance. 46.408 Section 46.408 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract...

  20. Quality assurance in health care: past, present and future.

    PubMed

    Bilawka, E; Craig, B J

    2003-08-01

    Quality of health care delivery is a growing concern globally given current budget restraints and increasing demands on health care providers. The variety of quality assurance and quality management activities equals the numerous ways health care practitioners of all genres provide health care. Dental hygienists around the world must be knowledgeable about quality assurance and management in health care as it is a significant factor in the evolution of the dental hygiene profession and the quality of oral health care provided by dental hygienists. The objective of this research was to conduct a literature review on quality assurance and quality management. A MEDLINE search from 1966 to 2002 was conducted. The search resulted in approximately 145 articles. Additional references from works generated by the search were also obtained. The literature revealed information on the background and history of quality assurance and quality management. Much of the literature was devoted to discussions of the validity, reliability and effectiveness of most prominent quality management activities being utilised in health care today. The investigation revealed numerous issues and barriers surrounding quality management. This article concludes with suggestions for future directions of quality assurance and quality management.

  1. Trusted Computing Exemplar: Quality Assurance Plan

    DTIC Science & Technology

    2014-12-12

    correct spelling , etc.); those issues are currently covered in other documents. 15. SUBJECT TERMS Machinery control systems, MCS, life cycle security...quality means more than just source code testing (such as conformance to documentation standards, correct spelling , etc.), but those issues are

  2. 40 CFR 160.35 - Quality assurance unit.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... standard operating procedures were made without proper authorization and documentation. (6) Review the final study report to assure that such report accurately describes the methods and standard operating... LABORATORY PRACTICE STANDARDS Organization and Personnel § 160.35 Quality assurance unit. (a) A...

  3. 40 CFR 160.35 - Quality assurance unit.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... standard operating procedures were made without proper authorization and documentation. (6) Review the final study report to assure that such report accurately describes the methods and standard operating... LABORATORY PRACTICE STANDARDS Organization and Personnel § 160.35 Quality assurance unit. (a) A...

  4. Cui Bono? The Relevance and Impact of Quality Assurance

    ERIC Educational Resources Information Center

    Massaro, Vin

    2010-01-01

    External quality assurance of universities exists to assure society that higher education standards are adequate and, in an increasingly global market, that they are comparable internationally. Although society has accepted an implicit compact in giving autonomy to universities in return for their dispassionate service to it, there has been an…

  5. Delivery quality assurance with ArcCHECK

    SciTech Connect

    Neilson, Christopher; Klein, Michael; Barnett, Rob; Yartsev, Slav

    2013-04-01

    Radiation therapy requires delivery quality assurance (DQA) to ensure that treatment is accurate and closely follows the plan. We report our experience with the ArcCHECK phantom and investigate its potential optimization for the DQA process. One-hundred seventy DQA plans from 84 patients were studied. Plans were classified into 2 groups: those with the target situated on the diodes of the ArcCHECK (D plans) and those with the target situated at the center (C plans). Gamma pass rates for 8 target sites were examined. The parameters used to analyze the data included 3%/3 mm with the Van Dyk percent difference criteria (VD) on, 3%/3 mm with the VD off, 2%/2 mm with the VD on, and x/3 mm with the VD on and the percentage dosimetric agreement “x” for diode plans adjusted. D plans typically displayed maximum planned dose (MPD) on the cylindrical surface containing ArcCHECK diodes than center plans, resulting in inflated gamma pass rates. When this was taken into account by adjusting the percentage dosimetric agreement, C plans outperformed D plans by an average of 3.5%. ArcCHECK can streamline the DQA process, consuming less time and resources than radiographic films. It is unnecessary to generate 2 DQA plans for each patient; a single center plan will suffice. Six of 8 target sites consistently displayed pass rates well within our acceptance criteria; the lesser performance of head and neck and spinal sites can be attributed to marginally lower doses and increased high gradient of plans.

  6. Introduction of Syphilis Point-of-Care Tests, from Pilot Study to National Programme Implementation in Zambia: A Qualitative Study of Healthcare Workers' Perspectives on Testing, Training and Quality Assurance.

    PubMed

    Ansbro, Éimhín M; Gill, Michelle M; Reynolds, Joanna; Shelley, Katharine D; Strasser, Susan; Sripipatana, Tabitha; Tshaka Ncube, Alexander; Tembo Mumba, Grace; Terris-Prestholt, Fern; Peeling, Rosanna W; Mabey, David

    2015-01-01

    Syphilis affects 1.4 million pregnant women globally each year. Maternal syphilis causes congenital syphilis in over half of affected pregnancies, leading to early foetal loss, pregnancy complications, stillbirth and neonatal death. Syphilis is under-diagnosed in pregnant women. Point-of-care rapid syphilis tests (RST) allow for same-day treatment and address logistical barriers to testing encountered with standard Rapid Plasma Reagin testing. Recent literature emphasises successful introduction of new health technologies requires healthcare worker (HCW) acceptance, effective training, quality monitoring and robust health systems. Following a successful pilot, the Zambian Ministry of Health (MoH) adopted RST into policy, integrating them into prevention of mother-to-child transmission of HIV clinics in four underserved Zambian districts. We compare HCW experiences, including challenges encountered in scaling up from a highly supported NGO-led pilot to a large-scale MoH-led national programme. Questionnaires were administered through structured interviews of 16 HCWs in two pilot districts and 24 HCWs in two different rollout districts. Supplementary data were gathered via stakeholder interviews, clinic registers and supervisory visits. Using a conceptual framework adapted from health technology literature, we explored RST acceptance and usability. Quantitative data were analysed using descriptive statistics. Key themes in qualitative data were explored using template analysis. Overall, HCWs accepted RST as learnable, suitable, effective tools to improve antenatal services, which were usable in diverse clinical settings. Changes in training, supervision and quality monitoring models between pilot and rollout may have influenced rollout HCW acceptance and compromised testing quality. While quality monitoring was integrated into national policy and training, implementation was limited during rollout despite financial support and mentorship. We illustrate that new

  7. Technical aspects of the Naval Dosimetry Center quality assurance programme.

    PubMed

    St John, T J; Cassata, J R; Blake, P K; Wallace, W H; Minniti, R

    2006-01-01

    The purpose of this paper is to describe the technical aspects of the Naval Dosimetry Center (NDC) quality programme. The Navy has been formally monitoring personnel for occupational exposure to ionising radiation since at least 1946. The current system, the DT-702/PD, is the Harshaw 8840 holder and 8841 card. New card and holder checks are performed to verify that the correct LiF elements and holder filters are in the correct location and are of the correct composition. Element correction coefficient (ECC) magnitude and repeatability are also verified. Several quality assurance parameters are checked by a specially designed shipping machine. Calibration cards are used to calibrate each reader and quality control cards are inserted throughout a group of field cards to verify reader operation during the read process. The success of the programme is measured by annual proficiency tests administered by the National Voluntary Laboratory Accreditation Programme and Pacific Northwest National Laboratories.

  8. SAPHIRE 8 Quality Assurance Software Metrics Report

    SciTech Connect

    Kurt G. Vedros

    2011-08-01

    The purpose of this review of software metrics is to examine the quality of the metrics gathered in the 2010 IV&V and to set an outline for results of updated metrics runs to be performed. We find from the review that the maintenance of accepted quality standards presented in the SAPHIRE 8 initial Independent Verification and Validation (IV&V) of April, 2010 is most easily achieved by continuing to utilize the tools used in that effort while adding a metric of bug tracking and resolution. Recommendations from the final IV&V were to continue periodic measurable metrics such as McCabe's complexity measure to ensure quality is maintained. The four software tools used to measure quality in the IV&V were CodeHealer, Coverage Validator, Memory Validator, Performance Validator, and Thread Validator. These are evaluated based on their capabilities. We attempted to run their latest revisions with the newer Delphi 2010 based SAPHIRE 8 code that has been developed and was successful with all of the Validator series of tools on small tests. Another recommendation from the IV&V was to incorporate a bug tracking and resolution metric. To improve our capability of producing this metric, we integrated our current web reporting system with the SpiraTest test management software purchased earlier this year to track requirements traceability.

  9. Quality Assurance in Post-Secondary Education: Some Common Approaches

    ERIC Educational Resources Information Center

    Law, Dennis Chung Sea

    2010-01-01

    Purpose: The common approaches to quality assurance (QA), as practiced by most post-secondary education institutions for internal quality monitoring and most QA authorities for external quality monitoring (EQM), have been considered by many researchers as having largely failed to address the essence of educational quality. The purpose of this…

  10. IEEE Std 730 Software Quality Assurance: Supporting CMMI-DEV v1.3, Product and Process Quality Assurance

    DTIC Science & Technology

    2011-05-27

    TAG to ISO TC 176 Quality Management • Quality : ASQ, work experience • Software: three books, consulting, work experience • Systems: Telecom & DoD... management activities may be assured in accordance with the clauses of ISO 9001 . ©2011 Walz Map Process Areas to P730 Tasks 20 CMMI has several...frameworks 4 CMMI-DEV IEEE / ISO / IEC 15288 / 12207 Quality Assurance ©2011 Walz IEEE Life Cycle Processes & Artifacts • Systems Life Cycle Processes

  11. Annual Quality Assurance Conference Presentations by Johnathan Beck

    EPA Pesticide Factsheets

    25th Annual Quality Assurance Conference Presentation: Disinfectants/Disinfection Byproducts –Rules and Requirements and Presentation: Long Term 2 Enhanced Surface Water Treatment Rule (LT2) Cryptosporidium Monitoring

  12. Annual Quality Assurance Conference Abstracts by Barbara Marshik

    EPA Pesticide Factsheets

    25th Annual Quality Assurance Conference. Abstracts: Material and Process Conditions for Successful Use of Extractive Sampling Techniques and Certification Methods Errors in the Analysis of NMHC and VOCs in CNG-Based Engine Emissions by Barbara Marshik

  13. Quality Assurance Project Plan for Citizen Science Projects

    EPA Pesticide Factsheets

    The Quality Assurance Project Plan is necessary for every project that collects or uses environmental data. It documents the project planning process and serves as a blueprint for how your project will run.

  14. Master Pump Shutdown MPS Software Quality Assurance Plan (SQAP)

    SciTech Connect

    BEVINS, R.R.

    2000-09-20

    The MPSS Software Quality Assurance (SQAP) describes the tools and strategy used in the development of the MPSS software. The document also describes the methodology for controlling and managing changes to the software.

  15. Reform of Teacher Education and the Problem of Quality Assurance.

    ERIC Educational Resources Information Center

    Barr, Robert D.

    1987-01-01

    Educational reform developments focusing on academic issues are contrasted with those emphasizing teacher performance. The concept of quality assurance in teacher education is considered, as is using student achievement as an indicator of teacher effectiveness. (Author/MT)

  16. Annual Quality Assurance Conference Files by Tom Mancuso

    EPA Pesticide Factsheets

    25th Annual Quality Assurance Conference. Abstract: Learn about the NEW EPA Method 325b for Refinery Fence Line Monitoring and TO-17 Extended for Soil Gas by Tom Mancuso and Abstract: Success Using Alternate Carrier Gases for Volatile Methods

  17. 10 CFR 72.142 - Quality assurance organization.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... activities are performed, the organizational structure for executing the quality assurance program may take... the required authority and organizational freedom. Irrespective of the organizational structure, the... functions of structures, systems, and components which are important to safety. These activities...

  18. 10 CFR 72.142 - Quality assurance organization.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... activities are performed, the organizational structure for executing the quality assurance program may take... the required authority and organizational freedom. Irrespective of the organizational structure, the... functions of structures, systems, and components which are important to safety. These activities...

  19. Lake Champlain TMDL Modeling Quality Assurance Project Plan

    EPA Pesticide Factsheets

    This document presents the quality assurance project plan for providing support to US EPA Region 1 in revising the Lake Champlain Total Maximum Daily Load, under Contract Number EP-C-08-004, Task Order 80.

  20. Integration of Quality Assurance/Quality Control into Quantitative Analysis

    NASA Astrophysics Data System (ADS)

    Bell, Suzanne C.; Moore, Jeff

    1998-07-01

    Modern laboratories, be they in government or industry, operate under strict quality assurance and quality control (QA/QC) guidelines. Yet, these topics are rarely covered in undergraduate laboratories, or are presented as isolated experiments. This fosters the false idea that QA/QC is a separate subject when in actuality it is an integral part of analytical chemistry. It is possible to incorporate QA/QC into existing student laboratories by utilizing blanks, replicates, knowns and spiked samples. Proper use of QA/QC, coupled to an understanding of fundamental chemical principles and statistics strengthens traditional laboratory exercises. Concepts of accuracy and precision are transformed from abstractions into concrete data, and student skills in troubleshooting and problem solving are enhanced.

  1. Quality assurance in toxicology studies in developing countries.

    PubMed

    Morris, C R

    1989-03-01

    As developing countries become more involved in the international chemical trade, they must adhere to certain requirements for importation of their chemicals into foreign countries. These developing countries will be required to provide basic safety information on their chemical products, including data developed from chemical and toxicologic testing. These data must be developed in accordance with the national requirements of the importing country. Many importing countries have adopted the OECD Test Guidelines and the OECD Principles of Good Laboratory Practice (GLP) as primary guidance to assure the quality of laboratory data. These procedures provide a basis for internationally acceptable data. Several countries have incorporated many of these provisions into their national laws or administrative procedures. These procedures describe the process of documenting the conduct of laboratory studies, including recording of data, reporting of study results, and storage of data gathered. This process is intended to assure the quality and integrity of the data so that, if required, the study can be reconstructed by an auditor or an inspector. Details of these procedures and their applicability to the international chemical trade are discussed.

  2. The Columbia River Protection Supplemental Technologies Quality Assurance Project Plan

    SciTech Connect

    Fix, N. J.

    2008-03-12

    Pacific Northwest National Laboratory researchers are working on the Columbia River Protection Supplemental Technologies Project. This project is a U. S. Department of Energy, Office of Environmental Management-funded initiative designed to develop new methods, strategies, and technologies for characterizing, modeling, remediating, and monitoring soils and groundwater contaminated with metals, radionuclides, and chlorinated organics. This Quality Assurance Project Plan provides the quality assurance requirements and processes that will be followed by the Technologies Project staff.

  3. Quality assurance as a managerial innovation: a research perspective.

    PubMed Central

    Kaluzny, A D

    1982-01-01

    Quality assurance is defined and concepts from innovation theory are applied to the study of quality assurance programs. Two distinct although not mutually exclusive perspectives on innovation are considered--the diffusion perspective, focusing on the innovation itself and its implementation, and the adoption perspective, highlighting factors characteristic of the adoption unit (i.e., the organization or individuals within it) that facilitate or impede the adoption process. Directions for future research are suggested. PMID:7118545

  4. Near-facility environmental monitoring quality assurance project plan

    SciTech Connect

    McKinney, S.M.

    1997-11-24

    This Quality Assurance Project Plan addresses the quality assurance requirements for the activities associated with the preoperational and near facility environmental monitoring performed by Waste Management Federal Services, Inc., Northwest Operations and supersedes WHC-EP-0538-2. This plan applies to all sampling and monitoring activities performed by waste management Federal Services, Inc., Northwest Operations in implementing facility environmental monitoring at the Hanford Site.

  5. Internal quality assurance in cervical cytology one laboratory's experience.

    PubMed

    Cross, P A

    1996-02-01

    The results of an internal quality assurance exercise in one cervical cytology laboratory in England are presented, using different types of partial percentage re-screening of cervical smears. An overall false negative dyskaryotic rate of up to 4.3% was demonstrated, with the final cytology report diagnosis differing from the primary screening dignosis in 1.3% of cases. These finding are discussed, with the aim of helping to foster debate on the setting of national laboratory internal quality assurance standards.

  6. Quality Assurance Project Plan for Facility Effluent Monitoring Plan activities

    SciTech Connect

    Frazier, T.P.

    1994-10-20

    This Quality Assurance Project Plan addresses the quality assurance requirements for the activities associated with the Facility Effluent Monitoring Plans, which are part of the overall Hanford Site Environmental Protection Plan. This plan specifically applies to the sampling and analysis activities and continuous monitoring performed for all Facility Effluent Monitoring Plan activities conducted by Westinghouse Hanford Company. It is generic in approach and will be implemented in conjunction with the specific requirements of the individual Facility Effluent Monitoring Plans.

  7. Modified aerospace reliability and quality assurance method for wind turbines

    NASA Technical Reports Server (NTRS)

    Klein, W. E.

    1980-01-01

    The safety, reliability, and quality assurance (SR&QA) approach developed for the first large wind turbine generator project is described. The SR&QA approach was used to assure that the machine would not be hazardous to the public or operating personnel, would operate unattended on a utility grid, would demonstrate reliable operation and would help establish the quality assurance and maintainability requirements for future wind turbine projects. A modified failure modes and effects analysis during the design phase, minimal hardware inspections during parts fabrication, and three simple documents to control activities during machine construction and operation were presented.

  8. Reliability and quality assurance on the MOD 2 wind system

    NASA Technical Reports Server (NTRS)

    Mason, W. E. B.; Jones, B. G.

    1981-01-01

    The Safety, Reliability, and Quality Assurance (R&QA) approach developed for the largest wind turbine generator, the Mod 2, is described. The R&QA approach assures that the machine is not hazardous to the public or to the operating personnel, is operated unattended on a utility grid, demonstrates reliable operation, and helps establish the quality assurance and maintainability requirements for future wind turbine projects. The significant guideline consisted of a failure modes and effects analysis (FMEA) during the design phase, hardware inspections during parts fabrication, and three simple documents to control activities during machine construction and operation.

  9. Quality management system for application of the analytical quality assurance cycle in a research project

    NASA Astrophysics Data System (ADS)

    Camargo, R. S.; Olivares, I. R. B.

    2016-07-01

    The lack of quality assurance and quality control in academic activities have been recognized by the inability to demonstrate reproducibility. This paper aim to apply a quality tool called Analytical Quality Assurance Cycle on a specific research project, supported by a Verification Programme of equipment and an adapted Quality Management System based on international standards, to provide traceability to the data generated.

  10. Measurement quality assurance for beta particle calibrations at NIST

    SciTech Connect

    Soares, C.G.; Pruitt, J.S.

    1993-12-31

    Standardized beta-particle fields have been established in an international standard and have been adopted for use in several U.S. dosimeter and instrument testing standards. Calibration methods and measurement quality assurance procedures employed at the National Institute of Standards and Technology (NIST) for beta-particle calibrations in these reference fields are discussed. The calibration facility including the NIST-automated extrapolation ionization chamber is described, and some sample results of calibrations are shown. Methods for establishing and maintaining traceability to NIST of secondary laboratories are discussed. Currently, there are problems in finding a good method for routine testing of traceability to NIST. Some examples of past testing methods are given and solutions to this problem are proposed.

  11. Sharply notch cylindrical tension specimen for screening plane-strain fracture toughness. I - Influence of fundamental testing variables on notch strength. II Applications in aluminum alloy quality assurance of fracture toughness

    NASA Technical Reports Server (NTRS)

    Jones, M. H.; Bubsey, R. T.; Brown, W. F., Jr.; Bucci, R. J.; Collis, S. F.; Kohm, R. F.; Kaufman, J. G.

    1977-01-01

    A description is presented of studies which have been conducted to establish an improved technology base for a use of the sharply notched cylindrical specimen in quality assurance tests of aluminum alloy products. The results are presented of an investigation of fundamental variables associated with specimen preparation and testing, taking into account the influence of the notch root radius, the eccentricity of loading, the specimen diameter, and the notch depth on the sharp notch strength. Attention is given to the statistical procedures which are necessary to establish correlations between the sharp notch strength and the plane-strain fracture toughness for high-strength aluminum alloys.

  12. 21 CFR 1000.55 - Recommendation for quality assurance programs in diagnostic radiology facilities.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... and continuing education to keep the personnel up-to-date. Practical experience with the techniques... producing the images. Quality assurance actions include both “quality control” techniques and “quality... control techniques are those techniques used in the monitoring (or testing) and maintenance of...

  13. Quality assurance plan for Solar Maximum Mission (SSM) Instruments electronic assembly - HRUV spectrometer/polarimeter

    NASA Technical Reports Server (NTRS)

    1976-01-01

    The quality assurance program demonstrates recognition of the quality aspects and an organized approach to achieve them. It ensures that quality requirements are determined and satisfied throughout all phases of contract performance, including preliminary and engineering design, development, fabrication, processing, assembly, inspection, test, checkout, packaging, shipping, storage, maintenance field use, flight preparations, flight operations and post-flight analysis, as applicable.

  14. Quality Assurance on the Road: Finland and Austria in Comparison

    ERIC Educational Resources Information Center

    Bernhard, Andrea

    2011-01-01

    The ongoing necessity for quality and quality assurance in the entire Bologna process remains one of the main issues for European policy makers. The aims of creating comparable systems and of guaranteeing quality within higher education systems are the reasons for national developments and the eagerness to reform. The situation in two relatively…

  15. Quality Assurance in Psychology Programmes across Europe: Survey and Reflections

    ERIC Educational Resources Information Center

    Marques, J. Frederico

    2013-01-01

    The present article examines how different institutions that offer psychology study cycles across Europe have adopted quality principles and have taken up particular quality assurance initiatives to raise standards and enhance quality. Thirty-eight different institutions from 32 countries who were members of a European psychology network responded…

  16. Quality Assurance in American and British Higher Education: A Comparison.

    ERIC Educational Resources Information Center

    Stanley, Elizabeth C.; Patrick, William J.

    1998-01-01

    Compares quality improvement and accountability processes in the United States and United Kingdom. For the United Kingdom, looks at quality audits, institutional assessment, standards-based quality assurance, and research assessment; in the United States, looks at regional and specialized accreditation, performance indicator systems, academic…

  17. Strategic Planning and Quality Assurance in the Bologna Process

    ERIC Educational Resources Information Center

    Kettunen, Juha; Kantola, Mauri

    2007-01-01

    Strategic planning and quality management have been developed independently of each other, but they meet in practice in many kinds of organisations. Strategic planning and quality assurance integrate different aspects of higher education institutions (HEIs) to ensure high-quality educational outcomes. This paper investigates the role of these two…

  18. Student Involvement in the Egyptian Quality Assurance System

    ERIC Educational Resources Information Center

    Elassy, Noha

    2015-01-01

    Purpose: The purpose of this paper is to study the extent and the quality of student involvement in the quality assurance process (QAP) in Egyptian higher education institutions (HEIs). Design/methodology/approach: In this study, two qualitative methods were used to explore the extent and the quality of student involvement; these were focus groups…

  19. Evolution of Quality Assurance for Clinical Immunohistochemistry in the Era of Precision Medicine: Part 4: Tissue Tools for Quality Assurance in Immunohistochemistry.

    PubMed

    Cheung, Carol C; D'Arrigo, Corrado; Dietel, Manfred; Francis, Glenn D; Fulton, Regan; Gilks, C Blake; Hall, Jacqueline A; Hornick, Jason L; Ibrahim, Merdol; Marchetti, Antonio; Miller, Keith; van Krieken, J Han; Nielsen, Soren; Swanson, Paul E; Taylor, Clive R; Vyberg, Mogens; Zhou, Xiaoge; Torlakovic, Emina E

    2016-12-09

    The numbers of diagnostic, prognostic, and predictive immunohistochemistry (IHC) tests are increasing; the implementation and validation of new IHC tests, revalidation of existing tests, as well as the on-going need for daily quality assurance monitoring present significant challenges to clinical laboratories. There is a need for proper quality tools, specifically tissue tools that will enable laboratories to successfully carry out these processes. This paper clarifies, through the lens of laboratory tissue tools, how validation, verification, and revalidation of IHC tests can be performed in order to develop and maintain high quality "fit-for-purpose" IHC testing in the era of precision medicine. This is the final part of the 4-part series "Evolution of Quality Assurance for Clinical Immunohistochemistry in the Era of Precision Medicine."

  20. Daily quality assurance software for a satellite radiometer system

    NASA Technical Reports Server (NTRS)

    Keegstra, P. B.; Smoot, G. F.; Bennett, C. L.; Aymon, J.; Backus, C.; Deamici, G.; Hinshaw, G.; Jackson, P. D.; Kogut, A.; Lineweaver, C.

    1992-01-01

    Six Differential Microwave Radiometers (DMR) on COBE (Cosmic Background Explorer) measure the large-angular-scale isotropy of the cosmic microwave background (CMB) at 31.5, 53, and 90 GHz. Quality assurance software analyzes the daily telemetry from the spacecraft to ensure that the instrument is operating correctly and that the data are not corrupted. Quality assurance for DMR poses challenging requirements. The data are differential, so a single bad point can affect a large region of the sky, yet the CMB isotropy requires lengthy integration times (greater than 1 year) to limit potential CMB anisotropies. Celestial sources (with the exception of the moon) are not, in general, visible in the raw differential data. A 'quicklook' software system was developed that, in addition to basic plotting and limit-checking, implements a collection of data tests as well as long-term trending. Some of the key capabilities include the following: (1) stability analysis showing how well the data RMS averages down with increased data; (2) a Fourier analysis and autocorrelation routine to plot the power spectrum and confirm the presence of the 3 mK 'cosmic' dipole signal; (3) binning of the data against basic spacecraft quantities such as orbit angle; (4) long-term trending; and (5) dipole fits to confirm the spacecraft attitude azimuth angle.