[Quality control in anesthesiology].

PubMed

Muñoz-Ramón, J M

1995-03-01

The process of quality control and auditing of anesthesiology allows us to evaluate care given by a service and solve problems that are detected. Quality control is a basic element of care giving and is only secondarily an area of academic research; it is therefore a meaningless effort if the information does not serve to improve departmental procedures. Quality assurance procedures assume certain infrastructural requirements and an initial period of implementation and adjustment. The main objectives of quality control are the reduction of morbidity and mortality due to anesthesia, assurance of the availability and proper management of resources and, finally, the well-being and safety of the patient.

Vista/F-16 Multi-Axis Thrust Vectoring (MATV) control law design and evaluation

NASA Technical Reports Server (NTRS)

Zwerneman, W. D.; Eller, B. G.

1994-01-01

For the Multi-Axis Thrust Vectoring (MATV) program, a new control law was developed using multi-axis thrust vectoring to augment the aircraft's aerodynamic control power to provide maneuverability above the normal F-16 angle of attack limit. The control law architecture was developed using Lockheed Fort Worth's offline and piloted simulation capabilities. The final flight control laws were used in flight test to demonstrate tactical benefits gained by using thrust vectoring in air-to-air combat. Differences between the simulator aerodynamics data base and the actual aircraft aerodynamics led to significantly different lateral-directional flying qualities during the flight test program than those identified during piloted simulation. A 'dial-a-gain' flight test control law update was performed in the middle of the flight test program. This approach allowed for inflight optimization of the aircraft's flying qualities. While this approach is not preferred over updating the simulator aerodynamic data base and then updating the control laws, the final selected gain set did provide adequate lateral-directional flying qualities over the MATV flight envelope. The resulting handling qualities and the departure resistance of the aircraft allowed the 422nd_squadron pilots to focus entirely on evaluating the aircraft's tactical utility.

A design procedure and handling quality criteria for lateral directional flight control systems

NASA Technical Reports Server (NTRS)

Stein, G.; Henke, A. H.

1972-01-01

A practical design procedure for aircraft augmentation systems is described based on quadratic optimal control technology and handling-quality-oriented cost functionals. The procedure is applied to the design of a lateral-directional control system for the F4C aircraft. The design criteria, design procedure, and final control system are validated with a program of formal pilot evaluation experiments.

Bel Marin Keys Unit V Expansion of the Hamilton Wetland Restoration Project. Volume 3. Responses to Comments, Final Supplemental Environmental Impact Report/Environmental Impact Statement

DTIC Science & Technology

2003-04-01

include a program for implementing new development and construction site storm water quality controls. The objective of this component is to ensure...impacts (see Storm Water Quality Control, below). The Regional Board has adopted U.S. EPA’s Clean Water Act Section 404(b)(1) "Guidelines for...other Waters of the State. Storm Water Quality Control Storm water is the major source of fresh water to creeks and waterways. Storm water quality is

78 FR 58459 - Revisions to the California State Implementation Plan, Antelope Valley Air Quality Management...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-24

... the California State Implementation Plan, Antelope Valley Air Quality Management District, Santa Barbara County Air Pollution Control District, South Coast Air Quality Management District and Ventura.... SUMMARY: EPA is finalizing approval of revisions to the Antelope Valley Air Quality Management District...

Use of near-infrared spectroscopy and multipoint measurements for quality control of pharmaceutical drug products.

PubMed

Boiret, Mathieu; Chauchard, Fabien

2017-01-01

Near-infrared (NIR) spectroscopy is a non-destructive analytical technique that enables better-understanding and optimization of pharmaceutical processes and final drug products. The use in line is often limited by acquisition speed and sampling area. This work focuses on performing a multipoint measurement at high acquisition speed at the end of the manufacturing process on a conveyor belt system to control both the distribution and the content of active pharmaceutical ingredient within final drug products, i.e., tablets. A specially designed probe with several collection fibers was developed for this study. By measuring spectral and spatial information, it provides physical and chemical knowledge on the final drug product. The NIR probe was installed on a conveyor belt system that enables the analysis of a lot of tablets. The use of these NIR multipoint measurement probes on a conveyor belt system provided an innovative method that has the potential to be used as a new paradigm to ensure the drug product quality at the end of the manufacturing process and as a new analytical method for the real-time release control strategy. Graphical abstract Use of near-infrared spectroscopy and multipoint measurements for quality control of pharmaceutical drug products.

Research to Assembly Scheme for Satellite Deck Based on Robot Flexibility Control Principle

NASA Astrophysics Data System (ADS)

Guo, Tao; Hu, Ruiqin; Xiao, Zhengyi; Zhao, Jingjing; Fang, Zhikai

2018-03-01

Deck assembly is critical quality control point in final satellite assembly process, and cable extrusion and structure collision problems in assembly process will affect development quality and progress of satellite directly. Aimed at problems existing in deck assembly process, assembly project scheme for satellite deck based on robot flexibility control principle is proposed in this paper. Scheme is introduced firstly; secondly, key technologies on end force perception and flexible docking control in the scheme are studied; then, implementation process of assembly scheme for satellite deck is described in detail; finally, actual application case of assembly scheme is given. Result shows that compared with traditional assembly scheme, assembly scheme for satellite deck based on robot flexibility control principle has obvious advantages in work efficiency, reliability and universality aspects etc.

The application of neural network PID controller to control the light gasoline etherification

NASA Astrophysics Data System (ADS)

Cheng, Huanxin; Zhang, Yimin; Kong, Lingling; Meng, Xiangyong

2017-06-01

Light gasoline etherification technology can effectively improve the quality of gasoline, which is environmental- friendly and economical. By combining BP neural network and PID control and using BP neural network self-learning ability for online parameter tuning, this method optimizes the parameters of PID controller and applies this to the Fcc gas flow control to achieve the control of the final product- heavy oil concentration. Finally, through MATLAB simulation, it is found that the PID control based on BP neural network has better controlling effect than traditional PID control.

Quality control process improvement of flexible printed circuit board by FMEA

NASA Astrophysics Data System (ADS)

Krasaephol, Siwaporn; Chutima, Parames

2018-02-01

This research focuses on the quality control process improvement of Flexible Printed Circuit Board (FPCB), centred around model 7-Flex, by using Failure Mode and Effect Analysis (FMEA) method to decrease proportion of defective finished goods that are found at the final inspection process. Due to a number of defective units that were found at the final inspection process, high scraps may be escaped to customers. The problem comes from poor quality control process which is not efficient enough to filter defective products from in-process because there is no In-Process Quality Control (IPQC) or sampling inspection in the process. Therefore, the quality control process has to be improved by setting inspection gates and IPCQs at critical processes in order to filter the defective products. The critical processes are analysed by the FMEA method. IPQC is used for detecting defective products and reducing chances of defective finished goods escaped to the customers. Reducing proportion of defective finished goods also decreases scrap cost because finished goods incur higher scrap cost than work in-process. Moreover, defective products that are found during process can reflect the abnormal processes; therefore, engineers and operators should timely solve the problems. Improved quality control was implemented for 7-Flex production lines from July 2017 to September 2017. The result shows decreasing of the average proportion of defective finished goods and the average of Customer Manufacturers Lot Reject Rate (%LRR of CMs) equal to 4.5% and 4.1% respectively. Furthermore, cost saving of this quality control process equals to 100K Baht.

75 FR 6597 - Determination to Approve Alternative Final Cover Request for the Lake County, MT Landfill...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-10

... layer, a 24-inch native sand layer, an 18-inch imported silt evapotranspiration layer, and a 6-inch... Quality Assurance & Control Plan'' for the closure project that specifies that testing will be performed... described in detail in the ``Construction Quality Assurance & Control Plan.'' II. EPA's Action A...

[Adaptation of the (18)FDG module for the preparation of a sodium fluoride [(18)F] injection solution in agreement with the United States (USP 32) and European Pharmacopeia (PhEur 6)].

PubMed

Martínez, T; Cordero, B; Medín, S; Sánchez Salmón, A

2011-01-01

To establish an automated procedure for the preparation of sodium fluoride (18)F injection using the resources available in our laboratory for the preparation of (18)FDG and to analyze the repercussion of the conditioning column of the fluoride ion entrapment on the characteristics of the final product. The sequence of an (18)FDG synthesis module prepared so that it traps the fluoride ion from the cyclotron in ion-exchange resin diluted with 0.9% sodium chloride. The final solution was dosified and sterilized in a final vial in an automatized dispensing module. Three different column conditioning protocols within the process were tested. Quality controls were run according to USP 32 and EurPh 6, adding control of ethanol levels of residual solvent and quality controls of the solution at 8 h post-preparation. Activation of the resin cartridges with ethanol and water was the chosen procedure, with fluoride ion trapping > 95% and pH around 7. Ethanol levels were < 5.000 ppm. Quality controls at 8 h indicated that the solution was in compliance with the USP 32 and EurPh 6 specifications. This is an easy, low-cost, reliable automated method for sodium fluoride preparation in PET facilities with existing equipment for (18)FDG synthesis and quality control. Copyright © 2010 Elsevier España, S.L. y SEMNIM. All rights reserved.

Maturity method demonstration : final report.

DOT National Transportation Integrated Search

2003-07-01

The concrete maturity method is a quality control/quality assurance tool that can be used to assist contractors and transportation officials in producing cost-efficient, durable concrete structures. This report documents the findings of an investigat...

Reference H Cycle 3 Stability, Control, and Flying Qualities Batch Assessments

NASA Technical Reports Server (NTRS)

Henderson, Dennis K.

1999-01-01

This work is an update of the assessment completed in February of 1996, when a preliminary assessment report was issued for the Cycle 2B simulation model. The primary purpose of the final assessment was to re-evaluate each assessment against the flight control system (FCS) requirements document using the updated model. Only a limited number of final assessments were completed due to the close proximity of the release of the Langley model and the assessment deliverable date. The assessment used the nonlinear Cycle 3 simulation model because it combines nonlinear aeroelastic (quasi-static) aerodynamic with hinge moment and rate limited control surface deflections. Both Configuration Aerodynamics (Task 32) and Flight Controls (Task 36) were funded in 1996 to conduct the final stability and control assessments of the unaugmented Reference H configuration in FY96. Because the two tasks had similar output requirements, the work was divided such that Flight Controls would be responsible for the implementation and checkout of the simulation model and Configuration Aerodynamics for writing Madab "script' files, conducting the batch assessments and writing the assessment report. Additionally, Flight Controls was to investigate control surface allocations schemes different from the baseline Reference H in an effort to fulfill flying qualities criteria.

78 FR 49925 - Revisions to California State Implementation Plan, Antelope Valley Air Quality Management...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-16

... California State Implementation Plan, Antelope Valley Air Quality Management District and Ventura County Air...: EPA is taking direct final action to approve revisions to the Antelope Valley Air Quality Air Management District (AVAQMD) and Ventura County Air Pollution Control District (VCAPCD) portions of the...

58th SOW Low-Dust Helicopter Landing Zone Final Environmental Assessment

DTIC Science & Technology

2012-11-01

Effects AQCR Air Quality Control Region BASH Bird/wildlife-Aircraft Strike Hazard CEQ Council on Environmental Quality CFR Code of Federal Regulations...force would continue to be applied to minimize risks to aircrews and the general population. No unacceptable hazards to military personnel, the public...and Final EA As a result of comments received on the Draft EA, Section 3.1.2, Global Climate Change, and Hazardous and Toxic Materials and Waste

76 FR 5277 - Revisions to the California State Implementation Plan, Santa Barbara Air Pollution Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-31

... the California State Implementation Plan, Santa Barbara Air Pollution Control District, Antelope Valley Air Quality Management District, Ventura County Air Pollution Control District and Placer County Air Pollution Control District AGENCY: Environmental Protection Agency (EPA). ACTION: Direct final...

Total Quality Management (TQM), an Overview

DTIC Science & Technology

1991-09-01

Quality Management (TQM). It discusses the reasons TQM is a current growth industry, what it is, and how one implements it. It describes the basic analytical tools, statistical process control, some advanced analytical tools, tools used by process improvement teams to enhance their own operations, and action plans for making improvements. The final sections discuss assessing quality efforts and measuring the quality to knowledge

Achieving Quality in the Navy Field Contracting System

DTIC Science & Technology

1986-12-01

they place on suppliers increase. Unless the supplier can satisfy the consumer , the consumer will go elsewhere for his/her needs. This reality caught...Quality products sell. Today’s consumers are willing to pay for quality so a company with a quality product is likely to control the market. Finally...the quality doctrine, but will provide a central point within the KFCS to address problems founc in improving quality. Training is another important

Effect on asphalt quality due to nighttime construction : final report.

DOT National Transportation Integrated Search

2017-06-01

The objectives of this project were to identify and analyze the nighttime paving traffic control standards in other states and compare the effects of daytime vs. nighttime paving on quality, safety, costs, and construction time. Surveys of various De...

Astronomical Instrumentation Systems Quality Management Planning: AISQMP

NASA Astrophysics Data System (ADS)

Goldbaum, Jesse

2017-06-01

The capability of small aperture astronomical instrumentation systems (AIS) to make meaningful scientific contributions has never been better. The purpose of AIS quality management planning (AISQMP) is to ensure the quality of these contributions such that they are both valid and reliable. The first step involved with AISQMP is to specify objective quality measures not just for the AIS final product, but also for the instrumentation used in its production. The next step is to set up a process to track these measures and control for any unwanted variation. The final step is continual effort applied to reducing variation and obtaining measured values near optimal theoretical performance. This paper provides an overview of AISQMP while focusing on objective quality measures applied to astronomical imaging systems.

Astronomical Instrumentation Systems Quality Management Planning: AISQMP (Abstract)

NASA Astrophysics Data System (ADS)

Goldbaum, J.

2017-12-01

(Abstract only) The capability of small aperture astronomical instrumentation systems (AIS) to make meaningful scientific contributions has never been better. The purpose of AIS quality management planning (AISQMP) is to ensure the quality of these contributions such that they are both valid and reliable. The first step involved with AISQMP is to specify objective quality measures not just for the AIS final product, but also for the instrumentation used in its production. The next step is to set up a process to track these measures and control for any unwanted variation. The final step is continual effort applied to reducing variation and obtaining measured values near optimal theoretical performance. This paper provides an overview of AISQMP while focusing on objective quality measures applied to astronomical imaging systems.

Revisiting the Procedures for the Vector Data Quality Assurance in Practice

NASA Astrophysics Data System (ADS)

Erdoğan, M.; Torun, A.; Boyacı, D.

2012-07-01

Immense use of topographical data in spatial data visualization, business GIS (Geographic Information Systems) solutions and applications, mobile and location-based services forced the topo-data providers to create standard, up-to-date and complete data sets in a sustainable frame. Data quality has been studied and researched for more than two decades. There have been un-countable numbers of references on its semantics, its conceptual logical and representations and many applications on spatial databases and GIS. However, there is a gap between research and practice in the sense of spatial data quality which increases the costs and decreases the efficiency of data production. Spatial data quality is well-known by academia and industry but usually in different context. The research on spatial data quality stated several issues having practical use such as descriptive information, metadata, fulfillment of spatial relationships among data, integrity measures, geometric constraints etc. The industry and data producers realize them in three stages; pre-, co- and post data capturing. The pre-data capturing stage covers semantic modelling, data definition, cataloguing, modelling, data dictionary and schema creation processes. The co-data capturing stage covers general rules of spatial relationships, data and model specific rules such as topologic and model building relationships, geometric threshold, data extraction guidelines, object-object, object-belonging class, object-non-belonging class, class-class relationships to be taken into account during data capturing. And post-data capturing stage covers specified QC (quality check) benchmarks and checking compliance to general and specific rules. The vector data quality criteria are different from the views of producers and users. But these criteria are generally driven by the needs, expectations and feedbacks of the users. This paper presents a practical method which closes the gap between theory and practice. Development of spatial data quality concepts into developments and application requires existence of conceptual, logical and most importantly physical existence of data model, rules and knowledge of realization in a form of geo-spatial data. The applicable metrics and thresholds are determined on this concrete base. This study discusses application of geo-spatial data quality issues and QA (quality assurance) and QC procedures in the topographic data production. Firstly we introduce MGCP (Multinational Geospatial Co-production Program) data profile of NATO (North Atlantic Treaty Organization) DFDD (DGIWG Feature Data Dictionary), the requirements of data owner, the view of data producers for both data capturing and QC and finally QA to fulfil user needs. Then, our practical and new approach which divides the quality into three phases is introduced. Finally, implementation of our approach to accomplish metrics, measures and thresholds of quality definitions is discussed. In this paper, especially geometry and semantics quality and quality control procedures that can be performed by the producers are discussed. Some applicable best-practices that we experienced on techniques of quality control, defining regulations that define the objectives and data production procedures are given in the final remarks. These quality control procedures should include the visual checks over the source data, captured vector data and printouts, some automatic checks that can be performed by software and some semi-automatic checks by the interaction with quality control personnel. Finally, these quality control procedures should ensure the geometric, semantic, attribution and metadata quality of vector data.

Improvement of Base and Soil Construction Quality by Using Intelligent Compaction Technology : Final Report.

DOT National Transportation Integrated Search

2017-08-01

Intelligent Compaction (IC) technique is a fast-developing technology for base and soil compaction quality control. Proof-rolling subgrades and bases using IC rollers upon completion of compaction can identify the less stiff spots and significantly i...

JV Task 94 - Air Quality V: Mercury, Trace Elements, SO3, and Particulate Matter Conference

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas A. Erickson

2007-01-31

This final report summarizes the planning, preparation, facilitation and production, and summary of the conference entitled 'Air Quality V: Mercury, Trace Elements, SO{sub 3}, and Particulate Matter,' held September 18-21, 2005, in Arlington, Virginia. The goal of the conference was to build on the discussions of the first four Air Quality Conferences, providing further opportunity for leading representatives of industry, government, research institutions, academia, and environmental organizations to discuss the key interrelationships between policy and science shaping near-term regulations and controls and to assist in moving forward on emerging issues that will lead to acceptable programs and policies to protectmore » human health, the environment, and economic growth. The conference was extremely timely, as it was the last large conference prior to publication of the U.S. Environmental Protection Agency's final regulations for mercury control from coal-fired utilities, and provided a forum to realistically assess the status of mercury controls in relation to the new regulations.« less

Space shuttle flying qualities and criteria assessment

NASA Technical Reports Server (NTRS)

Myers, T. T.; Johnston, D. E.; Mcruer, Duane T.

1987-01-01

Work accomplished under a series of study tasks for the Flying Qualities and Flight Control Systems Design Criteria Experiment (OFQ) of the Shuttle Orbiter Experiments Program (OEX) is summarized. The tasks involved review of applicability of existing flying quality and flight control system specification and criteria for the Shuttle; identification of potentially crucial flying quality deficiencies; dynamic modeling of the Shuttle Orbiter pilot/vehicle system in the terminal flight phases; devising a nonintrusive experimental program for extraction and identification of vehicle dynamics, pilot control strategy, and approach and landing performance metrics, and preparation of an OEX approach to produce a data archive and optimize use of the data to develop flying qualities for future space shuttle craft in general. Analytic modeling of the Orbiter's unconventional closed-loop dynamics in landing, modeling pilot control strategies, verification of vehicle dynamics and pilot control strategy from flight data, review of various existent or proposed aircraft flying quality parameters and criteria in comparison with the unique dynamic characteristics and control aspects of the Shuttle in landing; and finally a summary of conclusions and recommendations for developing flying quality criteria and design guides for future Shuttle craft.

ENVIRONMENTAL TECHNOLOGY VERIFICATION FOR AIR POLLUTION CONTROL TECHNOLOGIES: FINAL REPORT

EPA Science Inventory

The technical objective of the Environmental Technology Verification (ETV) Program's Air Pollution Control Technology (APCT) Center is to verify environmental technology performance by obtaining objective quality-assured data, thus providing potential purchasers and permitters wi...

Statistical quality control and quality assurance evaluation of structural & paving concrete : phase I final report.

DOT National Transportation Integrated Search

2001-08-01

This report discusses the variability associated with the production, construction, and testing of structural and paving concrete. The study evaluated data from over 900 projects constructed between 1992 and 1999, representing over 25,000 lots. The d...

Evaluation of Flying Qualities and Guidance Displays for an Advanced Tilt-Wing STOL Transport Aircraft in Final Approach and Landing

NASA Technical Reports Server (NTRS)

Frost, Chad R.; Franklin, James A.; Hardy, Gordon H.

2002-01-01

A piloted simulation was performed on the Vertical Motion Simulator at NASA Ames Research Center to evaluate flying qualities of a tilt-wing Short Take-Off and Landing (STOL) transport aircraft during final approach and landing. The experiment was conducted to assess the design s handling qualities, and to evaluate the use of flightpath-centered guidance for the precision approach and landing tasks required to perform STOL operations in instrument meteorological conditions, turbulence, and wind. Pilots rated the handling qualities to be satisfactory for all operations evaluated except those encountering extreme crosswinds and severe windshear; even in these difficult meteorological conditions, adequate handling qualities were maintained. The advanced flight control laws and guidance displays provided consistent performance and precision landings.

AutoLock: a semiautomated system for radiotherapy treatment plan quality control

PubMed Central

Lowe, Matthew; Hardy, Mark J.; Boylan, Christopher J.; Whitehurst, Philip; Rowbottom, Carl G.

2015-01-01

A semiautomated system for radiotherapy treatment plan quality control (QC), named AutoLock, is presented. AutoLock is designed to augment treatment plan QC by automatically checking aspects of treatment plans that are well suited to computational evaluation, whilst summarizing more subjective aspects in the form of a checklist. The treatment plan must pass all automated checks and all checklist items must be acknowledged by the planner as correct before the plan is finalized. Thus AutoLock uniquely integrates automated treatment plan QC, an electronic checklist, and plan finalization. In addition to reducing the potential for the propagation of errors, the integration of AutoLock into the plan finalization workflow has improved efficiency at our center. Detailed audit data are presented, demonstrating that the treatment plan QC rejection rate fell by around a third following the clinical introduction of AutoLock. PACS number: 87.55.Qr PMID:26103498

AutoLock: a semiautomated system for radiotherapy treatment plan quality control.

PubMed

Dewhurst, Joseph M; Lowe, Matthew; Hardy, Mark J; Boylan, Christopher J; Whitehurst, Philip; Rowbottom, Carl G

2015-05-08

A semiautomated system for radiotherapy treatment plan quality control (QC), named AutoLock, is presented. AutoLock is designed to augment treatment plan QC by automatically checking aspects of treatment plans that are well suited to computational evaluation, whilst summarizing more subjective aspects in the form of a checklist. The treatment plan must pass all automated checks and all checklist items must be acknowledged by the planner as correct before the plan is finalized. Thus AutoLock uniquely integrates automated treatment plan QC, an electronic checklist, and plan finalization. In addition to reducing the potential for the propagation of errors, the integration of AutoLock into the plan finalization workflow has improved efficiency at our center. Detailed audit data are presented, demonstrating that the treatment plan QC rejection rate fell by around a third following the clinical introduction of AutoLock.

Process-based quality for thermal spray via feedback control

NASA Astrophysics Data System (ADS)

Dykhuizen, R. C.; Neiser, R. A.

2006-09-01

Quality control of a thermal spray system manufacturing process is difficult due to the many input variables that need to be controlled. Great care must be taken to ensure that the process remains constant to obtain a consistent quality of the parts. Control is greatly complicated by the fact that measurement of particle velocities and temperatures is a noisy stochastic process. This article illustrates the application of quality control concepts to a wire flame spray process. A central feature of the real-time control system is an automatic feedback control scheme that provides fine adjustments to ensure that uncontrolled variations are accommodated. It is shown how the control vectors can be constructed from simple process maps to independently control particle velocity and temperature. This control scheme is shown to perform well in a real production environment. We also demonstrate that slight variations in the feed wire curvature can greatly influence the process. Finally, the geometry of the spray system and sensor must remain constant for the best reproducibility.

Contribution au developpement d'une methode de controle des procedes dans une usine de bouletage

NASA Astrophysics Data System (ADS)

Gosselin, Claude

This thesis, a collaborative effort between Ecole de technologie superieure and ArcelorMittal Company, presents the development of a methodology for monitoring and quality control of multivariable industrial production processes. This innovation research mandate was developed at ArcelorMittal Exploitation Miniere (AMEM) pellet plant in Port-Cartier (Quebec, Canada). With this undertaking, ArcelorMittal is striving to maintain its world class level of excellence and continues to pursue initiatives that can augment its competitive advantage worldwide. The plant's gravimetric classification process was retained as a prototype and development laboratory due to its effect on the company's competitiveness and its impact on subsequent steps leading to final production of iron oxide pellets. Concretely, the development of this expertise in process control and in situ monitoring will establish a firm basic knowledge in the fields of complex system physical modeling, data reconciliation, statistical observers, multivariate command and quality control using real-time monitoring of the desirability function. The hydraulic classifier is mathematically modeled. Using planned disturbances on the production line, an identification procedure was established to provide empirical estimations of the model's structural parameters. A new sampling campaign and a previously unpublished data collection and consolidation policy were implemented plant-wide. Access to these invaluable data sources has enabled the establishment of new thresholds that govern the production process and its control. Finally, as a substitute for the traditional quality control process, we have implemented a new strategy based on the use of the desirability function. Our innovation is not in using this Finally, as a substitute for the traditional quality control process, we have implemented a new strategy based on the use of the desirability function. Our innovation is not in using this function as an indicator of overall (economic) satisfaction in the production process, but rather in proposing it as an "observer" of the system's state. The first implementation steps have already demonstrated the method's feasibility as well as other numerous industrial impacts on production processes within the company. Namely, the emergence of the economical aspect as a strategic variable that assures better governance of production processes where quality variables present strategic issues.

[Quality control and assessment of qualitative interview in health care research].

PubMed

Xie, Yan-ming; Liao, Xing

2008-07-01

It is not finally concluded how to standardize the use of qualitative research in the world. Qualitative researchers disagree with each other about this issue. As we know, there have been a large number of articles written in different ways about qualitative research due to the "flexibility", one of its features. Qualitative research is quite different from quantitative research which is easy to control its quality and quality assessment. A series of criteria has been set up for quantitative research. However qualitative research needs to be improved in these aspects, in which qualitative interviews are mostly used at home and abroad at present. Hence, it becomes an important and urgent issue for qualitative researchers to standardly control and assess the quality of qualitative interview.

Development of a Premium Quality Plasma-derived IVIg (IQYMUNE®) Utilizing the Principles of Quality by Design-A Worked-through Case Study.

PubMed

Paolantonacci, Philippe; Appourchaux, Philippe; Claudel, Béatrice; Ollivier, Monique; Dennett, Richard; Siret, Laurent

2018-01-01

Polyvalent human normal immunoglobulins for intravenous use (IVIg), indicated for rare and often severe diseases, are complex plasma-derived protein preparations. A quality by design approach has been used to develop the Laboratoire Français du Fractionnement et des Biotechnologies new-generation IVIg, targeting a high level of purity to generate an enhanced safety profile while maintaining a high level of efficacy. A modular approach of quality by design was implemented consisting of five consecutive steps to cover all the stages from the product design to the final product control strategy.A well-defined target product profile was translated into 27 product quality attributes that formed the basis of the process design. In parallel, a product risk analysis was conducted and identified 19 critical quality attributes among the product quality attributes. Process risk analysis was carried out to establish the links between process parameters and critical quality attributes. Twelve critical steps were identified, and for each of these steps a risk mitigation plan was established.Among the different process risk mitigation exercises, five process robustness studies were conducted at qualified small scale with a design of experiment approach. For each process step, critical process parameters were identified and, for each critical process parameter, proven acceptable ranges were established. The quality risk management and risk mitigation outputs, including verification of proven acceptable ranges, were used to design the process verification exercise at industrial scale.Finally, the control strategy was established using a mix, or hybrid, of the traditional approach plus elements of the quality by design enhanced approach, as illustrated, to more robustly assign material and process controls and in order to securely meet product specifications.The advantages of this quality by design approach were improved process knowledge for industrial design and process validation and a clear justification of the process and product specifications as a basis for control strategy and future comparability exercises. © PDA, Inc. 2018.

Statistical methods for the quality control of steam cured concrete : final report.

DOT National Transportation Integrated Search

1971-01-01

Concrete strength test results from three prestressing plants utilizing steam curing were evaluated statistically in terms of the concrete as received and the effectiveness of the plants' steaming procedures. Control charts were prepared to show tren...

Application of the Critical Success Factor Methodology to DoD Organization.

DTIC Science & Technology

1984-09-01

high technology manufacturing, banking, airline, insurance, railway, and automobile . Sullen (6t22-25) lists the current CSFs of the 14 S automobile ...industry as image, quality dealer system, cost control, and meting energy standards. However, in 1981 the automobile CSFs included only styling, quality...bearing on current car purchases as well as future car buys. And finally cost control influenced the auto industry as a CSF, since profit per automobile had

[Study thought of pharmaceutical preparations quality standards by dynamic quality control technology].

PubMed

Yu, Dan-Hong; Mao, Chen-Mei; Lv, Cheng-Zhe; Jin, Hui-Zhen; Yao, Xin; Jia, Xiao-Bin

2014-07-01

Pharmaceutical preparations, particularly as a "secret recipe" of traditional Chinese medicine in medical institutions, are the product of China's medical and health industry, and they are also an important means of competing of different medical institutions. Although pharmaceutical preparations have advantages and characteristics than institutes for drug and pharmaceutical companies, the quality standards of pharmaceutical preparations in medical institutions has not reached the desired level over the years. As we all know, the quality of pharmaceutical preparations is important to ensure the efficacy, especially under the environment of people pay more sttention on drug safety and effectiveness and contry increase emphasis on the stste of pharmaceutical preparations. In view of this, we will improve the grade, stability, and clinical efficacy of pharmaceutical preparations by the advanced equipment, testing instruments and the process dynamic quality control technology. Finally, we hope we can provide new ideas for the quality control of pharmaceutical preparations.

Quality data collection and management technology of aerospace complex product assembly process

NASA Astrophysics Data System (ADS)

Weng, Gang; Liu, Jianhua; He, Yongxi; Zhuang, Cunbo

2017-04-01

Aiming at solving problems of difficult management and poor traceability for discrete assembly process quality data, a data collection and management method is proposed which take the assembly process and BOM as the core. Data collection method base on workflow technology, data model base on BOM and quality traceability of assembly process is included in the method. Finally, assembly process quality data management system is developed and effective control and management of quality information for complex product assembly process is realized.

78 FR 22840 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; State Board Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-17

... (SIP) revision submitted by the Delaware Department of Natural Resources and Environmental Control... as a direct final rule without prior proposal because EPA views this as a noncontroversial submittal... received will be addressed in a subsequent final rule based on this proposed rule. EPA will not institute a...

Simplification of a light-based model for estimating final internode length in greenhouse cucumber canopies.

PubMed

Kahlen, Katrin; Stützel, Hartmut

2011-10-01

Light quantity and quality affect internode lengths in cucumber (Cucumis sativus), whereby leaf area and the optical properties of the leaves mainly control light quality within a cucumber plant community. This modelling study aimed at providing a simple, non-destructive method to predict final internode lengths (FILs) using light quantity and leaf area data. Several simplifications of a light quantity and quality sensitive model for estimating FILs in cucumber have been tested. The direct simplifications substitute the term for the red : far-red (R : FR) ratios, by a term for (a) the leaf area index (LAI, m(2) m(-2)) or (b) partial LAI, the cumulative leaf area per m(2) ground, where leaf area per m(2) ground is accumulated from the top of each plant until a number, n, of leaves per plant is reached. The indirect simplifications estimate the input R : FR ratio based on partial leaf area and plant density. In all models, simulated FILs were in line with the measured FILs over various canopy architectures and light conditions, but the prediction quality varied. The indirect simplification based on leaf area of ten leaves revealed the best fit with measured data. Its prediction quality was even higher than of the original model. This study showed that for vertically trained cucumber plants, leaf area data can substitute local light quality data for estimating FIL data. In unstressed canopies, leaf area over the upper ten ranks seems to represent the feedback of the growing architecture on internode elongation with respect to light quality. This highlights the role of this domain of leaves as the primary source for the specific R : FR signal controlling the final length of an internode and could therefore guide future research on up-scaling local processes to the crop level.

Importance of good manufacturing practices in microbiological monitoring in processing human tissues for transplant.

PubMed

Pianigiani, Elisa; Ierardi, Francesca; Fimiani, Michele

2013-12-01

Skin allografts represent an important therapeutic resource in the treatment of severe skin loss. The risk associated with application of processed tissues in humans is very low, however, human material always carries the risk of disease transmission. To minimise the risk of contamination of grafts, processing is carried out in clean rooms where air quality is monitored. Procedures and quality control tests are performed to standardise the production process and to guarantee the final product for human use. Since we only validate and distribute aseptic tissues, we conducted a study to determine what type of quality controls for skin processing are the most suitable for detecting processing errors and intercurrent contamination, and for faithfully mapping the process without unduly increasing production costs. Two different methods for quality control were statistically compared using the Fisher exact test. On the basis of the current study we selected our quality control procedure based on pre- and post-processing tissue controls, operator and environmental controls. Evaluation of the predictability of our control methods showed that tissue control was the most reliable method of revealing microbial contamination of grafts. We obtained 100 % sensitivity by doubling tissue controls, while maintaining high specificity (77 %).

76 FR 72626 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-25

.... (See section 307(b)(2).) List of Subjects in 40 CFR part 52 Environmental protection, Air pollution... Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the Control of Volatile Organic... accordance with the requirements of the Clean Air Act (CAA). DATES: Effective Date: This final rule is...

ECOLOGICAL IMPACT OF INTEGRATED CHEMICAL AND BIOLOGICAL AQUATIC WEED CONTROL

EPA Science Inventory

This final report presents results of a four-year study of the ecological impacts of chemical, biological, and integrated methods of aquatic weed control. Biological and water quality changes occurred as abundance of macrophytic vegetation was altered by natural factors or manage...

Low bandwidth robust controllers for flight

NASA Technical Reports Server (NTRS)

Biezad, Daniel J.; Chou, Hwei-Lan

1992-01-01

During the final reporting period (Jun. - Dec. 1992), analyses of the longitudinal and lateral flying qualities were made for propulsive-only flight control (POFC) of a Boeing 720 aircraft model. Performance resulting from compensators developed using Quantitative Feedback Theory (QFT) is documented and analyzed. This report is a first draft of a thesis to be presented by graduate student Hwei-Lan Chou. The final thesis will be presented to NASA when it is completed later this year. The latest landing metrics related to bandwidth criteria and based on the Neal-Smith approach to flying qualities prediction were used in developing performance criteria for the controllers. The compensator designs were tested on the NASA simulator and exhibited adequate performance for piloted flight. There was no significant impact of QFT on performance of the propulsive-only flight controllers in either the longitudinal or lateral modes of flight. This was attributed to the physical limits of thrust available and the engine rate of response, both of whiih severely limited the available bandwidth of the closed-loop system.

Quality control of the RMS US flood model

NASA Astrophysics Data System (ADS)

Jankowfsky, Sonja; Hilberts, Arno; Mortgat, Chris; Li, Shuangcai; Rafique, Farhat; Rajesh, Edida; Xu, Na; Mei, Yi; Tillmanns, Stephan; Yang, Yang; Tian, Ye; Mathur, Prince; Kulkarni, Anand; Kumaresh, Bharadwaj Anna; Chaudhuri, Chiranjib; Saini, Vishal

2016-04-01

The RMS US flood model predicts the flood risk in the US with a 30 m resolution for different return periods. The model is designed for the insurance industry to estimate the cost of flood risk for a given location. Different statistical, hydrological and hydraulic models are combined to develop the flood maps for different return periods. A rainfall-runoff and routing model, calibrated with observed discharge data, is run with 10 000 years of stochastic simulated precipitation to create time series of discharge and surface runoff. The 100, 250 and 500 year events are extracted from these time series as forcing for a two-dimensional pluvial and fluvial inundation model. The coupling of all the different models which are run on the large area of the US implies a certain amount of uncertainty. Therefore, special attention is paid to the final quality control of the flood maps. First of all, a thorough quality analysis of the Digital Terrain model and the river network was done, as the final quality of the flood maps depends heavily on the DTM quality. Secondly, the simulated 100 year discharge in the major river network (600 000 km) is compared to the 100 year discharge derived using extreme value distribution of all USGS gauges with more than 20 years of peak values (around 11 000 gauges). Thirdly, for each gauge the modelled flood depth is compared to the depth derived from the USGS rating curves. Fourthly, the modelled flood depth is compared to the base flood elevation given in the FEMA flood maps. Fifthly, the flood extent is compared to the FEMA flood extent. Then, for historic events we compare flood extents and flood depths at given locations. Finally, all the data and spatial layers are uploaded on geoserver to facilitate the manual investigation of outliers. The feedback from the quality control is used to improve the model and estimate its uncertainty.

Research on control strategy based on fuzzy PR for grid-connected inverter

NASA Astrophysics Data System (ADS)

Zhang, Qian; Guan, Weiguo; Miao, Wen

2018-04-01

In the traditional PI controller, there is static error in tracking ac signals. To solve the problem, the control strategy of a fuzzy PR and the grid voltage feed-forward is proposed. The fuzzy PR controller is to eliminate the static error of the system. It also adjusts parameters of PR controller in real time, which avoids the defect of fixed parameter fixed. The grid voltage feed-forward control can ensure the quality of current and improve the system's anti-interference ability when the grid voltage is distorted. Finally, the simulation results show that the system can output grid current with good quality and also has good dynamic and steady state performance.

76 FR 52917 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-24

... Large Appliance and Metal Furniture Coatings AGENCY: Environmental Protection Agency (EPA). ACTION... Techniques Guidelines (CTG) standards for large appliance and metal furniture coatings. In the Final Rules...; Pennsylvania; Adoption of Control Techniques Guidelines for Large Appliance and Metal Furniture Coatings...

14 CFR 21.143 - Quality control data requirements; prime manufacturer.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., purchased items, and parts and assemblies produced by manufacturers' suppliers including methods used to... special manufacturing processes involved, the means used to control the processes, the final test... procedure for recording review board decisions and disposing of rejected parts; (5) An outline of a system...

TRMM Microwave Imager (TMI) Updates for Final Data Version Release

NASA Technical Reports Server (NTRS)

Kroodsma, Rachael A; Bilanow, Stephen; Ji, Yimin; McKague, Darren

2017-01-01

The Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI) dataset released by the Precipitation Processing System (PPS) will be updated to a final version within the next year. These updates are based on increased knowledge in recent years of radiometer calibration and sensor performance issues. In particular, the Global Precipitation Measurement (GPM) Microwave Imager (GMI) is used as a model for many of the TMI version updates. This paper discusses four aspects of the TMI data product that will be improved: spacecraft attitude, calibration and quality control, along-scan bias corrections, and sensor pointing accuracy. These updates will be incorporated into the final TMI data version, improving the quality of the data product and ensuring accurate geophysical parameters can be derived from TMI.

Quality Control of Structural MRI Images Applied Using FreeSurfer—A Hands-On Workflow to Rate Motion Artifacts

PubMed Central

Backhausen, Lea L.; Herting, Megan M.; Buse, Judith; Roessner, Veit; Smolka, Michael N.; Vetter, Nora C.

2016-01-01

In structural magnetic resonance imaging motion artifacts are common, especially when not scanning healthy young adults. It has been shown that motion affects the analysis with automated image-processing techniques (e.g., FreeSurfer). This can bias results. Several developmental and adult studies have found reduced volume and thickness of gray matter due to motion artifacts. Thus, quality control is necessary in order to ensure an acceptable level of quality and to define exclusion criteria of images (i.e., determine participants with most severe artifacts). However, information about the quality control workflow and image exclusion procedure is largely lacking in the current literature and the existing rating systems differ. Here, we propose a stringent workflow of quality control steps during and after acquisition of T1-weighted images, which enables researchers dealing with populations that are typically affected by motion artifacts to enhance data quality and maximize sample sizes. As an underlying aim we established a thorough quality control rating system for T1-weighted images and applied it to the analysis of developmental clinical data using the automated processing pipeline FreeSurfer. This hands-on workflow and quality control rating system will aid researchers in minimizing motion artifacts in the final data set, and therefore enhance the quality of structural magnetic resonance imaging studies. PMID:27999528

76 FR 10249 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Revisions To Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-24

... Container rule as an ozone control strategy from the Texas SIP for the Control of Ozone Air Pollution. In the submittal, Texas demonstrates that Federal portable fuel container standards promulgated by EPA in... Portable Fuel Container Regulations IV. What is the effect of this action? V. Final Action VI. Statutory...

A new hyperspectral imaging based device for quality control in plastic recycling

NASA Astrophysics Data System (ADS)

Bonifazi, G.; D'Agostini, M.; Dall'Ava, A.; Serranti, S.; Turioni, F.

2013-05-01

The quality control of contamination level in the recycled plastics stream has been identified as an important key factor for increasing the value of the recycled material by both plastic recycling and compounder industries. Existing quality control methods for the detection of both plastics and non-plastics contaminants in the plastic waste streams at different stages of the industrial process (e.g. feed, intermediate and final products) are currently based on the manual collection from the stream of a sample and on the subsequent off-line laboratory analyses. The results of such analyses are usually available after some hours, or sometimes even some days, after the material has been processed. The laboratory analyses are time-consuming and expensive (both in terms of equipment cost and their maintenance and of labour cost).Therefore, a fast on-line assessment to monitor the plastic waste feed streams and to characterize the composition of the different plastic products, is fundamental to increase the value of secondary plastics. The paper is finalized to describe and evaluate the development of an HSI-based device and of the related software architectures and processing algorithms for quality assessment of plastics in recycling plants, with particular reference to polyolefins (PO). NIR-HSI sensing devices coupled with multivariate data analysis methods was demonstrated as an objective, rapid and non-destructive technique that can be used for on-line quality and process control in the recycling process of POs. In particular, the adoption of the previous mentioned HD&SW integrated architectures can provide a solution to one of the major problems of the recycling industry, which is the lack of an accurate quality certification of materials obtained by recycling processes. These results could therefore assist in developing strategies to certify the composition of recycled PO products.

76 FR 67315 - Supplemental Nutrition Assistance Program: Quality Control Error Tolerance Threshold

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-01

...This direct final rule is amending the Quality Control (QC) review error threshold in our regulations from $25.00 to $50.00. The purpose for raising the QC error threshold is to make permanent the temporary threshold change that was required by the American Recovery and Reinvestment Act of 2008. This change does not have an impact on the public. The QC system measures the accuracy of the eligibility system for the Supplemental Nutrition Assistance Program (SNAP).

Benefits of an automated GLP final report preparation software solution.

PubMed

Elvebak, Larry E

2011-07-01

The final product of analytical laboratories performing US FDA-regulated (or GLP) method validation and bioanalysis studies is the final report. Although there are commercial-off-the-shelf (COTS) software/instrument systems available to laboratory managers to automate and manage almost every aspect of the instrumental and sample-handling processes of GLP studies, there are few software systems available to fully manage the GLP final report preparation process. This lack of appropriate COTS tools results in the implementation of rather Byzantine and manual processes to cobble together all the information needed to generate a GLP final report. The manual nature of these processes results in the need for several iterative quality control and quality assurance events to ensure data accuracy and report formatting. The industry is in need of a COTS solution that gives laboratory managers and study directors the ability to manage as many portions as possible of the GLP final report writing process and the ability to generate a GLP final report with the click of a button. This article describes the COTS software features needed to give laboratory managers and study directors such a solution.

76 FR 42161 - Notice of Final Federal Agency Actions on Proposed Highway in California

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-18

... Gilman Drive; installation of new ramp meters; and, construction of a bicycle path along I-5. The project... at http://www.dot.ca.gov/dist11/envir.htm . Pending Federal actions include: 1. Section 401 Water Quality Certification from the San Diego Regional Water Quality Control Board (RWQCB), under Section 401...

76 FR 2947 - Notice of Final Federal Agency Actions on Proposed Highway in California

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-18

...) from State Route 52 (SR-52) to La Jolla Village Drive. Two high occupancy vehicle (HOV) lanes (one in each direction) from La Jolla Village Drive to just north of Mira Mesa Boulevard (Blvd). The project.... Pending Federal actions include: 401 Water Quality Certification from the Regional Water Quality Control...

Development of the framework for a water quality monitoring system : controlling MoDOT's contribution to 303(d) listed streams in the state of Missouri, final report, February 2010.

DOT National Transportation Integrated Search

2010-02-01

By utilizing ArcGIS to quickly visualize the location of any impaired waterbody in relation to its projects/activities, MoDOT will : be able to allocate resources optimally. Additionally, the Water Quality Impact Database (WQID) will allow easy trans...

Quality control analysis : part V : review of data generated by statistical specifications on asphaltic concrete : final report.

DOT National Transportation Integrated Search

1975-12-01

The primary objective of this study was to review the data generated by projects governed by statistically oriented system of specifications for the control and acceptance of asphaltic concrete and to recommend any revisions that may be deemed necess...

Drug innovation, price controls, and parallel trade.

PubMed

Matteucci, Giorgio; Reverberi, Pierfrancesco

2016-12-21

We study the long-run welfare effects of parallel trade (PT) in pharmaceuticals. We develop a two-country model of PT with endogenous quality, where the pharmaceutical firm negotiates the price of the drug with the government in the foreign country. We show that, even though the foreign government does not consider global R&D costs, (the threat of) PT improves the quality of the drug as long as the foreign consumers' valuation of quality is high enough. We find that the firm's short-run profit may be higher when PT is allowed. Nonetheless, this is neither necessary nor sufficient for improving drug quality in the long run. We also show that improving drug quality is a sufficient condition for PT to increase global welfare. Finally, we show that, when PT is allowed, drug quality may be higher with than without price controls.

Sap flow sensors: construction, quality control and comparison.

PubMed

Davis, Tyler W; Kuo, Chen-Min; Liang, Xu; Yu, Pao-Shan

2012-01-01

This work provides a design for two types of sensors, based on the thermal dissipation and heat ratio methods of sap flow calculation, for moderate to large scale deployments for the purpose of monitoring tree transpiration. These designs include a procedure for making these sensors, a quality control method for the final products, and a complete list of components with vendors and pricing information. Both sensor designs were field tested alongside a commercial sap flow sensor to assess their performance and show the importance for quality controlling the sensor outputs. Results show that for roughly 2% of the cost of commercial sensors, self-made sap flow sensors can provide acceptable estimates of the sap flow measurements compared to the commercial sensors.

Regional Evaluation and Research Center for Head Start. Southern University, Annual Report, November 28, 1969. Final Report.

ERIC Educational Resources Information Center

Southern Univ. and Agricultural and Mechanical Coll., Baton Rouge, LA.

This final report of the third year of the Southern University-Tulane University Regional Head Start Evaluation and Research Center is a statement of activities engaged in since September 1968. Chapter I includes an introduction and description of the centers; Chapter II, evaluation guidelines, test battery, quality control, evaluation design and…

[Application of THz technology to nondestructive detection of agricultural product quality].

PubMed

Jiang, Yu-ying; Ge, Hong-yi; Lian, Fei-yu; Zhang, Yuan; Xia, Shan-hong

2014-08-01

With recent development of THz sources and detector, applications of THz radiation to nondestructive testing and quality control have expanded in many fields, such as agriculture, safety inspection and quality control, medicine, biochemistry, communication etc. Compared with other detection technique, being a new kind of technique, THz radiation has low energy, good perspectivity, and high signal-to-noise ratio, and thus can obtain physical, chemical and biological information. This paper first introduces the basic concept of THz radiation and the major properties, then gives an extensive review of recent research progress in detection of the quality of agricultural products via THz technique, analyzes the existing shortcomings of THz detection and discusses the outlook of potential application, finally proposes the new application of THz technique to detection of quality of stored grain.

REM desensitization as a new therapeutic method for post-traumatic stress disorder: a randomized controlled trial.

PubMed

Ahmadi, Khodabakhsh; Hazrati, Majid; Ahmadizadeh, Mohammadjavad; Noohi, Sima

2015-04-01

to evaluate potential efficacy of a new therapeutic approach in posttraumatic stress disorder in comparison with eye movement desensitization and reprocessing (EMDR), a standard treatment approach and controls. the study was designed using a randomized controlled trial methodology. Participants were recruited from military servicemen aged between 25 to 50 years who were admitting hospitals of Bushehr, Iran, with the final diagnosis of PTSD. Finally 33 male patients were devided into three subgroups: G1: EMDR; G2: REM Desensitization; and group 3: controls who received no therapy. Mississippi Scale for Posttraumatic Stress Disorder, Pittsburgh Sleep Quality Index (PSQI) and a 37 item death anxiety questionnaire were used for measures. multiple comparisons showed that intrusive thoughts were significantly more likely to improve with REM Desensitization versus EMDR (P=0.03), while depression was more responsive to EMDR (p=0.03). Among the Pittsburgh scale for the quality of sleep items, sleep quality (p=0.02), sleep duration (p=0.001), and total sleep quality score (p=0.002) were significantly more likely to improve in the REM Desensitization group. Change in the absolute death anxiety scores was not different between subgroups excepting EMDR versus control group (p=0.05). REM, desensitization, the new therapeutic approach to PTSD is a highly effective strategy, even more than EMDR, the standard treatment, in most of the evaluated subjects, with special emphasis on sleep symptoms, and also in the management of intrusive thoughts. Depression is the only factor in which, REM Desensitization was significantly less likely to represent a superior therapeutic effect than EMDR.

78 FR 12243 - Interim Final Determination To Stay and Defer Sanctions, Placer County Air Pollution Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-22

...EPA is making an interim final determination to stay the imposition of offset sanctions and to defer the imposition of highway sanctions based on a proposed approval of a revision to the Placer County Air Pollution Control District (PCAPCD) and Feather River Air Quality Management District (FRAQMD) portion of the California State Implementation Plan (SIP) published elsewhere in this Federal Register. The SIP revision concerns two permitting rules submitted by the PCAPCD and FRAQMD, respectively: Rule 502, New Source Review, and Rule 10.1, New Source Review.

The influence of personal qualities on performance and progression in a pre-registration nursing programme.

PubMed

Pitt, Victoria; Powis, David; Levett-Jones, Tracy; Hunter, Sharyn

2014-05-01

Research conducted primarily with psychology and medical students has highlighted that personal qualities play an important role in students' academic performance. In nursing there has been limited investigation of the relationship between personal qualities and performance. Yet, reports of student incivility and a lack of compassion have prompted appeals to integrate the assessment of personal qualities into pre-registration nursing student selection. Before this can be done research is needed to explore the influence of students' personal qualities on programme performance and progression. This study explores the relationships between students' personal qualities and their academic and clinical performance, behaviours and progression through a pre-registration nursing programme in Australia. This longitudinal descriptive correlational study was undertaken with a sample of Australian pre-registration nursing students (n=138). Students' personal qualities were assessed using three personal qualities assessment (PQA) instruments. Outcome measures included grades in nursing theory and clinical courses, yearly grade point average, final clinical competency, progression (completion), class attendance and levels of life event stress. Significant correlations were found between academic performance and PQA scores for self-control, resilience and traits of aloofness, confidence and involvement. Final clinical competence was predicted by confidence and self-control scores. Students with higher empathy had higher levels of life event stress in their first year and class attendance had a positive correlation with self-control. Completing the programme in three years was weakly predicted by the measure of resilience. No difference was noted between extreme or non-extreme scorers on the PQA scales with respect to performance or progression. This sample of students' personal qualities was found to influence their academic and clinical performance and their ability to complete a pre-registration programme in three years. However, further research is required with larger cohorts to confirm the use of personal qualities assessment during selection. © 2013.

Quality Assurance and Control Considerations in Environmental Measurements and Monitoring

NASA Astrophysics Data System (ADS)

Sedlet, Jacob

1982-06-01

Quality assurance and quality control have become accepted as essential parts of all environmental surveillance, measurements, and monitoring programs, both nuclear and non-nuclear. The same principles and details apply to each. It is primarily the final measurement technique that differs. As the desire and need to measure smaller amounts of pollutants with greater accuracy has increased, it has been recognized that quality assurance and control programs are cost-effective in achieving the expected results. Quality assurance (QA) consists of all the actions necessary to provide confidence in the results. Quality control (QC) is a part of QA, and consists of those actions and activities that permit the control of the individual steps in the environmental program. The distinction between the two terms is not always clearly defined, but a sharp division is not necessary. The essential principle of QA and QC is a commitment to high quality results. The essential components of a QA and QC program are a complete, written procedures manual for all parts of the environmental program, the use of standard or validated procedures, participation in applicable interlaboratory comparison or QA programs, replicate analysis and measurement, training of personnel, and a means of auditing or checking that the QA and QC programs are properly conducted. These components are discussed below in some detail.

Control by quality: proposition of a typology.

PubMed

Pujo, P; Pillet, M

The application of Quality tools and methods in industrial management has always had a fundamental impact on the control of production. It influences the behavior of the actors concerned, while introducing the necessary notions and formalizations, especially for production systems with little or no automation, which constitute a large part of the industrial activity. Several quality approaches are applied in the workshop and are implemented at the level of the control. In this paper, the authors present a typology of the various approaches that have successively influenced control, such as statistical process control, quality assurance, and continuous improvement. First the authors present a parallel between production control and quality organizational structure. They note the duality between control, which is aimed at increasing productivity, and quality, which aims to satisfy the needs of the customer. They also note the hierarchical organizational structure of these two systems of management with, at each level, the notion of a feedback loop. This notion is fundamental to any kind of decision making. The paper is organized around the operational, tactical, and strategic levels, by describing for each level the main methods and tools for control by quality. The overview of these tools and methods starts at the operational level, with the Statistical Process Control, the Taguchi technique, and the "six sigma" approach. On the tactical level, we find a quality system approach, with a documented description of the procedures introduced in the firm. The management system can refer here to Quality Assurance, Total Productive Maintenance, or Management by Total Quality. The formalization through procedures of the rules of decision governing the process control enhances the validity of these rules. This leads to the enhancement of their reliability and to their consolidation. All this counterbalances the human, intrinsically fluctuating, behavior of the control operators. Strategic control by quality is then detailed, and the two main approaches, the continuous improvement approach and the proactive improvement approach, are introduced. Finally, the authors observe that at each of the three levels, the continuous process improvement, which is a component of Total Quality, becomes an essential preoccupation for the control. Ultimately, the recursive utilization of the Deming cycle remains the best practice for the control by quality.

Ozone: Stage Two Vapor Recovery Rule and Guidance

EPA Pesticide Factsheets

This page includes the guidance document, fact sheet, memorandum, and final rule on removing Stage II Gasoline Vapor Control Programs from State Implementation Plans (SIP) for the Ozone National Ambient Air Quality Standards (NAAQS)

Pavement management system review : final report, October 2009.

DOT National Transportation Integrated Search

2009-10-01

The University of Alabama (UA) researchers worked with Alabama Department of Transportation (ALDOT) managers to investigate various mechanisms to provide quality control of data collection and interpretation for pavements, and to target the data resu...

Training and certification for construction inspectors : final report.

DOT National Transportation Integrated Search

2016-11-01

Construction inspectors are an important asset to the success of a Department of Transportation; they provide quality control for state- and federally funded transportation infrastructure projects. A majority of departments of transportation in the U...

Interaction between bacterial outer membrane proteins and periplasmic quality control factors: a kinetic partitioning mechanism.

PubMed

Wu, Si; Ge, Xi; Lv, Zhixin; Zhi, Zeyong; Chang, Zengyi; Zhao, Xin Sheng

2011-09-15

The OMPs (outer membrane proteins) of Gram-negative bacteria have to be translocated through the periplasmic space before reaching their final destination. The aqueous environment of the periplasmic space and high permeability of the outer membrane engender such a translocation process inevitably challenging. In Escherichia coli, although SurA, Skp and DegP have been identified to function in translocating OMPs across the periplasm, their precise roles and their relationship remain to be elucidated. In the present paper, by using fluorescence resonance energy transfer and single-molecule detection, we have studied the interaction between the OMP OmpC and these periplasmic quality control factors. The results of the present study reveal that the binding rate of OmpC to SurA or Skp is much faster than that to DegP, which may lead to sequential interaction between OMPs and different quality control factors. Such a kinetic partitioning mechanism for the chaperone-substrate interaction may be essential for the quality control of the biogenesis of OMPs.

78 FR 21545 - Revisions to the California State Implementation Plan, Antelope Valley Air Quality Management...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-11

...EPA is taking direct final action to approve revisions to the Antelope Valley Air Quality Management District (AVAQMD) and Monterey Bay Unified Air Pollution Control District (MBUAPCD) and Santa Barbara County Air Pollution Control District (SBCAPCD) portions of the California State Implementation Plan (SIP). Under authority of the Clean Air Act as amended in 1990 (CAA or the Act), we are approving local rules that address emission statements for AVAQMD, rule rescissions that addresses public records for MBUAPCD, and define terms for SBCAPCD.

Internal quality control: planning and implementation strategies.

PubMed

Westgard, James O

2003-11-01

The first essential in setting up internal quality control (IQC) of a test procedure in the clinical laboratory is to select the proper IQC procedure to implement, i.e. choosing the statistical criteria or control rules, and the number of control measurements, according to the quality required for the test and the observed performance of the method. Then the right IQC procedure must be properly implemented. This review focuses on strategies for planning and implementing IQC procedures in order to improve the quality of the IQC. A quantitative planning process is described that can be implemented with graphical tools such as power function or critical-error graphs and charts of operating specifications. Finally, a total QC strategy is formulated to minimize cost and maximize quality. A general strategy for IQC implementation is recommended that employs a three-stage design in which the first stage provides high error detection, the second stage low false rejection and the third stage prescribes the length of the analytical run, making use of an algorithm involving the average of normal patients' data.

Influence of dietary nano elemental selenium on growth performance, tissue selenium distribution, meat quality, and glutathione peroxidase activity in Guangxi Yellow chicken.

PubMed

Zhou, X; Wang, Y

2011-03-01

This experiment was designed to investigate the effect of feed supplementation with nano elemental Se (Nano-Se) on growth performance, tissue Se distribution, meat quality, and glutathione peroxidase (GSH-Px) activity in Guangxi Yellow chicken. Four treatments (control, T-1, T-2, and T-3 treatment groups) with 3 replicates of 30 chickens each were carried out. Diets for the control, T-1, T-2, and T-3 groups consisted of the basal diet supplemented with, respectively, 0.00, 0.10, 0.30, and 0.50 mg/kg of Nano-Se. Improved final BW, daily BW gain (DWG), feed conversion ratios, and survival rate (P < 0.05) were observed in the groups supplemented with Nano-Se as compared with the control groups after 90 d of feeding. The groups that received Nano-Se showed higher (P < 0.05) hepatic and muscle Se contents, drip loss percentage, inosine 5'-monophosphate content, and GSH-Px activities in the serum and liver than that did the control groups. For the T-2 and T-3 groups, a significant difference (P < 0.05) was observed in final BW, DWG, muscle Se content, breast drip loss, and GSH-Px activities in the serum and liver compared with the T-1 group. However, no significant differences were observed in final BW, DWG, and GSH-Px activities in the serum and liver between the T-2 and T-3 groups. It could be concluded from this study that supplementing diets with 0.30 mg/kg of Nano-Se for was effective in increasing the growth performance and feed conversion ratios of chickens, the Se content of tissues, and the quality of the meat.

C-A4-01: Computerized Clinical Decision Support During Drug Ordering for Long-term Care Residents With Renal Insufficiency

PubMed Central

Field, Terry S; Rochon, Paula; Lee, Monica; Gavendo, Linda; Baril, Joann L; Gurwitz, Jerry H

2010-01-01

Objective: To determine whether a computerized clinical decision support system (CDSS) providing patient specific recommendations in real- time improves the quality of prescribing for long-term care residents with renal insufficiency. Design: A randomized trial within the long-stay units of a large long-term care facility. Randomization was within blocks by unit type. Alerts related to medication prescribing for residents with renal insufficiency were displayed to prescribers in the intervention units and hidden but tracked in control units. Measurement: The proportions of final drug orders that were appropriate were compared between intervention and control units within alert categories: recommended medication doses; recommended administration frequencies; recommendations to avoid the drug; 4) warnings of missing information. Results: The rates of alerts were nearly equal in the intervention and control units: 2.5 per 1000 resident days in the intervention units and 2.4 in the control units. The proportions of dose alerts for which the final drug orders were appropriate were similar between the intervention and control units (relative risk 0.95, 95% confidence interval 0.83, 1.1). For the remaining alert categories significantly higher proportions of final drug orders were appropriate in the intervention units: relative risk 2.4 for maximum frequency (1.4, 4.4); 2.6 for drugs that should be avoided (1.4, 5.0); and 1.8 for alerts to acquire missing information (1.1, 3.4). Overall, final drug orders were appropriate significantly more often than a relative risk 1.2 (1.0, 1.4). By tracking personnel time and expenditures, we estimated the cost of developing the CDSS as $48,668.57. Drug costs saved during the 12 months of the trial are estimated at $2,137. Conclusion: Clinical decision support for physicians prescribing medications for long-term care residents with renal insufficiency can improve the quality of prescribing decisions. However, patient well-being and quality of care rather than the business case related to cost savings are likely to be the key drivers for adoption of this HIT application.

78 FR 58460 - Revision of Air Quality Implementation Plan; California; Placer County Air Pollution Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-24

...EPA is finalizing a limited approval and limited disapproval of two permitting rules submitted by California as a revision to the Placer County Air Pollution Control District (PCAPCD) and Feather River Air Quality Management District (FRAQMD) portion of the California State Implementation Plan (SIP). These revisions were proposed in the Federal Register on February 22, 2013 and concern construction and modification of stationary sources of air pollution within each District. We are approving local rules that regulate these emission sources under the Clean Air Act as amended in 1990 (CAA). Final approval of these rules makes the rules federally enforceable and corrects program deficiencies identified in a previous EPA rulemaking (76 FR 44809, July 27, 2011). EPA is also making a technical amendment to the Code of Federal Regulations (CFR) to reflect this previous rulemaking, which removed an obsolete provision from the California SIP.

Analysis of aircraft longitudinal handling qualities

NASA Technical Reports Server (NTRS)

Hess, R. A.

1981-01-01

The optimal control model (OCM) of the human pilot is applied to the study of aircraft handling qualities. Attention is focused primarily on longitudinal tasks. The modeling technique differs from previous applications of the OCM in that considerable effort is expended in simplifying the pilot/vehicle analysis. After briefly reviewing the OCM, a technique for modeling the pilot controlling higher order systems is introduced. Following this, a simple criterion for determining the susceptibility of an aircraft to pilot induced oscillations (PIO) is formulated. Finally, a model-based metric for pilot rating prediction is discussed. The resulting modeling procedure provides a relatively simple, yet unified approach to the study of a variety of handling qualities problems.

Prediction of aircraft handling qualities using analytical models of the human pilot

NASA Technical Reports Server (NTRS)

Hess, R. A.

1982-01-01

The optimal control model (OCM) of the human pilot is applied to the study of aircraft handling qualities. Attention is focused primarily on longitudinal tasks. The modeling technique differs from previous applications of the OCM in that considerable effort is expended in simplifying the pilot/vehicle analysis. After briefly reviewing the OCM, a technique for modeling the pilot controlling higher order systems is introduced. Following this, a simple criterion for determining the susceptibility of an aircraft to pilot-induced oscillations (PIO) is formulated. Finally, a model-based metric for pilot rating prediction is discussed. The resulting modeling procedure provides a relatively simple, yet unified approach to the study of a variety of handling qualities problems.

Prediction of aircraft handling qualities using analytical models of the human pilot

NASA Technical Reports Server (NTRS)

Hess, R. A.

1982-01-01

The optimal control model (OCM) of the human pilot is applied to the study of aircraft handling qualities. Attention is focused primarily on longitudinal tasks. The modeling technique differs from previous applications of the OCM in that considerable effort is expended in simplifying the pilot/vehicle analysis. After briefly reviewing the OCM, a technique for modeling the pilot controlling higher order systems is introduced. Following this, a simple criterion for determining the susceptibility of an aircraft to pilot induced oscillations is formulated. Finally, a model based metric for pilot rating prediction is discussed. The resulting modeling procedure provides a relatively simple, yet unified approach to the study of a variety of handling qualities problems.

A pilot modeling technique for handling-qualities research

NASA Technical Reports Server (NTRS)

Hess, R. A.

1980-01-01

A brief survey of the more dominant analysis techniques used in closed-loop handling-qualities research is presented. These techniques are shown to rely on so-called classical and modern analytical models of the human pilot which have their foundation in the analysis and design principles of feedback control. The optimal control model of the human pilot is discussed in some detail and a novel approach to the a priori selection of pertinent model parameters is discussed. Frequency domain and tracking performance data from 10 pilot-in-the-loop simulation experiments involving 3 different tasks are used to demonstrate the parameter selection technique. Finally, the utility of this modeling approach in handling-qualities research is discussed.

Low-quality birds do not display high-quality signals: The cysteine-pheomelanin mechanism of honesty

PubMed Central

Galván, Ismael; Wakamatsu, Kazumasa; Camarero, Pablo R; Mateo, Rafael; Alonso-Alvarez, Carlos

2015-01-01

The mechanisms that make that the costs of producing high-quality signals are unaffordable to low-quality signalers are a current issue in animal communication. The size of the melanin-based bib of male house sparrows Passer domesticus honestly signals quality. We induced the development of new bibs while treating males with buthionine-sulfoximine (BSO), a substance that depletes the levels of the antioxidant glutathione (GSH) and the amino acid cysteine, two elements that switch melanogenesis from eumelanin to pheomelanin. Final bib size is negatively related to pheomelanin levels in the bib feathers. BSO reduced cysteine and GSH levels in all birds, but improved phenotypes (bibs larger than controls) were only expressed by high-quality birds (BSO birds with largest bibs initially). Negative associations between final bib size and cysteine levels in erythrocytes, and between pheomelanin and cysteine levels, were observed in high-quality birds only. These findings suggest that a mechanism uncoupling pheomelanin and cysteine levels may have evolved in low-quality birds to avoid producing bibs of size not corresponding to their quality and greater relative costs. Indeed, greater oxidative stress in cells was not observed in low-quality birds. This may represent the first mechanism maintaining signal honesty without producing greater relative costs on low-quality signalers. PMID:25330349

Near-infrared Spectroscopy in the Brewing Industry.

PubMed

Sileoni, Valeria; Marconi, Ombretta; Perretti, Giuseppe

2015-01-01

This article offers an exhaustive description of the use of Near-Infrared (NIR) Spectroscopy in the brewing industry. This technique is widely used for quality control testing of raw materials, intermediates, and finished products, as well as process monitoring during malting and brewing. In particular, most of the reviewed works focus on the assessment of barley properties, aimed at quickly selecting the best barley varieties in order to produce a high-quality malt leading to high-quality beer. Various works concerning the use of NIR in the evaluation of raw materials, such as barley, malt, hop, and yeast, are also summarized here. The implementation of NIR sensors for the control of malting and brewing processes is also highlighted, as well as the use of NIR for quality assessment of the final product.

Drop-on-Demand System for Manufacturing of Melt-based Solid Oral Dosage: Effect of Critical Process Parameters on Product Quality.

PubMed

Içten, Elçin; Giridhar, Arun; Nagy, Zoltan K; Reklaitis, Gintaras V

2016-04-01

The features of a drop-on-demand-based system developed for the manufacture of melt-based pharmaceuticals have been previously reported. In this paper, a supervisory control system, which is designed to ensure reproducible production of high quality of melt-based solid oral dosages, is presented. This control system enables the production of individual dosage forms with the desired critical quality attributes: amount of active ingredient and drug morphology by monitoring and controlling critical process parameters, such as drop size and product and process temperatures. The effects of these process parameters on the final product quality are investigated, and the properties of the produced dosage forms characterized using various techniques, such as Raman spectroscopy, optical microscopy, and dissolution testing. A crystallization temperature control strategy, including controlled temperature cycles, is presented to tailor the crystallization behavior of drug deposits and to achieve consistent drug morphology. This control strategy can be used to achieve the desired bioavailability of the drug by mitigating variations in the dissolution profiles. The supervisor control strategy enables the application of the drop-on-demand system to the production of individualized dosage required for personalized drug regimens.

Final Environmental Assessment (EA), Long-Term Integrated Management of Mission-Generated Solid Waste, Edwards Air Force Base, California

DTIC Science & Technology

2016-11-28

infrastructure typically include energy, water, wastewater, electricity, natural gas , liquid fuel distribution systems, communication lines (e.g...with state off-road regulations would further reduce air quality and greenhouse gas emissions. Cultural Resources. The waste footprint as well as...maintenance of the prescriptive final cover and erosion control, landfill gas monitoring and well maintenance, groundwater monitoring and well maintenance

Gravity packaging final waste recovery based on gravity separation and chemical imaging control.

PubMed

Bonifazi, Giuseppe; Serranti, Silvia; Potenza, Fabio; Luciani, Valentina; Di Maio, Francesco

2017-02-01

Plastic polymers are characterized by a high calorific value. Post-consumer plastic waste can be thus considered, in many cases, as a typical secondary solid fuels according to the European Commission directive on End of Waste (EoW). In Europe the practice of incineration is considered one of the solutions for waste disposal waste, for energy recovery and, as a consequence, for the reduction of waste sent to landfill. A full characterization of these products represents the first step to profitably and correctly utilize them. Several techniques have been investigated in this paper in order to separate and characterize post-consumer plastic packaging waste fulfilling the previous goals, that is: gravity separation (i.e. Reflux Classifier), FT-IR spectroscopy, NIR HyperSpectralImaging (HSI) based techniques and calorimetric test. The study demonstrated as the proposed separation technique and the HyperSpectral NIR Imaging approach allow to separate and recognize the different polymers (i.e. PolyVinyl Chloride (PVC), PolyStyrene (PS), PolyEthylene (PE), PoliEtilene Tereftalato (PET), PolyPropylene (PP)) in order to maximize the removal of the PVC fraction from plastic waste and to perform the full quality control of the resulting products, can be profitably utilized to set up analytical/control strategies finalized to obtain a low content of PVC in the final Solid Recovered Fuel (SRF), thus enhancing SRF quality, increasing its value and reducing the "final waste". Copyright © 2016 Elsevier Ltd. All rights reserved.

Final Range Wide Environmental Impact Statement

DTIC Science & Technology

2001-07-01

military presence at YPG protects natural resources by limiting access and activities, preventing or mitigating many impacts. The military presence in the...Pollution Prevention Plan; and Spill Prevention , Control and Countermeasures Plan (SPCCP). Environmental programs are responsible for...Act (CAA), PL 88-206 as amended, establishes National Ambient Air Quality Standards (NAAQS) for the control of criteria air pollutants to prevent

A case study: application of statistical process control tool for determining process capability and sigma level.

PubMed

Chopra, Vikram; Bairagi, Mukesh; Trivedi, P; Nagar, Mona

2012-01-01

Statistical process control is the application of statistical methods to the measurement and analysis of variation process. Various regulatory authorities such as Validation Guidance for Industry (2011), International Conference on Harmonisation ICH Q10 (2009), the Health Canada guidelines (2009), Health Science Authority, Singapore: Guidance for Product Quality Review (2008), and International Organization for Standardization ISO-9000:2005 provide regulatory support for the application of statistical process control for better process control and understanding. In this study risk assessments, normal probability distributions, control charts, and capability charts are employed for selection of critical quality attributes, determination of normal probability distribution, statistical stability, and capability of production processes, respectively. The objective of this study is to determine tablet production process quality in the form of sigma process capability. By interpreting data and graph trends, forecasting of critical quality attributes, sigma process capability, and stability of process were studied. The overall study contributes to an assessment of process at the sigma level with respect to out-of-specification attributes produced. Finally, the study will point to an area where the application of quality improvement and quality risk assessment principles for achievement of six sigma-capable processes is possible. Statistical process control is the most advantageous tool for determination of the quality of any production process. This tool is new for the pharmaceutical tablet production process. In the case of pharmaceutical tablet production processes, the quality control parameters act as quality assessment parameters. Application of risk assessment provides selection of critical quality attributes among quality control parameters. Sequential application of normality distributions, control charts, and capability analyses provides a valid statistical process control study on process. Interpretation of such a study provides information about stability, process variability, changing of trends, and quantification of process ability against defective production. Comparative evaluation of critical quality attributes by Pareto charts provides the least capable and most variable process that is liable for improvement. Statistical process control thus proves to be an important tool for six sigma-capable process development and continuous quality improvement.

Importance of implementing an analytical quality control system in a core laboratory.

PubMed

Marques-Garcia, F; Garcia-Codesal, M F; Caro-Narros, M R; Contreras-SanFeliciano, T

2015-01-01

The aim of the clinical laboratory is to provide useful information for screening, diagnosis and monitoring of disease. The laboratory should ensure the quality of extra-analytical and analytical process, based on set criteria. To do this, it develops and implements a system of internal quality control, designed to detect errors, and compare its data with other laboratories, through external quality control. In this way it has a tool to detect the fulfillment of the objectives set, and in case of errors, allowing corrective actions to be made, and ensure the reliability of the results. This article sets out to describe the design and implementation of an internal quality control protocol, as well as its periodical assessment intervals (6 months) to determine compliance with pre-determined specifications (Stockholm Consensus(1)). A total of 40 biochemical and 15 immunochemical methods were evaluated using three different control materials. Next, a standard operation procedure was planned to develop a system of internal quality control that included calculating the error of the analytical process, setting quality specifications, and verifying compliance. The quality control data were then statistically depicted as means, standard deviations, and coefficients of variation, as well as systematic, random, and total errors. The quality specifications were then fixed and the operational rules to apply in the analytical process were calculated. Finally, our data were compared with those of other laboratories through an external quality assurance program. The development of an analytical quality control system is a highly structured process. This should be designed to detect errors that compromise the stability of the analytical process. The laboratory should review its quality indicators, systematic, random and total error at regular intervals, in order to ensure that they are meeting pre-determined specifications, and if not, apply the appropriate corrective actions. Copyright © 2015 SECA. Published by Elsevier Espana. All rights reserved.

75 FR 6337 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Control of Carbon...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-09

... Oxygen Furnaces AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule. SUMMARY: EPA... basic oxygen furnaces (BOFs) at steel mills with a new CO standard for BOFs at steel mills. In the Final...

Tumorigenicity assessment of human cell-processed therapeutic products.

PubMed

Yasuda, Satoshi; Sato, Yoji

2015-09-01

Human pluripotent stem cells (hPSCs) are expected to be sources of various cell types used for cell therapy, although hPSCs are intrinsically tumorigenic and form teratomas in immunodeficient animals after transplant. Despite the urgent need, no detailed guideline for the assessment of tumorigenicity of human cell-processed therapeutic products (hCTPs) has been issued. Here we describe our consideration on tumorigenicity and related tests of hCTPs. The purposes of those tests for hPSC-based products are classified into three categories: 1) quality control of raw materials; 2) quality control of intermediate/final products; and 3) safety assessment of final products. Appropriate types of tests need to be selected, taking the purpose(s) into consideration. In contrast, human somatic (and somatic stem) cells are believed to have little tumorigenicity. Therefore, GMP-compliant quality control is essential to avoid contamination of somatic cell-derived products with tumorigenic cells. Compared with in vivo tumorigenicity tests, in vitro cell proliferation assays may be more useful and reasonable for detecting immortalized cells that have a growth advantage in somatic cell-based products. The results obtained from tumorigenicity and related tests for hCTPs should meet the criteria for decisions on product development, manufacturing processes, and clinical applications. Copyright © 2015.

pcr: an R package for quality assessment, analysis and testing of qPCR data

PubMed Central

Ahmed, Mahmoud

2018-01-01

Background Real-time quantitative PCR (qPCR) is a broadly used technique in the biomedical research. Currently, few different analysis models are used to determine the quality of data and to quantify the mRNA level across the experimental conditions. Methods We developed an R package to implement methods for quality assessment, analysis and testing qPCR data for statistical significance. Double Delta CT and standard curve models were implemented to quantify the relative expression of target genes from CT in standard qPCR control-group experiments. In addition, calculation of amplification efficiency and curves from serial dilution qPCR experiments are used to assess the quality of the data. Finally, two-group testing and linear models were used to test for significance of the difference in expression control groups and conditions of interest. Results Using two datasets from qPCR experiments, we applied different quality assessment, analysis and statistical testing in the pcr package and compared the results to the original published articles. The final relative expression values from the different models, as well as the intermediary outputs, were checked against the expected results in the original papers and were found to be accurate and reliable. Conclusion The pcr package provides an intuitive and unified interface for its main functions to allow biologist to perform all necessary steps of qPCR analysis and produce graphs in a uniform way. PMID:29576953

In-situ quality monitoring during laser brazing

NASA Astrophysics Data System (ADS)

Ungers, Michael; Fecker, Daniel; Frank, Sascha; Donst, Dmitri; Märgner, Volker; Abels, Peter; Kaierle, Stefan

Laser brazing of zinc coated steel is a widely established manufacturing process in the automotive sector, where high quality requirements must be fulfilled. The strength, impermeablitiy and surface appearance of the joint are particularly important for judging its quality. The development of an on-line quality control system is highly desired by the industry. This paper presents recent works on the development of such a system, which consists of two cameras operating in different spectral ranges. For the evaluation of the system, seam imperfections are created artificially during experiments. Finally image processing algorithms for monitoring process parameters based the captured images are presented.

A tutorial for developing a topical cream formulation based on the Quality by Design approach.

PubMed

Simões, Ana; Veiga, Francisco; Vitorino, Carla; Figueiras, Ana

2018-06-20

The pharmaceutical industry has entered in a new era, as there is a growing interest in increasing the quality standards of dosage forms, through the implementation of more structured development and manufacturing approaches. For many decades, the manufacturing of drug products was controlled by a regulatory framework to guarantee the quality of the final product through a fixed process and exhaustive testing. Limitations related to the Quality by Test (QbT) system have been widely acknowledged. The emergence of Quality by Design (QbD) as a systematic and risk-based approach introduced a new quality concept based on a good understanding of how raw materials and process parameters influence the final quality profile. Although the QbD system has been recognized as a revolutionary approach to product development and manufacturing, its full implementation in the pharmaceutical field is still limited. This is particularly evident in the case of semisolid complex formulation development. The present review aims at establishing a practical QbD framework to describe all stages comprised in the pharmaceutical development of a conventional cream in a comprehensible manner. Copyright © 2018. Published by Elsevier Inc.

Framework for establishing records control in hospitals as an ISO 9001 requirement.

PubMed

Al-Qatawneh, Lina

2017-02-13

Purpose The purpose of this paper is to present the process followed to control records in a Jordanian private community hospital as an ISO 9001:2008 standard requirement. Design/methodology/approach Under the hospital quality council's supervision, the quality management and development office staff were responsible for designing, planning and implementing the quality management system (QMS) using the ISO 9001:2008 standard. A policy for records control was established. An action plan for establishing the records control was developed and implemented. On completion, a coding system for records was specified to be used by hospital staff. Finally, an internal audit was performed to verify conformity to the ISO 9001:2008 standard requirements. Findings Successful certification by a neutral body ascertained that the hospital's QMS conformed to the ISO 9001:2008 requirements. A framework was developed that describes the records controlling process, which can be used by staff in any healthcare organization wanting to achieve ISO 9001:2008 accreditation. Originality/value Given the increased interest among healthcare organizations to achieve the ISO 9001 certification, the proposed framework for establishing records control is developed and is expected to be a valuable management tool to improve and sustain healthcare quality.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sailer, S.J.

This Quality Assurance Project Plan (QAPJP) specifies the quality of data necessary and the characterization techniques employed at the Idaho National Engineering Laboratory (INEL) to meet the objectives of the Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Transuranic Waste Characterization Quality Assurance Program Plan (QAPP) requirements. This QAPJP is written to conform with the requirements and guidelines specified in the QAPP and the associated documents referenced in the QAPP. This QAPJP is one of a set of five interrelated QAPjPs that describe the INEL Transuranic Waste Characterization Program (TWCP). Each of the five facilities participating in the TWCPmore » has a QAPJP that describes the activities applicable to that particular facility. This QAPJP describes the roles and responsibilities of the Idaho Chemical Processing Plant (ICPP) Analytical Chemistry Laboratory (ACL) in the TWCP. Data quality objectives and quality assurance objectives are explained. Sample analysis procedures and associated quality assurance measures are also addressed; these include: sample chain of custody; data validation; usability and reporting; documentation and records; audits and 0385 assessments; laboratory QC samples; and instrument testing, inspection, maintenance and calibration. Finally, administrative quality control measures, such as document control, control of nonconformances, variances and QA status reporting are described.« less

Application of the quality by design approach to the drug substance manufacturing process of an Fc fusion protein: towards a global multi-step design space.

PubMed

Eon-duval, Alex; Valax, Pascal; Solacroup, Thomas; Broly, Hervé; Gleixner, Ralf; Strat, Claire L E; Sutter, James

2012-10-01

The article describes how Quality by Design principles can be applied to the drug substance manufacturing process of an Fc fusion protein. First, the quality attributes of the product were evaluated for their potential impact on safety and efficacy using risk management tools. Similarly, process parameters that have a potential impact on critical quality attributes (CQAs) were also identified through a risk assessment. Critical process parameters were then evaluated for their impact on CQAs, individually and in interaction with each other, using multivariate design of experiment techniques during the process characterisation phase. The global multi-step Design Space, defining operational limits for the entire drug substance manufacturing process so as to ensure that the drug substance quality targets are met, was devised using predictive statistical models developed during the characterisation study. The validity of the global multi-step Design Space was then confirmed by performing the entire process, from cell bank thawing to final drug substance, at its limits during the robustness study: the quality of the final drug substance produced under different conditions was verified against predefined targets. An adaptive strategy was devised whereby the Design Space can be adjusted to the quality of the input material to ensure reliable drug substance quality. Finally, all the data obtained during the process described above, together with data generated during additional validation studies as well as manufacturing data, were used to define the control strategy for the drug substance manufacturing process using a risk assessment methodology. Copyright © 2012 Wiley-Liss, Inc.

7 CFR 622.2 - Scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., water quality management, ground water supply, agricultural pollution control, and other water management. (d) After a final plan for works of improvement is agreed upon between NRCS and the sponsors and... proper utilization of land, flood prevention, agricultural water management including irrigation and...

Evaluation of Louisiana's statistically based quality control and acceptance specifications for asphaltic concrete : final report.

DOT National Transportation Integrated Search

1998-09-01

In 1971, the Louisiana Department of Transportation and Development initiated a statistically based specification system for asphaltic concrete using historically generated data. A Materials Test Data (MATT) reporting system was also started to archi...

Development of Medical Technology for Contingency Response to Marrow Toxic Agents

DTIC Science & Technology

2012-03-31

Development of Medical Technology for Contingency Response to Marrow Toxic Agents - Final Performance/Technical Report for March 01, 2010 to February 28...Development of Medical Technology for Contingency Response To Marrow Toxic Agents FINAL REPORT March 1, 2010 – March 31, 2012 National...Buccal Swabs 38 IIB.1.5 Enhancing HLA Data for Selected Donors 43 IIB.1.6 Maintain a Quality Control Program 46 IIB.2.1 Collection of Primary Data

The NCS code of practice for the quality assurance and control for volumetric modulated arc therapy

NASA Astrophysics Data System (ADS)

Mans, Anton; Schuring, Danny; Arends, Mark P.; Vugts, Cornelia A. J. M.; Wolthaus, Jochem W. H.; Lotz, Heidi T.; Admiraal, Marjan; Louwe, Rob J. W.; Öllers, Michel C.; van de Kamer, Jeroen B.

2016-10-01

In 2010, the NCS (Netherlands Commission on Radiation Dosimetry) installed a subcommittee to develop guidelines for quality assurance and control for volumetric modulated arc therapy (VMAT) treatments. The report (published in 2015) has been written by Dutch medical physicists and has therefore, inevitably, a Dutch focus. This paper is a condensed version of these guidelines, the full report in English is freely available from the NCS website www.radiationdosimetry.org. After describing the transition from IMRT to VMAT, the paper addresses machine quality assurance (QA) and treatment planning system (TPS) commissioning for VMAT. The final section discusses patient specific QA issues such as the use of class solutions, measurement devices and dose evaluation methods.

A Review of Control Strategy of the Large-scale of Electric Vehicles Charging and Discharging Behavior

NASA Astrophysics Data System (ADS)

Kong, Lingyu; Han, Jiming; Xiong, Wenting; Wang, Hao; Shen, Yaqi; Li, Ying

2017-05-01

Large scale access of electric vehicles will bring huge challenges to the safe operation of the power grid, and it’s important to control the charging and discharging of the electric vehicle. First of all, from the electric quality and network loss, this paper points out the influence on the grid caused by electric vehicle charging behaviour. Besides, control strategy of electric vehicle charging and discharging has carried on the induction and the summary from the direct and indirect control. Direct control strategy means control the electric charging behaviour by controlling its electric vehicle charging and discharging power while the indirect control strategy by means of controlling the price of charging and discharging. Finally, for the convenience of the reader, this paper also proposed a complete idea of the research methods about how to study the control strategy, taking the adaptability and possibility of failure of electric vehicle control strategy into consideration. Finally, suggestions on the key areas for future research are put up.

Comparative mass spectrometry & nuclear magnetic resonance metabolomic approaches for nutraceuticals quality control analysis: a brief review.

PubMed

Farag, Mohamed A

2014-01-01

The number of botanical dietary supplements in the market has recently increased primarily due to increased health awareness. Standardization and quality control of the constituents of these plant extracts is an important topic, particularly when such ingredients are used long term as dietary supplements, or in cases where higher doses are marketed as drugs. The development of fast, comprehensive, and effective untargeted analytical methods for plant extracts is of high interest. Nuclear magnetic resonance spectroscopy and mass spectrometry are the most informative tools, each of which enables high-throughput and global analysis of hundreds of metabolites in a single step. Although only one of the two techniques is utilized in the majority of plant metabolomics applications, there is a growing interest in combining the data from both platforms to effectively unravel the complexity of plant samples. The application of combined MS and NMR in the quality control of nutraceuticals forms the major part of this review. Finally I will look at the future developments and perspectives of these two technologies for the quality control of herbal materials.

Quality control system preparation for photogrammetric and laser scanning missions of Spanish national plan of aerial orthophotogpaphy (PNOA). (Polish Title: Opracowanie systemu kontroli jakości realizacji nalotów fotogrametrycznych i skaningowych dla hiszpańskiego narodowego planu ortofotomapy lotniczej (PNOA))

NASA Astrophysics Data System (ADS)

Rzonca, A.

2013-12-01

The paper presents the state of the art of quality control of photogrammetric and laser scanning data captured by airborne sensors. The described subject is very important for photogrammetric and LiDAR project execution, because the data quality a prior decides about the final product quality. On the other hand, precise and effective quality control process allows to execute the missions without wide margin of safety, especially in case of the mountain areas projects. For introduction, the author presents theoretical background of the quality control, basing on his own experience, instructions and technical documentation. He describes several variants of organization solutions. Basically, there are two main approaches: quality control of the captured data and the control of discrepancies of the flight plan and its results of its execution. Both of them are able to use test of control and analysis of the data. The test is an automatic algorithm controlling the data and generating the control report. Analysis is a less complicated process, that is based on documentation, data and metadata manual check. The example of quality control system for large area project was presented. The project is being realized periodically for the territory of all Spain and named National Plan of Aerial Orthophotography (Plan Nacional de Ortofotografía Aérea, PNOA). The system of the internal control guarantees its results soon after the flight and informs the flight team of the company. It allows to correct all the errors shortly after the flight and it might stop transferring the data to another team or company, for further data processing. The described system of data quality control contains geometrical and radiometrical control of photogrammetric data and geometrical control of LiDAR data. According to all specified parameters, it checks all of them and generates the reports. They are very helpful in case of some errors or low quality data. The paper includes the author experience in the field of data quality control, presents the conclusions and suggestions of the organization and technical aspects, with a short definition of the necessary control software.

Integrated Application of Quality-by-Design Principles to Drug Product Development: A Case Study of Brivanib Alaninate Film-Coated Tablets.

PubMed

Badawy, Sherif I F; Narang, Ajit S; LaMarche, Keirnan R; Subramanian, Ganeshkumar A; Varia, Sailesh A; Lin, Judy; Stevens, Tim; Shah, Pankaj A

2016-01-01

Modern drug product development is expected to follow quality-by-design (QbD) paradigm. At the same time, although there are several issue-specific examples in the literature that demonstrate the application of QbD principles, a holistic demonstration of the application of QbD principles to drug product development and control strategy, is lacking. This article provides an integrated case study on the systematic application of QbD to product development and demonstrates the implementation of QbD concepts in the different aspects of product and process design for brivanib alaninate film-coated tablets. Using a risk-based approach, the strategy for development entailed identification of product critical quality attributes (CQAs), assessment of risks to the CQAs, and performing experiments to understand and mitigate identified risks. Quality risk assessments and design of experiments were performed to understand the quality of the input raw materials required for a robust formulation and the impact of manufacturing process parameters on CQAs. In addition to the material property and process parameter controls, the proposed control strategy includes use of process analytical technology and conventional analytical tests to control in-process material attributes and ensure quality of the final product. Copyright © 2016. Published by Elsevier Inc.

Protein quality control in organelles - AAA/FtsH story.

PubMed

Janska, Hanna; Kwasniak, Malgorzata; Szczepanowska, Joanna

2013-02-01

This review focuses on organellar AAA/FtsH proteases, whose proteolytic and chaperone-like activity is a crucial component of the protein quality control systems of mitochondrial and chloroplast membranes. We compare the AAA/FtsH proteases from yeast, mammals and plants. The nature of the complexes formed by AAA/FtsH proteases and the current view on their involvement in degradation of non-native organellar proteins or assembly of membrane complexes are discussed. Additional functions of AAA proteases not directly connected with protein quality control found in yeast and mammals but not yet in plants are also described shortly. Following an overview of the molecular functions of the AAA/FtsH proteases we discuss physiological consequences of their inactivation in yeast, mammals and plants. The molecular basis of phenotypes associated with inactivation of the AAA/FtsH proteases is not fully understood yet, with the notable exception of those observed in m-AAA protease-deficient yeast cells, which are caused by impaired maturation of mitochondrial ribosomal protein. Finally, examples of cytosolic events affecting protein quality control in mitochondria and chloroplasts are given. This article is part of a Special Issue entitled: Protein Import and Quality Control in Mitochondria and Plastids. Copyright © 2012 Elsevier B.V. All rights reserved.

Concrete pavement quality control testing requirements needed for the super air meter : final report.

DOT National Transportation Integrated Search

2016-10-01

Concrete freeze-thaw durability is prominently linked to the air void system within the concrete. : Concrete pavements in Kansas undergo repetitive freeze-thaw cycles. Total air content measurements : currently used on fresh concrete do not provide a...

Final Environmental Impact Statement for Development of Facilities to Support Basing US Pacific Fleet F/A-18E/F Aircraft on the West Coast of the United States, Volume 1.

DTIC Science & Technology

1998-05-01

ROG reactive organic compound RONA Record of Non -applicability RTV rational threshold value RWQCB Regional Water Quality Control Board SARA...over water. The ranges are either scheduled via a designated military or civilian controlling agency (for restricted or warning areas) or are used...operations areas (MOAs), and air traffic control authorized airspace (ATCAA). Airspace designations throughout the United States are controlled by the Federal

Groundwater Monitoring Plan. Volume 2. Final Quality Assurance Project Plan

DTIC Science & Technology

1993-10-01

5 Table 4-2. US EPA Drinking Water MCLs ........................................ 4-6 Table 5-1. Sample Bottle Requirements, Preservation, and Holding... drinking water . " The types of quality control samples that will be collected during the Canal Creek groundwater monitoring program. ]- Jacobs...Revision No.: 0 Date: 10/27/93 Page: 6 of 9 Canal Creek Area, APG-EA, Maryland Groundwater Monitoring Plan, VOLUME I1 Table 4-2. US EPA Drinking Water

Daily peer review of abnormal cervical smears in the assessment of individual practice as an additional method of internal quality control.

PubMed

Confortini, M; Di Stefano, C; Biggeri, A; Bulgaresi, P; Di Claudio, G; Grisotto, L; Maddau, C; Matucci, M; Petreschi, C; Troni, G M; Turco, P; Foxi, P

2016-02-01

An important internal quality control system used in the Cancer Prevention and Research Institute cytopathology laboratory in Florence is the peer review procedure, based on the review of all abnormal cytological smears which routinely emerge. Peer review is an important training opportunity for all cytologists, especially for those with less experience. This article shows the results of the peer review procedure. Of the 63 754 Papanicolaou (Pap) smears screened in 2011, 1086 were considered to be abnormal [at least atypical squamous cells of undetermined significance (ASC-US+)] on primary screening (selected by a single cytologist) and were subjected to the peer review procedure. The overall performance of the laboratory's cytologists was evaluated using a multiple rater analysis and the comparison of each cytologist with the final diagnosis. Further, the agreement was assessed by means of Cohen's kappa and weighted kappa statistics. In general, a moderate/substantial level of agreement between the ten cytologists and the final diagnoses was evident. Kappa values for each reader compared with the final diagnosis ranged from 0.54 to 0.69. The overall kappa value was 0.62 [95% confidence interval (CI), 0.58-0.66] and overall weighted kappa value was 0.76 (95% CI, 0.74-0.79). The category-specific agreement showed the lowest values for atypical squamous cells, cannot exclude high-grade squamous intraepithelial lesion (ASC-H). In summary, peer review represents an important internal quality control in the evaluation and improvement of inter-observer agreement and of the functioning of the laboratory as a whole. Multi-head microscope sessions may improve particularly the reproducibility of borderline diagnoses and, above all, can be an important training contribution for cytologists. © 2014 John Wiley & Sons Ltd.

Source Apportionment of Final Particulate Matterin North China Plain based on Air Quality Modeling

NASA Astrophysics Data System (ADS)

Xing, J.; Wu, W.; Chang, X.; Wang, S.; Hao, J.

2016-12-01

Most Chinese cities in North China Plain are suffering from serious air pollution. To develop the regional air pollution control policies, we need to identify the major source contributions to such pollution and to design the control policy which is accurate, efficient and effective. This study used the air quality model with serval advanced technologies including ISAM and ERSM, to assess the source contributions from individual pollutants (incl. SO2, NOx, VOC, NH3, primary PM), sectors (incl. power plants, industry, transportation and domestic), and regions (Beijing, Hebei, Tianjing and surrounding provinces). The modeling period is two months in 2012 as January and July which represent winter and summer respectively. The non-linear relationship between air pollutant emissions and air quality will be addressed, and the integrated control of multi-pollutants and multi-regions in China will be suggested.

Quality Control Pathways for Nucleus-Encoded Eukaryotic tRNA Biosynthesis and Subcellular Trafficking

PubMed Central

Huang, Hsiao-Yun

2015-01-01

tRNAs perform an essential role in translating the genetic code. They are long-lived RNAs that are generated via numerous posttranscriptional steps. Eukaryotic cells have evolved numerous layers of quality control mechanisms to ensure that the tRNAs are appropriately structured, processed, and modified. We describe the known tRNA quality control processes that check tRNAs and correct or destroy aberrant tRNAs. These mechanisms employ two types of exonucleases, CCA end addition, tRNA nuclear aminoacylation, and tRNA subcellular traffic. We arrange these processes in order of the steps that occur from generation of precursor tRNAs by RNA polymerase (Pol) III transcription to end maturation and modification in the nucleus to splicing and additional modifications in the cytoplasm. Finally, we discuss the tRNA retrograde pathway, which allows tRNA reimport into the nucleus for degradation or repair. PMID:25848089

DOE Office of Scientific and Technical Information (OSTI.GOV)

Engels, J.

The Environmental Restoration (ER) Program was established for the investigation and remediation of inactive US Department of Energy (DOE) sites and facilities that have been declared surplus in terms of their previous uses. The purpose of this document is to Specify ER requirements for quality control (QC) of analytical data. Activities throughout all phases of the investigation may affect the quality of the final data product, thus are subject to control specifications. Laboratory control is emphasized in this document, and field concerns will be addressed in a companion document Energy Systems, in its role of technical coordinator and at themore » request of DOE-OR, extends the application of these requirements to all participants in ER activities. Because every instance and concern may not be addressed in this document, participants are encouraged to discuss any questions with the ER Quality Assurance (QA) Office, the Analytical Environmental Support Group (AESG), or the Analytical Project Office (APO).« less

A Control Law Design Method Facilitating Control Power, Robustness, Agility, and Flying Qualities Tradeoffs: CRAFT

NASA Technical Reports Server (NTRS)

Murphy, Patrick C.; Davidson, John B.

1998-01-01

A multi-input, multi-output control law design methodology, named "CRAFT", is presented. CRAFT stands for the design objectives addressed, namely, Control power, Robustness, Agility, and Flying Qualities Tradeoffs. The methodology makes use of control law design metrics from each of the four design objective areas. It combines eigenspace assignment, which allows for direct specification of eigenvalues and eigenvectors, with a graphical approach for representing the metrics that captures numerous design goals in one composite illustration. Sensitivity of the metrics to eigenspace choice is clearly displayed, enabling the designer to assess the cost of design tradeoffs. This approach enhances the designer's ability to make informed design tradeoffs and to reach effective final designs. An example of the CRAFT methodology applied to an advanced experimental fighter and discussion of associated design issues are provided.

Synthesis and quality control of fluorodeoxyglucose and performance assessment of Siemens MicroFocus 220 small animal PET scanner

NASA Astrophysics Data System (ADS)

Phaterpekar, Siddhesh Nitin

The scope of this article is to cover the synthesis and quality control procedures involved in production of Fludeoxyglucose (18F--FDG). The article also describes the cyclotron production of 18F radioisotope and gives a brief overview on operations and working of a fixed energy medical cyclotron. The quality control procedures for FDG involve radiochemical and radionuclidic purity tests, pH tests, chemical purity tests, sterility tests, endotoxin tests. Each of these procedures were carried out for multiple batches of FDG with a passing rate of 95% among 20 batches. The article also covers the quality assurance steps for the Siemens MicroPET Focus 220 Scanner using a Jaszczak phantom. We have carried out spatial resolution tests on the scanner, with an average transaxial resolution of 1.775mm with 2-3mm offset. Tests involved detector efficiency, blank scan sinograms and transmission sinograms. A series of radioactivity distribution tests are also carried out on a uniform phantom, denoting the variations in radioactivity and uniformity by using cylindrical ROIs in the transverse region of the final image. The purpose of these quality control tests is to make sure the manufactured FDG is biocompatible with the human body. Quality assurance tests are carried on PET scanners for efficient performance, and to make sure the quality of images acquired is according to the radioactivity distribution in the subject of interest.

Theoretical Model for Volume Fraction of UC, 235U Enrichment, and Effective Density of Final U 10Mo Alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Devaraj, Arun; Prabhakaran, Ramprashad; Joshi, Vineet V.

2016-04-12

The purpose of this document is to provide a theoretical framework for (1) estimating uranium carbide (UC) volume fraction in a final alloy of uranium with 10 weight percent molybdenum (U-10Mo) as a function of final alloy carbon concentration, and (2) estimating effective 235U enrichment in the U-10Mo matrix after accounting for loss of 235U in forming UC. This report will also serve as a theoretical baseline for effective density of as-cast low-enriched U-10Mo alloy. Therefore, this report will serve as the baseline for quality control of final alloy carbon content

Highway Safety Data : costs, quality, and strategies for improvement : final report

DOT National Transportation Integrated Search

1978-05-01

The objective of the experiment is to establish the influence of various types of trucks, buses and recreational vehicles on traffic flow on rural non-controlled access highways. This influence is due primarily to the low speeds which are common for ...

Medical Image Processing Server applied to Quality Control of Nuclear Medicine.

NASA Astrophysics Data System (ADS)

Vergara, C.; Graffigna, J. P.; Marino, E.; Omati, S.; Holleywell, P.

2016-04-01

This paper is framed within the area of medical image processing and aims to present the process of installation, configuration and implementation of a processing server of medical images (MIPS) in the Fundación Escuela de Medicina Nuclear located in Mendoza, Argentina (FUESMEN). It has been developed in the Gabinete de Tecnologia Médica (GA.TE.ME), Facultad de Ingeniería-Universidad Nacional de San Juan. MIPS is a software that using the DICOM standard, can receive medical imaging studies of different modalities or viewing stations, then it executes algorithms and finally returns the results to other devices. To achieve the objectives previously mentioned, preliminary tests were conducted in the laboratory. More over, tools were remotely installed in clinical enviroment. The appropiate protocols for setting up and using them in different services were established once defined those suitable algorithms. Finally, it’s important to focus on the implementation and training that is provided in FUESMEN, using nuclear medicine quality control processes. Results on implementation are exposed in this work.

Improved quantification of important beer quality parameters based on nonlinear calibration methods applied to FT-MIR spectra.

PubMed

Cernuda, Carlos; Lughofer, Edwin; Klein, Helmut; Forster, Clemens; Pawliczek, Marcin; Brandstetter, Markus

2017-01-01

During the production process of beer, it is of utmost importance to guarantee a high consistency of the beer quality. For instance, the bitterness is an essential quality parameter which has to be controlled within the specifications at the beginning of the production process in the unfermented beer (wort) as well as in final products such as beer and beer mix beverages. Nowadays, analytical techniques for quality control in beer production are mainly based on manual supervision, i.e., samples are taken from the process and analyzed in the laboratory. This typically requires significant lab technicians efforts for only a small fraction of samples to be analyzed, which leads to significant costs for beer breweries and companies. Fourier transform mid-infrared (FT-MIR) spectroscopy was used in combination with nonlinear multivariate calibration techniques to overcome (i) the time consuming off-line analyses in beer production and (ii) already known limitations of standard linear chemometric methods, like partial least squares (PLS), for important quality parameters Speers et al. (J I Brewing. 2003;109(3):229-235), Zhang et al. (J I Brewing. 2012;118(4):361-367) such as bitterness, citric acid, total acids, free amino nitrogen, final attenuation, or foam stability. The calibration models are established with enhanced nonlinear techniques based (i) on a new piece-wise linear version of PLS by employing fuzzy rules for local partitioning the latent variable space and (ii) on extensions of support vector regression variants (-PLSSVR and ν-PLSSVR), for overcoming high computation times in high-dimensional problems and time-intensive and inappropriate settings of the kernel parameters. Furthermore, we introduce a new model selection scheme based on bagged ensembles in order to improve robustness and thus predictive quality of the final models. The approaches are tested on real-world calibration data sets for wort and beer mix beverages, and successfully compared to linear methods, showing a clear out-performance in most cases and being able to meet the model quality requirements defined by the experts at the beer company. Figure Workflow for calibration of non-Linear model ensembles from FT-MIR spectra in beer production .

76 FR 8753 - Final Information Quality Guidelines Policy

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-15

... DEPARTMENT OF HOMELAND SECURITY Final Information Quality Guidelines Policy AGENCY: Department of Homeland Security. ACTION: Notice and request for public comment on Final Information Quality Guidelines. SUMMARY: These guidelines should be used to ensure and maximize the quality of disseminated information...

77 FR 28423 - Final Rule To Implement the 1997 8-Hour Ozone National Ambient Air Quality Standard...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-14

...The EPA is revising the rules for implementing the 1997 8-hour ozone national ambient air quality standards (NAAQS) to address certain limited portions of the rules vacated by the U.S. Court of Appeals for the District of Columbia Circuit. This final rule assigns Clean Air Act (CAA or Act) classifications and associated state planning and control requirements to selected ozone nonattainment areas. This final rule also addresses three vacated provisions of the 1997 8-hour NAAQS--Phase 1 Implementation Rule (April 30, 2004) that provided exemptions from the anti-backsliding requirements relating to nonattainment area New Source Review (NSR), CAA section 185 penalty fees, and contingency measures, as these three requirements applied for the 1-hour standard. This rule also reinstates the 1-hour contingency measures as applicable requirements that must be retained until the area attains the 1997 8- hour ozone standard. Finally, this rule deletes an obsolete provision that stayed the EPA's authority to revoke the 1-hour ozone standard pending the Agency's issuance of a final rule that revises or reinstates its revocation authority and considers and addresses certain other issues. That rule has now been issued.

Sequence verification as quality-control step for production of cDNA microarrays.

PubMed

Taylor, E; Cogdell, D; Coombes, K; Hu, L; Ramdas, L; Tabor, A; Hamilton, S; Zhang, W

2001-07-01

To generate cDNA arrays in our core laboratory, we amplified about 2300 PCR products from a human, sequence-verified cDNA clone library. As a quality-control step, we sequenced the PCR products immediately before printing. The sequence information was used to search the GenBank database to confirm the identities. Although these clones were previously sequence verified by the company, we found that only 79% of the clones matched the original database after handling. Our experience strongly indicates the necessity to sequence verify the clones at the final stage before printing on microarray slides and to modify the gene list accordingly.

Method of controlling coherent synchroton radiation-driven degradation of beam quality during bunch length compression

DOEpatents

Douglas, David R [Newport News, VA; Tennant, Christopher D [Williamsburg, VA

2012-07-10

A method of avoiding CSR induced beam quality defects in free electron laser operation by a) controlling the rate of compression and b) using a novel means of integrating the compression with the remainder of the transport system: both are accomplished by means of dispersion modulation. A large dispersion is created in the penultimate dipole magnet of the compression region leading to rapid compression; this large dispersion is demagnified and dispersion suppression performed in a final small dipole. As a result, the bunch is short for only a small angular extent of the transport, and the resulting CSR excitation is small.

A Process Management System for Networked Manufacturing

NASA Astrophysics Data System (ADS)

Liu, Tingting; Wang, Huifen; Liu, Linyan

With the development of computer, communication and network, networked manufacturing has become one of the main manufacturing paradigms in the 21st century. Under the networked manufacturing environment, there exist a large number of cooperative tasks susceptible to alterations, conflicts caused by resources and problems of cost and quality. This increases the complexity of administration. Process management is a technology used to design, enact, control, and analyze networked manufacturing processes. It supports efficient execution, effective management, conflict resolution, cost containment and quality control. In this paper we propose an integrated process management system for networked manufacturing. Requirements of process management are analyzed and architecture of the system is presented. And a process model considering process cost and quality is developed. Finally a case study is provided to explain how the system runs efficiently.

Development, optimization and validation of gas chromatographic fingerprinting of Brazilian commercial diesel fuel for quality control.

PubMed

dos Santos, Bruno César Diniz Brito; Flumignan, Danilo Luiz; de Oliveira, José Eduardo

2012-10-01

A three-step development, optimization and validation strategy is described for gas chromatography (GC) fingerprints of Brazilian commercial diesel fuel. A suitable GC-flame ionization detection (FID) system was selected to assay a complex matrix such as diesel. The next step was to improve acceptable chromatographic resolution with reduced analysis time, which is recommended for routine applications. Full three-level factorial designs were performed to improve flow rate, oven ramps, injection volume and split ratio in the GC system. Finally, several validation parameters were performed. The GC fingerprinting can be coupled with pattern recognition and multivariate regressions analyses to determine fuel quality and fuel physicochemical parameters. This strategy can also be applied to develop fingerprints for quality control of other fuel types.

[Which one is more important, raw materials or productive technology?--a case study for quality consistency control of Gegen Qinlian decoction].

PubMed

Zhong, Wen; Chen, Sha; Zhang, Jun; Wang, Yu-Sheng; Liu, An

2016-03-01

To investigate the effect of Chinese medicine raw materials and production technology on quality consistency of Chinese patent medicines with Gegen Qinlian decoction as an example, and establish a suitable method for the quality consistency control of Chinese patent medicines. The results showed that the effect of production technology on the quality consistency was generally not more than 5%, while the effect of raw materials was even more than 30%, indicating that the effect of raw materials was much greater than that of the production technology. In this study, blend technology was used to improve the quality consistency of raw materials. As a result, the difference between the product produced by raw materials and reference groups was less than 5%, thus increasing the quality consistence of finished products. The results showed that under the current circumstances, the main factor affecting the quality consistency of Chinese patent medicines was raw materials, so we shall pay more attention to the quality of Chinese medicine's raw materials. Finally, a blend technology can improve the quality consistency of Chinese patent medicines. Copyright© by the Chinese Pharmaceutical Association.

Greening the Engineering and Technology Curriculum via Real Life Hands-on Projects

USDA-ARS?s Scientific Manuscript database

This paper aims at demonstrating how greening efforts can be embedded into science and engineering courses without major curricular changes. In this regard, examples of final projects assigned in a statistical quality control, a 500-level, graduate engineering course, focusing on campus sustainabili...

An Abridged History of Medical Informatics Education in Europe

PubMed Central

Hasman, Arie; Mantas, John; Zarubina, Tatyana

2014-01-01

This contribution presents the development of medical informatics education in Europe. It does not discuss all developments that took place. Rather it discerns several themes that indicate the progress in the field, starting from the initiation phase to the final quality control phase. PMID:24648617

Faculty Return to Industry. Final Report.

ERIC Educational Resources Information Center

Hulse, David R.

Lagging productivity and increased competitiveness from abroad are forcing U.S. management companies to adopt new management styles that promote efficiency and quality in production. High on the agenda is the incorporation of Statistical Process Control (SPC). SPC requires definition of process and product specifications to facilitate their…

Space Shuttle flying qualities criteria assessment. Phase 5: Data acquistion and analysis

NASA Technical Reports Server (NTRS)

Myers, T. T.; Johnston, D. E.; Mcruer, D. T.

1986-01-01

The development of flying qualities experiments (OFQ) as a part of the Orbiter Experiments Program (OEX) was continued. The data base was extended to use the ground based cinetheodolite measurements of orbiter approach and landing. Onboard the cinetheodolite data were analyzed from flights STS 2 through 7 to identify the effective augmented vehicle dynamics, the control strategy employed by the pilot during preflare, shallow glide, and final flare segments of the landing, and the key approach and touchdown performance measures. A plan for an OFQ flying qualities data archive and processing is presented.

Impact of interventions to improve the quality of peer review of biomedical journals: a systematic review and meta-analysis.

PubMed

Bruce, Rachel; Chauvin, Anthony; Trinquart, Ludovic; Ravaud, Philippe; Boutron, Isabelle

2016-06-10

The peer review process is a cornerstone of biomedical research. We aimed to evaluate the impact of interventions to improve the quality of peer review for biomedical publications. We performed a systematic review and meta-analysis. We searched CENTRAL, MEDLINE (PubMed), Embase, Cochrane Database of Systematic Reviews, and WHO ICTRP databases, for all randomized controlled trials (RCTs) evaluating the impact of interventions to improve the quality of peer review for biomedical publications. We selected 22 reports of randomized controlled trials, for 25 comparisons evaluating training interventions (n = 5), the addition of a statistical peer reviewer (n = 2), use of a checklist (n = 2), open peer review (i.e., peer reviewers informed that their identity would be revealed; n = 7), blinded peer review (i.e., peer reviewers blinded to author names and affiliation; n = 6) and other interventions to increase the speed of the peer review process (n = 3). Results from only seven RCTs were published since 2004. As compared with the standard peer review process, training did not improve the quality of the peer review report and use of a checklist did not improve the quality of the final manuscript. Adding a statistical peer review improved the quality of the final manuscript (standardized mean difference (SMD), 0.58; 95 % CI, 0.19 to 0.98). Open peer review improved the quality of the peer review report (SMD, 0.14; 95 % CI, 0.05 to 0.24), did not affect the time peer reviewers spent on the peer review (mean difference, 0.18; 95 % CI, -0.06 to 0.43), and decreased the rate of rejection (odds ratio, 0.56; 95 % CI, 0.33 to 0.94). Blinded peer review did not affect the quality of the peer review report or rejection rate. Interventions to increase the speed of the peer review process were too heterogeneous to allow for pooling the results. Despite the essential role of peer review, only a few interventions have been assessed in randomized controlled trials. Evidence-based peer review needs to be developed in biomedical journals.

An introduction to statistical process control in research proteomics.

PubMed

Bramwell, David

2013-12-16

Statistical process control is a well-established and respected method which provides a general purpose, and consistent framework for monitoring and improving the quality of a process. It is routinely used in many industries where the quality of final products is critical and is often required in clinical diagnostic laboratories [1,2]. To date, the methodology has been little utilised in research proteomics. It has been shown to be capable of delivering quantitative QC procedures for qualitative clinical assays [3] making it an ideal methodology to apply to this area of biological research. To introduce statistical process control as an objective strategy for quality control and show how it could be used to benefit proteomics researchers and enhance the quality of the results they generate. We demonstrate that rules which provide basic quality control are easy to derive and implement and could have a major impact on data quality for many studies. Statistical process control is a powerful tool for investigating and improving proteomics research work-flows. The process of characterising measurement systems and defining control rules forces the exploration of key questions that can lead to significant improvements in performance. This work asserts that QC is essential to proteomics discovery experiments. Every experimenter must know the current capabilities of their measurement system and have an objective means for tracking and ensuring that performance. Proteomic analysis work-flows are complicated and multi-variate. QC is critical for clinical chemistry measurements and huge strides have been made in ensuring the quality and validity of results in clinical biochemistry labs. This work introduces some of these QC concepts and works to bridge their use from single analyte QC to applications in multi-analyte systems. This article is part of a Special Issue entitled: Standardization and Quality Control in Proteomics. Copyright © 2013 The Author. Published by Elsevier B.V. All rights reserved.

Implementation of hazard analysis and critical control point (HACCP) in dried anchovy production process

NASA Astrophysics Data System (ADS)

Citraresmi, A. D. P.; Wahyuni, E. E.

2018-03-01

The aim of this study was to inspect the implementation of Hazard Analysis and Critical Control Point (HACCP) for identification and prevention of potential hazards in the production process of dried anchovy at PT. Kelola Mina Laut (KML), Lobuk unit, Sumenep. Cold storage process is needed in each anchovy processing step in order to maintain its physical and chemical condition. In addition, the implementation of quality assurance system should be undertaken to maintain product quality. The research was conducted using a survey method, by following the whole process of making anchovy from the receiving raw materials to the packaging of final product. The method of data analysis used was descriptive analysis method. Implementation of HACCP at PT. KML, Lobuk unit, Sumenep was conducted by applying Pre Requisite Programs (PRP) and preparation stage consisting of 5 initial stages and 7 principles of HACCP. The results showed that CCP was found in boiling process flow with significant hazard of Listeria monocytogenesis bacteria and final sorting process with significant hazard of foreign material contamination in the product. Actions taken were controlling boiling temperature of 100 – 105°C for 3 - 5 minutes and training for sorting process employees.

A simulation investigation of scout/attack helicopter directional control requirements for hover and low-speed tasks

NASA Technical Reports Server (NTRS)

Bivens, Courtland C.; Guercio, Joseph G.

1987-01-01

A piloted simulator experiment was conducted to investigate directional axis handling qualities requirements for low speed and hover tasks performed by a Scout/Attack helicopter. Included were the directional characteristics of various candidate light helicopter family configurations. Also, the experiment focused on conventional single main/tail rotor configurations of the OH-58 series aircraft, where the first-order yaw-axis dynamic effects that contributed to the loss of tail rotor control were modeled. Five pilots flew 22 configurations under various wind conditions. Cooper-Harper handling quality ratings were used as the primary measure of merit of each configuration. The results of the experiment indicate that rotorcraft configurations with high directional gust sensitivity require greater minimum yaw damping to maintain satisfactory handling qualities during nap-of-the-Earth flying tasks. It was also determined that both yaw damping and control response are critical handling qualities parameters in performing the air-to-air target acquisition and tracking task. Finally, the lack of substantial yaw damping and larger values of gust sensitivity increased the possibility of loss of directional control at low airspeeds for the single main/tail rotor configurations.

10 CFR 440.12 - State application.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the method used by the State to insure the quality of work and adequate financial management control... include a copy of the final State plan; (3) The budget for total funds applied for under the Act, which....18(d) for State administration; (4) The total number of dwelling units proposed to be weatherized...

76 FR 64020 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-17

... Plastic Parts and Business Machines Coatings AGENCY: Environmental Protection Agency (EPA). ACTION: Final....19.07-2, Plastic Parts and Business Machines Coating. Maryland's SIP revision meets the requirement... Techniques Guidelines (CTG) standards for plastic parts and business machines coatings and will help Maryland...

78 FR 78726 - Approval and Promulgation of Air Quality Implementation Plans; Indiana; Volatile Organic Compound...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R05-OAR-2012-0453; FRL-9904-35-Region 5... Control Measures for Industrial Solvent Cleaning for Northwest Indiana AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: The Environmental Protection Agency (EPA) is approving a...

77 FR 43000 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Offset Lithographic...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-23

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R03-OAR-2012-0042; FRL-9702-2] Approval and... Printing Regulations AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: EPA is... Technology (RACT) for sources covered by EPA's Control Techniques Guidelines (CTG) for offset lithographic...

77 FR 22497 - Approval and Promulgation of Air Quality Implementation Plans; Illinois; Small Container...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-16

... surface coating operations in the Chicago and Metro-East St. Louis 8-hour ozone nonattainment areas. These... available control technology (RACT) policy. DATES: This direct final rule will be effective June 15, 2012... ``small container exemption'' for pleasure craft surface coating operations. EPA previously approved...

Application of quality by design (QbD) to formulation and processing of naproxen pellets by extrusion-spheronization.

PubMed

Wang, Junlin; Kan, Shuling; Chen, Tong; Liu, Jianping

2015-03-01

The aim of this research was to apply quality by design (QbD) to the development of naproxen loaded core pellets which can be used as the potential core for colon-specific pellets. In the early stages of this study, prior knowledge and preliminary studies were systematically incorporated into the risk assessment using failure mode and effect analysis (FMEA) and fishbone diagram. Then Plackett-Burman design was used to screen eight potential high risk factors (spheronization speed, spheronization time, extrusion speed, drying method, CCMC-Na concentration, lactose concentration, water concentration and Tween 80 concentration) obtained from the above risk assessment. It was discovered that out of the eight potential high risk factors only three factors (spheronization speed, extrusion speed and CCMC-Na concentration) had significant effects on the quality of the pellets. This allowed the use of Box-Behnken design (BBD) to fully elucidate the relationship between the variables and critical quality attribute (CQA). Finally, the final control space was established within which the quality of the pellets can meet the requirement of colon-specific drug delivery system. This study demonstrated that naproxen loaded core pellets were successfully designed using QbD principle.

Effectiveness of a Voice Training Program for Student Teachers on Vocal Health.

PubMed

Richter, Bernhard; Nusseck, Manfred; Spahn, Claudia; Echternach, Matthias

2016-07-01

The effectiveness of a preventive training program on vocal health for German student teachers was investigated on specific vocal parameters. The voice quality as described by the Dysphonia Severity Index of 204 student teachers (training group: n = 123; control group: n = 81) was measured at the beginning and at the end of the student teachers training period (duration 1.5 years). Additionally, for investigating the voice-carrying capacity, a vocal loading test (VLT) was performed. Finally, participants had to provide a subjective judgment of a possible Voice Handicap Index. The training program improved the voice quality of the trained group compared with that of the control group, whose voice quality declined. The trained group was also able to better sustain their voice quality across the VLT than the control group. Both groups, however, reported a similar increase in subjective vocal strain. The presented training program clearly showed a positive impact on the voice quality and the vocal capacity. The results maintain the importance of such a training program to be integrated in the education and occupational routine of teachers. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Quality Aware Compression of Electrocardiogram Using Principal Component Analysis.

PubMed

Gupta, Rajarshi

2016-05-01

Electrocardiogram (ECG) compression finds wide application in various patient monitoring purposes. Quality control in ECG compression ensures reconstruction quality and its clinical acceptance for diagnostic decision making. In this paper, a quality aware compression method of single lead ECG is described using principal component analysis (PCA). After pre-processing, beat extraction and PCA decomposition, two independent quality criteria, namely, bit rate control (BRC) or error control (EC) criteria were set to select optimal principal components, eigenvectors and their quantization level to achieve desired bit rate or error measure. The selected principal components and eigenvectors were finally compressed using a modified delta and Huffman encoder. The algorithms were validated with 32 sets of MIT Arrhythmia data and 60 normal and 30 sets of diagnostic ECG data from PTB Diagnostic ECG data ptbdb, all at 1 kHz sampling. For BRC with a CR threshold of 40, an average Compression Ratio (CR), percentage root mean squared difference normalized (PRDN) and maximum absolute error (MAE) of 50.74, 16.22 and 0.243 mV respectively were obtained. For EC with an upper limit of 5 % PRDN and 0.1 mV MAE, the average CR, PRDN and MAE of 9.48, 4.13 and 0.049 mV respectively were obtained. For mitdb data 117, the reconstruction quality could be preserved up to CR of 68.96 by extending the BRC threshold. The proposed method yields better results than recently published works on quality controlled ECG compression.

Final Environmental Assessment for the Establishment of an Air-to-Surface Helicopter Gunnery Training Target Set at White Sands Missile Range, New Mexico

DTIC Science & Technology

2007-12-01

AQCR Air Quality Control Region AR Army Regulation ARC Acoustic Research Complex BLM Bureau of Land Management BMP best management practice CAA...night average A-weighted sound level mg/m3 milligrams per cubic meter MSL mean sea level NAAQS National Ambient Air Quality Standards NASA ...unique characteristics required by the U.S. Army, U.S. Navy, USAF, National Aeronautics and Space Administration ( NASA ), and other Federal and

Quality controls for gamma cameras and PET cameras: development of a free open-source ImageJ program

NASA Astrophysics Data System (ADS)

Carlier, Thomas; Ferrer, Ludovic; Berruchon, Jean B.; Cuissard, Regis; Martineau, Adeline; Loonis, Pierre; Couturier, Olivier

2005-04-01

Acquisition data and treatments for quality controls of gamma cameras and Positron Emission Tomography (PET) cameras are commonly performed with dedicated program packages, which are running only on manufactured computers and differ from each other, depending on camera company and program versions. The aim of this work was to develop a free open-source program (written in JAVA language) to analyze data for quality control of gamma cameras and PET cameras. The program is based on the free application software ImageJ and can be easily loaded on any computer operating system (OS) and thus on any type of computer in every nuclear medicine department. Based on standard parameters of quality control, this program includes 1) for gamma camera: a rotation center control (extracted from the American Association of Physics in Medicine, AAPM, norms) and two uniformity controls (extracted from the Institute of Physics and Engineering in Medicine, IPEM, and National Electronic Manufacturers Association, NEMA, norms). 2) For PET systems, three quality controls recently defined by the French Medical Physicist Society (SFPM), i.e. spatial resolution and uniformity in a reconstructed slice and scatter fraction, are included. The determination of spatial resolution (thanks to the Point Spread Function, PSF, acquisition) allows to compute the Modulation Transfer Function (MTF) in both modalities of cameras. All the control functions are included in a tool box which is a free ImageJ plugin and could be soon downloaded from Internet. Besides, this program offers the possibility to save on HTML format the uniformity quality control results and a warning can be set to automatically inform users in case of abnormal results. The architecture of the program allows users to easily add any other specific quality control program. Finally, this toolkit is an easy and robust tool to perform quality control on gamma cameras and PET cameras based on standard computation parameters, is free, run on any type of computer and will soon be downloadable from the net (http://rsb.info.nih.gov/ij/plugins or http://nucleartoolkit.free.fr).

Statistical process control based chart for information systems security

NASA Astrophysics Data System (ADS)

Khan, Mansoor S.; Cui, Lirong

2015-07-01

Intrusion detection systems have a highly significant role in securing computer networks and information systems. To assure the reliability and quality of computer networks and information systems, it is highly desirable to develop techniques that detect intrusions into information systems. We put forward the concept of statistical process control (SPC) in computer networks and information systems intrusions. In this article we propose exponentially weighted moving average (EWMA) type quality monitoring scheme. Our proposed scheme has only one parameter which differentiates it from the past versions. We construct the control limits for the proposed scheme and investigate their effectiveness. We provide an industrial example for the sake of clarity for practitioner. We give comparison of the proposed scheme with EWMA schemes and p chart; finally we provide some recommendations for the future work.

Land cover controls on summer discharge and runoff solution chemistry of semi-arid urban catchments

NASA Astrophysics Data System (ADS)

Gallo, Erika L.; Brooks, Paul D.; Lohse, Kathleen A.; McLain, Jean E. T.

2013-04-01

SummaryRecharge of urban runoff to groundwater as a stormwater management practice has gained importance in semi-arid regions where water resources are scarce and urban centers are growing. Despite this trend, the importance of land cover in controlling semi-arid catchment runoff quantity and quality remains unclear. Here we address the question: How do land cover characteristics control the amount and quality of storm runoff in semi-arid urban catchments? We monitored summertime runoff quantity and quality from five catchments dominated by distinct urban land uses: low, medium, and high density residential, mixed use, and commercial. Increasing urban land cover increased runoff duration and the likelihood that a rainfall event would result in runoff, but did not increase the time to peak discharge of episodic runoff. The effect of urban land cover on hydrologic responses was tightly coupled to the magnitude of rainfall. At distinct rainfall thresholds, roads, percent impervious cover and the stormwater drainage network controlled runoff frequency, runoff depth and runoff ratios. Contrary to initial expectations, runoff quality did not vary in repose to impervious cover or land use. We identified four major mechanisms controlling runoff quality: (1) variable solute sourcing due to land use heterogeneity and above ground catchment connectivity; (2) the spatial extent of pervious and biogeochemically active areas; (3) the efficiency of overland flow and runoff mobilization; and (4) solute flushing and dilution. Our study highlights the importance of the stormwater drainage systems characteristics in controlling urban runoff quantity and quality; and suggests that enhanced wetting and in-stream processes may control solute sourcing and retention. Finally, we suggest that the characteristics of the stormwater drainage system should be integrated into stormwater management approaches.

3D printing X-Ray Quality Control Phantoms. A Low Contrast Paradigm

NASA Astrophysics Data System (ADS)

Kapetanakis, I.; Fountos, G.; Michail, C.; Valais, I.; Kalyvas, N.

2017-11-01

Current 3D printing technology products may be usable in various biomedical applications. Such an application is the creation of X-ray quality control phantoms. In this work a self-assembled 3D printer (geeetech i3) was used for the design of a simple low contrast phantom. The printing material was Polylactic Acid (PLA) (100% printing density). Low contrast scheme was achieved by creating air-holes with different diameters and thicknesses, ranging from 1mm to 9mm. The phantom was irradiated at a Philips Diagnost 93 fluoroscopic installation at 40kV-70kV with the semi-automatic mode. The images were recorded with an Agfa cr30-x CR system and assessed with ImageJ software. The best contrast value observed was approximately 33%. In low contrast detectability check it was found that the 1mm diameter hole was always visible, for thickness larger or equal to 4mm. A reason for not being able to distinguish 1mm in smaller thicknesses might be the presence of printing patterns on the final image, which increased the structure noise. In conclusion the construction of a contrast resolution phantom with a 3D printer is feasible. The quality of the final product depends upon the printer accuracy and the material characteristics.

Challenges in Special Steel Making

NASA Astrophysics Data System (ADS)

Balachandran, G.

2018-02-01

Special bar quality [SBQ] is a long steel product where an assured quality is delivered by the steel mill to its customer. The bars have enhanced tolerance to higher stress application and it is demanded for specialised component making. The SBQ bars are sought for component making processing units such as closed die hot forging, hot extrusion, cold forging, machining, heat treatment, welding operations. The final component quality of the secondary processing units depends on the quality maintained at the steel maker end along with quality maintained at the fabricator end. Thus, quality control is ensured at every unit process stages. The various market segments catered to by SBQ steel segment is ever growing and is reviewed. Steel mills need adequate infrastructure and technological capability to make these higher quality steels. Some of the critical stages of processing SBQ and the critical quality maintenance parameters at the steel mill in the manufacture has been brought out.

An analytical approach for predicting pilot induced oscillations

NASA Technical Reports Server (NTRS)

Hess, R. A.

1981-01-01

The optimal control model (OCM) of the human pilot is applied to the study of aircraft handling qualities. Attention is focused primarily on longitudinal tasks. The modeling technique differs from previous applications of the OCM in that considerable effort is expended in simplifying the pilot/vehicle analysis. After briefly reviewing the OCM, a technique for modeling the pilot controlling higher order systems is introduced. Following this, a simple criterion or determining the susceptability of an aircraft to pilot induced oscillations (PIO) is formulated. Finally, a model-based metric for pilot rating prediction is discussed. The resulting modeling procedure provides a relatively simple, yet unified approach to the study of a variety of handling qualities problems.

Medicare Program; FY 2017 Hospice Wage Index and Payment Rate Update and Hospice Quality Reporting Requirements. Final rule.

PubMed

2016-08-05

This final rule will update the hospice wage index, payment rates, and cap amount for fiscal year (FY) 2017. In addition, this rule changes the hospice quality reporting program, including adopting new quality measures. Finally, this final rule includes information regarding the Medicare Care Choices Model (MCCM).

Standard Free Droplet Digital Polymerase Chain Reaction as a New Tool for the Quality Control of High-Capacity Adenoviral Vectors in Small-Scale Preparations

PubMed Central

Boehme, Philip; Stellberger, Thorsten; Solanki, Manish; Zhang, Wenli; Schulz, Eric; Bergmann, Thorsten; Liu, Jing; Doerner, Johannes; Baiker, Armin E.

2015-01-01

Abstract High-capacity adenoviral vectors (HCAdVs) are promising tools for gene therapy as well as for genetic engineering. However, one limitation of the HCAdV vector system is the complex, time-consuming, and labor-intensive production process and the following quality control procedure. Since HCAdVs are deleted for all viral coding sequences, a helper virus (HV) is needed in the production process to provide the sequences for all viral proteins in trans. For the purification procedure of HCAdV, cesium chloride density gradient centrifugation is usually performed followed by buffer exchange using dialysis or comparable methods. However, performing these steps is technically difficult, potentially error-prone, and not scalable. Here, we establish a new protocol for small-scale production of HCAdV based on commercially available adenovirus purification systems and a standard method for the quality control of final HCAdV preparations. For titration of final vector preparations, we established a droplet digital polymerase chain reaction (ddPCR) that uses a standard free-end-point PCR in small droplets of defined volume. By using different probes, this method is capable of detecting and quantifying HCAdV and HV in one reaction independent of reference material, rendering this method attractive for accurately comparing viral titers between different laboratories. In summary, we demonstrate that it is possible to produce HCAdV in a small scale of sufficient quality and quantity to perform experiments in cell culture, and we established a reliable protocol for vector titration based on ddPCR. Our method significantly reduces time and required equipment to perform HCAdV production. In the future the ddPCR technology could be advantageous for titration of other viral vectors commonly used in gene therapy. PMID:25640117

[Application of microscopic spectroscopy in quality control of Niuhuang Qingxin pills].

PubMed

Nie, Li-Xing; Zhang, Ye; Zhang, Nan-Ping; Hu, Xiao-Ru; Kang, Shuai; Hou, Jian-Zhong; Dai, Zhong; Ma, Shuang-Cheng

2016-10-01

Application of microscopic spectroscopy in quality control of Niuhuang Qingxin pills was discussed. First, microscopic characteristics specified by the statutory standard of Niuhuang Qingxin pills were summarized. Then new identification method was established for Dioscoreae Rhizoma, Saigae Tataricae Cornu, Cinnamomi Cortex and Saposhnikoviae Radix. Finally, microscopic spectroscopy was used for test of Dioscoreae Rhizoma's adulterant Dioscoreae Fordii Rhizoma.It was the first time for this technology being applied in adulteration test of Chinese patent medicine.The results showed that Saigae Tataricae Cornu was not detected in 2 batches of Niuhuang Qingxin pills from 1 manufacturer while Dioscoreae Fordii Rhizoma was detected in 3 batches of samples from 2 manufacturers. The proposed methods were accurate, simple, rapid, objective and economic, which offered a more comprehensive approach for quality control of Niuhuang Qingxin pills. It was indicated that conventional technology such as microscopic spectroscopy could play an important role in identification of traditional Chinese medicine whose index ingredient was deficient or tiny. Copyright© by the Chinese Pharmaceutical Association.

Quality control for the first large areas of triple-GEM chambers for the CMS endcaps

NASA Astrophysics Data System (ADS)

Abbaneo, D.; Abbas, M.; Abbrescia, M.; Abi Akl, M.; Aboamer, O.; Acosta, D.; Ahmad, A.; Ahmed, W.; Aleksandrov, A.; Altieri, P.; Asawatangtrakuldee, C.; Aspell, P.; Assran, Y.; Awan, I.; Bally, S.; Ban, Y.; Banerjee, S.; Barashko, V.; Barria, P.; Bencze, G.; Beni, N.; Benussi, L.; Bhopatkar, V.; Bianco, S.; Bos, J.; Bouhali, O.; Braghieri, A.; Braibant, S.; Buontempo, S.; Calabria, C.; Caponero, M.; Caputo, C.; Cassese, F.; Castaneda, A.; Cauwenbergh, S.; Cavallo, F. R.; Celik, A.; Choi, M.; Choi, S.; Christiansen, J.; Cimmino, A.; Colafranceschi, S.; Colaleo, A.; Conde Garcia, A.; Czellar, S.; Dabrowski, M. M.; De Lentdecker, G.; De Oliveira, R.; de Robertis, G.; Dildick, S.; Dorney, B.; Endroczi, G.; Errico, F.; Fenyvesi, A.; Ferry, S.; Furic, I.; Giacomelli, P.; Gilmore, J.; Golovtsov, V.; Guiducci, L.; Guilloux, F.; Gutierrez, A.; Hadjiiska, R. M.; Hauser, J.; Hoepfner, K.; Hohlmann, M.; Hoorani, H.; Iaydjiev, P.; Jeng, Y. G.; Kamon, T.; Karchin, P.; Korytov, A.; Krutelyov, S.; Kumar, A.; Kim, H.; Lee, J.; Lenzi, T.; Litov, L.; Loddo, F.; Madorsky, A.; Maerschalk, T.; Maggi, M.; Magnani, A.; Mal, P. K.; Mandal, K.; Marchioro, A.; Marinov, A.; Majumdar, N.; Merlin, J. A.; Mitselmakher, G.; Mohanty, A. K.; Mohapatra, A.; Molnar, J.; Muhammad, S.; Mukhopadhyay, S.; Naimuddin, M.; Nuzzo, S.; Oliveri, E.; Pant, L. M.; Paolucci, P.; Park, I.; Passeggio, G.; Pavlov, B.; Philipps, B.; Piccolo, D.; Postema, H.; Puig Baranac, A.; Radi, A.; Radogna, R.; Raffone, G.; Ranieri, A.; Rashevski, G.; Riccardi, C.; Rodozov, M.; Rodrigues, A.; Ropelewski, L.; RoyChowdhury, S.; Ryu, G.; Ryu, M. S.; Safonov, A.; Salva, S.; Saviano, G.; Sharma, A.; Sharma, A.; Sharma, R.; Shah, A. H.; Shopova, M.; Sturdy, J.; Sultanov, G.; Swain, S. K.; Szillasi, Z.; Talvitie, J.; Tatarinov, A.; Tuuva, T.; Tytgat, M.; Vai, I.; Van Stenis, M.; Venditti, R.; Verhagen, E.; Verwilligen, P.; Vitulo, P.; Volkov, S.; Vorobyev, A.; Wang, D.; Wang, M.; Yang, U.; Yang, Y.; Yonamine, R.; Zaganidis, N.; Zenoni, F.; Zhang, A.

2018-02-01

The CMS Collaboration plans to equip the very forward muon system with triple-GEM detectors that can withstand the environment of the High-Luminosity LHC. This project is at the final stages of R&D and moving to production. An unprecedented large area of several 100 m2 are to be instrumented with GEM detectors which will be produced in six different sites around the world. A common construction and quality control procedure is required to ensure the performance of each detector. The quality control steps will include optical inspection, cleaning and baking of all materials and parts used to build the detector, leakage current tests of the GEM foils, high voltage tests, gas leak tests of the chambers and monitoring pressure drop vs. time, gain calibration to know the optimal operation region of the detector, gain uniformity tests, and studying the efficiency, noise and tracking performance of the detectors in a cosmic stand using scintillators.

The consistency approach for quality control of vaccines - a strategy to improve quality control and implement 3Rs.

PubMed

De Mattia, Fabrizio; Chapsal, Jean-Michel; Descamps, Johan; Halder, Marlies; Jarrett, Nicholas; Kross, Imke; Mortiaux, Frederic; Ponsar, Cecile; Redhead, Keith; McKelvie, Jo; Hendriksen, Coenraad

2011-01-01

Current batch release testing of established vaccines emphasizes quality control of the final product and is often characterized by extensive use of animals. This report summarises the discussions of a joint ECVAM/EPAA workshop on the applicability of the consistency approach for routine release of human and veterinary vaccines and its potential to reduce animal use. The consistency approach is based upon thorough characterization of the vaccine during development and the principle that the quality of subsequent batches is the consequence of the strict application of a quality system and of a consistent production of batches. The concept of consistency of production is state-of-the-art for new-generation vaccines, where batch release is mainly based on non-animal methods. There is now the opportunity to introduce the approach into established vaccine production, where it has the potential to replace in vivo tests with non-animal tests designed to demonstrate batch quality while maintaining the highest quality standards. The report indicates how this approach may be further developed for application to established human and veterinary vaccines and emphasizes the continuing need for co-ordination and harmonization. It also gives recommendations for work to be undertaken in order to encourage acceptance and implementation of the consistency approach. Copyright © 2011. Published by Elsevier Ltd.. All rights reserved.

Real time monitoring of powder blend bulk density for coupled feed-forward/feed-back control of a continuous direct compaction tablet manufacturing process.

PubMed

Singh, Ravendra; Román-Ospino, Andrés D; Romañach, Rodolfo J; Ierapetritou, Marianthi; Ramachandran, Rohit

2015-11-10

The pharmaceutical industry is strictly regulated, where precise and accurate control of the end product quality is necessary to ensure the effectiveness of the drug products. For such control, the process and raw materials variability ideally need to be fed-forward in real time into an automatic control system so that a proactive action can be taken before it can affect the end product quality. Variations in raw material properties (e.g., particle size), feeder hopper level, amount of lubrication, milling and blending action, applied shear in different processing stages can affect the blend density significantly and thereby tablet weight, hardness and dissolution. Therefore, real time monitoring of powder bulk density variability and its incorporation into the automatic control system so that its effect can be mitigated proactively and efficiently is highly desired. However, real time monitoring of powder bulk density is still a challenging task because of different level of complexities. In this work, powder bulk density which has a significant effect on the critical quality attributes (CQA's) has been monitored in real time in a pilot-plant facility, using a NIR sensor. The sensitivity of the powder bulk density on critical process parameters (CPP's) and CQA's has been analyzed and thereby feed-forward controller has been designed. The measured signal can be used for feed-forward control so that the corrective actions on the density variations can be taken before they can influence the product quality. The coupled feed-forward/feed-back control system demonstrates improved control performance and improvements in the final product quality in the presence of process and raw material variations. Copyright © 2015 Elsevier B.V. All rights reserved.

Inverse simulation system for manual-controlled rendezvous and docking based on artificial neural network

NASA Astrophysics Data System (ADS)

Zhou, Wanmeng; Wang, Hua; Tang, Guojin; Guo, Shuai

2016-09-01

The time-consuming experimental method for handling qualities assessment cannot meet the increasing fast design requirements for the manned space flight. As a tool for the aircraft handling qualities research, the model-predictive-control structured inverse simulation (MPC-IS) has potential applications in the aerospace field to guide the astronauts' operations and evaluate the handling qualities more effectively. Therefore, this paper establishes MPC-IS for the manual-controlled rendezvous and docking (RVD) and proposes a novel artificial neural network inverse simulation system (ANN-IS) to further decrease the computational cost. The novel system was obtained by replacing the inverse model of MPC-IS with the artificial neural network. The optimal neural network was trained by the genetic Levenberg-Marquardt algorithm, and finally determined by the Levenberg-Marquardt algorithm. In order to validate MPC-IS and ANN-IS, the manual-controlled RVD experiments on the simulator were carried out. The comparisons between simulation results and experimental data demonstrated the validity of two systems and the high computational efficiency of ANN-IS.

In-flight investigation of the effects of pilot location and control system design on airplane flying qualities for approach and landing

NASA Technical Reports Server (NTRS)

Weingarten, N. C.; Chalk, C. R.

1982-01-01

The handling qualities of large airplanes in the approach and landing flight phase were studied. The primary variables were relative pilot position with respect to center of rotation, command path time delays and phase shifts, augmentation schemes and levels of augmentation. It is indicated that the approach and landing task with large airplanes is a low bandwidth task. Low equivalent short period frequencies and relatively long time delays are tolerated only when the pilot is located at considerable distance forward of the center of rotation. The control problem experienced by the pilots, when seated behind the center of rotation, tended to occur at low altitude when they were using visual cues of rate of sink and altitude. A direct lift controller improved final flight path control of the shuttle like configurations.

78 FR 54960 - Approval and Promulgation of Air Quality Implementation Plans; Massachusetts; Reasonably...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-09

... requirements of Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (15 U.S.C. 272... Technology for the 1997 8- Hour Ozone Standard AGENCY: Environmental Protection Agency (EPA). ACTION: Final... reasonably available control technology (RACT) for oxides of nitrogen (NO X ) and volatile organic compounds...

76 FR 34020 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Revisions to...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-10

... Department of Environmental Protection (PADEP). This change to Allegheny County's Air Pollution Control Rules... Rules section of this Federal Register, EPA is approving the State's SIP submittal as a direct final.... http://www.regulations.gov . Follow the online instructions for submitting comments. B. E-mail: cox...

78 FR 59258 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Withdrawal of Direct...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-26

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R03-OAR-2013-0058; FR-9901-21-Region3... Maintenance Area AGENCY: Environmental Protection Agency (EPA). ACTION: Withdrawal of direct final rule... Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Incorporation by reference...

Flood Control, Roseau River, Roseau and Kittson Counties, Minnesota. Final Environmental Impact Statement. Supplement.

DTIC Science & Technology

1981-09-01

business, and entrepreneur acquisition of presently marginal lands. The perceived result of withdrawal would be the shift of Roseau County from a com...impact statement (5S1) for this project we* plsed oa Eile witb the Council on Invironmenal Quality (CEQ) in April 1972. Because of incresing eaviromatal

77 FR 44146 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Control of Iron and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-27

... taking direct final action to approve revisions to the Maryland State Implementation Plan (SIP) submitted... steelmaking facility (Sparrows Point) is the only sintering plant located in the State of Maryland. The... emissions of particulate matter, continuously monitoring compliance with specified pressure drop and flow...

Control Strategy of Active Power Filter Based on Modular Multilevel Converter

NASA Astrophysics Data System (ADS)

Xie, Xifeng

2018-03-01

To improve the capacity, pressure resistance and the equivalent switching frequency of active power filter (APF), a control strategy of APF based on Modular Multilevel Converter (MMC) is presented. In this Control Strategy, the indirect current control method is used to achieve active current and reactive current decoupling control; Voltage Balance Control Strategy is to stabilize sub-module capacitor voltage, the predictive current control method is used to Track and control of harmonic currents. As a result, the harmonic current is restrained, and power quality is improved. Finally, the simulation model of active power filter controller based on MMC is established in Matlab/Simulink, the simulation proves that the proposed strategy is feasible and correct.

75 FR 33562 - Approval and Promulgation of Implementation Plans and Designations of Areas for Air Quality...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-14

...EPA is proposing to determine that the Birmingham, Alabama, nonattainment area for the 2006 24-hour fine particulate matter (PM2.5) National Ambient Air Quality Standard (NAAQS) has attained the 2006 24-hour PM2.5 NAAQS. This proposed determination is based upon complete, quality assured, quality controlled, and certified ambient air monitoring data for the years 2007-2009 showing that this area has monitored attainment of the 2006 24-hour PM2.5 NAAQS. If this proposed determination is made final, the requirement for the State of Alabama to submit an attainment demonstration and associated reasonably available control measures (RACM), reasonable further progress (RFP) plan, contingency measures, and other planning State Implementation Plans (SIPs) related to attainment of the 2006 24-hour PM2.5 standard for the Birmingham, Alabama, PM2.5 nonattainment area, shall be suspended for as long as this area continues to meet the 2006 24-hour PM2.5 NAAQS.

Hyperspectral imaging of water quality - past applications and future directions.

NASA Astrophysics Data System (ADS)

Ross, M. R. V.; Pavelsky, T.

2017-12-01

Inland waters control the delivery of sediment, carbon, and nutrients from land to ocean by transforming, depositing, and transporting constituents downstream. However, the dominant in situ conditions that control these processes are poorly constrained, especially at larger spatial scales. Hyperspectral imaging, a remote sensing technique that uses reflectance in hundreds of narrow spectral bands, can be used to estimate water quality parameters like sediment and carbon concentration over larger water bodies. Here, we review methods and applications for using hyperspectral imagery to generate near-surface two-dimensional models of water quality in lakes and rivers. Further, we show applications using newly available data from the National Ecological Observation Network aerial observation platform in the Black Warrior and Tombigbee Rivers, Alabama. We demonstrate large spatial variation in chlorophyll, colored dissolved organic matter, and turbidity in each river and uneven mixing of water quality constituents for several kilometers. Finally, we demonstrate some novel techniques using hyperspectral imagery to deconvolve dissolved organic matter spectral signatures to specific organic matter components.

Quality competition and hospital mergers-An experiment.

PubMed

Han, Johann; Kairies-Schwarz, Nadja; Vomhof, Markus

2017-12-01

On the basis of a Salop model with regulated prices, we investigate quality provision behaviour of competing hospitals before and after a merger. For this, we use a controlled laboratory experiment where subjects decided on the level of treatment quality as head of a hospital. We find that the post-merger average quality is significantly lower than the average pre-merger quality. However, for merger insiders and outsiders, average quality choices are significantly higher than predicted for pure profit-maximising hospitals. This upward deviation is potentially driven by altruistic behaviour towards patients. Furthermore, we find that in the case where sufficient cost synergies are realised by the merged hospitals, there is a significant increase in average quality choices compared to the scenario without synergies. Finally, we find that our results do not change when comparing individual decisions to team decisions. Copyright © 2017 John Wiley & Sons, Ltd.

76 FR 28944 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-19

...EPA is proposing a limited approval and limited disapproval of permitting rules submitted for the Placer County Air Pollution Control District (PCAPCD) and Feather River Air Quality Management District (FRAQMD) portion of the California State Implementation Plan (SIP). The districts are required under Part D of title I of the Clean Air Act (CAA) to adopt and implement a SIP-approved New Source Review (NSR) permit program. These rules update and revise the District's NSR permitting program for new and modified sources of air pollution. If EPA finalizes the limited approval and limited disapproval action, as proposed, then a sanctions clock would be triggered. We are taking comments on this proposal and plan to follow with a final action.

Screening bioactive quality control markers of QiShenYiQi dripping pills based on the relationship between the ultra-high performance liquid chromatography fingerprint and vascular protective activity.

PubMed

Zhuo, Limeng; Peng, Jingjing; Zhao, Yunli; Li, Dongxiang; Xie, Xiuman; Tong, Ling; Yu, Zhiguo

2017-10-01

Traditional Chinese medicine consists of complex phytochemical constituents. Selecting appropriate analytical markers of traditional Chinese medicine is a critical step in quality control. Currently, the combination of fingerprinting and efficacy evaluation is considered as a useful method for screening active ingredients in complex mixtures. This study was designed to develop an orthogonal partial least squares model for screening bioactive quality control markers of QishenYiqi dripping pills based on the fingerprint-efficacy relationship. First, the chemical fingerprints of 49 batches of QishenYiqi dripping pill samples were established by ultra-high performance liquid chromatography coupled with a photodiode array detector. Second, ultra-high performance liquid chromatography coupled with quadrupole-time-of-flight mass spectrometry was exploited to systematically investigate the 36 copossessing fingerprint components in QishenYiqi dripping pills. The vascular protective activity of QishenYiqi dripping pills was determined by using a cell counting kit-8 assay. Finally, fingerprint-efficacy relationship was established by orthogonal partial least squares model. The results indicated that ten components exhibited strong correlation with vascular protective activity, and these were preliminarily screened as quality control markers. The present study provided a novel idea for the study of the pharmacodynamic material basis and quality evaluation of QishenYiqi dripping pills. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Data Assimilation Experiments using Quality Controlled AIRS Version 5 Temperature Soundings

NASA Technical Reports Server (NTRS)

Susskind, Joel

2008-01-01

The AIRS Science Team Version 5 retrieval algorithm has been finalized and is now operational at the Goddard DAAC in the processing (and reprocessing) of all AlRS data. Version 5 contains accurate case-by-case error estimates for most derived products, which are also used for quality control. We have conducted forecast impact experiments assimilating AlRS quality controlled temperature profiles using the NASA GEOS-5 data assimilation system, consisting of the NCEP GSI analysis coupled with the NASA FVGCM. Assimilation of quality controlled temperature profiles resulted in significantly improved forecast skill in both the Northern Hemisphere and Southern Hemisphere Extra-Tropics, compared to that obtained from analyses obtained when all data used operationally by NCEP except for AlRS data is assimilated. Experiments using different Quality Control thresholds for assimilation of AlRS temperature retrievals showed that a medium quality control threshold performed better than a tighter threshold, which provided better overall sounding accuracy; or a looser threshold, which provided better spatial coverage of accepted soundings. We are conducting more experiments to further optimize this balance of spatial coverage and sounding accuracy from the data assimilation perspective. In all cases, temperature soundings were assimilated well below cloud level in partially cloudy cases. The positive impact of assimilating AlRS derived atmospheric temperatures all but vanished when only AIRS stratospheric temperatures were assimilated. Forecast skill resulting from assimilation of AlRS radiances uncontaminated by clouds, instead of AlRS temperature soundings, was only slightly better than that resulting from assimilation of only stratospheric AlRS temperatures. This reduction in forecast skill is most likely the result of significant loss of tropospheric information when only AIRS radiances unaffected by clouds are used in the data assimilation process.

The Relationship Between Reported Sleep Quality and Sleep Hygiene in Italian and American Adolescents

PubMed Central

LeBourgeois, Monique K.; Giannotti, Flavia; Cortesi, Flavia; Wolfson, Amy R.; Harsh, John

2014-01-01

Objective The purpose of the study was to examine the relationship between self-reported sleep quality and sleep hygiene in Italian and American adolescents and to assess whether sleep-hygiene practices mediate the relationship between culture and sleep quality. Methods Two nonprobability samples were collected from public schools in Rome, Italy, and Hattiesburg, Mississippi. Students completed the following self-report measures: Adolescent Sleep-Wake Scale, Adolescent Sleep Hygiene Scale, Pubertal Developmental Scale, and Morningness/Eveningness Scale. Results The final sample included 776 Italian and 572 American adolescents 12 to 17 years old. Italian adolescents reported much better sleep hygiene and substantially better sleep quality than American adolescents. A moderate-to-strong linear relationship was found between sleep hygiene and sleep quality in both samples. Separate hierarchical multiple regression analyses were performed on both samples. Demographic and individual characteristics explained a significant proportion of the variance in sleep quality (Italians: 18%; Americans: 25%), and the addition of sleep-hygiene domains explained significantly more variance in sleep quality (Italians: 17%; Americans: 16%). A final hierarchical multiple regression analysis with both samples combined showed that culture (Italy versus United States) only explained 0.8% of the variance in sleep quality after controlling for sleep hygiene and all other variables. Conclusions Cross-cultural differences in sleep quality, for the most part, were due to differences in sleep-hygiene practices. Sleep hygiene is an important predictor of sleep quality in Italian and American adolescents, thus supporting the implementation and evaluation of educational programs on good sleep-hygiene practices. PMID:15866860

Taguchi Method Applied in Optimization of Shipley SJR 5740 Positive Resist Deposition

NASA Technical Reports Server (NTRS)

Hui, A.; Blosiu, J. O.; Wiberg, D. V.

1998-01-01

Taguchi Methods of Robust Design presents a way to optimize output process performance through an organized set of experiments by using orthogonal arrays. Analysis of variance and signal-to-noise ratio is used to evaluate the contribution of each of the process controllable parameters in the realization of the process optimization. In the photoresist deposition process, there are numerous controllable parameters that can affect the surface quality and thickness of the final photoresist layer.

Final Base Realignment and Closure (BRAC) Environmental Assessment for Realignment of Nellis Air Force Base

DTIC Science & Technology

2007-03-01

Traffic Control Assigned Airspace ATG Adversary Tactics Group AWACS Airborne Warning and Control System BAQ Bureau of Air Quality BLM Bureau of Land...Department of Interior Actions BLM The BLM manages millions of acres of public lands in southern Nevada which include portions of NTTR and...within NTTR and would not affect BLM lands adjacent to the base. Therefore, there are no cumulative impacts. USFWS Aircraft operate within the

Electronic Noses and Tongues in Wine Industry

PubMed Central

Rodríguez-Méndez, María L.; De Saja, José A.; González-Antón, Rocio; García-Hernández, Celia; Medina-Plaza, Cristina; García-Cabezón, Cristina; Martín-Pedrosa, Fernando

2016-01-01

The quality of wines is usually evaluated by a sensory panel formed of trained experts or traditional chemical analysis. Over the last few decades, electronic noses (e-noses) and electronic tongues have been developed to determine the quality of foods and beverages. They consist of arrays of sensors with cross-sensitivity, combined with pattern recognition software, which provide a fingerprint of the samples that can be used to discriminate or classify the samples. This holistic approach is inspired by the method used in mammals to recognize food through their senses. They have been widely applied to the analysis of wines, including quality control, aging control, or the detection of fraudulence, among others. In this paper, the current status of research and development in the field of e-noses and tongues applied to the analysis of wines is reviewed. Their potential applications in the wine industry are described. The review ends with a final comment about expected future developments. PMID:27826547

Comparison of answer-until-correct and full-credit assessments in a team-based learning course.

PubMed

Farland, Michelle Z; Barlow, Patrick B; Levi Lancaster, T; Franks, Andrea S

2015-03-25

To assess the impact of awarding partial credit to team assessments on team performance and on quality of team interactions using an answer-until-correct method compared to traditional methods of grading (multiple-choice, full-credit). Subjects were students from 3 different offerings of an ambulatory care elective course, taught using team-based learning. The control group (full-credit) consisted of those enrolled in the course when traditional methods of assessment were used (2 course offerings). The intervention group consisted of those enrolled in the course when answer-until-correct method was used for team assessments (1 course offering). Study outcomes included student performance on individual and team readiness assurance tests (iRATs and tRATs), individual and team final examinations, and student assessment of quality of team interactions using the Team Performance Scale. Eighty-four students enrolled in the courses were included in the analysis (full-credit, n=54; answer-until-correct, n=30). Students who used traditional methods of assessment performed better on iRATs (full-credit mean 88.7 (5.9), answer-until-correct mean 82.8 (10.7), p<0.001). Students who used answer-until-correct method of assessment performed better on the team final examination (full-credit mean 45.8 (1.5), answer-until-correct 47.8 (1.4), p<0.001). There was no significant difference in performance on tRATs and the individual final examination. Students who used the answer-until-correct method had higher quality of team interaction ratings (full-credit 97.1 (9.1), answer-until-correct 103.0 (7.8), p=0.004). Answer-until-correct assessment method compared to traditional, full-credit methods resulted in significantly lower scores for iRATs, similar scores on tRATs and individual final examinations, improved scores on team final examinations, and improved perceptions of the quality of team interactions.

Changes in the Microbial Composition of Microbrewed Beer during the Process in the Actual Manufacturing Line.

PubMed

Kim, S A; Jeon, S H; Kim, N H; Kim, H W; Lee, N Y; Cho, T J; Jung, Y M; Lee, S H; Hwang, I G; Rhee, M S

2015-12-01

This study investigated changes in the microbial composition of microbrewed beer during the manufacturing processes and identified potential microbial hazards, effective critical quality control points, and potential contamination routes. Comprehensive quantitative (aerobic plate count, lactic acid bacteria, fungi, acetic acid bacteria, coliforms, and Bacillus cereus) and qualitative (Escherichia coli and eight foodborne pathogens) microbiological analyses were performed using samples of raw materials (malt and manufacturing water), semiprocessed products (saccharified wort, boiled wort, and samples taken during the fermentation and maturation process), and the final product obtained from three plants. The initial aerobic plate count and lactic acid bacteria counts in malt were 5.2 and 4.3 log CFU/g, respectively. These counts were reduced to undetectable levels by boiling but were present at 2.9 and 0.9 log CFU/ml in the final product. Fungi were initially present at 3.6 log CFU/g, although again, the microbes were eliminated by boiling; however, the level in the final product was 4.6 log CFU/ml. No E. coli or foodborne pathogens (except B. cereus) were detected. B. cereus was detected at all stages, although it was not present in the water or boiled wort (total detection rate ¼ 16.4%). Results suggest that boiling of the wort is an effective microbial control measure, but careful management of raw materials and implementation of effective control measures after boiling are needed to prevent contamination of the product after the boiling step. The results of this study may constitute useful and comprehensive information regarding the microbiological quality of microbrewed beer.

Assessment of 100% Rapid Review as an Effective Tool for Internal Quality Control in Cytopathological Services.

PubMed

Queiroz Filho, José; de Oliveira Crispim Freitas, Janaina Cristiana; Caldas Pessoa, Daliana; Eleutério Júnior, José; Giraldo, Paulo César; Gonçalves, Ana Katherine

2017-01-01

The aim of this study was to evaluate the 100% rapid review (100%-RR) as an effective tool for internal quality control (IQC) in gynecological cytopathology services. A total of 8,677 swabs were analyzed; the negative results were submitted to 100%-RR. Divergent cases were discussed in a consensus meeting to reach a conclusion on the final diagnosis. The data were entered into SAS statistical software, and the agreement of the 100%-RR results with the final diagnosis was tested with the weighted kappa statistic. Of the 8,155 smears characterized as negative, 255 (3.13%) were abnormal smears, and 552 (6.77%) unsatisfactory smears were deemed negative. Regarding the results on the 8,155 smears subjected to 100%-RR when compared with the final diagnosis, there was agreement in 7,063 (86.60%) of them, and there were 1,092 (13.40%) discordant results (65.6%, unsatisfactory; 5.47%, atypical squamous cells of undetermined significance [ASC-US]). The κ index had an agreement of 0.867, with κ = 0.734 (p < 0.0001). Compared with the final diagnosis, the sensitivity of 100%-RR was 99.91% and its specificity was 99.4% for severe abnormalities. The sensitivity for high-grade squamous intraepithelial lesions was 88.2%, with a specificity of 100.00%. For abnormalities considered borderline, such as ASC-US, the sensitivity was 94.50% and the specificity was 99.5%. The 100%-RR was considered efficient when used as an IQC method. © 2017 S. Karger AG, Basel.

The European general thoracic surgery database project.

PubMed

Falcoz, Pierre Emmanuel; Brunelli, Alessandro

2014-05-01

The European Society of Thoracic Surgeons (ESTS) Database is a free registry created by ESTS in 2001. The current online version was launched in 2007. It runs currently on a Dendrite platform with extensive data security and frequent backups. The main features are a specialty-specific, procedure-specific, prospectively maintained, periodically audited and web-based electronic database, designed for quality control and performance monitoring, which allows for the collection of all general thoracic procedures. Data collection is the "backbone" of the ESTS database. It includes many risk factors, processes of care and outcomes, which are specially designed for quality control and performance audit. The user can download and export their own data and use them for internal analyses and quality control audits. The ESTS database represents the gold standard of clinical data collection for European General Thoracic Surgery. Over the past years, the ESTS database has achieved many accomplishments. In particular, the database hit two major milestones: it now includes more than 235 participating centers and 70,000 surgical procedures. The ESTS database is a snapshot of surgical practice that aims at improving patient care. In other words, data capture should become integral to routine patient care, with the final objective of improving quality of care within Europe.

Opportunities and challenges of real-time release testing in biopharmaceutical manufacturing.

PubMed

Jiang, Mo; Severson, Kristen A; Love, John Christopher; Madden, Helena; Swann, Patrick; Zang, Li; Braatz, Richard D

2017-11-01

Real-time release testing (RTRT) is defined as "the ability to evaluate and ensure the quality of in-process and/or final drug product based on process data, which typically includes a valid combination of measured material attributes and process controls" (ICH Q8[R2]). This article discusses sensors (process analytical technology, PAT) and control strategies that enable RTRT for the spectrum of critical quality attributes (CQAs) in biopharmaceutical manufacturing. Case studies from the small-molecule and biologic pharmaceutical industry are described to demonstrate how RTRT can be facilitated by integrated manufacturing and multivariable control strategies to ensure the quality of products. RTRT can enable increased assurance of product safety, efficacy, and quality-with improved productivity including faster release and potentially decreased costs-all of which improve the value to patients. To implement a complete RTRT solution, biologic drug manufacturers need to consider the special attributes of their industry, particularly sterility and the measurement of viral and microbial contamination. Continued advances in on-line and in-line sensor technologies are key for the biopharmaceutical manufacturing industry to achieve the potential of RTRT. Related article: http://onlinelibrary.wiley.com/doi/10.1002/bit.26378/full. © 2017 Wiley Periodicals, Inc.

Sodium Dichloroisocyanurate Tablets for Routine Treatment of Household Drinking Water in Periurban Ghana: A Randomized Controlled Trial

PubMed Central

Jain, Seema; Sahanoon, Osman K.; Blanton, Elizabeth; Schmitz, Ann; Wannemuehler, Kathleen A.; Hoekstra, Robert M.; Quick, Robert E.

2010-01-01

We conducted a randomized, placebo-controlled, triple-blinded trial to determine the health impact of daily use of sodium dichloroisocyanurate (NaDCC) tablets for household drinking water treatment in periurban Ghana. We randomized 240 households (3,240 individuals) to receive either NaDCC or placebo tablets. All households received a 20-liter safe water storage vvessel. Over 12 weeks, 446 diarrhea episodes (2.2%) occurred in intervention and 404 (2.0%) in control households (P = 0.38). Residual free chlorine levels indicated appropriate tablet use. Escherichia coli was found in stored water at baseline in 96% of intervention and 88% of control households and at final evaluation in 8% of intervention and 54% of control households (P = 0.002). NaDCC use did not prevent diarrhea but improved water quality. Diarrhea rates were low and water quality improved in both groups. Safe water storage vessels may have been protective. A follow-up health impact study of NaDCC tablets is warranted. PMID:20064989

Advancing Understanding of Emissions from Oil and Natural Gas Production Operations to Support EPA’s Air Quality Modeling of Ozone Non-Attainment Areas; Final Summary Report

EPA Science Inventory

Executive Summary Environmentally responsible development of oil and gas assets requires well-developed emissions inventories and measurement techniques to verify emissions and the effectiveness of control strategies. To accurately model the oil and gas sector impacts on air qual...

76 FR 29649 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-23

... global warming, through regulations that will harm the economy of the United States,'' and asserts that EPA is attempting to take such action on the issue of global warming which Congress has ``decided that... purpose of addressing global warming. IV. Final Action EPA is approving Pennsylvania's adoption of the CTG...

Public Policies and Suicide Rates in the American States

ERIC Educational Resources Information Center

Flavin, Patrick; Radcliff, Benjamin

2009-01-01

We are interested in the relationship between public policies and outcomes measuring quality of life. There is no outcome more final than the ending of one's own life. Accordingly, we test the relationship between public policy regimes and suicide rates in the American states. Controlling for other relevant factors (most notably a state's stock of…

75 FR 6307 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Control of Carbon...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-09

... Oxygen Furnaces AGENCY: Environmental Protection Agency (EPA). ACTION: Direct final rule. SUMMARY: EPA is... carbon monoxide (CO) emissions from basic oxygen furnaces (BOFs) at steel mills in the State of Maryland... blast furnace and scrap metal which is heated with oxygen to produce molten metal. The molten metal is...

[Analytical quality in biological monitoring of workers exposed to chemicals: experience of the Prevention and Safety at the Workplace Service in Modena].

PubMed

Alpaca, R I Paredes; Migliore, A; Di Rico, R; Canali, Claudia; Rota, Cristina; Trenti, T; Cariani, Elisabetta

2010-01-01

The quality of laboratory data is one of the main factors in guaranteeing efficacy of biological monitoring. To analyze the quality of laboratory data used for biological monitoring of exposed workers. A survey involving 18 companies employing 945 workers in the area of Modena, Italy, was carried out in 2008. Most of the 9 private laboratories receiving biological samples did not perform directly part or all of the laboratory assessments requested, but this was not indicated in the final report. Major problems were observed in the application of internal quality control, and only one laboratory participated in external quality assessment for blood lead measurements. Our results raise major concerns on the traceability and reliability of laboratory assessments performed for biomonitoring of exposed workers. Systematic evaluation of the quality of analytical data would be highly recommendable.

Optimal shifting control strategy in inertia phase of an automatic transmission for automotive applications

NASA Astrophysics Data System (ADS)

Meng, Fei; Tao, Gang; Zhang, Tao; Hu, Yihuai; Geng, Peng

2015-08-01

Shifting quality is a crucial factor in all parts of the automobile industry. To ensure an optimal gear shifting strategy with best fuel economy for a stepped automatic transmission, the controller should be designed to meet the challenge of lacking of a feedback sensor to measure the relevant variables. This paper focuses on a new kind of automatic transmission using proportional solenoid valve to control the clutch pressure, a speed difference of the clutch based control strategy is designed for the shift control during the inertia phase. First, the mechanical system is shown and the system dynamic model is built. Second, the control strategy is designed based on the characterization analysis of models which are derived from dynamics of the drive line and electro-hydraulic actuator. Then, the controller uses conventional Proportional-Integral-Derivative control theory, and a robust two-degree-of-freedom controller is also carried out to determine the optimal control parameters to further improve the system performance. Finally, the designed control strategy with different controller is implemented on a simulation model. The compared results show that the speed difference of clutch can track the desired trajectory well and improve the shift quality effectively.

Working conditions, self-perceived stress, anxiety, depression and quality of life: A structural equation modelling approach

PubMed Central

Rusli, Bin Nordin; Edimansyah, Bin Abdin; Naing, Lin

2008-01-01

Background The relationships between working conditions [job demand, job control and social support]; stress, anxiety, and depression; and perceived quality of life factors [physical health, psychological wellbeing, social relationships and environmental conditions] were assessed using a sample of 698 male automotive assembly workers in Malaysia. Methods The validated Malay version of the Job Content Questionnaire (JCQ), Depression Anxiety Stress Scales (DASS) and the World Health Organization Quality of Life-Brief (WHOQOL-BREF) were used. A structural equation modelling (SEM) analysis was applied to test the structural relationships of the model using AMOS version 6.0, with the maximum likelihood ratio as the method of estimation. Results The results of the SEM supported the hypothesized structural model (χ2 = 22.801, df = 19, p = 0.246). The final model shows that social support (JCQ) was directly related to all 4 factors of the WHOQOL-BREF and inversely related to depression and stress (DASS). Job demand (JCQ) was directly related to stress (DASS) and inversely related to the environmental conditions (WHOQOL-BREF). Job control (JCQ) was directly related to social relationships (WHOQOL-BREF). Stress (DASS) was directly related to anxiety and depression (DASS) and inversely related to physical health, environment conditions and social relationships (WHOQOL-BREF). Anxiety (DASS) was directly related to depression (DASS) and inversely related to physical health (WHOQOL-BREF). Depression (DASS) was inversely related to the psychological wellbeing (WHOQOL-BREF). Finally, stress, anxiety and depression (DASS) mediate the relationships between job demand and social support (JCQ) to the 4 factors of WHOQOL-BREF. Conclusion These findings suggest that higher social support increases the self-reported quality of life of these workers. Higher job control increases the social relationships, whilst higher job demand increases the self-perceived stress and decreases the self-perceived quality of life related to environmental factors. The mediating role of depression, anxiety and stress on the relationship between working conditions and perceived quality of life in automotive workers should be taken into account in managing stress amongst these workers. PMID:18254966

Working conditions, self-perceived stress, anxiety, depression and quality of life: a structural equation modelling approach.

PubMed

Rusli, Bin Nordin; Edimansyah, Bin Abdin; Naing, Lin

2008-02-06

The relationships between working conditions [job demand, job control and social support]; stress, anxiety, and depression; and perceived quality of life factors [physical health, psychological wellbeing, social relationships and environmental conditions] were assessed using a sample of 698 male automotive assembly workers in Malaysia. The validated Malay version of the Job Content Questionnaire (JCQ), Depression Anxiety Stress Scales (DASS) and the World Health Organization Quality of Life-Brief (WHOQOL-BREF) were used. A structural equation modelling (SEM) analysis was applied to test the structural relationships of the model using AMOS version 6.0, with the maximum likelihood ratio as the method of estimation. The results of the SEM supported the hypothesized structural model (chi2 = 22.801, df = 19, p = 0.246). The final model shows that social support (JCQ) was directly related to all 4 factors of the WHOQOL-BREF and inversely related to depression and stress (DASS). Job demand (JCQ) was directly related to stress (DASS) and inversely related to the environmental conditions (WHOQOL-BREF). Job control (JCQ) was directly related to social relationships (WHOQOL-BREF). Stress (DASS) was directly related to anxiety and depression (DASS) and inversely related to physical health, environment conditions and social relationships (WHOQOL-BREF). Anxiety (DASS) was directly related to depression (DASS) and inversely related to physical health (WHOQOL-BREF). Depression (DASS) was inversely related to the psychological wellbeing (WHOQOL-BREF). Finally, stress, anxiety and depression (DASS) mediate the relationships between job demand and social support (JCQ) to the 4 factors of WHOQOL-BREF. These findings suggest that higher social support increases the self-reported quality of life of these workers. Higher job control increases the social relationships, whilst higher job demand increases the self-perceived stress and decreases the self-perceived quality of life related to environmental factors. The mediating role of depression, anxiety and stress on the relationship between working conditions and perceived quality of life in automotive workers should be taken into account in managing stress amongst these workers.

Quality dependent fusion of intramodal and multimodal biometric experts

NASA Astrophysics Data System (ADS)

Kittler, J.; Poh, N.; Fatukasi, O.; Messer, K.; Kryszczuk, K.; Richiardi, J.; Drygajlo, A.

2007-04-01

We address the problem of score level fusion of intramodal and multimodal experts in the context of biometric identity verification. We investigate the merits of confidence based weighting of component experts. In contrast to the conventional approach where confidence values are derived from scores, we use instead raw measures of biometric data quality to control the influence of each expert on the final fused score. We show that quality based fusion gives better performance than quality free fusion. The use of quality weighted scores as features in the definition of the fusion functions leads to further improvements. We demonstrate that the achievable performance gain is also affected by the choice of fusion architecture. The evaluation of the proposed methodology involves 6 face and one speech verification experts. It is carried out on the XM2VTS data base.

HadISD: a quality-controlled global synoptic report database for selected variables at long-term stations from 1973-2011

NASA Astrophysics Data System (ADS)

Dunn, R. J. H.; Willett, K. M.; Thorne, P. W.; Woolley, E. V.; Durre, I.; Dai, A.; Parker, D. E.; Vose, R. S.

2012-10-01

This paper describes the creation of HadISD: an automatically quality-controlled synoptic resolution dataset of temperature, dewpoint temperature, sea-level pressure, wind speed, wind direction and cloud cover from global weather stations for 1973-2011. The full dataset consists of over 6000 stations, with 3427 long-term stations deemed to have sufficient sampling and quality for climate applications requiring sub-daily resolution. As with other surface datasets, coverage is heavily skewed towards Northern Hemisphere mid-latitudes. The dataset is constructed from a large pre-existing ASCII flatfile data bank that represents over a decade of substantial effort at data retrieval, reformatting and provision. These raw data have had varying levels of quality control applied to them by individual data providers. The work proceeded in several steps: merging stations with multiple reporting identifiers; reformatting to netCDF; quality control; and then filtering to form a final dataset. Particular attention has been paid to maintaining true extreme values where possible within an automated, objective process. Detailed validation has been performed on a subset of global stations and also on UK data using known extreme events to help finalise the QC tests. Further validation was performed on a selection of extreme events world-wide (Hurricane Katrina in 2005, the cold snap in Alaska in 1989 and heat waves in SE Australia in 2009). Some very initial analyses are performed to illustrate some of the types of problems to which the final data could be applied. Although the filtering has removed the poorest station records, no attempt has been made to homogenise the data thus far, due to the complexity of retaining the true distribution of high-resolution data when applying adjustments. Hence non-climatic, time-varying errors may still exist in many of the individual station records and care is needed in inferring long-term trends from these data. This dataset will allow the study of high frequency variations of temperature, pressure and humidity on a global basis over the last four decades. Both individual extremes and the overall population of extreme events could be investigated in detail to allow for comparison with past and projected climate. A version-control system has been constructed for this dataset to allow for the clear documentation of any updates and corrections in the future.

A QRM Discussion of Microbial Contamination of Non-sterile Drug Products, Using FDA and EMA Warning Letters Recorded between 2008 and 2016.

PubMed

Santos, Ana M C; Doria, Mara S; Meirinhos-Soares, Luís; Almeida, António J; Menezes, José C

2018-01-01

Microbial quality control of non-sterile drug products has been a concern to regulatory agencies and the pharmaceutical industry since the 1960s. Despite being an old challenge to companies, microbial contamination still affects a high number of manufacturers of non-sterile products. Consequences go well beyond the obvious direct costs related to batch rejections or product recalls, as human lives and a company's reputation are significantly impacted if such events occur. To better manage risk and establish effective mitigation strategies, it is necessary to understand the microbial hazards involved in non-sterile drug products manufacturing, be able to evaluate their potential impact on final product quality, and apply mitigation actions. Herein we discuss the most likely root causes involved in microbial contaminations referenced in warning letters issued by US health authorities and non-compliance reports issued by European health authorities over a period of several years. The quality risk management tools proposed were applied to the data gathered from those databases, and a generic risk ranking was provided based on a panel of non-sterile drug product manufacturers that was assembled and given the opportunity to perform the risk assessments. That panel identified gaps and defined potential mitigation actions, based on their own experience of potential risks expected for their processes. Major findings clearly indicate that the manufacturers affected by the warning letters should focus their attention on process improvements and microbial control strategies, especially those related to microbial analysis and raw material quality control. Additionally, the WLs considered frequently referred to failures in quality-related issues, which indicates that the quality commitment should be reinforced at most companies to avoid microbiological contaminations. LAY ABSTRACT: Microbial contamination of drug products affects the quality of non-sterile drug products produced by numerous manufacturers, representing a major risk to patients. It is necessary to understand the microbial hazards involved in the manufacturing process and evaluate their impact on final product quality so that effective prevention strategies can be implemented. A risk-based classification of most likely root causes for microbial contamination found in the warning letters issued by the US Food and Drug Administration and the European Medicines Agency is proposed. To validate the likely root causes extracted from the warning letters, a subject matter expert panel made of several manufacturers was formed and consulted. A quality risk management approach to assess microbiological contamination of non-sterile drug products is proposed for the identification of microbial hazards involved in the manufacturing process. To enable ranking of microbial contamination risks, quality risk management metrics related to criticality and overall risk were applied. The results showed that manufacturers of non-sterile drug products should improve their microbial control strategy, with special attention to quality controls of raw materials, primary containers, and closures. Besides that, they should invest in a more robust quality system and culture. As a start, manufacturers may consider investigating their specific microbiological risks, adressing their sites' own microbial ecology, type of manufacturing processes, and dosage form characteristics, as these may lead to increased contamination risks. Authorities should allow and enforce innovative, more comprehensive, and more effective approaches to in-process contamination monitoring and controls. © PDA, Inc. 2018.

Direct energy balance based active disturbance rejection control for coal-fired power plant.

PubMed

Sun, Li; Hua, Qingsong; Li, Donghai; Pan, Lei; Xue, Yali; Lee, Kwang Y

2017-09-01

The conventional direct energy balance (DEB) based PI control can fulfill the fundamental tracking requirements of the coal-fired power plant. However, it is challenging to deal with the cases when the coal quality variation is present. To this end, this paper introduces the active disturbance rejection control (ADRC) to the DEB structure, where the coal quality variation is deemed as a kind of unknown disturbance that can be estimated and mitigated promptly. Firstly, the nonlinearity of a recent power plant model is analyzed based on the gap metric, which provides guidance on how to set the pressure set-point in line with the power demand. Secondly, the approximate decoupling effect of the DEB structure is analyzed based on the relative gain analysis in frequency domain. Finally, the synthesis of the DEB based ADRC control system is carried out based on multi-objective optimization. The optimized ADRC results show that the integrated absolute error (IAE) indices of the tracking performances in both loops can be simultaneously improved, in comparison with the DEB based PI control and H ∞ control system. The regulation performance in the presence of the coal quality variation is significantly improved under the ADRC control scheme. Moreover, the robustness of the proposed strategy is shown comparable with the H ∞ control. Copyright © 2017. Published by Elsevier Ltd.

The Influence of Parental Control and Parent-Child Relational Qualities on Adolescent Internet Addiction: A 3-Year Longitudinal Study in Hong Kong

PubMed Central

Shek, Daniel T. L.; Zhu, Xiaoqin; Ma, Cecilia M. S.

2018-01-01

This study investigated how parental behavioral control, parental psychological control, and parent-child relational qualities predicted the initial level and rate of change in adolescent internet addiction (IA) across the junior high school years. The study also investigated the concurrent and longitudinal effects of different parenting factors on adolescent IA. Starting from the 2009/2010 academic year, 3,328 Grade 7 students (Mage = 12.59 ± 0.74 years) from 28 randomly selected secondary schools in Hong Kong responded on a yearly basis to a questionnaire measuring multiple constructs including socio-demographic characteristics, perceived parenting characteristics, and IA. Individual growth curve (IGC) analyses showed that adolescent IA slightly decreased during junior high school years. While behavioral control of both parents was negatively related to the initial level of adolescent IA, only paternal behavioral control showed a significant positive relationship with the rate of linear change in IA, suggesting that higher paternal behavioral control predicted a slower decrease in IA. In addition, fathers' and mothers' psychological control was positively associated with the initial level of adolescent IA, but increase in maternal psychological control predicted a faster drop in IA. Finally, parent-child relational qualities negatively and positively predicted the initial level and the rate of change in IA, respectively. When all parenting factors were considered simultaneously, multiple regression analyses revealed that paternal behavioral control and psychological control as well as maternal psychological control and mother-child relational quality were significant concurrent predictors of adolescent IA at Wave 2 and Wave 3. Regarding the longitudinal predicting effects, paternal psychological control and mother-child relational quality at Wave 1 were the two most robust predictors of later adolescent IA at Wave 2 and Wave 3. The above findings underscore the importance of the parent-child subsystem qualities in influencing adolescent IA in the junior high school years. In particular, these findings shed light on the different impacts of fathering and mothering which are neglected in the scientific literature. While the findings based on the levels of IA are consistent with the existing theoretical models, findings on the rate of change are novel. PMID:29765349

The Influence of Parental Control and Parent-Child Relational Qualities on Adolescent Internet Addiction: A 3-Year Longitudinal Study in Hong Kong.

PubMed

Shek, Daniel T L; Zhu, Xiaoqin; Ma, Cecilia M S

2018-01-01

This study investigated how parental behavioral control, parental psychological control, and parent-child relational qualities predicted the initial level and rate of change in adolescent internet addiction (IA) across the junior high school years. The study also investigated the concurrent and longitudinal effects of different parenting factors on adolescent IA. Starting from the 2009/2010 academic year, 3,328 Grade 7 students ( M age = 12.59 ± 0.74 years) from 28 randomly selected secondary schools in Hong Kong responded on a yearly basis to a questionnaire measuring multiple constructs including socio-demographic characteristics, perceived parenting characteristics, and IA. Individual growth curve (IGC) analyses showed that adolescent IA slightly decreased during junior high school years. While behavioral control of both parents was negatively related to the initial level of adolescent IA, only paternal behavioral control showed a significant positive relationship with the rate of linear change in IA, suggesting that higher paternal behavioral control predicted a slower decrease in IA. In addition, fathers' and mothers' psychological control was positively associated with the initial level of adolescent IA, but increase in maternal psychological control predicted a faster drop in IA. Finally, parent-child relational qualities negatively and positively predicted the initial level and the rate of change in IA, respectively. When all parenting factors were considered simultaneously, multiple regression analyses revealed that paternal behavioral control and psychological control as well as maternal psychological control and mother-child relational quality were significant concurrent predictors of adolescent IA at Wave 2 and Wave 3. Regarding the longitudinal predicting effects, paternal psychological control and mother-child relational quality at Wave 1 were the two most robust predictors of later adolescent IA at Wave 2 and Wave 3. The above findings underscore the importance of the parent-child subsystem qualities in influencing adolescent IA in the junior high school years. In particular, these findings shed light on the different impacts of fathering and mothering which are neglected in the scientific literature. While the findings based on the levels of IA are consistent with the existing theoretical models, findings on the rate of change are novel.

Limited Qualities Evaluation of Longitudinal Flight Control Systems Designed Using Multiobjective Control Design Techniques (HAVE INFINITY II)

DTIC Science & Technology

1998-06-01

analytical phase of this research. Finally, the mixed H2/H-Infinity method optimally tradeoff the different benefits offered by the separate H2 and H...potential benefits of the multiobjective design techniques used. Due to the HAVE INFINITY I test results, AFIT made the decision to continue the...sensitivity and complimentary sensitivity weighting, and a mixed H2/H-Infinity design that compromised the benefits of both design techniques optimally. The

Implementation of the Diabetes Practice Guideline in the Army Medical Department: Final Evaluation

DTIC Science & Technology

2005-01-01

Diabetes Quality Improvement Project DRG Diagnosis-Related Group ER Emergency room FMP Family Member Prefix HBA1c Hemoglobin A1c HCSR Health-Care Service...glycemic control by assessing and managing glycosylated hemoglobin, reported as hemoglobin A1c ( HbA1c ) lev- els. Assess HbA1c levels relative to target...frequency involved in adjusting insulin dosages Increase in the percentage of noninsulin patients who fill prescribed medications to control HbA1c

Acetic Acid Bacteria and the Production and Quality of Wine Vinegar

PubMed Central

Torija, María Jesús; García-Parrilla, María del Carmen; Troncoso, Ana María

2014-01-01

The production of vinegar depends on an oxidation process that is mainly performed by acetic acid bacteria. Despite the different methods of vinegar production (more or less designated as either “fast” or “traditional”), the use of pure starter cultures remains far from being a reality. Uncontrolled mixed cultures are normally used, but this review proposes the use of controlled mixed cultures. The acetic acid bacteria species determine the quality of vinegar, although the final quality is a combined result of technological process, wood contact, and aging. This discussion centers on wine vinegar and evaluates the effects of these different processes on its chemical and sensory properties. PMID:24574887

Self-assessment procedure using fuzzy sets

NASA Astrophysics Data System (ADS)

Mimi, Fotini

2000-10-01

Self-Assessment processes, initiated by a company itself and carried out by its own people, are considered to be the starting point for a regular strategic or operative planning process to ensure a continuous quality improvement. Their importance has increased by the growing relevance and acceptance of international quality awards such as the Malcolm Baldrige National Quality Award, the European Quality Award and the Deming Prize. Especially award winners use the instrument of a systematic and regular Self-Assessment and not only because they have to verify their quality and business results for at least three years. The Total Quality Model of the European Foundation for Quality Management (EFQM), used for the European Quality Award, is the basis for Self-Assessment in Europe. This paper presents a self-assessment supporting method based on a methodology of fuzzy control systems providing an effective means of converting the linguistic approximation into an automatic control strategy. In particular, the elements of the Quality Model mentioned above are interpreted as linguistic variables. The LR-type of a fuzzy interval is used for their representation. The input data has a qualitative character based on empirical investigation and expert knowledge and therefore the base- variables are ordinal scaled. The aggregation process takes place on the basis of a hierarchical structure. Finally, in order to render the use of the method more practical a software system on PC basis is developed and implemented.

Quality evaluation of Hypericum ascyron extract by two-dimensional high-performance liquid chromatography coupled with the colorimetric 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide method.

PubMed

Li, Xiu-Mei; Luo, Xue-Gang; Zhang, Chao-Zheng; Wang, Nan; Zhang, Tong-Cun

2015-02-01

In this paper, a heart-cutting two-dimensional high-performance liquid chromatography coupled with the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) method was established for controlling the quality of different batches of Hypericum ascyron extract for the first time. In comparison with the common one-dimensional fingerprint, the second-dimensional fingerprint compiled additional spectral data and was hence more informative. The quality of H. ascyron extract was further evaluated by similarity measures and the same results were achieved, the correlation coefficients of the similarity of ten batches of H. ascyron extract were ＞0.99. Furthermore, we also evaluated the quality of the ten batches of H. ascyron extract by antibacterial activity. The result demonstrated that the quality of the ten batches of H. ascyron extract was not significantly different by MTT. Finally, we demonstrated that the second-dimensional fingerprint coupled with the MTT method was a more powerful tool to characterize the quality of samples of batch to batch. Therefore the proposed method could be used to comprehensively conduct the quality control of traditional Chinese medicines. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Estimation of 3D reconstruction errors in a stereo-vision system

NASA Astrophysics Data System (ADS)

Belhaoua, A.; Kohler, S.; Hirsch, E.

2009-06-01

The paper presents an approach for error estimation for the various steps of an automated 3D vision-based reconstruction procedure of manufactured workpieces. The process is based on a priori planning of the task and built around a cognitive intelligent sensory system using so-called Situation Graph Trees (SGT) as a planning tool. Such an automated quality control system requires the coordination of a set of complex processes performing sequentially data acquisition, its quantitative evaluation and the comparison with a reference model (e.g., CAD object model) in order to evaluate quantitatively the object. To ensure efficient quality control, the aim is to be able to state if reconstruction results fulfill tolerance rules or not. Thus, the goal is to evaluate independently the error for each step of the stereo-vision based 3D reconstruction (e.g., for calibration, contour segmentation, matching and reconstruction) and then to estimate the error for the whole system. In this contribution, we analyze particularly the segmentation error due to localization errors for extracted edge points supposed to belong to lines and curves composing the outline of the workpiece under evaluation. The fitting parameters describing these geometric features are used as quality measure to determine confidence intervals and finally to estimate the segmentation errors. These errors are then propagated through the whole reconstruction procedure, enabling to evaluate their effect on the final 3D reconstruction result, specifically on position uncertainties. Lastly, analysis of these error estimates enables to evaluate the quality of the 3D reconstruction, as illustrated by the shown experimental results.

Identification of quality markers of Yuanhu Zhitong tablets based on integrative pharmacology and data mining.

PubMed

Li, Ke; Li, Junfang; Su, Jin; Xiao, Xuefeng; Peng, Xiujuan; Liu, Feng; Li, Defeng; Zhang, Yi; Chong, Tao; Xu, Haiyu; Liu, Changxiao; Yang, Hongjun

2018-03-07

The quality evaluation of traditional Chinese medicine (TCM) formulations is needed to guarantee the safety and efficacy. In our laboratory, we established interaction rules between chemical quality control and biological activity evaluations to study Yuanhu Zhitong tablets (YZTs). Moreover, a quality marker (Q-marker) has recently been proposed as a new concept in the quality control of TCM. However, no appropriate methods are available for the identification of Q-markers from the complex TCM systems. We aimed to use an integrative pharmacological (IP) approach to further identify Q-markers from YZTs through the integration of multidisciplinary knowledge. In addition, data mining was used to determine the correlation between multiple constituents of this TCM and its bioactivity to improve quality control. The IP approach was used to identify the active constituents of YZTs and elucidate the molecular mechanisms by integrating chemical and biosynthetic analyses, drug metabolism, and network pharmacology. Data mining methods including grey relational analysis (GRA) and least squares support vector machine (LS-SVM) regression techniques, were used to establish the correlations among the constituents and efficacy, and dose efficacy in multiple dimensions. Seven constituents (tetrahydropalmatine, α-allocryptopine, protopine, corydaline, imperatorin, isoimperatorin, and byakangelicin) were identified as Q-markers of YZT using IP based on their high abundance, specific presence in the individual herbal constituents and the product, appropriate drug-like properties, and critical contribution to the bioactivity of the mixture of YZT constituents. Moreover, three Q-markers (protopine, α-allocryptopine, and corydaline) were highly correlated with the multiple bioactivities of the YZTs, as found using data mining. Finally, three constituents (tetrahydropalmatine, corydaline, and imperatorin) were chosen as minimum combinations that both distinguished the authentic components from false products and indicated the intensity of bioactivity to improve the quality control of YZTs. Tetrahydropalmatine, imperatorin, and corydaline could be used as minimum combinations to effectively control the quality of YZTs. Copyright © 2018. Published by Elsevier GmbH.

Development of a Model Following Control Law for Inflight Simulation and Flight Controls Research

NASA Technical Reports Server (NTRS)

Takahashi, Mark; Fletcher, Jay; Aiken, Edwin W. (Technical Monitor)

1994-01-01

The U.S. Army and NASA are currently developing the Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) at the Ames Research Center. RASCAL, shown in Figure 1, is a UH-60, which is being modified in a phased development program to have a research fly-by-wire flight control system, and an advanced navigation research platform. An important part of the flight controls and handling qualities research on RASCAL will be an FCS design for the aircraft to achieve high bandwidth control responses and disturbance rejection characteristics. Initially, body states will be used as feedbacks, but research into the use of rotor states will also be considered in later stages to maximize agility and maneuverability. In addition to supporting flight controls research, this FCS design will serve as the inflight simulation control law to support basic handling qualities, guidance, and displays research. Research in high bandwidth controls laws is motivated by the desire to improve the handling qualities in aggressive maneuvering and in severely degraded weather conditions. Naturally, these advantages will also improve the quality of the model following, thereby improving the inflight simulation capabilities of the research vehicle. High bandwidth in the control laws provides tighter tracking allowing for higher response bandwidths which can meet handling qualities requirements for aggressive maneuvering. System sensitivity is also reduced preventing variations in the response from the vehicle due to changing flight conditions. In addition, improved gust rejection will result from this reduced sensitivity. The gust rejection coupled with a highly stable system will make more precise maneuvering and pointing possible in severely degraded weather conditions. The difficulty in achieving higher bandwidths from the control laws in the feedback and in the responses arises from the complexity of the models that are needed to produce a satisfactory design. In this case, high quality models that include rotor dynamics in a physically meaningful context must be available. A non-physical accounting of the rotor, such as lumping the effect as a time delay, is not likely to produce the desired results. High order simulation models based on first principals are satisfactory for the initial design phase in order to work out the control law design concept and get an initial set of gains. These models, however, have known deficiencies, which must be resolved in the final control law design. The error in the pitch-roll cross coupling is one notable deficiency that even sophisticated rotorcraft models including complex wake aerodynamics have yet to capture successfully. This error must be accounted for to achieve the desired decoupling. The approach to design the proposed inflight simulation control law is based on using a combination of simulation and identified models. The linear and nonlinear higher order models were used to develop an explicit model following control structure. This structure was developed to accommodate the design of control laws compliant to many of the quantitative requirements in ADS-33C. Furthermore, it also allows for control law research using rotor-state feedback and other design methodologies such as Quantitative Feedback and H-Infinity. Final gain selection will be based on higher order identified models which include rotor degrees of freedom.

An image analysis of TLC patterns for quality control of saffron based on soil salinity effect: A strategy for data (pre)-processing.

PubMed

Sereshti, Hassan; Poursorkh, Zahra; Aliakbarzadeh, Ghazaleh; Zarre, Shahin; Ataolahi, Sahar

2018-01-15

Quality of saffron, a valuable food additive, could considerably affect the consumers' health. In this work, a novel preprocessing strategy for image analysis of saffron thin layer chromatographic (TLC) patterns was introduced. This includes performing a series of image pre-processing techniques on TLC images such as compression, inversion, elimination of general baseline (using asymmetric least squares (AsLS)), removing spots shift and concavity (by correlation optimization warping (COW)), and finally conversion to RGB chromatograms. Subsequently, an unsupervised multivariate data analysis including principal component analysis (PCA) and k-means clustering was utilized to investigate the soil salinity effect, as a cultivation parameter, on saffron TLC patterns. This method was used as a rapid and simple technique to obtain the chemical fingerprints of saffron TLC images. Finally, the separated TLC spots were chemically identified using high-performance liquid chromatography-diode array detection (HPLC-DAD). Accordingly, the saffron quality from different areas of Iran was evaluated and classified. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effective Process Design for the Production of HIC-Resistant Linepipe Steels

NASA Astrophysics Data System (ADS)

Nieto, J.; Elías, T.; López, G.; Campos, G.; López, F.; Garcia, R.; De, Amar K.

2013-09-01

Production of slabs for sour service applications requires stringent control in slab internal quality and secondary processing so as to guarantee resistance against hydrogen-induced cracking (HIC). ArcelorMittal Steelmaking facility at Lazaro Cardenas, Mexico had recently implemented key steelmaking and casting processing technologies for production of sound, centerline free slabs for catering to the growing API Linepipe and off-shore market for sour service applications. State-of-the-art steelmaking with use of residual-free Direct-reduced Iron and continuous casting facilities with dynamic soft reduction were introduced for the production of slabs with ultra clean centerline. Introduction of controlled cooling of slabs for atomic hydrogen control well below 2 ppm has enabled production of slabs suitable for excellent HIC-resistant plate processing. Substantial tonnages of slabs were produced for production of API X52-X65 grade plates and pipes for sour service. Stringent quality control at each stage of steelmaking, casting, and slab inspection ensured slabs with excellent internal quality suitable for HIC resistance to be guaranteed in final product (Plates & Pipes). Details of production steps which resulted in successful HIC-resistant slab production have been described in this article.

Effectiveness of acupuncture therapy as treatment for tinnitus: a randomized controlled trial.

PubMed

Doi, Marcelo Yugi; Tano, Simone Sayomi; Schultz, Adriane Rocha; Borges, Ricardo; Marchiori, Luciana Lozza de Moraes

2016-01-01

Tinnitus is a subjective sensation of hearing a sound in the absence of an external stimulus, which significantly worsens the quality of life in 15-25% of affected individuals. To assess the effectiveness of acupuncture therapy for tinnitus. Randomized clinical trial ( 2T9T7Q) with 50 participants with tinnitus, divided into two groups: 25 participants in the acupuncture group and 25 participants in the control group. The acupuncture group received acupuncture treatment and the control group received no treatment. After a period of 5 weeks, they were called to perform the final evaluation and the control group received acupuncture treatment for ethical reasons. A statistically significant result was found for the primary outcome, reducing the intensity of tinnitus, with p=0.0001 and the secondary endpoint, showing improvement in quality of life, with p=0.0001. Chinese scalp acupuncture associated with bilateral electroacupuncture demonstrated, in the short term, a statistically significant improvement by reducing the level of tinnitus intensity, as well as improving the quality of life of individuals with tinnitus. Copyright © 2016 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

Lysosome and endoplasmic reticulum quality control pathways in Niemann-Pick type C disease

PubMed Central

Schultz, Mark L.; Krus, Kelsey L.; Lieberman, Andrew P.

2017-01-01

Lysosomal storage diseases result from inherited deficiencies of lysosomal hydrolytic activities or lipid transport. Collectively, these disorders are a common cause of morbidity in the pediatric population and are often associated with severe neurodegeneration. Among this group of diseases is Niemann-Pick type C, an autosomal recessive disorder of lipid trafficking that causes cognitive impairment, ataxia and death, most often in childhood. Here, we review the current knowledge of disease pathogenesis, with particular focus on insights gleaned from genetics and the study of model systems. Critical advances in understanding mechanisms that regulate intracellular cholesterol trafficking have emerged from this work and are highlighted. We review effects of disease-causing mutations on quality control pathways involving the lysosome and endoplasmic reticulum, and discuss how they function to clear the most common mutant protein found in Niemann-Pick type C patients, NPC1-I1061T. Finally, we summarize insights into the mechanisms that degrade misfolded transmembrane proteins in the endoplasmic reticulum and how manipulating these quality control pathways may lead to the identification of novel targets for disease-modifying therapies. PMID:27026653

Microalgae Nutraceuticals.

PubMed

Nicoletti, Marcello

2016-08-22

Among the new entries in the food supplements sector, an important place must be assigned to nutraceuticals containing microalgae, nowadays accounting for a large and rapidly expanding market. The marketed products are mainly based on three production strains, i.e., Spirulina and Chlorella, followed at a distance by Klamath. It is a composite situation, since two of them are cyanobacteria and the second one is eukaryotic. The reality is that each presents similarities in shape and appearance concerning the marketed form and several utilizations, and peculiarities that need special attention and adequate studies. First, general information is reported about the current scientific knowledge on each microalga, in particular the nutritional value and properties in prevention and wellbeing. Second, original studies are presented concerning the quality control of marketed products. Quality control is a key argument in nutraceuticals validation. Microalgae are particular organisms that need specific approaches to confirm identity and validate properties. The proposed control of quality is based on microscopic analysis of the morphologic characteristics. The final parts of this paper are dedicated to the need for specificity in uses and claims and to considerations about the future of microalgae in food supplements.

Microalgae Nutraceuticals

PubMed Central

Nicoletti, Marcello

2016-01-01

Among the new entries in the food supplements sector, an important place must be assigned to nutraceuticals containing microalgae, nowadays accounting for a large and rapidly expanding market. The marketed products are mainly based on three production strains, i.e., Spirulina and Chlorella, followed at a distance by Klamath. It is a composite situation, since two of them are cyanobacteria and the second one is eukaryotic. The reality is that each presents similarities in shape and appearance concerning the marketed form and several utilizations, and peculiarities that need special attention and adequate studies. First, general information is reported about the current scientific knowledge on each microalga, in particular the nutritional value and properties in prevention and wellbeing. Second, original studies are presented concerning the quality control of marketed products. Quality control is a key argument in nutraceuticals validation. Microalgae are particular organisms that need specific approaches to confirm identity and validate properties. The proposed control of quality is based on microscopic analysis of the morphologic characteristics. The final parts of this paper are dedicated to the need for specificity in uses and claims and to considerations about the future of microalgae in food supplements. PMID:28231149

Integrity management of offshore structures and its implication on computation of structural action effects and resistance

NASA Astrophysics Data System (ADS)

Moan, T.

2017-12-01

An overview of integrity management of offshore structures, with emphasis on the oil and gas energy sector, is given. Based on relevant accident experiences and means to control the associated risks, accidents are categorized from a technical-physical as well as human and organizational point of view. Structural risk relates to extreme actions as well as structural degradation. Risk mitigation measures, including adequate design criteria, inspection, repair and maintenance as well as quality assurance and control of engineering processes, are briefly outlined. The current status of risk and reliability methodology to aid decisions in the integrity management is briefly reviewed. Finally, the need to balance the uncertainties in data, methods and computational efforts and the cautious use and quality assurance and control in applying high fidelity methods to avoid human errors, is emphasized, and with a plea to develop both high fidelity as well as efficient, simplified methods for design.

Data Assimilation Experiments using Quality Controlled AIRS Version 5 Temperature Soundings

NASA Technical Reports Server (NTRS)

SUsskind, Joel

2008-01-01

The AIRS Science Team Version 5 retrieval algorithm has been finalized and is now operational at the Goddard DAAC in the processing (and reprocessing) of all AIRS data. The AIRS Science Team Version 5 retrieval algorithm contains two significant improvements over Version 4: 1) Improved physics allows for use of AIRS observations in the entire 4.3 pm C02 absorption band in the retrieval of temperature profile T(p) during both day and night. Tropospheric sounding 15 pm C02 observations are now used primarily in the generation of cloud cleared radiances Ri. This approach allows for the generation of accurate values of Ri and T(p) under most cloud conditions. 2) Another very significant improvement in Version 5 is the ability to generate accurate case-by-case, level-by-level error estimates for the atmospheric temperature profile, as well as for channel-by- channel error estimates for Ri. These error estimates are used for quality control of the retrieved products. We have conducted forecast impact experiments assimilating AIRS temperature profiles with different levels of quality control using the NASA GEOS-5 data assimilation system. Assimilation of quality controlled T(p) resulted in significantly improved forecast skill compared to that obtained from analyses obtained when all data used operationally by NCEP, except for AIRS data, is assimilated. We also conducted an experiment assimilating AIRS radiances uncontaminated by clouds, as done Operationally by ECMWF and NCEP. Forecasts resulting from assimilated AIRS radiances were of poorer quality than those obtained assimilating AIRS temperatures.

Piloted Evaluation of Modernized Limited Authority Control Laws in the NASA-Ames Vertical Motion Simulator (VMS)

NASA Technical Reports Server (NTRS)

Sahasrabudhe, Vineet; Melkers, Edgar; Faynberg, Alexander; Blanken, Chris L.

2003-01-01

The UH-60 BLACK HAWK was designed in the 1970s, when the US Army primarily operated during the day in good visual conditions. Subsequently, the introduction of night-vision goggles increased the BLACK HAWK'S mission effectiveness, but the accident rate also increased. The increased accident rate is strongly tied to increased pilot workload as a result of a degradation in visual cues. Over twenty years of research in helicopter flight control and handling qualities has shown that these degraded handling qualities can be recovered by modifying the response type of the helicopter in low speed flight. Sikorsky Aircraft Corporation initiated a project under the National Rotorcraft Technology Center (NRTC) to develop modern flight control laws while utilizing the existing partial authority Stability Augmentation System (SAS) of the BLACK HAWK. This effort resulted in a set of Modernized Control Laws (MCLAWS) that incorporate rate command and attitude command response types. Sikorsky and the US Army Aeroflightdynamics Directorate (AFDD) conducted a piloted simulation on the NASA-Ames Vertical h4otion Simulator, to assess potential handling qualities and to reduce the risk of subsequent implementation and flight test of these modern control laws on AFDD's EH-60L helicopter. The simulation showed that Attitude Command Attitude Hold control laws in pitch and roll improve handling qualities in the low speed flight regime. These improvements are consistent across a range of mission task elements and for both good and degraded visual environments. The MCLAWS perform better than the baseline UH-60A control laws in the presence of wind and turbulence. Finally, while the improved handling qualities in the pitch and roll axis allow the pilot to pay more attention to the vertical axis and hence altitude performance also improves, it is clear from pilot comments and altitude excursions that the addition of an Altitude Hold function would further reduce workload and improve overall handling qualities of the aircraft.

Complexity and Pilot Workload Metrics for the Evaluation of Adaptive Flight Controls on a Full Scale Piloted Aircraft

NASA Technical Reports Server (NTRS)

Hanson, Curt; Schaefer, Jacob; Burken, John J.; Larson, David; Johnson, Marcus

2014-01-01

Flight research has shown the effectiveness of adaptive flight controls for improving aircraft safety and performance in the presence of uncertainties. The National Aeronautics and Space Administration's (NASA)'s Integrated Resilient Aircraft Control (IRAC) project designed and conducted a series of flight experiments to study the impact of variations in adaptive controller design complexity on performance and handling qualities. A novel complexity metric was devised to compare the degrees of simplicity achieved in three variations of a model reference adaptive controller (MRAC) for NASA's F-18 (McDonnell Douglas, now The Boeing Company, Chicago, Illinois) Full-Scale Advanced Systems Testbed (Gen-2A) aircraft. The complexity measures of these controllers are also compared to that of an earlier MRAC design for NASA's Intelligent Flight Control System (IFCS) project and flown on a highly modified F-15 aircraft (McDonnell Douglas, now The Boeing Company, Chicago, Illinois). Pilot comments during the IRAC research flights pointed to the importance of workload on handling qualities ratings for failure and damage scenarios. Modifications to existing pilot aggressiveness and duty cycle metrics are presented and applied to the IRAC controllers. Finally, while adaptive controllers may alleviate the effects of failures or damage on an aircraft's handling qualities, they also have the potential to introduce annoying changes to the flight dynamics or to the operation of aircraft systems. A nuisance rating scale is presented for the categorization of nuisance side-effects of adaptive controllers.

Dynamics and controls in maglev systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Y.; Chen, S.S.; Rote, D.M.

1992-09-01

The dynamic response of magnetically levitated (maglev) ground transportation systems has important consequences for safety and ride quality, guideway design, and system costs. Ride quality is determined by vehicle response and by environmental factors such as humidity and noise. The dynamic response of the vehicles is the key element in determining ride quality, and vehicle stability is an important safety-related element. To design a proper guideway that provides acceptable ride quality in the stable region, vehicle dynamics must be understood. Furthermore the trade-off between guideway smoothness and the levitation and control systems must be considered if maglev systems are tomore » be economically feasible. The link between the guideway and the other maglev components is vehicle dynamics. For a commercial maglev system, vehicle dynamics must be analyzed and tested in detail. In this study, the role of dynamics and controls in maglev vehicle/guideway interactions is discussed, and the literature on modeling the dynamic interactions of vehicle/guideway and suspension controls for ground vehicles is reviewed. Particular emphasis is placed on modeling vehicle/guideway interactions and response characteristics of maglev systems for a multicar, multiload vehicle traveling on a single- or doublespan flexible guideway, including coupling effects of vehicle/guideway, comparison of concentrated and distributed loads, and ride comfort. Different control-law designs are introduced into vehicle suspensions when a simple two-degree-of-freedom vehicle model is applied. Active and semiactive control designs for primary and secondary suspensions do improve the response of vehicle and provide acceptable ride comfort. Finally, future research associated with dynamics and controls of vehicle/guideway systems is identified.« less

Conjunctively optimizing flash flood control and water quality in urban water reservoirs by model predictive control and dynamic emulation

NASA Astrophysics Data System (ADS)

Galelli, Stefano; Goedbloed, Albert; Schmitter, Petra; Castelletti, Andrea

2014-05-01

Urban water reservoirs are a viable adaptation option to account for increasing drinking water demand of urbanized areas as they allow storage and re-use of water that is normally lost. In addition, the direct availability of freshwater reduces pumping costs and diversifies the portfolios of drinking water supply. Yet, these benefits have an associated twofold cost. Firstly, the presence of large, impervious areas increases the hydraulic efficiency of urban catchments, with short time of concentration, increased runoff rates, losses of infiltration and baseflow, and higher risk of flash floods. Secondly, the high concentration of nutrients and sediments characterizing urban discharges is likely to cause water quality problems. In this study we propose a new control scheme combining Model Predictive Control (MPC), hydro-meteorological forecasts and dynamic model emulation to design real-time operating policies that conjunctively optimize water quantity and quality targets. The main advantage of this scheme stands in its capability of exploiting real-time hydro-meteorological forecasts, which are crucial in such fast-varying systems. In addition, the reduced computational requests of the MPC scheme allows coupling it with dynamic emulators of water quality processes. The approach is demonstrated on Marina Reservoir, a multi-purpose reservoir located in the heart of Singapore and characterized by a large, highly urbanized catchment with a short (i.e. approximately one hour) time of concentration. Results show that the MPC scheme, coupled with a water quality emulator, provides a good compromise between different operating objectives, namely flood risk reduction, drinking water supply and salinity control. Finally, the scheme is used to assess the effect of source control measures (e.g. green roofs) aimed at restoring the natural hydrological regime of Marina Reservoir catchment.

The use of gelatine in long-term storage (up to 48 hr) at 5°C preserves the pre-freezing and post-thawing quality of brown bear sperm.

PubMed

Lopez-Urueña, E; Anel-López, L; Borragan, S; Ortega Ferrusola, C; Manrique, P; de Paz, P; Anel, L; Alvarez, M

2016-10-01

Sedimentation of spermatozoa occurs during long-term liquid storage and this may produce deleterious changes. Our aim was to apply gelatine supplementation during long-term pre-freezing storage of bear sperm, applying final dilution and 6% glycerol at room temperature and cool in straws. We tested four models of sperm storage using a 1:1 dilution in TTF-ULE-Bear extender (TesT-fructose-egg yolk-glycerol 6%): (i) second 1:1 dilution at room temperature (RT), cooling at 5°C in a tube and final dilution (100 × 10(6)  sperm ml(-1) ) (Standard); (ii) final dilution at RT and cooling in a tube (FD-Tube); (iii) final dilution at RT and cooling in 0.25 ml plastic straw (FD-Straw); and (iv) final dilution at RT in extender supplemented with 1.5% gelatine (Gelatine) and cooling in a 0.25 ml plastic straw. A Standard sample was stored at 5°C for 1 hr (Control); the rest of the samples (Standard, FD-Tube, FD-Straw, Gelatine) were stored for 24 or 48 hrs before freezing (100 × 10(6)  sperm ml(-1) , glycerol 6%). The quality of the samples was assessed for motility by CASA, and viability (SYBR-14/propidium iodide-PI-; VIAB), acrosomal status (PNA-FITC/PI; iACR) and apoptotic status (YO-PRO-1/PI; YOPRO-) by flow cytometry. At pre-freezing, after 48 hr, Gelatine showed significantly higher viability (for VIAB and YOPRO-) and progressiveness (PM, LIN and STR). At 48 hr, Gelatine showed similar YOPRO-, iACR, LIN, STR and ALH respect to Control. At both 24 and 48 h post-thawing, Gelatine sample had similar scores for YOPRO-, iACR, LIN, STR, WOB and VIAB (only 24 hr) when compared with Control, and lower for TM, PM, rapidPM, VAP and ALH. No differences were found among others experimental groups with respect to Control. In conclusion, gelatine could be a suitable alternative to preserve the viability and progressive motility of brown bear ejaculates during long-term pre-freezing storage at 5°C. © 2016 Blackwell Verlag GmbH.

A Novel Hybrid Error Criterion-Based Active Control Method for on-Line Milling Vibration Suppression with Piezoelectric Actuators and Sensors

PubMed Central

Zhang, Xingwu; Wang, Chenxi; Gao, Robert X.; Yan, Ruqiang; Chen, Xuefeng; Wang, Shibin

2016-01-01

Milling vibration is one of the most serious factors affecting machining quality and precision. In this paper a novel hybrid error criterion-based frequency-domain LMS active control method is constructed and used for vibration suppression of milling processes by piezoelectric actuators and sensors, in which only one Fast Fourier Transform (FFT) is used and no Inverse Fast Fourier Transform (IFFT) is involved. The correction formulas are derived by a steepest descent procedure and the control parameters are analyzed and optimized. Then, a novel hybrid error criterion is constructed to improve the adaptability, reliability and anti-interference ability of the constructed control algorithm. Finally, based on piezoelectric actuators and acceleration sensors, a simulation of a spindle and a milling process experiment are presented to verify the proposed method. Besides, a protection program is added in the control flow to enhance the reliability of the control method in applications. The simulation and experiment results indicate that the proposed method is an effective and reliable way for on-line vibration suppression, and the machining quality can be obviously improved. PMID:26751448

77 FR 64468 - Circular Welded Carbon-Quality Steel Pipe From India: Final Affirmative Countervailing Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-22

...-Quality Steel Pipe From India: Final Affirmative Countervailing Duty Determination AGENCY: Import... exporters of circular welded carbon-quality steel pipe (``circular welded pipe'') from India. For... determination.\\1\\ \\1\\ See Circular Welded Carbon-Quality Steel Pipe From India: Preliminary Affirmative...

77 FR 71751 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Control of Stationary...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-04

... Final Rules section of this Federal Register, EPA is approving the State's SIP submittal as a direct... . Follow the on-line instructions for submitting comments. B. Email: cox[email protected] . C. Mail: EPA-R03-OAR-2012-0619, Kathleen Cox Associate Director, Office of Permits and Air Toxics, Mailcode 3AP10...

Final Environmental Assessment: Demolition of Barracks (Building T-2) at Ipswich Antenna Test Facility

DTIC Science & Technology

2011-12-01

EIAP), managed the preparation and was the primary author of this environmental assessment. QAULITY ASSURANCE LEADER Cravedi, Gregory. 66 ABG/CE...BMP Best Management Practice CEQ Council on Environmental Quality CERCLA Comprehensive Environmental Response, Compensation, and Liability Act...Assessment EMCS Energy Management Control System ESC Electronic Systems Center FEMA Federal Emergency Management Agency FIRM Federal

Northeast Texas Agricultural Literacy Network: A-Lit-NeT: A Rural College Partnership Project. Final Report.

ERIC Educational Resources Information Center

Carnes, John

In northeast Texas, 47% of the adults over the age of 25 have not graduated from high school. Area agricultural businesses are rapidly implementing new technologies and quality control measures, both of which require literate and highly trainable workers. To meet these needs, a partnership project was undertaken between Northeast Texas Community…

Modeling in the quality by design environment: Regulatory requirements and recommendations for design space and control strategy appointment.

PubMed

Djuris, Jelena; Djuric, Zorica

2017-11-30

Mathematical models can be used as an integral part of the quality by design (QbD) concept throughout the product lifecycle for variety of purposes, including appointment of the design space and control strategy, continual improvement and risk assessment. Examples of different mathematical modeling techniques (mechanistic, empirical and hybrid) in the pharmaceutical development and process monitoring or control are provided in the presented review. In the QbD context, mathematical models are predominantly used to support design space and/or control strategies. Considering their impact to the final product quality, models can be divided into the following categories: high, medium and low impact models. Although there are regulatory guidelines on the topic of modeling applications, review of QbD-based submission containing modeling elements revealed concerns regarding the scale-dependency of design spaces and verification of models predictions at commercial scale of manufacturing, especially regarding real-time release (RTR) models. Authors provide critical overview on the good modeling practices and introduce concepts of multiple-unit, adaptive and dynamic design space, multivariate specifications and methods for process uncertainty analysis. RTR specification with mathematical model and different approaches to multivariate statistical process control supporting process analytical technologies are also presented. Copyright © 2017 Elsevier B.V. All rights reserved.

The impact of a disease management programme for type 2 diabetes on health-related quality of life: multilevel analysis of a cluster-randomised controlled trial.

PubMed

Panisch, Sigrid; Johansson, Tim; Flamm, Maria; Winkler, Henrike; Weitgasser, Raimund; Sönnichsen, Andreas C

2018-01-01

Type 2 diabetes is a chronic disease associated with poorer health outcomes and decreased health related quality of life (HRQoL). The aim of this analysis was to explore the impact of a disease management programme (DMP) in type 2 diabetes on HRQoL. A multilevel model was used to explain the variation in EQ-VAS. A cluster-randomized controlled trial-analysis of the secondary endpoint HRQoL. Our study population were general practitioners and patients in the province of Salzburg. The DMP "Therapie-Aktiv" was implemented in the intervention group, and controls received usual care. Outcome measure was a change in EQ-VAS after 12 months. For comparison of rates, we used Fisher's Exact test; for continuous variables the independent T test or Welch test were used. In the multilevel modeling, we examined various models, continuously adding variables to explain the variation in the dependent variable, starting with an empty model, including only the random intercept. We analysed random effects parameters in order to disentangle variation of the final EQ-VAS. The EQ-VAS significantly increased within the intervention group (mean difference 2.19, p = 0.005). There was no significant difference in EQ-VAS between groups (mean difference 1.00, p = 0.339). In the intervention group the improvement was more distinct in women (2.46, p = 0.036) compared to men (1.92, p = 0.063). In multilevel modeling, sex, age, family and work circumstances, any macrovascular diabetic complication, duration of diabetes, baseline body mass index and baseline EQ-VAS significantly influence final EQ-VAS, while DMP does not. The final model explains 28.9% (EQ-VAS) of the total variance. Most of the unexplained variance was found on patient-level (95%) and less on GP-level (5%). DMP "Therapie-Aktiv" has no significant impact on final EQ-VAS. The impact of DMPs in type 2 diabetes on HRQoL is still unclear and future programmes should focus on patient specific needs and predictors in order to improve HRQoL. Trial registration Current Controlled trials Ltd., ISRCTN27414162.

Inverse simulation system for evaluating handling qualities during rendezvous and docking

NASA Astrophysics Data System (ADS)

Zhou, Wanmeng; Wang, Hua; Thomson, Douglas; Tang, Guojin; Zhang, Fan

2017-08-01

The traditional method used for handling qualities assessment of manned space vehicles is too time-consuming to meet the requirements of an increasingly fast design process. In this study, a rendezvous and docking inverse simulation system to assess the handling qualities of spacecraft is proposed using a previously developed model-predictive-control architecture. By considering the fixed discrete force of the thrusters of the system, the inverse model is constructed using the least squares estimation method with a hyper-ellipsoidal restriction, the continuous control outputs of which are subsequently dispersed by pulse width modulation with sensitivity factors introduced. The inputs in every step are deemed constant parameters, and the method could be considered as a general method for solving nominal, redundant, and insufficient inverse problems. The rendezvous and docking inverse simulation is applied to a nine-degrees-of-freedom platform, and a novel handling qualities evaluation scheme is established according to the operation precision and astronauts' workload. Finally, different nominal trajectories are scored by the inverse simulation and an established evaluation scheme. The scores can offer theoretical guidance for astronaut training and more complex operation missions.

Growth of High-Quality GaAs on Ge by Controlling the Thickness and Growth Temperature of Buffer Layer

NASA Astrophysics Data System (ADS)

Zhou, Xu-Liang; Pan, Jiao-Qing; Yu, Hong-Yan; Li, Shi-Yan; Wang, Bao-Jun; Bian, Jing; Wang, Wei

2014-12-01

High-quality GaAs thin films grown on miscut Ge substrates are crucial for GaAs-based devices on silicon. We investigate the effect of different thicknesses and temperatures of GaAs buffer layers on the crystal quality and surface morphology of GaAs on Ge by metal-organic chemical vapor deposition. Through high resolution x-ray diffraction measurements, it is demonstrated that the full width at half maximum for the GaAs epilayer (Ge substrate) peak could achieve 19.3 (11.0) arcsec. The value of etch pit density could be 4×104 cm-2. At the same time, GaAs surfaces with no pyramid-shaped pits are obtained when the buffer layer growth temperature is lower than 360°C, due to effective inhibition of initial nucleation at terraces of the Ge surface. In addition, it is shown that large island formation at the initial stage of epitaxial growth is a significant factor for the final rough surface and that this initial stage should be carefully controlled when a device quality GaAs surface is desired.

Marital violence and coparenting quality after separation.

PubMed

Hardesty, Jennifer L; Crossman, Kimberly A; Khaw, Lyndal; Raffaelli, Marcela

2016-04-01

Research has identified multiple predictors of coparenting quality, but few studies have investigated how intimate partner violence (IPV) affects divorcing couples' coparenting relationships. We addressed this question in a sample of 154 mothers with different marital IPV experiences. Mothers were recruited within 4 months of a divorce filing and completed two interviews 3 months apart. At Time 1, mothers reported on violence and coercive control during marriage, and postseparation behavioral (e.g., parental communication), emotional (e.g., anger), and intrusion (e.g., harassment) dynamics; at Time 2, they reported on coparenting quality (i.e., levels of support and conflict). In the overall sample, divorce and violence variables independently predicted coparenting quality. Mothers were then classified into three groups: no violence (NV; n = 74), situational couple violence (SCV; n = 46), or coercive controlling violence (CCV; n = 34). Of the 3, coparenting quality was lowest in the CCV group. While the SCV group was similar to the NV group on most divorce-related variables, the CCV group reported more hostility at separation and placed less importance on father-child relationships. Finally, patterns of association between study variables and coparenting quality showed some parallels between the SCV and NV groups. For CCV, postseparation harassment and fear were negatively associated with coparenting quality. Findings contribute to understanding predictors of coparenting quality and support the need for individualized assessments of divorce cases with attention to IPV dynamics. (c) 2016 APA, all rights reserved).

Marital Violence and Coparenting Quality After Separation

PubMed Central

Hardesty, Jennifer L.; Crossman, Kimberly A.; Khaw, Lyndal; Raffaelli, Marcela

2016-01-01

Research has identified multiple predictors of coparenting quality, but few studies have investigated how intimate partner violence (IPV) affects divorcing couples’ coparenting relationships. We addressed this question in a sample of 154 mothers with different marital IPV experiences. Mothers were recruited within four months of a divorce filing and completed two interviews three months apart. At Time 1, mothers reported on violence and coercive control during marriage, and postseparation behavioral (e.g., parental communication), emotional (e.g., anger), and intrusion (e.g., harassment) dynamics; at Time 2, they reported on coparenting quality (i.e., levels of support and conflict). In the overall sample, divorce and violence variables independently predicted coparenting quality. Mothers were then classified into three groups: no violence (NV; n = 74), situational couple violence (SCV; n = 46), or coercive controlling violence (CCV; n = 34). Of the three, coparenting quality was lowest in the CCV group. While the SCV group was similar to the NV group on most divorce-related variables, the CCV group reported more hostility at separation and placed less importance on father-child relationships. Finally, patterns of association between study variables and coparenting quality showed some parallels between the SCV and NV groups. For CCV, postseparation harassment and fear were negatively associated with coparenting quality. Findings contribute to understanding predictors of coparenting quality and support the need for individualized assessments of divorce cases with attention to IPV dynamics. PMID:26866837

Measurement Matters: Assessing Personal Qualities Other Than Cognitive Ability for Educational Purposes

PubMed Central

Duckworth, Angela L.; Yeager, David Scott

2016-01-01

There has been perennial interest in personal qualities other than cognitive ability that determine success, including self-control, grit, growth mindset, and many others. Attempts to measure such qualities for the purposes of educational policy and practice, however, are more recent. In this article, we identify serious challenges to doing so. We first address confusion over terminology, including the descriptor “non-cognitive.” We conclude that debate over the optimal name for this broad category of personal qualities obscures substantial agreement about the specific attributes worth measuring. Next, we discuss advantages and limitations of different measures. In particular, we compare self-report questionnaires, teacher-report questionnaires, and performance tasks, using self-control as an illustrative case study to make the general point that each approach is imperfect in its own way. Finally, we discuss how each measure’s imperfections can affect its suitability for program evaluation, accountability, individual diagnosis, and practice improvement. For example, we do not believe any available measure is suitable for between-school accountability judgments. In addition to urging caution among policymakers and practitioners, we highlight medium-term innovations that may make measures of these personal qualities more suitable for educational purposes. PMID:27134288

76 FR 69927 - Approval of Air Quality Implementation Plans; California; South Coast; Attainment Plan for 1997...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-09

...EPA is approving in part and disapproving in part state implementation plan (SIP) revisions submitted by California to provide for attainment of the 1997 fine particulate matter (PM2.5) national ambient air quality standards in the Los Angeles-South Coast area (South Coast). These SIP revisions are the South Coast 2007 Air Quality Management Plan (South Coast 2007 AQMP) (revised 2011) and South Coast-related provisions of the 2007 State Strategy (revised 2009 and 2011). EPA is approving the emissions inventory; reasonably available control measures/reasonably available control technology demonstration; the reasonable further progress and attainment demonstrations and associated air quality modeling; and the transportation conformity motor vehicle emissions budgets. EPA is also granting California's request to extend the attainment deadline for the South Coast to April 5, 2015 and approving commitments to measures and reductions by the South Coast Air Quality Management District and the California Air Resources Board. Finally, we are disapproving the SIP's contingency measures and issuing a protective finding under 40 CFR 93.120(a)(3), and we are rejecting the assignment of 10 tons per day (tpd) of nitrogen oxide (NOX) reductions to the federal government.

Manufacture and Quality Control of Insert Coil with Real ITER TF Conductor

DOE PAGES

Ozeki, H.; Isono, T.; Uno, Y.; ...

2016-03-02

JAEA successfully completed the manufacture of the toroidal field (TF) insert coil (TFIC) for a performance test of the ITER TF conductor in the final design in cooperation with Hitachi, Ltd. The TFIC is a single-layer 8.875-turn solenoid coil with 1.44-m diameter. This will be tested for 68-kA current application in a 13-T external magnetic field. TFIC was manufactured in the following order: winding of the TF conductor, lead bending, fabrication of the electrical termination, heat treatment, turn insulation, installation of the coil into the support mandrel structure, vacuum pressure impregnation (VPI), structure assembly, and instrumentation. Here in this presentation,more » manufacture process and quality control status for the TFIC manufacturing are reported.« less

76 FR 22868 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

...-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Countervailing Duty Administrative... administrative review of the countervailing duty order on certain hot-rolled flat-rolled carbon- quality steel...-Quality Steel Products From Brazil: Preliminary Results of Countervailing Duty Administrative Review, 75...

[Testing of medicinal products produced from pooled plasma].

PubMed

Unkelbach, U; Hunfeld, A; Breitner-Ruddock, S

2014-10-01

Medicinal products produced from human plasma fall under the administrative batch release procedure of the competent authority. In Germany, this has been carried out since 1995 by the Paul Ehrlich Institute (PEI), the responsible state control agency for blood products. Medicinal products released for the European and national market are tested for quality, efficacy and safety. Experimental testing of the final product and the starting materials, the plasma pools, as well as control of the production documentation guarantee a constantly high product safety. In the 28,000 batches tested since the beginning of the state controlled batch release testing of these blood products at the PEI, there has been no transmission of infectious viruses (HIV, HBV and HCV) to any patient. The batch release has made a contribution to the improvement of product quality. This procedure is still an important tool to ensure safety of blood products. The PEI is integrated in the batch release network of the European Directorate for the Quality of Medicines & Health Care (EDQM) in Strasbourg. Regulations and guidelines for official control authority batch release (OCABR) ensure harmonized procedures for mutual recognition of batch release on the European level. The EU certificates and German national certificates are requested and accepted in over 70 countries worldwide. Experimental testing in the EU and the requisite certificates have developed into a seal of quality for the world market.

Quality control in the recycling stream of PVC from window frames by hyperspectral imaging

NASA Astrophysics Data System (ADS)

Luciani, Valentina; Serranti, Silvia; Bonifazi, Giuseppe; Di Maio, Francesco; Rem, Peter

2013-05-01

Polyvinyl chloride (PVC) is one of the most commonly used thermoplastic materials in respect to the worldwide polymer consumption. PVC is mainly used in the building and construction sector, products such as pipes, window frames, cable insulation, floors, coverings, roofing sheets, etc. are realised utilising this material. In recent years, the problem of PVC waste disposal gained increasing importance in the public discussion. The quantity of used PVC items entering the waste stream is gradually increased as progressively greater numbers of PVC products approach to the end of their useful economic lives. The quality of the recycled PVC depends on the characteristics of the recycling process and the quality of the input waste. Not all PVC-containing waste streams have the same economic value. A transparent relation between value and composition is required to decide if the recycling process is cost effective for a particular waste stream. An objective and reliable quality control technique is needed in the recycling industry for the monitoring of both recycled flow streams and final products in the plant. In this work hyperspectral imaging technique in the near infrared (NIR) range (1000-1700 nm) was applied to identify unwanted plastic contaminants and rubber present in PVC coming from windows frame waste in order to assess a quality control procedure during its recycling process. Results showed as PVC, PE and rubber can be identified adopting the NIR-HSI approach.

The effects of emotional intelligence training on the job performance of Australian aged care workers.

PubMed

Karimi, Leila; Leggat, Sandra G; Bartram, Timothy; Rada, Jiri

2018-05-09

Emotional intelligence (EI) training is popular among human resource practitioners, but there is limited evidence of the impact of such training on health care workers. In the current article, we examine the effects of EI training on quality of resident care and worker well-being and psychological empowerment in an Australian aged care facility. We use Bar-On's (1997) conceptualization of EI. We used a quasiexperimental design in 2014-2015 with experimental (training) and control (nontraining) groups of 60 participants in each group in two geographically separate facilities. Our final poststudy sample size was 27 participants for the training group and 17 participants for the control group. Over a 6-month period, we examined whether staff improved their well-being, psychological empowerment, and job performance measured as enhanced quality of care (self-rated and client-rated) by applying skills in EI. The results showed significant improvement among workers in the training group for EI scores, quality of care, general well-being, and psychological empowerment. There were no significant differences for the control group. Through examining the impact of EI training on staff and residents of an aged care facility, we demonstrate the benefits of EI training for higher quality of care delivery. This study demonstrates the practical process through which EI training can improve the work experiences of aged care workers, as well as the quality of care for residents.

Analytical and simulator study of advanced transport

NASA Technical Reports Server (NTRS)

Levison, W. H.; Rickard, W. W.

1982-01-01

An analytic methodology, based on the optimal-control pilot model, was demonstrated for assessing longitidunal-axis handling qualities of transport aircraft in final approach. Calibration of the methodology is largely in terms of closed-loop performance requirements, rather than specific vehicle response characteristics, and is based on a combination of published criteria, pilot preferences, physical limitations, and engineering judgment. Six longitudinal-axis approach configurations were studied covering a range of handling qualities problems, including the presence of flexible aircraft modes. The analytical procedure was used to obtain predictions of Cooper-Harper ratings, a solar quadratic performance index, and rms excursions of important system variables.

Lacking control over the trade-off between quality and quantity in visual short-term memory.

PubMed

Murray, Alexandra M; Nobre, Anna C; Astle, Duncan E; Stokes, Mark G

2012-01-01

Visual short-term memory (VSTM) is limited in the quantity and quality of items that can be retained over time. Importantly, these two mnemonic parameters interact: increasing the number of items in VSTM reduces the quality with which they are represented. Here, we ask whether this trade-off is under top-down control. Specifically, we test whether participants can strategically optimise the trade-off between quality and quantity for VSTM according to task demands. We manipulated strategic trade-off by varying expectations about the number of to-be-remembered items (Experiments 1-2) or the precision required for the memory-based judgement (Experiment 3). In a final experiment, we manipulated both variables in a complementary way to maximise the motivation to strategically control the balance between number and the quality of items encoded into VSTM. In different blocks, performance would benefit most either by encoding a large number of items with low precision or by encoding a small number of items with high precision (Experiment 4). In all experiments, we compared VSTM performance on trials matched for mnemonic demand, but within contexts emphasising the quality or quantity of VSTM representations. Across all four experiments, we found no evidence to suggest that participants use this contextual information to bias the balance between the number and precision of items in VSTM. Rather, our data suggest that the trade-off may be determined primarily by stimulus-driven factors at encoding.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kegel, T.M.

Calibration laboratories are faced with the need to become accredited or registered to one or more quality standards. One requirement common to all of these standards is the need to have in place a measurement assurance program. What is a measurement assurance program? Brian Belanger, in Measurement Assurance Programs: Part 1, describes it as a {open_quotes}quality assurance program for a measurement process that quantifies the total uncertainty of the measurements (both random and systematic components of error) with respect to national or designated standards and demonstrates that the total uncertainty is sufficiently small to meet the user`s requirements.{close_quotes} Rolf Schumachermore » is more specific in Measurement Assurance in Your Own Laboratory. He states, {open_quotes}Measurement assurance is the application of broad quality control principles to measurements of calibrations.{close_quotes} Here, the focus is on one important part of any measurement assurance program: implementation of statistical process control (SPC). Paraphrasing Juran`s Quality Control Handbook, a process is in statistical control if the only observed variations are those that can be attributed to random causes. Conversely, a process that exhibits variations due to assignable causes is not in a state of statistical control. Finally, Carrol Croarkin states, {open_quotes}In the measurement assurance context the measurement algorithm including instrumentation, reference standards and operator interactions is the process that is to be controlled, and its direct product is the measurement per se. The measurements are assumed to be valid if the measurement algorithm is operating in a state of control.{close_quotes} Implicit in this statement is the important fact that an out-of-control process cannot produce valid measurements. 7 figs.« less

An E-health solution for automatic sleep classification according to Rechtschaffen and Kales: validation study of the Somnolyzer 24 x 7 utilizing the Siesta database.

PubMed

Anderer, Peter; Gruber, Georg; Parapatics, Silvia; Woertz, Michael; Miazhynskaia, Tatiana; Klosch, Gerhard; Saletu, Bernd; Zeitlhofer, Josef; Barbanoj, Manuel J; Danker-Hopfe, Heidi; Himanen, Sari-Leena; Kemp, Bob; Penzel, Thomas; Grozinger, Michael; Kunz, Dieter; Rappelsberger, Peter; Schlogl, Alois; Dorffner, Georg

2005-01-01

To date, the only standard for the classification of sleep-EEG recordings that has found worldwide acceptance are the rules published in 1968 by Rechtschaffen and Kales. Even though several attempts have been made to automate the classification process, so far no method has been published that has proven its validity in a study including a sufficiently large number of controls and patients of all adult age ranges. The present paper describes the development and optimization of an automatic classification system that is based on one central EEG channel, two EOG channels and one chin EMG channel. It adheres to the decision rules for visual scoring as closely as possible and includes a structured quality control procedure by a human expert. The final system (Somnolyzer 24 x 7) consists of a raw data quality check, a feature extraction algorithm (density and intensity of sleep/wake-related patterns such as sleep spindles, delta waves, SEMs and REMs), a feature matrix plausibility check, a classifier designed as an expert system, a rule-based smoothing procedure for the start and the end of stages REM, and finally a statistical comparison to age- and sex-matched normal healthy controls (Siesta Spot Report). The expert system considers different prior probabilities of stage changes depending on the preceding sleep stage, the occurrence of a movement arousal and the position of the epoch within the NREM/REM sleep cycles. Moreover, results obtained with and without using the chin EMG signal are combined. The Siesta polysomnographic database (590 recordings in both normal healthy subjects aged 20-95 years and patients suffering from organic or nonorganic sleep disorders) was split into two halves, which were randomly assigned to a training and a validation set, respectively. The final validation revealed an overall epoch-by-epoch agreement of 80% (Cohen's kappa: 0.72) between the Somnolyzer 24 x 7 and the human expert scoring, as compared with an inter-rater reliability of 77% (Cohen's kappa: 0.68) between two human experts scoring the same dataset. Two Somnolyzer 24 x 7 analyses (including a structured quality control by two human experts) revealed an inter-rater reliability close to 1 (Cohen's kappa: 0.991), which confirmed that the variability induced by the quality control procedure, whereby approximately 1% of the epochs (in 9.5% of the recordings) are changed, can definitely be neglected. Thus, the validation study proved the high reliability and validity of the Somnolyzer 24 x 7 and demonstrated its applicability in clinical routine and sleep studies.

From in situ coal to the final coal product: A case study of the Danville Coal Member (Indiana)

USGS Publications Warehouse

Mastalerz, Maria; Padgett, P.L.

1999-01-01

A surface coal mine operation and preparation plant in southwestern Indiana was sampled to examine variations in coal quality and coal petrography parameters for the Danville Coal Member of the Dugger Formation (Pennsylvanian-Desmoinesian, Westphalian D). Representative samples from in situ coal, preparation plant feeds, and a final coal product were collected in order to compare coal quality, coal petrography, trace element concentrations, and ash chemistry of the coal to those of the product. Coal quality parameters of the in situ samples and various feeds, coarse refuse, and final product were variable. The quality of the final coal product was best predicted by the coal quality of the clean coal feed (from the middle portions of the seam). Some trace element contents, especially lead and arsenic, varied between the coal feeds and the product. Lead contents increased in the feeds and product compared to the channel sample of the raw coal, possibly due to contamination in the handling process.A surface coal mine operation and preparation plant in southwestern Indiana was sampled to examine variations in coal quality and coal petrography parameters for the Danville Coal Member of the Dugger Formation (Pennsylvanian-Desmoinesian, Westphalian D). Representative samples from in situ coal, preparation plant feeds, and a final coal product were collected in order to compare coal quality, coal petrography, trace element concentrations, and ash chemistry of the coal to those of the product. Coal quality parameters of the in situ samples and various feeds, coarse refuse, and final product were variable. The quality of the final coal product was best predicted by the coal quality of the clean coal feed (from the middle portions of the seam). Some trace element contents, especially lead and arsenic, varied between the coal feeds and the product. Lead contents increased in the feeds and product compared to the channel sample of the raw coal, possibly due to contamination in the handling process.

Mod-5A wind turbine generator program design report. Volume 3: Final design and system description, book 2

NASA Technical Reports Server (NTRS)

1984-01-01

The design, development and analysis of the 7.3MW MOD-5A wind turbine generator is documented. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 3, book 2 describes the performance and characteristics of the MOD-5A wind turbine generator in its final configuration. The subsystem for power generation, control, and instrumentation subsystems is described in detail. The manufacturing and construction plans, and the preparation of a potential site on Oahu, Hawaii, are documented. The quality assurance and safety plan, and analyses of failure modes and effects, and reliability, availability and maintainability are presented.

Air Quality Modeling Technical Support Document for the Final Cross State Air Pollution Rule Update

EPA Pesticide Factsheets

In this technical support document (TSD) we describe the air quality modeling performed to support the final Cross State Air Pollution Rule for the 2008 ozone National Ambient Air Quality Standards (NAAQS).

A novel approach to rapidly explore analytical markers for quality control of Radix Salviae Miltiorrhizae extract granules by robust principal component analysis with ultra-high performance liquid chromatography-ultraviolet-quadrupole time-of-flight mass spectrometry.

PubMed

Song, Jing-Zheng; Li, Song-Lin; Zhou, Yan; Qiao, Chun-Feng; Chen, Shi-Lin; Xu, Hong-Xi

2010-11-02

In a well-controlled experiment, outliers discriminated by robust principal component analysis (RPCA) represent contents in samples which are of particular quality distinguishable from the rest of the others, therefore chemical constituents in a natural product causing discrimination between outliers and the majority of samples could be considered as analytical markers for quality control. Based on this strategy, a novel approach for rapidly exploring characteristic analytical markers was proposed for the quality control of extract granules of Radix Salviae Miltiorrhizae (EGRSM). In this study, large sizes of samples were analyzed via high-throughput ultra-high performance liquid chromatography-ultraviolet-quadrupole time-of-flight mass spectrometry (UHPLC-UV-Q-Tof MS). RPCA was first performed on the three groups of samples: RSM (the raw material), the in-house prepared aqueous extract of Radix Salviae Miltiorrhizae (AERSM) and commercial product of EGRSM, to determine the variation of specific constituents between raw material and the final products as well as the effect of manufacturing process on the overall quality. Then RPCA was performed on the commercial products of EGRSM to explore the applicability of identified characteristic markers for the quality control of EGRSM. Candidate markers were extracted by RPCA, and their molecular formulae were determined by high resolution electrospray ionization-mass spectrometric (ESI-MS) analysis. The suitability of identified markers was then evaluated by determining the relationship between quantities of the identified markers with their antioxidant activities biologically, and further confirmed in a variety of samples. In conclusion, the combination of RPCA with UHPLC-UV-Q-Tof MS is a reliable means to identify chemical markers for evaluating quality of herbal medicines. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Incorporating Quality Control Information in the Sensor Web

NASA Astrophysics Data System (ADS)

Devaraju, Anusuriya; Kunkel, Ralf; Bogena, Heye

2013-04-01

The rapid development of sensing technologies had led to the creation of large amounts of heterogeneous environmental observations. The Sensor Web provides a wider access to sensors and observations via common protocols and specifications. Observations typically go through several levels of quality control, and aggregation before they are made available to end-users. Raw data are usually inspected, and related quality flags are assigned. Data are gap-filled, and errors are removed. New data series may also be derived from one or more corrected data sets. Until now, it is unclear how these kinds of information can be captured in the Sensor Web Enablement (SWE) framework. Apart from the quality measures (e.g., accuracy, precision, tolerance, or confidence), the levels of observational series, the changes applied, and the methods involved must be specified. It is important that this kind of quality control information is well described and communicated to end-users to allow for a better usage and interpretation of data products. In this paper, we describe how quality control information can be incorporated into the SWE framework. Concerning this, first, we introduce the TERENO (TERrestrial ENvironmental Observatories), an initiative funded by the large research infrastructure program of the Helmholtz Association in Germany. The main goal of the initiative is to facilitate the study of long-term effects of climate and land use changes. The TERENO Online Data RepOsitORry (TEODOOR) is a software infrastructure that supports acquisition, provision, and management of observations within TERENO via SWE specifications and several other OGC web services. Next, we specify changes made to the existing observational data model to incorporate quality control information. Here, we describe the underlying TERENO data policy in terms of provision and maintenance issues. We present data levels, and their implementation within TEODOOR. The data levels are adapted from those used by other similar systems such as CUAHSI, EarthScope and WMO. Finally, we outline recommendations for future work.

An index approach to performance-based payments for water quality.

PubMed

Maille, Peter; Collins, Alan R

2012-05-30

In this paper we describe elements of a field research project that presented farmers with economic incentives to control nitrate runoff. The approach used is novel in that payments are based on ambient water quality and water quantity produced by a watershed rather than proxies for water quality conservation. Also, payments are made based on water quality relative to a control watershed, and therefore, account for stochastic fluctuations in background nitrate levels. Finally, the program pays farmers as a group to elicit team behavior. We present our approach to modeling that allowed us to estimate prices for water and resulting payment levels. We then compare these preliminary estimates to the actual values recorded over 33 months of fieldwork. We find that our actual payments were 29% less than our preliminary estimates, due in part to the failure of our ecological model to estimate discharge accurately. Despite this shortfall, the program attracted the participation of 53% of the farmers in the watershed, and resulted in substantial nitrate abatement activity. Given this favorable response, we propose that research efforts focus on implementing field trials of group-level performance-based payments. Ideally these programs would be low risk and control for naturally occurring contamination. Copyright © 2012 Elsevier Ltd. All rights reserved.

Evaluation of Safety, Quality and Productivity in Construction

NASA Astrophysics Data System (ADS)

Usmen, M. A.; Vilnitis, M.

2015-11-01

This paper examines the success indicators of construction projects, safety, quality and productivity, in terms of their implications and impacts during and after construction. First safety is considered during construction with a focus on hazard identification and the prevention of occupational accidents and injuries on worksites. The legislation mandating safety programs, training and compliance with safety standards is presented and discussed. Consideration of safety at the design stage is emphasized. Building safety and the roles of building codes in prevention of structural failures are also covered in the paper together with factors affecting building failures and methods for their prevention. Quality is introduced in the paper from the perspective of modern total quality management. Concepts of quality management, quality control, quality assurance and Six Sigma and how they relate to building quality and structural integrity are discussed with examples. Finally, productivity concepts are presented with emphasis on effective project management to minimize loss of productivity, complimented by lean construction and lean Six Sigma principles. The paper concludes by synthesizing the relationships between safety, quality and productivity.

Effectiveness of equine therapy in children with psychomotor impairment.

PubMed

Del Rosario-Montejo, O; Molina-Rueda, F; Muñoz-Lasa, S; Alguacil-Diego, I M

2015-09-01

Equine therapy, an intervention method that has been practiced for decades around the world, is used to treat patients susceptible to psychomotor delays. We examine development of gross motor function compared to other psychomotor skills in patients undergoing this therapy, and analyse how this improvement affects general health status and quality of life. The study includes 11 children with delayed psychomotor development (aged 8.82 ± 3.89; 6 boys, 5 girls). The main study variables were gross motor function (GMFM-88) and perceived quality of life (Pediatric Quality of Life Inventory, PedsQL). Three measurements were performed: before and after a period of inactivity, and once again 2 months after the second measurement, following completion of a sustained period of therapy. We observed significant differences in overall results on the GMFM-88 between the initial and final tests and between the intermediate and final tests. Regarding the PedsQL quality of life scale, no statistically significant results were recorded. Noticeable changes in motor control were recorded throughout the course of the intervention, which suggests that equine therapy may be appropriate treatment in cases of delayed psychomotor development. Copyright © 2013 Sociedad Española de Neurología. Published by Elsevier España, S.L.U. All rights reserved.

F-16XL ship #1 (#849) during first flight of the Digital Flight Control System (DFCS)

NASA Technical Reports Server (NTRS)

1997-01-01

After completing its first flight with the Digital Flight Control System on December 16, 1997, the F-16XL #1 aircraft began a series of envelope expansion flights. On January 27 and 29, 1998, it successfully completed structural clearance tests, as well as most of the load testing Only flights at Mach 1.05 at 10,000 feet, Mach 1.1 at 15,000 feet, and Mach 1.2 at 20,000 feet remained. During the next flight, on February 4, an instrumentation problem cut short the planned envelope expansion tests. After the problem was corrected, the F-16XL returned to flight status, and on February 18 and 20, flight control and evaluation flights were made. Two more research flights were planned for the following week, but another problem appeared. During the ground start up, project personnel noticed that the leading edge flap moved without being commanded. The Digital Flight Control Computer was sent to the Lockheed-Martin facility at Fort Worth, where the problem was traced to a defective chip in the computer. After it was replaced, the F-16XL #1 flew a highly successful flight controls and handling qualities evaluation flight on March 26, clearing the way for the final tests. The final limited loads expansion flight occurred on March 31, and was fully successful. As a result, the on-site Lockheed-Martin loads engineer cleared the aircraft to Mach 1.8. The remaining two handling qualities and flight control evaluation flights were both made on April 3, 1998. These three flights concluded the flight test portion of the DFCS upgrade.

77 FR 36256 - Circular Welded Carbon-Quality Steel Pipe From India: Postponement of Final Determination of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-18

...-Quality Steel Pipe From India: Postponement of Final Determination of Antidumping Duty Investigation...- quality steel pipe from India.\\1\\ On June 1, 2012, the Department published its preliminary determination... is currently due on August 6, 2012. \\1\\ See Circular Welded Carbon-Quality Steel Pipe from India, the...

31P NMR spectroscopy in the quality control and authentication of extra-virgin olive oil: a review of recent progress.

PubMed

Dais, Photis; Spyros, Apostolos

2007-05-01

This review is a brief account on the application of a novel methodology to the quality control and authentication of extra-virgin olive oil. This methodology is based on the derivatization of the labile hydrogens of functional groups, such as hydroxyl and carboxyl groups, of olive oil constituents with the phosphorus reagent 2-chloro-4,4,5,5-tetramethyldioxaphospholane, and the use of the (31)P chemical shifts to identify the phosphitylated compounds. Various experimental aspects such as pertinent instrumentation, sample preparation, acquisition parameters and properties of the phosphorus reagent are reviewed. The strategy to assign the (31)P signals of the phosphitylated model compounds and olive oil constituents by employing 1D and 2D NMR experiments is presented. Finally, the capability of this technique to assess the quality and the genuineness of extra-virgin olive oil and to detect fraud is discussed. Copyright (c) 2007 John Wiley & Sons, Ltd.

WHO Expert Committee on Specifications for Pharmaceutical Preparations.

PubMed

2003-01-01

This report presents the recommendations of an international group of experts convened by the World Health Organization to consider matters concerning the quality assurance of pharmaceuticals and specifications for drug substances and dosage forms. Of particular relevance to drug regulatory authorities and pharmaceutical manufacturers, the report discusses activities related to the development of The International Pharmacopoeia and basic tests for pharmaceutical substances and dosage forms, as well as quality control of reference materials, good manufacturing practices (GMP), stability studies, inspection, hazard analysis, procurement, storage and other aspects of quality assurance of pharmaceuticals, and regulatory issues. The report is complemented by a number of annexes, including recommendations on the risk of transmitting animal spongiform encephalopathy agents via medicinal products, guidelines on GMP for pharmaceutical products, a model certificate for GMP and guidance on a GMP inspection report. The final annexes provide guidance on the application of Hazard Analysis and Critical Control Point (HACCP) method to pharmaceuticals, good storage practices and a procedure for assessing acceptability of pharmaceutical products for purchase by United Nations agencies.

Controlled fabrication of high-quality carbon nanoscrolls from monolayer graphene.

PubMed

Xie, Xu; Ju, Long; Feng, Xiaofeng; Sun, Yinghui; Zhou, Ruifeng; Liu, Kai; Fan, Shoushan; Li, Qunqing; Jiang, Kaili

2009-07-01

We report a simple and effective way of fabricating high-quality carbon nanoscrolls (CNSs), using isopropyl alcohol solution to roll up monolayer graphene predefined on SiO(2)/Si substrates. Transmission electron microscopy studies reveal that the CNS has a tube-like structure with a hollow core surrounded by graphene walls 0.35 nm apart. Raman spectroscopy studies show that the CNS is free of significant defects, and the electronic structure and phonon dispersion are slightly different from those of two-dimensional graphene. Finally, the CNS-based device is fabricated, directly on the SiO(2)/Si substrate. Electrical-transport measurements show that its resistance is weakly gate-dependent but strongly temperature-dependent. In addition, the CNS can sustain a high current density up to 5 x 10(7) A/cm(2), indicating that it is a good candidate for microcircuit interconnects. The controlled fabrication of high-quality CNSs may open up new opportunities for both fundamental and applied research of CNSs.

Orion Handling Qualities During ISS Rendezvous and Docking

NASA Technical Reports Server (NTRS)

Hart, Jeremy J.; Stephens, J. P.; Spehar, P.; Bilimoria, K.; Foster, C.; Gonzalex, R.; Sullivan, K.; Jackson, B.; Brazzel, J.; Hart, J.

2011-01-01

The Orion spacecraft was designed to rendezvous with multiple vehicles in low earth orbit (LEO) and beyond. To perform the required rendezvous and docking task, Orion must provide enough control authority to perform coarse translational maneuvers while maintaining precision to perform the delicate docking corrections. While Orion has autonomous docking capabilities, it is expected that final approach and docking operations with the International Space Station (ISS) will initially be performed in a manual mode. A series of evaluations was conducted by NASA and Lockheed Martin at the Johnson Space Center to determine the handling qualities (HQ) of the Orion spacecraft during different docking and rendezvous conditions using the Cooper-Harper scale. This paper will address the specifics of the handling qualities methodology, vehicle configuration, scenarios flown, data collection tools, and subject ratings and comments. The initial Orion HQ assessment examined Orion docking to the ISS. This scenario demonstrates the Translational Hand Controller (THC) handling qualities of Orion. During this initial assessment, two different scenarios were evaluated. The first was a nominal docking approach to a stable ISS, with Orion initializing with relative position dispersions and a closing rate of approximately 0.1 ft/sec. The second docking scenario was identical to the first, except the attitude motion of the ISS was modeled to simulate a stress case ( 1 degree deadband per axis and 0.01 deg/sec rate deadband per axis). For both scenarios, subjects started each run on final approach at a docking port-to-port range of 20 ft. Subjects used the THC in pulse mode with cues from the docking camera image, window views, and range and range rate data displayed on the Orion display units. As in the actual design, the attitude of the Orion vehicle was held by the automated flight control system at 0.5 degree deadband per axis. Several error sources were modeled including Reaction Control System (RCS) jet angular and position misalignment, RCS thrust magnitude uncertainty, RCS jet force direction uncertainty due to self plume impingement, and Orion center of mass uncertainty.

New Federal Air Quality Standards.

ERIC Educational Resources Information Center

Stopinski, O. W.

The report discusses the current procedures for establishing air quality standards, the bases for standards, and, finally, proposed and final National Primary and Secondary Ambient Air Quality Standards for sulfur dioxide, particulate matter, carbon monoxide, nonmethane hydrocarbons, photochemical oxidants, and nitrogen dioxide. (Author/RH)

Research on width control of Metal Fused-coating Additive Manufacturing based on active control

NASA Astrophysics Data System (ADS)

Ren, Chuan qi; Wei, Zheng ying; Wang, Xin; Du, Jun; Zhang, Shan; Zhang, Zhitong; Bai, Hao

2017-12-01

Given the stability of the shape of the forming layer is one of the key problems that affect the final quality of the sample morphology, taking a study on the forming process and the control method of morphology make a significant difference to metal fused-coating additive manufacturing (MFCAM) in achieving the efficient and stable forming. To improve the quality and precision of the samples of single-layer single pass, a control method of morphology based on active control was established by this paper. The real-time acquisition of image was realized by CCD and the characteristics of morphology of the forming process were simultaneously extracted. Making analysis of the characteristics of the width during the process, the relationship between the relative difference of different frames and moving speed was given. A large number of experiments are used to verify the response speed and accuracy of the system. The results show that the active system can improve the morphology of the sample and the smoothness of the width of the single channel, and increase the uniformity of width by 55.16%.

Effectiveness of Mindfulness-Based Stress Reduction Bibliotherapy: A Preliminary Randomized Controlled Trial.

PubMed

Hazlett-Stevens, Holly; Oren, Yelena

2017-06-01

This randomized controlled investigation examined the effectiveness of a self-help bibliotherapy format of the evidence-based mindfulness-based stress reduction (MBSR) intervention. College students seeking stress reduction were randomly assigned to a 10-week MBSR bibliotherapy intervention group (n = 47) or a no-treatment control group (n = 45). Self-report measures were collected at baseline and postintervention. A total of 25 bibliotherapy and 43 control group participants provided final data following the intervention period. Compared to the control group, bibliotherapy participants reported increased mindfulness following the intervention. Significant decreases on measures of depression, anxiety, stress, perceived stress, and anxiety sensitivity also were reported postintervention as well as increased quality of life in physical health, psychological, and environmental domains. No statistically significant group effects were found for social relationships quality of life domain, worry, and experiential avoidance measures. This MBSR workbook may provide an acceptable and effective alternative for motivated individuals seeking to reduce stress, at least for a select group of individuals who are willing and able to sustain participation in the intervention. © 2016 Wiley Periodicals, Inc.

The Effect of Reflexology on the Pain-Insomnia-Fatigue Disturbance Cluster of Breast Cancer Patients During Adjuvant Radiation Therapy.

PubMed

Tarrasch, Ricardo; Carmel-Neiderman, Narin N; Ben-Ami, Sarah; Kaufman, Bella; Pfeffer, Raphi; Ben-David, Merav; Gamus, Dorit

2018-01-01

To evaluate the effects of reflexology treatment on quality of life, sleep disturbances, and fatigue in breast cancer patients during radiation therapy. A total of 72 women with breast cancer (stages 1-3) scheduled for radiation therapy were recruited. Women were allocated upon their preference either to the group receiving reflexology treatments once a week concurrently with radiotherapy and continued for 10 weeks or to the control group (usual care). The Lee Fatigue Scale, General Sleep Disturbance Scale, and Multidimensional Quality of Life Scale Cancer were completed by each patient in both arms at the beginning of the radiation treatment, after 5 weeks, and after 10 weeks of reflexology treatment. The final analysis included 58 women. The reflexology treated group demonstrated statistically significant lower levels of fatigue after 5 weeks of radiation therapy (p < 0.001), compared to the control group. It was also detected that although the quality of life in the control group deteriorated after 5 and 10 weeks of radiation therapy (p < 0.01 and p < 0.05, respectively), it was preserved in the reflexology group, which also demonstrated a significant improvement in the quality of sleep after 10 weeks of radiation treatment (p < 0.05). Similar patterns were obtained in the assessment of the pain levels experienced by the patients. The results of the present study indicate that reflexology may have a positive effect on fatigue, quality of sleep, pain, and quality of life in breast cancer patients during radiation therapy. Reflexology prevented the decline in quality of life and significantly ameliorated the fatigue and quality of sleep of these patients. An encouraging trend was also noted in amelioration of pain levels.

Development of a Hot Working Steel Based on a Controlled Gas-Metal-Reaction

NASA Astrophysics Data System (ADS)

Ritzenhoff, Roman; Gharbi, Mohammad Malekipour

As a result of cost sensitiveness, the demand on hot working steels with advanced characteristics and properties are ascending. We have used a controlled gas-metal-reaction in a P-ESR furnace to produce high quality hot working steel. These types of materials are also known as High Nitrogen Steels (HNS). An overview of the development in a pressurized induction furnace to the final industrial scale using P-ESR will be provided. Different heat treatment strategies are conducted and their effect on mechanical properties is investigated.

Random Forest Application for NEXRAD Radar Data Quality Control

NASA Astrophysics Data System (ADS)

Keem, M.; Seo, B. C.; Krajewski, W. F.

2017-12-01

Identification and elimination of non-meteorological radar echoes (e.g., returns from ground, wind turbines, and biological targets) are the basic data quality control steps before radar data use in quantitative applications (e.g., precipitation estimation). Although WSR-88Ds' recent upgrade to dual-polarization has enhanced this quality control and echo classification, there are still challenges to detect some non-meteorological echoes that show precipitation-like characteristics (e.g., wind turbine or anomalous propagation clutter embedded in rain). With this in mind, a new quality control method using Random Forest is proposed in this study. This classification algorithm is known to produce reliable results with less uncertainty. The method introduces randomness into sampling and feature selections and integrates consequent multiple decision trees. The multidimensional structure of the trees can characterize the statistical interactions of involved multiple features in complex situations. The authors explore the performance of Random Forest method for NEXRAD radar data quality control. Training datasets are selected using several clear cases of precipitation and non-precipitation (but with some non-meteorological echoes). The model is structured using available candidate features (from the NEXRAD data) such as horizontal reflectivity, differential reflectivity, differential phase shift, copolar correlation coefficient, and their horizontal textures (e.g., local standard deviation). The influence of each feature on classification results are quantified by variable importance measures that are automatically estimated by the Random Forest algorithm. Therefore, the number and types of features in the final forest can be examined based on the classification accuracy. The authors demonstrate the capability of the proposed approach using several cases ranging from distinct to complex rain/no-rain events and compare the performance with the existing algorithms (e.g., MRMS). They also discuss operational feasibility based on the observed strength and weakness of the method.

ADVANCEMENTS IN NEUTRON RADIOGRAPHY WITHIN THE DEPARTMENT OF THE ARMY

DTIC Science & Technology

2016-11-01

Defense (DoD) production facility for direct use in quality control of munitions and weapons system by means of neutron radiographic inspection...UNCLASSIFIED UNCLASSIFIED AD-E403 813 Technical Report AREIS-TR-16004 ADVANCEMENTS IN NEUTRON RADIOGRAPHY WITHIN THE...REPORT DATE (DD-MM-YYYY) November 2016 2. REPORT TYPE Final 3. DATES COVERED (From – To) 4. TITLE AND SUBTITLE ADVANCEMENTS IN NEUTRON

Equilibrium moisture content during storage, manufacturing, and shipping of Bolivian wood products

Treesearch

Omar A. Espinoza; Brian H. Bond; Joseph R. Loferski

2007-01-01

After lumber is kiln-dried it is important to keep its moisture content (MC) as close as possible to its target value during all stages of production to assure final product quality. Knowledge of climate conditions at all stages of the manufacturing process is essential to provide a good control of lumber MC. This study is the first step to provide Bolivian companies...

Study on the quality of FRP fishing vessel based on improved Fishbone Chart

NASA Astrophysics Data System (ADS)

Sui, J. H.; Yu, Y. F.; Du, Q. F.; Jiang, D. W.

2018-01-01

The construction quality of FRP fishing vessels influences their production, use and industry development. In order to explore the factors that affect the construction quality of FRP fishing vessels, key factors affecting the construction quality of FRP fishing vessels are determined based on the quality problems of FRP fishing vessels constructed. The improved Fishbone Chart is used to analyze the eight factors of “human, machine, material, process, environment, inspection, design and information”. Taking the factors that affect the construction quality of FRP fishing vessels as the central target, the eight influencing factors were condensed into five aspects and a composite Fishbone Chart is drawn. The Fishbone Chart is used as the basic model, the influencing factors are sorted, screened and discriminated, and the system model convenient for construction site management and control is established. Finally, the causes of poor construction of FRP fishing vessels are analyzed and discussed, and relevant suggestions are put forward.

Urbanization, regime type and durability, and environmental degradation in Ghana.

PubMed

Adams, Samuel; Adom, Philip Kofi; Klobodu, Edem Kwame Mensah

2016-12-01

This study examines the effect of urbanization, income, trade openness, and institutional quality (i.e., regime type and durability) on environmental degradation in Ghana over the period 1965-2011. Using the bounds test approach to cointegration and the Fully Modified Phillip-Hansen (FMPH) technique, the findings show that urbanization, income, trade openness, and institutional quality have long-run cointegration with environmental degradation. Further, the results show that income, trade openness, and institutional quality are negatively associated with environmental degradation. This suggests that income, trade openness, and institutional quality enhance environmental performance. Urbanization, however, is positively related to environmental degradation. Additionally, long-run estimates conditioned on institutional quality reveal that the extent to which trade openness and urbanization enhance environmental performance is largely due to the presence of quality institutions (or democratic institutions). Finally, controlling for structural breaks, we find that trade openness, urbanization, and regime type (i.e., democracy) improve environmental performance significantly after the 1970s except for income.

78 FR 40497 - Notice of Availability of the Final Environmental Impact Statement/Environmental Impact Report...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-05

...In accordance with the National Environmental Policy Act of 1969, as amended (NEPA); the Federal Land Policy and Management Act of 1976, as amended; and the California Environmental Quality Act of 1970 (CEQA), the Bureau of Land Management (BLM), the United States Forest Service (USFS), and the Great Basin Unified Air Pollution Control District (GBUAPCD), a California State agency, have prepared a Final Environmental Impact Statement (EIS)/Environmental Impact Report (EIR) for the proposed Casa Diablo IV Geothermal Development Project near the town of Mammoth Lakes in Mono County, California, and by this notice are announcing its availability.

Does glycemic variability impact mood and quality of life?

PubMed

Penckofer, Sue; Quinn, Lauretta; Byrn, Mary; Ferrans, Carol; Miller, Michael; Strange, Poul

2012-04-01

Diabetes is a chronic condition that significantly impacts quality of life. Poor glycemic control is associated with more diabetes complications, depression, and worse quality of life. The impact of glycemic variability on mood and quality of life has not been studied. A descriptive exploratory design was used. Twenty-three women with type 2 diabetes wore a continuous glucose monitoring system for 72 h and completed a series of questionnaires. Measurements included (1) glycemic control shown by glycated hemoglobin and 24-h mean glucose, (2) glycemic variability shown by 24-h SD of the glucose readings, continuous overall net glycemic action (CONGA), and Fourier statistical models to generate smoothed curves to assess rate of change defined as "energy," and (3) mood (depression, anxiety, anger) and quality of life by questionnaires. Women with diabetes and co-morbid depression had higher anxiety, more anger, and lower quality of life than those without depression. Certain glycemic variability measures were associated with mood and quality of life. The 24-h SD of the glucose readings and the CONGA measures were significantly associated with health-related quality of life after adjusting for age and weight. Fourier models indicated that certain energy components were significantly associated with depression, trait anxiety, and overall quality of life. Finally, subjects with higher trait anxiety tended to have steeper glucose excursions. Data suggest that greater glycemic variability may be associated with lower quality of life and negative moods. Implications include replication of the study in a larger sample for the assessment of blood glucose fluctuations as they impact mood and quality of life.

Improving Forecast Skill by Assimilation of Quality Controlled AIRS Version 5 Temperature Soundings

NASA Technical Reports Server (NTRS)

Susskind, Joel; Reale, Oreste

2009-01-01

The AIRS Science Team Version 5 retrieval algorithm has been finalized and is now operational at the Goddard DAAC in the processing (and reprocessing) of all AIRS data. The AIRS Science Team Version 5 retrieval algorithm contains two significant improvements over Version 4: 1) Improved physics allows for use of AIRS observations in the entire 4.3 micron CO2 absorption band in the retrieval of temperature profile T(p) during both day and night. Tropospheric sounding 15 micron CO2 observations are now used primarily in the generation of cloud cleared radiances R(sub i). This approach allows for the generation of accurate values of R(sub i) and T(p) under most cloud conditions. 2) Another very significant improvement in Version 5 is the ability to generate accurate case-by-case, level-by-level error estimates for the atmospheric temperature profile, as well as for channel-by-channel error estimates for R(sub i). These error estimates are used for Quality Control of the retrieved products. We have conducted forecast impact experiments assimilating AIRS temperature profiles with different levels of Quality Control using the NASA GEOS-5 data assimilation system. Assimilation of Quality Controlled T(p) resulted in significantly improved forecast skill compared to that obtained from analyses obtained when all data used operationally by NCEP, except for AIRS data, is assimilated. We also conducted an experiment assimilating AIRS radiances uncontaminated by clouds, as done operationally by ECMWF and NCEP. Forecast resulting from assimilated AIRS radiances were of poorer quality than those obtained assimilating AIRS temperatures.

77 FR 25363 - Approval and Promulgation of Implementation Plans and Designations of Areas for Air Quality...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-30

... Ambient Air Quality Standard (NAAQS) AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule... of the 1997 8-hour ozone NAAQS as of the applicable date. DATES: Effective Date: This final rule will... action is EPA taking in this final rule? II. What is the background for this final action? III. What was...

Biowaste home composting: experimental process monitoring and quality control.

PubMed

Tatàno, Fabio; Pagliaro, Giacomo; Di Giovanni, Paolo; Floriani, Enrico; Mangani, Filippo

2015-04-01

Because home composting is a prevention option in managing biowaste at local levels, the objective of the present study was to contribute to the knowledge of the process evolution and compost quality that can be expected and obtained, respectively, in this decentralized option. In this study, organized as the research portion of a provincial project on home composting in the territory of Pesaro-Urbino (Central Italy), four experimental composters were first initiated and temporally monitored. Second, two small sub-sets of selected provincial composters (directly operated by households involved in the project) underwent quality control on their compost products at two different temporal steps. The monitored experimental composters showed overall decreasing profiles versus composting time for moisture, organic carbon, and C/N, as well as overall increasing profiles for electrical conductivity and total nitrogen, which represented qualitative indications of progress in the process. Comparative evaluations of the monitored experimental composters also suggested some interactions in home composting, i.e., high C/N ratios limiting organic matter decomposition rates and final humification levels; high moisture contents restricting the internal temperature regime; nearly horizontal phosphorus and potassium evolutions contributing to limit the rates of increase in electrical conductivity; and prolonged biowaste additions contributing to limit the rate of decrease in moisture. The measures of parametric data variability in the two sub-sets of controlled provincial composters showed decreased variability in moisture, organic carbon, and C/N from the seventh to fifteenth month of home composting, as well as increased variability in electrical conductivity, total nitrogen, and humification rate, which could be considered compatible with the respective nature of decreasing and increasing parameters during composting. The modeled parametric kinetics in the monitored experimental composters, along with the evaluation of the parametric central tendencies in the sub-sets of controlled provincial composters, all indicate that 12-15 months is a suitable duration for the appropriate development of home composting in final and simultaneous compliance with typical reference limits. Copyright © 2014 Elsevier Ltd. All rights reserved.

The Effect of Using Mobile Technology-Based Methods That Record Food or Nutrient Intake on Diabetes Control and Nutrition Outcomes: A Systematic Review.

PubMed

Porter, Judi; Huggins, Catherine E; Truby, Helen; Collins, Jorja

2016-12-17

(1) Background: Mobile technologies may be utilised for dietary intake assessment for people with diabetes. The published literature was systematically reviewed to determine the effect of using mobile electronic devices to record food or nutrient intake on diabetes control and nutrition outcomes; (2) Methods: The review protocol was registered with PROSPERO: registration number CRD42016050079, and followed PRISMA guidelines. Original research of mobile electronic devices where food or nutrient intake was recorded in people with diabetes with any treatment regimen, and where this intervention was compared with usual care or alternative treatment models, was considered. Quality was assessed using the Quality Criteria Checklist for Primary Research; (3) Results: Nine papers formed the final library with a range of interventions and control practices investigated. The food/nutrient intake recording component of the intervention and patient engagement with the technology was not well described. When assessed for quality, three studies rated positive, five were neutral and one negative. There was significantly greater improvement in HbA1c in the intervention group compared to the control group in four of the nine studies; (4) Conclusion: Based on the available evidence there are no clear recommendations for using technology to record dietary data in this population.

Comparison of five Lonicera flowers by simultaneous determination of multi-components with single reference standard method and principal component analysis.

PubMed

Gao, Wen; Wang, Rui; Li, Dan; Liu, Ke; Chen, Jun; Li, Hui-Jun; Xu, Xiaojun; Li, Ping; Yang, Hua

2016-01-05

The flowers of Lonicera japonica Thunb. were extensively used to treat many diseases. As the demands for L. japonica increased, some related Lonicera plants were often confused or misused. Caffeoylquinic acids were always regarded as chemical markers in the quality control of L. japonica, but they could be found in all Lonicera species. Thus, a simple and reliable method for the evaluation of different Lonicera flowers is necessary to be established. In this work a method based on single standard to determine multi-components (SSDMC) combined with principal component analysis (PCA) for control and distinguish of Lonicera species flowers have been developed. Six components including three caffeoylquinic acids and three iridoid glycosides were assayed simultaneously using chlorogenic acid as the reference standard. The credibility and feasibility of the SSDMC method were carefully validated and the results demonstrated that there were no remarkable differences compared with external standard method. Finally, a total of fifty-one batches covering five Lonicera species were analyzed and PCA was successfully applied to distinguish the Lonicera species. This strategy simplifies the processes in the quality control of multiple-componential herbal medicine which effectively adapted for improving the quality control of those herbs belonging to closely related species. Copyright © 2015 Elsevier B.V. All rights reserved.

The Effect of Using Mobile Technology-Based Methods That Record Food or Nutrient Intake on Diabetes Control and Nutrition Outcomes: A Systematic Review

PubMed Central

Porter, Judi; Huggins, Catherine E.; Truby, Helen; Collins, Jorja

2016-01-01

(1) Background: Mobile technologies may be utilised for dietary intake assessment for people with diabetes. The published literature was systematically reviewed to determine the effect of using mobile electronic devices to record food or nutrient intake on diabetes control and nutrition outcomes; (2) Methods: The review protocol was registered with PROSPERO: registration number CRD42016050079, and followed PRISMA guidelines. Original research of mobile electronic devices where food or nutrient intake was recorded in people with diabetes with any treatment regimen, and where this intervention was compared with usual care or alternative treatment models, was considered. Quality was assessed using the Quality Criteria Checklist for Primary Research; (3) Results: Nine papers formed the final library with a range of interventions and control practices investigated. The food/nutrient intake recording component of the intervention and patient engagement with the technology was not well described. When assessed for quality, three studies rated positive, five were neutral and one negative. There was significantly greater improvement in HbA1c in the intervention group compared to the control group in four of the nine studies; (4) Conclusion: Based on the available evidence there are no clear recommendations for using technology to record dietary data in this population. PMID:27999302

[Time-Temperature indicators (TTI). A means of quality control of produce].

PubMed

Durand, M P

1996-11-01

The author, after having dwelt on the mediatic importance of bacterial food poisonings, analyses their reasons, insisting on the importance of the temperature as a factor of bacterial growth. Among the cures for the association temperature-bacterial growth, the author draws attention to the benefits of the use of the time temperature indicators (TTI). He describes the purposes, the required qualities, the principles of activity. The "Lifelines TTI" proves to be interesting. The author describes the principles of activity, the directions for reading the results, the practical application. Finally he describes the remarks following on its use in large scale in a group of chain-stores. In the conclusion, the author points that these TTI are an attractive technical innovation regarding to the fresh foods, for the control of coldness in the human nutrition.

[Methodological quality and reporting quality evaluation of randomized controlled trials published in China Journal of Chinese Materia Medica].

PubMed

Yu, Dan-Dan; Xie, Yan-Ming; Liao, Xing; Zhi, Ying-Jie; Jiang, Jun-Jie; Chen, Wei

2018-02-01

To evaluate the methodological quality and reporting quality of randomized controlled trials(RCTs) published in China Journal of Chinese Materia Medica, we searched CNKI and China Journal of Chinese Materia webpage to collect RCTs since the establishment of the magazine. The Cochrane risk of bias assessment tool was used to evaluate the methodological quality of RCTs. The CONSORT 2010 list was adopted as reporting quality evaluating tool. Finally, 184 RCTs were included and evaluated methodologically, of which 97 RCTs were evaluated with reporting quality. For the methodological evaluating, 62 trials(33.70%) reported the random sequence generation; 9(4.89%) trials reported the allocation concealment; 25(13.59%) trials adopted the method of blinding; 30(16.30%) trials reported the number of patients withdrawing, dropping out and those lost to follow-up;2 trials （1.09%） reported trial registration and none of the trial reported the trial protocol; only 8(4.35%) trials reported the sample size estimation in details. For reporting quality appraising, 3 reporting items of 25 items were evaluated with high-quality,including: abstract, participants qualified criteria, and statistical methods; 4 reporting items with medium-quality, including purpose, intervention, random sequence method, and data collection of sites and locations; 9 items with low-quality reporting items including title, backgrounds, random sequence types, allocation concealment, blindness, recruitment of subjects, baseline data, harms, and funding;the rest of items were of extremely low quality(the compliance rate of reporting item<10%). On the whole, the methodological and reporting quality of RCTs published in the magazine are generally low. Further improvement in both methodological and reporting quality for RCTs of traditional Chinese medicine are warranted. It is recommended that the international standards and procedures for RCT design should be strictly followed to conduct high-quality trials. At the same time, in order to improve the reporting quality of randomized controlled trials, CONSORT standards should be adopted in the preparation of research reports and submissions. Copyright© by the Chinese Pharmaceutical Association.

Automated stent defect detection and classification with a high numerical aperture optical system

NASA Astrophysics Data System (ADS)

Bermudez, Carlos; Laguarta, Ferran; Cadevall, Cristina; Matilla, Aitor; Ibañez, Sergi; Artigas, Roger

2017-06-01

Stent quality control is a highly critical process. Cardiovascular stents have to be inspected 100% so as no defective stent is implanted in a human body. However, this visual control is currently performed manually and every stent could need tenths of minutes to be inspected. In this paper, a novel optical inspection system is presented. By the combination of a high numerical aperture (NA) optical system, a rotational stage and a line-scan camera, unrolled sections of the outer and inner surfaces of the stent are obtained and image-processed at high speed. Defects appearing in those surfaces and also in the edges are extremely contrasted due to the shadowing effect of the high NA illumination and acquisition approach. Therefore by means of morphological operations and a sensitivity parameter, defects are detected. Based on a trained defect library, a binary classifier sorts each kind of defect through a set of scoring vectors, providing the quality operator with all the required information to finally take a decision. We expect this new approach to make defect detection completely objective and to dramatically reduce the time and cost of stent quality control stage.

Operational Processing of Ground Validation Data for the Tropical Rainfall Measuring Mission

NASA Technical Reports Server (NTRS)

Kulie, Mark S.; Robinson, Mike; Marks, David A.; Ferrier, Brad S.; Rosenfeld, Danny; Wolff, David B.

1999-01-01

The Tropical Rainfall Measuring Mission (TRMM) satellite was successfully launched in November 1997. A primary goal of TRMM is to sample tropical rainfall using the first active spaceborne precipitation radar. To validate TRMM satellite observations, a comprehensive Ground Validation (GV) Program has been implemented for this mission. A key component of GV is the analysis and quality control of meteorological ground-based radar data from four primary sites: Melbourne, FL; Houston, TX; Darwin, Australia; and Kwajalein Atoll, RMI. As part of the TRMM GV effort, the Joint Center for Earth Systems Technology (JCET) at the University of Maryland, Baltimore County, has been tasked with developing and implementing an operational system to quality control (QC), archive, and provide data for subsequent rainfall product generation from the four primary GV sites. This paper provides an overview of the JCET operational environment. A description of the QC algorithm and performance, in addition to the data flow procedure between JCET and the TRNM science and Data Information System (TSDIS), are presented. The impact of quality-controlled data on higher level rainfall and reflectivity products will also be addressed, Finally, a brief description of JCET's expanded role into producing reference rainfall products will be discussed.

Statistical Quality Control of Moisture Data in GEOS DAS

NASA Technical Reports Server (NTRS)

Dee, D. P.; Rukhovets, L.; Todling, R.

1999-01-01

A new statistical quality control algorithm was recently implemented in the Goddard Earth Observing System Data Assimilation System (GEOS DAS). The final step in the algorithm consists of an adaptive buddy check that either accepts or rejects outlier observations based on a local statistical analysis of nearby data. A basic assumption in any such test is that the observed field is spatially coherent, in the sense that nearby data can be expected to confirm each other. However, the buddy check resulted in excessive rejection of moisture data, especially during the Northern Hemisphere summer. The analysis moisture variable in GEOS DAS is water vapor mixing ratio. Observational evidence shows that the distribution of mixing ratio errors is far from normal. Furthermore, spatial correlations among mixing ratio errors are highly anisotropic and difficult to identify. Both factors contribute to the poor performance of the statistical quality control algorithm. To alleviate the problem, we applied the buddy check to relative humidity data instead. This variable explicitly depends on temperature and therefore exhibits a much greater spatial coherence. As a result, reject rates of moisture data are much more reasonable and homogeneous in time and space.

California Air Quality State Implementation Plans; Final Approval; Butte County Air Quality Management District; Stationary Source Permits

EPA Pesticide Factsheets

EPA is taking final action to approve a revision to the Butte County Air Quality Management District (BCAQMD) portion of the California State Implementation Plan (SIP). This revision concerns the District's New Source Review (NSR) permitting program.

Medicare Program; FY 2018 Hospice Wage Index and Payment Rate Update and Hospice Quality Reporting Requirements. Final rule.

PubMed

2017-08-04

This final rule will update the hospice wage index, payment rates, and cap amount for fiscal year (FY) 2018. Additionally, this rule includes new quality measures and provides an update on the hospice quality reporting program.

77 FR 65712 - Circular Welded Carbon-Quality Steel Pipe From Vietnam; Termination of Investigation

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-30

... INTERNATIONAL TRADE COMMISSION [Investigation No. 701-TA-485 (Final)] Circular Welded Carbon-Quality Steel Pipe From Vietnam; Termination of Investigation AGENCY: United States International Trade... carbon-quality steel pipe from Vietnam (investigation No. 701-TA-485 (Final)) is terminated. DATES...

An update on methods for cryopreservation and thawing of hemopoietic stem cells.

PubMed

Lecchi, Lucilla; Giovanelli, Silvia; Gagliardi, Barbara; Pezzali, Ilaria; Ratti, Ilaria; Marconi, Maurizio

2016-06-01

The aim of this article is to review a number of variables that may affect the cryopreservation of minimally manipulated products containing allogeneic or autologous hemopoietic progenitor cells (HPC) used for transplantation, with particular reference to processing, type and addition of cryoprotectant, cell concentration, volume, freezing procedure, cooling rate, storage, thawing, and quality management. After defining final product's requirements in compliance with norms, laws and regulations, it is crucial to define the critical control points of the process. New approaches of processing were developed in the last few years such as automatic devices for volume reduction and high cell concentration in the frozen product. DMSO at 10% final concentration is still the most used cryoprotectant for HPC cryopreservation. Although controlled rate freezing is the recommended method for HPC cryopreservation, alternative methods may be used. Last generation vapor storage vessels ensure temperature stability better than older tanks. Their use may reduce risks of cross-contamination. Finally we review advantages and disadvantages of thawing procedures that may be carried out in the laboratory or at the patient's bedside. Copyright © 2016 Elsevier Ltd. All rights reserved.

Highly Efficient Training, Refinement, and Validation of a Knowledge-based Planning Quality-Control System for Radiation Therapy Clinical Trials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Nan; Carmona, Ruben; Sirak, Igor

Purpose: To demonstrate an efficient method for training and validation of a knowledge-based planning (KBP) system as a radiation therapy clinical trial plan quality-control system. Methods and Materials: We analyzed 86 patients with stage IB through IVA cervical cancer treated with intensity modulated radiation therapy at 2 institutions according to the standards of the INTERTECC (International Evaluation of Radiotherapy Technology Effectiveness in Cervical Cancer, National Clinical Trials Network identifier: 01554397) protocol. The protocol used a planning target volume and 2 primary organs at risk: pelvic bone marrow (PBM) and bowel. Secondary organs at risk were rectum and bladder. Initial unfiltered dose-volumemore » histogram (DVH) estimation models were trained using all 86 plans. Refined training sets were created by removing sub-optimal plans from the unfiltered sample, and DVH estimation models… and DVH estimation models were constructed by identifying 30 of 86 plans emphasizing PBM sparing (comparing protocol-specified dosimetric cutpoints V{sub 10} (percentage volume of PBM receiving at least 10 Gy dose) and V{sub 20} (percentage volume of PBM receiving at least 20 Gy dose) with unfiltered predictions) and another 30 of 86 plans emphasizing bowel sparing (comparing V{sub 40} (absolute volume of bowel receiving at least 40 Gy dose) and V{sub 45} (absolute volume of bowel receiving at least 45 Gy dose), 9 in common with the PBM set). To obtain deliverable KBP plans, refined models must inform patient-specific optimization objectives and/or priorities (an auto-planning “routine”). Four candidate routines emphasizing different tradeoffs were composed, and a script was developed to automatically re-plan multiple patients with each routine. After selection of the routine that best met protocol objectives in the 51-patient training sample (KBP{sub FINAL}), protocol-specific DVH metrics and normal tissue complication probability were compared for original versus KBP{sub FINAL} plans across the 35-patient validation set. Paired t tests were used to test differences between planning sets. Results: KBP{sub FINAL} plans outperformed manual planning across the validation set in all protocol-specific DVH cutpoints. The mean normal tissue complication probability for gastrointestinal toxicity was lower for KBP{sub FINAL} versus validation-set plans (48.7% vs 53.8%, P<.001). Similarly, the estimated mean white blood cell count nadir was higher (2.77 vs 2.49 k/mL, P<.001) with KBP{sub FINAL} plans, indicating lowered probability of hematologic toxicity. Conclusions: This work demonstrates that a KBP system can be efficiently trained and refined for use in radiation therapy clinical trials with minimal effort. This patient-specific plan quality control resulted in improvements on protocol-specific dosimetric endpoints.« less

Effects of music and music video interventions on sleep quality: A randomized controlled trial in adults with sleep disturbances.

PubMed

Huang, Chiung-Yu; Chang, En-Ting; Hsieh, Yuan-Mei; Lai, Hui-Ling

2017-10-01

The present study aimed to compare the effects of music and music video interventions on objective and subjective sleep quality in adults with sleep disturbances. A randomized controlled trial was performed on 71 adults who were recruited from the outpatient department of a hospital with 1100 beds and randomly assigned to the control, music, and music video groups. During the 4 test days (Days 2-5), for 30min before nocturnal sleep, the music group listened to Buddhist music and the music video group watched Buddhist music videos. They were instructed to not listen/watch to the music/MV on the first night (pretest, Day 1) and the final night (Day 6). The control group received no intervention. Sleep was assessed using a one-channel electroencephalography machine in their homes and self-reported questionnaires. The music and music video interventions had no effect on any objective sleep parameters, as measured using electroencephalography. However, the music group had significantly longer subjective total sleep time than the music video group did (Wald χ 2 =6.23, p=0.04). Our study results increase knowledge regarding music interventions for sleep quality in adults with sleep disturbances. This study suggested that more research is required to strengthen the scientific knowledge of the effects of music intervention on sleep quality in adults with sleep disturbances. (ISRCTN94971645). Copyright © 2017 Elsevier Ltd. All rights reserved.

Local anesthetics injection therapy for musculoskeletal disorders: a systematic review and meta-analysis.

PubMed

Mosshammer, Dirk; Mayer, Benjamin; Joos, Stefanie

2013-06-01

Therapeutic injections with local anesthetics (TLA) are widespread and are used for various symptoms of the musculoskeletal system. The aim of the present project was to evaluate the efficacy and safety of TLA in the treatment of musculoskeletal disorders. Systematic literature search for controlled clinical trials (Medline, Cochrane, CAMbase, hand search of references) without language limitation; independent screening of the search results (n=3200 hits), abstract reading, and full-text analysis by 2 reviewers. Two authors independently extracted the data and assessed study quality. Meta-analysis was calculated for studies using a continuous scale for pain assessment. Twenty-four controlled trials were included in this review. In almost all studies no primary outcome measure was defined and the overall study quality was low. The qualitative data analysis revealed no clear trend for or against TLA. The meta-analysis of 12 studies showed no significant difference in pain reduction for TLA compared with control treatments consisting of saline injections or other substances, oral analgesics, or nonpharmacological interventions (standardized mean difference -0.31, 95% confidence interval, -0.75 to 0.14). Minor adverse side effects were reported in 7 studies in both the TLA and the control groups with no trend for one of the groups to be safer. Despite the widespread use of TLA for musculoskeletal disorders in daily practice, available data are sparse and of low quality and, therefore, do not allow a final recommendation. High-quality studies are needed to close the gap between common practice and research.

In-line quality control of moving objects by means of spectral-domain OCT

NASA Astrophysics Data System (ADS)

Markl, Daniel; Hannesschläger, Günther; Buchsbaum, Andreas; Sacher, Stephan; Khinast, Johannes G.; Leitner, Michael

2014-08-01

In-line quality control of intermediate and final products is essential in various industries. This may imply determining the thickness of a foil or evaluating the homogeneity of coating applied to a pharmaceutical tablet. Such a qualitative and quantitative monitoring in a depth-resolved manner can be accomplished using optical coherence tomography (OCT). In-line quality control based on OCT requires additional consideration of motion effects for the system design as well as for data interpretation. This study focuses on transverse motion effects that can arise in spectral-domain (SD-) OCT systems. The impact of a transverse movement is analyzed for a constant relative speed difference up to 0.7 m/s between sample and sensor head. In particular, transverse motion is affecting OCT system properties such as the beam displacement (distance between adjacent A-scans) and transverse resolution. These properties were evaluated theoretically and experimentally for OCT images of a resolution target and pharmaceutical film-coated tablets. Both theoretical and experimental analyses highlight the shift of the transverse resolution limiting factor from the optics to the beam displacement above a relative speed difference between sensor head and sample of 0.42 m/s (for the presented SD-OCT setup). Speeds above 0.4 m/s are often demanded when monitoring industrial processes, such as a coating process when producing film-coated tablets. This emphasizes the importance of a fast data acquisition when using OCT as in-line quality control tool.

Effect of desensitizing toothpastes on dentine hypersensitivity: A systematic review and meta-analysis.

PubMed

Hu, Meng-Long; Zheng, Gang; Zhang, You-Dong; Yan, Xiang; Li, Xiao-Chan; Lin, Hong

2018-05-19

To evaluate the desensitizing effect of toothpastes that contain ingredients that act against dentine hypersensitivity (DH) and to compare this effect with negative controls. Five databases were searched to identify relevant articles published up to November 27, 2017. Randomized controlled trials (RCTs) comparing desensitizing toothpastes with a toothpastes without desensitizing component in adult patients that suffer from DH were included. The risk of bias was assessed according to the Cochrane guidelines, and the quality of the evidence was evaluated using the GRADE tool. Inverse variance random-effects meta-analyses of standardized mean differences (SMD) and 95% confidence intervals (CIs) were calculated using RevMan 5.3 software. 53 RCTs with 4796 patients were finally included in the meta-analysis. The toothpastes that contain active desensitization ingredients showed a better desensitizing effect on DH than the negative control, except the strontium- and amorphous calcium phosphate-containing toothpastes. The amorphous calcium phosphate-containing toothpaste had very low-quality evidence, the strontium, potassium and strontium, and potassium and stannous fluoride-containing toothpastes had low-quality evidence, and the other five toothpastes had moderate quality evidence. Our result support the premise that toothpastes containing potassium, stannous fluoride, potassium and strontium, potassium and stannous fluoride, calcium sodium phosphosilicate, arginine, and nano-hydroxyapatite relieve the symptoms of DH, but does not advise the use of toothpastes that contain strontium and amorphous calcium phosphate. Furthermore, high-quality studies are needed to confirm our results. (PROSPERO CRD42018085639). Copyright © 2018 Elsevier Ltd. All rights reserved.

Meeting the requirements of importing countries: practice and policy for on-farm approaches to food safety.

PubMed

Dagg, P J; Butler, R J; Murray, J G; Biddle, R R

2006-08-01

In light of the increasing consumer demand for safe, high-quality food and recent public health concerns about food-borne illness, governments and agricultural industries are under pressure to provide comprehensive food safety policies and programmes consistent with international best practice. Countries that export food commodities derived from livestock must meet both the requirements of the importing country and domestic standards. It is internationally accepted that end-product quality control, and similar methods aimed at ensuring food safety, cannot adequately ensure the safety of the final product. To achieve an acceptable level of food safety, governments and the agricultural industry must work collaboratively to provide quality assurance systems, based on sound risk management principles, throughout the food supply chain. Quality assurance systems on livestock farms, as in other parts of the food supply chain, should address food safety using hazard analysis critical control point principles. These systems should target areas including biosecurity, disease monitoring and reporting, feedstuff safety, the safe use of agricultural and veterinary chemicals, the control of potential food-borne pathogens and traceability. They should also be supported by accredited training programmes, which award certification on completion, and auditing programmes to ensure that both local and internationally recognised guidelines and standards continue to be met. This paper discusses the development of policies for on-farm food safety measures and their practical implementation in the context of quality assurance programmes, using the Australian beef industry as a case study.

Post Processing Methods used to Improve Surface Finish of Products which are Manufactured by Additive Manufacturing Technologies: A Review

NASA Astrophysics Data System (ADS)

Kumbhar, N. N.; Mulay, A. V.

2016-08-01

The Additive Manufacturing (AM) processes open the possibility to go directly from Computer-Aided Design (CAD) to a physical prototype. These prototypes are used as test models before it is finalized as well as sometimes as a final product. Additive Manufacturing has many advantages over the traditional process used to develop a product such as allowing early customer involvement in product development, complex shape generation and also save time as well as money. Additive manufacturing also possess some special challenges that are usually worth overcoming such as Poor Surface quality, Physical Properties and use of specific raw material for manufacturing. To improve the surface quality several attempts had been made by controlling various process parameters of Additive manufacturing and also applying different post processing techniques on components manufactured by Additive manufacturing. The main objective of this work is to document an extensive literature review in the general area of post processing techniques which are used in Additive manufacturing.

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi Method

NASA Astrophysics Data System (ADS)

Hazza Faizi Al-Hazza, Muataz; Ibrahim, Nur Asmawiyah bt; Adesta, Erry T. Y.; Khan, Ahsan Ali; Abdullah Sidek, Atiah Bt.

2017-03-01

One of the main challenges for any manufacturer is how to decrease the machining cost without affecting the final quality of the product. One of the new advanced machining processes in industry is the high speed hard end milling process that merges three advanced machining processes: high speed milling, hard milling and dry milling. However, one of the most important challenges in this process is to control the flank wear rate. Therefore a analyzing the flank wear rate during machining should be investigated in order to determine the best cutting levels that will not affect the final quality of the product. In this research Taguchi method has been used to investigate the effect of cutting speed, feed rate and depth of cut and determine the best level s to minimize the flank wear rate up to total length of 0.3mm based on the ISO standard to maintain the finishing requirements.

Gluten-free breads and cookies of raw and popped amaranth flours with attractive technological and nutritional qualities.

PubMed

de la Barca, Ana María Calderón; Rojas-Martínez, María Elvira; Islas-Rubio, Alma Rosa; Cabrera-Chávez, Francisco

2010-09-01

Gluten-free bakery foodstuffs are a challenge for technologists and nutritionists since alternative ingredients used in their formulations have poor functional and nutritional properties. Therefore, gluten-free bread and cookies using raw and popped amaranth, a grain with high quality nutrients and promising functional properties, were formulated looking for the best combinations. The best formulation for bread included 60-70% popped amaranth flour and 30-40% raw amaranth flour which produced loaves with homogeneous crumb and higher specific volume (3.5 ml/g) than with other gluten-free breads. The best cookies recipe had 20% of popped amaranth flour and 13% of whole-grain popped amaranth. The expansion factor was similar to starch-based controls and the hardness was similar (10.88 N) to other gluten-free cookies. Gluten content of the final products was around 12 ppm. The functionality of amaranth-based doughs was acceptable although hydrocolloids were not added and the final gluten-free products had a high nutritional value.

The development of an audit technique to assess the quality of safety barrier management.

PubMed

Guldenmund, Frank; Hale, Andrew; Goossens, Louis; Betten, Jeroen; Duijm, Nijs Jan

2006-03-31

This paper describes the development of a management model to control barriers devised to prevent major hazard scenarios. Additionally, an audit technique is explained that assesses the quality of such a management system. The final purpose of the audit technique is to quantify those aspects of the management system that have a direct impact on the reliability and effectiveness of the barriers and, hence, the probability of the scenarios involved. First, an outline of the management model is given and its elements are explained. Then, the development of the audit technique is described. Because the audit technique uses actual major hazard scenarios and barriers within these as its focus, the technique achieves a concreteness and clarity that many other techniques often lack. However, this strength is also its limitation, since the full safety management system is not covered with the technique. Finally, some preliminary experiences obtained from several test sites are compiled and discussed.

Laser light-section sensor automating the production of textile-reinforced composites

NASA Astrophysics Data System (ADS)

Schmitt, R.; Niggemann, C.; Mersmann, C.

2009-05-01

Due to their advanced weight-specific mechanical properties, the application of fibre-reinforced plastics (FRP) has been established as a key technology in several engineering areas. Textile-based reinforcement structures (Preform) in particular achieve a high structural integrity due to the multi-dimensional build-up of dry-fibre layers combined with 3D-sewing and further textile processes. The final composite parts provide enhanced damage tolerances through excellent crash-energy absorbing characteristics. For these reasons, structural parts (e.g. frame) will be integrated in next generation airplanes. However, many manufacturing processes for FRP are still involving manual production steps without integrated quality control. The non-automated production implies considerable process dispersion and a high rework rate. Before the final inspection there is no reliable information about the production status. This work sets metrology as the key to automation and thus an economically feasible production, applying a laser light-section sensor system (LLSS) to measure process quality and feed back the results to close control loops of the production system. The developed method derives 3D-measurements from height profiles acquired by the LLSS. To assure the textile's quality a full surface scan is conducted, detecting defects or misalignment by comparing the measurement results with a CAD model of the lay-up. The method focuses on signal processing of the height profiles to ensure a sub-pixel accuracy using a novel algorithm based on a non-linear least-square fitting to a set of sigmoid functions. To compare the measured surface points to the CAD model, material characteristics are incorporated into the method. This ensures that only the fibre layer of the textile's surface is included and gaps between the fibres or overlaying seams are neglected. Finally, determining the uncertainty in measurement according to the GUM-standard proofed the sensor system's accuracy. First tests under industrial conditions showed that applying this sensor after the drapery of each textile layer reduces the scrap quota by approximately 30%.

Announcement—guidance document for acquiring reliable data in ecological restoration projects

USGS Publications Warehouse

Stapanian, Martin A.; Rodriguez, Karen; Lewis, Timothy E.; Blume, Louis; Palmer, Craig J.; Walters, Lynn; Schofield, Judith; Amos, Molly M.; Bucher, Adam

2016-01-01

The Laurentian Great Lakes are undergoing intensive ecological restoration in Canada and the United States. In the United States, an interagency committee was formed to facilitate implementation of quality practices for federally funded restoration projects in the Great Lakes basin. The Committee's responsibilities include developing a guidance document that will provide a common approach to the application of quality assurance and quality control (QA/QC) practices for restoration projects. The document will serve as a “how-to” guide for ensuring data quality during each aspect of ecological restoration projects. In addition, the document will provide suggestions on linking QA/QC data with the routine project data and hints on creating detailed supporting documentation. Finally, the document will advocate integrating all components of the project, including QA/QC applications, into an overarching decision-support framework. The guidance document is expected to be released by the U.S. EPA Great Lakes National Program Office in 2017.

Light-leaking region segmentation of FOG fiber based on quality evaluation of infrared image

NASA Astrophysics Data System (ADS)

Liu, Haoting; Wang, Wei; Gao, Feng; Shan, Lianjie; Ma, Yuzhou; Ge, Wenqian

2014-07-01

To improve the assembly reliability of Fiber Optic Gyroscope (FOG), a light leakage detection system and method is developed. First, an agile movement control platform is designed to implement the pose control of FOG optical path component in 6 Degrees of Freedom (DOF). Second, an infrared camera is employed to capture the working state images of corresponding fibers in optical path component after the manual assembly of FOG; therefore the entire light transmission process of key sections in light-path can be recorded. Third, an image quality evaluation based region segmentation method is developed for the light leakage images. In contrast to the traditional methods, the image quality metrics, including the region contrast, the edge blur, and the image noise level, are firstly considered to distinguish the image characters of infrared image; then the robust segmentation algorithms, including graph cut and flood fill, are all developed for region segmentation according to the specific image quality. Finally, after the image segmentation of light leakage region, the typical light-leaking type, such as the point defect, the wedge defect, and the surface defect can be identified. By using the image quality based method, the applicability of our proposed system can be improved dramatically. Many experiment results have proved the validity and effectiveness of this method.

[Quality management (TQM) in public health-care (PHC): principles for cost-performance calculations and cost reductions with better quality].

PubMed

Bergholz, W

2008-11-01

In many high-tech industries, quality management (QM) has enabled improvements of quality by a factor of 100 or more, in combination with significant cost reductions. Compared to this, the application of QM methods in health care is in its initial stages. It is anticipated that stringent process management, embedded in an effective QM system will lead to significant improvements in health care in general and in the German public health service in particular. Process management is an ideal platform for controlling in the health care sector, and it will significantly improve the leverage of controlling to bring down costs. Best practice sharing in industry has led to quantum leap improvements. Process management will enable best practice sharing also in the public health service, in spite of the highly diverse portfolio of services that the public health service offers in different German regions. Finally, it is emphasised that "technical" QM, e.g., on the basis of the ISO 9001 standard is not sufficient to reach excellence. It is necessary to integrate soft factors, such as patient or employee satisfaction, and leadership quality into the system. The EFQM model for excellence can serve as proven tool to reach this goal.

An Investigation of Large Tilt-Rotor Hover and Low Speed Handling Qualities

NASA Technical Reports Server (NTRS)

Malpica, Carlos A.; Decker, William A.; Theodore, Colin R.; Lindsey, James E.; Lawrence, Ben; Blanken, Chris L.

2011-01-01

A piloted simulation experiment conducted on the NASA-Ames Vertical Motion Simulator evaluated the hover and low speed handling qualities of a large tilt-rotor concept, with particular emphasis on longitudinal and lateral position control. Ten experimental test pilots evaluated different combinations of Attitude Command-Attitude Hold (ACAH) and Translational Rate Command (TRC) response types, nacelle conversion actuator authority limits and inceptor choices. Pilots performed evaluations in revised versions of the ADS-33 Hover, Lateral Reposition and Depart/Abort MTEs and moderate turbulence conditions. Level 2 handling qualities ratings were primarily recorded using ACAH response type in all three of the evaluation maneuvers. The baseline TRC conferred Level 1 handling qualities in the Hover MTE, but there was a tendency to enter into a PIO associated with nacelle actuator rate limiting when employing large, aggressive control inputs. Interestingly, increasing rate limits also led to a reduction in the handling qualities ratings. This led to the identification of a nacelle rate to rotor longitudinal flapping coupling effect that induced undesired, pitching motions proportional to the allowable amount of nacelle rate. A modification that counteracted this effect significantly improved the handling qualities. Evaluation of the different response type variants showed that inclusion of TRC response could provide Level 1 handling qualities in the Lateral Reposition maneuver by reducing coupled pitch and heave off axis responses that otherwise manifest with ACAH. Finally, evaluations in the Depart/Abort maneuver showed that uncertainty about commanded nacelle position and ensuing aircraft response, when manually controlling the nacelle, demanded high levels of attention from the pilot. Additional requirements to maintain pitch attitude within 5 deg compounded the necessary workload.

Air Quality Criteria for Ozone and Related Photochemical Oxidants (Final Report, 2006)

EPA Science Inventory

In February 2006, EPA released the final document, Air Quality Criteria for Ozone and Other Photochemical Oxidants. Tropospheric or surface-level ozone (O3) is one of six major air pollutants regulated by National Ambient Air Quality Standards (NAAQS) under the U.S...

A comparative study of quality and safety of Atlantic cod (Gadus morhua) fillets during cold storage, as affected by different thawing methods of pre‐rigor frozen headed and gutted fish

PubMed Central

Jónsson, Ásbjörn; Backi, Christoph Josef; Lunestad, Bjørn Tore; Karlsdóttir, Magnea G

2017-01-01

Abstract BACKGROUND The catch of marine whitefish is typically seasonal, whereas the land‐based processing industry has a need for all‐year stable supply of raw materials. This challenge can be met by applying fish frozen at sea. When using frozen fish, the methods employed for thawing may influence the safety and quality of the final product. This study aimed to investigate the applicability of novel thawing strategies in order to provide an all‐year supply of high‐quality and safe cod products. RESULTS Comparative investigations of quality and safety factors after thawing in water, with and without air circulation, and contact thawing were performed. The parameters included water‐holding capacity, thawing loss, drip loss, cooking yield, sensory evaluation and microbiological analyses (including total volatile bases nitrogen). Water thawing with air circulation provided faster thawing than water thawing without air circulation and contact thawing. For all three methods, the quality of the thawed fish was acceptable and the shelf life of the fillets during chilled storage was between 10 and 14 days post‐filleting. CONCLUSION The results show that controlled freezing of cod, followed by appropriate thawing, may provide the processing industry with an all‐year delivery of raw materials, without compromising quality and safety of the final product. © 2017 The Authors. Journal of The Science of Food and Agriculture published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry. PMID:28862323

Analysis of Aircraft Control Performance using a Fuzzy Rule Base Representation of the Cooper-Harper Aircraft Handling Quality Rating

NASA Technical Reports Server (NTRS)

Tseng, Chris; Gupta, Pramod; Schumann, Johann

2006-01-01

The Cooper-Harper rating of Aircraft Handling Qualities has been adopted as a standard for measuring the performance of aircraft since it was introduced in 1966. Aircraft performance, ability to control the aircraft, and the degree of pilot compensation needed are three major key factors used in deciding the aircraft handling qualities in the Cooper- Harper rating. We formulate the Cooper-Harper rating scheme as a fuzzy rule-based system and use it to analyze the effectiveness of the aircraft controller. The automatic estimate of the system-level handling quality provides valuable up-to-date information for diagnostics and vehicle health management. Analyzing the performance of a controller requires a set of concise design requirements and performance criteria. Ir, the case of control systems fm a piloted aircraft, generally applicable quantitative design criteria are difficult to obtain. The reason for this is that the ultimate evaluation of a human-operated control system is necessarily subjective and, with aircraft, the pilot evaluates the aircraft in different ways depending on the type of the aircraft and the phase of flight. In most aerospace applications (e.g., for flight control systems), performance assessment is carried out in terms of handling qualities. Handling qualities may be defined as those dynamic and static properties of a vehicle that permit the pilot to fully exploit its performance in a variety of missions and roles. Traditionally, handling quality is measured using the Cooper-Harper rating and done subjectively by the human pilot. In this work, we have formulated the rules of the Cooper-Harper rating scheme as fuzzy rules with performance, control, and compensation as the antecedents, and pilot rating as the consequent. Appropriate direct measurements on the controller are related to the fuzzy Cooper-Harper rating system: a stability measurement like the rate of change of the cost function can be used as an indicator if the aircraft is under control; the tracking error is a good measurement for performance needed in the rating scheme. Finally, the change of the control amount or the output of a confidence tool, which has been developed by the authors, can be used as an indication of pilot compensation. We use a number of known aircraft flight scenarios with known pilot ratings to calibrate our fuzzy membership functions. These include normal flight conditions and situations in which partial or complete failure of tail, aileron, engine, or throttle occurs.

Columbia/Willamette Skill Builders Consortium. Final Performance Report. Appendix 5B Anodizing Inc. (Aluminum Extrusion Manufacturing). Basic Measurement Math. Instructors' Reports and Sample Curriculum Materials.

ERIC Educational Resources Information Center

Taylor, Marjorie; And Others

Anodizing, Inc., Teamsters Local 162, and Mt. Hood Community College (Oregon) developed a workplace literacy program for workers at Anodizing. These workers did not have the basic skill competencies to benefit from company training efforts in statistical process control and quality assurance and were not able to advance to lead and supervisory…

Final Environmental Assessment Addressing Tree Management at Dobbins Air Reserve Base, Georgia

DTIC Science & Technology

2013-09-01

metamorphic rocks . The Piedmont also contains an abundance of mineral resources such as stone, granite, and soapstone. A major geologic feature of this...rich igneous and metamorphic rocks . Natural Resources Conservation Service soil surveys indicate that soils on and around Dobbins ARB are...Plant-6 AFRC Air Force Reserve Command AICUZ Air Installation Compatible Use Zone APZ Accident Potential Zone AQCR Air Quality Control Region ARB

Generation of an annotated reference standard for vaccine adverse event reports.

PubMed

Foster, Matthew; Pandey, Abhishek; Kreimeyer, Kory; Botsis, Taxiarchis

2018-07-05

As part of a collaborative project between the US Food and Drug Administration (FDA) and the Centers for Disease Control and Prevention for the development of a web-based natural language processing (NLP) workbench, we created a corpus of 1000 Vaccine Adverse Event Reporting System (VAERS) reports annotated for 36,726 clinical features, 13,365 temporal features, and 22,395 clinical-temporal links. This paper describes the final corpus, as well as the methodology used to create it, so that clinical NLP researchers outside FDA can evaluate the utility of the corpus to aid their own work. The creation of this standard went through four phases: pre-training, pre-production, production-clinical feature annotation, and production-temporal annotation. The pre-production phase used a double annotation followed by adjudication strategy to refine and finalize the annotation model while the production phases followed a single annotation strategy to maximize the number of reports in the corpus. An analysis of 30 reports randomly selected as part of a quality control assessment yielded accuracies of 0.97, 0.96, and 0.83 for clinical features, temporal features, and clinical-temporal associations, respectively and speaks to the quality of the corpus. Copyright © 2018 Elsevier Ltd. All rights reserved.

Decentralized coordinated control of elastic web winding systems without tension sensor.

PubMed

Hou, Hailiang; Nian, Xiaohong; Chen, Jie; Xiao, Dengfeng

2018-06-26

In elastic web winding systems, precise regulation of web tension in each span is critical to ensure final product quality, and to achieve low cost by reducing the occurrence of web break or fold. Generally, web winding systems use load cells or swing rolls as tension sensors, which add cost, reduce system reliability and increase the difficulty of control. In this paper, a decentralized coordinated control scheme with tension observers is designed for a three-motor web-winding system. First, two tension observers are proposed to estimate the unwinding and winding tension. The designed observers consider the essential dynamic, radius, and inertial variation effects and only require the modest computational effort. Then, using the estimated tensions as feedback signals, a robust decentralized coordinated controller is adopted to reduce the interaction between subsystems. Asymptotic stabilities of the observer error dynamics and the closed-loop winding systems are demonstrated via Lyapunov stability theory. The observer gains and the controller gains can be obtained by solving matrix inequalities. Finally, some simulations and experiments are performed on a paper winding setup to test the performance of the designed observers and the observer-base DCC method, respectively. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Chemometrics-based process analytical technology (PAT) tools: applications and adaptation in pharmaceutical and biopharmaceutical industries.

PubMed

Challa, Shruthi; Potumarthi, Ravichandra

2013-01-01

Process analytical technology (PAT) is used to monitor and control critical process parameters in raw materials and in-process products to maintain the critical quality attributes and build quality into the product. Process analytical technology can be successfully implemented in pharmaceutical and biopharmaceutical industries not only to impart quality into the products but also to prevent out-of-specifications and improve the productivity. PAT implementation eliminates the drawbacks of traditional methods which involves excessive sampling and facilitates rapid testing through direct sampling without any destruction of sample. However, to successfully adapt PAT tools into pharmaceutical and biopharmaceutical environment, thorough understanding of the process is needed along with mathematical and statistical tools to analyze large multidimensional spectral data generated by PAT tools. Chemometrics is a chemical discipline which incorporates both statistical and mathematical methods to obtain and analyze relevant information from PAT spectral tools. Applications of commonly used PAT tools in combination with appropriate chemometric method along with their advantages and working principle are discussed. Finally, systematic application of PAT tools in biopharmaceutical environment to control critical process parameters for achieving product quality is diagrammatically represented.

Advanced manufacturing development of a composite empennage component for L-1011 aircraft

NASA Technical Reports Server (NTRS)

Alva, T.; Henkel, J.; Johnson, R.; Carll, B.; Jackson, A.; Mosesian, B.; Brozovic, R.; Obrien, R.; Eudaily, R.

1982-01-01

This is the final report of technical work conducted during the fourth phase of a multiphase program having the objective of the design, development and flight evaluation of an advanced composite empennage component manufactured in a production environment at a cost competitive with those of its metal counterpart, and at a weight savings of at least 20 percent. The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes front and rear spars. During Phase 4 of the program, production quality tooling was designed and manufactured to produce three sets of covers, ribs, spars, miscellaneous parts, and subassemblies to assemble three complete ACVF units. Recurring and nonrecurring cost data were compiled and documented in the updated producibility/design to cost plan. Nondestruct inspections, quality control tests, and quality acceptance tests were performed in accordance with the quality assurance plan and the structural integrity control plan. Records were maintained to provide traceability of material and parts throughout the manufacturing development phase. It was also determined that additional tooling would not be required to support the current and projected L-1011 production rate.

Advanced control of dissolved oxygen concentration in fed batch cultures during recombinant protein production.

PubMed

Kuprijanov, A; Gnoth, S; Simutis, R; Lübbert, A

2009-02-01

Design and experimental validation of advanced pO(2) controllers for fermentation processes operated in the fed-batch mode are described. In most situations, the presented controllers are able to keep the pO(2) in fermentations for recombinant protein productions exactly on the desired value. The controllers are based on the gain-scheduling approach to parameter-adaptive proportional-integral controllers. In order to cope with the most often appearing distortions, the basic gain-scheduling feedback controller was complemented with a feedforward control component. This feedforward/feedback controller significantly improved pO(2) control. By means of numerical simulations, the controller behavior was tested and its parameters were determined. Validation runs were performed with three Escherichia coli strains producing different recombinant proteins. It is finally shown that the new controller leads to significant improvements in the signal-to-noise ratio of other key process variables and, thus, to a higher process quality.

Composite adaptive control of belt polishing force for aero-engine blade

NASA Astrophysics Data System (ADS)

Zhsao, Pengbing; Shi, Yaoyao

2013-09-01

The existing methods for blade polishing mainly focus on robot polishing and manual grinding. Due to the difficulty in high-precision control of the polishing force, the blade surface precision is very low in robot polishing, in particular, quality of the inlet and exhaust edges can not satisfy the processing requirements. Manual grinding has low efficiency, high labor intensity and unstable processing quality, moreover, the polished surface is vulnerable to burn, and the surface precision and integrity are difficult to ensure. In order to further improve the profile accuracy and surface quality, a pneumatic flexible polishing force-exerting mechanism is designed and a dual-mode switching composite adaptive control(DSCAC) strategy is proposed, which combines Bang-Bang control and model reference adaptive control based on fuzzy neural network(MRACFNN) together. By the mode decision-making mechanism, Bang-Bang control is used to track the control command signal quickly when the actual polishing force is far away from the target value, and MRACFNN is utilized in smaller error ranges to improve the system robustness and control precision. Based on the mathematical model of the force-exerting mechanism, simulation analysis is implemented on DSCAC. Simulation results show that the output polishing force can better track the given signal. Finally, the blade polishing experiments are carried out on the designed polishing equipment. Experimental results show that DSCAC can effectively mitigate the influence of gas compressibility, valve dead-time effect, valve nonlinear flow, cylinder friction, measurement noise and other interference on the control precision of polishing force, which has high control precision, strong robustness, strong anti-interference ability and other advantages compared with MRACFNN. The proposed research achieves high-precision control of the polishing force, effectively improves the blade machining precision and surface consistency, and significantly reduces the surface roughness.

An Integrated Framework for Multipollutant Air Quality Management and Its Application in Georgia

NASA Astrophysics Data System (ADS)

Cohan, Daniel S.; Boylan, James W.; Marmur, Amit; Khan, Maudood N.

2007-10-01

Air protection agencies in the United States increasingly confront non-attainment of air quality standards for multiple pollutants sharing interrelated emission origins. Traditional approaches to attainment planning face important limitations that are magnified in the multipollutant context. Recognizing those limitations, the Georgia Environmental Protection Division has adopted an integrated framework to address ozone, fine particulate matter, and regional haze in the state. Rather than applying atmospheric modeling merely as a final check of an overall strategy, photochemical sensitivity analysis is conducted upfront to compare the effectiveness of controlling various precursor emission species and source regions. Emerging software enables the modeling of health benefits and associated economic valuations resulting from air pollution control. Photochemical sensitivity and health benefits analyses, applied together with traditional cost and feasibility assessments, provide a more comprehensive characterization of the implications of various control options. The fuller characterization both informs the selection of control options and facilitates the communication of impacts to affected stakeholders and the public. Although the integrated framework represents a clear improvement over previous attainment-planning efforts, key remaining shortcomings are also discussed.

An integrated framework for multipollutant air quality management and its application in Georgia.

PubMed

Cohan, Daniel S; Boylan, James W; Marmur, Amit; Khan, Maudood N

2007-10-01

Air protection agencies in the United States increasingly confront non-attainment of air quality standards for multiple pollutants sharing interrelated emission origins. Traditional approaches to attainment planning face important limitations that are magnified in the multipollutant context. Recognizing those limitations, the Georgia Environmental Protection Division has adopted an integrated framework to address ozone, fine particulate matter, and regional haze in the state. Rather than applying atmospheric modeling merely as a final check of an overall strategy, photochemical sensitivity analysis is conducted upfront to compare the effectiveness of controlling various precursor emission species and source regions. Emerging software enables the modeling of health benefits and associated economic valuations resulting from air pollution control. Photochemical sensitivity and health benefits analyses, applied together with traditional cost and feasibility assessments, provide a more comprehensive characterization of the implications of various control options. The fuller characterization both informs the selection of control options and facilitates the communication of impacts to affected stakeholders and the public. Although the integrated framework represents a clear improvement over previous attainment-planning efforts, key remaining shortcomings are also discussed.

Neuropsychiatric symptoms and quality of life in patients in the final phase of dementia.

PubMed

Koopmans, Raymond T C M; van der Molen, Marloes; Raats, Monique; Ettema, Teake P

2009-01-01

To assess neuropsychiatric symptoms and quality of life in a group of patients in the final phase of dementia. All patients with dementia (n = 216) residing on dementia special care units of two Dutch nursing homes were included in the study provided they met the criteria for the final phase of dementia. Neuropsychiatric symptoms were assessed with the Neuropsychiatric Inventory Nursing Home version (NPI-NH) and the Cohen Mansfield Agitation Inventory (CMAI). Quality of life was assessed with the QUALIDEM. Of the 216 dementia patients 39 met the criteria for the final phase of dementia. The patients showed a specific pattern of behaviours with a high prevalence of apathy, agitation and behaviours that were mainly observed during morning care such as making strange noises, grabbing, performing repetitious mannerism, spitting, hitting, screaming and pushing. Overall quality of life of these patients in the final phase of dementia was moderate. In this small sample, patients in the final phase of dementia show specific behavioural problems, that mainly should be addressed with psychosocial interventions. (c) 2008 John Wiley & Sons, Ltd.

Higher prices, higher quality? Evidence from German nursing homes.

PubMed

Herr, Annika; Hottenrott, Hanna

2016-02-01

This study investigates the relationship between prices and quality of 7400 German nursing homes. We use a cross section of public quality reports for all German nursing homes, which had been evaluated between 2010 and 2013 by external institutions. Our analysis is based on multivariate regressions in a two stage least squares framework, where we instrument prices to explain their effect on quality controlling for income, nursing home density, demographics, labour market characteristics, and infrastructure at the regional level. Descriptive analysis shows that prices and quality do not only vary across nursing homes, but also across counties and federal states and that quality and prices correlate positively. Second, the econometric analysis, which accounts for the endogenous relation between negotiated price and reported quality, shows that quality indeed positively depends on prices. In addition, more places in nursing homes per people in need are correlated with both lower prices and higher quality. Finally, unobserved factors at the federal state level capture some of the variation of reported quality across nursing homes. Our results suggest that higher prices increase quality. Furthermore, since reported quality and prices vary substantially across federal states, we conclude that the quality and prices of long-term care facilities may well be compared within federal states but not across. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Inflammatory bowel disease and patterns of volatile organic compounds in the exhaled breath of children: A case-control study using Ion Molecule Reaction-Mass Spectrometry.

PubMed

Monasta, Lorenzo; Pierobon, Chiara; Princivalle, Andrea; Martelossi, Stefano; Marcuzzi, Annalisa; Pasini, Francesco; Perbellini, Luigi

2017-01-01

Inflammatory bowel diseases (IBD) profoundly affect quality of life and have been gradually increasing in incidence, prevalence and severity in many areas of the world, and in children in particular. Patients with suspected IBD require careful history and clinical examination, while definitive diagnosis relies on endoscopic and histological findings. The aim of the present study was to investigate whether the alveolar air of pediatric patients with IBD presents a specific volatile organic compounds' (VOCs) pattern when compared to controls. Patients 10-17 years of age, were divided into four groups: Crohn's disease (CD), ulcerative colitis (UC), controls with gastrointestinal symptomatology, and surgical controls with no evidence of gastrointestinal problems. Alveolar breath was analyzed by ion molecule reaction mass spectrometry. Four models were built starting from 81 molecules plus the age of subjects as independent variables, adopting a penalizing LASSO logistic regression approach: 1) IBDs vs. controls, finally based on 18 VOCs plus age (sensitivity = 95%, specificity = 69%, AUC = 0.925); 2) CD vs. UC, finally based on 13 VOCs plus age (sensitivity = 94%, specificity = 76%, AUC = 0.934); 3) IBDs vs. gastroenterological controls, finally based on 15 VOCs plus age (sensitivity = 94%, specificity = 65%, AUC = 0.918); 4) IBDs vs. controls, built starting from the 21 directly or indirectly calibrated molecules only, and finally based on 12 VOCs plus age (sensitivity = 94%, specificity = 71%, AUC = 0.888). The molecules identified by the models were carefully studied in relation to the concerned outcomes. This study, with the creation of models based on VOCs profiles, precise instrumentation and advanced statistical methods, can contribute to the development of new non-invasive, fast and relatively inexpensive diagnostic tools, with high sensitivity and specificity. It also represents a crucial step towards gaining further insights on the etiology of IBD through the analysis of specific molecules which are the expression of the particular metabolism that characterizes these patients.

Comparative evaluation of rumen-protected fat, coconut oil and various oilseeds supplemented to fattening bulls. 1. Effects on growth, carcass and meat quality.

PubMed

Sutter, F; Casutt, M M; Ossowski, D A; Scheeder, M R; Kreuzer, M

2000-01-01

Growth performance, carcass and meat quality were determined in 36 fattening Brown Swiss bulls fed with maize silage-hay-concentrate based rations supplemented with fats and various oilseeds. The concentrate diet in the control group contained only barley and soybean meal, while the treated groups included, as partial replacement of the concentrate, rumen-protected crystalline fat, coconut oil, whole crushed rapeseed, sunflower seed or linseed, providing additional 3% fat of total ration dry matter. Animals were housed in groups of six with one representative of each treatment in a monofactorial design and feed was offered using transponder controlled equipment. Daily gains were similar for control, protected fat, rapeseed and linseed treatments (1240 g/d on average), but were lower (P < 0.05) with sunflower seed (1135 g/d) and coconut oil (1038 g/d). Corresponding differences (P < 0.05) in carcass weights were observed. All fat supplemented groups had reduced rumen fluid protozoa counts (P < 0.05). Carcasses tended to be leaner with the fat supplements. Mostly no significant effects on other carcass quality (dressing percentage, conformation score) and meat quality traits (final pH, cooking loss, shear forces) as well as composition (dry matter, fat, collagen) occurred. Consequently, rumen protected fat and some oilseeds can be recommended to be fed to growing cattle as energy sources.

Characterizing air quality data from complex network perspective.

PubMed

Fan, Xinghua; Wang, Li; Xu, Huihui; Li, Shasha; Tian, Lixin

2016-02-01

Air quality depends mainly on changes in emission of pollutants and their precursors. Understanding its characteristics is the key to predicting and controlling air quality. In this study, complex networks were built to analyze topological characteristics of air quality data by correlation coefficient method. Firstly, PM2.5 (particulate matter with aerodynamic diameter less than 2.5 μm) indexes of eight monitoring sites in Beijing were selected as samples from January 2013 to December 2014. Secondly, the C-C method was applied to determine the structure of phase space. Points in the reconstructed phase space were considered to be nodes of the network mapped. Then, edges were determined by nodes having the correlation greater than a critical threshold. Three properties of the constructed networks, degree distribution, clustering coefficient, and modularity, were used to determine the optimal value of the critical threshold. Finally, by analyzing and comparing topological properties, we pointed out that similarities and difference in the constructed complex networks revealed influence factors and their different roles on real air quality system.

Does Glycemic Variability Impact Mood and Quality of Life?

PubMed Central

Quinn, Lauretta; Byrn, Mary; Ferrans, Carol; Miller, Michael; Strange, Poul

2012-01-01

Abstract Background Diabetes is a chronic condition that significantly impacts quality of life. Poor glycemic control is associated with more diabetes complications, depression, and worse quality of life. The impact of glycemic variability on mood and quality of life has not been studied. Methods A descriptive exploratory design was used. Twenty-three women with type 2 diabetes wore a continuous glucose monitoring system for 72 h and completed a series of questionnaires. Measurements included (1) glycemic control shown by glycated hemoglobin and 24-h mean glucose, (2) glycemic variability shown by 24-h SD of the glucose readings, continuous overall net glycemic action (CONGA), and Fourier statistical models to generate smoothed curves to assess rate of change defined as “energy,” and (3) mood (depression, anxiety, anger) and quality of life by questionnaires. Results Women with diabetes and co-morbid depression had higher anxiety, more anger, and lower quality of life than those without depression. Certain glycemic variability measures were associated with mood and quality of life. The 24-h SD of the glucose readings and the CONGA measures were significantly associated with health-related quality of life after adjusting for age and weight. Fourier models indicated that certain energy components were significantly associated with depression, trait anxiety, and overall quality of life. Finally, subjects with higher trait anxiety tended to have steeper glucose excursions. Conclusions Data suggest that greater glycemic variability may be associated with lower quality of life and negative moods. Implications include replication of the study in a larger sample for the assessment of blood glucose fluctuations as they impact mood and quality of life. PMID:22324383

Chicken meat quality: genetic variability and relationship with growth and muscle characteristics

PubMed Central

Le Bihan-Duval, Elisabeth; Debut, Martine; Berri, Cécile M; Sellier, Nadine; Santé-Lhoutellier, Véronique; Jégo, Yves; Beaumont, Catherine

2008-01-01

Background The qualitative properties of the meat are of major importance for poultry breeding, since meat is now widely consumed as cuts or as processed products. The aim of this study was to evaluate the genetic parameters of several breast meat quality traits and their genetic relationships with muscle characteristics in a heavy commercial line of broilers. Results Significant levels of heritability (averaging 0.3) were obtained for breast meat quality traits such as pH at 15 min post-slaughter, ultimate pH (pHu), color assessed by lightness L*, redness a* and yellowness b*, drip loss, thawing-cooking loss and shear-force. The rate of decrease in pH early post-mortem and the final pH of the meat were shown to be key factors of chicken meat quality. In particular, a decrease in the final pH led to paler, more exudative and tougher breast meat. The level of glycogen stored in breast muscle estimated by the Glycolytic Potential (GP) at slaughter time was shown to be highly heritable (h2 0.43). There was a very strong negative genetic correlation (rg) with ultimate meat pH (rg -0.97), suggesting a common genetic control for GP and pHu. While breast muscle weight was genetically positively correlated with fiber size (rg 0.76), it was negatively correlated with the level of glycogen stored in the muscle (rg -0.58), and as a consequence it was positively correlated with the final pH of the meat (rg 0.84). Conclusion This genetic study confirmed that selection should be useful to improve meat characteristics of meat-type chickens without impairing profitability because no genetic conflict was detected between meat quality and meat quantity. Moreover, the results suggested relevant selection criteria such as ultimate pH, which is strongly related to color, water-holding capacity and texture of the meat in this heavy chicken line. PMID:18706119

A Transparent and Transferable Framework for Tracking Quality Information in Large Datasets

PubMed Central

Smith, Derek E.; Metzger, Stefan; Taylor, Jeffrey R.

2014-01-01

The ability to evaluate the validity of data is essential to any investigation, and manual “eyes on” assessments of data quality have dominated in the past. Yet, as the size of collected data continues to increase, so does the effort required to assess their quality. This challenge is of particular concern for networks that automate their data collection, and has resulted in the automation of many quality assurance and quality control analyses. Unfortunately, the interpretation of the resulting data quality flags can become quite challenging with large data sets. We have developed a framework to summarize data quality information and facilitate interpretation by the user. Our framework consists of first compiling data quality information and then presenting it through 2 separate mechanisms; a quality report and a quality summary. The quality report presents the results of specific quality analyses as they relate to individual observations, while the quality summary takes a spatial or temporal aggregate of each quality analysis and provides a summary of the results. Included in the quality summary is a final quality flag, which further condenses data quality information to assess whether a data product is valid or not. This framework has the added flexibility to allow “eyes on” information on data quality to be incorporated for many data types. Furthermore, this framework can aid problem tracking and resolution, should sensor or system malfunctions arise. PMID:25379884

Final Environmental Assessment. Physical Fitness Center Los Angeles Air Force Base

DTIC Science & Technology

2000-10-13

Coast Air Quality Management District (SCAQMD). 1996. Final 1997 Air Qaulity Management Plan. November. South Coast Air Quality Management District...resources including land use, geology and soils, water resources, biological resources, air quality, noise, traffic and transportation, waste management ...3-8 3.8 Solid and Hazardous Waste Management and Disposal

Research of interaction between technological and material parameters during densification of sunflower hulls

NASA Astrophysics Data System (ADS)

Križan, Peter; Matúš, Miloš; Beniak, Juraj; Šooš, Ľubomír

2018-01-01

During the biomass densification can be recognized various technological variables and also material parameters which significantly influences the final solid biofuels (pellets) quality. In this paper, we will present the research findings concerning relationships between technological and material variables during densification of sunflower hulls. Sunflower hulls as an unused source is a typical product of agricultural industry in Slovakia and belongs to the group of herbaceous biomass. The main goal of presented experimental research is to determine the impact of compression pressure, compression temperature and material particle size distribution on final biofuels quality. Experimental research described in this paper was realized by single-axis densification, which was represented by experimental pressing stand. The impact of mentioned investigated variables on the final briquettes density and briquettes dilatation was determined. Mutual interactions of these variables on final briquettes quality are showing the importance of mentioned variables during the densification process. Impact of raw material particle size distribution on final biofuels quality was also proven by experimental research on semi-production pelleting plant.

Estimation and control of droplet size and frequency in projected spray mode of a gas metal arc welding (GMAW) process.

PubMed

Anzehaee, Mohammad Mousavi; Haeri, Mohammad

2011-07-01

New estimators are designed based on the modified force balance model to estimate the detaching droplet size, detached droplet size, and mean value of droplet detachment frequency in a gas metal arc welding process. The proper droplet size for the process to be in the projected spray transfer mode is determined based on the modified force balance model and the designed estimators. Finally, the droplet size and the melting rate are controlled using two proportional-integral (PI) controllers to achieve high weld quality by retaining the transfer mode and generating appropriate signals as inputs of the weld geometry control loop. Copyright © 2011 ISA. Published by Elsevier Ltd. All rights reserved.

Fermentanomics: Relating quality attributes of a monoclonal antibody to cell culture process variables and raw materials using multivariate data analysis.

PubMed

Rathore, Anurag S; Kumar Singh, Sumit; Pathak, Mili; Read, Erik K; Brorson, Kurt A; Agarabi, Cyrus D; Khan, Mansoor

2015-01-01

Fermentanomics is an emerging field of research and involves understanding the underlying controlled process variables and their effect on process yield and product quality. Although major advancements have occurred in process analytics over the past two decades, accurate real-time measurement of significant quality attributes for a biotech product during production culture is still not feasible. Researchers have used an amalgam of process models and analytical measurements for monitoring and process control during production. This article focuses on using multivariate data analysis as a tool for monitoring the internal bioreactor dynamics, the metabolic state of the cell, and interactions among them during culture. Quality attributes of the monoclonal antibody product that were monitored include glycosylation profile of the final product along with process attributes, such as viable cell density and level of antibody expression. These were related to process variables, raw materials components of the chemically defined hybridoma media, concentration of metabolites formed during the course of the culture, aeration-related parameters, and supplemented raw materials such as glucose, methionine, threonine, tryptophan, and tyrosine. This article demonstrates the utility of multivariate data analysis for correlating the product quality attributes (especially glycosylation) to process variables and raw materials (especially amino acid supplements in cell culture media). The proposed approach can be applied for process optimization to increase product expression, improve consistency of product quality, and target the desired quality attribute profile. © 2015 American Institute of Chemical Engineers.

Identification of long-term trends and seasonality in high-frequency water quality data from the Yangtze River basin, China.

PubMed

Duan, Weili; He, Bin; Chen, Yaning; Zou, Shan; Wang, Yi; Nover, Daniel; Chen, Wen; Yang, Guishan

2018-01-01

Comprehensive understanding of the long-term trends and seasonality of water quality is important for controlling water pollution. This study focuses on spatio-temporal distributions, long-term trends, and seasonality of water quality in the Yangtze River basin using a combination of the seasonal Mann-Kendall test and time-series decomposition. The used weekly water quality data were from 17 environmental stations for the period January 2004 to December 2015. Results show gradual improvement in water quality during this period in the Yangtze River basin and greater improvement in the Uppermost Yangtze River basin. The larger cities, with high GDP and population density, experienced relatively higher pollution levels due to discharge of industrial and household wastewater. There are higher pollution levels in Xiang and Gan River basins, as indicated by higher NH4-N and CODMn concentrations measured at the stations within these basins. Significant trends in water quality were identified for the 2004-2015 period. Operations of the three Gorges Reservoir (TGR) enhanced pH fluctuations and possibly attenuated CODMn, and NH4-N transportation. Finally, seasonal cycles of varying strength were detected for time-series of pollutants in river discharge. Seasonal patterns in pH indicate that maxima appear in winter, and minima in summer, with the opposite true for CODMn. Accurate understanding of long-term trends and seasonality are necessary goals of water quality monitoring system efforts and the analysis methods described here provide essential information for effectively controlling water pollution.

Evaluation of Various Radar Data Quality Control Algorithms Based on Accumulated Radar Rainfall Statistics

NASA Technical Reports Server (NTRS)

Robinson, Michael; Steiner, Matthias; Wolff, David B.; Ferrier, Brad S.; Kessinger, Cathy; Einaudi, Franco (Technical Monitor)

2000-01-01

The primary function of the TRMM Ground Validation (GV) Program is to create GV rainfall products that provide basic validation of satellite-derived precipitation measurements for select primary sites. A fundamental and extremely important step in creating high-quality GV products is radar data quality control. Quality control (QC) processing of TRMM GV radar data is based on some automated procedures, but the current QC algorithm is not fully operational and requires significant human interaction to assure satisfactory results. Moreover, the TRMM GV QC algorithm, even with continuous manual tuning, still can not completely remove all types of spurious echoes. In an attempt to improve the current operational radar data QC procedures of the TRMM GV effort, an intercomparison of several QC algorithms has been conducted. This presentation will demonstrate how various radar data QC algorithms affect accumulated radar rainfall products. In all, six different QC algorithms will be applied to two months of WSR-88D radar data from Melbourne, Florida. Daily, five-day, and monthly accumulated radar rainfall maps will be produced for each quality-controlled data set. The QC algorithms will be evaluated and compared based on their ability to remove spurious echoes without removing significant precipitation. Strengths and weaknesses of each algorithm will be assessed based on, their abilit to mitigate both erroneous additions and reductions in rainfall accumulation from spurious echo contamination and true precipitation removal, respectively. Contamination from individual spurious echo categories will be quantified to further diagnose the abilities of each radar QC algorithm. Finally, a cost-benefit analysis will be conducted to determine if a more automated QC algorithm is a viable alternative to the current, labor-intensive QC algorithm employed by TRMM GV.

Development of a prototype regeneration carbon dioxide absorber. [for use in EVA conditions

NASA Technical Reports Server (NTRS)

Patel, P. S.; Baker, B. S.

1977-01-01

A prototype regenerable carbon dioxide absorber was developed to maintain the environmental quality of the portable life support system. The absorber works on the alkali metal carbonate-bicarbonate solid-gas reaction to remove carbon dioxide from the atmosphere. The prototype sorber module was designed, fabricated, and tested at simulated extravehicular activity conditions to arrive at optimum design. The unit maintains sorber outlet concentration below 5 mm Hg. An optimization study was made with respect to heat transfer, temperature control, sorbent utilization, sorber life and regenerability, and final size of the module. Important parameters influencing the capacity of the final absorber unit were identified and recommendations for improvement were made.

76 FR 44809 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-27

...EPA is finalizing a limited approval and limited disapproval of permitting rules submitted for the Placer County Air Pollution Control District (PCAPCD) and Feather River Air Quality Management District (FRAQMD) portions of the California State Implementation Plan (SIP). These revisions were proposed in the Federal Register on May 19, 2011 and concern New Source Review (NSR) permit programs for new and modified major stationary sources of air pollution. We are approving local rules that regulate these emission sources under the Clean Air Act as amended in 1990 (CAA or the Act).

The test of VLSI circuits

NASA Astrophysics Data System (ADS)

Baviere, Ph.

Tests which have proven effective for evaluating VLSI circuits for space applications are described. It is recommended that circuits be examined after each manfacturing step to gain fast feedback on inadequacies in the production system. Data from failure modes which occur during operational lifetimes of circuits also permit redefinition of the manufacturing and quality control process to eliminate the defects identified. Other tests include determination of the operational envelope of the circuits, examination of the circuit response to controlled inputs, and the performance and functional speeds of ROM and RAM memories. Finally, it is desirable that all new circuits be designed with testing in mind.

Improved near real-time data management procedures for the Mediterranean ocean Forecasting System-Voluntary Observing Ship program

NASA Astrophysics Data System (ADS)

Manzella, G. M. R.; Scoccimarro, E.; Pinardi, N.; Tonani, M.

2003-01-01

A "ship of opportunity" program was launched as part of the Mediterranean Forecasting System Pilot Project. During the operational period (September 1999 to May 2000), six tracks covered the Mediterranean from the northern to southern boundaries approximately every 15 days, while a long eastwest track from Haifa to Gibraltar was covered approximately every month. XBT data were collected, sub-sampled at 15 inflection points and transmitted through a satellite communication system to a regional data centre. It was found that this data transmission system has limitations in terms of quality of the temperature profiles and quantity of data successfully transmitted. At the end of the MFSPP operational period, a new strategy for data transmission and management was developed. First of all, VOS-XBT data are transmitted with full resolution. Secondly, a new data management system, called Near Real Time Quality Control for XBT (NRT.QC.XBT), was defined to produce a parallel stream of high quality XBT data for further scientific analysis. The procedure includes: (1) Position control; (2) Elimination of spikes; (3) Re-sampling at a 1 metre vertical interval; (4) Filtering; (5) General malfunctioning check; (6) Comparison with climatology (and distance from this in terms of standard deviations); (7) Visual check; and (8) Data consistency check. The first six steps of the new procedure are completely automated; they are also performed using a new climatology developed as part of the project. The visual checks are finally done with a free-market software that allows NRT final data assessment.

A Compilation of Global Bio-Optical in Situ Data for Ocean-Colour Satellite Applications

NASA Technical Reports Server (NTRS)

Valente, Andre; Sathyendranath, Shubha; Brotus, Vanda; Groom, Steve; Grant, Michael; Taberner, Malcolm; Antoine, David; Arnone, Robert; Balch, William M.; Barker, Kathryn;

A multicentre non-blinded randomised controlled trial to assess the impact of regular early specialist symptom control treatment on quality of life in malignant mesothelioma (RESPECT-MESO): study protocol for a randomised controlled trial.

PubMed

Gunatilake, Samal; Brims, Fraser J H; Fogg, Carole; Lawrie, Iain; Maskell, Nick; Forbes, Karen; Rahman, Najib; Morris, Steve; Ogollah, Reuben; Gerry, Stephen; Peake, Mick; Darlison, Liz; Chauhan, Anoop J

2014-09-19

Malignant pleural mesothelioma is an incurable cancer caused by exposure to asbestos. The United Kingdom has the highest death rate from mesothelioma in the world and this figure is increasing. Median survival is 8 to 12 months, and most patients have symptoms at diagnosis. The fittest patients may be offered chemotherapy with palliative intent. For patients not fit for systemic anticancer treatment, best supportive care remains the mainstay of management. A study from the United States examining advanced lung cancer showed that early specialist palliative care input improved patient health related quality of life and depression symptoms 12 weeks after diagnosis. While mesothelioma and advanced lung cancer share many symptoms and have a poor prognosis, oncology and palliative care services in the United Kingdom, and many other countries, vary considerably compared to the United States. The aim of this trial is to assess whether regular early symptom control treatment provided by palliative care specialists can improve health related quality of life in patients newly diagnosed with mesothelioma. This multicentre study is an non-blinded, randomised controlled, parallel group trial. A total of 174 patients with a new diagnosis of malignant pleural mesothelioma will be minimised with a random element in a 1:1 ratio to receive either 4 weekly regular early specialist symptom control care, or standard care. The primary outcome is health related quality of life for patients at 12 weeks. Secondary outcomes include health related quality of life for patients at 24 weeks, carer health related quality of life at 12 and 24 weeks, patient and carer mood at 12 and 24 weeks, overall survival and analysis of healthcare utilisation and cost. Current practice in the United Kingdom is to involve specialist palliative care towards the final weeks or months of a life-limiting illness. This study aims to investigate whether early, regular specialist care input can result in significant health related quality of life gains for patients with mesothelioma and if this change in treatment model is cost-effective. The results will be widely applicable to many institutions and patients both in the United Kingdom and internationally. Current controlled trials ISRCTN18955704. Date ISRCTN assigned: 31 January 2014.

Surveillance of drug resistance for tuberculosis control: why and how?

PubMed

Chaulet, P; Boulahbal, F; Grosset, J

1995-12-01

The resistance of Mycobacterium tuberculosis to antibiotics, which reflects the quality of the chemotherapy applied in the community, is one of the elements of epidemiological surveillance used in national tuberculosis programmes. Measurement of drug resistance poses problems for biologists in standardization of laboratory methods and quality control. The definition of rates of acquired and primary drug resistance also necessitates standardization in the methods used to collect information transmitted by clinicians. Finally, the significance of the rates calculated depends on the choice of the patients sample on which sensitivity tests have been performed. National surveys of drug resistance therefore require multidisciplinary participation in order to select the only useful indicators: rates of primary resistance and of acquired resistance. These indicators, gathered in representative groups of patients over a long period, are a measurement of the impact of modern chemotherapy regimens on bacterial ecology.

The ASC/SIL ratio for cytopathologists as a quality control measure: a follow-up study.

PubMed

Nascimento, Alessandra F; Cibas, Edmund S

2007-10-01

Monitoring the relative frequency of the interpretations of atypical squamous cells (ASC) and squamous intraepithelial lesions (SIL) has been proposed as a quality control measure. To assess its value, an ASC/SIL ratio was calculated every 6 months for 3.5 years, and confidential feedback was provided to 10 cytopathologists (CPs). By using simple regression analysis, we analyzed the initial and final ASC/SIL ratios for individual CPs and for the entire group. The ratio was below the upper benchmark of 3:1 for all but 1 CP during every 6-month period. The ratio for all CPs combined showed a downward trend (from 2.05 to 1.73). The ratio for 6 CPs decreased, and for two of them the decrease was statistically significant. One CP showed a statistically significant increase in the ASC/SIL ratio. The decrease for some CPs likely reflects the salutary effect of confidential feedback and counseling.

Temperature Control and Numerical Analysis for Mass Concrete Pile Cap of Hai-huang Bridge

NASA Astrophysics Data System (ADS)

Shi, Han; Hao, Yang; Yong-liang, Wang

2018-05-01

In order to study the heat of hydration in massive concrete, this paper takes Hai-huang bridge for engineering background and uses the finite element analysis software of FEA to analyze the heat of hydration effect of the cushion cap. Comparing the measured data with the theory data, the results showed that the concrete crack was controlled effectively and ensure the construction quality by adopted reasonable temperature control measures. The results of the research prove that the measured data was consistent with calculation data, and it proves the accuracy of the finite element analysis. Finally, the study provides certain reference and guiding significance for similar project.

The association between higher body mass index and poor school performance in high school students.

PubMed

Tonetti, L; Fabbri, M; Filardi, M; Martoni, M; Natale, V

2016-12-01

This study aimed to examine the association between body mass index (BMI) and school performance in high school students by controlling for relevant mediators such as sleep quality, sleep duration and socioeconomic status. Thirty-seven high school students (mean age: 18.16 ± 0.44 years) attending the same school type, i.e. 'liceo scientifico' (science-based high school), were enrolled. Students' self-reported weight and height were used to calculate BMI. Participants wore an actigraph to objectively assess the quality and duration of sleep. School performance was assessed through the actual grade obtained at the final school-leaving exam, in which higher grades indicate higher performance. BMI, get-up time, mean motor activity, wake after sleep onset and number of awakenings were negatively correlated with the grade, while sleep efficiency was positively correlated. When performing a multiple regression analysis, BMI proved the only significant (negative) predictor of grade. When controlling for sleep quality, sleep duration and socioeconomic status, a higher BMI is associated with a poorer school performance in high school students. © 2015 World Obesity Federation.

Technology transfer through a network of standard methods and recommended practices - The case of petrochemicals

NASA Astrophysics Data System (ADS)

Batzias, Dimitris F.; Karvounis, Sotirios

2012-12-01

Technology transfer may take place in parallel with cooperative action between companies participating in the same organizational scheme or using one another as subcontractor (outsourcing). In this case, cooperation should be realized by means of Standard Methods and Recommended Practices (SRPs) to achieve (i) quality of intermediate/final products according to specifications and (ii) industrial process control as required to guarantee such quality with minimum deviation (corresponding to maximum reliability) from preset mean values of representative quality parameters. This work deals with the design of the network of SRPs needed in each case for successful cooperation, implying also the corresponding technology transfer, effectuated through a methodological framework developed in the form of an algorithmic procedure with 20 activity stages and 8 decision nodes. The functionality of this methodology is proved by presenting the path leading from (and relating) a standard test method for toluene, as petrochemical feedstock in the toluene diisocyanate production, to the (6 generations distance upstream) performance evaluation of industrial process control systems (ie., from ASTM D5606 to BS EN 61003-1:2004 in the SRPs network).

Influence of scanning parameters on the estimation accuracy of control points of B-spline surfaces

NASA Astrophysics Data System (ADS)

Aichinger, Julia; Schwieger, Volker

2018-04-01

This contribution deals with the influence of scanning parameters like scanning distance, incidence angle, surface quality and sampling width on the average estimated standard deviations of the position of control points from B-spline surfaces which are used to model surfaces from terrestrial laser scanning data. The influence of the scanning parameters is analyzed by the Monte Carlo based variance analysis. The samples were generated for non-correlated and correlated data, leading to the samples generated by Latin hypercube and replicated Latin hypercube sampling algorithms. Finally, the investigations show that the most influential scanning parameter is the distance from the laser scanner to the object. The angle of incidence shows a significant effect for distances of 50 m and longer, while the surface quality contributes only negligible effects. The sampling width has no influence. Optimal scanning parameters can be found in the smallest possible object distance at an angle of incidence close to 0° in the highest surface quality. The consideration of correlations improves the estimation accuracy and underlines the importance of complete stochastic models for TLS measurements.

Infection control in home-based care for people living with HIV/AIDS/TB in South Africa: an exploratory study.

PubMed

Akintola, Olagoke; Hangulu, Lydia

2014-01-01

The majority of HIV and AIDS patients in sub-Saharan African countries receive health care services at home. Yet research on infection control in home-based care settings is virtually non-existent. This study explored infection control practices in home-based care in a South African province with a high HIV/TB prevalence. We conducted interviews with 10 managers of home-based care organizations and 10 focus group discussions with 80 volunteer caregivers working in high HIV/TB prevalent communities in South Africa. Findings show that volunteers had insufficient training on infection control. Materials necessary for the maintenance of hygiene and protective equipment were in short supply and the protective equipment supplied was of poor quality. Home-based care patients lived in crowded and poor conditions, and family members were negatively disposed to the use of protective devices. Together, these factors put volunteers and family caregivers at risk of infection with HIV and TB. Health policy should address the training of volunteer caregivers and the regular supply of good quality materials to ensure effective infection control. It is also important to educate families on infection control. Finally, there is a need to integrate HIV and TB control at the community level.

Implementation of statistical process control for proteomic experiments via LC MS/MS.

PubMed

Bereman, Michael S; Johnson, Richard; Bollinger, James; Boss, Yuval; Shulman, Nick; MacLean, Brendan; Hoofnagle, Andrew N; MacCoss, Michael J

2014-04-01

Statistical process control (SPC) is a robust set of tools that aids in the visualization, detection, and identification of assignable causes of variation in any process that creates products, services, or information. A tool has been developed termed Statistical Process Control in Proteomics (SProCoP) which implements aspects of SPC (e.g., control charts and Pareto analysis) into the Skyline proteomics software. It monitors five quality control metrics in a shotgun or targeted proteomic workflow. None of these metrics require peptide identification. The source code, written in the R statistical language, runs directly from the Skyline interface, which supports the use of raw data files from several of the mass spectrometry vendors. It provides real time evaluation of the chromatographic performance (e.g., retention time reproducibility, peak asymmetry, and resolution), and mass spectrometric performance (targeted peptide ion intensity and mass measurement accuracy for high resolving power instruments) via control charts. Thresholds are experiment- and instrument-specific and are determined empirically from user-defined quality control standards that enable the separation of random noise and systematic error. Finally, Pareto analysis provides a summary of performance metrics and guides the user to metrics with high variance. The utility of these charts to evaluate proteomic experiments is illustrated in two case studies.

EPA Finalizes Voluntary Quality Assurance Plan for Renewable Fuel Standard Program

EPA Pesticide Factsheets

The rule finalizes a voluntary third-party quality assurance program option for RINs that regulated parties may exercise as a supplement to the “buyer beware” liability as prescribed under existing regulations.

Quality of full and final publications reporting acute stroke trials: a systematic review.

PubMed

Bath, F J; Owen, V E; Bath, P M

1998-10-01

Several studies have shown that the quality of reporting of trials throughout medicine is variable and often poor. We report on the quality of the final reports of randomized controlled trials (RCTs) of drug therapies assessed in acute stroke. English-language reports published up to the end of 1996 relating to completed RCTs in acute stroke were identified from electronic searches of the Cochrane Stroke Review Group database of stroke trials and the Cochrane Controlled Trials Register (CD-ROM issue 1, 1997, of the Cochrane Library). Report quality was assessed with the 33 criteria of the CONSORT statement and 53 additional factors relevant to acute stroke or trials in general. Trial quality was also assessed with a 7-point scale. Up to 1996, 114 RCTs were published which involved 20 536 patients (median, 80; range, 16 to 1267 per trial); 39 (35.5%) of these were published in Stroke. The median total report quality was 40/86 (range, 15 to 61) for all criteria and 19/33 (range, 9 to 29) for the CONSORT criteria alone. Although adequate information was given in the introduction and discussion sections of most reports, insufficient details were given on methods, assignment of patients to treatment groups, statistical analyses, the prevalence of risk factors, and assessment of outcomes. Report quality has improved between 1956 and 1996 (Spearman correlation coefficient [rs], 0.575; 95% confidence interval [CI], 0. 439 to 0.685) and was superior in large trials (rs=0.434; 95% CI, 0. 274 to 0.571). Although report quality was related to trial quality (rs=0.675; 95% CI, 0.563 to 0.763), it was not related to journal impact factor (rs=0.170; 95% CI, -0.015 to 0.344). Trials with a positive outcome tended to be less well reported than those with a neutral or negative outcome (rs=-0.192; 95% CI, -0.351 to -0.011). The overall quality of study reports for parallel group RCTs in acute stroke is poor but appears to be improving with time and in parallel with an increase in trial size. Reports often lack detailed information on the methods of randomization, concealment of allocation, and statistical analysis, all factors which can, if undertaken poorly, affect trial results and validity. It is vital that future trials are adequately reported; we believe that authors should follow the CONSORT guidelines and that referees and editors should ensure this happens.

Magnetic Field Applications in Semiconductor Crystal Growth and Metallurgy

NASA Technical Reports Server (NTRS)

Mazuruk, Konstantin; Ramachandran, Narayanan; Grugel, Richard; Curreri, Peter A. (Technical Monitor)

2002-01-01

The Traveling Magnetic Field (TMF) technique, recently proposed to control meridional flow in electrically conducting melts, is reviewed. In particular, the natural convection damping capability of this technique has been numerically demonstrated with the implication of significantly improving crystal quality. Advantages of the traveling magnetic field, in comparison to the more mature rotating magnetic field method, are discussed. Finally, results of experiments with mixing metallic alloys in long ampoules using TMF is presented

Development of Medical Technology for Contingency Response to Marrow Toxic Agents

DTIC Science & Technology

2014-05-06

Development of Medical Technology for Contingency Response to Marrow Toxic Agents - Final Performance/Technical Report for January 01, 2011 to...Enhancing HLA Data for Selected Donors 44 IIB.1.6 Maintain a Quality Control Program 44 IIB.2.1 Collection of Primary Data 45 IIB.2.2 Validation of...Receptor Donor Selection KORI Korean LD Linkage Disequilibrium LTA Lymphotoxin Alpha MALDI-TOF Matrix-Assisted Laser Desorption/Ionization – Time Of

High-Fidelity Geometric Modeling and Mesh Generation for Mechanics Characterization of Polycrystalline Materials

DTIC Science & Technology

2015-01-07

and anisotropic quadrilateral meshes, which can be used as the control mesh for high-order T- spline surface modeling. Archival publications (published...anisotropic T-meshes for the further T- spline surface construction. Finally, a gradient flow-based method is developed to improve the T-mesh quality...shade-off. Halos are bright or dark thin regions around the boundary of the sample. These false edges around the object make many segmentation

75 FR 75455 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Full...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-03

...-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Full Sunset Review of Countervailing... of the countervailing duty (CVD) order on certain hot-rolled flat-rolled carbon-quality steel products (hot-rolled steel) from Brazil, pursuant to section 751(c) of the Tariff Act of 1930, as amended...

76 FR 66927 - New York State Prohibition of Discharges of Vessel Sewage; Final Affirmative Determination

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-28

.... 1322(f)(3)), the State of New York has determined that the protection and enhancement of the quality of... certified the need for greater protection of the water quality. EPA hereby makes a final affirmative... commenters pointed out that this action will reduce pathogens and chemicals, improve water quality and...

The effect of land use change on water quality: A case study in Ciliwung Watershed

NASA Astrophysics Data System (ADS)

Ayu Permatasari, Prita; Setiawan, Yudi; Nur Khairiah, Rahmi; Effendi, Hefni

2017-01-01

Ciliwung is the biggest river in Jakarta. It is 119 km long with a catchment area of 476 km2. It flows from Bogor Regency and crosses Bogor City, Depok City, and Jakarta before finally flowing into Java Sea through Jakarta Bay. The water quality in Ciliwung River has degraded. Many factors affect water quality. Understanding the relationship between land use and surface water quality is necessary for effective water management. It has been widely accepted that there is a close relationship between the land use type and water quality. This study aims to analyze the influence of various land use types on the water quality within the Ciliwung Watershed based on the water quality monitoring data and remote sensing data in 2010 and 2014. Water quality parameters exhibited significant variations between the urban-dominated and forest-dominated sites. The proportion of urban land was strongly positively associated with total nitrogen and ammonia nitrogen concentrations. The result can provide scientific reference for the local land use optimization and water pollution control and guidance for the formulation of policies to coordinate the exploitation and protection of the water resource.

Do Energy Efficiency Standards Improve Quality? Evidence from a Revealed Preference Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Houde, Sebastien; Spurlock, C. Anna

Minimum energy efficiency standards have occupied a central role in U.S. energy policy for more than three decades, but little is known about their welfare effects. In this paper, we employ a revealed preference approach to quantify the impact of past revisions in energy efficiency standards on product quality. The micro-foundation of our approach is a discrete choice model that allows us to compute a price-adjusted index of vertical quality. Focusing on the appliance market, we show that several standard revisions during the period 2001-2011 have led to an increase in quality. We also show that these standards have hadmore » a modest effect on prices, and in some cases they even led to decreases in prices. For revision events where overall quality increases and prices decrease, the consumer welfare effect of tightening the standards is unambiguously positive. Finally, we show that after controlling for the effect of improvement in energy efficiency, standards have induced an expansion of quality in the non-energy dimension. We discuss how imperfect competition can rationalize these results.« less

Passion for an activity and quality of interpersonal relationships: the mediating role of emotions.

PubMed

Philippe, Frederick L; Vallerand, Robert J; Houlfort, Nathalie; Lavigne, Geneviève L; Donahue, Eric G

2010-06-01

Our purpose in this research was to investigate the role of passion (Vallerand et al., 2003) for a given activity in the quality of interpersonal relationships experienced within the context of that activity in 4 studies. Study 1 demonstrated that a harmonious passion was positively associated with the quality of interpersonal relationships within the context of the passionate activity, whereas an obsessive passion was unrelated to it. Furthermore, in line with the broaden-and-build theory (Fredrickson, 2001), results also showed that positive emotions experienced at work fully mediated the relation between harmonious passion and quality of interpersonal relationships. Obsessive passion was not associated with positive emotions. Study 2 replicated the results from Study 1 while controlling for trait extraversion. Also, in Study 2, we examined the negative mediating role of negative emotions between obsessive passion and quality of interpersonal relationships. Finally, Studies 3 and 4 replicated the results of Study 2 with prospective designs and with objective ratings of interpersonal relationships quality. Implications for the dualistic model of passion and the broaden-and-build theory are discussed. (c) 2010 APA, all rights reserved).

Fault-Tolerant Control of ANPC Three-Level Inverter Based on Order-Reduction Optimal Control Strategy under Multi-Device Open-Circuit Fault.

PubMed

Xu, Shi-Zhou; Wang, Chun-Jie; Lin, Fang-Li; Li, Shi-Xiang

2017-10-31

The multi-device open-circuit fault is a common fault of ANPC (Active Neutral-Point Clamped) three-level inverter and effect the operation stability of the whole system. To improve the operation stability, this paper summarized the main solutions currently firstly and analyzed all the possible states of multi-device open-circuit fault. Secondly, an order-reduction optimal control strategy was proposed under multi-device open-circuit fault to realize fault-tolerant control based on the topology and control requirement of ANPC three-level inverter and operation stability. This control strategy can solve the faults with different operation states, and can works in order-reduction state under specific open-circuit faults with specific combined devices, which sacrifices the control quality to obtain the stability priority control. Finally, the simulation and experiment proved the effectiveness of the proposed strategy.

Precision Viticulture : is it relevant to manage the vineyard according to the within field spatial variability of the environment ?

NASA Astrophysics Data System (ADS)

Tisseyre, Bruno

2015-04-01

For more than 15 years, research projects are conducted in the precision viticulture (PV) area around the world. These research projects have provided new insights into the within-field variability in viticulture. Indeed, access to high spatial resolution data (remote sensing, embedded sensors, etc.) changes the knowledge we have of the fields in viticulture. In particular, the field which was until now considered as a homogeneous management unit, presents actually a high spatial variability in terms of yield, vigour an quality. This knowledge will lead (and is already causing) changes on how to manage the vineyard and the quality of the harvest at the within field scale. From the experimental results obtained in various countries of the world, the goal of the presentation is to provide figures on: - the spatial variability of the main parameters (yield, vigor, quality), and how this variability is organized spatially, - the temporal stability of the observed spatial variability and the potential link with environmental parameters like soil, topography, soil water availability, etc. - information sources available at a high spatial resolution conventionally used in precision agriculture likely to highlight this spatial variability (multi-spectral images, soil electrical conductivity, etc.) and the limitations that these information sources are likely to present in viticulture. Several strategies are currently being developed to take into account the within field variability in viticulture. They are based on the development of specific equipments, sensors, actuators and site specific strategies with the aim of adapting the vineyard operations at the within-field level. These strategies will be presented briefly in two ways : - Site specific operations (fertilization, pruning, thinning, irrigation, etc.) in order to counteract the effects of the environment and to obtain a final product with a controlled and consistent wine quality, - Differential harvesting with the objective to take advantage of the observed spatial variability to produce different quality of wines. These later approach tends to produce very different quality wines which will be blended to control the final quality and/or marketed differently. These applications show that the environment and its spatial variability can be valued with the goal of controlling the final quality of the wine produced. Technologies to characterize the spatial variability of vine fields are currently in rapid evolution. They will significantly impact production methods and management strategies of the vineyard. In its last part, the presentation will summarize the technologies likely to impact the knowledge and the vineyard management either at the field level, at the vineyard level or at the regional level. A brief overview of the needs in terms of information processing will be also performed. A reflection on the difficulties that might limit the adoption of precision viticulture technologies (PV) will be done. Indeed, although very informative, PV entails high costs of information acquisition and data processing. Cost is one of the major obstacles to the dissemination of these tools and services to the majority of wine producers. In this context, the pooling of investments is a choke point to make the VP accessible to the highest number of growers. Thus, to be adopted, the VP will necessarily satisfy the operational requirements at the field level, but also throughout the whole production area (at the regional level). This working scale raises new scientific questions to be addressed.

Sustainable Improvement of Urban River Network Water Quality and Flood Control Capacity by a Hydrodynamic Control Approach-Case Study of Changshu City

NASA Astrophysics Data System (ADS)

Xie, Chen; Yang, Fan; Liu, Guoqing; Liu, Yang; Wang, Long; Fan, Ziwu

2017-01-01

Water environment of urban rivers suffers degradation with the impacts of urban expansion, especially in Yangtze River Delta. The water area in cites decreased sharply, and some rivers were cut off because of estate development, which brings the problems of urban flooding, flow stagnation and water deterioration. The approach aims to enhance flood control capability and improve the urban river water quality by planning gate-pump stations surrounding the cities and optimizing the locations and functions of the pumps, sluice gates, weirs in the urban river network. These gate-pump stations together with the sluice gates and weirs guarantee the ability to control the water level in the rivers and creating hydraulic gradient artificially according to mathematical model. Therefore the flow velocity increases, which increases the rate of water exchange, the DO concentration and water body self-purification ability. By site survey and prototype measurement, the river problems are evaluated and basic data are collected. The hydrodynamic model of the river network is established and calibrated to simulate the scenarios. The schemes of water quality improvement, including optimizing layout of the water distribution projects, improvement of the flow discharge in the river network and planning the drainage capacity are decided by comprehensive Analysis. Finally the paper introduces the case study of the approach in Changshu City, where the approach is successfully implemented.

Quality control for quantitative PCR based on amplification compatibility test.

PubMed

Tichopad, Ales; Bar, Tzachi; Pecen, Ladislav; Kitchen, Robert R; Kubista, Mikael; Pfaffl, Michael W

2010-04-01

Quantitative qPCR is a routinely used method for the accurate quantification of nucleic acids. Yet it may generate erroneous results if the amplification process is obscured by inhibition or generation of aberrant side-products such as primer dimers. Several methods have been established to control for pre-processing performance that rely on the introduction of a co-amplified reference sequence, however there is currently no method to allow for reliable control of the amplification process without directly modifying the sample mix. Herein we present a statistical approach based on multivariate analysis of the amplification response data generated in real-time. The amplification trajectory in its most resolved and dynamic phase is fitted with a suitable model. Two parameters of this model, related to amplification efficiency, are then used for calculation of the Z-score statistics. Each studied sample is compared to a predefined reference set of reactions, typically calibration reactions. A probabilistic decision for each individual Z-score is then used to identify the majority of inhibited reactions in our experiments. We compare this approach to univariate methods using only the sample specific amplification efficiency as reporter of the compatibility. We demonstrate improved identification performance using the multivariate approach compared to the univariate approach. Finally we stress that the performance of the amplification compatibility test as a quality control procedure depends on the quality of the reference set. Copyright 2010 Elsevier Inc. All rights reserved.

Quality specification and status of internal quality control of cardiac biomarkers in China from 2011 to 2016.

PubMed

Li, Tingting; Wang, Wei; Zhao, Haijian; He, Falin; Zhong, Kun; Yuan, Shuai; Wang, Zhiguo

2017-09-07

This study aimed to investigate the status of internal quality control (IQC) for cardiac biomarkers from 2011 to 2016 so that we can have overall knowledge of the precision level of measurements in China and set appropriate precision specifications. Internal quality control data of cardiac biomarkers, including creatinine kinase MB (CK-MB) (μg/L), CK-MB(U/L), myoglobin (Mb), cardiac troponin I (cTnI), cardiac troponin T (cTnT), and homocysteines (HCY), were collected by a web-based external quality assessment (EQA) system. Percentages of laboratories meeting five precision quality specifications for current coefficient of variations (CVs) were calculated. Then, appropriate precision specifications were chosen for these six analytes. Finally, the CVs and IQC practice were further analyzed with different grouping methods. The current CVs remained nearly constant for 6 years. cTnT had the highest pass rates every year against five specifications, whereas HCY had the lowest pass rates. Overall, most analytes had a satisfactory performance (pass rates >80%), except for HCY, if one-third TEa or the minimum specification were employed. When the optimal specification was applied, the performance of most analytes was frustrating (pass rates < 60%) except for cTnT. The appropriate precision specifications of Mb, cTnI, cTnT and HCY were set as current CVs less than 9.20%, 9.90%, 7.50%, 10.54%, 7.63%, and 6.67%, respectively. The data of IQC practices indicated wide variation and substantial progress. The precision performance of cTnT was already satisfying, while the other five analytes, especially HCY, were still frustrating; thus, ongoing investigation and continuous improvement for IQC are still needed. © 2017 Wiley Periodicals, Inc.

[Quality control of oral anticoagulant therapy in Primary Care in Madrid City, Spain: CHRONOS-TAO study].

PubMed

Alonso Roca, Rafael; Figueroa Guerrero, Carmen Arlene; Mainar de Paz, Victoria; Arribas García, M Paz; Sánchez Perruca, Luis; Rodríguez Barrientos, Ricardo; Casado López, Mariano; Pedraza Flechas, Ana M

2015-09-07

To determine quality control of patients with oral anticoagulant treatment recruited in Primary Care (PC) using the Rosendaal method to estimate time in therapeutic range (TTR) and comparing it with fraction of international normalized ratio (INR) in range and cross-sectional analysis (last INR registred). A retrospective observational study based on electronic medical record in routine clinical practice. PC centers (262) in Madrid. We included all patients with acenocumarol treatment, with an INR therapeutic range established between 2 and 3. We excluded patients with valvular pathology and disrupted clinical follow up in PC (<3 INR determinations in the studied period, a period of>90 days or ≥ 3 periods of>60 days between 2 determinations). The final population was 49,312 patients. The variables considered were all INR values and their respective dates. TTR was calculated by the 3 methods above mentioned. We considered "therapeutic range" INR between 2-3 and "adjusted range" INR between 1.8-3.2. Optimal control for each patient was considered TTR>60%. By using Rosendaal method, TTR was 66.8% (81.7% adjusted), with a percentage of total INR in range was 58.8% (66.5% adjusted), and, with the cross-sectional analysis, it was 70.5% (76.8% adjusted). Mean TTR was 65% (standard deviation 20.3), and the percentage of patients with TTR>60% was 63.3% (88.1% adjusted). The quality control of patients with oral anticoagulants in PC in Madrid is acceptable, similar or higher to other studies and pivotal trials of new anticoagulants. Compared to the Rosendaal method, total fraction of INR underestimates quality control, and cross-sectional analysis slightly overestimates it. Copyright © 2014 Elsevier España, S.L.U. All rights reserved.

The economic effect of Planet Health on preventing bulimia nervosa.

PubMed

Wang, Li Yan; Nichols, Lauren P; Austin, S Bryn

2011-08-01

To assess the economic effect of the school-based obesity prevention program Planet Health on preventing disordered weight control behaviors and to determine the cost-effectiveness of the intervention in terms of its combined effect on prevention of obesity and disordered weight control behaviors. On the basis of the intervention's short-term effect on disordered weight control behaviors prevention, we projected the number of girls who were prevented from developing bulimia nervosa by age 17 years. We further estimated medical costs saved and quality-adjusted life years gained by the intervention over 10 years. As a final step, we compared the intervention costs with the combined intervention benefits from both obesity prevention (reported previously) and prevention of disordered weight control behaviors to determine the overall cost-effectiveness of the intervention. Middle schools. A sample of 254 intervention girls aged 10 to 14 years. The Planet Health program was implemented during the school years from 1995 to 1997 and was designed to promote healthful nutrition and physical activity among youth. Intervention costs, medical costs saved, quality-adjusted life years gained, and cost-effectiveness ratio. An estimated 1 case of bulimia nervosa would have been prevented. As a result, an estimated $33 999 in medical costs and 0.7 quality-adjusted life years would be saved. At an intervention cost of $46 803, the combined prevention of obesity and disordered weight control behaviors would yield a net savings of $14 238 and a gain of 4.8 quality-adjusted life years. Primary prevention programs, such as Planet Health, warrant careful consideration by policy makers and program planners. The findings of this study provide additional argument for integrated prevention of obesity and eating disorders.

Prevention and control of food safety risks: the role of governments, food producers, marketers, and academia.

PubMed

Lupien, John R

2007-01-01

Food systems are rapidly changing as world population grows, increasing urbanization occurs, consumer tastes and preferences change and differ in various countries and cultures, large scale food production increases, and food imports and exports grow in volume and value. Consumers in all countries have become more insistent that foods available in the marketplace are of good quality and safe, and do not pose risks to them and their families. Publicity about food risk problems and related risks, including chemical and microbiological contamination of foods, mad-cow disease, avian flu, industrial chemical contamination all have made consumers and policy makers more aware of the need of the control of food safety risk factors in all countries. To discuss changes in food systems, and in consumer expectations, that have placed additional stress on the need for better control of food safety risks. Food producers, processors, and marketers have additional food law and regulations to meet; government agencies must increase monitoring and enforcement of adequate food quality and safety legislation and coordinate efforts between agriculture, health, trade, justice and customs agencies; and academia must take action to strengthen the education of competent food legislation administrators, inspectorate, and laboratory personnel for work in government and industry, including related food and food safety research . Both Government and the food industry must assure that adequate control programs are in place to control the quality and safety of all foods, raw or processed, throughout the food chain from production to final consumption. This includes appropriate laboratory facilities to perform necessary analysis of foods for risk and quality factors, and to carry out a wide range of food science, toxicological and related research.

Integrating anthropogenic hazard data to facilitate research related to the exploitation of geo-resources

NASA Astrophysics Data System (ADS)

Kwiatek, Grzegorz; Blanke, Aglaja; Olszewska, Dorota; Orlecka-Sikora, Beata; Lasocki, Stanisław; Kozlovskaya, Elena; Nevalainen, Jouni; Schmittbuhl, Jean; Grasso, Jean-Robert; Schaming, Marc; Bigarre, Pascal; Kinscher, Jannes-Lennart; Saccorotti, Gilberto; Garcia, Alexander; Cassidy, Nigel; Toon, Sam; Mutke, Grzegorz; Sterzel, Mariusz; Szepieniec, Tomasz

2017-04-01

The Thematic Core Service "Anthropogenic Hazards" (TCS AH) integrates data and provides various data services in a form of complete e-research infrastructure for advanced analysis and geophysical modelling of anthropogenic hazard due to georesources exploitation. TCS AH is based on the prototype built in the framework of the IS-EPOS project POIG.02.03.00-14-090/13-00 (https://tcs.ah-epos.eu/). The TCS AH is currently being further developed within EPOS Implementation phase (H2020-INFRADEV-1-2015-1, INFRADEV-3-2015). The TCS AH aims to have a measurable impact on innovative research and development by providing a comprehensive, wide-scale and high quality research infrastructure available to the scientific community, industrial partners and public. One of the main deliverable of TCS AH is the access to numerous induced seismicity datasets called "episodes". The episode is defined as a comprehensive set of data describing the geophysical process induced or triggered by technological activity, which under certain circumstances can become hazardous for people, infrastructure and the environment. The episode is a time-correlated, standardized collection of geophysical, technological and other relevant geodata forming complete documentation of seismogenic process. In addition to the 6 episodes already implemented during previous phase of integration, and 3 episodes integrated within SHEER project, at least 18 new episodes related to conventional hydrocarbon extraction, reservoir treatment, underground mining and geothermal energy production are currently being integrated into the TCS AH. The heterogeneous multi-disciplinary data from different episodes are subjected to an extensive quality control (QC) procedure composed of five steps and involving the collaborative work of data providers, quality control team, IT team, that is being supervised by the quality control manager with the aid of Redmine platform. The first three steps of QC are performed at local data center and include the (1) transfer of episode data to the local data center, (2) data standardization and validation of formats, (3) metadata preparation according to TCS AH metadata scheme. The final two steps of QC are performed already at the level of TCS AH website and include (4) Contextual analysis of data quality followed by appearance of episode in TCS AH maintenance area, and finally the (5) Episode publication at TCS AH website.

Psychosocial Characteristics of Children with Central Disorders of Hypersomnolence Versus Matched Healthy Children.

PubMed

Avis, Kristin T; Shen, Jiabin; Weaver, Patrick; Schwebel, David C

2015-11-15

Hypersomnia of central origin from narcolepsy or idiopathic hypersomnia (IHS) is characterized by pathological levels of excessive daytime sleepiness (EDS). Central hypersomnia has historically been underdiagnosed and poorly understood, especially with respect to its impact on daytime functioning and quality of life in children. Describe the psychosocial adjustment of children treated for narcolepsy or IHS on school performance, quality of life, and physical/extracurricular activities. Using a matched case control design, we compared child self- and parent-reported data from thirty-three 8- to 16-year-olds with an established diagnosis of narcolepsy or IHS, according to ICSD-2 criteria, to that of 33 healthy children matched by age, race/ethnicity, gender, and household income. Assessments evaluated academic performance, quality of life and wellness, sleepiness, and participation in extracurricular activities. Compared to healthy controls, children with central hypersomnia had poorer daytime functioning in multiple domains. Children with hypersomnia missed more days of school and had lower grades than healthy controls. Children with hypersomnia had poorer quality of life by both parent and child report. Children with hypersomnia were significantly sleepier, had higher BMI, and were more likely to report a history of recent injury. Finally, children with hypersomnia engaged in fewer after-school activities than healthy controls. A range of significant psychosocial consequences are reported in children with hypersomnia even after a diagnosis has been made and treatments initiated. Health care professionals should be mindful of the psychosocial problems that may present in children with hypersomnia over the course of treatment. © 2015 American Academy of Sleep Medicine.

Building large mosaics of confocal edomicroscopic images using visual servoing.

PubMed

Rosa, Benoît; Erden, Mustafa Suphi; Vercauteren, Tom; Herman, Benoît; Szewczyk, Jérôme; Morel, Guillaume

2013-04-01

Probe-based confocal laser endomicroscopy provides real-time microscopic images of tissues contacted by a small probe that can be inserted in vivo through a minimally invasive access. Mosaicking consists in sweeping the probe in contact with a tissue to be imaged while collecting the video stream, and process the images to assemble them in a large mosaic. While most of the literature in this field has focused on image processing, little attention has been paid so far to the way the probe motion can be controlled. This is a crucial issue since the precision of the probe trajectory control drastically influences the quality of the final mosaic. Robotically controlled motion has the potential of providing enough precision to perform mosaicking. In this paper, we emphasize the difficulties of implementing such an approach. First, probe-tissue contacts generate deformations that prevent from properly controlling the image trajectory. Second, in the context of minimally invasive procedures targeted by our research, robotic devices are likely to exhibit limited quality of the distal probe motion control at the microscopic scale. To cope with these problems visual servoing from real-time endomicroscopic images is proposed in this paper. It is implemented on two different devices (a high-accuracy industrial robot and a prototype minimally invasive device). Experiments on different kinds of environments (printed paper and ex vivo tissues) show that the quality of the visually servoed probe motion is sufficient to build mosaics with minimal distortion in spite of disturbances.

Final-impression techniques and materials for making complete and removable partial dentures.

PubMed

Jayaraman, Srinivasan; Singh, Balendra P; Ramanathan, Balasubramanian; Pazhaniappan Pillai, Murukan; MacDonald, Laura; Kirubakaran, Richard

2018-04-04

Edentulism is relatively common and is often treated with the provision of complete or partial removable dentures. Clinicians make final impressions of complete dentures (CD) and removable partial dentures (RPD) using different techniques and materials. Applying the correct impression technique and material, based on an individual's oral condition, improves the quality of the prosthesis, which may improve quality of life. To assess the effects of different final-impression techniques and materials used to make complete dentures, for retention, stability, comfort, and quality of life in completely edentulous people.To assess the effects of different final-impression techniques and materials used to make removable partial dentures, for stability, comfort, overextension, and quality of life in partially edentulous people. Cochrane Oral Health's Information Specialist searched the following databases: Cochrane Oral Health's Trials Register (to 22 November 2017), the Cochrane Central Register of Controlled Trials (CENTRAL) (Cochrane Register of Studies, to 22 November 2017), MEDLINE Ovid (1946 to 22 November 2017), and Embase Ovid (21 December 2015 to 22 November 2017). The US National Institutes of Health Trials Registry (ClinicalTrials.gov) and the World Health Organization International Clinical Trials Registry Platform were searched for ongoing trials. No restrictions were placed on language or publication status when searching the electronic databases, however the search of Embase was restricted by date due to the Cochrane Centralised Search Project to identify all clinical trials and add them to CENTRAL. We included randomised controlled trials (RCTs) comparing different final-impression techniques and materials for treating people with complete dentures (CD) and removable partial dentures (RPD). For CD, we included trials that compared different materials or different techniques or both. In RPD for tooth-supported conditions, we included trials comparing the same material and different techniques, or different materials and the same technique. In tooth- and tissue-supported RPD, we included trials comparing the same material and different dual-impression techniques, and different materials with different dual-impression techniques. Two review authors independently, and in duplicate, screened studies for eligibility, extracted data, and assessed the risk of bias for each included trial. We expressed results as risk ratios (RR) for dichotomous outcomes, and as mean differences (MD) or standardised mean differences (SMD) for continuous outcomes, with 95% confidence intervals (CI), using the random-effects model. We constructed 'Summary of findings' tables for the main comparisons and outcomes (participant-reported oral health-related quality of life, quality of the denture, and denture border adjustments). We included nine studies in this review. Eight studies involved 485 participants with CD. We assessed six of the studies to be at high risk of bias, and two to be at low risk of bias. We judged one study on RPD with 72 randomised participants to be at high risk of bias.Overall, the quality of the evidence for each comparison and outcome was either low or very low, therefore, results should be interpreted with caution, as future research is likely to change the findings.Complete denturesTwo studies compared the same material and different techniques (one study contributed data to a secondary outcome only); two studies compared the same technique and different materials; and four studies compared different materials and techniques.One study (10 participants) evaluated two stage-two step, Biofunctional Prosthetic system (BPS) using additional silicone elastomer compared to conventional methods, and found no evidence of a clear difference for oral health-related quality of life, or quality of the dentures (denture satisfaction). The study reported that BPS required fewer adjustments. We assessed the quality of the evidence as very low.One study (27 participants) compared selective pressure final-impression technique using wax versus polysulfide elastomeric (rubber) material. The study did not measure quality of life or dentures, and found no evidence of a clear difference between interventions in the need for adjustments (RR 0.81, 95% CI 0.38 to 1.70). We assessed the quality of the evidence as very low.One study compared two stage-two step final impression with alginate versus silicone elastomer. Oral health-related quality of life measured by the OHIP-EDENT seemed to be better with silicone (MD 7.20, 95% CI 2.71 to 11.69; 144 participants). The study found no clear differences in participant-reported quality of the denture (comfort) after a two-week 'confirmation' period, but reported that silicone was better for stability and chewing efficiency. We assessed the quality of the evidence as low.Three studies compared single-stage impressions with alginate versus two stage-two step with elastomer (silicone, polysulfide, or polyether) impressions. There was no evidence of a clear difference in the OHIP-EDENT at one month (MD 0.05, 95% CI -2.37 to 2.47; two studies, 98 participants). There was no evidence of a clear difference in participant-rated general satisfaction with dentures at six months (MD 0.00, 95% CI -8.23 to 8.23; one study, 105 participants). We assessed the quality of the evidence as very low.One study compared single-stage alginate versus two stage-two step using zinc-oxide eugenol, and found no evidence of a clear difference in OHIP-EDENT (MD 0.50, 95% CI -2.67 to 3.67; 39 participants), or general satisfaction (RR 3.15, 95% CI 0.14 to 72.88; 39 participants) at six months. We assessed the quality of the evidence as very low.Removable partial denturesOne study randomised 72 participants and compared altered-cast technique versus one-piece cast technique. The study did not measure quality of life, but reported that most participants were satisfied with the dentures and there was no evidence of any clear difference between groups for general satisfaction at one-year follow-up (low-quality evidence). There was no evidence of a clear difference in number of intaglio adjustments at one year (RR 1.43, 95% CI 0.61 to 3.34) (very low-quality evidence). We conclude that there is no clear evidence that one technique or material has a substantial advantage over another for making complete dentures and removable partial dentures. Available evidence for the relative benefits of different denture fabrication techniques and final-impression materials is limited and is of low or very low quality. More high-quality RCTs are required.

Quality Controlled Radiosonde Profile from MC3E

DOE Data Explorer

Toto, Tami; Jensen, Michael

2014-11-13

The sonde-adjust VAP produces data that corrects documented biases in radiosonde humidity measurements. Unique fields contained within this datastream include smoothed original relative humidity, dry bias corrected relative humidity, and final corrected relative humidity. The smoothed RH field refines the relative humidity from integers - the resolution of the instrument - to fractions of a percent. This profile is then used to calculate the dry bias corrected field. The final correction fixes a time-lag problem and uses the dry-bias field as input into the algorithm. In addition to dry bias, solar heating is another correction that is encompassed in the final corrected relative humidity field. Additional corrections were made to soundings at the extended facility sites (S0*) as necessary: Corrected erroneous surface elevation (and up through rest of height of sounding), for S03, S04 and S05. Corrected erroneous surface pressure at Chanute (S02).

Implementation of Cyber-Physical Production Systems for Quality Prediction and Operation Control in Metal Casting.

PubMed

Lee, JuneHyuck; Noh, Sang Do; Kim, Hyun-Jung; Kang, Yong-Shin

2018-05-04

The prediction of internal defects of metal casting immediately after the casting process saves unnecessary time and money by reducing the amount of inputs into the next stage, such as the machining process, and enables flexible scheduling. Cyber-physical production systems (CPPS) perfectly fulfill the aforementioned requirements. This study deals with the implementation of CPPS in a real factory to predict the quality of metal casting and operation control. First, a CPPS architecture framework for quality prediction and operation control in metal-casting production was designed. The framework describes collaboration among internet of things (IoT), artificial intelligence, simulations, manufacturing execution systems, and advanced planning and scheduling systems. Subsequently, the implementation of the CPPS in actual plants is described. Temperature is a major factor that affects casting quality, and thus, temperature sensors and IoT communication devices were attached to casting machines. The well-known NoSQL database, HBase and the high-speed processing/analysis tool, Spark, are used for IoT repository and data pre-processing, respectively. Many machine learning algorithms such as decision tree, random forest, artificial neural network, and support vector machine were used for quality prediction and compared with R software. Finally, the operation of the entire system is demonstrated through a CPPS dashboard. In an era in which most CPPS-related studies are conducted on high-level abstract models, this study describes more specific architectural frameworks, use cases, usable software, and analytical methodologies. In addition, this study verifies the usefulness of CPPS by estimating quantitative effects. This is expected to contribute to the proliferation of CPPS in the industry.

Smart environment architecture for emotion detection and regulation.

PubMed

Fernández-Caballero, Antonio; Martínez-Rodrigo, Arturo; Pastor, José Manuel; Castillo, José Carlos; Lozano-Monasor, Elena; López, María T; Zangróniz, Roberto; Latorre, José Miguel; Fernández-Sotos, Alicia

2016-12-01

This paper introduces an architecture as a proof-of-concept for emotion detection and regulation in smart health environments. The aim of the proposal is to detect the patient's emotional state by analysing his/her physiological signals, facial expression and behaviour. Then, the system provides the best-tailored actions in the environment to regulate these emotions towards a positive mood when possible. The current state-of-the-art in emotion regulation through music and colour/light is implemented with the final goal of enhancing the quality of life and care of the subject. The paper describes the three main parts of the architecture, namely "Emotion Detection", "Emotion Regulation" and "Emotion Feedback Control". "Emotion Detection" works with the data captured from the patient, whereas "Emotion Regulation" offers him/her different musical pieces and colour/light settings. "Emotion Feedback Control" performs as a feedback control loop to assess the effect of emotion regulation over emotion detection. We are currently testing the overall architecture and the intervention in real environments to achieve our final goal. Copyright © 2016 Elsevier Inc. All rights reserved.

Efficacy and safety of meditative movement therapies in fibromyalgia syndrome: a systematic review and meta-analysis of randomized controlled trials.

PubMed

Langhorst, Jost; Klose, Petra; Dobos, Gustav J; Bernardy, Kathrin; Häuser, Winfried

2013-01-01

A systematic review with meta-analysis of the efficacy and safety of meditative movement therapies (Qigong, Tai Chi and Yoga) in fibromyalgia syndrome (FMS) was carried out. We screened Clinicaltrials.Gov, Cochrane Library, PsycINFO, PubMed and Scopus (through December 2010) and the reference sections of original studies for meditative movement therapies (MMT) in FMS. Randomized controlled trials (RCT) comparing MMT to controls were analysed. Outcomes of efficacy were pain, sleep, fatigue, depression and health-related quality of life (HRQOL). Effects were summarized using standardized mean differences (SMD [95% confidence interval]). Outcomes of safety were drop out because of adverse events and serious adverse events. A total of 7 out of 117 studies with 362 subjects and a median of 12 sessions (range 8-24) were included. MMT reduced sleep disturbances (-0.61 [-0.95, -0.27]; 0.0004), fatigue (-0.66 [-0.99, -0.34]; <0.0001), depression (-0.49 [-0.76, -0.22]; 0.0004) and limitations of HRQOL (-0.59 [-0.93, -0.24]; 0.0009), but not pain (-0.35 [-0.80, 0.11]; 0.14) compared to controls at final treatment. The significant effects on sleep disturbances (-0.52 [-0.97, -0.07]; 0.02) and HRQOL (-0.66 [-1.31, -0.01]; 0.05) could be maintained after a median of 4.5 (range 3-6) months. In subgroup analyses, only Yoga yielded significant effects on pain, fatigue, depression and HRQOL at final treatment. Drop out rate because of adverse events was 3.1%. No serious adverse events were reported. MMT are safe. Yoga had short-term beneficial effects on some key domains of FMS. There is a need for high-quality studies with larger sample sizes to confirm the results.

[Effectiveness of short educational intervention in patients with insomnia in primary care].

PubMed

Gancedo-García, Ana; Gutiérrez-Antezana, Angélica Faviola; González-García, Pablo; Salinas-Herrero, Sally; Prieto-Merino, David; Suárez-Gil, Patricio

2014-12-01

To evaluate the effectiveness of providing an educational intervention in primary care (PC) alongside a pharmacological treatment for insomnia. Single blinded non randomised clinical trial. Two urban primary health centers in Gijón (Asturias, Spain). Patients who consulted for insomnia between July 2012-January 2013 and met the inclusion criteria (n=50) were assigned systematically to the control group (CG) or intervention group (IG). All patients initiated treatment with lorazepam 1mg in the evenings and had four weekly 15 min visits plus a follow-up visit after another month. The IG received training for control of stimuli, sleep hygiene and respiration and relaxation techniques in the four visits. The CG had only non invasive measures taken. Considering as cured those who reached a Pittsburgh Sleep Quality Index PSQI <6 or a 50% reduction from baseline level. It was also analyzed the change in the PSQI from baseline to final visit and to follow-up visit, and voluntary interruption of lorazepam. Analysis by Bayesian inference. Twelve out of recoveries after intervention against one out of 24 among control group. Mean change in PSQI to final visit and follow-up visit was: -4.7 (95%CrI:-5.9 to -3.5) and -6,3 (95%ICred: -7.5 to -5.1) in IG; -1.8 (95%ICred: -3 to -0.5) and -1.7 (95%ICred: -2.9 to -0.4) in CG. Interruption of lorazepan: in 4 controls (16,7%) and 9 (34,6%) in IG. Twenty nine patients in GI and 17 in GC completed the trial. Per protocol analysis showed similar results. The educational intervention in PC improves sleep quality and reduces the need of treatment with benzodiacepines. Copyright © 2013 Elsevier España, S.L.U. All rights reserved.

Implementation of Quality Assurance and Quality Control Measures in the National Phenology Database

NASA Astrophysics Data System (ADS)

Gerst, K.; Rosemartin, A.; Denny, E. G.; Marsh, L.; Barnett, L.

2015-12-01

The USA National Phenology Network (USA-NPN; www.usanpn.org) serves science and society by promoting a broad understanding of plant and animal phenology and the relationships among phenological patterns and environmental change. The National Phenology Database has over 5.5 million observation records for plants and animals for the period 1954-2015. These data have been used in a number of science, conservation and resource management applications, including national assessments of historical and potential future trends in phenology, regional assessments of spatio-temporal variation in organismal activity, and local monitoring for invasive species detection. Customizable data downloads are freely available, and data are accompanied by FGDC-compliant metadata, data-use and data-attribution policies, and vetted documented methodologies and protocols. The USA-NPN has implemented a number of measures to ensure both quality assurance and quality control. Here we describe the resources that have been developed so that incoming data submitted by both citizen and professional scientists are reliable; these include training materials, such as a botanical primer and species profiles. We also describe a number of automated quality control processes applied to incoming data streams to optimize data output quality. Existing and planned quality control measures for output of raw and derived data include: (1) Validation of site locations, including latitude, longitude, and elevation; (2) Flagging of records that conflict for a given date for an individual plant; (3) Flagging where species occur outside known ranges; (4) Flagging of records when phenophases occur outside of the plausible order for a species; (5) Flagging of records when intensity measures do not follow a plausible progression for a phenophase; (6) Flagging of records when a phenophase occurs outside of the plausible season, and (7) Quantification of precision and uncertainty for estimation of phenological metrics. Finally, we will describe preliminary work to develop methods for outlier detection that will inform plausibility checks. Ultimately we aim to maximize data quality of USA-NPN data and data products to ensure that this database can continue to be reliably applied for science and decision-making for multiple scales and applications.

Improving transcriptome construction in non-model organisms: integrating manual and automated gene definition in Emiliania huxleyi.

PubMed

Feldmesser, Ester; Rosenwasser, Shilo; Vardi, Assaf; Ben-Dor, Shifra

2014-02-22

The advent of Next Generation Sequencing technologies and corresponding bioinformatics tools allows the definition of transcriptomes in non-model organisms. Non-model organisms are of great ecological and biotechnological significance, and consequently the understanding of their unique metabolic pathways is essential. Several methods that integrate de novo assembly with genome-based assembly have been proposed. Yet, there are many open challenges in defining genes, particularly where genomes are not available or incomplete. Despite the large numbers of transcriptome assemblies that have been performed, quality control of the transcript building process, particularly on the protein level, is rarely performed if ever. To test and improve the quality of the automated transcriptome reconstruction, we used manually defined and curated genes, several of them experimentally validated. Several approaches to transcript construction were utilized, based on the available data: a draft genome, high quality RNAseq reads, and ESTs. In order to maximize the contribution of the various data, we integrated methods including de novo and genome based assembly, as well as EST clustering. After each step a set of manually curated genes was used for quality assessment of the transcripts. The interplay between the automated pipeline and the quality control indicated which additional processes were required to improve the transcriptome reconstruction. We discovered that E. huxleyi has a very high percentage of non-canonical splice junctions, and relatively high rates of intron retention, which caused unique issues with the currently available tools. While individual tools missed genes and artificially joined overlapping transcripts, combining the results of several tools improved the completeness and quality considerably. The final collection, created from the integration of several quality control and improvement rounds, was compared to the manually defined set both on the DNA and protein levels, and resulted in an improvement of 20% versus any of the read-based approaches alone. To the best of our knowledge, this is the first time that an automated transcript definition is subjected to quality control using manually defined and curated genes and thereafter the process is improved. We recommend using a set of manually curated genes to troubleshoot transcriptome reconstruction.

Medicare and Medicaid programs: Hospital Outpatient Prospective Payment and Ambulatory Surgical Center Payment Systems and Quality Reporting Programs; electronic reporting pilot; Inpatient Rehabilitation Facilities Quality Reporting Program; revision to Quality Improvement Organization regulations. Final rule with comment period.

PubMed

2012-11-15

This final rule with comment period revises the Medicare hospital outpatient prospective payment system (OPPS) and the Medicare ambulatory surgical center (ASC) payment system for CY 2013 to implement applicable statutory requirements and changes arising from our continuing experience with these systems. In this final rule with comment period, we describe the changes to the amounts and factors used to determine the payment rates for Medicare services paid under the OPPS and those paid under the ASC payment system. In addition, this final rule with comment period updates and refines the requirements for the Hospital Outpatient Quality Reporting (OQR) Program, the ASC Quality Reporting (ASCQR) Program, and the Inpatient Rehabilitation Facility (IRF) Quality Reporting Program. We are continuing the electronic reporting pilot for the Electronic Health Record (EHR) Incentive Program, and revising the various regulations governing Quality Improvement Organizations (QIOs), including the secure transmittal of electronic medical information, beneficiary complaint resolution and notification processes, and technical changes. The technical changes to the QIO regulations reflect CMS' commitment to the general principles of the President's Executive Order on Regulatory Reform, Executive Order 13563 (January 18, 2011).

Is arthrocentesis of temporomandibular joint with corticosteroids beneficial? A systematic review.

PubMed

Davoudi, A; Khaki, H; Mohammadi, I; Daneshmand, M; Tamizifar, A; Bigdelou, M; Ansaripoor, F

2018-05-01

Temporomandibular disorders (TMDs) are musculoskeletal conditions that can inhibit the normal function of temporomandibular joints (TMJs) and affect the patient's quality of life, negatively. Arthrocentesis (AC) is a minimally invasive surgical procedure used for treating TMDs. The aim of present paper is to evaluate the advantages of administrating corticosteroid (CS) during AC by reviewing high quality released articles. Searching on Cochrane Library, Web of Science, Google Scholar, PubMed, ProQuest, and Scopus databases were performed with focusing on proper key words. Related titles and abstracts, up to December 2017, were screened and selected based on inclusion criteria. The full text of all randomized controlled trials (RCTs) was extensively read and subjected to quality assessments. After initial search, a total of 2067 articles were included into the study. Finally, 7 studies were reliable enough in methodology and randomization to be included into the study. All of the observed studies showed improvements in jaw functions and pain relief with no statistical differences in both AC and control groups. One study reported painless maximum incisal opening in CS group than the control group. Based on available RCTs, the AC of TMJ with CS seems to result in similar findings to other therapeutic drugs, with no significant differences.

Defending the mitochondria: The pathways of mitophagy and mitochondrial-derived vesicles.

PubMed

Roberts, Rosalind F; Tang, Matthew Y; Fon, Edward A; Durcan, Thomas M

2016-10-01

Mitochondria are the powerhouses for the cell, consuming oxygen to generate sufficient energy for the maintenance of normal cellular processes. However, a deleterious consequence of this process are reactive oxygen species generated as side-products of these reactions. As a means to protect mitochondria from damage, cells and mitochondria have developed a wide-range of mitochondrial quality control mechanisms that remove damaged mitochondrial cargo, enabling the mitochondria to repair the damage and ultimately restore their normal function. If the damage is extensive and mitochondria can no longer be repaired, a process termed mitophagy is initiated in which the mitochondria are directed for autophagic clearance. Canonical mitophagy is regulated by two proteins, PINK1 and Parkin, which are mutated in familial forms of Parkinson's disease. In this review, we discuss recent work elucidating the mechanism of PINK1/Parkin-mediated mitophagy, along with recently uncovered PINK1/Parkin-independent mitophagy pathways. Moreover, we describe a novel mitochondrial quality control pathway, involving mitochondrial-derived vesicles that direct distinct and damaged mitochondrial cargo for degradation in the lysosome. Finally, we discuss the association between mitochondrial quality control, cardiac, hepatic and neurodegenerative disease and discuss the possibility of targeting these pathways for therapeutic purposes. Copyright © 2016 Elsevier Ltd. All rights reserved.

An Automated Treatment Plan Quality Control Tool for Intensity-Modulated Radiation Therapy Using a Voxel-Weighting Factor-Based Re-Optimization Algorithm.

PubMed

Song, Ting; Li, Nan; Zarepisheh, Masoud; Li, Yongbao; Gautier, Quentin; Zhou, Linghong; Mell, Loren; Jiang, Steve; Cerviño, Laura

2016-01-01

Intensity-modulated radiation therapy (IMRT) currently plays an important role in radiotherapy, but its treatment plan quality can vary significantly among institutions and planners. Treatment plan quality control (QC) is a necessary component for individual clinics to ensure that patients receive treatments with high therapeutic gain ratios. The voxel-weighting factor-based plan re-optimization mechanism has been proved able to explore a larger Pareto surface (solution domain) and therefore increase the possibility of finding an optimal treatment plan. In this study, we incorporated additional modules into an in-house developed voxel weighting factor-based re-optimization algorithm, which was enhanced as a highly automated and accurate IMRT plan QC tool (TPS-QC tool). After importing an under-assessment plan, the TPS-QC tool was able to generate a QC report within 2 minutes. This QC report contains the plan quality determination as well as information supporting the determination. Finally, the IMRT plan quality can be controlled by approving quality-passed plans and replacing quality-failed plans using the TPS-QC tool. The feasibility and accuracy of the proposed TPS-QC tool were evaluated using 25 clinically approved cervical cancer patient IMRT plans and 5 manually created poor-quality IMRT plans. The results showed high consistency between the QC report quality determinations and the actual plan quality. In the 25 clinically approved cases that the TPS-QC tool identified as passed, a greater difference could be observed for dosimetric endpoints for organs at risk (OAR) than for planning target volume (PTV), implying that better dose sparing could be achieved in OAR than in PTV. In addition, the dose-volume histogram (DVH) curves of the TPS-QC tool re-optimized plans satisfied the dosimetric criteria more frequently than did the under-assessment plans. In addition, the criteria for unsatisfied dosimetric endpoints in the 5 poor-quality plans could typically be satisfied when the TPS-QC tool generated re-optimized plans without sacrificing other dosimetric endpoints. In addition to its feasibility and accuracy, the proposed TPS-QC tool is also user-friendly and easy to operate, both of which are necessary characteristics for clinical use.

Quality of life, mood and seizure control in patients with brain tumor related epilepsy treated with lacosamide as add-on therapy: A prospective explorative study with a historical control group.

PubMed

Maschio, Marta; Zarabla, Alessia; Maialetti, Andrea; Fabi, Alessandra; Vidiri, Antonello; Villani, Veronica; Giannarelli, Diana

2017-08-01

Brain tumor-related epilepsy (BTRE) is often drug resistant and patients can be forced to take polytherapy that can adversely affect their quality of life (QoL). Lacosamide (LCM) is a new antiepileptic drug (AED) used as adjunctive therapy in patients with partial seizures with or without secondary generalization, with a favorable pharmacokinetic profile that seems to be effective and well tolerated. Therefore it represents a possible therapeutic choice for patients with BTRE. We propose a prospective study with a historical control group to evaluate the effect of LCM as add-on therapy on seizure control and quality of life in patients with BTRE. This study has been designed to test the superiority of Lacosamide over Levetiracetam as an add-on. We compared a prospective cohort of 25 patients treated with Lacosamide with a historical control group (n=19) treated with Levetiracetam as an add-on. We recruited 25 adult patients (M 18, F 7; mean age 41.9) affected by BTRE with uncontrolled partial-onset seizures treated with AED polytherapy. We added LCM as an add-on. Patients were evaluated at baseline, after 3months and at 6months. This population has been compared with a historical control group of 19 BTRE adult patients (M 13, F 6; median age 48.0, range: 28-70) with uncontrolled partial-onset seizures treated with LEV as add-on. The patients underwent QoL, mood and adverse events tests (Adverse Event Profile-AEP) and evaluation of seizure frequency. Twelve patients had high grade gliomas, and thirteen had low grade gliomas. During follow-up, thirteen patients underwent chemotherapy, three radiotherapy and five patients had disease progression. Nine patients had simple partial seizures, eight had complex partial seizures, and eight had secondary generalized seizures. Fifteen patients were in monotherapy and ten in polytherapy with AEDs. LCM was added up to reach the maximum dosage of 400mg/die (mean final dose 300mg/die). Four patients dropped out due to poor compliance and 1 for inefficacy. In the historical control group treated with LEV (mean final dose 2000mg/die) 12 patients had high-grade gliomas, and 7 had low grade gliomas. Thirteen patients were in monotherapy and 6 in polytherapy with AEDs. In the 22 patients evaluable of 25 patients treated with LCM, we observed at final follow-up 7 patients seizure free, 12 with a significant reduction of seizures≥50%, 2 stable and 1 patient with number of seizures increased. Mean seizure frequency at baseline compared with baseline period: the mean number of seizures significantly decreased from baseline (9.4) to final follow-up (1.2) (P=0.005). The Responder Rate was 86.4%. Comparing responder rate of 22 evaluable patients with LCM with responder rate of 19 patients with LEV we didn't observe significant differences (p=0.31). In our patients treated with LCM we didn't observe significant difference at 3 and 6months in QoL tests results; we observe a significant reduction in the mean score of Karnofsky Performance Status (KPS) and Barthel Index (BI) between baseline and 6months of follow-up (KPS p=0.003; BI p=0.007). No clinical side effects were observed. Comparing the LCM with the historical group treated with LEV in add-on, we observed that LCM seems to have a higher clinical efficacy than LEV. In our patients, we did not observe any significant changes in QoL tests, indicating stability in all quality of life domains explored, despite the objective worsening in their functional status. Although this is a small series with a relatively short follow-up, our data indicates that LCM in add-on in patients with BTRE appears to be as effective as LEV in add-on, without impact on mood and quality of life. Copyright © 2017 Elsevier Inc. All rights reserved.

Control design methods for floating wind turbines for optimal disturbance rejection

NASA Astrophysics Data System (ADS)

Lemmer, Frank; Schlipf, David; Cheng, Po Wen

2016-09-01

An analysis of the floating wind turbine as a multi-input-multi-output system investigating the effect of the control inputs on the system outputs is shown. These effects are compared to the ones of the disturbances from wind and waves in order to give insights for the selection of the control layout. The frequencies with the largest impact on the outputs due to limited effect of the controlled variables are identified. Finally, an optimal controller is designed as a benchmark and compared to a conventional PI-controller using only the rotor speed as input. Here, the previously found system properties, especially the difficulties to damp responses to wave excitation, are confirmed and verified through a spectral analysis with realistic environmental conditions. This comparison also assesses the quality of the employed simplified linear simulation model compared to the nonlinear model and shows that such an efficient frequency-domain evaluation for control design is feasible.

Nonlinear gearshifts control of dual-clutch transmissions during inertia phase.

PubMed

Hu, Yunfeng; Tian, Lu; Gao, Bingzhao; Chen, Hong

2014-07-01

In this paper, a model-based nonlinear gearshift controller is designed by the backstepping method to improve the shift quality of vehicles with a dual-clutch transmission (DCT). Considering easy-implementation, the controller is rearranged into a concise structure which contains a feedforward control and a feedback control. Then, robustness of the closed-loop error system is discussed in the framework of the input to state stability (ISS) theory, where model uncertainties are considered as the additive disturbance inputs. Furthermore, due to the application of the backstepping method, the closed-loop error system is ordered as a linear system. Using the linear system theory, a guideline for selecting the controller parameters is deduced which could reduce the workload of parameters tuning. Finally, simulation results and Hardware in the Loop (HiL) simulation are presented to validate the effectiveness of the designed controller. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

When life gives you lemons: The effectiveness of culinary group intervention among cancer patients.

PubMed

Barak-Nahum, Ayelet; Haim, Limor Ben; Ginzburg, Karni

2016-10-01

Previous studies have shown that the dietary habits of cancer patients and survivors have significant implications for their recovery and quality of life. The current study examined the effectiveness of an innovative culinary group intervention on cancer patients' quality of life through changes in their eating behaviors, as manifested by an increase in their tendency towards intuitive eating and healthy food choices. In total, 190 cancer patients participated in this study, and were allocated to an intervention or a wait-list control group. A battery of self-report questionnaires assessing food choices, intuitive eating, health-related quality of life, and subjective well-being was administered at two time points: Before the intervention (T1) and at the end of the three month intervention (T2). Analyses revealed an increase in health-related quality of life and well-being among the intervention group. Intuitive eating and healthy food choices also increased among the intervention but not wait-list control group. Finally, results indicated that participation in the culinary group intervention and improvements in health-related quality of life and well-being were mediated by changes in eating behaviors. Our findings demonstrate that nutrition and eating behaviors have a significant effect on cancer patients' physical and emotional adjustment. A culinary group intervention seems to target patients' physical and emotional needs and promote their adjustment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Medicare program; inpatient psychiatric facilities prospective payment system--update for fiscal year beginning October 1, 2014 (FY 2015). Final rule.

PubMed

2014-08-06

This final rule will update the prospective payment rates for Medicare inpatient hospital services provided by inpatient psychiatric facilities (IPFs). These changes will be applicable to IPF discharges occurring during the fiscal year (FY) beginning October 1, 2014 through September 30, 2015. This final rule will also address implementation of ICD-10-CM and ICD-10-PCS codes; finalize a new methodology for updating the cost of living adjustment (COLA), and finalize new quality measures and reporting requirements under the IPF quality reporting program.

Quality and rural-urban comparison of tuberculosis care in Rivers State, Nigeria.

PubMed

Tobin-West, Charles Ibiene; Isodje, Anastasia

2016-01-01

Nigeria ranks among countries with the highest burden of tuberculosis. Yet evidence continues to indicate poor treatment outcomes which have been attributed to poor quality of care. This study aims to identify some of the systemic problems in order to inform policy decisions for improved quality of services and treatment outcomes in Nigeria. A comparative assessment of the quality of TB care in rural and urban health facilities was carried out between May and June 2013, employing the Donabedian model of quality assessment. Data was analysed using the SPSS software package version 20.0. The level of significance was set at p < 0.05. Health facility infrastructures were more constrained in the urban than rural settings. Both the urban and rural facilities lacked adequate facilities for infection control such as, running water, air filter respirators, hand gloves and extractor fans. Health education and HIV counselling and testing (HCT) were limited in rural facilities compared to urban facilities. Although anti-TB drugs were generally available in both settings, the DOTS strategy in patient care was completely ignored. Finally, laboratory support for diagnosis and patient monitoring was limited in the rural facilities. The study highlights suboptimal quality of TB care in Rivers State with limitations in health education and HCT of patients for HIV as well as laboratory support for TB care in rural health facilities. We, therefore, recommend that adequate infection control measures, strict observance of the DOTS strategy and sufficient laboratory support be provided to TB clinics in the State.

Medicare program; FY 2014 hospice wage index and payment rate update; hospice quality reporting requirements; and updates on payment reform. final rule.

PubMed

2013-08-07

This final rule updates the hospice payment rates and the wage index for fiscal year (FY) 2014, and continues the phase out of the wage index budget neutrality adjustment factor (BNAF). Including the FY 2014 15 percent BNAF reduction, the total 5 year cumulative BNAF reduction in FY 2014 will be 70 percent. The BNAF phase-out will continue with successive 15 percent reductions in FY 2015 and FY 2016. This final rule also clarifies how hospices are to report diagnoses on hospice claims, and provides updates to the public on hospice payment reform. Additionally, this final rule changes the requirements for the hospice quality reporting program by discontinuing currently reported measures and implementing a Hospice Item Set with seven National Quality Forum (NFQ) endorsed measures beginning July 1, 2014, as proposed. Finally, this final rule will implement the hospice Experience of Care Survey on January 1, 2015, as proposed.

Improvements in the order, isotropy and electron density of glypican-1 crystals by controlled dehydration.

PubMed

Awad, Wael; Svensson Birkedal, Gabriel; Thunnissen, Marjolein M G M; Mani, Katrin; Logan, Derek T

2013-12-01

The use of controlled dehydration for improvement of protein crystal diffraction quality is increasing in popularity, although there are still relatively few documented examples of success. A study has been carried out to establish whether controlled dehydration could be used to improve the anisotropy of crystals of the core protein of the human proteoglycan glypican-1. Crystals were subjected to controlled dehydration using the HC1 device. The optimal protocol for dehydration was developed by careful investigation of the following parameters: dehydration rate, final relative humidity and total incubation time Tinc. Of these, the most important was shown to be Tinc. After dehydration using the optimal protocol the crystals showed significantly reduced anisotropy and improved electron density, allowing the building of previously disordered parts of the structure.

Manipulation of follicle development to ensure optimal oocyte quality and conception rates in cattle.

PubMed

Baruselli, P S; Sá Filho, M F; Ferreira, R M; Sales, J N S; Gimenes, L U; Vieira, L M; Mendanha, M F; Bó, G A

2012-08-01

Over the last several decades, a number of therapies have been developed that manipulate ovarian follicle growth to improve oocyte quality and conception rates in cattle. Various strategies have been proposed to improve the responses to reproductive biotechnologies following timed artificial insemination (TAI), superovulation (SOV) or ovum pickup (OPU) programmes. During TAI protocols, final follicular growth and size of the ovulatory follicle are key factors that may significantly influence oocyte quality, ovulation, the uterine environment and consequently pregnancy outcomes. Progesterone concentrations during SOV protocols influence follicular growth, oocyte quality and embryo quality; therefore, several adjustments to SOV protocols have been proposed depending on the animal category and breed. In addition, the success of in vitro embryo production is directly related to the number and quality of cumulus oocyte complexes harvested by OPU. Control of follicle development has a significant impact on the OPU outcome. This article discusses a number of key points related to the manipulation of ovarian follicular growth to maximize oocyte quality and improve conception rates following TAI and embryo transfer of in vivo- and in vitro-derived embryos in cattle. © 2012 Blackwell Verlag GmbH.

Quality in laboratory medicine: 50years on.

PubMed

Plebani, Mario

2017-02-01

The last 50years have seen substantial changes in the landscape of laboratory medicine: its role in modern medicine is in evolution and the quality of laboratory services is changing. The need to control and improve quality in clinical laboratories has grown hand in hand with the growth in technological developments leading to an impressive reduction of analytical errors over time. An essential cause of this impressive improvement has been the introduction and monitoring of quality indicators (QIs) such as the analytical performance specifications (in particular bias and imprecision) based on well-established goals. The evolving landscape of quality and errors in clinical laboratories moved first from analytical errors to all errors performed within the laboratory walls, subsequently to errors in laboratory medicine (including errors in test requesting and result interpretation), and finally, to a focus on errors more frequently associated with adverse events (laboratory-associated errors). After decades in which clinical laboratories have focused on monitoring and improving internal indicators of analytical quality, efficiency and productivity, it is time to shift toward indicators of total quality, clinical effectiveness and patient outcomes. Copyright © 2016 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

The effect of low and moderate intensity aerobic exercises on sleep quality in men older adults.

PubMed

Akbari Kamrani, Ahmad Ali; Shams, Amir; Shamsipour Dehkordi, Parvaneh; Mohajeri, Robabeh

2014-03-01

Sleep is an active and complex rhythmic state that may be affected by the aging process. The purpose of present research was to investigate the effect of low and moderate intensity aerobic exercises on sleep quality in older adults. The research method is quasi-experimental with pre-test and post-test design. The statistical sample included 45 volunteer elderly men with age range of 60-70 years-old that divided randomly in two experimental groups (aerobic exercise with low and moderate intensity) and one control group. In each group selected 15 older adults based on inclusion and exclusion criteria (such as, without sleep apnea, not smoking, and no taking hypnotic drugs). First, all subjects were evaluated by a doctor to confirm their physical and mental health. Also, the maximum heart rate (MaxHR) of subjects was obtained by subtracting one's age from 220. Furthermore, based on aerobic exercise type (40-50% MaxHR for low intensity group and 60-70% MaxHR for moderate intensity group) the target MaxHR was calculated for each subject. The exercise protocol consisted of 8 weeks aerobic exercises (2 sessions in per-week) based on Rockport one-mile walking/running test and the control group continued their daily activities. All subjects in per-test and post-test stages completed the Petersburg Sleep Quality Index (PSQI). In pre-test stage, results showed that there were no significant differences between control and experimental groups in sleep quality and its components (P>0.05). On the other hand, results in post-test stage showed that there were significant differences between control and experimental groups in these variables (P<0.05). Also, the Tukey Post Hoc showed that the moderate intensity group scores in total sleep quality and its components were better than other groups (P<0.05). Finally, the low intensity group scores in total sleep quality and its components were better than control group (P<0.05). Generally, the present research showed that the aerobic exercises with moderate intensity (60-70% MaxHR) have a positive and significant effect on sleep quality and its components. Thus, based on these findings, the aerobic exercises with moderate intensity is a useful to improve the sleep quality and its components among community older adults were recommended.

Rocky Mountain Arsenal, Sections 26 and 25 Contamination Survey. Phase 1

DTIC Science & Technology

1987-12-01

mapping specifications for scale, overlap, density, and image quality. Utilizing the aerial photography and ground control described above, orthophoto ...base maps with superimposed contours will be prepared. £ 3-2 RMA06-D.1/TPGEO 1.3 11/20/87 Orthophoto negatives will be prepared directly at the final...cdial lnvestigation/Feasibiliy Studv (RI/FS) at tile Rocky Mountain Arsenal. Tasks 4 and 6 were prepared by ’Environmental Science and Engineering (ESE

Shuttle Mission STS-50: Orbital Processing of High-Quality CdTe Compound Semiconductors Experiment: Final Flight Sample Characterization Report

NASA Technical Reports Server (NTRS)

Larson, David J.; Casagrande, Luis G.; DiMarzio, Don; Alexander, J. Iwan D.; Carlson, Fred; Lee, Taipo; Dudley, Michael; Raghathamachar, Balaji

1998-01-01

The Orbital Processing of High-Quality Doped and Alloyed CdTe Compound Semiconductors program was initiated to investigate, quantitatively, the influences of gravitationally dependent phenomena on the growth and quality of bulk compound semiconductors. The objective was to improve crystal quality (both structural and compositional) and to better understand and control the variables within the crystal growth production process. The empirical effort entailed the development of a terrestrial (one-g) experiment baseline for quantitative comparison with microgravity (mu-g) results. This effort was supported by the development of high-fidelity process models of heat transfer, fluid flow and solute redistribution, and thermo-mechanical stress occurring in the furnace, safety cartridge, ampoule, and crystal throughout the melting, seeding, crystal growth, and post-solidification processing. In addition, the sensitivity of the orbital experiments was analyzed with respect to the residual microgravity (mu-g) environment, both steady state and g-jitter. CdZnTe crystals were grown in one-g and in mu-g. Crystals processed terrestrially were grown at the NASA Ground Control Experiments Laboratory (GCEL) and at Grumman Aerospace Corporation (now Northrop Grumman Corporation). Two mu-g crystals were grown in the Crystal Growth Furnace (CGF) during the First United States Microgravity Laboratory Mission (USML-1), STS-50, June 24 - July 9, 1992.

Effect of spent mushroom substrate as a bulking agent on gaseous emissions and compost quality during pig manure composting.

PubMed

Li, Shuyan; Li, Danyang; Li, Jijin; Li, Yangyang; Li, Guoxue; Zang, Bing; Li, Yun

2018-05-01

The aim of this study was to investigate the gaseous emissions (CH 4 , N 2 O, and NH 3 ) and compost quality during the pig manure composting by adding spent mushroom substrate (SMS) as a bulking agent. The control treatment was also studied using corn stalk (CS) as a bulking agent. The experiment was conducted in a pilot scale composting reactor under aerobic condition with the initial C/N ratio of 20. Results showed that bulking agents significantly affected gaseous emissions and compost quality. Using SMS as a bulking agent improved composting efficiency by shortening the time for maturity. SMS increased germination index and humic acid of the final compost (by 13.44 and 41.94%, respectively) compared with CS. Furthermore, composting with SMS as a bulking agent could reduce nitrogen loss, NH 3 , and N 2 O emissions (by 13.57, 35.56, and 46.48%, respectively) compared with the control. SMS slightly increased CH 4 emission about 1.1 times of the CS. However, a 33.95% decrease in the global warming potential of CH 4 and N 2 O was obtained by adding SMS treatment. These results indicate that SMS is a favorable bulking agent for reducing gaseous emissions and increasing compost quality.

Spatial regression test for ensuring temperature data quality in southern Spain

NASA Astrophysics Data System (ADS)

Estévez, J.; Gavilán, P.; García-Marín, A. P.

2018-01-01

Quality assurance of meteorological data is crucial for ensuring the reliability of applications and models that use such data as input variables, especially in the field of environmental sciences. Spatial validation of meteorological data is based on the application of quality control procedures using data from neighbouring stations to assess the validity of data from a candidate station (the station of interest). These kinds of tests, which are referred to in the literature as spatial consistency tests, take data from neighbouring stations in order to estimate the corresponding measurement at the candidate station. These estimations can be made by weighting values according to the distance between the stations or to the coefficient of correlation, among other methods. The test applied in this study relies on statistical decision-making and uses a weighting based on the standard error of the estimate. This paper summarizes the results of the application of this test to maximum, minimum and mean temperature data from the Agroclimatic Information Network of Andalusia (southern Spain). This quality control procedure includes a decision based on a factor f, the fraction of potential outliers for each station across the region. Using GIS techniques, the geographic distribution of the errors detected has been also analysed. Finally, the performance of the test was assessed by evaluating its effectiveness in detecting known errors.

76 FR 41561 - Approval and Promulgation of Implementation Plans; California; 2007 South Coast PM2.5

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-14

...EPA is proposing to approve in part and disapprove in part state implementation plan (SIP) revisions submitted by California to provide for attainment of the 1997 fine particulate matter (PM2.5) national ambient air quality standards in the Los Angeles-South Coast area (South Coast). These SIP revisions are the South Coast 2007 Air Quality Management Plan (South Coast 2007 AQMP) (revised 2011) and South Coast-related provisions of the 2007 State Strategy (revised 2009 and 2011). EPA is proposing to approve the emissions inventories; air quality modeling; reasonably available control measures/reasonably available control technology demonstration; the reasonable further progress and attainment demonstrations; and the transportation conformity motor vehicle emissions budgets. EPA is also proposing to grant California's request to extend the attainment deadline for the South Coast to April 5, 2015 and to approve commitments to measures and reductions by the South Coast Air Quality Management District and the California Air Resources Board. Finally, we are proposing to disapprove the SIP's contingency measures and to reject the assignment of 10 tpd of NOX reductions to the federal government. This proposed rule amends EPA's November 22, 2010 proposed rule (75 FR 91294) on the South Coast PM2.5 plan and 2007 State strategy.

Design verification and fabrication of active control systems for the DAST ARW-2 high aspect ratio wing, part 1

NASA Technical Reports Server (NTRS)

Mcgehee, C. R.

1986-01-01

A study was conducted under Drones for Aerodynamic and Structural Testing (DAST) program to accomplish the final design and hardware fabrication for four active control systems compatible with and ready for installation in the NASA Aeroelastic Research Wing No. 2 (ARW-2) and Firebee II drone flight test vehicle. The wing structure was designed so that Active Control Systems (ACS) are required in the normal flight envelope by integrating control system design with aerodynamics and structure technologies. The DAST ARW-2 configuration uses flutter suppression, relaxed static stability, and gust and maneuver load alleviation ACS systems, and an automatic flight control system. Performance goals and criteria were applied to individual systems and the systems collectively to assure that vehicle stability margins, flutter margins, flying qualities and load reductions are achieved.

Valid internal standard technique for arson detection based on gas chromatography-mass spectrometry.

PubMed

Salgueiro, Pedro A S; Borges, Carlos M F; Bettencourt da Silva, Ricardo J N

2012-09-28

The most popular procedures for the detection of residues of accelerants in fire debris are the ones published by the American Society for Testing and Materials (ASTM E1412-07 and E1618-10). The most critical stages of these tests are the conservation of fire debris from the sampling to the laboratory, the extraction of residues of accelerants from the debris to the activated charcoal strips (ACS) and from those to the final solvent, as well as the analysis of sample extract by gas chromatography-mass spectrometry (GC-MS) and the interpretation of the instrumental signal. This work proposes a strategy for checking the quality of the sample conservation, the accelerant residues transference to final solvent and GC-MS analysis, using internal standard additions. It is used internal standards ranging from a highly volatile compound for checking debris conservation to low volatile compound for checking GC-MS repeatability. The developed quality control (QC) parameters are not affected by GC-MS sensitivity variation and, specifically, the GC-MS performance control is not affected by ACS adsorption saturation that may mask test performance deviations. The proposed QC procedure proved to be adequate to check GC-MS repeatability, ACS extraction and sample conservation since: (1) standard additions are affected by negligible uncertainty and (2) observed dispersion of QC parameters are fit for its intended use. Copyright © 2012 Elsevier B.V. All rights reserved.

Thresholds of Toxicological Concern for cosmetics-related substances: New database, thresholds, and enrichment of chemical space.

PubMed

Yang, Chihae; Barlow, Susan M; Muldoon Jacobs, Kristi L; Vitcheva, Vessela; Boobis, Alan R; Felter, Susan P; Arvidson, Kirk B; Keller, Detlef; Cronin, Mark T D; Enoch, Steven; Worth, Andrew; Hollnagel, Heli M

2017-11-01

A new dataset of cosmetics-related chemicals for the Threshold of Toxicological Concern (TTC) approach has been compiled, comprising 552 chemicals with 219, 40, and 293 chemicals in Cramer Classes I, II, and III, respectively. Data were integrated and curated to create a database of No-/Lowest-Observed-Adverse-Effect Level (NOAEL/LOAEL) values, from which the final COSMOS TTC dataset was developed. Criteria for study inclusion and NOAEL decisions were defined, and rigorous quality control was performed for study details and assignment of Cramer classes. From the final COSMOS TTC dataset, human exposure thresholds of 42 and 7.9 μg/kg-bw/day were derived for Cramer Classes I and III, respectively. The size of Cramer Class II was insufficient for derivation of a TTC value. The COSMOS TTC dataset was then federated with the dataset of Munro and colleagues, previously published in 1996, after updating the latter using the quality control processes for this project. This federated dataset expands the chemical space and provides more robust thresholds. The 966 substances in the federated database comprise 245, 49 and 672 chemicals in Cramer Classes I, II and III, respectively. The corresponding TTC values of 46, 6.2 and 2.3 μg/kg-bw/day are broadly similar to those of the original Munro dataset. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Air quality mapping using GIS and economic evaluation of health impact for Mumbai City, India.

PubMed

Kumar, Awkash; Gupta, Indrani; Brandt, Jørgen; Kumar, Rakesh; Dikshit, Anil Kumar; Patil, Rashmi S

2016-05-01

Mumbai, a highly populated city in India, has been selected for air quality mapping and assessment of health impact using monitored air quality data. Air quality monitoring networks in Mumbai are operated by National Environment Engineering Research Institute (NEERI), Maharashtra Pollution Control Board (MPCB), and Brihanmumbai Municipal Corporation (BMC). A monitoring station represents air quality at a particular location, while we need spatial variation for air quality management. Here, air quality monitored data of NEERI and BMC were spatially interpolated using various inbuilt interpolation techniques of ArcGIS. Inverse distance weighting (IDW), Kriging (spherical and Gaussian), and spline techniques have been applied for spatial interpolation for this study. The interpolated results of air pollutants sulfur dioxide (SO2), nitrogen dioxide (NO2) and suspended particulate matter (SPM) were compared with air quality data of MPCB in the same region. Comparison of results showed good agreement for predicted values using IDW and Kriging with observed data. Subsequently, health impact assessment of a ward was carried out based on total population of the ward and air quality monitored data within the ward. Finally, health cost within a ward was estimated on the basis of exposed population. This study helps to estimate the valuation of health damage due to air pollution. Operating more air quality monitoring stations for measurement of air quality is highly resource intensive in terms of time and cost. The appropriate spatial interpolation techniques can be used to estimate concentration where air quality monitoring stations are not available. Further, health impact assessment for the population of the city and estimation of economic cost of health damage due to ambient air quality can help to make rational control strategies for environmental management. The total health cost for Mumbai city for the year 2012, with a population of 12.4 million, was estimated as USD8000 million.

An empirical evaluation of software quality assurance practices and challenges in a developing country: a comparison of Nigeria and Turkey.

PubMed

Sowunmi, Olaperi Yeside; Misra, Sanjay; Fernandez-Sanz, Luis; Crawford, Broderick; Soto, Ricardo

2016-01-01

The importance of quality assurance in the software development process cannot be overemphasized because its adoption results in high reliability and easy maintenance of the software system and other software products. Software quality assurance includes different activities such as quality control, quality management, quality standards, quality planning, process standardization and improvement amongst others. The aim of this work is to further investigate the software quality assurance practices of practitioners in Nigeria. While our previous work covered areas on quality planning, adherence to standardized processes and the inherent challenges, this work has been extended to include quality control, software process improvement and international quality standard organization membership. It also makes comparison based on a similar study carried out in Turkey. The goal is to generate more robust findings that can properly support decision making by the software community. The qualitative research approach, specifically, the use of questionnaire research instruments was applied to acquire data from software practitioners. In addition to the previous results, it was observed that quality assurance practices are quite neglected and this can be the cause of low patronage. Moreover, software practitioners are neither aware of international standards organizations or the required process improvement techniques; as such their claimed standards are not aligned to those of accredited bodies, and are only limited to their local experience and knowledge, which makes it questionable. The comparison with Turkey also yielded similar findings, making the results typical of developing countries. The research instrument used was tested for internal consistency using the Cronbach's alpha, and it was proved reliable. For the software industry in developing countries to grow strong and be a viable source of external revenue, software assurance practices have to be taken seriously because its effect is evident in the final product. Moreover, quality frameworks and tools which require minimum time and cost are highly needed in these countries.

Internal quality control: best practice.

PubMed

Kinns, Helen; Pitkin, Sarah; Housley, David; Freedman, Danielle B

2013-12-01

There is a wide variation in laboratory practice with regard to implementation and review of internal quality control (IQC). A poor approach can lead to a spectrum of scenarios from validation of incorrect patient results to over investigation of falsely rejected analytical runs. This article will provide a practical approach for the routine clinical biochemistry laboratory to introduce an efficient quality control system that will optimise error detection and reduce the rate of false rejection. Each stage of the IQC system is considered, from selection of IQC material to selection of IQC rules, and finally the appropriate action to follow when a rejection signal has been obtained. The main objective of IQC is to ensure day-to-day consistency of an analytical process and thus help to determine whether patient results are reliable enough to be released. The required quality and assay performance varies between analytes as does the definition of a clinically significant error. Unfortunately many laboratories currently decide what is clinically significant at the troubleshooting stage. Assay-specific IQC systems will reduce the number of inappropriate sample-run rejections compared with the blanket use of one IQC rule. In practice, only three or four different IQC rules are required for the whole of the routine biochemistry repertoire as assays are assigned into groups based on performance. The tools to categorise performance and assign IQC rules based on that performance are presented. Although significant investment of time and education is required prior to implementation, laboratories have shown that such systems achieve considerable reductions in cost and labour.

Identification of long-term trends and seasonality in high-frequency water quality data from the Yangtze River basin, China

PubMed Central

He, Bin; Chen, Yaning; Zou, Shan; Wang, Yi; Nover, Daniel; Chen, Wen; Yang, Guishan

2018-01-01

Comprehensive understanding of the long-term trends and seasonality of water quality is important for controlling water pollution. This study focuses on spatio-temporal distributions, long-term trends, and seasonality of water quality in the Yangtze River basin using a combination of the seasonal Mann-Kendall test and time-series decomposition. The used weekly water quality data were from 17 environmental stations for the period January 2004 to December 2015. Results show gradual improvement in water quality during this period in the Yangtze River basin and greater improvement in the Uppermost Yangtze River basin. The larger cities, with high GDP and population density, experienced relatively higher pollution levels due to discharge of industrial and household wastewater. There are higher pollution levels in Xiang and Gan River basins, as indicated by higher NH4-N and CODMn concentrations measured at the stations within these basins. Significant trends in water quality were identified for the 2004–2015 period. Operations of the three Gorges Reservoir (TGR) enhanced pH fluctuations and possibly attenuated CODMn, and NH4-N transportation. Finally, seasonal cycles of varying strength were detected for time-series of pollutants in river discharge. Seasonal patterns in pH indicate that maxima appear in winter, and minima in summer, with the opposite true for CODMn. Accurate understanding of long-term trends and seasonality are necessary goals of water quality monitoring system efforts and the analysis methods described here provide essential information for effectively controlling water pollution. PMID:29466354

Irrigation dose and plant density affect the volatile composition and sensory quality of dill (Anethum graveolens L.).

PubMed

El-Zaeddi, Hussein; Martínez-Tomé, Juan; Calín-Sánchez, Ángel; Burló, Francisco; Carbonell-Barrachina, Ángel A

2017-01-01

Two independent field experiments were carried out to investigate the influence of (i) three irrigation treatments (ID0 = 1585 m 3 ha -1 , considered as a control; ID1 = 1015 m 3 ha -1 ; and ID2 = 2180 m 3 ha -1 ) and (ii) three plant density treatments (PD0 = 5.56 plants m -2 , considered as a control; PD1 = 4.44 plants m -2 ; and PD2 = 7.41 plants m -2 ) on the production, volatile composition of essential oil, and sensory quality of dill. The highest plant yield was obtained with intermediate conditions of both irrigation dose (ID0) and plant density (PD0). The main compounds of the essential oil were α-phellandrene, dill ether and β-phellandrene. The highest irrigation dose (ID2) produced the highest concentrations of most of the main compounds: α-phellandrene (49.5 mg per 100 g), β-phellandrene (6.89 mg per 100 g) and limonene (2.49 mg per 100 g). A similar pattern was found for the highest plant density (PD2): α-phellandrene (71.0 mg per 100 g), dill ether (16.7 mg per 100 g) and β-phellandrene (9.70 mg per 100 g). The use of descriptive sensory analysis helped in reaching a final decision, and the dill plants with the highest sensory quality were those of the ID2 and PD0 treatments. The final recommendation is to use the irrigation dose ID2 and the plant density PD2 if the objective is to produce dill samples with the highest aromatic and sensory quality; however, if the only objective is to produce high amounts of dill, the best options are ID0 and PD0. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

The development of 'Quality of Life Instrument for Indian Diabetes patients (QOLID): a validation and reliability study in middle and higher income groups.

PubMed

Nagpal, Jitender; Kumar, Arvind; Kakar, Sonia; Bhartia, Abhishek

2010-05-01

To develop a reliable and valid quality of life questionnaire for Indian patients with diabetes. A draft of 75 questions was prepared on the basis of expert opinion, focus group discussions, review of existing literature and detailed semi-structured interviews of patients with diabetes with the intention of including all aspects of diabetes-specific and quality of life considered relevant by patients and care providers to enable constrict validity. A Stage 2 questionnaire was then prepared with 13 domains and 54 items (questions) after expert panel review for obvious irrelevance and duplication of issues. It was administered to 150 participants visiting a diabetes center at New Delhi. Factor analysis was done using principal component method with varimax rotation. Reliability analysis was done by calculating Cronbach's Alpha. For evaluating concordant validity the questionnaire was co-administered with DQL-CTQ to 30 participants. The discriminant validity of the questionnaire was tested using 't' test for metabolic control, co-morbidities, insulin use and gender. Using principal component method 8 domains were identified on the basis of an apriori hypothesis and the scree plot. These 8 domains explained 49.9% of the total variation. 34 items (questions) were selected to represent these domains on the basis of extraction communality, factor loading, inter-item and item-total correlations. The final questionnaire has an Overall Cronbach's Alpha value of 0.894 (subscale- 0.55 to 0.85) showing high internal consistency. The questionnaire showed good concordance (product moment correlation 0.724; p = 0.001; subscale correlation - 0.457 to 0.779) with the DQL-CTQ. The overall standardized questionnaire score showed good responsiveness to metabolic control and co-morbidities establishing discriminant validity. The final version of questionnaire with 8 domains and 34 items is a reliable and valid tool for assessment of quality of life of Indian patients with diabetes.

76 FR 41337 - Approval and Promulgation of Implementation Plans; California; 2008 San Joaquin Valley PM2.5

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-13

...EPA is proposing to approve in part and disapprove in part state implementation plan (SIP) revisions submitted by California to provide for attainment of the 1997 fine particulate matter (PM2.5) national ambient air quality standards in the San Joaquin Valley (SJV). These SIP revisions are the SJV 2008 PM2.5 Plan (revised 2010 and 2011) and SJV-related provisions of the 2007 State Strategy (revised 2009 and 2011). EPA is proposing to approve the emissions inventories; air quality modeling; the reasonably available control measures/reasonably available control technology, reasonable further progress, and attainment demonstrations; and the transportation conformity motor vehicle emissions budgets. EPA is also proposing to grant California's request to extend the attainment deadline for the SJV to April 5, 2015 and to approve commitments to measures and reductions by the SJV Air Pollution Control District and the California Air Resources Board. Finally, it is proposing to disapprove the SIP's contingency measures. This proposed rule amends EPA's November 30, 2010 proposed rule (75 FR 74518) on the SJV 2008 PM2.5 Plan and 2007 State Strategy.

Fact Sheet: Notice of Ambient Water Quality Criteria Document for Tributyltin (TBT) - Final

EPA Pesticide Factsheets

Information pertaining to 2004 Final Acute and Chronic Ambient Aquatic Life Water Quality Criteria for Tributyltin (TBT) for freshwater and saltwater. This fact sheet includes the safe levels of TBT that should protect the majority of species.

75 FR 45606 - Interagency Ocean Policy Task Force-Final Recommendations of the Interagency Ocean Policy Task Force

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-03

... COUNCIL ON ENVIRONMENTAL QUALITY Interagency Ocean Policy Task Force--Final Recommendations of the Interagency Ocean Policy Task Force AGENCY: Council on Environmental Quality. ACTION: Notice of Availability, Interagency Ocean Policy Task Force's [[Page 45607

Use of the MATRIXx Integrated Toolkit on the Microwave Anisotropy Probe Attitude Control System

NASA Technical Reports Server (NTRS)

Ward, David K.; Andrews, Stephen F.; McComas, David C.; ODonnell, James R., Jr.

1999-01-01

Recent advances in analytical software tools allow the analysis, simulation, flight code, and documentation of an algorithm to be generated from a single source, all within one integrated analytical design package. NASA's Microwave Anisotropy Probe project has used one such package, Integrated Systems' MATRIXx suite, in the design of the spacecraft's Attitude Control System. The project's experience with the linear analysis, simulation, code generation, and documentation tools will be presented and compared with more traditional development tools. In particular, the quality of the flight software generated will be examined in detail. Finally, lessons learned on each of the tools will be shared.

Stoichiometry control of complex oxides by sequential pulsed-laser deposition from binary-oxide targets

DOE PAGES

Herklotz, A.; Dörr, Kathrin; Ward, T. Z.; ...

2015-04-03

In this paper, to have precise atomic layer control over interfaces, we examine the growth of complex oxides through the sequential deposition from binary targets by pulsed laser deposition. In situ reflection high-energy electron diffraction (RHEED) is used to control the growth and achieve films with excellent structural quality. The growth from binary oxide targets is fundamentally different from single target growth modes and shows more similarities to shuttered growth by molecular beam epitaxy. The RHEED intensity oscillations of non-stoichiometric growth are consistent with a model of island growth and accumulation of excess material on the surface that can bemore » utilized to determine the correct stoichiometry for growth. Correct monolayer doses can be determined through an envelope frequency in the RHEED intensity oscillations. In order to demonstrate the ability of this growth technique to create complex heterostructures, the artificial n = 2 and 3 Sr n +1Ti n O 3 n +1 Ruddlesden-Popper phases are grown with good long-range order. Finally, this method enables the precise unit-cell level control over the structure of perovskite-type oxides, and thus the growth of complex materials with improved structural quality and electronic functionality.« less

A DMAIC approach for process capability improvement an engine crankshaft manufacturing process

NASA Astrophysics Data System (ADS)

Sharma, G. V. S. S.; Rao, P. Srinivasa

2014-05-01

The define-measure-analyze-improve-control (DMAIC) approach is a five-strata approach, namely DMAIC. This approach is the scientific approach for reducing the deviations and improving the capability levels of the manufacturing processes. The present work elaborates on DMAIC approach applied in reducing the process variations of the stub-end-hole boring operation of the manufacture of crankshaft. This statistical process control study starts with selection of the critical-to-quality (CTQ) characteristic in the define stratum. The next stratum constitutes the collection of dimensional measurement data of the CTQ characteristic identified. This is followed by the analysis and improvement strata where the various quality control tools like Ishikawa diagram, physical mechanism analysis, failure modes effects analysis and analysis of variance are applied. Finally, the process monitoring charts are deployed at the workplace for regular monitoring and control of the concerned CTQ characteristic. By adopting DMAIC approach, standard deviation is reduced from 0.003 to 0.002. The process potential capability index ( C P) values improved from 1.29 to 2.02 and the process performance capability index ( C PK) values improved from 0.32 to 1.45, respectively.

Does quality improvement work? Evaluation of the Organ Donation Breakthrough Collaborative.

PubMed

Howard, David H; Siminoff, Laura A; McBride, Virginia; Lin, Monica

2007-12-01

The Organ Donation Breakthrough Collaborative is a quality improvement initiative to encourage adoption of "best practices" for identifying potential donors and obtaining consent for deceased organ donation. We evaluate the impact of the first phase on organ donation rates. We study donation rates in the 95 hospitals that participated in the first phase and a control group of 125 hospitals. We use a controlled pre/post design. The preperiod is the year before the start of the Collaborative (September 2002 to August 2003), the postperiod is the final 6 months of the first phase (March 2004 to August 2004). We use administrative data from the Organ Procurement and Transplantation Network to compute the conversion rate in each hospital group and time period. The conversion rate is the proportion of eligible donors who became actual donors. Preperiod conversion rates in Collaborative and control hospitals were similar: 52 and 51 percent, respectively. In the postperiod, the conversion rate increased to 60 percent among Collaborative hospitals and remained at 51 percent among control hospitals. The relative change was 8 percentage points (95 percent confidence interval: 2-13: p<.001). Our findings suggest that the Breakthrough Collaborative led to an increase in donation rates at participating hospitals.

Beyond the basics. Effects of the Eden Alternative model on quality of life issues.

PubMed

Bergman-Evans, Brenda

2004-06-01

In Life Worth Living, Thomas (1996) proposed that in long-term care facilities for elderly individuals, loneliness, helplessness, and boredom are out of control and are steadily decaying the residents' spirits, adversely affecting quality of life. While Thomas' contention appeals to common sense, no empirical evidence is offered in its support. The purpose of this quasi-experimental study was to assess the impact of implementation of the Eden Alternative model on levels of loneliness, boredom, and helplessness of older residents of a long-term care facility. The model was introduced into the experimental facility on May 1, 1998. The final sample for the experimental group included 21 cognitively intact older adults from a state veterans home (13 men, 8 women, mean age = 76.1). The final control group was composed of 13 residents in a private long-term care facility (11 women, 2 men, mean age = 85.7). A Background Data Sheet, the Geriatric Depression Scale (includes yes or no questions related to helplessness and boredom), and the UCLA Loneliness Scale (Version 3) were administered by an interviewer at baseline and 1-year post-implementation of the Eden Alternative model. Data analysis from the post-implementation phase revealed significant differences between the groups on levels of boredom (z = -2.6, p = .01) and helplessness (z = -2.2, p = .03). Lower levels of distress were found in the experimental group on both boredom and helplessness, but not loneliness. Findings suggest health care professionals and researchers have an opportunity to take a leading role in impacting services related to quality-of-life issues for this important, but often overlooked, population.

A compilation of global bio-optical in situ data for ocean-colour satellite applications

NASA Astrophysics Data System (ADS)

Valente, André; Sathyendranath, Shubha; Brotas, Vanda; Groom, Steve; Grant, Michael; Taberner, Malcolm; Antoine, David; Arnone, Robert; Balch, William M.; Barker, Kathryn; Barlow, Ray; Bélanger, Simon; Berthon, Jean-François; Beşiktepe, Şükrü; Brando, Vittorio; Canuti, Elisabetta; Chavez, Francisco; Claustre, Hervé; Crout, Richard; Frouin, Robert; García-Soto, Carlos; Gibb, Stuart W.; Gould, Richard; Hooker, Stanford; Kahru, Mati; Klein, Holger; Kratzer, Susanne; Loisel, Hubert; McKee, David; Mitchell, Brian G.; Moisan, Tiffany; Muller-Karger, Frank; O'Dowd, Leonie; Ondrusek, Michael; Poulton, Alex J.; Repecaud, Michel; Smyth, Timothy; Sosik, Heidi M.; Twardowski, Michael; Voss, Kenneth; Werdell, Jeremy; Wernand, Marcel; Zibordi, Giuseppe

2016-06-01

A compiled set of in situ data is important to evaluate the quality of ocean-colour satellite-data records. Here we describe the data compiled for the validation of the ocean-colour products from the ESA Ocean Colour Climate Change Initiative (OC-CCI). The data were acquired from several sources (MOBY, BOUSSOLE, AERONET-OC, SeaBASS, NOMAD, MERMAID, AMT, ICES, HOT, GeP&CO), span between 1997 and 2012, and have a global distribution. Observations of the following variables were compiled: spectral remote-sensing reflectances, concentrations of chlorophyll a, spectral inherent optical properties and spectral diffuse attenuation coefficients. The data were from multi-project archives acquired via the open internet services or from individual projects, acquired directly from data providers. Methodologies were implemented for homogenisation, quality control and merging of all data. No changes were made to the original data, other than averaging of observations that were close in time and space, elimination of some points after quality control and conversion to a standard format. The final result is a merged table designed for validation of satellite-derived ocean-colour products and available in text format. Metadata of each in situ measurement (original source, cruise or experiment, principal investigator) were preserved throughout the work and made available in the final table. Using all the data in a validation exercise increases the number of matchups and enhances the representativeness of different marine regimes. By making available the metadata, it is also possible to analyse each set of data separately. The compiled data are available at doi:10.1594/PANGAEA.854832 (Valente et al., 2015).

Case Studies in Modelling, Control in Food Processes.

PubMed

Glassey, J; Barone, A; Montague, G A; Sabou, V

This chapter discusses the importance of modelling and control in increasing food process efficiency and ensuring product quality. Various approaches to both modelling and control in food processing are set in the context of the specific challenges in this industrial sector and latest developments in each area are discussed. Three industrial case studies are used to demonstrate the benefits of advanced measurement, modelling and control in food processes. The first case study illustrates the use of knowledge elicitation from expert operators in the process for the manufacture of potato chips (French fries) and the consequent improvements in process control to increase the consistency of the resulting product. The second case study highlights the economic benefits of tighter control of an important process parameter, moisture content, in potato crisp (chips) manufacture. The final case study describes the use of NIR spectroscopy in ensuring effective mixing of dry multicomponent mixtures and pastes. Practical implementation tips and infrastructure requirements are also discussed.

Characterisation and potential application of pineapple pomace in an extruded product for fibre enhancement.

PubMed

Selani, Miriam Mabel; Brazaca, Solange Guidolin Canniatti; Dos Santos Dias, Carlos Tadeu; Ratnayake, Wajira S; Flores, Rolando A; Bianchini, Andreia

2014-11-15

This study characterised pineapple pomace (PP) and evaluated its application in extrusion to enhance fibre content of the final product. The pomace had low fat (0.61%) and high dietary fibre (45.22%), showing its potential for fibre enrichment of nutritionally poor products, as some extruded snacks. Results also showed low microbiological counts, water activity, and pH indicating good microbiological quality and low risk of physicochemical deterioration. During extrusion, pomace (0%, 10.5% and 21%), moisture (14%, 15% and 16%) and temperature (140 and 160°C) were evaluated. The PP addition decreased expansion and luminosity; while increasing redness of the extrudates compared to the control (0% pomace/14% moisture/140°C). When hardness, yellowness, water absorption, and bulk density were compared to the control, there was no effect (p>0.05) of 10.5% PP addition on the extrudates, indicating that, at this level, PP could be added without affecting the properties of the final extruded product. Copyright © 2014 Elsevier Ltd. All rights reserved.

Influence of Plasma Jet Temperature Profiles in Arc Discharge Methods of Carbon Nanotubes Synthesis

PubMed Central

Raniszewski, Grzegorz; Wiak, Slawomir; Pietrzak, Lukasz; Szymanski, Lukasz; Kolacinski, Zbigniew

2017-01-01

One of the most common methods of carbon nanotubes (CNTs) synthesis is application of an electric-arc plasma. However, the final product in the form of cathode deposit is composed of carbon nanotubes and a variety of carbon impurities. An assay of carbon nanotubes produced in arc discharge systems available on the market shows that commercial cathode deposits contain about 10% CNTs. Given that the quality of the final product depends on carbon–plasma jet parameters, it is possible to increase the yield of the synthesis by plasma jet control. Most of the carbon nanotubes are multiwall carbon nanotubes (MWCNTs). It was observed that the addition of catalysts significantly changes the plasma composition, effective ionization potential, the arc channel conductance, and in effect temperature of the arc and carbon elements flux. This paper focuses on the influence of metal components on plasma-jet forming containing carbon nanotubes cathode deposit. The plasma jet temperature control system is presented. PMID:28336884

Influence of Plasma Jet Temperature Profiles in Arc Discharge Methods of Carbon Nanotubes Synthesis.

PubMed

Raniszewski, Grzegorz; Wiak, Slawomir; Pietrzak, Lukasz; Szymanski, Lukasz; Kolacinski, Zbigniew

2017-02-23

One of the most common methods of carbon nanotubes (CNTs) synthesis is application of an electric-arc plasma. However, the final product in the form of cathode deposit is composed of carbon nanotubes and a variety of carbon impurities. An assay of carbon nanotubes produced in arc discharge systems available on the market shows that commercial cathode deposits contain about 10% CNTs. Given that the quality of the final product depends on carbon-plasma jet parameters, it is possible to increase the yield of the synthesis by plasma jet control. Most of the carbon nanotubes are multiwall carbon nanotubes (MWCNTs). It was observed that the addition of catalysts significantly changes the plasma composition, effective ionization potential, the arc channel conductance, and in effect temperature of the arc and carbon elements flux. This paper focuses on the influence of metal components on plasma-jet forming containing carbon nanotubes cathode deposit. The plasma jet temperature control system is presented.

Easing the transition: the final year of medical education at Maastricht University.

PubMed

van den Akker, Marjan; Dornan, Tim; Scherpbier, Albert J J A; oude Egbrink, Mirjam G A; Snoeckx, Luc H E H

2012-01-01

This manuscript describes the final year of medical education at Maastricht University as it has been operating since 2006. At the time external drivers for the development of a new structure of the final year were: the desire to prepare medical students for lifelong learning, the CanMEDs that were increasingly acknowledged to state the final attainment level of medical education and an increasing recognition of the importance of learning by participating actively and by taking more responsibility. Internal drivers were students' evaluations and our wish to improve instructional design and quality control. The main aim of this new final year is to better prepare students for the transition from the medical master programme to one of the postgraduate training programmes to become a medical specialist. The final year of the medical master programme consists of two 18-weeks participation electives, one in health care and one in research. Students have a higher level of autonomy and responsibility during this final year compared to the preceding medical clerkships to enhance the transition. Portfolios are the key element in examination of SCIP and HELP. Student evaluations of the final year show high scores on coaching and instructiveness. Despite some differences between departments overall scores are very high. Suggestions to improve include the availability of work places and time for education and coaching. Copyright © 2012. Published by Elsevier GmbH.

[Cleaning and disinfection in nursing homes. Data on quality of structure, process and outcome in nursing homes in Frankfurt am Main, Germany, 2011].

PubMed

Heudorf, U; Gasteyer, S; Samoiski, Y; Voigt, K

2012-08-01

Due to the Infectious Disease Prevention Act, public health services in Germany are obliged to check the infection prevention in hospitals and other medical facilities as well as in nursing homes. In Frankfurt/Main, Germany, standardized control visits have been performed for many years. In 2011 focus was laid on cleaning and disinfection of surfaces. All 41 nursing homes were checked according to a standardized checklist covering quality of structure (i.e. staffing, hygiene concept), quality of process (observation of the cleaning processes in the homes) and quality of output, which was monitored by checking the cleaning of fluorescent marks which had been applied some days before and should have been removed via cleaning in the following days before the final check. In more than two thirds of the homes, cleaning personnel were salaried, in one third external personnel were hired. Of the homes 85% provided service clothing and all of them offered protective clothing. All homes had established hygiene and cleaning concepts, however, in 15% of the homes concepts for the handling of Norovirus and in 30% concepts for the handling of Clostridium difficile were missing. Regarding process quality only half of the processes observed, i.e. cleaning of hand contact surfaces, such as handrails, washing areas and bins, were correct. Only 44% of the cleaning controls were correct with enormous differences between the homes (0-100%). The correlation between quality of process and quality of output was significant. There was good quality of structure in the homes but regarding quality of process and outcome there was great need for improvement. This was especially due to faults in communication and coordination between cleaning personnel and nursing personnel. Quality outcome was neither associated with the number of the places for residents nor with staffing. Thus, not only quality of structure but also quality of process and outcome should be checked by the public health services.

Laboratory quality management system: road to accreditation and beyond.

PubMed

Wadhwa, V; Rai, S; Thukral, T; Chopra, M

2012-01-01

This review attempts to clarify the concepts of Laboratory Quality Management System (Lab QMS) for a medical testing and diagnostic laboratory in a holistic way and hopes to expand the horizon beyond quality control (QC) and quality assurance. It provides an insight on accreditation bodies and highlights a glimpse of existing laboratory practices but essentially it takes the reader through the journey of accreditation and during the course of reading and understanding this document, prepares the laboratory for the same. Some of the areas which have not been highlighted previously include: requirement for accreditation consultants, laboratory infrastructure and scope, applying for accreditation, document preparation. This section is well supported with practical illustrations and necessary tables and exhaustive details like preparation of a standard operating procedure and a quality manual. Concept of training and privileging of staff has been clarified and a few of the QC exercises have been dealt with in a novel way. Finally, a practical advice for facing an actual third party assessment and caution needed to prevent post-assessment pitfalls has been dealt with.

An integrated approach to uncover quality marker underlying the effects of Alisma orientale on lipid metabolism, using chemical analysis and network pharmacology.

PubMed

Liao, Maoliang; Shang, Haihua; Li, Yazhuo; Li, Tian; Wang, Miao; Zheng, Yanan; Hou, Wenbin; Liu, Changxiao

2018-06-01

Quality control of traditional Chinese medicines is currently a great concern, due to the correlation between the quality control indicators and clinic effect is often questionable. According to the "multi-components and multi-targets" property of TCMs, a new special quality and bioactivity evaluation system is urgently needed. Present study adopted an integrated approach to provide new insights relating to uncover quality marker underlying the effects of Alisma orientale (AO) on lipid metabolism. In this paper, guided by the concept of the quality marker (Q-marker), an integrated strategies "effect-compound-target-fingerprint" was established to discovery and screen the potential quality marker of AO based on network pharmacology and chemical analysis. Firstly, a bioactivity evaluation was performed to screen the main active fractions. Then the chemical compositions were rapidly identified by chemical analysis. Next, networks were constructed to illuminate the interactions between these component and their targets for lipid metabolism, and the potential Q-marker of AO was initially screened. Finally, the activity of the Q-markers was validated in vitro. 50% ethanol extract fraction was found to have the strongest lipid-lowering activity. Then, the network pharmacology was used to clarify the unique relationship between the Q-markers and their integral pharmacological action. Combined with the results obtained, five active ingredients in the 50% ethanol extract fraction were given special considerations to be representative Q-markers: Alisol A, Alisol B, Alisol A 23-acetate, Alisol B 23-acetate and Alisol A 24-acetate, respectively. The chromatographic fingerprints based Q-marker was establishment. The integrated Q-marker screen may offer an alternative quality assessment of herbal medicines. Copyright © 2018. Published by Elsevier GmbH.

76 FR 48006 - Limited Federal Implementation Plan; Prevention of Significant Deterioration; California; North...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-08

... Implementation Plan; Prevention of Significant Deterioration; California; North Coast Unified Air Quality Management District AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: EPA is finalizing a limited Federal Implementation Plan (FIP) for the North Coast Unified Air Quality Management...

Baselining current road weather information : results of the 2010 quality and importance survey final report.

DOT National Transportation Integrated Search

2011-01-30

This final report contains research findings on the characterization of the quality and value of road weather information resources used by members of the surface transportation community in their decision-making process. This report focuses on the r...

Health related quality of life among myocardial infarction survivors in the United States: a propensity score matched analysis.

PubMed

Mollon, Lea; Bhattacharjee, Sandipan

2017-12-04

Little is known regarding the health-related quality of life among myocardial infarction (MI) survivors in the United States. The purpose of this population-based study was to identify differences in health-related quality of life domains between MI survivors and propensity score matched controls. This retrospective, cross-sectional matched case-control study examined differences in health-related quality of life (HRQoL) among MI survivors of myocardial infarction compared to propensity score matched controls using data from the 2015 Behavioral Risk Factor Surveillance System (BRFSS) survey. Propensity scores were generated via logistic regression for MI survivors and controls based on gender, race/ethnicity, age, body mass index (BMI), smoking status, and comorbidities. Chi-square tests were used to compare differences between MI survivors to controls for demographic variables. A multivariate analysis of HRQoL domains estimated odds ratios. Life satisfaction, sleep quality, and activity limitations were estimated using binary logistic regression. Social support, perceived general health, perceived physical health, and perceived mental health were estimated using multinomial logistic regression. Significance was set at p < 0.05. The final sample consisted of 16,729 MI survivors matched to 50,187 controls (n = 66,916). Survivors were approximately 2.7 times more likely to report fair/poor general health compared to control (AOR = 2.72, 95% CI: 2.43-3.05) and 1.5 times more likely to report limitations to daily activities (AOR = 1.46, 95% CI: 1.34-1.59). Survivors were more likely to report poor physical health >15 days in the month (AOR = 1.63, 95% CI: 1.46-1.83) and poor mental health >15 days in the month (AOR = 1.25, 95% CI: 1.07-1.46) compared to matched controls. There was no difference in survivors compared to controls in level of emotional support (rarely/never: AOR = 0.75, 95% CI: 0.48-1.18; sometimes: AOR = 0.73, 95% CI: 0.41-1.28), hours of recommended sleep (AOR = 1.14, 95% CI: 0.94-1.38), or life satisfaction (AOR = 1.62, 95% CI: 0.99-2.63). MI survivors experienced lower HRQoL on domains of general health, physical health, daily activity, and mental health compared to the general population.

Upgrades to the NOAA/NESDIS automated Cloud-Motion Vector system

NASA Technical Reports Server (NTRS)

Nieman, Steve; Menzel, W. Paul; Hayden, Christopher M.; Wanzong, Steve; Velden, Christopher S.

1993-01-01

The latest version of the automated cloud motion vector software has yielded significant improvements in the quality of the GOES cloud-drift winds produced operationally by NESDIS. Cloud motion vectors resulting from the automated system are now equal or superior in quality to those which had the benefit of manual quality control a few years ago. The single most important factor in this improvement has been the upgraded auto-editor. Improved tracer selection procedures eliminate targets in difficult regions and allow a higher target density and therefore enhanced coverage in areas of interest. The incorporation of the H2O-intercept height assignment method allows an adequate representation of the heights of semi-transparent clouds in the absence of a CO2-absorption channel. Finally, GOES-8 water-vapor motion winds resulting from the automated system are superior to any done previously by NESDIS and should now be considered as an operational product.

Localized analysis of paint-coat drying using dynamic speckle interferometry

NASA Astrophysics Data System (ADS)

Sierra-Sosa, Daniel; Tebaldi, Myrian; Grumel, Eduardo; Rabal, Hector; Elmaghraby, Adel

2018-07-01

The paint-coating is part of several industrial processes, including the automotive industry, architectural coatings, machinery and appliances. These paint-coatings must comply with high quality standards, for this reason evaluation techniques from paint-coatings are in constant development. One important factor from the paint-coating process is the drying, as it has influence on the quality of final results. In this work we present an assessment technique based on the optical dynamic speckle interferometry, this technique allows for the temporal activity evaluation of the paint-coating drying process, providing localized information from drying. This localized information is relevant in order to address the drying homogeneity, optimal drying, and quality control. The technique relies in the definition of a new temporal history of the speckle patterns to obtain the local activity; this information is then clustered to provide a convenient indicative of different drying process stages. The experimental results presented were validated using the gravimetric drying curves

Traditional and emerging forms of dental practice. Cost, accessibility, and quality factors.

PubMed Central

Rovin, S; Nash, J

1982-01-01

The traditional and predominant manner of delivering dental care is through a fee-for-service, private practice system. A number of alternative dental care delivery systems have emerged and are being tested, and others are just emerging. These systems include department store practices, hospital dental services, health maintenance organizations, the independent practice of dental hygiene, and denturism. Although it is too soon to draw final conclusions about the efficacy and effectiveness of these systems, we examine them for their potential to compete with and change the way dental care is currently delivered. Using the parameters of cost, accessibility, and quality, we compare these systems to traditional dental practice. Some of these emerging forms clearly have the potential to complete favorably with traditional practice. Other seem less likely to alter the existing system substantially. The system which can best control costs, increase accessibility, and enhance quality will gain the competitive edge. PMID:7091453

User Access Management Based on Network Pricing for Social Network Applications

PubMed Central

Ma, Xingmin; Gu, Qing

2018-01-01

Social applications play a very important role in people’s lives, as users communicate with each other through social networks on a daily basis. This presents a challenge: How does one receive high-quality service from social networks at a low cost? Users can access different kinds of wireless networks from various locations. This paper proposes a user access management strategy based on network pricing such that networks can increase its income and improve service quality. Firstly, network price is treated as an optimizing access parameter, and an unascertained membership algorithm is used to make pricing decisions. Secondly, network price is adjusted dynamically in real time according to network load. Finally, selecting a network is managed and controlled in terms of the market economy. Simulation results show that the proposed scheme can effectively balance network load, reduce network congestion, improve the user's quality of service (QoS) requirements, and increase the network’s income. PMID:29495252

WELDSMART: A vision-based expert system for quality control

NASA Technical Reports Server (NTRS)

Andersen, Kristinn; Barnett, Robert Joel; Springfield, James F.; Cook, George E.

1992-01-01

This work was aimed at exploring means for utilizing computer technology in quality inspection and evaluation. Inspection of metallic welds was selected as the main application for this development and primary emphasis was placed on visual inspection, as opposed to other inspection methods, such as radiographic techniques. Emphasis was placed on methodologies with the potential for use in real-time quality control systems. Because quality evaluation is somewhat subjective, despite various efforts to classify discontinuities and standardize inspection methods, the task of using a computer for both inspection and evaluation was not trivial. The work started out with a review of the various inspection techniques that are used for quality control in welding. Among other observations from this review was the finding that most weld defects result in abnormalities that may be seen by visual inspection. This supports the approach of emphasizing visual inspection for this work. Quality control consists of two phases: (1) identification of weld discontinuities (some of which may be severe enough to be classified as defects), and (2) assessment or evaluation of the weld based on the observed discontinuities. Usually the latter phase results in a pass/fail judgement for the inspected piece. It is the conclusion of this work that the first of the above tasks, identification of discontinuities, is the most challenging one. It calls for sophisticated image processing and image analysis techniques, and frequently ad hoc methods have to be developed to identify specific features in the weld image. The difficulty of this task is generally not due to limited computing power. In most cases it was found that a modest personal computer or workstation could carry out most computations in a reasonably short time period. Rather, the algorithms and methods necessary for identifying weld discontinuities were in some cases limited. The fact that specific techniques were finally developed and successfully demosntrated to work illustrates that the general approach taken here appears to be promising for commercial development of computerized quality inspection systems. Inspection based on these techniques may be used to supplement or substitute more elaborate inspection methods, such as x-ray inspections.

Effects of feeding distillers dried grains with solubles, high-protein distillers dried grains, and corn germ to growing-finishing pigs on pig performance, carcass quality, and the palatability of pork.

PubMed

Widmer, M R; McGinnis, L M; Wulf, D M; Stein, H H

2008-08-01

An experiment was conducted to investigate pig performance, carcass quality, and palatability of pork from pigs fed distillers dried grains with solubles (DDGS), high-protein distillers dried grains (HPDDG), and corn germ. Eighty-four pigs (initial BW, 22 +/- 1.7 kg) were allotted to 7 dietary treatments with 6 replicates per treatment and 2 pigs per pen. Diets were fed for 114 d in a 3-phase program. The control treatment was based on corn and soybean meal. Two treatments were formulated using 10 or 20% DDGS in each phase. Two additional treatments contained HP-DDG in amounts sufficient to substitute for either 50 or 100% of the soybean meal used in the control treatment. An additional 2 treatments contained 5 or 10% corn germ, which was calculated to provide the same amount of fat as 10 or 20% DDGS. Results showed that for the entire experiment, pig performance was not affected by DDGS or HP-DDG, but final BW increased (linear, P < 0.05) as corn germ was included in the diets. Carcass composition and muscle quality were not affected by DDGS, but LM area and LM depth decreased (linear, P < 0.05) as HP-DDG was added to the diets. Lean meat percentage increased and drip loss decreased as corn germ was included in the diets (quadratic, P < 0.05). There was no effect of DDGS on fat quality except that belly firmness decreased (linear, P < 0.05) as dietary DDGS concentration increased. Including HP-DDG or corn germ in the diets did not affect fat quality, except that the iodine value increased (linear, P < 0.05) in pigs fed HP-DDG diets and decreased (linear, P < 0.05) in pigs fed corn germ diets. Cooking loss, shear force, and bacon distortion score were not affected by the inclusion of DDGS, HP-DDG, or corn germ in the diets, and the overall palatability of the bacon and pork chops was not affected by dietary treatment. In conclusion, feeding 20% DDGS or high levels of HP-DDG to growing-finishing pigs did not negatively affect overall pig performance, carcass composition, muscle quality, or palatability but may decrease fat quality. Feeding up to 10% corn germ did not negatively affect pig performance, carcass composition, carcass quality, or pork palatability but increased final BW of the pigs and reduced the iodine value of belly fat.

Advances and Best Practices in Airborne Gravimetry from the U.S. GRAV-D Project

NASA Astrophysics Data System (ADS)

Diehl, Theresa; Childers, Vicki; Preaux, Sandra; Holmes, Simon; Weil, Carly

2013-04-01

The Gravity for the Redefinition of the American Vertical Datum (GRAV-D) project, an official policy of the U.S. National Geodetic Survey as of 2007, is working to survey the entire U.S. and its holdings with high-altitude airborne gravimetry. The goal of the project is to provide a consistent, high-quality gravity dataset that will become the cornerstone of a new gravimetric geoid and national vertical datum in 2022. Over the last five years, the GRAV-D project has surveyed more than 25% of the country, accomplishing almost 500 flights on six different aircraft platforms and producing more than 3.7 Million square km of data thus far. This wealth of experience has led to advances in the collection, processing, and evaluation of high-altitude (20,000 - 35,000 ft) airborne gravity data. This presentation will highlight the most important practical and theoretical advances of the GRAV-D project, giving an introduction to each. Examples of innovation include: 1. Use of navigation grade inertial measurement unit data and precise lever arm measurements for positioning; 2. New quality control tests and software for near real-time analysis of data in the field; 3. Increased accuracy of gravity post-processing by reexamining assumptions and simplifications that were inconsistent with a goal of 1 mGal precision; and 4. Better final data evaluation through crossovers, additional statistics, and inclusion of airborne data into harmonic models that use EGM08 as a base model. The increases in data quality that resulted from implementation of the above advances (and others) will be shown with a case study of the GRAV-D 2008 southern Alaska survey near Anchorage, over Cook Inlet. The case study's statistics and comparisons to global models illustrate the impact that these advances have had on the final airborne gravity data quality. Finally, the presentation will summarize the best practices identified by the project from its last five years of experience.

75 FR 34669 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Transportation...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-18

... Promulgation of Air Quality Implementation Plans; Maryland; Transportation Conformity Regulations AGENCY... Implementation Plan (SIP) revision submitted by Maryland for Transportation Conformity Regulations. In the Final Rules section of this Federal Register, EPA is approving the State's SIP submittal as a direct final...

SeaWiFS Technical Report Series. Volume 38; SeaWiFS Calibration and Validation Quality Control Procedures

NASA Technical Reports Server (NTRS)

Hooker, Stanford B. (Editor); Firestone, Elaine R. (Editor); McClain, Charles R.; Darzi, Michael; Barnes, Robert A.; Eplee, Robert E.; Firestone, James K.; Patt, Frederick S.; Robinson, Wayne D.; Schieber, Brian D.;

Psychosocial Characteristics of Children with Central Disorders of Hypersomnolence Versus Matched Healthy Children

PubMed Central

Avis, Kristin T.; Shen, Jiabin; Weaver, Patrick; Schwebel, David C.

2015-01-01

Background: Hypersomnia of central origin from narcolepsy or idiopathic hypersomnia (IHS) is characterized by pathological levels of excessive daytime sleepiness (EDS). Central hypersomnia has historically been underdiagnosed and poorly understood, especially with respect to its impact on daytime functioning and quality of life in children. Objective: Describe the psychosocial adjustment of children treated for narcolepsy or IHS on school performance, quality of life, and physical/extracurricular activities. Methods: Using a matched case control design, we compared child self- and parent-reported data from thirty-three 8- to 16-year-olds with an established diagnosis of narcolepsy or IHS, according to ICSD-2 criteria, to that of 33 healthy children matched by age, race/ethnicity, gender, and household income. Assessments evaluated academic performance, quality of life and wellness, sleepiness, and participation in extracurricular activities. Results: Compared to healthy controls, children with central hypersomnia had poorer daytime functioning in multiple domains. Children with hypersomnia missed more days of school and had lower grades than healthy controls. Children with hypersomnia had poorer quality of life by both parent and child report. Children with hypersomnia were significantly sleepier, had higher BMI, and were more likely to report a history of recent injury. Finally, children with hypersomnia engaged in fewer after-school activities than healthy controls. Conclusions: A range of significant psychosocial consequences are reported in children with hypersomnia even after a diagnosis has been made and treatments initiated. Health care professionals should be mindful of the psychosocial problems that may present in children with hypersomnia over the course of treatment. Citation: Avis KT, Shen J, Weaver P, Schwebel DC. Psychosocial characteristics of children with central disorders of hypersomnolence versus matched healthy children. J Clin Sleep Med 2015;11(11):1281–1288. PMID:26285115

Application of Advanced Process Control techniques to a pusher type reheating furnace

NASA Astrophysics Data System (ADS)

Zanoli, S. M.; Pepe, C.; Barboni, L.

2015-11-01

In this paper an Advanced Process Control system aimed at controlling and optimizing a pusher type reheating furnace located in an Italian steel plant is proposed. The designed controller replaced the previous control system, based on PID controllers manually conducted by process operators. A two-layer Model Predictive Control architecture has been adopted that, exploiting a chemical, physical and economic modelling of the process, overcomes the limitations of plant operators’ mental model and knowledge. In addition, an ad hoc decoupling strategy has been implemented, allowing the selection of the manipulated variables to be used for the control of each single process variable. Finally, in order to improve the system flexibility and resilience, the controller has been equipped with a supervision module. A profitable trade-off between conflicting specifications, e.g. safety, quality and production constraints, energy saving and pollution impact, has been guaranteed. Simulation tests and real plant results demonstrated the soundness and the reliability of the proposed system.

National continuous surveys on internal quality control for HbA1c in 306 clinical laboratories of China from 2012 to 2016: Continual improvement.

PubMed

Li, Tingting; Wang, Wei; Zhao, Haijian; He, Falin; Zhong, Kun; Yuan, Shuai; Wang, Zhiguo

2017-09-01

This study aimed to evaluate whether the quality performance of clinical laboratories in China has been greatly improved and whether Internal Quality Control (IQC) practice of HbA1c has also been changed since National Center for Clinical Laboratories (NCCL) of China organized laboratories to report IQC data for HbA1c in 2012. Internal Quality Control information of 306 External Quality Assessment (EQA) participant laboratories which kept reporting IQC data in February from 2012 to 2016 were collected by Web-based EQA system. Then percentages of laboratories meeting four different imprecision specifications for current coefficient of variations (CVs) of HbA1c measurements were calculated. Finally, we comprehensively analyzed analytical systems and IQC practice of HbA1c measurements. The current CVs of HbA1c tests have decreased significantly from 2012 to 2016. And percentages of laboratories meeting four imprecision specifications for CVs all showed the increasing tendency year by year. As for analytical system, 52.1% (159/306) laboratories changed their systems with the change in principle of assay. And many laboratories began to use cation exchange high-performance liquid chromatography (CE-HPLC) instead of Immunoturbidimetry, because CE-HPLC owed a lower intra-laboratory CVs. The data of IQC practice, such as IQC rules and frequency, also showed significant variability among years with overall tendency of meeting requirements. The imprecision performance of HbA1c tests has been improved in these 5 years with the change in IQC practice, but it is still disappointing in China. Therefore, laboratories should actively find existing problems and take action to promote performance of HbA1c measurements. © 2016 Wiley Periodicals, Inc.

Effect of probiotics and thyme essential oil on the essential amino acid content of the broiler chicken meat.

PubMed

Alfaig, Ebrahim; Angelovičova, Maria; Kral, Martin; Bučko, Ondrej

2014-01-01

Differences in the types and percentages of essential amino acids (EAAs) in food could influence the value of protein consumed and proteins with a high content of EAAs are the most important components of poultry meat. The use of probiotics for meat and carcass quality improvement has been questioned, while feed supplementation with thyme essential oil (TEO) could be considered as useful natural supplement to be applied in the poultry industry to improve meat quality. Day-old broilers Ross 308 (n = 400) were randomly divided into four groups based on the feed supplement as follows: control, probiotics 0.05%, TEO 0.05% and combination of probiotics and TEO, while the fattening period was 42 days. Six birds of both sexes from each group were selected as a sample, slaughtered and then stored (-18°C) for 6 months till the analysis. The muscular homogeneous sample (50 g) from the breast and thigh of each sample bird was analysed by the Fourier Transform Infrared Spectroscopy method using the device Nicolet 6700. The essential amino acids content was determined and the quality indicators include chemical score, amino acid score, EAA index and biological value were calculated. The obtained results show that for all the tested EAAs of the breast and thigh muscles, the content numerically increased gradually and progressively within the groups as the control scored the minimum followed by the probiotics group, then the combination group and finally the TEO group which scored the highest results. It can be concluded that the TEO promoted the increase of all the EAAs and consequently the quality indicators with significant different compared with the control group and significantly different for some EAAs and quality indicators compared with the probiotics group and the combination group.

Implementation of Cyber-Physical Production Systems for Quality Prediction and Operation Control in Metal Casting

PubMed Central

Lee, JuneHyuck; Noh, Sang Do; Kim, Hyun-Jung; Kang, Yong-Shin

2018-01-01

The prediction of internal defects of metal casting immediately after the casting process saves unnecessary time and money by reducing the amount of inputs into the next stage, such as the machining process, and enables flexible scheduling. Cyber-physical production systems (CPPS) perfectly fulfill the aforementioned requirements. This study deals with the implementation of CPPS in a real factory to predict the quality of metal casting and operation control. First, a CPPS architecture framework for quality prediction and operation control in metal-casting production was designed. The framework describes collaboration among internet of things (IoT), artificial intelligence, simulations, manufacturing execution systems, and advanced planning and scheduling systems. Subsequently, the implementation of the CPPS in actual plants is described. Temperature is a major factor that affects casting quality, and thus, temperature sensors and IoT communication devices were attached to casting machines. The well-known NoSQL database, HBase and the high-speed processing/analysis tool, Spark, are used for IoT repository and data pre-processing, respectively. Many machine learning algorithms such as decision tree, random forest, artificial neural network, and support vector machine were used for quality prediction and compared with R software. Finally, the operation of the entire system is demonstrated through a CPPS dashboard. In an era in which most CPPS-related studies are conducted on high-level abstract models, this study describes more specific architectural frameworks, use cases, usable software, and analytical methodologies. In addition, this study verifies the usefulness of CPPS by estimating quantitative effects. This is expected to contribute to the proliferation of CPPS in the industry. PMID:29734699

THE LONG-TERM EFFICACY OF ACUTE-PHASE PSYCHOTHERAPY FOR DEPRESSION: A META-ANALYSIS OF RANDOMIZED TRIALS.

PubMed

Karyotaki, Eirini; Smit, Yolba; de Beurs, Derek P; Henningsen, Kirsten Holdt; Robays, Jo; Huibers, Marcus J H; Weitz, Erica; Cuijpers, Pim

2016-05-01

Understanding the effectiveness of treatment for depression in both the short term and long term is essential for clinical decision making. The present meta-analysis examined treatment effects on depression and quality of life in acute-phase psychotherapeutic interventions compared to no treatment control groups for adult depression at 6 months or longer postrandomization. A systematic literature search resulted in 44 randomized controlled trials with 6,096 participants. Acute-phase psychotherapy was compared to control groups at 6-month or longer postrandomization. Odds ratios of a positive outcome were calculated. Psychotherapy outperformed control groups at 6 months or longer postrandomization (OR = 1.92, 95% CI: 1.60-2.31, P < .001). Heterogeneity was moderate (I²: 65, 95% CI: 53-74, P < .001). However, effects significantly decreased with longer follow-up periods. Additionally, a small positive effect of psychotherapy was observed for quality of life, while similar effects were obtained in separate analyses of each type of psychotherapy, with the exception of nondirective supportive therapy. Studies that provided booster sessions had better treatment results compared with studies that did not provide any further sessions. Finally, we found that trials on psychotherapy aimed at major depressive disorder (MDD) had better outcomes than those that were aimed at elevated depressive symptoms. There is substantial evidence that acute-phase psychotherapy results in a better treatment effects on depression and quality of life in the long term for adult patients with depression. © 2016 Wiley Periodicals, Inc.

Air Pollution Prevention and Control Policy in China.

PubMed

Huang, Cunrui; Wang, Qiong; Wang, Suhan; Ren, Meng; Ma, Rui; He, Yiling

2017-01-01

With rapid urbanization and development of transport infrastructure, air pollution caused by multiple-pollutant emissions and vehicle exhaust has been aggravated year by year in China. In order to improve air quality, the Chinese authorities have taken a series of actions to control air pollution emission load within a permissible range. However, although China has made positive progress on tackling air pollution, these actions have not kept up with its economy growth and fossil-fuel use. The traditional single-pollutant approach is far from enough in China now, and in the near future, air pollution control strategies should move in the direction of the multiple-pollutant approach. In addition, undesirable air quality is usually linked with the combination of high emissions and adverse weather conditions. However, few studies have been done on the influence of climate change on atmospheric chemistry in the global perspective. Available evidence suggested that climate change is likely to exacerbate certain kinds of air pollutants including ozone and smoke from wildfires. This has become a major public health problem because the interactions of global climate change, urban heat islands, and air pollution have adverse effects on human health. In this chapter, we first review the past and current circumstances of China's responses to air pollution. Then we discuss the control challenges and future options for a better air quality in China. Finally, we begin to unravel links between air pollution and climate change, providing new opportunities for integrated research and actions in China.

Enhanced Androgen Signaling with Androgen Receptor Overexpression in the Osteoblast Lineage Controls Skeletal Turnover, Matrix Quality and Bone Architecture

DTIC Science & Technology

2009-12-01

calculatedbyconverting thegrayscale output of bone voxels in Hounsfield units (HU) to mineral values (mg/cc of HA) through the use of a calibration phantom...NUMBER Kristine M. Wiren, Ph.D. 5e. TASK NUMBER E-Mail: wirenk@ohsu.edu 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES...and d) characterization of effects of androgen on MSC colony forming units and lineage commitment in vitro. In this final report, we have included

Development and validation of chromatographic methods (HPLC and GC) for the determination of the active components (benzocaine, tyrothricin and menthol) of a pharmaceutical preparation.

PubMed

Ortiz-Boyer, F; Tena, M T; Luque de Castro, M D; Valcárcel, M

1995-10-01

Methods are reported for the determination of tyrothricin and benzocaine by HPLC and menthol by GC in the analysis of throat lozenges (tablets) containing all three compounds. After optimization of the variables involved in both HPLC and GC the methods have been characterized and validated according to the guidelines of the Spanish Pharmacopoeia, and applied to both the monitoring of the manufacturing process and the quality control of the final product.

USAF Summer Research Program - 1995 Summer Faculty Research Program Final Reports, Volume 5A, Wright Laboratory

DTIC Science & Technology

1995-12-01

Certification. Oliver Wight Publications, Inc. Essex Junction. 1993. Ishikawa , Kaoru . (Translation by David J. Lu) What is Total Quality Control? The Japanese...approximation to the eight-harness satin weave (8H SW) is made, following the mosaic model ( Ishikawa and Chou, 1983) which treats woven composites as cross...K. W. and Bailey, J. E. (1978) Journal of Material Science, Vol. 13, pp. 195. Ishikawa , T. and Chou, T. W. (1983) One-dimensional micromechanical

Consequences of electroplated targets on radiopharmaceutical preparations

NASA Astrophysics Data System (ADS)

Finn, R. D.; Tirelli, S.; Sheh, Y.; Knott, A.; Gelbard, A. S.; Larson, S. M.; Dahl, J. R.

1991-05-01

The staff of the cyclotron facility at Memorial Sloan-Kettering Cancer Center is involved in a comprehensive radionuclide preparation program which culminates with the formulation of numerous requested short-lived, positron-emitting radiopharmaceutical agents for clinical investigation. Both the produced radionuclide as well as the final radiolabeled compound are subjected to stringent quality control standards including assays for radiochemical and chemical purity. The subtle chemical consequences resulting from the irradiation of a nickel-plated target for 13N production serve to emphasize some of these potential technical difficulties.

Managing laboratory automation

PubMed Central

Saboe, Thomas J.

1995-01-01

This paper discusses the process of managing automated systems through their life cycles within the quality-control (QC) laboratory environment. The focus is on the process of directing and managing the evolving automation of a laboratory; system examples are given. The author shows how both task and data systems have evolved, and how they interrelate. A BIG picture, or continuum view, is presented and some of the reasons for success or failure of the various examples cited are explored. Finally, some comments on future automation need are discussed. PMID:18925018

The microbiology of malting and brewing.

PubMed

Bokulich, Nicholas A; Bamforth, Charles W

2013-06-01

Brewing beer involves microbial activity at every stage, from raw material production and malting to stability in the package. Most of these activities are desirable, as beer is the result of a traditional food fermentation, but others represent threats to the quality of the final product and must be controlled actively through careful management, the daily task of maltsters and brewers globally. This review collates current knowledge relevant to the biology of brewing yeast, fermentation management, and the microbial ecology of beer and brewing.

The Microbiology of Malting and Brewing

PubMed Central

Bokulich, Nicholas A.

2013-01-01

SUMMARY Brewing beer involves microbial activity at every stage, from raw material production and malting to stability in the package. Most of these activities are desirable, as beer is the result of a traditional food fermentation, but others represent threats to the quality of the final product and must be controlled actively through careful management, the daily task of maltsters and brewers globally. This review collates current knowledge relevant to the biology of brewing yeast, fermentation management, and the microbial ecology of beer and brewing. PMID:23699253

Managing laboratory automation.

PubMed

Saboe, T J

1995-01-01

This paper discusses the process of managing automated systems through their life cycles within the quality-control (QC) laboratory environment. The focus is on the process of directing and managing the evolving automation of a laboratory; system examples are given. The author shows how both task and data systems have evolved, and how they interrelate. A BIG picture, or continuum view, is presented and some of the reasons for success or failure of the various examples cited are explored. Finally, some comments on future automation need are discussed.

Quality control of the tribological coating PS212

NASA Technical Reports Server (NTRS)

Sliney, Harold E.; Dellacorte, Christopher; Deadmore, Daniel L.

1989-01-01

PS212 is a self-lubricating, composite coating that is applied by the plasma spray process. It is a functional lubricating coating from 25 C (or lower) to 900 C. The coating is prepared from a blend of three different powders with very dissimilar properties. Therefore, the final chemical composition and lubricating effectiveness of the coatings are very sensitive to the process variables used in their preparation. Defined here are the relevant variables. The process and analytical procedures that will result in satisfactory tribological coatings are discussed.

Enhanced Androgen Signaling with Androgen Receptor Overexpression in the Osteoblast Lineage Controls Skeletal Turnover, Matrix Quality, and Bone Architecture

DTIC Science & Technology

2005-12-01

the BMD of female-to-male transsexuals treated with ‘male’ levels of testosterone increased to normal male levels at cortical sites [35]. Finally, men...Testosterone increases bone mineral density in female-to- male transsexuals : a case series of 15 subjects.Clin Endocrinol (Oxf) 2004, 61:560-566. 35...Ruetsche A, Kneubuehl R, Birkhaeuser M, Lippuner K: Cortical and trabecular bone mineral density in transsexuals after long-term cross-sex hormonal treatment

Concept for estimating mitochondrial DNA haplogroups using a maximum likelihood approach (EMMA)☆

PubMed Central

Röck, Alexander W.; Dür, Arne; van Oven, Mannis; Parson, Walther

2013-01-01

The assignment of haplogroups to mitochondrial DNA haplotypes contributes substantial value for quality control, not only in forensic genetics but also in population and medical genetics. The availability of Phylotree, a widely accepted phylogenetic tree of human mitochondrial DNA lineages, led to the development of several (semi-)automated software solutions for haplogrouping. However, currently existing haplogrouping tools only make use of haplogroup-defining mutations, whereas private mutations (beyond the haplogroup level) can be additionally informative allowing for enhanced haplogroup assignment. This is especially relevant in the case of (partial) control region sequences, which are mainly used in forensics. The present study makes three major contributions toward a more reliable, semi-automated estimation of mitochondrial haplogroups. First, a quality-controlled database consisting of 14,990 full mtGenomes downloaded from GenBank was compiled. Together with Phylotree, these mtGenomes serve as a reference database for haplogroup estimates. Second, the concept of fluctuation rates, i.e. a maximum likelihood estimation of the stability of mutations based on 19,171 full control region haplotypes for which raw lane data is available, is presented. Finally, an algorithm for estimating the haplogroup of an mtDNA sequence based on the combined database of full mtGenomes and Phylotree, which also incorporates the empirically determined fluctuation rates, is brought forward. On the basis of examples from the literature and EMPOP, the algorithm is not only validated, but both the strength of this approach and its utility for quality control of mitochondrial haplotypes is also demonstrated. PMID:23948335

Image analysis for maintenance of coating quality in nickel electroplating baths--real time control.

PubMed

Vidal, M; Amigo, J M; Bro, R; van den Berg, F; Ostra, M; Ubide, C

2011-11-07

The aim of this paper is to show how it is possible to extract analytical information from images acquired with a flatbed scanner and make use of this information for real time control of a nickel plating process. Digital images of plated steel sheets in a nickel bath are used to follow the process under degradation of specific additives. Dedicated software has been developed for making the obtained results accessible to process operators. This includes obtaining the RGB image, to select the red channel data exclusively, to calculate the histogram of the red channel data and to calculate the mean colour value (MCV) and the standard deviation of the red channel data. MCV is then used by the software to determine the concentration of the additives Supreme Plus Brightner (SPB) and SA-1 (for confidentiality reasons, the chemical contents cannot be further detailed) present in the bath (these two additives degrade and their concentration changes during the process). Finally, the software informs the operator when the bath is generating unsuitable quality plating and suggests the amount of SPB and SA-1 to be added in order to recover the original plating quality. Copyright © 2011 Elsevier B.V. All rights reserved.

Development and characterization of a scintillating cell imaging dish for radioluminescence microscopy.

PubMed

Sengupta, Debanti; Kim, Tae Jin; Almasi, Sepideh; Miller, Stuart; Marton, Zsolt; Nagarkar, Vivek; Pratx, Guillem

2018-04-16

Radioluminescence microscopy is an emerging modality that can be used to image radionuclide probes with micron-scale resolution. This technique is particularly useful as a way to probe the metabolic behavior of single cells and to screen and characterize radiopharmaceuticals, but the quality of the images is critically dependent on the scintillator material used to image the cells. In this paper, we detail the development of a microscopy dish made of a thin-film scintillating material, Lu2O3:Eu, that could be used as the blueprint for a future consumable product. After developing a simple quality control method based on long-lived alpha and beta sources, we characterize the radioluminescence properties of various thin-film scintillator samples. We find consistent performance for most samples, but also identify a few samples that do not meet the specifications, thus stressing the need for routine quality control prior to biological experiments. In addition, we test and quantify the transparency of the material, and demonstrate that transparency correlates with thickness. Finally, we evaluate the biocompatibility of the material and show that the microscopy dish can produce radioluminescent images of live single cells.

Quality control of fifteen probiotic products containing Saccharomyces boulardii.

PubMed

Vanhee, L M E; Goemé, F; Nelis, H J; Coenye, T

2010-11-01

The yeast Saccharomyces boulardii is used as a probiotic for the prevention and treatment of diarrhoea. In this study, the quality of 15 probiotic products containing S. boulardii was verified. Using microsatellite typing, the identity of all Saccharomyces strains in the products was confirmed as S. boulardii. Additionally, solid-phase cytometry (SPC) and a plate method were used to enumerate S. boulardii cells. SPC was not only able to produce results more rapidly than plating (4h compared to 48h) but the cell counts obtained with SPC were significantly higher than the plate counts. Finally, we found that <1% of the S. boulardii cells survived 120min in gastric conditions and storage for 3months at 40°C with 75% relative humidity. We developed a SPC method for the quantification of viable S. boulardii cells in probiotics. Additionally, we demonstrated that gastric conditions and storage have a marked effect on the viability of the yeast cells.   To our knowledge, this is the first time SPC is used for the quality control of probiotics with S. boulardii. Additionally, we demonstrated the need for gastric protection and accurate storage. © 2010 The Authors. Journal of Applied Microbiology © 2010 The Society for Applied Microbiology.

Chemometric applications to assess quality and critical parameters of virgin and extra-virgin olive oil. A review.

PubMed

Gómez-Caravaca, Ana M; Maggio, Rubén M; Cerretani, Lorenzo

2016-03-24

Today virgin and extra-virgin olive oil (VOO and EVOO) are food with a large number of analytical tests planned to ensure its quality and genuineness. Almost all official methods demand high use of reagents and manpower. Because of that, analytical development in this area is continuously evolving. Therefore, this review focuses on analytical methods for EVOO/VOO which use fast and smart approaches based on chemometric techniques in order to reduce time of analysis, reagent consumption, high cost equipment and manpower. Experimental approaches of chemometrics coupled with fast analytical techniques such as UV-Vis spectroscopy, fluorescence, vibrational spectroscopies (NIR, MIR and Raman fluorescence), NMR spectroscopy, and other more complex techniques like chromatography, calorimetry and electrochemical techniques applied to EVOO/VOO production and analysis have been discussed throughout this work. The advantages and drawbacks of this association have also been highlighted. Chemometrics has been evidenced as a powerful tool for the oil industry. In fact, it has been shown how chemometrics can be implemented all along the different steps of EVOO/VOO production: raw material input control, monitoring during process and quality control of final product. Copyright © 2016 Elsevier B.V. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holladay, S.K.; Anderson, H.M.; Benson, S.B.

Quality assurance (QA) objectives for Phase 2 were that (1) scientific data generated would withstand scientific and legal scrutiny; (2) data would be gathered using appropriate procedures for sample collection, sample handling and security, chain of custody, laboratory analyses, and data reporting; (3) data would be of known precision and accuracy; and (4) data would meet data quality objectives defined in the Phase 2 Sampling and Analysis Plan. A review of the QA systems and quality control (QC) data associated with the Phase 2 investigation is presented to evaluate whether the data were of sufficient quality to satisfy Phase 2more » objectives. The data quality indicators of precision, accuracy, representativeness, comparability, completeness, and sensitivity were evaluated to determine any limitations associated with the data. Data were flagged with qualifiers that were associated with appropriate reason codes and documentation relating the qualifiers to the reviewer of the data. These qualifiers were then consolidated into an overall final qualifier to represent the quality of the data to the end user. In summary, reproducible, precise, and accurate measurements consistent with CRRI objectives and the limitations of the sampling and analytical procedures used were obtained for the data collected in support of the Phase 2 Remedial Investigation.« less

Guidelines to reach high-quality purified recombinant proteins.

PubMed

Oliveira, Carla; Domingues, Lucília

2018-01-01

The final goal in recombinant protein production is to obtain high-quality pure protein samples. Indeed, the successful downstream application of a recombinant protein depends on its quality. Besides production, which is conditioned by the host, the quality of a recombinant protein product relies mainly on the purification procedure. Thus, the purification strategy must be carefully designed from the molecular level. On the other hand, the quality control of a protein sample must be performed to ensure its purity, homogeneity and structural conformity, in order to validate the recombinant production and purification process. Therefore, this review aims at providing succinct information on the rational purification design of recombinant proteins produced in Escherichia coli, specifically the tagging purification, as well as on accessible tools for evaluating and optimizing protein quality. The classical techniques for structural protein characterization-denaturing protein gel electrophoresis (SDS-PAGE), size exclusion chromatography (SEC), dynamic light scattering (DLS) and circular dichroism (CD)-are revisited with focus on the protein and their main advantages and disadvantages. Furthermore, methods for determining protein concentration and protein storage are also presented. The guidelines compiled herein will aid preparing pure, soluble and homogeneous functional recombinant proteins from the very beginning of the molecular cloning design.

Identifying models of delivery, care domains and quality indicators relevant to palliative day services: a scoping review protocol.

PubMed

O'Connor, Seán R; Dempster, Martin; McCorry, Noleen K

2017-05-16

With an ageing population and increasing numbers of people with life-limiting illness, there is a growing demand for palliative day services. There is a need to measure and demonstrate the quality of these services, but there is currently little agreement on which aspects of care should be used to do this. The aim of the scoping review will be to map the extent, range and nature of the evidence around models of delivery, care domains and existing quality indicators used to evaluate palliative day services. Electronic databases (MEDLINE, EMBASE, CINAHL, PsycINFO, Cochrane Central Register of Controlled Trials) will be searched for evidence using consensus development methods; randomised or quasi-randomised controlled trials; mixed methods; and prospective, longitudinal or retrospective case-control studies to develop or test quality indicators for evaluating palliative care within non-residential settings, including day hospices and community or primary care settings. At least two researchers will independently conduct all searches, study selection and data abstraction procedures. Meta-analyses and statistical methods of synthesis are not planned as part of the review. Results will be reported using numerical counts, including number of indicators in each care domain and by using qualitative approach to describe important indicator characteristics. A conceptual model will also be developed to summarise the impact of different aspects of quality in a palliative day service context. Methodological quality relating to indicator development will be assessed using the Appraisal of Indicators through Research and Evaluation (AIRE) tool. Overall strength of evidence will be assessed using the Grading of Recommendations, Assessment, Development, and Evaluation (GRADE) system. Final decisions on quality assessment will be made via consensus between review authors. Identifying, developing and implementing evidence-based quality indicators is critical to the evaluation and continued improvement of palliative care. Review findings will be used to support clinicians and policymakers make decisions on which quality indicators are most appropriate for evaluating day services at the patient and service level, and to identify areas for further research.

Coparenting Quality During the First Three Months After Birth: The Role of Infant Sleep Quality

PubMed Central

McDaniel, Brandon T.; Teti, Douglas M.

2013-01-01

The transition to parenthood can be stressful for new parents, as parents must learn to take on new roles and responsibilities. Sleep disruption—which has been linked in prior research to parent distress and fatigue—is common in the early months. The current study is the first to our knowledge to examine infant sleep and its potential indirect influence on parents’ perceptions of coparenting quality at 1 and 3 months of infant age. Participants included 150 families. Mothers reported more night waking, poorer sleep quality, more depressive symptoms, and worse perceptions of coparenting quality as compared with fathers. We tested a structural model of infant and parent night waking and sleep quality as predictors of parent distress and coparenting using maximum likelihood estimation. The frequency of infant night waking predicted father and mother night waking, which in turn predicted parent sleep quality. Poor parent sleep quality predicted elevated depressive symptoms, and finally depressive symptoms were negatively related to perceptions of coparenting quality. Significant indirect effects between infant night waking and parent depression and coparenting quality were found. In summary, both mothers’ and fathers’ perceptions of coparenting were related to the unfolding parental dynamics that take place surrounding infant sleep difficulties. This held true even after controlling for parent education, family income, and infant temperament. Therefore, parenting may indirectly benefit from interventions targeting infant sleep difficulties. PMID:23244456

Accessing groundwater quality in lower part of Nagapattinam district, Southern India: using hydrogeochemistry and GIS interpolation techniques

NASA Astrophysics Data System (ADS)

Gnanachandrasamy, G.; Ramkumar, T.; Venkatramanan, S.; Vasudevan, S.; Chung, S. Y.; Bagyaraj, M.

2015-03-01

The aim of this present study was to evaluate groundwater quality in the lower part of Nagapattinam district, Tamil Nadu, Southern India. A detailed geochemical study of groundwater region is described, and the origin of the chemical composition of groundwater has been qualitatively evaluated, using observations over a period of two seasons premonsoon (June) and monsoon (November) in the year of 2010. To attempt this goal, samples were analysed for various physico-chemical parameters such as temperature, pH, salinity, Na+, Ca2+, K+, Mg2+, Cl-, HCO3 - and SO4 2-. The abundance of major cations concentration in groundwater is as Na > Ca > Mg > K, while that of anions is Cl > SO4 > HCO3. The Piper trilinear diagram indicates Ca-Cl2 facies, and according to USSL diagram, most of the sample exhibits high salinity hazard (C3S1) type in both seasons. It indicates that high salinity (C3) and low sodium (S1) are moderately suitable for irrigation purposes. Gibbs boomerang exhibits most of the samples mainly controlled by evaporation and weathering process sector in both seasons. Irrigation status of the groundwater samples indicates that it was moderately suitable for agricultural purpose. ArcGIS 9.3 software was used for the generation of various thematic maps and the final groundwater quality map. An interpolation technique inverse distance weighting was used to obtain the spatial distribution of groundwater quality parameters. The final map classified the ground quality in the study area. The results of this research show that the development of the management strategies for the aquifer system is vitally necessary.

An empirical study using permutation-based resampling in meta-regression

PubMed Central

2012-01-01

Background In meta-regression, as the number of trials in the analyses decreases, the risk of false positives or false negatives increases. This is partly due to the assumption of normality that may not hold in small samples. Creation of a distribution from the observed trials using permutation methods to calculate P values may allow for less spurious findings. Permutation has not been empirically tested in meta-regression. The objective of this study was to perform an empirical investigation to explore the differences in results for meta-analyses on a small number of trials using standard large sample approaches verses permutation-based methods for meta-regression. Methods We isolated a sample of randomized controlled clinical trials (RCTs) for interventions that have a small number of trials (herbal medicine trials). Trials were then grouped by herbal species and condition and assessed for methodological quality using the Jadad scale, and data were extracted for each outcome. Finally, we performed meta-analyses on the primary outcome of each group of trials and meta-regression for methodological quality subgroups within each meta-analysis. We used large sample methods and permutation methods in our meta-regression modeling. We then compared final models and final P values between methods. Results We collected 110 trials across 5 intervention/outcome pairings and 5 to 10 trials per covariate. When applying large sample methods and permutation-based methods in our backwards stepwise regression the covariates in the final models were identical in all cases. The P values for the covariates in the final model were larger in 78% (7/9) of the cases for permutation and identical for 22% (2/9) of the cases. Conclusions We present empirical evidence that permutation-based resampling may not change final models when using backwards stepwise regression, but may increase P values in meta-regression of multiple covariates for relatively small amount of trials. PMID:22587815

Final Approval of California Air Plan Revision; Antelope Valley Air Quality Management District; VOCs From Motor Vehicle Assembly Coating Operations

EPA Pesticide Factsheets

EPA is taking final action to approve a revision to the Antelope Valley Air Quality Management District (AVAQMD) portion of the California SIP concerning the emissions of volatile organic compounds (VOCs) from motor vehicle assembly coating operations.

77 FR 14473 - Final Guidance on Improving the Process for Preparing Efficient and Timely Environmental Reviews...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-12

... COUNCIL ON ENVIRONMENTAL QUALITY 40 CFR Parts 1500, 1501, 1502, 1503, 1505, 1506, 1507, and 1508 Final Guidance on Improving the Process for Preparing Efficient and Timely Environmental Reviews Under the National Environmental Policy Act AGENCY: Council on Environmental Quality. ACTION: Notice of...

NONDESTRUCTIVE QUALITY CONTROL: SOME SPECIAL METHODS OF IRRADIATION TESTING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van der Klis, T.

1961-06-10

S>Various methods, using open radioactive sources are discussed. In one method, oil is used containing Pd/sup 109/ which is adsorbed by Mg compounds with which the object to be tested is covered after it has been enveloped in a photographic film. Another method consists of coking the material in the radioactive oil and then scanning it with a suitable detector. A third method, applied especially to porous materials, uses pressure to promote the penetration of the radioactive oil into the cracks and fissures. The filtered particle technique is also used for detection of cracks or cavities in porous materials, suchmore » as ceramics, cement, graphite pressed powdered metals, and sintered carbides. In this method, radioactive liquids are used along with fluid fluorescent substances. Finally, a method is mentioned in which radioactive powder is made to adhere to the surface of the investigated objects by means of an electrostatic charge. This method is used for quality control of china, glass, email, and electric insulation material. (OID)« less

The US National Transonic Facility, NTF

NASA Technical Reports Server (NTRS)

Bruce, Walter E., Jr.; Gloss, Blair B.

1989-01-01

The construction of the National Transonic Facility was completed in September 1982 and the start-up and checkout of tunnel systems were performed over the next two years. In August 1984, the Operational Readiness Review (ORR) was conducted and the facility was declared operational for final checkout of cryogenic instrumentation and control systems, and for the aerodynamic calibration and testing to commence. Also, the model access system for the cryogenic mode of operation would be placed into operation along with tunnel testing. Since the ORR, a host of operating problems resulting from the cryogenic environment were identified and solved. These range from making mechanical and electrical systems functional to eliminating temperature induced model vibration to coping with the outgassing of moisture from the thermal insulation. Additionally, a series of aerodynamic tests have demonstrated data quality and provided research data on several configurations. Some of the more significant efforts are reviewed since the ORR and the NTF status concerning hardware, instrumentation and process controls systems, operating constraints imposed by the cryogenic environment, and data quality are summarized.

Gran Telescopio Canarias Commissioning Instrument Optomechanics

NASA Astrophysics Data System (ADS)

Espejo, Carlos; Cuevas, Salvador; Sanchez, Beatriz; Flores, Ruben; Lara, Gerardo; Farah, Alejandro; Godoy, Javier; Bringas, Vicente; Chavoya, Armando; Dorantes, Ariel; Manuel Montoya, Juan; Rangel, Juan Carlos; Devaney, Nicholas; Castro, Javier; Cavaller, Luis

2003-02-01

Under a contract with the GRANTECAN, the Commissioning Instrument is a project developed by a team of Mexican scientists and engineers from the Instrumentation Department of the Astronomy Institute at the UNAM and the CIDESI Engineering Center. This paper will discuss in some detail the final Commissioning Instrument (CI) mechanical design and fabrication. We will also explain the error budget and the barrels design as well as their thermal compensation. The optical design and the control system are discussed in other papers. The CI will just act as a diagnostic tool for image quality verification during the GTC Commissioning Phase. This phase is a quality control process for achieving, verifying, and documenting the performance of each GTC sub-systems. This is a very important step for the telescope life. It will begin on starting day and will last for a year. The CI project started in December 2000. The critical design phase was reviewed in July 2001. The CI manufacturing is currently in progress and most parts are finished. We are now approaching the factory acceptance stage.

Robotic solid phase extraction and high performance liquid chromatographic analysis of ranitidine in serum or plasma.

PubMed

Lloyd, T L; Perschy, T B; Gooding, A E; Tomlinson, J J

1992-01-01

A fully automated assay for the analysis of ranitidine in serum and plasma, with and without an internal standard, was validated. It utilizes robotic solid phase extraction with on-line high performance liquid chromatographic (HPLC) analysis. The ruggedness of the assay was demonstrated over a three-year period. A Zymark Py Technology II robotic system was used for serial processing from initial aspiration of samples from original collection containers, to final direct injection onto the on-line HPLC system. Automated serial processing with on-line analysis provided uniform sample history and increased productivity by freeing the chemist to analyse data and perform other tasks. The solid phase extraction efficiency was 94% throughout the assay range of 10-250 ng/mL. The coefficients of variation for within- and between-day quality control samples ranged from 1 to 6% and 1 to 5%, respectively. Mean accuracy for between-day standards and quality control results ranged from 97 to 102% of the respective theoretical concentrations.

Study of the role of bran water binding and the steric hindrance by bran in straight dough bread making.

PubMed

Hemdane, S; Langenaeken, N A; Jacobs, P J; Verspreet, J; Delcour, J A; Courtin, C M

2018-07-01

This study investigates the effect of the physical presence and water binding of wheat bran during bread making, and the possible mechanisms behind this effect. Regular bran, pericarp-enriched bran and synthetic bran-like particles with different water binding capacities and particle sizes were used. Incorporation of regular and pericarp-enriched bran in dough (15% dm) led to a lower oven rise than the control dough. Bread volumes decreased with 11% and 30%, respectively. Dough with synthetic bran, having a low water binding capacity, displayed a near to normal leavening and oven rise and resulted in a bread volume decrease of only 5% compared to the control. Particle size reduction of regular bran and synthetic bran to an average size of 200 µm did not affect final bread quality. Results indicate that water binding by bran affects bread quality the most, whereas steric hindrance by physical presence of bran particles is less determinative. Copyright © 2018 Elsevier Ltd. All rights reserved.

Image quality evaluation and patient dose assessment of medical fluoroscopic X-ray systems: a national study.

PubMed

Economides, S; Hourdakis, C J; Kalivas, N; Kalathaki, M; Simantirakis, G; Tritakis, P; Manousaridis, G; Vogiatzi, S; Kipouros, P; Boziari, A; Kamenopoulou, V

2008-01-01

This study presents the results from a survey conducted by the Greek Atomic Energy Commission (GAEC), during the period 1998-2003, in 530 public and private owned fluoroscopic X-ray systems in Greece. Certain operational parameters for conventional and remote control systems were assessed, according to a quality control protocol developed by GAEC on the basis of the current literature. Public (91.5%) and private (81.5%) owned fluoroscopic units exhibit high-contrast resolution values over 1 lp mm(-1). Moreover, 88.5 and 87.1% of the fluoroscopic units installed in the public and private sector, respectively, present Maximum Patient Entrance Kerma Rate values lower than 100 mGy min(-1). Additionally, 68.3% of the units assessed were found to perform within the acceptance limits. Finally, the third quartile of the Entrance Surface Dose Rate distribution was estimated according to the Dose Reference Level definition and found equal to 35 mGy min(-1).

Effect of process parameters on formability of laser melting deposited 12CrNi2 alloy steel

NASA Astrophysics Data System (ADS)

Peng, Qian; Dong, Shiyun; Kang, Xueliang; Yan, Shixing; Men, Ping

2018-03-01

As a new rapid prototyping technology, the laser melting deposition technology not only has the advantages of fast forming, high efficiency, but also free control in the design and production chain. Therefore, it has drawn extensive attention from community.With the continuous improvement of steel performance requirements, high performance low-carbon alloy steel is gradually integrated into high-tech fields such as aerospace, high-speed train and armored equipment.However, it is necessary to further explore and optimize the difficult process of laser melting deposited alloy steel parts to achieve the performance and shape control.This article took the orthogonal experiment on alloy steel powder by laser melting deposition ,and revealed the influence rule of the laser power, scanning speed, powder gas flow on the quality of the sample than the dilution rate, surface morphology and microstructure analysis were carried out.Finally, under the optimum technological parameters, the Excellent surface quality of the alloy steel forming part with high density, no pore and cracks was obtained.

Laser Ultrasound Spectroscopy Scanning for 3D Printed Parts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brennan, Guendalyn Kendra

One of the challenges of additive manufacturing is quality control due to the possibility of unseen flaws in the final product. The current methods of inspection are lacking in detail, too slow for practical use, or unable to validate internal structure. This report examines the use of laser ultrasound spectroscopy in layer by layer scans of 3D printed parts as they are created. The result is fast and detailed quality control. An additional advantage of this method is the ability to cancel a print as soon as a defect is detected, therefore saving materials and time. This technique, though simplemore » in concept, has been a challenge to implement. I discuss tweaking the 3D printer configuration, and finding the optimal settings for laser scanning small parts made of ABS plastic, as well as the limits of how small of a detail the laser can detect. These settings include the frequency of the ultrasonic transducer, the speed of the laser, and the distance from the laser to the part.« less

An Adaptive Buddy Check for Observational Quality Control

NASA Technical Reports Server (NTRS)

Dee, Dick P.; Rukhovets, Leonid; Todling, Ricardo; DaSilva, Arlindo M.; Larson, Jay W.; Einaudi, Franco (Technical Monitor)

2000-01-01

An adaptive buddy check algorithm is presented that adjusts tolerances for outlier observations based on the variability of surrounding data. The algorithm derives from a statistical hypothesis test combined with maximum-likelihood covariance estimation. Its stability is shown to depend on the initial identification of outliers by a simple background check. The adaptive feature ensures that the final quality control decisions are not very sensitive to prescribed statistics of first-guess and observation errors, nor on other approximations introduced into the algorithm. The implementation of the algorithm in a global atmospheric data assimilation is described. Its performance is contrasted with that of a non-adaptive buddy check, for the surface analysis of an extreme storm that took place in Europe on 27 December 1999. The adaptive algorithm allowed the inclusion of many important observations that differed greatly from the first guess and that would have been excluded on the basis of prescribed statistics. The analysis of the storm development was much improved as a result of these additional observations.

A New Type of Tea Baking Machine Based on Pro/E Design

NASA Astrophysics Data System (ADS)

Lin, Xin-Ying; Wang, Wei

2017-11-01

In this paper, the production process of wulong tea was discussed, mainly the effect of baking on the quality of tea. The suitable baking temperature of different tea was introduced. Based on Pro/E, a new type of baking machine suitable for wulong tea baking was designed. The working principle, mechanical structure and constant temperature timing intelligent control system of baking machine were expounded. Finally, the characteristics and innovation of new baking machine were discussed.The mechanical structure of this baking machine is more simple and reasonable, and can use the heat of the inlet and outlet, more energy saving and environmental protection. The temperature control part adopts fuzzy PID control, which can improve the accuracy and response speed of temperature control and reduce the dependence of baking operation on skilled experience.

Performance evaluation of power control algorithms in wireless cellular networks

NASA Astrophysics Data System (ADS)

Temaneh-Nyah, C.; Iita, V.

2014-10-01

Power control in a mobile communication network intents to control the transmission power levels in such a way that the required quality of service (QoS) for the users is guaranteed with lowest possible transmission powers. Most of the studies of power control algorithms in the literature are based on some kind of simplified assumptions which leads to compromise in the validity of the results when applied in a real environment. In this paper, a CDMA network was simulated. The real environment was accounted for by defining the analysis area and the network base stations and mobile stations are defined by their geographical coordinates, the mobility of the mobile stations is accounted for. The simulation also allowed for a number of network parameters including the network traffic, and the wireless channel models to be modified. Finally, we present the simulation results of a convergence speed based comparative analysis of three uplink power control algorithms.

Design verification and fabrication of active control systems for the DAST ARW-2 high aspect ratio wing. Part 2: Appendices

NASA Technical Reports Server (NTRS)

Mcgehee, C. R.

1986-01-01

This is Part 2-Appendices of a study conducted under Drones for Aerodynamic and Structural Testing (DAST) Program to accomplish the final design and hardware fabrication for four active control systems compatible with and ready for installation in the NASA Aeroelastic Research Wing No. 2 (ARW-2) and Firebee II drone flight test vehicle. The wing structure was designed so that Active Control Systems (ACS) are required in the normal flight envelope by integrating control system design with aerodynamics and structure technologies. The DAST ARW-2 configuration uses flutter suppression, relaxed static stability, and gust and maneuver load alleviation ACS systems, and an automatic flight control system. Performance goals and criteria were applied to individual systems and the systems collectively to assure that vehicle stability margins, flutter margins, flying qualities, and load reductions were achieved.

Dynamics, stability, and control of maglev systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Y.; Chen, S.S.; Rote, D.M.

1993-06-01

The dynamic response of maglev systems is important in several respects: Safety and ride quality, guideway design, and system costs. The dynamic response of vehicles is the key element in the determination of ride quality, and vehicle stability is one of the important elements relative to safety. To design a proper guideway that provides acceptable ride quality in the stable region, the vehicle dynamics must be understood. The trade-off between guideway smoothness and the levitation and control systems must be considered if maglev systems are to be economically feasible. This paper is a summary of our previous work on dynamics,more » stability and control of maglev systems. First of all, the importance of dynamics of vehicle/guideway of maglev systems is discussed. Emphasis is placed on the modeling vehicle/guideway interactions of maglev systems with a multicar, or multiload vehicle traversing on a single or double-span flexible guideway. Coupled effects of vehicle/guideway interactions in wide range of vehicle speeds with various vehicle and guideway parameters for maglev systems are investigated. Secondly, the alternative control designs of maglev vehicle suspension systems are investigated in this study to achieve safe, stable operation and acceptable ride comfort requires some form of vehicle motion control. Active and semi-active control law designs are introduced into primary and secondary suspensions of maglev vehicles. Finally, this paper discusses the stability of maglev systems based on experimental data, scoping calculations, and simple mathematical models. Divergence and flutter are obtained for coupled vibration of a three-degree-of-freedom maglev vehicle on a guideway consisting of double L-shaped aluminum segments. The theory and analysis developed in this study provides basic stability characteristics and identifies future research needs for maglev systems.« less

Dynamics, stability, and control of maglev systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Y.; Chen, S.S.; Rote, D.M.

1993-01-01

The dynamic response of maglev systems is important in several respects: Safety and ride quality, guideway design, and system costs. The dynamic response of vehicles is the key element in the determination of ride quality, and vehicle stability is one of the important elements relative to safety. To design a proper guideway that provides acceptable ride quality in the stable region, the vehicle dynamics must be understood. The trade-off between guideway smoothness and the levitation and control systems must be considered if maglev systems are to be economically feasible. This paper is a summary of our previous work on dynamics,more » stability and control of maglev systems. First of all, the importance of dynamics of vehicle/guideway of maglev systems is discussed. Emphasis is placed on the modeling vehicle/guideway interactions of maglev systems with a multicar, or multiload vehicle traversing on a single or double-span flexible guideway. Coupled effects of vehicle/guideway interactions in wide range of vehicle speeds with various vehicle and guideway parameters for maglev systems are investigated. Secondly, the alternative control designs of maglev vehicle suspension systems are investigated in this study to achieve safe, stable operation and acceptable ride comfort requires some form of vehicle motion control. Active and semi-active control law designs are introduced into primary and secondary suspensions of maglev vehicles. Finally, this paper discusses the stability of maglev systems based on experimental data, scoping calculations, and simple mathematical models. Divergence and flutter are obtained for coupled vibration of a three-degree-of-freedom maglev vehicle on a guideway consisting of double L-shaped aluminum segments. The theory and analysis developed in this study provides basic stability characteristics and identifies future research needs for maglev systems.« less

Standardization and quality control parameters for Muktā Bhasma (calcined pearl)

PubMed Central

Joshi, Namrata; Sharma, Khemchand; Peter, Hema; Dash, Manoj Kumar

2015-01-01

Background: Muktā Bhasma (MB) is a traditional Ayurvedic preparation for cough, breathlessness, and eye disorders and is a powerful cardiac tonic, mood elevator, and known to promote strength, intellect, and semen production. Objectives: The present research work was conducted to generate fingerprint for raw and processed MB for quality assessment and standardization using classical and other techniques. Setting and Design: Three samples of MB were prepared by purification (śodhana) of Muktā (pearl) followed by repeated calcinations (Māraṇa). Resultant product was subjected to organoleptic tests and Ayurvedic tests for quality control such as rekhāpūrṇatā, vāritaratva, and nirdhūmatva. Materials and Methods: For quality control, physicochemical parameters such as loss on drying, total ash value, acid insoluble ash, specific gravity, pH value, and other tests using techniques such as elemental analysis with energy dispersive X-ray analysis (EDAX), Structural study with powder X-ray diffraction, particle size with scanning electron microscopy (SEM) were carried out on raw Muktā, Śodhita Muktā, and triplicate batches of MB. Results: The study showed that the raw material Muktā was calcium carbonate in aragonite form, which on repeated calcinations was converted into a more stable calcite form. SEM studies revealed that in raw and purified materials the particles were found scattered and unevenly arranged in the range of 718.7–214.7 nm while in final product, uniformly arranged, stable, rod-shaped, and rounded particles with more agglomerates were observed in the range of 279.2–79.93 nm. EDAX analysis revealed calcium as a major ingredient in MB (average 46.32%) which increased gradually in the stages of processing (raw 34.11%, Śodhita 37.5%). Conclusion: Quality control parameters have been quantified for fingerprinting of MB prepared using a particular method. PMID:26600667

Quality and rural-urban comparison of tuberculosis care in Rivers State, Nigeria

PubMed Central

Tobin-West, Charles Ibiene; Isodje, Anastasia

2016-01-01

Introduction Nigeria ranks among countries with the highest burden of tuberculosis. Yet evidence continues to indicate poor treatment outcomes which have been attributed to poor quality of care. This study aims to identify some of the systemic problems in order to inform policy decisions for improved quality of services and treatment outcomes in Nigeria. Methods A comparative assessment of the quality of TB care in rural and urban health facilities was carried out between May and June 2013, employing the Donabedian model of quality assessment. Data was analysed using the SPSS software package version 20.0. The level of significance was set at p < 0.05. Results Health facility infrastructures were more constrained in the urban than rural settings. Both the urban and rural facilities lacked adequate facilities for infection control such as, running water, air filter respirators, hand gloves and extractor fans. Health education and HIV counselling and testing (HCT) were limited in rural facilities compared to urban facilities. Although anti-TB drugs were generally available in both settings, the DOTS strategy in patient care was completely ignored. Finally, laboratory support for diagnosis and patient monitoring was limited in the rural facilities. Conclusion The study highlights suboptimal quality of TB care in Rivers State with limitations in health education and HCT of patients for HIV as well as laboratory support for TB care in rural health facilities. We, therefore, recommend that adequate infection control measures, strict observance of the DOTS strategy and sufficient laboratory support be provided to TB clinics in the State. PMID:27642401

A systematic review of randomized controlled trials for prevention or treatment of atopic dermatitis in dogs: 2008-2011 update.

PubMed

Olivry, Thierry; Bizikova, Petra

2013-02-01

The management of atopic dermatitis (AD) in dogs relies mainly on the use of interventions to reduce pruritus and skin lesions. To provide a critical analysis of recent clinical trials reporting the efficacy and safety of interventions for canine AD. Systematic review of randomized controlled trials (RCTs) published, presented or completed between 2008 and 2011, which enrolled dogs with AD. The search was done using electronic databases, reviewing published meeting abstracts and sending queries to professional email lists. Trials reporting the efficacy of interventions aimed at treating, preventing or reducing glucocorticoid usage in atopic dogs were selected. Twenty-one RCTs were included. We found further moderate-quality evidence of efficacy and safety of oral glucocorticoids and ciclosporin for treatment of canine AD. There was additional moderate-quality evidence of the efficacy of a topical glucocorticoid spray containing hydrocortisone aceponate. Low-quality evidence was found for the efficacy and safety of injectable recombinant interferons, a budesonide leave-on conditioner, a ciclosporin topical nano-emulsion and oral fexofenadine. There is low-quality evidence of efficacy of oral masitinib, with a need for monitoring for protein-losing nephropathy. Finally, we uncovered low-quality evidence of efficacy of a commercial diet as a glucocorticoid-sparing intervention and of a glucocorticoid spray as a flare-delaying measure. Very low-quality evidence was found for the efficacy of other interventions. Topical or oral glucocorticoids and oral ciclosporin remain the interventions with highest evidence for efficacy and relative safety for treatment of canine AD. © 2013 The Authors. Veterinary Dermatology © 2013 ESVD and ACVD.

Sensory modulation and sleep quality among adults with learning disabilities: a quasi-experimental case-control design study.

PubMed

Sharfi, Kineret; Rosenblum, Sara

2015-01-01

Following the International Classification of Functioning, Disability and Health (ICF) concepts, this study examines body functions such as sensory modulation and sleep quality among adults with learning disabilities (LD). One hundred and ten participants, 55 adults with LD and 55 matched controls (mean age 30 years) filled in a socio-demographic questionnaire, the Adults/Adolescents Sensory Profile (AASP), and the Mini Sleep Questionnaire (MSQ). Chi-tests, Mann-Whitney tests, and Kolmogorov-Smirnov tests were conducted to examine group differences related to socio-demographic characteristics and body functions. Correlation and regression analyses were conducted to examine relationships between body functions. Significant differences were found between the groups in: (a) unique socio-demographic variables: high-schools attended, family status and number of children; (b) body functions: low registration and sensory sensitivity (p < .001), sensory avoiding (p = .002), sensory seeking (p = .021) and sleep quality (p < .001). Significant correlations were found between AASP subscale scores and the MSQ final score in each group. Regression analysis revealed that for the entire sample (N = 108), low registration accounted for 10.2% of the variance of sleep quality above group membership (p < .001), while in a separate examination of adults with LD (n = 53), low registration accounted for 19.9% of the variance of sleep quality (p < .001). Adults with LD need to be studied through a health-related perspective such as the ICF model to gain further understanding of their unique characteristics and daily needs. Sensory and sleep functions of adults with LD should be further studied in the context of health related quality of life.

Responses of Rapid Viscoanalyzer Profile and Other Rice Grain Qualities to Exogenously Applied Plant Growth Regulators under High Day and High Night Temperatures

PubMed Central

Fahad, Shah; Hussain, Saddam; Saud, Shah; Hassan, Shah; Chauhan, Bhagirath Singh; Khan, Fahad; Ihsan, Muhammad Zahid; Ullah, Abid; Wu, Chao; Bajwa, Ali Ahsan; Alharby, Hesham; Amanullah; Nasim, Wajid; Shahzad, Babar; Tanveer, Mohsin; Huang, Jianliang

2016-01-01

High-temperature stress degrades the grain quality of rice; nevertheless, the exogenous application of plant growth regulators (PGRs) might alleviate the negative effects of high temperatures. In the present study, we investigated the responses of rice grain quality to exogenously applied PGRs under high day temperatures (HDT) and high night temperatures (HNT) under controlled conditions. Four different combinations of ascorbic acid (Vc), alpha-tocopherol (Ve), brassinosteroids (Br), methyl jasmonates (MeJA) and triazoles (Tr) were exogenously applied to two rice cultivars (IR-64 and Huanghuazhan) prior to the high-temperature treatment. A Nothing applied Control (NAC) was included for comparison. The results demonstrated that high-temperature stress was detrimental for grain appearance and milling qualities and that both HDT and HNT reduced the grain length, grain width, grain area, head rice percentage and milled rice percentage but increased the chalkiness percentage and percent area of endosperm chalkiness in both cultivars compared with ambient temperature (AT). Significantly higher grain breakdown, set back, consistence viscosity and gelatinization temperature, and significantly lower peak, trough and final viscosities were observed under high-temperature stress compared with AT. Thus, HNT was more devastating for grain quality than HDT. The exogenous application of PGRs ameliorated the adverse effects of high temperature in both rice cultivars, and Vc+Ve+MejA+Br was the best combination for both cultivars under high temperature stress. PMID:27472200

Evaluation of control over the microbiological contamination of carcasses in a lamb carcass dressing process operated with or without pasteurizing treatment.

PubMed

Milios, K; Mataragas, M; Pantouvakis, A; Drosinos, E H; Zoiopoulos, P E

2011-03-30

The aim of this study was to quantify the hygienic status of a lamb slaughterhouse by means of multivariate statistical analysis, to demonstrate how the microbiological data could be exploited to improve the lamb slaughter process by constructing control charts and to evaluate the potential effect of an intervention step such as steam application on the microbiological quality of lamb carcasses. Results showed that pelt removal and evisceration were hygienically uncontrolled. TVC and Enterobacteriaceae progressively increased from the stage 'after pelt removal of hind and forelegs/before final pulling' to the stage 'after evisceration/before pluck removal' thus indicating possible deposition of microorganisms during these operations. It seems that the processing stages of freshly produced carcasses were better distinguished by Enterobacteriaceae, with evisceration contributing mostly to the final Enterobacteriaceae counts. Application of steam during the lamb slaughter process reduced microbial counts without adverse effects on the organoleptic characteristics of the carcasses. Moreover, the construction of control charts showed that decontamination with steam contributed to the maintenance of an in control process compared to that before the application of steam, suggesting the potential use of steam as an intervention step during the lamb slaughter process. Copyright © 2011 Elsevier B.V. All rights reserved.

Effect of Silicon in U-10Mo Alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kautz, Elizabeth J.; Devaraj, Arun; Kovarik, Libor

2017-08-31

This document details a method for evaluating the effect of silicon impurity content on U-10Mo alloys. Silicon concentration in U-10Mo alloys has been shown to impact the following: volume fraction of precipitate phases, effective density of the final alloy, and 235-U enrichment in the gamma-UMo matrix. This report presents a model for calculating these quantities as a function of Silicon concentration, which along with fuel foil characterization data, will serve as a reference for quality control of the U-10Mo final alloy Si content. Additionally, detailed characterization using scanning electron microscope imaging, transmission electron microscope diffraction, and atom probe tomography showedmore » that Silicon impurities present in U-10Mo alloys form a Si-rich precipitate phase.« less

Quality-by-Design approach to monitor the operation of a batch bioreactor in an industrial avian vaccine manufacturing process.

PubMed

Largoni, Martina; Facco, Pierantonio; Bernini, Donatella; Bezzo, Fabrizio; Barolo, Massimiliano

2015-10-10

Monitoring batch bioreactors is a complex task, due to the fact that several sources of variability can affect a running batch and impact on the final product quality. Additionally, the product quality itself may not be measurable on line, but requires sampling and lab analysis taking several days to be completed. In this study we show that, by using appropriate process analytical technology tools, the operation of an industrial batch bioreactor used in avian vaccine manufacturing can be effectively monitored as the batch progresses. Multivariate statistical models are built from historical databases of batches already completed, and they are used to enable the real time identification of the variability sources, to reliably predict the final product quality, and to improve process understanding, paving the way to a reduction of final product rejections, as well as to a reduction of the product cycle time. It is also shown that the product quality "builds up" mainly during the first half of a batch, suggesting on the one side that reducing the variability during this period is crucial, and on the other side that the batch length can possibly be shortened. Overall, the study demonstrates that, by using a Quality-by-Design approach centered on the appropriate use of mathematical modeling, quality can indeed be built "by design" into the final product, whereas the role of end-point product testing can progressively reduce its importance in product manufacturing. Copyright © 2015 Elsevier B.V. All rights reserved.

Review of bilayer tablet technology.

PubMed

Abebe, Admassu; Akseli, Ilgaz; Sprockel, Omar; Kottala, Niranjan; Cuitiño, Alberto M

2014-01-30

Therapeutic strategies based on oral delivery of bilayer (and multilayer) tablets are gaining more acceptance among brand and generic products due to a confluence of factors including advanced delivery strategies, patient compliance and combination therapy. Successful manufacturing of these ever more complex systems needs to overcome a series of challenges from formulation design to tablet press monitoring and control. This article provides an overview of the state-of-the-art of bilayer tablet technology, highlighting the main benefits of this type of oral dosage forms while providing a description of current challenges and advances toward improving manufacturing practices and product quality. Several aspects relevant to bilayer tablet manufacturing are addressed including material properties, lubrication, layer ordering, layer thickness, layer weight control, as well as first and final compression forces. A section is also devoted to bilayer tablet characterization that present additional complexities associated with interfaces between layers. The available features of the manufacturing equipment for bilayer tablet production are also described indicating the different strategies for sensing and controls offered by bilayer tablet press manufacturers. Finally, a roadmap for bilayer tablet manufacturing is advanced as a guideline to formulation design and selection of process parameters and equipment. Copyright © 2013 Elsevier B.V. All rights reserved.

Medicare program; hospital outpatient prospective payment system and CY 2007 payment rates; CY 2007 update to the ambulatory surgical center covered procedures list; Medicare administrative contractors; and reporting hospital quality data for FY 2008 inpatient prospective payment system annual payment update program--HCAHPS survey, SCIP, and mortality. Final rule with comment period and final rule.

PubMed

2006-11-24

This final rule with comment period revises the Medicare hospital outpatient prospective payment system to implement applicable statutory requirements and changes arising from our continuing experience with this system, and to implement certain related provisions of the Medicare Prescription Drug, Improvement, and Modernization Act (MMA) of 2003 and the Deficit Reduction Act (DRA) of 2005. In this final rule with comment period, we describe changes to the amounts and factors used to determine the payment rates for Medicare hospital outpatient services paid under the prospective payment system. These changes are applicable to services furnished on or after January 1, 2007. In addition, this final rule with comment period implements future CY 2009 required reporting on quality measures for hospital outpatient services paid under the prospective payment system. This final rule with comment period revises the current list of procedures that are covered when furnished in a Medicare-approved ambulatory surgical center (ASC), which are applicable to services furnished on or after January 1, 2007. This final rule with comment period revises the emergency medical screening requirements for critical access hospitals (CAHs). This final rule with comment period supports implementation of a restructuring of the contracting entities responsibilities and functions that support the adjudication of Medicare fee-for-service (FFS) claims. This restructuring is directed by section 1874A of the Act, as added by section 911 of the MMA. The prior separate Medicare intermediary and Medicare carrier contracting authorities under Title XVIII of the Act have been replaced with the Medicare Administrative Contractor (MAC) authority. This final rule continues to implement the requirements of the DRA that require that we expand the "starter set" of 10 quality measures that we used in FY 2005 and FY 2006 for the hospital inpatient prospective payment system (IPPS) Reporting Hospital Quality Data for the Annual Payment Update (RHQDAPU) program. We began to adopt expanded measures effective for payments beginning in FY 2007. In this rule, we are finalizing additional quality measures for the expanded set of measures for FY 2008 payment purposes. These measures include the HCAHPS survey, as well as Surgical Care Improvement Project (SCIP, formerly Surgical Infection Prevention (SIP)), and Mortality quality measures.

Red beet and betaine as ingredients in diets of rainbow trout (Oncorhynchus mykiss): effects on growth performance, nutrient retention and flesh quality.

PubMed

Pinedo-Gil, Julia; Tomás-Vidal, Ana; Jover-Cerdá, Miguel; Tomás-Almenar, Cristina; Sanz-Calvo, Miguel Ángel; Martín-Diana, Ana Belén

2017-12-01

The objective of the study was to evaluate the impact of different concentrations of dietary red beet and betaine on the growth performance and fish flesh quality of rainbow trout. Therefore, a control diet was compared with four diets in which two levels of red beet (14% and 28%) and betaine (0.9% and 1.63%) were incorporated in combination. The study was set up with an average body weight of 69 ± 2.2 g and finished when fish reached commercial weight (175-250 g) after 105 d. The impact of the diets was studied based on the growth performance, biometric indexes, proximal composition, protein and fat retention efficiencies and apparent nutrient digestibility by fish reared on a recirculation system. Further estimates were the effect of red beet and betaine on the flesh proximate composition and quality of the final product (water activity, colour, texture, thiobarbituric acid reactive substances and sensory characteristics). Results showed that inclusion of 14% red beet and 0.9% betaine did not affect growth, nutritive or biometric parameters and nutrient retention when compared with the control diet. However, higher levels of red beet and betaine had negative effects on growth and nutritive parameters. The tested ingredients enhanced quality parameters regardless of the concentration used. After feeding the red beet and betaine, fish flesh showed lower water activity and better textural and colour properties than the control and also a dose-dependent effect on lipid oxidation was observed.

SNPflow: A Lightweight Application for the Processing, Storing and Automatic Quality Checking of Genotyping Assays

PubMed Central

Schönherr, Sebastian; Neuner, Mathias; Forer, Lukas; Specht, Günther; Kloss-Brandstätter, Anita; Kronenberg, Florian; Coassin, Stefan

2013-01-01

Single nucleotide polymorphisms (SNPs) play a prominent role in modern genetics. Current genotyping technologies such as Sequenom iPLEX, ABI TaqMan and KBioscience KASPar made the genotyping of huge SNP sets in large populations straightforward and allow the generation of hundreds of thousands of genotypes even in medium sized labs. While data generation is straightforward, the subsequent data conversion, storage and quality control steps are time-consuming, error-prone and require extensive bioinformatic support. In order to ease this tedious process, we developed SNPflow. SNPflow is a lightweight, intuitive and easily deployable application, which processes genotype data from Sequenom MassARRAY (iPLEX) and ABI 7900HT (TaqMan, KASPar) systems and is extendible to other genotyping methods as well. SNPflow automatically converts the raw output files to ready-to-use genotype lists, calculates all standard quality control values such as call rate, expected and real amount of replicates, minor allele frequency, absolute number of discordant replicates, discordance rate and the p-value of the HWE test, checks the plausibility of the observed genotype frequencies by comparing them to HapMap/1000-Genomes, provides a module for the processing of SNPs, which allow sex determination for DNA quality control purposes and, finally, stores all data in a relational database. SNPflow runs on all common operating systems and comes as both stand-alone version and multi-user version for laboratory-wide use. The software, a user manual, screenshots and a screencast illustrating the main features are available at http://genepi-snpflow.i-med.ac.at. PMID:23527209

Improved Lunar Lander Handling Qualities Through Control Response Type and Display Enhancements

NASA Technical Reports Server (NTRS)

Mueller, Eric Richard; Bilimoria, Karl D.; Frost, Chad Ritchie

2010-01-01

A piloted simulation that studied the handling qualities for a precision lunar landing task from final approach to touchdown is presented. A vehicle model based on NASA's Altair Lunar Lander was used to explore the design space around the nominal vehicle configuration to determine which combination of factors provides satisfactory pilot-vehicle performance and workload; details of the control and propulsion systems not available for that vehicle were derived from Apollo Lunar Module data. The experiment was conducted on a large motion base simulator. Eight Space Shuttle and Apollo pilot astronauts and three NASA test pilots served as evaluation pilots, providing Cooper-Harper ratings, Task Load Index ratings and qualitative comments. Each pilot flew seven combinations of control response types and three sets of displays, including two varieties of guidance and a nonguided approach. The response types included Rate Command with Attitude Hold, which was used in the original Apollo Moon landings, a Velocity Increment Command response type designed for up-and-away flight, three response types designed specifically for the vertical descent portion of the trajectory, and combinations of these. It was found that Velocity Increment Command significantly improved handling qualities when compared with the baseline Apollo design, receiving predominantly Level 1 ratings. This response type could be flown with or without explicit guidance cues, something that was very difficult with the baseline design, and resulted in approximately equivalent touchdown accuracies and propellant burn as the baseline response type. The response types designed to be used exclusively in the vertical descent portion of the trajectory did not improve handling qualities.

Fitting relationship between the beam quality β factor of high-energy laser and the wavefront aberration of laser beam

NASA Astrophysics Data System (ADS)

Ji, Zhong-Ye; Zhang, Xiao-Fang

2018-01-01

The mathematical relation between the beam quality β factor of high-energy laser and the wavefront aberration of laser beam is important in beam quality control theory of the high-energy laser weapon system. In order to obtain this mathematical relation, numerical simulation is used in the research. Firstly, the Zernike representations of typically distorted atmospheric wavefront aberrations caused by the Kolmogoroff turbulence are generated. And then, the corresponding beam quality β factors of the different distorted wavefronts are calculated numerically through fast Fourier transform. Thus, the statistical distribution rule between the beam quality β factors of high-energy laser and the wavefront aberrations of the beam can be established by the calculated results. Finally, curve fitting method is chosen to establish the mathematical fitting relationship of these two parameters. And the result of the curve fitting shows that there is a quadratic curve relation between the beam quality β factor of high-energy laser and the wavefront aberration of laser beam. And in this paper, 3 fitting curves, in which the wavefront aberrations are consisted of Zernike Polynomials of 20, 36, 60 orders individually, are established to express the relationship between the beam quality β factor and atmospheric wavefront aberrations with different spatial frequency.

Assessment of Learning Gains Associated with Independent Exam Analysis in Introductory Biology

PubMed Central

William, Adrienne E.; Aguilar-Roca, Nancy M.; Tsai, Michelle; Wong, Matthew; Beaupré, Marin Moravec; O’Dowd, Diane K.

2011-01-01

This study evaluates the impact of an independent postmidterm question analysis exercise on the ability of students to answer subsequent exam questions on the same topics. It was conducted in three sections (∼400 students/section) of introductory biology. Graded midterms were returned electronically, and each student was assigned a subset of questions answered incorrectly by more than 40% of the class to analyze as homework. The majority of questions were at Bloom's application/analysis level; this exercise therefore emphasized learning at these higher levels of cognition. Students in each section answered final exam questions matched by topic to all homework questions, providing a within-class control group for each question. The percentage of students who correctly answered the matched final exam question was significantly higher (p < 0.05) in the Topic Analysis versus Control Analysis group for seven of 19 questions. We identified two factors that influenced activity effectiveness: 1) similarity in topic emphasis of the midterm–final exam question pair and 2) quality of the completed analysis homework. Our data suggest that this easy-to-implement exercise will be useful in large-enrollment classes to help students develop self-regulated learning skills. Additional strategies to help introductory students gain a broader understanding of topic areas are discussed. PMID:22135369

Assessment of learning gains associated with independent exam analysis in introductory biology.

PubMed

Williams, Adrienne E; William, Adrienne E; Aguilar-Roca, Nancy M; Tsai, Michelle; Wong, Matthew; Beaupré, Marin Moravec; O'Dowd, Diane K

2011-01-01

This study evaluates the impact of an independent postmidterm question analysis exercise on the ability of students to answer subsequent exam questions on the same topics. It was conducted in three sections (∼400 students/section) of introductory biology. Graded midterms were returned electronically, and each student was assigned a subset of questions answered incorrectly by more than 40% of the class to analyze as homework. The majority of questions were at Bloom's application/analysis level; this exercise therefore emphasized learning at these higher levels of cognition. Students in each section answered final exam questions matched by topic to all homework questions, providing a within-class control group for each question. The percentage of students who correctly answered the matched final exam question was significantly higher (p < 0.05) in the Topic Analysis versus Control Analysis group for seven of 19 questions. We identified two factors that influenced activity effectiveness: 1) similarity in topic emphasis of the midterm-final exam question pair and 2) quality of the completed analysis homework. Our data suggest that this easy-to-implement exercise will be useful in large-enrollment classes to help students develop self-regulated learning skills. Additional strategies to help introductory students gain a broader understanding of topic areas are discussed.

Target for improvement: a cluster randomised trial of public involvement in quality-indicator prioritisation (intervention development and study protocol)

PubMed Central

2011-01-01

Background Public priorities for improvement often differ from those of clinicians and managers. Public involvement has been proposed as a way to bridge the gap between professional and public clinical care priorities but has not been studied in the context of quality-indicator choice. Our objective is to assess the feasibility and impact of public involvement on quality-indicator choice and agreement with public priorities. Methods We will conduct a cluster randomised controlled trial comparing quality-indicator prioritisation with and without public involvement. In preparation for the trial, we developed a 'menu' of quality indicators, based on a systematic review of existing validated indicator sets. Participants (public representatives, clinicians, and managers) will be recruited from six participating sites. In intervention sites, public representatives will be involved through direct participation (public representatives, clinicians, and managers will deliberate together to agree on quality-indicator choice and use) and consultation (individual public recommendations for improvement will be collected and presented to decision makers). In control sites, only clinicians and managers will take part in the prioritisation process. Data on quality-indicator choice and intended use will be collected. Our primary outcome will compare quality-indicator choice and agreement with public priorities between intervention and control groups. A process evaluation based on direct observation, videorecording, and participants' assessment will be conducted to help explain the study's results. The marginal cost of public involvement will also be assessed. Discussion We identified 801 quality indicators that met our inclusion criteria. An expert panel agreed on a final set of 37 items containing validated quality indicators relevant for chronic disease prevention and management in primary care. We pilot tested our public-involvement intervention with 27 participants (11 public representatives and 16 clinicians and managers) and our study instruments with an additional 21 participants, which demonstrated the feasibility of the intervention and generated important insights and adaptations to engage public representatives more effectively. To our knowledge, this study is the first trial of public involvement in quality-indicator prioritisation, and its results could foster more effective upstream engagement of patients and the public in clinical practice improvement. Trial registration NTR2496 (Netherlands National Trial Register, http://www.trialregister.nl). PMID:21554691