46 CFR 160.156-15 - Production inspections, tests, quality control, and conformance of rescue boats and fast rescue...

Code of Federal Regulations, 2013 CFR

2013-10-01

... materials are as per the plans approved under § 160.156-13(h) of this subpart. (2) Post assembly tests and... 46 Shipping 6 2013-10-01 2013-10-01 false Production inspections, tests, quality control, and... inspections, tests, quality control, and conformance of rescue boats and fast rescue boats. (a) Unless the...

7 CFR 1728.202 - RUS Bulletin 1728H-702, RUS Specification for Quality Control and Inspection of Timber Products.

Code of Federal Regulations, 2010 CFR

2010-01-01

... calendar year. (2) Ultimate quality control is the responsibility of the producer's management; however, a... 7 Agriculture 11 2010-01-01 2010-01-01 false RUS Bulletin 1728H-702, RUS Specification for Quality... for Quality Control and Inspection of Timber Products. (a) Scope. This specification describes in more...

46 CFR 160.135-15 - Production inspections, tests, quality control, and conformance of lifeboats.

Code of Federal Regulations, 2014 CFR

2014-10-01

... materials are as per the plans approved under § 160.135-13(h) of this subpart. (2) Post assembly tests and... each design must pass each of the tests described in the IMO Revised recommendation on testing, part 2... 46 Shipping 6 2014-10-01 2014-10-01 false Production inspections, tests, quality control, and...

A whole process quality control system for energy measuring instruments inspection based on IOT technology

NASA Astrophysics Data System (ADS)

Yin, Bo; Liu, Li; Wang, Jiahan; Li, Xiran; Liu, Zhenbo; Li, Dewei; Wang, Jun; Liu, Lu; Wu, Jun; Xu, Tingting; Cui, He

2017-10-01

Electric energy measurement as a basic work, an accurate measurements play a vital role for the economic interests of both parties of power supply, the standardized management of the measurement laboratory at all levels is a direct factor that directly affects the fairness of measurement. Currently, the management of metering laboratories generally uses one-dimensional bar code as the recognition object, advances the testing process by manual management, most of the test data requires human input to generate reports. There are many problems and potential risks in this process: Data cannot be saved completely, cannot trace the status of inspection, the inspection process isn't completely controllable and so on. For the provincial metrology center's actual requirements of the whole process management for the performance test of the power measuring appliances, using of large-capacity RF tags as a process management information media, we developed a set of general measurement experiment management system, formulated a standardized full performance test process, improved the raw data recording mode of experimental process, developed a storehouse automatic inventory device, established a strict test sample transfer and storage system, ensured that all the raw data of the inspection can be traced back, achieved full life-cycle control of the sample, significantly improved the quality control level and the effectiveness of inspection work.

Automated surface quality inspection with ARGOS: a case study

NASA Astrophysics Data System (ADS)

Kiefhaber, Daniel; Etzold, Fabian; Warken, Arno F.; Asfour, Jean-Michel

2017-06-01

The commercial availability of automated inspection systems for optical surfaces specified according to ISO 10110-7 promises unsupervised and automated quality control with reproducible results. In this study, the classification results of the ARGOS inspection system are compared to the decisions by well-trained inspectors based on manual-visual inspection. Both are found to agree in 93.6% of the studied cases. Exemplary cases with differing results are studied, and shown to be partly caused by shortcomings of the ISO 10110-7 standard, which was written for the industry standard manual-visual inspection. Applying it to high resolution images of the whole surface of objective machine vision systems brings with it a few challenges which are discussed.

[Pharmaceutical product quality control and good manufacturing practices].

PubMed

Hiyama, Yukio

2010-01-01

This report describes the roles of Good Manufacturing Practices (GMP) in pharmaceutical product quality control. There are three keys to pharmaceutical product quality control. They are specifications, thorough product characterization during development, and adherence to GMP as the ICH Q6A guideline on specifications provides the most important principles in its background section. Impacts of the revised Pharmaceutical Affairs Law (rPAL) which became effective in 2005 on product quality control are discussed. Progress of ICH discussion for Pharmaceutical Development (Q8), Quality Risk Management (Q9) and Pharmaceutical Quality System (Q10) are reviewed. In order to reconstruct GMP guidelines and GMP inspection system in the regulatory agencies under the new paradigm by rPAL and the ICH, a series of Health Science studies were conducted. For GMP guidelines, product GMP guideline, technology transfer guideline, laboratory control guideline and change control system guideline were written. For the GMP inspection system, inspection check list, inspection memo and inspection scenario were proposed also by the Health Science study groups. Because pharmaceutical products and their raw materials are manufactured and distributed internationally, collaborations with other national authorities are highly desired. In order to enhance the international collaborations, consistent establishment of GMP inspection quality system throughout Japan will be essential.

Inspection criteria ensure quality control of parallel gap soldering

NASA Technical Reports Server (NTRS)

Burka, J. A.

1968-01-01

Investigation of parallel gap soldering of electrical leads resulted in recommendation on material preparation, equipment, process control, and visual inspection criteria to ensure reliable solder joints. The recommendations will minimize problems in heat-dwell time, amount of solder, bridging conductors, and damage of circuitry.

Collection, storage, inspection and quality control of platelet concentrates obtained by apheresis: The situation in Spain.

PubMed

Castrillo, Azucena; Jimenez-Marco, Teresa; Arroyo, José L; Jurado, María L; Larrea, Luis; Maymo, Rosa M; Monge, Jorge; Muñoz, Carmen; Pajares, Ángel; Yáñez, Marta

2017-06-01

Diverse variables are involved in apheresis platelet collection, processing and storage. This survey shows how these are realized in Spain. An analysis of collected data was performed in a questionnaire completed by ten Transfusion Centers (TC) which perform between 50 and 520 apheresis procedures per month. This information comprises the procedures used to collect, inspect and store apheresis platelet concentrates (PC), and quality control data. Macroscopic inspection of PC is performed in all TC, especially during the first few hours post-collection and before distribution. The type of processor, duration of post-collection resting periods and temperature from the time of collection until distribution are similar in all TC. In 80% of TC, PC with small and scarce aggregates are distributed to transfusion services. The presence of clumps is influenced by type of processor, female donor, cold ambient temperature and collection of hyperconcentrated platelets, and is often recurrent in the same donor, although some TC have not found any influential variables. Overall, no objective inspection methods are followed, although there are exceptions. The degree of compliance with quality control parameters, such as the number of units studied, mean platelet yield, residual leukocyte counts and pH at expiry date, is acceptable in all TC. Compliance in terms of number of microbiological culture samples is variable. The usual practice in Spanish TC with respect to the collection, post-collection handling and storage of apheresis PC can be considered uniform, although some specific aspects of analyses should follow more objective methods. Copyright © 2017 Elsevier Ltd. All rights reserved.

23 CFR 650.313 - Inspection procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Quality control and quality assurance. Assure systematic quality control (QC) and quality assurance (QA... periodic field review of inspection teams, periodic bridge inspection refresher training for program managers and team leaders, and independent review of inspection reports and computations. (h) Follow-up on...

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 2 2013-07-01 2013-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 2 2010-07-01 2010-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 2 2011-07-01 2011-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 2 2012-07-01 2012-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

46 CFR 160.156-15 - Production inspections, tests, quality control, and conformance of rescue boats and fast rescue...

Code of Federal Regulations, 2014 CFR

2014-10-01

... materials are as per the plans approved under § 160.156-13(h) of this subpart. (2) Post assembly tests and... of each design must pass each of the tests described in the IMO Revised recommendation on testing... 46 Shipping 6 2014-10-01 2014-10-01 false Production inspections, tests, quality control, and...

On-line welding quality inspection system for steel pipe based on machine vision

NASA Astrophysics Data System (ADS)

Yang, Yang

2017-05-01

In recent years, high frequency welding has been widely used in production because of its advantages of simplicity, reliability and high quality. In the production process, how to effectively control the weld penetration welding, ensure full penetration, weld uniform, so as to ensure the welding quality is to solve the problem of the present stage, it is an important research field in the field of welding technology. In this paper, based on the study of some methods of welding inspection, a set of on-line welding quality inspection system based on machine vision is designed.

7 CFR 58.928 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be...

Network-based production quality control

NASA Astrophysics Data System (ADS)

Kwon, Yongjin; Tseng, Bill; Chiou, Richard

2007-09-01

This study investigates the feasibility of remote quality control using a host of advanced automation equipment with Internet accessibility. Recent emphasis on product quality and reduction of waste stems from the dynamic, globalized and customer-driven market, which brings opportunities and threats to companies, depending on the response speed and production strategies. The current trends in industry also include a wide spread of distributed manufacturing systems, where design, production, and management facilities are geographically dispersed. This situation mandates not only the accessibility to remotely located production equipment for monitoring and control, but efficient means of responding to changing environment to counter process variations and diverse customer demands. To compete under such an environment, companies are striving to achieve 100%, sensor-based, automated inspection for zero-defect manufacturing. In this study, the Internet-based quality control scheme is referred to as "E-Quality for Manufacturing" or "EQM" for short. By its definition, EQM refers to a holistic approach to design and to embed efficient quality control functions in the context of network integrated manufacturing systems. Such system let designers located far away from the production facility to monitor, control and adjust the quality inspection processes as production design evolves.

7 CFR 58.335 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.335 Section 58.335... Procedures § 58.335 Quality control tests. All milk, cream and related products are subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow...

WELDSMART: A vision-based expert system for quality control

NASA Technical Reports Server (NTRS)

Andersen, Kristinn; Barnett, Robert Joel; Springfield, James F.; Cook, George E.

1992-01-01

This work was aimed at exploring means for utilizing computer technology in quality inspection and evaluation. Inspection of metallic welds was selected as the main application for this development and primary emphasis was placed on visual inspection, as opposed to other inspection methods, such as radiographic techniques. Emphasis was placed on methodologies with the potential for use in real-time quality control systems. Because quality evaluation is somewhat subjective, despite various efforts to classify discontinuities and standardize inspection methods, the task of using a computer for both inspection and evaluation was not trivial. The work started out with a review of the various inspection techniques that are used for quality control in welding. Among other observations from this review was the finding that most weld defects result in abnormalities that may be seen by visual inspection. This supports the approach of emphasizing visual inspection for this work. Quality control consists of two phases: (1) identification of weld discontinuities (some of which may be severe enough to be classified as defects), and (2) assessment or evaluation of the weld based on the observed discontinuities. Usually the latter phase results in a pass/fail judgement for the inspected piece. It is the conclusion of this work that the first of the above tasks, identification of discontinuities, is the most challenging one. It calls for sophisticated image processing and image analysis techniques, and frequently ad hoc methods have to be developed to identify specific features in the weld image. The difficulty of this task is generally not due to limited computing power. In most cases it was found that a modest personal computer or workstation could carry out most computations in a reasonably short time period. Rather, the algorithms and methods necessary for identifying weld discontinuities were in some cases limited. The fact that specific techniques were finally developed and

A laser-based vision system for weld quality inspection.

PubMed

Huang, Wei; Kovacevic, Radovan

2011-01-01

Welding is a very complex process in which the final weld quality can be affected by many process parameters. In order to inspect the weld quality and detect the presence of various weld defects, different methods and systems are studied and developed. In this paper, a laser-based vision system is developed for non-destructive weld quality inspection. The vision sensor is designed based on the principle of laser triangulation. By processing the images acquired from the vision sensor, the geometrical features of the weld can be obtained. Through the visual analysis of the acquired 3D profiles of the weld, the presences as well as the positions and sizes of the weld defects can be accurately identified and therefore, the non-destructive weld quality inspection can be achieved.

A Laser-Based Vision System for Weld Quality Inspection

PubMed Central

Huang, Wei; Kovacevic, Radovan

2011-01-01

Welding is a very complex process in which the final weld quality can be affected by many process parameters. In order to inspect the weld quality and detect the presence of various weld defects, different methods and systems are studied and developed. In this paper, a laser-based vision system is developed for non-destructive weld quality inspection. The vision sensor is designed based on the principle of laser triangulation. By processing the images acquired from the vision sensor, the geometrical features of the weld can be obtained. Through the visual analysis of the acquired 3D profiles of the weld, the presences as well as the positions and sizes of the weld defects can be accurately identified and therefore, the non-destructive weld quality inspection can be achieved. PMID:22344308

Quality Inspection and Analysis of Three-Dimensional Geographic Information Model Based on Oblique Photogrammetry

NASA Astrophysics Data System (ADS)

Dong, S.; Yan, Q.; Xu, Y.; Bai, J.

2018-04-01

In order to promote the construction of digital geo-spatial framework in China and accelerate the construction of informatization mapping system, three-dimensional geographic information model emerged. The three-dimensional geographic information model based on oblique photogrammetry technology has higher accuracy, shorter period and lower cost than traditional methods, and can more directly reflect the elevation, position and appearance of the features. At this stage, the technology of producing three-dimensional geographic information models based on oblique photogrammetry technology is rapidly developing. The market demand and model results have been emerged in a large amount, and the related quality inspection needs are also getting larger and larger. Through the study of relevant literature, it is found that there are a lot of researches on the basic principles and technical characteristics of this technology, and relatively few studies on quality inspection and analysis. On the basis of summarizing the basic principle and technical characteristics of oblique photogrammetry technology, this paper introduces the inspection contents and inspection methods of three-dimensional geographic information model based on oblique photogrammetry technology. Combined with the actual inspection work, this paper summarizes the quality problems of three-dimensional geographic information model based on oblique photogrammetry technology, analyzes the causes of the problems and puts forward the quality control measures. It provides technical guidance for the quality inspection of three-dimensional geographic information model data products based on oblique photogrammetry technology in China and provides technical support for the vigorous development of three-dimensional geographic information model based on oblique photogrammetry technology.

48 CFR 552.246-70 - Source Inspection by Quality Approved Manufacturer.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Quality Approved Manufacturer. 552.246-70 Section 552.246-70 Federal Acquisition Regulations System... Provisions and Clauses 552.246-70 Source Inspection by Quality Approved Manufacturer. As prescribed in 546.302-70, insert the following clause: Source Inspection by Quality Approved Manufacturer (JUL 09) (a...

48 CFR 552.246-70 - Source Inspection by Quality Approved Manufacturer.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Quality Approved Manufacturer. 552.246-70 Section 552.246-70 Federal Acquisition Regulations System... Provisions and Clauses 552.246-70 Source Inspection by Quality Approved Manufacturer. As prescribed in 546.302-70, insert the following clause: Source Inspection by Quality Approved Manufacturer (JUL 09) (a...

Digital Camera Control for Faster Inspection

NASA Technical Reports Server (NTRS)

Brown, Katharine; Siekierski, James D.; Mangieri, Mark L.; Dekome, Kent; Cobarruvias, John; Piplani, Perry J.; Busa, Joel

2009-01-01

Digital Camera Control Software (DCCS) is a computer program for controlling a boom and a boom-mounted camera used to inspect the external surface of a space shuttle in orbit around the Earth. Running in a laptop computer in the space-shuttle crew cabin, DCCS commands integrated displays and controls. By means of a simple one-button command, a crewmember can view low- resolution images to quickly spot problem areas and can then cause a rapid transition to high- resolution images. The crewmember can command that camera settings apply to a specific small area of interest within the field of view of the camera so as to maximize image quality within that area. DCCS also provides critical high-resolution images to a ground screening team, which analyzes the images to assess damage (if any); in so doing, DCCS enables the team to clear initially suspect areas more quickly than would otherwise be possible and further saves time by minimizing the probability of re-imaging of areas already inspected. On the basis of experience with a previous version (2.0) of the software, the present version (3.0) incorporates a number of advanced imaging features that optimize crewmember capability and efficiency.

Nuclear Technology. Course 30: Mechanical Inspection. Module 30-6, Protective Coating Inspection.

ERIC Educational Resources Information Center

Espy, John

This sixth in a series of eight modules for a course titled Mechanical Inspection describes the duties of the nuclear quality assurance/quality control technician that are associated with protective coatings, and the national standards that govern the selection, application, and inspection of protective coatings for the reactor containment…

Nuclear Technology. Course 30: Mechanical Inspection. Module 30-1, Pump Inspection.

ERIC Educational Resources Information Center

Wasil, Ed; Espy, John

This first in a series of eight modules for a course titled Mechanical Inspection describes the type of pumps used in nuclear power plant systems, the basic operating principles of each type, and the inspection activities performed by the quality assurance/quality control technician. The module follows a typical format that includes the following…

Application of Statistical Quality Control Techniques to Detonator Fabrication: Feasibility Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, J. Frank

1971-05-20

A feasibility study was performed on the use of process control techniques which might reduce the need for a duplicate inspection by production inspection and quality control inspection. Two active detonator fabrication programs were selected for the study. Inspection areas accounting for the greatest percentage of total inspection costs were selected by applying "Pareto's Principle of Maldistribution." Data from these areas were then gathered and analyzed by a process capabiltiy study.

Quality inspection of anisotropic scintillating lead tungstate (PbWO 4) crystals through measurement of interferometric fringe pattern parameters

NASA Astrophysics Data System (ADS)

Cocozzella, N.; Lebeau, M.; Majni, G.; Paone, N.; Rinaldi, D.

2001-08-01

Scintillating crystals are widely used as detectors in radiographic systems, computerized axial tomography devices and in calorimeters employed in high-energy physics. This paper results from a project motivated by the development of the CMS calorimeter at CERN, which will make use of a large number of scintillating crystals. In order to prevent crystals from breaking because of internal residual stress, a quality control system based on optic inspection of interference fringe patterns was developed. The principle of measurement procedures was theoretically modelled, and then a dedicated polariscope was designed and built, in order to observe the crystals under induced stresses or to evaluate the residual internal stresses. The results are innovative and open a new perspective for scintillating crystals quality control: the photoelastic constant normal to the optic axis of the lead tungstate crystals (PbWO 4) was measured, and the inspection procedure developed is applicable to mass production, not only to optimize the crystal processing, but also to establish a quality inspection procedure.

Quality Leadership and Quality Control

PubMed Central

Badrick, Tony

2003-01-01

Different quality control rules detect different analytical errors with varying levels of efficiency depending on the type of error present, its prevalence and the number of observations. The efficiency of a rule can be gauged by inspection of a power function graph. Control rules are only part of a process and not an end in itself; just as important are the trouble-shooting systems employed when a failure occurs. 'Average of patient normals' may develop as a usual adjunct to conventional quality control serum based programmes. Acceptable error can be based on various criteria; biological variation is probably the most sensible. Once determined, acceptable error can be used as limits in quality control rule systems. A key aspect of an organisation is leadership, which links the various components of the quality system. Leadership is difficult to characterise but its key aspects include trust, setting an example, developing staff and critically setting the vision for the organisation. Organisations also have internal characteristics such as the degree of formalisation, centralisation, and complexity. Medical organisations can have internal tensions because of the dichotomy between the bureaucratic and the shadow medical structures. PMID:18568046

48 CFR 552.246-70 - Source Inspection by Quality Approved Manufacturer.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (Quality Management Systems—Requirements). A documented description of the inspection system shall be made... inspections or tests of materials and components before incorporation into end articles and for inspection of such end articles before shipment. When the manufacturing plant is located outside of the United States...

Using Inspections to Improve the Quality of Product Documentation and Code.

ERIC Educational Resources Information Center

Zuchero, John

1995-01-01

Describes how, by adapting software inspections to assess documentation and code, technical writers can collaborate with development personnel, editors, and customers to dramatically improve both the quality of documentation and the very process of inspecting that documentation. Notes that the five steps involved in the inspection process are:…

Scaled multisensor inspection of extended surfaces for industrial quality control

NASA Astrophysics Data System (ADS)

Kayser, Daniel; Bothe, Thorsten; Osten, Wolfgang

2002-06-01

Reliable real-time surface inspection of extended surfaces with high resolution is needed in several industrial applications. With respect to an efficient application to extended technical components such as aircraft or automotive parts, the inspection system has to perform a robust measurement with a ratio of less then 10-6 between depth resolution and lateral extension. This ratio is at least one order beyond the solutions that are offered by existing technologies. The concept of scaled topometry consists of arranging different optical measurement techniques with overlapping ranges of resolution systematically in order to receive characteristic surface information with the required accuracy. In such a surface inspection system, an active algorithm combines measurements on several scales of resolution and distinguishes between local fault indicating structures with different extensions and global geometric properties. The first part of this active algorithm finds indications of critical surface areas in the data of every measurement and separates them into different categories. The second part analyses the detected structures in the data with respect to their resolution and decides whether a further local measurement with a higher resolution has to be performed. The third part positions the sensors and starts the refined measurements. The fourth part finally integrates the measured local data set into the overall data mesh. We have constructed a laboratory setup capable of measuring surfaces with extensions up to 1500mm x 1000mm x 500mm (in x-, y- and z-direction respectively). Using this measurement system we will be able to separate the fault indicating structures on the surface from the global shape and to classify the detected structures according to their extensions and characteristic shapes simultaneously. The level of fault detection probability will be applicable by input parameter control.

[Application of laboratory information system in the management of the key indicators of quality inspection].

PubMed

Guo, Ye; Chen, Qian; Wu, Wei; Cui, Wei

2015-03-31

To establish a system of monitoring the key indicator of quality for inspection (KIQI) on a laboratory information system (LIS), and to have a better management of KIQI. Clinical sample made in PUMCH were collected during the whole of 2014. Next, interactive input program were designed to accomplish data collecting of the disqualification rate of samples, the mistake rate of samples and the occasions of losing samples, etc. Then, a series moment of sample collection, laboratory sample arrived, sample test, sample check, response to critical value, namely, trajectory information left on LIS were recorded and the qualification rate of TAT, the notification rate of endangering result were calculated. Finally, the information about quality control were collected to build an internal quality control database and the KIQI, such as the out-of-control rate of quality control and the total error of test items were monitored. The inspection of the sample management shows the disqualification rates in 2014 were all below the target, but the rates in January and February were a little high and the rates of four wards were above 2%. The mistake rates of samples was 0.47 cases/10 000 cases, attaining the target (< 2 cases/10 000 cases). Also, there was no occasion of losing samples in 2014, attaining the target too. The inspection of laboratory reports shows the qualification rates of TAT was within the acceptable range (> 95%), however the rates of blood routine in November (94.75%) was out of range. We have solved the problem by optimizing the processes. The notification rate of endangering result attained the target (≥ 98%), while the rate of timely notification is needed to improve. Quality inspection shows the CV of APTT in August (5.02%) was rising significantly, beyond the accepted CV (5.0%). We have solved the problem by changing the reagent. The CV of TT in 2014 were all below the allowable CV, thus the allowable CV of the next year lower to 10%. It is an objective

Quality control process improvement of flexible printed circuit board by FMEA

NASA Astrophysics Data System (ADS)

Krasaephol, Siwaporn; Chutima, Parames

2018-02-01

This research focuses on the quality control process improvement of Flexible Printed Circuit Board (FPCB), centred around model 7-Flex, by using Failure Mode and Effect Analysis (FMEA) method to decrease proportion of defective finished goods that are found at the final inspection process. Due to a number of defective units that were found at the final inspection process, high scraps may be escaped to customers. The problem comes from poor quality control process which is not efficient enough to filter defective products from in-process because there is no In-Process Quality Control (IPQC) or sampling inspection in the process. Therefore, the quality control process has to be improved by setting inspection gates and IPCQs at critical processes in order to filter the defective products. The critical processes are analysed by the FMEA method. IPQC is used for detecting defective products and reducing chances of defective finished goods escaped to the customers. Reducing proportion of defective finished goods also decreases scrap cost because finished goods incur higher scrap cost than work in-process. Moreover, defective products that are found during process can reflect the abnormal processes; therefore, engineers and operators should timely solve the problems. Improved quality control was implemented for 7-Flex production lines from July 2017 to September 2017. The result shows decreasing of the average proportion of defective finished goods and the average of Customer Manufacturers Lot Reject Rate (%LRR of CMs) equal to 4.5% and 4.1% respectively. Furthermore, cost saving of this quality control process equals to 100K Baht.

Fault-Tolerant Control For A Robotic Inspection System

NASA Technical Reports Server (NTRS)

Tso, Kam Sing

1995-01-01

Report describes first phase of continuing program of research on fault-tolerant control subsystem of telerobotic visual-inspection system. Goal of program to develop robotic system for remotely controlled visual inspection of structures in outer space.

Adhesive quality inspection of wind rotor blades using thermography

NASA Astrophysics Data System (ADS)

Li, Xiaoli; Sun, Jiangang; Shen, Jingling; Wang, Xun; Zhang, Cunlin; Zhao, Yuejin

2018-04-01

Wind power is playing an increasingly important role in ensuring electrical safety for human beings. Because wind rotor blades are getting larger and larger in order to harvest wind energy more efficiently, there is a growing demand for nondestructive testing. Due to the glue structure of rotor blades, adhesive quality evaluation is needed. In this study, three adhesive samples with a wall thickness of 13mm, 28mm or 31mm were each designed with a different adhesive situation. The transmission thermography was applied to inspect the samples. The results illustrate that this method is effective to inspect adhesive quality of wind rotor blades.

Quality Assurance and Quality Control, Part 2.

PubMed

Akers, Michael J

2015-01-01

The tragedy surrounding the New England Compounding Center and contaminated steroid syringe preparations clearly points out what can happen if quality-assurance and quality-control procedures are not strictly practiced in the compounding of sterile preparations. This article is part 2 of a two-part article on requirements to comply with United States Pharmacopeia general chapters <797> and <1163> with respect to quality assurance of compounded sterile preparations. Part 1 covered documentation requirements, inspection procedures, compounding accuracy checks, and part of a discussion on bacterial endotoxin testing. Part 2 covers sterility testing, the completion from part 1 on bacterial endotoxin testing, a brief dicussion of United States Pharmacopeia <1163>, and advances in pharmaceutical quality systems.

41 CFR 101-27.207 - Control and inspection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Control and inspection... Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 27-INVENTORY MANAGEMENT 27.2-Management of Shelf-Life Materials § 101-27.207 Control and inspection. ...

Examination of the association between announced inspections and inspection scores.

PubMed

Waters, A Blake; VanDerslice, James; Porucznik, Christina A; Kim, Jaewhan; DeLegge, Royal; Durrant, Lynne

2013-09-01

In 2010 the Salt Lake Valley Health Department conducted a pilot of an announced inspection program utilizing a randomized assignment of restaurants to an intervention group with announced inspections and a control group that remained on the usual schedule of unannounced inspections. After adjusting for food type, visible kitchen, outside quality assurance, season, and standardized inspector, significant reductions were found in the odds ratios of personal hygiene (adjusted odds ratios [aOR] = 0.11, p = .00) and equipment cleanliness (aOR = 0.19, p = .00) violations. In the models for the control group, none of the odds ratios were statistically different from one, indicating no change in the postintervention time period as compared to the preintervention period.

Grain quality inspection system

NASA Technical Reports Server (NTRS)

Flood, C. A., Jr.; Singletow, D. P.; James, S. N.

1979-01-01

A review of grain quality indicators and measurement methods was conducted in order to assess the feasibility of using remote sensing technology to develop a continuous monitoring system for use during grain transfer operations. Most detection methods were found to be too slow or too expensive to be incorporated into the normal inspection procedure of a grain elevator on a continuous basis. Two indicators, moisture content and broken corn and foreign material, show potential for automation and are of an economic value. A microprocessor based system which utilizes commercially available electronic moisture meter was developed and tested. A method for automating BCFM measurement is described. A complete system description is presented along with performance test results.

Guidelines for software inspections

NASA Technical Reports Server (NTRS)

1983-01-01

Quality control inspections are software problem finding procedures which provide defect removal as well as improvements in software functionality, maintenance, quality, and development and testing methodology is discussed. The many side benefits include education, documentation, training, and scheduling.

Improving meat inspection and control in resource-poor communities: the Nepal example.

PubMed

Joshi, Durga Datt; Maharjan, Mahendra; Johansen, Maria Vang; Willingham, Arve Lee; Sharma, Minu

2003-06-01

Meat is an important source of protein and a valuable commodity in resource-poor communities. In many developing countries, lack of appropriate slaughtering facilities and unsatisfactory slaughtering techniques are causing unnecessary losses of meat as well as invaluable by-products from animal carcasses. Slaughtering places are frequently contaminated and may not be protected against dogs, rodents and insects. Meat products coming from such conditions are often deteriorated due to bacterial infection or contaminated, which may cause food poisoning or diseases in consumers. In many developing countries, regulations concerning meat inspection and/or control are inadequate or non-existent allowing consumers to be exposed to pathogens including zoonotic parasites. In Nepal, buffaloes contribute about 64% of the meat consumed, followed by goat meat (20%), pork (7%), poultry (6%) and mutton (2%). Goat and poultry meat is acceptable to all castes of people while buffalo meat is consumed mainly by the Newar ethnic group. Previously, pork was consumed only by people belonging to low castes, however, in recent years, the consumption of pork has increased in higher castes as the caste system has become more relaxed. Until recently, there were no official meat inspection regulations in the country, however, in 1999, the national government legislated an as-yet-to-be implemented Animal Slaughtering and Meat Inspection Act which mandates slaughterhouse construction and meat inspection and control. Due to the lack of implementation of the Meat Inspection Act and resultant absence of meat inspection, meat from sick or parasite-infected animals is serving as a source of infection to humans as well as other animals. In addition, meat quality is adversely affected by careless handling conditions in the slaughtering places as well as in the meat markets or shops. For improvement in animal slaughtering and meat inspection in both rural and urban areas of Nepal, several strategies are

Machine vision system: a tool for quality inspection of food and agricultural products.

PubMed

Patel, Krishna Kumar; Kar, A; Jha, S N; Khan, M A

2012-04-01

Quality inspection of food and agricultural produce are difficult and labor intensive. Simultaneously, with increased expectations for food products of high quality and safety standards, the need for accurate, fast and objective quality determination of these characteristics in food products continues to grow. However, these operations generally in India are manual which is costly as well as unreliable because human decision in identifying quality factors such as appearance, flavor, nutrient, texture, etc., is inconsistent, subjective and slow. Machine vision provides one alternative for an automated, non-destructive and cost-effective technique to accomplish these requirements. This inspection approach based on image analysis and processing has found a variety of different applications in the food industry. Considerable research has highlighted its potential for the inspection and grading of fruits and vegetables, grain quality and characteristic examination and quality evaluation of other food products like bakery products, pizza, cheese, and noodles etc. The objective of this paper is to provide in depth introduction of machine vision system, its components and recent work reported on food and agricultural produce.

Food Safety and Quality. Uniform, Risk-Based Inspection System Needed to Ensure Safe Food Supply,

DTIC Science & Technology

1992-06-01

Concerned about the effectiveness of the federal food safety inspection system, the Chairman, Subcommittee on Oversight and Investigations, House...federal resources for inspection, and (3) agencies are effectively coordinating their food safety and quality inspection efforts.

30 CFR 77.1004 - Ground control; inspection and maintenance; general.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Ground control; inspection and maintenance... OF UNDERGROUND COAL MINES Ground Control § 77.1004 Ground control; inspection and maintenance... unsafe ground conditions shall be corrected promptly, or the area shall be posted. ...

30 CFR 77.1004 - Ground control; inspection and maintenance; general.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Ground control; inspection and maintenance... OF UNDERGROUND COAL MINES Ground Control § 77.1004 Ground control; inspection and maintenance... unsafe ground conditions shall be corrected promptly, or the area shall be posted. ...

Developing an App by Exploiting Web-Based Mobile Technology to Inspect Controlled Substances in Patient Care Units

PubMed Central

2017-01-01

We selected iOS in this study as the App operation system, Objective-C as the programming language, and Oracle as the database to develop an App to inspect controlled substances in patient care units. Using a web-enabled smartphone, pharmacist inspection can be performed on site and the inspection result can be directly recorded into HIS through the Internet, so human error of data translation can be minimized and the work efficiency and data processing can be improved. This system not only is fast and convenient compared to the conventional paperwork, but also provides data security and accuracy. In addition, there are several features to increase inspecting quality: (1) accuracy of drug appearance, (2) foolproof mechanism to avoid input errors or miss, (3) automatic data conversion without human judgments, (4) online alarm of expiry date, and (5) instant inspection result to show not meted items. This study has successfully turned paper-based medication inspection into inspection using a web-based mobile device. PMID:28286761

Developing an App by Exploiting Web-Based Mobile Technology to Inspect Controlled Substances in Patient Care Units.

PubMed

Lu, Ying-Hao; Lee, Li-Yao; Chen, Ying-Lan; Cheng, Hsing-I; Tsai, Wen-Tsung; Kuo, Chen-Chun; Chen, Chung-Yu; Huang, Yaw-Bin

2017-01-01

We selected iOS in this study as the App operation system, Objective-C as the programming language, and Oracle as the database to develop an App to inspect controlled substances in patient care units. Using a web-enabled smartphone, pharmacist inspection can be performed on site and the inspection result can be directly recorded into HIS through the Internet, so human error of data translation can be minimized and the work efficiency and data processing can be improved. This system not only is fast and convenient compared to the conventional paperwork, but also provides data security and accuracy. In addition, there are several features to increase inspecting quality: (1) accuracy of drug appearance, (2) foolproof mechanism to avoid input errors or miss, (3) automatic data conversion without human judgments, (4) online alarm of expiry date, and (5) instant inspection result to show not meted items. This study has successfully turned paper-based medication inspection into inspection using a web-based mobile device.

Grade pending: lessons for hospital quality reporting from the New York City restaurant sanitation inspection program.

PubMed

Ryan, Andrew M; Detsky, Allan S

2015-02-01

Public quality reporting programs have been widely implemented in hospitals in an effort to improve quality and safety. One such program is Hospital Compare, Medicare's national quality reporting program for US hospitals. The New York City sanitary grade inspection program is a parallel effort for restaurants. The aims of Hospital Compare and the New York City sanitary inspection program are fundamentally similar: to address a common market failure resulting from consumers' lack of information on quality and safety. However, by displaying easily understandable information at the point of service, the New York City sanitary inspection program is better designed to encourage informed consumer decision making. We argue that this program holds important lessons for public quality reporting of US hospitals. © 2014 Society of Hospital Medicine.

Low-Cost Quality Control and Nondestructive Evaluation Technologies for General Aviation Structures

NASA Technical Reports Server (NTRS)

Cramer, K. Elliott; Gavinsky, Bob; Semanskee, Grant

1998-01-01

NASA's Advanced General Aviation Transport Experiments (AGATE) Program has as a goal to reduce the overall cost of producing private aviation aircraft while maintaining the safety of these aircraft. In order to successfully meet this goal, it is necessary to develop nondestructive inspection techniques which will facilitate the production of the materials used in these aircraft and assure the quality necessary to maintain airworthiness. This paper will discuss a particular class of general aviation materials and several nondestructive inspection techniques that have proven effective for making these inspections. Additionally, this paper will discuss the investigation and application of other commercially available quality control techniques applicable to these structures.

Manufacture and quality control of interconnecting wire hardnesses, Volume 1

NASA Technical Reports Server (NTRS)

1972-01-01

A standard is presented for manufacture, installation, and quality control of eight types of interconnecting wire harnesses. The processes, process controls, and inspection and test requirements reflected are based on acknowledgment of harness design requirements, acknowledgment of harness installation requirements, identification of the various parts, materials, etc., utilized in harness manufacture, and formulation of a typical manufacturing flow diagram for identification of each manufacturing and quality control process, operation, inspection, and test. The document covers interconnecting wire harnesses defined in the design standard, including type 1, enclosed in fluorocarbon elastomer convolute, tubing; type 2, enclosed in TFE convolute tubing lines with fiberglass braid; type 3, enclosed in TFE convolute tubing; and type 5, combination of types 3 and 4. Knowledge gained through experience on the Saturn 5 program coupled with recent advances in techniques, materials, and processes was incorporated.

Perceptions of Physical Inspections as a Tool to Protect Housing Quality and Promote Health Equity.

PubMed

Holtzen, Holly; Klein, Elizabeth G; Keller, Brittney; Hood, Nancy

2016-01-01

Physical inspections that assess how well affordable housing properties meet quality and safety standards help to ensure that low-income tenants live in a healthy built environment. This study was part of a larger Health Impact Assessment (HIA) conducted between January 2012 and November 2013 to inform policymakers about the potential health consequences of a proposed policy decision to align the physical inspections required by housing funding agencies, which would result in a reduction of the frequency of physical inspections. Key informant interviews (n=18) of property managers and tenants were used to explore the inspection process, identification of housing quality issues, and potential effects on the health of affordable housing tenants and the impact on property management practices. Results indicate that physical inspection frequency may be an important trigger for property managers and tenants to adhere to proper maintenance schedules.

Continuous integration and quality control for scientific software

NASA Astrophysics Data System (ADS)

Neidhardt, A.; Ettl, M.; Brisken, W.; Dassing, R.

2013-08-01

Modern software has to be stable, portable, fast and reliable. This is going to be also more and more important for scientific software. But this requires a sophisticated way to inspect, check and evaluate the quality of source code with a suitable, automated infrastructure. A centralized server with a software repository and a version control system is one essential part, to manage the code basis and to control the different development versions. While each project can be compiled separately, the whole code basis can also be compiled with one central “Makefile”. This is used to create automated, nightly builds. Additionally all sources are inspected automatically with static code analysis and inspection tools, which check well-none error situations, memory and resource leaks, performance issues, or style issues. In combination with an automatic documentation generator it is possible to create the developer documentation directly from the code and the inline comments. All reports and generated information are presented as HTML page on a Web server. Because this environment increased the stability and quality of the software of the Geodetic Observatory Wettzell tremendously, it is now also available for scientific communities. One regular customer is already the developer group of the DiFX software correlator project.

Inspecting School Social Quality: Assessing and Improving School Effectiveness in the Social Domain

ERIC Educational Resources Information Center

Dijkstra, Anne Bert; Daas, Remmert; De la Motte, Per Ingvar; Ehren, Melanie

2017-01-01

Purpose: School inspection of school social quality is, in contrast to inspection in the cognitive domain, still in its early phase of development. While schools are shown to affect social outcomes, the interplay of mechanisms makes it difficult to isolate the effect of the school. This paper aims to evaluate different approaches to inspecting…

ProSens: integrated production control by automated inspection planning and efficient multisensor metrology

NASA Astrophysics Data System (ADS)

Glaser, Ulf; Li, Zhichao; Bichmann, Stephan, II; Pfeifer, Tilo

2003-05-01

By China's entry into the WTO, Chinese as well as German companies are facing the question, how to minimize the risk of unfamiliar cooperation partners when developing products. The rise of customer demands concerning quality, product diversity and the reduction of expenses require flexibility and efficiency with reliable component suppliers. In order to build and strengthen sino-german cooperations, a manufacturing control using homogenized and efficient measures to assure high quality is of vital importance. Lack of unifications may cause identical measurements conducted at subcontractors or customers to be carried out with different measurement processes which leads to incomparable results. Rapidly growing company cooperations and simultaneously decreasing of manufacturing scope cause substantial difficulties when coordinating joint quality control activities. "ProSens," a sino-german project consortium consisting of industrial users, technology producers and research institutes, aims at improving selected production processes by: Creation of a homogeneous quality awareness in sino-german cooperations. Sensitization for process accompanying metrology at an early stage of product development. Increase of the process performance by the use of integrated metrology. Reduction of production time and cost. Unification of quality control of complex products by means of efficient measurement strategies and CAD-based inspection planning.

[Quality control of Maca (Lepidium meyenii)].

PubMed

Shu, Ji-cheng; Cui, Hang-qing; Huang, Ying-zheng; Huang, Xiao-ying; Yang, Ming

2015-12-01

To control the quality of Maca, the quality standard was established in this study. According to the methods recorded in the Appendix of Chinese Pharmacopoeia (2010 Edition), the water, extract, total ash, acid insoluble substance, and heavy metals inspections in Lepidium meyenii were carried out. N-benzyl-9Z, 12Z-octadecadienamide in L. meyenii was identified by TLC, and it was determined by HPLC. The results showed that the N-benzyl-9Z, 12Z-octadecadienamide identification of TLC was a strong mark and specificity. In content determination experiment, the linearity of N-benzyl-9Z, 12Z-octadecadienamide was in the range of 0.01-2 microg (r = 0.9998), and the average recovery (n=9) was 99.27% (RSD 2.0%). The methods were simple, accurate, with good reproducibility. It is suitable for quality control L. meyenii.

Quality control of fireproof coatings for reinforced concrete structures

NASA Astrophysics Data System (ADS)

Gravit, Marina; Dmitriev, Ivan; Ishkov, Alexander

2017-10-01

The article analyzes methods of quality inspection of fireproof coatings (work flow, measuring, laboratory, etc.). In modern construction there is a problem of lack of distinct monitoring for the fire protection testing. There is a description of this testing for reinforced concrete structures. The article shows the results of calculation quality control of hatches as an example of fireproof coating for reinforced concrete structures.

Intelligent Monitoring? Assessing the ability of the Care Quality Commission's statistical surveillance tool to predict quality and prioritise NHS hospital inspections.

PubMed

Griffiths, Alex; Beaussier, Anne-Laure; Demeritt, David; Rothstein, Henry

2017-02-01

The Care Quality Commission (CQC) is responsible for ensuring the quality of the health and social care delivered by more than 30 000 registered providers in England. With only limited resources for conducting on-site inspections, the CQC has used statistical surveillance tools to help it identify which providers it should prioritise for inspection. In the face of planned funding cuts, the CQC plans to put more reliance on statistical surveillance tools to assess risks to quality and prioritise inspections accordingly. To evaluate the ability of the CQC's latest surveillance tool, Intelligent Monitoring (IM), to predict the quality of care provided by National Health Service (NHS) hospital trusts so that those at greatest risk of providing poor-quality care can be identified and targeted for inspection. The predictive ability of the IM tool is evaluated through regression analyses and χ 2 testing of the relationship between the quantitative risk score generated by the IM tool and the subsequent quality rating awarded following detailed on-site inspection by large expert teams of inspectors. First, the continuous risk scores generated by the CQC's IM statistical surveillance tool cannot predict inspection-based quality ratings of NHS hospital trusts (OR 0.38 (0.14 to 1.05) for Outstanding/Good, OR 0.94 (0.80 to -1.10) for Good/Requires improvement, and OR 0.90 (0.76 to 1.07) for Requires improvement/Inadequate). Second, the risk scores cannot be used more simply to distinguish the trusts performing poorly-those subsequently rated either 'Requires improvement' or 'Inadequate'-from the trusts performing well-those subsequently rated either 'Good' or 'Outstanding' (OR 1.07 (0.91 to 1.26)). Classifying CQC's risk bandings 1-3 as high risk and 4-6 as low risk, 11 of the high risk trusts were performing well and 43 of the low risk trusts were performing poorly, resulting in an overall accuracy rate of 47.6%. Third, the risk scores cannot be used even more simply to

Vision Based Autonomous Robotic Control for Advanced Inspection and Repair

NASA Technical Reports Server (NTRS)

Wehner, Walter S.

2014-01-01

The advanced inspection system is an autonomous control and analysis system that improves the inspection and remediation operations for ground and surface systems. It uses optical imaging technology with intelligent computer vision algorithms to analyze physical features of the real-world environment to make decisions and learn from experience. The advanced inspection system plans to control a robotic manipulator arm, an unmanned ground vehicle and cameras remotely, automatically and autonomously. There are many computer vision, image processing and machine learning techniques available as open source for using vision as a sensory feedback in decision-making and autonomous robotic movement. My responsibilities for the advanced inspection system are to create a software architecture that integrates and provides a framework for all the different subsystem components; identify open-source algorithms and techniques; and integrate robot hardware.

48 CFR 846.408-70 - Inspection of subsistence.

Code of Federal Regulations, 2010 CFR

2010-10-01

... inspect for specification compliance before shipment; or (2) Personnel of the purchasing activity will... suppliers' own quality control system. (3) Experience with the proposed suppliers. (4) The pre-qualifying of... address where inspection will occur. (e) The contracting officer must furnish a copy of the purchase...

Food quality inspection by speckle decorrelation properties of bacteria colonies

NASA Astrophysics Data System (ADS)

Bianco, V.; Mandracchia, B.; Nazzaro, F.; Marchesano, V.; Gennari, O.; Paturzo, M.; Grilli, S.; Ferraro, P.

2017-06-01

The development of tools for rapid food quality inspection is a highly pursued goal. These could be valuable devices to be used by food producers in factories or the customers themselves in specific installations at the marketplace. Here we show how speckle patterns in coherent imaging systems can be can be employed as indicators of the presence of bacteria colonies contaminating food or water. Speckle decorrelation is induced by the self-propelling movement of these organisms when they interact with coherent light. Hence, their presence can be detected using a simple setup in a condition in which the single element cannot be imaged, but the properties of the ensemble can be exploited. Thanks to the small magnification factor we set, our system can inspect a large Field-of-View (FoV). We show the possibility to discriminate between fresh and contaminated food, thus paving the way to the rapid food quality testing by consumers at the marketplace.

A Bevel Gear Quality Inspection System Based on Multi-Camera Vision Technology.

PubMed

Liu, Ruiling; Zhong, Dexing; Lyu, Hongqiang; Han, Jiuqiang

2016-08-25

Surface defect detection and dimension measurement of automotive bevel gears by manual inspection are costly, inefficient, low speed and low accuracy. In order to solve these problems, a synthetic bevel gear quality inspection system based on multi-camera vision technology is developed. The system can detect surface defects and measure gear dimensions simultaneously. Three efficient algorithms named Neighborhood Average Difference (NAD), Circle Approximation Method (CAM) and Fast Rotation-Position (FRP) are proposed. The system can detect knock damage, cracks, scratches, dents, gibbosity or repeated cutting of the spline, etc. The smallest detectable defect is 0.4 mm × 0.4 mm and the precision of dimension measurement is about 40-50 μm. One inspection process takes no more than 1.3 s. Both precision and speed meet the requirements of real-time online inspection in bevel gear production.

A Bevel Gear Quality Inspection System Based on Multi-Camera Vision Technology

PubMed Central

Liu, Ruiling; Zhong, Dexing; Lyu, Hongqiang; Han, Jiuqiang

2016-01-01

Surface defect detection and dimension measurement of automotive bevel gears by manual inspection are costly, inefficient, low speed and low accuracy. In order to solve these problems, a synthetic bevel gear quality inspection system based on multi-camera vision technology is developed. The system can detect surface defects and measure gear dimensions simultaneously. Three efficient algorithms named Neighborhood Average Difference (NAD), Circle Approximation Method (CAM) and Fast Rotation-Position (FRP) are proposed. The system can detect knock damage, cracks, scratches, dents, gibbosity or repeated cutting of the spline, etc. The smallest detectable defect is 0.4 mm × 0.4 mm and the precision of dimension measurement is about 40–50 μm. One inspection process takes no more than 1.3 s. Both precision and speed meet the requirements of real-time online inspection in bevel gear production. PMID:27571078

Control Of A Serpentine Robot For Inspection Tasks

NASA Technical Reports Server (NTRS)

Seraji, Homayoun; Colbaugh, Richard D.; Glass, Kristin L.

1996-01-01

Efficient, robust kinematic control scheme developed to control serpentine robot designed to inspect complex structure. Takes full advantage of multiple redundant degrees of freedom of robot to provide considerable dexterity for maneuvering through workspace cluttered with stationary obstacles at initially unknown positions. Control scheme produces slithering motion.

Thermodynamic inspection of concrete using a controlled heat source

NASA Astrophysics Data System (ADS)

Milne, James M.

1990-10-01

Concrete is not quite such a non-destructable material as many are led to believe. It can deteriorate with time due to changes in the chemistry, the effect of moisture penetration and the corrosion of reinforcing steel bars. Much of this damage occurs relatively close to the surface, sometimes revealed by discolourations or the presence of cracks and sometimes as spallation when the corrosion products of steel cause delamination of the near surface concrete. These effects may occur in good quality concrete but their severity and rapidity of onset may be enhanced by fabrication defects when aggregates may not be to specification or the packing conditions cause porosity. It may thus be months or even years afterwards that these defects come to light. As a consequence a new industry has been formed to inspect concrete structures which may include X-ray equipment, linac accelerators, gamma isotope sources, ultrasonics, radar and of course thermography. Each of these nethods will have their own particular attractive features and merits. But most of these activities tend to be used more as a "fire fighting" service than as one ensuring regular maintenance of critical structures or even as quality control of structures during building. Quite often it seems that Non-destructive Testing is turned into a litigation service for dissatisfied customers and thermography is no stranger to this topic. It is heartening to see that the ASTM organisation in the USA and British Standards are encouraging and developing suitable standards for the inspection of concrete by thermographic techniques.

Flexible optical metrology strategies for the control and quality assurance of small series production

NASA Astrophysics Data System (ADS)

Schmitt, R.; Pavim, A.

2009-06-01

The demand for achieving smaller and more flexible production series with a considerable diversity of products complicates the control of the manufacturing tasks, leading to big challenges for the quality assurance systems. The quality assurance strategy that is nowadays used for mass production is unable to cope with the inspection flexibility needed among automated small series production, because the measuring strategy is totally dependent on the fixed features of the few manufactured object variants and on process parameters that can be controlled/compensated during production time. The major challenge faced by a quality assurance system applied to small series production facilities is to guarantee the needed quality level already at the first run, and therefore, the quality assurance system has to adapt itself constantly to the new manufacturing conditions. The small series production culture requires a change of paradigms, because its strategies are totally different from mass production. This work discusses the tight inspection requirements of small series production and presents flexible metrology strategies based on optical sensor data fusion techniques, agent-based systems as well as cognitive and self-optimised systems for assuring the needed quality level of flexible small series. Examples of application scenarios are provided among the automated assembly of solid state lasers and the flexible inspection of automotive headlights.

46 CFR 160.064-6 - Examinations, tests and inspections.

Code of Federal Regulations, 2010 CFR

2010-10-01

... labeled water safety buoyant devices shall maintain quality control of the materials used, manufacturing... available to the recognized laboratory inspector or to the Coast Guard marine inspector, or both, for review upon request. (b) Laboratory inspections and tests. Such examinations, inspections and tests as are...

Surface and subsurface inspection of food safety and quality using a line-scan Raman system

USDA-ARS?s Scientific Manuscript database

This paper presents a line-scan Raman platform for food safety and quality research, which can be configured for Raman chemical imaging (RCI) mode for surface inspection and spatially offset Raman spectroscopy (SORS) mode for subsurface inspection. In the RCI mode, macro-scale imaging was achieved u...

21 CFR 820.72 - Inspection, measuring, and test equipment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Inspection, measuring, and test equipment. 820.72 Section 820.72 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES QUALITY SYSTEM REGULATION Production and Process Controls § 820.72 Inspection...

Application of color mixing for safety and quality inspection of agricultural products

NASA Astrophysics Data System (ADS)

Ding, Fujian; Chen, Yud-Ren; Chao, Kuanglin

2005-11-01

In this paper, color-mixing applications for food safety and quality was studied, including two-color mixing and three-color mixing. It was shown that the chromaticness of the visual signal resulting from two- or three-color mixing is directly related to the band ratio of light intensity at the two or three selected wavebands. An optical visual device using color mixing to implement the band ratio criterion was presented. Inspection through human vision assisted by an optical device that implements the band ratio criterion would offer flexibility and significant cost savings as compared to inspection with a multispectral machine vision system that implements the same criterion. Example applications of this optical color mixing technique were given for the inspection of chicken carcasses with various diseases and for the detection of chilling injury in cucumbers. Simulation results showed that discrimination by chromaticness that has a direct relation with band ratio can work very well with proper selection of the two or three narrow wavebands. This novel color mixing technique for visual inspection can be implemented on visual devices for a variety of applications, ranging from target detection to food safety inspection.

40 CFR 60.2141 - By what date must I conduct the initial air pollution control device inspection?

Code of Federal Regulations, 2011 CFR

2011-07-01

... air pollution control device inspection? 60.2141 Section 60.2141 Protection of Environment... initial air pollution control device inspection? (a) The initial air pollution control device inspection... startup. (b) Within 10 operating days following an air pollution control device inspection, all necessary...

40 CFR 60.2141 - By what date must I conduct the initial air pollution control device inspection?

Code of Federal Regulations, 2012 CFR

2012-07-01

... air pollution control device inspection? 60.2141 Section 60.2141 Protection of Environment... initial air pollution control device inspection? (a) The initial air pollution control device inspection... startup. (b) Within 10 operating days following an air pollution control device inspection, all necessary...

Nuclear Technology. Course 28: Welding Inspection. Module 28-1, Welding Fundamentals and Processes.

ERIC Educational Resources Information Center

Espy, John

This first in a series of ten modules for a course titled Welding Inspection describes the role and responsbilities of the quality assurance/quality control technician in welding inspections. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4) notes to…

Machine Vision-Based Measurement Systems for Fruit and Vegetable Quality Control in Postharvest.

PubMed

Blasco, José; Munera, Sandra; Aleixos, Nuria; Cubero, Sergio; Molto, Enrique

Individual items of any agricultural commodity are different from each other in terms of colour, shape or size. Furthermore, as they are living thing, they change their quality attributes over time, thereby making the development of accurate automatic inspection machines a challenging task. Machine vision-based systems and new optical technologies make it feasible to create non-destructive control and monitoring tools for quality assessment to ensure adequate accomplishment of food standards. Such systems are much faster than any manual non-destructive examination of fruit and vegetable quality, thus allowing the whole production to be inspected with objective and repeatable criteria. Moreover, current technology makes it possible to inspect the fruit in spectral ranges beyond the sensibility of the human eye, for instance in the ultraviolet and near-infrared regions. Machine vision-based applications require the use of multiple technologies and knowledge, ranging from those related to image acquisition (illumination, cameras, etc.) to the development of algorithms for spectral image analysis. Machine vision-based systems for inspecting fruit and vegetables are targeted towards different purposes, from in-line sorting into commercial categories to the detection of contaminants or the distribution of specific chemical compounds on the product's surface. This chapter summarises the current state of the art in these techniques, starting with systems based on colour images for the inspection of conventional colour, shape or external defects and then goes on to consider recent developments in spectral image analysis for internal quality assessment or contaminant detection.

Household indoor air quality and its associations with childhood asthma in Shanghai, China: On-site inspected methods and preliminary results.

PubMed

Huang, Chen; Wang, Xueying; Liu, Wei; Cai, Jiao; Shen, Li; Zou, Zhijun; Lu, Rongchun; Chang, Jing; Wei, Xiaoyang; Sun, Chanjuan; Zhao, Zhuohui; Sun, Yuexia; Sundell, Jan

2016-11-01

Few studies were conducted for associations of home environment with childhood health by on-site inspection in China. During 2013-2014, we conducted a case-control study with home inspection among 454 children (186 asthma children and 268 non-asthma children) in Shanghai, China. In this paper, we detailedly described the inspected methods and analyzed the preliminarily collected data. Except in winter, most residences meet the national standard for indoor temperature and relative humidity. Most living rooms had ≤1000ppm CO 2 , whereas over half of the child's bedrooms had slightly >1000ppm CO 2 during night. Most residences had notably lower than 2500cfu/m 3 airborne culturable fungi and ≤100μg/m 3 formaldehyde. More than 70% of the child's bedrooms had ≤75μg/m 3 PM 2.5 and ≤150μg/m 3 PM 10 . Indoor and outdoor concentrations of particulate matters had strong linear correlations (r=0.891-0.922; p-value <0.001). Most differences between cases and controls were not significant with respect to CO 2 , culturable fungi, formaldehyde, and particulate matters. Before and after adjusted for potential confounders, indoor averaged concentration of CO 2 and particulate matters generally had negative associations with childhood history of doctor-diagnosed asthma in spring, summer, and autumn. Only in winter, indoor CO 2 concentration was significantly associated with the increased odds of childhood asthma. Our results indicated that air quality among most residences in Shanghai could meet the national standard for indoor air quality in warm seasons; but household air quality and ventilation status in winter should be greatly improved. We suspected that those "unexpected" negative associations could exist due to changes in lifestyle behaviors regarding indoor air quality after the child being diagnosed asthma by a doctor. Copyright © 2016 Elsevier Inc. All rights reserved.

Machine vision method for online surface inspection of easy open can ends

NASA Astrophysics Data System (ADS)

Mariño, Perfecto; Pastoriza, Vicente; Santamaría, Miguel

2006-10-01

Easy open can end manufacturing process in the food canning sector currently makes use of a manual, non-destructive testing procedure to guarantee can end repair coating quality. This surface inspection is based on a visual inspection made by human inspectors. Due to the high production rate (100 to 500 ends per minute) only a small part of each lot is verified (statistical sampling), then an automatic, online, inspection system, based on machine vision, has been developed to improve this quality control. The inspection system uses a fuzzy model to make the acceptance/rejection decision for each can end from the information obtained by the vision sensor. In this work, the inspection method is presented. This surface inspection system checks the total production, classifies the ends in agreement with an expert human inspector, supplies interpretability to the operators in order to find out the failure causes and reduce mean time to repair during failures, and allows to modify the minimum can end repair coating quality.

Considerations In The Design And Specifications Of An Automatic Inspection System

NASA Astrophysics Data System (ADS)

Lee, David T.

1980-05-01

Considerable activities have been centered around the automation of manufacturing quality control and inspection functions. Several reasons can be cited for this development. The continuous pressure of direct and indirect labor cost increase is only one of the obvious motivations. With the drive for electronics miniaturization come more and more complex processes where control parameters are critical and the yield is highly susceptible to inadequate process monitor and inspection. With multi-step, multi-layer process for substrate fabrication, process defects that are not detected and corrected at certain critical points may render the entire subassembly useless. As a process becomes more complex, the time required to test the product increases significantly in the total build cycle. The urgency to reduce test time brings more pressure to improve in-process control and inspection. The advances and improvements of components, assemblies and systems such as micro-processors, micro-computers, programmable controllers, and other intelligent devices, have made the automation of quality control much more cost effective and justifiable.

46 CFR 160.047-5 - Inspections and tests. 1

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Inspections and tests. 1 160.047-5 Section 160.047-5... and Child § 160.047-5 Inspections and tests. 1 1 The manufacturer of a personal flotation device must... labeled buoyant vests shall— (1) Maintain quality control of the materials used, the manufacturing methods...

46 CFR 160.047-5 - Inspections and tests. 1

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Inspections and tests. 1 160.047-5 Section 160.047-5... and Child § 160.047-5 Inspections and tests. 1 1 The manufacturer of a personal flotation device must... labeled buoyant vests shall— (1) Maintain quality control of the materials used, the manufacturing methods...

Machine vision based quality inspection of flat glass products

NASA Astrophysics Data System (ADS)

Zauner, G.; Schagerl, M.

2014-03-01

This application paper presents a machine vision solution for the quality inspection of flat glass products. A contact image sensor (CIS) is used to generate digital images of the glass surfaces. The presented machine vision based quality inspection at the end of the production line aims to classify five different glass defect types. The defect images are usually characterized by very little `image structure', i.e. homogeneous regions without distinct image texture. Additionally, these defect images usually consist of only a few pixels. At the same time the appearance of certain defect classes can be very diverse (e.g. water drops). We used simple state-of-the-art image features like histogram-based features (std. deviation, curtosis, skewness), geometric features (form factor/elongation, eccentricity, Hu-moments) and texture features (grey level run length matrix, co-occurrence matrix) to extract defect information. The main contribution of this work now lies in the systematic evaluation of various machine learning algorithms to identify appropriate classification approaches for this specific class of images. In this way, the following machine learning algorithms were compared: decision tree (J48), random forest, JRip rules, naive Bayes, Support Vector Machine (multi class), neural network (multilayer perceptron) and k-Nearest Neighbour. We used a representative image database of 2300 defect images and applied cross validation for evaluation purposes.

(abstract) Formal Inspection Technology Transfer Program

NASA Technical Reports Server (NTRS)

Welz, Linda A.; Kelly, John C.

1993-01-01

A Formal Inspection Technology Transfer Program, based on the inspection process developed by Michael Fagan at IBM, has been developed at JPL. The goal of this program is to support organizations wishing to use Formal Inspections to improve the quality of software and system level engineering products. The Technology Transfer Program provides start-up materials and assistance to help organizations establish their own Formal Inspection program. The course materials and certified instructors associated with the Technology Transfer Program have proven to be effective in classes taught at other NASA centers as well as at JPL. Formal Inspections (NASA tailored Fagan Inspections) are a set of technical reviews whose objective is to increase quality and reduce the cost of software development by detecting and correcting errors early. A primary feature of inspections is the removal of engineering errors before they amplify into larger and more costly problems downstream in the development process. Note that the word 'inspection' is used differently in software than in a manufacturing context. A Formal Inspection is a front-end quality enhancement technique, rather than a task conducted just prior to product shipment for the purpose of sorting defective systems (manufacturing usage). Formal Inspections are supporting and in agreement with the 'total quality' approach being adopted by many NASA centers.

40 CFR 60.2706 - By what date must I conduct the initial air pollution control device inspection?

Code of Federal Regulations, 2012 CFR

2012-07-01

... air pollution control device inspection? 60.2706 Section 60.2706 Protection of Environment... pollution control device inspection? (a) The initial air pollution control device inspection must be... meeting the amended emission limitations. (b) Within 10 operating days following an air pollution control...

40 CFR 60.2706 - By what date must I conduct the initial air pollution control device inspection?

Code of Federal Regulations, 2014 CFR

2014-07-01

... air pollution control device inspection? 60.2706 Section 60.2706 Protection of Environment... pollution control device inspection? (a) The initial air pollution control device inspection must be... meeting the amended emission limitations. (b) Within 10 operating days following an air pollution control...

40 CFR 60.2706 - By what date must I conduct the initial air pollution control device inspection?

Code of Federal Regulations, 2013 CFR

2013-07-01

... air pollution control device inspection? 60.2706 Section 60.2706 Protection of Environment... pollution control device inspection? (a) The initial air pollution control device inspection must be... meeting the amended emission limitations. (b) Within 10 operating days following an air pollution control...

40 CFR 60.2151 - By what date must I conduct the annual air pollution control device inspection?

Code of Federal Regulations, 2011 CFR

2011-07-01

... air pollution control device inspection? 60.2151 Section 60.2151 Protection of Environment... annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution control device inspection), you must complete the air pollution control...

40 CFR 60.2151 - By what date must I conduct the annual air pollution control device inspection?

Code of Federal Regulations, 2012 CFR

2012-07-01

... air pollution control device inspection? 60.2151 Section 60.2151 Protection of Environment... annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution control device inspection), you must complete the air pollution control...

48 CFR 246.472 - Inspection stamping.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality Assurance 246.472 Inspection stamping. (a) DoD quality inspection approval marking designs (stamps) may be used for both prime...) Policies and procedures regarding the use of National Aeronautics and Space Administration (NASA) quality...

Designing a two-rank acceptance sampling plan for quality inspection of geospatial data products

NASA Astrophysics Data System (ADS)

Tong, Xiaohua; Wang, Zhenhua; Xie, Huan; Liang, Dan; Jiang, Zuoqin; Li, Jinchao; Li, Jun

2011-10-01

To address the disadvantages of classical sampling plans designed for traditional industrial products, we originally propose a two-rank acceptance sampling plan (TRASP) for the inspection of geospatial data outputs based on the acceptance quality level (AQL). The first rank sampling plan is to inspect the lot consisting of map sheets, and the second is to inspect the lot consisting of features in an individual map sheet. The TRASP design is formulated as an optimization problem with respect to sample size and acceptance number, which covers two lot size cases. The first case is for a small lot size with nonconformities being modeled by a hypergeometric distribution function, and the second is for a larger lot size with nonconformities being modeled by a Poisson distribution function. The proposed TRASP is illustrated through two empirical case studies. Our analysis demonstrates that: (1) the proposed TRASP provides a general approach for quality inspection of geospatial data outputs consisting of non-uniform items and (2) the proposed acceptance sampling plan based on TRASP performs better than other classical sampling plans. It overcomes the drawbacks of percent sampling, i.e., "strictness for large lot size, toleration for small lot size," and those of a national standard used specifically for industrial outputs, i.e., "lots with different sizes corresponding to the same sampling plan."

Intelligent laser soldering inspection and process control

NASA Technical Reports Server (NTRS)

Vanzetti, Riccardo

1987-01-01

Component assembly on printed circuitry keeps making giant strides toward denser packaging and smaller dimensions. From a single layer to multilayer, from through holes to surface mounted components and tape applied bonds, unrelenting progress results in new, difficult problems in assembling, soldering, inspecting and controlling the manufacturing process of the new electronics. Among the major problems are the variables introduced by human operators. The small dimensions and the tight assembly tolerances are now successfully met by machines which are faster and more precise than the human hand. The same is true for soldering. But visual inspection of the solder joints is now so severely limited by the ever shrinking area accessible to the human eye that the inspector's diagnosis cannot be trusted any longer. Solutions to correcting these problems are discussed.

Application of Motion Induced Remote-Field Eddy-Current effect to online inspection and quality examination of rolling metallic strips

NASA Astrophysics Data System (ADS)

Sun, Yushi; Udpa, Satish; Lord, William; Udpa, Lalita; Ouyang, Tianhe

2001-04-01

The Motion Induced Remote-Field Eddy-Current (MIRFEC) effect was first observed in 1994. The effect was first exploited for detecting pipeline stress corrosion cracks as a part of a research project sponsored by the U.S. Department of Transportation. This paper presents a new application of the MIRFEC effect for online inspection of rolling metallic strips. Currently, rolled metallic strips and sheets are inspected off-line, which is costly, time consuming and not ideal for quality control. A well-designed online diagnostic and control system for metal rolling process may be able to reduce cost, improve quality, and hence enhance competitiveness of the product. The overall objective of this paper is to demonstrate the feasibility of a new nondestructive measurement system for on-line diagnostics and control of metallic rolling process using the MIRFEC effect. The system can be used to monitor, in real time, metallic strips/sheets for possible anomalies, inclusions, voids, bubbles, lamination, as well as variations in its magnetic and other properties. The potential advantages of the MIRFEC system include simplicity, robustness, low cost, high reliability, quick and accurate signal classification and characterization. Such systems can be used for real-time process control, or off-line data analysis. The technique also allows operation at high temperatures, tolerates large lift-off and vibration, and high rolling speed. Results of finite element modeling of the MIRFEC effect and experimental measurement data obtained from a prototype system are presented.

A Steel Ball Surface Quality Inspection Method Based on a Circumferential Eddy Current Array Sensor.

PubMed

Zhang, Huayu; Xie, Fengqin; Cao, Maoyong; Zhong, Mingming

2017-07-01

To efficiently inspect surface defects on steel ball bearings, a new method based on a circumferential eddy current array (CECA) sensor was proposed here. The best probe configuration, in terms of the coil quality factor (Q-factor), magnetic field intensity, and induced eddy current density on the surface of a sample steel ball, was determined using 3-, 4-, 5-, and 6-coil probes, for analysis and comparison. The optimal lift-off from the measured steel ball, the number of probe coils, and the frequency of excitation current suitable for steel ball inspection were obtained. Using the resulting CECA sensor to inspect 46,126 steel balls showed a miss rate of ~0.02%. The sensor was inspected for surface defects as small as 0.05 mm in width and 0.1 mm in depth.

Good clinical practice regulatory inspections: Lessons for Indian investigator sites

PubMed Central

Marwah, R.; Van de Voorde, K.; Parchman, J.

2010-01-01

Regulatory inspections are important to evaluate the integrity of the data submitted to health authorities (HAs), protect patient safety, and assess adequacy of site/sponsor quality systems to achieve the same. Inspections generally occur after submission of data for marketing approval of an investigational drug. In recent years, there has been a significant increase in number of inspections by different HAs, including in India. The assessors/inspectors generally do a thorough review of site data before inspections. All aspects of ICH-GCP, site infrastructure, and quality control systems are assessed during the inspection. Findings are discussed during the close out meeting and a detailed inspection report issued afterward, which has to be responded to within 15–30 days with effective Corrective and Preventive Action Plan (CAPA). Protocol noncompliance, inadequate/inaccurate records, inadequate drug accountability, informed consent issues, and adverse event reporting were some of the most common findings observed during recent Food and Drug Administration (FDA) inspections. Drug development is being increasingly globalized and an increased number of patients enrolled in studies submitted as part of applications come from all over the world including India. Because of the steep increase in research activity in the country, inexperienced sites, and more stakeholders, increased efforts will be required to ensure continuous quality and compliance. HAs have also made clear that enforcement will be increased and be swift, aggressive, and effective. PMID:21350732

Additive Manufacturing Infrared Inspection

NASA Technical Reports Server (NTRS)

Gaddy, Darrell; Nettles, Mindy

2015-01-01

The Additive Manufacturing Infrared Inspection Task started the development of a real-time dimensional inspection technique and digital quality record for the additive manufacturing process using infrared camera imaging and processing techniques. This project will benefit additive manufacturing by providing real-time inspection of internal geometry that is not currently possible and reduce the time and cost of additive manufactured parts with automated real-time dimensional inspections which deletes post-production inspections.

Phased Array Probe Optimization for the Inspection of Titanium Billets

NASA Astrophysics Data System (ADS)

Rasselkorde, E.; Cooper, I.; Wallace, P.; Lupien, V.

2010-02-01

The manufacturing process of titanium billets can produce multiple sub-surface defects that are particularly difficult to detect during the early stages of production. Failure to detect these defects can lead to subsequent in-service failure. A new and novel automated quality control system is being developed for the inspection of titanium billets destined for use in aerospace applications. The sensors will be deployed by an automated system to minimise the use of manual inspections, which should improve the quality and reliability of these critical inspections early on in the manufacturing process. This paper presents the first part of the work, which is the design and the simulation of the phased array ultrasonic inspection of the billets. A series of phased array transducers were designed to optimise the ultrasonic inspection of a ten inch diameter billet made from Titanium 6Al-4V. A comparison was performed between different probes including a 2D annular sectorial array.

Automatic Quality Inspection of Percussion Cap Mass Production by Means of 3D Machine Vision and Machine Learning Techniques

NASA Astrophysics Data System (ADS)

Tellaeche, A.; Arana, R.; Ibarguren, A.; Martínez-Otzeta, J. M.

The exhaustive quality control is becoming very important in the world's globalized market. One of these examples where quality control becomes critical is the percussion cap mass production. These elements must achieve a minimum tolerance deviation in their fabrication. This paper outlines a machine vision development using a 3D camera for the inspection of the whole production of percussion caps. This system presents multiple problems, such as metallic reflections in the percussion caps, high speed movement of the system and mechanical errors and irregularities in percussion cap placement. Due to these problems, it is impossible to solve the problem by traditional image processing methods, and hence, machine learning algorithms have been tested to provide a feasible classification of the possible errors present in the percussion caps.

40 CFR 60.2141 - By what date must I conduct the initial air pollution control device inspection?

Code of Federal Regulations, 2013 CFR

2013-07-01

... air pollution control device inspection? 60.2141 Section 60.2141 Protection of Environment... Compliance Requirements § 60.2141 By what date must I conduct the initial air pollution control device inspection? (a) The initial air pollution control device inspection must be conducted within 60 days after...

40 CFR 60.2141 - By what date must I conduct the initial air pollution control device inspection?

Code of Federal Regulations, 2014 CFR

2014-07-01

... air pollution control device inspection? 60.2141 Section 60.2141 Protection of Environment... Compliance Requirements § 60.2141 By what date must I conduct the initial air pollution control device inspection? (a) The initial air pollution control device inspection must be conducted within 60 days after...

Quality Management and Control of Low Pressure Cast Aluminum Alloy

NASA Astrophysics Data System (ADS)

Zhang, Dianxi; Zhang, Yanbo; Yang, Xiufan; Chen, Zhaosong; Jiang, Zelan

2018-01-01

This paper briefly reviews the history of low pressure casting and summarizes the major production processes of low pressure casting. It briefly introduces the quality management and control of low pressure cast aluminum alloy. The main processes include are: preparation of raw materials, Melting, refining, physical and chemical analysis, K-mode inspection, sand core, mold, heat treatment and so on.

Electronic Inspection of Beef

NASA Technical Reports Server (NTRS)

Anselmo, Victor J.; Gammell, Paul M.; Clark, Jerry

1987-01-01

Two proposed methods for grading beef quality based on inspection by electronic equipment: one method uses television camera to generate image of a cut of beef as customer sees it; other uses ultrasonics to inspect live animal or unsliced carcasses. Both methods show promise for automated meat inspection.

40 CFR 60.2706 - By what date must I conduct the initial air pollution control device inspection?

Code of Federal Regulations, 2011 CFR

2011-07-01

... air pollution control device inspection? 60.2706 Section 60.2706 Protection of Environment... Requirements § 60.2706 By what date must I conduct the initial air pollution control device inspection? (a) The initial air pollution control device inspection must be conducted within 60 days after installation of the...

150-nm DR contact holes die-to-database inspection

NASA Astrophysics Data System (ADS)

Kuo, Shen C.; Wu, Clare; Eran, Yair; Staud, Wolfgang; Hemar, Shirley; Lindman, Ofer

2000-07-01

Using a failure analysis-driven yield enhancements concept, based on an optimization of the mask manufacturing process and UV reticle inspection is studied and shown to improve the contact layer quality. This is achieved by relating various manufacturing processes to very fine tuned contact defect detection. In this way, selecting an optimized manufacturing process with fine-tuned inspection setup is achieved in a controlled manner. This paper presents a study, performed on a specially designed test reticle, which simulates production contact layers of design rule 250nm, 180nm and 150nm. This paper focuses on the use of advanced UV reticle inspection techniques as part of the process optimization cycle. Current inspection equipment uses traditional and insufficient methods of small contact-hole inspection and review.

49 CFR 195.561 - When must I inspect pipe coating used for external corrosion control?

Code of Federal Regulations, 2010 CFR

2010-10-01

... corrosion control? 195.561 Section 195.561 Transportation Other Regulations Relating to Transportation...) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.561 When must I inspect pipe coating used for external corrosion control? (a) You must inspect all external pipe coating...

49 CFR 195.561 - When must I inspect pipe coating used for external corrosion control?

Code of Federal Regulations, 2011 CFR

2011-10-01

... corrosion control? 195.561 Section 195.561 Transportation Other Regulations Relating to Transportation...) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.561 When must I inspect pipe coating used for external corrosion control? (a) You must inspect all external pipe coating...

49 CFR 195.561 - When must I inspect pipe coating used for external corrosion control?

Code of Federal Regulations, 2013 CFR

2013-10-01

... corrosion control? 195.561 Section 195.561 Transportation Other Regulations Relating to Transportation...) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.561 When must I inspect pipe coating used for external corrosion control? (a) You must inspect all external pipe coating...

49 CFR 195.561 - When must I inspect pipe coating used for external corrosion control?

Code of Federal Regulations, 2014 CFR

2014-10-01

... corrosion control? 195.561 Section 195.561 Transportation Other Regulations Relating to Transportation...) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.561 When must I inspect pipe coating used for external corrosion control? (a) You must inspect all external pipe coating...

49 CFR 195.561 - When must I inspect pipe coating used for external corrosion control?

Code of Federal Regulations, 2012 CFR

2012-10-01

... corrosion control? 195.561 Section 195.561 Transportation Other Regulations Relating to Transportation...) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.561 When must I inspect pipe coating used for external corrosion control? (a) You must inspect all external pipe coating...

10 CFR 71.121 - Internal inspection.

Code of Federal Regulations, 2013 CFR

2013-01-01

... performed for each work operation where necessary to assure quality. If direct inspection of processed... REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality Assurance § 71... execute a program for inspection of activities affecting quality by or for the organization performing the...

10 CFR 71.121 - Internal inspection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... performed for each work operation where necessary to assure quality. If direct inspection of processed... REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality Assurance § 71... execute a program for inspection of activities affecting quality by or for the organization performing the...

10 CFR 71.121 - Internal inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... performed for each work operation where necessary to assure quality. If direct inspection of processed... REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality Assurance § 71... execute a program for inspection of activities affecting quality by or for the organization performing the...

10 CFR 71.121 - Internal inspection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... performed for each work operation where necessary to assure quality. If direct inspection of processed... REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality Assurance § 71... execute a program for inspection of activities affecting quality by or for the organization performing the...

10 CFR 71.121 - Internal inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... performed for each work operation where necessary to assure quality. If direct inspection of processed... REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality Assurance § 71... execute a program for inspection of activities affecting quality by or for the organization performing the...

Continental United States Military Housing Inspections Southeast

DTIC Science & Technology

2015-09-24

and safety, including focus on mold, asbestos , radon, lead-based paint, drinking water quality, and pest management. We conducted this inspection in...electrical system safety inspections. In addition, we inspected to EPA standards governing safe drinking water and toxic substances, radon, asbestos , and...inspections focused on mold, asbestos , radon, lead-based paint, drinking water quality, and pest management. We evaluated the associated plans and

Quality Control by Artificial Vision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lam, Edmond Y.; Gleason, Shaun Scott; Niel, Kurt S.

2010-01-01

Computational technology has fundamentally changed many aspects of our lives. One clear evidence is the development of artificial-vision systems, which have effectively automated many manual tasks ranging from quality inspection to quantitative assessment. In many cases, these machine-vision systems are even preferred over manual ones due to their repeatability and high precision. Such advantages come from significant research efforts in advancing sensor technology, illumination, computational hardware, and image-processing algorithms. Similar to the Special Section on Quality Control by Artificial Vision published two years ago in Volume 17, Issue 3 of the Journal of Electronic Imaging, the present one invited papersmore » relevant to fundamental technology improvements to foster quality control by artificial vision, and fine-tuned the technology for specific applications. We aim to balance both theoretical and applied work pertinent to this special section theme. Consequently, we have seven high-quality papers resulting from the stringent peer-reviewing process in place at the Journal of Electronic Imaging. Some of the papers contain extended treatment of the authors work presented at the SPIE Image Processing: Machine Vision Applications conference and the International Conference on Quality Control by Artificial Vision. On the broad application side, Liu et al. propose an unsupervised texture image segmentation scheme. Using a multilayer data condensation spectral clustering algorithm together with wavelet transform, they demonstrate the effectiveness of their approach on both texture and synthetic aperture radar images. A problem related to image segmentation is image extraction. For this, O'Leary et al. investigate the theory of polynomial moments and show how these moments can be compared to classical filters. They also show how to use the discrete polynomial-basis functions for the extraction of 3-D embossed digits, demonstrating superiority over Fourier

MASQOT: a method for cDNA microarray spot quality control

PubMed Central

Bylesjö, Max; Eriksson, Daniel; Sjödin, Andreas; Sjöström, Michael; Jansson, Stefan; Antti, Henrik; Trygg, Johan

2005-01-01

Background cDNA microarray technology has emerged as a major player in the parallel detection of biomolecules, but still suffers from fundamental technical problems. Identifying and removing unreliable data is crucial to prevent the risk of receiving illusive analysis results. Visual assessment of spot quality is still a common procedure, despite the time-consuming work of manually inspecting spots in the range of hundreds of thousands or more. Results A novel methodology for cDNA microarray spot quality control is outlined. Multivariate discriminant analysis was used to assess spot quality based on existing and novel descriptors. The presented methodology displays high reproducibility and was found superior in identifying unreliable data compared to other evaluated methodologies. Conclusion The proposed methodology for cDNA microarray spot quality control generates non-discrete values of spot quality which can be utilized as weights in subsequent analysis procedures as well as to discard spots of undesired quality using the suggested threshold values. The MASQOT approach provides a consistent assessment of spot quality and can be considered an alternative to the labor-intensive manual quality assessment process. PMID:16223442

[Recommendations for inspections of the French nuclear safety authority].

PubMed

Rousse, C; Chauvet, B

2015-10-01

The French nuclear safety authority is responsible for the control of radiation protection in radiotherapy since 2002. Controls are based on the public health and the labour codes and on the procedures defined by the controlled health care facility for its quality and safety management system according to ASN decision No. 2008-DC-0103. Inspectors verify the adequacy of the quality and safety management procedures and their implementation, and select process steps on the basis of feedback from events notified to ASN. Topics of the inspection are communicated to the facility at the launch of a campaign, which enables them to anticipate the inspectors' expectations. In cases where they are not physicians, inspectors are not allowed to access information covered by medical confidentiality. The consulted documents must therefore be expunged of any patient-identifying information. Exchanges before the inspection are intended to facilitate the provision of documents that may be consulted. Finally, exchange slots between inspectors and the local professionals must be organized. Based on improvements achieved by the health care centres and on recommendations from a joint working group of radiotherapy professionals and the nuclear safety authority, changes will be made in the control procedure that will be implemented when developing the inspection program for 2016-2019. Copyright © 2015. Published by Elsevier SAS.

Error Sources in Proccessing LIDAR Based Bridge Inspection

NASA Astrophysics Data System (ADS)

Bian, H.; Chen, S. E.; Liu, W.

2017-09-01

Bridge inspection is a critical task in infrastructure management and is facing unprecedented challenges after a series of bridge failures. The prevailing visual inspection was insufficient in providing reliable and quantitative bridge information although a systematic quality management framework was built to ensure visual bridge inspection data quality to minimize errors during the inspection process. The LiDAR based remote sensing is recommended as an effective tool in overcoming some of the disadvantages of visual inspection. In order to evaluate the potential of applying this technology in bridge inspection, some of the error sources in LiDAR based bridge inspection are analysed. The scanning angle variance in field data collection and the different algorithm design in scanning data processing are the found factors that will introduce errors into inspection results. Besides studying the errors sources, advanced considerations should be placed on improving the inspection data quality, and statistical analysis might be employed to evaluate inspection operation process that contains a series of uncertain factors in the future. Overall, the development of a reliable bridge inspection system requires not only the improvement of data processing algorithms, but also systematic considerations to mitigate possible errors in the entire inspection workflow. If LiDAR or some other technology can be accepted as a supplement for visual inspection, the current quality management framework will be modified or redesigned, and this would be as urgent as the refine of inspection techniques.

Software Formal Inspections Standard

NASA Technical Reports Server (NTRS)

1993-01-01

This Software Formal Inspections Standard (hereinafter referred to as Standard) is applicable to NASA software. This Standard defines the requirements that shall be fulfilled by the software formal inspections process whenever this process is specified for NASA software. The objective of this Standard is to define the requirements for a process that inspects software products to detect and eliminate defects as early as possible in the software life cycle. The process also provides for the collection and analysis of inspection data to improve the inspection process as well as the quality of the software.

Optimizing defect inspection strategy through the use of design-aware database control layers

NASA Astrophysics Data System (ADS)

Stoler, Dvori; Ruch, Wayne; Ma, Weimin; Chakravarty, Swapnajit; Liu, Steven; Morgan, Ray; Valadez, John; Moore, Bill; Burns, John

2007-10-01

Resolution limitations in the mask making process can cause differences between the features that appear in a database and those printed to a reticle. These differences may result from intentional or unintentional features in the database exceeding the resolution limit of the mask making process such as small gaps or lines in the data, line end shortening on small sub-resolution assist features etc creating challenges to both mask writing and mask inspection. Areas with high variance from design to mask, often referred to as high MEEF areas (mask error enhancement factor), become highly problematic and can directly impact mask and device yield, mask manufacturing cycle time and ultimately mask costs. Specific to mask inspection it may be desirable to inspect certain non-critical or non-relevant features at reduced sensitivity so as not to detect real, but less significant process defects. In contrast there may also be times where increased sensitivity is required for critical mask features or areas. Until recently, this process was extremely manual, creating added time and cost to the mask inspection cycle. Shifting to more intelligent and automated inspection flows is the key focus of this paper. A novel approach to importing design data directly into the mask inspection to include both MDP generated MRC errors files and LRC generated MEEF files. The results of recently developed inspection and review capability based upon controlling defect inspection using design aware data base control layers on a pixel basis are discussed. Typical mask shop applications and implementations will be shown.

Process Approach to Determining Quality Inspection Deployment

DTIC Science & Technology

2015-06-08

27 B.1 The Deming Rule...inspection is effective. The Deming rule is explained in more detail in Appendix B. Basically the probability of error is compared to the cost of...cost or risk to repair defects escaped from inspection justify reducing inspectors. (See Appendix B for Deming rule discussion.) Three quantities must

Neural network Hilbert transform based filtered backprojection for fast inline x-ray inspection

NASA Astrophysics Data System (ADS)

Janssens, Eline; De Beenhouwer, Jan; Van Dael, Mattias; De Schryver, Thomas; Van Hoorebeke, Luc; Verboven, Pieter; Nicolai, Bart; Sijbers, Jan

2018-03-01

X-ray imaging is an important tool for quality control since it allows to inspect the interior of products in a non-destructive way. Conventional x-ray imaging, however, is slow and expensive. Inline x-ray inspection, on the other hand, can pave the way towards fast and individual quality control, provided that a sufficiently high throughput can be achieved at a minimal cost. To meet these criteria, an inline inspection acquisition geometry is proposed where the object moves and rotates on a conveyor belt while it passes a fixed source and detector. Moreover, for this acquisition geometry, a new neural-network-based reconstruction algorithm is introduced: the neural network Hilbert transform based filtered backprojection. The proposed algorithm is evaluated both on simulated and real inline x-ray data and has shown to generate high quality reconstructions of 400  ×  400 reconstruction pixels within 200 ms, thereby meeting the high throughput criteria.

Industrial Inspection with Open Eyes: Advance with Machine Vision Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Zheng; Ukida, H.; Niel, Kurt

Machine vision systems have evolved significantly with the technology advances to tackle the challenges from modern manufacturing industry. A wide range of industrial inspection applications for quality control are benefiting from visual information captured by different types of cameras variously configured in a machine vision system. This chapter screens the state of the art in machine vision technologies in the light of hardware, software tools, and major algorithm advances for industrial inspection. The inspection beyond visual spectrum offers a significant complementary to the visual inspection. The combination with multiple technologies makes it possible for the inspection to achieve a bettermore » performance and efficiency in varied applications. The diversity of the applications demonstrates the great potential of machine vision systems for industry.« less

MRT fuel element inspection at Dounreay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gibson, J.

1997-08-01

To ensure that their production and inspection processes are performed in an acceptable manner, ie. auditable and traceable, the MTR Fuel Element Fabrication Plant at Dounreay operates to a documented quality system. This quality system, together with the fuel element manufacturing and inspection operations, has been independently certified to ISO9002-1987, EN29002-1987 and BS5750:Pt2:1987 by Lloyd`s Register Quality Assurance Limited (LRQA). This certification also provides dual accreditation to the relevant German, Dutch and Australian certification bodies. This paper briefly describes the quality system, together with the various inspection stages involved in the manufacture of MTR fuel elements at Dounreay.

[Quality control an assessment system. Its location within a program for food, nutrition and metabolic intervention].

PubMed

Santana Porbén, S

2012-01-01

A design proposal for a HQCAS Hospital Quality Control and Assessment System of the nutritional and feeding care processes conducted in a hospital environment is presented in this article. The design proposal is accompanied of the results of inspections conducted by the hospital NST Nutritional Support Group between 2005-2010. The system design includes quality policies that should rule the useful and safe conduction of such processes, the recording and documentary foundations of the System, and the quality control and assessment exercises for the continuous verification of such established policies. The current state of the conduction of these processes was documented from secondary records opened by the NST after satisfying consultation requests from the medical care teams of the institution. Inspections conducted by the NST revealed that less than half of clinical charts contained information minimally enough for elaborating nutritional judgments, almost one-fifth of the assisted patients were on Nils Per Oris, for whom no nutritional support schemes were prescribed, and a low prescription and usage of artificial nutrition schemes. Corrective measures adopted by the NST served to significantly increase the rates of successful completion of inspected processes. Quality assurance of feeding and nutritional care processes is a practical as well as an intellectual activity subjected to constant remodeling, in order to always warrant the fulfillment of quality policies advanced by the NST, and thus, that the patient benefits from the prescribed nutritional intervention strategy.

47 CFR 17.47 - Inspection of antenna structure lights and associated control equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 1 2013-10-01 2013-10-01 false Inspection of antenna structure lights and... CONSTRUCTION, MARKING, AND LIGHTING OF ANTENNA STRUCTURES Specifications for Obstruction Marking and Lighting of Antenna Structures § 17.47 Inspection of antenna structure lights and associated control equipment...

47 CFR 17.47 - Inspection of antenna structure lights and associated control equipment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 1 2012-10-01 2012-10-01 false Inspection of antenna structure lights and... CONSTRUCTION, MARKING, AND LIGHTING OF ANTENNA STRUCTURES Specifications for Obstruction Marking and Lighting of Antenna Structures § 17.47 Inspection of antenna structure lights and associated control equipment...

47 CFR 17.47 - Inspection of antenna structure lights and associated control equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Inspection of antenna structure lights and... CONSTRUCTION, MARKING, AND LIGHTING OF ANTENNA STRUCTURES Specifications for Obstruction Marking and Lighting of Antenna Structures § 17.47 Inspection of antenna structure lights and associated control equipment...

47 CFR 17.47 - Inspection of antenna structure lights and associated control equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false Inspection of antenna structure lights and... CONSTRUCTION, MARKING, AND LIGHTING OF ANTENNA STRUCTURES Specifications for Obstruction Marking and Lighting of Antenna Structures § 17.47 Inspection of antenna structure lights and associated control equipment...

47 CFR 17.47 - Inspection of antenna structure lights and associated control equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 1 2014-10-01 2014-10-01 false Inspection of antenna structure lights and... CONSTRUCTION, MARKING, AND LIGHTING OF ANTENNA STRUCTURES Specifications for Obstruction Marking and Lighting of Antenna Structures § 17.47 Inspection of antenna structure lights and associated control equipment...

Relative attitude dynamics and control for a satellite inspection mission

NASA Astrophysics Data System (ADS)

Horri, Nadjim M.; Kristiansen, Kristian U.; Palmer, Phil; Roberts, Mark

2012-02-01

The problem of conducting an inspection mission from a chaser satellite orbiting a target spaceraft is considered. It is assumed that both satellites follow nearly circular orbits. The relative orbital motion is described by the Hill-Clohessy-Wiltshire equation. In the case of an elliptic relative orbit, it is shown that an inspection mission is feasible when the chaser is inertially pointing, provided that the camera mounted on the chaser satellite has sufficiently large field of view. The same possibility is shown when the optical axis of the chaser's camera points in, or opposite to, the tangential direction of the local vertical local horizontal frame. For an arbitrary relative orbit and arbitrary initial conditions, the concept of relative Euler angles is defined for this inspection mission. The expression of the desired relative angular velocity vector is derived as a function of Cartesian coordinates of the relative orbit. A quaternion feedback controller is then designed and shown to perform relative attitude control with admissible internal torques. Three different types of relative orbits are considered, namely the elliptic, Pogo and drifting relative orbits. Measurements of the relative orbital motion are assumed to be available from optical navigation.

Nuclear Technology. Course 28: Welding Inspection. Module 28-5, Qualifications.

ERIC Educational Resources Information Center

Espy, John

This fifth in a series of ten modules for a course titled Welding Inspection describes qualification requirements for welding procedures and welders and the role of the nuclear quality assurance/quality control technician. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3)…

Pathology Residents Comprise Inspection Team for a CAP Self-Inspection.

PubMed

Beal, Stacy G; Kresak, Jesse L; Yachnis, Anthony T

2017-01-01

We report our experience at the University of Florida in which residents and fellows served as the inspection team for a College of American Pathologists (CAP) self-inspection. We aimed to determine whether the CAP self-inspection could serve as a learning opportunity for pathology residents and fellows. To prepare for the inspection, we provided a series of 4 lunchtime seminars covering numerous laboratory management topics relating to inspections and laboratory quality. Preparation for the inspection began approximately 4 months prior to the date of the inspection. The intent was to simulate a CAP peer inspection, with the exception that the date was announced. The associate residency program director served as the team leader. All residents and fellows completed inspector training provided by CAP, and the team leader completed the team leader training. A 20 question pre- and posttest was administered; additionally, an anonymous survey was given after the inspection. The residents' and fellows' posttest scores were an average of 15% higher than on the pretest ( P < .01). The surveys as well as subjective comments were overwhelmingly positive. In conclusion, the resident's and fellow's experience as an inspector during a CAP self-inspection was a useful tool to learn accreditation and laboratory management.

Pathology Residents Comprise Inspection Team for a CAP Self-Inspection

PubMed Central

Kresak, Jesse L.; Yachnis, Anthony T.

2017-01-01

We report our experience at the University of Florida in which residents and fellows served as the inspection team for a College of American Pathologists (CAP) self-inspection. We aimed to determine whether the CAP self-inspection could serve as a learning opportunity for pathology residents and fellows. To prepare for the inspection, we provided a series of 4 lunchtime seminars covering numerous laboratory management topics relating to inspections and laboratory quality. Preparation for the inspection began approximately 4 months prior to the date of the inspection. The intent was to simulate a CAP peer inspection, with the exception that the date was announced. The associate residency program director served as the team leader. All residents and fellows completed inspector training provided by CAP, and the team leader completed the team leader training. A 20 question pre- and posttest was administered; additionally, an anonymous survey was given after the inspection. The residents’ and fellows’ posttest scores were an average of 15% higher than on the pretest (P < .01). The surveys as well as subjective comments were overwhelmingly positive. In conclusion, the resident’s and fellow’s experience as an inspector during a CAP self-inspection was a useful tool to learn accreditation and laboratory management. PMID:28725788

Robotic control and inspection verification

NASA Technical Reports Server (NTRS)

Davis, Virgil Leon

1991-01-01

Three areas of possible commercialization involving robots at the Kennedy Space Center (KSC) are discussed: a six degree-of-freedom target tracking system for remote umbilical operations; an intelligent torque sensing end effector for operating hand valves in hazardous locations; and an automatic radiator inspection device, a 13 by 65 foot robotic mechanism involving completely redundant motors, drives, and controls. Aspects concerning the first two innovations can be integrated to enable robots or teleoperators to perform tasks involving orientation and panal actuation operations that can be done with existing technology rather than waiting for telerobots to incorporate artificial intelligence (AI) to perform 'smart' autonomous operations. The third robot involves the application of complete control hardware redundancy to enable performance of work over and near expensive Space Shuttle hardware. The consumer marketplace may wish to explore commercialization of similiar component redundancy techniques for applications when a robot would not normally be used because of reliability concerns.

Visual and x-ray inspection characteristics of eutectic and lead free assemblies

NASA Technical Reports Server (NTRS)

Ghaffarian, R.

2003-01-01

For high reliability applications, visual inspection has been the key technique for most conventional electronic package assemblies. Now, the use of x-ray technique has become an additional inspection requirement for quality control and detection of unique defects due to manufacturing of advanced electronic array packages such as ball grid array (BGAs) and chip scale packages (CSPs).

[Quality process control system of Chinese medicine preparation based on "holistic view"].

PubMed

Wang, Ya-Qi; Jiao, Jiao-Jiao; Wu, Zhen-Feng; Zheng, Qin; Yang, Ming

2018-01-01

"High quality, safety and effectiveness" are the primary principles for the pharmaceutical research and development process in China. The quality of products relies not only on the inspection method, but also on the design and development, process control and standardized management. The quality depends on the process control level. In this paper, the history and current development of quality control of traditional Chinese medicine (TCM) preparations are reviewed systematically. Based on the development model of international drug quality control and the misunderstanding of quality control of TCM preparations, the reasons for impacting the homogeneity of TCM preparations are analyzed and summarized. According to TCM characteristics, efforts were made to control the diversity of TCM, make "unstable" TCM into "stable" Chinese patent medicines, put forward the concepts of "holistic view" and "QbD (quality by design)", so as to create the "holistic, modular, data, standardized" model as the core of TCM preparation quality process control model. Scientific studies shall conform to the actual production of TCM preparations, and be conducive to supporting advanced equipment and technology upgrade, thoroughly applying the scientific research achievements in Chinese patent medicines, and promoting the cluster application and transformation application of TCM pharmaceutical technology, so as to improve the quality and effectiveness of the TCM industry and realize the green development. Copyright© by the Chinese Pharmaceutical Association.

Dimensional Metrology of Non-rigid Parts Without Specialized Inspection Fixtures =

NASA Astrophysics Data System (ADS)

Sabri, Vahid

Quality control is an important factor for manufacturing companies looking to prosper in an era of globalization, market pressures and technological advances. Functionality and product quality cannot be guaranteed without this important aspect. Manufactured parts have deviations from their nominal (CAD) shape caused by the manufacturing process. Thus, geometric inspection is a very important element in the quality control of mechanical parts. We will focus here on the geometric inspection of non-rigid (flexible) parts which are widely used in the aeronautic and automotive industries. Non-rigid parts can have different forms in a free-state condition compared with their nominal models due to residual stress and gravity loads. To solve this problem, dedicated inspection fixtures are generally used in industry to compensate for the displacement of such parts for simulating the use state in order to perform geometric inspections. These fixtures and the installation and inspection processes are expensive and time-consuming. Our aim in this thesis is therefore to develop an inspection method which eliminates the need for specialized fixtures. This is done by acquiring a point cloud from the part in a free-state condition using a contactless measuring device such as optical scanning and comparing it with the CAD model for the deviation identification. Using a non-rigid registration method and finite element analysis, we numerically inspect the profile of a non-rigid part. To do so, a simulated displacement is performed using an improved definition of displacement boundary conditions for simulating unfixed parts. In addition, we propose a numerical method for dimensional metrology of non-rigid parts in a free-state condition based on the arc length measurement by calculating the geodesic distance using the Fast Marching Method (FMM). In this thesis, we apply our developed methods on industrial non-rigid parts with free-form surfaces simulated with different types of

Quality Assurance of Chemical Measurements.

ERIC Educational Resources Information Center

Taylor, John K.

1981-01-01

Reviews aspects of quality control (methods to control errors) and quality assessment (verification that systems are operating within acceptable limits) including an analytical measurement system, quality control by inspection, control charts, systematic errors, and use of SRMs, materials for which properties are certified by the National Bureau…

40 CFR 62.14441 - When must I inspect my HMIWI equipment and air pollution control devices?

Code of Federal Regulations, 2014 CFR

2014-07-01

... and air pollution control devices? 62.14441 Section 62.14441 Protection of Environment ENVIRONMENTAL... my HMIWI equipment and air pollution control devices? (a) You must inspect your large, medium, small... inspect the air pollution control devices on your large, medium, small or small rural HMIWI by May 13...

40 CFR 62.14441 - When must I inspect my HMIWI equipment and air pollution control devices?

Code of Federal Regulations, 2013 CFR

2013-07-01

... and air pollution control devices? 62.14441 Section 62.14441 Protection of Environment ENVIRONMENTAL... my HMIWI equipment and air pollution control devices? (a) You must inspect your large, medium, small... inspect the air pollution control devices on your large, medium, small or small rural HMIWI by May 13...

Application of polarization in high speed, high contrast inspection

NASA Astrophysics Data System (ADS)

Novak, Matthew J.

2017-08-01

Industrial optical inspection often requires high speed and high throughput of materials. Engineers use a variety of techniques to handle these inspection needs. Some examples include line scan cameras, high speed multi-spectral and laser-based systems. High-volume manufacturing presents different challenges for inspection engineers. For example, manufacturers produce some components in quantities of millions per month, per week or even per day. Quality control of so many parts requires creativity to achieve the measurement needs. At times, traditional vision systems lack the contrast to provide the data required. In this paper, we show how dynamic polarization imaging captures high contrast images. These images are useful for engineers to perform inspection tasks in some cases where optical contrast is low. We will cover basic theory of polarization. We show how to exploit polarization as a contrast enhancement technique. We also show results of modeling for a polarization inspection application. Specifically, we explore polarization techniques for inspection of adhesives on glass.

The quality of health care in prison: results of a year's programme of semistructured inspections.

PubMed Central

Reed, J.; Lyne, M.

1997-01-01

OBJECTIVES: To assess, as part of wider inspections by HM Inspectorate of Prisons, the extent and quality of health care in prisons in England and Wales. DESIGN: Inspections based on a set of "expectations" derived mainly from existing healthcare quality standards published by the prison service and existing ethical guidelines; questionnaire survey of prisoners. SUBJECTS: 19 prisons in England and Wales, 1996-7. MAIN OUTCOME MEASURES: Appraisals of needs assessment and the commissioning and delivery of health care against the inspectorate's expectations. RESULTS: The quality of health care varied greatly. A few prisons provided health care broadly equivalent to NHS care, but in many the health care was of low quality, some doctors were not adequately trained to do the work they faced, and some care failed to meet proper ethical standards. Little professional support was available to healthcare staff. CONCLUSIONS: The current policy for improving health care in prisons is not likely to achieve its objectives and is potentially wasteful. The prison service needs to recognise that expertise in the commissioning and delivery of health care is overwhelming based in the NHS. The current review of the provision of health care in prisons offers an opportunity to ensure that prisoners are not excluded from high quality health care. PMID:9418090

Distributed control system in a car-body inspection station

NASA Astrophysics Data System (ADS)

Yang, Xueyou; Ren, Dahai; Ye, Shenghua; Lu, Hongbo; Duan, Jilin

1997-06-01

In this paper, a distributed control network in autocar-body visual inspection station is presented in which PC is used as the host processor and single-chip microcomputers are employed as slave controllers. The physical interface of the control network and the relevant hardware are introduced in this paper. Meanwhile, a minute research on data communication is performed, relevant protocols on data framing, instruction codes and channel access methods have been laid down and part of related software is presented.

40 CFR 60.5215 - By what date must I conduct annual air pollution control device inspections and make any...

Code of Federal Regulations, 2011 CFR

2011-07-01

... pollution control device inspections and make any necessary repairs? 60.5215 Section 60.5215 Protection of... air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution control device used to comply with the emission limits, according...

In-Process Atomic-Force Microscopy (AFM) Based Inspection

PubMed Central

Mekid, Samir

2017-01-01

A new in-process atomic-force microscopy (AFM) based inspection is presented for nanolithography to compensate for any deviation such as instantaneous degradation of the lithography probe tip. Traditional method used the AFM probes for lithography work and retract to inspect the obtained feature but this practice degrades the probe tip shape and hence, affects the measurement quality. This paper suggests a second dedicated lithography probe that is positioned back-to-back to the AFM probe under two synchronized controllers to correct any deviation in the process compared to specifications. This method shows that the quality improvement of the nanomachining, in progress probe tip wear, and better understanding of nanomachining. The system is hosted in a recently developed nanomanipulator for educational and research purposes. PMID:28561747

Operational quality control of daily precipitation using spatio-climatological consistency testing

NASA Astrophysics Data System (ADS)

Scherrer, S. C.; Croci-Maspoli, M.; van Geijtenbeek, D.; Naguel, C.; Appenzeller, C.

2010-09-01

Quality control (QC) of meteorological data is of utmost importance for climate related decisions. The search for an effective automated QC of precipitation data has proven difficult and many weather services still use mainly manual inspection of daily precipitation including MeteoSwiss. However, man power limitations force many weather services to move towards less labour intensive and more automated QC with the challenge to keeping data quality high. In the last decade, several approaches have been presented to objectify daily precipitation QC. Here we present a spatio-climatological approach that will be implemented operationally at MeteoSwiss. It combines the information from the event based spatial distribution of everyday's precipitation field and the historical information of the interpolation error using different precipitation intensity intervals. Expert judgement shows that the system is able to detect potential outliers very well (hardly any missed errors) without creating too many false alarms that need human inspection. 50-80% of all flagged values have been classified as real errors by the data editor. This is much better than the roughly 15-20% using standard spatial regression tests. Very helpful in the QC process is the automatic redistribution of accumulated several day sums. Manual inspection in operations can be reduced and the QC of precipitation objectified substantially.

40 CFR 60.2716 - By what date must I conduct the annual air pollution control device inspection?

Code of Federal Regulations, 2014 CFR

2014-07-01

... air pollution control device inspection? 60.2716 Section 60.2716 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY... annual air pollution control device inspection), you must complete the air pollution control device...

40 CFR 60.2716 - By what date must I conduct the annual air pollution control device inspection?

Code of Federal Regulations, 2012 CFR

2012-07-01

... air pollution control device inspection? 60.2716 Section 60.2716 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY... annual air pollution control device inspection), you must complete the air pollution control device...

40 CFR 60.2716 - By what date must I conduct the annual air pollution control device inspection?

Code of Federal Regulations, 2013 CFR

2013-07-01

... air pollution control device inspection? 60.2716 Section 60.2716 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY... annual air pollution control device inspection), you must complete the air pollution control device...

Line-scan spatially offset Raman spectroscopy for inspecting subsurface food safety and quality

NASA Astrophysics Data System (ADS)

Qin, Jianwei; Chao, Kuanglin; Kim, Moon S.

2016-05-01

This paper presented a method for subsurface food inspection using a newly developed line-scan spatially offset Raman spectroscopy (SORS) technique. A 785 nm laser was used as a Raman excitation source. The line-shape SORS data was collected in a wavenumber range of 0-2815 cm-1 using a detection module consisting of an imaging spectrograph and a CCD camera. A layered sample, which was created by placing a plastic sheet cut from the original container on top of cane sugar, was used to test the capability for subsurface food inspection. A whole set of SORS data was acquired in an offset range of 0-36 mm (two sides of the laser) with a spatial interval of 0.07 mm. Raman spectrum from the cane sugar under the plastic sheet was resolved using self-modeling mixture analysis algorithms, demonstrating the potential of the technique for authenticating foods and ingredients through packaging. The line-scan SORS measurement technique provides a new method for subsurface inspection of food safety and quality.

7 CFR 75.31 - Appeal inspection certificate.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND CERTIFICATION OF QUALITY OF AGRICULTURAL AND VEGETABLE SEEDS Appeal Inspection § 75.31 Appeal... inspection certificate previously issued for the seed involved. Each appeal inspection certificate shall clearly identify the number and date of the inspection certificate which it supersedes. The superseded...

Integration of Machining and Inspection in Aerospace Manufacturing

NASA Astrophysics Data System (ADS)

Simpson, Bart; Dicken, Peter J.

2011-12-01

The main challenge for aerospace manufacturers today is to develop the ability to produce high-quality products on a consistent basis as quickly as possible and at the lowest-possible cost. At the same time, rising material prices are making the cost of scrap higher than ever so making it more important to minimise waste. Proper inspection and quality control methods are no longer a luxury; they are an essential part of every manufacturing operation that wants to grow and be successful. However, simply bolting on some quality control procedures to the existing manufacturing processes is not enough. Inspection must be fully-integrated with manufacturing for the investment to really produce significant improvements. The traditional relationship between manufacturing and inspection is that machining is completed first on the company's machine tools and the components are then transferred to dedicated inspection equipment to be approved or rejected. However, as machining techniques become more sophisticated, and as components become larger and more complex, there are a growing number of cases where closer integration is required to give the highest productivity and the biggest reductions in wastage. Instead of a simple linear progression from CAD to CAM to machining to inspection, a more complicated series of steps is needed, with extra data needed to fill any gaps in the information available at the various stages. These new processes can be grouped under the heading of "adaptive machining". The programming of most machining operations is based around knowing three things: the position of the workpiece on the machine, the starting shape of the material to be machined, and the final shape that needs to be achieved at the end of the operation. Adaptive machining techniques allow successful machining when at least one of those elements is unknown, by using in-process measurement to close the information gaps in the process chain. It also allows any errors to be spotted

Control of a Serpentine Robot for Inspection Tasks

NASA Technical Reports Server (NTRS)

Colbaugh, R.; Glass, K.; Seraji, H.

1994-01-01

This paper presents a simple and robust kinematic control scheme for the JPL serpentine robot system. The proposed strategy is developed using the dampened-least-squares/configuration control methodology, and permits the considerable dexterity of the JPL serpentine robot to be effectively utilized for maneuvering in the congested and uncertain workspaces often encountered in inspection tasks. Computer simulation results are given for the 20 degree-of-freedom (DOF) manipulator system obtained by mounting the twelve DOF serpentine robot at the end-effector of an eight DOF Robotics Research arm/lathe-bed system. These simulations demonstrate that the proposed approach provides an effective method of controlling this complex system.

Field Operations and Enforcement Manual for Air Pollution Control. Volume II: Control Technology and General Source Inspection.

ERIC Educational Resources Information Center

Weisburd, Melvin I.

The Field Operations and Enforcement Manual for Air Pollution Control, Volume II, explains in detail the following: technology of source control, modification of operations, particulate control equipment, sulfur dioxide removal systems for power plants, and control equipment for gases and vapors; inspection procedures for general sources, fuel…

Software Formal Inspections Guidebook

NASA Technical Reports Server (NTRS)

1993-01-01

The Software Formal Inspections Guidebook is designed to support the inspection process of software developed by and for NASA. This document provides information on how to implement a recommended and proven method for conducting formal inspections of NASA software. This Guidebook is a companion document to NASA Standard 2202-93, Software Formal Inspections Standard, approved April 1993, which provides the rules, procedures, and specific requirements for conducting software formal inspections. Application of the Formal Inspections Standard is optional to NASA program or project management. In cases where program or project management decide to use the formal inspections method, this Guidebook provides additional information on how to establish and implement the process. The goal of the formal inspections process as documented in the above-mentioned Standard and this Guidebook is to provide a framework and model for an inspection process that will enable the detection and elimination of defects as early as possible in the software life cycle. An ancillary aspect of the formal inspection process incorporates the collection and analysis of inspection data to effect continual improvement in the inspection process and the quality of the software subjected to the process.

On-rail solution for autonomous inspections in electrical substations

NASA Astrophysics Data System (ADS)

Silva, Bruno P. A.; Ferreira, Rafael A. M.; Gomes, Selson C.; Calado, Flavio A. R.; Andrade, Roberto M.; Porto, Matheus P.

2018-05-01

This work presents an alternative solution for autonomous inspections in electrical substations. The autonomous system is a robot that moves on rails, collects infrared and visible images of selected targets, also processes the data and predicts the components lifetime. The robot moves on rails to overcome difficulties found in not paved substations commonly encountered in Brazil. We take advantage of using rails to convey the data by them, minimizing the electromagnetic interference, and at the same time transmitting electrical energy to feed the autonomous system. As part of the quality control process, we compared thermographic inspections made by the robot with inspections made by a trained thermographer using a scientific camera Flir® SC660. The results have shown that the robot achieved satisfactory results, identifying components and measuring temperature accurately. The embodied routine considers the weather changes along the day, providing a standard result of the components thermal response, also gives the uncertainty of temperature measurement, contributing to the quality in the decision making process.

40 CFR 60.2716 - By what date must I conduct the annual air pollution control device inspection?

Code of Federal Regulations, 2011 CFR

2011-07-01

... air pollution control device inspection? 60.2716 Section 60.2716 Protection of Environment... Requirements § 60.2716 By what date must I conduct the annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution control device...

40 CFR 60.2151 - By what date must I conduct the annual air pollution control device inspection?

Code of Federal Regulations, 2013 CFR

2013-07-01

... air pollution control device inspection? 60.2151 Section 60.2151 Protection of Environment... Compliance Requirements § 60.2151 By what date must I conduct the annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution control...

40 CFR 60.2151 - By what date must I conduct the annual air pollution control device inspection?

Code of Federal Regulations, 2014 CFR

2014-07-01

... air pollution control device inspection? 60.2151 Section 60.2151 Protection of Environment... Compliance Requirements § 60.2151 By what date must I conduct the annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution control...

Metropolitan Boston air quality control region: transportation control plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1975-02-28

The EPA is considering a number of amendments to the transportation control plan which it promulgated Nov. 8, 1973 for the Metropolitan Boston Intrastate Air Quality Control Region. Included in the proposed amendments is a revised regulation for reduction of commuter travel which would include students and employees. This program would be implemented in conjunction with the carpool matching program being developed by the Commonwealth of Massachusetts and the employee pass program offered by the Massachusetts Bay Transportation Authority. A new provision for limiting overall hydrocarbon emissions from major users of organic compounds is included. Also published are a proposalmore » for encouraging bicycle use, new proposals for controlling carbon monoxide levels outside the Boston core area, and a new procedure for periodic monitoring and updating of the plan. Other features of the original plan are retained with modifications in areas including the ceiling on the level of commercial parking spaces in the so-called ''freeze'' area, limitations of on-street commuter parking, a semiannual inspection and maintenance program, a retrofit program, and incentives for carpool and transit use.« less

Inspection planning development: An evolutionary approach using reliability engineering as a tool

NASA Technical Reports Server (NTRS)

Graf, David A.; Huang, Zhaofeng

1994-01-01

This paper proposes an evolutionary approach for inspection planning which introduces various reliability engineering tools into the process and assess system trade-offs among reliability, engineering requirement, manufacturing capability and inspection cost to establish an optimal inspection plan. The examples presented in the paper illustrate some advantages and benefits of the new approach. Through the analysis, reliability and engineering impacts due to manufacturing process capability and inspection uncertainty are clearly understood; the most cost effective and efficient inspection plan can be established and associated risks are well controlled; some inspection reductions and relaxations are well justified; and design feedbacks and changes may be initiated from the analysis conclusion to further enhance reliability and reduce cost. The approach is particularly promising as global competitions and customer quality improvement expectations are rapidly increasing.

Device Rotates Bearing Balls For Inspection

NASA Technical Reports Server (NTRS)

Burley, R. K.

1988-01-01

Entire surface of ball inspected automatically and quickly. Device holds and rotates bearing ball for inspection by optical or mechanical surface-quality probe, eddy-current probe for detection of surface or subsurface defects, or circumference-measuring tool. Ensures entire surface of ball moves past inspection head quickly. New device saves time and increases reliability of inspections of spherical surfaces. Simple to operate and provides quick and easy access for loading and unloading of balls during inspection.

9 CFR 331.4 - Control and disposal of non-federally-inspected products in States designated under paragraph 301...

Code of Federal Regulations, 2011 CFR

2011-01-01

... TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION SPECIAL... HEALTH AND FOR SUCH DESIGNATED ESTABLISHMENTS § 331.4 Control and disposal of non-federally-inspected...

CD control with defect inspection: you can teach an old dog a new trick

NASA Astrophysics Data System (ADS)

Utzny, Clemens; Ullrich, Albrecht; Heumann, Jan; Mohn, Elias; Meusemann, Stefan; Seltmann, Rolf

2012-11-01

Achieving the required critical dimensions (CD) with the best possible uniformity (CDU) on photo-masks has always played a pivotal role in enabling chip technology. Current control strategies are based on scanning electron microscopy (SEM) based measurements implying a sparse spatial resolution on the order of ~ 10-2 m to 10-1 m. A higher spatial resolution could be reached with an adequate measurement sampling, however the increase in the number of measurements makes this approach in the context of a productive environment unfeasible. With the advent of more powerful defect inspection tools a significantly higher spatial resolution of 10-4 m can be achieved by measuring also CD during the regular defect inspection. This method is not limited to the measurement of specific measurement features thus paving the way to a CD assessment of all electrically relevant mask patterns. Enabling such a CD measurement gives way to new realms of CD control. Deterministic short range CD effects which were previously interpreted as noise can be resolved and addressed by CD compensation methods. This in can lead to substantial improvements of the CD uniformity. Thus the defect inspection mediated CD control closes a substantial gap in the mask manufacturing process by allowing the control of short range CD effects which were up till now beyond the reach of regular CD SEM based control strategies. This increase in spatial resolution also counters the decrease in measurement precision due to the usage of an optical system. In this paper we present detailed results on a) the CD data generated during the inspection process, b) the analytical tools needed for relating this data to CD SEM measurement and c) how the CD inspection process enables new dimension of CD compensation within the mask manufacturing process. We find that the inspection based CD measurement generates typically around 500000 measurements with a homogeneous covering of the active mask area. In comparing the CD

Automated visual inspection for polished stone manufacture

NASA Astrophysics Data System (ADS)

Smith, Melvyn L.; Smith, Lyndon N.

2003-05-01

Increased globalisation of the ornamental stone market has lead to increased competition and more rigorous product quality requirements. As such, there are strong motivators to introduce new, more effective, inspection technologies that will help enable stone processors to reduce costs, improve quality and improve productivity. Natural stone surfaces may contain a mixture of complex two-dimensional (2D) patterns and three-dimensional (3D) features. The challenge in terms of automated inspection is to develop systems able to reliably identify 3D topographic defects, either naturally occurring or resulting from polishing, in the presence of concomitant complex 2D stochastic colour patterns. The resulting real-time analysis of the defects may be used in adaptive process control, in order to avoid the wasteful production of defective product. An innovative approach, using structured light and based upon an adaptation of the photometric stereo method, has been pioneered and developed at UWE to isolate and characterize mixed 2D and 3D surface features. The method is able to undertake tasks considered beyond the capabilities of existing surface inspection techniques. The approach has been successfully applied to real stone samples, and a selection of experimental results is presented.

40 CFR 60.5195 - By what date must I conduct the initial air pollution control device inspection and make any...

Code of Federal Regulations, 2011 CFR

2011-07-01

... air pollution control device inspection and make any necessary repairs? 60.5195 Section 60.5195... air pollution control device inspection and make any necessary repairs? (a) You must conduct an air pollution control device inspection according to § 60.5220(c) by the final compliance date under the...

40 CFR 60.4895 - By what date must I conduct annual air pollution control device inspections and make any...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Compliance Requirements § 60.4895 By what date must I conduct annual air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution... following the previous annual air pollution control device inspection. (b) Within 10 operating days...

40 CFR 60.4895 - By what date must I conduct annual air pollution control device inspections and make any...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Compliance Requirements § 60.4895 By what date must I conduct annual air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution... following the previous annual air pollution control device inspection. (b) Within 10 operating days...

40 CFR 60.4895 - By what date must I conduct annual air pollution control device inspections and make any...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Compliance Requirements § 60.4895 By what date must I conduct annual air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution... following the previous annual air pollution control device inspection. (b) Within 10 operating days...

Application of total distributed control system in car-body inspection

NASA Astrophysics Data System (ADS)

Yang, Xueyou; Ren, Dahai; Wang, Zhong; Ye, Shenghua; Lu, Hongbo; Duan, Jilin

1996-08-01

An application of distributed control system in Autocar-body Visual Inspection Station is presented in the paper, a distributed control system using PC as the host processor and single-chip microcomputer as the slave controller is proposed. In this paper, the physical interface of the control network and the relevant hardware are introduced. Meanwhile, a minute research on data communication is performed, relevant protocols on data framing, instruction codes and channel access methods have been laid down and part of related software is presented.

Quality assurance and control in the production and static tests of the solid rocket boosters for the Space Shuttle

NASA Technical Reports Server (NTRS)

Cerny, O. F.

1979-01-01

The paper surveys the various aspects of design and overhaul of the solid rocket boosters. It is noted that quality control is an integral part of the design specifications. Attention is given to the production process which is optimized towards highest quality. Also discussed is the role of the DCA (Defense Contract Administration) in inspecting the products of subcontractors, noting that the USAF performs this role for prime contractors. Fabrication and construction of the booster is detailed with attention given to the lining of the booster cylinder and the mixing of the propellant and the subsequent X-ray inspection.

40 CFR 60.4895 - By what date must I conduct annual air pollution control device inspections and make any...

Code of Federal Regulations, 2011 CFR

2011-07-01

... pollution control device inspections and make any necessary repairs? 60.4895 Section 60.4895 Protection of... Compliance Requirements § 60.4895 By what date must I conduct annual air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution...

External inspection of compliance with standards for improved healthcare outcomes.

PubMed

Flodgren, Gerd; Gonçalves-Bradley, Daniela C; Pomey, Marie-Pascale

2016-12-02

Inspection systems are used in healthcare to promote quality improvements (i.e. to achieve changes in organisational structures or processes, healthcare provider behaviour and patient outcomes). These systems are based on the assumption that externally promoted adherence to evidence-based standards (through inspection/assessment) will result in higher quality of healthcare. However, the benefits of external inspection in terms of organisational-, provider- and patient-level outcomes are not clear. This is the first update of the original Cochrane review, published in 2011. To evaluate the effectiveness of external inspection of compliance with standards in improving healthcare organisation behaviour, healthcare professional behaviour and patient outcomes. We searched the following electronic databases for studies up to 1 June 2015: the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE, Embase, Database of Abstracts of Reviews of Effectiveness, HMIC, ClinicalTrials.gov and the World Health Organization International Clinical Trials Registry Platform. There was no language restriction and we included studies regardless of publication status. We also searched the reference lists of included studies and contacted authors of relevant papers, accreditation bodies and the International Organization for Standardization (ISO), regarding any further published or unpublished work. We also searched an online database of systematic reviews (PDQ-evidence.org). We included randomised controlled trials (RCTs), non-randomised trials (NRCTs), interrupted time series (ITSs) and controlled before-after studies (CBAs) evaluating the effect of external inspection against external standards on healthcare organisation change, healthcare professional behaviour or patient outcomes in hospitals, primary healthcare organisations and other community-based healthcare organisations. Two review authors independently applied eligibility criteria, extracted data and assessed the

33 CFR 203.43 - Inspection of Federal flood control works.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Inspection of Federal flood control works. 203.43 Section 203.43 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

33 CFR 203.43 - Inspection of Federal flood control works.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Inspection of Federal flood control works. 203.43 Section 203.43 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

33 CFR 203.43 - Inspection of Federal flood control works.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Inspection of Federal flood control works. 203.43 Section 203.43 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

33 CFR 203.43 - Inspection of Federal flood control works.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false Inspection of Federal flood control works. 203.43 Section 203.43 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

33 CFR 203.43 - Inspection of Federal flood control works.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Inspection of Federal flood control works. 203.43 Section 203.43 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

A collaborative vendor-buyer production-inventory systems with imperfect quality items, inspection errors, and stochastic demand under budget capacity constraint: a Karush-Kuhn-Tucker conditions approach

NASA Astrophysics Data System (ADS)

Kurdhi, N. A.; Nurhayati, R. A.; Wiyono, S. B.; Handajani, S. S.; Martini, T. S.

2017-01-01

In this paper, we develop an integrated inventory model considering the imperfect quality items, inspection error, controllable lead time, and budget capacity constraint. The imperfect items were uniformly distributed and detected on the screening process. However there are two types of possibilities. The first is type I of inspection error (when a non-defective item classified as defective) and the second is type II of inspection error (when a defective item classified as non-defective). The demand during the lead time is unknown, and it follows the normal distribution. The lead time can be controlled by adding the crashing cost. Furthermore, the existence of the budget capacity constraint is caused by the limited purchasing cost. The purposes of this research are: to modify the integrated vendor and buyer inventory model, to establish the optimal solution using Kuhn-Tucker’s conditions, and to apply the models. Based on the result of application and the sensitivity analysis, it can be obtained minimum integrated inventory total cost rather than separated inventory.

[Construction of NIRS-based total quality control system for compound Ejiao oral liquid and relative thinking].

PubMed

Zhang, Yan; Zhang, Lu; Tian, Shou-Sheng; Zhou, Xiang-Shan; Li, Wen-Long; Qu, Hai-Bin

2016-10-01

In this paper, near infrared spectroscopy (NIRS)-based total quality control system of compound Ejiao oral liquid is introduced briefly, including the quality control of raw traditional Chinese medicine (TCM) materials, monitoring and control of the extract and the alkaline precipitation technics, and also the inspection of finished products in both open bottle and non-opening modes. By analyzing and summing up the significance and difficulties, several important problems in the practical applications of NIRS technology are proposed, which will provide references for the similar studies of other TCM products. Copyright© by the Chinese Pharmaceutical Association.

48 CFR 46.301 - Contractor inspection requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Contractor inspection... CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Clauses 46.301 Contractor inspection requirements. The contracting officer shall insert the clause at 52.246-1, Contractor Inspection Requirements, in solicitations...

9 CFR 381.21 - Refusal of inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... conducted in a manner which will not violate the applicable water quality standards. No grant of inspection can be issued after April 3, 1970 (the date of enactment of the Water Quality Improvement Act), unless... required in connection with an application for inspection granted after April 3, 1970, for facilities...

14 CFR 135.429 - Required inspection personnel.

Code of Federal Regulations, 2011 CFR

2011-01-01

... item of work that is a required inspection item that is part of the flight control system shall be... supervision and control of an inspection unit. (c) No person may perform a required inspection if that person... maintenance program; (4) Each item is inspected after each flight until the item has been inspected by an...

14 CFR 135.429 - Required inspection personnel.

Code of Federal Regulations, 2014 CFR

2014-01-01

... item of work that is a required inspection item that is part of the flight control system shall be... supervision and control of an inspection unit. (c) No person may perform a required inspection if that person... maintenance program; (4) Each item is inspected after each flight until the item has been inspected by an...

14 CFR 135.429 - Required inspection personnel.

Code of Federal Regulations, 2013 CFR

2013-01-01

... item of work that is a required inspection item that is part of the flight control system shall be... supervision and control of an inspection unit. (c) No person may perform a required inspection if that person... maintenance program; (4) Each item is inspected after each flight until the item has been inspected by an...

14 CFR 135.429 - Required inspection personnel.

Code of Federal Regulations, 2012 CFR

2012-01-01

... item of work that is a required inspection item that is part of the flight control system shall be... supervision and control of an inspection unit. (c) No person may perform a required inspection if that person... maintenance program; (4) Each item is inspected after each flight until the item has been inspected by an...

14 CFR 135.429 - Required inspection personnel.

Code of Federal Regulations, 2010 CFR

2010-01-01

... item of work that is a required inspection item that is part of the flight control system shall be... supervision and control of an inspection unit. (c) No person may perform a required inspection if that person... maintenance program; (4) Each item is inspected after each flight until the item has been inspected by an...

Study on Classification Accuracy Inspection of Land Cover Data Aided by Automatic Image Change Detection Technology

NASA Astrophysics Data System (ADS)

Xie, W.-J.; Zhang, L.; Chen, H.-P.; Zhou, J.; Mao, W.-J.

2018-04-01

The purpose of carrying out national geographic conditions monitoring is to obtain information of surface changes caused by human social and economic activities, so that the geographic information can be used to offer better services for the government, enterprise and public. Land cover data contains detailed geographic conditions information, thus has been listed as one of the important achievements in the national geographic conditions monitoring project. At present, the main issue of the production of the land cover data is about how to improve the classification accuracy. For the land cover data quality inspection and acceptance, classification accuracy is also an important check point. So far, the classification accuracy inspection is mainly based on human-computer interaction or manual inspection in the project, which are time consuming and laborious. By harnessing the automatic high-resolution remote sensing image change detection technology based on the ERDAS IMAGINE platform, this paper carried out the classification accuracy inspection test of land cover data in the project, and presented a corresponding technical route, which includes data pre-processing, change detection, result output and information extraction. The result of the quality inspection test shows the effectiveness of the technical route, which can meet the inspection needs for the two typical errors, that is, missing and incorrect update error, and effectively reduces the work intensity of human-computer interaction inspection for quality inspectors, and also provides a technical reference for the data production and quality control of the land cover data.

Shipshape: sanitation inspections on cruise ships, 1990-2005, Vessel Sanitation Program, Centers for Disease Control and Prevention.

PubMed

Cramer, Elaine H; Blanton, Curtis J; Otto, Charles

2008-03-01

In the course of a successful collaboration between the Centers for Disease Control and Prevention (CDC) and the cruise ship industry on reducing common-source outbreaks, CDC's Vessel Sanitation Program (VSP) has expanded its training, education, and cruise ship inspection programs. The study reported here evaluated 15 years of ship sanitation inspection data from the National Center for Environmental Health and assessed performance in specific sanitation categories from 1996 to 2005. During the period 1990-2005, scores from cruise ship environmental sanitation inspections steadily improved. The percentage of inspections with violations decreased among five of nine categories. Those five categories were Washing Facilities, Contact Surfaces, Facility Maintenance, Food Handling, and Communicable Disease Practices. Inspection violations increased proportionally in the categories of Swimming Pools and Water System Protection/Chart Recording. Overall continued good performance in most sanitation categories is likely attributable to on-site training during inspections, improvements in ship construction, and a switch from hot-holding temperatures to time limits as a public health control for foods on display.

48 CFR 46.202-3 - Standard inspection requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Quality Requirements 46.202-3 Standard inspection... and tests while work is in process; and (3) Require the contractor to keep complete, and make available to the Government, records of its inspection work. [48 FR 42415, Sept. 19, 1983. Redesignated at...

48 CFR 46.202-3 - Standard inspection requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Quality Requirements 46.202-3 Standard inspection... and tests while work is in process; and (3) Require the contractor to keep complete, and make available to the Government, records of its inspection work. [48 FR 42415, Sept. 19, 1983. Redesignated at...

48 CFR 46.202-3 - Standard inspection requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Quality Requirements 46.202-3 Standard inspection... and tests while work is in process; and (3) Require the contractor to keep complete, and make available to the Government, records of its inspection work. [48 FR 42415, Sept. 19, 1983. Redesignated at...

48 CFR 46.202-3 - Standard inspection requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Quality Requirements 46.202-3 Standard inspection... and tests while work is in process; and (3) Require the contractor to keep complete, and make available to the Government, records of its inspection work. [48 FR 42415, Sept. 19, 1983. Redesignated at...

Enhanced automated spiral bevel gear inspection

NASA Technical Reports Server (NTRS)

Frint, Harold K.; Glasow, Warren

1992-01-01

Presented here are the results of a manufacturing and technology program to define, develop, and evaluate an enhanced inspection system for spiral bevel gears. The method uses a multi-axis coordinate measuring machine which maps the working surface of the tooth and compares it with nominal reference values stored in the machine's computer. The enhanced technique features a means for automatically calculating corrective grinding machine settings, involving both first and second order changes, to control the tooth profile to within specified tolerance limits. This enhanced method eliminates the subjective decision making involved in the tooth patterning method, still in use today, which compares contract patterns obtained when the gear is set to run under light load in a rolling test machine. It produces a higher quality gear with significant inspection time and cost savings.

Assessing risk factors in the organic control system: evidence from inspection data in Italy.

PubMed

Zanoli, Raffaele; Gambelli, Danilo; Solfanelli, Francesco

2014-12-01

Certification is an essential feature in organic farming, and it is based on inspections to verify compliance with respect to European Council Regulation-EC Reg. No 834/2007. A risk-based approach to noncompliance that alerts the control bodies to activate planning inspections would contribute to a more efficient and cost-effective certification system. An analysis of factors that can affect the probability of noncompliance in organic farming has thus been developed. This article examines the application of zero-inflated count data models to farm-level panel data from inspection results and sanctions obtained from the Ethical and Environmental Certification Institute, one of the main control bodies in Italy. We tested many a priori hypotheses related to the risk of noncompliance. We find evidence of an important role for past noncompliant behavior in predicting future noncompliance, while farm size and the occurrence of livestock also have roles in an increased probability of noncompliance. We conclude the article proposing that an efficient risk-based inspection system should be designed, weighting up the known probability of occurrence of a given noncompliance according to the severity of its impact. © 2014 Society for Risk Analysis.

76 FR 45397 - Export Inspection and Weighing Waiver for High Quality Specialty Grain Transported in Containers

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-29

... compared to an average $0.34 per metric ton for traditional grain exports. On December 13, 2005, GIPSA... mandatory inspection and weighing requirements of the USGSA that would adversely affect the marketing system... established the waiver to facilitate the marketing of high quality specialty grain by eliminating the burden...

Industrial applications of automated X-ray inspection

NASA Astrophysics Data System (ADS)

Shashishekhar, N.

2015-03-01

Many industries require that 100% of manufactured parts be X-ray inspected. Factors such as high production rates, focus on inspection quality, operator fatigue and inspection cost reduction translate to an increasing need for automating the inspection process. Automated X-ray inspection involves the use of image processing algorithms and computer software for analysis and interpretation of X-ray images. This paper presents industrial applications and illustrative case studies of automated X-ray inspection in areas such as automotive castings, fuel plates, air-bag inflators and tires. It is usually necessary to employ application-specific automated inspection strategies and techniques, since each application has unique characteristics and interpretation requirements.

46 CFR 160.053-4 - Inspections and tests.

Code of Federal Regulations, 2014 CFR

2014-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Work Vests, Unicellular Plastic Foam § 160.053-4 Inspections and.... (b) Manufacturer's inspections and tests. Manufacturers of approved work vests shall maintain quality... samples from each lot to maintain the quality of their product. (c) Lot size. A lot shall consist of not...

46 CFR 160.053-4 - Inspections and tests.

Code of Federal Regulations, 2013 CFR

2013-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Work Vests, Unicellular Plastic Foam § 160.053-4 Inspections and.... (b) Manufacturer's inspections and tests. Manufacturers of approved work vests shall maintain quality... samples from each lot to maintain the quality of their product. (c) Lot size. A lot shall consist of not...

46 CFR 160.053-4 - Inspections and tests.

Code of Federal Regulations, 2012 CFR

2012-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Work Vests, Unicellular Plastic Foam § 160.053-4 Inspections and.... (b) Manufacturer's inspections and tests. Manufacturers of approved work vests shall maintain quality... samples from each lot to maintain the quality of their product. (c) Lot size. A lot shall consist of not...

Continuous Ultrasonic Inspection of Extruded Wood-Plastic Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tucker, Brian J.; Bender, Donald A.

Nondestructive evaluation (NDE) techniques are needed for in-line monitoring of wood-plastic composite (WPC) quality during manufacturing for process control. Through-transmission ultrasonic inspection is useful in characterizing stiffness and detecting cracks and voids in a range of materials; however, little is documented about ultrasound propagation in WPC materials. The objectives of this research were to determine applicable ultrasonic transducer frequencies, coupling methods, configurations and placements for wave speed monitoring and web defect detection within an extrusion process; to quantify the effects of temperature on ultrasonic parameters; and to develop a prototype ultrasonic inspection system for a full-size extrusion line. An angledmore » beam, water-coupled ultrasonic inspection system using a pair of 50-kHz narrowband transducers was adequate for monitoring wave speed parallel to the extrusion direction. For locating internal web defects, water-coupled, 500-kHz broadband ultrasonic transducers were used in a through-thickness transmission setup. Temperature compensation factors were developed to adjust ultrasonic wave speed measurements. The prototype inspection system was demonstrated in a 55 mm conical twin-screw extrusion line.« less

40 CFR 60.5215 - By what date must I conduct annual air pollution control device inspections and make any...

Code of Federal Regulations, 2014 CFR

2014-07-01

... air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution control device used to comply with the emission limits, according to § 60.5220(c), no later than 12 months following the previous annual air pollution control device...

40 CFR 60.5215 - By what date must I conduct annual air pollution control device inspections and make any...

Code of Federal Regulations, 2013 CFR

2013-07-01

... air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution control device used to comply with the emission limits, according to § 60.5220(c), no later than 12 months following the previous annual air pollution control device...

40 CFR 60.5215 - By what date must I conduct annual air pollution control device inspections and make any...

Code of Federal Regulations, 2012 CFR

2012-07-01

... air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution control device used to comply with the emission limits, according to § 60.5220(c), no later than 12 months following the previous annual air pollution control device...

Nuclear Technology. Course 28: Welding Inspection. Module 28-8, Filler Metal Control.

ERIC Educational Resources Information Center

Espy, John

This eighth in a series of ten modules for a course titled Welding Inspection describes controls necessary to place the proper electrode or rod at each welding station. More specifically, the module describes use of the American Welding Society specifications, control of weld filler material after receipt from the supplier, and methods of ensuring…

Analyzing a Mature Software Inspection Process Using Statistical Process Control (SPC)

NASA Technical Reports Server (NTRS)

Barnard, Julie; Carleton, Anita; Stamper, Darrell E. (Technical Monitor)

1999-01-01

This paper presents a cooperative effort where the Software Engineering Institute and the Space Shuttle Onboard Software Project could experiment applying Statistical Process Control (SPC) analysis to inspection activities. The topics include: 1) SPC Collaboration Overview; 2) SPC Collaboration Approach and Results; and 3) Lessons Learned.

Implementing hospital quality assurance policies in Iran: balancing licensing, annual evaluation, inspections and quality management systems.

PubMed

Aghaei Hashjin, Asgar; Delgoshaei, Bahram; Kringos, Dionne S; Tabibi, Seyed Jamaladin; Manouchehri, Jila; Klazinga, Niek S

2015-01-01

The purpose of this paper is to provide an overview of applied hospital quality assurance (QA) policies in Iran. A mixed method (quantitative data and qualitative document analysis) study was carried out between 1996 and 2010. The QA policy cycle forms a tight monitoring system to assure hospital quality by combining mandatory and voluntary methods in Iran. The licensing, annual evaluation and grading, and regulatory inspections statutorily implemented by the government as a national package to assure and improve hospital care quality, while implementing quality management systems (QMS) was voluntary for hospitals. The government's strong QA policy legislation role and support has been an important factor for successful QA implementation in Iran, though it may affected QA assessment independency and validity. Increased hospital evaluation independency and repositioning, updating standards, professional involvement and effectiveness studies could increase QA policy impact and maturity. The study highlights the current QA policy implementation cycle in Iranian hospitals. It provides a basis for further quality strategy development in Iranian hospitals and elsewhere. It also raises attention about finding the optimal balance between different QA policies, which is topical for many countries. This paper describes experiences when implementing a unique approach, combining mandatory and voluntary QA policies simultaneously in a developing country, which has invested considerably over time to improve hospital quality. The experiences with a mixed obligatory/voluntary approach and comprehensive policies in Iran may contain lessons for policy makers in developing and developed countries.

Affordable housing and health: a health impact assessment on physical inspection frequency.

PubMed

Klein, Elizabeth G; Keller, Brittney; Hood, Nancy; Holtzen, Holly

2015-01-01

To characterize the prevalence of health-related housing quality exposure for the vulnerable populations that live in affordable housing. Retrospective cross-sectional study. Affordable housing properties in Ohio inspected between 2007 and 2011. Stratified random sample of physical inspection reports (n = 370), including a case study of properties receiving multiple inspections (n = 35). Health-related housing factors, including mold, fire hazard, and others. The majority of affordable housing property inspections (85.1%) included at least 1 health-related housing quality issue. The prevalence of specific health-related violations was varied, with appliance and plumbing issues being the most common, followed by fire, mold, and pest violations. Across funding agencies, the actual implementation of inspection protocols differed. The majority of physical inspections identified housing quality issues that have the potential to impact human health. If the frequency of physical inspections is reduced as a result of inspection alignment, the most health protective inspection protocol should be selected for funding agency inspections; a standardized physical inspection tool is recommended to improve the consistency of inspection findings between mandatory physical inspections in order to promote optimum tenant health.

Automated Inspection And Precise Grinding Of Gears

NASA Technical Reports Server (NTRS)

Frint, Harold; Glasow, Warren

1995-01-01

Method of precise grinding of spiral bevel gears involves automated inspection of gear-tooth surfaces followed by adjustments of machine-tool settings to minimize differences between actual and nominal surfaces. Similar to method described in "Computerized Inspection of Gear-Tooth Surfaces" (LEW-15736). Yields gears of higher quality, with significant reduction in manufacturing and inspection time.

System Enhancements for Mechanical Inspection Processes

NASA Technical Reports Server (NTRS)

Hawkins, Myers IV

2011-01-01

Quality inspection of parts is a major component to any project that requires hardware implementation. Keeping track of all of the inspection jobs is essential to having a smooth running process. By using HTML, the programming language ColdFusion, and the MySQL database, I created a web-based job management system for the 170 Mechanical Inspection Group that will replace the Microsoft Access based management system. This will improve the ways inspectors and the people awaiting inspection view and keep track of hardware as it is in the inspection process. In the end, the management system should be able to insert jobs into a queue, place jobs in and out of a bonded state, pre-release bonded jobs, and close out inspection jobs.

A Machine Vision Quality Control System for Industrial Acrylic Fibre Production

NASA Astrophysics Data System (ADS)

Heleno, Paulo; Davies, Roger; Correia, Bento A. Brázio; Dinis, João

2002-12-01

This paper describes the implementation of INFIBRA, a machine vision system used in the quality control of acrylic fibre production. The system was developed by INETI under a contract with a leading industrial manufacturer of acrylic fibres. It monitors several parameters of the acrylic production process. This paper presents, after a brief overview of the system, a detailed description of the machine vision algorithms developed to perform the inspection tasks unique to this system. Some of the results of online operation are also presented.

NDT applications in a successful fracture critical bridge inspection program and anchor bolt inspection program

NASA Astrophysics Data System (ADS)

Fish, Philip E.

1995-05-01

In 1978, Wisconsin Department of Transportation discovered major cracking on a two-girder, fracture critical structure, just four years after it was constructed. In 1981, on the same structure, now seven years old, major cracking was discovered in the tie girder flange of the tied arch span. This is one example of the type of failures that transportation departments discovered on welded structures in the 1970's and '80's. The failures from welded details and pinned connections lead to much stricter standards for present day designs. All areas were affected: design with identification of fatigue-prone details and classification of fatigue categories; material requirements with emphasis on toughness and weldability; increased welding and fabrication standards with licensure of fabrication shops to minimum quality standards including personnel; and an increased effort on inspection of existing bridges, where critical details were overlooked or missed in the past. FHWA inspection requirements for existing structures increased through this same time period, in reaction to the failures that had occurred. Obviously, many structures in Wisconsin were not built to the standards now required, thus the importance for quality inspection techniques. The new FHWA inspection requirements now being implemented throughout the nation require an in-depth, hands-on type inspection at a specified frequency, on all fracture critical structures. Wisconsin Department of Transportation started an in-depth inspection program in 1985 and made it a full time program in 1987. This program included extensive nondestructive testing. Ultrasonic inspection has played a major role in this type of inspection. All fracture critical structures, pin and hanger systems, and pinned connections are inspected on a five-year cycle now. The program requires an experienced inspection team and a practical inspection approach. Extensive preparation is required with review of all design, construction, and

48 CFR 846.302-71 - Inspection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Inspection. 846.302-71 Section 846.302-71 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Clauses 846.302-71 Inspection. The contracting officer shall include a...

33 CFR 203.42 - Inspection of non-Federal flood control works.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Inspection of non-Federal flood control works. 203.42 Section 203.42 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

33 CFR 203.42 - Inspection of non-Federal flood control works.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false Inspection of non-Federal flood control works. 203.42 Section 203.42 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

33 CFR 203.42 - Inspection of non-Federal flood control works.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Inspection of non-Federal flood control works. 203.42 Section 203.42 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

33 CFR 203.42 - Inspection of non-Federal flood control works.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Inspection of non-Federal flood control works. 203.42 Section 203.42 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY EMPLOYMENT OF ARMY AND OTHER RESOURCES, NATURAL DISASTER...

49 CFR 179.7 - Quality assurance program.

Code of Federal Regulations, 2010 CFR

2010-10-01

... means to detect any nonconformity in the manufacturing, repair, inspection, testing, and qualification... quality control personnel. (3) Procedures to ensure that the latest applicable drawings, design calculations, specifications, and instructions are used in manufacture, inspection, testing, and repair. (4...

46 CFR 162.028-6 - Examinations, tests, and inspections.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Examinations, tests, and inspections. 162.028-6 Section... Type § 162.028-6 Examinations, tests, and inspections. (a) Full examinations, tests, and inspections to..., inspections, and tests as to satisfy himself that the quality assurance program of the manufacturer is...

Incorporating Quality Control Information in the Sensor Web

NASA Astrophysics Data System (ADS)

Devaraju, Anusuriya; Kunkel, Ralf; Bogena, Heye

2013-04-01

The rapid development of sensing technologies had led to the creation of large amounts of heterogeneous environmental observations. The Sensor Web provides a wider access to sensors and observations via common protocols and specifications. Observations typically go through several levels of quality control, and aggregation before they are made available to end-users. Raw data are usually inspected, and related quality flags are assigned. Data are gap-filled, and errors are removed. New data series may also be derived from one or more corrected data sets. Until now, it is unclear how these kinds of information can be captured in the Sensor Web Enablement (SWE) framework. Apart from the quality measures (e.g., accuracy, precision, tolerance, or confidence), the levels of observational series, the changes applied, and the methods involved must be specified. It is important that this kind of quality control information is well described and communicated to end-users to allow for a better usage and interpretation of data products. In this paper, we describe how quality control information can be incorporated into the SWE framework. Concerning this, first, we introduce the TERENO (TERrestrial ENvironmental Observatories), an initiative funded by the large research infrastructure program of the Helmholtz Association in Germany. The main goal of the initiative is to facilitate the study of long-term effects of climate and land use changes. The TERENO Online Data RepOsitORry (TEODOOR) is a software infrastructure that supports acquisition, provision, and management of observations within TERENO via SWE specifications and several other OGC web services. Next, we specify changes made to the existing observational data model to incorporate quality control information. Here, we describe the underlying TERENO data policy in terms of provision and maintenance issues. We present data levels, and their implementation within TEODOOR. The data levels are adapted from those used by

40 CFR 60.5195 - By what date must I conduct the initial air pollution control device inspection and make any...

Code of Federal Regulations, 2014 CFR

2014-07-01

... air pollution control device inspection and make any necessary repairs? 60.5195 Section 60.5195... air pollution control device inspection and make any necessary repairs? (a) You must conduct an air... approved state plan, Federal plan, or delegation, as applicable. For air pollution control devices...

40 CFR 60.5195 - By what date must I conduct the initial air pollution control device inspection and make any...

Code of Federal Regulations, 2013 CFR

2013-07-01

... air pollution control device inspection and make any necessary repairs? 60.5195 Section 60.5195... air pollution control device inspection and make any necessary repairs? (a) You must conduct an air... approved state plan, Federal plan, or delegation, as applicable. For air pollution control devices...

40 CFR 60.5195 - By what date must I conduct the initial air pollution control device inspection and make any...

Code of Federal Regulations, 2012 CFR

2012-07-01

... air pollution control device inspection and make any necessary repairs? 60.5195 Section 60.5195... air pollution control device inspection and make any necessary repairs? (a) You must conduct an air... approved state plan, Federal plan, or delegation, as applicable. For air pollution control devices...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2013 CFR

2013-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

Modeling and control of a cable-suspended robot for inspection of vertical structures

NASA Astrophysics Data System (ADS)

Barry, Nicole; Fisher, Erin; Vaughan, Joshua

2016-09-01

In this paper, a cable-driven system is examined for the application of inspection of large, vertical-walled structures such as chemical storage tanks, large ship hulls, and high-rise buildings. Such cable-driven systems are not commonly used for these tasks due to vibration, which decreases inspection accuracy and degrades safety. The flexible nature of the cables make them difficult to control. In this paper, input shaping is implemented on a cable-driven system to reduce vibration. To design the input shapers, a model of the cable-driven system was developed. Analysis of the dominant dynamics and changes in them over the large workspace are also presented. The performance improvements provided by the input shaping controller are quantified through a series of simulations.

7 CFR 868.91 - Fees for certain Federal rice inspection services.

Code of Federal Regulations, 2010 CFR

2010-01-01

...—Unit Rates Service 1 Effective February 16, 2007 Inspection for quality (per lot, sublot, or sample... other factors (per factor) (all rice) 15.60 Total oil and free fatty acid 50.80 Interpretive line... Effective October 1, 2007 Inspection for quality (per lot, sublot, or sample inspection): (a) Rough rice $43...

7 CFR 868.91 - Fees for certain Federal rice inspection services.

Code of Federal Regulations, 2011 CFR

2011-01-01

...—Unit Rates Service 1 Effective February 16, 2007 Inspection for quality (per lot, sublot, or sample... other factors (per factor) (all rice) 15.60 Total oil and free fatty acid 50.80 Interpretive line... Effective October 1, 2007 Inspection for quality (per lot, sublot, or sample inspection): (a) Rough rice $43...

Fully Employing Software Inspections Data

NASA Technical Reports Server (NTRS)

Shull, Forrest; Feldmann, Raimund L.; Seaman, Carolyn; Regardie, Myrna; Godfrey, Sally

2009-01-01

Software inspections provide a proven approach to quality assurance for software products of all kinds, including requirements, design, code, test plans, among others. Common to all inspections is the aim of finding and fixing defects as early as possible, and thereby providing cost savings by minimizing the amount of rework necessary later in the lifecycle. Measurement data, such as the number and type of found defects and the effort spent by the inspection team, provide not only direct feedback about the software product to the project team but are also valuable for process improvement activities. In this paper, we discuss NASA's use of software inspections and the rich set of data that has resulted. In particular, we present results from analysis of inspection data that illustrate the benefits of fully utilizing that data for process improvement at several levels. Examining such data across multiple inspections or projects allows team members to monitor and trigger cross project improvements. Such improvements may focus on the software development processes of the whole organization as well as improvements to the applied inspection process itself.

40 CFR 60.4875 - By what date must I conduct the initial air pollution control device inspection and make any...

Code of Federal Regulations, 2011 CFR

2011-07-01

... air pollution control device inspection and make any necessary repairs? 60.4875 Section 60.4875... Initial Compliance Requirements § 60.4875 By what date must I conduct the initial air pollution control device inspection and make any necessary repairs? (a) You must conduct an air pollution control device...

40 CFR 60.4875 - By what date must I conduct the initial air pollution control device inspection and make any...

Code of Federal Regulations, 2014 CFR

2014-07-01

... air pollution control device inspection and make any necessary repairs? 60.4875 Section 60.4875... Initial Compliance Requirements § 60.4875 By what date must I conduct the initial air pollution control device inspection and make any necessary repairs? (a) You must conduct an air pollution control device...

40 CFR 60.4875 - By what date must I conduct the initial air pollution control device inspection and make any...

Code of Federal Regulations, 2013 CFR

2013-07-01

... air pollution control device inspection and make any necessary repairs? 60.4875 Section 60.4875... Initial Compliance Requirements § 60.4875 By what date must I conduct the initial air pollution control device inspection and make any necessary repairs? (a) You must conduct an air pollution control device...

40 CFR 60.4875 - By what date must I conduct the initial air pollution control device inspection and make any...

Code of Federal Regulations, 2012 CFR

2012-07-01

... air pollution control device inspection and make any necessary repairs? 60.4875 Section 60.4875... Initial Compliance Requirements § 60.4875 By what date must I conduct the initial air pollution control device inspection and make any necessary repairs? (a) You must conduct an air pollution control device...

Device for inspecting vessel surfaces

DOEpatents

Appel, D. Keith

1995-01-01

A portable, remotely-controlled inspection crawler for use along the walls of tanks, vessels, piping and the like. The crawler can be configured to use a vacuum chamber for supporting itself on the inspected surface by suction or a plurality of magnetic wheels for moving the crawler along the inspected surface. The crawler is adapted to be equipped with an ultrasonic probe for mapping the structural integrity or other characteristics of the surface being inspected. Navigation of the crawler is achieved by triangulation techniques between a signal transmitter on the crawler and a pair of microphones attached to a fixed, remote location, such as the crawler's deployment unit. The necessary communications are established between the crawler and computers external to the inspection environment for position control and storage and/or monitoring of data acquisition.

QCScreen: a software tool for data quality control in LC-HRMS based metabolomics.

PubMed

Simader, Alexandra Maria; Kluger, Bernhard; Neumann, Nora Katharina Nicole; Bueschl, Christoph; Lemmens, Marc; Lirk, Gerald; Krska, Rudolf; Schuhmacher, Rainer

2015-10-24

Metabolomics experiments often comprise large numbers of biological samples resulting in huge amounts of data. This data needs to be inspected for plausibility before data evaluation to detect putative sources of error e.g. retention time or mass accuracy shifts. Especially in liquid chromatography-high resolution mass spectrometry (LC-HRMS) based metabolomics research, proper quality control checks (e.g. for precision, signal drifts or offsets) are crucial prerequisites to achieve reliable and comparable results within and across experimental measurement sequences. Software tools can support this process. The software tool QCScreen was developed to offer a quick and easy data quality check of LC-HRMS derived data. It allows a flexible investigation and comparison of basic quality-related parameters within user-defined target features and the possibility to automatically evaluate multiple sample types within or across different measurement sequences in a short time. It offers a user-friendly interface that allows an easy selection of processing steps and parameter settings. The generated results include a coloured overview plot of data quality across all analysed samples and targets and, in addition, detailed illustrations of the stability and precision of the chromatographic separation, the mass accuracy and the detector sensitivity. The use of QCScreen is demonstrated with experimental data from metabolomics experiments using selected standard compounds in pure solvent. The application of the software identified problematic features, samples and analytical parameters and suggested which data files or compounds required closer manual inspection. QCScreen is an open source software tool which provides a useful basis for assessing the suitability of LC-HRMS data prior to time consuming, detailed data processing and subsequent statistical analysis. It accepts the generic mzXML format and thus can be used with many different LC-HRMS platforms to process both multiple

Framework for Automated GD&T Inspection Using 3D Scanner

NASA Astrophysics Data System (ADS)

Pathak, Vimal Kumar; Singh, Amit Kumar; Sivadasan, M.; Singh, N. K.

2018-04-01

Geometric Dimensioning and Tolerancing (GD&T) is a typical dialect that helps designers, production faculty and quality monitors to convey design specifications in an effective and efficient manner. GD&T has been practiced since the start of machine component assembly but without overly naming it. However, in recent times industries have started increasingly emphasizing on it. One prominent area where most of the industries struggle with is quality inspection. Complete inspection process is mostly human intensive. Also, the use of conventional gauges and templates for inspection purpose highly depends on skill of workers and quality inspectors. In industries, the concept of 3D scanning is not new but is used only for creating 3D drawings or modelling of physical parts. However, the potential of 3D scanning as a powerful inspection tool is hardly explored. This study is centred on designing a procedure for automated inspection using 3D scanner. Linear, geometric and dimensional inspection of the most popular test bar-stepped bar, as a simple example was also carried out as per the new framework. The new generation engineering industries would definitely welcome this automated inspection procedure being quick and reliable with reduced human intervention.

Built-in-test by signature inspection (bitsi)

DOEpatents

Bergeson, Gary C.; Morneau, Richard A.

1991-01-01

A system and method for fault detection for electronic circuits. A stimulus generator sends a signal to the input of the circuit under test. Signature inspection logic compares the resultant signal from test nodes on the circuit to an expected signal. If the signals do not match, the signature inspection logic sends a signal to the control logic for indication of fault detection in the circuit. A data input multiplexer between the test nodes of the circuit under test and the signature inspection logic can provide for identification of the specific node at fault by the signature inspection logic. Control logic responsive to the signature inspection logic conveys information about fault detection for use in determining the condition of the circuit. When used in conjunction with a system test controller, the built-in test by signature inspection system and method can be used to poll a plurality of circuits automatically and continuous for faults and record the results of such polling in the system test controller.

Inspection and characterization of flexo-printing plates

NASA Astrophysics Data System (ADS)

Hahlweg, Cornelius; Pescoller, Lukas; Zhao, Wenjing

2013-09-01

In continuation of last year's paper on distorting optics for inspection of 2 1/2D surfaces with convex or elevated elements - like braille paper and other special printing products - the present paper is dedicated to the quality control and characterization of flexo-printing plates. The need for high optical resolution contradicts the need for depth of field. A rugged optical system for gathering a series of microscopic images at various planes of focus is discussed.

Effect of X-ray exposure on the pharmaceutical quality of drug tablets using X-ray inspection equipment.

PubMed

Uehara, Kazuaki; Tagami, Tatsuaki; Miyazaki, Itaru; Murata, Norikazu; Takahashi, Yoshifumi; Ohkubo, Hiroshi; Ozeki, Tetsuya

2015-06-01

X-ray inspection equipment is widely used to detect missing materials and defective goods in opaque containers. Its application has been expanded to the pharmaceutical industry to detect the presence of drug tablets in aluminum foil press-through packaging. However, the effect of X-rays on the pharmaceutical quality of drug tablets is not well known. In this study, the effect of X-rays on the pharmaceutical quality of drug tablets was investigated. Exposure of acetaminophen, loxoprofen and mefenamic acid tablets to X-ray doses of 0.34 mGy (thrice the dose by X-ray scanning) to 300 Gy (maximum dose from our X-ray equipment) was demonstrated, and the samples were evaluated by formulation tests. Exposure to X-rays did not affect the pharmaceutical quality of the drug content. The samples exposed to X-rays exhibited almost the same profile in formulation tests (dissolution test, disintegrating test and hardness test) as control samples (0 Gy). The combination of X-ray exposure with accelerated temperature and humidity tests (six months) also did not affect the pharmaceutical quality. The color change of light-sensitive drugs (nifedipine and furosemide tablets) after X-ray exposure was negligible (< 1.0). In contrast, tablet color was remarkably changed by light from a D65 lamp. The X-ray scanning and X-ray exposure under our experimental conditions did not affect the pharmaceutical quality of drug tablets.

48 CFR 446.370 - Inspection and acceptance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Inspection and acceptance. 446.370 Section 446.370 Federal Acquisition Regulations System DEPARTMENT OF AGRICULTURE CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Clauses 446.370 Inspection and acceptance. The Contracting Officer...

48 CFR 546.302-72 - Destination inspection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Destination inspection. 546.302-72 Section 546.302-72 Federal Acquisition Regulations System GENERAL SERVICES ADMINISTRATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Clauses 546.302-72 Destination inspection. The contracting...

A PLM-based automated inspection planning system for coordinate measuring machine

NASA Astrophysics Data System (ADS)

Zhao, Haibin; Wang, Junying; Wang, Boxiong; Wang, Jianmei; Chen, Huacheng

2006-11-01

With rapid progress of Product Lifecycle Management (PLM) in manufacturing industry, automatic generation of inspection planning of product and the integration with other activities in product lifecycle play important roles in quality control. But the techniques for these purposes are laggard comparing with techniques of CAD/CAM. Therefore, an automatic inspection planning system for Coordinate Measuring Machine (CMM) was developed to improve the automatization of measuring based on the integration of inspection system in PLM. Feature information representation is achieved based on a PLM canter database; measuring strategy is optimized through the integration of multi-sensors; reasonable number and distribution of inspection points are calculated and designed with the guidance of statistic theory and a synthesis distribution algorithm; a collision avoidance method is proposed to generate non-collision inspection path with high efficiency. Information mapping is performed between Neutral Interchange Files (NIFs), such as STEP, DML, DMIS, XML, etc., to realize information integration with other activities in the product lifecycle like design, manufacturing and inspection execution, etc. Simulation was carried out to demonstrate the feasibility of the proposed system. As a result, the inspection process is becoming simpler and good result can be got based on the integration in PLM.

7 CFR 944.400 - Designated inspection services and procedure for obtaining inspection and certification of...

Code of Federal Regulations, 2011 CFR

2011-01-01

..., quality, and maturity of avocados, grapefruit, nectarines, oranges, prune variety plums (fresh prunes... designated as a governmental inspection service for the purpose of certifying grade, size, quality and... New Mexico, Officer In Charge, New Mexico Market and Development Branch, New Mexico Department of...

Implementation of basic quality control tests for malaria medicines in Amazon Basin countries: results for the 2005-2010 period.

PubMed

Pribluda, Victor S; Barojas, Adrian; Añez, Arletta; López, Cecilia G; Figueroa, Ruth; Herrera, Roxana; Nakao, Gladys; Nogueira, Fernando Ha; Pianetti, Gerson A; Povoa, Marinete M; Viana, Giselle Mr; Gomes, Margarete S Mendonça; Escobar, Jose P; Sierra, Olga L Muñoz; Norena, Susana P Rendon; Veloz, Raúl; Bravo, Marcy Silva; Aldás, Martha R; Hindssemple, Alison; Collins, Marilyn; Ceron, Nicolas; Krishnalall, Karanchand; Adhin, Malti; Bretas, Gustavo; Hernandez, Nelly; Mendoza, Marjorie; Smine, Abdelkrim; Chibwe, Kennedy; Lukulay, Patrick; Evans, Lawrence

2012-06-15

Ensuring the quality of malaria medicines is crucial in working toward malaria control and eventual elimination. Unlike other validated tests that can assess all critical quality attributes, which is the standard for determining the quality of medicines, basic tests are significantly less expensive, faster, and require less skilled labour; yet, these tests provide reproducible data and information on several critical quality attributes, such as identity, purity, content, and disintegration. Visual and physical inspection also provides valuable information about the manufacturing and the labelling of medicines, and in many cases this inspection is sufficient to detect counterfeit medicines. The Promoting the Quality of Medicines (PQM) programme has provided technical assistance to Amazon Malaria Initiative (AMI) countries to implement the use of basic tests as a key screening mechanism to assess the quality of malaria medicines available to patients in decentralized regions. Trained personnel from the National Malaria Control Programmes (NMCPs), often in collaboration with country's Official Medicine Control Laboratory (OMCL), developed country- specific protocols that encompassed sampling methods, sample analysis, and data reporting. Sampling sites were selected based on malaria burden, accessibility, and geographical location. Convenience sampling was performed and countries were recommended to store the sampled medicines under conditions that did not compromise their quality. Basic analytical tests, such as disintegration and thin layer chromatography (TLC), were performed utilizing a portable mini-laboratory. Results were originally presented at regional meetings in a non-standardized format that lacked relevant medicines information. However, since 2008 information has been submitted utilizing a template specifically developed by PQM for that purpose. From 2005 to 2010, the quality of 1,663 malaria medicines from seven AMI countries was evaluated, mostly

48 CFR 546.302-71 - Source inspection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Source inspection. 546.302-71 Section 546.302-71 Federal Acquisition Regulations System GENERAL SERVICES ADMINISTRATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Clauses 546.302-71 Source inspection. For solicitations and contracts...

46 CFR 162.039-6 - Examinations, tests, and inspections.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Examinations, tests, and inspections. 162.039-6 Section..., Marine Type § 162.039-6 Examinations, tests, and inspections. (a) Full examinations, tests, and... such examinations, inspections, and tests as to satisfy himself that the quality assurance program of...

Device for inspecting vessel surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Appel, D.K.

1995-12-12

A portable, remotely-controlled inspection crawler is described for use along the walls of tanks, vessels, piping and the like. The crawler can be configured to use a vacuum chamber for supporting itself on the inspected surface by suction or a plurality of magnetic wheels for moving the crawler along the inspected surface. The crawler is adapted to be equipped with an ultrasonic probe for mapping the structural integrity or other characteristics of the surface being inspected. Navigation of the crawler is achieved by triangulation techniques between a signal transmitter on the crawler and a pair of microphones attached to amore » fixed, remote location, such as the crawler`s deployment unit. The necessary communications are established between the crawler and computers external to the inspection environment for position control and storage and/or monitoring of data acquisition. 5 figs.« less

Surface inspection: Research and development

NASA Technical Reports Server (NTRS)

Batchelder, J. S.

1987-01-01

Surface inspection techniques are used for process learning, quality verification, and postmortem analysis in manufacturing for a spectrum of disciplines. First, trends in surface analysis are summarized for integrated circuits, high density interconnection boards, and magnetic disks, emphasizing on-line applications as opposed to off-line or development techniques. Then, a closer look is taken at microcontamination detection from both a patterned defect and a particulate inspection point of view.

Airborne ultrasonic inspection of hides and leather

USDA-ARS?s Scientific Manuscript database

Currently, hides and leather are visually inspected and ranked for quality, sale price and usable area. Visual inspection is not reliable for detecting defects, which are usually hidden inside the material. This manual assessment is non-uniform among operators, and often leads to disputes over fai...

18 CFR 12.32 - General inspection requirement.

Code of Federal Regulations, 2012 CFR

2012-04-01

... the condition of those project works or in the quality or adequacy of project maintenance... PROJECT WORKS Inspection by Independent Consultant § 12.32 General inspection requirement. In accordance with the procedures in § 12.35, the project works of each development to which this subpart applies...

18 CFR 12.32 - General inspection requirement.

Code of Federal Regulations, 2014 CFR

2014-04-01

... the condition of those project works or in the quality or adequacy of project maintenance... PROJECT WORKS Inspection by Independent Consultant § 12.32 General inspection requirement. In accordance with the procedures in § 12.35, the project works of each development to which this subpart applies...

18 CFR 12.32 - General inspection requirement.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the condition of those project works or in the quality or adequacy of project maintenance... PROJECT WORKS Inspection by Independent Consultant § 12.32 General inspection requirement. In accordance with the procedures in § 12.35, the project works of each development to which this subpart applies...

Effectiveness of external inspection of compliance with standards in improving healthcare organisation behaviour, healthcare professional behaviour or patient outcomes

PubMed Central

Flodgren, Gerd; Pomey, Marie-Pascale; Taber, Sarah A; Eccles, Martin P

2014-01-01

Background Inspection systems are used in health care to promote quality improvements, i.e. to achieve changes in organisational structures or processes, healthcare provider behaviour and patient outcomes. These systems are based on the assumption that externally promoted adherence to evidence-based standards (through inspection/assessment) will result in higher quality of health care. However, the benefits of external inspection in terms of organisational, provider and patient level outcomes are not clear. Objectives To evaluate the effectiveness of external inspection of compliance with standards in improving healthcare organisation behaviour, healthcare professional behaviour and patient outcomes. Search methods We searched the following electronic databases for studies: the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE, EMBASE, CINAHL, Cochrane Database of Systematic Reviews, Database of Abstracts of Reviews of Effectiveness, Scopus, HMIC, Index to Theses and Intute from their inception dates up to May 2011. There was no language restriction and studies were included regardless of publication status. We searched the reference lists of included studies and contacted authors of relevant papers, accreditation bodies and the International Organization for Standardisation (ISO), regarding any further published or unpublished work. Selection criteria We included randomised controlled trials (RCTs), controlled clinical trials (CCTs), interrupted time-series (ITSs) and controlled before and after studies (CBAs) evaluating the effect of external inspection against external standards on healthcare organisation change, healthcare professional behaviour or patient outcomes in hospitals, primary healthcare organisations and other community-based healthcare organisations. Data collection and analysis Two review authors independently applied eligibility criteria, extracted data and assessed the risk of bias of each included study. Since meta-analysis was

Resonant frequency method for bearing ball inspection

DOEpatents

Khuri-Yakub, B.T.; Chungkao Hsieh.

1993-11-02

The present invention provides for an inspection system and method for detecting defects in test objects which includes means for generating expansion inducing energy focused upon the test object at a first location, such expansion being allowed to contract, thereby causing pressure wave within and on the surface of the test object. Such expansion inducing energy may be provided by, for example, a laser beam or ultrasonic energy. At a second location, the amplitudes and phases of the acoustic waves are detected and the resonant frequencies' quality factors are calculated and compared to predetermined quality factor data, such comparison providing information of whether the test object contains a defect. The inspection system and method also includes means for mounting the bearing ball for inspection. 5 figures.

Resonant frequency method for bearing ball inspection

DOEpatents

Khuri-Yakub, B. T.; Hsieh, Chung-Kao

1993-01-01

The present invention provides for an inspection system and method for detecting defects in test objects which includes means for generating expansion inducing energy focused upon the test object at a first location, such expansion being allowed to contract, thereby causing pressure wave within and on the surface of the test object. Such expansion inducing energy may be provided by, for example, a laser beam or ultrasonic energy. At a second location, the amplitudes and phases of the acoustic waves are detected and the resonant frequencies' quality factors are calculated and compared to predetermined quality factor data, such comparison providing information of whether the test object contains a defect. The inspection system and method also includes means for mounting the bearing ball for inspection.

Nuclear Technology. Course 28: Welding Inspection. Module 28-9, Weld Repair Control.

ERIC Educational Resources Information Center

Espy, John

This ninth in a series of ten modules for a course titled Welding Inspection describes the purposes, essential elements, and application of a weld control program. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4) notes to instructor/student, (5) subject…

PF-WFS Shell Inspection Update December 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vigil, Anthony Eugene; Ledoux, Reina Rebecca; Gonzales, Antonio R.

Since the last project update in FY16:Q2, PF-WFS personnel have advanced in understanding of shell inspection on Coordinate Measuring Machines {CMM} and refined the PF-WFS process to the point it was decided to convert shell inspection from the Sheffield #1 gage to Lietz CM Ms. As a part of introspection on the quality of this process many sets of data have been reviewed and analyzed. This analysis included Sheffield to CMM comparisons, CMM inspection repeatability, fixturing differences, quality check development, probing approach changes. This update report will touch on these improvements that have built the confidence in this process tomore » mainstream it inspecting shells. In addition to the CMM programming advancements, the continuation in refinement of input and outputs for the CMM program has created an archiving scheme, input spline files, an output metafile, and inspection report package. This project will continue to mature. Part designs may require program modifications to accommodate "new to this process" part designs. Technology limitations tied to security and performance are requiring possible changes to computer configurations to support an automated process.« less

Projector-Based Augmented Reality for Quality Inspection of Scanned Objects

NASA Astrophysics Data System (ADS)

Kern, J.; Weinmann, M.; Wursthorn, S.

2017-09-01

After scanning or reconstructing the geometry of objects, we need to inspect the result of our work. Are there any parts missing? Is every detail covered in the desired quality? We typically do this by looking at the resulting point clouds or meshes of our objects on-screen. What, if we could see the information directly visualized on the object itself? Augmented reality is the generic term for bringing virtual information into our real environment. In our paper, we show how we can project any 3D information like thematic visualizations or specific monitoring information with reference to our object onto the object's surface itself, thus augmenting it with additional information. For small objects that could for instance be scanned in a laboratory, we propose a low-cost method involving a projector-camera system to solve this task. The user only needs a calibration board with coded fiducial markers to calibrate the system and to estimate the projector's pose later on for projecting textures with information onto the object's surface. Changes within the projected 3D information or of the projector's pose will be applied in real-time. Our results clearly reveal that such a simple setup will deliver a good quality of the augmented information.

Improving NGDC Track-line Data Quality Control

NASA Astrophysics Data System (ADS)

Chandler, M. T.; Wessel, P.

2004-12-01

Ship-board gravity, magnetic and bathymetry data archived at the National Geophysical Data Center (NGDC) represent decades of seagoing research, containing over 4,500 cruises. Cruise data remain relevent despite the prominence of satellite altimetry-derived global grids because many geologic processes remain resolvable by oceanographic research alone. Due to the tremendous investment put forth by scientists and taxpayers to compile this vast archive and the significant errors found within it, additional quality assessment and corrections are warranted. These can best be accomplished by adding to existing quality control measures at NGDC. We are currently developing open source software to provide additional quality control. Along with NGDC's current sanity checking, new data at NGDC will also be subjected to an along-track ``sniffer'' which will detect and flag suspicious data for later graphical inspection using a visual editor. If new data pass these tests, they will undergo further scrutinization using a crossover error (COE) calculator which will compare new data values to existing values at points of intersection within the archive. Data passing these tests will be deemed ``quality data`` and suitable for permanent addition to the archive, while data that fail will be returned to the source institution for correction. Crossover errors will be stored and an online COE database will be available. The COE database will allow users to apply corrections to the NGDC track-line database to produce corrected data files. At no time will the archived data itself be modified. An attempt will also be made to reduce navigational errors for pre-GPS navigated cruises. Upon completion these programs will be used to explore and model systematic errors within the archive, generate correction tables for all cruises, and to quantify the error budget in marine geophysical observations. Software will be released and these procedures will be implemented in cooperation with NGDC

Weld quality inspection using laser-EMAT ultrasonic system and C-scan method

NASA Astrophysics Data System (ADS)

Yang, Lei; Ume, I. Charles

2014-02-01

Laser/EMAT ultrasonic technique has attracted more and more interests in weld quality inspection because of its non-destructive and non-contact characteristics. When ultrasonic techniques are used to detect welds joining relative thin plates, the dominant ultrasonic waves present in the plates are Lamb waves, which propagate all through the thickness. Traditional Time of Flight(ToF) method loses its power. The broadband nature of laser excited ultrasound plus dispersive and multi-modal characteristic of Lamb waves make the EMAT acquired signals very complicated in this situation. Challenge rises in interpreting the received signals and establishing relationship between signal feature and weld quality. In this paper, the laser/EMAT ultrasonic technique was applied in a C-scan manner to record full wave propagation field over an area close to the weld. Then the effect of weld defect on the propagation field of Lamb waves was studied visually by watching an movie resulted from the recorded signals. This method was proved to be effective to detect the presence of hidden defect in the weld. Discrete wavelet transform(DWT) was applied to characterize the acquired ultrasonic signals and ideal band-pass filter was used to isolate wave components most sensitive to the weld defect. Different interactions with the weld defect were observed for different wave components. Thus this C-Scan method, combined with DWT and ideal band-pass filter, proved to be an effective methodology to experimentally study interactions of various laser excited Lamb Wave components with weld defect. In this work, the method was demonstrated by inspecting a hidden local incomplete penetration in weld. In fact, this method can be applied to study Lamb Wave interactions with any type of structural inconsistency. This work also proposed a ideal filtered based method to effectively reduce the total experimental time.

Quality inspection guided laser processing of irregular shape objects by stereo vision measurement: application in badminton shuttle manufacturing

NASA Astrophysics Data System (ADS)

Qi, Li; Wang, Shun; Zhang, Yixin; Sun, Yingying; Zhang, Xuping

2015-11-01

The quality inspection process is usually carried out after first processing of the raw materials such as cutting and milling. This is because the parts of the materials to be used are unidentified until they have been trimmed. If the quality of the material is assessed before the laser process, then the energy and efforts wasted on defected materials can be saved. We proposed a new production scheme that can achieve quantitative quality inspection prior to primitive laser cutting by means of three-dimensional (3-D) vision measurement. First, the 3-D model of the object is reconstructed by the stereo cameras, from which the spatial cutting path is derived. Second, collaborating with another rear camera, the 3-D cutting path is reprojected to both the frontal and rear views of the object and thus generates the regions-of-interest (ROIs) for surface defect analysis. An accurate visual guided laser process and reprojection-based ROI segmentation are enabled by a global-optimization-based trinocular calibration method. The prototype system was built and tested with the processing of raw duck feathers for high-quality badminton shuttle manufacture. Incorporating with a two-dimensional wavelet-decomposition-based defect analysis algorithm, both the geometrical and appearance features of the raw feathers are quantified before they are cut into small patches, which result in fully automatic feather cutting and sorting.

Noncontacting Optical Measurement And Inspection Systems

NASA Astrophysics Data System (ADS)

Asher, Jeffrey A.; Jackson, Robert L.

1986-10-01

Product inspection continues to play a growing role in the improvement of quality and reduction of scrap. Recent emphasis on precision measurements and in-process inspection have been a driving force for the development of noncontacting sensors. Noncontacting sensors can provide long term, unattended use due to the lack of sensor wear. Further, in applications where, sensor contact can damage or geometrically change the part to be measured or inspected, noncontacting sensors are the only technical approach available. MTI is involved in the development and sale of noncontacting sensors and custom inspection systems. This paper will review the recent advances in noncontacting sensor development. Machine vision and fiber optics sensor systems are finding a wide variety of industrial inspection applications. This paper will provide detailed examples of several state-of-the-art applications for these noncontacting sensors.

High-speed potato grading and quality inspection based on a color vision system

NASA Astrophysics Data System (ADS)

Noordam, Jacco C.; Otten, Gerwoud W.; Timmermans, Toine J. M.; van Zwol, Bauke H.

2000-03-01

A high-speed machine vision system for the quality inspection and grading of potatoes has been developed. The vision system grades potatoes on size, shape and external defects such as greening, mechanical damages, rhizoctonia, silver scab, common scab, cracks and growth cracks. A 3-CCD line-scan camera inspects the potatoes in flight as they pass under the camera. The use of mirrors to obtain a 360-degree view of the potato and the lack of product holders guarantee a full view of the potato. To achieve the required capacity of 12 tons/hour, 11 SHARC Digital Signal Processors perform the image processing and classification tasks. The total capacity of the system is about 50 potatoes/sec. The color segmentation procedure uses Linear Discriminant Analysis (LDA) in combination with a Mahalanobis distance classifier to classify the pixels. The procedure for the detection of misshapen potatoes uses a Fourier based shape classification technique. Features such as area, eccentricity and central moments are used to discriminate between similar colored defects. Experiments with red and yellow skin-colored potatoes have shown that the system is robust and consistent in its classification.

INFIBRA: machine vision inspection of acrylic fiber production

NASA Astrophysics Data System (ADS)

Davies, Roger; Correia, Bento A. B.; Contreiras, Jose; Carvalho, Fernando D.

1998-10-01

This paper describes the implementation of INFIBRA, a machine vision system for the inspection of acrylic fiber production lines. The system was developed by INETI under a contract from Fisipe, Fibras Sinteticas de Portugal, S.A. At Fisipe there are ten production lines in continuous operation, each approximately 40 m in length. A team of operators used to perform periodic manual visual inspection of each line in conditions of high ambient temperature and humidity. It is not surprising that failures in the manual inspection process occurred with some frequency, with consequences that ranged from reduced fiber quality to production stoppages. The INFIBRA system architecture is a specialization of a generic, modular machine vision architecture based on a network of Personal Computers (PCs), each equipped with a low cost frame grabber. Each production line has a dedicated PC that performs automatic inspection, using specially designed metrology algorithms, via four video cameras located at key positions on the line. The cameras are mounted inside custom-built, hermetically sealed water-cooled housings to protect them from the unfriendly environment. The ten PCs, one for each production line, communicate with a central PC via a standard Ethernet connection. The operator controls all aspects of the inspection process, from configuration through to handling alarms, via a simple graphical interface on the central PC. At any time the operator can also view on the central PC's screen the live image from any one of the 40 cameras employed by the system.

Process Approach to Determining Quality Inspection Deployment

DTIC Science & Technology

2015-06-08

27 B.1 The Deming Rule...k1/k2? [5] At this stage it is assumed that the manufacturing process is capable and that inspection is effective. The Deming rule is explained in...justify reducing inspectors. (See Appendix B for Deming rule discussion.) Three quantities must be determined: p, the probability of a nonconformity

9 CFR 355.41 - Antemortem and postmortem inspection for mules.

Code of Federal Regulations, 2014 CFR

2014-01-01

... for mules. 355.41 Section 355.41 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE...; INSPECTION, CERTIFICATION, AND IDENTIFICATION AS TO CLASS, QUALITY, QUANTITY, AND CONDITION Mule Meat and Animal Food, Mule Meat By-Product § 355.41 Antemortem and postmortem inspection for mules. (a)(1) An...

9 CFR 355.41 - Antemortem and postmortem inspection for mules.

Code of Federal Regulations, 2013 CFR

2013-01-01

... for mules. 355.41 Section 355.41 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE...; INSPECTION, CERTIFICATION, AND IDENTIFICATION AS TO CLASS, QUALITY, QUANTITY, AND CONDITION Mule Meat and Animal Food, Mule Meat By-Product § 355.41 Antemortem and postmortem inspection for mules. (a)(1) An...

9 CFR 355.41 - Antemortem and postmortem inspection for mules.

Code of Federal Regulations, 2011 CFR

2011-01-01

... for mules. 355.41 Section 355.41 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE...; INSPECTION, CERTIFICATION, AND IDENTIFICATION AS TO CLASS, QUALITY, QUANTITY, AND CONDITION Mule Meat and Animal Food, Mule Meat By-Product § 355.41 Antemortem and postmortem inspection for mules. (a)(1) An...

9 CFR 355.41 - Antemortem and postmortem inspection for mules.

Code of Federal Regulations, 2012 CFR

2012-01-01

... for mules. 355.41 Section 355.41 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE...; INSPECTION, CERTIFICATION, AND IDENTIFICATION AS TO CLASS, QUALITY, QUANTITY, AND CONDITION Mule Meat and Animal Food, Mule Meat By-Product § 355.41 Antemortem and postmortem inspection for mules. (a)(1) An...

Quantitative approach for optimizing e-beam condition of photoresist inspection and measurement

NASA Astrophysics Data System (ADS)

Lin, Chia-Jen; Teng, Chia-Hao; Cheng, Po-Chung; Sato, Yoshishige; Huang, Shang-Chieh; Chen, Chu-En; Maruyama, Kotaro; Yamazaki, Yuichiro

2018-03-01

Severe process margin in advanced technology node of semiconductor device is controlled by e-beam metrology system and e-beam inspection system with scanning electron microscopy (SEM) image. By using SEM, larger area image with higher image quality is required to collect massive amount of data for metrology and to detect defect in a large area for inspection. Although photoresist is the one of the critical process in semiconductor device manufacturing, observing photoresist pattern by SEM image is crucial and troublesome especially in the case of large image. The charging effect by e-beam irradiation on photoresist pattern causes deterioration of image quality, and it affect CD variation on metrology system and causes difficulties to continue defect inspection in a long time for a large area. In this study, we established a quantitative approach for optimizing e-beam condition with "Die to Database" algorithm of NGR3500 on photoresist pattern to minimize charging effect. And we enhanced the performance of measurement and inspection on photoresist pattern by using optimized e-beam condition. NGR3500 is the geometry verification system based on "Die to Database" algorithm which compares SEM image with design data [1]. By comparing SEM image and design data, key performance indicator (KPI) of SEM image such as "Sharpness", "S/N", "Gray level variation in FOV", "Image shift" can be retrieved. These KPIs were analyzed with different e-beam conditions which consist of "Landing Energy", "Probe Current", "Scanning Speed" and "Scanning Method", and the best e-beam condition could be achieved with maximum image quality, maximum scanning speed and minimum image shift. On this quantitative approach of optimizing e-beam condition, we could observe dependency of SEM condition on photoresist charging. By using optimized e-beam condition, measurement could be continued on photoresist pattern over 24 hours stably. KPIs of SEM image proved image quality during measurement and

Nondestructive web thickness measurement of micro-drills with an integrated laser inspection system

NASA Astrophysics Data System (ADS)

Chuang, Shui-Fa; Chen, Yen-Chung; Chang, Wen-Tung; Lin, Ching-Chih; Tarng, Yeong-Shin

2010-09-01

Nowadays, the electric and semiconductor industries use numerous micro-drills to machine micro-holes in printed circuit boards. The measurement of web thickness of micro-drills, a key parameter of micro-drill geometry influencing drill rigidity and chip-removal ability, is quite important to ensure quality control. Traditionally, inefficiently destructive measuring method is adopted by inspectors. To improve quality and efficiency of the web thickness measuring tasks, a nondestructive measuring method is required. In this paper, based on the laser micro-gauge (LMG) and laser confocal displacement meter (LCDM) techniques, a nondestructive measuring principle of web thickness of micro-drills is introduced. An integrated laser inspection system, mainly consisting of a LMG, a LCDM and a two-axis-driven micro-drill fixture device, was developed. Experiments meant to inspect web thickness of micro-drill samples with a nominal diameter of 0.25 mm were conducted to test the feasibility of the developed laser inspection system. The experimental results showed that the web thickness measurement could achieve an estimated repeatability of ± 1.6 μm and a worst repeatability of ± 7.5 μm. The developed laser inspection system, combined with the nondestructive measuring principle, was able to undertake the web thickness measuring tasks for certain micro-drills.

46 CFR 160.060-7 - Inspections and tests-standard and nonstandard vests. 1

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Inspections and tests-standard and nonstandard vests. 1... and nonstandard vests. 1 1 The manufacturer of a personal flotation device must meet 33 CFR 181.701... shall— (1) Maintain quality control of the materials used, the manufacturing methods, and the finished...

46 CFR 160.060-7 - Inspections and tests-standard and nonstandard vests. 1

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Inspections and tests-standard and nonstandard vests. 1... and nonstandard vests. 1 1 The manufacturer of a personal flotation device must meet 33 CFR 181.701... shall— (1) Maintain quality control of the materials used, the manufacturing methods, and the finished...

Level of Service Program for INDOT Operations : APPENDIX A State Inspection Programs

DOT National Transportation Integrated Search

2012-01-01

INDOT has used an inspection program named Maintenance Quality Survey (MQS) to perform a statewide inspection of their roadway assets, rightofway to rightofway. This inspection requires two twoperson teams approximately 18 months to...

Level of Service Program for INDOT Operations : APPENDIX C Los Inspection Manual

DOT National Transportation Integrated Search

2012-01-01

INDOT has used an inspection program named Maintenance Quality Survey (MQS) to perform a statewide inspection of their roadway assets, rightofway to rightofway. This inspection requires two twoperson teams approximately 18 months to...

High-performance camera module for fast quality inspection in industrial printing applications

NASA Astrophysics Data System (ADS)

Fürtler, Johannes; Bodenstorfer, Ernst; Mayer, Konrad J.; Brodersen, Jörg; Heiss, Dorothea; Penz, Harald; Eckel, Christian; Gravogl, Klaus; Nachtnebel, Herbert

2007-02-01

Today, printing products which must meet highest quality standards, e.g., banknotes, stamps, or vouchers, are automatically checked by optical inspection systems. Typically, the examination of fine details of the print or security features demands images taken from various perspectives, with different spectral sensitivity (visible, infrared, ultraviolet), and with high resolution. Consequently, the inspection system is equipped with several cameras and has to cope with an enormous data rate to be processed in real-time. Hence, it is desirable to move image processing tasks into the camera to reduce the amount of data which has to be transferred to the (central) image processing system. The idea is to transfer relevant information only, i.e., features of the image instead of the raw image data from the sensor. These features are then further processed. In this paper a color line-scan camera for line rates up to 100 kHz is presented. The camera is based on a commercial CMOS (complementary metal oxide semiconductor) area image sensor and a field programmable gate array (FPGA). It implements extraction of image features which are well suited to detect print flaws like blotches of ink, color smears, splashes, spots and scratches. The camera design and several image processing methods implemented on the FPGA are described, including flat field correction, compensation of geometric distortions, color transformation, as well as decimation and neighborhood operations.

Additive Manufacturing Infrared Inspection

NASA Technical Reports Server (NTRS)

Gaddy, Darrell

2014-01-01

Additive manufacturing is a rapid prototyping technology that allows parts to be built in a series of thin layers from plastic, ceramics, and metallics. Metallic additive manufacturing is an emerging form of rapid prototyping that allows complex structures to be built using various metallic powders. Significant time and cost savings have also been observed using the metallic additive manufacturing compared with traditional techniques. Development of the metallic additive manufacturing technology has advanced significantly over the last decade, although many of the techniques to inspect parts made from these processes have not advanced significantly or have limitations. Several external geometry inspection techniques exist such as Coordinate Measurement Machines (CMM), Laser Scanners, Structured Light Scanning Systems, or even traditional calipers and gages. All of the aforementioned techniques are limited to external geometry and contours or must use a contact probe to inspect limited internal dimensions. This presentation will document the development of a process for real-time dimensional inspection technique and digital quality record of the additive manufacturing process using Infrared camera imaging and processing techniques.

School Nurse Inspections Improve Handwashing Supplies

PubMed Central

Ramos, Mary M.; Schrader, Ronald; Trujillo, Rebecca; Blea, Mary; Greenberg, Cynthia

2013-01-01

BACKGROUND Handwashing in the school setting is important for infectious disease control, yet maintaining adequate handwashing supplies is often made difficult by lack of funds, limited staff time, and student vandalism. This study measured the availability of handwashing supplies for students in New Mexico public schools and determined the impact of scheduled school nurse inspections on the availability of handwashing supplies. METHODS Participating school districts in New Mexico were matched by size and randomized into intervention and control groups. Baseline inspections were conducted in November 2008 followed by 2 subsequent bimonthly inspections. For each student bathroom, the presence or absence of soap and either paper towels or hand dryers was indicated on an inspection checklist. The intervention group reported findings to the New Mexico Department of Health (NMDOH) and to school administrative and custodial staff requesting that any identified problems be addressed. The control group reported inspection findings to the NMDOH only. Descriptive analyses were conducted to determine the proportion of bathrooms with soap and either paper towels or hand dryers. Comparisons were made between the intervention schools and the control schools at baseline and during the intervention period. RESULTS The intervention group had significantly higher probability of bathrooms being supplied with soap (p < .05) and paper towels/hand dryers (p < .02) during the intervention period. CONCLUSIONS Regularly scheduled school nurse inspections of hand hygiene supplies, with reporting to appropriate school officials, can improve the availability of handwashing supplies for students. PMID:21592131

Report: Examination of Pilot Peer Review Process for Inspectors General That Follow “Blue Book” Quality Standards for Inspection and Evaluation

EPA Pesticide Factsheets

Report #16-N-0317, Sept 21, 2016. A peer review process that measures adherence to all the quality standards for federal Inspector General Inspection and Evaluation offices provides assurance that participating offices are being adequately evaluated.

Methodology For Reduction Of Sampling On The Visual Inspection Of Developed And Etched Wafers

NASA Astrophysics Data System (ADS)

van de Ven, Jamie S.; Khorasani, Fred

1989-07-01

There is a lot of inspection in the manufacturing of semiconductor devices. Generally, the more important a manufacturing step, the higher is the level of inspection. In some cases 100% of the wafers are inspected after certain steps. Inspection is a non-value added and expensive activity. It requires an army of "inspectors," often times expensive equipment and becomes a "bottle neck" when the level of inspection is high. Although inspection helps identify quality problems, it hurts productivity. The new management, quality and productivity philosophies recommend against over inspection. [Point #3 in Dr. Deming's 14 Points for Management (1)] 100% inspection is quite unnecessary . Often the nature of a process allows us to reduce inspection drastically and still maintain a high level of confidence in quality. In section 2, we discuss such situations and show that some elementary probability theory allows us to determine sample sizes and measure the chances of catching a bad "lot" and accepting a good lot. In section 3, we provide an example and application of the theory, and make a few comments on money and time saved because of this work. Finally, in section 4, we draw some conclusions about the new quality and productivity philosophies and how applied statisticians and engineers should study every situation individually and avoid blindly using methods and tables given in books.

Thermographic Inspections And The Residential Conservation Service Program (RCS)

NASA Astrophysics Data System (ADS)

Ward, Ronald J.

1983-03-01

Rhode Islanders Saving Energy (RISE) is a non-profit corporation founded in 1977 to provide Rhode Island residents with a variety of energy conservation services. Since January of 1981, it has been performing energy audits in compliance with the Department of Energy's (DOE) Residential Conservation Service Program (RCS). One aspect of the RCS program is the performance of inspections on energy conservation activities completed according to RCS installation guidelines. This paper will describe both the use and results of thermographic inspections within the RISE program. The primary objective of these inspections has been to assure the quality of the building envelope after completion of retrofit measures. Thermal anamolies have been detected that vary in size, location and probable cause. Approximately 37% of all jobs performed through RISE in conjunction with the RCS program have required remedial work as a result of problems that were identi-fied during the thermographic inspection. This percentage was much higher when infra-red inspections were conducted on "Non-RCS" retrofits. Statistics will be presented that provide an interesting insight on the quality of retrofit work when performed in associa-tion with a constant inspection process.

Robotic NDE inspection of advanced solid rocket motor casings

NASA Technical Reports Server (NTRS)

Mcneelege, Glenn E.; Sarantos, Chris

1994-01-01

The Advanced Solid Rocket Motor program determined the need to inspect ASRM forgings and segments for potentially catastrophic defects. To minimize costs, an automated eddy current inspection system was designed and manufactured for inspection of ASRM forgings in the initial phases of production. This system utilizes custom manipulators and motion control algorithms and integrated six channel eddy current data acquisition and analysis hardware and software. Total system integration is through a personal computer based workcell controller. Segment inspection demands the use of a gantry robot for the EMAT/ET inspection system. The EMAT/ET system utilized similar mechanical compliancy and software logic to accommodate complex part geometries. EMAT provides volumetric inspection capability while eddy current is limited to surface and near surface inspection. Each aspect of the systems are applicable to other industries, such as, inspection of pressure vessels, weld inspection, and traditional ultrasonic inspection applications.

46 CFR 160.052-7 - Inspections and tests-standard and nonstandard vests. 1

Code of Federal Regulations, 2014 CFR

2014-10-01

... Buoyant Vest, Unicellular Plastic Foam, Adult and Child § 160.052-7 Inspections and tests—standard and...) Maintain quality control of the materials used, the manufacturing methods and workmanship, and the finished... scale in such a manner that the basket can be weighed while it is completely under water. In order to...

46 CFR 160.052-7 - Inspections and tests-standard and nonstandard vests. 1

Code of Federal Regulations, 2012 CFR

2012-10-01

... Buoyant Vest, Unicellular Plastic Foam, Adult and Child § 160.052-7 Inspections and tests—standard and...) Maintain quality control of the materials used, the manufacturing methods and workmanship, and the finished... scale in such a manner that the basket can be weighed while it is completely under water. In order to...

46 CFR 160.052-7 - Inspections and tests-standard and nonstandard vests. 1

Code of Federal Regulations, 2013 CFR

2013-10-01

... Buoyant Vest, Unicellular Plastic Foam, Adult and Child § 160.052-7 Inspections and tests—standard and...) Maintain quality control of the materials used, the manufacturing methods and workmanship, and the finished... scale in such a manner that the basket can be weighed while it is completely under water. In order to...

Remote surface inspection system

NASA Astrophysics Data System (ADS)

Hayati, S.; Balaram, J.; Seraji, H.; Kim, W. S.; Tso, K.; Prasad, V.

1993-02-01

This paper reports on an on-going research and development effort in remote surface inspection of space platforms such as the Space Station Freedom (SSF). It describes the space environment and identifies the types of damage for which to search. This paper provides an overview of the Remote Surface Inspection System that was developed to conduct proof-of-concept demonstrations and to perform experiments in a laboratory environment. Specifically, the paper describes three technology areas: (1) manipulator control for sensor placement; (2) automated non-contact inspection to detect and classify flaws; and (3) an operator interface to command the system interactively and receive raw or processed sensor data. Initial findings for the automated and human visual inspection tests are reported.

Remote surface inspection system

NASA Technical Reports Server (NTRS)

Hayati, S.; Balaram, J.; Seraji, H.; Kim, W. S.; Tso, K.; Prasad, V.

1993-01-01

This paper reports on an on-going research and development effort in remote surface inspection of space platforms such as the Space Station Freedom (SSF). It describes the space environment and identifies the types of damage for which to search. This paper provides an overview of the Remote Surface Inspection System that was developed to conduct proof-of-concept demonstrations and to perform experiments in a laboratory environment. Specifically, the paper describes three technology areas: (1) manipulator control for sensor placement; (2) automated non-contact inspection to detect and classify flaws; and (3) an operator interface to command the system interactively and receive raw or processed sensor data. Initial findings for the automated and human visual inspection tests are reported.

Implementation of basic quality control tests for malaria medicines in Amazon Basin countries: results for the 2005–2010 period

PubMed Central

2012-01-01

Background Ensuring the quality of malaria medicines is crucial in working toward malaria control and eventual elimination. Unlike other validated tests that can assess all critical quality attributes, which is the standard for determining the quality of medicines, basic tests are significantly less expensive, faster, and require less skilled labour; yet, these tests provide reproducible data and information on several critical quality attributes, such as identity, purity, content, and disintegration. Visual and physical inspection also provides valuable information about the manufacturing and the labelling of medicines, and in many cases this inspection is sufficient to detect counterfeit medicines. The Promoting the Quality of Medicines (PQM) programme has provided technical assistance to Amazon Malaria Initiative (AMI) countries to implement the use of basic tests as a key screening mechanism to assess the quality of malaria medicines available to patients in decentralized regions. Methods Trained personnel from the National Malaria Control Programmes (NMCPs), often in collaboration with country’s Official Medicine Control Laboratory (OMCL), developed country- specific protocols that encompassed sampling methods, sample analysis, and data reporting. Sampling sites were selected based on malaria burden, accessibility, and geographical location. Convenience sampling was performed and countries were recommended to store the sampled medicines under conditions that did not compromise their quality. Basic analytical tests, such as disintegration and thin layer chromatography (TLC), were performed utilizing a portable mini-laboratory. Results Results were originally presented at regional meetings in a non-standardized format that lacked relevant medicines information. However, since 2008 information has been submitted utilizing a template specifically developed by PQM for that purpose. From 2005 to 2010, the quality of 1,663 malaria medicines from seven AMI countries

[PICS: pharmaceutical inspection cooperation scheme].

PubMed

Morénas, J

2009-01-01

The pharmaceutical inspection cooperation scheme (PICS) is a structure containing 34 participating authorities located worldwide (October 2008). It has been created in 1995 on the basis of the pharmaceutical inspection convention (PIC) settled by the European free trade association (EFTA) in1970. This scheme has different goals as to be an international recognised body in the field of good manufacturing practices (GMP), for training inspectors (by the way of an annual seminar and experts circles related notably to active pharmaceutical ingredients [API], quality risk management, computerized systems, useful for the writing of inspection's aide-memoires). PICS is also leading to high standards for GMP inspectorates (through regular crossed audits) and being a room for exchanges on technical matters between inspectors but also between inspectors and pharmaceutical industry.

New design environment for defect detection in web inspection systems

NASA Astrophysics Data System (ADS)

Hajimowlana, S. Hossain; Muscedere, Roberto; Jullien, Graham A.; Roberts, James W.

1997-09-01

One of the aims of industrial machine vision is to develop computer and electronic systems destined to replace human vision in the process of quality control of industrial production. In this paper we discuss the development of a new design environment developed for real-time defect detection using reconfigurable FPGA and DSP processor mounted inside a DALSA programmable CCD camera. The FPGA is directly connected to the video data-stream and outputs data to a low bandwidth output bus. The system is targeted for web inspection but has the potential for broader application areas. We describe and show test results of the prototype system board, mounted inside a DALSA camera and discuss some of the algorithms currently simulated and implemented for web inspection applications.

Reaching a Conclusion--Procedures and Processes of Judgement Formation in School Inspection Teams

ERIC Educational Resources Information Center

Dedering, Kathrin; Sowada, Moritz G.

2017-01-01

School inspections have become an important instrument of quality assurance and quality development in many European countries. So far, the focus of empirical research on school inspections has been on the acceptance of the procedure among the school-internal actors, its influence for internal quality development and its effects on student…

10 CFR 1016.43 - Inspections.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Inspections. 1016.43 Section 1016.43 Energy DEPARTMENT OF ENERGY (GENERAL PROVISIONS) SAFEGUARDING OF RESTRICTED DATA Control of Information § 1016.43 Inspections.... 10, 1983, as amended at 71 FR 68735, Nov. 28, 2006] ...

10 CFR 1016.43 - Inspections.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Inspections. 1016.43 Section 1016.43 Energy DEPARTMENT OF ENERGY (GENERAL PROVISIONS) SAFEGUARDING OF RESTRICTED DATA Control of Information § 1016.43 Inspections.... 10, 1983, as amended at 71 FR 68735, Nov. 28, 2006] ...

Inspection Tools

NASA Astrophysics Data System (ADS)

1989-01-01

A "NASA Tech Briefs" article describing an inspection tool and technique known as Optically Stimulated Electron Emission (OSEE) led to the formation of Photo Acoustic Technology, Inc. (PAT). PAT produces sensors and scanning systems which assure surface cleanliness prior to bonding, coating, painting, etc. The company's OP1000 series realtime pre-processing detection capability assures 100 percent surface quality testing. The technique involves brief exposure of the inspection surface to ultraviolet radiation. The energy interacts with the surface layer, causing free electrons to be emitted from the surface to be picked up by the detector. When contamination is present, it interferes with the electron flow in proportion to the thickness of the contaminant layer enabling measurement by system signal output. OP1000 systems operate in conventional atmospheres on all types of material and detect both organic and inorganic contamination.

Development of an Inverse Algorithm for Resonance Inspection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lai, Canhai; Xu, Wei; Sun, Xin

2012-10-01

Resonance inspection (RI), which employs the natural frequency spectra shift between the good and the anomalous part populations to detect defects, is a non-destructive evaluation (NDE) technique with many advantages such as low inspection cost, high testing speed, and broad applicability to structures with complex geometry compared to other contemporary NDE methods. It has already been widely used in the automobile industry for quality inspections of safety critical parts. Unlike some conventionally used NDE methods, the current RI technology is unable to provide details, i.e. location, dimension, or types, of the flaws for the discrepant parts. Such limitation severely hindersmore » its wide spread applications and further development. In this study, an inverse RI algorithm based on maximum correlation function is proposed to quantify the location and size of flaws for a discrepant part. A dog-bone shaped stainless steel sample with and without controlled flaws are used for algorithm development and validation. The results show that multiple flaws can be accurately pinpointed back using the algorithms developed, and the prediction accuracy decreases with increasing flaw numbers and decreasing distance between flaws.« less

9 CFR 381.223 - Control and disposition of nonfederally inspected poultry products in States designated under...

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY... Clearly Endanger the Public Health; Disposition of Poultry Products Therein § 381.223 Control and...

[Inspection by infection control team of the University Hospital, Faculty of Dentistry, Tokyo Medical and Dental University].

PubMed

Sunakawa, Mitsuhiro; Matsumoto, Hiroyuki; Harasawa, Hideki; Tsukikawa, Wakana; Takagi, Yuzo; Suda, Hideaki

2006-06-01

Factors affecting infection are the existence of infectious microorganisms, sensitivity of hosts, number of microorganisms, and infectious routes. Efforts to prevent infection focus on not allowing these factors to reach the threshold level. Inspection by an infection control team (ICT) of a hospital is one countermeasure for preventing nosocomial infection. We summarize here the problems for complete prevention of nosocomial infection based on the results of inspection by our ICT, so that staff working in the hospital can recognize the importance of preventing nosocomial infection. The following were commonly observed problems in our clinics found by the ICT : (1) incomplete practice of standard precautions and/or isolation precautions, (2) noncompliance with guidelines for the prevention of cross-infection, and (3) inappropriate management of medical rejectamenta. Infection control can be accomplished by strictly observing the standard precautions and isolation precautions. The ICT inspection round in the hospital could be an effective metaff working in the hod to clarify and overcome the problems involved in infection.

Automated X-ray quality control of catalytic converters

NASA Astrophysics Data System (ADS)

Shashishekhar, N.; Veselitza, D.

2017-02-01

Catalytic converters are devices attached to the exhaust system of automobile or other engines to eliminate or substantially reduce polluting emissions. They consist of coated substrates enclosed in a stainless steel housing. The substrate is typically made of ceramic honeycombs; however stainless steel foil honeycombs are also used. The coating is usually a slurry of alumina, silica, rare earth oxides and platinum group metals. The slurry also known as the wash coat is applied to the substrate in two doses, one on each end of the substrate; in some cases multiple layers of coating are applied. X-ray imaging is used to inspect the applied coating depth on a substrate to confirm compliance with quality requirements. Automated image analysis techniques are employed to measure the coating depth from the X-ray image. Coating depth is assessed by analysis of attenuation line profiles in the image. Edge detection algorithms with noise reduction and outlier rejection are used to calculate the coating depth at a specified point along an attenuation line profile. Quality control of the product is accomplished using several attenuation line profile regions for coating depth measurements, with individual pass or fail criteria specified for each region.

Submillimeter bolt location in car bodywork for production line quality inspection

NASA Astrophysics Data System (ADS)

Altamirano-Robles, Leopoldo; Arias-Estrada, Miguel; Alviso-Quibrera, Samuel; Lopez-Lopez, Aurelio

2000-03-01

In the automotive industry, a vehicle begins with the construction of the vehicle floor. Later on, several robots weld a series of bolts to this floor which are used to fix other parts. Due to several problems, like welding tools wearing, robot miscalibration or momentary low power supply, among others, some bolts are incorrectly positioned or are not present at all, bringing problems and delays in the next work cells. Therefore, it is of importance to verify the quality of welded parts before the following assembly steps. A computer vision system is proposed in order to locate autonomously the presence and quality of the bolts. The system should carry on the inspection in real time at the car assembly line under the following conditions: without touching the bodywork, with a precision in the submillimeter range and in few seconds. In this paper we present a basic computer vision system for bolt location in the submillimeter range. We analyze three arrangements of the system components (camera and illumination sources) that produce different results in the localization. Results are presented and compared for the three approaches obtained under laboratory conditions. The algorithms were tested in the assembling line. Variations up to one millimeter in the welded position of the bolts were observed.

Improving software quality - The use of formal inspections at the Jet Propulsion Laboratory

NASA Technical Reports Server (NTRS)

Bush, Marilyn

1990-01-01

The introduction of software formal inspections (Fagan Inspections) at JPL for finding and fixing defects early in the software development life cycle are reviewed. It is estimated that, by the year 2000, some software efforts will rise to as much as 80 percent of the total. Software problems are especially important at NASA as critical flight software must be error-free. It is shown that formal inspections are particularly effective at finding and removing defects having to do with clarity, correctness, consistency, and completeness. A very significant discovery was that code audits were not as effective at finding defects as code inspections.

A highly redundant robot system for inspection

NASA Technical Reports Server (NTRS)

Lee, Thomas S.; Ohms, Tim; Hayati, Samad

1994-01-01

The work on the serpentine inspection system at JPL is described. The configuration of the inspection system consists of 20 degrees of freedom in total. In particular, the design and development of the serpentine micromanipulator end-effector tool which has 12 degrees of freedom is described. The inspection system is used for application in JPL's Remote Surface Inspection project and as a research tool in redundant manipulator control.

Principles and Practices for Quality Assurance and Quality Control

USGS Publications Warehouse

Jones, Berwyn E.

1999-01-01

Quality assurance and quality control are vital parts of highway runoff water-quality monitoring projects. To be effective, project quality assurance must address all aspects of the project, including project management responsibilities and resources, data quality objectives, sampling and analysis plans, data-collection protocols, data quality-control plans, data-assessment procedures and requirements, and project outputs. Quality control ensures that the data quality objectives are achieved as planned. The historical development and current state of the art of quality assurance and quality control concepts described in this report can be applied to evaluation of data from prior projects.

Serpentine Robots for Inspection Tasks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choset, Howie

2003-09-11

Serpentine robots are snake like devices that can use their internal degrees of freedom to thread through tightly packed volumes accessing locations that people or conventional machinery cannot. These devices are ideally suited for minimally invasive inspection tasks where the surrounding areas do not have to be disturbed. Applications for these devices are therefore inspection of underground tanks and other storage facilities for classification purposes. This work deals with the design, construction, and control of a serpentine robot. The challenges lie in developing a device that can lift itself in three dimensions, which is necessary for the inspection tasks. Themore » other challenge in control deals with coordinating all of the internal degrees of freedom to exact purposeful motion.« less

Appendix G - Spill Prevention, Control, and Countermeasure (SPCC) Inspection Checklists - Tier I Qualified Facility Checklist

EPA Pesticide Factsheets

For Tier I Qualified Facilities - This checklist assists EPA inspectors in conducting a thorough and nationally consistent inspection of a facility’s compliance with the Spill Prevention, Control, and Countermeasure (SPCC) rule at 40 CFR Part 112.

Getting Ready for Inspection of Investigational Site at Short Notice

PubMed Central

Talele, Rajendra

2010-01-01

India is becoming an attractive destination for drug development and clinical research. This is evidenced by the three fold increment in clinical trial applications in last four years to the office of Drugs Controller General of India (DCGI). This upward trend is collaborative efforts of all stake holders and the quality of Indian data. Therefore to sustain this trend, it is important that stake holders such as Regulators, Sponsor, CRO, Monitor, Investigators and trial subjects required maintaining high standards of data and conduct of clinical trials. Indian regulations and the role of DCGI in quality check for Indian clinical trials is always a topic of discussion in various forums. A recent move by DCGI for conducting random inspections of investigational sites and companies at short notice, checking their compliance in accordance with the guidelines, and taking action against non-complier is welcomed. This will certainly increase over quality of the clinical trials. Quality of clinical trial conduct is measured on essential documents for their appropriateness and its correctness. It is observed that the stakeholders engaged in multitasking often overlook the requirements or appropriateness of the document due to their focused approach on a specific activity which is on priority. This can lead to serious quality problem and issues. Understanding of the process and documents reviewed by auditor is important to maintain such high quality. The proper planning and time management working on essential documents can minimize the quality issues, and we can be always ready for any type of inspection, announced or unannounced, or “short notice”. PMID:21829785

Pipeline inspection using an autonomous underwater vehicle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Egeskov, P.; Bech, M.; Bowley, R.

1995-12-31

Pipeline inspection can be carried out by means of small Autonomous Underwater Vehicles (AUVs), operating either with a control link to a surface vessel, or totally independently. The AUV offers an attractive alternative to conventional inspection methods where Remotely Operated Vehicles (ROVs) or paravanes are used. A flatfish type AUV ``MARTIN`` (Marine Tool for Inspection) has been developed for this purpose. The paper describes the proposed types of inspection jobs to be carried out by ``MARTIN``. The design and construction of the vessel, its hydrodynamic properties, its propulsion and control systems are discussed. The pipeline tracking and survey systems, asmore » well as the launch and recovery systems are described.« less

[Accession to the PIC/S and pharmaceutical quality system in Japan].

PubMed

Katori, Noriko

2014-01-01

In March, 2012, Japan made the application for membership of the Pharmaceutical Inspection convention and Pharmaceutical Inspection Co-operation scheme (PIC/S) which is an international body of a GMP inspection. The globalization of pharmaceutical manufacturing and sales has been a driving force behind the decision to become a PIC/S member. For the application for membership, Japan's GMP inspectorate needs to fulfill PIC/S requirements, for example, the inspection organization has to have a quality system as a global standard. One of the other requirements is that the GMP inspectorate can access Official Medicines Control Laboratories (OMCL) having high analytical skills and also have a quality system based on ISO 17025. I would like to describe the process to make up a quality system in the National Institute of Health Sciences and also the circumstances around the PIC/S application in Japan.

Automatic optical inspection system design for golf ball

NASA Astrophysics Data System (ADS)

Wu, Hsien-Huang; Su, Jyun-Wei; Chen, Chih-Lin

2016-09-01

ith the growing popularity of golf sport all over the world, the quantities of relevant products are increasing year by year. To create innovation and improvement in quality while reducing production cost, automation of manufacturing become a necessary and important issue. This paper reflect the trend of this production automa- tion. It uses the AOI (Automated Optical Inspection) technology to develop a system which can automatically detect defects on the golf ball. The current manual quality-inspection is not only error-prone but also very man- power demanding. Taking into consideration the competition of this industry in the near future, the development of related AOI equipment must be conducted as soon as possible. Due to the strong reflective property of the ball surface, as well as its surface dimples and subtle flaws, it is very difficult to take good quality image for automatic inspection. Based on the surface properties and shape of the ball, lighting has been properly design for image-taking environment and structure. Area-scan cameras have been used to acquire images with good contrast between defects and background to assure the achievement of the goal of automatic defect detection on the golf ball. The result obtained is that more than 973 of the NG balls have be detected, and system maintains less than 103 false alarm rate. The balls which are determined by the system to be NG will be inspected by human eye again. Therefore, the manpower spent in the inspection has been reduced by 903.

Quality engineering as a profession.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolb, Rachel R.; Hoover, Marcey L.

Over the course of time, the profession of quality engineering has witnessed significant change, from its original emphasis on quality control and inspection to a more contemporary focus on upholding quality processes throughout the organization and its product realization activities. This paper describes the profession of quality engineering, exploring how todays quality engineers and quality professionals are certified individuals committed to upholding quality processes and principles while working with different dimensions of product development. It also discusses the future of the quality engineering profession and the future of the quality movement as a whole.

Principals' Reactions to Feedback Received by School Inspection: A Longitudinal Study

ERIC Educational Resources Information Center

Behnke, Kristin; Steins, Gisela

2017-01-01

This article presents the results of a follow-up study on the attitudes of German principals towards receiving feedback from school inspections. In a first study, we explored the attitudes of 50 principals towards feedback from school inspections [Quality Analysis (QA) in North Rhine-Westphalia] before school inspections took place at these…

Does Accountability Pressure through School Inspections Promote School Improvement?

ERIC Educational Resources Information Center

Altrichter, Herbert; Kemethofer, David

2015-01-01

"New" school inspections are essential parts of "evidence-based governance" concepts and have been implemented by many European countries as a major strategy to assure and improve the effectiveness and quality of their education systems. However, national inspection systems vary in their composition and in their contextual…

Rail inspection system based on iGPS

NASA Astrophysics Data System (ADS)

Fu, Xiaoyan; Wang, Mulan; Wen, Xiuping

2018-05-01

Track parameters include gauge, super elevation, cross level and so on, which could be calculated through the three-dimensional coordinates of the track. The rail inspection system based on iGPS (indoor/infrared GPS) was composed of base station, receiver, rail inspection frame, wireless communication unit, display and control unit and data processing unit. With the continuous movement of the inspection frame, the system could accurately inspect the coordinates of rail; realize the intelligent detection and precision measurement. According to principle of angle intersection measurement, the inspection model was structured, and detection process was given.

42 CFR 456.607 - Notification before inspection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.607 Notification before inspection. No facility may be...

Modelling and control for laser based welding processes: modern methods of process control to improve quality of laser-based joining methods

NASA Astrophysics Data System (ADS)

Zäh, Ralf-Kilian; Mosbach, Benedikt; Hollwich, Jan; Faupel, Benedikt

2017-02-01

To ensure the competitiveness of manufacturing companies it is indispensable to optimize their manufacturing processes. Slight variations of process parameters and machine settings have only marginally effects on the product quality. Therefore, the largest possible editing window is required. Such parameters are, for example, the movement of the laser beam across the component for the laser keyhole welding. That`s why it is necessary to keep the formation of welding seams within specified limits. Therefore, the quality of laser welding processes is ensured, by using post-process methods, like ultrasonic inspection, or special in-process methods. These in-process systems only achieve a simple evaluation which shows whether the weld seam is acceptable or not. Furthermore, in-process systems use no feedback for changing the control variables such as speed of the laser or adjustment of laser power. In this paper the research group presents current results of the research field of Online Monitoring, Online Controlling and Model predictive controlling in laser welding processes to increase the product quality. To record the characteristics of the welding process, tested online methods are used during the process. Based on the measurement data, a state space model is ascertained, which includes all the control variables of the system. Depending on simulation tools the model predictive controller (MPC) is designed for the model and integrated into an NI-Real-Time-System.

42 CFR 456.606 - Frequency of inspections.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.606 Frequency of inspections. The team and the agency...

48 CFR 246.370 - Material inspection and receiving report.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Material inspection and receiving report. 246.370 Section 246.370 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Clauses 246.370 Material inspection and receiving report. (a)...

48 CFR 246.370 - Material inspection and receiving report.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Material inspection and receiving report. 246.370 Section 246.370 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Clauses 246.370 Material inspection and receiving report. (a)...

Eddy-Current Inspection Of Tab Seals On Beverage Cans

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph

1994-01-01

Eddy-current inspection system monitors tab seals on beverage cans. Device inspects all cans at usual production rate of 1,500 to 2,000 cans per minute. Automated inspection of all units replaces visual inspection by microscope aided by mass spectrometry. System detects defects in real time. Sealed cans on conveyor pass near one of two coils in differential eddy-current probe. Other coil in differential eddy-current probe positioned near stationary reference can on which tab seal is known to be of acceptable quality. Signal of certain magnitude at output of probe indicates defective can, automatically ejected from conveyor.

42 CFR 456.611 - Reports on inspections.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.611 Reports on inspections. (a) The team must submit a...

Restaurant inspection frequency: The RestoFreq Study.

PubMed

Medu, Olanrewaju; Turner, Hollie; Cushon, Jennifer A; Melis, Deborah; Rea, Leslie; Abdellatif, Treena; Neudorf, Cory O; Schwandt, Michael

2017-03-01

Foodborne illness is an important contributor to morbidity and health system costs in Canada. Using number of critical hazards as a proxy for food safety, we sought to better understand how to improve food safety in restaurants. We compared the current standard of annual inspections to twice-yearly inspections among restaurants "at risk" for food safety infractions. These were restaurants that had three or more elevated-risk inspection ratings in the preceding 36 months. We conducted a two-arm randomized controlled trial between November 2012 and October 2014. The intervention was twice-yearly routine restaurant inspection compared to standard once-yearly routine inspection. Included were all restaurants within Saskatoon Health Region that were assessed as "at risk", with 73 restaurants in the intervention arm and 78 in the control arm. Independent sample t-tests were conducted between groups to compare: i) average number of critical hazards per inspection; and ii) proportion of inspections resulting in a rating indicating an elevated hazard. Over time we noted statistically significant improvements across both study arms, in number of both critical food safety hazards (decreased by 61%) and elevated-risk inspection ratings (decreased by 45%) (p < 0.0001). We observed no significant differences between the two groups pre- or post-intervention. Results suggest increasing the number of annual routine inspections in high-risk restaurants was not associated with a significant difference in measures of compliance with food safety regulations. Findings of this study do not provide evidence supporting increased frequency of restaurant inspection from annually to twice annually.

Inspection of care: Findings from an innovative demonstration

PubMed Central

Morris, John N.; Sherwood, Clarence C.; Dreyer, Paul

1989-01-01

In this article, information is presented concerning the efficacy of a sample-based approach to completing inspection of care reviews of Medicaid-supported nursing home residents. Massachusetts nursing homes were randomly assigned to full (the control group) or sample (the experimental group) review conditions. The primary research focus was to determine whether the proportion of facilities found to be deficient (based on quality of care and level of care criteria) in the experimental sample was comparable to the proportion in the control sample. The findings supported such a hypothesis: Deficient facilities appear to be equally identifiable using the random or full-sampling protocols, and the process can be completed with a considerable savings of surveyor time. PMID:10313458

Close-range photogrammetry for aircraft quality control

NASA Astrophysics Data System (ADS)

Schwartz, D. S.

Close range photogrammetry is applicable to quality assurance inspections, design data acquisition, and test management support tasks, yielding significant cost avoidance and increased productivity. An understanding of mensuration parameters and their related accuracies is fundamental to the successful application of industrial close range photogrammetry. Attention is presently given to these parameters and to the use of computer modelling as an aid to the photogrammetric entrepreneur in industry. Suggested improvements to cameras and film readers for industrial applications are discussed.

Software Design Improvements. Part 2; Software Quality and the Design and Inspection Process

NASA Technical Reports Server (NTRS)

Lalli, Vincent R.; Packard, Michael H.; Ziemianski, Tom

1997-01-01

The application of assurance engineering techniques improves the duration of failure-free performance of software. The totality of features and characteristics of a software product are what determine its ability to satisfy customer needs. Software in safety-critical systems is very important to NASA. We follow the System Safety Working Groups definition for system safety software as: 'The optimization of system safety in the design, development, use and maintenance of software and its integration with safety-critical systems in an operational environment. 'If it is not safe, say so' has become our motto. This paper goes over methods that have been used by NASA to make software design improvements by focusing on software quality and the design and inspection process.

Development of high sensitivity and high speed large size blank inspection system LBIS

NASA Astrophysics Data System (ADS)

Ohara, Shinobu; Yoshida, Akinori; Hirai, Mitsuo; Kato, Takenori; Moriizumi, Koichi; Kusunose, Haruhiko

2017-07-01

The production of high-resolution flat panel displays (FPDs) for mobile phones today requires the use of high-quality large-size photomasks (LSPMs). Organic light emitting diode (OLED) displays use several transistors on each pixel for precise current control and, as such, the mask patterns for OLED displays are denser and finer than the patterns for the previous generation displays throughout the entire mask surface. It is therefore strongly demanded that mask patterns be produced with high fidelity and free of defect. To enable the production of a high quality LSPM in a short lead time, the manufacturers need a high-sensitivity high-speed mask blank inspection system that meets the requirement of advanced LSPMs. Lasertec has developed a large-size blank inspection system called LBIS, which achieves high sensitivity based on a laser-scattering technique. LBIS employs a high power laser as its inspection light source. LBIS's delivery optics, including a scanner and F-Theta scan lens, focus the light from the source linearly on the surface of the blank. Its specially-designed optics collect the light scattered by particles and defects generated during the manufacturing process, such as scratches, on the surface and guide it to photo multiplier tubes (PMTs) with high efficiency. Multiple PMTs are used on LBIS for the stable detection of scattered light, which may be distributed at various angles due to irregular shapes of defects. LBIS captures 0.3mμ PSL at a detection rate of over 99.5% with uniform sensitivity. Its inspection time is 20 minutes for a G8 blank and 35 minutes for G10. The differential interference contrast (DIC) microscope on the inspection head of LBIS captures high-contrast review images after inspection. The images are classified automatically.

Research on Walking Wheel Slippage Control of Live Inspection Robot

NASA Astrophysics Data System (ADS)

Yan, Yu; Liu, Xiaqing; Guo, Hao; Li, Jinliang; Liu, Lanlan

2017-07-01

To solve the problem of walking wheel slippage of a live inspection robot during walking or climbing, this paper analyzes the climbing capacity of the robot with a statics method, designs a pressing wheel mechanism, and presents a method of indirectly identifying walking wheel slippage by reading speed of the pressing wheel due to the fact that the linear speed of the pressing wheel and the walking wheel at the contract point is the same; and finds that the slippage state can not be controlled through accurate mathematical models after identifying the slippage state, whereas slippage can be controlled with fuzzy control. The experiment results indicate that due to design of the pressing wheel mechanism, friction force of the walking wheel is increased, and the climbing capability of the robot is improved. Within the range of climbing capability of the robot, gradient is the key factor that has influence on slippage of robot, and slippage can be effectively eliminated through the fuzzy control method proposed in this paper.

9 CFR 304.2 - Information to be furnished; grant or refusal of inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... water quality standards. No grant of inspection can be issued after April 3, 1970 (the date of enactment of the Water Quality Improvement Act), unless such certification has been obtained, or is waived... inspection granted after April 3, 1970, for facilities existing or under construction on April 3, 1970...

In-vessel visible inspection system on KSTAR

NASA Astrophysics Data System (ADS)

Chung, Jinil; Seo, D. C.

2008-08-01

To monitor the global formation of the initial plasma and damage to the internal structures of the vacuum vessel, an in-vessel visible inspection system has been installed and operated on the Korean superconducting tokamak advanced research (KSTAR) device. It consists of four inspection illuminators and two visible/H-alpha TV cameras. Each illuminator uses four 150W metal-halide lamps with separate lamp controllers, and programmable progressive scan charge-coupled device cameras with 1004×1004 resolution at 48frames/s and a resolution of 640×480 at 210frames/s are used to capture images. In order to provide vessel inspection capability under any operation condition, the lamps and cameras are fully controlled from the main control room and protected by shutters from deposits during plasma operation. In this paper, we describe the design and operation results of the visible inspection system with the images of the KSTAR Ohmic discharges during the first plasma campaign.

Electro-Optical Inspection For Tolerance Control As An Integral Part Of A Flexible Machining Cell

NASA Astrophysics Data System (ADS)

Renaud, Blaise

1986-11-01

Institut CERAC has been involved in optical metrology and 3-dimensional surface control for the last couple of years. Among the industrial applications considered is the on-line shape evaluation of machined parts within the manufacturing cell. The specific objective is to measure the machining errors and to compare them with the tolerances set by designers. An electro-optical sensing technique has been developed which relies on a projection Moire contouring optical method. A prototype inspection system has been designed, making use of video detection and computer image processing. Moire interferograms are interpreted, and the metrological information automatically retrieved. A structured database can be generated for subsequent data analysis and for real-time closed-loop corrective actions. A real-time kernel embedded into a synchronisation network (Petri-net) for the control of concurrent processes in the Electra-Optical Inspection (E0I) station was realised and implemented in a MODULA-2 program DIN01. The prototype system for on-line automatic tolerance control taking place within a flexible machining cell is described in this paper, together with the fast-prototype synchronisation program.

40 CFR 264.1088 - Inspection and monitoring requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 26 2014-07-01 2014-07-01 false Inspection and monitoring requirements... FACILITIES Air Emission Standards for Tanks, Surface Impoundments, and Containers § 264.1088 Inspection and monitoring requirements. (a) The owner or operator shall inspect and monitor air emission control equipment...

40 CFR 264.1088 - Inspection and monitoring requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 27 2013-07-01 2013-07-01 false Inspection and monitoring requirements... FACILITIES Air Emission Standards for Tanks, Surface Impoundments, and Containers § 264.1088 Inspection and monitoring requirements. (a) The owner or operator shall inspect and monitor air emission control equipment...

40 CFR 264.1088 - Inspection and monitoring requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 27 2012-07-01 2012-07-01 false Inspection and monitoring requirements... FACILITIES Air Emission Standards for Tanks, Surface Impoundments, and Containers § 264.1088 Inspection and monitoring requirements. (a) The owner or operator shall inspect and monitor air emission control equipment...

40 CFR 264.1088 - Inspection and monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Inspection and monitoring requirements... FACILITIES Air Emission Standards for Tanks, Surface Impoundments, and Containers § 264.1088 Inspection and monitoring requirements. (a) The owner or operator shall inspect and monitor air emission control equipment...

40 CFR 264.1088 - Inspection and monitoring requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 26 2011-07-01 2011-07-01 false Inspection and monitoring requirements... FACILITIES Air Emission Standards for Tanks, Surface Impoundments, and Containers § 264.1088 Inspection and monitoring requirements. (a) The owner or operator shall inspect and monitor air emission control equipment...

QUALITY CONTROLS FOR PCR

EPA Science Inventory

The purpose of this presentation is to present an overview of the quality control (QC) sections of a draft EPA document entitled, "Quality Assurance/Quality Control Guidance for Laboratories Performing PCR Analyses on Environmental Samples." This document has been prepared by th...

Appendix G - Spill Prevention, Control, and Countermeasure (SPCC) Inspection Checklists - Offshore Oil Production, Drilling, and Workover

EPA Pesticide Factsheets

For offshore drilling/production facilities - This checklist assists EPA inspectors in conducting a thorough and consistent inspection of a facility’s compliance with the Spill Prevention, Control, and Countermeasure (SPCC) rule at 40 CFR part 112.

Automated surface inspection for steel products using computer vision approach.

PubMed

Xi, Jiaqi; Shentu, Lifeng; Hu, Jikang; Li, Mian

2017-01-10

Surface inspection is a critical step in ensuring the product quality in the steel-making industry. In order to relieve inspectors of laborious work and improve the consistency of inspection, much effort has been dedicated to the automated inspection using computer vision approaches over the past decades. However, due to non-uniform illumination conditions and similarity between the surface textures and defects, the present methods are usually applicable to very specific cases. In this paper a new framework for surface inspection has been proposed to overcome these limitations. By investigating the image formation process, a quantitative model characterizing the impact of illumination on the image quality is developed, based on which the non-uniform brightness in the image can be effectively removed. Then a simple classifier is designed to identify the defects among the surface textures. The significance of this approach lies in its robustness to illumination changes and wide applicability to different inspection scenarios. The proposed approach has been successfully applied to the real-time surface inspection of round billets in real manufacturing. Implemented on a conventional industrial PC, the algorithm can proceed at 12.5 frames per second with the successful detection rate being over 90% for turned and skinned billets.

Quality and Improvement in Scottish Education: Trends in Inspection Findings 2008-2011

ERIC Educational Resources Information Center

Education Scotland, 2012

2012-01-01

The findings of Education Scotland's sectoral programme of inspections, which sample the providers of education at every stage from the early years to adult learning, provide a key source of evidence on how effectively one of its core public services is performing. The last published summary of inspection findings was produced in 2009 when Her…

Determination of tire quality from nondestructive inspection : final report

DOT National Transportation Integrated Search

1979-11-01

The principal objective of the study was to assess the capability of an ultrasonic nondestructive inspection system to identify tire groups with a high propensity to failure among the groups selected for the Compliance Test under MVSS 109. A secondar...

Quality assurance and quality control for thermal/optical analysis of aerosol samples for organic and elemental carbon.

PubMed

Chow, Judith C; Watson, John G; Robles, Jerome; Wang, Xiaoliang; Chen, L-W Antony; Trimble, Dana L; Kohl, Steven D; Tropp, Richard J; Fung, Kochy K

2011-12-01

Accurate, precise, and valid organic and elemental carbon (OC and EC, respectively) measurements require more effort than the routine analysis of ambient aerosol and source samples. This paper documents the quality assurance (QA) and quality control (QC) procedures that should be implemented to ensure consistency of OC and EC measurements. Prior to field sampling, the appropriate filter substrate must be selected and tested for sampling effectiveness. Unexposed filters are pre-fired to remove contaminants and acceptance tested. After sampling, filters must be stored in the laboratory in clean, labeled containers under refrigeration (<4 °C) to minimize loss of semi-volatile OC. QA activities include participation in laboratory accreditation programs, external system audits, and interlaboratory comparisons. For thermal/optical carbon analyses, periodic QC tests include calibration of the flame ionization detector with different types of carbon standards, thermogram inspection, replicate analyses, quantification of trace oxygen concentrations (<100 ppmv) in the helium atmosphere, and calibration of the sample temperature sensor. These established QA/QC procedures are applicable to aerosol sampling and analysis for carbon and other chemical components.

Ultrasonic inspection and deployment apparatus

DOEpatents

Michaels, Jennifer E.; Michaels, Thomas E.; Mech, Jr., Stephen J.

1984-01-01

An ultrasonic inspection apparatus for the inspection of metal structures, especially installed pipes. The apparatus combines a specimen inspection element, an acoustical velocity sensing element, and a surface profiling element, all in one scanning head. A scanning head bellows contains a volume of oil above the pipe surface, serving as acoustical couplant between the scanning head and the pipe. The scanning head is mounted on a scanning truck which is mobile around a circular track surrounding the pipe. The scanning truck has sufficient motors, gears, and position encoders to allow the scanning head six degrees of motion freedom. A computer system continually monitors acoustical velocity, and uses that parameter to process surface profiling and inspection data. The profiling data is used to automatically control scanning head position and alignment and to define a coordinate system used to identify and interpret inspection data. The apparatus is suitable for highly automated, remote application in hostile environments, particularly high temperature and radiation areas.

The Effect of School Inspections on School Improvement

ERIC Educational Resources Information Center

Gaertner, Holger; Wurster, Sebastian; Pant, Hans Anand

2014-01-01

This study uses a school-level longitudinal control-group design to examine how teachers and principals of inspected versus uninspected schools perceive school improvement at their schools. During the phasing in of school inspections in the states of Berlin and Brandenburg (Germany), both inspected and uninspected schools were surveyed with…

Automating PACS quality control with the Vanderbilt image processing enterprise resource

NASA Astrophysics Data System (ADS)

Esparza, Michael L.; Welch, E. Brian; Landman, Bennett A.

2012-02-01

Precise image acquisition is an integral part of modern patient care and medical imaging research. Periodic quality control using standardized protocols and phantoms ensures that scanners are operating according to specifications, yet such procedures do not ensure that individual datasets are free from corruption; for example due to patient motion, transient interference, or physiological variability. If unacceptable artifacts are noticed during scanning, a technologist can repeat a procedure. Yet, substantial delays may be incurred if a problematic scan is not noticed until a radiologist reads the scans or an automated algorithm fails. Given scores of slices in typical three-dimensional scans and widevariety of potential use cases, a technologist cannot practically be expected inspect all images. In large-scale research, automated pipeline systems have had great success in achieving high throughput. However, clinical and institutional workflows are largely based on DICOM and PACS technologies; these systems are not readily compatible with research systems due to security and privacy restrictions. Hence, quantitative quality control has been relegated to individual investigators and too often neglected. Herein, we propose a scalable system, the Vanderbilt Image Processing Enterprise Resource (VIPER) to integrate modular quality control and image analysis routines with a standard PACS configuration. This server unifies image processing routines across an institutional level and provides a simple interface so that investigators can collaborate to deploy new analysis technologies. VIPER integrates with high performance computing environments has successfully analyzed all standard scans from our institutional research center over the course of the last 18 months.

[On-site quality control of acupuncture randomized controlled trial: design of content and checklist of quality control based on PICOST].

PubMed

Li, Hong-Jiao; He, Li-Yun; Liu, Zhi-Shun; Sun, Ya-Nan; Yan, Shi-Yan; Liu, Jia; Zhao, Ye; Liu, Bao-Yan

2014-02-01

To effectively guarantee quality of randomized controlld trial (RCT) of acupuncture and develop reasonable content and checklist of on-site quality control, influencing factors on quality of acupuncture RCT are analyzed and scientificity of quality control content and feasibility of on-site manipulation are put into overall consideration. Based on content and checklist of on-site quality control in National 11th Five-Year Plan Project Optimization of Comprehensive Treatment Plan for TCM in Prevention and Treatment of Serious Disease and Clinical Assessment on Generic Technology and Quality Control Research, it is proposed that on-site quality control of acupuncture RCT should be conducted with PICOST (patient, intervention, comparison, out come, site and time) as core, especially on quality control of interveners' skills and outcome assessment of blinding, and checklist of on-site quality control is developed to provide references for undertaking groups of the project.

Ultrafast web inspection with hybrid dispersion laser scanner.

PubMed

Chen, Hongwei; Wang, Chao; Yazaki, Akio; Kim, Chanju; Goda, Keisuke; Jalali, Bahram

2013-06-10

We report an ultrafast web inspector that operates at a 1000 times higher scan rate than conventional methods. This system is based on a hybrid dispersion laser scanner that performs line scans at nearly 100 MHz. Specifically, we demonstrate web inspection with detectable resolution of 48.6 μm/pixel (scan direction) × 23 μm (web flow direction) within a width of view of 6 mm at a record high scan rate of 90.9 MHz. We demonstrate the identification and evaluation of particles on silicon wafers. This method holds great promise for speeding up quality control and hence reducing manufacturing costs.

An operator interface design for a telerobotic inspection system

NASA Technical Reports Server (NTRS)

Kim, Won S.; Tso, Kam S.; Hayati, Samad

1993-01-01

The operator interface has recently emerged as an important element for efficient and safe interactions between human operators and telerobotics. Advances in graphical user interface and graphics technologies enable us to produce very efficient operator interface designs. This paper describes an efficient graphical operator interface design newly developed for remote surface inspection at NASA-JPL. The interface, designed so that remote surface inspection can be performed by a single operator with an integrated robot control and image inspection capability, supports three inspection strategies of teleoperated human visual inspection, human visual inspection with automated scanning, and machine-vision-based automated inspection.

Optical Inspection In Hostile Industrial Environments: Single-Sensor VS. Imaging Methods

NASA Astrophysics Data System (ADS)

Cielo, P.; Dufour, M.; Sokalski, A.

1988-11-01

On-line and unsupervised industrial inspection for quality control and process monitoring is increasingly required in the modern automated factory. Optical techniques are particularly well suited to industrial inspection in hostile environments because of their noncontact nature, fast response time and imaging capabilities. Optical sensors can be used for remote inspection of high temperature products or otherwise inaccessible parts, provided they are in a line-of-sight relation with the sensor. Moreover, optical sensors are much easier to adapt to a variety of part shapes, position or orientation and conveyor speeds as compared to contact-based sensors. This is an important requirement in a flexible automation environment. A number of choices are possible in the design of optical inspection systems. General-purpose two-dimensional (2-D) or three-dimensional (3-D) imaging techniques have advanced very rapidly in the last years thanks to a substantial research effort as well as to the availability of increasingly powerful and affordable hardware and software. Imaging can be realized using 2-D arrays or simpler one-dimensional (1-D) line-array detectors. Alternatively, dedicated single-spot sensors require a smaller amount of data processing and often lead to robust sensors which are particularly appropriate to on-line operation in hostile industrial environments. Many specialists now feel that dedicated sensors or clusters of sensors are often more effective for specific industrial automation and control tasks, at least in the short run. This paper will discuss optomechanical and electro-optical choices with reference to the design of a number of on-line inspection sensors which have been recently developed at our institute. Case studies will include real-time surface roughness evaluation on polymer cables extruded at high speed, surface characterization of hot-rolled or galvanized-steel sheets, temperature evaluation and pinhole detection in aluminum foil, multi

Quality control for the first large areas of triple-GEM chambers for the CMS endcaps

NASA Astrophysics Data System (ADS)

Abbaneo, D.; Abbas, M.; Abbrescia, M.; Abi Akl, M.; Aboamer, O.; Acosta, D.; Ahmad, A.; Ahmed, W.; Aleksandrov, A.; Altieri, P.; Asawatangtrakuldee, C.; Aspell, P.; Assran, Y.; Awan, I.; Bally, S.; Ban, Y.; Banerjee, S.; Barashko, V.; Barria, P.; Bencze, G.; Beni, N.; Benussi, L.; Bhopatkar, V.; Bianco, S.; Bos, J.; Bouhali, O.; Braghieri, A.; Braibant, S.; Buontempo, S.; Calabria, C.; Caponero, M.; Caputo, C.; Cassese, F.; Castaneda, A.; Cauwenbergh, S.; Cavallo, F. R.; Celik, A.; Choi, M.; Choi, S.; Christiansen, J.; Cimmino, A.; Colafranceschi, S.; Colaleo, A.; Conde Garcia, A.; Czellar, S.; Dabrowski, M. M.; De Lentdecker, G.; De Oliveira, R.; de Robertis, G.; Dildick, S.; Dorney, B.; Endroczi, G.; Errico, F.; Fenyvesi, A.; Ferry, S.; Furic, I.; Giacomelli, P.; Gilmore, J.; Golovtsov, V.; Guiducci, L.; Guilloux, F.; Gutierrez, A.; Hadjiiska, R. M.; Hauser, J.; Hoepfner, K.; Hohlmann, M.; Hoorani, H.; Iaydjiev, P.; Jeng, Y. G.; Kamon, T.; Karchin, P.; Korytov, A.; Krutelyov, S.; Kumar, A.; Kim, H.; Lee, J.; Lenzi, T.; Litov, L.; Loddo, F.; Madorsky, A.; Maerschalk, T.; Maggi, M.; Magnani, A.; Mal, P. K.; Mandal, K.; Marchioro, A.; Marinov, A.; Majumdar, N.; Merlin, J. A.; Mitselmakher, G.; Mohanty, A. K.; Mohapatra, A.; Molnar, J.; Muhammad, S.; Mukhopadhyay, S.; Naimuddin, M.; Nuzzo, S.; Oliveri, E.; Pant, L. M.; Paolucci, P.; Park, I.; Passeggio, G.; Pavlov, B.; Philipps, B.; Piccolo, D.; Postema, H.; Puig Baranac, A.; Radi, A.; Radogna, R.; Raffone, G.; Ranieri, A.; Rashevski, G.; Riccardi, C.; Rodozov, M.; Rodrigues, A.; Ropelewski, L.; RoyChowdhury, S.; Ryu, G.; Ryu, M. S.; Safonov, A.; Salva, S.; Saviano, G.; Sharma, A.; Sharma, A.; Sharma, R.; Shah, A. H.; Shopova, M.; Sturdy, J.; Sultanov, G.; Swain, S. K.; Szillasi, Z.; Talvitie, J.; Tatarinov, A.; Tuuva, T.; Tytgat, M.; Vai, I.; Van Stenis, M.; Venditti, R.; Verhagen, E.; Verwilligen, P.; Vitulo, P.; Volkov, S.; Vorobyev, A.; Wang, D.; Wang, M.; Yang, U.; Yang, Y.; Yonamine, R.; Zaganidis, N.; Zenoni, F.; Zhang, A.

2018-02-01

The CMS Collaboration plans to equip the very forward muon system with triple-GEM detectors that can withstand the environment of the High-Luminosity LHC. This project is at the final stages of R&D and moving to production. An unprecedented large area of several 100 m2 are to be instrumented with GEM detectors which will be produced in six different sites around the world. A common construction and quality control procedure is required to ensure the performance of each detector. The quality control steps will include optical inspection, cleaning and baking of all materials and parts used to build the detector, leakage current tests of the GEM foils, high voltage tests, gas leak tests of the chambers and monitoring pressure drop vs. time, gain calibration to know the optimal operation region of the detector, gain uniformity tests, and studying the efficiency, noise and tracking performance of the detectors in a cosmic stand using scintillators.

Automated optical inspection of liquid crystal display anisotropic conductive film bonding

NASA Astrophysics Data System (ADS)

Ni, Guangming; Du, Xiaohui; Liu, Lin; Zhang, Jing; Liu, Juanxiu; Liu, Yong

2016-10-01

Anisotropic conductive film (ACF) bonding is widely used in the liquid crystal display (LCD) industry. It implements circuit connection between screens and flexible printed circuits or integrated circuits. Conductive microspheres in ACF are key factors that influence LCD quality, because the conductive microspheres' quantity and shape deformation rate affect the interconnection resistance. Although this issue has been studied extensively by prior work, quick and accurate methods to inspect the quality of ACF bonding are still missing in the actual production process. We propose a method to inspect ACF bonding effectively by using automated optical inspection. The method has three steps. The first step is that it acquires images of the detection zones using a differential interference contrast (DIC) imaging system. The second step is that it identifies the conductive microspheres and their shape deformation rate using quantitative analysis of the characteristics of the DIC images. The final step is that it inspects ACF bonding using a back propagation trained neural network. The result shows that the miss rate is lower than 0.1%, and the false inspection rate is lower than 0.05%.

49 CFR 230.67 - Responsibility for inspection and repairs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives and Tenders § 230.67 Responsibility for inspection and repairs. The steam locomotive owner and/or operator shall inspect and repair all steam locomotives and tenders under their control. All defects...

24 CFR 968.140 - On-site inspections.

Code of Federal Regulations, 2011 CFR

2011-04-01

... inspection personnel during modernization, whether work is performed by contract or force account labor and with or without the services of an architect/engineer, to ensure work quality and progress. [58 FR...

46 CFR 153.812 - Inspection for Certificate of Inspection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Inspection for Certificate of Inspection. 153.812... CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Testing and Inspection § 153.812 Inspection for Certificate of Inspection. The rules governing the...

[Quality control in anesthesiology].

PubMed

Muñoz-Ramón, J M

1995-03-01

The process of quality control and auditing of anesthesiology allows us to evaluate care given by a service and solve problems that are detected. Quality control is a basic element of care giving and is only secondarily an area of academic research; it is therefore a meaningless effort if the information does not serve to improve departmental procedures. Quality assurance procedures assume certain infrastructural requirements and an initial period of implementation and adjustment. The main objectives of quality control are the reduction of morbidity and mortality due to anesthesia, assurance of the availability and proper management of resources and, finally, the well-being and safety of the patient.

42 CFR 456.611 - Reports on inspections.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.611 Reports on inspections. (a) The team must submit a...

42 CFR 456.607 - Notification before inspection.

Code of Federal Regulations, 2012 CFR

2012-10-01

....607 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.607 Notification before inspection. No facility may be...

42 CFR 456.611 - Reports on inspections.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.611 Reports on inspections. (a) The team must submit a...

42 CFR 456.611 - Reports on inspections.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.611 Reports on inspections. (a) The team must submit a...

42 CFR 456.606 - Frequency of inspections.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.606 Frequency of inspections. The team and the agency...

42 CFR 456.606 - Frequency of inspections.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.606 Frequency of inspections. The team and the agency...

42 CFR 456.607 - Notification before inspection.

Code of Federal Regulations, 2011 CFR

2011-10-01

....607 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.607 Notification before inspection. No facility may be...

42 CFR 456.606 - Frequency of inspections.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.606 Frequency of inspections. The team and the agency...

42 CFR 456.607 - Notification before inspection.

Code of Federal Regulations, 2014 CFR

2014-10-01

....607 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.607 Notification before inspection. No facility may be...

42 CFR 456.611 - Reports on inspections.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.611 Reports on inspections. (a) The team must submit a...

42 CFR 456.606 - Frequency of inspections.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.606 Frequency of inspections. The team and the agency...

42 CFR 456.607 - Notification before inspection.

Code of Federal Regulations, 2013 CFR

2013-10-01

....607 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.607 Notification before inspection. No facility may be...

Vision-Based Corrosion Detection Assisted by a Micro-Aerial Vehicle in a Vessel Inspection Application.

PubMed

Ortiz, Alberto; Bonnin-Pascual, Francisco; Garcia-Fidalgo, Emilio; Company-Corcoles, Joan P

2016-12-14

Vessel maintenance requires periodic visual inspection of the hull in order to detect typical defective situations of steel structures such as, among others, coating breakdown and corrosion. These inspections are typically performed by well-trained surveyors at great cost because of the need for providing access means (e.g., scaffolding and/or cherry pickers) that allow the inspector to be at arm's reach from the structure under inspection. This paper describes a defect detection approach comprising a micro-aerial vehicle which is used to collect images from the surfaces under inspection, particularly focusing on remote areas where the surveyor has no visual access, and a coating breakdown/corrosion detector based on a three-layer feed-forward artificial neural network. As it is discussed in the paper, the success of the inspection process depends not only on the defect detection software but also on a number of assistance functions provided by the control architecture of the aerial platform, whose aim is to improve picture quality. Both aspects of the work are described along the different sections of the paper, as well as the classification performance attained.

Vision-Based Corrosion Detection Assisted by a Micro-Aerial Vehicle in a Vessel Inspection Application

PubMed Central

Ortiz, Alberto; Bonnin-Pascual, Francisco; Garcia-Fidalgo, Emilio; Company-Corcoles, Joan P.

2016-01-01

Vessel maintenance requires periodic visual inspection of the hull in order to detect typical defective situations of steel structures such as, among others, coating breakdown and corrosion. These inspections are typically performed by well-trained surveyors at great cost because of the need for providing access means (e.g., scaffolding and/or cherry pickers) that allow the inspector to be at arm’s reach from the structure under inspection. This paper describes a defect detection approach comprising a micro-aerial vehicle which is used to collect images from the surfaces under inspection, particularly focusing on remote areas where the surveyor has no visual access, and a coating breakdown/corrosion detector based on a three-layer feed-forward artificial neural network. As it is discussed in the paper, the success of the inspection process depends not only on the defect detection software but also on a number of assistance functions provided by the control architecture of the aerial platform, whose aim is to improve picture quality. Both aspects of the work are described along the different sections of the paper, as well as the classification performance attained. PMID:27983627

Appendix G - Spill Prevention, Control, and Countermeasure (SPCC) Inspection Checklists - Onshore Oil Production, Drilling, and Workover Facilities

EPA Pesticide Factsheets

This checklist is designed to assist EPA inspectors in conducting a thorough and nationally consistent inspection of a facility’s compliance with the Spill Prevention, Control, and Countermeasure (SPCC) rule at 40 CFR part 112.

Control system of the inspection robots group applying auctions and multi-criteria analysis for task allocation

NASA Astrophysics Data System (ADS)

Panfil, Wawrzyniec; Moczulski, Wojciech

2017-10-01

In the paper presented is a control system of a mobile robots group intended for carrying out inspection missions. The main research problem was to define such a control system in order to facilitate a cooperation of the robots resulting in realization of the committed inspection tasks. Many of the well-known control systems use auctions for tasks allocation, where a subject of an auction is a task to be allocated. It seems that in the case of missions characterized by much larger number of tasks than number of robots it will be better if robots (instead of tasks) are subjects of auctions. The second identified problem concerns the one-sided robot-to-task fitness evaluation. Simultaneous assessment of the robot-to-task fitness and task attractiveness for robot should affect positively for the overall effectiveness of the multi-robot system performance. The elaborated system allows to assign tasks to robots using various methods for evaluation of fitness between robots and tasks, and using some tasks allocation methods. There is proposed the method for multi-criteria analysis, which is composed of two assessments, i.e. robot's concurrency position for task among other robots and task's attractiveness for robot among other tasks. Furthermore, there are proposed methods for tasks allocation applying the mentioned multi-criteria analysis method. The verification of both the elaborated system and the proposed tasks' allocation methods was carried out with the help of simulated experiments. The object under test was a group of inspection mobile robots being a virtual counterpart of the real mobile-robot group.

Betatron Application in Mobile and Relocatable Inspection Systems for Freight Transport Control

NASA Astrophysics Data System (ADS)

Chakhlov, S. V.; Kasyanov, S. V.; Kasyanov, V. A.; Osipov, S. P.; Stein, M. M.; Stein, A. M.; Xiaoming, Sun

2016-01-01

Accelerators with energy level up to 4 MeV having high level of penetration ability by steel equivalent are the popular to control oversize cargo transported by road, by railway and by river. Betatron's usage as cyclic induction accelerator has some advantages in comparison with linear accelerators and other sources. Tomsk Polytechnic University has developed many types of betatrons, most of them are being produced by separate affiliated company " Foton ". Article is shown the results of application of the betatrons in inspection custom systems.

40 CFR 763.85 - Inspection and reinspections.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Inspection and reinspections. 763.85 Section 763.85 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Asbestos-Containing Materials in Schools § 763.85 Inspection and reinspections. (a...

40 CFR 763.85 - Inspection and reinspections.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Inspection and reinspections. 763.85 Section 763.85 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Asbestos-Containing Materials in Schools § 763.85 Inspection and reinspections. (a...

40 CFR 763.85 - Inspection and reinspections.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Inspection and reinspections. 763.85 Section 763.85 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Asbestos-Containing Materials in Schools § 763.85 Inspection and reinspections. (a...

40 CFR 763.85 - Inspection and reinspections.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Inspection and reinspections. 763.85 Section 763.85 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Asbestos-Containing Materials in Schools § 763.85 Inspection and reinspections. (a...

40 CFR 763.85 - Inspection and reinspections.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Inspection and reinspections. 763.85 Section 763.85 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Asbestos-Containing Materials in Schools § 763.85 Inspection and reinspections. (a...

Operationalisation of service quality in household waste collection.

PubMed

Schulte, Nico Alexander; Gellenbeck, Klaus; Nelles, Michael

2017-04-01

Since 2007, there has been intensive discussion at European and national levels concerning the standardisation of services including those in the sector of waste management. The drafts of the European standard prEN 16250 and the German preliminary standard DIN SPEC 1108 are intended to establish a uniform definition of corresponding services and their (minimum) service levels. Their binding application in practice requires that systematic inspections be provided to ascertain to what degree a service has been carried out as agreed upon. However, both standardisation projects give only a few examples of potential quality characteristics and offer no concrete information concerning methods of measurement. Because intersectoral or cross-service quality inspections do not exist, there is a need for the development of specific quality inspections. The study introduced in this article examines the question of how the service quality of door-to-door waste collection can be systematically measured. To this end, the quality concept applied to the process of waste collection was first concretised and then operationalised using indicators. Based upon this, the methods of the quality inspections were developed and subjected to a trial of their applicability in a German waste management company. The methods for measuring and evaluating take into account, in addition to the different boundary conditions of collection, also the possible customer influence on the collection process and consequently on the service performed by the collection crew. In order to avoid time- and therefore cost-intensive exhaustive surveys, a multilevel random-controlled selection of survey units was developed, too. Based on the analysis of the measurement data, it was possible to determine specific time requirement values for the regular performance of the data surveys, as well as minimum sample sizes as a function of the number of container locations of the waste collection tours. On the basis of this

Field Operations and Enforcement Manual for Air Pollution Control. Volume III: Inspection Procedures for Specific Industries.

ERIC Educational Resources Information Center

Weisburd, Melvin I.

The Field Operations and Enforcement Manual for Air Pollution Control, Volume III, explains in detail the following: inspection procedures for specific sources, kraft pulp mills, animal rendering, steel mill furnaces, coking operations, petroleum refineries, chemical plants, non-ferrous smelting and refining, foundries, cement plants, aluminum…

Commercial jet fuel quality control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strauss, K.H.

1995-05-01

The paper discusses the purpose of jet fuel quality control between the refinery and the aircraft. It describes fixed equipment, including various types of filters, and the usefulness and limitations of this equipment. Test equipment is reviewed as are various surveillance procedures. These include the Air Transport Association specification ATA 103, the FAA Advisory Circular 150/5230-4, the International Air Transport Association Guidance Material for Fuel Quality Control and Fuelling Service and the Guidelines for Quality Control at Jointly Operated Fuel Systems. Some past and current quality control problems are briefly mentioned.

Estimated incident cost savings in shipping due to inspections.

PubMed

Knapp, Sabine; Bijwaard, Govert; Heij, Christiaan

2011-07-01

The effectiveness of safety inspections of ships has been analysed from various angles, but until now, relatively little attention has been given to translate risk reduction into incident cost savings. This paper provides a monetary quantification of the cost savings that can be attributed to port state control inspections and industry vetting inspections. The dataset consists of more than half a million ship arrivals between 2002 and 2007 and contains inspections of port state authorities in the USA and Australia and of three industry vetting regimes. The effect of inspections in reducing the risk of total loss accidents is estimated by means of duration models, in terms of the gained probability of survival. The monetary benefit of port state control inspections is estimated to range, on average, from about 70 to 190 thousand dollars, with median values ranging from about 20 to 45 thousand dollars. Industry inspections have even higher benefits, especially for tankers. The savings are in general higher for older and larger vessels, and also for vessels with undefined flag and unknown classification society. As inspection costs are relatively low in comparison to potential cost savings, the results underline the importance of determining ships with relatively high risk of total loss. Copyright © 2011 Elsevier Ltd. All rights reserved.

42 CFR 456.614 - Inspections by utilization review committee.

Code of Federal Regulations, 2010 CFR

2010-10-01

... HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS UTILIZATION CONTROL Inspections of Care in Intermediate Care Facilities and Institutions for Mental Diseases § 456.614 Inspections by utilization review...

Image formation simulation for computer-aided inspection planning of machine vision systems

NASA Astrophysics Data System (ADS)

Irgenfried, Stephan; Bergmann, Stephan; Mohammadikaji, Mahsa; Beyerer, Jürgen; Dachsbacher, Carsten; Wörn, Heinz

2017-06-01

In this work, a simulation toolset for Computer Aided Inspection Planning (CAIP) of systems for automated optical inspection (AOI) is presented along with a versatile two-robot-setup for verification of simulation and system planning results. The toolset helps to narrow down the large design space of optical inspection systems in interaction with a system expert. The image formation taking place in optical inspection systems is simulated using GPU-based real time graphics and high quality off-line-rendering. The simulation pipeline allows a stepwise optimization of the system, from fast evaluation of surface patch visibility based on real time graphics up to evaluation of image processing results based on off-line global illumination calculation. A focus of this work is on the dependency of simulation quality on measuring, modeling and parameterizing the optical surface properties of the object to be inspected. The applicability to real world problems is demonstrated by taking the example of planning a 3D laser scanner application. Qualitative and quantitative comparison results of synthetic and real images are presented.

Inspection of the interior surface of cylindrical vessels using optic fiber shearography

NASA Astrophysics Data System (ADS)

Liu, Bin; Wei, Quan; Tu, Jun; Arola, Dwayne D.; Zhang, Dongsheng

2017-09-01

In this study, a shearography system integrated with a coherent fiber-optic illumination and a fiber-optic imaging bundle is presented to inspect the quality of the interior surface of a cylindrical vessel for safety purposes. The specific optical arrangement is designed for the inspection of a certain area at a small working distance. The optical arrangement of the system was assembled and an aluminum honeycomb sample was evaluated to demonstrate the capability of the system. The important relationship between the image quality and the working distance, as well as the field of view, is discussed. The system has been applied for the inspection of the interior surface of a cylindrical vessel. The experimental results suggest that the shearography system integrated with optical and image fibers can effectively minimize the size of the inspection device and be capable of evaluating the interior surface of cylindrical structures.

Selection of suitable NDT methods for building inspection

NASA Astrophysics Data System (ADS)

Pauzi Ismail, Mohamad

2017-11-01

Construction of modern structures requires good quality concrete with adequate strength and durability. Several accidents occurred in the civil constructions and were reported in the media. Such accidents were due to poor workmanship and lack of systematic monitoring during the constructions. In addition, water leaking and cracking in residential houses was commonly reported too. Based on these facts, monitoring the quality of concrete in structures is becoming more and more important subject. This paper describes major Non-destructive Testing (NDT) methods for evaluating structural integrity of concrete building. Some interesting findings during actual NDT inspections on site are presented. The NDT methods used are explained, compared and discussed. The suitable methods are suggested as minimum NDT methods to cover parameters required in the inspection.

Estimation of process capability indices from the results of limit gauge inspection of dimensional parameters in machining industry

NASA Astrophysics Data System (ADS)

Masterenko, Dmitry A.; Metel, Alexander S.

2018-03-01

The process capability indices Cp, Cpk are widely used in the modern quality management as statistical measures of the ability of a process to produce output X within specification limits. The customer's requirement to ensure Cp ≥ 1.33 is often applied in contracts. Capability indices estimates may be calculated with the estimates of the mean µ and the variability 6σ, and for it, the quality characteristic in a sample of pieces should be measured. It requires, in turn, using advanced measuring devices and well-qualified staff. From the other hand, quality inspection by attributes, fulfilled with limit gauges (go/no-go) is much simpler and has a higher performance, but it does not give the numerical values of the quality characteristic. The described method allows estimating the mean and the variability of the process on the basis of the results of limit gauge inspection with certain lower limit LCL and upper limit UCL, which separates the pieces into three groups: where X < LCL, number of pieces is n1, where LCL ≤ X < UCL, n2 pieces, and where X ≥ UCL, n3 pieces. So-called Pittman-type estimates, developed by the author, are functions of n1, n2, n3 and allow calculation of the estimated µ and σ. Thus, Cp and Cpk also may be estimated without precise measurements. The estimates can be used in quality inspection of lots of pieces as well as in monitoring and control of the manufacturing process. It is very important for improving quality of articles in machining industry through their tolerance.

Speech input system for meat inspection and pathological coding used thereby

NASA Astrophysics Data System (ADS)

Abe, Shozo

Meat inspection is one of exclusive and important jobs of veterinarians though it is not well known in general. As the inspection should be conducted skillfully during a series of continuous operations in a slaughter house, development of automatic inspecting systems has been required for a long time. We employed a hand-free speech input system to record the inspecting data because inspecters have to use their both hands to treat the internals of catles and check their health conditions by necked eyes. The data collected by the inspectors are transfered to a speech recognizer and then stored as controlable data of each catle inspected. Control of terms such as pathological conditions to be input and their coding are also important in this speech input system and practical examples are shown.

48 CFR 46.202-2 - Government reliance on inspection by contractor.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract Quality Requirements 46.202-2 Government... the contractor to accomplish all inspection and testing needed to ensure that supplies or services acquired at or below the simplified acquisition threshold conform to contract quality requirements before...

40 CFR 75.21 - Quality assurance and quality control requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Quality assurance and quality control... PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Operation and Maintenance Requirements § 75.21 Quality assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner or...

21 CFR 179.21 - Sources of radiation used for inspection of food, for inspection of packaged food, and for...

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sources of radiation used for inspection of food, for inspection of packaged food, and for controlling food processing. 179.21 Section 179.21 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) IRRADIATION IN...

Label inspection of approximate cylinder based on adverse cylinder panorama

NASA Astrophysics Data System (ADS)

Lin, Jianping; Liao, Qingmin; He, Bei; Shi, Chenbo

2013-12-01

This paper presents a machine vision system for automated label inspection, with the goal to reduce labor cost and ensure consistent product quality. Firstly, the images captured from each single-camera are distorted, since the inspection object is approximate cylindrical. Therefore, this paper proposes an algorithm based on adverse cylinder projection, where label images are rectified by distortion compensation. Secondly, to overcome the limited field of viewing for each single-camera, our method novelly combines images of all single-cameras and build a panorama for label inspection. Thirdly, considering the shake of production lines and error of electronic signal, we design the real-time image registration to calculate offsets between the template and inspected images. Experimental results demonstrate that our system is accurate, real-time and can be applied for numerous real- time inspections of approximate cylinders.

Multiparameter magnetic inspection system with magnetic field control and plural magnetic transducers

DOEpatents

Jiles, David C.

1991-04-16

A multiparameter magnetic inspection system for providing an efficient and economical way to derive a plurality of independent measurements regarding magnetic properties of the magnetic material under investigation. The plurality of transducers for a plurality of different types of measurements operatively connected to the specimen. The transducers are in turn connected to analytical circuits for converting transducer signals to meaningful measurement signals of the magnetic properties of the specimen. The measurement signals are processed and can be simultaneously communicated to a control component. The measurement signals can also be selectively plotted against one another. The control component operates the functioning of the analytical circuits and operates and controls components to impose magnetic fields of desired characteristics upon the specimen. The system therefore allows contemporaneous or simultaneous derivation of the plurality of different independent magnetic properties of the material which can then be processed to derive characteristics of the material.

A Guide for Implementing Total Quality Management in the U.S. Coast Guard Reserve

DTIC Science & Technology

1991-12-01

quality field were reviewed. The main ones studied were: Total Quality (Deming 1988); Single-Minute Exchange of Die (SMED) (Shingo 1985); Poka - yoke (mistake...Productivity Press, 1985. Shingo, Shigeo. Zero Quality Control: Source Inspection and the Poka - Yoke System. Cambridge, MA: Productivity Press, 1986. Snead

Application of near infrared spectroscopy (NIRS) to non-destructive internal quality inspection of tomatoes

NASA Astrophysics Data System (ADS)

Tao, Xuemei; He, Yong

2006-09-01

The internal quality of tomato such as acidity and sugar content is important to its taste thus influences the market. The objective of this paper was to demonstrate the feasibility of using a near-infrared spectroscopy (NIRS) to investigate the relationship between sugar content and acidity of tomato and absorption spectra. The N1RS reflectance of nondestructive tomatoes was measured with a Visible/NJR spectrophotometer in 325-1075 nm range. The sugar content and acidity of tomato were obtained with a handhold sugar content meter and a PH meter. The reflectance data set was recorded and analyzed with some mathematic methods. The PLS (Partial least squares) calibration method was developed for converting the NIRS reflectance of tomato into the data which determined the acidity value. BP (Back propagation) neural network was used to set up the relationship between the NIRS reflectance of tomato and sugar content. The acidity values were detected with an accuracy of 9O% and the sugar contents determined by the BP network were also very close to the measurements (coefficient of correlation r2=0.8764). NW spectra analysis would be very useful in the nondestructive internal quality inspecting of tomato.

How do humans inspect BPMN models: an exploratory study.

PubMed

Haisjackl, Cornelia; Soffer, Pnina; Lim, Shao Yi; Weber, Barbara

2018-01-01

Even though considerable progress regarding the technical perspective on modeling and supporting business processes has been achieved, it appears that the human perspective is still often left aside. In particular, we do not have an in-depth understanding of how process models are inspected by humans, what strategies are taken, what challenges arise, and what cognitive processes are involved. This paper contributes toward such an understanding and reports an exploratory study investigating how humans identify and classify quality issues in BPMN process models. Providing preliminary answers to initial research questions, we also indicate other research questions that can be investigated using this approach. Our qualitative analysis shows that humans adapt different strategies on how to identify quality issues. In addition, we observed several challenges appearing when humans inspect process models. Finally, we present different manners in which classification of quality issues was addressed.

Quality control in gastrointestinal surgery.

PubMed

Ramírez-Barba, Ector Jaime; Arenas-Moya, Diego; Vázquez-Guerrero, Arturo

2011-01-01

We analyzed the Mexican legal framework, identifying the vectors that characterize quality and control in gastrointestinal surgery. Quality is contemplated in the health protection rights determined according to the Mexican Constitution, established in the general health law and included as a specific goal in the actual National Development Plan and Health Sector Plan. Quality control implies planning, verification and application of corrective measures. Mexico has implemented several quality strategies such as certification of hospitals and regulatory agreements by the General Salubrity Council, creation of the National Health Quality Committee, generation of Clinical Practice Guidelines and the Certification of Medical Specialties, among others. Quality control in gastrointestinal surgery must begin at the time of medical education and continue during professional activities of surgeons, encouraging multidisciplinary teamwork, knowledge, abilities, attitudes, values and skills that promote homogeneous, safe and quality health services for the Mexican population.

48 CFR 1646.301 - Contractor inspection requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Contractor inspection requirements. 1646.301 Section 1646.301 Federal Acquisition Regulations System OFFICE OF PERSONNEL MANAGEMENT FEDERAL EMPLOYEES HEALTH BENEFITS ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract...

48 CFR 1646.301 - Contractor inspection requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false Contractor inspection requirements. 1646.301 Section 1646.301 Federal Acquisition Regulations System OFFICE OF PERSONNEL MANAGEMENT FEDERAL EMPLOYEES HEALTH BENEFITS ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract...

48 CFR 1646.301 - Contractor inspection requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 6 2014-10-01 2014-10-01 false Contractor inspection requirements. 1646.301 Section 1646.301 Federal Acquisition Regulations System OFFICE OF PERSONNEL MANAGEMENT FEDERAL EMPLOYEES HEALTH BENEFITS ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract...

48 CFR 1646.301 - Contractor inspection requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 6 2013-10-01 2013-10-01 false Contractor inspection requirements. 1646.301 Section 1646.301 Federal Acquisition Regulations System OFFICE OF PERSONNEL MANAGEMENT FEDERAL EMPLOYEES HEALTH BENEFITS ACQUISITION REGULATION CONTRACT MANAGEMENT QUALITY ASSURANCE Contract...

2013 Annual Site Inspection and Monitoring Report for Uranium Mill Tailings Radiation Control Act Title II Disposal Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This report, in fulfillment of a license requirement, presents the results of long-term surveillance and maintenance activities conducted by the U.S. Department of Energy (DOE) Office of Legacy Management in 2013 at six uranium mill tailings disposal sites reclaimed under Title II of the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978. These activities verified that the UMTRCA Title II disposal sites remain in compliance with license requirements. DOE manages six UMTRCA Title II disposal sites under a general license granted by the U.S. Nuclear Regulatory Commission (NRC) established at Title 10 Code of Federal Regulations Part 40.28. Reclamationmore » and site transition activities continue at other sites, and DOE ultimately expects to manage approximately 27 Title II disposal sites. Long-term surveillance and maintenance activities and services for these disposal sites include inspecting and maintaining the sites; monitoring environmental media and institutional controls; conducting any necessary corrective action; and performing administrative, records, stakeholder services, and other regulatory functions. Annual site inspections and monitoring are conducted in accordance with site-specific long-term surveillance plans (LTSPs) and procedures established by DOE to comply with license requirements. Each site inspection is performed to verify the integrity of visible features at the site; to identify changes or new conditions that may affect the long-term performance of the site; and to determine the need, if any, for maintenance, follow-up inspections, or corrective action. LTSPs and site compliance reports are available online at http://www.lm.doe.gov« less

VerifEYE: a real-time meat inspection system for the beef processing industry

NASA Astrophysics Data System (ADS)

Kocak, Donna M.; Caimi, Frank M.; Flick, Rick L.; Elharti, Abdelmoula

2003-02-01

Described is a real-time meat inspection system developed for the beef processing industry by eMerge Interactive. Designed to detect and localize trace amounts of contamination on cattle carcasses in the packing process, the system affords the beef industry an accurate, high speed, passive optical method of inspection. Using a method patented by United States Department of Agriculture and Iowa State University, the system takes advantage of fluorescing chlorophyll found in the animal's diet and therefore the digestive track to allow detection and imaging of contaminated areas that may harbor potentially dangerous microbial pathogens. Featuring real-time image processing and documentation of performance, the system can be easily integrated into a processing facility's Hazard Analysis and Critical Control Point quality assurance program. This paper describes the VerifEYE carcass inspection and removal verification system. Results indicating the feasibility of the method, as well as field data collected using a prototype system during four university trials conducted in 2001 are presented. Two successful demonstrations using the prototype system were held at a major U.S. meat processing facility in early 2002.

48 CFR 1446.670 - Inspection, receiving and acceptance reports.

Code of Federal Regulations, 2014 CFR

2014-10-01

... each commercial shipping document or packing list, whether by manual or electronic means, for supplies... INTERIOR CONTRACT MANAGEMENT QUALITY ASSURANCE Material Inspection and Receiving Reports 1446.670...

48 CFR 1446.670 - Inspection, receiving and acceptance reports.

Code of Federal Regulations, 2012 CFR

2012-10-01

... each commercial shipping document or packing list, whether by manual or electronic means, for supplies... INTERIOR CONTRACT MANAGEMENT QUALITY ASSURANCE Material Inspection and Receiving Reports 1446.670...

48 CFR 1446.670 - Inspection, receiving and acceptance reports.

Code of Federal Regulations, 2010 CFR

2010-10-01

... each commercial shipping document or packing list, whether by manual or electronic means, for supplies... INTERIOR CONTRACT MANAGEMENT QUALITY ASSURANCE Material Inspection and Receiving Reports 1446.670...

48 CFR 1446.670 - Inspection, receiving and acceptance reports.

Code of Federal Regulations, 2013 CFR

2013-10-01

... each commercial shipping document or packing list, whether by manual or electronic means, for supplies... INTERIOR CONTRACT MANAGEMENT QUALITY ASSURANCE Material Inspection and Receiving Reports 1446.670...

48 CFR 1446.670 - Inspection, receiving and acceptance reports.

Code of Federal Regulations, 2011 CFR

2011-10-01

... each commercial shipping document or packing list, whether by manual or electronic means, for supplies... INTERIOR CONTRACT MANAGEMENT QUALITY ASSURANCE Material Inspection and Receiving Reports 1446.670...

General aviation fuel quality control

NASA Technical Reports Server (NTRS)

Poitz, H.

1983-01-01

Quality control measures for aviation gasoline, and some of the differences between quality control on avgas and mogas are discussed. One thing to keep in mind is that with motor gasoline you can always pull off to the side of the road. It's not so easy to do in an airplane. Consequently, there are reasons for having the tight specifications and the tight quality control measures on avgas as compared to motor gasoline.

Online aptitude automatic surface quality inspection system for hot rolled strips steel

NASA Astrophysics Data System (ADS)

Lin, Jin; Xie, Zhi-jiang; Wang, Xue; Sun, Nan-Nan

2005-12-01

Defects on the surface of hot rolled steel strips are main factors to evaluate quality of steel strips, an improved image recognition algorithm are used to extract the feature of Defects on the surface of steel strips. Base on the Machine vision and Artificial Neural Networks, establish a defect recognition method to select defect on the surface of steel strips. Base on these research. A surface inspection system and advanced algorithms for image processing to hot rolled strips is developed. Preparing two different fashion to lighting, adopting line blast vidicon of CCD on the surface steel strips on-line. Opening up capacity-diagnose-system with level the surface of steel strips on line, toward the above and undersurface of steel strips with ferric oxide, injure, stamp etc of defects on the surface to analyze and estimate. Miscarriage of justice and alternate of justice rate not preponderate over 5%.Geting hold of applications on some big enterprises of steel at home. Experiment proved that this measure is feasible and effective.

Surface Inspection Tool for Optical Detection of Surface Defects

NASA Technical Reports Server (NTRS)

Nurge, Mark; Youngquist, Robert; Dyer, Dustin

2013-01-01

The Space Shuttle Orbiter windows were damaged both by micrometeor impacts and by handling, and required careful inspection before they could be reused. The launch commit criteria required that no defect be deeper than a critical depth. The shuttle program used a refocus microscope to perform a quick pass/fail determination, and then followed up with mold impressions to better quantify any defect. However, the refocus microscope is slow and tedious to use due to its limited field of view, only focusing on one small area of glass at a time. Additionally, the unit is bulky and unable to be used in areas with tight access, such as defects near the window frame or on the glass inside the Orbiter due to interference with the dashboard. The surface inspection tool is a low-profile handheld instrument that provides two digital video images on a computer for monitoring surface defects. The first image is a wide-angle view to assist the user in locating defects. The second provides an enlarged view of a defect centered in the window of the first image. The focus is adjustable for each of the images. However, the enlarged view was designed to have a focal plane with a short depth. This allows the user to get a feel for the depth of different parts of the defect under inspection as the focus control is varied. A light source is also provided to illuminate the defect, precluding the need for separate lighting tools. The software provides many controls to adjust image quality, along with the ability to zoom digitally the images and to capture and store them for later processing.

Is Low-field NMR a Complementary Tool to GC-MS in Quality Control of Essential Oils? A Case Study: Patchouli Essential Oil.

PubMed

Krause, Andre; Wu, Yu; Tian, Runtao; van Beek, Teris A

2018-04-24

High-field NMR is an expensive and important quality control technique. In recent years, cheaper and simpler low-field NMR has become available as a new quality control technique. In this study, 60 MHz 1 H-NMR was compared with GC-MS and refractometry for the detection of adulteration of essential oils, taking patchouli essential oil as a test case. Patchouli essential oil is frequently adulterated, even today. In total, 75 genuine patchouli essential oils, 10 commercial patchouli essential oils, 10 other essential oils, 17 adulterants, and 1 patchouli essential oil, spiked at 20% with those adulterants, were measured. Visual inspection of the NMR spectra allowed for easy detection of 14 adulterants, while gurjun and copaiba balsams proved difficult and one adulterant could not be detected. NMR spectra of 10 random essential oils differed not only strongly from patchouli essential oil but also from one another, suggesting that fingerprinting by low-field NMR is not limited to patchouli essential oil. Automated chemometric evaluation of NMR spectra was possible by similarity analysis (Mahalanobis distance) based on the integration from 0.1 - 8.1 ppm in 0.01 ppm increments. Good quality patchouli essential oils were recognised as well as 15 of 17 deliberate adulterations. Visual qualitative inspection by GC-MS allowed for the detection of all volatile adulterants. Nonvolatile adulterants, and all but one volatile adulterant, could be detected by semiquantitation. Different chemometric approaches showed satisfactory results. Similarity analyses were difficult with nonvolatile adulterants. Refractive index measurements could detect only 8 of 17 adulterants. Due to advantages such as simplicity, rapidity, reproducibility, and ability to detect nonvolatile adulterants, 60 MHz 1 H-NMR is complimentary to GC-MS for quality control of essential oils. Georg Thieme Verlag KG Stuttgart · New York.

Assessing colonoscopic inspection skill using a virtual withdrawal simulation: a preliminary validation of performance metrics.

PubMed

Zupanc, Christine M; Wallis, Guy M; Hill, Andrew; Burgess-Limerick, Robin; Riek, Stephan; Plooy, Annaliese M; Horswill, Mark S; Watson, Marcus O; de Visser, Hans; Conlan, David; Hewett, David G

2017-07-12

The effectiveness of colonoscopy for diagnosing and preventing colon cancer is largely dependent on the ability of endoscopists to fully inspect the colonic mucosa, which they achieve primarily through skilled manipulation of the colonoscope during withdrawal. Performance assessment during live procedures is problematic. However, a virtual withdrawal simulation can help identify and parameterise actions linked to successful inspection, and offer standardised assessments for trainees. Eleven experienced endoscopists and 18 endoscopy novices (medical students) completed a mucosal inspection task during three simulated colonoscopic withdrawals. The two groups were compared on 10 performance metrics to preliminarily assess the validity of these measures to describe inspection quality. Four metrics were related to aspects of polyp detection: percentage of polyp markers found; number of polyp markers found per minute; percentage of the mucosal surface illuminated by the colonoscope (≥0.5 s); and percentage of polyp markers illuminated (≥2.5 s) but not identified. A further six metrics described the movement of the colonoscope: withdrawal time; linear distance travelled by the colonoscope tip; total distance travelled by the colonoscope tip; and distance travelled by the colonoscope tip due to movement of the up/down angulation control, movement of the left/right angulation control, and axial shaft rotation. Statistically significant experienced-novice differences were found for 8 of the 10 performance metrics (p's < .005). Compared with novices, experienced endoscopists inspected more of the mucosa and detected more polyp markers, at a faster rate. Despite completing the withdrawals more quickly than the novices, the experienced endoscopists also moved the colonoscope more in terms of linear distance travelled and overall tip movement, with greater use of both the up/down angulation control and axial shaft rotation. However, the groups did not differ in the

40 CFR 63.926 - Inspection and monitoring requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) National Emission Standards for Containers § 63.926 Inspection and monitoring requirements. (a) Owners and operators of containers using either Container Level 1 or Container Level 2 controls in... 40 Protection of Environment 11 2012-07-01 2012-07-01 false Inspection and monitoring requirements...

40 CFR 63.926 - Inspection and monitoring requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Containers § 63.926 Inspection and monitoring requirements. (a) Owners and operators of containers using either Container Level 1 or Container Level 2 controls in... 40 Protection of Environment 10 2011-07-01 2011-07-01 false Inspection and monitoring requirements...

40 CFR 63.926 - Inspection and monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) National Emission Standards for Containers § 63.926 Inspection and monitoring requirements. (a) Owners and operators of containers using either Container Level 1 or Container Level 2 controls in... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Inspection and monitoring requirements...

40 CFR 63.926 - Inspection and monitoring requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) National Emission Standards for Containers § 63.926 Inspection and monitoring requirements. (a) Owners and operators of containers using either Container Level 1 or Container Level 2 controls in... 40 Protection of Environment 11 2013-07-01 2013-07-01 false Inspection and monitoring requirements...

40 CFR 63.926 - Inspection and monitoring requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) National Emission Standards for Containers § 63.926 Inspection and monitoring requirements. (a) Owners and operators of containers using either Container Level 1 or Container Level 2 controls in... 40 Protection of Environment 11 2014-07-01 2014-07-01 false Inspection and monitoring requirements...

Multiparameter magnetic inspection system with magnetic field control and plural magnetic transducers

DOEpatents

Jiles, D.C.

1991-04-16

A multiparameter magnetic inspection system is disclosed for providing an efficient and economical way to derive a plurality of independent measurements regarding magnetic properties of the magnetic material under investigation. The plurality of transducers for a plurality of different types of measurements operatively connected to the specimen. The transducers are in turn connected to analytical circuits for converting transducer signals to meaningful measurement signals of the magnetic properties of the specimen. The measurement signals are processed and can be simultaneously communicated to a control component. The measurement signals can also be selectively plotted against one another. The control component operates the functioning of the analytical circuits and operates and controls components to impose magnetic fields of desired characteristics upon the specimen. The system therefore allows contemporaneous or simultaneous derivation of the plurality of different independent magnetic properties of the material which can then be processed to derive characteristics of the material. 1 figure.