Quality-Assurance/Quality-Control Manual for Collection and Analysis of Water-Quality Data in the Ohio District, US Geological Survey

USGS Publications Warehouse

Francy, D.S.; Jones, A.L.; Myers, Donna N.; Rowe, G.L.; Eberle, Michael; Sarver, K.M.

1998-01-01

The U.S. Geological Survey (USGS), Water Resources Division (WRD), requires that quality-assurance/quality-control (QA/QC) activities be included in any sampling and analysis program. Operational QA/QC procedures address local needs while incorporating national policies. Therefore, specific technical policies were established for all activities associated with water-quality project being done by the Ohio District. The policies described in this report provide Ohio District personnel, cooperating agencies, and others with a reference manual on QA/QC procedures that are followed in collecitng and analyzing water-quality samples and reporting water-quality information in the Ohio District. The project chief, project support staff, District Water-Quality Specialist, and District Laboratory Coordinator are all involved in planning and implementing QA/QC activities at the district level. The District Chief and other district-level managers provide oversight, and the Regional Water-Quality Specialist, Office of Water Quality (USGS headquarters), and the Branch of Quality Systems within the Office of Water Quality create national QA/QC polices and provide assistance to District personnel. In the literature, the quality of all measurement data is expressed in terms of precision, variability, bias, accuracy, completeness, representativeness, and comparability. In the Ohio District, bias and variability will be used to describe quality-control data generated from samples in the field and laboratory. Each project chief must plan for implementation and financing of QA/QC activities necessary to achieve data-quality objectives. At least 15 percent of the total project effort must be directed toward QA/QC activities. Of this total, 5-10 percent will be used for collection and analysis of quality-control samples. This is an absolute minimum, and more may be required based on project objectives. Proper techniques must be followed in the collection and processing of surface

Manual control models of industrial management

NASA Technical Reports Server (NTRS)

Crossman, E. R. F. W.

1972-01-01

The industrial engineer is often required to design and implement control systems and organization for manufacturing and service facilities, to optimize quality, delivery, and yield, and minimize cost. Despite progress in computer science most such systems still employ human operators and managers as real-time control elements. Manual control theory should therefore be applicable to at least some aspects of industrial system design and operations. Formulation of adequate model structures is an essential prerequisite to progress in this area; since real-world production systems invariably include multilevel and multiloop control, and are implemented by timeshared human effort. A modular structure incorporating certain new types of functional element, has been developed. This forms the basis for analysis of an industrial process operation. In this case it appears that managerial controllers operate in a discrete predictive mode based on fast time modelling, with sampling interval related to plant dynamics. Successive aggregation causes reduced response bandwidth and hence increased sampling interval as a function of level.

Water Quality Monitoring Manual.

ERIC Educational Resources Information Center

Mason, Fred J.; Houdart, Joseph F.

This manual is designed for students involved in environmental education programs dealing with water pollution problems. By establishing a network of Environmental Monitoring Stations within the educational system, four steps toward the prevention, control, and abatement of water pollution are proposed. (1) Train students to recognize, monitor,…

46 CFR 62.25-10 - Manual alternate control systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... automatic primary control system failure; (2) Be suitable for manual control for prolonged periods; (3) Be... 46 Shipping 2 2011-10-01 2011-10-01 false Manual alternate control systems. 62.25-10 Section 62.25... AUTOMATION General Requirements for All Automated Vital Systems § 62.25-10 Manual alternate control systems...

PQLX: A seismic data quality control system description, applications, and users manual

USGS Publications Warehouse

McNamara, Daniel E.; Boaz, Richard I.

2011-01-01

Earthquake Information Center (NEIC), the USGS Albuquerque Seismological Laboratory (ASL), and the Incorporated Research Institutions in Seismology (IRIS) Data Management Center (DMC) for station monitoring and instrument response quality control. The PQLX system is available to the community at large through the U.S. Geological Survey (USGS) (http://ehpm-earthquake.wr.usgs.gov/research/software/pqlx.php) and IRIS (http://www.iris.edu/software/pqlx). Also provided is a fully searchable website for bug reporting and enhancement requests (http://wush.net/bugzilla/PQLX). The first part of this document aims to describe and illustrate some of the features and capabilities of the software. The second part of this document is a detailed users manual that covers installation procedures, system requirements, operations, bug reporting, and software components (Appendix).

WIM data analyst's manual

DOT National Transportation Integrated Search

2010-06-01

This manual provides information and recommended procedures to be utilized by an agencys Weigh-in-Motion (WIM) Office Data Analyst to perform validation and quality control (QC) checks of WIM traffic data. This manual focuses on data generated by ...

Inverse simulation system for manual-controlled rendezvous and docking based on artificial neural network

NASA Astrophysics Data System (ADS)

Zhou, Wanmeng; Wang, Hua; Tang, Guojin; Guo, Shuai

2016-09-01

The time-consuming experimental method for handling qualities assessment cannot meet the increasing fast design requirements for the manned space flight. As a tool for the aircraft handling qualities research, the model-predictive-control structured inverse simulation (MPC-IS) has potential applications in the aerospace field to guide the astronauts' operations and evaluate the handling qualities more effectively. Therefore, this paper establishes MPC-IS for the manual-controlled rendezvous and docking (RVD) and proposes a novel artificial neural network inverse simulation system (ANN-IS) to further decrease the computational cost. The novel system was obtained by replacing the inverse model of MPC-IS with the artificial neural network. The optimal neural network was trained by the genetic Levenberg-Marquardt algorithm, and finally determined by the Levenberg-Marquardt algorithm. In order to validate MPC-IS and ANN-IS, the manual-controlled RVD experiments on the simulator were carried out. The comparisons between simulation results and experimental data demonstrated the validity of two systems and the high computational efficiency of ANN-IS.

Manual traffic control for planned special events and emergencies.

DOT National Transportation Integrated Search

2015-11-01

Manual traffic control is a common intersection control strategy in which trained personnel, : typically police law enforcement officers, allocate intersection right-of-way to approaching vehicles. : Manual intersection control is a key part of manag...

TA-55 change control manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blum, T.W.; Selvage, R.D.; Courtney, K.H.

This manual is the guide for initiating change at the Plutonium Facility, which handles the processing of plutonium as well as research on plutonium metallurgy. It describes the change and work control processes employed at TA-55 to ensure that all proposed changes are properly identified, reviewed, approved, implemented, tested, and documented so that operations are maintained within the approved safety envelope. All Laboratory groups, their contractors, and subcontractors doing work at TA-55 follow requirements set forth herein. This manual applies to all new and modified processes and experiments inside the TA-55 Plutonium Facility; general plant project (GPP) and line itemmore » funded construction projects at TA-55; temporary and permanent changes that directly or indirectly affect structures, systems, or components (SSCs) as described in the safety analysis, including Facility Control System (FCS) software; and major modifications to procedures. This manual does not apply to maintenance performed on process equipment or facility SSCs or the replacement of SSCs or equipment with documented approved equivalents.« less

Teaching Quality Evaluation: Online vs Manually, Facts and Myths

ERIC Educational Resources Information Center

Esmael, Salman

2017-01-01

Aim/Purpose: This study aimed to examine whether there is a difference between manual feedback and online feedback with regard to feedback quality, respondents' percentage, reliability and the amount of verbal comments written by students. Background: The quality of teaching is an important component of academic work. There are various methods for…

Aquatic Pest Control. Manual 99.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Agricultural Experiment Station.

This training manual provides information needed to meet the minimum EPA standards for certification as a commercial applicator of pesticides in the aquatic pest control category. The text discusses various water use situations; aquatic weed identification; herbicide use and effects; and aquatic insects and their control. (CS)

Sixteenth Annual Conference on Manual Control

NASA Technical Reports Server (NTRS)

1982-01-01

Manual control is discussed in terms of operator modeling, measurement of human response, mental workload, pilot/operator opinion, effects of motion, aircraft displays, supervisory control, automobile driving, and remote manipulation.

CONTROL ROOM WITH SPRINKLER SYSTEM CONTROLS, INCLUDING MANUAL CONTROL BOXES ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CONTROL ROOM WITH SPRINKLER SYSTEM CONTROLS, INCLUDING MANUAL CONTROL BOXES FOR THE VENTILATION SYSTEM AND A PLC SWITCH FOR AUTOMATIC CO (CARBON MONOXIDE) SYSTEM. THE AIR TESTING SYSTEM IS FREE STANDING AND THE FANS ARE COMPUTER-OPERATED. - Alaskan Way Viaduct and Battery Street Tunnel, Seattle, King County, WA

MASQOT: a method for cDNA microarray spot quality control

PubMed Central

Bylesjö, Max; Eriksson, Daniel; Sjödin, Andreas; Sjöström, Michael; Jansson, Stefan; Antti, Henrik; Trygg, Johan

2005-01-01

Background cDNA microarray technology has emerged as a major player in the parallel detection of biomolecules, but still suffers from fundamental technical problems. Identifying and removing unreliable data is crucial to prevent the risk of receiving illusive analysis results. Visual assessment of spot quality is still a common procedure, despite the time-consuming work of manually inspecting spots in the range of hundreds of thousands or more. Results A novel methodology for cDNA microarray spot quality control is outlined. Multivariate discriminant analysis was used to assess spot quality based on existing and novel descriptors. The presented methodology displays high reproducibility and was found superior in identifying unreliable data compared to other evaluated methodologies. Conclusion The proposed methodology for cDNA microarray spot quality control generates non-discrete values of spot quality which can be utilized as weights in subsequent analysis procedures as well as to discard spots of undesired quality using the suggested threshold values. The MASQOT approach provides a consistent assessment of spot quality and can be considered an alternative to the labor-intensive manual quality assessment process. PMID:16223442

Natural Language Processing As an Alternative to Manual Reporting of Colonoscopy Quality Metrics

PubMed Central

RAJU, GOTTUMUKKALA S.; LUM, PHILLIP J.; SLACK, REBECCA; THIRUMURTHI, SELVI; LYNCH, PATRICK M.; MILLER, ETHAN; WESTON, BRIAN R.; DAVILA, MARTA L.; BHUTANI, MANOOP S.; SHAFI, MEHNAZ A.; BRESALIER, ROBERT S.; DEKOVICH, ALEXANDER A.; LEE, JEFFREY H.; GUHA, SUSHOVAN; PANDE, MALA; BLECHACZ, BORIS; RASHID, ASIF; ROUTBORT, MARK; SHUTTLESWORTH, GLADIS; MISHRA, LOPA; STROEHLEIN, JOHN R.; ROSS, WILLIAM A.

2015-01-01

BACKGROUND & AIMS The adenoma detection rate (ADR) is a quality metric tied to interval colon cancer occurrence. However, manual extraction of data to calculate and track the ADR in clinical practice is labor-intensive. To overcome this difficulty, we developed a natural language processing (NLP) method to identify patients, who underwent their first screening colonoscopy, identify adenomas and sessile serrated adenomas (SSA). We compared the NLP generated results with that of manual data extraction to test the accuracy of NLP, and report on colonoscopy quality metrics using NLP. METHODS Identification of screening colonoscopies using NLP was compared with that using the manual method for 12,748 patients who underwent colonoscopies from July 2010 to February 2013. Also, identification of adenomas and SSAs using NLP was compared with that using the manual method with 2259 matched patient records. Colonoscopy ADRs using these methods were generated for each physician. RESULTS NLP correctly identified 91.3% of the screening examinations, whereas the manual method identified 87.8% of them. Both the manual method and NLP correctly identified examinations of patients with adenomas and SSAs in the matched records almost perfectly. Both NLP and manual method produce comparable values for ADR for each endoscopist as well as the group as a whole. CONCLUSIONS NLP can correctly identify screening colonoscopies, accurately identify adenomas and SSAs in a pathology database, and provide real-time quality metrics for colonoscopy. PMID:25910665

Development of the Coordination between Posture and Manual Control

ERIC Educational Resources Information Center

Haddad, Jeffrey M.; Claxton, Laura J.; Keen, Rachel; Berthier, Neil E.; Riccio, Gary E.; Hamill, Joseph; Van Emmerik, Richard E. A.

2012-01-01

Studies have suggested that proper postural control is essential for the development of reaching. However, little research has examined the development of the coordination between posture and manual control throughout childhood. We investigated the coordination between posture and manual control in children (7- and 10-year-olds) and adults during…

Manual-control Analysis Applied to the Money-supply Control Task

NASA Technical Reports Server (NTRS)

Wingrove, R. C.

1984-01-01

The recent procedure implemented by the Federal Reserve Board to control the money supply is formulated in the form of a tracking model as used in the study of manual-control tasks. Using this model, an analysis is made to determine the effect of monetary control on the fluctuations in economic output. The results indicate that monetary control can reduce the amplitude of fluctuations at frequencies near the region of historic business cycles. However, with significant time lags in the control loop, monetary control tends to increase the amplitude of the fluctuations at the higher frequencies. How the investigator or student can use the tools developed in the field of manual-control analysis to study the nature of economic fluctuations and to examine different strategies for stabilization is examined.

A corrosion control manual for rail rapid transit

NASA Technical Reports Server (NTRS)

Gilbert, L. O.; Fitzgerald, J. F., II; Menke, J. T.

1982-01-01

In 1979, during the planning stage of the Metropolitan Dade County Transit System, the need was expressed for a corrosion control manual oriented to urban rapid transit system use. This manual responds to that need. The objective of the manual is to aid rail rapid transit agencies by providing practical solutions to selected corrosion problems. The scope of the manual encompasses corrosion problems of the facilities of rapid transit systems: structures and tracks, platforms and stations, power and signals, and cars. It also discusses stray electric current corrosion. Both design and maintenance solutions are provided for each problem. Also included are descriptions of the types of corrosion and their causes, descriptions of rapid transit properties, a list of corrosion control committees and NASA, DOD, and ASTM specifications and design criteria to which reference is made in the manual. A bibliography of papers and excerpts of reports and a glossary of frequency used terms are provided.

School Indoor Air Quality Best Management Practices Manual.

ERIC Educational Resources Information Center

Hall, Richard; Ellis, Richard; Hardin, Tim

This manual, written in response to requirements of the Washington State legislature, focuses on practices which can be undertaken during the siting, design, construction, or renovation of a school, recommends practices to help ensure good indoor air quality during building occupancy, and suggests protocols and useful reference documents for…

Automated manual transmission controller

DOEpatents

Lawrie, Robert E.; Reed, Jr., Richard G.; Bernier, David R.

1999-12-28

A powertrain system for a hybrid vehicle. The hybrid vehicle includes a heat engine, such as a diesel engine, and an electric machine, which operates as both an electric motor and an alternator, to power the vehicle. The hybrid vehicle also includes a manual-style transmission configured to operate as an automatic transmission from the perspective of the driver. The engine and the electric machine drive an input shaft which in turn drives an output shaft of the transmission. In addition to driving the transmission, the electric machine regulates the speed of the input shaft in order to synchronize the input shaft during either an upshift or downshift of the transmission by either decreasing or increasing the speed of the input shaft. When decreasing the speed of the input shaft, the electric motor functions as an alternator to produce electrical energy which may be stored by a storage device. Operation of the transmission is controlled by a transmission controller which receives input signals and generates output signals to control shift and clutch motors to effect smooth launch, upshift shifts, and downshifts of the transmission, so that the transmission functions substantially as an automatic transmission from the perspective of the driver, while internally substantially functioning as a manual transmission.

Forest Pest Control. Manual 94.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Agricultural Experiment Station.

This training manual provides information needed to meet the minimum EPA standards for certification as a commercial applicator of pesticides in forest pest control. The text discusses disease problems, insects, and herbicide use in both established forests and nurseries. (CS)

Organic Analyses in Water Quality Control Programs. Training Manual.

ERIC Educational Resources Information Center

Office of Water Program Operations (EPA), Cincinnati, OH. National Training and Operational Technology Center.

This document is a lecture/laboratory manual dealing with the analysis of selected organic pollutants. It is intended for use by those having little or no experience in the field, but having one year (or equivalent) of college organic chemistry, and having basic laboratory skills (volumetric glassware, titration, analytical and trip balances).…

46 CFR 62.25-10 - Manual alternate control systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Manual alternate control systems. 62.25-10 Section 62.25-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION General Requirements for All Automated Vital Systems § 62.25-10 Manual alternate control systems...

Waste Water Plant Operators Manual.

ERIC Educational Resources Information Center

Washington State Coordinating Council for Occupational Education, Olympia.

This manual for sewage treatment plant operators was prepared by a committee of operators, educators, and engineers for use as a reference text and handbook and to serve as a training manual for short course and certification programs. Sewage treatment plant operators have a responsibility in water quality control; they are the principal actors in…

Investigation of piloting aids for manual control of hypersonic maneuvers

NASA Technical Reports Server (NTRS)

Raney, David L.; Phillips, Michael R.; Person, Lee H., Jr.

1995-01-01

An investigation of piloting aids designed to provide precise maneuver control for an air-breathing hypersonic vehicle is described. Stringent constraints and nonintuitive high-speed flight effects associated with maneuvering in the hypersonic regime raise the question of whether manual control of such a vehicle should even be considered. The objectives of this research were to determine the extent of manual control that is desirable for a vehicle maneuvering in this regime and to identify the form of aids that must be supplied to the pilot to make such control feasible. A piloted real-time motion-based simulation of a hypersonic vehicle concept was used for this study, and the investigation focused on a single representative cruise turn maneuver. Piloting aids, which consisted of an auto throttle, throttle director, autopilot, flight director, and two head-up display configurations, were developed and evaluated. Two longitudinal control response types consisting of a rate-command/attitude-hold system and a load factor-rate/load-factor-hold system were also compared. The complete set of piloting aids, which consisted of the autothrottle, throttle director, and flight director, improved the average Cooper-Harper flying qualities ratings from 8 to 2.6, even though identical inner-loop stability and control augmentation was provided in all cases. The flight director was determined to be the most critical of these aids, and the cruise turn maneuver was unachievable to adequate performance specifications in the absence of this flight director.

Agricultural Electricity. Electric Controls. Student Manual. Report No. 820/20.

ERIC Educational Resources Information Center

Benson, Robert T.

Addressed to the student, this manual presents terms, abbreviations, and symbols used in discussing manual or automatic control of the flow of electric current. Diagrams accompany discussion of the following types of control devices and principles of operation: Heat sensitive controls (thermostats, thermal relays), light sensitive controls…

Theoretical linear approach to the combined man-manipulator system in manual control of an aircraft

NASA Technical Reports Server (NTRS)

Brauser, K.

1981-01-01

An approach to the calculation of the dynamic characteristics of the combined man manipulator system in manual aircraft control was derived from a model of the neuromuscular system. This model combines the neuromuscular properties of man with the physical properties of the manipulator system which is introduced as pilot manipulator model into the manual aircraft control. The assumption of man as a quasilinear and time invariant control operator adapted to operating states, depending on the flight phases, of the control system gives rise to interesting solutions of the frequency domain transfer functions of both the man manipulator system and the closed loop pilot aircraft control system. It is shown that it is necessary to introduce the complete precision pilot manipulator model into the closed loop pilot aircraft transfer function in order to understand the well known handling quality criteria, and to derive these criteria directly from human operator properties.

Microbial ecology laboratory procedures manual NASA/MSFC

NASA Technical Reports Server (NTRS)

Huff, Timothy L.

1990-01-01

An essential part of the efficient operation of any microbiology laboratory involved in sample analysis is a standard procedures manual. The purpose of this manual is to provide concise and well defined instructions on routine technical procedures involving sample analysis and methods for monitoring and maintaining quality control within the laboratory. Of equal importance is the safe operation of the laboratory. This manual outlines detailed procedures to be followed in the microbial ecology laboratory to assure safety, analytical control, and validity of results.

Quality control in urinalysis.

PubMed

Takubo, T; Tatsumi, N

1999-01-01

Quality control (QC) has been introduced in laboratories, and QC surveys in urinalysis have been performed by College of American Pathologist, by Japanese Association of Medical Technologists, by Osaka Medical Association and by manufacturers. QC survey in urinalysis for synthetic urine by the reagent strip and instrument made in same manufacturer, and by an automated urine cell analyser provided satisfactory results among laboratories. QC survey in urinalysis for synthetic urine by the reagent strips and instruments made by various manufacturers indicated differences in the determination values among manufacturers, and between manual and automated methods because the reagent strips and instruments have different characteristics, respectively. QC photo survey in urinalysis on the microscopic photos of urine sediment constituents indicated differences in the identification of cells among laboratories. From the results, it is necessary to standardize a reagent strip method, manual and automated methods, and synthetic urine.

A simulation study of emergency lunar escape to orbit using several simplified manual guidance and control techniques

NASA Technical Reports Server (NTRS)

Middleton, D. B.; Hurt, G. J., Jr.

1971-01-01

A fixed-base piloted simulator investigation has been made of the feasibility of using any of several manual guidance and control techniques for emergency lunar escape to orbit with very simplified, lightweight vehicle systems. The escape-to-orbit vehicles accommodate two men, but one man performs all of the guidance and control functions. Three basic attitude-control modes and four manually executed trajectory-guidance schemes were used successfully during approximately 125 simulated flights under a variety of conditions. These conditions included thrust misalinement, uneven propellant drain, and a vehicle moment-of-inertia range of 250 to 12,000 slugs per square foot. Two types of results are presented - orbit characteristics and pilot ratings of vehicle handling qualities.

Twenty-First Annual Conference on Manual Control

NASA Technical Reports Server (NTRS)

Miller, R. A. (Compiler); Jagacinski, R. J. (Compiler)

1986-01-01

The proceedings of the entitled conference are presented. Twenty-nine manuscripts and eight abstracts pertaining to workload, attention and errors, controller evaluation, movement skills, coordination and decision making, display evaluation and human operator modeling and manual control.

Proceedings, 13th Annual Conference on Manual Control

NASA Technical Reports Server (NTRS)

1977-01-01

Theoretical aspects of manual control theory are discussed. Specific topics covered include: tracking; performance, attention allocation, and mental load; surface vehicle control; monitoring behavior and supervisory control; manipulators and prosthetics; aerospace vehicle control; motion and visual cues; and displays and controls.

Regulation of dynamic postural control to attend manual steadiness constraints.

PubMed

Teixeira, Luis Augusto; Coutinho, Joane Figueiredo Serpa; Coelho, Daniel Boari

2018-05-02

In daily living activities, performance of spatially accurate manual movements in upright stance depends on postural stability. In the present investigation, we aimed to evaluate the effect of the required manual steadiness (task constraint) on the regulation of dynamic postural control. A single group of young participants (n=20) were evaluated in the performance of a dual posturo-manual task of balancing on a platform oscillating in sinusoidal translations at 0.4 Hz (low) or 1 Hz (high) frequencies while stabilizing a cylinder on a handheld tray. Manual task constraint was manipulated by comparing the conditions of keeping the cylinder stationary on its flat or round side, corresponding to low and high manual task constraints, respectively. Results showed that in the low oscillation frequency the high manual task constraint led to lower oscillation amplitudes of the head, center of mass, and tray, in addition to higher relative phase values between ankle/hip-shoulder oscillatory rotations and between center of mass/center of pressure-feet oscillations as compared to values observed in the low manual task constraint. Further analyses showed that the high manual task constraint also affected variables related to both postural (increased amplitudes of center of pressure oscillation) and manual (increased amplitude of shoulder rotations) task components in the high oscillation frequency. These results suggest that control of a dynamic posturo-manual task is modulated in distinct parameters to attend the required manual steadiness in a complex and flexible way.

An Evaluation of the Work and Life Conditions and the Quality of Life in 60 to 65 Year-Old White-Collar Employees, Manual Workers, and Unemployed Controls.

PubMed

Sołtysik, Bartłomiej K; Kroc, Łukasz; Pigłowska, Małgorzata; Guligowska, Agnieszka; Śmigielski, Janusz; Kostka, Tomasz

2017-05-01

Assessment of the work and life conditions of 60 to 65-year-old seniors with regard to type of work and quality of life (QoL). The European Foundation for Improvement of Living and Working Conditions Questionnaire and the EuroQol 5D were used to evaluate work and life conditions and QoL in the three age- and sex-matched 60 to 65-year-old groups (white-collar, manual workers, and unemployed subjects, 100 each group, 50% of women). Manual workers and unemployed subjects had lower QoL score (0 to 100 point scale) than white-collar workers (accordingly 72.2; 71.2; 76.2; P < 0.05). In working subjects (n = 200), QoL was inversely associated with reported health problems (P < 0.01) and directly related to quality of work (P < 0.001). In the group of manual workers (n = 100), QoL indices were influenced by health factors and quality of work, while in the intellectual group (n = 100) mainly by health factors. Quality of work and health assessment are the main domains that influence older workers' QoL and may contribute to the shortening of the work period and accelerated transfer to retirement. Quality of work assessment seems especially important in older manual workers.

Foot Pedals for Spacecraft Manual Control

NASA Technical Reports Server (NTRS)

Love, Stanley G.; Morin, Lee M.; McCabe, Mary

2010-01-01

Fifty years ago, NASA decided that the cockpit controls in spacecraft should be like the ones in airplanes. But controls based on the stick and rudder may not be best way to manually control a vehicle in space. A different method is based on submersible vehicles controlled with foot pedals. A new pilot can learn the sub's control scheme in minutes and drive it hands-free. We are building a pair of foot pedals for spacecraft control, and will test them in a spacecraft flight simulator.

Sharing control with haptics: seamless driver support from manual to automatic control.

PubMed

Mulder, Mark; Abbink, David A; Boer, Erwin R

2012-10-01

Haptic shared control was investigated as a human-machine interface that can intuitively share control between drivers and an automatic controller for curve negotiation. As long as automation systems are not fully reliable, a role remains for the driver to be vigilant to the system and the environment to catch any automation errors. The conventional binary switches between supervisory and manual control has many known issues, and haptic shared control is a promising alternative. A total of 42 respondents of varying age and driving experience participated in a driving experiment in a fixed-base simulator, in which curve negotiation behavior during shared control was compared to during manual control, as well as to three haptic tunings of an automatic controller without driver intervention. Under the experimental conditions studied, the main beneficial effect of haptic shared control compared to manual control was that less control activity (16% in steering wheel reversal rate, 15% in standard deviation of steering wheel angle) was needed for realizing an improved safety performance (e.g., 11% in peak lateral error). Full automation removed the need for any human control activity and improved safety performance (e.g., 35% in peak lateral error) but put the human in a supervisory position. Haptic shared control kept the driver in the loop, with enhanced performance at reduced control activity, mitigating the known issues that plague full automation. Haptic support for vehicular control ultimately seeks to intuitively combine human intelligence and creativity with the benefits of automation systems.

Manual control of unstable systems

NASA Technical Reports Server (NTRS)

Allen, R. W.; Hogue, J. R.; Parseghian, Z.

1986-01-01

Under certain operational regimes and failure modes, air and ground vehicles can present the human operator with a dynamically unstable or divergent control task. Research conducted over the last two decades has explored the ability of the human operator to control unstable systems under a variety of circumstances. Past research is reviewed and human operator control capabilities are summarized. A current example of automobile directional control under rear brake lockup conditions is also reviewed. A control system model analysis of the driver's steering control task is summarized, based on a generic driver/vehicle model presented at last year's Annual Manual. Results from closed course braking tests are presented that confirm the difficulty the average driver has in controlling the unstable directional dynamics arising from rear wheel lockup.

Automated manual transmission clutch controller

DOEpatents

Lawrie, Robert E.; Reed, Jr., Richard G.; Rausen, David J.

1999-11-30

A powertrain system for a hybrid vehicle. The hybrid vehicle includes a heat engine, such as a diesel engine, and an electric machine, which operates as both an electric motor and an alternator, to power the vehicle. The hybrid vehicle also includes a manual-style transmission configured to operate as an automatic transmission from the perspective of the driver. The engine and the electric machine drive an input shaft which in turn drives an output shaft of the transmission. In addition to driving the transmission, the electric machine regulates the speed of the input shaft in order to synchronize the input shaft during either an upshift or downshift of the transmission by either decreasing or increasing the speed of the input shaft. When decreasing the speed of the input shaft, the electric motor functions as an alternator to produce electrical energy which may be stored by a storage device. Operation of the transmission is controlled by a transmission controller which receives input signals and generates output signals to control shift and clutch motors to effect smooth launch, upshift shifts, and downshifts of the transmission, so that the transmission functions substantially as an automatic transmission from the perspective of the driver, while internally substantially functioning as a manual transmission.

Manual versus Automated Carotid Artery Plaque Component Segmentation in High and Lower Quality 3.0 Tesla MRI Scans

PubMed Central

Smits, Loek P.; van Wijk, Diederik F.; Duivenvoorden, Raphael; Xu, Dongxiang; Yuan, Chun; Stroes, Erik S.; Nederveen, Aart J.

2016-01-01

Purpose To study the interscan reproducibility of manual versus automated segmentation of carotid artery plaque components, and the agreement between both methods, in high and lower quality MRI scans. Methods 24 patients with 30–70% carotid artery stenosis were planned for 3T carotid MRI, followed by a rescan within 1 month. A multicontrast protocol (T1w,T2w, PDw and TOF sequences) was used. After co-registration and delineation of the lumen and outer wall, segmentation of plaque components (lipid-rich necrotic cores (LRNC) and calcifications) was performed both manually and automated. Scan quality was assessed using a visual quality scale. Results Agreement for the detection of LRNC (Cohen’s kappa (k) is 0.04) and calcification (k = 0.41) between both manual and automated segmentation methods was poor. In the high-quality scans (visual quality score ≥ 3), the agreement between manual and automated segmentation increased to k = 0.55 and k = 0.58 for, respectively, the detection of LRNC and calcification larger than 1 mm2. Both manual and automated analysis showed good interscan reproducibility for the quantification of LRNC (intraclass correlation coefficient (ICC) of 0.94 and 0.80 respectively) and calcified plaque area (ICC of 0.95 and 0.77, respectively). Conclusion Agreement between manual and automated segmentation of LRNC and calcifications was poor, despite a good interscan reproducibility of both methods. The agreement between both methods increased to moderate in high quality scans. These findings indicate that image quality is a critical determinant of the performance of both manual and automated segmentation of carotid artery plaque components. PMID:27930665

First step in managing bulimia nervosa: controlled trial of therapeutic manual.

PubMed Central

Treasure, J.; Schmidt, U.; Troop, N.; Tiller, J.; Todd, G.; Keilen, M.; Dodge, E.

1994-01-01

OBJECTIVE--To test the short term efficacy of a self directed treatment manual for bulimia nervosa. DESIGN--Randomised controlled trial of the manual against cognitive behavioural therapy and a waiting list. SETTING--Tertiary referral centre. SUBJECTS--81 consecutive referrals presenting with bulimia nervosa or atypical bulimia nervosa. MAIN OUTCOME MEASURES--Frequency of binge eating, vomiting, and other behaviours to control weight as well as abstinence from these behaviours. RESULTS--Cognitive behavioural treatment produced a significant reduction in the frequency of binge eating, vomiting, and other behaviours to control weight. The manual significantly reduced frequency of binge eating and weight control behaviours other than vomiting, and there was no change in the group on the waiting list. Full remission was achieved in five (24%) of the group assigned to cognitive behavioural treatment, nine (22%) of the group who used the manual, and two (11%) of the group on the waiting list. CONCLUSIONS--A self directed treatment manual may be a useful first intervention in the treatment of bulimia nervosa. PMID:8142791

Review of manual control methods for handheld maneuverable instruments.

PubMed

Fan, Chunman; Dodou, Dimitra; Breedveld, Paul

2013-06-01

By the introduction of new technologies, surgical procedures have been varying from free access in open surgery towards limited access in minimal access surgery. Improving access to difficult-to-reach anatomic sites, e.g. in neurosurgery or percutaneous interventions, needs advanced maneuverable instrumentation. Advances in maneuverable technology require the development of dedicated methods enabling surgeons to stay in direct, manual control of these complex instruments. This article gives an overview of the state-of-the-art in the development of manual control methods for handheld maneuverable instruments. It categorizes the manual control methods in three levels: a) number of steerable segments, b) number of Degrees Of Freedom (DOF), and c) coupling between control motion of the handle and steering motion of the tip. The literature research was completed by using Web of Science, Scopus and PubMed. The study shows that in controlling single steerable segments, direct as well as indirect control methods have been developed, whereas in controlling multiple steerable segments, a gradual shift can be noticed from parallel and serial control to integrated control. The development of multi-segmented maneuverable instruments is still at an early stage, and an intuitive and effective method to control them has to become a primary focus in the domain of minimal access surgery.

Automation effects in a stereotypical multiloop manual control system. [for aircraft

NASA Technical Reports Server (NTRS)

Hess, R. A.; Mcnally, B. D.

1984-01-01

The increasing reliance of state-of-the art, high performance aircraft on high authority stability and command augmentation systems, in order to obtain satisfactory performance and handling qualities, has made critical the achievement of a better understanding of human capabilities, limitations, and preferences during interactions with complex dynamic systems that involve task allocation between man and machine. An analytical and experimental study has been undertaken to investigate human interaction with a simple, multiloop dynamic system in which human activity was systematically varied by changing the levels of automation. Task definition has led to a control loop structure which parallels that for any multiloop manual control system, and may therefore be considered a stereotype.

Speech recognition in advanced rotorcraft - Using speech controls to reduce manual control overload

NASA Technical Reports Server (NTRS)

Vidulich, Michael A.; Bortolussi, Michael R.

1988-01-01

An experiment has been conducted to ascertain the usefulness of helicopter pilot speech controls and their effect on time-sharing performance, under the impetus of multiple-resource theories of attention which predict that time-sharing should be more efficient with mixed manual and speech controls than with all-manual ones. The test simulation involved an advanced, single-pilot scout/attack helicopter. Performance and subjective workload levels obtained supported the claimed utility of speech recognition-based controls; specifically, time-sharing performance was improved while preparing a data-burst transmission of information during helicopter hover.

Process Design Manual for Nitrogen Control.

ERIC Educational Resources Information Center

Parker, Denny S.; And Others

This manual presents theoretical and process design criteria for the implementation of nitrogen control technology in municipal wastewater treatment facilities. Design concepts are emphasized through examination of data from full-scale and pilot installations. Design data are included on biological nitrification and denitrification, breakpoint…

Termite Pest Control - Industrial. Manual 96.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Agricultural Experiment Station.

This training manual provides information needed to meet the minimum EPA standards for certification as a commercial applicator of pesticides in the termite pest control category. The text discusses general pests, especially ants, and wood-destroying organisms such as termites, beetles, and fungi. (CS)

Public Health Pest Control Category Manual.

ERIC Educational Resources Information Center

Bowman, James S.; Turmel, Jon P.

This manual provides information needed to meet the standards for pesticide applicator certification. It presents pest control guidelines for those organisms of public health significance. Fact sheets with line drawings discuss pests such as cockroaches, bedbugs, lice, ants, beetles, bats, birds, and rodents. (CS)

18 CFR 410.1 - Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations. 410.1 Section 410.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS; WATER CODE AND ADMINISTRATIVE MANUAL-PART III...

18 CFR 410.1 - Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 18 Conservation of Power and Water Resources 2 2014-04-01 2014-04-01 false Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations. 410.1 Section 410.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS; WATER CODE AND ADMINISTRATIVE MANUAL-PART III...

18 CFR 410.1 - Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 18 Conservation of Power and Water Resources 2 2013-04-01 2012-04-01 true Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations. 410.1 Section 410.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS; WATER CODE AND ADMINISTRATIVE MANUAL-PART III...

18 CFR 410.1 - Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 2 2012-04-01 2012-04-01 false Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations. 410.1 Section 410.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS; WATER CODE AND ADMINISTRATIVE MANUAL-PART III...

Speech versus manual control of camera functions during a telerobotic task

NASA Technical Reports Server (NTRS)

Bierschwale, John M.; Sampaio, Carlos E.; Stuart, Mark A.; Smith, Randy L.

1989-01-01

Voice input for control of camera functions was investigated in this study. Objective were to (1) assess the feasibility of a voice-commanded camera control system, and (2) identify factors that differ between voice and manual control of camera functions. Subjects participated in a remote manipulation task that required extensive camera-aided viewing. Each subject was exposed to two conditions, voice and manual input, with a counterbalanced administration order. Voice input was found to be significantly slower than manual input for this task. However, in terms of remote manipulator performance errors and subject preference, there was no difference between modalities. Voice control of continuous camera functions is not recommended. It is believed that the use of voice input for discrete functions, such as multiplexing or camera switching, could aid performance. Hybrid mixes of voice and manual input may provide the best use of both modalities. This report contributes to a better understanding of the issues that affect the design of an efficient human/telerobot interface.

Agricultural Plant Pest Control. Manual 93.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Agricultural Experiment Station.

This training manual provides information needed to meet the minimum EPA standards for certification as a commercial applicator of pesticides for the agricultural plant pest control category. The text discusses the insect pests including caterpillars, beetles, and soil inhabiting insects; diseases and nematodes; and weeds. Consideration is given…

Training Manual for Elements of Interface Definition and Control

NASA Technical Reports Server (NTRS)

Lalli, Vincent R. (Editor); Kastner, Robert E. (Editor); Hartt, Henry N. (Editor)

1997-01-01

The primary thrust of this manual is to ensure that the format and information needed to control interfaces between equipment are clear and understandable. The emphasis is on controlling the engineering design of the interface and not on the functional performance requirements of the system or the internal workings of the interfacing equipment. Interface control should take place, with rare exception, at the interfacing elements and no further. There are two essential sections of the manual. Chapter 2, Principles of Interface Control, discusses how interfaces are defined. It describes different types of interfaces to be considered and recommends a format for the documentation necessary for adequate interface control. Chapter 3, The Process: Through the Design Phases, provides tailored guidance for interface definition and control. This manual can be used to improve planned or existing interface control processes during system design and development. It can also be used to refresh and update the corporate knowledge base. The information presented herein will reduce the amount of paper and data required in interface definition and control processes by as much as 50 percent and will shorten the time required to prepare an interface control document. It also highlights the essential technical parameters that ensure that flight subsystems will indeed fit together and function as intended after assembly and checkout.

Effects of Retinal Eccentricity on Human Manual Control

NASA Technical Reports Server (NTRS)

Popovici, Alexandru; Zaal, Peter M. T.

2017-01-01

This study investigated the effects of viewing a primary flight display at different retinal eccentricities on human manual control behavior and performance. Ten participants performed a pitch tracking task while looking at a simplified primary flight display at different horizontal and vertical retinal eccentricities, and with two different controlled dynamics. Tracking performance declined at higher eccentricity angles and participants behaved more nonlinearly. The visual error rate gain increased with eccentricity for single-integrator-like controlled dynamics, but decreased for double-integrator-like dynamics. Participants' visual time delay was up to 100 ms higher at the highest horizontal eccentricity compared to foveal viewing. Overall, vertical eccentricity had a larger impact than horizontal eccentricity on most of the human manual control parameters and performance. Results might be useful in the design of displays and procedures for critical flight conditions such as in an aerodynamic stall.

General Pest Control - Industrial. Manual 95.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Agricultural Experiment Station.

This training manual provides information needed to meet the minimum EPA standards for certification as a commercial applicator of pesticides in the general pest control category. The text discusses general, parasitic and miscellaneous pests such as ants, ticks, and spiders; fabric, wood-destroying, and grain pests such as beetles, termites, and…

Implementation and control of a 3 degree-of-freedom, force-reflecting manual controller

NASA Astrophysics Data System (ADS)

Kim, Whee-Kuk; Bevill, Pat; Tesar, Delbert

1991-02-01

Most available manual controllers which are used in bilateral or force-reflecting teleoperator systems can be characterized by their bulky size heavy weight high cost low magnitude of reflecting-force lack of smoothness insufficient transparency and simplified architectures. A compact smooth lightweight portable universal manual controller could provide a markedly improved level of transparency and be able to drive a broad spectrum of slave manipulators. This implies that a single stand-off position could be used for a diverse population of remote systems and that a standard environment for training of operators would result in reduced costs and higher reliability. In the implementation presented in this paper a parallel 3 degree-of-freedom (DOF) spherical structure (for compactness and reduced weight) is combined with high gear-ratio reducers using a force control algorithm to produce a " power steering" effect for enhanced smoothness and transparency. The force control algorithm has the further benefit of minimizing the effect of the system friction and non-linear inertia forces. The fundamental analytical description for the spherical force-reflecting manual controller such as forward position analysis reflecting-force transformation and applied force control algorithm are presented. Also a brief description of the system integration its actual implementation and preliminary test results are presented in the paper.

Water Quality & Pollutant Source Monitoring: Field and Laboratory Procedures. Training Manual.

ERIC Educational Resources Information Center

Office of Water Program Operations (EPA), Cincinnati, OH. National Training and Operational Technology Center.

This training manual presents material on techniques and instrumentation used to develop data in field monitoring programs and related laboratory operations concerned with water quality and pollution monitoring. Topics include: collection and handling of samples; bacteriological, biological, and chemical field and laboratory methods; field…

Architectural study of the design and operation of advanced force feedback manual controllers

NASA Technical Reports Server (NTRS)

Tesar, Delbert; Kim, Whee-Kuk

1990-01-01

A teleoperator system consists of a manual controller, control hardware/software, and a remote manipulator. It was employed in either hazardous or unstructured, and/or remote environments. In teleoperation, the main-in-the-loop is the central concept that brings human intelligence to the teleoperator system. When teleoperation involves contact with an uncertain environment, providing the feeling of telepresence to the human operator is one of desired characteristics of the teleoperator system. Unfortunately, most available manual controllers in bilateral or force-reflecting teleoperator systems can be characterized by their bulky size, high costs, or lack of smoothness and transparency, and elementary architectures. To investigate other alternatives, a force-reflecting, 3 degree of freedom (dof) spherical manual controller is designed, analyzed, and implemented as a test bed demonstration in this research effort. To achieve an improved level of design to meet criteria such as compactness, portability, and a somewhat enhanced force-reflecting capability, the demonstration manual controller employs high gear-ratio reducers. To reduce the effects of the inertia and friction on the system, various force control strategies are applied and their performance investigated. The spherical manual controller uses a parallel geometry to minimize inertial and gravitational effects on its primary task of transparent information transfer. As an alternative to the spherical 3-dof manual controller, a new conceptual (or parallel) spherical 3-dof module is introduced with a full kinematic analysis. Also, the resulting kinematic properties are compared to those of other typical spherical 3-dof systems. The conceptual design of a parallel 6-dof manual controller and its kinematic analysis is presented. This 6-dof manual controller is similar to the Stewart Platform with the actuators located on the base to minimize the dynamic effects. Finally, a combination of the new 3-dof and 6-dof

Automated manual transmission shift sequence controller

DOEpatents

Lawrie, Robert E.; Reed, Richard G.; Rausen, David J.

2000-02-01

A powertrain system for a hybrid vehicle. The hybrid vehicle includes a heat engine, such as a diesel engine, and an electric machine, which operates as both, an electric motor and an alternator, to power the vehicle. The hybrid vehicle also includes a manual-style transmission configured to operate as an automatic transmission from the perspective of the driver. The engine and the electric machine drive an input shaft which in turn drives an output shaft of the transmission. In addition to driving the transmission, the electric machine regulates the speed of the input shaft in order to synchronize the input shaft during either an upshift or downshift of the transmission by either decreasing or increasing the speed of the input shaft. When decreasing the speed of the input shaft, the electric motor functions as an alternator to produce electrical energy which may be stored by a storage device. Operation of the transmission is controlled by a transmission controller which receives input signals and generates output signals to control shift and clutch motors to effect smooth launch, upshift shifts, and downshifts of the transmission, so that the transmission functions substantially as an automatic transmission from the perspective of the driver, while internally substantially functioning as a manual transmission.

Automated manual transmission mode selection controller

DOEpatents

Lawrie, Robert E.

1999-11-09

A powertrain system for a hybrid vehicle. The hybrid vehicle includes a heat engine, such as a diesel engine, and an electric machine, which operates as both an electric motor and an alternator, to power the vehicle. The hybrid vehicle also includes a manual-style transmission configured to operate as an automatic transmission from the perspective of the driver. The engine and the electric machine drive an input shaft which in turn drives an output shaft of the transmission. In addition to driving the transmission, the electric machine regulates the speed of the input shaft in order to synchronize the input shaft during either an upshift or downshift of the transmission by either decreasing or increasing the speed of the input shaft. When decreasing the speed of the input shaft, the electric motor functions as an alternator to produce electrical energy which may be stored by a storage device. Operation of the transmission is controlled by a transmission controller which receives input signals and generates output signals to control shift and clutch motors to effect smooth launch, upshift shifts, and downshifts of the transmission, so that the transmission functions substantially as an automatic transmission from the perspective of the driver, while internally substantially functioning as a manual transmission.

Speech versus manual control of camera functions during a telerobotic task

NASA Technical Reports Server (NTRS)

Bierschwale, John M.; Sampaio, Carlos E.; Stuart, Mark A.; Smith, Randy L.

1993-01-01

This investigation has evaluated the voice-commanded camera control concept. For this particular task, total voice control of continuous and discrete camera functions was significantly slower than manual control. There was no significant difference between voice and manual input for several types of errors. There was not a clear trend in subjective preference of camera command input modality. Task performance, in terms of both accuracy and speed, was very similar across both levels of experience.

Manual, mechanical, and cultural control methds and tools

Treesearch

Steven Manning; James Miller

2011-01-01

There are many land management scenarios where chemicals are not the ideal choice for controlling invasive plants. More often than not, the best approach is the use of integrated pest management involving a variety of control methods. Maximizing the value of mechanical, manual, and cultural control methods with the added benefit of selective herbicides can offer the...

Automation effects in a multiloop manual control system

NASA Technical Reports Server (NTRS)

Hess, R. A.; Mcnally, B. D.

1986-01-01

An experimental and analytical study was undertaken to investigate human interaction with a simple multiloop manual control system in which the human's activity was systematically varied by changing the level of automation. The system simulated was the longitudinal dynamics of a hovering helicopter. The automation-systems-stabilized vehicle responses from attitude to velocity to position and also provided for display automation in the form of a flight director. The control-loop structure resulting from the task definition can be considered a simple stereotype of a hierarchical control system. The experimental study was complemented by an analytical modeling effort which utilized simple crossover models of the human operator. It was shown that such models can be extended to the description of multiloop tasks involving preview and precognitive human operator behavior. The existence of time optimal manual control behavior was established for these tasks and the role which internal models may play in establishing human-machine performance was discussed.

Manual Therapy for Hip Osteoarthritis: A Systematic Review and Meta-analysis.

PubMed

Wang, Qiong; Wang, Teng-teng; Qi, Xiao-feng; Yao, Min; Cui, Xue-jun; Wang, Yong-jun; Liang, Qian-qian

2015-11-01

Hip osteoarthritis (HOA) is one of the major causes of disability in seniors and is costly to society. Manual therapy is one therapeutic approach to treating HOA. To assess the effect of manual therapy compared to the placebo or wait-list/no treatment or a minimal intervention control for HOA at post-treatment and short-, intermediate- and long-term follow-ups. A systematic review and meta-analysis of randomized controlled trials (RCTs). Hospital outpatient clinic in China. We searched PubMed, EMBASE, the Cochrane Library, CINAHL, ISI web of knowledge, and Chinese databases from the inception to October 2014 without language restrictions. References of systematic reviews and other related reviews, files in our department, and conference proceedings as grey literature were also screened by hand. RCTs compared manual therapy to the placebo, wait-list/no treatment or a minimal intervention control with an appropriate and precise description of randomization. Two reviewers independently conducted the search results identification, data extraction, and methodological quality assessment. We calculated the risk difference (RD) for dichotomous data and the mean difference (MD) or standardized mean difference (SMD) for continuous data in a fixed or random effect model. The primary outcomes were self-reported pain in the past week and physical function. The secondary outcomes were the quality of life, global perceived effect, patients' satisfaction, cost, and adverse events. Six studies involving 515 HOA patients were included. Five of the 6 studies ranked as high quality in the methodological assessment. Immediately post-treatment, there was low-quality evidence that manual therapy could not statistically significantly relieve pain (SMD: -0.07 [95%CI -0.38 to 0.24]); for physical function, a moderate quality of evidence showed that manual therapy could not improve the physical function significantly (SMD: 0.14 [95%CI -0.08 to 0.37]). We still found low-quality evidence that

Nevada National Security Site Radiological Control Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Radiological Control Managers’ Council

2012-03-26

This document supersedes DOE/NV/25946--801, 'Nevada Test Site Radiological Control Manual,' Revision 1 issued in February 2010. Brief Description of Revision: A complete revision to reflect a recent change in name for the NTS; changes in name for some tenant organizations; and to update references to current DOE policies, orders, and guidance documents. Article 237.2 was deleted. Appendix 3B was updated. Article 411.2 was modified. Article 422 was re-written to reflect the wording of DOE O 458.1. Article 431.6.d was modified. The glossary was updated. This manual contains the radiological control requirements to be used for all radiological activities conducted bymore » programs under the purview of the U.S. Department of Energy (DOE) and the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO). Compliance with these requirements will ensure compliance with Title 10 Code of Federal Regulations (CFR) Part 835, 'Occupational Radiation Protection.' Programs covered by this manual are located at the Nevada National Security Site (NNSS); Nellis Air Force Base and North Las Vegas, Nevada; Santa Barbara and Livermore, California; and Andrews Air Force Base, Maryland. In addition, fieldwork by NNSA/NSO at other locations is covered by this manual. Current activities at NNSS include operating low-level radioactive and mixed waste disposal facilities for United States defense-generated waste, assembly and execution of subcritical experiments, assembly/disassembly of special experiments, the storage and use of special nuclear materials, performing criticality experiments, emergency responder training, surface cleanup and site characterization of contaminated land areas, environmental activity by the University system, and nonnuclear test operations, such as controlled spills of hazardous materials at the Hazardous Materials Spill Center. Currently, the major potential for occupational radiation exposure is associated with the

Anaerobic Digestion. Student Manual. Biological Treatment Process Control.

ERIC Educational Resources Information Center

Carnegie, John W., Ed.

This student manual contains the textual material for a four-lesson unit on anaerobic digestion control. Areas addressed include: (1) anaerobic sludge digestion (considering the nature of raw sludge, purposes of anaerobic digestion, the results of digestion, types of equipment, and other topics); (2) digester process control (considering feeding…

Real-time control of combined surface water quantity and quality: polder flushing.

PubMed

Xu, M; van Overloop, P J; van de Giesen, N C; Stelling, G S

2010-01-01

In open water systems, keeping both water depths and water quality at specified values is critical for maintaining a 'healthy' water system. Many systems still require manual operation, at least for water quality management. When applying real-time control, both quantity and quality standards need to be met. In this paper, an artificial polder flushing case is studied. Model Predictive Control (MPC) is developed to control the system. In addition to MPC, a 'forward estimation' procedure is used to acquire water quality predictions for the simplified model used in MPC optimization. In order to illustrate the advantages of MPC, classical control [Proportional-Integral control (PI)] has been developed for comparison in the test case. The results show that both algorithms are able to control the polder flushing process, but MPC is more efficient in functionality and control flexibility.

The effects of voice and manual control mode on dual task performance

NASA Technical Reports Server (NTRS)

Wickens, C. D.; Zenyuh, J.; Culp, V.; Marshak, W.

1986-01-01

Two fundamental principles of human performance, compatibility and resource competition, are combined with two structural dichotomies in the human information processing system, manual versus voice output, and left versus right cerebral hemisphere, in order to predict the optimum combination of voice and manual control with either hand, for time-sharing performance of a dicrete and continuous task. Eight right handed male subjected performed a discrete first-order tracking task, time-shared with an auditorily presented Sternberg Memory Search Task. Each task could be controlled by voice, or by the left or right hand, in all possible combinations except for a dual voice mode. When performance was analyzed in terms of a dual-task decrement from single task control conditions, the following variables influenced time-sharing efficiency in diminishing order of magnitude, (1) the modality of control, (discrete manual control of tracking was superior to discrete voice control of tracking and the converse was true with the memory search task), (2) response competition, (performance was degraded when both tasks were responded manually), (3) hemispheric competition, (performance degraded whenever two tasks were controlled by the left hemisphere) (i.e., voice or right handed control). The results confirm the value of predictive models invoice control implementation.

Cost Control. Michigan School Food Service Training Manual.

ERIC Educational Resources Information Center

Michigan State Univ., East Lansing. Cooperative Extension Service.

Cost control is the subject of this eight-lesson, three-test food service training manual. Lesson 1 deals with financial accountability and includes 17 handouts, ranging from sample balance to quarterly report sheets. Lesson 2 focuses on budgeting principles, and lesson 3 on labor controls. Professional purchasing, receiving, and inventorying…

The CERCA School Report Card: Communities Creating Education Quality. Implementation Manual

ERIC Educational Resources Information Center

Guio, Ana Florez; Chesterfield, Ray; Siri, Carmen

2006-01-01

This manual provides a step-by-step methodology for promoting community participation in improving learning in local schools. The Civic Engagement for Education Reform in Central America (CERCA) School Report Card (SRC) approach empowers local school communities to gather information on the quality and conditions of teaching and learning in their…

77 FR 28455 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-14

... Options for design and applications of traffic control devices, this Manual should not be considered a... application of traffic control devices, as well as in the location and design of roads and streets that the..., while this Manual provides Standards, Guidance, and Options for design and applications of traffic...

18 CFR 410.1 - Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 2 2011-04-01 2011-04-01 false Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations. 410.1 Section 410.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS; WATER...

Multiloop Manual Control of Dynamic Systems

NASA Technical Reports Server (NTRS)

Hess, R. A.; Mcnally, B. D.

1984-01-01

Human interaction with a simple, multiloop dynamic system in which the human's activity was systematically varied by changing the levels of automation was studied. The control loop structure resulting from the task definition parallels that for any multiloop manual control system, is considered a sterotype. Simple models of the human in the task, and upon extending a technique for describing the manner in which the human subjectively quantifies his opinion of task difficulty were developed. A man in the loop simulation which provides data to support and direct the analytical effort is presented.

Right Of Way Pest Control. Manual 88.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Agricultural Experiment Station.

This training manual provides information needed to meet the minimum EPA standards for certification as a commercial applicator of pesticides in the right-of-way pest control category. The text discusses types of vegetation, the nature of herbicides, application methods, use for specific situations, and safety precautions. (CS)

Six degree of freedom manual controls study report

NASA Technical Reports Server (NTRS)

Mckinnon, G. M.; Lippay, A.; King, M. L.

1982-01-01

The feasibility of using degree of freedom manual controls in space in an on orbit environment was determined. Several six degree of freedom controls were tested in a laboratory environment, and replica controls were used to control robot arms. The selection of six degrees of freedom as a design goal was based on the fact that six degrees are sufficient to define the location and orientation of a rigid body in space.

Safe, Effective Use of Pesticides, A Manual for Commercial Applicators: Aquatic Pest Control.

ERIC Educational Resources Information Center

Extension Service (USDA), Washington, DC.

This manual is intended to assist pesticide applicators in the area of aquatic pest control meet the requirements of the Michigan Department of Agriculture for certification. The Environmental Protection Agency (EPA) Aquatic Pest Control Guide served as a basis for this manual. The six sections presented describe: (1) Aquatic pest control; (2)…

Applicator Training Manual for: Public Health Pest Control.

ERIC Educational Resources Information Center

Moore, E. E.

This manual gives the life cycle and habitats, public health importance, methods of non-chemical control, and pesticides and methods of application for mosquitoes, flies, bedbugs, fleas, lice, cockroaches, venomous anthropods, ticks and chiggers, and rodents. (BB)

Effects of an exercise and manual therapy program on physical impairments, function and quality-of-life in people with osteoporotic vertebral fracture: a randomised, single-blind controlled pilot trial

PubMed Central

2010-01-01

Background This randomised, single-blind controlled pilot trial aimed to determine the effectiveness of a physiotherapy program, including exercise and manual therapy, in reducing impairments and improving physical function and health-related quality of life in people with a history of painful osteoporotic vertebral fracture. Methods 20 participants were randomly allocated to an intervention (n = 11) or control (n = 9) group. The intervention group attended individual sessions with an experienced clinician once a week for 10 weeks and performed daily home exercises with adherence monitored by a self-report diary. The control group received no treatment. Blinded assessment was conducted at baseline and 11 weeks. Questionnaires assessed self-reported changes in back pain, physical function, and health-related quality of life. Objective measures of thoracic kyphosis, back and shoulder muscle endurance (Timed Loaded Standing Test), and function (Timed Up and Go test) were also taken. Results Compared with the control group, the intervention group showed significant reductions in pain during movement (mean difference (95% CI) -1.8 (-3.5 to -0.1)) and at rest (-2.0 (-3.8 to -0.2)) and significantly greater improvements in Qualeffo physical function (-4.8 (-9.2 to -0.5)) and the Timed Loaded Standing test (46.7 (16.1 to 77.3) secs). For the perceived change in back pain over the 10 weeks, 9/11 (82%) participants in the intervention group rated their pain as 'much better' compared with only 1/9 (11%) participants in the control group. Conclusion Despite the modest sample size, these results support the benefits of exercise and manual therapy in the clinical management of patients with osteoporotic vertebral fractures, but need to be confirmed in a larger sample. Trail registration NCT00638768 PMID:20163739

A Corrosion Control Manual for Rail Rapid Transit

NASA Technical Reports Server (NTRS)

Gilbert, L. O.; Fitzgerald, J. H., III; Menke, J. T.; Lizak, R. M. (Editor)

1982-01-01

This manual addresses corrosion problems in the design, contruction, and maintenance of rapid transit systems. Design and maintenance solutions are provided for each problem covered. The scope encompasses all facilities of urban rapid transit systems: structures and tracks, platforms and stations, power and signals, and cars. The types of corrosion and their causes as well as rapid transit properties are described. Corrosion control committees, and NASA, DOD, and ASTM specifications and design criteria to which reference is made in the manual are listed. A bibliography of papers and excerpts of reports is provided and a glossary of frequently used terms is included.

Control Requirements to Support Manual Piloting Capability

NASA Technical Reports Server (NTRS)

Merancy, Nujoud; Chevray, Kay; Gonzalez, Rodolfo; Madsen, Jennifer; Spehar, Pete

2013-01-01

The manual piloting requirements specified under the NASA Constellation Program involved Cooper-Harper ratings, which are a qualitative and subjective evaluation from experienced pilots. This type of verification entails a significant investment of resources to assess a completed design and is not one that can easily or meaningfully be applied upfront in the design phase. The evolution of the Multi-Purpose Crew Vehicle Program to include an independently developed propulsion system from an international partner makes application of Cooper-Harper based design requirements inadequate. To mitigate this issue, a novel solution was developed to reformulate the necessary piloting capability into quantifiable requirements. A trio of requirements was designed which specify control authority, precision, and impulse residuals enabling propulsion design within specified guidance and control boundaries. These requirements have been evaluated against both the existing Orion design and the proposed ESA design and have been found to achieve the desired specificity. The requirement set is capable of being applied to the development of other spacecraft in support of manual piloting.

Manual and automatic flight control during severe turbulence penetration

NASA Technical Reports Server (NTRS)

Johnston, D. E.; Klein, R. H.; Hoh, R. H.

1976-01-01

An analytical and experimental investigation of possible contributing factors in jet aircraft turbulence upsets was conducted. Major contributing factors identified included autopilot and display deficiencies, the large aircraft inertia and associated long response time, and excessive pilot workload. An integrated flight and thrust energy management director system was synthesized. The system was incorporated in a moving-base simulation and evaluated using highly experienced airline pilots. The evaluation included comparison of pilot workload and flight performance during severe turbulence penetration utilizing four control/display concepts: manual control with conventional full panel display, conventional autopilot (A/P-A) with conventional full panel display, improved autopilot (A/P-B) with conventional full panel display plus thrust director display, and longitudinal flight director with conventional full panel display plus thrust director display. Simulation results show improved performance, reduced pilot workload, and a pilot preference for the autopilot system controlling to the flight director command and manual control of thrust following the trim thrust director.

IMAT graphics manual

NASA Technical Reports Server (NTRS)

Stockwell, Alan E.; Cooper, Paul A.

1991-01-01

The Integrated Multidisciplinary Analysis Tool (IMAT) consists of a menu driven executive system coupled with a relational database which links commercial structures, structural dynamics and control codes. The IMAT graphics system, a key element of the software, provides a common interface for storing, retrieving, and displaying graphical information. The IMAT Graphics Manual shows users of commercial analysis codes (MATRIXx, MSC/NASTRAN and I-DEAS) how to use the IMAT graphics system to obtain high quality graphical output using familiar plotting procedures. The manual explains the key features of the IMAT graphics system, illustrates their use with simple step-by-step examples, and provides a reference for users who wish to take advantage of the flexibility of the software to customize their own applications.

A randomized controlled trial of the effects of muscle stretching, manual therapy and steroid injections in addition to 'stay active' care on health-related quality of life in acute or subacute low back pain.

PubMed

Grunnesjö, Marie I; Bogefeldt, Johan P; Blomberg, Stefan I E; Strender, Lars-Erik; Svärdsudd, Kurt F

2011-11-01

To evaluate the health-related quality of life effects of muscle stretching, manual therapy and steroid injections in addition to 'stay active' care in acute or subacute low back pain patients. A randomized, controlled trial during 10 weeks with four treatment groups. Nine primary health care and one outpatient orthopaedic hospital department. One hundred and sixty patients with acute or subacute low back pain. Ten weeks of 'stay active' care only (group 1), or 'stay active' and muscle stretching (group 2), or 'stay active', muscle stretching and manual therapy (group 3), or 'stay active', muscle stretching, manual therapy and steroid injections (group 4). The Gothenburg Quality of Life instrument subscales Well-being score and Complaint score. In a multivariate analysis adjusted for possible outcome affecting variables other than the treatment given Well-being score was 68.4 (12.5), 72.1 (12.4), 72,3 (12.4) and 72.7 (12.5) in groups 1-4, respectively (P for trend <0.05). There were significant trends for the well-being components patience (P < 0.005), energy (P < 0.05), mood (P < 0.05) and family situation (P < 0.05). The remaining two components and Complaint score showed a non-significant trend towards improvement. The effects on health-related quality of life were greater the larger the number of treatment modalities available. The 'stay active' treatment group, with the most restricted number of modalities, had the most modest health-related quality of life improvement, while group 4 with the most generous choice of treatment modalities, had the greatest improvement.

Moderate quality evidence finds statistical benefit in oral health for powered over manual toothbrushes.

PubMed

Niederman, Richard

2014-09-01

The Cochrane Oral Health Group's Trials Register, the Cochrane Central Register of Controlled Trials (CENTRAL), Medline, Embase, CINAHL, National Institutes of Health Trials Register and the WHO Clinical Trials Registry Platform for ongoing trials. Reference lists of identified articles were also scanned for relevant papers. Identified manufacturers were contacted for additional information. Only randomised controlled trials comparing manual and powered toothbrushes were considered. Crossover trials were eligible for inclusion if the wash-out period length was more than two weeks. Study assessment and data extraction were carried out independently by at least two reviewers. The primary outcome measures were quantified levels of plaque or gingivitis. Risk of bias assessment was undertaken. Standard Cochrane methodological approaches were taken. Random-effects models were used provided there were four or more studies included in the meta-analysis, otherwise fixed-effect models were used. Data were classed as short term (one to three months) and long term (greater than three months). Fifty-six trials were included with 51 (4624 patients) providing data for meta-analysis. The majority (46) were at unclear risk of bias, five at high risk of bias and five at low risk. There was moderate quality evidence that powered toothbrushes provide a statistically significant benefit compared with manual toothbrushes with regard to the reduction of plaque in both the short and long-term. This corresponds to an 11% reduction in plaque for the Quigley Hein index (Turesky) in the short term and a 21% reduction in the long term. There was a high degree of heterogeneity that was not explained by the different powered toothbrush type subgroups.There was also moderate quality evidence that powered toothbrushes again provide a statistically significant reduction in gingivitis when compared with manual toothbrushes both in the short and long term. This corresponds to a 6% and 11% reduction

Ohio manual of uniform traffic control devices [2003

DOT National Transportation Integrated Search

2003-01-01

The purpose of traffic control device and warrants for their use is to help to insure highway safety by providing for the orderly and predictable movement of all traffic and to provide such guidance and warnings as are needed. This manual sets forth ...

Flight experience with manually controlled unconventional aircraft motions

NASA Technical Reports Server (NTRS)

Barfield, A. F.

1978-01-01

A modified YF-16 aircraft was used to flight demonstrate decoupled modes under the USAF Fighter Control Configured Vehicle (CCV) Program. The direct force capabilities were used to implement seven manually controlled unconventional modes on the aircraft, allowing flat turns, decoupled normal acceleration control, independent longitudinal and lateral translations, uncoupled elevation and azimuth aiming, and blended direct lift. This paper describes the design, development, and flight testing of these control modes. The need for task-tailored mode authorities, gain-scheduling and selected closed-loop design is discussed.

Manual Therapy With Cryotherapy Versus Manual Therapy With Kinesio Taping for Males With Lumbar Discopathy: A Pilot Randomized Trial.

PubMed

Lizis, Pawel; Kobza, Wojciech

2017-06-23

Context • Numerous modalities of therapeutic interventions exist for lumbar discopathy. Manual therapy is one option, although its effectiveness remains controversial. The addition of cryotherapy to manual therapy may enhance the health benefits in patients with lumbar discopathy.  Objective • The study intended to evaluate the efficacy of manual therapy combined with cryotherapy vs manual therapy combined with Kinesio taping for males with lumbar discopathy. Design • The research team designed a pilot randomized trial with concealed allocation, assessor blinding, and intention-to-treat analysis. Setting • The study occurred in the Physiotherapy Outpatient Department of the Regional Hospital (Zywiec, Poland). Participants • The participants were 40 males with lumbar discopathy, aged 30-75 y, who were patients in the department at the hospital. Intervention • The participants were randomly assigned to an intervention group that received Kaltenborn-Evjenth orthopedic manual therapy (KEOMT) combined with cryotherapy, the KEOMT-C group (n = 20), or to a control group that received KEOMT combined with Kinesio taping, the KEOMT-K group (n = 20). The participants in both groups received 10 treatments, 2 per wk for 5 wk. Outcome Measures • The primary outcome was measured using a visual analog scale and the Laitinen scale pain ratings. The secondary outcome measured the quality of life using the short form-36 questionnaire. The participants completed the tests at baseline and postintervention. Results • After the treatments, the intervention group had significantly lower scores than the control group for pain as well as significantly higher scores for quality of life. Conclusions • Patients achieved better health benefits from manual therapy when it was combined with cryotherapy.

Forest Pest Control and Timber Treatment Category Manual.

ERIC Educational Resources Information Center

Bowman, James S.; Turmel, Jon P.

This manual provides information needed to meet the standards for pesticide applicator certification. The document is a compilation of pamphlets and circulars which discuss forest management, control of undesirable woody plants, herbicides in forestry, diseases and insect pests, and equipment for pesticide application. (CS)

Applicator Training Manual for: Agricultural Animal Pest Control.

ERIC Educational Resources Information Center

Christensen, Christian M.

This manual discusses pesticide safety and environmental considerations, pesticide toxicity, residue potential, pesticide formulations, and application techniques. In addition, descriptions of, and methods for controlling insects and related pests that attack cattle, sheep and goats, swine, horses and other equines, and poultry are given. These…

The Identification and Modeling of Visual Cue Usage in Manual Control Task Experiments

NASA Technical Reports Server (NTRS)

Sweet, Barbara Townsend; Trejo, Leonard J. (Technical Monitor)

1999-01-01

Many fields of endeavor require humans to conduct manual control tasks while viewing a perspective scene. Manual control refers to tasks in which continuous, or nearly continuous, control adjustments are required. Examples include flying an aircraft, driving a car, and riding a bicycle. Perspective scenes can arise through natural viewing of the world, simulation of a scene (as in flight simulators), or through imaging devices (such as the cameras on an unmanned aerospace vehicle). Designers frequently have some degree of control over the content and characteristics of a perspective scene; airport designers can choose runway markings, vehicle designers can influence the size and shape of windows, as well as the location of the pilot, and simulator database designers can choose scene complexity and content. Little theoretical framework exists to help designers determine the answers to questions related to perspective scene content. An empirical approach is most commonly used to determine optimum perspective scene configurations. The goal of the research effort described in this dissertation has been to provide a tool for modeling the characteristics of human operators conducting manual control tasks with perspective-scene viewing. This is done for the purpose of providing an algorithmic, as opposed to empirical, method for analyzing the effects of changing perspective scene content for closed-loop manual control tasks.

MFCVs (Manual Flow Control Valves) in the Lab

NASA Image and Video Library

2009-07-07

ISS020-E-017705 (7 July 2009) --- NASA astronaut Michael Barratt, Expedition 20 flight engineer, works at a rotated rack in the Destiny laboratory of the International Space Station during in-flight maintenance (IFM) to adjust the periodic flow rate of manual flow control valves for coolant loops.

MFCVs (Manual Flow Control Valves) in the Lab

NASA Image and Video Library

2009-07-07

ISS020-E-017710 (7 July 2009) --- NASA astronaut Michael Barratt, Expedition 20 flight engineer, works at a rotated rack in the Destiny laboratory of the International Space Station during in-flight maintenance (IFM) to adjust the periodic flow rate of manual flow control valves for coolant loops.

IS MANUAL THERAPY A RATIONAL APPROACH TO IMPROVING HEALTH-RELATED QUALITY OF LIFE IN PEOPLE WITH ARTHRITIS?

PubMed Central

Cameron, Melainie

2002-01-01

Background: People with arthritic disease are advised to participate in gentle exercise on a regular basis, and pursue long-term medication regimes. Alternative therapies are also used by people with arthritis, and may sometimes be recommended by rheumatologists and other medical personnel. Alternative therapies may be divided into two types: active therapies, in which the patient takes a driving role, and passive therapies, in which the therapy cannot proceed unless driven by a therapist. Objective: To review the effectiveness of manual therapy in improving the health-related quality of life (HRQOL) of people with two common arthritis conditions: Osteoarthritis and rheumatoid arthritis. Discussion: Massage, and other passive (practitioner-driven) manual therapies, have been anecdotally reported to improve health-related quality of life (HRQOL) in people with arthritis. Many manual therapists consult with patients who have arthritic diseases, receive referrals from rheumatologists, and consider the arthritic diseases to be within their field of practise. Although there is empirical evidence that manual therapy with some types of arthritis is beneficial, the level of effectiveness however is under-researched. Medical authorities are reluctant to endorse manual therapies for arthritis due to a lack of scientific evidence demonstrating efficacy, safety, and cost effectiveness. PMID:17987169

Facultative Lagoons. Student Manual. Biological Treatment Process Control.

ERIC Educational Resources Information Center

Andersen, Lorri

The textual material for a unit on facultative lagoons is presented in this student manual. Topic areas discussed include: (1) loading; (2) microbial theory; (3) structure and design; (4) process control; (5) lagoon start-up; (6) data handling and analysis; (7) lagoon maintenance (considering visual observations, pond structure, safety, odor,…

Emergency Manuals: How Quality Improvement and Implementation Science Can Enable Better Perioperative Management During Crises.

PubMed

Goldhaber-Fiebert, Sara N; Macrae, Carl

2018-03-01

How can teams manage critical events more effectively? There are commonly gaps in performance during perioperative crises, and emergency manuals are recently available tools that can improve team performance under stress, via multiple mechanisms. This article examines how the principles of implementation science and quality improvement were applied by multiple teams in the development, testing, and systematic implementations of emergency manuals in perioperative care. The core principles of implementation have relevance for future patient safety innovations perioperatively and beyond, and the concepts of emergency manuals and interprofessional teamwork are applicable for diverse fields throughout health care. Copyright © 2017 Sara N. Goldhaber-Fiebert, Carl Macrae. Published by Elsevier Inc. All rights reserved.

[Strategies and development of quality assurance and control in the ELSA-Brasil].

PubMed

Schmidt, Maria Inês; Griep, Rosane Härter; Passos, Valéria Maria; Luft, Vivian Cristine; Goulart, Alessandra Carvalho; Menezes, Greice Maria de Souza; Molina, Maria del Carmen Bisi; Vigo, Alvaro; Nunes, Maria Angélica

2013-06-01

The ELSA-Brasil (Estudo Longitudinal de Saúde do Adulto - Brazilian Longitudinal Study for Adult Health) is a cohort study composed of 15,105 adults followed up in order to assess the development of chronic diseases, especially diabetes and cardiovascular disease. Its size, multicenter nature and the diversity of measurements required effective and efficient mechanisms of quality assurance and control. The main quality assurance activities (those developed before data collection) were: careful selection of research instruments, centralized training and certification, pretesting and pilot studies, and preparation of operation manuals for the procedures. Quality control activities (developed during data collection and processing) were performed more intensively at the beginning, when routines had not been established yet. The main quality control activities were: periodic observation of technicians, test-retest studies, data monitoring, network of supervisors, and cross visits. Data that estimate the reliability of the obtained information attest that the quality goals have been achieved.

Automated quality control in a file-based broadcasting workflow

NASA Astrophysics Data System (ADS)

Zhang, Lina

2014-04-01

Benefit from the development of information and internet technologies, television broadcasting is transforming from inefficient tape-based production and distribution to integrated file-based workflows. However, no matter how many changes have took place, successful broadcasting still depends on the ability to deliver a consistent high quality signal to the audiences. After the transition from tape to file, traditional methods of manual quality control (QC) become inadequate, subjective, and inefficient. Based on China Central Television's full file-based workflow in the new site, this paper introduces an automated quality control test system for accurate detection of hidden troubles in media contents. It discusses the system framework and workflow control when the automated QC is added. It puts forward a QC criterion and brings forth a QC software followed this criterion. It also does some experiments on QC speed by adopting parallel processing and distributed computing. The performance of the test system shows that the adoption of automated QC can make the production effective and efficient, and help the station to achieve a competitive advantage in the media market.

Control technology appendices for pollution control technical manuals. Final report, June 1982-February 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1983-04-01

The document is one of six technical handbooks prepared by EPA to help government officials granting permits to build synfuels facilities, synfuels process developers, and other interested parties. They provide technical data on waste streams from synfuels facilities and technologies capable of controlling them. Process technologies covered in the manuals include coal gasification, coal liquefaction by direct and idirect processing, and the extraction of oil from shale. The manuals offer no regulatory guidance, allowing the industry flexibility in deciding how best to comply with environmental regulations.

Endpoint Accuracy in Manual Control of a Steerable Needle.

PubMed

van de Berg, Nick J; Dankelman, Jenny; van den Dobbelsteen, John J

2017-02-01

To study the ability of a human operator to manually correct for errors in the needle insertion path without partial withdrawal of the needle by means of an active, tip-articulated steerable needle. The needle is composed of a 1.32-mm outer-diameter cannula, with a flexure joint near the tip, and a retractable stylet. The bending stiffness of the needle resembles that of a 20-gauge hypodermic needle. The needle functionality was evaluated in manual insertions by steering to predefined targets and a lateral displacement of 20 mm from the straight insertion line. Steering tasks were conducted in 5 directions and 2 tissue simulants under image guidance from a camera. The repeatability in instrument actuations was assessed during 100 mm deep automated insertions with a linear motor. In addition to tip position, tip angles were tracked during the insertions. The targeting error (mean absolute error ± standard deviation) during manual steering to 5 different targets in stiff tissue was 0.5 mm ± 1.1. This variability in manual tip placement (1.1 mm) was less than the variability among automated insertions (1.4 mm) in the same tissue type. An increased tissue stiffness resulted in an increased lateral tip displacement. The tip angle was directly controlled by the user interface, and remained unaffected by the tissue stiffness. This study demonstrates the ability to manually steer needles to predefined target locations under image guidance. Copyright © 2016 SIR. Published by Elsevier Inc. All rights reserved.

Manual for monitoring the quality of nursing home care records.

PubMed

Barbosa, Silvia Freitas; Tronchin, Daisy Maria Rizatto

2015-01-01

to build and validate an instrument aimed at monitoring the quality of nursing records in the Home Care Program (HCP) of a university hospital. methodological study involving the elaboration of a manual, whose content was later submitted to six experts for validation, reaching a ≥ 80% consensus. The data collection process was carried out in 2012 by means of a questionnaire comprised of the following issues: nursing evolution, nursing diagnosis, and nursing prescription, and standards for the nursing team recommended by the Regional Nursing Council of São Paulo and by the assessed institution. Manual items were judged according to the following variables: relevance, pertinence, clarity and simplicity. of the 39 propositions, 100% achieved ≥ 80% agreement in the relevance, pertinence and clarity variables; 92.3% in the simplicity variable. Sleep/rest, Mobility and Check-out variables did not reach a favorable minimum consensus in the prescribed activities and were improved following suggestions from the experts. we believe that the instrument will enable the improvement of the HCP's work process.

Quality Assurance and Control Considerations in Environmental Measurements and Monitoring

NASA Astrophysics Data System (ADS)

Sedlet, Jacob

1982-06-01

Quality assurance and quality control have become accepted as essential parts of all environmental surveillance, measurements, and monitoring programs, both nuclear and non-nuclear. The same principles and details apply to each. It is primarily the final measurement technique that differs. As the desire and need to measure smaller amounts of pollutants with greater accuracy has increased, it has been recognized that quality assurance and control programs are cost-effective in achieving the expected results. Quality assurance (QA) consists of all the actions necessary to provide confidence in the results. Quality control (QC) is a part of QA, and consists of those actions and activities that permit the control of the individual steps in the environmental program. The distinction between the two terms is not always clearly defined, but a sharp division is not necessary. The essential principle of QA and QC is a commitment to high quality results. The essential components of a QA and QC program are a complete, written procedures manual for all parts of the environmental program, the use of standard or validated procedures, participation in applicable interlaboratory comparison or QA programs, replicate analysis and measurement, training of personnel, and a means of auditing or checking that the QA and QC programs are properly conducted. These components are discussed below in some detail.

Efficacy of self-help manuals for anxiety disorders in primary care: a systematic review.

PubMed

van Boeijen, Christine A; van Balkom, Anton J L M; van Oppen, Patricia; Blankenstein, Nettie; Cherpanath, Ammani; van Dyck, Richard

2005-04-01

The purpose of this study was to review effectiveness studies of self-help manuals for anxiety disorders in primary care. A systematic review of six identified randomized controlled trials was carried out. In addition to outcome, the articles were coded on quality variables. The studies included differed with respect to the methodological quality, measurements used and size of the study population. Despite these differences, global results suggest that a self-help manual is an effective treatment possibility for primary care patients with anxiety disorders. The more time that was spent on guidance on the use of the self-help manual the greater was its effectiveness. Treatment with a self-help manual for anxiety disorders may be effective in primary care. Data are lacking on the feasibility and cost-effectiveness of these manuals.

Space Flight and Manual Control: Implications for Sensorimotor Function on Future Missions

NASA Technical Reports Server (NTRS)

Reschke, Millard F.; Kornilova, Ludmila; Tomilovskaya, Elena; Parker, Donald E.; Leigh, R. John; Kozlovskaya, Inessa

2009-01-01

Control of vehicles, and other complex mechanical motion systems, is a high-level integrative function of the central nervous system (CNS) that requires good visual acuity, eye-hand coordination, spatial (and, in some cases, geographic) orientation perception, and cognitive function. Existing evidence from space flight research (Paloski et.al., 2008, Clement and Reschke 2008, Reschke et al., 2007) demonstrates that the function of each of these systems is altered by removing (and subsequently by reintroducing) a gravitational field that can be sensed by vestibular, proprioceptive, and haptic receptors and used by the CNS for spatial orientation, navigation, and coordination of movements. Furthermore, much of the operational performance data collected as a function of space flight has not been available for independent analysis, and those data that have been reviewed are equivocal owing to uncontrolled environmental and/or engineering factors. Thus, our current understanding, when it comes to manual control, is limited primarily to a review of those situations where manual control has been a factor. One of the simplest approaches to the manual control problem is to review shuttle landing data. See the Figure below for those landing for which we have Shuttle velocities over the runway threshold.

[Effect of manual cleaning and machine cleaning for dental handpiece].

PubMed

Zhou, Xiaoli; Huang, Hao; He, Xiaoyan; Chen, Hui; Zhou, Xiaoying

2013-08-01

Comparing the dental handpiece' s cleaning effect between manual cleaning and machine cleaning. Eighty same contaminated dental handpieces were randomly divided into experimental group and control group, each group contains 40 pieces. The experimental group was treated by full automatic washing machine, and the control group was cleaned manually. The cleaning method was conducted according to the operations process standard, then ATP bioluminescence was used to test the cleaning results. Average relative light units (RLU) by ATP bioluminescence detection were as follows: Experimental group was 9, control group was 41. The two groups were less than the recommended RLU value provided by the instrument manufacturer (RLU < or = 45). There was significant difference between the two groups (P < 0.05). The cleaning quality of the experimental group was better than that of control group. It is recommended that the central sterile supply department should clean dental handpieces by machine to ensure the cleaning effect and maintain the quality.

Clinical practice guideline development manual: A quality-driven approach for translating evidence into action

PubMed Central

Rosenfeld, Richard M.; Shiffman, Richard N.

2010-01-01

Background Guidelines translate best evidence into best practice. A well-crafted guideline promotes quality by reducing healthcare variations, improving diagnostic accuracy, promoting effective therapy, and discouraging ineffective – or potentially harmful – interventions. Despite a plethora of published guidelines, methodology is often poorly defined and varies greatly within and among organizations. Purpose This manual describes the principles and practices used successfully by the American Academy of Otolaryngology – Head and Neck Surgery to produce quality-driven, evidence-based guidelines using efficient and transparent methodology for action-ready recommendations with multi-disciplinary applicability. The development process, which allows moving from conception to completion in twelve months, emphasizes a logical sequence of key action statements supported by amplifying text, evidence profiles, and recommendation grades that link action to evidence. Conclusions As clinical practice guidelines become more prominent as a key metric of quality healthcare, organizations must develop efficient production strategies that balance rigor and pragmatism. Equally important, clinicians must become savvy in understanding what guidelines are – and are not – and how they are best utilized to improve care. The information in this manual should help clinicians and organizations achieve these goals. PMID:19464525

Clinical practice guideline development manual: a quality-driven approach for translating evidence into action.

PubMed

Rosenfeld, Richard M; Shiffman, Richard N

2009-06-01

Guidelines translate best evidence into best practice. A well-crafted guideline promotes quality by reducing health-care variations, improving diagnostic accuracy, promoting effective therapy, and discouraging ineffective-or potentially harmful-interventions. Despite a plethora of published guidelines, methodology is often poorly defined and varies greatly within and among organizations. This manual describes the principles and practices used successfully by the American Academy of Otolaryngology-Head and Neck Surgery to produce quality-driven, evidence-based guidelines using efficient and transparent methodology for action-ready recommendations with multidisciplinary applicability. The development process, which allows moving from conception to completion in 12 months, emphasizes a logical sequence of key action statements supported by amplifying text, evidence profiles, and recommendation grades that link action to evidence. As clinical practice guidelines become more prominent as a key metric of quality health care, organizations must develop efficient production strategies that balance rigor and pragmatism. Equally important, clinicians must become savvy in understanding what guidelines are-and are not-and how they are best utilized to improve care. The information in this manual should help clinicians and organizations achieve these goals.

Influence of manual lymphatic drainage on health-related quality of life and symptoms of chronic venous insufficiency: a randomized controlled trial.

PubMed

dos Santos Crisóstomo, Rute Sofia; Costa, Daniela Sofia Albino; de Luz Belo Martins, Catarina; Fernandes, Tânia Isabel Russo; Armada-da-Silva, Paulo A

2015-02-01

To evaluate the efficacy of manual lymphatic drainage (MLD) in improving health-related quality of life (HRQOL), symptomatology, and physical status in patients with chronic venous insufficiency (CVI). Single-blind randomized controlled trial. Health community attendant service. Subjects with CVI (N=41) were randomly assigned to an experimental group (n=20; mean age, 54.6±11.3y) or control group (n=21; mean age, 46.8±11.1y). The experimental group completed 10 lower extremity MLD sessions over 4 weeks and 1 educational session. The control group only attended the educational session. Outcome measures were taken at baseline (t0), at the end of 4 weeks (t1), and after 2 months for follow-up (t2). HRQOL was assessed with the Chronic Venous Insufficiency Quality of Life Questionnaire-20, symptoms (fatigue, heaviness) were assessed with a visual analog scale, severity of the disease was assessed with the Venous Clinical Severity Score (VCSS) (total score, score for each item), leg volumetry was assessed with perimeters, and plantar/dorsiflexion strength and ankle range of motion (ROM) were assessed with dynamometry. A significant interaction group×time effect was found for pain on HRQOL (F2,78=3.507; P=.035; partial η2=.087), clinical severity (F2,78=5.231; P=.007; partial η2=.118), especially for venous edema (assessed with the VCSS), fatigue (F1.67,65.21=4.690; P=.012; partial η2=.107), and heaviness (F1.57,61.32=9.702; P=.001; partial η2=.199), with the experimental group improving from t0 to t1 and t0 to t2 in all of these outcomes. No effect of MLD treatment could be found for ankle muscle strength, ankle ROM, and leg volume. Short-term MLD treatment ameliorates CVI severity and related edema, symptoms, and pain HRQOL in patients with CVI. Copyright © 2015 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

A comparison of manual and controlled-force attachment-level measurements.

PubMed

Reddy, M S; Palcanis, K G; Geurs, N C

1997-12-01

This study compared the intra-examiner and inter-examiner error of 2 constant force probes to the reading of a conventional manual probe. 3 examiners made repeated examinations of attachment level using a modified Florida probe and a manual North Carolina probe (read to 1 mm or 0.5 mm); relative attachment level measurements were made using a Florida disk probe. One probe was used in each quadrant in 8 subjects with moderate to advanced periodontitis. Error was calculated as the mean of the absolute value of the difference between each examination, and the correlation between values at each examination calculated. Statistically-significant differences between probe type, examiners, and sites were detected using a repeated measures ANOVA accounting for the nesting within subjects. There was a significant difference in error by probe type (modified Florida probe 0.62 +/- 0.03 mm, r = 0.86; Florida stent probe 0.55 +/- 0.05 mm, r = 0.82; manual probe to 1 mm 0.39 +/- 0.02 mm, r = 0.88; manual probe to 0.5 mm 0.40 +/- 0.02 mm, r = 0.89; (p < 0.001). Significant differences were observed by examiners (p < 0.01). These data indicate that both manual and controlled-force probes can provide measurement within less than 1 mm of error; however, individual calibration of examiners remains important in the reduction of error.

Aeropropulsion facilities configuration control: Procedures manual

NASA Technical Reports Server (NTRS)

Lavelle, James J.

1990-01-01

Lewis Research Center senior management directed that the aeropropulsion facilities be put under configuration control. A Configuration Management (CM) program was established by the Facilities Management Branch of the Aeropropulsion Facilities and Experiments Division. Under the CM program, a support service contractor was engaged to staff and implement the program. The Aeronautics Directorate has over 30 facilities at Lewis of various sizes and complexities. Under the program, a Facility Baseline List (FBL) was established for each facility, listing which systems and their documents were to be placed under configuration control. A Change Control System (CCS) was established requiring that any proposed changes to FBL systems or their documents were to be processed as per the CCS. Limited access control of the FBL master drawings was implemented and an audit system established to ensure all facility changes are properly processed. This procedures manual sets forth the policy and responsibilities to ensure all key documents constituting a facilities configuration are kept current, modified as needed, and verified to reflect any proposed change. This is the essence of the CM program.

Solving the optimal attention allocation problem in manual control

NASA Technical Reports Server (NTRS)

Kleinman, D. L.

1976-01-01

Within the context of the optimal control model of human response, analytic expressions for the gradients of closed-loop performance metrics with respect to human operator attention allocation are derived. These derivatives serve as the basis for a gradient algorithm that determines the optimal attention that a human should allocate among several display indicators in a steady-state manual control task. Application of the human modeling techniques are made to study the hover control task for a CH-46 VTOL flight tested by NASA.

Mindcontrol: A web application for brain segmentation quality control.

PubMed

Keshavan, Anisha; Datta, Esha; M McDonough, Ian; Madan, Christopher R; Jordan, Kesshi; Henry, Roland G

2018-04-15

Tissue classification plays a crucial role in the investigation of normal neural development, brain-behavior relationships, and the disease mechanisms of many psychiatric and neurological illnesses. Ensuring the accuracy of tissue classification is important for quality research and, in particular, the translation of imaging biomarkers to clinical practice. Assessment with the human eye is vital to correct various errors inherent to all currently available segmentation algorithms. Manual quality assurance becomes methodologically difficult at a large scale - a problem of increasing importance as the number of data sets is on the rise. To make this process more efficient, we have developed Mindcontrol, an open-source web application for the collaborative quality control of neuroimaging processing outputs. The Mindcontrol platform consists of a dashboard to organize data, descriptive visualizations to explore the data, an imaging viewer, and an in-browser annotation and editing toolbox for data curation and quality control. Mindcontrol is flexible and can be configured for the outputs of any software package in any data organization structure. Example configurations for three large, open-source datasets are presented: the 1000 Functional Connectomes Project (FCP), the Consortium for Reliability and Reproducibility (CoRR), and the Autism Brain Imaging Data Exchange (ABIDE) Collection. These demo applications link descriptive quality control metrics, regional brain volumes, and thickness scalars to a 3D imaging viewer and editing module, resulting in an easy-to-implement quality control protocol that can be scaled for any size and complexity of study. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

26. DETAIL VIEW OF THE ADJUSTABLE FIELD RESISTTOR MANUAL CONTROLS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. DETAIL VIEW OF THE ADJUSTABLE FIELD RESISTTOR MANUAL CONTROLS AND SWITCH BOXES. - Potomac Power Plant, On West Virginia Shore of Potomac River, about 1 mile upriver from confluence with Shenandoah River, Harpers Ferry, Jefferson County, WV

Manual therapy and exercise for rotator cuff disease.

PubMed

Page, Matthew J; Green, Sally; McBain, Brodwen; Surace, Stephen J; Deitch, Jessica; Lyttle, Nicolette; Mrocki, Marshall A; Buchbinder, Rachelle

2016-06-10

Management of rotator cuff disease often includes manual therapy and exercise, usually delivered together as components of a physical therapy intervention. This review is one of a series of reviews that form an update of the Cochrane review, 'Physiotherapy interventions for shoulder pain'. To synthesise available evidence regarding the benefits and harms of manual therapy and exercise, alone or in combination, for the treatment of people with rotator cuff disease. We searched the Cochrane Central Register of Controlled Trials (CENTRAL; 2015, Issue 3), Ovid MEDLINE (January 1966 to March 2015), Ovid EMBASE (January 1980 to March 2015), CINAHL Plus (EBSCO, January 1937 to March 2015), ClinicalTrials.gov and the WHO ICTRP clinical trials registries up to March 2015, unrestricted by language, and reviewed the reference lists of review articles and retrieved trials, to identify potentially relevant trials. We included randomised and quasi-randomised trials, including adults with rotator cuff disease, and comparing any manual therapy or exercise intervention with placebo, no intervention, a different type of manual therapy or exercise or any other intervention (e.g. glucocorticoid injection). Interventions included mobilisation, manipulation and supervised or home exercises. Trials investigating the primary or add-on effect of manual therapy and exercise were the main comparisons of interest. Main outcomes of interest were overall pain, function, pain on motion, patient-reported global assessment of treatment success, quality of life and the number of participants experiencing adverse events. Two review authors independently selected trials for inclusion, extracted the data, performed a risk of bias assessment and assessed the quality of the body of evidence for the main outcomes using the GRADE approach. We included 60 trials (3620 participants), although only 10 addressed the main comparisons of interest. Overall risk of bias was low in three, unclear in 14 and high in

Field Operations and Enforcement Manual for Air Pollution Control. Volume II: Control Technology and General Source Inspection.

ERIC Educational Resources Information Center

Weisburd, Melvin I.

The Field Operations and Enforcement Manual for Air Pollution Control, Volume II, explains in detail the following: technology of source control, modification of operations, particulate control equipment, sulfur dioxide removal systems for power plants, and control equipment for gases and vapors; inspection procedures for general sources, fuel…

[Development of quality assurance/quality control web system in radiotherapy].

PubMed

Okamoto, Hiroyuki; Mochizuki, Toshihiko; Yokoyama, Kazutoshi; Wakita, Akihisa; Nakamura, Satoshi; Ueki, Heihachi; Shiozawa, Keiko; Sasaki, Koji; Fuse, Masashi; Abe, Yoshihisa; Itami, Jun

2013-12-01

Our purpose is to develop a QA/QC (quality assurance/quality control) web system using a server-side script language such as HTML (HyperText Markup Language) and PHP (Hypertext Preprocessor), which can be useful as a tool to share information about QA/QC in radiotherapy. The system proposed in this study can be easily built in one's own institute, because HTML can be easily handled. There are two desired functions in a QA/QC web system: (i) To review the results of QA/QC for a radiotherapy machine, manuals, and reports necessary for routinely performing radiotherapy through this system. By disclosing the results, transparency can be maintained, (ii) To reveal a protocol for QA/QC in one's own institute using pictures and movies relating to QA/QC for simplicity's sake, which can also be used as an educational tool for junior radiation technologists and medical physicists. By using this system, not only administrators, but also all staff involved in radiotherapy, can obtain information about the conditions and accuracy of treatment machines through the QA/QC web system.

[Report quality of randomized controlled trials of moxibustion for knee osteoarthritis based on CONSORT and STRICTOM].

PubMed

Xiong, Jun; Zhu, Daocheng; Chen, Rixin; Ye, Wenguo

2015-08-01

The report quality of randomized controlled trials (RCTs) of moxibustion for knee osteoarthritis (KOA) in China was evaluated by Consolidated Standards for Reporting of Trials (CONSORT) and Standards for Reporting Interventions in Controlled Trials of Moxibustion (STRICTOM). Computer and manual retrieval was used. Four databases of China National Knowledge Infrastructure (CNKD, China Biomedicine (CBM), VIP and WNFANG were searched in combination with manual retrieval for relevant journals to screen the literature that: met the inclusive criteria, and CONSORT and STRICTOM were used to assess the report quality. A total of 52 RCTs were included. It was found that unclear description of random methods, low use of blind methods, no allocation concealment, no sample size calculation, no intention-to-treat analysis,inadequate report of moxibustion details and no mention of practitioners background existed in the majority of the RCTs. Although the quality of RCTs of moxibustion for KOA was generally low, reducing the reliability and homogeneous comparability of the reports ,the quality of heat-sensitive moxibustion RCTs was high. It was believed that in order to improve the reliability and quality of RCTs of moxibustion, CONSORT and STRICTOM should be introduced into the RCT design of moxibustion and be strictly performed.

76 FR 54156 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-31

... traffic control device design, location, or operation that have made some existing devices in the field...-2010-0159] RIN 2125-AF43 National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for Streets and Highways; Revision AGENCY: Federal Highway Administration (FHWA...

The comparison of manual and LabVIEW-based fuzzy control on mechanical ventilation.

PubMed

Guler, Hasan; Ata, Fikret

2014-09-01

The aim of this article is to develop a knowledge-based therapy for management of rats with respiratory distress. A mechanical ventilator was designed to achieve this aim. The designed ventilator is called an intelligent mechanical ventilator since fuzzy logic was used to control the pneumatic equipment according to the rat's status. LabVIEW software was used to control all equipments in the ventilator prototype and to monitor respiratory variables in the experiment. The designed ventilator can be controlled both manually and by fuzzy logic. Eight female Wistar-Albino rats were used to test the designed ventilator and to show the effectiveness of fuzzy control over manual control on pressure control ventilation mode. The anesthetized rats were first ventilated for 20 min manually. After that time, they were ventilated for 20 min by fuzzy logic. Student's t-test for p < 0.05 was applied to the measured minimum, maximum and mean peak inspiration pressures to analyze the obtained results. The results show that there is no statistical difference in the rat's lung parameters before and after the experiments. It can be said that the designed ventilator and developed knowledge-based therapy support artificial respiration of living things successfully. © IMechE 2014.

User’s manual for the Automated Data Assurance and Management application developed for quality control of Everglades Depth Estimation Network water-level data

USGS Publications Warehouse

Petkewich, Matthew D.; Daamen, Ruby C.; Roehl, Edwin A.; Conrads, Paul

2016-09-29

The generation of Everglades Depth Estimation Network (EDEN) daily water-level and water-depth maps is dependent on high quality real-time data from over 240 water-level stations. To increase the accuracy of the daily water-surface maps, the Automated Data Assurance and Management (ADAM) tool was created by the U.S. Geological Survey as part of Greater Everglades Priority Ecosystems Science. The ADAM tool is used to provide accurate quality-assurance review of the real-time data from the EDEN network and allows estimation or replacement of missing or erroneous data. This user’s manual describes how to install and operate the ADAM software. File structure and operation of the ADAM software is explained using examples.

Gait parameter control timing with dynamic manual contact or visual cues.

PubMed

Rabin, Ely; Shi, Peter; Werner, William

2016-06-01

We investigated the timing of gait parameter changes (stride length, peak toe velocity, and double-, single-support, and complete step duration) to control gait speed. Eleven healthy participants adjusted their gait speed on a treadmill to maintain a constant distance between them and a fore-aft oscillating cue (a place on a conveyor belt surface). The experimental design balanced conditions of cue modality (vision: eyes-open; manual contact: eyes-closed while touching the cue); treadmill speed (0.2, 0.4, 0.85, and 1.3 m/s); and cue motion (none, ±10 cm at 0.09, 0.11, and 0.18 Hz). Correlation analyses revealed a number of temporal relationships between gait parameters and cue speed. The results suggest that neural control ranged from feedforward to feedback. Specifically, step length preceded cue velocity during double-support duration suggesting anticipatory control. Peak toe velocity nearly coincided with its most-correlated cue velocity during single-support duration. The toe-off concluding step and double-support durations followed their most-correlated cue velocity, suggesting feedback control. Cue-tracking accuracy and cue velocity correlations with timing parameters were higher with the manual contact cue than visual cue. The cue/gait timing relationships generalized across cue modalities, albeit with greater delays of step-cycle events relative to manual contact cue velocity. We conclude that individual kinematic parameters of gait are controlled to achieve a desired velocity at different specific times during the gait cycle. The overall timing pattern of instantaneous cue velocities associated with different gait parameters is conserved across cues that afford different performance accuracies. This timing pattern may be temporally shifted to optimize control. Different cue/gait parameter latencies in our nonadaptation paradigm provide general-case evidence of the independent control of gait parameters previously demonstrated in gait adaptation paradigms

Gait parameter control timing with dynamic manual contact or visual cues

PubMed Central

Shi, Peter; Werner, William

2016-01-01

We investigated the timing of gait parameter changes (stride length, peak toe velocity, and double-, single-support, and complete step duration) to control gait speed. Eleven healthy participants adjusted their gait speed on a treadmill to maintain a constant distance between them and a fore-aft oscillating cue (a place on a conveyor belt surface). The experimental design balanced conditions of cue modality (vision: eyes-open; manual contact: eyes-closed while touching the cue); treadmill speed (0.2, 0.4, 0.85, and 1.3 m/s); and cue motion (none, ±10 cm at 0.09, 0.11, and 0.18 Hz). Correlation analyses revealed a number of temporal relationships between gait parameters and cue speed. The results suggest that neural control ranged from feedforward to feedback. Specifically, step length preceded cue velocity during double-support duration suggesting anticipatory control. Peak toe velocity nearly coincided with its most-correlated cue velocity during single-support duration. The toe-off concluding step and double-support durations followed their most-correlated cue velocity, suggesting feedback control. Cue-tracking accuracy and cue velocity correlations with timing parameters were higher with the manual contact cue than visual cue. The cue/gait timing relationships generalized across cue modalities, albeit with greater delays of step-cycle events relative to manual contact cue velocity. We conclude that individual kinematic parameters of gait are controlled to achieve a desired velocity at different specific times during the gait cycle. The overall timing pattern of instantaneous cue velocities associated with different gait parameters is conserved across cues that afford different performance accuracies. This timing pattern may be temporally shifted to optimize control. Different cue/gait parameter latencies in our nonadaptation paradigm provide general-case evidence of the independent control of gait parameters previously demonstrated in gait adaptation paradigms

Proceedings of the 8th Annual Conference on Manual Control

NASA Technical Reports Server (NTRS)

Pew, R. W.

1972-01-01

The volume presents recent developments in the field of manual control theory and applications. The papers give analytical methods as well as examples of the important interplay between man and machine, such as how man controls and stabilizes machine dynamics, and how machines extend man's capability. Included in the broad range of subjects are procedures to evaluate and identify display systems, controllers, manipulators, human operators, aircraft, and non-flying vehicles. Of particular interest is the continuing trend of applying control theory to problems in medicine and psychology, as well as to problems in vehicle control.

Improving transcriptome construction in non-model organisms: integrating manual and automated gene definition in Emiliania huxleyi.

PubMed

Feldmesser, Ester; Rosenwasser, Shilo; Vardi, Assaf; Ben-Dor, Shifra

2014-02-22

The advent of Next Generation Sequencing technologies and corresponding bioinformatics tools allows the definition of transcriptomes in non-model organisms. Non-model organisms are of great ecological and biotechnological significance, and consequently the understanding of their unique metabolic pathways is essential. Several methods that integrate de novo assembly with genome-based assembly have been proposed. Yet, there are many open challenges in defining genes, particularly where genomes are not available or incomplete. Despite the large numbers of transcriptome assemblies that have been performed, quality control of the transcript building process, particularly on the protein level, is rarely performed if ever. To test and improve the quality of the automated transcriptome reconstruction, we used manually defined and curated genes, several of them experimentally validated. Several approaches to transcript construction were utilized, based on the available data: a draft genome, high quality RNAseq reads, and ESTs. In order to maximize the contribution of the various data, we integrated methods including de novo and genome based assembly, as well as EST clustering. After each step a set of manually curated genes was used for quality assessment of the transcripts. The interplay between the automated pipeline and the quality control indicated which additional processes were required to improve the transcriptome reconstruction. We discovered that E. huxleyi has a very high percentage of non-canonical splice junctions, and relatively high rates of intron retention, which caused unique issues with the currently available tools. While individual tools missed genes and artificially joined overlapping transcripts, combining the results of several tools improved the completeness and quality considerably. The final collection, created from the integration of several quality control and improvement rounds, was compared to the manually defined set both on the DNA and

77 FR 28460 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-14

...-2010-0159] RIN 2125-AF43 National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for Streets and Highways; Revision AGENCY: Federal Highway Administration (FHWA..., approved by the FHWA, and recognized as the national standard for traffic control devices used on all...

Improving the quality of child anthropometry: Manual anthropometry in the Body Imaging for Nutritional Assessment Study (BINA).

PubMed

Conkle, Joel; Ramakrishnan, Usha; Flores-Ayala, Rafael; Suchdev, Parminder S; Martorell, Reynaldo

2017-01-01

Anthropometric data collected in clinics and surveys are often inaccurate and unreliable due to measurement error. The Body Imaging for Nutritional Assessment Study (BINA) evaluated the ability of 3D imaging to correctly measure stature, head circumference (HC) and arm circumference (MUAC) for children under five years of age. This paper describes the protocol for and the quality of manual anthropometric measurements in BINA, a study conducted in 2016-17 in Atlanta, USA. Quality was evaluated by examining digit preference, biological plausibility of z-scores, z-score standard deviations, and reliability. We calculated z-scores and analyzed plausibility based on the 2006 WHO Child Growth Standards (CGS). For reliability, we calculated intra- and inter-observer Technical Error of Measurement (TEM) and Intraclass Correlation Coefficient (ICC). We found low digit preference; 99.6% of z-scores were biologically plausible, with z-score standard deviations ranging from 0.92 to 1.07. Total TEM was 0.40 for stature, 0.28 for HC, and 0.25 for MUAC in centimeters. ICC ranged from 0.99 to 1.00. The quality of manual measurements in BINA was high and similar to that of the anthropometric data used to develop the WHO CGS. We attributed high quality to vigorous training, motivated and competent field staff, reduction of non-measurement error through the use of technology, and reduction of measurement error through adequate monitoring and supervision. Our anthropometry measurement protocol, which builds on and improves upon the protocol used for the WHO CGS, can be used to improve anthropometric data quality. The discussion illustrates the need to standardize anthropometric data quality assessment, and we conclude that BINA can provide a valuable evaluation of 3D imaging for child anthropometry because there is comparison to gold-standard, manual measurements.

Improving the quality of child anthropometry: Manual anthropometry in the Body Imaging for Nutritional Assessment Study (BINA)

PubMed Central

2017-01-01

Anthropometric data collected in clinics and surveys are often inaccurate and unreliable due to measurement error. The Body Imaging for Nutritional Assessment Study (BINA) evaluated the ability of 3D imaging to correctly measure stature, head circumference (HC) and arm circumference (MUAC) for children under five years of age. This paper describes the protocol for and the quality of manual anthropometric measurements in BINA, a study conducted in 2016–17 in Atlanta, USA. Quality was evaluated by examining digit preference, biological plausibility of z-scores, z-score standard deviations, and reliability. We calculated z-scores and analyzed plausibility based on the 2006 WHO Child Growth Standards (CGS). For reliability, we calculated intra- and inter-observer Technical Error of Measurement (TEM) and Intraclass Correlation Coefficient (ICC). We found low digit preference; 99.6% of z-scores were biologically plausible, with z-score standard deviations ranging from 0.92 to 1.07. Total TEM was 0.40 for stature, 0.28 for HC, and 0.25 for MUAC in centimeters. ICC ranged from 0.99 to 1.00. The quality of manual measurements in BINA was high and similar to that of the anthropometric data used to develop the WHO CGS. We attributed high quality to vigorous training, motivated and competent field staff, reduction of non-measurement error through the use of technology, and reduction of measurement error through adequate monitoring and supervision. Our anthropometry measurement protocol, which builds on and improves upon the protocol used for the WHO CGS, can be used to improve anthropometric data quality. The discussion illustrates the need to standardize anthropometric data quality assessment, and we conclude that BINA can provide a valuable evaluation of 3D imaging for child anthropometry because there is comparison to gold-standard, manual measurements. PMID:29240796

Proceedings of the Annual Conference on Manual Control (15th) held March 20 - 22, 1979, Wright State University, Dayton, Ohio

DTIC Science & Technology

1979-11-01

Performance in a Precognitive Tracking Task," Proc. 13th Annual Conf. on Manual Control, pp. 152-165, June 1977. (32] Repa Brian S. and Robert S. Zucker...operators that have received attention in manual control. Precognitive manual control displays differ from the pursuit and compensatory displays of the

Logistics and operations implications of manual control of spacecraft docking maneuvers

NASA Technical Reports Server (NTRS)

Brody, Adam R.; Ellis, Stephen R.

1991-01-01

The implications of logistics and operations on the manual control of spacecraft docking are discussed. The results of simulation studies to investigate fuel and time cost tradeoffs are reviewed and discussed. Comparisons of acceleration control and pulse control are presented to evaluate the effects of astronauts being instructed to use pulse mode for fuel conservation. The applications of the findings to moon and Mars missions are addressed.

Prophylactic antibiotics for manual removal of retained placenta in vaginal birth.

PubMed

Chongsomchai, Chompilas; Lumbiganon, Pisake; Laopaiboon, Malinee

2014-10-20

Retained placenta is a potentially life-threatening condition because of its association with postpartum hemorrhage. Manual removal of placenta increases the likelihood of bacterial contamination in the uterine cavity. To compare the effectiveness and side-effects of routine antibiotic use for manual removal of placenta in vaginal birth in women who received antibiotic prophylaxis and those who did not and to identify the appropriate regimen of antibiotic prophylaxis for this procedure. We searched the Cochrane Pregnancy and Childbirth Group's Trials Register (31 July 2014). All randomized controlled trials comparing antibiotic prophylaxis and placebo or non antibiotic use to prevent endometritis after manual removal of placenta in vaginal birth. There are no included trials. In future updates, if we identify eligible trials, two review authors will independently assess trial quality and extract data No studies that met the inclusion criteria were identified. There are no randomized controlled trials to evaluate the effectiveness of antibiotic prophylaxis to prevent endometritis after manual removal of placenta in vaginal birth.

The Relative Effects of Manual Versus Automatic Exposure Control on Radiation Dose to Vital Organs in Total Hip Arthroplasty.

PubMed

Harper, Katharine D; Li, Shidong; Jennings, Rachel; Amer, Kamil M; Haydel, Christopher; Ali, Sayed

2018-01-01

Technologic advances have reduced medical radiation exposure while maintaining image quality. The purpose of this study was to determine the effects of the presence of total hip arthroplasty implants, compared with native hips, on radiation exposure of the most radiosensitive organs when manual and automatic exposure control settings are used. Detection probes were placed at six locations (stomach, sigmoid colon, right pelvic wall, left pelvic wall, pubic symphysis, and anterior pubic skin) in a cadaver. Radiographs were obtained with the use of manual and automatic exposure control protocols, with exposures recorded. A total hip arthroplasty implant was placed in the cadaver, probe positioning was confirmed, and the radiographs were repeated, with exposure values recorded. The control probe placed at the stomach had values ranging from 0.00 mSv to 0.01 mSv in protocols with and without implants. With the manual protocol, exposures in the pelvis ranged from 0.36 mSv to 2.74 mSv in the native hip and from 0.33 mSv to 2.24 mSv after implant placement. The increases in exposure after implant placement, represented as relative risk, were as follows: stomach, 1.000; pubic symphysis, 0.818; left pelvic wall, 1.381; sigmoid colon, 1.550; right pelvic wall, 0.917; and anterior pubic skin, 1.015. With automatic exposure control, exposures in the pelvis ranged from 0.07 mSv to 0.89 mSv in the native hip and from 0.21 mSv to 1.15 mSv after implant placement. With automatic exposure control, the increases in exposure after implant placement, represented as relative risk, were as follows: stomach, 1.000; pubic symphysis, 1.292; left pelvic wall, 1.476; sigmoid colon, 2.182; right pelvic wall, 3.000; and anterior pubic skin, 1.378. The amount of radiation to which patients are exposed as a result of medical procedures or imaging, and whether exposure is associated with an increased risk of malignant transformation, are the subject of ongoing debate. We found that after insertion

Manual Manipulation of Engine Throttles for Emergency Flight Control

NASA Technical Reports Server (NTRS)

Burcham, Frank W., Jr.; Fullerton, C. Gordon; Maine, Trindel A.

2004-01-01

If normal aircraft flight controls are lost, emergency flight control may be attempted using only engines thrust. Collective thrust is used to control flightpath, and differential thrust is used to control bank angle. Flight test and simulation results on many airplanes have shown that pilot manipulation of throttles is usually adequate to maintain up-and-away flight, but is most often not capable of providing safe landings. There are techniques that will improve control and increase the chances of a survivable landing. This paper reviews the principles of throttles-only control (TOC), a history of accidents or incidents in which some or all flight controls were lost, manual TOC results for a wide range of airplanes from simulation and flight, and suggested techniques for flying with throttles only and making a survivable landing.

Self-reported skin symptoms and skin-related quality of life among Latino immigrant poultry processing and other manual workers.

PubMed

Quandt, Sara A; Newman, Jill C; Pichardo-Geisinger, Rita; Mora, Dana C; Chen, Haiying; Feldman, Steven R; Arcury, Thomas A

2014-05-01

Manual labor employment occurs in environments with exposures likely to impact skin-related quality of life (SRQOL). The objectives of this paper are to (1) document the dimensions of SRQOL, (2) examine its association with skin symptoms, and (3) identify the predictors of SRQOL in Latino manual workers. A population-based survey of 733 Latino manual workers obtained Dermatology Life Quality Index (DLQI) and skin symptoms in the prior year. Two-thirds of workers were employed in production. Skin symptoms in prior year were reported by 23%. Impaired SRQOL was reported by 23%. In multivariate analyses, reduced SRQOL was associated with age, occupation, childhood indigenous language use, and experience of skin symptoms in the prior year. Despite overall high SRQOL exposures in some immigrant occupational groups produce reduce SRQOL. This rural, immigrant population faces significant obstacles to obtaining dermatological care; efforts are needed to improve their SRQOL. © 2013 Wiley Periodicals, Inc.

[Manual trigger point therapy of shoulder pain : Randomized controlled study of effectiveness].

PubMed

Sohns, S; Schnieder, K; Licht, G; von Piekartz, H

2016-12-01

Although chronic shoulder pain is highly prevalent and myofascial trigger points (mTrP) are thought to be found in the majority of patients with shoulder complaints, the influence on the pain mechanism remains unclear. There are only very few controlled clinical studies on the effects of manual trigger point compression therapy. This randomized controlled trial (RCT) compared the short-term effects of manual trigger point compression therapy (n = 6) with manual sham therapy (n = 6) in patients with unilateral shoulder pain due to myofascial syndrome (MFS). The measurement data were collected before and after two sessions of therapy. Pressure pain thresholds (PPT) of mTrP and symmetrically located points on the asymptomatic side were measured together with neutral points in order to detect a potential unilateral or generalized hyperalgesia. Additionally, the pain was assessed on a visual analog scale (VAS) at rest and during movement and the neck disability index (NDI) and disabilities of the arm, shoulder and hand (DASH) questionnaires were also completed and evaluated. Both treatment modalities led to a significant improvement; however, the manual trigger point compression therapy was significantly more effective in comparison to sham therapy, as measured by different parameters. The significant improvement of PPT values in the interventional group even at sites that were not directly treated, indicates central mechanisms in pain threshold modulation induced by manual compression therapy. The weaker but still measurable effects of sham therapy might be explained by the sham modality being a hands on technique or by sufficient stimulation of the trigger point region during the diagnostics and PPT measurements.

Relevance of Google-customized search engine vs. CISMeF quality-controlled health gateway.

PubMed

Gehanno, Jean-François; Kerdelhue, Gaétan; Sakji, Saoussen; Massari, Philippe; Joubert, Michel; Darmoni, Stéfan J

2009-01-01

CISMeF (acronym for Catalog and Index of French Language Health Resources on the Internet) is a quality-controlled health gateway conceived to catalog and index the most important and quality-controlled sources of institutional health information in French. The goal of this study is to compare the relevance of results provided by this gateway from a small set of documents selected and described by human experts to those provided by a search engine from a large set of automatically indexed and ranked resources. The Google-Customized search engine (CSE) was used. The evaluation was made using the 10th first results of 15 queries and two blinded physician evaluators. There was no significant difference between the relevance of information retrieval in CISMeF and Google CSE. In conclusion, automatic indexing does not lead to lower relevance than a manual MeSH indexing and may help to cope with the increasing number of references to be indexed in a controlled health quality gateway.

Manual control age and sex differences in 4 to 11 year old children.

PubMed

Flatters, Ian; Hill, Liam J B; Williams, Justin H G; Barber, Sally E; Mon-Williams, Mark

2014-01-01

To what degree does being male or female influence the development of manual skills in pre-pubescent children? This question is important because of the emphasis placed on developing important new manual skills during this period of a child's education (e.g. writing, drawing, using computers). We investigated age and sex-differences in the ability of 422 children to control a handheld stylus. A task battery deployed using tablet PC technology presented interactive visual targets on a computer screen whilst simultaneously recording participant's objective kinematic responses, via their interactions with the on-screen stimuli using the handheld stylus. The battery required children use the stylus to: (i) make a series of aiming movements, (ii) trace a series of abstract shapes and (iii) track a moving object. The tasks were not familiar to the children, allowing measurement of a general ability that might be meaningfully labelled 'manual control', whilst minimising culturally determined differences in experience (as much as possible). A reliable interaction between sex and age was found on the aiming task, with girls' movement times being faster than boys in younger age groups (e.g. 4-5 years) but with this pattern reversing in older children (10-11 years). The improved performance in older boys on the aiming task is consistent with prior evidence of a male advantage for gross-motor aiming tasks, which begins to emerge during adolescence. A small but reliable sex difference was found in tracing skill, with girls showing a slightly higher level of performance than boys irrespective of age. There were no reliable sex differences between boys and girls on the tracking task. Overall, the findings suggest that prepubescent girls are more likely to have superior manual control abilities for performing novel tasks. However, these small population differences do not suggest that the sexes require different educational support whilst developing their manual skills.

Investigation of Control System and Display Variations on Spacecraft Handling Qualities for Docking with Stationary and Rotating Targets

NASA Technical Reports Server (NTRS)

Jackson, E. Bruce; Goodrich, Kenneth H.; Bailey, Randall E.; Barnes, James R.; Ragsdale, William A.; Neuhaus, Jason R.

2010-01-01

This paper documents the investigation into the manual docking of a preliminary version of the Crew Exploration Vehicle with stationary and rotating targets in Low Earth Orbit. The investigation was conducted at NASA Langley Research Center in the summer of 2008 in a repurposed fixed-base transport aircraft cockpit and involved nine evaluation astronauts and research pilots. The investigation quantified the benefits of a feed-forward reaction control system thruster mixing scheme to reduce translation-into-rotation coupling, despite unmodeled variations in individual thruster force levels and off-axis center of mass locations up to 12 inches. A reduced rate dead-band in the phase-plane attitude controller also showed some promise. Candidate predictive symbology overlaid on a docking ring centerline camera image did not improve handling qualities, but an innovative attitude status indicator symbol was beneficial. The investigation also showed high workload and handling quality problems when manual dockings were performed with a rotating target. These concerns indicate achieving satisfactory handling quality ratings with a vehicle configuration similar to the nominal Crew Exploration Vehicle may require additional automation.

Manual therapy for plantar heel pain.

PubMed

Pollack, Yosefa; Shashua, Anat; Kalichman, Leonid

2018-03-01

Manual therapy employed in the treatment of plantar heel pain includes joint or soft tissue mobilizations. Efficacy of these methods is still under debate. To determine whether manual therapy, consisting of deep massage, myofascial release or joint mobilization is effective in treating plantar heel pain. A critical review of all available studies with an emphasis on randomized controlled trials (RCTs) was performed. PubMed, PEDro, and Google Scholar databases were searched for keywords relating to plantar heel pain, joint, and soft tissue mobilizations. There were no search limitations or language restrictions. The reference lists of all retrieved articles were searched. The PEDro score was used to assess the quality of the reviewed papers. A total of six relevant RCTs were found: two examined the effectiveness of joint mobilization on plantar heel pain and four the effectiveness of soft tissue techniques. Five studies showed a positive short-term effect after manual therapy treatment, mostly soft tissue mobilizations, with or without stretching exercises for patients with plantar heel pain, compared to other treatments. One study observed that adding joint mobilization to the treatment of plantar heel pain was not effective. The quality of all studies was moderate to high. According to reviewed moderate and high-quality RCTs, soft tissue mobilization is an effective modality for treating plantar heel pain. Outcomes of joint mobilizations are controversial. Further studies are needed to evaluate the short and long-term effect of different soft tissue mobilization techniques. Copyright © 2017 Elsevier Ltd. All rights reserved.

Decreasing recurrent bowel obstructions, improving quality of life with physiotherapy: Controlled study.

PubMed

Rice, Amanda D; Patterson, Kimberley; Reed, Evette D; Wurn, Belinda F; Robles, Kristen; Klingenberg, Bernhard; Weinstock, Leonard B; Pratt, Janey Sa; King, C Richard; Wurn, Lawrence J

2018-05-21

To compare (1) quality of life and (2) rate of recurrent small bowel obstructions (SBO) for patients treated with novel manual physiotherapy vs no treatment. One hundred and three subjects (age 19-89) with a history of recurrent adhesive SBO were treated with a manual physiotherapy called the Clear Passage Approach (CPA) which focused on decreasing adhesive crosslinking in abdominopelvic viscera. Pre- and post-therapy data measured recurring obstructions and quality of life, using a validated test sent 90 d after therapy. Results were compared to 136 untreated control subjects who underwent the same measurements for subjects who did not receive any therapy, which is the normal course for patients with recurring SBO. Comparison of the groups allowed us to assess changes when the physiotherapy was added as an adjunct treatment for patients with recurring SBO. Despite histories of more prior hospitalizations, obstructions, surgeries, and years impacted by bowel issues, the 103 CPA-treated subjects reported a significantly lower rate of repeat SBO than 136 untreated controls (total obstructions P = 0.0003; partial obstructions P = 0.0076). Subjects treated with the therapy demonstrated significant improvements in five of six total domains in the validated Small Bowel Obstruction Questionnaire (SBO-Q). Domains of diet, pain, gastrointestinal symptoms, quality of life (QOL) and pain severity when compared to post CPA treatment were significantly improved ( P < 0.0001). The medication domain was not changed in the CPA treated group ( P = 0.176). CPA physical therapy was effective for patients with adhesive SBO with significantly lower recurrence rate, improvement in reported symptoms and overall quality of life of subjects.

Quality Control by Artificial Vision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lam, Edmond Y.; Gleason, Shaun Scott; Niel, Kurt S.

2010-01-01

Computational technology has fundamentally changed many aspects of our lives. One clear evidence is the development of artificial-vision systems, which have effectively automated many manual tasks ranging from quality inspection to quantitative assessment. In many cases, these machine-vision systems are even preferred over manual ones due to their repeatability and high precision. Such advantages come from significant research efforts in advancing sensor technology, illumination, computational hardware, and image-processing algorithms. Similar to the Special Section on Quality Control by Artificial Vision published two years ago in Volume 17, Issue 3 of the Journal of Electronic Imaging, the present one invited papersmore » relevant to fundamental technology improvements to foster quality control by artificial vision, and fine-tuned the technology for specific applications. We aim to balance both theoretical and applied work pertinent to this special section theme. Consequently, we have seven high-quality papers resulting from the stringent peer-reviewing process in place at the Journal of Electronic Imaging. Some of the papers contain extended treatment of the authors work presented at the SPIE Image Processing: Machine Vision Applications conference and the International Conference on Quality Control by Artificial Vision. On the broad application side, Liu et al. propose an unsupervised texture image segmentation scheme. Using a multilayer data condensation spectral clustering algorithm together with wavelet transform, they demonstrate the effectiveness of their approach on both texture and synthetic aperture radar images. A problem related to image segmentation is image extraction. For this, O'Leary et al. investigate the theory of polynomial moments and show how these moments can be compared to classical filters. They also show how to use the discrete polynomial-basis functions for the extraction of 3-D embossed digits, demonstrating superiority over Fourier

Improved Statistical Method For Hydrographic Climatic Records Quality Control

NASA Astrophysics Data System (ADS)

Gourrion, J.; Szekely, T.

2016-02-01

Climate research benefits from the continuous development of global in-situ hydrographic networks in the last decades. Apart from the increasing volume of observations available on a large range of temporal and spatial scales, a critical aspect concerns the ability to constantly improve the quality of the datasets. In the context of the Coriolis Dataset for ReAnalysis (CORA) version 4.2, a new quality control method based on a local comparison to historical extreme values ever observed is developed, implemented and validated. Temperature, salinity and potential density validity intervals are directly estimated from minimum and maximum values from an historical reference dataset, rather than from traditional mean and standard deviation estimates. Such an approach avoids strong statistical assumptions on the data distributions such as unimodality, absence of skewness and spatially homogeneous kurtosis. As a new feature, it also allows addressing simultaneously the two main objectives of a quality control strategy, i.e. maximizing the number of good detections while minimizing the number of false alarms. The reference dataset is presently built from the fusion of 1) all ARGO profiles up to early 2014, 2) 3 historical CTD datasets and 3) the Sea Mammals CTD profiles from the MEOP database. All datasets are extensively and manually quality controlled. In this communication, the latest method validation results are also presented. The method has been implemented in the latest version of the CORA dataset and will benefit to the next version of the Copernicus CMEMS dataset.

Efficacy of manual therapy in the treatment of tension-type headache. A systematic review from 2000-2013.

PubMed

Lozano López, C; Mesa Jiménez, J; de la Hoz Aizpurúa, J L; Pareja Grande, J; Fernández de Las Peñas, C

2016-01-01

To study the efficacy of manual therapy in the treatment of tension-type headache (TTH) by assessing the quality of randomized control trials (RCTs) published from the year 2000 to April 2013. A search was performed in the following databases: MEDLINE, EBSCO, CINAHL, SCOPUS, PEDRO and OVID. An analysis was made of RCT including patients with TTH receiving any manual therapy, and assessing outcome measures including the intensity, and frequency or duration of the headache. Two independent referees reviewed the methodological quality of RCTs using the Jadad scale. Data from the studies were extracted by two different reviewers. A total of fourteen RCTs were selected. Twelve studies showed acceptable quality (Jadad scale ≥3), and the remaining 2 had low quality (Jadad=2). The studies showed positive results, including reduction in headache intensity and/or frequency, reduction of medication consumption, and improvement in quality of life. The effectiveness of manual therapy for TTH cannot be completely assessed due to the heterogeneity in study design, outcome measures, and different treatments. Nevertheless, the results suggest patients with TTH receiving manual therapies showed better progress than those receiving conventional treatment or placebo. Further studies of high quality using manual therapy protocols, and also including standardized outcome measures, are now needed to clarify the efficacy of manual therapy in the management of TTH. Copyright © 2013 Sociedad Española de Neurología. Publicado por Elsevier España, S.L.U. All rights reserved.

Scientific computation systems quality branch manual

NASA Technical Reports Server (NTRS)

1972-01-01

A manual is presented which is designed to familiarize the GE 635 user with the configuration and operation of the overall system. Work submission, programming standards, restrictions, testing and debugging, and related general information is provided for GE 635 programmer.

Comparison of Power Versus Manual Injection in Bolus Shape and Image Quality on Contrast-Enhanced Magnetic Resonance Angiography: An Experimental Study in a Swine Model.

PubMed

Tsuboyama, Takahiro; Jost, Gregor; Pietsch, Hubertus; Tomiyama, Noriyuki

2017-09-01

The aim of this study was to compare power versus manual injection in bolus shape and image quality on contrast-enhanced magnetic resonance angiography (CE-MRA). Three types of CE-MRA (head-neck 3-dimensional [3D] MRA with a test-bolus technique, thoracic-abdominal 3D MRA with a bolus-tracking technique, and thoracic-abdominal time-resolved 4-dimensional [4D] MRA) were performed after power and manual injection of gadobutrol (0.1 mmol/kg) at 2 mL/s in 12 pigs (6 sets of power and manual injections for each type of CE-MRA). For the quantitative analysis, the signal-to-noise ratio was measured on ascending aorta, descending aorta, brachiocephalic trunk, common carotid artery, and external carotid artery on the 6 sets of head-neck 3D MRA, and on ascending aorta, descending aorta, brachiocephalic trunk, abdominal aorta, celiac trunk, and renal artery on the 6 sets of thoracic-abdominal 3D MRA. Bolus shapes were evaluated on the 6 sets each of test-bolus scans and 4D MRA. For the qualitative analysis, arterial enhancement, superimposition of nontargeted enhancement, and overall image quality were evaluated on 3D MRA. Visibility of bolus transition was assessed on 4D MRA. Intraindividual comparison between power and manual injection was made by paired t test, Wilcoxon rank sum test, and analysis of variance by ranks. Signal-to-noise ratio on 3D MRA was statistically higher with power injection than with manual injection (P < 0.001). Bolus shapes (test-bolus, 4D MRA) were represented by a characteristic standard bolus curve (sharp first-pass peak followed by a gentle recirculation peak) in all the 12 scans with power injection, but only in 1 of the 12 scans with manual injection. Standard deviations of time-to-peak enhancement were smaller in power injection than in manual injection. Qualitatively, although both injection methods achieved diagnostic quality on 3D MRA, power injection exhibited significantly higher image quality than manual injection (P = 0.001) due to

Creating a systems engineering approach for the manual on uniform traffic control devices.

DOT National Transportation Integrated Search

2011-03-01

The Manual on Uniform Traffic Control Devices (MUTCD) provides basic principles for use of traffic : control devices (TCD). However, most TCDs are not explicitly required, and the decision to use a given : TCD in a given situation is typically made b...

A randomized controlled trial testing the efficacy of an HIV/AIDS symptom management manual.

PubMed

Wantland, Dean J; Holzemer, William L; Moezzi, Shahnaz; Willard, Suzanne S; Arudo, John; Kirksey, Kenn M; Portillo, Carmen J; Corless, Inge B; Rosa, María E; Robinson, Linda L; Nicholas, Patrice K; Hamilton, Mary Jane; Sefcik, Elizabeth F; Human, Sarie; Rivero, Marta M; Maryland, Mary; Huang, Emily

2008-09-01

This study investigates whether using an HIV/AIDS symptom management manual with self-care strategies for 21 common symptoms, compared to a basic nutrition manual, had an effect on reducing symptom frequency and intensity. A 775-person, repeated measures, randomized controlled trial was conducted over three months in 12 sites from the United States, Puerto Rico, and Africa to assess the relationship between symptom intensity with predictors for differences in initial symptom status and change over time. A mixed model growth analysis showed a significantly greater decline in symptom frequency and intensity for the group using the symptom management manual (intervention) compared to those using the nutrition manual (control) (t=2.36, P=0.018). The models identified three significant predictors for increased initial symptom intensities and in intensity change over time: (1) protease inhibitor-based therapy (increased mean intensity by 28%); (2) having comorbid illness (nearly twice the mean intensity); and (3) being Hispanic receiving care in the United States (increased the mean intensity by 2.5 times). In addition, the symptom manual showed a significantly higher helpfulness rating and was used more often compared to the nutrition manual. The reduction in symptom intensity scores provides evidence of the need for palliation of symptoms in individuals with HIV/AIDS, as well as symptoms and treatment side effects associated with other illnesses. The information from this study may help health care providers become more aware of self-management strategies that are useful to persons with HIV/AIDS and help them to assist patients in making informed choices.

An automated workflow for patient-specific quality control of contour propagation

NASA Astrophysics Data System (ADS)

Beasley, William J.; McWilliam, Alan; Slevin, Nicholas J.; Mackay, Ranald I.; van Herk, Marcel

2016-12-01

Contour propagation is an essential component of adaptive radiotherapy, but current contour propagation algorithms are not yet sufficiently accurate to be used without manual supervision. Manual review of propagated contours is time-consuming, making routine implementation of real-time adaptive radiotherapy unrealistic. Automated methods of monitoring the performance of contour propagation algorithms are therefore required. We have developed an automated workflow for patient-specific quality control of contour propagation and validated it on a cohort of head and neck patients, on which parotids were outlined by two observers. Two types of error were simulated—mislabelling of contours and introducing noise in the scans before propagation. The ability of the workflow to correctly predict the occurrence of errors was tested, taking both sets of observer contours as ground truth, using receiver operator characteristic analysis. The area under the curve was 0.90 and 0.85 for the observers, indicating good ability to predict the occurrence of errors. This tool could potentially be used to identify propagated contours that are likely to be incorrect, acting as a flag for manual review of these contours. This would make contour propagation more efficient, facilitating the routine implementation of adaptive radiotherapy.

The effectiveness of manual therapy in treating cervicogenic dizziness: a systematic review.

PubMed

Yaseen, Khalid; Hendrick, Paul; Ismail, Ayah; Felemban, Mohannad; Alshehri, Mansour Abdullah

2018-01-01

[Purpose] This review provides an evaluation of the evidence for the effectiveness of using manual therapy to treat cervicogenic dizziness. [Subjects and Methods] The literature was systematically searched on the May 2, 2016 using the following online databases: Medline, EMBASE, CINAHL and PEDro. This review included randomised controlled trials and compared the efficacy of manual therapy for the treatment of cervicogenic dizziness, compared to other types of intervention. This study measured changes based on dizziness intensity and frequency. [Results] The primary search found 30 articles, but only four articles met the inclusion criteria. Assessment of methodological quality was performed by two researchers using the PEDro scale. The level of evidence was determined using a recognised grading scale. Three out of the four articles were deemed to have high methodological quality, while the fourth was rated as moderate quality. The attributed level of evidence was moderate (level 2). [Conclusion] Manual therapy is potentially effective for managing cervicogenic dizziness. However, due to the heterogeneity of the results and techniques and the low number of studies, further research is recommended to provide conclusive evidence.

In Data We Trust? Comparison of Electronic Versus Manual Abstraction of Antimicrobial Prescribing Quality Metrics for Hospitalized Veterans With Pneumonia.

PubMed

Jones, Barbara E; Haroldsen, Candace; Madaras-Kelly, Karl; Goetz, Matthew B; Ying, Jian; Sauer, Brian; Jones, Makoto M; Leecaster, Molly; Greene, Tom; Fridkin, Scott K; Neuhauser, Melinda M; Samore, Matthew H

2018-07-01

Electronic health records provide the opportunity to assess system-wide quality measures. Veterans Affairs Pharmacy Benefits Management Center for Medication Safety uses medication use evaluation (MUE) through manual review of the electronic health records. To compare an electronic MUE approach versus human/manual review for extraction of antibiotic use (choice and duration) and severity metrics. Retrospective. Hospitalizations for uncomplicated pneumonia occurring during 2013 at 30 Veterans Affairs facilities. We compared summary statistics, individual hospitalization-level agreement, facility-level consistency, and patterns of variation between electronic and manual MUE for initial severity, antibiotic choice, daily clinical stability, and antibiotic duration. Among 2004 hospitalizations, electronic and manual abstraction methods showed high individual hospitalization-level agreement for initial severity measures (agreement=86%-98%, κ=0.5-0.82), antibiotic choice (agreement=89%-100%, κ=0.70-0.94), and facility-level consistency for empiric antibiotic choice (anti-MRSA r=0.97, P<0.001; antipseudomonal r=0.95, P<0.001) and therapy duration (r=0.77, P<0.001) but lower facility-level consistency for days to clinical stability (r=0.52, P=0.006) or excessive duration of therapy (r=0.55, P=0.005). Both methods identified widespread facility-level variation in antibiotic choice, but we found additional variation in manual estimation of excessive antibiotic duration and initial illness severity. Electronic and manual MUE agreed well for illness severity, antibiotic choice, and duration of therapy in pneumonia at both the individual and facility levels. Manual MUE showed additional reviewer-level variation in estimation of initial illness severity and excessive antibiotic use. Electronic MUE allows for reliable, scalable tracking of national patterns of antimicrobial use, enabling the examination of system-wide interventions to improve quality.

Computer code for controller partitioning with IFPC application: A user's manual

NASA Technical Reports Server (NTRS)

Schmidt, Phillip H.; Yarkhan, Asim

1994-01-01

A user's manual for the computer code for partitioning a centralized controller into decentralized subcontrollers with applicability to Integrated Flight/Propulsion Control (IFPC) is presented. Partitioning of a centralized controller into two subcontrollers is described and the algorithm on which the code is based is discussed. The algorithm uses parameter optimization of a cost function which is described. The major data structures and functions are described. Specific instructions are given. The user is led through an example of an IFCP application.

Manual control of yaw motion with combined visual and vestibular cues

NASA Technical Reports Server (NTRS)

Zacharias, G. L.; Young, L. R.

1977-01-01

Measurements are made of manual control performance in the closed-loop task of nulling perceived self-rotation velocity about an earth-vertical axis. Self-velocity estimation was modelled as a function of the simultaneous presentation of vestibular and peripheral visual field motion cues. Based on measured low-frequency operator behavior in three visual field environments, a parallel channel linear model is proposed which has separate visual and vestibular pathways summing in a complementary manner. A correction to the frequency responses is provided by a separate measurement of manual control performance in an analogous visual pursuit nulling task. The resulting dual-input describing function for motion perception dependence on combined cue presentation supports the complementary model, in which vestibular cues dominate sensation at frequencies above 0.05 Hz. The describing function model is extended by the proposal of a non-linear cue conflict model, in which cue weighting depends on the level of agreement between visual and vestibular cues.

MAVARIC - a comparison of automation-assisted and manual cervical screening: a randomised controlled trial.

PubMed

Kitchener, H C; Blanks, R; Cubie, H; Desai, M; Dunn, G; Legood, R; Gray, A; Sadique, Z; Moss, S

2011-01-01

The principal objective was to compare automation-assisted reading of cervical cytology with manual reading using the histological end point of cervical intraepithelial neoplasia grade II (CIN2) or worse (CIN2+). Secondary objectives included (i) an assessment of the slide ranking facility of the Becton Dickinson (BD) FocalPoint™ Slide Profiler (Becton Dickinson, Franklin Lakes, NJ, USA), especially 'No Further Review', (ii) a comparison of the two approved automated systems, the ThinPrep® Imaging System (Hologic, Bedford, MA, USA) and the BD FocalPoint Guided Screener Imaging System, and (iii) automated versus manual in terms of productivity and cost-effectiveness. A 1 : 2 randomised allocation of slides to either manual reading or automation-assisted paired with manual reading. Cytoscreeners were blinded to whether samples would be read only manually or manually paired with automated. Slide reading procedures followed real-life laboratory protocol to produce a final result and, for paired readings, the worse result determined the management. Costs per event were estimated and combined with productivity to produce a cost per slide, per woman and per CIN2+ and cervical intraepithelial neoplasia grade III (CIN3) or worse (CIN3+) lesion detected. Cost-effectiveness was estimated using cost per CIN2+ detected. Lifetime cost-effectiveness in terms of life-years and quality-adjusted life-years was estimated using a mathematical model. Liquid-based cytology samples were obtained in primary care, and a small number of abnormal samples were obtained from local colposcopy clinics, from different women, in order to enrich the proportion of abnormals. All of the samples were read in a single large service laboratory. Liquid residues used for human papillomavirus (HPV) triage were tested (with Hybrid Capture 2, Qiagen, Crawley, UK) in a specialist virology laboratory in Edinburgh, UK. Histopathology was read by a specialist gynaecological pathology team blinded to HPV

A Model of Manual Control with Perspective Scene Viewing

NASA Technical Reports Server (NTRS)

Sweet, Barbara Townsend

2013-01-01

A model of manual control during perspective scene viewing is presented, which combines the Crossover Model with a simpli ed model of perspective-scene viewing and visual- cue selection. The model is developed for a particular example task: an idealized constant- altitude task in which the operator controls longitudinal position in the presence of both longitudinal and pitch disturbances. An experiment is performed to develop and vali- date the model. The model corresponds closely with the experimental measurements, and identi ed model parameters are highly consistent with the visual cues available in the perspective scene. The modeling results indicate that operators used one visual cue for position control, and another visual cue for velocity control (lead generation). Additionally, operators responded more quickly to rotation (pitch) than translation (longitudinal).

Cost effectiveness of physiotherapy, manual therapy, and general practitioner care for neck pain: economic evaluation alongside a randomised controlled trial

PubMed Central

Bos, Ingeborg B C Korthals-de; Hoving, Jan L; van Tulder, Maurits W; Mölken, Maureen P M H Rutten-van; Adèr, Herman J; de Vet, Henrica C W; Koes, Bart W; Vondeling, Hindrik; Bouter, Lex M

2003-01-01

Objective To evaluate the cost effectiveness of physiotherapy, manual therapy, and care by a general practitioner for patients with neck pain. Design Economic evaluation alongside a randomised controlled trial. Setting Primary care. Participants 183 patients with neck pain for at least two weeks recruited by 42 general practitioners and randomly allocated to manual therapy (n=60, spinal mobilisation), physiotherapy (n=59, mainly exercise), or general practitioner care (n=64, counselling, education, and drugs). Main outcome measures Clinical outcomes were perceived recovery, intensity of pain, functional disability, and quality of life. Direct and indirect costs were measured by means of cost diaries that were kept by patients for one year. Differences in mean costs between groups, cost effectiveness, and cost utility ratios were evaluated by applying non-parametric bootstrapping techniques. Results The manual therapy group showed a faster improvement than the physiotherapy group and the general practitioner care group up to 26 weeks, but differences were negligible by follow up at 52 weeks. The total costs of manual therapy (€447; £273; $402) were around one third of the costs of physiotherapy (€1297) and general practitioner care (€1379). These differences were significant: P<0.01 for manual therapy versus physiotherapy and manual therapy versus general practitioner care and P=0.55 for general practitioner care versus physiotherapy. The cost effectiveness ratios and the cost utility ratios showed that manual therapy was less costly and more effective than physiotherapy or general practitioner care. Conclusions Manual therapy (spinal mobilisation) is more effective and less costly for treating neck pain than physiotherapy or care by a general practitioner. What is already known on this topicThe cost of treating neck pain is considerableMany conservative interventions are available, such as prescription drugs, yet their cost effectiveness has not been

Computer Numerical Control: Instructional Manual. The North Dakota High Technology Mobile Laboratory Project.

ERIC Educational Resources Information Center

Sinn, John W.

This instructional manual contains five learning activity packets for use in a workshop on computer numerical control for computer-aided manufacturing. The lessons cover the following topics: introduction to computer-aided manufacturing, understanding the lathe, using the computer, computer numerically controlled part programming, and executing a…

Improved statistical method for temperature and salinity quality control

NASA Astrophysics Data System (ADS)

Gourrion, Jérôme; Szekely, Tanguy

2017-04-01

Climate research and Ocean monitoring benefit from the continuous development of global in-situ hydrographic networks in the last decades. Apart from the increasing volume of observations available on a large range of temporal and spatial scales, a critical aspect concerns the ability to constantly improve the quality of the datasets. In the context of the Coriolis Dataset for ReAnalysis (CORA) version 4.2, a new quality control method based on a local comparison to historical extreme values ever observed is developed, implemented and validated. Temperature, salinity and potential density validity intervals are directly estimated from minimum and maximum values from an historical reference dataset, rather than from traditional mean and standard deviation estimates. Such an approach avoids strong statistical assumptions on the data distributions such as unimodality, absence of skewness and spatially homogeneous kurtosis. As a new feature, it also allows addressing simultaneously the two main objectives of an automatic quality control strategy, i.e. maximizing the number of good detections while minimizing the number of false alarms. The reference dataset is presently built from the fusion of 1) all ARGO profiles up to late 2015, 2) 3 historical CTD datasets and 3) the Sea Mammals CTD profiles from the MEOP database. All datasets are extensively and manually quality controlled. In this communication, the latest method validation results are also presented. The method has already been implemented in the latest version of the delayed-time CMEMS in-situ dataset and will be deployed soon in the equivalent near-real time products.

Manual de Adiestramiento sobre Terapia de Rehidratacion Oral y Control de las Enfermedades Diarreicas (Oral Rehydration Therapy and the Control of Diarrheal Diseases). Training for Development. Peace Corps Information Collection & Exchange Training Manual No. T-53.

ERIC Educational Resources Information Center

Clark, Mari; And Others

This Spanish-language manual was developed to train Peace Corps volunteers and other community health workers in Spanish-speaking countries in oral rehydration therapy (ORT) and the control of diarrheal diseases. Using a competency-based format, the manual contains three training modules (organized in seven sessions) that focus on interrelated…

Motion Perception and Manual Control Performance During Passive Tilt and Translation Following Space Flight

NASA Technical Reports Server (NTRS)

Clement, Gilles; Wood, Scott J.

2010-01-01

This joint ESA-NASA study is examining changes in motion perception following Space Shuttle flights and the operational implications of post-flight tilt-translation ambiguity for manual control performance. Vibrotactile feedback of tilt orientation is also being evaluated as a countermeasure to improve performance during a closed-loop nulling task. METHODS. Data has been collected on 5 astronaut subjects during 3 preflight sessions and during the first 8 days after Shuttle landings. Variable radius centrifugation (216 deg/s) combined with body translation (12-22 cm, peak-to-peak) is utilized to elicit roll-tilt perception (equivalent to 20 deg, peak-to-peak). A forward-backward moving sled (24-390 cm, peak-to-peak) with or without chair tilting in pitch is utilized to elicit pitch tilt perception (equivalent to 20 deg, peak-to-peak). These combinations are elicited at 0.15, 0.3, and 0.6 Hz for evaluating the effect of motion frequency on tilt-translation ambiguity. In both devices, a closed-loop nulling task is also performed during pseudorandom motion with and without vibrotactile feedback of tilt. All tests are performed in complete darkness. PRELIMINARY RESULTS. Data collection is currently ongoing. Results to date suggest there is a trend for translation motion perception to be increased at the low and medium frequencies on landing day compared to pre-flight. Manual control performance is improved with vibrotactile feedback. DISCUSSION. The results of this study indicate that post-flight recovery of motion perception and manual control performance is complete within 8 days following short-duration space missions. Vibrotactile feedback of tilt improves manual control performance both before and after flight.

Iowa Commercial Pesticide Applicator Manual, Category 1A: Agricultural Weed Control.

ERIC Educational Resources Information Center

Jennings, Vivan M.; Ryan, Stephen O.

This manual provides information needed to meet the standards for pesticide applicator certification. Weeds, their effects, and control in relation to crop production are presented. Pre- and post-emergence treatments are discussed for row crops such as corn and soybeans. Problems with herbicide application to grass pastures, small grains, and…

Operational quality control of daily precipitation using spatio-climatological consistency testing

NASA Astrophysics Data System (ADS)

Scherrer, S. C.; Croci-Maspoli, M.; van Geijtenbeek, D.; Naguel, C.; Appenzeller, C.

2010-09-01

Quality control (QC) of meteorological data is of utmost importance for climate related decisions. The search for an effective automated QC of precipitation data has proven difficult and many weather services still use mainly manual inspection of daily precipitation including MeteoSwiss. However, man power limitations force many weather services to move towards less labour intensive and more automated QC with the challenge to keeping data quality high. In the last decade, several approaches have been presented to objectify daily precipitation QC. Here we present a spatio-climatological approach that will be implemented operationally at MeteoSwiss. It combines the information from the event based spatial distribution of everyday's precipitation field and the historical information of the interpolation error using different precipitation intensity intervals. Expert judgement shows that the system is able to detect potential outliers very well (hardly any missed errors) without creating too many false alarms that need human inspection. 50-80% of all flagged values have been classified as real errors by the data editor. This is much better than the roughly 15-20% using standard spatial regression tests. Very helpful in the QC process is the automatic redistribution of accumulated several day sums. Manual inspection in operations can be reduced and the QC of precipitation objectified substantially.

[Effects of educational program of manual lymph massage on the arm functioning and the quality of life in breast cancer patients].

PubMed

Lee, Eun Sook; Kim, Sung Hyo; Kim, Sun Mi; Sun, Jeong Ju

2005-12-01

The purpose of this study was to determine the effect of EPMLM (educational program of manual lymph massage) on the arm functioning and QOL (quality of life) in breast cancer patients with lymphedema. Subjects in the experimental group (n=20) participated in EPMLM for 6 weeks from June to July, 2005. The EPMLM consisted of training of lymph massage for 2 weeks and encourage and support of self-care using lymph massage for 4 weeks. The arm functioning assessed at pre-treatment, 2 weeks, and 6 weeks using Arm functioning questionnaire. The QOL assessed at pre-treatment and 6 weeks using SF-36. The outcome data of experimental group was compared with control group (n=20). The collected data was analyzed by using SPSS 10.0 statistical program. The arm functioning of experimental group was increased from 2 weeks after (W=.224, p=.011) and statistically differenced with control group at 2 weeks (Z=-2.241, p=.024) and 6 weeks (Z=-2.453, p=.013). Physical function of QOL domain increased in experimental group (Z=-1.162, p=.050), also statistically differenced with control group (Z=-2.182, p= .030) at 6 weeks. The results suggest that the educational program of manual lymph massage can improve arm functioning and physical function of QOL domain in breast cancer patients with lymphedema.

Concentrations of indoor pollutants database: User's manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-05-01

This manual describes the computer-based database on indoor air pollutants. This comprehensive database alloys helps utility personnel perform rapid searches on literature related to indoor air pollutants. Besides general information, it provides guidance for finding specific information on concentrations of indoor air pollutants. The manual includes information on installing and using the database as well as a tutorial to assist the user in becoming familiar with the procedures involved in doing bibliographic and summary section searches. The manual demonstrates how to search for information by going through a series of questions that provide search parameters such as pollutants type, year,more » building type, keywords (from a specific list), country, geographic region, author's last name, and title. As more and more parameters are specified, the list of references found in the data search becomes smaller and more specific to the user's needs. Appendixes list types of information that can be input into the database when making a request. The CIP database allows individual utilities to obtain information on indoor air quality based on building types and other factors in their own service territory. This information is useful for utilities with concerns about indoor air quality and the control of indoor air pollutants. The CIP database itself is distributed by the Electric Power Software Center and runs on IBM PC-compatible computers.« less

Process Control Manual for Aerobic Biological Wastewater Treatment Facilities.

ERIC Educational Resources Information Center

Environmental Protection Agency, Washington, DC. Office of Water Programs.

This Environmental Protection Agency (EPA) publication is an operations manual for activated sludge and trickling filter wastewater treatment facilities. The stated purpose of the manual is to provide an on-the-job reference for operators of these two types of treatment plants. The overall objective of the manual is to aid the operator in…

Development of a short course : manual on uniform traffic control devices for the Alabama Department of Transportation

DOT National Transportation Integrated Search

2002-05-31

This project developed a one-day short course on the Manual on Uniform Manual Traffic Control Devices (MUTCD) for the Alabama Department of Transportation (ALDOT). Portions of the MUTCD are changed from time to time, and in 2001a significantly revise...

PDQ: Planning and Development of Quality Services in the Schools, Instructional Guide, Student Manual and Reference Materials.

ERIC Educational Resources Information Center

Wright, Sandra Raymore

The instructional guide, student manual, and reference materials were developed by the PDQ Project, Planning and Development of Quality Services in the Schools, an effort by the American Speech-Language-Hearing Association to provide public school personnel working with communication disordered children with information and training related to…

ENHANCED STREAM WATER QUALITY MODELS QUAL2E AND QUAL2E-UNCAS: DOCUMENTATION AND USER MANUAL

EPA Science Inventory

The manual is a major revision of the original QUAL2E program documentation released in 1985. It includes a description of the recent modifications and improvements to the widely used water quality models QUAL-II and QUAL2E. The enhancements include an extensive capability for un...

Water-quality assessment of south-central Texas : comparison of water quality in surface-water samples collected manually and by automated samplers

USGS Publications Warehouse

Ging, Patricia B.

1999-01-01

Surface-water sampling protocols of the U.S. Geological Survey National Water-Quality Assessment (NAWQA) Program specify samples for most properties and constituents to be collected manually in equal-width increments across a stream channel and composited for analysis. Single-point sampling with an automated sampler (autosampler) during storms was proposed in the upper part of the South-Central Texas NAWQA study unit, raising the question of whether property and constituent concentrations from automatically collected samples differ significantly from those in samples collected manually. Statistical (Wilcoxon signed-rank test) analyses of 3 to 16 paired concentrations for each of 26 properties and constituents from water samples collected using both methods at eight sites in the upper part of the study unit indicated that there were no significant differences in concentrations for dissolved constituents, other than calcium and organic carbon.

Development of Feedforward Control in a Dynamic Manual Tracking Task

ERIC Educational Resources Information Center

van Roon, Dominique; Caeyenberghs, Karen; Swinnen, Stephan P.; Smits-Engelsman, Bouwien C. M.

2008-01-01

To examine the development of feedforward control during manual tracking, 117 participants in 5 age groups (6 to 7, 8 to 9, 10 to 11, 12 to 14, and 15 to 17 years) tracked an accelerating dot presented on a monitor by moving an electronic pen on a digitizer. To remain successful at higher target velocities, they had to create a predictive model of…

The effect of manual therapy and exercise in patients with chronic low back pain: Double blind randomized controlled trial.

PubMed

Ulger, Ozlem; Demirel, Aynur; Oz, Müzeyyen; Tamer, Seval

2017-11-06

To determine the effects of spinal stabilization exercises (SSE) and manual therapy methods on pain, function and quality of life (QoL) levels in individuals with chronic low back pain (CLBP). A total of one-hundred thirteen patients diagnosed as CLBP were enrolled to the study. The patients allocated into Spinal Stabilization group (SG) and manual therapy group (MG), randomly. While SSE performed in SG, soft tissue mobilizations, muscle-energy techniques, joint mobilizations and manipulations were performed in MG. While the severity of pain was assessed with Visual Analog Scale (VAS), Oswestry Disability Index (ODI) and Short Form 36 (SF-36) assessments were performed to evaluate the functional status and QoL, respectively. All assessments were repeated before and after the treatment. Intragroup analyses both treatments were effective in terms of sub parameters of pain, function and life quality (p< 0.05). Inter group analyses, there was more reduction in pain and improvement in functional status in favor of MG (p< 0.05). This study showed that SSE and manual therapy methods have the same effects on QoL, while the manual treatment is more effective on the pain and functional parameters in particular.

Quality Control of Wind Data from 50-MHz Doppler Radar Wind Profiler

NASA Technical Reports Server (NTRS)

Vacek, Austin

2016-01-01

Upper-level wind profiles obtained from a 50-MHz Doppler Radar Wind Profiler (DRWP) instrument at Kennedy Space Center are incorporated in space launch vehicle design and day-of-launch operations to assess wind effects on the vehicle during ascent. Automated and manual quality control (QC) techniques are implemented to remove spurious data in the upper-level wind profiles caused from atmospheric and non-atmospheric artifacts over the 2010-2012 period of record (POR). By adding the new quality controlled profiles with older profiles from 1997-2009, a robust database will be constructed of upper-level wind characteristics. Statistical analysis will determine the maximum, minimum, and 95th percentile of the wind components from the DRWP profiles over recent POR and compare against the older database. Additionally, this study identifies specific QC flags triggered during the QC process to understand how much data is retained and removed from the profiles.

Quality Control of Wind Data from 50-MHz Doppler Radar Wind Profiler

NASA Technical Reports Server (NTRS)

Vacek, Austin

2015-01-01

Upper-level wind profiles obtained from a 50-MHz Doppler Radar Wind Profiler (DRWP) instrument at Kennedy Space Center are incorporated in space launch vehicle design and day-of-launch operations to assess wind effects on the vehicle during ascent. Automated and manual quality control (QC) techniques are implemented to remove spurious data in the upper-level wind profiles caused from atmospheric and non-atmospheric artifacts over the 2010-2012 period of record (POR). By adding the new quality controlled profiles with older profiles from 1997-2009, a robust database will be constructed of upper-level wind characteristics. Statistical analysis will determine the maximum, minimum, and 95th percentile of the wind components from the DRWP profiles over recent POR and compare against the older database. Additionally, this study identifies specific QC flags triggered during the QC process to understand how much data is retained and removed from the profiles.

Safe, Effective Use of Pesticides, A Manual for Commercial Applicators: Fruit Pest Control.

ERIC Educational Resources Information Center

Brunner, J.; And Others

This manual is intended to assist pesticide applicators prepare for certification under the Michigan Pesticide Control Act of 1976. The primary focus of this publication is on fruit pest control. Sections included are: (1) Causes of fruit diseases; (2) Fruit fungicides and bactericides; (3) Insect and mite pests; (4) Insecticides and miticides;…

PROCESS DESIGN MANUAL: NITROGEN CONTROL

EPA Science Inventory

This manual is an update and revision of the original 1975 edition. Given the experience of the past 18 years, the focus of this edition is directed to those biological/mechanical systems that have found widespread use for nitrification and nitrogen,removal. The primary audience ...

Navy Occupational Health Information Management System (NOHIMS). Hazardous Materials Control Module. Users’ Manual

DTIC Science & Technology

1987-01-16

Occupational Health Information Management System (NOHIMS) 6 Hazardous Materials Control Module (HMC) User’s Manual 7. Author(s) 8. Performing Organization...Materials Control (HMC) module of the Naval Medical Command’s (NAVMED) Navy Occupational Health Information Management System (NOHIMS). After presenting

Highway Safety Program Manual: Volume 16: Debris Hazard Control and Cleanup.

ERIC Educational Resources Information Center

National Highway Traffic Safety Administration (DOT), Washington, DC.

Volume 16 of the 19-volume Highway Safety Program Manual (which provides guidance to State and local governments on preferred highway safety practices) concentrates on debris hazard control and cleanup. The purpose and objectives of such a program are outlined. Federal authority in the area of highway safety and policies regarding a debris control…

76 FR 46213 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-02

... design and application of traffic control devices, this Manual should not be considered a substitute for... retroreflectivity of longitudinal pavement markings. The deadline for comments to that docket has passed and the... the proposed revisions regarding maintaining minimum retroreflectivity of longitudinal pavement...

The Effectiveness of Manual Therapy for Relieving Pain, Stiffness, and Dysfunction in Knee Osteoarthritis: A Systematic Review and Meta-Analysis.

PubMed

Xu, Qinguang; Chen, Bei; Wang, Yueyi; Wang, Xuezong; Han, Dapeng; Ding, Daofang; Zheng, Yuxin; Cao, Yuelong; Zhan, Hongsheng; Zhou, Yao

2017-05-01

Knee osteoarthritis (KOA) is the most common form of arthritis, leading to pain disability in seniors and increased health care utilization. Manual therapy is one widely used physical treatment for KOA. To evaluate the effectiveness and adverse events (AEs) of manual therapy compared to other treatments for relieving pain, stiffness, and physical dysfunction in patients with KOA. A systematic review and meta-analysis of manual therapy for KOA. We searched PubMed, EMBASE, the Cochrane Library, and Chinese databases for relevant randomized controlled trials (RCTs) of manual therapy for patients with KOA from the inception to October 2015 without language restrictions. RCTs compared manual therapy to the placebo or other interventional control with an appropriate description of randomization. Two reviewers independently conducted the search results identification, data extraction, and methodological quality assessment. The methodological quality was assessed by PEDro scale. Pooled data was expressed as standard mean difference (SMD), with 95% confident intervals (CIs) in a random effects model. The meta-analysis of manual therapy for KOA on pain, stiffness, and physical function were conducted. Fourteen studies involving 841 KOA participants compared to other treatments were included. The methodological quality of most included RCTs was poor. The mean PEDro scale score was 6.6. The meta-analyses results showed that manual therapy had statistically significant effects on relieving pain (standardized mean difference, SMD = -0.61, 95% CI -0.95 to -0.28, P = 76%), stiffness (SMD = -0.58, 95% CI -0.95 to -0.21, P = 81%), improving physical function (SMD = -0.49, 95% CI -0.76 to -0.22, P = 65%), and total score (SMD = -0.56, 95% CI -0.78 to -0.35, P = 50%). But in the subgroups, manual therapy did not show significant improvements on stiffness and physical function when treatment duration was less than 4 weeks. And the long-term information for manual therapy was

Manual therapy in adults with tension-type headache: A systematic review.

PubMed

Cumplido-Trasmonte, C; Fernández-González, P; Alguacil-Diego, I M; Molina-Rueda, F

2018-03-07

Tension-type headache is the most common primary headache, with a high prevalence and a considerable socioeconomic impact. Manual physical therapy techniques are widely used in the clinical field to treat the symptoms associated with tension-type headache. This systematic review aims to determine the effectiveness of manual and non-invasive therapies in the treatment of patients with tension-type headache. We conducted a systematic review of randomised controlled trials in the following databases: Brain, PubMed, Web of Science, PEDro, Scopus, CINAHL, and Science Direct. Ten randomised controlled trials were included for analysis. According to these studies, manual therapy improves symptoms, increasing patients' well-being and improving the outcome measures analysed. Manual therapy has positive effects on pain intensity, pain frequency, disability, overall impact, quality of life, and craniocervical range of motion in adults with tension-type headache. None of the techniques was found to be superior to the others; combining different techniques seems to be the most effective approach. Copyright © 2018 Sociedad Española de Neurología. Publicado por Elsevier España, S.L.U. All rights reserved.

Annual Conference on Manual Control (20th) Held in California on June 12 - 14, 1984. Volume 1

DTIC Science & Technology

1984-06-14

and in conjunction with movements of other joints. Much of this data is for atheletic performance . Components of such data can be simulated using JAMM... PERFORMANCE Chairman: Mr. Henry Jex Jewell, W. & Clement, W.F. A method for measuring the effective throughput time delay in simulated displays involving...manual control. 173 Allen, R. W. & DiMarco, R. J. Effects of transport delays on manual control system performance . 185 Sanders, K. E., Anderson, D. C

Clinical Practice Guideline Development Manual, Third Edition: a quality-driven approach for translating evidence into action.

PubMed

Rosenfeld, Richard M; Shiffman, Richard N; Robertson, Peter

2013-01-01

Guidelines translate best evidence into best practice. A well-crafted guideline promotes quality by reducing health care variations, improving diagnostic accuracy, promoting effective therapy, and discouraging ineffective-or potentially harmful-interventions. Despite a plethora of published guidelines, methodology is often poorly defined and varies greatly within and among organizations. The third edition of this manual describes the principles and practices used successfully by the American Academy of Otolaryngology--Head and Neck Surgery Foundation to produce quality-driven, evidence-based guidelines using efficient and transparent methodology for actionable recommendations with multidisciplinary applicability. The development process emphasizes a logical sequence of key action statements supported by amplifying text, action statement profiles, and recommendation grades linking action to evidence. New material in this edition includes standards for trustworthy guidelines, updated classification of evidence levels, increased patient and public involvement, assessing confidence in the evidence, documenting differences of opinion, expanded discussion of conflict of interest, and use of computerized decision support for crafting actionable recommendations. As clinical practice guidelines become more prominent as a key metric of quality health care, organizations must develop efficient production strategies that balance rigor and pragmatism. Equally important, clinicians must become savvy in understanding what guidelines are--and are not--and how they are best used to improve care. The information in this manual should help clinicians and organizations achieve these goals.

Preharvest manual herbicide treatments for controlling American beech in Central West Virginia

Treesearch

Jeffery D. Kochenderfer; James N. Kochenderfer; David A. Warner; Gary W. Miller

2004-01-01

Application costs and efficacy were determined for manual preharvest herbicide treatments applied to control American beech (Fagus grandifolia Ehrh.) that was interfering with the establishment and development of black cherry (Prunus serotina Ehrh.) in central West Virginia. The treatments consisted of four levels of basal area...

Design and control of electromagnetic clutch actuation system for automated manual transmission

NASA Astrophysics Data System (ADS)

Ranjan, Ashish; Prasanth, S.; Cherian, Fenin; Baskar, P.

2017-11-01

There is a growing interest towards Automatic Transmission in India as it provides better comfort and drivability. But the high cost of this system is limiting itself to be successful in the Indian markets. Due to this, Automated Manual Transmission (AMT) is considered which provides a better solution towards automation as it enhances the drivability and fuel consumption characteristics of a manual transmission at lower costs. However, torque lag and comfort are major issues with AMT which can be addressed by reducing the shift time. In this paper we describe an Electromagnetic Linear Clutch Actuator as a replacement to current electrohydraulic and electromechanical actuator. A control system for the actuator is presented and a clutch engagement strategy is also implemented which reduces the engagement time to 0.78 seconds while reducing jerk and torque lag. The actuator and control system is simulated on a MATLAB Simulink and agreeable results have been obtained.

Real-Time Performance Feedback for the Manual Control of Spacecraft

NASA Astrophysics Data System (ADS)

Karasinski, John Austin

Real-time performance metrics were developed to quantify workload, situational awareness, and manual task performance for use as visual feedback to pilots of aerospace vehicles. Results from prior lunar lander experiments with variable levels of automation were replicated and extended to provide insights for the development of real-time metrics. Increased levels of automation resulted in increased flight performance, lower workload, and increased situational awareness. Automated Speech Recognition (ASR) was employed to detect verbal callouts as a limited measure of subjects' situational awareness. A one-dimensional manual tracking task and simple instructor-model visual feedback scheme was developed. This feedback was indicated to the operator by changing the color of a guidance element on the primary flight display, similar to how a flight instructor points out elements of a display to a student pilot. Experiments showed that for this low-complexity task, visual feedback did not change subject performance, but did increase the subjects' measured workload. Insights gained from these experiments were applied to a Simplified Aid for EVA Rescue (SAFER) inspection task. The effects of variations of an instructor-model performance-feedback strategy on human performance in a novel SAFER inspection task were investigated. Real-time feedback was found to have a statistically significant effect of improving subject performance and decreasing workload in this complicated four degree of freedom manual control task with two secondary tasks.

Validation of Placebo in a Manual Therapy Randomized Controlled Trial

PubMed Central

Chaibi, Aleksander; Šaltytė Benth, Jūratė; Bjørn Russell, Michael

2015-01-01

At present, no consensus exists among clinical and academic experts regarding an appropriate placebo for randomized controlled trials (RCTs) of spinal manipulative therapy (SMT). Therefore, we investigated whether it was possible to conduct a chiropractic manual-therapy RCT with placebo. Seventy migraineurs were randomized to a single-blinded placebo-controlled clinical trial that consisted of 12 treatment sessions over 3 months. The participants were randomized to chiropractic SMT or placebo (sham manipulation). After each session, the participants were surveyed on whether they thought they had undergone active treatment (“yes” or “no”) and how strongly they believed that active treatment was received (numeric rating scale 0–10). The outcome measures included the rate of successful blinding and the certitude of the participants’ beliefs in both treatment groups. At each treatment session, more than 80% of the participants believed that they had undergone active treatment, regardless of group allocation. The odds ratio for believing that active treatment was received was >10 for all treatment sessions in both groups (all p < 0.001). The blinding was maintained throughout the RCT. Our results strongly demonstrate that it is possible to conduct a single-blinded manual-therapy RCT with placebo and to maintain the blinding throughout 12 treatment sessions given over 3 months. PMID:26145718

Thoracic manual therapy is not more effective than placebo thoracic manual therapy in patients with shoulder dysfunctions: A systematic review with meta-analysis.

PubMed

Bizzarri, Paolo; Buzzatti, Luca; Cattrysse, Erik; Scafoglieri, Aldo

2018-02-01

Manual treatments targeting different regions (shoulder, cervical spine, thoracic spine, ribs) have been studied to deal with patients complaining of shoulder pain. Thoracic manual treatments seem able to produce beneficial effects on this group of patients. However, it is not clear whether the patient improvement is a consequence of thoracic manual therapy or a placebo effect. To compare the efficacy of thoracic manual therapy and placebo thoracic manual treatment for patients with shoulder dysfunction. Electronic databases (MEDLINE, CENTRAL, PEDro, CINAHL, WoS, EMBASE, ERIC) were searched through November 2016. Randomized Controlled Trials assessing pain, mobility and function were selected. The Cochrane bias estimation tool was applied. Outcome results were either extracted or computed from raw data. Meta-analysis was performed for outcomes with low heterogeneity. Four studies were included in the review. The methodology of the included studies was generally good except for one study that was rated as high risk of bias. Meta-analysis showed no significant effect for "pain at present" (SMD -0.02; 95% CI: -0.35, 0.32) and "pain during movement" (SMD -0.12; 95% CI: -0.45, 0.21). There is very low to low quality of evidence that a single session of thoracic manual therapy is not more effective than a single session of placebo thoracic manual therapy in patients with shoulder dysfunction at immediate post-treatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Twelfth Annual Conference on Manual Control

NASA Technical Reports Server (NTRS)

Wempe, T. E.

1976-01-01

Main topics discussed cover multi-task decision making, attention allocation and workload measurement, displays and controls, nonvisual displays, tracking and other psychomotor tasks, automobile driving, handling qualities and pilot ratings, remote manipulation, system identification, control models, and motion and visual cues. Sixty-five papers are included with presentations on results of analytical studies to develop and evaluate human operator models for a range of control task, vehicle dynamics and display situations; results of tests of physiological control systems and applications to medical problems; and on results of simulator and flight tests to determine display, control and dynamics effects on operator performance and workload for aircraft, automobile, and remote control systems.

The effectiveness and cost-evaluation of manual therapy and physical therapy in patients with sub-acute and chronic non specific neck pain. Rationale and design of a Randomized Controlled Trial (RCT)

PubMed Central

2010-01-01

Background Manual Therapy applied to patients with non specific neck pain has been investigated several times. In the Netherlands, manual therapy as applied according to the Utrecht School of Manual Therapy (MTU) has not been the subject of a randomized controlled trial. MTU differs in diagnoses and treatment from other forms of manual therapy. Methods/Design This is a single blind randomized controlled trial in patients with sub-acute and chronic non specific neck pain. Patients with neck complaints existing for two weeks (minimum) till one year (maximum) will participate in the trial. 180 participants will be recruited in thirteen primary health care centres in the Netherlands. The experimental group will be treated with MTU during a six week period. The control group will be treated with physical therapy (standard care, mainly active exercise therapy), also for a period of six weeks. Primary outcomes are Global Perceived Effect (GPE) and functional status (Neck Disability Index (NDI-DV)). Secondary outcomes are neck pain (Numeric Rating Scale (NRS)), Eurocol, costs and quality of life (SF36). Discussion This paper presents details on the rationale of MTU, design, methods and operational aspects of the trial. Trial registration ClinicalTrials.gov Identifier: NCT00713843 PMID:20096136

Manual control aspects of orbital flight

NASA Technical Reports Server (NTRS)

Brody, Adam R.

1990-01-01

Studies of spacecraft rendezvous and docking operations began in the Gemini program in preparation for the two dockings required to send a crew to the moon and return them safely to Earth. However, the goal of getting to the moon before the end of the decade was of greater concern than mission optimization so little or no time or money was expended in researching human factors implications of operational aspects such as braking gates or control modes. Also, with sixteen operational dockings over a six year period (12 Apollo, 3 Skylab, and 1 ASTP) in the United States space program, economies of scale were not yet available to justify extensive research into decreasing the time or fuel necessary for a successful docking. With an operational space station era approaching in which orbital maneuvering vehicle (OMV), orbital transfer vehicle (OTV), shuttle orbiter, and other traffic will play a major role, a concerted research effort now could help avoid many potential problems later in addition to increasing safety, fuel economy, and productivity. A knowledge of manual control capabilities associated with piloted spaceflight could help save a life if the operational flight envelope can be safely enlarged to include faster dockings that currently envisioned. For example, current and future research is designed to acquire the appropriate information.

Concentrations of indoor pollutants database: User`s manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-05-01

This manual describes the computer-based database on indoor air pollutants. This comprehensive database alloys helps utility personnel perform rapid searches on literature related to indoor air pollutants. Besides general information, it provides guidance for finding specific information on concentrations of indoor air pollutants. The manual includes information on installing and using the database as well as a tutorial to assist the user in becoming familiar with the procedures involved in doing bibliographic and summary section searches. The manual demonstrates how to search for information by going through a series of questions that provide search parameters such as pollutants type, year,more » building type, keywords (from a specific list), country, geographic region, author`s last name, and title. As more and more parameters are specified, the list of references found in the data search becomes smaller and more specific to the user`s needs. Appendixes list types of information that can be input into the database when making a request. The CIP database allows individual utilities to obtain information on indoor air quality based on building types and other factors in their own service territory. This information is useful for utilities with concerns about indoor air quality and the control of indoor air pollutants. The CIP database itself is distributed by the Electric Power Software Center and runs on IBM PC-compatible computers.« less

Manual Throttles-Only Control Effectivity for Emergency Flight Control of Transport Aircraft

NASA Technical Reports Server (NTRS)

Stevens, Richard; Burcham, Frank W., Jr.

2009-01-01

If normal aircraft flight controls are lost, emergency flight control may be attempted using only the thrust of engines. Collective thrust is used to control flightpath, and differential thrust is used to control bank angle. One issue is whether a total loss of hydraulics (TLOH) leaves an airplane in a recoverable condition. Recoverability is a function of airspeed, altitude, flight phase, and configuration. If the airplane can be recovered, flight test and simulation results on several transport-class airplanes have shown that throttles-only control (TOC) is usually adequate to maintain up-and-away flight, but executing a safe landing is very difficult. There are favorable aircraft configurations, and also techniques that will improve recoverability and control and increase the chances of a survivable landing. The DHS and NASA have recently conducted a flight and simulator study to determine the effectivity of manual throttles-only control as a way to recover and safely land a range of transport airplanes. This paper discusses TLOH recoverability as a function of conditions, and TOC landability results for a range of transport airplanes, and some key techniques for flying with throttles and making a survivable landing. Airplanes evaluated include the B-747, B-767, B-777, B-757, A320, and B-737 airplanes.

Turtle Manual.

ERIC Educational Resources Information Center

Schneider, Marlene; Robin, Arthur

This manual describes the Turtle Technique which was developed to help children with behavior problems control their own disruptive behavior. The technique differs from other behavior modification techniques in that it is based upon self-control rather than external control of disruptive behavior. The Turtle Technique first teaches the child how…

Comparison of pressure-controlled provocation discography using automated versus manual syringe pump manometry in patients with chronic low back pain.

PubMed

Derby, Richard; Lee, Sang Hoon; Lee, Jeong-Eun; Lee, Sang-Heon

2011-01-01

The study compares the rate of positive discograms using an automated versus a manual pressure-controlled injection devise and compares the pressure and volume values at various pressures and initial evoked pain and 6/10 or greater evoked pain. A retrospective study prospectively collected patient study data used in a prior prospective study and with prospectively collected data which is routinely collected per our institutional standardized audit protocol. Two custom-built disc manometers (automated injection speed control; manual injection speed control) were sequentially employed during provocation discography in 510 discs of 151 consecutive patients. Two hundred thirty-seven discs of 67 patients with chronic low back pain were evaluated using the automated manometer (automated group) and 273 discs of 84 patients were evaluated with a manual manometer (manual group). No significant differences in positive discogram rates were found between the automated and manual groups (32.1% vs 32.6% per disc, respectively, P>0.05). No significant differences in low-pressure positive discogram rates were found (16.0% vs 15.0% per disc, automated group versus manual group, respectively, P>0.05). However, there were significantly increased volumes and lower pressures at initial and "bad" pain provocation. The study results found equivalent positive discogram rates following a series of pressure-controlled discography using either an automated or manual pressure devise. There were, however significant increases in volume at both initial onset of evoked pain and at 6/10 pain when using the automated injection devise that may have caused the observed lower opening pressure and lower pressure values at initial evoked pain. Assuming increased volumes are innocuous, automated injection is inherently more controlled and may better reduce unintended and often unrecorded spurious high dynamic pressure peaks thereby reducing conscious and unconscious operator bias. Wiley Periodicals, Inc.

Value Engineering. Technical Manual. School Facilities Development Procedures Manual.

ERIC Educational Resources Information Center

Washington Office of the State Superintendent of Public Instruction, Olympia.

Value Engineering (VE) is a cost-optimizing technique used to analyze design quality and cost-effectiveness. The application of VE procedures to the design and construction of school facilities has been adopted by the state of Washington. This technical manual provides guidance in developing the scope and applicability of VE to school projects; in…

Manual Control Age and Sex Differences in 4 to 11 Year Old Children

PubMed Central

Flatters, Ian; Hill, Liam J. B.; Williams, Justin H. G.; Barber, Sally E.; Mon-Williams, Mark

2014-01-01

To what degree does being male or female influence the development of manual skills in pre-pubescent children? This question is important because of the emphasis placed on developing important new manual skills during this period of a child's education (e.g. writing, drawing, using computers). We investigated age and sex-differences in the ability of 422 children to control a handheld stylus. A task battery deployed using tablet PC technology presented interactive visual targets on a computer screen whilst simultaneously recording participant's objective kinematic responses, via their interactions with the on-screen stimuli using the handheld stylus. The battery required children use the stylus to: (i) make a series of aiming movements, (ii) trace a series of abstract shapes and (iii) track a moving object. The tasks were not familiar to the children, allowing measurement of a general ability that might be meaningfully labelled ‘manual control’, whilst minimising culturally determined differences in experience (as much as possible). A reliable interaction between sex and age was found on the aiming task, with girls' movement times being faster than boys in younger age groups (e.g. 4–5 years) but with this pattern reversing in older children (10–11 years). The improved performance in older boys on the aiming task is consistent with prior evidence of a male advantage for gross-motor aiming tasks, which begins to emerge during adolescence. A small but reliable sex difference was found in tracing skill, with girls showing a slightly higher level of performance than boys irrespective of age. There were no reliable sex differences between boys and girls on the tracking task. Overall, the findings suggest that prepubescent girls are more likely to have superior manual control abilities for performing novel tasks. However, these small population differences do not suggest that the sexes require different educational support whilst developing their manual skills

Safe, Effective Use of Pesticides, A Manual for Commercial Applicators: Home, Institutional, and Structural Pest Control.

ERIC Educational Resources Information Center

Extension Service (USDA), Washington, DC.

This manual is designed to assist pest control operators to prepare for certification under the Michigan Pesticide Control Act of 1976. The primary focus of this publication is on home, institutional, and structural pest control. The ten sections included describe: (1) Insect control; (2) Rodent control; (3) Special situation pest control; (4)…

Effective teaching of manual skills to physiotherapy students: a randomised clinical trial.

PubMed

Rossettini, Giacomo; Rondoni, Angie; Palese, Alvisa; Cecchetto, Simone; Vicentini, Marco; Bettale, Fernanda; Furri, Laura; Testa, Marco

2017-08-01

To date, despite the relevance of manual skills laboratories in physiotherapy education, evidence on the effectiveness of different teaching methods is limited. Peyton's four-step and the 'See one, do one' approaches were compared for their effectiveness in teaching manual skills. A cluster randomised controlled trial was performed among final-year, right-handed physiotherapy students, without prior experience in manual therapy or skills laboratories. The manual technique of C1-C2 passive right rotation was taught by different experienced physiotherapist using Peyton's four-step approach (intervention group) and the 'See one, do one' approach (control group). Participants, teachers and assessors were blinded to the aims of the study. Primary outcomes were quality of performance at the end of the skills laboratories, and after 1 week and 1 month. Secondary outcomes were time required to teach, time required to perform the procedure and student satisfaction. A total of 39 students were included in the study (21 in the intervention group and 18 in the control group). Their main characteristics were homogeneous at baseline. The intervention group showed better quality of performance in the short, medium and long terms (F 1,111  = 35.91, p < 0.001). Both groups demonstrated decreased quality of performance over time (F 2,111  = 12.91, p < 0.001). The intervention group reported significantly greater mean ± standard deviation satisfaction (4.31 ± 1.23) than the control group (4.03 ± 1.31) (p < 0.001). Although there was no significant difference between the two methods in the time required for teaching, the time required by the intervention group to perform the procedure was significantly lower immediately after the skills laboratories and over time (p < 0.001). Peyton's four-step approach is more effective than the 'See one, do one' approach in skills laboratories aimed at developing physiotherapy student competence in C1-C2 passive mobilisation

Massage, reflexology and other manual methods for pain management in labour.

PubMed

Smith, Caroline A; Levett, Kate M; Collins, Carmel T; Dahlen, Hannah G; Ee, Carolyn C; Suganuma, Machiko

2018-03-28

Many women would like to avoid pharmacological or invasive methods of pain management in labour, and this may contribute towards the popularity of complementary methods of pain management. This review examined the evidence currently available on manual methods, including massage and reflexology, for pain management in labour. This review is an update of the review first published in 2012. To assess the effect, safety and acceptability of massage, reflexology and other manual methods to manage pain in labour. For this update, we searched Cochrane Pregnancy and Childbirth's Trials Register (30 June 2017), the Cochrane Central Register of Controlled Trials (CENTRAL; 2017, Issue 6), MEDLINE (1966 to 30 June 2017, CINAHL (1980 to 30 June 2017), the Australian New Zealand Clinical Trials Registry (4 August 2017), Chinese Clinical Trial Registry (4 August 2017), ClinicalTrials.gov, (4 August 2017), the National Center for Complementary and Integrative Health (4 August 2017), the WHO International Clinical Trials Registry Platform (ICTRP) (4 August 2017) and reference lists of retrieved trials. We included randomised controlled trials comparing manual methods with standard care, other non-pharmacological forms of pain management in labour, no treatment or placebo. We searched for trials of the following modalities: massage, warm packs, thermal manual methods, reflexology, chiropractic, osteopathy, musculo-skeletal manipulation, deep tissue massage, neuro-muscular therapy, shiatsu, tuina, trigger point therapy, myotherapy and zero balancing. We excluded trials for pain management relating to hypnosis, aromatherapy, acupuncture and acupressure; these are included in other Cochrane reviews. Two review authors independently assessed trial quality, extracted data and checked data for accuracy. We contacted trial authors for additional information. We assessed the quality of the evidence using the GRADE approach. We included a total of 14 trials; 10 of these (1055 women

Safe, Effective Use of Pesticides, A Manual for Commercial Applicators: Public Health Pest Control.

ERIC Educational Resources Information Center

Extension Service (USDA), Washington, DC.

This manual is designed to assist public health pest control officials in meeting the certification required under the Michigan Pesticide Control Act of 1976. The four sections included describe: (1) Insects of public health significance in Michigan; (2) Other arthropods that affect man; (3) Swimmers' itch parasite and snail host; and (4)…

Manual therapy in addition to physiotherapy does not improve clinical or economic outcomes after ankle fracture.

PubMed

Lin, Chung-Wei Christine; Moseley, Anne M; Haas, Marion; Refshauge, Kathryn M; Herbert, Robert D

2008-06-01

The primary aim of this study was to determine the effectiveness and cost-effectiveness of adding manual therapy to a physiotherapy programme for ankle fracture. Assessor-blinded randomized controlled trial. Ninety-four adults were recruited within one week of cast removal for isolated ankle fracture. Inclusion criteria were: they were able to weight-bear as tolerated or partial weight-bear, were referred for physiotherapy, and experienced pain. Ninety-one participants completed the study. Participants were randomly allocated to receive manual therapy (anterior-posterior joint mobilization over the talus) plus a standard physiotherapy programme (experimental), or the standard physiotherapy programme only (control). They were assessed by a blinded assessor at baseline, and at 4, 12 and 24 weeks. The main outcomes were activity limitation and quality of life. Information on costs and healthcare utilization was collected every 4 weeks up to 24 weeks. There were no clinically worthwhile differences in activity limitation or quality of life between groups at any time-point. There was also no between-group difference in quality-adjusted life-years, but the experimental group incurred higher out-of-pocket costs (mean between-group difference = AU$200, 95% confidence interval 26-432). When provided in addition to a physiotherapy programme, manual therapy did not enhance outcome in adults after ankle fracture.

Safe, Effective Use of Pesticides, A Manual for Commercial Applicators: Ornamental and Turf Pest Control.

ERIC Educational Resources Information Center

Extension Service (USDA), Washington, DC.

This manual is intended to assist pesticide applicators in the area of ornamental and turf pest control prepare for certification under the Michigan Pesticide Control Act of 1976. The three sections presented describe: (1) Ornamentals; (2) Turfgrass; and (3) Pest Control. Section one discusses the diagnostic chart for plant problems, non-pest…

Launch Vehicle Manual Steering with Adaptive Augmenting Control In-flight Evaluations of Adverse Interactions Using a Piloted Aircraft

NASA Technical Reports Server (NTRS)

Hanson, Curt; Miller, Chris; Wall, John H.; Vanzwieten, Tannen S.; Gilligan, Eric; Orr, Jeb S.

2015-01-01

An adaptive augmenting control algorithm for the Space Launch System has been developed at the Marshall Space Flight Center as part of the launch vehicles baseline flight control system. A prototype version of the SLS flight control software was hosted on a piloted aircraft at the Armstrong Flight Research Center to demonstrate the adaptive controller on a full-scale realistic application in a relevant flight environment. Concerns regarding adverse interactions between the adaptive controller and a proposed manual steering mode were investigated by giving the pilot trajectory deviation cues and pitch rate command authority. Two NASA research pilots flew a total of twenty five constant pitch-rate trajectories using a prototype manual steering mode with and without adaptive control.

Quality Leadership and Quality Control

PubMed Central

Badrick, Tony

2003-01-01

Different quality control rules detect different analytical errors with varying levels of efficiency depending on the type of error present, its prevalence and the number of observations. The efficiency of a rule can be gauged by inspection of a power function graph. Control rules are only part of a process and not an end in itself; just as important are the trouble-shooting systems employed when a failure occurs. 'Average of patient normals' may develop as a usual adjunct to conventional quality control serum based programmes. Acceptable error can be based on various criteria; biological variation is probably the most sensible. Once determined, acceptable error can be used as limits in quality control rule systems. A key aspect of an organisation is leadership, which links the various components of the quality system. Leadership is difficult to characterise but its key aspects include trust, setting an example, developing staff and critically setting the vision for the organisation. Organisations also have internal characteristics such as the degree of formalisation, centralisation, and complexity. Medical organisations can have internal tensions because of the dichotomy between the bureaucratic and the shadow medical structures. PMID:18568046

Principles and Practices for Quality Assurance and Quality Control

USGS Publications Warehouse

Jones, Berwyn E.

1999-01-01

Quality assurance and quality control are vital parts of highway runoff water-quality monitoring projects. To be effective, project quality assurance must address all aspects of the project, including project management responsibilities and resources, data quality objectives, sampling and analysis plans, data-collection protocols, data quality-control plans, data-assessment procedures and requirements, and project outputs. Quality control ensures that the data quality objectives are achieved as planned. The historical development and current state of the art of quality assurance and quality control concepts described in this report can be applied to evaluation of data from prior projects.

Iowa Commercial Pesticide Applicator Manual, Category 5: Aquatic Pest Control. CS-17.

ERIC Educational Resources Information Center

Jennings, Vivan M.; Ryan, Stephen O.

This manual provides information needed to meet specific standards for certification as a pesticide applicator. The text is concerned with the control of aquatic weeds in a variety of water use situations, i.e. static water, limited-flow impoundments and moving water. Also discussed are the principles of limited area application such as surface or…

Domestic Rodent Control Training Manual: A Training Aid for the Rodent Control Category for Certification of Pesticide Applicators.

ERIC Educational Resources Information Center

Childress, William R., Jr.; And Others

This training manual, designed for training applicants who wish to obtain certification in pesticide application relative to rodent control, covers the following topics: economic factors, public health factors, biological characteristics of domestic rodents, rat and mouse signs, trapping, repellents, poisons, baits, poisoned water, dumps, sewers,…

DFLOW USER'S MANUAL

EPA Science Inventory

DFLOW is a computer program for estimating design stream flows for use in water quality studies. The manual describes the use of the program on both the EPA's IBM mainframe system and on a personal computer (PC). The mainframe version of DFLOW can extract a river's daily flow rec...

[Efficient document management by introduction of a new, dynamic quality manual application according to DIN EN ISO 9001:2000].

PubMed

Pache, G; Saueressig, U; Baumann, T; Dürselen, L; Langer, M; Kotter, E

2008-06-01

Evaluation of the impact of a new, dynamic computer-aided quality manual application (QMA) regarding the acceptance and efficiency of a quality management system (QMS) according to DIN EN ISO 9001:2000. The QMA combines static pages of HTML with active content generated from an underlying database. Through user access rights, a hierarchy is defined to create and administer quality documents. Document workflow, feedback management and employee survey were analyzed to compare the performance of the new QMH with the formerly used static version. Integration of a document editor and automated document re-approval accelerated the document process by an average of 10 min. In spite of an increase of the yearly document changes of 60%, the administration effort was reduced by approximately 160 h. Integration of the feedback management system into the QMA decreased handling time from an average of 16.5 to 3.4 days. Simultaneously the number of feedback messages increased from 160 in 2005 to 306 in 2006. Employee satisfaction was raised (old: 3.19+/-1.02, new: 1.91+/-0.8). The number of users who partook in the QMA more than once a week also increased from 29.5% to 60%. The computer-aided quality manual application constitutes the basis for the success of our QMS. The possibility to actively participate in the quality management process has led to broad acceptance and usage by the employees. The administration effort was able to be tremendously decreased as compared to conventional QMS.

An International Coordinated Effort to Further the Documentation & Development of Quality Assurance, Quality Control, and Best Practices for Oceanographic Observations

NASA Astrophysics Data System (ADS)

Bushnell, M.; Waldmann, C.; Hermes, J.; Tamburri, M.

2017-12-01

Many oceanographic observation groups create and maintain QA, QC, and best practices (BP) to ensure efficient and accurate data collection and quantify quality. Several entities - IOOS® QARTOD, AtlantOS, ACT, WMO/IOC JCOMM OCG - have joined forces to document existing practices, identify gaps, and support development of emerging techniques. While each group has a slightly different focus, many underlying QA/QC/BP needs can be quite common. QARTOD focuses upon real-time data QC, and has produced manuals that address QC tests for eleven ocean variables. AtlantOS is a research and innovation project working towards the integration of ocean-observing activities across all disciplines in the Atlantic Basin. ACT brings together research institutions, resource managers, and private companies to foster the development and adoption of effective and reliable sensors for coastal, freshwater, and ocean environments. JCOMM promotes broad international coordination of oceanographic and marine meteorological observations and data management and services. Leveraging existing efforts of these organizations is an efficient way to consolidate available information, develop new practices, and evaluate the use of ISO standards to judge the quality of measurements. ISO standards may offer accepted support for a framework for an ocean data quality management system, similar to the meteorological standards defined by WMO (https://www.wmo.int/pages/prog/arep/gaw/qassurance.html). We will first cooperatively develop a plan to create a QA/QC/BP manual. The resulting plan will describe the need for such a manual, the extent of the manual, the process used to engage the community in creating it, the maintenance of the resultant document, and how these things will be done. It will also investigate standards for metadata. The plan will subsequently be used to develop the QA/QC/BP manual, providing guidance which advances the standards adopted by IOOS, AtlantOS, JCOMM, and others.

User’s manual to update the National Wildlife Refuge System Water Quality Information System (WQIS)

USGS Publications Warehouse

Chojnacki, Kimberly A.; Vishy, Chad J.; Hinck, Jo Ellen; Finger, Susan E.; Higgins, Michael J.; Kilbride, Kevin

2013-01-01

National Wildlife Refuges may have impaired water quality resulting from historic and current land uses, upstream sources, and aerial pollutant deposition. National Wildlife Refuge staff have limited time available to identify and evaluate potential water quality issues. As a result, water quality–related issues may not be resolved until a problem has already arisen. The National Wildlife Refuge System Water Quality Information System (WQIS) is a relational database developed for use by U.S. Fish and Wildlife Service staff to identify existing water quality issues on refuges in the United States. The WQIS database relies on a geospatial overlay analysis of data layers for ownership, streams and water quality. The WQIS provides summary statistics of 303(d) impaired waters and total maximum daily loads for the National Wildlife Refuge System at the national, regional, and refuge level. The WQIS allows U.S. Fish and Wildlife Service staff to be proactive in addressing water quality issues by identifying and understanding the current extent and nature of 303(d) impaired waters and subsequent total maximum daily loads. Water quality data are updated bi-annually, making it necessary to refresh the WQIS to maintain up-to-date information. This manual outlines the steps necessary to update the data and reports in the WQIS.

No-cost manual method for preparation of tissue microarrays having high quality comparable to semiautomated methods.

PubMed

Foda, Abd Al-Rahman Mohammad

2013-05-01

Manual tissue microarray (TMA) construction had been introduced to avoid the high cost of automated and semiautomated techniques. The cheapest and simplest technique for constructing manual TMA was that of using mechanical pencil tips. This study was carried out to modify this method, aiming to raise its quality to reach that of expensive ones. Some modifications were introduced to Shebl's technique. Two conventional mechanical pencil tips of different diameters were used to construct the recipient blocks. A source of mild heat was used, and blocks were incubated at 38°C overnight. With our modifications, 3 high-density TMA blocks were constructed. We successfully performed immunostaining without substantial tissue loss. Our modifications increased the number of cores per block and improved the stability of the cores within the paraffin block. This new, modified technique is a good alternative for expensive machines in many laboratories.

Comparison of manual lymph drainage therapy and connective tissue massage in women with fibromyalgia: a randomized controlled trial.

PubMed

Ekici, Gamze; Bakar, Yesim; Akbayrak, Turkan; Yuksel, Inci

2009-02-01

This study analyzed and compared the effects of manual lymph drainage therapy (MLDT) and connective tissue massage (CTM) in women with primary fibromyalgia (PFM). The study design was a randomized controlled trial. Fifty women with PFM completed the study. The patients were divided randomly into 2 groups. Whereas 25 of them received MLDT, the other 25 underwent CTM. The treatment program was carried out 5 times a week for 3 weeks in each group. Pain was evaluated by a visual analogue scale and algometry. The Fibromyalgia Impact Questionnaire (FIQ) and Nottingham Health Profile were used to describe health status and health-related quality of life (HRQoL). Wilcoxon signed rank test and Mann-Whitney U test were used to analyze the data. In both groups, significant improvements were found regarding pain intensity, pain pressure threshold, and HRQoL (P < .05). However, the scores of FIQ-7 (P = .006), FIQ-9 (P = .006), and FIQ-total (P = .010) were significantly lower in the MLDT group than they were in the CTM group at the end of treatment. For this particular group of patients, both MLDT and CTM appear to yield improvements in terms of pain, health status, and HRQoL. The results indicate that these manual therapy techniques might be used in the treatment of PFM. However, MLDT was found to be more effective than CTM according to some subitems of FIQ (morning tiredness and anxiety) and FIQ total score. Manual lymph drainage therapy might be preferred; however, further long-term follow-up studies are needed.

Skylab Saturn 1B flight manual

NASA Technical Reports Server (NTRS)

1972-01-01

A Saturn 1B Flight Manual provides launch vehicle systems descriptions and predicted performance data for the Skylab missions. Vehicle SL-2 (SA-206) is the baseline for this manual; but, as a result of the great similarity, the material is representative of SL-3 and SL-4 launch vehicles, also. The Flight Manual is not a control document but is intended primarily as an aid to astronauts who are training for Skylab missions. In order to provide a comprehensive reference for that purpose, the manual also contains descriptions of the ground support interfaces, prelaunch operations, and emergency procedures. Mission variables and constraints are summarized, and mission control monitoring and data flow during launch preparation and flight are discussed.

The 14th Annual Conference on Manual Control. [digital simulation of human operator dynamics

NASA Technical Reports Server (NTRS)

1978-01-01

Human operator dynamics during actual manual control or while monitoring the automatic control systems involved in air-to-air tracking, automobile driving, the operator of undersea vehicles, and remote handling are examined. Optimal control models and the use of mathematical theory in representing man behavior in complex man machine system tasks are discussed with emphasis on eye/head tracking and scanning; perception and attention allocation; decision making; and motion simulation and effects.

A study on special test stand of automatic and manual descent control in presence of simulated g-load effect

NASA Astrophysics Data System (ADS)

Glazkov, Yury; Artjuchin, Yury; Astakhov, Alexander; Vas'kov, Alexander; Malyshev, Veniamin; Mitroshin, Edward; Glinsky, Valery; Moiseenko, Vasily; Makovlev, Vyacheslav

The development of aircraft-type reusable space vehicles (RSV) involves the problem of complete compatibility of automatic, director and manual control. Task decision is complicated, in particular, due to considerable quantitative and qualitative changes of vehicle dynamic characteristics, little stability margins (and even of unstability) of the RSV, and stringent requirements to control accuracy at some flight phases. Besides, during control a pilot is affected by g-loads which hamper motor activity and deteriorate its accuracy, alter the functional status of the visual analyser, and influence higher nervous activity. A study of g-load effects on the control efficiency, especially in manual and director modes, is of primary importance. The main tools for study of a rational selection of manual and director vehicle control systems and as an aid in formulating recommendations for optimum crew-automatic control system interactions are special complex and functional flight simulator test stands. The proposed simulator stand includes a powerful digital computer complex combined with the control system of the centrifuge. The interior of a pilot's vehicle cabin is imitated. A situation image system, pyscho-physical monitoring system, physician, centrifuge operator, and instructor stations are linked with the test stand.

Tree Seed Technology Training Course - Instructor's Manual

Treesearch

F.T. Bonner; John A. Vozzo; W.W. Elam; S.B. Land

1994-01-01

This manual is intended primarily to train seed collectors, seed-plant managers, seed analysts, and nursery managers, but it can serve as a resource for any training course in forest regeneration. It includes both temperate and tropical tree species of all intended uses. The manual covers the following topics: seed biology, seed collection, seed handling, seed-quality...

Quality control of the RMS US flood model

NASA Astrophysics Data System (ADS)

Jankowfsky, Sonja; Hilberts, Arno; Mortgat, Chris; Li, Shuangcai; Rafique, Farhat; Rajesh, Edida; Xu, Na; Mei, Yi; Tillmanns, Stephan; Yang, Yang; Tian, Ye; Mathur, Prince; Kulkarni, Anand; Kumaresh, Bharadwaj Anna; Chaudhuri, Chiranjib; Saini, Vishal

2016-04-01

The RMS US flood model predicts the flood risk in the US with a 30 m resolution for different return periods. The model is designed for the insurance industry to estimate the cost of flood risk for a given location. Different statistical, hydrological and hydraulic models are combined to develop the flood maps for different return periods. A rainfall-runoff and routing model, calibrated with observed discharge data, is run with 10 000 years of stochastic simulated precipitation to create time series of discharge and surface runoff. The 100, 250 and 500 year events are extracted from these time series as forcing for a two-dimensional pluvial and fluvial inundation model. The coupling of all the different models which are run on the large area of the US implies a certain amount of uncertainty. Therefore, special attention is paid to the final quality control of the flood maps. First of all, a thorough quality analysis of the Digital Terrain model and the river network was done, as the final quality of the flood maps depends heavily on the DTM quality. Secondly, the simulated 100 year discharge in the major river network (600 000 km) is compared to the 100 year discharge derived using extreme value distribution of all USGS gauges with more than 20 years of peak values (around 11 000 gauges). Thirdly, for each gauge the modelled flood depth is compared to the depth derived from the USGS rating curves. Fourthly, the modelled flood depth is compared to the base flood elevation given in the FEMA flood maps. Fifthly, the flood extent is compared to the FEMA flood extent. Then, for historic events we compare flood extents and flood depths at given locations. Finally, all the data and spatial layers are uploaded on geoserver to facilitate the manual investigation of outliers. The feedback from the quality control is used to improve the model and estimate its uncertainty.

The effect of standing desks on manual control in children and young adults.

PubMed

Britten, L; Shire, K; Coats, R O; Astill, S L

2016-07-01

The aim of the present study was to establish if and how the additional postural constraint of standing affects accuracy and precision of goal directed naturalistic actions. Forty participants, comprising 20 young adults aged 20-23 years and 20 children aged 9-10 years completed 3 manual dexterity tasks on a tablet laptop with a handheld stylus during two separate conditions (1) while standing and (2) while seated. The order of conditions was counterbalanced across both groups of participants. The tasks were (1) a tracking task, where the stylus tracked a dot in a figure of 8 at 3 speeds, (2) an aiming task where the stylus moved from dot to dot with individual movements creating the outline of a pentagram and (3) a tracing task, where participants had to move the stylus along a static pathway or maze. Root mean squared error (RMSE), movement time and path accuracy, respectively, were used to quantify the effect that postural condition had on manual control. Overall adults were quicker and more accurate than children when performing all 3 tasks, and where the task speed was manipulated accuracy was better at slower speeds for all participants. Surprisingly, children performed these tasks more quickly and more accurately when standing compared to when sitting. In conclusion, standing at a desk while performing goal directed tasks did not detrimentally affect children's manual control, and moreover offered a benefit. Copyright © 2016 Elsevier B.V. All rights reserved.

General introduction for the “National Field Manual for the Collection of Water-Quality Data”

USGS Publications Warehouse

,

2018-02-28

BackgroundAs part of its mission, the U.S. Geological Survey (USGS) collects data to assess the quality of our Nation’s water resources. A high degree of reliability and standardization of these data are paramount to fulfilling this mission. Documentation of nationally accepted methods used by USGS personnel serves to maintain consistency and technical quality in data-collection activities. “The National Field Manual for the Collection of Water-Quality Data” (NFM) provides documented guidelines and protocols for USGS field personnel who collect water-quality data. The NFM provides detailed, comprehensive, and citable procedures for monitoring the quality of surface water and groundwater. Topics in the NFM include (1) methods and protocols for sampling water resources, (2) methods for processing samples for analysis of water quality, (3) methods for measuring field parameters, and (4) specialized procedures, such as sampling water for low levels of mercury and organic wastewater chemicals, measuring biological indicators, and sampling bottom sediment for chemistry. Personnel who collect water-quality data for national USGS programs and projects, including projects supported by USGS cooperative programs, are mandated to use protocols provided in the NFM per USGS Office of Water Quality Technical Memorandum 2002.13. Formal training, for example, as provided in the USGS class, “Field Water-Quality Methods for Groundwater and Surface Water,” and field apprenticeships supplement the guidance provided in the NFM and ensure that the data collected are high quality, accurate, and scientifically defensible.

PREVENTION REFERENCE MANUAL: OVERVIEWS ON PREVENTING AND CONTROLLING ACCIDENTIAL RELEASES OF SELECTED TOXIC CHEMICALS

EPA Science Inventory

The manual can be used to orient personnel involved in inspecting and otherwise evaluating potential toxic chemical release hazards to the fundamentals of release hazard control for 13 of the specific chemicals chosen for evaluation under Section 305(b) of the Superfund Amendment...

QUALITY CONTROLS FOR PCR

EPA Science Inventory

The purpose of this presentation is to present an overview of the quality control (QC) sections of a draft EPA document entitled, "Quality Assurance/Quality Control Guidance for Laboratories Performing PCR Analyses on Environmental Samples." This document has been prepared by th...

Biology Laboratory Safety Manual.

ERIC Educational Resources Information Center

Case, Christine L.

The Centers for Disease Control (CDC) recommends that schools prepare or adapt a biosafety manual, and that instructors develop a list of safety procedures applicable to their own lab and distribute it to each student. In this way, safety issues will be brought to each student's attention. This document is an example of such a manual. It contains…

Complex Networks Analysis of Manual and Machine Translations

NASA Astrophysics Data System (ADS)

Amancio, Diego R.; Antiqueira, Lucas; Pardo, Thiago A. S.; da F. Costa, Luciano; Oliveira, Osvaldo N.; Nunes, Maria G. V.

Complex networks have been increasingly used in text analysis, including in connection with natural language processing tools, as important text features appear to be captured by the topology and dynamics of the networks. Following previous works that apply complex networks concepts to text quality measurement, summary evaluation, and author characterization, we now focus on machine translation (MT). In this paper we assess the possible representation of texts as complex networks to evaluate cross-linguistic issues inherent in manual and machine translation. We show that different quality translations generated by MT tools can be distinguished from their manual counterparts by means of metrics such as in- (ID) and out-degrees (OD), clustering coefficient (CC), and shortest paths (SP). For instance, we demonstrate that the average OD in networks of automatic translations consistently exceeds the values obtained for manual ones, and that the CC values of source texts are not preserved for manual translations, but are for good automatic translations. This probably reflects the text rearrangements humans perform during manual translation. We envisage that such findings could lead to better MT tools and automatic evaluation metrics.

Pesticide Applicator Certification Training, Manual No. 1a: Agricultural Pest Control. a. Plant.

ERIC Educational Resources Information Center

Allen, W. A.; And Others

This manual provides information needed to meet the minimum standards for certification as an applicator of pesticides in the agricultural plant pest control category. Adapted for the State of Virginia, the text discusses: (1) the basics of insecticides; (2) insect pests; (3) selection and calibration of applicator equipment; and (4) the proper…

Template for updating regulations in QA manuals

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, M.G.; Banerjee, B.

1992-01-01

Recently, the U.S. Department of Energy (DOE) issued new quality assurance (QA) orders to reflect current policies for conduct and operation of DOE-authorized programs and facilities. Establishing traceability to new QA criteria and requirements from former multidraft orders, QA manuals, and guidance documentation for DOE-funded work can be confusing. Identified critical considerations still must be addressed. Most of the newly stated QA criteria can be cross referenced, where applicable, to former QA plans and manuals. Where additional criteria occur, new procedures may be required, together with revisions in QA plans and manuals.

Safe, Effective Use of Pesticides, A Manual for Commercial Applicators: Right-of-Way Pest Control.

ERIC Educational Resources Information Center

Extension Service (USDA), Washington, DC.

This manual is intended to assist pesticide applicators who are engaged in right-of-way pest control to meet the requirements of the Michigan Department of Agriculture for certification. While the majority of material in this guide pertains to vegetation management, the guide also addresses right-of-way insect and fungus control. An introduction…

Visuo‐manual tracking: does intermittent control with aperiodic sampling explain linear power and non‐linear remnant without sensorimotor noise?

PubMed Central

Gawthrop, Peter J.; Lakie, Martin; Loram, Ian D.

2017-01-01

Key points A human controlling an external system is described most easily and conventionally as linearly and continuously translating sensory input to motor output, with the inevitable output remnant, non‐linearly related to the input, attributed to sensorimotor noise.Recent experiments show sustained manual tracking involves repeated refractoriness (insensitivity to sensory information for a certain duration), with the temporary 200–500 ms periods of irresponsiveness to sensory input making the control process intrinsically non‐linear.This evidence calls for re‐examination of the extent to which random sensorimotor noise is required to explain the non‐linear remnant.This investigation of manual tracking shows how the full motor output (linear component and remnant) can be explained mechanistically by aperiodic sampling triggered by prediction error thresholds.Whereas broadband physiological noise is general to all processes, aperiodic sampling is associated with sensorimotor decision making within specific frontal, striatal and parietal networks; we conclude that manual tracking utilises such slow serial decision making pathways up to several times per second. Abstract The human operator is described adequately by linear translation of sensory input to motor output. Motor output also always includes a non‐linear remnant resulting from random sensorimotor noise from multiple sources, and non‐linear input transformations, for example thresholds or refractory periods. Recent evidence showed that manual tracking incurs substantial, serial, refractoriness (insensitivity to sensory information of 350 and 550 ms for 1st and 2nd order systems respectively). Our two questions are: (i) What are the comparative merits of explaining the non‐linear remnant using noise or non‐linear transformations? (ii) Can non‐linear transformations represent serial motor decision making within the sensorimotor feedback loop intrinsic to tracking? Twelve participants

Visuo-manual tracking: does intermittent control with aperiodic sampling explain linear power and non-linear remnant without sensorimotor noise?

PubMed

Gollee, Henrik; Gawthrop, Peter J; Lakie, Martin; Loram, Ian D

2017-11-01

A human controlling an external system is described most easily and conventionally as linearly and continuously translating sensory input to motor output, with the inevitable output remnant, non-linearly related to the input, attributed to sensorimotor noise. Recent experiments show sustained manual tracking involves repeated refractoriness (insensitivity to sensory information for a certain duration), with the temporary 200-500 ms periods of irresponsiveness to sensory input making the control process intrinsically non-linear. This evidence calls for re-examination of the extent to which random sensorimotor noise is required to explain the non-linear remnant. This investigation of manual tracking shows how the full motor output (linear component and remnant) can be explained mechanistically by aperiodic sampling triggered by prediction error thresholds. Whereas broadband physiological noise is general to all processes, aperiodic sampling is associated with sensorimotor decision making within specific frontal, striatal and parietal networks; we conclude that manual tracking utilises such slow serial decision making pathways up to several times per second. The human operator is described adequately by linear translation of sensory input to motor output. Motor output also always includes a non-linear remnant resulting from random sensorimotor noise from multiple sources, and non-linear input transformations, for example thresholds or refractory periods. Recent evidence showed that manual tracking incurs substantial, serial, refractoriness (insensitivity to sensory information of 350 and 550 ms for 1st and 2nd order systems respectively). Our two questions are: (i) What are the comparative merits of explaining the non-linear remnant using noise or non-linear transformations? (ii) Can non-linear transformations represent serial motor decision making within the sensorimotor feedback loop intrinsic to tracking? Twelve participants (instructed to act in three prescribed

The influence of ship motion of manual control skills

NASA Technical Reports Server (NTRS)

Mcleod, P.; Poulton, C.; Duross, H.; Lewis, W.

1981-01-01

The effects of ship motion on a range of typical manual control skills were examined on the Warren Spring ship motion simulator driven in heave, pitch, and roll by signals taken from the frigate HMS Avenger at 13 m/s (25 knots) into a force 4 wind. The motion produced a vertical r.m.s. acceleration of 0.024g, mostly between 0.1 and 0.3 Hz, with comparatively little pitch or roll. A task involving unsupported arm movements was seriously affected by the motion; a pursuit tracking task showed a reliable decrement although it was still performed reasonably well (pressure and free moving tracking controls were affected equally by the motion); a digit keying task requiring ballistic hand movements was unaffected. There was no evidence that these effects were caused by sea sickness. The differing response to motion of the different tasks, from virtual destruction to no effect, suggests that a major benefit could come from an attempt to design the man/control interface onboard ship around motion resistant tasks.

Exercise, Manual Therapy, and Booster Sessions in Knee Osteoarthritis: Cost-Effectiveness Analysis From a Multicenter Randomized Controlled Trial.

PubMed

Bove, Allyn M; Smith, Kenneth J; Bise, Christopher G; Fritz, Julie M; Childs, John; Brennan, Gerard P; Abbott, J Haxby; Fitzgerald, G Kelley

2018-01-01

Limited information exists regarding the cost-effectiveness of rehabilitation strategies for individuals with knee osteoarthritis (OA). The study objective was to compare the cost-effectiveness of 4 different combinations of exercise, manual therapy, and booster sessions for individuals with knee OA. This economic evaluation involved a cost-effectiveness analysis performed alongside a multicenter randomized controlled trial. The study took place in Pittsburgh, Pennsylvania; Salt Lake City, Utah; and San Antonio, Texas. The study participants were 300 individuals taking part in a randomized controlled trial investigating various physical therapy strategies for knee OA. Participants were randomized into 4 treatment groups: exercise only (EX), exercise plus booster sessions (EX+B), exercise plus manual therapy (EX+MT), and exercise plus manual therapy and booster sessions (EX+MT+B). For the 2-year base case scenario, a Markov model was constructed using the United States societal perspective and a 3% discount rate for costs and quality-adjusted life years (QALYs). Incremental cost-effectiveness ratios were calculated to compare differences in cost per QALY gained among the 4 treatment strategies. In the 2-year analysis, booster strategies (EX+MT+B and EX+B) dominated no-booster strategies, with both lower health care costs and greater effectiveness. EX+MT+B had the lowest total health care costs. EX+B cost ${\\$}$1061 more and gained 0.082 more QALYs than EX+MT+B, for an incremental cost-effectiveness ratio of ${\\$}$12,900/QALY gained. The small number of total knee arthroplasty surgeries received by individuals in this study made the assessment of whether any particular strategy was more successful at delaying or preventing surgery in individuals with knee OA difficult. Spacing exercise-based physical therapy sessions over 12 months using periodic booster sessions was less costly and more effective over 2 years than strategies not containing booster sessions for

Drywall Finishing Manual.

ERIC Educational Resources Information Center

Lengert, Gerald

This manual, a self-study guide for apprentices in the drywall finishing trade in British Columbia, attempts to establish standards for the trade. It tells how to produce a properly taped and filled drywall surface and describes what that surface should look like. The standards emphasize quality work that can be realistically achieved on the job.…

[On-site quality control of acupuncture randomized controlled trial: design of content and checklist of quality control based on PICOST].

PubMed

Li, Hong-Jiao; He, Li-Yun; Liu, Zhi-Shun; Sun, Ya-Nan; Yan, Shi-Yan; Liu, Jia; Zhao, Ye; Liu, Bao-Yan

2014-02-01

To effectively guarantee quality of randomized controlld trial (RCT) of acupuncture and develop reasonable content and checklist of on-site quality control, influencing factors on quality of acupuncture RCT are analyzed and scientificity of quality control content and feasibility of on-site manipulation are put into overall consideration. Based on content and checklist of on-site quality control in National 11th Five-Year Plan Project Optimization of Comprehensive Treatment Plan for TCM in Prevention and Treatment of Serious Disease and Clinical Assessment on Generic Technology and Quality Control Research, it is proposed that on-site quality control of acupuncture RCT should be conducted with PICOST (patient, intervention, comparison, out come, site and time) as core, especially on quality control of interveners' skills and outcome assessment of blinding, and checklist of on-site quality control is developed to provide references for undertaking groups of the project.

Comparative evaluation of toric intraocular lens alignment and visual quality with image-guided surgery and conventional three-step manual marking.

PubMed

Titiyal, Jeewan S; Kaur, Manpreet; Jose, Cijin P; Falera, Ruchita; Kinkar, Ashutosh; Bageshwar, Lalit Ms

2018-01-01

To compare toric intraocular lens (IOL) alignment assisted by image-guided surgery or manual marking methods and its impact on visual quality. This prospective comparative study enrolled 80 eyes with cataract and astigmatism ≥1.5 D to undergo phacoemulsification with toric IOL alignment by manual marking method using bubble marker (group I, n=40) or Callisto eye and Z align (group II, n=40). Postoperatively, accuracy of alignment and visual quality was assessed with a ray tracing aberrometer. Primary outcome measure was deviation from the target axis of implantation. Secondary outcome measures were visual quality and acuity. Follow-up was performed on postoperative days (PODs) 1 and 30. Deviation from the target axis of implantation was significantly less in group II on PODs 1 and 30 (group I: 5.5°±3.3°, group II: 3.6°±2.6°; p =0.005). Postoperative refractive cylinder was -0.89±0.35 D in group I and -0.64±0.36 D in group II ( p =0.003). Visual acuity was comparable between both the groups. Visual quality measured in terms of Strehl ratio ( p <0.05) and modulation transfer function (MTF) ( p <0.05) was significantly better in the image-guided surgery group. Significant negative correlation was observed between deviation from target axis and visual quality parameters (Strehl ratio and MTF) ( p <0.05). Image-guided surgery allows precise alignment of toric IOL without need for reference marking. It is associated with superior visual quality which correlates with the precision of IOL alignment.

National Field Manual for the Collection of Water-Quality Data. U.S. Geological Survey Techniques of Water-Resources Investigations, Book 9

USGS Publications Warehouse

2015-01-01

The mission of the Water Resources Discipline of the U.S. Geological Survey (USGS) is to provide the information and understanding needed for wise management of the Nation's water resources. Inherent in this mission is the responsibility to collect data that accurately describe the physical, chemical, and biological attributes of water systems. These data are used for environmental and resource assessments by the USGS, other government agenices and scientific organizations, and the general public. Reliable and quality-assured data are essential to the credibility and impartiality of the water-resources appraisals carried out by the USGS. The development and use of a National Field Manual is necessary to achieve consistency in the scientific methods and procedures used, to document those methods and procedures, and to maintain technical expertise. USGS field personnel use this manual to ensure that the data collected are of the quality required to fulfill our mission.

Christmas Tree Pest Manual

Treesearch

Department of Entomology Michigan State University

1998-01-01

This manual can help you identify and control damaging Christmas tree pests in the North Central region of the United States. Most of the information also applies to the northeastern states and to the southern portions of the Canadian Provinces that border these states. You do not have to be a pest specialist to use this information; we wrote the manual in everyday...

METRO-APEX Volume 10.1: Developer's Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The Developer's Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution Exercise…

METRO-APEX Volume 5.1: Planner's Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The Planner's Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution Exercise…

Ornamental and Turf Pest Control for Commercial Applicators: Pest Control of Ornamental Plants; NCR 12, Lawn Diseases in the Midwest; NCR 26, Lawn Weeds and their Control. Manual 89.

ERIC Educational Resources Information Center

Craig, W. S., Comp.; And Others

This training manual provides information needed to meet the minimum EPA standards for certification as a commercial applicator of pesticides in the ornamental and turf pest control category. The text discusses pest control of ornamental plants, lawn diseases, and lawn weeds and their control. (CS)

Simulator evaluation of display concepts for pilot monitoring and control of space shuttle approach and landing. Phase 2: Manual flight control

NASA Technical Reports Server (NTRS)

Gartner, W. B.; Baldwin, K. M.

1973-01-01

A study of the display requirements for final approach management of the space shuttle orbiter vehicle is presented. An experimental display concept, providing a more direct, pictorial representation of the vehicle's movement relative to the selected approach path and aiming points, was developed and assessed as an aid to manual flight path control. Both head-up, windshield projections and head-down, panel mounted presentations of the experimental display were evaluated in a series of simulated orbiter approach sequence. Data obtained indicate that the experimental display would enable orbiter pilots to exercise greater flexibility in implementing alternative final approach control strategies. Touchdown position and airspeed dispersion criteria were satisfied on 91 percent of the approach sequences, representing various profile and wind effect conditions. Flight path control and airspeed management satisfied operationally-relevant criteria for the two-segment, power-off orbiter approach and were consistently more accurate and less variable when the full set of experimental display elements was available to the pilot. Approach control tended to be more precise when the head-up display was used; however, the data also indicate that the head-down display would provide adequate support for the manual control task.

Development of feedforward control in a dynamic manual tracking task.

PubMed

van Roon, Dominique; Caeyenberghs, Karen; Swinnen, Stephan P; Smits-Engelsman, Bouwien C M

2008-01-01

To examine the development of feedforward control during manual tracking, 117 participants in 5 age groups (6 to 7, 8 to 9, 10 to 11, 12 to 14, and 15 to 17 years) tracked an accelerating dot presented on a monitor by moving an electronic pen on a digitizer. To remain successful at higher target velocities, they had to create a predictive model of the target's motion. The ability to track the target at higher velocities increased, and the application of a feedback-based step-and-hold strategy decreased with age, as shown by increases in maximum target velocity and decreases in number of stops between ages 6-7 and 8-9 and between ages 8-9 and 10-11. The ability to exploit feedforward control in a dynamic tracking task improves significantly with age.

Optimizing the balance between task automation and human manual control in simulated submarine track management.

PubMed

Chen, Stephanie I; Visser, Troy A W; Huf, Samuel; Loft, Shayne

2017-09-01

Automation can improve operator performance and reduce workload, but can also degrade operator situation awareness (SA) and the ability to regain manual control. In 3 experiments, we examined the extent to which automation could be designed to benefit performance while ensuring that individuals maintained SA and could regain manual control. Participants completed a simulated submarine track management task under varying task load. The automation was designed to facilitate information acquisition and analysis, but did not make task decisions. Relative to a condition with no automation, the continuous use of automation improved performance and reduced subjective workload, but degraded SA. Automation that was engaged and disengaged by participants as required (adaptable automation) moderately improved performance and reduced workload relative to no automation, but degraded SA. Automation engaged and disengaged based on task load (adaptive automation) provided no benefit to performance or workload, and degraded SA relative to no automation. Automation never led to significant return-to-manual deficits. However, all types of automation led to degraded performance on a nonautomated task that shared information processing requirements with automated tasks. Given these outcomes, further research is urgently required to establish how to design automation to maximize performance while keeping operators cognitively engaged. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

[Quality control in anesthesiology].

PubMed

Muñoz-Ramón, J M

1995-03-01

The process of quality control and auditing of anesthesiology allows us to evaluate care given by a service and solve problems that are detected. Quality control is a basic element of care giving and is only secondarily an area of academic research; it is therefore a meaningless effort if the information does not serve to improve departmental procedures. Quality assurance procedures assume certain infrastructural requirements and an initial period of implementation and adjustment. The main objectives of quality control are the reduction of morbidity and mortality due to anesthesia, assurance of the availability and proper management of resources and, finally, the well-being and safety of the patient.

WIPP waste characterization program sampling and analysis guidance manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-01-01

The Waste Isolation Pilot Plant (WIPP) Waste Characterization Program Sampling and Analysis Guidance Manual (Guidance Manual) provides a unified source of information on the sampling and analytical techniques that enable Department of Energy (DOE) facilities to comply with the requirements established in the current revision of the Quality Assurance Program Plan (QAPP) for the WIPP Experimental-Waste Characterization Program (the Program). This Guidance Manual includes all of the sampling and testing methodologies accepted by the WIPP Project Office (DOE/WPO) for use in implementing the Program requirements specified in the QAPP. This includes methods for characterizing representative samples of transuranic (TRU) wastesmore » at DOE generator sites with respect to the gas generation controlling variables defined in the WIPP bin-scale and alcove test plans, as well as waste container headspace gas sampling and analytical procedures to support waste characterization requirements under the WIPP test program and the Resource Conservation and Recovery Act (RCRA). The procedures in this Guidance Manual are comprehensive and detailed and are designed to provide the necessary guidance for the preparation of site specific procedures. The use of these procedures is intended to provide the necessary sensitivity, specificity, precision, and comparability of analyses and test results. The solutions to achieving specific program objectives will depend upon facility constraints, compliance with DOE Orders and DOE facilities' operating contractor requirements, and the knowledge and experience of the TRU waste handlers and analysts. With some analytical methods, such as gas chromatography/mass spectrometry, the Guidance Manual procedures may be used directly. With other methods, such as nondestructive/destructive characterization, the Guidance Manual provides guidance rather than a step-by-step procedure.« less

Launch Vehicle Manual Steering with Adaptive Augmenting Control:In-Flight Evaluations of Adverse Interactions Using a Piloted Aircraft

NASA Technical Reports Server (NTRS)

Hanson, Curt; Miller, Chris; Wall, John H.; VanZwieten, Tannen S.; Gilligan, Eric T.; Orr, Jeb S.

2015-01-01

An Adaptive Augmenting Control (AAC) algorithm for the Space Launch System (SLS) has been developed at the Marshall Space Flight Center (MSFC) as part of the launch vehicle's baseline flight control system. A prototype version of the SLS flight control software was hosted on a piloted aircraft at the Armstrong Flight Research Center to demonstrate the adaptive controller on a full-scale realistic application in a relevant flight environment. Concerns regarding adverse interactions between the adaptive controller and a potential manual steering mode were also investigated by giving the pilot trajectory deviation cues and pitch rate command authority, which is the subject of this paper. Two NASA research pilots flew a total of 25 constant pitch rate trajectories using a prototype manual steering mode with and without adaptive control, evaluating six different nominal and off-nominal test case scenarios. Pilot comments and PIO ratings were given following each trajectory and correlated with aircraft state data and internal controller signals post-flight.

Active versus passive adverse event reporting after pediatric chiropractic manual therapy: study protocol for a cluster randomized controlled trial.

PubMed

Pohlman, Katherine A; Carroll, Linda; Tsuyuki, Ross T; Hartling, Lisa; Vohra, Sunita

2017-12-01

Patient safety performance can be assessed with several systems, including passive and active surveillance. Passive surveillance systems provide opportunity for health care personnel to confidentially and voluntarily report incidents, including adverse events, occurring in their work environment. Active surveillance systems systematically monitor patient encounters to seek detailed information about adverse events that occur in work environments; unlike passive surveillance, active surveillance allows for collection of both numerator (number of adverse events) and denominator (number of patients seen) data. Chiropractic manual therapy is commonly used in both adults and children, yet few studies have been done to evaluate the safety of chiropractic manual therapy for children. In an attempt to evaluate this, this study will compare adverse event reporting in passive versus active surveillance systems after chiropractic manual therapy in the pediatric population. This cluster randomized controlled trial aims to enroll 70 physicians of chiropractic (unit of randomization) to either passive or active surveillance system to report adverse events that occur after treatment for 60 consecutive pediatric (13 years of age and younger) patient visits (unit of analysis). A modified enrollment process with a two-phase consent procedure will be implemented to maintain provider blinding and minimize dropouts. The first phase of consent is for the provider to confirm their interest in a trial investigating the safety of chiropractic manual therapy. The second phase ensures that they understand the specific requirements for the group to which they were randomized. Percentages, incidence estimates, and 95% confidence intervals will be used to describe the count of reported adverse events in each group. The primary outcome will be the number and quality of the adverse event reports in the active versus the passive surveillance group. With 80% power and 5% one-sided significance

Enhancement of the Automated Quality Control Procedures for the International Soil Moisture Network

NASA Astrophysics Data System (ADS)

Heer, Elsa; Xaver, Angelika; Dorigo, Wouter; Messner, Romina

2017-04-01

spectrum where a high majority of values before and after is flagged and therefore a sensor malfunction is certain. For the evaluation of the enhanced automated quality control system many test data sets were chosen, and manually validated to be compared to the existing quality control procedures and the new algorithms. Improvements will be shown that assure an appropriate assessment of the ISMN data sets, which are used for validations of soil moisture data retrieved by satellite data and are the foundation many other scientific publications.

Biosafety Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, Bruce W.

2010-05-18

Work with or potential exposure to biological materials in the course of performing research or other work activities at Lawrence Berkeley National Laboratory (LBNL) must be conducted in a safe, ethical, environmentally sound, and compliant manner. Work must be conducted in accordance with established biosafety standards, the principles and functions of Integrated Safety Management (ISM), this Biosafety Manual, Chapter 26 (Biosafety) of the Health and Safety Manual (PUB-3000), and applicable standards and LBNL policies. The purpose of the Biosafety Program is to protect workers, the public, agriculture, and the environment from exposure to biological agents or materials that may causemore » disease or other detrimental effects in humans, animals, or plants. This manual provides workers; line management; Environment, Health, and Safety (EH&S) Division staff; Institutional Biosafety Committee (IBC) members; and others with a comprehensive overview of biosafety principles, requirements from biosafety standards, and measures needed to control biological risks in work activities and facilities at LBNL.« less

Evaluation of the effectiveness of manual chest physiotherapy techniques on quality of life at six months post exacerbation of COPD (MATREX): a randomised controlled equivalence trial

PubMed Central

2012-01-01

Background Manual chest physiotherapy (MCP) techniques involving chest percussion, vibration, and shaking have long been used in the treatment of respiratory conditions. However, methodological limitations in existing research have led to a state of clinical equipoise with respect to this treatment. Thus, for patients hospitalised with an exacerbation of Chronic Obstructive Pulmonary Disease (COPD), clinical preference tends to dictate whether MCP is given to assist with sputum clearance. We standardised the delivery of MCP and assessed its effectiveness on disease-specific quality of life. Methods In this randomised, controlled trial powered for equivalence, 526 patients hospitalised with acute COPD exacerbation were enrolled from four centres in the UK. Patients were allocated to receive MCP plus advice on airway clearance or advice on chest clearance alone. The primary outcome was a COPD specific quality of life measure, the Saint Georges Respiratory Questionnaire (SGRQ) at six months post randomisation. Analyses were by intention to treat (ITT). This study was registered, ISRCTN13825248. Results All patients were included in the analyses, of which 372 (71%) provided evaluable data for the primary outcome. An effect size of 0·3 standard deviations in SGRQ score was specified as the threshold for superiority. The ITT analyses showed no significant difference in SGRQ for patients who did, or did not receive MCP (95% CI −0·14 to 0·19). Conclusions These data do not lend support to the routine use of MCP in the management of acute exacerbation of COPD. However, this does not mean that MCP is of no therapeutic value to COPD patients in specific circumstances. PMID:22748085

Mechanical vs. manual cleaning of hospital beds: a prospective intervention study.

PubMed

Hopman, J; Nillesen, M; de Both, E; Witte, J; Teerenstra, S; Hulscher, M; Voss, A

2015-06-01

Cleaning regimens for hospital beds were evaluated in the context of a rising prevalence of highly resistant micro-organisms and increasing financial pressure on healthcare systems. Dutch hospitals have to choose between standardized, mechanical bed-washers advised in national guidance and manual cleaning. To evaluate the quality of mechanical and manual bed-cleaning regimens. The multi-faceted analysis of bed-cleaning regimens consisted of three steps. In Step 1, the training of the domestic service team was evaluated. In Step 2, the cleaning quality of manual and mechanical regimens was assessed. Soiled beds, obtained at random, from different departments were evaluated using microbiological analysis (N = 40) and ATP (N = 20). ATP and microbiological contamination were measured in five predetermined locations on all beds. In Step 3, manual cleaning was introduced over a two-month pilot study at the surgical short-stay unit, and beds from other departments were processed according to the 'gold standard' mechanical cleaning. ATP levels were evaluated in three locations on 300 beds after cleaning. Training was found to improve the quality of cleaning significantly. Mechanical cleaning resulted in significantly lower ATP levels than manual cleaning. Mechanical cleaning shows less variation and results in consistently lower ATP levels than manual cleaning. Copyright © 2015 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Comparative evaluation of toric intraocular lens alignment and visual quality with image-guided surgery and conventional three-step manual marking

PubMed Central

Titiyal, Jeewan S; Kaur, Manpreet; Jose, Cijin P; Falera, Ruchita; Kinkar, Ashutosh; Bageshwar, Lalit MS

2018-01-01

Purpose To compare toric intraocular lens (IOL) alignment assisted by image-guided surgery or manual marking methods and its impact on visual quality. Patients and methods This prospective comparative study enrolled 80 eyes with cataract and astigmatism ≥1.5 D to undergo phacoemulsification with toric IOL alignment by manual marking method using bubble marker (group I, n=40) or Callisto eye and Z align (group II, n=40). Postoperatively, accuracy of alignment and visual quality was assessed with a ray tracing aberrometer. Primary outcome measure was deviation from the target axis of implantation. Secondary outcome measures were visual quality and acuity. Follow-up was performed on postoperative days (PODs) 1 and 30. Results Deviation from the target axis of implantation was significantly less in group II on PODs 1 and 30 (group I: 5.5°±3.3°, group II: 3.6°±2.6°; p=0.005). Postoperative refractive cylinder was −0.89±0.35 D in group I and −0.64±0.36 D in group II (p=0.003). Visual acuity was comparable between both the groups. Visual quality measured in terms of Strehl ratio (p<0.05) and modulation transfer function (MTF) (p<0.05) was significantly better in the image-guided surgery group. Significant negative correlation was observed between deviation from target axis and visual quality parameters (Strehl ratio and MTF) (p<0.05). Conclusion Image-guided surgery allows precise alignment of toric IOL without need for reference marking. It is associated with superior visual quality which correlates with the precision of IOL alignment. PMID:29731603

Equipment Management Manual

NASA Technical Reports Server (NTRS)

1992-01-01

The NASA Equipment Management Manual (NHB 4200.1) is issued pursuant to Section 203(c)(1) of the National Aeronautics and Space Act of 1958, as amended (42 USC 2473), and sets forth policy, uniform performance standards, and procedural guidance to NASA personnel for the acquisition, management, and use of NASA-owned equipment. This revision is effective upon receipt. This is a controlled manual, issued in loose-leaf form, and revised through page changes. Additional copies for internal use may be obtained through normal distribution.

Launch Vehicle Manual Steering with Adaptive Augmenting Control In-flight Evaluations Using a Piloted Aircraft

NASA Technical Reports Server (NTRS)

Hanson, Curt

2014-01-01

An adaptive augmenting control algorithm for the Space Launch System has been developed at the Marshall Space Flight Center as part of the launch vehicles baseline flight control system. A prototype version of the SLS flight control software was hosted on a piloted aircraft at the Armstrong Flight Research Center to demonstrate the adaptive controller on a full-scale realistic application in a relevant flight environment. Concerns regarding adverse interactions between the adaptive controller and a proposed manual steering mode were investigated by giving the pilot trajectory deviation cues and pitch rate command authority.

A new hyperspectral imaging based device for quality control in plastic recycling

NASA Astrophysics Data System (ADS)

Bonifazi, G.; D'Agostini, M.; Dall'Ava, A.; Serranti, S.; Turioni, F.

2013-05-01

The quality control of contamination level in the recycled plastics stream has been identified as an important key factor for increasing the value of the recycled material by both plastic recycling and compounder industries. Existing quality control methods for the detection of both plastics and non-plastics contaminants in the plastic waste streams at different stages of the industrial process (e.g. feed, intermediate and final products) are currently based on the manual collection from the stream of a sample and on the subsequent off-line laboratory analyses. The results of such analyses are usually available after some hours, or sometimes even some days, after the material has been processed. The laboratory analyses are time-consuming and expensive (both in terms of equipment cost and their maintenance and of labour cost).Therefore, a fast on-line assessment to monitor the plastic waste feed streams and to characterize the composition of the different plastic products, is fundamental to increase the value of secondary plastics. The paper is finalized to describe and evaluate the development of an HSI-based device and of the related software architectures and processing algorithms for quality assessment of plastics in recycling plants, with particular reference to polyolefins (PO). NIR-HSI sensing devices coupled with multivariate data analysis methods was demonstrated as an objective, rapid and non-destructive technique that can be used for on-line quality and process control in the recycling process of POs. In particular, the adoption of the previous mentioned HD&SW integrated architectures can provide a solution to one of the major problems of the recycling industry, which is the lack of an accurate quality certification of materials obtained by recycling processes. These results could therefore assist in developing strategies to certify the composition of recycled PO products.

Commercial jet fuel quality control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strauss, K.H.

1995-05-01

The paper discusses the purpose of jet fuel quality control between the refinery and the aircraft. It describes fixed equipment, including various types of filters, and the usefulness and limitations of this equipment. Test equipment is reviewed as are various surveillance procedures. These include the Air Transport Association specification ATA 103, the FAA Advisory Circular 150/5230-4, the International Air Transport Association Guidance Material for Fuel Quality Control and Fuelling Service and the Guidelines for Quality Control at Jointly Operated Fuel Systems. Some past and current quality control problems are briefly mentioned.

Iowa Commercial Pesticide Applicator Manual, Category 6: Right-of-Way Pest Control. CS-18.

ERIC Educational Resources Information Center

Jennings, Vivan M.; Ryan, Stephan O.

This manual provides information needed to meet specific standards for certification as a pesticide applicator. The text discusses important right-of-way weeds and unwanted woody plants and provides suggestions for both long- and short-term control. Attention is also given to special problems associated with application of right-of-way herbicides.…

VDOT manual of practice for planning stormwater management.

DOT National Transportation Integrated Search

1992-01-01

The final report is in the form of a manual of practice for the VDOT to use in planning its stormwater management strategies. The manual was proposed to aid in the selection and design of erosion control practices and stormwater control practices for...

A manual control theory analysis of vertical situation displays for STOL aircraft

NASA Technical Reports Server (NTRS)

Baron, S.; Levison, W. H.

1973-01-01

Pilot-vehicle-display systems theory is applied to the analysis of proposed vertical situation displays for manual control in approach-to-landing of a STOL aircraft. The effects of display variables on pilot workload and on total closed-loop system performance was calculated using an optimal-control model for the human operator. The steep approach of an augmentor wing jet STOL aircraft was analyzed. Both random turbulence and mean-wind shears were considered. Linearized perturbation equations were used to describe longitudinal and lateral dynamics of the aircraft. The basic display configuration was one that abstracted the essential status information (including glide-slope and localizer errors) of an EADI display. Proposed flight director displays for both longitudinal and lateral control were also investigated.

Applicator Training Manual for: Forest Pest Control.

ERIC Educational Resources Information Center

Newman, Jim

Described in this manual is the use of insecticides, fungicides, and herbicides in forestry. Both diseases and insects found in hardwoods and conifers are covered. Detailed information is given on methods of herbicide application. Finally, five important environmental considerations are given. (BB)

21 CFR 892.5650 - Manual radionuclide applicator system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... system. (a) Identification. A manual radionuclide applicator system is a manually operated device... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Manual radionuclide applicator system. 892.5650... planning computer programs, and accessories. (b) Classification. Class I (general controls). The device is...

21 CFR 892.5650 - Manual radionuclide applicator system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... system. (a) Identification. A manual radionuclide applicator system is a manually operated device... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Manual radionuclide applicator system. 892.5650... planning computer programs, and accessories. (b) Classification. Class I (general controls). The device is...

21 CFR 892.5650 - Manual radionuclide applicator system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... system. (a) Identification. A manual radionuclide applicator system is a manually operated device... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Manual radionuclide applicator system. 892.5650... planning computer programs, and accessories. (b) Classification. Class I (general controls). The device is...

21 CFR 892.5650 - Manual radionuclide applicator system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... system. (a) Identification. A manual radionuclide applicator system is a manually operated device... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Manual radionuclide applicator system. 892.5650... planning computer programs, and accessories. (b) Classification. Class I (general controls). The device is...

21 CFR 892.5650 - Manual radionuclide applicator system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... system. (a) Identification. A manual radionuclide applicator system is a manually operated device... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Manual radionuclide applicator system. 892.5650... planning computer programs, and accessories. (b) Classification. Class I (general controls). The device is...

Fiscal Accounting Manual.

ERIC Educational Resources Information Center

California State Dept. of Housing and Community Development, Sacramento. Indian Assistance Program.

Written in simple, easy to understand form, the manual provides a vehicle for the untrained person in bookkeeping to control funds received from grants for Indian Tribal Councils and Indian organizations. The method used to control grants (federal, state, or private) is fund accounting, designed to organize rendering services on a non-profit…

METRO-APEX Volume 21.1: Pressure Groups' Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The Pressure Groups' Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution…

METRO-APEX Volume 20.1: News Media Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The News Media Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution Exercise…

METRO-APEX Volume 18.1: Legal Reference Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The Legal Reference Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution…

METRO-APEX Volume 4.1: County Politician's Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The County Politician's Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution…

METRO-APEX Volume 3.1: City Politician's Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The City Politician's Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution…

METRO-APEX Volume 2.1: Computer Operator's Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The Computer Operator's Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution…

MICROBIAL LABORATORY GUIDANCE MANUAL FOR THE ...

EPA Pesticide Factsheets

The Long-Term 2 Enhanced Surface Water Treatment Rule Laboratory Instruction Manual will be a compilation of all information needed by laboratories and field personnel to collect, analyze, and report the microbiological data required under the rule. The manual will provide laboratories with a single source of information that currently is available from various sources including the latest versions of Methods 1622 and 1623, including all approved, equivalent modifications; the procedures for E.coli methods approved for use under the LT2ESWTR; lists of vendor sources; data recording forms; data reporting requirements; information on the Laboratory Quality Assurance Evaluation Program for the Analysis of Cryptosporidium in Water; and sample collection procedures. Although most of this information is available elsewhere, a single, comprehensive compendium containing this information is needed to aid utilities and laboratories performing the sampling and analysis activities required under the LT2 rule. This manual will serve as an instruction manual for laboratories to use when collecting data for Crypto, E. coli and turbidity.

Head Start Facilities Manual.

ERIC Educational Resources Information Center

Research Assessment Management, Inc., Silver Spring, MD.

A quality Head Start facility should provide a physical environment responsive both to the needs of the children and families served and to the needs of staff, volunteers, and community agencies that share space with Head Start. This manual is a tool for Head Start grantees and delegate agencies for assessing existing facilities, making…

Adverse events after manual therapy among patients seeking care for neck and/or back pain: a randomized controlled trial.

PubMed

Paanalahti, Kari; Holm, Lena W; Nordin, Margareta; Asker, Martin; Lyander, Jessica; Skillgate, Eva

2014-03-12

The safety of the manual treatment techniques such as spinal manipulation has been discussed and there is a need for more information about potential adverse events after manual therapy. The aim of this randomized controlled trial was to investigate differences in occurrence of adverse events between three different combinations of manual treatment techniques used by manual therapists (i.e. chiropractors, naprapaths, osteopaths, physicians and physiotherapists) for patients seeking care for back and/or neck pain. In addition women and men were compared regarding the occurrence of adverse events. Participants were recruited among patients, ages 18-65, seeking care at the educational clinic of the Scandinavian College of Naprapathic Manual Medicine in Stockholm. The patients (n = 767) were randomized to one of three treatment arms 1) manual therapy (i.e. spinal manipulation, spinal mobilization, stretching and massage) (n = 249), 2) manual therapy excluding spinal manipulation (n = 258) and 3) manual therapy excluding stretching (n = 260). Treatments were provided by students in the seventh semester of total eight. Adverse events were measured with a questionnaire after each return visit and categorized in to five levels; 1) short minor, 2) long minor, 3) short moderate, 4) long moderate and 5) serious adverse events, based on the duration and/or severity of the event. Generalized estimating equations were used to examine the association between adverse event and treatments arms. The most common adverse events were soreness in muscles, increased pain and stiffness. No differences were found between the treatment arms concerning the occurrence of adverse event. Fifty-one percent of patients, who received at least three treatments, experienced at least one adverse event after one or more visits. Women more often had short moderate adverse events (OR = 2.19 (95% CI: 1.52-3.15)), and long moderate adverse events (OR = 2.49 (95% CI: 1.77-3.52)) compared to men. Adverse

The disconnect between evidence and practice: a systematic review of person-centred interventions and training manuals for care home staff working with people with dementia.

PubMed

Fossey, Jane; Masson, Sarah; Stafford, Jane; Lawrence, Vanessa; Corbett, Anne; Ballard, Clive

2014-08-01

The overall objective is to determine the availability of person-centred intervention and training manuals for dementia care staff with clinical trial evidence of efficacy. Interventions were identified using a search of electronic databases, augmented by mainstream search engines, reference lists, hand searching for resources and consultation with an expert panel. The specific search for published manuals was complemented by a search for randomised control trials focussing on training and activity-based interventions for people with dementia in care homes. Manuals were screened for eligibility and rated to assess their quality, relevance and feasibility. A meta-analysis of randomised control trials indicated that person-centred training interventions conferred significant benefit in improving agitation and reducing the use of antipsychotics. Each of the efficacious packages included a sustained period of joint working and supervision with a trained mental health professional in addition to an educational element. However, of the 170 manuals that were identified, 30 met the quality criteria and only four had been evaluated in clinical trials. Despite the availability of a small number of evidence-based training manuals, there is a widespread use of person-centred intervention and training manuals that are not evidence-based. Clearer guidance is needed to ensure that commissioned training and interventions are based on robust evidence. Copyright © 2014 John Wiley & Sons, Ltd.

An analysis of the process and results of manual geocode correction

PubMed Central

McDonald, Yolanda J.; Schwind, Michael; Goldberg, Daniel W.; Lampley, Amanda; Wheeler, Cosette M.

2018-01-01

Geocoding is the science and process of assigning geographical coordinates (i.e. latitude, longitude) to a postal address. The quality of the geocode can vary dramatically depending on several variables, including incorrect input address data, missing address components, and spelling mistakes. A dataset with a considerable number of geocoding inaccuracies can potentially result in an imprecise analysis and invalid conclusions. There has been little quantitative analysis of the amount of effort (i.e. time) to perform geocoding correction, and how such correction could improve geocode quality type. This study used a low-cost and easy to implement method to improve geocode quality type of an input database (i.e. addresses to be matched) through the processes of manual geocode intervention, and it assessed the amount of effort to manually correct inaccurate geocodes, reported the resulting match rate improvement between the original and the corrected geocodes, and documented the corresponding spatial shift by geocode quality type resulting from the corrections. Findings demonstrated that manual intervention of geocoding resulted in a 90% improvement of geocode quality type, took 42 hours to process, and the spatial shift ranged from 0.02 to 151,368 m. This study provides evidence to inform research teams considering the application of manual geocoding intervention that it is a low-cost and relatively easy process to execute. PMID:28555477

Motor Development: Manual of Alternative Procedures.

ERIC Educational Resources Information Center

McCormack, James E.

The manual of alternative procedures for teaching handicapped children focuses on programming, planning, and implementing training in the gross motor (posture, limb control, locomotion) and fine motor (facial, digital) skills. The manual consists of the following sections: specific teaching tactics commonly used in motor training stiuations…

Applicator Training Manual for: Aquatic Weed Control.

ERIC Educational Resources Information Center

Herron, James W.

The aquatic weeds discussed in this manual include algae, floating weeds, emersed weeds, and submerged weeds. Specific requirements for pesticide application are given for static water, limited flow, and moving water situations. Secondary effects of improper application rates and faulty application are described. Finally, techniques of limited…

49 CFR 236.1039 - Operations and Maintenance Manual.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Operations and Maintenance Manual. 236.1039... Train Control Systems § 236.1039 Operations and Maintenance Manual. (a) The railroad shall catalog and..., modification, inspection, and testing of the PTC system and have them in one Operations and Maintenance Manual...

40 CFR 75.21 - Quality assurance and quality control requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Quality assurance and quality control... PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Operation and Maintenance Requirements § 75.21 Quality assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner or...

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 2 2013-07-01 2013-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 2 2010-07-01 2010-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 2 2011-07-01 2011-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 2 2012-07-01 2012-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

Manual for a Volunteer Services System.

ERIC Educational Resources Information Center

Helgerson, Linda; And Others

This manual presents guidelines for planning, monitoring, and controlling the development and operation of volunteer assistance programs. The materials included address questions related to both the process of establishing a volunteer program and the administration of a volunteer management system. The manual is not intended to provide a blueprint…

21 CFR 886.1770 - Manual refractor.

Code of Federal Regulations, 2010 CFR

2010-04-01

... DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1770 Manual refractor. (a) Identification. A manual refractor is a device that is a set of lenses of varous dioptric powers intended to measure the refractive error of the eye. (b) Classification. Class I (general controls). The device is exempt from the...

Quality control in gastrointestinal surgery.

PubMed

Ramírez-Barba, Ector Jaime; Arenas-Moya, Diego; Vázquez-Guerrero, Arturo

2011-01-01

We analyzed the Mexican legal framework, identifying the vectors that characterize quality and control in gastrointestinal surgery. Quality is contemplated in the health protection rights determined according to the Mexican Constitution, established in the general health law and included as a specific goal in the actual National Development Plan and Health Sector Plan. Quality control implies planning, verification and application of corrective measures. Mexico has implemented several quality strategies such as certification of hospitals and regulatory agreements by the General Salubrity Council, creation of the National Health Quality Committee, generation of Clinical Practice Guidelines and the Certification of Medical Specialties, among others. Quality control in gastrointestinal surgery must begin at the time of medical education and continue during professional activities of surgeons, encouraging multidisciplinary teamwork, knowledge, abilities, attitudes, values and skills that promote homogeneous, safe and quality health services for the Mexican population.

NV/YMP radiological control manual, Revision 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gile, A.L.

The Nevada Test Site (NTS) and the adjacent Yucca Mountain Project (YMP) are located in Nye County, Nevada. The NTS has been the primary location for testing nuclear explosives in the continental US since 1951. Current activities include operating low-level radioactive and mixed waste disposal facilities for US defense-generated waste, assembly/disassembly of special experiments, surface cleanup and site characterization of contaminated land areas, and non-nuclear test operations such as controlled spills of hazardous materials at the hazardous Materials (HAZMAT) Spill Center (HSC). Currently, the major potential for occupational radiation exposure is associated with the burial of low-level nuclear waste andmore » the handling of radioactive sources. Planned future remediation of contaminated land areas may also result in radiological exposures. The NV/YMP Radiological Control Manual, Revision 2, represents DOE-accepted guidelines and best practices for implementing Nevada Test Site and Yucca Mountain Project Radiation Protection Programs in accordance with the requirements of Title 10 Code of Federal Regulations Part 835, Occupational Radiation Protection. These programs provide protection for approximately 3,000 employees and visitors annually and include coverage for the on-site activities for both personnel and the environment. The personnel protection effort includes a DOE Laboratory Accreditation Program accredited dosimetry and personnel bioassay programs including in-vivo counting, routine workplace air sampling, personnel monitoring, and programmatic and job-specific As Low as Reasonably Achievable considerations.« less

Time series modeling of human operator dynamics in manual control tasks

NASA Technical Reports Server (NTRS)

Biezad, D. J.; Schmidt, D. K.

1984-01-01

A time-series technique is presented for identifying the dynamic characteristics of the human operator in manual control tasks from relatively short records of experimental data. Control of system excitation signals used in the identification is not required. The approach is a multi-channel identification technique for modeling multi-input/multi-output situations. The method presented includes statistical tests for validity, is designed for digital computation, and yields estimates for the frequency responses of the human operator. A comprehensive relative power analysis may also be performed for validated models. This method is applied to several sets of experimental data; the results are discussed and shown to compare favorably with previous research findings. New results are also presented for a multi-input task that has not been previously modeled to demonstrate the strengths of the method.

Time Series Modeling of Human Operator Dynamics in Manual Control Tasks

NASA Technical Reports Server (NTRS)

Biezad, D. J.; Schmidt, D. K.

1984-01-01

A time-series technique is presented for identifying the dynamic characteristics of the human operator in manual control tasks from relatively short records of experimental data. Control of system excitation signals used in the identification is not required. The approach is a multi-channel identification technique for modeling multi-input/multi-output situations. The method presented includes statistical tests for validity, is designed for digital computation, and yields estimates for the frequency response of the human operator. A comprehensive relative power analysis may also be performed for validated models. This method is applied to several sets of experimental data; the results are discussed and shown to compare favorably with previous research findings. New results are also presented for a multi-input task that was previously modeled to demonstrate the strengths of the method.

Comparison of anaesthetic gas consumption and stability of anaesthesia using automatic and manual control over the course of anaesthesia.

PubMed

Skalec, Tomasz; Górecka-Dolny, Agnieszka; Zieliński, Stanisław; Gibek, Mirosław; Stróżecki, Łukasz; Kübler, Andrzej

2017-01-01

The automatic control module of end-tidal volatile agents (EtC) was designed to reduce the consumption of anaesthetic gases, increase the stability of general anaesthesia and reduce the need for adjustments in the settings of the anaesthesia machine. The aim of this study was to verify these hypotheses. The course of general anaesthesia with the use of the EtC module was analysed for haemodynamic stability, depth of anaesthesia, end-expiratory concentration of anaesthetic, number of ventilator key presses, fentanyl supply, consumption of volatile agents and anaesthesia and operation times. These data were compared with the data obtained during general anaesthesia controlled manually and were processed with statistical tests. Seventy-four patients underwent general anaesthesia for scheduled operations. Group AUTO-ET (n = 35) was anaesthetized with EtC, and group MANUAL-ET (n = 39) was controlled manually. Both populations presented similar anaesthesia stability. No differences were noted in the time of anaesthesia, saturation up to MAC 1.0 or awakening. Data revealed no differences in mean EtAA or the fentanyl dose. The AUTO-ET group exhibited fewer key presses per minute, 0.0603 min⁻¹, whereas the MANUAL-ET exhibited a value of 0.0842 min⁻¹; P = 0.001. The automatic group consumed more anaesthetic and oxygen per minute (sevoflurane 0.1171 mL min⁻¹; IQR: 0.0503; oxygen 1.8286 mL min⁻¹, IQR: 1,3751) than MANUAL-ET (sevoflurane 0.0824 mL min⁻¹, IQR: 0.0305; oxygen 1,288 mL min⁻¹, IQR: 0,6517) (P = 0.0028 and P = 0.0171, respectively). Both methods are equally stable and safe for patients. The consumption of volatile agents was significantly increased in the AUTO-ET group. EtC considerably reduces the number of key presses.

Computer aided manual validation of mass spectrometry-based proteomic data.

PubMed

Curran, Timothy G; Bryson, Bryan D; Reigelhaupt, Michael; Johnson, Hannah; White, Forest M

2013-06-15

Advances in mass spectrometry-based proteomic technologies have increased the speed of analysis and the depth provided by a single analysis. Computational tools to evaluate the accuracy of peptide identifications from these high-throughput analyses have not kept pace with technological advances; currently the most common quality evaluation methods are based on statistical analysis of the likelihood of false positive identifications in large-scale data sets. While helpful, these calculations do not consider the accuracy of each identification, thus creating a precarious situation for biologists relying on the data to inform experimental design. Manual validation is the gold standard approach to confirm accuracy of database identifications, but is extremely time-intensive. To palliate the increasing time required to manually validate large proteomic datasets, we provide computer aided manual validation software (CAMV) to expedite the process. Relevant spectra are collected, catalogued, and pre-labeled, allowing users to efficiently judge the quality of each identification and summarize applicable quantitative information. CAMV significantly reduces the burden associated with manual validation and will hopefully encourage broader adoption of manual validation in mass spectrometry-based proteomics. Copyright © 2013 Elsevier Inc. All rights reserved.

Treating Small Bowel Obstruction with a Manual Physical Therapy: A Prospective Efficacy Study

PubMed Central

Rice, Amanda D.; Patterson, Kimberley; Reed, Evette D.; Wurn, Belinda F.; Klingenberg, Bernhard; King, C. Richard; Wurn, Lawrence J.

2016-01-01

Small bowel obstructions (SBOs) caused by adhesions are a common, often life-threatening postsurgical complication with few treatment options available for patients. This study examines the efficacy of a manual physical therapy treatment regimen on the pain and quality of life of subjects with a history of bowel obstructions due to adhesions in a prospective, controlled survey based study. Changes in six domains of quality of life were measured via ratings reported before and after treatment using the validated Small Bowel Obstruction Questionnaire (SBO-Q). Improvements in the domains for pain (p = 0.0087), overall quality of life (p = 0.0016), and pain severity (p = 0.0006) were significant when average scores before treatment were compared with scores after treatment. The gastrointestinal symptoms (p = 0.0258) domain was marginally significant. There was no statistically significant improvement identified in the diet or medication domains in the SBO-Q for this population. Significant improvements in range of motion in the trunk (p ≤ 0.001), often limited by adhesions, were also observed for all measures. This study demonstrates in a small number of subjects that this manual physical therapy protocol is an effective treatment option for patients with adhesive small bowel obstructions as measured by subject reported symptoms and quality of life. PMID:26989690

Modification of Motion Perception and Manual Control Following Short-Durations Spaceflight

NASA Technical Reports Server (NTRS)

Wood, S. J.; Vanya, R. D.; Esteves, J. T.; Rupert, A. H.; Clement, G.

2011-01-01

Adaptive changes during space flight in how the brain integrates vestibular cues with other sensory information can lead to impaired movement coordination and spatial disorientation following G-transitions. This ESA-NASA study was designed to examine both the physiological basis and operational implications for disorientation and tilt-translation disturbances following short-duration spaceflights. The goals of this study were to (1) examine the effects of stimulus frequency on adaptive changes in motion perception during passive tilt and translation motion, (2) quantify decrements in manual control of tilt motion, and (3) evaluate vibrotactile feedback as a sensorimotor countermeasure.

General aviation fuel quality control

NASA Technical Reports Server (NTRS)

Poitz, H.

1983-01-01

Quality control measures for aviation gasoline, and some of the differences between quality control on avgas and mogas are discussed. One thing to keep in mind is that with motor gasoline you can always pull off to the side of the road. It's not so easy to do in an airplane. Consequently, there are reasons for having the tight specifications and the tight quality control measures on avgas as compared to motor gasoline.

Network-based production quality control

NASA Astrophysics Data System (ADS)

Kwon, Yongjin; Tseng, Bill; Chiou, Richard

2007-09-01

This study investigates the feasibility of remote quality control using a host of advanced automation equipment with Internet accessibility. Recent emphasis on product quality and reduction of waste stems from the dynamic, globalized and customer-driven market, which brings opportunities and threats to companies, depending on the response speed and production strategies. The current trends in industry also include a wide spread of distributed manufacturing systems, where design, production, and management facilities are geographically dispersed. This situation mandates not only the accessibility to remotely located production equipment for monitoring and control, but efficient means of responding to changing environment to counter process variations and diverse customer demands. To compete under such an environment, companies are striving to achieve 100%, sensor-based, automated inspection for zero-defect manufacturing. In this study, the Internet-based quality control scheme is referred to as "E-Quality for Manufacturing" or "EQM" for short. By its definition, EQM refers to a holistic approach to design and to embed efficient quality control functions in the context of network integrated manufacturing systems. Such system let designers located far away from the production facility to monitor, control and adjust the quality inspection processes as production design evolves.

Effectiveness of a controlled drinking self-help manual: one-year follow-up results.

PubMed

Heather, N; Robertson, I; MacPherson, B; Allsop, S; Fulton, A

1987-11-01

Following the description of six-month follow-up results by Heather et al. (1986), this article reports one-year follow-up for a cohort of media-recruited problem drinkers sent either a controlled drinking self-help manual or a general advice and information booklet. Among those remaining in the sample, mean reduction in drinking at six months had been retained at the one-year point. This stability of reduced consumption included respondents showing evidence of late dependence or high consumption at initial assessment. When respondents who had received other forms of treatment had been excluded, the results confirmed the superior effectiveness of the self-help manual in enabling problem drinkers to reduce consumption. Evidence for a superior outcome among respondents interviewed by telephone, rather than contacted solely by post, was again observed. Some limited evidence is presented as to the reliability and validity of self-reports of consumption in the main sample.

Incorporating Manual and Autonomous Code Generation

NASA Technical Reports Server (NTRS)

McComas, David

1998-01-01

Code can be generated manually or using code-generated software tools, but how do you interpret the two? This article looks at a design methodology that combines object-oriented design with autonomic code generation for attitude control flight software. Recent improvements in space flight computers are allowing software engineers to spend more time engineering the applications software. The application developed was the attitude control flight software for an astronomical satellite called the Microwave Anisotropy Probe (MAP). The MAP flight system is being designed, developed, and integrated at NASA's Goddard Space Flight Center. The MAP controls engineers are using Integrated Systems Inc.'s MATRIXx for their controls analysis. In addition to providing a graphical analysis for an environment, MATRIXx includes an autonomic code generation facility called AutoCode. This article examines the forces that shaped the final design and describes three highlights of the design process: (1) Defining the manual to autonomic code interface; (2) Applying object-oriented design to the manual flight code; (3) Implementing the object-oriented design in C.

Field Operations and Enforcement Manual for Air Pollution Control. Volume III: Inspection Procedures for Specific Industries.

ERIC Educational Resources Information Center

Weisburd, Melvin I.

The Field Operations and Enforcement Manual for Air Pollution Control, Volume III, explains in detail the following: inspection procedures for specific sources, kraft pulp mills, animal rendering, steel mill furnaces, coking operations, petroleum refineries, chemical plants, non-ferrous smelting and refining, foundries, cement plants, aluminum…

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 2 2014-07-01 2014-07-01 false Quality control. 51.359 Section 51.359 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS REQUIREMENTS FOR... to assure test accuracy. Computer control of quality assurance checks and quality control charts...

[A survey on diet manuals in Italian hospitals].

PubMed

Donini, L M; Riti, M; Castellaneta, E; Ceccarelli, P; Civale, C; Passaretti, S; del Balzo, V; Cannella, C

2009-01-01

Hospital catering is very important to counteract the onset of malnutrition due to either undernutrition or overnutrition and for dietetic treatment. The aim of the study was to evaluate nutritional quality of the hospital dietetic manual used in some Italian hospitals and to analyze the role of the institutional Catering Service and of the Department of Clinical Nutrition. A survey has been carried out, in some Italian hospitals, using a questionnaire to point out the characteristics of hospitals, the typology of catering service, of the diets and of the staff of the Department of Clinical Nutrition. Only 22% of the hospitals has answered; three Italian regions (Umbria, Molise, Basilicata) are completely missing; -each hospital has a specific dietetic manual in most cases completely different from structure and nutritional quality point of view; the staff acting in this field is absolutely insufficient in term of numerousness and of professional typologies. Hospital in-patients are not homogeneous as for age, dietary needs and diseases, so it's necessary to treat them with an ad hoc nutritional intervention not established in advance in a dietetic manual; if from an organisation point of view it is necessary to have such a dietetic manual, it has to be based on nutritional guidelines and recommended dietary allowances.

Manual lymphatic drainage therapy in patients with breast cancer related lymphoedema.

PubMed

Martín, Marta López; Hernández, Miguel A; Avendaño, Cristina; Rodríguez, Francisco; Martínez, Helena

2011-03-09

Lymphoedema is a common and troublesome condition that develops following breast cancer treatment. The aim of this study is to analyze the effectiveness of Manual Lymphatic Drainage in the treatment of postmastectomy lymphoedema in order to reduce the volume of lymphoedema and evaluate the improvement of the concomitant symptomatology. A randomized, controlled clinical trial in 58 women with post-mastectomy lymphoedema. The control group includes 29 patients with standard treatment (skin care, exercise and compression measures, bandages for one month and, subsequently, compression garments). The experimental group includes 29 patients with standard treatment plus Manual Lymphatic Drainage. The therapy will be administered daily for four weeks and the patient's condition will be assessed one, three and six months after treatment.The primary outcome parameter is volume reduction of the affected arm after treatment, expressed as a percentage. Secondary outcome parameters include: duration of lymphoedema reduction and improvement of the concomitant symptomatology (degree of pain, sensation of swelling and functional limitation in the affected extremity, subjective feeling of being physically less attractive and less feminine, difficulty looking at oneself naked and dissatisfaction with the corporal image). The results of this study will provide information on the effectiveness of Manual Lymphatic Drainage and its impact on the quality of life and physical limitations of these patients. ClinicalTrials (NCT): NCT01152099.

METRO-APEX Volume 9.1: Solid Waste Manager's Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The Solid Waste Manager's Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air Pollution…

METRO-APEX Volume 1.1: Game Overall Director's Manual. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The Game Overall Director's Manual is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of APEX--Air…

A comparison of the efficacy of powered and manual toothbrushes in controlling plaque and gingivitis: a clinical study

PubMed Central

Jain, Yashika

2013-01-01

Background Plaque is intimately related to the production and progress of dental caries and inflammatory gingival and periodontal diseases. Good plaque control facilitates the return to health for patients with gingival and periodontal diseases. Daily use of a toothbrush and other oral hygiene aids is the most dependable way to achieve oral health benefits for all patients. Methods A randomized clinical trial was conducted to compare the efficacy of a powered toothbrush with a manual toothbrush in controlling plaque and gingivitis over a 6-week period. The sample consisted of 60 dental students of both sexes, with ages ranging from 18 to 28 years. The samples were stratified and randomly divided into two groups of 30 by a second examiner using the coin toss method; one group used a manual toothbrush and the other group used a powered toothbrush. Each participant’s gingival index, plaque index and oral hygiene index were assessed on the seventh, 14th, and 45th days on the basis of the assigned toothbrush. Collected data were analyzed and different subgroups were compared using Student’s t-test. Results A paired t-test revealed a highly significant reduction in the gingival, plaque, and oral hygiene index scores of the manual and powered groups at the first, second, and sixth weeks (P-value < 0.0001). An unpaired t-test revealed a significant reduction between the plaque index scores of the manual and powered groups at the second week (P-value < 0.05). Another unpaired t-test revealed a highly significant reduction between the plaque index scores of the manual and powered groups at the sixth week (P-value < 0.0001). Conclusion The subject group using the powered toothbrush demonstrated clinical and statistical improvement in overall plaque scores. Powered toothbrushes offer an individual the ability to brush the teeth in a way that is optimal in terms of removing plaque and improving gingival health, conferring good brushing technique on all who use them

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

Asphalt Raking. Instructor Manual. Trainee Manual.

ERIC Educational Resources Information Center

Laborers-AGC Education and Training Fund, Pomfret Center, CT.

This packet consists of the instructor and trainee manuals for an asphalt raking course. The instructor manual contains a course schedule for 4 days of instruction, content outline, and instructor outline. The trainee manual is divided into five sections: safety, asphalt basics, placing methods, repair and patching, and clean-up and maintenance.…

A Manual Control Test for the Detection and Deterrence of Impaired Drivers

NASA Technical Reports Server (NTRS)

Stein, A. C.; Allen, R. W.; Jex, H. R.

1984-01-01

A brief manual control test and a decision strategy were developed, laboratory tested, and field validated which provide a means for detecting human operator impairment from alcohol or other drugs. The test requires the operator to stabilize progressively unstable controlled element dynamics. Control theory and experimental data verify that the human operator's control ability on this task is constrained by basic cybernetic characteristics, and that task performance is reliably affected by impairment effects on these characteristics. Assessment of human operator control ability is determined by a statistically based decision strategy. The operator is allowed several chances to exceed a preset pass criterion. Procedures are described for setting the pass criterion based on individual ability and a desired unimpaired failure rate. These procedures were field tested with apparatus installed in automobiles that were designed to discourage drunk drivers from operating their vehicles. This test program demonstrated that the control task and detection strategy could be applied in a practical setting to screen human operators for impairment in their basic cybernetic skills.

A Brief Manualized Treatment for Problematic Caffeine Use: A Randomized Control Trial

PubMed Central

Evatt, Daniel P.; Juliano, Laura M.; Griffiths, Roland R.

2015-01-01

Objective The goal of the present investigation was to develop and test a brief therapist-guided manualized treatment for problematic caffeine use including cognitive-behavioral strategies and 5-weeks of progressively decreased consumption. Methods Individuals seeking treatment for problematic caffeine use (mean daily caffeine consumption of 666.0 mg at baseline) were randomized using a waitlist-control design to receive immediate (N = 33) treatment or delayed (N = 34) treatment (∼6 weeks later). A one-hour long treatment session designed to help individuals quit or reduce caffeine consumption was provided by a trained counselor along with a take-home booklet. After the treatment session, participants completed daily diaries of caffeine consumption for 5 weeks. They returned for follow-up assessments at 6, 12, and 26 weeks and had a telephone interview at 52-weeks post-treatment. Results Treatment resulted in a significant reduction in self reported caffeine use and salivary caffeine levels. No significant post-treatment increases in caffeine use were observed for up to one year follow-up. Comparisons to the waitlist control condition revealed that reductions in caffeine consumption were due to treatment and not the passing of time, with a treatment effect size of R2 = .35 for the model. Conclusions A brief one-session manualized intervention with follow-up was efficacious at reducing caffeine consumption. Future research should replicate and extend these findings, as well as consider factors affecting dissemination of treatment for problematic caffeine use to those in need. PMID:26501499

Dual Extended Kalman Filter for the Identification of Time-Varying Human Manual Control Behavior

NASA Technical Reports Server (NTRS)

Popovici, Alexandru; Zaal, Peter M. T.; Pool, Daan M.

2017-01-01

A Dual Extended Kalman Filter was implemented for the identification of time-varying human manual control behavior. Two filters that run concurrently were used, a state filter that estimates the equalization dynamics, and a parameter filter that estimates the neuromuscular parameters and time delay. Time-varying parameters were modeled as a random walk. The filter successfully estimated time-varying human control behavior in both simulated and experimental data. Simple guidelines are proposed for the tuning of the process and measurement covariance matrices and the initial parameter estimates. The tuning was performed on simulation data, and when applied on experimental data, only an increase in measurement process noise power was required in order for the filter to converge and estimate all parameters. A sensitivity analysis to initial parameter estimates showed that the filter is more sensitive to poor initial choices of neuromuscular parameters than equalization parameters, and bad choices for initial parameters can result in divergence, slow convergence, or parameter estimates that do not have a real physical interpretation. The promising results when applied to experimental data, together with its simple tuning and low dimension of the state-space, make the use of the Dual Extended Kalman Filter a viable option for identifying time-varying human control parameters in manual tracking tasks, which could be used in real-time human state monitoring and adaptive human-vehicle haptic interfaces.

Orion Handling Qualities During ISS Proximity Operations and Docking

NASA Technical Reports Server (NTRS)

Stephens, John-Paul; Vos, Gordon A.; Bilimoria, Karl D.; Mueller, Eric R.; Brazzel, Jack; Spehar, Pete

2011-01-01

NASA's Orion spacecraft is designed to autonomously rendezvous and dock with many vehicles including the International Space Station. However, the crew is able to assume manual control of the vehicle s attitude and flight path. In these instances, Orion must meet handling qualities requirements established by NASA. Two handling qualities assessments were conducted at the Johnson Space Center to evaluate preliminary designs of the vehicle using a six degree of freedom, high-fidelity guidance, navigation, and control simulation. The first assessed Orion s handling qualities during the last 20 ft before docking, and included both steady and oscillatory motions of the docking target. The second focused on manual acquisition of the docking axis during the proximity operations phase and subsequent station-keeping. Cooper-Harper handling qualities ratings, workload ratings and comments were provided by 10 evaluation pilots for the docking study and 5 evaluation pilots for the proximity operations study. For the docking task, both cases received 90% Level 1 (satisfactory) handling qualities ratings, exceeding NASA s requirement. All ratings for the ProxOps task were Level 1. These evaluations indicate that Orion is on course to meet NASA's handling quality requirements for ProxOps and docking.

7 CFR 930.44 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

7 CFR 930.44 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

7 CFR 930.44 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

7 CFR 930.44 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

Aircraft noise prediction program user's manual

NASA Technical Reports Server (NTRS)

Gillian, R. E.

1982-01-01

The Aircraft Noise Prediction Program (ANOPP) predicts aircraft noise with the best methods available. This manual is designed to give the user an understanding of the capabilities of ANOPP and to show how to formulate problems and obtain solutions by using these capabilities. Sections within the manual document basic ANOPP concepts, ANOPP usage, ANOPP functional modules, ANOPP control statement procedure library, and ANOPP permanent data base. appendixes to the manual include information on preparing job decks for the operating systems in use, error diagnostics and recovery techniques, and a glossary of ANOPP terms.

A review of manual wheelchairs.

PubMed

Flemmer, Claire L; Flemmer, Rory C

2016-01-01

To review the scientific literature published in the last 14 years on the different types of manual wheelchairs. A systematic review of the literature was conducted to find the recent research on manual wheelchairs. The findings of 77 references on pushrim-propelled wheelchairs, crank-propelled wheelchairs, lever-propelled wheelchairs, geared manual wheelchairs and pushrim-activated power-assist wheelchairs are reported. The pushrim-propelled wheelchair is light, easy to steer and has good indoor manoeuvrability but is very inefficient and causes serious upper body overloading so that long-term use leads to steadily deteriorating capability for the user and ultimately a transition to a powered chair. Whilst the latter is less physically demanding, the sedentary lifestyle and decreasing muscle use lead to several secondary health problems. Crank- and lever-propelled wheelchairs and geared pushrim wheelchairs are more efficient and less demanding and may improve the quality of life of the user by expanding the range of accessible environments, reducing upper body pain, increasing independence and avoiding or delaying the 'debilitating cycle'. However, wheelchairs with these alternative modes of propulsion are often heavier, wider and/or longer and are less easy to steer, brake and fold than the pushrim wheelchair. Implications for rehabilitation Pushrim-propelled wheelchairs are difficult to drive on outdoor paths (grass and gravel/sand surfaces) and ramps so that users are confined to restricted environments and have limited participation in everyday activities. The repetitive strain imposed on the upper body by pushrim propulsion leads to very high prevalence of shoulder and wrist pain in manual wheelchair users. Crank-propelled and lever-propelled wheelchairs are more efficient and less straining than pushrim propelled wheelchairs, allowing users to access more challenging environments, prolong independence and improve the quality of life.

Novice, seasoned and veteran counselors' views of addiction treatment manuals: the influence of counselor characteristics on manual usefulness.

PubMed

Simons, Lori; Jacobucci, Raymond; Houston, Hank

2006-12-01

A preliminary study was conducted to examine substance abuse counselors' views of empirically supported treatments (ESTs). A survey of 72 substance abuse counselors was used to explore counselor qualities and overall responses to ESTs. There were no significant differences in views of ESTs for novice, seasoned and veteran counselors, but veteran counselors reported that supervision was less likely to influence their views of manual usefulness. Counselors' recovery status and theoretical orientation influenced novice, seasoned and veteran counselors' views of ESTs and manual usefulness. Implications for undergraduate, graduate and continuing education are discussed.

Oral Rehydration Therapy and the Control of Diarrheal Diseases. Training for Development. Peace Corps Information Collection & Exchange Training Manual No. T-34.

ERIC Educational Resources Information Center

Clark, Mari; And Others

This manual was developed to train Peace Corps volunteers and other community health workers in oral rehydration therapy (ORT) and the control of diarrheal diseases. Using a competency-based format, the manual contains six training modules (organized in 22 sessions) that focus on interrelated health education and technical content areas. Each…

14 CFR 21.139 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Quality control. 21.139 Section 21.139... PROCEDURES FOR PRODUCTS AND PARTS Production Certificates § 21.139 Quality control. The applicant must show that he has established and can maintain a quality control system for any product, for which he...

33 CFR 385.21 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Quality control. 385.21 Section... Processes § 385.21 Quality control. (a) The Corps of Engineers and the non-Federal sponsor shall prepare a quality control plan, in accordance with applicable Corps of Engineers regulations, for each product that...

14 CFR 21.139 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Quality control. 21.139 Section 21.139... PROCEDURES FOR PRODUCTS AND PARTS Production Certificates § 21.139 Quality control. The applicant must show that he has established and can maintain a quality control system for any product, for which he...

33 CFR 385.21 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Quality control. 385.21 Section... Processes § 385.21 Quality control. (a) The Corps of Engineers and the non-Federal sponsor shall prepare a quality control plan, in accordance with applicable Corps of Engineers regulations, for each product that...

33 CFR 385.21 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Quality control. 385.21 Section... Processes § 385.21 Quality control. (a) The Corps of Engineers and the non-Federal sponsor shall prepare a quality control plan, in accordance with applicable Corps of Engineers regulations, for each product that...

Advanced figure sensor operations and maintenance manual

NASA Technical Reports Server (NTRS)

Robertson, H. J.

1972-01-01

This manual contains procedures for installing, operating, and maintaining the optical figure sensor and its associated electronic controls. The optical figure sensor, a system of integrated components, comprises: (1) a phase measuring modified interferometer employing a single frequency 6328 A laser, and a Vidissector; (2) a two-axis automatic thermal compensation control mount; (3) a five degree of freedom manual adjustment stand; and (4) a control console. This instrument provides real time output data of optical figure errors for spherical mirrors, and is also capable of measuring aspherical mirrors if a null corrector is added.

Storm Water Management Model Applications Manual

EPA Science Inventory

The EPA Storm Water Management Model (SWMM) is a dynamic rainfall-runoff simulation model that computes runoff quantity and quality from primarily urban areas. This manual is a practical application guide for new SWMM users who have already had some previous training in hydrolog...

Manual Therapy in the Treatment of Idiopathic Scoliosis. Analysis of Current Knowledge.

PubMed

Czaprowski, Dariusz

2016-10-28

Apart from the recommended specific physiotherapy, the treatment of idiopathic scoliosis (IS) also incorporates non-specific manual therapy (NMT). The aim of this paper is to assess the efficacy of NMT (manual therapy, chiropractic, osteopathy) used in the treatment of children and adolescents with IS. The study analysed systematic reviews (Analysis 1) and other recent scientific publications (Analysis 2). Analysis 1 encompassed papers on the use of NMT in patients with IS. Works concerning specific physiotherapy (SP) or bracing (B) and other types of scoliosis were excluded from the analysis. Inclusion criteria for Analysis 2 were: treatment with NMT; subjects aged 10-18 years with IS. The following types of papers were excluded: works analysing NMT combined with SP or B, reports concerning adult pa tients, analyses of single cases and publications included in Analysis 1. Analysis 1: six systematic reviews contained 6 papers on the efficacy of NMT in the treatment of IS. The results of these studies are contradictory, ranging from Cobb angle reduction to no treatment effects whatsoever. The papers analysed are characterised by poor methodological quality: small group sizes, incomplete descriptions of the study groups, no follow-up and no control groups. Analysis 2: in total, 217 papers were found. None of them met the criteria set for the analysis. 1. Few papers verifying the efficacy of manual therapy, chiropractic and osteopathy in the treatment of idiopathic scoliosis have been published to date. 2. The majority are experimental studies with poor methodology or observational case studies. 3. At present, the efficacy of non-specific manual therapy in the treatment of patients with idiopathic scoliosis cannot be reliably evaluated. 4. It is necessary to conduct further research based on appropriate methods (prospective, rando mi s ed, controlled studies) in order to reliably assess the usefulness of non-specific manual therapy in the treatment of idiopathic

A randomized controlled trial of a manual-based psychosocial group intervention for young people with epilepsy [PIE].

PubMed

Dorris, Liam; Broome, Helen; Wilson, Margaret; Grant, Cathy; Young, David; Baker, Gus; Balloo, Selina; Bruce, Susan; Campbell, Jo; Concannon, Bernie; Conway, Nadia; Cook, Lisa; Davis, Cheryl; Downey, Bruce; Evans, Jon; Flower, Diane; Garlovsky, Jack; Kearney, Shauna; Lewis, Susan; Stephens, Victoria; Turton, Stuart; Wright, Ingram

2017-07-01

We conducted an exploratory RCT to examine feasibility and preliminary efficacy for a manual-based psychosocial group intervention aimed at improving epilepsy knowledge, self-management skills, and quality of life in young people with epilepsy. Eighty-three participants (33:50m/f; age range 12-17years) were randomized to either the treatment or control group in seven tertiary paediatric neuroscience centres in the UK, using a wait-list control design. Participants were excluded if they reported suicidal ideation and/or scored above the cut off on mental health screening measures, or if they had a learning disability or other neurological disorder. The intervention consisted of six weekly 2-hour sessions using guided discussion, group exercises and role-plays facilitated by an epilepsy nurse and a clinical psychologist. At three month follow up the treatment group (n=40) was compared with a wait-list control group (n=43) on a range of standardized measures. There was a significant increase in epilepsy knowledge in the treatment group (p=0.02). Participants receiving the intervention were also significantly more confident in speaking to others about their epilepsy (p=0.04). Quality of life measures did not show significant change. Participants reported the greatest value of attending the group was: Learning about their epilepsy (46%); Learning to cope with difficult feelings (29%); and Meeting others with epilepsy (22%). Caregiver and facilitator feedback was positive, and 92% of participants would recommend the group to others. This brief psychosocial group intervention was effective in increasing participants' knowledge of epilepsy and improved confidence in discussing their epilepsy with others. We discuss the qualitative feedback, feasibility, strengths and limitations of the PIE trial. Copyright © 2017 Elsevier Inc. All rights reserved.

40 CFR 136.7 - Quality assurance and quality control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality control elements, where applicable, into the laboratory's documented standard operating procedure... quality control elements must be clearly documented in the written standard operating procedure for each... Methods contains QA/QC procedures in the Part 1000 section of the Standard Methods Compendium. The...

40 CFR 136.7 - Quality assurance and quality control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality control elements, where applicable, into the laboratory's documented standard operating procedure... quality control elements must be clearly documented in the written standard operating procedure for each... Methods contains QA/QC procedures in the Part 1000 section of the Standard Methods Compendium. The...

40 CFR 136.7 - Quality assurance and quality control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality control elements, where applicable, into the laboratory's documented standard operating procedure... quality control elements must be clearly documented in the written standard operating procedure for each... Methods contains QA/QC procedures in the Part 1000 section of the Standard Methods Compendium. The...

46 CFR 161.002-12 - Manual fire alarm systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the control unit and terminating at manual fire alarm boxes. Power failure alarm devices may be... specifically approved. (b) Types. Manual fire alarm systems shall be one of the following types, or a... using manually operated fire alarm boxes. (3) Other types as may be developed. (c) Power supply. The...

46 CFR 161.002-12 - Manual fire alarm systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the control unit and terminating at manual fire alarm boxes. Power failure alarm devices may be... specifically approved. (b) Types. Manual fire alarm systems shall be one of the following types, or a... using manually operated fire alarm boxes. (3) Other types as may be developed. (c) Power supply. The...

46 CFR 161.002-12 - Manual fire alarm systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the control unit and terminating at manual fire alarm boxes. Power failure alarm devices may be... specifically approved. (b) Types. Manual fire alarm systems shall be one of the following types, or a... using manually operated fire alarm boxes. (3) Other types as may be developed. (c) Power supply. The...

Kepler Archive Manual

NASA Technical Reports Server (NTRS)

Thompson, Susan E.; Fraquelli, Dorothy; Van Cleve, Jeffrey E.; Caldwell, Douglas A.

2016-01-01

A description of Kepler, its design, performance and operational constraints may be found in the Kepler Instrument Handbook (KIH, Van Cleve Caldwell 2016). A description of Kepler calibration and data processing is described in the Kepler Data Processing Handbook (KDPH, Jenkins et al. 2016; Fanelli et al. 2011). Science users should also consult the special ApJ Letters devoted to early Kepler results and mission design (April 2010, ApJL, Vol. 713 L79-L207). Additional technical details regarding the data processing and data qualities can be found in the Kepler Data Characteristics Handbook (KDCH, Christiansen et al. 2013) and the Data Release Notes (DRN). This archive manual specifically documents the file formats, as they exist for the last data release of Kepler, Data Release 25(KSCI-19065-002). The earlier versions of the archive manual and data release notes act as documentation for the earlier versions of the data files.

Manual vs. computer-assisted sperm analysis: can CASA replace manual assessment of human semen in clinical practice?

PubMed

Talarczyk-Desole, Joanna; Berger, Anna; Taszarek-Hauke, Grażyna; Hauke, Jan; Pawelczyk, Leszek; Jedrzejczak, Piotr

2017-01-01

The aim of the study was to check the quality of computer-assisted sperm analysis (CASA) system in comparison to the reference manual method as well as standardization of the computer-assisted semen assessment. The study was conducted between January and June 2015 at the Andrology Laboratory of the Division of Infertility and Reproductive Endocrinology, Poznań University of Medical Sciences, Poland. The study group consisted of 230 men who gave sperm samples for the first time in our center as part of an infertility investigation. The samples underwent manual and computer-assisted assessment of concentration, motility and morphology. A total of 184 samples were examined twice: manually, according to the 2010 WHO recommendations, and with CASA, using the program set-tings provided by the manufacturer. Additionally, 46 samples underwent two manual analyses and two computer-assisted analyses. The p-value of p < 0.05 was considered as statistically significant. Statistically significant differences were found between all of the investigated sperm parameters, except for non-progressive motility, measured with CASA and manually. In the group of patients where all analyses with each method were performed twice on the same sample we found no significant differences between both assessments of the same probe, neither in the samples analyzed manually nor with CASA, although standard deviation was higher in the CASA group. Our results suggest that computer-assisted sperm analysis requires further improvement for a wider application in clinical practice.

PREVENTION REFERENCE MANUAL: CHEMICAL SPECIFIC. VOLUME 2. CONTROL OF ACCIDENTAL RELEASES OF CHLORINE (SCAQMD) (SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT)

EPA Science Inventory

The manual discusses reducing the risk associated with an accidental release of chlorine. It identifies some of the potential causes of accidental releases that apply to the processes that use chlorine. It also identifies examples of potential causes, as well as measures that may...

Pre-Statistical Process Control: Making Numbers Count! JobLink Winning at Work Instructor's Manual, Module 3.

ERIC Educational Resources Information Center

Coast Community Coll. District, Costa Mesa, CA.

This instructor's manual for workplace trainers contains the materials required to conduct a course in pre-statistical process control. The course consists of six lessons for workers and two lessons for supervisors that discuss the following: concepts taught in the six lessons; workers' progress in the individual lessons; and strategies for…

The manual control of vehicles undergoing slow transitions in dynamic characteristics

NASA Technical Reports Server (NTRS)

Moriarty, T. E.

1974-01-01

The manual control was studied of a vehicle with slowly time-varying dynamics to develop analytic and computer techniques necessary for the study of time-varying systems. The human operator is considered as he controls a time-varying plant in which the changes are neither abrupt nor so slow that the time variations are unimportant. An experiment in which pilots controlled the longitudinal mode of a simulated time-varying aircraft is described. The vehicle changed from a pure double integrator to a damped second order system, either instantaneously or smoothly over time intervals of 30, 75, or 120 seconds. The regulator task consisted of trying to null the error term resulting from injected random disturbances with bandwidths of 0.8, 1.4, and 2.0 radians per second. Each of the twelve experimental conditons was replicated ten times. It is shown that the pilot's performance in the time-varying task is essentially equivalent to his performance in stationary tasks which correspond to various points in the transition. A rudimentary model for the pilot-vehicle-regulator is presented.

QUALITY CONTROL OF PHARMACEUTICALS.

PubMed

LEVI, L; WALKER, G C; PUGSLEY, L I

1964-10-10

Quality control is an essential operation of the pharmaceutical industry. Drugs must be marketed as safe and therapeutically active formulations whose performance is consistent and predictable. New and better medicinal agents are being produced at an accelerated rate. At the same time more exacting and sophisticated analytical methods are being developed for their evaluation. Requirements governing the quality control of pharmaceuticals in accordance with the Canadian Food and Drugs Act are cited and discussed.

46 CFR 161.002-12 - Manual fire alarm systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... (a) General. A manual fire alarm system shall consist of a power supply, a control unit on which are... using manually operated fire alarm boxes. (3) Other types as may be developed. (c) Power supply. The power supply shall be as specified for automatic fire detecting system by § 161.002-9. (d) Manual fire...

46 CFR 161.002-12 - Manual fire alarm systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

.... (a) General. A manual fire alarm system shall consist of a power supply, a control unit on which are... using manually operated fire alarm boxes. (3) Other types as may be developed. (c) Power supply. The power supply shall be as specified for automatic fire detecting system by § 161.002-9. (d) Manual fire...

Trickling Filters. Student Manual. Biological Treatment Process Control.

ERIC Educational Resources Information Center

Richwine, Reynold D.

The textual material for a unit on trickling filters is presented in this student manual. Topic areas discussed include: (1) trickling filter process components (preliminary treatment, media, underdrain system, distribution system, ventilation, and secondary clarifier); (2) operational modes (standard rate filters, high rate filters, roughing…

Manual of good practices for sanitation in coal mining operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The purpose of the manual was to act as a guideline, setting reasonable recommendations relative to mine sanitation which will enable mines to install adequate facilities and make appropriate alterations conserving and improving the health and welfare of the mine worker. A systematic evaluation was undertaken of the sanitation facilities and maintenance at coal mines. Consideration was given to central facilities including building, floors, walls, partitions, ceilings, lockers, baskets and benches, showers, toilets, lavatories, lighting, ventilation and temperature control, and maintenance. Also discussed were food vending machines, water source, water quality, water treatment, water delivery systems for underground and surfacemore » mines, sanitary waste disposal, workplace toilets in underground and surface mines, refuse control and handling for underground and surface mines, and pest control.« less

7 CFR 58.928 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be...

Expert database system for quality control

NASA Astrophysics Data System (ADS)

Wang, Anne J.; Li, Zhi-Cheng

1993-09-01

There are more competitors today. Markets are not homogeneous they are fragmented into increasingly focused niches requiring greater flexibility in the product mix shorter manufacturing production runs and above allhigher quality. In this paper the author identified a real-time expert system as a way to improve plantwide quality management. The quality control expert database system (QCEDS) by integrating knowledge of experts in operations quality management and computer systems use all information relevant to quality managementfacts as well as rulesto determine if a product meets quality standards. Keywords: expert system quality control data base

Effectiveness of Plaque Control with Novel Pediatric Oral Hygiene Need Station (Modified Oral Irrigation Device) as Compared with Manual Brushing and Flossing: Randomized Controlled Pilot Trial.

PubMed

Murthy, Prashanth Sadashiva; Shaik, Naseemoon; Deshmukh, Seema; Girish, M S

2018-01-01

Establishing good hygiene habits are valuable for present and future oral health. Below 6 years, tooth brushing should be performed by parents, as increasing dexterity and cognition may permit supervised brushing until the child is capable of independent brushing. The aim of the present study was to evaluate the effectiveness of modified oral irrigation device in children in terms of plaque control and to compare the effectiveness of plaque control with manual brushing with the modified oral irrigation device in children. A randomized clinical trial was performed on 12 subjects who were allocated to the two study groups. After obtaining the consent, the control group was instructed tooth brushing with regular pediatric commercially available toothbrush and the intervention group with modified oral irrigation device. Plaque scores in both groups were assessed pre- and post-brushing using modified navy plaque index. The data were subjected to Descriptive statistics and Paired t -test using SPSS version 22. Intragroup comparison of mean difference of plaque score in control group and intervention group pre- and post-brushing was statistically significant. Intergroup comparison of manual brushing group with modified oral irrigation group shows P < 0.05 was statistically significant. Within the limitation of the present study, it has been found novel pediatric oral hygiene need Station is more effective than manual brushing since it combined the effect of brushing, flossing (water floss), and rinsing in children simultaneously and at the same time did not demand any special motor skill.

7 CFR 58.335 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.335 Section 58.335... Procedures § 58.335 Quality control tests. All milk, cream and related products are subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow...

Initial development of a device for controlling manually applied forces.

PubMed

Waddington, Gordon S; Adams, Roger D

2007-05-01

In both simulation and manual therapy studies, substantial variability has been shown when therapists attempt to replicate an applied force. Knowledge about the forces employed during treatment could reduce this variability. In the current project, a prototype for a mobilizing device incorporating a dynamometer was constructed. The prototype device was built around a conventional "hand-grip" dynamometer to give dial visibility during application of mobilizing forces and a moulded handle was used to increase the hand contact surface during force application. The variability of the mobilization forces produced was measured, and ratings of comfort during a simulated spinal mobilization technique were obtained from therapists. Thirty physiotherapists were randomly allocated to apply either: (i) their own estimate of a grade III mobilization force using their hands in a pisiform grip or (ii) a 100N force with the manual therapy dynamometer, and to rate comfort during the performance of both techniques on a 100mm visual analogue scale. Variance in dynamometer-dial-guided force application was always significantly less than the variance in therapist-concept-guided force application. Repeated-measures tests showed that the mean force produced at grade III was not significantly different from 100N, but physiotherapist comfort ratings were found to be significantly greater (P<0.01) when the manual therapy dynamometer was used. Manually applied force variability was significantly less and therapist comfort greater when using a device with visual access to a dial giving immediate force readout.

The Effectiveness and Safety of Manual Therapy on Pain and Disability in Older Persons With Chronic Low Back Pain: A Systematic Review.

PubMed

de Luca, Katie E; Fang, Sheng Hung; Ong, Justin; Shin, Ki-Soo; Woods, Samuel; Tuchin, Peter J

2017-09-01

The aim of this study was to perform a systematic review of the literature of the effectiveness and safety of manual therapy interventions on pain and disability in older persons with chronic low back pain (LBP). A literature search of 4 electronic databases was performed (PubMed, EMBASE, OVID, and CINAHL). Inclusion criteria included randomized controlled trials of manual therapy interventions on older persons who had chronic LBP. Effectiveness was determined by extracting and examining outcomes for pain and disability, with safety determined by the report of adverse events. The PEDro scale was used for quality assessment of eligible studies. The search identified 405 articles, and 38 full-text articles were assessed. Four studies met the inclusion criteria. All trials were of good methodologic quality and had a low risk of bias. The included studies provided moderate evidence supporting the use of manual therapy to reduce pain levels and alleviate disability. A limited number of studies have investigated the effectiveness and safety of manual therapy in the management of older people with chronic LBP. The current evidence to make firm clinical recommendations is limited. Research with appropriately designed trials to investigate the effectiveness and safety of manual therapy interventions in older persons with chronic LBP is required. Copyright © 2017. Published by Elsevier Inc.

WHO Working Group on revision of the Manual of Laboratory Methods for Testing DTP Vaccines-Report of two meetings held on 20-21 July 2006 and 28-30 March 2007, Geneva, Switzerland.

PubMed

Corbel, Michael J; Das, Rose Gaines; Lei, Dianliang; Xing, Dorothy K L; Horiuchi, Yoshinobu; Dobbelaer, Roland

2008-04-07

This report reflects the discussion and conclusions of a WHO group of experts from National Regulatory Authorities (NRAs), National Control Laboratories (NCLs), vaccine industries and other relevant institutions involved in standardization and control of diphtheria, tetanus and pertussis vaccines (DTP), held on 20-21 July 2006 and 28-30 March 2007, in Geneva Switzerland for the revision of WHO Manual for quality control of DTP vaccines. Taking into account recent developments and standardization in quality control methods and the revision of WHO recommendations for D, T, P vaccines, and a need for updating the manual has been recognized. In these two meetings the current situation of quality control methods in terms of potency, safety and identity tests for DTP vaccines and statistical analysis of data were reviewed. Based on the WHO recommendations and recent validation of testing methods, the content of current manual were reviewed and discussed. The group agreed that the principles to be observed in selecting methods included identifying those critical for assuring safety, efficacy and quality and which were consistent with WHO recommendations/requirements. Methods that were well recognized but not yet included in current Recommendations should be taken into account. These would include in vivo and/or in vitro methods for determining potency, safety testing and identity. The statistical analysis of the data should be revised and updated. It was noted that the mouse based assays for toxoid potency were still quite widely used and it was desirable to establish appropriate standards for these to enable the results to be related to the standard guinea pig assays. The working group was met again to review the first drafts and to input further suggestions or amendments to the contributions of the drafting groups. The revised manual was to be finalized and published by WHO.

Multi-level manual and autonomous control superposition for intelligent telerobot

NASA Technical Reports Server (NTRS)

Hirai, Shigeoki; Sato, T.

1989-01-01

Space telerobots are recognized to require cooperation with human operators in various ways. Multi-level manual and autonomous control superposition in telerobot task execution is described. The object model, the structured master-slave manipulation system, and the motion understanding system are proposed to realize the concept. The object model offers interfaces for task level and object level human intervention. The structured master-slave manipulation system offers interfaces for motion level human intervention. The motion understanding system maintains the consistency of the knowledge through all the levels which supports the robot autonomy while accepting the human intervention. The superposing execution of the teleoperational task at multi-levels realizes intuitive and robust task execution for wide variety of objects and in changeful environment. The performance of several examples of operating chemical apparatuses is shown.

The NASA Langley Research Center 0.3-meter transonic cryogenic tunnel T-P/Re-M controller manual

NASA Technical Reports Server (NTRS)

Balakrishna, S.; Kilgore, W. Allen

1989-01-01

A new microcomputer based controller for the 0.3-m Transonic Cryogenic Tunnel (TCT) has been commissioned in 1988 and has reliably operated for more than a year. The tunnel stagnation pressure, gas stagnation temperature, tunnel wall structural temperature and flow Mach number are precisely controlled by the new controller in a stable manner. The tunnel control hardware, software, and the flow chart to assist in calibration of the sensors, actuators, and the controller real time functions are described. The software installation details are also presented. The report serves as the maintenance and trouble shooting manual for the 0.3-m TCT controller.

Quality Control of Pharmaceuticals

PubMed Central

Levi, Leo; Walker, George C.; Pugsley, L. I.

1964-01-01

Quality control is an essential operation of the pharmaceutical industry. Drugs must be marketed as safe and therapeutically active formulations whose performance is consistent and predictable. New and better medicinal agents are being produced at an accelerated rate. At the same time more exacting and sophisticated analytical methods are being developed for their evaluation. Requirements governing the quality control of pharmaceuticals in accordance with the Canadian Food and Drugs Act are cited and discussed. PMID:14199105

Identification of the feedforward component in manual control with predictable target signals.

PubMed

Drop, Frank M; Pool, Daan M; Damveld, Herman J; van Paassen, Marinus M; Mulder, Max

2013-12-01

In the manual control of a dynamic system, the human controller (HC) often follows a visible and predictable reference path. Compared with a purely feedback control strategy, performance can be improved by making use of this knowledge of the reference. The operator could effectively introduce feedforward control in conjunction with a feedback path to compensate for errors, as hypothesized in literature. However, feedforward behavior has never been identified from experimental data, nor have the hypothesized models been validated. This paper investigates human control behavior in pursuit tracking of a predictable reference signal while being perturbed by a quasi-random multisine disturbance signal. An experiment was done in which the relative strength of the target and disturbance signals were systematically varied. The anticipated changes in control behavior were studied by means of an ARX model analysis and by fitting three parametric HC models: two different feedback models and a combined feedforward and feedback model. The ARX analysis shows that the experiment participants employed control action on both the error and the target signal. The control action on the target was similar to the inverse of the system dynamics. Model fits show that this behavior can be modeled best by the combined feedforward and feedback model.

A Novel Approach for Enhancement of Automobile Clutch Engagement Quality Using Mechatronics Based Automated Clutch System

NASA Astrophysics Data System (ADS)

Tripathi, K.

2013-01-01

In automated manual clutch (AMC) a mechatronic system controls clutch force trajectory through an actuator governed by a control system. The present study identifies relevant characteristics of this trajectory and their effects on driveline dynamics and engagement quality. A new type of force trajectory is identified which gives the good engagement quality. However this trajectory is not achievable through conventional clutch control mechanism. But in AMC a mechatronic system based on electro-hydraulic or electro-mechanical elements can make it feasible. A mechatronic system is presented in which a mechatronic add-on system can be used to implement the novel force trajectory, without the requirement of replacing the traditional diaphragm spring based clutch in a vehicle with manual transmission.

30 CFR 28.31 - Quality control plans; contents.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality control plans; contents. 28.31 Section... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.31 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the management of quality, including: (1...

PROCESS DESIGN MANUAL FOR SLUDGE TREATMENT AND DISPOSAL

EPA Science Inventory

The purpose of this manual is to provide the engineering community and related industry with a new source of information to be used in the planning, design, and operation of present and future wastewater pollution control facilities. This manual supplements this existing knowledg...

[Highly quality-controlled radiation therapy].

PubMed

Shirato, Hiroki

2005-04-01

Advanced radiation therapy for intracranial disease has focused on set-up accuracy for the past 15 years. However, quality control in the prescribed dose is actually as important as the tumor set-up in radiation therapy. Because of the complexity of the three-dimensional radiation treatment planning system in recent years, the highly quality-controlled prescription of the dose has now been reappraised as the mainstream to improve the treatment outcome of radiation therapy for intracranial disease. The Japanese Committee for Quality Control of Radiation Therapy has developed fundamental requirements such as a QC committee in each hospital, a medical physicist, dosimetrists (QC members), and an external audit.

Control by quality: proposition of a typology.

PubMed

Pujo, P; Pillet, M

The application of Quality tools and methods in industrial management has always had a fundamental impact on the control of production. It influences the behavior of the actors concerned, while introducing the necessary notions and formalizations, especially for production systems with little or no automation, which constitute a large part of the industrial activity. Several quality approaches are applied in the workshop and are implemented at the level of the control. In this paper, the authors present a typology of the various approaches that have successively influenced control, such as statistical process control, quality assurance, and continuous improvement. First the authors present a parallel between production control and quality organizational structure. They note the duality between control, which is aimed at increasing productivity, and quality, which aims to satisfy the needs of the customer. They also note the hierarchical organizational structure of these two systems of management with, at each level, the notion of a feedback loop. This notion is fundamental to any kind of decision making. The paper is organized around the operational, tactical, and strategic levels, by describing for each level the main methods and tools for control by quality. The overview of these tools and methods starts at the operational level, with the Statistical Process Control, the Taguchi technique, and the "six sigma" approach. On the tactical level, we find a quality system approach, with a documented description of the procedures introduced in the firm. The management system can refer here to Quality Assurance, Total Productive Maintenance, or Management by Total Quality. The formalization through procedures of the rules of decision governing the process control enhances the validity of these rules. This leads to the enhancement of their reliability and to their consolidation. All this counterbalances the human, intrinsically fluctuating, behavior of the control

Activated Sludge. Student Manual. Biological Treatment Process Control.

ERIC Educational Resources Information Center

Boe, Owen K.; Klopping, Paul H.

This student manual contains the textual material for a seven-lesson unit on activated sludge. Topic areas addressed in the lessons include: (1) activated sludge concepts and components (including aeration tanks, aeration systems, clarifiers, and sludge pumping systems); (2) activated sludge variations and modes; (3) biological nature of activated…

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality control. 74.6 Section 74.6 Mineral... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and... DUST SAMPLING DEVICES Approval Requirements for Coal Mine Dust Personal Sampler Unit § 74.6 Quality...

California Publicly-Owned Utilities (POUs) – LBNL ‘Beyond Widgets’ Project. Task: ambient lighting and occupancy-based plug load control. System Program Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, Alastair; Mathew, Paul A.; Regnier, Cynthia

This program manual contains detailed technical information for implementing an incentive program for task-ambient lighting and occupancy-based plug load control. This manual was developed by Lawrence Berkeley National Laboratory, in collaboration with the California Publicly-Owned Utilities (CA POUs) as a partner in the ‘Beyond Widgets’ program funded by the U.S. Department of Energy Building Technologies Office. The primary audience for this manual is the program staff of the various CA POUs. It may also be used by other utility incentive programs to help develop similar programs. It is anticipated that the content of this manual be utilized by the CAmore » POU staff for developing related documents such as the Technical Resource Manual and other filings pertaining to the rollout of an energy systems-based rebate incentive program.« less

QCScreen: a software tool for data quality control in LC-HRMS based metabolomics.

PubMed

Simader, Alexandra Maria; Kluger, Bernhard; Neumann, Nora Katharina Nicole; Bueschl, Christoph; Lemmens, Marc; Lirk, Gerald; Krska, Rudolf; Schuhmacher, Rainer

2015-10-24

Metabolomics experiments often comprise large numbers of biological samples resulting in huge amounts of data. This data needs to be inspected for plausibility before data evaluation to detect putative sources of error e.g. retention time or mass accuracy shifts. Especially in liquid chromatography-high resolution mass spectrometry (LC-HRMS) based metabolomics research, proper quality control checks (e.g. for precision, signal drifts or offsets) are crucial prerequisites to achieve reliable and comparable results within and across experimental measurement sequences. Software tools can support this process. The software tool QCScreen was developed to offer a quick and easy data quality check of LC-HRMS derived data. It allows a flexible investigation and comparison of basic quality-related parameters within user-defined target features and the possibility to automatically evaluate multiple sample types within or across different measurement sequences in a short time. It offers a user-friendly interface that allows an easy selection of processing steps and parameter settings. The generated results include a coloured overview plot of data quality across all analysed samples and targets and, in addition, detailed illustrations of the stability and precision of the chromatographic separation, the mass accuracy and the detector sensitivity. The use of QCScreen is demonstrated with experimental data from metabolomics experiments using selected standard compounds in pure solvent. The application of the software identified problematic features, samples and analytical parameters and suggested which data files or compounds required closer manual inspection. QCScreen is an open source software tool which provides a useful basis for assessing the suitability of LC-HRMS data prior to time consuming, detailed data processing and subsequent statistical analysis. It accepts the generic mzXML format and thus can be used with many different LC-HRMS platforms to process both multiple

Oxidation Ditches. Student Manual. Biological Treatment Process Control.

ERIC Educational Resources Information Center

Nelsen, David

The textual material for a two-lesson unit on oxidation ditches is presented in this student manual. Topics discussed in the first lesson (introduction, theory, and components) include: history of the oxidation ditch process; various designs of the oxidation ditch; multi-trench systems; carrousel system; advantages and disadvantages of the…

Aerobic Digestion. Student Manual. Biological Treatment Process Control.

ERIC Educational Resources Information Center

Klopping, Paul H.

This manual contains the textual material for a single-lesson unit on aerobic sludge digestion. Topic areas addressed include: (1) theory of aerobic digestion; (2) system components; (3) performance factors; (4) indicators of stable operation; and (5) operational problems and their solutions. A list of objectives, glossary of key terms, and…

Aerated Lagoons. Student Manual. Biological Treatment Process Control.

ERIC Educational Resources Information Center

Andersen, Lorri

This student manual contains the textual material for a unit which focuses on the structural and operationally unique features of aerated lagoons. Topic areas discussed include: (1) characteristics of completely mixed aerated lagoons; (2) facultative aerated lagoons; (3) aerated oxidation ponds; (4) effects of temperature on aerated lagoons; (5)…

76 FR 60848 - National Mammography Quality Assurance Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-30

.../phone line to learn about possible modifications before coming to the meeting. Agenda: On November 4... status of the Full Field Digital Mammography universal quality control manual. FDA intends to make...

[Quality control in herbal supplements].

PubMed

Oelker, Luisa

2005-01-01

Quality and safety of food and herbal supplements are the result of a whole of different elements as good manufacturing practice and process control. The process control must be active and able to individuate and correct all possible hazards. The main and most utilized instrument is the hazard analysis critical control point (HACCP) system the correct application of which can guarantee the safety of the product. Herbal supplements need, in addition to standard quality control, a set of checks to assure the harmlessness and safety of the plants used.

Distributed sensor architecture for intelligent control that supports quality of control and quality of service.

PubMed

Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

2015-02-25

This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems.

Distributed Sensor Architecture for Intelligent Control that Supports Quality of Control and Quality of Service

PubMed Central

Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

2015-01-01

This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems. PMID:25723145

Quality control education in the community college

NASA Technical Reports Server (NTRS)

Greene, J. Griffen; Wilson, Steve

1966-01-01

This paper describes the Quality Control Program at Daytona Beach Junior College, including course descriptions. The program in quality control required communication between the college and the American Society for Quality Control (ASQC). The college has machinery established for certification of the learning process, and the society has the source of teachers who are competent in the technical field and who are the employers of the educational products. The associate degree for quality control does not have a fixed program, which can serve all needs, any more than all engineering degrees have identical programs. The main ideas which would be common to all quality control programs are the concept of economic control of a repetitive process and the concept of developing individual potentialities into individuals who are needed and productive.

Multimodal manual therapy vs. pharmacological care for management of tension type headache: A meta-analysis of randomized trials.

PubMed

Mesa-Jiménez, Juan A; Lozano-López, Cristina; Angulo-Díaz-Parreño, Santiago; Rodríguez-Fernández, Ángel L; De-la-Hoz-Aizpurua, Jose L; Fernández-de-Las-Peñas, Cesar

2015-12-01

Manual therapies are generally requested by patients with tension type headache. To compare the efficacy of multimodal manual therapy vs. pharmacological care for the management of tension type headache pain by conducting a meta-analysis of randomized controlled trials. PubMed, MEDLINE, EMBASE, AMED, CINAHL, EBSCO, Cochrane Database of Systematic Reviews, Cochrane Collaboration Trials Register, PEDro and SCOPUS were searched from their inception until June 2014. All randomized controlled trials comparing any manual therapy vs. medication care for treating tension type headache adults were included. Data were extracted and methodological quality assessed independently by two reviewers. We pooled headache frequency as the main outcome and also intensity and duration. The weighted mean difference between manual therapy and pharmacological care was used to determine effect sizes. Five randomized controlled trials met our inclusion criteria and were included in the meta-analysis. Pooled analyses found that manual therapies were more effective than pharmacological care in reducing frequency (weighted mean difference -0.8036, 95% confidence interval -1.66 to -0.44; three trials), intensity (weighted mean difference -0.5974, 95% confidence interval -0.8875 to -0.3073; five trials) and duration (weighted mean difference -0.5558, 95% confidence interval -0.9124 to -0.1992; three trials) of the headache immediately after treatment. No differences were found at longer follow-up for headache intensity (weighted mean difference -0.3498, 95% confidence interval -1.106 to 0.407; three trials). Manual therapies were associated with moderate effectiveness at short term, but similar effectiveness at longer follow-up for reducing headache frequency, intensity and duration in tension type headache than pharmacological medical drug care. However, due to the heterogeneity of the interventions, these results should be considered with caution at this stage. © International Headache

Applicator Training Manual for: Seed Treatment Pest Control.

ERIC Educational Resources Information Center

TeKrony, Dennis M.

This manual gives general information on seed treatment and type of seeds which can be treated. Also discussed are the problems and pests commonly associated with seed diseases and the fungicides and insecticides used for seed treatment. Information is also given on seed treatment equipment such as dust treaters, slurry treaters, and direct…

Low-speed longitudinal orbiter qualities

NASA Technical Reports Server (NTRS)

Powers, B. G.

1985-01-01

The shuttle program took on the challenge of providing a manual landing capability for an operational vehicle returning from orbit. Some complex challenges were encountered in developing the longitudinal flying qualities required to land the orbiter manually in an operational environment. Approach and landing test flights indicated a tendency for pilot-induced oscillation near landing. Changes in the operational procedures reduced the difficulty of the landing task, and an adaptive stick filter was incorporated to reduce the severity of any pilot-induced oscillatory motions. Fixed-base, movingbase, and in-flight simulations were used for the evaluations, and in general, flight simulation was the only reliable means of assessing the low-speed longitudinal flying qualities problems. Overall, the orbiter control system and operational procedures have produced a good capability to routinely perform precise landings with a large, unpowered vehicle with a low lift-to-drag ratio.

The curation paradigm and application tool used for manual curation of the scientific literature at the Comparative Toxicogenomics Database

PubMed Central

Davis, Allan Peter; Wiegers, Thomas C.; Murphy, Cynthia G.; Mattingly, Carolyn J.

2011-01-01

The Comparative Toxicogenomics Database (CTD) is a public resource that promotes understanding about the effects of environmental chemicals on human health. CTD biocurators read the scientific literature and convert free-text information into a structured format using official nomenclature, integrating third party controlled vocabularies for chemicals, genes, diseases and organisms, and a novel controlled vocabulary for molecular interactions. Manual curation produces a robust, richly annotated dataset of highly accurate and detailed information. Currently, CTD describes over 349 000 molecular interactions between 6800 chemicals, 20 900 genes (for 330 organisms) and 4300 diseases that have been manually curated from over 25 400 peer-reviewed articles. This manually curated data are further integrated with other third party data (e.g. Gene Ontology, KEGG and Reactome annotations) to generate a wealth of toxicogenomic relationships. Here, we describe our approach to manual curation that uses a powerful and efficient paradigm involving mnemonic codes. This strategy allows biocurators to quickly capture detailed information from articles by generating simple statements using codes to represent the relationships between data types. The paradigm is versatile, expandable, and able to accommodate new data challenges that arise. We have incorporated this strategy into a web-based curation tool to further increase efficiency and productivity, implement quality control in real-time and accommodate biocurators working remotely. Database URL: http://ctd.mdibl.org PMID:21933848

Effectiveness of Plaque Control with Novel Pediatric Oral Hygiene Need Station (Modified Oral Irrigation Device) as Compared with Manual Brushing and Flossing: Randomized Controlled Pilot Trial

PubMed Central

Murthy, Prashanth Sadashiva; Shaik, Naseemoon; Deshmukh, Seema; Girish, M. S.

2018-01-01

Background: Establishing good hygiene habits are valuable for present and future oral health. Below 6 years, tooth brushing should be performed by parents, as increasing dexterity and cognition may permit supervised brushing until the child is capable of independent brushing. Aim and Objectives: The aim of the present study was to evaluate the effectiveness of modified oral irrigation device in children in terms of plaque control and to compare the effectiveness of plaque control with manual brushing with the modified oral irrigation device in children. Materials and Methods: A randomized clinical trial was performed on 12 subjects who were allocated to the two study groups. After obtaining the consent, the control group was instructed tooth brushing with regular pediatric commercially available toothbrush and the intervention group with modified oral irrigation device. Plaque scores in both groups were assessed pre- and post-brushing using modified navy plaque index. Results: The data were subjected to Descriptive statistics and Paired t-test using SPSS version 22. Intragroup comparison of mean difference of plaque score in control group and intervention group pre- and post-brushing was statistically significant. Intergroup comparison of manual brushing group with modified oral irrigation group shows P < 0.05 was statistically significant. Conclusion: Within the limitation of the present study, it has been found novel pediatric oral hygiene need Station is more effective than manual brushing since it combined the effect of brushing, flossing (water floss), and rinsing in children simultaneously and at the same time did not demand any special motor skill. PMID:29875555

The Diabetes Manual trial protocol - a cluster randomized controlled trial of a self-management intervention for type 2 diabetes [ISRCTN06315411].

PubMed

Sturt, Jackie; Hearnshaw, Hilary; Farmer, Andrew; Dale, Jeremy; Eldridge, Sandra

2006-07-17

The Diabetes Manual is a type 2 diabetes self-management programme based upon the clinically effective 'Heart Manual'. The 12 week programme is a complex intervention theoretically underpinned by self-efficacy theory. It is a one to one intervention meeting United Kingdom requirements for structured diabetes-education and is delivered within routine primary care. In a two-group cluster randomized controlled trial, GP practices are allocated by computer minimisation to an intervention group or a six-month deferred intervention group. We aim to recruit 250 participants from 50 practices across central England. Eligibility criteria are adults able to undertake the programme with type 2 diabetes, not taking insulin, with HbA1c over 8% (first 12 months) and following an agreed protocol change over 7% (months 13 to 18). Following randomisation, intervention nurses receive two-day training and delivered the Diabetes Manual programme to participants. Deferred intervention nurses receive the training following six-month follow-up. Primary outcome is HbA1c with total and HDL cholesterol; blood pressure, body mass index; self-efficacy and quality of life as additional outcomes. Primary analysis is between-group HbA1c differences at 6 months powered to give 80% power to detect a difference in HbA1c of 0.6%. A 12 month cohort analysis will assess maintenance of effect and assess relationship between self-efficacy and outcomes, and a qualitative study is running alongside. This trial incorporates educational and psychological diabetes interventions into a single programme and assesses both clinical and psychosocial outcomes. The trial will increase our understanding of intervention transferability between conditions, those diabetes related health behaviours that are more or less susceptible to change through efficacy enhancing mechanisms and how this impacts on clinical outcomes.

Trial Protocol: Cognitive functional therapy compared with combined manual therapy and motor control exercise for people with non-specific chronic low back pain: protocol for a randomised, controlled trial.

PubMed

Belache, Fabiana Terra Cunha; Souza, Cíntia Pereira de; Fernandez, Jessica; Castro, Julia; Ferreira, Paula Dos Santos; Rosa, Elizana Rodrigues de Sousa; Araújo, Nathalia Cristina Gimenez de; Reis, Felipe José Jandre; Almeida, Renato Santos de; Nogueira, Leandro Alberto Calazans; Correia, Luís Cláudio Lemos; Meziat-Filho, Ney

2018-06-11

works with cognitive functional therapy, which increases the relevance of this study. The combined manual therapy and exercise group comprises an intervention strategy widely used by physiotherapists to treat low back pain. As evidence of efficacy is still limited, the results of a randomised, controlled clinical trial of high methodological quality will help physiotherapists in clinical decision-making. Copyright © 2018 Australian Physiotherapy Association. Published by Elsevier B.V. All rights reserved.

23 CFR 1340.8 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-04-01

... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data collection...) Statistical review. Survey results shall be reviewed and approved by a survey statistician, i.e., a person...

23 CFR 1340.8 - Quality control.

Code of Federal Regulations, 2014 CFR

2014-04-01

... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data collection...) Statistical review. Survey results shall be reviewed and approved by a survey statistician, i.e., a person...

23 CFR 1340.8 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-04-01

... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data collection...) Statistical review. Survey results shall be reviewed and approved by a survey statistician, i.e., a person...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

Instrument Quality Control.

PubMed

Jayakody, Chatura; Hull-Ryde, Emily A

2016-01-01

Well-defined quality control (QC) processes are used to determine whether a certain procedure or action conforms to a widely accepted standard and/or set of guidelines, and are important components of any laboratory quality assurance program (Popa-Burke et al., J Biomol Screen 14: 1017-1030, 2009). In this chapter, we describe QC procedures useful for monitoring the accuracy and precision of laboratory instrumentation, most notably automated liquid dispensers. Two techniques, gravimetric QC and photometric QC, are highlighted in this chapter. When used together, these simple techniques provide a robust process for evaluating liquid handler accuracy and precision, and critically underpin high-quality research programs.

Design, implementation, and quality control in the Pathways American-Indian multicenter trial

PubMed Central

Stone, Elaine J.; Norman, James E.; Davis, Sally M.; Stewart, Dawn; Clay, Theresa E.; Caballero, Ben; Lohman, Timothy G.; Murray, David M.

2016-01-01

Background Pathways was the first multicenter American-Indian school-based study to test the effectiveness of an obesity prevention program promoting healthy eating and physical activity. Methods Pathways employed a nested cohort design in which 41 schools were randomized to intervention or control conditions and students within these schools were followed as a cohort (1,704 third graders at baseline). The study’s primary endpoint was percent body fat. Secondary endpoints were levels of fat in school lunches; time spent in physical activity; and knowledge, attitudes, and behaviors regarding diet and exercise. Quality control (QC) included design of data management systems which provided standardization and quality assurance of data collection and processing. Data QC procedures at study centers included manuals of operation, training and certification, and monitoring of performance. Process evaluation was conducted to monitor dose and fidelity of the interventions. Registration and tracking systems were used for students and schools. Results No difference in mean percent body fat at fifth grade was found between the intervention and control schools. Percent of calories from fat and saturated fat in school lunches was significantly reduced in the intervention schools as was total energy intake from 24-hour recalls. Significant increases in self-reported physical activity levels and knowledge of healthy behaviors were found for the intervention school students. Conclusions The Pathways study results provide evidence demonstrating the role schools can play in public health promotion. Its study design and QC systems and procedures provide useful models for other similar school based multi- or single-site studies. PMID:14636805

14 CFR 145.211 - Quality control system.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Quality control system. 145.211 Section 145...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable to...

18 CFR 12.40 - Quality control programs.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Quality control... PROJECT WORKS Other Responsibilities of Applicant or Licensee § 12.40 Quality control programs. (a... meeting any requirements or standards set by the Regional Engineer. If a quality control program is...

18 CFR 12.40 - Quality control programs.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Quality control... PROJECT WORKS Other Responsibilities of Applicant or Licensee § 12.40 Quality control programs. (a... meeting any requirements or standards set by the Regional Engineer. If a quality control program is...

14 CFR 145.211 - Quality control system.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Quality control system. 145.211 Section 145...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable to...

Treatment manuals and the advancement of psychoanalytic knowledge: The Treatment Manual of the Tavistock Adult Depression Study.

PubMed

Taylor, David

2015-06-01

This paper has two aims: first, it seeks to understand the absence of treatment manuals in psychoanalysis. Secondly, it summarizes the treatment manual of the Tavistock Adult Depression Study, which describes the form of psychoanalytic psychotherapy whose effectiveness has been evaluated both in the Tavistock Adult Depression Study (TADS); and in the German Die Langzeittherapie bei chronischen Depressionen (LAC) Studie. Throughout the history of psychoanalysis, opinions about treatment manuals, empirical research and their antecedents have been deeply divided. After tracing the often polarized unfolding of these matters, the paper proposes that emotional and cognitive difficulties as well as scientific ones underpin their persistence. It is suggested that greater familiarity with them may lead to better combinations of outcome research and psychoanalysis: for example, the Tavistock manual seeks to match one account of the objects, aims, values, spirit and methods of psychoanalysis (as well as of connected forms of psychoanalytic psychotherapy); and also to meet what is required of treatment manuals by random allocation controlled trials. It has been a crucial element in the above studies of the outcome of long-term psychoanalytic psychotherapies with chronically depressed patients. After describing the Tavistock Manual, the paper concludes suggesting that, if appropriately constructed, treatment manuals can make a contribution to the advancement of specifically psychoanalytic knowledge. Copyright © 2015 Institute of Psychoanalysis.

Evaluation of Various Radar Data Quality Control Algorithms Based on Accumulated Radar Rainfall Statistics

NASA Technical Reports Server (NTRS)

Robinson, Michael; Steiner, Matthias; Wolff, David B.; Ferrier, Brad S.; Kessinger, Cathy; Einaudi, Franco (Technical Monitor)

2000-01-01

The primary function of the TRMM Ground Validation (GV) Program is to create GV rainfall products that provide basic validation of satellite-derived precipitation measurements for select primary sites. A fundamental and extremely important step in creating high-quality GV products is radar data quality control. Quality control (QC) processing of TRMM GV radar data is based on some automated procedures, but the current QC algorithm is not fully operational and requires significant human interaction to assure satisfactory results. Moreover, the TRMM GV QC algorithm, even with continuous manual tuning, still can not completely remove all types of spurious echoes. In an attempt to improve the current operational radar data QC procedures of the TRMM GV effort, an intercomparison of several QC algorithms has been conducted. This presentation will demonstrate how various radar data QC algorithms affect accumulated radar rainfall products. In all, six different QC algorithms will be applied to two months of WSR-88D radar data from Melbourne, Florida. Daily, five-day, and monthly accumulated radar rainfall maps will be produced for each quality-controlled data set. The QC algorithms will be evaluated and compared based on their ability to remove spurious echoes without removing significant precipitation. Strengths and weaknesses of each algorithm will be assessed based on, their abilit to mitigate both erroneous additions and reductions in rainfall accumulation from spurious echo contamination and true precipitation removal, respectively. Contamination from individual spurious echo categories will be quantified to further diagnose the abilities of each radar QC algorithm. Finally, a cost-benefit analysis will be conducted to determine if a more automated QC algorithm is a viable alternative to the current, labor-intensive QC algorithm employed by TRMM GV.

Massage, reflexology and other manual methods for pain management in labour.

PubMed

Smith, Caroline A; Levett, Kate M; Collins, Carmel T; Jones, Leanne

2012-02-15

Many women would like to avoid pharmacological or invasive methods of pain management in labour, and this may contribute towards the popularity of complementary methods of pain management. This review examined currently available evidence supporting the use of manual healing methods including massage and reflexology for pain management in labour. To examine the effects of manual healing methods including massage and reflexology for pain management in labour on maternal and perinatal morbidity. We searched the Cochrane Pregnancy and Childbirth Group's Trials Register (30 June 2011), the Cochrane Central Register of Controlled Trials (CENTRAL) (The Cochrane Library 2011, Issue 2 of 4), MEDLINE (1966 to 30 June 2011), CINAHL (1980 to 30 June 2011), the Australian and New Zealand Clinical Trial Registry (30 June 2011), Chinese Clinical Trial Register (30 June 2011), Current Controlled Trials (30 June 2011), ClinicalTrials.gov, (30 June 2011) ISRCTN Register (30 June 2011), National Centre for Complementary and Alternative Medicine (NCCAM) (30 June 2011) and the WHO International Clinical Trials Registry Platform (30 June 2011). Randomised controlled trials comparing manual healing methods with standard care, no treatment, other non-pharmacological forms of pain management in labour or placebo. Two authors independently assessed trial quality and extracted data. We attempted to contact study authors for additional information. We included six trials, with data reporting on five trials and 326 women in the meta-analysis. We found trials for massage only. Less pain during labour was reported from massage compared with usual care during the first stage of labour (standardised mean difference (SMD) -0.82, 95% confidence interval (CI) -1.17 to -0.47), four trials, 225 women), and labour pain was reduced in one trial of massage compared with music (risk ratio (RR) 0.40, 95% CI 0.18 to 0.89, 101 women). One trial of massage compared with usual care found reduced anxiety during

Editorial input for the right price: tobacco industry support for a sheet metal indoor air quality manual.

PubMed

Campbell, Richard; Balbach, Edith

2013-01-01

Following legal action in the 1990s, internal tobacco industry documents became public, allowing unprecedented insight into the industry's relationships with outside organizations. During the 1980s and 1990s, the National Energy Management Institute (NEMI), established by the Sheet Metal Workers International Association and the Sheet Metal and Air Conditioning Contractors' National Association, (SMACNA) received tobacco industry funding to establish an indoor air quality services program. But the arrangement also required NEMI to serve as an advocate for industry efforts to defeat indoor smoking bans by arguing that ventilation was a more appropriate solution to environmental tobacco smoke. Drawing on tobacco industry documents, this paper describes a striking example of the ethical compromises that accompanied NEMI's collaboration with the tobacco industry, highlighting the solicitation of tobacco industry financial support for a SMACNA indoor air quality manual in exchange for sanitizing references to the health impact of environmental tobacco smoke prior to publication.

Biological Concepts. Student Manual. Biological Treatment Process Control.

ERIC Educational Resources Information Center

Carnegie, John W.

This manual contains the textual material for a three-lesson unit which introduces students to the basic concepts applicable to all biological treatment systems. The general topic areas addressed in the lessons are: (1) the microorganisms found in biological systems; (2) the factors that affect the growth and health of biological systems; and (3)…

Demonstration and Research Pest Control: A Training Program for the Certification of Pesticide Applicators, Manual No. 10.

ERIC Educational Resources Information Center

Rust, Harry K.; And Others

This manual is intended to provide the information necessary to meet EPA standards for demonstration and research pest control and prepare for the written examination required for certification. Emphasis is placed on the principles of safe pesticide use. Chapters are included on pesticide applicator certification in Virginia, basics of pest…

Orofacial manual therapy improves cervical movement impairment associated with headache and features of temporomandibular dysfunction: a randomized controlled trial.

PubMed

von Piekartz, Harry; Hall, Toby

2013-08-01

There is evidence that temporomandibular disorder (TMD) may be a contributing factor to cervicogenic headache (CGH), in part because of the influence of dysfunction of the temporomandibular joint on the cervical spine. The purpose of this randomized controlled trial was to determine whether orofacial treatment in addition to cervical manual therapy, was more effective than cervical manual therapy alone on measures of cervical movement impairment in patients with features of CGH and signs of TMD. In this study, 43 patients (27 women) with headache for more than 3-months and with some features of CGH and signs of TMD were randomly assigned to receive either cervical manual therapy (usual care) or orofacial manual therapy to address TMD in addition to usual care. Subjects were assessed at baseline, after 6 treatment sessions (3-months), and at 6-months follow-up. 38 subjects (25 female) completed all analysis at 6-months follow-up. The outcome criteria were: cervical range of movement (including the C1-2 flexion-rotation test) and manual examination of the upper 3 cervical vertebra. The group that received orofacial treatment in addition to usual care showed significant reduction in all aspects of cervical impairment after the treatment period. These improvements persisted to the 6-month follow-up, but were not observed in the usual care group at any point. These observations together with previous reports indicate that manual therapists should look for features of TMD when examining patients with headache, particularly if treatment fails when directed to the cervical spine. Copyright © 2013. Published by Elsevier Ltd.

METRO-APEX Volume 17.1: Industrialist's Manual No. 7, Shick Cannery. Revised.

ERIC Educational Resources Information Center

University of Southern California, Los Angeles. COMEX Research Project.

The Industrialist's Manual No. 7 (Shick Cannery) is one of a set of twenty-one manuals used in METRO-APEX 1974, a computerized college and professional level, computer-supported, role-play, simulation exercise of a community with "normal" problems. Stress is placed on environmental quality considerations. APEX 1974 is an expansion of…

Quality Control in construction.

DTIC Science & Technology

1984-01-01

behavioral scientists. In 1962, Dr. Kaoru Ishikawa gave shape to the form of training which featured intradepartmental groups of ten or so workers seated...and Japanese circles bears closer scrutiny. 4.3.1 Japanese Ingredients of Quality The founder of quality circles, Dr. Kaoru Ishikawa , gives six...around 51 a table; hence the name Quality Control Circle. 4 Dr. 0 Ishikawa was an engineering professor at Tokyo University, and the circles were

Sensor fault-tolerant control for gear-shifting engaging process of automated manual transmission

NASA Astrophysics Data System (ADS)

Li, Liang; He, Kai; Wang, Xiangyu; Liu, Yahui

2018-01-01

Angular displacement sensor on the actuator of automated manual transmission (AMT) is sensitive to fault, and the sensor fault will disturb its normal control, which affects the entire gear-shifting process of AMT and results in awful riding comfort. In order to solve this problem, this paper proposes a method of fault-tolerant control for AMT gear-shifting engaging process. By using the measured current of actuator motor and angular displacement of actuator, the gear-shifting engaging load torque table is built and updated before the occurrence of the sensor fault. Meanwhile, residual between estimated and measured angular displacements is used to detect the sensor fault. Once the residual exceeds a determined fault threshold, the sensor fault is detected. Then, switch control is triggered, and the current observer and load torque table estimates an actual gear-shifting position to replace the measured one to continue controlling the gear-shifting process. Numerical and experiment tests are carried out to evaluate the reliability and feasibility of proposed methods, and the results show that the performance of estimation and control is satisfactory.

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quality control. 74.6 Section 74.6 Mineral... control. The applicant shall describe the way in which each lot of components will be sampled and tested... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and...

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality control. 74.6 Section 74.6 Mineral... control. The applicant shall describe the way in which each lot of components will be sampled and tested... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and...

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quality control. 74.6 Section 74.6 Mineral... control. The applicant shall describe the way in which each lot of components will be sampled and tested... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and...

New techniques for the analysis of manual control systems. [mathematical models of human operator behavior

NASA Technical Reports Server (NTRS)

Bekey, G. A.

1971-01-01

Studies are summarized on the application of advanced analytical and computational methods to the development of mathematical models of human controllers in multiaxis manual control systems. Specific accomplishments include the following: (1) The development of analytical and computer methods for the measurement of random parameters in linear models of human operators. (2) Discrete models of human operator behavior in a multiple display situation were developed. (3) Sensitivity techniques were developed which make possible the identification of unknown sampling intervals in linear systems. (4) The adaptive behavior of human operators following particular classes of vehicle failures was studied and a model structure proposed.

Effects of manual therapy on treatment duration and motor development in infants with severe nonsynostotic plagiocephaly: a randomised controlled pilot study.

PubMed

Cabrera-Martos, I; Valenza, M C; Valenza-Demet, G; Benítez-Feliponi, A; Robles-Vizcaíno, C; Ruiz-Extremera, A

2016-11-01

Despite growing evidence regarding nonsynostotic plagiocephaly and their repercussions on motor development, there is little evidence to support the use of manual therapy as an adjuvant option. The aim of this study was to evaluate the effects of a therapeutic approach based on manual therapy as an adjuvant option on treatment duration and motor development in infants with severe nonsynostotic plagiocephaly. This is a randomised controlled pilot study. The study was conducted at a university hospital. Forty-six infants with severe nonsynostotic plagiocephaly (types 4-5 of the Argenta scale) referred to the Early Care and Monitoring Unit were randomly allocated to a control group receiving standard treatment (repositioning and an orthotic helmet) or to an experimental group treated with manual therapy added to standard treatment. Infants were discharged when the correction of the asymmetry was optimal taken into account the previous clinical characteristics. The outcome measures were treatment duration and motor development assessed with the Alberta Infant Motor Scale (AIMS) at baseline and at discharge. Asymmetry after the treatment was minimal (type 0 or 1 according to the Argenta scale) in both groups. A comparative analysis showed that treatment duration was significantly shorter (p < 0.001) in the experimental group (109.84 ± 14.45 days) compared to the control group (148.65 ± 11.53 days). The motor behaviour was normal (scores above the 16th percentile of the AIMS) in all the infants after the treatment. Manual therapy added to standard treatment reduces the treatment duration in infants with severe nonsynostotic plagiocephaly.

Applicator Training Manual for: Agriculture Plant Pest Control.

ERIC Educational Resources Information Center

Witt, William W.; And Others

This manual gives information on insects that damage crops. These fall in two categories: (1) insects with a complete life cycle such as butterflies and moths, boring insects, and beetles; and (2) those with a gradual life cycle. Also included are descriptions of leaf diseases, wilts and root and crown rots, stem cankers, fruit rots, seed and…

Quality Assurance and Quality Control, Part 2.

PubMed

Akers, Michael J

2015-01-01

The tragedy surrounding the New England Compounding Center and contaminated steroid syringe preparations clearly points out what can happen if quality-assurance and quality-control procedures are not strictly practiced in the compounding of sterile preparations. This article is part 2 of a two-part article on requirements to comply with United States Pharmacopeia general chapters <797> and <1163> with respect to quality assurance of compounded sterile preparations. Part 1 covered documentation requirements, inspection procedures, compounding accuracy checks, and part of a discussion on bacterial endotoxin testing. Part 2 covers sterility testing, the completion from part 1 on bacterial endotoxin testing, a brief dicussion of United States Pharmacopeia <1163>, and advances in pharmaceutical quality systems.

Automatic initialization and quality control of large-scale cardiac MRI segmentations.

PubMed

Albà, Xènia; Lekadir, Karim; Pereañez, Marco; Medrano-Gracia, Pau; Young, Alistair A; Frangi, Alejandro F

2018-01-01

Continuous advances in imaging technologies enable ever more comprehensive phenotyping of human anatomy and physiology. Concomitant reduction of imaging costs has resulted in widespread use of imaging in large clinical trials and population imaging studies. Magnetic Resonance Imaging (MRI), in particular, offers one-stop-shop multidimensional biomarkers of cardiovascular physiology and pathology. A wide range of analysis methods offer sophisticated cardiac image assessment and quantification for clinical and research studies. However, most methods have only been evaluated on relatively small databases often not accessible for open and fair benchmarking. Consequently, published performance indices are not directly comparable across studies and their translation and scalability to large clinical trials or population imaging cohorts is uncertain. Most existing techniques still rely on considerable manual intervention for the initialization and quality control of the segmentation process, becoming prohibitive when dealing with thousands of images. The contributions of this paper are three-fold. First, we propose a fully automatic method for initializing cardiac MRI segmentation, by using image features and random forests regression to predict an initial position of the heart and key anatomical landmarks in an MRI volume. In processing a full imaging database, the technique predicts the optimal corrective displacements and positions in relation to the initial rough intersections of the long and short axis images. Second, we introduce for the first time a quality control measure capable of identifying incorrect cardiac segmentations with no visual assessment. The method uses statistical, pattern and fractal descriptors in a random forest classifier to detect failures to be corrected or removed from subsequent statistical analysis. Finally, we validate these new techniques within a full pipeline for cardiac segmentation applicable to large-scale cardiac MRI databases. The

Guidance for Efficient Small Animal Imaging Quality Control.

PubMed

Osborne, Dustin R; Kuntner, Claudia; Berr, Stuart; Stout, David

2017-08-01

Routine quality control is a critical aspect of properly maintaining high-performance small animal imaging instrumentation. A robust quality control program helps produce more reliable data both for academic purposes and as proof of system performance for contract imaging work. For preclinical imaging laboratories, the combination of costs and available resources often limits their ability to produce efficient and effective quality control programs. This work presents a series of simplified quality control procedures that are accessible to a wide range of preclinical imaging laboratories. Our intent is to provide minimum guidelines for routine quality control that can assist preclinical imaging specialists in setting up an appropriate quality control program for their facility.