Quality controls for wind measurement of a 1290-MHz boundary layer profiler under strong wind conditions.

PubMed

Liu, Zhao; Zheng, Chaorong; Wu, Yue

2017-09-01

Wind profilers have been widely adopted to observe the wind field information in the atmosphere for different purposes. But accuracy of its observation has limitations due to various noises or disturbances and hence need to be further improved. In this paper, the data measured under strong wind conditions, using a 1290-MHz boundary layer profiler (BLP), are quality controlled via a composite quality control (QC) procedure proposed by the authors. Then, through the comparison with the data measured by radiosonde flights (balloon observations), the critical thresholds in the composite QC procedure, including consensus average threshold T 1 and vertical shear threshold T 3 , are systematically discussed. And the performance of the BLP operated under precipitation is also evaluated. It is found that to ensure the high accuracy and high data collectable rate, the optimal range of subsets is determined to be 4 m/s. Although the number of data rejected by the combined algorithm of vertical shear examination and small median test is quite limited, it is proved that the algorithm is quite useful to recognize the outlier with a large discrepancy. And the optimal wind shear threshold T 3 can be recommended as 5 ms -1 /100m. During patchy precipitation, the quality of data measured by the four oblique beams (using the DBS measuring technique) can still be ensured. After the BLP data are quality controlled by the composite QC procedure, the output can show good agreement with the balloon observation.

Use of near-infrared spectroscopy and multipoint measurements for quality control of pharmaceutical drug products.

PubMed

Boiret, Mathieu; Chauchard, Fabien

2017-01-01

Near-infrared (NIR) spectroscopy is a non-destructive analytical technique that enables better-understanding and optimization of pharmaceutical processes and final drug products. The use in line is often limited by acquisition speed and sampling area. This work focuses on performing a multipoint measurement at high acquisition speed at the end of the manufacturing process on a conveyor belt system to control both the distribution and the content of active pharmaceutical ingredient within final drug products, i.e., tablets. A specially designed probe with several collection fibers was developed for this study. By measuring spectral and spatial information, it provides physical and chemical knowledge on the final drug product. The NIR probe was installed on a conveyor belt system that enables the analysis of a lot of tablets. The use of these NIR multipoint measurement probes on a conveyor belt system provided an innovative method that has the potential to be used as a new paradigm to ensure the drug product quality at the end of the manufacturing process and as a new analytical method for the real-time release control strategy. Graphical abstract Use of near-infrared spectroscopy and multipoint measurements for quality control of pharmaceutical drug products.

Quality improvement in coronary care: analysis of sustainability and impact on adjacent clinical measures after a Swedish controlled, multicenter quality improvement collaborative.

PubMed

Carlhed, Rickard; Bellman, Christina; Bojestig, Mats; Bojö, Leif; Peterson, Anette; Lindahl, Bertil

2012-08-01

Quality Improvement in Coronary Care, a Swedish multicenter, controlled quality-improvement (QI) collaborative, has shown significant improvements in adherence to national guidelines for acute myocardial infarction, as well as improved clinical outcome. The objectives of this report were to describe the sustainability of the improvements after withdrawal of study support and a consolidation period of 3 months and to report whether improvements were disseminated to treatments and diagnostic procedures other than those primarily targeted. Multidisciplinary teams from 19 Swedish hospitals were educated in basic QI methodologies. Another 19 matched hospitals were included as blinded controls. All evaluations were made on the hospital level, and data were obtained from a national quality registry, Swedish Register of Information and Knowledge About Swedish Heart Intensive Care Admissions (RIKS-HIA). Sustainability indicators consisted of use of angiotensin-converting enzyme inhibitors, lipid-lowering therapy, clopidogrel, low-molecular weight heparin, and coronary angiography. Dissemination indicators were use of echocardiography, stress tests, and reperfusion therapy; time delays; and length of stay. At the reevaluation period of 6 months, the improvements at the QI intervention hospitals were sustained in all indicators but 1 (angiotensin-converting enzyme inhibitor). Between the 2 measurements, the control group improved significantly in all but 1 indicator (angiotensin-converting enzyme inhibitor). However, at the second measurement, the absolute adherence rates of the intervention hospitals were still numerically higher in all 5 indicators, and significantly so in 1 (clopidogrel). No significant changes were observed for the dissemination indicators. The combination of a systematic QI collaborative with a national, interactive quality registry might lead to substantial and sustained improvements in the quality of acute myocardial infarction care. However, to

Quality control in gastrointestinal surgery.

PubMed

Ramírez-Barba, Ector Jaime; Arenas-Moya, Diego; Vázquez-Guerrero, Arturo

2011-01-01

We analyzed the Mexican legal framework, identifying the vectors that characterize quality and control in gastrointestinal surgery. Quality is contemplated in the health protection rights determined according to the Mexican Constitution, established in the general health law and included as a specific goal in the actual National Development Plan and Health Sector Plan. Quality control implies planning, verification and application of corrective measures. Mexico has implemented several quality strategies such as certification of hospitals and regulatory agreements by the General Salubrity Council, creation of the National Health Quality Committee, generation of Clinical Practice Guidelines and the Certification of Medical Specialties, among others. Quality control in gastrointestinal surgery must begin at the time of medical education and continue during professional activities of surgeons, encouraging multidisciplinary teamwork, knowledge, abilities, attitudes, values and skills that promote homogeneous, safe and quality health services for the Mexican population.

Distributed sensor architecture for intelligent control that supports quality of control and quality of service.

PubMed

Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

2015-02-25

This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems.

Distributed Sensor Architecture for Intelligent Control that Supports Quality of Control and Quality of Service

PubMed Central

Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

2015-01-01

This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems. PMID:25723145

Measuring health care process quality with software quality measures.

PubMed

Yildiz, Ozkan; Demirörs, Onur

2012-01-01

Existing quality models focus on some specific diseases, clinics or clinical areas. Although they contain structure, process, or output type measures, there is no model which measures quality of health care processes comprehensively. In addition, due to the not measured overall process quality, hospitals cannot compare quality of processes internally and externally. To bring a solution to above problems, a new model is developed from software quality measures. We have adopted the ISO/IEC 9126 software quality standard for health care processes. Then, JCIAS (Joint Commission International Accreditation Standards for Hospitals) measurable elements were added to model scope for unifying functional requirements. Assessment (diagnosing) process measurement results are provided in this paper. After the application, it was concluded that the model determines weak and strong aspects of the processes, gives a more detailed picture for the process quality, and provides quantifiable information to hospitals to compare their processes with multiple organizations.

Use of NEXRAD radar-based observations for quality control of in-situ rain gauge measurements

NASA Astrophysics Data System (ADS)

Nelson, B. R.; Prat, O.; Leeper, R.

2017-12-01

Rain gauge quality control is an often over looked important step in the archive of historical precipitation estimates. We investigate the possibilities that exist for using ground based radar networks for quality control of rain gauge measurements. This process includes the point to pixel comparisons of the rain gauge measurements with NEXRAD observations. There are two NEXRAD based data sets used for reference; the NCEP stage IV and the NWS MRMS gridded data sets. The NCEP stage IV data set is available at 4km hourly for the period 2002-present and includes the radar-gauge bias adjusted precipitation estimate. The NWS MRMS data set includes several different variables such as reflectivity, radar-only estimates, precipitation flag, and radar-gauge bias adjusted precipitation estimates. The latter product provides for much more information to apply quality control such as identification of precipitation type, identification of storm type and Z-R relation. In addition, some of the variables are available at 5-minute scale. The rain gauge networks that are investigated are the Climate Reference Network (CRN), the Fischer-Porter Hourly Precipitation Database (HPD), and the Hydrometeorological Automated Data System (HADS). The CRN network is available at the 5-minute scale, the HPD network is available at the 15-minute and hourly scale, and HADS is available at the hourly scale. The varying scales present challenges for comparisons. However given the higher resolution radar-based products we identify an optimal combination of rain gauge observations that can be compared to the radar-based information. The quality control process focuses on identifying faulty gauges in direct comparison while a deeper investigation focuses on event-based differences from light rain to extreme storms.

The measurement of carbon monoxide and methane in the National Capital Air Quality Control Region. I - Measurement systems

NASA Technical Reports Server (NTRS)

Lebel, P. J.; Lamontagne, R. A.; Goldstein, H. W.

1976-01-01

The Carbon Monoxide Pollution Experiment (COPE) and the National Capital Air Quality Control Region (NCAQCR) undertook a series of measurements of atmospheric CO and CH4 to determine the accuracy of the airborne COPE Correlation Interfer4meter. The device, a modified Michelson interferometer, measures the atmospheric column density of CO and CH4 at 2.3 microns with tropospheric measurement sensitivities of 70 and 10 PPB, respectively. Data for evaluating the remote measurements included atmospheric column density measurements at a ground truth site using a van-mounted infrared Fourier spectrometer; continuous ground level gas chromatographic measurements; and chromatographic data from atmospheric grab samples collected by aircraft and at ground locations. The instruments and sampling techniques used in the experiment are described in detail.

Measurement control workshop instructional materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gibbs, Philip; Harvel, Charles; Clark, John

2012-09-01

An essential element in an effective nuclear materials control and accountability (MC&A) program is the measurement of the nuclear material as it is received, moved, processed and shipped. Quality measurement systems and methodologies determine the accuracy of the accountability values. Implementation of a measurement control program is essential to ensure that the measurement systems and methodologies perform as expected. A measurement control program also allows for a determination of the level of confidence in the accounting values.

On quality control procedures for solar radiation and meteorological measures, from subhourly to montly average time periods

NASA Astrophysics Data System (ADS)

Espinar, B.; Blanc, P.; Wald, L.; Hoyer-Klick, C.; Schroedter-Homscheidt, M.; Wanderer, T.

2012-04-01

Meteorological data measured by ground stations are often a key element in the development and validation of methods exploiting satellite images. These data are considered as a reference against which satellite-derived estimates are compared. Long-term radiation and meteorological measurements are available from a large number of measuring stations. However, close examination of the data often reveals a lack of quality, often for extended periods of time. This lack of quality has been the reason, in many cases, of the rejection of large amount of available data. The quality data must be checked before their use in order to guarantee the inputs for the methods used in modelling, monitoring, forecast, etc. To control their quality, data should be submitted to several conditions or tests. After this checking, data that are not flagged by any of the test is released as a plausible data. In this work, it has been performed a bibliographical research of quality control tests for the common meteorological variables (ambient temperature, relative humidity and wind speed) and for the usual solar radiometrical variables (horizontal global and diffuse components of the solar radiation and the beam normal component). The different tests have been grouped according to the variable and the average time period (sub-hourly, hourly, daily and monthly averages). The quality test may be classified as follows: • Range checks: test that verify values are within a specific range. There are two types of range checks, those based on extrema and those based on rare observations. • Step check: test aimed at detecting unrealistic jumps or stagnation in the time series. • Consistency checks: test that verify the relationship between two or more time series. The gathered quality tests are applicable for all latitudes as they have not been optimized regionally nor seasonably with the aim of being generic. They have been applied to ground measurements in several geographic locations, what

Comparative evaluation of two asthma care quality measures among Medicaid beneficiaries.

PubMed

Samnaliev, Mihail; Baxter, Jeffrey D; Clark, Robin E

2009-05-01

The relative performance of asthma care quality measures has not been evaluated in Medicaid populations. Using complete claims and pharmaceutical data for 19,076 patients with persistent asthma (based on Health Effectiveness and Data Information Set criteria) in five Medicaid populations, we compared the following two measures of asthma care quality: filling prescriptions for controller asthma medications within 1 year and the ratio of controller medication to the total number of asthma medication prescriptions filled within 1 year. We calculated whether meeting each quality measure was associated with decreased odds of emergency department (ED) treatment episodes. We then compared the odds ratios, receiver operating characteristic (ROC) curves, and deviances between models, using each measure to predict ED utilization in Medicaid populations. Although meeting each measure was associated with lower odds of ED utilization, this decrease was larger if the controller asthma medication measure was met rather than the ratio measure. Additionally, models using the controller medication measure had greater areas under the ROC curve and smaller deviances than models using the ratio measure. Both administrative measures of asthma care quality were associated with lower odds of ED utilization. The controller medication measure of asthma care quality may be better than the ratio measure in relation to emergency asthma care utilization by Medicaid beneficiaries.

Will the "Fixes" Fall Flat? Prospects for Quality Measures and Payment Incentives to Control Healthcare Spending.

PubMed

Hauswald, Erik; Sklar, David

2017-04-01

Payment systems in the US healthcare system have rewarded physicians for services and attempted to control healthcare spending, with rewards and penalties based upon projected goals for future spending. The incorporation of quality goals and alternatives to fee-for-service was introduced to replace the previous system of rewards and penalties. We describe the history of the US healthcare payment system, focusing on Medicare and the efforts to control spending through the Sustainable Growth Rate. We describe the latest evolution of the payment system, which emphasizes quality measurement and alternative payment models. We conclude with suggestions for how to influence physician behavior through education and payment reform so that their behavior aligns with alternative care models to control spending in the future.

Influence of staff infection control training on infection-related quality measures in US nursing homes.

PubMed

Kaur, Jasjit; Stone, Patricia W; Travers, Jasmine L; Cohen, Catherine C; Herzig, Carolyn T A

2017-09-01

Health care-associated infections are a leading cause of morbidity and mortality in US nursing home residents. Ongoing training of nursing home staff is vital to the implementation of infection prevention and control processes. Our aim was to describe associations between methods, frequency, and timing of staff infection prevention and control training and infection-related quality measures. In this national survey of nursing homes, timing of staff infection prevention and control training was associated with reduced indwelling urinary catheter use. Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Quality-control design for surface-water sampling in the National Water-Quality Network

USGS Publications Warehouse

Riskin, Melissa L.; Reutter, David C.; Martin, Jeffrey D.; Mueller, David K.

2018-04-10

The data-quality objectives for samples collected at surface-water sites in the National Water-Quality Network include estimating the extent to which contamination, matrix effects, and measurement variability affect interpretation of environmental conditions. Quality-control samples provide insight into how well the samples collected at surface-water sites represent the true environmental conditions. Quality-control samples used in this program include field blanks, replicates, and field matrix spikes. This report describes the design for collection of these quality-control samples and the data management needed to properly identify these samples in the U.S. Geological Survey’s national database.

Comparing clinical quality indicators for asthma management in children with outcome measures used in randomised controlled trials: a protocol.

PubMed

Choong, Miew Keen; Tsafnat, Guy; Hibbert, Peter; Runciman, William B; Coiera, Enrico

2015-09-08

Clinical quality indicators are necessary to monitor the performance of healthcare services. The development of indicators should, wherever possible, be based on research evidence to minimise the risk of bias which may be introduced during their development, because of logistic, ethical or financial constraints alone. The development of automated methods to identify the evidence base for candidate indicators should improve the process of indicator development. The objective of this study is to explore the relationship between clinical quality indicators for asthma management in children with outcome and process measurements extracted from randomised controlled clinical trial reports. National-level indicators for asthma management in children will be extracted from the National Quality Measures Clearinghouse (NQMC) database and the National Institute for Health and Care Excellence (NICE) quality standards. Outcome measures will be extracted from published English language randomised controlled trial (RCT) reports for asthma management in children aged below 12 years. The two sets of measures will be compared to assess any overlap. The study will provide insights into the relationship between clinical quality indicators and measurements in RCTs. This study will also yield a list of measurements used in RCTs for asthma management in children, and will find RCT evidence for indicators used in practice. Ethical approval is not necessary because this study will not include patient data. Findings will be disseminated through peer-reviewed publications. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Data-quality measures for stakeholder-implemented watershed-monitoring programs

USGS Publications Warehouse

Greve, Adrienne I.

2002-01-01

Community-based watershed groups, many of which collect environmental data, have steadily increased in number over the last decade. The data generated by these programs are often underutilized due to uncertainty in the quality of data produced. The incorporation of data-quality measures into stakeholder monitoring programs lends statistical validity to data. Data-quality measures are divided into three steps: quality assurance, quality control, and quality assessment. The quality-assurance step attempts to control sources of error that cannot be directly quantified. This step is part of the design phase of a monitoring program and includes clearly defined, quantifiable objectives, sampling sites that meet the objectives, standardized protocols for sample collection, and standardized laboratory methods. Quality control (QC) is the collection of samples to assess the magnitude of error in a data set due to sampling, processing, transport, and analysis. In order to design a QC sampling program, a series of issues needs to be considered: (1) potential sources of error, (2) the type of QC samples, (3) inference space, (4) the number of QC samples, and (5) the distribution of the QC samples. Quality assessment is the process of evaluating quality-assurance measures and analyzing the QC data in order to interpret the environmental data. Quality assessment has two parts: one that is conducted on an ongoing basis as the monitoring program is running, and one that is conducted during the analysis of environmental data. The discussion of the data-quality measures is followed by an example of their application to a monitoring program in the Big Thompson River watershed of northern Colorado.

Contributions of CCLM to advances in quality control.

PubMed

Kazmierczak, Steven C

2013-01-01

Abstract The discipline of laboratory medicine is relatively young when considered in the context of the history of medicine itself. The history of quality control, within the context of laboratory medicine, also enjoys a relatively brief, but rich history. Laboratory quality control continues to evolve along with advances in automation, measurement techniques and information technology. Clinical Chemistry and Laboratory Medicine (CCLM) has played a key role in helping disseminate information about the proper use and utility of quality control. Publication of important advances in quality control techniques and dissemination of guidelines concerned with laboratory quality control has undoubtedly helped readers of this journal keep up to date on the most recent developments in this field.

A precipitation database of station-based daily and monthly measurements for West Africa: Overview, quality control and harmonization

NASA Astrophysics Data System (ADS)

Bliefernicht, Jan; Waongo, Moussa; Annor, Thompson; Laux, Patrick; Lorenz, Manuel; Salack, Seyni; Kunstmann, Harald

2017-04-01

West Africa is a data sparse region. High quality and long-term precipitation data are often not readily available for applications in hydrology, agriculture, meteorology and other needs. To close this gap, we use multiple data sources to develop a precipitation database with long-term daily and monthly time series. This database was compiled from 16 archives including global databases e.g. from the Global Historical Climatology Network (GHCN), databases from research projects (e.g. the AMMA database) and databases of the national meteorological services of some West African countries. The collection consists of more than 2000 precipitation gauges with measurements dating from 1850 to 2015. Due to erroneous measurements (e.g. temporal offsets, unit conversion errors), missing values and inconsistent meta-data, the merging of this precipitation dataset is not straightforward and requires a thorough quality control and harmonization. To this end, we developed geostatistical-based algorithms for quality control of individual databases and harmonization to a joint database. The algorithms are based on a pairwise comparison of the correspondence of precipitation time series in dependence to the distance between stations. They were tested for precipitation time series from gages located in a rectangular domain covering Burkina Faso, Ghana, Benin and Togo. This harmonized and quality controlled precipitation database was recently used for several applications such as the validation of a high resolution regional climate model and the bias correction of precipitation projections provided the Coordinated Regional Climate Downscaling Experiment (CORDEX). In this presentation, we will give an overview of the novel daily and monthly precipitation database and the algorithms used for quality control and harmonization. We will also highlight the quality of global and regional archives (e.g. GHCN, GSOD, AMMA database) in comparison to the precipitation databases provided by the

Venous Thromboembolism Quality Measures Fail to Accurately Measure Quality.

PubMed

Lau, Brandyn D; Streiff, Michael B; Pronovost, Peter J; Haut, Elliott R

2018-03-20

Venous thromboembolism (VTE) is 1 of the most common causes of preventable harm for patients in hospitals. Consequently, the Joint Commission, the Centers for Medicare and Medicaid Services, the Agency for Healthcare Research and Quality, the United Kingdom Care Quality Commission, the Australian Commission on Safety and Quality in Health Care, the Maryland Health Services Cost Review Commission, and the American College of Surgeons have prioritized measuring and reporting VTE outcomes with the goal of reducing the incidence of and preventable harm from VTE. We developed a rubric for defect-free VTE prevention, graded each organizational VTE quality measure, and found that none of the current VTE-related quality measures adequately characterizes VTE prevention efforts or outcomes in hospitalized patients. Effective VTE prevention is multifactorial: clinicians must assess patients' risk for VTE and prescribe therapy appropriate for each patient's risk profile, patients must accept the prescribed therapy, and nurses must administer the therapy as prescribed. First, an ideal, defect-free VTE prevention process measure requires: (1) documentation of a standardized VTE risk assessment; (2) prescription of optimal, risk-appropriate VTE prophylaxis; and (3) administration of all risk-appropriate VTE prophylaxis as prescribed. Second, an ideal VTE outcome measure should define potentially preventable VTE as VTE that developed in patients who experienced any VTE prevention process failures. © 2018 American Heart Association, Inc.

CRN5EXP: Expert system for statistical quality control

NASA Technical Reports Server (NTRS)

Hentea, Mariana

1991-01-01

The purpose of the Expert System CRN5EXP is to assist in checking the quality of the coils at two very important mills: Hot Rolling and Cold Rolling in a steel plant. The system interprets the statistical quality control charts, diagnoses and predicts the quality of the steel. Measurements of process control variables are recorded in a database and sample statistics such as the mean and the range are computed and plotted on a control chart. The chart is analyzed through patterns using the C Language Integrated Production System (CLIPS) and a forward chaining technique to reach a conclusion about the causes of defects and to take management measures for the improvement of the quality control techniques. The Expert System combines the certainty factors associated with the process control variables to predict the quality of the steel. The paper presents the approach to extract data from the database, the reason to combine certainty factors, the architecture and the use of the Expert System. However, the interpretation of control charts patterns requires the human expert's knowledge and lends to Expert Systems rules.

The process of managerial control in quality improvement initiatives.

PubMed

Slovensky, D J; Fottler, M D

1994-11-01

The fundamental intent of strategic management is to position an organization with in its market to exploit organizational competencies and strengths to gain competitive advantage. Competitive advantage may be achieved through such strategies as low cost, high quality, or unique services or products. For health care organizations accredited by the Joint Commission on Accreditation of Healthcare Organizations, continually improving both processes and outcomes of organizational performance--quality improvement--in all operational areas of the organization is a mandated strategy. Defining and measuring quality and controlling the quality improvement strategy remain problematic. The article discusses the nature and processes of managerial control, some potential measures of quality, and related information needs.

Quantitative ultrasound measurements of bone quality in female adolescents with idiopathic scoliosis compared to normal controls.

PubMed

Du, Qing; Zhou, Xuan; Li, Jian A; He, Xiao H; Liang, Ju P; Zhao, Li; Yang, Xiao Y; Chen, Nan; Zhang, Shu X; Chen, Pei J

2015-01-01

The aims of this study were to compare the speed-of-sound (SOS) between adolescent idiopathic scoliosis (AIS) patients and controls using quantitative ultrasound examination and to further analyze the relationship between the SOS and curve type, curve magnitude, maturation status and Risser's sign in AIS patients compared to controls. Seventy-eight female AIS patients and 58 healthy female controls 10 to 16 years of age were recruited to participate. Quantitative ultrasound measurements were performed at the non-dominant distal end of the radius. The standard method for estimating the SOS and z-score was used. Comparisons were made between the SOS values and z-score in AIS patients and age-matched Asian adolescents. The SOS values of the patients were significantly lower than the controls (P < .01). The percentage of cases with low bone quality was 25% in the entire AIS sample. The prevalence of low bone quality in AIS patients was 20.5%. However, there were no correlations between the SOS and types of scoliosis (P > .05). The SOS values among different severity groups were significant, particularly between the 10° to 19° and 20° to 39° groups as well as between 10° to 19° and ≥40° groups. However, there was no significant correlation between the SOS and Cobb angles. Significant correlations were also found between the pre- and post-menarchy status in patients. There was a significant difference in the SOS values for different Rissers' signs (P < .05). Compared to nonscoliotic controls, subjects with AIS had a generally lower SOS, indicating lower bone quality. The age, Risser's sign, or maturation status, may have an effect on the bone quality; however, the curve type and magnitude do not affect the bone quality. The results of this study indicate that slower bone maturation may affect the bone quality in adolescents with AIS. Copyright © 2015 National University of Health Sciences. Published by Elsevier Inc. All rights reserved.

Measuring Software Product Quality: The ISO 25000 Series and CMMI

DTIC Science & Technology

2004-06-14

performance objectives” covers objectives and requirements for product quality, service quality , and process performance. Process performance objectives...such that product quality, service quality , and process performance attributes are measurable and controlled throughout the project (internal and

A Laser-Based Measuring System for Online Quality Control of Car Engine Block.

PubMed

Li, Xing-Qiang; Wang, Zhong; Fu, Lu-Hua

2016-11-08

For online quality control of car engine production, pneumatic measurement instrument plays an unshakeable role in measuring diameters inside engine block because of its portability and high-accuracy. To the limitation of its measuring principle, however, the working space between the pneumatic device and measured surface is too small to require manual operation. This lowers the measuring efficiency and becomes an obstacle to perform automatic measurement. In this article, a high-speed, automatic measuring system is proposed to take the place of pneumatic devices by using a laser-based measuring unit. The measuring unit is considered as a set of several measuring modules, where each of them acts like a single bore gauge and is made of four laser triangulation sensors (LTSs), which are installed on different positions and in opposite directions. The spatial relationship among these LTSs was calibrated before measurements. Sampling points from measured shaft holes can be collected by the measuring unit. A unified mathematical model was established for both calibration and measurement. Based on the established model, the relative pose between the measuring unit and measured workpiece does not impact the measuring accuracy. This frees the measuring unit from accurate positioning or adjustment, and makes it possible to realize fast and automatic measurement. The proposed system and method were finally validated by experiments.

A Laser-Based Measuring System for Online Quality Control of Car Engine Block

PubMed Central

Li, Xing-Qiang; Wang, Zhong; Fu, Lu-Hua

2016-01-01

For online quality control of car engine production, pneumatic measurement instrument plays an unshakeable role in measuring diameters inside engine block because of its portability and high-accuracy. To the limitation of its measuring principle, however, the working space between the pneumatic device and measured surface is too small to require manual operation. This lowers the measuring efficiency and becomes an obstacle to perform automatic measurement. In this article, a high-speed, automatic measuring system is proposed to take the place of pneumatic devices by using a laser-based measuring unit. The measuring unit is considered as a set of several measuring modules, where each of them acts like a single bore gauge and is made of four laser triangulation sensors (LTSs), which are installed on different positions and in opposite directions. The spatial relationship among these LTSs was calibrated before measurements. Sampling points from measured shaft holes can be collected by the measuring unit. A unified mathematical model was established for both calibration and measurement. Based on the established model, the relative pose between the measuring unit and measured workpiece does not impact the measuring accuracy. This frees the measuring unit from accurate positioning or adjustment, and makes it possible to realize fast and automatic measurement. The proposed system and method were finally validated by experiments. PMID:27834839

A Total Quality-Control Plan with Right-Sized Statistical Quality-Control.

PubMed

Westgard, James O

2017-03-01

A new Clinical Laboratory Improvement Amendments option for risk-based quality-control (QC) plans became effective in January, 2016. Called an Individualized QC Plan, this option requires the laboratory to perform a risk assessment, develop a QC plan, and implement a QC program to monitor ongoing performance of the QC plan. Difficulties in performing a risk assessment may limit validity of an Individualized QC Plan. A better alternative is to develop a Total QC Plan including a right-sized statistical QC procedure to detect medically important errors. Westgard Sigma Rules provides a simple way to select the right control rules and the right number of control measurements. Copyright © 2016 Elsevier Inc. All rights reserved.

A whole process quality control system for energy measuring instruments inspection based on IOT technology

NASA Astrophysics Data System (ADS)

Yin, Bo; Liu, Li; Wang, Jiahan; Li, Xiran; Liu, Zhenbo; Li, Dewei; Wang, Jun; Liu, Lu; Wu, Jun; Xu, Tingting; Cui, He

2017-10-01

Electric energy measurement as a basic work, an accurate measurements play a vital role for the economic interests of both parties of power supply, the standardized management of the measurement laboratory at all levels is a direct factor that directly affects the fairness of measurement. Currently, the management of metering laboratories generally uses one-dimensional bar code as the recognition object, advances the testing process by manual management, most of the test data requires human input to generate reports. There are many problems and potential risks in this process: Data cannot be saved completely, cannot trace the status of inspection, the inspection process isn't completely controllable and so on. For the provincial metrology center's actual requirements of the whole process management for the performance test of the power measuring appliances, using of large-capacity RF tags as a process management information media, we developed a set of general measurement experiment management system, formulated a standardized full performance test process, improved the raw data recording mode of experimental process, developed a storehouse automatic inventory device, established a strict test sample transfer and storage system, ensured that all the raw data of the inspection can be traced back, achieved full life-cycle control of the sample, significantly improved the quality control level and the effectiveness of inspection work.

Measuring Rural Hospital Quality

ERIC Educational Resources Information Center

Moscovice, Ira; Wholey, Douglas R.; Klingner, Jill; Knott, Astrid

2004-01-01

Increased interest in the measurement of hospital quality has been stimulated by accrediting bodies, purchaser coalitions, government agencies, and other entities. This paper examines quality measurement for hospitals in rural settings. We seek to identify rural hospital quality measures that reflect quality in all hospitals and that are sensitive…

10 CFR 71.125 - Control of measuring and test equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... MATERIAL Quality Assurance § 71.125 Control of measuring and test equipment. The licensee, certificate holder, and applicant for a CoC shall establish measures to assure that tools, gauges, instruments, and other measuring and testing devices used in activities affecting quality are properly controlled...

Environmental controls and avoidance measures.

PubMed

Krouse, Helene J

2014-09-01

Environmental control measures refer to using 1 or more interventions aimed at avoiding, reducing, or eliminating allergens and irritants in the environment to improve symptoms of allergic rhinitis. Although avoiding known allergens is highly effective, completely eliminating an allergen from one's environment is often impractical or even impossible. The purpose of this work is to review evidence on the efficacy of various environmental control measures aimed at preventing the development of new sensitizations, reducing the progression of allergic rhinitis, and improving its symptoms and quality of life. Current literature examining the protective effects of specific measures such as breastfeeding and early pet exposure against the development of allergic diseases including allergic rhinitis has been inconclusive. Environmental measures such as frequently washing cats and dogs, encasing bedding within impermeable covers, air filtration, and chemicals can effectively reduce levels of allergens in the home. Although environmental control measures reduce allergen exposure levels, significant alleviation in symptoms or improvement in quality of life in patients with allergic rhinitis have not been shown. An evidence-based approach can assist health providers in educating patients and helping them to make informed decisions in selecting the most appropriate and cost-effective environmental control strategies to manage their disease. The greatest benefits can be achieved from using a multifaceted environmental approach aimed at routinely and systematically reducing exposure to allergens over time. © 2014 ARS-AAOA, LLC.

Genome measures used for quality control are dependent on gene function and ancestry.

PubMed

Wang, Jing; Raskin, Leon; Samuels, David C; Shyr, Yu; Guo, Yan

2015-02-01

The transition/transversion (Ti/Tv) ratio and heterozygous/nonreference-homozygous (het/nonref-hom) ratio have been commonly computed in genetic studies as a quality control (QC) measurement. Additionally, these two ratios are helpful in our understanding of the patterns of DNA sequence evolution. To thoroughly understand these two genomic measures, we performed a study using 1000 Genomes Project (1000G) released genotype data (N=1092). An additional two datasets (N=581 and N=6) were used to validate our findings from the 1000G dataset. We compared the two ratios among continental ancestry, genome regions and gene functionality. We found that the Ti/Tv ratio can be used as a quality indicator for single nucleotide polymorphisms inferred from high-throughput sequencing data. The Ti/Tv ratio varies greatly by genome region and functionality, but not by ancestry. The het/nonref-hom ratio varies greatly by ancestry, but not by genome regions and functionality. Furthermore, extreme guanine + cytosine content (either high or low) is negatively associated with the Ti/Tv ratio magnitude. Thus, when performing QC assessment using these two measures, care must be taken to apply the correct thresholds based on ancestry and genome region. Failure to take these considerations into account at the QC stage will bias any following analysis. yan.guo@vanderbilt.edu Supplementary data are available at Bioinformatics online. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Proteomics Quality Control: Quality Control Software for MaxQuant Results.

PubMed

Bielow, Chris; Mastrobuoni, Guido; Kempa, Stefan

2016-03-04

Mass spectrometry-based proteomics coupled to liquid chromatography has matured into an automatized, high-throughput technology, producing data on the scale of multiple gigabytes per instrument per day. Consequently, an automated quality control (QC) and quality analysis (QA) capable of detecting measurement bias, verifying consistency, and avoiding propagation of error is paramount for instrument operators and scientists in charge of downstream analysis. We have developed an R-based QC pipeline called Proteomics Quality Control (PTXQC) for bottom-up LC-MS data generated by the MaxQuant software pipeline. PTXQC creates a QC report containing a comprehensive and powerful set of QC metrics, augmented with automated scoring functions. The automated scores are collated to create an overview heatmap at the beginning of the report, giving valuable guidance also to nonspecialists. Our software supports a wide range of experimental designs, including stable isotope labeling by amino acids in cell culture (SILAC), tandem mass tags (TMT), and label-free data. Furthermore, we introduce new metrics to score MaxQuant's Match-between-runs (MBR) functionality by which peptide identifications can be transferred across Raw files based on accurate retention time and m/z. Last but not least, PTXQC is easy to install and use and represents the first QC software capable of processing MaxQuant result tables. PTXQC is freely available at https://github.com/cbielow/PTXQC .

10 CFR 72.164 - Control of measuring and test equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., instruments, and other measuring and testing devices used in activities affecting quality are properly... WASTE Quality Assurance § 72.164 Control of measuring and test equipment. The licensee, applicant for a... 10 Energy 2 2010-01-01 2010-01-01 false Control of measuring and test equipment. 72.164 Section 72...

Implementing self sustained quality control procedures in a clinical laboratory.

PubMed

Khatri, Roshan; K C, Sanjay; Shrestha, Prabodh; Sinha, J N

2013-01-01

Quality control is an essential component in every clinical laboratory which maintains the excellence of laboratory standards, supplementing to proper disease diagnosis, patient care and resulting in overall strengthening of health care system. Numerous quality control schemes are available, with combinations of procedures, most of which are tedious, time consuming and can be "too technical" whereas commercially available quality control materials can be expensive especially for laboratories in developing nations like Nepal. Here, we present a procedure performed at our centre with self prepared control serum and use of simple statistical tools for quality assurance. The pooled serum was prepared as per guidelines for preparation of stabilized liquid quality control serum from human sera. Internal Quality Assessment was performed on this sample, on a daily basis which included measurement of 12 routine biochemical parameters. The results were plotted on Levey-Jennings charts and analysed with quality control rules, for a period of one month. The mean levels of biochemical analytes in self prepared control serum were within normal physiological range. This serum was evaluated every day along with patients' samples. The results obtained were plotted on control charts and analysed using common quality control rules to identify possible systematic and random errors. Immediate mitigation measures were taken and the dispatch of erroneous reports was avoided. In this study we try to highlight on a simple internal quality control procedure which can be performed by laboratories, with minimum technology, expenditure, and expertise and improve reliability and validity of the test reports.

A multiple objective optimization approach to quality control

NASA Technical Reports Server (NTRS)

Seaman, Christopher Michael

1991-01-01

The use of product quality as the performance criteria for manufacturing system control is explored. The goal in manufacturing, for economic reasons, is to optimize product quality. The problem is that since quality is a rather nebulous product characteristic, there is seldom an analytic function that can be used as a measure. Therefore standard control approaches, such as optimal control, cannot readily be applied. A second problem with optimizing product quality is that it is typically measured along many dimensions: there are many apsects of quality which must be optimized simultaneously. Very often these different aspects are incommensurate and competing. The concept of optimality must now include accepting tradeoffs among the different quality characteristics. These problems are addressed using multiple objective optimization. It is shown that the quality control problem can be defined as a multiple objective optimization problem. A controller structure is defined using this as the basis. Then, an algorithm is presented which can be used by an operator to interactively find the best operating point. Essentially, the algorithm uses process data to provide the operator with two pieces of information: (1) if it is possible to simultaneously improve all quality criteria, then determine what changes to the process input or controller parameters should be made to do this; and (2) if it is not possible to improve all criteria, and the current operating point is not a desirable one, select a criteria in which a tradeoff should be made, and make input changes to improve all other criteria. The process is not operating at an optimal point in any sense if no tradeoff has to be made to move to a new operating point. This algorithm ensures that operating points are optimal in some sense and provides the operator with information about tradeoffs when seeking the best operating point. The multiobjective algorithm was implemented in two different injection molding scenarios

Theory and practice for measuring health care quality

PubMed Central

Berwick, Donald M.; Knapp, Marian Gilbert

1987-01-01

As competition, cost control, and new modes of delivery emerge in health care, there is a need to reexamine both the traditional definitions of health care quality and the methods by which it is measured. Industries other than health care have much to teach regarding the methods for obtaining, analyzing, and displaying data; techniques for problem identification, problem solving, and reassessment; and ideas about organizational factors that produce a high quality product or service. The Quality-of-Care Measurement Department at the Harvard Community Health Plan has built a program that draws from a distinguished health care quality assurance tradition and incorporates techniques that have been successful in other industries. PMID:10312319

Quality control quantification (QCQ): a tool to measure the value of quality control checks in radiation oncology.

PubMed

Ford, Eric C; Terezakis, Stephanie; Souranis, Annette; Harris, Kendra; Gay, Hiram; Mutic, Sasa

2012-11-01

To quantify the error-detection effectiveness of commonly used quality control (QC) measures. We analyzed incidents from 2007-2010 logged into a voluntary in-house, electronic incident learning systems at 2 academic radiation oncology clinics. None of the incidents resulted in patient harm. Each incident was graded for potential severity using the French Nuclear Safety Authority scoring scale; high potential severity incidents (score >3) were considered, along with a subset of 30 randomly chosen low severity incidents. Each report was evaluated to identify which of 15 common QC checks could have detected it. The effectiveness was calculated, defined as the percentage of incidents that each QC measure could detect, both for individual QC checks and for combinations of checks. In total, 4407 incidents were reported, 292 of which had high-potential severity. High- and low-severity incidents were detectable by 4.0 ± 2.3 (mean ± SD) and 2.6 ± 1.4 QC checks, respectively (P<.001). All individual checks were less than 50% sensitive with the exception of pretreatment plan review by a physicist (63%). An effectiveness of 97% was achieved with 7 checks used in combination and was not further improved with more checks. The combination of checks with the highest effectiveness includes physics plan review, physician plan review, Electronic Portal Imaging Device-based in vivo portal dosimetry, radiation therapist timeout, weekly physics chart check, the use of checklists, port films, and source-to-skin distance checks. Some commonly used QC checks such as pretreatment intensity modulated radiation therapy QA do not substantially add to the ability to detect errors in these data. The effectiveness of QC measures in radiation oncology depends sensitively on which checks are used and in which combinations. A small percentage of errors cannot be detected by any of the standard formal QC checks currently in broad use, suggesting that further improvements are needed. These data

Quality Leadership and Quality Control

PubMed Central

Badrick, Tony

2003-01-01

Different quality control rules detect different analytical errors with varying levels of efficiency depending on the type of error present, its prevalence and the number of observations. The efficiency of a rule can be gauged by inspection of a power function graph. Control rules are only part of a process and not an end in itself; just as important are the trouble-shooting systems employed when a failure occurs. 'Average of patient normals' may develop as a usual adjunct to conventional quality control serum based programmes. Acceptable error can be based on various criteria; biological variation is probably the most sensible. Once determined, acceptable error can be used as limits in quality control rule systems. A key aspect of an organisation is leadership, which links the various components of the quality system. Leadership is difficult to characterise but its key aspects include trust, setting an example, developing staff and critically setting the vision for the organisation. Organisations also have internal characteristics such as the degree of formalisation, centralisation, and complexity. Medical organisations can have internal tensions because of the dichotomy between the bureaucratic and the shadow medical structures. PMID:18568046

Downhole steam quality measurement

DOEpatents

Lee, D.O.; Montoya, P.C.; Muir, J.F.; Wayland, J.R. Jr.

1985-06-19

The present invention relates to an empirical electrical method for remote sensing of steam quality utilizing flow-through grids which allow measurement of the electrical properties of a flowing two-phase mixture. The measurement of steam quality in the oil field is important to the efficient application of steam assisted recovery of oil. Because of the increased energy content in higher quality steam it is important to maintain the highest possible steam quality at the injection sandface. The effectiveness of a steaming operation without a measure of steam quality downhole close to the point of injection would be difficult to determine. Therefore, a need exists for the remote sensing of steam quality.

Principles and Practices for Quality Assurance and Quality Control

USGS Publications Warehouse

Jones, Berwyn E.

1999-01-01

Quality assurance and quality control are vital parts of highway runoff water-quality monitoring projects. To be effective, project quality assurance must address all aspects of the project, including project management responsibilities and resources, data quality objectives, sampling and analysis plans, data-collection protocols, data quality-control plans, data-assessment procedures and requirements, and project outputs. Quality control ensures that the data quality objectives are achieved as planned. The historical development and current state of the art of quality assurance and quality control concepts described in this report can be applied to evaluation of data from prior projects.

Redefining Quality Measurement in Cancer Care.

PubMed

Nardi, Elizabeth A; McCanney, James; Winckworth-Prejsnar, Katy; Schatz, Alyssa A; Adelson, Kerin; Neubauer, Marcus; Smith, Mary Lou; Walters, Ronald; Carlson, Robert W

2018-05-01

Quality measurement in oncology is increasing in significance as payment schemes shift from volume to value. As demand for quality measures increases, challenges in the development of quality measures, standardization across measures, and the limitations of health information technology have become apparent. Moreover, the time and financial burden associated with developing, tracking, and reporting quality measures are substantial. Despite these challenges, best practices and leaders in the field of quality measurement in oncology have emerged. To understand the current challenges and promising practices in quality measurement and to explore future considerations for measure development and measure reporting in oncology, NCCN convened the NCCN Policy Summit: Redefining Quality Measurement in Oncology. The summit included discussion of the current quality landscape and efforts to develop quality measures, use of quality measures in various programs, patient perspective of quality, and challenges and best practices for quality reporting. Copyright © 2018 by the National Comprehensive Cancer Network.

A proteomics performance standard to support measurement quality in proteomics.

PubMed

Beasley-Green, Ashley; Bunk, David; Rudnick, Paul; Kilpatrick, Lisa; Phinney, Karen

2012-04-01

The emergence of MS-based proteomic platforms as a prominent technology utilized in biochemical and biomedical research has increased the need for high-quality MS measurements. To address this need, National Institute of Standards and Technology (NIST) reference material (RM) 8323 yeast protein extract is introduced as a proteomics quality control material for benchmarking the preanalytical and analytical performance of proteomics-based experimental workflows. RM 8323 yeast protein extract is based upon the well-characterized eukaryote Saccharomyces cerevisiae and can be utilized in the design and optimization of proteomics-based methodologies from sample preparation to data analysis. To demonstrate its utility as a proteomics quality control material, we coupled LC-MS/MS measurements of RM 8323 with the NIST MS Quality Control (MSQC) performance metrics to quantitatively assess the LC-MS/MS instrumentation parameters that influence measurement accuracy, repeatability, and reproducibility. Due to the complexity of the yeast proteome, we also demonstrate how NIST RM 8323, along with the NIST MSQC performance metrics, can be used in the evaluation and optimization of proteomics-based sample preparation methods. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Multi-Agent Architecture with Support to Quality of Service and Quality of Control

NASA Astrophysics Data System (ADS)

Poza-Luján, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, Jose-Enrique

Multi Agent Systems (MAS) are one of the most suitable frameworks for the implementation of intelligent distributed control system. Agents provide suitable flexibility to give support to implied heterogeneity in cyber-physical systems. Quality of Service (QoS) and Quality of Control (QoC) parameters are commonly utilized to evaluate the efficiency of the communications and the control loop. Agents can use the quality measures to take a wide range of decisions, like suitable placement on the control node or to change the workload to save energy. This article describes the architecture of a multi agent system that provides support to QoS and QoC parameters to optimize de system. The architecture uses a Publish-Subscriber model, based on Data Distribution Service (DDS) to send the control messages. Due to the nature of the Publish-Subscribe model, the architecture is suitable to implement event-based control (EBC) systems. The architecture has been called FSACtrl.

An approach for estimating measurement uncertainty in medical laboratories using data from long-term quality control and external quality assessment schemes.

PubMed

Padoan, Andrea; Antonelli, Giorgia; Aita, Ada; Sciacovelli, Laura; Plebani, Mario

2017-10-26

The present study was prompted by the ISO 15189 requirements that medical laboratories should estimate measurement uncertainty (MU). The method used to estimate MU included the: a) identification of quantitative tests, b) classification of tests in relation to their clinical purpose, and c) identification of criteria to estimate the different MU components. Imprecision was estimated using long-term internal quality control (IQC) results of the year 2016, while external quality assessment schemes (EQAs) results obtained in the period 2015-2016 were used to estimate bias and bias uncertainty. A total of 263 measurement procedures (MPs) were analyzed. On the basis of test purpose, in 51 MPs imprecision only was used to estimate MU; in the remaining MPs, the bias component was not estimable for 22 MPs because EQAs results did not provide reliable statistics. For a total of 28 MPs, two or more MU values were calculated on the basis of analyte concentration levels. Overall, results showed that uncertainty of bias is a minor factor contributing to MU, the bias component being the most relevant contributor to all the studied sample matrices. The model chosen for MU estimation allowed us to derive a standardized approach for bias calculation, with respect to the fitness-for-purpose of test results. Measurement uncertainty estimation could readily be implemented in medical laboratories as a useful tool in monitoring the analytical quality of test results since they are calculated using a combination of both the long-term imprecision IQC results and bias, on the basis of EQAs results.

Quality Control Barriers in Adapting "Metro-Centric" Education to Regional Needs

ERIC Educational Resources Information Center

Nagy, Judy; Robinson, Susan R.

2013-01-01

The massification and globalization of higher education, combined with the widespread adoption of processes underpinning accreditation and quality control of university programs, have tended to result in learning contexts that are increasingly narrowly conceived and tightly controlled. Underlying many quality control measures is a "one size…

Poor sleep quality has an adverse effect on childhood asthma control and lung function measures.

PubMed

Sheen, Youn Ho; Choi, Sun Hee; Jang, Sun Jung; Baek, Ji Hyeon; Jee, Hye Mi; Kim, Mi Ae; Chae, Kyu Young; Han, Man Yong

2017-08-01

It is unclear as to whether sleep respiratory breathing disorder (SRBD) is a risk factor for uncontrolled asthma in children. The aim of this study was therefore to investigate whether SRBD may have an adverse effect on childhood asthma control and lung function measures. This was a cross-sectional study of 220 children with well-controlled (n = 108), partly controlled (n = 92), and uncontrolled asthma (n = 20) according to the Global Initiative for Asthma guideline. SRBD was assessed using the Pediatric Sleep Questionnaire (PSQ). The association of SRBD with partly controlled/uncontrolled asthma was investigated on multivariate logistic regression analysis. Of 220 children with asthma, 43 (19.6%) had SRBD: well-controlled, 16.7% (18/108); partly controlled, 21.7% (20/92); and uncontrolled, 25.0% (5/20; P = 0.54). There was a significant difference in forced expiratory volume in 1 s/forced vital capacity (FEV 1 /FVC; P = 0.007) and childhood asthma control test (C-ACT) score (P < 0.001) according to asthma control status, but not in PSQ score (P = 0.18). Children with obstructive sleep apnea (PSQ >0.33) had a lower C-ACT score compared with controls (PSQ ≤0.33; 19.6 ± 5.1 vs 22.0 ± 4.2, P = 0.002). PSQ score was negatively correlated with FEV 1 /FVC (r = -0.16, P = 0.02). On multivariate logistic regression analysis, high PSQ score increased the odds of having partly controlled/uncontrolled asthma by 9.12 (95% CI: 1.04-79.72, P = 0.046) after adjusting for confounding factors. SRBD is an independent risk factor for partly controlled/uncontrolled asthma and has an adverse effect on lung function measures in children. Further research is warranted to determine whether the improvement of sleep quality may also enhance level of asthma control and lung function in children. © 2017 Japan Pediatric Society.

Quality measures in applications of image restoration.

PubMed

Kriete, A; Naim, M; Schafer, L

2001-01-01

We describe a new method for the estimation of image quality in image restoration applications. We demonstrate this technique on a simulated data set of fluorescent beads, in comparison with restoration by three different deconvolution methods. Both the number of iterations and a regularisation factor are varied to enforce changes in the resulting image quality. First, the data sets are directly compared by an accuracy measure. These values serve to validate the image quality descriptor, which is developed on the basis of optical information theory. This most general measure takes into account the spectral energies and the noise, weighted in a logarithmic fashion. It is demonstrated that this method is particularly helpful as a user-oriented method to control the output of iterative image restorations and to eliminate the guesswork in choosing a suitable number of iterations.

Use of multiple sensor technologies for quality control of in situ biogeochemical measurements: A SeaCycler case study

NASA Astrophysics Data System (ADS)

Atamanchuk, Dariia; Koelling, Jannes; Lai, Jeremy; Send, Uwe; Wallace, Douglas

2017-04-01

Over the last two decades observing capacity for the global ocean has increased dramatically. Emerging sensor technologies for dissolved gases, nutrients and bio-optical properties in seawater are allowing extension of in situ observations beyond the traditionally measured salinity, temperature and pressure (CTD). However the effort to extend observations using autonomous instruments and platforms carries the risk of losing the level of data quality achievable through conventional water sampling techniques. We will present results from a case study with the SeaCycler profiling winch focusing on quality control of the in-situ measurements. A total of 13 sensors were deployed from May 2016 to early 2017 on SeaCycler's profiling sensor float, including CTD, dissolved oxygen (O2, 3 sensors), carbon dioxide (pCO2, 2 sensors), nutrients, velocity sensors, fluorometer, transmissometer, single channel PAR sensor, and others. We will highlight how multiple measurement technologies (e.g. for O2 and CO2) complement each other and result in a high quality data product. We will also present an initial assessment of the bio-optical data, their implications for seasonal phytoplankton dynamics and comparisons to climatologies and ocean-color data products obtained from the MODIS satellite.

QUALITY CONTROLS FOR PCR

EPA Science Inventory

The purpose of this presentation is to present an overview of the quality control (QC) sections of a draft EPA document entitled, "Quality Assurance/Quality Control Guidance for Laboratories Performing PCR Analyses on Environmental Samples." This document has been prepared by th...

Downhole steam quality measurement

DOEpatents

Lee, David O.; Montoya, Paul C.; Muir, James F.; Wayland, Jr., J. Robert

1987-01-01

An empirical method for the remote sensing of steam quality that can be easily adapted to downhole steam quality measurements by measuring the electrical properties of two-phase flow across electrode grids at low frequencies.

Patients’ perceived value of pharmacy quality measures: a mixed-methods study

PubMed Central

Shiyanbola, Olayinka O; Mort, Jane R

2015-01-01

Objective To describe patients’ perceived value and use of quality measures in evaluating and choosing community pharmacies. Design Focus group methodology was combined with a survey tool. During the focus groups, participants assessed the value of the Pharmacy Quality Alliance's quality measures in evaluating and choosing a pharmacy. Also, participants completed questionnaires rating their perceived value of quality measures in evaluating a pharmacy (1 being low value and 5 being high) or choosing a pharmacy (yes/no). Thematic analysis and descriptive statistics were used to analyse the focus groups and surveys, respectively. Setting Semistructured focus groups were conducted in a private meeting space of an urban and a rural area of a Mid-western State in the USA. Participants Thirty-four adults who filled prescription medications in community pharmacies for a chronic illness were recruited in community pharmacies, senior centres and public libraries. Results While comments indicated that all measures were important, medication safety measures (eg, drug-drug interactions) were valued more highly than others. Rating of quality measure utility in evaluating a pharmacy ranged from a mean of 4.88 (‘drug-drug interactions’) to a mean of 4.0 (‘absence of controller therapy for patients with asthma’). Patients were hesitant to use quality information in choosing a pharmacy (depending on the participant's location) but might consider if moving to a new area or having had a negative pharmacy experience. Use of select quality measures to choose a pharmacy ranged from 97.1% of participants using ‘drug-drug interactions’ (medication safety measure) to 55.9% using ‘absence of controller therapy for patients with asthma’. Conclusions The study participants valued quality measures in evaluating and selecting a community pharmacy, with medication safety measures valued highest. The participants reported that the quality measures would not typically cause a

Performance of biometric quality measures.

PubMed

Grother, Patrick; Tabassi, Elham

2007-04-01

We document methods for the quantitative evaluation of systems that produce a scalar summary of a biometric sample's quality. We are motivated by a need to test claims that quality measures are predictive of matching performance. We regard a quality measurement algorithm as a black box that converts an input sample to an output scalar. We evaluate it by quantifying the association between those values and observed matching results. We advance detection error trade-off and error versus reject characteristics as metrics for the comparative evaluation of sample quality measurement algorithms. We proceed this with a definition of sample quality, a description of the operational use of quality measures. We emphasize the performance goal by including a procedure for annotating the samples of a reference corpus with quality values derived from empirical recognition scores.

Air quality and ventilation fan control based on aerosol measurement in the bi-directional undersea Bømlafjord tunnel.

PubMed

Indrehus, Oddny; Aralt, Tor Tybring

2005-04-01

Aerosol, NO and CO concentration, temperature, air humidity, air flow and number of running ventilation fans were measured by continuous analysers every minute for a whole week for six different one-week periods spread over ten months in 2001 and 2002 at measuring stations in the 7860 m long tunnel. The ventilation control system was mainly based on aerosol measurements taken by optical scatter sensors. The ventilation turned out to be satisfactory according to Norwegian air quality standards for road tunnels; however, there was some uncertainty concerning the NO2 levels. The air humidity and temperature inside the tunnel were highly influenced by the outside metrological conditions. Statistical models for NO concentration were developed and tested; correlations between predicted and measured NO were 0.81 for a partial least squares regression (PLS1) model based on CO and aerosol, and 0.77 for a linear regression model based only on aerosol. Hence, the ventilation control system should not solely be based on aerosol measurements. Since NO2 is the hazardous polluter, modelling NO2 concentration rather than NO should be preferred in any further optimising of the ventilation control.

Standard Reference Specimens in Quality Control of Engineering Surfaces

PubMed Central

Song, J. F.; Vorburger, T. V.

1991-01-01

In the quality control of engineering surfaces, we aim to understand and maintain a good relationship between the manufacturing process and surface function. This is achieved by controlling the surface texture. The control process involves: 1) learning the functional parameters and their control values through controlled experiments or through a long history of production and use; 2) maintaining high accuracy and reproducibility with measurements not only of roughness calibration specimens but also of real engineering parts. In this paper, the characteristics, utilizations, and limitations of different classes of precision roughness calibration specimens are described. A measuring procedure of engineering surfaces, based on the calibration procedure of roughness specimens at NIST, is proposed. This procedure involves utilization of check specimens with waveform, wavelength, and other roughness parameters similar to functioning engineering surfaces. These check specimens would be certified under standardized reference measuring conditions, or by a reference instrument, and could be used for overall checking of the measuring procedure and for maintaining accuracy and agreement in engineering surface measurement. The concept of “surface texture design” is also suggested, which involves designing the engineering surface texture, the manufacturing process, and the quality control procedure to meet the optimal functional needs. PMID:28184115

[On-site quality control of acupuncture randomized controlled trial: design of content and checklist of quality control based on PICOST].

PubMed

Li, Hong-Jiao; He, Li-Yun; Liu, Zhi-Shun; Sun, Ya-Nan; Yan, Shi-Yan; Liu, Jia; Zhao, Ye; Liu, Bao-Yan

2014-02-01

To effectively guarantee quality of randomized controlld trial (RCT) of acupuncture and develop reasonable content and checklist of on-site quality control, influencing factors on quality of acupuncture RCT are analyzed and scientificity of quality control content and feasibility of on-site manipulation are put into overall consideration. Based on content and checklist of on-site quality control in National 11th Five-Year Plan Project Optimization of Comprehensive Treatment Plan for TCM in Prevention and Treatment of Serious Disease and Clinical Assessment on Generic Technology and Quality Control Research, it is proposed that on-site quality control of acupuncture RCT should be conducted with PICOST (patient, intervention, comparison, out come, site and time) as core, especially on quality control of interveners' skills and outcome assessment of blinding, and checklist of on-site quality control is developed to provide references for undertaking groups of the project.

Quality measurement in diabetes care.

PubMed

Leas, Brian F; Berman, Bettina; Kash, Kathryn M; Crawford, Albert G; Toner, Richard W; Goldfarb, Neil I; Nash, David B

2009-10-01

This study aimed to evaluate diabetes quality measurement efforts, assess their strengths and areas for improvement, and identify gaps not adequately addressed by these measures. We conducted an environmental scan of diabetes quality measures, focusing on metrics included in the National Quality Measures Clearinghouse or promulgated by leading measurement organizations. Key informant interviews were also completed with thought leaders who develop, promote, and use quality measures. The environmental scan identified 146 distinct measures spanning 31 clinical processes or outcomes. This suggests a measurement system that is both redundant and inconsistent, with many different measures assessing the same clinical indicators. Interviewees believe that current diabetes measurement efforts are excessively broad and complex and expressed a need for better harmonization of these measures. Several gaps were also found, including a lack of measures focusing on population health, structural elements of health care, and prevention of diabetes.

Internal quality control: planning and implementation strategies.

PubMed

Westgard, James O

2003-11-01

The first essential in setting up internal quality control (IQC) of a test procedure in the clinical laboratory is to select the proper IQC procedure to implement, i.e. choosing the statistical criteria or control rules, and the number of control measurements, according to the quality required for the test and the observed performance of the method. Then the right IQC procedure must be properly implemented. This review focuses on strategies for planning and implementing IQC procedures in order to improve the quality of the IQC. A quantitative planning process is described that can be implemented with graphical tools such as power function or critical-error graphs and charts of operating specifications. Finally, a total QC strategy is formulated to minimize cost and maximize quality. A general strategy for IQC implementation is recommended that employs a three-stage design in which the first stage provides high error detection, the second stage low false rejection and the third stage prescribes the length of the analytical run, making use of an algorithm involving the average of normal patients' data.

Quality Control/Assurance in Post Secondary Education: An Outcomes Approach. AIR 1988 Annual Forum Paper.

ERIC Educational Resources Information Center

Birch, Derek W.; Johnson, F. Craig

A study was conducted using quality control and quality assurance models to examine student outcomes. The purpose was to investigate current quality control and quality assurance practices in six colleges, to evaluate the relationship between quantitative effectiveness measures and qualitative outcomes measure and to assess the readiness of each…

Analysis of quality control data of eight modern radiotherapy linear accelerators: the short- and long-term behaviours of the outputs and the reproducibility of quality control measurements

NASA Astrophysics Data System (ADS)

Kapanen, Mika; Tenhunen, Mikko; Hämäläinen, Tuomo; Sipilä, Petri; Parkkinen, Ritva; Järvinen, Hannu

2006-07-01

Quality control (QC) data of radiotherapy linear accelerators, collected by Helsinki University Central Hospital between the years 2000 and 2004, were analysed. The goal was to provide information for the evaluation and elaboration of QC of accelerator outputs and to propose a method for QC data analysis. Short- and long-term drifts in outputs were quantified by fitting empirical mathematical models to the QC measurements. Normally, long-term drifts were well (<=1%) modelled by either a straight line or a single-exponential function. A drift of 2% occurred in 18 ± 12 months. The shortest drift times of only 2-3 months were observed for some new accelerators just after the commissioning but they stabilized during the first 2-3 years. The short-term reproducibility and the long-term stability of local constancy checks, carried out with a sealed plane parallel ion chamber, were also estimated by fitting empirical models to the QC measurements. The reproducibility was 0.2-0.5% depending on the positioning practice of a device. Long-term instabilities of about 0.3%/month were observed for some checking devices. The reproducibility of local absorbed dose measurements was estimated to be about 0.5%. The proposed empirical model fitting of QC data facilitates the recognition of erroneous QC measurements and abnormal output behaviour, caused by malfunctions, offering a tool to improve dose control.

A quality control circle process to improve implementation effect of prevention measures for high-risk patients.

PubMed

Feng, Haixia; Li, Guohong; Xu, Cuirong; Ju, Changping; Suo, Peiheng

2017-12-01

The aim of the study was to analyse the influence of prevention measures on pressure injuries for high-risk patients and to establish the most appropriate methods of implementation. Nurses assessed patients using a checklist and factors influencing the prevention of a pressure injury determined by brain storming. A specific series of measures was drawn up and an estimate of risk of pressure injury determined using the Braden Scale, analysis of nursing documents, implementation of prevention measures for pressure sores and awareness of the system both before and after carrying out a quality control circle (QCC) process. The overall scores of implementation of prevention measures ranged from 74.86 ± 14.24 to 87.06 ± 17.04, a result that was statistically significant (P < 0.0025). The Braden Scale scores ranged from 8.53 ± 3.21 to 13.48 ± 3.57. The nursing document scores ranged from 7.67 ± 3.98 to 10.12 ± 1.63; prevention measure scores ranged from 11.48 ± 4.18 to 13.96 ± 3.92. Differences in all of the above results are statistically significant (P < 0.05). Implementation of a QCC can standardise and improve the prevention measures for patients who are vulnerable to pressure sores and is of practical importance to their prevention and control. © 2017 Medicalhelplines.com Inc and John Wiley & Sons Ltd.

Commutability of control materials for external quality assessment of serum apolipoprotein A-I measurement.

PubMed

Zeng, Jie; Qi, Tianqi; Wang, Shu; Zhang, Tianjiao; Zhou, Weiyan; Zhao, Haijian; Ma, Rong; Zhang, Jiangtao; Yan, Ying; Dong, Jun; Zhang, Chuanbao; Chen, Wenxiang

2018-04-25

The aim of the current study was to evaluate the commutability of commercial control materials and human serum pools and to investigate the suitability of the materials for the external quality assessment (EQA) of serum apolipoprotein A-I (apo A-I) measurement. The Clinical and Laboratory Standards Institute (CLSI) EP14-A3 protocol was used for the commutability study. Apo A-I concentrations in two levels of commercial control materials used in EQA program, two fresh-frozen human serum pools (FSPs) and two frozen human serum pools prepared from residual clinical specimens (RSPs) were measured along with 50 individual samples using nine commercial assays. Measurement results of the 50 individual samples obtained with different assays were pairwise analyzed by Deming regression, and 95% prediction intervals (PIs) were calculated. The commutability of the processed materials was evaluated by comparing the measurement results of the materials with the limits of the PIs. The FSP-1 was commutable for all the 36 assay pairs, and FSP-2 was commutable for 30 pairs; RSP-1 and RSP-2 showed commutability for 27/36 and 22/36 assay pairs, respectively, whereas the two EQA materials were commutable only for 4/36 and 5/36 assay pairs, respectively. Non-commutability of the tested EQA materials has been observed among current apo A-I assays. EQA programs need either to take into account the commutability-related biases in the interpretation of the EQA results or to use more commutable materials. Frozen human serum pools were commutable for most of the assays.

Review of Phosphorus Control Measures in the United States and Their Effects on Water Quality

USGS Publications Warehouse

Litke, David W.

1999-01-01

Historical information on phosphorus loadings to the environment and the effect on water quality are summarized in this report, which was produced as part of the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program. Phosphorus is a water-quality constituent of concern because it is often the limiting nutrient responsible for accelerated eutrophication in water bodies. Phosphorus inputs to the environment have increased since 1950 as the use of phosphate fertilizer, manure, and phosphate laundry detergent increased; however, the manufacture of phosphate detergent for household laundry was ended voluntarily in about 1994 after many States had established phosphate detergent bans. Total phosphorus concentrations in raw wastewater effluent contained about 3 milligrams per liter of total phosphorus during the 1940's, increased to about 11 milligrams per liter at the height of phosphate detergent use (1970), and have currently declined to about 5 milligrams per liter. However, in some cases, tertiary wastewater treatment still is needed to effectively improve water quality of streams. Downward trends in phosphorus concentrations since 1970 have been identified in many streams, but median total phosphorus concentrations still exceed the recommended limit of 0.1 milligram per liter across much of the Nation. Data from the NAWQA Program are representative of a variety of phosphorus-control measures, and, therefore, may be used to evaluate the effects of various control strategies. Current areas of concern include: evaluation of the effects of increased manure loadings of phosphorus on soil phosphorus and, subsequently, on ground water and subsurface runoff; determination of point-source and nonpoint-source components of phosphorus loads by geographic modeling and hydrologic separation techniques; and development of methods or indices to evaluate nutrient impairment in streams and rivers to serve as a basis for developing phosphorus criteria or

Measuring quality in anatomic pathology.

PubMed

Raab, Stephen S; Grzybicki, Dana Marie

2008-06-01

This article focuses mainly on diagnostic accuracy in measuring quality in anatomic pathology, noting that measuring any quality metric is complex and demanding. The authors discuss standardization and its variability within and across areas of care delivery and efforts involving defining and measuring error to achieve pathology quality and patient safety. They propose that data linking error to patient outcome are critical for developing quality improvement initiatives targeting errors that cause patient harm in addition to using methods of root cause analysis, beyond those traditionally used in cytologic-histologic correlation, to assist in the development of error reduction and quality improvement plans.

[Quality control in anesthesiology].

PubMed

Muñoz-Ramón, J M

1995-03-01

The process of quality control and auditing of anesthesiology allows us to evaluate care given by a service and solve problems that are detected. Quality control is a basic element of care giving and is only secondarily an area of academic research; it is therefore a meaningless effort if the information does not serve to improve departmental procedures. Quality assurance procedures assume certain infrastructural requirements and an initial period of implementation and adjustment. The main objectives of quality control are the reduction of morbidity and mortality due to anesthesia, assurance of the availability and proper management of resources and, finally, the well-being and safety of the patient.

Crowding measures associated with the quality of emergency department care: a systematic review.

PubMed

Stang, Antonia S; Crotts, Jennifer; Johnson, David W; Hartling, Lisa; Guttmann, Astrid

2015-06-01

Despite the substantial body of literature on emergency department (ED) crowding, to the best of our knowledge, there is no agreement on the measure or measures that should be used to quantify crowding. The objective of this systematic review was to identify existing measures of ED crowding that have been linked to quality of care as defined by the Institute of Medicine (IOM) quality domains (safe, effective, patient-centered, efficient, timely, and equitable). Six major bibliographic databases were searched from January 1980 to January 2012, and hand searches were conducted of relevant journals and conference proceedings. Observational studies (cross-sectional, cohort, and case-control), quality improvement studies, quasi-experimental (e.g., before/after) studies, and randomized controlled trials were considered for inclusion. Studies that did not provide measures of ED crowding were excluded. Studies that did not provide quantitative data on the link between crowding measures and quality of care were also excluded. Two independent reviewers assessed study eligibility, completed data extraction, and assessed study quality using the Newcastle-Ottawa Quality Assessment Scale (NOS) for observational studies and a modified version of the NOS for cross-sectional studies. The search identified 7,413 articles. Thirty-two articles were included in the review: six cross-sectional, one case-control, 23 cohort, and two retrospective reviews of performance improvement data. Methodologic quality was moderate, with weaknesses in the reporting of study design and methodology. Overall, 15 of the crowding measures studied had quantifiable links to quality of care. The three measures most frequently linked to quality of care were the number of patients in the waiting room, ED occupancy (percentage of overall ED beds filled), and the number of admitted patients in the ED awaiting inpatient beds. None of the articles provided data on the link between crowding measures and the IOM

Measuring the quality of therapeutic apheresis care in the pediatric intensive care unit.

PubMed

Sussmane, Jeffrey B; Torbati, Dan; Gitlow, Howard S

2012-01-01

Our goal was to measure the quality of care provided in the Pediatric Intensive Care Unit (PICU) during Therapeutic Apheresis (TA). We described the care as a step by step process. We designed a flow chart to carefully document each step of the process. We then defined each step with a unique clinical indictor (CI) that represented the exact task we felt provided quality care. These CIs were studied and modified for 1 year. We measured our performance in this process by the number of times we accomplished the CI vs. the total number of CIs that were to be performed. The degree of compliance, with these clinical indicators, was analyzed and used as a metric for quality by calculating how close the process is running exactly as planned or "in control." The Apheresis Process was in control (compliance) for 47% of the indicators, as measured in the aggregate for the first observational year. We then applied the theory of Total Quality Management (TQM) through our Design, Measure, Analyze, Improve, and Control (DMAIC) model. We were able to improve the process and bring it into control by increasing the compliance to > 99.74%, in the aggregate, for the third and fourth quarter of the second year. We have implemented TQM to increase compliance, thus control, of a highly complex and multidisciplinary Pediatric Intensive Care therapy. We have shown a reproducible and scalable measure of quality for a complex clinical process in the PICU, without additional capital expenditure. Copyright © 2011 Wiley-Liss, Inc.

Adaptive measurements of urban runoff quality

NASA Astrophysics Data System (ADS)

Wong, Brandon P.; Kerkez, Branko

2016-11-01

An approach to adaptively measure runoff water quality dynamics is introduced, focusing specifically on characterizing the timing and magnitude of urban pollutographs. Rather than relying on a static schedule or flow-weighted sampling, which can miss important water quality dynamics if parameterized inadequately, novel Internet-enabled sensor nodes are used to autonomously adapt their measurement frequency to real-time weather forecasts and hydrologic conditions. This dynamic approach has the potential to significantly improve the use of constrained experimental resources, such as automated grab samplers, which continue to provide a strong alternative to sampling water quality dynamics when in situ sensors are not available. Compared to conventional flow-weighted or time-weighted sampling schemes, which rely on preset thresholds, a major benefit of the approach is the ability to dynamically adapt to features of an underlying hydrologic signal. A 28 km2 urban watershed was studied to characterize concentrations of total suspended solids (TSS) and total phosphorus. Water quality samples were autonomously triggered in response to features in the underlying hydrograph and real-time weather forecasts. The study watershed did not exhibit a strong first flush and intraevent concentration variability was driven by flow acceleration, wherein the largest loadings of TSS and total phosphorus corresponded with the steepest rising limbs of the storm hydrograph. The scalability of the proposed method is discussed in the context of larger sensor network deployments, as well the potential to improving control of urban water quality.

Measuring Quality in Ethics Consultation.

PubMed

Bliss, Sally E; Oppenlander, Jane; Dahlke, Jacob M; Meyer, Gordon J; Williford, Eva M; Macauley, Robert C

2016-01-01

For all of the emphasis on quality improvement-as well as the acknowledged overlap between assessment of the quality of healthcare services and clinical ethics-the quality of clinical ethics consultation has received scant attention, especially in terms of empirical measurement. Recognizing this need, the second edition of Core Competencies for Health Care Ethics Consultation1 identified four domains of ethics quality: (1) ethicality, (2) stakeholders' satisfaction, (3) resolution of the presenting conflict/dilemma, and (4) education that translates into knowledge. This study is the first, to our knowledge, to directly measure all of these domains. Here we describe the quality improvement process undertaken at a tertiary care academic medical center, as well as the tools developed to measure the quality of ethics consultation, which include post-consultation satisfaction surveys and weekly case conferences. The information gained through these tools helps to improve not only the process of ethics consultation, but also the measurement and assurance of quality. Copyright 2016 The Journal of Clinical Ethics. All rights reserved.

Commercial jet fuel quality control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strauss, K.H.

1995-05-01

The paper discusses the purpose of jet fuel quality control between the refinery and the aircraft. It describes fixed equipment, including various types of filters, and the usefulness and limitations of this equipment. Test equipment is reviewed as are various surveillance procedures. These include the Air Transport Association specification ATA 103, the FAA Advisory Circular 150/5230-4, the International Air Transport Association Guidance Material for Fuel Quality Control and Fuelling Service and the Guidelines for Quality Control at Jointly Operated Fuel Systems. Some past and current quality control problems are briefly mentioned.

Interrupted Time Series Versus Statistical Process Control in Quality Improvement Projects.

PubMed

Andersson Hagiwara, Magnus; Andersson Gäre, Boel; Elg, Mattias

2016-01-01

To measure the effect of quality improvement interventions, it is appropriate to use analysis methods that measure data over time. Examples of such methods include statistical process control analysis and interrupted time series with segmented regression analysis. This article compares the use of statistical process control analysis and interrupted time series with segmented regression analysis for evaluating the longitudinal effects of quality improvement interventions, using an example study on an evaluation of a computerized decision support system.

Earnings Quality Measures and Excess Returns

PubMed Central

Perotti, Pietro; Wagenhofer, Alfred

2014-01-01

This paper examines how commonly used earnings quality measures fulfill a key objective of financial reporting, i.e., improving decision usefulness for investors. We propose a stock-price-based measure for assessing the quality of earnings quality measures. We predict that firms with higher earnings quality will be less mispriced than other firms. Mispricing is measured by the difference of the mean absolute excess returns of portfolios formed on high and low values of a measure. We examine persistence, predictability, two measures of smoothness, abnormal accruals, accruals quality, earnings response coefficient and value relevance. For a large sample of US non-financial firms over the period 1988–2007, we show that all measures except for smoothness are negatively associated with absolute excess returns, suggesting that smoothness is generally a favorable attribute of earnings. Accruals measures generate the largest spread in absolute excess returns, followed by smoothness and market-based measures. These results lend support to the widespread use of accruals measures as overall measures of earnings quality in the literature. PMID:26300582

Earnings Quality Measures and Excess Returns.

PubMed

Perotti, Pietro; Wagenhofer, Alfred

2014-06-01

This paper examines how commonly used earnings quality measures fulfill a key objective of financial reporting, i.e., improving decision usefulness for investors. We propose a stock-price-based measure for assessing the quality of earnings quality measures. We predict that firms with higher earnings quality will be less mispriced than other firms. Mispricing is measured by the difference of the mean absolute excess returns of portfolios formed on high and low values of a measure. We examine persistence, predictability, two measures of smoothness, abnormal accruals, accruals quality, earnings response coefficient and value relevance. For a large sample of US non-financial firms over the period 1988-2007, we show that all measures except for smoothness are negatively associated with absolute excess returns, suggesting that smoothness is generally a favorable attribute of earnings. Accruals measures generate the largest spread in absolute excess returns, followed by smoothness and market-based measures. These results lend support to the widespread use of accruals measures as overall measures of earnings quality in the literature.

Quality improvement in neurology: AAN Parkinson disease quality measures

PubMed Central

Cheng, E.M.; Tonn, S.; Swain-Eng, R.; Factor, S.A.; Weiner, W.J.; Bever, C.T.

2010-01-01

Background: Measuring the quality of health care is a fundamental step toward improving health care and is increasingly used in pay-for-performance initiatives and maintenance of certification requirements. Measure development to date has focused on primary care and common conditions such as diabetes; thus, the number of measures that apply to neurologic care is limited. The American Academy of Neurology (AAN) identified the need for neurologists to develop measures of neurologic care and to establish a process to accomplish this. Objective: To adapt and test the feasibility of a process for independent development by the AAN of measures for neurologic conditions for national measurement programs. Methods: A process that has been used nationally for measure development was adapted for use by the AAN. Topics for measure development are chosen based upon national priorities, available evidence base from a systematic literature search, gaps in care, and the potential impact for quality improvement. A panel composed of subject matter and measure development methodology experts oversees the development of the measures. Recommendation statements and their corresponding level of evidence are reviewed and considered for development into draft candidate measures. The candidate measures are refined by the expert panel during a 30-day public comment period and by review by the American Medical Association for Current Procedural Terminology (CPT) II codes. All final AAN measures are approved by the AAN Board of Directors. Results: Parkinson disease (PD) was chosen for measure development. A review of the medical literature identified 258 relevant recommendation statements. A 28-member panel approved 10 quality measures for PD that included full specifications and CPT II codes. Conclusion: The AAN has adapted a measure development process that is suitable for national measurement programs and has demonstrated its capability to independently develop quality measures. GLOSSARY

Stochastic Models of Quality Control on Test Misgrading.

ERIC Educational Resources Information Center

Wang, Jianjun

Stochastic models are developed in this article to examine the rate of test misgrading in educational and psychological measurement. The estimation of inadvertent grading errors can serve as a basis for quality control in measurement. Limitations of traditional Poisson models have been reviewed to highlight the need to introduce new models using…

Candidate Quality Measures for Hand Surgery.

PubMed

2017-11-01

Quality measures are tools used by physicians, health care systems, and payers to evaluate performance, monitor the outcomes of interventions, and inform quality improvement efforts. A paucity of quality measures exist that address hand surgery care. We completed a RAND/UCLA (University of California Los Angeles) Delphi Appropriateness process with the goal of developing and evaluating candidate hand surgery quality measures to be used for national quality measure development efforts. A consortium of 9 academic upper limb surgeons completed a RAND/UCLA Delphi Appropriateness process to evaluate the importance, scientific acceptability, usability, and feasibility of 44 candidate quality measures. These addressed hand problems the panelists felt were most appropriate for quality measure development. Panelists rated the measures on an ordinal scale between 1 (definitely not valid) and 9 (definitely valid) in 2 rounds (preliminary round and final round) with an intervening face-to-face discussion. Ratings from 1 to 3 were considered not valid, 4 to 6 as equivocal or uncertain, and 7 to 9 as valid. If no more than 2 of the 9 ratings were outside the 3-point range that included the median (1-3, 4-6, or 7-9), the panelists were considered to be in agreement. If 3 or more of the panelists' ratings of a measure were within the 1 to 3 range and 3 or more ratings were in the 7 to 9 range, the panelists were considered to be in disagreement. There was agreement on 43% (19) of the measures as important, 27% (12) as scientifically sound, 48% (21) as usable, and 59% (26) as feasible to complete. Ten measures met all 4 of these criteria and were, therefore, considered valid measurements of quality. Quality measures that were developed address outcomes (patient-reported outcomes for assessment and improvement of function) and processes of care (utilization rates of imaging, antibiotics, occupational therapy, ultrasound, and operative treatment). The consortium developed 10

Standard procedures and quality-control practices for the U.S. Geological Survey National Field Quality Assurance Program from 1982 through 1993

USGS Publications Warehouse

Stanley, D.L.

1995-01-01

The U.S. Geological Survey operates the National Field Quality Assurance Program to provide quality- assurance reference samples to field personnel who make water-quality field measurements. The program monitors the accuracy and precision of pH, specific conductance, and alkalinity field measurements. This report documents the operational procedures and quality-control techniques used in operating the quality-assurance program.

Quality control and assurance for validation of DOS/I measurements

NASA Astrophysics Data System (ADS)

Cerussi, Albert; Durkin, Amanda; Kwong, Richard; Quang, Timothy; Hill, Brian; Tromberg, Bruce J.; MacKinnon, Nick; Mantulin, William W.

2010-02-01

Ongoing multi-center clinical trials are crucial for Biophotonics to gain acceptance in medical imaging. In these trials, quality control (QC) and assurance (QA) are key to success and provide "data insurance". Quality control and assurance deal with standardization, validation, and compliance of procedures, materials and instrumentation. Specifically, QC/QA involves systematic assessment of testing materials, instrumentation performance, standard operating procedures, data logging, analysis, and reporting. QC and QA are important for FDA accreditation and acceptance by the clinical community. Our Biophotonics research in the Network for Translational Research in Optical Imaging (NTROI) program for breast cancer characterization focuses on QA/QC issues primarily related to the broadband Diffuse Optical Spectroscopy and Imaging (DOS/I) instrumentation, because this is an emerging technology with limited standardized QC/QA in place. In the multi-center trial environment, we implement QA/QC procedures: 1. Standardize and validate calibration standards and procedures. (DOS/I technology requires both frequency domain and spectral calibration procedures using tissue simulating phantoms and reflectance standards, respectively.) 2. Standardize and validate data acquisition, processing and visualization (optimize instrument software-EZDOS; centralize data processing) 3. Monitor, catalog and maintain instrument performance (document performance; modularize maintenance; integrate new technology) 4. Standardize and coordinate trial data entry (from individual sites) into centralized database 5. Monitor, audit and communicate all research procedures (database, teleconferences, training sessions) between participants ensuring "calibration". This manuscript describes our ongoing efforts, successes and challenges implementing these strategies.

Quality and Control of Water Vapor Winds

NASA Technical Reports Server (NTRS)

Jedlovec, Gary J.; Atkinson, Robert J.

1996-01-01

Water vapor imagery from the geostationary satellites such as GOES, Meteosat, and GMS provides synoptic views of dynamical events on a continual basis. Because the imagery represents a non-linear combination of mid- and upper-tropospheric thermodynamic parameters (three-dimensional variations in temperature and humidity), video loops of these image products provide enlightening views of regional flow fields, the movement of tropical and extratropical storm systems, the transfer of moisture between hemispheres and from the tropics to the mid- latitudes, and the dominance of high pressure systems over particular regions of the Earth. Despite the obvious larger scale features, the water vapor imagery contains significant image variability down to the single 8 km GOES pixel. These features can be quantitatively identified and tracked from one time to the next using various image processing techniques. Merrill et al. (1991), Hayden and Schmidt (1992), and Laurent (1993) have documented the operational procedures and capabilities of NOAA and ESOC to produce cloud and water vapor winds. These techniques employ standard correlation and template matching approaches to wind tracking and use qualitative and quantitative procedures to eliminate bad wind vectors from the wind data set. Techniques have also been developed to improve the quality of the operational winds though robust editing procedures (Hayden and Veldon 1991). These quality and control approaches have limitations, are often subjective, and constrain wind variability to be consistent with model derived wind fields. This paper describes research focused on the refinement of objective quality and control parameters for water vapor wind vector data sets. New quality and control measures are developed and employed to provide a more robust wind data set for climate analysis, data assimilation studies, as well as operational weather forecasting. The parameters are applicable to cloud-tracked winds as well with minor

Process-based quality for thermal spray via feedback control

NASA Astrophysics Data System (ADS)

Dykhuizen, R. C.; Neiser, R. A.

2006-09-01

Quality control of a thermal spray system manufacturing process is difficult due to the many input variables that need to be controlled. Great care must be taken to ensure that the process remains constant to obtain a consistent quality of the parts. Control is greatly complicated by the fact that measurement of particle velocities and temperatures is a noisy stochastic process. This article illustrates the application of quality control concepts to a wire flame spray process. A central feature of the real-time control system is an automatic feedback control scheme that provides fine adjustments to ensure that uncontrolled variations are accommodated. It is shown how the control vectors can be constructed from simple process maps to independently control particle velocity and temperature. This control scheme is shown to perform well in a real production environment. We also demonstrate that slight variations in the feed wire curvature can greatly influence the process. Finally, the geometry of the spray system and sensor must remain constant for the best reproducibility.

Microbiological water methods: quality control measures for Federal Clean Water Act and Safe Drinking Water Act regulatory compliance.

PubMed

Root, Patsy; Hunt, Margo; Fjeld, Karla; Kundrat, Laurie

2014-01-01

Quality assurance (QA) and quality control (QC) data are required in order to have confidence in the results from analytical tests and the equipment used to produce those results. Some AOAC water methods include specific QA/QC procedures, frequencies, and acceptance criteria, but these are considered to be the minimum controls needed to perform a microbiological method successfully. Some regulatory programs, such as those at Code of Federal Regulations (CFR), Title 40, Part 136.7 for chemistry methods, require additional QA/QC measures beyond those listed in the method, which can also apply to microbiological methods. Essential QA/QC measures include sterility checks, reagent specificity and sensitivity checks, assessment of each analyst's capabilities, analysis of blind check samples, and evaluation of the presence of laboratory contamination and instrument calibration and checks. The details of these procedures, their performance frequency, and expected results are set out in this report as they apply to microbiological methods. The specific regulatory requirements of CFR Title 40 Part 136.7 for the Clean Water Act, the laboratory certification requirements of CFR Title 40 Part 141 for the Safe Drinking Water Act, and the International Organization for Standardization 17025 accreditation requirements under The NELAC Institute are also discussed.

Inhibitory Control Mediates the Association between Perceived Stress and Secure Relationship Quality.

PubMed

Herd, Toria; Li, Mengjiao; Maciejewski, Dominique; Lee, Jacob; Deater-Deckard, Kirby; King-Casas, Brooks; Kim-Spoon, Jungmeen

2018-01-01

Past research has demonstrated negative associations between exposure to stressors and quality of interpersonal relationships among children and adolescents. Nevertheless, underlying mechanisms of this association remain unclear. Chronic stress has been shown to disrupt prefrontal functioning in the brain, including inhibitory control abilities, and evidence is accumulating that inhibitory control may play an important role in secure interpersonal relationship quality, including peer problems and social competence. In this prospective longitudinal study, we examine whether changes in inhibitory control, measured at both behavioral and neural levels, mediate the association between stress and changes in secure relationship quality with parents and peers. The sample included 167 adolescents (53% males) who were first recruited at age 13 or 14 years and assessed annually three times. Adolescents' inhibitory control was measured by their behavioral performance and brain activities, and adolescents self-reported perceived stress levels and relationship quality with mothers, fathers, and peers. Results suggest that behavioral inhibitory control mediates the association between perceived stress and adolescent's secure relationship quality with their mothers and fathers, but not their peers. In contrast, given that stress was not significantly correlated with neural inhibitory control, we did not further test the mediation path. Our results highlight the role of inhibitory control as a process through which stressful life experiences are related to impaired secure relationship quality between adolescents and their mothers and fathers.

Inhibitory Control Mediates the Association between Perceived Stress and Secure Relationship Quality

PubMed Central

Herd, Toria; Li, Mengjiao; Maciejewski, Dominique; Lee, Jacob; Deater-Deckard, Kirby; King-Casas, Brooks; Kim-Spoon, Jungmeen

2018-01-01

Past research has demonstrated negative associations between exposure to stressors and quality of interpersonal relationships among children and adolescents. Nevertheless, underlying mechanisms of this association remain unclear. Chronic stress has been shown to disrupt prefrontal functioning in the brain, including inhibitory control abilities, and evidence is accumulating that inhibitory control may play an important role in secure interpersonal relationship quality, including peer problems and social competence. In this prospective longitudinal study, we examine whether changes in inhibitory control, measured at both behavioral and neural levels, mediate the association between stress and changes in secure relationship quality with parents and peers. The sample included 167 adolescents (53% males) who were first recruited at age 13 or 14 years and assessed annually three times. Adolescents’ inhibitory control was measured by their behavioral performance and brain activities, and adolescents self-reported perceived stress levels and relationship quality with mothers, fathers, and peers. Results suggest that behavioral inhibitory control mediates the association between perceived stress and adolescent’s secure relationship quality with their mothers and fathers, but not their peers. In contrast, given that stress was not significantly correlated with neural inhibitory control, we did not further test the mediation path. Our results highlight the role of inhibitory control as a process through which stressful life experiences are related to impaired secure relationship quality between adolescents and their mothers and fathers. PMID:29535664

Introducing Quality Control in the Chemistry Teaching Laboratory Using Control Charts

ERIC Educational Resources Information Center

Schazmann, Benjamin; Regan, Fiona; Ross, Mary; Diamond, Dermot; Paull, Brett

2009-01-01

Quality control (QC) measures are less prevalent in teaching laboratories than commercial settings possibly owing to a lack of commercial incentives or teaching resources. This article focuses on the use of QC assessment in the analytical techniques of high performance liquid chromatography (HPLC) and ultraviolet-visible spectroscopy (UV-vis) at…

SIMBAD quality-control

NASA Technical Reports Server (NTRS)

Lesteven, Soizick

1992-01-01

The astronomical database SIMBAD developed at the Centre de donnees astronomiques de Strasbourg presently contains 760,000 objects (stellar and non-stellar). It has the unique characteristic of being structured specifically for astronomical objects. All types of heterogeneous data (bibliographic references, measurements, and sets of identification) are connected with each object. The attributes that define quality of the database include the following. Reliability: cross-identification should not rely upon just exact values object coordinates. It also means that information attached to one simple object should be consistent. The existing data must be controlled in order to start with a reliable base and to cross-identify new data assuring the quality as data grows. Exhaustivity: delays between publication of new informations and their inclusion in the database should be as short as possible. The integrity of the database has to be maintained as data accumulates. Taking the amount of data into consideration and the rate of new data production, it is necessary to use automatic methods. One of the possibilities is to use multivariate data analysis. The factor-space is a n-dimensional relevancy space which is described by the n-axes representing a set of n subject matter headings; the words and phrases can be used to scale the axes and the documents are then a vector average of the terms within them. The application reported herein is based on the NASA-STI bibliographical database. The selected data concern astronomy, astrophysics, and space radiation (102,963 references from 1975 to 1991 included 8070 keywords). The F-space is built from this bibliographical data. By comparing the F-space position obtained from the NASA-STI keywords with the F-space position obtained from the SIMBAD references, the authors will be able to show whether it is possible to retrieve information with a restricted set of words only. If the comparison is valid, this will be a way to enter

Measurement Matters: Assessing Personal Qualities Other Than Cognitive Ability for Educational Purposes

PubMed Central

Duckworth, Angela L.; Yeager, David Scott

2016-01-01

There has been perennial interest in personal qualities other than cognitive ability that determine success, including self-control, grit, growth mindset, and many others. Attempts to measure such qualities for the purposes of educational policy and practice, however, are more recent. In this article, we identify serious challenges to doing so. We first address confusion over terminology, including the descriptor “non-cognitive.” We conclude that debate over the optimal name for this broad category of personal qualities obscures substantial agreement about the specific attributes worth measuring. Next, we discuss advantages and limitations of different measures. In particular, we compare self-report questionnaires, teacher-report questionnaires, and performance tasks, using self-control as an illustrative case study to make the general point that each approach is imperfect in its own way. Finally, we discuss how each measure’s imperfections can affect its suitability for program evaluation, accountability, individual diagnosis, and practice improvement. For example, we do not believe any available measure is suitable for between-school accountability judgments. In addition to urging caution among policymakers and practitioners, we highlight medium-term innovations that may make measures of these personal qualities more suitable for educational purposes. PMID:27134288

40 CFR 75.21 - Quality assurance and quality control requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Quality assurance and quality control... PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Operation and Maintenance Requirements § 75.21 Quality assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner or...

Role of Protein Quality Control Failure in Alcoholic Hepatitis Pathogenesis.

PubMed

French, Samuel W; Masouminia, Maryam; Samadzadeh, Sara; Tillman, Brittany C; Mendoza, Alejandro; French, Barbara A

2017-02-08

The mechanisms of protein quality control in hepatocytes in cases of alcoholic hepatitis (AH) including ufmylation, FAT10ylation, metacaspase 1 (Mca1), ERAD (endoplasmic reticulum-associated degradation), JUNQ (juxta nuclear quality control), IPOD (insoluble protein deposit) autophagocytosis, and ER stress are reviewed. The Mallory-Denk body (MDB) formation develops in the hepatocytes in alcoholic hepatitis as a consequence of the failure of these protein quality control mechanisms to remove misfolded and damaged proteins and to prevent MDB aggresome formation within the cytoplasm of hepatocytes. The proteins involved in the quality control pathways are identified, quantitated, and visualized by immunofluorescent antibody staining of liver biopsies from patients with AH. Quantification of the proteins are achieved by measuring the fluorescent intensity using a morphometric system. Ufmylation and FAT10ylation pathways were downregulated, Mca1 pathways were upregulated, autophagocytosis was upregulated, and ER stress PERK (protein kinase RNA-like endoplasmic reticulum kinase) and CHOP (CCAAT/enhancer-binding protein homologous protein) mechanisms were upregulated. Despite the upregulation of several pathways of protein quality control, aggresomes (MDBs) still formed in the hepatocytes in AH. The pathogenesis of AH is due to the failure of protein quality control, which causes balloon-cell change with MDB formation and ER stress.

Measurement and Control of the Variability of Scanning Pressure Transducer Measurements

NASA Technical Reports Server (NTRS)

Kuhl, David D.; Everhart, Joel L.; Hallissy, James B.

2003-01-01

This paper describes the new wall pressure measurement system and data-quality monitoring software installed at 14x22 Ft subsonic tunnel at the NASA Langley Research Center. The monitoring software was developed to enable measurement and control of the variability of the reference pressures and approximately 400 tunnel wall pressure measurements. Variability of the system, based upon data acquired over a year of wind tunnel tests and calibrations, is presented. The level of variation of the wall pressure measurements is shown to be predictable.

Network-based production quality control

NASA Astrophysics Data System (ADS)

Kwon, Yongjin; Tseng, Bill; Chiou, Richard

2007-09-01

This study investigates the feasibility of remote quality control using a host of advanced automation equipment with Internet accessibility. Recent emphasis on product quality and reduction of waste stems from the dynamic, globalized and customer-driven market, which brings opportunities and threats to companies, depending on the response speed and production strategies. The current trends in industry also include a wide spread of distributed manufacturing systems, where design, production, and management facilities are geographically dispersed. This situation mandates not only the accessibility to remotely located production equipment for monitoring and control, but efficient means of responding to changing environment to counter process variations and diverse customer demands. To compete under such an environment, companies are striving to achieve 100%, sensor-based, automated inspection for zero-defect manufacturing. In this study, the Internet-based quality control scheme is referred to as "E-Quality for Manufacturing" or "EQM" for short. By its definition, EQM refers to a holistic approach to design and to embed efficient quality control functions in the context of network integrated manufacturing systems. Such system let designers located far away from the production facility to monitor, control and adjust the quality inspection processes as production design evolves.

A computerized system to measure and predict air quality for emission control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crooks, G.; Ciccone, A.; Frattolillo, P.

1997-12-31

A Supplementary Emission Control (SEC) system has been developed on behalf of the Association Industrielle de l`Est de Montreal (AIEM). The objective of the SEC is to avoid exceedences of the Montreal Urban Community (MUC) 24 hour ambient Air Quality Standard (AQS) for sulphur dioxide in the industrial East Montreal area. The SEC system is comprised of: 3 continuous SO{sub 2} monitoring stations with data loggers and remote communications; a meteorological tower with data logger and modem for acquiring local meteorology; communications with Environment Canada to download meteorological forecast data; a polling PC for data retrieval; and Windows NT basedmore » software running on the AIEM computer server. The SEC software utilizes relational databases to store and maintain measured SO{sub 2} concentration data, emission data, as well as observed and forecast meteorological data. The SEC system automatically executes a numerical dispersion model to forecast SO{sub 2} concentrations up to six hours in the future. Based on measured SO{sub 2} concentrations at the monitoring stations and the six hour forecast concentrations, the system determines if local sources should reduce their emission levels to avoid potential exceedences of the AQS. The SEC system also includes a Graphical User Interface (GUI) for user access to the system. The SEC system and software are described, and the accuracy of the system at forecasting SO{sub 2} concentrations is examined.« less

40 CFR 51.359 - Quality control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 2 2014-07-01 2014-07-01 false Quality control. 51.359 Section 51.359 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS REQUIREMENTS FOR... to assure test accuracy. Computer control of quality assurance checks and quality control charts...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

The importance of quality assurance/quality control of diagnostics to increase the confidence in global foot-and-mouth disease control.

PubMed

De Clercq, K; Goris, N; Barnett, P V; MacKay, D K

2008-01-01

The last decade international trade in animals and animal products was liberated and confidence in this global trade can increase only if appropriate control measures are applied. As foot-and-mouth disease (FMD) diagnostics will play an essential role in this respect, the Food and Agriculture Organization European Commission for the Control of Foot-and-Mouth Disease (EUFMD) co-ordinates, in collaboration with the European Commission, several programmes to increase the quality of FMD diagnostics. A quality assurance (QA) system is deemed essential for laboratories involved in certifying absence of FMDV or antibodies against the virus. Therefore, laboratories are encouraged to validate their diagnostic tests fully and to install a continuous quality control (QC) monitoring system. Knowledge of performance characteristics of diagnostics is essential to interpret results correctly and to calculate sample rates in regional surveillance campaigns. Different aspects of QA/QC of classical and new FMD virological and serological diagnostics are discussed in respect to the EU FMD directive (2003/85/EC). We recommended accepting trade certificates only from laboratories participating in international proficiency testing on a regular basis.

7 CFR 930.44 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

7 CFR 930.44 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

7 CFR 930.44 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

7 CFR 930.44 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

Cumulative uncertainty in measured streamflow and water quality data for small watersheds

USGS Publications Warehouse

Harmel, R.D.; Cooper, R.J.; Slade, R.M.; Haney, R.L.; Arnold, J.G.

2006-01-01

The scientific community has not established an adequate understanding of the uncertainty inherent in measured water quality data, which is introduced by four procedural categories: streamflow measurement, sample collection, sample preservation/storage, and laboratory analysis. Although previous research has produced valuable information on relative differences in procedures within these categories, little information is available that compares the procedural categories or presents the cumulative uncertainty in resulting water quality data. As a result, quality control emphasis is often misdirected, and data uncertainty is typically either ignored or accounted for with an arbitrary margin of safety. Faced with the need for scientifically defensible estimates of data uncertainty to support water resource management, the objectives of this research were to: (1) compile selected published information on uncertainty related to measured streamflow and water quality data for small watersheds, (2) use a root mean square error propagation method to compare the uncertainty introduced by each procedural category, and (3) use the error propagation method to determine the cumulative probable uncertainty in measured streamflow, sediment, and nutrient data. Best case, typical, and worst case "data quality" scenarios were examined. Averaged across all constituents, the calculated cumulative probable uncertainty (??%) contributed under typical scenarios ranged from 6% to 19% for streamflow measurement, from 4% to 48% for sample collection, from 2% to 16% for sample preservation/storage, and from 5% to 21% for laboratory analysis. Under typical conditions, errors in storm loads ranged from 8% to 104% for dissolved nutrients, from 8% to 110% for total N and P, and from 7% to 53% for TSS. Results indicated that uncertainty can increase substantially under poor measurement conditions and limited quality control effort. This research provides introductory scientific estimates of

A real time quality control application for animal production by image processing.

PubMed

Sungur, Cemil; Özkan, Halil

2015-11-01

Standards of hygiene and health are of major importance in food production, and quality control has become obligatory in this field. Thanks to rapidly developing technologies, it is now possible for automatic and safe quality control of food production. For this purpose, image-processing-based quality control systems used in industrial applications are being employed to analyze the quality of food products. In this study, quality control of chicken (Gallus domesticus) eggs was achieved using a real time image-processing technique. In order to execute the quality control processes, a conveying mechanism was used. Eggs passing on a conveyor belt were continuously photographed in real time by cameras located above the belt. The images obtained were processed by various methods and techniques. Using digital instrumentation, the volume of the eggs was measured, broken/cracked eggs were separated and dirty eggs were determined. In accordance with international standards for classifying the quality of eggs, the class of separated eggs was determined through a fuzzy implication model. According to tests carried out on thousands of eggs, a quality control process with an accuracy of 98% was possible. © 2014 Society of Chemical Industry.

Quality control of fireproof coatings for reinforced concrete structures

NASA Astrophysics Data System (ADS)

Gravit, Marina; Dmitriev, Ivan; Ishkov, Alexander

2017-10-01

The article analyzes methods of quality inspection of fireproof coatings (work flow, measuring, laboratory, etc.). In modern construction there is a problem of lack of distinct monitoring for the fire protection testing. There is a description of this testing for reinforced concrete structures. The article shows the results of calculation quality control of hatches as an example of fireproof coating for reinforced concrete structures.

14 CFR 21.139 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Quality control. 21.139 Section 21.139... PROCEDURES FOR PRODUCTS AND PARTS Production Certificates § 21.139 Quality control. The applicant must show that he has established and can maintain a quality control system for any product, for which he...

33 CFR 385.21 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Quality control. 385.21 Section... Processes § 385.21 Quality control. (a) The Corps of Engineers and the non-Federal sponsor shall prepare a quality control plan, in accordance with applicable Corps of Engineers regulations, for each product that...

14 CFR 21.139 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Quality control. 21.139 Section 21.139... PROCEDURES FOR PRODUCTS AND PARTS Production Certificates § 21.139 Quality control. The applicant must show that he has established and can maintain a quality control system for any product, for which he...

33 CFR 385.21 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Quality control. 385.21 Section... Processes § 385.21 Quality control. (a) The Corps of Engineers and the non-Federal sponsor shall prepare a quality control plan, in accordance with applicable Corps of Engineers regulations, for each product that...

33 CFR 385.21 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Quality control. 385.21 Section... Processes § 385.21 Quality control. (a) The Corps of Engineers and the non-Federal sponsor shall prepare a quality control plan, in accordance with applicable Corps of Engineers regulations, for each product that...

Quality control in public participation assessments of water quality: the OPAL Water Survey.

PubMed

Rose, N L; Turner, S D; Goldsmith, B; Gosling, L; Davidson, T A

2016-07-22

Public participation in scientific data collection is a rapidly expanding field. In water quality surveys, the involvement of the public, usually as trained volunteers, generally includes the identification of aquatic invertebrates to a broad taxonomic level. However, quality assurance is often not addressed and remains a key concern for the acceptance of publicly-generated water quality data. The Open Air Laboratories (OPAL) Water Survey, launched in May 2010, aimed to encourage interest and participation in water science by developing a 'low-barrier-to-entry' water quality survey. During 2010, over 3000 participant-selected lakes and ponds were surveyed making this the largest public participation lake and pond survey undertaken to date in the UK. But the OPAL approach of using untrained volunteers and largely anonymous data submission exacerbates quality control concerns. A number of approaches were used in order to address data quality issues including: sensitivity analysis to determine differences due to operator, sampling effort and duration; direct comparisons of identification between participants and experienced scientists; the use of a self-assessment identification quiz; the use of multiple participant surveys to assess data variability at single sites over short periods of time; comparison of survey techniques with other measurement variables and with other metrics generally considered more accurate. These quality control approaches were then used to screen the OPAL Water Survey data to generate a more robust dataset. The OPAL Water Survey results provide a regional and national assessment of water quality as well as a first national picture of water clarity (as suspended solids concentrations). Less than 10 % of lakes and ponds surveyed were 'poor' quality while 26.8 % were in the highest water quality band. It is likely that there will always be a question mark over untrained volunteer generated data simply because quality assurance is uncertain

40 CFR 136.7 - Quality assurance and quality control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality control elements, where applicable, into the laboratory's documented standard operating procedure... quality control elements must be clearly documented in the written standard operating procedure for each... Methods contains QA/QC procedures in the Part 1000 section of the Standard Methods Compendium. The...

40 CFR 136.7 - Quality assurance and quality control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality control elements, where applicable, into the laboratory's documented standard operating procedure... quality control elements must be clearly documented in the written standard operating procedure for each... Methods contains QA/QC procedures in the Part 1000 section of the Standard Methods Compendium. The...

40 CFR 136.7 - Quality assurance and quality control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality control elements, where applicable, into the laboratory's documented standard operating procedure... quality control elements must be clearly documented in the written standard operating procedure for each... Methods contains QA/QC procedures in the Part 1000 section of the Standard Methods Compendium. The...

Quality measures for nurse practitioner practice evaluation.

PubMed

Kleinpell, Ruth; Kapu, April N

2017-08-01

Evaluating the impact of nurse practitioner (NP) practice has become a priority area of focus for demonstrating outcomes. A number of quality measures are available to enable practice-specific evaluation of NP roles and initiatives. This article reviews sources of quality measures that can be used to facilitate quantifying the outcomes of NP practice as part of an overall evaluation agenda. National resources and published literature on NP quality measures were reviewed. Various resources and toolkits exist to assist NPs in identifying outcomes of practice using quality measures. The need to demonstrate outcomes of NP practice remains an ongoing priority area regardless of the clinical practice setting. A variety of sources of quality measures exist that can be used to showcase the effect of NP care. The use of quality measures can be effectively integrated into evaluation of NP role and NP-directed initiatives to demonstrate impact, and enhance the conduct of an NP outcomes assessment. The use of organizational, NP-specific, and national-related quality measures can help to showcase how NP care improves the quality, safety, and costs of health care. ©2017 American Association of Nurse Practitioners.

Impact of dose calibrators quality control programme in Argentina

NASA Astrophysics Data System (ADS)

Furnari, J. C.; de Cabrejas, M. L.; del C. Rotta, M.; Iglicki, F. A.; Milá, M. I.; Magnavacca, C.; Dima, J. C.; Rodríguez Pasqués, R. H.

1992-02-01

The national Quality Control (QC) programme for radionuclide calibrators started 12 years ago. Accuracy and the implementation of a QC programme were evaluated over all these years at 95 nuclear medicine laboratories where dose calibrators were in use. During all that time, the Metrology Group of CNEA has distributed 137Cs sealed sources to check stability and has been performing periodic "checking rounds" and postal surveys using unknown samples (external quality control). An account of the results of both methods is presented. At present, more of 65% of the dose calibrators measure activities with an error less than 10%.

Continuing Medical Education Improves Gastroenterologists' Compliance with Inflammatory Bowel Disease Quality Measures.

PubMed

Sapir, Tamar; Moreo, Kathleen; Carter, Jeffrey D; Greene, Laurence; Patel, Barry; Higgins, Peter D R

2016-07-01

Low rates of compliance with quality measures for inflammatory bowel disease (IBD) have been reported for US gastroenterologists. We assessed the influence of quality improvement (QI) education on compliance with physician quality reporting system (PQRS) measures for IBD and measures related to National Quality Strategy (NQS) priorities. Forty community-based gastroenterologists participated in the QI study; 20 were assigned to educational intervention and control groups, respectively. At baseline, randomly selected charts of patients with moderate-to-severe ulcerative colitis were retrospectively reviewed for the gastroenterologists' performance of 8 PQRS IBD measures and 4 NQS-related measures. The intervention group participated in a series of accredited continuing medical education (CME) activities focusing on QI. Follow-up chart reviews were conducted 6 months after the CME activities. Independent t tests were conducted to compare between-group differences in baseline-to-follow-up rates of documented compliance with each measure. The analysis included 299 baseline charts and 300 follow-up charts. The intervention group had significantly greater magnitudes of improvement than the control group for the following measures: assessment of IBD type, location, and activity (+14 %, p = 0.009); influenza vaccination (+13 %, p = 0.025); pneumococcal vaccination (+20 %, p = 0.003); testing for latent tuberculosis before anti-TNF-α therapy (+10 %, p = 0.028); assessment of hepatitis B virus status before anti-TNF-α therapy (+9 %, p = 0.010); assessment of side effects (+17 %, p = 0.048), and counseling patients about cancer risks (+13 %, p = 0.013). QI-focused CME improves community-based gastroenterologists' compliance with IBD quality measures and measures aligned with NQS priorities.

Application of video-cameras for quality control and sampling optimisation of hydrological and erosion measurements in a catchment

NASA Astrophysics Data System (ADS)

Lora-Millán, Julio S.; Taguas, Encarnacion V.; Gomez, Jose A.; Perez, Rafael

2014-05-01

Long term soil erosion studies imply substantial efforts, particularly when there is the need to maintain continuous measurements. There are high costs associated to maintenance of field equipment keeping and quality control of data collection. Energy supply and/or electronic failures, vandalism and burglary are common causes of gaps in datasets, reducing their reach in many cases. In this work, a system of three video-cameras, a recorder and a transmission modem (3G technology) has been set up in a gauging station where rainfall, runoff flow and sediment concentration are monitored. The gauging station is located in the outlet of an olive orchard catchment of 6.4 ha. Rainfall is measured with one automatic raingauge that records intensity at one minute intervals. The discharge is measured by a flume of critical flow depth, where the water is recorded by an ultrasonic sensor. When the water level rises to a predetermined level, the automatic sampler turns on and fills a bottle at different intervals according to a program depending on the antecedent precipitation. A data logger controls the instruments' functions and records the data. The purpose of the video-camera system is to improve the quality of the dataset by i) the visual analysis of the measurement conditions of flow into the flume; ii) the optimisation of the sampling programs. The cameras are positioned to record the flow at the approximation and the gorge of the flume. In order to contrast the values of ultrasonic sensor, there is a third camera recording the flow level close to a measure tape. This system is activated when the ultrasonic sensor detects a height threshold, equivalent to an electric intensity level. Thus, only when there is enough flow, video-cameras record the event. This simplifies post-processing and reduces the cost of download of recordings. The preliminary contrast analysis will be presented as well as the main improvements in the sample program.

Understanding Consumer Perceptions and Awareness of Hospital-Based Maternity Care Quality Measures.

PubMed

Maurer, Maureen; Firminger, Kirsten; Dardess, Pam; Ikeler, Kourtney; Sofaer, Shoshanna; Carman, Kristin L

2016-06-01

To explore factors that may influence use of comparative public reports for hospital maternity care. Four focus groups conducted in 2013 with 41 women and preintervention survey data collected in 2014 to 2015 from 245 pregnant women in North Carolina. As part of a larger randomized controlled trial, we conducted qualitative formative research to develop an intervention that will be evaluated through pre- and postintervention surveys. Analysis of focus group transcripts examined participants' perceptions of high-quality maternity care and the importance of different quality measures. Quantitative analysis included descriptive results of the preintervention survey and subgroup analyses to examine the impact of race, education, and being a first-time mom on outcomes. When describing high-quality maternity care, participants focused on interactions with providers, including respect for preferences and communication. The importance of quality measures was influenced by the extent to which they focused on babies' health, were perceived as the hospital's responsibility, and were perceived as representing "standard care." At baseline, 28 percent of survey respondents had used quality information to choose a hospital. Survey respondents were more aware of some quality measures (e.g., breastfeeding support) than others (e.g., episiotomy rates). Public reporting efforts could help increase relevance of maternity care quality measures by creating measures that reflect women's concerns, clearly explaining the hospital's role in supporting quality care, and showing how available quality measures can inform decisions about childbirth. © Health Research and Educational Trust.

[Designing and implementation of a web-based quality monitoring system for plasma glucose measurement in multicenter population study].

PubMed

Liu, Yong; Wang, Limin; Pang, Richard; Mo, Nanxun; Hu, Yan; Deng, Qian; Hu, Zhaohui

2015-05-01

The aim of this paper is to describe the designing and implementation of a web-based plasma glucose measurement quality monitoring system to assess the analytical quality of plasma glucose measurements in multicenter population study and provide evidence for the future studies. In the chronic non-communicable disease and related factor surveillance in China, a web based quality monitoring system for plasma glucose measurement was established to conduct evaluation on plasma glucose monitoring quality and effectiveness in 302 surveillance centers, including quality control data entry, transmission and feedback. The majority of the surveillance centers met the quality requirements and passed the evaluation of reproducibility and precision of plasma glucose measurement, only a few centers required intensive training and re-assessment. In order to ensure the completeness and reliability of plasma glucose measurement in the surveillance centers, the establishment of web-based plasma glucose measurement quality control system can facilitate the identification of the qualified surveillance centers and evaluation of plasma glucose measurement quality in different regions. Communication and training are important in ensuring plasma glucose measurement quality. It is necessary to further improve this web-based plasma glucose measurement quality monitoring system in the future to reduce the method specific plasma glucose measurement bias.

QUALITY CONTROL OF PHARMACEUTICALS.

PubMed

LEVI, L; WALKER, G C; PUGSLEY, L I

1964-10-10

Quality control is an essential operation of the pharmaceutical industry. Drugs must be marketed as safe and therapeutically active formulations whose performance is consistent and predictable. New and better medicinal agents are being produced at an accelerated rate. At the same time more exacting and sophisticated analytical methods are being developed for their evaluation. Requirements governing the quality control of pharmaceuticals in accordance with the Canadian Food and Drugs Act are cited and discussed.

7 CFR 58.928 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be...

Cellular-enabled water quality measurements

NASA Astrophysics Data System (ADS)

Zhao, Y.; Kerkez, B.

2013-12-01

While the past decade has seen significant improvements in our ability to measure nutrients and other water quality parameters, the use of these sensors has yet to gain traction due to their costprohibitive nature and deployment expertise required on the part of researchers. Furthermore, an extra burden is incurred when real-time data access becomes an experimental requirement. We present an open-source hardware design to facilitate the real-time, low-cost, and robust measurements of water quality across large urbanized areas. Our hardware platform interfaces an embedded, vastly configurable, high-precision, ultra-low power measurement system, with a low-power cellular module. Each sensor station is configured with an IP address, permitting reliable streaming of sensor data to off-site locations as measurements are made. We discuss the role of high-quality hardware components during extreme event scenarios, and present preliminary performance metrics that validate the ability of the platform to provide streaming access to sensor measurements.

Expert database system for quality control

NASA Astrophysics Data System (ADS)

Wang, Anne J.; Li, Zhi-Cheng

1993-09-01

There are more competitors today. Markets are not homogeneous they are fragmented into increasingly focused niches requiring greater flexibility in the product mix shorter manufacturing production runs and above allhigher quality. In this paper the author identified a real-time expert system as a way to improve plantwide quality management. The quality control expert database system (QCEDS) by integrating knowledge of experts in operations quality management and computer systems use all information relevant to quality managementfacts as well as rulesto determine if a product meets quality standards. Keywords: expert system quality control data base

Measuring Inpatient Rehabilitation Facility Quality of Care: Discharge Self-Care Functional Status Quality Measure.

PubMed

Pardasaney, Poonam K; Deutsch, Anne; Iriondo-Perez, Jeniffer; Ingber, Melvin J; McMullen, Tara

2018-06-01

To describe the calculation and psychometric properties of the discharge self-care functional status quality measure implemented in the Centers for Medicare & Medicaid Services' (CMS) Inpatient Rehabilitation Facility (IRF) Quality Reporting Program on October 1, 2016. Medicare fee-for-service (FFS) patients from 38 IRFs that participated in the CMS Post-Acute Care Payment Reform Demonstration were included in this cohort study. Data came from the Continuity Assessment Record and Evaluation Item Set, IRF-Patient Assessment Instrument, and Medicare claims. For each patient, we calculated an expected discharge self-care score, risk-adjusted for demographic and baseline clinical characteristics. The performance score of each IRF equaled the percentage of patient stays where the observed discharge self-care score met or exceeded the expected score. We assessed the measure's discriminatory ability across IRFs and reliability. IRFs. Medicare FFS patients aged ≥21 years (N=4769). Not applicable. Facility-level discharge self-care quality measure performance score. A total of 4769 patient stays were included; 57% of stays were in women, and 12.1% were in patients aged <65 years. Stroke was the most common diagnosis (21.8%). The mean±SD performance score was 55.1%±16.6% (range, 25.8%-100%). About 54% of IRFs had scores significantly different from the percentage of stays that met or exceeded the expected discharge self-care score in the overall demonstration sample. The quality measure showed strong reliability, with intraclass correlation coefficients of .91. The discharge self-care quality measure showed strong discriminatory ability and reliability, representing an important initial step in evaluation of IRF self-care outcomes. A wide range in performance scores suggested a gap in quality of care across IRFs. Future work should include testing the measure with nationwide data from all IRFs. Published by Elsevier Inc.

Qualities of Sore Throat Index (QuaSTI): measuring descriptors of sore throat in a randomized, placebo-controlled trial.

PubMed

Schachtel, Bernard; Shephard, Adrian; Schachtel, Emily; Lorton, Mary Beth; Shea, Tim; Aspley, Sue

2018-03-01

Patients with pharyngitis often describe various sensory, affective and evaluative pain qualities. Using an 11-word/phrase index, the Qualities of Sore Throat Index (QuaSTI), we characterized throat symptoms and evaluated changes in a randomized controlled trial (NCT01986361). Patients received a single flurbiprofen 8.75 mg (n = 101) or placebo (n = 21) lozenge and rated throat soreness at baseline and regular intervals over 3 h, and the QuaSTI at baseline, 1, 2 and 3 h post-treatment. The QuaSTI distinguished active drug from placebo and detected clinically important (≥2-point) changes over 3 h. Mean change from baseline over 3 h was significantly greater for flurbiprofen (154%) than placebo (p < 0.05). The QuaSTI is a sensitive instrument for measuring therapeutic effects in patients with pharyngitis.

Do prominent quality measurement surveys capture the concerns of persons with disability?

PubMed

Iezzoni, Lisa I; Marsella, Sarah A; Lopinsky, Tiffany; Heaphy, Dennis; Warsett, Kimberley S

2017-04-01

Demonstration programs nationwide aim to control costs and improve care for people dually-eligible for Medicare and Medicaid, including many persons with disability. Ensuring these initiatives maintain or improve care quality requires comprehensive evaluation of quality of care. To examine whether the common quality measures being used to evaluate the Massachusetts One Care duals demonstration program comprehensively address the concerns of persons with disability. Drawing upon existing conceptual frameworks, we developed a model of interrelationships of personal, health care, and environmental factors for achieving wellness for persons with disability. Based on this model, we specified a scheme to code individual quality measurement items and coded the items contained in 12 measures being used to assess Massachusetts One Care, which exclusively enrolls non-elderly adults with disability. Across these 12 measures, we assigned 376 codes to 302 items; some items received two codes. Taken together, the 12 measures contain items addressing most factors in our conceptual model that affect health care quality for persons with disability, including long-term services and supports. Some important gaps exist. No items examine sexual or reproductive health care, peer support, housing security, disability stigmatization, and specific services obtained outside the home like adult day care. Certain key concepts are covered only by a single or several of the 12 quality measures. Common quality metrics cover most - although not all-health care quality concerns of persons with disability. However, multiple different quality measures are required for this comprehensive coverage, raising questions about respondent burden. Copyright © 2017 Elsevier Inc. All rights reserved.

Quality Measures for Hospice and Palliative Care: Piloting the PEACE Measures

PubMed Central

Rokoske, Franziska S.; Durham, Danielle; Cagle, John G.; Hanson, Laura C.

2014-01-01

Abstract Background: The Carolinas Center for Medical Excellence launched the PEACE project in 2006, under contract with the Centers for Medicare & Medicaid Services (CMS), to identify, develop, and pilot test quality measures for hospice and palliative care programs. Objectives: The project collected pilot data to test the usability and feasibility of potential quality measures and data collection processes for hospice and palliative care programs. Settings/subjects: Twenty-two hospices participating in a national Quality Improvement Collaborative (QIC) submitted data from 367 chart reviews for pain care and 45 chart reviews for nausea care. Fourteen additional hospices completed a one-time data submission of 126 chart reviews on 60 potential patient-level quality measures across eight domains of care and an organizational assessment evaluating structure and processes of care. Design: Usability was assessed by examining the range, variability and size of the populations targeted by each quality measure. Feasibility was assessed during the second pilot study by surveying data abstractors about the abstraction process and examining the rates of missing data. The impact of data collection processes was assessed by comparing results obtained using different processes. Results: Measures shown to be both usable and feasible included: screening for physical symptoms on admission and documentation of treatment preferences. Methods of data collection and measure construction appear to influence observed rates of quality of care. Conclusions: We successfully identified quality measures with potential for use in hospices and palliative care programs. Future research is needed to understand whether these measures are sensitive to quality improvement interventions. PMID:24921162

7 CFR 58.335 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.335 Section 58.335... Procedures § 58.335 Quality control tests. All milk, cream and related products are subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow...

[Quality measurement using administrative data in mandatory quality assurance].

PubMed

Heller, Günther; Szecsenyi, Joachim; Willms, Gerald; Broge, Björn

2014-01-01

For several years, the use of administrative data in mandatory quality measurement has been requested by several stakeholders in Germany. Main advantages of using administrative data include the reduction of documentary expenditures and the possibility to perform longitudinal quality analyses across different healthcare units. After a short introduction, a brief overview of the current use of administrative data for mandatory quality assurance as well as current developments is given, which will then be further exemplified by decubital ulcer prophylaxis. By using administrative data coding expenditures in this clinical area could be reduced by nine million data fields. At the same time the population analysed was expanded resulting in a more than tenfold increase in potentially quality-relevant events. Finally, perspectives, further developments, possibilities as well as limits of quality measurement with administrative data are discussed. Copyright © 2014. Published by Elsevier GmbH.

Quality Control of Pharmaceuticals

PubMed Central

Levi, Leo; Walker, George C.; Pugsley, L. I.

1964-01-01

Quality control is an essential operation of the pharmaceutical industry. Drugs must be marketed as safe and therapeutically active formulations whose performance is consistent and predictable. New and better medicinal agents are being produced at an accelerated rate. At the same time more exacting and sophisticated analytical methods are being developed for their evaluation. Requirements governing the quality control of pharmaceuticals in accordance with the Canadian Food and Drugs Act are cited and discussed. PMID:14199105

Rural relevant quality measures for critical access hospitals.

PubMed

Casey, Michelle M; Moscovice, Ira; Klingner, Jill; Prasad, Shailendra

2013-01-01

To identify current and future relevant quality measures for Critical Access Hospitals (CAHs). Three criteria (patient volume, internal usefulness for quality improvement, and external usefulness for public reporting and payment reform) were used to analyze quality measures for their relevance for CAHs. A 6-member panel with expertise in rural hospital quality measurement and improvement provided input regarding the final measure selection. The relevant quality measures for CAHs include measures that are ready for reporting now and measures that need specifications to be finalized and/or a data reporting mechanism to be established. They include inpatient measures for specific medical conditions, global measures that address appropriate care across multiple medical conditions, and Emergency Department measures. All CAHs should publicly report on relevant quality measures. Acceptance of a single consolidated set of quality measures with common specifications for CAHs by all entities involved in regulation, accreditation, and payment; a phased process to implement the relevant measures; and the provision of technical assistance would help CAHs meet the challenge of reporting. © 2012 National Rural Health Association.

The measurement of carbon monoxide and methane in the national capital air quality control region. III - Correlation interferometer results

NASA Technical Reports Server (NTRS)

Goldstein, H. W.; Bortner, M. H.; Grenda, R. N.; Dick, R.; Lebel, P. J.; Lamontagne, R. A.

1976-01-01

Two types of experiments were performed with a correlation interferometer on-board a Bell Jet Ranger 206 Helicopter. The first consisted of simultaneous ground- and air-truth measurements as the instrumented helicopter passed over the Cheverly site. The second consisted of several measurement flights in and around the national capital air quality control region (Washington, D.C.). The correlation interferometer data, the infrared Fourier spectrometer data, and the integrated altitude sampling data showed agreement within the errors of the individual measurements. High values for CO were found from the D.C. flight data to be reproducible and concentrated in areas of stop-and-go traffic. It is concluded, that pollutants at low altitudes are detectable from an air-borne platform by remote correlation interferometry and that the correlation interferometer measurements agree with ground- and air-truth data.

Sap flow sensors: construction, quality control and comparison.

PubMed

Davis, Tyler W; Kuo, Chen-Min; Liang, Xu; Yu, Pao-Shan

2012-01-01

This work provides a design for two types of sensors, based on the thermal dissipation and heat ratio methods of sap flow calculation, for moderate to large scale deployments for the purpose of monitoring tree transpiration. These designs include a procedure for making these sensors, a quality control method for the final products, and a complete list of components with vendors and pricing information. Both sensor designs were field tested alongside a commercial sap flow sensor to assess their performance and show the importance for quality controlling the sensor outputs. Results show that for roughly 2% of the cost of commercial sensors, self-made sap flow sensors can provide acceptable estimates of the sap flow measurements compared to the commercial sensors.

Perceived parent-child relational qualities and parental behavioral and psychological control in Chinese adolescents in Hong Kong.

PubMed

Shek, Daniel T L

2006-01-01

Chinese secondary school students (N = 3,017) were asked to respond to instruments measuring their perceived parent-child relational qualities (parental trust of the child, child's trust of parents, child's readiness to communicate with parents, and child's satisfaction with parental control), parental behavioral control (including indicators of knowledge, expectation, monitoring, discipline, and demandingness), and parental psychological control. Results showed that parental trust of the child and child's trust of parents were positively related to child's readiness to communicate with the parents and satisfaction with parental control. While parental trust of the child and child's trust of parents were basically negatively related to different aspects of behavioral control (except parental knowledge), readiness to communicate with the parents and satisfaction with parental control were positively associated with parental control. Parent-child relational quality measures were negatively related to psychological control. Relative to measures of parental behavioral control, parental psychological control was a stronger predictor of parent-child relational qualities. The present findings clarify the parent-child relational quality correlates of parental behavioral and psychological control.

30 CFR 28.31 - Quality control plans; contents.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality control plans; contents. 28.31 Section... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.31 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the management of quality, including: (1...

[Highly quality-controlled radiation therapy].

PubMed

Shirato, Hiroki

2005-04-01

Advanced radiation therapy for intracranial disease has focused on set-up accuracy for the past 15 years. However, quality control in the prescribed dose is actually as important as the tumor set-up in radiation therapy. Because of the complexity of the three-dimensional radiation treatment planning system in recent years, the highly quality-controlled prescription of the dose has now been reappraised as the mainstream to improve the treatment outcome of radiation therapy for intracranial disease. The Japanese Committee for Quality Control of Radiation Therapy has developed fundamental requirements such as a QC committee in each hospital, a medical physicist, dosimetrists (QC members), and an external audit.

Measuring the quality of infection control in Dutch nursing homes using a standardized method; the Infection prevention RIsk Scan (IRIS)

PubMed Central

2014-01-01

Background We developed a standardised method to assess the quality of infection control in Dutch Nursing Home (NH), based on a cross-sectional survey that visualises the results. The method was called the Infection control RIsk Infection Scan (IRIS). We tested the applicability of this new tool in a multicentre surveillance executed June and July 2012. Methods The IRIS includes two patient outcome-variables, i.e. the prevalence of healthcare associated infections (HAI) and rectal carriage of Extended-Spectrum Beta-Lactamase (ESBL) producing Enterobacteriaceae (ESBL-E); two patient-related risk factors, i.e. use of medical devices, and antimicrobial therapy; and three ward-related risk factors, i.e. environmental contamination, availability of local guidelines, and shortcomings in infection prevention preconditions. Results were categorised as low-, intermediate- and high risk, presented in an easy-to-read graphic risk spider-plot. This plot was given as feedback to management and healthcare workers of the NH. Results Large differences were found among most the variables in the different NH. Common shortcomings were the availability of infection control guidelines and the level of environmental cleaning. Most striking differences were observed in the prevalence of ESBL carriage, ranged from zero to 20.6% (p < 0.001). Conclusions The IRIS provided a rapid and easy to understand assessment of the infection control situation of the participating NH. The results can be used to improve the quality of infection control based on the specific needs of a NH but needs further validation in future studies. Repeated measurement can determine the effectiveness of the interventions. This makes the IRIS a useful tool for quality systems. PMID:25243067

Control by quality: proposition of a typology.

PubMed

Pujo, P; Pillet, M

The application of Quality tools and methods in industrial management has always had a fundamental impact on the control of production. It influences the behavior of the actors concerned, while introducing the necessary notions and formalizations, especially for production systems with little or no automation, which constitute a large part of the industrial activity. Several quality approaches are applied in the workshop and are implemented at the level of the control. In this paper, the authors present a typology of the various approaches that have successively influenced control, such as statistical process control, quality assurance, and continuous improvement. First the authors present a parallel between production control and quality organizational structure. They note the duality between control, which is aimed at increasing productivity, and quality, which aims to satisfy the needs of the customer. They also note the hierarchical organizational structure of these two systems of management with, at each level, the notion of a feedback loop. This notion is fundamental to any kind of decision making. The paper is organized around the operational, tactical, and strategic levels, by describing for each level the main methods and tools for control by quality. The overview of these tools and methods starts at the operational level, with the Statistical Process Control, the Taguchi technique, and the "six sigma" approach. On the tactical level, we find a quality system approach, with a documented description of the procedures introduced in the firm. The management system can refer here to Quality Assurance, Total Productive Maintenance, or Management by Total Quality. The formalization through procedures of the rules of decision governing the process control enhances the validity of these rules. This leads to the enhancement of their reliability and to their consolidation. All this counterbalances the human, intrinsically fluctuating, behavior of the control

Measurement system with high accuracy for laser beam quality.

PubMed

Ke, Yi; Zeng, Ciling; Xie, Peiyuan; Jiang, Qingshan; Liang, Ke; Yang, Zhenyu; Zhao, Ming

2015-05-20

Presently, most of the laser beam quality measurement system collimates the optical path manually with low efficiency and low repeatability. To solve these problems, this paper proposed a new collimated method to improve the reliability and accuracy of the measurement results. The system accuracy controlled the position of the mirror to change laser beam propagation direction, which can realize the beam perpendicularly incident to the photosurface of camera. The experiment results show that the proposed system has good repeatability and the measuring deviation of M² factor is less than 0.6%.

[A strategy of constructing the technological system for quality control of Chinese medicine based on process control and management].

PubMed

Cheng, Yi-Yu; Qian, Zhong-Zhi; Zhang, Bo-Li

2017-01-01

The current situation, bottleneck problems and severe challenges in quality control technology of Chinese Medicine (CM) are briefly described. It is presented to change the phenomenon related to the post-test as the main means and contempt for process control in drug regulation, reverse the situation of neglecting the development of process control and management technology for pharmaceutical manufacture and reconstruct the technological system for quality control of CM products. The regulation and technology system based on process control and management for controlling CM quality should be established to solve weighty realistic problems of CM industry from the root causes, including backwardness of quality control technology, weakness of quality risk control measures, poor reputation of product quality and so on. By this way, the obstacles from poor controllability of CM product quality could be broken. Concentrating on those difficult problems and weak links in the technical field of CM quality control, it is proposed to build CMC (Chemistry, Manufacturing and Controls) regulation for CM products with Chinese characteristics and promote the regulation international recognition as soon as possible. The CMC technical framework, which is clinical efficacy-oriented, manufacturing manner-centered and process control-focused, was designed. To address the clinical characteristics of traditional Chinese medicine (TCM) and the production feature of CM manufacture, it is suggested to establish quality control engineering for CM manufacturing by integrating pharmaceutical analysis, TCM chemistry, TCM pharmacology, pharmaceutical engineering, control engineering, management engineering and other disciplines. Further, a theoretical model of quality control engineering for CM manufacturing and the methodology of digital pharmaceutical engineering are proposed. A technology pathway for promoting CM standard and realizing the strategic goal of CM internationalization is

Measurement Matters: Assessing Personal Qualities Other than Cognitive Ability for Educational Purposes

ERIC Educational Resources Information Center

Duckworth, Angela L.; Yeager, David Scott

2015-01-01

There has been perennial interest in personal qualities other than cognitive ability that determine success, including self-control, grit, growth mind-set, and many others. Attempts to measure such qualities for the purposes of educational policy and practice, however, are more recent. In this article, we identify serious challenges to doing so.…

EPA Summaries and Reports on Several State and Local PM Control Measures

EPA Pesticide Factsheets

A sample of existing control measures and their effectiveness, along with recommendations for improvement, can help states develop better control measures for reducing PM2.5 in order to attain 2012 PM2.5 National Ambient Air Quality Standards (NAAQS).

Interferometric measurement of displacements and displacement velocities for nondestructive quality control

NASA Astrophysics Data System (ADS)

Shpeĭzman, V. V.; Peschanskaya, N. N.

2007-07-01

It is shown that the interferometric measurement of small displacements and small-displacement velocities can be used to determine internal stresses or the stresses induced by an applied load in solids and to control structural changes in them. The interferometric method based on the measurement of the reaction of a solid to a small perturbation in its state of stress is applied to determine stresses from the deviation of the reaction to perturbations from that in the standard stress-free case. For structural control, this method is employed to study the specific features of the characteristics of microplastic deformation that appear after material treatment or operation and manifest themselves in the temperature and force dependences of the rate of a small inelastic strain.

Quality measurement and improvement in liver transplantation.

PubMed

Mathur, Amit K; Talwalkar, Jayant

2018-06-01

There is growing interest in the quality of health care delivery in liver transplantation. Multiple stakeholders, including patients, transplant providers and their hospitals, payers, and regulatory bodies have an interest in measuring and monitoring quality in the liver transplant process, and understanding differences in quality across centres. This article aims to provide an overview of quality measurement and regulatory issues in liver transplantation performed within the United States. We review how broader definitions of health care quality should be applied to liver transplant care models. We outline the status quo including the current regulatory agencies, public reporting mechanisms, and requirements around quality assurance and performance improvement (QAPI) activities. Additionally, we further discuss unintended consequences and opportunities for growth in quality measurement. Quality measurement and the integration of quality improvement strategies into liver transplant programmes hold significant promise, but multiple challenges to successful implementation must be addressed to optimise value. Copyright © 2018 European Association for the Study of the Liver. Published by Elsevier B.V. All rights reserved.

Development and implementation of an automated quantitative film digitizer quality control program

NASA Astrophysics Data System (ADS)

Fetterly, Kenneth A.; Avula, Ramesh T. V.; Hangiandreou, Nicholas J.

1999-05-01

A semi-automated, quantitative film digitizer quality control program that is based on the computer analysis of the image data from a single digitized test film was developed. This program includes measurements of the geometric accuracy, optical density performance, signal to noise ratio, and presampled modulation transfer function. The variability of the measurements was less than plus or minus 5%. Measurements were made on a group of two clinical and two laboratory laser film digitizers during a trial period of approximately four months. Quality control limits were established based on clinical necessity, vendor specifications and digitizer performance. During the trial period, one of the digitizers failed the performance requirements and was corrected by calibration.

Quality Measures in Orthopaedic Sports Medicine: A Systematic Review.

PubMed

Abrams, Geoffrey D; Greenberg, Daniel R; Dragoo, Jason L; Safran, Marc R; Kamal, Robin N

2017-10-01

To report the current quality measures that are applicable to orthopaedic sports medicine physicians. Six databases were searched with a customized search term to identify quality measures relevant to orthopaedic sports medicine surgeons: MEDLINE/PubMed, EMBASE, the National Quality Forum (NQF) Quality Positioning System (QPS), the Agency for Healthcare Research and Quality (AHRQ) National Quality Measures Clearinghouse (NQMC), the Physician Quality Reporting System (PQRS) database, and the American Academy of Orthopaedic Surgeons (AAOS) website. Results were screened by 2 Board-certified orthopaedic surgeons with fellowship training in sports medicine and dichotomized based on sports medicine-specific or general orthopaedic (nonarthroplasty) categories. Hip and knee arthroplasty measures were excluded. Included quality measures were further categorized based on Donabedian's domains and the Center for Medicare and Medicaid (CMS) National Quality Strategy priorities. A total of 1,292 quality measures were screened and 66 unique quality measures were included. A total of 47 were sports medicine-specific and 19 related to the general practice of orthopaedics for a fellowship-trained sports medicine specialist. Nineteen (29%) quality measures were collected within PQRS, with 5 of them relating to sports medicine and 14 relating to general orthopaedics. AAOS Clinical Practice Guidelines (CPGs) comprised 40 (60%) of the included measures and were all within sports medicine. Five (8%) additional measures were collected within AHRQ and 2 (3%) within NQF. Most quality measures consist of process rather than outcome or structural measures. No measures addressing concussions were identified. There are many existing quality measures relating to the practice of orthopaedic sports medicine. Most quality measures are process measures described within PQRS or AAOS CPGs. Knowledge of quality measures are important as they may be used to improve care, are increasingly being used to

Chronic Low Quality Sleep Impairs Postural Control in Healthy Adults.

PubMed

Furtado, Fabianne; Gonçalves, Bruno da Silva B; Abranches, Isabela Lopes Laguardia; Abrantes, Ana Flávia; Forner-Cordero, Arturo

2016-01-01

The lack of sleep, both in quality and quantity, is an increasing problem in modern society, often related to workload and stress. A number of studies have addressed the effects of acute (total) sleep deprivation on postural control. However, up to date, the effects of chronic sleep deficits, either in quantity or quality, have not been analyzed. Thirty healthy adults participated in the study that consisted of registering activity with a wrist actigraph for more than a week before performing a series of postural control tests. Sleep and circadian rhythm variables were correlated and the sum of activity of the least active 5-h period, L5, a rhythm variable, obtained the greater coefficient value with sleep quality variables (wake after sleep onset WASO and efficiency sleep). Cluster analysis was performed to classify subjects into two groups based on L5 (low and high). The balance tests scores used to asses postural control were measured using Biodex Balance System and were compared between the two groups with different sleep quality. The postural tests were divided into dynamic (platform tilt with eyes open, closed and cursor) and static (clinical test of sensory integration). The results showed that during the tests with eyes closed, the group with worse sleep quality had also worse postural control performance. Lack of vision impairs postural balance more deeply in subjects with chronic sleep inefficiency. Chronic poor sleep quality impairs postural control similarly to total sleep deprivation.

Chronic Low Quality Sleep Impairs Postural Control in Healthy Adults

PubMed Central

Gonçalves, Bruno da Silva B.; Abranches, Isabela Lopes Laguardia; Abrantes, Ana Flávia

2016-01-01

The lack of sleep, both in quality and quantity, is an increasing problem in modern society, often related to workload and stress. A number of studies have addressed the effects of acute (total) sleep deprivation on postural control. However, up to date, the effects of chronic sleep deficits, either in quantity or quality, have not been analyzed. Thirty healthy adults participated in the study that consisted of registering activity with a wrist actigraph for more than a week before performing a series of postural control tests. Sleep and circadian rhythm variables were correlated and the sum of activity of the least active 5-h period, L5, a rhythm variable, obtained the greater coefficient value with sleep quality variables (wake after sleep onset WASO and efficiency sleep). Cluster analysis was performed to classify subjects into two groups based on L5 (low and high). The balance tests scores used to asses postural control were measured using Biodex Balance System and were compared between the two groups with different sleep quality. The postural tests were divided into dynamic (platform tilt with eyes open, closed and cursor) and static (clinical test of sensory integration). The results showed that during the tests with eyes closed, the group with worse sleep quality had also worse postural control performance. Lack of vision impairs postural balance more deeply in subjects with chronic sleep inefficiency. Chronic poor sleep quality impairs postural control similarly to total sleep deprivation. PMID:27732604

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality control. 74.6 Section 74.6 Mineral... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and... DUST SAMPLING DEVICES Approval Requirements for Coal Mine Dust Personal Sampler Unit § 74.6 Quality...

Gratitude mediates quality of life differences between fibromyalgia patients and healthy controls.

PubMed

Toussaint, Loren; Sirois, Fuschia; Hirsch, Jameson; Weber, Annemarie; Vajda, Christian; Schelling, Jorg; Kohls, Niko; Offenbacher, Martin

2017-09-01

Despite a growing literature on the benefits of gratitude for adjustment to chronic illness, little is known about gratitude in medical populations compared to healthy populations, or the degree to which potential deficits in gratitude might impact quality of life. The purpose of the present study was to (1) examine levels of gratitude and quality of life in fibromyalgia patients and healthy controls and (2) consider the role of gratitude in explaining quality of life differences between fibromyalgia patients and healthy controls. Participants were 173 fibromyalgia patients and 81 healthy controls. All participants completed measures of gratitude, quality of life, and socio-demographics. Although gratitude was positively associated with quality of life, levels of gratitude and quality of life were lower in the fibromyalgia sample relative to the healthy controls. This difference in gratitude partially mediated differences in quality of life between the two groups after controlling for socio-demographic variables. Our findings suggest that gratitude is a valuable positive psychological trait for quality of life in people with fibromyalgia. Interventions to improve gratitude in this patient population may also bring enhancement in quality of life.

[Quality control in herbal supplements].

PubMed

Oelker, Luisa

2005-01-01

Quality and safety of food and herbal supplements are the result of a whole of different elements as good manufacturing practice and process control. The process control must be active and able to individuate and correct all possible hazards. The main and most utilized instrument is the hazard analysis critical control point (HACCP) system the correct application of which can guarantee the safety of the product. Herbal supplements need, in addition to standard quality control, a set of checks to assure the harmlessness and safety of the plants used.

Quality control education in the community college

NASA Technical Reports Server (NTRS)

Greene, J. Griffen; Wilson, Steve

1966-01-01

This paper describes the Quality Control Program at Daytona Beach Junior College, including course descriptions. The program in quality control required communication between the college and the American Society for Quality Control (ASQC). The college has machinery established for certification of the learning process, and the society has the source of teachers who are competent in the technical field and who are the employers of the educational products. The associate degree for quality control does not have a fixed program, which can serve all needs, any more than all engineering degrees have identical programs. The main ideas which would be common to all quality control programs are the concept of economic control of a repetitive process and the concept of developing individual potentialities into individuals who are needed and productive.

Information quality-control model

NASA Technical Reports Server (NTRS)

Vincent, D. A.

1971-01-01

Model serves as graphic tool for estimating complete product objectives from limited input information, and is applied to cost estimations, product-quality evaluations, and effectiveness measurements for manpower resources allocation. Six product quality levels are defined.

23 CFR 1340.8 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-04-01

... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data collection...) Statistical review. Survey results shall be reviewed and approved by a survey statistician, i.e., a person...

23 CFR 1340.8 - Quality control.

Code of Federal Regulations, 2014 CFR

2014-04-01

... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data collection...) Statistical review. Survey results shall be reviewed and approved by a survey statistician, i.e., a person...

23 CFR 1340.8 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-04-01

... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data collection...) Statistical review. Survey results shall be reviewed and approved by a survey statistician, i.e., a person...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

42 CFR 84.41 - Quality control plans; contents.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality Control § 84.41 Quality control plans; contents. (a) Each quality control plan shall contain provisions for the...

Instrument Quality Control.

PubMed

Jayakody, Chatura; Hull-Ryde, Emily A

2016-01-01

Well-defined quality control (QC) processes are used to determine whether a certain procedure or action conforms to a widely accepted standard and/or set of guidelines, and are important components of any laboratory quality assurance program (Popa-Burke et al., J Biomol Screen 14: 1017-1030, 2009). In this chapter, we describe QC procedures useful for monitoring the accuracy and precision of laboratory instrumentation, most notably automated liquid dispensers. Two techniques, gravimetric QC and photometric QC, are highlighted in this chapter. When used together, these simple techniques provide a robust process for evaluating liquid handler accuracy and precision, and critically underpin high-quality research programs.

14 CFR 145.211 - Quality control system.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Quality control system. 145.211 Section 145...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable to...

18 CFR 12.40 - Quality control programs.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Quality control... PROJECT WORKS Other Responsibilities of Applicant or Licensee § 12.40 Quality control programs. (a... meeting any requirements or standards set by the Regional Engineer. If a quality control program is...

18 CFR 12.40 - Quality control programs.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Quality control... PROJECT WORKS Other Responsibilities of Applicant or Licensee § 12.40 Quality control programs. (a... meeting any requirements or standards set by the Regional Engineer. If a quality control program is...

14 CFR 145.211 - Quality control system.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Quality control system. 145.211 Section 145...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable to...

[Development of whole process quality control and management system of traditional Chinese medicine decoction pieces based on traditional Chinese medicine quality tree].

PubMed

Yu, Wen-Kang; Dong, Ling; Pei, Wen-Xuan; Sun, Zhi-Rong; Dai, Jun-Dong; Wang, Yun

2017-12-01

The whole process quality control and management of traditional Chinese medicine (TCM) decoction pieces is a system engineering, involving the base environment, seeds and seedlings, harvesting, processing and other multiple steps, so the accurate identification of factors in TCM production process that may induce the quality risk, as well as reasonable quality control measures are very important. At present, the concept of quality risk is mainly concentrated in the aspects of management and regulations, etc. There is no comprehensive analysis on possible risks in the quality control process of TCM decoction pieces, or analysis summary of effective quality control schemes. A whole process quality control and management system for TCM decoction pieces based on TCM quality tree was proposed in this study. This system effectively combined the process analysis method of TCM quality tree with the quality risk management, and can help managers to make real-time decisions while realizing the whole process quality control of TCM. By providing personalized web interface, this system can realize user-oriented information feedback, and was convenient for users to predict, evaluate and control the quality of TCM. In the application process, the whole process quality control and management system of the TCM decoction pieces can identify the related quality factors such as base environment, cultivation and pieces processing, extend and modify the existing scientific workflow according to their own production conditions, and provide different enterprises with their own quality systems, to achieve the personalized service. As a new quality management model, this paper can provide reference for improving the quality of Chinese medicine production and quality standardization. Copyright© by the Chinese Pharmaceutical Association.

A quality improvement plan for hypertension control: the INCOTECA Project (INterventions for COntrol of hyperTEnsion in CAtalonia)

PubMed Central

Vallès-Fernandez, Roser; Rosell-Murphy, Magdalena; Correcher-Aventin, Olga; Mengual-Martínez, Lucas; Aznar-Martínez, Núria; Prieto-De Lamo, Gemma; Franzi-Sisó, Alícia; Puig-Manresa, Jordi; Ma Bonet-Simó, Josep

2009-01-01

Background Different studies have shown insufficient blood pressure (BP) control in hypertensive patients. Multiple factors influence hypertension management, and the quality of primary care is one of them. We decided therefore to evaluate the effectiveness of a quality improvement plan directed at professionals of Primary Health Care Teams (PHCT) with the aim to achieve a better control of hypertension. The hypothesis of the study is that the implementation of a quality improvement plan will improve the control of hypertension. The primary aim of this study will be to evaluate the effectiveness of this plan. Methods and design Design: multicentric study quasi-experimental before – after with control group. The non-randomised allocation of the intervention will be done at PHCT level. Setting: 18 PHCT in the Barcelona province (Spain). Sample: all patients with a diagnosis of hypertension (population based study). Exclusion criteria: patients with a diagnosis of hypertension made later than 01/01/2006 and patients younger than 18 years. Intervention: a quality improvement plan, which targets primary health care professionals and includes educational sessions, feedback to health professionals, audit and implementation of recommended clinical practice guidelines for the management of hypertensive patients. Measurements: age, sex, associated co-morbidity (diabetes mellitus type I and II, heart failure and renal failure). The following variables will be recorded: BP measurement, cardiovascular risk and antihypertensive drugs used. Results will be measured before the start of the intervention and twelve months after the start of the study. Dependent variable: prevalence of hypertensive patients with poor BP control. Analysis: Chi-square test and Student's t-test will be used to measure the association between independent qualitative and quantitative variables, respectively. Non-parametric tests will be used for the analysis of non-normally distributed variables

Quality Control in construction.

DTIC Science & Technology

1984-01-01

behavioral scientists. In 1962, Dr. Kaoru Ishikawa gave shape to the form of training which featured intradepartmental groups of ten or so workers seated...and Japanese circles bears closer scrutiny. 4.3.1 Japanese Ingredients of Quality The founder of quality circles, Dr. Kaoru Ishikawa , gives six...around 51 a table; hence the name Quality Control Circle. 4 Dr. 0 Ishikawa was an engineering professor at Tokyo University, and the circles were

Bioassay selection, experimental design and quality control/assurance for use in effluent assessment and control.

PubMed

Johnson, Ian; Hutchings, Matt; Benstead, Rachel; Thain, John; Whitehouse, Paul

2004-07-01

In the UK Direct Toxicity Assessment Programme, carried out in 1998-2000, a series of internationally recognised short-term toxicity test methods for algae, invertebrates and fishes, and rapid methods (ECLOX and Microtox) were used extensively. Abbreviated versions of conventional tests (algal growth inhibition tests, Daphnia magna immobilisation test and the oyster embryo-larval development test) were valuable for toxicity screening of effluent discharges and the identification of causes and sources of toxicity. Rapid methods based on chemiluminescence and bioluminescence were not generally useful in this programme, but may have a role where the rapid test has been shown to be an acceptable surrogate for a standardised test method. A range of quality assurance and control measures were identified. Requirements for quality control/assurance are most stringent when deriving data for characterising the toxic hazards of effluents and monitoring compliance against a toxicity reduction target. Lower quality control/assurance requirements can be applied to discharge screening and the identification of causes and sources of toxicity.

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quality control. 74.6 Section 74.6 Mineral... control. The applicant shall describe the way in which each lot of components will be sampled and tested... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and...

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality control. 74.6 Section 74.6 Mineral... control. The applicant shall describe the way in which each lot of components will be sampled and tested... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and...

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quality control. 74.6 Section 74.6 Mineral... control. The applicant shall describe the way in which each lot of components will be sampled and tested... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and...

Health Care Quality: Measuring Obesity in Performance Frameworks.

PubMed

Zvenyach, Tracy; Pickering, Matthew K

2017-08-01

Obesity affects over one-third of Americans and leads to several chronic and costly comorbid conditions. The national movement toward value-based care calls for a refocusing of efforts to address the US obesity epidemic. To help set the stage, the current landscape of obesity-specific quality measures was evaluated. Seven quality measure databases and nine professional societies were searched. Inclusion and exclusion criteria were applied. Measures were then classified by domain and by implementation in national public programs. Eleven obesity-specific quality measures in adults were identified (nine process and two outcome). Three measures received National Quality Forum (NQF) endorsement. Two measures were actively used within Centers for Medicare and Medicaid Services (CMS) programs. Only one measure was both NQF-endorsed and used by CMS. Limitations exist with respect to obesity-specific quality metrics. Such gaps provide opportunities for obesity care specialists to engage and offer valuable insights and pragmatic approaches toward quality measurement. © 2017 The Obesity Society.

Quality Assurance and Quality Control, Part 2.

PubMed

Akers, Michael J

2015-01-01

The tragedy surrounding the New England Compounding Center and contaminated steroid syringe preparations clearly points out what can happen if quality-assurance and quality-control procedures are not strictly practiced in the compounding of sterile preparations. This article is part 2 of a two-part article on requirements to comply with United States Pharmacopeia general chapters <797> and <1163> with respect to quality assurance of compounded sterile preparations. Part 1 covered documentation requirements, inspection procedures, compounding accuracy checks, and part of a discussion on bacterial endotoxin testing. Part 2 covers sterility testing, the completion from part 1 on bacterial endotoxin testing, a brief dicussion of United States Pharmacopeia <1163>, and advances in pharmaceutical quality systems.

Guidance for Efficient Small Animal Imaging Quality Control.

PubMed

Osborne, Dustin R; Kuntner, Claudia; Berr, Stuart; Stout, David

2017-08-01

Routine quality control is a critical aspect of properly maintaining high-performance small animal imaging instrumentation. A robust quality control program helps produce more reliable data both for academic purposes and as proof of system performance for contract imaging work. For preclinical imaging laboratories, the combination of costs and available resources often limits their ability to produce efficient and effective quality control programs. This work presents a series of simplified quality control procedures that are accessible to a wide range of preclinical imaging laboratories. Our intent is to provide minimum guidelines for routine quality control that can assist preclinical imaging specialists in setting up an appropriate quality control program for their facility.

History and background of quality measurement.

PubMed

Chun, Jonathan; Bafford, Andrea Chao

2014-03-01

Health care quality measurement has become increasingly emphasized, as providers and administrators respond to public and government demands for improved patient care. This article will review the evolution of surgical quality measurement and improvement from its infancy in the 1850s to the vast efforts being undertaken today.

42 CFR 84.256 - Quality control requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Quality control requirements. 84.256 Section 84.256... § 84.256 Quality control requirements. (a) In addition to the construction and performance requirements specified in §§ 84.251, 84.252, 84.253, 84.254, and 84.255, the quality control requirements in paragraphs...

42 CFR 84.256 - Quality control requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Quality control requirements. 84.256 Section 84.256... § 84.256 Quality control requirements. (a) In addition to the construction and performance requirements specified in §§ 84.251, 84.252, 84.253, 84.254, and 84.255, the quality control requirements in paragraphs...

42 CFR 84.256 - Quality control requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Quality control requirements. 84.256 Section 84.256... § 84.256 Quality control requirements. (a) In addition to the construction and performance requirements specified in §§ 84.251, 84.252, 84.253, 84.254, and 84.255, the quality control requirements in paragraphs...

42 CFR 84.256 - Quality control requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Quality control requirements. 84.256 Section 84.256... § 84.256 Quality control requirements. (a) In addition to the construction and performance requirements specified in §§ 84.251, 84.252, 84.253, 84.254, and 84.255, the quality control requirements in paragraphs...

42 CFR 84.256 - Quality control requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Quality control requirements. 84.256 Section 84.256... § 84.256 Quality control requirements. (a) In addition to the construction and performance requirements specified in §§ 84.251, 84.252, 84.253, 84.254, and 84.255, the quality control requirements in paragraphs...

Enhancement of the Automated Quality Control Procedures for the International Soil Moisture Network

NASA Astrophysics Data System (ADS)

Heer, Elsa; Xaver, Angelika; Dorigo, Wouter; Messner, Romina

2017-04-01

In-situ soil moisture observations are still trusted to be the most reliable data to validate remotely sensed soil moisture products. Thus, the quality of in-situ soil moisture observations is of high importance. The International Soil Moisture Network (ISMN; http://ismn.geo.tuwien.ac.at/) provides in-situ soil moisture data from all around the world. The data is collected from individual networks and data providers, measured by different sensors in various depths. The data sets which are delivered in different units, time zones and data formats are then transformed into homogeneous data sets. An erroneous behavior of soil moisture data is very difficult to detect, due to annual and daily changes and most significantly the high influence of precipitation and snow melting processes. Only few of the network providers have a quality assessment for their data sets. Therefore, advanced quality control procedures have been developed for the ISMN (Dorigo et al. 2013). Three categories of quality checks were introduced: exceeding boundary values, geophysical consistency checks and a spectrum based approach. The spectrum based quality control algorithms aim to detect erroneous measurements which occur within plausible geophysical ranges, e.g. a sudden drop in soil moisture caused by a sensor malfunction. By defining several conditions which have to be met by the original soil moisture time series and their first and second derivative, such error types can be detected. Since the development of these sophisticated methods many more data providers shared their data with the ISMN and new types of erroneous measurements were identified. Thus, an enhancement of the automated quality control procedures became necessary. In the present work, we introduce enhancements of the existing quality control algorithms. Additionally, six completely new quality checks have been developed, e.g. detection of suspicious values before or after NAN-values, constant values and values that lie in a

The World Optical Depth Research and Calibration Center (WORCC) quality assurance and quality control of GAW-PFR AOD measurements

NASA Astrophysics Data System (ADS)

Kazadzis, Stelios; Kouremeti, Natalia; Nyeki, Stephan; Gröbner, Julian; Wehrli, Christoph

2018-02-01

The World Optical Depth Research Calibration Center (WORCC) is a section within the World Radiation Center at Physikalisches-Meteorologisches Observatorium (PMOD/WRC), Davos, Switzerland, established after the recommendations of the World Meteorological Organization for calibration of aerosol optical depth (AOD)-related Sun photometers. WORCC is mandated to develop new methods for instrument calibration, to initiate homogenization activities among different AOD networks and to run a network (GAW-PFR) of Sun photometers. In this work we describe the calibration hierarchy and methods used under WORCC and the basic procedures, tests and processing techniques in order to ensure the quality assurance and quality control of the AOD-retrieved data.

More quality measures versus measuring what matters: a call for balance and parsimony

PubMed Central

Nelson, Eugene C; Pryor, David B; James, Brent; Swensen, Stephen J; Kaplan, Gary S; Weissberg, Jed I; Bisognano, Maureen; Yates, Gary R; Hunt, Gordon C

2012-01-01

External groups requiring measures now include public and private payers, regulators, accreditors and others that certify performance levels for consumers, patients and payers. Although benefits have accrued from the growth in quality measurement, the recent explosion in the number of measures threatens to shift resources from improving quality to cover a plethora of quality-performance metrics that may have a limited impact on the things that patients and payers want and need (ie, better outcomes, better care, and lower per capita costs). Here we propose a policy that quality measurement should be: balanced to meet the need of end users to judge quality and cost performance and the need of providers to continuously improve the quality, outcomes and costs of their services; and parsimonious to measure quality, outcomes and costs with appropriate metrics that are selected based on end-user needs. PMID:22893696

More quality measures versus measuring what matters: a call for balance and parsimony.

PubMed

Meyer, Gregg S; Nelson, Eugene C; Pryor, David B; James, Brent; Swensen, Stephen J; Kaplan, Gary S; Weissberg, Jed I; Bisognano, Maureen; Yates, Gary R; Hunt, Gordon C

2012-11-01

External groups requiring measures now include public and private payers, regulators, accreditors and others that certify performance levels for consumers, patients and payers. Although benefits have accrued from the growth in quality measurement, the recent explosion in the number of measures threatens to shift resources from improving quality to cover a plethora of quality-performance metrics that may have a limited impact on the things that patients and payers want and need (ie, better outcomes, better care, and lower per capita costs). Here we propose a policy that quality measurement should be: balanced to meet the need of end users to judge quality and cost performance and the need of providers to continuously improve the quality, outcomes and costs of their services; and parsimonious to measure quality, outcomes and costs with appropriate metrics that are selected based on end-user needs.

Automated quality control for stitching of textile articles

NASA Technical Reports Server (NTRS)

Miller, Jeffrey L. (Inventor); Markus, Alan (Inventor)

1999-01-01

Quality control for stitching of a textile article is performed by measuring thread tension in the stitches as the stitches are being made, determining locations of the stitches, and generating a map including the locations and stitching data derived from the measured thread tensions. The stitching data can be analyzed, off-line or in real time, to identify defective stitches. Defective stitches can then be repaired. Real time analysis of the thread tensions allows problems such as broken needle threads to be corrected immediately.

Advanced Quality Control Theory for Training and Education: A Guide to Optimizing Training and Education Efforts

ERIC Educational Resources Information Center

Heppler, Brad

2008-01-01

This is a book about quality and how to control quality through deliberate actions on the part of the professionals developing and implementing the instances of instruction available at an organization. Quality control theory favors no particular learning philosophy and is only directed towards aspects of how, what, where and when measurements are…

[Strategies and development of quality assurance and control in the ELSA-Brasil].

PubMed

Schmidt, Maria Inês; Griep, Rosane Härter; Passos, Valéria Maria; Luft, Vivian Cristine; Goulart, Alessandra Carvalho; Menezes, Greice Maria de Souza; Molina, Maria del Carmen Bisi; Vigo, Alvaro; Nunes, Maria Angélica

2013-06-01

The ELSA-Brasil (Estudo Longitudinal de Saúde do Adulto - Brazilian Longitudinal Study for Adult Health) is a cohort study composed of 15,105 adults followed up in order to assess the development of chronic diseases, especially diabetes and cardiovascular disease. Its size, multicenter nature and the diversity of measurements required effective and efficient mechanisms of quality assurance and control. The main quality assurance activities (those developed before data collection) were: careful selection of research instruments, centralized training and certification, pretesting and pilot studies, and preparation of operation manuals for the procedures. Quality control activities (developed during data collection and processing) were performed more intensively at the beginning, when routines had not been established yet. The main quality control activities were: periodic observation of technicians, test-retest studies, data monitoring, network of supervisors, and cross visits. Data that estimate the reliability of the obtained information attest that the quality goals have been achieved.

Incorporating Quality Control Information in the Sensor Web

NASA Astrophysics Data System (ADS)

Devaraju, Anusuriya; Kunkel, Ralf; Bogena, Heye

2013-04-01

The rapid development of sensing technologies had led to the creation of large amounts of heterogeneous environmental observations. The Sensor Web provides a wider access to sensors and observations via common protocols and specifications. Observations typically go through several levels of quality control, and aggregation before they are made available to end-users. Raw data are usually inspected, and related quality flags are assigned. Data are gap-filled, and errors are removed. New data series may also be derived from one or more corrected data sets. Until now, it is unclear how these kinds of information can be captured in the Sensor Web Enablement (SWE) framework. Apart from the quality measures (e.g., accuracy, precision, tolerance, or confidence), the levels of observational series, the changes applied, and the methods involved must be specified. It is important that this kind of quality control information is well described and communicated to end-users to allow for a better usage and interpretation of data products. In this paper, we describe how quality control information can be incorporated into the SWE framework. Concerning this, first, we introduce the TERENO (TERrestrial ENvironmental Observatories), an initiative funded by the large research infrastructure program of the Helmholtz Association in Germany. The main goal of the initiative is to facilitate the study of long-term effects of climate and land use changes. The TERENO Online Data RepOsitORry (TEODOOR) is a software infrastructure that supports acquisition, provision, and management of observations within TERENO via SWE specifications and several other OGC web services. Next, we specify changes made to the existing observational data model to incorporate quality control information. Here, we describe the underlying TERENO data policy in terms of provision and maintenance issues. We present data levels, and their implementation within TEODOOR. The data levels are adapted from those used by

Measuring Up: Implementing a Dental Quality Measure in the Electronic Health Record Context

PubMed Central

Bhardwaj, Aarti; Ramoni, Rachel; Kalenderian, Elsbeth; Neumann, Ana; Hebballi, Nutan B; White, Joel M; McClellan, Lyle; Walji, Muhammad F

2015-01-01

Background Quality improvement requires quality measures that are validly implementable. In this work, we assessed the feasibility and performance of an automated electronic Meaningful Use dental clinical quality measure (percentage of children who received fluoride varnish). Methods We defined how to implement the automated measure queries in a dental electronic health record (EHR). Within records identified through automated query, we manually reviewed a subsample to assess the performance of the query. Results The automated query found 71.0% of patients to have had fluoride varnish compared to 77.6% found using the manual chart review. The automated quality measure performance was 90.5% sensitivity, 90.8% specificity, 96.9% positive predictive value, and 75.2% negative predictive value. Conclusions Our findings support the feasibility of automated dental quality measure queries in the context of sufficient structured data. Information noted only in the free text rather than in structured data would require natural language processing approaches to effectively query. Practical Implications To participate in self-directed quality improvement, dental clinicians must embrace the accountability era. Commitment to quality will require enhanced documentation in order to support near-term automated calculation of quality measures. PMID:26562736

The ASC/SIL ratio for cytopathologists as a quality control measure: a follow-up study.

PubMed

Nascimento, Alessandra F; Cibas, Edmund S

2007-10-01

Monitoring the relative frequency of the interpretations of atypical squamous cells (ASC) and squamous intraepithelial lesions (SIL) has been proposed as a quality control measure. To assess its value, an ASC/SIL ratio was calculated every 6 months for 3.5 years, and confidential feedback was provided to 10 cytopathologists (CPs). By using simple regression analysis, we analyzed the initial and final ASC/SIL ratios for individual CPs and for the entire group. The ratio was below the upper benchmark of 3:1 for all but 1 CP during every 6-month period. The ratio for all CPs combined showed a downward trend (from 2.05 to 1.73). The ratio for 6 CPs decreased, and for two of them the decrease was statistically significant. One CP showed a statistically significant increase in the ASC/SIL ratio. The decrease for some CPs likely reflects the salutary effect of confidential feedback and counseling.

Quality control concept and recent developments of the light climatic observatory at Arosa: Ozone measuring station of the Swiss Meteorological Institute (LKO)

NASA Technical Reports Server (NTRS)

Hoegger, Bruno; Viatte, Pierre; Levrat, Gilbert; Bader, Juerg; Ribordy, Pascale; Schill, Herbert; Staehelin, Johannes

1994-01-01

Total ozone observations of two Dobson instruments (D15 and D101, C- and AD wavelength pair observations) and of two Brewer instruments (Br40 and Br72) are currently performed at the LKO at Arosa. A quality control concept is presented in order to make best use of the large number of quasi-simultaneous measurements. The longest ozone series of the world is mainly based on the measurements of the Dobson instrument D15 (wavelength pair C). Since the last years D15 has suffered from instrumental problems. The transformation of the longterm series to the measurements of D101(AD) is described.

A Data Quality Filter for PMU Measurements: Description, Experience, and Examples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Follum, James D.; Amidan, Brett G.

Networks of phasor measurement units (PMUs) continue to grow, and along with them, the amount of data available for analysis. With so much data, it is impractical to identify and remove poor quality data manually. The data quality filter described in this paper was developed for use with the Data Integrity and Situation Awareness Tool (DISAT), which analyzes PMU data to identify anomalous system behavior. The filter operates based only on the information included in the data files, without supervisory control and data acquisition (SCADA) data, state estimator values, or system topology information. Measurements are compared to preselected thresholds tomore » determine if they are reliable. Along with the filter's description, examples of data quality issues from application of the filter to nine months of archived PMU data are provided. The paper is intended to aid the reader in recognizing and properly addressing data quality issues in PMU data.« less

Conflict Inhibitory Control Facilitates Pretense Quality in Young Preschoolers

PubMed Central

Van Reet, Jennifer

2013-01-01

The present research explores the role of inhibitory control in young preschoolers’ pretense ability using an ego depletion paradigm. In Experiment 1 (N = 56), children’s pretense ability was assessed either before or after participating in conflict inhibitory control or control tasks, and in Experiment 2 (N = 36), pretense ability was measured after children engaged in either conflict or delay inhibitory control tasks. In both experiments, pretense scores were significantly higher only after engaging in conflict inhibitory control tasks. Further, pretense scores were positively correlated with inhibitory control scores when conflict inhibitory control was not experienced first. This pattern of results suggests that inhibitory control may underlie pretense, and conflict inhibitory control can boost the quality of children’s subsequent pretending. PMID:26074736

7 CFR 58.928 - Quality control tests.

Code of Federal Regulations, 2013 CFR

2013-01-01

... quality test shall be made to determine product stability. ... 7 Agriculture 3 2013-01-01 2013-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to...

7 CFR 58.928 - Quality control tests.

Code of Federal Regulations, 2012 CFR

2012-01-01

... quality test shall be made to determine product stability. ... 7 Agriculture 3 2012-01-01 2012-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to...

Effect of Sahaja yoga meditation on quality of life, anxiety, and blood pressure control.

PubMed

Chung, Sheng-Chia; Brooks, Maria M; Rai, Madhur; Balk, Judith L; Rai, Sandeep

2012-06-01

The present study investigates the effect of Sahaja yoga meditation on quality of life, anxiety, and blood pressure control. The prospective observational cohort study enrolled two study groups: those receiving treatment from the International Sahaja Yoga Research and Health Center (meditation group) and those receiving treatment from the Mahatma Gandhi Mission Hospital (control group). Researchers measured quality of life, anxiety, and blood pressure before and after treatment. Sixty-seven (67) participants in the meditation group and 62 participants in the control group completed the study. The two groups were comparable in demographic and clinical characteristics. At baseline, the meditation group had higher quality of life (p<0.001) than controls but similar anxiety level (p=0.74) to controls. Within-group pre- versus post-treatment comparisons showed significant improvement in quality of life, anxiety, and blood pressure in the meditation group (p<0.001), while in controls, quality of life deteriorated and there was no improvement in blood pressure. The improvement in quality of life, anxiety reduction, and blood pressure control was greater in the meditation group. The beneficial effect of meditation remained significant after adjusting for confounders. Meditation treatment was associated with significant improvements in quality of life, anxiety reduction, and blood pressure control.

Methodological and Reporting Quality of Comparative Studies Evaluating Health-Related Quality of Life of Colorectal Cancer Patients and Controls: A Systematic Review.

PubMed

Wong, Carlos K H; Guo, Vivian Y W; Chen, Jing; Lam, Cindy L K

2016-11-01

Health-related quality of life is an important outcome measure in patients with colorectal cancer. Comparison with normative data has been increasingly undertaken to assess the additional impact of colorectal cancer on health-related quality of life. This review aimed to critically appraise the methodological details and reporting characteristics of comparative studies evaluating differences in health-related quality of life between patients and controls. A systematic search of English-language literature published between January 1985 and May 2014 was conducted through a database search of PubMed, Web of Science, Embase, and Medline. Comparative studies reporting health-related quality-of-life outcomes among patients who have colorectal cancer and controls were selected. Methodological and reporting quality per comparison study was evaluated based on a 11-item methodological checklist proposed by Efficace in 2003 and a set of criteria predetermined by reviewers. Thirty-one comparative studies involving >10,000 patients and >10,000 controls were included. Twenty-three studies (74.2%) originated from European countries, with the largest number from the Netherlands (n = 6). Twenty-eight studies (90.3%) compared the health-related quality of life of patients with normative data published elsewhere, whereas the remaining studies recruited a group of patients who had colorectal cancer and a group of control patients within the same studies. The European Organisation for Research and Treatment of Cancer Quality-of-Life Questionnaire Core 30 was the most extensively used instrument (n = 16; 51.6%). Eight studies (25.8%) were classified as "probably robust" for clinical decision making according to the Efficace standard methodological checklist. Our further quality assessment revealed the lack of score differences reported (61.3%), contemporary comparisons (36.7%), statistical significance tested (38.7%), and matching of control group (58.1%), possibly leading to

Sunway Medical Laboratory Quality Control Plans Based on Six Sigma, Risk Management and Uncertainty.

PubMed

Jairaman, Jamuna; Sakiman, Zarinah; Li, Lee Suan

2017-03-01

Sunway Medical Centre (SunMed) implemented Six Sigma, measurement uncertainty, and risk management after the CLSI EP23 Individualized Quality Control Plan approach. Despite the differences in all three approaches, each implementation was beneficial to the laboratory, and none was in conflict with another approach. A synthesis of these approaches, built on a solid foundation of quality control planning, can help build a strong quality management system for the entire laboratory. Copyright © 2016 Elsevier Inc. All rights reserved.

Field methods and quality-assurance plan for water-quality activities and water-level measurements, U.S. Geological Survey, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Bartholomay, Roy C.; Maimer, Neil V.; Wehnke, Amy J.

2014-01-01

Water-quality activities and water-level measurements by the personnel of the U.S. Geological Survey (USGS) Idaho National Laboratory (INL) Project Office coincide with the USGS mission of appraising the quantity and quality of the Nation’s water resources. The activities are carried out in cooperation with the U.S. Department of Energy (DOE) Idaho Operations Office. Results of the water-quality and hydraulic head investigations are presented in various USGS publications or in refereed scientific journals and the data are stored in the National Water Information System (NWIS) database. The results of the studies are used by researchers, regulatory and managerial agencies, and interested civic groups. In the broadest sense, quality assurance refers to doing the job right the first time. It includes the functions of planning for products, review and acceptance of the products, and an audit designed to evaluate the system that produces the products. Quality control and quality assurance differ in that quality control ensures that things are done correctly given the “state-of-the-art” technology, and quality assurance ensures that quality control is maintained within specified limits.

Coping and social problem solving correlates of asthma control and quality of life.

PubMed

McCormick, Sean P; Nezu, Christine M; Nezu, Arthur M; Sherman, Michael; Davey, Adam; Collins, Bradley N

2014-02-01

In a sample of adults with asthma receiving care and medication in an outpatient pulmonary clinic, this study tested for statistical associations between social problem-solving styles, asthma control, and asthma-related quality of life. These variables were measured cross sectionally as a first step toward more systematic application of social problem-solving frameworks in asthma self-management training. Recruitment occurred during pulmonology clinic service hours. Forty-four adults with physician-confirmed diagnosis of asthma provided data including age, gender, height, weight, race, income, and comorbid conditions. The Asthma Control Questionnaire, the Mini Asthma Quality of Life Questionnaire (Short Form), and peak expiratory force measures offered multiple views of asthma health at the time of the study. Maladaptive coping (impulsive and careless problem-solving styles) based on transactional stress models of health were assessed with the Social Problem-Solving Inventory-Revised: Short Form. Controlling for variance associated with gender, age, and income, individuals reporting higher impulsive-careless scores exhibited significantly lower scores on asthma control (β = 0.70, p = 0.001, confidence interval (CI) [0.37-1.04]) and lower asthma-related quality of life (β = 0.79, p = 0.017, CI [0.15-1.42]). These findings suggest that specific maladaptive problem-solving styles may uniquely contribute to asthma health burdens. Because problem-solving coping strategies are both measureable and teachable, behavioral interventions aimed at facilitating adaptive coping and problem solving could positively affect patient's asthma management and quality of life.

7 CFR 981.442 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Quality control. 981.442 Section 981.442 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Administrative Rules and Regulations § 981.442 Quality control. (a) Incoming. Pursuant to § 981.42(a), the...

7 CFR 981.442 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Quality control. 981.442 Section 981.442 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Administrative Rules and Regulations § 981.442 Quality control. (a) Incoming. Pursuant to § 981.42(a), the...

7 CFR 981.442 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Quality control. 981.442 Section 981.442 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Administrative Rules and Regulations § 981.442 Quality control. (a) Incoming. Pursuant to § 981.42(a), the...

Development of the Quality Assurance/Quality Control Procedures for a Neutron Interrogation System

NASA Astrophysics Data System (ADS)

Obhođaš, Jasmina; Sudac, Davorin; Valković, Vladivoj

2016-06-01

In order to perform Quality Assurance/Quality Control (QA/QC) procedures for a system dedicated to the neutron interrogation of objects for the presence of threat materials one needs to perform measurements of reference materials (RM) i.e. simulants having the same (or similar) atomic ratios as real materials. It is well known that explosives, drugs, and various other benign materials, contain chemical elements such as hydrogen, oxygen, carbon and nitrogen in distinctly different quantities. For example, a high carbon-to-oxygen ratio (C/O) is characteristic of drugs. Explosives can be differentiated by measurement of both (C/O) and nitrogen-to-oxygen (N/O) ratios. The C/N ratio of the chemical warfare agents, coupled with the measurement of elements such as fluorine and phosphorus, clearly differentiate them from the conventional explosives. Here we present the RM preparation, calibration procedure and correlations attained between theoretical values and experimentally obtained results in laboratory conditions for C/O and N/C ratios of prepared hexogen (RDX), TNT, DLM2, TATP, cocaine, heroin, yperite, tetranitromethane, peroxide methylethylketone, nitromethane and ethyleneglycol dinitrate simulants. We have shown that analyses of the gamma ray spectra by using simple unfolding model developed for this purpose gave a nice agreement with the chemical formula of created simulants, thus the calibration quality was successfully tested.

New patient-controlled abdominal compression method in radiography: radiation dose and image quality.

PubMed

Piippo-Huotari, Oili; Norrman, Eva; Anderzén-Carlsson, Agneta; Geijer, Håkan

2018-05-01

The radiation dose for patients can be reduced with many methods and one way is to use abdominal compression. In this study, the radiation dose and image quality for a new patient-controlled compression device were compared with conventional compression and compression in the prone position . To compare radiation dose and image quality of patient-controlled compression compared with conventional and prone compression in general radiography. An experimental design with quantitative approach. After obtaining the approval of the ethics committee, a consecutive sample of 48 patients was examined with the standard clinical urography protocol. The radiation doses were measured as dose-area product and analyzed with a paired t-test. The image quality was evaluated by visual grading analysis. Four radiologists evaluated each image individually by scoring nine criteria modified from the European quality criteria for diagnostic radiographic images. There was no significant difference in radiation dose or image quality between conventional and patient-controlled compression. Prone position resulted in both higher dose and inferior image quality. Patient-controlled compression gave similar dose levels as conventional compression and lower than prone compression. Image quality was similar with both patient-controlled and conventional compression and was judged to be better than in the prone position.

Human Connectome Project Informatics: quality control, database services, and data visualization

PubMed Central

Marcus, Daniel S.; Harms, Michael P.; Snyder, Abraham Z.; Jenkinson, Mark; Wilson, J Anthony; Glasser, Matthew F.; Barch, Deanna M.; Archie, Kevin A.; Burgess, Gregory C.; Ramaratnam, Mohana; Hodge, Michael; Horton, William; Herrick, Rick; Olsen, Timothy; McKay, Michael; House, Matthew; Hileman, Michael; Reid, Erin; Harwell, John; Coalson, Timothy; Schindler, Jon; Elam, Jennifer S.; Curtiss, Sandra W.; Van Essen, David C.

2013-01-01

The Human Connectome Project (HCP) has developed protocols, standard operating and quality control procedures, and a suite of informatics tools to enable high throughput data collection, data sharing, automated data processing and analysis, and data mining and visualization. Quality control procedures include methods to maintain data collection consistency over time, to measure head motion, and to establish quantitative modality-specific overall quality assessments. Database services developed as customizations of the XNAT imaging informatics platform support both internal daily operations and open access data sharing. The Connectome Workbench visualization environment enables user interaction with HCP data and is increasingly integrated with the HCP's database services. Here we describe the current state of these procedures and tools and their application in the ongoing HCP study. PMID:23707591

DATA QUALITY OBJECTIVES AND MEASUREMENT QUALITY OBJECTIVES FOR RESEARCH PROJECTS

EPA Science Inventory

The paper provides assistance with systematic planning using measurement quality objectives to those working on research projects. These performance criteria are more familiar to researchers than data quality objectives because they are more closely associated with the measuremen...

7 CFR 58.733 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.733 Section 58.733... Procedures § 58.733 Quality control tests. (a) Chemical analyses. The following chemical analyses shall be... pasteurization by means of the phosphatase test, as well as any other tests necessary to assure good quality...

7 CFR 58.733 - Quality control tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Quality control tests. 58.733 Section 58.733... Procedures § 58.733 Quality control tests. (a) Chemical analyses. The following chemical analyses shall be... pasteurization by means of the phosphatase test, as well as any other tests necessary to assure good quality...

On stochastic control and optimal measurement strategies. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Kramer, L. C.

1971-01-01

The control of stochastic dynamic systems is studied with particular emphasis on those which influence the quality or nature of the measurements which are made to effect control. Four main areas are discussed: (1) the meaning of stochastic optimality and the means by which dynamic programming may be applied to solve a combined control/measurement problem; (2) a technique by which it is possible to apply deterministic methods, specifically the minimum principle, to the study of stochastic problems; (3) the methods described are applied to linear systems with Gaussian disturbances to study the structure of the resulting control system; and (4) several applications are considered.

Design, analysis, and interpretation of field quality-control data for water-sampling projects

USGS Publications Warehouse

Mueller, David K.; Schertz, Terry L.; Martin, Jeffrey D.; Sandstrom, Mark W.

2015-01-01

The report provides extensive information about statistical methods used to analyze quality-control data in order to estimate potential bias and variability in environmental data. These methods include construction of confidence intervals on various statistical measures, such as the mean, percentiles and percentages, and standard deviation. The methods are used to compare quality-control results with the larger set of environmental data in order to determine whether the effects of bias and variability might interfere with interpretation of these data. Examples from published reports are presented to illustrate how the methods are applied, how bias and variability are reported, and how the interpretation of environmental data can be qualified based on the quality-control analysis.

Advanced strategies for quality control of Chinese medicines.

PubMed

Zhao, Jing; Ma, Shuang-Cheng; Li, Shao-Ping

2018-01-05

Quality control is always the critical issue for Chinese medicines (CMs) with their worldwide increasing use. Different from western medicine, CMs are usually considered that multiple constituents are responsible for the therapeutic effects. Therefore, quality control of CMs is a challenge. In 2011, the strategies for quantification, related to the markers, reference compounds and approaches, in quality control of CMs were reviewed (Li, et al., J. Pharm. Biomed. Anal., 2011, 55, 802-809). Since then, some new strategies have been proposed in these fields. Therefore, the review on the strategies for quality control of CMs should be updated to improve the safety and efficacy of CMs. Herein, novel strategies related to quality marker discovery, reference compound development and advanced approaches (focused on glyco-analysis) for quality control, during 2011-2016, were summarized and discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

Machine Vision-Based Measurement Systems for Fruit and Vegetable Quality Control in Postharvest.

PubMed

Blasco, José; Munera, Sandra; Aleixos, Nuria; Cubero, Sergio; Molto, Enrique

Individual items of any agricultural commodity are different from each other in terms of colour, shape or size. Furthermore, as they are living thing, they change their quality attributes over time, thereby making the development of accurate automatic inspection machines a challenging task. Machine vision-based systems and new optical technologies make it feasible to create non-destructive control and monitoring tools for quality assessment to ensure adequate accomplishment of food standards. Such systems are much faster than any manual non-destructive examination of fruit and vegetable quality, thus allowing the whole production to be inspected with objective and repeatable criteria. Moreover, current technology makes it possible to inspect the fruit in spectral ranges beyond the sensibility of the human eye, for instance in the ultraviolet and near-infrared regions. Machine vision-based applications require the use of multiple technologies and knowledge, ranging from those related to image acquisition (illumination, cameras, etc.) to the development of algorithms for spectral image analysis. Machine vision-based systems for inspecting fruit and vegetables are targeted towards different purposes, from in-line sorting into commercial categories to the detection of contaminants or the distribution of specific chemical compounds on the product's surface. This chapter summarises the current state of the art in these techniques, starting with systems based on colour images for the inspection of conventional colour, shape or external defects and then goes on to consider recent developments in spectral image analysis for internal quality assessment or contaminant detection.

Measuring patient-perceived hospital service quality: a conceptual framework.

PubMed

Pai, Yogesh P; Chary, Satyanarayana T

2016-04-18

Purpose - Although measuring healthcare service quality is not a new phenomenon, the instruments used to measure are timeworn. With the shift in focus to patient centric processes in hospitals and recognizing healthcare to be different compared to other services, service quality measurement needs to be tuned specifically to healthcare. The purpose of this paper is to design a conceptual framework for measuring patient perceived hospital service quality (HSQ), based on existing service quality literature. Design/methodology/approach - Using HSQ theories, expanding existing healthcare service models and literature, a conceptual framework is proposed to measure HSQ. The paper outlines patient perceived service quality dimensions. Findings - An instrument for measuring HSQ dimensions is developed and compared with other service quality measuring instruments. The latest dimensions are in line with previous studies, but a relationship dimension is added. Practical implications - The framework empowers managers to assess healthcare quality in corporate, public and teaching hospitals. Originality/value - The paper helps academics and practitioners to assess HSQ from a patient perspective.

30 CFR 28.30 - Quality control plans; filing requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality control plans; filing requirements. 28... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.30 Quality control plans; filing... part, each applicant shall file with MSHA a proposed quality control plan which shall be designed to...

30 CFR 28.30 - Quality control plans; filing requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality control plans; filing requirements. 28... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.30 Quality control plans; filing... part, each applicant shall file with MSHA a proposed quality control plan which shall be designed to...

30 CFR 28.30 - Quality control plans; filing requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.30 Quality control plans; filing... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quality control plans; filing requirements. 28... part, each applicant shall file with MSHA a proposed quality control plan which shall be designed to...

30 CFR 28.30 - Quality control plans; filing requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.30 Quality control plans; filing... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quality control plans; filing requirements. 28... part, each applicant shall file with MSHA a proposed quality control plan which shall be designed to...

30 CFR 28.30 - Quality control plans; filing requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.30 Quality control plans; filing... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality control plans; filing requirements. 28... part, each applicant shall file with MSHA a proposed quality control plan which shall be designed to...

Quality Measures for the Care of Patients with Insomnia

PubMed Central

Edinger, Jack D.; Buysse, Daniel J.; Deriy, Ludmila; Germain, Anne; Lewin, Daniel S.; Ong, Jason C.; Morgenthaler, Timothy I.

2015-01-01

The American Academy of Sleep Medicine (AASM) commissioned five Workgroups to develop quality measures to optimize management and care for patients with common sleep disorders including insomnia. Following the AASM process for quality measure development, this document describes measurement methods for two desirable outcomes of therapy, improving sleep quality or satisfaction, and improving daytime function, and for four processes important to achieving these goals. To achieve the outcome of improving sleep quality or satisfaction, pre- and post-treatment assessment of sleep quality or satisfaction and providing an evidence-based treatment are recommended. To realize the outcome of improving daytime functioning, pre- and post-treatment assessment of daytime functioning, provision of an evidence-based treatment, and assessment of treatment-related side effects are recommended. All insomnia measures described in this report were developed by the Insomnia Quality Measures Workgroup and approved by the AASM Quality Measures Task Force and the AASM Board of Directors. The AASM recommends the use of these measures as part of quality improvement programs that will enhance the ability to improve care for patients with insomnia. Citation: Edinger JD, Buysse DJ, Deriy L, Germain A, Lewin DS, Ong JC, Morgenthaler TI. Quality measures for the care of patients with insomnia. J Clin Sleep Med 2015;11(3):311–334. PMID:25700881

21 CFR 864.8625 - Hematology quality control mixture.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hematology quality control mixture. 864.8625 Section 864.8625 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... quality control mixture. (a) Identification. A hematology quality control mixture is a device used to...

Innovative United Kingdom Approaches To Measuring Service Quality.

ERIC Educational Resources Information Center

Winkworth, Ian

2001-01-01

Reports on approaches to measuring the service quality of academic libraries in the United Kingdom. Discusses the role of government and the national background of quality measurement; measurement frameworks; better use of statistics; benchmarking; measuring user satisfaction; and possible future development. (Author/LRW)

Using Clinical Data Standards to Measure Quality: A New Approach.

PubMed

D'Amore, John D; Li, Chun; McCrary, Laura; Niloff, Jonathan M; Sittig, Dean F; McCoy, Allison B; Wright, Adam

2018-04-01

 Value-based payment for care requires the consistent, objective calculation of care quality. Previous initiatives to calculate ambulatory quality measures have relied on billing data or individual electronic health records (EHRs) to calculate and report performance. New methods for quality measure calculation promoted by federal regulations allow qualified clinical data registries to report quality outcomes based on data aggregated across facilities and EHRs using interoperability standards.  This research evaluates the use of clinical document interchange standards as the basis for quality measurement.  Using data on 1,100 patients from 11 ambulatory care facilities and 5 different EHRs, challenges to quality measurement are identified and addressed for 17 certified quality measures.  Iterative solutions were identified for 14 measures that improved patient inclusion and measure calculation accuracy. Findings validate this approach to improving measure accuracy while maintaining measure certification.  Organizations that report care quality should be aware of how identified issues affect quality measure selection and calculation. Quality measure authors should consider increasing real-world validation and the consistency of measure logic in respect to issues identified in this research. Schattauer GmbH Stuttgart.

Cellular Strategies of Protein Quality Control

PubMed Central

Chen, Bryan; Retzlaff, Marco; Roos, Thomas; Frydman, Judith

2011-01-01

Eukaryotic cells must contend with a continuous stream of misfolded proteins that compromise the cellular protein homeostasis balance and jeopardize cell viability. An elaborate network of molecular chaperones and protein degradation factors continually monitor and maintain the integrity of the proteome. Cellular protein quality control relies on three distinct yet interconnected strategies whereby misfolded proteins can either be refolded, degraded, or delivered to distinct quality control compartments that sequester potentially harmful misfolded species. Molecular chaperones play a critical role in determining the fate of misfolded proteins in the cell. Here, we discuss the spatial and temporal organization of cellular quality control strategies and their implications for human diseases linked to protein misfolding and aggregation. PMID:21746797

21 CFR 211.22 - Responsibilities of quality control unit.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 4 2011-04-01 2011-04-01 false Responsibilities of quality control unit. 211.22... Personnel § 211.22 Responsibilities of quality control unit. (a) There shall be a quality control unit that... have been fully investigated. The quality control unit shall be responsible for approving or rejecting...

21 CFR 211.22 - Responsibilities of quality control unit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Responsibilities of quality control unit. 211.22... Personnel § 211.22 Responsibilities of quality control unit. (a) There shall be a quality control unit that... have been fully investigated. The quality control unit shall be responsible for approving or rejecting...

40 CFR 81.112 - Charleston Intrastate Air Quality Control Region.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Quality Control Regions § 81.112 Charleston Intrastate Air Quality Control Region. The Charleston Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... Quality Control Region: Region 1. 81.107Greenwood Intrastate Air Quality Control Region: Region 2. 81...

40 CFR 81.112 - Charleston Intrastate Air Quality Control Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Quality Control Regions § 81.112 Charleston Intrastate Air Quality Control Region. The Charleston Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... Quality Control Region: Region 1. 81.107Greenwood Intrastate Air Quality Control Region: Region 2. 81...

Quantitative comparison of measurements of urgent care service quality.

PubMed

Qin, Hong; Prybutok, Victor; Prybutok, Gayle

2016-01-01

Service quality and patient satisfaction are essential to health care organization success. Parasuraman, Zeithaml, and Berry introduced SERVQUAL, a prominent service quality measure not yet applied to urgent care. We develop an instrument to measure perceived service quality and identify the determinants of patient satisfaction/ behavioral intentions. We examine the relationships among perceived service quality, patient satisfaction and behavioral intentions, and demonstrate that urgent care service quality is not equivalent using measures of perceptions only, differences of expectations minus perceptions, ratio of perceptions to expectations, and the log of the ratio. Perceptions provide the best measure of urgent care service quality.

Quality Measures for the Care of Patients with Narcolepsy

PubMed Central

Krahn, Lois E.; Hershner, Shelley; Loeding, Lauren D.; Maski, Kiran P.; Rifkin, Daniel I.; Selim, Bernardo; Watson, Nathaniel F.

2015-01-01

The American Academy of Sleep Medicine (AASM) commissioned a Workgroup to develop quality measures for the care of patients with narcolepsy. Following a comprehensive literature search, 306 publications were found addressing quality care or measures. Strength of association was graded between proposed process measures and desired outcomes. Following the AASM process for quality measure development, we identified three outcomes (including one outcome measure) and seven process measures. The first desired outcome was to reduce excessive daytime sleepiness by employing two process measures: quantifying sleepiness and initiating treatment. The second outcome was to improve the accuracy of diagnosis by employing the two process measures: completing both a comprehensive sleep history and an objective sleep assessment. The third outcome was to reduce adverse events through three steps: ensuring treatment follow-up, documenting medical comorbidities, and documenting safety measures counseling. All narcolepsy measures described in this report were developed by the Narcolepsy Quality Measures Work-group and approved by the AASM Quality Measures Task Force and the AASM Board of Directors. The AASM recommends the use of these measures as part of quality improvement programs that will enhance the ability to improve care for patients with narcolepsy. Citation: Krahn LE, Hershner S, Loeding LD, Maski KP, Rifkin DI, Selim B, Watson NF. Quality measures for the care of patients with narcolepsy. J Clin Sleep Med 2015;11(3):335–355. PMID:25700880

7 CFR 275.21 - Quality control review reports.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 4 2011-01-01 2011-01-01 false Quality control review reports. 275.21 Section 275.21... Reporting on Program Performance § 275.21 Quality control review reports. (a) General. Each State agency shall submit reports on the performance of quality control reviews in accordance with the requirements...

Online devices and measuring systems for the automatic control of newspaper printing

NASA Astrophysics Data System (ADS)

Marszalec, Elzbieta A.; Heikkila, Ismo; Juhola, Helene; Lehtonen, Tapio

1999-09-01

The paper reviews the state-of-the-art color measuring systems used for the control of newspaper printing. The printing process requirements are specified and different off-line and on-line color quality control systems, commercially available and under development, are evaluated. Recent market trends in newspaper printing are discussed based on the survey. The study was made on information derived from: conference proceedings (TAGA, IARIGAI, SPIE and IS&T), journals (American Printer, Applied Optics), discussions with experts (GMI, QTI, HONEYWELL, TOBIAS, GretagMacbeth), IFRA Expo'98/Quality Measuring Technologies, commercial brochures, and the Internet. On the background of this review, three different measuring principles, currently, under investigation at VTT Information Technology, are described and their applicability to newspaper printing is evaluated.

International Airline Quality Measurement

DOT National Transportation Integrated Search

1998-01-01

Historically, airline quality has been measured through the use of surveys that ask the consumers to make a comparison between expectations and outcomes. This method was informative but very cumbersome in a rapidly changing environment. This paper ou...

Adopting software quality measures for healthcare processes.

PubMed

Yildiz, Ozkan; Demirörs, Onur

2009-01-01

In this study, we investigated the adoptability of software quality measures for healthcare process measurement. Quality measures of ISO/IEC 9126 are redefined from a process perspective to build a generic healthcare process quality measurement model. Case study research method is used, and the model is applied to a public hospital's Entry to Care process. After the application, weak and strong aspects of the process can be easily observed. Access audibility, fault removal, completeness of documentation, and machine utilization are weak aspects and these aspects are the candidates for process improvement. On the other hand, functional completeness, fault ratio, input validity checking, response time, and throughput time are the strong aspects of the process.

Chief Complaint-Based Performance Measures: A New Focus For Acute Care Quality Measurement

PubMed Central

Griffey, Richard T; Pines, Jesse M.; Farley, Heather L.; Phelan, Michael P; Beach, Christopher; Schuur, Jeremiah D; Venkatesh, Arjun K.

2014-01-01

Performance measures are increasingly important to guide meaningful quality improvement efforts and value-based reimbursement. Populations included in most current hospital performance measures are defined by recorded diagnoses using International Disease Classification (ICD)-9 codes in administrative claims data. While the diagnosis-centric approach allows the assessment of disease-specific quality, it fails to measure one of the primary functions of emergency department (ED) care which involves diagnosing, risk-stratifying, and treating patients’ potentially life-threatening conditions based on symptoms (i.e. chief complaints). In this paper we propose chief complaint-based quality measures as a means to enhance the evaluation of quality and value in emergency care. We discuss the potential benefits of chief-complaint based measures, describe opportunities to mitigate challenges, propose an example measure set, and present several recommendations to advance this paradigm in ED-based performance measurement. PMID:25443989

40 CFR 81.88 - Billings Intrastate Air Quality Control Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Quality Control Regions § 81.88 Billings Intrastate Air Quality Control Region. The Metropolitan Billings Intrastate Air Quality Control Region (Montana) has been renamed the Billings Intrastate Air Quality Control... to by Montana authorities as follows: Sec. 481.168Great Falls Intrastate Air Quality Control Region...

40 CFR 81.88 - Billings Intrastate Air Quality Control Region.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Quality Control Regions § 81.88 Billings Intrastate Air Quality Control Region. The Metropolitan Billings Intrastate Air Quality Control Region (Montana) has been renamed the Billings Intrastate Air Quality Control... to by Montana authorities as follows: Sec. 481.168Great Falls Intrastate Air Quality Control Region...

An approach to measuring the quality of breast cancer decisions.

PubMed

Sepucha, Karen; Ozanne, Elissa; Silvia, Kerry; Partridge, Ann; Mulley, Albert G

2007-02-01

To explore an approach to measuring the quality of decisions made in the treatment of early stage breast cancer, focusing on patients' decision-specific knowledge and the concordance between patients' stated preferences for treatment outcomes and treatment received. Candidate knowledge and value items were identified after an extensive review of the published literature as well as reports on 27 focus groups and 46 individual interviews with breast cancer survivors. Items were subjected to cognitive interviews with six additional patients. A preliminary decision quality measure consisting of five knowledge items and four value items was pilot tested with 35 breast cancer survivors who also completed the control preferences scale and the decisional conflict scale (DCS). Preference for control and knowledge did not vary by treatment. The mean of the participants' knowledge scores was 54%. There was no correlation between the knowledge scores and the informed subscale of the DCS (Pearson r = .152, n = 32, p = 0.408). Patients who preferred to keep their breast were over five times as likely to have breast-conserving surgery than those who did not (OR 5.33, 95% CI (1.2, 24.5), p = 0.06). Patients who wanted to avoid radiation were six times as likely to choose mastectomy than those who did not (OR 6.4, 95% CI (1.34, 30.61), p = 0.04). Measuring decision quality by assessing patients' decision-specific knowledge and concordance between their values and treatment received, is feasible and important. Further work is necessary to overcome the methodological challenges identified in this pilot work. Guidelines for early stage breast cancer emphasize the importance of including patients' preferences in decisions about treatment. The ability of doctors and patients to make decisions that reflect the considered preferences of well-informed patients can and should be measured.

Assessing relationship quality in mandated community treatment: blending care with control.

PubMed

Skeem, Jennifer L; Louden, Jennifer Eno; Polaschek, Devon; Camp, Jacqueline

2007-12-01

Traditional measures of the therapeutic alliance do not capture the dual roles inherent in relationships with involuntary clients. Providers not only care for, but also have control over, involuntary clients. In 2 studies of probationers mandated to psychiatric treatment (n=90; n=322), the authors developed and validated the revised Dual-Role Relationships Inventory (DRI-R). The authors found that (a) relationship quality in mandated treatment involves caring and fairness, trust, and an authoritative (not authoritarian) style, (b) the DRI-R assesses these domains of relationship quality, is internally consistent, and relates in a theoretically coherent pattern with ratings of within-session behavior and with measures of the therapeutic alliance, relationship satisfaction, symptoms, and treatment motivation, and (c) the quality of dual-role relationships predicts future compliance with the rules, as assessed by probation violations and revocation. The DRI-R covaries with multiple domains more strongly than a leading measure of the therapeutic alliance, suggesting that it better captures the nature and effect of relationship quality in mandated treatment.

[Advances in the use of instrumental measurement of colour in the development, production and quality control of drugs, medicinal preparations and pharmaceutical auxiliary substances I ].

PubMed

Subert, Jan; Cižmárik, Jozef

2013-04-01

Colour is one of the important indices of the quality of drugs, medicinal preparations and pharmaceutical auxiliary substances. The paper summarizes the development and use of instrumental measurement of colour in pharmacy in recent ten years focusing on the drugs of synthetic origin and pharmaceutical auxiliary substances including their control.

Control Measure Dataset

EPA Pesticide Factsheets

The EPA Control Measure Dataset is a collection of documents describing air pollution control available to regulated facilities for the control and abatement of air pollution emissions from a range of regulated source types, whether directly through the use of technical measures, or indirectly through economic or other measures.

The importance of quality control in validating concentrations ...

EPA Pesticide Factsheets

A national-scale survey of 247 contaminants of emerging concern (CECs), including organic and inorganic chemical compounds, and microbial contaminants, was conducted in source and treated drinking water samples from 25 treatment plants across the United States. Multiple methods were used to determine these CECs, including six analytical methods to measure 174 pharmaceuticals, personal care products, and pesticides. A three-component quality assurance/quality control (QA/QC) program was designed for the subset of 174 CECs which allowed us to assess and compare performances of the methods used. The three components included: 1) a common field QA/QC protocol and sample design, 2) individual investigator-developed method-specific QA/QC protocols, and 3) a suite of 46 method comparison analytes that were determined in two or more analytical methods. Overall method performance for the 174 organic chemical CECs was assessed by comparing spiked recoveries in reagent, source, and treated water over a two-year period. In addition to the 247 CECs reported in the larger drinking water study, another 48 pharmaceutical compounds measured did not consistently meet predetermined quality standards. Methodologies that did not seem suitable for these analytes are overviewed. The need to exclude analytes based on method performance demonstrates the importance of additional QA/QC protocols. This paper compares the method performance of six analytical methods used to measure 174 emer

Nurse Reported Quality of Care: A Measure of Hospital Quality

PubMed Central

McHugh, Matthew D.; Stimpfel, Amy Witkoski

2013-01-01

As the primary providers of round-the-clock bedside care, nurses are well positioned to report on hospital quality of care. Researchers have not examined how nurses’ reports of quality correspond with standard process or outcomes measures of quality. We assess the validity of evaluating hospital quality by aggregating hospital nurses’ responses to a single item that asks them to report on quality of care. We found that a 10% increment in the proportion of nurses reporting excellent quality of care was associated with lower odds of mortality and failure to rescue; greater patient satisfaction; and higher composite process of care scores for acute myocardial infarction, pneumonia, and surgical patients. Nurse reported quality of care is a useful indicator of hospital performance. PMID:22911102

Quality Measures in Stroke

PubMed Central

Poisson, Sharon N.; Josephson, S. Andrew

2011-01-01

Stroke is a major public health burden, and accounts for many hospitalizations each year. Due to gaps in practice and recommended guidelines, there has been a recent push toward implementing quality measures to be used for improving patient care, comparing institutions, as well as for rewarding or penalizing physicians through pay-for-performance. This article reviews the major organizations involved in implementing quality metrics for stroke, and the 10 major metrics currently being tracked. We also discuss possible future metrics and the implications of public reporting and using metrics for pay-for-performance. PMID:23983840

Development of a quality control test procedure for characterizing fracture properties of asphalt mixtures.

DOT National Transportation Integrated Search

2011-06-01

The main objective of this study is to investigate the use of the semi-circular bend (SCB) : test as a quality assurance/quality control (QA/QC) measure for field construction. : Comparison of fracture properties from the SCB test and fatigue beam te...

Measuring up: Implementing a dental quality measure in the electronic health record context.

PubMed

Bhardwaj, Aarti; Ramoni, Rachel; Kalenderian, Elsbeth; Neumann, Ana; Hebballi, Nutan B; White, Joel M; McClellan, Lyle; Walji, Muhammad F

2016-01-01

Quality improvement requires using quality measures that can be implemented in a valid manner. Using guidelines set forth by the Meaningful Use portion of the Health Information Technology for Economic and Clinical Health Act, the authors assessed the feasibility and performance of an automated electronic Meaningful Use dental clinical quality measure to determine the percentage of children who received fluoride varnish. The authors defined how to implement the automated measure queries in a dental electronic health record. Within records identified through automated query, the authors manually reviewed a subsample to assess the performance of the query. The automated query results revealed that 71.0% of patients had fluoride varnish compared with the manual chart review results that indicated 77.6% of patients had fluoride varnish. The automated quality measure performance results indicated 90.5% sensitivity, 90.8% specificity, 96.9% positive predictive value, and 75.2% negative predictive value. The authors' findings support the feasibility of using automated dental quality measure queries in the context of sufficient structured data. Information noted only in free text rather than in structured data would require using natural language processing approaches to effectively query electronic health records. To participate in self-directed quality improvement, dental clinicians must embrace the accountability era. Commitment to quality will require enhanced documentation to support near-term automated calculation of quality measures. Copyright © 2016 American Dental Association. Published by Elsevier Inc. All rights reserved.

7 CFR 58.141 - Alternate quality control program.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Alternate quality control program. 58.141 Section 58... Service 1 Quality Specifications for Raw Milk § 58.141 Alternate quality control program. When a plant has in operation an acceptable quality program, at the producer level, which is approved by the...

21 CFR 111.105 - What must quality control personnel do?

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 2 2011-04-01 2011-04-01 false What must quality control personnel do? 111.105... for Quality Control § 111.105 What must quality control personnel do? Quality control personnel must... manufacturing record. To do so, quality control personnel must perform operations that include: (a) Approving or...

Theoretical approach to society-wide environmental quality control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayano, K.

1982-01-01

The study outlines the basis for a theory of societal control of environmental quality in the US based on the concepts and philosophy of company-wide quality control which has developed in Japan as a cross-disciplinary approach to problem-solving in the industrial realm. The basic concepts are: 1) every member of society, as a producer of environmental products and services for future generations, in principle has the responsibility to control the quality of his output; 2) environment quality is the quality of life, or the fitness of use of environment for humans; and 3) societal control is any activity necessary formore » quality production of environmental products and services continuously or in the long run. A motivator-hygiene theory of environmental quality is identified, and a proposal is made that the policy provision must be formulated differently between those aimed at hygiene factors of environmental quality and those aimed at motivators, the former in a collectivistic manner, the latter as an individual problem. The concept of societal cost of environmental quality is introduced. Based on the motivator-hygiene theory of environmental quality, the collectivistic and individual approaches are differentiated and discussed.« less

Effectiveness of transportation control measures : overview of the state of the practice.

DOT National Transportation Integrated Search

1996-01-01

Transportation control measures, or TCMs, are transportation measures or strategies intended both to reduce vehicle miles of travel (VMT) and to make those traveled more efficient. Although the term TCM has its origins in air quality and emissions re...

Traffic Data Quality Measurement : Final Report

DOT National Transportation Integrated Search

2004-09-15

One of the foremost recommendations from the FHWA sponsored workshops on Traffic Data Quality (TDQ) in 2003 was a call for "guidelines and standards for calculating data quality measures." These guidelines and standards are expected to contain method...

Human voice quality measurement in noisy environments.

PubMed

Ueng, Shyh-Kuang; Luo, Cheng-Ming; Tsai, Tsung-Yu; Yeh, Hsuan-Chen

2015-01-01

Computerized acoustic voice measurement is essential for the diagnosis of vocal pathologies. Previous studies showed that ambient noises have significant influences on the accuracy of voice quality assessment. This paper presents a voice quality assessment system that can accurately measure qualities of voice signals, even though the input voice data are contaminated by low-frequency noises. The ambient noises in our living rooms and laboratories are collected and the frequencies of these noises are analyzed. Based on the analysis, a filter is designed to reduce noise level of the input voice signal. Then, improved numerical algorithms are employed to extract voice parameters from the voice signal to reveal the health of the voice signal. Compared with MDVP and Praat, the proposed method outperforms these two widely used programs in measuring fundamental frequency and harmonic-to-noise ratio, and its performance is comparable to these two famous programs in computing jitter and shimmer. The proposed voice quality assessment method is resistant to low-frequency noises and it can measure human voice quality in environments filled with noises from air-conditioners, ceiling fans and cooling fans of computers.

Randomized Controlled Pilot Trial of Yoga in Overweight and Obese Breast Cancer Survivors: Effects on Quality of Life and Anthropometric Measures

PubMed Central

Littman, Alyson J; Bertram, Lisa Cadmus; Ceballos, Rachel; Ulrich, Cornelia M; Ramaprasad, Jaya; McGregor, Bonnie; McTiernan, Anne

2011-01-01

PURPOSE To obtain estimates of time to recruit the study sample, retention, facility-based class attendance and home practice for a study of yoga in breast cancer survivors, and its efficacy on fatigue, quality of life (QOL), and weight change. METHODS Sixty-three post-treatment stage 0–III borderline overweight and obese (body mass index ≥ 24 kg/m2) breast cancer survivors were randomly assigned to a 6-month, facility- and home-based viniyoga intervention (n = 32) or a waitlist control group (n = 31). The yoga goal was 5 practices per week. Primary outcome measures were changes in self-reported QOL, fatigue, and weight from baseline to 6 months. Secondary outcomes included changes in waist and hip circumference. RESULTS It took 12 months to complete recruitment. Participants attended a mean of 19.6 classes and practiced at home a mean of 55.8 times during the 6-month period. At follow-up, 90% of participants completed questionnaires and 87% completed anthropometric measurements. QOL and fatigue improved to a greater extent among women in the yoga group relative to women in the control group, although no differences were statistically significant. Waist circumference decreased 3.1 cm (95% CI: −5.7, −0.4) more among women in the yoga compared with the control group, with no differences in weight change. CONCLUSIONS This study provides important information regarding recruitment, retention, and practice levels achieved during a 6-month, intensive yoga intervention in overweight and obese breast cancer survivors. Yoga may help decrease waist circumference and improve quality of life; future studies are needed to confirm these results. PMID:21207071

Issues in Measuring and Improving Health Care Quality

PubMed Central

Friedman, Maria A.

1995-01-01

This issue of the Health Care Financing Review focuses on issues and advances in measuring and improving the quality of care, particularly for Medicare and Medicaid beneficiaries. Discussions of quality-related topics are especially timely, given the growing and widespread interest in improving quality in the organization, financing, and delivery of health care services. This article has several purposes. The first is to provide a brief description of some of the causes underlying the growth of the health care quality movement; the second is to provide a contextual framework for discussion of some of the overarching themes that emerge in this issue. These themes include examining conceptual issues, developing quality measures for specific sites and populations, and creating or adapting data sets for quality-measurement purposes. PMID:10151882

Sci-Fri AM: Quality, Safety, and Professional Issues 01: CPQR Technical Quality Control Suite Development including Quality Control Workload Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malkoske, Kyle; Nielsen, Michelle; Brown, Erika

A close partnership between the Canadian Partnership for Quality Radiotherapy (CPQR) and the Canadian Organization of Medical Physicist’s (COMP) Quality Assurance and Radiation Safety Advisory Committee (QARSAC) has resulted in the development of a suite of Technical Quality Control (TQC) Guidelines for radiation treatment equipment, that outline specific performance objectives and criteria that equipment should meet in order to assure an acceptable level of radiation treatment quality. The framework includes consolidation of existing guidelines and/or literature by expert reviewers, structured stages of public review, external field-testing and ratification by COMP. The adopted framework for the development and maintenance of themore » TQCs ensures the guidelines incorporate input from the medical physics community during development, measures the workload required to perform the QC tests outlined in each TQC, and remain relevant (i.e. “living documents”) through subsequent planned reviews and updates. This presentation will show the Multi-Leaf Linear Accelerator document as an example of how feedback and cross-national work to achieve a robust guidance document. During field-testing, each technology was tested at multiple centres in a variety of clinic environments. As part of the defined feedback, workload data was captured. This lead to average time associated with testing as defined in each TQC document. As a result, for a medium-sized centre comprising 6 linear accelerators and a comprehensive brachytherapy program, we evaluate the physics workload to 1.5 full-time equivalent physicist per year to complete all QC tests listed in this suite.« less

Quality-Assurance/Quality-Control Manual for Collection and Analysis of Water-Quality Data in the Ohio District, US Geological Survey

USGS Publications Warehouse

Francy, D.S.; Jones, A.L.; Myers, Donna N.; Rowe, G.L.; Eberle, Michael; Sarver, K.M.

1998-01-01

The U.S. Geological Survey (USGS), Water Resources Division (WRD), requires that quality-assurance/quality-control (QA/QC) activities be included in any sampling and analysis program. Operational QA/QC procedures address local needs while incorporating national policies. Therefore, specific technical policies were established for all activities associated with water-quality project being done by the Ohio District. The policies described in this report provide Ohio District personnel, cooperating agencies, and others with a reference manual on QA/QC procedures that are followed in collecitng and analyzing water-quality samples and reporting water-quality information in the Ohio District. The project chief, project support staff, District Water-Quality Specialist, and District Laboratory Coordinator are all involved in planning and implementing QA/QC activities at the district level. The District Chief and other district-level managers provide oversight, and the Regional Water-Quality Specialist, Office of Water Quality (USGS headquarters), and the Branch of Quality Systems within the Office of Water Quality create national QA/QC polices and provide assistance to District personnel. In the literature, the quality of all measurement data is expressed in terms of precision, variability, bias, accuracy, completeness, representativeness, and comparability. In the Ohio District, bias and variability will be used to describe quality-control data generated from samples in the field and laboratory. Each project chief must plan for implementation and financing of QA/QC activities necessary to achieve data-quality objectives. At least 15 percent of the total project effort must be directed toward QA/QC activities. Of this total, 5-10 percent will be used for collection and analysis of quality-control samples. This is an absolute minimum, and more may be required based on project objectives. Proper techniques must be followed in the collection and processing of surface

Quality control method to measure predator evasion in wild and mass-reared Mediterranean fruit flies (Diptera: Tephritidae)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hendrichs, M.; Wornoayporn, V.; Hendrichs, J.

Sterile male insects, mass-reared and released as part of sterile insect technique (SIT) programs, must survive long enough in the field to mature sexually and compete effectively with wild males for wild females. An often reported problem in Mediterranean fruit fly (medfly) Ceratitis capitata (Wiedemann) SIT programs is that numbers of released sterile males decrease rapidly in the field for various reasons, including losses to different types of predators. This is a serious issue in view that most operational programs release sterile flies at an age when they are still immature. Previous field and field-cage tests have confirmed that fliesmore » of laboratory strains are less able to evade predators than wild flies. Such tests involve, however, considerable manipulation and observation of predators and are therefore not suitable for routine measurements of predator evasion. Here we describe a simple quality control method with aspirators to measure agility in medflies and show that this parameter is related to the capacity of flies to evade predators. Although further standardization of the test is necessary to allow more accurate inter-strain comparisons, results confirm the relevance of measuring predator evasion in mass-reared medfly strains. Besides being a measure of this sterile male quality parameter, the described method could be used for the systematic selection of strains with a higher capacity for predator evasion. (author) [Spanish] Insectos machos esteriles criados en forma masiva para ser liberados en programas que utilizan la tecnica del insecto esteril (TIE), tienen que tener la capacidad de sobrevivir en el campo el tiempo necesario para poder madurar sexualmente y competir efectivamente con los machos silvestres por hembras silvestres. Un problema frecuentemente reportado por dichos programas de la mosca del Mediterraneo, Ceratitis capitata (Wiedemann), es que el numero de machos esteriles de laboratorio liberados en el campo, decrecen

Quality Control in Higher Education.

ERIC Educational Resources Information Center

Hogarth, Charles P.

The status of quality control in U.S. higher education is discussed with an overview of the functions and structure of public and private colleges and universities. The book is divided into seven chapters: (1) outside controls (accrediting groups, governmental groups and other groups); (2) structure (board of control, president, organization); (3)…

Standardisation of DNA quantitation by image analysis: quality control of instrumentation.

PubMed

Puech, M; Giroud, F

1999-05-01

DNA image analysis is frequently performed in clinical practice as a prognostic tool and to improve diagnosis. The precision of prognosis and diagnosis depends on the accuracy of analysis and particularly on the quality of image analysis systems. It has been reported that image analysis systems used for DNA quantification differ widely in their characteristics (Thunissen et al.: Cytometry 27: 21-25, 1997). This induces inter-laboratory variations when the same sample is analysed in different laboratories. In microscopic image analysis, the principal instrumentation errors arise from the optical and electronic parts of systems. They bring about problems of instability, non-linearity, and shading and glare phenomena. The aim of this study is to establish tools and standardised quality control procedures for microscopic image analysis systems. Specific reference standard slides have been developed to control instability, non-linearity, shading and glare phenomena and segmentation efficiency. Some systems have been controlled with these tools and these quality control procedures. Interpretation criteria and accuracy limits of these quality control procedures are proposed according to the conclusions of a European project called PRESS project (Prototype Reference Standard Slide). Beyond these limits, tested image analysis systems are not qualified to realise precise DNA analysis. The different procedures presented in this work determine if an image analysis system is qualified to deliver sufficiently precise DNA measurements for cancer case analysis. If the controlled systems are beyond the defined limits, some recommendations are given to find a solution to the problem.

Simple measurement-based admission control for DiffServ access networks

NASA Astrophysics Data System (ADS)

Lakkakorpi, Jani

2002-07-01

In order to provide good Quality of Service (QoS) in a Differentiated Services (DiffServ) network, a dynamic admission control scheme is definitely needed as an alternative to overprovisioning. In this paper, we present a simple measurement-based admission control (MBAC) mechanism for DiffServ-based access networks. Instead of using active measurements only or doing purely static bookkeeping with parameter-based admission control (PBAC), the admission control decisions are based on bandwidth reservations and periodically measured & exponentially averaged link loads. If any link load on the path between two endpoints is over the applicable threshold, access is denied. Link loads are periodically sent to Bandwidth Broker (BB) of the routing domain, which makes the admission control decisions. The information needed in calculating the link loads is retrieved from the router statistics. The proposed admission control mechanism is verified through simulations. Our results prove that it is possible to achieve very high bottleneck link utilization levels and still maintain good QoS.

Quality Control Technician.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. Center on Education and Training for Employment.

This document contains 18 units to consider for use in a tech prep competency profile for the occupation of quality control technician. All the units listed will not necessarily apply to every situation or tech prep consortium, nor will all the competencies within each unit be appropriate. Several units appear within each specific occupation and…

Dental Quality Measurement--A Practitioner Perspective.

PubMed

Amundson, Craig W

2016-04-01

This article reviews the HealthPartners Dental Group's experience with clinical quality measurement and provides information on the administrative infrastructure that supports measurement within the group. Some examples of the role measurement plays in operations and clinical practice are also reviewed.

CHALLENGES IN SETTING UP QUALITY CONTROL IN DIAGNOSTIC RADIOLOGY FACILITIES IN NIGERIA.

PubMed

Inyang, S O; Egbe, N O; Ekpo, E

2015-01-01

The Nigerian Nuclear Regulatory Authority (NNRA) was established to regulate and control the use of radioactive and radiation emitting sources in Nigeria. Quality control (QC) on diagnostic radiology equipment form part of the fundamental requirements for the authorization of diagnostic radiology facilities in the Country. Some quality control tests (output, exposure linearity and reproducibility) were measured on the x-ray machines in the facilities that took part in the study. Questionnaire was developed to evaluate the frequencies at which QC tests were conducted in the facilities and the challenges in setting up QC. Results show great variation in the values of the QC parameters measured. Inadequate cooperation by facilities management, lack of QC equipment and insufficient staff form the major challenges in setting up QC in the facilities under study. The responses on the frequencies at which QC tests should be conducted did not correspond to the recommended standards; indicating that personnel were not familiar with QC implementation and may require further training on QC.

40 CFR 81.77 - Puerto Rico Air Quality Control Region.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Puerto Rico Air Quality Control Region... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.77 Puerto Rico Air Quality Control Region. The Puerto Rico Air Quality Control Region...

40 CFR 81.77 - Puerto Rico Air Quality Control Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Puerto Rico Air Quality Control Region... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.77 Puerto Rico Air Quality Control Region. The Puerto Rico Air Quality Control Region...

40 CFR 81.77 - Puerto Rico Air Quality Control Region.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 18 2012-07-01 2012-07-01 false Puerto Rico Air Quality Control Region... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.77 Puerto Rico Air Quality Control Region. The Puerto Rico Air Quality Control Region...

40 CFR 81.77 - Puerto Rico Air Quality Control Region.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 18 2013-07-01 2013-07-01 false Puerto Rico Air Quality Control Region... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.77 Puerto Rico Air Quality Control Region. The Puerto Rico Air Quality Control Region...

Looking beyond patients: Can parents' quality of life predict asthma control in children?

PubMed

Cano-Garcinuño, Alfredo; Mora-Gandarillas, Isabel; Bercedo-Sanz, Alberto; Callén-Blecua, María Teresa; Castillo-Laita, José Antonio; Casares-Alonso, Irene; Forns-Serrallonga, Dolors; Tauler-Toro, Eulàlia; Alonso-Bernardo, Luz María; García-Merino, Águeda; Moneo-Hernández, Isabel; Cortés-Rico, Olga; Carvajal-Urueña, Ignacio; Morell-Bernabé, Juan José; Martín-Ibáñez, Itziar; Rodríguez-Fernández-Oliva, Carmen Rosa; Asensi-Monzó, María Teresa; Fernández-Carazo, Carmen; Murcia-García, José; Durán-Iglesias, Catalina; Montón-Álvarez, José Luis; Domínguez-Aurrecoechea, Begoña; Praena-Crespo, Manuel

2016-07-01

Social and family factors may influence the probability of achieving asthma control in children. Parents' quality of life has been insufficiently explored as a predictive factor linked to the probability of achieving disease control in asthmatic children. Determine whether the parents' quality of life predicts medium-term asthma control in children. Longitudinal study of children between 4 and 14 years of age, with active asthma. The parents' quality of life was evaluated using the specific IFABI-R instrument, in which scores were higher for poorer quality of life. Its association with asthma control measures in the child 16 weeks later was analyzed using multivariate methods, adjusting the effect for disease, child and family factors. The data from 452 children were analyzed (median age 9.6 years, 63.3% males). The parents' quality of life was predictive for asthma control; each point increase on the initial IFABI-R score was associated with an adjusted odds ratio (95% confidence interval) of 0.56 (0.37-0.86) for good control of asthma on the second visit, 2.58 (1.62-4.12) for asthma exacerbation, 2.12 (1.33-3.38) for an unscheduled visit to the doctor, and 2.46 (1.18-5.13) for going to the emergency room. The highest quartile for the IFABI-R score had a sensitivity of 34.5% and a specificity of 82.2% to predict poorly controlled asthma. Parents' poorer quality of life is related to poor, medium-term asthma control in children. Assessing the parents' quality of life could aid disease management decisions. Pediatr Pulmonol. 2016;51:670-677. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

21 CFR 111.105 - What must quality control personnel do?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What must quality control personnel do? 111.105..., LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for Quality Control § 111.105 What must quality control personnel do? Quality control personnel must...

APPLICATION OF DATA QUALITY OBJECTIVES AND MEASUREMENT QUALITY OBJECTIVES TO RESEARCH PROJECTS

EPA Science Inventory

The paper assists systematic planning for research projects. It presents planning concepts in terms that have some utility for researchers. For example, measurement quality objectives are more familiar to researchers than data quality objectives because these quality criteria are...

Progressing quality control in environmental impact assessment beyond legislative compliance: An evaluation of the IEMA EIA Quality Mark certification scheme

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bond, Alan, E-mail: alan.bond@uea.ac.uk; Research Unit for Environmental Sciences and Management, North-West University; Fischer, Thomas B, E-mail: fischer@liverpool.ac.uk

The effectiveness of Environmental Impact Assessment (EIA) systems is contingent on a number of control mechanisms: procedural; judicial; evaluative; public and government agency; professional; and development aid agency. If we assume that procedural and judicial controls are guaranteed in developed EIA systems, then progressing effectiveness towards an acceptable level depends on improving the performance of other control mechanisms over time. These other control mechanisms are either absent, or are typically centrally controlled, requiring public finances; this we argue is an unpopular model in times of greater Government austerity. Here we evaluate a market-based mechanism for improving the performance of evaluativemore » and professional control mechanisms, the UK Institute of Environmental Management and Assessments' EIA Quality Mark. We do this by defining dimensions of effectiveness for the purposes of our evaluation, and by identifying international examples of the approaches taken to delivering the other control measures to validate the approach taken in the EIA Quality Mark. We then evaluate the EIA Quality Mark, when used in combination with legal procedures and an active judiciary, against the effectiveness dimensions and use time-series analysis of registrant data to examine its ability to progress practice. We conclude that the EIA Quality Mark has merit as a model for a market-based mechanism, and may prove a more financially palatable approach for delivering effective EIA in mature systems in countries that lack centralised agency oversight. It may, therefore, be of particular interest to some Member States of the European Union for ensuring forthcoming certification requirements stemming from recent amendments to the EIA Directive. - Highlights: • Quality control mechanisms in EIA are identified. • Effectiveness of EIA is conceptualised for evaluation purposes. • The UK IEMA EIA Quality Mark is introduced as a market-based mechanism. �

Quality measurement for rhinosinusitis: a review from the Quality Improvement Committee of the American Rhinologic Society.

PubMed

Rudmik, Luke; Mattos, Jose; Schneider, John; Manes, Peter R; Stokken, Janalee K; Lee, Jivianne; Higgins, Thomas S; Schlosser, Rodney J; Reh, Douglas D; Setzen, Michael; Soler, Zachary M

2017-09-01

Measuring quality outcomes is an important prerequisite to improve quality of care. Rhinosinusitis represents a high value target to improve quality of care because it has a high prevalence of disease, large economic burden, and large practice variation. In this study we review the current state of quality measurement for management of both acute (ARS) and chronic rhinosinusitis (CRS). The major national quality metric repositories and clearinghouses were queried. Additional searches included the American Academy of Otolaryngology-Head and Neck Surgery database, PubMed, and Google to attempt to capture any additional quality metrics. Seven quality metrics for ARS and 4 quality metrics for CRS were identified. ARS metrics focused on appropriateness of diagnosis (n = 1), antibiotic prescribing (n = 4), and radiologic imaging (n = 2). CRS quality metrics focused on appropriateness of diagnosis (n = 1), radiologic imaging (n = 1), and measurement of patient quality of life (n = 2). The Physician Quality Reporting System (PQRS) currently tracks 3 ARS quality metrics and 1 CRS quality metric. There are no outcome-based rhinosinusitis quality metrics and no metrics that assess domains of safety, patient-centeredness, and timeliness of care. The current status of quality measurement for rhinosinusitis has focused primarily on the quality domain of efficiency and process measures for ARS. More work is needed to develop, validate, and track outcome-based quality metrics along with CRS-specific metrics. Although there has been excellent work done to improve quality measurement for rhinosinusitis, there remain major gaps and challenges that need to be considered during the development of future metrics. © 2017 ARS-AAOA, LLC.

Measurement properties of asthma-specific quality-of-life measures: protocol for a systematic review.

PubMed

Apfelbacher, Christian; Paudyal, Priya; Bülbül, Alpaslan; Smith, Helen

2014-07-24

Asthma is a frequent chronic inflammatory disease of the airways, and the assessment of health-related quality of life (HrQoL) is important in both research and routine care. Various asthma-specific measures of HrQoL exist but there is uncertainty which measures are best suited for use in research and routine care. Therefore, the aim of the proposed research is a comprehensive systematic assessment of the measurement properties of the existing measures that were developed to measure asthma-specific quality of life. This study is a systematic review of the measurement properties of asthma-specific measures of health-related quality of life. PubMed and Embase will be searched using a selection of relevant search terms. Eligible studies will be primary empirical studies evaluating, describing or comparing measurement properties of asthma-specific HRQL tools. Eligibility assessment and data abstraction will be performed independently by two reviewers. Evidence tables will be generated for study characteristics, instrument characteristics, measurement properties and interpretability. The quality of the measurement properties will be assessed using predefined criteria. Methodological quality of studies will be assessed using the COnsensus-based Standards for the selection of health Measurement INstruments (COSMIN) checklist. A best evidence synthesis will be undertaken if more than one study have investigated a particular measurement property. The proposed systematic review will produce a comprehensive assessment of measurement properties of existing measures of asthma-specific health-related quality of life. We also aim to derive recommendations in order to help researchers and practitioners alike in the choice of instrument. PROSPERO registration number: CRD42014010491.

Commentary: measuring quality of care in osteoporosis.

PubMed

Silverman, Stuart L; Curtis, Jeffrey

2013-12-01

We know improving the quality of care in osteoporosis is an important goal. We have made some strides toward measuring quality of osteoporosis care, focusing on process measures regarding care that is provided. Unfortunately, improving care as measured by these process measures does not always yield improved outcomes. We need to hold health care providers and health care systems responsible not only for health care production but for production of health and well-being. However, there is a multiplicity of factors that will need to be considered to make this next step.

Impact on quality activities of measurement systems meeting an L:1 rule

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamada, M. S.; Burkhardt, J. H.

2016-04-01

This study considers the impact of a measurement system that meets an L:1 rule on various quality activities. These activities include inspection, acceptance sampling, and control charting. A measurement system that meets a 10:1 rule performs much better than one that meets a 4:1 rule. R code is provided so that the practitioner is able to evaluate these activities to his or her particular situation.

18 CFR 12.40 - Quality control programs.

Code of Federal Regulations, 2014 CFR

2014-04-01

... PROJECT WORKS Other Responsibilities of Applicant or Licensee § 12.40 Quality control programs. (a) General rule. During any construction, repair, or modification of project works, including any corrective... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Quality control...

18 CFR 12.40 - Quality control programs.

Code of Federal Regulations, 2013 CFR

2013-04-01

... PROJECT WORKS Other Responsibilities of Applicant or Licensee § 12.40 Quality control programs. (a) General rule. During any construction, repair, or modification of project works, including any corrective... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Quality control...

18 CFR 12.40 - Quality control programs.

Code of Federal Regulations, 2012 CFR

2012-04-01

... PROJECT WORKS Other Responsibilities of Applicant or Licensee § 12.40 Quality control programs. (a) General rule. During any construction, repair, or modification of project works, including any corrective... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Quality control...

46 CFR 164.019-13 - Production quality control requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production, manufacturing...

46 CFR 164.019-13 - Production quality control requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 6 2012-10-01 2012-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production, manufacturing...

46 CFR 164.019-13 - Production quality control requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production, manufacturing...

46 CFR 164.019-13 - Production quality control requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production, manufacturing...

46 CFR 164.019-13 - Production quality control requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production, manufacturing...

PACS quality control and automatic problem notifier

NASA Astrophysics Data System (ADS)

Honeyman-Buck, Janice C.; Jones, Douglas; Frost, Meryll M.; Staab, Edward V.

1997-05-01

One side effect of installing a clinical PACS Is that users become dependent upon the technology and in some cases it can be very difficult to revert back to a film based system if components fail. The nature of system failures range from slow deterioration of function as seen in the loss of monitor luminance through sudden catastrophic loss of the entire PACS networks. This paper describes the quality control procedures in place at the University of Florida and the automatic notification system that alerts PACS personnel when a failure has happened or is anticipated. The goal is to recover from a failure with a minimum of downtime and no data loss. Routine quality control is practiced on all aspects of PACS, from acquisition, through network routing, through display, and including archiving. Whenever possible, the system components perform self and between platform checks for active processes, file system status, errors in log files, and system uptime. When an error is detected or a exception occurs, an automatic page is sent to a pager with a diagnostic code. Documentation on each code, trouble shooting procedures, and repairs are kept on an intranet server accessible only to people involved in maintaining the PACS. In addition to the automatic paging system for error conditions, acquisition is assured by an automatic fax report sent on a daily basis to all technologists acquiring PACS images to be used as a cross check that all studies are archived prior to being removed from the acquisition systems. Daily quality control is preformed to assure that studies can be moved from each acquisition and contrast adjustment. The results of selected quality control reports will be presented. The intranet documentation server will be described with the automatic pager system. Monitor quality control reports will be described and the cost of quality control will be quantified. As PACS is accepted as a clinical tool, the same standards of quality control must be established

Quality improvement in neurology: dementia management quality measures.

PubMed

Odenheimer, Germaine; Borson, Soo; Sanders, Amy E; Swain-Eng, Rebecca J; Kyomen, Helen H; Tierney, Samantha; Gitlin, Laura; Forciea, Mary Ann; Absher, John; Shega, Joseph; Johnson, Jerry

2014-03-01

Professional and advocacy organizations have long urged that dementia should be recognized and properly diagnosed. With the passage of the National Alzheimer's Project Act in 2011, an Advisory Council for Alzheimer's Research, Care, and Services was convened to advise the Department of Health and Human Services. In May 2012, the Council produced the first National Plan to address Alzheimer's disease, and prominent in its recommendations is a call for quality measures suitable for evaluating and tracking dementia care in clinical settings. Although other efforts have been made to set dementia care quality standards, such as those pioneered by RAND in its series Assessing Care of Vulnerable Elders (ACOVE), practitioners, healthcare systems, and insurers have not widely embraced implementation. This executive summary (full manuscript available at www.neurology.org) reports on a new measurement set for dementia management developed by an interdisciplinary Dementia Measures Work Group (DWG) representing the major national organizations and advocacy organizations concerned with the care of individuals with dementia. The American Academy of Neurology (AAN), the American Geriatrics Society, the American Medical Directors Association, the American Psychiatric Association, and the American Medical Association-convened Physician Consortium for Performance Improvement led this effort. The ACOVE measures and the measurement set described here apply to individuals whose dementia has already been identified and properly diagnosed. Although similar in concept to ACOVE, the DWG measurement set differs in several important ways; it includes all stages of dementia in a single measure set, calls for the use of functional staging in planning care, prompts the use of validated instruments in patient and caregiver assessment and intervention, highlights the relevance of using palliative care concepts to guide care before the advanced stages of illness, and provides evidence-based support

Quality by control: Towards model predictive control of mammalian cell culture bioprocesses.

PubMed

Sommeregger, Wolfgang; Sissolak, Bernhard; Kandra, Kulwant; von Stosch, Moritz; Mayer, Martin; Striedner, Gerald

2017-07-01

The industrial production of complex biopharmaceuticals using recombinant mammalian cell lines is still mainly built on a quality by testing approach, which is represented by fixed process conditions and extensive testing of the end-product. In 2004 the FDA launched the process analytical technology initiative, aiming to guide the industry towards advanced process monitoring and better understanding of how critical process parameters affect the critical quality attributes. Implementation of process analytical technology into the bio-production process enables moving from the quality by testing to a more flexible quality by design approach. The application of advanced sensor systems in combination with mathematical modelling techniques offers enhanced process understanding, allows on-line prediction of critical quality attributes and subsequently real-time product quality control. In this review opportunities and unsolved issues on the road to a successful quality by design and dynamic control implementation are discussed. A major focus is directed on the preconditions for the application of model predictive control for mammalian cell culture bioprocesses. Design of experiments providing information about the process dynamics upon parameter change, dynamic process models, on-line process state predictions and powerful software environments seem to be a prerequisite for quality by control realization. © 2017 The Authors. Biotechnology Journal published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analytical approaches to quality assurance and quality control in rangeland monitoring data

USDA-ARS?s Scientific Manuscript database

Producing quality data to support land management decisions is the goal of every rangeland monitoring program. However, the results of quality assurance (QA) and quality control (QC) efforts to improve data quality are rarely reported. The purpose of QA and QC is to prevent and describe non-sampling...

Professional Development for Water Quality Control Personnel.

ERIC Educational Resources Information Center

Shepard, Clinton Lewis

This study investigated the availability of professional development opportunities for water quality control personnel in the midwest. The major objective of the study was to establish a listing of educational opportunities for the professional development of water quality control personnel and to compare these with the opportunities technicians…

DUQuE quality management measures: associations between quality management at hospital and pathway levels.

PubMed

Wagner, Cordula; Groene, Oliver; Thompson, Caroline A; Dersarkissian, Maral; Klazinga, Niek S; Arah, Onyebuchi A; Suñol, Rosa

2014-04-01

The assessment of integral quality management (QM) in a hospital requires measurement and monitoring from different perspectives and at various levels of care delivery. Within the DUQuE project (Deepening our Understanding of Quality improvement in Europe), seven measures for QM were developed. This study investigates the relationships between the various quality measures. It is a multi-level, cross-sectional, mixed-method study. As part of the DUQuE project, we invited a random sample of 74 hospitals in 7 countries. The quality managers of these hospitals were the main respondents. Furthermore, data of site visits of external surveyors assessing the participating hospitals were used. Three measures of QM at hospitals level focusing on integral systems (QMSI), compliance with the Plan-Do-Study-Act quality improvement cycle (QMCI) and implementation of clinical quality (CQII). Four measures of QM activities at care pathway level focusing on Specialized expertise and responsibility (SER), Evidence-based organization of pathways (EBOP), Patient safety strategies (PSS) and Clinical review (CR). Positive significant associations were found between the three hospitals level QM measures. Results of the relationships between levels were mixed and showed most associations between QMCI and department-level QM measures for all four types of departments. QMSI was associated with PSS in all types of departments. By using the seven measures of QM, it is possible to get a more comprehensive picture of the maturity of QM in hospitals, with regard to the different levels and across various types of hospital departments.

Measuring the Mathematical Quality of Instruction

ERIC Educational Resources Information Center

Journal of Mathematics Teacher Education, 2011

2011-01-01

In this article, we describe a framework and instrument for measuring the mathematical quality of mathematics instruction. In describing this framework, we argue for the separation of the "mathematical quality of instruction" (MQI), such as the absence of mathematical errors and the presence of sound mathematical reasoning, from pedagogical…

Ride quality sensitivity to SAS control law and to handling quality variations

NASA Technical Reports Server (NTRS)

Roberts, P. A.; Schmidt, D. K.; Swaim, R. L.

1976-01-01

The RQ trends which large flexible aircraft exhibit under various parameterizations of control laws and handling qualities are discussed. A summary of the assumptions and solution technique, a control law parameterization review, a discussion of ride sensitivity to handling qualities, and the RQ effects generated by implementing relaxed static stability configurations are included.

14 CFR 21.147 - Changes in quality control system.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Changes in quality control system. 21.147 Section 21.147 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... quality control system. After the issue of a production certificate, each change to the quality control...

14 CFR 21.147 - Changes in quality control system.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Changes in quality control system. 21.147 Section 21.147 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... quality control system. After the issue of a production certificate, each change to the quality control...

21 CFR 111.117 - What quality control operations are required for equipment, instruments, and controls?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for equipment, instruments, and controls? 111.117 Section 111.117 Food and Drugs FOOD AND DRUG ADMINISTRATION... and Process Control System: Requirements for Quality Control § 111.117 What quality control operations...

Patient-Reported Outcomes for Quality of Life Assessment in Atrial Fibrillation: A Systematic Review of Measurement Properties.

PubMed

Kotecha, Dipak; Ahmed, Amar; Calvert, Melanie; Lencioni, Mauro; Terwee, Caroline B; Lane, Deirdre A

2016-01-01

Atrial fibrillation is a large and growing burden across all types of healthcare. Both incidence and prevalence are expected to double in the next 20 years, with huge impact on hospital admissions, costs and patient quality of life. Patient wellbeing determines the management strategy for atrial fibrillation, including the use of rhythm control therapy and the clinical success of heart rate control. Hence, evaluation of quality of life is an emerging and important part of the assessment of patients with atrial fibrillation. Although a number of questionnaires to assess quality of life in atrial fibrillation are available, a comprehensive overview of their measurement properties is lacking. We performed a systematic review of the measurement properties of atrial fibrillation-specific health-related quality of life questionnaires. Methodological quality was assessed using the Consensus based Standards for selection of health Measurement Instruments (COSMIN) checklist, with measurement properties rated for quality against optimal criteria and levels of evidence. We screened 2,216 articles, of which eight articles describing five questionnaires were eligible for inclusion: Atrial Fibrillation 6 (AF6), Atrial Fibrillation Effect on QualiTy-of-Life (AFEQT), Atrial Fibrillation Quality of Life Questionnaire (AFQLQ), Atrial Fibrillation Quality of Life (AFQoL), and Quality of Life in Atrial Fibrillation (QLAF). Good reliability (internal consistency and test-retest reliability) was demonstrated for AF6, AFEQT, AFQLQ and AFQoL. Content, construct and criterion validity were positively rated only in AFEQT. Responsiveness was positively rated only in AFEQT, but with limited evidence. Overall, AFEQT showed strong positive evidence for 2 of 9 measurement properties, compared to one for AFQoL and none for the remaining questionnaires. Given the low ratings for many measurement properties, no single questionnaire can be recommended, although AFEQT performed strongest. Further

Towards an integrated quality control procedure for eddy-covariance data

NASA Astrophysics Data System (ADS)

Vitale, Domenico; Papale, Dario

2017-04-01

The eddy-covariance technique is nowadays the most reliable and direct way, allowing to calculate the main fluxes of Sensible and Latent Heat and of Net Ecosystem Exchange, this last being the result of the difference between the CO2 assimilated by photosynthetic activities and those released to the atmosphere through the ecosystem respiration processes. Despite the improvements in accuracy of measurement instruments and software development, the eddy-covariance technique is not suitable under non-ideal conditions respect to the instruments characteristics and the physical assumption behind the technique mainly related to the well-developed and stationary turbulence conditions. Under these conditions the calculated fluxes are not reliable and need to be flagged and discarded. In order to discover these unavoidable "bad" fluxes and build dataset with the highest quality, several tests applied both on high-frequency (10-20 Hz) raw data and on half-hourly times series have been developed in the past years. Nevertheless, there is an increasing need to develop a standardized quality control procedure suitable not only for the analysis of long-term data, but also for the near-real time data processing. In this paper, we review established quality assessment procedures and present an innovative quality control strategy with the purpose of integrating the existing consolidated procedures with robust and advanced statistical tests more suitable for the analysis of time series data. The performance of the proposed quality control strategy is evaluated both on simulated and EC data distributed by the ICOS research infrastructure. It is concluded that the proposed strategy is able to flag and exclude unrealistic fluxes while being reproducible and retaining the largest possible amount of high quality data.

Colorado Air Quality Control Regulations and Ambient Air Quality Standards.

ERIC Educational Resources Information Center

Colorado State Dept. of Health, Denver. Div. of Air Pollution Control.

Regulations and standards relative to air quality control in Colorado are defined in this publication. Presented first are definitions of terms, a statement of intent, and general provisions applicable to all emission control regulations adopted by the Colorado Air Pollution Control Commission. Following this, three regulations are enumerated: (1)…

46 CFR 164.120-11 - Production quality control requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Production quality control requirements. 164.120-11... Rescue Boats § 164.120-11 Production quality control requirements. The resin manufacturer must institute a quality control procedure to ensure that all Coast Guard-accepted resin is produced to the same...

46 CFR 164.120-11 - Production quality control requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 6 2012-10-01 2012-10-01 false Production quality control requirements. 164.120-11... Rescue Boats § 164.120-11 Production quality control requirements. The resin manufacturer must institute a quality control procedure to ensure that all Coast Guard-accepted resin is produced to the same...

46 CFR 164.120-11 - Production quality control requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Production quality control requirements. 164.120-11... Rescue Boats § 164.120-11 Production quality control requirements. The resin manufacturer must institute a quality control procedure to ensure that all Coast Guard-accepted resin is produced to the same...

Quality Control Technician Curriculum. An Elusive Butterfly.

ERIC Educational Resources Information Center

Holler, Michael

Defining and developing a quality control technician curriculum for an associate degree program is a difficult and puzzling job. There are as many definitions of quality control and curriculum ideas as there are educators asked. However, one could start by dividing the field into its major areas--heavy manufacturing, maintenance, research, and…

Random Forest Application for NEXRAD Radar Data Quality Control

NASA Astrophysics Data System (ADS)

Keem, M.; Seo, B. C.; Krajewski, W. F.

2017-12-01

Identification and elimination of non-meteorological radar echoes (e.g., returns from ground, wind turbines, and biological targets) are the basic data quality control steps before radar data use in quantitative applications (e.g., precipitation estimation). Although WSR-88Ds' recent upgrade to dual-polarization has enhanced this quality control and echo classification, there are still challenges to detect some non-meteorological echoes that show precipitation-like characteristics (e.g., wind turbine or anomalous propagation clutter embedded in rain). With this in mind, a new quality control method using Random Forest is proposed in this study. This classification algorithm is known to produce reliable results with less uncertainty. The method introduces randomness into sampling and feature selections and integrates consequent multiple decision trees. The multidimensional structure of the trees can characterize the statistical interactions of involved multiple features in complex situations. The authors explore the performance of Random Forest method for NEXRAD radar data quality control. Training datasets are selected using several clear cases of precipitation and non-precipitation (but with some non-meteorological echoes). The model is structured using available candidate features (from the NEXRAD data) such as horizontal reflectivity, differential reflectivity, differential phase shift, copolar correlation coefficient, and their horizontal textures (e.g., local standard deviation). The influence of each feature on classification results are quantified by variable importance measures that are automatically estimated by the Random Forest algorithm. Therefore, the number and types of features in the final forest can be examined based on the classification accuracy. The authors demonstrate the capability of the proposed approach using several cases ranging from distinct to complex rain/no-rain events and compare the performance with the existing algorithms (e

Quality Measurement in Early Childhood Settings

ERIC Educational Resources Information Center

Zaslow, Martha, Ed.; Martinez-Beck, Ivelisse, Ed.; Tout, Kathryn, Ed.; Halle, Tamara, Ed.

2011-01-01

What constitutes quality in early childhood settings, and how can it best be measured with today's widely used tools and promising new approaches? Find authoritative answers in this book, a must-have for high-level administrators and policymakers as more and more states adopt early childhood Quality Rating and Improvement Systems. The most…

7 CFR 58.523 - Laboratory and quality control tests.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 3 2014-01-01 2014-01-01 false Laboratory and quality control tests. 58.523 Section... Service 1 Operations and Operating Procedures § 58.523 Laboratory and quality control tests. (a) Quality control tests shall be made on samples as often as necessary to determine the shelf-life and stability of...

7 CFR 58.523 - Laboratory and quality control tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Laboratory and quality control tests. 58.523 Section... Service 1 Operations and Operating Procedures § 58.523 Laboratory and quality control tests. (a) Quality control tests shall be made on samples as often as necessary to determine the shelf-life and stability of...

7 CFR 58.523 - Laboratory and quality control tests.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 3 2013-01-01 2013-01-01 false Laboratory and quality control tests. 58.523 Section... Service 1 Operations and Operating Procedures § 58.523 Laboratory and quality control tests. (a) Quality control tests shall be made on samples as often as necessary to determine the shelf-life and stability of...

7 CFR 58.523 - Laboratory and quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Laboratory and quality control tests. 58.523 Section... Service 1 Operations and Operating Procedures § 58.523 Laboratory and quality control tests. (a) Quality control tests shall be made on samples as often as necessary to determine the shelf-life and stability of...

7 CFR 58.523 - Laboratory and quality control tests.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 3 2012-01-01 2012-01-01 false Laboratory and quality control tests. 58.523 Section... Service 1 Operations and Operating Procedures § 58.523 Laboratory and quality control tests. (a) Quality control tests shall be made on samples as often as necessary to determine the shelf-life and stability of...

21 CFR 640.56 - Quality control test for potency.

Code of Federal Regulations, 2010 CFR

2010-04-01

... quality control test for potency may be performed by a clinical laboratory which meets the standards of... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Quality control test for potency. 640.56 Section...) BIOLOGICS ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Cryoprecipitate § 640.56 Quality control...

[Technological innovations in radiation oncology require specific quality controls].

PubMed

Lenaerts, E; Mathot, M

2014-01-01

During the last decade, the field of radiotherapy has benefited from major technological innovations and continuously improving treatment efficacy, comfort and safety of patients. This mainly concerns the imaging techniques that allow 4D CT scan recording the respiratory phases, on-board imaging on linear accelerators that ensure perfect positioning of the patient for treatment and irradiation techniques that reduce very significantly the duration of treatment sessions without compromising quality of the treatment plan, including IMRT (Intensity Modulated Radiation Therapy) and VMAT (Volumetric Modulated Arc therapy). In this context of rapid technological change, it is the responsibility of medical physicists to regularly and precisely monitor the perfect functioning of new techniques to ensure patient safety. This requires the use of specific quality control equipment best suited to these new techniques. We will briefly describe the measurement system Delta4 used to control individualized treatment plan for each patient treated with VMAT technology.

Web quality control for lectures: Supercourse and Amazon.com.

PubMed

Linkov, Faina; LaPorte, Ronald; Lovalekar, Mita; Dodani, Sunita

2005-12-01

Peer review has been at the corner stone of quality control of the biomedical journals in the past 300 years. With the emergency of the Internet, new models of quality control and peer review are emerging. However, such models are poorly investigated. We would argue that the popular system of quality control used in Amazon.com offers a way to ensure continuous quality improvement in the area of research communications on the Internet. Such system is providing an interesting alternative to the traditional peer review approaches used in the biomedical journals and challenges the traditional paradigms of scientific publishing. This idea is being explored in the context of Supercourse, a library of 2,350 prevention lectures, shared for free by faculty members from over 150 countries. Supercourse is successfully utilizing quality control approaches that are similar to Amazon.com model. Clearly, the existing approaches and emerging alternatives for quality control in scientific communications needs to be assessed scientifically. Rapid explosion of internet technologies could be leveraged to produce better, more cost effective systems for quality control in the biomedical publications and across all sciences.

40 CFR 81.107 - Greenwood Intrastate Air Quality Control Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Quality Control Regions § 81.107 Greenwood Intrastate Air Quality Control Region. The Greenwood Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Greenwood Intrastate Air Quality...

40 CFR 81.108 - Columbia Intrastate Air Quality Control Region.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Quality Control Regions § 81.108 Columbia Intrastate Air Quality Control Region. The Columbia Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Columbia Intrastate Air Quality...

40 CFR 81.108 - Columbia Intrastate Air Quality Control Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Quality Control Regions § 81.108 Columbia Intrastate Air Quality Control Region. The Columbia Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Columbia Intrastate Air Quality...

40 CFR 81.111 - Georgetown Intrastate Air Quality Control Region.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Quality Control Regions § 81.111 Georgetown Intrastate Air Quality Control Region. The Georgetown Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Georgetown Intrastate Air Quality...

40 CFR 81.109 - Florence Intrastate Air Quality Control Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Quality Control Regions § 81.109 Florence Intrastate Air Quality Control Region. The Florence Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Florence Intrastate Air Quality...

40 CFR 81.111 - Georgetown Intrastate Air Quality Control Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Quality Control Regions § 81.111 Georgetown Intrastate Air Quality Control Region. The Georgetown Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Georgetown Intrastate Air Quality...

40 CFR 81.109 - Florence Intrastate Air Quality Control Region.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Quality Control Regions § 81.109 Florence Intrastate Air Quality Control Region. The Florence Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Florence Intrastate Air Quality...

40 CFR 81.107 - Greenwood Intrastate Air Quality Control Region.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Quality Control Regions § 81.107 Greenwood Intrastate Air Quality Control Region. The Greenwood Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Greenwood Intrastate Air Quality...

The Joint Commission Children’s Asthma Care Quality Measures and Asthma Readmissions

PubMed Central

Fassl, Bernhard A.; Nkoy, Flory L.; Stone, Bryan L.; Srivastava, Rajendu; Simon, Tamara D.; Uchida, Derek A.; Koopmeiners, Karmella; Greene, Tom; Cook, Lawrence J.

2012-01-01

BACKGROUND AND OBJECTIVES: The Joint Commission introduced 3 Children’s Asthma Care (CAC 1–3) measures to improve the quality of pediatric inpatient asthma care. Validity of the commission’s measures has not yet been demonstrated. The objectives of this quality improvement study were to examine changes in provider compliance with CAC 1–3 and associated asthma hospitalization outcomes after full implementation of an asthma care process model (CPM). METHODS: The study included children aged 2 to 17 years who were admitted to a tertiary care children’s hospital for acute asthma between January 1, 2005, and December 31, 2010. The study was divided into 3 periods: preimplementation (January 1, 2005–December 31, 2007), implementation (January 1, 2008–March 31, 2009), and postimplementation (April 1, 2009–December 31, 2010) periods. Changes in provider compliance with CAC 1–3 and associated changes in hospitalization outcomes (length of stay, costs, PICU transfer, deaths, and asthma readmissions within 6 months) were measured. Logistic regression was used to control for age, gender, race, insurance type, and time. RESULTS: A total of 1865 children were included. Compliance with quality measures before and after the CPM implementation was as follows: 99% versus 100%, CAC-1; 100% versus 100%, CAC-2; and 0% versus 87%, CAC-3 (P < .01). Increased compliance with CAC-3 was associated with a sustained decrease in readmissions from an average of 17% to 12% (P = .01) postimplementation. No change in other outcomes was observed. CONCLUSIONS: Implementation of the asthma CPM was associated with improved compliance with CAC-3 and with a delayed, yet significant and sustained decrease in hospital asthma readmission rates, validating CAC-3 as a quality measure. Due to high baseline compliance, CAC-1 and CAC-2 are of questionable value as quality measures. PMID:22908110

Improving NGDC Track-line Data Quality Control

NASA Astrophysics Data System (ADS)

Chandler, M. T.; Wessel, P.

2004-12-01

Ship-board gravity, magnetic and bathymetry data archived at the National Geophysical Data Center (NGDC) represent decades of seagoing research, containing over 4,500 cruises. Cruise data remain relevent despite the prominence of satellite altimetry-derived global grids because many geologic processes remain resolvable by oceanographic research alone. Due to the tremendous investment put forth by scientists and taxpayers to compile this vast archive and the significant errors found within it, additional quality assessment and corrections are warranted. These can best be accomplished by adding to existing quality control measures at NGDC. We are currently developing open source software to provide additional quality control. Along with NGDC's current sanity checking, new data at NGDC will also be subjected to an along-track ``sniffer'' which will detect and flag suspicious data for later graphical inspection using a visual editor. If new data pass these tests, they will undergo further scrutinization using a crossover error (COE) calculator which will compare new data values to existing values at points of intersection within the archive. Data passing these tests will be deemed ``quality data`` and suitable for permanent addition to the archive, while data that fail will be returned to the source institution for correction. Crossover errors will be stored and an online COE database will be available. The COE database will allow users to apply corrections to the NGDC track-line database to produce corrected data files. At no time will the archived data itself be modified. An attempt will also be made to reduce navigational errors for pre-GPS navigated cruises. Upon completion these programs will be used to explore and model systematic errors within the archive, generate correction tables for all cruises, and to quantify the error budget in marine geophysical observations. Software will be released and these procedures will be implemented in cooperation with NGDC

Cancer control in developing countries: using health data and health services research to measure and improve access, quality and efficiency.

PubMed

Hanna, Timothy P; Kangolle, Alfred C T

2010-10-13

Cancer is a rapidly increasing problem in developing countries. Access, quality and efficiency of cancer services in developing countries must be understood to advance effective cancer control programs. Health services research can provide insights into these areas. This article provides an overview of oncology health services in developing countries. We use selected examples from peer-reviewed literature in health services research and relevant publicly available documents. In spite of significant limitations in the available data, it is clear there are substantial barriers to access to cancer control in developing countries. This includes prevention, early detection, diagnosis/treatment and palliation. There are also substantial limitations in the quality of cancer control and a great need to improve economic efficiency. We describe how the application of health data may assist in optimizing (1) Structure: strengthening planning, collaboration, transparency, research development, education and capacity building. (2) PROCESS: enabling follow-up, knowledge translation, patient safety and quality assurance. (3) OUTCOME: facilitating evaluation, monitoring and improvement of national cancer control efforts. There is currently limited data and capacity to use this data in developing countries for these purposes. There is an urgent need to improve health services for cancer control in developing countries. Current resources and much-needed investments must be optimally managed. To achieve this, we would recommend investment in four key priorities: (1) Capacity building in oncology health services research, policy and planning relevant to developing countries. (2) Development of high-quality health data sources. (3) More oncology-related economic evaluations in developing countries. (4) Exploration of high-quality models of cancer control in developing countries. Meeting these needs will require national, regional and international collaboration as well as political

Cancer control in developing countries: using health data and health services research to measure and improve access, quality and efficiency

PubMed Central

2010-01-01

Background Cancer is a rapidly increasing problem in developing countries. Access, quality and efficiency of cancer services in developing countries must be understood to advance effective cancer control programs. Health services research can provide insights into these areas. Discussion This article provides an overview of oncology health services in developing countries. We use selected examples from peer-reviewed literature in health services research and relevant publicly available documents. In spite of significant limitations in the available data, it is clear there are substantial barriers to access to cancer control in developing countries. This includes prevention, early detection, diagnosis/treatment and palliation. There are also substantial limitations in the quality of cancer control and a great need to improve economic efficiency. We describe how the application of health data may assist in optimizing (1) Structure: strengthening planning, collaboration, transparency, research development, education and capacity building. (2) Process: enabling follow-up, knowledge translation, patient safety and quality assurance. (3) Outcome: facilitating evaluation, monitoring and improvement of national cancer control efforts. There is currently limited data and capacity to use this data in developing countries for these purposes. Summary There is an urgent need to improve health services for cancer control in developing countries. Current resources and much-needed investments must be optimally managed. To achieve this, we would recommend investment in four key priorities: (1) Capacity building in oncology health services research, policy and planning relevant to developing countries. (2) Development of high-quality health data sources. (3) More oncology-related economic evaluations in developing countries. (4) Exploration of high-quality models of cancer control in developing countries. Meeting these needs will require national, regional and international

Contractor Performed Quality Control on KyTC Projects.

DOT National Transportation Integrated Search

2002-08-01

This report addresses issues related to transferring the responsibility for quality control from the Kentucky Transportation Cabinet (KyTC) to construction contractors. : Several key topics related to Contractor Performed Quality Control (CPQC) are p...

[Pharmaceutical product quality control and good manufacturing practices].

PubMed

Hiyama, Yukio

2010-01-01

This report describes the roles of Good Manufacturing Practices (GMP) in pharmaceutical product quality control. There are three keys to pharmaceutical product quality control. They are specifications, thorough product characterization during development, and adherence to GMP as the ICH Q6A guideline on specifications provides the most important principles in its background section. Impacts of the revised Pharmaceutical Affairs Law (rPAL) which became effective in 2005 on product quality control are discussed. Progress of ICH discussion for Pharmaceutical Development (Q8), Quality Risk Management (Q9) and Pharmaceutical Quality System (Q10) are reviewed. In order to reconstruct GMP guidelines and GMP inspection system in the regulatory agencies under the new paradigm by rPAL and the ICH, a series of Health Science studies were conducted. For GMP guidelines, product GMP guideline, technology transfer guideline, laboratory control guideline and change control system guideline were written. For the GMP inspection system, inspection check list, inspection memo and inspection scenario were proposed also by the Health Science study groups. Because pharmaceutical products and their raw materials are manufactured and distributed internationally, collaborations with other national authorities are highly desired. In order to enhance the international collaborations, consistent establishment of GMP inspection quality system throughout Japan will be essential.

21 CFR 862.1660 - Quality control material (assayed and unassayed).

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Quality control material (assayed and unassayed... Test Systems § 862.1660 Quality control material (assayed and unassayed). (a) Identification. A quality... that may arise from reagent or analytical instrument variation. A quality control material (assayed and...

Routine internal- and external-quality control data in clinical laboratories for estimating measurement and diagnostic uncertainty using GUM principles.

PubMed

Magnusson, Bertil; Ossowicki, Haakan; Rienitz, Olaf; Theodorsson, Elvar

2012-05-01

Healthcare laboratories are increasingly joining into larger laboratory organizations encompassing several physical laboratories. This caters for important new opportunities for re-defining the concept of a 'laboratory' to encompass all laboratories and measurement methods measuring the same measurand for a population of patients. In order to make measurement results, comparable bias should be minimized or eliminated and measurement uncertainty properly evaluated for all methods used for a particular patient population. The measurement as well as diagnostic uncertainty can be evaluated from internal and external quality control results using GUM principles. In this paper the uncertainty evaluations are described in detail using only two main components, within-laboratory reproducibility and uncertainty of the bias component according to a Nordtest guideline. The evaluation is exemplified for the determination of creatinine in serum for a conglomerate of laboratories both expressed in absolute units (μmol/L) and relative (%). An expanded measurement uncertainty of 12 μmol/L associated with concentrations of creatinine below 120 μmol/L and of 10% associated with concentrations above 120 μmol/L was estimated. The diagnostic uncertainty encompasses both measurement uncertainty and biological variation, and can be estimated for a single value and for a difference. This diagnostic uncertainty for the difference for two samples from the same patient was determined to be 14 μmol/L associated with concentrations of creatinine below 100 μmol/L and 14 % associated with concentrations above 100 μmol/L.

QUALITY ASSURANCE AND QUALITY CONTROL FOR WASTE CONTAINMENT FACILITIES. Project Summary

EPA Science Inventory

It is generally agreed that both quality assurance (QA) and quality control (QC) are essential to the proper installation and eventual performance of environmentally safe and secure waste containment systems. Even further, there are both manufacturing and construction aspects to...

A Framework for a Quality Control System for Vendor/Processor Contracts.

ERIC Educational Resources Information Center

Advanced Technology, Inc., Reston, VA.

A framework for monitoring quality control (QC) of processor contracts administered by the Department of Education's Office of Student Financial Assistance (OSFA) is presented and applied to the Pell Grant program. Guidelines for establishing QC measures and standards are included, and the uses of a sampling procedure in the QC system are…

Information quality measurement of medical encoding support based on usability.

PubMed

Puentes, John; Montagner, Julien; Lecornu, Laurent; Cauvin, Jean-Michel

2013-12-01

Medical encoding support systems for diagnoses and medical procedures are an emerging technology that begins to play a key role in billing, reimbursement, and health policies decisions. A significant problem to exploit these systems is how to measure the appropriateness of any automatically generated list of codes, in terms of fitness for use, i.e. their quality. Until now, only information retrieval performance measurements have been applied to estimate the accuracy of codes lists as quality indicator. Such measurements do not give the value of codes lists for practical medical encoding, and cannot be used to globally compare the quality of multiple codes lists. This paper defines and validates a new encoding information quality measure that addresses the problem of measuring medical codes lists quality. It is based on a usability study of how expert coders and physicians apply computer-assisted medical encoding. The proposed measure, named ADN, evaluates codes Accuracy, Dispersion and Noise, and is adapted to the variable length and content of generated codes lists, coping with limitations of previous measures. According to the ADN measure, the information quality of a codes list is fully represented by a single point, within a suitably constrained feature space. Using one scheme, our approach is reliable to measure and compare the information quality of hundreds of codes lists, showing their practical value for medical encoding. Its pertinence is demonstrated by simulation and application to real data corresponding to 502 inpatient stays in four clinic departments. Results are compared to the consensus of three expert coders who also coded this anonymized database of discharge summaries, and to five information retrieval measures. Information quality assessment applying the ADN measure showed the degree of encoding-support system variability from one clinic department to another, providing a global evaluation of quality measurement trends. Copyright © 2013

Emission controls and changes in air quality in Guangzhou during the Asian Games

NASA Astrophysics Data System (ADS)

Liu, Huan; Wang, Xuemei; Zhang, Jinpu; He, Kebin; Wu, Ye; Xu, Jiayu

2013-09-01

With the new air quality standards forthcoming in China, the Pearl River Delta region is facing new challenges to achieve its air quality goal. The success of the emission reduction measures introduced by local authorities in the run-up to the Guangzhou Asian Games demonstrated that the Pearl River Delta air quality can be improved by introducing integrated emission reduction measures. This paper combines observation data, emission reduction measures, and air quality simulations that were applied during the Asian Games (12-27 November 2010) to analyze the relationship between emissions and concentrations of pollutants in Guangzhou. The Asian Games abatement strategy totally reduced emissions of 41.1% SO2, 41.9% NOx, 26.5% PM10, 25.8% PM2.5 and 39.7% VOC. The concentrations of SO2, NO2, PM10 and PM2.5 were reduced by 66.8%, 51.3%, 21.5% and 17.1%, respectively. In Guangzhou, the main challenge to be overcome with the new air quality daily requirements is mostly for NO2, PM2.5, and hourly ozone maxima. If pollutants maintain the same concentrations before and after the Asian Games, there will be 47.4% and 31.6% non-attainment days for NO2 and PM2.5 respectively as a period average. Although PM10 concentration can meet the daily limits (150 μg m-3), it is quite difficult to meet the annual limit value (70 μg m-3). One important implication is that the long-term, step-by-step integrated measures of the past six years work better than the strict, intensive, short-term measures on SO2, NO2 and VOC control. Dust control by limiting construction sites and watering the roads can further reduce 12.8% of the PM10 concentration. However, to reduce ambient PM2.5, the abatement strategy should be more complex and extensive. On the contrary, ozone pollution was not improved during the Asian Games, indicating that alleviation strategies should be improved by scientific studies to determine the appropriate control ratio of NO2 and VOC in the Pearl River Delta region.

Quality measures and assurance for AI (Artificial Intelligence) software

NASA Technical Reports Server (NTRS)

Rushby, John

1988-01-01

This report is concerned with the application of software quality and evaluation measures to AI software and, more broadly, with the question of quality assurance for AI software. Considered are not only the metrics that attempt to measure some aspect of software quality, but also the methodologies and techniques (such as systematic testing) that attempt to improve some dimension of quality, without necessarily quantifying the extent of the improvement. The report is divided into three parts Part 1 reviews existing software quality measures, i.e., those that have been developed for, and applied to, conventional software. Part 2 considers the characteristics of AI software, the applicability and potential utility of measures and techniques identified in the first part, and reviews those few methods developed specifically for AI software. Part 3 presents an assessment and recommendations for the further exploration of this important area.

Advancing the use of community pharmacy quality measures: a qualitative study.

PubMed

Shiyanbola, Olayinka O; Mort, Jane R; Lyons, Kayley

2013-01-01

To describe consumers' ability to interpret pharmacy quality measures data presented in a report card, to examine the tools that consumers require to interpret the information available in a pharmacy quality report card, and to determine whether pharmacy quality measures influence consumers' choice of a pharmacy. Qualitative study. Three semistructured focus groups conducted in a private meeting space at a public library in Sioux Falls, SD, from April 2011 to May 2011. 29 laypeople. Participants' skills interpreting and using pharmacy quality information were examined based on mock report cards containing the Pharmacy Quality Alliance (PQA) quality measures. Consumer perceptions of pharmacy quality data. Participants reported difficulty understanding quality measures because of knowledge deficits. They wanted supportive resources on drug class of their medications to help them understand the measures. Participants had different opinions on whether their pharmacies should be compared with other pharmacies based on specific quality measures. For example, they favored the use of drug-drug interactions as a quality measure for comparing pharmacies, while medication adherence was deemed of limited use for comparison. Participants stated that pharmacy report cards would be useful information but would not prompt a change in pharmacy. However, participants perceived that this information would be useful in selecting a new pharmacy. The results suggest that consumers require simplification of PQA quality measures and supportive resources to interpret the measures. Consumers may favor certain quality measures based on their perception of the role of the pharmacist. Education is required before full use of this quality-of-care information can be realized.

The evolving landscape of quality measurement for heart failure

PubMed Central

Fitzgerald, Ashley A.; Allen, Larry A.; Masoudi, Frederick A.

2013-01-01

Heart failure (HF) is a major cause of mortality and morbidity, representing a leading cause of death and hospitalization among U.S. Medicare beneficiaries. Advances in science have generated effective interventions to reduce adverse outcomes in HF, particularly in patients with reduced left ventricular ejection fraction. Unfortunately, effective therapies for heart failure are often not utilized in an effective, safe, timely, equitable, patient-centered, and efficient manner. Further, the risk of adverse outcomes for HF remains high. The last decades have witnessed the growth of efforts to measure and improve the care and outcomes of patients with HF. This paper will review the evolution of quality measurement for HF, including a brief history of quality measurement in medicine; the measures that have been employed to characterize quality in heart failure; how the measures are obtained; how measures are employed; and present and future challenges surrounding quality measurement in heart failure. PMID:22548579

Instrumentation for air quality measurements.

NASA Technical Reports Server (NTRS)

Loewenstein, M.

1973-01-01

Comparison of the new generation of air quality monitoring instruments with some more traditional methods. The first generation of air quality measurement instruments, based on the use of oxidant coulometric cells, nitrogen oxide colorimetry, carbon monoxide infrared analyzers, and other types of detectors, is compared with new techniques now coming into wide use in the air monitoring field and involving the use of chemiluminescent reactions, optical absorption detectors, a refinement of the carbon monoxide infrared analyzer, electrochemical cells based on solid electrolytes, and laser detectors.

[Post-marketing reevaluation for potential quality risk and quality control in clinical application of traditional Chinese medicines].

PubMed

Li, Hong-jiao; He, Li-yun; Liu, Bao-yan

2015-06-01

The effective quality control in clinical practices is an effective guarantee for the authenticity and scientificity of the findings. The post-marketing reevaluation for traditional Chinese medicines (TCM) focuses on the efficacy, adverse reaction, combined medication and effective dose of drugs in the market by expanded clinical trials, and requires a larger sample size and a wider range of patients. Therefore, this increases the difficulty of quality control in clinical practices. With the experience in quality control in clinical practices for the post-marketing reevaluation for Kangbingdu oral for cold, researchers in this study reviewed the study purpose, project, scheme design and clinical practice process from an overall point of view, analyzed the study characteristics of the post-marketing reevaluation for TCMs and the quality control risks, designed the quality control contents with quality impacting factors, defined key review contents and summarized the precautions in clinical practices, with the aim to improve the efficiency of quality control of clinical practices. This study can provide reference to clinical units and quality control-related personnel in the post-marketing reevaluation for TCMs.

Competency-Based Education: A Framework for Measuring Quality Courses

ERIC Educational Resources Information Center

Krause, Jackie; Dias, Laura Portolese; Schedler, Chris

2015-01-01

The growth of competency-based education in an online environment requires the development and measurement of quality competency-based courses. While quality measures for online courses have been developed and standardized, they do not directly align with emerging best practices and principles in the design of quality competency-based online…

Quality Control of High-Dose-Rate Brachytherapy: Treatment Delivery Analysis Using Statistical Process Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Able, Charles M., E-mail: cable@wfubmc.edu; Bright, Megan; Frizzell, Bart

Purpose: Statistical process control (SPC) is a quality control method used to ensure that a process is well controlled and operates with little variation. This study determined whether SPC was a viable technique for evaluating the proper operation of a high-dose-rate (HDR) brachytherapy treatment delivery system. Methods and Materials: A surrogate prostate patient was developed using Vyse ordnance gelatin. A total of 10 metal oxide semiconductor field-effect transistors (MOSFETs) were placed from prostate base to apex. Computed tomography guidance was used to accurately position the first detector in each train at the base. The plan consisted of 12 needles withmore » 129 dwell positions delivering a prescribed peripheral dose of 200 cGy. Sixteen accurate treatment trials were delivered as planned. Subsequently, a number of treatments were delivered with errors introduced, including wrong patient, wrong source calibration, wrong connection sequence, single needle displaced inferiorly 5 mm, and entire implant displaced 2 mm and 4 mm inferiorly. Two process behavior charts (PBC), an individual and a moving range chart, were developed for each dosimeter location. Results: There were 4 false positives resulting from 160 measurements from 16 accurately delivered treatments. For the inaccurately delivered treatments, the PBC indicated that measurements made at the periphery and apex (regions of high-dose gradient) were much more sensitive to treatment delivery errors. All errors introduced were correctly identified by either the individual or the moving range PBC in the apex region. Measurements at the urethra and base were less sensitive to errors. Conclusions: SPC is a viable method for assessing the quality of HDR treatment delivery. Further development is necessary to determine the most effective dose sampling, to ensure reproducible evaluation of treatment delivery accuracy.« less