Quality Control Guidelines for SAM Biotoxin Methods

EPA Pesticide Factsheets

Learn more about quality control guidelines and recommendations for the analysis of samples using the pathogen methods listed in EPA's Selected Analytical Methods for Environmental Remediation and Recovery (SAM).

Make no mistake—errors can be controlled*

PubMed Central

Hinckley, C

2003-01-01



 Traditional quality control methods identify "variation" as the enemy. However, the control of variation by itself can never achieve the remarkably low non-conformance rates of world class quality leaders. Because the control of variation does not achieve the highest levels of quality, an inordinate focus on these techniques obscures key quality improvement opportunities and results in unnecessary pain and suffering for patients, and embarrassment, litigation, and loss of revenue for healthcare providers. Recent experience has shown that mistakes are the most common cause of problems in health care as well as in other industrial environments. Excessive product and process complexity contributes to both excessive variation and unnecessary mistakes. The best methods for controlling variation, mistakes, and complexity are each a form of mistake proofing. Using these mistake proofing techniques, virtually every mistake and non-conformance can be controlled at a fraction of the cost of traditional quality control methods. PMID:14532368

Design, analysis, and interpretation of field quality-control data for water-sampling projects

USGS Publications Warehouse

Mueller, David K.; Schertz, Terry L.; Martin, Jeffrey D.; Sandstrom, Mark W.

2015-01-01

The report provides extensive information about statistical methods used to analyze quality-control data in order to estimate potential bias and variability in environmental data. These methods include construction of confidence intervals on various statistical measures, such as the mean, percentiles and percentages, and standard deviation. The methods are used to compare quality-control results with the larger set of environmental data in order to determine whether the effects of bias and variability might interfere with interpretation of these data. Examples from published reports are presented to illustrate how the methods are applied, how bias and variability are reported, and how the interpretation of environmental data can be qualified based on the quality-control analysis.

Quality Assurance of Chemical Measurements.

ERIC Educational Resources Information Center

Taylor, John K.

1981-01-01

Reviews aspects of quality control (methods to control errors) and quality assessment (verification that systems are operating within acceptable limits) including an analytical measurement system, quality control by inspection, control charts, systematic errors, and use of SRMs, materials for which properties are certified by the National Bureau…

Assuring Quality in Education Evaluation.

ERIC Educational Resources Information Center

Trochim, William M. K.; Visco, Ronald J.

1986-01-01

A number of quality assurance educational evaluation methods are illustrated. Evaluation data obtained from the Providence, Rhode Island, school district are used. The methods are: (1) from auditing, internal control; (2) from accounting, double bookkeeping; and (3) from industrial quality control, acceptance sampling and cumulative percentage…

A Model of Risk Analysis in Analytical Methodology for Biopharmaceutical Quality Control.

PubMed

Andrade, Cleyton Lage; Herrera, Miguel Angel De La O; Lemes, Elezer Monte Blanco

2018-01-01

One key quality control parameter for biopharmaceutical products is the analysis of residual cellular DNA. To determine small amounts of DNA (around 100 pg) that may be in a biologically derived drug substance, an analytical method should be sensitive, robust, reliable, and accurate. In principle, three techniques have the ability to measure residual cellular DNA: radioactive dot-blot, a type of hybridization; threshold analysis; and quantitative polymerase chain reaction. Quality risk management is a systematic process for evaluating, controlling, and reporting of risks that may affects method capabilities and supports a scientific and practical approach to decision making. This paper evaluates, by quality risk management, an alternative approach to assessing the performance risks associated with quality control methods used with biopharmaceuticals, using the tool hazard analysis and critical control points. This tool provides the possibility to find the steps in an analytical procedure with higher impact on method performance. By applying these principles to DNA analysis methods, we conclude that the radioactive dot-blot assay has the largest number of critical control points, followed by quantitative polymerase chain reaction, and threshold analysis. From the analysis of hazards (i.e., points of method failure) and the associated method procedure critical control points, we conclude that the analytical methodology with the lowest risk for performance failure for residual cellular DNA testing is quantitative polymerase chain reaction. LAY ABSTRACT: In order to mitigate the risk of adverse events by residual cellular DNA that is not completely cleared from downstream production processes, regulatory agencies have required the industry to guarantee a very low level of DNA in biologically derived pharmaceutical products. The technique historically used was radioactive blot hybridization. However, the technique is a challenging method to implement in a quality control laboratory: It is laborious, time consuming, semi-quantitative, and requires a radioisotope. Along with dot-blot hybridization, two alternatives techniques were evaluated: threshold analysis and quantitative polymerase chain reaction. Quality risk management tools were applied to compare the techniques, taking into account the uncertainties, the possibility of circumstances or future events, and their effects upon method performance. By illustrating the application of these tools with DNA methods, we provide an example of how they can be used to support a scientific and practical approach to decision making and can assess and manage method performance risk using such tools. This paper discusses, considering the principles of quality risk management, an additional approach to the development and selection of analytical quality control methods using the risk analysis tool hazard analysis and critical control points. This tool provides the possibility to find the method procedural steps with higher impact on method reliability (called critical control points). Our model concluded that the radioactive dot-blot assay has the larger number of critical control points, followed by quantitative polymerase chain reaction and threshold analysis. Quantitative polymerase chain reaction is shown to be the better alternative analytical methodology in residual cellular DNA analysis. © PDA, Inc. 2018.

Applying Sigma Metrics to Reduce Outliers.

PubMed

Litten, Joseph

2017-03-01

Sigma metrics can be used to predict assay quality, allowing easy comparison of instrument quality and predicting which tests will require minimal quality control (QC) rules to monitor the performance of the method. A Six Sigma QC program can result in fewer controls and fewer QC failures for methods with a sigma metric of 5 or better. The higher the number of methods with a sigma metric of 5 or better, the lower the costs for reagents, supplies, and control material required to monitor the performance of the methods. Copyright © 2016 Elsevier Inc. All rights reserved.

Some Inspection Methods for Quality Control and In-service Inspection of GLARE

NASA Astrophysics Data System (ADS)

Sinke, J.

2003-07-01

Quality control of materials and structures is an important issue, also for GLARE. During the manufacturing stage the processes and materials should be monitored and checked frequently in order to obtain a qualified product. During the operation of the aircraft, frequent monitoring and inspections are performed to maintain the quality at a prescribed level. Therefore, in-service inspection methods are applied, and when necessary repair activities are conducted. For the quality control of the GLARE panels and components during manufacturing, the C-scan method proves to be an effective tool. For in-service inspection the Eddy Current Method is one of the suitable options. In this paper a brief overview is presented of both methods and their application on GLARE products.

Controlled dehydration improves the diffraction quality of two RNA crystals.

PubMed

Park, HaJeung; Tran, Tuan; Lee, Jun Hyuck; Park, Hyun; Disney, Matthew D

2016-11-03

Post-crystallization dehydration methods, applying either vapor diffusion or humidity control devices, have been widely used to improve the diffraction quality of protein crystals. Despite the fact that RNA crystals tend to diffract poorly, there is a dearth of reports on the application of dehydration methods to improve the diffraction quality of RNA crystals. We use dehydration techniques with a Free Mounting System (FMS, a humidity control device) to recover the poor diffraction quality of RNA crystals. These approaches were applied to RNA constructs that model various RNA-mediated repeat expansion disorders. The method we describe herein could serve as a general tool to improve diffraction quality of RNA crystals to facilitate structure determinations.

40 CFR Appendix B to Part 425 - Modified Monier-Williams Method

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Modified Monier-Williams Method B... Appendix B to Part 425—Modified Monier-Williams Method Outline of Method Hydrogen sulfide is liberated from.... Quality Control 1. Each laboratory that uses this method is required to operate a formal quality control...

40 CFR Appendix B to Part 425 - Modified Monier-Williams Method

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Modified Monier-Williams Method B... Part 425—Modified Monier-Williams Method Outline of Method Hydrogen sulfide is liberated from an.... Quality Control 1. Each laboratory that uses this method is required to operate a formal quality control...

40 CFR Appendix B to Part 425 - Modified Monier-Williams Method

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Modified Monier-Williams Method B... Part 425—Modified Monier-Williams Method Outline of Method Hydrogen sulfide is liberated from an.... Quality Control 1. Each laboratory that uses this method is required to operate a formal quality control...

[Analysis and countermeasure for quality risk in process of traditional Chinese medicine preparations].

PubMed

Yang, Ming; Yang, Yuan-Zhen; Wang, Ya-Qi; Wu, Zhen-Feng; Wang, Xue-Cheng; Luo, Jing

2017-03-01

Product quality relies on not only testing methods,but also the design and development, production control and product manufacturing all aspects of logistics management. Quality comes from the process control level.Therefore, it is very important to accurately identify the factors that may induce quality risk in the production process and quality control measures correspondingly.This article systematically analyzes the source of the quality risk of all aspects of the production process in traditional Chinese medicine preparation. Discussing ways and methods of quality risk identification of traditional Chinese medicine preparation and providing references for perfecting the whole process quality management of traditional Chinese medicine preparation. Copyright© by the Chinese Pharmaceutical Association.

[Discussion on Quality Evaluation Method of Medical Device During Life-Cycle in Operation Based on the Analytic Hierarchy Process].

PubMed

Zheng, Caixian; Zheng, Kun; Shen, Yunming; Wu, Yunyun

2016-01-01

The content related to the quality during life-cycle in operation of medical device includes daily use, repair volume, preventive maintenance, quality control and adverse event monitoring. In view of this, the article aims at discussion on the quality evaluation method of medical devices during their life cycle in operation based on the Analytic Hierarchy Process (AHP). The presented method is proved to be effective by evaluating patient monitors as example. The method presented in can promote and guide the device quality control work, and it can provide valuable inputs to decisions about purchase of new device.

[Investigation on production process quality control of traditional Chinese medicine--Banlangen granule as an example].

PubMed

Tan, Manrong; Yan, Dan; Qiu, Lingling; Chen, Longhu; Yan, Yan; Jin, Cheng; Li, Hanbing; Xiao, Xiaohe

2012-04-01

For the quality management system of herbal medicines, intermediate and finished products it exists the " short board" effect of methodologies. Based on the concept of process control, new strategies and new methods of the production process quality control had been established with the consideration of the actual production of traditional Chinese medicine an the characteristics of Chinese medicine. Taking Banlangen granule as a practice example, which was effective and widespread application, character identification, determination of index components, chemical fingerprint and biometrics technology were sequentially used respectively to assess the quality of Banlangen herbal medicines, intermediate (water extraction and alcohol precipitation) and finished product. With the transfer rate of chemical information and biological potency as indicators, the effectiveness and transmission of the above different assessments and control methods had been researched. And ultimately, the process quality control methods of Banlangen granule, which were based on chemical composition analysis-biometric analysis, had been set up. It can not only validly solute the current status that there were many manufacturers varying quality of Banlangen granule, but also ensure and enhance its clinical efficacy. Furthermore it provided a foundation for the construction of the quality control of traditional Chinese medicine production process.

Control by quality: proposition of a typology.

PubMed

Pujo, P; Pillet, M

The application of Quality tools and methods in industrial management has always had a fundamental impact on the control of production. It influences the behavior of the actors concerned, while introducing the necessary notions and formalizations, especially for production systems with little or no automation, which constitute a large part of the industrial activity. Several quality approaches are applied in the workshop and are implemented at the level of the control. In this paper, the authors present a typology of the various approaches that have successively influenced control, such as statistical process control, quality assurance, and continuous improvement. First the authors present a parallel between production control and quality organizational structure. They note the duality between control, which is aimed at increasing productivity, and quality, which aims to satisfy the needs of the customer. They also note the hierarchical organizational structure of these two systems of management with, at each level, the notion of a feedback loop. This notion is fundamental to any kind of decision making. The paper is organized around the operational, tactical, and strategic levels, by describing for each level the main methods and tools for control by quality. The overview of these tools and methods starts at the operational level, with the Statistical Process Control, the Taguchi technique, and the "six sigma" approach. On the tactical level, we find a quality system approach, with a documented description of the procedures introduced in the firm. The management system can refer here to Quality Assurance, Total Productive Maintenance, or Management by Total Quality. The formalization through procedures of the rules of decision governing the process control enhances the validity of these rules. This leads to the enhancement of their reliability and to their consolidation. All this counterbalances the human, intrinsically fluctuating, behavior of the control operators. Strategic control by quality is then detailed, and the two main approaches, the continuous improvement approach and the proactive improvement approach, are introduced. Finally, the authors observe that at each of the three levels, the continuous process improvement, which is a component of Total Quality, becomes an essential preoccupation for the control. Ultimately, the recursive utilization of the Deming cycle remains the best practice for the control by quality.

Quality Control of the Print with the Application of Statistical Methods

NASA Astrophysics Data System (ADS)

Simonenko, K. V.; Bulatova, G. S.; Antropova, L. B.; Varepo, L. G.

2018-04-01

The basis for standardizing the process of offset printing is the control of print quality indicators. The solution of this problem has various approaches, among which the most important are statistical methods. Practical implementation of them for managing the quality of the printing process is very relevant and is reflected in this paper. The possibility of using the method of constructing a Control Card to identify the reasons for the deviation of the optical density for a triad of inks in offset printing is shown.

Statistical Process Control: Going to the Limit for Quality.

ERIC Educational Resources Information Center

Training, 1987

1987-01-01

Defines the concept of statistical process control, a quality control method used especially in manufacturing. Generally, concept users set specific standard levels that must be met. Makes the point that although employees work directly with the method, management is responsible for its success within the plant. (CH)

Importance of good manufacturing practices in microbiological monitoring in processing human tissues for transplant.

PubMed

Pianigiani, Elisa; Ierardi, Francesca; Fimiani, Michele

2013-12-01

Skin allografts represent an important therapeutic resource in the treatment of severe skin loss. The risk associated with application of processed tissues in humans is very low, however, human material always carries the risk of disease transmission. To minimise the risk of contamination of grafts, processing is carried out in clean rooms where air quality is monitored. Procedures and quality control tests are performed to standardise the production process and to guarantee the final product for human use. Since we only validate and distribute aseptic tissues, we conducted a study to determine what type of quality controls for skin processing are the most suitable for detecting processing errors and intercurrent contamination, and for faithfully mapping the process without unduly increasing production costs. Two different methods for quality control were statistically compared using the Fisher exact test. On the basis of the current study we selected our quality control procedure based on pre- and post-processing tissue controls, operator and environmental controls. Evaluation of the predictability of our control methods showed that tissue control was the most reliable method of revealing microbial contamination of grafts. We obtained 100 % sensitivity by doubling tissue controls, while maintaining high specificity (77 %).

Standardized methods and quality control limits for agar and broth microdilution susceptibility testing of Mycoplasma pneumoniae, Mycoplasma hominis, and Ureaplasma urealyticum.

PubMed

Waites, Ken B; Duffy, Lynn B; Bébéar, Cécile M; Matlow, Anne; Talkington, Deborah F; Kenny, George E; Totten, Patricia A; Bade, Donald J; Zheng, Xiaotian; Davidson, Maureen K; Shortridge, Virginia D; Watts, Jeffrey L; Brown, Steven D

2012-11-01

An international multilaboratory collaborative study was conducted to develop standard media and consensus methods for the performance and quality control of antimicrobial susceptibility testing of Mycoplasma pneumoniae, Mycoplasma hominis, and Ureaplasma urealyticum using broth microdilution and agar dilution techniques. A reference strain from the American Type Culture Collection was designated for each species, which was to be used for quality control purposes. Repeat testing of replicate samples of each reference strain by participating laboratories utilizing both methods and different lots of media enabled a 3- to 4-dilution MIC range to be established for drugs in several different classes, including tetracyclines, macrolides, ketolides, lincosamides, and fluoroquinolones. This represents the first multilaboratory collaboration to standardize susceptibility testing methods and to designate quality control parameters to ensure accurate and reliable assay results for mycoplasmas and ureaplasmas that infect humans.

Bioassay selection, experimental design and quality control/assurance for use in effluent assessment and control.

PubMed

Johnson, Ian; Hutchings, Matt; Benstead, Rachel; Thain, John; Whitehouse, Paul

2004-07-01

In the UK Direct Toxicity Assessment Programme, carried out in 1998-2000, a series of internationally recognised short-term toxicity test methods for algae, invertebrates and fishes, and rapid methods (ECLOX and Microtox) were used extensively. Abbreviated versions of conventional tests (algal growth inhibition tests, Daphnia magna immobilisation test and the oyster embryo-larval development test) were valuable for toxicity screening of effluent discharges and the identification of causes and sources of toxicity. Rapid methods based on chemiluminescence and bioluminescence were not generally useful in this programme, but may have a role where the rapid test has been shown to be an acceptable surrogate for a standardised test method. A range of quality assurance and control measures were identified. Requirements for quality control/assurance are most stringent when deriving data for characterising the toxic hazards of effluents and monitoring compliance against a toxicity reduction target. Lower quality control/assurance requirements can be applied to discharge screening and the identification of causes and sources of toxicity.

Image registration assessment in radiotherapy image guidance based on control chart monitoring.

PubMed

Xia, Wenyao; Breen, Stephen L

2018-04-01

Image guidance with cone beam computed tomography in radiotherapy can guarantee the precision and accuracy of patient positioning prior to treatment delivery. During the image guidance process, operators need to take great effort to evaluate the image guidance quality before correcting a patient's position. This work proposes an image registration assessment method based on control chart monitoring to reduce the effort taken by the operator. According to the control chart plotted by daily registration scores of each patient, the proposed method can quickly detect both alignment errors and image quality inconsistency. Therefore, the proposed method can provide a clear guideline for the operators to identify unacceptable image quality and unacceptable image registration with minimal effort. Experimental results demonstrate that by using control charts from a clinical database of 10 patients undergoing prostate radiotherapy, the proposed method can quickly identify out-of-control signals and find special cause of out-of-control registration events.

Off-Line Quality Control In Integrated Circuit Fabrication Using Experimental Design

NASA Astrophysics Data System (ADS)

Phadke, M. S.; Kackar, R. N.; Speeney, D. V.; Grieco, M. J.

1987-04-01

Off-line quality control is a systematic method of optimizing production processes and product designs. It is widely used in Japan to produce high quality products at low cost. The method was introduced to us by Professor Genichi Taguchi who is a Deming-award winner and a former Director of the Japanese Academy of Quality. In this paper we will i) describe the off-line quality control method, and ii) document our efforts to optimize the process for forming contact windows in 3.5 Aim CMOS circuits fabricated in the Murray Hill Integrated Circuit Design Capability Laboratory. In the fabrication of integrated circuits it is critically important to produce contact windows of size very near the target dimension. Windows which are too small or too large lead to loss of yield. The off-line quality control method has improved both the process quality and productivity. The variance of the window size has been reduced by a factor of four. Also, processing time for window photolithography has been substantially reduced. The key steps of off-line quality control are: i) Identify important manipulatable process factors and their potential working levels. ii) Perform fractional factorial experiments on the process using orthogonal array designs. iii) Analyze the resulting data to determine the optimum operating levels of the factors. Both the process mean and the process variance are considered in this analysis. iv) Conduct an additional experiment to verify that the new factor levels indeed give an improvement.

Evaluation of thin-layer chromatography methods for quality control of commercial products containing Aesculus hippocastanum, Turnera diffusa, Matricaria recutita, Passiflora incarnata, and Tilia occidentalis.

PubMed

Ramírez-Durón, Rosalba; Ceniceros-Almaguer, Lucía; Salazar-Aranda, Ricardo; Salazar-Cavazos, Ma de la Luz; Waksman de Torres, Noemi

2007-01-01

In Mexico, plant-derived products with health claims are sold as herbal dietary supplements, and there are no rules for their legal quality control. Aesculus hippocastanum, Turnera diffusa, Matricaria recutita, Passiflora incarnata, and Tilia occidentalis are some of the major commercial products obtained from plants used in this region. In this paper, we describe the effectiveness of thin-layer chromatography methods to provide for the quality control of several commercial products containing these plants. Standardized extracts were used. Of the 49 commercial products analyzed, only 32.65% matched the chromatographic characteristic of standardized extracts. A significant number of commercial products did not match their label, indicating a problem resulting from the lack of regulation for these products. The proposed methods are simple, sensitive, and specific and can be used for routine quality control of raw herbals and formulations of the tested plants. The results obtained show the need to develop simple and reliable analytical methods that can be performed in any laboratory for the purpose of quality control of dietary supplements or commercial herbal products sold in Mexico.

Guidelines for the detection of Trichinella larvae at the slaughterhouse in a quality assurance system.

PubMed

Rossi, Patrizia; Pozio, Edoardo

2008-01-01

The European Community Regulation (EC) No. 2075/2005 lays down specific rules on official controls for the detection of Trichinella in fresh meat for human consumption, recommending the pooled-sample digestion method as the reference method. The aim of this document is to provide specific guidance to implement an appropriate Trichinella digestion method by a laboratory accredited according to the ISO/IEC 17025:2005 international standard, and performing microbiological testing following the EA-04/10:2002 international guideline. Technical requirements for the correct implementation of the method, such as the personnel competence, specific equipments and reagents, validation of the method, reference materials, sampling, quality assurance of results and quality control of performance are provided, pointing out the critical control points for the correct implementation of the digestion method.

Analytic Methods Used in Quality Control in a Compounding Pharmacy.

PubMed

Allen, Loyd V

2017-01-01

Analytical testing will no doubt become a more important part of pharmaceutical compounding as the public and regulatory agencies demand increasing documentation of the quality of compounded preparations. Compounding pharmacists must decide what types of testing and what amount of testing to include in their quality-control programs, and whether testing should be done in-house or outsourced. Like pharmaceutical compounding, analytical testing should be performed only by those who are appropriately trained and qualified. This article discusses the analytical methods that are used in quality control in a compounding pharmacy. Copyright© by International Journal of Pharmaceutical Compounding, Inc.

Interrupted Time Series Versus Statistical Process Control in Quality Improvement Projects.

PubMed

Andersson Hagiwara, Magnus; Andersson Gäre, Boel; Elg, Mattias

2016-01-01

To measure the effect of quality improvement interventions, it is appropriate to use analysis methods that measure data over time. Examples of such methods include statistical process control analysis and interrupted time series with segmented regression analysis. This article compares the use of statistical process control analysis and interrupted time series with segmented regression analysis for evaluating the longitudinal effects of quality improvement interventions, using an example study on an evaluation of a computerized decision support system.

Multi-criteria decision making approaches for quality control of genome-wide association studies.

PubMed

Malovini, Alberto; Rognoni, Carla; Puca, Annibale; Bellazzi, Riccardo

2009-03-01

Experimental errors in the genotyping phases of a Genome-Wide Association Study (GWAS) can lead to false positive findings and to spurious associations. An appropriate quality control phase could minimize the effects of this kind of errors. Several filtering criteria can be used to perform quality control. Currently, no formal methods have been proposed for taking into account at the same time these criteria and the experimenter's preferences. In this paper we propose two strategies for setting appropriate genotyping rate thresholds for GWAS quality control. These two approaches are based on the Multi-Criteria Decision Making theory. We have applied our method on a real dataset composed by 734 individuals affected by Arterial Hypertension (AH) and 486 nonagenarians without history of AH. The proposed strategies appear to deal with GWAS quality control in a sound way, as they lead to rationalize and make explicit the experimenter's choices thus providing more reproducible results.

A system framework of inter-enterprise machining quality control based on fractal theory

NASA Astrophysics Data System (ADS)

Zhao, Liping; Qin, Yongtao; Yao, Yiyong; Yan, Peng

2014-03-01

In order to meet the quality control requirement of dynamic and complicated product machining processes among enterprises, a system framework of inter-enterprise machining quality control based on fractal was proposed. In this system framework, the fractal-specific characteristic of inter-enterprise machining quality control function was analysed, and the model of inter-enterprise machining quality control was constructed by the nature of fractal structures. Furthermore, the goal-driven strategy of inter-enterprise quality control and the dynamic organisation strategy of inter-enterprise quality improvement were constructed by the characteristic analysis on this model. In addition, the architecture of inter-enterprise machining quality control based on fractal was established by means of Web service. Finally, a case study for application was presented. The result showed that the proposed method was available, and could provide guidance for quality control and support for product reliability in inter-enterprise machining processes.

Statistical Methods in Assembly Quality Management of Multi-Element Products on Automatic Rotor Lines

NASA Astrophysics Data System (ADS)

Pries, V. V.; Proskuriakov, N. E.

2018-04-01

To control the assembly quality of multi-element mass-produced products on automatic rotor lines, control methods with operational feedback are required. However, due to possible failures in the operation of the devices and systems of automatic rotor line, there is always a real probability of getting defective (incomplete) products into the output process stream. Therefore, a continuous sampling control of the products completeness, based on the use of statistical methods, remains an important element in managing the quality of assembly of multi-element mass products on automatic rotor lines. The feature of continuous sampling control of the multi-element products completeness in the assembly process is its breaking sort, which excludes the possibility of returning component parts after sampling control to the process stream and leads to a decrease in the actual productivity of the assembly equipment. Therefore, the use of statistical procedures for continuous sampling control of the multi-element products completeness when assembled on automatic rotor lines requires the use of such sampling plans that ensure a minimum size of control samples. Comparison of the values of the limit of the average output defect level for the continuous sampling plan (CSP) and for the automated continuous sampling plan (ACSP) shows the possibility of providing lower limit values for the average output defects level using the ACSP-1. Also, the average sample size when using the ACSP-1 plan is less than when using the CSP-1 plan. Thus, the application of statistical methods in the assembly quality management of multi-element products on automatic rotor lines, involving the use of proposed plans and methods for continuous selective control, will allow to automating sampling control procedures and the required level of quality of assembled products while minimizing sample size.

A method for evaluating treatment quality using in vivo EPID dosimetry and statistical process control in radiation therapy.

PubMed

Fuangrod, Todsaporn; Greer, Peter B; Simpson, John; Zwan, Benjamin J; Middleton, Richard H

2017-03-13

Purpose Due to increasing complexity, modern radiotherapy techniques require comprehensive quality assurance (QA) programmes, that to date generally focus on the pre-treatment stage. The purpose of this paper is to provide a method for an individual patient treatment QA evaluation and identification of a "quality gap" for continuous quality improvement. Design/methodology/approach A statistical process control (SPC) was applied to evaluate treatment delivery using in vivo electronic portal imaging device (EPID) dosimetry. A moving range control chart was constructed to monitor the individual patient treatment performance based on a control limit generated from initial data of 90 intensity-modulated radiotherapy (IMRT) and ten volumetric-modulated arc therapy (VMAT) patient deliveries. A process capability index was used to evaluate the continuing treatment quality based on three quality classes: treatment type-specific, treatment linac-specific, and body site-specific. Findings The determined control limits were 62.5 and 70.0 per cent of the χ pass-rate for IMRT and VMAT deliveries, respectively. In total, 14 patients were selected for a pilot study the results of which showed that about 1 per cent of all treatments contained errors relating to unexpected anatomical changes between treatment fractions. Both rectum and pelvis cancer treatments demonstrated process capability indices were less than 1, indicating the potential for quality improvement and hence may benefit from further assessment. Research limitations/implications The study relied on the application of in vivo EPID dosimetry for patients treated at the specific centre. Sampling patients for generating the control limits were limited to 100 patients. Whilst the quantitative results are specific to the clinical techniques and equipment used, the described method is generally applicable to IMRT and VMAT treatment QA. Whilst more work is required to determine the level of clinical significance, the authors have demonstrated the capability of the method for both treatment specific QA and continuing quality improvement. Practical implications The proposed method is a valuable tool for assessing the accuracy of treatment delivery whilst also improving treatment quality and patient safety. Originality/value Assessing in vivo EPID dosimetry with SPC can be used to improve the quality of radiation treatment for cancer patients.

The method of quality marker research and quality evaluation of traditional Chinese medicine based on drug properties and effect characteristics.

PubMed

Zhang, Tiejun; Bai, Gang; Han, Yanqi; Xu, Jun; Gong, Suxiao; Li, Yazhuo; Zhang, Hongbing; Liu, Changxiao

2018-05-15

Quality of traditional Chinese medicine (TCM) plays a critical role in industry of TCM. Rapid development of TCM pharmaceutical areas is, however, greatly limited, since there are many issues not been resolved, concerning the quality study of TCM. Core concept of TCM quality as well as the characteristics of TCM was discussed, in order to guide the quality research and evaluation of TCM, further improve the level of TCM quality control. In this review, on the basis of systematic analysis of fundamental property and features of TCM in clinical application, the approaches and methods of quality marker (Q-marker) study were proposed through combination of transitivity and traceability of essentials of quality, correlation between chemical ingredients and drug property/efficacy, as well as analysis of endemicity of ingredients sharing similar pharmacophylogenetic and biosynthetic approaches. The approaches and methods of Q-marker study were proposed and the novel integrated pattern for quality assessment and control of TCM was established. The core concept of Q-marker has helped to break through the bottleneck of the current fragmented quality research of TCM and improved the scientificity, integrity and systematicness of quality control. Copyright © 2018 Elsevier GmbH. All rights reserved.

Analysis and quality control of carbohydrates in therapeutic proteins with fluorescence HPLC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Kun; Huang, Jian; Center for Informational Biology, University of Electronic Science and Technology of China, Chengdu 610054

Conbercept is an Fc fusion protein with very complicated carbohydrate profiles which must be carefully monitored through manufacturing process. Here, we introduce an optimized fluorescence derivatization high-performance liquid chromatographic method for glycan mapping in conbercept. Compared with conventional glycan analysis method, this method has much better resolution and higher reproducibility making it excellent for product quality control.

The model of flood control using servqual method and importance performance analysis in Surakarta City – Indonesia

NASA Astrophysics Data System (ADS)

Titi Purwantini, V.; Sutanto, Yusuf

2018-05-01

This research is to create a model of flood control in the city of Surakarta using Servqual method and Importance Performance Analysis. Service quality is generally defined as the overall assessment of a service by the customersor the extent to which a service meets customer’s needs or expectations. The purpose of this study is to find the first model of flood control that is appropriate to the condition of the community. Surakarta This means looking for a model that can provide satisfactory service for the people of Surakarta who are in the location of the flood. The second is to find the right model to improve service performance of Surakarta City Government in serving the people in flood location. The method used to determine the satisfaction of the public on the quality of service is to see the difference in the quality of service expected by the community with the reality. This method is Servqual Method While to assess the performance of city government officials is by comparing the actual performance with the quality of services provided, this method is This means looking for a model that can provide satisfactory service for the people of Surakarta who are in the location of the flood.The second is to find the right model to improve service performance of Surakarta City Government in serving the people in flood location. The method used to determine the satisfaction of the public on the quality of service is to see the difference in the quality of service expected by the community with the reality. This method is Servqual Method While to assess the performance of city government officials is by comparing the actual performance with the quality of services provided, this method is Importance Performance Analysis. Samples were people living in flooded areas in the city of Surakarta. Result this research is Satisfaction = Responsiveness+ Realibility + Assurance + Empathy+ Tangible (Servqual Model) and Importance Performance Analysis is From Cartesian diagram can be made Flood Control Formula as follow: Food Control = High performance

Current status of quality evaluation of nursing care through director review and reflection from the Nursing Quality Control Centers

PubMed Central

Duan, Xia; Shi, Yan

2014-01-01

Background: The quality evaluation of nursing care is a key link in medical quality management. It is important and worth studying for the nursing supervisors to know the disadvantages during the process of quality evaluation of nursing care and then to improve the whole nursing quality. This study was to provide director insight on the current status of quality evaluation of nursing care from Nursing Quality Control Centers (NQCCs). Material and Methods: This qualitative study used a sample of 12 directors from NQCCs who were recruited from 12 provinces in China to evaluate the current status of quality evaluation of nursing care. Data were collected by in-depth interviews. Content analysis method was used to analyze the data. Results: Four themes emerged from the data: 1) lag of evaluation index; 2) limitations of evaluation content; 3) simplicity of evaluation method; 4) excessive emphasis on terminal quality. Conclusion: It is of great realistic significance to ameliorate nursing quality evaluation criteria, modify the evaluation content based on patient needs-oriented idea, adopt scientific evaluation method to evaluate nursing quality, and scientifically and reasonably draw horizontal comparisons of nursing quality between hospitals, as well as longitudinal comparisons of a hospital’s nursing quality. These methods mentioned above can all enhance a hospital’s core competitiveness and benefit more patients. PMID:25419427

Total Quality Management Guide. Volume 2. A Guide to Implementation

DTIC Science & Technology

1990-02-15

Kaoru . Guide to Quality Control. Asian Productivity Organization. 1984. Ishikawa , Kaoru . What is Total Quality Control? The Japanese Way. Englewood...of the new Systems Age. The theories of Deming, Juran, Ishikawa , and other management methods that still predominate are pioneers of Systems Age...Feigenbaum, Armand V. Total Quality Control. New York: McGraw-Hill Book Company. 1983. bnai, Masaaki. Kaizen. New York: Random House. 1986. Ishikawa

New patient-controlled abdominal compression method in radiography: radiation dose and image quality.

PubMed

Piippo-Huotari, Oili; Norrman, Eva; Anderzén-Carlsson, Agneta; Geijer, Håkan

2018-05-01

The radiation dose for patients can be reduced with many methods and one way is to use abdominal compression. In this study, the radiation dose and image quality for a new patient-controlled compression device were compared with conventional compression and compression in the prone position . To compare radiation dose and image quality of patient-controlled compression compared with conventional and prone compression in general radiography. An experimental design with quantitative approach. After obtaining the approval of the ethics committee, a consecutive sample of 48 patients was examined with the standard clinical urography protocol. The radiation doses were measured as dose-area product and analyzed with a paired t-test. The image quality was evaluated by visual grading analysis. Four radiologists evaluated each image individually by scoring nine criteria modified from the European quality criteria for diagnostic radiographic images. There was no significant difference in radiation dose or image quality between conventional and patient-controlled compression. Prone position resulted in both higher dose and inferior image quality. Patient-controlled compression gave similar dose levels as conventional compression and lower than prone compression. Image quality was similar with both patient-controlled and conventional compression and was judged to be better than in the prone position.

Computer program CDCID: an automated quality control program using CDC update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singer, G.L.; Aguilar, F.

1984-04-01

A computer program, CDCID, has been developed in coordination with a quality control program to provide a highly automated method of documenting changes to computer codes at EG and G Idaho, Inc. The method uses the standard CDC UPDATE program in such a manner that updates and their associated documentation are easily made and retrieved in various formats. The method allows each card image of a source program to point to the document which describes it, who created the card, and when it was created. The method described is applicable to the quality control of computer programs in general. Themore » computer program described is executable only on CDC computing systems, but the program could be modified and applied to any computing system with an adequate updating program.« less

[Quality control at the Istituto di Anatomia e Istologia patologica at the Università di Bologna].

PubMed

Alampi, G; Baroni, R; Berti, E; Ceccarelli, C; Dina, R; Eusebi, V; Giangaspero, F; Grigioni, F W; Lecce, S; Losi, L

1994-04-01

The growing importance in medical practice of a standardized diagnosis in cyto- and histopathology and the recent recommendations for the adoption of standardized schemes for quality control in anatomic pathology by International Committees stimulated the medical staff of the Institute of Anatomic Pathology of the University of Bologna to adopt a pertinent method. The method used by the Department of Pathology of the Yale University (New Haven, Connecticut, USA) was chosen. A Committee for the quality control was appointed and two kinds of controls were set up: an External Quality Assessment (review of the difficult cases by external experts, slide seminars) and an Internal Quality Assessment performed by the members of the Committee on the diagnostic and laboratory routine of the Institute. Such a survey is periodically monitored during the monthly meetings of the Committee and described in the monthly reports. The present paper illustrates the method adopted and the preliminary results obtained in order to stimulate the discussion of such a critical theme in contemporary Anatomic Pathology at a national level.

A novel Python program for implementation of quality control in the ELISA.

PubMed

Wetzel, Hanna N; Cohen, Cinder; Norman, Andrew B; Webster, Rose P

2017-09-01

The use of semi-quantitative assays such as the enzyme-linked immunosorbent assay (ELISA) requires stringent quality control of the data. However, such quality control is often lacking in academic settings due to unavailability of software and knowledge. Therefore, our aim was to develop methods to easily implement Levey-Jennings quality control methods. For this purpose, we created a program written in Python (a programming language with an open-source license) and tested it using a training set of ELISA standard curves quantifying the Fab fragment of an anti-cocaine monoclonal antibody in mouse blood. A colorimetric ELISA was developed using a goat anti-human anti-Fab capture method. Mouse blood samples spiked with the Fab fragment were tested against a standard curve of known concentrations of Fab fragment in buffer over a period of 133days stored at 4°C to assess stability of the Fab fragment and to generate a test dataset to assess the program. All standard curves were analyzed using our program to batch process the data and to generate Levey-Jennings control charts and statistics regarding the datasets. The program was able to identify values outside of two standard deviations, and this identification of outliers was consistent with the results of a two-way ANOVA. This program is freely available, which will help laboratories implement quality control methods, thus improving reproducibility within and between labs. We report here successful testing of the program with our training set and development of a method for quantification of the Fab fragment in mouse blood. Copyright © 2017 Elsevier B.V. All rights reserved.

Assessing the influence of component processing and donor characteristics on quality of red cell concentrates using quality control data.

PubMed

Jordan, A; Chen, D; Yi, Q-L; Kanias, T; Gladwin, M T; Acker, J P

2016-07-01

Quality control (QC) data collected by blood services are used to monitor production and to ensure compliance with regulatory standards. We demonstrate how analysis of quality control data can be used to highlight the sources of variability within red cell concentrates (RCCs). We merged Canadian Blood Services QC data with manufacturing and donor records for 28 227 RCC between June 2011 and October 2014. Units were categorized based on processing method, bag manufacturer, donor age and donor sex, then assessed based on product characteristics: haemolysis and haemoglobin levels, unit volume, leucocyte count and haematocrit. Buffy-coat method (top/bottom)-processed units exhibited lower haemolysis than units processed using the whole-blood filtration method (top/top). Units from female donors exhibited lower haemolysis than male donations. Processing method influenced unit volume and the ratio of additive solution to residual plasma. Stored red blood cell characteristics are influenced by prestorage processing and donor factors. Understanding the relationship between processing, donors and RCC quality will help blood services to ensure the safety of transfused products. © 2016 International Society of Blood Transfusion.

Multi-Criteria Decision Making Approaches for Quality Control of Genome-Wide Association Studies

PubMed Central

Malovini, Alberto; Rognoni, Carla; Puca, Annibale; Bellazzi, Riccardo

2009-01-01

Experimental errors in the genotyping phases of a Genome-Wide Association Study (GWAS) can lead to false positive findings and to spurious associations. An appropriate quality control phase could minimize the effects of this kind of errors. Several filtering criteria can be used to perform quality control. Currently, no formal methods have been proposed for taking into account at the same time these criteria and the experimenter’s preferences. In this paper we propose two strategies for setting appropriate genotyping rate thresholds for GWAS quality control. These two approaches are based on the Multi-Criteria Decision Making theory. We have applied our method on a real dataset composed by 734 individuals affected by Arterial Hypertension (AH) and 486 nonagenarians without history of AH. The proposed strategies appear to deal with GWAS quality control in a sound way, as they lead to rationalize and make explicit the experimenter’s choices thus providing more reproducible results. PMID:21347174

Linking fish tolerance to water quality criteria for the assessment of environmental flows: A practical method for streamflow regulation and pollution control.

PubMed

Zhao, Changsen; Yang, Shengtian; Liu, Junguo; Liu, Changming; Hao, Fanghua; Wang, Zhonggen; Zhang, Huitong; Song, Jinxi; Mitrovic, Simon M; Lim, Richard P

2018-05-15

The survival of aquatic biota in stream ecosystems depends on both water quantity and quality, and is particularly susceptible to degraded water quality in regulated rivers. Maintenance of environmental flows (e-flows) for aquatic biota with optimum water quantity and quality is essential for sustainable ecosystem services, especially in developing regions with insufficient stream monitoring of hydrology, water quality and aquatic biota. Few e-flow methods are available that closely link aquatic biota tolerances to pollutant concentrations in a simple and practical manner. In this paper a new method was proposed to assess e-flows that aimed to satisfy the requirements of aquatic biota for both the quantity and quality of the streamflow by linking fish tolerances to water quality criteria, or the allowable concentration of pollutants. For better operation of water projects and control of pollutants discharged into streams, this paper presented two coefficients for streamflow adjustment and pollutant control. Assessment of e-flows in the Wei River, the largest tributary of the Yellow River, shows that streamflow in dry seasons failed to meet e-flow requirements. Pollutant influx exerted a large pressure on the aquatic ecosystem, with pollutant concentrations much higher than that of the fish tolerance thresholds. We found that both flow velocity and water temperature exerted great influences on the pollutant degradation rate. Flow velocity had a much greater influence on pollutant degradation than did the standard deviation of flow velocity. This study provides new methods to closely link the tolerance of aquatic biota to water quality criteria for e-flow assessment. The recommended coefficients for streamflow adjustment and pollutant control, to dynamically regulate streamflow and control pollutant discharge, are helpful for river management and ecosystems rehabilitation. The relatively low data requirement also makes the method easy to use efficiently in developing regions, and thus this study has significant implications for managing flows in polluted and regulated rivers worldwide. Copyright © 2018. Published by Elsevier Ltd.

Applications of flight control system methods to an advanced combat rotorcraft

NASA Technical Reports Server (NTRS)

Tischler, Mark B.; Fletcher, Jay W.; Morris, Patrick M.; Tucker, George T.

1989-01-01

Advanced flight control system design, analysis, and testing methodologies developed at the Ames Research Center are applied in an analytical and flight test evaluation of the Advanced Digital Optical Control System (ADOCS) demonstrator. The primary objectives are to describe the knowledge gained about the implications of digital flight control system design for rotorcraft, and to illustrate the analysis of the resulting handling-qualities in the context of the proposed new handling-qualities specification for rotorcraft. Topics covered in-depth are digital flight control design and analysis methods, flight testing techniques, ADOCS handling-qualities evaluation results, and correlation of flight test results with analytical models and the proposed handling-qualities specification. The evaluation of the ADOCS demonstrator indicates desirable response characteristics based on equivalent damping and frequency, but undersirably large effective time-delays (exceeding 240 m sec in all axes). Piloted handling-qualities are found to be desirable or adequate for all low, medium, and high pilot gain tasks; but handling-qualities are inadequate for ultra-high gain tasks such as slope and running landings.

Quantification of histochemical stains using whole slide imaging: development of a method and demonstration of its usefulness in laboratory quality control.

PubMed

Gray, Allan; Wright, Alex; Jackson, Pete; Hale, Mike; Treanor, Darren

2015-03-01

Histochemical staining of tissue is a fundamental technique in tissue diagnosis and research, but it suffers from significant variability. Efforts to address this include laboratory quality controls and quality assurance schemes, but these rely on subjective interpretation of stain quality, are laborious and have low reproducibility. We aimed (1) to develop a method for histochemical stain quantification using whole slide imaging and image analysis and (2) to demonstrate its usefulness in measuring staining variation. A method to quantify the individual stain components of histochemical stains on virtual slides was developed. It was evaluated for repeatability and reproducibility, then applied to control sections of an appendix to quantify H&E staining (H/E intensities and H:E ratio) between automated staining machines and to measure differences between six regional diagnostic laboratories. The method was validated with <0.5% variation in H:E ratio measurement when using the same scanner for a batch of slides (ie, it was repeatable) but was not highly reproducible between scanners or over time, where variation of 7% was found. Application of the method showed H:E ratios between three staining machines varied from 0.69 to 0.93, H:E ratio variation over time was observed. Interlaboratory comparison demonstrated differences in H:E ratio between regional laboratories from 0.57 to 0.89. A simple method using whole slide imaging can be used to quantify and compare histochemical staining. This method could be deployed in routine quality assurance and quality control. Work is needed on whole slide imaging devices to improve reproducibility. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Modelling and control for laser based welding processes: modern methods of process control to improve quality of laser-based joining methods

NASA Astrophysics Data System (ADS)

Zäh, Ralf-Kilian; Mosbach, Benedikt; Hollwich, Jan; Faupel, Benedikt

2017-02-01

To ensure the competitiveness of manufacturing companies it is indispensable to optimize their manufacturing processes. Slight variations of process parameters and machine settings have only marginally effects on the product quality. Therefore, the largest possible editing window is required. Such parameters are, for example, the movement of the laser beam across the component for the laser keyhole welding. That`s why it is necessary to keep the formation of welding seams within specified limits. Therefore, the quality of laser welding processes is ensured, by using post-process methods, like ultrasonic inspection, or special in-process methods. These in-process systems only achieve a simple evaluation which shows whether the weld seam is acceptable or not. Furthermore, in-process systems use no feedback for changing the control variables such as speed of the laser or adjustment of laser power. In this paper the research group presents current results of the research field of Online Monitoring, Online Controlling and Model predictive controlling in laser welding processes to increase the product quality. To record the characteristics of the welding process, tested online methods are used during the process. Based on the measurement data, a state space model is ascertained, which includes all the control variables of the system. Depending on simulation tools the model predictive controller (MPC) is designed for the model and integrated into an NI-Real-Time-System.

The Manufacture, Shipping and Receiving and Quality Control of Rodent Bedding Materials

NASA Technical Reports Server (NTRS)

Kraft, Lisbeth M.

1980-01-01

The criteria for rodent bedding and nesting materials are discussed. The literature is reviewed regarding sources of bedding materials, manufacturing methods, quality control, procedures (microbiological, physical and chemical), storage, methods, shipment, methods of use and disposal, current knowledge concerning bedding effects on animals as related to research and testing and legal aspects. Future needs, especially with respect to the promulgation of standards, also are addressed.

Assessment of a novel multi-array normalization method based on spike-in control probes suitable for microRNA datasets with global decreases in expression.

PubMed

Sewer, Alain; Gubian, Sylvain; Kogel, Ulrike; Veljkovic, Emilija; Han, Wanjiang; Hengstermann, Arnd; Peitsch, Manuel C; Hoeng, Julia

2014-05-17

High-quality expression data are required to investigate the biological effects of microRNAs (miRNAs). The goal of this study was, first, to assess the quality of miRNA expression data based on microarray technologies and, second, to consolidate it by applying a novel normalization method. Indeed, because of significant differences in platform designs, miRNA raw data cannot be normalized blindly with standard methods developed for gene expression. This fundamental observation motivated the development of a novel multi-array normalization method based on controllable assumptions, which uses the spike-in control probes to adjust the measured intensities across arrays. Raw expression data were obtained with the Exiqon dual-channel miRCURY LNA™ platform in the "common reference design" and processed as "pseudo-single-channel". They were used to apply several quality metrics based on the coefficient of variation and to test the novel spike-in controls based normalization method. Most of the considerations presented here could be applied to raw data obtained with other platforms. To assess the normalization method, it was compared with 13 other available approaches from both data quality and biological outcome perspectives. The results showed that the novel multi-array normalization method reduced the data variability in the most consistent way. Further, the reliability of the obtained differential expression values was confirmed based on a quantitative reverse transcription-polymerase chain reaction experiment performed for a subset of miRNAs. The results reported here support the applicability of the novel normalization method, in particular to datasets that display global decreases in miRNA expression similarly to the cigarette smoke-exposed mouse lung dataset considered in this study. Quality metrics to assess between-array variability were used to confirm that the novel spike-in controls based normalization method provided high-quality miRNA expression data suitable for reliable downstream analysis. The multi-array miRNA raw data normalization method was implemented in an R software package called ExiMiR and deposited in the Bioconductor repository.

Assessment of a novel multi-array normalization method based on spike-in control probes suitable for microRNA datasets with global decreases in expression

PubMed Central

2014-01-01

Background High-quality expression data are required to investigate the biological effects of microRNAs (miRNAs). The goal of this study was, first, to assess the quality of miRNA expression data based on microarray technologies and, second, to consolidate it by applying a novel normalization method. Indeed, because of significant differences in platform designs, miRNA raw data cannot be normalized blindly with standard methods developed for gene expression. This fundamental observation motivated the development of a novel multi-array normalization method based on controllable assumptions, which uses the spike-in control probes to adjust the measured intensities across arrays. Results Raw expression data were obtained with the Exiqon dual-channel miRCURY LNA™ platform in the “common reference design” and processed as “pseudo-single-channel”. They were used to apply several quality metrics based on the coefficient of variation and to test the novel spike-in controls based normalization method. Most of the considerations presented here could be applied to raw data obtained with other platforms. To assess the normalization method, it was compared with 13 other available approaches from both data quality and biological outcome perspectives. The results showed that the novel multi-array normalization method reduced the data variability in the most consistent way. Further, the reliability of the obtained differential expression values was confirmed based on a quantitative reverse transcription–polymerase chain reaction experiment performed for a subset of miRNAs. The results reported here support the applicability of the novel normalization method, in particular to datasets that display global decreases in miRNA expression similarly to the cigarette smoke-exposed mouse lung dataset considered in this study. Conclusions Quality metrics to assess between-array variability were used to confirm that the novel spike-in controls based normalization method provided high-quality miRNA expression data suitable for reliable downstream analysis. The multi-array miRNA raw data normalization method was implemented in an R software package called ExiMiR and deposited in the Bioconductor repository. PMID:24886675

Root Cause Analysis of Quality Defects Using HPLC-MS Fingerprint Knowledgebase for Batch-to-batch Quality Control of Herbal Drugs.

PubMed

Yan, Binjun; Fang, Zhonghua; Shen, Lijuan; Qu, Haibin

2015-01-01

The batch-to-batch quality consistency of herbal drugs has always been an important issue. To propose a methodology for batch-to-batch quality control based on HPLC-MS fingerprints and process knowledgebase. The extraction process of Compound E-jiao Oral Liquid was taken as a case study. After establishing the HPLC-MS fingerprint analysis method, the fingerprints of the extract solutions produced under normal and abnormal operation conditions were obtained. Multivariate statistical models were built for fault detection and a discriminant analysis model was built using the probabilistic discriminant partial-least-squares method for fault diagnosis. Based on multivariate statistical analysis, process knowledge was acquired and the cause-effect relationship between process deviations and quality defects was revealed. The quality defects were detected successfully by multivariate statistical control charts and the type of process deviations were diagnosed correctly by discriminant analysis. This work has demonstrated the benefits of combining HPLC-MS fingerprints, process knowledge and multivariate analysis for the quality control of herbal drugs. Copyright © 2015 John Wiley & Sons, Ltd.

[Quality control assessments of feces examination for schistosomiasis in province-level laboratories of Zhejiang Province].

PubMed

Chen, Wen; Zhu, Ming-Dong; Yan, Xiao-Lan; Lin, Li-Jun; Zhang, Jian-Feng; Li, Li; Wen, Li-Yong

2011-06-01

To understand and evaluate the quality of feces examination for schistosomiasis in province-level laboratories of Zhejiang Province. With the single-blind method, the stool samples were detected by the stool hatching method and sediment detection method. In the 3 quality control assessments in 2006, 2008 and 2009, most laboratories finished the examinations on time. The accordance rates of detections were 88.9%, 100% and 93.9%, respectively. The province-level laboratories for schistosomiasis feces examination of Zhejiang Province is coming into standardization, and the techniques of schistosomiasis feces examination are optimized gradually.

Quality data collection and management technology of aerospace complex product assembly process

NASA Astrophysics Data System (ADS)

Weng, Gang; Liu, Jianhua; He, Yongxi; Zhuang, Cunbo

2017-04-01

Aiming at solving problems of difficult management and poor traceability for discrete assembly process quality data, a data collection and management method is proposed which take the assembly process and BOM as the core. Data collection method base on workflow technology, data model base on BOM and quality traceability of assembly process is included in the method. Finally, assembly process quality data management system is developed and effective control and management of quality information for complex product assembly process is realized.

A novel cell line generated using the CRISPR/Cas9 technology as universal quality control material for KRAS G12V mutation testing.

PubMed

Jia, Shiyu; Zhang, Rui; Lin, Guigao; Peng, Rongxue; Gao, Peng; Han, Yanxi; Fu, Yu; Ding, Jiansheng; Wu, Qisheng; Zhang, Kuo; Xie, Jiehong; Li, Jinming

2018-06-01

KRAS mutations are the key indicator for EGFR monoclonal antibody-targeted therapy and acquired drug resistance, and their accurate detection is critical to the clinical decision-making of colorectal cancer. However, no proper quality control material is available for the current detection methods, particularly next-generation sequencing (NGS). The ideal quality control material for NGS needs to provide both the tumor mutation gene and the matched background genomic DNA, which is uncataloged in public databases, to accurately distinguish germline polymorphisms and somatic mutations. We developed a novel KRAS G12V mutant cell line using the clustered regularly interspaced short palindromic repeat (CRISPR)/CRISPR-associated protein 9 (Cas9) technique to make up for the deficiencies in existing quality control material and further validated the feasibility of the cell line as quality control material by amplification refractory mutation system (ARMS), Sanger sequencing, digital PCR (dPCR), and NGS. We verified that the edited cell line specifically had the G12V mutation, and the validation results presented a high consistency among the four methods of detection. The three cell lines screened contained the G12V mutation and the mutation allele fractions of G12V-1, G12V-2, and G12V-3 were 52.01%, 82.06%, and 17.29%, respectively. The novel KRAS G12V cell line generated using the CRISPR/Cas9 gene editing system is suitable as a quality control material for all current detection methods and provides a new direction in the development of quality control material. © 2018 Wiley Periodicals, Inc.

A New Quality Control Method base on IRMCD for Wind Profiler Observation towards Future Assimilation Application

NASA Astrophysics Data System (ADS)

Chen, Min; Zhang, Yu

2017-04-01

A wind profiler network with a total of 65 profiling radars was operated by the MOC/CMA in China until July 2015. In this study, a quality control procedure is constructed to incorporate the profiler data from the wind-profiling network into the local data assimilation and forecasting system (BJRUC). The procedure applies a blacklisting check that removes stations with gross errors and an outlier check that rejects data with large deviations from the background. Instead of the bi-weighting method, which has been commonly implemented in outlier elimination for one-dimensional scalar observations, an outlier elimination method is developed based on the iterated reweighted minimum covariance determinant (IRMCD) for multi-variate observations such as wind profiler data. A quality control experiment is separately performed for subsets containing profiler data tagged in parallel with/without rain flags at every 00UTC/12UTC from 20 June to 30 Sep 2015. From the results, we find that with the quality control, the frequency distributions of the differences between the observations and model background become more Gaussian-like and meet the requirements of a Gaussian distribution for data assimilation. Further intensive assessment for each quality control step reveals that the stations rejected by blacklisting contain poor data quality, and the IRMCD rejects outliers in a robust and physically reasonable manner.

A Novel Diffusion MRI Phantom, and a Method for Enhancing MR Image Quality | NCI Technology Transfer Center | TTC

Cancer.gov

The use of Polyvinyl Pyrrolidone (PVP) solutions of varying concentrations as phantoms for diffusion MRI calibration and quality control is disclosed. This diffusion MRI phantom material is already being adopted by radiologists for quality control and assurance in clinical studies.

CTEPP STANDARD OPERATING PROCEDURE FOR CONDUCTING INTERNAL FIELD AUDITS AND QUALITY CONTROL (SOP-2.25)

EPA Science Inventory

This SOP describes the method for conducting internal field audits and quality control procedures. Internal field audits will be conducted to ensure the collection of high quality data. Internal field audits will be conducted by Field Auditors (the Field QA Officer and the Field...

Statistical process control methods allow the analysis and improvement of anesthesia care.

PubMed

Fasting, Sigurd; Gisvold, Sven E

2003-10-01

Quality aspects of the anesthetic process are reflected in the rate of intraoperative adverse events. The purpose of this report is to illustrate how the quality of the anesthesia process can be analyzed using statistical process control methods, and exemplify how this analysis can be used for quality improvement. We prospectively recorded anesthesia-related data from all anesthetics for five years. The data included intraoperative adverse events, which were graded into four levels, according to severity. We selected four adverse events, representing important quality and safety aspects, for statistical process control analysis. These were: inadequate regional anesthesia, difficult emergence from general anesthesia, intubation difficulties and drug errors. We analyzed the underlying process using 'p-charts' for statistical process control. In 65,170 anesthetics we recorded adverse events in 18.3%; mostly of lesser severity. Control charts were used to define statistically the predictable normal variation in problem rate, and then used as a basis for analysis of the selected problems with the following results: Inadequate plexus anesthesia: stable process, but unacceptably high failure rate; Difficult emergence: unstable process, because of quality improvement efforts; Intubation difficulties: stable process, rate acceptable; Medication errors: methodology not suited because of low rate of errors. By applying statistical process control methods to the analysis of adverse events, we have exemplified how this allows us to determine if a process is stable, whether an intervention is required, and if quality improvement efforts have the desired effect.

Application of reiteration of Hankel singular value decomposition in quality control

NASA Astrophysics Data System (ADS)

Staniszewski, Michał; Skorupa, Agnieszka; Boguszewicz, Łukasz; Michalczuk, Agnieszka; Wereszczyński, Kamil; Wicher, Magdalena; Konopka, Marek; Sokół, Maria; Polański, Andrzej

2017-07-01

Medical centres are obliged to store past medical records, including the results of quality assurance (QA) tests of the medical equipment, which is especially useful in checking reproducibility of medical devices and procedures. Analysis of multivariate time series is an important part of quality control of NMR data. In this work we proposean anomaly detection tool based on Reiteration of Hankel Singular Value Decomposition method. The presented method was compared with external software and authors obtained comparable results.

Improved GMP-compliant multi-dose production and quality control of 6-[18F]fluoro-L-DOPA.

PubMed

Luurtsema, G; Boersma, H H; Schepers, M; de Vries, A M T; Maas, B; Zijlma, R; de Vries, E F J; Elsinga, P H

2017-01-01

6-[ 18 F]Fluoro-L-3,4-dihydroxyphenylalanine (FDOPA) is a frequently used radiopharmaceutical for detecting neuroendocrine and brain tumors and for the differential diagnosis of Parkinson's disease. To meet the demand for FDOPA, a high-yield GMP-compliant production method is required. Therefore, this study aimed to improve the FDOPA production and quality control procedures to enable distribution of the radiopharmaceutical over distances.FDOPA was prepared by electrophilic fluorination of the trimethylstannyl precursor with [ 18 F]F 2 , produced from [ 18 O] 2 via the double-shoot approach, leading to FDOPA with higher specific activity as compared to FDOPA which was synthesized, using [ 18 F]F 2 produced from 20 Ne, leading to FDOPA with a lower specific activity. The quality control of the product was performed using a validated UPLC system and compared with quality control with a conventional HPLC system. Impurities were identified using UPLC-MS. The [ 18 O] 2 double-shoot radionuclide production method yielded significantly more [ 18 F]F 2 with less carrier F 2 than the conventional method starting from 20 Ne. After adjustment of radiolabeling parameters substantially higher amounts of FDOPA with higher specific activity could be obtained. Quality control by UPLC was much faster and detected more side-products than HPLC. UPLC-MS showed that the most important side-product was FDOPA-quinone, rather than 6-hydroxydopa as suggested by the European Pharmacopoeia. The production and quality control of FDOPA were significantly improved by introducing the [ 18 O] 2 double-shoot radionuclide production method, and product analysis by UPLC, respectively. As a result, FDOPA is now routinely available for clinical practice and for distribution over distances.

A Quality Assurance Initiative for Commercial-Scale Production in High-Throughput Cryopreservation of Blue Catfish Sperm

PubMed Central

Hu, E; Liao, T. W.; Tiersch, T. R.

2013-01-01

Cryopreservation of fish sperm has been studied for decades at a laboratory (research) scale. However, high-throughput cryopreservation of fish sperm has recently been developed to enable industrial-scale production. This study treated blue catfish (Ictalurus furcatus) sperm high-throughput cryopreservation as a manufacturing production line and initiated quality assurance plan development. The main objectives were to identify: 1) the main production quality characteristics; 2) the process features for quality assurance; 3) the internal quality characteristics and their specification designs; 4) the quality control and process capability evaluation methods, and 5) the directions for further improvements and applications. The essential product quality characteristics were identified as fertility-related characteristics. Specification design which established the tolerance levels according to demand and process constraints was performed based on these quality characteristics. Meanwhile, to ensure integrity throughout the process, internal quality characteristics (characteristics at each quality control point within process) that could affect fertility-related quality characteristics were defined with specifications. Due to the process feature of 100% inspection (quality inspection of every fish), a specific calculation method, use of cumulative sum (CUSUM) control charts, was applied to monitor each quality characteristic. An index of overall process evaluation, process capacity, was analyzed based on in-control process and the designed specifications, which further integrates the quality assurance plan. With the established quality assurance plan, the process could operate stably and quality of products would be reliable. PMID:23872356

7 CFR 90.102 - Quality assurance review.

Code of Federal Regulations, 2011 CFR

2011-01-01

... INTRODUCTION Quality Assurance § 90.102 Quality assurance review. (a) Each laboratory performing tests and... review of the adequacy of quality control measures taken by the laboratory for the standardized method of...

7 CFR 90.102 - Quality assurance review.

Code of Federal Regulations, 2012 CFR

2012-01-01

... INTRODUCTION Quality Assurance § 90.102 Quality assurance review. (a) Each laboratory performing tests and... review of the adequacy of quality control measures taken by the laboratory for the standardized method of...

7 CFR 90.102 - Quality assurance review.

Code of Federal Regulations, 2013 CFR

2013-01-01

... INTRODUCTION Quality Assurance § 90.102 Quality assurance review. (a) Each laboratory performing tests and... review of the adequacy of quality control measures taken by the laboratory for the standardized method of...

7 CFR 90.102 - Quality assurance review.

Code of Federal Regulations, 2014 CFR

2014-01-01

... INTRODUCTION Quality Assurance § 90.102 Quality assurance review. (a) Each laboratory performing tests and... review of the adequacy of quality control measures taken by the laboratory for the standardized method of...

[Preparation of freeze - drying control materials of IgG antibody against Schistosoma japonicum for immunodetection kits].

PubMed

Jin, Huang; Chun-Lian, Tang; Zu-Wu, Tu; Li, Tang; Ke-Hui, Zhang; Qian, Li; Jun, Ye

2018-04-18

To prepare freeze-drying control materials of IgG antibody against Schistosoma japonicum for detection kits. The serum samples of schistosomiasis patients from endemic areas and normal people without history of schistosome infection or contact with infested water in Hubei Province were collected. All the sera were detected by the method approved by China Food and Drug Administration and selected for preparation of quality control samples. Totally twelve positive quality control materials, ten negative quality control materials, and one sensitive and one precision quality control materials were screened. According to the positive serum level, the positive degrees of quality control materials were divided into strong, medium and weak levels. The stability could be valid for one year. The freeze-drying quality control materials of IgG antibody against S. japonicum for detection kits are prepared. They are easy to use and have good stability, and therefore, they may meet the requirement of quality control for the detection of schistosomiasis diagnostics kits.

A Lean Six Sigma approach to the improvement of the selenium analysis method.

PubMed

Cloete, Bronwyn C; Bester, André

2012-11-02

Reliable results represent the pinnacle assessment of quality of an analytical laboratory, and therefore variability is considered to be a critical quality problem associated with the selenium analysis method executed at Western Cape Provincial Veterinary Laboratory (WCPVL). The elimination and control of variability is undoubtedly of significant importance because of the narrow margin of safety between toxic and deficient doses of the trace element for good animal health. A quality methodology known as Lean Six Sigma was believed to present the most feasible solution for overcoming the adverse effect of variation, through steps towards analytical process improvement. Lean Six Sigma represents a form of scientific method type, which is empirical, inductive and deductive, and systematic, which relies on data, and is fact-based. The Lean Six Sigma methodology comprises five macro-phases, namely Define, Measure, Analyse, Improve and Control (DMAIC). Both qualitative and quantitative laboratory data were collected in terms of these phases. Qualitative data were collected by using quality-tools, namely an Ishikawa diagram, a Pareto chart, Kaizen analysis and a Failure Mode Effect analysis tool. Quantitative laboratory data, based on the analytical chemistry test method, were collected through a controlled experiment. The controlled experiment entailed 13 replicated runs of the selenium test method, whereby 11 samples were repetitively analysed, whilst Certified Reference Material (CRM) was also included in 6 of the runs. Laboratory results obtained from the controlled experiment was analysed by using statistical methods, commonly associated with quality validation of chemistry procedures. Analysis of both sets of data yielded an improved selenium analysis method, believed to provide greater reliability of results, in addition to a greatly reduced cycle time and superior control features. Lean Six Sigma may therefore be regarded as a valuable tool in any laboratory, and represents both a management discipline, and a standardised approach to problem solving and process optimisation.

Ambient Monitoring Technology Information Center (AMTIC)

EPA Pesticide Factsheets

This site contains information on ambient air quality monitoring programs, monitoring methods, quality assurance and control procedures, and federal regulations related to ambient air quality monitoring.

Method of analysis at the U.S. Geological Survey California Water Science Center, Sacramento Laboratory - determination of haloacetic acid formation potential, method validation, and quality-control practices

USGS Publications Warehouse

Zazzi, Barbara C.; Crepeau, Kathryn L.; Fram, Miranda S.; Bergamaschi, Brian A.

2005-01-01

An analytical method for the determination of haloacetic acid formation potential of water samples has been developed by the U.S. Geological Survey California Water Science Center Sacramento Laboratory. The haloacetic acid formation potential is measured by dosing water samples with chlorine under specified conditions of pH, temperature, incubation time, darkness, and residual-free chlorine. The haloacetic acids formed are bromochloroacetic acid, bromodichloroacetic acid, dibromochloroacetic acid, dibromoacetic acid, dichloroacetic acid, monobromoacetic acid, monochloroacetic acid, tribromoacetic acid, and trichloroacetic acid. They are extracted, methylated, and then analyzed using a gas chromatograph equipped with an electron capture detector. Method validation experiments were performed to determine the method accuracy, precision, and detection limit for each of the compounds. Method detection limits for these nine haloacetic acids ranged from 0.11 to 0.45 microgram per liter. Quality-control practices include the use of blanks, quality-control samples, calibration verification standards, surrogate recovery, internal standard, matrix spikes, and duplicates.

An integrated bioanalytical method development and validation approach: case studies.

PubMed

Xue, Y-J; Melo, Brian; Vallejo, Martha; Zhao, Yuwen; Tang, Lina; Chen, Yuan-Shek; Keller, Karin M

2012-10-01

We proposed an integrated bioanalytical method development and validation approach: (1) method screening based on analyte's physicochemical properties and metabolism information to determine the most appropriate extraction/analysis conditions; (2) preliminary stability evaluation using both quality control and incurred samples to establish sample collection, storage and processing conditions; (3) mock validation to examine method accuracy and precision and incurred sample reproducibility; and (4) method validation to confirm the results obtained during method development. This integrated approach was applied to the determination of compound I in rat plasma and compound II in rat and dog plasma. The effectiveness of the approach was demonstrated by the superior quality of three method validations: (1) a zero run failure rate; (2) >93% of quality control results within 10% of nominal values; and (3) 99% incurred sample within 9.2% of the original values. In addition, rat and dog plasma methods for compound II were successfully applied to analyze more than 900 plasma samples obtained from Investigational New Drug (IND) toxicology studies in rats and dogs with near perfect results: (1) a zero run failure rate; (2) excellent accuracy and precision for standards and quality controls; and (3) 98% incurred samples within 15% of the original values. Copyright © 2011 John Wiley & Sons, Ltd.

Maturity method demonstration : final report.

DOT National Transportation Integrated Search

2003-07-01

The concrete maturity method is a quality control/quality assurance tool that can be used to assist contractors and transportation officials in producing cost-efficient, durable concrete structures. This report documents the findings of an investigat...

Benefits and Limitations of DNA Barcoding and Metabarcoding in Herbal Product Authentication

PubMed Central

Raclariu, Ancuta Cristina; Heinrich, Michael; Ichim, Mihael Cristin

2017-01-01

Abstract Introduction Herbal medicines play an important role globally in the health care sector and in industrialised countries they are often considered as an alternative to mono‐substance medicines. Current quality and authentication assessment methods rely mainly on morphology and analytical phytochemistry‐based methods detailed in pharmacopoeias. Herbal products however are often highly processed with numerous ingredients, and even if these analytical methods are accurate for quality control of specific lead or marker compounds, they are of limited suitability for the authentication of biological ingredients. Objective To review the benefits and limitations of DNA barcoding and metabarcoding in complementing current herbal product authentication. Method Recent literature relating to DNA based authentication of medicinal plants, herbal medicines and products are summarised to provide a basic understanding of how DNA barcoding and metabarcoding can be applied to this field. Results Different methods of quality control and authentication have varying resolution and usefulness along the value chain of these products. DNA barcoding can be used for authenticating products based on single herbal ingredients and DNA metabarcoding for assessment of species diversity in processed products, and both methods should be used in combination with appropriate hyphenated chemical methods for quality control. Conclusions DNA barcoding and metabarcoding have potential in the context of quality control of both well and poorly regulated supply systems. Standardisation of protocols for DNA barcoding and DNA sequence‐based identification are necessary before DNA‐based biological methods can be implemented as routine analytical approaches and approved by the competent authorities for use in regulated procedures. © 2017 The Authors. Phytochemical Analysis Published by John Wiley & Sons Ltd. PMID:28906059

Impact of rain gauge quality control and interpolation on streamflow simulation: an application to the Warwick catchment, Australia

NASA Astrophysics Data System (ADS)

Liu, Shulun; Li, Yuan; Pauwels, Valentijn R. N.; Walker, Jeffrey P.

2017-12-01

Rain gauges are widely used to obtain temporally continuous point rainfall records, which are then interpolated into spatially continuous data to force hydrological models. However, rainfall measurements and interpolation procedure are subject to various uncertainties, which can be reduced by applying quality control and selecting appropriate spatial interpolation approaches. Consequently, the integrated impact of rainfall quality control and interpolation on streamflow simulation has attracted increased attention but not been fully addressed. This study applies a quality control procedure to the hourly rainfall measurements obtained in the Warwick catchment in eastern Australia. The grid-based daily precipitation from the Australian Water Availability Project was used as a reference. The Pearson correlation coefficient between the daily accumulation of gauged rainfall and the reference data was used to eliminate gauges with significant quality issues. The unrealistic outliers were censored based on a comparison between gauged rainfall and the reference. Four interpolation methods, including the inverse distance weighting (IDW), nearest neighbors (NN), linear spline (LN), and ordinary Kriging (OK), were implemented. The four methods were firstly assessed through a cross-validation using the quality-controlled rainfall data. The impacts of the quality control and interpolation on streamflow simulation were then evaluated through a semi-distributed hydrological model. The results showed that the Nash–Sutcliffe model efficiency coefficient (NSE) and Bias of the streamflow simulations were significantly improved after quality control. In the cross-validation, the IDW and OK methods resulted in good interpolation rainfall, while the NN led to the worst result. In term of the impact on hydrological prediction, the IDW led to the most consistent streamflow predictions with the observations, according to the validation at five streamflow-gauged locations. The OK method performed second best according to streamflow predictions at the five gauges in the calibration period (01/01/2007–31/12/2011) and four gauges during the validation period (01/01/2012–30/06/2014). However, NN produced the worst prediction at the outlet of the catchment in the validation period, indicating a low robustness. While the IDW exhibited the best performance in the study catchment in terms of accuracy, robustness and efficiency, more general recommendations on the selection of rainfall interpolation methods need to be further explored.

Impact of rain gauge quality control and interpolation on streamflow simulation: an application to the Warwick catchment, Australia

NASA Astrophysics Data System (ADS)

Liu, Shulun; Li, Yuan; Pauwels, Valentijn R. N.; Walker, Jeffrey P.

2018-01-01

Rain gauges are widely used to obtain temporally continuous point rainfall records, which are then interpolated into spatially continuous data to force hydrological models. However, rainfall measurements and interpolation procedure are subject to various uncertainties, which can be reduced by applying quality control and selecting appropriate spatial interpolation approaches. Consequently, the integrated impact of rainfall quality control and interpolation on streamflow simulation has attracted increased attention but not been fully addressed. This study applies a quality control procedure to the hourly rainfall measurements obtained in the Warwick catchment in eastern Australia. The grid-based daily precipitation from the Australian Water Availability Project was used as a reference. The Pearson correlation coefficient between the daily accumulation of gauged rainfall and the reference data was used to eliminate gauges with significant quality issues. The unrealistic outliers were censored based on a comparison between gauged rainfall and the reference. Four interpolation methods, including the inverse distance weighting (IDW), nearest neighbors (NN), linear spline (LN), and ordinary Kriging (OK), were implemented. The four methods were firstly assessed through a cross-validation using the quality-controlled rainfall data. The impacts of the quality control and interpolation on streamflow simulation were then evaluated through a semi-distributed hydrological model. The results showed that the Nash–Sutcliffe model efficiency coefficient (NSE) and Bias of the streamflow simulations were significantly improved after quality control. In the cross-validation, the IDW and OK methods resulted in good interpolation rainfall, while the NN led to the worst result. In term of the impact on hydrological prediction, the IDW led to the most consistent streamflow predictions with the observations, according to the validation at five streamflow-gauged locations. The OK method performed second best according to streamflow predictions at the five gauges in the calibration period (01/01/2007–31/12/2011) and four gauges during the validation period (01/01/2012–30/06/2014). However, NN produced the worst prediction at the outlet of the catchment in the validation period, indicating a low robustness. While the IDW exhibited the best performance in the study catchment in terms of accuracy, robustness and efficiency, more general recommendations on the selection of rainfall interpolation methods need to be further explored.

Handling qualities of large flexible control-configured aircraft

NASA Technical Reports Server (NTRS)

Swaim, R. L.

1979-01-01

The approach to an analytical study of flexible airplane longitudinal handling qualities was to parametrically vary the natural frequencies of two symmetric elastic modes to induce mode interactions with the rigid body dynamics. Since the structure of the pilot model was unknown for such dynamic interactions, the optimal control pilot modeling method is being applied and used in conjunction with pilot rating method.

Iridium-192 Production for Cancer Treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rostelato, M.E.C.M.; Silva, C.P.G.; Rela, P.R.

2004-10-05

The purpose of this work is to settle a laboratory for Iridium -192 sources production, that is, to determine a wire activation method and to build a hot cell for the wires manipulation, quality control and packaging. The paper relates, mainly, the wire activation method and its quality control. The wire activation is carried out in our nuclear reactor, IEA- R1m.

[Application of bioassay in quality control of Chinese materia medica-taking Radix Isatidis as an example].

PubMed

Yan, Dan; Ren, Yongshen; Luo, Jiaoyang; Li, Hanbing; Feng, Xue; Xiao, Xiaohe

2010-10-01

Bioassay, which construct the characteristics consistents with Chinese medical science, is the core mode and methods for the quality control of Chinese materia medica. Taking the bioassay of Radix Isatidis as an example, the contribution, status and application of bioassay in the quality control of Chinese materia medica were introduced in this article, and two key issue (the selection of reference and measurement methods) in the process of establishing bioassay were also explained. This article expects to provide a reference for the development and improvement of the bioassay of Chinese materia medica in a practical manipulation level.

Quality status display for a vibration welding process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spicer, John Patrick; Abell, Jeffrey A.; Wincek, Michael Anthony

A method includes receiving, during a vibration welding process, a set of sensory signals from a collection of sensors positioned with respect to a work piece during formation of a weld on or within the work piece. The method also includes receiving control signals from a welding controller during the process, with the control signals causing the welding horn to vibrate at a calibrated frequency, and processing the received sensory and control signals using a host machine. Additionally, the method includes displaying a predicted weld quality status on a surface of the work piece using a status projector. The methodmore » may include identifying and display a quality status of a suspect weld. The laser projector may project a laser beam directly onto or immediately adjacent to the suspect welds, e.g., as a red, green, blue laser or a gas laser having a switched color filter.« less

[Application of traditional Chinese medicine reference standards in quality control of Chinese herbal pieces].

PubMed

Lu, Tu-Lin; Li, Jin-Ci; Yu, Jiang-Yong; Cai, Bao-Chang; Mao, Chun-Qin; Yin, Fang-Zhou

2014-01-01

Traditional Chinese medicine (TCM) reference standards plays an important role in the quality control of Chinese herbal pieces. This paper overviewed the development of TCM reference standards. By analyzing the 2010 edition of Chinese pharmacopoeia, the application of TCM reference standards in the quality control of Chinese herbal pieces was summarized, and the problems exiting in the system were put forward. In the process of improving the quality control level of Chinese herbal pieces, various kinds of advanced methods and technology should be used to research the characteristic reference standards of Chinese herbal pieces, more and more reasonable reference standards should be introduced in the quality control system of Chinese herbal pieces. This article discussed the solutions in the aspect of TCM reference standards, and future development of quality control on Chinese herbal pieces is prospected.

Role of re-screening of cervical smears in internal quality control.

PubMed Central

Baker, A; Melcher, D; Smith, R

1995-01-01

AIMS--To investigate the use of rapid re-screening as a quality control method for previously screened cervical slides; to compare this method with 10% random re-screening and clinically indicated double screening. METHODS--Between June 1990 and December 1994, 117,890 negative smears were subjected to rapid re-screening. RESULTS--This study shows that rapid re-screening detects far greater numbers of false negative cases when compared with both 10% random re-screening and clinically indicated double screening, with no additional demand on human resources. The technique also identifies variation in the performance of screening personnel as an additional benefit. CONCLUSION--Rapid re-screening is an effective method of quality control. Although less sensitive, rapid re-screening should replace 10% random re-screening and selected re-screening as greater numbers of false negative results are detected while consuming less resources. PMID:8543619

40 CFR 75.21 - Quality assurance and quality control requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., as defined in § 72.2, k=2) of plus or minus 1.0 percent (calculated combined standard uncertainty of... system according to the quality assurance and quality control procedures in appendix B of this part. (2... requirements of Method 2, 6C, 7E, or 3A in Appendices A-1, A-2 and A-4 to part 60 of this chapter (supplemented...

Development and Application of the Key Technologies for the Quality Control and Inspection of National Geographical Conditions Survey Products

NASA Astrophysics Data System (ADS)

Zhao, Y.; Zhang, L.; Ma, W.; Zhang, P.; Zhao, T.

2018-04-01

The First National Geographical Condition Survey is a predecessor task to dynamically master basic situations of the nature, ecology and human activities on the earth's surface and it is the brand-new mapping geographic information engineering. In order to ensure comprehensive, real and accurate survey results and achieve the quality management target which the qualified rate is 100 % and the yield is more than 80 %, it is necessary to carry out the quality control and result inspection for national geographical conditions survey on a national scale. To ensure that achievement quality meets quality target requirements, this paper develops the key technology method of "five-in-one" quality control that is constituted by "quality control system of national geographical condition survey, quality inspection technology system, quality evaluation system, quality inspection information management system and national linked quality control institutions" by aiming at large scale, wide coverage range, more undertaking units, more management levels, technical updating, more production process and obvious regional differences in the national geographical condition survey and combining with novel achievement manifestation, complicated dependency, more special reference data, and large data size. This project fully considering the domestic and foreign related research results and production practice experience, combined with the technology development and the needs of the production, it stipulates the inspection methods and technical requirements of each stage in the quality inspection of the geographical condition survey results, and extends the traditional inspection and acceptance technology, and solves the key technologies that are badly needed in the first national geographic survey.

QUALITY CONTROL OF PHARMACEUTICALS.

PubMed

LEVI, L; WALKER, G C; PUGSLEY, L I

1964-10-10

Quality control is an essential operation of the pharmaceutical industry. Drugs must be marketed as safe and therapeutically active formulations whose performance is consistent and predictable. New and better medicinal agents are being produced at an accelerated rate. At the same time more exacting and sophisticated analytical methods are being developed for their evaluation. Requirements governing the quality control of pharmaceuticals in accordance with the Canadian Food and Drugs Act are cited and discussed.

A novel strategy with standardized reference extract qualification and single compound quantitative evaluation for quality control of Panax notoginseng used as a functional food.

PubMed

Li, S P; Qiao, C F; Chen, Y W; Zhao, J; Cui, X M; Zhang, Q W; Liu, X M; Hu, D J

2013-10-25

Root of Panax notoginseng (Burk.) F.H. Chen (Sanqi in Chinese) is one of traditional Chinese medicines (TCMs) based functional food. Saponins are the major bioactive components. The shortage of reference compounds or chemical standards is one of the main bottlenecks for quality control of TCMs. A novel strategy, i.e. standardized reference extract based qualification and single calibrated components directly quantitative estimation of multiple analytes, was proposed to easily and effectively control the quality of natural functional foods such as Sanqi. The feasibility and credibility of this methodology were also assessed with a developed fast HPLC method. Five saponins, including ginsenoside Rg1, Re, Rb1, Rd and notoginsenoside R1 were rapidly separated using a conventional HPLC in 20 min. The quantification method was also compared with individual calibration curve method. The strategy is feasible and credible, which is easily and effectively adapted for improving the quality control of natural functional foods such as Sanqi. Copyright © 2013 Elsevier B.V. All rights reserved.

Evaluation of mailed pediatric buccal cytobrushes for use in a case-control study of birth defects.

PubMed

Gallagher, Margaret L; Sturchio, Cynthia; Smith, Ashley; Koontz, Deborah; Jenkins, Mary M; Honein, Margaret A; Rasmussen, Sonja A

2011-07-01

Buccal cell collection is a convenient DNA collection method; however, little attention has been given to the quality of DNA obtained from pediatric populations. The purpose of this study was to determine the effect of a modified cytobrush collection method on the yield and quality of infant buccal DNA collected as part of a population-based case-control study of birth defects. METHODS Cytobrushes were collected from infants, mothers, and fathers using a standard collection method in 1997 to 2003 and a modified protocol that allows air-drying of the cytobrushes after collection from 2003 to the present. Yield and quality of DNA from 1057 cytobrushes was assessed by quantitative PCR and short tandem repeat (STR) genotyping, respectively. RESULTS Air-dried cytobrushes from infants had higher median DNA yields (1300 ng) and STR completion rates (99.5%) than standard collection method cytobrushes (60 ng and 59.5%, respectively). A subset of DNA aliquots was genotyped for six single nucleotide polymorphisms (SNPs). Aliquots from both collection methods that passed the quality protocol (DNA concentration >1 ng/μl, and successful amplification of ≥1 STR) had high genotype completion rates (99-100%). The median DNA yield following whole genome amplification was more than twofold higher for air-dried than standard collection specimens (p < 0.001). CONCLUSION Yield and quality of buccal DNA collected from infants are improved by using a method that incorporates air-drying; however, DNA collected by both methods is suitable for genotyping if stringent quality control procedures are instituted. These findings may be helpful for future epidemiologic studies of birth defects and other adverse pediatric outcomes. Copyright © 2011 Wiley-Liss, Inc.

Benefits and Limitations of DNA Barcoding and Metabarcoding in Herbal Product Authentication.

PubMed

Raclariu, Ancuta Cristina; Heinrich, Michael; Ichim, Mihael Cristin; de Boer, Hugo

2018-03-01

Herbal medicines play an important role globally in the health care sector and in industrialised countries they are often considered as an alternative to mono-substance medicines. Current quality and authentication assessment methods rely mainly on morphology and analytical phytochemistry-based methods detailed in pharmacopoeias. Herbal products however are often highly processed with numerous ingredients, and even if these analytical methods are accurate for quality control of specific lead or marker compounds, they are of limited suitability for the authentication of biological ingredients. To review the benefits and limitations of DNA barcoding and metabarcoding in complementing current herbal product authentication. Recent literature relating to DNA based authentication of medicinal plants, herbal medicines and products are summarised to provide a basic understanding of how DNA barcoding and metabarcoding can be applied to this field. Different methods of quality control and authentication have varying resolution and usefulness along the value chain of these products. DNA barcoding can be used for authenticating products based on single herbal ingredients and DNA metabarcoding for assessment of species diversity in processed products, and both methods should be used in combination with appropriate hyphenated chemical methods for quality control. DNA barcoding and metabarcoding have potential in the context of quality control of both well and poorly regulated supply systems. Standardisation of protocols for DNA barcoding and DNA sequence-based identification are necessary before DNA-based biological methods can be implemented as routine analytical approaches and approved by the competent authorities for use in regulated procedures. © 2017 The Authors. Phytochemical Analysis Published by John Wiley & Sons Ltd. © 2017 The Authors. Phytochemical Analysis Published by John Wiley & Sons Ltd.

Quality evaluation of Desmodium styracifolium using high-performance liquid chromatography with photodiode array detection and electrospray ionisation tandem mass spectrometry.

PubMed

Zhou, Chan; Luo, Jian-Guang; Kong, Ling-Yi

2012-01-01

Desmodium styracifolium, with C-flavone glycosides as main pharmacological effective compounds, is a popular Chinese medicinal herb and has been used to treat urination disturbance, urolithiasis, edema and jaundice. However, few systematic methods have been reported on the quality control of this natural herb. To develop a method for control the quality of D. styracifolium by combining chromatographic fingerprints and major constituent quantification. Separations were performed on an Ultimate XB-C-18 column by gradient elution using acetonitrile and 0.1% aqueous formic acid. Analytes were identified by HPLC coupled with electrospray ionisation mass spectrometry experiments. Twenty common peaks in chromatographic fingerprints were first identified among 15 batches of D. styracifolium from various regions. On basis of this, a HPLC-PAD method was established to simultaneously quantify five major constituents, which was validated for limit of qualification, linearity and interday variation of precision and accuracy. The assay developed could be considered as a suitable quality control method of D. styracifolium. Copyright © 2011 John Wiley & Sons, Ltd.

Quality evaluation of Yin Chen Hao Tang extract based on fingerprint chromatogram and simultaneous determination of five bioactive constituents.

PubMed

Wang, Xijun; Lv, Haitao; Sun, Hui; Jiang, Xingang; Wu, Zeming; Sun, Wenjun; Wang, Ping; Liu, Lian; Bi, Kaishun

2008-01-01

A completely validated method based on HPLC coupled with photodiode array detector (HPLC-UV) was described for evaluating and controlling quality of Yin Chen Hao Tang extract (YCHTE). First, HPLC-UV fingerprint chromatogram of YCHTE was established for preliminarily elucidating amount and chromatographic trajectory of chemical constituents in YCHTE. Second, for the first time, five mainly bioactive constituents in YCHTE were simultaneously determined based on fingerprint chromatogram for furthermore controlling the quality of YCHTE quantitatively. The developed method was applied to analyze 12 batches of YCHTE samples which consisted of herbal drugs from different places of production, showed acceptable linearity, intraday (RSD <5%), interday precision (RSD <4.80%), and accuracy (RSD <2.80%). As a result, fingerprint chromatogram determined 15 representative general fingerprint peaks, and the fingerprint chromatogram resemblances are all better than 0.9996. The contents of five analytes in different batches of YCHTE samples do not indicate significant difference. So, it is concluded that the developed HPLC-UV method is a more fully validated and complete method for evaluating and controlling the quality of YCHTE.

A Quadrupole Dalton-based multi-attribute method for product characterization, process development, and quality control of therapeutic proteins.

PubMed

Xu, Weichen; Jimenez, Rod Brian; Mowery, Rachel; Luo, Haibin; Cao, Mingyan; Agarwal, Nitin; Ramos, Irina; Wang, Xiangyang; Wang, Jihong

2017-10-01

During manufacturing and storage process, therapeutic proteins are subject to various post-translational modifications (PTMs), such as isomerization, deamidation, oxidation, disulfide bond modifications and glycosylation. Certain PTMs may affect bioactivity, stability or pharmacokinetics and pharmacodynamics profile and are therefore classified as potential critical quality attributes (pCQAs). Identifying, monitoring and controlling these PTMs are usually key elements of the Quality by Design (QbD) approach. Traditionally, multiple analytical methods are utilized for these purposes, which is time consuming and costly. In recent years, multi-attribute monitoring methods have been developed in the biopharmaceutical industry. However, these methods combine high-end mass spectrometry with complicated data analysis software, which could pose difficulty when implementing in a quality control (QC) environment. Here we report a multi-attribute method (MAM) using a Quadrupole Dalton (QDa) mass detector to selectively monitor and quantitate PTMs in a therapeutic monoclonal antibody. The result output from the QDa-based MAM is straightforward and automatic. Evaluation results indicate this method provides comparable results to the traditional assays. To ensure future application in the QC environment, this method was qualified according to the International Conference on Harmonization (ICH) guideline and applied in the characterization of drug substance and stability samples. The QDa-based MAM is shown to be an extremely useful tool for product and process characterization studies that facilitates facile understanding of process impact on multiple quality attributes, while being QC friendly and cost-effective.

Use of ground penetrating radar for construction quality assurance of concrete pavement.

DOT National Transportation Integrated Search

2009-11-01

Extracting concrete cores is the most common method for measuring the thickness of concrete pavement for construction : quality control. Although this method provides a relatively accurate thickness measurement, it is destructive, labor : intensive, ...

Oromucosal film preparations: classification and characterization methods.

PubMed

Preis, Maren; Woertz, Christina; Kleinebudde, Peter; Breitkreutz, Jörg

2013-09-01

Recently, the regulatory authorities have enlarged the variety of 'oromucosal preparations' by buccal films and orodispersible films. Various film preparations have entered the market and pharmacopoeias. Due to the novelty of the official monographs, no standardized characterization methods and quality specifications are included. This review reports the methods of choice to characterize oromucosal film preparations with respect to biorelevant characterization and quality control. Commonly used dissolution tests for other dosage forms are not transferable for films in all cases. Alternatives and guidance on decision, which methods are favorable for film preparations are discussed. Furthermore, issues about requirements for film dosage forms are reflected. Oromucosal film preparations offer a wide spectrum of opportunities. There are a lot of suggestions in the literature on how to control the quality of these innovative products, but no standardized tests are available. Regulatory authorities need to define the standards and quality requirements more precisely.

GC-C-IRMS in routine doping control practice: 3 years of drug testing data, quality control and evolution of the method.

PubMed

Polet, Michael; Van Eenoo, Peter

2015-06-01

In order to detect the misuse of endogenous anabolic steroids, doping control laboratories require methods that allow differentiation between endogenous steroids and their synthetic copies. Gas chromatography combustion isotope ratio mass spectrometry (GC-C-IRMS) is capable of measuring the carbon isotope ratio of urinary steroids and this allows differentiation between both. GC-C-IRMS and its application to doping control has evolved a lot during the last decade and so have the World Anti-Doping Agency (WADA) technical documents that describe how GC-C-IRMS should be applied. Especially the WADA technical document of 2014 introduced a number of obligatory quality controls and a fixed methodology that should be used by all the doping control laboratories. This document imposed more uniform methods between the laboratories in order to decrease the interlaboratory standard deviation and acquire similar results for the analysis of the same urine samples. In this paper, 3 years of drug testing data of our GC-C-IRMS method in routine doping control practice is described, with an emphasis on the new WADA technical document and its implementation. Useful data for other doping control laboratories is presented focussing on general method setup, quality control and data collected from routine samples. The paper concentrates on how IRMS results shift or remain similar by switching to the 2014 WADA technical document and gives insight in a straightforward approach to calculate the measurement uncertainty.

Association between bibliometric parameters, reporting and methodological quality of randomised controlled trials in vascular and endovascular surgery.

PubMed

Hajibandeh, Shahab; Hajibandeh, Shahin; Antoniou, George A; Green, Patrick A; Maden, Michelle; Torella, Francesco

2017-04-01

Purpose We aimed to investigate association between bibliometric parameters, reporting and methodological quality of vascular and endovascular surgery randomised controlled trials. Methods The most recent 75 and oldest 75 randomised controlled trials published in leading journals over a 10-year period were identified. The reporting quality was analysed using the CONSORT statement, and methodological quality with the Intercollegiate Guidelines Network checklist. We used exploratory univariate and multivariable linear regression analysis to investigate associations. Findings Bibliometric parameters such as type of journal, study design reported in title, number of pages; external funding, industry sponsoring and number of citations are associated with reporting quality. Moreover, parameters such as type of journal, subject area and study design reported in title are associated with methodological quality. Conclusions The bibliometric parameters of randomised controlled trials may be independent predictors for their reporting and methodological quality. Moreover, the reporting quality of randomised controlled trials is associated with their methodological quality and vice versa.

HPTLC Fingerprint Analysis: A Quality Control for Authentication of Herbal Phytochemicals

NASA Astrophysics Data System (ADS)

Ram, Mauji; Abdin, M. Z.; Khan, M. A.; Jha, Prabhakar

Authentication and consistent quality are the basic requirement for Indian traditional medicine (TIM), Chinese traditional herbal medicine (TCHM), and their commercial products, regardless of the kind of research conducted to modernize the TIM and TCHM. The complexities of TIM and TCHM challenge the current official quality control mode, for which only a few biochemical markers were selected for identification and quantitative assay. Referring too many unknown factors existed in TIM and TCHM, it is impossible and unnecessary to pinpoint qualitatively and quantitatively every single component contained in the herbal drug. Chromatographic fingerprint is a rational option to meet the need for more effective and powerful quality assessment to TIM and TCHM. The optimized chromatographic fingerprint is not only an alternative analytical tool for authentication, but also an approach to express the various pattern of chemical ingredients distribution in the herbal drugs and preserve such "database" for further multifaced sustainable studies. Analytical separation techniques, for example, high-performance liquid chromatography (HPLC), gas chromatography (GC) and mass spectrometry (MS) were among the most popular methods of choice used for quality control of raw material and finished herbal product. Fingerprint analysis approach using high-performance thin-layer chromatography (HPTLC) has become the most potent tool for quality control of herbal medicines because of its simplicity and reliability. It can serve as a tool for identification, authentication, and quality control of herbal drugs. In this chapter, attempts are being made to expand the use of HPTLC and at the same time create interest among prospective researcher in herbal analysis. The developed method can be used as a quality control tool for rapid authentication from a wide variety of herbal samples. Some examples demonstrated the role of fingerprinting in quality control and assessment.

Quality Control Analysis of Selected Aspects of Programs Administered by the Bureau of Student Financial Assistance. Error-Prone Model Derived from 1978-1979 Quality Control Study. Data Report. [Task 3.

ERIC Educational Resources Information Center

Saavedra, Pedro; Kuchak, JoAnn

An error-prone model (EPM) to predict financial aid applicants who are likely to misreport on Basic Educational Opportunity Grant (BEOG) applications was developed, based on interviews conducted with a quality control sample of 1,791 students during 1978-1979. The model was designed to identify corrective methods appropriate for different types of…

Quality Control of Pharmaceuticals

PubMed Central

Levi, Leo; Walker, George C.; Pugsley, L. I.

1964-01-01

Quality control is an essential operation of the pharmaceutical industry. Drugs must be marketed as safe and therapeutically active formulations whose performance is consistent and predictable. New and better medicinal agents are being produced at an accelerated rate. At the same time more exacting and sophisticated analytical methods are being developed for their evaluation. Requirements governing the quality control of pharmaceuticals in accordance with the Canadian Food and Drugs Act are cited and discussed. PMID:14199105

Research note : field control of asphalt concrete paving mixtures.

DOT National Transportation Integrated Search

1995-01-01

The goal of this study was to develop information and evaluate new methods for controlling quality of the AC mixture in the mat. Specifically, this research project evaluated a gyratory compactor in the field laboratory to determine mix quality. Spec...

14 CFR 23.621 - Casting factors.

Code of Federal Regulations, 2011 CFR

2011-01-01

... either magnetic particle, penetrant or other approved equivalent non-destructive inspection method; or... percent approved non-destructive inspection. When an approved quality control procedure is established and...) of this section must be applied in addition to those necessary to establish foundry quality control...

Guidelines for Controlling Indoor Air Quality Problems Associated with Kilns, Copiers, and Welding in Schools. Technical Bulletin.

ERIC Educational Resources Information Center

Turner, Ronald W.; And Others

Guidelines for controlling indoor air quality problems associated with kilns, copiers, and welding in schools are provided in this document. Individual sections on kilns, duplicating equipment, and welding operations contain information on the following: sources of contaminants; health effects; methods of control; ventilation strategies; and…

Assessment of an intervention to train teaching hospital care providers in quality management

PubMed Central

Francois, P; Vinck, D; Labarere, J; Reverdy, T; Peyrin, J

2005-01-01

Background: Successful implementation of continuous quality improvement (CQI) programs in hospitals remains rare in all countries, making it necessary to experiment with implementation methods while considering the cultural factors of resistance to change. Objective: To assess the impact of an educational intervention on involvement of clinical department staff in the quality process. Setting: Twelve voluntary clinical departments (six experimental and six controls) in a French 2000-bed university hospital comprising 40 clinical departments. Intervention: Three day training seminar to a group of 12–20 staff members from each department. Design: Quasi-experimental post-test only design study with control group conducted 12 months after the intervention with a questionnaire completed in a face-to-face interview. Subjects: 98 trained staff and 100 untrained staff from the six experimental departments and 100 staff from the six control departments. Principal measurements: Declared knowledge of the CQI methods and participation in quality management activities. Results: 286 people (96%) were involved in the study. More of the trained staff knew the CQI methods (62.4%) than staff in the control departments (16.5%) (adjusted odds ratio (ORa) = 10.6 (95% CI 4.97 to 22.62)). More trained staff also participated in quality improvement work groups than control department staff (76.3% v 14.0%; ORa = 27.4 (95% CI 11.6 to 64.4)). In the experimental departments the untrained staff's knowledge of CQI methods and their participation in work groups did not differ from that of control department staff. Conclusions: A continuing education intervention can involve care providers in CQI. Dissemination of knowledge from trained personnel to other staff members remains limited. PMID:16076785

[Quality control of Maca (Lepidium meyenii)].

PubMed

Shu, Ji-cheng; Cui, Hang-qing; Huang, Ying-zheng; Huang, Xiao-ying; Yang, Ming

2015-12-01

To control the quality of Maca, the quality standard was established in this study. According to the methods recorded in the Appendix of Chinese Pharmacopoeia (2010 Edition), the water, extract, total ash, acid insoluble substance, and heavy metals inspections in Lepidium meyenii were carried out. N-benzyl-9Z, 12Z-octadecadienamide in L. meyenii was identified by TLC, and it was determined by HPLC. The results showed that the N-benzyl-9Z, 12Z-octadecadienamide identification of TLC was a strong mark and specificity. In content determination experiment, the linearity of N-benzyl-9Z, 12Z-octadecadienamide was in the range of 0.01-2 microg (r = 0.9998), and the average recovery (n=9) was 99.27% (RSD 2.0%). The methods were simple, accurate, with good reproducibility. It is suitable for quality control L. meyenii.

[Development of whole process quality control and management system of traditional Chinese medicine decoction pieces based on traditional Chinese medicine quality tree].

PubMed

Yu, Wen-Kang; Dong, Ling; Pei, Wen-Xuan; Sun, Zhi-Rong; Dai, Jun-Dong; Wang, Yun

2017-12-01

The whole process quality control and management of traditional Chinese medicine (TCM) decoction pieces is a system engineering, involving the base environment, seeds and seedlings, harvesting, processing and other multiple steps, so the accurate identification of factors in TCM production process that may induce the quality risk, as well as reasonable quality control measures are very important. At present, the concept of quality risk is mainly concentrated in the aspects of management and regulations, etc. There is no comprehensive analysis on possible risks in the quality control process of TCM decoction pieces, or analysis summary of effective quality control schemes. A whole process quality control and management system for TCM decoction pieces based on TCM quality tree was proposed in this study. This system effectively combined the process analysis method of TCM quality tree with the quality risk management, and can help managers to make real-time decisions while realizing the whole process quality control of TCM. By providing personalized web interface, this system can realize user-oriented information feedback, and was convenient for users to predict, evaluate and control the quality of TCM. In the application process, the whole process quality control and management system of the TCM decoction pieces can identify the related quality factors such as base environment, cultivation and pieces processing, extend and modify the existing scientific workflow according to their own production conditions, and provide different enterprises with their own quality systems, to achieve the personalized service. As a new quality management model, this paper can provide reference for improving the quality of Chinese medicine production and quality standardization. Copyright© by the Chinese Pharmaceutical Association.

Knowledge acquisition for a simple expert controller

NASA Technical Reports Server (NTRS)

Bieker, B.

1987-01-01

A method is presented for process control which has the properties of being incremental, cyclic and top-down. It is described on the basis of the development of an expert controller for a simple, but nonlinear control route. A quality comparison between expert controller and process operator shows the ability of the method for knowledge acquisition.

Quality Control Circles: A Vehicle for Just-in-Time Implementation.

ERIC Educational Resources Information Center

Sepehri, Mehran

1985-01-01

Explains just-in-time (JIT) material flow and production, a method of production designed to eliminate waste. Discusses why quality control circles work so well with a JIT system, and describes how several companies have made JIT work for them. (CT)

The World Optical Depth Research and Calibration Center (WORCC) quality assurance and quality control of GAW-PFR AOD measurements

NASA Astrophysics Data System (ADS)

Kazadzis, Stelios; Kouremeti, Natalia; Nyeki, Stephan; Gröbner, Julian; Wehrli, Christoph

2018-02-01

The World Optical Depth Research Calibration Center (WORCC) is a section within the World Radiation Center at Physikalisches-Meteorologisches Observatorium (PMOD/WRC), Davos, Switzerland, established after the recommendations of the World Meteorological Organization for calibration of aerosol optical depth (AOD)-related Sun photometers. WORCC is mandated to develop new methods for instrument calibration, to initiate homogenization activities among different AOD networks and to run a network (GAW-PFR) of Sun photometers. In this work we describe the calibration hierarchy and methods used under WORCC and the basic procedures, tests and processing techniques in order to ensure the quality assurance and quality control of the AOD-retrieved data.

RELATIONSHIP OF ASSESS SELF-ESTEEM AND LOCUS OF CONTROL WITH QUALITY OF LIFE DURING TREATMENT STAGES IN PATIENTS REFERRING TO DRUG ADDICTION REHABILITATION CENTERS

PubMed Central

Heidari, Mohammad; Ghodusi, Mansureh

2016-01-01

Objective: Thus, the present research was carried out aimed at determining the relationship between self-esteem and locus of control and quality of life during treatment stages in the patients referring to drug addiction rehabilitation centers of Borujen city, Iran. Methods: The current study was a sectional research of descriptive correlation type. The research sample was 150 individuals of patients referring to addiction rehabilitation centers of Borujen city. For data gathering, Rosenberg Self-esteem Scale, Rotter’s Locus of Control Scale, and SF36 Quality of Life Questionnaire were used. Following collection of questionnaires, the data were analyzed using SPSS/16 software. Results: According to the results, in the 12th day of treatment, 96 patients exhibited moderate self-esteem, 102 patients had internal locus of control, and the score of their overall quality of life was 40.43±12.71. Furthermore, Pearson’s correlation coefficient indicated that a significant and positive relationship was observed between locus of control and quality of life during different treatment stages. Conclusion: It seems that quality of life improves during addiction treatment stages due to improvement of personality traits including locus of control and self-esteem. Therefore, consultation methods as a very crucial priority in addiction rehabilitation centers shall be taken into account by the health sector authorities and managers and can play an essential role in enhancing quality of life. PMID:27698598

A real time quality control application for animal production by image processing.

PubMed

Sungur, Cemil; Özkan, Halil

2015-11-01

Standards of hygiene and health are of major importance in food production, and quality control has become obligatory in this field. Thanks to rapidly developing technologies, it is now possible for automatic and safe quality control of food production. For this purpose, image-processing-based quality control systems used in industrial applications are being employed to analyze the quality of food products. In this study, quality control of chicken (Gallus domesticus) eggs was achieved using a real time image-processing technique. In order to execute the quality control processes, a conveying mechanism was used. Eggs passing on a conveyor belt were continuously photographed in real time by cameras located above the belt. The images obtained were processed by various methods and techniques. Using digital instrumentation, the volume of the eggs was measured, broken/cracked eggs were separated and dirty eggs were determined. In accordance with international standards for classifying the quality of eggs, the class of separated eggs was determined through a fuzzy implication model. According to tests carried out on thousands of eggs, a quality control process with an accuracy of 98% was possible. © 2014 Society of Chemical Industry.

24 CFR 200.935 - Administrator qualifications and procedures for HUD building products certification programs.

Code of Federal Regulations, 2011 CFR

2011-04-01

... guidelines in any quality assurance review: (1) ASQC Q9000-1-1994 Quality Management and Quality Assurance... Systems—Model for Quality Assurance in Final Inspection and Test; (5) ASQC Q9004-1-1994 Quality Management... in interpreting testing standards, test methods, evaluating test reports and quality control programs...

Improved statistical method for temperature and salinity quality control

NASA Astrophysics Data System (ADS)

Gourrion, Jérôme; Szekely, Tanguy

2017-04-01

Climate research and Ocean monitoring benefit from the continuous development of global in-situ hydrographic networks in the last decades. Apart from the increasing volume of observations available on a large range of temporal and spatial scales, a critical aspect concerns the ability to constantly improve the quality of the datasets. In the context of the Coriolis Dataset for ReAnalysis (CORA) version 4.2, a new quality control method based on a local comparison to historical extreme values ever observed is developed, implemented and validated. Temperature, salinity and potential density validity intervals are directly estimated from minimum and maximum values from an historical reference dataset, rather than from traditional mean and standard deviation estimates. Such an approach avoids strong statistical assumptions on the data distributions such as unimodality, absence of skewness and spatially homogeneous kurtosis. As a new feature, it also allows addressing simultaneously the two main objectives of an automatic quality control strategy, i.e. maximizing the number of good detections while minimizing the number of false alarms. The reference dataset is presently built from the fusion of 1) all ARGO profiles up to late 2015, 2) 3 historical CTD datasets and 3) the Sea Mammals CTD profiles from the MEOP database. All datasets are extensively and manually quality controlled. In this communication, the latest method validation results are also presented. The method has already been implemented in the latest version of the delayed-time CMEMS in-situ dataset and will be deployed soon in the equivalent near-real time products.

Improved Statistical Method For Hydrographic Climatic Records Quality Control

NASA Astrophysics Data System (ADS)

Gourrion, J.; Szekely, T.

2016-02-01

Climate research benefits from the continuous development of global in-situ hydrographic networks in the last decades. Apart from the increasing volume of observations available on a large range of temporal and spatial scales, a critical aspect concerns the ability to constantly improve the quality of the datasets. In the context of the Coriolis Dataset for ReAnalysis (CORA) version 4.2, a new quality control method based on a local comparison to historical extreme values ever observed is developed, implemented and validated. Temperature, salinity and potential density validity intervals are directly estimated from minimum and maximum values from an historical reference dataset, rather than from traditional mean and standard deviation estimates. Such an approach avoids strong statistical assumptions on the data distributions such as unimodality, absence of skewness and spatially homogeneous kurtosis. As a new feature, it also allows addressing simultaneously the two main objectives of a quality control strategy, i.e. maximizing the number of good detections while minimizing the number of false alarms. The reference dataset is presently built from the fusion of 1) all ARGO profiles up to early 2014, 2) 3 historical CTD datasets and 3) the Sea Mammals CTD profiles from the MEOP database. All datasets are extensively and manually quality controlled. In this communication, the latest method validation results are also presented. The method has been implemented in the latest version of the CORA dataset and will benefit to the next version of the Copernicus CMEMS dataset.

Quality control process improvement of flexible printed circuit board by FMEA

NASA Astrophysics Data System (ADS)

Krasaephol, Siwaporn; Chutima, Parames

2018-02-01

This research focuses on the quality control process improvement of Flexible Printed Circuit Board (FPCB), centred around model 7-Flex, by using Failure Mode and Effect Analysis (FMEA) method to decrease proportion of defective finished goods that are found at the final inspection process. Due to a number of defective units that were found at the final inspection process, high scraps may be escaped to customers. The problem comes from poor quality control process which is not efficient enough to filter defective products from in-process because there is no In-Process Quality Control (IPQC) or sampling inspection in the process. Therefore, the quality control process has to be improved by setting inspection gates and IPCQs at critical processes in order to filter the defective products. The critical processes are analysed by the FMEA method. IPQC is used for detecting defective products and reducing chances of defective finished goods escaped to the customers. Reducing proportion of defective finished goods also decreases scrap cost because finished goods incur higher scrap cost than work in-process. Moreover, defective products that are found during process can reflect the abnormal processes; therefore, engineers and operators should timely solve the problems. Improved quality control was implemented for 7-Flex production lines from July 2017 to September 2017. The result shows decreasing of the average proportion of defective finished goods and the average of Customer Manufacturers Lot Reject Rate (%LRR of CMs) equal to 4.5% and 4.1% respectively. Furthermore, cost saving of this quality control process equals to 100K Baht.

Quality evaluation and control of end cap welds in PHWR fuel elements by ultrasonic examination

NASA Astrophysics Data System (ADS)

Choi, M. S.; Yang, M. S.

1991-02-01

The current quality control procedure of nuclear fuel end cap weld is mainly dependent on the destructive metallographic examination. A nondestructive examination technique, i.e., ultrasonic examination, has been developed to identify and evaluate weld discontinuities. A few interesting results of the weld quality evaluation by applying the developed ultrasonic examination technique to PHWR fuel welds are presented. In addition, the feasibility of the weld quality control by the ultrasonic examination is discussed. This study shows that the ultrasonic examination is effective and reliable method for detecting abnormal weld contours and weld discontinuities such as micro-fissure, crack, upset split and expulsion, and can be used as a quality control tool for the end cap welding process.

GenePRIMP: A software quality control tool

ScienceCinema

Amrita Pati

2017-12-09

Amrita Pati of the DOE Joint Genome Institute's Genome Biology group describes the software tool GenePRIMP and how it fits into the quality control pipeline for microbial genomics. Further details regarding GenePRIMP appear in a paper published online May 2, 2010 in Nature Methods.

Sap flow sensors: construction, quality control and comparison.

PubMed

Davis, Tyler W; Kuo, Chen-Min; Liang, Xu; Yu, Pao-Shan

2012-01-01

This work provides a design for two types of sensors, based on the thermal dissipation and heat ratio methods of sap flow calculation, for moderate to large scale deployments for the purpose of monitoring tree transpiration. These designs include a procedure for making these sensors, a quality control method for the final products, and a complete list of components with vendors and pricing information. Both sensor designs were field tested alongside a commercial sap flow sensor to assess their performance and show the importance for quality controlling the sensor outputs. Results show that for roughly 2% of the cost of commercial sensors, self-made sap flow sensors can provide acceptable estimates of the sap flow measurements compared to the commercial sensors.

Patient perspectives of telemedicine quality

PubMed Central

LeRouge, Cynthia M; Garfield, Monica J; Hevner, Alan R

2015-01-01

Background The purpose of this study was to explore the quality attributes required for effective telemedicine encounters from the perspective of the patient. Methods We used a multi-method (direct observation, focus groups, survey) field study to collect data from patients who had experienced telemedicine encounters. Multi-perspectives (researcher and provider) were used to interpret a rich set of data from both a research and practice perspective. Results The result of this field study is a taxonomy of quality attributes for telemedicine service encounters that prioritizes the attributes from the patient perspective. We identify opportunities to control the level of quality for each attribute (ie, who is responsible for control of each attribute and when control can be exerted in relation to the encounter process). This analysis reveals that many quality attributes are in the hands of various stakeholders, and all attributes can be addressed proactively to some degree before the encounter begins. Conclusion Identification of the quality attributes important to a telemedicine encounter from a patient perspective enables one to better design telemedicine encounters. This preliminary work not only identifies such attributes, but also ascertains who is best able to address quality issues prior to an encounter. For practitioners, explicit representation of the quality attributes of technology-based systems and processes and insight on controlling key attributes are essential to implementation, utilization, management, and common understanding. PMID:25565781

Quality evaluation of Hypericum ascyron extract by two-dimensional high-performance liquid chromatography coupled with the colorimetric 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide method.

PubMed

Li, Xiu-Mei; Luo, Xue-Gang; Zhang, Chao-Zheng; Wang, Nan; Zhang, Tong-Cun

2015-02-01

In this paper, a heart-cutting two-dimensional high-performance liquid chromatography coupled with the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) method was established for controlling the quality of different batches of Hypericum ascyron extract for the first time. In comparison with the common one-dimensional fingerprint, the second-dimensional fingerprint compiled additional spectral data and was hence more informative. The quality of H. ascyron extract was further evaluated by similarity measures and the same results were achieved, the correlation coefficients of the similarity of ten batches of H. ascyron extract were ＞0.99. Furthermore, we also evaluated the quality of the ten batches of H. ascyron extract by antibacterial activity. The result demonstrated that the quality of the ten batches of H. ascyron extract was not significantly different by MTT. Finally, we demonstrated that the second-dimensional fingerprint coupled with the MTT method was a more powerful tool to characterize the quality of samples of batch to batch. Therefore the proposed method could be used to comprehensively conduct the quality control of traditional Chinese medicines. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Application of fingerprint chromatogram in quality control of Shen-Mai injection].

PubMed

Shi, Xian-zhe; Yang, Jun; Zhao, Chun-xia; Xiong, Jian-hui; Xu, Guo-wang

2002-07-01

The theory and practice of traditional Chinese medicine require some comprehensive methods to assess quality of the Chinese herbal medication. Fingerprint chromatogram is one of the feasible approaches to evaluate the quality of Chinese herbal medication. So the fingerprint chromatogram of Shen-Mai injection was established by using reversed-phase high performance liquid chromatography. The chromatographic conditions were as follows: a Hypersil C18 column was used; the mobile phase was composed of water (A) and acetontrile (B) with linear gradient elution (0-50 min, 5%-95% B, volume fraction); the flow rate was 1.0 mL/min and the UV absorbance detection was set at 202 nm. The peak-area ratios of twenty-three fingerprint peaks and internal standard (diphenyl) were taken as the criteria for quality control. The quality differences in various batches and various manufacturers of Shen-Mai injections were investigated by projection discriminance based on principal component analysis. The results show the method developed is convenient, reliable and applicable for the quality control analysis of Shen-Mai injection.

Statistical Process Control Charts for Measuring and Monitoring Temporal Consistency of Ratings

ERIC Educational Resources Information Center

Omar, M. Hafidz

2010-01-01

Methods of statistical process control were briefly investigated in the field of educational measurement as early as 1999. However, only the use of a cumulative sum chart was explored. In this article other methods of statistical quality control are introduced and explored. In particular, methods in the form of Shewhart mean and standard deviation…

Quality control of fireproof coatings for reinforced concrete structures

NASA Astrophysics Data System (ADS)

Gravit, Marina; Dmitriev, Ivan; Ishkov, Alexander

2017-10-01

The article analyzes methods of quality inspection of fireproof coatings (work flow, measuring, laboratory, etc.). In modern construction there is a problem of lack of distinct monitoring for the fire protection testing. There is a description of this testing for reinforced concrete structures. The article shows the results of calculation quality control of hatches as an example of fireproof coating for reinforced concrete structures.

The PEDALS Stationary Cycling Intervention and Health-Related Quality of Life in Children with Cerebral Palsy: A Randomized Controlled Trial

ERIC Educational Resources Information Center

DeMuth, Sharon K.; Knutson, Loretta M.; Fowler, Eileen G.

2012-01-01

Aim: The aim of this study was to assess health-related quality of life (HRQOL) following a stationary cycling intervention in children with cerebral palsy (CP). Method: This was a phase I multisite randomized controlled trial with single blinding. HRQOL was evaluated using the Pediatric Quality of Life Inventory SF15 (PedsQL; children) and…

Report of the international workshop on quality control of monthly climate data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-12-31

The National Climatic Data Center (NCDC), the US Department of Energy`s Carbon Dioxide Information Analysis Center, and the World Meteorological Organization (WMO) cosponsored an international quality control workshop for monthly climate data, October 5--6, 1993, at NCDC. About 40 scientists from around the world participated. The purpose of the meeting was to discuss and compare various quality control methods and to draft recommendations concerning the most successful systems. The near-term goal to improve quality control of CLIMAT messages for the NCDC/WMO publication Monthly Climatic Data for the World was sucessfully met. An electronic bulletin board was established to post errorsmore » and corrections. Improved communications among Global Telecommunication System hubs will be implemented. Advanced quality control algorithms were discussed and improvements were suggested. Further data exchanges were arranged.« less

Parametric synthesis of a robust controller on a base of mathematical programming method

NASA Astrophysics Data System (ADS)

Khozhaev, I. V.; Gayvoronskiy, S. A.; Ezangina, T. A.

2018-05-01

Considered paper is dedicated to deriving sufficient conditions, linking root indices of robust control quality with coefficients of interval characteristic polynomial, on the base of mathematical programming method. On the base of these conditions, a method of PI- and PID-controllers, providing aperiodic transient process with acceptable stability degree and, subsequently, acceptable setting time, synthesis was developed. The method was applied to a problem of synthesizing a controller for a depth control system of an unmanned underwater vehicle.

Making Quality Sense: A Guide to Quality, Tools and Techniques, Awards and the Thinking Behind Them.

ERIC Educational Resources Information Center

Owen, Jane

This document is intended to guide further education colleges and work-based learning providers through some of the commonly used tools, techniques, and theories of quality management. The following are among the topics discussed: (1) various ways of defining quality; methods used by organizations to achieve quality (quality control, quality…

Quality control of colonoscopy procedures: a prospective validated method for the evaluation of professional practices applicable to all endoscopic units.

PubMed

Coriat, R; Pommaret, E; Chryssostalis, A; Viennot, S; Gaudric, M; Brezault, C; Lamarque, D; Roche, H; Verdier, D; Parlier, D; Prat, F; Chaussade, S

2009-02-01

To produce valid information, an evaluation of professional practices has to assess the quality of all practices before, during and after the procedure under study. Several auditing techniques have been proposed for colonoscopy. The purpose of this work is to describe a straightforward original validated method for the prospective evaluation of professional practices in the field of colonoscopy applicable in all endoscopy units without increasing the staff work load. Pertinent quality-control criteria (14 items) were identified by the endoscopists at the Cochin Hospital and were compatible with: findings in the available literature; guidelines proposed by the Superior Health Authority; and application in any endoscopy unit. Prospective routine data were collected and the methodology validated by evaluating 50 colonoscopies every quarter for one year. The relevance of the criteria was assessed using data collected during four separate periods. The standard checklist was complete for 57% of the colonoscopy procedures. The colonoscopy procedure was appropriate according to national guidelines in 94% of cases. These observations were particularly noteworthy: the quality of the colonic preparation was insufficient for 9% of the procedures; complete colonoscopy was achieved for 93% of patients; and 0.38 adenomas and 0.045 carcinomas were identified per colonoscopy. This simple and reproducible method can be used for valid quality-control audits in all endoscopy units. In France, unit-wide application of this method enables endoscopists to validate 100 of the 250 points required for continuous medical training. This is a quality-control tool that can be applied annually, using a random month to evaluate any changes in routine practices.

The importance of quality control in validating concentrations ...

EPA Pesticide Factsheets

A national-scale survey of 247 contaminants of emerging concern (CECs), including organic and inorganic chemical compounds, and microbial contaminants, was conducted in source and treated drinking water samples from 25 treatment plants across the United States. Multiple methods were used to determine these CECs, including six analytical methods to measure 174 pharmaceuticals, personal care products, and pesticides. A three-component quality assurance/quality control (QA/QC) program was designed for the subset of 174 CECs which allowed us to assess and compare performances of the methods used. The three components included: 1) a common field QA/QC protocol and sample design, 2) individual investigator-developed method-specific QA/QC protocols, and 3) a suite of 46 method comparison analytes that were determined in two or more analytical methods. Overall method performance for the 174 organic chemical CECs was assessed by comparing spiked recoveries in reagent, source, and treated water over a two-year period. In addition to the 247 CECs reported in the larger drinking water study, another 48 pharmaceutical compounds measured did not consistently meet predetermined quality standards. Methodologies that did not seem suitable for these analytes are overviewed. The need to exclude analytes based on method performance demonstrates the importance of additional QA/QC protocols. This paper compares the method performance of six analytical methods used to measure 174 emer

Random Forest Application for NEXRAD Radar Data Quality Control

NASA Astrophysics Data System (ADS)

Keem, M.; Seo, B. C.; Krajewski, W. F.

2017-12-01

Identification and elimination of non-meteorological radar echoes (e.g., returns from ground, wind turbines, and biological targets) are the basic data quality control steps before radar data use in quantitative applications (e.g., precipitation estimation). Although WSR-88Ds' recent upgrade to dual-polarization has enhanced this quality control and echo classification, there are still challenges to detect some non-meteorological echoes that show precipitation-like characteristics (e.g., wind turbine or anomalous propagation clutter embedded in rain). With this in mind, a new quality control method using Random Forest is proposed in this study. This classification algorithm is known to produce reliable results with less uncertainty. The method introduces randomness into sampling and feature selections and integrates consequent multiple decision trees. The multidimensional structure of the trees can characterize the statistical interactions of involved multiple features in complex situations. The authors explore the performance of Random Forest method for NEXRAD radar data quality control. Training datasets are selected using several clear cases of precipitation and non-precipitation (but with some non-meteorological echoes). The model is structured using available candidate features (from the NEXRAD data) such as horizontal reflectivity, differential reflectivity, differential phase shift, copolar correlation coefficient, and their horizontal textures (e.g., local standard deviation). The influence of each feature on classification results are quantified by variable importance measures that are automatically estimated by the Random Forest algorithm. Therefore, the number and types of features in the final forest can be examined based on the classification accuracy. The authors demonstrate the capability of the proposed approach using several cases ranging from distinct to complex rain/no-rain events and compare the performance with the existing algorithms (e.g., MRMS). They also discuss operational feasibility based on the observed strength and weakness of the method.

The effect of a novel photodynamic activation method mediated by curcumin on oyster shelf life and quality.

PubMed

Liu, Fang; Li, Zhaojie; Cao, Binbin; Wu, Juan; Wang, Yuming; Xue, Yong; Xu, Jie; Xue, Changhu; Tang, Qing Juan

2016-09-01

In this paper, the effect of photodynamic method mediated by curcumin (PDT) on the shelf life and quality of pacific oysters during storage at 5±1°C were analyzed. In our previous study we investigated the optimal treatment conditions of photodynamic method mediated by curcumin to sterilization were 10uM photosensitizer concentration and 5.4J/cm 2 light energy density. Under these conditions, the effect of a novel photodynamic activation method mediated by curcumin on oyster shelf life and quality was researched. The total bacterial counts, TVB-N content and sensory analysis were used to evaluate the effects on oyster shelf life. The oyster shelf life was prolonged from 8days to 12days after photodynamic treatment and the oysters in the treatment group displayed notable odor retention, produced fewer odor corrupting substances when the control group oysters reached the end of their shelf life (day 8). Texture, free amino acid contents and fatty acid levels were applied to estimate the quality of the treated oysters. The texture had no significant change after treated with PDT. At the end of oyster shelf life, compared PDT group (PDT) with control group (control), total free amino acid contents (control: 234.30mg/100g, PDT: 813.02mg/100g) was higher and free fatty acid levels (control: 0.071mEq/L, PDT: 0.0455mEq/L) displayed lower in PDT group. This indicated that the treated oysters oxidized minimally, decayed slowly, decomposed fewer nutrients and had lower metabolic levels of spoilage microorganisms. PDT has a positive effect on prolonging oyster shelf life and its quality. Copyright © 2016 Elsevier Ltd. All rights reserved.

A Novel Hybrid Error Criterion-Based Active Control Method for on-Line Milling Vibration Suppression with Piezoelectric Actuators and Sensors

PubMed Central

Zhang, Xingwu; Wang, Chenxi; Gao, Robert X.; Yan, Ruqiang; Chen, Xuefeng; Wang, Shibin

2016-01-01

Milling vibration is one of the most serious factors affecting machining quality and precision. In this paper a novel hybrid error criterion-based frequency-domain LMS active control method is constructed and used for vibration suppression of milling processes by piezoelectric actuators and sensors, in which only one Fast Fourier Transform (FFT) is used and no Inverse Fast Fourier Transform (IFFT) is involved. The correction formulas are derived by a steepest descent procedure and the control parameters are analyzed and optimized. Then, a novel hybrid error criterion is constructed to improve the adaptability, reliability and anti-interference ability of the constructed control algorithm. Finally, based on piezoelectric actuators and acceleration sensors, a simulation of a spindle and a milling process experiment are presented to verify the proposed method. Besides, a protection program is added in the control flow to enhance the reliability of the control method in applications. The simulation and experiment results indicate that the proposed method is an effective and reliable way for on-line vibration suppression, and the machining quality can be obviously improved. PMID:26751448

Methods of Statistical Control for Groundwater Quality Indicators

NASA Astrophysics Data System (ADS)

Yankovich, E.; Nevidimova, O.; Yankovich, K.

2016-06-01

The article describes the results of conducted groundwater quality control. Controlled quality indicators included the following microelements - barium, manganese, iron, mercury, iodine, chromium, strontium, etc. Quality control charts - X-bar chart and R chart - were built. For the upper and the lower threshold limits, maximum permissible concentration of components in water and the lower limit of their biologically significant concentration, respectively, were selected. The charts analysis has shown that the levels of microelements content in water at the area of study are stable. Most elements in the underground water are contained in concentrations, significant for human organisms consuming the water. For example, such elements as Ba, Mn, Fe have concentrations that exceed maximum permissible levels for drinking water.

Effect of chemical and mechanical weed control on cassava yield, soil quality and erosion under cassava cropping system

NASA Astrophysics Data System (ADS)

Islami, Titiek; Wisnubroto, Erwin; Utomo, Wani

2016-04-01

Three years field experiments were conducted to study the effect of chemical and mechanical weed control on soil quality and erosion under cassava cropping system. The experiment were conducted at University Brawijaya field experimental station, Jatikerto, Malang, Indonesia. The experiments were carried out from 2011 - 2014. The treatments consist of three cropping system (cassava mono culture; cassava + maize intercropping and cassava + peanut intercropping), and two weed control method (chemical and mechanical methods). The experimental result showed that the yield of cassava first year and second year did not influenced by weed control method and cropping system. However, the third year yield of cassava was influence by weed control method and cropping system. The cassava yield planted in cassava + maize intercropping system with chemical weed control methods was only 24 t/ha, which lower compared to other treatments, even with that of the same cropping system used mechanical weed control. The highest cassava yield in third year was obtained by cassava + peanuts cropping system with mechanical weed control method. After three years experiment, the soil of cassava monoculture system with chemical weed control method possessed the lowest soil organic matter, and soil aggregate stability. During three years of cropping soil erosion in chemical weed control method, especially on cassava monoculture, was higher compared to mechanical weed control method. The soil loss from chemical control method were 40 t/ha, 44 t/ha and 54 t/ha for the first, second and third year crop. The soil loss from mechanical weed control method for the same years was: 36 t/ha, 36 t/ha and 38 t/ha. Key words: herbicide, intercropping, soil organic matter, aggregate stability.

[Quality process control system of Chinese medicine preparation based on "holistic view"].

PubMed

Wang, Ya-Qi; Jiao, Jiao-Jiao; Wu, Zhen-Feng; Zheng, Qin; Yang, Ming

2018-01-01

"High quality, safety and effectiveness" are the primary principles for the pharmaceutical research and development process in China. The quality of products relies not only on the inspection method, but also on the design and development, process control and standardized management. The quality depends on the process control level. In this paper, the history and current development of quality control of traditional Chinese medicine (TCM) preparations are reviewed systematically. Based on the development model of international drug quality control and the misunderstanding of quality control of TCM preparations, the reasons for impacting the homogeneity of TCM preparations are analyzed and summarized. According to TCM characteristics, efforts were made to control the diversity of TCM, make "unstable" TCM into "stable" Chinese patent medicines, put forward the concepts of "holistic view" and "QbD (quality by design)", so as to create the "holistic, modular, data, standardized" model as the core of TCM preparation quality process control model. Scientific studies shall conform to the actual production of TCM preparations, and be conducive to supporting advanced equipment and technology upgrade, thoroughly applying the scientific research achievements in Chinese patent medicines, and promoting the cluster application and transformation application of TCM pharmaceutical technology, so as to improve the quality and effectiveness of the TCM industry and realize the green development. Copyright© by the Chinese Pharmaceutical Association.

Interlaboratory Study of Quality Control Isolates for a Broth Microdilution Method (Modified CLSI M38-A) for Testing Susceptibilities of Dermatophytes to Antifungals▿

PubMed Central

Ghannoum, M. A.; Arthington-Skaggs, B.; Chaturvedi, V.; Espinel-Ingroff, A.; Pfaller, M. A.; Rennie, R.; Rinaldi, M. G.; Walsh, T. J.

2006-01-01

The Clinical and Laboratory Standards Institute (CLSI; formerly National Committee for Clinical Laboratory Standards, or NCCLS) M38-A standard for the susceptibility testing of filamentous fungi does not specifically address the testing of dermatophytes. In 2003, a multicenter study investigated the reproducibility of the microdilution method developed at the Center for Medical Mycology, Cleveland, Ohio, for testing the susceptibility of dermatophytes. Data from that study supported the introduction of this method for testing dermatophytes in the future version of the CLSI M38-A standard. In order for the method to be accepted by CLSI, appropriate quality control isolates needed to be identified. To that end, an interlaboratory study, involving the original six laboratories plus two additional sites, was conducted to evaluate potential candidates for quality control isolates. These candidate strains included five Trichophyton rubrum strains known to have elevated MICs to terbinafine and five Trichophyton mentagrophytes strains. Antifungal agents tested included ciclopirox, fluconazole, griseofulvin, itraconazole, posaconazole, terbinafine, and voriconazole. Based on the data generated, two quality control isolates, one T. rubrum isolate and one T. mentagrophytes isolate, were identified and submitted to the American Type Culture Collection (ATCC) for inclusion as reference strains. Ranges encompassing 95.2 to 97.9% of all data points for all seven drugs were established. PMID:17050812

Factors of quality of financial report of local government in Indonesia

NASA Astrophysics Data System (ADS)

Muda, Iskandar; Haris Harahap, Abdul; Erlina; Ginting, Syafruddin; Maksum, Azhar; Abubakar, Erwin

2018-03-01

The purpose of this research is to find out whether the Accounting Information System and Internal Control in Local Revenue Office to the affect the Quality of Financial Report of Local Government. The sampling was conducted by using simple random sampling method in which the sample was determined without considering strata. The data research was conducted by distributing the questionnaires. The results showed that the degree of Accounting Information System and Internal Control simultaneously affect the Quality of Financial Report of Local Government. However, partially, Partially, accounting information system influence to the quality of financial report of local government and the internal control does not affect the quality of financial report.

National Survey on Internal Quality Control for HbA(1c) Analytical Instruments in 331 Hospital Laboratories of China.

PubMed

Zeng, Rong; Wang, Wei; Zhao, Haijian; Fei, Yang; Wang, Zhiguo

2015-01-01

The narrow gap of HbA1 value of mass fraction between "normal" (< 6.0%) and "diabetes" (≥ 6.5%) necessitates tight control of inter-assay standardization, assay precision, and trueness. This survey was initiated to obtain knowledge of the current situation of internal quality control (IQC) practice for HbA(1c) in China and find out the most appropriate quality specifications. Data of IQC for HbA(1c) in 331 institutions participating in the national proficiency testing (PT) programs in China were evaluated using four levels of quality specifications, and the percentages of laboratories meeting the quality requirement were calculated to find out the most appropriate quality specifications for control materials of HbA(1c) in China. The IQC data varied vastly among 331 clinical laboratories in China. The measurement of control materials covered a wide range from 4.52% to 12.24% (inter-quartile range) and there were significant differences among the CVs of different methods, including LPLC, CE-HPLC, AC-HPLC, immunoturbidimetry, and others. Among the four main methods, CE-HPLC and AC-HPLC achieved a better precision. As we can see, the performance of laboratories for HbA(1c) has yet to be improved. Clinical laboratories in China should improve their performance with a stricter imprecision criteria.

Microbiological quality of spinach irrigated with reclaimed wastewater and roof-harvest water

USDA-ARS?s Scientific Manuscript database

Aims: The effect of reclaimed wastewater (RCW) and roof-harvest rainwater (RHW) on microbiological quality of irrigated spinach was investigated. Methods and Results: Spinach grown in controlled environment chamber was irrigated by RCW, RHW, or creek water (CW; control water) for four weeks, and th...

Quality control ranges for testing broth microdilution susceptibility of Flavobacterium columnare and F. psychrophilium to nine antimicrobials

USDA-ARS?s Scientific Manuscript database

A multi-laboratory broth microdilution method trial was performed to standardize the specialized test conditions required for fish pathogens Flavobacterium columnare and F. pyschrophilum. Nine laboratories tested the quality control (QC) strains Escherichia coli ATCC 25922 and Aeromonas salmonicid...

OZONE AMBIENT AIR QUALITY STANDARD HAS BENEFICIAL EFFECT ON PONDEROSA PINE IN CALIFORNIA

EPA Science Inventory

Ambient air quality standards and control strategies are implemented to protect humans and vegetation from adverse effects. However, to date there has not been a simple and objective method to determine if the standards and resultant control strategies have reduced O3 impacts on ...

Use of NDT equipment for construction quality control of hot mix asphalt pavements

DOT National Transportation Integrated Search

2006-08-01

The focus of the study has been to evaluate the utility of seismic methods in the quality management of the hot mix asphalt layers. Procedures are presented to measure the target field moduli of hot mix asphalt (HMA) with laboratory seismic methods, ...

[Investigation on pattern and methods of quality control for Chinese materia medica based on dao-di herbs and bioassay - bioassay for Coptis chinensis].

PubMed

Yan, Dan; Xiao, Xiao-he

2011-05-01

Establishment of bioassay methods is the technical issues to be faced with in the bioassay of Chinese materia medica. Taking the bioassay of Coptis chinensis Franch. as an example, the establishment process and application of the bioassay methods (including bio-potency and bio-activity fingerprint) were explained from the aspects of methodology, principle of selection, experimental design, method confirmation and data analysis. The common technologies were extracted and formed with the above aspects, so as to provide technical support for constructing pattern and method of the quality control for Chinese materia medica based on the dao-di herbs and bioassay.

Quality-assurance data for routine water quality analyses by the U. S. Geological Survey laboratory in Troy, New York; July 1993 through June 1995

USGS Publications Warehouse

Lincoln, Tricia A.; Horan-Ross, Debra A.; McHale, Michael R.; Lawrence, Gregory B.

2001-01-01

A laboratory for analysis of low-ionic strength water has been developed at the U.S. Geological Survey (USGS) office in Troy, N.Y., to analyze samples collected by USGS projects in the Northeast. The laboratory's quality-assurance program is based on internal and interlaboratory quality-assurance samples and quality-control procedures developed to ensure proper sample collection, processing, and analysis. The quality-assurance/quality-control data are stored in the laboratory's SAS data-management system, which provides efficient review, compilation, and plotting of quality-assurance/quality-control data. This report presents and discusses samples analyzed from July 1993 through June 1995. Quality-control results for 18 analytical procedures were evaluated for bias and precision. Control charts show that data from seven of the analytical procedures were biased throughout the analysis period for either high-concentration or low-concentration samples but were within control limits; these procedures were: acid-neutralizing capacity, dissolved inorganic carbon, dissolved organic carbon (soil expulsions), chloride, magnesium, nitrate (colorimetric method), and pH. Three of the analytical procedures were occasionally biased but were within control limits; they were: calcium (high for high-concentration samples for May 1995), dissolved organic carbon (high for highconcentration samples from January through September 1994), and fluoride (high in samples for April and June 1994). No quality-control sample has been developed for the organic monomeric aluminum procedure. Results from the filter-blank and analytical-blank analyses indicate that all analytical procedures in which blanks were run were within control limits, although values for a few blanks were outside the control limits. Blanks were not analyzed for acid-neutralizing capacity, dissolved inorganic carbon, fluoride, nitrate (colorimetric method), or pH. Sampling and analysis precision are evaluated herein in terms of the coefficient of variation obtained for triplicate samples in 14 of the 18 procedures. Data-quality objectives were met by more than 90 percent of the samples analyzed in all procedures except total monomeric aluminum (85 percent of samples met objectives), total aluminum (70 percent of samples met objectives), and dissolved organic carbon (85 percent of samples met objectives). Triplicate samples were not analyzed for ammonium, fluoride, dissolved inorganic carbon, or nitrate (colorimetric method). Results of the USGS interlaboratory Standard Reference Sample Program indicated high data quality with a median result of 3.6 of a possible 4.0. Environment Canada's LRTAP interlaboratory study results indicated that more than 85 percent of the samples met data-quality objectives in 6 of the 12 analyses; exceptions were calcium, dissolved organic carbon, chloride, pH, potassium, and sodium. Data-quality objectives were not met for calcium samples in one LRTAP study, but 94 percent of samples analyzed were within control limits for the remaining studies. Data-quality objectives were not met by 35 percent of samples analyzed for dissolved organic carbon, but 94 percent of sample values were within 20 percent of the most probable value. Data-quality objectives were not met for 30 percent of samples analyzed for chloride, but 90 percent of sample values were within 20 percent of the most probable value. Measurements of samples with a pH above 6.0 were biased high in 54 percent of the samples, although 85 percent of the samples met data-quality objectives for pH measurements below 6.0. Data-quality objectives for potassium and sodium were not met in one study (only 33 percent of the samples analyzed met the objectives), although 85 percent of the sample values were within control limits for the other studies. Measured sodium values were above the upper control limit in all studies. Results from blind reference-sample analyses indicated that data

Modeling Canadian Quality Control Test Program for Steroid Hormone Receptors in Breast Cancer: Diagnostic Accuracy Study.

PubMed

Pérez, Teresa; Makrestsov, Nikita; Garatt, John; Torlakovic, Emina; Gilks, C Blake; Mallett, Susan

The Canadian Immunohistochemistry Quality Control program monitors clinical laboratory performance for estrogen receptor and progesterone receptor tests used in breast cancer treatment management in Canada. Current methods assess sensitivity and specificity at each time point, compared with a reference standard. We investigate alternative performance analysis methods to enhance the quality assessment. We used 3 methods of analysis: meta-analysis of sensitivity and specificity of each laboratory across all time points; sensitivity and specificity at each time point for each laboratory; and fitting models for repeated measurements to examine differences between laboratories adjusted by test and time point. Results show 88 laboratories participated in quality control at up to 13 time points using typically 37 to 54 histology samples. In meta-analysis across all time points no laboratories have sensitivity or specificity below 80%. Current methods, presenting sensitivity and specificity separately for each run, result in wide 95% confidence intervals, typically spanning 15% to 30%. Models of a single diagnostic outcome demonstrated that 82% to 100% of laboratories had no difference to reference standard for estrogen receptor and 75% to 100% for progesterone receptor, with the exception of 1 progesterone receptor run. Laboratories with significant differences to reference standard identified with Generalized Estimating Equation modeling also have reduced performance by meta-analysis across all time points. The Canadian Immunohistochemistry Quality Control program has a good design, and with this modeling approach has sufficient precision to measure performance at each time point and allow laboratories with a significantly lower performance to be targeted for advice.

Comprehensive HPTLC Fingerprinting for Quality Control of an Herbal Drug - The Case of Angelica gigas Root.

PubMed

Frommenwiler, Débora Arruda; Kim, Jonghwan; Yook, Chang-Soo; Tran, Thi Thu Trang; Cañigueral, Salvador; Reich, Eike

2018-04-01

The quality of herbal drugs is usually controlled using several tests recommended in a monograph. HPTLC is the method of choice for identification in many pharmacopoeias. If combined with a suitable reference material for comparison, HPTLC can provide information beyond identification and thus may simplify quality control. This paper describes, as a proof of concept, how HPTLC can be applied to define specifications for an herbal reference material and to control the quality of an herbal drug according to these specifications. Based on multiple batches of cultivated Angelica gigas root, a specific HPTLC method for identification was optimized. This method can distinguish 27 related species. It also can detect the presence of mixtures of A. gigas with two other Angelica species traded as "Dang gui" and is suitable as well for quantitative assessment of samples in a test for minimum content of the sum of decursin and decursinol angelate. The new concept of "comprehensive HPTLC fingerprinting" is proposed: HPTLC fingerprints (images), which are used for identification, are converted into peak profiles and the intensities of selected zones are quantitatively compared to those of the corresponding zones of the reference material. Following a collaborative trial involving three laboratories in three countries, the method was applied to check the quality of further candidates for establishing an appropriate reference material. In conclusion, this case demonstrates that a single HPTLC analysis can provide information about identity, purity, and minimum content of markers of an herbal drug. Georg Thieme Verlag KG Stuttgart · New York.

Water Quality Assessment for Deep-water Channel area of Guangzhou Port based on the Comprehensive Water Quality Identification Index Method

NASA Astrophysics Data System (ADS)

Chen, Yi

2018-03-01

The comprehensive water quality identification index method is able to assess the general water quality situation comprehensively and represent the water quality classification; water environment functional zone achieves pollution level and standard objectively and systematically. This paper selects 3 representative zones along deep-water channel of Guangzhou port and applies comprehensive water quality identification index method to calculate sea water quality monitoring data for different selected zones from year 2006 to 2014, in order to investigate the temporal variation of water quality along deep-water channel of Guangzhou port. The comprehensive water quality level from north to south presents an increased trend, and the water quality of the three zones in 2014 is much better than in 2006. This paper puts forward environmental protection measurements and suggestions for Pearl River Estuary, provides data support and theoretical basis for studied sea area pollution prevention and control.

Apparatus and method for combusting low quality fuel

DOEpatents

Brushwood, John Samuel; Pillsbury, Paul; Foote, John; Heilos, Andreas

2003-11-04

A gas turbine (12) capable of combusting a low quality gaseous fuel having a ratio of flammability limits less than 2, or a heat value below 100 BTU/SCF. A high quality fuel is burned simultaneously with the low quality fuel to eliminate instability in the combustion flame. A sensor (46) is used to monitor at least one parameter of the flame indicative of instability. A controller (50) having the sensor signal (48) as input is programmed to control the relative flow rates of the low quality and high quality fuels. When instability is detected, the flow rate of high quality fuel is automatically increased in relation to the flow rate of low quality fuel to restore stability.

CALL FOR PAPERS: 13th International Conference on Force and Mass Measurement

NASA Astrophysics Data System (ADS)

1992-01-01

10 14 May 1993, Helsinki Fair Centre, Finland Scope of the Conference The Conference reports and reviews the state of the art and future trends in force and mass measurements in science and industry. Emphasis is on the applications of new methods, current problems in calibration and quality control, as well as on advancements in new sensor technologies and industrial application of force and mass measurements. Main Themes and Topics 1. The state of the art and development trends in force and mass measurements Development and stability of high level mass standards Mass comparators and force standard machine New research topics in mass and force 2. Calibration and quality control Calibration methods Estimation of uncertainties and classification of accuracies Relations between calibration, testing and quality control Requirements for quality control Verification of weighing instruments and their main devices 3. Application of force and mass measurements Automatic weighing Mass flow measurements Quality control in process industry Sensor technologies Practical applications Special applications in industry, trade, etc. Deadline for submission of abstracts: 30 June 1992. For further information please contact: Finnish Society of Automation, Asemapäällikönkatu 12C, SF-00520 HELSINKI, Finland Phone: Int. +3580 1461 644, Fax: Int. +3580 1461 650

Towards a Visual Quality Metric for Digital Video

NASA Technical Reports Server (NTRS)

Watson, Andrew B.

1998-01-01

The advent of widespread distribution of digital video creates a need for automated methods for evaluating visual quality of digital video. This is particularly so since most digital video is compressed using lossy methods, which involve the controlled introduction of potentially visible artifacts. Compounding the problem is the bursty nature of digital video, which requires adaptive bit allocation based on visual quality metrics. In previous work, we have developed visual quality metrics for evaluating, controlling, and optimizing the quality of compressed still images. These metrics incorporate simplified models of human visual sensitivity to spatial and chromatic visual signals. The challenge of video quality metrics is to extend these simplified models to temporal signals as well. In this presentation I will discuss a number of the issues that must be resolved in the design of effective video quality metrics. Among these are spatial, temporal, and chromatic sensitivity and their interactions, visual masking, and implementation complexity. I will also touch on the question of how to evaluate the performance of these metrics.

Automated Assessment of Visual Quality of Digital Video

NASA Technical Reports Server (NTRS)

Watson, Andrew B.; Ellis, Stephen R. (Technical Monitor)

1997-01-01

The advent of widespread distribution of digital video creates a need for automated methods for evaluating visual quality of digital video. This is particularly so since most digital video is compressed using lossy methods, which involve the controlled introduction of potentially visible artifacts. Compounding the problem is the bursty nature of digital video, which requires adaptive bit allocation based on visual quality metrics. In previous work, we have developed visual quality metrics for evaluating, controlling, and optimizing the quality of compressed still images[1-4]. These metrics incorporate simplified models of human visual sensitivity to spatial and chromatic visual signals. The challenge of video quality metrics is to extend these simplified models to temporal signals as well. In this presentation I will discuss a number of the issues that must be resolved in the design of effective video quality metrics. Among these are spatial, temporal, and chromatic sensitivity and their interactions, visual masking, and implementation complexity. I will also touch on the question of how to evaluate the performance of these metrics.

Comparison of five Lonicera flowers by simultaneous determination of multi-components with single reference standard method and principal component analysis.

PubMed

Gao, Wen; Wang, Rui; Li, Dan; Liu, Ke; Chen, Jun; Li, Hui-Jun; Xu, Xiaojun; Li, Ping; Yang, Hua

2016-01-05

The flowers of Lonicera japonica Thunb. were extensively used to treat many diseases. As the demands for L. japonica increased, some related Lonicera plants were often confused or misused. Caffeoylquinic acids were always regarded as chemical markers in the quality control of L. japonica, but they could be found in all Lonicera species. Thus, a simple and reliable method for the evaluation of different Lonicera flowers is necessary to be established. In this work a method based on single standard to determine multi-components (SSDMC) combined with principal component analysis (PCA) for control and distinguish of Lonicera species flowers have been developed. Six components including three caffeoylquinic acids and three iridoid glycosides were assayed simultaneously using chlorogenic acid as the reference standard. The credibility and feasibility of the SSDMC method were carefully validated and the results demonstrated that there were no remarkable differences compared with external standard method. Finally, a total of fifty-one batches covering five Lonicera species were analyzed and PCA was successfully applied to distinguish the Lonicera species. This strategy simplifies the processes in the quality control of multiple-componential herbal medicine which effectively adapted for improving the quality control of those herbs belonging to closely related species. Copyright © 2015 Elsevier B.V. All rights reserved.

Method of Analysis by the U.S. Geological Survey California District Sacramento Laboratory?Determination of Trihalomethane Formation Potential, Method Validation, and Quality-Control Practices

USGS Publications Warehouse

Crepeau, Kathryn L.; Fram, Miranda S.; Bush, Noel

2004-01-01

An analytical method for the determination of the trihalomethane formation potential of water samples has been developed. The trihalomethane formation potential is measured by dosing samples with chlorine under specified conditions of pH, temperature, incubation time, darkness, and residual-free chlorine, and then analyzing the resulting trihalomethanes by purge and trap/gas chromatography equipped with an electron capture detector. Detailed explanations of the method and quality-control practices are provided. Method validation experiments showed that the trihalomethane formation potential varies as a function of time between sample collection and analysis, residual-free chlorine concentration, method of sample dilution, and the concentration of bromide in the sample.

Synthesis of the unmanned aerial vehicle remote control augmentation system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomczyk, Andrzej, E-mail: A.Tomczyk@prz.edu.pl

Medium size Unmanned Aerial Vehicle (UAV) usually flies as an autonomous aircraft including automatic take-off and landing phases. However in the case of the on-board control system failure, the remote steering is using as an emergency procedure. In this reason, remote manual control of unmanned aerial vehicle is used more often during take-of and landing phases. Depends on UAV take-off mass and speed (total energy) the potential crash can be very danger for airplane and environment. So, handling qualities of UAV is important from pilot-operator point of view. In many cases the dynamic properties of remote controlling UAV are notmore » suitable for obtaining the desired properties of the handling qualities. In this case the control augmentation system (CAS) should be applied. Because the potential failure of the on-board control system, the better solution is that the CAS algorithms are placed on the ground station computers. The method of UAV handling qualities shaping in the case of basic control system failure is presented in this paper. The main idea of this method is that UAV reaction on the operator steering signals should be similar - almost the same - as reaction of the 'ideal' remote control aircraft. The model following method was used for controller parameters calculations. The numerical example concerns the medium size MP-02A UAV applied as an aerial observer system.« less

46 CFR 160.133-9 - Preapproval review.

Code of Federal Regulations, 2012 CFR

2012-10-01

... manual as described in §§ 160.133-19 and 160.133-21 of this subpart; (7) A description of the quality... suppliers; (ii) The method for controlling the inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding inspection procedures; and (iv) The inspection...

46 CFR 160.133-9 - Preapproval review.

Code of Federal Regulations, 2013 CFR

2013-10-01

... manual as described in §§ 160.133-19 and 160.133-21 of this subpart; (7) A description of the quality... suppliers; (ii) The method for controlling the inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding inspection procedures; and (iv) The inspection...

46 CFR 160.170-9 - Preapproval review.

Code of Federal Regulations, 2014 CFR

2014-10-01

... manual as described in §§ 160.170-19 and 160.170-21 of this subpart; (7) A description of the quality... suppliers; (ii) The method for controlling the inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding inspection procedures; and (iv) The inspection...

46 CFR 160.170-9 - Preapproval review.

Code of Federal Regulations, 2013 CFR

2013-10-01

... manual as described in §§ 160.170-19 and 160.170-21 of this subpart; (7) A description of the quality... suppliers; (ii) The method for controlling the inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding inspection procedures; and (iv) The inspection...

46 CFR 160.133-9 - Preapproval review.

Code of Federal Regulations, 2014 CFR

2014-10-01

... manual as described in §§ 160.133-19 and 160.133-21 of this subpart; (7) A description of the quality... suppliers; (ii) The method for controlling the inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding inspection procedures; and (iv) The inspection...

46 CFR 160.170-9 - Preapproval review.

Code of Federal Regulations, 2012 CFR

2012-10-01

... manual as described in §§ 160.170-19 and 160.170-21 of this subpart; (7) A description of the quality... suppliers; (ii) The method for controlling the inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding inspection procedures; and (iv) The inspection...

Concepts of Quality in Student Assessment.

ERIC Educational Resources Information Center

Harlen, Wynne

This paper gives an overview of the methods of moderation, or quality assurance and quality control, as they may be more widely known, that are used to enhance the quality of student assessment. The discussion is based on the educational systems of the United Kingdom but is applicable to assessment in other countries. Quality in assessment is seen…

HIV quality report cards: impact of case-mix adjustment and statistical methods.

PubMed

Ohl, Michael E; Richardson, Kelly K; Goto, Michihiko; Vaughan-Sarrazin, Mary; Schweizer, Marin L; Perencevich, Eli N

2014-10-15

There will be increasing pressure to publicly report and rank the performance of healthcare systems on human immunodeficiency virus (HIV) quality measures. To inform discussion of public reporting, we evaluated the influence of case-mix adjustment when ranking individual care systems on the viral control quality measure. We used data from the Veterans Health Administration (VHA) HIV Clinical Case Registry and administrative databases to estimate case-mix adjusted viral control for 91 local systems caring for 12 368 patients. We compared results using 2 adjustment methods, the observed-to-expected estimator and the risk-standardized ratio. Overall, 10 913 patients (88.2%) achieved viral control (viral load ≤400 copies/mL). Prior to case-mix adjustment, system-level viral control ranged from 51% to 100%. Seventeen (19%) systems were labeled as low outliers (performance significantly below the overall mean) and 11 (12%) as high outliers. Adjustment for case mix (patient demographics, comorbidity, CD4 nadir, time on therapy, and income from VHA administrative databases) reduced the number of low outliers by approximately one-third, but results differed by method. The adjustment model had moderate discrimination (c statistic = 0.66), suggesting potential for unadjusted risk when using administrative data to measure case mix. Case-mix adjustment affects rankings of care systems on the viral control quality measure. Given the sensitivity of rankings to selection of case-mix adjustment methods-and potential for unadjusted risk when using variables limited to current administrative databases-the HIV care community should explore optimal methods for case-mix adjustment before moving forward with public reporting. Published by Oxford University Press on behalf of the Infectious Diseases Society of America 2014. This work is written by (a) US Government employee(s) and is in the public domain in the US.

JPEG2000 encoding with perceptual distortion control.

PubMed

Liu, Zhen; Karam, Lina J; Watson, Andrew B

2006-07-01

In this paper, a new encoding approach is proposed to control the JPEG2000 encoding in order to reach a desired perceptual quality. The new method is based on a vision model that incorporates various masking effects of human visual perception and a perceptual distortion metric that takes spatial and spectral summation of individual quantization errors into account. Compared with the conventional rate-based distortion minimization JPEG2000 encoding, the new method provides a way to generate consistent quality images at a lower bit rate.

Combining Nordtest method and bootstrap resampling for measurement uncertainty estimation of hematology analytes in a medical laboratory.

PubMed

Cui, Ming; Xu, Lili; Wang, Huimin; Ju, Shaoqing; Xu, Shuizhu; Jing, Rongrong

2017-12-01

Measurement uncertainty (MU) is a metrological concept, which can be used for objectively estimating the quality of test results in medical laboratories. The Nordtest guide recommends an approach that uses both internal quality control (IQC) and external quality assessment (EQA) data to evaluate the MU. Bootstrap resampling is employed to simulate the unknown distribution based on the mathematical statistics method using an existing small sample of data, where the aim is to transform the small sample into a large sample. However, there have been no reports of the utilization of this method in medical laboratories. Thus, this study applied the Nordtest guide approach based on bootstrap resampling for estimating the MU. We estimated the MU for the white blood cell (WBC) count, red blood cell (RBC) count, hemoglobin (Hb), and platelets (Plt). First, we used 6months of IQC data and 12months of EQA data to calculate the MU according to the Nordtest method. Second, we combined the Nordtest method and bootstrap resampling with the quality control data and calculated the MU using MATLAB software. We then compared the MU results obtained using the two approaches. The expanded uncertainty results determined for WBC, RBC, Hb, and Plt using the bootstrap resampling method were 4.39%, 2.43%, 3.04%, and 5.92%, respectively, and 4.38%, 2.42%, 3.02%, and 6.00% with the existing quality control data (U [k=2]). For WBC, RBC, Hb, and Plt, the differences between the results obtained using the two methods were lower than 1.33%. The expanded uncertainty values were all less than the target uncertainties. The bootstrap resampling method allows the statistical analysis of the MU. Combining the Nordtest method and bootstrap resampling is considered a suitable alternative method for estimating the MU. Copyright © 2017 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

[Feedforward control strategy and its application in quality improvement of ethanol precipitation process of danhong injection].

PubMed

Yan, Bin-Jun; Guo, Zheng-Tai; Qu, Hai-Bin; Zhao, Bu-Chang; Zhao, Tao

2013-06-01

In this work, a feedforward control strategy basing on the concept of quality by design was established for the manufacturing process of traditional Chinese medicine to reduce the impact of the quality variation of raw materials on drug. In the research, the ethanol precipitation process of Danhong injection was taken as an application case of the method established. Box-Behnken design of experiments was conducted. Mathematical models relating the attributes of the concentrate, the process parameters and the quality of the supernatants produced were established. Then an optimization model for calculating the best process parameters basing on the attributes of the concentrate was built. The quality of the supernatants produced by ethanol precipitation with optimized and non-optimized process parameters were compared. The results showed that using the feedforward control strategy for process parameters optimization can control the quality of the supernatants effectively. The feedforward control strategy proposed can enhance the batch-to-batch consistency of the supernatants produced by ethanol precipitation.

Can the Roche hemolysis index be used for automated determination of cell-free hemoglobin? A comparison to photometric assays.

PubMed

Petrova, Darinka Todorova; Cocisiu, Gabriela Ariadna; Eberle, Christoph; Rhode, Karl-Heinz; Brandhorst, Gunnar; Walson, Philip D; Oellerich, Michael

2013-09-01

The aim of this study was to develop a novel method for automated quantification of cell-free hemoglobin (fHb) based on the HI (Roche Diagnostics). The novel fHb method based on the HI was correlated with fHb measured using the triple wavelength methods of both Harboe [fHb, g/L = (0.915 * HI + 2.634)/100] and Fairbanks et al. [fHb, g/L = (0.917 * HI + 2.131)/100]. fHb concentrations were estimated from the HI using the Roche Modular automated platform in self-made and commercially available quality controls, as well as samples from a proficiency testing scheme (INSTAND). The fHb using Roche automated HI results were then compared to results obtained using the traditional spectrophotometric assays for one hundred plasma samples with varying degrees of hemolysis, lipemia and/or bilirubinemia. The novel method using automated HI quantification on the Roche Modular clinical chemistry platform correlated well with results using the classical methods in the 100 patient samples (Harboe: r = 0.9284; Fairbanks et al.: r = 0.9689) and recovery was good for self-made controls. However, commercially available quality controls showed poor recovery due to an unidentified matrix problem. The novel method produced reliable determination of fHb in samples without interferences. However, poor recovery using commercially available fHb quality control samples currently greatly limits its usefulness. © 2013.

WHO Working Group on revision of the Manual of Laboratory Methods for Testing DTP Vaccines-Report of two meetings held on 20-21 July 2006 and 28-30 March 2007, Geneva, Switzerland.

PubMed

Corbel, Michael J; Das, Rose Gaines; Lei, Dianliang; Xing, Dorothy K L; Horiuchi, Yoshinobu; Dobbelaer, Roland

2008-04-07

This report reflects the discussion and conclusions of a WHO group of experts from National Regulatory Authorities (NRAs), National Control Laboratories (NCLs), vaccine industries and other relevant institutions involved in standardization and control of diphtheria, tetanus and pertussis vaccines (DTP), held on 20-21 July 2006 and 28-30 March 2007, in Geneva Switzerland for the revision of WHO Manual for quality control of DTP vaccines. Taking into account recent developments and standardization in quality control methods and the revision of WHO recommendations for D, T, P vaccines, and a need for updating the manual has been recognized. In these two meetings the current situation of quality control methods in terms of potency, safety and identity tests for DTP vaccines and statistical analysis of data were reviewed. Based on the WHO recommendations and recent validation of testing methods, the content of current manual were reviewed and discussed. The group agreed that the principles to be observed in selecting methods included identifying those critical for assuring safety, efficacy and quality and which were consistent with WHO recommendations/requirements. Methods that were well recognized but not yet included in current Recommendations should be taken into account. These would include in vivo and/or in vitro methods for determining potency, safety testing and identity. The statistical analysis of the data should be revised and updated. It was noted that the mouse based assays for toxoid potency were still quite widely used and it was desirable to establish appropriate standards for these to enable the results to be related to the standard guinea pig assays. The working group was met again to review the first drafts and to input further suggestions or amendments to the contributions of the drafting groups. The revised manual was to be finalized and published by WHO.

Preliminary study of ultrasonic structural quality control of Swiss-type cheese.

PubMed

Eskelinen, J J; Alavuotunki, A P; Haeggström, E; Alatossava, T

2007-09-01

There is demand for a new nondestructive cheese-structure analysis method for Swiss-type cheese. Such a method would provide the cheese-making industry the means to enhance process control and quality assurance. This paper presents a feasibility study on ultrasonic monitoring of the structural quality of Swiss cheese by using a single-transducer 2-MHz longitudinal mode pulse-echo setup. A volumetric ultrasonic image of a cheese sample featuring gas holes (cheese-eyes) and defects (cracks) in the scan area is presented. The image is compared with an optical reference image constructed from dissection images of the same sample. The results show that the ultrasonic method is capable of monitoring the gas-solid structure of the cheese during the ripening process. Moreover, the method can be used to detect and to characterize cheese-eyes and cracks in ripened cheese. Industrial application demands were taken into account when conducting the measurements.

Microbiological water methods: quality control measures for Federal Clean Water Act and Safe Drinking Water Act regulatory compliance.

PubMed

Root, Patsy; Hunt, Margo; Fjeld, Karla; Kundrat, Laurie

2014-01-01

Quality assurance (QA) and quality control (QC) data are required in order to have confidence in the results from analytical tests and the equipment used to produce those results. Some AOAC water methods include specific QA/QC procedures, frequencies, and acceptance criteria, but these are considered to be the minimum controls needed to perform a microbiological method successfully. Some regulatory programs, such as those at Code of Federal Regulations (CFR), Title 40, Part 136.7 for chemistry methods, require additional QA/QC measures beyond those listed in the method, which can also apply to microbiological methods. Essential QA/QC measures include sterility checks, reagent specificity and sensitivity checks, assessment of each analyst's capabilities, analysis of blind check samples, and evaluation of the presence of laboratory contamination and instrument calibration and checks. The details of these procedures, their performance frequency, and expected results are set out in this report as they apply to microbiological methods. The specific regulatory requirements of CFR Title 40 Part 136.7 for the Clean Water Act, the laboratory certification requirements of CFR Title 40 Part 141 for the Safe Drinking Water Act, and the International Organization for Standardization 17025 accreditation requirements under The NELAC Institute are also discussed.

Taguchi's off line method and Multivariate loss function approach for quality management and optimization of process parameters -A review

NASA Astrophysics Data System (ADS)

Bharti, P. K.; Khan, M. I.; Singh, Harbinder

2010-10-01

Off-line quality control is considered to be an effective approach to improve product quality at a relatively low cost. The Taguchi method is one of the conventional approaches for this purpose. Through this approach, engineers can determine a feasible combination of design parameters such that the variability of a product's response can be reduced and the mean is close to the desired target. The traditional Taguchi method was focused on ensuring good performance at the parameter design stage with one quality characteristic, but most products and processes have multiple quality characteristics. The optimal parameter design minimizes the total quality loss for multiple quality characteristics. Several studies have presented approaches addressing multiple quality characteristics. Most of these papers were concerned with maximizing the parameter combination of signal to noise (SN) ratios. The results reveal the advantages of this approach are that the optimal parameter design is the same as the traditional Taguchi method for the single quality characteristic; the optimal design maximizes the amount of reduction of total quality loss for multiple quality characteristics. This paper presents a literature review on solving multi-response problems in the Taguchi method and its successful implementation in various industries.

Light-leaking region segmentation of FOG fiber based on quality evaluation of infrared image

NASA Astrophysics Data System (ADS)

Liu, Haoting; Wang, Wei; Gao, Feng; Shan, Lianjie; Ma, Yuzhou; Ge, Wenqian

2014-07-01

To improve the assembly reliability of Fiber Optic Gyroscope (FOG), a light leakage detection system and method is developed. First, an agile movement control platform is designed to implement the pose control of FOG optical path component in 6 Degrees of Freedom (DOF). Second, an infrared camera is employed to capture the working state images of corresponding fibers in optical path component after the manual assembly of FOG; therefore the entire light transmission process of key sections in light-path can be recorded. Third, an image quality evaluation based region segmentation method is developed for the light leakage images. In contrast to the traditional methods, the image quality metrics, including the region contrast, the edge blur, and the image noise level, are firstly considered to distinguish the image characters of infrared image; then the robust segmentation algorithms, including graph cut and flood fill, are all developed for region segmentation according to the specific image quality. Finally, after the image segmentation of light leakage region, the typical light-leaking type, such as the point defect, the wedge defect, and the surface defect can be identified. By using the image quality based method, the applicability of our proposed system can be improved dramatically. Many experiment results have proved the validity and effectiveness of this method.

WELDSMART: A vision-based expert system for quality control

NASA Technical Reports Server (NTRS)

Andersen, Kristinn; Barnett, Robert Joel; Springfield, James F.; Cook, George E.

1992-01-01

This work was aimed at exploring means for utilizing computer technology in quality inspection and evaluation. Inspection of metallic welds was selected as the main application for this development and primary emphasis was placed on visual inspection, as opposed to other inspection methods, such as radiographic techniques. Emphasis was placed on methodologies with the potential for use in real-time quality control systems. Because quality evaluation is somewhat subjective, despite various efforts to classify discontinuities and standardize inspection methods, the task of using a computer for both inspection and evaluation was not trivial. The work started out with a review of the various inspection techniques that are used for quality control in welding. Among other observations from this review was the finding that most weld defects result in abnormalities that may be seen by visual inspection. This supports the approach of emphasizing visual inspection for this work. Quality control consists of two phases: (1) identification of weld discontinuities (some of which may be severe enough to be classified as defects), and (2) assessment or evaluation of the weld based on the observed discontinuities. Usually the latter phase results in a pass/fail judgement for the inspected piece. It is the conclusion of this work that the first of the above tasks, identification of discontinuities, is the most challenging one. It calls for sophisticated image processing and image analysis techniques, and frequently ad hoc methods have to be developed to identify specific features in the weld image. The difficulty of this task is generally not due to limited computing power. In most cases it was found that a modest personal computer or workstation could carry out most computations in a reasonably short time period. Rather, the algorithms and methods necessary for identifying weld discontinuities were in some cases limited. The fact that specific techniques were finally developed and successfully demosntrated to work illustrates that the general approach taken here appears to be promising for commercial development of computerized quality inspection systems. Inspection based on these techniques may be used to supplement or substitute more elaborate inspection methods, such as x-ray inspections.

Evaluation of statistical protocols for quality control of ecosystem carbon dioxide fluxes

Treesearch

Jorge F. Perez-Quezada; Nicanor Z. Saliendra; William E. Emmerich; Emilio A. Laca

2007-01-01

The process of quality control of micrometeorological and carbon dioxide (CO2) flux data can be subjective and may lack repeatability, which would undermine the results of many studies. Multivariate statistical methods and time series analysis were used together and independently to detect and replace outliers in CO2 flux...

Quality Control of an OSCE Using Generalizability Theory and Many-Faceted Rasch Measurement

ERIC Educational Resources Information Center

Iramaneerat, Cherdsak; Yudkowsky, Rachel; Myford, Carol M.; Downing, Steven M.

2008-01-01

An Objective Structured Clinical Examination (OSCE) is an effective method for evaluating competencies. However, scores obtained from an OSCE are vulnerable to many potential measurement errors that cases, items, or standardized patients (SPs) can introduce. Monitoring these sources of errors is an important quality control mechanism to ensure…

Measuring the quality of infection control in Dutch nursing homes using a standardized method; the Infection prevention RIsk Scan (IRIS)

PubMed Central

2014-01-01

Background We developed a standardised method to assess the quality of infection control in Dutch Nursing Home (NH), based on a cross-sectional survey that visualises the results. The method was called the Infection control RIsk Infection Scan (IRIS). We tested the applicability of this new tool in a multicentre surveillance executed June and July 2012. Methods The IRIS includes two patient outcome-variables, i.e. the prevalence of healthcare associated infections (HAI) and rectal carriage of Extended-Spectrum Beta-Lactamase (ESBL) producing Enterobacteriaceae (ESBL-E); two patient-related risk factors, i.e. use of medical devices, and antimicrobial therapy; and three ward-related risk factors, i.e. environmental contamination, availability of local guidelines, and shortcomings in infection prevention preconditions. Results were categorised as low-, intermediate- and high risk, presented in an easy-to-read graphic risk spider-plot. This plot was given as feedback to management and healthcare workers of the NH. Results Large differences were found among most the variables in the different NH. Common shortcomings were the availability of infection control guidelines and the level of environmental cleaning. Most striking differences were observed in the prevalence of ESBL carriage, ranged from zero to 20.6% (p < 0.001). Conclusions The IRIS provided a rapid and easy to understand assessment of the infection control situation of the participating NH. The results can be used to improve the quality of infection control based on the specific needs of a NH but needs further validation in future studies. Repeated measurement can determine the effectiveness of the interventions. This makes the IRIS a useful tool for quality systems. PMID:25243067

A multiparametric automatic method to monitor long-term reproducibility in digital mammography: results from a regional screening programme.

PubMed

Gennaro, G; Ballaminut, A; Contento, G

2017-09-01

This study aims to illustrate a multiparametric automatic method for monitoring long-term reproducibility of digital mammography systems, and its application on a large scale. Twenty-five digital mammography systems employed within a regional screening programme were controlled weekly using the same type of phantom, whose images were analysed by an automatic software tool. To assess system reproducibility levels, 15 image quality indices (IQIs) were extracted and compared with the corresponding indices previously determined by a baseline procedure. The coefficients of variation (COVs) of the IQIs were used to assess the overall variability. A total of 2553 phantom images were collected from the 25 digital mammography systems from March 2013 to December 2014. Most of the systems showed excellent image quality reproducibility over the surveillance interval, with mean variability below 5%. Variability of each IQI was 5%, with the exception of one index associated with the smallest phantom objects (0.25 mm), which was below 10%. The method applied for reproducibility tests-multi-detail phantoms, cloud automatic software tool to measure multiple image quality indices and statistical process control-was proven to be effective and applicable on a large scale and to any type of digital mammography system. • Reproducibility of mammography image quality should be monitored by appropriate quality controls. • Use of automatic software tools allows image quality evaluation by multiple indices. • System reproducibility can be assessed comparing current index value with baseline data. • Overall system reproducibility of modern digital mammography systems is excellent. • The method proposed and applied is cost-effective and easily scalable.

Method for Examination and Documentation of Basic Information and Metadata from Published Reports Relevant to the Study of Stormwater Runoff Quality

USGS Publications Warehouse

Dionne, Shannon G.; Granato, Gregory E.; Tana, Cameron K.

1999-01-01

A readily accessible archive of information that is valid, current, and technically defensible is needed to make informed highway-planning, design, and management decisions. The National Highway Runoff Water-Quality Data and Methodology Synthesis (NDAMS) is a cataloging and assessment of the documentation of information relevant to highway-runoff water quality available in published reports. The report review process is based on the NDAMS review sheet, which was designed by the USGS with input from the FHWA, State transportation agencies, and the regulatory community. The report-review process is designed to determine the technical merit of the existing literature in terms of current requirements for data documentation, data quality, quality assurance and quality control (QA/QC), and technical issues that may affect the use of historical data. To facilitate the review process, the NDAMS review sheet is divided into 12 sections: (1) administrative review information, (2) investigation and report information, (3) temporal information, (4) location information (5) water-quality-monitoring information, (6) sample-handling methods, (7) constituent information, (8) sampling focus and matrix, (9) flow monitoring methods, (10) field QA/QC, (11) laboratory, and (12) uncertainty/error analysis. This report describes the NDAMS report reviews and metadata documentation methods and provides an overview of the approach and of the quality-assurance and quality-control program used to implement the review process. Detailed information, including a glossary of relevant terms, a copy of the report-review sheets, and reportreview instructions are completely documented in a series of three appendixes included with this report. Therefore the reviews are repeatable and the methods can be used by transportation research organizations to catalog new reports as they are published.

Simultaneous Determination of Ten Constituents in Chaiqin Qingning Capsule by High-performance Liquid Chromatography Coupled with Triple-quadrupole Mass Spectrometry

PubMed Central

Li, Ting Yu; Huo, Xiao Kui; Zheng, Lu; Wang, Chao; Cong, Hai Jian; Xiang, Ting; Zhang, Lin; Zhang, Bao Jing; Huang, Shan Shan; Wu, Bin; Li, Xin Yu

2017-01-01

Background: Chaiqin Qingning Capsule (CQQNC) was a prescription of Traditional Chinese Medicine with the effects of clearing away heat and removing toxin, harmonizing the exterior and interior, it was widely used in Asian, for example, China and Japan, different batches of the raws materials and different processing time may be the vital factor which raised a challenge to control the quality of the CQQNC. Experimental Methods: In this experiment, a high-performance liquid chromatography-mass spectrometry/MS (HPLC-MS/MS) method was developed to simultaneously determine ten bioactive components for the quality control of CQQNC. Chromatographic separation was achieved using an XBridge BEH C18 column (150 mm × 4.6 mm, 2.5 μm) with a mobile phase composed of 10 mm aqueous ammonium acetate and acetonitrile using a gradient elution in 20 min. This study was conducted by multiple reaction monitoring mode through electrospray ionization resource with a negative ionization mode. Results: The established method was validated with good performance of precision, accuracy, stability, and reproducibility and was utilized to simultaneously quantify ten constituents of CQQNC obtained from seven different batches. Conclusion: It is the first time to report the rapid and simultaneous analysis of the ten compounds in CQQNC by HPLC-MS/MS and apply to determine 10 constituents in 7 batches of CQQNC bought from drug store in china. This method could be considered as good quality criteria to control the quality of CQQNC. SUMMARY In this paper, a simple, specific, and rapid high-performance liquid chromatogram coupled with triple-quadrupole mass spectrometry method for simultaneous quantification of ten constituents in Chaiqin Qingning Capsule has been developed for the first time. This method could be considered as good quality criteria to control the quality of CQQNC. Abbreviations used: CHM: Chinese herbal medicine; TCM: Traditional Chinese Medicine; CQQNC: Triple-quadrupole mass spectrometry Chaiqin Qingning Capsules; HPLC–MS/MS: High liquid chromatography equipped with tandem mass spectrometry; ESI: Electrospray ionization; DP: Declustering potential; CE: Collision energy; RSD: Relative standard deviation; LOD: Limit of detection; LOQ: Limit of quantity. PMID:29200714

Volume 3 - Area Sources and Area Source Method Abstracts

EPA Pesticide Factsheets

Nonpoint (area) source emission reference materials from the EIIP. Provides nonpoint source guidance on planning, emissions estimation, data collection, inventory documentation and reporting, and quality assurance/quality control.

Method of Analysis by the U.S. Geological Survey California District Sacramento Laboratory-- Determination of Dissolved Organic Carbon in Water by High Temperature Catalytic Oxidation, Method Validation, and Quality-Control Practices

USGS Publications Warehouse

Bird, Susan M.; Fram, Miranda S.; Crepeau, Kathryn L.

2003-01-01

An analytical method has been developed for the determination of dissolved organic carbon concentration in water samples. This method includes the results of the tests used to validate the method and the quality-control practices used for dissolved organic carbon analysis. Prior to analysis, water samples are filtered to remove suspended particulate matter. A Shimadzu TOC-5000A Total Organic Carbon Analyzer in the nonpurgeable organic carbon mode is used to analyze the samples by high temperature catalytic oxidation. The analysis usually is completed within 48 hours of sample collection. The laboratory reporting level is 0.22 milligrams per liter.

Integrated Aerodynamic and Control System Design of Oblique Wing Aircraft. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Morris, Stephen James

1990-01-01

An efficient high speed aircraft design must achieve a high lift to drag ratio at transonic and supersonic speeds. In 1952 Dr. R. T. Jones proved that for any flight Mach number minimum drag at a fixed lift is achieved by an elliptic wing planform with an appropriate oblique sweep angle. Since then, wind tunnel tests and numerical flow models have confirmed that the compressibility drag of oblique wing aircraft is lower than similar symmetrical sweep designs. At oblique sweep angles above thirty degrees the highly asymmetric planform gives rise to aerodynamic and inertia couplings which affect stability and degrade the aircraft's handling qualities. In the case of the NASA-Rockwell Oblique Wing Research Aircraft, attempts to improve the handling qualities by implementing a stability augmentation system have produced unsatisfactory results because of an inherent lack of controllability in the proposed design. The present work focuses on improving the handling qualities of oblique wing aircraft by including aerodynamic configuration parameters as variables in the control system synthesis to provide additional degrees of freedom with which to further decouple the aircraft's response. Handling qualities are measured using a quadratic cost function identical to that considered in optimal control problems, but the controller architecture is not restricted to full state feedback. An optimization procedure is used to simultaneously solve for the aircraft configuration and control gains which maximize a handling qualities measure, while meeting imposed constraints on trim. In some designs wing flexibility is also modeled and reduced order controllers are implemented. Oblique wing aircraft synthesized by this integrated design method show significant improvement in handling qualities when compared to the originally proposed closed loop aircraft. The integrated design synthesis method is then extended to show how handling qualities may be traded for other types of mission performance (drag, weight, etc.). Examples are presented which show how performance can be maximized while maintaining a desired level of handling quality.

Distributed sensor architecture for intelligent control that supports quality of control and quality of service.

PubMed

Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

2015-02-25

This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems.

Distributed Sensor Architecture for Intelligent Control that Supports Quality of Control and Quality of Service

PubMed Central

Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

2015-01-01

This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems. PMID:25723145

Inverse simulation system for evaluating handling qualities during rendezvous and docking

NASA Astrophysics Data System (ADS)

Zhou, Wanmeng; Wang, Hua; Thomson, Douglas; Tang, Guojin; Zhang, Fan

2017-08-01

The traditional method used for handling qualities assessment of manned space vehicles is too time-consuming to meet the requirements of an increasingly fast design process. In this study, a rendezvous and docking inverse simulation system to assess the handling qualities of spacecraft is proposed using a previously developed model-predictive-control architecture. By considering the fixed discrete force of the thrusters of the system, the inverse model is constructed using the least squares estimation method with a hyper-ellipsoidal restriction, the continuous control outputs of which are subsequently dispersed by pulse width modulation with sensitivity factors introduced. The inputs in every step are deemed constant parameters, and the method could be considered as a general method for solving nominal, redundant, and insufficient inverse problems. The rendezvous and docking inverse simulation is applied to a nine-degrees-of-freedom platform, and a novel handling qualities evaluation scheme is established according to the operation precision and astronauts' workload. Finally, different nominal trajectories are scored by the inverse simulation and an established evaluation scheme. The scores can offer theoretical guidance for astronaut training and more complex operation missions.

[Development of new approaches for objective dental tissue characteristiсs reproduction for preparation of highly aesthetical restoration].

PubMed

Makeeva, I M; Moskalev, E E; Kuz'ko, E I

2010-01-01

A new method of color quality control based on spectrophotometry has been developed for dental restoration. A comparative analysis of quality of subjective color control by trained and non-trained observers has been made. Based on comparative analysis of the results of subjective color-control and spectrophotometry the maximum amount of allowed color difference has been set (dE=2.8).

HDP for the Neutralized pH Value Control in the Clarifying Process of Sugar Cane Juice

NASA Astrophysics Data System (ADS)

Lin, Xiaofeng; Yang, Jiaran

2009-05-01

Neutralizing pH value of sugar cane juice is the important craft in the control process in the clarifying process of sugar cane juice, which is the important factor to influence output and the quality of white sugar. On the one hand, it is an important content to control the neutralized pH value within a required range, which has the vital significance for acquiring high quality purified juice, reducing energy consumption and raising sucrose recovery. On the other hand, it is a complicated physical-chemistry process, which has the characteristics of strong non-linearity, time-varying, large time-delay, and multi-input. Therefore, there has not been a very good solution to control the neutralized pH value. Firstly, in this chapter, a neural network model for the clarifying process of sugar juice is established based on gathering 1200 groups of real-time sample data in a sugar factory. Then, the HDP (Heuristic Dynamic Programming) method is used to optimize and control the neutralized pH value in the clarifying process of sugar juice. Simulation results indicate that this method has good control effect. This will build a good foundation for stabilizing the clarifying process and enhancing the quality of the purified juice and lastly enhancing the quality of white sugar.

Automated image quality assessment for chest CT scans.

PubMed

Reeves, Anthony P; Xie, Yiting; Liu, Shuang

2018-02-01

Medical image quality needs to be maintained at standards sufficient for effective clinical reading. Automated computer analytic methods may be applied to medical images for quality assessment. For chest CT scans in a lung cancer screening context, an automated quality assessment method is presented that characterizes image noise and image intensity calibration. This is achieved by image measurements in three automatically segmented homogeneous regions of the scan: external air, trachea lumen air, and descending aorta blood. Profiles of CT scanner behavior are also computed. The method has been evaluated on both phantom and real low-dose chest CT scans and results show that repeatable noise and calibration measures may be realized by automated computer algorithms. Noise and calibration profiles show relevant differences between different scanners and protocols. Automated image quality assessment may be useful for quality control for lung cancer screening and may enable performance improvements to automated computer analysis methods. © 2017 American Association of Physicists in Medicine.

Internal quality assurance in a clinical virology laboratory. II. Internal quality control.

PubMed Central

Gray, J J; Wreghitt, T G; McKee, T A; McIntyre, P; Roth, C E; Smith, D J; Sutehall, G; Higgins, G; Geraghty, R; Whetstone, R

1995-01-01

AIMS--In April 1991 additional quality control procedures were introduced into the virology section of the Clinical Microbiology and Public Health Laboratory, Cambridge. Internal quality control (IQC) samples were gradually included in the serological assays performed in the laboratory and supplemented kit controls and standard sera. METHODS--From April 1991 to December 1993, 2421 IQC procedures were carried out with reference sera. RESULTS--The IQC samples were evaluated according to the Westgard rules. Violations were recorded in 60 of 1808 (3.3%) controls and were highest in the IQC samples of complement fixation tests (25/312 (8%) of controls submitted for complement fixation tests). CONCLUSIONS--The inclusion of IQC samples in the serological assays performed in the laboratory has highlighted batch to batch variation in commercial assays. The setting of acceptable limits for the IQC samples has increased confidence in the validity of assay results. PMID:7730475

Instrumental Surveillance of Water Quality.

ERIC Educational Resources Information Center

Miller, J. A.; And Others

The role analytical instrumentation performs in the surveillance and control of the quality of water resources is reviewed. Commonly performed analyses may range from simple tests for physical parameters to more highly sophisticated radiological or spectrophotometric methods. This publication explores many of these types of water quality analyses…

Quality Control System using Simple Implementation of Seven Tools for Batik Textile Manufacturing

NASA Astrophysics Data System (ADS)

Ragil Suryoputro, Muhammad; Sugarindra, Muchamad; Erfaisalsyah, Hendy

2017-06-01

In order to produce better products and mitigate defect in products, every company must implement a quality control system. Company will find means to implement a quality control system that is capable and reliable. One of the methods is using the simple implementation of the seven tools in quality control defects. The case studied in this research was the level of disability xyz grey fabric on a shuttle loom 2 on the Batik manufacturing company. The seven tools that include: flowchart, check sheet, histogram, scatter diagram combined with control charts, Pareto diagrams and fishbone diagrams (causal diagram). Check sheet results obtained types of defects in the grey fabric was woven xyz is warp, double warp, the warp break, double warp, empty warp, warp tenuous, ugly edges, thick warp, and rust. Based on the analysis of control chart indicates that the process is out of control. This can be seen in the graph control where there is still a lot of outlier data. Based on a scatter diagram shows a positive correlation between the percentage of disability and the number of production. Based on Pareto diagram, repair needs priority is for the dominant type of defect is warp (44%) and based on double warp value histogram is also the highest with a value of 23635.11 m. In addition, based on the analysis of the factors causing defect by fishbone diagram double warp or other types of defects originating from the materials, methods, machines, measurements, man and environment. Thus the company can take to minimize the prevention and repair of defects and improve product quality.

Power Quality Improvement Utilizing Photovoltaic Generation Connected to a Weak Grid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muljadi, Eduard; Tumbelaka, Hanny H.; Gao, Wenzhong

Microgrid research and development in the past decades have been one of the most popular topics. Similarly, the photovoltaic generation has been surging among renewable generation in the past few years, thanks to the availability, affordability, technology maturity of the PV panels and the PV inverter in the general market. Unfortunately, quite often, the PV installations are connected to weak grids and may have been considered as the culprit of poor power quality affecting other loads in particular sensitive loads connected to the same point of common coupling (PCC). This paper is intended to demystify the renewable generation, and turnsmore » the negative perception into positive revelation of the superiority of PV generation to the power quality improvement in a microgrid system. The main objective of this work is to develop a control method for the PV inverter so that the power quality at the PCC will be improved under various disturbances. The method is to control the reactive current based on utilizing the grid current to counteract the negative impact of the disturbances. The proposed control method is verified in PSIM platform. Promising results have been obtained.« less

Polymerase Chain Reaction/Rapid Methods Are Gaining a Foothold in Developing Countries.

PubMed

Ragheb, Suzan Mohammed; Jimenez, Luis

Detection of microbial contamination in pharmaceutical raw materials and finished products is a critical factor to guarantee their safety, stability, and potency. Rapid microbiological methods-such as polymerase chain reaction-have been widely applied to clinical and food quality control analysis. However, polymerase chain reaction applications to pharmaceutical quality control have been rather slow and sporadic. Successful implementation of these methods in pharmaceutical companies in developing countries requires important considerations to provide sensitive and robust assays that will comply with good manufacturing practices. In recent years several publications have encouraged the application of molecular techniques in the microbiological assessment of pharmaceuticals. One of these techniques is polymerase chain reaction (PCR). The successful application of PCR in the pharmaceutical industry in developing countries is governed by considerable factors and requirements. These factors include the setting up of a PCR laboratory and the choice of appropriate equipment and reagents. In addition, the presence of well-trained analysts and establishment of quality control and quality assurance programs are important requirements. The pharmaceutical firms should take into account these factors to allow better chances for regulatory acceptance and wide application of this technique. © PDA, Inc. 2014.

Advances in the control of wine spoilage by Zygosaccharomyces and Dekkera/Brettanomyces.

PubMed

Zuehlke, J M; Petrova, B; Edwards, C G

2013-01-01

Understanding the characteristics of yeast spoilage, as well as the available control technologies, is vital to producing consistent, high-quality wine. Zygosaccharomyces bailii contamination may result in refermentation and CO2 production in sweet wines or grape juice concentrate, whereas Brettanomyces bruxellensis spoilage often contributes off-odors and flavors to red wines. Early detection of these yeasts by selective/differential media or genetic methods is important to minimize potential spoilage. More established methods of microbial control include sulfur dioxide, dimethyl dicarbonate, and filtration. Current research is focused on the use of chitosan, pulsed electric fields, low electric current, and ultrasonics as means to protect wine quality.

[Application of adaptive canceling methods in temperature control in ultrasonic therapeutical treatment].

PubMed

Deng, Jun; Liu, Du-ren

2002-12-01

Objective. To improve the quality of ultrasonic therapeutical treatment by improving the accuracy of temperature control. Method. Adaptive canceling methods were used to reduce the noise of temperature signal gained, and enhance signal-to-noise ratio. Result. The test's result corresponds basically to the theoretical curve. Conclusion. Adaptive canceling methods can be applied to clinic treatment.

Collaborative study for the validation of alternative in vitro potency assays for human tetanus immunoglobulins.

PubMed

Gross, S; Janssen, S W J; de Vries, B; Terao, E; Daas, A; Buchheit, K-H

2010-07-01

An international collaborative study to validate 2 alternative in vitro methods for the potency testing of human tetanus immunoglobulin products was organised by the European Directorate for the Quality of Medicines & HealthCare (EDQM). The study, run in the framework of the Biological Standardisation Programme (BSP) under the aegis of the European Commission and the Council of Europe, involved 21 official medicines control and industry laboratories from 15 countries. Both methods, an enzyme-linked immunoassay (EIA) and a toxoid inhibition assay (TIA), showed good reproducibility, repeatability and precision. EIA and TIA discriminated between low, medium and high potency samples. Potency estimates correlated well and both values were in close agreement with those obtained by in vivo methods. Moreover, these alternative methods allowed to resolve discrepant results between laboratories that were due to product potency loss and reporting errors. The study demonstrated that EIA and TIA are suitable quality control methods for tetanus immunoglobulin, which can be standardised in a control laboratory using a quality assurance system. Consequently, the Group of Experts on Human Blood and Blood Products of the European Pharmacopoeia revised the monograph on human tetanus immunoglobulins to include both the methods as compendial alternatives to the in vivo mouse challenge assay. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

Study on Quality Standard of Processed Curcuma Longa Radix

PubMed Central

Zhao, Yongfeng; Quan, Liang; Zhou, Haiting; Cao, Dong; Li, Wenbing; Yang, Zhuo

2017-01-01

To control the quality of Curcuma Longa Radix by establishing quality standards, this paper increased the contents of extract and volatile oil determination. Meanwhile, the curcumin was selected as the internal marker, and the relative correlation factors (RCFs) of demethoxycurcumin and bisdemethoxycurcumin were established by high performance liquid chromatography (HPLC). The contents of multicomponents were calculated based on their RCFs. The rationality and feasibility of the methods were evaluated by comparison of the quantitative results between external standard method (ESM) and quantitative analysis of multicomponents by single-marker (QAMS). Ethanol extracts ranged from 9.749 to 15.644% and the mean value was 13.473%. The volatile oil ranged from 0.45 to 0.90 mL/100 g and the mean value was 0.66 mL/100 g. This method was accurate and feasible and could provide a reference for further comprehensive and effective control of the quality standard of Curcuma Longa Radix and its processed products. PMID:29375640

[Methodological quality and reporting quality evaluation of randomized controlled trials published in China Journal of Chinese Materia Medica].

PubMed

Yu, Dan-Dan; Xie, Yan-Ming; Liao, Xing; Zhi, Ying-Jie; Jiang, Jun-Jie; Chen, Wei

2018-02-01

To evaluate the methodological quality and reporting quality of randomized controlled trials(RCTs) published in China Journal of Chinese Materia Medica, we searched CNKI and China Journal of Chinese Materia webpage to collect RCTs since the establishment of the magazine. The Cochrane risk of bias assessment tool was used to evaluate the methodological quality of RCTs. The CONSORT 2010 list was adopted as reporting quality evaluating tool. Finally, 184 RCTs were included and evaluated methodologically, of which 97 RCTs were evaluated with reporting quality. For the methodological evaluating, 62 trials(33.70%) reported the random sequence generation; 9(4.89%) trials reported the allocation concealment; 25(13.59%) trials adopted the method of blinding; 30(16.30%) trials reported the number of patients withdrawing, dropping out and those lost to follow-up;2 trials （1.09%） reported trial registration and none of the trial reported the trial protocol; only 8(4.35%) trials reported the sample size estimation in details. For reporting quality appraising, 3 reporting items of 25 items were evaluated with high-quality,including: abstract, participants qualified criteria, and statistical methods; 4 reporting items with medium-quality, including purpose, intervention, random sequence method, and data collection of sites and locations; 9 items with low-quality reporting items including title, backgrounds, random sequence types, allocation concealment, blindness, recruitment of subjects, baseline data, harms, and funding;the rest of items were of extremely low quality(the compliance rate of reporting item<10%). On the whole, the methodological and reporting quality of RCTs published in the magazine are generally low. Further improvement in both methodological and reporting quality for RCTs of traditional Chinese medicine are warranted. It is recommended that the international standards and procedures for RCT design should be strictly followed to conduct high-quality trials. At the same time, in order to improve the reporting quality of randomized controlled trials, CONSORT standards should be adopted in the preparation of research reports and submissions. Copyright© by the Chinese Pharmaceutical Association.

Quality Aware Compression of Electrocardiogram Using Principal Component Analysis.

PubMed

Gupta, Rajarshi

2016-05-01

Electrocardiogram (ECG) compression finds wide application in various patient monitoring purposes. Quality control in ECG compression ensures reconstruction quality and its clinical acceptance for diagnostic decision making. In this paper, a quality aware compression method of single lead ECG is described using principal component analysis (PCA). After pre-processing, beat extraction and PCA decomposition, two independent quality criteria, namely, bit rate control (BRC) or error control (EC) criteria were set to select optimal principal components, eigenvectors and their quantization level to achieve desired bit rate or error measure. The selected principal components and eigenvectors were finally compressed using a modified delta and Huffman encoder. The algorithms were validated with 32 sets of MIT Arrhythmia data and 60 normal and 30 sets of diagnostic ECG data from PTB Diagnostic ECG data ptbdb, all at 1 kHz sampling. For BRC with a CR threshold of 40, an average Compression Ratio (CR), percentage root mean squared difference normalized (PRDN) and maximum absolute error (MAE) of 50.74, 16.22 and 0.243 mV respectively were obtained. For EC with an upper limit of 5 % PRDN and 0.1 mV MAE, the average CR, PRDN and MAE of 9.48, 4.13 and 0.049 mV respectively were obtained. For mitdb data 117, the reconstruction quality could be preserved up to CR of 68.96 by extending the BRC threshold. The proposed method yields better results than recently published works on quality controlled ECG compression.

Intercropping of oat and field pea in Alaska: an alternative approach to quality forage production and weed control

USDA-ARS?s Scientific Manuscript database

Intercropping of legumes with non-legumes is an ancient crop production method used to improve quality and dry matter (DM) yields of forage and grain, and to control weeds. However, there is little information regarding intercropping at high latitudes. The objectives of this field study were to eval...

Interrater Reliability in Large-Scale Assessments--Can Teachers Score National Tests Reliably without External Controls?

ERIC Educational Resources Information Center

Pantzare, Anna Lind

2015-01-01

In most large-scale assessment systems a set of rather expensive external quality controls are implemented in order to guarantee the quality of interrater reliability. This study empirically examines if teachers' ratings of national tests in mathematics can be reliable without using monitoring, training, or other methods of external quality…

The Hazardous-Drums Project: A Multiweek Laboratory Exercise for General Chemistry Involving Environmental, Quality Control, and Cost Evaluation

ERIC Educational Resources Information Center

Hayes, David; Widanski, Bozena

2013-01-01

A laboratory experiment is described that introduces students to "real-world" hazardous waste management issues chemists face. The students are required to define an analytical problem, choose a laboratory analysis method, investigate cost factors, consider quality-control issues, interpret the meaning of results, and provide management…

Quality control of murine monoclonal antibodies using isoelectric focusing affinity immunoblot analysis

NASA Technical Reports Server (NTRS)

Hamilton, Robert G.; Rodkey, L. Scott; Reimer, Charles B.

1987-01-01

The quality control of murine hybridoma secretory products has been performed using two approaches for isoelectric focusing affinity immunoblot analysis: (1) a method in which antigen-coated nitrocellulose is placed on top of an acrylamide gel containing isoelectrically focused ascites to bind the antigen specific monoclonal antibody; and (2) a method in which focused ascite proteins were passively blotted onto nitrocellulose and specific monoclonal antibodies were detected with enzyme-conjugated antigen. Analysis by both methods of batches of ascites containing antihuman IgG antibodies that were produced by six hybridomas permitted effective monitoring of immunoreactive antibodies for pI microheterogeneity.

Effects of Meteorological Data Quality on Snowpack Modeling

NASA Astrophysics Data System (ADS)

Havens, S.; Marks, D. G.; Robertson, M.; Hedrick, A. R.; Johnson, M.

2017-12-01

Detailed quality control of meteorological inputs is the most time-intensive component of running the distributed, physically-based iSnobal snow model, and the effect of data quality of the inputs on the model is unknown. The iSnobal model has been run operationally since WY2013, and is currently run in several basins in Idaho and California. The largest amount of user input during modeling is for the quality control of precipitation, temperature, relative humidity, solar radiation, wind speed and wind direction inputs. Precipitation inputs require detailed user input and are crucial to correctly model the snowpack mass. This research applies a range of quality control methods to meteorological input, from raw input with minimal cleaning, to complete user-applied quality control. The meteorological input cleaning generally falls into two categories. The first is global minimum/maximum and missing value correction that could be corrected and/or interpolated with automated processing. The second category is quality control for inputs that are not globally erroneous, yet are still unreasonable and generally indicate malfunctioning measurement equipment, such as temperature or relative humidity that remains constant, or does not correlate with daily trends observed at nearby stations. This research will determine how sensitive model outputs are to different levels of quality control and guide future operational applications.

METHOD 544. DETERMINATION OF MICROCYSTINS AND ...

EPA Pesticide Factsheets

Method 544 is an accurate and precise analytical method to determine six microcystins (including MC-LR) and nodularin in drinking water using solid phase extraction and liquid chromatography tandem mass spectrometry (SPE-LC/MS/MS). The advantage of this SPE-LC/MS/MS is its sensitivity and ability to speciate the microcystins. This method development task establishes sample preservation techniques, sample concentration and analytical procedures, aqueous and extract holding time criteria and quality control procedures. Draft Method 544 undergone a multi-laboratory verification to ensure other laboratories can implement the method and achieve the quality control measures specified in the method. It is anticipated that Method 544 may be used in UCMR 4 to collect nationwide occurrence data for selected microcystins in drinking water. The purpose of this research project is to develop an accurate and precise analytical method to concentrate and determine selected MCs and nodularin in drinking water.

A Process Analytical Technology (PAT) approach to control a new API manufacturing process: development, validation and implementation.

PubMed

Schaefer, Cédric; Clicq, David; Lecomte, Clémence; Merschaert, Alain; Norrant, Edith; Fotiadu, Frédéric

2014-03-01

Pharmaceutical companies are progressively adopting and introducing Process Analytical Technology (PAT) and Quality-by-Design (QbD) concepts promoted by the regulatory agencies, aiming the building of the quality directly into the product by combining thorough scientific understanding and quality risk management. An analytical method based on near infrared (NIR) spectroscopy was developed as a PAT tool to control on-line an API (active pharmaceutical ingredient) manufacturing crystallization step during which the API and residual solvent contents need to be precisely determined to reach the predefined seeding point. An original methodology based on the QbD principles was designed to conduct the development and validation of the NIR method and to ensure that it is fitted for its intended use. On this basis, Partial least squares (PLS) models were developed and optimized using chemometrics methods. The method was fully validated according to the ICH Q2(R1) guideline and using the accuracy profile approach. The dosing ranges were evaluated to 9.0-12.0% w/w for the API and 0.18-1.50% w/w for the residual methanol. As by nature the variability of the sampling method and the reference method are included in the variability obtained for the NIR method during the validation phase, a real-time process monitoring exercise was performed to prove its fit for purpose. The implementation of this in-process control (IPC) method on the industrial plant from the launch of the new API synthesis process will enable automatic control of the final crystallization step in order to ensure a predefined quality level of the API. In addition, several valuable benefits are expected including reduction of the process time, suppression of a rather difficult sampling and tedious off-line analyses. © 2013 Published by Elsevier B.V.

Convenient and Efficient Method for Quality Control Analysis of 18F-Fluorocholine: For a Small Scale GMP-based Radiopharmaceuticals Laboratory Set-up.

PubMed

Hassan, Hishar; Abu Bakar, Suharzelim; Halim, Khairul Najah Che A; Idris, Jaleezah; Nordin, Abdul Jalil

2016-01-01

Prostate cancer continues to be the most prevalent cancer in men in Malaysia. As time progresses, the prospect of PET imaging modality in diagnosis of prostate cancer is promising, with on-going improvement on novel tracers. Among all tracers, 18F-Fluorocholine is reported to be a reputable tracer and reliable diagnostic technique for prostate imaging. Nonetheless, only 18F-Fluorodeoxyglucose (18F-FDG) is available and used in most oncology cases in Malaysia. With a small scale GMP-based radiopharmaceuticals laboratory set-up, initial efforts have been taken to put Malaysia on 18F-Fluorocholine map. This article presents a convenient, efficient and reliable method for quality control analysis of 18F-Fluorocholine. Besides, the aim of this research work is to assist local GMP radiopharmaceuticals laboratories and local authority in Malaysia for quality control analysis of 18F-Fluorocholine guideline. In this study, prior to synthesis, quality control analysis method for 18F-Fluorocholine was developed and validated, by adapting the equipment set-up used in 18F-Fluorodeoxyglucose (18FFDG) routine production. Quality control on the 18F-Fluorocholine was performed by means of pH, radionuclidic identity, radio-high performance liquid chromatography equipped with ultraviolet, radio- thin layer chromatography, gas chromatography and filter integrity test. Post-synthesis; the pH of 18F-Fluorocholine was 6.42 ± 0.04, with half-life of 109.5 minutes (n = 12). The radiochemical purity was consistently higher than 99%, both in radio-high performance liquid chromatography equipped with ultraviolet (r-HPLC; SCX column, 0.25 M NaH2PO4: acetonitrile) and radio-thin layer chromatography method (r-TLC). The calculated relative retention time (RRT) in r-HPLC was 1.02, whereas the retention factor (Rf) in r-TLC was 0.64. Potential impurities from 18F-Fluorocholine synthesis such as ethanol, acetonitrile, dimethylethanolamine and dibromomethane were determined in gas chromatography. Using our parameters, (capillary column: DB-200, 30 m x 0.53 mm x 1 um) and oven temperature of 35°C (isothermal), all compounds were well resolved and eluted within 3 minutes. Level of ethanol and acetonitrile in 18F-Fluorocholine were detected below threshold limit; less than 5 mg/ml and 0.41 mg/ml respectively. Meanwhile, dimethylethanolamine and dibromomethane were undetectable. A convenient, efficient and reliable quality control analysis work-up procedure for 18FFluorocholine has been established and validated to comply all the release criteria. The convenient method of quality control analysis may provide a guideline to local GMP radiopharmaceutical laboratories to start producing 18F-Fluorocholine as a tracer for prostate cancer imaging.

Assessment of sound quality perception in cochlear implant users during music listening.

PubMed

Roy, Alexis T; Jiradejvong, Patpong; Carver, Courtney; Limb, Charles J

2012-04-01

Although cochlear implant (CI) users frequently report deterioration of sound quality when listening to music, few methods exist to quantify these subjective claims. 1) To design a novel research method for quantifying sound quality perception in CI users during music listening; 2) To validate this method by assessing one attribute of music perception, bass frequency perception, which is hypothesized to be relevant to overall musical sound quality perception. Limitations in bass frequency perception contribute to CI-mediated sound quality deteriorations. The proposed method will quantify this deterioration by measuring CI users' impaired ability to make sound quality discriminations among musical stimuli with variable amounts of bass frequency removal. A method commonly used in the audio industry (multiple stimulus with hidden reference and anchor [MUSHRA]) was adapted for CI users, referred to as CI-MUSHRA. CI users and normal hearing controls were presented with 7 sound quality versions of a musical segment: 5 high pass filter cutoff versions (200-, 400-, 600-, 800-, 1000-Hz) with decreasing amounts of bass information, an unaltered version ("hidden reference"), and a highly altered version (1,000-1,200 Hz band pass filter; "anchor"). Participants provided sound quality ratings between 0 (very poor) and 100 (excellent) for each version; ratings reflected differences in perceived sound quality among stimuli. CI users had greater difficulty making overall sound quality discriminations as a function of bass frequency loss than normal hearing controls, as demonstrated by a significantly weaker correlation between bass frequency content and sound quality ratings. In particular, CI users could not perceive sound quality difference among stimuli missing up to 400 Hz of bass frequency information. Bass frequency impairments contribute to sound quality deteriorations during music listening for CI users. CI-MUSHRA provided a systematic and quantitative assessment of this reduced sound quality. Although the effects of bass frequency removal were studied here, we advocate CI-MUSHRA as a user-friendly and versatile research tool to measure the effects of a wide range of acoustic manipulations on sound quality perception in CI users.

Failure analysis in the identification of synergies between cleaning monitoring methods.

PubMed

Whiteley, Greg S; Derry, Chris; Glasbey, Trevor

2015-02-01

The 4 monitoring methods used to manage the quality assurance of cleaning outcomes within health care settings are visual inspection, microbial recovery, fluorescent marker assessment, and rapid ATP bioluminometry. These methods each generate different types of information, presenting a challenge to the successful integration of monitoring results. A systematic approach to safety and quality control can be used to interrogate the known qualities of cleaning monitoring methods and provide a prospective management tool for infection control professionals. We investigated the use of failure mode and effects analysis (FMEA) for measuring failure risk arising through each cleaning monitoring method. FMEA uses existing data in a structured risk assessment tool that identifies weaknesses in products or processes. Our FMEA approach used the literature and a small experienced team to construct a series of analyses to investigate the cleaning monitoring methods in a way that minimized identified failure risks. FMEA applied to each of the cleaning monitoring methods revealed failure modes for each. The combined use of cleaning monitoring methods in sequence is preferable to their use in isolation. When these 4 cleaning monitoring methods are used in combination in a logical sequence, the failure modes noted for any 1 can be complemented by the strengths of the alternatives, thereby circumventing the risk of failure of any individual cleaning monitoring method. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Impact of dose calibrators quality control programme in Argentina

NASA Astrophysics Data System (ADS)

Furnari, J. C.; de Cabrejas, M. L.; del C. Rotta, M.; Iglicki, F. A.; Milá, M. I.; Magnavacca, C.; Dima, J. C.; Rodríguez Pasqués, R. H.

1992-02-01

The national Quality Control (QC) programme for radionuclide calibrators started 12 years ago. Accuracy and the implementation of a QC programme were evaluated over all these years at 95 nuclear medicine laboratories where dose calibrators were in use. During all that time, the Metrology Group of CNEA has distributed 137Cs sealed sources to check stability and has been performing periodic "checking rounds" and postal surveys using unknown samples (external quality control). An account of the results of both methods is presented. At present, more of 65% of the dose calibrators measure activities with an error less than 10%.

Modeling of liquid flow in surface discontinuities

NASA Astrophysics Data System (ADS)

Lobanova, I. S.; Meshcheryakov, V. A.; Kalinichenko, A. N.

2018-01-01

Polymer composite and metallic materials have found wide application in various industries such as aviation, rocket, car manufacturing, ship manufacturing, etc. Many design elements need permanent quality control. Ensuring high quality and reliability of products is impossible without effective nondestructive testing methods. One of these methods is penetrant testing using penetrating substances based on liquid penetration into defect cavities. In this paper, we propose a model of liquid flow to determine the rates of filling the defect cavities with various materials and, based on this, to choose optimal control modes.

Interactions between butterfly-shaped pulses in the inhomogeneous media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Wen-Jun; Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190; Huang, Long-Gang

2014-10-15

Pulse interactions affect pulse qualities during the propagation. Interactions between butterfly-shaped pulses are investigated to improve pulse qualities in the inhomogeneous media. In order to describe the interactions between butterfly-shaped pulses, analytic two-soliton solutions are derived. Based on those solutions, influences of corresponding parameters on pulse interactions are discussed. Methods to control the pulse interactions are suggested. - Highlights: • Interactions between butterfly-shaped pulses are investigated. • Methods to control the pulse interactions are suggested. • Analytic two-soliton solutions for butterfly-shaped pulses are derived.

The importance of quality control in validating concentrations of contaminants of emerging concern in source and treated drinking water samples.

PubMed

Batt, Angela L; Furlong, Edward T; Mash, Heath E; Glassmeyer, Susan T; Kolpin, Dana W

2017-02-01

A national-scale survey of 247 contaminants of emerging concern (CECs), including organic and inorganic chemical compounds, and microbial contaminants, was conducted in source and treated drinking water samples from 25 treatment plants across the United States. Multiple methods were used to determine these CECs, including six analytical methods to measure 174 pharmaceuticals, personal care products, and pesticides. A three-component quality assurance/quality control (QA/QC) program was designed for the subset of 174 CECs which allowed us to assess and compare performances of the methods used. The three components included: 1) a common field QA/QC protocol and sample design, 2) individual investigator-developed method-specific QA/QC protocols, and 3) a suite of 46 method comparison analytes that were determined in two or more analytical methods. Overall method performance for the 174 organic chemical CECs was assessed by comparing spiked recoveries in reagent, source, and treated water over a two-year period. In addition to the 247 CECs reported in the larger drinking water study, another 48 pharmaceutical compounds measured did not consistently meet predetermined quality standards. Methodologies that did not seem suitable for these analytes are overviewed. The need to exclude analytes based on method performance demonstrates the importance of additional QA/QC protocols. Published by Elsevier B.V.

The Ronnie Gardiner Rhythm and Music Method - a feasibility study in Parkinson's disease.

PubMed

Pohl, Petra; Dizdar, Nil; Hallert, Eva

2013-01-01

To assess the feasibility of the novel intervention, Ronnie Gardiner Rhythm and Music (RGRM™) Method compared to a control group for patients with Parkinson's disease (PD). Eighteen patients, mean age 68, participating in a disability study within a neurological rehabilitation centre, were randomly allocated to intervention group (n = 12) or control group (n = 6). Feasibility was assessed by comparing effects of the intervention on clinical outcome measures (primary outcome: mobility as assessed by two-dimensional motion analysis, secondary outcomes: mobility, cognition, quality of life, adherence, adverse events and eligibility). Univariable analyses showed no significant differences between groups following intervention. However, analyses suggested that patients in the intervention group improved more on mobility (p = 0.006), cognition and quality of life than patients in the control group. There were no adverse events and a high level of adherence to therapy was observed. In this disability study, the use of the RGRM™ Method showed promising results in the intervention group and the adherence level was high. Our results suggest that most assessments chosen are eligible to use in a larger randomized controlled study for patients with PD. The RGRM™ Method appeared to be a useful and safe method that showed promising results in both motor and cognitive functions as well as quality of life in patients with moderate PD. The RGRM™ Method can be used by physiotherapists, occupational, speech and music therapists in neurological rehabilitation. Most measurements were feasible except for Timed-Up-and-Go.

A Review of Auditing Methods Applied to the Content of Controlled Biomedical Terminologies

PubMed Central

Zhu, Xinxin; Fan, Jung-Wei; Baorto, David M.; Weng, Chunhua; Cimino, James J.

2012-01-01

Although controlled biomedical terminologies have been with us for centuries, it is only in the last couple of decades that close attention has been paid to the quality of these terminologies. The result of this attention has been the development of auditing methods that apply formal methods to assessing whether terminologies are complete and accurate. We have performed an extensive literature review to identify published descriptions of these methods and have created a framework for characterizing them. The framework considers manual, systematic and heuristic methods that use knowledge (within or external to the terminology) to measure quality factors of different aspects of the terminology content (terms, semantic classification, and semantic relationships). The quality factors examined included concept orientation, consistency, non-redundancy, soundness and comprehensive coverage. We reviewed 130 studies that were retrieved based on keyword search on publications in PubMed, and present our assessment of how they fit into our framework. We also identify which terminologies have been audited with the methods and provide examples to illustrate each part of the framework. PMID:19285571

Field Methods and Quality-Assurance Plan for Quality-of-Water Activities, U.S. Geological Survey, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Knobel, LeRoy L.; Tucker, Betty J.; Rousseau, Joseph P.

2008-01-01

Water-quality activities conducted by the staff of the U.S. Geological Survey (USGS) Idaho National Laboratory (INL) Project Office coincide with the USGS mission of appraising the quantity and quality of the Nation's water resources. The activities are conducted in cooperation with the U.S. Department of Energy's (DOE) Idaho Operations Office. Results of the water-quality investigations are presented in various USGS publications or in refereed scientific journals. The results of the studies are highly regarded, and they are used with confidence by researchers, regulatory and managerial agencies, and interested civic groups. In its broadest sense, quality assurance refers to doing the job right the first time. It includes the functions of planning for products, review and acceptance of the products, and an audit designed to evaluate the system that produces the products. Quality control and quality assurance differ in that quality control ensures that things are done correctly given the 'state-of-the-art' technology, and quality assurance ensures that quality control is maintained within specified limits.

Precipitation data in a mountainous catchment in Honduras: quality assessment and spatiotemporal characteristics

NASA Astrophysics Data System (ADS)

Westerberg, I.; Walther, A.; Guerrero, J.-L.; Coello, Z.; Halldin, S.; Xu, C.-Y.; Chen, D.; Lundin, L.-C.

2010-08-01

An accurate description of temporal and spatial precipitation variability in Central America is important for local farming, water supply and flood management. Data quality problems and lack of consistent precipitation data impede hydrometeorological analysis in the 7,500 km2 Choluteca River basin in central Honduras, encompassing the capital Tegucigalpa. We used precipitation data from 60 daily and 13 monthly stations in 1913-2006 from five local authorities and NOAA's Global Historical Climatology Network. Quality control routines were developed to tackle the specific data quality problems. The quality-controlled data were characterised spatially and temporally, and compared with regional and larger-scale studies. Two gap-filling methods for daily data and three interpolation methods for monthly and mean annual precipitation were compared. The coefficient-of-correlation-weighting method provided the best results for gap-filling and the universal kriging method for spatial interpolation. In-homogeneity in the time series was the main quality problem, and 22% of the daily precipitation data were too poor to be used. Spatial autocorrelation for monthly precipitation was low during the dry season, and correlation increased markedly when data were temporally aggregated from a daily time scale to 4-5 days. The analysis manifested the high spatial and temporal variability caused by the diverse precipitation-generating mechanisms and the need for an improved monitoring network.

High cortisol levels are associated with low quality food choice in type 2 diabetes.

PubMed

Duong, Michelle; Cohen, Jessica I; Convit, Antonio

2012-02-01

Hypothalamic-pituitary-adrenal (HPA) axis control may be impaired in type 2 diabetes (T2DM). Glucocorticoids increase consumption of low quality foods high in calories, sugar, and fat. We explored the relationship between cortisol levels, poor blood glucose control, and food quality choice in T2DM. Twenty-seven healthy controls were age-, gender- and education-matched to 27 T2DM participants. Standard clinical blood tests and cortisol values were measured from fasting blood samples. Participants recorded all consumed food and drink items in a consecutive 3-day food diary. Diaries were analyzed for "high quality" and "low quality" foods using a standardized method with high reliability (0.97 and 0.86, respectively). Controlling for education, body mass index (BMI) and hemoglobin A1C (HbA1C), log-transformed cortisol (LogC) predicted the percent of low quality foods (R (2) = 0.092, β = 0.360, P < 0.05), but not the percent of high quality foods chosen. Controlling for education, BMI, and LogC, HbA1C significantly predicted both the percent of low quality foods (ΔR (2) = 0.079, β = 0.348, P = 0.024) and high quality foods chosen (ΔR (2) = 0.085, β = -0.362, P = 0.022). The relationship between HbA1C and low quality food choice may be mediated by cortisol, controlling for BMI and education (P < 0.01). HbA1C displayed both an indirect (cortisol-mediated) effect (P < 0.05) and direct effect on low quality food choice (P < 0.05). The relationship between HbA1C and low quality food choice may be partially mediated by cortisol. Poor blood glucose control may cause HPA axis disruption, increased consumption of low quality foods.

Detection of human enteric viruses in stream water with RT-PCR and cell culture.

USGS Publications Warehouse

Denis-Mize, K.; Fout, G.S.; Dahling, D.R.; Francy, D.S.

2004-01-01

A multiplex RT-PCR method was used to measure virus occurrence at five stream water sites that span a range of hydroclimatic, water-quality, and land-use characteristics. The performance of the molecular method was evaluated in comparison with traditional cell culture and Escherichia coli membrane filtration assays. The study incorporated multiple quality controls and included a control for virus recovery during the sampling procedure as well as controls to detect potentially false-negative and false-positive data. Poliovirus recovery ranged from 16 to 65% and was variable, even in samples collected within the same stream. All five sites were positive for viruses by both molecular and cell culture-based virus assays. Enteroviruses, reoviruses, rotaviruses, and hepatitis A viruses were detected, but the use of the quality controls proved critical for interpretation of the molecular data. All sites showed evidence of faecal contamination, and culturable viruses were detected in four samples that would have met the US Environmental Protection Agency's recommended E. coli guideline for safe recreational water.

[Quality control of oral anticoagulant therapy in Primary Care in Madrid City, Spain: CHRONOS-TAO study].

PubMed

Alonso Roca, Rafael; Figueroa Guerrero, Carmen Arlene; Mainar de Paz, Victoria; Arribas García, M Paz; Sánchez Perruca, Luis; Rodríguez Barrientos, Ricardo; Casado López, Mariano; Pedraza Flechas, Ana M

2015-09-07

To determine quality control of patients with oral anticoagulant treatment recruited in Primary Care (PC) using the Rosendaal method to estimate time in therapeutic range (TTR) and comparing it with fraction of international normalized ratio (INR) in range and cross-sectional analysis (last INR registred). A retrospective observational study based on electronic medical record in routine clinical practice. PC centers (262) in Madrid. We included all patients with acenocumarol treatment, with an INR therapeutic range established between 2 and 3. We excluded patients with valvular pathology and disrupted clinical follow up in PC (<3 INR determinations in the studied period, a period of>90 days or ≥ 3 periods of>60 days between 2 determinations). The final population was 49,312 patients. The variables considered were all INR values and their respective dates. TTR was calculated by the 3 methods above mentioned. We considered "therapeutic range" INR between 2-3 and "adjusted range" INR between 1.8-3.2. Optimal control for each patient was considered TTR>60%. By using Rosendaal method, TTR was 66.8% (81.7% adjusted), with a percentage of total INR in range was 58.8% (66.5% adjusted), and, with the cross-sectional analysis, it was 70.5% (76.8% adjusted). Mean TTR was 65% (standard deviation 20.3), and the percentage of patients with TTR>60% was 63.3% (88.1% adjusted). The quality control of patients with oral anticoagulants in PC in Madrid is acceptable, similar or higher to other studies and pivotal trials of new anticoagulants. Compared to the Rosendaal method, total fraction of INR underestimates quality control, and cross-sectional analysis slightly overestimates it. Copyright © 2014 Elsevier España, S.L.U. All rights reserved.

46 CFR 160.132-9 - Preapproval review.

Code of Federal Regulations, 2014 CFR

2014-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.132-19 and 160.132-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR subpart 159.010. (d) Plan quality. All...

46 CFR 160.132-9 - Preapproval review.

Code of Federal Regulations, 2012 CFR

2012-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.132-19 and 160.132-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR subpart 159.010. (d) Plan quality. All...

46 CFR 160.132-9 - Preapproval review.

Code of Federal Regulations, 2013 CFR

2013-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.132-19 and 160.132-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR subpart 159.010. (d) Plan quality. All...

Measuring and improving the quality of postoperative epidural analgesia for major abdominal surgery using statistical process control charts.

PubMed

Duncan, Fiona; Haigh, Carol

2013-10-01

To explore and improve the quality of continuous epidural analgesia for pain relief using Statistical Process Control tools. Measuring the quality of pain management interventions is complex. Intermittent audits do not accurately capture the results of quality improvement initiatives. The failure rate for one intervention, epidural analgesia, is approximately 30% in everyday practice, so it is an important area for improvement. Continuous measurement and analysis are required to understand the multiple factors involved in providing effective pain relief. Process control and quality improvement Routine prospectively acquired data collection started in 2006. Patients were asked about their pain and side effects of treatment. Statistical Process Control methods were applied for continuous data analysis. A multidisciplinary group worked together to identify reasons for variation in the data and instigated ideas for improvement. The key measure for improvement was a reduction in the percentage of patients with an epidural in severe pain. The baseline control charts illustrated the recorded variation in the rate of several processes and outcomes for 293 surgical patients. The mean visual analogue pain score (VNRS) was four. There was no special cause variation when data were stratified by surgeons, clinical area or patients who had experienced pain before surgery. Fifty-seven per cent of patients were hypotensive on the first day after surgery. We were able to demonstrate a significant improvement in the failure rate of epidurals as the project continued with quality improvement interventions. Statistical Process Control is a useful tool for measuring and improving the quality of pain management. The applications of Statistical Process Control methods offer the potential to learn more about the process of change and outcomes in an Acute Pain Service both locally and nationally. We have been able to develop measures for improvement and benchmarking in routine care that has led to the establishment of a national pain registry. © 2013 Blackwell Publishing Ltd.

Chemistry and quality of Hibiscus (Hibiscus sabdariffa) for developing the natural-product industry in Senegal.

PubMed

Juliani, H R; Welch, C R; Wu, Q; Diouf, B; Malainy, D; Simon, J E

2009-03-01

The objectives of this study were to assess and improve the quality of the hibiscus calyces from Senegal over 2 production seasons (2004 to 2005), to develop and adapt new procedures for the determination of hibiscus anthocyanins and analysis of the 2 major ones, delphinidin-3-sambubioside and cyanidin-3-sambubioside. The foreign matter, total ashes, and acid insoluble ashes showed that the calyces harvested in 2005 were produced following hygienic practices, while the color assessment of the calyces and analysis of hibiscus active principles also showed higher amounts of anthocyanins in 2005. A protocol to measure anthocyanins by pH-differential UV-Vis spectrophotometry was adapted to measure the hibiscus anthocyanins from a water extract. The spectrophotometric method for quantitation of total anthocyanins showed a close correlation (r(2)= 0.82) when compared with the HPLC method, suggesting the use of the colorimetric method in quality control programs as an affordable alternative method to assess anthocyanin content in hibiscus. New and raised standards for the cleanliness and active principle content in hibiscus are also proposed. This study demonstrated that the implementation of a quality control program and the application of agricultural good practices in the production and processing of hibiscus calyces can lead to higher quality natural plant products.

Ultra-high performance liquid chromatography coupled with quadrupole/time of flight mass spectrometry based chemical profiling approach for the holistic quality control of complex Kang-Jing formula preparations.

PubMed

Yang, Xiao-Huan; Cheng, Xiao-Lan; Qin, Bing; Cai, Zhuo-Ya; Cai, Xiong; Liu, Shao; Wang, Qi; Qin, Yong

2016-05-30

The Kang-Jing (KJ) formula is a compound preparation made from 12 kinds of herbs. So far, four different methods (M1-M4) have been documented for KJ preparation, but the influence of preparation methods on the holistic quality of KJ have remained unknown. In this study, a strategy was proposed to investigate the influence of different preparation methods on the holistic quality of KJ using ultra-high performance liquid chromatography coupled with quadrupole/time of flight mass spectrometry (UHPLC-QTOF-MS/MS) based chemical profiling. A total of 101 compounds mainly belonging to flavonoids, tanshinones, monoterpene glycosides, triterpenoid saponins, alkaloids, phenolic acids and volatile oils, were identified. Among these compounds, glaucine was detected only in M3/M4 samples, while two dehydrocorydaline isomers merely detected in M2/M3/M4 samples. Tetrahydrocolumbamine, ethylic lithospermic acid, salvianolic acid E and rosmarimic acid were only detected in M1/M3/M4 samples. In the subsequent quantitative analysis, 12 major compounds were determined by UHPLC-MS/MS. The proposed method was validated with respect to linearity, accuracy, precision and recovery. It was found that the contents of marker compounds varied significantly in samples prepared by different methods. These results demonstrated that preparation method does significantly affect the holistic quality of KJ. UHPLC-QTOF-MS/MS based chemical profiling approach is efficient and reliable for comprehensive quality evaluation of KJ. Collectively, this study provide the chemical evidence for revealing the material basis of KJ, and establish a simple and accurate chemical profiling method for its quality control. Copyright © 2016 Elsevier B.V. All rights reserved.

Bridging the Gap Between Validation and Implementation of Non-Animal Veterinary Vaccine Potency Testing Methods

PubMed Central

Dozier, Samantha; Brown, Jeffrey; Currie, Alistair

2011-01-01

Simple Summary Many vaccines are tested for quality in experiments that require the use of large numbers of animals in procedures that often cause significant pain and distress. Newer technologies have fostered the development of vaccine quality control tests that reduce or eliminate the use of animals, but the availability of these newer methods has not guaranteed their acceptance by regulators or use by manufacturers. We discuss a strategic approach that has been used to assess and ultimately increase the use of non-animal vaccine quality tests in the U.S. and U.K. Abstract In recent years, technologically advanced high-throughput techniques have been developed that replace, reduce or refine animal use in vaccine quality control tests. Following validation, these tests are slowly being accepted for use by international regulatory authorities. Because regulatory acceptance itself has not guaranteed that approved humane methods are adopted by manufacturers, various organizations have sought to foster the preferential use of validated non-animal methods by interfacing with industry and regulatory authorities. After noticing this gap between regulation and uptake by industry, we began developing a paradigm that seeks to narrow the gap and quicken implementation of new replacement, refinement or reduction guidance. A systematic analysis of our experience in promoting the transparent implementation of validated non-animal vaccine potency assays has led to the refinement of our paradigmatic process, presented here, by which interested parties can assess the local regulatory acceptance of methods that reduce animal use and integrate them into quality control testing protocols, or ensure the elimination of peripheral barriers to their use, particularly for potency and other tests carried out on production batches. PMID:26486625

Detention basin alternative outlet design study.

DOT National Transportation Integrated Search

2016-10-01

This study examines the outlets structures CDOT has historically employed to drain water quality treatment detention basins and flood control basins, presents two new methods of metering the water quality capture volume (WQCV), namely 1) the Elliptic...

Evaluating the Good Ontology Design Guideline (GoodOD) with the Ontology Quality Requirements and Evaluation Method and Metrics (OQuaRE)

PubMed Central

Duque-Ramos, Astrid; Boeker, Martin; Jansen, Ludger; Schulz, Stefan; Iniesta, Miguela; Fernández-Breis, Jesualdo Tomás

2014-01-01

Objective To (1) evaluate the GoodOD guideline for ontology development by applying the OQuaRE evaluation method and metrics to the ontology artefacts that were produced by students in a randomized controlled trial, and (2) informally compare the OQuaRE evaluation method with gold standard and competency questions based evaluation methods, respectively. Background In the last decades many methods for ontology construction and ontology evaluation have been proposed. However, none of them has become a standard and there is no empirical evidence of comparative evaluation of such methods. This paper brings together GoodOD and OQuaRE. GoodOD is a guideline for developing robust ontologies. It was previously evaluated in a randomized controlled trial employing metrics based on gold standard ontologies and competency questions as outcome parameters. OQuaRE is a method for ontology quality evaluation which adapts the SQuaRE standard for software product quality to ontologies and has been successfully used for evaluating the quality of ontologies. Methods In this paper, we evaluate the effect of training in ontology construction based on the GoodOD guideline within the OQuaRE quality evaluation framework and compare the results with those obtained for the previous studies based on the same data. Results Our results show a significant effect of the GoodOD training over developed ontologies by topics: (a) a highly significant effect was detected in three topics from the analysis of the ontologies of untrained and trained students; (b) both positive and negative training effects with respect to the gold standard were found for five topics. Conclusion The GoodOD guideline had a significant effect over the quality of the ontologies developed. Our results show that GoodOD ontologies can be effectively evaluated using OQuaRE and that OQuaRE is able to provide additional useful information about the quality of the GoodOD ontologies. PMID:25148262

An express method for optimally tuning an analog controller with respect to integral quality criteria

NASA Astrophysics Data System (ADS)

Golinko, I. M.; Kovrigo, Yu. M.; Kubrak, A. I.

2014-03-01

An express method for optimally tuning analog PI and PID controllers is considered. An integral quality criterion with minimizing the control output is proposed for optimizing control systems. The suggested criterion differs from existing ones in that the control output applied to the technological process is taken into account in a correct manner, due to which it becomes possible to maximally reduce the expenditure of material and/or energy resources in performing control of industrial equipment sets. With control organized in such manner, smaller wear and longer service life of control devices are achieved. A unimodal nature of the proposed criterion for optimally tuning a controller is numerically demonstrated using the methods of optimization theory. A functional interrelation between the optimal controller parameters and dynamic properties of a controlled plant is numerically determined for a single-loop control system. The results obtained from simulation of transients in a control system carried out using the proposed and existing functional dependences are compared with each other. The proposed calculation formulas differ from the existing ones by a simple structure and highly accurate search for the optimal controller tuning parameters. The obtained calculation formulas are recommended for being used by specialists in automation for design and optimization of control systems.

Simultaneous Determination of Ten Constituents in Chaiqin Qingning Capsule by High-performance Liquid Chromatography Coupled with Triple-quadrupole Mass Spectrometry.

PubMed

Li, Ting Yu; Huo, Xiao Kui; Zheng, Lu; Wang, Chao; Cong, Hai Jian; Xiang, Ting; Zhang, Lin; Zhang, Bao Jing; Huang, Shan Shan; Wu, Bin; Li, Xin Yu

2017-01-01

Chaiqin Qingning Capsule (CQQNC) was a prescription of Traditional Chinese Medicine with the effects of clearing away heat and removing toxin, harmonizing the exterior and interior, it was widely used in Asian, for example, China and Japan, different batches of the raws materials and different processing time may be the vital factor which raised a challenge to control the quality of the CQQNC. In this experiment, a high-performance liquid chromatography-mass spectrometry/MS (HPLC-MS/MS) method was developed to simultaneously determine ten bioactive components for the quality control of CQQNC. Chromatographic separation was achieved using an XBridge BEH C18 column (150 mm × 4.6 mm, 2.5 μm) with a mobile phase composed of 10 mm aqueous ammonium acetate and acetonitrile using a gradient elution in 20 min. This study was conducted by multiple reaction monitoring mode through electrospray ionization resource with a negative ionization mode. The established method was validated with good performance of precision, accuracy, stability, and reproducibility and was utilized to simultaneously quantify ten constituents of CQQNC obtained from seven different batches. It is the first time to report the rapid and simultaneous analysis of the ten compounds in CQQNC by HPLC-MS/MS and apply to determine 10 constituents in 7 batches of CQQNC bought from drug store in china. This method could be considered as good quality criteria to control the quality of CQQNC. In this paper, a simple, specific, and rapid high-performance liquid chromatogram coupled with triple-quadrupole mass spectrometry method for simultaneous quantification of ten constituents in Chaiqin Qingning Capsule has been developed for the first time. This method could be considered as good quality criteria to control the quality of CQQNC. Abbreviations used: CHM: Chinese herbal medicine; TCM: Traditional Chinese Medicine; CQQNC: Triple-quadrupole mass spectrometry Chaiqin Qingning Capsules; HPLC-MS/MS: High liquid chromatography equipped with tandem mass spectrometry; ESI: Electrospray ionization; DP: Declustering potential; CE: Collision energy; RSD: Relative standard deviation; LOD: Limit of detection; LOQ: Limit of quantity.

Point focusing using loudspeaker arrays from the perspective of optimal beamforming.

PubMed

Bai, Mingsian R; Hsieh, Yu-Hao

2015-06-01

Sound focusing is to create a concentrated acoustic field in the region surrounded by a loudspeaker array. This problem was tackled in the previous research via the Helmholtz integral approach, brightness control, acoustic contrast control, etc. In this paper, the same problem was revisited from the perspective of beamforming. A source array model is reformulated in terms of the steering matrix between the source and the field points, which lends itself to the use of beamforming algorithms such as minimum variance distortionless response (MVDR) and linearly constrained minimum variance (LCMV) originally intended for sensor arrays. The beamforming methods are compared with the conventional methods in terms of beam pattern, directional index, and control effort. Objective tests are conducted to assess the audio quality by using perceptual evaluation of audio quality (PEAQ). Experiments of produced sound field and listening tests are conducted in a listening room, with results processed using analysis of variance and regression analysis. In contrast to the conventional energy-based methods, the results have shown that the proposed methods are phase-sensitive in light of the distortionless constraint in formulating the array filters, which helps enhance audio quality and focusing performance.

49 CFR 40.235 - What are the requirements for proper use and care of ASDs?

Code of Federal Regulations, 2014 CFR

2014-10-01

... ASD on the CPL. Your QAP must specify the methods used for quality control checks, temperatures at which the ASD must be stored and used, the shelf life of the device, and environmental conditions (e.g... the specified quality control checks or that has passed its expiration date. (e) As an employer, with...

49 CFR 40.235 - What are the requirements for proper use and care of ASDs?

Code of Federal Regulations, 2012 CFR

2012-10-01

... ASD on the CPL. Your QAP must specify the methods used for quality control checks, temperatures at which the ASD must be stored and used, the shelf life of the device, and environmental conditions (e.g... the specified quality control checks or that has passed its expiration date. (e) As an employer, with...

49 CFR 40.235 - What are the requirements for proper use and care of ASDs?

Code of Federal Regulations, 2011 CFR

2011-10-01

... ASD on the CPL. Your QAP must specify the methods used for quality control checks, temperatures at which the ASD must be stored and used, the shelf life of the device, and environmental conditions (e.g... the specified quality control checks or that has passed its expiration date. (e) As an employer, with...

49 CFR 40.235 - What are the requirements for proper use and care of ASDs?

Code of Federal Regulations, 2010 CFR

2010-10-01

... ASD on the CPL. Your QAP must specify the methods used for quality control checks, temperatures at which the ASD must be stored and used, the shelf life of the device, and environmental conditions (e.g... the specified quality control checks or that has passed its expiration date. (e) As an employer, with...

49 CFR 40.235 - What are the requirements for proper use and care of ASDs?

Code of Federal Regulations, 2013 CFR

2013-10-01

... ASD on the CPL. Your QAP must specify the methods used for quality control checks, temperatures at which the ASD must be stored and used, the shelf life of the device, and environmental conditions (e.g... the specified quality control checks or that has passed its expiration date. (e) As an employer, with...

Real Time Quality Control Methods for Cued EMI Data Collection

DTIC Science & Technology

2016-03-14

contents be construed as reflecting the official policy or position of the Department of Defense. Reference herein to any specific commercial product...This project evaluated the effectiveness of in-field quality control (QC) procedures during cued electromagnetic induction (EMI) data collection. The...electromagnetic induction ESTCP Environmental Security Technology Certification Program hr hour ISO Industry Standard Object IVS Instrument

The Quality of Care under a Managed-Care Program for Dual Eligibles

ERIC Educational Resources Information Center

Kane, Robert L.; Homyak, Patricia; Bershadsky, Boris; Lum, Terry; Flood, Shannon; Zhang, Hui

2005-01-01

Purpose: Our objective in this study was to compare the quality of care provided under the Minnesota Senior Health Options (MSHO), a special program designed to serve dually eligible older persons, to care provided to controls who received fee-for-service Medicare and Medicaid managed care. Design and Methods: Two control groups were used; one was…

Likelihood of achieving air quality targets under model uncertainties.

PubMed

Digar, Antara; Cohan, Daniel S; Cox, Dennis D; Kim, Byeong-Uk; Boylan, James W

2011-01-01

Regulatory attainment demonstrations in the United States typically apply a bright-line test to predict whether a control strategy is sufficient to attain an air quality standard. Photochemical models are the best tools available to project future pollutant levels and are a critical part of regulatory attainment demonstrations. However, because photochemical models are uncertain and future meteorology is unknowable, future pollutant levels cannot be predicted perfectly and attainment cannot be guaranteed. This paper introduces a computationally efficient methodology for estimating the likelihood that an emission control strategy will achieve an air quality objective in light of uncertainties in photochemical model input parameters (e.g., uncertain emission and reaction rates, deposition velocities, and boundary conditions). The method incorporates Monte Carlo simulations of a reduced form model representing pollutant-precursor response under parametric uncertainty to probabilistically predict the improvement in air quality due to emission control. The method is applied to recent 8-h ozone attainment modeling for Atlanta, Georgia, to assess the likelihood that additional controls would achieve fixed (well-defined) or flexible (due to meteorological variability and uncertain emission trends) targets of air pollution reduction. The results show that in certain instances ranking of the predicted effectiveness of control strategies may differ between probabilistic and deterministic analyses.

Empirical evaluation of humpback whale telomere length estimates; quality control and factors causing variability in the singleplex and multiplex qPCR methods.

PubMed

Olsen, Morten Tange; Bérubé, Martine; Robbins, Jooke; Palsbøll, Per J

2012-09-06

Telomeres, the protective cap of chromosomes, have emerged as powerful markers of biological age and life history in model and non-model species. The qPCR method for telomere length estimation is one of the most common methods for telomere length estimation, but has received recent critique for being too error-prone and yielding unreliable results. This critique coincides with an increasing awareness of the potentials and limitations of the qPCR technique in general and the proposal of a general set of guidelines (MIQE) for standardization of experimental, analytical, and reporting steps of qPCR. In order to evaluate the utility of the qPCR method for telomere length estimation in non-model species, we carried out four different qPCR assays directed at humpback whale telomeres, and subsequently performed a rigorous quality control to evaluate the performance of each assay. Performance differed substantially among assays and only one assay was found useful for telomere length estimation in humpback whales. The most notable factors causing these inter-assay differences were primer design and choice of using singleplex or multiplex assays. Inferred amplification efficiencies differed by up to 40% depending on assay and quantification method, however this variation only affected telomere length estimates in the worst performing assays. Our results suggest that seemingly well performing qPCR assays may contain biases that will only be detected by extensive quality control. Moreover, we show that the qPCR method for telomere length estimation can be highly precise and accurate, and thus suitable for telomere measurement in non-model species, if effort is devoted to optimization at all experimental and analytical steps. We conclude by highlighting a set of quality controls which may serve for further standardization of the qPCR method for telomere length estimation, and discuss some of the factors that may cause variation in qPCR experiments.

Empirical evaluation of humpback whale telomere length estimates; quality control and factors causing variability in the singleplex and multiplex qPCR methods

PubMed Central

2012-01-01

Background Telomeres, the protective cap of chromosomes, have emerged as powerful markers of biological age and life history in model and non-model species. The qPCR method for telomere length estimation is one of the most common methods for telomere length estimation, but has received recent critique for being too error-prone and yielding unreliable results. This critique coincides with an increasing awareness of the potentials and limitations of the qPCR technique in general and the proposal of a general set of guidelines (MIQE) for standardization of experimental, analytical, and reporting steps of qPCR. In order to evaluate the utility of the qPCR method for telomere length estimation in non-model species, we carried out four different qPCR assays directed at humpback whale telomeres, and subsequently performed a rigorous quality control to evaluate the performance of each assay. Results Performance differed substantially among assays and only one assay was found useful for telomere length estimation in humpback whales. The most notable factors causing these inter-assay differences were primer design and choice of using singleplex or multiplex assays. Inferred amplification efficiencies differed by up to 40% depending on assay and quantification method, however this variation only affected telomere length estimates in the worst performing assays. Conclusion Our results suggest that seemingly well performing qPCR assays may contain biases that will only be detected by extensive quality control. Moreover, we show that the qPCR method for telomere length estimation can be highly precise and accurate, and thus suitable for telomere measurement in non-model species, if effort is devoted to optimization at all experimental and analytical steps. We conclude by highlighting a set of quality controls which may serve for further standardization of the qPCR method for telomere length estimation, and discuss some of the factors that may cause variation in qPCR experiments. PMID:22954451

[Report quality of randomized controlled trials of moxibustion for knee osteoarthritis based on CONSORT and STRICTOM].

PubMed

Xiong, Jun; Zhu, Daocheng; Chen, Rixin; Ye, Wenguo

2015-08-01

The report quality of randomized controlled trials (RCTs) of moxibustion for knee osteoarthritis (KOA) in China was evaluated by Consolidated Standards for Reporting of Trials (CONSORT) and Standards for Reporting Interventions in Controlled Trials of Moxibustion (STRICTOM). Computer and manual retrieval was used. Four databases of China National Knowledge Infrastructure (CNKD, China Biomedicine (CBM), VIP and WNFANG were searched in combination with manual retrieval for relevant journals to screen the literature that: met the inclusive criteria, and CONSORT and STRICTOM were used to assess the report quality. A total of 52 RCTs were included. It was found that unclear description of random methods, low use of blind methods, no allocation concealment, no sample size calculation, no intention-to-treat analysis,inadequate report of moxibustion details and no mention of practitioners background existed in the majority of the RCTs. Although the quality of RCTs of moxibustion for KOA was generally low, reducing the reliability and homogeneous comparability of the reports ,the quality of heat-sensitive moxibustion RCTs was high. It was believed that in order to improve the reliability and quality of RCTs of moxibustion, CONSORT and STRICTOM should be introduced into the RCT design of moxibustion and be strictly performed.

Screening for the anti-inflammation quality markers of Xiaojin Pills based on HPLC-MS/MS method, COX-2 inhibition test and protein interaction network.

PubMed

Xiong, Xi; He, Ya-Nan; Feng, Bi; Pan, Yuan; Zhang, Hai-Zhu; Ke, Xiu-Mei; Zhang, Yi; Yang, Ming; Han, Li; Zhang, Ding-Kun

2018-05-10

Nowadays, breast disorders seriously affect women's health in an increasing number. In China, Xiaojin Pills are commonly used in the treatment of breast diseases. Doctors have concluded that the combined use of Xiaojin Pills with conventional therapy can significantly improve the efficacy with fewer side effects. However, the prescription of Xiaojin Pills is complicated and their quality control methods cannot completely ensure the quality of Xiaojin Pills. On the basis of its mechanism, our study combined chemical evaluation and biological evaluation to identify the anti-inflammatory markers of Xiaojin Pills. In this manuscript, 13 compounds in Xiaojin Pills were quantified. At the same time, the cyclooxygenase-2 inhibition rates of different Xiaojin Pills were measured and the possible markers were screened by spectrum-effect relationship. Further, anti-inflammatory activities of markers were verified and protein interaction network was analyzed, identifying the components of Protocatechuate, Beta-Boswellic acid and Levistilide A as the anti-inflammatory quality markers of Xiaojin Pills. We hope our studies can provide a scientific theoretical basis for accurately quality control of Xiaojin Pills and reasonable suggestions for pharmaceutical companies and new ideas for the quality control of other medicines.

Application of advanced data collection and quality assurance methods in open prospective study - a case study of PONS project.

PubMed

Wawrzyniak, Zbigniew M; Paczesny, Daniel; Mańczuk, Marta; Zatoński, Witold A

2011-01-01

Large-scale epidemiologic studies can assess health indicators differentiating social groups and important health outcomes of the incidence and mortality of cancer, cardiovascular disease, and others, to establish a solid knowledgebase for the prevention management of premature morbidity and mortality causes. This study presents new advanced methods of data collection and data management systems with current data quality control and security to ensure high quality data assessment of health indicators in the large epidemiologic PONS study (The Polish-Norwegian Study). The material for experiment is the data management design of the large-scale population study in Poland (PONS) and the managed processes are applied into establishing a high quality and solid knowledge. The functional requirements of the PONS study data collection, supported by the advanced IT web-based methods, resulted in medical data of a high quality, data security, with quality data assessment, control process and evolution monitoring are fulfilled and shared by the IT system. Data from disparate and deployed sources of information are integrated into databases via software interfaces, and archived by a multi task secure server. The practical and implemented solution of modern advanced database technologies and remote software/hardware structure successfully supports the research of the big PONS study project. Development and implementation of follow-up control of the consistency and quality of data analysis and the processes of the PONS sub-databases have excellent measurement properties of data consistency of more than 99%. The project itself, by tailored hardware/software application, shows the positive impact of Quality Assurance (QA) on the quality of outcomes analysis results, effective data management within a shorter time. This efficiency ensures the quality of the epidemiological data and indicators of health by the elimination of common errors of research questionnaires and medical measurements.

Advanced control technology and airworthiness flying qualities requirements

NASA Technical Reports Server (NTRS)

Snyder, C. T.

1976-01-01

Flying quality requirements are specified in terms of the complete pilot-airframe-systems loop, the task, and the environment. Results from a study of flying qualities are reported. A review of the treatment of failure cases in various flying quality requirements is presented along with a description of the methods used and relevant lessons learned from recent Autoland certification programs.

Long-Term Quality Control Program Plan for Cord Blood Banks in Korea: A Pilot Study for Cryopreservation Stability

PubMed Central

Seo, Soo Hyun; Shin, Sue; Roh, Eun Youn; Song, Eun Young; Oh, Sohee; Kim, Byoung Jae

2017-01-01

Background Maintaining the quality of cryopreserved cord blood is crucial. In this pilot study, we describe the results of the internal quality control program for a cord blood bank thus far. Methods Donated cord blood units unsuitable for transplantation were selected for internal quality control once a month. One unit of cord blood, aliquoted into 21 capillaries, was cryopreserved and thawed annually to analyze the total nucleated cell count, CD34+ cell count, cell viability test, and colony-forming units assay. Results No significant differences in the variables (total nucleated cell count, cell viability, CD34+ cell count) were observed between samples cryopreserved for one and two years. Upon comparing the variables before cryopreservation and post thawing with the capillaries of one year of storage, cell viability and CD34+ cell counts decreased significantly. The use of cord blood samples in capillaries, which can be easily stored for a long period, was similar to the methods used for testing segments attached to the cord blood unit. Conclusions The results of this study may be useful for determining the period during which the quality of cryopreserved cord blood units used for transplantation is maintained. PMID:28028998

HPLC fingerprint analysis combined with chemometrics for pattern recognition of ginger.

PubMed

Feng, Xu; Kong, Weijun; Wei, Jianhe; Ou-Yang, Zhen; Yang, Meihua

2014-03-01

Ginger, the fresh rhizome of Zingiber officinale Rosc. (Zingiberaceae), has been used worldwide; however, for a long time, there has been no standard approbated internationally for its quality control. To establish an efficacious and combinational method and pattern recognition technique for quality control of ginger. A simple, accurate and reliable method based on high-performance liquid chromatography with photodiode array (HPLC-PDA) detection was developed for establishing the chemical fingerprints of 10 batches of ginger from different markets in China. The method was validated in terms of precision, reproducibility and stability; and the relative standard deviations were all less than 1.57%. On the basis of this method, the fingerprints of 10 batches of ginger samples were obtained, which showed 16 common peaks. Coupled with similarity evaluation software, the similarities between each fingerprint of the sample and the simulative mean chromatogram were in the range of 0.998-1.000. Then, the chemometric techniques, including similarity analysis, hierarchical clustering analysis and principal component analysis were applied to classify the ginger samples. Consistent results were obtained to show that ginger samples could be successfully classified into two groups. This study revealed that HPLC-PDA method was simple, sensitive and reliable for fingerprint analysis, and moreover, for pattern recognition and quality control of ginger.

Ten tools of continuous quality improvement: a review and case example of hospital discharge.

PubMed

Ziegenfuss, J T; McKenna, C K

1995-01-01

Concepts and methods of continuous quality improvement have been endorsed by quality specialists in American Health care, and their use has convinced CEOs that industrial methods can make a contribution to health and medical care. For all the quality improvement publications, there are still few that offer a clear, concise definition and an explanation of the primary tools for teaching purposes. This report reviews ten continuous quality improvement methods including: problem solving cycle, affinity diagrams, cause and effect diagrams, Pareto diagrams, histograms, bar charts, control charts, scatter diagrams, checklists, and a process decision program chart. These do not represent an exhaustive list, but a set of commonly used tools. They are applied to a case study of bed utilization in a university hospital.

Design and numerical evaluation of full-authority flight control systems for conventional and thruster-augmented helicopters employed in NOE operations

NASA Technical Reports Server (NTRS)

Perri, Todd A.; Mckillip, R. M., Jr.; Curtiss, H. C., Jr.

1987-01-01

The development and methodology is presented for development of full-authority implicit model-following and explicit model-following optimal controllers for use on helicopters operating in the Nap-of-the Earth (NOE) environment. Pole placement, input-output frequency response, and step input response were used to evaluate handling qualities performance. The pilot was equipped with velocity-command inputs. A mathematical/computational trajectory optimization method was employed to evaluate the ability of each controller to fly NOE maneuvers. The method determines the optimal swashplate and thruster input histories from the helicopter's dynamics and the prescribed geometry and desired flying qualities of the maneuver. Three maneuvers were investigated for both the implicit and explicit controllers with and without auxiliary propulsion installed: pop-up/dash/descent, bob-up at 40 knots, and glideslope. The explicit controller proved to be superior to the implicit controller in performance and ease of design.

Bootstrap Signal-to-Noise Confidence Intervals: An Objective Method for Subject Exclusion and Quality Control in ERP Studies

PubMed Central

Parks, Nathan A.; Gannon, Matthew A.; Long, Stephanie M.; Young, Madeleine E.

2016-01-01

Analysis of event-related potential (ERP) data includes several steps to ensure that ERPs meet an appropriate level of signal quality. One such step, subject exclusion, rejects subject data if ERP waveforms fail to meet an appropriate level of signal quality. Subject exclusion is an important quality control step in the ERP analysis pipeline as it ensures that statistical inference is based only upon those subjects exhibiting clear evoked brain responses. This critical quality control step is most often performed simply through visual inspection of subject-level ERPs by investigators. Such an approach is qualitative, subjective, and susceptible to investigator bias, as there are no standards as to what constitutes an ERP of sufficient signal quality. Here, we describe a standardized and objective method for quantifying waveform quality in individual subjects and establishing criteria for subject exclusion. The approach uses bootstrap resampling of ERP waveforms (from a pool of all available trials) to compute a signal-to-noise ratio confidence interval (SNR-CI) for individual subject waveforms. The lower bound of this SNR-CI (SNRLB) yields an effective and objective measure of signal quality as it ensures that ERP waveforms statistically exceed a desired signal-to-noise criterion. SNRLB provides a quantifiable metric of individual subject ERP quality and eliminates the need for subjective evaluation of waveform quality by the investigator. We detail the SNR-CI methodology, establish the efficacy of employing this approach with Monte Carlo simulations, and demonstrate its utility in practice when applied to ERP datasets. PMID:26903849

The Method of Manufacturing Nonmetallic Test-Blocks on Different Sensitivity Classes

NASA Astrophysics Data System (ADS)

Kalinichenko, N. P.; Kalinichenko, A. N.; Lobanova, I. S.; Zaitseva, A. A.; Loboda, E. L.

2016-01-01

Nowadays in our modern world there is a vital question of quality control of details made from nonmetallic materials due to their wide spreading. Nondestructive penetrant testing is effective, and in some cases it is the only possible method of accidents prevention at high- risk sites. A brief review of check sample necessary for quality evaluation of penetrant materials is considered. There was offered a way of making agents for quality of penetrant materials testing according to different liquid penetrant testing sensibility classes.

Information integration and diagnosis analysis of equipment status and production quality for machining process

NASA Astrophysics Data System (ADS)

Zan, Tao; Wang, Min; Hu, Jianzhong

2010-12-01

Machining status monitoring technique by multi-sensors can acquire and analyze the machining process information to implement abnormity diagnosis and fault warning. Statistical quality control technique is normally used to distinguish abnormal fluctuations from normal fluctuations through statistical method. In this paper by comparing the advantages and disadvantages of the two methods, the necessity and feasibility of integration and fusion is introduced. Then an approach that integrates multi-sensors status monitoring and statistical process control based on artificial intelligent technique, internet technique and database technique is brought forward. Based on virtual instrument technique the author developed the machining quality assurance system - MoniSysOnline, which has been used to monitoring the grinding machining process. By analyzing the quality data and AE signal information of wheel dressing process the reason of machining quality fluctuation has been obtained. The experiment result indicates that the approach is suitable for the status monitoring and analyzing of machining process.

Describing methods and interventions: a protocol for the systematic analysis of the perioperative quality improvement literature.

PubMed

Jones, Emma; Lees, Nicholas; Martin, Graham; Dixon-Woods, Mary

2014-09-05

Quality improvement (QI) methods are widely used in surgery in an effort to improve care, often using techniques such as Plan-Do-Study-Act cycles to implement specific interventions. Explicit definition of both the QI method and quality intervention is necessary to enable the accurate replication of effective interventions in practice, facilitate cumulative learning, reduce research waste and optimise benefits to patients. This systematic review aims to assess quality of reporting of QI methods and quality interventions in perioperative care. Studies reporting on quality interventions implemented in perioperative care settings will be identified. Searches will be conducted in the Ovid SP version of Medline, Scopus, the Cochrane Central Register of Controlled Trials, the Cochrane Effective Practice and Organisation of Care database and the related articles function of PubMed. The journal BMJ Quality will be searched separately. Search strategy terms will relate to (i) surgery, (ii) QI and (iii) evaluation methods. Explicit exclusion and inclusion criteria will be applied. Data from studies will be extracted using a data extraction form. The Template for Intervention Description and Replication (TIDieR) checklist will be used to evaluate quality of reporting, together with additional items aimed at assessing QI methods specifically. PROSPERO http://CRD42014012845.

[The establishment and application of internal quality control system for real-time quantitative PCR detection of BCR-ABL (P210) transcript levels].

PubMed

Zhong, C Q; He, N; Hua, M Q; Wei, X D; Ma, D X; Ji, C Y

2016-09-14

Objective: To set internal quality control system of BCR-ABL (P210) transcript levels for real-time quantitative PCR (RQ-PCR). Methods: Using K562 cells and HL-60 cells, we prepared high- and low-level BCR-ABL internal quality control substance. The BCR-ABL (P210) transcript levels of internal quality control substance have been determined for 184 times together with clinical samples from August 2013 to October 2015. The slope rate, intercept and correlation coefficient of standard curve were calculated according to different reagent lots (lots number 20130303, 20131212, 20140411 and 20150327 are called R1、R2、R3 and R4 for short respectively), and the detection results of quality control substance were calculated according to different reagent lots and quality control substance lots (lots number 20130725, 20140611 are called Q1、Q2 for short respectively). Then the results were analyzed by Levey-Jennings quality control chart combined with Westgard multi-rules theory. Results: ①We analyzed the slope rate and intercept of standard curve. Fifty-three times of the R1 reagent detection, 80 times of the R3 reagent detection and 14 times of the R4 reagent detection were all under control. For 37 times detection of R2 reagent, the slope rate was out of control for 6 times. It was lower than x - s for the 2-8 tests and upper the average for the 12-37 tests. The intercept was out of control for 9 times, upper the x + s for the 1-8 tests and lower the average for the 12-37 tests. ② According to the detection results of quality control substance, for Q1 quality control substance, 49 tests by R1 reagent were under control, and 1 out of 23 tests by R2 reagent was out of control. For Q2 quality control substance, 14 tests by R2 reagent detection, 72 tests by R3 reagent detection and 14 tests by R4 reagent were all under control. Conclusion: The preparation of high- and low-level quality control substance using K562 and HL-60 cells was convenient and the detection results were reliable and stable. The application of quality control substance combined with slope rate and intercept in the internal quality control may contribute to quality assurance for quantitative detection of BCR-ABL (P210) transcript levels.

Improving Quality of Shoe Soles Product using Six Sigma

NASA Astrophysics Data System (ADS)

Jesslyn Wijaya, Athalia; Trusaji, Wildan; Akbar, Muhammad; Ma’ruf, Anas; Irianto, Dradjad

2018-03-01

A manufacture in Bandung produce kind of rubber-based product i.e. trim, rice rollers, shoe soles, etc. After penetrating the shoe soles market, the manufacture has met customer with tight quality control. Based on the past data, defect level of this product was 18.08% that caused the manufacture’s loss of time and money. Quality improvement effort was done using six sigma method that included phases of define, measure, analyse, improve, and control (DMAIC). In the design phase, the object’s problem and definition were defined. Delphi method was also used in this phase to identify critical factors. In the measure phase, the existing process stability and sigma quality level were measured. Fishbone diagram and failure mode and effect analysis (FMEA) were used in the next phase to analyse the root cause and determine the priority issues. Improve phase was done by designing alternative improvement strategy using 5W1H method. Some improvement efforts were identified, i.e. (i) modifying design of the hanging rack, (ii) create pantone colour book and check sheet, (iii) provide pedestrian line at compound department, (iv) buying stop watch, and (v) modifying shoe soles dies. Some control strategies for continuous improvement were proposed such as SOP or reward and punishment system.

Ultra-performance liquid chromatography fingerprinting for quality control of Phragmitis rhizoma (Lugen) produced in Baiyangdian

PubMed Central

Li, Hong; Gao, Yu-Mei; Zhang, Jing; Wang, Lin; Wang, Xiao-Xin

2013-01-01

Objective: To establish an ultra-performance liquid chromatography (UPLC) fingerprinting method for quality control of Phragmitis rhizoma from Baiyangdian. Materials and Methods: Ultrasonic extraction with 70% methanol was performed on 10 samples of P. rhizoma collected from 10 different villages in Baiyangdian. The sample solutions were analyzed by Waters UPLC equipped with the ACQUITY UPLC BEH C18 column and photodiode array (PDA) detector, and gradient eluted with acetonitrile/water as the mobile phase. The flow rate was set to 0.1 mL/min; the column temperature was set to 25°C; and the detection wavelength was set to 285 nm. Results: The chromatograms of the 10 samples showed 27 common peaks, of which one was identified as the ferulic acid standard. The similarity indexes were all above 0.82. Hierarchical cluster analysis showed that the constituents and their quantities differed according to the diameter of the original plant, which is related to its age. Conclusion: The UPLC fingerprinting method had the advantages of being fast, accurate, and highly efficient; this indicated that it can be used for quality control of P. rhizoma produced in Baiyangdian. Also, the relation between the quality and diameter/age of the plant needs to be further investigated. PMID:24124278

Engaging Direct Care Providers in Improving Infection Prevention and Control Practices Using Participatory Visual Methods.

PubMed

Backman, Chantal; Bruce, Natalie; Marck, Patricia; Vanderloo, Saskia

2016-01-01

The purpose of this quality improvement project was to determine the feasibility of using provider-led participatory visual methods to scrutinize 4 hospital units' infection prevention and control practices. Methods included provider-led photo walkabouts, photo elicitation sessions, and postimprovement photo walkabouts. Nurses readily engaged in using the methods to examine and improve their units' practices and reorganize their work environment.

A case study: application of statistical process control tool for determining process capability and sigma level.

PubMed

Chopra, Vikram; Bairagi, Mukesh; Trivedi, P; Nagar, Mona

2012-01-01

Statistical process control is the application of statistical methods to the measurement and analysis of variation process. Various regulatory authorities such as Validation Guidance for Industry (2011), International Conference on Harmonisation ICH Q10 (2009), the Health Canada guidelines (2009), Health Science Authority, Singapore: Guidance for Product Quality Review (2008), and International Organization for Standardization ISO-9000:2005 provide regulatory support for the application of statistical process control for better process control and understanding. In this study risk assessments, normal probability distributions, control charts, and capability charts are employed for selection of critical quality attributes, determination of normal probability distribution, statistical stability, and capability of production processes, respectively. The objective of this study is to determine tablet production process quality in the form of sigma process capability. By interpreting data and graph trends, forecasting of critical quality attributes, sigma process capability, and stability of process were studied. The overall study contributes to an assessment of process at the sigma level with respect to out-of-specification attributes produced. Finally, the study will point to an area where the application of quality improvement and quality risk assessment principles for achievement of six sigma-capable processes is possible. Statistical process control is the most advantageous tool for determination of the quality of any production process. This tool is new for the pharmaceutical tablet production process. In the case of pharmaceutical tablet production processes, the quality control parameters act as quality assessment parameters. Application of risk assessment provides selection of critical quality attributes among quality control parameters. Sequential application of normality distributions, control charts, and capability analyses provides a valid statistical process control study on process. Interpretation of such a study provides information about stability, process variability, changing of trends, and quantification of process ability against defective production. Comparative evaluation of critical quality attributes by Pareto charts provides the least capable and most variable process that is liable for improvement. Statistical process control thus proves to be an important tool for six sigma-capable process development and continuous quality improvement.

Method Development and Monitoring of Cyanotoxins in Water

EPA Science Inventory

This presentation describes method development of two ambient water LC/MS/MS methods for microcystins, cylindrospermopsin and anatoxin-a. Ruggedness of the methods will be demonstrated by evaluation of quality control samples derived from various water bodies across the country.

46 CFR 160.115-9 - Preapproval review.

Code of Federal Regulations, 2012 CFR

2012-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.115-19 and 160.115-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR part 159, subpart 159.010. (d) Plan quality...

46 CFR 160.115-9 - Preapproval review.

Code of Federal Regulations, 2014 CFR

2014-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.115-19 and 160.115-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR part 159, subpart 159.010. (d) Plan quality...

46 CFR 160.115-9 - Preapproval review.

Code of Federal Regulations, 2013 CFR

2013-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.115-19 and 160.115-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR part 159, subpart 159.010. (d) Plan quality...

Quality control tests of lab-reared Cydia pomonella and Cactoblastis cactorum field performance: Comparison of laboratory and field bioassays.

USDA-ARS?s Scientific Manuscript database

Research, operational, and commercial programs which rely on mass-reared insects of high quality and performance, need accurate methods for monitoring quality degradation during each step of production, handling and release. With continued interest in the use of the sterile insect technique (SIT) a...

Chemical analysis of Panax quinquefolius (North American ginseng): A review.

PubMed

Wang, Yaping; Choi, Hyung-Kyoon; Brinckmann, Josef A; Jiang, Xue; Huang, Linfang

2015-12-24

Panax quinquefolius (PQ) is one of the best-selling natural health products due to its proposed beneficial anti-aging, anti-cancer, anti-stress, anti-fatigue, and anxiolytic effects. In recent years, the quality of PQ has received considerable attention. Sensitive and accurate methods for qualitative and quantitative analyses of chemical constituents are necessary for the comprehensive quality control to ensure the safety and efficacy of PQ. This article reviews recent progress in the chemical analysis of PQ and its preparations. Numerous analytical techniques, including spectroscopy, thin-layer chromatography (TLC), gas chromatography (GC), high-performance liquid chromatography (HPLC), liquid chromatography/mass spectrometry (LC/MS), high-speed centrifugal partition chromatography (HSCPC), high-performance counter-current chromatography (HPCCC), nuclear magnetic resonance spectroscopy (NMR), and immunoassay, are described. Among these techniques, HPLC coupled with mass spectrometry (MS) is the most promising method for quality control. The challenges encountered in the chemical analysis of PQ are also briefly discussed, and the remaining questions regarding the quality control of PQ that require further investigation are highlighted. Copyright © 2015 Elsevier B.V. All rights reserved.

40 CFR 408.61 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... components of a waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory...

40 CFR 408.71 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... waste water amenable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory, page 217. (c...

40 CFR 408.81 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... components of a waste water amendable to measurement by the method described in Methods for Chemical Analysis of Water and Wastes, 1971, Environmental Protection Agency, Analytical Quality Control Laboratory...

[Investigation on the homogeneity and stability of quality controlling cosmetic samples containing arsenic].

PubMed

Dong, Bing; Song, Yu; Fan, Wenjia; Zhu, Ying

2010-11-01

To study the homogeneity and stability of arsenic in quality controlling cosmetic samples. Arsenic was determined by atomic fluorescence spectrophotometric method. The t-test and F-test were used to evaluate the significant difference of the within-bottle and between-bottle results with three batches. The RSDs of arsenic obtained in different time were compared with the relative expanding uncertainties to evaluate the stability. Average and variance of within-bottle and between-bottle results of arsenic were not different significantly. The RSDs of Arsenic were less than the relative expanding uncertainties. Quality controlling cosmetic samples containing arsenic were considered homogeneous and stable.

MASQOT: a method for cDNA microarray spot quality control

PubMed Central

Bylesjö, Max; Eriksson, Daniel; Sjödin, Andreas; Sjöström, Michael; Jansson, Stefan; Antti, Henrik; Trygg, Johan

2005-01-01

Background cDNA microarray technology has emerged as a major player in the parallel detection of biomolecules, but still suffers from fundamental technical problems. Identifying and removing unreliable data is crucial to prevent the risk of receiving illusive analysis results. Visual assessment of spot quality is still a common procedure, despite the time-consuming work of manually inspecting spots in the range of hundreds of thousands or more. Results A novel methodology for cDNA microarray spot quality control is outlined. Multivariate discriminant analysis was used to assess spot quality based on existing and novel descriptors. The presented methodology displays high reproducibility and was found superior in identifying unreliable data compared to other evaluated methodologies. Conclusion The proposed methodology for cDNA microarray spot quality control generates non-discrete values of spot quality which can be utilized as weights in subsequent analysis procedures as well as to discard spots of undesired quality using the suggested threshold values. The MASQOT approach provides a consistent assessment of spot quality and can be considered an alternative to the labor-intensive manual quality assessment process. PMID:16223442

Implementation of basic quality control tests for malaria medicines in Amazon Basin countries: results for the 2005–2010 period

PubMed Central

2012-01-01

Background Ensuring the quality of malaria medicines is crucial in working toward malaria control and eventual elimination. Unlike other validated tests that can assess all critical quality attributes, which is the standard for determining the quality of medicines, basic tests are significantly less expensive, faster, and require less skilled labour; yet, these tests provide reproducible data and information on several critical quality attributes, such as identity, purity, content, and disintegration. Visual and physical inspection also provides valuable information about the manufacturing and the labelling of medicines, and in many cases this inspection is sufficient to detect counterfeit medicines. The Promoting the Quality of Medicines (PQM) programme has provided technical assistance to Amazon Malaria Initiative (AMI) countries to implement the use of basic tests as a key screening mechanism to assess the quality of malaria medicines available to patients in decentralized regions. Methods Trained personnel from the National Malaria Control Programmes (NMCPs), often in collaboration with country’s Official Medicine Control Laboratory (OMCL), developed country- specific protocols that encompassed sampling methods, sample analysis, and data reporting. Sampling sites were selected based on malaria burden, accessibility, and geographical location. Convenience sampling was performed and countries were recommended to store the sampled medicines under conditions that did not compromise their quality. Basic analytical tests, such as disintegration and thin layer chromatography (TLC), were performed utilizing a portable mini-laboratory. Results Results were originally presented at regional meetings in a non-standardized format that lacked relevant medicines information. However, since 2008 information has been submitted utilizing a template specifically developed by PQM for that purpose. From 2005 to 2010, the quality of 1,663 malaria medicines from seven AMI countries was evaluated, mostly collected from the public sector, 1,445/1,663 (86.9%). Results indicate that 193/1,663 (11.6%) were found not to meet quality specifications. Most failures were reported during visual and physical inspection, 142/1663 (8.5%), and most of these were due to expired medicines, 118/142 (83.1%). Samples failing TLC accounted for 27/1,663 (1.6%) and those failing disintegration accounted for 24/1,663 (1.4%). Medicines quality failures decreased significantly during the last two years. Conclusions Basic tests revealed that the quality of medicines in the public sector improved over the years, since the implementation of this type of quality monitoring programme in 2005. However, the lack of consistent confirmatory tests in the quality control (QC) laboratory, utilizing methods that can also evaluate additional quality attributes, could still mask quality issues. In the future, AMI countries should improve coordination with their health authorities and their QC lab consistently, to provide a more complete picture of malaria medicines quality and support the implementation of corrective actions. Facilities in the private and informal sectors also should be included when these sectors constitute an important source of medicines used by malaria patients. PMID:22704680

Evaluating the Good Ontology Design Guideline (GoodOD) with the ontology quality requirements and evaluation method and metrics (OQuaRE).

PubMed

Duque-Ramos, Astrid; Boeker, Martin; Jansen, Ludger; Schulz, Stefan; Iniesta, Miguela; Fernández-Breis, Jesualdo Tomás

2014-01-01

To (1) evaluate the GoodOD guideline for ontology development by applying the OQuaRE evaluation method and metrics to the ontology artefacts that were produced by students in a randomized controlled trial, and (2) informally compare the OQuaRE evaluation method with gold standard and competency questions based evaluation methods, respectively. In the last decades many methods for ontology construction and ontology evaluation have been proposed. However, none of them has become a standard and there is no empirical evidence of comparative evaluation of such methods. This paper brings together GoodOD and OQuaRE. GoodOD is a guideline for developing robust ontologies. It was previously evaluated in a randomized controlled trial employing metrics based on gold standard ontologies and competency questions as outcome parameters. OQuaRE is a method for ontology quality evaluation which adapts the SQuaRE standard for software product quality to ontologies and has been successfully used for evaluating the quality of ontologies. In this paper, we evaluate the effect of training in ontology construction based on the GoodOD guideline within the OQuaRE quality evaluation framework and compare the results with those obtained for the previous studies based on the same data. Our results show a significant effect of the GoodOD training over developed ontologies by topics: (a) a highly significant effect was detected in three topics from the analysis of the ontologies of untrained and trained students; (b) both positive and negative training effects with respect to the gold standard were found for five topics. The GoodOD guideline had a significant effect over the quality of the ontologies developed. Our results show that GoodOD ontologies can be effectively evaluated using OQuaRE and that OQuaRE is able to provide additional useful information about the quality of the GoodOD ontologies.

An engineering approach to controlling indoor air quality.

PubMed

Woods, J E

1991-11-01

Evidence is accumulating that indicates air quality problems in residential and commercial buildings are nearly always associated with inadequacies in building design and methods of operation. Thus, the very systems depended on to control the indoor environment can become indirect sources of contamination if diligence is not exercised at each stage of a building's life: a) planning and design, b) construction and commissioning, c) operation, and d) demolition or renovation. In this paper, an engineering perspective is presented in which the existing building stock is characterized in terms of its environmental performance. Preliminary data indicate that 20 to 30% of the existing buildings have sufficient problems to manifest as sick-building syndrome or building-related illness, while another 10 to 20% may have undetected problems. Thus, only about 50 to 70% of the existing buildings qualify as healthy buildings. Two methods and three mechanisms of control are described to achieve "acceptable" indoor air quality: source control and exposure control. If sources cannot be removed, some level of occupant exposure will result. To control exposures with acceptable values, the primary sensory receptors of the occupants (i.e., thermal, ocular, auditory, and olfactory) cannot be excessively stimulated. The three exposure control mechanisms are conduction, radiation, and convection. To achieve acceptable occupant responses, it is often practical to integrate the mechanisms of radiation and convection in heating, ventilating, and air conditioning systems that are designed to provide acceptable thermal, acoustic, and air quality conditions within occupied spaces.(ABSTRACT TRUNCATED AT 250 WORDS)

An engineering approach to controlling indoor air quality.

PubMed Central

Woods, J E

1991-01-01

Evidence is accumulating that indicates air quality problems in residential and commercial buildings are nearly always associated with inadequacies in building design and methods of operation. Thus, the very systems depended on to control the indoor environment can become indirect sources of contamination if diligence is not exercised at each stage of a building's life: a) planning and design, b) construction and commissioning, c) operation, and d) demolition or renovation. In this paper, an engineering perspective is presented in which the existing building stock is characterized in terms of its environmental performance. Preliminary data indicate that 20 to 30% of the existing buildings have sufficient problems to manifest as sick-building syndrome or building-related illness, while another 10 to 20% may have undetected problems. Thus, only about 50 to 70% of the existing buildings qualify as healthy buildings. Two methods and three mechanisms of control are described to achieve "acceptable" indoor air quality: source control and exposure control. If sources cannot be removed, some level of occupant exposure will result. To control exposures with acceptable values, the primary sensory receptors of the occupants (i.e., thermal, ocular, auditory, and olfactory) cannot be excessively stimulated. The three exposure control mechanisms are conduction, radiation, and convection. To achieve acceptable occupant responses, it is often practical to integrate the mechanisms of radiation and convection in heating, ventilating, and air conditioning systems that are designed to provide acceptable thermal, acoustic, and air quality conditions within occupied spaces.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:1821369

Training of U.S. Air Traffic Controllers. (IDA Report No. R-206).

ERIC Educational Resources Information Center

Henry, James H.; And Others

The report reviews the evolution of existing national programs for air traffic controller training, estimates the number of persons requiring developmental and supplementary training, examines present controller selection and training programs, investigates performance measurement methods, considers standardization and quality control, discusses…

[Pursuit of economic efficiency in the hospital laboratory--full automatic re-test system of clinical chemistry, hematology, immunology and cost control system].

PubMed

Chiba, M

2000-10-01

Further business improvement is requested due to finance-based fluctuation and the influence of the revision in the medical treatment law. Therefore, new laboratories are needed. To achieving this in our hospital, economic efficiency is being pursued. The first issue is the use of space, the second issue is labor-saving. The third issue is the simplification of business procedures. There is individual quality control by the zonal verification method that we developed, as well as the quality control of the batch method using controlled substances. The four issue is cost control. By controlling the delivery and use of reagents and materials including the term of validity control, we made an effort to abolition defective stock. The fifth issue is correspondence to circulation style society. The disposal of laboratory garbage is a major issue. We controlled garbage that occurs unnecessarily. Furthermore, we are improving the demand for reagents that exceeds the specification and use reagent containers.

Quality control for quantitative PCR based on amplification compatibility test.

PubMed

Tichopad, Ales; Bar, Tzachi; Pecen, Ladislav; Kitchen, Robert R; Kubista, Mikael; Pfaffl, Michael W

2010-04-01

Quantitative qPCR is a routinely used method for the accurate quantification of nucleic acids. Yet it may generate erroneous results if the amplification process is obscured by inhibition or generation of aberrant side-products such as primer dimers. Several methods have been established to control for pre-processing performance that rely on the introduction of a co-amplified reference sequence, however there is currently no method to allow for reliable control of the amplification process without directly modifying the sample mix. Herein we present a statistical approach based on multivariate analysis of the amplification response data generated in real-time. The amplification trajectory in its most resolved and dynamic phase is fitted with a suitable model. Two parameters of this model, related to amplification efficiency, are then used for calculation of the Z-score statistics. Each studied sample is compared to a predefined reference set of reactions, typically calibration reactions. A probabilistic decision for each individual Z-score is then used to identify the majority of inhibited reactions in our experiments. We compare this approach to univariate methods using only the sample specific amplification efficiency as reporter of the compatibility. We demonstrate improved identification performance using the multivariate approach compared to the univariate approach. Finally we stress that the performance of the amplification compatibility test as a quality control procedure depends on the quality of the reference set. Copyright 2010 Elsevier Inc. All rights reserved.

Preparation method and quality control of multigamma volume sources with different matrices.

PubMed

Listkowska, A; Lech, E; Saganowski, P; Tymiński, Z; Dziel, T; Cacko, D; Ziemek, T; Kołakowska, E; Broda, R

2018-04-01

The aim of the work was to develop new radioactive standard sources based on epoxy resins. The optimal proportions of the components and the homogeneity of the matrices were determined. The activity of multigamma sources prepared in Marinelli beakers was determined with reference to the National Standard of Radionuclides Activity in Poland. The difference of radionuclides activity values determined using calibrated gamma spectrometer and the activity of standard solutions used are in most cases significantly lower than measurement uncertainty limits. Sources production method and quality control procedure have been developed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Using the scanning electron microscope on the production line to assure quality semiconductors

NASA Technical Reports Server (NTRS)

Adolphsen, J. W.; Anstead, R. J.

1972-01-01

The use of the scanning electron microscope to detect metallization defects introduced during batch processing of semiconductor devices is discussed. A method of determining metallization integrity was developed which culminates in a procurement specification using the scanning microscope on the production line as a quality control tool. Batch process control of the metallization operation is monitored early in the manufacturing cycle.

40 CFR 417.191 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... methylene blue active substances amenable to measurement by the method described in “Methods for Chemical Analysis of Water and Wastes,” 1971, Environmental Protection Agency, Analytical Quality Control Laboratory...

A micro-vibration generated method for testing the imaging quality on ground of space remote sensing

NASA Astrophysics Data System (ADS)

Gu, Yingying; Wang, Li; Wu, Qingwen

2018-03-01

In this paper, a novel method is proposed, which can simulate satellite platform micro-vibration and test the impact of satellite micro-vibration on imaging quality of space optical remote sensor on ground. The method can generate micro-vibration of satellite platform in orbit from vibrational degrees of freedom, spectrum, magnitude, and coupling path. Experiment results show that the relative error of acceleration control is within 7%, in frequencies from 7Hz to 40Hz. Utilizing this method, the system level test about the micro-vibration impact on imaging quality of space optical remote sensor can be realized. This method will have an important applications in testing micro-vibration tolerance margin of optical remote sensor, verifying vibration isolation and suppression performance of optical remote sensor, exploring the principle of micro-vibration impact on imaging quality of optical remote sensor.

Image quality in thoracic 4D cone-beam CT: A sensitivity analysis of respiratory signal, binning method, reconstruction algorithm, and projection angular spacing

PubMed Central

Shieh, Chun-Chien; Kipritidis, John; O’Brien, Ricky T.; Kuncic, Zdenka; Keall, Paul J.

2014-01-01

Purpose: Respiratory signal, binning method, and reconstruction algorithm are three major controllable factors affecting image quality in thoracic 4D cone-beam CT (4D-CBCT), which is widely used in image guided radiotherapy (IGRT). Previous studies have investigated each of these factors individually, but no integrated sensitivity analysis has been performed. In addition, projection angular spacing is also a key factor in reconstruction, but how it affects image quality is not obvious. An investigation of the impacts of these four factors on image quality can help determine the most effective strategy in improving 4D-CBCT for IGRT. Methods: Fourteen 4D-CBCT patient projection datasets with various respiratory motion features were reconstructed with the following controllable factors: (i) respiratory signal (real-time position management, projection image intensity analysis, or fiducial marker tracking), (ii) binning method (phase, displacement, or equal-projection-density displacement binning), and (iii) reconstruction algorithm [Feldkamp–Davis–Kress (FDK), McKinnon–Bates (MKB), or adaptive-steepest-descent projection-onto-convex-sets (ASD-POCS)]. The image quality was quantified using signal-to-noise ratio (SNR), contrast-to-noise ratio, and edge-response width in order to assess noise/streaking and blur. The SNR values were also analyzed with respect to the maximum, mean, and root-mean-squared-error (RMSE) projection angular spacing to investigate how projection angular spacing affects image quality. Results: The choice of respiratory signals was found to have no significant impact on image quality. Displacement-based binning was found to be less prone to motion artifacts compared to phase binning in more than half of the cases, but was shown to suffer from large interbin image quality variation and large projection angular gaps. Both MKB and ASD-POCS resulted in noticeably improved image quality almost 100% of the time relative to FDK. In addition, SNR values were found to increase with decreasing RMSE values of projection angular gaps with strong correlations (r ≈ −0.7) regardless of the reconstruction algorithm used. Conclusions: Based on the authors’ results, displacement-based binning methods, better reconstruction algorithms, and the acquisition of even projection angular views are the most important factors to consider for improving thoracic 4D-CBCT image quality. In view of the practical issues with displacement-based binning and the fact that projection angular spacing is not currently directly controllable, development of better reconstruction algorithms represents the most effective strategy for improving image quality in thoracic 4D-CBCT for IGRT applications at the current stage. PMID:24694143

Field methods and quality-assurance plan for water-quality activities and water-level measurements, U.S. Geological Survey, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Bartholomay, Roy C.; Maimer, Neil V.; Wehnke, Amy J.

2014-01-01

Water-quality activities and water-level measurements by the personnel of the U.S. Geological Survey (USGS) Idaho National Laboratory (INL) Project Office coincide with the USGS mission of appraising the quantity and quality of the Nation’s water resources. The activities are carried out in cooperation with the U.S. Department of Energy (DOE) Idaho Operations Office. Results of the water-quality and hydraulic head investigations are presented in various USGS publications or in refereed scientific journals and the data are stored in the National Water Information System (NWIS) database. The results of the studies are used by researchers, regulatory and managerial agencies, and interested civic groups. In the broadest sense, quality assurance refers to doing the job right the first time. It includes the functions of planning for products, review and acceptance of the products, and an audit designed to evaluate the system that produces the products. Quality control and quality assurance differ in that quality control ensures that things are done correctly given the “state-of-the-art” technology, and quality assurance ensures that quality control is maintained within specified limits.

Effects of three highway-runoff detention methods on water quality of the surficial aquifer system in central Florida

USGS Publications Warehouse

Schiffer, D.M.

1989-01-01

Water quality of the surficial aquifer system in central Florida was evaluated at one exfiltration pipe, two ponds (detention and retention), and two swales in central Florida, representing three runoff-detention methods, to detect any effect from infiltrating highway runoff. Concentrations of major ions, metals, and nutrients in groundwater and bottom sediments were measured from 1984 through 1986. At each study area, constituent concentrations in groundwater near the structure were compared to concentrations in groundwater from an upgradient control site. Groundwater quality data were also pooled by detention method and statistically compared to detect any significant differences between methods. Significantly greater mean phosphorus concentrations in groundwater near the exfiltration pipe than those in the control well was the only evidence of increasing constituent concentrations in groundwater near structures. The quality of water was more variable, and had greater constituent concentrations in the unsaturated zone than in the saturated zone near the exfiltration pipe. Values of water quality variables measured in groundwater at all study areas generally were within State drinking water standards. The main exception was dissolved iron, which commonly exceeded 300 micrograms/L at one swale and the detention pond. Results of the study indicate that natural processes occurring in soils attenuate inorganic constituent concentrations prior to reaching the receiving groundwater. However, organic compounds detected in bottom sediments at the retention pond indicate a potential problem that may eventually affect the quality of the receiving groundwater. (USGS)

High perfomance liquid chromatography fingerprint analysis for quality control of brotowali (Tinospora crispa)

NASA Astrophysics Data System (ADS)

Syarifah, V. B.; Rafi, M.; Wahyuni, W. T.

2017-05-01

Brotowali (Tinospora crispa) is widely used in Indonesia as ingredient of herbal medicine formulation. To ensure the quality, safety, and efficacy of herbal medicine products, its chemical constituents should be continuously evaluated. High performance liquid chromatography (HPLC) fingerprint is one of powerful technique for this quality control process. In this study, HPLC fingerprint analysis method was developed for quality control of brotowali. HPLC analysis was performed in C18 column and detection was performed using photodiode array detector. The optimum mobile phase for brotowali fingerprint was acetonitrile (ACN) and 0.1% formic acid in gradient elution mode at a flow rate of 1 mL/min. The number of peaks detected in HPLC fingerprint of brotowali was 32 peaks and 23 peaks for stems and leaves, respectively. Berberine as marker compound was detected at retention time of 20.525 minutes. Evaluation of analytical performance including precision, reproducibility, and stability prove that this HPLC fingerprint analysis was reliable and could be applied for quality control of brotowali.

Validation of selected analytical methods using accuracy profiles to assess the impact of a Tobacco Heating System on indoor air quality.

PubMed

Mottier, Nicolas; Tharin, Manuel; Cluse, Camille; Crudo, Jean-René; Lueso, María Gómez; Goujon-Ginglinger, Catherine G; Jaquier, Anne; Mitova, Maya I; Rouget, Emmanuel G R; Schaller, Mathieu; Solioz, Jennifer

2016-09-01

Studies in environmentally controlled rooms have been used over the years to assess the impact of environmental tobacco smoke on indoor air quality. As new tobacco products are developed, it is important to determine their impact on air quality when used indoors. Before such an assessment can take place it is essential that the analytical methods used to assess indoor air quality are validated and shown to be fit for their intended purpose. Consequently, for this assessment, an environmentally controlled room was built and seven analytical methods, representing eighteen analytes, were validated. The validations were carried out with smoking machines using a matrix-based approach applying the accuracy profile procedure. The performances of the methods were compared for all three matrices under investigation: background air samples, the environmental aerosol of Tobacco Heating System THS 2.2, a heat-not-burn tobacco product developed by Philip Morris International, and the environmental tobacco smoke of a cigarette. The environmental aerosol generated by the THS 2.2 device did not have any appreciable impact on the performances of the methods. The comparison between the background and THS 2.2 environmental aerosol samples generated by smoking machines showed that only five compounds were higher when THS 2.2 was used in the environmentally controlled room. Regarding environmental tobacco smoke from cigarettes, the yields of all analytes were clearly above those obtained with the other two air sample types. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Toward a perceptual video-quality metric

NASA Astrophysics Data System (ADS)

Watson, Andrew B.

1998-07-01

The advent of widespread distribution of digital video creates a need for automated methods for evaluating the visual quality of digital video. This is particularly so since most digital video is compressed using lossy methods, which involve the controlled introduction of potentially visible artifacts. Compounding the problem is the bursty nature of digital video, which requires adaptive bit allocation based on visual quality metrics, and the economic need to reduce bit-rate to the lowest level that yields acceptable quality. In previous work, we have developed visual quality metrics for evaluating, controlling,a nd optimizing the quality of compressed still images. These metrics incorporate simplified models of human visual sensitivity to spatial and chromatic visual signals. Here I describe a new video quality metric that is an extension of these still image metrics into the time domain. Like the still image metrics, it is based on the Discrete Cosine Transform. An effort has been made to minimize the amount of memory and computation required by the metric, in order that might be applied in the widest range of applications. To calibrate the basic sensitivity of this metric to spatial and temporal signals we have made measurements of visual thresholds for temporally varying samples of DCT quantization noise.

MO-A-16A-01: QA Procedures and Metrics: In Search of QA Usability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sathiaseelan, V; Thomadsen, B

Radiation therapy has undergone considerable changes in the past two decades with a surge of new technology and treatment delivery methods. The complexity of radiation therapy treatments has increased and there has been increased awareness and publicity about the associated risks. In response, there has been proliferation of guidelines for medical physicists to adopt to ensure that treatments are delivered safely. Task Group recommendations are copious, and clinical physicists' hours are longer, stretched to various degrees between site planning and management, IT support, physics QA, and treatment planning responsibilities.Radiation oncology has many quality control practices in place to ensure themore » delivery of high-quality, safe treatments. Incident reporting systems have been developed to collect statistics about near miss events at many radiation oncology centers. However, tools are lacking to assess the impact of these various control measures. A recent effort to address this shortcoming is the work of Ford et al (2012) who recently published a methodology enumerating quality control quantification for measuring the effectiveness of safety barriers. Over 4000 near-miss incidents reported from 2 academic radiation oncology clinics were analyzed using quality control quantification, and a profile of the most effective quality control measures (metrics) was identified.There is a critical need to identify a QA metric to help the busy clinical physicists to focus their limited time and resources most effectively in order to minimize or eliminate errors in the radiation treatment delivery processes. In this symposium the usefulness of workflows and QA metrics to assure safe and high quality patient care will be explored.Two presentations will be given:Quality Metrics and Risk Management with High Risk Radiation Oncology ProceduresStrategies and metrics for quality management in the TG-100 Era Learning Objectives: Provide an overview and the need for QA usability metrics: Different cultures/practices affecting the effectiveness of methods and metrics. Show examples of quality assurance workflows, Statistical process control, that monitor the treatment planning and delivery process to identify errors. To learn to identify and prioritize risks and QA procedures in radiation oncology. Try to answer the question: Can a quality assurance program aided by quality assurance metrics help minimize errors and ensure safe treatment delivery. Should such metrics be institution specific.« less

Development of an environmental chamber for evaluating the performance of low-cost air quality sensors under controlled conditions

NASA Astrophysics Data System (ADS)

Papapostolou, Vasileios; Zhang, Hang; Feenstra, Brandon J.; Polidori, Andrea

2017-12-01

A state-of-the-art integrated chamber system has been developed for evaluating the performance of low-cost air quality sensors. The system contains two professional grade chamber enclosures. A 1.3 m3 stainless-steel outer chamber and a 0.11 m3 Teflon-coated stainless-steel inner chamber are used to create controlled aerosol and gaseous atmospheres, respectively. Both chambers are temperature and relative humidity controlled with capability to generate a wide range of environmental conditions. The system is equipped with an integrated zero-air system, an ozone and two aerosol generation systems, a dynamic dilution calibrator, certified gas cylinders, an array of Federal Reference Method (FRM), Federal Equivalent Method (FEM), and Best Available Technology (BAT) reference instruments and an automated control and sequencing software. Our experiments have demonstrated that the chamber system is capable of generating stable and reproducible aerosol and gas concentrations at low, medium, and high levels. This paper discusses the development of the chamber system along with the methods used to quantitatively evaluate sensor performance. Considering that a significant number of academic and research institutions, government agencies, public and private institutions, and individuals are becoming interested in developing and using low-cost air quality sensors, it is important to standardize the procedures used to evaluate their performance. The information discussed herein provides a roadmap for entities who are interested in characterizing air quality sensors in a rigorous, systematic and reproducible manner.

Identification of quality markers of Yuanhu Zhitong tablets based on integrative pharmacology and data mining.

PubMed

Li, Ke; Li, Junfang; Su, Jin; Xiao, Xuefeng; Peng, Xiujuan; Liu, Feng; Li, Defeng; Zhang, Yi; Chong, Tao; Xu, Haiyu; Liu, Changxiao; Yang, Hongjun

2018-03-07

The quality evaluation of traditional Chinese medicine (TCM) formulations is needed to guarantee the safety and efficacy. In our laboratory, we established interaction rules between chemical quality control and biological activity evaluations to study Yuanhu Zhitong tablets (YZTs). Moreover, a quality marker (Q-marker) has recently been proposed as a new concept in the quality control of TCM. However, no appropriate methods are available for the identification of Q-markers from the complex TCM systems. We aimed to use an integrative pharmacological (IP) approach to further identify Q-markers from YZTs through the integration of multidisciplinary knowledge. In addition, data mining was used to determine the correlation between multiple constituents of this TCM and its bioactivity to improve quality control. The IP approach was used to identify the active constituents of YZTs and elucidate the molecular mechanisms by integrating chemical and biosynthetic analyses, drug metabolism, and network pharmacology. Data mining methods including grey relational analysis (GRA) and least squares support vector machine (LS-SVM) regression techniques, were used to establish the correlations among the constituents and efficacy, and dose efficacy in multiple dimensions. Seven constituents (tetrahydropalmatine, α-allocryptopine, protopine, corydaline, imperatorin, isoimperatorin, and byakangelicin) were identified as Q-markers of YZT using IP based on their high abundance, specific presence in the individual herbal constituents and the product, appropriate drug-like properties, and critical contribution to the bioactivity of the mixture of YZT constituents. Moreover, three Q-markers (protopine, α-allocryptopine, and corydaline) were highly correlated with the multiple bioactivities of the YZTs, as found using data mining. Finally, three constituents (tetrahydropalmatine, corydaline, and imperatorin) were chosen as minimum combinations that both distinguished the authentic components from false products and indicated the intensity of bioactivity to improve the quality control of YZTs. Tetrahydropalmatine, imperatorin, and corydaline could be used as minimum combinations to effectively control the quality of YZTs. Copyright © 2018. Published by Elsevier GmbH.

Theory and practice for measuring health care quality

PubMed Central

Berwick, Donald M.; Knapp, Marian Gilbert

1987-01-01

As competition, cost control, and new modes of delivery emerge in health care, there is a need to reexamine both the traditional definitions of health care quality and the methods by which it is measured. Industries other than health care have much to teach regarding the methods for obtaining, analyzing, and displaying data; techniques for problem identification, problem solving, and reassessment; and ideas about organizational factors that produce a high quality product or service. The Quality-of-Care Measurement Department at the Harvard Community Health Plan has built a program that draws from a distinguished health care quality assurance tradition and incorporates techniques that have been successful in other industries. PMID:10312319

Projection pursuit water quality evaluation model based on chicken swam algorithm

NASA Astrophysics Data System (ADS)

Hu, Zhe

2018-03-01

In view of the uncertainty and ambiguity of each index in water quality evaluation, in order to solve the incompatibility of evaluation results of individual water quality indexes, a projection pursuit model based on chicken swam algorithm is proposed. The projection index function which can reflect the water quality condition is constructed, the chicken group algorithm (CSA) is introduced, the projection index function is optimized, the best projection direction of the projection index function is sought, and the best projection value is obtained to realize the water quality evaluation. The comparison between this method and other methods shows that it is reasonable and feasible to provide decision-making basis for water pollution control in the basin.

[UPLC characteristic chromatographic profile of Poria].

PubMed

Zhang, Qi; Wang, Zhenzhong; Xiao, Wei; Zhang, Liangqi; Bi, Kaishun; Jia, Ying

2012-04-01

To establish a UPLC characteristic chromatographic profile analysis method to quickly assess Poria quality and provide basis fro controlling Poria quality. The UPLC characteristic chromatographic profiles of fifteen batches of Poria were determined by ACQUITY UPLC, with HSS T3 Column (2.1 mm x 100 mm, 1.8 microm) eluted with the mobile phases of water containing 0.05% phosphoric acid and acetonitrile in gradient mode. The detection wavelength was set at 243 nm. The common mode of the UPLC characteristic chromatographic profile was set up. There were 20 common peaks, seven of which were identified, and the similar degrees of the fifteen samples to the common mode were between 0.787 and 0.974. The method was so time-saving that it can be used for the quality control of Poria.

Automatic first-arrival picking based on extended super-virtual interferometry with quality control procedure

NASA Astrophysics Data System (ADS)

An, Shengpei; Hu, Tianyue; Liu, Yimou; Peng, Gengxin; Liang, Xianghao

2017-12-01

Static correction is a crucial step of seismic data processing for onshore play, which frequently has a complex near-surface condition. The effectiveness of the static correction depends on an accurate determination of first-arrival traveltimes. However, it is difficult to accurately auto-pick the first arrivals for data with low signal-to-noise ratios (SNR), especially for those measured in the area of the complex near-surface. The technique of the super-virtual interferometry (SVI) has the potential to enhance the SNR of first arrivals. In this paper, we develop the extended SVI with (1) the application of the reverse correlation to improve the capability of SNR enhancement at near-offset, and (2) the usage of the multi-domain method to partially overcome the limitation of current method, given insufficient available source-receiver combinations. Compared to the standard SVI, the SNR enhancement of the extended SVI can be up to 40%. In addition, we propose a quality control procedure, which is based on the statistical characteristics of multichannel recordings of first arrivals. It can auto-correct the mispicks, which might be spurious events generated by the SVI. This procedure is very robust, highly automatic and it can accommodate large data in batches. Finally, we develop one automatic first-arrival picking method to combine the extended SVI and the quality control procedure. Both the synthetic and the field data examples demonstrate that the proposed method is able to accurately auto-pick first arrivals in seismic traces with low SNR. The quality of the stacked seismic sections obtained from this method is much better than those obtained from an auto-picking method, which is commonly employed by the commercial software.

SAM Technical Contacts

EPA Pesticide Factsheets

These technical contacts are available to help with questions regarding method deviations, modifications, sample problems or interferences, quality control requirements, the use of alternative methods, or the need to address analytes or sample types.

Importance of implementing an analytical quality control system in a core laboratory.

PubMed

Marques-Garcia, F; Garcia-Codesal, M F; Caro-Narros, M R; Contreras-SanFeliciano, T

2015-01-01

The aim of the clinical laboratory is to provide useful information for screening, diagnosis and monitoring of disease. The laboratory should ensure the quality of extra-analytical and analytical process, based on set criteria. To do this, it develops and implements a system of internal quality control, designed to detect errors, and compare its data with other laboratories, through external quality control. In this way it has a tool to detect the fulfillment of the objectives set, and in case of errors, allowing corrective actions to be made, and ensure the reliability of the results. This article sets out to describe the design and implementation of an internal quality control protocol, as well as its periodical assessment intervals (6 months) to determine compliance with pre-determined specifications (Stockholm Consensus(1)). A total of 40 biochemical and 15 immunochemical methods were evaluated using three different control materials. Next, a standard operation procedure was planned to develop a system of internal quality control that included calculating the error of the analytical process, setting quality specifications, and verifying compliance. The quality control data were then statistically depicted as means, standard deviations, and coefficients of variation, as well as systematic, random, and total errors. The quality specifications were then fixed and the operational rules to apply in the analytical process were calculated. Finally, our data were compared with those of other laboratories through an external quality assurance program. The development of an analytical quality control system is a highly structured process. This should be designed to detect errors that compromise the stability of the analytical process. The laboratory should review its quality indicators, systematic, random and total error at regular intervals, in order to ensure that they are meeting pre-determined specifications, and if not, apply the appropriate corrective actions. Copyright © 2015 SECA. Published by Elsevier Espana. All rights reserved.

Quality measures in applications of image restoration.

PubMed

Kriete, A; Naim, M; Schafer, L

2001-01-01

We describe a new method for the estimation of image quality in image restoration applications. We demonstrate this technique on a simulated data set of fluorescent beads, in comparison with restoration by three different deconvolution methods. Both the number of iterations and a regularisation factor are varied to enforce changes in the resulting image quality. First, the data sets are directly compared by an accuracy measure. These values serve to validate the image quality descriptor, which is developed on the basis of optical information theory. This most general measure takes into account the spectral energies and the noise, weighted in a logarithmic fashion. It is demonstrated that this method is particularly helpful as a user-oriented method to control the output of iterative image restorations and to eliminate the guesswork in choosing a suitable number of iterations.

Sleep quality in patients with xerostomia: a prospective and randomized case-control study.

PubMed

Lopez-Jornet, Pia; Lucero Berdugo, Maira; Fernandez-Pujante, Alba; C, Castillo Felipe; Lavella C, Zamora; A, Pons-Fuster; J, Silvestre Rangil; Silvestre, Francisco Javier

2016-01-01

Objectives To investigate sleep quality, anxiety/depression and quality-of-life in patients with xerostomia. Materials and methods This prospective, observational, cross-sectional study was conducted among a group of xerostomia patients (n = 30) compared with 30 matched control subjects. The following evaluation scales were used to assess the psychological profile of each patient: the Hospital Anxiety and Depression Scale, the Oral Health Impact Profile-14 (OHIP-14), the Xerostomia Inventory, the Pittsburgh Sleep Quality Index (PSQI) and the Epworth Sleepiness Scale (ESS). Results The PSQI obtained 5.3 3 ± 1.78 for patients with xerostomia compared with 4.26 ± 1.01 for control subjects (p = 0.006); ESS obtained 5.7 ± 2.1 for test patients vs 4.4 0 ± 1 for control subjects (p = 0.010). Statistical regression analysis showed that xerostomia was significantly associated with depression (p = 0.027). Conclusions Patients with xerostomia exhibited significant decreases in sleep quality compared with control subjects.

Role of technology in supporting quality control and treatment fidelity in a family caregiver clinical trial.

PubMed

Farran, Carol J; Etkin, Caryn D; McCann, Judith J; Paun, Olimpia; Eisenstein, Amy R; Wilbur, Joellen

2011-11-01

This article describes how a family caregiver lifestyle physical activity clinical trial uses research technology to enhance quality control and treatment fidelity. This trial uses a range of Internet, Blaise(®) Windows-based software and Echo Server technologies to support quality control issues, such as data collection, data entry, and study management advocated by the clinical trials literature, and to ensure treatment fidelity concerning intervention implementation (i.e., design, training, delivery, receipt, and enactment) as proposed by the National Institutes of Health Behavior Change Consortium. All research staff are trained to use these technologies. Strengths of this technological approach to support quality control and treatment fidelity include the comprehensive plan, involvement of all staff, and ability to maintain accurate and timely data. Limitations include the upfront time and costs for developing and testing these technological methods, and having support staff readily available to address technological issues if they occur.

Improved quality monitoring of multi-center acupuncture clinical trials in China

PubMed Central

2009-01-01

Background In 2007, the Chinese Science Division of the State Administration of Traditional Chinese Medicine(TCM) convened a special conference to discuss quality control for TCM clinical research. Control and assurance standards were established to guarantee the quality of clinical research. This paper provides practical guidelines for implementing strict and reproducible quality control for acupuncture randomized controlled trials (RCTs). Methods A standard quality control program (QCP) was established to monitor the quality of acupuncture trials. Case report forms were designed; qualified investigators, study personnel and data management personnel were trained. Monitors, who were directly appointed by the project leader, completed the quality control programs. They guaranteed data accuracy and prevented or detected protocol violations. Clinical centers and clinicians were audited, the randomization system of the centers was inspected, and the treatment processes were audited as well. In addition, the case report forms were reviewed for completeness and internal consistency, the eligibility and validity of the patients in the study was verified, and data was monitored for compliance and accuracy. Results and discussion The monitors complete their reports and submit it to quality assurance and the sponsors. Recommendations and suggestions are made for improving performance. By holding regular meetings to discuss improvements in monitoring standards, the monitors can improve quality and efficiency. Conclusions Supplementing and improving the existed guidelines for quality monitoring will ensure that large multi-centre acupuncture clinical trials will be considered as valid and scientifically stringent as pharmaceutical clinical trials. It will also develop academic excellence and further promote the international recognition of acupuncture. PMID:20035630

Quality status display for a vibration welding process

DOEpatents

Spicer, John Patrick; Abell, Jeffrey A.; Wincek, Michael Anthony; Chakraborty, Debejyo; Bracey, Jennifer; Wang, Hui; Tavora, Peter W.; Davis, Jeffrey S.; Hutchinson, Daniel C.; Reardon, Ronald L.; Utz, Shawn

2017-03-28

A system includes a host machine and a status projector. The host machine is in electrical communication with a collection of sensors and with a welding controller that generates control signals for controlling the welding horn. The host machine is configured to execute a method to thereby process the sensory and control signals, as well as predict a quality status of a weld that is formed using the welding horn, including identifying any suspect welds. The host machine then activates the status projector to illuminate the suspect welds. This may occur directly on the welds using a laser projector, or on a surface of the work piece in proximity to the welds. The system and method may be used in the ultrasonic welding of battery tabs of a multi-cell battery pack in a particular embodiment. The welding horn and welding controller may also be part of the system.

Using spacecraft trace contaminant control systems to cure sick building syndrome

NASA Technical Reports Server (NTRS)

Graf, John C.

1994-01-01

Many residential and commercial buildings with centralized, recirculating, heating ventilation and air conditioning systems suffer from 'Sick Building Syndrome.' Ventilation rates are reduced to save energy costs, synthetic building materials off-gas contaminants, and unsafe levels of volatile organic compounds (VOC's) accumulate. These unsafe levels of contaminants can cause irritation of eyes and throat, fatigue and dizziness to building occupants. Increased ventilation, the primary method of treating Sick Building Syndrome is expensive (due to increased energy costs) and recently, the effectiveness of increased ventilation has been questioned. On spacecraft venting is not allowed, so the primary methods of air quality control are; source control, active filtering, and destruction of VOC's. Four non-venting contaminant removal technologies; strict material selection to provide source control, ambient temperature catalytic oxidation, photocatalytic oxidation, and uptake by higher plants, may have potential application for indoor air quality control.

Comprehensive analysis of chemical constituents in Xingxiong injection by high performance liquid chromatography coupled with mass spectrometry.

PubMed

Guo, Long; Dou, Li-Li; Duan, Li; Liu, Ke; Bi, Zhi-Ming; Li, Ping; Liu, E-Hu

2015-09-01

Xingxiong injection (XXI) is a widely used Chinese herbal formula prepared by the folium ginkgo extract and ligustrazine for the treatment of cardiovascular and cerebrovascular diseases. Compared with the pharmacological studies, chemical analysis and quality control studies on this formula are relatively limited. In the present study, a high performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (HPLC-QTOF MS) method was applied to comprehensive analysis of constituents in XXI. According to the fragmentation rules and previous reports, thirty ginkgo flavonoids, four ginkgo terpene lactones, and one alkaloid were identified. A high performance liquid chromatography coupled with triple quadrupole mass spectrometry (HPLC-QQQ MS) method was then applied to quantify ten major constituents in XXI. The method validation results indicated that the developed method had desirable specificity, linearity, precision and accuracy. The total contents of ginkgo flavonoids were about 22.05-25.51 μg·mL(-1) and the ginkgo terpene lactones amounts were about 4.41-8.70 μg·mL(-1) in six batches of XXI samples, respectively. Furthermore, cosine ratio algorithm and distance measurements were employed to evaluate the similarity of XXI samples, and the results demonstrated a high-quality consistency. This work could provide comprehensive information on the quality control of Xingxiong injection, which be helpful in the establishment of a rational quality control standard. Copyright © 2015 China Pharmaceutical University. Published by Elsevier B.V. All rights reserved.

Human Connectome Project Informatics: quality control, database services, and data visualization

PubMed Central

Marcus, Daniel S.; Harms, Michael P.; Snyder, Abraham Z.; Jenkinson, Mark; Wilson, J Anthony; Glasser, Matthew F.; Barch, Deanna M.; Archie, Kevin A.; Burgess, Gregory C.; Ramaratnam, Mohana; Hodge, Michael; Horton, William; Herrick, Rick; Olsen, Timothy; McKay, Michael; House, Matthew; Hileman, Michael; Reid, Erin; Harwell, John; Coalson, Timothy; Schindler, Jon; Elam, Jennifer S.; Curtiss, Sandra W.; Van Essen, David C.

2013-01-01

The Human Connectome Project (HCP) has developed protocols, standard operating and quality control procedures, and a suite of informatics tools to enable high throughput data collection, data sharing, automated data processing and analysis, and data mining and visualization. Quality control procedures include methods to maintain data collection consistency over time, to measure head motion, and to establish quantitative modality-specific overall quality assessments. Database services developed as customizations of the XNAT imaging informatics platform support both internal daily operations and open access data sharing. The Connectome Workbench visualization environment enables user interaction with HCP data and is increasingly integrated with the HCP's database services. Here we describe the current state of these procedures and tools and their application in the ongoing HCP study. PMID:23707591

On quality control procedures for solar radiation and meteorological measures, from subhourly to montly average time periods

NASA Astrophysics Data System (ADS)

Espinar, B.; Blanc, P.; Wald, L.; Hoyer-Klick, C.; Schroedter-Homscheidt, M.; Wanderer, T.

2012-04-01

Meteorological data measured by ground stations are often a key element in the development and validation of methods exploiting satellite images. These data are considered as a reference against which satellite-derived estimates are compared. Long-term radiation and meteorological measurements are available from a large number of measuring stations. However, close examination of the data often reveals a lack of quality, often for extended periods of time. This lack of quality has been the reason, in many cases, of the rejection of large amount of available data. The quality data must be checked before their use in order to guarantee the inputs for the methods used in modelling, monitoring, forecast, etc. To control their quality, data should be submitted to several conditions or tests. After this checking, data that are not flagged by any of the test is released as a plausible data. In this work, it has been performed a bibliographical research of quality control tests for the common meteorological variables (ambient temperature, relative humidity and wind speed) and for the usual solar radiometrical variables (horizontal global and diffuse components of the solar radiation and the beam normal component). The different tests have been grouped according to the variable and the average time period (sub-hourly, hourly, daily and monthly averages). The quality test may be classified as follows: • Range checks: test that verify values are within a specific range. There are two types of range checks, those based on extrema and those based on rare observations. • Step check: test aimed at detecting unrealistic jumps or stagnation in the time series. • Consistency checks: test that verify the relationship between two or more time series. The gathered quality tests are applicable for all latitudes as they have not been optimized regionally nor seasonably with the aim of being generic. They have been applied to ground measurements in several geographic locations, what result in the detection of some control tests that are no longer adequate, due to different reasons. After the modification of some test, based in our experience, a set of quality control tests is now presented, updated according to technology advances and classified. The presented set of quality tests allows radiation and meteorological data to be tested in order to know their plausibility to be used as inputs in theoretical or empirical methods for scientific research. The research leading to those results has partly receive funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under Grant Agreement no. 262892 (ENDORSE project).

The vaccines consistency approach project: an EPAA initiative.

PubMed

De Mattia, F; Hendriksen, C; Buchheit, K H; Chapsal, J M; Halder, M; Lambrigts, D; Redhead, K; Rommel, E; Scharton-Kersten, T; Sesardic, T; Viviani, L; Ragan, I

2015-01-01

The consistency approach for release testing of established vaccines promotes the use of in vitro, analytical, non-animal based systems allowing the monitoring of quality parameters during the whole production process. By using highly sensitive non-animal methods, the consistency approach has the potential to improve the quality of testing and to foster the 3Rs (replacement, refinement and reduction of animal use) for quality control of established vaccines. This concept offers an alternative to the current quality control strategy which often requires large numbers of laboratory animals. In order to facilitate the introduction of the consistency approach for established human and veterinary vaccine quality control, the European Partnership for Alternatives to Animal Testing (EPAA) initiated a project, the "Vaccines Consistency Approach Project", aiming at developing and validating the consistency approach with stakeholders from academia, regulators, OMCLs, EDQM, European Commission and industry. This report summarises progress since the project's inception.

Development of Process Analytical Technology (PAT) methods for controlled release pellet coating.

PubMed

Avalle, P; Pollitt, M J; Bradley, K; Cooper, B; Pearce, G; Djemai, A; Fitzpatrick, S

2014-07-01

This work focused on the control of the manufacturing process for a controlled release (CR) pellet product, within a Quality by Design (QbD) framework. The manufacturing process was Wurster coating: firstly layering active pharmaceutical ingredient (API) onto sugar pellet cores and secondly a controlled release (CR) coating. For each of these two steps, development of a Process Analytical Technology (PAT) method is discussed and also a novel application of automated microscopy as the reference method. Ultimately, PAT methods should link to product performance and the two key Critical Quality Attributes (CQAs) for this CR product are assay and release rate, linked to the API and CR coating steps respectively. In this work, the link between near infra-red (NIR) spectra and those attributes was explored by chemometrics over the course of the coating process in a pilot scale industrial environment. Correlations were built between the NIR spectra and coating weight (for API amount), CR coating thickness and dissolution performance. These correlations allow the coating process to be monitored at-line and so better control of the product performance in line with QbD requirements. Copyright © 2014 Elsevier B.V. All rights reserved.

Substation Reactive Power Regulation Strategy

NASA Astrophysics Data System (ADS)

Zhang, Junfeng; Zhang, Chunwang; Ma, Daqing

2018-01-01

With the increasing requirements on the power supply quality and reliability of distribution network, voltage and reactive power regulation of substations has become one of the indispensable ways to ensure voltage quality and reactive power balance and to improve the economy and reliability of distribution network. Therefore, it is a general concern of the current power workers and operators that what kind of flexible and effective control method should be used to adjust the on-load tap-changer (OLTC) transformer and shunt compensation capacitor in a substation to achieve reactive power balance in situ, improve voltage pass rate, increase power factor and reduce active power loss. In this paper, based on the traditional nine-zone diagram and combining with the characteristics of substation, a fuzzy variable-center nine-zone diagram control method is proposed and used to make a comprehensive regulation of substation voltage and reactive power. Through the calculation and simulation of the example, this method is proved to have satisfactorily reconciled the contradiction between reactive power and voltage in real-time control and achieved the basic goal of real-time control of the substation, providing a reference value to the practical application of the substation real-time control method.

Groundwater-quality and quality-control data for two monitoring wells near Pavillion, Wyoming, April and May 2012

USGS Publications Warehouse

Wright, Peter R.; McMahon, Peter B.; Mueller, David K.; Clark, Melanie L.

2012-01-01

In June 2010, the U.S. Environmental Protection Agency installed two deep monitoring wells (MW01 and MW02) near Pavillion, Wyoming, to study groundwater quality. During April and May 2012, the U.S Geological Survey, in cooperation with the Wyoming Department of Environmental Quality, collected groundwater-quality data and quality-control data from monitoring well MW01 and, following well redevelopment, quality-control data for monitoring well MW02. Two groundwater-quality samples were collected from well MW01—one sample was collected after purging about 1.5 borehole volumes, and a second sample was collected after purging 3 borehole volumes. Both samples were collected and processed using methods designed to minimize atmospheric contamination or changes to water chemistry. Groundwater-quality samples were analyzed for field water-quality properties (water temperature, pH, specific conductance, dissolved oxygen, oxidation potential); inorganic constituents including naturally occurring radioactive compounds (radon, radium-226 and radium-228); organic constituents; dissolved gasses; stable isotopes of methane, water, and dissolved inorganic carbon; and environmental tracers (carbon-14, chlorofluorocarbons, sulfur hexafluoride, tritium, helium, neon, argon, krypton, xenon, and the ratio of helium-3 to helium-4). Quality-control sample results associated with well MW01 were evaluated to determine the extent to which environmental sample analytical results were affected by bias and to evaluate the variability inherent to sample collection and laboratory analyses. Field documentation, environmental data, and quality-control data for activities that occurred at the two monitoring wells during April and May 2012 are presented.

A Method to Quantify the Wind and Non-wind Contribution to Year-to-year Air Quality Variation and its Application in China

NASA Astrophysics Data System (ADS)

LI, Y.; Lau, A. K. H.; Wong, A.; Fung, J. C. H.

2017-12-01

Changes in emissions and wind are often identified as the two dominant factors contributing to year-to-year variations in the concentration of primary pollutants. However, because changes in wind and emissions are intertwined, it has been difficult to quantitatively differentiate their effects on air quality directly from observed data. In particular, if the annual mean concentration of pollutants is higher than the previous year, it is difficult to identify whether the deterioration in air quality is caused by wind blowing from more polluted regions or an increase in contributing emissions. In this paper, based on wind and pollution roses, we propose a method to differentiate the effects of wind and non-wind (e.g., emissions) changes using direct observation. An index (L) is first defined to quantify the validity of the linear decomposition. The method is then validated by idealized experiments, numerical experiments and a two-year observation dataset from an actual emissions control program. Finally, we demonstrate the proposed method by studying long-term PM10 variations in Hong Kong during 2000-2011. We find that for most of the period, the linear decomposition of the changes in annual PM10 is valid (up to 90% confidence) and is dominated by the change in non-wind effects (e.g., emissions), whereas the average absolute effect from the wind variability is about 20%. Sensitivity analyses also suggest that our method should work in any location as long as the observed wind and pollution data have sufficient duration and resolution to resolve the corresponding wind and pollution roses. The method is applied for estimating the control effectiveness of the intervention programs in the Shanghai Expo, the longest socioeconomic international event held in China. The results show that integrated effect of control policies taken for improving the air quality in Shanghai are significantly effective for PM10 reduction and also effective for SO2 reduction, whereas the traffic emission control are not effective for NO2 at urban stations, though the overall emission control lead to an decrease for the city average NO2 concentration.

Controlling coarse woody debris inventory quality: taper and relative size methods

Treesearch

C.W. Woodall; J.A. Westfall

2008-01-01

Accurately measuring the dimensions of coarse woody debris (CWD) is critical for ensuring the quality of CWD estimates and, hence, for accurately estimating forest ecosystem attributes (e.g., CWD carbon stocks). To improve the quality of CWD dimensional measurements, the distribution of taper (ratio of change in diameter and length) and relative size (RS; ratio of...

[Study on the optimization of monitoring indicators of drinking water quality during health supervision].

PubMed

Ye, Bixiong; E, Xueli; Zhang, Lan

2015-01-01

To optimize non-regular drinking water quality indices (except Giardia and Cryptosporidium) of urban drinking water. Several methods including drinking water quality exceed the standard, the risk of exceeding standard, the frequency of detecting concentrations below the detection limit, water quality comprehensive index evaluation method, and attribute reduction algorithm of rough set theory were applied, redundancy factor of water quality indicators were eliminated, control factors that play a leading role in drinking water safety were found. Optimization results showed in 62 unconventional water quality monitoring indicators of urban drinking water, 42 water quality indicators could be optimized reduction by comprehensively evaluation combined with attribute reduction of rough set. Optimization of the water quality monitoring indicators and reduction of monitoring indicators and monitoring frequency could ensure the safety of drinking water quality while lowering monitoring costs and reducing monitoring pressure of the sanitation supervision departments.

[Establishment of Quality Control System of Nucleic Acid Detection for Ebola Virus in Sierra Leone-China Friendship Biological Safety Laboratory].

PubMed

Wang, Qin; Zhang, Yong; Nie, Kai; Wang, Huanyu; Du, Haijun; Song, Jingdong; Xiao, Kang; Lei, Wenwen; Guo, Jianqiang; Wei, Hejiang; Cai, Kun; Wang, Yanhai; Wu, Jiang; Gerald, Bangura; Kamara, Idrissa Laybohr; Liang, Mifang; Wu, Guizhen; Dong, Xiaoping

2016-03-01

The quality control process throughout the Ebola virus nucleic acid detection in Sierra Leone-China Friendship Biological Safety Laboratory (SLE-CHN Biosafety Lab) was described in detail, in order to comprehensively display the scientific, rigorous, accurate and efficient practice in detection of Ebola virus of first batch detection team in SLE-CHN Biosafety Lab. Firstly, the key points of laboratory quality control system was described, including the managements and organizing, quality control documents and information management, instrument, reagents and supplies, assessment, facilities design and space allocation, laboratory maintenance and biosecurity. Secondly, the application of quality control methods in the whole process of the Ebola virus detection, including before the test, during the test and after the test, was analyzed. The excellent and professional laboratory staffs, the implementation of humanized management are the cornerstone of the success; High-level biological safety protection is the premise for effective quality control and completion of Ebola virus detection tasks. And professional logistics is prerequisite for launching the laboratory diagnosis of Ebola virus. The establishment and running of SLE-CHN Biosafety Lab has landmark significance for the friendship between Sierra Leone and China, and the lab becomes the most important base for Ebola virus laboratory testing in Sierra Leone.

Headache-specific locus of control and migraine-related quality of life: understanding the role of anxiety

PubMed Central

Grinberg, Amy S.; Seng, Elizabeth K.

2017-01-01

Purpose This study examined the relationship between headache-specific locus of control (HSLC) and migraine-related quality of life, and anxiety as a mediator of this relationship. Methods Two hundred and thirty-two people with severe migraine participated in the Treatment of Severe Migraine trial. At baseline, participants completed self-report questionnaires of headache-specific locus of control (HSLC; subscales = Internal, Chance, and Medical Professionals), anxiety, and migraine-related quality of life. Correlations examined relationships between HSLC, anxiety, and migraine-related quality of life; ordinary least squares regression evaluated anxiety as a mediator of the relationship between HSLC and migraine-related quality of life. Results Higher internal HSLC was related to higher overall migraine-related quality of life (ps < .05) and emotion function impairments (p = .012). Anxiety mediated the relationship between internal HSLC and all measures of migraine-specific quality of life (ps < .05). Higher external (medical professionals and chance) HSLC was related to higher migraine-related quality of life impairments (all ps < .001). Conclusions All HSLC beliefs are associated with higher migraine-related quality of life impairments. Anxiety mediates the relationship between internal HSLC and migraine-related quality of life. PMID:27488417

Integrity management of offshore structures and its implication on computation of structural action effects and resistance

NASA Astrophysics Data System (ADS)

Moan, T.

2017-12-01

An overview of integrity management of offshore structures, with emphasis on the oil and gas energy sector, is given. Based on relevant accident experiences and means to control the associated risks, accidents are categorized from a technical-physical as well as human and organizational point of view. Structural risk relates to extreme actions as well as structural degradation. Risk mitigation measures, including adequate design criteria, inspection, repair and maintenance as well as quality assurance and control of engineering processes, are briefly outlined. The current status of risk and reliability methodology to aid decisions in the integrity management is briefly reviewed. Finally, the need to balance the uncertainties in data, methods and computational efforts and the cautious use and quality assurance and control in applying high fidelity methods to avoid human errors, is emphasized, and with a plea to develop both high fidelity as well as efficient, simplified methods for design.

Looking beyond patients: Can parents' quality of life predict asthma control in children?

PubMed

Cano-Garcinuño, Alfredo; Mora-Gandarillas, Isabel; Bercedo-Sanz, Alberto; Callén-Blecua, María Teresa; Castillo-Laita, José Antonio; Casares-Alonso, Irene; Forns-Serrallonga, Dolors; Tauler-Toro, Eulàlia; Alonso-Bernardo, Luz María; García-Merino, Águeda; Moneo-Hernández, Isabel; Cortés-Rico, Olga; Carvajal-Urueña, Ignacio; Morell-Bernabé, Juan José; Martín-Ibáñez, Itziar; Rodríguez-Fernández-Oliva, Carmen Rosa; Asensi-Monzó, María Teresa; Fernández-Carazo, Carmen; Murcia-García, José; Durán-Iglesias, Catalina; Montón-Álvarez, José Luis; Domínguez-Aurrecoechea, Begoña; Praena-Crespo, Manuel

2016-07-01

Social and family factors may influence the probability of achieving asthma control in children. Parents' quality of life has been insufficiently explored as a predictive factor linked to the probability of achieving disease control in asthmatic children. Determine whether the parents' quality of life predicts medium-term asthma control in children. Longitudinal study of children between 4 and 14 years of age, with active asthma. The parents' quality of life was evaluated using the specific IFABI-R instrument, in which scores were higher for poorer quality of life. Its association with asthma control measures in the child 16 weeks later was analyzed using multivariate methods, adjusting the effect for disease, child and family factors. The data from 452 children were analyzed (median age 9.6 years, 63.3% males). The parents' quality of life was predictive for asthma control; each point increase on the initial IFABI-R score was associated with an adjusted odds ratio (95% confidence interval) of 0.56 (0.37-0.86) for good control of asthma on the second visit, 2.58 (1.62-4.12) for asthma exacerbation, 2.12 (1.33-3.38) for an unscheduled visit to the doctor, and 2.46 (1.18-5.13) for going to the emergency room. The highest quartile for the IFABI-R score had a sensitivity of 34.5% and a specificity of 82.2% to predict poorly controlled asthma. Parents' poorer quality of life is related to poor, medium-term asthma control in children. Assessing the parents' quality of life could aid disease management decisions. Pediatr Pulmonol. 2016;51:670-677. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

NONDESTRUCTIVE QUALITY CONTROL: SOME SPECIAL METHODS OF IRRADIATION TESTING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van der Klis, T.

1961-06-10

S>Various methods, using open radioactive sources are discussed. In one method, oil is used containing Pd/sup 109/ which is adsorbed by Mg compounds with which the object to be tested is covered after it has been enveloped in a photographic film. Another method consists of coking the material in the radioactive oil and then scanning it with a suitable detector. A third method, applied especially to porous materials, uses pressure to promote the penetration of the radioactive oil into the cracks and fissures. The filtered particle technique is also used for detection of cracks or cavities in porous materials, suchmore » as ceramics, cement, graphite pressed powdered metals, and sintered carbides. In this method, radioactive liquids are used along with fluid fluorescent substances. Finally, a method is mentioned in which radioactive powder is made to adhere to the surface of the investigated objects by means of an electrostatic charge. This method is used for quality control of china, glass, email, and electric insulation material. (OID)« less

Design and Establishment of Quality Model of Fundamental Geographic Information Database

NASA Astrophysics Data System (ADS)

Ma, W.; Zhang, J.; Zhao, Y.; Zhang, P.; Dang, Y.; Zhao, T.

2018-04-01

In order to make the quality evaluation for the Fundamental Geographic Information Databases(FGIDB) more comprehensive, objective and accurate, this paper studies and establishes a quality model of FGIDB, which formed by the standardization of database construction and quality control, the conformity of data set quality and the functionality of database management system, and also designs the overall principles, contents and methods of the quality evaluation for FGIDB, providing the basis and reference for carry out quality control and quality evaluation for FGIDB. This paper designs the quality elements, evaluation items and properties of the Fundamental Geographic Information Database gradually based on the quality model framework. Connected organically, these quality elements and evaluation items constitute the quality model of the Fundamental Geographic Information Database. This model is the foundation for the quality demand stipulation and quality evaluation of the Fundamental Geographic Information Database, and is of great significance on the quality assurance in the design and development stage, the demand formulation in the testing evaluation stage, and the standard system construction for quality evaluation technology of the Fundamental Geographic Information Database.

Using magnetic levitation for non-destructive quality control of plastic parts.

PubMed

Hennek, Jonathan W; Nemiroski, Alex; Subramaniam, Anand Bala; Bwambok, David K; Yang, Dian; Harburg, Daniel V; Tricard, Simon; Ellerbee, Audrey K; Whitesides, George M

2015-03-04

Magnetic levitation (MagLev) enables rapid and non-destructive quality control of plastic parts. The feasibility of MagLev as a method to: i) rapidly assess injection-molded plastic parts for defects during process optimization, ii) monitor the degradation of plastics after exposure to harsh environmental conditions, and iii) detect counterfeit polymers by density is demonstrated. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Use of the MS2 automated system in the determination of the activity of 5 antiseptic drugs: quality control].

PubMed

Vincent, F; Guyomard, S; Goury, V; Darbord, J C

1987-06-01

The study of growth curves of Klebsiella pneumoniae and Staphylococcus aureus in presence of five antiseptics, established using a MS2 Abbott system is presented. From our results, the advantages of automation after the adaptation of the method for the determination of bactericidal properties are examined. This technique may be proposed for the quality control of such drugs.

Mechanical and Acoustic Characteristics of the Weld and the Base Metal Machine Part of Career Transport

NASA Astrophysics Data System (ADS)

Smirnov, Alexander N.; Knjaz'kov, Victor L.; Levashova, Elena E.; Ababkov, Nikolay V.; Pimonov, Maksim V.

2018-01-01

Currently, many industries use foreign-made machinery. There is no opportunity to purchase quality original spare parts for which machinery. Therefore, enterprises operating this equipment are looking for producers of analogues of various parts and assemblies. Quite often, the metal of such analog components turns out to be substandard, which leads to their breakdown at a much earlier date and the enterprises incur material losses. Due to the fact that the complex of performance characteristics and the resource of products are laid at the stage of their production, it is extremely important to control the quality of the raw materials. The structure, mechanical, acoustic and magnetic characteristics of metal samples of such destroyed details of quarry transport as hydraulic cylinders and detail “axis” of an excavator are investigated. A significant spread of data on the chemical composition of metal, hardness and characteristics of non-destructive testing is established, which gives grounds to recommend to manufacturers and suppliers of parts is more responsible to approach the incoming quality control. The results of the investigation of metal samples by destructive and non-destructive methods of control are compared, which showed that the spectral-acoustic method of nondestructive testing can be used to control the quality of the responsible machine parts under conditions of import substitution.

A Simple and Rapid UPLC-PDA Method for Quality Control of Nardostachys jatamansi.

PubMed

Zhang, Weize; Nan, Guo; Wu, Hong-Hua; Jiang, Miaomiao; Li, Tian-Xiang; Wang, Meng; Gao, Xiu-Mei; Zhu, Yan; Song, Yun Seon; Wang, Jiaming; Xu, Yan-Tong

2018-05-01

Nardostachys jatamansi is a well-documented herbal agent used to treat digestive and neuropsychiatric disorders in oriental medicinal systems. However, few simple, rapid, and comprehensive methods were reported for quality assessment and control of N. jatamansi . Herein, a UPLC with photodiode array detection method was developed for both fingerprint investigation of N. jatamansi and simultaneous quantitative analysis of the six serotonin transporter modulatory constituents in N. jatamansi . For chromatographic fingerprinting, 24 common peaks were selected as characteristic peaks to assess the consistency of N. jatamansi samples from different retail sources. Six of the common peaks (5, 7, 12: , and 16:  - 18: ) were identified as desoxo-narchinol A, buddleoside, isonardosinone, nardosinone, kanshone H, and (-)-aristolone, respectively, by phytochemical investigation. Five of the six compounds significantly either enhanced or inhibited serotonin transporter activity, while (-)-aristolone (18: ) didn't show any serotonin transporter activity. In quantitative analysis, the six compounds showed good linearity ( r  > 0.999) within test ranges. The precision, expressed as relative standard deviation, was in the range of 0.25 - 2.77%, and the recovery of the method was in the range of 92 - 105%. The UPLC-photodiode array detection-based fingerprint analysis and quantitative methods reported here could be used for routine quality control of N. jatamansi . Georg Thieme Verlag KG Stuttgart · New York.

Topographic and hydrographic survey data for the São Francisco River near Torrinha, Bahia, Brazil, 2014

USGS Publications Warehouse

Fosness, Ryan L.; Dietsch, Benjamin J.

2015-10-21

This report presents the surveying techniques and data-processing methods used to collect, process, and disseminate topographic and hydrographic data. All standard and non‑standard data-collection methods, techniques, and data process methods were documented. Additional discussion describes the quality-assurance and quality-control elements used in this study, along with the limitations for the Torrinha-Itacoatiara study reach data. The topographic and hydrographic geospatial data are published along with associated metadata.

Quality controls in cellular immunotherapies: rapid assessment of clinical grade dendritic cells by gene expression profiling.

PubMed

Castiello, Luciano; Sabatino, Marianna; Zhao, Yingdong; Tumaini, Barbara; Ren, Jiaqiang; Ping, Jin; Wang, Ena; Wood, Lauren V; Marincola, Francesco M; Puri, Raj K; Stroncek, David F

2013-02-01

Cell-based immunotherapies are among the most promising approaches for developing effective and targeted immune response. However, their clinical usefulness and the evaluation of their efficacy rely heavily on complex quality control assessment. Therefore, rapid systematic methods are urgently needed for the in-depth characterization of relevant factors affecting newly developed cell product consistency and the identification of reliable markers for quality control. Using dendritic cells (DCs) as a model, we present a strategy to comprehensively characterize manufactured cellular products in order to define factors affecting their variability, quality and function. After generating clinical grade human monocyte-derived mature DCs (mDCs), we tested by gene expression profiling the degrees of product consistency related to the manufacturing process and variability due to intra- and interdonor factors, and how each factor affects single gene variation. Then, by calculating for each gene an index of variation we selected candidate markers for identity testing, and defined a set of genes that may be useful comparability and potency markers. Subsequently, we confirmed the observed gene index of variation in a larger clinical data set. In conclusion, using high-throughput technology we developed a method for the characterization of cellular therapies and the discovery of novel candidate quality assurance markers.

Development of Methodology and Technology for Identifying and Quantifying Emission Products from Open Burning and Open Detonation Thermal Treatment Methods. Field Test Series A, B, and C. Volume 2, Part B. Quality Assurance and Quality Control. Appendices

DTIC Science & Technology

1992-01-01

the uncertainty. The above method can give an estimate of the precision of the * analysis. However, determining the accuracy can not be done as...speciation has been determined from analyzing model samples as well as comparison with other methods and combinations of other methods with this method . 3...laboratory. The output of the sensor is characterized over its working range and an appropriate response factor determined by linear regression of the

A multi-factor designation method for mapping particulate-pollution control zones in China.

PubMed

Qin, Y; Xie, S D

2011-09-01

A multi-factor designation method for mapping particulate-pollution control zones was brought out through synthetically considering PM(10) pollution status, PM(10) anthropogenic emissions, fine particle pollution, long-range transport and economic situation. According to this method, China was divided into four different particulate-pollution control regions: PM Suspended Control Region, PM(10) Pollution Control Region, PM(2.5) Pollution Control Region and PM(10) and PM(2.5) Common Control Region, which accounted for 69.55%, 9.66%, 4.67% and 16.13% of China's territory, respectively. The PM(10) and PM(2.5) Common Control Region was mainly distributed in Bohai Region, Yangtze River Delta, Pearl River Delta, eastern of Sichuan province and Chongqing municipality, calling for immediate control of both PM(10) and PM(2.5). Cost-effective control effects can be achieved through concentrating efforts on PM(10) and PM(2.5) Common Control Region to address 60.32% of national PM(10) anthropogenic emissions. Air quality in districts belonging to PM(2.5) Pollution Control Region suggested that Chinese national ambient air quality standard for PM(10) was not strict enough. The result derived from application to China proved that this approach was feasible for mapping pollution control regions for a country with vast territory, complicated pollution characteristics and limited available monitoring data. Copyright © 2011 Elsevier B.V. All rights reserved.

[Application of microscopic spectroscopy in quality control of Niuhuang Qingxin pills].

PubMed

Nie, Li-Xing; Zhang, Ye; Zhang, Nan-Ping; Hu, Xiao-Ru; Kang, Shuai; Hou, Jian-Zhong; Dai, Zhong; Ma, Shuang-Cheng

2016-10-01

Application of microscopic spectroscopy in quality control of Niuhuang Qingxin pills was discussed. First, microscopic characteristics specified by the statutory standard of Niuhuang Qingxin pills were summarized. Then new identification method was established for Dioscoreae Rhizoma, Saigae Tataricae Cornu, Cinnamomi Cortex and Saposhnikoviae Radix. Finally, microscopic spectroscopy was used for test of Dioscoreae Rhizoma's adulterant Dioscoreae Fordii Rhizoma.It was the first time for this technology being applied in adulteration test of Chinese patent medicine.The results showed that Saigae Tataricae Cornu was not detected in 2 batches of Niuhuang Qingxin pills from 1 manufacturer while Dioscoreae Fordii Rhizoma was detected in 3 batches of samples from 2 manufacturers. The proposed methods were accurate, simple, rapid, objective and economic, which offered a more comprehensive approach for quality control of Niuhuang Qingxin pills. It was indicated that conventional technology such as microscopic spectroscopy could play an important role in identification of traditional Chinese medicine whose index ingredient was deficient or tiny. Copyright© by the Chinese Pharmaceutical Association.

MALDI-TOF MS for quality control of high protein content sport supplements.

PubMed

De Ceglie, Cristina; Calvano, Cosima D; Zambonin, Carlo G

2015-06-01

High protein content sport nutritional supplements are found as powder products containing, as ingredients, amino acids and proteins with important nutritional values as milk, soy and egg proteins. An EU Food Supplements Directive (2002) requires that supplements should be safe, both in dosages and in purity. It is important, then, to develop rapid and sensitive methods to be employed for the quality control of these substances. In this work, we apply, for the first time, matrix-assisted laser desorption ionization-mass spectrometry as a fast, reproducible and sensitive method for the quality control of sport nutritional supplements based on proteins. To this aim, several commercial egg- and/or milk-based powder products have been processed by in gel or in solution digestion and analyzed in comparison to pure standard products. This strategy allowed to assess the reliability of the indications on proteins (as caseins, whey proteins and ovalbumin) declared in the label of several sport nutritional supplements. Copyright © 2014 Elsevier Ltd. All rights reserved.

Develop nondestructive rapid pavement quality assurance/quality control evaluation test methods and supporting technology : project summary.

DOT National Transportation Integrated Search

2017-01-01

The findings from the proof of concept with mechanics-based models for flexible base suggest additional validation work should be performed, draft construction specification frameworks should be developed, and work extending the technology to stabili...

A spectral method for spatial downscaling

EPA Science Inventory

Complex computer models play a crucial role in air quality research. These models are used to evaluate potential regulatory impacts of emission control strategies and to estimate air quality in areas without monitoring data. For both of these purposes, it is important to calibrat...

Develop nondestructive rapid pavement quality Assurance/quality control evaluation test methods and supporting technology : project summary.

DOT National Transportation Integrated Search

2017-01-01

The findings from the proof of concept with mechanics-based models for flexible base suggest additional validation work should be performed, draft construction specification frameworks should be developed, and work extending the technology to stabili...

CTEPP STANDARD OPERATING PROCEDURE FOR DETECTION AND QUANTIFICATION OF TARGET ANALYTES BY GAS CHROMATOGRAPHY/MASS SPECTROMETRY (GC/MS) (SOP-5.24)

EPA Science Inventory

This standard operating procedure describes the method used for the determination of target analytes in sample extracts and related quality assurance/quality control sample extracts generated in the CTEPP study.

The effects of a team-based continuous quality improvement intervention on the management of primary care: a randomised controlled trial

PubMed Central

Engels, Yvonne; van den Hombergh, Pieter; Mokkink, Henk; van den Hoogen, Henk; van den Bosch, Wil; Grol, Richard

2006-01-01

Aim To study the effects of a team-based model for continuous quality improvement (CQI) on primary care practice management. Design of study Randomised controlled trial. Setting Twenty-six intervention and 23 control primary care practices in the Netherlands. Method Practices interested in taking part in the CQI project were, after assessment of their practice organisation, randomly assigned to the intervention or control groups. During a total of five meetings, a facilitator helped the teams in the intervention group select suitable topics for quality improvement and follow a structured approach to achieve improvement objectives. Checklists completed by an outreach visitor, questionnaires for the GPs, staff and patients were used to assemble data on the number and quality of improvement activities undertaken and on practice management prior to the start of the intervention and 1 year later. Results Pre-test and post-test data were compared for the 26 intervention and 23 control practices. A significant intervention effect was found for the number of improvement objectives actually defined (93 versus 54, P<0.001) and successfully completed (80 versus 69% of the projects, P<0.001). The intervention group also improved on more aspects of practice management, as measured by our practice visit method, than the control group but none of these differences proved statistically significant. Conclusion The intervention exerted a significant effect on the number and quality of improvement projects undertaken and self-defined objectives met. Failure of the effects of the intervention on the other dimensions of practice management to achieve significance may be due to the topics selected for some of the improvement projects being only partly covered by the assessment instrument. PMID:17007709

Colorimetry as Quality Control Tool for Individual Inkjet-Printed Pediatric Formulations.

PubMed

Wickström, Henrika; Nyman, Johan O; Indola, Mathias; Sundelin, Heidi; Kronberg, Leif; Preis, Maren; Rantanen, Jukka; Sandler, Niklas

2017-02-01

Printing technologies were recently introduced to the pharmaceutical field for manufacturing of drug delivery systems. Printing allows on demand manufacturing of flexible pharmaceutical doses in a personalized manner, which is critical for a successful and safe treatment of patient populations with specific needs, such as children and the elderly, and patients facing multimorbidity. Printing of pharmaceuticals as technique generates new demands on the quality control procedures. For example, rapid quality control is needed as the printing can be done on demand and at the point of care. This study evaluated the potential use of a handheld colorimetry device for quality control of printed doses of vitamin Bs on edible rice and sugar substrates. The structural features of the substrates with and without ink were also compared. A multicomponent ink formulation with vitamin B 1 , B 2 , B 3 , and B 6 was developed. Doses (4 cm 2 ) were prepared by applying 1-10 layers of yellow ink onto the white substrates using thermal inkjet technology. The colorimetric method was seen to be viable in detecting doses up to the 5th and 6th printed layers until color saturation of the yellow color parameter (b*) was observed on the substrates. Liquid chromatography mass spectrometry was used as a reference method for the colorimetry measurements plotted against the number of printed layers. It was concluded that colorimetry could be used as a quality control tool for detection of different doses. However, optimization of the color addition needs to be done to avoid color saturation within the planned dose interval.

Simple, Low-Cost Data Collection Methods for Agricultural Field Studies.

ERIC Educational Resources Information Center

Koenig, Richard T.; Winger, Marlon; Kitchen, Boyd

2000-01-01

Summarizes relatively simple and inexpensive methods for collecting data from agricultural field studies. Describes methods involving on-farm testing, crop yield measurement, quality evaluations, weed control effectiveness, plant nutrient status, and other measures. Contains 29 references illustrating how these methods were used to conduct…

Influence of staff infection control training on infection-related quality measures in US nursing homes.

PubMed

Kaur, Jasjit; Stone, Patricia W; Travers, Jasmine L; Cohen, Catherine C; Herzig, Carolyn T A

2017-09-01

Health care-associated infections are a leading cause of morbidity and mortality in US nursing home residents. Ongoing training of nursing home staff is vital to the implementation of infection prevention and control processes. Our aim was to describe associations between methods, frequency, and timing of staff infection prevention and control training and infection-related quality measures. In this national survey of nursing homes, timing of staff infection prevention and control training was associated with reduced indwelling urinary catheter use. Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

A Strategy to Establish a Quality Assurance/Quality Control Plan for the Application of Biosensors for the Detection of E. coli in Water.

PubMed

Hesari, Nikou; Kıratlı Yılmazçoban, Nursel; Elzein, Mohamad; Alum, Absar; Abbaszadegan, Morteza

2017-01-03

Rapid bacterial detection using biosensors is a novel approach for microbiological testing applications. Validation of such methods is an obstacle in the adoption of new bio-sensing technologies for water testing. Therefore, establishing a quality assurance and quality control (QA/QC) plan is essential to demonstrate accuracy and reliability of the biosensor method for the detection of E. coli in drinking water samples. In this study, different reagents and assay conditions including temperatures, holding time, E. coli strains and concentrations, dissolving agents, salinity and pH effects, quality of substrates of various suppliers of 4-methylumbelliferyl glucuronide (MUG), and environmental water samples were included in the QA/QC plan and used in the assay optimization and documentation. Furthermore, the procedural QA/QC for the monitoring of drinking water samples was established to validate the performance of the biosensor platform for the detection of E. coli using a culture-based standard technique. Implementing the developed QA/QC plan, the same level of precision and accuracy was achieved using both the standard and the biosensor methods. The established procedural QA/QC for the biosensor will provide a reliable tool for a near real-time monitoring of E. coli in drinking water samples to both industry and regulatory authorities.

A Strategy to Establish a Quality Assurance/Quality Control Plan for the Application of Biosensors for the Detection of E. coli in Water

PubMed Central

Hesari, Nikou; Kıratlı Yılmazçoban, Nursel; Elzein, Mohamad; Alum, Absar; Abbaszadegan, Morteza

2017-01-01

Rapid bacterial detection using biosensors is a novel approach for microbiological testing applications. Validation of such methods is an obstacle in the adoption of new bio-sensing technologies for water testing. Therefore, establishing a quality assurance and quality control (QA/QC) plan is essential to demonstrate accuracy and reliability of the biosensor method for the detection of E. coli in drinking water samples. In this study, different reagents and assay conditions including temperatures, holding time, E. coli strains and concentrations, dissolving agents, salinity and pH effects, quality of substrates of various suppliers of 4-methylumbelliferyl glucuronide (MUG), and environmental water samples were included in the QA/QC plan and used in the assay optimization and documentation. Furthermore, the procedural QA/QC for the monitoring of drinking water samples was established to validate the performance of the biosensor platform for the detection of E. coli using a culture-based standard technique. Implementing the developed QA/QC plan, the same level of precision and accuracy was achieved using both the standard and the biosensor methods. The established procedural QA/QC for the biosensor will provide a reliable tool for a near real-time monitoring of E. coli in drinking water samples to both industry and regulatory authorities. PMID:28054956

A method of setting limits for the purpose of quality assurance

NASA Astrophysics Data System (ADS)

Sanghangthum, Taweap; Suriyapee, Sivalee; Kim, Gwe-Ya; Pawlicki, Todd

2013-10-01

The result from any assurance measurement needs to be checked against some limits for acceptability. There are two types of limits; those that define clinical acceptability (action limits) and those that are meant to serve as a warning that the measurement is close to the action limits (tolerance limits). Currently, there is no standard procedure to set these limits. In this work, we propose an operational procedure to set tolerance limits and action limits. The approach to establish the limits is based on techniques of quality engineering using control charts and a process capability index. The method is different for tolerance limits and action limits with action limits being categorized into those that are specified and unspecified. The procedure is to first ensure process control using the I-MR control charts. Then, the tolerance limits are set equal to the control chart limits on the I chart. Action limits are determined using the Cpm process capability index with the requirements that the process must be in-control. The limits from the proposed procedure are compared to an existing or conventional method. Four examples are investigated: two of volumetric modulated arc therapy (VMAT) point dose quality assurance (QA) and two of routine linear accelerator output QA. The tolerance limits range from about 6% larger to 9% smaller than conventional action limits for VMAT QA cases. For the linac output QA, tolerance limits are about 60% smaller than conventional action limits. The operational procedure describe in this work is based on established quality management tools and will provide a systematic guide to set up tolerance and action limits for different equipment and processes.

Quality management in in vivo proton MRS.

PubMed

Pedrosa de Barros, Nuno; Slotboom, Johannes

2017-07-15

The quality of MR-Spectroscopy data can easily be affected in in vivo applications. Several factors may produce signal artefacts, and often these are not easily detected, not even by experienced spectroscopists. Reliable and reproducible in vivo MRS-data requires the definition of quality requirements and goals, implementation of measures to guarantee quality standards, regular control of data quality, and a continuous search for quality improvement. The first part of this review includes a general introduction to different aspects of quality management in MRS. It is followed by the description of a series of tests and phantoms that can be used to assure the quality of the MR system. In the third part, several methods and strategies used for quality control of the spectroscopy data are presented. This review concludes with a reference to a few interesting techniques and aspects that may help to further improve the quality of in vivo MR-spectra. Copyright © 2017 Elsevier Inc. All rights reserved.

Comparison of volume estimation methods for pancreatic islet cells

NASA Astrophysics Data System (ADS)

Dvořák, JiřÃ.­; Å vihlík, Jan; Habart, David; Kybic, Jan

2016-03-01

In this contribution we study different methods of automatic volume estimation for pancreatic islets which can be used in the quality control step prior to the islet transplantation. The total islet volume is an important criterion in the quality control. Also, the individual islet volume distribution is interesting -- it has been indicated that smaller islets can be more effective. A 2D image of a microscopy slice containing the islets is acquired. The input of the volume estimation methods are segmented images of individual islets. The segmentation step is not discussed here. We consider simple methods of volume estimation assuming that the islets have spherical or ellipsoidal shape. We also consider a local stereological method, namely the nucleator. The nucleator does not rely on any shape assumptions and provides unbiased estimates if isotropic sections through the islets are observed. We present a simulation study comparing the performance of the volume estimation methods in different scenarios and an experimental study comparing the methods on a real dataset.

Review of Detection of Brucella sp. by Polymerase Chain Reaction

PubMed Central

Yu, Wei Ling; Nielsen, Klaus

2010-01-01

Here we present a review of most of the currently used polymerase chain reaction (PCR)-based methods for identification of Brucella bacteria in biological samples. We focused in particular on methods using single-pair primers, multiplex primers, real-time PCRs, PCRs for marine Brucella, and PCRs for molecular biotyping. These methods are becoming very important tools for the identification of Brucella, at the species level and recently also at the biovar level. These techniques require minimum biological containment and can provide results in a very short time. In addition, genetic fingerprinting of isolates aid in epidemiological studies of the disease and its control. PCR-based methods are more useful and practical than conventional methods used to identify Brucella spp., and new methods for Brucella spp identification and typing are still being developed. However, the sensitivity, specificity, and issues of quality control and quality assurance using these methods must be fully validated on clinical samples before PCR can be used in routine laboratory testing for brucellosis. PMID:20718083

Watershed safety and quality control by safety threshold method

NASA Astrophysics Data System (ADS)

Da-Wei Tsai, David; Mengjung Chou, Caroline; Ramaraj, Rameshprabu; Liu, Wen-Cheng; Honglay Chen, Paris

2014-05-01

Taiwan was warned as one of the most dangerous countries by IPCC and the World Bank. In such an exceptional and perilous island, we would like to launch the strategic research of land-use management on the catastrophe prevention and environmental protection. This study used the watershed management by "Safety Threshold Method" to restore and to prevent the disasters and pollution on island. For the deluge prevention, this study applied the restoration strategy to reduce total runoff which was equilibrium to 59.4% of the infiltration each year. For the sediment management, safety threshold management could reduce the sediment below the equilibrium of the natural sediment cycle. In the water quality issues, the best strategies exhibited the significant total load reductions of 10% in carbon (BOD5), 15% in nitrogen (nitrate) and 9% in phosphorus (TP). We found out the water quality could meet the BOD target by the 50% peak reduction with management. All the simulations demonstrated the safety threshold method was helpful to control the loadings within the safe range of disasters and environmental quality. Moreover, from the historical data of whole island, the past deforestation policy and the mistake economic projects were the prime culprits. Consequently, this study showed a practical method to manage both the disasters and pollution in a watershed scale by the land-use management.

Combining an Analytic Hierarchy Process and TOPSIS for Selecting Postharvest Technology Method for Selayar Citrus in Indonesia

NASA Astrophysics Data System (ADS)

Dirpan, Andi

2018-05-01

This research was intended to select the best handling methods or postharvest technologies that can be used to maintain the quality of citrus fruit in Selayar, South Sulawesi, Indonesia among (1) modified atmosphere packaging (MAP (2) Controlled atmosphere storage (CAS) (3) coatings (4) hot water treatment (5) Hot Calcium Dip (HCD) by using combination between an analytic hierarchy process (AHP) and TOPSIS. Improving quality, applicability, increasing shelf life and reducing cost are used as the criteria to determine the best postharvest technologies. The results show that the most important criteria for selecting postharvest technology is improving quality followed by increasing shelf life, reducing cost and applicability. Furthermore, by using TOPSIS, it is clear that the postharvest technology that had the lowest rangking is modified atmosphere packaging (MAP), followed by controlled atmosphere storage (CAS), coatings, hot calcium dip (HCD) and hot water treatment (HWT). Therefore, it can be concluded that the best postharvest technology method for Selayar citrus is modified atmosphere packaging (MAP).

Method of controlling coherent synchroton radiation-driven degradation of beam quality during bunch length compression

DOEpatents

Douglas, David R [Newport News, VA; Tennant, Christopher D [Williamsburg, VA

2012-07-10

A method of avoiding CSR induced beam quality defects in free electron laser operation by a) controlling the rate of compression and b) using a novel means of integrating the compression with the remainder of the transport system: both are accomplished by means of dispersion modulation. A large dispersion is created in the penultimate dipole magnet of the compression region leading to rapid compression; this large dispersion is demagnified and dispersion suppression performed in a final small dipole. As a result, the bunch is short for only a small angular extent of the transport, and the resulting CSR excitation is small.

Use of artificial intelligence in the production of high quality minced meat

NASA Astrophysics Data System (ADS)

Kapovsky, B. R.; Pchelkina, V. A.; Plyasheshnik, P. I.; Dydykin, A. S.; Lazarev, A. A.

2017-09-01

A design for an automatic line for minced meat production according to new production technology based on an innovative meat milling method is proposed. This method allows the necessary degree of raw material comminution at the stage of raw material preparation to be obtained, which leads to production intensification due to the traditional meat mass comminution equipment being unnecessary. To ensure consistent quality of the product obtained, the use of on-line automatic control of the technological process for minced meat production is envisaged. This system has been developed using artificial intelligence methods and technologies. The system is trainable during the operation process, adapts to changes in processed raw material characteristics and to external impacts that affect the system operation, and manufactures meat shavings with minimal dispersion of the typical particle size. The control system includes equipment for express analysis of the chemical composition of the minced meat and its temperature after comminution. In this case, the minced meat production process can be controlled strictly as a function of time, which excludes subjective factors for assessing the degree of finished product readiness. This will allow finished meat products with consistent, targeted high quality to be produced.

Intergenerational volunteering and quality of life: mixed methods evaluation of a randomized control trial involving persons with mild to moderate dementia.

PubMed

George, Daniel R

2011-09-01

This article reports on a mixed methods evaluation of a randomized control trial in Cleveland, Ohio, USA, that assessed whether an intergenerational volunteering intervention could enhance quality of life (QOL) for persons with mild to moderate dementia. Fifteen participants were randomized into intervention and control groups. The intervention group participated in hour-long volunteer sessions with a kindergarten class and an older elementary class in alternating weeks over a 5-month interval. Psychometric data on cognitive functioning, stress, depression, sense of purpose, and sense of usefulness were collected at baseline and at the close of the intervention, and change scores were computed and analyzed for all variables. Ethnography was carried out through the duration of the study, and narrative interviews were held with participants and caregivers. A modified grounded theory approach was used for qualitative analysis. Quantitative analysis demonstrated a significant decrease in stress for the intervention group. Qualitative analysis identified three main pathways through which intergenerational volunteering affected QOL: perceived health benefits, sense of purpose and sense of usefulness, and relationships. Mixed methods evaluation demonstrated that intergenerational volunteering might enhance quality of life through several key pathways, most significantly reduced stress.

From quality markers to data mining and intelligence assessment: A smart quality-evaluation strategy for traditional Chinese medicine based on quality markers.

PubMed

Bai, Gang; Zhang, Tiejun; Hou, Yuanyuan; Ding, Guoyu; Jiang, Min; Luo, Guoan

2018-05-15

The quality of traditional Chinese medicine (TCM) forms the foundation of its clinical efficacy. The standardization of TCM is the most important task of TCM modernization. In recent years, there has been great progress in the quality control of TCM. However, there are still many issues related to the current quality standards, and it is difficult to objectively evaluate and effectively control the quality of TCM. To face these challenge, we summarized the current quality marker (Q-marker) research based on its characteristics and benefits, and proposed a reasonable and intelligentized quality evaluation strategy for the development and application of Q-markers. Ultra-performance liquid chromatography-quadrupole/time-of-flight with partial least squares-discriminant analysis was suggested to screen the chemical markers from Chinese medicinal materials (CMM), and a bioactive-guided evaluation method was used to select the Q-markers. Near-infrared spectroscopy (NIRS), based on the distinctive wavenumber zones or points from the Q-markers, was developed for its determination. Then, artificial intelligence algorithms were used to clarify the complex relationship between the Q-markers and their integral functions. Internet and mobile communication technology helped us to perform remote analysis and determine the information feedback of test samples. The quality control research, evaluation, standard establishment and quality control of TCM must be based on the systematic analysis of Q-markers to study and describe the material basis of TCM efficacy, define the chemical markers in the plant body, and understand the process of herb drug acquisition, change and transmission laws affecting metabolism and exposure. Based on the advantages of chemometrics, new sensor technologies, including infrared spectroscopy, hyperspectral imaging, chemical imaging, electronic nose and electronic tongue, have become increasingly important in the quality evaluation of CMM. Inspired by the concept of Q-marker, the quantitation can be achieved with the help of artificial intelligence, and these subtle differences can be discovered, allowing the quantitative analysis by NIRS and providing a quick and easy detection method for CMM quality evaluations. The concept of Q-markers focused on unique CMM differences, dynamic changes and their transmission and traceability to establish an overall quality control and traceability system. Based on the basic attributes, an integration model and artificial intelligence research path was proposed, with the hope of providing new ideas and perspectives for the TCM quality management. Copyright © 2018 Elsevier GmbH. All rights reserved.

Economic evaluations of tobacco control mass media campaigns: a systematic review

PubMed Central

Atusingwize, Edwinah; Lewis, Sarah; Langley, Tessa

2015-01-01

Background International evidence shows that mass media campaigns are effective tobacco control interventions. However, they require substantial investment; a key question is whether their costs are justified by their benefits. The aim of this study was to systematically and comprehensively review economic evaluations of tobacco control mass media campaigns. Methods An electronic search of databases and grey literature was conducted to identify all published economic evaluations of tobacco control mass media campaigns. The authors reviewed studies independently and assessed the quality of studies using the Drummond 10-point checklist. A narrative synthesis was used to summarise the key features and quality of the identified studies. Results 10 studies met the inclusion criteria and were included in the review. All the studies included a cost effectiveness analysis, a cost utility analysis or both. The methods were highly heterogeneous, particularly in terms of the types of costs included. On the whole, studies were well conducted, but the interventions were often poorly described in terms of campaign content and intensity, and cost information was frequently inadequate. All studies concluded that tobacco control mass media campaigns are a cost effective public health intervention. Conclusions The evidence on the cost effectiveness of tobacco control mass media campaigns is limited, but of acceptable quality and consistently suggests that they offer good value for money. PMID:24985730

Computer applications in scientific balloon quality control

NASA Astrophysics Data System (ADS)

Seely, Loren G.; Smith, Michael S.

Seal defects and seal tensile strength are primary determinants of product quality in scientific balloon manufacturing; they therefore require a unit of quality measure. The availability of inexpensive and powerful data-processing tools can serve as the basis of a quality-trends-discerning analysis of products. The results of one such analysis are presently given in graphic form for use on the production floor. Software descriptions and their sample outputs are presented, together with a summary of overall and long-term effects of these methods on product quality.

Self-assessment procedure using fuzzy sets

NASA Astrophysics Data System (ADS)

Mimi, Fotini

2000-10-01

Self-Assessment processes, initiated by a company itself and carried out by its own people, are considered to be the starting point for a regular strategic or operative planning process to ensure a continuous quality improvement. Their importance has increased by the growing relevance and acceptance of international quality awards such as the Malcolm Baldrige National Quality Award, the European Quality Award and the Deming Prize. Especially award winners use the instrument of a systematic and regular Self-Assessment and not only because they have to verify their quality and business results for at least three years. The Total Quality Model of the European Foundation for Quality Management (EFQM), used for the European Quality Award, is the basis for Self-Assessment in Europe. This paper presents a self-assessment supporting method based on a methodology of fuzzy control systems providing an effective means of converting the linguistic approximation into an automatic control strategy. In particular, the elements of the Quality Model mentioned above are interpreted as linguistic variables. The LR-type of a fuzzy interval is used for their representation. The input data has a qualitative character based on empirical investigation and expert knowledge and therefore the base- variables are ordinal scaled. The aggregation process takes place on the basis of a hierarchical structure. Finally, in order to render the use of the method more practical a software system on PC basis is developed and implemented.

Development of quality control and instrumentation performance metrics for diffuse optical spectroscopic imaging instruments in the multi-center clinical environment

NASA Astrophysics Data System (ADS)

Keene, Samuel T.; Cerussi, Albert E.; Warren, Robert V.; Hill, Brian; Roblyer, Darren; Leproux, AnaÑ--s.; Durkin, Amanda F.; O'Sullivan, Thomas D.; Haghany, Hosain; Mantulin, William W.; Tromberg, Bruce J.

2013-03-01

Instrument equivalence and quality control are critical elements of multi-center clinical trials. We currently have five identical Diffuse Optical Spectroscopic Imaging (DOSI) instruments enrolled in the American College of Radiology Imaging Network (ACRIN, #6691) trial located at five academic clinical research sites in the US. The goal of the study is to predict the response of breast tumors to neoadjuvant chemotherapy in 60 patients. In order to reliably compare DOSI measurements across different instruments, operators and sites, we must be confident that the data quality is comparable. We require objective and reliable methods for identifying, correcting, and rejecting low quality data. To achieve this goal, we developed and tested an automated quality control algorithm that rejects data points below the instrument noise floor, improves tissue optical property recovery, and outputs a detailed data quality report. Using a new protocol for obtaining dark-noise data, we applied the algorithm to ACRIN patient data and successfully improved the quality of recovered physiological data in some cases.

Pterodon pubescens oil: characterisation, certification of origin and quality control via mass spectrometry fingerprinting analysis.

PubMed

Cabral, E C; Sevart, L; Spindola, H M; Coelho, M B; Sousa, I M O; Queiroz, N C A; Foglio, M A; Eberlin, M N; Riveros, J M

2013-02-01

The oil obtained from Pterodon pubescens (Leguminosae) seeds are known to display anti-cancer, anti-dermatogenic and anti-nociceptive activitiy. Phytochemical studies have demonstrated that its main constituents are diterpenoids with voucapan skeletons. Considering the potential biological activities of the oil, rapid and efficient methods for assessing its quality would facilitate certification and quality control. To develop a direct mass spectrometric fingerprinting method for the P. pubescens seed oil that would focus on the major diterpenoids constituents, enabling quality control, origin certification and recognition of marker species in commercially available products. Two techniques were used: (i) direct infusion electrospray ionisation (ESI) mass spectrometry after solvent extraction and dilution and (ii) ambient desorption/ionisation via easy ambient sonic-spray ionisation, EASI(+)-MS, performed directly on the seed surface or at a paper surface imprinted with the oil. From a combination of ESI-MS, HRESI-MS and ESI-MS/MS data, 12 diterpenes were characterised, and typical profiles were obtained for the oil extract or the crude oil via both ESI-MS and EASI-MS. These techniques require no or very simple sample preparation protocols and the whole analytical processes with spectra acquisition take just a few minutes. Both techniques, but particularly EASI-MS, provide simple, fast and efficient MS fingerprinting methodologies to characterise the P. pubescens oil with typical (di)terpene profiles being applicable to quality control and certification of authenticity and origin. Copyright © 2012 John Wiley & Sons, Ltd.

Validation of a method for the determination of zolpidem in human plasma using LC with fluorescence detection.

PubMed

Ring, P R; Bostick, J M

2000-04-01

A sensitive and selective high-performance liquid chromatography (HPLC) method was developed for the determination of zolpidem in human plasma. Zolpidem and the internal standard (trazodone) were extracted from human plasma that had been made basic. The basic sample was loaded onto a conditioned Bond Elut C18 cartridge, rinsed with water and eluted with methanol. Forty microliters were then injected onto the LC system. Separation was achieved on a C18 column (150 x 4.6 mm, 5 microm) with a mobile phase composed of acetonitrile:50 mM potassium phosphate monobasic at pH 6.0 (4:6, v/v). Detection was by fluorescence, with excitation at 254 nm and emission at 400 nm. The retention times of zolpidem and internal standard were approximately 4.7 and 5.3 min, respectively. The LC run time was 8 min. The assay was linear in concentration range 1-400 ng/ml for zolpidem in human plasma. The analysis of quality control samples for zolpidem (3, 30, and 300 ng/ml) demonstrated excellent precision with relative standard deviations (RSD) of 3.7, 4.6, and 3.0%, respectively (n = 18). The method was accurate with all intraday (n = 6) and overall (n = 18) mean concentrations within 5.8% from nominal at all quality control sample concentrations. This method was also performed using a Gilson Aspec XL automated sample processor and autoinjector. The samples were manually fortified with internal standard and made basic. The aspec then performed the solid phase extraction and made injections of the samples onto the LC system. Using the automated procedure for analysis, quality control samples for zolpidem (3, 30, and 300 ng/ml) demonstrated acceptable precision with RSD values of 9.0, 4.9, and 5.1%, respectively (n = 12). The method was accurate with all intracurve (n = 4) and overall (n = 12) mean values being less than 10.8% from nominal at all quality control sample concentrations.

A novel frame-level constant-distortion bit allocation for smooth H.264/AVC video quality

NASA Astrophysics Data System (ADS)

Liu, Li; Zhuang, Xinhua

2009-01-01

It is known that quality fluctuation has a major negative effect on visual perception. In previous work, we introduced a constant-distortion bit allocation method [1] for H.263+ encoder. However, the method in [1] can not be adapted to the newest H.264/AVC encoder directly as the well-known chicken-egg dilemma resulted from the rate-distortion optimization (RDO) decision process. To solve this problem, we propose a new two stage constant-distortion bit allocation (CDBA) algorithm with enhanced rate control for H.264/AVC encoder. In stage-1, the algorithm performs RD optimization process with a constant quantization QP. Based on prediction residual signals from stage-1 and target distortion for smooth video quality purpose, the frame-level bit target is allocated by using a close-form approximations of ratedistortion relationship similar to [1], and a fast stage-2 encoding process is performed with enhanced basic unit rate control. Experimental results show that, compared with original rate control algorithm provided by H.264/AVC reference software JM12.1, the proposed constant-distortion frame-level bit allocation scheme reduces quality fluctuation and delivers much smoother PSNR on all testing sequences.

[Establishment of biological assess for quality control of Fuzi based on determination of premature ventricular contractions in rats].

PubMed

Zhao, Zhi-Hao; Zhang, Ding-Kun; Wu, Ming-Quan; Li, Chun-Yu; Cao, Li-Juan; Zhang, Ping; Liu, Cui-Zhe; Wang, Jia-Bo; Xiao, Xiao-He

2016-10-01

Aconiti Lateralis Radix (Fuzi) is a toxic traditional Chinese medicine with definite efficacy. In order to improve the quality control of its different prepared products and ensure the security in clinic, it is significant to establish a method of quality evaluation related to clinic adverse effects. Aiming at the important biological marker of early cardiac toxicity reaction, there was no method to detect it. In this manuscript, a novel approach for measuring the minimal toxic dose (MTD) of premature ventricular contractions (PVC) poisoning of rats was established. Then, the determination methodology and conditions were optimized to meet the needs of the quality and biological assessment, including animal sex, weight, stability of standards and test solutions. Using this method, the MTD value of different Fuzi products were determined, such as Heishunpian, Baifupian, Zhengfupian, Baofupian, and Paotianxiong. The results showed that the MTD of Fuzi was significantly decreased after detoxification processed (P<0.05) and the MTD of Heishunpian, Zhengfupian, Baofupian and Baifupian was as much as 15.76, 22.36, 19.65 and 20.97 times to that of unprocessed Shengfuzi. In addition, Paotianxiong could not induce PVC in rats, which indicated that Paotianxiong was nontoxic and safe.This method could appropriately reflects the cardiotoxity of Fuzi and its prepared samples. Together with the chemical composition analysis, the contents of diester alkaloids were explored including aconitine, mesaconitine and hypaconitine as well as monoester alkaloids in Fuzi and its prepared products were significantly associated with PVC. Furthermore, there may be some components undetermined facilitating arrhythmia to be worth exploring. This research provides an overall and comprehensive approach to diagnose early clinical cardiotoxity and control the quality of Fuzi, which could not only be a complementary solution for the chemical evaluation, but a new method to ensure its efficacy and security of clinical application. Copyright© by the Chinese Pharmaceutical Association.

What can we learn from a decade of database audits? The Duke Clinical Research Institute experience, 1997--2006.

PubMed

Rostami, Reza; Nahm, Meredith; Pieper, Carl F

2009-04-01

Despite a pressing and well-documented need for better sharing of information on clinical trials data quality assurance methods, many research organizations remain reluctant to publish descriptions of and results from their internal auditing and quality assessment methods. We present findings from a review of a decade of internal data quality audits performed at the Duke Clinical Research Institute, a large academic research organization that conducts data management for a diverse array of clinical studies, both academic and industry-sponsored. In so doing, we hope to stimulate discussions that could benefit the wider clinical research enterprise by providing insight into methods of optimizing data collection and cleaning, ultimately helping patients and furthering essential research. We present our audit methodologies, including sampling methods, audit logistics, sample sizes, counting rules used for error rate calculations, and characteristics of audited trials. We also present database error rates as computed according to two analytical methods, which we address in detail, and discuss the advantages and drawbacks of two auditing methods used during this 10-year period. Our review of the DCRI audit program indicates that higher data quality may be achieved from a series of small audits throughout the trial rather than through a single large database audit at database lock. We found that error rates trended upward from year to year in the period characterized by traditional audits performed at database lock (1997-2000), but consistently trended downward after periodic statistical process control type audits were instituted (2001-2006). These increases in data quality were also associated with cost savings in auditing, estimated at 1000 h per year, or the efforts of one-half of a full time equivalent (FTE). Our findings are drawn from retrospective analyses and are not the result of controlled experiments, and may therefore be subject to unanticipated confounding. In addition, the scope and type of audits we examine here are specific to our institution, and our results may not be broadly generalizable. Use of statistical process control methodologies may afford advantages over more traditional auditing methods, and further research will be necessary to confirm the reliability and usability of such techniques. We believe that open and candid discussion of data quality assurance issues among academic and clinical research organizations will ultimately benefit the entire research community in the coming era of increased data sharing and re-use.

Managing quality of teaching and learning in the ophthalmic nursing course.

PubMed

Law, M L

2000-02-01

With auditing of teaching and learning in earnest by the Quality Assurance Agency for the Higher Education Funding Council, the nature of quality in education is top on the agenda for educational stakeholders. However, the nature of quality is difficult to define and measure. This is because quality is essentially a subjective perception and can mean different things to different individuals. Therefore, attempt to quantify and measure quality is difficult and problematic but is necessary for personal, professional, bureaucratic, political and stakeholder demands for accountability, and demonstration of efficiency, effectiveness and value for money. Using a total quality management framework, the internal controls of quality in the ophthalmic nursing course and at the faculty level are considered. The wider contexts of quality control from the institutional, political and at the customer's levels are explored. This paper concludes that the various methods used to control and measure quality may provide useful information for service clarity and a basis for service development. However, such information needs to be treated with caution and interpreted in the context and environment in which this information is generated. Ultimately, the issues of quality in teaching and learning may be addressed by the teacher's commitment to be developed as a reflective practitioner.

Standard Free Droplet Digital Polymerase Chain Reaction as a New Tool for the Quality Control of High-Capacity Adenoviral Vectors in Small-Scale Preparations

PubMed Central

Boehme, Philip; Stellberger, Thorsten; Solanki, Manish; Zhang, Wenli; Schulz, Eric; Bergmann, Thorsten; Liu, Jing; Doerner, Johannes; Baiker, Armin E.

2015-01-01

Abstract High-capacity adenoviral vectors (HCAdVs) are promising tools for gene therapy as well as for genetic engineering. However, one limitation of the HCAdV vector system is the complex, time-consuming, and labor-intensive production process and the following quality control procedure. Since HCAdVs are deleted for all viral coding sequences, a helper virus (HV) is needed in the production process to provide the sequences for all viral proteins in trans. For the purification procedure of HCAdV, cesium chloride density gradient centrifugation is usually performed followed by buffer exchange using dialysis or comparable methods. However, performing these steps is technically difficult, potentially error-prone, and not scalable. Here, we establish a new protocol for small-scale production of HCAdV based on commercially available adenovirus purification systems and a standard method for the quality control of final HCAdV preparations. For titration of final vector preparations, we established a droplet digital polymerase chain reaction (ddPCR) that uses a standard free-end-point PCR in small droplets of defined volume. By using different probes, this method is capable of detecting and quantifying HCAdV and HV in one reaction independent of reference material, rendering this method attractive for accurately comparing viral titers between different laboratories. In summary, we demonstrate that it is possible to produce HCAdV in a small scale of sufficient quality and quantity to perform experiments in cell culture, and we established a reliable protocol for vector titration based on ddPCR. Our method significantly reduces time and required equipment to perform HCAdV production. In the future the ddPCR technology could be advantageous for titration of other viral vectors commonly used in gene therapy. PMID:25640117

A quality control method for intensity-modulated radiation therapy planning based on generalized equivalent uniform dose.

PubMed

Pang, Haowen; Sun, Xiaoyang; Yang, Bo; Wu, Jingbo

2018-05-01

To ensure good quality intensity-modulated radiation therapy (IMRT) planning, we proposed the use of a quality control method based on generalized equivalent uniform dose (gEUD) that predicts absorbed radiation doses in organs at risk (OAR). We conducted a retrospective analysis of patients who underwent IMRT for the treatment of cervical carcinoma, nasopharyngeal carcinoma (NPC), or non-small cell lung cancer (NSCLC). IMRT plans were randomly divided into data acquisition and data verification groups. OAR in the data acquisition group for cervical carcinoma and NPC were further classified as sub-organs at risk (sOAR). The normalized volume of sOAR and normalized gEUD (a = 1) were analyzed using multiple linear regression to establish a fitting formula. For NSCLC, the normalized intersection volume of the planning target volume (PTV) and lung, the maximum diameter of the PTV (left-right, anterior-posterior, and superior-inferior), and the normalized gEUD (a = 1) were analyzed using multiple linear regression to establish a fitting formula for the lung gEUD (a = 1). The r-squared and P values indicated that the fitting formula was a good fit. In the data verification group, IMRT plans verified the accuracy of the fitting formula, and compared the gEUD (a = 1) for each OAR between the subjective method and the gEUD-based method. In conclusion, the gEUD-based method can be used effectively for quality control and can reduce the influence of subjective factors on IMRT planning optimization. © 2018 The Authors. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on behalf of American Association of Physicists in Medicine.

Method and system for automated on-chip material and structural certification of MEMS devices

DOEpatents

Sinclair, Michael B.; DeBoer, Maarten P.; Smith, Norman F.; Jensen, Brian D.; Miller, Samuel L.

2003-05-20

A new approach toward MEMS quality control and materials characterization is provided by a combined test structure measurement and mechanical response modeling approach. Simple test structures are cofabricated with the MEMS devices being produced. These test structures are designed to isolate certain types of physical response, so that measurement of their behavior under applied stress can be easily interpreted as quality control and material properties information.

On-Line Point Positioning with Single Frame Camera Data

DTIC Science & Technology

1992-03-15

tion algorithms and methods will be found in robotics and industrial quality control. 1. Project data The project has been defined as "On-line point...development and use of the OLT algorithms and meth- ods for applications in robotics , industrial quality control and autonomous vehicle naviga- tion...Of particular interest in robotics and autonomous vehicle navigation is, for example, the task of determining the position and orientation of a mobile

Data quality assurance and control in cognitive research: Lessons learned from the PREDICT-HD study.

PubMed

Westervelt, Holly James; Bernier, Rachel A; Faust, Melanie; Gover, Mary; Bockholt, H Jeremy; Zschiegner, Roland; Long, Jeffrey D; Paulsen, Jane S

2017-09-01

We discuss the strategies employed in data quality control and quality assurance for the cognitive core of Neurobiological Predictors of Huntington's Disease (PREDICT-HD), a long-term observational study of over 1,000 participants with prodromal Huntington disease. In particular, we provide details regarding the training and continual evaluation of cognitive examiners, methods for error corrections, and strategies to minimize errors in the data. We present five important lessons learned to help other researchers avoid certain assumptions that could potentially lead to inaccuracies in their cognitive data. Copyright © 2017 John Wiley & Sons, Ltd.

Construction of Genetically Engineered Streptococcus gordonii Strains to Provide Control in QPCR Assays for Assessing Microbiological Quality in Recreational Water.

EPA Science Inventory

Quantitative PCR (QPCR) methods for beach monitoring by estimating abundance of Enterococcus spp. in recreational waters use internal, positive controls which address only the amplification of target DNA. In this study two internal, positive controls were developed to control for...

Quality Space and Launch Requirements, Addendum to AS9100C

DTIC Science & Technology

2015-05-08

45 8.9.1 Statistical Process Control (SPC) .......................................................................... 45...SMC Space and Missile Systems Center SME Subject Matter Expert SOW Statement of Work SPC Statistical Process Control SPO System Program Office SRP...occur without any individual data exceeding the control limits. Control limits are developed using standard statistical methods or other approved

Category 1 external quality assessment program for serum creatinine.

PubMed

González-Lao, Elisabet; Díaz-Garzón, Jorge; Corte, Zoraida; Ricós, Carmen; Perich, Carmen; Álvarez, Virtudes; Simón, Margarita; Minchinela, Joana; García-Lario, José Vicente; Boned, Beatriz; Biosca, Carmen; Cava, Fernando; Fernández-Fernández, Pilar; Fernández-Calle, Pilar

2017-03-01

The Commission of Analytical Quality and the Committee of External Quality Programs of Spanish Society of Laboratory Medicine (SEQC) in collaboration with the Dutch Foundation for the Quality organized the first national category 1 External Quality Assessment Programs (EQAP) pilot study. The aim is to evaluate the standardization of serum creatinine measurements in the Spanish laboratories through a category 1 external quality assurance program with commutable material and reference method assigned values. A total of 87 Spanish laboratories were involved in this program in 2015. Each day a sample control was measured by duplicate during 6 consecutive days. Percentage deviations and coefficients of variation obtained were compared with quality specifications derived from biological variation. A total of 1044 creatinine results were obtained. Laboratories were coded in 11 different method-traceability combinations. Only enzymatic methods get all results within the acceptability limits. To participate in a category 1 EQAP is a valuable tool to assess the standardization degree in our country; a big effort should be made to promote laboratories to change their procedures and to use enzymatic creatinine methods, in order to achieve a satisfactory standardization degree for this important analyte.

Chemometrics-based process analytical technology (PAT) tools: applications and adaptation in pharmaceutical and biopharmaceutical industries.

PubMed

Challa, Shruthi; Potumarthi, Ravichandra

2013-01-01

Process analytical technology (PAT) is used to monitor and control critical process parameters in raw materials and in-process products to maintain the critical quality attributes and build quality into the product. Process analytical technology can be successfully implemented in pharmaceutical and biopharmaceutical industries not only to impart quality into the products but also to prevent out-of-specifications and improve the productivity. PAT implementation eliminates the drawbacks of traditional methods which involves excessive sampling and facilitates rapid testing through direct sampling without any destruction of sample. However, to successfully adapt PAT tools into pharmaceutical and biopharmaceutical environment, thorough understanding of the process is needed along with mathematical and statistical tools to analyze large multidimensional spectral data generated by PAT tools. Chemometrics is a chemical discipline which incorporates both statistical and mathematical methods to obtain and analyze relevant information from PAT spectral tools. Applications of commonly used PAT tools in combination with appropriate chemometric method along with their advantages and working principle are discussed. Finally, systematic application of PAT tools in biopharmaceutical environment to control critical process parameters for achieving product quality is diagrammatically represented.

WLN's Database: New Directions.

ERIC Educational Resources Information Center

Ziegman, Bruce N.

1988-01-01

Describes features of the Western Library Network's database, including the database structure, authority control, contents, quality control, and distribution methods. The discussion covers changes in distribution necessitated by increasing telecommunications costs and the development of optical data disk products. (CLB)

Simultaneous quantification and splenocyte-proliferating activities of nucleosides and bases in Cervi cornu Pantotrichum

PubMed Central

Zong, Ying; Wang, Yu; Li, Hang; Li, Na; Zhang, Hui; Sun, Jiaming; Niu, Xiaohui; Gao, Xiaochen

2014-01-01

Background: Cervi Cornu Pantotrichum has been a well known traditional Chinese medicine, which is young horn of Cervus Nippon Temminck (Hualurong: HLR). At present, the methods used for the quality control of Cervi Cornu Pantotrichum show low specificity. Objective: To describe a holistic method based on chemical characteristics and splenocyte-proliferating activities to evaluate the quality of HLR. Materials and Methods: The nucleosides and bases from HLR were identified by high performance liquid chromatography electrospray ionization mass spectrometry (HPLC-ESI-MS), and six of them were chosen to be used for simultaneous HPLC quantification according to the results of proliferation of mouse splenocytes in vitro. Results: In this study, eight nucleosides and bases have been identified. In addition, uracil, hypoxanthine, uridine, inosine, guanosine, and adenosine were chosen to be used for simultaneous HPLC quantification. Simultaneous quantification of these six substances was performed on ten groups of HLR under the condition of a TIANHE Kromasil C18 column (5 μm, 4.6 mm × 250 mm i.d.) and a gradient elution of water and acetonitrile. Of the ten groups, HLR displayed the highest total nucleoside contents (TNC, sum of adenosine and uracil, 0.412 mg/g) with the strongest splenocyte-proliferating activities. Conclusion: These results suggest that TNC (such as particularly highly contained adenosine and uracil) in HLR has a certain correlation with the activity of splenocyte-proliferating, and it may be used as a quality control for HLR. This comprehensive method could be applied to other traditional Chinese medicines to ameliorate their quality control. PMID:25422536

Image quality in thoracic 4D cone-beam CT: A sensitivity analysis of respiratory signal, binning method, reconstruction algorithm, and projection angular spacing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shieh, Chun-Chien; Kipritidis, John; O’Brien, Ricky T.

Purpose: Respiratory signal, binning method, and reconstruction algorithm are three major controllable factors affecting image quality in thoracic 4D cone-beam CT (4D-CBCT), which is widely used in image guided radiotherapy (IGRT). Previous studies have investigated each of these factors individually, but no integrated sensitivity analysis has been performed. In addition, projection angular spacing is also a key factor in reconstruction, but how it affects image quality is not obvious. An investigation of the impacts of these four factors on image quality can help determine the most effective strategy in improving 4D-CBCT for IGRT. Methods: Fourteen 4D-CBCT patient projection datasets withmore » various respiratory motion features were reconstructed with the following controllable factors: (i) respiratory signal (real-time position management, projection image intensity analysis, or fiducial marker tracking), (ii) binning method (phase, displacement, or equal-projection-density displacement binning), and (iii) reconstruction algorithm [Feldkamp–Davis–Kress (FDK), McKinnon–Bates (MKB), or adaptive-steepest-descent projection-onto-convex-sets (ASD-POCS)]. The image quality was quantified using signal-to-noise ratio (SNR), contrast-to-noise ratio, and edge-response width in order to assess noise/streaking and blur. The SNR values were also analyzed with respect to the maximum, mean, and root-mean-squared-error (RMSE) projection angular spacing to investigate how projection angular spacing affects image quality. Results: The choice of respiratory signals was found to have no significant impact on image quality. Displacement-based binning was found to be less prone to motion artifacts compared to phase binning in more than half of the cases, but was shown to suffer from large interbin image quality variation and large projection angular gaps. Both MKB and ASD-POCS resulted in noticeably improved image quality almost 100% of the time relative to FDK. In addition, SNR values were found to increase with decreasing RMSE values of projection angular gaps with strong correlations (r ≈ −0.7) regardless of the reconstruction algorithm used. Conclusions: Based on the authors’ results, displacement-based binning methods, better reconstruction algorithms, and the acquisition of even projection angular views are the most important factors to consider for improving thoracic 4D-CBCT image quality. In view of the practical issues with displacement-based binning and the fact that projection angular spacing is not currently directly controllable, development of better reconstruction algorithms represents the most effective strategy for improving image quality in thoracic 4D-CBCT for IGRT applications at the current stage.« less

Internal quality control: planning and implementation strategies.

PubMed

Westgard, James O

2003-11-01

The first essential in setting up internal quality control (IQC) of a test procedure in the clinical laboratory is to select the proper IQC procedure to implement, i.e. choosing the statistical criteria or control rules, and the number of control measurements, according to the quality required for the test and the observed performance of the method. Then the right IQC procedure must be properly implemented. This review focuses on strategies for planning and implementing IQC procedures in order to improve the quality of the IQC. A quantitative planning process is described that can be implemented with graphical tools such as power function or critical-error graphs and charts of operating specifications. Finally, a total QC strategy is formulated to minimize cost and maximize quality. A general strategy for IQC implementation is recommended that employs a three-stage design in which the first stage provides high error detection, the second stage low false rejection and the third stage prescribes the length of the analytical run, making use of an algorithm involving the average of normal patients' data.

Trace Contaminant Control During the International Space Station's On-Orbit Assembly and Outfitting

NASA Technical Reports Server (NTRS)

Perry, J. L.

2017-01-01

Achieving acceptable cabin air quality must balance competing elements during spacecraft design, assembly, ground processing, and flight operations. Among the elements that contribute to the trace chemical contaminant load and, therefore, the cabin air quality aboard crewed spacecraft are the vehicle configuration, crew size and activities, mission duration and objectives, materials selection, and vehicle manufacturing and preflight ground processing methods. Trace chemical contaminants produced from pervasive sources such as equipment offgassing, human metabolism, and cleaning fluids during preflight ground processing present challenges to maintaining acceptable cabin air quality. To address these challenges, both passive and active contamination control techniques are used during a spacecraft's design, manufacturing, preflight preparation, and operational phases. Passive contamination control methods seek to minimize the equipment offgassing load by selecting materials, manufacturing processes, preflight preparation processes, and in-flight operations that have low chemical offgassing characteristics. Passive methods can be employed across the spacecraft's entire life cycle from conceptual design through flight operations. However, because the passive contamination control techniques cannot fully eliminate the contaminant load, active contamination control equipment must be deployed aboard the spacecraft to purify and revitalize the cabin atmosphere during in-flight operations. Verifying that the passive contamination control techniques have successfully maintained the total trace contaminant load within the active contamination control equipment's capabilities occurs late in the preflight preparation stages. This verification consists of subjecting the spacecraft to an offgassing test to determine the trace contaminant load. This load is then assessed versus the active contamination control equipment's capabilities via trace contaminant control (TCC) engineering analysis. During the International Space Station's (ISS's) on-orbit assembly and outfitting, a series of engineering analyses were conducted to evaluate how effective the passive TCC methods were relative to providing adequate operational margin for the active TCC equipment's capabilities aboard the ISS. These analyses were based on habitable module and cargo vehicle offgassing test results. The offgassing test for a fully assembled module or cargo vehicle is an important preflight spacecraft evaluation method that has been used successfully during all crewed spacecraft programs to provide insight into how effectively the passive contamination control methods limit the equipment offgassing component of the overall trace contaminant generation load. The progression of TCC assessments beginning in 1998 with the ISS's first habitable element launch and continuing through the final pressurized element's arrival in 2010 are presented. Early cargo vehicle flight assessments between 2008 and 2011 are also presented as well as a discussion on predictive methods for assessing cargo via a purely analytical technique. The technical approach for TCC employed during this 13-year period successfully maintained the cabin atmospheric quality within specified parameters during the technically challenging ISS assembly and outfitting stages. The following narrative provides details on the important role of spacecraft offgassing testing, trace contaminant performance requirements, and flight rules for achieving the ultimate result-a cabin environment that enables people to live and work safely in space.

Parametric Optimization Of Gas Metal Arc Welding Process By Using Grey Based Taguchi Method On Aisi 409 Ferritic Stainless Steel

NASA Astrophysics Data System (ADS)

Ghosh, Nabendu; Kumar, Pradip; Nandi, Goutam

2016-10-01

Welding input process parameters play a very significant role in determining the quality of the welded joint. Only by properly controlling every element of the process can product quality be controlled. For better quality of MIG welding of Ferritic stainless steel AISI 409, precise control of process parameters, parametric optimization of the process parameters, prediction and control of the desired responses (quality indices) etc., continued and elaborate experiments, analysis and modeling are needed. A data of knowledge - base may thus be generated which may be utilized by the practicing engineers and technicians to produce good quality weld more precisely, reliably and predictively. In the present work, X-ray radiographic test has been conducted in order to detect surface and sub-surface defects of weld specimens made of Ferritic stainless steel. The quality of the weld has been evaluated in terms of yield strength, ultimate tensile strength and percentage of elongation of the welded specimens. The observed data have been interpreted, discussed and analyzed by considering ultimate tensile strength ,yield strength and percentage elongation combined with use of Grey-Taguchi methodology.

Piloted simulation study of two tilt-wing control concepts

NASA Technical Reports Server (NTRS)

Birckelbaw, Lourdes G.; Corliss, Lloyd D.

1994-01-01

A two-phase piloted simulation study was conducted to investigate alternative wing and flap controls for tilt-wing aircraft. The initial phase of the study compared the flying qualities of both a conventional (programmed) flap and an innovative geared flap. The second phase of the study introduced an alternate method of pilot control for the geared flap and further studied the flying qualities of the programmed flap, and two geared flap configurations. In general, the pilot rating showed little variation between the programmed flap and the geared flap control concepts. Some differences between the two concepts were noticed and are discussed in this paper. The addition of pitch attitude stabilization in the second phase of the study greatly enhanced the aircraft flying qualities. This paper describes the simulated tilt-wing aircraft and the flap control concepts and presents the results of both phases of the simulation study.

Does walking improve disability status, function, or quality of life in adults with chronic low back pain? A systematic review.

PubMed

Lawford, Belinda J; Walters, Julie; Ferrar, Katia

2016-06-01

To establish the effectiveness of walking alone and walking compared to other non-pharmacological management methods to improve disability, quality of life, or function in adults with chronic low back pain. A systematic search of the following databases was undertaken: Medline, Embase, CINAHL, Scopus, Pedro, SportDiscus, Cochrane Central Register of Controlled Trials. The following keywords were used: 'back pain' or 'low back pain' or 'chronic low back pain' and 'walk*' or 'ambulation' or 'treadmill*' or 'pedometer*' or 'acceleromet*' or 'recreational' and 'disability' or 'quality of life' or 'function*'. Primary research studies with an intervention focus that investigated walking as the primary intervention compared to no intervention or any other non-pharmacological method in adults with chronic low back pain (duration >3 months). Seven randomised controlled trials involving 869 participants were included in the review. There was no evidence that walking was more effective than other management methods such as usual care, specific strength exercises, medical exercise therapy, or supervised exercise classes. One study found over-ground walking to be superior to treadmill walking, and another found internet-mediated walking to be more beneficial than non-internet-mediated walking in the short term. There is low quality evidence to suggest that walking is as effective as other non-pharmacological management methods at improving disability, function, and quality of life in adults with chronic low back pain. © The Author(s) 2015.

30 CFR 550.302 - Definitions concerning air quality.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pollutant means any combination of agents for which the Environmental Protection Agency (EPA) has... is calculated by air quality modeling (or other methods determined by the Administrator of EPA to be... available control technology (BACT) means an emission limitation based on the maximum degree of reduction...

30 CFR 250.302 - Definitions concerning air quality.

Code of Federal Regulations, 2010 CFR

2010-07-01

... any combination of agents for which the Environmental Protection Agency (EPA) has established... by air quality modeling (or other methods determined by the Administrator of EPA to be reliable) not... control technology (BACT) means an emission limitation based on the maximum degree of reduction for each...

30 CFR 550.302 - Definitions concerning air quality.

Code of Federal Regulations, 2012 CFR

2012-07-01

... pollutant means any combination of agents for which the Environmental Protection Agency (EPA) has... is calculated by air quality modeling (or other methods determined by the Administrator of EPA to be... available control technology (BACT) means an emission limitation based on the maximum degree of reduction...

30 CFR 550.302 - Definitions concerning air quality.

Code of Federal Regulations, 2014 CFR

2014-07-01

... pollutant means any combination of agents for which the Environmental Protection Agency (EPA) has... is calculated by air quality modeling (or other methods determined by the Administrator of EPA to be... available control technology (BACT) means an emission limitation based on the maximum degree of reduction...

Organizational Culture in Community Colleges: Connecting Market Orientation, Quality, and Student Engagement

ERIC Educational Resources Information Center

McManimon, Debra J.

2012-01-01

To enhance their competitive advantage in the marketplace, many business leaders develop market orientation strategies designed to increase customer engagement. These market orientation strategies include improvement in service delivery, relationship management, customer satisfaction, and quality control methods. There is a lack of understanding…

STATUS OF RESEARCH ON AIR QUALITY: MERCURY, TRACE ELEMENTS, AND PARTICULATE MATTER. (R827649)

EPA Science Inventory

The Air Quality Conference reviewed the state of science and policy on the pollutants mercury, trace elements, and particulate matter (PM) in the environment. Critical issues dealing with impacts on health and ecosystems, emission prevention and control, measurement methods, a...

Quality control analytical methods: refractive index.

PubMed

Allen, Loyd V

2015-01-01

There are numerous analytical methods that can be utilized in a compounding pharmacy for a quality-assurance program. Since the index of refraction of a liquid/solution is a physical constant, it can be used to assist in identification of a substance, establish its purity, and, in some instances, to determine the concentration of an analyte in solution. This article serves as an introduction to refractive index and some applications of its use in a compounding program.

Trichinella diagnostics and control: mandatory and best practices for ensuring food safety.

PubMed

Gajadhar, Alvin A; Pozio, Edoardo; Gamble, H Ray; Nöckler, Karsten; Maddox-Hyttel, Charlotte; Forbes, Lorry B; Vallée, Isabelle; Rossi, Patrizia; Marinculić, Albert; Boireau, Pascal

2009-02-23

Because of its role in human disease, there are increasing global requirements for reliable diagnostic and control methods for Trichinella in food animals to ensure meat safety and to facilitate trade. Consequently, there is a need for standardization of methods, programs, and best practices used in the control of Trichinella and trichinellosis. This review article describes the biology and epidemiology of Trichinella, and describes recommended test methods as well as modified and optimized procedures that are used in meat inspection programs. The use of ELISA for monitoring animals for infection in various porcine and equine pre- and post-slaughter programs, including farm or herd certification programs is also discussed. A brief review of the effectiveness of meat processing methods, such as freezing, cooking and preserving is provided. The importance of proper quality assurance and its application in all aspects of a Trichinella diagnostic system is emphasized. It includes the use of international quality standards, test validation and standardization, critical control points, laboratory accreditation, certification of analysts and proficiency testing. Also described, are the roles and locations of international and regional reference laboratories for trichinellosis where expert advice and support on research and diagnostics are available.

Fuzzy comprehensive evaluation of multiple environmental factors for swine building assessment and control.

PubMed

Xie, Qiuju; Ni, Ji-Qin; Su, Zhongbin

2017-10-15

In confined swine buildings, temperature, humidity, and air quality are all important for animal health and productivity. However, the current swine building environmental control is only based on temperature; and evaluation and control methods based on multiple environmental factors are needed. In this paper, fuzzy comprehensive evaluation (FCE) theory was adopted for multi-factor assessment of environmental quality in two commercial swine buildings using real measurement data. An assessment index system and membership functions were established; and predetermined weights were given using analytic hierarchy process (AHP) combined with knowledge of experts. The results show that multi-factors such as temperature, humidity, and concentrations of ammonia (NH 3 ), carbon dioxide (CO 2 ), and hydrogen sulfide (H 2 S) can be successfully integrated in FCE for swine building environment assessment. The FCE method has a high correlation coefficient of 0.737 compared with the method of single-factor evaluation (SFE). The FCE method can significantly increase the sensitivity and perform an effective and integrative assessment. It can be used as part of environmental controlling and warning systems for swine building environment management to improve swine production and welfare. Copyright © 2017 Elsevier B.V. All rights reserved.

Ion mobility spectrometry for food quality and safety.

PubMed

Vautz, W; Zimmermann, D; Hartmann, M; Baumbach, J I; Nolte, J; Jung, J

2006-11-01

Ion mobility spectrometry is known to be a fast and sensitive technique for the detection of trace substances, and it is increasingly in demand not only for protection against explosives and chemical warfare agents, but also for new applications in medical diagnosis or process control. Generally, a gas phase sample is ionized by help of ultraviolet light, ss-radiation or partial discharges. The ions move in a weak electrical field towards a detector. During their drift they collide with a drift gas flowing in the opposite direction and, therefore, are slowed down depending on their size, shape and charge. As a result, different ions reach the detector at different drift times, which are characteristic for the ions considered. The number of ions reaching the detector are a measure of the concentration of the analyte. The method enables the identification and quantification of analytes with high sensitivity (ng l(-1) range). The selectivity can even be increased - as necessary for the analyses of complex mixtures - using pre-separation techniques such as gas chromatography or multi-capillary columns. No pre-concentration of the sample is necessary. Those characteristics of the method are preserved even in air with up to a 100% relative humidity rate. The suitability of the method for application in the field of food quality and safety - including storage, process and quality control as well as the characterization of food stuffs - was investigated in recent years for a number of representative examples, which are summarized in the following, including new studies as well: (1) the detection of metabolites from bacteria for the identification and control of their growth; (2) process control in food production - beer fermentation being an example; (3) the detection of the metabolites of mould for process control during cheese production, for quality control of raw materials or for the control of storage conditions; (4) the quality control of packaging materials during the production of polymeric materials; and (5) the characterization of products - wine being an example. The challenges of such applications were operation in humid air, fast on-line analyses of complex mixtures, high sensitivity - detection limits have to be, for example, in the range of the odour limits - and, in some cases, the necessity of mobile instrumentation. It can be shown that ion mobility spectrometry is optimally capable of fulfilling those challenges for many applications.

10-year trend in quantity and quality of pediatric randomized controlled trials published in mainland China: 2002–2011

PubMed Central

2013-01-01

Background Quality assessment of pediatric randomized controlled trials (RCTs) in China is limited. The aim of this study was to evaluate the quantitative trends and quality indicators of RCTs published in mainland China over a recent 10-year period. Methods We individually searched all 17 available pediatric journals published in China from January 1, 2002 to December 30, 2011 to identify RCTs of drug treatment in participants under the age of 18 years. The quality was evaluated according to the Cochrane quality assessment protocol. Results Of 1287 journal issues containing 44398 articles, a total of 2.4% (1077/44398) articles were included in the analysis. The proportion of RCTs increased from 0.28% in 2002 to 0.32% in 2011. Individual sample sizes ranged from 10 to 905 participants (median 81 participants); 2.3% of the RCTs were multiple center trials; 63.9% evaluated Western medicine, 32.5% evaluated traditional Chinese medicine; 15% used an adequate method of random sequence generation; and 10.4% used a quasi-random method for randomization. Only 1% of the RCTs reported adequate allocation concealment and 0.6% reported the method of blinding. The follow-up period was from 7 days to 96 months, with a median of 7.5 months. There was incomplete outcome data reported in 8.3%, of which 4.5% (4/89) used intention-to-treat analysis. Only 0.4% of the included trials used adequate random sequence allocation, concealment and blinding. The articles published from 2007 to 2011 revealed an improvement in the randomization method compared with articles published from 2002 to 2006 (from 2.7% to 23.6%, p = 0.000). Conclusions In mainland China, the quantity of RCTs did not increase in the pediatric population, and the general quality was relatively poor. Quality improvements were suboptimal in the later 5 years. PMID:23914882

Moving base simulation of an integrated flight and propulsion control system for an ejector-augmentor STOVL aircraft in hover

NASA Technical Reports Server (NTRS)

Mcneill, Walter, E.; Chung, William W.; Stortz, Michael W.

1995-01-01

A piloted motion simulator evaluation, using the NASA Ames Vertical Motion Simulator, was conducted in support of a NASA Lewis Contractual study of the integration of flight and propulsion systems of a STOVL aircraft. Objectives of the study were to validate the Design Methods for Integrated Control Systems (DMICS) concept, to evaluate the handling qualities, and to assess control power usage. The E-7D ejector-augmentor STOVL fighter design served as the basis for the simulation. Handling-qualities ratings were obtained during precision hover and shipboard landing tasks. Handling-qualities ratings for these tasks ranged from satisfactory to adequate. Further improvement of the design process to fully validate the DMICS concept appears to be warranted.

Content dependent selection of image enhancement parameters for mobile displays

NASA Astrophysics Data System (ADS)

Lee, Yoon-Gyoo; Kang, Yoo-Jin; Kim, Han-Eol; Kim, Ka-Hee; Kim, Choon-Woo

2011-01-01

Mobile devices such as cellular phones and portable multimedia player with capability of playing terrestrial digital multimedia broadcasting (T-DMB) contents have been introduced into consumer market. In this paper, content dependent image quality enhancement method for sharpness and colorfulness and noise reduction is presented to improve perceived image quality on mobile displays. Human visual experiments are performed to analyze viewers' preference. Relationship between the objective measures and the optimal values of image control parameters are modeled by simple lookup tables based on the results of human visual experiments. Content dependent values of image control parameters are determined based on the calculated measures and predetermined lookup tables. Experimental results indicate that dynamic selection of image control parameters yields better image quality.

Quality assurance of the international computerised 24 h dietary recall method (EPIC-Soft).

PubMed

Crispim, Sandra P; Nicolas, Genevieve; Casagrande, Corinne; Knaze, Viktoria; Illner, Anne-Kathrin; Huybrechts, Inge; Slimani, Nadia

2014-02-01

The interview-administered 24 h dietary recall (24-HDR) EPIC-Soft® has a series of controls to guarantee the quality of dietary data across countries. These comprise all steps that are part of fieldwork preparation, data collection and data management; however, a complete characterisation of these quality controls is still lacking. The present paper describes in detail the quality controls applied in EPIC-Soft, which are, to a large extent, built on the basis of the EPIC-Soft error model and are present in three phases: (1) before, (2) during and (3) after the 24-HDR interviews. Quality controls for consistency and harmonisation are implemented before the interviews while preparing the seventy databases constituting an EPIC-Soft version (e.g. pre-defined and coded foods and recipes). During the interviews, EPIC-Soft uses a cognitive approach by helping the respondent to recall the dietary intake information in a stepwise manner and includes controls for consistency (e.g. probing questions) as well as for completeness of the collected data (e.g. system calculation for some unknown amounts). After the interviews, a series of controls can be applied by dietitians and data managers to further guarantee data quality. For example, the interview-specific 'note files' that were created to track any problems or missing information during the interviews can be checked to clarify the information initially provided. Overall, the quality controls employed in the EPIC-Soft methodology are not always perceivable, but prove to be of assistance for its overall standardisation and possibly for the accuracy of the collected data.

The utilization of six sigma and statistical process control techniques in surgical quality improvement.

PubMed

Sedlack, Jeffrey D

2010-01-01

Surgeons have been slow to incorporate industrial reliability techniques. Process control methods were applied to surgeon waiting time between cases, and to length of stay (LOS) after colon surgery. Waiting times between surgeries were evaluated by auditing the operating room records of a single hospital over a 1-month period. The medical records of 628 patients undergoing colon surgery over a 5-year period were reviewed. The average surgeon wait time between cases was 53 min, and the busiest surgeon spent 291/2 hr in 1 month waiting between surgeries. Process control charting demonstrated poor overall control of the room turnover process. Average LOS after colon resection also demonstrated very poor control. Mean LOS was 10 days. Weibull's conditional analysis revealed a conditional LOS of 9.83 days. Serious process management problems were identified in both analyses. These process issues are both expensive and adversely affect the quality of service offered by the institution. Process control mechanisms were suggested or implemented to improve these surgical processes. Industrial reliability and quality management tools can easily and effectively identify process control problems that occur on surgical services. © 2010 National Association for Healthcare Quality.

The effects of pranayama, hatha and raja yoga on physical pain and the quality of life of women with multiple sclerosis.

PubMed

Doulatabad, Shahla Najafi; Nooreyan, Khirollah; Doulatabad, Ardavan Najafi; Noubandegani, Zinat Mohebbi

2012-01-01

In a clinical trial carried out on 60 women with multiple sclerosis, the researchers obtained data using survey questionnaires. In addition to demographic data, the Multiple Sclerosis Quality of Life-54 (MSQoL-54) instrument was used to determine how multiple sclerosis influences the quality of life of the studied women. Within the frame of this randomized controlled trial, the participants were divided into two equally sized groups (the case and the control group) in which the level of pain and the quality of life were evaluated. The case group exercised pain-managing Yoga methods for three months, keeping the pace of eight 90-minute sessions per month. The control participants were subjected to no intervention. One month after the Yoga therapy, the level of pain and the quality of life were evaluated in both groups and compared to the baseline data. Data were analyzed using SPSS software and paired t-tests. After the Yoga therapy, the case group showed a significant improvement in physical pain management (P=0.007) and the quality of life (P=0.001) as compared to the control group. The results showed that Yoga techniques can alleviate physical pain and improve the quality of life of multiple sclerosis patients.

Application of microscopy technique and high-performance liquid chromatography for quality assessment of the flower bud of Tussilago farfara L. (Kuandonghua)

PubMed Central

Li, Da; Liang, Li; Zhang, Jing; Kang, Tingguo

2015-01-01

Background: Quality control is one of the bottleneck problems limiting the application and development of traditional Chinese medicine (TCM). In recent years, microscopy and high-performance liquid chromatography (HPLC) techniques have been frequently applied in the quality control of TCM. However, studies combining conventional microscopy and HPLC techniques for the quality control of the flower bud of Tussilago farfara L. (Kuandonghua) have not been reported. Objective: This study was undertaken to evaluate the quality of the flower bud of T. farfara L. and to establish the relationships between the quantity of pollen grains and four main bioactive constituents: tussilagone, chlorogenic acid, rutin and isoquercitrin. Materials and Methods: In this study, microscopic examination was used to quantify microscopic characteristics of the flower bud of T. farfara L., and the chemical components were determined by HPLC. The data were analyzed by Statistical Package for the Social Sciences statistics software. Results: The results of the analysis showed that tussilagone, chlorogenic acid, rutin and isoquercitrin were significantly correlated with the quantity of pollen grains in the flower bud of T. farfara L. There is a positive correlation between them. From these results, it can be deduced that the flower bud of T. farfara L. with a greater quantity of pollen grains should be of better quality. Conclusion: The study showed that the established method can be helpful for evaluating the quality of the flower bud of T. farfara L. based on microscopic characteristic constants and chemical quantitation. PMID:26246737

[Coronary artery bypass surgery: methods of performance monitoring and quality control].

PubMed

Albert, A; Sergeant, P; Ennker, J

2009-10-01

The strength of coronary bypass operations depends on the preservation of their benefits regarding freedom of symptoms, quality of life and survival, over decades. Significant variability of the results of an operative intervention according to the hospital or the operating surgeon is considered a weakness in the procedure. The external quality insurance tries to reach a transparent service providing market through hospital ranking comparability. Widely available information and competition will promote the improvement of the whole quality. The structured dialog acts as a control instrument for the BQS (Federal Quality Insurance). It is launched in case of deviations from the standard references or statistically significant differences between the results of the operations in any hospital and the average notational results. In comparison to the external control the hospital internal control has greater ability to reach a medically useful statement regarding the results of the treatment and to correct the mistakes in time. An online information portal based on a departmental databank (DataWarehouse, DataMart) is an attractive solution for the physician in order to get transparently and timely informed about the variability in the performance.The individual surgeon significantly influences the short- and long-term treatment results. Accordingly, selection, targeted training and performance measurements are necessary.Strict risk management and failure analysis of individual cases are included in the methods of internal quality control aiming to identify and correct the inadequacies in the system and the course of treatment. According to the international as well as our own experience, at least 30% of the mortalities after bypass operations are avoidable. A functioning quality control is especially important in minimally invasive interventions because they are often technically more demanding in comparison to the conventional procedures. In the field of OPCAB surgery, the special advantages of the procedure can be utilised to reach a nearly complete avoidance of postoperative stroke through combining the procedure with aorta no-touch technique. The long-term success of the bypass operation depends on the type of bypass material in additions to many other factors. Both internal mammary arteries are considered the most durable.Using an operation preparation check contributes to the operative success.

Simultaneous digital quantification and fluorescence-based size characterization of massively parallel sequencing libraries.

PubMed

Laurie, Matthew T; Bertout, Jessica A; Taylor, Sean D; Burton, Joshua N; Shendure, Jay A; Bielas, Jason H

2013-08-01

Due to the high cost of failed runs and suboptimal data yields, quantification and determination of fragment size range are crucial steps in the library preparation process for massively parallel sequencing (or next-generation sequencing). Current library quality control methods commonly involve quantification using real-time quantitative PCR and size determination using gel or capillary electrophoresis. These methods are laborious and subject to a number of significant limitations that can make library calibration unreliable. Herein, we propose and test an alternative method for quality control of sequencing libraries using droplet digital PCR (ddPCR). By exploiting a correlation we have discovered between droplet fluorescence and amplicon size, we achieve the joint quantification and size determination of target DNA with a single ddPCR assay. We demonstrate the accuracy and precision of applying this method to the preparation of sequencing libraries.

A compilation and analysis of helicopter handling qualities data. Volume 2: Data analysis

NASA Technical Reports Server (NTRS)

Heffley, R. K.

1979-01-01

A compilation and an analysis of helicopter handling qualities data are presented. Multiloop manual control methods are used to analyze the descriptive data, stability derivatives, and transfer functions for a six degrees of freedom, quasi static model. A compensatory loop structure is applied to coupled longitudinal, lateral and directional equations in such a way that key handling qualities features are examined directly.

Results-driven approach to improving quality and productivity

Treesearch

John Dramm

2000-01-01

Quality control (QC) programs do not often realize their full potential. Elaborate and expensive QC programs can easily get side tracked by the process of building a program with promises of “Someday, this will all pay off.” Training employees in QC methods is no guarantee that quality will improve. Several documented cases show that such activity-centered efforts...

Readings on Managing Organizational Quality

DTIC Science & Technology

1990-05-01

Produc- tivify Review, Autumn, 1985. VI. Acknow ledg- Ishikawa , Kaoru . Guide to Quality Control. Tokyo: Asian Productivity Organization.m ents 1976. We are...indebted to many people for the develop- Ishikawa , Kaoru What is Total Quality Con- ment of the ideas expressed in this paper. Chief trol?: The...Developed by Kaoru Ishikawa , this di- Yes agram breaks the causes into general categories like methods. .............. materials, machines, and man, and

The Database Business: Managing Today--Planning for Tomorrow. Quality Assurance of Text and Image Databases at the U.S. Patent and Trademark Office.

ERIC Educational Resources Information Center

Grooms, David W.

1988-01-01

Discusses the quality controls imposed on text and image data that is currently being converted from paper to digital images by the Patent and Trademark Office. The methods of inspection used on text and on images are described, and the quality of the data delivered thus far is discussed. (CLB)

Identifying models of delivery, care domains and quality indicators relevant to palliative day services: a scoping review protocol.

PubMed

O'Connor, Seán R; Dempster, Martin; McCorry, Noleen K

2017-05-16

With an ageing population and increasing numbers of people with life-limiting illness, there is a growing demand for palliative day services. There is a need to measure and demonstrate the quality of these services, but there is currently little agreement on which aspects of care should be used to do this. The aim of the scoping review will be to map the extent, range and nature of the evidence around models of delivery, care domains and existing quality indicators used to evaluate palliative day services. Electronic databases (MEDLINE, EMBASE, CINAHL, PsycINFO, Cochrane Central Register of Controlled Trials) will be searched for evidence using consensus development methods; randomised or quasi-randomised controlled trials; mixed methods; and prospective, longitudinal or retrospective case-control studies to develop or test quality indicators for evaluating palliative care within non-residential settings, including day hospices and community or primary care settings. At least two researchers will independently conduct all searches, study selection and data abstraction procedures. Meta-analyses and statistical methods of synthesis are not planned as part of the review. Results will be reported using numerical counts, including number of indicators in each care domain and by using qualitative approach to describe important indicator characteristics. A conceptual model will also be developed to summarise the impact of different aspects of quality in a palliative day service context. Methodological quality relating to indicator development will be assessed using the Appraisal of Indicators through Research and Evaluation (AIRE) tool. Overall strength of evidence will be assessed using the Grading of Recommendations, Assessment, Development, and Evaluation (GRADE) system. Final decisions on quality assessment will be made via consensus between review authors. Identifying, developing and implementing evidence-based quality indicators is critical to the evaluation and continued improvement of palliative care. Review findings will be used to support clinicians and policymakers make decisions on which quality indicators are most appropriate for evaluating day services at the patient and service level, and to identify areas for further research.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Plemons, R.E.; Hopwood, W.H. Jr.; Hamilton, J.H.

For a number of years the Oak Ridge Y-12 Plant Laboratory has been analyzing coal predominately for the utilities department of the Y-12 Plant. All laboratory procedures, except a Leco sulfur method which used the Leco Instruction Manual as a reference, were written based on the ASTM coal analyses. Sulfur is analyzed at the present time by two methods, gravimetric and Leco. The laboratory has two major endeavors for monitoring the quality of its coal analyses. (1) A control program by the Plant Statistical Quality Control Department. Quality Control submits one sample for every nine samples submitted by the utilitiesmore » departments and the laboratory analyzes a control sample along with the utilities samples. (2) An exchange program with the DOE Coal Analysis Laboratory in Bruceton, Pennsylvania. The Y-12 Laboratory submits to the DOE Coal Laboratory, on even numbered months, a sample that Y-12 has analyzed. The DOE Coal Laboratory submits, on odd numbered months, one of their analyzed samples to the Y-12 Plant Laboratory to be analyzed. The results of these control and exchange programs are monitored not only by laboratory personnel, but also by Statistical Quality Control personnel who provide statistical evaluations. After analysis and reporting of results, all utilities samples are retained by the laboratory until the coal contracts have been settled. The utilities departments have responsibility for the initiation and preparation of the coal samples. The samples normally received by the laboratory have been ground to 4-mesh, reduced to 0.5-gallon quantities, and sealed in air-tight containers. Sample identification numbers and a Request for Analysis are generated by the utilities departments.« less

VQone MATLAB toolbox: A graphical experiment builder for image and video quality evaluations: VQone MATLAB toolbox.

PubMed

Nuutinen, Mikko; Virtanen, Toni; Rummukainen, Olli; Häkkinen, Jukka

2016-03-01

This article presents VQone, a graphical experiment builder, written as a MATLAB toolbox, developed for image and video quality ratings. VQone contains the main elements needed for the subjective image and video quality rating process. This includes building and conducting experiments and data analysis. All functions can be controlled through graphical user interfaces. The experiment builder includes many standardized image and video quality rating methods. Moreover, it enables the creation of new methods or modified versions from standard methods. VQone is distributed free of charge under the terms of the GNU general public license and allows code modifications to be made so that the program's functions can be adjusted according to a user's requirements. VQone is available for download from the project page (http://www.helsinki.fi/psychology/groups/visualcognition/).

Individual tree control

Treesearch

Harvey A. Holt

1989-01-01

Controlling individual unwanted trees in forest stands is a readily accepted method for improving the value of future harvests. The practice is especially important in mixed hardwood forests where species differ considerably in value and within species individual trees differ in quality. Individual stem control is a mechanical or chemical weeding operation that...

A new hyperspectral imaging based device for quality control in plastic recycling

NASA Astrophysics Data System (ADS)

Bonifazi, G.; D'Agostini, M.; Dall'Ava, A.; Serranti, S.; Turioni, F.

2013-05-01

The quality control of contamination level in the recycled plastics stream has been identified as an important key factor for increasing the value of the recycled material by both plastic recycling and compounder industries. Existing quality control methods for the detection of both plastics and non-plastics contaminants in the plastic waste streams at different stages of the industrial process (e.g. feed, intermediate and final products) are currently based on the manual collection from the stream of a sample and on the subsequent off-line laboratory analyses. The results of such analyses are usually available after some hours, or sometimes even some days, after the material has been processed. The laboratory analyses are time-consuming and expensive (both in terms of equipment cost and their maintenance and of labour cost).Therefore, a fast on-line assessment to monitor the plastic waste feed streams and to characterize the composition of the different plastic products, is fundamental to increase the value of secondary plastics. The paper is finalized to describe and evaluate the development of an HSI-based device and of the related software architectures and processing algorithms for quality assessment of plastics in recycling plants, with particular reference to polyolefins (PO). NIR-HSI sensing devices coupled with multivariate data analysis methods was demonstrated as an objective, rapid and non-destructive technique that can be used for on-line quality and process control in the recycling process of POs. In particular, the adoption of the previous mentioned HD&SW integrated architectures can provide a solution to one of the major problems of the recycling industry, which is the lack of an accurate quality certification of materials obtained by recycling processes. These results could therefore assist in developing strategies to certify the composition of recycled PO products.

Discussion of the quality control and performance testing of ultrasound diagnostic equipment

NASA Astrophysics Data System (ADS)

Jiang, Junjie

2018-03-01

In recent years, with the rapid development of ultrasonography, the application and popularization of new technology used in ultrasound equipment, the level of providing diagnostic information for doctors enhances unceasingly, which has become the indispensable diagnostic tool for medical institutions. The performance of equipment is directly related to the doctor’s diagnosis and the patient’s health, therefore, it is very important to choose a good method for quality control and performance testing.

Control method of Three-phase Four-leg converter based on repetitive control

NASA Astrophysics Data System (ADS)

Hui, Wang

2018-03-01

The research chose the magnetic levitation force of wind power generation system as the object. In order to improve the power quality problem caused by unbalanced load in power supply system, we combined the characteristics and repetitive control principle of magnetic levitation wind power generation system, and then an independent control strategy for three-phase four-leg converter was proposed. In this paper, based on the symmetric component method, the second order generalized integrator was used to generate the positive and negative sequence of signals, and the decoupling control was carried out under the synchronous rotating reference frame, in which the positive and negative sequence voltage is PI double closed loop, and a PI regulator with repetitive control was introduced to eliminate the static error regarding the fundamental frequency fluctuation characteristic of zero sequence component. The simulation results based on Matlab/Simulink show that the proposed control project can effectively suppress the disturbance caused by unbalanced loads and maintain the load voltage balance. The project is easy to be achieved and remarkably improves the quality of the independent power supply system.

An approach to quality and performance control in a computer-assisted clinical chemistry laboratory.

PubMed Central

Undrill, P E; Frazer, S C

1979-01-01

A locally developed, computer-based clinical chemistry laboratory system has been in operation since 1970. This utilises a Digital Equipment Co Ltd PDP 12 and an interconnected PDP 8/F computer. Details are presented of the performance and quality control techniques incorporated into the system. Laboratory performance is assessed through analysis of results from fixed-level control sera as well as from cumulative sum methods. At a simple level the presentation may be considered purely indicative, while at a more sophisticated level statistical concepts have been introduced to aid the laboratory controller in decision-making processes. PMID:438340

Method of control position of laser focus during surfacing teeth of cutters

NASA Astrophysics Data System (ADS)

Zvezdin, V. V.; Hisamutdinov, R. M.; Rakhimov, R. R.; Israfilov, I. H.; Akhtiamov, R. F.

2017-09-01

Providing the quality laser of surfacing the edges of teeth requires control not only the energy of the radiation parameters, but also the position of the focal spot. The control channel of position of laser focus during surfacing, which determines the parameters of quality of the deposited layer, was calculated in the work. The parameters of the active opto-electronic system for the subsystem adjust the focus position relative to the deposited layer with a laser illumination of the cutting edges the teeth cutters were calculated, the model of a control channel based on thermal phenomena occurring in the zone of surfacing was proposed.

Innovative application of the moisture analyzer for determination of dry mass content of processed cheese

NASA Astrophysics Data System (ADS)

Kowalska, Małgorzata; Janas, Sławomir; Woźniak, Magdalena

2018-04-01

The aim of this work was the presentation of an alternative method of determination of the total dry mass content in processed cheese. The authors claim that the presented method can be used in industry's quality control laboratories for routine testing and for quick in-process control. For the test purposes both reference method of determination of dry mass in processed cheese and moisture analyzer method were used. The tests were carried out for three different kinds of processed cheese. In accordance with the reference method, the sample was placed on a layer of silica sand and dried at the temperature of 102 °C for about 4 h. The moisture analyzer test required method validation, with regard to drying temperature range and mass of the analyzed sample. Optimum drying temperature of 110 °C was determined experimentally. For Hochland cream processed cheese sample, the total dry mass content, obtained using the reference method, was 38.92%, whereas using the moisture analyzer method, it was 38.74%. An average analysis time in case of the moisture analyzer method was 9 min. For the sample of processed cheese with tomatoes, the reference method result was 40.37%, and the alternative method result was 40.67%. For the sample of cream processed cheese with garlic the reference method gave value of 36.88%, and the alternative method, of 37.02%. An average time of those determinations was 16 min. Obtained results confirmed that use of moisture analyzer is effective. Compliant values of dry mass content were obtained for both of the used methods. According to the authors, the fact that the measurement took incomparably less time for moisture analyzer method, is a key criterion of in-process control and final quality control method selection.

Quality of anti-malarials collected in the private and informal sectors in Guyana and Suriname

PubMed Central

2012-01-01

Background Despite a significant reduction in the number of malaria cases in Guyana and Suriname, this disease remains a major problem in the interior of both countries, especially in areas with gold mining and logging operations, where malaria is endemic. National malaria control programmes in these countries provide treatment to patients with medicines that are procured and distributed through regulated processes in the public sector. However, availability to medicines in licensed facilities (private sector) and unlicensed facilities (informal sector) is common, posing the risk of access to and use of non-recommended treatments and/or poor quality products. Methods To assess the quality of circulating anti-malarial medicines, samples were purchased in the private and informal sectors of Guyana and Suriname in 2009. The sampling sites were selected based on epidemiological data and/or distance from health facilities. Samples were analysed for identity, content, dissolution or disintegration, impurities, and uniformity of dosage units or weight variation according to manufacturer, pharmacopeial, or other validated method. Results Quality issues were observed in 45 of 77 (58%) anti-malarial medicines sampled in Guyana of which 30 failed visual & physical inspection and 18 failed quality control tests. The proportion of monotherapy and ACT medicines failing quality control tests was 43% (13/30) and 11% (5/47) respectively. A higher proportion of medicines sampled from the private sector 34% (11/32) failed quality control tests versus 16% (7/45) in the informal sector. In Suriname, 58 medicines were sampled, of which 50 (86%) were Artecom®, the fixed-dose combination of piperaquine-dihydroartemisinin-trimethoprim co-blistered with a primaquine phosphate tablet. All Artecom samples were found to lack a label claim for primaquine, thus failing visual and physical inspection. Conclusions The findings of the studies in both countries point to significant problems with the quality of anti-malarial medicines available in private and informal sector facilities as well as the availability of therapy not compliant with national treatment guidelines. They also stress the need to strengthen regulatory control efforts on the availability of anti-malarial medicines in these sectors and in endemic areas. PMID:22704709

Use of near-infrared spectroscopy and multipoint measurements for quality control of pharmaceutical drug products.

PubMed

Boiret, Mathieu; Chauchard, Fabien

2017-01-01

Near-infrared (NIR) spectroscopy is a non-destructive analytical technique that enables better-understanding and optimization of pharmaceutical processes and final drug products. The use in line is often limited by acquisition speed and sampling area. This work focuses on performing a multipoint measurement at high acquisition speed at the end of the manufacturing process on a conveyor belt system to control both the distribution and the content of active pharmaceutical ingredient within final drug products, i.e., tablets. A specially designed probe with several collection fibers was developed for this study. By measuring spectral and spatial information, it provides physical and chemical knowledge on the final drug product. The NIR probe was installed on a conveyor belt system that enables the analysis of a lot of tablets. The use of these NIR multipoint measurement probes on a conveyor belt system provided an innovative method that has the potential to be used as a new paradigm to ensure the drug product quality at the end of the manufacturing process and as a new analytical method for the real-time release control strategy. Graphical abstract Use of near-infrared spectroscopy and multipoint measurements for quality control of pharmaceutical drug products.

Quality Space and Launch Requirements Addendum to AS9100C

DTIC Science & Technology

2015-03-05

45 8.9.1 Statistical Process Control (SPC) .......................................................................... 45 8.9.1.1 Out of Control...Systems Center SME Subject Matter Expert SOW Statement of Work SPC Statistical Process Control SPO System Program Office SRP Standard Repair...individual data exceeding the control limits. Control limits are developed using standard statistical methods or other approved techniques and are based on

Determining Directions of Ultrasound in Solids

NASA Technical Reports Server (NTRS)

Generazio, Edward R.; Roth, Don J.

1987-01-01

Ultrasound shadows cast by grooves. Improved method for determining direction of ultrasound in materials is shadow method using Scanning laser acoustic microscopy (SLAM). Direction of ultrasound calculated from dimensions of groove and portion of surface groove shields from ultrasound. Method has variety of applications in nontraditional quality-control applications.

First evaluation of automated specimen inoculation for wound swab samples by use of the Previ Isola system compared to manual inoculation in a routine laboratory: finding a cost-effective and accurate approach.

PubMed

Mischnik, Alexander; Mieth, Markus; Busch, Cornelius J; Hofer, Stefan; Zimmermann, Stefan

2012-08-01

Automation of plate streaking is ongoing in clinical microbiological laboratories, but evaluation for routine use is mostly open. In the present study, the recovery of microorganisms from the Previ Isola system plated polyurethane (PU) swab samples is compared to manually plated control viscose swab samples from wounds according to the CLSI procedure M40-A (quality control of microbiological transport systems). One hundred twelve paired samples (224 swabs) were analyzed. In 80/112 samples (71%), concordant culture results were obtained with the two methods. In 32/112 samples (29%), CFU recovery of microorganisms from the two methods was discordant. In 24 (75%) of the 32 paired samples with a discordant result, Previ Isola plated PU swabs were superior. In 8 (25%) of the 32 paired samples with a discordant result, control viscose swabs were superior. The quality of colony growth on culture media for further investigations was superior with Previ Isola inoculated plates compared to manual plating techniques. Gram stain results were concordant between the two methods in 62/112 samples (55%). In 50/112 samples (45%), the results of Gram staining were discordant between the two methods. In 34 (68%) of the 50 paired samples with discordant results, Gram staining of PU swabs was superior to that of control viscose swabs. In 16 (32%) of the 50 paired samples, Gram staining of control viscose swabs was superior to that of PU swabs. We report the first clinical evaluation of Previ Isola automated specimen inoculation for wound swab samples. This study suggests that use of an automated specimen inoculation system has good results with regard to CFU recovery, quality of Gram staining, and accuracy of diagnosis.

First Evaluation of Automated Specimen Inoculation for Wound Swab Samples by Use of the Previ Isola System Compared to Manual Inoculation in a Routine Laboratory: Finding a Cost-Effective and Accurate Approach

PubMed Central

Mieth, Markus; Busch, Cornelius J.; Hofer, Stefan; Zimmermann, Stefan

2012-01-01

Automation of plate streaking is ongoing in clinical microbiological laboratories, but evaluation for routine use is mostly open. In the present study, the recovery of microorganisms from the Previ Isola system plated polyurethane (PU) swab samples is compared to manually plated control viscose swab samples from wounds according to the CLSI procedure M40-A (quality control of microbiological transport systems). One hundred twelve paired samples (224 swabs) were analyzed. In 80/112 samples (71%), concordant culture results were obtained with the two methods. In 32/112 samples (29%), CFU recovery of microorganisms from the two methods was discordant. In 24 (75%) of the 32 paired samples with a discordant result, Previ Isola plated PU swabs were superior. In 8 (25%) of the 32 paired samples with a discordant result, control viscose swabs were superior. The quality of colony growth on culture media for further investigations was superior with Previ Isola inoculated plates compared to manual plating techniques. Gram stain results were concordant between the two methods in 62/112 samples (55%). In 50/112 samples (45%), the results of Gram staining were discordant between the two methods. In 34 (68%) of the 50 paired samples with discordant results, Gram staining of PU swabs was superior to that of control viscose swabs. In 16 (32%) of the 50 paired samples, Gram staining of control viscose swabs was superior to that of PU swabs. We report the first clinical evaluation of Previ Isola automated specimen inoculation for wound swab samples. This study suggests that use of an automated specimen inoculation system has good results with regard to CFU recovery, quality of Gram staining, and accuracy of diagnosis. PMID:22692745

High beam quality and high energy short-pulse laser with MOPA

NASA Astrophysics Data System (ADS)

Jin, Quanwei; Pang, Yu; Jiang, JianFeng; Tan, Liang; Cui, Lingling; Wei, Bin; Sun, Yinhong; Tang, Chun

2018-03-01

A high energy, high beam quality short-pulse diode-pumped Nd:YAG master oscillator power-amplifier (MOPA) laser with two amplifier stages is demonstrated. The two-rod birefringence compensation was used as beam quality controlling methods, which presents a short-pulse energy of 40 mJ with a beam quality value of M2 = 1.2 at a repetition rate of 400Hz. The MOPA system delivers a short-pulse energy of 712.5 mJ with a pulse width of 12.4 ns.The method of spherical aberration compensation is improved the beam quality, a M2 factor of 2.3 and an optical-to-optical efficiency of 27.7% is obtained at the maximum laser out power.The laser obtained 1.4J out energy with polarization integration.

Method Development and Monitoring of Cyanotoxins in Water ...

EPA Pesticide Factsheets

This presentation describes method development of two ambient water LC/MS/MS methods for microcystins, cylindrospermopsin and anatoxin-a. Ruggedness of the methods will be demonstrated by evaluation of quality control samples derived from various water bodies across the country. Presentation at the Central Regional meeting of the American Chemical Society ambient water methods development for cyanotoxins

30 CFR 250.302 - Definitions concerning air quality.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and 250.304 of this part: Air pollutant means any combination of agents for which the Environmental... shown by monitored data or which is calculated by air quality modeling (or other methods determined by... standards established by EPA. Best available control technology (BACT) means an emission limitation based on...

Evaluating the Accuracy of Common Runoff Estimation Methods for New Impervious Hot-Mix Asphalt

EPA Science Inventory

Accurately predicting runoff volume from impervious surfaces for water quality design events (e.g., 25.4 mm) is important for sizing green infrastructure stormwater control measures to meet water quality and infiltration design targets. The objective of this research was to quan...

46 CFR 160.049-5 - Inspections and tests. 1

Code of Federal Regulations, 2014 CFR

2014-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Specification for a Buoyant Cushion Plastic Foam § 160.049-5... maintain quality control of the materials used, manufacturing methods and the finished product so as to... samples and components produced to maintain the quality of the finished product. Records of tests...

46 CFR 160.049-5 - Inspections and tests. 1

Code of Federal Regulations, 2012 CFR

2012-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Specification for a Buoyant Cushion Plastic Foam § 160.049-5... maintain quality control of the materials used, manufacturing methods and the finished product so as to... samples and components produced to maintain the quality of the finished product. Records of tests...

46 CFR 160.049-5 - Inspections and tests. 1

Code of Federal Regulations, 2013 CFR

2013-10-01

...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Specification for a Buoyant Cushion Plastic Foam § 160.049-5... maintain quality control of the materials used, manufacturing methods and the finished product so as to... samples and components produced to maintain the quality of the finished product. Records of tests...

QTLs detected for individual sugars and soluble solids content in apple

USDA-ARS?s Scientific Manuscript database

Sweetness is one of the most important fruit quality traits in breeding programs, determining the overall quality and flavor-perception of apples. Selecting for this trait using conventional breeding methods is challenging due to the complexity of its genetic control. In order to improve the efficie...

Accountability Indicators from the Viewpoint of Statistical Method.

ERIC Educational Resources Information Center

Jordan, Larry

Few people seriously regard students as "products" coming off an educational assembly line, but notions about accountability and quality improvement in higher education are pervaded by manufacturing ideas and metaphors. Because numerical indicators of quality are inevitably expressed by trend lines or statistical control chars of some kind, they…

Performance-based quality assurance/quality control (QA/QC) acceptance procedures for in-place soil testing phase 3.

DOT National Transportation Integrated Search

2015-01-01

One of the objectives of this study was to evaluate soil testing equipment based on its capability of measuring in-place stiffness or modulus values. : As design criteria transition from empirical to mechanistic-empirical, soil test methods and equip...

Quantitative Analysis and Stability of the Rodenticide TETS ...

EPA Pesticide Factsheets

Journal Article The determination of the rodenticide tetramethylenedisulfotetramine (TETS) in drinking water is reportable through the use of automated sample preparation via solid phase extraction and detection using isotope dilution gas chromatography-mass spectrometry. The method was characterized over twenty-two analytical batches with quality control samples. Accuracies for low and high concentration quality control pools were 100 and 101%, respectively. The minimum reporting level (MRL) for TETS in this method is 0.50 ug/L. Five drinking waters representing a range of water quality parameters and disinfection practices were fortified with TETS at ten times the MRL and analyzed over a 28 day period to determine the stability of TETS in these waters. The amount of TETS measured in these samples averaged 100 ± 6% of the amount fortified suggesting that tap water samples may be held for up to 28 days prior to analysis.

What can we learn from a decade of database audits? The Duke Clinical Research Institute experience, 1997–2006

PubMed Central

Rostami, Reza; Nahm, Meredith; Pieper, Carl F.

2011-01-01

Background Despite a pressing and well-documented need for better sharing of information on clinical trials data quality assurance methods, many research organizations remain reluctant to publish descriptions of and results from their internal auditing and quality assessment methods. Purpose We present findings from a review of a decade of internal data quality audits performed at the Duke Clinical Research Institute, a large academic research organization that conducts data management for a diverse array of clinical studies, both academic and industry-sponsored. In so doing, we hope to stimulate discussions that could benefit the wider clinical research enterprise by providing insight into methods of optimizing data collection and cleaning, ultimately helping patients and furthering essential research. Methods We present our audit methodologies, including sampling methods, audit logistics, sample sizes, counting rules used for error rate calculations, and characteristics of audited trials. We also present database error rates as computed according to two analytical methods, which we address in detail, and discuss the advantages and drawbacks of two auditing methods used during this ten-year period. Results Our review of the DCRI audit program indicates that higher data quality may be achieved from a series of small audits throughout the trial rather than through a single large database audit at database lock. We found that error rates trended upward from year to year in the period characterized by traditional audits performed at database lock (1997–2000), but consistently trended downward after periodic statistical process control type audits were instituted (2001–2006). These increases in data quality were also associated with cost savings in auditing, estimated at 1000 hours per year, or the efforts of one-half of a full time equivalent (FTE). Limitations Our findings are drawn from retrospective analyses and are not the result of controlled experiments, and may therefore be subject to unanticipated confounding. In addition, the scope and type of audits we examine here are specific to our institution, and our results may not be broadly generalizable. Conclusions Use of statistical process control methodologies may afford advantages over more traditional auditing methods, and further research will be necessary to confirm the reliability and usability of such techniques. We believe that open and candid discussion of data quality assurance issues among academic and clinical research organizations will ultimately benefit the entire research community in the coming era of increased data sharing and re-use. PMID:19342467

Exploring in integrated quality evaluation of Chinese herbal medicines: the integrated quality index (IQI) for aconite.

PubMed

Zhang, Ding-kun; Wang, Jia-bo; Yang, Ming; Peng, Cheng; Xiao, Xiao-he

2015-07-01

Good medicinal herbs, good drugs. Good evaluation method and indices are the prerequisite of good medicinal herbs. However, there exist numerous indices for quality evaluation and control in Chinese medicinal materials. However, most of these indices are non-interrelated each other, as well as having little relationship with efficiency and safety. The results of different evaluatior methods may not be consistent, even contradictory. Considering the complex material properties of Chinese medicinal materials, single method and index is difficult to objectively and comprehensively reflect the quality. Therefore, it is essential to explore the integrated evaluation methods. In this paper, oriented by the integrated evaluation strategies for traditional Chinese medicine quality, a new method called integrated quality index (IQI) by the integration of empirical evaluation, chemical evaluation, and biological evaluation was proposed. In addition, a study case of hypertoxic herb Aconitum carmichaelii Debx. was provided to explain this method in detail. The results suggested that in the view of specifications, the average weight of Jiangyou aconite was the greatest, followed by Weishan aconite, Butuo aconite, Hanzhong aconite, and Anxian aconite; from the point of chemical components, Jiangyou aconite had the characteristic with strong efficacy and weak toxicity, next was Hanzhong aconite, Butuo aconite, Weishan aconite, and Anxian aconite; taking toxicity price as the index, Hanzhong aconite and Jiangyou aconite have the lower toxicity, while Butuo aconite, Weishan aconite, and Anxian aconite have the relatively higher one. After the normalization and integration of evaluation results, we calculated the IQI value of Jiangyou aconite, Hanzhong aconite, Butuo aconite, Weishan aconite, and Anxian aconite were 0.842 +/- 0.091, 0.597 +/- 0.047, 0.442 +/- 0.033, 0.454 +/- 0.038, 0.170 +/- 0.021, respectively. The quality of Jiangyou aconite is significantly better than the others (P < 0.05) followed by Hanzhong aconite, which is consistent with the traditional understanding of genuineness. It can be concluded that IQI achieves the integrated control and evaluation for the quality of Chinese medicinal materials, and it is an exploration for building the good medicinal herbs standards. In addition, IQI provides technical supports for the geoherbalism evaluation, selective breeding, the development of precision decoction pieces, high quality and favourable price in market circulation, and rational drug use.

An Angular Method with Position Control for Block Mesh Squareness Improvement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yao, J.; Stillman, D.

We optimize a target function de ned by angular properties with a position control term for a basic stencil with a block-structured mesh, to improve element squareness in 2D and 3D. Comparison with the condition number method shows that besides a similar mesh quality regarding orthogonality can be achieved as the former does, the new method converges faster and provides a more uniform global mesh spacing in our numerical tests.

Simultaneous determination of six active components by a single standard to determine multicomponents combined with fingerprint analysis for the quality control of Rhizoma Chuanxiong.

PubMed

He, Yufei; Li, Qing; Bi, Kaishun

2015-04-01

To control the quality of Rhizoma Chuanxiong, a method based on high-performance liquid chromatography method coupled with diode array detection was developed for the quantitative analysis of six active ingredients using a single standard to determine multi-components and chemical fingerprint analysis for the first time. The separation was performed on an Agilent Zorbax SB-C18 column by gradient elution with methanol and aqueous phase (containing 0.5% glacial acetic acid) at a flow rate of 1.0 mL/min. The UV wavelength was set at 274 nm. This assay was fully validated with respect to precision, repeatability, and accuracy. All calibration curves showed good linearity (R(2) > 0.9994) within test ranges. The limit of detection and limit of quantification were lower than 0.01 and 0.03 μg/mL, respectively. The relative standard deviation for repeatability and the intermediate precision of six analytes were less than 1.6 and 2.5%, respectively, the overall recovery was 96.1-103.1%. In addition, fingerprint chromatography using hierarchical clustering analysis and similarity analysis was performed to differentiate and classify the samples. The method described here could provide a more comprehensive and reasonable scientific assessment of the quality of Rhizoma Chuanxiong. Therefore, the strategy is feasible, credible, and is easily and effectively adapted for evaluating the quality control of Rhizoma Chuanxiong. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preanalytical errors in medical laboratories: a review of the available methodologies of data collection and analysis.

PubMed

West, Jamie; Atherton, Jennifer; Costelloe, Seán J; Pourmahram, Ghazaleh; Stretton, Adam; Cornes, Michael

2017-01-01

Preanalytical errors have previously been shown to contribute a significant proportion of errors in laboratory processes and contribute to a number of patient safety risks. Accreditation against ISO 15189:2012 requires that laboratory Quality Management Systems consider the impact of preanalytical processes in areas such as the identification and control of non-conformances, continual improvement, internal audit and quality indicators. Previous studies have shown that there is a wide variation in the definition, repertoire and collection methods for preanalytical quality indicators. The International Federation of Clinical Chemistry Working Group on Laboratory Errors and Patient Safety has defined a number of quality indicators for the preanalytical stage, and the adoption of harmonized definitions will support interlaboratory comparisons and continual improvement. There are a variety of data collection methods, including audit, manual recording processes, incident reporting mechanisms and laboratory information systems. Quality management processes such as benchmarking, statistical process control, Pareto analysis and failure mode and effect analysis can be used to review data and should be incorporated into clinical governance mechanisms. In this paper, The Association for Clinical Biochemistry and Laboratory Medicine PreAnalytical Specialist Interest Group review the various data collection methods available. Our recommendation is the use of the laboratory information management systems as a recording mechanism for preanalytical errors as this provides the easiest and most standardized mechanism of data capture.

[The Destruction of Pharmaceutical Products as an Element of the Efficiency of State Control (Supervision) Over the Circulation of Medicines].

PubMed

Bidarova, F N

2015-01-01

The modern system of state quality control over medicine makes it possible to reveal and withdraw drugs, that do not meet the requirements. However the problem of the turnover of substandard andfake drug and their destruction in the Russian Federation is still urgent. to evaluate the effectiveness of state quality control over medicine and the practice offake medicine destruction. data of the official websites of the Ministry of Health of the Russian Federation and the Republic of North Ossetia--Alania, Russian Sanitary Inspection, National Center of Quality control and Certification of Drugs were included in the investigation. Method of unrepeated samples was used in sociological investigations. 225 questionnaires have been worked out. The research was carried out in the North-Ossetian State Medical academy during the periodfrom 2013 to 2015 with the help of the National Center of Quality Control and Certification of Drugs. The shortcomings of the state quality control over the rules of fake drug destruction were studied. It was found out that the mechanism ofpermanent data collection monitoring of revealing, moving and destruction of substandard and fake drug destruction has not been determined. The ineffectiveness of controlling measures under the condition of critical legal base deficiency has been confirmed. The analysis of terminology characterizing the order of fake drug destruction was carried out. deficiencies related to the implementation of the state quality control over the fake drug destruction rules revealed during the course of investigations prove the necessity of adopting measures in creating new model of controlfunctions, increasing the results of activity.

Statistical methods for the quality control of steam cured concrete : final report.

DOT National Transportation Integrated Search

1971-01-01

Concrete strength test results from three prestressing plants utilizing steam curing were evaluated statistically in terms of the concrete as received and the effectiveness of the plants' steaming procedures. Control charts were prepared to show tren...

Nonlinear Multiobjective MPC-Based Optimal Operation of a High Consistency Refining System in Papermaking

DOE PAGES

Li, Mingjie; Zhou, Ping; Wang, Hong; ...

2017-09-19

As one of the most important unit in the papermaking industry, the high consistency (HC) refining system is confronted with challenges such as improving pulp quality, energy saving, and emissions reduction in its operation processes. Here in this correspondence, an optimal operation of HC refining system is presented using nonlinear multiobjective model predictive control strategies that aim at set-point tracking objective of pulp quality, economic objective, and specific energy (SE) consumption objective, respectively. First, a set of input and output data at different times are employed to construct the subprocess model of the state process model for the HC refiningmore » system, and then the Wiener-type model can be obtained through combining the mechanism model of Canadian Standard Freeness and the state process model that determines their structures based on Akaike information criterion. Second, the multiobjective optimization strategy that optimizes both the set-point tracking objective of pulp quality and SE consumption is proposed simultaneously, which uses NSGA-II approach to obtain the Pareto optimal set. Furthermore, targeting at the set-point tracking objective of pulp quality, economic objective, and SE consumption objective, the sequential quadratic programming method is utilized to produce the optimal predictive controllers. In conclusion, the simulation results demonstrate that the proposed methods can make the HC refining system provide a better performance of set-point tracking of pulp quality when these predictive controllers are employed. In addition, while the optimal predictive controllers orienting with comprehensive economic objective and SE consumption objective, it has been shown that they have significantly reduced the energy consumption.« less

Nonlinear Multiobjective MPC-Based Optimal Operation of a High Consistency Refining System in Papermaking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Mingjie; Zhou, Ping; Wang, Hong

As one of the most important unit in the papermaking industry, the high consistency (HC) refining system is confronted with challenges such as improving pulp quality, energy saving, and emissions reduction in its operation processes. Here in this correspondence, an optimal operation of HC refining system is presented using nonlinear multiobjective model predictive control strategies that aim at set-point tracking objective of pulp quality, economic objective, and specific energy (SE) consumption objective, respectively. First, a set of input and output data at different times are employed to construct the subprocess model of the state process model for the HC refiningmore » system, and then the Wiener-type model can be obtained through combining the mechanism model of Canadian Standard Freeness and the state process model that determines their structures based on Akaike information criterion. Second, the multiobjective optimization strategy that optimizes both the set-point tracking objective of pulp quality and SE consumption is proposed simultaneously, which uses NSGA-II approach to obtain the Pareto optimal set. Furthermore, targeting at the set-point tracking objective of pulp quality, economic objective, and SE consumption objective, the sequential quadratic programming method is utilized to produce the optimal predictive controllers. In conclusion, the simulation results demonstrate that the proposed methods can make the HC refining system provide a better performance of set-point tracking of pulp quality when these predictive controllers are employed. In addition, while the optimal predictive controllers orienting with comprehensive economic objective and SE consumption objective, it has been shown that they have significantly reduced the energy consumption.« less

Evaluation of variability and quality control procedures for a receptor-binding assay for paralytic shellfish poisoning toxins.

PubMed

Ruberu, S R; Langlois, G W; Masuda, M; Perera, S Kusum

2012-01-01

The receptor-binding assay (RBA) method for determining saxatoxin (STX) and its numerous analogues, which cause paralytic shellfish poisoning (PSP) in humans, was evaluated in a single laboratory study. Each step of the assay preparation procedure including the performance of the multi-detector TopCount® instrument was evaluated for its contribution to method variability. The overall inherent RBA variability was determined to be 17%. Variability within the 12 detectors was observed; however, there was no reproducible pattern in detector performance. This observed variability among detectors could be attributed to other factors, such as pipetting errors. In an attempt to reduce the number of plates rejected due to excessive variability in the method's quality control parameters, a statistical approach was evaluated using either Grubbs' test or the Student's t-test for rejecting outliers in the measurement of triplicate wells. This approach improved the ratio of accepted versus rejected plates, saving cost and time for rerunning the assay. However, the potential reduction in accuracy and the lack of improvement in precision suggests caution when using this approach. The current study has recommended an alternate quality control procedure for accepting or rejecting plates in place of the criteria currently used in the published assay, or the alternative of outlier testing. The recommended procedure involves the development of control charts to monitor the critical parameters identified in the published method (QC sample, EC₅₀, slope of calibration curve), with the addition of a fourth critical parameter which is the top value (100% binding) of the calibration curve.

Improving Quality of Seal Leak Test Product using Six Sigma

NASA Astrophysics Data System (ADS)

Luthfi Malik, Abdullah; Akbar, Muhammad; Irianto, Dradjad

2016-02-01

Seal leak test part is a polyurethane material-based product. Based on past data, defect level of this product was 8%, higher than the target of 5%. Quality improvement effort was done using six sigma method that included phases of define, measure, analyse, improve, and control. In the design phase, a Delphi method was used to identify factors that were critical to quality. In the measure phase, stability and process capability was measured. Fault tree analysis (FTA) and failure mode and effect analysis (FMEA) were used in the next phase to analize the root cause and to determine the priority issues. Improve phase was done by compiling, selecting, and designing alternative repair. Some improvement efforts were identified, i.e. (i) making a checklist for maintenance schedules, (ii) making written reminder form, (iii) modifying the SOP more detail, and (iv) performing a major service to the vacuum machine. To ensure the continuity of improvement efforts, some control activities were executed, i.e. (i) controlling, monitoring, documenting, and setting target frequently, (ii) implementing reward and punishment system, (iii) adding cleaning tool, and (iv) building six sigma organizational structure.

Apparatus and method for gelling liquefied gasses

NASA Technical Reports Server (NTRS)

Elliott, Adam (Inventor); DiSalvo, Roberto (Inventor); Shepherd, Phillip (Inventor); Kosier, Ryan (Inventor)

2011-01-01

A method and apparatus for gelling liquid propane and other liquefied gasses includes a temperature controlled churn mixer, vacuum pump, liquefied gas transfer tank, and means for measuring amount of material entering the mixer. The apparatus and method are particularly useful for the production of high quality rocket fuels and propellants.

Laboratory validation of four black carbon measurement methods for the determination of non-volatile particulate matter (PM) mass emissions . . .

EPA Science Inventory

A laboratory-scale experimental program was designed to standardize each of four black carbon measurement methods, provide appropriate quality assurance/control procedures for these techniques, and compare measurements made by these methods to a NIST traceable standard (filter gr...

[The continuous graphic presentation of interdepartmental results (author's transl)].

PubMed

Berger, J; Hirsch, H

1976-10-01

The results of interdepartmental determinations can be clearly presented in the laboratory in two ways: 1. Entry on a test card, according to Shewhart, as used in internal quality control. 2. Entry on a test card, constructed on the principle of the Cusum test. By the latter procedure, systematic errors are detected sooner than with the usual test card. A graphic variant of the Cusum test is described; a V-mask is not required; the card superficially resembles the usual control card, and the calculation time is minimal. This method may also be used to advantage in internal quality control.

[Cancer nursing care education programs: the effectiveness of different teaching methods].

PubMed

Cheng, Yun-Ju; Kao, Yu-Hsiu

2012-10-01

In-service education affects the quality of cancer care directly. Using classroom teaching to deliver in-service education is often ineffective due to participants' large workload and shift requirements. This study evaluated the learning effectiveness of different teaching methods in the dimensions of knowledge, attitude, and learning satisfaction. This study used a quasi-experimental study design. Participants were cancer ward nurses working at one medical center in northern Taiwan. Participants were divided into an experimental group and control group. The experimental group took an e-learning course and the control group took a standard classroom course using the same basic course material. Researchers evaluated the learning efficacy of each group using a questionnaire based on the quality of cancer nursing care learning effectiveness scale. All participants answered the questionnaire once before and once after completing the course. (1) Post-test "knowledge" scores for both groups were significantly higher than pre-test scores for both groups. Post-test "attitude" scores were significantly higher for the control group, while the experimental group reported no significant change. (2) after a covariance analysis of the pre-test scores for both groups, the post-test score for the experimental group was significantly lower than the control group in the knowledge dimension. Post-test scores did not differ significantly from pre-test scores for either group in the attitude dimension. (3) Post-test satisfaction scores between the two groups did not differ significantly with regard to teaching methods. The e-learning method, however, was demonstrated as more flexible than the classroom teaching method. Study results demonstrate the importance of employing a variety of teaching methods to instruct clinical nursing staff. We suggest that both classroom teaching and e-learning instruction methods be used to enhance the quality of cancer nursing care education programs. We also encourage that interactivity between student and instructor be incorporated into e-learning course designs to enhance effectiveness.

Characterizing SWCNT Dispersion in Polymer Composites

NASA Technical Reports Server (NTRS)

Lillehei, Peter T.; Kim, Jae-Woo; Gibbons, Luke; Park, Cheol

2007-01-01

The new wave of single wall carbon nanotube (SWCNT) infused composites will yield structurally sound multifunctional nanomaterials. The SWCNT network requires thorough dispersion within the polymer matrix in order to maximize the benefits of the nanomaterial. However, before any nanomaterials can be used in aerospace applications a means of quality assurance and quality control must be certified. Quality control certification requires a means of quantification, however, the measurement protocol mandates a method of seeing the dispersion first. We describe here the new tools that we have developed and implemented to first be able to see carbon nanotubes in polymers and second to measure or quantify the dispersion of the nanotubes.

Evaluating the quality of a cell counting measurement process via a dilution series experimental design.

PubMed

Sarkar, Sumona; Lund, Steven P; Vyzasatya, Ravi; Vanguri, Padmavathy; Elliott, John T; Plant, Anne L; Lin-Gibson, Sheng

2017-12-01

Cell counting measurements are critical in the research, development and manufacturing of cell-based products, yet determining cell quantity with accuracy and precision remains a challenge. Validating and evaluating a cell counting measurement process can be difficult because of the lack of appropriate reference material. Here we describe an experimental design and statistical analysis approach to evaluate the quality of a cell counting measurement process in the absence of appropriate reference materials or reference methods. The experimental design is based on a dilution series study with replicate samples and observations as well as measurement process controls. The statistical analysis evaluates the precision and proportionality of the cell counting measurement process and can be used to compare the quality of two or more counting methods. As an illustration of this approach, cell counting measurement processes (automated and manual methods) were compared for a human mesenchymal stromal cell (hMSC) preparation. For the hMSC preparation investigated, results indicated that the automated method performed better than the manual counting methods in terms of precision and proportionality. By conducting well controlled dilution series experimental designs coupled with appropriate statistical analysis, quantitative indicators of repeatability and proportionality can be calculated to provide an assessment of cell counting measurement quality. This approach does not rely on the use of a reference material or comparison to "gold standard" methods known to have limited assurance of accuracy and precision. The approach presented here may help the selection, optimization, and/or validation of a cell counting measurement process. Published by Elsevier Inc.

Does theatre improve the quality of life of people with dementia?

PubMed

van Dijk, A Marijke; van Weert, Julia C M; Dröes, Rose-Marie

2012-03-01

A new communication method, the "Veder method", has recently been developed. Caregivers are trained to apply this method in a group activity ("living-room theatre activity") for people with dementia in which theatrical stimuli are used in combination with proven emotion-oriented care methods. The aim of this exploratory study was to evaluate the added value of the Veder method group activity compared to a regular reminiscence group activity and to investigate whether professional carers can achieve the same effects with the Veder method as professional actors. A quasi-experimental three-group design was used. Experimental group 1 (E1; n = 65) joined a living-room theatre activity offered by trained professional caregivers. Experimental group 2 (E2; n = 31) joined a living-room theatre activity offered by professional actors. The control group (n = 55) received a usual reminiscence group activity. Behavior, mood and aspects of quality of life were measured using standardized observation scales at three points in time: (T1) pretest; (T2) during the intervention and; (T3) post-test, two hours after the intervention. During the intervention, significant differences were found in favor of the group that was offered a living-room theatre activity by actors (E2) on different aspects of behavior, mood and quality of life. At post-test, people in E2 were more alert compared to the control group. Moreover, they recalled more memories and showed less socially isolated behavior compared to the control group. This exploratory study shows that the Veder method has some clear positive effects on behavior and mood of people with dementia when applied by professional actors.

Comparative evaluation of different cultivars of Flos Chrysanthemi by an anti-inflammatory-based NF-κB reporter gene assay coupled to UPLC-Q/TOF MS with PCA and ANN.

PubMed

Han, Yanqi; Zhou, Mengge; Wang, Liqiang; Ying, Xuhui; Peng, Jiamin; Jiang, Min; Bai, Gang; Luo, Guoan

2015-11-04

Flos Chrysanthemi (FC), a commonly used traditional Chinese medicine, has five major cultivars ("Boju", "Chuju", "Gongju", "Hangbaiju" and "Huaiju") from different sources. However, the active constituents of these cultivars have not been studied or characterized with respect to their bioactivity, which is a serious problem when considering quality and safety. To evaluate the differences among the five cultivars of FC, and to establish a method for the standardization and quality control of FC related to its bioactivity. In this study, the different ingredients in five cultivars of FC were identified by UPLC-Q/TOF and PCA, and the anti-inflammatory ingredients of FC were predicted and screened by artificial neural network (ANN) and an NF-κB luciferase reporter gene assay system. Using this comprehensive method, we successfully screened the anti-inflammatory markers of different cultivars of FC. Nineteen marker ingredients were confirmed to contribute strongly to the cluster, and eleven compounds in the five cultivars of FC were found to exert potential anti-inflammatory effects. Among these compounds, the NF-κB inhibitor activity of apigenin-7-O-6″-malonyl-glucoside, luteolin-7-O-rutinoside, quercetin-7-O-galactoside, quercetin-3-O-glucoside, apigenin-7-O-rutinoside and apigenin-7-O-glucoside were first reported here. Chlorogenic acid, luteolin-7-O-glucoside, 3,5-dicaffeoylquinic acid and luteolin were confirmed to be the most important anti-inflammatory marker ingredients useful for the quality control of FC. The proposed efficient and systematic method is helpful for the standardization and quality control of FC. Moreover, this comprehensive strategy may prove to be a powerful technique for the rapid establishment of quality control procedures related to bioactivity for other herbal samples and foods. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

[Identification of impurity peaks in the HPLC chromatogram by LC-MS and two-dimensional chromatographic correlation spectroscopy].

PubMed

Chen, Zhen-Zhen; Zhang, Dou-Sheng; Wang, Nan; Feng, Fang; Hu, Chang-Qin

2012-04-01

A novel qualitative analytical method by using two-dimensional chromatographic correlation spectroscopy techniques for recognizing impurity peaks of HPLC methods of quality control and LC-MS chromatographic system was established. The structures of major degradation products of ceftizoxime and cefdinir were identified by LC-MS and MassWorks application; the standard chromatographic and spectral data of the degradation impurities were obtained by high-performance liquid chromatography with diode array detection. The impurity peaks of two-dimensional chromatography were matched by comparison of spectra and calculating correlation coefficients. Peaks in chromatography can be identified accurately and rapidly in different chromatographic systems such as column and mobile phase changed. The method provides a new way and thought to identify the peaks in quality control of impurities without reference impurity substances.

Quality control in urinalysis.

PubMed

Takubo, T; Tatsumi, N

1999-01-01

Quality control (QC) has been introduced in laboratories, and QC surveys in urinalysis have been performed by College of American Pathologist, by Japanese Association of Medical Technologists, by Osaka Medical Association and by manufacturers. QC survey in urinalysis for synthetic urine by the reagent strip and instrument made in same manufacturer, and by an automated urine cell analyser provided satisfactory results among laboratories. QC survey in urinalysis for synthetic urine by the reagent strips and instruments made by various manufacturers indicated differences in the determination values among manufacturers, and between manual and automated methods because the reagent strips and instruments have different characteristics, respectively. QC photo survey in urinalysis on the microscopic photos of urine sediment constituents indicated differences in the identification of cells among laboratories. From the results, it is necessary to standardize a reagent strip method, manual and automated methods, and synthetic urine.

[Quality control of Guci tablets using UPLC-ELSD fingerprint analysis coupled with chemometrics].

PubMed

Wang, Ya-Dan; Dai, Zhong; Sun, Cai-Lin; Wu, Xian-Fu; Ma, Shuang-Cheng

2018-03-01

Ultra-performance liquid chromatography-evaporative light scattering detection (UPLC-ELSD) fingerprint analysis method was established for quality control of Guci tablets. Chromatographic separation was performed on Waters Acquity UPLC BEH C₁₈ column (2.1 mm×100 mm, 1.7 μm) at 30 °C of column temperature. Acetonitrile-0.1% formic acid solution was adopted as mobile phase for gradient elution. The flow rate was set at 0.3 mL·min⁻¹, and the injection volume was 3 μL. Detection was carried out on an ELSD with a nitrogen pressure of 0.28 MPa, drift tube temperature of 60 °C, and gain of 400. A total of 39 batches of samples produced by six manufacturers were measured by using the above method and the data were analyzed by ChemPattern software. The peak present in more than 75% of the samples was defined as a common peak, and 30 common peaks were determined. Among them, 19 peaks were identified by rapid resolution liquid chromatography/tandem mass spectrometry (RRLC-MS/MS) method, 16 of which were confirmed by reference substances. The similarity of the tested samples was 0.47-0.98, suggesting that the quality of the samples from different manufacturers varied greatly. Furthermore, principal component analysis (PCA) and hierarchical analysis (HCA) were performed to clarify the main different components in samples. The results indicated that there might be some feeding problems about Paeoniae Radix Alba, Notoginseng Radix et Rhizoma, and Clematidis Radix et Rhizoma in a few manufacturers. This study provided some evidences for the overall quality control of Guci tablets, as well as its quality standard improvements. Copyright© by the Chinese Pharmaceutical Association.

A new validated method for the simultaneous determination of benzocaine, propylparaben and benzyl alcohol in a bioadhesive gel by HPLC.

PubMed

Pérez-Lozano, P; García-Montoya, E; Orriols, A; Miñarro, M; Ticó, J R; Suñé-Negre, J M

2005-10-04

A new HPLC-RP method has been developed and validated for the simultaneous determination of benzocaine, two preservatives (propylparaben (nipasol) and benzyl alcohol) and degradation products of benzocaine in a semisolid pharmaceutical dosage form (benzocaine gel). The method uses a Nucleosil 120 C18 column and gradient elution. The mobile phase consisted of a mixture of methanol and glacial acetic acid (10%, v/v) at different proportion according to a time-schedule programme, pumped at a flow rate of 2.0 ml min(-1). The DAD detector was set at 258 nm. The validation study was carried out fulfilling the ICH guidelines in order to prove that the new analytical method, meets the reliability characteristics, and these characteristics showed the capacity of analytical method to keep, throughout the time, the fundamental criteria for validation: selectivity, linearity, precision, accuracy and sensitivity. The method was applied during the quality control of benzocaine gel in order to quantify the drug (benzocaine), preservatives and degraded products and proved to be suitable for rapid and reliable quality control method.

Automatic quality control in clinical (1)H MRSI of brain cancer.

PubMed

Pedrosa de Barros, Nuno; McKinley, Richard; Knecht, Urspeter; Wiest, Roland; Slotboom, Johannes

2016-05-01

MRSI grids frequently show spectra with poor quality, mainly because of the high sensitivity of MRS to field inhomogeneities. These poor quality spectra are prone to quantification and/or interpretation errors that can have a significant impact on the clinical use of spectroscopic data. Therefore, quality control of the spectra should always precede their clinical use. When performed manually, quality assessment of MRSI spectra is not only a tedious and time-consuming task, but is also affected by human subjectivity. Consequently, automatic, fast and reliable methods for spectral quality assessment are of utmost interest. In this article, we present a new random forest-based method for automatic quality assessment of (1)H MRSI brain spectra, which uses a new set of MRS signal features. The random forest classifier was trained on spectra from 40 MRSI grids that were classified as acceptable or non-acceptable by two expert spectroscopists. To account for the effects of intra-rater reliability, each spectrum was rated for quality three times by each rater. The automatic method classified these spectra with an area under the curve (AUC) of 0.976. Furthermore, in the subset of spectra containing only the cases that were classified every time in the same way by the spectroscopists, an AUC of 0.998 was obtained. Feature importance for the classification was also evaluated. Frequency domain skewness and kurtosis, as well as time domain signal-to-noise ratios (SNRs) in the ranges 50-75 ms and 75-100 ms, were the most important features. Given that the method is able to assess a whole MRSI grid faster than a spectroscopist (approximately 3 s versus approximately 3 min), and without loss of accuracy (agreement between classifier trained with just one session and any of the other labelling sessions, 89.88%; agreement between any two labelling sessions, 89.03%), the authors suggest its implementation in the clinical routine. The method presented in this article was implemented in jMRUI's SpectrIm plugin. Copyright © 2016 John Wiley & Sons, Ltd.

Analysis of results obtained using the automatic chemical control of the quality of the water heat carrier in the drum boiler of the Ivanovo CHP-3 power plant

NASA Astrophysics Data System (ADS)

Larin, A. B.; Kolegov, A. V.

2012-10-01

Results of industrial tests of the new method used for the automatic chemical control of the quality of boiler water of the drum-type power boiler ( P d = 13.8 MPa) are described. The possibility of using an H-cationite column for measuring the electric conductivity of an H-cationized sample of boiler water over a long period of time is shown.

The quantitative control and matching of an optical false color composite imaging system

NASA Astrophysics Data System (ADS)

Zhou, Chengxian; Dai, Zixin; Pan, Xizhe; Li, Yinxi

1993-10-01

Design of an imaging system for optical false color composite (OFCC) capable of high-precision density-exposure time control and color balance is presented. The system provides high quality FCC image data that can be analyzed using a quantitative calculation method. The quality requirement to each part of the image generation system is defined, and the distribution of satellite remote sensing image information is analyzed. The proposed technology makes it possible to present the remote sensing image data more effectively and accurately.

Control Strategy of Active Power Filter Based on Modular Multilevel Converter

NASA Astrophysics Data System (ADS)

Xie, Xifeng

2018-03-01

To improve the capacity, pressure resistance and the equivalent switching frequency of active power filter (APF), a control strategy of APF based on Modular Multilevel Converter (MMC) is presented. In this Control Strategy, the indirect current control method is used to achieve active current and reactive current decoupling control; Voltage Balance Control Strategy is to stabilize sub-module capacitor voltage, the predictive current control method is used to Track and control of harmonic currents. As a result, the harmonic current is restrained, and power quality is improved. Finally, the simulation model of active power filter controller based on MMC is established in Matlab/Simulink, the simulation proves that the proposed strategy is feasible and correct.

Improvement of the customer satisfaction through Quality Assurance Matrix and QC-Story methods: A case study from automotive industry

NASA Astrophysics Data System (ADS)

Sicoe, G. M.; Belu, N.; Rachieru, N.; Nicolae, E. V.

2017-10-01

Presently, in the automotive industry, the tendency is to adapt permanently to the changes and introduce the market tendency in the new products that leads of the customer satisfaction. Many quality techniques were adopted in this field to continuous improvement of product and process quality and advantages were also gained. The present paper has focused on possibilities that offers the use of Quality Assurance Matrix (QAM) and Quality Control Story (QC Story) to provide largest protection against nonconformities in the production process, throughout a case study in the automotive industry. There is a direct relationship from the QAM to a QC Story analysis. The failures identified using QAM are treated with QC Story methodology. Using this methods, will help to decrease the PPM values and will increase the quality performance and the customer satisfaction.

Methods for collecting benthic invertebrate samples as part of the National Water-Quality Assessment Program

USGS Publications Warehouse

Cuffney, Thomas F.; Gurtz, Martin E.; Meador, Michael R.

1993-01-01

Benthic invertebrate communities are evaluated as part of the ecological survey component of the U.S. Geological Survey's National Water-Quality Assessment Program. These biological data are collected along with physical and chemical data to assess water-quality conditions and to develop an understanding of the factors that affect water-quality conditions locally, regionally, and nationally. The objectives of benthic invertebrate community characterizations are to (1) develop for each site a list of tax a within the associated stream reach and (2) determine the structure of benthic invertebrate communities within selected habitats of that reach. A nationally consistent approach is used to achieve these objectives. This approach provides guidance on site, reach, and habitat selection and methods and equipment for qualitative multihabitat sampling and semi-quantitative single habitat sampling. Appropriate quality-assurance and quality-control guidelines are used to maximize the ability to analyze data within and among study units.

Electron-beam lithography with character projection technique for high-throughput exposure with line-edge quality control

NASA Astrophysics Data System (ADS)

Ikeno, Rimon; Maruyama, Satoshi; Mita, Yoshio; Ikeda, Makoto; Asada, Kunihiro

2016-07-01

The high throughput of character projection (CP) electron-beam (EB) lithography makes it a promising technique for low-to-medium volume device fabrication with regularly arranged layouts, such as for standard-cell logics and memory arrays. However, non-VLSI applications such as MEMS and MOEMS may not be able to fully utilize the benefits of the CP method due to the wide variety of layout figures including curved and oblique edges. In addition, the stepwise shapes that appear because of the EB exposure process often result in intolerable edge roughness, which degrades device performances. In this study, we propose a general EB lithography methodology for such applications utilizing a combination of the CP and variable-shaped beam methods. In the process of layout data conversion with CP character instantiation, several control parameters were optimized to minimize the shot count, improve the edge quality, and enhance the overall device performance. We have demonstrated EB shot reduction and edge-quality improvement with our methodology by using a leading-edge EB exposure tool, ADVANTEST F7000S-VD02, and a high-resolution hydrogen silsesquioxane resist. Atomic force microscope observations were used to analyze the resist edge profiles' quality to determine the influence of the control parameters used in the data conversion process.

Technology transfer through a network of standard methods and recommended practices - The case of petrochemicals

NASA Astrophysics Data System (ADS)

Batzias, Dimitris F.; Karvounis, Sotirios

2012-12-01

Technology transfer may take place in parallel with cooperative action between companies participating in the same organizational scheme or using one another as subcontractor (outsourcing). In this case, cooperation should be realized by means of Standard Methods and Recommended Practices (SRPs) to achieve (i) quality of intermediate/final products according to specifications and (ii) industrial process control as required to guarantee such quality with minimum deviation (corresponding to maximum reliability) from preset mean values of representative quality parameters. This work deals with the design of the network of SRPs needed in each case for successful cooperation, implying also the corresponding technology transfer, effectuated through a methodological framework developed in the form of an algorithmic procedure with 20 activity stages and 8 decision nodes. The functionality of this methodology is proved by presenting the path leading from (and relating) a standard test method for toluene, as petrochemical feedstock in the toluene diisocyanate production, to the (6 generations distance upstream) performance evaluation of industrial process control systems (ie., from ASTM D5606 to BS EN 61003-1:2004 in the SRPs network).

Automatic initialization and quality control of large-scale cardiac MRI segmentations.

PubMed

Albà, Xènia; Lekadir, Karim; Pereañez, Marco; Medrano-Gracia, Pau; Young, Alistair A; Frangi, Alejandro F

2018-01-01

Continuous advances in imaging technologies enable ever more comprehensive phenotyping of human anatomy and physiology. Concomitant reduction of imaging costs has resulted in widespread use of imaging in large clinical trials and population imaging studies. Magnetic Resonance Imaging (MRI), in particular, offers one-stop-shop multidimensional biomarkers of cardiovascular physiology and pathology. A wide range of analysis methods offer sophisticated cardiac image assessment and quantification for clinical and research studies. However, most methods have only been evaluated on relatively small databases often not accessible for open and fair benchmarking. Consequently, published performance indices are not directly comparable across studies and their translation and scalability to large clinical trials or population imaging cohorts is uncertain. Most existing techniques still rely on considerable manual intervention for the initialization and quality control of the segmentation process, becoming prohibitive when dealing with thousands of images. The contributions of this paper are three-fold. First, we propose a fully automatic method for initializing cardiac MRI segmentation, by using image features and random forests regression to predict an initial position of the heart and key anatomical landmarks in an MRI volume. In processing a full imaging database, the technique predicts the optimal corrective displacements and positions in relation to the initial rough intersections of the long and short axis images. Second, we introduce for the first time a quality control measure capable of identifying incorrect cardiac segmentations with no visual assessment. The method uses statistical, pattern and fractal descriptors in a random forest classifier to detect failures to be corrected or removed from subsequent statistical analysis. Finally, we validate these new techniques within a full pipeline for cardiac segmentation applicable to large-scale cardiac MRI databases. The results obtained based on over 1200 cases from the Cardiac Atlas Project show the promise of fully automatic initialization and quality control for population studies. Copyright © 2017 Elsevier B.V. All rights reserved.

Practical Considerations for Optic Nerve Estimation in Telemedicine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karnowski, Thomas Paul; Aykac, Deniz; Chaum, Edward

The projected increase in diabetes in the United States and worldwide has created a need for broad-based, inexpensive screening for diabetic retinopathy (DR), an eye disease which can lead to vision impairment. A telemedicine network with retina cameras and automated quality control, physiological feature location, and lesion / anomaly detection is a low-cost way of achieving broad-based screening. In this work we report on the effect of quality estimation on an optic nerve (ON) detection method with a confidence metric. We report on an improvement of the fusion technique using a data set from an ophthalmologists practice then show themore » results of the method as a function of image quality on a set of images from an on-line telemedicine network collected in Spring 2009 and another broad-based screening program. We show that the fusion method, combined with quality estimation processing, can improve detection performance and also provide a method for utilizing a physician-in-the-loop for images that may exceed the capabilities of automated processing.« less

16 CFR 1000.29 - Directorate for Engineering Sciences.

Code of Federal Regulations, 2010 CFR

2010-01-01

... standards, product safety tests and test methods, performance criteria, design specifications, and quality control standards for consumer products, based on engineering and scientific methods. It conducts... consumer interest groups. The Directorate conducts human factors studies and research of consumer product...

16 CFR 1000.29 - Directorate for Engineering Sciences.

Code of Federal Regulations, 2012 CFR

2012-01-01

... standards, product safety tests and test methods, performance criteria, design specifications, and quality control standards for consumer products, based on engineering and scientific methods. It conducts... consumer interest groups. The Directorate conducts human factors studies and research of consumer product...

Numerical simulation of intelligent compaction technology for construction quality control.

DOT National Transportation Integrated Search

2015-02-01

For eciently updating models of large-scale structures, the response surface (RS) method based on radial basis : functions (RBFs) is proposed to model the input-output relationship of structures. The key issues for applying : the proposed method a...

[Effect analysis on the two total load control methods for poisonous heavy metals].

PubMed

Fu, Guo-Wei

2012-12-01

Firstly it should be made clear that implementation of source total load control for the first type of pollutants is necessary for environmental pollution control legislation and economic structure regulation. This kind of surveillance method has been more practical to be implemented since the Manual of the Industry Discharge Coefficient of First National Pollution Sources Investigation was published. The source total load control and water environment total load control are independent of each other and none of them is redundant, on the other side they can be complementary to each other. In the present, some local planning managers are blurring and confusing the contents and styles of the two surveillance methods. They just use the water total load control to manage all the pollutants, and source total load control is discarded, which results in the loss of control for the first type of pollutants especially for the drinking water source surveillance. There is a big difference between the water quality standards and the water environmental background concentration values for the first type of pollutants in the Environmental quality standard for surface water (GB 3838-88), which means that there are problems such as "relaxing the pollutant discharge permit" and "risk induced by valence state change". Taking an enterprise with 10t electrolytic lead production capacity as an example, there is a big difference between the allowable lead discharged loads by the two total load surveillance methods. In summary, it will bring a lot of harmful effects if the water total load control is implemented for the two types of pollutants, so the source total load control and water environmental total load control should be implemented strictly at the same time.

Global chemical profiling based quality evaluation approach of rhubarb using ultra performance liquid chromatography with tandem quadrupole time-of-flight mass spectrometry.

PubMed

Zhang, Li; Liu, Haiyu; Qin, Lingling; Zhang, Zhixin; Wang, Qing; Zhang, Qingqing; Lu, Zhiwei; Wei, Shengli; Gao, Xiaoyan; Tu, Pengfei

2015-02-01

A global chemical profiling based quality evaluation approach using ultra performance liquid chromatography with tandem quadrupole time-of-flight mass spectrometry was developed for the quality evaluation of three rhubarb species, including Rheum palmatum L., Rheum tanguticum Maxim. ex Balf., and Rheum officinale Baill. Considering that comprehensive detection of chemical components is crucial for the global profile, a systemic column performance evaluation method was developed. Based on this, a Cortecs column was used to acquire the chemical profile, and Chempattern software was employed to conduct similarity evaluation and hierarchical cluster analysis. The results showed R. tanguticum could be differentiated from R. palmatum and R. officinale at the similarity value 0.65, but R. palmatum and R. officinale could not be distinguished effectively. Therefore, a common pattern based on three rhubarb species was developed to conduct the quality evaluation, and the similarity value 0.50 was set as an appropriate threshold to control the quality of rhubarb. A total of 88 common peaks were identified by their accurate mass and fragmentation, and partially verified by reference standards. Through the verification, the newly developed method could be successfully used for evaluating the holistic quality of rhubarb. It would provide a reference for the quality control of other herbal medicines. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects of motivational enhancement therapy plus cognitive behaviour therapy on depressive symptoms and health-related quality of life in adults with type II diabetes mellitus: a randomised controlled trial.

PubMed

Huang, Chiung-Yu; Lai, Hui-Ling; Chen, Chun-I; Lu, Yung-Chuan; Li, Su-Chen; Wang, Long-Whou; Su, Yi

2016-05-01

This paper evaluates the effectiveness of motivational enhancement therapy plus cognitive behavioural therapy on depressive symptoms, glycosylated haemoglobin, fasting glucose, body mass index (BMI), and health-related quality of life in type II diabetes patients. A controlled trial was conducted to compare patients who received the behavioural intervention with untreated controls on measures of health outcomes. A total of 31 intervention group participants and 30 controls were selected from patients that met the inclusion criteria from a hospital-based endocrinology outpatient department. The outcome measures including depressive symptoms, glycosylated haemoglobin, fasting glucose, BMI, and both physical and mental quality of life were collected before (T1), after (T2), and after 90 days (T3) following the intervention. The experimental group showed a significant reduction in glycosylated haemoglobin, fasting glucose, and depressive symptoms and a significant increase in physical quality of life and mental quality of life at T2 and T3, while patients in the control group with usual care showed no changes over time. The behavioural intervention facilitated a significant improvement in psychological adjustment and glycemic control, thus strengthening diabetes control skills and leading to healthy outcomes. It is feasible that nurses and psychiatrists can deliver the behavioural intervention for diabetes patients to decrease their depressive symptoms. Sharing discussion and problem-solving experiences is particularly helpful method for self-control, and these will be beneficially influential on further research.

Effect of a facility-based multifaceted intervention on the quality of obstetrical care: a cluster randomized controlled trial in Mali and Senegal

PubMed Central

2013-01-01

Background Maternal mortality in referral hospitals in Mali and Senegal surpasses 1% of obstetrical admissions. Poor quality obstetrical care contributes to high maternal mortality; however, poor care is often linked to insufficient hospital resources. One promising method to improve obstetrical care is maternal death review. With a cluster randomized trial, we assessed whether an intervention, based on maternal death review, could improve obstetrical quality of care. Methods The trial began with a pre-intervention year (2007), followed by two years of intervention activities and a post-intervention year. We measured obstetrical quality of care in the post-intervention year using a criterion-based clinical audit (CBCA). We collected data from 32 of the 46 trial hospitals (16 in each trial arm) and included 658 patients admitted to the maternity unit with a trial of labour. The CBCA questionnaire measured 5 dimensions of care- patient history, clinical examination, laboratory examination, delivery care and postpartum monitoring. We used adjusted mixed models to evaluate differences in CBCA scores by trial arms and examined how levels of hospital human and material resources affect quality of care differences associated with the intervention. Results For all women, the mean percentage of care criteria met was 66.3 (SD 13.5). There were significantly greater mean CBCA scores in women treated at intervention hospitals (68.2) compared to control hospitals (64.5). After adjustment, women treated at intervention sites had 5 points’ greater scores than those at control sites. This difference was mostly attributable to greater clinical examination and post-partum monitoring scores. The association between the intervention and quality of care was the same, irrespective of the level of resources available to a hospital; however, as resources increased, so did quality of care scores in both arms of the trial. Trial registration The QUARITE trial is registered on the Current Controlled Trials website under ISRCTN46950658 PMID:23351269

Application of miniaturized near-infrared spectroscopy for quality control of extemporaneous orodispersible films.

PubMed

Foo, Wen Chin; Widjaja, Effendi; Khong, Yuet Mei; Gokhale, Rajeev; Chan, Sui Yung

2018-02-20

Extemporaneous oral preparations are routinely compounded in the pharmacy due to a lack of suitable formulations for special populations. Such small-scale pharmacy preparations also present an avenue for individualized pharmacotherapy. Orodispersible films (ODF) have increasingly been evaluated as a suitable dosage form for extemporaneous oral preparations. Nevertheless, as with all other extemporaneous preparations, safety and quality remain a concern. Although the United States Pharmacopeia (USP) recommends analytical testing of compounded preparations for quality assurance, pharmaceutical assays are typically not routinely performed for such non-sterile pharmacy preparations, due to the complexity and high cost of conventional assay methods such as high performance liquid chromatography (HPLC). Spectroscopic methods including Raman, infrared and near-infrared spectroscopy have been successfully applied as quality control tools in the industry. The state-of-art benchtop spectrometers used in those studies have the advantage of superior resolution and performance, but are not suitable for use in a small-scale pharmacy setting. In this study, we investigated the application of a miniaturized near infrared (NIR) spectrometer as a quality control tool for identification and quantification of drug content in extemporaneous ODFs. Miniaturized near infrared (NIR) spectroscopy is suitable for small-scale pharmacy applications in view of its small size, portability, simple user interface, rapid measurement and real-time prediction results. Nevertheless, the challenge with miniaturized NIR spectroscopy is its lower resolution compared to state-of-art benchtop equipment. We have successfully developed NIR spectroscopy calibration models for identification of ODFs containing five different drugs, and quantification of drug content in ODFs containing 2-10mg ondansetron (OND). The qualitative model for drug identification produced 100% prediction accuracy. The quantitative model to predict OND drug content in ODFs was divided into two calibrations for improved accuracy: Calibration I and II covered the 2-4mg and 4-10mg ranges respectively. Validation was performed for method accuracy, linearity and precision. In conclusion, this study demonstrates the feasibility of miniaturized NIR spectroscopy as a quality control tool for small-scale, pharmacy preparations. Due to its non-destructive nature, every dosage unit can be tested thus affording positive impact on patient safety. Copyright © 2017 Elsevier B.V. All rights reserved.

Microbiological methods for the water recovery systems test, revision 1.1

NASA Technical Reports Server (NTRS)

Rhoads, Tim; Kilgore, M. V., Jr.; Mikell, A. T., Jr.

1990-01-01

Current microbiological parameters specified to verify microbiological quality of Space Station Freedom water quality include the enumeration of total bacteria, anaerobes, aerobes, yeasts and molds, enteric bacteria, gram positives, gram negatives, and E. coli. In addition, other parameters have been identified as necessary to support the Water Recovery Test activities to be conducted at the NASA/MSFC later this year. These other parameters include aerotolerant eutrophic mesophiles, legionellae, and an additional method for heterotrophic bacteria. If inter-laboratory data are to be compared to evaluate quality, analytical methods must be eliminated as a variable. Therefore, each participating laboratory must utilize the same analytical methods and procedures. Without this standardization, data can be neither compared nor validated between laboratories. Multiple laboratory participation represents a conservative approach to insure quality and completeness of data. Invariably, sample loss will occur in transport and analyses. Natural variance is a reality on any test of this magnitude and is further enhanced because biological entities, capable of growth and death, are specific parameters of interest. The large variation due to the participation of human test subjects has been noted with previous testing. The resultant data might be dismissed as 'out of control' unless intra-laboratory control is included as part of the method or if participating laboratories are not available for verification. The purpose of this document is to provide standardized laboratory procedures for the enumeration of certain microorganisms in water and wastewater specific to the water recovery systems test. The document consists of ten separate cultural methods and one direct count procedure. It is not intended nor is it implied to be a complete microbiological methods manual.

A systematic review of the quality of statistical methods employed for analysing quality of life data in cancer randomised controlled trials.

PubMed

Hamel, Jean-Francois; Saulnier, Patrick; Pe, Madeline; Zikos, Efstathios; Musoro, Jammbe; Coens, Corneel; Bottomley, Andrew

2017-09-01

Over the last decades, Health-related Quality of Life (HRQoL) end-points have become an important outcome of the randomised controlled trials (RCTs). HRQoL methodology in RCTs has improved following international consensus recommendations. However, no international recommendations exist concerning the statistical analysis of such data. The aim of our study was to identify and characterise the quality of the statistical methods commonly used for analysing HRQoL data in cancer RCTs. Building on our recently published systematic review, we analysed a total of 33 published RCTs studying the HRQoL methods reported in RCTs since 1991. We focussed on the ability of the methods to deal with the three major problems commonly encountered when analysing HRQoL data: their multidimensional and longitudinal structure and the commonly high rate of missing data. All studies reported HRQoL being assessed repeatedly over time for a period ranging from 2 to 36 months. Missing data were common, with compliance rates ranging from 45% to 90%. From the 33 studies considered, 12 different statistical methods were identified. Twenty-nine studies analysed each of the questionnaire sub-dimensions without type I error adjustment. Thirteen studies repeated the HRQoL analysis at each assessment time again without type I error adjustment. Only 8 studies used methods suitable for repeated measurements. Our findings show a lack of consistency in statistical methods for analysing HRQoL data. Problems related to multiple comparisons were rarely considered leading to a high risk of false positive results. It is therefore critical that international recommendations for improving such statistical practices are developed. Copyright © 2017. Published by Elsevier Ltd.

Developmental validation of a Nextera XT mitogenome Illumina MiSeq sequencing method for high-quality samples.

PubMed

Peck, Michelle A; Sturk-Andreaggi, Kimberly; Thomas, Jacqueline T; Oliver, Robert S; Barritt-Ross, Suzanne; Marshall, Charla

2018-05-01

Generating mitochondrial genome (mitogenome) data from reference samples in a rapid and efficient manner is critical to harnessing the greater power of discrimination of the entire mitochondrial DNA (mtDNA) marker. The method of long-range target enrichment, Nextera XT library preparation, and Illumina sequencing on the MiSeq is a well-established technique for generating mitogenome data from high-quality samples. To this end, a validation was conducted for this mitogenome method processing up to 24 samples simultaneously along with analysis in the CLC Genomics Workbench and utilizing the AQME (AFDIL-QIAGEN mtDNA Expert) tool to generate forensic profiles. This validation followed the Federal Bureau of Investigation's Quality Assurance Standards (QAS) for forensic DNA testing laboratories and the Scientific Working Group on DNA Analysis Methods (SWGDAM) validation guidelines. The evaluation of control DNA, non-probative samples, blank controls, mixtures, and nonhuman samples demonstrated the validity of this method. Specifically, the sensitivity was established at ≥25 pg of nuclear DNA input for accurate mitogenome profile generation. Unreproducible low-level variants were observed in samples with low amplicon yields. Further, variant quality was shown to be a useful metric for identifying sequencing error and crosstalk. Success of this method was demonstrated with a variety of reference sample substrates and extract types. These studies further demonstrate the advantages of using NGS techniques by highlighting the quantitative nature of heteroplasmy detection. The results presented herein from more than 175 samples processed in ten sequencing runs, show this mitogenome sequencing method and analysis strategy to be valid for the generation of reference data. Copyright © 2018 Elsevier B.V. All rights reserved.

Water quality and nitrogen mass loss from anaerobic lagoon columns receiving pretreated influent

USDA-ARS?s Scientific Manuscript database

Control methods are needed to abate ammonia losses from swine anaerobic lagoons to reduce contribution of confined swine operations to air pollution. In a 15-month meso-scale column study, we evaluated the effect of manure pretreatment on water quality, reduction of N losses, and sludge accumulation...

Radiation Safety and Quality Assurance in North American Dental Schools.

ERIC Educational Resources Information Center

Farman, Allan G.; Hines, Vickie G.

1986-01-01

A survey of dental schools that revealed processing quality control and routine maintenance checks on x-ray generators are being carried out in a timely manner is discussed. However, methods for reducing patient exposure to radiation are not being fully implemented, and some dental students are being exposed to x-rays. (Author/MLW)

A six sigma review of miniature optics alignment

NASA Astrophysics Data System (ADS)

Tesar, John

2009-08-01

The key to high quality optics is a set of guidelines. Create an understanding of the Criteria for Quality. Focus on understanding and controlling process variation. Examine verification and validation of methods. Take a view of the horizon as well as drilling down so you know when to put down the shovel.

Stressor-response modeling using the 2D water quality model and regression trees to predict chlorophyll-a in a reservoir system

USDA-ARS?s Scientific Manuscript database

In order to control algal blooms, stressor-response relationships between water quality metrics, environmental variables, and algal growth should be understood and modeled. Machine-learning methods were suggested to express stressor-response relationships found by application of mechanistic water qu...

Adult Day Health Center Participation and Health-Related Quality of Life

ERIC Educational Resources Information Center

Schmitt, Eva M.; Sands, Laura P.; Weiss, Sara; Dowling, Glenna; Covinsky, Kenneth

2010-01-01

Purpose: The purpose of this study was to assess the association between Adult Day Health Center (ADHC) participation and health-related quality of life. Design and Methods: Case-controlled prospective study utilizing the Medical Outcomes Survey Form 36 (SF-36) to compare newly enrolled participants from 16 ADHC programs with comparable…

An introduction to statistical process control in research proteomics.

PubMed

Bramwell, David

2013-12-16

Statistical process control is a well-established and respected method which provides a general purpose, and consistent framework for monitoring and improving the quality of a process. It is routinely used in many industries where the quality of final products is critical and is often required in clinical diagnostic laboratories [1,2]. To date, the methodology has been little utilised in research proteomics. It has been shown to be capable of delivering quantitative QC procedures for qualitative clinical assays [3] making it an ideal methodology to apply to this area of biological research. To introduce statistical process control as an objective strategy for quality control and show how it could be used to benefit proteomics researchers and enhance the quality of the results they generate. We demonstrate that rules which provide basic quality control are easy to derive and implement and could have a major impact on data quality for many studies. Statistical process control is a powerful tool for investigating and improving proteomics research work-flows. The process of characterising measurement systems and defining control rules forces the exploration of key questions that can lead to significant improvements in performance. This work asserts that QC is essential to proteomics discovery experiments. Every experimenter must know the current capabilities of their measurement system and have an objective means for tracking and ensuring that performance. Proteomic analysis work-flows are complicated and multi-variate. QC is critical for clinical chemistry measurements and huge strides have been made in ensuring the quality and validity of results in clinical biochemistry labs. This work introduces some of these QC concepts and works to bridge their use from single analyte QC to applications in multi-analyte systems. This article is part of a Special Issue entitled: Standardization and Quality Control in Proteomics. Copyright © 2013 The Author. Published by Elsevier B.V. All rights reserved.

Microbiological Surveillance and State of the Art Technological Strategies for the Prevention of Dialysis Water Pollution

PubMed Central

Bolasco, Piergiorgio; Contu, Antonio; Meloni, Patrizia; Vacca, Dorio; Galfrè, Andrea

2012-01-01

Methods: The present report attempts to illustrate the positive impact on the microbiological quality of dialysis patients over a 15-year period through the progressive implementation of state-of-the-art technological strategies and the optimization of microbiological surveillance procedures in five dialysis units in Sardinia. Results: Following on better microbiological, quality controls of dialysis water and improvement of procedures and equipment, a drastic improvement of microbiological water quality was observed in a total of 945 samples. The main aim was to introduce the use of microbiological culture methods as recommended by the most important guidelines. The microbiological results obtained have led to a progressive refining of controls and introduction of new materials and equipment, including two-stage osmosis and piping distribution rings featuring a greater capacity to prevent biofilm adhesion. The actions undertaken have resulted in unexpected quality improvements. Conclusions: Dialysis water should be viewed by the nephrologist as a medicinal product exerting a demonstrable positive impact on microinflammation in dialysis patients. A synergic effort between nephrologists and microbiologists undoubtedly constitutes the most effective means of preventing dialysis infections. PMID:23066395

Regardless-of-Speed Superconducting LSM Controlled-Repulsive MAGLEV Vehicle

NASA Technical Reports Server (NTRS)

Yoshida, Kinjiro; Egashira, Tatsuya; Hirai, Ryuichi

1996-01-01

This paper proposes a new repulsive Maglev vehicle which a superconducting linear synchronous motor (LSM) can levitate and propel simultaneously, independently of the vehicle speeds. The combined levitation and propulsion control is carried out by controlling mechanical-load angle and armature-current. Dynamic simulations show successful operations with good ride-quality by using a compact control method proposed here.

Restless Leg Syndrome and Sleep Quality in Lumbar Radiculopathy Patients

PubMed Central

Terzi, Murat; Akpinar, Kursad; Paksoy, Kemal; Cebeci, Ibrahim; Iyigun, Omer

2014-01-01

Background. To investigate the frequency of restless leg syndrome (RLS), sleep quality impairment, depression, fatigue, and sleep behavior disorder and to determine the effects of surgery on these parameters in radiculopathy patients resistant to conservative treatment. Methods. The present study included 66 lumbar radiculopathy patients, who were resistant to conservative treatment and had indication of surgery. Five different questionnaires were performed to assess depression (the Beck Depression Inventory (BDI)), sleep quality (the Pittsburgh Sleep Quality Index (PSQI)), fatigue (the Fatigue Severity Scale (FSS)), and presence of RLS and rapid eye movement sleep behavior disorder (RBD). The same questionnaires were also performed on a control group (n = 61). Results. Of the radiculopathy patients, 68.1% had RLS and 92.4% had fatigue. Of the controls, 16.4% had RLS and 59% had fatigue. RBD was present in 8 (12.1%) patients and 3 (4.9%) controls. The PSQI revealed that sleep quality was impaired in 46 (69.7%) patients and 35 (57.4%) controls (P > 0.05). The number of individuals having substantial depression according to the BDI was significantly higher in the patients than in the controls. Conclusions. There was a significant increase in the frequency of RLS, which was significantly decreased in the postoperative period in the radiculopathy patients. PMID:25110396

[Quality evaluation of Artemisiae Argyi Folium based on fingerprint analysis and quantitative analysis of multicomponents].

PubMed

Guo, Long; Jiao, Qian; Zhang, Dan; Liu, Ai-Peng; Wang, Qian; Zheng, Yu-Guang

2018-03-01

Artemisiae Argyi Folium, the dried leaves of Artemisia argyi, has been widely used in traditional Chinese and folk medicines for treatment of hemorrhage, pain, and skin itch. Phytochemical studies indicated that volatile oil, organic acid and flavonoids were the main bioactive components in Artemisiae Argyi Folium. Compared to the volatile compounds, the research of nonvolatile compounds in Artemisiae Argyi Folium are limited. In the present study, an accurate and reliable fingerprint approach was developed using HPLC for quality control of Artemisiae Argyi Folium. A total of 10 common peaks were marked，and the similarity of all the Artemisiae Argyi Folium samples was above 0.940. The established fingerprint method could be used for quality control of Artemisiae Argyi Folium. Furthermore, an HPLC method was applied for simultaneous determination of seven bioactive compounds including five organic acids and two flavonoids in Artemisiae Argyi Folium and Artemisiae Lavandulaefoliae Folium samples. Moreover, chemometrics methods such as hierarchical clustering analysis and principal component analysis were performed to compare and discriminate the Artemisiae Argyi Folium and Artemisiae Lavandulaefoliae Folium based on the quantitative data of analytes. The results indicated that simultaneous quantification of multicomponents coupled with chemometrics analysis could be a well-acceptable strategy to identify and evaluate the quality of Artemisiae Argyi Folium. Copyright© by the Chinese Pharmaceutical Association.

Defect Analysis Of Quality Palm Kernel Meal Using Statistical Quality Control In Kernels Factory

NASA Astrophysics Data System (ADS)

Sembiring, M. T.; Marbun, N. J.

2018-04-01

The production quality has an important impact retain the totality of characteristics of a product or service to pay attention to its capabilities to meet the needs that have been established. Quality criteria Palm Kernel Meal (PKM) set Factory kernel is as follows: oil content: max 8.50%, water content: max 12,00% and impurity content: max 4.00% While the average quality of the oil content of 8.94%, the water content of 5.51%, and 8.45% impurity content. To identify the defective product quality PKM produced, then used a method of analysis using Statistical Quality Control (SQC). PKM Plant Quality Kernel shows the oil content was 0.44% excess of a predetermined maximum value, and 4.50% impurity content. With excessive PKM content of oil and dirt cause disability content of production for oil, amounted to 854.6078 kg PKM and 8643.193 kg impurity content of PKM. Analysis of the results of cause and effect diagram and SQC, the factors that lead to poor quality of PKM is Ampere second press oil expeller and hours second press oil expeller.

Effect of motivational interviewing on quality of life in patients with epilepsy.

PubMed

Hosseini, Nazafarin; Mokhtari, Somaye; Momeni, Ebrahim; Vossoughi, Mehrdad; Barekatian, Majid

2016-02-01

In this study, the effect of motivational interviewing on quality of life was evaluated in patients with epilepsy. Fifty-six patients with epilepsy in a clinical trial were randomly assigned to intervention and control groups. Motivational interviewing during 5 sessions was applied for the intervention group, and the control group received health-care services. Quality-of-life questionnaire in epilepsy (QOLIE-89) was applied as pre- and posttest for both groups. Before and two months after intervention, both groups were assessed. Data were analyzed by independent t-test, Chi-square test, and paired t-test. The data analysis showed that mean score of the QOLIE-89 was 38.94±8.55 and 70.90±7.99 in the intervention group before and after the intervention, respectfully, and 44.59±12.27 and 36.52±7.16 in the control group sequentially. The intervention group showed a significant score increase in their quality of life (p<0.001), whereas the control group had a score decrease (p<0.001). Motivational interviewing approach could be used as an effective intervention method for improving patients' quality of life. Copyright © 2015 Elsevier Inc. All rights reserved.

[Study of quality of a branch laboratory--an opinion of a laboratory manager].

PubMed

Yazawa, Naoyuki

2006-11-01

At the stage of establishing a branch laboratory, quality evaluation is extremely difficult. Even the results of a control survey by the headquarters of the branch laboratory are unhelpful. For a clinical laboratory, the most important function is to provide reliable data all the time, and to maintain the reliability of clinical doctors with informed responses. We mostly refer to control surveys and daily quality control data to evaluate a clinical laboratory, but we rarely check its fundamental abilities, such as planning events, preserving statistical data about the standard range, using the right method for quality control and others. This is generally disregarded and it is taken for granted that they will be correct the first time. From my six years of experience working with X's branch laboratory, I realized that there might be some relation between the quality of a branch laboratory and the fundamental abilities of the company itself. I would never argue that all branch laboratories are ineffective, but they should be conscious of fundamental activities. The referring laboratory, not the referral laboratory, should be responsible for ensuring that the referral laboratory's examination results and findings are correct.

Assessment of automatic exposure control performance in digital mammography using a no-reference anisotropic quality index

NASA Astrophysics Data System (ADS)

Barufaldi, Bruno; Borges, Lucas R.; Bakic, Predrag R.; Vieira, Marcelo A. C.; Schiabel, Homero; Maidment, Andrew D. A.

2017-03-01

Automatic exposure control (AEC) is used in mammography to obtain acceptable radiation dose and adequate image quality regardless of breast thickness and composition. Although there are physics methods for assessing the AEC, it is not clear whether mammography systems operate with optimal dose and image quality in clinical practice. In this work, we propose the use of a normalized anisotropic quality index (NAQI), validated in previous studies, to evaluate the quality of mammograms acquired using AEC. The authors used a clinical dataset that consists of 561 patients and 1,046 mammograms (craniocaudal breast views). The results show that image quality is often maintained, even at various radiation levels (mean NAQI = 0.14 +/- 0.02). However, a more careful analysis of NAQI reveals that the average image quality decreases as breast thickness increases. The NAQI is reduced by 32% on average, when the breast thickness increases from 31 to 71 mm. NAQI also decreases with lower breast density. The variation in breast parenchyma alone cannot fully account for the decrease of NAQI with thickness. Examination of images shows that images of large, fatty breasts are often inadequately processed. This work shows that NAQI can be applied in clinical mammograms to assess mammographic image quality, and highlights the limitations of the automatic exposure control for some images.

The Effect of Communication Skills Training on Quality of Care, Self-Efficacy, Job Satisfaction and Communication Skills Rate of Nurses in Hospitals of Tabriz, Iran

PubMed Central

Khodadadi, Esmail; Ebrahimi, Hossein; Moghaddasian, Sima; Babapour, Jalil

2013-01-01

Introduction: Having an effective relationship with the patient in the process of treatment is essential. Nurses must have communication skills in order to establish effective relationships with the patients. This study evaluated the impact of communication skills training on quality of care, self-efficacy, job satisfaction and communication skills of nurses. Methods: This is an experimental study with a control group that has been done in 2012. The study sample consisted of 73 nurses who work in hospitals of Tabriz; they were selected by proportional randomizing method. The intervention was only conducted on the experimental group. In order to measure the quality of care 160 patients, who had received care by nurses, participated in this study. The Data were analyzed by SPSS (ver.13). Results: Comparing the mean scores of communication skills showed a statistically significant difference between control and experimental groups after intervention. The paired t-test showed a statistically significant difference in the experimental group before and after the intervention. Independent t-test showed a statistically significant difference between the rate of quality of care in patients of control and experimental groups after the intervention. Conclusion: The results showed that the training of communication skills can increase the nurse's rate of communication skills and cause elevation in quality of nursing care. Therefore, in order to improve the quality of nursing care it is recommended that communication skills be established and taught as a separate course in nursing education. PMID:25276707

Lot quality assurance sampling of sputum acid-fast bacillus smears for assessing sputum smear microscopy centers.

PubMed

Selvakumar, N; Murthy, B N; Prabhakaran, E; Sivagamasundari, S; Vasanthan, Samuel; Perumal, M; Govindaraju, R; Chauhan, L S; Wares, Fraser; Santha, T; Narayanan, P R

2005-02-01

Assessment of 12 microscopy centers in a tuberculosis unit by blinded checking of eight sputum smears selected by using a lot quality assurance sampling (LQAS) method and by unblinded checking of all positive and five negative slides, among the slides examined in a month in a microscopy centre, revealed that the LQAS method can be implemented in the field to monitor the performance of acid-fast bacillus microscopy centers in national tuberculosis control programs.

Lot Quality Assurance Sampling of Sputum Acid-Fast Bacillus Smears for Assessing Sputum Smear Microscopy Centers

PubMed Central

Selvakumar, N.; Murthy, B. N.; Prabhakaran, E.; Sivagamasundari, S.; Vasanthan, Samuel; Perumal, M.; Govindaraju, R.; Chauhan, L. S.; Wares, Fraser; Santha, T.; Narayanan, P. R.

2005-01-01

Assessment of 12 microscopy centers in a tuberculosis unit by blinded checking of eight sputum smears selected by using a lot quality assurance sampling (LQAS) method and by unblinded checking of all positive and five negative slides, among the slides examined in a month in a microscopy centre, revealed that the LQAS method can be implemented in the field to monitor the performance of acid-fast bacillus microscopy centers in national tuberculosis control programs. PMID:15695704