40 CFR 97.732 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.632 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.732 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.632 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.732 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

Using magnetic levitation for non-destructive quality control of plastic parts.

PubMed

Hennek, Jonathan W; Nemiroski, Alex; Subramaniam, Anand Bala; Bwambok, David K; Yang, Dian; Harburg, Daniel V; Tricard, Simon; Ellerbee, Audrey K; Whitesides, George M

2015-03-04

Magnetic levitation (MagLev) enables rapid and non-destructive quality control of plastic parts. The feasibility of MagLev as a method to: i) rapidly assess injection-molded plastic parts for defects during process optimization, ii) monitor the degradation of plastics after exposure to harsh environmental conditions, and iii) detect counterfeit polymers by density is demonstrated. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Quality Assurance and Control Considerations in Environmental Measurements and Monitoring

NASA Astrophysics Data System (ADS)

Sedlet, Jacob

1982-06-01

Quality assurance and quality control have become accepted as essential parts of all environmental surveillance, measurements, and monitoring programs, both nuclear and non-nuclear. The same principles and details apply to each. It is primarily the final measurement technique that differs. As the desire and need to measure smaller amounts of pollutants with greater accuracy has increased, it has been recognized that quality assurance and control programs are cost-effective in achieving the expected results. Quality assurance (QA) consists of all the actions necessary to provide confidence in the results. Quality control (QC) is a part of QA, and consists of those actions and activities that permit the control of the individual steps in the environmental program. The distinction between the two terms is not always clearly defined, but a sharp division is not necessary. The essential principle of QA and QC is a commitment to high quality results. The essential components of a QA and QC program are a complete, written procedures manual for all parts of the environmental program, the use of standard or validated procedures, participation in applicable interlaboratory comparison or QA programs, replicate analysis and measurement, training of personnel, and a means of auditing or checking that the QA and QC programs are properly conducted. These components are discussed below in some detail.

40 CFR Appendix B to Part 425 - Modified Monier-Williams Method

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Modified Monier-Williams Method B... Appendix B to Part 425—Modified Monier-Williams Method Outline of Method Hydrogen sulfide is liberated from.... Quality Control 1. Each laboratory that uses this method is required to operate a formal quality control...

40 CFR Appendix B to Part 425 - Modified Monier-Williams Method

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Modified Monier-Williams Method B... Part 425—Modified Monier-Williams Method Outline of Method Hydrogen sulfide is liberated from an.... Quality Control 1. Each laboratory that uses this method is required to operate a formal quality control...

40 CFR Appendix B to Part 425 - Modified Monier-Williams Method

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Modified Monier-Williams Method B... Part 425—Modified Monier-Williams Method Outline of Method Hydrogen sulfide is liberated from an.... Quality Control 1. Each laboratory that uses this method is required to operate a formal quality control...

40 CFR 97.532 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or appendix E to, part 75 of this chapter...

40 CFR 97.532 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or appendix E to, part 75 of this chapter...

40 CFR 97.532 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or appendix E to, part 75 of this chapter...

32 CFR 507.1 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-07-01

... military decorations, medals, badges, and insignia. It also establishes the Heraldic Item Quality Control Program to improve the appearance of the Army and Air Force by controlling the quality of heraldic items... QUALITY CONTROL PROGRAM Introduction § 507.1 Purpose. This part prescribes the Department of the Army and...

Advanced Quality Control Theory for Training and Education: A Guide to Optimizing Training and Education Efforts

ERIC Educational Resources Information Center

Heppler, Brad

2008-01-01

This is a book about quality and how to control quality through deliberate actions on the part of the professionals developing and implementing the instances of instruction available at an organization. Quality control theory favors no particular learning philosophy and is only directed towards aspects of how, what, where and when measurements are…

Quality Assurance and Quality Control Practices for Rehabilitation of Sewer and Water Mains

EPA Science Inventory

As part of the US Environmental Protection Agency (EPA)’s Aging Water Infrastructure Research Program, several areas of research are being pursued, including a review of quality assurance and quality control (QA/QC) practices and acceptance testing during the installation of reha...

Quality Assurance and Quality Control Practices For Rehabilitation of Sewer and Water Mains

EPA Science Inventory

As part of the US Environmental Protection Agency (EPA)’s Aging Water Infrastructure Research Program, several areas of research are being pursued including a review of quality assurance and quality control (QA/QC) practices and acceptance testing during the installation of rehab...

Mechanical and Acoustic Characteristics of the Weld and the Base Metal Machine Part of Career Transport

NASA Astrophysics Data System (ADS)

Smirnov, Alexander N.; Knjaz'kov, Victor L.; Levashova, Elena E.; Ababkov, Nikolay V.; Pimonov, Maksim V.

2018-01-01

Currently, many industries use foreign-made machinery. There is no opportunity to purchase quality original spare parts for which machinery. Therefore, enterprises operating this equipment are looking for producers of analogues of various parts and assemblies. Quite often, the metal of such analog components turns out to be substandard, which leads to their breakdown at a much earlier date and the enterprises incur material losses. Due to the fact that the complex of performance characteristics and the resource of products are laid at the stage of their production, it is extremely important to control the quality of the raw materials. The structure, mechanical, acoustic and magnetic characteristics of metal samples of such destroyed details of quarry transport as hydraulic cylinders and detail “axis” of an excavator are investigated. A significant spread of data on the chemical composition of metal, hardness and characteristics of non-destructive testing is established, which gives grounds to recommend to manufacturers and suppliers of parts is more responsible to approach the incoming quality control. The results of the investigation of metal samples by destructive and non-destructive methods of control are compared, which showed that the spectral-acoustic method of nondestructive testing can be used to control the quality of the responsible machine parts under conditions of import substitution.

76 FR 75467 - Approval and Promulgation of Air Quality Implementation Plans; Louisiana; Revisions To Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-02

... Guidelines in Lieu of Regulations for Miscellaneous Metal Products Coatings, Plastic Parts Coatings, Auto and... Pleasure Craft portion of the Control Techniques Guidelines (CTG) for Miscellaneous Metal and Plastic Parts... and Plastic Parts Coatings regulations based on EPA's 2008 guidance titled ``Control Techniques...

[Essential guidelines for Quality Management System].

PubMed

Daunizeau, A

2013-06-01

The guidelines describe the essential parts of the quality management system to fulfil the requirements of the standard EN ISO 15 189. It includes mainly the organisation, the definition of responsibilities, training of personnel, the document control, the quality control, identification and control of nonconformities, corrective actions, preventive actions and evaluation, as audits and the management review.

40 CFR 60.2735 - Is there a minimum amount of monitoring data I must obtain?

Code of Federal Regulations, 2011 CFR

2011-07-01

....2770(o) of this part), and required monitoring system quality assurance or quality control activities... periods, and required monitoring system quality assurance or quality control activities including, as... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Is there a minimum amount of monitoring...

42 CFR 431.834 - Access to records: Claims processing assessment systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ADMINISTRATION Quality Control Medicaid Quality Control (mqc) Claims Processing Assessment System § 431.834... to which the State has access, including information available under part 435, subpart J, of this...

42 CFR 431.834 - Access to records: Claims processing assessment systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ADMINISTRATION Quality Control Medicaid Quality Control (mqc) Claims Processing Assessment System § 431.834... to which the State has access, including information available under part 435, subpart J, of this...

Quality assurance, an administrative means to a managerial end: Part I. A historical overview.

PubMed

Clark, G B

1990-01-01

Quality has become the hallmark of industrial excellence. Many diverse factors have heightened national concern about managing quality control throughout the health-care industry, including laboratory services. Industry-wide focus on quality control has created a need for an administrative program to evaluate its effectiveness. That program is medical quality assurance. Because of national and industry-wide concern, development of quality assurance theory has gained increasing importance in medical accreditation and management circles. Scrutiny of the application of quality assurance has become particularly prominent during accreditation inspections. Implementing quality assurance programs now demands more of already finite resources. The professional laboratory manager should understand how quality assurance has developed in the United States during the past 150 years. The well-informed manager should recognize why the health-care industry only recently began to develop its own expertise in quality assurance. It is also worthwhile to understand how heavily health care has relied on the lessons learned in the non-health-care sector. This three-part series will present information that will help in applying quality assurance more effectively as a management tool in the medical laboratory. This first part outlines the early industrial, socioeconomic, and medicolegal background of quality assurance. Terminology is defined with some distinction made between the terms management and administration. The second part will address current accreditation requirements. Special emphasis will be placed on the practical application of accreditation guidelines, providing a template for quality assurance methods in the medical laboratory. The third part will provide an overview of quality assurance as a total management tool with some suggestions for developing and implementing a quality assurance program.

78 FR 12267 - Revision of Air Quality Implementation Plan; California; Placer County Air Pollution Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-22

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R09-OAR-2013-0094; FRL-9783-2] Revision of Air Quality Implementation Plan; California; Placer County Air Pollution Control District and Feather River Air Quality Management District; Stationary Source Permits AGENCY: Environmental Protection Agency...

10 CFR 63.141 - Scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... its structures, systems, or components will perform satisfactorily in service. Quality assurance includes quality control, which comprises those quality assurance actions related to the physical..., NEVADA Quality Assurance § 63.141 Scope. As used in this part, quality assurance comprises all those...

Quality Control of Laser-Beam-Melted Parts by a Correlation Between Their Mechanical Properties and a Three-Dimensional Surface Analysis

NASA Astrophysics Data System (ADS)

Grimm, T.; Wiora, G.; Witt, G.

2017-03-01

Good correlations between three-dimensional surface analyses of laser-beam-melted parts of nickel alloy HX and their mechanical properties were found. The surface analyses were performed with a confocal microscope, which offers a more profound surface data basis than a conventional, two-dimensional tactile profilometry. This new approach results in a wide range of three-dimensional surface parameters, which were each evaluated with respect to their feasibility for quality control in additive manufacturing. As a result of an automated surface analysis process by the confocal microscope and an industrial six-axis robot, the results are an innovative approach for quality control in additive manufacturing.

40 CFR 147.1601 - State-administered program-Class I, III, IV and V wells.

Code of Federal Regulations, 2011 CFR

2011-07-01

... lands, is the program administered by the New Mexico Water Quality Control Commission, the Environmental..., are also part of the approved State-administered UIC program: (1) Water Quality Act, New Mexico...). (c)(1) The Memorandum of Agreement between EPA Region VI and the New Mexico Water Quality Control...

40 CFR 147.1601 - State-administered program-Class I, III, IV and V wells.

Code of Federal Regulations, 2010 CFR

2010-07-01

... lands, is the program administered by the New Mexico Water Quality Control Commission, the Environmental..., are also part of the approved State-administered UIC program: (1) Water Quality Act, New Mexico...). (c)(1) The Memorandum of Agreement between EPA Region VI and the New Mexico Water Quality Control...

Diagnosis of the Computer-Controlled Milling Machine, Definition of the Working Errors and Input Corrections on the Basis of Mathematical Model

NASA Astrophysics Data System (ADS)

Starikov, A. I.; Nekrasov, R. Yu; Teploukhov, O. J.; Soloviev, I. V.; Narikov, K. A.

2016-10-01

Manufactures, machinery and equipment improve of constructively as science advances and technology, and requirements are improving of quality and longevity. That is, the requirements for surface quality and precision manufacturing, oil and gas equipment parts are constantly increasing. Production of oil and gas engineering products on modern machine tools with computer numerical control - is a complex synthesis of technical and electrical equipment parts, as well as the processing procedure. Technical machine part wears during operation and in the electrical part are accumulated mathematical errors. Thus, the above-mentioned disadvantages of any of the following parts of metalworking equipment affect the manufacturing process of products in general, and as a result lead to the flaw.

42 CFR 480.109 - Applicability of other statutes and regulations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... AND HUMAN SERVICES (CONTINUED) QUALITY IMPROVEMENT ORGANIZATIONS ACQUISITION, PROTECTION, AND DISCLOSURE OF QUALITY IMPROVEMENT ORGANIZATION INFORMATION Utilization and Quality Control Quality... patients' records, and the implementing regulations at 42 CFR part 2, are applicable to QIO information...

42 CFR 480.109 - Applicability of other statutes and regulations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... AND HUMAN SERVICES (CONTINUED) QUALITY IMPROVEMENT ORGANIZATIONS ACQUISITION, PROTECTION, AND DISCLOSURE OF QUALITY IMPROVEMENT ORGANIZATION INFORMATION Utilization and Quality Control Quality... patients' records, and the implementing regulations at 42 CFR part 2, are applicable to QIO information...

42 CFR 480.109 - Applicability of other statutes and regulations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... AND HUMAN SERVICES (CONTINUED) QUALITY IMPROVEMENT ORGANIZATIONS ACQUISITION, PROTECTION, AND DISCLOSURE OF QUALITY IMPROVEMENT ORGANIZATION INFORMATION Utilization and Quality Control Quality... patients' records, and the implementing regulations at 42 CFR part 2, are applicable to QIO information...

10 CFR 60.150 - Scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... components will perform satisfactorily in service. Quality assurance includes quality control, which... COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Quality Assurance § 60.150 Scope. As used in this part, quality assurance comprises all those planned and systematic...

78 FR 28773 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-16

... Miscellaneous Metal and Plastic Parts Which Includes Pleasure Craft Coating Operations AGENCY: Environmental... recommended by EPA's control technique guidelines (CTG) for Miscellaneous Metal Parts and Plastic Coating... air pollution control authorities information that should assist them in determining RACT for VOC from...

Quality control analysis : part II : soil and aggregate base course.

DOT National Transportation Integrated Search

1966-07-01

This is the second of the three reports on the quality control analysis of highway construction materials. : It deals with the statistical evaluation of results from several construction projects to determine the basic pattern of variability with res...

Quality control analysis : part III : concrete and concrete aggregates.

DOT National Transportation Integrated Search

1966-11-01

This is the third and last report on the Quality Control Analysis of highway construction materials. : It deals with the statistical evaluation of data from several construction projects to determine the basic pattern of variability with respect to s...

Quality management in in vivo proton MRS.

PubMed

Pedrosa de Barros, Nuno; Slotboom, Johannes

2017-07-15

The quality of MR-Spectroscopy data can easily be affected in in vivo applications. Several factors may produce signal artefacts, and often these are not easily detected, not even by experienced spectroscopists. Reliable and reproducible in vivo MRS-data requires the definition of quality requirements and goals, implementation of measures to guarantee quality standards, regular control of data quality, and a continuous search for quality improvement. The first part of this review includes a general introduction to different aspects of quality management in MRS. It is followed by the description of a series of tests and phantoms that can be used to assure the quality of the MR system. In the third part, several methods and strategies used for quality control of the spectroscopy data are presented. This review concludes with a reference to a few interesting techniques and aspects that may help to further improve the quality of in vivo MR-spectra. Copyright © 2017 Elsevier Inc. All rights reserved.

Medical Devices; Immunology and Microbiology Devices; Classification of the Assayed Quality Control Material for Clinical Microbiology Assays. Final order.

PubMed

2017-07-27

The Food and Drug Administration (FDA, Agency, or we) is classifying the assayed quality control material for clinical microbiology assays into class II (special controls). The special controls that will apply to the device are identified in this order and will be part of the codified language for the assayed quality control material for clinical microbiology assays' classification. The Agency is classifying the device into class II (special controls) to provide a reasonable assurance of safety and effectiveness of the device.

77 FR 45307 - Approval and Promulgation of Air Quality Implementation Plans: Georgia; Control Techniques...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-31

... October 7, 2008 (73 FR 58481), EPA updated the 1977 CTG, as part of Group IV CTG, addressing the control... Group III CTG, addressing control of VOC emissions from metal furniture coating operations. On January 3..., as part of Group III CTG, addressing the control of VOC emissions from large appliance surface...

42 CFR 480.109 - Applicability of other statutes and regulations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... AND HUMAN SERVICES (CONTINUED) QUALITY IMPROVEMENT ORGANIZATIONS ACQUISITION, PROTECTION, AND DISCLOSURE OF QUALITY IMPROVEMENT ORGANIZATION REVIEW INFORMATION Utilization and Quality Control Quality... patients' records, and the implementing regulations at 42 CFR part 2, are applicable to QIO information...

Effects of side-stick controllers on rotorcraft handling qualities for terrain flight

NASA Technical Reports Server (NTRS)

Aiken, E. W.

1985-01-01

Pertinent fixed and rotary-wing feasibility studies and handling-qualities research programs are reviewed and the effects of certain controller characteristics on handling qualities for specific rotorcraft flight tasks are summarized. The effects of the controller force-deflection relationship and the number of controlled axes that are integrated in a single controller are examined. Simulation studies were conducted which provide a significant part of the available handling qualities data. The studies demonstrate the feasibility of using a single, properly designed, limited-displacement, multiaxis controller for certain relatively routine flight tasks in a two-crew rotorcraft with nominal levels of stability and control augmentation with a high degree of reliability are incorporated, separated three or two-axis controller configurations are required for acceptable handling qualities.

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.372 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... the Administrator revokes prospectively the certification status of the monitoring system. The data...

40 CFR 96.372 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... the Administrator revokes prospectively the certification status of the monitoring system. The data...

40 CFR 96.372 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... the Administrator revokes prospectively the certification status of the monitoring system. The data...

40 CFR 96.372 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... the Administrator revokes prospectively the certification status of the monitoring system. The data...

40 CFR 96.372 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... the Administrator revokes prospectively the certification status of the monitoring system. The data...

21 CFR 107.50 - Terms and conditions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Center for Food Safety and Applied Nutrition concludes that additional or modified quality control... also typically represented and labeled for use to provide dietary management for diseases or conditions... regulations promulgated under section 412(a)(2) of the act, the quality control procedure requirements of part...

Alignment issues, correlation techniques and their assessment for a visible light imaging-based 3D printer quality control system

NASA Astrophysics Data System (ADS)

Straub, Jeremy

2016-05-01

Quality control is critical to manufacturing. Frequently, techniques are used to define object conformity bounds, based on historical quality data. This paper considers techniques for bespoke and small batch jobs that are not statistical model based. These techniques also serve jobs where 100% validation is needed due to the mission or safety critical nature of particular parts. One issue with this type of system is alignment discrepancies between the generated model and the physical part. This paper discusses and evaluates techniques for characterizing and correcting alignment issues between the projected and perceived data sets to prevent errors attributable to misalignment.

Quality assurance: Importance of systems and standard operating procedures

PubMed Central

Manghani, Kishu

2011-01-01

It is mandatory for sponsors of clinical trials and contract research organizations alike to establish, manage and monitor their quality control and quality assurance systems and their integral standard operating procedures and other quality documents to provide high-quality products and services to fully satisfy customer needs and expectations. Quality control and quality assurance systems together constitute the key quality systems. Quality control and quality assurance are parts of quality management. Quality control is focused on fulfilling quality requirements, whereas quality assurance is focused on providing confidence that quality requirements are fulfilled. The quality systems must be commensurate with the Company business objectives and business model. Top management commitment and its active involvement are critical in order to ensure at all times the adequacy, suitability, effectiveness and efficiency of the quality systems. Effective and efficient quality systems can promote timely registration of drugs by eliminating waste and the need for rework with overall financial and social benefits to the Company. PMID:21584180

Quality assurance: Importance of systems and standard operating procedures.

PubMed

Manghani, Kishu

2011-01-01

It is mandatory for sponsors of clinical trials and contract research organizations alike to establish, manage and monitor their quality control and quality assurance systems and their integral standard operating procedures and other quality documents to provide high-quality products and services to fully satisfy customer needs and expectations. Quality control and quality assurance systems together constitute the key quality systems. Quality control and quality assurance are parts of quality management. Quality control is focused on fulfilling quality requirements, whereas quality assurance is focused on providing confidence that quality requirements are fulfilled. The quality systems must be commensurate with the Company business objectives and business model. Top management commitment and its active involvement are critical in order to ensure at all times the adequacy, suitability, effectiveness and efficiency of the quality systems. Effective and efficient quality systems can promote timely registration of drugs by eliminating waste and the need for rework with overall financial and social benefits to the Company.

Stellarator Saddle Coils

NASA Astrophysics Data System (ADS)

Boozer, Allen H.

1999-11-01

Modern stellarators are designed using J. Nuehrenberg’s method of varying Fourier coefficients in the shape of the plasma boundary to maximize a target function. The matrix of second derivatives of the target function at the optimum determines a quality matrix. This matrix gives the degradation in the quality of the configuration as the normal magnetic field is varied on a control surface, which lies on or outside the plasma surface. The task is finding saddle coils that produce the desired configuration in the presence of a given toroidal field. An eigenvector of the quality matrix can be important for two reasons: (1) the normal field that must be produced by the saddles is large or (2) the eigenvalue is large (an island-causing resonant perturbation). The rank of the important part of the quality matrix is the number of important eigenvectors. The current in each saddle coil produces a normal field on the control surface, which can be described by an inductance matrix. The relevant part of the inductance matrix has large eigenvalues. The coils can produce the configuration if the rank of the important part of the quality matrix and its product with the relevant part of the inductance matrix are the same. Existing coil design codes, pioneered by P. Merkel, approximate the quality matrix by the unit matrix. Stellarator flexibility could be enhanced by using a more realistic quality matrix and by using trim coils to balance large eigenvalues.

75 FR 18142 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Control of Air Pollution...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-09

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R06-OAR-2006-0988; FRL-9135-5] Approval and Promulgation of Air Quality Implementation Plans; Texas; Control of Air Pollution From Motor Vehicles AGENCY... (TAC), Chapter 114, Control of Air Pollution from Motor Vehicles. The State submitted these revisions...

Parameter Trending, Geolocation Quality Control and the Procedures to Support Preparation of Next Versions of the TRMM Reprocessing Algorithm

NASA Technical Reports Server (NTRS)

Stocker, Erich Franz

2004-01-01

TRMM has been an imminently successful mission from an engineering standpoint but even more from a science standpoint. An important part of this science success has been the careful quality control of the TRMM standard products. This paper will present the quality monitoring efforts that the TRMM Science Data and Information System (TSDIS) conducts on a routine basis. The paper will detail parameter trending, geolocation quality control and the procedures to support the preparation of next versions of the algorithm used for reprocessing.

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 35.400 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Pollution Control), 205(j)(2) (Water Quality Management Planning), and 104(b)(3) (Water Quality Cooperative... quality management activities are provided in 40 CFR part 130. ... program. EPA awards these grants for the following two purposes: (1) Construction management grants. A...

Quality assessment concept of the World Data Center for Climate and its application to CMIP5 data

NASA Astrophysics Data System (ADS)

Stockhause, M.; Höck, H.; Toussaint, F.; Lautenschlager, M.

2012-08-01

The preservation of data in a high state of quality which is suitable for interdisciplinary use is one of the most pressing and challenging current issues in long-term archiving. For high volume data such as climate model data, the data and data replica are no longer stored centrally but distributed over several local data repositories, e.g. the data of the Climate Model Intercomparison Project Phase 5 (CMIP5). The most important part of the data is to be archived, assigned a DOI, and published according to the World Data Center for Climate's (WDCC) application of the DataCite regulations. The integrated part of WDCC's data publication process, the data quality assessment, was adapted to the requirements of a federated data infrastructure. A concept of a distributed and federated quality assessment procedure was developed, in which the workload and responsibility for quality control is shared between the three primary CMIP5 data centers: Program for Climate Model Diagnosis and Intercomparison (PCMDI), British Atmospheric Data Centre (BADC), and WDCC. This distributed quality control concept, its pilot implementation for CMIP5, and first experiences are presented. The distributed quality control approach is capable of identifying data inconsistencies and to make quality results immediately available for data creators, data users and data infrastructure managers. Continuous publication of new data versions and slow data replication prevents the quality control from check completion. This together with ongoing developments of the data and metadata infrastructure requires adaptations in code and concept of the distributed quality control approach.

14 CFR 21.143 - Quality control data requirements; prime manufacturer.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., purchased items, and parts and assemblies produced by manufacturers' suppliers including methods used to... special manufacturing processes involved, the means used to control the processes, the final test... procedure for recording review board decisions and disposing of rejected parts; (5) An outline of a system...

40 CFR 97.432 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.432 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 60.4172 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... certification status of the monitoring system. The data measured and recorded by the monitoring system shall not...

40 CFR 97.432 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 60.4172 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... certification status of the monitoring system. The data measured and recorded by the monitoring system shall not...

76 FR 33188 - Quality Assurance Requirements for Respirators; Notice of Withdrawal

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-08

... Quality Assurance Requirements for Respirators; Notice of Withdrawal AGENCY: Centers for Disease Control... approved under 42 CFR Part 84 by the National Institute for Occupational Safety and Health (NIOSH), Centers for Disease Control and Prevention and the Mine Safety and Health Administration (MSHA). NIOSH has...

14 CFR 21.303 - Replacement and modification parts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... determination can be made. Statistical quality control procedures may be employed where it is shown that a... AIRCRAFT CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS Approval of Materials, Parts, Processes, and... the configuration of the part; and (ii) Information on dimensions, materials, and processes necessary...

Curing of Furfuryl Alcohol-Impregnated Parts

NASA Technical Reports Server (NTRS)

Lawton, J. W.; Brayden, T. H.

1983-01-01

Delamination problem in reinforced carbon/carbon parts impregnated with oxalic acid-catalyzed furfuryl alcohol overcome by instituting two additional quality-control tests on alcohol and by changing curing conditions.

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

Analytic Methods Used in Quality Control in a Compounding Pharmacy.

PubMed

Allen, Loyd V

2017-01-01

Analytical testing will no doubt become a more important part of pharmaceutical compounding as the public and regulatory agencies demand increasing documentation of the quality of compounded preparations. Compounding pharmacists must decide what types of testing and what amount of testing to include in their quality-control programs, and whether testing should be done in-house or outsourced. Like pharmaceutical compounding, analytical testing should be performed only by those who are appropriately trained and qualified. This article discusses the analytical methods that are used in quality control in a compounding pharmacy. Copyright© by International Journal of Pharmaceutical Compounding, Inc.

Parts Quality Management: Direct Part Marking via Data Matrix Symbols for Mission Assurance

NASA Technical Reports Server (NTRS)

Moss, Chantrice

2013-01-01

A United States Government Accountability Office (GAO) review of twelve NASA programs found widespread parts quality problems contributing to significant cost overruns, schedule delays, and reduced system reliability. Direct part-marking with Data Matrix symbols could significantly improve the quality of inventory control and parts lifecycle management. This paper examines the feasibility of using 15 marking technologies for use in future NASA programs. A structural analysis is based on marked material type, operational environment (e.g., ground, suborbital, orbital), durability of marks, ease of operation, reliability, and affordability. A cost-benefits analysis considers marking technology (data plates, label printing, direct part marking) and marking types (two-dimensional machine-readable, human-readable). Previous NASA parts marking efforts and historical cost data are accounted for, including in-house vs. outsourced marking. Some marking methods are still under development. While this paper focuses on NASA programs, results may be applicable to a variety of industrial environments.

Quality Assurance in UK Higher Education: Issues of Trust, Control, Professional Autonomy and Accountability

ERIC Educational Resources Information Center

Hoecht, Andreas

2006-01-01

This article explores the issues of trust, control, professional autonomy and accountability in higher education quality assurance in the UK. The main part of this article is conceptual, but it includes results from semi-structured interviews with academic staff that were conducted at two "new university" business schools. Both…

77 FR 16676 - Approval and Promulgation of Implementation Plans and Operating Permits Program; Commonwealth of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-22

... Pollution, submitted to EPA by the Puerto Rico Environmental Quality Board on July 13, 2011. This action...)(2).) List of Subjects 40 CFR Part 52 Environmental protection, Air pollution control, Incorporation... Control of Atmospheric Pollution submitted on July 13, 2011 by the Puerto Rico Environmental Quality Board...

76 FR 59089 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-23

... in 40 CFR Part 52 Environmental protection, Air pollution control, Ozone, Reporting and recordkeeping... Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the Control of Volatile Organic... action is being taken under the Clean Air Act (CAA). DATES: Written comments must be received on or...

Using quality control to limit bismuth in copper cathodes

NASA Astrophysics Data System (ADS)

Serrano, John R.; Berger, Dennis; Bridges, Bill

1994-10-01

This article describes quality-control work at Phelps Dodge, undertaken as part of ISO 9003 certification, to better identify and prevent the contamination of copper cathodes by bismuth. It also overviews the implementation of a production control system as well as associated training designed to minimize the possibility of bismuth-contaminated copper progressing beyond the cathode stage to other areas of manufacturing or distribution.

"A manager in the minds of doctors:" a comparison of new modes of control in European hospitals.

PubMed

Kuhlmann, Ellen; Burau, Viola; Correia, Tiago; Lewandowski, Roman; Lionis, Christos; Noordegraaf, Mirko; Repullo, Jose

2013-07-02

Hospital governance increasingly combines management and professional self-governance. This article maps the new emergent modes of control in a comparative perspective and aims to better understand the relationship between medicine and management as hybrid and context-dependent. Theoretically, we critically review approaches into the managerialism-professionalism relationship; methodologically, we expand cross-country comparison towards the meso-level of organisations; and empirically, the focus is on processes and actors in a range of European hospitals. The research is explorative and was carried out as part of the FP7 COST action IS0903 Medicine and Management, Working Group 2. Comprising seven European countries, the focus is on doctors and public hospitals. We use a comparative case study design that primarily draws on expert information and document analysis as well as other secondary sources. The findings reveal that managerial control is not simply an external force but increasingly integrated in medical professionalism. These processes of change are relevant in all countries but shaped by organisational settings, and therefore create different patterns of control: (1) 'integrated' control with high levels of coordination and coherent patterns for cost and quality controls; (2) 'partly integrated' control with diversity of coordination on hospital and department level and between cost and quality controls; and (3) 'fragmented' control with limited coordination and gaps between quality control more strongly dominated by medicine, and cost control by management. Our comparison highlights how organisations matter and brings the crucial relevance of 'coordination' of medicine and management across the levels (hospital/department) and the substance (cost/quality-safety) of control into perspective. Consequently, coordination may serve as a taxonomy of emergent modes of control, thus bringing new directions for cost-efficient and quality-effective hospital governance into perspective.

Optimization of the central automatic control of a small Dutch sewer system

NASA Astrophysics Data System (ADS)

Kolechkina, A. G.; Hoes, O. A. C.

2012-04-01

A sewer control system was developed in the context of a subsidized project aiming at improvement of surface water quality by control of sewer systems and surface water systems. The project was coordinated by the local water board, "Waterschap Hollandse Delta". Other participants were Delft University of Technology, Deltares and the municipalities Strijen, Cromstrijen, Westmaas, Oud Beijerland and Piershil. As part of the project there were two pilot implementations where a central automatic controller was coupled to the existing SCADA system. For these two pilots the system is now operational. A Dutch urban area in the western part of the Netherlands is usually part of a polder, which is effectively an artificially drained catchment. The urban area itself is split into small subcatchments that manage runoff in different ways. In all cases a large fraction goes into the natural hydrological cycle, but, depending on the design of the local sewer system, a larger or smaller part finds its way into the sewer system. Proper control of this flow is necessary to control surface water quality and to avoid health risks from flow from the sewer into the streets. At each time step the controller switches pumps to distribute the remaining water in the system at the end of the time step over the different subcatchments. The distribution is created based on expert judgment of the relative vulnerability and subcatchment sewer system water quality. It is implemented in terms curves of total system stored volume versus subcatchment stored volume. We describe the process of the adaptation of a controller to two different sewer systems and the understanding of the artificial part of the catchment we gained during this process. In the process of adaptation the type of sewer system (combined foul water and storm water transport or separate foul water and storm water transport) played a major role.

Software quality assurance plan for GCS

NASA Technical Reports Server (NTRS)

Duncan, Stephen E.; Bailey, Elizabeth K.

1990-01-01

The software quality assurance (SQA) function for the Guidance and Control Software (GCS) project which is part of a software error studies research program is described. The SQA plan outlines all of the procedures, controls, and audits to be carried out by the SQA organization to ensure adherence to the policies, procedures, and standards for the GCS project.

76 FR 40246 - Approval and Promulgation of Air Quality Implementation Plans; Ohio; Control of Gasoline...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R05-OAR-2006-0976; FRL-9430-5] Approval and Promulgation of Air Quality Implementation Plans; Ohio; Control of Gasoline Volatility; Correction AGENCY... a gasoline Reid Vapor Pressure (RVP) limit of 7.8 pounds per square inch (psi) for gasoline sold in...

10 CFR Appendix I to Part 110 - Illustrative List of Reprocessing Plant Components Under NRC Export Licensing Authority

Code of Federal Regulations, 2011 CFR

2011-01-01

... assurance and quality control techniques) out of low carbon stainless steels, titanium, zirconium or other... materials such as low carbon stainless steels, titanium or zirconium, or other high quality materials... features for control of nuclear criticality: (i) Walls or internal structures with a boron equivalent of at...

Parts quality management: Direct part marking of data matrix symbol for mission assurance

NASA Astrophysics Data System (ADS)

Moss, Chantrice; Chakrabarti, Suman; Scott, David W.

A United States Government Accountability Office (GAO) review of twelve NASA programs found widespread parts quality problems contributing to significant cost overruns, schedule delays, and reduced system reliability. Direct part marking with Data Matrix symbols could significantly improve the quality of inventory control and parts lifecycle management. This paper examines the feasibility of using direct part marking technologies for use in future NASA programs. A structural analysis is based on marked material type, operational environment (e.g., ground, suborbital, Low Earth Orbit), durability of marks, ease of operation, reliability, and affordability. A cost-benefits analysis considers marking technology (label printing, data plates, and direct part marking) and marking types (two-dimensional machine-readable, human-readable). Previous NASA parts marking efforts and historical cost data are accounted for, including in-house vs. outsourced marking. Some marking methods are still under development. While this paper focuses on NASA programs, results may be applicable to a variety of industrial environments.

Parts Quality Management: Direct Part Marking of Data Matrix Symbol for Mission Assurance

NASA Technical Reports Server (NTRS)

Moss, Chantrice; Chakrabarti, Suman; Scott, David W.

2013-01-01

A United States Government Accountability Office (GAO) review of twelve NASA programs found widespread parts quality problems contributing to significant cost overruns, schedule delays, and reduced system reliability. Direct part marking with Data Matrix symbols could significantly improve the quality of inventory control and parts lifecycle management. This paper examines the feasibility of using direct part marking technologies for use in future NASA programs. A structural analysis is based on marked material type, operational environment (e.g., ground, suborbital, Low Earth Orbit), durability of marks, ease of operation, reliability, and affordability. A cost-benefits analysis considers marking technology (label printing, data plates, and direct part marking) and marking types (two-dimensional machine-readable, human-readable). Previous NASA parts marking efforts and historical cost data are accounted for, including inhouse vs. outsourced marking. Some marking methods are still under development. While this paper focuses on NASA programs, results may be applicable to a variety of industrial environments.

CHALLENGES IN SETTING UP QUALITY CONTROL IN DIAGNOSTIC RADIOLOGY FACILITIES IN NIGERIA.

PubMed

Inyang, S O; Egbe, N O; Ekpo, E

2015-01-01

The Nigerian Nuclear Regulatory Authority (NNRA) was established to regulate and control the use of radioactive and radiation emitting sources in Nigeria. Quality control (QC) on diagnostic radiology equipment form part of the fundamental requirements for the authorization of diagnostic radiology facilities in the Country. Some quality control tests (output, exposure linearity and reproducibility) were measured on the x-ray machines in the facilities that took part in the study. Questionnaire was developed to evaluate the frequencies at which QC tests were conducted in the facilities and the challenges in setting up QC. Results show great variation in the values of the QC parameters measured. Inadequate cooperation by facilities management, lack of QC equipment and insufficient staff form the major challenges in setting up QC in the facilities under study. The responses on the frequencies at which QC tests should be conducted did not correspond to the recommended standards; indicating that personnel were not familiar with QC implementation and may require further training on QC.

[HPLC-fingerprint-based quality evaluation on a Tibetan medicine Phyllanthus emblica and its tannin parts].

PubMed

Sun, Xue-Fei; Zhang, Hong-Yan; Xia, Qing; Zhao, Hai-Juan; Wu, Ling-Fang; Zhang, Lan-Zhen; Shi, Ren-Bing

2014-04-01

This study is to establish the fingerprint for Phyllanthus emblica and their tannin parts from different habitats by HPLC for its quality control. The determination was carried out on a Diamonsil C18 (4.6 mm x 250 mm, 5 microm) column, with methanol-0.2% glacial acetic acid as mobile phase with gradient elution at a flow rate of 1 mL x min(-1). The temperature was maintained at 30 degrees C and the detected wavelength is 260 nm, Thirteen chromatographic peaks were extracted as the common peaks of the fingerprint of P. emblica, and eleven as the common peaks of P. emblica tannin parts, and five peaks were identified by comparing with referent samples. The fingerprints of 8 samples were compared and classified by similarity evaluation, cluster analysis and principal component analysis (PCA). The similarity degrees of eight P. emblica were between 0.763 and 0.993, while tannin parts were between 0.903 and 0.991. All the samples of P. emblica and their tannin parts were classified into 3 categories. The method was so highly reproducible, simple and reliable that it could provide basis for quality control and evaluation of P. emblica from different habitats.

78 FR 59240 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-26

... Guidelines for Miscellaneous Metal and Plastic Parts Which Includes Pleasure Craft Coating Operations AGENCY... Miscellaneous Metal Parts and Plastic Coating (MMPPC) operations and as recommended by trade associations...

Data-quality measures for stakeholder-implemented watershed-monitoring programs

USGS Publications Warehouse

Greve, Adrienne I.

2002-01-01

Community-based watershed groups, many of which collect environmental data, have steadily increased in number over the last decade. The data generated by these programs are often underutilized due to uncertainty in the quality of data produced. The incorporation of data-quality measures into stakeholder monitoring programs lends statistical validity to data. Data-quality measures are divided into three steps: quality assurance, quality control, and quality assessment. The quality-assurance step attempts to control sources of error that cannot be directly quantified. This step is part of the design phase of a monitoring program and includes clearly defined, quantifiable objectives, sampling sites that meet the objectives, standardized protocols for sample collection, and standardized laboratory methods. Quality control (QC) is the collection of samples to assess the magnitude of error in a data set due to sampling, processing, transport, and analysis. In order to design a QC sampling program, a series of issues needs to be considered: (1) potential sources of error, (2) the type of QC samples, (3) inference space, (4) the number of QC samples, and (5) the distribution of the QC samples. Quality assessment is the process of evaluating quality-assurance measures and analyzing the QC data in order to interpret the environmental data. Quality assessment has two parts: one that is conducted on an ongoing basis as the monitoring program is running, and one that is conducted during the analysis of environmental data. The discussion of the data-quality measures is followed by an example of their application to a monitoring program in the Big Thompson River watershed of northern Colorado.

An Application of Quality Control Theory to Vendor-Supplied Parts at an Aerospace Manufacturing Company.

DTIC Science & Technology

1985-08-01

presently used on the ATF3-6, TFE731 -2, -3, TPE331, GTCP660 and TSCP700 engines. Substantiation Metallurgical V Testing Tnstructions Control Part Name Part... TFE731 -2, -3 Fan 3072162 Ti-6-4 5001 C1.-2 L’$S52458 1st Stg.Comp. 3072193 Ti-6-4 5001 C1.-l AF5395 2nd Stg.Comp. 3072191 Ti-6-4 5001 CI.-I AF5395 W...Control Part Nam~e Part No. material (STIT~eouirernents Specification TFE731 -2, -3 4th Stg.Conp. 3072.93 Ti-6-4 5001 C1.-1 AF5395 HP Comp. 3072639 Ti-6-2

Warpage optimisation on the moulded part with straight-drilled and conformal cooling channels using response surface methodology (RSM) and glowworm swarm optimisation (GSO)

NASA Astrophysics Data System (ADS)

Hazwan, M. H. M.; Shayfull, Z.; Sharif, S.; Nasir, S. M.; Zainal, N.

2017-09-01

In injection moulding process, quality and productivity are notably important and must be controlled for each product type produced. Quality is measured as the extent of warpage of moulded parts while productivity is measured as a duration of moulding cycle time. To control the quality, many researchers have introduced various of optimisation approaches which have been proven enhanced the quality of the moulded part produced. In order to improve the productivity of injection moulding process, some of researches have proposed the application of conformal cooling channels which have been proven reduced the duration of moulding cycle time. Therefore, this paper presents an application of alternative optimisation approach which is Response Surface Methodology (RSM) with Glowworm Swarm Optimisation (GSO) on the moulded part with straight-drilled and conformal cooling channels mould. This study examined the warpage condition of the moulded parts before and after optimisation work applied for both cooling channels. A front panel housing have been selected as a specimen and the performance of proposed optimisation approach have been analysed on the conventional straight-drilled cooling channels compared to the Milled Groove Square Shape (MGSS) conformal cooling channels by simulation analysis using Autodesk Moldflow Insight (AMI) 2013. Based on the results, melt temperature is the most significant factor contribute to the warpage condition and warpage have optimised by 39.1% after optimisation for straight-drilled cooling channels and cooling time is the most significant factor contribute to the warpage condition and warpage have optimised by 38.7% after optimisation for MGSS conformal cooling channels. In addition, the finding shows that the application of optimisation work on the conformal cooling channels offers the better quality and productivity of the moulded part produced.

[Comparative quality measurements part 3: funnel plots].

PubMed

Kottner, Jan; Lahmann, Nils

2014-02-01

Comparative quality measurements between organisations or institutions are common. Quality measures need to be standardised and risk adjusted. Random error must also be taken adequately into account. Rankings without consideration of the precision lead to flawed interpretations and enhances "gaming". Application of confidence intervals is one possibility to take chance variation into account. Funnel plots are modified control charts based on Statistical Process Control (SPC) theory. The quality measures are plotted against their sample size. Warning and control limits that are 2 or 3 standard deviations from the center line are added. With increasing group size the precision increases and so the control limits are forming a funnel. Data points within the control limits are considered to show common cause variation; data points outside special cause variation without the focus of spurious rankings. Funnel plots offer data based information about how to evaluate institutional performance within quality management contexts.

46 CFR 160.135-15 - Production inspections, tests, quality control, and conformance of lifeboats.

Code of Federal Regulations, 2014 CFR

2014-10-01

... materials are as per the plans approved under § 160.135-13(h) of this subpart. (2) Post assembly tests and... each design must pass each of the tests described in the IMO Revised recommendation on testing, part 2... 46 Shipping 6 2014-10-01 2014-10-01 false Production inspections, tests, quality control, and...

Relations of Children's Effortful Control and Teacher-Child Relationship Quality to School Attitudes in a Low-Income Sample

ERIC Educational Resources Information Center

Silva, Kassondra M.; Spinrad, Tracy L.; Eisenberg, Nancy; Sulik, Michael J.; Valiente, Carlos; Huerta, Snjezana; Edwards, Alison; Eggum, Natalie D.; Kupfer, Anne S.; Lonigan, Christopher J.; Phillips, Beth M.; Wilson, Shauna B.; Clancy-Menchetti, Jeanine; Landry, Susan H.; Swank, Paul R.; Assel, Michael A.; Taylor, Heather B.

2011-01-01

Research Findings: The purpose of this study was to examine the relations of children's effortful control and quality of relationships with teachers to school attitudes longitudinally in an ethnically diverse and economically disadvantaged sample. Data were collected as part of a larger intervention project during mid-fall, winter, and late spring…

40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

Code of Federal Regulations, 2014 CFR

2014-07-01

... transmitters of an orifice-, nozzle-, or venturi-type fuel flowmeter under section 2.1.6 of appendix D to this... nozzle) of an orifice-, venturi-, or nozzle-type fuel flowmeter. Examples of the types of information to..., but ≤200 ppm). The out-of-control period begins upon failure of the calibration error test and ends...

The effect of psycho-educational intervention on the life quality of major depressive patients referred to hospitals affiliated to Shiraz University of Medical Sciences in Shiraz-Iran.

PubMed

Sharif, Farkhondeh; Nourian, Kheirollah; Ashkani, Hamid; Zoladl, Mohamad

2012-09-01

Depression is the world's fourth most prevalent health problem which is associated with substantial mortality, direct medical cost, diminished life quality, and significant physical and psychosocial impairment. This study aimed to investigate the effect of psycho-educational intervention on the life quality of major depressive patients. Sixty patients who were willing and had met the required criteria for participation were selected from hospitals in Shiraz city, Iran. So 30 of the patients were assigned to the experimental group and 30 others to the control group. For data collection, a two part questionnaire was developed, the first part consists of 13 items related to general characteristics and the second part with 36 items on life quality were used. The experimental group was divided into five subgroups of 6 patients. For each group, six intervention sessions were scheduled. The control group did not receive the intervention. The questionnaires were completed for all subjects in the experimental and control groups before and 1 month after the end of psycho-educational intervention. Tabulated data were analyzed using chi-square, independent and pair T-test. The results of the study indicated that psycho-educational intervention in comparison with other available treatments proved to be more effective on eight domains of life quality in the experimental group. A significant difference was observed for all the domains (P < 0.001). Psycho-educational intervention can be used as an auxiliary treatment in improving life quality and decreasing depression in patients suffering from major depressive disorder.

75 FR 32658 - Change of Contact Information; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-09

... nonsubstantive content. List of Subjects 21 CFR Part 106 Food grades and standards, Infants and children, Nutrition, Reporting and recordkeeping requirements. 21 CFR Part 107 Food labeling, Infants and children..., 21 CFR Chapter I is amended as follows: PART 106--INFANT FORMULA QUALITY CONTROL PROCEDURES 0 1. The...

76 FR 64020 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-17

... Plastic Parts and Business Machines Coatings AGENCY: Environmental Protection Agency (EPA). ACTION: Final....19.07-2, Plastic Parts and Business Machines Coating. Maryland's SIP revision meets the requirement... Techniques Guidelines (CTG) standards for plastic parts and business machines coatings and will help Maryland...

Setting and Reviewing Standards to Control Ozone Pollution

EPA Pesticide Factsheets

Ozone standards are part of the National Ambient Air Quality Standards (NAAQS), which limit air pollution to protect health and the environment. Standards are periodically reviewed and updated, and air quality across the U.S. is measured against them.

46 CFR 160.115-9 - Preapproval review.

Code of Federal Regulations, 2012 CFR

2012-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.115-19 and 160.115-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR part 159, subpart 159.010. (d) Plan quality...

46 CFR 160.115-9 - Preapproval review.

Code of Federal Regulations, 2014 CFR

2014-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.115-19 and 160.115-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR part 159, subpart 159.010. (d) Plan quality...

46 CFR 160.115-9 - Preapproval review.

Code of Federal Regulations, 2013 CFR

2013-10-01

... inventory of materials; (iii) The method for checking quality of fabrication and joints, including welding... §§ 160.115-19 and 160.115-21 of this subpart; (5) A description of the quality control procedures and... between the independent laboratory and Commandant under 46 CFR part 159, subpart 159.010. (d) Plan quality...

77 FR 60914 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Attainment Demonstration...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-05

... ambient air quality standard (NAAQS) for the Philadelphia-Wilmington-Atlantic City, PA-NJ- MD-DE moderate...).) List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Incorporation by... Promulgation of Air Quality Implementation Plans; Delaware; Attainment Demonstration for the 1997 8-Hour Ozone...

78 FR 882 - Approval and Promulgation of Air Quality Implementation Plans; Delaware, New Jersey, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-07

...)(2).) List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control... 2011 ambient air quality data, the Philadelphia-Wilmington, PA-NJ-DE fine particulate matter (PM 2.5... 2011 ambient air quality data, the Philadelphia-Wilmington, PA-NJ-DE fine particulate matter (PM 2.5...

77 FR 39456 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Section 110(a)(2...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-03

... tribal law. List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, lead... the 2008 Lead National Ambient Air Quality Standards AGENCY: Environmental Protection Agency (EPA..., necessary to implement, maintain, and enforce the 2008 lead national ambient air quality standards (NAAQS...

Application of reiteration of Hankel singular value decomposition in quality control

NASA Astrophysics Data System (ADS)

Staniszewski, Michał; Skorupa, Agnieszka; Boguszewicz, Łukasz; Michalczuk, Agnieszka; Wereszczyński, Kamil; Wicher, Magdalena; Konopka, Marek; Sokół, Maria; Polański, Andrzej

2017-07-01

Medical centres are obliged to store past medical records, including the results of quality assurance (QA) tests of the medical equipment, which is especially useful in checking reproducibility of medical devices and procedures. Analysis of multivariate time series is an important part of quality control of NMR data. In this work we proposean anomaly detection tool based on Reiteration of Hankel Singular Value Decomposition method. The presented method was compared with external software and authors obtained comparable results.

Portable and wide-range solid-state transmission densitometer for quality control in film radiography

PubMed Central

Aramburo, Javier Morales; Gonzalez, Sigifredo Solano; Toledo, Jorge Toledo

2010-01-01

In biology, materials science, radiography quality control or film dosimetry in radiotherapy, a transmission densitometer is useful for measurements of optical density. The design proposed here is oriented to quality control in radiographic films. The instrument described here utilizes low-cost solid-state devices and is easy to construct. The use of 1-watt white light-emitting diode in this densitometer enables low power consumption and a cold light source. Moreover, the instrument does not need a reference light, which results in decreasing the number of parts and reducing the overall size of the apparatus. PMID:20927222

Mitochondrial quality control: decommissioning power plants in neurodegenerative diseases.

PubMed

Mukherjee, Rukmini; Chakrabarti, Oishee

2013-01-01

The cell has an intricate quality control system to protect its mitochondria from oxidative stress. This surveillance system is multi-tiered and comprises molecules that are present inside the mitochondria, in the cytosol, and in other organelles like the nucleus and endoplasmic reticulum. These molecules cross talk with each other and protect the mitochondria from oxidative stress. Oxidative stress is a fundamental part of early disease pathogenesis of neurodegenerative diseases. These disorders also damage the cellular quality control machinery that protects the cell against oxidative stress. This exacerbates the oxidative damage and causes extensive neuronal cell death that is characteristic of neurodegeneration.

21 CFR 820.40 - Document controls.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Document controls. 820.40 Section 820.40 Food and... QUALITY SYSTEM REGULATION Document Controls § 820.40 Document controls. Each manufacturer shall establish and maintain procedures to control all documents that are required by this part. The procedures shall...

21 CFR 820.40 - Document controls.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Document controls. 820.40 Section 820.40 Food and... QUALITY SYSTEM REGULATION Document Controls § 820.40 Document controls. Each manufacturer shall establish and maintain procedures to control all documents that are required by this part. The procedures shall...

21 CFR 820.40 - Document controls.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Document controls. 820.40 Section 820.40 Food and... QUALITY SYSTEM REGULATION Document Controls § 820.40 Document controls. Each manufacturer shall establish and maintain procedures to control all documents that are required by this part. The procedures shall...

21 CFR 820.40 - Document controls.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Document controls. 820.40 Section 820.40 Food and... QUALITY SYSTEM REGULATION Document Controls § 820.40 Document controls. Each manufacturer shall establish and maintain procedures to control all documents that are required by this part. The procedures shall...

21 CFR 820.40 - Document controls.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Document controls. 820.40 Section 820.40 Food and... QUALITY SYSTEM REGULATION Document Controls § 820.40 Document controls. Each manufacturer shall establish and maintain procedures to control all documents that are required by this part. The procedures shall...

Manufacturing Execution Systems: Examples of Performance Indicator and Operational Robustness Tools.

PubMed

Gendre, Yannick; Waridel, Gérard; Guyon, Myrtille; Demuth, Jean-François; Guelpa, Hervé; Humbert, Thierry

Manufacturing Execution Systems (MES) are computerized systems used to measure production performance in terms of productivity, yield, and quality. In the first part, performance indicator and overall equipment effectiveness (OEE), process robustness tools and statistical process control are described. The second part details some tools to help process robustness and control by operators by preventing deviations from target control charts. MES was developed by Syngenta together with CIMO for automation.

Process-based quality for thermal spray via feedback control

NASA Astrophysics Data System (ADS)

Dykhuizen, R. C.; Neiser, R. A.

2006-09-01

Quality control of a thermal spray system manufacturing process is difficult due to the many input variables that need to be controlled. Great care must be taken to ensure that the process remains constant to obtain a consistent quality of the parts. Control is greatly complicated by the fact that measurement of particle velocities and temperatures is a noisy stochastic process. This article illustrates the application of quality control concepts to a wire flame spray process. A central feature of the real-time control system is an automatic feedback control scheme that provides fine adjustments to ensure that uncontrolled variations are accommodated. It is shown how the control vectors can be constructed from simple process maps to independently control particle velocity and temperature. This control scheme is shown to perform well in a real production environment. We also demonstrate that slight variations in the feed wire curvature can greatly influence the process. Finally, the geometry of the spray system and sensor must remain constant for the best reproducibility.

Cost Effective Prototyping

NASA Technical Reports Server (NTRS)

Wickman, Jerry L.; Kundu, Nikhil K.

1996-01-01

This laboratory exercise seeks to develop a cost effective prototype development. The exercise has the potential of linking part design, CAD, mold development, quality control, metrology, mold flow, materials testing, fixture design, automation, limited parts production and other issues as related to plastics manufacturing.

40 CFR Appendix F to Part 60 - Quality Assurance Procedures

Code of Federal Regulations, 2012 CFR

2012-07-01

... automatically adjust the data to the corrected calibration values (e.g., microprocessor control) must be... calibration values (e.g., microprocessor control), you must program your PM CEMS to record the unadjusted...

Setting and Reviewing Standards to Control Lead (Pb) Pollution

EPA Pesticide Factsheets

Lead (Pb) standards are part of the National Ambient Air Quality Standards (NAAQS), which limit air pollution to protect health and the environment. Standards are periodically reviewed and updated, and air quality across the U.S. is measured against them.

An Effective Quality Control of Pharmacologically Active Volatiles of Houttuynia cordata Thunb by Fast Gas Chromatography-Surface Acoustic Wave Sensor.

PubMed

Oh, Se Yeon

2015-06-03

Fast gas chromatography-surface acoustic wave sensor (GC/SAW) has been applied for the detection of the pharmacological volatiles emanated from Houttuynia cordata Thunb which is from South Korea. H. cordata Thunb with unpleasant and fishy odors shows a variety of pharmacological activities such as anti-microbial, anti-inflammatory, anti-cancer, and insect repellent. The aim of this study is to show a novel quality control by GC/SAW methodology for the discrimination of the three different parts of the plant such as leaves, aerial stems, and underground stems for H. cordata Thunb. Sixteen compounds were identified. β-Myrcene, cis-ocimene and decanal are the dominant volatiles for leaves (71.0%) and aerial stems (50.1%). While, monoterpenes (74.6%) are the dominant volatiles for underground stems. 2-Undecanone (1.3%) and lauraldehyde (3.5%) were found to be the characteristic components for leaves. Each part of the plant has its own characteristic fragrance pattern owing to its individual chemical compositions. Moreover, its individual characteristic fragrance patterns are conducive to discrimination of the three different parts of the plant. Consequently, fast GC/SAW can be a useful analytical method for quality control of the different parts of the plant with pharmacological volatiles as it provides second unit analysis, a simple and fragrant pattern recognition.

Electrical, Electronic, and Electromechanical (EEE) parts management and control requirements for NASA space flight programs

NASA Technical Reports Server (NTRS)

1989-01-01

This document establishes electrical, electronic, and electromechanical (EEE) parts management and control requirements for contractors providing and maintaining space flight and mission-essential or critical ground support equipment for NASA space flight programs. Although the text is worded 'the contractor shall,' the requirements are also to be used by NASA Headquarters and field installations for developing program/project parts management and control requirements for in-house and contracted efforts. This document places increased emphasis on parts programs to ensure that reliability and quality are considered through adequate consideration of the selection, control, and application of parts. It is the intent of this document to identify disciplines that can be implemented to obtain reliable parts which meet mission needs. The parts management and control requirements described in this document are to be selectively applied, based on equipment class and mission needs. Individual equipment needs should be evaluated to determine the extent to which each requirement should be implemented on a procurement. Utilization of this document does not preclude the usage of other documents. The entire process of developing and implementing requirements is referred to as 'tailoring' the program for a specific project. Some factors that should be considered in this tailoring process include program phase, equipment category and criticality, equipment complexity, and mission requirements. Parts management and control requirements advocated by this document directly support the concept of 'reliability by design' and are an integral part of system reliability and maintainability. Achieving the required availability and mission success objectives during operation depends on the attention given reliability and maintainability in the design phase. Consequently, it is intended that the requirements described in this document are consistent with those of NASA publications, 'Reliability Program Requirements for Aeronautical and Space System Contractors,' NHB 5300.4(1A-l); 'Maintainability Program Requirements for Space Systems,' NHB 5300.4(1E); and 'Quality Program Provisions for Aeronautical and Space System Contractors,' NHB 5300.4(1B).

Objective Speech Quality Assessment Based on Payload Discrimination of Lost Packets for Cellular Phones in NGN Environment

NASA Astrophysics Data System (ADS)

Uemura, Satoshi; Fukumoto, Norihiro; Yamada, Hideaki; Nakamura, Hajime

A feature of services provided in a Next Generation Network (NGN) is that the end-to-end quality is guaranteed. This is quite a challenging issue, given the considerable fluctuation in network conditions within a Fixed Mobile Convergence (FMC) network. Therefore, a novel approach, whereby a network node and a mobile terminal such as a cellular phone cooperate with each other to control service quality is essential. In order to achieve such cooperation, the mobile terminal needs to become more intelligent so it can estimate the service quality, including the user's perceptual quality, and notify the measurement result to the network node. Subsequently, the network node implements some kind of service control function, such as a resource and admission control function, based on the notification from the mobile terminal. In this paper, the role of the mobile terminal in such collaborative system is focused on. As a part of a QoS/QoE measurement system, we describe an objective speech quality assessment with payload discrimination of lost packets to measure the user's perceptual quality of VoIP. The proposed assessment is so simple that it can be implemented on a cellular phone. We therefore did this as part of the QoS/QoE measurement system. By using the implemented system, we can measure the user's perceptual quality of VoIP as well as the network QoS metrics, in terms of criteria such as packet loss rate, jitter and burstiness in real time.

Local Quality Work in an Age of Accountability--Between Autonomy and Control

ERIC Educational Resources Information Center

Bergh, Andreas

2015-01-01

This article analyses a specific part of the actions taken to improve the quality of Swedish education, namely the expectations formulated in national policy documents for the quality work that local authorities, schools and teachers are supposed to undertake. For the empirical analysis of how these expectations have changed over the last two…

“A manager in the minds of doctors:” a comparison of new modes of control in European hospitals

PubMed Central

2013-01-01

Background Hospital governance increasingly combines management and professional self-governance. This article maps the new emergent modes of control in a comparative perspective and aims to better understand the relationship between medicine and management as hybrid and context-dependent. Theoretically, we critically review approaches into the managerialism-professionalism relationship; methodologically, we expand cross-country comparison towards the meso-level of organisations; and empirically, the focus is on processes and actors in a range of European hospitals. Methods The research is explorative and was carried out as part of the FP7 COST action IS0903 Medicine and Management, Working Group 2. Comprising seven European countries, the focus is on doctors and public hospitals. We use a comparative case study design that primarily draws on expert information and document analysis as well as other secondary sources. Results The findings reveal that managerial control is not simply an external force but increasingly integrated in medical professionalism. These processes of change are relevant in all countries but shaped by organisational settings, and therefore create different patterns of control: (1) ‘integrated’ control with high levels of coordination and coherent patterns for cost and quality controls; (2) ‘partly integrated’ control with diversity of coordination on hospital and department level and between cost and quality controls; and (3) ‘fragmented’ control with limited coordination and gaps between quality control more strongly dominated by medicine, and cost control by management. Conclusions Our comparison highlights how organisations matter and brings the crucial relevance of ‘coordination’ of medicine and management across the levels (hospital/department) and the substance (cost/quality-safety) of control into perspective. Consequently, coordination may serve as a taxonomy of emergent modes of control, thus bringing new directions for cost-efficient and quality-effective hospital governance into perspective. PMID:23819578

77 FR 47581 - Revisions to the California State Implementation Plan, Mojave Desert, Northern Sierra, Sacramento...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-09

...EPA is proposing to approve revisions to the Mojave Desert Air Quality Management District (MDAQMD), Northern Sierra Air Quality Management District (NSAQMD), Sacramento Metropolitan Air Quality Management District (SMAQMD) and San Diego County Air Pollution Control District (SDCAPCD) portions of the California State Implementation Plan (SIP). These revisions concern volatile organic compound (VOC) emissions from automotive parts and component, automobile refinishing, metal parts and products, and miscellaneous coating and refinishing operations. We are proposing to approve local rules to regulate these emission sources under the Clean Air Act as amended in 1990 (CAA or the Act).

Improved process robustness by using closed loop control in deep drawing applications

NASA Astrophysics Data System (ADS)

Barthau, M.; Liewald, M.; Christian, Held

2017-09-01

The production of irregular shaped deep-drawing parts with high quality requirements, which are common in today’s automotive production, permanently challenges production processes. High requirements on lightweight construction of passenger car bodies following European regulations until 2020 have been massively increasing the use of high strength steels substantially for years and are also leading to bigger challenges in sheet metal part production. Of course, the more and more complex shapes of today’s car body shells also intensify the issue due to modern and future design criteria. The metal forming technology tries to meet these challenges by developing a highly sophisticated layout of deep drawing dies that consider part quality requirements, process robustness and controlled material flow during the deep or stretch drawing process phase. A new method for controlling material flow using a closed loop system was developed at the IFU Stuttgart. In contrast to previous approaches, this new method allows a control intervention during the deep-drawing stroke. The blank holder force around the outline of the drawn part is used as control variable. The closed loop is designed as trajectory follow up with feed forward control. The used command variable is the part-wall stress that is measured with a piezo-electric measuring pin. In this paper the used control loop will be described in detail. The experimental tool that was built for testing the new control approach is explained here with its features. A method for gaining the follow up trajectories from simulation will also be presented. Furthermore, experimental results considering the robustness of the deep drawing process and the gain in process performance with developed control loop will be shown. Finally, a new procedure for the industrial application of the new control method of deep drawing will be presented by using a new kind of active element to influence the local blank holder pressure onto part flange.

Assessment of air quality benefits from national air pollution control policies in China. Part II: Evaluation of air quality predictions and air quality benefits assessment

NASA Astrophysics Data System (ADS)

Wang, Litao; Jang, Carey; Zhang, Yang; Wang, Kai; Zhang, Qiang; Streets, David; Fu, Joshua; Lei, Yu; Schreifels, Jeremy; He, Kebin; Hao, Jiming; Lam, Yun-Fat; Lin, Jerry; Meskhidze, Nicholas; Voorhees, Scott; Evarts, Dale; Phillips, Sharon

2010-09-01

Following the meteorological evaluation in Part I, this Part II paper presents the statistical evaluation of air quality predictions by the U.S. Environmental Protection Agency (U.S. EPA)'s Community Multi-Scale Air Quality (Models-3/CMAQ) model for the four simulated months in the base year 2005. The surface predictions were evaluated using the Air Pollution Index (API) data published by the China Ministry of Environmental Protection (MEP) for 31 capital cities and daily fine particulate matter (PM 2.5, particles with aerodiameter less than or equal to 2.5 μm) observations of an individual site in Tsinghua University (THU). To overcome the shortage in surface observations, satellite data are used to assess the column predictions including tropospheric nitrogen dioxide (NO 2) column abundance and aerosol optical depth (AOD). The result shows that CMAQ gives reasonably good predictions for the air quality. The air quality improvement that would result from the targeted sulfur dioxide (SO 2) and nitrogen oxides (NO x) emission controls in China were assessed for the objective year 2010. The results show that the emission controls can lead to significant air quality benefits. SO 2 concentrations in highly polluted areas of East China in 2010 are estimated to be decreased by 30-60% compared to the levels in the 2010 Business-As-Usual (BAU) case. The annual PM 2.5 can also decline by 3-15 μg m -3 (4-25%) due to the lower SO 2 and sulfate concentrations. If similar controls are implemented for NO x emissions, NO x concentrations are estimated to decrease by 30-60% as compared with the 2010 BAU scenario. The annual mean PM 2.5 concentrations will also decline by 2-14 μg m -3 (3-12%). In addition, the number of ozone (O 3) non-attainment areas in the northern China is projected to be much lower, with the maximum 1-h average O 3 concentrations in the summer reduced by 8-30 ppb.

Distributed sensor architecture for intelligent control that supports quality of control and quality of service.

PubMed

Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

2015-02-25

This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems.

Distributed Sensor Architecture for Intelligent Control that Supports Quality of Control and Quality of Service

PubMed Central

Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

2015-01-01

This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems. PMID:25723145

78 FR 77094 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-20

..., Office of Management and Budget (OMB), [email protected] or fax (202) 395-5806 and to... it displays a currently valid OMB control number. Food and Nutrition Service Title: Supplemental Nutrition Assistance Program Regulations, Part 275--Quality Control. OMB Control Number: 0584-0303. Summary...

Mutuality Meets the Market: Analysing Changes in the Control of Quality Assurance in United Kingdom Higher Education 1992-2012

ERIC Educational Resources Information Center

Brown, Roger

2013-01-01

There has been a tendency in the literature to see changes in quality assurance as part of a process of increased state control. This article suggests a more nuanced approach that also takes account of the different trajectories of the pre- and post-1992 sectors. It finds that whilst there have been increases in both state oversight and market…

Verification Testing of Air Pollution Control Technology Quality Management Plan Revision 2.3

EPA Pesticide Factsheets

The Air Pollution Control Technology Verification Center was established in 1995 as part of the EPA’s Environmental Technology Verification Program to accelerate the development and commercialization of improved environmental technologies’ performance.

Double-quality control reveals high-level toxicity in gloves used for operator protection in assisted reproductive technology.

PubMed

Lierman, Sylvie; De Sutter, Petra; Dhont, Marc; Van der Elst, Josiane

2007-10-01

To submit different glove brands to double-quality control tests using mouse embryo assay (MEA) and the human sperm motility assay (HuSMA). Operator protection against infectious body fluid contamination is a safety issue in assisted reproductive technology (ART). When using gloves in the ART laboratory, toxic substances can be transmitted to culture media, even during brief contact. Quality control study of gloves in ART. University hospital-based infertility center. Seven- to 8-week-old female B6D2F1 hybrid mice. We tested two surgical, two cleanroom, and six examination glove brands. Only gloves brands that passed both HuSMA and MEA were submitted to further QC using zona-free and/or cryopreserved MEA. Sperm motility index, two-cell and blastocyst development, blastocyst total cell number. Quality control by MEA and HuSMA identified two glove brands to be nontoxic. Our study shows that gloves used in ART can be toxic and should be tested as part of an ongoing quality control program.

Quality Audit in the Fastener Industry

NASA Technical Reports Server (NTRS)

Reagan, John R.

1995-01-01

Both the financial and quality communities rely on audits to verify customers records. The financial community is highly structured around three categories of risk, INHERENT RISK, CONTROL RISK, and DETECTION RISK. Combined, the product of these three categories constitute the AUDIT RISK. The financial community establishes CONTROL RISK based in large part on a systems level understanding of the process flow. This system level understanding is best expressed in a flowchart. The quality community may be able to adopt this structure and thereby reduce cost while maintaining and enhancing quality. The quality community should attempt to flowchart the systems level quality process before beginning substantive testing. This theory needs to be applied in several trial cases to prove or disprove this hypothesis

Quality audit in the fastener industry

NASA Astrophysics Data System (ADS)

Reagan, John R.

1995-09-01

Both the financial and quality communities rely on audits to verify customers records. The financial community is highly structured around three categories of risk, INHERENT RISK, CONTROL RISK, and DETECTION RISK. Combined, the product of these three categories constitute the AUDIT RISK. The financial community establishes CONTROL RISK based in large part on a systems level understanding of the process flow. This system level understanding is best expressed in a flowchart. The quality community may be able to adopt this structure and thereby reduce cost while maintaining and enhancing quality. The quality community should attempt to flowchart the systems level quality process before beginning substantive testing. This theory needs to be applied in several trial cases to prove or disprove this hypothesis

Part-Time Faculty Evaluation: A Campus Case Study.

ERIC Educational Resources Information Center

Williams, James P.

For the past 13 years, the Verde Valley Campus of Yavapai College, in Arizona, has used the same system to evaluate part-time faculty in an effort to both maintain quality control and provide feedback to part-time faculty and address their concerns. The system utilizes two instruments to gather evaluative data. The first is used to determine…

Poor sleep quality has an adverse effect on childhood asthma control and lung function measures.

PubMed

Sheen, Youn Ho; Choi, Sun Hee; Jang, Sun Jung; Baek, Ji Hyeon; Jee, Hye Mi; Kim, Mi Ae; Chae, Kyu Young; Han, Man Yong

2017-08-01

It is unclear as to whether sleep respiratory breathing disorder (SRBD) is a risk factor for uncontrolled asthma in children. The aim of this study was therefore to investigate whether SRBD may have an adverse effect on childhood asthma control and lung function measures. This was a cross-sectional study of 220 children with well-controlled (n = 108), partly controlled (n = 92), and uncontrolled asthma (n = 20) according to the Global Initiative for Asthma guideline. SRBD was assessed using the Pediatric Sleep Questionnaire (PSQ). The association of SRBD with partly controlled/uncontrolled asthma was investigated on multivariate logistic regression analysis. Of 220 children with asthma, 43 (19.6%) had SRBD: well-controlled, 16.7% (18/108); partly controlled, 21.7% (20/92); and uncontrolled, 25.0% (5/20; P = 0.54). There was a significant difference in forced expiratory volume in 1 s/forced vital capacity (FEV 1 /FVC; P = 0.007) and childhood asthma control test (C-ACT) score (P < 0.001) according to asthma control status, but not in PSQ score (P = 0.18). Children with obstructive sleep apnea (PSQ >0.33) had a lower C-ACT score compared with controls (PSQ ≤0.33; 19.6 ± 5.1 vs 22.0 ± 4.2, P = 0.002). PSQ score was negatively correlated with FEV 1 /FVC (r = -0.16, P = 0.02). On multivariate logistic regression analysis, high PSQ score increased the odds of having partly controlled/uncontrolled asthma by 9.12 (95% CI: 1.04-79.72, P = 0.046) after adjusting for confounding factors. SRBD is an independent risk factor for partly controlled/uncontrolled asthma and has an adverse effect on lung function measures in children. Further research is warranted to determine whether the improvement of sleep quality may also enhance level of asthma control and lung function in children. © 2017 Japan Pediatric Society.

Some aspects of precise laser machining - Part 2: Experimental

NASA Astrophysics Data System (ADS)

Grabowski, Marcin; Wyszynski, Dominik; Ostrowski, Robert

2018-05-01

The paper describes the role of laser beam polarization on quality of laser beam machined cutting tool edge. In micromachining the preparation of the cutting tools in play a key role on dimensional accuracy, sharpness and the quality of the cutting edges. In order to assure quality and dimensional accuracy of the cutting tool edge it is necessary to apply laser polarization control. In the research diode pumped Nd:YAG 532nm pulse laser was applied. Laser beam polarization used in the research was linear (horizontal, vertical). The goal of the carried out research was to describe impact of laser beam polarization on efficiency of the cutting process and quality of machined parts (edge, surface) made of polycrystalline diamond (PCD) and cubic boron nitride (cBN). Application of precise cutting tool in micromachining has significant impact on the minimum uncut chip thickness and quality of the parts. The research was carried within the INNOLOT program funded by the National Centre for Research and Development.

Health-related effects of early part-time sick leave due to musculoskeletal disorders: a randomized controlled trial.

PubMed

Shiri, Rahman; Kausto, Johanna; Martimo, Kari-Pekka; Kaila-Kangas, Leena; Takala, Esa-Pekka; Viikari-Juntura, Eira

2013-01-01

Previously we reported that early part-time sick leave enhances return to work (RTW) among employees with musculoskeletal disorders (MSD). This paper assesses the health-related effects of this intervention. Patients aged 18-60 years who were unable to perform their regular work due to MSD were randomized to part- or full-time sick leave groups. In the former, workload was reduced by halving working time. Using validated questionnaires, we assessed pain intensity and interference with work and sleep, region-specific disability due to MSD, self-rated general health, health-related quality of life (measured via EuroQol), productivity loss, depression, and sleep disturbance at baseline, 1, 3, 8, 12, and 52 weeks. We analyzed the repeated measures data (171-356 observations) with the generalized estimating equation approach. The intervention (part-time sick leave) and control (full-time sick leave) groups did not differ with regard to pain intensity, pain interference with work and sleep, region-specific disability, productivity loss, depression, or sleep disturbance. The intervention group reported better self-rated general health (adjusted P=0.07) and health-related quality of life (adjusted P=0.02) than the control group. In subgroup analyses, the intervention was more effective among the patients whose current problem began occurring <6 weeks before baseline and those with ≤30% productivity loss at baseline. Our findings showed that part-time sick leave did not exacerbate pain-related symptoms and functional disability, but improved self-rated general health and health-related quality of life in the early stage of work disability due to MSD.

Quality Leadership and Quality Control

PubMed Central

Badrick, Tony

2003-01-01

Different quality control rules detect different analytical errors with varying levels of efficiency depending on the type of error present, its prevalence and the number of observations. The efficiency of a rule can be gauged by inspection of a power function graph. Control rules are only part of a process and not an end in itself; just as important are the trouble-shooting systems employed when a failure occurs. 'Average of patient normals' may develop as a usual adjunct to conventional quality control serum based programmes. Acceptable error can be based on various criteria; biological variation is probably the most sensible. Once determined, acceptable error can be used as limits in quality control rule systems. A key aspect of an organisation is leadership, which links the various components of the quality system. Leadership is difficult to characterise but its key aspects include trust, setting an example, developing staff and critically setting the vision for the organisation. Organisations also have internal characteristics such as the degree of formalisation, centralisation, and complexity. Medical organisations can have internal tensions because of the dichotomy between the bureaucratic and the shadow medical structures. PMID:18568046

76 FR 9787 - NIOSH Dose Reconstruction Program Ten Year Review-Phase I Report on Quality of Science; Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-22

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention NIOSH Dose Reconstruction Program Ten Year Review--Phase I Report on Quality of Science; Request for Public Review and... Ten Year Review--Phase I Report on Quality of Science.'' This publication is part of a review by NIOSH...

12 CFR 1815.115 - OMB control number.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 9 2013-01-01 2013-01-01 false OMB control number. 1815.115 Section 1815.115... ENVIRONMENTAL QUALITY § 1815.115 OMB control number. The collection of information requirements in this part have been approved by the Office of Management and Budget and assigned OMB control number 1505-0153...

40 CFR 130.11 - Program management.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quality standards (WQS), development of alternative approaches to control pollution, implementation and... primarily to manage the wastewater treatment works construction grants program pursuant to the provisions of 40 CFR part 35, subpart J. A State may also use part of the 205(g) funds to administer approved...

78 FR 5290 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Reasonably Available...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-25

...: Paper, film, and foil coatings; industrial cleaning solvents; miscellaneous metal and plastic parts... solvents; (3) miscellaneous metal and plastic parts coatings; (4) large appliance coatings; (5) offset... protection, Air pollution control, Incorporation by reference, Intergovernmental relations, Ozone, Reporting...

Laser Ultrasound Spectroscopy Scanning for 3D Printed Parts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brennan, Guendalyn Kendra

One of the challenges of additive manufacturing is quality control due to the possibility of unseen flaws in the final product. The current methods of inspection are lacking in detail, too slow for practical use, or unable to validate internal structure. This report examines the use of laser ultrasound spectroscopy in layer by layer scans of 3D printed parts as they are created. The result is fast and detailed quality control. An additional advantage of this method is the ability to cancel a print as soon as a defect is detected, therefore saving materials and time. This technique, though simplemore » in concept, has been a challenge to implement. I discuss tweaking the 3D printer configuration, and finding the optimal settings for laser scanning small parts made of ABS plastic, as well as the limits of how small of a detail the laser can detect. These settings include the frequency of the ultrasonic transducer, the speed of the laser, and the distance from the laser to the part.« less

77 FR 46960 - Approval and Promulgation of Air Quality Implementation Plans; Wisconsin; Forest County...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-07

... Promulgation of Air Quality Implementation Plans; Wisconsin; Forest County Potawatomi Community Reservation... approving procedures for permitting certain sources in relation to the Forest County Potawatomi Community...)(2).) List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Carbon...

Rebuilding Habitat and Shoreline Resilience through Improved Flood Control Project

EPA Pesticide Factsheets

Information about the SFBWQP Rebuilding Habitat and Shoreline Resilience through Improved Flood Control Project, part of an EPA competitive grant program to improve SF Bay water quality focused on restoring impaired waters and enhancing aquatic resources.

76 FR 51901 - Approval and Promulgation of Air Quality Implementation Plans; Ohio; Control of Emissions of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-19

... was part of Ohio's SIP, was rescinded by Ohio EPA. The most significant problem with the prior version...-21-25 ``Control of VOC emissions from reinforced plastic composites production operations,'' which...

Selected Aspects Of The Risk In The Supply Chain In Context Of The Supplier Quality Management

NASA Astrophysics Data System (ADS)

Koblen, Ivan; Lestyánszka Škůrková, Katarína

2015-06-01

The introductory part of the paper underlines the importance of "Risk-based thinking" in the Quality Management System (QMS) and risk in the supply chain, as a principle part of the QMS. After introducing the key terms, the authors focused on the principle part of the article - explanation of the external and internal supply chain risks and the main factors concerning the supply risks, demand risks and environmental risks (as cardinal types of external supply chain risks) as well as the manufacturing and process risks, network/planning and control risks (as most important types of internal supply chain risks). The authors inform on the selected supply chain risk management tools, especially on those which are linked to the appropriate utilization of quality management tools.

Mesh control information of windmill designed by Solidwork program

NASA Astrophysics Data System (ADS)

Mulyana, T.; Sebayang, D.; Rafsanjani, A. M. D.; Adani, J. H. D.; Muhyiddin, Y. S.

2017-12-01

This paper presents the mesh control information imposed on the windmill already designed. The accuracy of Simulation results is influenced by the quality of the created mesh. However, compared to the quality of the mesh is made, the simulation time running will be done software also increases. The smaller the size of the elements created when making the mesh, the better the mesh quality will be generated. When adjusting the mesh size, there is a slider that acts as the density regulator of the element. SolidWorks Simulation also has Mesh Control facility. Features that can adjust mesh density only in the desired part. The best results of mesh control obtained for both static and thermal simulation have ratio 1.5.

Microbiological water methods: quality control measures for Federal Clean Water Act and Safe Drinking Water Act regulatory compliance.

PubMed

Root, Patsy; Hunt, Margo; Fjeld, Karla; Kundrat, Laurie

2014-01-01

Quality assurance (QA) and quality control (QC) data are required in order to have confidence in the results from analytical tests and the equipment used to produce those results. Some AOAC water methods include specific QA/QC procedures, frequencies, and acceptance criteria, but these are considered to be the minimum controls needed to perform a microbiological method successfully. Some regulatory programs, such as those at Code of Federal Regulations (CFR), Title 40, Part 136.7 for chemistry methods, require additional QA/QC measures beyond those listed in the method, which can also apply to microbiological methods. Essential QA/QC measures include sterility checks, reagent specificity and sensitivity checks, assessment of each analyst's capabilities, analysis of blind check samples, and evaluation of the presence of laboratory contamination and instrument calibration and checks. The details of these procedures, their performance frequency, and expected results are set out in this report as they apply to microbiological methods. The specific regulatory requirements of CFR Title 40 Part 136.7 for the Clean Water Act, the laboratory certification requirements of CFR Title 40 Part 141 for the Safe Drinking Water Act, and the International Organization for Standardization 17025 accreditation requirements under The NELAC Institute are also discussed.

Low cost composite manufacturing utilizing intelligent pultrusion and resin transfer molding (IPRTM)

NASA Astrophysics Data System (ADS)

Bradley, James E.; Wysocki, Tadeusz S., Jr.

1993-02-01

This article describes an innovative method for the economical manufacturing of large, intricately-shaped tubular composite parts. Proprietary intelligent process control techniques are combined with standard pultrusion and RTM methodologies to provide high part throughput, performance, and quality while substantially reducing scrap, rework costs, and labor requirements. On-line process monitoring and control is achieved through a smart tooling interface consisting of modular zone tiles installed on part-specific die assemblies. Real-time archiving of process run parameters provides enhanced SPC and SQC capabilities.

10 CFR Appendix B to Part 50 - Quality Assurance Criteria for Nuclear Power Plants and Fuel Reprocessing Plants

Code of Federal Regulations, 2012 CFR

2012-01-01

... executing. III. Design Control Measures shall be established to assure that applicable regulatory... control of design interfaces and for coordination among participating design organizations. These measures..., approval, release, distribution, and revision of documents involving design interfaces. The design control...

10 CFR Appendix B to Part 50 - Quality Assurance Criteria for Nuclear Power Plants and Fuel Reprocessing Plants

Code of Federal Regulations, 2013 CFR

2013-01-01

... executing. III. Design Control Measures shall be established to assure that applicable regulatory... control of design interfaces and for coordination among participating design organizations. These measures..., approval, release, distribution, and revision of documents involving design interfaces. The design control...

75 FR 8246 - Approval and Promulgation of Air Quality Implementation Plans; Indiana; Volatile Organic Compound...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-24

...)(2).) List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control...) Incorporation by reference. (A) Indiana Administrative Code Title 326: Air Pollution Control Board, Article 8..., 2009 (DIN: 20091202-IR-326090220FRA). (B) Indiana Administrative Code Title 326: Air Pollution Control...

76 FR 11983 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-04

... state and local air pollution control authorities information that should assist them in determining...; plastic asceptic packaging; and carbon paper and inked ribbons. VOC emissions from paper, film, or foil... of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Incorporation by...

76 FR 71886 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-21

... the California State Implementation Plan, Placer County Air Pollution Control District and Sacramento... Pollution Control District (PCAPCD) and Sacramento Metropolitan Air Quality Management District (SMAQMD... Guidelines for Miscellaneous Metal and Plastic Parts Coatings,'' EPA-453/R-08-003, September 2008. 7...

78 FR 13493 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Revision to...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-28

... Pennsylvania. This revision pertains to the Air Pollution Control portion of the Allegheny County Health... pertaining to the Air Pollution Control portion of the Allegheny County Health Department (ACHD) Rules and... of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Carbon monoxide...

Quality Control and Analysis of Microphysical Data Collected in TRMM Aircraft Validation Experiments

NASA Technical Reports Server (NTRS)

Heymsfield, Andrew J.

2004-01-01

This report summarizes our efforts on the funded project 'Quality Control and Analysis of Microphysical Data Collected in TRMM Airborne Validation Experiments', NASA NAG5-9663, Andrew Heymsfield, P. I. We begin this report by summarizing our activities in FY2000-FY2004. We then present some highlights of our work. The last part of the report lists the publications that have resulted from our funding through this grant.

77 FR 64787 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Reasonably Available...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-23

... and plastic parts coatings; large appliance coatings; offset lithographic printing and letterpress... local air pollution control authorities information that should assist them in determining RACT for VOC... plastic parts coatings; (4) large appliance coatings; (5) offset lithographic printing and letterpress...

40 CFR 63.9808 - How do I monitor and collect data to demonstrate continuous compliance?

Code of Federal Regulations, 2010 CFR

2010-07-01

... times, you must maintain your monitoring systems including, but not limited to, maintaining necessary parts for routine repairs of the monitoring equipment. (c) Except for, as applicable, monitoring system malfunctions, associated repairs, and required quality assurance or quality control activities, you must...

40 CFR 63.9808 - How do I monitor and collect data to demonstrate continuous compliance?

Code of Federal Regulations, 2014 CFR

2014-07-01

... times, you must maintain your monitoring systems including, but not limited to, maintaining necessary parts for routine repairs of the monitoring equipment. (c) Except for, as applicable, monitoring system malfunctions, associated repairs, and required quality assurance or quality control activities, you must...

40 CFR 63.9808 - How do I monitor and collect data to demonstrate continuous compliance?

Code of Federal Regulations, 2012 CFR

2012-07-01

... times, you must maintain your monitoring systems including, but not limited to, maintaining necessary parts for routine repairs of the monitoring equipment. (c) Except for, as applicable, monitoring system malfunctions, associated repairs, and required quality assurance or quality control activities, you must...

40 CFR 63.9808 - How do I monitor and collect data to demonstrate continuous compliance?

Code of Federal Regulations, 2011 CFR

2011-07-01

... times, you must maintain your monitoring systems including, but not limited to, maintaining necessary parts for routine repairs of the monitoring equipment. (c) Except for, as applicable, monitoring system malfunctions, associated repairs, and required quality assurance or quality control activities, you must...

40 CFR 63.9808 - How do I monitor and collect data to demonstrate continuous compliance?

Code of Federal Regulations, 2013 CFR

2013-07-01

... times, you must maintain your monitoring systems including, but not limited to, maintaining necessary parts for routine repairs of the monitoring equipment. (c) Except for, as applicable, monitoring system malfunctions, associated repairs, and required quality assurance or quality control activities, you must...

30 CFR 250.302 - Definitions concerning air quality.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and 250.304 of this part: Air pollutant means any combination of agents for which the Environmental... shown by monitored data or which is calculated by air quality modeling (or other methods determined by... standards established by EPA. Best available control technology (BACT) means an emission limitation based on...

78 FR 9828 - Approval and Promulgation of Implementation Plans; New Mexico; Albuquerque/Bernalillo County...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-12

... Promulgation of Implementation Plans; New Mexico; Albuquerque/Bernalillo County: Infrastructure and Interstate... State State citation Title/subject approval/ EPA approval date Explanation effective date New Mexico... Quality Control Board * * * * * * * Part 8 (20.11.8 NMAC) Ambient Air Quality 8/12/2009 September 19, 2012...

76 FR 27973 - Approval and Promulgation of Air Quality Implementation Plans; Indiana

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-13

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R05-OAR-2010-0999; FRL-9304-9] Approval and Promulgation of Air Quality Implementation Plans; Indiana AGENCY: Environmental Protection Agency (EPA). ACTION..., Control Strategies Section, Air Programs Branch (AR-18J), U.S. Environmental Protection Agency, Region 5...

The effects of a team-based continuous quality improvement intervention on the management of primary care: a randomised controlled trial

PubMed Central

Engels, Yvonne; van den Hombergh, Pieter; Mokkink, Henk; van den Hoogen, Henk; van den Bosch, Wil; Grol, Richard

2006-01-01

Aim To study the effects of a team-based model for continuous quality improvement (CQI) on primary care practice management. Design of study Randomised controlled trial. Setting Twenty-six intervention and 23 control primary care practices in the Netherlands. Method Practices interested in taking part in the CQI project were, after assessment of their practice organisation, randomly assigned to the intervention or control groups. During a total of five meetings, a facilitator helped the teams in the intervention group select suitable topics for quality improvement and follow a structured approach to achieve improvement objectives. Checklists completed by an outreach visitor, questionnaires for the GPs, staff and patients were used to assemble data on the number and quality of improvement activities undertaken and on practice management prior to the start of the intervention and 1 year later. Results Pre-test and post-test data were compared for the 26 intervention and 23 control practices. A significant intervention effect was found for the number of improvement objectives actually defined (93 versus 54, P<0.001) and successfully completed (80 versus 69% of the projects, P<0.001). The intervention group also improved on more aspects of practice management, as measured by our practice visit method, than the control group but none of these differences proved statistically significant. Conclusion The intervention exerted a significant effect on the number and quality of improvement projects undertaken and self-defined objectives met. Failure of the effects of the intervention on the other dimensions of practice management to achieve significance may be due to the topics selected for some of the improvement projects being only partly covered by the assessment instrument. PMID:17007709

Guidance and Control Software Project Data - Volume 4: Configuration Management and Quality Assurance Documents

NASA Technical Reports Server (NTRS)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes configuration management and quality assurance documents from the GCS project. Volume 4 contains six appendices: A. Software Accomplishment Summary for the Guidance and Control Software Project; B. Software Configuration Index for the Guidance and Control Software Project; C. Configuration Management Records for the Guidance and Control Software Project; D. Software Quality Assurance Records for the Guidance and Control Software Project; E. Problem Report for the Pluto Implementation of the Guidance and Control Software Project; and F. Support Documentation Change Reports for the Guidance and Control Software Project.

Statistical quality control through overall vibration analysis

NASA Astrophysics Data System (ADS)

Carnero, M. ^a. Carmen; González-Palma, Rafael; Almorza, David; Mayorga, Pedro; López-Escobar, Carlos

2010-05-01

The present study introduces the concept of statistical quality control in automotive wheel bearings manufacturing processes. Defects on products under analysis can have a direct influence on passengers' safety and comfort. At present, the use of vibration analysis on machine tools for quality control purposes is not very extensive in manufacturing facilities. Noise and vibration are common quality problems in bearings. These failure modes likely occur under certain operating conditions and do not require high vibration amplitudes but relate to certain vibration frequencies. The vibration frequencies are affected by the type of surface problems (chattering) of ball races that are generated through grinding processes. The purpose of this paper is to identify grinding process variables that affect the quality of bearings by using statistical principles in the field of machine tools. In addition, an evaluation of the quality results of the finished parts under different combinations of process variables is assessed. This paper intends to establish the foundations to predict the quality of the products through the analysis of self-induced vibrations during the contact between the grinding wheel and the parts. To achieve this goal, the overall self-induced vibration readings under different combinations of process variables are analysed using statistical tools. The analysis of data and design of experiments follows a classical approach, considering all potential interactions between variables. The analysis of data is conducted through analysis of variance (ANOVA) for data sets that meet normality and homoscedasticity criteria. This paper utilizes different statistical tools to support the conclusions such as chi squared, Shapiro-Wilks, symmetry, Kurtosis, Cochran, Hartlett, and Hartley and Krushal-Wallis. The analysis presented is the starting point to extend the use of predictive techniques (vibration analysis) for quality control. This paper demonstrates the existence of predictive variables (high-frequency vibration displacements) that are sensible to the processes setup and the quality of the products obtained. Based on the result of this overall vibration analysis, a second paper will analyse self-induced vibration spectrums in order to define limit vibration bands, controllable every cycle or connected to permanent vibration-monitoring systems able to adjust sensible process variables identified by ANOVA, once the vibration readings exceed established quality limits.

Rotorcraft flying qualities improvement using advanced control

NASA Technical Reports Server (NTRS)

Walker, D.; Postlethwaite, I.; Howitt, J.; Foster, N.

1993-01-01

We report on recent experience gained when a multivariable helicopter flight control law was tested on the Large Motion Simulator (LMS) at DRA Bedford. This was part of a study into the application of multivariable control theory to the design of full-authority flight control systems for high-performance helicopters. In this paper, we present some of the results that were obtained during the piloted simulation trial and from subsequent off-line simulation and analysis. The performance provided by the control law led to level 1 handling quality ratings for almost all of the mission task elements assessed, both during the real-time and off-line analysis.

Groundwater quality data from the National Water-Quality Assessment Project, May 2012 through December 2013

USGS Publications Warehouse

Arnold, Terri L.; Desimone, Leslie A.; Bexfield, Laura M.; Lindsey, Bruce D.; Barlow, Jeannie R.; Kulongoski, Justin T.; Musgrove, MaryLynn; Kingsbury, James A.; Belitz, Kenneth

2016-06-20

Groundwater-quality data were collected from 748 wells as part of the National Water-Quality Assessment Project of the U.S. Geological Survey National Water-Quality Program from May 2012 through December 2013. The data were collected from four types of well networks: principal aquifer study networks, which assess the quality of groundwater used for public water supply; land-use study networks, which assess land-use effects on shallow groundwater quality; major aquifer study networks, which assess the quality of groundwater used for domestic supply; and enhanced trends networks, which evaluate the time scales during which groundwater quality changes. Groundwater samples were analyzed for a large number of water-quality indicators and constituents, including major ions, nutrients, trace elements, volatile organic compounds, pesticides, and radionuclides. These groundwater quality data are tabulated in this report. Quality-control samples also were collected; data from blank and replicate quality-control samples are included in this report.

Methods for collecting benthic invertebrate samples as part of the National Water-Quality Assessment Program

USGS Publications Warehouse

Cuffney, Thomas F.; Gurtz, Martin E.; Meador, Michael R.

1993-01-01

Benthic invertebrate communities are evaluated as part of the ecological survey component of the U.S. Geological Survey's National Water-Quality Assessment Program. These biological data are collected along with physical and chemical data to assess water-quality conditions and to develop an understanding of the factors that affect water-quality conditions locally, regionally, and nationally. The objectives of benthic invertebrate community characterizations are to (1) develop for each site a list of tax a within the associated stream reach and (2) determine the structure of benthic invertebrate communities within selected habitats of that reach. A nationally consistent approach is used to achieve these objectives. This approach provides guidance on site, reach, and habitat selection and methods and equipment for qualitative multihabitat sampling and semi-quantitative single habitat sampling. Appropriate quality-assurance and quality-control guidelines are used to maximize the ability to analyze data within and among study units.

41 CFR 101-31.000 - Scope of part.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 2 2013-07-01 2012-07-01 true Scope of part. 101-31.000 Section 101-31.000 Public Contracts and Property Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 31-INSPECTION AND QUALITY CONTROL § 101-31...

41 CFR 101-31.000 - Scope of part.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 41 Public Contracts and Property Management 2 2011-07-01 2007-07-01 true Scope of part. 101-31.000 Section 101-31.000 Public Contracts and Property Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 31-INSPECTION AND QUALITY CONTROL § 101-31...

41 CFR 101-31.000 - Scope of part.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Scope of part. 101-31.000 Section 101-31.000 Public Contracts and Property Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 31-INSPECTION AND QUALITY CONTROL § 101-31...

41 CFR 101-31.000 - Scope of part.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 41 Public Contracts and Property Management 2 2014-07-01 2012-07-01 true Scope of part. 101-31.000 Section 101-31.000 Public Contracts and Property Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 31-INSPECTION AND QUALITY CONTROL § 101-31...

Mississippi SIP: Title 11, Part 2, Chapter 1 - Air Emission Regulations for the Prevention, Abatement and Control of Air Contaminents

EPA Pesticide Factsheets

Air Emission Regulations for the Prevention, Abatement and Control of Air Contaminents for areas involved in ambient air quality standards & regulations in MS + where to obtain copies of referenced federal regulations

Can exercise improve self esteem in children and young people? A systematic review of randomised controlled trials.

PubMed

Ekeland, E; Heian, F; Hagen, K B

2005-11-01

A systematic review to determine if exercise alone or as part of a comprehensive intervention can improve self esteem in children and young people is described. Twenty three randomised controlled trials were analysed. A synthesis of several small, low quality trials indicates that exercise may have short term beneficial effects on self esteem in children and adolescents. However, high quality research on defined populations with adequate follow up is needed.

USAF Test Pilot School. Flying Qualities Textbook, Volume 2, Part 1

DTIC Science & Technology

1986-04-01

Qualities Flight Testing, Performance and Flying Qaulities Branch, Flight Test Engneerd ision, 6510th Test Wing, Air Force Flight Mayst Ce1ter, Edwards...For these aircraft, the program manager may re*uire a mil spec written specifically for the aircraft and control system involwd. 5.20.2 _EL k,Tt...OR MANAGED IN CONTEXT OF MISSION, WITH AVAILABLE PILOT ATTENTION. S UNCONTROLLABLE CONTROL WILL BE LOST DURING SOME PORTION OF MISSION. ACCEPTABLE

Rocky Mountain Arsenal, Sanitary Sewer Interim Response Action, Construction Documents for New Sanitary Sewer Construction. Volume 2

DTIC Science & Technology

1990-05-01

curves ; test reports; test cylinders: samples, O&M manuals including parts lists; certifications; warranties and other such required submittals...purpose. 14.4.3. Authority and responsibilities of all quality control personnel. 14.4.4. Schedule of Use of inspection personnel by types and phase of...quality control program shall include four phases of inspection and tests. The Contracting Officer’s representative shall be notified at least 24

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kegel, T.M.

Calibration laboratories are faced with the need to become accredited or registered to one or more quality standards. One requirement common to all of these standards is the need to have in place a measurement assurance program. What is a measurement assurance program? Brian Belanger, in Measurement Assurance Programs: Part 1, describes it as a {open_quotes}quality assurance program for a measurement process that quantifies the total uncertainty of the measurements (both random and systematic components of error) with respect to national or designated standards and demonstrates that the total uncertainty is sufficiently small to meet the user`s requirements.{close_quotes} Rolf Schumachermore » is more specific in Measurement Assurance in Your Own Laboratory. He states, {open_quotes}Measurement assurance is the application of broad quality control principles to measurements of calibrations.{close_quotes} Here, the focus is on one important part of any measurement assurance program: implementation of statistical process control (SPC). Paraphrasing Juran`s Quality Control Handbook, a process is in statistical control if the only observed variations are those that can be attributed to random causes. Conversely, a process that exhibits variations due to assignable causes is not in a state of statistical control. Finally, Carrol Croarkin states, {open_quotes}In the measurement assurance context the measurement algorithm including instrumentation, reference standards and operator interactions is the process that is to be controlled, and its direct product is the measurement per se. The measurements are assumed to be valid if the measurement algorithm is operating in a state of control.{close_quotes} Implicit in this statement is the important fact that an out-of-control process cannot produce valid measurements. 7 figs.« less

Combat Ration Advanced Manufacturing Technology Demonstration (CRAMTD). ’Generic Inspection-Statistical Process Control System for a Combat Ration Manufacturing Facility’. Short Term Project (STP) Number 3.

DTIC Science & Technology

1996-01-01

failure as due to an adhesive layer between the foil and inner polypropylene layers. "* Under subcontract, NFPA provided HACCP draft manuals for the...parameters of the production process and to ensure that they are within their target values. In addition, a HACCP program was used to assure product...played an important part in implementing Hazard Analysis Critical Control Points ( HACCP ) as part of the Process and Quality Control manual. The National

Process and control systems for composites manufacturing

NASA Technical Reports Server (NTRS)

Tsiang, T. H.; Wanamaker, John L.

1992-01-01

A precise control of composite material processing would not only improve part quality, but it would also directly reduce the overall manufacturing cost. The development and incorporation of sensors will help to generate real-time information for material processing relationships and equipment characteristics. In the present work, the thermocouple, pressure transducer, and dielectrometer technologies were investigated. The monitoring sensors were integrated with the computerized control system in three non-autoclave fabrication techniques: hot-press, self contained tool (self heating and pressurizing), and pressure vessel). The sensors were implemented in the parts and tools.

76 FR 67396 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-01

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R09-OAR-2011-0382; FRL-9477-3] Revisions to the California State Implementation Plan, Placer County Air Pollution Control District AGENCY... the Placer County Air Pollution Control District (PCAPCD) and Sacramento Metro Air Quality Management...

76 FR 69927 - Approval of Air Quality Implementation Plans; California; South Coast; Attainment Plan for 1997...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-09

...EPA is approving in part and disapproving in part state implementation plan (SIP) revisions submitted by California to provide for attainment of the 1997 fine particulate matter (PM2.5) national ambient air quality standards in the Los Angeles-South Coast area (South Coast). These SIP revisions are the South Coast 2007 Air Quality Management Plan (South Coast 2007 AQMP) (revised 2011) and South Coast-related provisions of the 2007 State Strategy (revised 2009 and 2011). EPA is approving the emissions inventory; reasonably available control measures/reasonably available control technology demonstration; the reasonable further progress and attainment demonstrations and associated air quality modeling; and the transportation conformity motor vehicle emissions budgets. EPA is also granting California's request to extend the attainment deadline for the South Coast to April 5, 2015 and approving commitments to measures and reductions by the South Coast Air Quality Management District and the California Air Resources Board. Finally, we are disapproving the SIP's contingency measures and issuing a protective finding under 40 CFR 93.120(a)(3), and we are rejecting the assignment of 10 tons per day (tpd) of nitrogen oxide (NOX) reductions to the federal government.

Control by quality: proposition of a typology.

PubMed

Pujo, P; Pillet, M

The application of Quality tools and methods in industrial management has always had a fundamental impact on the control of production. It influences the behavior of the actors concerned, while introducing the necessary notions and formalizations, especially for production systems with little or no automation, which constitute a large part of the industrial activity. Several quality approaches are applied in the workshop and are implemented at the level of the control. In this paper, the authors present a typology of the various approaches that have successively influenced control, such as statistical process control, quality assurance, and continuous improvement. First the authors present a parallel between production control and quality organizational structure. They note the duality between control, which is aimed at increasing productivity, and quality, which aims to satisfy the needs of the customer. They also note the hierarchical organizational structure of these two systems of management with, at each level, the notion of a feedback loop. This notion is fundamental to any kind of decision making. The paper is organized around the operational, tactical, and strategic levels, by describing for each level the main methods and tools for control by quality. The overview of these tools and methods starts at the operational level, with the Statistical Process Control, the Taguchi technique, and the "six sigma" approach. On the tactical level, we find a quality system approach, with a documented description of the procedures introduced in the firm. The management system can refer here to Quality Assurance, Total Productive Maintenance, or Management by Total Quality. The formalization through procedures of the rules of decision governing the process control enhances the validity of these rules. This leads to the enhancement of their reliability and to their consolidation. All this counterbalances the human, intrinsically fluctuating, behavior of the control operators. Strategic control by quality is then detailed, and the two main approaches, the continuous improvement approach and the proactive improvement approach, are introduced. Finally, the authors observe that at each of the three levels, the continuous process improvement, which is a component of Total Quality, becomes an essential preoccupation for the control. Ultimately, the recursive utilization of the Deming cycle remains the best practice for the control by quality.

The Global Streamflow Indices and Metadata Archive (GSIM) - Part 2: Quality control, time-series indices and homogeneity assessment

NASA Astrophysics Data System (ADS)

Gudmundsson, Lukas; Do, Hong Xuan; Leonard, Michael; Westra, Seth

2018-04-01

This is Part 2 of a two-paper series presenting the Global Streamflow Indices and Metadata Archive (GSIM), which is a collection of daily streamflow observations at more than 30 000 stations around the world. While Part 1 (Do et al., 2018a) describes the data collection process as well as the generation of auxiliary catchment data (e.g. catchment boundary, land cover, mean climate), Part 2 introduces a set of quality controlled time-series indices representing (i) the water balance, (ii) the seasonal cycle, (iii) low flows and (iv) floods. To this end we first consider the quality of individual daily records using a combination of quality flags from data providers and automated screening methods. Subsequently, streamflow time-series indices are computed for yearly, seasonal and monthly resolution. The paper provides a generalized assessment of the homogeneity of all generated streamflow time-series indices, which can be used to select time series that are suitable for a specific task. The newly generated global set of streamflow time-series indices is made freely available with an digital object identifier at https://doi.pangaea.de/10.1594/PANGAEA.887470 and is expected to foster global freshwater research, by acting as a ground truth for model validation or as a basis for assessing the role of human impacts on the terrestrial water cycle. It is hoped that a renewed interest in streamflow data at the global scale will foster efforts in the systematic assessment of data quality and provide momentum to overcome administrative barriers that lead to inconsistencies in global collections of relevant hydrological observations.

Guidelines for quality assurance and quality control of fish taxonomic data collected as part of the National Water-Quality Assessment Program

USGS Publications Warehouse

Walsh, Stephen Joseph; Meador, Michael R.

1998-01-01

Fish community structure is characterized by the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program as part of a perennial, multidisciplinary approach to evaluating the physical, chemical, and biological conditions of the Nation's water resources. The objective of quality assurance and quality control of fish taxonomic data that are collected as part of the NAWQA Program is to establish uniform guidelines and protocols for the identification, processing, and archiving of fish specimens to ensure that accurate and reliable data are collected. Study unit biologists, collaborating with regional biologists and fish taxonomic specialists, prepare a pre-sampling study plan that includes a preliminary faunal list and identification of an ichthyological curation center for receiving preserved fish specimens. Problematic taxonomic issues and protected taxa also are identified in the study plan, and collecting permits are obtained in advance of sampling activities. Taxonomic specialists are selected to identify fish specimens in the field and to assist in determining what fish specimens should be sacrificed, fixed, and preserved for laboratory identification, independent taxonomic verification, and long-term storage in reference or voucher collections. Quantitative and qualitative sampling of fishes follows standard methods previously established for the NAWQA Program. Common ichthyological techniques are used to process samples in the field and prepare fish specimens to be returned to the laboratory or sent to an institutional repository. Taxonomic identifications are reported by using a standardized list of scientific names that provides nomenclatural consistency and uniformity across study units.

40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

Code of Federal Regulations, 2012 CFR

2012-07-01

... Systems 1.2.1Calibration Error Test and Linearity Check Procedures Keep a written record of the procedures used for daily calibration error tests and linearity checks (e.g., how gases are to be injected..., and when calibration adjustments should be made). Identify any calibration error test and linearity...

40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

Code of Federal Regulations, 2013 CFR

2013-07-01

... Systems 1.2.1Calibration Error Test and Linearity Check Procedures Keep a written record of the procedures used for daily calibration error tests and linearity checks (e.g., how gases are to be injected..., and when calibration adjustments should be made). Identify any calibration error test and linearity...

76 FR 72626 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-25

.... (See section 307(b)(2).) List of Subjects in 40 CFR part 52 Environmental protection, Air pollution... Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the Control of Volatile Organic... accordance with the requirements of the Clean Air Act (CAA). DATES: Effective Date: This final rule is...

40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

Code of Federal Regulations, 2011 CFR

2011-07-01

... suitable for inspection. A maintenance log may be used for this purpose. The following records should be... the previous 26 unit (or stack) operating hours; and (b) the 26 clock hour data validation window for... official test log for each monitoring system. (i) The results of any certification, recertification...

DYNAMIC EVALUATION OF REGIONAL AIR QUALITY MODELS: ASSESSING CHANGES TO O 3 STEMMING FROM CHANGES IN EMISSIONS AND METEOROLOGY

EPA Science Inventory

Regional-scale air quality models are used to estimate the response of air pollutants to potential emission control strategies as part of the decision-making process. Traditionally, the model predicted pollutant concentrations are evaluated for the “base case” to assess a model’s...

Crisis Counseling for a Quality School Community: Applying William Glasser's Choice Therapy.

ERIC Educational Resources Information Center

Palmatier, Larry L., Ed.

This book draws upon William Glasser's choice theory, which categorically rejects external control psychology. Part I, "Seeing Crises in a Context," includes: (1) "Managing for Quality in the Schools" (W. Glasser); (2) "Reality Therapy and Choice Theory: Making Personal Choices for a Change" (L. L. Palmatier); (3)…

76 FR 14805 - Approval and Promulgation of Air Quality Implementation Plans; Virginia; Adoption of the Revised...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-18

... Promulgation of Air Quality Implementation Plans; Virginia; Adoption of the Revised Lead Standards and Related... SIP revisions add the primary and secondary lead standards of 0.15 micrograms per cubic meter ([mu]g... CFR Part 52 Environmental protection, Air pollution control, Incorporation by reference, Ozone...

Handling Qualities Prediction of an F-16XL-Based Reduced Sonic Boom Aircraft

NASA Technical Reports Server (NTRS)

Cogan, Bruce; Yoo, Seung

2010-01-01

A major goal of the Supersonics Project under NASA s Fundamental Aeronautics program is sonic boom reduction of supersonic aircraft. An important part of this effort is development and validation of sonic boom prediction tools used in aircraft design. NASA Dryden s F- 16XL was selected as a potential testbed aircraft to provide flight validation. Part of this task was predicting the handling qualities of the modified aircraft. Due to the high cost of modifying the existing F-16XL control laws, it was desirable to find modifications that reduced the aircraft sonic boom but did not degrade baseline aircraft handling qualities allowing for the potential of flight test without changing the current control laws. This was not a requirement for the initial modification design work, but an important consideration for proceeding to the flight test option. The primary objective of this work was to determine an aerodynamic and mass properties envelope of the F-16XL aircraft. The designers could use this envelope to determine the effect of proposed modifications on aircraft handling qualities.

Dimensional Metrology of Non-rigid Parts Without Specialized Inspection Fixtures =

NASA Astrophysics Data System (ADS)

Sabri, Vahid

Quality control is an important factor for manufacturing companies looking to prosper in an era of globalization, market pressures and technological advances. Functionality and product quality cannot be guaranteed without this important aspect. Manufactured parts have deviations from their nominal (CAD) shape caused by the manufacturing process. Thus, geometric inspection is a very important element in the quality control of mechanical parts. We will focus here on the geometric inspection of non-rigid (flexible) parts which are widely used in the aeronautic and automotive industries. Non-rigid parts can have different forms in a free-state condition compared with their nominal models due to residual stress and gravity loads. To solve this problem, dedicated inspection fixtures are generally used in industry to compensate for the displacement of such parts for simulating the use state in order to perform geometric inspections. These fixtures and the installation and inspection processes are expensive and time-consuming. Our aim in this thesis is therefore to develop an inspection method which eliminates the need for specialized fixtures. This is done by acquiring a point cloud from the part in a free-state condition using a contactless measuring device such as optical scanning and comparing it with the CAD model for the deviation identification. Using a non-rigid registration method and finite element analysis, we numerically inspect the profile of a non-rigid part. To do so, a simulated displacement is performed using an improved definition of displacement boundary conditions for simulating unfixed parts. In addition, we propose a numerical method for dimensional metrology of non-rigid parts in a free-state condition based on the arc length measurement by calculating the geodesic distance using the Fast Marching Method (FMM). In this thesis, we apply our developed methods on industrial non-rigid parts with free-form surfaces simulated with different types of displacement, defect, and measurement noise in order to evaluate the metrological performance of the developed methods.

Annual Report, Reservoir Control Center, Southwestern Division (1989)

DTIC Science & Technology

1990-01-01

Division in the water quality field . This provides for water quality objectives being included as an effective part of our total water management...WES) selected Canyon Lake as a research field site for developing techniques to evaluate the impacts associated with installation of hydropower at Corps...term continuous goals of this Division, and consequently the Water Management Branch, in the water quality field . (1) To obtain sufficient water

Quality of Working Life of Academics and Researchers in the UK: The Roles of Contract Type, Tenure and University Ranking

ERIC Educational Resources Information Center

Fontinha, Rita; Van Laar, Darren; Easton, Simon

2018-01-01

Quality of working life has been defined as the part of overall quality of life that is influenced by work. We developed a mediation model where home-work interface, job and career satisfaction, control at work, and working conditions are considered to be positively related to employee commitment and to the absence of stress at work. These two…

[Discussion on developing a data management plan and its key factors in clinical study based on electronic data capture system].

PubMed

Li, Qing-na; Huang, Xiu-ling; Gao, Rui; Lu, Fang

2012-08-01

Data management has significant impact on the quality control of clinical studies. Every clinical study should have a data management plan to provide overall work instructions and ensure that all of these tasks are completed according to the Good Clinical Data Management Practice (GCDMP). Meanwhile, the data management plan (DMP) is an auditable document requested by regulatory inspectors and must be written in a manner that is realistic and of high quality. The significance of DMP, the minimum standards and the best practices provided by GCDMP, the main contents of DMP based on electronic data capture (EDC) and some key factors of DMP influencing the quality of clinical study were elaborated in this paper. Specifically, DMP generally consists of 15 parts, namely, the approval page, the protocol summary, role and training, timelines, database design, creation, maintenance and security, data entry, data validation, quality control and quality assurance, the management of external data, serious adverse event data reconciliation, coding, database lock, data management reports, the communication plan and the abbreviated terms. Among them, the following three parts are regarded as the key factors: designing a standardized database of the clinical study, entering data in time and cleansing data efficiently. In the last part of this article, the authors also analyzed the problems in clinical research of traditional Chinese medicine using the EDC system and put forward some suggestions for improvement.

32 CFR Appendix A to Part 290 - DCAA's Organization and Mission

Code of Federal Regulations, 2010 CFR

2010-07-01

... established audit quality control standards, policies, and procedures and other internal control requirements... Information Service, 5285 Port Royal Road, Springfield, VA 22161. (c) Objective. Assist in achieving the... provides accounting and financial advisory service regarding contracts to all DoD components responsible...

75 FR 65292 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-22

... Officer for Agriculture, Office of Information and Regulatory Affairs, Office of Management and Budget... number. Food and Nutrition Service Title: Supplemental Nutrition Assistance Program Regulations, Part 275--Quality Control OMB Control Number: 0584-0303 Summary of Collection: Section 16 of the Food and Nutrition...

Constrained model predictive control, state estimation and coordination

NASA Astrophysics Data System (ADS)

Yan, Jun

In this dissertation, we study the interaction between the control performance and the quality of the state estimation in a constrained Model Predictive Control (MPC) framework for systems with stochastic disturbances. This consists of three parts: (i) the development of a constrained MPC formulation that adapts to the quality of the state estimation via constraints; (ii) the application of such a control law in a multi-vehicle formation coordinated control problem in which each vehicle operates subject to a no-collision constraint posed by others' imperfect prediction computed from finite bit-rate, communicated data; (iii) the design of the predictors and the communication resource assignment problem that satisfy the performance requirement from Part (ii). Model Predictive Control (MPC) is of interest because it is one of the few control design methods which preserves standard design variables and yet handles constraints. MPC is normally posed as a full-state feedback control and is implemented in a certainty-equivalence fashion with best estimates of the states being used in place of the exact state. However, if the state constraints were handled in the same certainty-equivalence fashion, the resulting control law could drive the real state to violate the constraints frequently. Part (i) focuses on exploring the inclusion of state estimates into the constraints. It does this by applying constrained MPC to a system with stochastic disturbances. The stochastic nature of the problem requires re-posing the constraints in a probabilistic form. In Part (ii), we consider applying constrained MPC as a local control law in a coordinated control problem of a group of distributed autonomous systems. Interactions between the systems are captured via constraints. First, we inspect the application of constrained MPC to a completely deterministic case. Formation stability theorems are derived for the subsystems and conditions on the local constraint set are derived in order to guarantee local stability or convergence to a target state. If these conditions are met for all subsystems, then this stability is inherited by the overall system. For the case when each subsystem suffers from disturbances in the dynamics, own self-measurement noises, and quantization errors on neighbors' information due to the finite-bit-rate channels, the constrained MPC strategy developed in Part (i) is appropriate to apply. In Part (iii), we discuss the local predictor design and bandwidth assignment problem in a coordinated vehicle formation context. The MPC controller used in Part (ii) relates the formation control performance and the information quality in the way that large standoff implies conservative performance. We first develop an LMI (Linear Matrix Inequality) formulation for cross-estimator design in a simple two-vehicle scenario with non-standard information: one vehicle does not have access to the other's exact control value applied at each sampling time, but to its known, pre-computed, coupling linear feedback control law. Then a similar LMI problem is formulated for the bandwidth assignment problem that minimizes the total number of bits by adjusting the prediction gain matrices and the number of bits assigned to each variable. (Abstract shortened by UMI.)

Evidence for the impact of quality improvement collaboratives: systematic review

PubMed Central

2008-01-01

Objective To evaluate the effectiveness of quality improvement collaboratives in improving the quality of care. Data sources Relevant studies through Medline, Embase, PsycINFO, CINAHL, and Cochrane databases. Study selection Two reviewers independently extracted data on topics, participants, setting, study design, and outcomes. Data synthesis Of 1104 articles identified, 72 were included in the study. Twelve reports representing nine studies (including two randomised controlled trials) used a controlled design to measure the effects of the quality improvement collaborative intervention on care processes or outcomes of care. Systematic review of these nine studies showed moderate positive results. Seven studies (including one randomised controlled trial) reported an effect on some of the selected outcome measures. Two studies (including one randomised controlled trial) did not show any significant effect. Conclusions The evidence underlying quality improvement collaboratives is positive but limited and the effects cannot be predicted with great certainty. Considering that quality improvement collaboratives seem to play a key part in current strategies focused on accelerating improvement, but may have only modest effects on outcomes at best, further knowledge of the basic components effectiveness, cost effectiveness, and success factors is crucial to determine the value of quality improvement collaboratives. PMID:18577559

7 CFR 982.57 - Exemptions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... as do not interfere with the volume and quality control objectives of this part, and shall require... handled or used only as authorized. (b) Sales by growers direct to consumers. Any hazelnut grower may sell.... Mail order sales are not exempt sales under this part. [51 FR 29549, Aug. 19, 1986, as amended at 61 FR...

Inorganic Analysis in Water Quality Control Programs. Instructor's Guide.

ERIC Educational Resources Information Center

Kroner, Audrey

This two-part instructor's guide was designed for a five-day course for chemists and technicians with little or no experience in inorganic analyses. Part I provides information on course planning and management including course description, staff responsibilities, suggested course plan and agenda, timeline for planning and conducting the course,…

78 FR 59258 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Withdrawal of Direct...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-26

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R03-OAR-2013-0058; FR-9901-21-Region3... Maintenance Area AGENCY: Environmental Protection Agency (EPA). ACTION: Withdrawal of direct final rule... Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Incorporation by reference...

The quantitative control and matching of an optical false color composite imaging system

NASA Astrophysics Data System (ADS)

Zhou, Chengxian; Dai, Zixin; Pan, Xizhe; Li, Yinxi

1993-10-01

Design of an imaging system for optical false color composite (OFCC) capable of high-precision density-exposure time control and color balance is presented. The system provides high quality FCC image data that can be analyzed using a quantitative calculation method. The quality requirement to each part of the image generation system is defined, and the distribution of satellite remote sensing image information is analyzed. The proposed technology makes it possible to present the remote sensing image data more effectively and accurately.

40 CFR 63.820 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

... were caused by a sudden, infrequent, and unavoidable failure of air pollution control and monitoring... activity or event that could have been foreseen and avoided, or planned for; and were not part of a... ambient air quality, the environment, and human health; (vi) All emissions monitoring and control systems...

40 CFR 63.820 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... were caused by a sudden, infrequent, and unavoidable failure of air pollution control and monitoring... activity or event that could have been foreseen and avoided, or planned for; and were not part of a... ambient air quality, the environment, and human health; (vi) All emissions monitoring and control systems...

40 CFR 63.820 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... were caused by a sudden, infrequent, and unavoidable failure of air pollution control and monitoring... activity or event that could have been foreseen and avoided, or planned for; and were not part of a... ambient air quality, the environment, and human health; (vi) All emissions monitoring and control systems...

[Current situation of health surveys in Spain].

PubMed

Requena, María Luisa; Suárez, Mónica; Pérez, Óscar

2013-01-01

To describe the evolution of health interview surveys in Spain (as of 01/01/2012), whether national or regional, its main characteristics and methodology, and in the case of general health surveys (GHIS), its contents. An adapted version of Eurostat quality control template European Health Interview Survey Technical and Methodological Report was filled in by those responsible for GHIS in each region (autonomous communities) and at the national level. The first part (11 questions) gathers general information about health surveys, both GHIS and surveys targeted to specific populations or health problems (SHIS). The second part (109 questions) asks about methodological characteristics of most recent GHIS. 1) regional or supra-regional scope; 2) for the second part, GHIS currently active series. Quality control was performed using double data entry and validated by informants.100 HIS were identified. 16 were GHIS and 84 SHIS. 32 (38%) of the latter were national and 52 (62%) regional. Nutrition 21 (25%), drug use 10 (12%), opinion polls 7 (9%) and dental health 7 (9%) were the most frequent topics in SHIS. Highest GHIS density was reached after year 2000, with several surveys on field at a time (mode=3). 11 GHIS (2 national, 9 regional) met inclusion criteria for the second part. All complied with general quality benchmarks. Few differences were observed in content.GHIS show more similarities than differences in objectives, methods and content. Rationalization and harmonization are needed. Physical activity, alcohol consumption, quality of life and mental health instruments are not yet consensual. Valid and comparable data are required on health status and its determinants to inform health policy.

Quality assurance and control in the production and static tests of the solid rocket boosters for the Space Shuttle

NASA Technical Reports Server (NTRS)

Cerny, O. F.

1979-01-01

The paper surveys the various aspects of design and overhaul of the solid rocket boosters. It is noted that quality control is an integral part of the design specifications. Attention is given to the production process which is optimized towards highest quality. Also discussed is the role of the DCA (Defense Contract Administration) in inspecting the products of subcontractors, noting that the USAF performs this role for prime contractors. Fabrication and construction of the booster is detailed with attention given to the lining of the booster cylinder and the mixing of the propellant and the subsequent X-ray inspection.

Manufacture and quality control of interconnecting wire hardnesses, Volume 1

NASA Technical Reports Server (NTRS)

1972-01-01

A standard is presented for manufacture, installation, and quality control of eight types of interconnecting wire harnesses. The processes, process controls, and inspection and test requirements reflected are based on acknowledgment of harness design requirements, acknowledgment of harness installation requirements, identification of the various parts, materials, etc., utilized in harness manufacture, and formulation of a typical manufacturing flow diagram for identification of each manufacturing and quality control process, operation, inspection, and test. The document covers interconnecting wire harnesses defined in the design standard, including type 1, enclosed in fluorocarbon elastomer convolute, tubing; type 2, enclosed in TFE convolute tubing lines with fiberglass braid; type 3, enclosed in TFE convolute tubing; and type 5, combination of types 3 and 4. Knowledge gained through experience on the Saturn 5 program coupled with recent advances in techniques, materials, and processes was incorporated.

Groundwater-quality data from the National Water-Quality Assessment Project, January through December 2014 and select quality-control data from May 2012 through December 2014

USGS Publications Warehouse

Arnold, Terri L.; Bexfield, Laura M.; Musgrove, MaryLynn; Lindsey, Bruce D.; Stackelberg, Paul E.; Barlow, Jeannie R.; Desimone, Leslie A.; Kulongoski, Justin T.; Kingsbury, James A.; Ayotte, Joseph D.; Fleming, Brandon J.; Belitz, Kenneth

2017-10-05

Groundwater-quality data were collected from 559 wells as part of the National Water-Quality Assessment Project of the U.S. Geological Survey National Water-Quality Program from January through December 2014. The data were collected from four types of well networks: principal aquifer study networks, which are used to assess the quality of groundwater used for public water supply; land-use study networks, which are used to assess land-use effects on shallow groundwater quality; major aquifer study networks, which are used to assess the quality of groundwater used for domestic supply; and enhanced trends networks, which are used to evaluate the time scales during which groundwater quality changes. Groundwater samples were analyzed for a large number of water-quality indicators and constituents, including major ions, nutrients, trace elements, volatile organic compounds, pesticides, radionuclides, and some constituents of special interest (arsenic speciation, chromium [VI] and perchlorate). These groundwater-quality data, along with data from quality-control samples, are tabulated in this report and in an associated data release.

Single-Family Quality Control Inspector Job Task Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Head, Heather R; Kurnik, Charles W

The National Renewable Energy Laboratory (NREL) is contracted by the U.S. Department of Energy (DOE) Weatherization Assistance Program (WAP) to develop and maintain the resources under the Guidelines for Home Energy Professionals (GHEP) project. As part of the GHEP strategy to increase the quality of work conducted for single-family, residential energy-efficiency retrofits, the Home Energy Professionals Job Task Analysis are used as the foundation for quality training programs and trainers.

Quality in the Basic Grant Delivery System: Volume 2, Corrective Actions.

ERIC Educational Resources Information Center

Advanced Technology, Inc., McLean, VA.

Alternative management procedures are recommended that may lower the rate and magnitude of errors in the award of the Basic Educational Opportunity Grants (BEOGs), or Pell Grants. The recommendations are part of the BEOG quality control project and are based on a review of current (1980-1981) levels, distribution, and significance of error in the…

Consequences of Part Temperature Variability in Electron Beam Melting of Ti-6Al-4V

NASA Astrophysics Data System (ADS)

Fisher, Brian A.; Mireles, Jorge; Ridwan, Shakerur; Wicker, Ryan B.; Beuth, Jack

2017-12-01

To facilitate adoption of Ti-6Al-4V (Ti64) parts produced via additive manufacturing (AM), the ability to ensure part quality is critical. Measuring temperatures is an important component of part quality monitoring in all direct metal AM processes. In this work, surface temperatures were monitored using a custom infrared camera system attached to an Arcam electron beam melting (EBM®) machine. These temperatures were analyzed to understand their possible effect on solidification microstructure based on solidification cooling rates extracted from finite element simulations. Complicated thermal histories were seen during part builds, and temperature changes occurring during typical Ti64 builds may be large enough to affect solidification microstructure. There is, however, enough time between fusion of individual layers for spatial temperature variations (i.e., hot spots) to dissipate. This means that an effective thermal control strategy for EBM® can be based on average measured surface temperatures, ignoring temperature variability.

Effect of IN718 Recycled Powder Reuse on Properties of Parts Manufactured by Means of Selective Laser Melting

NASA Astrophysics Data System (ADS)

Ardila, L. C.; Garciandia, F.; González-Díaz, J. B.; Álvarez, P.; Echeverria, A.; Petite, M. M.; Deffley, R.; Ochoa, J.

Powder quality control is essential to obtain parts with suitable mechanical properties in Selective Laser Melting manufacturing technique. One of the most important advantages of suchtechnique is that it allows an efficient use of the material, due to the possibility to recycle and reuse un-melted powder. Nevertheless, powder material properties may change due to repeated recycling, affecting this way the mechanicalbehavior of parts. In this paper the effect of powder reuse on its quality and on the mechanical properties of the resulting melted parts is studied via self-developed recycling methodology. The material considered for investigation was IN718, a nickel superalloy widely used in industry. After recycling powder up to 14 times, no significant changes were observed in powder and test parts properties. The results obtained in this work will help to validate powder recycling methodology for its use in current industrial Selective Laser Melting manufacturing.

Some Improvements in H-PDLCs

NASA Technical Reports Server (NTRS)

Crawford, Gregory P.; Li, Liuliu

2005-01-01

Some improvements have been made in the formulation of holographically formed polymer-dispersed liquid crystals (H-PDLCs) and in the fabrication of devices made from these materials, with resulting improvements in performance. H-PDLCs are essentially volume Bragg gratings. Devices made from H-PDLCs function as electrically switchable reflective filters. Heretofore, it has been necessary to apply undesirably high drive voltages in order to switch H-PDLC devices. Many scientific papers on H-PDLCs and on the potential utility of H-PDLC devices for display and telecommunication applications have been published. However, until now, little has been published about improving quality control in synthesis of H-PDLCs and fabrication of H-PDLC devices to minimize (1) spatial nonuniformities within individual devices, (2) nonuniformities among nominally identical devices, and (3) variations in performance among nominally identical devices. The improvements reported here are results of a research effort directed partly toward solving these quality-control problems and partly toward reducing switching voltages. The quality-control improvements include incorporation of a number of process controls to create a relatively robust process, such that the H-PDLC devices fabricated in this process are more nearly uniform than were those fabricated in a prior laboratory-type process. The improved process includes ultrasonic mixing, ultrasonic cleaning, the use of a micro dispensing technique, and the use of a bubble press.

Evaluation of quality of life and sexual functioning of women using levonorgestrel-releasing intrauterine contraceptive system--Mirena.

PubMed

Skrzypulec, Violetta; Drosdzol, Agnieszka

2008-12-01

The advantages ensuing from the high contraceptive efficacy, positive effect on the parameters of the menstrual cycle as well as other values of the levonorgestrel-releasing intrauterine system may play an important role in women's sexual life. The aim of the study was to evaluate the effect of the levonorgestrel-releasing intrauterine system on the quality of life and sexual functioning of women. The research encompassed 200 women aged between 30 and 45. 52 women using the levonorgestrel-releasing intrauterine system were qualified to the study as the research group (Mirena Group). The control groups consisted of 48 women using a different type of intrauterine device (Control Group I--Other IUD) and 50 women using no contraception (Control Group II). A specific questionnaire with a general part concerning socio-demographic conditions, a part dealing with contraception and Polish version of self-evaluation inventories: Short Form-36 Health Survey, Female Sexual Function Index and Mell-Krat Scale was used as a research tool. Quality of life parameters for women using the Mirena system were higher than for the control groups, especially in the aspect of general health, energy/fatigue and emotional well-being. A significant beneficial effect of the levonorgestrel-releasing intrauterine system on sexual functioning (sexual desire and arousal) was also revealed in the study. Sexual dysfunctions were diagnosed in 20.8% of Other IUD, 34.7% of Control Group II and 9.6% of Mirena Group. Levonorgestrel-releasing intrauterine system increases female quality of life and sexual functioning parameters.

Quality control analysis : part V : review of data generated by statistical specifications on asphaltic concrete : final report.

DOT National Transportation Integrated Search

1975-12-01

The primary objective of this study was to review the data generated by projects governed by statistically oriented system of specifications for the control and acceptance of asphaltic concrete and to recommend any revisions that may be deemed necess...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

76 FR 51314 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Adoption of Drum and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-18

... Miscellaneous Metal and Plastic Parts Coatings and will help Maryland attain and maintain the National Ambient... adoption of the drum and pail coating standards found in the Miscellaneous Metal and Plastic Parts Coatings... the area's date of attainment. CTGs are intended to provide state and local air pollution control...

76 FR 64015 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-17

... miscellaneous metal and plastic products in 1978, which includes drum and pail coating, and revised them in 2008... drum and pail coatings, part of the EPA miscellaneous metal and plastic parts coatings CTG. EPA...); Does not impose an information collection burden under the provisions of the Paperwork Reduction Act...

An efficient visualization method for analyzing biometric data

NASA Astrophysics Data System (ADS)

Rahmes, Mark; McGonagle, Mike; Yates, J. Harlan; Henning, Ronda; Hackett, Jay

2013-05-01

We introduce a novel application for biometric data analysis. This technology can be used as part of a unique and systematic approach designed to augment existing processing chains. Our system provides image quality control and analysis capabilities. We show how analysis and efficient visualization are used as part of an automated process. The goal of this system is to provide a unified platform for the analysis of biometric images that reduce manual effort and increase the likelihood of a match being brought to an examiner's attention from either a manual or lights-out application. We discuss the functionality of FeatureSCOPE™ which provides an efficient tool for feature analysis and quality control of biometric extracted features. Biometric databases must be checked for accuracy for a large volume of data attributes. Our solution accelerates review of features by a factor of up to 100 times. Review of qualitative results and cost reduction is shown by using efficient parallel visual review for quality control. Our process automatically sorts and filters features for examination, and packs these into a condensed view. An analyst can then rapidly page through screens of features and flag and annotate outliers as necessary.

Flight Measurements of the Flying Qualities of a Lockheed P-80A Airplane (Army No. 44-85099): Lateral- and Directional-Stability and Control Characteristics

NASA Technical Reports Server (NTRS)

Anderson, Seth B.; Cooper, George E.

1947-01-01

This report contains the flight-test results of the lateral and directional-stability and control phase (including tests with wing-tip tanks) of a general flying-qualities investigation of the Lockheed P-80A airplane (Army No. 44-85099). These tests were conducted at indicated airspeeds up to 494 miles per hour (0.691 Mach number) at low altitude and up to 378 miles per hour (0.816 Mach number) at high altitude. These tests showed that the flying qualities of the airplane were for the most part in accordance with the requirements of the Army Air Forces Stability and Control Specifications. The only major deficiency noted was the negative lateral stability with the wing-tip tanks installed.

The effect of laser focus and process parameters on microstructure and mechanical properties of SLM Inconel 718

NASA Astrophysics Data System (ADS)

Bean, Glenn E.; Witkin, David B.; McLouth, Tait D.; Zaldivar, Rafael J.

2018-02-01

Research on the selective laser melting (SLM) method of laser powder bed fusion additive manufacturing (AM) has shown that surface and internal quality of AM parts is directly related to machine settings such as laser energy density, scanning strategies, and atmosphere. To optimize laser parameters for improved component quality, the energy density is typically controlled via laser power, scanning rate, and scanning strategy, but can also be controlled by changing the spot size via laser focal plane shift. Present work being conducted by The Aerospace Corporation was initiated after observing inconsistent build quality of parts printed using OEM-installed settings. Initial builds of Inconel 718 witness geometries using OEM laser parameters were evaluated for surface roughness, density, and porosity while varying energy density via laser focus shift. Based on these results, hardware and laser parameter adjustments were conducted in order to improve build quality and consistency. Tensile testing was also conducted to investigate the effect of build plate location and laser settings on SLM 718. This work has provided insight into the limitations of OEM parameters compared with optimized parameters towards the goal of manufacturing aerospace-grade parts, and has led to the development of a methodology for laser parameter tuning that can be applied to other alloy systems. Additionally, evidence was found that for 718, which derives its strength from post-manufacturing heat treatment, there is a possibility that tensile testing may not be perceptive to defects which would reduce component performance. Ongoing research is being conducted towards identifying appropriate testing and analysis methods for screening and quality assurance.

Design and Implementation of Total Quality Management in a Civil Engineering Squadron

DTIC Science & Technology

1989-09-01

instruct employees and seek new ways to integrate quality into all functions, such as planning, marketing , and controlling. The second strategy is for...implement a TQM plan that contributes to the overall DOD TQM process. 7 2. Managers at all levels will provide leadership and integrate TQM principles... integral part of our daily activities. 8 3. Quality improvement is the key to productivity improvement and must be pursued with the necessary resources to

Factors controlling groundwater quality in the Yeonjegu District of Busan City, Korea, using the hydrogeochemical processes and fuzzy GIS.

PubMed

Venkatramanan, Senapathi; Chung, Sang Yong; Selvam, Sekar; Lee, Seung Yeop; Elzain, Hussam Eldin

2017-10-01

The hydrogeochemical processes and fuzzy GIS techniques were used to evaluate the groundwater quality in the Yeonjegu district of Busan Metropolitan City, Korea. The highest concentrations of major ions were mainly related to the local geology. The seawater intrusion into the river water and municipal contaminants were secondary contamination sources of groundwater in the study area. Factor analysis represented the contamination sources of the mineral dissolution of the host rocks and domestic influences. The Gibbs plot exhibited that the major ions were derived from the rock weathering condition. Piper's trilinear diagram showed that the groundwater quality was classified into five types of CaHCO 3 , NaHCO 3 , NaCl, CaCl 2 , and CaSO 4 types in that order. The ionic relationship and the saturation mineral index of the ions indicated that the evaporation, dissolution, and precipitation processes controlled the groundwater chemistry. The fuzzy GIS map showed that highly contaminated groundwater occurred in the northeastern and the central parts and that the groundwater of medium quality appeared in most parts of the study area. It suggested that the groundwater quality of the study area was influenced by local geology, seawater intrusion, and municipal contaminants. This research clearly demonstrated that the geochemical analyses and fuzzy GIS method were very useful to identify the contaminant sources and the location of good groundwater quality.

Predicting quality of life in pediatric asthma: the role of emotional competence and personality.

PubMed

Lahaye, Magali; Van Broeck, Nady; Bodart, Eddy; Luminet, Olivier

2013-05-01

The present study examined the predictive value of emotional competence and the five-factor model of personality on the quality of life of children with asthma. Participants were 90 children (M age = 11.73, SD = 2.60) having controlled and partly controlled asthma, undergoing everyday treatment. Children filled in questionnaires assessing emotional competence and quality of life. Parents completed questionnaires assessing the personality of their child. Results showed that two emotional competences, bodily awareness and verbal sharing of emotions, were related to the quality of life of children with asthma. Moreover, one personality trait, benevolence, was associated with children's quality of life. Regression analyses showed that the predictive value of these three dimensions remained significant over and above asthma control and socio-demographic variables frequently associated with the quality of life of children with asthma (age, gender, and educational level of parents). These findings emphasize the importance of alerting the clinician who works with children with asthma to observe and assess the child's expression of emotions, attention to bodily sensations, and benevolence.

40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

Code of Federal Regulations, 2010 CFR

2010-07-01

... in section 2.3 of this appendix and the Hg emission tests described in §§ 75.81(c) and 75.81(d)(4). 1.2Specific Requirements for Continuous Emissions Monitoring Systems 1.2.1Calibration Error Test and Linearity Check Procedures Keep a written record of the procedures used for daily calibration error tests and...

The NCC project: A quality management perspective

NASA Technical Reports Server (NTRS)

Lee, Raymond H.

1993-01-01

The Network Control Center (NCC) Project introduced the concept of total quality management (TQM) in mid-1990. The CSC project team established a program which focused on continuous process improvement in software development methodology and consistent deliveries of high quality software products for the NCC. The vision of the TQM program was to produce error free software. Specific goals were established to allow continuing assessment of the progress toward meeting the overall quality objectives. The total quality environment, now a part of the NCC Project culture, has become the foundation for continuous process improvement and has resulted in the consistent delivery of quality software products over the last three years.

Advanced manufacturing development of a composite empennage component for L-1011 aircraft

NASA Technical Reports Server (NTRS)

Alva, T.; Henkel, J.; Johnson, R.; Carll, B.; Jackson, A.; Mosesian, B.; Brozovic, R.; Obrien, R.; Eudaily, R.

1982-01-01

This is the final report of technical work conducted during the fourth phase of a multiphase program having the objective of the design, development and flight evaluation of an advanced composite empennage component manufactured in a production environment at a cost competitive with those of its metal counterpart, and at a weight savings of at least 20 percent. The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes front and rear spars. During Phase 4 of the program, production quality tooling was designed and manufactured to produce three sets of covers, ribs, spars, miscellaneous parts, and subassemblies to assemble three complete ACVF units. Recurring and nonrecurring cost data were compiled and documented in the updated producibility/design to cost plan. Nondestruct inspections, quality control tests, and quality acceptance tests were performed in accordance with the quality assurance plan and the structural integrity control plan. Records were maintained to provide traceability of material and parts throughout the manufacturing development phase. It was also determined that additional tooling would not be required to support the current and projected L-1011 production rate.

An integrated toolbox for processing and analysis of remote sensing data of inland and coastal waters - atmospheric correction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haan, J.F. de; Kokke, J.M.M.; Hoogenboom, H.J.

1997-06-01

Deriving thematic maps of water quality parameters from a remote sensing image requires a number of processing steps, such as calibration, atmospheric correction, air-water interface correction, and application of water quality algorithms. A prototype version of an integrated software environment has recently been developed that enables the user to perform and control these processing steps. Major parts of this environment are: (i) access to the MODTRAN 3 radiative transfer code, (ii) a database of water quality algorithms, and (iii) a spectral library of Dutch coastal and inland waters, containing subsurface irradiance reflectance spectra and associated water quality parameters. The atmosphericmore » correction part of this environment is discussed here. It is shown that this part can be used to accurately retrieve spectral signatures of inland water for wavelengths between 450 and 750 nm, provided in situ measurements are used to determine atmospheric model parameters. Assessment of the usefulness of the completely integrated software system in an operational environment requires a revised version that is presently being developed.« less

Controlling Nonpoint-Source Water Pollution: A Citizen's Handbook.

ERIC Educational Resources Information Center

Hansen, Nancy Richardson; And Others

Citizens can play an important role in helping their states develop pollution control programs and spurring effective efforts to deal with nonpoint-source pollution. This guide takes the reader step-by-step through the process that states must follow to comply with water quality legislation relevant to nonpoint-source pollution. Part I provides…

40 CFR 52.74 - Original identification of plan section.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Governor of Alaska on January 18, 1980 as follows: Volume II. Analysis of Problems, Control Actions Section... requirements of Air Quality Monitoring, 40 CFR part 58, subpart C, § 58.20, as follows: Volume II. Analysis of Problems, Control Actions Section V. Ambient Air Monitoring A. Purpose C. Air Monitoring Network E. Annual...

40 CFR 52.70 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... submitted by the Governor of Alaska on January 18, 1980 as follows: Volume II. Analysis of Problems, Control... requirements of Air Quality Monitoring, 40 CFR part 58, subpart C, § 58.20, as follows: Volume II. Analysis of Problems, Control Actions Section V. Ambient Air Monitoring A. Purpose C. Air Monitoring Network E. Annual...

77 FR 39943 - Approval and Promulgation of Air Quality Implementation Plans; Illinois; Regional Haze

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-06

... contingent on the Cross-State Air Pollution Rule (CSAPR) and thus is not affected by the stay of that rule...)(2).) List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control..., Subtitle B: Air Pollution, Chapter 1: Pollution Control Board, Subchapter c: Emission Standards and...

40 CFR 52.246 - Control of dry cleaning solvent vapor losses.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Joaquin Valley Intrastate Air Quality Control Regions (the “Regions”), as described in 40 CFR part 81, dated July 1, 1979, except as follows: (1) In the following portions of the Sacramento Valley Region... Basin portion). (iii) Yuba County APCD. (iv) Sutter County APCD. (2) In the following portions of the...

40 CFR 52.246 - Control of dry cleaning solvent vapor losses.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Joaquin Valley Intrastate Air Quality Control Regions (the “Regions”), as described in 40 CFR part 81, dated July 1, 1979, except as follows: (1) In the following portions of the Sacramento Valley Region... Basin portion). (iii) Yuba County APCD. (iv) Sutter County APCD. (2) In the following portions of the...

40 CFR 52.246 - Control of dry cleaning solvent vapor losses.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Joaquin Valley Intrastate Air Quality Control Regions (the “Regions”), as described in 40 CFR part 81, dated July 1, 1979, except as follows: (1) In the following portions of the Sacramento Valley Region... Basin portion). (iii) Yuba County APCD. (iv) Sutter County APCD. (2) In the following portions of the...

40 CFR 52.246 - Control of dry cleaning solvent vapor losses.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Joaquin Valley Intrastate Air Quality Control Regions (the “Regions”), as described in 40 CFR part 81, dated July 1, 1979, except as follows: (1) In the following portions of the Sacramento Valley Region... Basin portion). (iii) Yuba County APCD. (iv) Sutter County APCD. (2) In the following portions of the...

Moving from Control to Culture in Higher Education Quality

NASA Astrophysics Data System (ADS)

Ehlers, Ulf-Daniel

In this article, it is argued that quality development in higher education needs to go beyond the implementation of rules and processes for quality management purposes to improve the educational quality. Quality development has to rather focus on promoting a quality culture, which enables individual actors to continuously improve their profession. While this understanding of quality as part of the organizational culture gains more importance, there is still a lack of fundamental research and conceptual understanding of the phenomenon in itself. This article aims to lay the foundations for a comprehensive understanding of quality culture in organizations focusing on higher education. For this purpose, the state of the art in research on organizational culture is discussed and a model of quality culture is presented.

1990 National Water Quality Laboratory Services Catalog

USGS Publications Warehouse

Pritt, Jeffrey; Jones, Berwyn E.

1989-01-01

PREFACE This catalog provides information about analytical services available from the National Water Quality Laboratory (NWQL) to support programs of the Water Resources Division of the U.S. Geological Survey. To assist personnel in the selection of analytical services, the catalog lists cost, sample volume, applicable concentration range, detection level, precision of analysis, and preservation techniques for samples to be submitted for analysis. Prices for services reflect operationa1 costs, the complexity of each analytical procedure, and the costs to ensure analytical quality control. The catalog consists of five parts. Part 1 is a glossary of terminology; Part 2 lists the bottles, containers, solutions, and other materials that are available through the NWQL; Part 3 describes the field processing of samples to be submitted for analysis; Part 4 describes analytical services that are available; and Part 5 contains indices of analytical methodology and Chemical Abstract Services (CAS) numbers. Nomenclature used in the catalog is consistent with WATSTORE and STORET. The user is provided with laboratory codes and schedules that consist of groupings of parameters which are measured together in the NWQL. In cases where more than one analytical range is offered for a single element or compound, different laboratory codes are given. Book 5 of the series 'Techniques of Water Resources Investigations of the U.S. Geological Survey' should be consulted for more information about the analytical procedures included in the tabulations. This catalog supersedes U.S. Geological Survey Open-File Report 86-232 '1986-87-88 National Water Quality Laboratory Services Catalog', October 1985.

A bill to amend the Energy Employees Occupational Illness Compensation Program Act of 2000 to strengthen the quality control measures in place for part B lung disease claims and part E processes with independent reviews.

THOMAS, 112th Congress

Sen. Udall, Mark [D-CO

2011-03-10

Senate - 03/10/2011 Read twice and referred to the Committee on Health, Education, Labor, and Pensions. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

Process development for green part printing using binder jetting additive manufacturing

NASA Astrophysics Data System (ADS)

Miyanaji, Hadi; Orth, Morgan; Akbar, Junaid Muhammad; Yang, Li

2018-05-01

Originally developed decades ago, the binder jetting additive manufacturing (BJ-AM) process possesses various advantages compared to other additive manufacturing (AM) technologies such as broad material compatibility and technological expandability. However, the adoption of BJ-AM has been limited by the lack of knowledge with the fundamental understanding of the process principles and characteristics, as well as the relatively few systematic design guideline that are available. In this work, the process design considerations for BJ-AM in green part fabrication were discussed in detail in order to provide a comprehensive perspective of the design for additive manufacturing for the process. Various process factors, including binder saturation, in-process drying, powder spreading, powder feedstock characteristics, binder characteristics and post-process curing, could significantly affect the printing quality of the green parts such as geometrical accuracy and part integrity. For powder feedstock with low flowability, even though process parameters could be optimized to partially offset the printing feasibility issue, the qualities of the green parts will be intrinsically limited due to the existence of large internal voids that are inaccessible to the binder. In addition, during the process development, the balanced combination between the saturation level and in-process drying is of critical importance in the quality control of the green parts.

Systematic review of the effects of chronic disease management on quality-of-life in people with chronic obstructive pulmonary disease.

PubMed

Niesink, A; Trappenburg, J C A; de Weert-van Oene, G H; Lammers, J W J; Verheij, T J M; Schrijvers, A J P

2007-11-01

Chronic disease management for patients with chronic obstructive pulmonary disease (COPD) may improve quality, outcomes and access to care. To investigate effectiveness of chronic disease management programmes on the quality-of-life of people with COPD. Medline and Embase (1995-2005) were searched for relevant articles, and reference lists and abstracts were searched for controlled trials of chronic disease management programmes for patients with COPD. Quality-of-life was assessed as an outcome parameter. Two reviewers independently reviewed each paper for methodological quality and extracted the data. We found 10 randomized-controlled trials comparing chronic disease management with routine care. Patient populations, health-care professionals, intensity, and content of the intervention were heterogeneous. Different instruments were used to assess quality of life. Five out of 10 studies showed statistically significant positive outcomes on one or more domains of the quality of life instruments. Three studies, partly located in primary care, showed positive results. All chronic disease management projects for people with COPD involving primary care improved quality of life. In most of the studies, aspects of chronic disease management were applied to a limited extent. Quality of randomized-controlled trials was not optimal. More research is needed on chronic disease management programmes in patients with COPD across primary and secondary care.

Quality assurance of the international computerised 24 h dietary recall method (EPIC-Soft).

PubMed

Crispim, Sandra P; Nicolas, Genevieve; Casagrande, Corinne; Knaze, Viktoria; Illner, Anne-Kathrin; Huybrechts, Inge; Slimani, Nadia

2014-02-01

The interview-administered 24 h dietary recall (24-HDR) EPIC-Soft® has a series of controls to guarantee the quality of dietary data across countries. These comprise all steps that are part of fieldwork preparation, data collection and data management; however, a complete characterisation of these quality controls is still lacking. The present paper describes in detail the quality controls applied in EPIC-Soft, which are, to a large extent, built on the basis of the EPIC-Soft error model and are present in three phases: (1) before, (2) during and (3) after the 24-HDR interviews. Quality controls for consistency and harmonisation are implemented before the interviews while preparing the seventy databases constituting an EPIC-Soft version (e.g. pre-defined and coded foods and recipes). During the interviews, EPIC-Soft uses a cognitive approach by helping the respondent to recall the dietary intake information in a stepwise manner and includes controls for consistency (e.g. probing questions) as well as for completeness of the collected data (e.g. system calculation for some unknown amounts). After the interviews, a series of controls can be applied by dietitians and data managers to further guarantee data quality. For example, the interview-specific 'note files' that were created to track any problems or missing information during the interviews can be checked to clarify the information initially provided. Overall, the quality controls employed in the EPIC-Soft methodology are not always perceivable, but prove to be of assistance for its overall standardisation and possibly for the accuracy of the collected data.

Quality control analysis : part I : asphaltic concrete.

DOT National Transportation Integrated Search

1964-11-01

This report deals with the statistical evaluation of results from several hot mix plants to determine the pattern of variability with respect to bituminous hot mix characteristics. : Individual tests results when subjected to frequency distribution i...

Quality control algorithms for rainfall measurements

NASA Astrophysics Data System (ADS)

Golz, Claudia; Einfalt, Thomas; Gabella, Marco; Germann, Urs

2005-09-01

One of the basic requirements for a scientific use of rain data from raingauges, ground and space radars is data quality control. Rain data could be used more intensively in many fields of activity (meteorology, hydrology, etc.), if the achievable data quality could be improved. This depends on the available data quality delivered by the measuring devices and the data quality enhancement procedures. To get an overview of the existing algorithms a literature review and literature pool have been produced. The diverse algorithms have been evaluated to meet VOLTAIRE objectives and sorted in different groups. To test the chosen algorithms an algorithm pool has been established, where the software is collected. A large part of this work presented here is implemented in the scope of the EU-project VOLTAIRE ( Validati on of mu ltisensors precipit ation fields and numerical modeling in Mediter ran ean test sites).

Inferential control -- Part 1: Crude unit advanced controls pass accuracy and repeatability tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

San, Y.P.; Landells, K.C.; Mackay, D.C.

1994-11-28

An inferential model is one that provides a quality for which an analyzer is not available. This type of model uses readily available physical measurements -- such as temperatures, pressures, and flow rates -- to infer a quality such as kerosine flash point. The No. 2 crude distillation unit (CDU-2) at Singapore Refining Co. Pte. Ltd.'s Pulau Merlimau refinery has a nominal 130,000 b/d capacity. It produces naphtha, kerosine, diesel, and residue products from a wide range of crude blends. Over the past 12 months, extensive advanced control applications have been implemented on the unit. This first of two articlesmore » will describe the control system and its implementation. The second will outline the project's achievements, including reduced quality giveaway and increased profits. The paper describes background of the company and unit, the process, project implementation, the Infer model, model tuning, closed-loop control, feed rate maximization, and economic monitoring.« less

Interim results of quality-control sampling of surface water for the Upper Colorado River National Water-Quality Assessment Study Unit, water years 1995-96

USGS Publications Warehouse

Spahr, N.E.; Boulger, R.W.

1997-01-01

Quality-control samples provide part of the information needed to estimate the bias and variability that result from sample collection, processing, and analysis. Quality-control samples of surface water collected for the Upper Colorado River National Water-Quality Assessment study unit for water years 1995?96 are presented and analyzed in this report. The types of quality-control samples collected include pre-processing split replicates, concurrent replicates, sequential replicates, post-processing split replicates, and field blanks. Analysis of the pre-processing split replicates, concurrent replicates, sequential replicates, and post-processing split replicates is based on differences between analytical results of the environmental samples and analytical results of the quality-control samples. Results of these comparisons indicate that variability introduced by sample collection, processing, and handling is low and will not affect interpretation of the environmental data. The differences for most water-quality constituents is on the order of plus or minus 1 or 2 lowest rounding units. A lowest rounding unit is equivalent to the magnitude of the least significant figure reported for analytical results. The use of lowest rounding units avoids some of the difficulty in comparing differences between pairs of samples when concentrations span orders of magnitude and provides a measure of the practical significance of the effect of variability. Analysis of field-blank quality-control samples indicates that with the exception of chloride and silica, no systematic contamination of samples is apparent. Chloride contamination probably was the result of incomplete rinsing of the dilute cleaning solution from the outlet ports of the decaport sample splitter. Silica contamination seems to have been introduced by the blank water. Sampling and processing procedures for water year 1997 have been modified as a result of these analyses.

Feedback control in deep drawing based on experimental datasets

NASA Astrophysics Data System (ADS)

Fischer, P.; Heingärtner, J.; Aichholzer, W.; Hortig, D.; Hora, P.

2017-09-01

In large-scale production of deep drawing parts, like in automotive industry, the effects of scattering material properties as well as warming of the tools have a significant impact on the drawing result. In the scope of the work, an approach is presented to minimize the influence of these effects on part quality by optically measuring the draw-in of each part and adjusting the settings of the press to keep the strain distribution, which is represented by the draw-in, inside a certain limit. For the design of the control algorithm, a design of experiments for in-line tests is used to quantify the influence of the blank holder force as well as the force distribution on the draw-in. The results of this experimental dataset are used to model the process behavior. Based on this model, a feedback control loop is designed. Finally, the performance of the control algorithm is validated in the production line.

A Kind of Transformation of Information Service--Science and Technology Novelty Search in Chinese University Libraries

ERIC Educational Resources Information Center

Aiguo, Li

2007-01-01

Science and Technology Novelty Search (S&TNS) is a special information consultation service developed as part of the Chinese Sci-Tech system. The author introduces the concept of S&TNS, and explains its role, and the role of the university library in the process. A quality control model to improve the quality of service of the S&TNS at…

Flared landing approach flying qualities. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Weingarten, Norman C.; Berthe, Charles J., Jr.; Rynaski, Edmund G.; Sarrafian, Shahan K.

1986-01-01

An in-flight research study was conducted utilizing the USAF/Total In-Flight Simulator (TIFS) to investigate longitudinal flying qualities for the flared landing approach phase of flight. A consistent set of data were generated for: determining what kind of command response the pilot prefers/requires in order to flare and land an aircraft with precision, and refining a time history criterion that took into account all the necessary variables and the characteristics that would accurately predict flying qualities. Seven evaluation pilots participated representing NASA Langley, NASA Dryden, Calspan, Boeing, Lockheed, and DFVLR (Braunschweig, Germany). The results of the first part of the study provide guidelines to the flight control system designer, using MIL-F-8785-(C) as a guide, that yield the dynamic behavior pilots prefer in flared landings. The results of the second part provide the flying qualities engineer with a derived flying qualities predictive tool which appears to be highly accurate. This time-domain predictive flying qualities criterion was applied to the flight data as well as six previous flying qualities studies, and the results indicate that the criterion predicted the flying qualities level 81% of the time and the Cooper-Harper pilot rating, within + or - 1%, 60% of the time.

Flared landing approach flying qualities. Volume 1: Experiment design and analysis

NASA Technical Reports Server (NTRS)

Weingarten, Norman C.; Berthe, Charles J., Jr.; Rynaski, Edmund G.; Sarrafian, Shahan K.

1986-01-01

An inflight research study was conducted utilizing the USAF Total Inflight Simulator (TIFS) to investigate longitudinal flying qualities for the flared landing approach phase of flight. The purpose of the experiment was to generate a consistent set of data for: (1) determining what kind of commanded response the pilot prefers in order to flare and land an airplane with precision, and (2) refining a time history criterion that took into account all the necessary variables and their characteristics that would accurately predict flying qualities. The result of the first part provides guidelines to the flight control system designer, using MIL-F-8785-(C) as a guide, that yield the dynamic behavior pilots perfer in flared landings. The results of the second part provides the flying qualities engineer with a newly derived flying qualities predictive tool which appears to be highly accurate. This time domain predictive flying qualities criterion was applied to the flight data as well as six previous flying qualities studies, and the results indicate that the criterion predicted the flying qualities level 81% of the time and the Cooper-Harper pilot rating, within + or - 1, 60% of the time.

Perceived stress mediates the relationship between emotional loneliness and sleep quality over time in older adults.

PubMed

McHugh, Joanna E; Lawlor, Brian A

2013-09-01

Both loneliness and poor sleep quality are common occurrences in late life and both are detrimental to physical and mental health. While loneliness may be difficult to intervene upon, there may be correlated factors, which, if alleviated, could mitigate the effects of loneliness and sleep quality on health in late life. A longitudinal, observational study whereby we gathered predictive variables at baseline and dependent variable (sleep) at follow-up. We investigated the relationship between loneliness at baseline and sleep quality at follow-up in a group of 447 older adults attending the clinic for research participation. Loneliness, stress and sleep quality were all measured using self-report validated psychometric tools. We found that loneliness, specifically emotional loneliness, predicted sleep quality at follow-up, controlling for demographic factors and for sleep quality at baseline. Upon applying mediation methods to the data, we then found that this relationship was mediated in part by perceived stress. We conclude that the impact of emotional loneliness on sleep quality in older adults is partly because of the stress experienced as a result of feeling lonely. © 2012 The British Psychological Society.

Protein quality control in organelles - AAA/FtsH story.

PubMed

Janska, Hanna; Kwasniak, Malgorzata; Szczepanowska, Joanna

2013-02-01

This review focuses on organellar AAA/FtsH proteases, whose proteolytic and chaperone-like activity is a crucial component of the protein quality control systems of mitochondrial and chloroplast membranes. We compare the AAA/FtsH proteases from yeast, mammals and plants. The nature of the complexes formed by AAA/FtsH proteases and the current view on their involvement in degradation of non-native organellar proteins or assembly of membrane complexes are discussed. Additional functions of AAA proteases not directly connected with protein quality control found in yeast and mammals but not yet in plants are also described shortly. Following an overview of the molecular functions of the AAA/FtsH proteases we discuss physiological consequences of their inactivation in yeast, mammals and plants. The molecular basis of phenotypes associated with inactivation of the AAA/FtsH proteases is not fully understood yet, with the notable exception of those observed in m-AAA protease-deficient yeast cells, which are caused by impaired maturation of mitochondrial ribosomal protein. Finally, examples of cytosolic events affecting protein quality control in mitochondria and chloroplasts are given. This article is part of a Special Issue entitled: Protein Import and Quality Control in Mitochondria and Plastids. Copyright © 2012 Elsevier B.V. All rights reserved.

Dynamic Feed Control For Injection Molding

DOEpatents

Kazmer, David O.

1996-09-17

The invention provides methods and apparatus in which mold material flows through a gate into a mold cavity that defines the shape of a desired part. An adjustable valve is provided that is operable to change dynamically the effective size of the gate to control the flow of mold material through the gate. The valve is adjustable while the mold material is flowing through the gate into the mold cavity. A sensor is provided for sensing a process condition while the part is being molded. During molding, the valve is adjusted based at least in part on information from the sensor. In the preferred embodiment, the adjustable valve is controlled by a digital computer, which includes circuitry for acquiring data from the sensor, processing circuitry for computing a desired position of the valve based on the data from the sensor and a control data file containing target process conditions, and control circuitry for generating signals to control a valve driver to adjust the position of the valve. More complex embodiments include a plurality of gates, sensors, and controllable valves. Each valve is individually controllable so that process conditions corresponding to each gate can be adjusted independently. This allows for great flexibility in the control of injection molding to produce complex, high-quality parts.

Comparative mass spectrometry & nuclear magnetic resonance metabolomic approaches for nutraceuticals quality control analysis: a brief review.

PubMed

Farag, Mohamed A

2014-01-01

The number of botanical dietary supplements in the market has recently increased primarily due to increased health awareness. Standardization and quality control of the constituents of these plant extracts is an important topic, particularly when such ingredients are used long term as dietary supplements, or in cases where higher doses are marketed as drugs. The development of fast, comprehensive, and effective untargeted analytical methods for plant extracts is of high interest. Nuclear magnetic resonance spectroscopy and mass spectrometry are the most informative tools, each of which enables high-throughput and global analysis of hundreds of metabolites in a single step. Although only one of the two techniques is utilized in the majority of plant metabolomics applications, there is a growing interest in combining the data from both platforms to effectively unravel the complexity of plant samples. The application of combined MS and NMR in the quality control of nutraceuticals forms the major part of this review. Finally I will look at the future developments and perspectives of these two technologies for the quality control of herbal materials.

78 FR 72609 - Approval and Promulgation of State Air Quality Plans for Designated Facilities and Pollutants...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-03

..., subpart B and part 62, subpart A. Section 129 of the CAA regulates air pollutants that include organics... pollution control, Aluminum, Fertilizers, Fluoride, Intergovernmental relations, Paper and paper products...

76 FR 76929 - Approval and Promulgation of Air Quality Implementation Plans; Delaware, Maryland, New Jersey...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-09

... active outdoors, and individuals with a pre-existing respiratory disease, such as asthma. On April 30... in 40 CFR Part 52 Environmental protection, Air pollution control, Intergovernmental relations, Ozone...

V/STOL Dynamics, Control, and Flying Qualities

NASA Technical Reports Server (NTRS)

Franklin, James A.

2000-01-01

This publication presents material that constituted the lectures presented by the author as part of Course AA 234, Dynamics, Control, and Flying Qualities of Vertical/Short Takeoff and Landing (V/STOL) Aircraft that was taught in the Department of Aeronautics and Astronautics at Stanford University. It covers representative operations of vertical and short takeoff and landing (V/STOL) aircraft, a discussion of the pilot's strategy in controlling these aircraft, the equations of motion pertinent to V/STOL tasks, and their application in the analysis of longitudinal and lateral-directional control in hover and forward flight. Following that development, which applies to the characteristics of the basic airframe and propulsion system, the text concludes with a discussion of the contributions of control augmentation in specific flight tasks and of the integration of modern electronic displays with these controls.

76 FR 11453 - Dinotefuran; Receipt of Application for Emergency Exemption, Solicitation of Public Comment

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-02

... rice to control rice stink bug (Oebalus pugnax). The applicant proposes a use which has been requested... rice to control rice stink bug (Oebalus pugnax). Information in accordance with 40 CFR part 166 was... rice stink bug in this case is not yield loss, but rather quality loss in the harvested rice. Its...

Laser-assisted micro sheet forming

NASA Astrophysics Data System (ADS)

Holtkamp, Jens; Gillner, Arnold

2008-01-01

The fast growing market for micro technical products requires parts with increasing complexity. While sheet metal forming enables low cost mass production with short cycle times, it is limited by the maximum degree of deformation and the quality of the cut edge. The technology of warm forming partially eliminates these deficiencies. This operation takes place at elevated temperatures before structural transformation is initiated. It combines characteristic advantages of traditional cold and hot forming processes. Lasers as heat sources provide a high, selective and controllable energy input. The general difficulty of a uniform temperature distribution during the heating process can be reached by using an Axicon which generates an annulus on the sheet metal surface. The temperature of the workpiece, measured by a pyrometer, is tuned by a PI-Controller. A tool incorporating a multistage operation die is used for the manufacturing of up to three parts at the same time. The tool is integrated into a hydraulical press. A gearwheel made of the magnesium alloy AZ31 is chosen as metal demonstrator. The quality of these punched parts could be significantly improved at elevated temperatures

Effect of Tooling Material on the Internal Surface Quality of Ti6Al4V Parts Fabricated by Hot Isostatic Pressing

NASA Astrophysics Data System (ADS)

Cai, Chao; Song, Bo; Wei, Qingsong; Yan, Wu; Xue, Pengju; Shi, Yusheng

2017-01-01

For the net-shape hot isostatic pressing (HIP) process, control of the internal surface roughness of as-HIPped parts remains a challenge for practical engineering. To reveal the evolution mechanism of the internal surface of the parts during the HIP process, the effect of different tooling materials (H13, T8, Cr12 steel, and graphite) as internal cores on the interfacial diffusion and surface roughness was systematically studied.

Research of Sleep Disorders in Patients with Acute Cerebral Infarction.

PubMed

Chen, Xiaofang; Bi, Hongye; Zhang, Meiyun; Liu, Haiyan; Wang, Xueying; Zu, Ruonan

2015-11-01

The purpose of this study is to investigate the incidence of sleep disorders (SD), characteristic of cerebral infarction patients with different parts affected. The research selected 101 patients with a first occurrence of acute cerebral infarction as the experimental group, and 86 patients without cerebral infarction as controls. Polysomnography, Pittsburgh Sleep Quality Index, Epworth Sleepiness Scale, and US National Stroke Scale were assessed. Compared with control group, the incidence of SD was higher in experimental group (P < .05), and the incidence of SD in women was more frequent in experimental group (P < .05). There was no significant difference in the types of SD patients with acute cerebral infarction. In addition, the sleep quality of cerebral infarction patients with different parts affected was different: the sleep quality of left hemisphere infarction patients was poor compared with the right one, and the sleep quality of anterior circulation patients was poor compared with posterior circulation patients. Patients with thalamus infarction had a longer sleep time and a shorter sleep latency and stage 2 of non-rapid eye movement sleep compared with non-thalamus infarction group. The prevalence of SD was relatively high in acute cerebral infarction patients, and the detailed classification of acute cerebral infarction may provide a more effective therapeutic method and therefore relieve patients' pain and supply a better quality of sleep. Copyright © 2015 National Stroke Association. Published by Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malkoske, Kyle; Nielsen, Michelle; Brown, Erika

The Canadian Partnership for Quality Radiotherapy (CPQR) and the Canadian Organization of Medical Physicist’s (COMP) Quality Assurance and Radiation Safety Advisory Committee (QARSAC) have worked together in the development of a suite of Technical Quality Control (TQC) Guidelines for radiation treatment equipment and technologies, that outline specific performance objectives and criteria that equipment should meet in order to assure an acceptable level of radiation treatment quality. Early community engagement and uptake survey data showed 70% of Canadian centers are part of this process and that the data in the guideline documents reflect, and are influencing the way Canadian radiation treatmentmore » centres run their technical quality control programs. As the TQC development framework matured as a cross-country initiative, guidance documents have been developed in many clinical technologies. Recently, there have been new TQC documents initiated for Gamma Knife and Cyberknife technologies where the entire communities within Canada are involved in the review process. At the same time, QARSAC reviewed the suite as a whole for the first time and it was found that some tests and tolerances overlapped across multiple documents as single tests could pertain to multiple quality control areas. The work to streamline the entire suite has allowed for improved usability of the suite while keeping the integrity of single quality control areas. The suite will be published by the JACMP, in the coming year.« less

[Compatibility of different quality control systems].

PubMed

Invernizzi, Enrico

2002-01-01

Management of the good laboratory practice (GLP) quality system presupposes its linking to a basic recognized and approved quality system, from which it can draw on management procedures common to all quality systems, such as the ISO 9000 set of norms. A quality system organized in this way can also be integrated with other dedicated quality systems, or parts of them, to obtain principles or management procedures for specific topics. The aim of this organization is to set up a reliable, recognized quality system compatible with the principles of GLP and other quality management systems, which provides users with a simplified set of easily accessible management tools and answers. The organization of this quality system is set out in the quality assurance programme, which is actually the document in which the test facility incorporates the GLP principles into its own quality organization.

A multichannel amplitude and relative-phase controller for active sound quality control

NASA Astrophysics Data System (ADS)

Mosquera-Sánchez, Jaime A.; Desmet, Wim; de Oliveira, Leopoldo P. R.

2017-05-01

The enhancement of the sound quality of periodic disturbances for a number of listeners within an enclosure often confronts difficulties given by cross-channel interferences, which arise from simultaneously profiling the primary sound at each error sensor. These interferences may deteriorate the original sound among each listener, which is an unacceptable result from the point of view of sound quality control. In this paper we provide experimental evidence on controlling both amplitude and relative-phase functions of stationary complex primary sounds for a number of listeners within a cavity, attaining amplifications of twice the original value, reductions on the order of 70 dB, and relative-phase shifts between ± π rad, still in a free-of-interference control scenario. To accomplish such burdensome control targets, we have designed a multichannel active sound profiling scheme that bases its operation on exchanging time-domain control signals among the control units during uptime. Provided the real parts of the eigenvalues of persistently excited control matrices are positive, the proposed multichannel array is able to counterbalance cross-channel interferences, while attaining demanding control targets. Moreover, regularization of unstable control matrices is not seen to prevent the proposed array to provide free-of-interference amplitude and relative-phase control, but the system performance is degraded, as a function of the amount of regularization needed. The assessment of Loudness and Roughness metrics on the controlled primary sound proves that the proposed distributed control scheme noticeably outperforms current techniques, since active amplitude- and/or relative-phase-based enhancement of the auditory qualities of a primary sound no longer implies in causing interferences among different positions. In this regard, experimental results also confirm the effectiveness of the proposed scheme on stably enhancing the sound qualities of periodic sounds for multiple listeners within a cavity.

[The participation of patients with dementia in individualised intervention plan meetings: the impact on their well-being and the quality of life].

PubMed

Villar, Feliciano; Vila-Miravent, Josep; Celdrán, Montserrat; Fernández, Elena

2013-01-01

An individualised intervention plan (IIP) offers a new paradigm in the care of the elderly with dementia, with the aim of increasing their quality of life through personalisation, respect for their freedom, and their participation in the decisions that affect their lives. To evaluate the impact of the residential home patient with dementia and their quality of care when they take part in the interdisciplinary meeting in which their care plan is decided. A total of 52 elderly patients with dementia took part in the study. They were distributed into two groups, one experimental (37 residents) and another control (15 residents). The Dementia Care Mapping (DCM) tool was used to assess the well-being and quality of care of the residents. This tool was used twice, before and after the intervention. The well-being of the resident, evaluated using the DCM, was similar before and after the intervention in the experimental group. No differences were observed either on comparing the control and experimental groups. However, some indicators of carer behaviour were different before and after the intervention, and when the control and experimental group were compared. The inclusion of elderly persons with dementia in their IIP meeting had a positive effect in the interaction of the staff with the residents, but not on the well-being of the resident. Copyright © 2012 SEGG. Published by Elsevier Espana. All rights reserved.

Quality of life of people with mental health problems: a synthesis of qualitative research

PubMed Central

2012-01-01

Purpose To identify the domains of quality of life important to people with mental health problems. Method A systematic review of qualitative research undertaken with people with mental health problems using a framework synthesis. Results We identified six domains: well-being and ill-being; control, autonomy and choice; self-perception; belonging; activity; and hope and hopelessness. Firstly, symptoms or ‘ill-being’ were an intrinsic aspect of quality of life for people with severe mental health problems. Additionally, a good quality of life was characterised by the feeling of being in control (particularly of distressing symptoms), autonomy and choice; a positive self-image; a sense of belonging; engagement in meaningful and enjoyable activities; and feelings of hope and optimism. Conversely, a poor quality life, often experienced by those with severe mental health difficulties, was characterized by feelings of distress; lack of control, choice and autonomy; low self-esteem and confidence; a sense of not being part of society; diminished activity; and a sense of hopelessness and demoralization. Conclusions Generic measures fail to address the complexity of quality of life measurement and the broad range of domains important to people with mental health problems. PMID:23173689

An experimental study of factors affecting the selective inhibition of sintering process

NASA Astrophysics Data System (ADS)

Asiabanpour, Bahram

Selective Inhibition of Sintering (SIS) is a new rapid prototyping method that builds parts in a layer-by-layer fabrication basis. SIS works by joining powder particles through sintering in the part's body, and by sintering inhibition of some selected powder areas. The objective of this research has been to improve the new SIS process, which has been invented at USC. The process improvement is based on statistical design of experiments. To conduct the needed experiments a working machine and related path generator software were needed. The machine and its control software were made available prior to this research. The path generator algorithms and software had to be created. This program should obtain model geometry data from a CAD file and generate an appropriate path file for the printer nozzle. Also, the program should generate a simulation file for path file inspection using virtual prototyping. The activities related to path generator constitute the first part of this research, which has resulted in an efficient path generator. In addition, to reach an acceptable level of accuracy, strength, and surface quality in the fabricated parts, all effective factors in the SIS process should be identified and controlled. Simultaneous analytical and experimental studies were conducted to recognize effective factors and to control the SIS process. Also, it was known that polystyrene was the most appropriate polymer powder and saturated potassium iodide was the most effective inhibitor among the available candidate materials. In addition, statistical tools were applied to improve the desirable properties of the parts fabricated by the SIS process. An investigation of part strength was conducted using the Response Surface Methodology (RSM) and a region of acceptable operating conditions for the part strength was found. Then, through analysis of the experimental results, the impact of the factors on the final part surface quality and dimensional accuracy was modeled. After developing a desirability function model, process operating conditions for maximum desirability were identified. Finally, the desirability model was validated.

Electronic symptom reporting between patient and provider for improved health care service quality: a systematic review of randomized controlled trials. part 2: methodological quality and effects.

PubMed

Johansen, Monika Alise; Berntsen, Gro K Rosvold; Schuster, Tibor; Henriksen, Eva; Horsch, Alexander

2012-10-03

We conducted in two parts a systematic review of randomized controlled trials (RCTs) on electronic symptom reporting between patients and providers to improve health care service quality. Part 1 reviewed the typology of patient groups, health service innovations, and research targets. Four innovation categories were identified: consultation support, monitoring with clinician support, self-management with clinician support, and therapy. To assess the methodological quality of the RCTs, and summarize effects and benefits from the methodologically best studies. We searched Medline, EMBASE, PsycINFO, Cochrane Central Register of Controlled Trials, and IEEE Xplore for original studies presented in English-language articles between 1990 and November 2011. Risk of bias and feasibility were judged according to the Cochrane recommendation, and theoretical evidence and preclinical testing were evaluated according to the Framework for Design and Evaluation of Complex Interventions to Improve Health. Three authors assessed the risk of bias and two authors extracted the effect data independently. Disagreement regarding bias assessment, extraction, and interpretation of results were resolved by consensus discussions. Of 642 records identified, we included 32 articles representing 29 studies. No articles fulfilled all quality requirements. All interventions were feasible to implement in a real-life setting, and theoretical evidence was provided for almost all studies. However, preclinical testing was reported in only a third of the articles. We judged three-quarters of the articles to have low risk for random sequence allocation and approximately half of the articles to have low risk for the following biases: allocation concealment, incomplete outcome data, and selective reporting. Slightly more than one fifth of the articles were judged as low risk for blinding of outcome assessment. Only 1 article had low risk of bias for blinding of participants and personnel. We excluded 12 articles showing high risk or unclear risk for both selective reporting and blinding of outcome assessment from the effect assessment. The authors' hypothesis was confirmed for 13 (65%) of the 20 remaining articles. Articles on self-management support were of higher quality, allowing us to assess effects in a larger proportion of studies. All except one self-management interventions were equally effective to or better than the control option. The self-management articles document substantial benefits for patients, and partly also for health professionals and the health care system. Electronic symptom reporting between patients and providers is an exciting area of development for health services. However, the research generally is of low quality. The field would benefit from increased focus on methods for conducting and reporting RCTs. It appears particularly important to improve blinding of outcome assessment and to precisely define primary outcomes to avoid selective reporting. Supporting self-management seems to be especially promising, but consultation support also shows encouraging results.

Electronic Symptom Reporting Between Patient and Provider for Improved Health Care Service Quality: A Systematic Review of Randomized Controlled Trials. Part 2: Methodological Quality and Effects

PubMed Central

Berntsen, Gro K Rosvold; Schuster, Tibor; Henriksen, Eva; Horsch, Alexander

2012-01-01

Background We conducted in two parts a systematic review of randomized controlled trials (RCTs) on electronic symptom reporting between patients and providers to improve health care service quality. Part 1 reviewed the typology of patient groups, health service innovations, and research targets. Four innovation categories were identified: consultation support, monitoring with clinician support, self-management with clinician support, and therapy. Objective To assess the methodological quality of the RCTs, and summarize effects and benefits from the methodologically best studies. Methods We searched Medline, EMBASE, PsycINFO, Cochrane Central Register of Controlled Trials, and IEEE Xplore for original studies presented in English-language articles between 1990 and November 2011. Risk of bias and feasibility were judged according to the Cochrane recommendation, and theoretical evidence and preclinical testing were evaluated according to the Framework for Design and Evaluation of Complex Interventions to Improve Health. Three authors assessed the risk of bias and two authors extracted the effect data independently. Disagreement regarding bias assessment, extraction, and interpretation of results were resolved by consensus discussions. Results Of 642 records identified, we included 32 articles representing 29 studies. No articles fulfilled all quality requirements. All interventions were feasible to implement in a real-life setting, and theoretical evidence was provided for almost all studies. However, preclinical testing was reported in only a third of the articles. We judged three-quarters of the articles to have low risk for random sequence allocation and approximately half of the articles to have low risk for the following biases: allocation concealment, incomplete outcome data, and selective reporting. Slightly more than one fifth of the articles were judged as low risk for blinding of outcome assessment. Only 1 article had low risk of bias for blinding of participants and personnel. We excluded 12 articles showing high risk or unclear risk for both selective reporting and blinding of outcome assessment from the effect assessment. The authors’ hypothesis was confirmed for 13 (65%) of the 20 remaining articles. Articles on self-management support were of higher quality, allowing us to assess effects in a larger proportion of studies. All except one self-management interventions were equally effective to or better than the control option. The self-management articles document substantial benefits for patients, and partly also for health professionals and the health care system. Conclusion Electronic symptom reporting between patients and providers is an exciting area of development for health services. However, the research generally is of low quality. The field would benefit from increased focus on methods for conducting and reporting RCTs. It appears particularly important to improve blinding of outcome assessment and to precisely define primary outcomes to avoid selective reporting. Supporting self-management seems to be especially promising, but consultation support also shows encouraging results. PMID:23032363

76 FR 41561 - Approval and Promulgation of Implementation Plans; California; 2007 South Coast PM2.5

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-14

...EPA is proposing to approve in part and disapprove in part state implementation plan (SIP) revisions submitted by California to provide for attainment of the 1997 fine particulate matter (PM2.5) national ambient air quality standards in the Los Angeles-South Coast area (South Coast). These SIP revisions are the South Coast 2007 Air Quality Management Plan (South Coast 2007 AQMP) (revised 2011) and South Coast-related provisions of the 2007 State Strategy (revised 2009 and 2011). EPA is proposing to approve the emissions inventories; air quality modeling; reasonably available control measures/reasonably available control technology demonstration; the reasonable further progress and attainment demonstrations; and the transportation conformity motor vehicle emissions budgets. EPA is also proposing to grant California's request to extend the attainment deadline for the South Coast to April 5, 2015 and to approve commitments to measures and reductions by the South Coast Air Quality Management District and the California Air Resources Board. Finally, we are proposing to disapprove the SIP's contingency measures and to reject the assignment of 10 tpd of NOX reductions to the federal government. This proposed rule amends EPA's November 22, 2010 proposed rule (75 FR 91294) on the South Coast PM2.5 plan and 2007 State strategy.

76 FR 77974 - U.S. Automotive Parts and Components Business Development Mission to Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-15

... mission is designed to provide an opportunity to explore Russia's rapidly expanding car and truck assembly... available cars, most based on 1960s technology. Quality control was minimal. In 2010, automobile ownership...

Pseudocontamination of blood components with Burkholderia cepacia during quality controls.

PubMed

Ebner, W; Meyer, E; Schulz-Huotari, C; Scholz, R; Zilow, G; Daschner, F D

2005-06-01

We report on a pseudooutbreak of Burkholderia cepacia because of the use of a contaminated disinfectant during quality controls in a university blood bank. No septic reactions associated with transfusions had been reported in patients over the last 6 months. Analysis of the individual quality control procedures showed that a disinfectant based on a quaternary ammonium compound (QAC) had been used in order to disinfect the rubber stopper of the blood culture bottle. B. cepacia was found in a sample taken from this disinfectant, which was prepared with concentrate and tap water according to the manufacturer's instructions. The four isolates (one in disinfectant and three in blood components) were found to be identical in their biochemical reactions and resistance patterns. QAC-based disinfectants are not efficacious against a part of the spectrum of gram-negatives and are therefore inadequate. After introduction of an alcohol-based preparation, no more cases of B. cepacia contamination have been identified.

Simulation of intelligent object behavior in a virtual reality system

NASA Astrophysics Data System (ADS)

Mironov, Sergey F.

1998-01-01

This article presents a technique for computer control of a power boat movement in real-time marine trainers or arcade games. The author developed and successfully implemented a general technique allowing intellectual navigation of computer controlled moving objects that proved to be appropriate for real-time applications. This technique covers significant part of necessary behavioral tasks that appear in such titles. At the same time the technique forms a part of a more general system that involves control of less complicated characters of another nature. The system being an open one can be easily used by an action or arcade programming to improve the overall quality of characters artificial intelligence style.

Infection prevention and control practitioners: improving engagement.

PubMed

Aziz, Ann-Marie

Every healthcare worker plays a vital part in minimising the risk of cross infection. Infection prevention and control (IPC) practitioners have the skills and competencies to assist organisations in improving engagement among staff and play a vital part in achieving this. IPC practitioners have skills in clinical practice, education, research and leadership, and these skills ensure high-quality care for patients and support strategies for engaging staff. This article highlights how IPC practitioners' skills and competencies are required for preventing infection and improving staff engagement. Engaged staff generate positive outcomes for both patients and staff, which is a welcome result for all healthcare organisations.

Standardisation of DNA quantitation by image analysis: quality control of instrumentation.

PubMed

Puech, M; Giroud, F

1999-05-01

DNA image analysis is frequently performed in clinical practice as a prognostic tool and to improve diagnosis. The precision of prognosis and diagnosis depends on the accuracy of analysis and particularly on the quality of image analysis systems. It has been reported that image analysis systems used for DNA quantification differ widely in their characteristics (Thunissen et al.: Cytometry 27: 21-25, 1997). This induces inter-laboratory variations when the same sample is analysed in different laboratories. In microscopic image analysis, the principal instrumentation errors arise from the optical and electronic parts of systems. They bring about problems of instability, non-linearity, and shading and glare phenomena. The aim of this study is to establish tools and standardised quality control procedures for microscopic image analysis systems. Specific reference standard slides have been developed to control instability, non-linearity, shading and glare phenomena and segmentation efficiency. Some systems have been controlled with these tools and these quality control procedures. Interpretation criteria and accuracy limits of these quality control procedures are proposed according to the conclusions of a European project called PRESS project (Prototype Reference Standard Slide). Beyond these limits, tested image analysis systems are not qualified to realise precise DNA analysis. The different procedures presented in this work determine if an image analysis system is qualified to deliver sufficiently precise DNA measurements for cancer case analysis. If the controlled systems are beyond the defined limits, some recommendations are given to find a solution to the problem.

A state of the art regarding urban air quality prediction models

NASA Astrophysics Data System (ADS)

Croitoru, Cristiana; Nastase, Ilinca

2018-02-01

Urban pollution represents an increasing risk to residents of urban regions, particularly in large, over-industrialized cities knowing that the traffic is responsible for more than 25% of air gaseous pollutants and dust particles. Air quality modelling plays an important role in addressing air pollution control and management approaches by providing guidelines for better and more efficient air quality forecasting, along with smart monitoring sensor networks. The advances in technology regarding simulations, forecasting and monitoring are part of the new smart cities which offers a healthy environment for their occupants.

Sleep and chronobiology in cluster headache.

PubMed

Barloese, M; Lund, N; Petersen, A; Rasmussen, M; Jennum, P; Jensen, R

2015-10-01

Cluster headache (CH) is the headache disorder with the strongest chronobiological traits. The severe attacks of pain occur with diurnal and annual rhythmicity but the precise rhythm and involvement of potential zeitgebers is unknown. Patients complain of poor sleep quality yet this has never been studied. We investigated triggers, rhythms, sleep quality and chronotypes in CH. Patients and controls completed questionnaires and structured interviews composed of new and previously validated parts including the Pittsburgh Sleep Quality Index (PSQI) and Morningness-Eveningness Questionnaire (MEQ). Patients were characterized by a CH index, a unified measure of headache burden. A total of 275 CH patients and 145 matched controls were included. The most common trigger was sleep (80%) and a relationship between clusters and daylight was identified. Of the patients, 82.2% reported diurnal and 56% annual rhythmicity. Patients reported impaired sleep quality (PSQI) (p < 0.0001) and an inverse relationship between time passed since last attack and sleep quality was identified (p < 0.0001). The CH index was positively related to the PSQI (p < 0.0001). Diurnally, CH exhibits a relationship with night-time and annually with daylight hours. Patients' sleep quality is reduced compared with controls. Results suggest a complex relationship as sleep quality improves between clusters, but remains pathological. © International Headache Society 2015.

An introduction to statistical process control in research proteomics.

PubMed

Bramwell, David

2013-12-16

Statistical process control is a well-established and respected method which provides a general purpose, and consistent framework for monitoring and improving the quality of a process. It is routinely used in many industries where the quality of final products is critical and is often required in clinical diagnostic laboratories [1,2]. To date, the methodology has been little utilised in research proteomics. It has been shown to be capable of delivering quantitative QC procedures for qualitative clinical assays [3] making it an ideal methodology to apply to this area of biological research. To introduce statistical process control as an objective strategy for quality control and show how it could be used to benefit proteomics researchers and enhance the quality of the results they generate. We demonstrate that rules which provide basic quality control are easy to derive and implement and could have a major impact on data quality for many studies. Statistical process control is a powerful tool for investigating and improving proteomics research work-flows. The process of characterising measurement systems and defining control rules forces the exploration of key questions that can lead to significant improvements in performance. This work asserts that QC is essential to proteomics discovery experiments. Every experimenter must know the current capabilities of their measurement system and have an objective means for tracking and ensuring that performance. Proteomic analysis work-flows are complicated and multi-variate. QC is critical for clinical chemistry measurements and huge strides have been made in ensuring the quality and validity of results in clinical biochemistry labs. This work introduces some of these QC concepts and works to bridge their use from single analyte QC to applications in multi-analyte systems. This article is part of a Special Issue entitled: Standardization and Quality Control in Proteomics. Copyright © 2013 The Author. Published by Elsevier B.V. All rights reserved.

40 CFR 60.4861 - How do I establish an affirmative defense for exceedance of an emission limit or standard during...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., and unavoidable failure of air pollution control and monitoring equipment, process equipment, or a... activity or event that could have been foreseen and avoided, or planned for, and (iv) Were not part of a... ambient air quality, the environment and human health, and (6) All emissions monitoring and control...

40 CFR 60.4861 - How do I establish an affirmative defense for exceedance of an emission limit or standard during...

Code of Federal Regulations, 2012 CFR

2012-07-01

..., and unavoidable failure of air pollution control and monitoring equipment, process equipment, or a... activity or event that could have been foreseen and avoided, or planned for, and (iv) Were not part of a... ambient air quality, the environment and human health, and (6) All emissions monitoring and control...

Quality assurance, an administrative means to a managerial end: Part IV.

PubMed

Clark, G B

1992-01-01

This is the fourth and final part of a series of articles on laboratory quality surveillance. Part I addressed the historical background of medical quality assurance. Part II covered surveillance guidelines of the Joint Commission on Accreditation of Healthcare Organizations (JCAHO) and the College of American Pathologists with emphasis on quality assurance (QA) and the ten-step process. Part III focused on the JCAHO transition from QA to quality assessment and improvement. Part IV concludes the series by discussing the systematic identification of quality indicators in the total quality management and continuous quality improvement environment.

[Population policy: the legacy of Greek thought].

PubMed

Elgegren Reategui, F

1994-01-01

The author "explains that the Greek philosophy and scientific thought developed elements of what is known today as population policies. These include roles and gender relationships, the population volume, the family, sexuality, birth control, eugenics, abortion and [quality of life]....The first part of the article reviews issues on family and women's roles. The second part is related to aspects associated with sexuality and...population policy." (SUMMARY IN ENG) excerpt

76 FR 41337 - Approval and Promulgation of Implementation Plans; California; 2008 San Joaquin Valley PM2.5

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-13

...EPA is proposing to approve in part and disapprove in part state implementation plan (SIP) revisions submitted by California to provide for attainment of the 1997 fine particulate matter (PM2.5) national ambient air quality standards in the San Joaquin Valley (SJV). These SIP revisions are the SJV 2008 PM2.5 Plan (revised 2010 and 2011) and SJV-related provisions of the 2007 State Strategy (revised 2009 and 2011). EPA is proposing to approve the emissions inventories; air quality modeling; the reasonably available control measures/reasonably available control technology, reasonable further progress, and attainment demonstrations; and the transportation conformity motor vehicle emissions budgets. EPA is also proposing to grant California's request to extend the attainment deadline for the SJV to April 5, 2015 and to approve commitments to measures and reductions by the SJV Air Pollution Control District and the California Air Resources Board. Finally, it is proposing to disapprove the SIP's contingency measures. This proposed rule amends EPA's November 30, 2010 proposed rule (75 FR 74518) on the SJV 2008 PM2.5 Plan and 2007 State Strategy.

EMISSIONS PROFILE CHARACTERIZATION OF LAKE MICHIGAN POLLUTANT SOURCES - PART I

EPA Science Inventory

The southern Lake Michigan aea continues to experience poor air quality despite the implementation of many measures to control particulate matter, ozone and toxic pollutants. Fortunately, the ambient atmosphere holds clues tothese sources and their contributions to urban polluti...

75 FR 25830 - Agency Information Collection Activities: Proposed Collection; Comment Request, Supplemental...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-10

... DEPARTMENT OF AGRICULTURE Food and Nutrition Service Agency Information Collection Activities: Proposed Collection; Comment Request, Supplemental Nutrition Assistance Program Regulations, Part 275--Quality Control AGENCY: Food and Nutrition Service, USDA. ACTION: Notice. SUMMARY: As required by the...

PRE-QUALITY ASSURANCE PROJECT PLAN (QAPP) AGREEMENT (PQA) (HANDOUT)

EPA Science Inventory

The Land Remediation and Pollution Control Division (LRPCD) QA Manager strives to assist LRPCD researchers in developing functional planning documents for their research projects. As part of the planning process, several pieces of information are needed, including information re...

Experiments and numerical simulations of flow field and heat transfer coefficients inside an autoclave model

NASA Astrophysics Data System (ADS)

Ghamlouch, T.; Roux, S.; Bailleul, J.-L.; Lefèvre, N.; Sobotka, V.

2017-10-01

Today's aerospace industrial first priority is the quality improvement of the composite material parts with the reduction of the manufacturing time in order to increase their quality/cost ratio. A fabrication method that could meet these specifications especially for large parts is the autoclave curing process. In fact the autoclave molding ensures the thermal control of the composite parts during the whole curing cycle. However the geometry of the tools as well as their positioning in the autoclave induce non uniform and complex flows around composite parts. This heterogeneity implies non-uniform heat transfers which can directly impact on part quality. One of the main challenges is therefore to describe the flow field inside an autoclave as well as the convective heat transfer from the heated pressurized gas to the composite part and the mold. For this purpose, and given the technical issues associated with instrumentation and measurements in actual autoclaves, an autoclave model was designed and then manufactured based on similarity laws. This tool allows the measurement of the flow field around representative real industrial molds using the PIV technique and the characterization of the heat transfer thanks to thermal instrumentation. The experimental results are then compared with those derived from numerical simulations using a commercial RANS CFD code. This study aims at developing a semi-empirical approach for the prediction of the heat transfer coefficient around the parts and therefore predicts its thermal history during the process with a view of optimization.

Quality control and quality assurance plan for bridge channel-stability assessments in Massachusetts

USGS Publications Warehouse

Parker, Gene W.; Pinson, Harlow

1993-01-01

A quality control and quality assurance plan has been implemented as part of the Massachusetts bridge scour and channel-stability assessment program. This program is being conducted by the U.S. Geological Survey, Massachusetts-Rhode Island District, in cooperation with the Massachusetts Highway Department. Project personnel training, data-integrity verification, and new data-management technologies are being utilized in the channel-stability assessment process to improve current data-collection and management techniques. An automated data-collection procedure has been implemented to standardize channel-stability assessments on a regular basis within the State. An object-oriented data structure and new image management tools are used to produce a data base enabling management of multiple data object classes. Data will be reviewed by assessors and data base managers before being merged into a master bridge-scour data base, which includes automated data-verification routines.

Summary of inorganic compositional data for groundwater, soil-water, and surface-water samples collected at the Headgate Draw subsurface drip irrigation site, Johnson County, Wyoming

USGS Publications Warehouse

Geboy, Nicholas J.; Engle, Mark A.; Schroeder, Karl T.; Zupancic, John W.

2011-01-01

As part of a 5-year project on the impact of subsurface drip irrigation (SDI) application of coalbed-methane (CBM) produced waters, water samples were collected from the Headgate Draw SDI site in the Powder River Basin, Wyoming, USA. This research is part of a larger study to understand short- and long-term impacts on both soil and water quality from the beneficial use of CBM waters to grow forage crops through use of SDI. This document provides a summary of the context, sampling methodology, and quality assurance and quality control documentation of samples collected prior to and over the first year of SDI operation at the site (May 2008-October 2009). This report contains an associated database containing inorganic compositional data, water-quality criteria parameters, and calculated geochemical parameters for samples of groundwater, soil water, surface water, treated CBM waters, and as-received CBM waters collected at the Headgate Draw SDI site.

Modeling Study on Air Quality Improvement due to Mobile Source Emission control Plan in Seoul Metropolitan Area

NASA Astrophysics Data System (ADS)

Kim, Y. J.; Sunwoo, Y.; Hwang, I.; Song, S.; Sin, J.; Kim, D.

2015-12-01

A very high population and corresponding high number of vehicles in the Seoul Metropolitan Area (SMA) are aggravating the air quality of this region. The Korean government continues to make concerted efforts to improve air quality. One of the major policies that the Ministry of Environment of Korea enforced is "The Special Act for Improvement of Air Quality in SMA" and "The 1st Air Quality Management Plan of SMA". Mobile Source emission controls are an important part of the policy. Thus, it is timely to evaluate the air quality improvement due to the controls. Therefore, we performed a quantitative analysis of the difference in air quality using the Community Multiscale Air Quality (CMAQ) model and December, 2011 was set as the target period to capture the impact of the above control plans. We considered four fuel-type vehicle emission scenarios and compared the air quality improvement differences between them. The scenarios are as follows: no-control, gasoline vehicle control only, diesel vehicle control only, and control of both; utilizing the revised mobile source emissions from the Clean Air Policy Support System (CAPSS), which is the national emission inventory reflecting current policy.In order to improve the accuracy of the modeling data, we developed new temporal allocation coefficients based on traffic volume observation data and spatially reallocated the mobile source emissions using vehicle flow survey data. Furthermore, we calculated the PM10 and PM2.5 emissions of gasoline vehicles which is omitted in CAPSS.The results of the air quality modeling shows that vehicle control plans for both gasoline and diesel lead to a decrease of 0.65ppb~8.75ppb and 0.02㎍/㎥~7.09㎍/㎥ in NO2 and PM10 monthly average concentrations, respectively. The large percentage decreases mainly appear near the center of the metropolis. However, the largest NO2 decrease percentages are found in the northeast region of Gyeonggi-do, which is the province that surrounds the capital of Seoul. Comparing the results between the different scenarios, diesel vehicle control impact dominates relative to the impact of gasoline control. The diesel-only reduction plan shows that NO2 and PM10 improved by 2.93ppb and 3.32㎍/㎥, respectively.

Improving the Quality of Hot Stamping Parts with Innovative Press Technology and Inline Process Control

NASA Astrophysics Data System (ADS)

Vollmer, R.; Palm, C.

2017-09-01

The increasing number of hot stamped parts in the automotive industry is challenging different process areas. This paper presents a method how to improve the production rates over the whole life cycle of a hot forming part. In the core element of a hot forming line, the hydraulic press, mainly two processing steps are performed. Forming and quenching of the sheet metal part. In addition to the forming operation, it is inevitable to optimize the quenching condition in the bottom dead centre in order to reach a fully martensitic structure and tight geometrical tolerances of the part. Deviations in the blank thickness, tool wear, polishing of classical tools impair the quenching condition and therefore the part quality over the time. A new press and tool design has been developed to counter this effect by providing homogenous contact pressure over the whole die. Especially with a multi cavity tool, the new method is advantageous. Test series have shown that the new tool and press concept can produce parts with a blank thickness of 1.0 mm within 8.0 s cycle time. The so called PCH flex principle makes it possible to produce such high output rates under reliable conditions.

The Effects of Aromatherapy on Intensive Care Unit Patients' Stress and Sleep Quality: A Nonrandomised Controlled Trial

PubMed Central

Cho, Eun Hee; Lee, Mi-Young

2017-01-01

Background Stress has both physiological and psychological effects and can negatively impact patients' treatment and recovery. We examined whether the aromatherapy alleviated patients' stress and improved their sleep quality and provided data that can be utilized in clinical settings. Methods This was a nonrandomised controlled experimental study. Participants included lucid adult patients who were admitted to the intensive care unit and had spent more than two nights there. The experimental treatment required participants to engage in deep breathing with essential oils as part of the aromatherapy. The control group was instructed to go to sleep without receiving the lavender aroma oil. Results The experimental group and control group showed a significant difference in perceived stress (F = 60.11, p < .001), objective stress index (F = 25.65, p < .001), systolic blood pressure (F = 9.09, p < .001), diastolic blood pressure (F = 2.47, p = .046), heart rate (F = 5.71, p < .001), and sleep quality (F = 109.46, p < .001). Conclusions The results revealed that aromatherapy alleviated stress and improved sleep quality in intensive care unit patients after 2 days of the experimental treatment. These results demonstrate that aromatherapy affects stress and sleep quality, thus indicating its value in nursing interventions. This trial is registered with KCT0002344. PMID:29375641

Agent-based station for on-line diagnostics by self-adaptive laser Doppler vibrometry

NASA Astrophysics Data System (ADS)

Serafini, S.; Paone, N.; Castellini, P.

2013-12-01

A self-adaptive diagnostic system based on laser vibrometry is proposed for quality control of mechanical defects by vibration testing; it is developed for appliances at the end of an assembly line, but its characteristics are generally suited for testing most types of electromechanical products. It consists of a laser Doppler vibrometer, equipped with scanning mirrors and a camera, which implements self-adaptive bahaviour for optimizing the measurement. The system is conceived as a Quality Control Agent (QCA) and it is part of a Multi Agent System that supervises all the production line. The QCA behaviour is defined so to minimize measurement uncertainty during the on-line tests and to compensate target mis-positioning under guidance of a vision system. Best measurement conditions are reached by maximizing the amplitude of the optical Doppler beat signal (signal quality) and consequently minimize uncertainty. In this paper, the optimization strategy for measurement enhancement achieved by the down-hill algorithm (Nelder-Mead algorithm) and its effect on signal quality improvement is discussed. Tests on a washing machine in controlled operating conditions allow to evaluate the efficacy of the method; significant reduction of noise on vibration velocity spectra is observed. Results from on-line tests are presented, which demonstrate the potential of the system for industrial quality control.

Kanawha River Basin Water Quality Modeling

DTIC Science & Technology

1986-07-01

was performed by Mr. R. G. Willey with the technical assistance of Mr. Keith Knight. Mr. Don Smith of Resource Management Associates provided advice...during critical parts of the study. The study was managed under the direcLion of Dr. Richard Punnett of the Huntington District who was also responsible...to provide better system water quality analysis capabilities in support of the Corps’ water control management program. The focus of this program is

Quality Control and Nondestructive Evaluation Techniques for Composites. Part 1. Overview of Characterization Techniques for Composite Reliability

DTIC Science & Technology

1982-05-01

MONITORING AND MANAGEMENT , 34 7.0 NONDESTRUCTIVE EVALUATION ( NDE ) 37 8. 0 SURFACE NDE 44 9.0 PERFORMANCE AND PROOF TESTING 46 10.0 SUMMARY AND...Chemical Quality Assurance Testing 2. Processability Testing 3. Cure Monitoring and Management 4. Nondestructive Evaluation ( NDE ) 5. Performance and...the management concept for implementing the specific tests. Chemical analysis, nondestructive evaluation ( NDE ) and environmental fatigue testing of

Standard Reference Specimens in Quality Control of Engineering Surfaces

PubMed Central

Song, J. F.; Vorburger, T. V.

1991-01-01

In the quality control of engineering surfaces, we aim to understand and maintain a good relationship between the manufacturing process and surface function. This is achieved by controlling the surface texture. The control process involves: 1) learning the functional parameters and their control values through controlled experiments or through a long history of production and use; 2) maintaining high accuracy and reproducibility with measurements not only of roughness calibration specimens but also of real engineering parts. In this paper, the characteristics, utilizations, and limitations of different classes of precision roughness calibration specimens are described. A measuring procedure of engineering surfaces, based on the calibration procedure of roughness specimens at NIST, is proposed. This procedure involves utilization of check specimens with waveform, wavelength, and other roughness parameters similar to functioning engineering surfaces. These check specimens would be certified under standardized reference measuring conditions, or by a reference instrument, and could be used for overall checking of the measuring procedure and for maintaining accuracy and agreement in engineering surface measurement. The concept of “surface texture design” is also suggested, which involves designing the engineering surface texture, the manufacturing process, and the quality control procedure to meet the optimal functional needs. PMID:28184115

[The external evaluation of study quality: the role in maintaining the reliability of laboratory information].

PubMed

Men'shikov, V V

2013-08-01

The external evaluation of quality of clinical laboratory examinations was gradually introduced in USSR medical laboratories since 1970s. In Russia, in the middle of 1990 a unified all-national system of external evaluation quality was organized known as the Federal center of external evaluation of quality at the basis of laboratory of the state research center of preventive medicine. The main positions of policy in this area were neatly formulated in the guidance documents of ministry of Health. Nowadays, the center of external evaluation of quality proposes 100 and more types of control studies and permanently extends their specter starting from interests of different disciplines of clinical medicine. The consistent participation of laboratories in the cycles of external evaluation of quality intrinsically promotes improvement of indicators of properness and precision of analysis results and increases reliability of laboratory information. However, a significant percentage of laboratories does not participate at all in external evaluation of quality or takes part in control process irregularly and in limited number of tests. The managers of a number of medical organizations disregard the application of the proposed possibilities to increase reliability of laboratory information and limit financing of studies in the field of quality control. The article proposes to adopt the national standard on the basis of ISO 17043 "Evaluation of compliance. The common requirements of professional competence testing".

EMISSIONS PROFILE CHARACTERIZATION OF LAKE MICHIGAN POLLUTANT SOURCES - PART III

EPA Science Inventory

The southern Lake Michigan aea continues to experience poor air quality despite the implementation of many measures to control particulate matter, ozone and toxic pollutants. Fortunately, the ambient atmosphere holds clues to these sources and their contributions to urban polluti...

EMISSIONS PROFILE CHARACTERIZATION OF LAKE MICHIGAN POLLUTANT SOURCES - PART II

EPA Science Inventory

The southern Lake Michigan area continues to experience poor air quality despite the implementation of many measures to control particulate matter, ozone and toxic pollutants. Fortunately, the ambient atmosphere holds clues to these sources and their contributions to urban pollut...

Air Pollution Surveillance Systems

ERIC Educational Resources Information Center

Morgan, George B.; And Others

1970-01-01

Describes atmospheric data monitoring as part of total airpollution control effort. Summarizes types of gaseous, liquid and solid pollutants and their sources; contrast between urban and rural environmental air quality; instrumentation to identify pollutants; and anticipated new non-wet chemical physical and physiochemical techniques tor cetection…

BATHING BEACH MONITORING PROTOCOLS/COMMUNICATING SWIMMING ACTIVITY RISK TO THE PUBLIC

EPA Science Inventory

Current Environmental Protection Agency (EPA) recommended monitoring practices for bathing beach water quality were suggested in 1968, as a part of the fecal coliform guideline developed by the Federal Water Pollution Control Administration. The guideline stated that five water ...

77 FR 4901 - Designation of Areas for Air Quality Planning Purposes; Maryland; Determination of Nonattainment...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-01

... who are active outdoors, and individuals with a pre-existing respiratory disease, such as asthma. On... requirements. (See section 307(b)(2).) List of Subjects in 40 CFR Part 81 Air pollution control, National parks...

System of GIS-Based Hydrologic and Hydraulic Applications for Highway Engineering: Summary Report

DOT National Transportation Integrated Search

1999-10-01

A significant part of the cost of most highway projects is attributable to drainage facilities, such as bridges, highway culverts, storm drains, and water quality and quantity control structures. Design of these facilities involves a hydrologic analy...

Process monitoring of additive manufacturing by using optical tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zenzinger, Guenter, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Bamberg, Joachim, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Ladewig, Alexander, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de

2015-03-31

Parts fabricated by means of additive manufacturing are usually of complex shape and owing to the fabrication procedure by using selective laser melting (SLM), potential defects and inaccuracies are often very small in lateral size. Therefore, an adequate quality inspection of such parts is rather challenging, while non-destructive-techniques (NDT) are difficult to realize, but considerable efforts are necessary in order to ensure the quality of SLM-parts especially used for aerospace components. Thus, MTU Aero Engines is currently focusing on the development of an Online Process Control system which monitors and documents the complete welding process during the SLM fabrication procedure.more » A high-resolution camera system is used to obtain images, from which tomographic data for a 3dim analysis of SLM-parts are processed. From the analysis, structural irregularities and structural disorder resulting from any possible erroneous melting process become visible and may be allocated anywhere within the 3dim structure. Results of our optical tomography (OT) method as obtained on real defects are presented.« less

Controlled by Love: The Harmful Relational Consequences of Perceived Conditional Positive Regard.

PubMed

Kanat-Maymon, Yaniv; Roth, Guy; Assor, Avi; Raizer, Abira

2016-08-01

Research on conditional positive regard (CPR) has shown that this seemingly benign practice has maladaptive correlates when used by parents. However, there is no research on the correlates of this practice in romantic relationships or on the processes mediating its effects. Building on self-determination theory (Deci & Ryan, ), three studies tested the hypothesis that perceived CPR impairs relationship quality, partly because it undermines the fulfillment of the basic psychological needs for autonomy and relatedness. Study 1 (N = 125) examined perceived CPR and relationship quality across four relationship targets: mother, father, romantic partner, and best friend. Study 2, involving romantic partners (N = 142), examined whether needs fulfillment mediated the association between perceived CPR and relationship quality. Study 3, involving romantic dyads (N = 85), also included partner reports on CPR. Across the three studies, CPR was linked with poor relationship quality between relationships, between people, and between dyadic partners. Moreover, results of Study 2 and Study 3 revealed that the inverse association between perceived CPR and relationship quality was mediated by dissatisfaction of autonomy but not relatedness. Despite its seemingly benign nature, CPR is detrimental to relationship quality, partly because it thwarts the basic need for autonomy. © 2015 Wiley Periodicals, Inc.

A global reference database of crowdsourced cropland data collected using the Geo-Wiki platform.

PubMed

Laso Bayas, Juan Carlos; Lesiv, Myroslava; Waldner, François; Schucknecht, Anne; Duerauer, Martina; See, Linda; Fritz, Steffen; Fraisl, Dilek; Moorthy, Inian; McCallum, Ian; Perger, Christoph; Danylo, Olha; Defourny, Pierre; Gallego, Javier; Gilliams, Sven; Akhtar, Ibrar Ul Hassan; Baishya, Swarup Jyoti; Baruah, Mrinal; Bungnamei, Khangsembou; Campos, Alfredo; Changkakati, Trishna; Cipriani, Anna; Das, Krishna; Das, Keemee; Das, Inamani; Davis, Kyle Frankel; Hazarika, Purabi; Johnson, Brian Alan; Malek, Ziga; Molinari, Monia Elisa; Panging, Kripal; Pawe, Chandra Kant; Pérez-Hoyos, Ana; Sahariah, Parag Kumar; Sahariah, Dhrubajyoti; Saikia, Anup; Saikia, Meghna; Schlesinger, Peter; Seidacaru, Elena; Singha, Kuleswar; Wilson, John W

2017-09-26

A global reference data set on cropland was collected through a crowdsourcing campaign using the Geo-Wiki crowdsourcing tool. The campaign lasted three weeks, with over 80 participants from around the world reviewing almost 36,000 sample units, focussing on cropland identification. For quality assessment purposes, two additional data sets are provided. The first is a control set of 1,793 sample locations validated by students trained in satellite image interpretation. This data set was used to assess the quality of the crowd as the campaign progressed. The second data set contains 60 expert validations for additional evaluation of the quality of the contributions. All data sets are split into two parts: the first part shows all areas classified as cropland and the second part shows cropland average per location and user. After further processing, the data presented here might be suitable to validate and compare medium and high resolution cropland maps generated using remote sensing. These could also be used to train classification algorithms for developing new maps of land cover and cropland extent.

Research of the Quality of Quarry Dumpers Engine Crankshafts Sliding Bearings of Various Manufacturers

NASA Astrophysics Data System (ADS)

Korotkov, Alexander; Korotkova, Lidiya; Vidin, Denis

2017-11-01

Sliding bearings are an important part of many large and critical components. They are widely used in power equipment, high-capacity pumps, compressors, electric motors and internal combustion engines (ICE). As a rule, sliding bearings include an antifriction bushing, part of the shaft surface (bearing journal), and a layer of oil between them. These are complex and critical parts in which there may occur dangerous defects, and which directly affect the durability, accuracy and reliability of the entire unit. To ensure high reliability of the equipment with sliding bearings applied in complex equipment, it is necessary to provide the quality control and sufficient level of monitoring of the technical condition, as well as diagnosis of emerging defects. This paper presents a comparative analysis of the internal combustion engines sliding bearings quality of various manufacturing companies. It gives operational properties of bearings depending on the compositional composition. The results of chemical analysis of the base, the cover and intermediate layers of the ICE liners are presented here. We have also made recommendations to increase the operational performance of sliding bearings.

A global reference database of crowdsourced cropland data collected using the Geo-Wiki platform

PubMed Central

Laso Bayas, Juan Carlos; Lesiv, Myroslava; Waldner, François; Schucknecht, Anne; Duerauer, Martina; See, Linda; Fritz, Steffen; Fraisl, Dilek; Moorthy, Inian; McCallum, Ian; Perger, Christoph; Danylo, Olha; Defourny, Pierre; Gallego, Javier; Gilliams, Sven; Akhtar, Ibrar ul Hassan; Baishya, Swarup Jyoti; Baruah, Mrinal; Bungnamei, Khangsembou; Campos, Alfredo; Changkakati, Trishna; Cipriani, Anna; Das, Krishna; Das, Keemee; Das, Inamani; Davis, Kyle Frankel; Hazarika, Purabi; Johnson, Brian Alan; Malek, Ziga; Molinari, Monia Elisa; Panging, Kripal; Pawe, Chandra Kant; Pérez-Hoyos, Ana; Sahariah, Parag Kumar; Sahariah, Dhrubajyoti; Saikia, Anup; Saikia, Meghna; Schlesinger, Peter; Seidacaru, Elena; Singha, Kuleswar; Wilson, John W

2017-01-01

A global reference data set on cropland was collected through a crowdsourcing campaign using the Geo-Wiki crowdsourcing tool. The campaign lasted three weeks, with over 80 participants from around the world reviewing almost 36,000 sample units, focussing on cropland identification. For quality assessment purposes, two additional data sets are provided. The first is a control set of 1,793 sample locations validated by students trained in satellite image interpretation. This data set was used to assess the quality of the crowd as the campaign progressed. The second data set contains 60 expert validations for additional evaluation of the quality of the contributions. All data sets are split into two parts: the first part shows all areas classified as cropland and the second part shows cropland average per location and user. After further processing, the data presented here might be suitable to validate and compare medium and high resolution cropland maps generated using remote sensing. These could also be used to train classification algorithms for developing new maps of land cover and cropland extent. PMID:28949323

A global reference database of crowdsourced cropland data collected using the Geo-Wiki platform

NASA Astrophysics Data System (ADS)

Laso Bayas, Juan Carlos; Lesiv, Myroslava; Waldner, François; Schucknecht, Anne; Duerauer, Martina; See, Linda; Fritz, Steffen; Fraisl, Dilek; Moorthy, Inian; McCallum, Ian; Perger, Christoph; Danylo, Olha; Defourny, Pierre; Gallego, Javier; Gilliams, Sven; Akhtar, Ibrar Ul Hassan; Baishya, Swarup Jyoti; Baruah, Mrinal; Bungnamei, Khangsembou; Campos, Alfredo; Changkakati, Trishna; Cipriani, Anna; Das, Krishna; Das, Keemee; Das, Inamani; Davis, Kyle Frankel; Hazarika, Purabi; Johnson, Brian Alan; Malek, Ziga; Molinari, Monia Elisa; Panging, Kripal; Pawe, Chandra Kant; Pérez-Hoyos, Ana; Sahariah, Parag Kumar; Sahariah, Dhrubajyoti; Saikia, Anup; Saikia, Meghna; Schlesinger, Peter; Seidacaru, Elena; Singha, Kuleswar; Wilson, John W.

2017-09-01

A global reference data set on cropland was collected through a crowdsourcing campaign using the Geo-Wiki crowdsourcing tool. The campaign lasted three weeks, with over 80 participants from around the world reviewing almost 36,000 sample units, focussing on cropland identification. For quality assessment purposes, two additional data sets are provided. The first is a control set of 1,793 sample locations validated by students trained in satellite image interpretation. This data set was used to assess the quality of the crowd as the campaign progressed. The second data set contains 60 expert validations for additional evaluation of the quality of the contributions. All data sets are split into two parts: the first part shows all areas classified as cropland and the second part shows cropland average per location and user. After further processing, the data presented here might be suitable to validate and compare medium and high resolution cropland maps generated using remote sensing. These could also be used to train classification algorithms for developing new maps of land cover and cropland extent.

Automated batch characterization of inkjet-printed elastomer lenses using a LEGO platform.

PubMed

Sung, Yu-Lung; Garan, Jacob; Nguyen, Hoang; Hu, Zhenyu; Shih, Wei-Chuan

2017-09-10

Small, self-adhesive, inkjet-printed elastomer lenses have enabled smartphone cameras to image and resolve microscopic objects. However, the performance of different lenses within a batch is affected by hard-to-control environmental variables. We present a cost-effective platform to perform automated batch characterization of 300 lens units simultaneously for quality inspection. The system was designed and configured with LEGO bricks, 3D printed parts, and a digital camera. The scheme presented here may become the basis of a high-throughput, in-line inspection tool for quality control purposes and can also be employed for optimization of the manufacturing process.

The Strange Death of Number Controls in England: Paradoxical Adventures in Higher Education Market Making

ERIC Educational Resources Information Center

McCaig, Colin; Taylor, Carol

2017-01-01

The paper analyses the impact of a higher education (HE) funding mechanism, the "High Grades" policy, introduced as part of a student number control regime in England that was introduced in 2012/13 and withdrawn after only two years. This marked the end of an experiment in market making based on quality and price within a fixed student…

Management approach recommendations. Earth Observatory Satellite system definition study (EOS)

NASA Technical Reports Server (NTRS)

1974-01-01

Management analyses and tradeoffs were performed to determine the most cost effective management approach for the Earth Observatory Satellite (EOS) Phase C/D. The basic objectives of the management approach are identified. Some of the subjects considered are as follows: (1) contract startup phase, (2) project management control system, (3) configuration management, (4) quality control and reliability engineering requirements, and (5) the parts procurement program.

[Multi-central controlled study on three-part massage therapy for treatment of insomnia of deficiency of both the heart and spleen].

PubMed

Zhou, Yun-feng; Wei, Yu-long; Zhang, Pu-lin; Gao, Shan; Ning, Guo-li; Zhang, Zhen-qiang; Hu, Bin; Wang, Dan-yi; Yan, Mei-rong; Liu, Wen-jun

2006-06-01

To make multi-central clinical evaluation for three-part massage therapy for treatment of insomnia of deficiency of both the heart and spleen. One hundred and sixty-six cases were randomly divided into a test group (n = 84) and a control group (n = 82). Multi-central, randomized and controlled methods were adopted. The test group were treated by the three-part massage therapy, i. e. acupoints at the head, abdomen and back were massaged, once each day; and the control group by oral administration of Guipi Pills [symbol: see text], 8 pills each time, thrice daily. The treatment was given for 15 consecutive days and then the therapeutic effects were observed. Sixty-seven cases were cured, 11 markedly effective, 3 effective, and 3 ineffective in the test group, and the corresponding figures were 10, 21, 29 and 22 in the control group with a very significant difference between the two groups (P< 0.001). The test group was superior to the control group in improvement for Pittsburgh Sleep Quality Index (PSQI), Sleepless Anxiety Scale (SAS) and Sleepless Depression Scale (SDS) (P < 0.001). The three-part massage therapy has definite therapeutic effect on insomnia of deficiency of both the heart and spleen with safety.

In vitro evaluation of Augmentin by broth microdilution and disk diffusion susceptibility testing: regression analysis, tentative interpretive criteria, and quality control limits.

PubMed Central

Fuchs, P C; Barry, A L; Thornsberry, C; Gavan, T L; Jones, R N

1983-01-01

Augmentin (Beecham Laboratories, Bristol, Tenn.), a combination drug consisting of two parts amoxicillin to one part clavulanic acid and a potent beta-lactamase inhibitor, was evaluated in vitro in comparison with ampicillin or amoxicillin or both for its inhibitory and bactericidal activities against selected clinical isolates. Regression analysis was performed and tentative disk diffusion susceptibility breakpoints were determined. A multicenter performance study of the disk diffusion test was conducted with three quality control organisms to determine tentative quality control limits. All methicillin-susceptible staphylococci and Haemophilus influenzae isolates were susceptible to Augmentin, although the minimal inhibitory concentrations for beta-lactamase-producing strains of both groups were, on the average, fourfold higher than those for enzyme-negative strains. Among the Enterobacteriaceae, Augmentin exhibited significantly greater activity than did ampicillin against Klebsiella pneumoniae, Citrobacter diversus, Proteus vulgaris, and about one-third of the Escherichia coli strains tested. Bactericidal activity usually occurred at the minimal inhibitory concentration. There was a slight inoculum concentration effect on the Augmentin minimal inhibitory concentrations. On the basis of regression and error rate-bounded analyses, the suggested interpretive disk diffusion susceptibility breakpoints for Augmentin are: susceptible, greater than or equal to 18 mm; resistant, less than or equal to 13 mm (gram-negative bacilli); and susceptible, greater than or equal to 20 mm (staphylococci and H. influenzae). The use of a beta-lactamase-producing organism, such as E. coli Beecham 1532, is recommended for quality assurance of Augmentin susceptibility testing. PMID:6625554

Electronic Reliability Design Handbook. Volume 1

DTIC Science & Technology

1988-10-12

greater use of proven designs , more design attention to non -random failures, design sim- plicity, improved quality control , more effective development and...RELIABILITY ENGINEERING DESIGN GUIDELINES 7-1 7.1 INTRODUCTION 7-1 7.2 PART SELECTION AND CONTROL 7-1 7.3 DERATING 7-4 7.3.1 DERATING OF MECHANICAL STRUCTURAL...11-58 11.3.1 INTRODUCTION 11-58 11.3.2 MAINTAINABILITY DESIGN ATTRIBUTES 11-59 11.3.3 MAINTAINABILITY CONTROL PARAMETERS 11-59 11.3.4 MAINTAINABILITY

Epidemiology and quality assurance: applications at farm level.

PubMed

Noordhuizen, J P; Frankena, K

1999-03-29

Animal production is relevant with respect to farm income and the position of the sector in the market, but also with respect to the quality and safety of products of animal origin, related to public health. Animal production is part of a chain of food production. Therefore, producers have to take consumer expectations and demands in the domains of animal health, welfare and environment into account. A different attitude for production has to be adopted; this attitude can be visualized in good farming practice, GFP, codes. Farmers who focused on quality in its broadest sense need a system supporting them in their management and control of quality risks. Generally speaking, there are three systems for that purpose: GFP, ISO and HACCP. When the hypothesis followed relates to animal health being a feature of quality, or else welfare and environmental issues, then animal health care can be executed following quality control principles. The HACCP concept is well suited for quality control at farm level, involving risk identification and risk management. The on-farm monitoring and surveillance system of critical control points in the animal production process is the most important tool in this procedure. Principles for HACCP application as well as certification fitness of HACCP are elaborated upon. They are illustrated by using salmonellosis in meat-pig farms as objective for an HACCP approach. It is further discussed that, in addition to animal health and quality, animal welfare and environmental issues could also be covered by an HACCP-like system in an integrated manner. Ultimately, the HACCP modules could end up in an overall ISO certification.

Quality Controlling CMIP datasets at GFDL

NASA Astrophysics Data System (ADS)

Horowitz, L. W.; Radhakrishnan, A.; Balaji, V.; Adcroft, A.; Krasting, J. P.; Nikonov, S.; Mason, E. E.; Schweitzer, R.; Nadeau, D.

2017-12-01

As GFDL makes the switch from model development to production in light of the Climate Model Intercomparison Project (CMIP), GFDL's efforts are shifted to testing and more importantly establishing guidelines and protocols for Quality Controlling and semi-automated data publishing. Every CMIP cycle introduces key challenges and the upcoming CMIP6 is no exception. The new CMIP experimental design comprises of multiple MIPs facilitating research in different focus areas. This paradigm has implications not only for the groups that develop the models and conduct the runs, but also for the groups that monitor, analyze and quality control the datasets before data publishing, before their knowledge makes its way into reports like the IPCC (Intergovernmental Panel on Climate Change) Assessment Reports. In this talk, we discuss some of the paths taken at GFDL to quality control the CMIP-ready datasets including: Jupyter notebooks, PrePARE, LAMP (Linux, Apache, MySQL, PHP/Python/Perl): technology-driven tracker system to monitor the status of experiments qualitatively and quantitatively, provide additional metadata and analysis services along with some in-built controlled-vocabulary validations in the workflow. In addition to this, we also discuss the integration of community-based model evaluation software (ESMValTool, PCMDI Metrics Package, and ILAMB) as part of our CMIP6 workflow.

Likelihood of achieving air quality targets under model uncertainties.

PubMed

Digar, Antara; Cohan, Daniel S; Cox, Dennis D; Kim, Byeong-Uk; Boylan, James W

2011-01-01

Regulatory attainment demonstrations in the United States typically apply a bright-line test to predict whether a control strategy is sufficient to attain an air quality standard. Photochemical models are the best tools available to project future pollutant levels and are a critical part of regulatory attainment demonstrations. However, because photochemical models are uncertain and future meteorology is unknowable, future pollutant levels cannot be predicted perfectly and attainment cannot be guaranteed. This paper introduces a computationally efficient methodology for estimating the likelihood that an emission control strategy will achieve an air quality objective in light of uncertainties in photochemical model input parameters (e.g., uncertain emission and reaction rates, deposition velocities, and boundary conditions). The method incorporates Monte Carlo simulations of a reduced form model representing pollutant-precursor response under parametric uncertainty to probabilistically predict the improvement in air quality due to emission control. The method is applied to recent 8-h ozone attainment modeling for Atlanta, Georgia, to assess the likelihood that additional controls would achieve fixed (well-defined) or flexible (due to meteorological variability and uncertain emission trends) targets of air pollution reduction. The results show that in certain instances ranking of the predicted effectiveness of control strategies may differ between probabilistic and deterministic analyses.

3D Printing, Additive Manufacturing, and Solid Freeform Fabrication: The Technologies of the Past, Present and Future

NASA Astrophysics Data System (ADS)

Beaman, Joseph

2015-03-01

Starting in the late 1980's, several new technologies were created that have the potential to revolutionize manufacturing. These technologies are, for the most part, additive processes that build up parts layer by layer. In addition, the processes that are being touted for hard-core manufacturing are primarily laser or e-beam based processes. This presentation gives a brief history of Additive Manufacturing and gives an assessment for these technologies. These technologies initially grew out of a commercial need for rapid prototyping. This market has a different requirement for process and quality control than traditional manufacturing. The relatively poor process control of the existing commercial Additive Manufacturing equipment is a vestige of this history. This presentation discusses this history and improvements in quality over time. The emphasis will be on Additive Manufacturing processes that are being considered for direct manufacturing, which is a different market than the 3D Printing ``Makerbot'' market. Topics discussed include past and present machine sensors, materials, and operational methods that were used in the past and those that are used today to create manufactured parts. Finally, a discussion of new methods and future directions of AM is presented.

User Interaction with the CNPC Link

NASA Technical Reports Server (NTRS)

Hobbs, Alan; Lyall, Elizabeth A.

2014-01-01

As part of NASAs UAS in the NAS project, human factor guidelines are being developed for the ground control station of unmanned aircraft systems. A critical task for the pilot of a UAS is the management and control of the terrestrial radio links used to provide control of the vehicle and relay communications with air traffic control. An analysis of the task of the UAS pilot has been conducted to identify areas where guidelines are required. This analysis has identified a set of information requirements that must be supported by the radio equipment used to provide Control and Non-payload Communication (CNPC). Key requirements include the need for an alert when the link is lost, information on the current quality and latency of the link, and information to enable the future quality of the link to be anticipated as the aircraft changes location. These identified requirements can assist in the development of minimum operational performance standards for CNPC equipment.

Quality status display for a vibration welding process

DOEpatents

Spicer, John Patrick; Abell, Jeffrey A.; Wincek, Michael Anthony; Chakraborty, Debejyo; Bracey, Jennifer; Wang, Hui; Tavora, Peter W.; Davis, Jeffrey S.; Hutchinson, Daniel C.; Reardon, Ronald L.; Utz, Shawn

2017-03-28

A system includes a host machine and a status projector. The host machine is in electrical communication with a collection of sensors and with a welding controller that generates control signals for controlling the welding horn. The host machine is configured to execute a method to thereby process the sensory and control signals, as well as predict a quality status of a weld that is formed using the welding horn, including identifying any suspect welds. The host machine then activates the status projector to illuminate the suspect welds. This may occur directly on the welds using a laser projector, or on a surface of the work piece in proximity to the welds. The system and method may be used in the ultrasonic welding of battery tabs of a multi-cell battery pack in a particular embodiment. The welding horn and welding controller may also be part of the system.

Regulation of assimilate partitioning by daylength and spectral quality

NASA Technical Reports Server (NTRS)

Britz, Steve J.

1994-01-01

The effects of daylength and spectral quality on assimilate partitioning and leaf carbohydrate content should be considered when conducting controlled environment experiments or comparing results between studies obtained under different lighting conditions. Changes in partitioning may indicate alterations to photoregulatory processes within the source leaf rather than disruptions in sink strength. Moreover, it may be possible to use photoregulatory responses of assimilate partitioning to probe mechanisms of growth and development involving translocation of carbon or adaptation to environmental factors such as elevated CO2. It may also be possible to steer assimilate partitioning for the benefit of controlled environment agriculture using energy-efficient manipulations such as daylength extensions with dim irradiances, end-of-day alterations in light quality, or shifting plants between different spectral qualities as a part of phasic control of growth and development. Note that high starch levels measured on a one-time basis provide little information, since it is the proportion of photosynthate stored as starch that is meaningful. Large differences in starch content can result from small changes in partitioning integrated over several days. Rate information is required.

Spatial Data Quality Control Procedure applied to the Okavango Basin Information System

NASA Astrophysics Data System (ADS)

Butchart-Kuhlmann, Daniel

2014-05-01

Spatial data is a powerful form of information, capable of providing information of great interest and tremendous use to a variety of users. However, much like other data representing the 'real world', precision and accuracy must be high for the results of data analysis to be deemed reliable and thus applicable to real world projects and undertakings. The spatial data quality control (QC) procedure presented here was developed as the topic of a Master's thesis, in the sphere of and using data from the Okavango Basin Information System (OBIS), itself a part of The Future Okavango (TFO) project. The aim of the QC procedure was to form the basis of a method through which to determine the quality of spatial data relevant for application to hydrological, solute, and erosion transport modelling using the Jena Adaptable Modelling System (JAMS). As such, the quality of all data present in OBIS classified under the topics of elevation, geoscientific information, or inland waters, was evaluated. Since the initial data quality has been evaluated, efforts are underway to correct the errors found, thus improving the quality of the dataset.

Effect of steel structure and defects on reliability of parts of impact mechanisms

NASA Astrophysics Data System (ADS)

Popelyukh, AI; Repin, AA; Alekseev, SE

2018-03-01

The paper discusses selection of materials suitable for manufacturing critical parts of impact mechanisms. It is shown that in order to extend life of parts exposed to high dynamic loading, it is expedient to use medium- and high-carbon alloy-treated steels featuring low impurity with nonmetallic inclusions and high hardening characteristics. Application of thermally untreated parts is undesirable as steel having ferrite–pearlite structure possesses low fatigue strength. Aimed to ensure high reliability of parts with a hardness of 42–55 HRC, steel should be reinforced by thermal treatement with the formation of multicomponent martensite–bainite structure. High-quality production should include defectoscopy and incoming material control.

Incorporating Handling Qualities Analysis into Rotorcraft Conceptual Design

NASA Technical Reports Server (NTRS)

Lawrence, Ben

2014-01-01

This paper describes the initial development of a framework to incorporate handling qualities analyses into a rotorcraft conceptual design process. In particular, the paper describes how rotorcraft conceptual design level data can be used to generate flight dynamics models for handling qualities analyses. Also, methods are described that couple a basic stability augmentation system to the rotorcraft flight dynamics model to extend analysis to beyond that of the bare airframe. A methodology for calculating the handling qualities characteristics of the flight dynamics models and for comparing the results to ADS-33E criteria is described. Preliminary results from the application of the handling qualities analysis for variations in key rotorcraft design parameters of main rotor radius, blade chord, hub stiffness and flap moment of inertia are shown. Varying relationships, with counteracting trends for different handling qualities criteria and different flight speeds are exhibited, with the action of the control system playing a complex part in the outcomes. Overall, the paper demonstrates how a broad array of technical issues across flight dynamics stability and control, simulation and modeling, control law design and handling qualities testing and evaluation had to be confronted to implement even a moderately comprehensive handling qualities analysis of relatively low fidelity models. A key outstanding issue is to how to 'close the loop' with an overall design process, and options for the exploration of how to feedback handling qualities results to a conceptual design process are proposed for future work.

Statistical Methods in Assembly Quality Management of Multi-Element Products on Automatic Rotor Lines

NASA Astrophysics Data System (ADS)

Pries, V. V.; Proskuriakov, N. E.

2018-04-01

To control the assembly quality of multi-element mass-produced products on automatic rotor lines, control methods with operational feedback are required. However, due to possible failures in the operation of the devices and systems of automatic rotor line, there is always a real probability of getting defective (incomplete) products into the output process stream. Therefore, a continuous sampling control of the products completeness, based on the use of statistical methods, remains an important element in managing the quality of assembly of multi-element mass products on automatic rotor lines. The feature of continuous sampling control of the multi-element products completeness in the assembly process is its breaking sort, which excludes the possibility of returning component parts after sampling control to the process stream and leads to a decrease in the actual productivity of the assembly equipment. Therefore, the use of statistical procedures for continuous sampling control of the multi-element products completeness when assembled on automatic rotor lines requires the use of such sampling plans that ensure a minimum size of control samples. Comparison of the values of the limit of the average output defect level for the continuous sampling plan (CSP) and for the automated continuous sampling plan (ACSP) shows the possibility of providing lower limit values for the average output defects level using the ACSP-1. Also, the average sample size when using the ACSP-1 plan is less than when using the CSP-1 plan. Thus, the application of statistical methods in the assembly quality management of multi-element products on automatic rotor lines, involving the use of proposed plans and methods for continuous selective control, will allow to automating sampling control procedures and the required level of quality of assembled products while minimizing sample size.

Methods for collecting algal samples as part of the National Water-Quality Assessment Program

USGS Publications Warehouse

Porter, Stephen D.; Cuffney, Thomas F.; Gurtz, Martin E.; Meador, Michael R.

1993-01-01

Benthic algae (periphyton) and phytoplankton communities are characterized in the U.S. Geological Survey's National Water-Quality Assessment Program as part of an integrated physical, chemical, and biological assessment of the Nation's water quality. This multidisciplinary approach provides multiple lines of evidence for evaluating water-quality status and trends, and for refining an understanding of the factors that affect water-quality conditions locally, regionally, and nationally. Water quality can be characterized by evaluating the results of qualitative and quantitative measurements of the algal community. Qualitative periphyton samples are collected to develop of list of taxa present in the sampling reach. Quantitative periphyton samples are collected to measure algal community structure within selected habitats. These samples of benthic algal communities are collected from natural substrates, using the sampling methods that are most appropriate for the habitat conditions. Phytoplankton samples may be collected in large nonwadeable streams and rivers to meet specific program objectives. Estimates of algal biomass (chlorophyll content and ash-free dry mass) also are optional measures that may be useful for interpreting water-quality conditions. A nationally consistent approach provides guidance on site, reach, and habitat selection, as well as information on methods and equipment for qualitative and quantitative sampling. Appropriate quality-assurance and quality-control guidelines are used to maximize the ability to analyze data locally, regionally, and nationally.

21 CFR 886.1870 - Stereoscope.

Code of Federal Regulations, 2012 CFR

2012-04-01

...-dimensional appearance of solidity and relief. It is intended to measure the angle of strabismus (eye muscle... exercises of eye muscles. (b) Classification. Class I (general controls). The AC-powered device and the... current good manufacturing practice requirements of the quality system regulation in part 820 of this...

21 CFR 886.1870 - Stereoscope.

Code of Federal Regulations, 2014 CFR

2014-04-01

...-dimensional appearance of solidity and relief. It is intended to measure the angle of strabismus (eye muscle... exercises of eye muscles. (b) Classification. Class I (general controls). The AC-powered device and the... current good manufacturing practice requirements of the quality system regulation in part 820 of this...

21 CFR 886.1870 - Stereoscope.

Code of Federal Regulations, 2013 CFR

2013-04-01

...-dimensional appearance of solidity and relief. It is intended to measure the angle of strabismus (eye muscle... exercises of eye muscles. (b) Classification. Class I (general controls). The AC-powered device and the... current good manufacturing practice requirements of the quality system regulation in part 820 of this...

ENVIRONMENTAL MONITORING FOR PUBLIC ACCESS AND COMMUNITY TRACKING (EMPACT) PROGRAM MICROBIOLOGICAL MONITORING OF RECREATIONAL WATER

EPA Science Inventory

Current Environmental Protection Agency (EPA) recommended microbiological monitoring practices for bathing beach water quality were suggested in 1968, as a part of the fecal coliform guideline developed by the Federal Water Pollution Control Administration. The guideline stated ...

Nondestructive testing of railroad wheels and rails by ultrasonics

NASA Technical Reports Server (NTRS)

Clotfelter, W. M.; Risch, E. R.

1974-01-01

Quality control of wheels and rails can be improved by using ultrasonic technique developed for measuring stresses in metallic materials. In addition, parts already in use can be tested and replaced if they are found to be unsafe. Test equipment includes two transducers.

Quality control analysis : part IV : field simulation of asphaltic concrete specifications.

DOT National Transportation Integrated Search

1969-02-01

The report present some of the major findings, from a simulated study of statistical specifications, on three asphaltic concrete projects representing a total of approximately 30, 000 tons of hot mix. The major emphasis of the study has been on the a...

Economics of oversized cyclones in the cotton ginning industry

USDA-ARS?s Scientific Manuscript database

Cost of reducing pollution to meet increasingly stringent air quality standards particularly for the U.S. cotton ginning industry is rising overtime. Most industry participants use cyclones to control air pollutants. These cyclones have no moving parts and their initial investment costs are relative...

Effect of process parameters on formability of laser melting deposited 12CrNi2 alloy steel

NASA Astrophysics Data System (ADS)

Peng, Qian; Dong, Shiyun; Kang, Xueliang; Yan, Shixing; Men, Ping

2018-03-01

As a new rapid prototyping technology, the laser melting deposition technology not only has the advantages of fast forming, high efficiency, but also free control in the design and production chain. Therefore, it has drawn extensive attention from community.With the continuous improvement of steel performance requirements, high performance low-carbon alloy steel is gradually integrated into high-tech fields such as aerospace, high-speed train and armored equipment.However, it is necessary to further explore and optimize the difficult process of laser melting deposited alloy steel parts to achieve the performance and shape control.This article took the orthogonal experiment on alloy steel powder by laser melting deposition ,and revealed the influence rule of the laser power, scanning speed, powder gas flow on the quality of the sample than the dilution rate, surface morphology and microstructure analysis were carried out.Finally, under the optimum technological parameters, the Excellent surface quality of the alloy steel forming part with high density, no pore and cracks was obtained.

LC-QTOF-MS Analysis and Activity Profiles of Popular Antioxidant Dietary Supplements in Terms of Quality Control

PubMed Central

Baj, Tomasz; Sawicki, Rafal; Wanat, Aleksandra; Wojtanowski, Krzysztof Kamil; Ginalska, Grazyna; Zgorka, Grazyna; Szymanska, Jolanta

2017-01-01

The dietary supplements with claimed antioxidant activity constitute a substantial part of the dietary supplement market. In this study, we performed the LC-QTOF-MS analysis and investigated the activity profiles of popular antioxidant dietary supplements from different chemical groups in terms of quality control. The commonly used antioxidant tests and statistical analysis revealed that substantial part of the results was comparable if 1 g sample was considered, but while comparing single and daily doses, significant differences in antioxidant values were noticed in all assays. The best antioxidant activity was obtained in ORAC assay (from 142 to 13814 μM of Trolox equivalents per 1 g of sample), and the strongest correlation occurred between TPC and ORAC. The LC-QTOF-MS analysis revealed that catechins were present in samples having the best antioxidant activity and that dietary supplements showing the weakest activity contained very small amount of any chemical constituents. PMID:28642814

Quality: from imperatives to innovations.

PubMed

Dunbar, S

1987-05-01

I have outlined the quality issues facing critical care nurses today and have also presented some challenges for the future. Critical care nurses must now enter a new era characterized by unification, collaboration and involvement, increased professional autonomy, and caring to meet the customer's expectations for quality in fact and quality in perception. Through innovation, critical care nurses can control the pace of change and influence quality in critical care. Recall the kaleidoscope and remember that its intent is to make the whole seem more than the sum of its parts. The image on the horizon is a dynamic and powerful nursing profession as a whole, with critical care nurses assuming an essential and more important role. In fact, the image on the horizon looks bright to me.

Reliability and quality assurance on the MOD 2 wind system

NASA Technical Reports Server (NTRS)

Mason, W. E. B.; Jones, B. G.

1981-01-01

The Safety, Reliability, and Quality Assurance (R&QA) approach developed for the largest wind turbine generator, the Mod 2, is described. The R&QA approach assures that the machine is not hazardous to the public or to the operating personnel, is operated unattended on a utility grid, demonstrates reliable operation, and helps establish the quality assurance and maintainability requirements for future wind turbine projects. The significant guideline consisted of a failure modes and effects analysis (FMEA) during the design phase, hardware inspections during parts fabrication, and three simple documents to control activities during machine construction and operation.

Space Shuttle flying qualities criteria assessment. Phase 5: Data acquistion and analysis

NASA Technical Reports Server (NTRS)

Myers, T. T.; Johnston, D. E.; Mcruer, D. T.

1986-01-01

The development of flying qualities experiments (OFQ) as a part of the Orbiter Experiments Program (OEX) was continued. The data base was extended to use the ground based cinetheodolite measurements of orbiter approach and landing. Onboard the cinetheodolite data were analyzed from flights STS 2 through 7 to identify the effective augmented vehicle dynamics, the control strategy employed by the pilot during preflare, shallow glide, and final flare segments of the landing, and the key approach and touchdown performance measures. A plan for an OFQ flying qualities data archive and processing is presented.

Geochemical evolution processes and water-quality observations based on results of the National Water-Quality Assessment Program in the San Antonio segment of the Edwards aquifer, 1996-2006

USGS Publications Warehouse

Musgrove, MaryLynn; Fahlquist, Lynne; Houston, Natalie A.; Lindgren, Richard J.; Ging, Patricia B.

2010-01-01

As part of the National Water-Quality Assessment Program, the U.S. Geological Survey collected and analyzed groundwater samples during 1996-2006 from the San Antonio segment of the Edwards aquifer of central Texas, a productive karst aquifer developed in Cretaceous-age carbonate rocks. These National Water-Quality Assessment Program studies provide an extensive dataset of groundwater geochemistry and water quality, consisting of 249 groundwater samples collected from 136 sites (wells and springs), including (1) wells completed in the shallow, unconfined, and urbanized part of the aquifer in the vicinity of San Antonio (shallow/urban unconfined category), (2) wells completed in the unconfined (outcrop area) part of the regional aquifer (unconfined category), and (3) wells completed in and springs discharging from the confined part of the regional aquifer (confined category). This report evaluates these data to assess geochemical evolution processes, including local- and regional-scale processes controlling groundwater geochemistry, and to make water-quality observations pertaining to sources and distribution of natural constituents and anthropogenic contaminants, the relation between geochemistry and hydrologic conditions, and groundwater age tracers and travel time. Implications for monitoring water-quality trends in karst are also discussed. Geochemical and isotopic data are useful tracers of recharge, groundwater flow, fluid mixing, and water-rock interaction processes that affect water quality. Sources of dissolved constituents to Edwards aquifer groundwater include dissolution of and geochemical interaction with overlying soils and calcite and dolomite minerals that compose the aquifer. Geochemical tracers such as magnesium to calcium and strontium to calcium ratios and strontium isotope compositions are used to evaluate and constrain progressive fluid-evolution processes. Molar ratios of magnesium to calcium and strontium to calcium in groundwater typically increase along flow paths; results for samples of Edwards aquifer groundwater show an increase from shallow/urban unconfined, to unconfined, to confined groundwater categories. These differences are consistent with longer residence times and greater extents of water-rock interaction controlling fluid compositions as groundwater evolves from shallow unconfined groundwater to deeper confined groundwater. Results for stable isotopes of hydrogen and oxygen indicate specific geochemical processes affect some groundwater samples, including mixing with downdip saline water, mixing with recent recharge associated with tropical cyclonic storms, or mixing with recharge water than has undergone evaporation. The composition of surface water recharging the aquifer, as well as mixing with downdip water from the Trinity aquifer or the saline zone, also might affect water quality. A time-series record (1938-2006) of discharge at Comal Springs, one of the major aquifer discharge points, indicates an upward trend for nitrate and chloride concentrations, which likely reflects anthropogenic activities. A small number of organic contaminants were routinely or frequently detected in Edwards aquifer groundwater samples. These were the pesticides atrazine, its degradate deethylatrazine, and simazine; the drinking-water disinfection byproduct chloroform; and the solvent tetrachloroethene. Detection of these contaminants was most frequent in samples of the shallow/urban unconfined groundwater category and least frequent in samples of the unconfined groundwater category. Results indicate that the shallow/urban unconfined part of the aquifer is most affected by anthropogenic contaminants and the unconfined part of the aquifer is the least affected. The high frequency of detection for these anthropogenic contaminants aquifer-wide and in samples of deep, confined groundwater indicates that the entire aquifer is susceptible to water-quality changes as a result of anthropogenic activities. L

Production of rotational parts in small-series and computer-aided planning of its production engineering

NASA Astrophysics Data System (ADS)

Dudas, Illes; Berta, Miklos; Cser, Istvan

1998-12-01

Up-to-date manufacturing equipments of production of rotational parts in small series are lathe-centers and CNC grinding machines with high concentration of manufacturing operations. By the use of these machine tools it can be produced parts with requirements of increased accuracy and surface quality. In the lathe centers, which contain the manufacturing procedures of lathes using stationary tools and of drilling-milling machine tools using rotational tools, non-rotational surfaces of rotational parts can also be produced. The high concentration of manufacturing operations makes necessary the planning and programing of the measuring, monitoring and quality control into the technological process during manufacturing operation. In this way, taking into consideration the technological possibilities of lathe canters, the scope of computer aided technological planning duties significantly increases. It is trivial requirement to give only once the descriptions of the prefabricated parts and ready made parts. Starting taking into account these careful considerations we have been developing the planning system of technology of body of revolution on the base of GTIPROG/EC system which useful for programming of lathe centers. Out paper deals with the results of development and the occurring problems.

A follow-up meeting post death is appreciated by family members of deceased patients.

PubMed

Kock, M; Berntsson, C; Bengtsson, A

2014-08-01

A practice with a follow-up meeting post death (FUMPD) with physician and staff for family members of patients who died in the intensive care unit (ICU) was started as a quality project to improve the support of families in post-ICU bereavement. A quality improvement control was conducted after 4 years. The quality improvement control was made retrospectively as an anonymous non-coded questionnaire. Part A related to the FUMPD. Part B inquired if we could contact the family member again for a research project to evaluate family support post-ICU bereavement. The questionnaires were sent to 84 family members of 56 deceased patients. Part A: 46 out of 84 family members answered and had attended a FUMPD. Ninety-one percent of the family members thought that we should continue to offer FUMPD. Seventy-eight percent were satisfied with their meeting. Eighty percent felt that they understood the cause of death. The majority wanted the meeting to take place within 6 weeks of death. Ninety-one percent rated the physician as important to be present at the meeting. The social worker was rated more important to attend the meeting than the assistant nurse. Ninety-one percent wanted to discuss the cause of death.Part B: 54 out of 84 family members answered. Twenty out of 54 did not want us to contact them again. A routine with a Follow-Up Meeting Post Death with the ICU team for the families of the patients who die in the ICU is appreciated. The presence of the physician is important. © 2014 The Acta Anaesthesiologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Design verification and fabrication of active control systems for the DAST ARW-2 high aspect ratio wing. Part 2: Appendices

NASA Technical Reports Server (NTRS)

Mcgehee, C. R.

1986-01-01

This is Part 2-Appendices of a study conducted under Drones for Aerodynamic and Structural Testing (DAST) Program to accomplish the final design and hardware fabrication for four active control systems compatible with and ready for installation in the NASA Aeroelastic Research Wing No. 2 (ARW-2) and Firebee II drone flight test vehicle. The wing structure was designed so that Active Control Systems (ACS) are required in the normal flight envelope by integrating control system design with aerodynamics and structure technologies. The DAST ARW-2 configuration uses flutter suppression, relaxed static stability, and gust and maneuver load alleviation ACS systems, and an automatic flight control system. Performance goals and criteria were applied to individual systems and the systems collectively to assure that vehicle stability margins, flutter margins, flying qualities, and load reductions were achieved.

Water resources data, Indiana, water year 1982

USGS Publications Warehouse

Miller, R.L.; Hoggatt, R.E.; Nell, G.E.

1983-01-01

Water resources data for the 1982 water year for Indiana consists of records of stage, discharge, and water quality of streams; stage and contents of lakes and reservoirs; and water levels in wells. This report contains discharge records for 176 gaging stations, stage and contents for 9 lakes and reservoirs, releases from 8 flood control reservoirs, water quality for 26 gaging stations, and water levels for 87 observation wells. Also included are 71 crest-stage partial-record stations. Additional water data were collected at various sites, not part of the systematic data-collection program, and are published as miscellaneous measurements. These data represent that part of the National Water Data System operated by the U.S. Geological Survey and cooperating State and Federal agencies in Indiana.

Water resources data, Indiana, water year 1983

USGS Publications Warehouse

Miller, R.L.; Hoggatt, R.E.; Nell, G.E.

1984-01-01

Water resources data for the 1983 water year for Indiana consists of records of stage, discharge, and water quality of streams; stage and contents of lakes and reservoirs; and water levels in wells. This report contains discharge records for 174 gaging stations, stage and contents for 9 lake and reservoirs, releases from 7 flood control reservoirs, water quality for 5 gaging stations, and water levels for 84 observation wells. Also included are 23 crest-stage partial-record stations. Additional water data were collected at various sites, not part of the systematic data-collection program, and are published as miscellaneous measurements. These data represent that part of the National Water Data System operated by the U.S. Geological Survey and cooperating State and Federal agencies in Indiana.

The new production theory for health care through clinical reengineering: a study of clinical guidelines--Part I.

PubMed

Sharp, J R

1994-12-01

Drucker writes that the emerging theory of manufacturing includes four principles and practices: statistical quality control, manufacturing accounting, modular organization, and systems approach. SQC is a rigorous, scientific method of identifying variation in the quality and productivity of a given production process, with an emphasis on improvement. The new manufacturing economics intends to integrate the production strategy with the business strategy in order to account for the biggest portions of costs that the old methods did not assess: time and automation. Production operations that are both standardized and flexible will allow the organization to keep up with changes in design, technology, and the market. The return on innovation in this environment is predicated on a modular arrangement of flexible steps in the process. Finally, the systems approach sees the entire process as being integrated in converting goods or services into economic satisfaction. There is now a major restructuring of the U.S. health care industry, and the incorporation of these four theories into health care reform would appear to be essential. This two-part article will address two problems: Will Drucker's theories relate to health care (Part I)? Will the "new manufacturing" in health care (practice guidelines) demonstrate cost, quality, and access changes that reform demands (Part II)?

Control of Next Generation Aircraft and Wind Turbines

NASA Technical Reports Server (NTRS)

Frost, Susan

2010-01-01

The first part of this talk will describe some of the exciting new next generation aircraft that NASA is proposing for the future. These aircraft are being designed to reduce aircraft fuel consumption and environmental impact. Reducing the aircraft weight is one approach that will be used to achieve these goals. A new control framework will be presented that enables lighter, more flexible aircraft to maintain aircraft handling qualities, while preventing the aircraft from exceeding structural load limits. The second part of the talk will give an overview of utility-scale wind turbines and their control. Results of collaboration with Dr. Balas will be presented, including new theory to adaptively control the turbine in the presence of structural modes, with the focus on the application of this theory to a high-fidelity simulation of a wind turbine.

Corner smoothing of 2D milling toolpath using b-spline curve by optimizing the contour error and the feedrate

NASA Astrophysics Data System (ADS)

Özcan, Abdullah; Rivière-Lorphèvre, Edouard; Ducobu, François

2018-05-01

In part manufacturing, efficient process should minimize the cycle time needed to reach the prescribed quality on the part. In order to optimize it, the machining time needs to be as low as possible and the quality needs to meet some requirements. For a 2D milling toolpath defined by sharp corners, the programmed feedrate is different from the reachable feedrate due to kinematic limits of the motor drives. This phenomena leads to a loss of productivity. Smoothing the toolpath allows to reduce significantly the machining time but the dimensional accuracy should not be neglected. Therefore, a way to address the problem of optimizing a toolpath in part manufacturing is to take into account the manufacturing time and the part quality. On one hand, maximizing the feedrate will minimize the manufacturing time and, on the other hand, the maximum of the contour error needs to be set under a threshold to meet the quality requirements. This paper presents a method to optimize sharp corner smoothing using b-spline curves by adjusting the control points defining the curve. The objective function used in the optimization process is based on the contour error and the difference between the programmed feedrate and an estimation of the reachable feedrate. The estimation of the reachable feedrate is based on geometrical information. Some simulation results are presented in the paper and the machining times are compared in each cases.

Formaldehyde Concentration Dynamics of the International Space Station Cabin Atmosphere

NASA Technical Reports Server (NTRS)

Perry, J. L.

2005-01-01

Formaldehyde presents a significant challenge to maintaining cabin air quality on board crewed spacecraft. Generation sources include offgassing from a variety of non-metallic materials as well as human metabolism. Because generation sources are pervasive and human health can be affected by continual exposure to low concentrations, toxicology and air quality control engineering experts jointly identified formaldehyde as a key compound to be monitored as part the International Space Station's (ISS) environmental health monitoring and maintenance program. Data acquired from in-flight air quality monitoring methods are the basis for assessing the cabin environment's suitability for long-term habitation and monitoring the performance of passive and active controls that are in place to minimize crew exposure. Formaldehyde concentration trends and dynamics served in the ISS cabin atmosphere are reviewed implications to present and future flight operations discussed.

Alining Large Cylinders for Welding

NASA Technical Reports Server (NTRS)

Ehl, J. H.

1985-01-01

Special tooling alines and holds internally-stiffened large-diameter cylindrical parts for welding. Alinement brackets attached to strengthening fins on insides of cylindrical tank sections. Jackscrews on brackets raised or lowered to eliminate mismatches between adjacent sections. Tooling substantially reduces costs while allowing more precise control and improved quality.

40 CFR 52.254 - Organic solvent usage.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Air Quality Control Regions (the “Regions”), as described in 40 CFR part 81, dated July 1, 1979... contrivances designed for processing continuous web, strip, or wire that emit organic materials in the course... articles, machines, equipment, or other contrivances designed for processing a continuous web, strip, or...

40 CFR 52.254 - Organic solvent usage.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Air Quality Control Regions (the “Regions”), as described in 40 CFR part 81, dated July 1, 1979... contrivances designed for processing continuous web, strip, or wire that emit organic materials in the course... articles, machines, equipment, or other contrivances designed for processing a continuous web, strip, or...

40 CFR 52.254 - Organic solvent usage.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Air Quality Control Regions (the “Regions”), as described in 40 CFR part 81, dated July 1, 1979... contrivances designed for processing continuous web, strip, or wire that emit organic materials in the course... articles, machines, equipment, or other contrivances designed for processing a continuous web, strip, or...

40 CFR 52.254 - Organic solvent usage.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Air Quality Control Regions (the “Regions”), as described in 40 CFR part 81, dated July 1, 1979... contrivances designed for processing continuous web, strip, or wire that emit organic materials in the course... articles, machines, equipment, or other contrivances designed for processing a continuous web, strip, or...

7 CFR 275.2 - State agency responsibilities.

Code of Federal Regulations, 2014 CFR

2014-01-01

...: (i) Data collection through management evaluation (ME) reviews and quality control (QC) reviews; (ii... knowledge of either the household or the decision under review. Where there is prior knowledge, the reviewer must disqualify her/himself. Prior knowledge is defined as having: (1) Taken any part in the decision...

7 CFR 275.2 - State agency responsibilities.

Code of Federal Regulations, 2011 CFR

2011-01-01

...: (i) Data collection through management evaluation (ME) reviews and quality control (QC) reviews; (ii... knowledge of either the household or the decision under review. Where there is prior knowledge, the reviewer must disqualify her/himself. Prior knowledge is defined as having: (1) Taken any part in the decision...

7 CFR 275.2 - State agency responsibilities.

Code of Federal Regulations, 2013 CFR

2013-01-01

...: (i) Data collection through management evaluation (ME) reviews and quality control (QC) reviews; (ii... knowledge of either the household or the decision under review. Where there is prior knowledge, the reviewer must disqualify her/himself. Prior knowledge is defined as having: (1) Taken any part in the decision...

7 CFR 275.2 - State agency responsibilities.

Code of Federal Regulations, 2012 CFR

2012-01-01

...: (i) Data collection through management evaluation (ME) reviews and quality control (QC) reviews; (ii... knowledge of either the household or the decision under review. Where there is prior knowledge, the reviewer must disqualify her/himself. Prior knowledge is defined as having: (1) Taken any part in the decision...

44 CFR Appendix B to Part 62 - National Flood Insurance Program

Code of Federal Regulations, 2014 CFR

2014-10-01

... quality control departments, or both, and independent Certified Public Accountant (CPA) firms. This Plan... individual State Insurance Departments, NAIC Zone examinations, and independent CPA firms. (c) Standards... company must— (A) Have a biennial audit of the flood insurance financial statements conducted by a CPA...

44 CFR Appendix B to Part 62 - National Flood Insurance Program

Code of Federal Regulations, 2013 CFR

2013-10-01

... quality control departments, or both, and independent Certified Public Accountant (CPA) firms. This Plan... individual State Insurance Departments, NAIC Zone examinations, and independent CPA firms. (c) Standards... company must— (A) Have a biennial audit of the flood insurance financial statements conducted by a CPA...

7 CFR 275.2 - State agency responsibilities.

Code of Federal Regulations, 2010 CFR

2010-01-01

...: (i) Data collection through management evaluation (ME) reviews and quality control (QC) reviews; (ii... knowledge of either the household or the decision under review. Where there is prior knowledge, the reviewer must disqualify her/himself. Prior knowledge is defined as having: (1) Taken any part in the decision...

40 CFR Appendix A to Part 81 - Air Quality Control Regions (AQCR's)

Code of Federal Regulations, 2011 CFR

2011-07-01

... Arkansas 20 Northwest Arkansas 21 Shreveport-Texarkana-Tyler (La., Okla., Texas) 22 California: Great Basin... Louisiana: Monroe-El Dorado (Ark.) 19 Shreveport-Texarkana-Tyler (Ark., Okla., Tex.) 22 Southern Louisiana... 186 Northwestern Oklahoma 187 Shreveport-Texarkana-Tyler (Ark., La., Texas) 22 Southeastern Oklahoma...

40 CFR Appendix A to Part 81 - Air Quality Control Regions (AQCR's)

Code of Federal Regulations, 2014 CFR

2014-07-01

... Arkansas 20 Northwest Arkansas 21 Shreveport-Texarkana-Tyler (La., Okla., Texas) 22 California: Great Basin... Louisiana: Monroe-El Dorado (Ark.) 19 Shreveport-Texarkana-Tyler (Ark., Okla., Tex.) 22 Southern Louisiana... 186 Northwestern Oklahoma 187 Shreveport-Texarkana-Tyler (Ark., La., Texas) 22 Southeastern Oklahoma...

40 CFR Appendix A to Part 81 - Air Quality Control Regions (AQCR's)

Code of Federal Regulations, 2012 CFR

2012-07-01

... Arkansas 20 Northwest Arkansas 21 Shreveport-Texarkana-Tyler (La., Okla., Texas) 22 California: Great Basin... Louisiana: Monroe-El Dorado (Ark.) 19 Shreveport-Texarkana-Tyler (Ark., Okla., Tex.) 22 Southern Louisiana... 186 Northwestern Oklahoma 187 Shreveport-Texarkana-Tyler (Ark., La., Texas) 22 Southeastern Oklahoma...

40 CFR Appendix A to Part 81 - Air Quality Control Regions (AQCR's)

Code of Federal Regulations, 2013 CFR

2013-07-01

... Arkansas 20 Northwest Arkansas 21 Shreveport-Texarkana-Tyler (La., Okla., Texas) 22 California: Great Basin... Louisiana: Monroe-El Dorado (Ark.) 19 Shreveport-Texarkana-Tyler (Ark., Okla., Tex.) 22 Southern Louisiana... 186 Northwestern Oklahoma 187 Shreveport-Texarkana-Tyler (Ark., La., Texas) 22 Southeastern Oklahoma...

40 CFR Appendix A to Part 81 - Air Quality Control Regions (AQCR's)

Code of Federal Regulations, 2010 CFR

2010-07-01

... Arkansas 20 Northwest Arkansas 21 Shreveport-Texarkana-Tyler (La., Okla., Texas) 22 California: Great Basin... Louisiana: Monroe-El Dorado (Ark.) 19 Shreveport-Texarkana-Tyler (Ark., Okla., Tex.) 22 Southern Louisiana... 186 Northwestern Oklahoma 187 Shreveport-Texarkana-Tyler (Ark., La., Texas) 22 Southeastern Oklahoma...

40 CFR 406.24 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... process wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works...

40 CFR 406.14 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... process wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works...

40 CFR 446.16 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... process wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works...

40 CFR 446.16 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... process wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works...

A 10 cm Dual Frequency Doppler Weather Radar. Part I. The Radar System.

DTIC Science & Technology

1982-10-25

Evaluation System ( RAMCES )". The step attenuator required for this calibration can be programmed remotely, has low power and temperature coefficients, and...Control and Evaluation System". The Quality Assurance/Fault Location Network makes use of fault location techniques at critical locations in the radar and...quasi-con- tinuous monitoring of radar performance. The Radar Monitor, Control and Evaluation System provides for automated system calibration and

[Research advances in secondary development of Chinese patent medicines based on quality by design concept].

PubMed

Gong, Xing-Chu; Chen, Teng; Qu, Hai-Bin

2017-03-01

Quality by design (QbD) concept is an advanced pharmaceutical quality control concept. The application of QbD concept in the research and development of pharmaceutical processes of traditional Chinese medicines (TCM) mainly contains five parts, including the definition of critical processes and their evaluation criteria, the determination of critical process parameters and critical material attributes, the establishment of quantitative models, the development of design space, as well as the application and continuous improvement of control strategy. In this work, recent research advances in QbD concept implementation methods in the secondary development of Chinese patent medicines were reviewed, and five promising fields of the implementation of QbD concept were pointed out, including the research and development of TCM new drugs and Chinese medicine granules for formulation, modeling of pharmaceutical processes, development of control strategy based on industrial big data, strengthening the research of process amplification rules, and the development of new pharmaceutical equipment.. Copyright© by the Chinese Pharmaceutical Association.

Quality control for the first large areas of triple-GEM chambers for the CMS endcaps

NASA Astrophysics Data System (ADS)

Abbaneo, D.; Abbas, M.; Abbrescia, M.; Abi Akl, M.; Aboamer, O.; Acosta, D.; Ahmad, A.; Ahmed, W.; Aleksandrov, A.; Altieri, P.; Asawatangtrakuldee, C.; Aspell, P.; Assran, Y.; Awan, I.; Bally, S.; Ban, Y.; Banerjee, S.; Barashko, V.; Barria, P.; Bencze, G.; Beni, N.; Benussi, L.; Bhopatkar, V.; Bianco, S.; Bos, J.; Bouhali, O.; Braghieri, A.; Braibant, S.; Buontempo, S.; Calabria, C.; Caponero, M.; Caputo, C.; Cassese, F.; Castaneda, A.; Cauwenbergh, S.; Cavallo, F. R.; Celik, A.; Choi, M.; Choi, S.; Christiansen, J.; Cimmino, A.; Colafranceschi, S.; Colaleo, A.; Conde Garcia, A.; Czellar, S.; Dabrowski, M. M.; De Lentdecker, G.; De Oliveira, R.; de Robertis, G.; Dildick, S.; Dorney, B.; Endroczi, G.; Errico, F.; Fenyvesi, A.; Ferry, S.; Furic, I.; Giacomelli, P.; Gilmore, J.; Golovtsov, V.; Guiducci, L.; Guilloux, F.; Gutierrez, A.; Hadjiiska, R. M.; Hauser, J.; Hoepfner, K.; Hohlmann, M.; Hoorani, H.; Iaydjiev, P.; Jeng, Y. G.; Kamon, T.; Karchin, P.; Korytov, A.; Krutelyov, S.; Kumar, A.; Kim, H.; Lee, J.; Lenzi, T.; Litov, L.; Loddo, F.; Madorsky, A.; Maerschalk, T.; Maggi, M.; Magnani, A.; Mal, P. K.; Mandal, K.; Marchioro, A.; Marinov, A.; Majumdar, N.; Merlin, J. A.; Mitselmakher, G.; Mohanty, A. K.; Mohapatra, A.; Molnar, J.; Muhammad, S.; Mukhopadhyay, S.; Naimuddin, M.; Nuzzo, S.; Oliveri, E.; Pant, L. M.; Paolucci, P.; Park, I.; Passeggio, G.; Pavlov, B.; Philipps, B.; Piccolo, D.; Postema, H.; Puig Baranac, A.; Radi, A.; Radogna, R.; Raffone, G.; Ranieri, A.; Rashevski, G.; Riccardi, C.; Rodozov, M.; Rodrigues, A.; Ropelewski, L.; RoyChowdhury, S.; Ryu, G.; Ryu, M. S.; Safonov, A.; Salva, S.; Saviano, G.; Sharma, A.; Sharma, A.; Sharma, R.; Shah, A. H.; Shopova, M.; Sturdy, J.; Sultanov, G.; Swain, S. K.; Szillasi, Z.; Talvitie, J.; Tatarinov, A.; Tuuva, T.; Tytgat, M.; Vai, I.; Van Stenis, M.; Venditti, R.; Verhagen, E.; Verwilligen, P.; Vitulo, P.; Volkov, S.; Vorobyev, A.; Wang, D.; Wang, M.; Yang, U.; Yang, Y.; Yonamine, R.; Zaganidis, N.; Zenoni, F.; Zhang, A.

2018-02-01

The CMS Collaboration plans to equip the very forward muon system with triple-GEM detectors that can withstand the environment of the High-Luminosity LHC. This project is at the final stages of R&D and moving to production. An unprecedented large area of several 100 m2 are to be instrumented with GEM detectors which will be produced in six different sites around the world. A common construction and quality control procedure is required to ensure the performance of each detector. The quality control steps will include optical inspection, cleaning and baking of all materials and parts used to build the detector, leakage current tests of the GEM foils, high voltage tests, gas leak tests of the chambers and monitoring pressure drop vs. time, gain calibration to know the optimal operation region of the detector, gain uniformity tests, and studying the efficiency, noise and tracking performance of the detectors in a cosmic stand using scintillators.

Feasibility of UV-VIS-Fluorescence spectroscopy combined with pattern recognition techniques to authenticate a new category of plant food supplements.

PubMed

Boggia, Raffaella; Turrini, Federica; Anselmo, Marco; Zunin, Paola; Donno, Dario; Beccaro, Gabriele L

2017-07-01

Bud extracts, named also "gemmoderivatives", are a new category of natural products, obtained macerating meristematic fresh tissues of trees and plants. In the European Community these botanical remedies are classified as plant food supplements. Nowadays these products are still poorly studied, even if they are widely used and commercialized. Several analytical tools for the quality control of these very expensive supplements are urgently needed in order to avoid mislabelling and frauds. In fact, besides the usual quality controls common to the other botanical dietary supplements, these extracts should be checked in order to quickly detect if the cheaper adult parts of the plants are deceptively used in place of the corresponding buds whose harvest-period and production are extremely limited. This study aims to provide a screening analytical method based on UV-VIS-Fluorescence spectroscopy coupled to multivariate analysis for a rapid, inexpensive and non-destructive quality control of these products.

Effect of weight reduction on the quality of life in obese patients with fibromyalgia syndrome: a randomized controlled trial.

PubMed

Senna, Mohammed Kamal; Sallam, Rehab Abd-El Raouf; Ashour, Hala Salah; Elarman, Mohammed

2012-11-01

The aim of the study was to examine whether weight reduction can result in improvement of fibromyalgia impact questionnaire (FIQ) in the patients with fibromyalgia syndrome (FMS). This study was a randomized controlled trial. Obese patients with fibromyalgia were randomly assigned to 6-month dietary weight loss (n = 41) and no weight loss (n = 42) groups. Patients were assessed at baseline and at 6 months. The primary outcome measure was FIQ. Secondary measures included the tender point (TP) examination, Beck Depression Inventory-II, and Pittsburg Sleep Quality Index. Compared to the control group, patients who underwent weight reduction obtained significantly better FIQ (p = 0.007), lower mean TP count (p = 0.015), and lower mean TP pain rating in the lower body (p < 0.001). Patients who lost weight had less depression and better sleep quality than the controls. Patients who lost weight had significantly lower interleukin 6 and C-reactive protein levels than those in the control group (p = 0.034 and p = 0.007, respectively). Weight loss in obese patients with FMS leads to significant improvement in the quality of life as shown by the decrease in the FIQ score. Depression, sleep quality, and tender point count are also significantly improved by weight loss in obese patients with fibromyalgia. Our results suggest that weight reduction should be a part of fibromyalgia treatment.

Guidelines for the processing and quality assurance of benthic invertebrate samples collected as part of the National Water-Quality Assessment Program

USGS Publications Warehouse

Cuffney, T.F.; Gurtz, M.E.; Meador, M.R.

1993-01-01

Benthic invertebrate samples are collected as part of the U.S. Geological Survey's National Water-Quality Assessment Program. This is a perennial, multidisciplinary program that integrates biological, physical, and chemical indicators of water quality to evaluate status and trends and to develop an understanding of the factors controlling observed water quality. The Program examines water quality in 60 study units (coupled ground- and surface-water systems) that encompass most of the conterminous United States and parts of Alaska and Hawaii. Study-unit teams collect and process qualitative and semi-quantitative invertebrate samples according to standardized procedures. These samples are processed (elutriated and subsampled) in the field to produce as many as four sample components: large-rare, main-body, elutriate, and split. Each sample component is preserved in 10-percent formalin, and two components, large-rare and main-body, are sent to contract laboratories for further processing. The large-rare component is composed of large invertebrates that are removed from the sample matrix during field processing and placed in one or more containers. The main-body sample component consists of the remaining sample materials (sediment, detritus, and invertebrates) and is subsampled in the field to achieve a volume of 750 milliliters or less. The remaining two sample components, elutriate and split, are used for quality-assurance and quality-control purposes. Contract laboratories are used to identify and quantify invertebrates from the large-rare and main-body sample components according to the procedures and guidelines specified within this document. These guidelines allow the use of subsampling techniques to reduce the volume of sample material processed and to facilitate identifications. These processing procedures and techniques may be modified if the modifications provide equal or greater levels of accuracy and precision. The intent of sample processing is to determine the quantity of each taxon present in the semi-quantitative samples or to list the taxa present in qualitative samples. The processing guidelines provide standardized laboratory forms, sample labels, detailed sample processing flow charts, standardized format for electronic data, quality-assurance procedures and checks, sample tracking standards, and target levels for taxonomic determinations. The contract laboratory (1) is responsible for identifications and quantifications, (2) constructs reference collections, (3) provides data in hard copy and electronic forms, (4) follows specified quality-assurance and quality-control procedures, and (5) returns all processed and unprocessed portions of the samples. The U.S. Geological Survey's Quality Management Group maintains a Biological Quality-Assurance Unit, located at the National Water-Quality Laboratory, Arvada, Colorado, to oversee the use of contract laboratories and ensure the quality of data obtained from these laboratories according to the guidelines established in this document. This unit establishes contract specifications, reviews contractor performance (timeliness, accuracy, and consistency), enters data into the National Water Information System-II data base, maintains in-house reference collections, deposits voucher specimens in outside museums, and interacts with taxonomic experts within and outside the U.S. Geological Survey. This unit also modifies the existing sample processing and quality-assurance guidelines, establishes criteria and testing procedures for qualifying potential contract laboratories, identifies qualified taxonomic experts, and establishes voucher collections.

Some aspects of precise laser machining - Part 1: Theory

NASA Astrophysics Data System (ADS)

Wyszynski, Dominik; Grabowski, Marcin; Lipiec, Piotr

2018-05-01

The paper describes the role of laser beam polarization and deflection on quality of laser beam machined parts made of difficult to cut materials (used for cutting tools). Application of efficient and precise cutting tool (laser beam) has significant impact on preparation and finishing operations of cutting tools for aviation part manufacturing. Understanding the phenomena occurring in the polarized light laser cutting gave possibility to design, build and test opto-mechanical instrumentation to control and maintain process parameters and conditions. The research was carried within INNOLOT program funded by Polish National Centre for Research and Development.

Development and demonstration of manufacturing processes for fabricating graphite/LARC-160 polyimide structural elements, part 4, paragraph B

NASA Technical Reports Server (NTRS)

1980-01-01

A quality assurance program was developed which included specifications for celion/LARC-160 polyimide materials and quality control of materials and processes. The effects of monomers and/or polymer variables and prepeg variables on the processibility of celion/LARC prepeg were included. Processes for fabricating laminates, honeycomb core panels, and chopped fiber moldings were developed. Specimens and conduct tests were fabricated to qualify the processes for fabrication of demonstration components.

Historical overview of V/STOL aircraft technology

NASA Technical Reports Server (NTRS)

Anderson, S. B.

1981-01-01

The requirements for satisfactory characteristics in several key technology areas are discussed and a review is made of various V/STOL aircraft for the purpose of assessing the success or failure of each design in meeting design requirements. Special operating techniques were developed to help circumvent deficiencies. For the most part performance and handling qualities limitations restricted operational evaluations. Flight operations emphasized the need for good STOL performance, good handling qualities, and stability and control augmentation. The majority of aircraft suffered adverse ground effects.

Mitochondrial quality control and communications with the nucleus are important in maintaining mitochondrial function and cell health☆☆☆

PubMed Central

Kotiadis, Vassilios N.; Duchen, Michael R.; Osellame, Laura D.

2014-01-01

Background The maintenance of cell metabolism and homeostasis is a fundamental characteristic of living organisms. In eukaryotes, mitochondria are the cornerstone of these life supporting processes, playing leading roles in a host of core cellular functions, including energy transduction, metabolic and calcium signalling, and supporting roles in a number of biosynthetic pathways. The possession of a discrete mitochondrial genome dictates that the maintenance of mitochondrial ‘fitness’ requires quality control mechanisms which involve close communication with the nucleus. Scope of review This review explores the synergistic mechanisms that control mitochondrial quality and function and ensure cellular bioenergetic homeostasis. These include antioxidant defence mechanisms that protect against oxidative damage caused by reactive oxygen species, while regulating signals transduced through such free radicals. Protein homeostasis controls import, folding, and degradation of proteins underpinned by mechanisms that regulate bioenergetic capacity through the mitochondrial unfolded protein response. Autophagic machinery is recruited for mitochondrial turnover through the process of mitophagy. Mitochondria also communicate with the nucleus to exact specific transcriptional responses through retrograde signalling pathways. Major conclusions The outcome of mitochondrial quality control is not only reliant on the efficient operation of the core homeostatic mechanisms but also in the effective interaction of mitochondria with other cellular components, namely the nucleus. General significance Understanding mitochondrial quality control and the interactions between the organelle and the nucleus will be crucial in developing therapies for the plethora of diseases in which the pathophysiology is determined by mitochondrial dysfunction. This article is part of a Special Issue entitled Frontiers of Mitochondrial Research. PMID:24211250

Construction of quality-assured infant feeding process of care data repositories: definition and design (Part 1).

PubMed

Garcí A-de-León-Chocano, Ricardo; Sáez, Carlos; Muñoz-Soler, Verónica; Garcí A-de-León-González, Ricardo; García-Gómez, Juan M

2015-12-01

This is the first paper of a series of two regarding the construction of data quality (DQ) assured repositories for the reuse of information on infant feeding from birth until two years old. This first paper justifies the need for such repositories and describes the design of a process to construct them from Electronic Health Records (EHR). As a result, Part 1 proposes a computational process to obtain quality-assured datasets represented by a canonical structure extracted from raw data from multiple EHR. For this, 13 steps were defined to ensure the harmonization, standardization, completion, de-duplication, and consistency of the dataset content. Moreover, the quality of the input and output data for each of these steps is controlled according to eight DQ dimensions: predictive value, correctness, duplication, consistency, completeness, contextualization, temporal-stability and spatial-stability. The second paper of the series will describe the application of this computational process to construct the first quality-assured repository for the reuse of information on infant feeding in the perinatal period aimed at the monitoring of clinical activities and research. Copyright © 2015 Elsevier Ltd. All rights reserved.

Introduction of Transplant Registry Unified Management Program 2 (TRUMP2): scripts for TRUMP data analyses, part I (variables other than HLA-related data).

PubMed

Atsuta, Yoshiko

2016-01-01

Collection and analysis of information on diseases and post-transplant courses of allogeneic hematopoietic stem cell transplant recipients have played important roles in improving therapeutic outcomes in hematopoietic stem cell transplantation. Efficient, high-quality data collection systems are essential. The introduction of the Second-Generation Transplant Registry Unified Management Program (TRUMP2) is intended to improve data quality and more efficient data management. The TRUMP2 system will also expand possible uses of data, as it is capable of building a more complex relational database. The construction of an accessible data utilization system for adequate data utilization by researchers would promote greater research activity. Study approval and management processes and authorship guidelines also need to be organized within this context. Quality control of processes for data manipulation and analysis will also affect study outcomes. Shared scripts have been introduced to define variables according to standard definitions for quality control and improving efficiency of registry studies using TRUMP data.

Patti Labbe | Frederick National Laboratory for Cancer Research

Cancer.gov

Looking back, Patti Labbe realizes that she’s always felt at home working in quality control. She got her start in the field soon after graduating college, and it’s been a part of her life ever since. “QC work was a great fit for me,” she sa

76 FR 1167 - Statement of Organization, Functions, and Delegations of Authority

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-07

... Organization, Functions, and Delegations of Authority Part C (Centers for Disease Control and Prevention) of the Statement of Organization, Functions, and Delegations of Authority of the Department of Health and... Functions, is hereby amended as follows: Delete in its entirety the title for the Office of Science Quality...

40 CFR 96.72 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality assurance requirements of appendix B of part 75 of this chapter, data shall be substituted using...) Audit decertification. Whenever both an audit of a monitoring system and a review of the initial... certification or recertification application submission and at the time of the audit, the permitting authority...

Control of sprouting of tanoak and madone stumps

Treesearch

G. H. Schubert

1950-01-01

In part of the high- site-quality pine and fir types of California, stand improvement cuttings are made especially difficult by the sprouting habit of tanoak (Lithocarpus densiflora Hook . and Arn . ) and madrone (Arbutus menziesii Pursh.). The stumps of these species sprout so vigorously that release of the favored crop trees...

78 FR 65877 - Approval and Promulgation of Implementation Plans; Atlanta, Georgia 1997 8-Hour Ozone...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-04

... Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Incorporation by reference...-hour ozone national ambient air quality standards (NAAQS) nonattainment area (hereafter referred to as... Section, Air Planning Branch, Air, Pesticides and Toxics Management Division, U.S. Environmental...

The Sociology of Urban Education: Desegregation and Integration.

ERIC Educational Resources Information Center

Willie, Charles Vert

In this book, the problems of racial segregation and desegregation in urban schools and colleges are discussed in light of cultural, biological, and social questions. Part I explores various issues in urban education, such as racial balance and quality education, white flight, community control, the city-suburban connection, education for the…

Odor and odorous chemical emissions from animal buildings: part 1 - project overview, collection methods, and quality control

USDA-ARS?s Scientific Manuscript database

Livestock facilities have historically generated public concerns due to their emissions of odorous air and various chemical pollutants. Odor emission factors and identification of principal odorous chemicals are needed to better understand the problem. Applications of odor emission factors include i...

78 FR 78726 - Approval and Promulgation of Air Quality Implementation Plans; Indiana; Volatile Organic Compound...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R05-OAR-2012-0453; FRL-9904-35-Region 5... Control Measures for Industrial Solvent Cleaning for Northwest Indiana AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: The Environmental Protection Agency (EPA) is approving a...

77 FR 43000 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Offset Lithographic...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-23

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R03-OAR-2012-0042; FRL-9702-2] Approval and... Printing Regulations AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: EPA is... Technology (RACT) for sources covered by EPA's Control Techniques Guidelines (CTG) for offset lithographic...

40 CFR 85.2120 - Maintenance and submittal of records.

Code of Federal Regulations, 2011 CFR

2011-07-01

... establish, maintain and retain for 5 years the following adequately organized and indexed records: (1...) All data obtained during testing of the part and subsequent analyses based on that data, including the... applicable certification requirements; (6) All data taken in implementing the quality control plan, and any...

40 CFR 85.2120 - Maintenance and submittal of records.

Code of Federal Regulations, 2012 CFR

2012-07-01

... establish, maintain and retain for 5 years the following adequately organized and indexed records: (1...) All data obtained during testing of the part and subsequent analyses based on that data, including the... applicable certification requirements; (6) All data taken in implementing the quality control plan, and any...

40 CFR 85.2120 - Maintenance and submittal of records.

Code of Federal Regulations, 2013 CFR

2013-07-01

... establish, maintain and retain for 5 years the following adequately organized and indexed records: (1...) All data obtained during testing of the part and subsequent analyses based on that data, including the... applicable certification requirements; (6) All data taken in implementing the quality control plan, and any...

40 CFR 85.2120 - Maintenance and submittal of records.

Code of Federal Regulations, 2014 CFR

2014-07-01

... establish, maintain and retain for 5 years the following adequately organized and indexed records: (1...) All data obtained during testing of the part and subsequent analyses based on that data, including the... applicable certification requirements; (6) All data taken in implementing the quality control plan, and any...

QUALITY CONTROL OF SEMI-CONTINUOUS MOBILITY SIZE-FRACTIONATED PARTICLE NUMBER CONCENTRATION DATA. (R827352)

EPA Science Inventory

Fine and ultrafine particles have been postulated to play an important role in the association between ambient particulate matters and adverse health effects. As part of the EPA Supersite Program, the Southern California Particle Center & Supersite has conducted a series o...

40 CFR 123.63 - Criteria for withdrawal of State programs.

Code of Federal Regulations, 2014 CFR

2014-07-01

... programs. 123.63 Section 123.63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... requirements of this part, including: (i) Failure to exercise control over activities required to be regulated... regulatory program for developing water quality-based effluent limits in NPDES permits. (6) Where a Great...

40 CFR 123.63 - Criteria for withdrawal of State programs.

Code of Federal Regulations, 2012 CFR

2012-07-01

... programs. 123.63 Section 123.63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... requirements of this part, including: (i) Failure to exercise control over activities required to be regulated... regulatory program for developing water quality-based effluent limits in NPDES permits. (6) Where a Great...

Occupational Preparation--Inspection and Quality Control. Instructor's Guide. The Manufacturing Cluster.

ERIC Educational Resources Information Center

Fairleigh Dickinson Univ., Rutherford, NJ.

Part of a manufacturing cluster series which addresses itself to career awareness, orientation, exploration, and preparation, this guide and its accompanying student manual were written as a direct followup of the instructor's guide and student manual titled "Exploring Manufacturing Occupations." Four major sections are included. The first section…

CONTROLLED, SHORT-TERM DERMAL AND INHALATION EXPOSURE TO MTBE AND DIBROMOCHLOROMETHANE

EPA Science Inventory

The oxygenate methyl tert-butyl ether (MTBE) has been added to gasoline to meet national ambient air quality standards in those parts of the US that are non-compliant for carbon monoxide. Although MTBE has provided important health benefits in terms of reduced hazardous air po...

40 CFR 407.44 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 407.34 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 408.114 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the...

40 CFR 406.96 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged to a publicly owned treatment works by a new...

40 CFR 427.106 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged to a publicly owned treatment works by a new...

40 CFR 408.134 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the...

40 CFR 405.54 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this subpart...

40 CFR 407.14 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this subpart...

40 CFR 408.24 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 447.16 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a new...

40 CFR 408.34 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 407.84 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by any existing point source subject...

40 CFR 406.86 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged to a publicly owned treatment works by a new point source subject...

40 CFR 408.194 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 408.94 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 408.164 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 407.54 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 408.84 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to...

40 CFR 427.106 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged to a publicly owned treatment works by a new...

40 CFR 407.86 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a new point source subject to the provisions of...

40 CFR 405.54 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this subpart...

40 CFR 408.186 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a new source subject to the provisions of this subpart...

40 CFR 408.104 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 408.184 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 407.66 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a new point source subject to the provisions of this...

40 CFR 427.96 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged to a publicly owned treatment works by a new...

40 CFR 408.44 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 408.64 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the...

40 CFR 427.96 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged to a publicly owned treatment works by a new...

40 CFR 408.74 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the...

40 CFR 407.64 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by any existing point source subject to the...

40 CFR 407.24 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 407.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a new point source subject to the provisions of this...

40 CFR 408.54 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 447.16 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... wastewater pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a new...

40 CFR 407.74 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by any existing point source subject...

40 CFR 406.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged to a publicly owned treatment works by a new point source subject...

40 CFR 408.174 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this...

40 CFR 408.14 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to the provisions of this subpart...

40 CFR 408.124 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pollutants into a publicly owned treatment works must comply with 40 CFR part 403. In addition, the following pretreatment standard establishes the quantity or quality of pollutants or pollutant properties controlled by this section which may be discharged to a publicly owned treatment works by a point source subject to...

[Changes of regional environment quality pattern in China since 1986-2008].

PubMed

Guan, Wei-Hua; Sun, Ming-Kun; Lu, Yu-Qi

2011-03-01

For further study of regional differences and the pattern of changes in environmental quality in China since 1986-2008, we perform the principal component analysis, standard deviation, Mann-Kendall and cluster analysis on 18 environmental quality indexes in 28 provinces of China in this paper. Those indexes refer to pollutant emission, pollutants treatment capacities and pollutant emission of per unit land area, etc. The paper indicates that regional environmental quality in China has been increased slightly during this period. It can be divided into four stages: 1986-2000, 2000-2001, 2001-2005 and 2005-2008. The overall patterns of regional environmental quality is the West is higher than the East in general, while the environmental quality of the eastern part have been changed somewhat. For more details, the regional environmental quality in China in 1986 is composed of two parts, the eastern part and the western part, while in 2000 and 2001 the eastern part, the middle part and the western part appears as the overall pattern. For the year of 2005, the regional environmental quality in the western is higher than that of the eastern; meanwhile, the eastern can be divided into the northern part, the middle part and the southern part, and the environmental quality in northern part is better than that of the southern part, southern part is better than that of the middle part. This pattern hardly changed in 2008, except that the area with poor environment quality region had expanded. Pollutant emission of per unit land area played as a main factor; yet both the pollutant emission and the reuse of pollutants impacted the pattern specifically. In addition, the national macro policies, the regional policies, the regional economic and the industrial structure can be primary reason for the change of regional environmental quality pattern in China as well.

Water contaminations in Karaj dam's rivers and their relationship with outcrop rocks with using GIS method

NASA Astrophysics Data System (ADS)

Shadmehr, Mehdi; Bafekr, Gilava; Pirouz, Mortaza

2010-05-01

Karaj Dam is located in the middle part of Alborz Mountain and its distance from Capital city, Tehran, is 63 kilometers. Watershed area approximately is 1000 square kilometers, average rate of rainfall is 625 mm per year and watershed altitude is between 4900 to 1700 meters from open sea. Karaj Dam is as a drinking water source for Tehran and Karaj cities and 21000 hectares of agricultural irrigation. Our studies is connected with As, Pb, Sb, Hg, Mo contaminant elements . We used 194 rock samples for chemical analysis and 12 water quality control stations. Chemical analysis values of rocks in the GIS divided into different classes with regard to the standard allowable values. We used SRTM data to find major catchments area and small watershed basin area behind the dam. After the necessary calculations, we determined which small basin area can be important to make more elements to pollution. The results compared with 12 water quality control stations and direct connection between the chemical composition of the rocks and water contaminated that comes from that area are very obvious. Our Study shows that natural contaminations can be enter to cycle from the southern part of basin, 14 kilometers from dam to east. Water contaminations is located along Shahrestanak river to Shahrestanak bridge and then to Mahan factory. The catchment's area for this river has highest amount of As, Sb, Pb and water quality control stations close that area show high contamination.

Evaluation of droplet digital PCR for quantification of residual leucocytes in red blood cell concentrates.

PubMed

Doescher, A; Loges, U; Petershofen, E K; Müller, T H

2017-11-01

Enumeration of residual white blood cells in leucoreduced blood components is essential part of quality control. Digital PCR has substantially facilitated quantitative PCR and was thus evaluated for measurements of leucocytes. Target for quantification of leucocytes by digital droplet PCR was the blood group gene RHCE. The SPEF1 gene was added as internal control for the entire assay starting with automated DNA extraction. The sensitivity of the method was determined by serial dilutions of standard samples. Quality control samples were analysed within 24 h, 7 days and 6 months after collection. Routine samples from leucodepleted red blood cell concentrates (n = 150) were evaluated in parallel by flow-cytometry (LeucoCount) and by digital PCR. Digital PCR reliably detected at least 0·4 leucocytes per assay. The mean difference between PCR and flow-cytometric results from 150 units was -0·01 (±1·0). DNA samples were stable for up to at least six months. PCR measurement of leucocytes in samples from plasma and platelet concentrates also provided valid results in a pilot study. Droplet digital PCR to enumerate leucocytes offers an alternative for quality control of leucoreduced blood products. Sensitivity, specificity and reproducibility are comparable to flow-cytometry. The option to collect samples over an extended period of time and the automatization introduce attractive features for routine quality control. © 2017 International Society of Blood Transfusion.

Parts, materials, and processes experience summary, volume 2. [design, engineering, and quality control

NASA Technical Reports Server (NTRS)

1973-01-01

This summary provides the general engineering community with the accumulated experience from ALERT reports issued by NASA and the Government-Industry. Data Exchange Program, and related experience gained by Government and industry. It provides expanded information on selected topics by relating the problem area (failure) to the cause, the investigation and findings, the suggestions for avoidance (inspections, screening tests, proper part applications, requirements for manufacturer's plant facilities, etc.), and failure analysis procedures. Diodes, integrated circuits, and transistors are covered in this volume.

A comprehensive quality control workflow for paired tumor-normal NGS experiments.

PubMed

Schroeder, Christopher M; Hilke, Franz J; Löffler, Markus W; Bitzer, Michael; Lenz, Florian; Sturm, Marc

2017-06-01

Quality control (QC) is an important part of all NGS data analysis stages. Many available tools calculate QC metrics from different analysis steps of single sample experiments (raw reads, mapped reads and variant lists). Multi-sample experiments, as sequencing of tumor-normal pairs, require additional QC metrics to ensure validity of results. These multi-sample QC metrics still lack standardization. We therefore suggest a new workflow for QC of DNA sequencing of tumor-normal pairs. With this workflow well-known single-sample QC metrics and additional metrics specific for tumor-normal pairs can be calculated. The segmentation into different tools offers a high flexibility and allows reuse for other purposes. All tools produce qcML, a generic XML format for QC of -omics experiments. qcML uses quality metrics defined in an ontology, which was adapted for NGS. All QC tools are implemented in C ++ and run both under Linux and Windows. Plotting requires python 2.7 and matplotlib. The software is available under the 'GNU General Public License version 2' as part of the ngs-bits project: https://github.com/imgag/ngs-bits. christopher.schroeder@med.uni-tuebingen.de. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

Development and qualification of additively manufactured parts for space

NASA Astrophysics Data System (ADS)

O'Brien, Michael J.

2018-02-01

Additive manufacturing (commonly called "3D printing") fabricates the desired final part directly from the input CAD (Computer Aided Design) file by depositing and fusing layer upon layer of the source material. New engineering designs are possible in which a single optimized part with novel topology can replace several traditional parts. The complex physics of metal deposition leads to variations in quality and to new flaws and residual stresses not seen in traditional manufacturing. Additive manufacturing currently has gaps in knowledge. Mission assurance will require: qualification and certification standards; sharing of data in handbooks; predictive models relating processing, microstructure and properties; and development of closed loop process control and non-destructive evaluation to reduce variability.

The new production theory for health care through clinical reengineering: a study of clinical guidelines--Part II.

PubMed

Sharp, J R

1995-01-01

In Part I of this two-part article, in the December 1994 issue of the journal, the author discussed the manufacturing theories of Peter Drucker in terms of their applicability for the health care field. He concluded that Drucker's four principles and practices of manufacturing--statistical quality control, manufacturing accounting, modular organization, and systems approach--do have application to the health care system. Clinical guidelines, a variation on the Drucker theory, are a specific example of the manufacturing process in health. The performance to date of some guidelines and their implications for the health care reform debate are discussed in Part II of the article.

[Air quality control systems: heating, ventilating, and air conditioning (HVAC)].

PubMed

Bellucci Sessa, R; Riccio, G

2004-01-01

After a brief illustration of the principal layout schemes of Heating, Ventilating, and Air Conditioning (HVAC), the first part of this paper summarizes the standards, both voluntary and compulsory, regulating HVAC facilities design and installation with regard to the question of Indoor Air Quality (IAQ). The paper then examines the problem of ventilation systems maintenance and the essential hygienistic requirements in whose absence HVAC facilities may become a risk factor for people working or living in the building. Lastly, the paper deals with HVAC design strategies and methods, which aim not only to satisfy comfort and air quality requirements, but also to ensure easy and effective maintenance procedures.

Rubber dam isolation of cervical lesions. Part 1: Alternative techniques which avoid injury to the periodontium.

PubMed

Liebenberg, W H

1994-01-01

While it is arguable that the operative procedures depicted in this article could have been done equally well with alternative forms of isolation, it is indisputable that rubber dam provides for the most thorough 'isolation' in the comprehensive sense of the term. It allows for the finite control over peripheral variables such as access and controlled gingival retraction. This in turn permits meticulous execution of restorative procedures within the luxury of 'true four-handed dentistry'. Most operative procedures are done within the limitations of single handed dentistry as the other 'three hands' are involved with retraction, fluid evacuation and access control. The rubber dam is indeed indispensable and with the increased awareness of infection control it is conceivable that rubber dam isolation will continue to be associated with quality patient care. Part 2 of this article will detail the application of the 'Modified Gingival Retractor' in the isolation of cervical lesions.

The use of a non-nuclear density gauge for monitoring the compaction process of asphalt pavement

NASA Astrophysics Data System (ADS)

Van den bergh, Wim; Vuye, Cedric; Kara, Patricia; Couscheir, Karolien; Blom, Johan; Van Bouwel, Philippe

2017-09-01

The mechanical performance of an asphalt pavement affects its durability - thus carbon footprint. Many parameters contribute to the success of a durable asphalt mix, e.g. material selection, an accurate mix and even the road design in which the asphalt mix quality is quantified. The quality of the asphalt mix, by its mechanical properties, is also related to the compaction degree. However, and specifically for high volume rates, the laying process at the construction site needs an effective method to monitor and adjust immediately the compaction quality before cooling and without damaging the layer, which is now absent. In this paper the use of a non-nuclear density gauge (PQI - Pavement Quality Indicator) is evaluated, based on a site at Brussels Airport. Considering the outcome of the present research, this PQI is advised as a unique tool for continuous density measurements and allow immediate adjustments during compaction, and decreases the number of core drilling for quality control, and as a posteriori asphalt pavement density test where cores are prohibited. The use of PQI could be recommended to be a part of the standard quality control process in the Flemish region.

An approach to quality and security of supply for single-use bioreactors.

PubMed

Barbaroux, Magali; Gerighausen, Susanne; Hackel, Heiko

2014-01-01

Single-use systems (also referred to as disposables) have become a huge part of the bioprocessing industry, which raised concern in the industry regarding quality and security of supply. Processes must be in place to assure the supply and control of outsourced activities and quality of purchased materials along the product life cycle. Quality and security of supply for single-use bioreactors (SUBs) are based on a multidisciplinary approach. Developing a state-of-the-art SUB-system based on quality by design (QbD) principles requires broad expertise and know-how including the cell culture application, polymer chemistry, regulatory requirements, and a deep understanding of the biopharmaceutical industry. Using standardized products reduces the complexity and strengthens the robustness of the supply chain. Well-established supplier relations including risk mitigation strategies are the basis for achieving long-term security of supply. Well-developed quality systems including change control approaches aligned with the requirements of the biopharmaceutical industry are a key factor in supporting long-term product availability. This chapter outlines the approach to security of supply for key materials used in single-use production processes for biopharmaceuticals from a supplier perspective.

Tobacco control advocates must demand high-quality media campaigns: the California experience.

PubMed

Balbach, E D; Glantz, S A

1998-01-01

To document efforts on the part of public officials in California to soften the media campaign's attack on the tobacco industry and to analyse strategies to counter those efforts on the part of tobacco control advocates. Data were gathered from interviews with programme participants, direct observation, written materials, and media stories. In addition, internal documents were released by the state's Department of Health Services in response to requests made under the California Public Records Act by Americans for Nonsmokers' Rights. Finally, a draft of the paper was circulated to 11 key players for their comments. In 1988 california voters enacted Proposition 99, an initiative that raised the tobacco tax by $0.25 and allocated 20% of the revenues to anti-tobacco education. A media campaign, which was part of the education programme, directly attacked the tobacco industry, exposing the media campaign to politically based efforts to shut it down or soften it. Through use of outsider strategies such as advertising, press conferences, and public meetings, programme advocates were able to counter the efforts to soften the campaign. Anti-tobacco media campaigns that expose industry manipulation are a key component of an effective tobacco control programme. The effectiveness of these campaigns, however, makes them a target for elimination by the tobacco industry. The experience from California demonstrates the need for continuing, aggressive intervention by nongovernmental organisations in order to maintain the quality of anti-tobacco media campaigns.

Variation of organic matter quantity and quality in streams at Critical Zone Observatory watersheds

USGS Publications Warehouse

Miller, Matthew P.; Boyer, Elizabeth W.; McKnight, Diane M.; Brown, Michael G.; Gabor, Rachel S.; Hunsaker, Carolyn T.; Iavorivska , Lidiia; Inamdar, Shreeram; Kaplan, Louis A.; Johnson, Dale W.; Lin, Henry; McDowell, William H.; Perdrial, Julia N.

2016-01-01

The quantity and chemical composition of dissolved organic matter (DOM) in surface waters influence ecosystem processes and anthropogenic use of freshwater. However, despite the importance of understanding spatial and temporal patterns in DOM, measures of DOM quality are not routinely included as part of large-scale ecosystem monitoring programs and variations in analytical procedures can introduce artifacts. In this study, we used consistent sampling and analytical methods to meet the objective of defining variability in DOM quantity and quality and other measures of water quality in streamflow issuing from small forested watersheds located within five Critical Zone Observatory sites representing contrasting environmental conditions. Results show distinct separations among sites as a function of water quality constituents. Relationships among rates of atmospheric deposition, water quality conditions, and stream DOM quantity and quality are consistent with the notion that areas with relatively high rates of atmospheric nitrogen and sulfur deposition and high concentrations of divalent cations result in selective transport of DOM derived from microbial sources, including in-stream microbial phototrophs. We suggest that the critical zone as a whole strongly influences the origin, composition, and fate of DOM in streams. This study highlights the value of consistent DOM characterization methods included as part of long-term monitoring programs for improving our understanding of interactions among ecosystem processes as controls on DOM biogeochemistry.

[Research on chemical fingerprint chromatograms of Sinopodophyllum hexandrum].

PubMed

Wang, Ai-Hua; Liu, Guang-Xue; Xu, Feng; Shang, Ming-Ying; Cai, Shao-Qing

2013-10-01

To study the HPLC fingerprint of Sinopodophylli Fructus, compare the major chemical differences in fruit of Sinopodophyllum hexandrum as well as the roots and rhizomas of S. hexandrum, and provide scientific evidence for clinical application and quality control. HPLC fingerprint method was used to analyze 12 fruits of S. hexandrum. A total of 20 common peaks were confirmed, and 12 peaks in the HPLC fingerprint were identified. Furthermore, similarity evaluation method and clustering analysis method were introduced to compare HPLC chromatograms, between fruits and underground parts. In this paper, quercetin-3-O-beta-D-glucopyranosid, kaempferol-3-O-beta-D-glucopyranoside, 8-prenylquercetin and 8-prenylquercetin 3-methyl ether were firstly reported in Sinopodophylli Fructus. Among the existing fingerprint research, a total of 11 peaks were identified for the first time, containing 9 flavonoids and 2 lignans. The chemical constituents differed significantly in different medicinal parts of S. hexandrum. Prenylflavonoid compounds were the main constituents of Sinopodophylli Fructus. However, podophyllotoxin, flavonoids with simple substituent groups and flavonoid glycosides were the major ingredients in the roots and rhizomas of S. hexandrum. This method can be used for the quality control of Sinopodophylli Fructus and the roots and rhizomas of S. hexandrum. It has provided a reference for the pharmacodynamic differences of the two different parts.

Foot shape and its effect on functioning in Royal Australian Air Force recruits. Part 2: Pilot, randomized, controlled trial of orthotics in recruits with flat feet.

PubMed

Esterman, Adrian; Pilotto, Louis

2005-07-01

As part of a larger study of the effect of foot shape on functioning, 47 Royal Australian Air Force recruits with flexible flat feet who were embarking on a 10-week basic training course took part in a randomized controlled trial of orthotic therapy. In particular, recruits were assigned at random to an untreated group or a group that received Australian Orthotics Laboratory, three-quarter-length, flexible, shoe inserts. The groups were assessed at baseline and week 8. Outcome measures included pain, injury, foot health, and quality of life. The untreated group (n = 22) had a greater proportion of heavier recruits than did the treated group (n = 25). There were no significant differences in outcome measures at baseline. Only one-half of the group assigned to orthotic therapy wore the orthotics most or all of the time. At the end of the trial, although the results were not statistically significant, those who were provided with orthotics and wore them had the least lower limb pain and the best general foot health and quality of life. Notably, none of the recruits who wore their orthotics most or all of the time sustained a training injury.