Micro CSI: A Microbial Citizen Science Initiative in Urban Watersheds

EPA Science Inventory

Across the Nation, a number of citizen science efforts have been conducted to monitor water quality. Efforts have included monitoring of bacteriological parameters (E. coli, enterococci, and fecal coliforms) and/or physicochemical parameters (temperature, turbidity, pH, conducti...

Modeling coliform-bacteria concentrations and pH in the salt-wedge reach of the Duwamish River Estuary, King County, Washington

USGS Publications Warehouse

Haushild, W.L.; Prych, Edmund A.

1976-01-01

Total- and fecal-coliform bacteria, plus pH, alkalinity, and dissolved inorganic carbon are water-quality parameters that have been added to an existing numerical model of water quality in the salt-wedge reach of the Duwamish River estuary in Washington. The coliform bacteria are modeled using a first-order decay (death) rate, which is a function of the local salinity, temperature, and daily solar radiation. The pH is computed by solving a set of chemical-equilibrium equations for carbonate-bicarbonate buffered aqueous solutions. Concentrations of total- and fecal-coliform bacteria computed by the model for the Duwamish River estuary during June-September 1971 generally agreed with observed concentrations within about 40 and 60 percent, respectively. The computed pH generally agreed with observed pH within about a 0.2 pH unit; however, for one 3-week period the computed pH was about a 0.4 unit lower than the observed pH. (Woodard-USGS)

Effectiveness of birds, butterflies, dragonflies, damselflies and invertebrates as indicators of freshwater ecological integrity

NASA Astrophysics Data System (ADS)

Chama, Lackson; Siachoono, Stanford

2015-04-01

Human activities such as mining and agriculture are among the major threats to biodiversity globally. Discharges from these activities have been shown to negatively affect ecological processes, leading to ecosystem degradation and species loss across biomes. Freshwater systems have been shown to be particularly vulnerable, as discharges tend to spread rapidly here than in other ecosystems. Hence, there is need to routinely monitor the quality of these systems if impacts of discharges from human activities are to be minimised. Besides the use of conventional laboratory techniques, several studies have recently shown that organisms such as birds, butterflies, dragonflies, damselflies and invertebrates are also good indicators of ecological integrity and should therefore be used as alternatives to monitoring the quality of various ecosystems. However, most of these studies have only studied one or two of these organisms against ecosystem health, and it remains unclear whether all of them respond similarly to changes in different drivers of environmental change. We investigated the response of the diversity of birds, butterflies, dragonflies, damselflies and invertebrates to changing water quality along the Kafue River in Zambia. Sampling was done at 13 different sampling points stretching over a distance of 60Km along the river. At each point, both the diversity of each organism and the water quality were assessed. Water quality was determined by testing its temperature, pH, redox, electrical conductivity, turbidity and copper parameters. We then tested how the diversity of each organism responded to changes in these water parameters. All water parameters varied significantly across sampling points. The diversity of birds and damselflies remained unaffected by any of the water parameters used. However, the diversity of butterflies reduced with increasing pH, turbidity and copper, albeit it remained unaffected by other water parameters. The diversity of dragonflies reduced with increasing redox, electrical conductivity and turbidity, but remained unaffected by other water parameters. The diversity of invertebrates reduced with increasing redox and copper, but remained unaffected by other water parameters. Generally, these results suggest that these organisms, especially butterflies, dragonflies and invertebrates can indeed be used as indicators of changing water quality and ecological integrity in particular. However, their use is limited to specific, rather than, all water parameters. Therefore, the decision as to which organisms to use should largely depend on which water quality parameters are to be tested. Key words: temperature; pH; redox; electrical conductivity; turbidity; copper

40 CFR 133.102 - Secondary treatment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... effluent quality attainable by secondary treatment in terms of the parameters—BOD5, SS and pH. All... permitting authority, in lieu of the parameter BOD5 and the levels of the effluent quality specified in... CBOD5 effluent quality provided: (i) The 30-day average shall not exceed 25 mg/l. (ii) The 7-day average...

Water and sediment quality parameters in the Chalan Beel, the largest wetland of Bangladesh

NASA Astrophysics Data System (ADS)

Sayeed, Md. Abu; Hossain, Mostafa Ali Reza; Wahab, Md. Abdul; Hasan, Md. Tawheed; Simon, Kumar Das; Mazumder, Sabuj Kanti

2015-07-01

A study was conducted to investigate the status of the water and sediment quality in the Chalan Beel-a major fresh water fish reservoir of the country for a period of one year from July 2007 to June 2008. The mean values of water quality parameters (depth: 214.73±152.22 cm, temperature 27.68±4.26°C, transparency 123±82 cm, pH 9.7±0.47, total alkalinity 137±42 mg/L, conductivity 307±147 μs/cm, total dissolved solids 183±89 mg/L, ammonia-N 0.27±0.39 mg/L, nitrate-N 0.09±0.07 mg/L, phosphate-P 2.01±2.53 mg/L) and sediment quality parameters (pH 7.21±0.35, organic matter 2.59±0.52%, total nitrogen 0.09±0.04%, available phosphorus 5.4±3.6 Meq./100 g and exchangeable potassium 0.43±0.14 Meq./100 g) were within the range recommended for most of the inland fishes of Bangladesh. Although the water and sediment quality parameters except ammonia and phosphate are in the suitable range, the overall results suggest that better management techniques should be practiced in order to overcome the declining trend of associated aquatic life (fauna and flora) of this important fresh water body of Bangladesh.

Assessing groundwater quality for irrigation using indicator kriging method

NASA Astrophysics Data System (ADS)

Delbari, Masoomeh; Amiri, Meysam; Motlagh, Masoud Bahraini

2016-11-01

One of the key parameters influencing sprinkler irrigation performance is water quality. In this study, the spatial variability of groundwater quality parameters (EC, SAR, Na+, Cl-, HCO3 - and pH) was investigated by geostatistical methods and the most suitable areas for implementation of sprinkler irrigation systems in terms of water quality are determined. The study was performed in Fasa county of Fars province using 91 water samples. Results indicated that all parameters are moderately to strongly spatially correlated over the study area. The spatial distribution of pH and HCO3 - was mapped using ordinary kriging. The probability of concentrations of EC, SAR, Na+ and Cl- exceeding a threshold limit in groundwater was obtained using indicator kriging (IK). The experimental indicator semivariograms were often fitted well by a spherical model for SAR, EC, Na+ and Cl-. For HCO3 - and pH, an exponential model was fitted to the experimental semivariograms. Probability maps showed that the risk of EC, SAR, Na+ and Cl- exceeding the given critical threshold is higher in lower half of the study area. The most proper agricultural lands for sprinkler irrigation implementation were identified by evaluating all probability maps. The suitable areas for sprinkler irrigation design were determined to be 25,240 hectares, which is about 34 percent of total agricultural lands and are located in northern and eastern parts. Overall the results of this study showed that IK is an appropriate approach for risk assessment of groundwater pollution, which is useful for a proper groundwater resources management.

Statistical analysis of porosity of 17-4PH alloy processed by selective laser melting

NASA Astrophysics Data System (ADS)

Ponnusamy, P.; Masood, S. H.; Ruan, D.; Palanisamy, S.; Mohamed, O. A.

2017-07-01

Selective Laser Melting (SLM) is a powder-bed type Additive Manufacturing (AM) process, where parts are built layer-by-layer by laser melting of powder layers of metal. There are several SLM process parameters that affect the accuracy and quality of the metal parts produced by SLM. Therefore, it is essential to understand the effect of these parameters on the quality and properties of the parts built by this process. In this paper, using Taguchi design of experiments, the effect of four SLM process parameters namely laser power, defocus distance, layer thickness and build orientation are considered on the porosity of 17-4PH stainless steel parts built on ProX200 SLM direct metal printer. The porositywas found to be optimum at a defocus distance of -4mm and a laser power of 240 W with a layer thickness of 30 μm and using vertical build orientation.

Different Statistical Approaches to Investigate Porcine Muscle Metabolome Profiles to Highlight New Biomarkers for Pork Quality Assessment

PubMed Central

Welzenbach, Julia; Neuhoff, Christiane; Looft, Christian; Schellander, Karl; Tholen, Ernst; Große-Brinkhaus, Christine

2016-01-01

The aim of this study was to elucidate the underlying biochemical processes to identify potential key molecules of meat quality traits drip loss, pH of meat 1 h post-mortem (pH1), pH in meat 24 h post-mortem (pH24) and meat color. An untargeted metabolomics approach detected the profiles of 393 annotated and 1,600 unknown metabolites in 97 Duroc × Pietrain pigs. Despite obvious differences regarding the statistical approaches, the four applied methods, namely correlation analysis, principal component analysis, weighted network analysis (WNA) and random forest regression (RFR), revealed mainly concordant results. Our findings lead to the conclusion that meat quality traits pH1, pH24 and color are strongly influenced by processes of post-mortem energy metabolism like glycolysis and pentose phosphate pathway, whereas drip loss is significantly associated with metabolites of lipid metabolism. In case of drip loss, RFR was the most suitable method to identify reliable biomarkers and to predict the phenotype based on metabolites. On the other hand, WNA provides the best parameters to investigate the metabolite interactions and to clarify the complex molecular background of meat quality traits. In summary, it was possible to attain findings on the interaction of meat quality traits and their underlying biochemical processes. The detected key metabolites might be better indicators of meat quality especially of drip loss than the measured phenotype itself and potentially might be used as bio indicators. PMID:26919205

Mapping of fluoride endemic areas and correlation studies of fluoride with other quality parameters of drinking water of Veppanapalli block of Dharmapuri district in Tamil Nadu.

PubMed

Karthikeyan, G; Sundarraj, A Shunmuga; Elango, K P

2003-10-01

193 drinking water samples from water sources of 27 panchayats of Veppanapalli block of Dharmapuri district of Tamil Nadu were analysed for chemical quality parameters. Based on the fluoride content of the water sources, fluoride maps differentiating regions with high / low fluoride levels were prepared using Isopleth mapping technique. The interdependence among the important chemical quality parameters were assessed using correlation studies. The experimental results of the application of linear and multiple regression equations on the influence of hardness, alkalinity, total dissolved solids and pH on fluoride are discussed.

Prediction of harmful water quality parameters combining weather, air quality and ecosystem models with in situ measurement

EPA Science Inventory

The ability to predict water quality in lakes is important since lakes are sources of water for agriculture, drinking, and recreational uses. Lakes are also home to a dynamic ecosystem of lacustrine wetlands and deep waters. They are sensitive to pH changes and are dependent on d...

Factors influencing lead and iron release from some Egyptian drinking water pipes.

PubMed

Lasheen, M R; Sharaby, C M; El-Kholy, N G; Elsherif, I Y; El-Wakeel, S T

2008-12-30

The major objective of this study is to assess the effect of stagnation time, pipe age, pipes material and water quality parameters such as pH, alkalinity and chloride to sulfate mass ratio on lead and iron release from different types of water pipes used in Egypt namely polyvinyl chloride (PVC), polypropylene (PP) and galvanized iron (GI), by using fill and dump method. Low pH increased lead and iron release from pipes. Lead and iron release decreased as pH and alkalinity increased. Lead and iron release increased with increasing chloride to sulfate mass ratio in all pipes. EDTA was used as an example of natural organic matter which may be influence metals release. It is found that lead and iron release increased then this release decreased with time. In general, GI pipes showed to be the most effected by water quality parameters tested and the highest iron release. PVC pipes are the most lead releasing pipes while PP pipes are the least releasing.

The level of heat shock protein 90 in pig Longissimus dorsi muscle and its relationship with meat pH and quality.

PubMed

Zhang, Muhan; Wang, Daoying; Geng, Zhiming; Bian, Huan; Liu, Fang; Zhu, Yongzhi; Xu, Weimin

2014-12-15

The 90 kDa heat shock protein (HSP90) is a molecular chaperone that participates in various cellular processes, the role and significance of HSP90 in postmortem muscle though remains unclear. In the present study, pig Longissimus dorsi muscles, categorized into three pH groups, were tested for HSP90 levels and meat quality parameters (i.e. water holding capacity, colour, tenderness and lipid oxidation). The muscles with a high initial pH (pHi) group (pH>6.4) possessing the greatest water holding capacity and lightness, contained the highest HSP90 level, followed by intermediate (6.0-6.4) and low pHi groups (pH<6.0). Statistical analysis indicated HSP90 level was significantly and negatively correlated with cooking loss, drip loss, and lightness (r=-0.797, -0.785, -0.604, respectively, P<0.01). The results suggest that HSP90 may play a crucial role in water retention of meat and may be involved in postmortem meat quality development. Copyright © 2014 Elsevier Ltd. All rights reserved.

Groundwater quality from a part of Prakasam District, Andhra Pradesh, India

NASA Astrophysics Data System (ADS)

Subba Rao, N.

2018-03-01

Quality of groundwater is assessed from a part of Prakasam district, Andhra Pradesh, India. Groundwater samples collected from thirty locations from the study area were analysed for pH, electrical conductivity (EC), total dissolved solids (TDS), calcium (Ca2+), magnesium (Mg2+), sodium (Na+), potassium (K+), bicarbonate ( {HCO}3^{ - } ), chloride (Cl-), sulphate ( {SO}4^{2 - } ), nitrate ( {NO}3^{ - } ) and fluoride (F-). The results of the chemical analysis indicate that the groundwater is alkaline in nature and are mainly characterized by Na+- {HCO}3^{ - } and Na+-Cl- facies. Groundwater chemistry reflects the dominance of rock weathering and is subsequently modified by human activities, which are supported by genetic geochemical evolution and hydrogeochemical relations. Further, the chemical parameters (pH, TDS, Ca2+, Mg2+, Na+, {HCO}3^{ - } , Cl-, {SO}4^{2 - } , {NO}3^{ - } and F-) were compared with the drinking water quality standards. The sodium adsorption ratio, percent sodium, permeability index, residual sodium carbonate, magnesium ratio and Kelly's ratio were computed and USSL, Wilcox and Doneen's diagrams were also used for evaluation of groundwater quality for irrigation. For industrial purpose, the pH, TDS, {HCO}3^{ - } , Cl- and {SO}4^{2 - } were used to assess the impact of incrustation and corrosion activities on metal surfaces. As a whole, it is observed that the groundwater quality is not suitable for drinking, irrigation and industrial purposes due to one or more chemical parameters exceeding their standard limits. Therefore, groundwater management measures were suggested to improve the water quality.

CARINA data synthesis project: pH data scale unification and cruise adjustments

NASA Astrophysics Data System (ADS)

Velo, A.; Pérez, F. F.; Lin, X.; Key, R. M.; Tanhua, T.; de La Paz, M.; Olsen, A.; van Heuven, S.; Jutterström, S.; Ríos, A. F.

2010-05-01

Data on carbon and carbon-relevant hydrographic and hydrochemical parameters from 188 previously non-publicly available cruise data sets in the Artic Mediterranean Seas (AMS), Atlantic Ocean and Southern Ocean have been retrieved and merged to a new database: CARINA (CARbon IN the Atlantic Ocean). These data have gone through rigorous quality control (QC) procedures to assure the highest possible quality and consistency. The data for most of the measured parameters in the CARINA database were objectively examined in order to quantify systematic differences in the reported values. Systematic biases found in the data have been corrected in the data products, three merged data files with measured, calculated and interpolated data for each of the three CARINA regions; AMS, Atlantic Ocean and Southern Ocean. Out of a total of 188 cruise entries in the CARINA database, 59 reported pH measured values. All reported pH data have been unified to the Sea-Water Scale (SWS) at 25 °C. Here we present details of the secondary QC of pH in the CARINA database and the scale unification to SWS at 25 °C. The pH scale has been converted for 36 cruises. Procedures of quality control, including crossover analysis between cruises and inversion analysis are described. Adjustments were applied to the pH values for 21 of the cruises in the CARINA dataset. With these adjustments the CARINA database is consistent both internally as well as with the GLODAP data, an oceanographic data set based on the World Hydrographic Program in the 1990s. Based on our analysis we estimate the internal consistency of the CARINA pH data to be 0.005 pH units. The CARINA data are now suitable for accurate assessments of, for example, oceanic carbon inventories and uptake rates, for ocean acidification assessment and for model validation.

Assessment of roadside surface water quality of Savar, Dhaka, Bangladesh using GIS and multivariate statistical techniques

NASA Astrophysics Data System (ADS)

Ahmed, Fahad; Fakhruddin, A. N. M.; Imam, MD. Toufick; Khan, Nasima; Abdullah, Abu Tareq Mohammad; Khan, Tanzir Ahmed; Rahman, Md. Mahfuzur; Uddin, Mohammad Nashir

2017-11-01

In this study, multivariate statistical techniques in collaboration with GIS are used to assess the roadside surface water quality of Savar region. Nineteen water samples were collected in dry season and 15 water quality parameters including TSS, TDS, pH, DO, BOD, Cl-, F-, NO3 2-, NO2 -, SO4 2-, Ca, Mg, K, Zn and Pb were measured. The univariate overview of water quality parameters are TSS 25.154 ± 8.674 mg/l, TDS 840.400 ± 311.081 mg/l, pH 7.574 ± 0.256 pH unit, DO 4.544 ± 0.933 mg/l, BOD 0.758 ± 0.179 mg/l, Cl- 51.494 ± 28.095 mg/l, F- 0.771 ± 0.153 mg/l, NO3 2- 2.211 ± 0.878 mg/l, NO2 - 4.692 ± 5.971 mg/l, SO4 2- 69.545 ± 53.873 mg/l, Ca 48.458 ± 22.690 mg/l, Mg 19.676 ± 7.361 mg/l, K 12.874 ± 11.382 mg/l, Zn 0.027 ± 0.029 mg/l, Pb 0.096 ± 0.154 mg/l. The water quality data were subjected to R-mode PCA which resulted in five major components. PC1 explains 28% of total variance and indicates the roadside and brick field dust settle down (TDS, TSS) in the nearby water body. PC2 explains 22.123% of total variance and indicates the agricultural influence (K, Ca, and NO2 -). PC3 describes the contribution of nonpoint pollution from agricultural and soil erosion processes (SO4 2-, Cl-, and K). PC4 depicts heavy positively loaded by vehicle emission and diffusion from battery stores (Zn, Pb). PC5 depicts strong positive loading of BOD and strong negative loading of pH. Cluster analysis represents three major clusters for both water parameters and sampling sites. The site based on cluster showed similar grouping pattern of R-mode factor score map. The present work reveals a new scope to monitor the roadside water quality for future research in Bangladesh.

The impact of primary packaging on the quality of parenteral products.

PubMed

Solomun, Ljiljana; Ibric, Svetlana; Boltic, Zorana; Djuric, Zorica; Stupar, Biljana

2008-11-04

The unique approach in manufacturing of pharmaceutical dosage forms of active substances known to be unstable in aqueous solution is the introduction of lyophilization process. Nevertheless, these products must be reconstituted using the diluent from a separate container before application. The possible solution for this problem is the application of dual chamber vials comprising the freeze-dried product in a lower compartment of the vial and the solution for reconstitution in the upper chamber. The main issue in development of such product is the choice of contact packaging (rubber closures, glass vials and the container closure system as a whole). The most important parameter used for evaluation of the influence of contact material on product quality was the pH value. The results have shown that the type of vials (moulded or tubular glass) has no impact on pH shift of the solution for reconstitution (tested solution-TS), while significant differences in pH value of the TS were observed depending on the rubber closures formulation used (with some formulations, the pH shift during the test was 6.5-9.14). Benzyl alcohol assay during the tests remained unchanged. Integrity tests of the container closure system (CCS) have demonstrated the adequacy of the selected packaging system. The quality of the CCS of choice was confirmed in the course of stability studies, only parameters directly influenced by CCS being presented in this work: loss on drying and pH value. On the basis of these results, no changes in loss on drying were connected to CCS, and the pH value of the reconstituted solution remains unchanged in samples tested both ex-tempore and after in-use period of 48 h.

Comparative study on five different commercial extenders for boar semen.

PubMed

Vyt, P; Maes, D; Dejonckheere, E; Castryck, F; Van Soom, A

2004-02-01

Increasing interest in a longer preservation of diluted boar sperm raises questions in the field concerning the choice of the extender. The aim of this study was to evaluate the longevity of boar sperm extended in currently used commercial semen extenders. Three long-term extenders and two short-term extenders were compared for different semen quality parameters that can be assessed under routine laboratory conditions. Sperm morphology, motility, pH and bacteriological contamination were investigated during a 7-day period. The number of dead spermatozoa did not differ significantly among the extenders (p > 0.05). Sperm motility was not only related with storage period but most of all with pH, especially in long-term extenders. Differences between the different extenders were prominent (p < 0.05); the sperm preserved in only one long-term extender showed good motility during the whole test period. In all cases, the pH of the extended semen increased by 0.3-0.5 in the first days of storage and was significantly correlated with a decrease in motility. Bacteriological quality had no significant influence on motility or pH of the semen. In conclusion, we can state that in both short-term extenders and in only one long-term extender, sperm longevity, as evaluated by the parameters used in this study, was sufficient during the preservation period. To preserve the quality of diluted boar semen during long-term storage, the choice of the long-term extender is important. In addition, the monitoring of the pH of extended boar semen in our study emphasizes the importance of the buffering capacity of semen extenders.

Water Quality Index for measuring drinking water quality in rural Bangladesh: a cross-sectional study.

PubMed

Akter, Tahera; Jhohura, Fatema Tuz; Akter, Fahmida; Chowdhury, Tridib Roy; Mistry, Sabuj Kanti; Dey, Digbijoy; Barua, Milan Kanti; Islam, Md Akramul; Rahman, Mahfuzar

2016-02-09

Public health is at risk due to chemical contaminants in drinking water which may have immediate health consequences. Drinking water sources are susceptible to pollutants depending on geological conditions and agricultural, industrial, and other man-made activities. Ensuring the safety of drinking water is, therefore, a growing problem. To assess drinking water quality, we measured multiple chemical parameters in drinking water samples from across Bangladesh with the aim of improving public health interventions. In this cross-sectional study conducted in 24 randomly selected upazilas, arsenic was measured in drinking water in the field using an arsenic testing kit and a sub-sample was validated in the laboratory. Water samples were collected to test water pH in the laboratory as well as a sub-sample of collected drinking water was tested for water pH using a portable pH meter. For laboratory testing of other chemical parameters, iron, manganese, and salinity, drinking water samples were collected from 12 out of 24 upazilas. Drinking water at sample sites was slightly alkaline (pH 7.4 ± 0.4) but within acceptable limits. Manganese concentrations varied from 0.1 to 5.5 mg/L with a median value of 0.2 mg/L. The median iron concentrations in water exceeded WHO standards (0.3 mg/L) at most of the sample sites and exceeded Bangladesh standards (1.0 mg/L) at a few sample sites. Salinity was relatively higher in coastal districts. After laboratory confirmation, arsenic concentrations were found higher in Shibchar (Madaripur) and Alfadanga (Faridpur) compared to other sample sites exceeding WHO standard (0.01 mg/L). Of the total sampling sites, 33 % had good-quality water for drinking based on the Water Quality Index (WQI). However, the majority of the households (67 %) used poor-quality drinking water. Higher values of iron, manganese, and arsenic reduced drinking water quality. Awareness raising on chemical contents in drinking water at household level is required to improve public health.

Quantitative Determination of Spring Water Quality Parameters via Electronic Tongue.

PubMed

Carbó, Noèlia; López Carrero, Javier; Garcia-Castillo, F Javier; Tormos, Isabel; Olivas, Estela; Folch, Elisa; Alcañiz Fillol, Miguel; Soto, Juan; Martínez-Máñez, Ramón; Martínez-Bisbal, M Carmen

2017-12-25

The use of a voltammetric electronic tongue for the quantitative analysis of quality parameters in spring water is proposed here. The electronic voltammetric tongue consisted of a set of four noble electrodes (iridium, rhodium, platinum, and gold) housed inside a stainless steel cylinder. These noble metals have a high durability and are not demanding for maintenance, features required for the development of future automated equipment. A pulse voltammetry study was conducted in 83 spring water samples to determine concentrations of nitrate (range: 6.9-115 mg/L), sulfate (32-472 mg/L), fluoride (0.08-0.26 mg/L), chloride (17-190 mg/L), and sodium (11-94 mg/L) as well as pH (7.3-7.8). These parameters were also determined by routine analytical methods in spring water samples. A partial least squares (PLS) analysis was run to obtain a model to predict these parameter. Orthogonal signal correction (OSC) was applied in the preprocessing step. Calibration (67%) and validation (33%) sets were selected randomly. The electronic tongue showed good predictive power to determine the concentrations of nitrate, sulfate, chloride, and sodium as well as pH and displayed a lower R² and slope in the validation set for fluoride. Nitrate and fluoride concentrations were estimated with errors lower than 15%, whereas chloride, sulfate, and sodium concentrations as well as pH were estimated with errors below 10%.

Evaluation of multivariate linear regression and artificial neural networks in prediction of water quality parameters

PubMed Central

2014-01-01

This paper examined the efficiency of multivariate linear regression (MLR) and artificial neural network (ANN) models in prediction of two major water quality parameters in a wastewater treatment plant. Biochemical oxygen demand (BOD) and chemical oxygen demand (COD) as well as indirect indicators of organic matters are representative parameters for sewer water quality. Performance of the ANN models was evaluated using coefficient of correlation (r), root mean square error (RMSE) and bias values. The computed values of BOD and COD by model, ANN method and regression analysis were in close agreement with their respective measured values. Results showed that the ANN performance model was better than the MLR model. Comparative indices of the optimized ANN with input values of temperature (T), pH, total suspended solid (TSS) and total suspended (TS) for prediction of BOD was RMSE = 25.1 mg/L, r = 0.83 and for prediction of COD was RMSE = 49.4 mg/L, r = 0.81. It was found that the ANN model could be employed successfully in estimating the BOD and COD in the inlet of wastewater biochemical treatment plants. Moreover, sensitive examination results showed that pH parameter have more effect on BOD and COD predicting to another parameters. Also, both implemented models have predicted BOD better than COD. PMID:24456676

Rapid non-destructive assessment of pork edible quality by using VIS/NIR spectroscopic technique

NASA Astrophysics Data System (ADS)

Zhang, Leilei; Peng, Yankun; Dhakal, Sagar; Song, Yulin; Zhao, Juan; Zhao, Songwei

2013-05-01

The objectives of this research were to develop a rapid non-destructive method to evaluate the edible quality of chilled pork. A total of 42 samples were packed in seal plastic bags and stored at 4°C for 1 to 21 days. Reflectance spectra were collected from visible/near-infrared spectroscopy system in the range of 400nm to 1100nm. Microbiological, physicochemical and organoleptic characteristics such as the total viable counts (TVC), total volatile basic-nitrogen (TVB-N), pH value and color parameters L* were determined to appraise pork edible quality. Savitzky-Golay (SG) based on five and eleven smoothing points, Multiple Scattering Correlation (MSC) and first derivative pre-processing methods were employed to eliminate the spectra noise. The support vector machines (SVM) and partial least square regression (PLSR) were applied to establish prediction models using the de-noised spectra. A linear correlation was developed between the VIS/NIR spectroscopy and parameters such as TVC, TVB-N, pH and color parameter L* indexes, which could gain prediction results with Rv of 0.931, 0.844, 0.805 and 0.852, respectively. The results demonstrated that VIS/NIR spectroscopy technique combined with SVM possesses a powerful assessment capability. It can provide a potential tool for detecting pork edible quality rapidly and non-destructively.

Analytical Quality by Design in pharmaceutical quality assurance: Development of a capillary electrophoresis method for the analysis of zolmitriptan and its impurities.

PubMed

Orlandini, Serena; Pasquini, Benedetta; Caprini, Claudia; Del Bubba, Massimo; Pinzauti, Sergio; Furlanetto, Sandra

2015-11-01

A fast and selective CE method for the determination of zolmitriptan (ZOL) and its five potential impurities has been developed applying the analytical Quality by Design principles. Voltage, temperature, buffer concentration, and pH were investigated as critical process parameters that can influence the critical quality attributes, represented by critical resolution values between peak pairs, analysis time, and peak efficiency of ZOL-dimer. A symmetric screening matrix was employed for investigating the knowledge space, and a Box-Behnken design was used to evaluate the main, interaction, and quadratic effects of the critical process parameters on the critical quality attributes. Contour plots were drawn highlighting important interactions between buffer concentration and pH, and the gained information was merged into the sweet spot plots. Design space (DS) was established by the combined use of response surface methodology and Monte Carlo simulations, introducing a probability concept and thus allowing the quality of the analytical performances to be assured in a defined domain. The working conditions (with the interval defining the DS) were as follows: BGE, 138 mM (115-150 mM) phosphate buffer pH 2.74 (2.54-2.94); temperature, 25°C (24-25°C); voltage, 30 kV. A control strategy was planned based on method robustness and system suitability criteria. The main advantages of applying the Quality by Design concept consisted of a great increase of knowledge of the analytical system, obtained throughout multivariate techniques, and of the achievement of analytical assurance of quality, derived by probability-based definition of DS. The developed method was finally validated and applied to the analysis of ZOL tablets. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Water quality management using statistical analysis and time-series prediction model

NASA Astrophysics Data System (ADS)

Parmar, Kulwinder Singh; Bhardwaj, Rashmi

2014-12-01

This paper deals with water quality management using statistical analysis and time-series prediction model. The monthly variation of water quality standards has been used to compare statistical mean, median, mode, standard deviation, kurtosis, skewness, coefficient of variation at Yamuna River. Model validated using R-squared, root mean square error, mean absolute percentage error, maximum absolute percentage error, mean absolute error, maximum absolute error, normalized Bayesian information criterion, Ljung-Box analysis, predicted value and confidence limits. Using auto regressive integrated moving average model, future water quality parameters values have been estimated. It is observed that predictive model is useful at 95 % confidence limits and curve is platykurtic for potential of hydrogen (pH), free ammonia, total Kjeldahl nitrogen, dissolved oxygen, water temperature (WT); leptokurtic for chemical oxygen demand, biochemical oxygen demand. Also, it is observed that predicted series is close to the original series which provides a perfect fit. All parameters except pH and WT cross the prescribed limits of the World Health Organization /United States Environmental Protection Agency, and thus water is not fit for drinking, agriculture and industrial use.

Water quality assessment of sacred glacial Lake Satopanth of Garhwal Himalaya, India

NASA Astrophysics Data System (ADS)

Sharma, Ramesh C.; Kumar, Rahul

2017-12-01

Satopanth Lake is a glacial lake, located at an altitude of 4600 m above sea level in Garhwal Himalaya of Uttarakhand state in India where an attempt was made to assess the water quality. A total of sixteen physico-chemical parameters including temperature, hardness, alkalinity, dissolved oxygen, conductivity, pH, calcium, magnesium, chlorides, nitrates, sulphates and phosphates were recorded during 2014 and 2015 between June and August in ice-free period. The mean values of pH ranged from 6.85 to 7.10; water temperature fluctuated from 0.1 to 0.3 °C; dissolved oxygen varied from 5.90 to 6.0 mg.L-1; free CO2 varied from 8.40 to 8.60 mg.L-1; total dissolved solids varied from 88.0 to 89.5 mg.L-1; calcium from 7.88 to 7.95 mg.L-1; magnesium from 0.53 to 0.66 mg.L-1. All the physico-chemical values were within the prescribed WHO/BIS limit for drinking water. Water Quality Index (WQI) calculated based on these parameters also revealed the excellent quality of lake water.

Water quality parameters of harbors of Charlotte Amalie, St. Thomas, Virgin Islands: Acquisition of in situ water data, intercorrelation of selected water parameters, and initial correlation of these in situ biological, chemical and physical data with ERTS-1 bulk CCT MSS band 5 data

NASA Technical Reports Server (NTRS)

Coulbourn, W. C.; Olsen, D. A. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Remote sensing by the ERTS-1 satellite was compared with selected water quality parameters including pH, salinity, conductivity, dissolved oxygen, water depth, water temperature, turbidity, plankton concentration, current variables, chlorophylla, total carotenoids, and species diversity of the benthic community. Strong correlation between turbidity and MSS-sensed radiance was recorded and less strong correlations between the two plankton pigments and radiance. Turbidity and benthic species diversity were highly correlated furnishing an inferential tie between an easily sensed water quality variable and a sensitive indicator of average water quality conditions.

Potable groundwater quality in some villages of Haryana, India: focus on fluoride.

PubMed

Bishnoi, Mukul; Arora, Shalu

2007-04-01

The fluoride concentration in ground water was determined in ten villages of Rohtak district of Haryana state (India). The fluoride concentration in the underground water of these villages varied from 0.034-2.09 mg/l. Various other water quality parameters, viz., pH, electrical conductivity, total dissolved salts, total hardness, total alkalinity sodium, potassium, calcium, magnesium, carbonate, bicarbonate, chloride and sulfate were also measured. A systematic calculation of correlation coefficients among different physicochemical parameters indicated considerable variations among the analyzed samples with respect to their chemical composition. Majority of the samples do not comply with Indian as well as WHO standards for most of the water quality parameters measured. Overall water quality was found unsatisfactory for drinking purposes. Fluoride content was higher than permissible limit in 50% samples.

Ocean acidification buffering effects of seagrass in Tampa Bay

USGS Publications Warehouse

Yates, Kimberly K.; Moyer, Ryan P.; Moore, Christopher; Tomasko, David A.; Smiley, Nathan A.; Torres-Garcia, Legna; Powell, Christina E.; Chappel, Amanda R.; Bociu, Ioana; Smiley, Nathan; Torres-Garcia, Legna M.; Powell, Christina E.; Chappel, Amanda R.; Bociu, Ioana

2016-01-01

The Intergovernmental Panel on Climate Change has identified ocean acidification as a critical threat to marine and estuarine species in ocean and coastal ecosystems around the world. However, seagrasses are projected to benefit from elevated atmospheric pCO2, are capable of increasing seawater pH and carbonate mineral saturation states through photosynthesis, and may help buffer against the chemical impacts of ocean acidification. Additionally, dissolution of carbonate sediments may also provide a mechanism for buffering seawater pH. Long-term water quality monitoring data from the Environmental Protection Commission of Hillsborough County indicates that seawater pH has risen since the 1980‘s as seagrass beds have continued to recover since that time. We examined the role of seagrass beds in maintaining and elevating pH and carbonate mineral saturation state in northern and southern Tampa Bay where the percent of carbonate sediments is low (<3%) and high (>40%), respectively. Basic water quality and carbonate system parameters (including pH, total alkalinity, dissolved inorganic carbon, partial pressure of CO2, and carbonate mineral saturation state) were measured over diurnal time periods along transects (50-100 m) including dense and sparse Thalassia testudinum. seagrass beds, deep edge seagrass, and adjacent bare sand bottom. Seagrass density and productivity, sediment composition and hydrodynamic parameters were also measured, concurrently. Results indicate that seagrass beds locally elevate pH by up to 0.5 pH unit and double carbonate mineral saturation states relative to bare sand habitats. Thus, seagrass beds in Tampa Bay may provide refuge for marine organisms from the impacts of ocean acidification.

Water Quality of Hills Water, Supply Water and RO Water Machine at Ulu Yam Selangor

NASA Astrophysics Data System (ADS)

Ngadiman, N.; ‘I Bahari, N.; Kaamin, M.; Hamid, N. B.; Mokhtar, M.; Sahat, S.

2016-07-01

The rapid development resulted in the deterioration of the quality of drinking water in Malaysia. Recognizing the importance of water quality, new alternatives for drinking water such as mineral water processing from reverse osmosis (RO) machine become more popular. Hence, the demand for mineral water, natural spring water or water from the hills or mountains rose lately. More consumers believed the quality of these spring water better than other source of drinking water. However, the quality of all the drinking water sources is to meet the required quality standard. Therefore, this paper aims to measure the quality of the waters from hills, from RO machine and the water supply in Ulu Yam, Selangor Batang Kali, Malaysia. The water quality was determined based on following parameters: ammoniacal nitrogen (NH3), iron (Fe), turbidity (NTU) and pH. The results show that the water from hills has better quality compared to water supply and water from RO machine. The value of NH3 ranged from 0.03 mg/L- 0.67 mg/L; Fe was from 0.03mg/L - 0.12 mg/L, turbidity at 0.42 NTU - 0.88 NTU and pH is at 6.60 - 0.71. Based on the studied parameters, all three types of water are fit for drinking and have met the required national drinking water quality standard.

Integrated hydraulic and organophosphate pesticide injection simulations for enhancing event detection in water distribution systems.

PubMed

Schwartz, Rafi; Lahav, Ori; Ostfeld, Avi

2014-10-15

As a complementary step towards solving the general event detection problem of water distribution systems, injection of the organophosphate pesticides, chlorpyrifos (CP) and parathion (PA), were simulated at various locations within example networks and hydraulic parameters were calculated over 24-h duration. The uniqueness of this study is that the chemical reactions and byproducts of the contaminants' oxidation were also simulated, as well as other indicative water quality parameters such as alkalinity, acidity, pH and the total concentration of free chlorine species. The information on the change in water quality parameters induced by the contaminant injection may facilitate on-line detection of an actual event involving this specific substance and pave the way to development of a generic methodology for detecting events involving introduction of pesticides into water distribution systems. Simulation of the contaminant injection was performed at several nodes within two different networks. For each injection, concentrations of the relevant contaminants' mother and daughter species, free chlorine species and water quality parameters, were simulated at nodes downstream of the injection location. The results indicate that injection of these substances can be detected at certain conditions by a very rapid drop in Cl2, functioning as the indicative parameter, as well as a drop in alkalinity concentration and a small decrease in pH, both functioning as supporting parameters, whose usage may reduce false positive alarms. Copyright © 2014 Elsevier Ltd. All rights reserved.

Maggie Creek Water Quality Data

EPA Pesticide Factsheets

These data are standard water quality parameters collected for surface water condition analysis (for example pH, conductivity, DO, TSS).This dataset is associated with the following publication:Kozlowski, D., R. Hall , S. Swanson, and D. Heggem. Linking Management and Riparian Physical Functions to Water Quality and Aquatic Habitat. JOURNAL OF WATER RESOURCES PLANNING AND MANAGEMENT. American Society of Civil Engineers (ASCE), Reston, VA, USA, 8(8): 797-815, (2016).

Is the quality of drinking water a risk factor for self-reported forearm fractures? Cohort of Norway.

PubMed

Dahl, C; Søgaard, A J; Tell, G S; Flaten, T P; Krogh, T; Aamodt, G

2013-02-01

Compared to pH ≥7.0 in Norwegian municipal drinking water, pH <7.0 increased the risk of forearm fractures in the population-based Cohort of Norway (CONOR; n = 127,272). The association was attenuated (p > 0.05) after adjustments for indicators of bacteria and organic matter, which may signify an association between poor drinking water and bone health. The Norwegian population has the highest rate of fractures ever reported. A large variation in fracture rate both between and within countries indicates that an environmental factor, such as the quality of drinking water, could be one of the causes of the disparities. Our aim was to investigate a possible association between pH (an important parameter for water quality) and self-reported forearm fracture and to examine whether other water quality factors could account for this association. Using Geographic Information Systems, information on the quality of drinking water was linked to CONOR (n = 127,272; mean age, 50.2 ± 15.8 years), a database comprising ten regional epidemiological health surveys from across the country in the time period 1994-2003. The highest risk of forearm fracture was found at a pH of around 6.75, with a decreasing risk toward both higher and lower pH values. The increased adjusted odds of forearm fracture in men consuming municipal drinking water with pH <7.0 compared to water with pH ≥7.0 was odds ratio (OR) = 1.19 (95 % CI, 1.14, 1.25), and the corresponding increased odds in women was OR = 1.14 (95 % CI, 1.08, 1.19). This association was attenuated (p > 0.05) after further adjustments for other water quality factors (color grade, intestinal enterococci, and Clostridium perfringens). Our findings indicate a higher risk of fracture when consuming water of an acidic pH; however, the risk does not only seem to be due to the acidity level per se, but also to other aspects of water quality associated with pH.

Investigating aquifer contamination and groundwater quality in eastern Terai region of Nepal.

PubMed

Mahato, Sanjay; Mahato, Asmita; Karna, Pankaj Kumar; Balmiki, Nisha

2018-05-21

This study aims at assessing the groundwater quality of the three districts of Eastern Terai region of Nepal viz. Morang, Jhapa, Sunsari using physicochemical characteristics and statistical approach so that possible contamination of water reservoir can be understood. pH, temperature, conductivity, turbidity, color, total dissolved solids, fluorides, ammonia, nitrates, chloride, total hardness, calcium hardness, calcium, magnesium, total alkalinity, iron, manganese, arsenic have to be analyzed to know the present status of groundwater quality. Results revealed that the value of analyzed parameters were within the acceptable limits for drinking water recommended by World Health Organization except for pH, turbidity, ammonia and iron. As per Nepal Drinking Water Quality Standards, fluoride and manganese too were not complying with the permissible limit. Electrical conductivity, total dissolved solids, chloride, total hardness, calcium hardness, manganese, and total alkalinity show good positive correlation with major water quality parameters. Calcium, magnesium, total hardness, calcium hardness and total alkalinity greatly influences total dissolved solids and electrical conductivity. ANOVA, Tukey, and clustering highlight the significance of three districts. Groundwater can be considered safe, but there is always a chance of contamination through chemical wastes in the heavily industrialized area of Morang and Sunsari Industrial corridor.

Fabrication of a Miniature Multi-Parameter Sensor Chip for Water Quality Assessment.

PubMed

Zhou, Bo; Bian, Chao; Tong, Jianhua; Xia, Shanhong

2017-01-14

Water contamination is a main inducement of human diseases. It is an important step to monitor the water quality in the water distribution system. Due to the features of large size, high cost, and complicated structure of traditional water determination sensors and devices, it is difficult to realize real-time water monitoring on a large scale. In this paper, we present a multi-parameter sensor chip, which is miniature, low-cost, and robust, to detect the pH, conductivity, and temperature of water simultaneously. The sensor chip was fabricated using micro-electro-mechanical system (MEMS) techniques. Iridium oxide film was electrodeposited as the pH-sensing material. The atomic ratio of Ir(III) to Ir(IV) is about 1.38 according to the X-ray photoelectron spectroscopy (XPS) analysis. The pH sensing electrode showed super-Nernstian response (-67.60 mV/pH) and good linearity (R² = 0.9997), in the range of pH 2.22 to pH 11.81. KCl-agar and epoxy were used as the electrolyte layer and liquid junction for the solid-state reference electrode, respectively, and its potential stability in deionized water was 56 h. The conductivity cell exhibited a linear determination range from 21.43 μ S / cm to 1.99 mS / cm , and the electrode constant was 1.566 cm -1 . Sensitivity of the temperature sensor was 5.46 Ω / ° C . The results indicate that the developed sensor chip has potential application in water quality measurements.

Distribution of water quality parameters in Dhemaji district, Assam (India).

PubMed

Buragohain, Mridul; Bhuyan, Bhabajit; Sarma, H P

2010-07-01

The primary objective of this study is to present a statistically significant water quality database of Dhemaji district, Assam (India) with special reference to pH, fluoride, nitrate, arsenic, iron, sodium and potassium. 25 water samples collected from different locations of five development blocks in Dhemaji district have been studied separately. The implications presented are based on statistical analyses of the raw data. Normal distribution statistics and reliability analysis (correlation and covariance matrix) have been employed to find out the distribution pattern, localisation of data, and other related information. Statistical observations show that all the parameters under investigation exhibit non uniform distribution with a long asymmetric tail either on the right or left side of the median. The width of the third quartile was consistently found to be more than the second quartile for each parameter. Differences among mean, mode and median, significant skewness and kurtosis value indicate that the distribution of various water quality parameters in the study area is widely off normal. Thus, the intrinsic water quality is not encouraging due to unsymmetrical distribution of various water quality parameters in the study area.

Effects of the Deslagging Process on some Physicochemical Parameters of Honey

PubMed Central

Ranjbar, Ali Mohammad; Sadeghpour, Omid; Khanavi, Mahnaz; Shams Ardekani, Mohammad Reza; Moloudian, Hamid; Hajimahmoodi, Mannan

2015-01-01

Some physicochemical parameters of honey have been introduced by the International Honey Commission to evaluate its quality and origin but processes such as heating and filtering can affect these parameters. In traditional Iranian medicine, deslagging process involves boiling honey in an equal volume of water and removing the slag formed during process. The aim of this study was to determine the effects of deslagging process on parameters of color intensity, diastase evaluation, electrical conductivity, pH, free acidity, refractive index, hydroxy methyl furfural (HMF), proline and water contents according to the International Honey Committee (IHC) standards. The results showed that deslagged honey was significantly different from control honey in terms of color intensity, pH, diastase number, HMF and proline content. It can be concluded that the new standards are needed to regulate deslagged honey. PMID:25901175

Impact of freezing and thawing on the quality of meat: review.

PubMed

Leygonie, Coleen; Britz, Trevor J; Hoffman, Louwrens C

2012-06-01

This comprehensive review describes the effects of freezing and thawing on the physical quality parameters of meat. The formation of ice crystals during freezing damages the ultrastructure and concentrates the solutes in the meat which, in turn, leads to alterations in the biochemical reactions that occur at the cellular level and influence the physical quality parameters of the meat. The quality parameters that were evaluated are moisture loss, protein denaturation, lipid and protein oxidation, colour, pH, shear force and microbial spoilage. Additionally mechanisms employed to mitigate the effects of freezing and thawing were also reviewed. These include the use of novel methods of freezing and thawing, ante and post mortem antifreeze protein inclusion and vitamin E supplementation, brine injection and modified atmospheric packaging. Copyright © 2012 Elsevier Ltd. All rights reserved.

Quality assessment and artificial neural networks modeling for characterization of chemical and physical parameters of potable water.

PubMed

Salari, Marjan; Salami Shahid, Esmaeel; Afzali, Seied Hosein; Ehteshami, Majid; Conti, Gea Oliveri; Derakhshan, Zahra; Sheibani, Solmaz Nikbakht

2018-04-22

Today, due to the increase in the population, the growth of industry and the variety of chemical compounds, the quality of drinking water has decreased. Five important river water quality properties such as: dissolved oxygen (DO), total dissolved solids (TDS), total hardness (TH), alkalinity (ALK) and turbidity (TU) were estimated by parameters such as: electric conductivity (EC), temperature (T), and pH that could be measured easily with almost no costs. Simulate water quality parameters were examined with two methods of modeling include mathematical and Artificial Neural Networks (ANN). Mathematical methods are based on polynomial fitting with least square method and ANN modeling algorithms are feed-forward networks. All conditions/circumstances covered by neural network modeling were tested for all parameters in this study, except for Alkalinity. All optimum ANN models developed to simulate water quality parameters had precision value as R-value close to 0.99. The ANN model extended to simulate alkalinity with R-value equals to 0.82. Moreover, Surface fitting techniques were used to refine data sets. Presented models and equations are reliable/useable tools for studying water quality parameters at similar rivers, as a proper replacement for traditional water quality measuring equipment's. Copyright © 2018 Elsevier Ltd. All rights reserved.

Development of a laboratory prototype water quality monitoring system suitable for use in zero gravity

NASA Technical Reports Server (NTRS)

Misselhorn, J. E.; Witz, S.; Hartung, W. H.

1973-01-01

The development of a laboratory prototype water quality monitoring system for use in the evaluation of candidate water recovery systems and for study of techniques for measuring potability parameters is reported. Sensing techniques for monitoring of the most desirable parameters are reviewed in terms of their sensitivities and complexities, and their recommendations for sensing techniques are presented. Rationale for selection of those parameters to be monitored (pH, specific conductivity, Cr(+6), I2, total carbon, and bacteria) in a next generation water monitor is presented along with an estimate of flight system specifications. A master water monitor development schedule is included.

Quantitative Determination of Spring Water Quality Parameters via Electronic Tongue

PubMed Central

Carbó, Noèlia; López Carrero, Javier; Garcia-Castillo, F. Javier; Olivas, Estela; Folch, Elisa; Alcañiz Fillol, Miguel; Soto, Juan

2017-01-01

The use of a voltammetric electronic tongue for the quantitative analysis of quality parameters in spring water is proposed here. The electronic voltammetric tongue consisted of a set of four noble electrodes (iridium, rhodium, platinum, and gold) housed inside a stainless steel cylinder. These noble metals have a high durability and are not demanding for maintenance, features required for the development of future automated equipment. A pulse voltammetry study was conducted in 83 spring water samples to determine concentrations of nitrate (range: 6.9–115 mg/L), sulfate (32–472 mg/L), fluoride (0.08–0.26 mg/L), chloride (17–190 mg/L), and sodium (11–94 mg/L) as well as pH (7.3–7.8). These parameters were also determined by routine analytical methods in spring water samples. A partial least squares (PLS) analysis was run to obtain a model to predict these parameter. Orthogonal signal correction (OSC) was applied in the preprocessing step. Calibration (67%) and validation (33%) sets were selected randomly. The electronic tongue showed good predictive power to determine the concentrations of nitrate, sulfate, chloride, and sodium as well as pH and displayed a lower R2 and slope in the validation set for fluoride. Nitrate and fluoride concentrations were estimated with errors lower than 15%, whereas chloride, sulfate, and sodium concentrations as well as pH were estimated with errors below 10%. PMID:29295592

Impact of Yangtze River Water Transfer on the Water Quality of the Lixia River Watershed, China

PubMed Central

Ma, Xiaoxue; Wang, Lachun; Wu, Hao; Li, Na; Ma, Lei; Zeng, Chunfen; Zhou, Yi; Yang, Jun

2015-01-01

To improve water quality and reduce the negative impacts of sudden inputs of water pollution in the Lixia River watershed, China, a series of experimental water transfers from the Yangtze River to the Lixia River were conducted from 2 December 2006 to 7 January 2007. Water samples were collected every six days at 55 monitoring sites during this period. Eight water parameters (water temperature, pH, dissolved oxygen (DO), chemical oxygen demand (COD), potassium permanganate index (CODMn), ammonia nitrogen (NH4 +-N), electrical conductivity (EC), and water transparency (WT)) were analyzed to determine changes in nutrient concentrations during water transfers. The comprehensive pollution index (Pi) and single-factor (Si) evaluation methods were applied to evaluate spatio-temporal patterns of water quality during water transfers. Water quality parameters displayed different spatial and temporal distribution patterns within the watershed. Water quality was improved significantly by the water transfers, especially for sites closer to water intake points. The degree of improvement is positively related to rates of transfer inflow and drainage outflow. The effects differed for different water quality parameters at each site and at different water transfer times. There were notable decreases in NH4 +-N, DO, COD, and CODMn across the entire watershed. However, positive effects on EC and pH were not observed. It is concluded that freshwater transfers from the Yangtze River can be used as an emergency measure to flush pollutants from the Lixia River watershed. Improved understanding of the effects of water transfers on water quality can help the development and implementation of effective strategies to improve water quality within this watershed. PMID:25835525

Chicken meat quality: genetic variability and relationship with growth and muscle characteristics

PubMed Central

Le Bihan-Duval, Elisabeth; Debut, Martine; Berri, Cécile M; Sellier, Nadine; Santé-Lhoutellier, Véronique; Jégo, Yves; Beaumont, Catherine

2008-01-01

Background The qualitative properties of the meat are of major importance for poultry breeding, since meat is now widely consumed as cuts or as processed products. The aim of this study was to evaluate the genetic parameters of several breast meat quality traits and their genetic relationships with muscle characteristics in a heavy commercial line of broilers. Results Significant levels of heritability (averaging 0.3) were obtained for breast meat quality traits such as pH at 15 min post-slaughter, ultimate pH (pHu), color assessed by lightness L*, redness a* and yellowness b*, drip loss, thawing-cooking loss and shear-force. The rate of decrease in pH early post-mortem and the final pH of the meat were shown to be key factors of chicken meat quality. In particular, a decrease in the final pH led to paler, more exudative and tougher breast meat. The level of glycogen stored in breast muscle estimated by the Glycolytic Potential (GP) at slaughter time was shown to be highly heritable (h2 0.43). There was a very strong negative genetic correlation (rg) with ultimate meat pH (rg -0.97), suggesting a common genetic control for GP and pHu. While breast muscle weight was genetically positively correlated with fiber size (rg 0.76), it was negatively correlated with the level of glycogen stored in the muscle (rg -0.58), and as a consequence it was positively correlated with the final pH of the meat (rg 0.84). Conclusion This genetic study confirmed that selection should be useful to improve meat characteristics of meat-type chickens without impairing profitability because no genetic conflict was detected between meat quality and meat quantity. Moreover, the results suggested relevant selection criteria such as ultimate pH, which is strongly related to color, water-holding capacity and texture of the meat in this heavy chicken line. PMID:18706119

Quality Parameters of Six Cultivars of Blueberry Using Computer Vision

PubMed Central

Celis Cofré, Daniela; Silva, Patricia; Enrione, Javier; Osorio, Fernando

2013-01-01

Background. Blueberries are considered an important source of health benefits. This work studied six blueberry cultivars: “Duke,” “Brigitta”, “Elliott”, “Centurion”, “Star,” and “Jewel”, measuring quality parameters such as °Brix, pH, moisture content using standard techniques and shape, color, and fungal presence obtained by computer vision. The storage conditions were time (0–21 days), temperature (4 and 15°C), and relative humidity (75 and 90%). Results. Significant differences (P < 0.05) were detected between fresh cultivars in pH, °Brix, shape, and color. However, the main parameters which changed depending on storage conditions, increasing at higher temperature, were color (from blue to red) and fungal presence (from 0 to 15%), both detected using computer vision, which is important to determine a shelf life of 14 days for all cultivars. Similar behavior during storage was obtained for all cultivars. Conclusion. Computer vision proved to be a reliable and simple method to objectively determine blueberry decay during storage that can be used as an alternative approach to currently used subjective measurements. PMID:26904598

Fabrication of a Miniature Multi-Parameter Sensor Chip for Water Quality Assessment

PubMed Central

Zhou, Bo; Bian, Chao; Tong, Jianhua; Xia, Shanhong

2017-01-01

Water contamination is a main inducement of human diseases. It is an important step to monitor the water quality in the water distribution system. Due to the features of large size, high cost, and complicated structure of traditional water determination sensors and devices, it is difficult to realize real-time water monitoring on a large scale. In this paper, we present a multi-parameter sensor chip, which is miniature, low-cost, and robust, to detect the pH, conductivity, and temperature of water simultaneously. The sensor chip was fabricated using micro-electro-mechanical system (MEMS) techniques. Iridium oxide film was electrodeposited as the pH-sensing material. The atomic ratio of Ir(III) to Ir(IV) is about 1.38 according to the X-ray photoelectron spectroscopy (XPS) analysis. The pH sensing electrode showed super-Nernstian response (−67.60 mV/pH) and good linearity (R2 = 0.9997), in the range of pH 2.22 to pH 11.81. KCl-agar and epoxy were used as the electrolyte layer and liquid junction for the solid-state reference electrode, respectively, and its potential stability in deionized water was 56 h. The conductivity cell exhibited a linear determination range from 21.43 μS/cm to 1.99 mS/cm, and the electrode constant was 1.566 cm−1. Sensitivity of the temperature sensor was 5.46 Ω/°C. The results indicate that the developed sensor chip has potential application in water quality measurements. PMID:28098824

Empirical algorithms to estimate water column pH in the Southern Ocean

NASA Astrophysics Data System (ADS)

Williams, N. L.; Juranek, L. W.; Johnson, K. S.; Feely, R. A.; Riser, S. C.; Talley, L. D.; Russell, J. L.; Sarmiento, J. L.; Wanninkhof, R.

2016-04-01

Empirical algorithms are developed using high-quality GO-SHIP hydrographic measurements of commonly measured parameters (temperature, salinity, pressure, nitrate, and oxygen) that estimate pH in the Pacific sector of the Southern Ocean. The coefficients of determination, R2, are 0.98 for pH from nitrate (pHN) and 0.97 for pH from oxygen (pHOx) with RMS errors of 0.010 and 0.008, respectively. These algorithms are applied to Southern Ocean Carbon and Climate Observations and Modeling (SOCCOM) biogeochemical profiling floats, which include novel sensors (pH, nitrate, oxygen, fluorescence, and backscatter). These algorithms are used to estimate pH on floats with no pH sensors and to validate and adjust pH sensor data from floats with pH sensors. The adjusted float data provide, for the first time, seasonal cycles in surface pH on weekly resolution that range from 0.05 to 0.08 on weekly resolution for the Pacific sector of the Southern Ocean.

[Successful esophageal pH monitoring with Bravo capsule in patients with gastroesophageal reflux disease].

PubMed

Valdovinos Díaz, Miguel A; Remes Troche, José Ma; Ruiz Aguilar, Juan Carlos; Schmulson, Max J; Valdovinos-Andraca, Francisco

2004-01-01

Esophageal 24-h pH monitoring (24-pH) is the most useful test to diagnose and treat patients with gastroesophageal reflux disease (GERD). The traditional system for 24-pH requires transnasal introduction of a catheter with pH sensors. This technique produces discomfort, inconvenience and interference with daily activity. Recently, the Bravo pH system has been proposed as an alternative and promising method for 24-pH. In this study, the initial experience in Mexico with this system is reported. To evaluate safety, tolerability and performance of the pH Bravo capsule in patients with GERD. Patients with GERD symptoms at least twice a week during the last three months, with indication for 24-pH were evaluated. pH Bravo capsule was placed 6 cm above squamocolumnar junction (SCJ). Symptoms, quality and duration of pH tracings, capsule detachment and patient global satisfaction were evaluated. Eleven patients (nine female, two male) mean age 42 years (range 26-62 years), two with erosive and nine with non-erosive GERD were studied. pH capsule was correctly positioned at 6 cm above SCJ in all patients. Nine patients noted a mild foreign body sensation (especially while eating) and four had mild chest pain; two patients had no discomfort. Capsule detachment occurred spontaneously in all patients on day 10. pH record for > 43 h was obtained in the 11 patients. There were no differences in pH parameters between days 1 and 2. Two patients with normal acid exposure on day 1 had abnormal pH parameters on day 2. Esophageal pH monitoring with Bravo capsule is a safe, reliable and tolerable method in patients with GERD. Extended pH recordings increases abnormal esophageal acid exposure detection in patients with this disease.

Water quality of Tampa Bay, Florida, June 1972-May 1976

USGS Publications Warehouse

Goetz, Carole L.; Goodwin, Carl R.

1980-01-01

A comprehensive assessment of the water quality of Tampa Bay, Florida, was initiated in 1970 to provide background information to evaluate the effects of widening and deepening the ship channel to the port of Tampa. This report provides results of water-quality sampling in the bay from 1972 to 1976, prior to dredging. Measurements of temperature, dissolved oxygen, pH, turbidity, specific conductance, biochemical oxygen demand, and total organic carbon were made as well as measurements for several nutrient, metal, and pesticide parameters. Many parameters were measured at as many as three points in the vertical. These data indicate that Tampa Bay is well-mixed vertically with little density stratification. Time histories of average temperature, dissolved oxygen, pH, turbidity, specific conductance and nutrient values within four subareas of Tampa Bay are given to reveal seasonal or other trends during the period of record. Temperature, dissolved oxygen, pH, turbidity, specific conductance, nutrient, biochemical oxygen demand, total organic carbon, and metal data are also presented as areal distributions. Nutrient concentrations were generally higher in Hillsborough Bay than in other sub-areas of Tampa Bay. Biochemical oxygen demand, total organic carbon, and total organic nitrogen distribution patterns show regions of highest concentrations to be along bay shorelines near population centers. Of the metals analyzed, all were present in concentrations of less than 1 milligram per liter. (USGS)

Use of Multiple Linear Regression Models for Setting Water Quality Criteria for Copper: A Complementary Approach to the Biotic Ligand Model.

PubMed

Brix, Kevin V; DeForest, David K; Tear, Lucinda; Grosell, Martin; Adams, William J

2017-05-02

Biotic Ligand Models (BLMs) for metals are widely applied in ecological risk assessments and in the development of regulatory water quality guidelines in Europe, and in 2007 the United States Environmental Protection Agency (USEPA) recommended BLM-based water quality criteria (WQC) for Cu in freshwater. However, to-date, few states have adopted BLM-based Cu criteria into their water quality standards on a state-wide basis, which appears to be due to the perception that the BLM is too complicated or requires too many input variables. Using the mechanistic BLM framework to first identify key water chemistry parameters that influence Cu bioavailability, namely dissolved organic carbon (DOC), pH, and hardness, we developed Cu criteria using the same basic methodology used by the USEPA to derive hardness-based criteria but with the addition of DOC and pH. As an initial proof of concept, we developed stepwise multiple linear regression (MLR) models for species that have been tested over wide ranges of DOC, pH, and hardness conditions. These models predicted acute Cu toxicity values that were within a factor of ±2 in 77% to 97% of tests (5 species had adequate data) and chronic Cu toxicity values that were within a factor of ±2 in 92% of tests (1 species had adequate data). This level of accuracy is comparable to the BLM. Following USEPA guidelines for WQC development, the species data were then combined to develop a linear model with pooled slopes for each independent parameter (i.e., DOC, pH, and hardness) and species-specific intercepts using Analysis of Covariance. The pooled MLR and BLM models predicted species-specific toxicity with similar precision; adjusted R 2 and R 2 values ranged from 0.56 to 0.86 and 0.66-0.85, respectively. Graphical exploration of relationships between predicted and observed toxicity, residuals and observed toxicity, and residuals and concentrations of key input parameters revealed many similarities and a few key distinctions between the performances of the two models. The pooled MLR model was then applied to the species sensitivity distribution to derive acute and chronic criteria equations similar in form to the USEPA's current hardness-based criteria equations but with DOC, pH, and hardness as the independent variables. Overall, the MLR is less responsive to DOC than the BLM across a range of hardness and pH conditions but more responsive to hardness than the BLM. Additionally, at low and intermediate hardness, the MLR model is less responsive than the BLM to pH, but the two models respond comparably at high hardness. The net effect of these different response profiles is that under many typical water quality conditions, MLR- and BLM-based criteria are quite comparable. Indeed, conditions where the two models differ most (high pH/low hardness and low pH/high hardness) are relatively rare in natural aquatic systems. We suggest that this MLR-based approach, which includes the mechanistic foundation of the BLM but is also consistent with widely accepted hardness-dependent WQC in terms of development and form, may facilitate adoption of updated state-wide Cu criteria that more accurately account for the parameters influencing Cu bioavailability than current hardness-based criteria.

The determination of water quality and metal concentrations of Ampang Hilir Lake, Selangor, Peninsular Malaysia.

PubMed

Said, Khaled S A; Shuhaimi-Othman, M; Ahmad, A K

2012-05-01

A study of water quality parameters (temperature, conductivity, total dissolved solid, dissolved oxygen, pH and water hardness) in Ampang Hilir Lake was conducted in January, April, July and October 2010. The water quality parameters were tested and recorded at different sampling stations chosen randomly using Hydrolab Data Sonde 4 and Surveyor 4 a water quality multi probe (USA). Six metals which were cadmium, chromium, lead, nickel, zinc and copper were determined in five different compartments of the lake namely water, total suspended solids, plankton, sediment and fish. The metals concentration were determined by Inductively Coupled Plasma Mass Spectrometer (ICP-MS), Perkin Elmer Elan, model 9000.The water quality parameters were compared with National Water Quality Standard (NWQS Malaysia) while metal concentrations were compared with Malaysian and international standards. The study shows that water quality parameters are of class 2. This condition is suitable for recreational activities where body contact is allowed and suitable for sensitive fishing activities. Furthermore, metal concentrations were found to be lower than the international standards, therefore toxic effects for these metals would be rarely observed and the adverse effects to aquatic organisms would not frequently occur.

Nondestructive detection of pork quality based on dual-band VIS/NIR spectroscopy

NASA Astrophysics Data System (ADS)

Wang, Wenxiu; Peng, Yankun; Li, Yongyu; Tang, Xiuying; Liu, Yuanyuan

2015-05-01

With the continuous development of living standards and the relative change of dietary structure, consumers' rising and persistent demand for better quality of meat is emphasized. Colour, pH value, and cooking loss are important quality attributes when evaluating meat. To realize nondestructive detection of multi-parameter of meat quality simultaneously is popular in production and processing of meat and meat products. The objectives of this research were to compare the effectiveness of two bands for rapid nondestructive and simultaneous detection of pork quality attributes. Reflectance spectra of 60 chilled pork samples were collected from a dual-band visible/near-infrared spectroscopy system which covered 350-1100 nm and 1000-2600 nm. Then colour, pH value and cooking loss were determined by standard methods as reference values. Standard normal variables transform (SNVT) was employed to eliminate the spectral noise. A spectrum connection method was put forward for effective integration of the dual-band spectrum to make full use of the whole efficient information. Partial least squares regression (PLSR) and Principal component analysis (PCA) were applied to establish prediction models using based on single-band spectrum and dual-band spectrum, respectively. The experimental results showed that the PLSR model based on dual-band spectral information was superior to the models based on single band spectral information with lower root means quare error (RMSE) and higher accuracy. The PLSR model based on dual-band (use the overlapping part of first band) yielded the best prediction result with correlation coefficient of validation (Rv) of 0.9469, 0.9495, 0.9180, 0.9054 and 0.8789 for L*, a*, b*, pH value and cooking loss, respectively. This mainly because dual-band spectrum can provide sufficient and comprehensive information which reflected the quality attributes. Data fusion from dual-band spectrum could significantly improve pork quality parameters prediction performance. The research also indicated that multi-band spectral information fusion has potential to comprehensively evaluate other quality and safety attributes of pork.

Monitoring the startup of a wet detention pond equipped with sand filters and sorption filters.

PubMed

Vollertsen, J; Lange, K H; Pedersen, J; Hallager, P; Bruus, A; Laustsen, A; Bundesen, V W; Brix, H; Nielsen, A H; Nielsen, N H; Wium-Andersen, T; Hvitved-Jacobsen, T

2009-01-01

The startup of a wet retention pond designed for extended stormwater treatment was monitored by more than one year of continual measurement of hydraulic parameters, nutrients and quality parameters in the pond itself (pH, temperature, dissolved oxygen, turbidity). The data revealed that photosynthesis played an important role for dissolved oxygen and pH for most of the year. Another important observation was that the pond behaved more like a completely mixed reactor than like a plug flow reactor--even though the length to width ratio was as high as 4.5:1. The pond was equipped with sand filters and sorption filters whereby very good nutrient removal efficiencies were achieved.

Multivariate analysis of drinking water quality parameters in Bhopal, India.

PubMed

Parashar, Charu; Verma, Neelam; Dixit, Savita; Shrivastava, Rajneesh

2008-05-01

Pollution of water bodies is one of the areas of major concern to environmentalists. Water quality is an index of health and well being of a society. Industrialization, urbanization and modern agriculture practices have direct impact on the water resources. These factors influence the water resources quantitatively and qualitatively. The study area selected were the Upper lake and Kolar reservoir of Bhopal, the state capital of Madhya Pradesh, India. The Upper lake and Kolar reservoir both are the important sources of potable water supply for the Bhopal city. The physico-chemical parameters like temperature, pH, turbidity, total hardness, alkalinity, BOD, COD, Chloride, nitrate and phosphate were studied to ascertain the drinking water quality.

Item response theory analysis of Centers for Disease Control and Prevention Health-Related Quality of Life (CDC HRQOL) items in adults with arthritis.

PubMed

Mielenz, Thelma J; Callahan, Leigh F; Edwards, Michael C

2016-03-12

Examine the feasibility of performing an item response theory (IRT) analysis on two of the Centers for Disease Control and Prevention health-related quality of life (CDC HRQOL) modules - the 4-item Healthy Days Core Module (HDCM) and the 5-item Healthy days Symptoms Module (HDSM). Previous principal components analyses confirm that the two scales both assess a mix of mental (CDC-MH) and physical health (CDC-PH). The purpose is to conduct item response theory (IRT) analysis on the CDC-MH and CDC-PH scales separately. 2182 patients with self-reported or physician-diagnosed arthritis completed a cross-sectional survey including HDCM and HDSM items. Besides global health, the other 8 items ask the number of days that some statement was true; we chose to recode the data into 8 categories based on observed clustering. The IRT assumptions were assessed using confirmatory factor analysis and the data could be modeled using an unidimensional IRT model. The graded response model was used for IRT analyses and CDC-MH and CDC-PH scales were analyzed separately in flexMIRT. The IRT parameter estimates for the five-item CDC-PH all appeared reasonable. The three-item CDC-MH did not have reasonable parameter estimates. The CDC-PH scale is amenable to IRT analysis but the existing The CDC-MH scale is not. We suggest either using the 4-item Healthy Days Core Module (HDCM) and the 5-item Healthy days Symptoms Module (HDSM) as they currently stand or the CDC-PH scale alone if the primary goal is to measure physical health related HRQOL.

Biphasic cultivation strategy to avoid Epo-Fc aggregation and optimize protein expression.

PubMed

Kaisermayer, Christian; Reinhart, David; Gili, Andreas; Chang, Martina; Aberg, Per-Mikael; Castan, Andreas; Kunert, Renate

2016-06-10

In biphasic cultivations, the culture conditions are initially kept at an optimum for rapid cell growth and biomass accumulation. In the second phase, the culture is shifted to conditions ensuring maximum specific protein production and the protein quality required. The influence of specific culture parameters is cell line dependent and their impact on product quality needs to be investigated. In this study, a biphasic cultivation strategy for a Chinese hamster ovary (CHO) cell line expressing an erythropoietin fusion protein (Epo-Fc) was developed. Cultures were run in batch mode and after an initial growth phase, cultivation temperature and pH were shifted. Applying a DoE (Design of Experiments) approach, a fractional factorial design was used to systematically evaluate the influence of cultivation temperature and pH as well as their synergistic effect on cell growth as well as on recombinant protein production and aggregation. All three responses were influenced by the cultivation temperature. Additionally, an interaction between pH and temperature was found to be related to protein aggregation. Compared with the initial standard conditions of 37°C and pH 7.05, a parameter shift to low temperature and acidic pH resulted in a decrease in the aggregate fraction from 75% to less than 1%. Furthermore, the synergistic effect of temperature and pH substantially lowered the cell-specific rates of glucose and glutamine consumption as well as lactate and ammonium production. The optimized culture conditions also led to an increase of the cell-specific rates of recombinant Epo-Fc production, thus resulting in a more economic bioprocess. Copyright © 2016. Published by Elsevier B.V.

Quality comparison of elephant apple juices after high-pressure processing and thermal treatment.

PubMed

Nayak, Prakash Kumar; Rayaguru, Kalpana; Radha Krishnan, Kesavan

2017-03-01

In the present work, the effect of high pressure processing (HPP) on the quality parameters (pH, °Brix, total acidity, viscosity, colour, antioxidant activity, total phenols, total flavonoids, microbial flora, and sensory analysis) of elephant apple (Dillenia indica) juice was investigated. The juice samples were analysed periodically (0, 1, 2, 5, 10, 20, 30, 40, 50 and 60 days) during 60 days of storage period and results were compared with thermally processed as well as with untreated (fresh juice) samples. Slight variations had been observed in the quality parameters like pH, °Brix and total acidity. Other parameters like colour values, antioxidant activity, total phenols and total flavonoids were varied significantly (P < 0.05) in between the treated (HPP and thermal) and untreated juice samples. The microbial counts of the HPP treated samples were lower than the other samples. Sensory results also showed similar results to those of the other analyses that the treated samples were better for consumption rather than the untreated samples. The shelf-life of the HPP processed elephant apple juice was established as 60 days at 4 °C. This study showed that application of HPP effectively maintained quality attributes and extended shelf life of the elephant apple juice. It may be suggested that application of HPP could be considered for commercial application during storage and marketing. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Non-Linear Metamodeling Extensions to the Robust Parameter Design of Computer Simulations

DTIC Science & Technology

2016-09-15

design By principal component analysis," Total Quality Management, vol. 8, no. 6, pp. 409-416, 1997. [25] A. Salmasnia, R. B . Kazemzadeh and S. T . A...and D. T . Sturrock, Simulation with Arena (3rd ed.), New York, NY: McGraw-Hill, 2004. [85] A. M. Mathai and S. B . Provost, Quadratic Forms in Random...PhD Member ADEDEJI B . BADIRU, PhD Dean, Graduate School of Engineering and Management iv AFIT-ENS-DS-16-S-026 Abstract Robust

Assessment of physico-chemical characteristics of water in Tamilnadu.

PubMed

Udhayakumar, R; Manivannan, P; Raghu, K; Vaideki, S

2016-12-01

Water is an important component to human life. The major aims of the present work are to assess the quality of the ground water and its impact in Villupuram District of Tamilnadu. The present study focus to bring an awareness among the people about the quality of ground water by taking water samples from various locations for Physico - Chemical analysis of the ground water. This analysis result was compared with the WHO, ICMR, USPH and European standards of drinking water quality parameters with the following water quality parameters namely pH, Electrical conductivity, Cl, , Na, K, Ca , Mg, Total dissolved solids, Total hardness, Dissolved oxygen, Fluoride etc. Various chemical methods have been employed to investigate the extent level of pollution in ground water. Copyright © 2016 Elsevier Inc. All rights reserved.

Stagnant surface water bodies (SSWBs) as an alternative water resource for the Chittagong metropolitan area of Bangladesh: physicochemical characterization in terms of water quality indices.

PubMed

Rahman, Ismail Md Mofizur; Islam, M Monirul; Hossain, M Mosharraf; Hossain, M Shahadat; Begum, Zinnat A; Chowdhury, Didarul A; Chakraborty, Milan K; Rahman, M Azizur; Nazimuddin, M; Hasegawa, Hiroshi

2011-02-01

The concern over ensuing freshwater scarcity has forced the developing countries to delve for alternative water resources. In this study, we examined the potential of stagnant surface water bodies (SSWBs) as alternative freshwater resources in the densely populated Chittagong metropolitan area (CMPA) of Bangladesh--where there is an acute shortage of urban freshwater supply. Water samples were collected at 1-month intervals for a period of 1 year from 12 stations distributed over the whole metropolis. Samples were analyzed for pH, water temperature (WTemp), turbidity, electrical conductivity (EC), total dissolved solids, total solids, total hardness, dissolved oxygen (DO), chloride, orthophosphates, ammonia, total coliforms (TC), and trace metal (Cd, Cr, Cu, Pb, As, and Fe) concentrations. Based on these parameters, different types of water quality indices (WQIs) were deduced. WQIs showed most of CMPA-SSWBs as good or medium quality water bodies, while none were categorized as bad. Moreover, it was observed that the minimal water quality index (WQIm), computed using five parameters: WTemp, pH, DO, EC, and turbidity, gave a reliable estimate of water quality. The WQIm gave similar results in 72% of the cases compared with other WQIs that were based on larger set of parameters. Based on our finding, we suggest the wider use WQIm in developing countries for assessing health of SSWBs, as it will minimize the analytical cost to overcome the budget constraints involved in this kind of evaluations. It was observed that except turbidity and TC content, all other quality parameters fluctuated within the limit of the World Health Organization suggested standards for drinking water. From our findings, we concluded that if the turbidity and TC content of water from SSWBs in CMPA are taken care of, they will become good candidates as alternative water resources all round the year.

Characterization of alkaline phosphatase activity in seminal plasma and in fresh and frozen-thawed stallion spermatozoa.

PubMed

Bucci, Diego; Giaretta, Elisa; Spinaci, Marcella; Rizzato, Giovanni; Isani, Gloria; Mislei, Beatrice; Mari, Gaetano; Tamanini, Carlo; Galeati, Giovanna

2016-01-15

Alkaline phosphatase (AP) has been studied in several situations to elucidate its role in reproductive biology of the male from different mammalian species; at present, its role in horse sperm physiology is not clear. The aim of the present work was to measure AP activity in seminal plasma and sperm extracts from freshly ejaculated as well as in frozen-thawed stallion spermatozoa and to verify whether relationship exists between AP activity and sperm quality parameters. Our data on 40 freshly ejaculated samples from 10 different stallions demonstrate that the main source of AP activity is seminal plasma, whereas sperm extracts contribution is very low. In addition, we found that AP activity at physiological pH (7.0) is significantly lower than that observed at pH 8.0, including the optimal AP pH (pH 10.0). Alkaline phosphatase did not exert any effect on sperm-oocyte interaction assessed by heterologous oocyte binding assay. Additionally, we observed a thermal stability of seminal plasma AP, concluding that it is similar to that of bone isoforms. Positive correlations were found between seminal plasma AP activity and sperm concentration, whereas a negative correlation was present between both spermatozoa extracts and seminal plasma AP activity and seminal plasma protein content. A significant decrease in sperm extract AP activity was found in frozen-thawed samples compared with freshly ejaculated ones (n = 21), concomitantly with the decrease in sperm quality parameters. The positive correlation between seminal plasma AP activity measured at pH 10 and viability of frozen-thawed spermatozoa suggests that seminal plasma AP activity could be used as an additional predictive parameter for stallion sperm freezability. In conclusion, we provide some insights into AP activity in both seminal plasma and sperm extracts and describe a decrease in AP after freezing and thawing. Copyright © 2016 Elsevier Inc. All rights reserved.

Groundwater quality assessment for irrigation purposes based on irrigation water quality index and its zoning with GIS in the villages of Chabahar, Sistan and Baluchistan, Iran.

PubMed

Abbasnia, Abbas; Radfard, Majid; Mahvi, Amir Hossein; Nabizadeh, Ramin; Yousefi, Mahmood; Soleimani, Hamed; Alimohammadi, Mahmood

2018-08-01

The present study was conducted to evaluate the groundwater quality and its suitability for irrigation purpose through GIS in villages of Chabahr city, Sistan and Baluchistan province in Iran. This cross-sectional study was carried out from 2010 to 2011 the 1-year-monitoring period. The water samples were collected from 40 open dug wells in order to investigate the water quality. Chemical parameters including EC, SAR, Na + , Cl - , pH, TDS, H C O 3 - and IWQI were analyzed. In order to calculate the irrigation water quality index subsequent five water quality parameters (EC, SAR, Na + , Cl - , and H C O 3 - ) were utilized. Among the total of 40 samples were analyzed for IWQI, 40% of the samples classified as excellent water, 60% of the samples in good water category.

Microelectrode investigation of the reactions between metallic pipe materials and monochloramine

EPA Science Inventory

Water quality parameters (i.e., pH, dissolved oxygen [DO], and phosphate) are known to impact metal reactivity with disinfectants and therefore corrosion and metals release into drinking water supplies. With various water utilities switching from free chlorine to chloramines for ...

Effects of farm management practices and transport duration on stress response and meat quality traits of suckling goat kids.

PubMed

Alcalde, M J; Suárez, M D; Rodero, E; Álvarez, R; Sáez, M I; Martínez, T F

2017-09-01

Studies aimed to assess up to what extent farming and transport previous to slaughtering might affect physiology and meat quality in young goat kids are needed, with the ultimate purpose of promoting practices that minimize stress in these animals. In this regard the effects of on-farm management and transport duration on some physiological responses and meat quality parameters in goat kids were assessed. Two farms representing 'high' and 'low' welfare-friendly management practices were selected. In total, 32 suckling kids were withdrawn from each farm, transported by road for 2 or 6 h, and then slaughtered. Blood samples were collected both on-farm and in the slaughterhouse, and biochemistry, cell counts and haematocrit were determined. After slaughtering, carcass quality parameters were measured. Longissimus dorsi muscle was dissected and pH, colour parameters, water holding capacity and shear force were measured throughout 8-day ageing period. Results indicate that, regardless its duration, transport caused significant effects on some blood parameters suggesting stress in live animals, like glucose, cortisol or creatine kinase. Despite the marked stress status in animals, this condition was not decisively reflected on L. dorsi quality parameters, but some effects were observed regarding fat cover in carcasses and colour parameters. The results suggest that postmortem changes throughout ageing were more decisive in terms of meat quality than stressful management either on-farm or during transport.

Quality by design approach of a pharmaceutical gel manufacturing process, part 1: determination of the design space.

PubMed

Rosas, Juan G; Blanco, Marcel; González, Josep M; Alcalá, Manel

2011-10-01

This work was conducted in the framework of a quality by design project involving the production of a pharmaceutical gel. Preliminary work included the identification of the quality target product profiles (QTPPs) from historical values for previously manufactured batches, as well as the critical quality attributes for the process (viscosity and pH), which were used to construct a D-optimal experimental design. The experimental design comprised 13 gel batches, three of which were replicates at the domain center intended to assess the reproducibility of the target process. The viscosity and pH models established exhibited very high linearity and negligible lack of fit (LOF). Thus, R(2) was 0.996 for viscosity and 0.975 for pH, and LOF was 0.53 for the former parameter and 0.84 for the latter. The process proved reproducible at the domain center. Water content and temperature were the most influential factors for viscosity, and water content and acid neutralized fraction were the most influential factors for pH. A desirability function was used to find the best compromise to optimize the QTPPs. The body of information was used to identify and define the design space for the process. A model capable of combining the two response variables into a single one was constructed to facilitate monitoring of the process. Copyright © 2011 Wiley-Liss, Inc.

Application of visible/near-infrared reflectance spectroscopy for predicting internal and external quality in pepper.

PubMed

Toledo-Martín, Eva María; García-García, María Carmen; Font, Rafael; Moreno-Rojas, José Manuel; Gómez, Pedro; Salinas-Navarro, María; Del Río-Celestino, Mercedes

2016-07-01

The characterization of internal (°Brix, pH, malic acid, total phenolic compounds, ascorbic acid and total carotenoid content) and external (color, firmness and pericarp wall thickness) pepper quality is necessary to better understand its possible applications and increase consumer awareness of its benefits. The main aim of this work was to examine the feasibility of using visible/near-infrared reflectance spectroscopy (VIS-NIRS) to predict quality parameters in different pepper types. Commercially available spectrophotometers were evaluated for this purpose: a Polychromix Phazir spectrometer for intact raw pepper, and a scanning monochromator for freeze-dried pepper. The RPD values (ratio of the standard deviation of the reference data to the standard error of prediction) obtained from the external validation exceeded a value of 3 for chlorophyll a and total carotenoid content; values ranging between 2.5 < RPD < 3 for total phenolic compounds; between 1.5 < RPD <2.5 for °Brix, pH, color parameters a* and h* and chlorophyll b; and RPD values below 1.5 for fruit firmness, pericarp wall thickness, color parameters C*, b* and L*, vitamin C and malic acid content. The present work has led to the development of multi-type calibrations for pepper quality parameters in intact and freeze-dried peppers. The majority of NIRS equations obtained were suitable for screening purposes in pepper breeding programs. Components such as pigments (xanthophyll, carotenes and chlorophyll), glucides, lipids, cellulose and water were used by modified partial least-squares regression for modeling the predicting equations. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Water quality in the tropical Andes hotspot: The Yacuambi river (southeastern Ecuador).

PubMed

Villa-Achupallas, Mercedes; Rosado, Daniel; Aguilar, Silvio; Galindo-Riaño, María Dolores

2018-08-15

Yacuambi river waters (southeast Ecuador, Amazonian region) were assessed to evaluate the potential risk to populations, who use it for drinking and irrigation, and ecosystems, which are part of Tropical Andes hotspot and considered some of the most biodiverse in the world. The water quality index was calculated and some quality parameters were checked to comply with Ecuadorian and North American standards for human consumption, preservation of aquatic life and irrigation. Four samplings were carried out in six stations covering the entire length of the Yacuambi river. Several parameters were analyzed: pH, conductivity, dissolved oxygen, temperature, color, phosphates, nitrite, nitrate, biochemical oxygen demand, chemical oxygen demand, total solids, turbidity, metals (Ba, Cd, Cr, Pb, As and Hg), pesticides and fecal coliforms. The water quality in the Yacuambi river was good and medium according to the classification of the Water Quality Index. However, it was unsuitable for human consumption, preservation of aquatic life and irrigation according to Ecuadorian and North American standards. Arsenic, color and fecal coliforms exceeded the limits for human consumption in all samples tested. Thresholds of preservation of aquatic life were exceeded in all samples in the case of Pb and in some samples for As, pH, nitrite and nitrate. Arsenic and fecal coliforms made Yacuambi river waters unsuitable for irrigation. Copyright © 2018 Elsevier B.V. All rights reserved.

Quality characteristics of broiler chicken meat from free-range and industrial poultry system for the consumers.

PubMed

da Silva, Débora Cristina Fernandes; de Arruda, Alex Martins Varela; Gonçalves, Alex Augusto

2017-06-01

The aim of this study was to determine and compare the quality parameters of broiler chicken meat from free-range and industrial poultry system. Proximate composition, color, pH, shear force, microbial quality and sensory characteristics were evaluated. Both free-range and industrial chicken meat presented PSE (pale, soft and exudative) anomaly ( L * > 53). An inverse correlation between lightness, pH and shear force was observed. The free range broiler meat had higher yellow color ( b * 11.56) and shear force (2.75 kgf) and lower red color ( a * 1.65) and pH (5.75) in comparison to the industrial broiler meat, due intensive physical activity on growing phase and influence of the pre-slaughter stress on the rigor mortis. The thigh cut from free range broiler meat showed higher protein levels (18.00%), while to the thigh and drumstick cuts of industrial broiler meat showed higher total fat levels (3.4 and 5.0%, respectively). In general, each strain and chickens producing methods gave the peculiar characteristics to meat (chemical, physical, microbiological and sensorial).

Development of Fast Response In-situ Sensors for Simultaneous Measurements of Seawater Carbon Dioxide Parameters

NASA Astrophysics Data System (ADS)

Wang, A. Z.; Sonnichsen, F. N.; Chu, S. N.; Bradley, A. M.; Hoering, K.

2016-02-01

The marine CO2 (inorganic carbon) system is characterized by four primary parameters - total dissolved inorganic carbon (DIC), total alkalinity (TA), partial pressure of CO2 (pCO2), and pH. These parameters are central to the study of the marine carbon cycle and ocean acidification. Simultaneous measurements of two of the four CO2 parameters are required to fully resolve the seawater CO2 system, and DIC is one of the preferred parameters. A self-calibrating, in-situ sensor, Channelized Optical System (CHANOS), has recently been developed to provide simultaneous measurements of both DIC and pH, resolving carbonate chemistry with a single system. CHANOS is among the first to achieve simultaneous, in-situ measurements of a desired pair of CO2 parameters. DIC and pH channels both use flow-through, spectrophotometric methods to detect relative absorbances of the acid and base forms of a pH-sensitive indicator. The precision of CHANOS in laboratory and in-situ tests are ±0.002 and ±3.0 µmol kg-1 for pH and DIC, respectively. In-situ comparison with bottle sampling and analyses indicate that the accuracies for pH and DIC are ±0.004 and ±5.0 µmol kg-1, respectively. It has been demonstrated that CHANOS can make in-situ, climatology-quality measurements to resolve the CO2 system in dynamic aquatic environments. To further improve response time of the sensor, especially for DIC measurements, a new generation of CHANOS-DIC is under development. The new system adapts the recently developed spectrophotometric DIC method to achieve flow-through CO2 equilibration between an acidified sample and an indicator solution with a response time as fast as 22s. Continuous measurements are also achievable. Because of the fast response of CHANOS measurements, it is versatile and suitable for deployments on both fixed (e.g. buoys) and mobile (e.g., AUV, ROV, and profilers) platforms.

Real Time Assessment of Potable Water Quality in Distribution Network based on Low Cost Multi-Sensor Array

NASA Astrophysics Data System (ADS)

Bhardwaj, Jyotirmoy; Gupta, Karunesh K.; Khatri, Punit

2018-03-01

New concepts and techniques are replacing traditional methods of water quality parameters measurement systems. This paper proposed a new way of potable water quality assessment in distribution network using Multi Sensor Array (MSA). Extensive research suggests that following parameters i.e. pH, Dissolved Oxygen (D.O.), Conductivity, Oxygen Reduction Potential (ORP), Temperature and Salinity are most suitable to detect overall quality of potable water. Commonly MSA is not an integrated sensor array on some substrate, but rather comprises a set of individual sensors measuring simultaneously different water parameters all together. Based on research, a MSA has been developed followed by signal conditioning unit and finally, an algorithm for easy user interfacing. A dedicated part of this paper also discusses the platform design and significant results. The Objective of this proposed research is to provide simple, efficient, cost effective and socially acceptable means to detect and analyse water bodies regularly and automatically.

Chemometric studies of water quality parameters of Sankarankovil block of Tirunelveli, Tamilnadu.

PubMed

Alagumuthu, G; Rajan, M

2010-09-01

The fluoride concentration in ground water was determined in Sankarankovil block of Tirunelveli district of Tamilnadu (India) where it is the only source of drinking water. Various other water quality parameters such as pH, electrical conductivity total hardness and total alkalinity as well as calcium, magnesium, carbonate, bicarbonate and chloride concentrations were also measured. A systematic calculation of correlation coefficient among different physico-chemical parameters was performed. The analytical results indicated considerable variations among the analyzed samples with respect to their chemical composition. Majority of the samples do not comply with Indian as well as WHO water quality standards. The fluoride concentration in the ground water of these villages varied from 0.66 to 3.84 mg l(-1), causes dental fluorosis among people especially children of these villages. The high and low fluoride containing areas were located using isopleth mapping technique. Overall water quality was found unsatisfactory for drinking purposes without any prior treatment except at few locations out of 50 villages.

Groundwater quality in some villages of Haryana, India: focus on fluoride and fluorosis.

PubMed

Meenakshi; Garg, V K; Kavita; Renuka; Malik, Anju

2004-01-02

The fluoride concentration in underground water was determined in four villages of Jind district of Haryana state (India) where it is the only source of drinking water. Various other water quality parameters such as pH, electrical conductivity, total dissolved salts, total hardness, total alkalinity as well as sodium, potassium, calcium, magnesium, carbonate, bicarbonate, chloride and sulfate concentrations were also measured. A systematic calculation of correlation coefficients among different physico-chemical parameters was performed. The analytical results indicated considerable variations among the analyzed samples with respect to their chemical composition. Majority of the samples do not comply with Indian as well as WHO standards for most of the water quality parameters measured. The fluoride concentration in the underground water of these villages varied from 0.3 to 6.9 mg/l, causing dental fluorosis among people especially children of these villages. Overall water quality was found unsatisfactory for drinking purposes without any prior treatment except at eight locations out of 60.

Quality control of positron emission tomography radiopharmaceuticals: An institutional experience.

PubMed

Shukla, Jaya; Vatsa, Rakhee; Garg, Nitasha; Bhusari, Priya; Watts, Ankit; Mittal, Bhagwant R

2013-10-01

To study quality control parameters of routinely prepared positron emission tomography (PET) radiopharmaceuticals. Three PET radiopharmaceuticals fluorine-18 fluorodeoxyglucose (F-18 FDG), N-13 ammonia (N-13 NH3), and Ga-68 DOTATATE (n = 25 each), prepared by standardized protocols were used. The radionuclide purity, radiochemical purity, residual solvents, pH, endotoxins, and sterility of these radiopharmaceuticals were determined. The physical half-life of radionuclide in radiopharmaceuticals, determined by both graphical and formula method, demonstrated purity of radionuclides used. pH of all PET radiopharmaceuticals used was in the range of 5-6.5. No microbial growth was observed in radiopharmaceutical preparations. The residual solvents, chemical impurity, and pyrogens were within the permissible limits. All three PET radiopharmaceuticals were safe for intravenous administration.

Rapid integrated water quality evaluation of Mahisagar river using benthic macroinvertebrates.

PubMed

Bhadrecha, M H; Khatri, Nitasha; Tyagi, Sanjiv

2016-04-01

The water quality of Mahisagar river, near Galteshwar in Kheda district of Gujarat, India, was assessed through a rapid integrated technique by physicochemical parameters as well as benthic macroinvertebrates. Physicochemical parameters retrieved were pH, color, conductivity, total solids, total suspended solids, total dissolved solids, chlorides, total hardness, calcium hardness, magnesium hardness, alkalinity, turbidity, ammoniacal nitrogen, chemical oxygen demand, biochemical oxygen demand, dissolved oxygen, sulfates, and nitrates. The biological indices calculated were BMWP (Bio Monitoring Working Party) score or saprobic score and sequential comparison index or diversity score. In total, 37 families were encountered along the studied river stretch. The findings indicate that the water quality of Mahisagar river at sampled locations is “slightly polluted.” Moreover, the results of physicochemical analysis are also in consonance with the biological water quality criteria developed by Central Pollution Control Board.

Investigating Drought Onset, Termination and Recovery According to Water Quality Indicators

NASA Astrophysics Data System (ADS)

Ahmadi, B.; Moradkhani, H.

2016-12-01

Frequency and severity of droughts are increasing globally. Reduced catchment runoff and river flows caused by the meteorological drivers leads to hydrological drought. Hydrological droughts have significant impacts not only on water quantity but also on water quality. In this study, first the onset of historical hydrological droughts is estimated using daily threshold-based indicators. Then drought termination and recovery period in terms of water quantity is analyzed. This is followed by examination of water quality during these detected hydrological droughts. Four water quality parameters, i.e., water temperature, dissolved oxygen, pH and turbidity are investigated over Willamette river basin located in northwestern Oregon in the United States. Drought vulnerability and resiliency are analyzed for the study period. Droughts and the recovery period are found to have significant impact on water quality parameters. Also, the results indicate a deterioration of water quality during droughts and longer drought recovery if water quality indicators are considered in the analysis.

Quality assessment of rooftop runoff and harvested rainwater from a building catchment.

PubMed

Lee, J Y; Kim, H J; Han, M Y

2011-01-01

A major obstacle to the promotion of rainwater harvesting is chemical and microbiological concerns. To determine its suitability as an alternative water resource, water quality parameters such as pH, turbidity and metal ion concentrations and counted total coliform, Escherichia coli and heterotrophic bacteria were measured. It was observed that the stored rainwater had a neutral average pH and that its turbidity depended on the duration and intensity of the rainfall event. Metal concentrations were within the permissible limits specified in the Korea drinking water standard. In addition, counts of coliform, E. coli and heterotrophic bacteria were higher in the first flush 5 min after the start of the rainfall event. Principal component analysis and correlation analysis through 40 events in 2009 showed that the quality of stored rainwater depends on the conditions of the catchment and storage tank and the antecedent dry period.

Monitoring and assessment of water quality of Tasik Cempaka, Bangi

NASA Astrophysics Data System (ADS)

Sabri, Nurul Ain Syahirah Mohamad; Abdullah, Md Pauzi; Mat, Sohif

2014-09-01

A study was carried out to determine the status of water quality of Tasik Cempaka which is a part of Sg. Air Itam, located near the Bangi industrial area. The study was carried out for eight months from May and to December 2013. Eight sampling stations were selected from upstream to downstream of Sg. Air Itam which represent the entire body of the lake water. There are 8 parameters measured and Water Quality Indices (WQI) was calculated and classified according to the National Water Quality Standard (NWQS). The physical and chemical parameters were temperature, pH, conductivity, dissolve oxygen (DO), total suspended solid (TSS), ammoniacal nitrogen (AN), chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Among parameters that are affected by pollution is AN, COD and BOD. Classification by WQI shows that the average for all sampling was 54 (dry) and 52 (wet). Both are of class III according to National Water Quality Standard (NWQS) indicating slightly polluted. This is mainly due to drainage from Bangi Golf Resort and Bangi-Putrajaya Hotel. Other factors are activities around Sg. Air Itam such as municipal activities, settlements and manufacturing industries.

Statistical, time series, and fractal analysis of full stretch of river Yamuna (India) for water quality management.

PubMed

Parmar, Kulwinder Singh; Bhardwaj, Rashmi

2015-01-01

River water is a major resource of drinking water on earth. Management of river water is highly needed for surviving. Yamuna is the main river of India, and monthly variation of water quality of river Yamuna, using statistical methods have been compared at different sites for each water parameters. Regression, correlation coefficient, autoregressive integrated moving average (ARIMA), box-Jenkins, residual autocorrelation function (ACF), residual partial autocorrelation function (PACF), lag, fractal, Hurst exponent, and predictability index have been estimated to analyze trend and prediction of water quality. Predictive model is useful at 95% confidence limits and all water parameters reveal platykurtic curve. Brownian motion (true random walk) behavior exists at different sites for BOD, AMM, and total Kjeldahl nitrogen (TKN). Quality of Yamuna River water at Hathnikund is good, declines at Nizamuddin, Mazawali, Agra D/S, and regains good quality again at Juhikha. For all sites, almost all parameters except potential of hydrogen (pH), water temperature (WT) crosses the prescribed limits of World Health Organization (WHO)/United States Environmental Protection Agency (EPA).

Genetic and phenotypic parameters for carcass and meat quality traits in commercial crossbred pigs.

PubMed

Miar, Y; Plastow, G S; Moore, S S; Manafiazar, G; Charagu, P; Kemp, R A; Van Haandel, B; Huisman, A E; Zhang, C Y; McKay, R M; Bruce, H L; Wang, Z

2014-07-01

Pork quality and carcass characteristics are now being integrated into swine breeding objectives because of their economic value. Understanding the genetic basis for these traits is necessary for this to be accomplished. The objective of this study was to estimate phenotypic and genetic parameters for carcass and meat quality traits in 2 Canadian swine populations. Data from a genomic selection study aimed at improving meat quality with a mating system involving hybrid Landrace × Large White and Duroc pigs were used to estimate heritabilities and phenotypic and genetic correlations among them. Data on 2,100 commercial crossbred pigs for meat quality and carcass traits were recorded with pedigrees compromising 9,439 animals over 15 generations. Significant fixed effects (company, sex, and slaughter batch), covariates (cold carcass weight and slaughter age), and random additive and common litter effects were fitted in the models. A series of pairwise bivariate analyses were implemented in ASReml to estimate phenotypic and genetic parameters. Heritability estimates (±SE) for carcass traits were moderate to high and ranged from 0.22 ± 0.08 for longissimus dorsi muscle area to 0.63 ± 0.04 for trimmed ham weight, except for firmness, which was low. Heritability estimates (±SE) for meat quality traits varied from 0.10 ± 0.04 to 0.39 ± 0.06 for the Minolta b* of ham quadriceps femoris muscle and shear force, respectively. Generally, most of the genetic correlations were significant (P < 0.05) and ranged from low (0.18 ± 0.07) to high (-0.97 ± 0.35). There were high negative genetic correlations between drip loss with pH and shear force and a positive correlation with cooking loss. Genetic correlations between carcass weight (both hot and cold) with carcass marbling were highly positive. It was concluded that selection for increasing primal and subprimal cut weights with better pork quality may be possible. Furthermore, the use of pH is confirmed as an indicator for pork water-holding capacity and cooking loss. The heritabilities of carcass and pork quality traits indicated that they can be improved using traditional breeding methods and genomic selection, respectively. The estimated genetic parameters for carcass and meat quality traits can be incorporated into the breeding programs that emphasize product quality in these Canadian swine populations.

Surface water quality in streams and rivers: introduction, scaling, and climate change: Chapter 5

USGS Publications Warehouse

Loperfido, John

2013-01-01

A variety of competing and complementary needs such as ecological health, human consumption, transportation, recreation, and economic value make management and protection of water resources in riverine environments essential. Thus, an understanding of the complex and interacting factors that dictate riverine water quality is essential in empowering stake-holders to make informed management decisions (see Chapter 1.15 for additional information on water resource management). Driven by natural and anthropogenic forcing factors, a variety of chemical, physical, and biological processes dictate riverine water quality, resulting in temporal and spatial patterns and cycling (see Chapter 1.2 for information describing how global change interacts with water resources). Furthermore, changes in climatic forcing factors may lead to long-term deviations in water quality outside the envelope of historical data. The goal of this chapter is to present fundamental concepts dictating the conditions of basic water quality parameters in rivers and streams (herein generally referred to as rivers unless discussing a specific system) in the context of temporal (diel (24 h) to decadal) longitudinal scaling. Understanding water quality scaling in rivers is imperative as water is continually reused and recycled (see also Chapters 3.1 and 3.15); upstream discharges from anthropogenic sources are incorporated into bulk riverine water quality that is used by downstream consumers. Water quality parameters reviewed here include temperature, pH, dissolved oxygen (DO), and suspended sediment and were selected given the abundance of data available for these parameters due to recent advances in water quality sensor technology (see Chapter 4.13 for use of hydrologic data in watershed management). General equations describing reactions affecting water temperature, pH, DO, and suspended sediment are included to convey the complexity of how simultaneously occurring reactions can affect water quality in rivers. Concepts presented in this chapter will provide a backdrop that other chapters in this book will explore further, including water quality in the following riverine systems: the Mississippi River (see Chapter 4.9), Hudson River (see Chapter 4.6), and rivers in India (see Chapter 4.10).

The effect of nisin from Lactococcus lactis subsp. lactis on refrigerated patin fillet quality

NASA Astrophysics Data System (ADS)

Adilla, S. N.; Utami, R.; Nursiwi, A.; Nurhartadi, E.

2017-04-01

The effect of nisin from Lactococcus lactis subsp. lactis with spraying method application on quality of patin fillet during refrigerated storage (4±1°C) was investigated. The quality of patin fillet based on total plate count (TPC), pH, TVB-N, and TBA values during 16 days at 4±1°C. Completely Randomized Design (CDR) was used in one factor (nisin activity) at 0 IU/ml, 500 IU/ml, 1000 IU/ml, and 2000 IU/ml. The observation was done at 0, 4th, 8th, 12th, and 16th days of storage. The result showed that variation of nisin activity significantly affected the quality of fillet according to TPC, pH, and TVB-N values, however no significant difference on the obtained of TBA value. Nisin in 500 IU/ml, 1000 IU/ml, and 2000 IU/ml could extend the shelf-life of fillet until 4th, 8th, and 12th days respectively based on standard in all parameters.

Optimisation of shock absorber process parameters using failure mode and effect analysis and genetic algorithm

NASA Astrophysics Data System (ADS)

Mariajayaprakash, Arokiasamy; Senthilvelan, Thiyagarajan; Vivekananthan, Krishnapillai Ponnambal

2013-07-01

The various process parameters affecting the quality characteristics of the shock absorber during the process were identified using the Ishikawa diagram and by failure mode and effect analysis. The identified process parameters are welding process parameters (squeeze, heat control, wheel speed, and air pressure), damper sealing process parameters (load, hydraulic pressure, air pressure, and fixture height), washing process parameters (total alkalinity, temperature, pH value of rinsing water, and timing), and painting process parameters (flowability, coating thickness, pointage, and temperature). In this paper, the process parameters, namely, painting and washing process parameters, are optimized by Taguchi method. Though the defects are reasonably minimized by Taguchi method, in order to achieve zero defects during the processes, genetic algorithm technique is applied on the optimized parameters obtained by Taguchi method.

Phenotypic and genetic relationships between indicators of the mammary gland health status and milk composition, coagulation, and curd firming in dairy sheep.

PubMed

Pazzola, Michele; Cipolat-Gotet, Claudio; Bittante, Giovanni; Cecchinato, Alessio; Dettori, Maria L; Vacca, Giuseppe M

2018-04-01

The present study investigated the effect of somatic cell count, lactose, and pH on sheep milk composition, coagulation properties (MCP), and curd firming (CF) parameters. Individual milk samples were collected from 1,114 Sarda ewes reared in 23 farms. Milk composition, somatic cell count, single point MCP (rennet coagulation time, RCT; curd firming time, k 20 ; and curd firmness, a 30 , a 45 , and a 60 ), and CF model parameters were achieved. Phenotypic traits were statistically analyzed using a mixed model to estimate the effects of the different levels of milk somatic cell score (SCS), lactose, and pH, respectively. Additive genetic, herd, and residual correlations among these 3 traits, and with milk composition, MCP and CF parameters, were inferred using a Bayesian approach. From a phenotypic point of view, higher SCS levels caused a delayed gelification of milk. Lactose concentration and pH were significant for many milk quality traits, with a very intense effect on both coagulation times and curd firming. These traits (RCT, RCT estimated using the curd firming over time equation, and k 20 ) showed an unfavorable increase of about 20% from the highest to the lowest level of lactose. Milk samples with pH values lower than 6.56 versus higher than 6.78 were characterized by an increase of RCT (from 6.00 to 14.3 min) and k 20 (from 1.65 to 2.65 min) and a decrease of all the 3 curd firmness traits. From a genetic point of view, the marginal posterior distribution of heritability estimates evidenced a large and exploitable variability for all 3 phenotypes. The mean intra-farm heritability estimates were 0.173 for SCS, 0.418 for lactose content, and 0.206 for pH. Lactose (favorably), and SCS and pH (unfavorably), at phenotypic and genetic levels, were correlated mainly with RCT and RCT estimated using the curd firming over time equation and scarcely with the other curd firming traits. The SCS, lactose, and pH were significantly correlated with each other's. In conclusion, results reported in the present study suggest that SCS, pH, and lactose affect, contemporarily and independently, milk quality and MCP. These phenotypes, easily available during milk recording schemes measured by infrared spectra prediction, could be used as potential indicators traits for improving cheese-making ability of ovine milk. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Analysis of the spatio-temporal variability of seawater quality in the southeastern Arabian Gulf.

PubMed

Mezhoud, Nahla; Temimi, Marouane; Zhao, Jun; Al Shehhi, Maryam Rashed; Ghedira, Hosni

2016-05-15

In this study, seawater quality measurements, including salinity, sea surface temperature (SST), chlorophyll-a (Chl-a), Secchi disk depth (SDD), pH, and dissolved oxygen (DO), were made from June 2013 to November 2014 at 52 stations in the southeastern Arabian Gulf. Significant variability was noticed for all collected parameters. Salinity showed a decreasing trend, and Chl-a, DO, pH, and SDD demonstrated increasing trends from shallow onshore stations to deep offshore ones, which could be attributed to variations of ocean circulation and meteorological conditions from onshore to offshore waters, and the likely effects of desalination plants along the coast. Salinity and temperature were high in summer and low in winter while Chl-a, SDD, pH, and DO indicated an opposite trend. The CTD profiles showed vertically well-mixed structures. Qualitative analysis of phytoplankton showed a high diversity of species without anomalous species found except in Ras Al Khaimah stations where diatoms were the dominating ones. Copyright © 2016 Elsevier Ltd. All rights reserved.

Lignin recovery and it effects quality of anaerobic treated palm oil mill effluent (AT-POME)

NASA Astrophysics Data System (ADS)

Haqi Ibrahim, Abdul; Fahmi Ridwan, Muhammad; Zulzikrami Azner Abidin, Che; Ong, Soon Ann; Shian Wong, Yee; Wazira Azhari, Ayu; Norruhaidawati Ozir, Siti

2018-03-01

Lignin is one of the main structural polymers present in plant tissue. It can also be found as an isolated product of the pulp and paper industry. Palm oil mill effluent (POME) has been known as high strength industrial wastewater that is difficult to treat due to its large variety of inorganic and organic contents. The main purpose of this study is to recover soluble lignin from anaerobically treated palm oil mill effluent (AT-POME) and indirectly improves the quality of AT-POME. AT-POME was adjusted to different pH using different type of acids. Response Surface Methodology (RSM) was utilized to obtain the optimum operating parameters as well as to analyse the interaction between them. Model shows that 74.67 % of lignin can be recovered from AT-POME after 5 minutes reaction time using sulfuric acid (H2S04) at pH 5. Hence from the experiment, it was proved that simple pH adjustment could precipitate the soluble lignin from AT-POME.

SNPs detection in DHPS-WDR83 overlapping genes mapping on porcine chromosome 2 in a QTL region for meat pH.

PubMed

Zambonelli, Paolo; Davoli, Roberta; Bigi, Mila; Braglia, Silvia; De Paolis, Luigi Francesco; Buttazzoni, Luca; Gallo, Maurizio; Russo, Vincenzo

2013-10-08

The pH is an important parameter influencing technological quality of pig meat, a trait affected by environmental and genetic factors. Several quantitative trait loci associated to meat pH are described on PigQTL database but only two genes influencing this parameter have been so far detected: Ryanodine receptor 1 and Protein kinase, AMP-activated, gamma 3 non-catalytic subunit. To search for genes influencing meat pH we analyzed genomic regions with quantitative effect on this trait in order to detect SNPs to use for an association study. The expressed sequences mapping on porcine chromosomes 1, 2, 3 in regions associated to pork pH were searched in silico to find SNPs. 356 out of 617 detected SNPs were used to genotype Italian Large White pigs and to perform an association analysis with meat pH values recorded in semimembranosus muscle at about 1 hour (pH1) and 24 hours (pHu) post mortem.The results of the analysis showed that 5 markers mapping on chromosomes 1 or 3 were associated with pH1 and 10 markers mapping on chromosomes 1 or 2 were associated with pHu. After False Discovery Rate correction only one SNP mapping on chromosome 2 was confirmed to be associated to pHu. This polymorphism was located in the 3'UTR of two partly overlapping genes, Deoxyhypusine synthase (DHPS) and WD repeat domain 83 (WDR83). The overlapping of the 3'UTRs allows the co-regulation of mRNAs stability by a cis-natural antisense transcript method of regulation. DHPS catalyzes the first step in hypusine formation, a unique amino acid formed by the posttranslational modification of the protein eukaryotic translation initiation factor 5A in a specific lysine residue. WDR83 has an important role in the modulation of a cascade of genes involved in cellular hypoxia defense by intensifying the glycolytic pathway and, theoretically, the meat pH value. The involvement of the SNP detected in the DHPS/WDR83 genes on meat pH phenotypic variability and their functional role are suggestive of molecular and biological processes related to glycolysis increase during post-mortem phase. This finding, after validation, can be applied to identify new biomarkers to be used to improve pig meat quality.

[Influence of water source switching on water quality in drinking water distribution system].

PubMed

Wang, Yang; Niu, Zhang-bin; Zhang, Xiao-jian; Chen, Chao; He, Wen-jie; Han, Hong-da

2007-10-01

This study investigates the regularity of the change on the physical and chemical water qualities in the distribution system during the process of water source switching in A city. Due to the water source switching, the water quality is chemical-astable. Because of the differences between the two water sources, pH reduced from 7.54 to 7.18, alkalinity reduced from 188 mg x L(-1) to 117 mg x L(-1), chloride (Cl(-)) reduced from 310 mg x L(-1) to 132 mg x L(-1), conductance reduced from 0.176 S x m(-1) to 0.087 S x m(-1) and the ions of calcium and magnesium reduced to 15 mg x L(-1) and 11 mg x L(-1) respectively. Residual chlorine changed while the increase of the chlorine demand and the water quantity decreasing at night, and the changes of pH, alkalinity and residual chlorine brought the iron increased to 0.4 mg x L(-1) at the tiptop, which was over the standard. The influence of the change of the water parameters on the water chemical-stability in the drinking water distribution system is analyzed, and the controlling countermeasure is advanced: increasing pH, using phosphate and enhancing the quality of the water in distribution system especially the residual chlorine.

Comparative analysis of time-scaling properties about water pH in Poyang Lake Inlet and Outlet on the basis of fractal methods.

PubMed

Shi, K; Liu, C Q; Huang, Z W; Zhang, B; Su, Y

2010-01-01

Detrended fluctuation analysis (DFA) and multifractal methods are applied to the time-scaling properties analysis of water pH series in Poyang Lake Inlet and Outlet in China. The results show that these pH series are characterised by long-term memory and multifractal scaling, and these characteristics have obvious differences between the Lake Inlet and Outlet. The comparison results suggest that monofractal and multifractal parameters can be quantitative dynamical indexes reflecting the capability of anti-acidification of Poyang Lake. Furthermore, we investigated the frequency-size distribution of pH series in Poyang Lake Inlet and Outlet. Our findings suggest that water pH is an example of a self-organised criticality (SOC) process. The results show that it is different SOC behaviours that result in the differences of power-law relations between pH series in Poyang Lake Inlet and Outlet. This work can be helpful to improvement of modelling of lake water quality.

Evaluation of water quality index for River Sabarmati, Gujarat, India

NASA Astrophysics Data System (ADS)

Shah, Kosha A.; Joshi, Geeta S.

2017-06-01

An attempt has been made to develop water quality index (WQI), using six water quality parameters pH, dissolved oxygen, biochemical oxygen demand, electrical conductivity, nitrate nitrogen and total coliform measured at three different stations along the Sabarmati river basin from the year 2005 to 2008. Rating scale is developed based on the tolerance limits of inland waters and health point of view. Weighted arithmetic water quality index method was used to find WQI along the stretch of the river basin. It was observed from this study that the impact of human activity and sewage disposal in the river was severe on most of the parameters. The station located in highly urban area showed the worst water quality followed by the station located in moderately urban area and lastly station located in a moderately rural area. It was observed that the main cause of deterioration in water quality was due to the high anthropogenic activities, illegal discharge of sewage and industrial effluent, lack of proper sanitation, unprotected river sites and urban runoff.

Effect of pumpkin on the quality characteristics and storage quality of aerobically packaged chicken sausages.

PubMed

Zargar, Fayaz Ahmed; Kumar, Sunil; Bhat, Zuhaib Fayaz; Kumar, Pavan

2014-01-01

The present study was undertaken to evaluate the effect of different levels of pumpkin on the quality characteristics of chicken sausages. The pumpkin was incorporated at three different levels viz. 6, 12 and 18 percent replacing lean meat in the formulation. The products were analyzed for various physicochemical and sensory attributes. pH, emulsion stability, cooking yield, crude protein, ether extract and ash content of the products showed significantly (p < 0.05) decreasing trend with increasing levels of incorporation of pumpkin however, there was a significant (p < 0.05) increase in the moisture and crude fibre content. Based on various parameters, 12 percent level of incorporation was optimized as best. Chicken sausages with optimum level of pumpkin along with control were aerobically packaged in LDPE pouches and assessed for storage quality under refrigerated (4 ± 1°C) conditions. The mean values of pH and all the sensory parameters showed significantly (p < 0.05) decreasing trend for both control as well as treatment samples whereas TBARS (mg malonaldehyde/kg) value, total plate count (log cfu/g) and yeast and mould count (log cfu/g) showed significantly (p < 0.05) increasing trend with storage. Coliforms (log cfu/g) were not detected throughout the period of storage. Thus, fibre enriched chicken sausages could be successfully stored for a period of 14 days at refrigeration temperature (4 ± 1°C) without any significant loss in quality.

Number of independent parameters in the potentiometric titration of humic substances.

PubMed

Lenoir, Thomas; Manceau, Alain

2010-03-16

With the advent of high-precision automatic titrators operating in pH stat mode, measuring the mass balance of protons in solid-solution mixtures against the pH of natural and synthetic polyelectrolytes is now routine. However, titration curves of complex molecules typically lack obvious inflection points, which complicates their analysis despite the high-precision measurements. The calculation of site densities and median proton affinity constants (pK) from such data can lead to considerable covariance between fit parameters. Knowing the number of independent parameters that can be freely varied during the least-squares minimization of a model fit to titration data is necessary to improve the model's applicability. This number was calculated for natural organic matter by applying principal component analysis (PCA) to a reference data set of 47 independent titration curves from fulvic and humic acids measured at I = 0.1 M. The complete data set was reconstructed statistically from pH 3.5 to 9.8 with only six parameters, compared to seven or eight generally adjusted with common semi-empirical speciation models for organic matter, and explains correlations that occur with the higher number of parameters. Existing proton-binding models are not necessarily overparametrized, but instead titration data lack the sensitivity needed to quantify the full set of binding properties of humic materials. Model-independent conditional pK values can be obtained directly from the derivative of titration data, and this approach is the most conservative. The apparent proton-binding constants of the 23 fulvic acids (FA) and 24 humic acids (HA) derived from a high-quality polynomial parametrization of the data set are pK(H,COOH)(FA) = 4.18 +/- 0.21, pK(H,Ph-OH)(FA) = 9.29 +/- 0.33, pK(H,COOH)(HA) = 4.49 +/- 0.18, and pK(H,Ph-OH)(HA) = 9.29 +/- 0.38. Their values at other ionic strengths are more reliably calculated with the empirical Davies equation than any existing model fit.

78 FR 59555 - Endangered and Threatened Wildlife and Plants; Designation of Critical Habitat for the Fluted...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-26

... physical and chemical water quality parameters (such as temperature, dissolved oxygen, pH, and conductivity... unknown. High temperatures can reduce dissolved oxygen concentrations in the water, which slows growth... encystment, increase oxygen consumption, reduce the speed in which they orient themselves in the substrate...

Assessment of beer quality based on foamability and chemical composition using computer vision algorithms, near infrared spectroscopy and machine learning algorithms.

PubMed

Gonzalez Viejo, Claudia; Fuentes, Sigfredo; Torrico, Damir; Howell, Kate; Dunshea, Frank R

2018-01-01

Beer quality is mainly defined by its colour, foamability and foam stability, which are influenced by the chemical composition of the product such as proteins, carbohydrates, pH and alcohol. Traditional methods to assess specific chemical compounds are usually time-consuming and costly. This study used rapid methods to evaluate 15 foam and colour-related parameters using a robotic pourer (RoboBEER) and chemical fingerprinting using near infrared spectroscopy (NIR) from six replicates of 21 beers from three types of fermentation. Results from NIR were used to create partial least squares regression (PLS) and artificial neural networks (ANN) models to predict four chemometrics such as pH, alcohol, Brix and maximum volume of foam. The ANN method was able to create more accurate models (R 2  = 0.95) compared to PLS. Principal components analysis using RoboBEER parameters and NIR overtones related to protein explained 67% of total data variability. Additionally, a sub-space discriminant model using the absorbance values from NIR wavelengths resulted in the successful classification of 85% of beers according to fermentation type. The method proposed showed to be a rapid system based on NIR spectroscopy and RoboBEER outputs of foamability that can be used to infer the quality, production method and chemical parameters of beer with minimal laboratory equipment. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Assessment of the quality of water from hand-dug wells in ghana.

PubMed

Nkansah, Marian Asantewah; Boadi, Nathaniel Owusu; Badu, Mercy

2010-04-26

This study focused upon the determination of physicochemical and microbial properties, including metals, selected anions and coliform bacteria in drinking water samples from hand-dug wells in the Kumasi metropolis of the Republic of Ghana. The purpose was to assess the quality of water from these sources. Ten different water samples were taken from different parts of Kumasi, the capital of the Ashanti region of Ghana and analyzed for physicochemical parameters including pH, electrical conductivity, total dissolved solids, alkalinity total hardness and coliform bacteria. Metals and anions analyzed were Ca, Mg, Fe, Mn, NO(3) (-), NO(2) (-), SO(4) (2-), PO(4) (2-), F(-) and Cl(-). Bacteria analysed were total coliform and Escherichia coli.THE DATA SHOWED VARIATION OF THE INVESTIGATED PARAMETERS IN SAMPLES AS FOLLOWS: pH, 6.30-0.70; conductivity (EC), 46-682 muS/cm; PO(4) (3-), 0.67-76.00 mg/L; F(-), 0.20-0.80 mg/L; NO(3) (-), 0-0.968 mg/L; NO(2) (-), 0-0.063 mg/L; SO(4) (2-), 3.0-07.0 mg/L; Fe, 0-1.2 mg/L; Mn, 0-0.018 mg/L. Total coliform and Escherichia coli were below the minimum detection limit (MDL) of 20 MPN per 100 ml in all the samples. The concentrations of most of the investigated parameters in the drinking water samples from Ashanti region were within the permissible limits of the World Health Organization drinking water quality guidelines.

Vermicomposting of food waste: assessing the stability and maturity

PubMed Central

2012-01-01

The vermicompost using earthworms (Eisenia Fetida) was produced from food waste and chemical parameters (EC, pH, carbon to nitrogen contents (C/N)) and germination bioassay was examined in order to assess the stability and maturity indicators during the vermicomposting process. The seed used in the germination bioassay was cress. The ranges of EC, pH, C/N and germination index were 7.5-4.9 mS/cm, 5.6-7.53, 30.13-14.32% and 12.8-58.4%, respectively. The germination index (GI) value revealed that vermicompost rendered as moderate phytotoxic to cress seed. Pearson correlation coefficient was used to evaluate the relationship between the parameters. High statistically significant correlation coefficient was calculated between the GI value and EC in the vermicompost at the 99% confidence level. The C/N value showed that the vermicompost was stable. As a result of these observations, stability test alone, was not able to ensure high vermicompost quality. Therefore, it appears that determining vermicompost quality requires a simultaneous use of maturity and stability tests. PMID:23369642

Temporal variations of groundwater quality in the Western Jianghan Plain, China.

PubMed

Niu, Beibei; Wang, Huanhuan; Loáiciga, Hugo A; Hong, Song; Shao, Wei

2017-02-01

The Western Jianghan Plain (WJHP) lies in the middle reaches of the Yangtze River. It has been impacted by anthropogenic activities during the past decades. The long-term variations of the WJHP's regional aquifer's hydrochemistry and groundwater quality have not been previously assessed. Sixteen physiochemical parameters at 29 monitoring wells within the Western Jianghan Plain were monitored during 1992-2010 and analyzed with multiple approaches. The confined groundwater is predominantly of the HCO 3 -Ca-Mg type with Cl - , SO 4 2- , NH 4 -N, and NO 3 -N showing remarkable spatial variations. Correlation analysis was used to identify the origins and contamination sources of groundwater. The seasonal Mann-Kendall test revealed that pH, NO 3 -N, and Cl - concentrations at 27, 26 and 15 wells, respectively, exhibited significant increasing trends during 1992-2010. The increase of pH may be attributed to CO 2 degassing caused by extensive groundwater extraction. Regional average NO 3 -N concentrations of groundwater increased coincidently with the increased use of fertilizer, which suggests that nitrate pollution is caused by agricultural activities. Abnormally high values of Cl - and SO 4 2- at some wells were induced by industrial chemicals. In addition, the similarity of the temporal variations of the regional average of pH, NH 4 -N, and NO 3 -N concentrations in groundwater with those in the Yangtze River at the outlet of the Three Gorges Reservoir (TGR) suggests that the variations of these parameters in the WJHP is partly due to water storage by the TGR. This study presents an analysis of temporal variations of groundwater quality in the WJHP that reveals a relation between the creation of the TGR and downstream groundwater quality. This paper's findings provide clues for measures that could be taken to protect the groundwater quality of the WJHP's aquifer. Copyright © 2016. Published by Elsevier B.V.

Influence of carbon dioxide stunning procedure on quality of turkey meat.

PubMed

Mauri, S; Guijarro, A; Avilés, C; Peña, F

2017-08-01

1. The objective of this study was to evaluate the effect of sex and gas stunning on quality attributes of turkey breast meat. 2. One hundred B.U.T. Premium turkeys (50 males and 50 females) were divided into four groups of 25 animals and subjected to one of two CO 2 stunning procedures: G1 stepwise (step 1: 30% CO 2 , 15 s; step 2: 55% CO 2 , 40 s; step 3: 70% CO 2 , 45 s) or G2 fixed concentration (80% CO 2 , 100 s). The pH and meat colour at 20 min post-mortem, and pH, colour (L*, a*, b*), water holding capacity (WHC), drip loss (DL), cooking loss (CL) and Warner-Bratzler shear force (WBSF) in breast samples at 24 h and 7 d post-mortem were assessed. 3. There were significant differences between stunning groups for pH, meat colour and CL, whereas no significant differences were found for DL and WBSF. Sex had a significant effect on pH and b* and ageing of meat affected pH, colour coordinates, DL and WBSF. 4. It was concluded that the G2 treatment affected negatively the pH value and colour coordinates. However, G2 stunning affected positively the WHC parameters. Female turkeys had better results than males for pH, and the colour of female turkey breast meat was less yellow than male breast meat.

The utility of oesophageal pH monitoring in diagnosing gastroesophageal reflux disease-related chronic cough.

PubMed

Rybka, Aleksandra; Malesa, Kamila; Radlińska, Olga; Krakowiak, Karolina; Grabczak, Elżbieta M; Dąbrowska, Marta; Chazan, Ryszarda

2014-01-01

Chronic cough is a common medical complaint, which may deteriorate patients' quality of life and cause many complications. Gastroesophageal reflux disease (GERD) is one of the frequent reasons for chronic cough. Oesophageal pH monitoring is one of the diagnostic methods performed to confirm diagnosis of GERD-related cough. The aim of the study was to analyse the utility of oesophageal pH monitoring in diagnosing GERD-related cough and to identify the most sensitive pH monitoring parameters for diagnosing GERD-related cough. 24-hour oesophageal pH monitoring was performed in 204 patients suffering from chronic cough. The group consisted of 65% females and the median age was 59 years. An acid reflux episode was defined as a rapid drop in pH to a value below 4 for at least 12 seconds. The diagnosis of GERD was based on total fraction time of pH < 4, upright or supine fraction time of pH < 4, or DeMeester score. The diagnosis of GERD-related cough was made if cough episodes, marked by the patients, appeared within 2 minutes after the reflux. The association between reflux episode and appearance of cough was analysed using two parameters: symptom index (SI ≥ 50%) and/or symptom association probability (SAP ≥ 95%). Based on results of pH monitoring, 135 patients (135/204, 66%) were diagnosed with GERD. Among them, 117 patients (117/135, 87%) were diagnosed based on DeMeester score. Among patients with GERD, 61 patients met the criteria of GERD-related cough (61/135, 45%), i.e. 30% of the group as a whole. Thirty-six patients (36/61, 59%) were diagnosed based on SAP, 12 patients (20%) based on SI, and 13 (21%) based on both parameters. Spearman rank correlation coefficient for SAP ≥ 95% and SI ≥ 50% was 0.46 (p < 0.05). Based on pH monitoring results, GERD was diagnosed twice as often as GERD-related cough. SAP index is more sensitive than SI for the diagnosis of GERD-related cough.

Microbiological assessment, nutritional characterization and phenolic compounds of bee pollen from Mellipona mandacaia Smith, 1983.

PubMed

Bárbara, Marivalda Santa; Machado, Cerilene Santiago; Sodré, Geni da Silva; Dias, Luís G; Estevinho, Leticia M; de Carvalho, Carlos Alfredo Lopes

2015-07-09

This study aims to assess the microbiological parameters and the chemical composition of 21 samples of stingless bee pollen (Melipona mandacaia) from two regions of Bahia, Brazil (João Dourado and Uibaí), with particular emphasis on the nutritional value, total phenols and flavonoids and fatty acids composition. Regarding the microbiological quality, the studied microorganisms (moulds and yeasts, coliforms, Escherichia coli, Staphylococcus aureus, Salmonella sp., psychrotrophic and sulfite-reducing Clostridia) were absent in all samples. On the other hand, the values obtained for the aerobic mesophilic microorganism ranged from 11.0 ± 1.0 to 1.32 ± 1.2 cfu∙g(-)(1) (JD samples) and from 282 ± 3.82 to 688 ± 10.1 cfu∙g(-)(1) (U samples). The nutritional parameters (moisture, ash, water activity, pH, total acidity, protein, fiber, total phenolic, flavonoids and reducing sugars) were within the stipulated by law, except for pH and moisture content, which presented superior and inferior values, respectively. Polyunsaturated fatty acids (54.1%) were significantly higher than saturated (42.18%) and monounsaturated (3.71%). It was found that the bee pollen is safe from the microbiological point of view and has a good nutritional quality. The influence of the geographical origin on the assessed parameters was evident, especially concerning the fatty acid profile.

Microbiological Assessment, Nutritional Characterization and Phenolic Compounds of Bee Pollen from Mellipona mandacaia Smith, 1983.

PubMed

Bárbara, Marivalda Santa; Machado, Cerilene Santiago; Sodré, Geni da Silva; Dias, Luís G; Estevinho, Leticia M; de Carvalho, Carlos Alfredo Lopes

2015-07-09

This study aims to assess the microbiological parameters and the chemical composition of 21 samples of stingless bee pollen (Melipona mandacaia) from two regions of Bahia, Brazil (João Dourado and Uibaí), with particular emphasis on the nutritional value, total phenols and flavonoids and fatty acids composition. Regarding the microbiological quality, the studied microorganisms (moulds and yeasts, coliforms, Escherichia coli, Staphylococcus aureus, Salmonella sp., psychrotrophic and sulfite-reducing Clostridia) were absent in all samples. On the other hand, the values obtained for the aerobic mesophilic microorganism ranged from 11.0 ± 1.0 to 1.32 ± 1.2 cfu∙g-1 (JD samples) and from 282 ± 3.82 to 688 ± 10.1 cfu∙g-1 (U samples). The nutritional parameters (moisture, ash, water activity, pH, total acidity, protein, fiber, total phenolic, flavonoids and reducing sugars) were within the stipulated by law, except for pH and moisture content, which presented superior and inferior values, respectively. Polyunsaturated fatty acids (54.1%) were significantly higher than saturated (42.18%) and monounsaturated (3.71%). It was found that the bee pollen is safe from the microbiological point of view and has a good nutritional quality. The influence of the geographical origin on the assessed parameters was evident, especially concerning the fatty acid profile.

Effect of dietary plant extract on meat quality and sensory parameters of meat from Equidae.

PubMed

Rossi, Raffaella; Ratti, Sabrina; Pastorelli, Grazia; Maghin, Federica; Martemucci, Giovanni; Casamassima, Donato; D'Alessandro, Angela Gabriella; Corino, Carlo

2017-11-01

Plant extracts as Lippia spp. have been proven antioxidant properties. Recent studies have been shown that dietary supplementation with plant extracts is able to enhance meat quality parameters. Studies regarding meat quality in Equidae are limited. The effect of dietary plant extract (PE), containing verbascoside, on meat quality, oxidative stability and sensory parameters of Longissimus Lumborum (LL) muscle in Equidae was studied. Dietary treatment did not affect (P > 0.05) pH, colour indices and chemical parameters of muscle in both donkey and horse. Dietary PE improved (P < 0.01) oxidative stability in donkey muscle during refrigerated storage. Sensory characteristics of LL muscle were positively affected (P < 0.05) by dietary PE in both donkey and horse. In particular, colour, taste and texture were enhanced in LL muscle from animals fed PE. Oxidative stability was lower (P < 0.05) in LL muscle of horse than that of donkey. Dietary plant extract, containing verbascoside, can be considered as a natural source of antioxidants, and is also able to improve oxidative stability of donkey meat and to affect the sensory attributes of Equidae meat. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Evaluation of physico-chemical characteristics of groundwater of Company Bagh pumping station and its six distribution points in old Jammu City, India.

PubMed

Khajuria, Meenakshi; Dutta, S P S

2011-10-01

To assess water quality of Company Bagh pumping station and its six distribution points, viz. Parade Ground, Mohalla Paharian, Purani Mandi, Malhotrian Street, Raghunathpura and Hari Market in old Jammu city of India, water parameters viz. temperature, turbidity, pH, electrical conductivity, free carbon dioxide, dissolved oxygen, biochemical oxygen demand, chemical oxygen demand, bicarbonate, chloride, calcium, magnesium, total hardness, sodium, potassium, sulphate, silicate, nitrate, phosphate, iron, copper, zinc, lead and chromium were analyzed during the years 2000-2001/2001-2002. There was alteration in water quality parameters in the distribution system caused by entry of sewage, soil, etc. through dislocation, cracks, valve regulators/turncock, defective joints, breakage, etc. in the pipes through crossing and deposits of biofilms inside the pipes, dead ends and their degradation through microbes. Comparison of water quality with National and International Standards revealed that all the parameters were within permissible limits of drinking water standards. Water Quality Index (WQI) of various physico-chemical parameters revealed that the water of Company Bagh pumping station and its six distribution points was fit for human consumption as it was found under the category of good (WQI < 50).

Changes in soil parameters under continuous plastic mulching in strawberry cultivation

NASA Astrophysics Data System (ADS)

Muñoz, Katherine; Diehl, Dörte; Scopchanova, Sirma; Schaumann, Gabriele E.

2016-04-01

Plastic mulching (PM) is a widely used practice in modern agriculture because they generate conditions for optimal yield rates and quality. However, information about long-term effects of PC on soil quality parameters is scarce. The aim of this study is to compare the effect of three different mulching managements on soil quality parameters. Sampling and methodology: Three different managements were studied: Organic mulching (OM), 2-years PM and 4-years PM. Soil samples were collected from irrigated fields in 0-5, 5-10 and 10-30 cm depths and analyzed for water content (WC), pH, dissolved organic carbon (DOC), total soil carbon (Ctot) and cation exchange capacity (CECeff). Results and discussion: Mulching management has an influence on soil parameters. The magnitude of the effects is influenced by the type (organic agriculture practice vs. plastic mulching practice) and duration of the mulching. PM modified the water distribution through the soil column. WC values at the root zone were in average 10% higher compared to those measured at the topsoil. Under OM, the WC was lower than under PM. The pH was mainly influenced by the duration of the managements with slightly higher values after 4 than after 2-years PM. Under PM, aqueous extracts of the topsoil (0-5 cm depth) contained in average with 8.5±1.8 mg/L higher DOC than in 10-30 cm depth with 5.6±0.5 mg/L, which may indicate a mobilization of organic components in the upper layers. After 4-years PM, Ctot values were slightly higher than after 2-years PM and after OM. Surprisingly, after 4-years PM, CECeff values were with 138 - 157 mmolc/kg almost 2-fold higher than after 2-years PM and OM which had with 74 - 102 mmolc/kg comparable CECeff values. Long-term PM resulted in changes of soil pH and slightly increased Ctot which probably enhanced the CECeff of the soil. However, further investigations of the effect of PM on stability of soil organic matter and microbial community structure are needed.

Effects of water quality parameters on boron toxicity to Ceriodaphnia dubia.

PubMed

Dethloff, Gail M; Stubblefield, William A; Schlekat, Christian E

2009-07-01

The potential modifying effects of certain water quality parameters (e.g., hardness, alkalinity, pH) on the acute toxicity of boron were tested using a freshwater cladoceran, Ceriodaphnia dubia. By comparison, boron acute toxicity was less affected by water quality characteristics than some metals (e.g., copper and silver). Increases in alkalinity over the range tested did not alter toxicity. Increases in water hardness appeared to have an effect with very hard waters (>500 mg/L as CaCO(3)). Decreased pH had a limited influence on boron acute toxicity in laboratory waters. Increasing chloride concentration did not provide a protective effect. Boron acute toxicity was unaffected by sodium concentrations. Median acute lethal concentrations (LC(50)) in natural water samples collected from three field sites were all greater than in reconstituted laboratory waters that matched natural waters in all respects except for dissolved organic carbon. Water effect ratios in these waters ranged from 1.4 to 1.8. In subsequent studies using a commercially available source of natural organic matter, acute toxicity decreased with increased dissolved organic carbon, suggesting, along with the natural water studies, that dissolved organic carbon should be considered further as a modifier of boron toxicity in natural waters where it exceeds 2 mg/L.

Effects of chlorine and other water quality parameters on the release of silver nanoparticles from a ceramic surface.

PubMed

Bielefeldt, Angela R; Stewart, Michael W; Mansfield, Elisabeth; Scott Summers, R; Ryan, Joseph N

2013-08-01

A quartz crystal microbalance was used to determine the effects of different water quality parameters on the detachment of silver nanoparticles from surfaces representative of ceramic pot filters (CPFs). Silver nanoparticles stabilized with casein were used in the experiments. The average hydrodynamic diameter of the nanoparticles ranged from 20 nm to 100 nm over a pH range of 6.5-10.5. The isoelectric point was about 3.5 and the zeta potential was -45 mV from pH 4.5 to 9.5. The silver nanoparticles were deposited onto silica surfaces and a quartz crystal microbalance was used to monitor silver release from the surface. At environmentally relevant ranges of pH (4.8-9.3), ionic strength (0 and 150 mol/m(3) NaNO3 or 150 mol/m(3) Ca(NO3)2), and turbidity (0 and 51.5 NTU kaolin clay), the rates of silver release were similar. A high concentration of sodium chloride and bacteria (Echerichia coli in 10% tryptic soy broth) caused rapid silver release. Water containing sodium hypochlorite removed 85% of the silver from the silica surface within 3 h. The results suggest that contact between CPFs and prechlorinated water or bleach CPF cleaning should be avoided. Copyright © 2013 Elsevier Ltd. All rights reserved.

The quality of raw water for drinking water unit in Jakarta-Indonesia

NASA Astrophysics Data System (ADS)

Sidabutar, Noni Valeria; Hartono, Djoko M.; Soesilo, Tri Edhi Budhi; Hutapea, Reynold C.

2017-03-01

Water problems, i.e quality, quantity, continuity of clean water faced by the mostly urban area. Jakarta also faces similar issues, because the needs of society higher than the number of water fulfilled by the government. Moreover, Jakarta's water quality does not meet the standard set by the Government and heavily polluted by anthropogenic activities along its rivers. This research employs a quantitative research approach with the mix-method. It examines the raw water quality status for drinking water in West Tarum Canalin 2011-2015. The research results show water quality with this research, using water quality of with the water categorized as heavily-polluted category based on the Ministry of Environment's Decree No 115/2003 regarding the Guidelines for Determination of Water Quality Status. This present research also shown the water quality (parameters pH, temperature, Dissolved Oxygen (DO), Chemical Oxygen Demand (COD), and Biochemical Oxygen Demand (BOD)) from Jatiluhur Dam to the intake drinking water unit. In thirteen points of sampling also, the results obtained the parameters DO, COD, and BOD are fluctuating and exceed the standard.

Understanding the relationships among phytoplankton, benthic macroinvertebrates, and water quality variables in peri-urban river systems.

PubMed

Pinto, Uthpala; Maheshwari, Basant L; Morris, E Charles

2014-12-01

In this article, using the Hawkesbury-Nepean River as a case study, the spatial and temporal trends of water quality variables over three sampling surveys in a peri-urban situation are examined for their effect on benthic macroinvertebrate communities and phytoplankton communities and whether phytoplankton and benthic macroinvertebrate species can be used as indicators for river health assessment. For this, the authors monitored the spatial and temporal difference of 10 water quality parameters: temperature, turbidity, pH, dissolved oxygen, electrical conductivity, oxidation reduction potential, total nitrogen, total phosphorus, manganese, and suspended solids. The variability in water quality parameters clearly indicated a complex pattern, depending on the season (interaction p = 0.001), which highlighted how the river condition is stressed at multiple points as a result of anthropogenic effects. In particular, the downstream locations indicated an accumulation of nutrients, the presence of increased sediments, and phytoplankton related variables such as total counts, bio-volumes, chlorophyll-a, and total phosphorus. The patterns of phytoplankton communities varied in a complex way depending on the season (interaction p = 0.001). Abundances of phytoplankton were also found in low concentrations where the water column is not severely disturbed by flow and tide. However, when the water clarity drops resulting from tidal cycles, inflows from tributaries, and intense boating activities, the phytoplankton abundances also increased considerably. On the other hand, benthic macroinvertebrates compositions were significantly different between locations (p = 0.001) with increased abundances associated with upstream sites. Aphanocapsa holsatica and chironomid larvae appeared as the important indicators for upstream and downstream site differences in water quality. Water temperature influenced the phytoplankton community pattern (ρ(w) = 0.408), whereas pH influenced the benthic macroinvertebrate community pattern (ρ(w) = 0.437). The findings of this study provide valuable insights into the interactions of water quality parameters on biotic assemblages and to the extent that benthic macroinvertebrates and phytoplankton assemblages are suitable as indicators for monitoring and assessing peri-urban river health.

Tsukamoto fuzzy implementation to identify the pond water quality of koi

NASA Astrophysics Data System (ADS)

Qur'ania, A.; Verananda, D. I.

2017-01-01

The colour quality of koi was affected by the water quality in the pond. Koi fish have a diversity of types differentiated based on the body colour groups, such as one colour pattern, two colour patterns, three colours patterns and even more. Each colour characteristic of the koi have different handling, particularly in the handling of water quality, this is because the colour pigments in the body was affected by the composition of water quality include temperature, pH, TDS, do and salinity. The data of koi fish used were sanke, sowa, kohaku, shiro, yamabuki, ogon and chagoi. The aim of this study is to make an application to inform the condition of the pool water quality that can help breeders to know the water quality that will improve the handling strategies through water media. Tsukamoto Fuzzy method used to produce the three outputs namely water quality, water grade, and water conditions. The output of water quality consists of four categories, namely optimal, moderate, poor, and very poor. The output of water grade consists of grade A to D, while the output of water conditions consist of an excellent, good, bad, and very bad. Input to the application consists of five parameters, namely water temperature, pH, TDS, do and salinity.

Nutrient composition and technological quality of meat from alpacas reared in Peru.

PubMed

Salvá, Bettit K; Zumalacárregui, José M; Figueira, Ana C; Osorio, María T; Mateo, Javier

2009-08-01

The aim of this study was to increase the knowledge on alpaca meat quality characteristics. Twenty Huacaya breed alpacas, reared under a traditional unspecialized production system at the Andean region of Peru, were slaughtered at ages between 18 and 24months. Analyses were carried out on Longissimus thoracis and lumborum muscle (LTLM), unless otherwise specified. These included composition parameters: moisture, fat, protein, ash, minerals, amino acids, fatty acid profile (of both LTLM and perirenal fat), retinol and tocopherol concentrations and myoglobin and collagen contents. Other meat quality parameters were evaluated: pH, colour, water holding capacity and Warner-Bratzler shear-force. Alpaca LTLM was characterized by a low intramuscular fat content and mineral and amino acid compositions, polyunsaturated to saturated fatty acids ratio and conjugated linoleic acid content comparable to those found for beef and sheep meat. However, specifically, alpaca meat showed a relatively high n-6 to n-3 (3.7) ratio and low vitamin E concentration. Values of alpaca meat technological quality parameters were in the ranges reported for more conventional red meats, the exception being a lower b(∗) value.

Changes of physicochemical and microbiologicalparameters of infiltration water at Debina intake in Poznan, unique conditions - a flood

NASA Astrophysics Data System (ADS)

Kołaska, Sylwia; Jeż-Walkowiak, Joanna; Dymaczewski, Zbysław

2018-02-01

The paper presents characteristics of Debina infiltration intake which provides water for Poznan and neighbouring communes. The evaluation of effectiveness of infiltration process has been done based on the quality parameters of river water and infiltration water. The analysed water quality parameters are as follows: temperature, iron, manganese, DOCKMnO4, TOC, turbidity, colour, dissolved oxygen, free carbon dioxide, conductivity, total hardness, carbonate hardness, pH, heavy metals, detergents and microorganisms. The paper also includes an assessment of the impact of flood conditions on the quality of infiltration water and operation of infiltration intake. In this part of the paper the following parameters were taken into account: iron, manganese, DOCKMnO4, TOC, turbidity, colour, dissolved oxygen, free carbon dioxide, conductivity, total hardness, the total number of microorganisms in 36°C (mesophilic), the total number of microorganisms in 22°C (psychrophilic), coli bacteria, Clostridium perfringens, Escherichia coli, Enterococci. Analysis of the effects of flood on infiltration process leads to the following conclusions: the deterioration of infiltration water quality was due to the deterioration of river water quality, substantial shortening of groundwater passage and partial disappearance of the aeration zone. The observed deterioration of infiltration water quality did not affect the treated water quality, produced at water treatment plant.

Evaluation of water quality and stability in the drinking water distribution network in the Azogues city, Ecuador.

PubMed

García-Ávila, Fernando; Ramos-Fernández, Lía; Pauta, Damián; Quezada, Diego

2018-06-01

This document presents the physical-chemical parameters with the objective of evaluating and analyzing the drinking water quality in the Azogues city applying the water quality index (WQI) and to research the water stability in the distribution network using corrosion indexes. Thirty samples were collected monthly for six months throughout the drinking water distribution network; turbidity, temperature, electric conductivity, pH, total dissolved solids, total hardness, calcium, magnesium, alkalinity, chlorides, nitrates, sulfates and phosphates were determined; the physical-chemical parameters were measured using standard methods. The processed data revealed that the average values ​​of LSI, RSI and PSI were 0.5 (±0.34), 6.76 (±0.6), 6.50 (±0.99) respectively. The WQI calculation indicated that 100% of the samples are considered excellent quality water. According to the Langelier, Ryznar and Pukorius indexes showed that drinking water in Azogues is corrosive. The quality of drinking water according to the WQI is in a good and excellent category.

Genetic parameters for meat quality traits of Australian lamb meat.

PubMed

Mortimer, S I; van der Werf, J H J; Jacob, R H; Hopkins, D L; Pannier, L; Pearce, K L; Gardner, G E; Warner, R D; Geesink, G H; Edwards, J E Hocking; Ponnampalam, E N; Ball, A J; Gilmour, A R; Pethick, D W

2014-02-01

Genetic parameters were estimated for a range of meat quality traits recorded on Australian lamb meat. Data were collected from Merino and crossbred progeny of Merino, terminal and maternal meat breed sires of the Information Nucleus programme. Lambs born between 2007 and 2010 (n=8968) were slaughtered, these being the progeny of 372 sires and 5309 dams. Meat quality traits were found generally to be of moderate heritability (estimates between 0.15 and 0.30 for measures of meat tenderness, meat colour, polyunsaturated fat content, mineral content and muscle oxidative capacity), with notable exceptions of intramuscular fat (0.48), ultimate pH (0.08) and fresh meat colour a* (0.08) and b* (0.10) values. Genetic correlations between hot carcass weight and the meat quality traits were low. The genetic correlation between intramuscular fat and shear force was high (-0.62). Several measures of meat quality (fresh meat redness, retail meat redness, retail oxy/met value and iron content) appear to have potential for inclusion in meat sheep breeding objectives. © 2013.

Assessment of water quality index of bore well water samples from some selected locations of South Gujarat, India.

PubMed

Tripathi, S; Patel, H M; Srivastava, P K; Bafna, A M

2013-10-01

The present study calculates the water quality index (WQI) of some selected sites from South Gujarat (India) and assesses the impact of industries, agriculture and human activities. Chemical parameters were monitored for the calculation of WQI of some selected bore well samples. The results revealed that the WQI of the some bore well samples exceeded acceptable levels due to the dumping of wastes from municipal, industrial and domestic sources and agricultural runoff as well. Inverse Distance Weighting (IDW) was implemented for interpolation of each water quality parameter (pH, EC, alkalinity, total hardness, chloride, nitrate and sulphate) for the entire sampled area. The bore water is unsuitable for drinking and if the present state of affairs continues for long, it may soon become an ecologically dead bore.

Assessment of water quality from water harvesting using small farm reservoir for irrigation

NASA Astrophysics Data System (ADS)

Dewi, W. S.; Komariah; Samsuri, I. Y.; Senge, M.

2018-03-01

This study aims to assess the quality of rainfall-runoff water harvesting using small farm reservoir (SFR) for irrigation. Water quality assessment criteria based on RI Government Regulation number 82 the year 2001 on Water Quality Management and Pollution Control, and FAO Irrigation Water Quality Guidelines 1985. The experiment was conducted in the dry land of Wonosari Village, Gondangrejo District, Karanganyar Regency. SFR size was 10 m x 3 m x 2 m. Water quality measurements are done every week, ten times. Water samples were taken at 6 points, namely: distance of 2.5 m, 5 m, and 7.5 m from the inlet, at depth 25 cm and 175 cm from surface water. In each sampling point replicated three times. Water quality parameters include dissolved oxygen (DO), Turbidity (TSS), water pH, Nitrate (NO3), and Phosphate. The results show that water harvesting that collected in SFR meets both standards quality used, so the water is feasible for agricultural irrigation. The average value of harvested water was DO 2.6 mg/l, TSS 62.7 mg/l, pH 6.6, P 5.3 mg/l and NO3 0.16 mg/l. Rainfall-runoff water harvesting using SFR prospectus for increasing save water availability for irrigation.

Effect of long term chilled (up to 5weeks) then frozen (up to 12months) storage at two different sub-zero holding temperatures on beef: 1. Meat quality and microbial loads.

PubMed

Holman, Benjamin W B; Coombs, Cassius E O; Morris, Stephen; Kerr, Matthew J; Hopkins, David L

2017-11-01

Beef loins (LL) stored under different chilled-then-frozen storage combinations (up to 5 and 52weeks, respectively) and two frozen holding temperatures were evaluated for microbial load and meat quality parameters. We found holding temperature effects to be negligible, which suggest -12°C could deliver comparable quality LL to -18°C across these same storage periods. Meat quality parameters varied significantly, but when compared to existing consumer thresholds these may not be perceptible, colour being the exception which proved unacceptable, earlier into retail display when either chilled and subsequent frozen storage periods were increased. There was insufficient detection of key spoilage microbes to allow for statistical analysis, potentially due to the hygienic and commercially representative LL source, although variation in water activity, glycogen content, pH and other moisture parameters conducive to microbial proliferation were influenced by chilled-then-frozen storage. These outcomes could be applied to defining storage thresholds that assure beef quality within export networks, leveraging market access, and improving product management. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Effects of land cover, topography, and built structure on seasonal water quality at multiple spatial scales.

PubMed

Pratt, Bethany; Chang, Heejun

2012-03-30

The relationship among land cover, topography, built structure and stream water quality in the Portland Metro region of Oregon and Clark County, Washington areas, USA, is analyzed using ordinary least squares (OLS) and geographically weighted (GWR) multiple regression models. Two scales of analysis, a sectional watershed and a buffer, offered a local and a global investigation of the sources of stream pollutants. Model accuracy, measured by R(2) values, fluctuated according to the scale, season, and regression method used. While most wet season water quality parameters are associated with urban land covers, most dry season water quality parameters are related topographic features such as elevation and slope. GWR models, which take into consideration local relations of spatial autocorrelation, had stronger results than OLS regression models. In the multiple regression models, sectioned watershed results were consistently better than the sectioned buffer results, except for dry season pH and stream temperature parameters. This suggests that while riparian land cover does have an effect on water quality, a wider contributing area needs to be included in order to account for distant sources of pollutants. Copyright © 2012 Elsevier B.V. All rights reserved.

Environmental assessment of water and soil contamination in Rajakhali Canal of Karnaphuli River (Bangladesh) impacted by anthropogenic influences: a preliminary case study

NASA Astrophysics Data System (ADS)

Islam, M. Rafiqul; Das, N. G.; Barua, Prabal; Hossain, M. Belal; Venkatramanan, S.; Chung, S. Y.

2017-05-01

Soil and water quality determines the health of an aquatic ecosystem. Rajakhali Canal, a tributary of Karnaphuli River estuary, flowing through Chittagong City (the commercial capital of Bangladesh) receives a huge amount of domestic and industrial wastes and sewages. Monitoring the environmental status of Karnaphuli River and its tributaries is very important for their ecological and economical services provided to city areas. This study evaluated some environmental characteristics of water and soil in the Rajakhali Canal as it affected the environment, and ultimately the life and human beings of Chittagong City. The mean concentrations of physico-chemical parameters were pH (8.5), DO (0.1 mg/L), TA (47.6 mg/L), TDS (631.8 mg/L), TSS (280 mg/L), SO4-S (2.3 mg/L), NH3 (1.1 mg/L), NO3-N (0.2 mg/L) and PO4-P (0.1 mg/L) in the dry season. During the rainy season, the mean concentrations of physico-chemical parameters were pH (7.01), DO (0.55 mg/L), TA (65.9 mg/L), TDS (653.6 mg/L), TSS (300.3 mg/L), SO4-S (1 mg/L), NH3 - (0.6 mg/L), (NO3-N (0.3 mg/L) and PO4-P (0.5 mg/L) in water. In case of soil, the mean concentration of physico-chemical parameters in dry and rainy seasons was represented respectively as follows: pH (6.8), OM (4.5 %), sand (71.7 %), silt (3.1 %), clay (25.2 %), organic nitrogen (45.4 ppm) and phosphorus (9.6 ppm); and pH (6.7), OM (4.5 %), sand (74.4 %), silt (2.4 %), clay (23.2 %), organic nitrogen (35.3 ppm) and phosphorus (7.6 ppm). The result revealed that water and soil quality of this canal became deteriorated and that the total environment of the water body became polluted due to the anthropogenic activities such as industrial, domestic and irrigation effluents. Statistical analyses also supported that water and soil parameters were strongly correlated (1-tailed 0.05 level and 0.01 level significant) with each other at all stations during all seasons. The result of this study will be useful for management and planning for water quality monitoring in this estuary. To protect this vital estuarine region, the government agencies, private agencies and scientists should work with proper attention.

Updating national standards for drinking-water: a Philippine experience.

PubMed

Lomboy, M; Riego de Dios, J; Magtibay, B; Quizon, R; Molina, V; Fadrilan-Camacho, V; See, J; Enoveso, A; Barbosa, L; Agravante, A

2017-04-01

The latest version of the Philippine National Standards for Drinking-Water (PNSDW) was issued in 2007 by the Department of Health (DOH). Due to several issues and concerns, the DOH decided to make an update which is relevant and necessary to meet the needs of the stakeholders. As an output, the water quality parameters are now categorized into mandatory, primary, and secondary. The ten mandatory parameters are core parameters which all water service providers nationwide are obligated to test. These include thermotolerant coliforms or Escherichia coli, arsenic, cadmium, lead, nitrate, color, turbidity, pH, total dissolved solids, and disinfectant residual. The 55 primary parameters are site-specific and can be adopted as enforceable parameters when developing new water sources or when the existing source is at high risk of contamination. The 11 secondary parameters include operational parameters and those that affect the esthetic quality of drinking-water. In addition, the updated PNSDW include new sections: (1) reporting and interpretation of results and corrective actions; (2) emergency drinking-water parameters; (3) proposed Sustainable Development Goal parameters; and (4) standards for other drinking-water sources. The lessons learned and insights gained from the updating of standards are likewise incorporated in this paper.

Hyperspectral imaging technique for determination of pork freshness attributes

NASA Astrophysics Data System (ADS)

Li, Yongyu; Zhang, Leilei; Peng, Yankun; Tang, Xiuying; Chao, Kuanglin; Dhakal, Sagar

2011-06-01

Freshness of pork is an important quality attribute, which can vary greatly in storage and logistics. The specific objectives of this research were to develop a hyperspectral imaging system to predict pork freshness based on quality attributes such as total volatile basic-nitrogen (TVB-N), pH value and color parameters (L*,a*,b*). Pork samples were packed in seal plastic bags and then stored at 4°C. Every 12 hours. Hyperspectral scattering images were collected from the pork surface at the range of 400 nm to 1100 nm. Two different methods were performed to extract scattering feature spectra from the hyperspectral scattering images. First, the spectral scattering profiles at individual wavelengths were fitted accurately by a three-parameter Lorentzian distribution (LD) function; second, reflectance spectra were extracted from the scattering images. Partial Least Square Regression (PLSR) method was used to establish prediction models to predict pork freshness. The results showed that the PLSR models based on reflectance spectra was better than combinations of LD "parameter spectra" in prediction of TVB-N with a correlation coefficient (r) = 0.90, a standard error of prediction (SEP) = 7.80 mg/100g. Moreover, a prediction model for pork freshness was established by using a combination of TVB-N, pH and color parameters. It could give a good prediction results with r = 0.91 for pork freshness. The research demonstrated that hyperspectral scattering technique is a valid tool for real-time and nondestructive detection of pork freshness.

Monitoring muscle optical scattering properties during rigor mortis

NASA Astrophysics Data System (ADS)

Xia, J.; Ranasinghesagara, J.; Ku, C. W.; Yao, G.

2007-09-01

Sarcomere is the fundamental functional unit in skeletal muscle for force generation. In addition, sarcomere structure is also an important factor that affects the eating quality of muscle food, the meat. The sarcomere structure is altered significantly during rigor mortis, which is the critical stage involved in transforming muscle to meat. In this paper, we investigated optical scattering changes during the rigor process in Sternomandibularis muscles. The measured optical scattering parameters were analyzed along with the simultaneously measured passive tension, pH value, and histology analysis. We found that the temporal changes of optical scattering, passive tension, pH value and fiber microstructures were closely correlated during the rigor process. These results suggested that sarcomere structure changes during rigor mortis can be monitored and characterized by optical scattering, which may find practical applications in predicting meat quality.

Sperm motility in fishes. I. Effects of temperature and pH: a review.

PubMed

Alavi, Sayyed Mohammad Hadi; Cosson, Jacky

2005-02-01

Sperm motility is a key factor in allowing us to determine semen quality and fertilizing capacity. Motility in semen is mainly controlled by K+ in salmonids, and probably also in sturgeons, and by osmotic pressure in other freshwater and seawater fish species, but other factors, such as concentration of surrounding metabolites and ions (Ca2+, Mg2+, etc.), pH and temperature also influence motility characteristics. In the present study, we have mainly reviewed and summarized the effects of temperature and pH on the motility of spermatozoa in three fish species: salmonids, cyprinids and sturgeons. Data in the literature show that motility, fertilizing ability and velocity of spermatozoa, as well as the duration of the motility period, depend on the temperature of the assay medium and also of that of the brood fish holding tank. In contrast, the pH of the swimming medium, and thus the intracellular pH of spermatozoa, has less influence on sperm motility parameters in cyprinids, salmonids and sturgeons.

Stream water temperature limits occupancy of salamanders in mid-Atlantic protected areas

USGS Publications Warehouse

Grant, Evan H. Campbell; Wiewel, Amber N. M.; Rice, Karen C.

2014-01-01

Stream ecosystems are particularly sensitive to urbanization, and tolerance of water-quality parameters is likely important to population persistence of stream salamanders. Forecasted climate and landscape changes may lead to significant changes in stream flow, chemical composition, and temperatures in coming decades. Protected areas where landscape alterations are minimized will therefore become increasingly important for salamander populations. We surveyed 29 streams at three national parks in the highly urbanized greater metropolitan area of Washington, DC. We investigated relationships among water-quality variables and occupancy of three species of stream salamanders (Desmognathus fuscus, Eurycea bislineata, and Pseudotriton ruber). With the use of a set of site-occupancy models, and accounting for imperfect detection, we found that stream-water temperature limits salamander occupancy. There was substantial uncertainty about the effects of the other water-quality variables, although both specific conductance (SC) and pH were included in competitive models. Our estimates of occupancy suggest that temperature, SC, and pH have some importance in structuring stream salamander distribution.

The effect of anthropogenic activities to the decrease of water quality

NASA Astrophysics Data System (ADS)

Sidabutar, N. V.; Namara, I.; Hartono, D. M.; Soesilo, T. E. B.

2017-05-01

The raw water in Jakarta is supplied from Jatiluhur Dam, which is distributed pass through West Tarum Canal with an open canal about 70 km long. This water quality does not meet the standard set by the government and heavily polluted by anthropogenic activities along its river. This research uses a quantitative research approach with the mix-method. This research did an in-depth interview with inhabitants along the riverbank about their daily activity. The water along the riverbank is polluted by anthropogenic activities, such as: first: domestic activities (washing, cooking, and bathing), second: littering into the river, and third: discharging waste water from households into the river. This present research measures water quality for parameters pH, temperature, Dissolved Oxygen (DO), Chemical Oxygen Demand (COD), Total Dissolved Solid (TDS), Total Suspended Solid (TSS), and Fecal coliform. In this social segment, it is shown that pH, DO, TDS and Fecal coliformin the downstream part are worse than in the upstream.

Resistance and resilience of small-scale recirculating aquaculture systems (RAS) with or without algae to pH perturbation

PubMed Central

Giatsis, Christos; Md Yusoff, Fatimah; Verreth, Johan; Verdegem, Marc

2018-01-01

The experimental set-up of this study mimicked recirculating aquaculture systems (RAS) where water quality parameters such as dissolved oxygen, pH, temperature, and turbidity were controlled and wastes produced by fish and feeding were converted to inorganic forms. A key process in the RAS was the conversion of ammonia to nitrite and nitrite to nitrate through nitrification. It was hypothesized that algae inclusion in RAS would improve the ammonia removal from the water; thereby improving RAS water quality and stability. To test this hypothesis, the stability of the microbiota community composition in a freshwater RAS with (RAS+A) or without algae (RAS-A) was challenged by introducing an acute pH drop (from pH 7 to 4 during three hours) to the system. Stigeoclonium nanum, a periphytic freshwater microalga was used in this study. No significant effect of the algae presence was found on the resistance to the acute pH drop on ammonia conversion to nitrite and nitrite conversion to nitrate. Also the resilience of the ammonia conversion to the pH drop disruption was not affected by the addition of algae. This could be due to the low biomass of algae achieved in the RAS. However, with regard to the conversion step of nitrite to nitrate, RAS+A was significantly more resilient than RAS-A. In terms of overall bacterial communities, the composition and predictive function of the bacterial communities was significantly different between RAS+A and RAS-A. PMID:29659617

Quality by Design approach in the development of hydrophilic interaction liquid chromatographic method for the analysis of iohexol and its impurities.

PubMed

Jovanović, Marko; Rakić, Tijana; Tumpa, Anja; Jančić Stojanović, Biljana

2015-06-10

This study presents the development of hydrophilic interaction liquid chromatographic method for the analysis of iohexol, its endo-isomer and three impurities following Quality by Design (QbD) approach. The main objective of the method was to identify the conditions where adequate separation quality in minimal analysis duration could be achieved within a robust region that guarantees the stability of method performance. The relationship between critical process parameters (acetonitrile content in the mobile phase, pH of the water phase and ammonium acetate concentration in the water phase) and critical quality attributes is created applying design of experiments methodology. The defined mathematical models and Monte Carlo simulation are used to evaluate the risk of uncertainty in models prediction and incertitude in adjusting the process parameters and to identify the design space. The borders of the design space are experimentally verified and confirmed that the quality of the method is preserved in this region. Moreover, Plackett-Burman design is applied for experimental robustness testing and method is fully validated to verify the adequacy of selected optimal conditions: the analytical column ZIC HILIC (100 mm × 4.6 mm, 5 μm particle size); mobile phase consisted of acetonitrile-water phase (72 mM ammonium acetate, pH adjusted to 6.5 with glacial acetic acid) (86.7:13.3) v/v; column temperature 25 °C, mobile phase flow rate 1 mL min(-1), wavelength of detection 254 nm. Copyright © 2015 Elsevier B.V. All rights reserved.

Effects of urbanization on stream water quality in the city of Atlanta, Georgia, USA

USGS Publications Warehouse

Peters, N.E.

2009-01-01

A long-term stream water quality monitoring network was established in the city of Atlanta, Georgia during 2003 to assess baseline water quality conditions and the effects of urbanization on stream water quality. Routine hydrologically based manual stream sampling, including several concurrent manual point and equal width increment sampling, was conducted ???12 times annually at 21 stations, with drainage areas ranging from 3.7 to 232 km2. Eleven of the stations are real-time (RT) stations having continuous measures of stream stage/ discharge, pH, dissolved oxygen, specific conductance, water temperature and turbidity, and automatic samplers for stormwater collection. Samples were analyzed for field parameters, and a broad suite of water quality and sediment-related constituents. Field parameters and concentrations of major ions, metals, nutrient species and coliform bacteria among stations were evaluated and with respect to watershed characteristics and plausible sources from 2003 through September 2007. Most constituent concentrations are much higher than nearby reference streams. Concentrations are statistically different among stations for several constituents, despite high variability both within and among stations. Routine manual sampling, automatic sampling during stormflows and RT water quality monitoring provided sufficient information about urban stream water quality variability to evaluate causes of water quality differences among streams. Fecal coliform bacteria concentrations of most samples exceeded Georgia's water quality standard for any water-usage class. High chloride concentrations occur at three stations and are hypothesized to be associated with discharges of chlorinated combined sewer overflows, drainage of swimming pool(s) and dissolution and transport during rainstorms of CaCl2, a deicing salt applied to roads during winter storms. One stream was affected by dissolution and transport of ammonium alum [NH4Al(SO4)2] from an alum-manufacturing plant; streamwater has low pH (<5), low alkalinity and high metals concentrations. Several trace metals exceed acute and chronic water quality standards and high concentrations are attributed to washoff from impervious surfaces.

Study of Material Used in Nanotechnology for the Recycling of Industrial Waste Water

NASA Astrophysics Data System (ADS)

Larbi, L.; Fertikh, N.; Toubal, A.

The objective of our study is to recycle the industrial waste water of a industrial Complex after treatment by the bioprocess MBR (membrane bioreactor). In order to apply this bioprocess, the water quality in question was first of all studied. To characterize this industrial waste water, a series of physicochemical analysis was carried out according to standardized directives and methods. Following-up the water quality to meet the regulatory requirements with rejection of this industrial waste water, a study was done thanks to the permanently monitoring of the following relevant parameters(P): the flow, the potential of hydrogen (pH), the total suspended solids(TSS), the turbidity (Turb), the chemical oxygen demand (COD),the biochemical oxygen demand (BOD), the Kjeldahl total nitrogen (KTN) and ammonia (NH4+), the total phosphorus (Ptot), the fluorine (F), the oils (O), the fats (F) and the phenols (Ph). According to collected information, it was established the sampling rates to which the quality control was done, the selected analytical methods were validated by the control charts and the analysis test number was determined by the Cochran test. The results of the quality control show that some rejected water contents are not in the Algerian standards, but, in our case, the objective is the preoccupation for a standard setting of these industrial water parameters so as to recycle it. The process adopted by MBR for waste water treatment is being studied, first in the development of the experimental characterizing of the reactor and the selected membrane.

A water quality index model using stepwise regression and neural networks models for the Piabanha River basin in Rio de Janeiro, Brazil

NASA Astrophysics Data System (ADS)

Villas Boas, M. D.; Olivera, F.; Azevedo, J. S.

2013-12-01

The evaluation of water quality through 'indexes' is widely used in environmental sciences. There are a number of methods available for calculating water quality indexes (WQI), usually based on site-specific parameters. In Brazil, WQI were initially used in the 1970s and were adapted from the methodology developed in association with the National Science Foundation (Brown et al, 1970). Specifically, the WQI 'IQA/SCQA', developed by the Institute of Water Management of Minas Gerais (IGAM), is estimated based on nine parameters: Temperature Range, Biochemical Oxygen Demand, Fecal Coliforms, Nitrate, Phosphate, Turbidity, Dissolved Oxygen, pH and Electrical Conductivity. The goal of this study was to develop a model for calculating the IQA/SCQA, for the Piabanha River basin in the State of Rio de Janeiro (Brazil), using only the parameters measurable by a Multiparameter Water Quality Sonde (MWQS) available in the study area. These parameters are: Dissolved Oxygen, pH and Electrical Conductivity. The use of this model will allow to further the water quality monitoring network in the basin, without requiring significant increases of resources. The water quality measurement with MWQS is less expensive than the laboratory analysis required for the other parameters. The water quality data used in the study were obtained by the Geological Survey of Brazil in partnership with other public institutions (i.e. universities and environmental institutes) as part of the project "Integrated Studies in Experimental and Representative Watersheds". Two models were developed to correlate the values of the three measured parameters and the IQA/SCQA values calculated based on all nine parameters. The results were evaluated according to the following validation statistics: coefficient of determination (R2), Root Mean Square Error (RMSE), Akaike information criterion (AIC) and Final Prediction Error (FPE). The first model was a linear stepwise regression between three independent variables (input) and one dependent variable (output) to establish an equation relating input to output. This model produced the following statistics: R2 = 0.85, RMSE = 6.19, AIC =0.65 and FPE = 1.93. The second model was a Feedforward Neural Network with one tan-sigmoid hidden layer (4 neurons) and one linear output layer. The neural network was trained based on a backpropagation algorithm using the input as predictors and the output as target. The following statistics were found: R2 = 0.95, RMSE = 4.86, AIC= 0.33 and FPE = 1.39. The second model produced a better fit than the first one, having a greater R2 and smaller RMSE, AIC and FPE. The best performance of the second method can be attributed to the fact that the water quality parameters often exhibit nonlinear behaviors and neural networks are capable of representing nonlinear relationship efficiently, while the regression is limited to linear relationships. References: Brown, R.M., McLelland, N.I., Deininger, R.A., Tozer, R.G.1970. A Water Quality Index-Do we dare? Water & Sewage Works, October: 339-343.

Process development for robust removal of aggregates using cation exchange chromatography in monoclonal antibody purification with implementation of quality by design.

PubMed

Xu, Zhihao; Li, Jason; Zhou, Joe X

2012-01-01

Aggregate removal is one of the most important aspects in monoclonal antibody (mAb) purification. Cation-exchange chromatography (CEX), a widely used polishing step in mAb purification, is able to clear both process-related impurities and product-related impurities. In this study, with the implementation of quality by design (QbD), a process development approach for robust removal of aggregates using CEX is described. First, resin screening studies were performed and a suitable CEX resin was chosen because of its relatively better selectivity and higher dynamic binding capacity. Second, a pH-conductivity hybrid gradient elution method for the CEX was established, and the risk assessment for the process was carried out. Third, a process characterization study was used to evaluate the impact of the potentially important process parameters on the process performance with respect to aggregate removal. Accordingly, a process design space was established. Aggregate level in load is the critical parameter. Its operating range is set at 0-3% and the acceptable range is set at 0-5%. Equilibration buffer is the key parameter. Its operating range is set at 40 ± 5 mM acetate, pH 5.0 ± 0.1, and acceptable range is set at 40 ± 10 mM acetate, pH 5.0 ± 0.2. Elution buffer, load mass, and gradient elution volume are non-key parameters; their operating ranges and acceptable ranges are equally set at 250 ± 10 mM acetate, pH 6.0 ± 0.2, 45 ± 10 g/L resin, and 10 ± 20% CV respectively. Finally, the process was scaled up 80 times and the impurities removal profiles were revealed. Three scaled-up runs showed that the size-exclusion chromatography (SEC) purity of the CEX pool was 99.8% or above and the step yield was above 92%, thereby proving that the process is both consistent and robust.

Honey collected from different floras of Chandigarh Tricity: a comparative study involving physicochemical parameters and biochemical activities.

PubMed

Kumar, Pradeep; Sindhu, Rakesh K; Narayan, Shridhar; Singh, Inderbir

2010-12-01

Different monofloral honeys have a distinctive flavor and color because of differences in physicochemical parameters because of their principal nectar sources or floral types. Honey samples were collected from Apis mellifera colonies forged on 10 floras to analyze the quality of honey in terms of standards laid by Honey Grading and Marking Rules (HGMR), India, 2008 and Codex Alimentarious Commission (CAC), 1969 . The honey samples were analyzed for various physicochemical parameters of honey quality control, i.e., pH, total acidity, moisture, reducing sugars, non-reducing sugars, total sugars, water insoluble solids (WIS), ash content, 5-hydroxymethylfurfural content, and diastase value. The antioxidant potential was estimated using Folin-Ciocalteu reagent. Further, honey samples were assayed for antibacterial activities against clinical isolates of Staphylococcus aureus and Escherichia coli using the hole-plate diffusion method. The physicochemical variation in the composition of honey because of floral source shows Ziziphus honey with high pH and diastase values along with low acidity, whereas Helianthus honey contained high reducing sugar and low moisture content. Amomum, Brassica, Acacia, and Citrus contained lowest amount of non-reducing sugars, ash, WIS, and moisture, respectively. Lowest 5-hydroxymethylfurfural (HMF) value was detected in Amomum honey, while highest HMF value was observed with Eucalyptus. The maximum antibacterial and antioxidant potential was observed in Azadirachta and Citrus, respectively. The quality of honey produced by local beekeepers met HGMR and CAC standards, and the chemical composition and biological properties of honey were dependent on the floral source from which it was produced.

Utilization of municipal wastewater for cooling in thermoelectric power plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Safari, Iman; Walker, Michael E.; Hsieh, Ming-Kai

2013-09-01

A process simulation model has been developed using Aspen Plus® with the OLI (OLI System, Inc.) water chemistry model to predict water quality in the recirculating cooling loop utilizing secondary- and tertiary-treated municipal wastewater as the source of makeup water. Simulation results were compared with pilot-scale experimental data on makeup water alkalinity, loop pH, and ammonia evaporation. The effects of various parameters including makeup water quality, salt formation, NH 3 and CO 2 evaporation mass transfer coefficients, heat load, and operating temperatures were investigated. The results indicate that, although the simulation model can capture the general trends in the loopmore » pH, experimental data on the rates of salt precipitation in the system are needed for more accurate prediction of the loop pH. It was also found that stripping of ammonia and carbon dioxide in the cooling tower can influence the cooling loop pH significantly. The effects of the NH 3 mass transfer coefficient on cooling loop pH appear to be more significant at lower values (e.g., k NH3 < 4×10 -3 m/s) when the makeup water alkalinity is low (e.g., <90 mg/L as CaCO 3). The effect of the CO2 mass transfer coefficient was found to be significant only at lower alkalinity values (e.g., k CO2<4×10 -6 m/s).« less

Genetic parameters of product quality and hepatic metabolism in fattened mule ducks.

PubMed

Marie-Etancelin, C; Basso, B; Davail, S; Gontier, K; Fernandez, X; Vitezica, Z G; Bastianelli, D; Baéza, E; Bernadet, M-D; Guy, G; Brun, J-M; Legarra, A

2011-03-01

Genetic parameters of traits related to hepatic lipid metabolism, carcass composition, and product quality of overfed mule ducks were estimated on both parental lines of this hybrid: the common duck line for the maternal side and the Muscovy line for the paternal side. The originality of the statistical model was to include simultaneously the additive genetic effect of the common ducks and that of the Muscovy ducks, revealing a greater genetic determinism in common than in Muscovy. Plasma metabolic indicators (glucose, triglyceride, and cholesterol contents) were heritable, in particular at the end of the overfeeding period, and heritabilities increased with the overfeeding stage. Carcass composition traits were highly heritable in the common line, with values ranging from 0.15 for liver weight, 0.21 for carcass weight, and 0.25 for abdominal fat weight to 0.32 for breast muscle weight. Heritabilities of technological outputs were greater for the fatty liver (0.19 and 0.08, respectively, on common and Muscovy sides for liver melting rate) than for the pectoralis major muscle (between 0.02 and 0.05 on both parental sides for cooking losses). Fortunately, the processing industry is mainly facing problems in liver quality, such as too high of a melting rate, than in meat quality. The meat quality appraisal criteria (such as texture and cooking losses), usually dependent on pH and the rate of decline of pH, were also very lowly heritable. This study demonstrated that genetic determinism of meat quality and ability of overfeeding is not similar in the common population and in the Muscovy population; traits related to fattening, muscle development, and BW have heritability values from 2 to 4 times greater on the common line than on the Muscovy line, which is relevant for considering different selection strategies.

Assessing the efficacy of immunotherapy with a glutaraldehyde-modified house dust mite extract in children by monitoring changes in clinical parameters and inflammatory markers in exhaled breath.

PubMed

Lozano, Jaime; Cruz, María-Jesús; Piquer, Mónica; Giner, Maria-Teresa; Plaza, Ana María

2014-01-01

The aim of this study was to evaluate the effectiveness of specific immunotherapy (SIT) management with allergoids in children with allergic asthma by monitoring changes in clinical parameters and inflammatory markers in exhaled breath. The study population included 43 patients (24 males) of 6-14 years of age, who had allergic asthma and were sensitized to mites. Twenty-three individuals were treated with subcutaneous SIT (PURETHAL® Mites, HAL Allergy) for 8 months, i.e. the SIT group, and 20 were given medication to treat symptoms only, i.e. the control group. Before treatment and after 4 and 8 months, several clinical parameters, the levels of exhaled nitric oxide and the pH of exhaled breath condensate (EBC) were determined. The SIT group presented with an improvement in asthma classification, a reduction in maintenance drug therapy and improved scores on the quality-of-life questionnaire. These changes were not observed in the control group. Both groups presented significant decreases in EBC pH values at 4 and 8 months after treatment compared to at baseline. However, analysis of the variable 'ratio' showed an increase in the EBC pH values after 8 months of treatment in the SIT group compared with the values at 4 months. SIT with standardized mite extract reduces asthma symptoms in children. A decrease in EBC pH values was observed in both groups, although the SIT group presented a tendency of recovered values after 8 months. Future studies of EBC pH monitoring in the longer term are needed to determine the effectiveness of this marker. © 2014 S. Karger AG, Basel.

Impact of pH on Urine Chemistry Assayed on Roche Analyzers.

PubMed

Cohen, R; Alkouri, R; Tostivint, I; Djiavoudine, S; Mestari, F; Dever, S; Atlan, G; Devilliers, C; Imbert-Bismut, F; Bonnefont-Rousselot, D; Monneret, D

2017-10-01

The pH may impact the concentration of certain urinary parameters, making urine pre-treatment questionable. 1) Determining the impact of pH in vitro on the urinary concentration of chemistry parameters assayed on Roche Modular analyzers. 2) Evaluating whether concentrations depended on pH in non-pretreated urines from patients. 1) The optimal urinary pH values for each measurement were: 6.3 ± 0.8 (amylase), < 5.5 (calcium and magnesium), < 6.5 (phosphorus), > 6.5 (uric acid). Urinary creatinine, sodium and urea concentrations were not pH-dependent. 2) In urines from patients, the pH was negatively associated with the concentration of some urinary parameters. However, concentrations of all the parameters were strongly and positively correlated with urinary creatinine, and relationships with pH were no longer evidenced after creatinine-normalization. The need for urine pH adjustment does not seem necessary when considering renal function. However, from an analytical and accreditation standpoint, the relationship between urine pH and several parameters justifies its measurement.

Assessment and modeling of groundwater quality using WQI and GIS in Upper Egypt area.

PubMed

Rabeiy, Ragab ElSayed

2017-04-04

The continuous growth and development of population need more fresh water for drinking, irrigation, and domestic in arid countries like Egypt. Evaluation the quality of groundwater is an essential study to ensure its suitability for different purposes. In this study, 812 groundwater samples were taken within the middle area of Upper Egypt (Sohag Governorate) to assess the quality of groundwater for drinking and irrigation purposes. Eleven water parameters were analyzed at each groundwater sample (Na + , K + , Ca 2+ , Mg 2+ , HCO 3 - SO 4 2- , Fe 2+ , Mn 2+ , Cl - , electrical conductivity, and pH) to exploit them in water quality evaluation. A classical statistics were applied for the raw data to examine the distribution of physicochemical parameters in the investigated area. The relationship between groundwater parameters was tested using the correlation coefficient where a strong relationship was found between several water parameters such as Ca 2+ and Cl - . Water quality index (WQI) is a mathematical model used to transform many water parameters into a single indicator value which represents the water quality level. Results of WQI showed that 20% of groundwater samples are excellent, 75% are good for drinking, and 7% are very poor water while only 1% of samples are unsuitable for drinking. To test the suitability of groundwater for irrigation, three indices are used; they are sodium adsorption ration (SAR), sodium percentage (Na%), and permeability index (PI). For irrigation suitability, the study proved that most sampling sites are suitable while less than 3% are unsuitable for irrigation. The spatial distribution of the estimated values of WQI, SAR, Na%, PI, and each groundwater parameter was spatially modeled using GIS.

A systematic approach to evaluate parameter consistency in the inlet stream of source separated biowaste composting facilities: A case study in Colombia.

PubMed

Oviedo-Ocaña, E R; Torres-Lozada, P; Marmolejo-Rebellon, L F; Torres-López, W A; Dominguez, I; Komilis, D; Sánchez, A

2017-04-01

Biowaste is commonly the largest fraction of municipal solid waste (MSW) in developing countries. Although composting is an effective method to treat source separated biowaste (SSB), there are certain limitations in terms of operation, partly due to insufficient control to the variability of SSB quality, which affects process kinetics and product quality. This study assesses the variability of the SSB physicochemical quality in a composting facility located in a small town of Colombia, in which SSB collection was performed twice a week. Likewise, the influence of the SSB physicochemical variability on the variability of compost parameters was assessed. Parametric and non-parametric tests (i.e. Student's t-test and the Mann-Whitney test) showed no significant differences in the quality parameters of SSB among collection days, and therefore, it was unnecessary to establish specific operation and maintenance regulations for each collection day. Significant variability was found in eight of the twelve quality parameters analyzed in the inlet stream, with corresponding coefficients of variation (CV) higher than 23%. The CVs for the eight parameters analyzed in the final compost (i.e. pH, moisture, total organic carbon, total nitrogen, C/N ratio, total phosphorus, total potassium and ash) ranged from 9.6% to 49.4%, with significant variations in five of those parameters (CV>20%). The above indicate that variability in the inlet stream can affect the variability of the end-product. Results suggest the need to consider variability of the inlet stream in the performance of composting facilities to achieve a compost of consistent quality. Copyright © 2017 Elsevier Ltd. All rights reserved.

Portable Electronic Tongue Based on Microsensors for the Analysis of Cava Wines.

PubMed

Giménez-Gómez, Pablo; Escudé-Pujol, Roger; Capdevila, Fina; Puig-Pujol, Anna; Jiménez-Jorquera, Cecilia; Gutiérrez-Capitán, Manuel

2016-10-27

Cava is a quality sparkling wine produced in Spain. As a product with a designation of origin, Cava wine has to meet certain quality requirements throughout its production process; therefore, the analysis of several parameters is of great interest. In this work, a portable electronic tongue for the analysis of Cava wine is described. The system is comprised of compact and low-power-consumption electronic equipment and an array of microsensors formed by six ion-selective field effect transistors sensitive to pH, Na⁺, K⁺, Ca 2+ , Cl - , and CO₃ 2- , one conductivity sensor, one redox potential sensor, and two amperometric gold microelectrodes. This system, combined with chemometric tools, has been applied to the analysis of 78 Cava wine samples. Results demonstrate that the electronic tongue is able to classify the samples according to the aging time, with a percentage of correct prediction between 80% and 96%, by using linear discriminant analysis, as well as to quantify the total acidity, pH, volumetric alcoholic degree, potassium, conductivity, glycerol, and methanol parameters, with mean relative errors between 2.3% and 6.0%, by using partial least squares regressions.

Portable Electronic Tongue Based on Microsensors for the Analysis of Cava Wines

PubMed Central

Giménez-Gómez, Pablo; Escudé-Pujol, Roger; Capdevila, Fina; Puig-Pujol, Anna; Jiménez-Jorquera, Cecilia; Gutiérrez-Capitán, Manuel

2016-01-01

Cava is a quality sparkling wine produced in Spain. As a product with a designation of origin, Cava wine has to meet certain quality requirements throughout its production process; therefore, the analysis of several parameters is of great interest. In this work, a portable electronic tongue for the analysis of Cava wine is described. The system is comprised of compact and low-power-consumption electronic equipment and an array of microsensors formed by six ion-selective field effect transistors sensitive to pH, Na+, K+, Ca2+, Cl−, and CO32−, one conductivity sensor, one redox potential sensor, and two amperometric gold microelectrodes. This system, combined with chemometric tools, has been applied to the analysis of 78 Cava wine samples. Results demonstrate that the electronic tongue is able to classify the samples according to the aging time, with a percentage of correct prediction between 80% and 96%, by using linear discriminant analysis, as well as to quantify the total acidity, pH, volumetric alcoholic degree, potassium, conductivity, glycerol, and methanol parameters, with mean relative errors between 2.3% and 6.0%, by using partial least squares regressions. PMID:27801796

Impact of city effluents on water quality of Indus River: assessment of temporal and spatial variations in the southern region of Khyber Pakhtunkhwa, Pakistan.

PubMed

Khan, Ilham; Khan, Azim; Khan, Muhammad Sohail; Zafar, Shabnam; Hameed, Asma; Badshah, Shakeel; Rehman, Shafiq Ur; Ullah, Hidayat; Yasmeen, Ghazala

2018-04-04

The impact of city effluents on water quality of Indus River was assessed in the southern region of Khyber Pakhtunkhwa, Pakistan. Water samples were collected in dry (DS) and wet (WS) seasons from seven sampling zones along Indus River and the physical, bacteriological, and chemical parameters determining water quality were quantified. There were marked temporal and spatial variations in the water quality of Indus River. The magnitude of pollution was high in WS compared with DS. The quality of water varied across the sampling zones, and it greatly depended upon the nature of effluents entering the river. Water samples exceeded the WHO permissible limits for pH, EC, TDS, TS, TSS, TH, DO, BOD, COD, total coliforms, Escherichia coli, Ca 2+ , Mg 2+ , NO 3 - , and PO 4 2- . Piper analysis indicated that water across the seven sampling zones along Indus River was alkaline in nature. Correlation analyses indicated that EC, TDS, TS, TH, DO, BOD, and COD may be considered as key physical parameters, while Na + , K + , Ca 2+ , Mg 2+ , Cl - , F - , NO 3 - , PO 4 2- , and SO 4 2- as key chemical parameters determining water quality, because they were strongly correlated (r > 0.70) with most of the parameters studied. Cluster analysis indicated that discharge point at Shami Road is the major source of pollution impairing water quality of Indus River. Wastewater treatment plants must be installed at all discharge points along Indus River for protecting the quality of water of this rich freshwater resource in Pakistan.

Toxicity of cadmium to goldfish, Carassius auratus, in hard, and soft water

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCarty, L.S.; Henry, J.A.C.; Houston, A.H.

1978-01-01

Variations in cadmium form and concentration and in selected water quality parameters (pH, dissolved oxygen, total hardness, total alkalinity, conductivity) were monitored during static bioassays conducted with relatively soft (approximately 20 mg/L as CaCO/sub 3/) and hard (approximately 140 mg/L as CaCO/sub 3/) waters. Cadmium concentrations were reasonably stable in soft water, and with the exception of total hardness, water quality was not greatly altered during assay. Cumulative mortality curves were of a simple sigmoidal type and readily analyzed by conventional procedures. LC50 values of 2.76, 2.13, and 1.78 mg Cd/L were estimated on the basis of 48-, 96-, andmore » 240-h periods of observation. During hard-water trials there were transient increases in the amount of particulate cadmium present and sharp decreases in total cadmium levels. Several parameters (pH, total alkalinity, conductivity) exhibited transient and/or sustained variations of a cadmium concentration-dependent type. Mortality curves were typically biphasic. The extent of first-phase mortality was significantly correlated with the magnitude of the initial pH decline and the amount of cadmium present in centrifugable form. Conventional procedures did not result in rectification of 240-h cumulative mortality curves, and the 240-h LC50 value (40.2 mg Cd/L) is considered to be inherently less precise than those obtained on the basis of 48- and 96-h periods of observation (46.9, 46.8 mg Cd/L).« less

Application of Analytical Quality by Design concept for bilastine and its degradation impurities determination by hydrophilic interaction liquid chromatographic method.

PubMed

Terzić, Jelena; Popović, Igor; Stajić, Ana; Tumpa, Anja; Jančić-Stojanović, Biljana

2016-06-05

This paper deals with the development of hydrophilic interaction liquid chromatographic (HILIC) method for the analysis of bilastine and its degradation impurities following Analytical Quality by Design approach. It is the first time that the method for bilastine and its impurities is proposed. The main objective was to identify the conditions where an adequate separation in minimal analysis duration could be achieved within a robust region. Critical process parameters which have the most influence on method performance were defined as acetonitrile content in the mobile phase, pH of the aqueous phase and ammonium acetate concentration in the aqueous phase. Box-Behnken design was applied for establishing a relationship between critical process parameters and critical quality attributes. The defined mathematical models and Monte Carlo simulations were used to identify the design space. Fractional factorial design was applied for experimental robustness testing and the method is validated to verify the adequacy of selected optimal conditions: the analytical column Luna(®) HILIC (100mm×4.6mm, 5μm particle size); mobile phase consisted of acetonitrile-aqueous phase (50mM ammonium acetate, pH adjusted to 5.3 with glacial acetic acid) (90.5:9.5, v/v); column temperature 30°C, mobile phase flow rate 1mLmin(-1), wavelength of detection 275nm. Copyright © 2016 Elsevier B.V. All rights reserved.

Predicting Trihalomethanes (THMs) in the New York City Water Supply

NASA Astrophysics Data System (ADS)

Mukundan, R.; Van Dreason, R.

2013-12-01

Chlorine, a commonly used disinfectant in most water supply systems, can combine with organic carbon to form disinfectant byproducts including carcinogenic trihalomethanes (THMs). We used water quality data from 24 monitoring sites within the New York City (NYC) water supply distribution system, measured between January 2009 and April 2012, to develop site-specific empirical models for predicting total trihalomethane (TTHM) levels. Terms in the model included various combinations of the following water quality parameters: total organic carbon, pH, specific conductivity, and water temperature. Reasonable estimates of TTHM levels were achieved with overall R2 of about 0.87 and predicted values within 5 μg/L of measured values. The relative importance of factors affecting TTHM formation was estimated by ranking the model regression coefficients. Site-specific models showed improved model performance statistics compared to a single model for the entire system most likely because the single model did not consider locational differences in the water treatment process. Although never out of compliance in 2011, the TTHM levels in the water supply increased following tropical storms Irene and Lee with 45% of the samples exceeding the 80 μg/L Maximum Contaminant Level (MCL) in October and November. This increase was explained by changes in water quality parameters, particularly by the increase in total organic carbon concentration and pH during this period.

Iron and manganese removal: Recent advances in modelling treatment efficiency by rapid sand filtration.

PubMed

Vries, D; Bertelkamp, C; Schoonenberg Kegel, F; Hofs, B; Dusseldorp, J; Bruins, J H; de Vet, W; van den Akker, B

2017-02-01

A model has been developed that takes into account the main characteristics of (submerged) rapid filtration: the water quality parameters of the influent water, notably pH, iron(II) and manganese(II) concentrations, homogeneous oxidation in the supernatant layer, surface sorption and heterogeneous oxidation kinetics in the filter, and filter media adsorption characteristics. Simplifying assumptions are made to enable validation in practice, while maintaining the main mechanisms involved in iron(II) and manganese(II) removal. Adsorption isotherm data collected from different Dutch treatment sites show that Fe(II)/Mn(II) adsorption may vary substantially between them, but generally increases with higher pH. The model is sensitive to (experimentally) determined adsorption parameters and the heterogeneous oxidation rate. Model results coincide with experimental values when the heterogeneous rate constants are calibrated. Copyright © 2016 Elsevier Ltd. All rights reserved.

Groundwater quality assessment of urban Bengaluru using multivariate statistical techniques

NASA Astrophysics Data System (ADS)

Gulgundi, Mohammad Shahid; Shetty, Amba

2018-03-01

Groundwater quality deterioration due to anthropogenic activities has become a subject of prime concern. The objective of the study was to assess the spatial and temporal variations in groundwater quality and to identify the sources in the western half of the Bengaluru city using multivariate statistical techniques. Water quality index rating was calculated for pre and post monsoon seasons to quantify overall water quality for human consumption. The post-monsoon samples show signs of poor quality in drinking purpose compared to pre-monsoon. Cluster analysis (CA), principal component analysis (PCA) and discriminant analysis (DA) were applied to the groundwater quality data measured on 14 parameters from 67 sites distributed across the city. Hierarchical cluster analysis (CA) grouped the 67 sampling stations into two groups, cluster 1 having high pollution and cluster 2 having lesser pollution. Discriminant analysis (DA) was applied to delineate the most meaningful parameters accounting for temporal and spatial variations in groundwater quality of the study area. Temporal DA identified pH as the most important parameter, which discriminates between water quality in the pre-monsoon and post-monsoon seasons and accounts for 72% seasonal assignation of cases. Spatial DA identified Mg, Cl and NO3 as the three most important parameters discriminating between two clusters and accounting for 89% spatial assignation of cases. Principal component analysis was applied to the dataset obtained from the two clusters, which evolved three factors in each cluster, explaining 85.4 and 84% of the total variance, respectively. Varifactors obtained from principal component analysis showed that groundwater quality variation is mainly explained by dissolution of minerals from rock water interactions in the aquifer, effect of anthropogenic activities and ion exchange processes in water.

Assessment of Groundwater quality in Krishnagiri and Vellore Districts in Tamil Nadu, India

NASA Astrophysics Data System (ADS)

Shanmugasundharam, A.; Kalpana, G.; Mahapatra, S. R.; Sudharson, E. R.; Jayaprakash, M.

2017-07-01

Groundwater quality is important as it is the main factor determining its suitability for drinking, domestic, agricultural and industrial purposes. The suitability of groundwater for drinking and irrigation has been assessed in north and eastern part of Krishnagiri district, South-western part of Vellore district and contiguous with Andhra Pradesh states, India. A total of 31 groundwater samples were collected in the study area. The groundwater quality assessment has been carried out by evaluating the physicochemical parameters such as pH, EC, TDS, {HCO}3^{ - }, Cl-, {SO}4^{2 - }, Ca2+, Mg2+, Na+ and K+. The dominant cations are in the order of Na+ > K+ > Ca2+ > Mg2+ while the dominant anions have the trends of Cl- > {HCO}3^{ - } > {SO}4^{2 - } > CO3. The quality of the water is evaluated using Wilcox diagram and the results reveals that most of the samples are found to be suitable for irrigation. Based on these parameters, groundwater has been assessed in favor of its suitability for drinking and irrigation purpose.

Investigation of product quality between extemporaneously compounded progesterone vaginal suppositories and an approved progesterone vaginal gel.

PubMed

Mahaguna, Vorapann; McDermott, J Mario; Zhang, Feng; Ochoa, Felipe

2004-01-01

The purpose of this investigation was to compare quality parameters, including product appearance, content uniformity, pH, weight uniformity, microbial limit testing and preservative effectiveness testing on extemporaneously compounded progesterone vaginal suppositories obtained from 10 randomly chosen compounding pharmacies (90 suppositories each) across the United States, to the Food and Drug Administration (FDA) approved prescription progesterone gel product (Prochieve/Crinone) which is manufactured in a cGMP regulated facility. The content uniformity and pH were determined using qualified methods. The microbial limits testing and preservative effectiveness testing were conducted according to compendial methods. Only one pharmacy provided suppositories that were all within the potency limits required for the prescription progesterone gel product. The other pharmacies provided at least some suppositories where progesterone content was either subpotent or superpotent for progesterone. The pH of most of the compounded suppository products was in the range of 4.22 to 7.68 with a median of 6.30 (normal vaginal pH is <5), whereas the gel product was 2.80. For compounded product from one of the pharmacies, microbial limits testing indicated CDC group IVC-2 and Comamonas acidovorans were detected. This data indicates that pharmacy compounded delivery systems for progesterone should be used with caution.

Temporal and spatial assessment of river surface water quality using multivariate statistical techniques: a study in Can Tho City, a Mekong Delta area, Vietnam.

PubMed

Phung, Dung; Huang, Cunrui; Rutherford, Shannon; Dwirahmadi, Febi; Chu, Cordia; Wang, Xiaoming; Nguyen, Minh; Nguyen, Nga Huy; Do, Cuong Manh; Nguyen, Trung Hieu; Dinh, Tuan Anh Diep

2015-05-01

The present study is an evaluation of temporal/spatial variations of surface water quality using multivariate statistical techniques, comprising cluster analysis (CA), principal component analysis (PCA), factor analysis (FA) and discriminant analysis (DA). Eleven water quality parameters were monitored at 38 different sites in Can Tho City, a Mekong Delta area of Vietnam from 2008 to 2012. Hierarchical cluster analysis grouped the 38 sampling sites into three clusters, representing mixed urban-rural areas, agricultural areas and industrial zone. FA/PCA resulted in three latent factors for the entire research location, three for cluster 1, four for cluster 2, and four for cluster 3 explaining 60, 60.2, 80.9, and 70% of the total variance in the respective water quality. The varifactors from FA indicated that the parameters responsible for water quality variations are related to erosion from disturbed land or inflow of effluent from sewage plants and industry, discharges from wastewater treatment plants and domestic wastewater, agricultural activities and industrial effluents, and contamination by sewage waste with faecal coliform bacteria through sewer and septic systems. Discriminant analysis (DA) revealed that nephelometric turbidity units (NTU), chemical oxygen demand (COD) and NH₃ are the discriminating parameters in space, affording 67% correct assignation in spatial analysis; pH and NO₂ are the discriminating parameters according to season, assigning approximately 60% of cases correctly. The findings suggest a possible revised sampling strategy that can reduce the number of sampling sites and the indicator parameters responsible for large variations in water quality. This study demonstrates the usefulness of multivariate statistical techniques for evaluation of temporal/spatial variations in water quality assessment and management.

[Effect of thermal treatments on the chemical characteristics of mora crab meat (Homalaspis plana)].

PubMed

Quitral Robles, Vilma; Abugoch, Lilian; Vinagre, Julia; Guarda, Abel; Larraín, M Angélica; Santana, Gabriela

2003-03-01

Marine species muscles present non-proteins nitrogenated compounds, used as quality index. They are total volatile basis (NBVT), trimethylamine oxide (TMAO) and trimethylamine (TMA). pH is considered too as a quality index. The aim of this work was to evaluate these parameters in a fresh and canned marine product from the V region, corresponding to mora crab (Homalaspis plana). Fresh pincer meat from mora crab was extracted and kept in ice until theits analysis and thermal process of the canned product. A 3(2) statistical design was applied, considering two variables with 3 levels: 15, 30 y 45 minutes time levels: 80 degrees, 100 degrees y 121 degrees C temperature levels. Nine conditions of time-temperature were obtained. The thermal treatment caused an increase in pH and BVT. The TMA was increased since reduction of TMAO.

A comparative study of kinetic and connectionist modeling for shelf-life prediction of Basundi mix.

PubMed

Ruhil, A P; Singh, R R B; Jain, D K; Patel, A A; Patil, G R

2011-04-01

A ready-to-reconstitute formulation of Basundi, a popular Indian dairy dessert was subjected to storage at various temperatures (10, 25 and 40 °C) and deteriorative changes in the Basundi mix were monitored using quality indices like pH, hydroxyl methyl furfural (HMF), bulk density (BD) and insolubility index (II). The multiple regression equations and the Arrhenius functions that describe the parameters' dependence on temperature for the four physico-chemical parameters were integrated to develop mathematical models for predicting sensory quality of Basundi mix. Connectionist model using multilayer feed forward neural network with back propagation algorithm was also developed for predicting the storage life of the product employing artificial neural network (ANN) tool box of MATLAB software. The quality indices served as the input parameters whereas the output parameters were the sensorily evaluated flavour and total sensory score. A total of 140 observations were used and the prediction performance was judged on the basis of per cent root mean square error. The results obtained from the two approaches were compared. Relatively lower magnitudes of percent root mean square error for both the sensory parameters indicated that the connectionist models were better fitted than kinetic models for predicting storage life.

Soil quality and carbon sequestration in a reclaimed coal mine spoil of Jharia coalfield, India

NASA Astrophysics Data System (ADS)

Mukhopadhyay, Sangeeta; Masto, Reginald; Ram, Lal

2016-04-01

Revegetation of coal mine spoil helps in carbon storage and the success of remediation depend on the selection of appropriate tree species. A study was conducted at the coalmine overburden dumps of Jharia Coalfield, Dhanbad, India to evaluate the impact of revegetation on the overall soil quality and carbon sequestration. Morphological parameters (tree height, diameter at breast height, tree biomass, wood specific gravity) of the dominant tree species (Acacia auriculiformis, Cassia siamea, Dalbergia sissoo and Leucaena leucocephala) growing on the mine spoil was recorded. Mine spoil samples were collected under the canopy cover of different tree species and analyzed for soil physical, chemical, and biological parameters. In general reclaimed sites had better soil quality than the reference site. For instance, D. sissoo and C. siamea improved soil pH (+28.5%, +27.9%), EC (+15.65%, +19%), cation exchange capacity (+58.7%, +52.3%), organic carbon (+67.5%, +79.5%), N (+97.2%, +75.7%), P (+98.2%, +76.9%), K (+31.8%, +37.4%), microbial biomass carbon (+143%, +164%) and dehydrogenase activity (+228%, +262%) as compared to the unreclaimed reference coal mine site. The concentration of polycyclic aromatic hydrocarbons (PAHs) decreased significantly in the reclaimed site than the reference spoil, C. siamea was found to be more promising for PAH degradation. The overall impact of tree species on the quality of reclaimed mine spoil cannot be assessed by individual soil parameters, as most of the parameters are interlinked and difficult to interpret. However, combination of soil properties into an integrated soil quality index provides a more meaningful assessment of reclamation potential of tree species. Principal component analysis (PCA) was used to identify key mine soil quality indicators to develop a soil quality index (SQI). Coarse fraction, pH, EC, soil organic carbon, P, Ca, S, and dehydrogenase activity were the most critical properties controlling growth of tree species. The indicator values were converted into a unitless score (0-1.00) and integrated into mine soil quality index (SQI). Higher SQI values were obtained for sites reclaimed with Dalbergia sissoo (0.585) and Cassia siamea (0.565) compared to the reference mine spoil (0.303). The calculated index was significantly correlated (r = 0.84) with plant growth parameters. The carbon dioxide sequestration potential of the reclaimed site was 133.3 t/ha, while the total tree carbon density was highest in D. sissoo (13.93 t/ha) and C. siamea (11.35 t/ha). Based on SQI and C sequestration potential, Dalbergia sissoo and Cassia siamea was found to be more suitable for reclamation of mine spoil.

Characterization of Argentine honeys on the basis of their mineral content and some typical quality parameters

PubMed Central

2014-01-01

Background The levels of 19 elements (As, Be, Ca, Cd, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, Se, Tl, U, V, Zn) from sixteen different Argentine production sites of unifloral [eucalyptus (Eucaliptus rostrata), chilca (Baccharis salicifolia), Algarrobo (Prosopis sp.), mistol (Ziziphus mistol) and citric] and multifloral honeys were measured with the aim to test the quality of the selected samples. Typical quality parameters of honeys were also determined (pH, sugar content, moisture). Mineral elements were determined by using inductively coupled plasma mass spectrometer (ICP-MS DRC). We also evaluated the suitability of honey as a possible biomonitor of environmental pollution. Thus, the sites were classified through cluster analysis (CA) and then pattern recognition methods such as Principal Component Analysis (PCA) and discriminant analysis (DA) were applied. Results Mean values for quality parameters were: pH, 4.12 and 3.81; sugar 82.1 and 82.0 °brix; moisture, 16.90 and 17.00% for unifloral and multifloral honeys respectively. The water content showed good maturity. Likewise, the other parameters confirmed the good quality of the honeys analysed. Potassium was quantitatively the most abundant metal, accounting for 92,5% of the total metal contents with an average concentration of 832.0 and 816.2 μg g-1 for unifloral and multifloral honeys respectively. Sodium was the second most abundant major metal in honeys with a mean value of 32.16 and 33.19 μg g-1 for unifloral and multifloral honeys respectively. Mg, Ca, Fe, Mn, Zn and Cu were present at low-intermediate concentrations. For the other 11 trace elements determined in this study (As, Be, Cd, Co, Cr, Ni, Pb, Se, Tl, U and V), the mean concentrations were very low or below of the LODs. The sites were classified through CA by using elements’ and physicochemical parameters data, then DA on the PCA factors was applied. Dendrograms identified three main groups. PCA explained 52.03% of the total variability with the first two factors. Conclusions In general, there are no evidences of pollution for the analysed honeys. The analytical results obtained for the Argentine honeys indicate the products’ high quality. In fact, most of the toxic elements were below LODs. The chemometric analysis combining CA, DA and PCA showed their aptness as useful tools for honey’s classification. Eventually, this study confirms that the use of honey as biomonitor of environmental contamination is not reliable for sites with low levels of contamination. PMID:25057287

Quality profile of litchi ( Litchi chinensis) cultivars from India and effect of radiation processing

NASA Astrophysics Data System (ADS)

Hajare, Sachin N.; Saxena, Sudhanshu; Kumar, Sanjeev; Wadhawan, Surbhi; More, Varsha; Mishra, B. B.; Narayan Parte, Madan; Gautam, Satyendra; Sharma, Arun

2010-09-01

Litchi ( Litchi chinensis) is a non-climacteric tropical fruit. The fruit has a short shelf-life making its marketing difficult. Physical, biochemical, microbiological, and organoleptic properties of two major commercially grown Indian cultivars of litchi, 'Shahi' and 'China' were studied. The effect of gamma radiation processing and low temperature storage on the above parameters was evaluated to standardize the optimal process parameters for shelf-life extension of litchi. Physical and biochemical parameters analyzed included weight, moisture, pH, titratable acidity, texture, color, total and reducing sugar, total soluble solids, vitamin C, and flavonoid content. Weight, moisture content, and pH in the fresh fruit ranged between 21-26 g, 74-77%, and 3.7-4.4, respectively, whereas, total and reducing sugar ranged 10-15, and 10-13 g%, respectively. In 'Shahi' vitamin C content was found to be around 17-19 mg%, whereas, in 'China' it was 22-28 mg%. Flavonoid content was in the range of 26-34 μg catechin equivalents/g of fresh fruit. Total surface and internal bacterial load was around 4 and 3 log cfu/g, respectively. Surface yeast-mold count (YMC) was ˜3 log cfu/g whereas internal YMC was ˜2 log cfu/g. Radiation treatment reduced microbial load in a dose dependent manner. Treatment at 0.5 kGy did not significantly affect the quality parameters of the fruit. Treated fruits retained the "good" organoleptic rating during storage. Thus, radiation treatment (0.5 kGy) in combination with low temperature (4 °C) storage achieved a shelf-life of 28 days for litchi fruit.

Guidelines and standard procedures for continuous water-quality monitors: Station operation, record computation, and data reporting

USGS Publications Warehouse

Wagner, Richard J.; Boulger, Robert W.; Oblinger, Carolyn J.; Smith, Brett A.

2006-01-01

The U.S. Geological Survey uses continuous water-quality monitors to assess the quality of the Nation's surface water. A common monitoring-system configuration for water-quality data collection is the four-parameter monitoring system, which collects temperature, specific conductance, dissolved oxygen, and pH data. Such systems also can be configured to measure other properties, such as turbidity or fluorescence. Data from sensors can be used in conjunction with chemical analyses of samples to estimate chemical loads. The sensors that are used to measure water-quality field parameters require careful field observation, cleaning, and calibration procedures, as well as thorough procedures for the computation and publication of final records. This report provides guidelines for site- and monitor-selection considerations; sensor inspection and calibration methods; field procedures; data evaluation, correction, and computation; and record-review and data-reporting processes, which supersede the guidelines presented previously in U.S. Geological Survey Water-Resources Investigations Report WRIR 00-4252. These procedures have evolved over the past three decades, and the process continues to evolve with newer technologies.

Modeling carbon dioxide, pH, and un-ionized ammonia relationships in serial reuse systems

USGS Publications Warehouse

Colt, J.; Watten, B.; Rust, M.

2009-01-01

In serial reuse systems, excretion of metabolic carbon dioxide has a significant impact on ambient pH, carbon dioxide, and un-ionized ammonia concentrations. This impact depends strongly on alkalinity, water flow rate, feeding rate, and loss of carbon dioxide to the atmosphere. A reduction in pH from metabolic carbon dioxide can significantly reduce the un-ionized ammonia concentration and increase the carbon dioxide concentrations compared to those parameters computed from influent pH. The ability to accurately predict pH in serial reuse systems is critical to their design and effective operation. A trial and error solution to the alkalinity-pH system was used to estimate important water quality parameters in serial reuse systems. Transfer of oxygen and carbon dioxide across the air-water interface, at overflow weirs, and impacts of substrate-attached algae and suspended bacteria were modeled. Gas transfer at the weirs was much greater than transfer across the air-water boundary. This simulation model can rapidly estimate influent and effluent concentrations of dissolved oxygen, carbon dioxide, and un-ionized ammonia as a function of water temperature, elevation, water flow, and weir type. The accuracy of the estimates strongly depends on assumed pollutional loading rates and gas transfer at the weirs. The current simulation model is based on mean daily loading rates; the impacts of daily variation loading rates are discussed. Copies of the source code and executable program are available free of charge.

Modeling Carbon Dioxide, pH and Un-Ionized Ammonia Relationships in Serial Reuse Systems

USGS Publications Warehouse

Watten, Barnaby J.; Rust, Michael; Colt, John

2009-01-01

In serial reuse systems, excretion of metabolic carbon dioxide has a significant impact on ambient pH, carbon dioxide, and un-ionized ammonia concentrations. This impact depends strongly on alkalinity, water flow rate, feeding rate, and loss of carbon dioxide to the atmosphere. A reduction in pH from metabolic carbon dioxide can significantly reduce the un-ionized ammonia concentration and increase the carbon dioxide concentrations compared to those parameters computed from influent pH. The ability to accurately predict pH in serial reuse systems is critical to their design and effective operation. A trial and error solution to the alkalinity–pH system was used to estimate important water quality parameters in serial reuse systems. Transfer of oxygen and carbon dioxide across the air–water interface, at overflow weirs, and impacts of substrate-attached algae and suspended bacteria were modeled. Gas transfer at the weirs was much greater than transfer across the air–water boundary. This simulation model can rapidly estimate influent and effluent concentrations of dissolved oxygen, carbon dioxide, and un-ionized ammonia as a function of water temperature, elevation, water flow, and weir type. The accuracy of the estimates strongly depends on assumed pollutional loading rates and gas transfer at the weirs. The current simulation model is based on mean daily loading rates; the impacts of daily variation loading rates are discussed. Copies of the source code and executable program are available free of charge.

Investigation of some disinfection chemicals and water quality parameters in swimming pools in the city center and districts of Canakkale, Turkey.

PubMed

Uysal, Tolga; Yilmaz, Selehattin; Turkoglu, Muhammet; Sadikoglu, Murat

2017-07-01

In this study, the variations in concentrations of some disinfection chemicals such as cyanuric acid (CyA), free chlorine (FC), and residual chlorine (RC), which affect human health, were investigated in the water of swimming pools. In addition, quality parameters such as temperature, pH, and total alkalinity (TA) in 44 swimming pools located in the city center and districts of Canakkale, Turkey, were examined in the summer period. While FC and RC amounts were analyzed using tablet tests with N-N-diethyl phenylenediamine (DPD 1) and potassium iodine (DPD 3) using the colorimetric method in the comparator, TA and CyA levels were measured with a photometric method. Temperature and pH were measured using YSI 556 MPS. Levels of CyA, FC, RC, pH, temperature, and TA varied between 0.00 and 725.0 mg L -1 (108.0 ± 111.4 mg L -1 ), 0.00 and 5.00 mg L -1 (1.60 ± 0.962 mg L -1 ), 0 and 0.55 mg L -1 (0.087 ± 0.059), 6.40 and 8.20 mg L -1 (7.30 ± 0.038 mg L -1 ), 22.0 and 32.0 °C (27.6 ± 1.45 °C), and 0.00 and 391.0 mg L -1 (129.3 ± 89.0), respectively. The findings were compared to standard limit values of the Ministry of Health of the Turkish Republic and other countries. Not only maximum concentrations of CyA but also the average concentrations exceeded the standard limit values of different countries in July and August with high tourism activity in Turkey. Although there is no problem in view of average values of other quality parameters, there are some problems in view of the maximum values in pool waters compared to standard limit values.

A quality by design (QbD) study on enoxaparin sodium loaded polymeric microspheres for colon-specific delivery.

PubMed

Hales, Dana; Vlase, Laurian; Porav, Sebastian Alin; Bodoki, Andreea; Barbu-Tudoran, Lucian; Achim, Marcela; Tomuță, Ioan

2017-03-30

The aim of this study was to apply quality by design (QbD) for pharmaceutical development of enoxaparin sodium microspheres for colon-specific delivery. The Process Parameters (CPPs) and Critical Quality Attributes (CQAs) were identified. A central composite experimental design was used in order to develop the design space of microspheres for colon-specific delivery that have the desired Quality Target Product Profile (QTPP). The CPPs studied were Eudragit® FS-30D/Eudragit® RS-PO ratio, poly(vinyl alcohol) (PVA) concentration and sodium chloride (NaCl) concentration. The encapsulation efficiency increased with NaCl concentration increase, the percentages of enoxaparin sodium reaching 94% for some formulations. Increasing the ratio Eudragit® FS-30D/Eudragit® RS-PO ensured a relatively complete release of enoxaparin sodium in the environment simulating the colonic pH. Based on these results, the optimum conditions were decided and the optimum formulation was prepared. The results obtained for the latter in terms of in vitro enoxaparin sodium release were good, the microparticles releasing only 9.42% enoxaparin sodium in acidic environment and 15.16% in the medium which simulated duodenal pH, but allowing the release of up to 89.24% in the medium which simulated colonic pH. The in vitro release profile of enoxaparin sodium was close to the ideal one, therefore the system was successfully designed using QbD approach. Copyright © 2017 Elsevier B.V. All rights reserved.

Dynamic Effects of Initial pH of Substrate on Biological Growth and Metamorphosis of Black Soldier Fly (Diptera: Stratiomyidae).

PubMed

Ma, Junhua; Lei, Yanyan; Rehman, Kashif Ur; Yu, Ziniu; Zhang, Jibin; Li, Wu; Li, Qing; Tomberlin, Jeffery K; Zheng, Longyu

2018-02-08

Edible insects have become a recognized alternative and sustainable source of high-quality proteins and fats for livestock or human consumption. In the production process of black soldier fly (BSF), (Hermetia illucens L. [Diptera: Stratiomyidae]), initial substrate pH is a critical parameter to ensure the best value of insect biomass, life history traits, and quality bio-fertilizer. This study examined the impact of initial pH values on BSF larvae production, development time, and adult longevity. The BSF were reared on artificial diet with initial pH of 2.0, 4.0, 6.0, 8.0, and 10.0; the control was set at 7.0. Final BSF larval weight was significantly greater in substrates having initial pH 6.0 (0.21 g), control 7.0 (0.20 g), and 10.0 (0.20 g) with no significant difference among them, whereas larval weight reared with initial pH 2.0 and 4.0 were lowest at 0.16 g (-23%). Prepupal weight was greatest when larvae were reared on substrates with initial pH 6.0 (0.18 g), control 7.0 (0.19 g), 8.0 (0.18 g), and 10.0 (0.18 g). In contrast, the prepupal weight of larvae reared on diets with initial pH 2.0 was lowest at 0.15 g (-22%). Larval development time was 21.19 d at pH 8.0, about 3 d (12.5%) shorter than that of those reared on diets with initial pH 6.0, 7.0 control, and 10.0. In all treatments, pH shifted to 5.7 after 3-4 d and 8.5 after 16-17 d except for two groups (2.0 and 4.0) where the pH remained slightly acidic 5.0 and 6.5, respectively. © The Author(s) 2018. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Prediction of Water Quality Parameters Using Statistical Methods: A Case Study in a Specially Protected Area, Ankara, Turkey

NASA Astrophysics Data System (ADS)

Alp, E.; Yücel, Ö.; Özcan, Z.

2014-12-01

Turkey has been making many legal arrangements for sustainable water management during the harmonization process with the European Union. In order to make cost effective and efficient decisions, monitoring network in Turkey has been expanding. However, due to time and budget constraints, desired number of monitoring campaigns can not be carried. Hence, in this study, independent parameters that can be measured easily and quickly are used to estimate water quality parameters in Lake Mogan and Eymir using linear regression. Nonpoint sources are one of the major pollutant components in Eymir and Mogan lakes. In this paper, a correlation between easily measurable parameters, DO, temperature, electrical conductivity, pH, precipitation and dependent variables, TN, TP, COD, Chl-a, TSS, Total Coliform is investigated. Simple regression analysis is performed for each season in Eymir and Mogan lakes by using SPSS Statistical program using the water quality data collected between 2006-2012. Regression analysis demonstrated significant linear relationship between measured and simulated concentrations for TN (R2=0.86), TP (R2=0.85), TSS (R2=0.91), Chl-a (R2=0.94), COD (R2=0.99), T. Coliform (R2=0.97) which are the best results in each season for Eymir and Mogan Lakes. The overall results of this study shows that by using easily measurable parameters even in ungauged situation the water quality of lakes can be predicted. Moreover, the outputs obtained from the regression equations can be used as an input for water quality models such as phosphorus budget model which is used to calculate the required reduction in the external phosphorus load to Lake Mogan to meet the water quality standards.

Influence of the halothane gene (HAL) on pork quality in two commercial crossbreeds.

PubMed

Silveira, A C P; Freitas, P F A; César, A S M; Cesar, A S M; Antunes, R C; Guimarães, E C; Batista, D F A; Torido, L C

2011-01-01

We evaluated the effect of the halothane (HAL) gene on the quality of pork in domestic pigs. Half-carcasses from two different commercial pig (Sus domestica) crossbreeds were analyzed, 46 of which were homozygous dominant (HAL(NN)) and 69 of which were heterozygous (HAL(Nn)) for the halothane gene. The measures included backfat thickness, lean meat percentage, carcass weight, pH 24 h after slaughtering, color, and drip loss; DNA was extracted from the haunch muscle. Swine with the HAL(Nn) genotype had less backfat thickness and higher lean meat percentages than swine with the HAL(NN) genotype. Yet, swine with the HAL(Nn) genotype had lower quality meat than those with the HAL(NN) swine. The pH at 24 h was lower in HAL(Nn) swine. The meat color was paler in HAL(Nn) animals, the drip loss was greater in those animals bearing the n allele, and the amount of intramuscular fat was not related to the halothane genotype. We conclude that bearers of the recessive allele of the halothane gene produce more meat, but with quality parameters that are inferior to those sought by consumers and industry.

Atomic Physics with the Goddard High Resolution Spectrograph on the Hubble Space Telescope. III; Oscillator Strengths for Neutral Carbon

NASA Technical Reports Server (NTRS)

Zsargo, J.; Federman, S. R.; Cardelli, Jason A.

1997-01-01

High quality spectra of interstellar absorption from C I toward beta(sup 1) S(sub co), rho O(sub ph) A, and chi O(sub ph) were obtained with the Goddard High Resolution Spectrograph on HST. Many weak lines were detected within the observed wavelength intervals: 1150-1200 A for beta(sup 1) S(sub co) and 1250-1290 A for rho O(sub ph) A and chi O(sub ph). Curve-of-growth analyses were performed in order to extract accurate column densities and Doppler parameters from lines with precise laboratory-based f-values. These column densities and b-values were used to obtain a self-consistent set of f-values for all the observed C I lines. A particularly important constraint was the need to reproduce data for more than one line of sight. For about 50% of the lines, the derived f-values differ appreciably from the values quoted by Morton.

Monitoring on The Quality and Quantity of DIY Rainwater Harvesting System

NASA Astrophysics Data System (ADS)

Kasmin, H.; Bakar, N. H.; Zubir, M. M.

2016-07-01

Rainwater harvesting is an alternative sources of water supply and can be used for potable and non-potable uses. It could helps to store treated rainwater for more beneficial use and also for flood mitigation. Sustainable approach for flooding problem reduction in urban areas is by slowing down the rate of surface runoff flows at source by providing more storage area/tank. In order to understand the performance of a rainwater harvesting system (RWH), a preliminary monitoring on a ‘do it yourself’ (DIY) RWH model with additional first -flush strategy for water quality treatment was done. The main concept behind first flush diversion is to prevent initial polluted rainwater from entering the storage tank. Based on seven rainfall events observed in Parit Raja, both quality and quantity of the rainfalls were analysed. For rainwater quality, the samples from first flush diverter and storage tank were taken to understand their performance based on pH, dissolved oxygen (DO), turbidity, total dissolved solid (TDS), total suspended solid (TSS), chemical oxygen demand (COD) and biochemical oxygen demand (BOD) parameters. While for rainwater quantity, hydrograph analysis were done based on the performance of total rainfall and runoff, peak flow of rainfall and runoff; and delayed time parameters. Based on Interim National Water Quality Standard (INWQS) and National Drinking Water Quality Standard (NDWQS), first flush diverter apparently helps on water quality improvement in storage tanks when pH, DO, TDS, TSS and turbidity were classified as Class I (INWQS) and is allowable for drinking; but BOD and COD parameters were classified as Class III (INWQS). Hence, it has potential to be used as potable usage but will need extensive treatment to reduce its poor microbial quality. Based on the maximum observed rainfall event which had total volume of 3195.5 liter, had peakflow reduction from 0.00071 m3/s to 0.00034 m3/s and delayed runoff between 5 and 10 minutes after rainfall started. It concludes that the performance of water retention could be due to total rainfall and the tank capacity. Therefore, RWH has a potential to be used as potable use and at the same time it also has a potential to reduce local urban flooding.

Explaining the variation in the shear force of lamb meat using sarcomere length, the rate of rigor onset and pH.

PubMed

Hopkins, D L; Toohey, E S; Lamb, T A; Kerr, M J; van de Ven, R; Refshauge, G

2011-08-01

The temperature when the pH=6.0 (temp@pH6) impacts on the tenderness and eating quality of sheep meat. Due to the expense, sarcomere length is not routinely measured as a variable to explain variation in shear force, but whether measures such as temp@pH6 are as useful a parameter needs to be established. Measures of rigor onset in 261 carcases, including the temp@pH6, were evaluated in this study for their ability to explain some of the variation in shear force. The results show that for 1 day aged product combinations of the temp@pH6, the pH at 18 °C and the pH at 24 h provided a larger reduction (almost double) in total shear force variation than sarcomere length alone, with pH at 24 h being the single best measure. For 5 day aged product, pH at 18 °C was the single best measure. Inclusion of sarcomere length did represent some improvement, but the marginal increase would not be cost effective. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

Quantitative structure-permeability relationships at various pH values for acidic and basic drugs and drug-like compounds.

PubMed

Oja, M; Maran, U

2015-01-01

Absorption in gastrointestinal tract compartments varies and is largely influenced by pH. Therefore, considering pH in studies and analyses of membrane permeability provides an opportunity to gain a better understanding of the behaviour of compounds and to obtain good permeability estimates for prediction purposes. This study concentrates on relationships between the chemical structure and membrane permeability of acidic and basic drugs and drug-like compounds. The membrane permeability of 36 acidic and 61 basic compounds was measured using the parallel artificial membrane permeability assay (PAMPA) at pH 3, 5, 7.4 and 9. Descriptive and/or predictive single-parameter quantitative structure-permeability relationships were derived for all pH values. For acidic compounds, membrane permeability is mainly influenced by hydrogen bond donor properties, as revealed by models with r(2) > 0.8 for pH 3 and pH 5. For basic compounds, the best (r(2) > 0.7) structure-permeability relationships are obtained with the octanol-water distribution coefficient for pH 7.4 and pH 9, indicating the importance of partition properties. In addition to the validation set, the prediction quality of the developed models was tested with folic acid and astemizole, showing good matches between experimental and calculated membrane permeabilities at key pHs. Selected QSAR models are available at the QsarDB repository ( http://dx.doi.org/10.15152/QDB.166 ).

Effects of toxic cyanobacteria and ammonia on flesh quality of blunt snout bream (Megalobrama amblycephala).

PubMed

Wang, Li; Chen, Chuanyue; Liu, Wanjing; Xia, Hu; Li, Jian; Zhang, Xuezhen

2017-03-01

Toxic cyanobacterial blooms result in the production of an organic biomass containing cyanotoxins (e.g. microcystins) and an elevated ammonia concentration in the water environment. The ingestion of toxic cyanobacteria and exposure to ammonia are grave hazards for fish. The present study assessed the effects of dietary toxic cyanobacteria and ammonia exposure on the flesh quality of blunt snout bream (Megalobrama amblycephala). Dietary toxic cyanobacteria and ammonia exposure had no impact on fish growth performance, fillet proximate composition and drip loss, whereas it significantly decreased fillet total amino acids, total essential amino acids, hardness and gumminess, and increased fillet ultimate pH as well as malondialdehyde content. However, there was no significant interaction between dietary toxic cyanobacteria and ammonia exposure on these parameters. Additionally, dietary toxic cyanobacteria significantly increased fillet initial pH, thaw loss and protein carbonyl content, whereas ammonia exposure did not. The results of the present study indicate that dietary toxic cyanobacteria and ammonia exposure reduced the quality of blunt snout bream fillet. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Effect of electrical stimulation and hot boning on the eating quality of Gannan yak longissimus lumborum.

PubMed

Lang, Yumiao; Sha, Kun; Zhang, Rui; Xie, Peng; Luo, Xin; Sun, Baozhong; Li, Haipeng; Zhang, Li; Zhang, Songshan; Liu, Xuan

2016-02-01

The objective of this study was to evaluate the effects of electrical stimulation (ES) versus non-electrical stimulation (NES) and type of boning (hot versus cold) on the eating quality of Gannan yak longissimus lumborum. Eighteen Gannan yak bulls were randomly divided into two groups: ES and NES. Hot boning (HB) and cold boning (CB) were applied to the left and right side of the carcasses, respectively. All of the four treatments missed the "ideal" pH/temperature window. HB reduced the rate of pH decline, decreased meat tenderness and water holding capacity. ES increased the rate of pH decline and improved yak meat tenderness (P<0.05); however, ES explained only 1% of the variation in WBSF. HB and ES had no significant effects on cooking loss, L* or b* values of yak meat. Postmortem aging increased yak meat tenderness and improved meat color parameters. HB had negative effects on yak meat quality, while ES could not reverse these deleterious effects. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparison of six crossbred lamb types: sensory, physical and nutritional meat quality characteristics.

PubMed

Hoffman, L C; Muller, M; Cloete, S W P; Schmidt, D

2003-12-01

The effect of crossbreeding on lamb meat quality was examined on the M. longissimus dorsi and M. semimembranosus of South African lamb breed combinations. The lambs were sired by Dormer (D) and Suffolk (S) rams and born to Merino (M), Dohne Merino (DM) and SA Mutton Merino (SAMM) ewes to give six breed combinations. Ratings of sensory attributes on the M. semimembranosus of the different lamb breed combinations were obtained from a trained descriptive panel. The moisture, total lipids, protein, ash, mineral content and fatty acid composition of the M. semimembranosus were also obtained. Physical parameters measured on the M. longissimus dorsi were: pH(48), drip loss, cooking loss and Warner-Bratzler shear force (WBS). Breed did not have a significant effect (P>0.05) on the sensory quality of lamb, except for D×SAMM lambs which only showed a significantly higher (P⩽0.05) initial juiciness compared to S×M. However, breed had a significant effect on pH(48), WBS, protein content and the fatty acid and mineral composition.

Water quality parameters response to temperature change in small shallow lakes

NASA Astrophysics Data System (ADS)

Xu, Lei; Li, Hua; Liang, Xinqiang; Yao, Yuxin; Zhou, Li; Cui, Xinyi

Effects of temperature (T) on water quality of three small shallow lakes in Taihu Lake region of China were investigated. The annual temperature was classified into three levels: low temperature (LT, 4 °C < T ⩽ 10 °C), middle temperature (MT, 10 °C < T ⩽ 20 °C), and high temperature (HT, 20 °C < T ⩽ 30 °C). Results showed that total nitrogen (TN) and total phosphorus (TP) concentrations might go to a fixed value (or range) in small shallow lakes receiving domestic sewage and farm drainage water. Nitrogen concentrations in the lakes were mainly in the form of nitrate (NO3-) at above concerned three temperature levels, and nitrogen concentrations in the forms of TN, TIN, and NO3- were increased with the increase of nutrient input. At the LT and MT levels, there was a series of good cubic curve relationships between temperatures and three N forms (TN, NO3- and NH4+). The temperatural inflexion change points in the curves were nearly at 7 °C and 14 °C, respectively. However, no significant relationship between temperature and any water quality parameter was observed at the HT level. The significant relationship of TIN to TN, NO3- to TN and NH4+ to dissolve oxygen (DO) was exist in three temperature portions, and TP to Chemical oxygen demand (COD, determined by potassium permanganate oxidation methods) in LT and MT, TP to pH or DO in HT also exist. COD were less than 6 mg L-1 at each temperature level, and pH values were the largest in HT than it in LT or MT. Thus, changes between temperature and water quality parameters (TN, NO3-, NH4+ and TP) obviously nearly in 7 °C or 14 °C in lakes show that water self-purification of natural small shallow lakes were obviously with temperature changed.

Effects of Pre and Post-Rigor Marinade Injection on Some Quality Parameters of Longissimus Dorsi Muscles

PubMed Central

Fadıloğlu, Eylem Ezgi; Serdaroğlu, Meltem

2018-01-01

Abstract This study was conducted to evaluate the effects of pre and post-rigor marinade injections on some quality parameters of Longissimus dorsi (LD) muscles. Three marinade formulations were prepared with 2% NaCl, 2% NaCl+0.5 M lactic acid and 2% NaCl+0.5 M sodium lactate. In this study marinade uptake, pH, free water, cooking loss, drip loss and color properties were analyzed. Injection time had significant effect on marinade uptake levels of samples. Regardless of marinate formulation, marinade uptake of pre-rigor samples injected with marinade solutions were higher than post rigor samples. Injection of sodium lactate increased pH values of samples whereas lactic acid injection decreased pH. Marinade treatment and storage period had significant effect on cooking loss. At each evaluation period interaction between marinade treatment and injection time showed different effect on free water content. Storage period and marinade application had significant effect on drip loss values. Drip loss in all samples increased during the storage. During all storage days, lowest CIE L* value was found in pre-rigor samples injected with sodium lactate. Lactic acid injection caused color fade in pre-rigor and post-rigor samples. Interaction between marinade treatment and storage period was found statistically significant (p<0.05). At day 0 and 3, the lowest CIE b* values obtained pre-rigor samples injected with sodium lactate and there were no differences were found in other samples. At day 6, no significant differences were found in CIE b* values of all samples. PMID:29805282

Effects of Pre and Post-Rigor Marinade Injection on Some Quality Parameters of Longissimus Dorsi Muscles.

PubMed

Fadıloğlu, Eylem Ezgi; Serdaroğlu, Meltem

2018-04-01

This study was conducted to evaluate the effects of pre and post-rigor marinade injections on some quality parameters of Longissimus dorsi (LD) muscles. Three marinade formulations were prepared with 2% NaCl, 2% NaCl+0.5 M lactic acid and 2% NaCl+0.5 M sodium lactate. In this study marinade uptake, pH, free water, cooking loss, drip loss and color properties were analyzed. Injection time had significant effect on marinade uptake levels of samples. Regardless of marinate formulation, marinade uptake of pre-rigor samples injected with marinade solutions were higher than post rigor samples. Injection of sodium lactate increased pH values of samples whereas lactic acid injection decreased pH. Marinade treatment and storage period had significant effect on cooking loss. At each evaluation period interaction between marinade treatment and injection time showed different effect on free water content. Storage period and marinade application had significant effect on drip loss values. Drip loss in all samples increased during the storage. During all storage days, lowest CIE L* value was found in pre-rigor samples injected with sodium lactate. Lactic acid injection caused color fade in pre-rigor and post-rigor samples. Interaction between marinade treatment and storage period was found statistically significant ( p <0.05). At day 0 and 3, the lowest CIE b* values obtained pre-rigor samples injected with sodium lactate and there were no differences were found in other samples. At day 6, no significant differences were found in CIE b* values of all samples.

The effects of electrical stunning voltage on meat quality, plasma parameters, and protein solubility of broiler breast meat.

PubMed

Huang, J C; Yang, J; Huang, M; Chen, K J; Xu, X L; Zhou, G H

2017-03-01

This study was designed to compare the effects of different stunning voltages of pulsed direct current on meat quality of broilers. For this purpose, plasma parameters, blood loss, carcass damage, and meat water holding capacity, color, shear force, pH, and protein solubility were analyzed. A total of 400 broilers were divided into 5 treatment groups and stunned with 5, 15, 25, 35, and 45 V at 750 Hz and 10 s, respectively. Blood samples were collected immediately after cutting the neck. Pectoralis major muscles were removed from the carcass after chilling and placed on ice. Breast muscle pH and meat color were determined at both 2 and 24 h postmortem. Dripping loss, cooking loss, pressing loss, and cooked breast meat shear values were determined after 24 h postmortem. The 5 V treatment significantly increased (P < 0.05) blood plasma corticosterone and lactate concentration compared with the other groups. The carcass damage of wings, Pectoralis major, and Pectoralis minor was significant in the 5, 35, and 45 V groups. The pH of 2 h postmortem in the 5 and 45 V groups was significantly lower (P < 0.05) than in the 15 and 25 V groups. In the 5 and 45 V groups, the protein solubility and shear force value were significantly lower (P < 0.05) and dripping loss was significantly higher (P < 0.05) than the other groups. © 2016 Poultry Science Association Inc.

Noninvasive pH monitoring of platelet concentrates: a large field test.

PubMed

Gkoumassi, Effimia; Klein-Bosgoed, Christa; Dijkstra-Tiekstra, Margriet J; de Korte, Dirk; de Wildt-Eggen, Janny

2013-10-01

Developing new quality control methods for platelet concentrates (PCs) can contribute to increasing transfusion safety and efficiency. The aim of this study was to investigate in a large field test the quality of expired PCs and whether 100% noninvasive pH monitoring can be used to predict PC quality. The pH of 13,693 PCs produced for transfusion was monitored daily using Blood Storage, Inc.'s pH sterile, automated fluoroscopic evaluation technology. Upon indication of compromised quality or expiration, PCs were returned and in vitro tests were performed. A total of 998 PCs were returned, of which 962 outdated, 26 had a positive BacT/ALERT reaction, seven had aggregates, one was without swirl, one had low pH, and one had high pH. BacT/ALERT was faster in identifying bacterial contamination than pH measurements. The pH at the end of the storage period was significantly lower than at the beginning. In vitro tests indicated that while the PC quality was acceptable upon expiration, it rapidly declined after expiration. In this setting where the vast majority of PCs were of good quality and within acceptable pH limits, daily, noninvasive routine pH measurement has limited added value in identifying quality-compromised PCs. © 2013 Sanquin Research. Transfusion © 2013 American Association of Blood Banks.

Hydrogeochemical quality and suitability studies of groundwater in northern Bangladesh.

PubMed

Islam, M J; Hakim, M A; Hanafi, M M; Juraimi, Abdul Shukor; Aktar, Sharmin; Siddiqa, Aysha; Rahman, A K M Shajedur; Islam, M Atikul; Halim, M A

2014-07-01

Agriculture, rapid urbanization and geochemical processes have direct or indirect effects on the chemical composition of groundwater and aquifer geochemistry. Hydro-chemical investigations, which are significant for assessment of water quality, were carried out to study the sources of dissolved ions in groundwater of Dinajpur district, northern Bangladesh. The groundwater samplish were analyzed for physico-chemical properties like pH, electrical conductance, hardness, alkalinity, total dissolved solids and Ca2+, Mg2+, Na+, K+, CO3(2-), HCO3(-), SO4(2-) and Cl- ions, respectively. Based on the analyses, certain parameters like sodium adsorption ratio, soluble sodium percentage, potential salinity, residual sodium carbonate, Kelly's ratio, permeability index and Gibbs ratio were also calculated. The results showed that the groundwater of study area was fresh, slightly acidic (pH 5.3-6.4) and low in TDS (35-275 mg I(-1)). Ground water of the study area was found suitable for irrigation, drinking and domestic purposes, since most of the parameters analyzed were within the WHO recommended values for drinking water. High concentration of NO3- and Cl- was reported in areas with extensive agriculture and rapid urbanization. Ion-exchange, weathering, oxidation and dissolution of minerals were major geochemical processes governing the groundwater evolution in study area. Gibb's diagram showed that all the samples fell in the rock dominance field. Based on evaluation, it is clear that groundwater quality of the study area was suitable for both domestic and irrigation purposes.

Limnology of Jagatpur wetland, Bhagalpur (Bihar), India.

PubMed

Kumar, Brajnandan

2011-10-01

The water quality in Jagatpur wetland was assessed in terms of physico - chemical characteristics for two years, between August 2003-July 2005. The variations in different physico-chemical parameters have been discussed in this paper in relation to fluctuating climatic condition. The wetland is experiencing racing eutrophication as evidenced by pH was acidic to alkaline, total hardness was considerably high, bicarbonate was in moderate amount, phosphate-phosphorus content was in a range of medium to high and higher values of COD. The present status of the quality of water of Jagatpur wetland is delineated in this paper.

Water-quality data for the ground-water network in eastern Broward County, Florida, 1983-84

USGS Publications Warehouse

Waller, B.G.; Cannon, F.L.

1986-01-01

During 1983-84, groundwater from 63 wells located at 31 sites throughout eastern Broward County, Florida, was sampled and analyzed to determine baseline water quality conditions. The physical and chemical parameters analyzed included field measurements (pH and temperature), physical characteristics (color, turbidity, and specific conductance), major inorganic ions, nutrients, (nitrogen, phosphorus and carbon), selected metals, and total phenolic compounds. Groundwater samples were collected at the end of the dry season (April) and during the wet season (July and September). These data are tabulated, by well, in this report. (USGS)

Geographical Information System based assessment of spatiotemporal characteristics of groundwater quality of upland sub-watersheds of Meenachil River, parts of Western Ghats, Kottayam District, Kerala, India

NASA Astrophysics Data System (ADS)

Vijith, H.; Satheesh, R.

2007-09-01

Hydrogeochemistry of groundwater in upland sub-watersheds of Meenachil river, parts of Western Ghats, Kottayam, Kerala, India was used to assess the quality of groundwater for determining its suitability for drinking and agricultural purposes. The study area is dominated by rocks of Archaean age, and Charnonckite is dominated over other rocks. Rubber plantation dominated over other types of the vegetation in the area. Though the study area receives heavy rainfall, it frequently faces water scarcity as well as water quality problems. Hence, a Geographical Information System (GIS) based assessment of spatiotemporal behaviour of groundwater quality has been carried out in the region. Twenty-eight water samples were collected from different wells and analysed for major chemical constituents both in monsoon and post-monsoon seasons to determine the quality variation. Physical and chemical parameters of groundwater such as pH, dissolved oxygen (DO), total hardness (TH), chloride (Cl), nitrate (NO3) and phosphate (PO4) were determined. A surface map was prepared in the ArcGIS 8.3 (spatial analyst module) to assess the quality in terms of spatial variation, and it showed that the high and low regions of water quality varied spatially during the study period. The influence of lithology over the quality of groundwater is negligible in this region because majority of the area comes under single lithology, i.e. charnockite, and it was found that the extensive use of fertilizers and pesticides in the rubber, tea and other agricultural practices influenced the groundwater quality of the region. According to the overall assessment of the basin, all the parameters analysed are below the desirable limits of WHO and Indian standards for drinking water. Hence, considering the pH, the groundwater in the study area is not suitable for drinking but can be used for irrigation, industrial and domestic purposes. The spatial analysis of groundwater quality patterns of the study area shows seasonal fluctuations and these spatial patterns of physical and chemical constituents are useful in deciding water use strategies for various purposes.

Relationship between water quality parameters and the survival of indicator microorganisms - Escherichia coli - in a stormwater wetland.

PubMed

Cheng, Jing; Niu, Siping; Kim, Youngchul

2013-01-01

Indicator microorganisms - Escherichia coli - in a stormwater wetland controlling non-point source pollution in the Keum River basin was studied and the relationship between water quality parameters and the survival of E. coli was investigated by Pearson correlation analysis based on 16 sets of data collected on dry days. A significant seasonal variation of the density of E. coli was observed in the influent and effluent. A dominant decay of E. coli was found in almost all the wetland components. In the settling pond, the density was observed to vary negatively with pH and the removal of total suspended solids, and the decay was promoted by solar radiation. In the aeration pond, the survival of E. coli was encouraged negatively by the dilution effect, unfavorable increase of dissolved oxygen (DO) and sedimentation with coarse particles. In the marsh wetland, the reduction of E. coli was positively influenced by UV radiation, obvious increase of pH, DO and sedimentation with algae and particles. In the polishing pond, the introduction of E. coli with avian feces and growth of the bacteria were more prevalent than decay. Although this introduction or growth was almost negligible, further study will be conducted in the future.

Characterization of Surface Water and Groundwater Quality in the Lower Tano River Basin Using Statistical and Isotopic Approach.

NASA Astrophysics Data System (ADS)

Edjah, Adwoba; Stenni, Barbara; Cozzi, Giulio; Turetta, Clara; Dreossi, Giuliano; Tetteh Akiti, Thomas; Yidana, Sandow

2017-04-01

Adwoba Kua- Manza Edjaha, Barbara Stennib,c,Giuliano Dreossib, Giulio Cozzic, Clara Turetta c,T.T Akitid ,Sandow Yidanae a,eDepartment of Earth Science, University of Ghana Legon, Ghana West Africa bDepartment of Enviromental Sciences, Informatics and Statistics, Ca Foscari University of Venice, Italy cInstitute for the Dynamics of Environmental Processes, CNR, Venice, Italy dDepartment of Nuclear Application and Techniques, Graduate School of Nuclear and Allied Sciences University of Ghana Legon This research is part of a PhD research work "Hydrogeological Assessment of the Lower Tano river basin for sustainable economic usage, Ghana, West - Africa". In this study, the researcher investigated surface water and groundwater quality in the Lower Tano river basin. This assessment was based on some selected sampling sites associated with mining activities, and the development of oil and gas. Statistical approach was applied to characterize the quality of surface water and groundwater. Also, water stable isotopes, which is a natural tracer of the hydrological cycle was used to investigate the origin of groundwater recharge in the basin. The study revealed that Pb and Ni values of the surface water and groundwater samples exceeded the WHO standards for drinking water. In addition, water quality index (WQI), based on physicochemical parameters(EC, TDS, pH) and major ions(Ca2+, Na+, Mg2+, HCO3-,NO3-, CL-, SO42-, K+) exhibited good quality water for 60% of the sampled surface water and groundwater. Other statistical techniques, such as Heavy metal pollution index (HPI), degree of contamination (Cd), and heavy metal evaluation index (HEI), based on trace element parameters in the water samples, reveal that 90% of the surface water and groundwater samples belong to high level of pollution. Principal component analysis (PCA) also suggests that the water quality in the basin is likely affected by rock - water interaction and anthropogenic activities (sea water intrusion). This was confirm by further statistical analysis (cluster analysis and correlation matrix) of the water quality parameters. Spatial distribution of water quality parameters, trace elements and the results obtained from the statistical analysis was determined by geographical information system (GIS). In addition, the isotopic analysis of the sampled surface water and groundwater revealed that most of the surface water and groundwater were of meteoric origin with little or no isotopic variations. It is expected that outcomes of this research will form a baseline for making appropriate decision on water quality management by decision makers in the Lower Tano river Basin. Keywords: Water stable isotopes, Trace elements, Multivariate statistics, Evaluation indices, Lower Tano river basin.

Assessing the Quality of PhD Dissertations. A Survey of External Committee Members

ERIC Educational Resources Information Center

Kyvik, Svein; Thune, Taran

2015-01-01

This article reports on a study of the quality assessment of doctoral dissertations, and asks whether examiner characteristics influence assessment of research quality in PhD dissertations. Utilising a multi-dimensional concept of quality of PhD dissertations, we look at differences in assessment of research quality, and particularly test whether…

Spatio-temporal variability of hydro-chemical characteristics of coastal waters of Gulf of Mannar Marine Biosphere Reserve (GoMMBR), South India

NASA Astrophysics Data System (ADS)

Kathiravan, K.; Natesan, Usha; Vishnunath, R.

2017-03-01

The intention of this study was to appraise the spatial and temporal variations in the physico-chemical parameters of coastal waters of Rameswaram Island, Gulf of Mannar Marine Biosphere Reserve, south India, using multivariate statistical techniques, such as cluster analysis, factor analysis and principal component analysis. Spatio-temporal variations among the physico-chemical parameters are observed in the coastal waters of Gulf of Mannar, especially during northeast and post monsoon seasons. It is inferred that the high loadings of pH, temperature, suspended particulate matter, salinity, dissolved oxygen, biochemical oxygen demand, chlorophyll a, nutrient species of nitrogen and phosphorus strongly determine the discrimination of coastal water quality. Results highlight the important role of monsoonal variations to determine the coastal water quality around Rameswaram Island.

Impact of Cultivation Conditions, Ethylene Treatment, and Postharvest Storage on Selected Quality and Bioactivity Parameters of Kiwifruit "Hayward" Evaluated by Analytical and Chemometric Methods.

PubMed

Park, Yong Seo; Polovka, Martin; Ham, Kyung-Sik Ham; Park, Yang-Kyun; Vearasilp, Suchada; Namieśnik, Jacek; Toledo, Fernando; Arancibia-Avila, Patricia; Gorinstein, Shela

2016-09-01

Organic, semiorganic, and conventional "Hayward" kiwifruits, treated with ethylene for 24 h and stored during 10 days, were assessed by UV spectrometry, fluorometry, and chemometrical analysis for changes in selected characteristics of quality (firmness, dry matter and soluble solid contents, pH, and acidity) and bioactivity (concentration of polyphenols via Folin-Ciocalteu and p-hydroxybenzoic acid assays). All of the monitored qualitative parameters and characteristics related to bioactivity were affected either by cultivation practices or by ethylene treatment and storage. Results obtained, supported by statistical evaluation (Friedman two-way ANOVA) and chemometric analysis, clearly proved that the most significant impact on the majority of the evaluated parameters of quality and bioactivity of "Hayward" kiwifruit had the ethylene treatment followed by the cultivation practices and the postharvest storage. Total concentration of polyphenols expressed via p-hydroxybenzoic acid assay exhibited the most significant sensitivity to all three evaluated parameters, reaching a 16.5% increase for fresh organic compared to a conventional control sample. As a result of postharvest storage coupled with ethylene treatment, the difference increased to 26.3%. Three-dimensional fluorescence showed differences in the position of the main peaks and their fluorescence intensity for conventional, semiorganic, and organic kiwifruits in comparison with ethylene nontreated samples.

Variability of Remote Sensing Spectral Indices in Boreal Lake Basins

NASA Astrophysics Data System (ADS)

Hakala, T.; Pölönen, I.; Honkavaara, E.; Näsi, R.; Hakala, T.; Lindfors, A.

2018-05-01

Remotely sensed hyperspectral data has widely been used to determine water quality parameters in oceanic waters. However in freshwater basins the dependence between the hyperspectral data and the parameters is more complicated. In this work some ideas are presented concerning the study of this dependence. The data used in this study were collected from the lake Hiidenvesi in southern Finland. The hyperspectral data consists of reflectances in 36 bands in the wavelength area 508…878 nm and the separately measured water quality parameters are turbidity, blue-green algae, chlorophyll, pH and dissolved oxygen. Hyperspectral data was used as bare band reflectances, but also in the form of two simple spectral indices: ratio A / B and difference A - B, where A and B go through all the bands. The correlations of the indices with the parameters were presented visually as 1- or 2-dimensional arrays. To examine the significance on the results of different variables, the data was classified in two different ways: the natural basins and the values of the water quality parameters. It was noticed that the variability of the correlation arrays was particularly strong among different basins in both the magnitude of correlation and the best performing indices. Further studies are needed to clarify which features of the basins are of most importance in predicting the shapes of the correlation arrays.

Response of aquatic macro-invertebrate diversity to environmental factors along the Lower Komati River in Swaziland

NASA Astrophysics Data System (ADS)

Dlamini, Vuyisile; Hoko, Zvikomborero; Murwira, Amon; Magagula, Cebisile

This paper assessed macro-invertebrates diversity as an indicator of aquatic ecosystem health in the Lower Komati River. It also investigated whether this diversity is a function of physico-chemical water quality parameters along an area with major agricultural activities. Bio-assessment of aquatic macro-invertebrates present in the Lower Komati River was carried out at seven sites on the river over 3 months. Water samples were also collected at these sites and analysed for pH, dissolved oxygen, electrical conductivity, turbidity, nitrates, ammonia and ortho-phosphates according to standard methods. It was found out that species diversity along agricultural fields was not significantly different ( p > 0.05) between successive sites. However, nitrate and turbidity among the physico-chemical parameters indicated a significant variation of mean values ( p < 0.05) between sites. With the exception of turbidity, no significant relationship ( p > 0.05) was found between diversity and water quality parameters. Principal Component Analysis also demonstrated the influence of turbidity in the sub-catchments as it was the only parameter that showed a significant loading in all Principal Components. Turbidity seems to be the main parameter influencing aquatic macro-invertebrate diversity in the Lower Komati River at the time of study. The study recommends further studies to determine the seasonal variation of the impact of water quality on macro-invertebrates diversity.

River water pollution condition in upper part of Brantas River and Bengawan Solo River

NASA Astrophysics Data System (ADS)

Roosmini, D.; Septiono, M. A.; Putri, N. E.; Shabrina, H. M.; Salami, I. R. S.; Ariesyady, H. D.

2018-01-01

Wastewater and solid waste from both domestic and industry have been known to give burden on river water quality. Most of river water quality problem in Indonesia has start in the upper part of river due to anthropogenic activities, due to inappropriate land use management including the poor wastewater infrastructure. Base on Upper Citarum River Water pollution problem, it is interesting to study the other main river in Java Island. Bengawan Solo River and Brantas River were chosen as the sample in this study. Parameters assessed in this study are as follows: TSS, TDS, pH, DO, and hexavalent chromium. The status of river water quality are assess using STORET method. Based on (five) parameters, STORET value showed that in Brantas River, Pagerluyung monitoring point had the worst quality relatively compared to other monitoring point in Brantas River with exceeding copper, lead and tin compared to the stream standard in East Java Provincial Regulation No. 2 in 2008. Brantas River was categorized as lightly polluted river based on monitoring period 2011-2015 in 5 monitoring points, namely Pendem, Sengguruh, Kademangan, Meritjan and Kertosono.

A GIS-based Model for Urban Change and Implications for Water Quality in the Pontchartrain Basin

NASA Astrophysics Data System (ADS)

Carstens, D.; Amer, R. M.

2017-12-01

The combination of remote sensing techniques and Geographic Information Systems (GIS) to measure water quality allows researchers to monitor changes in various water quality parameters over temporal and spatial scales that are not always readily apparent from in situ measurements. Water has a distinct spectral behavior in comparison to soil, vegetation and urban, and therefore can be distinguished from surrounding environments. This study involves using remote sensing and GIS methods to map urban sprawl and its resulting influences on water quality in the Pontchartrain Basin over the last three decades. Two images of Landsat Thematic Mapper (TM) were taken in October 1985 and two images of Landsat Operational Land Imager (OLI) were taken in 2015 were atmospherically corrected and processed to map urban sprawl and influences on water quality of Pontchartrain Basin in the last three decades. To accomplish this, a normalized difference building index (NDBI) was developed for Landsat images. The NDBI was calculated from (NIR - SWIR) / (NIR + SWIR), where SWIR is the longest wavelength. The normalized difference vegetation index (NDVI), the normalized difference soil index (NDSI), and the normalized difference water index (NDWI) were also calculated for Landsat images. A GIS model was developed by integrating the NDBI, NDVI, NDSI, and NDWI, and yielded urban/non-urban/water boundary maps with 30-m resolution. Results indicate that urban areas have increased approximately from 25,643 km2 to 26,677 km2, which represents about 4.0% change from non-urban to urban in the last 3 decades. The results are in a good agreement with the U.S. Census data, which indicated that there is a 12.25% increase in population over the last 25 years in the 16 parishes of the Pontchartrain Basin. Urban changes were compared with changes of water quality parameters in PONTCHARTRAIN BASIN, which include pH, specific conductance, nitrogen, phosphorous, and dissolved oxygen. The results show that decrease in dissolved oxygen and phosphorus, and the increase in specific conductance, nitrogen and pH from 1985 to 2015 are consistent with the rate of urban sprawl that occurred during this time period. Future work will include analysis of changes in agricultural and industrial activities and correlation with changes of water quality parameters.

Kombucha fermentation test used for various types of herbal teas

NASA Astrophysics Data System (ADS)

Novi Primiani, C.; Pujiati; Mumtahanah, Mahda; Ardhi, Waskitho

2018-05-01

Tea is a common drink in the community, the benefits of tea can be improved by processing fermented tea called kombucha. Kombucha is a refreshing drink made from tea water plus sugar, obtained through the fermentation process by acetic acid bacteria and fungi, is consumed for its health benefits. The common Kombucha starter is called SCOOBY (Simbyotic of Bacteri and Yeast). Kombucha research using herbal tea is very rarely done, it is necessary kombucha research using a variety of herbal teas to determine the quality of its inhibitory power against bacteria and its quality compared with kombucha berkomposisi tea Camelia sinensis in general. The purpose of this research was to know kombucha quality with ph parameter, thickness of nata, total acid and its inhibitory power to Escherchia coli and Staphylococcus aureus bacteria. This research used Randomized Block Design (RAK) method using 1 tea type treatment, with 3 replications. The first type of green tea (P1), roselle tea (P2), mangosteen peel tea (P3), soursop leaf tea (P4), moringa leaf tea (P5) and yellow leaf tea (P6), so there are 18 treatment combinations. Based on statistical analysis, there was influence of tea type to kombucha quality. Treatments of P1 and P2 were found to have an optimum and significant effect for kombucha. the results in level of acidity [pH] on green tea (P1) was 3.05, nata thickness of 4.63 and total acid of 0.69. Acidity in roselle tea (P2) was 2.86, nata thickness of 3.83, and total acid of 0.71. While the lowest quality was found in the treatment of mangosteen peel (P3) tea with pH 2.57, nata thickness of 0.35, and total acid of 0.79.

Interrelationships between fish tissue mercury concentrations and water quality for South Dakota natural lakes and impoundments

USGS Publications Warehouse

Chipps, Steven R.; Stetler, Larry; Stone, James J.; McCutcheon, Cindy M.

2011-01-01

The purpose of this study was to determine whether water quality parameters commonly associated with primary productivity may be used to predict the susceptibility of a specific water body to exceed proposed fish consumption advisory limitation of 0.3 mg kg−1. South Dakota currently has nine lakes and impoundments that exceed fish tissue mercury advisory limits of 1.0 mg kg−1 total mercury, far exceeding US Environmental Protection Agency and Food and Drug Administration 0.3 mg kg−1 consumption criteria. Previous studies suggest that increased aquatic productivity may mitigate the effects of biological production and subsequent uptake of methyl mercury through bio-dilution; however, it is uncertain whether these trends may exist within highly alkaline and highly productive aquatic conditions common to South Dakota lakes and impoundments. Water quality parameters and fish tissue mercury data for northern pike and walleye were collected and assessed using existing South Dakota Department of Environment and Natural Resources and Game Fish and Parks data. The data was initially screened using both parametric linear regression and non-parametric Mann–Whitney rank sum comparisons and further assessed using binary logistic regression and stepwise logistic regression methodology. Three separate phosphorus measurements (total, total dissolved, and Trophic State Index) and pH were determined to significantly correlate with increased mercury concentrations for the northern pike-in-impoundments model. However, phosphorus surprisingly was not a strong predictor for the remaining scenarios modeled. For the northern pike-in-natural lakes models, alkalinity was the most significant water quality parameter predicting increased mercury concentrations. Mercury concentrations for the walleye-in-natural lakes models were further influenced by pH and alkalinity. The water quality and fish tissue mercury interrelationships determined within this study suggest aquatic productivity, and consequential eutrophication processes appear to be reasonable indicators of fish tissue mercury susceptibility for aquatic conditions common to South Dakota and highlight the continuing need to minimize eutrophication through effective watershed management strategies.

Botanical discrimination of Greek unifloral honeys with physico-chemical and chemometric analyses.

PubMed

Karabagias, Ioannis K; Badeka, Anastasia V; Kontakos, Stavros; Karabournioti, Sofia; Kontominas, Michael G

2014-12-15

The aim of the present study was to investigate the possibility of characterisation and classification of Greek unifloral honeys (pine, thyme, fir and orange blossom) according to botanical origin using volatile compounds, conventional physico-chemical parameters and chemometric analyses (MANOVA and Linear Discriminant Analysis). For this purpose, 119 honey samples were collected during the harvesting period 2011 from 14 different regions in Greece known to produce unifloral honey of good quality. Physico-chemical analysis included the identification and semi quantification of fifty five volatile compounds performed by Headspace Solid Phase Microextraction coupled to gas chromatography/mass spectroscopy and the determination of conventional quality parameters such as pH, free, lactonic, total acidity, electrical conductivity, moisture, ash, lactonic/free acidity ratio and colour parameters L, a, b. Results showed that using 40 diverse variables (30 volatile compounds of different classes and 10 physico-chemical parameters) the honey samples were satisfactorily classified according to botanical origin using volatile compounds (84.0% correct prediction), physicochemical parameters (97.5% correct prediction), and the combination of both (95.8% correct prediction) indicating that multi element analysis comprises a powerful tool for honey discrimination purposes. Copyright © 2014 Elsevier Ltd. All rights reserved.

Improvement of chemical monitoring of water-chemistry conditions at thermal power stations based on electric conductivity and pH measurements

NASA Astrophysics Data System (ADS)

Larin, A. B.; Larin, B. M.

2016-05-01

The increased requirements to the quality of the water heat conductor for working superhigh (SHP) and supercritical (SCP) pressure power plants and promising units, including combined-cycle gas turbine (CCGT) units and power plants with ultrasupercritical parameters (USCPs), can largely be satisfied through specific electric conductivity and pH measurements for cooled heat conductor samples combined with calculations of ionic equilibria and indirect measurements of several specified and diagnostic parameters. The possibility of calculating the ammonia and chloride concentrations and the total concentration of hardness and sodium cations in the feed water of drum-type boilers and the phosphate and salt contents in boiler water was demonstrated. An equation for evaluating the content of potentially acid substances in the feed water of monotube boilers was suggested. The potential of the developed procedure for evaluating the state of waterchemistry conditions (WCCs) in power plants with CCGT units was shown.

Effect of electrical stunning frequency on meat quality, plasma parameters, and protein solubility of broilers.

PubMed

Huang, J C; Yang, J; Zhang, B H; Huang, M; Chen, K J; Xu, X L; Zhou, G H

2017-08-01

This study was designed to compare the effects of different stunning frequencies of pulsed direct current on meat quality of broilers. This was achieved by investigating plasma parameters, blood loss, carcass damage, meat water-holding capacity, meat color, meat shear value, muscle pH, and protein solubility. A total of 400 broilers was divided into 5 treatment groups and stunned with 500, 600, 700, 800, and 900 Hz at 15 V for 10 seconds. Blood samples were collected immediately after cutting the neck. Pectoralis major muscles were removed from the carcass after chilling and placed in ice. Breast muscle pH and meat color were determined at both 2 and 24 h postmortem. Drip loss, cooking loss, pressing loss, and cooked breast meat-shear values were determined at 24 h postmortem. Treatment at 500 and 900 Hz significantly increased (P < 0.05) blood plasma corticosterone and lactate concentrations compared with the 700 Hz group. The wing damage of carcasses was significantly serious in the 500, 800, and 900 Hz groups. The Pectoralis minor damage of carcesses in the 700 Hz group was significantly lower (P < 0.05) compared to the other stunning groups. The pH at 2 h postmortem in the 500 and 900 Hz groups was significantly lower (P < 0.05) than in other groups. However, the final pH and meat color were not affected by stunning frequency. In the 500 and 900 Hz groups, the protein solubility and shear force values were significantly lower (P < 0.05) and drip loss was significantly higher (P < 0.05) than in the 700 Hz group. This study indicates that the waveform of the pulsed direct current is acceptable for stunning broilers at a stunning frequency of 700 Hz. © 2017 Poultry Science Association Inc.

Interactions between sanitizers and packaging gas compositions and their effects on the safety and quality of fresh-cut onions (Allium cepa L.).

PubMed

Page, Natalie; González-Buesa, Jaime; Ryser, Elliot T; Harte, Janice; Almenar, Eva

2016-02-02

Onions are one of the most widely utilized vegetables worldwide, with demand for fresh-cut onions steadily increasing. Due to heightened safety concerns and consumer demand, the implications of sanitizing and packaging on fresh-cut onion safety and quality need to be better understood. The objective of this study was to investigate the effect of produce sanitizers, in-package atmospheres, and their interactions on the growth of Salmonella Typhimurium, mesophilic aerobic bacteria, yeast and mold, and the physico-chemical quality of diced onions to determine the best sanitizer and in-package atmosphere combination for both safety and quality. Diced onions were inoculated or not with S. Typhimurium, sanitized in sodium hypochlorite, peroxyacetic acid, or liquid chlorine dioxide, and then packaged in either polylactic acid bags containing superatmospheric O2, elevated CO2/reduced O2, or air, or in polyethylene terephthalate snap-fit containers. Throughout 14 days of storage at 7 °C, packaged diced onions were assessed for their safety (S. Typhimurium), and quality (mesophilic aerobic bacteria, yeasts and molds, physico-chemical analyses, and descriptive and consumer acceptance sensory panels). While sanitizer affected (P<0.05) fewer parameters (S. Typhimurium, mesophiles, yeasts and molds, headspace CO2, weight loss, and pH), in-package atmosphere had a significant (P<0.05) effect on all parameters evaluated. Two-way interactions between sanitizer and atmosphere that affected S. Typhimurium and pH were identified whereas 3-way interactions (sanitizer, atmosphere and time) were only observed for headspace CO2. Sodium hypochlorite and elevated CO2/reduced O2 was the best sanitizer and in-package atmosphere combination for enhancing the safety and quality of packaged diced onions. In addition, this combination led to diced onions acceptable for purchase after 2 weeks of storage by trained and consumer panels. Copyright © 2015 Elsevier B.V. All rights reserved.

Evaluation of ultrasound based sterilization approaches in terms of shelf life and quality parameters of fruit and vegetable juices.

PubMed

Khandpur, Paramjeet; Gogate, Parag R

2016-03-01

The present work evaluates the performance of ultrasound based sterilization approaches for processing of different fruit and vegetable juices in terms of microbial growth and changes in the quality parameters during the storage. Comparison with the conventional thermal processing has also been presented. A novel approach based on combination of ultrasound with ultraviolet irradiation and crude extract of essential oil from orange peels has been used for the first time. Identification of the microbial growth (total bacteria and yeast content) in the juices during the subsequent storage and assessing the safety for human consumption along with the changes in the quality parameters (Brix, titratable acidity, pH, ORP, salt, conductivity, TSS and TDS) has been investigated in details. The optimized ultrasound parameters for juice sterilization were established as ultrasound power of 100 W and treatment time of 15 min for the constant frequency operation (20 kHz). It has been established that more than 5 log reduction was achieved using the novel combined approaches based on ultrasound. The treated juices using different approaches based on ultrasound also showed lower microbial growth and improved quality characteristics as compared to the thermally processed juice. Scale up studies were also performed using spinach juice as the test sample with processing at 5 L volume for the first time. The ultrasound treated juice satisfied the microbiological and physiochemical safety limits in refrigerated storage conditions for 20 days for the large scale processing. Overall the present work conclusively established the usefulness of combined treatment approaches based on ultrasound for maintaining the microbiological safety of beverages with enhanced shelf life and excellent quality parameters as compared to the untreated and thermally processed juices. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of Novel Quick Freezing Techniques Combined with Different Thawing Processes on Beef Quality

PubMed Central

Yoo, Seon-Mi; Han, Gui-Jung

2014-01-01

This study investigated the effect of various freezing and thawing techniques on the quality of beef. Meat samples were frozen using natural convection freezing (NF), individual quick freezing (IQF), or cryogenic freezing (CF) techniques, followed by natural convection thawing (NCT) or running water thawing (RT). The meat was frozen until the core temperature reached -12℃ and then stored at -24℃, followed by thawing until the temperature reached 5℃. Quality parameters, such as the pH, water binding properties, CIE color, shear force, and microstructure of the beef were elucidated. Although the freezing and thawing combinations did not cause remarkable changes in the quality parameters, rapid freezing, in the order of CF, IQF, and NF, was found to minimize the quality deterioration. In the case of thawing methods, NCT was better than RT and the meat quality was influence on the thawing temperature rather than the thawing rate. Although the microstructure of the frozen beef exhibited an excessive loss of integrity after the freezing and thawing, it did not cause any remarkable change in the beef quality. Taken together, these results demonstrate that CF and NCT form the best combination for beef processing; however, IQF and NCT may have practical applications in the frozen food industry. PMID:26761674

The quest for safe drinking water: an example from Guinea-Bissau (West Africa).

PubMed

Bordalo, Adriano A; Savva-Bordalo, Joana

2007-07-01

While humans require water for life, one-sixth of our species lives without access to safe water. In Africa, the situation is particularly acute because of global warming, the progression of the Sahara desert, civil unrest and poor governance, population growth, migration and poverty. In rural areas, the lack of adequate safe water and sanitary infrastructures leaves millions with doubtful water quality, increasing the harshness of daily life. In this paper, a pilot study was conducted during the wet season on Bolama Island (Guinea-Bissau, West Africa), a UNESCO Man and the Biosphere Reserve. Twenty-eight shallow wells, supplying water to most of the population, were sampled for microbiological, physical and chemical water quality characteristics. A ten-parameter water quality index (WQI) adapted to tropical conditions was applied to compare the different wells. About 79% of the wells showed moderate to heavy fecal contamination. From the surveyed parameters, it was found that chemical contamination was less important, although all samples were acidic, with the pH averaging 5.12+/-0.08. The WQI was 43+/-4% (0%-worst; 100%-best quality), showing that the water from the majority of wells was polluted but should be suitable for domestic use after appropriate treatment. At the onset of the wet season, diarrhea represented 11.5% of all medical cases, 92.5% of which were children aged <15. This paper suggests inexpensive steps to reduce the fecal contamination and control the pH in order to increase the potability of the well water and, concomitantly, to raise the living standards of the population in one of the poorest countries of the world.

Modulation of glycogen and breast meat processing ability by nutrition in chickens: effect of crude protein level in 2 chicken genotypes.

PubMed

Jlali, M; Gigaud, V; Métayer-Coustard, S; Sellier, N; Tesseraud, S; Le Bihan-Duval, E; Berri, C

2012-02-01

The aim of the study was to evaluate the impact of 2 isoenergetic growing diets with different CP (17 vs. 23%) on the performance and breast meat quality of 2 lines of chicken divergently selected for abdominal fatness [i.e., fat and lean (LL) lines]. Growth performance, breast and abdominal fat yields, breast meat quality parameters (pH, color, drip loss), and muscle glycogen storage at death were measured. Increased dietary CP resulted in increased BW, increased breast meat yield, and reduced abdominal fatness at slaughter regardless of genotype (P < 0.001). By contrast, dietary CP affected glycogen storage and the related meat quality parameters only in the LL chickens. Giving LL chickens the low-CP diet led to reduced concentration of muscle glycogen (P < 0.01), and as a result, breast meat with a higher (P < 0.001) ultimate pH, decreased (P < 0.001) lightness, and reduced (P < 0.001) drip loss during storage. The decreased muscle glycogen content observed in LL receiving the low-CP diet compared with the high-CP diet occurred concomitantly with greater phosphorylation amount for the α-catalytic subunit of adenosine monophosphate-activated protein kinase and glycogen synthase. This was consistent with the reduced muscle glycogen content observed in LL fed the low-CP diet because adenosine monophosphate-activated protein kinase inhibits glycogen synthesis through its action on glycogen synthase. Our results demonstrated that nutrition is an effective means of modulating breast meat properties in the chicken. The results also highlighted the need to take into account interaction with the genetic background of the animal to select nutritional strategies to improve meat quality traits in poultry.

Influence of water quality on nitrifier regrowth in two full-scale drinking water distribution systems.

PubMed

Scott, Daniel B; Van Dyke, Michele I; Anderson, William B; Huck, Peter M

2015-12-01

The potential for regrowth of nitrifying microorganisms was monitored in 2 full-scale chloraminated drinking water distribution systems in Ontario, Canada, over a 9-month period. Quantitative PCR was used to measure amoA genes from ammonia-oxidizing bacteria (AOB) and ammonia-oxidizing archaea (AOA), and these values were compared with water quality parameters that can influence nitrifier survival and growth, including total chlorine, ammonia, temperature, pH, and organic carbon. Although there were no severe nitrification episodes, AOB and AOA were frequently detected at low concentrations in samples collected from both distribution systems. A culture-based presence-absence test confirmed the presence of viable nitrifiers. AOB were usually present in similar or greater numbers than AOA in both systems. As well, AOB showed higher regrowth potential compared with AOA in both systems. Statistically significant correlations were measured between several water quality parameters of relevance to nitrification. Total chlorine was negatively correlated with both nitrifiers and heterotrophic plate count (HPC) bacteria, and ammonia levels were positively correlated with nitrifiers. Of particular importance was the strong correlation between HPC and AOB, which reinforced the usefulness of HPC as an operational parameter to measure general microbiological conditions in distribution systems.

Monitoring of urban and rural basins: water quality of Mourão basin.

PubMed

Passig, F H; Lima, S B; Carvalho, K Q; Halmeman, M C R; Souza, P C; Gusmão, L K

2015-12-01

The Mourão River basin is located on the central western region of the Paraná State - Brazil, between coordinates 23º 44' - 24º 25 South latitude and 52º 12' - 52º 30' West longitude, between 270 and 820 m above sea level, and 1,648.21 km2 drainage area. Water quality was evaluated by monitoring physical, chemical and microbiological parameters. Monthly samplings were performed for a year at five sites in the basin for analysis of: pH, temperature, dissolved oxygen, biochemical oxygen demand, total nitrogen, ammoniacal nitrogen, nitrite, nitrate, total phosphorus, turbidity, total solids, volatile solids and fecal coliforms. The results of the evaluated parameters showed higher values than the limits set by CONAMA Resolution 357 from 2005 for Class 2 in some samples. The Water Quality Index (WQI) indicated that 72% of samples had average quality and 28% had good quality for the Mourão River basin. Higher values of WQI were observed after rainfall period with median of 75 compared to the dry period with median of 62. The source of the Mourão River is contaminated with fecal coliforms, evidencing the real need to treat sewage in rural areas.

Automatic film processors' quality control test in Greek military hospitals.

PubMed

Lymberis, C; Efstathopoulos, E P; Manetou, A; Poudridis, G

1993-04-01

The two major military radiology installations (Athens, Greece) using a total of 15 automatic film processors were assessed using the 21-step-wedge method. The results of quality control in all these processors are presented. The parameters measured under actual working conditions were base and fog, contrast and speed. Base and fog as well as speed displayed large variations with average values generally higher than acceptable, whilst contrast displayed greater stability. Developer temperature was measured daily during the test and was found to be outside the film manufacturers' recommended limits in nine of the 15 processors. In only one processor did film passing time vary on an every day basis and this was due to maloperation. Developer pH test was not part of the daily monitoring service being performed every 5 days for each film processor and found to be in the range 9-12; 10 of the 15 processors presented pH values outside the limits specified by the film manufacturers.

Modelling lamb carcase pH and temperature decline parameters: relationship to shear force and abattoir variation.

PubMed

Hopkins, David L; Holman, Benjamin W B; van de Ven, Remy J

2015-02-01

Carcase pH and temperature decline rates influence lamb tenderness; therefore pH decline parameters are beneficial when modelling tenderness. These include pH at temperature 18 °C (pH@Temp18), temperature when pH is 6 (Temp@pH6), and pH at 24 h post-mortem (pH24). This study aimed to establish a relationship between shear force (SF) as a proxy for tenderness and carcase pH decline parameters estimated using both linear and spline estimation models for the m. longissimus lumborum (LL). The study also compared abattoirs regarding their achievement of ideal pH decline, indicative of optimal tenderness. Based on SF measurements of LL and m. semimembranosus collected as part of the Information Nucleus slaughter programme (CRC for Sheep Industry Innovation) this study found significant relationships between tenderness and pH24LL, consistent across the meat cuts and ageing periods examined. Achievement of ideal pH decline was shown not to have significantly differed across abattoirs, although rates of pH decline varied significantly across years within abattoirs.

Natural Fatigue Crack Initiation and Detection in High Quality Spur Gears

DTIC Science & Technology

2012-06-01

Natural Fatigue Crack Initiation and Detection in High Quality Spur Gears by David “Blake” Stringer, Ph.D., Kelsen E. LaBerge, Ph.D., Cory...0383 June 2012 Natural Fatigue Crack Initiation and Detection in High Quality Spur Gears David “Blake” Stringer and Ph.D., Kelsen E. LaBerge...Quality Spur Gears 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) David “Blake” Stringer, Ph.D., Kelsen E

Identification of regional soil quality factors and indicators: a case study on an alluvial plain (central Turkey)

NASA Astrophysics Data System (ADS)

Şeker, Cevdet; Hüseyin Özaytekin, Hasan; Negiş, Hamza; Gümüş, İlknur; Dedeoğlu, Mert; Atmaca, Emel; Karaca, Ümmühan

2017-05-01

Sustainable agriculture largely depends on soil quality. The evaluation of agricultural soil quality is essential for economic success and environmental stability in rapidly developing regions. In this context, a wide variety of methods using vastly different indicators are currently used to evaluate soil quality. This study was conducted in one of the most important irrigated agriculture areas of Konya in central Anatolia, Turkey, to analyze the soil quality indicators of Çumra County in combination with an indicator selection method, with the minimum data set using a total of 38 soil parameters. We therefore determined a minimum data set with principle component analysis to assess soil quality in the study area and soil quality was evaluated on the basis of a scoring function. From the broad range of soil properties analyzed, the following parameters were chosen: field capacity, bulk density, aggregate stability, and permanent wilting point (from physical soil properties); electrical conductivity, Mn, total nitrogen, available phosphorus, pH, and NO3-N (from chemical soil properties); and urease enzyme activity, root health value, organic carbon, respiration, and potentially mineralized nitrogen (from biological properties). According to the results, the chosen properties were found as the most sensitive indicators of soil quality and they can be used as indicators for evaluating and monitoring soil quality at a regional scale.

Quality evaluation and in vitro interaction studies between levofloxacin 250mg and diclofenac sodium 50mg tablets.

PubMed

Fayyaz, Muhammad; Yousuf, Rabia Ismail; Shoaib, Muhammad Harris; Ali, Tariq; Nasiri, Iqbal; Ashraf, Nida

2015-01-01

Fluoroquinolones are broad-spectrum antibiotics, work against Gram-positive and Gram-negative bacteria and are a clinically proven option for many resistant infections. Among fluoroquinolones Levofloxacin works best against acute sinusitis, inflammation of the lower airways, acute exacerbation of chronic bronchitis, community acquired pneumonia, complicated urinary tract infection including Pyelonephritis, chronic bacterial prostatitis and skin and soft tissue infection. Levofloxacin is a frequently prescribed antibacterial agent with Diclofenac Sodium for pain management in infectious conditions. The objective of the present work is to evaluate the level of interaction between Levofloxacin and Diclofenac Sodium. In this work market available brands of both drugs were also evaluated for quality.The physiochemical parameters like weight variation, thickness variation, and mechanical strength were determined. Similarly the percentage drug release and content uniformity test were also analyzed; the tested quality attributes were found within the recommended pharmacopeia ranges except brand L(6) that had high drug content 124.629±3.614 while brand L(4) and L(5) were not found similar in pH 1.2. When subjected to model dependent analysis Levofloxacin showed compliance with (first order, Higuchi, Hixson Crowell and Weibull) at pH (1.2, 4.5 and 6.8). However Diclofenac Sodium showed adherence with (first order, Hixson Crowell and Weibull) at pH (1.2, 4.5 and 6.8) but following Higuchi at pH 1.2 and 4.5 only. The interaction studies were also performed spectrophotometrically and simultaneous equation was used to estimate the percentage availability of both the drugs at pH 4.5, 6.8, FaSSGF and FaSSIF. The studies showed that the percent availability of Levofloxacin was increased significantly in FaSSIF i.e. 129.173±0.323 at 45 minutes in the presence of Diclofenac Sodium.

Seasonal microbial and environmental parameters at Crocker Reef, Florida Keys, 2014–2015

USGS Publications Warehouse

Kellogg, Christina A.; Yates, Kimberly K.; Lawler, Stephanie N.; Moore, Christopher S.; Smiley, Nathan A.

2015-11-04

Microbial measurements included enumeration of total bacteria, enumeration of virus-like particles, and plate counts of Vibrio spp. colony-forming units (CFU). These measurements were intended to give a sense of any seasonal changes in the total microbial load and to provide an indication of water quality. Additional environmental parameters measured included water temperature, salinity, dissolved oxygen, and pH. Four sites (table 1) were intensively sampled for periods of approximately 48 hours during summer (July 2014) and winter (January–February 2015), during which water samples were collected every 4 hours for analysis, except when prevented by weather conditions.

Evaluation of Low-Temperature Phosphine Fumigation for Control of Oriental Fruit Fly in Loquat Fruit.

PubMed

Liu, Tao; Li, Li; Li, Baishu; Zhan, Guoping; Wang, Yuejin

2018-05-28

Oriental fruit fly, Bactrocera dorsalis (Hendel; Diptera: Tephritidae), is recognized as a quarantine pest and a threat to Chinese loquat (Eriobotrya japonica Lindl.) fruit exports. Since loquat fruit is very sensitive to methyl bromide (MB) fumigation and cold treatment, in this study, low-temperature phosphine (PH3) fumigation was investigated to develop an alternative phytosanitary treatment method. Tolerance tests showed that the third instar was the most tolerant of all life stages of B dorsalis to PH3 gas at 8°C. Toxicity assay with 500-3000 ppm PH3 and subsequent probit analysis showed that 2000 ppm PH3 was optimal for fumigation and 152.75 h of treatment duration were required to achieve 99.9968% mortality. In the verification test, 144 and 168 h of treatment duration with 2000 ppm PH3 completely killed 35,277 and 35,134 B. dorsalis third instars, respectively. However, 13 live larvae were found after 120 h of treatment. Furthermore, these treatments reduced fruit respiration rates while causing no adverse effects on other fruit quality parameters, including firmness, soluble solid content, and titratable acidity over 192 h storage at 8°C. The results strongly suggest that low-temperature PH3 fumigation could be used for the postharvest control of B. dorsalis in loquat fruit.

Temporal variability in water quality parameters--a case study of drinking water reservoir in Florida, USA.

PubMed

Toor, Gurpal S; Han, Lu; Stanley, Craig D

2013-05-01

Our objective was to evaluate changes in water quality parameters during 1983-2007 in a subtropical drinking water reservoir (area: 7 km(2)) located in Lake Manatee Watershed (area: 338 km(2)) in Florida, USA. Most water quality parameters (color, turbidity, Secchi depth, pH, EC, dissolved oxygen, total alkalinity, cations, anions, and lead) were below the Florida potable water standards. Concentrations of copper exceeded the potable water standard of <30 μg l(-1) in about half of the samples. About 75 % of total N in lake was organic N (0.93 mg l(-1)) with the remainder (25 %) as inorganic N (NH3-N: 0.19, NO3-N: 0.17 mg l(-1)), while 86 % of total P was orthophosphate. Mean total N/P was <6:1 indicating N limitation in the lake. Mean monthly concentration of chlorophyll-a was much lower than the EPA water quality threshold of 20 μg l(-1). Concentrations of total N showed significant increase from 1983 to 1994 and a decrease from 1997 to 2007. Total P showed significant increase during 1983-2007. Mean concentrations of total N (n = 215; 1.24 mg l(-1)) were lower, and total P (n = 286; 0.26 mg l(-1)) was much higher than the EPA numeric criteria of 1.27 mg total N l(-1) and 0.05 mg total P l(-1) for Florida's colored lakes, respectively. Seasonal trends were observed for many water quality parameters where concentrations were typically elevated during wet months (June-September). Results suggest that reducing transport of organic N may be one potential option to protect water quality in this drinking water reservoir.

An assessment of quality of water from boreholes in Bindura District, Zimbabwe

NASA Astrophysics Data System (ADS)

Hoko, Zvikomborero

This study assessed the water quality of 144 boreholes in Bindura District in Mashonaland Province of Zimbabwe as part of a borehole rehabilitation project implemented by a local NGO. In previous studies it has been observed that some boreholes are not used for domestic purposes because of consumer perceived poor water quality. Consequently, communities have resorted to unsafe alternative water sources thus creating health risks. The study was carried out in June 2005. The objectives of the study were to assess the levels of parameters associated with the aesthetics of the water and to compare them with guideline values for drinking water. The study also investigated the relationship between some of the measured water quality and the consumer perceived water quality. Measured water quality parameters included pH, temperature, electrical conductivity (EC), turbidity, calcium (Ca), magnesium (Mg) and iron (Fe). All parameters were measured in the field except Ca, Mg and Fe, which were measured in a laboratory using a spectrophotometer. Consumer perceptions on water quality were investigated through interviews with the consumer community. Turbidity was found to be 0.75-428(20.8 ± 59.2; n = 144) NTU, pH 5.7-9.3 (6.88 ± 0.46; n = 144), temperature 18-26.8 (22.6 ± 2.1; n = 144) °C. EC 26-546 (199 ± 116; n = 144) μS/cm, Ca 6-71.6 (26.9 ± 14.1; n = 81) mg/l, Mg 1.2-49.6 (12.3 ± 10.0; n = 81) mg/l and Fe 0.08-9.60 (0.56 ± 1.15; n = 81) mg/l. Some 23% of the samples had pH outside the recommended range of 6.5-8.5, whilst 59% of the samples had turbidity values exceeding the 5NTU WHO limit. For EC, all samples had values less than the WHO derived limit of 1380 μS/cm. All Ca and magnesium values were within the common and recommended levels of 100 mg/l and 70 mg/l respectively. Iron had values greater than the WHO and SAZ limit of 0.3 mg/l in 36% of the samples. Water quality was deemed satisfactory for taste and soap consumption by 95% and 72% of the respondents respectively. Satisfaction was higher for drinking compared to soap consumption meaning that generally hard waters may still be acceptable for drinking purposes. The water quality met the stipulated standard or guideline value from a minimum of 41% (turbidity) to a maximum of 100% (EC, Ca and Mg). There was no correlation between taste and conductivity as some 5% of the respondents suggested the water was unsatisfactory although all EC values were far below the maximum limit. Again there was no correlation between iron and taste as iron had 36% of the samples above the threshold of 0.3 mg/l whilst objectionable taste perception was only in 5% of the cases. It is recommended that priority in future projects should be given to repairs of boreholes whose water quality is acceptable according to consumer perceptions obtained at project planning stage. Low cost household treatment aimed at improving quality should be investigated.

Prevalence and distribution of Aeromonas hydrophila in the United States.

PubMed

Hazen, T C; Fliermans, C B; Hirsch, R P; Esch, G W

1978-11-01

The abundance of Aeromonas hydrophila was measured in 147 natural aquatic habitats in 30 states and Puerto Rico. Viable cell counts were used to estimate density at all sites by using Rimler-Shotts medium, a differential presumptive medium for A. hydrophila. Temperature, pH, conductivity, salinity, and turbidity were measured simultaneously with water sample collection. The density of A. hydrophila was higher in lotic than in lentic systems. Saline systems had higher densities of A. hydrophila than did freshwater systems. A. hydrophila could not be isolated from extremely saline, thermal, or polluted waters, even though it was found over wide ranges of salinity, conductivity, temperature, pH, and turbidity. Of the water quality parameters measured, only conductivity was significantly regressed with density of A. hydrophila.

Effects of Urbanization on Stream Water Quality in the City of Atlanta, Georgia, USA

NASA Astrophysics Data System (ADS)

Peters, N. E.

2009-05-01

A long-term stream water-quality monitoring network was established in the City of Atlanta (COA) during 2003 to assess baseline water-quality conditions and the effects of urbanization on stream water quality. Routine hydrologically-based manual stream sampling, including several concurrent manual point and equal width increment sampling, was conducted approximately 12 times per year at 21 stations, with drainage areas ranging from 3.7 to 232 km2. Eleven of the stations are real-time (RT) water-quality stations having continuous measures of stream stage/discharge, pH, dissolved oxygen, specific conductance, water temperature, and turbidity, and automatic samplers for stormwater collection. Samples were analyzed for field parameters, and a broad suite of water-quality and sediment-related constituents. This paper summarizes an evaluation of field parameters and concentrations of major ions, minor and trace metals, nutrient species (nitrogen and phosphorus), and coliform bacteria among stations and with respect to watershed characteristics and plausible sources from 2003 through September 2007. The concentrations of most constituents in the COA streams are statistically higher than those of two nearby reference streams. Concentrations are statistically different among stations for several constituents, despite high variability both within and among stations. The combination of routine manual sampling, automatic sampling during stormflows, and real-time water-quality monitoring provided sufficient information about the variability of urban stream water quality to develop hypotheses for causes of water-quality differences among COA streams. Fecal coliform bacteria concentrations of most individual samples at each station exceeded Georgia's water-quality standard for any water-usage class. High chloride concentrations occur at three stations and are hypothesized to be associated with discharges of chlorinated combined sewer overflows, drainage of swimming pool(s), and dissolution and transport during rainstorms of CaCl2, a deicing salt applied to roads during winter storms. Water quality of one stream was highly affected by the dissolution and transport of ammonium alum [NH4Al(SO4)2] from an alum manufacturing plant in the watershed; streamwater has low pH (<5), low alkalinity and high concentrations of minor and trace metals. Several trace metals (Cu, Pb and Zn) exceed acute and chronic water-quality standards and the high concentrations are attributed to washoff from impervious surfaces.

Effect of biochars produced from solid organic municipal waste on soil quality parameters.

PubMed

Randolph, P; Bansode, R R; Hassan, O A; Rehrah, Dj; Ravella, R; Reddy, M R; Watts, D W; Novak, J M; Ahmedna, M

2017-05-01

New value-added uses for solid municipal waste are needed for environmental and economic sustainability. Fortunately, value-added biochars can be produced from mixed solid waste, thereby addressing solid waste management issues, and enabling long-term carbon sequestration. We hypothesize that soil deficiencies can be remedied by the application of municipal waste-based biochars. Select municipal organic wastes (newspaper, cardboard, woodchips and landscaping residues) individually or in a 25% blend of all four waste streams were used as feedstocks of biochars. Three sets of pyrolysis temperatures (350, 500, and 750 °C) and 3 sets of pyrolysis residence time (2, 4 and 6 h) were used for biochar preparation. The biochar yield was in the range of 21-62% across all feedstocks and pyrolysis conditions. We observed variations in key biochar properties such as pH, electrical conductivity, bulk density and surface area depending on the feedstocks and production conditions. Biochar increased soil pH and improved its electrical conductivity, aggregate stability, water retention and micronutrient contents. Similarly, leachate from the soil amended with biochar showed increased pH and electrical conductivity. Some elements such as Ca and Mg decreased while NO 3 -N increased in the leachates of soils incubated with biochars. Overall, solid waste-based biochar produced significant improvements to soil fertility parameters indicating that solid municipal wastes hold promising potential as feedstocks for manufacturing value-added biochars with varied physicochemical characteristics, allowing them to not only serve the needs for solid waste management and greenhouse gas mitigation, but also as a resource for improving the quality of depleted soils. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determination of aluminium and physicochemical parameters in the palm oil estates water supply at Johor, Malaysia.

PubMed

Siti Farizwana, M R; Mazrura, S; Zurahanim Fasha, A; Ahmad Rohi, G

2010-01-01

The study was to determine the concentration of aluminium (Al) and study the physicochemical parameters (pH, total dissolved solids (TDS), turbidity, and residual chlorine) in drinking water supply in selected palm oil estates in Kota Tinggi, Johor. Water samples were collected from the estates with the private and the public water supplies. The sampling points were at the water source (S), the treatment plant outlet (TPO), and at the nearest houses (H1) and the furthest houses (H2) from the TPO. All estates with private water supply failed to meet the NSDWQ for Al with mean concentration of 0.99 ± 1.52 mg/L. However, Al concentrations in all public water supply estates were well within the limit except for one estate. The pH for all samples complied with the NSDWQ except from the private estates for the drinking water supply with an acidic pH (5.50 ± 0.90). The private water supply showed violated turbidity value in the drinking water samples (14.2 ± 24.1 NTU). Insufficient amount of chlorination was observed in the private water supply estates (0.09 ± 0.30 mg/L). Private water supplies with inefficient water treatment served unsatisfactory drinking water quality to the community which may lead to major health problems.

Zn (II) Removal from River Water Samples of Sembrong, Johor State, Malaysia by Electrokinetic Remediation

NASA Astrophysics Data System (ADS)

Zaidi, E.; Husna, MNF; Shakila, A.; Azhar, ATS; Arif, AM; Norshuhaila, MS

2017-08-01

Heavy metals pollution has become one of the most serious environmental problems today. The treatment of heavy metals is of special concern due to their recalcitrance and persistence in the environment. Even many physical, chemical and biological treatment processes have been proposed to remove heavy metals from river water, the use of these treatment processes are not efficient and relatively costly. This study focused on the potential application of electrokinetic (EK) remediation in Sembrong River water to remove zinc (Zn2+). The physicochemical and biological parameters and water quality index (WQI) of Sembrong River water was characterized. The electrokinetic remediation experiments were performed by controlling pH, and electric density on voltage were observed and investigated. The results indicated that all physicochemical and biological parameters of Sembrong River complied with the standard discharged limit set by the Department of Environment (DOE). However, suspended solids (SS) and pH can be categorized as Class III according to INWQS. The best performance of 88% efficiency of zinc can be achieved EK experiment run at a fixed voltage of 30 V at pH 5.14 after 60 min of the process operate. This technology may be proposed for faster and eco-friendly removal of heavy metals in the environment.

Portuguese Honeys from Different Geographical and Botanical Origins: A 4-Year Stability Study Regarding Quality Parameters and Antioxidant Activity.

PubMed

Soares, Sonia; Pinto, Diana; Rodrigues, Francisca; Alves, Rita C; Oliveira, M Beatriz P P

2017-08-11

Portuguese honeys (n = 15) from different botanical and geographical origins were analysed regarding their quality parameters (diastase activity, hydroxymethylfurfural content, moisture and pH), colour (L*, a*, b*) and antioxidant profile (total phenolics content, total flavonoids content, DPPH• scavenging activity, and ferric reducing power). The samples were analysed fresh and after 4-years of storage (at 25 °C and protected from light). The hydroxymethylfurfural content and diastase activity of the fresh samples were in accordance with the recommended values described in the legislation. In general, the antioxidant activity of the samples correlated more with the bioactive compounds content than with colour. The storage affected differently each individual sample, especially regarding the antioxidant profile. Nevertheless, although in general the lightness of the samples decreased (and the redness increased), after 4 years, 11 samples still presented acceptable diastase activity and hydroxymethylfurfural values.

Effects of coating chitosan inhibition to quality of fish fillet Oreochromis niloticus at room temperature storage

NASA Astrophysics Data System (ADS)

Saputra, Eka; Tjahjaningsih, Wahju; Patmawati

2017-02-01

Fresh fish shelf life can be extended by adding antibacterial compounds such as synthetic chemicals or natural materials. One of the natural ingredients that are safe to use to prolong the freshness of the fish is chitosan. Chitosan is able to provide quality deterioration inhibitory effect of fillet of tilapia. The rate of decline in the value of organoleptic fillet of tilapia treated chitosan solution is slower when compared to no treatment tilapia fillet chitosan solution. In the organoleptic test until the 18 hours of storage, 2% chitosan solution capable of maintaining the highest organoleptic value for the parameter sightings meat, texture, and smell fillet. The use of 2% chitosan solution provided the best results based on the parameters of the appearance of meat, the texture, the smell, the pH value and the value of TVB fillet.

Theoretical technique for predicting the cumulative impact of iron and manganese oxidation in streams receiving discharge from coal mines

USGS Publications Warehouse

Bobay, Keith E.

1986-01-01

Two U.S. Geological Survey computer programs are modified and linked to predict the cumulative impact of iron and manganese oxidation in coal-mine discharge water on the dissolved chemical quality of a receiving stream. The coupled programs calculate the changes in dissolved iron, dissolved manganese, and dissolved oxygen concentrations; alkalinity; and, pH of surface water downstream from the point of discharge. First, the one-dimensional, stead-state stream, water quality program uses a dissolved oxygen model to calculate the changes in concentration of elements as a function of the chemical reaction rates and time-of-travel. Second, a program (PHREEQE) combining pH, reduction-oxidation potential, and equilibrium equations uses an aqueous-ion association model to determine the saturation indices and to calculate pH; it then mixes the discharge with a receiving stream. The kinetic processes of the first program dominate the system, whereas the equilibrium thermodynamics of the second define the limits of the reactions. A comprehensive test of the technique was not possible because a complete set of data was unavailable. However, the cumulative impact of representative discharges from several coal mines on stream quality in a small watershed in southwestern Indiana was simulated to illustrate the operation of the technique and to determine its sensitivity to changes in physical, chemical, and kinetic parameters. Mine discharges averaged 2 cu ft/sec, with a pH of 6.0, and concentrations of 7.0 mg/L dissolved iron, 4.0 mg/L dissolved manganese, and 8.08 mg/L dissolved oxygen. The receiving stream discharge was 2 cu ft/sec, with a pH of 7.0, and concentrations of 0.1 mg/L dissolved iron, 0.1 mg/L dissolved manganese, and 8.70 mg/L dissolved oxygen. Results of the simulations indicated the following cumulative impact on the receiving stream from five discharges as compared with the effect from one discharge: 0.30 unit decrease in pH, 1.82 mg/L increase in dissolved iron, 1.50 mg/L increase in dissolved manganese, and 0.24 mg/L decrease in dissolved oxygen concentration.

Characterization of water treatment sludge and its reuse as coagulant.

PubMed

Ahmad, Tarique; Ahmad, Kafeel; Ahad, Abdul; Alam, Mehtab

2016-11-01

Coagulation-flocculation process results in the generation of large volume of waste or residue, known as water treatment sludge (WTS), in the purification of surface water for potable supplies. Sustainable management of the inevitable waste requires careful attention from the plant operators and sludge managers. In this study, WTS produced with the optimum alum dose of 30 ml/L at the laboratory scale has been treated with sulphuric acid to bring forth a product known as sludge reagent product (SRP). The performance of SRP is evaluated for its efficiency in removing the colloidal suspensions from the Yamuna river water over wide pH range of 2-13. 1% sludge acidified with sulphuric acid of normality 2.5 at the rate of 0.05 ml/ml sludge has been observed as the optimum condition for preparing SRP from WTS. The percentage turbidity removal is greater at higher pH value and increases with increasing the dosage of SRP. The optimum SRP dosage of 8 ml/L in the pH range of 6-8 performed well in removing the colloidal suspension and other impurities from the Yamuna water. The quality of treated water met the prescribed standards for most of the quality parameters. Thus, SRP has the potential to substitute the conventional coagulants partially or completely in the water treatment process, depending on the quality needed at the users end. Copyright © 2016 Elsevier Ltd. All rights reserved.

Synthesis of hydroxyapatite nanorods for application in water defluoridation and optimization of process variables: Advantage of ultrasonication with precipitation method over conventional method.

PubMed

Mehta, Dhiraj; Mondal, Poonam; Saharan, Virendra Kumar; George, Suja

2017-07-01

This research work presents the synthesis of hydroxyapatite (Hap) nanorods for defluoridation of drinking water by using both conventional (CM) and ultrasonication with precipitation (USPM) methods. Calcium nitrate was reacted with potassium phosphate in presence of ammonia for controlled pH to synthesize Hap nanorods, which was characterized using FTIR, XRD, SEM, TG-DTA, and TEM/EDS for determining its phase composition, structural and thermal decomposition behavior. When USPM method was used for synthesis, the yield of the Hap nanorods was improved from 83.24±1.0% to 90.2±1.0%, and complete phase transformation occurred with formation of elongated Hap nanorods. Effects of process parameters such as solution pH, contact time and adsorbent dose were studied through response surface methodology (RSM). A simple quadratic model was developed using Central Composite Design (CCD) and optimum parameters for fluoride adsorption process were determined to be pH 7, contact time 3h and adsorbent dose 7g/L for maximum removal capacity. Fluoride removal efficiency was predicted to be 93.64% which was very close to the experimental value obtained at 92.86% using ultrasonically prepared Hap. Fluoride adsorption isotherms fitted the Freundlich isotherm with an adsorption capacity of 1.49mg/g, while the kinetic studies revealed that the process followed pseudo-second order model. The treated water quality parameters such as residual fluoride, calcium leached, total hardness and alkalinity was investigated, and it was observed that all these parameters were within the permissible limits as per WHO and BIS standards. Copyright © 2017 Elsevier B.V. All rights reserved.

Impact of land-use on groundwater quality: GIS-based study from an alluvial aquifer in the western Ganges basin

NASA Astrophysics Data System (ADS)

Khan, Arina; Khan, Haris Hasan; Umar, Rashid

2017-12-01

In this study, groundwater quality of an alluvial aquifer in the western Ganges basin is assessed using a GIS-based groundwater quality index (GQI) concept that uses groundwater quality data from field survey and laboratory analysis. Groundwater samples were collected from 42 wells during pre-monsoon and post-monsoon periods of 2012 and analysed for pH, EC, TDS, Anions (Cl, SO4, NO3), and Cations (Ca, Mg, Na). To generate the index, several parameters were selected based on WHO recommendations. The spatially variable grids of each parameter were modified by normalizing with the WHO standards and finally integrated into a GQI grid. The mean GQI values for both the season suggest good groundwater quality. However, spatial variations exist and are represented by GQI map of both seasons. This spatial variability was compared with the existing land-use, prepared using high-resolution satellite imagery available in Google earth. The GQI grids were compared to the land-use map using an innovative GIS-based method. Results indicate that the spatial variability of groundwater quality in the region is not fully controlled by the land-use pattern. This probably reflects the diffuse nature of land-use classes, especially settlements and plantations.

Quality of semen: a 6-year single experience study on 5680 patients.

PubMed

Cozzolino, Mauro; Coccia, Maria E; Picone, Rita

2018-02-08

The aim of our study was to evaluate the quality of semen of a large sample from general healthy population living in Italy, in order to identify possible variables that could influence several parameters of spermiogram. We conducted a cross-sectional study from February 2010 to March 2015, collecting semen samples from the general population. Semen analysis was performed according to the WHO guidelines. The collected data were inserted in a database and processed using the software Stata 12. The Mann - Whitney test was used to assess the relationship of dichotomus variables with the parameters of the spermiogram; Kruskal-Wallis test for variables with more than two categories. We used also Robust regression and Spearman correlation to analyze the relationship between age and the parameters. We collected 5680 samples of semen. The mean age of our patients was 41.4 years old. Mann-Whitney test showed that the citizenship (codified as "Italian/Foreign") influences some parameters: pH, vitality, number of spermatozoa, sperm concentration, with worse results for the Italian group. Kruskal-Wallis test showed that the single nationality influences pH, volume, Sperm motility A-B-C-D, vitality, morphology, number of spermatozoa, sperm concentration. Robust regression showed a relationship between age and several parameters: volume (p=0.04, R squared= 0.0007 β: - 0.06); sperm motility A (p<0.01; R squared 0.0051 β: 0.02); sperm motility B (p<0.01; R squared 0.02 β: -0.35); sperm motility C (p<0.01; R squared 0.01 β: 0.12); sperm motility D (p<0.01; R squared 0.006 β: 0.2); vitality (p<0.01; R squared 0.01 β: -0.32); sperm concentration (p=0.01; R squared 0.001 β: 0.19). Our patients had spermiogram's results quite better than the standard guidelines. Our study showed that the country of origin could be a factor influencing several parameters of the spermiogram in healthy population and through Robust regression confirmed a strict correlation between age and these parameters.

Climate-water quality relationships in Texas reservoirs

USGS Publications Warehouse

Gelca, Rodica; Hayhoe, Katharine; Scott-Fleming, Ian; Crow, Caleb; Dawson, D.; Patino, Reynaldo

2015-01-01

Water temperature, dissolved oxygen, and concentrations of salts in surface water bodies can be affected by the natural environment, local human activities such as surface and ground water withdrawals, land use, and energy extraction, and variability and long-term trends in atmospheric conditions including temperature and precipitation. Here, we quantify the relationship between 121 indicators of mean and extreme temperature and precipitation and 24 water quality parameters in 57 Texas reservoirs using observational data records covering the period 1960 to 2010. We find that water temperature, dissolved oxygen, pH, specific conductance, chloride, sulfate, and phosphorus all show consistent correlations with atmospheric predictors, including high and low temperature extremes, dry days, heavy precipitation events, and mean temperature and precipitation over time scales ranging from one week to two years. Based on this analysis and published future projections for this region, we expect climate change to increase water temperatures, decrease dissolved oxygen levels, decrease pH, increase specific conductance, and increase levels of sulfate, chloride in Texas reservoirs. Over decadal time scales, this may affect aquatic ecosystems in the reservoirs, including altering the risk of conditions conducive to algae occurrence, as well as affecting the quality of water available for human consumption and recreation.

The Semen pH Affects Sperm Motility and Capacitation.

PubMed

Zhou, Ji; Chen, Li; Li, Jie; Li, Hongjun; Hong, Zhiwei; Xie, Min; Chen, Shengrong; Yao, Bing

2015-01-01

As the chemical environment of semen can have a profound effect on sperm quality, we examined the effect of pH on the motility, viability and capacitation of human sperm. The sperm in this study was collected from healthy males to avoid interference from other factors. The spermatozoa cultured in sperm nutrition solution at pH 5.2, 6.2, 7.2 and 8.2 were analyzed for sperm total motility, progressive motility (PR), hypo-osmotic swelling (HOS) rate, and sperm penetration. Our results showed that these parameters were similar in pH 7.2 and 8.2 sperm nutrition solutions, but decreased in pH 5.2 and 6.2 solutions. The HOS rate exhibited positive correlation with the sperm total motility and PR. In addition, the sperm Na(+)/K(+)-ATPase activity at different pHs was measured, and the enzyme activity was significantly lower in pH 5.2 and 6.2 media, comparing with that in pH 8.2 and pH 7.2 solutions. Using flow cytometry (FCM) and laser confocal scanning microscopy (LCSM) analysis, the intracellular Ca2(+ )concentrations of sperm cultured in sperm capacitation solution at pH 5.2, 6.2, 7.2 and 8.2 were determined. Compared with that at pH 7.2, the mean fluorescence intensity of sperm in pH 5.2 and 6.2 media decreased significantly, while that of pH 8.2 group showed no difference. Our results suggested that the declined Na(+)/K(+)-ATPase activity at acidic pHs result in decreased sperm movement and capacitation, which could be one of the mechanisms of male infertility.

Measurement of pH micro-heterogeneity in natural cheese matrices by fluorescence lifetime imaging

PubMed Central

Burdikova, Zuzana; Svindrych, Zdenek; Pala, Jan; Hickey, Cian D.; Wilkinson, Martin G.; Panek, Jiri; Auty, Mark A. E.; Periasamy, Ammasi; Sheehan, Jeremiah J.

2015-01-01

Cheese, a product of microbial fermentation may be defined as a protein matrix entrapping fat, moisture, minerals and solutes as well as dispersed bacterial colonies. The growth and physiology of bacterial cells in these colonies may be influenced by the microenvironment around the colony, or alternatively the cells within the colony may modify the microenvironment (e.g., pH, redox potential) due to their metabolic activity. While cheese pH may be measured at macro level there remains a significant knowledge gap relating to the degree of micro-heterogeneity of pH within the cheese matrix and its relationship with microbial, enzymatic and physiochemical parameters and ultimately with cheese quality, consistency and ripening patterns. The pH of cheese samples was monitored both at macroscopic scale and at microscopic scale, using a non-destructive microscopic technique employing C-SNARF-4 and Oregon Green 488 fluorescent probes. The objectives of this work were to evaluate the suitability of these dyes for microscale pH measurements in natural cheese matrices and to enhance the sensitivity and extend the useful pH range of these probes using fluorescence lifetime imaging (FLIM). In particular, fluorescence lifetime of Oregon Green 488 proved to be sensitive probe to map pH micro heterogeneity within cheese matrices. Good agreement was observed between macroscopic scale pH measurement by FLIM and by traditional pH methods, but in addition considerable localized microheterogeneity in pH was evident within the curd matrix with pH range between 4.0 and 5.5. This technique provides significant potential to further investigate the relationship between cheese matrix physico-chemistry and bacterial metabolism during cheese manufacture and ripening. PMID:25798136

Measurement of pH micro-heterogeneity in natural cheese matrices by fluorescence lifetime imaging.

PubMed

Burdikova, Zuzana; Svindrych, Zdenek; Pala, Jan; Hickey, Cian D; Wilkinson, Martin G; Panek, Jiri; Auty, Mark A E; Periasamy, Ammasi; Sheehan, Jeremiah J

2015-01-01

Cheese, a product of microbial fermentation may be defined as a protein matrix entrapping fat, moisture, minerals and solutes as well as dispersed bacterial colonies. The growth and physiology of bacterial cells in these colonies may be influenced by the microenvironment around the colony, or alternatively the cells within the colony may modify the microenvironment (e.g., pH, redox potential) due to their metabolic activity. While cheese pH may be measured at macro level there remains a significant knowledge gap relating to the degree of micro-heterogeneity of pH within the cheese matrix and its relationship with microbial, enzymatic and physiochemical parameters and ultimately with cheese quality, consistency and ripening patterns. The pH of cheese samples was monitored both at macroscopic scale and at microscopic scale, using a non-destructive microscopic technique employing C-SNARF-4 and Oregon Green 488 fluorescent probes. The objectives of this work were to evaluate the suitability of these dyes for microscale pH measurements in natural cheese matrices and to enhance the sensitivity and extend the useful pH range of these probes using fluorescence lifetime imaging (FLIM). In particular, fluorescence lifetime of Oregon Green 488 proved to be sensitive probe to map pH micro heterogeneity within cheese matrices. Good agreement was observed between macroscopic scale pH measurement by FLIM and by traditional pH methods, but in addition considerable localized microheterogeneity in pH was evident within the curd matrix with pH range between 4.0 and 5.5. This technique provides significant potential to further investigate the relationship between cheese matrix physico-chemistry and bacterial metabolism during cheese manufacture and ripening.

Impact of Red Water System (RWS) application on water quality of catfish culture using aquaponics

NASA Astrophysics Data System (ADS)

Zahidah; Dhahiyat, Y.; Andriani, Y.; Sahidin, A.; Farizi, I.

2018-03-01

This study aim was to analyze the effect of Red Water System (RWS) probiotics application on water quality in aquaponic system. The research used experimental method using Completely Randomized Design (CRD) with five treatments and three replications. Treatment A: RWS 7.5 μL·L-1/week without aquaponic probiotic, Treatment B: aquaponic without RWS probiotics, treatment C: RWS probiotic addition in aquaponic media at 7.5 μL·L-1/week, treatment D: addition of RWS probiotics in aquaponic media at 10 μL·L-1/week and treatment E: addition of RWS probiotics in in aquaponic media at 12.8 μL·L-1/week. Parameters measured were pH, temperature, ammonia, nitrate and phosphate. The results showed that water temperature and pH relatively unchanged in all treatments. The addition of RWS probiotics did not improve the concentration of ammonia, nitrate and phosphate. In fact, the catfish culture with only aquaponic resulted lower concentration of ammonia, nitrate and phosphate than other treatment. The lowest value of ammonia, nitrate and phosphates was obtained in the experimental groups of aquaponic with RWS of 10 μL·L-1/week (Treatment D). Treatment D has the lowest average ammonia of 0.50 ppm, reduced nitrate up to 60.78 % and temperature and pH relatively unchanged.

The influence of pH adjustment on kinetics parameters in tapioca wastewater treatment using aerobic sequencing batch reactor system

NASA Astrophysics Data System (ADS)

Mulyani, Happy; Budianto, Gregorius Prima Indra; Margono, Kaavessina, Mujtahid

2018-02-01

The present investigation deals with the aerobic sequencing batch reactor system of tapioca wastewater treatment with varying pH influent conditions. This project was carried out to evaluate the effect of pH on kinetics parameters of system. It was done by operating aerobic sequencing batch reactor system during 8 hours in many tapioca wastewater conditions (pH 4.91, pH 7, pH 8). The Chemical Oxygen Demand (COD) and Mixed Liquor Volatile Suspended Solids (MLVSS) of the aerobic sequencing batch reactor system effluent at steady state condition were determined at interval time of two hours to generate data for substrate inhibition kinetics parameters. Values of the kinetics constants were determined using Monod and Andrews models. There was no inhibition constant (Ki) detected in all process variation of aerobic sequencing batch reactor system for tapioca wastewater treatment in this study. Furthermore, pH 8 was selected as the preferred aerobic sequencing batch reactor system condition in those ranging pH investigated due to its achievement of values of kinetics parameters such µmax = 0.010457/hour and Ks = 255.0664 mg/L COD.

Asymmetric 2D spatial beam filtering by photonic crystals

NASA Astrophysics Data System (ADS)

Gailevicius, D.; Purlys, V.; Maigyte, L.; Gaizauskas, E.; Peckus, M.; Gadonas, R.; Staliunas, K.

2016-04-01

Spatial filtering techniques are important for improving the spatial quality of light beams. Photonic crystals (PhCs) with a selective spatial (angular) transmittance can also provide spatial filtering with the added benefit transversal symmetries, submillimeter dimensions and monolithic integration in other devices, such as micro-lasers or semiconductor lasers. Workable bandgap PhC configurations require a modulated refractive index with period lengths that are approximately less than the wavelength of radiation. This imposes technical limitations, whereby the available direct laser write (DLW) fabrication techniques are limited in resolution and refractive index depth. If, however, a deflection mechanism is chosen instead, a functional filter PhC can be produced that is operational in the visible wavelength regime. For deflection based PhCs glass is an attractive choice as it is highly stable medium. 2D and 3D PhC filter variations have already been produced on soda-lime glass. However, little is known about how to control the scattering of PhCs when approaching the smallest period values. Here we look into the internal structure of the initially symmetric geometry 2D PhCs and associating it with the resulting transmittance spectra. By varying the DLW fabrication beam parameters and scanning algorithms, we show that such PhCs contain layers that are comprised of semi-tilted structure voxels. We show the appearance of asymmetry can be compensated in order to circumvent some negative effects at the cost of potentially maximum scattering efficiency.

Anthrax Vaccine does not affect semen Parameters, Embryo Quality, or Pregnancy Outcome in Couples with a Vaccinated Male Military Service Member

DTIC Science & Technology

2005-02-01

concern that accination of predominantly reproductive-aged service- embers may result in deleterious effects on fertility or etal health (6). There are...requests: William H. Catherino, M.D., Ph.D., Department of Obstetrics and Gynecology, Uniformed Services University of the Health Sciences, Building A...ORGANIZATION NAME(S) AND ADDRESS(ES) Uniformed Services University of the Health Sciences,Department of Obstetrics and Gynecology,4301 Jones Bridge Road

Investigation of the Dissolution Profile of Gliclazide Modified-Release Tablets Using Different Apparatuses and Dissolution Conditions.

PubMed

Skripnik, K K S; Riekes, M K; Pezzini, B R; Cardoso, S G; Stulzer, H K

2017-07-01

In the absence of an official dissolution method for modified-release tablets of gliclazide, dissolution parameters, such as apparatuses (1, 2, and 3), rotation speeds, pH, and composition of the dissolution medium were investigated. The results show that although the drug presents a pH-mediated solubility (pH 7.0 > 6.8 > 6.4 > 6.0 > 5.5 > 4.5), the in vitro release of the studied tablets was not dependent on this parameter, despite of the apparatus tested. On the other hand, the rotation speed demonstrated a greater influence (100 rpm >50 rpm). Using similar hydrodynamic conditions, the three different apparatuses were compared in pH 6.8 and provided the following trend: apparatus 1 at 100 rpm >2 at 50 rpm ≈3 at 10 dpm. As a complete, but slow release is expected from modified-release formulations, apparatus 2, in phosphate buffer pH 6.8 and 100 rpm, were selected as the optimized dissolution method. In comparison to apparatus 1 under the same conditions, the paddle avoids the stickiness of formulation excipients at the mesh of the basket, which could prejudice the release of gliclazide. Results obtained with biorelevant medium through the developed dissolution method were similar to the buffer solution pH 6.8. The application of the optimized method as a quality control test between two different brands of gliclazide modified-release tablets showed that both dissolution profiles were considered similar by the similarity factor (f2 = 51.8). The investigation of these dissolution profiles indicated a dissolution kinetic following first-order model.

Potable water quality monitoring of primary schools in Magura district, Bangladesh: children's health risk assessment.

PubMed

Rahman, Aminur; Hashem, Abul; Nur-A-Tomal, Shahruk

2016-12-01

Safe potable water is essential for good health. Worldwide, school-aged children especially in the developing countries are suffering from various water-borne diseases. In the study, drinking water supplies for primary school children were monitored at Magura district, Bangladesh, to ensure safe potable water. APHA standard analytical methods were applied for determining the physicochemical parameters of the water samples. For determination of the essential physicochemical parameters, the samples were collected from 20 randomly selected tube wells of primary schools at Magura. The metal contents, especially arsenic (As), iron (Fe), and manganese (Mn), in the water samples were analyzed by atomic absorption spectroscopy. The range of physicochemical parameters found in water samples were as follows: pH 7.05-9.03, electrical conductivity 400-2340 μS/cm, chloride 10-640 mg/L, hardness 200-535 mg/L as CaCO 3 , and total dissolved solids 208-1216 mg/L. The level of metals in the tube well water samples were as follows: As 1 to 55 μg/L, Fe 40 to 9890 μg/L, and Mn 10 to 370 μg/L. Drinking water parameters of Magura district did not meet the requirement of the World Health Organization drinking water quality guideline, or the Drinking Water Quality Standards of Bangladesh.

Geospatial modelling for groundwater quality mapping: a case study of Rupnagar district, Punjab, India

NASA Astrophysics Data System (ADS)

Sahoo, S.; Kaur, A.; Litoria, P.; Pateriya, B.

2014-11-01

Over period of time, the water usage and management is under stress for various reasons including pollution in both surface and subsurface. The groundwater quality decreases due to the solid waste from urban and industrial nodes, rapid use of insecticides and pesticides in agricultural practices. In this study, ground water quality maps for Rupnagar district of Punjab has been prepared using geospatial interpolation technique through Inverse Distance Weighted (IDW) approach. IDW technique has been used for major ground water quality parameters observed from the field samples like Arsenic, Hardness, pH, Iron, Fluoride, TDS, and Sulphate. To assess the ground water quality of the Rupnagar district, total 280 numbers of samples from various sources of tubewells for both pre and post monsoon have collected. Out of which, 80 to 113 samples found Iron with non potable limits ranging 0.3-1.1mg/l and 0.3-1.02mg/l according to BIS standard for both the seasons respectively. Chamkaur Sahib, Rupnagar, Morinda blocks have been found non potable limit of iron in both pre & post-monsoon. 11 to 52 samples in this region have sulphate with permissible limits in both the season ranging 200-400mg/l and 201-400mg/l. But arsenic had acceptable limit in both the season. Various parameters-wise ground water quality map is generated using the range values of drinking water quality to know the distribution of different parameters and diversification in the concentration of different elements. These maps are very much needful for human being to expand awareness among the people to maintain the Cleanness of water at their highest quality and purity levels to achieve a healthy life.

Evaluation of groundwater quality in rural-areas of northern Malawi: Case of Zombwe Extension Planning Area in Mzimba

NASA Astrophysics Data System (ADS)

Chidya, Russel C. G.; Matamula, Swithern; Nakoma, Oliver; Chawinga, Charles B. J.

2016-06-01

Many people in in the Sub-Saharan region rely on groundwater for drinking and other household uses. Despite this significance, information on the chemical composition of the water in the boreholes and emperical data on groundwater quality is limited in some rural areas of Malawi. This study was conducted to evaluate the physico-chemical quality of water from boreholes (n = 20) in Zombwe Extension Planning Area (EPA), Mzimba in Northern Malawi to ascertain their safety. Desktop studies and participatory approaches were employed to assess the socio-economic activities and water supply regime in the study areas. The water samples were analysed for pH, conductivity (EC), turbidity, water temperature, nitrate (NO3-), magnesium (Mg), calcium (Ca), zinc (Zn), fluoride (F-), and sulphate (SO42-). In-situ and laboratory analyses were carried out using portable meters and standard procedures. The results were compared with national (Malawi Bureau of Standards - MBS) and international standards (World Health Organization - WHO) for drinking water. The following ranges were obtained: pH (6.00-7.80), EC (437-3128 μS/cm), turbidity (0.10-5.80 NTU), water temperature (27.0-30.60 °C), NO3- (0.30-30.00 mg/L), F- (0.10-8.10 mg/L), Mg (31.00-91.00 mg/L), Ca (20.00-197.10 mg/L), SO42- (10.20-190 mg/L), Fe (0.10-3.60 mg/L) and Zn (0.00-5.10 mg/L). Generally, some parameters tested at several sites (>80%, n = 20) complied with both MBS and WHO limits. No significant differences (p > 0.05) was observed for most parameters (>65%, n = 11). Groundwater contamination was not significant in the area despite some parameters like F-, Ca and SO42- showing higher levels at other sites. Some sites registered very hard water (244.60-757.80 mg/L CaCO3) probably due to mineralization influenced by underground rock material. Further studies are needed to ascertain the groundwater quality of other parameters (like F-, and SO42-) which registered higher levels at some sites. Routine monitoring of the groundwater in the study area and entire Malawi is needed for spatio-temporal variation assessment and to ensure good public health.

Application of a quality by design approach to the cell culture process of monoclonal antibody production, resulting in the establishment of a design space.

PubMed

Nagashima, Hiroaki; Watari, Akiko; Shinoda, Yasuharu; Okamoto, Hiroshi; Takuma, Shinya

2013-12-01

This case study describes the application of Quality by Design elements to the process of culturing Chinese hamster ovary cells in the production of a monoclonal antibody. All steps in the cell culture process and all process parameters in each step were identified by using a cause-and-effect diagram. Prospective risk assessment using failure mode and effects analysis identified the following four potential critical process parameters in the production culture step: initial viable cell density, culture duration, pH, and temperature. These parameters and lot-to-lot variability in raw material were then evaluated by process characterization utilizing a design of experiments approach consisting of a face-centered central composite design integrated with a full factorial design. Process characterization was conducted using a scaled down model that had been qualified by comparison with large-scale production data. Multivariate regression analysis was used to establish statistical prediction models for performance indicators and quality attributes; with these, we constructed contour plots and conducted Monte Carlo simulation to clarify the design space. The statistical analyses, especially for raw materials, identified set point values, which were most robust with respect to the lot-to-lot variability of raw materials while keeping the product quality within the acceptance criteria. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

Evaluation of spatial and temporal water quality in the Akkaya dam watershed (Niğde, Turkey) and management implications

NASA Astrophysics Data System (ADS)

Yaşar Korkanç, Selma; Kayıkçı, Sedef; Korkanç, Mustafa

2017-05-01

The aim of this study is to investigate the water pollution in the Akkaya Dam watershed spatially and temporally and put forward management suggestions in a watershed scale. For this purpose, monthly water sampling was performed from 11 sampling stations on streams that fed the dam. According to land surveys they have a potential to inflict pollution to the dam. Thus the physical and chemical parameters (i.e. pH, dissolved oxygen, electrical conductivity, temperature, chemical oxygen demand, turbidity and suspended solids) were monitored monthly for 1-year period. Chloride, sulfate, total nitrogen, ammonium, nitrite, nitrate were monitored for a 6-month period, and the results were evaluated in accordance with the Turkish Regulation of Surface Water Quality Management. Results of the study show that the most important reasons for the pollution in the dam are caused by domestic and industrial wastewaters, which were released to the system without being treated, or without being sufficiently treated, and also of agricultural activities. It was determined that electrical conductivity, dissolved oxygen, turbidity, chemical oxygen demand, suspended solids, nitrite, nitrate, total nitrogen, sulfate, and chloride parameters which were high at the sampling stations where domestic and industrial wastewaters discharge were present. pH and temperature demonstrate a difference at a significant level by seasons. As a result of the study, it was determined that the water was of IVth quality in terms of nitrate, chemical oxygen demand, and total nitrogen, and it was of IIIrd quality water with respect to ammonium, electrical conductivity, and dissolved oxygen. It was observed that the dam outflow water was of IVth quality with respect to nitrate, chemical oxygen demand, and total nitrogen, and of IIIrd quality with respect to dissolved oxygen and electrical conductivity. It is considered that the pollution problem in the Akkaya Dam can only be resolved with prevention studies on a watershed scale. Therefore, coordination between the institutions is necessary. The preparation for the integrated water management plan of the watershed will provide a significant contribution to the solution of the water quality problem.

An assessment of the water quality of drinking water in rural districts in Zimbabwe. The case of Gokwe South, Nkayi, Lupane, and Mwenezi districts

NASA Astrophysics Data System (ADS)

Hoko, Zvikomborero

Zimbabwe generally receives an average rainfall of 675 mm per annum of which only a maximum of 10% finds its way to rivers as runoff. Gokwe, Nkayi, Lupane and Mwenezi are some of the driest districts in Zimbabwe having mean annual runoffs (MAR) in the range 17-70 mm. River flows especially in Nkayi and Lupane are seasonal and often dry in the period June to November every year. The Kalahari sands predominantly found in such areas as Gokwe, Nkayi, and Lupane promote rapid percolation of rainwater leaving little runoff. The main source of water for domestic purposes in these areas is groundwater with very little reliance on surface water. This study analyzed the water quality of water points in Gokwe South, Nkayi, Lupane, and Mwenezi districts. Parameters analyzed were pH, temperature, dissolved oxygen (DO), turbidity and electrical conductivity (EC). Water quality perceptions from the villagers and the research team were investigated and possible correlations studied. Water quality perceptions included, taste and soap consumption and colour. The uses of the water at domestic level as well as available alternatives to borehole water were investigated. The pH generally ranged from 6.5 to 8.0, which is within the Canadian guidelines. DO was 0.3-5.9 mg/l while turbidity ranged from 0 to 259 NTU with Mwenezi having the highest turbidity value. Conductivity ranged from 70 to 9800 μS/cm with the lowest and highest values recorded in Gokwe and Mwenezi. It was found out that the water quality in terms of taste and odour was 97% satisfactory for Gokwe South, 85% Nkayi, 64% Lupane, and 62% for Mwenezi. High soap consumption which is related to hardness was perceived to be least in Lupane (14%) and highest in Mwenezi with 81%. In general taste complaints also corresponded to high soap consumption but the opposite was not true. It was observed that there was no clear correlation between the quality parameters studied and perceived quality as for example satisfactory taste responses were obtained at EC values higher than the threshold minimum value for objection.

Hydrochemical Characterization of Groundwater Quality for Drinking and Agricultural Purposes: A Case Study in Rafsanjan Plain, Iran.

PubMed

Hosseinifard, Seyed Javad; Mirzaei Aminiyan, Milad

One of the important purposes of hydrology is to ensure water supply in accordance with the quality criteria for agricultural, industrial, and drinking water uses. The groundwater is the main source of water supply in arid and semi-arid regions. This study was conducted to evaluate factors regulating groundwater quality in Rafsanjan plain. A total of 1040 groundwater samples randomly were collected from different areas of Rafsanjan. Then, each sample was analyzed for the major ions based on standard methods. The pH, SAR, EC, and TDS parameters and concentrations of Ca 2+ , Mg 2+ , and Na + cations, and Cl - , [Formula: see text], [Formula: see text] and [Formula: see text] anions were measured. Also boron concentration in each sample was determined. Although, maximum and minimum values of EC and TDS linked to the Anar-Beyaz area and Eastern Urban, respectively, irrigation water EC condition, however, was critical in the study areas. The pH value in Western Urban was higher than the other areas, and its value for Anar-Beyaz area was lower than the other areas, but pH value is at the optimal level in all the study areas. The results showed that hazard state with respect to Mg was critical except in Koshkoueiyeh and Anar-Beyaz areas, that these areas are marginal for irrigation use with little harm with reference to Mg. From the results, it was concluded that the status of boron concentration in study areas was critical. According to the hydrochemistry diagrams, the main groundwater type in different study areas was NaCl. Groundwater quality was not appropriate for drinking usage, and its status for agricultural practices was unsuitable in these areas.

Water Quality Assessment and Determining the Carrying Capacity of Pollution Load Batang Kuranji River

NASA Astrophysics Data System (ADS)

Dewata, I.; Adri, Z.

2018-04-01

This study aims to determine the water quality and carrying capacity of pollution load Batang Kuranji River in the headwaters, middle, and downstream. This research is descriptive quantitative parameters of pH, BOD, COD, TSS, and DOES Depictions of river water quality refer to RegulationNo.82/2001, while determination of carrying capacity of pollution load river refers to the Kep Men LHNo.10/2003.The result is Kuranji Batang River water quality upstream region included in either category who meet the quality standard first class ofPP82/2001. TSS concentrations at head waters of 21 mg/L, BOD1,6 mg/L, COD7,99mg/L and DO 7,845 mg/L. While the carrying capacity of pollution load river in upstream region included in both categories namely BOD of 4,4 kg/sec, COD 273,60 kg/sec, TSS906,00kg/sec, and DO parameters of 49.20 kg/sec. Middle region (point 2, 3, and 4) water quality Batang Kuranji River has exceeded the quality standard of 82/2001 for class II and class III. Meanwhile, carrying capacity of pollution load river in area included in ugly category. The calculation is done with application Qual2Kw show that carrying capacity of pollution load river of BOD -857.3 kg/sec, COD -777.40 kg/sec, TSS +9511.5 kg/sec, and DO +69.30 kg/sec.

The effect of fermented apple diet supplementation on the growth performance and meat quality in finishing pigs.

PubMed

Lee, Sung Dae; Kim, Hoi Yun; Jung, Hyun Jung; Ji, Sang Yun; Chowdappa, Rekha; Ha, Ji Hee; Song, Young Min; Park, Jun Cheol; Moon, Hong Kil; Kim, In Cheul

2009-02-01

The objective of the present study was to investigate the effect of fermented apple diet (FAD) supplementation on the growth performance and meat quality in finishing Berkshires. The FAD was made from dropped apple mixed with rice bran and barley bran. Until 81 +/- 1 kg live weight at 133 +/- 1 days, the animals were fed a growing diet, after which experimental samples were fixed at 0, 2, 4 and 6% FAD as C, T1, T2 and T3 in the finishing diets. Growth performance, ADG, ADFI and feed efficiency were improved in T1 than other groups. In carcass parameters, carcass weight was higher (P < 0.05) in T1 than in other groups. In meat quality, moisture and crude protein contents decreased (P < 0.05) by addition of FAD. pH(24) and WHC were higher (P < 0.05) in T1 than other groups. In sensory evaluation, marbling of fresh meat and tenderness, juiciness, flavor and overall acceptability of cooked meat were improved by the addition of FAD. According to the results of our experiment, FAD can be used for improvement of meat quality parameters.

Variation in the composition of corals, fishes, sponges, echinoderms, ascidians, molluscs, foraminifera and macroalgae across a pronounced in-to-offshore environmental gradient in the Jakarta Bay-Thousand Islands coral reef complex.

PubMed

Cleary, D F R; Polónia, A R M; Renema, W; Hoeksema, B W; Rachello-Dolmen, P G; Moolenbeek, R G; Budiyanto, A; Yahmantoro; Tuti, Y; Giyanto; Draisma, S G A; Prud'homme van Reine, W F; Hariyanto, R; Gittenberger, A; Rikoh, M S; de Voogd, N J

2016-09-30

Substrate cover, water quality parameters and assemblages of corals, fishes, sponges, echinoderms, ascidians, molluscs, benthic foraminifera and macroalgae were sampled across a pronounced environmental gradient in the Jakarta Bay-Thousand Islands reef complex. Inshore sites mainly consisted of sand, rubble and turf algae with elevated temperature, dissolved oxygen, pH and chlorophyll concentrations and depauperate assemblages of all taxa. Live coral cover was very low inshore and mainly consisted of sparse massive coral heads and a few encrusting species. Faunal assemblages were more speciose and compositionally distinct mid- and offshore compared to inshore. There were, however, small-scale differences among taxa. Certain midshore sites, for example, housed assemblages resembling those typical of the inshore environment but this differed depending on the taxon. Substrate, water quality and spatial variables together explained from 31% (molluscs) to 72% (foraminifera) of the variation in composition. In general, satellite-derived parameters outperformed locally measured parameters. Copyright © 2016 Elsevier Ltd. All rights reserved.

Physicochemical parameters affecting the perception of borehole water quality in Ghana.

PubMed

Kulinkina, Alexandra V; Plummer, Jeanine D; Chui, Kenneth K H; Kosinski, Karen C; Adomako-Adjei, Theodora; Egorov, Andrey I; Naumova, Elena N

2017-08-01

Rural Ghanaian communities continue using microbiologically contaminated surface water sources due in part to undesirable organoleptic characteristics of groundwater from boreholes. Our objective was to identify thresholds of physical and chemical parameters associated with consumer complaints related to groundwater. Water samples from 94 boreholes in the dry season and 68 boreholes in the rainy season were analyzed for 18 parameters. Interviews of consumers were conducted at each borehole regarding five commonly expressed water quality problems (salty taste, presence of particles, unfavorable scent, oily sheen formation on the water surface, and staining of starchy foods during cooking). Threshold levels of water quality parameters predictive of complaints were determined using the Youden index maximizing the sum of sensitivity and specificity. The probability of complaints at various parameter concentrations was estimated using logistic regression. Exceedances of WHO guidelines were detected for pH, turbidity, chloride, iron, and manganese. Concentrations of total dissolved solids (TDS) above 172mg/L were associated with salty taste complaints. Although the WHO guideline is 1000mg/L, even at half the guideline, the likelihood of salty taste complaint was 75%. Iron concentrations above 0.11, 0.14 and 0.43mg/L (WHO guideline value 0.3mg/L) were associated with complaints of unfavorable scent, oily sheen, and food staining, respectively. Iron and TDS concentrations exhibited strong spatial clustering associated with specific geological formations. Improved groundwater sources in rural African communities that technically meet WHO water quality guidelines may be underutilized in preference of unimproved sources for drinking and domestic uses, compromising human health and sustainability of improved water infrastructure. Copyright © 2017 Elsevier GmbH. All rights reserved.

Honey physicochemical properties of three species of the Brazilian Melipona.

PubMed

Lage, Lorena G A; Coelho, Lívia L; Resende, Helder C; Tavares, Mara G; Campos, Lucio A O; Fernandes-Salomão, Tânia M

2012-09-01

Physicochemical analyses were carried out to evaluate 27 samples of honeys from three species of the Brazilian genus Melipona (M. capixaba, M. rufiventris and M. mondury) from Espírito Santo and Minas Gerais States. The parameters water activity (Aw), percentage of soluble solids (Brix %), pH, acidity (meq/Kg) and moisture (%) were evaluated. The honey characteristics obtained from these samples were very similar to the ones from other Melipona species. However, regarding the honey from Apis (honey bee), only the pH values were similar. The low pH value and the high acidity detected in Melipona honey are potential factors for increasing the honey shelf life because they do not provide favorable conditions for the microbial development. On the other hand, the high level of water activity favors the growth of microorganisms, especially yeast, which demands a more careful handled and storage. The observed differences between Melipona and Apis honey reinforce the need for specific quality settings for stingless bee honey.

40 CFR 436.42 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Industrial Sand Subcategory § 436.42 Effluent limitations guidelines representing the degree of effluent... 6.0 and water quality criteria in water quality standards approved under the Act authorize such lower pH, the pH limitation for such discharge may be adjusted downward to the pH water quality...

Meat quality attributes of the Longissimus lumborum muscle of the Kh'ara genotype of llama (Lama glama) reared extensively in northern Chile.

PubMed

Mamani-Linares, L W; Gallo, C B

2013-05-01

Twenty male llama of the Kh'ara genotype, reared extensively in the north of Chile, were slaughtered at ages between 2 and 4 permanent teeth (2 to 3.5years) and analyses were carried out on the Longissimus lumborum muscle, including composition (moisture, fat, protein, ash, cholesterol, amino acids, fatty acid profile and collagen content) and meat quality parameters (pH, color, water holding capacity and Warner-Bratzler shear-force). Llama meat was characterized by a low cholesterol (39.04mg/100g) and intramuscular fat (1.56%) content, a total collagen content of 6.28mg/g, of which 20.28% was soluble collagen. Amino acid composition and fatty acid profile were similar to those found for beef finished on forage. Llama meat showed a low n-6/n-3 (4.69) and hypocholesterolemic/hypercholesterolemic (1.55) ratio and acceptable values of DFA (65.78%). Quality parameters in llama Longissimus muscle were within the ranges reported for more traditional meats such as beef and lamb. Copyright © 2012 Elsevier Ltd. All rights reserved.

Sustainable solar energy capability studies by using S2H model in treating groundwater supply

NASA Astrophysics Data System (ADS)

Musa, S.; Anuar, M. F.; Shahabuddin, M. M.; Ridzuan, M. B.; Radin Mohamed, R. M. S.; Madun, M. A.

2018-04-01

Groundwater extracted in Research Centre for Soft Soil Malaysia (RECESS) contains a number of pollutants that exceed the safe level for consumption. A Solar-Hydro (S2H) model which is a practical prototype has been introduced to treat the groundwater sustainably by solar energy process (evaporation method). Selected parameters was tested which are sulphate, nitrate, chloride, fluoride, pH and dissolved oxygen. The water quality result shows that all parameters have achieved 100% of the drinking water quality standard issued by the Ministry of Health Malaysia. Evaporation method was proven that this solar energy can be applied in sustainably treating groundwater quality with up to 90% effectiveness. On the other hand, the quantitative analysis has shown that the production of clean water is below than 2% according to time constraints and design factors. Thus, this study can be generate clean and fresh water from groundwater by using a simplified model and it has huge potential to be implemented by the local communities with a larger scale and affordable design.

River pollution caused by natural stone industry

NASA Astrophysics Data System (ADS)

Oktriani, Ani; Darmajanti, Linda; Soesilo, Tri Edhi Budhi

2017-03-01

The natural stone industry is classified as small industry. Current wastewater treatment still causes pollution in the river. This thesis aims to analyze the performance of wastewater treatment in natural stones industry. The data was collected from water quality test (parameters: temperature, pH, DO, and TSS). The wastewater treatment performance was in a slightly higher position compared to the 2nd class quality standards of Government Regulation No. 82/2001. The parameter that exceeded quality standards was the concentration of TSS, which was up to 240.8 mg/l. The high concentration of TSS was affected by the absence of sludge management schedule, which resulted in non-optimal precipitation. Besides that, the design of sedimentation basin was still not adapted with wastewater debit. Referring to the results, this study suggests the government of Cirebon District to provide wastewater treatment development through the village staff. Furthermore, the government also needs to give strict punishment to business owner who does not treat waste correctly and does not have a business license. Moreover, the sale value of sludge as byproduct of wastewater treatment needs to be increased.

Groundwater quality and hydrogeochemical properties of Torbali Region, Izmir, Turkey.

PubMed

Tayfur, Gokmen; Kirer, Tugba; Baba, Alper

2008-11-01

The large demand for drinking, irrigation and industrial water in the region of Torbali (Izmir, Turkey) is supplied from groundwater sources. Almost every factory and farm has private wells that are drilled without permission. These cause the depletion of groundwater and limiting the usage of groundwater. This study investigates spatial and temporal change in groundwater quality, relationships between quality parameters, and sources of contamination in Torbali region. For this purpose, samples were collected from 10 different sampling points chosen according to their geological and hydrogeological properties and location relative to factories, between October 2001 and July 2002. Various physical (pH, temperature, EC), chemical (calcium, magnesium, potassium, sodium, chloride, alkalinity, copper, chromium, cadmium, lead, zinc) and organic (nitrate, nitrite, ammonia, COD and cyanide) parameters were monitored. It was observed that the groundwater has bicarbonate alkalinity. Agricultural contamination was determined in the region, especially during the summer. Nitrite and ammonia concentrations were found to be above drinking water standard. Organic matter contamination was also investigated in the study area. COD concentrations were higher than the permissible limits during the summer months of the monitoring period.

Comparative analysis of the outflow water quality of two sustainable linear drainage systems.

PubMed

Andrés-Valeri, V C; Castro-Fresno, D; Sañudo-Fontaneda, L A; Rodriguez-Hernandez, J

2014-01-01

Three different drainage systems were built in a roadside car park located on the outskirts of Oviedo (Spain): two sustainable urban drainage systems (SUDS), a swale and a filter drain; and one conventional drainage system, a concrete ditch, which is representative of the most frequently used roadside drainage system in Spain. The concentrations of pollutants were analyzed in the outflow of all three systems in order to compare their capacity to improve water quality. Physicochemical water quality parameters such as dissolved oxygen, total suspended solids, pH, electrical conductivity, turbidity and total petroleum hydrocarbons were monitored and analyzed for 25 months. Results are presented in detail showing significantly smaller amounts of outflow pollutants in SUDS than in conventional drainage systems, especially in the filter drain which provided the best performance.

A Total Quality Leadership Process Improvement Model

DTIC Science & Technology

1993-12-01

Leadership Process Improvement Model by Archester Houston, Ph.D. and Steven L. Dockstader, Ph.D. DTICS ELECTE tleaese oand sale itsFeat ben proe 94-12058...tTl ’AND SIATE COVERID0 Z lits Z40 uerI’Ll12/93 IFinalS.FNR IM F A Total Quality Leadership Process Improvement Model M ARRhOW~ Archester Houston, Ph.D...and Steven L. Dockstader, Ph.D. ?. 7PEJORMING ORG-AN1:AION NAMEIS) AND 00-RESS(ES) L PERFORMIN4 ORAINIZATION Total Quality Leadership OfficeREOTNMR

Dietary green tea polyphenols do not affect vitamin E status, antioxidant capacity and meat quality of growing pigs.

PubMed

Augustin, K; Blank, R; Boesch-Saadatmandi, C; Frank, J; Wolffram, S; Rimbach, G

2008-12-01

Supplementation of pigs with vitamin E, the most important lipid-soluble antioxidant, has been shown to improve meat quality and animal health. Previous studies in cultured cells and laboratory animals indicate synergistic effects between polyphenols and vitamin E. The present feeding trial was undertaken to investigate the effects of dietary green tea polyphenols (GTP) on vitamin E status, antioxidative capacity and parameters of meat quality in growing pigs. Eighteen castrated, crossbred, male pigs received a flavonoid-poor diet based on corn starch, caseinate and rapeseed oil with a total vitamin E content of 17 IU/kg diet over a period of 5 weeks. This basal diet was supplemented with green tea extract to provide daily doses of 0 (control), 10 and 100 mg GTP/kg body weight. Dietary supplementation of growing pigs with GTP did not affect serum, liver, lung and muscle vitamin E (alpha- and gamma-tocopherol) concentrations, plasma antioxidant capacity (ferric reducing ability of plasma, trolox equivalent antioxidant capacity) or parameters of meat quality including meat temperature, pH, conductivity, colour and drip loss. In conclusion, supplementation of pig diets with green tea catechins is not associated with improved antioxidant status and meat quality under practice-oriented conditions.

Analysis of interrelation between water quality and hydrologic conditions on a small karst catchment area of sinking watercourse Trbuhovica

NASA Astrophysics Data System (ADS)

Hinić, V.; Rubinić, J.; Vučković, I.; Ružić, I.; Gržetić, A.; Volf, G.; Ljubotina, M.; Kvas, N.

2008-11-01

Sinking watercourse Trbuhovica is located at the topping karst of Gorski Kotar in Croatia, near the Slovenian border. About 900 inhabitants live in Trbuhovica catchment area. Sewage system had not been built. The project KEEP WATERS CLEAN (INTERREG III A project) was approved by EU commission and has a purpose of investigating water resources of that area, their appropriate protection and improving management of those resources. This paper presents project's 1st phase investigation results: hydrologic conditions and water quality at several locations on stream and at the springs of Trbuhovica, Mlake and Obrh. Climatologic (precipitation, air temperature and snow cover), basic hydrologic characteristics (flow and water temperature), water quality parameters (pH, electric conductivity, alkalinity, oxygen regime, nutrients and mineral oils) and microbiology indicators have been monitored. Samples of micro invertebrates and samples of periphyton have been collected in the field. Biological results have been elaborated via Saprobial Index according to Pantle-Buck. Analyses results showed a strong connection between hydrologic condition and selected water quality parameters. The groundwater quality changes are very quick. Maximum pollutions occur during the period of intensive rain. Water at the spring of Mlaka is very clean and is classified in the first to second water category, while Trbuhovica shows higher organic pollution.

The interactive effects of transportation and lairage time on welfare indicators, carcass and meat quality traits in slaughter pigs

NASA Astrophysics Data System (ADS)

Čobanović, N.; Vasilev, D.; Dimitrijević, M.; Teodorović, V.; Parunović, N.; Betić, N.; Karabasil, N.

2017-09-01

This study assessed the effects of transportation and lairage time and their interaction on welfare, carcass and meat quality traits in slaughter pigs under commercial conditions. The study was conducted on 120 pigs with a live weight of approximately 115 kg and about six months old. A complete blood picture was measured in pigs to assess pre-slaughter stress. Also, nine different carcass quality parameters including live weight, hot and cold carcass weights, cooling loss, dressing percentage, backfat thickness, meatiness and skin lesions score were measured. The pH and temperature measurements were performed 45 minutes post-mortem. The results showed that short transportation time and slaughtering without lairaging and long transportation time and overnight lairaging negatively influenced the hematological parameters, which meant that the animal welfare was seriously compromised under these pre-slaughter conditions. Long transportation time and overnight lairaging reduced live and carcass weights and increased the incidence of skin lesions on the carcass and DFD pork. In addition, short transportation time and slaughtering without lairaging caused a significant deterioration in pork quality. It can be concluded that, from the standpoint of animal welfare, carcass and meat quality, the above-mentioned pre-slaughter conditions are not recommended to the farmers and/or pork producers.

Inductive-capacitive resonant circuit sensors for structural health and environmental monitoring

NASA Astrophysics Data System (ADS)

DeRouin, Andrew J.

Inductive-capacitive (LC) sensors are low-cost, wireless, durable, simple to fabricate and battery-less. Consequently, they are well suited to sensing applications in harsh environments or where large numbers of sensors are needed. Due to their many advantages, LC sensors have been used for sensing a variety of parameters including humidity, temperature, chemical concentrations, pH, stress/pressure, strain, food quality and even biological growth. However, current versions of the LC sensor technology are limited to sensing only one parameter. This work focuses on the development and characterization of two new sensor designs that address this limitation in addition to significantly reducing the overall sensor footprint and thus the sensor unit cost.

Impact of urbanization on the ecology of Mukuvisi River, Harare, Zimbabwe

NASA Astrophysics Data System (ADS)

Moyo, N. A. G.; Rapatsa, M. M.

2016-04-01

The main objective in this study was to compare the physico-chemical characteristics and biota of a river (Mukuvisi) passing through an urban area to that of a non-urbanised river (Gwebi). Five sites in the Mukuvisi River and five sites in the Gwebi River were sampled for water physico-chemical parameters (pH, conductivity, DO, BOD, TDS, ammonia, Cl, SO42-, PO42-, NO33-, F-, Pb, Cu, Fe, Mn, Zn and Cr) once every month between August, 2012-August, 2013. Cluster analysis based on the physico-chemical parameters grouped the sites into two groups. Mukuvisi River sites formed their own grouping except for one site which was grouped with Gwebi River sites. Principal Component Analysis (PCA) was used to extract the physico-chemical parameters that account for most variations in water quality in the Mukuvisi and Gwebi Rivers. PCA identified sulphate, chloride, fluoride, iron, manganese and zinc as the major factors contributing to the variability of Mukuvisi River water quality. In the Gwebi river, sulphate, nitrate, fluoride and copper accounted for most of the variation in water quality. Canonical Correspondence Analysis (CCA) was used to explore the relationship between physico-chemical parameters and macroinvertebrate communities. CCA plots in both Mukuvisi and Gwebi Rivers showed significant relationships between macroinvertebrate communities and water quality variables. Phosphate, ammonia and nitrates were correlated with Chironomidae and Simulidae. Gwebi River had higher (P < 0.05, ANOVA) macroinvertebrates and fish diversity than Mukuvisi River. Clarias gariepinus from the Mukuvisi River had high liver histological lesions and low AChE activity and this led to lower growth rates in this river.

In situ sensor technology for simultaneous spectrophotometric measurements of seawater total dissolved inorganic carbon and pH.

PubMed

Wang, Zhaohui Aleck; Sonnichsen, Frederick N; Bradley, Albert M; Hoering, Katherine A; Lanagan, Thomas M; Chu, Sophie N; Hammar, Terence R; Camilli, Richard

2015-04-07

A new, in situ sensing system, Channelized Optical System (CHANOS), was recently developed to make high-resolution, simultaneous measurements of total dissolved inorganic carbon (DIC) and pH in seawater. Measurements made by this single, compact sensor can fully characterize the marine carbonate system. The system has a modular design to accommodate two independent, but similar measurement channels for DIC and pH. Both are based on spectrophotometric detection of hydrogen ion concentrations. The pH channel uses a flow-through, sample-indicator mixing design to achieve near instantaneous measurements. The DIC channel adapts a recently developed spectrophotometric method to achieve flow-through CO2 equilibration between an acidified sample and an indicator solution with a response time of only ∼ 90 s. During laboratory and in situ testing, CHANOS achieved a precision of ±0.0010 and ± 2.5 μmol kg(-1) for pH and DIC, respectively. In situ comparison tests indicated that the accuracies of the pH and DIC channels over a three-week time-series deployment were ± 0.0024 and ± 4.1 μmol kg(-1), respectively. This study demonstrates that CHANOS can make in situ, climatology-quality measurements by measuring two desirable CO2 parameters, and is capable of resolving the CO2 system in dynamic marine environments.

Short-Term Exposure of Mytilus coruscus to Decreased pH and Salinity Change Impacts Immune Parameters of Their Haemocytes.

PubMed

Wu, Fangli; Xie, Zhe; Lan, Yawen; Dupont, Sam; Sun, Meng; Cui, Shuaikang; Huang, Xizhi; Huang, Wei; Liu, Liping; Hu, Menghong; Lu, Weiqun; Wang, Youji

2018-01-01

With the release of large amounts of CO 2 , ocean acidification is intensifying and affecting aquatic organisms. In addition, salinity also plays an important role for marine organisms and fluctuates greatly in estuarine and coastal ecosystem, where ocean acidification frequently occurs. In present study, flow cytometry was used to investigate immune parameters of haemocytes in the thick shell mussel Mytilus coruscus exposed to different salinities (15, 25, and 35‰) and two pH levels (7.3 and 8.1). A 7-day in vivo and a 5-h in vitro experiments were performed. In both experiments, low pH had significant effects on all tested immune parameters. When exposed to decreased pH, total haemocyte count (THC), phagocytosis (Pha), esterase (Est), and lysosomal content (Lyso) were significantly decreased, whereas haemocyte mortality (HM) and reactive oxygen species (ROS) were increased. High salinity had no significant effects on the immune parameters of haemocytes as compared with low salinity. However, an interaction between pH and salinity was observed in both experiments for most tested haemocyte parameters. This study showed that high salinity, low salinity and low pH have negative and interactive effects on haemocytes of mussels. As a consequence, it can be expected that the combined effect of low pH and changed salinity will have more severe effects on mussel health than predicted by single exposure.

Prediction of ground water quality index to assess suitability for drinking purposes using fuzzy rule-based approach

NASA Astrophysics Data System (ADS)

Gorai, A. K.; Hasni, S. A.; Iqbal, Jawed

2016-11-01

Groundwater is the most important natural resource for drinking water to many people around the world, especially in rural areas where the supply of treated water is not available. Drinking water resources cannot be optimally used and sustained unless the quality of water is properly assessed. To this end, an attempt has been made to develop a suitable methodology for the assessment of drinking water quality on the basis of 11 physico-chemical parameters. The present study aims to select the fuzzy aggregation approach for estimation of the water quality index of a sample to check the suitability for drinking purposes. Based on expert's opinion and author's judgement, 11 water quality (pollutant) variables (Alkalinity, Dissolved Solids (DS), Hardness, pH, Ca, Mg, Fe, Fluoride, As, Sulphate, Nitrates) are selected for the quality assessment. The output results of proposed methodology are compared with the output obtained from widely used deterministic method (weighted arithmetic mean aggregation) for the suitability of the developed methodology.

Spatial and temporal characterizations of water quality in Kuwait Bay.

PubMed

Al-Mutairi, N; Abahussain, A; El-Battay, A

2014-06-15

The spatial and temporal patterns of water quality in Kuwait Bay have been investigated using data from six stations between 2009 and 2011. The results showed that most of water quality parameters such as phosphorus (PO4), nitrate (NO3), dissolved oxygen (DO), and Total Suspended Solids (TSS) fluctuated over time and space. Based on Water Quality Index (WQI) data, six stations were significantly clustered into two main classes using cluster analysis, one group located in western side of the Bay, and other in eastern side. Three principal components are responsible for water quality variations in the Bay. The first component included DO and pH. The second included PO4, TSS and NO3, and the last component contained seawater temperature and turbidity. The spatial and temporal patterns of water quality in Kuwait Bay are mainly controlled by seasonal variations and discharges from point sources of pollution along Kuwait Bay's coast as well as from Shatt Al-Arab River. Copyright © 2014 Elsevier Ltd. All rights reserved.

Environmentally Responsible Use of Nanomaterials for the Photocatalytic Reduction of Nitrate in Water

NASA Astrophysics Data System (ADS)

Doudrick, Kyle

Nitrate is the most prevalent water pollutant limiting the use of groundwater as a potable water source. The overarching goal of this dissertation was to leverage advances in nanotechnology to improve nitrate photocatalysis and transition treatment to the full-scale. The research objectives were to (1) examine commercial and synthesized photocatalysts, (2) determine the effect of water quality parameters (e.g., pH), (3) conduct responsible engineering by ensuring detection methods were in place for novel materials, and (4) develop a conceptual framework for designing nitrate-specific photocatalysts. The key issues for implementing photocatalysis for nitrate drinking water treatment were efficient nitrate removal at neutral pH and by-product selectivity toward nitrogen gases, rather than by-products that pose a human health concern (e.g., nitrite). Photocatalytic nitrate reduction was found to follow a series of proton-coupled electron transfers. The nitrate reduction rate was limited by the electron-hole recombination rate, and the addition of an electron donor (e.g., formate) was necessary to reduce the recombination rate and achieve efficient nitrate removal. Nano-sized photocatalysts with high surface areas mitigated the negative effects of competing aqueous anions. The key water quality parameter impacting by-product selectivity was pH. For pH < 4, the by-product selectivity was mostly N-gas with some NH4 +, but this shifted to NO2- above pH = 4, which suggests the need for proton localization to move beyond NO2 -. Co-catalysts that form a Schottky barrier, allowing for localization of electrons, were best for nitrate reduction. Silver was optimal in heterogeneous systems because of its ability to improve nitrate reduction activity and N-gas by-product selectivity, and graphene was optimal in two-electrode systems because of its ability to shuttle electrons to the working electrode. "Environmentally responsible use of nanomaterials" is to ensure that detection methods are in place for the nanomaterials tested. While methods exist for the metals and metal oxides examined, there are currently none for carbon nanotubes (CNTs) and graphene. Acknowledging that risk assessment encompasses dose-response and exposure, new analytical methods were developed for extracting and detecting CNTs and graphene in complex organic environmental (e.g., urban air) and biological matrices (e.g. rat lungs).

Effect of pH and pulsed electric field process parameters on the aflatoxin reduction in model system using response surface methodology: Effect of pH and PEF on Aflatoxin Reduction.

PubMed

Vijayalakshmi, Subramanian; Nadanasabhapathi, Shanmugam; Kumar, Ranganathan; Sunny Kumar, S

2018-03-01

The presence of aflatoxin, a carcinogenic and toxigenic secondary metabolite produced by Aspergillus species, in food matrix has been a major worldwide problem for years now. Food processing methods such as roasting, extrusion, etc. have been employed for effective destruction of aflatoxins, which are known for their thermo-stable nature. The high temperature treatment, adversely affects the nutritive and other quality attributes of the food, leading to the necessity of application of non-thermal processing techniques such as ultrasonication, gamma irradiation, high pressure processing, pulsed electric field (PEF), etc. The present study was focused on analysing the efficacy of the PEF process in the reduction of the toxin content, which was subsequently quantified using HPLC. The process parameters of different pH model system (potato dextrose agar) artificially spiked with aflatoxin mix standard was optimized using the response surface methodology. The optimization of PEF process effects on the responses aflatoxin B1 and total aflatoxin reduction (%) by pH (4-10), pulse width (10-26 µs) and output voltage (20-65%), fitted 2FI model and quadratic model respectively. The response surface plots obtained for the processes were of saddle point type, with the absence of minimum or maximum response at the centre point. The implemented numerical optimization showed that the predicted and actual values were similar, proving the adequacy of the fitted models and also proved the possible application of PEF in toxin reduction.

Combined effects of ZnO NPs and seawater acidification on the haemocyte parameters of thick shell mussel Mytilus coruscus.

PubMed

Wu, Fangli; Cui, Shuaikang; Sun, Meng; Xie, Zhe; Huang, Wei; Huang, Xizhi; Liu, Liping; Hu, Menghong; Lu, Weiqun; Wang, Youji

2018-05-15

Flow cytometry was used to investigate the immune parameters of haemocytes in thick-shell mussel Mytilus coruscus exposed to different concentrations of ZnO nanoparticles (NPs) (0, 2.5, and 10mgl -1 ) at two pH levels (7.3 and 8.1) for 14days following a recovery period of 7days. ZnO NPs significantly affected all of the immune parameters throughout the experiment. At high ZnO NPs concentrations, total haemocyte counting, phagocytosis, esterase, and lysosomal content were significantly decreased whereas haemocyte mortality and reactive oxygen species (ROS) were increased. Although low pH also significantly influenced all of the immune parameters of the mussels, its effect was not as strong as that of ZnO NPs. Interactive effects were observed between pH and ZnO NPs in most haemocyte parameters during the exposure period. Although a slight recovery from the stress of ZnO NPs and pH was observed for all immune parameters, significant carry-over effects of low pH and ZnO NPs were still detected. This study revealed that high concentration of ZnO NPs and low pH exert negative and synergistic effects on mussels, and these effects remain even after the mussels are no longer exposed to such stressors. Copyright © 2017 Elsevier B.V. All rights reserved.

The utilization of coconut waste fermentated by aspergillus niger and saccharomyces cerevisiae on meat quality of weaning males rex rabbit

NASA Astrophysics Data System (ADS)

Wahyuni, T. H.; Ginting, N.; Yunilas; Hasnudi; Mirwandono, E.; Siregar, G. A.; Sinaga, I. G.; Sembiring, I.

2018-02-01

Coconut waste (CW) could be applied for animal feed while its nutrition quality were low. This study aims to investigate fermented CW effect on meat quality of Rex rabbit which feed by fermented CW either by Aspergillus niger or Tape Yeast. This research was conducted in rabbit farm Brastagi, using 24 male Rex rabbits with initial weight 1012 ± 126.67 gram in July-October 2016. The design used was complete randomized design : 6 treatment 4 replications. Treatment were T1 (unfermented 10%); T2 (unfermented 20%); T3 (a.niger fermentation 10%); T4 (a niger fermentation 20%); T5 (tape yeast fermentation 10%) and T6 (tape yeast fermentation 20%). The parameters were pH, meat texture either raw or cooked, water content, fat content, protein content of meat and cooking loss. The results showed that effect of treatment was not significantly different (P>0.05) on pH and raw meat texture, but significantly different (P< 0.05) on texture of meat cooked and meat fat content and very significantly different effect ( P> 0,01) on cooking loss, water content and protein content of meat. The conclusion of this research was the utilization of fermented CW by Aspergillius niger and Tape Yeast improved the quality of Rex rabbit meat

Geostatistical Characteristic of Space -Time Variation in Underground Water Selected Quality Parameters in Klodzko Water Intake Area (SW Part of Poland)

NASA Astrophysics Data System (ADS)

Namysłowska-Wilczyńska, Barbara

2016-04-01

This paper presents selected results of research connected with the development of a (3D) geostatistical hydrogeochemical model of the Klodzko Drainage Basin, dedicated to the spatial and time variation in the selected quality parameters of underground water in the Klodzko water intake area (SW part of Poland). The research covers the period 2011÷2012. Spatial analyses of the variation in various quality parameters, i.e, contents of: ammonium ion [gNH4+/m3], NO3- (nitrate ion) [gNO3/m3], PO4-3 (phosphate ion) [gPO4-3/m3], total organic carbon C (TOC) [gC/m3], pH redox potential and temperature C [degrees], were carried out on the basis of the chemical determinations of the quality parameters of underground water samples taken from the wells in the water intake area. Spatial and time variation in the quality parameters was analyzed on the basis of archival data (period 1977÷1999) for 22 (pump and siphon) wells with a depth ranging from 9.5 to 38.0 m b.g.l., later data obtained (November 2011) from tests of water taken from 14 existing wells. The wells were built in the years 1954÷1998. The water abstraction depth (difference between the terrain elevation and the dynamic water table level) is ranged from 276÷286 m a.s.l., with an average of 282.05 m a.s.l. Dynamic water table level is contained between 6.22 m÷16.44 m b.g.l., with a mean value of 9.64 m b.g.l. The latest data (January 2012) acquired from 3 new piezometers, with a depth of 9÷10m, which were made in other locations in the relevant area. Thematic databases, containing original data on coordinates X, Y (latitude, longitude) and Z (terrain elevation and time - years) and on regionalized variables, i.e. the underground water quality parameters in the Klodzko water intake area determined for different analytical configurations (22 wells, 14 wells, 14 wells + 3 piezometers), were created. Both archival data (acquired in the years 1977÷1999) and the latest data (collected in 2011÷2012) were analyzed. These data were subjected to spatial analyses using statistical and geostatistical methods. The evaluation of basic statistics of the investigated quality parameters, including their histograms of distributions, scatter diagrams between these parameters and also correlation coefficients r were presented in this article. The directional semivariogram function and the ordinary (block) kriging procedure were used to build the 3D geostatistical model. The geostatistical parameters of the theoretical models of directional semivariograms of the studied water quality parameters, calculated along the time interval and along the wells depth (taking into account the terrain elevation), were used in the ordinary (block) kriging estimation. The obtained results of estimation, i.e. block diagrams allowed to determine the levels of increased values Z* of studied underground water quality parameters. Analysis of the variability in the selected quality parameters of underground water for an analyzed area in Klodzko water intake was enriched by referring to the results of geostatistical studies carried out for underground water quality parameters and also for a treated water and in Klodzko water supply system (iron Fe, manganese Mn, ammonium ion NH4+ contents), discussed in earlier works. Spatial and time variation in the latter-mentioned parameters was analysed on the basis of the data (2007÷2011, 2008÷2011). Generally, the behaviour of the underground water quality parameters has been found to vary in space and time. Thanks to the spatial analyses of the variation in the quality parameters in the Kłodzko underground water intake area some regularities (trends) in the variation in water quality have been identified.

Applications of Geographic Information System (GIS) analysis of Lake Uluabat.

PubMed

Hacısalihoğlu, Saadet; Karaer, Feza; Katip, Aslıhan

2016-06-01

Lake Uluabat is one of the most important wetlands in Turkey because of its rich biodiversity, lying on a migratory bird route with almost all its shores being covered by submerged plants. The lake has been protected by the Ramsar Convention since 1998. However, the Lake is threatened by natural and anthropogenic stressors as a consequence of its location. Geographic Information System (GIS) analysis is a tool that has been widely used, especially for water quality management in recent years. This study aimed to investigate the water quality and determined most polluted points using GIS analysis of the lake. Temperature, pH, dissolved oxygen, chemical oxygen demand, Kjeldahl nitrogen, total phosphorus, chlorophyll-a, arsenic, boron, iron, and manganese were monitored monthly from June 2008 to May 2009, with the samples taken from 8 points in the lake. Effect of pH, relation of temperature, and Chl-a with other water quality parameters and metals are designated as statistically significant. Data were mapped using ArcGIS 9.1 software and were assessed according to the Turkish Water Pollution Control Regulations (TWPCR). The research also focused on classifying and mapping the water quality in the lake by using the spatial analysis functions of GIS. As a result, it was determined that Lake Uluabat belonged to the 4th class, i.e., highly polluted water, including any water of lower quality. A remarkable portion of the pollution in the water basin was attributed to domestic wastewater discharges, industrial and agricultural activities, and mining.

Carcass quality, physico-chemical parameters, muscle fibre traits and myosin heavy chain composition of m. longissimus lumborum from Puławska and Polish Large White pigs.

PubMed

Wojtysiak, Dorota; Połtowicz, Katarzyna

2014-08-01

In 54 Puławska pigs and 60 Polish Large White pigs (PLW), slaughtered at 30 and 100 kg body weight, carcass and meat quality of m. longissimus lumborum were studied. Analysis revealed that in both examined body weight groups, hot carcass weight, carcass yield percentage, meat content, and weight of ham and carcass ham percentage were significantly lower and backfat thickness higher for Puławska pigs compared to PLW pigs, while PLW pigs exhibited significantly longer carcasses, greater loin eye area, and, in the case of lighter pigs, smaller proportion of loin in the carcass. Muscles of Puławska pigs, in the lighter group, had higher IMF content and a* value, while in the heavier group they exhibited higher pH(45), pH(24) and a* values, lower L*, drip loss, WHC, and thermal loss compared with PLW pigs. PLW pigs had higher WB and hardness values and more glycolytic muscles characterised by higher TNF. Copyright © 2014 Elsevier Ltd. All rights reserved.

Water-quality parameters and benthic algal communities at selected streams in Minnesota, August 2000 - Study design, methods and data

USGS Publications Warehouse

Lee, K.E.

2002-01-01

This report describes the study design, sampling methods, and summarizes the physical, chemical, and benthic algal data for a component of the multiagency study that was designed to document diurnal water-quality measurements (specific conductance, pH, water temperature, and dissolved oxygen), benthic algal community composition and chlorophyll-a content, and primary productivity at 12 stream sites on 6 streams in Minnesota during August 2000. Specific conductance, pH, water temperature, dissolved oxygen concentrations and percent dissolved oxygen saturation measurements were made with submersible data recorders at 30 minute intervals for a period of 3-6 days during August 2000. Benthic algae collected from wood and rock substrate were identified and enumerated. Biovolume (volume of algal cells per unit area), density (number of cells per unit area), and chlorophyll-a content from benthic algae were determined. These data can be used as part of the multiagency study to develop an understanding of the relations among nutrient concentrations, algal abundance, algal community composition, and primary production and respiration processes in rivers of differing ecoregions in Minnesota.

Assessment of heavy metals in loose deposits in drinking water distribution system.

PubMed

Liu, Quanli; Han, Weiqiang; Han, Bingjun; Shu, Min; Shi, Baoyou

2018-06-09

Heavy metal accumulation and potential releases from loose deposits in drinking water distribution system (DWDS) can have critical impacts on drinking water safety, but the associated risks have not been sufficiently evaluated. In this work, the potential biological toxicity of heavy metals in loose deposits was calculated based on consensus-based sediment quality guidelines, and the effects of some of the main water quality parameters, such as the pH and bicarbonate and phosphate content, on the release behaviors of pre-accumulated heavy metals were investigated. The results showed that heavy metals (Cu, As, Cr, Pb, and Cd) significantly accumulated in all the samples, but the contents of the heavy metals were multiple magnitudes lower than the Fe and Mn contents. The potential biotoxicity of As and Cu was relatively high, but the biotoxicity of Cd was negligible. The water quality can significantly influence the release of heavy metals from loose deposits. As the pH increased from 7.0 to 9.0, the release of As and Cr obviously increased. The release of As, Cu, Pb, and Cr also accelerated with the addition of phosphate (from 1 to 5 mg/L). In contrast to the trends for the pH and phosphate, variations in the bicarbonate content did not have a significant influence on the release of As and Cr. The release ratios of heavy metals in the samples were very low, and there was not a correlation between the release rate of the heavy metals in the loose deposits and their potential biotoxicity.

Evaluations of groundwater contamination by leachates around Olusosun open dumpsite in Lagos metropolis, southwest Nigeria.

PubMed

Aboyeji, Olatunji Sunday; Eigbokhan, Stephen Femi

2016-12-01

A major cause of groundwater pollution in urban areas is contamination by leachates emanating from municipal solid waste dumpsites. The study evaluated the quality of water of selected boreholes and wells around Olusosun open solid waste dumpsite in Lagos metropolis, using water quality index (WQI) rating and geospatial techniques. Water samples were randomly collected from fifteen boreholes and five wells downslopes of the dumpsite. The samples were analysed for the physico-chemical parameters and heavy metals. Factor Analysis was employed to analyse the information content of the water quality indicators to determine their appropriateness for indexing. The spatial distribution of the WQIs determined using Inverse Distance Weighting (IDW) interpolation procedure. Results showed that the waters were generally acidic with 85% of pH values below the range suggested by WHO for drinking water. All samples contained concentration of dissolved oxygen (DO) in quantities higher than the recommended limit of 2.0 mg/l (average = 4.97 mg/l), while 40% of the samples contained concentration of K above the recommended limit. The concentration of heavy metals was generally low. The major cations (Mg, Na, and K) were highly positively correlated, and were positively correlated with pH, TA, TAL, TH and Cl. Negative correlations were observed between TDS, NO3(-) and PO4(3-); NO3(-) and Ag; and DO with the heavy metals. Eighteen parameters consisting of pH, EC, TDS, TA, TAL, TH, Cl, NO3(-), PO4(3-), Mg, Na, K, Zn, Mn, Fe, Cd, Ag and Pb were found to be the main indicators of groundwater pollution caused by landfill leachate percolation. Evaluation of the WQIs indicated that 35% of the water samples were unsuitable for consumption, while 15%, 15% and 35% were in the good, very good and excellent categorises, respectively. The degree of suitability of the borehole and well waters was closely related to proximity to the dumpsite. It is imperative that appropriate remediation strategies are adopted to forestall further contamination of the groundwater by leachates in the area. Copyright © 2016 Elsevier Ltd. All rights reserved.

Determination of the parameters controlling swelling of chemically cross-linked pH-sensitive poly(N-vinylimidazole) hydrogels.

PubMed

Molina, M Jesús; Gómez-Antón, M Rosa; Piérola, Inés F

2007-10-25

The number of variables controlling the behavior of ionic gels is large and very often some of them are unknown. The aim of this work is to interpret quantitatively the swelling behavior of pH sensitive gels, with the minimum number of simplifying assumptions. With this purpose, the equilibrium degree of swelling (S) and protonation (alpha) of chemically cross-linked poly(N-vinylimidazole) (PVI) immersed in aqueous salt solutions were measured as a function of the ionic strength (mu), in the whole range of pH. In acid solutions with pH in the range 0 to 4, imidazole moieties become protonated, and PVI behaves as a polyelectrolyte gel: S decreases upon increasing mu both for NaCl and for CaCl(2), with HCl as protonating acid. In aqueous solutions with larger pH, between 4 and 12, the hydrogel is practically neutral, and S increases as mu rises, showing a salting-in effect. From the quantitative analysis of these results, the following facts emerged. Protonation induces chain stiffness (as measured by the non-Gaussian factor) and worsening of the solvent quality of the aqueous media (as measured by the polymer-solvent interaction parameter). For alpha below 33%, swelling seems to be governed by the excess of mobile counterions inside the gel with respect to the bath, with a minor but still significantly negative contribution of the osmotic swelling pressure due to polymer-solvent mixing. Above 33% protonation, it is necessary to consider Manning counterion condensation to get parameters with physical meaning. The crossover between polyelectrolyte and salting-in effects corresponds to alpha and mu values with the same ionic and mixing contributions to the osmotic swelling pressure. The formation of ionic nonpermanent cross-links, with H(2)SO(4) as the protonating acid, was discarded.

Optimization of erythritol and glycerol accumulation in conidia of Beauveria bassiana by solid-state fermentation, using response surface methodology.

PubMed

Tarocco, Federico; Lecuona, Roberto E; Couto, Alicia S; Arcas, Jorge A

2005-09-01

Entomopathogenic fungi are widely produced for use as mycoinsecticides. Therefore, improvement of the shelf life of fungal propagules under good and adverse conditions should be a pre-requisite of their production. In order to improve conidial physiology as well as mycoinsecticide efficiency, culture conditions may be varied. The Doehlert design was used to generate response surfaces with an estimation of the parameters of the quadratic model allowing the study of three different factors at a different number of levels. This experimental design was applied to optimize water activity (aw), pH, and fermentation time for Beauveria bassiana conidial production and accumulation of polyols in solid-state fermentation. Thus, it was possible to identify the region in the experimental range in which the optimum values of these parameters were simultaneously achieved. Maximal conidia production was achieved at pH 5-6 and aw=0.999. Under these conditions, polyol accumulation was 3 mg erythritol/g conidia and 29.6 mg glycerol/g conidia. However, maximal polyol accumulation was achieved at pH 4.5 and aw 0.950; erythritol production increased 33-fold and glycerol production 4.5-fold. Under these conditions conidia production was 1,000 times lower. The possibilities of increasing the quality of the biocontrol agent without neglecting yield are discussed.

Determination of Aluminium and Physicochemical Parameters in the Palm Oil Estates Water Supply at Johor, Malaysia

PubMed Central

Siti Farizwana, M. R.; Mazrura, S.; Zurahanim Fasha, A.; Ahmad Rohi, G.

2010-01-01

The study was to determine the concentration of aluminium (Al) and study the physicochemical parameters (pH, total dissolved solids (TDS), turbidity, and residual chlorine) in drinking water supply in selected palm oil estates in Kota Tinggi, Johor. Water samples were collected from the estates with the private and the public water supplies. The sampling points were at the water source (S), the treatment plant outlet (TPO), and at the nearest houses (H1) and the furthest houses (H2) from the TPO. All estates with private water supply failed to meet the NSDWQ for Al with mean concentration of 0.99 ± 1.52 mg/L. However, Al concentrations in all public water supply estates were well within the limit except for one estate. The pH for all samples complied with the NSDWQ except from the private estates for the drinking water supply with an acidic pH (5.50 ± 0.90). The private water supply showed violated turbidity value in the drinking water samples (14.2 ± 24.1 NTU). Insufficient amount of chlorination was observed in the private water supply estates (0.09 ± 0.30 mg/L). Private water supplies with inefficient water treatment served unsatisfactory drinking water quality to the community which may lead to major health problems. PMID:21461348

Biological and functional responses of in situ bioassays with Chironomus riparius larvae to assess river water quality and contamination.

PubMed

Faria, Mafalda S; Ré, Ana; Malcato, João; Silva, Paula C L D; Pestana, João; Agra, Ana R; Nogueira, António J A; Soares, Amadeu M V M

2006-12-01

Single species responses have the potential to measure impacts at earlier stages than more traditional methods based in community structure. This study evaluates a bioassay with biological (survival, development, growth) and functional (post-exposure feeding rate) responses of Chironomus riparius larvae to assess water quality and contamination in rivers. The bioassay with C. riparius third instar larvae was performed, in autumn and spring, in reference sites and in organic and metal contaminated sites in Portuguese rivers. Biotic, physical and chemical parameters were determined for each site. The relationship between both bioassays responses and biotic indices (IBMWP and IASPT) and the physical and chemical parameters of respective sites were determined. In general biotic indices were able to discriminate between contaminated and not contaminated sites although they demonstrated a poor ability to detect low level of metal contamination during autumn. IASPT was negatively related to ammonia concentrations in both seasons. No significant differences in survival and post-exposure feeding rate were found between sites. Development was inhibited in the most metal contaminated site during autumn, but pH and ammonia concentrations in water accounted for 82% of developmental variation during this season. Growth was highly inhibited in the most metal contaminated site during both seasons. In autumn, growth was also inhibited in the low metal contaminated site and, during this season, pH and Mn and Fe concentrations in water samples accounted for 97% of growth variation between sites. The results suggest that in situ bioassay with C. riparius larvae using growth as the endpoint is a responsive and suitable tool that can be used as bioindicator of metal pollution and to biomonitor water quality in metal contaminated rivers.

Crystallization and evaluation of hen egg-white lysozyme crystals for protein pH titration in the crystalline state

PubMed Central

Iwai, Wakari; Yagi, Daichi; Ishikawa, Takuya; Ohnishi, Yuki; Tanaka, Ichiro; Niimura, Nobuo

2008-01-01

To observe the ionized status of the amino acid residues in proteins at different pH (protein pH titration in the crystalline state) by neutron diffraction, hen egg-white lysozyme was crystallized over a wide pH range (2.5–8.0). Crystallization phase diagrams at pH 2.5, 6.0 and 7.5 were determined. At pH < 4.5 the border between the metastable region and the nucleation region shifted to the left (lower precipitant concentration) in the phase diagram, and at pH > 4.5 the border shifted to the right (higher precipitant concentration). The qualities of these crystals were characterized using the Wilson plot method. The qualities of all crystals at different pH were more or less equivalent (B-factor values within 25–40). It is expected that neutron diffraction analysis of these crystals of different pH provides equivalent data in quality for discussions of protein pH titration in the crystalline state of hen egg-white lysozyme. PMID:18421167

Crystallization and evaluation of hen egg-white lysozyme crystals for protein pH titration in the crystalline state.

PubMed

Iwai, Wakari; Yagi, Daichi; Ishikawa, Takuya; Ohnishi, Yuki; Tanaka, Ichiro; Niimura, Nobuo

2008-05-01

To observe the ionized status of the amino acid residues in proteins at different pH (protein pH titration in the crystalline state) by neutron diffraction, hen egg-white lysozyme was crystallized over a wide pH range (2.5-8.0). Crystallization phase diagrams at pH 2.5, 6.0 and 7.5 were determined. At pH < 4.5 the border between the metastable region and the nucleation region shifted to the left (lower precipitant concentration) in the phase diagram, and at pH > 4.5 the border shifted to the right (higher precipitant concentration). The qualities of these crystals were characterized using the Wilson plot method. The qualities of all crystals at different pH were more or less equivalent (B-factor values within 25-40). It is expected that neutron diffraction analysis of these crystals of different pH provides equivalent data in quality for discussions of protein pH titration in the crystalline state of hen egg-white lysozyme.

Hydrogeochemical features of surface water and groundwater contaminated with acid mine drainage (AMD) in coal mining areas: a case study in southern Brazil.

PubMed

Galhardi, Juliana Aparecida; Bonotto, Daniel Marcos

2016-09-01

Effects of acid mine drainage (AMD) were investigated in surface waters (Laranjinha River and Ribeirão das Pedras stream) and groundwaters from a coal mining area sampled in two different seasons at Figueira city, Paraná State, Brazil. The spatial data distribution indicated that the acid effluents favor the chemical elements leaching and transport from the tailings pile into the superficial water bodies or aquifers, modifying their quality. The acid groundwaters in both sampling periods (dry: pH 2.94-6.04; rainy: pH 3.25-6.63) were probably due to the AMD generation and infiltration, after the oxidation of sulfide minerals. Such acid effluents cause an increase of the solubilization rate of metals, mainly iron and aluminum, contributing to both groundwater and surface water contamination. Sulfate in high levels is a result of waters' pollution due to AMD. In some cases, high sulfate and low iron contents, associated with less acidic pH values, could indicate that AMD, previously generated, is nowadays being neutralized. The chemistry of the waters affected by AMD is controlled by the pH, sulfide minerals' oxidation, oxygen, iron content, and microbial activity. It is also influenced by seasonal variations that allow the occurrence of dissolution processes and the concentration of some chemical elements. Under the perspective of the waters' quality evaluation, the parameters such as conductivity, dissolved sodium, and sulfate concentrations acted as AMD indicators of groundwaters and surface waters affected by acid effluents.

Immunomodulatory effects of temperature and pH of water in an Indian freshwater sponge.

PubMed

Mukherjee, Soumalya; Bhunia, Anindya Sundar; Bhunia, Niladri Sekhar; Ray, Mitali; Ray, Sajal

2016-07-01

Eunapius carteri, a freshwater sponge of India, inhabits the ponds and lakes and experiences variations of temperature and pH of water throughout the year. Sponges bear evolutionary and ecological importance with limited information on their immunological attribute and adaptational resilience in a changing environment. This paper reports temperature and pH specific responses of immune related parameters in sponge maintained in the experimental conditions of laboratory. Innate immunological parameters like phagocytosis and generation of cytotoxic molecules like superoxide anion, nitric oxide and phenoloxidase activity were estimated in E. carteri at different environmentally realistic water temperatures (10, 20, 30 and 40°C) and pH (6.4, 7.4 and 8.4). Phagocytosis and cytotoxicity are established as important immune parameters of invertebrates. Calalase, an antioxidant enzyme and phosphatases are involved in pathogen destruction and are considered as components of innate immunity. Activities of catalase, acid and alkaline phosphatases were estimated in E. carteri at different thermal regimes and pH. Modulation of phagocytic and cytotoxic responses and the activities of catalase and phosphatases at different water temperatures and pH indicated temperature and pH specific immunological status of E. carteri. Present investigation deals with the effects of selected hydrological parameters on the fundamental immune related parameters in sponge indicating its adaptational plasticity. Immunological resilience of this species in the face of variation of water temperature and pH is thought to be a special adaptive feature of sponge, a reported "living fossil". Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of quality-by-design approach to optimize diallyl disulfide-loaded solid lipid nanoparticles.

PubMed

Talluri, Siddhartha Venkata; Kuppusamy, Gowthamarajan; Karri, Veera Venkata Satyanarayana Reddy; Yamjala, Karthik; Wadhwani, Ashish; Madhunapantula, SubbaRao V; Pindiprolu, Saikiran S S

2017-05-01

The current work was carried out by the principles of quality-by-design approach to develop an optimized solid lipid nanoparticles (SLNs) formulation of diallyl disulfide (DADS) through systematic statistical study. And its antitumor activity of DADS was also evaluated on breast cancer cell lines. To understand the effect of formulation variables (critical parameters) on the responses (critical quality attributes) of SLN, a 3-factor, 3-level Box-Behnken design, was explored to predict the responses such as particle size (Y1) and % entrapment efficiency (EE) (Y2) when concentration of surfactant (X1), amount of lipid (X2), and volume of solvent (X3) were selected as independent variables. Particle size analysis revealed that all the batches were within the nanometer range. DADS was released from the SLN much more rapidly at pH 4.5 than at pH 7.4, which is a desirable characteristic for tumor-targeted drug delivery. The cytotoxicity, reactive oxygen species (ROS), determination revealed that the antitumor activity of DADS is enhanced with SLN compared to DADS-free drug, and apoptosis is the mechanism underlying the cytotoxicity. The present study indicated the remarkable potential of DADS-SLN in enhancing the anticancer effect of DADS in breast cancer cells in vitro.

Assessing quality of Medicago sativa silage by monitoring bacterial composition with single molecule, real-time sequencing technology and various physiological parameters

PubMed Central

Bao, Weichen; Mi, Zhihui; Xu, Haiyan; Zheng, Yi; Kwok, Lai Yu; Zhang, Heping; Zhang, Wenyi

2016-01-01

The present study applied the PacBio single molecule, real-time sequencing technology (SMRT) in evaluating the quality of silage production. Specifically, we produced four types of Medicago sativa silages by using four different lactic acid bacteria-based additives (AD-I, AD-II, AD-III and AD-IV). We monitored the changes in pH, organic acids (including butyric acid, the ratio of acetic acid/lactic acid, γ-aminobutyric acid, 4-hyroxy benzoic acid and phenyl lactic acid), mycotoxins, and bacterial microbiota during silage fermentation. Our results showed that the use of the additives was beneficial to the silage fermentation by enhancing a general pH and mycotoxin reduction, while increasing the organic acids content. By SMRT analysis of the microbial composition in eight silage samples, we found that the bacterial species number and relative abundances shifted apparently after fermentation. Such changes were specific to the LAB species in the additives. Particularly, Bacillus megaterium was the initial dominant species in the raw materials; and after the fermentation process, Pediococcus acidilactici and Lactobacillus plantarum became the most prevalent species, both of which were intrinsically present in the LAB additives. Our data have demonstrated that the SMRT sequencing platform is applicable in assessing the quality of silage. PMID:27340760

Assessing quality of Medicago sativa silage by monitoring bacterial composition with single molecule, real-time sequencing technology and various physiological parameters.

PubMed

Bao, Weichen; Mi, Zhihui; Xu, Haiyan; Zheng, Yi; Kwok, Lai Yu; Zhang, Heping; Zhang, Wenyi

2016-06-24

The present study applied the PacBio single molecule, real-time sequencing technology (SMRT) in evaluating the quality of silage production. Specifically, we produced four types of Medicago sativa silages by using four different lactic acid bacteria-based additives (AD-I, AD-II, AD-III and AD-IV). We monitored the changes in pH, organic acids (including butyric acid, the ratio of acetic acid/lactic acid, γ-aminobutyric acid, 4-hyroxy benzoic acid and phenyl lactic acid), mycotoxins, and bacterial microbiota during silage fermentation. Our results showed that the use of the additives was beneficial to the silage fermentation by enhancing a general pH and mycotoxin reduction, while increasing the organic acids content. By SMRT analysis of the microbial composition in eight silage samples, we found that the bacterial species number and relative abundances shifted apparently after fermentation. Such changes were specific to the LAB species in the additives. Particularly, Bacillus megaterium was the initial dominant species in the raw materials; and after the fermentation process, Pediococcus acidilactici and Lactobacillus plantarum became the most prevalent species, both of which were intrinsically present in the LAB additives. Our data have demonstrated that the SMRT sequencing platform is applicable in assessing the quality of silage.

Normal 24-hour ambulatory proximal and distal gastroesophageal reflux parameters in Chinese.

PubMed

Hu, W H C; Wong, N Y H; Lai, K C; Hui, W M; Lam, K F; Wong, B C Y; Xia, H H X; Chan, C K; Chan, A O O; Wong, W M; Tsang, K W T; Lam, S K

2002-06-01

To quantify normal proximal and distal oesophageal acid parameters in healthy Chinese. Observational study. University teaching hospital, Hong Kong. Twenty healthy adults who were not on medication and were free from gastrointestinal symptoms were recruited by advertisement. Ambulatory oesophageal acid (pH<4) exposure parameters were recorded at distal and proximal sites, 5 and 20 cm, respectively above the lower oesophageal sphincter. The 95th percentile for reflux parameters assessed in the distal/proximal oesophagus were: percent total time pH<4, 4.6/0.7%; percent upright time pH<4, 7.0/1.1%; percent supine time pH<4, 4.5/0.5%; number of reflux episodes, 73/12; number of reflux episodes with pH<4 for >5 minutes, 4/0; and the longest single acid exposure episode, 11.2/3.0 minutes. Physiological gastroesophageal reflux occurs in healthy Chinese. These initial data provide a preliminary reference range that could be utilised by laboratories studying Chinese subjects.

Assessment of Spatial and Temporal Variation of Surface Water Quality in Streams Affected by Coalbed Methane Development

NASA Astrophysics Data System (ADS)

Chitrakar, S.; Miller, S. N.; Liu, T.; Caffrey, P. A.

2015-12-01

Water quality data have been collected from three representative stream reaches in a coalbed methane (CBM) development area for over five years to improve the understanding of salt loading in the system. These streams are located within Atlantic Rim development area of the Muddy Creek in south-central Wyoming. Significant development of CBM wells is ongoing in the study area. Three representative sampling stream reaches included the Duck Pond Draw and Cow Creek, which receive co-produced water, and; South Fork Creek, and upstream Cow Creek which do not receive co-produced water. Water samples were assayed for various parameters which included sodium, calcium, magnesium, fluoride, chlorine, nitrate, O-phosphate, sulfate, carbonate, bicarbonates, and other water quality parameters such as pH, conductivity, and TDS. Based on these water quality parameters we have investigated various hydrochemical and geochemical processes responsible for the high variability in water quality in the region. However, effective interpretation of complex databases to understand aforementioned processes has been a challenging task due to the system's complexity. In this work we applied multivariate statistical techniques including cluster analysis (CA), principle component analysis (PCA) and discriminant analysis (DA) to analyze water quality data and identify similarities and differences among our locations. First, CA technique was applied to group the monitoring sites based on the multivariate similarities. Second, PCA technique was applied to identify the prevalent parameters responsible for the variation of water quality in each group. Third, the DA technique was used to identify the most important factors responsible for variation of water quality during low flow season and high flow season. The purpose of this study is to improve the understanding of factors or sources influencing the spatial and temporal variation of water quality. The ultimate goal of this whole research is to develop coupled salt loading and GIS-based hydrological modelling tool that will be able to simulate the salt loadings under various user defined scenarios in the regions undergoing CBM development. Therefore, the findings from this study will be used to formulate the predominant processes responsible for solute loading.

Investigation of acidity and other water-quality characteristics of Upper Oyster Creek, Ocean County, New Jersey

USGS Publications Warehouse

Fusillo, Thomas V.; Schornick, J.C.; Koester, H.E.; Harriman, D.A.

1980-01-01

Water-quality data collected in the upper Oyster Creek drainage basin, Ocean County, N.J., indicate that the stream has excellent water quality except for a persistently low pH. The mean concentrations of the major inorganic ions were all less than 6.0 milligrams per liter. Mean concentrations of total nitrogen and total phosphorus were 0.15 mg/L and 0.01 mg/L, respectively. Dissolved oxygen averaged 8.7 mg/L and 81% saturation. Low pH levels are typical of streams draining cedar swamps. In Oyster Creek, the pH tended to decrease downstream due to chemical and biological processes. The pH levels in swamps were one-half unit or more lower than the pH levels in the adjacent stream. Sharp declines in stream pH were noted during runoff periods as the result of the mixing of poorly-buffered stream water with more highly acidic water from surrounding swamp areas. The quality of ground water within the study area was similar to the quality of streamflow, except for higher iron and ammonia-nitrogen concentrations and a higher pH range of 4.9 to 6.5. Precipitation represented a major source of many chemical constituents in the ground- and surface-waters of the Oyster Creek basin. (USGS)

Quality by design: a systematic and rapid liquid chromatography and mass spectrometry method for eprosartan mesylate and its related impurities using a superficially porous particle column.

PubMed

Kalariya, Pradipbhai D; Kumar Talluri, Murali V N; Gaitonde, Vinay D; Devrukhakar, Prashant S; Srinivas, Ragampeta

2014-08-01

The present work describes the systematic development of a robust, precise, and rapid reversed-phase liquid chromatography method for the simultaneous determination of eprosartan mesylate and its six impurities using quality-by-design principles. The method was developed in two phases, screening and optimization. During the screening phase, the most suitable stationary phase, organic modifier, and pH were identified. The optimization was performed for secondary influential parameters--column temperature, gradient time, and flow rate using eight experiments--to examine multifactorial effects of parameters on the critical resolution and generated design space representing the robust region. A verification experiment was performed within the working design space and the model was found to be accurate. This study also describes other operating features of the column packed with superficially porous particles that allow very fast separations at pressures available in most liquid chromatography instruments. Successful chromatographic separation was achieved in less than 7 min using a fused-core C18 (100 mm × 2.1 mm, 2.6 μm) column with linear gradient elution of 10 mM ammonium formate (pH 3.0) and acetonitrile as the mobile phase. The method was validated for specificity, linearity, accuracy, precision, and robustness in compliance with the International Conference on Harmonization Q2 (R1) guidelines. The impurities were identified by liquid chromatography with mass spectrometry. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Short-Term Exposure of Mytilus coruscus to Decreased pH and Salinity Change Impacts Immune Parameters of Their Haemocytes

PubMed Central

Wu, Fangli; Xie, Zhe; Lan, Yawen; Dupont, Sam; Sun, Meng; Cui, Shuaikang; Huang, Xizhi; Huang, Wei; Liu, Liping; Hu, Menghong; Lu, Weiqun; Wang, Youji

2018-01-01

With the release of large amounts of CO2, ocean acidification is intensifying and affecting aquatic organisms. In addition, salinity also plays an important role for marine organisms and fluctuates greatly in estuarine and coastal ecosystem, where ocean acidification frequently occurs. In present study, flow cytometry was used to investigate immune parameters of haemocytes in the thick shell mussel Mytilus coruscus exposed to different salinities (15, 25, and 35‰) and two pH levels (7.3 and 8.1). A 7-day in vivo and a 5-h in vitro experiments were performed. In both experiments, low pH had significant effects on all tested immune parameters. When exposed to decreased pH, total haemocyte count (THC), phagocytosis (Pha), esterase (Est), and lysosomal content (Lyso) were significantly decreased, whereas haemocyte mortality (HM) and reactive oxygen species (ROS) were increased. High salinity had no significant effects on the immune parameters of haemocytes as compared with low salinity. However, an interaction between pH and salinity was observed in both experiments for most tested haemocyte parameters. This study showed that high salinity, low salinity and low pH have negative and interactive effects on haemocytes of mussels. As a consequence, it can be expected that the combined effect of low pH and changed salinity will have more severe effects on mussel health than predicted by single exposure. PMID:29559924

Spatial and temporal variability of cv. Tempranillo phenology and grape quality within the Ribera del Duero DO (Spain) and relationships with climate.

PubMed

Ramos, M C; Jones, G V; Yuste, J

2015-12-01

The aim of this work was to analyze spatial phenology and grape quality variability related to the climatic characteristics within the Ribera del Duero Designation of Origin (DO). Twenty plots planted with cv. Tempranillo and distributed within the DO were analyzed for phenology from 2004 to 2013. Grape quality parameters at ripening (berry weight, sugar content, acidity and pH, and anthocyanins) were analyzed in 26 plots for the period 2003-2013. The relationships between phenology and grape parameters with different climatic variables were confirmed with a multivariate analysis. On average, bud break was April 27(th), bloom June 17(th), and veraison August 12th. However, phenology during the time period showed high variability, with differences between years of up to 21 days for a phenology stage. The earliest dates were observed in dry years (2005, 2006, and to a lesser degree in 2009) while the later phenology dates occurred in the wettest year of the period (2008). High correlations were found between veraison date and temperature variables as well as with precipitation-evapotranspiration recorded during the bloom-veraison period. These effects tended to be higher in the central part of the DO. Grape quality parameters also showed high variability among the dry and the wet years, and the influence of extreme temperatures on color development as well as the effect of available water on acidity were observed.

Spatial and temporal variability of cv. Tempranillo phenology and grape quality within the Ribera del Duero DO (Spain) and relationships with climate

NASA Astrophysics Data System (ADS)

Ramos, M. C.; Jones, G. V.; Yuste, J.

2015-12-01

The aim of this work was to analyze spatial phenology and grape quality variability related to the climatic characteristics within the Ribera del Duero Designation of Origin (DO). Twenty plots planted with cv. Tempranillo and distributed within the DO were analyzed for phenology from 2004 to 2013. Grape quality parameters at ripening (berry weight, sugar content, acidity and pH, and anthocyanins) were analyzed in 26 plots for the period 2003-2013. The relationships between phenology and grape parameters with different climatic variables were confirmed with a multivariate analysis. On average, bud break was April 27th, bloom June 17th, and veraison August 12th. However, phenology during the time period showed high variability, with differences between years of up to 21 days for a phenology stage. The earliest dates were observed in dry years (2005, 2006, and to a lesser degree in 2009) while the later phenology dates occurred in the wettest year of the period (2008). High correlations were found between veraison date and temperature variables as well as with precipitation-evapotranspiration recorded during the bloom-veraison period. These effects tended to be higher in the central part of the DO. Grape quality parameters also showed high variability among the dry and the wet years, and the influence of extreme temperatures on color development as well as the effect of available water on acidity were observed.

Computer-Assisted Optimization of Electrodeposited Hydroxyapatite Coating Parameters on Medical Alloys

NASA Astrophysics Data System (ADS)

Coşkun, M. İbrahim; Karahan, İsmail H.; Yücel, Yasin; Golden, Teresa D.

2016-04-01

CoCrMo bio-metallic alloys were coated with a hydroxyapatite (HA) film by electrodeposition using various electrochemical parameters. Response surface methodology and central composite design were used to optimize deposition parameters such as electrolyte pH, deposition potential, and deposition time. The effects of the coating parameters were evaluated within the limits of solution pH (3.66 to 5.34), deposition potential (-1.13 to -1.97 V), and deposition time (6.36 to 73.64 minutes). A 5-level-3-factor experimental plan was used to determine ideal deposition parameters. Optimum conditions for the deposition parameters of the HA coating with high in vitro corrosion performance were determined as electrolyte pH of 5.00, deposition potential of -1.8 V, and deposition time of 20 minutes.

Comparison of Carcass Characteristics, Meat Quality, and Blood Parameters of Slow and Fast Grown Female Broiler Chickens Raised in Organic or Conventional Production System

PubMed Central

Cömert, Muazzez; Şayan, Yılmaz; Kırkpınar, Figen; Bayraktar, Ö. Hakan; Mert, Selim

2016-01-01

The objective of the study was to compare the carcass characteristics, meat quality, and blood parameters of slow and fast grown female broiler chickens fed in organic or conventional production system. The two genotypes tested were medium slow-growing chickens (SG, Hubbard Red JA) and commercial fast-growing chickens (FG, Ross 308). Both genotypes (each represented by 400 chickens) were divided into two sub-groups fed either organic (O) or conventional (C) systems. Chickens of each genotype and system were raised in a semi environmentally controlled poultry house until 21 d of age and were assigned to 5 pens of 40 chickens each. Then, O system chickens were transferred into an open-side poultry house with an outdoor run. At 81 d of age, 10 female chickens from each genotype and from each production system (n = 40) were randomly chosen to provide material for analysis, and were weighed and brought to the slaughterhouse to assess carcass characteristics and meat quality. The blood parameters were determined by using 5 female chickens from each genotype and from each production system (n = 20). FG had the higher live weight, along with carcass, breast, and thigh-drumstick weights compared to SG (p<0.05). FG had the higher breast yield, whereas SG had the higher thigh-drumstick yield (p<0.05). The O system resulted in a higher amount of abdominal fat (p<0.05). In addition, the O system values were higher for dry matter, crude ash, crude protein, and pH15 values in breast meat, and for crude ash, crude protein, and pH15 values in drumstick meat (p<0.05). In addition, total saturated fatty acids, total mono-unsaturated fatty acids, and total omega 3 were significantly higher in the O system than in the C system. Thus, the O system showed a positive advantage compared to the C system regarding female chicken meat quality, primarily within the ash, protein, and total omega 3 fatty acid profiles. In conclusion, the present study indicated that the main factor affecting the carcass characteristics of female chickens was genotype, whereas the organic system contributed to enhanced meat quality. These findings provide a better understanding of the relative roles of genotype and production systems in female broiler characteristics, and might aid producers in designing their facilities to optimize yield and quality while maintaining acceptable animal welfare standards. PMID:26954206

Survey of trace metals in drinking water supplied to rural populations in the eastern Llanos of Venezuela.

PubMed

Mora, Abrahan; Mac-Quhae, César; Calzadilla, Malvis; Sánchez, Luzmila

2009-02-01

To ascertain the water quality for human consumption, chemical parameters such as pH, conductivity and total dissolved calcium, magnesium, iron, aluminum, zinc, copper and manganese were measured during four sampling periods (November 2002; March, May and July 2003) in drinking water wells which supply several forest camps and rural populations located in the eastern Llanos of Venezuela. Copper levels in drinking water in November 2002 were found to be significantly higher (P<0.05) than the other assessed periods. Temporal variations of the other parameters considered were not statistically significant. Calcium and magnesium concentrations were found to be extremely low (mean concentration+/-S.D. of 0.27+/-0.25mg/l for Ca and 0.219+/-0.118 for Mg) during the four sampling periods, probably because of the carbonate bearing scarcity in the soils lithic component. The rest of the metals complied with the Venezuelan and International guidelines of quality criteria for drinking water.

Modified atmosphere packaging of precooked vegetables: effect on physicochemical properties and sensory quality.

PubMed

Barbosa, Carla; Alves, M Rui; Rocha, Susana; Oliveira, M Beatriz P P

2016-03-01

This study aims at verifying the effect of three modified atmosphere packaging (MAP) conditions, all with high CO2 and residual or low O2 contents (%O2/%CO2: 0/40; 2.5/40 and 2.5/60), on the quality preservation of several species of precooked vegetables (cabbage, carrots, green beans and bell peppers). The study was carried out for different storage periods (up to 28 days and 6 sampling periods). Physicochemical parameters (pH, acidity, moisture and ash contents, antioxidant activity, colour, and texture), microbial growth, organoleptic properties and consumer acceptability were assessed. Concerning physicochemical parameters and microbial growth only slight changes without any consistent tendency were observed. This was also confirmed by the trained panel that could not discriminate samples with different storage times. Best preservation conditions were obtained with 0%O2/40%CO2, promoting a shelf life extension of almost 12 days more comparing to commercial conditions presently used. Copyright © 2015 Elsevier Ltd. All rights reserved.

Non-thermal combined treatments in the processing of açai (Euterpe oleracea) juice.

PubMed

Oliveira, Ana Flávia A; Mar, Josiana M; Santos, Samara F; da Silva Júnior, Joel L; Kluczkovski, Ariane M; Bakry, Amr M; Bezerra, Jaqueline de Araújo; Nunomura, Rita de Cássia Saraiva; Sanches, Edgar A; Campelo, Pedro H

2018-11-01

Quality parameters of açai juice processed with ultrasound-assisted, ozone and the combined methods were analyzed in this work. Two ultrasound energy densities (350 and 700 J·mL -1 ) and two ozonization times (5 and 10 min with 1.5 ppm) were analyzed for pure açai juice and 8 different treatments (2 2 complete factorial). To evaluate the quality parameters of the juice, physical-chemical analyzes such as pH, titratable acidity, cloud value, non-enzymatic browning, rheology, antioxidant activity (DPPH and ABTS), phenolic compounds, anthocyanins, enzymatic activity (peroxidase and polyphenol oxidase) and microbial counts (mesophilic bacteria, molds and yeasts) were conducted. The treatments with ozone were better for microbial inactivation and the ultrasound for enzymatic inactivation. In general, the use of non-thermal methods can be a good alternative for the processing of açai juice. Copyright © 2018 Elsevier Ltd. All rights reserved.

Marine ecological habitat: a case study on projected thermal power plant around Dharamtar Creek, India.

PubMed

Kulkarni, Vikrant A; Naidu, Velamala S; Jagtap, Tanaji G

2011-03-01

Estuaries and tidal creeks, harboring mangroves particularly, face tremendous anthropogenic pressures. Expansion of mega cities and the thermal power plants are generally proposed in the vicinity of estuaries and creek, due to the feasibility of intake and discharge of water for cooling. Discharges from such developments remain constant threat of increasing thermal pollution and affecting the quality of environment. The baseline information on prevailing quality of aquatic environment comes handy for understanding alterations due to such activities. Principle component analysis (PCA) revealed that temperature, pH, salinity, suspended solids, DO, BOD and phaeophytins are major parameters influencing the creek system. Heated effluents may have direct and adverse impacts on these parameters, altering biotic constituents. Hence, periodic and detailed observations are necessary to estimate exact response of biotic communities to changing environment. The present paper is based on case study, projecting a power plant in the vicinity of major mangrove habitats of Dharamtar creek.

Monitoring and evaluation of the water quality of Budeasa Reservoir-Arges River, Romania.

PubMed

Ion, Antoanela; Vladescu, Luminita; Badea, Irinel Adriana; Comanescu, Laura

2016-09-01

The purpose of this study was to monitor and record the specific characteristics and properties of the Arges River water in the Budeasa Reservoir (the principal water resources of municipal tap water of the big Romanian city Pitesti and surrounding area) for a period of 5 years (2005-2009). The monitored physical and chemical parameters were turbidity, pH, electrical conductivity, chemical oxygen demand, 5 days biochemical oxygen demand, free dissolved oxygen, nitrite, nitrate, ammonia nitrogen, chloride, total dissolved iron ions, sulfate, manganese, phosphate, total alkalinity, and total hardness. The results were discussed in correlation with the precipitation values during the study. Monthly and annual values of each parameter determined in the period January 2005-December 2009 were used as a basis for the classification of Budeasa Reservoir water, according to the European legislation, as well as for assessing its quality as a drinking water supply. Principal component analysis and Pearson correlation coefficients were used as statistical procedures in order to evaluate the data obtained during this study.

Physicochemical characterization of pure persimmon juice: nutritional quality and food acceptability.

PubMed

González, Eva; Vegara, Salud; Martí, Nuria; Valero, Manuel; Saura, Domingo

2015-03-01

Technological process for production of non-astringent persimmon (Diospyros kaki Thunb. cv. "Rojo Brillante") juice was described. The degree of fruit ripening expressed as color index (CI) varied between 12.37 and 16.33. Persimmon juice was characterized by determining physicochemical quality parameters as yield, total soluble solids (TSS), pH, titratable acidity (TA), organic acids, and main sugars. A thermal treatment of 90 ºC for 10 s was effective in controlling naturally occurring microorganisms for at least 105 d of storage without significantly affecting production of soluble brown pigments (BPs) and 5-hydroxymethyl furfural (5-HMF), total phenolic compounds (TPC), antioxidant capacity and acceptability of juice by panelists. Storage time affected all and each of the above parameters, reducing BPs, TPC and antioxidant capacity but increasing 5-HMF content. Refrigerated storage enhanced the acceptability of the juices. This information may be used by the juice industry as a starting point for production of pure persimmon juices. © 2015 Institute of Food Technologists®

Direct injection analysis of fatty and resin acids in papermaking process waters by HPLC/MS.

PubMed

Valto, Piia; Knuutinen, Juha; Alén, Raimo

2011-04-01

A novel HPLC-atmospheric pressure chemical ionization/MS (HPLC-APCI/MS) method was developed for the rapid analysis of selected fatty and resin acids typically present in papermaking process waters. A mixture of palmitic, stearic, oleic, linolenic, and dehydroabietic acids was separated by a commercial HPLC column (a modified stationary C(18) phase) using gradient elution with methanol/0.15% formic acid (pH 2.5) as a mobile phase. The internal standard (myristic acid) method was used to calculate the correlation coefficients and in the quantitation of the results. In the thorough quality parameters measurement, a mixture of these model acids in aqueous media as well as in six different paper machine process waters was quantitatively determined. The measured quality parameters, such as selectivity, linearity, precision, and accuracy, clearly indicated that, compared with traditional gas chromatographic techniques, the simple method developed provided a faster chromatographic analysis with almost real-time monitoring of these acids. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Relevance of water quality index for groundwater quality evaluation: Thoothukudi District, Tamil Nadu, India

NASA Astrophysics Data System (ADS)

Singaraja, C.

2017-09-01

The present hydrogeochemical study was confined to the Thoothukudi District in Tamilnadu, India. A total of 100 representative water samples were collected during pre-monsoon and post-monsoon and analyzed for the major cations (sodium, calcium, magnesium and potassium) and anions (chloride, sulfate, bicarbonate, fluoride and nitrate) along with various physical and chemical parameters (pH, total dissolved salts and electrical conductivity). Water quality index rating was calculated to quantify the overall water quality for human consumption. The PRM samples exhibit poor quality in greater percentage when compared with POM due to dilution of ions and agricultural impact. The overlay of WQI with chloride and EC corresponds to the same locations indicating the poor quality of groundwater in the study area. Sodium (Na %), sodium absorption ratio (SAR), residual sodium carbonate (RSC), residual sodium bicarbonate, permeability index (PI), magnesium hazards (MH), Kelly's ratio (KR), potential salinity (PS) and Puri's salt index (PSI) and domestic quality parameters such as total hardness (TH), temporary, permanent hardness and corrosivity ratio (CR) were calculated. The majority of the samples were not suitable for drinking, irrigation and domestic purposes in the study area. In this study, the analysis of salinization/freshening processes was carried out through binary diagrams such as of mole ratios of {SO}_{ 4}^{ 2- } /Cl- and Cl-/EC that clearly classify the sources of seawater intrusion and saltpan contamination. Spatial diagram BEX was used to find whether the aquifer was in the salinization region or in the freshening encroachment region.

Application of visible/near infrared spectroscopy to quality control of fresh fruits and vegetables in large-scale mass distribution channels: a preliminary test on carrots and tomatoes.

PubMed

Beghi, Roberto; Giovenzana, Valentina; Tugnolo, Alessio; Guidetti, Riccardo

2018-05-01

The market for fruits and vegetables is mainly controlled by the mass distribution channel (MDC). MDC buyers do not have useful instruments to rapidly evaluate the quality of the products. Decisions by the buyers are driven primarily by pricing strategies rather than product quality. Simple, rapid and easy-to-use methods for objectively evaluating the quality of postharvest products are needed. The present study aimed to use visible and near-infrared (vis/NIR) spectroscopy to estimate some qualitative parameters of two low-price products (carrots and tomatoes) of various brands, as well as evaluate the applicability of this technique for use in stores. A non-destructive optical system (vis/NIR spectrophotometer with a reflection probe, spectral range 450-1650 nm) was tested. The differences in quality among carrots and tomatoes purchased from 13 stores on various dates were examined. The reference quality parameters (firmness, water content, soluble solids content, pH and colour) were correlated with the spectral readings. The models derived from the optical data gave positive results, in particular for the prediction of the soluble solids content and the colour, with better results for tomatoes than for carrots. The application of optical techniques may help MDC buyers to monitor the quality of postharvest products, leading to an effective optimization of the entire supply chain. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Low pH affects survival, growth, size distribution, and carapace quality of the postlarvae and early juveniles of the freshwater prawn Macrobrachium rosenbergii de Man

NASA Astrophysics Data System (ADS)

Kawamura, Gunzo; Bagarinao, Teodora; Yong, Annita Seok Kian; Chen, Chiau Yu; Noor, Siti Norasidah Mat; Lim, Leong Seng

2015-06-01

Acidification of rain water caused by air pollutants is now recognized as a serious threat to aquatic ecosystems. We examined the effects of low pH (control pH 7.5, pH 6, pH 5, pH 4) on the survival, growth, and shell quality of Macrobrachium rosenbergii postlarvae and early juveniles in the laboratory. Hatcheryproduced postlarvae (PL 5) were stocked at 250 PL per aquarium, acclimated over 7 d to experimental pH adjusted with hydrochloric acid, and reared for 30 d. Dead specimens were removed and counted twice a day. After 27 d rearing, all specimens were measured for total length and body weight. Carapace quality was assessed by spectrophotometry. Survival of juveniles was highest at pH 6 (binomial 95% confidence interval 79 - 89%) followed by control pH 7.5 (56 - 68%) and pH 5 (50 - 60%) and was lowest for unmetamorphosed postlarvae and juveniles at pH 4 (43 - 49%). The final median total length and body weight of juveniles were similar at control pH 7.5 (18.2 TL, 50.2 mg BW) and pH 6 (17.7 mm TL, 45.0 mg BW) but significantly less at pH 5 (16.7 mm TL, 38.2 mg BW); at pH 4, the postlarvae did not metamorphose and measured only 9.8 mm TL, 29.3 mg BW. Length frequency distribution showed homogeneous growth at pH 6, positive skew at control pH 7.5 and pH 5, and extreme heterogeneity at pH 4. The carapace showed different transmittance spectra and lower total transmittance (i.e. thicker carapace) in juveniles at pH 7.5, pH 6, and pH 5 than in unmetamorphosed postlarvae and juveniles with thinner carapace at pH 4. Thus, survival, growth, size distribution, and carapace quality of M. rosenbergii postlarvae and early juveniles were negatively affected by pH 5 and especially pH 4. The thinner carapace of the survivors at pH 4 was mostly due to their small size and failure to metamorphose. Natural waters affected by acid rain could decimate M. rosenbergii populations in the wild.

[Physicochemical and microbiological evaluation of 3 commercial guava jams (Psidium guajava L.)].

PubMed

López, R; Ramírez, A O; Graziani de Fariñas, L

2000-09-01

Four different production batches were taken from each brand. Samples were purchased from retail markets in Maracay, Cagua and Turmero. (Venezuela). The average physical and chemical values were: vacuum = 38.81 cm Hg; pH = 3.28; titrable acidity (%citric acid) = 0.59%; degree Brix = 67.24; reducing sugars = 55.28%; total sugars = 62.28, and the color parameters a = +14.44, b = +8.77 and L = 17.09. Molds, yeast and aerobic plate counts were lower than 10 UFC/g; it reveals an excellent microbiological quality of the product. The studied jams degree Brix and acidity fulfil COVENIN (1) requirements for jam products, but not pH range. In agreement with variance analysis, there were highly significance differences between the samples and among the shares of each sample for all physical and chemical properties evaluated.

Effect of freezing on electrical properties and quality of thawed chicken breast meat

PubMed Central

Wei, Ran; Wang, Peng; Han, Minyi; Chen, Tianhao; Xu, Xinglian; Zhou, Guanghong

2017-01-01

Objective The objective of this research was to study the electrical properties and quality of frozen-thawed chicken breast meat and to investigate the relationship between these parameters at different times of frozen storage. Methods Thawed samples of chicken breast muscles were evaluated after being kept in frozen storage at −18°C for different periods of time (1, 2, 3, 4, 5, 6, 7, and 8 months). Results The results showed that water-holding capacity (WHC) and protein solubility decreased while thiobarbituric acid-reactive substances content increased with increasing storage time. The impedance module of samples decreased during 8-month frozen storage. Pearson correlation coefficients showed that the impedance change ratio (Q value) was significantly (p<0.05) related to pH, color, WHC, lipid oxidation and protein solubility, indicating a good relationship between the electrical properties and qualities of frozen-thawed chicken breast meat. Conclusion Impedance measurement has a potential to assess the quality of frozen chicken meat combining with quality indices. PMID:27554358

Cluster analysis application in research on pork quality determinants

NASA Astrophysics Data System (ADS)

Przybylski, W.; Wasiewicz, P.; Zieliński, P.; Gromadzka-Ostrowska, J.; Olczak, E.; Jaworska, D.; Niemyjski, S.; Santé-Lhoutellier, V.

2010-09-01

In this paper data mining methods were applied to investigate features determining high quality pork meat. The aim of the study was analysis of conditionality of the pork meat quality defined in coherence with HDL and LDL cholesterol concentration, plasma leptin, triglycerides, plasma glucose and serum. The research was carried out on 54 pigs. originated from crossbreeding of Naima sows with P76-PenArLan boars hybrids line. Meat quality parameters were evaluated in samples derived from the Longissimus (LD) muscle taken behind the last rib on the basis: the pH value, meat colour, drip loss, the RTN, intramuscular fat and glycolytic potential. The results of this study were elaborated by using R environment and show that cluster and regression analysis can be a useful tool for in-depth analysis of the determinants of the quality of pig meat in homogeneous populations of pigs. However, the question of determinants of the level of glycogen and fat in meat requires further research.

Groundwater quality around Tummalapalle area, Cuddapah District, Andhra Pradesh, India

NASA Astrophysics Data System (ADS)

Sreedhar, Y.; Nagaraju, A.

2017-11-01

The suitability of groundwater for drinking and irrigation was assessed in Tummalapalle area. Forty groundwater samples were analysed for major cations, anions and other parameters such as pH, electrical conductivity, total dissolved solids (TDS), total alkalinity and total hardness (TH). The parameters such as sodium adsorption ratio, adjusted sodium adsorption ratio (adj.SAR), per cent sodium, potential salinity, residual sodium carbonate, non-carbonate hardness, Kelly's ratio and permeability index were calculated for the evaluation of irrigation water quality. Groundwater chemistry was also analysed by statistical analysis, USSL, Wilcox, Doneen, Piper and Chadhas diagrams, to find out their suitability for irrigation. TDS and TH were used as main parameters to interpret the suitability of groundwater for drinking purpose. The correlation coefficient matrix between the hydrochemical parameters was carried out using Pearson's correlation to infer the possible water-rock interactions responsible for the variation of groundwater chemistry and this has been supported by Gibbs diagram. The results indicate that the groundwater in Tummalapalle area is alkaline in nature. Ca-Mg-HCO3 is the dominant hydrogeochemical facies. Water chemistry of the study area strongly reflects the dominance of weathering of rock-forming minerals such as bicarbonates and silicates. All parameters and diagrams suggest that the water samples of the study are good for irrigation, and the plots of TDS and TH suggest that 12.5% of the samples are good for human consumption.

Evaluation of pH monitoring as a method of processor control.

PubMed

Stears, J G; Gray, J E; Winkler, N T

1979-01-01

Sensitometry and pH values of the developer solution were compared in controlled over-replenishment, developer depletion, fixer contamination experiments, and on a daily quality control basis. The purpose of these comparisons was to evaluate the potential of pH monitoring as a method of processor control, or a supplement to sensitometry as a method of quality control. Reasonable correlation was found between pH values and film density in two of the three experiments but little or no correlation was found in the third experiment and on a day-to-day basis. The conclusion drawn from these comparisons is that pH monitoring has several limitations which render it unsuitable as a method of daily processor quality control as either a primary or supplementary technique. Sensitometry takes into account all the variables encountered in film processing and is the clear method of choice for processor quality control.

Effects of Low pH on Photosynthesis, Related Physiological Parameters, and Nutrient Profiles of Citrus

PubMed Central

Long, An; Zhang, Jiang; Yang, Lin-Tong; Ye, Xin; Lai, Ning-Wei; Tan, Ling-Ling; Lin, Dan; Chen, Li-Song

2017-01-01

Seedlings of “Xuegan” (Citrus sinensis) and “Sour pummelo” (Citrus grandis) were irrigated daily with a nutrient solution at a pH of 2.5, 3, 4, 5, or 6 for 9 months. Thereafter, the following responses were investigated: seedling growth; root, stem, and leaf concentrations of nutrient elements; leaf gas exchange, pigment concentration, ribulose-1,5-bisphosphate carboxylase/oxygenase activity and chlorophyll a fluorescence; relative water content, total soluble protein level, H2O2 production and electrolyte leakage in roots and leaves. This was done (a) to determine how low pH affects photosynthesis, related physiological parameters, and mineral nutrient profiles; and (b) to understand the mechanisms by which low pH may cause a decrease in leaf CO2 assimilation. The pH 2.5 greatly inhibited seedling growth, and many physiological parameters were altered only at pH 2.5; pH 3 slightly inhibited seedling growth; pH 4 had almost no influence on seedling growth; and seedling growth and many physiological parameters reached their maximum at pH 5. No seedlings died at any given pH. These results demonstrate that citrus survival is insensitive to low pH. H+-toxicity may directly damage citrus roots, thus affecting the uptake of mineral nutrients and water. H+-toxicity and a decreased uptake of nutrients (i.e., nitrogen, phosphorus, potassium, calcium, and magnesium) and water were likely responsible for the low pH-induced inhibition of growth. Leaf CO2 assimilation was inhibited only at pH 2.5. The combinations of an impaired photosynthetic electron transport chain, increased production of reactive oxygen species, and decreased uptake of nutrients and water might account for the pH 2.5-induced decrease in CO2 assimilation. Mottled bleached leaves only occurred in the pH 2.5-treated C. grandis seedlings. Furthermore, the pH 2.5-induced alterations of leaf CO2 assimilation, water-use efficiency, chlorophylls, polyphasic chlorophyll a fluorescence (OJIP) transients and many fluorescence parameters, root and leaf total soluble proteins, H2O2 production, and electrolyte leakage were all slightly greater in C. grandis than in C. sinensis seedlings. Hence, C. sinensis was slightly more tolerant to low pH than C. grandis. In conclusion, our findings provide novel insight into the causes of low pH-induced inhibition of seedling growth and leaf CO2 assimilation. PMID:28270819

Effects of Low pH on Photosynthesis, Related Physiological Parameters, and Nutrient Profiles of Citrus.

PubMed

Long, An; Zhang, Jiang; Yang, Lin-Tong; Ye, Xin; Lai, Ning-Wei; Tan, Ling-Ling; Lin, Dan; Chen, Li-Song

2017-01-01

Seedlings of "Xuegan" ( Citrus sinensis ) and "Sour pummelo" ( Citrus grandis ) were irrigated daily with a nutrient solution at a pH of 2.5, 3, 4, 5, or 6 for 9 months. Thereafter, the following responses were investigated: seedling growth; root, stem, and leaf concentrations of nutrient elements; leaf gas exchange, pigment concentration, ribulose-1,5-bisphosphate carboxylase/oxygenase activity and chlorophyll a fluorescence; relative water content, total soluble protein level, H 2 O 2 production and electrolyte leakage in roots and leaves. This was done ( a ) to determine how low pH affects photosynthesis, related physiological parameters, and mineral nutrient profiles; and ( b ) to understand the mechanisms by which low pH may cause a decrease in leaf CO 2 assimilation. The pH 2.5 greatly inhibited seedling growth, and many physiological parameters were altered only at pH 2.5; pH 3 slightly inhibited seedling growth; pH 4 had almost no influence on seedling growth; and seedling growth and many physiological parameters reached their maximum at pH 5. No seedlings died at any given pH. These results demonstrate that citrus survival is insensitive to low pH. H + -toxicity may directly damage citrus roots, thus affecting the uptake of mineral nutrients and water. H + -toxicity and a decreased uptake of nutrients (i.e., nitrogen, phosphorus, potassium, calcium, and magnesium) and water were likely responsible for the low pH-induced inhibition of growth. Leaf CO 2 assimilation was inhibited only at pH 2.5. The combinations of an impaired photosynthetic electron transport chain, increased production of reactive oxygen species, and decreased uptake of nutrients and water might account for the pH 2.5-induced decrease in CO 2 assimilation. Mottled bleached leaves only occurred in the pH 2.5-treated C. grandis seedlings. Furthermore, the pH 2.5-induced alterations of leaf CO 2 assimilation, water-use efficiency, chlorophylls, polyphasic chlorophyll a fluorescence (OJIP) transients and many fluorescence parameters, root and leaf total soluble proteins, H 2 O 2 production, and electrolyte leakage were all slightly greater in C. grandis than in C. sinensis seedlings. Hence, C. sinensis was slightly more tolerant to low pH than C. grandis . In conclusion, our findings provide novel insight into the causes of low pH-induced inhibition of seedling growth and leaf CO 2 assimilation.

Design of experiments reveals critical parameters for pilot-scale freeze-and-thaw processing of L-lactic dehydrogenase.

PubMed

Roessl, Ulrich; Humi, Sebastian; Leitgeb, Stefan; Nidetzky, Bernd

2015-09-01

Freezing constitutes an important unit operation of biotechnological protein production. Effects of freeze-and-thaw (F/T) process parameters on stability and other quality attributes of the protein product are usually not well understood. Here a design of experiments (DoE) approach was used to characterize the F/T behavior of L-lactic dehydrogenase (LDH) in a 700-mL pilot-scale freeze container equipped with internal temperature and pH probes. In 24-hour experiments, target temperature between -10 and -38°C most strongly affected LDH stability whereby enzyme activity was retained best at the highest temperature of -10°C. Cooling profile and liquid fill volume also had significant effects on LDH stability and affected the protein aggregation significantly. Parameters of the thawing phase had a comparably small effect on LDH stability. Experiments in which the standard sodium phosphate buffer was exchanged by Tris-HCl and the non-ionic surfactant Tween 80 was added to the protein solution showed that pH shift during freezing and protein surface exposure were the main factors responsible for LDH instability at the lower freeze temperatures. Collectively, evidence is presented that supports the use of DoE-based systematic analysis at pilot scale in the identification of F/T process parameters critical for protein stability and in the development of suitable process control strategies. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Glucose ameliorates the metabolic profile and mitochondrial function of platelet concentrates during storage in autologous plasma

PubMed Central

Amorini, Angela M.; Tuttobene, Michele; Tomasello, Flora M.; Biazzo, Filomena; Gullotta, Stefano; De Pinto, Vito; Lazzarino, Giuseppe; Tavazzi, Barbara

2013-01-01

Background It is essential that the quality of platelet metabolism and function remains high during storage in order to ensure the clinical effectiveness of a platelet transfusion. New storage conditions and additives are constantly evaluated in order to achieve this. Using glucose as a substrate is controversial because of its potential connection with increased lactate production and decreased pH, both parameters triggering the platelet lesion during storage. Materials and methods In this study, we analysed the morphological status and metabolic profile of platelets stored for various periods in autologous plasma enriched with increasing glucose concentrations (13.75, 27.5 and 55 mM). After 0, 2, 4, 6 and 8 days, high energy phosphates (ATP, GTP, ADP, AMP), oxypurines (hypoxanthine, xanthine, uric acid), lactate, pH, mitochondrial function, cell lysis and morphology, were evaluated. Results The data showed a significant dose-dependent improvement of the different parameters in platelets stored with increasing glucose, compared to what detected in controls. Interestingly, this phenomenon was more marked at the highest level of glucose tested and in the period of time generally used for platelet transfusion (0–6 days). Conclusion These results indicate that the addition of glucose during platelet storage ameliorates, in a dose-dependent manner, the biochemical parameters related to energy metabolism and mitochondrial function. Since there was no correspondence between glucose addition, lactate increase and pH decrease in our experiments, it is conceivable that platelet derangement during storage is not directly caused by glucose through an increase of anaerobic glycolysis, but rather to a loss of mitochondrial functions caused by reduced substrate availability. PMID:22682337

Effect of pre-slaughter shackling and wing flapping on plasma parameters, postmortem metabolism, AMPK, and meat quality of broilers.

PubMed

Huang, J C; Yang, J; Huang, M; Zhu, Z S; Sun, X B; Zhang, B H; Xu, X L; Meng, W G; Chen, K J; Xu, B C

2018-05-01

The objective of this study was to determine the effects of shackling and wing flapping on stress, postmortem metabolism, AMP-activated protein kinase (AMPK), and quality of broiler pectoralis major. Before slaughter, a total of 80 Arbor Acres broilers was randomly categorized into 2 replicate pens (40 broilers per pen) and each pen randomly divided into 2 groups (shackling, T; control, C). Corticosterone, creatine kinase, and lactate dehydrogenase were determined on blood plasma parameters. Pectoralis major were removed after evisceration and used for determination of energy metabolism, meat quality, and AMPK phosphorylation. In this study, shackling and wing flapping increased (P < 0.05) plasma corticosterone level, creatine kinase activity, and lactate dehydrogenase activity. Shackling and wing flapping increased (P < 0.05) AMPKα(Thr172) and acetyl-CoA carboxylase (ACC) phosphorylation, followed by rapid glycolysis and accumulation of lactic acid, and leading to a fast pH decline in the initial postmortem meat. Shackling and wing flapping have an adverse effect on final meat quality, which increased (P < 0.05) muscle lightness, drip loss, and cooking loss. The results indicate that antemortem shackling and wing flapping increased stress and AMPKα(Thr172) phosphorylation, which may accelerate glycolysis and lead to a low water-holding capacity of broiler meat.

Effects of thermal treatment and sonication on quality attributes of Chokanan mango (Mangifera indica L.) juice.

PubMed

Santhirasegaram, Vicknesha; Razali, Zuliana; Somasundram, Chandran

2013-09-01

Ultrasonic treatment is an emerging food processing technology that has growing interest among health-conscious consumers. Freshly squeezed Chokanan mango juice was thermally treated (at 90 °C for 30 and 60s) and sonicated (for 15, 30 and 60 min at 25 °C, 40 kHz frequency, 130 W) to compare the effect on microbial inactivation, physicochemical properties, antioxidant activities and other quality parameters. After sonication and thermal treatment, no significant changes occurred in pH, total soluble solids and titratable acidity. Sonication for 15 and 30 min showed significant improvement in selected quality parameters except color and ascorbic acid content, when compared to freshly squeezed juice (control). A significant increase in extractability of carotenoids (4-9%) and polyphenols (30-35%) was observed for juice subjected to ultrasonic treatment for 15 and 30 min, when compared to the control. In addition, enhancement of radical scavenging activity and reducing power was observed in all sonicated juice samples regardless of treatment time. Thermal and ultrasonic treatment exhibited significant reduction in microbial count of the juice. The results obtained support the use of sonication to improve the quality of Chokanan mango juice along with safety standard as an alternative to thermal treatment. Copyright © 2013 Elsevier B.V. All rights reserved.

Impacts of nutrients and pesticides from small- and large-scale agriculture on the water quality of Lake Ziway, Ethiopia.

PubMed

Teklu, Berhan M; Hailu, Amare; Wiegant, Daniel A; Scholten, Bernice S; Van den Brink, Paul J

2018-05-01

The area around Lake Ziway in Ethiopia is going through a major agricultural transformation with both small-scale farmers and large horticultural companies using pesticides and fertilisers at an increased rate. To be able to understand how this influences the water quality of Lake Ziway, water quality data was gathered to study the dynamics of pesticide concentrations and physicochemical parameters for the years from 2009 to 2015. Results indicate that for some physicochemical parameters, including pH, potassium and iron, over 50 % of the values were above the maximum permissible limit of the Ethiopian standard for drinking water. The fungicide spiroxamine poses a high chronic risk when the water is used for drinking water, while the estimated intake of diazinon was approximately 50 % of the acceptable daily intake. Higher-tier risk assessment indicated that the fungicide spiroxamine poses a high acute risk to aquatic organisms, while possible acute risks were indicated for the insecticides deltamethrin and endosulfan. Longer-term monitoring needs to be established to show the water quality changes across time and space, and the current study can be used as a baseline measurement for further research in the area as well as an example for other surface water systems in Ethiopia and Africa.

Water bicarbonate modulates the response of the shore crab Carcinus maenas to ocean acidification.

PubMed

Maus, Bastian; Bock, Christian; Pörtner, Hans-O

2018-05-23

Ocean acidification causes an accumulation of CO 2 in marine organisms and leads to shifts in acid-base parameters. Acid-base regulation in gill breathers involves a net increase of internal bicarbonate levels through transmembrane ion exchange with the surrounding water. Successful maintenance of body fluid pH depends on the functional capacity of ion-exchange mechanisms and associated energy budget. For a detailed understanding of the dependence of acid-base regulation on water parameters, we investigated the physiological responses of the shore crab Carcinus maenas to 4 weeks of ocean acidification [OA, P(CO 2 ) w  = 1800 µatm], at variable water bicarbonate levels, paralleled by changes in water pH. Cardiovascular performance was determined together with extra-(pH e ) and intracellular pH (pH i ), oxygen consumption, haemolymph CO 2 parameters, and ion composition. High water P(CO 2 ) caused haemolymph P(CO 2 ) to rise, but pH e and pH i remained constant due to increased haemolymph and cellular [HCO 3 - ]. This process was effective even under reduced seawater pH and bicarbonate concentrations. While extracellular cation concentrations increased throughout, anion levels remained constant or decreased. Despite similar levels of haemolymph pH and ion concentrations under OA, metabolic rates, and haemolymph flow were significantly depressed by 40 and 30%, respectively, when OA was combined with reduced seawater [HCO 3 - ] and pH. Our findings suggest an influence of water bicarbonate levels on metabolic rates as well as on correlations between blood flow and pH e . This previously unknown phenomenon should direct attention to pathways of acid-base regulation and their potential feedback on whole-animal energy demand, in relation with changing seawater carbonate parameters.

Fungal decay and shelf life of oranges coated with chitosan and bergamot, thyme, and tea tree essential oils.

PubMed

Cháfer, M; Sánchez-González, L; González-Martínez, Ch; Chiralt, A

2012-08-01

Chitosan coatings, containing or not essential oils (bergamot, thyme and tea tree oil), were applied to oranges (cv. Navel Powell). Antifungal effect was evaluated by applying coatings before and after inoculating the fruit with Penicillium italicum CECT 2294 (10(5) spores/mL), preventive and curative treatments, respectively. The effect of coatings on the quality parameters (acidity, pH, soluble solids, juice percentage, weight loss, firmness, color parameters, and respiration rate) was controlled for the different oranges samples throughout the cold storage time. Preventive antimicrobial treatments with coatings containing tea tree oil were the most effective with a reduction of the microbial growth (expressed as the percentage of infected samples) of 50%, as compared to the uncoated samples. The coatings did not lead to any relevant changes in the development of the sample quality parameters throughout the cold storage, except for a slightly reduced loss of both weight and firmness when the coatings contained bergamot oil. Results of this study are a useful tool for the development of new environmental friendly and healthier commercial applications in the control of the main postharvest fungal decay of citrus fruits. © 2012 Institute of Food Technologists®

Newly developed vaginal atrophy symptoms II and vaginal pH: a better correlation in vaginal atrophy?

PubMed

Tuntiviriyapun, P; Panyakhamlerd, K; Triratanachat, S; Chatsuwan, T; Chaikittisilpa, S; Jaisamrarn, U; Taechakraichana, N

2015-04-01

The primary objective of this study was to evaluate the correlation among symptoms, signs, and the number of lactobacilli in postmenopausal vaginal atrophy. The secondary objective was to develop a new parameter to improve the correlation. A cross-sectional descriptive study. Naturally postmenopausal women aged 45-70 years with at least one clinical symptom of vaginal atrophy of moderate to severe intensity were included in this study. All of the objective parameters (vaginal atrophy score, vaginal pH, the number of lactobacilli, vaginal maturation index, and vaginal maturation value) were evaluated and correlated with vaginal atrophy symptoms. A new parameter of vaginal atrophy, vaginal atrophy symptoms II, was developed and consists of the two most bothersome symptoms (vaginal dryness and dyspareunia). Vaginal atrophy symptoms II was analyzed for correlation with the objective parameters. A total of 132 naturally postmenopausal women were recruited for analysis. Vaginal pH was the only objective parameter found to have a weak correlation with vaginal atrophy symptoms (r = 0.273, p = 0.002). The newly developed vaginal atrophy symptoms II parameter showed moderate correlation with vaginal pH (r = 0.356, p < 0.001) and a weak correlation with the vaginal atrophy score (r = 0.230, p < 0.001). History of sexual intercourse within 3 months was associated with a better correlation between vaginal atrophy symptoms and the objective parameters. Vaginal pH was significantly correlated with vaginal atrophy symptoms. The newly developed vaginal atrophy symptoms II was associated with a better correlation. The vaginal atrophy symptoms II and vaginal pH may be better tools for clinical evaluation and future study of the vaginal ecosystem.

Optimization of crystallization conditions for biological macromolecules.

PubMed

McPherson, Alexander; Cudney, Bob

2014-11-01

For the successful X-ray structure determination of macromolecules, it is first necessary to identify, usually by matrix screening, conditions that yield some sort of crystals. Initial crystals are frequently microcrystals or clusters, and often have unfavorable morphologies or yield poor diffraction intensities. It is therefore generally necessary to improve upon these initial conditions in order to obtain better crystals of sufficient quality for X-ray data collection. Even when the initial samples are suitable, often marginally, refinement of conditions is recommended in order to obtain the highest quality crystals that can be grown. The quality of an X-ray structure determination is directly correlated with the size and the perfection of the crystalline samples; thus, refinement of conditions should always be a primary component of crystal growth. The improvement process is referred to as optimization, and it entails sequential, incremental changes in the chemical parameters that influence crystallization, such as pH, ionic strength and precipitant concentration, as well as physical parameters such as temperature, sample volume and overall methodology. It also includes the application of some unique procedures and approaches, and the addition of novel components such as detergents, ligands or other small molecules that may enhance nucleation or crystal development. Here, an attempt is made to provide guidance on how optimization might best be applied to crystal-growth problems, and what parameters and factors might most profitably be explored to accelerate and achieve success.

Optimization of crystallization conditions for biological macromolecules

PubMed Central

McPherson, Alexander; Cudney, Bob

2014-01-01

For the successful X-ray structure determination of macromolecules, it is first necessary to identify, usually by matrix screening, conditions that yield some sort of crystals. Initial crystals are frequently microcrystals or clusters, and often have unfavorable morphologies or yield poor diffraction intensities. It is therefore generally necessary to improve upon these initial conditions in order to obtain better crystals of sufficient quality for X-ray data collection. Even when the initial samples are suitable, often marginally, refinement of conditions is recommended in order to obtain the highest quality crystals that can be grown. The quality of an X-ray structure determination is directly correlated with the size and the perfection of the crystalline samples; thus, refinement of conditions should always be a primary component of crystal growth. The improvement process is referred to as optimization, and it entails sequential, incremental changes in the chemical parameters that influence crystallization, such as pH, ionic strength and precipitant concentration, as well as physical parameters such as temperature, sample volume and overall methodology. It also includes the application of some unique procedures and approaches, and the addition of novel components such as detergents, ligands or other small molecules that may enhance nucleation or crystal development. Here, an attempt is made to provide guidance on how optimization might best be applied to crystal-growth problems, and what parameters and factors might most profitably be explored to accelerate and achieve success. PMID:25372810

An evaluation of the relative quality of dike pools for benthic macroinvertebrates in the Lower Missouri River, USA

USGS Publications Warehouse

Poulton, B.C.; Allert, A.L.

2012-01-01

A habitat-based aquatic macroinvertebrate study was initiated in the Lower Missouri River to evaluate relative quality and biological condition of dike pool habitats. Water-quality and sediment-quality parameters and macroinvertebrate assemblage structure were measured from depositional substrates at 18 sites. Sediment porewater was analysed for ammonia, sulphide, pH and oxidation-reduction potential. Whole sediments were analysed for particle-size distribution, organic carbon and contaminants. Field water-quality parameters were measured at subsurface and at the sediment-water interface. Pool area adjacent and downstream from each dike was estimated from aerial photography. Macroinvertebrate biotic condition scores were determined by integrating the following indicator response metrics: % of Ephemeroptera (mayflies), % of Oligochaeta worms, Shannon Diversity Index and total taxa richness. Regression models were developed for predicting macroinvertebrate scores based on individual water-quality and sediment-quality variables and a water/sediment-quality score that integrated all variables. Macroinvertebrate scores generated significant determination coefficients with dike pool area (R2=0.56), oxidation–reduction potential (R2=0.81) and water/sediment-quality score (R2=0.71). Dissolved oxygen saturation, oxidation-reduction potential and total ammonia in sediment porewater were most important in explaining variation in macroinvertebrate scores. The best two-variable regression models included dike pool size + the water/sediment-quality score (R2=0.84) and dike pool size + oxidation-reduction potential (R2=0.93). Results indicate that dike pool size and chemistry of sediments and overlying water can be used to evaluate dike pool quality and identify environmental conditions necessary for optimizing diversity and productivity of important aquatic macroinvertebrates. A combination of these variables could be utilized for measuring the success of habitat enhancement activities currently being implemented in this system.

Orthorhombic lysozyme crystallization at acidic pH values driven by phosphate binding.

PubMed

Plaza-Garrido, Marina; Salinas-Garcia, M Carmen; Camara-Artigas, Ana

2018-05-01

The structure of orthorhombic lysozyme has been obtained at 298 K and pH 4.5 using sodium chloride as the precipitant and in the presence of sodium phosphate at a concentration as low as 5 mM. Crystals belonging to space group P2 1 2 1 2 1 (unit-cell parameters a = 30, b = 56, c = 73 Å, α = β = γ = 90.00°) diffracted to a resolution higher than 1 Å, and the high quality of these crystals permitted the identification of a phosphate ion bound to Arg14 and His15. The binding of this ion produces long-range conformational changes affecting the loop containing Ser60-Asn74. The negatively charged phosphate ion shields the electrostatic repulsion of the positively charged arginine and histidine residues, resulting in higher stability of the phosphate-bound lysozyme. Additionally, a low-humidity orthorhombic variant was obtained at pH 4.5, and comparison with those previously obtained at pH 6.5 and 9.5 shows a 1.5 Å displacement of the fifth α-helix towards the active-site cavity, which might be relevant to protein function. Since lysozyme is broadly used as a model protein in studies related to protein crystallization and amyloid formation, these results indicate that the interaction of some anions must be considered when analysing experiments performed at acidic pH values.

Influence of nutritional status, laboratory parameters and dietary patterns upon urinary acid excretion in calcium stone formers.

PubMed

Tessaro, Carolini Zanette Warmling; Ramos, Christiane Ishikawa; Heilberg, Ita Pfeferman

2018-04-26

Obesity and Metabolic Syndrome (MS) are associated with low urinary pH and represent risk factors for nephrolithiasis, especially composed by uric acid. Acidogenic diets may also contribute to a reduction of urinary pH. Propensity for calcium oxalate precipitation has been shown to be higher with increasing features of the MS. A retrospective evaluation of anthropometric and body composition parameters, MS criteria and the dietary patterns of overweight and obese calcium stone formers and their impact upon urinary pH and other lithogenic parameters was performed. Data regarding anthropometry, body composition, serum and urinary parameters and 3-days dietary records were obtained from medical records of 102(34M/68F) calcium stone formers. A negative correlation was found between urinary pH, waist circumference and serum uric acid levels (males). The endogenous production of organic acids (OA) was positively correlated with triglycerides levels and number of features of MS (males), and with glucose, uric acid and triglycerides serum levels, and number of features of MS (females). No significant correlations were detected between Net Acid Excretion (NAE) or Potential Renal Acid Load of the diet with any of the assessed parameters. A multivariate analysis showed a negative association between OA and urinary pH. The endogenous production of OA and not an acidogenic diet were found to be independently predictive factors for lower urinary pH levels in calcium stone formers. Hypercalciuric and/or hyperuricosuric patients presented higher OA levels and lower levels of urinary pH.

Evaluation of water quality and hydrogeochemistry of surface and groundwater, Tiruvallur District, Tamil Nadu, India

NASA Astrophysics Data System (ADS)

Krishna Kumar, S.; Hari Babu, S.; Eswar Rao, P.; Selvakumar, S.; Thivya, C.; Muralidharan, S.; Jeyabal, G.

2017-09-01

Water quality of Tiruvallur Taluk of Tiruvallur district, Tamil Nadu, India has been analysed to assess its suitability in relation to domestic and agricultural uses. Thirty water samples, including 8 surface water (S), 22 groundwater samples [15 shallow ground waters (SW) and 7 deep ground waters (DW)], were collected to assess the various physico-chemical parameters such as Temperature, pH, Electrical conductivity (EC), Total dissolved solids (TDS), cations (Ca, Mg, Na, K), anions (CO3, HCO3, Cl, SO4, NO3, PO4) and trace elements (Fe, Mn, Zn). Various irrigation water quality diagrams and parameters such as United states salinity laboratory (USSL), Wilcox, sodium absorption ratio (SAR), sodium percentage (Na %), Residual sodium carbonate (RSC), Residual Sodium Bicarbonate (RSBC) and Kelley's ratio revealed that most of the water samples are suitable for irrigation. Langelier Saturation Index (LSI) values suggest that the water is slightly corrosive and non-scale forming in nature. Gibbs plot suggests that the study area is dominated by evaporation and rock-water dominance process. Piper plot indicates the chemical composition of water, chiefly controlled by dissolution and mixing of irrigation return flow.

Biological activities and some physicochemical properties of sunflower honeys collected from the Thrace region of Turkey.

PubMed

Sari, Elif; Ayyildiz, Nusret

2012-12-01

Honey is a sweet food made by bees using nectar from flowers. Its quality depends on a number of factors, such as floral type, pH, moisture, free acidity, diastase activity, invert sugar and sucrose. The aim of the study is to examine the qualities of 50 sunflower honey (Helianthus annuus L.) collected from the Thrace region of Turkey, in terms of melissopalynological analysis, important chemical parameters and antioxidant activities . The total phenolic content of the honey samples was determined by the Folin-Ciocalteu method with spectrophotometry. The 1,2-diphenyl-2-picryl hydrazyl (DPPH) method was used to determine anti-radical activity and the phosphomolybdenum method was utilized for antioxidant activity. Correlations between the analysed parameters were found to be statistically significant (p < 0.05). The results obtained for physicochemical characteristics of sunflower honey indicate a good quality level, adequate processing, good maturity and freshness and that the sunflower honey samples studied proved to be good source of natural dietary antioxidants. This is the first report of the total phenolic content, antioxidant and antiradical activities of sunflower honeys collected from the Thrace region of Turkey.

Pork Quality Traits According to Postmortem pH and Temperature in Berkshire

PubMed Central

Kim, Tae Wan; Kim, Chul Wook; Yang, Mi Ra; No, Gun Ryoung; Kim, Il-Suk

2016-01-01

This study was performed to investigate the role of pH and temperature postmortem, and to demonstrate the importance of these factors in determining meat quality. Postmortem pH45min (pH at 45 min postmortem or initial pH) via analysis of Pearson’s correlation showed high positive correlation with pH change pHc24 (pH change from pH45min to pH24h postmortem). However, postmortem pH after 24 h (pH24h or ultimate pH) had a high negative correlation with pH change, pHc24, CIE L*, and protein content. Initial temperature postmortem (T1h ) was positively associated with a change in temperature from 45 min to 24 h postmortem (Tc24) and cooking loss, but negatively correlated with water holding capacity. Temperature at 24 h postmortem (T24h) was negatively associated with Tc24. Collectively, these results indicate that higher initial pH was associated with higher pHc24, T1h, and Tc24. However, higher initial pH was associated with a reduction in carcass weight, backfat thickness, CIE a* and b*, water holding capacity, collagen and fat content, drip loss, and cooking loss as well as decreased shear force. In contrast, CIE a* and b*, drip loss, cooking loss, and shear force in higher ultimate pH was showed by a similar pattern to higher initial pH, whereas pHc24, carcass weight, backfat thickness, water holding capacity, fat content, moisture content, protein content, T1h, T24h, and Tc24 were exhibited by completely differential patterns (p<0.05). Therefore, we suggest that initial pH, ultimate pH, and temperatures postmortem are important factors in determining the meat quality of pork. PMID:27499661

Quality Rankings of Ph.D.-Granting Departments of Geography, 1925-1980.

ERIC Educational Resources Information Center

Warf, Barney; Webster, David S.

All of the major academic quality rankings of American Ph.D.-granting geography departments during 1925-80 are examined, and trends in the universities and regions in which the best Ph.D.-granting geography departments have been located are analyzed. Seven major ratings of geography departments are considered. Reputational rankings were conducted…

A review of permissible limits of drinking water

PubMed Central

Kumar, Manoj; Puri, Avinash

2012-01-01

Water is one of the prime necessities of life. We can hardly live for a few days without water. In a man's body, 70-80% is water. Cell, blood, and bones contain 90%, 75%, and 22% water, respectively. The general survey reveals that the total surface area of earth is 51 crore km2 out of which 36.1 crore km2 is covered sea. In addition to this, we get water from rivers, lakes, tanks, and now on hills. In spite of such abundance, there is a shortage of soft water in the world. Physicochemical parameter of any water body plays a very important role in maintaining the fragile ecosystem that maintains various life forms. Present research paper deals with various water quality parameter, chlorides, dissolved oxygen, total iron, nitrate, water temperature, pH, total phosphorous, fecal coli form bacteria, and adverse effect of these parameters on human being. PMID:23112507

Secondary elements of blood pH variation can influence the effort effectiveness based on adaptive changes within a group of elite athletes.

PubMed

Martin, Ştefan Adrian; Tomescu, Valeriu; Voidăzan, Septimiu

2016-01-01

pH is the direct indicator of the body reaction following the activities performed. Establishing precise correlations between pH and blood biochemical parameters might support the balancing of values during periods of marked physical activity. We conducted a case study in a group of elite rowers. Twelve athletes were included in the study. Monitoring was carried out by collecting biological samples several times a day: in the morning, 80 minutes pre-workout, 12 hours after the last physical effort performed, at two different times, 10 days apart. Determinations were aimed at adapting the reported biochemical parameters depending on the effort performed. The following parameters were monitored: pH, HCO3, pCO2, pO2, BE, SBE, SBC, Ca++, Mg++, LDH, GPT, T-Pro, and Alb. The mean value of pH found in athletes was 7.41±0.024. The value obtained was significantly correlated to biochemical parameters such as BE (2.32±1.79), SBC (1.67±1.45), SBE (2.70±1.75). However, bicarbonate (HCO3) was statistically significantly related with SBE, SBC, SBE, and pO2, but did not present a strong association with the pH value (p=0.094). However, values such as Alb, Ca++, LDH, BE, SBC are related to pH value as a result of variations in the data submitted. The processed data evidence the fact that blood pH, in this case, is significantly influenced by a number of indices that correlate energy system activity, individual adaptation to effort, and the recovery process. The parameters under investigation (SBE, SBC, SBE, CPK, LDH) are associated with pH changes that could confirm the recovery efficiency of the athlete, along with a possible metabolic acidosis/alkalosis.

Effect of packaging technology on microbiological and sensory quality of a cooked blood sausage, Morcela de Arroz, from Monchique region of Portugal.

PubMed

Pereira, J A; Dionísio, L; Patarata, L; Matos, T J S

2015-03-01

Morcela de Arroz (MA), a popular Portuguese blood sausage, with high pH and water activity (aw), is traditionally commercialized without preservatives and unpacked. This study evaluated the best packaging solution to extend MA shelf life stored at 4±1°C for 44days: without packaging (WP), vacuum (VP) and modified atmosphere packaging (MAP) (80% CO2; 20% N2). Mesophilic (MTVC), psychrotrophic (PTVC), lactic acid bacteria (LAB), pseudomonads, molds and yeasts, Enterobacteriaceae, Listeria monocytogenes, Salmonella spp., Bacillus cereus, Clostridium perfringens, sensory properties, pH, moisture and aw were studied. Moisture and aw decreased (p<0.05) in WP. pH decreased in WP and MAP during storage. MTVC and PTVC counts increased to values around 7logCFU/g at 44days of storage. LAB and Enterobacteriaceae counts were higher (p<0.05) in VP. Pseudomonads were inhibited (p<0.05) by MAP after 8days of storage. Sensory parameters were affected (p<0.05) by packaging and storage time. Globally, MAP performed better. Copyright © 2014 Elsevier Ltd. All rights reserved.

Design of a Water Environment Monitoring System Based on Wireless Sensor Networks

PubMed Central

Jiang, Peng; Xia, Hongbo; He, Zhiye; Wang, Zheming

2009-01-01

A water environmental monitoring system based on a wireless sensor network is proposed. It consists of three parts: data monitoring nodes, data base station and remote monitoring center. This system is suitable for the complex and large-scale water environment monitoring, such as for reservoirs, lakes, rivers, swamps, and shallow or deep groundwaters. This paper is devoted to the explanation and illustration for our new water environment monitoring system design. The system had successfully accomplished the online auto-monitoring of the water temperature and pH value environment of an artificial lake. The system's measurement capacity ranges from 0 to 80 °C for water temperature, with an accuracy of ±0.5 °C; from 0 to 14 on pH value, with an accuracy of ±0.05 pH units. Sensors applicable to different water quality scenarios should be installed at the nodes to meet the monitoring demands for a variety of water environments and to obtain different parameters. The monitoring system thus promises broad applicability prospects. PMID:22454592

Spatial variability of groundwater quality of Sabour block, Bhagalpur district (Bihar, India)

NASA Astrophysics Data System (ADS)

Verma, D. K.; Bhunia, Gouri Sankar; Shit, Pravat Kumar; Kumar, S.; Mandal, Jajati; Padbhushan, Rajeev

2017-07-01

This paper examines the quality of groundwater of Sabour block, Bhagalpur district of Bihar state, which lies on the southern region of Indo-Gangetic plains in India. Fifty-nine samples from different sources of water in the block have been collected to determine its suitability for drinking and irrigational purposes. From the samples electrical conductivity (EC), pH and concentrations of Calcium (Ca2+), Magnesium (Mg2+), Sodium (Na+), Potassium (K+), carbonate ion (CO 3 2- ), Bicarbonate ion (HCO 3 - ), Chloride ion (Cl-), and Fluoride (F-) were determined. Surface maps of all the groundwater quality parameters have been prepared using radial basis function (RBF) method. RBF model was used to interpolate data points in a group of multi-dimensional space. Root Mean Square Error (RMSE) is employed to scrutinize the best fit of the model to compare the obtained value. The mean value of pH, EC, Ca2+, Mg2+, Na+, K+, HCO3 -, Cl-, and F- are found to be 7.26, 0.69, 38.98, 34.20, 16.92, 1.19, 0.02, and 0.28, respectively. Distribution of calcium concentration is increasing to the eastern part and K+ concentrations raise to the downstream area in the southwestern part. Low pH concentrations (less than 6.71) occur in eastern part of the block. Spatial variations of hardness in Sabour block portraying maximum concentration in the western part and maximum SAR (more than 4.23) were recorded in the southern part. These results are not exceeding for drinking and irrigation uses recommended by World Health Organization. Therefore, the majority of groundwater samples are found to be safe for drinking and irrigation management practices.

Developing a Water Quality Index (WQI) for an Irrigation Dam.

PubMed

De La Mora-Orozco, Celia; Flores-Lopez, Hugo; Rubio-Arias, Hector; Chavez-Duran, Alvaro; Ochoa-Rivero, Jesus

2017-04-29

Pollution levels have been increasing in water ecosystems worldwide. A water quality index (WQI) is an available tool to approximate the quality of water and facilitate the work of decision-makers by grouping and analyzing numerous parameters with a single numerical classification system. The objective of this study was to develop a WQI for a dam used for irrigation of about 5000 ha of agricultural land. The dam, La Vega, is located in Teuchitlan, Jalisco, Mexico. Seven sites were selected for water sampling and samples were collected in March, June, July, September, and December 2014 in an initial effort to develop a WQI for the dam. The WQI methodology, which was recommended by the Mexican National Water Commission (CNA), was used. The parameters employed to calculate the WQI were pH, electrical conductivity (EC), dissolved oxygen (DO), total dissolved solids (TDS), total hardness (TH), alkalinity (Alk), total phosphorous (TP), Cl - , NO₃, SO₄, Ca, Mg, K, B, As, Cu, and Zn. No significant differences in WQI values were found among the seven sampling sites along the dam. However, seasonal differences in WQI were noted. In March and June, water quality was categorized as poor. By July and September, water quality was classified as medium to good. Quality then decreased, and by December water quality was classified as medium to poor. In conclusion, water treatment must be applied before waters from La Vega dam reservoir can be used for irrigation or other purposes. It is recommended that the water quality at La Vega dam is continually monitored for several years in order to confirm the findings of this short-term study.

Sedimentation and Its Impacts/Effects on River System and Reservoir Water Quality: case Study of Mazowe Catchment, Zimbabwe

NASA Astrophysics Data System (ADS)

Tundu, Colleta; Tumbare, Michael James; Kileshye Onema, Jean-Marie

2018-04-01

Sediment delivery into water sources and bodies results in the reduction of water quantity and quality, increasing costs of water purification whilst reducing the available water for various other uses. The paper gives an analysis of sedimentation in one of Zimbabwe's seven rivers, the Mazowe Catchment, and its impact on water quality. The Revised Universal Soil Loss Equation (RUSLE) model was used to compute soil lost from the catchment as a result of soil erosion. The model was used in conjunction with GIS remotely sensed data and limited ground observations. The estimated annual soil loss in the catchment indicates soil loss ranging from 0 to 65 t ha yr-1. Bathymetric survey at Chimhanda Dam showed that the capacity of the dam had reduced by 39 % as a result of sedimentation and the annual sediment deposition into Chimhanda Dam was estimated to be 330 t with a specific yield of 226 t km-2 yr-1. Relationship between selected water quality parameters, TSS, DO, NO3, pH, TDS, turbidity and sediment yield for selected water sampling points and Chimhanda Dam was analyzed. It was established that there is a strong positive relationship between the sediment yield and the water quality parameters. Sediment yield showed high positive correlation with turbidity (0.63) and TDS (0.64). Water quality data from Chimhanda treatment plant water works revealed that the quality of water is deteriorating as a result of increase in sediment accumulation in the dam. The study concluded that sedimentation can affect the water quality of water sources.

Application of linear pH gradients for the modeling of ion exchange chromatography: Separation of monoclonal antibody monomer from aggregates.

PubMed

Kluters, Simon; Wittkopp, Felix; Jöhnck, Matthias; Frech, Christian

2016-02-01

The mobile phase pH is a key parameter of every ion exchange chromatography process. However, mechanistic insights into the pH influence on the ion exchange chromatography equilibrium are rare. This work describes a mechanistic model capturing salt and pH influence in ion exchange chromatography. The pH dependence of the characteristic protein charge and the equilibrium constant is introduced to the steric mass action model based on a protein net charge model considering the number of amino acids interacting with the stationary phase. This allows the description of the adsorption equilibrium of the chromatographed proteins as a function of pH. The model parameters were determined for a monoclonal antibody monomer, dimer, and a higher aggregated species based on a manageable set of pH gradient experiments. Without further modification of the model parameters the transfer to salt gradient elution at fixed pH is demonstrated. A lumped rate model was used to predict the separation of the monoclonal antibody monomer/aggregate mixture in pH gradient elution and for a pH step elution procedure-also at increased protein loadings up to 48 g/L packed resin. The presented model combines both salt and pH influence and may be useful for the development and deeper understanding of an ion exchange chromatography separation. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Efficacy of different washing solutions and contact times on the microbial quality and safety of fresh-cut paprika.

PubMed

Das, B Kumar; Kim, Ji Gang; Choi, Ji Weon

2011-10-01

The role of different washing solutions and contact times was investigated to determine their use as potential sanitizers for maintaining the microbial quality and food safety of fresh-cut paprika. Samples were cut into small pieces, washed for both 90 and 180 s by different washing solutions: tap water, chlorinated water (100 mg/L and pH 6.5-7), electrolyzed water (pH 7.2) and ozonized water (4 mg/L). Then, samples were packaged in 50 µm polypropylene bags and stored at 5 °C for 12 days, followed by an evaluation of the antimicrobial efficacy of the treatments. Various quality and safety parameters, such as gas composition, color, off-odor, electrical conductivity and microbial numbers, were evaluated during storage. Results revealed insignificant differences in gas composition, and no off-odor was observed in any of the samples during the storage period. However, longer contact time resulted in slightly lower hue angle value than a short one for all washing solutions. Moreover, samples washed with ozone washings showed lower electrolyte leakage than other washing solutions. Samples washed for longer contact time except those washed in ozonized water showed increased microbial numbers during storage. Hence, it has been concluded that longer contact time with ozone has positive effects, whereas the other washing solutions adversely affect the microbial quality and safety aspects of fresh-cut paprika.

Assessment of the quality of water for consumption by river-bank communities in areas exposed to urban and industrial pollutants in the municipalities of Abaetetuba and Barcarena in the state of Pará, Brazil.

PubMed

Medeiros, Adaelson Campelo; Lima, Marcelo de Oliveira; Guimarães, Raphael Mendonça

2016-03-01

In spite of the great technological advances in processes for treatment of water for human consumption, water actually used for supply has become a major public health challenge. This study assesses the quality of the water consumed in two riverside communities in the Brazilian state of Pará, in an area exposed to domestic and industrial pollutants. Four campaigns of sampling were carried out in the two communities. The variables used for the calculation of the water quality index - Índice de Qualidade da Água, or IQA - were: pH, total solids, chloride, fluoride, hardness and N-Nitrate. The waters used for human consumption in the Maranhão Community, where there is no contamination by industrial pollutants, presented adequate samples, with improvement in the dry season; on the other hand the waters of the Vila do Conde, a location close to the industrial activity, had quality that was unacceptable for human consumption in both the seasonal periods. The principal parameters affected were pH and N-Nitrate, with values up to 25 times the reference level of the Brazilian legislation for water for human consumption. These results indicated greater anthropic interference in the vicinity of Vila do Conde, in Barcarena. It is concluded that this population is in need of clinical assessments by specialized professionals on the state of its health.

Microbiological Characteristic and Nutrition Quality of Goat Milk Kefir Based on Vitamin D3 Fortification Time

NASA Astrophysics Data System (ADS)

Fauziyyah, F.; Panunggal, B.; Afifah, D. N.; Rustanti, N.; Anjani, G.

2018-02-01

Goat milk kefir fortified with vitamin D3 is expected to benefit individual with insulin resistance. Different vitamin D3 fortification time allegedly effect microbiological characteristic and nutrition quality of goat milk kefir due to its microbial growth curve, thus this study aimed to analyze those parameters. This study was an experimental research. This study contains five treatments (vitamin D3 fortification at 0, 6, 12, 18, or 24 hours of fermentation) and a group of control. Total lactic acid bacteria, vitamin D3, protein level, fat contain, crude fiber, viscosity, and pH was analyzed by Total Plate Count, spectrophotometry, Bradford method, Babcock method, gravimetric analysis, Ostwald method, and pH meter respectively. Time of vitamin D3 fortification significantly effect vitamin D3 content (p=0,021), fat content (p=0,001), crude fiber (p=0,0001), viscosity (p=0,010), and total lactic acid bacteria (p=0,048). The highest vitamin D3 content was found on the group fortified at 6 hours of fermentation. All treatment groups has lower fat content and crude fiber content than control group. Total LAB in all group meet the Codex standard (≥ 107 CFU/ml). Control group and fortification group at 24 hours of fermentation have higher viscosity than other groups. There was no significant difference found in goat milk kefir protein level (p=0,262) and pH (p=0,056) despite the difference of fortification time. Vitamin D3 fortification time effect vitamin D3 content, fat content, crude fiber, viscosity, and total lactic acid bacteria of goat milk kefir, but did not effect protein content and pH of goat milk kefir.

Effects of land use types on surface water quality across an anthropogenic disturbance gradient in the upper reach of the Hun River, Northeast China.

PubMed

Wang, Ruizhao; Xu, Tianle; Yu, Lizhong; Zhu, Jiaojun; Li, Xiaoyu

2013-05-01

Surface water quality is vulnerable to pollution due to human activities. The upper reach of the Hun River is an important water source that supplies 52 % of the storage capacity of the Dahuofang Reservoir, the largest reservoir for drinking water in Northeast China, which is suffering from various human-induced changes in land use, including deforestation, reclamation/farming, urbanization and mine exploitation. To investigate the impacts of land use types on surface water quality across an anthropogenic disturbance gradient at a local scale, 11 physicochemical parameters (pH, dissolved oxygen [DO], turbidity, oxygen redox potential, conductivity, biochemical oxygen demand [BOD5], chemical oxygen demand [COD], total nitrogen [TN], total phosphorus [TP], NO(3)(-)N, and NH(4)(+)-N) of water from 12 sampling sites along the upper reach of the Hun River were monitored monthly during 2009-2010. The sampling sites were classified into four groups (natural, near-natural, more disturbed, and seriously disturbed). The water quality exhibited distinct spatial and temporal characteristics; conductivity, TN, and NO(3)(-)-N were identified as key parameters indicating the water quality variance. The forest and farmland cover types played significant roles in determining the surface water quality during the low-flow, high-flow, and mean-flow periods based on the results of a stepwise linear regression. These results may provide incentive for the local government to consider sustainable land use practices for water conservation.

Physico-chemical analysis of ground water samples of coastal areas of south Chennai in the post-Tsunami scenario.

PubMed

Rajendran, A; Mansiya, C

2015-11-01

The study of changes in ground water quality on the east coast of chennai due to the December 26, 2004 tsunami and other subsequent disturbances is a matter of great concern. The post-Tsunami has caused considerable plant, animal, material and ecological changes in the entire stretch of chennai coastal area. Being very close to sea and frequently subjected to coastal erosion, water quality has been a concern in this coastal strip, and especially after the recent tsunami this strip seems to be more vulnerable. In the present investigation, ten ground water samples were collected from various parts of south chennai coastal area. Physico-chemical parameters such as pH, temperature, Biochemical oxygen demand (BOD), Dissolved oxygen (DO), total solids; turbidity and fecal coliform were analyzed. The overall Water quality index (WQI) values for all the samples were found to be in the range of 68.81-74.38 which reveals a fact that the quality of all the samples is only medium to good and could be used for drinking and other domestic uses only after proper treatment. The long term adverse impacts of tsunami on ground water quality of coastal areas and the relationships that exist and among various parameters are carefully analyzed. Local residents and corporation authorities have been made aware of the quality of their drinking water and the methods to conserve the water bodies. Copyright © 2015 Elsevier Inc. All rights reserved.

Atlantic salmon skin and fillet color changes effected by perimortem handling stress, rigor mortis, and ice storage.

PubMed

Erikson, U; Misimi, E

2008-03-01

The changes in skin and fillet color of anesthetized and exhausted Atlantic salmon were determined immediately after killing, during rigor mortis, and after ice storage for 7 d. Skin color (CIE L*, a*, b*, and related values) was determined by a Minolta Chroma Meter. Roche SalmoFan Lineal and Roche Color Card values were determined by a computer vision method and a sensory panel. Before color assessment, the stress levels of the 2 fish groups were characterized in terms of white muscle parameters (pH, rigor mortis, and core temperature). The results showed that perimortem handling stress initially significantly affected several color parameters of skin and fillets. Significant transient fillet color changes also occurred in the prerigor phase and during the development of rigor mortis. Our results suggested that fillet color was affected by postmortem glycolysis (pH drop, particularly in anesthetized fillets), then by onset and development of rigor mortis. The color change patterns during storage were different for the 2 groups of fish. The computer vision method was considered suitable for automated (online) quality control and grading of salmonid fillets according to color.

Application of least square support vector machine and multivariate adaptive regression spline models in long term prediction of river water pollution

NASA Astrophysics Data System (ADS)

Kisi, Ozgur; Parmar, Kulwinder Singh

2016-03-01

This study investigates the accuracy of least square support vector machine (LSSVM), multivariate adaptive regression splines (MARS) and M5 model tree (M5Tree) in modeling river water pollution. Various combinations of water quality parameters, Free Ammonia (AMM), Total Kjeldahl Nitrogen (TKN), Water Temperature (WT), Total Coliform (TC), Fecal Coliform (FC) and Potential of Hydrogen (pH) monitored at Nizamuddin, Delhi Yamuna River in India were used as inputs to the applied models. Results indicated that the LSSVM and MARS models had almost same accuracy and they performed better than the M5Tree model in modeling monthly chemical oxygen demand (COD). The average root mean square error (RMSE) of the LSSVM and M5Tree models was decreased by 1.47% and 19.1% using MARS model, respectively. Adding TC input to the models did not increase their accuracy in modeling COD while adding FC and pH inputs to the models generally decreased the accuracy. The overall results indicated that the MARS and LSSVM models could be successfully used in estimating monthly river water pollution level by using AMM, TKN and WT parameters as inputs.

[A study on the method of DNA extraction from unbuffered formalin-fixed and paraffin-embedded samples].

PubMed

Tian, Zi-Qiang; Liu, Jun-Feng; Zhang, Shao-Wei; Li, Bao-Qing; Wang, Fu-Shun; Zhang, Yue-Feng

2004-03-01

Unbuffered formalin is widely used to fix resected specimens in China. The DNA in unbuffered formalin-fixed and paraffin-embedded tissues is usually degraded seriously, so the extraction of DNA from these samples is difficult. This study was conducted to seek an optimal method to extract DNA from these samples. Fifteen blocks of esophageal carcinoma resected in Fourth Hospital of Hebei Medical University in 2000 were selected. The cells were lyzed by proteinase K digestion or heating under different pH values, then DNA was extracted by phenol:chloroform. After that, four parameters (deparaffined by xylene or histolene; digested for 48 h or 72 h at 37 degrees C or 56 degrees C; extracted by salting-out or phenol:chloroform) were optimized according to the principle of cross design. At last, the quality of obtained DNA was analyzed with electrophoresis and PCR amplification. The quality and quantity of DNA obtained by proteinase K digestion (the average yield is 17.88 microg) were better than that of heating under different pH (7-12)(P< 0.05). The quality and quantity of DNA digested at 56 degrees C were better than that at 37 degrees C, and similarly, digestion for 72 hours was better than that for 48 hours. The methods of deparaffin and extraction had no obvious influence on the quality and quantity of DNA. By means of NaCl salting-out after proteinase K digestion, more reliable quality of DNA can be obtained from unbuffered formalin-fixed and paraffin-embedded samples. Furthermore,digestion for three days at 56 degrees C is more likely to obtain DNA with high quality and quantity.

Soil quality index for evaluation of reclaimed coal mine spoil.

PubMed

Mukhopadhyay, S; Masto, R E; Yadav, A; George, J; Ram, L C; Shukla, S P

2016-01-15

Success in the remediation of mine spoil depends largely on the selection of appropriate tree species. The impacts of remediation on mine soil quality cannot be sufficiently assessed by individual soil properties. However, combination of soil properties into an integrated soil quality index provides a more holistic status of reclamation potentials of tree species. Remediation potentials of four tree species (Acacia auriculiformis, Cassia siamea, Dalbergia sissoo, and Leucaena leucocephala) were studied on reclaimed coal mine overburden dumps of Jharia coalfield, Dhanbad, India. Soil samples were collected under the canopies of the tree species. Comparative studies on the properties of soils in the reclaimed and the reference sites showed improvements in soil quality parameters of the reclaimed site: coarse fraction (-20.4%), bulk density (-12.8%), water holding capacity (+0.92%), pH (+25.4%), EC (+2.9%), cation exchange capacity (+46.6%), organic carbon (+91.5%), N (+60.6%), P (+113%), K (+19.9%), Ca (+49.6%), Mg (+12.2%), Na (+19.6%), S (+46.7%), total polycyclic aromatic hydrocarbons (-71.4%), dehydrogenase activity (+197%), and microbial biomass carbon (+115%). Principal component analysis (PCA) was used to identify key mine soil quality indicators to develop a soil quality index (SQI). Selected indicators include: coarse fraction, pH, EC, soil organic carbon, P, Ca, S, and dehydrogenase activity. The indicator values were converted into a unitless score (0-1.00) and integrated into SQI. The calculated SQI was significantly (P<0.001) correlated with tree biomass and canopy cover. Reclaimed site has 52-93% higher SQI compared to the reference site. Higher SQI values were obtained for sites reclaimed with D.sissoo (+93.1%) and C.siamea (+86.4%). Copyright © 2015 Elsevier B.V. All rights reserved.

Effects of feeding the herb Borreria latifolia on the meat quality of village chickens in Malaysia.

PubMed

Abbood, Ali A; Kassim, Azhar Bin; Jawad, Hasan S A; Manap, Yazid Abdul; Sazili, Awis Qurni

2017-06-01

An experiment was carried out to estimate the meat quality characteristics of village chickens (Gallus gallus) fed diets supplemented with dry leaves of Borreria latifolia (BL) used as a potential antioxidant source in chicken feed. In this study, 252 sexed 9-week-old village chickens with mean live body weight of 1,525.4 g for males and 1,254.1 g for females were divided into 7 groups (each group 18 birds) for each sex represented in 2 experiments. The first experiment was to evaluate the antioxidant activity of BL and the effect on meat quality through a comparison with Rosmarinus officinalis (RO); hence, 3 groups were conducted and included: T1 (control), basal diet without supplementation; T2, basal diet with 1% of BL; T3, basal diet with 1% of RO. T2 and T3 significantly affect pH value, lipid oxidation, cooking loss, and overall acceptability compared to T1, while no significant difference was observed between the dietary groups in respect of drip loss, color, tenderness, fatty acid profile, and meat composition. Furthermore, a significant effect of sex on lipid oxidation, pH, yellowness, and fatty acid profile was observed. There was no significant effect of sex on WHC, tenderness, lightness, redness, and sensory evaluation. A significant influence of postmortem aging period was detected on lipid oxidation, pH, tenderness, cooking loss, and redness. The obtained result in this study revealed a significance in the interaction of herb by sex in pH parameter and between herb and sex, herb by aging period, sex by aging period, and the herb by sex by aging period interactions with regard to lipid oxidation test. The second experiment was to estimate the effect of 3 different levels of BL on meat quality. Four groups were provided and involved: T1 (control), basal diet without supplementation; T2, basal diet with 1.5% of BL; T3, basal diet with 2% of BL; and T4, basal diet with 2.5% of BL. The result of this study showed a significant effect (P < 0.05) of the dietary groups on redness value, sensory evaluation, and lipid oxidation. A significant effect of sex on fatty acid profile and lipid oxidation was detected in addition a significant effect of postmortem aging period on redness, pH, tenderness, cooking loss, and lipid oxidation was noticed. There was no significance in the interaction between herb and sex through pH test while a significance in the interaction between herb and sex, herb  × aging period, sex × aging period, and herb × sex × aging period interactions with regard to lipid oxidation was found. It can be concluded that dietary supplementation of BL improved oxidative stability and enhanced meat quality. © 2017 Poultry Science Association Inc.

Long-term mesocosms study of the effects of ocean acidification on growth and physiology of the sea urchin Echinometra mathaei.

PubMed

Moulin, Laure; Grosjean, Philippe; Leblud, Julien; Batigny, Antoine; Collard, Marie; Dubois, Philippe

2015-02-01

Recent research on the impact of ocean acidification (OA) has highlighted that it is important to conduct long-term experiments including ecosystem interactions in order to better predict the possible effects of elevated pCO2. The goal of the present study was to assess the long-term impact of OA on a suite of physiological parameters of the sea urchin Echinometra mathaei in more realistic food conditions. A long-term experiment was conducted in mesocosms provided with an artificial reef in which the urchins principally fed on algae attached to the reef calcareous substrate. Contrasted pH conditions (pH 7.7 vs control) were established gradually over six months and then maintained for seven more months. Acid-base parameters of the coelomic fluid, growth and respiration rate were monitored throughout the experiment. Results indicate that E. mathaei should be able to regulate its extracellular pH at long-term, through bicarbonate compensation. We suggest that, within sea urchins species, the ability to accumulate bicarbonates is related to their phylogeny but also on the quantity and quality of available food. Growth, respiration rate and mechanical properties of the test were not affected. This ability to resist OA levels expected for 2100 at long-term could determine the future of coral reefs, particularly reefs where E. mathaei is the major bioeroder. Copyright © 2014 Elsevier Ltd. All rights reserved.

A linear and non-linear polynomial neural network modeling of dissolved oxygen content in surface water: Inter- and extrapolation performance with inputs' significance analysis.

PubMed

Šiljić Tomić, Aleksandra; Antanasijević, Davor; Ristić, Mirjana; Perić-Grujić, Aleksandra; Pocajt, Viktor

2018-01-01

Accurate prediction of water quality parameters (WQPs) is an important task in the management of water resources. Artificial neural networks (ANNs) are frequently applied for dissolved oxygen (DO) prediction, but often only their interpolation performance is checked. The aims of this research, beside interpolation, were the determination of extrapolation performance of ANN model, which was developed for the prediction of DO content in the Danube River, and the assessment of relationship between the significance of inputs and prediction error in the presence of values which were of out of the range of training. The applied ANN is a polynomial neural network (PNN) which performs embedded selection of most important inputs during learning, and provides a model in the form of linear and non-linear polynomial functions, which can then be used for a detailed analysis of the significance of inputs. Available dataset that contained 1912 monitoring records for 17 water quality parameters was split into a "regular" subset that contains normally distributed and low variability data, and an "extreme" subset that contains monitoring records with outlier values. The results revealed that the non-linear PNN model has good interpolation performance (R 2 =0.82), but it was not robust in extrapolation (R 2 =0.63). The analysis of extrapolation results has shown that the prediction errors are correlated with the significance of inputs. Namely, the out-of-training range values of the inputs with low importance do not affect significantly the PNN model performance, but their influence can be biased by the presence of multi-outlier monitoring records. Subsequently, linear PNN models were successfully applied to study the effect of water quality parameters on DO content. It was observed that DO level is mostly affected by temperature, pH, biological oxygen demand (BOD) and phosphorus concentration, while in extreme conditions the importance of alkalinity and bicarbonates rises over pH and BOD. Copyright © 2017 Elsevier B.V. All rights reserved.

Concentrations and annual fluxes for selected water-quality constituents from the USGS National Stream Quality Accounting Network (NASQAN) 1996-2000

USGS Publications Warehouse

Kelly, Valerie J.; Hooper, Richard P.; Aulenbach, Brent T.; Janet, Mary

2001-01-01

This report contains concentrations and annual mass fluxes (loadings) for a broad range of water-quality constituents measured during 1996-2000 as part of the U.S. Geological Survey National Stream Quality Accounting Network (NASQAN). During this period, NASQAN operated a network of 40-42 stations in four of the largest river basins of the USA: the Colorado, the Columbia, the Mississippi (including the Missouri and Ohio), and the Rio Grande. The report contains surface-water quality data, streamflow data, field measurements (e.g. water temperature and pH), sediment-chemistry data, and quality-assurance data; interpretive products include annual and average loads, regression parameters for models used to estimate loads, sub-basin yield maps, maps depicting percent detections for censored constituents, and diagrams depicting flow-weighted average concentrations. Where possible, a regression model relating concentration to discharge and season was used for flux estimation. The interpretive context provided by annual loads includes identifying source and sink areas for constituents and estimating the loadings to receiving waters, such as reservoirs or the ocean.

Second-harmonic generation and theoretical studies of protonation at the water/α-TiO 2 (1 1 0) interface

NASA Astrophysics Data System (ADS)

Fitts, Jeffrey P.; Machesky, Michael L.; Wesolowski, David J.; Shang, Xiaoming; Kubicki, James D.; Flynn, George W.; Heinz, Tony F.; Eisenthal, Kenneth B.

2005-08-01

The pH of zero net surface charge (pH pzc) of the α-TiO 2 (1 1 0) surface was characterized using second-harmonic generation (SHG) spectroscopy. The SHG response was monitored during a series of pH titrations conducted at three NaNO 3 concentrations. The measured pH pzc is compared with a pH pzc value calculated using the revised MUltiSIte Complexation (MUSIC) model of surface oxygen protonation. MUSIC model input parameters were independently derived from ab initio calculations of relaxed surface bond lengths for a hydrated surface. Model (pH pzc 4.76) and experiment (pH pzc 4.8 ± 0.3) agreement establishes the incorporation of independently derived structural parameters into predictive models of oxide surface reactivity.

Risk management and statistical multivariate analysis approach for design and optimization of satranidazole nanoparticles.

PubMed

Dhat, Shalaka; Pund, Swati; Kokare, Chandrakant; Sharma, Pankaj; Shrivastava, Birendra

2017-01-01

Rapidly evolving technical and regulatory landscapes of the pharmaceutical product development necessitates risk management with application of multivariate analysis using Process Analytical Technology (PAT) and Quality by Design (QbD). Poorly soluble, high dose drug, Satranidazole was optimally nanoprecipitated (SAT-NP) employing principles of Formulation by Design (FbD). The potential risk factors influencing the critical quality attributes (CQA) of SAT-NP were identified using Ishikawa diagram. Plackett-Burman screening design was adopted to screen the eight critical formulation and process parameters influencing the mean particle size, zeta potential and dissolution efficiency at 30min in pH7.4 dissolution medium. Pareto charts (individual and cumulative) revealed three most critical factors influencing CQA of SAT-NP viz. aqueous stabilizer (Polyvinyl alcohol), release modifier (Eudragit® S 100) and volume of aqueous phase. The levels of these three critical formulation attributes were optimized by FbD within established design space to minimize mean particle size, poly dispersity index, and maximize encapsulation efficiency of SAT-NP. Lenth's and Bayesian analysis along with mathematical modeling of results allowed identification and quantification of critical formulation attributes significantly active on the selected CQAs. The optimized SAT-NP exhibited mean particle size; 216nm, polydispersity index; 0.250, zeta potential; -3.75mV and encapsulation efficiency; 78.3%. The product was lyophilized using mannitol to form readily redispersible powder. X-ray diffraction analysis confirmed the conversion of crystalline SAT to amorphous form. In vitro release of SAT-NP in gradually pH changing media showed <20% release in pH1.2 and pH6.8 in 5h, while, complete release (>95%) in pH7.4 in next 3h, indicative of burst release after a lag time. This investigation demonstrated effective application of risk management and QbD tools in developing site-specific release SAT-NP by nanoprecipitation. Copyright © 2016 Elsevier B.V. All rights reserved.

A parametric comparative study of electrocoagulation and coagulation using ultrafine quartz suspensions.

PubMed

Kiliç, Mehtap Gülsün; Hoşten, Cetin; Demirci, Sahinde

2009-11-15

This paper attempts to compare electrocoagulation using aluminum anodes and stainless steel cathodes with conventional coagulation by aluminum sulfate dosing on aqueous suspensions of ultrafine quartz. Several key parameters affecting the efficiency of electrocoagulation and coagulation were investigated with laboratory scale experiments in search of optimal parameter values. Optimal values of the parameters were determined on the basis of the efficiency of turbidity removal from ultrafine quartz suspensions. The parameters investigated in the study were suspension pH, electrical potential, current density, electrocoagulation time, and aluminum dosage. A comparison between electrocoagulation and coagulation was made on the basis of total dissolved aluminum, revealing that electrocoagulation and coagulation were equally effective at the same aluminum dosage for the removal of quartz particles from suspensions. Coagulation, however, was more effective in a wider pH range (pH 6-9) than electrocoagulation which yielded optimum effectiveness in a relatively narrower pH range around 9, where, in both methods, these pH values corresponded to near-zero zeta potentials of quartz particles. Furthermore, experimental results confirmed that electrocoagulation could display some pH buffering capacity. The kinetics of electrocoagulation was very fast (<10 min) in approaching a residual turbidity, which could be modeled with a second-order rate equation.

The effects of season and sand mining activities on thermal regime and water quality in a large shallow tropical lake.

PubMed

Sharip, Zati; Zaki, Ahmad Taqiyuddin Ahmad

2014-08-01

Thermal structure and water quality in a large and shallow lake in Malaysia were studied between January 2012 and June 2013 in order to understand variations in relation to water level fluctuations and in-stream mining activities. Environmental variables, namely temperature, turbidity, dissolved oxygen, pH, electrical conductivity, chlorophyll-A and transparency, were measured using a multi-parameter probe and a Secchi disk. Measurements of environmental variables were performed at 0.1 m intervals from the surface to the bottom of the lake during the dry and wet seasons. High water level and strong solar radiation increased temperature stratification. River discharges during the wet season, and unsustainable sand mining activities led to an increased turbidity exceeding 100 NTU, and reduced transparency, which changed the temperature variation and subsequently altered the water quality pattern.

pH measurement and a rational and practical pH control strategy for high throughput cell culture system.

PubMed

Zhou, Haiying; Purdie, Jennifer; Wang, Tongtong; Ouyang, Anli

2010-01-01

The number of therapeutic proteins produced by cell culture in the pharmaceutical industry continues to increase. During the early stages of manufacturing process development, hundreds of clones and various cell culture conditions are evaluated to develop a robust process to identify and select cell lines with high productivity. It is highly desirable to establish a high throughput system to accelerate process development and reduce cost. Multiwell plates and shake flasks are widely used in the industry as the scale down model for large-scale bioreactors. However, one of the limitations of these two systems is the inability to measure and control pH in a high throughput manner. As pH is an important process parameter for cell culture, this could limit the applications of these scale down model vessels. An economical, rapid, and robust pH measurement method was developed at Eli Lilly and Company by employing SNARF-4F 5-(-and 6)-carboxylic acid. The method demonstrated the ability to measure the pH values of cell culture samples in a high throughput manner. Based upon the chemical equilibrium of CO(2), HCO(3)(-), and the buffer system, i.e., HEPES, we established a mathematical model to regulate pH in multiwell plates and shake flasks. The model calculates the required %CO(2) from the incubator and the amount of sodium bicarbonate to be added to adjust pH to a preset value. The model was validated by experimental data, and pH was accurately regulated by this method. The feasibility of studying the pH effect on cell culture in 96-well plates and shake flasks was also demonstrated in this study. This work shed light on mini-bioreactor scale down model construction and paved the way for cell culture process development to improve productivity or product quality using high throughput systems. Copyright 2009 American Institute of Chemical Engineers

HIF evaluation of In-Situ Aqua TROLL 400

USGS Publications Warehouse

Tillman, Evan F.

2017-10-18

The In-Situ Aqua TROLL 400 (Aqua TROLL 400) was tested at the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility (HIF) against known standards over the Aqua TROLL 400’s operating temperature to verify the manufacturer’s stated accuracy specifications and the USGS recommendations for pH, dissolved oxygen (DO), and specific conductance (SC). The Aqua TROLL 400 manufacturer’s specifications are within the USGS recommendations for all parameters tested, except for DO, which is outside the USGS recommendation at DO concentrations of 8.0 milligrams per liter (mg/L) and higher. The Aqua TROLL 400 was compliant with Serial Digital Interface at 1200 baud (SDI-12) version 1.3. During laboratory testing of pH, the Aqua TROLL 400 sonde met the U.S. Geological Survey “National Field Manual for the Collection of Water-Quality Data” (NFM) recommendations for pH at all values tested, except at 4 degrees Celsius (°C) at pH 9.395 and pH 3.998. The Aqua TROLL 400 met the manufacturer specifications for pH at all values tested, except for pH buffers 3.998, 9.395, and 10.245 at 4 °C; pH 2.990 and 3.998 at 15 °C; and pH 3.040 at 40 °C. The Aqua TROLL 400 met the NFM recommendations at 93.7 percent of the SC values tested and met the manufacturer’s accuracy specifications at 56.3 percent of the SC values tested. During the laboratory testing for DO, the Aqua TROLL 400 met the manufacturer specifications, except at 5.55 mg/L, and met the NFM recommendations at all concentrations tested. An Aqua TROLL 400 was field tested at USGS Station 02492620, National Space Technology Laboratories (NSTL) Station, Mississippi, on the Pearl River for 6 weeks and showed good agreement with the well-maintained site sonde data for pH, DO, temperature, and SC.

Day-to-day relations between stress and sleep and the mediating role of perseverative cognition.

PubMed

Van Laethem, Michelle; Beckers, Debby G J; van Hooff, Madelon L M; Dijksterhuis, Ap; Geurts, Sabine A E

2016-08-01

The goals of this longitudinal diary-based study were to shed light on the day-level relationship between stress and subsequent sleep, and to examine whether perseverative cognition is a mediating factor in this relation. A total of 44 Dutch PhD students were followed during a two-month period, from one month before their public thesis defense (ie, a stressful life event), until one month thereafter. Participants completed short evening and morning questionnaires on eight occasions (in anticipation of and following the defense), including questions about day-level stress, sleep quality, and perseverative cognition. Objective sleep parameters were collected with the SenseWear Pro Armband. Multilevel analysis was used to analyze daily observations nested within individuals. Analyses revealed that day-level stress was not directly related to subsequent subjective sleep indicators or to subsequent objective sleep indicators. Day-level stress was significantly associated with day-level perseverative cognition, and daily variations in perseverative cognition were significantly related to several day-level objective sleep parameters (sleep efficiency, marginally to number of awakenings, and wake after sleep onset), and to several day-level subjective sleep parameters (sleep quality, number of awakenings, wake after sleep onset). Finally, mediation analyses using path analysis suggested that, on the day level, perseverative cognition functions as a mediator between stress and several sleep parameters, namely, subjective sleep quality, objective sleep efficiency, and subjective wake after sleep onset. Perseverative cognition is a promising explanatory mechanism linking day-level stress to subjective and objective measures of sleep. Copyright © 2016 Elsevier B.V. All rights reserved.

Biodegradation of food waste using microbial cultures producing thermostable α-amylase and cellulase under different pH and temperature.

PubMed

Awasthi, Mukesh Kumar; Wong, Jonathan W C; Kumar, Sunil; Awasthi, Sanjeev Kumar; Wang, Quan; Wang, Meijing; Ren, Xiuna; Zhao, Junchao; Chen, Hongyu; Zhang, Zengqiang

2018-01-01

The aim of this work was to study the biodegradation of food waste employing thermostable α-amylase and cellulase enzymes producing bacteria. Four potential isolates were identified which were capable of producing maximum amylase and cellulase and belong to the amylolytic strains, Brevibacillus borstelensis and Bacillus licheniformis; cellulolytic strains, Bacillus thuringiensis and Bacillus licheniformis, respectively. These strains were selected based on its higher cell density, enzymatic activities and stability at a wide range of pH and temperature compared to other strains. The results indicated that 1:1 ratio of pre and post consumed food wastes (FWs) were helpful to facilitate the degradation employing bacterial consortium. In addition, organic matter decomposition and chemical parameters of the end product quality also indicated that bacterial consortium was very effective for 1:1 ratio of FWs degradation as compared to the other treatments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Anaerobic degradation of coconut husk leachate using UASB-reactor.

PubMed

Neena, C; Ambily, P S; Jisha, M S

2007-07-01

Reffing of coconut husk, the majorprocess in quality coir fibre extraction, causes serious pollution with brackish water lagoons of Kerala. An attempt is made to treat the coconut husk leachate by using a laboratory scale UASB-reactor The experiment was conducted with loading of leachate from 1 kg of fresh coconut husk. The anaerobic treatment was done continuously The parameters like VFA, pH, COD and polyphenols were analysed regularly during the evaluation of the reactor performance. The polyphenol, VFA and COD were diminished gradually with time. The pH of the reactor during the study was found to be in the range of 6-8. The biogas production was increased with loading and about 82% of the total COD/kg husk could be converted to biogas. The maximum polyphenol loading in the reactor was reached to about 298.51 mg/l of husk.

Water Quality Control for Shrimp Pond Using Adaptive Neuro Fuzzy Inference System : The First Project

NASA Astrophysics Data System (ADS)

Umam, F.; Budiarto, H.

2018-01-01

Shrimp farming becomes the main commodity of society in Madura Island East Java Indonesia. Because of Madura island has a very extreme weather, farmers have difficulty in keeping the balance of pond water. As a consequence of this condition, there are some farmers experienced losses. In this study an adaptive control system was developed using ANFIS method to control pH balance (7.5-8.5), Temperature (25-31°C), water level (70-120 cm) and Dissolved Oxygen (4-7,5 ppm). Each parameter (pH, temperature, level and DO) is controlled separately but can work together. The output of the control system is in the form of pump activation which provides the antidote to the imbalance that occurs in pond water. The system is built with two modes at once, which are automatic mode and manual mode. The manual control interface based on android which is easy to use.

Can we predict uranium bioavailability based on soil parameters? Part 1: effect of soil parameters on soil solution uranium concentration.

PubMed

Vandenhove, H; Van Hees, M; Wouters, K; Wannijn, J

2007-01-01

Present study aims to quantify the influence of soil parameters on soil solution uranium concentration for (238)U spiked soils. Eighteen soils collected under pasture were selected such that they covered a wide range for those parameters hypothesised as being potentially important in determining U sorption. Maximum soil solution uranium concentrations were observed at alkaline pH, high inorganic carbon content and low cation exchange capacity, organic matter content, clay content, amorphous Fe and phosphate levels. Except for the significant correlation between the solid-liquid distribution coefficients (K(d), L kg(-1)) and the organic matter content (R(2)=0.70) and amorphous Fe content (R(2)=0.63), there was no single soil parameter significantly explaining the soil solution uranium concentration (which varied 100-fold). Above pH=6, log(K(d)) was linearly related with pH [log(K(d))=-1.18 pH+10.8, R(2)=0.65]. Multiple linear regression analysis did result in improved predictions of the soil solution uranium concentration but the model was complex.

Stormwater quality from extensive green roofs in a subtropical region

NASA Astrophysics Data System (ADS)

Onis Pessoa, Jonas; Allasia, Daniel; Tassi, Rutineia; Vaz Viega, Juliana; Fensterseifer, Paula

2016-04-01

Green roofs have increasingly become an integral part of urban environments, mainly due to their aesthetic benefits, thermal comfort and efficiency in controlling excess runoff. However, the effects of this emerging technology in the qualitative characteristics of rainwater is still poorly understood. In this study was evaluated the effect of two different extensive green roofs (EGRs) and a traditional roof built with corrugated fiber cement sheets (control roof) in the quality of rainwater, in a subtropical climate area in the city of Santa Maria, in southern Brazil. The principal variant between the two EGRs were the type of plant species, time since construction, soil depth and the substrate characteristics. During the monitoring period of the experiment, between the months of April and December of 2015 fourteen rainfall events were selected for qualitative analysis of water from the three roofs and directly from rainfall. It was analyzed physical (turbidity, apparent color, true color, electrical conductivity, total solids, dissolved solids, suspended solids and temperature), chemical (pH, phosphate, total nitrogen, nitrate, nitrite, chloride, sulfate, BOD, iron and total hardness), heavy metals (copper, zinc, lead and chromium) and microbiological parameters (total coliforms and E. coli). It was also characterized the substrates used in both extensive green roofs. The results showed that the quality of the water drained from EGR s was directly influenced by their substrates (in turn containing significant levels of nutrients, organic matter and some metals). The passage of rainwater through green roofs and control roof resulted in the elevation of pH, allowing the conversion of the slightly acidic rainfall into basic water. Similarly, on both types of roofs occurred an increase of the values of most of the physical, chemical and microbiological parameters compared to rainwater. This same trend was observed for heavy metals, although with a much smaller degree. Thus, under the assessed conditions and time, the green roofs, in general, have not provided an improvement of water quality as indicated by some authors. However, it was found that some of the measured parameters showed a gradual improvement during the monitoring period. This suggests that the age of green roofs can affect efficiency in the qualitative control of water. In this regard, long-term research can contribute to a better understanding quality of stormwater runoff from green roofs, especially in regions such as Brazil, where the implementation of green roofs is incipient and in a phase of adaptation to the different environmental conditions of the country.

[Immobilization remediation of Cd and Pb contaminated soil: remediation potential and soil environmental quality].

PubMed

Sun, Yue-Bing; Wang, Peng-Chao; Xu, Ying-Ming; Sun, Yang; Qin, Xu; Zhao, Li-Jie; Wang, Lin; Liang, Xue-Feng

2014-12-01

A pot experiment was conducted to investigate the immobilization remediation effects of sepiolite on soils artificially combined contamination by Cd and Pb using a set of various pH and speciation of Cd and Pb in soil, heavy metal concentration in Oryza sativa L., and soil enzyme activity and microbial quantity. Results showed that the addition of sepiolite increased the soil pH, and the exchangeable fraction of heavy metals was converted into Fe-Mn oxide, organic and residual forms, the concentration of exchangeable form of Cd and Pb reduced by 1.4% - 72.9% and 11.8% - 51.4%, respectively, when compared with the control. The contents of heavy metals decreased with increasing sepiolite, with the maximal Cd reduction of 39.8%, 36.4%, 55.2% and 32.4%, respectively, and 22.1%, 54.6%, 43.5% and 17.8% for Pb, respectively, in the stems, leaves, brown rice and husk in contrast to CK. The addition of sepiolite could improve the soil environmental quality, the catalase and urease activities and the amount of bacteria and actinomycete were increased to some extents. Although the fungi number and invertase activity were inhibited compared with the control group, it was not significantly different (P > 0.05). The significant correlation between pH, available heavy metal content, urease and invertase activities and heavy metal concentration in the plants indicated that these parameters could be used to evaluate the effectiveness of stabilization remediation of heavy metal contaminated soil.

Spectral Rate Theory for Two-State Kinetics

NASA Astrophysics Data System (ADS)

Prinz, Jan-Hendrik; Chodera, John D.; Noé, Frank

2014-02-01

Classical rate theories often fail in cases where the observable(s) or order parameter(s) used is a poor reaction coordinate or the observed signal is deteriorated by noise, such that no clear separation between reactants and products is possible. Here, we present a general spectral two-state rate theory for ergodic dynamical systems in thermal equilibrium that explicitly takes into account how the system is observed. The theory allows the systematic estimation errors made by standard rate theories to be understood and quantified. We also elucidate the connection of spectral rate theory with the popular Markov state modeling approach for molecular simulation studies. An optimal rate estimator is formulated that gives robust and unbiased results even for poor reaction coordinates and can be applied to both computer simulations and single-molecule experiments. No definition of a dividing surface is required. Another result of the theory is a model-free definition of the reaction coordinate quality. The reaction coordinate quality can be bounded from below by the directly computable observation quality, thus providing a measure allowing the reaction coordinate quality to be optimized by tuning the experimental setup. Additionally, the respective partial probability distributions can be obtained for the reactant and product states along the observed order parameter, even when these strongly overlap. The effects of both filtering (averaging) and uncorrelated noise are also examined. The approach is demonstrated on numerical examples and experimental single-molecule force-probe data of the p5ab RNA hairpin and the apo-myoglobin protein at low pH, focusing here on the case of two-state kinetics.

[The Additional Role of Symptom-Reflux Association Analysis of Diagnosis of Gastroesophageal Reflux Disease Using Bravo Capsule pH Test].

PubMed

Jung, Kyoungwon; Park, Moo In; Park, Seun Ja; Moon, Won; Kim, Sung Eun; Kim, Jae Hyun

2017-10-25

Since the development of ambulatory esophageal pH monitoring test to diagnose gastroesophageal reflux disease (GERD), several parameters have been introduced. The aim of this study was to assess whether using the symptom index (SI), symptom sensitivity index (SSI), and symptom association probability (SAP), in addition to the DeMeester score (DS), would be useful for interpreting the Bravo pH monitoring test. A retrospective study, which included 68 patients with reflux symptoms refractory to proton pump inhibitor (PPI) therapy who underwent a Bravo capsule pH test between October 2006 and May 2015, was carried out. Acid reflux parameters and symptom reflux association parameters were analyzed. The median percent time of total pH<4 and DS were 2.90% (interquartile range [IQR] 1.13-6.03%) and 11.10 (IQR 4.90-22.80), respectively. According to the analysis of the day-to-day variation in percent time of total pH<4 (r=0.724) and DS (r=0.537), there was a significant correlation between Day 1 and Day 2. The positive rate of Bravo test according to DS was 27 (39.7%). Although thirty patients experienced symptoms during the test, there were no significant differences of reflux parameters compared with other patients. In the symptom group, 7 patients (23.3%) were identified as having negative DS and an abnormal symptom-related index. There were no significant test-related complications. In addition to the analysis of traditional acid parameters of the Bravo capsule pH test, diagnosis of GERD, including reflux hypersensitivity, can be improved by performing an analysis of the symptom-reflux association and of the day-to-day variation.

Development of class model based on blood biochemical parameters as a diagnostic tool of PSE meat.

PubMed

Qu, Daofeng; Zhou, Xu; Yang, Feng; Tian, Shiyi; Zhang, Xiaojun; Ma, Lin; Han, Jianzhong

2017-06-01

A fast, sensitive and effective method based on the blood biochemical parameters for the detection of PSE meat was developed in this study. A total of 200 pigs were slaughtered in the same slaughterhouse. Meat quality was evaluated by measuring pH, electrical conductivity and color at 45min, 2h and 24h after slaughtering in M. longissimus thoracis et lumborum (LD). Blood biochemical parameters were determined in blood samples collected during carcass bleeding. Principal component analysis (PCA) biplot showed that high levels of exsanguination Creatine Kinase, Lactate Dehydrogenase, Aspertate aminotransferase, blood glucose and lactate were associated with the PSE meat, and the five biochemical parameters were found to be good indicators of PSE meat Discriminant function analysis (DFA) was able to clearly identify PSE meat using the five biochemical parameters as input data, and the class model is an effective diagnostic tool in pigs which can be used to detect the PSE meat and reduce economic loss for the company. Copyright © 2017 Elsevier Ltd. All rights reserved.

Quality comparison of hydroponic tomatoes (Lycopersicon esculentum) ripened on and off vine

NASA Technical Reports Server (NTRS)

Arias, R.; Lee, T. C.; Specca, D.; Janes, H.

2000-01-01

There is a general belief that the quality of tomatoes ripened on vine is better than tomatoes ripened off the vine, influencing among other parameters, the price of this commodity. We compared the quality of hydroponic tomatoes ripened on and off vine by chemical, physical, and sensory evaluation to find what attributes are affected and to what extent. Lycopene, beta-carotene, total and soluble solids, moisture content, ascorbic acid, acidity, pH, texture, and color were analyzed. Tomatoes ripened on vine had significantly more lycopene, beta-carotene, soluble and total solids, higher a* and lower L*, and were firmer. However, a 100-judge panel rated only the color and overall liking of the vine-ripened tomatoes as more intense than the fruit ripened off vine. Therefore, the chemical and physical differences were mostly not large enough to influence the panelist's perception. The characterization of tomatoes ripened on and off vine may help to guide post-harvest handling and treatment and to improve the quality of tomatoes ripened off vine.

The relationship between exsanguination blood lactate concentration and carcass quality in slaughter pigs.

PubMed

Edwards, L N; Engle, T E; Correa, J A; Paradis, M A; Grandin, T; Anderson, D B

2010-07-01

A group of 128 cross-bred barrows were used to determine the relationship between exsanguination blood lactate concentration ([LAC]) and carcass quality following commercial marketing conditions. After 10h of feed withdrawal, pigs were loaded on a truck with a hydraulically lifted second deck and transported approximately 1h to the slaughter facility. Pigs were rested for 8h and stunned with carbon dioxide. Blood lactate concentration was measured on exsanguination blood. Fourteen pork quality measurements were obtained following normal post-mortem processing. Pearson correlations were used to determine the relationships between [LAC] and the meat quality parameters. Exsanguination blood lactate concentration ranged from 4 to 19.7 mM. Higher lactate was associated with lower 60 min pH (P=0.0004) and higher drip loss (P=0.02). These results suggest that under low-stress loading and standard marketing conditions, exsanguination [LAC] is predictive of the rate of early post-mortem metabolism. Copyright 2010 Elsevier Ltd. All rights reserved.

Effects on performance and meat quality of Holstein bulls fed high concentrate diets without implants following immunological castration.

PubMed

Marti, S; Jackson, J A; Slootmans, N; Lopez, E; Hodge, A; Pérez-Juan, M; Devant, M; Amatayakul-Chantler, S

2017-04-01

The objective of this study was to evaluate the effect of the GnRH vaccine on the performance and meat quality of Holstein bulls fed high concentrate diets. A total of 493 approximately 7month old bulls (initial BW 298±1.2kg) were allocated into 3 treatment groups, intact bulls (n=164), animals surgically castrated at 15 to 17d of the study (n=164), and animals vaccinated on 0 and 28d of the study with the GnRH vaccine (n=165). Animals were slaughtered between 131 and 133d and carcass quality was evaluated. Hot carcass weight, dressing percentage, fat classification and meat quality parameters did not differ significantly between surgically castrated and vaccinated animals but differed (P<0.05) from intact bulls. Carcass classification, pH at 26h, and fat color were not affected by treatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Guidelines and standard procedures for continuous water-quality monitors: Site selection, field operation, calibration, record computation, and reporting

USGS Publications Warehouse

Wagner, Richard J.; Mattraw, Harold C.; Ritz, George F.; Smith, Brett A.

2000-01-01

The U.S. Geological Survey uses continuous water-quality monitors to assess variations in the quality of the Nation's surface water. A common system configuration for data collection is the four-parameter water-quality monitoring system, which collects temperature, specific conductance, dissolved oxygen, and pH data, although systems can be configured to measure other properties such as turbidity or chlorophyll. The sensors that are used to measure these water properties require careful field observation, cleaning, and calibration procedures, as well as thorough procedures for the computation and publication of final records. Data from sensors can be used in conjunction with collected samples and chemical analyses to estimate chemical loads. This report provides guidelines for site-selection considerations, sensor test methods, field procedures, error correction, data computation, and review and publication processes. These procedures have evolved over the past three decades, and the process continues to evolve with newer technologies.

Exploring the Effects of Geographical Origin on the Chemical Composition and Quality Grading of Vitis vinifera L. cv. Chardonnay Grapes.

PubMed

Gambetta, Joanna M; Cozzolino, Daniel; Bastian, Susan E P; Jeffery, David W

2017-01-31

The relationship between berry chemical composition, region of origin and quality grade was investigated for Chardonnay grapes sourced from vineyards located in seven South Australian Geographical Indications (GI). Measurements of basic chemical parameters, amino acids, elements, and free and bound volatiles were conducted for grapes collected during 2015 and 2016. Multiple factor analysis (MFA) was used to determine the sets of data that best discriminated each GI and quality grade. Important components for the discrimination of grapes based on GI were 2-phenylethanol, benzyl alcohol and C6 compounds, as well as Cu, Zn, and Mg, titratable acidity (TA), total soluble solids (TSS), and pH. Discriminant analysis (DA) based on MFA results correctly classified 100% of the samples into GI in 2015 and 2016. Classification according to grade was achieved based on the results for elements such as Cu, Na, Fe, volatiles including C6 and aryl alcohols, hydrolytically-released volatiles such as (Z)-linalool oxide and vitispirane, pH, TSS, alanine and proline. Correct classification through DA according to grade was 100% for both vintages. Significant correlations were observed between climate, GI, grade, and berry composition. Climate influenced the synthesis of free and bound volatiles as well as amino acids, sugars, and acids, as a result of higher temperatures and precipitation.

[Physicochemical composition of bottled drinking water marketed in Ouagadougou (Burkina Faso)].

PubMed

Some, Issa Touridomon; Banao, Issouf; Gouado, Inocent; Tapsoba, Théophile Lincoln

2009-01-01

The bottled drinking water marketed in urban areas includes natural mineral water, spring water, and treated drinking water. Their physicochemical qualities depend on the type and quantity of their components and define their safe use. Bottled water is widely consumed in Ouagadougou (Burkina Faso), and many brand names exist. Although many publications have examined the microbiological qualities of such water, no study has examined the physicochemical quality of water from Burkina Faso. This study, conducted from March 2005 through January 2006, aimed to assess the physicochemical composition of drinking water sold in Ouagadougou to facilitate better choices and use by consumers. Results showed that all the water analyzed in Ouagadougou is soft (TH < 50 ppm) or moderately soft (50 < TH < 200 ppm) and weakly mineralized (total dissolved solid content < 500 mg/L, sulfates [SO(2-)(4)] < 200 mg/L, [Ca(++)] < 150 mg/L, [Mg(2+)] < 50 mg/L, and [HCO(3)-] < 600 mg/l). Some imported water, however, is hard and highly mineralized. French standards do not set limit values for the natural mineral water parameters described above, and much of the water sold in Ouagadougou was natural mineral water. The spring water met potability standards, except for the Montagne d'Arrée brand, which had a pH value of 5.8, below the WHO standards of 6.5 < pH 8.5.

Effects of road type during transport on lamb welfare and meat quality in dry hot climates.

PubMed

Miranda-de la Lama, Genaro C; Monge, Paula; Villarroel, Morris; Olleta, Jose Luis; García-Belenguer, Sylvia; María, Gustavo A

2011-06-01

This study determined whether transporting lambs on paved (PR) or unpaved roads (UR) for 3 h had an effect on plasma stress indicators (cortisol, lactate, glucose, creatine kinase [CK], red blood cells, white blood cells, hematocrit, and neutrophil/lymphocyte [N/L] ratio) and instrumental meat quality (pH24, bruising score, water holding capacity [WHC], color, and texture). A total of 48 Rasa Aragonesa male lambs were used that were approximately 100 days old (12.5 kg ± 1.64, carcass weight). The results suggest that transport on unpaved roads had a significant influence on physiological and hematological stress parameters. Road type had a significant effect on all variables, except for white and red blood cells, and hematocrit levels. The UR lambs had significantly higher (at least p ≤ 0.01) cortisol, lactate, glucose, and CK levels and a higher N/L ratio than PR lambs. Meat from UR lambs had some dark-cutting characteristics, with a darker color, higher ultimate pH, and higher tenderness values than PR. In conclusion, lambs transported on unpaved roads had a more intense stress response and poorer meat quality than lambs transported on paved roads. An effort to improve the logistics associated with route planning is necessary to prevent welfare problems during transport to slaughter.

PHOTOMETRIC ORBITS OF EXTRASOLAR PLANETS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Robert A.

We define and analyze the photometric orbit (PhO) of an extrasolar planet observed in reflected light. In our definition, the PhO is a Keplerian entity with six parameters: semimajor axis, eccentricity, mean anomaly at some particular time, argument of periastron, inclination angle, and effective radius, which is the square root of the geometric albedo times the planetary radius. Preliminarily, we assume a Lambertian phase function. We study in detail the case of short-period giant planets (SPGPs) and observational parameters relevant to the Kepler mission: 20 ppm photometry with normal errors, 6.5 hr cadence, and three-year duration. We define a relevantmore » 'planetary population of interest' in terms of probability distributions of the PhO parameters. We perform Monte Carlo experiments to estimate the ability to detect planets and to recover PhO parameters from light curves. We calibrate the completeness of a periodogram search technique, and find structure caused by degeneracy. We recover full orbital solutions from synthetic Kepler data sets and estimate the median errors in recovered PhO parameters. We treat in depth a case of a Jupiter body-double. For the stated assumptions, we find that Kepler should obtain orbital solutions for many of the 100-760 SPGP that Jenkins and Doyle estimate Kepler will discover. Because most or all of these discoveries will be followed up by ground-based radial velocity observations, the estimates of inclination angle from the PhO may enable the calculation of true companion masses: Kepler photometry may break the 'msin i' degeneracy. PhO observations may be difficult. There is uncertainty about how low the albedos of SPGPs actually are, about their phase functions, and about a possible noise floor due to systematic errors from instrumental and stellar sources. Nevertheless, simple detection of SPGPs in reflected light should be robust in the regime of Kepler photometry, and estimates of all six orbital parameters may be feasible in at least a subset of cases.« less

Adapting water treatment design and operations to the impacts of global climate change

NASA Astrophysics Data System (ADS)

Clark, Robert M.; Li, Zhiwei; Buchberger, Steven G.

2011-12-01

It is anticipated that global climate change will adversely impact source water quality in many areas of the United States and will therefore, potentially, impact the design and operation of current and future water treatment systems. The USEPA has initiated an effort called the Water Resources Adaptation Program (WRAP) which is intended to develop tools and techniques that can assess the impact of global climate change on urban drinking water and wastewater infrastructure. A three step approach for assessing climate change impacts on water treatment operation and design is being persude in this effort. The first step is the stochastic characterization of source water quality, the second step is the application of the USEPA Water Treatment Plant model and the third step is the application of cost algorithms to provide a metric that can be used to assess the coat impact of climate change. A model has been validated using data collected from Cincinnati's Richard Miller Water Treatment Plant for the USEPA Information Collection Rule (ICR) database. An analysis of the water treatment processes in response to assumed perturbations in raw water quality identified TOC, pH, and bromide as the three most important parameters affecting performance of the Miller WTP. The Miller Plant was simulated using the EPA WTP model to examine the impact of these parameters on selected regulated water quality parameters. Uncertainty in influent water quality was analyzed to estimate the risk of violating drinking water maximum contaminant levels (MCLs).Water quality changes in the Ohio River were projected for 2050 using Monte Carlo simulation and the WTP model was used to evaluate the effects of water quality changes on design and operation. Results indicate that the existing Miller WTP might not meet Safe Drinking Water Act MCL requirements for certain extreme future conditions. However, it was found that the risk of MCL violations under future conditions could be controlled by enhancing existing WTP design and operation or by process retrofitting and modification.

Effects of soil characteristics on grape juice nutrient concentrations and other grape quality parameters in Shiraz

NASA Astrophysics Data System (ADS)

Concepción Ramos, Maria; Romero, Maria Paz

2017-04-01

This study investigated the response of grapes to soil properties in the variety Shiraz (SH) cultivated in the Costers de Segre Designation of Origin (NE, Spain). The research was carried out in two areas with differences in vigor, which was examined using the Normalized Difference Vegetation Index (NDVI). Soil properties such as organic matter content, pH, electrical conductivity and nutrients (N, P, K, Ca, Mg, Cu, Zn and Mn) were analysed in the two areas. Soil analyses were limited to the upper 40 cm. Soil N-NO3 was measured in 2M KCl extracts. Assimilable phosphorus was analysed by extraction with 0.5 M NaHCO3 at pH 8.5 using the Olsen method. The available K, Ca and Mg were evaluated in hemaaxinecobalt trichloride extracts and the available fraction of Cu, Zn, Mn and Fe in DTPA- trietanolamine extracts, by spectroscopy atomic emission/absorption. Berry grapes were collected at maturity. Nutrients in grape juice (K, Ca, Mg Cu, Zn, Mn and Fe) were determined after a microwave hydrogen peroxide digestion in a closed vessel microwave digestion system and measured by spectroscopy. Other grape properties that determine grape quality such as pH, berry weight and sugar content were analysed using the methods proposed by the OIV. Differences in soil properties were observed between plots, which determined the differences in vigour. The vines with lower vigour were grown in the soils with higher pH, electrical conductivity and silt content, which had in addition higher Ca, Mg and K available levels as well as higher levels of Fe and Mn than the soil in which vines had higher vigour. However, the available fraction of Cu and Zn was smaller. Similar differences in nutrient concentration in the berry were observed for all nutrients except for Cu. Grape juice pH and total soluble solids (°Brix) were higher in the most vigorous vines. However, the differences in berry weight and total acidity at ripening were not significant. Keywords: acidity; berry weight; nutrients; pH; soil characteristics, sugar content.

Soil pH determines microbial diversity and composition in the park grass experiment.

PubMed

Zhalnina, Kateryna; Dias, Raquel; de Quadros, Patricia Dörr; Davis-Richardson, Austin; Camargo, Flavio A O; Clark, Ian M; McGrath, Steve P; Hirsch, Penny R; Triplett, Eric W

2015-02-01

The Park Grass experiment (PGE) in the UK has been ongoing since 1856. Its purpose is to study the response of biological communities to the long-term treatments and associated changes in soil parameters, particularly soil pH. In this study, soil samples were collected across pH gradient (pH 3.6-7) and a range of fertilizers (nitrogen as ammonium sulfate, nitrogen as sodium nitrate, phosphorous) to evaluate the effects nutrients have on soil parameters and microbial community structure. Illumina 16S ribosomal RNA (rRNA) amplicon sequencing was used to determine the relative abundances and diversity of bacterial and archaeal taxa. Relationships between treatments, measured soil parameters, and microbial communities were evaluated. Clostridium, Bacteroides, Bradyrhizobium, Mycobacterium, Ruminococcus, Paenibacillus, and Rhodoplanes were the most abundant genera found at the PGE. The main soil parameter that determined microbial composition, diversity, and biomass in the PGE soil was pH. The most probable mechanism of the pH impact on microbial community may include mediation of nutrient availability in the soil. Addition of nitrogen to the PGE plots as ammonium sulfate decreases soil pH through increased nitrification, which causes buildup of soil carbon, and hence increases C/N ratio. Plant species richness and plant productivity did not reveal significant relationships with microbial diversity; however, plant species richness was positively correlated with soil microbial biomass. Plants responded to the nitrogen treatments with an increase in productivity and a decrease in the species richness.

Dominancy of Trichodesmium sp. in the Biawak Island

NASA Astrophysics Data System (ADS)

Prihadi, D. J.

2018-03-01

The Biawak Island is one of the small islands in West Java Province with an abundance of marine biological resources. This research was conducted to collect the primary producer zooplankton and water quality parameters. Direct observation is done by field surveys and measurement in situ for plankton and environmental parameters such as temperature, water transparency, water current, salinity, dissolved oxygen, and pH. Trichodesmium sp. was found dominance in where some other types of zooplankton were found in the area, like Scenedesmus sp., Sagitta sp., Acartia sp. also occurred. Further, the most abundance of Trichodesmium sp. was found in southern of Biawak Island where mangroves, coral and seagrass ecosystem provide nutrients which indirectly support the abundance of planktons. Trichodesmium sp. is plankton that can survive in water with minimum nutrient.

Advanced multivariate data analysis to determine the root cause of trisulfide bond formation in a novel antibody–peptide fusion

PubMed Central

Goldrick, Stephen; Holmes, William; Bond, Nicholas J.; Lewis, Gareth; Kuiper, Marcel; Turner, Richard

2017-01-01

ABSTRACT Product quality heterogeneities, such as a trisulfide bond (TSB) formation, can be influenced by multiple interacting process parameters. Identifying their root cause is a major challenge in biopharmaceutical production. To address this issue, this paper describes the novel application of advanced multivariate data analysis (MVDA) techniques to identify the process parameters influencing TSB formation in a novel recombinant antibody–peptide fusion expressed in mammalian cell culture. The screening dataset was generated with a high‐throughput (HT) micro‐bioreactor system (AmbrTM 15) using a design of experiments (DoE) approach. The complex dataset was firstly analyzed through the development of a multiple linear regression model focusing solely on the DoE inputs and identified the temperature, pH and initial nutrient feed day as important process parameters influencing this quality attribute. To further scrutinize the dataset, a partial least squares model was subsequently built incorporating both on‐line and off‐line process parameters and enabled accurate predictions of the TSB concentration at harvest. Process parameters identified by the models to promote and suppress TSB formation were implemented on five 7 L bioreactors and the resultant TSB concentrations were comparable to the model predictions. This study demonstrates the ability of MVDA to enable predictions of the key performance drivers influencing TSB formation that are valid also upon scale‐up. Biotechnol. Bioeng. 2017;114: 2222–2234. © 2017 The Authors. Biotechnology and Bioengineering Published by Wiley Periodicals, Inc. PMID:28500668

Evaluation of the sustainability of contrasted pig farming systems: development of a market conformity tool for pork products based on technological quality traits.

PubMed

Gonzàlez, J; Gispert, M; Gil, M; Hviid, M; Dourmad, J Y; de Greef, K H; Zimmer, C; Fàbrega, E

2014-12-01

A market conformity tool, based on technological meat quality parameters, was developed within the Q-PorkChains project, to be included in a global sustainability evaluation of pig farming systems. The specific objective of the market conformity tool was to define a scoring system based on the suitability of meat to elaborate the main pork products, according to their market shares based on industry requirements, in different pig farming systems. The tool was based on carcass and meat quality parameters that are commonly used for the assessment of technological quality, which provide representative and repeatable data and are easily measurable. They were the following: cold carcass weight; lean meat percentage; minimum subcutaneous back fat depth at m. gluteus medius level, 45 postmortem and ultimate pH (measured at 24-h postmortem) in m. longissimus lumborum and semimembranosus; meat colour; drip losses and intramuscular fat content in a m. longissimus sample. Five categories of pork products produced at large scale in Europe were considered in the study: fresh meat, cooked products, dry products, specialties and other meat products. For each of the studied farming systems, the technological meat quality requirements, as well as the market shares for each product category within farming system, were obtained from the literature and personal communications from experts. The tool resulted in an overall conformity score that enabled to discriminate among systems according to the degree of matching of the achieved carcass and meat quality with the requirements of the targeted market. In order to improve feasibility, the tool was simplified by selecting ultimate pH at m. longissimus or semimembranosus, minimum fat thickness measured at the left half carcass over m. gluteus medius and intramuscular fat content in a m. longissimus sample as iceberg indicators. The overall suitability scores calculated by using both the complete and the reduced tools presented good correlation and the results obtained were similar. The tool could be considered as robust enough to discriminate among different systems, since it was tested in a wide range of them. It also can be used to detect improvement opportunities to enhance sustainability of pig farming systems. The final objective of the study was achieved, since the market suitability tool could be used in an integrated sustainability analysis of pig farming systems.

A new algorithm for design, operation and cost assessment of struvite (MgNH4PO4) precipitation processes.

PubMed

Birnhack, Liat; Nir, Oded; Telzhenski, Marina; Lahav, Ori

2015-01-01

Deliberate struvite (MgNH4PO4) precipitation from wastewater streams has been the topic of extensive research in the last two decades and is expected to gather worldwide momentum in the near future as a P-reuse technique. A wide range of operational alternatives has been reported for struvite precipitation, including the application of various Mg(II) sources, two pH elevation techniques and several Mg:P ratios and pH values. The choice of each operational parameter within the struvite precipitation process affects process efficiency, the overall cost and also the choice of other operational parameters. Thus, a comprehensive simulation program that takes all these parameters into account is essential for process design. This paper introduces a systematic decision-supporting tool which accepts a wide range of possible operational parameters, including unconventional Mg(II) sources (i.e. seawater and seawater nanofiltration brines). The study is supplied with a free-of-charge computerized tool (http://tx.technion.ac.il/~agrengn/agr/Struvite_Program.zip) which links two computer platforms (Python and PHREEQC) for executing thermodynamic calculations according to predefined kinetic considerations. The model can be (inter alia) used for optimizing the struvite-fluidized bed reactor process operation with respect to P removal efficiency, struvite purity and economic feasibility of the chosen alternative. The paper describes the algorithm and its underlying assumptions, and shows results (i.e. effluent water quality, cost breakdown and P removal efficiency) of several case studies consisting of typical wastewaters treated at various operational conditions.

Economic evaluation of exercise training in patients with pulmonary hypertension.

PubMed

Ehlken, Nicola; Verduyn, Cora; Tiede, Henning; Staehler, Gerd; Karger, Gabriele; Nechwatal, Robert; Opitz, Christian F; Klose, Hans; Wilkens, Heinrike; Rosenkranz, Stephan; Halank, Michael; Grünig, Ekkehard

2014-06-01

Exercise training as an add-on to medical therapy has been shown to improve exercise capacity, quality of life, and possibly prognosis in patients with pulmonary hypertension (PH). The purpose of this study was to analyze the impact of exercise training on healthcare costs in PH. Estimated healthcare costs have been compared between patients with severe PH under optimized medical therapy only (control group) versus patients who received exercise training as an add-on to medical therapy (training group). Cost-analysis included a cost-estimation model of costs for baseline and follow-up visits and all PH-related healthcare events that occurred within the follow-up period. Time to clinical worsening and survival were assessed by clinical records, phone, and/or control visits. At baseline, the training (n = 58) and control group (n = 48) did not differ in age, gender, WHO-functional class, 6-min walking distance, hemodynamic parameters, or PH-targeted medication. During a follow-up of 24 ± 12 months, the training group had significantly better survival rates at 1 and 3 years and less worsening events (death, lung transplantation, hospitalization due to PH, new PAH-targeted medication) than the control group (15 vs. 25 events, p < 0.05), which also led to lower estimated healthcare costs of 657 within a period of 2 years. This is the first study to investigate the cost-effectiveness of exercise training in PH. Due to less worsening events within 2 years, healthcare costs were lower in patients performing exercise training as add-on to medical therapy than in patients with medical treatment only. Further prospective, randomized studies are needed to confirm these findings.

Low-temperature solution processing of palladium/palladium oxide films and their pH sensing performance.

PubMed

Qin, Yiheng; Alam, Arif U; Pan, Si; Howlader, Matiar M R; Ghosh, Raja; Selvaganapathy, P Ravi; Wu, Yiliang; Deen, M Jamal

2016-01-01

Highly sensitive, easy-to-fabricate, and low-cost pH sensors with small dimensions are required to monitor human bodily fluids, drinking water quality and chemical/biological processes. In this study, a low-temperature, solution-based process is developed to prepare palladium/palladium oxide (Pd/PdO) thin films for pH sensing. A precursor solution for Pd is spin coated onto pre-cleaned glass substrates and annealed at low temperature to generate Pd and PdO. The percentages of PdO at the surface and in the bulk of the electrodes are correlated to their sensing performance, which was studied by using the X-ray photoelectron spectroscope. Large amounts of PdO introduced by prolonged annealing improve the electrode's sensitivity and long-term stability. Atomic force microscopy study showed that the low-temperature annealing results in a smooth electrode surface, which contributes to a fast response. Nano-voids at the electrode surfaces were observed by scanning electron microscope, indicating a reason for the long-term degradation of the pH sensitivity. Using the optimized annealing parameters of 200°C for 48 h, a linear pH response with sensitivity of 64.71±0.56 mV/pH is obtained for pH between 2 and 12. These electrodes show a response time shorter than 18 s, hysteresis less than 8 mV and stability over 60 days. High reproducibility in the sensing performance is achieved. This low-temperature solution-processed sensing electrode shows the potential for the development of pH sensing systems on flexible substrates over a large area at low cost without using vacuum equipment. Copyright © 2015 Elsevier B.V. All rights reserved.

Shelf life of cooked goat blood sausage prepared with the addition of heart and kidney.

PubMed

Silva, F A P; Amaral, D S; Guerra, I C D; Arcanjo, N M O; Bezerra, T K A; Ferreira, V C S; Araújo, I B S; Dalmás, P S; Madruga, M S

2014-08-01

This study focused on the effect of two packaging formats (vacuum packaging and over-wrap packaging) on the shelf life of cooked sausage prepared with blood, heart, kidney and goat meat fragments under storage at 4±1°C for a period of 90 days. The storage time and type of packaging significantly affected the chemical (pH, moisture, protein and TBARS number), physical (shear force) and microbial (mould and yeast) parameters of cooked sausage. Vacuum packaging maintained the microbiological and chemical qualities of cooked goat blood sausage for a longer period of time (63 days) compared to over-wrap packaging (41 days) and could be a viable alternative to refrigerated storage of the product for quality maintenance. Copyright © 2014 Elsevier Ltd. All rights reserved.

Application of Iron Oxide as a pH-dependent Indicator for Improving the Nutritional Quality

PubMed Central

2016-01-01

Acid food indicators can be used as pH indicators for evaluating the quality and freshness of fermented products during the full course of distribution. Iron oxide particles are hardly suspended in water, but partially or completely agglomerated. The agglomeration degree of the iron oxide particles depends on the pH. The pH-dependent particle agglomeration or dispersion can be useful for monitoring the acidity of food. The zeta potential of iron oxide showed a decreasing trend as the pH increased from 2 to 8, while the point of zero charge (PZC) was observed around at pH 6.0-7.0. These results suggested that the size of the iron oxide particles was affected by the change in pH levels. As a result, the particle sizes of iron oxide were smaller at lower pH than at neutral pH. In addition, agglomeration of the iron oxide particles increased as the pH increased from 2 to 7. In the time-dependent aggregation test, the average particle size was 730.4 nm and 1,340.3 nm at pH 2 and 7, respectively. These properties of iron oxide particles can be used to develop an ideal acid indicator for food pH and to monitor food quality, besides a colorant or nutrient for nutrition enhancement and sensory promotion in food industry. PMID:27482521

Single-Dose Electrospun Nanoparticles-in-Nanofibers Wound Dressings with Enhanced Epithelialization, Collagen Deposition, and Granulation Properties.

PubMed

Ali, Isra H; Khalil, Islam A; El-Sherbiny, Ibrahim M

2016-06-15

Phenytoin (Ph), an antiepileptic drug, was reported to exhibit high wound healing activity. However, its limited solubility, bioavailability, and inefficient distribution during topical administration limit its use. Therefore, this study aims to develop new single-dose electrospun nanoparticles-in-nanofibers (NPs-in-NFs) wound dressings that allow a well-controlled release of Ph. These NPs-in-NFs systems are based on enhanced chitosan (CS)/poly(ethylene oxide) (PEO) electrospun nanofibers (NFs) incorporating optimized Ph-loaded nanocarriers. First, a study was conducted to investigate Ph loading efficiency into polymeric nanocarriers of different types; pluronic nanomicelles and poly(lactic-co-glycolic) acids nanoparticles (PLGA NPs). The drug release profile from the nanocarriers was further optimized via lecithin coating. Second, different electrospinning parameters were manipulated to fabricate beads-free homogeneous NFs with optimized polymer ratios. Plain and Ph-loaded nanocarriers were characterized using Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic light scattering (DLS), and scanning electron microscopy (SEM). Both entrapment efficiency of Ph (EE%) and its release profile in phosphate buffer saline (PBS; pH 5.5), simulating the wound environment, were studied. Biodegradability, swelling, vapor permeability, and porosity of the developed Ph-loaded NPs-in-NFs wound dressings were investigated. Morphology of the NPs-in-NFs was also studied using SEM and confocal laser microscopy (CLSM). Besides, the release profiles of Ph from the optimized NPs-in-NFs were assessed. The newly developed wound dressings were evaluated in vitro for their cytotoxicity using human fibroblasts and in vivo using a wound healing mice model. Nanocarriers with particle size ranging from 100 to 180 nm were successfully prepared. All nanocarriers attained a high drug entrapment efficiency exceeding 94% and showed promising sustained release profiles compared to free Ph. Results also demonstrated that NFs incorporating the optimized lecithin-coated Ph-loaded PLGA NPs could be the most promising candidate for efficient wound healing. These NPs-in-NFs systems conferred a well-controlled and sustained release of Ph over 9 days. Moreover, they showed the best re-epithelization and healing quality during the in vivo study with minimal inflammatory and necrotic cells formation.

Application of Optical Imaging Techniques for Quantification of pH and O2 Dynamicsin Porous Media

NASA Astrophysics Data System (ADS)

Li, B.; Seliman, A. F.; Pales, A. R.; Liang, W.; Sams, A.; Darnault, C. J. G.; DeVol, T. A.

2016-12-01

Understanding the spatial and temporal distribution of physical and chemical parameters (e.g. pH, O2) is imperative to characterize the behavior of contaminants in a natural environment. The objectives of this research are to calibrate pH and O2 sensor foils, to develop a dual pH/O2 sensor foil, and to apply them into flow and transport experiments, in order to understand the physical and chemical parameters that control contaminant fate and transport in an unsaturated sandy porous medium. In addition, demonstration of a sensor foil that quantifies aqueous uranium concentration will be presented. Optical imaging techniques will be conducted with 2D tanks to investigate the influence of microbial exudates and plant roots on pH and O2 parameters and radionuclides transport. As a non-invasive method, the optical imaging technique utilizes optical chemical sensor films and either a digital camera or a spectrometer to capture the changes with high temporal and spatial resolutions. Sensor foils are made for different parameters by applying dyes to generate favorable fluorescence that is proportional to the parameter of interest. Preliminary results suggested that this method could detect pH ranging from 4.5 to 7.5. The result from uranium foil test with different concentrations in the range of 2 to 8 ppm indicated that a higher concentration of uranium resulted in a greater color intensity.

What Matters for Excellence in PhD Programs? Latent Constructs of Doctoral Program Quality Used by Early Career Social Scientists

ERIC Educational Resources Information Center

Morrison, Emory; Rudd, Elizabeth; Zumeta, William; Nerad, Maresi

2011-01-01

This paper unpacks how social science doctorate-holders come to evaluate overall excellence in their PhD training programs based on their domain-specific assessments of aspects of their programs. Latent class analysis reveals that social scientists 6-10 years beyond their PhD evaluate the quality of their doctoral program with one of two…

Water quality of the Garang River, Semarang, Central Java, Indonesia based on the government regulation standard

NASA Astrophysics Data System (ADS)

Ujianti, R. M. D.; Anggoro, S.; Bambang, A. N.; Purwanti, F.

2018-05-01

The Garang watershed composed by three main river streams has been managed by the Regional water company of the Semarang city, Central Java for drinking water supply. A river is often polluted by domestic waste and industrial effluents. Therefore water quality of the river should be keep to meet the Government regulation standard. The study aims to analyze water quality of the Garang’ river using pollution index based on the government regulation. Series data from 2010 to 2016 were derived from the Environmental and Forestry Office of the Central Java Province and sampling of water quality was taken in August 2017 from the middle of watershed area. Water quality parameters include temperature, pH, TDS, DO, COD, Phosphate, Nitrate, Chromium, Copper, Cadmium and H2S. The research indicates that concentration of Copper has exceeds the standard of the Government Regulation No. 82 Year 2001. The water pollution index is 1.23, its means that the river is lightly polluted. Therefore the river should be managed comprehensively for sustainable uses in order to create one river one management concept.

Establishing column batch repeatability according to Quality by Design (QbD) principles using modeling software.

PubMed

Rácz, Norbert; Kormány, Róbert; Fekete, Jenő; Molnár, Imre

2015-04-10

Column technology needs further improvement even today. To get information of batch-to-batch repeatability, intelligent modeling software was applied. Twelve columns from the same production process, but from different batches were compared in this work. In this paper, the retention parameters of these columns with real life sample solutes were studied. The following parameters were selected for measurements: gradient time, temperature and pH. Based on calculated results, batch-to-batch repeatability of BEH columns was evaluated. Two parallel measurements on two columns from the same batch were performed to obtain information about the quality of packing. Calculating the average of individual working points at the highest critical resolution (R(s,crit)) it was found that the robustness, calculated with a newly released robustness module, had a success rate >98% among the predicted 3(6) = 729 experiments for all 12 columns. With the help of retention modeling all substances could be separated independently from the batch and/or packing, using the same conditions, having high robustness of the experiments. Copyright © 2015 Elsevier B.V. All rights reserved.

Discrimination and characterization of strawberry juice based on electronic nose and tongue: comparison of different juice processing approaches by LDA, PLSR, RF, and SVM.

PubMed

Qiu, Shanshan; Wang, Jun; Gao, Liping

2014-07-09

An electronic nose (E-nose) and an electronic tongue (E-tongue) have been used to characterize five types of strawberry juices based on processing approaches (i.e., microwave pasteurization, steam blanching, high temperature short time pasteurization, frozen-thawed, and freshly squeezed). Juice quality parameters (vitamin C, pH, total soluble solid, total acid, and sugar/acid ratio) were detected by traditional measuring methods. Multivariate statistical methods (linear discriminant analysis (LDA) and partial least squares regression (PLSR)) and neural networks (Random Forest (RF) and Support Vector Machines) were employed to qualitative classification and quantitative regression. E-tongue system reached higher accuracy rates than E-nose did, and the simultaneous utilization did have an advantage in LDA classification and PLSR regression. According to cross-validation, RF has shown outstanding and indisputable performances in the qualitative and quantitative analysis. This work indicates that the simultaneous utilization of E-nose and E-tongue can discriminate processed fruit juices and predict quality parameters successfully for the beverage industry.

Effects of different fermentation parameters on quality characteristics of kefir.

PubMed

Kök-Taş, Tuğba; Seydim, Atif C; Ozer, Barbaros; Guzel-Seydim, Zeynep B

2013-02-01

The main objective of the study was to determine the effects of different fermentation parameters on kefir quality. Kefir samples were produced using kefir grains or natural kefir starter culture, and fermentation was carried out under normal or modified atmosphere (10% CO(2)) conditions. The microbiological (lactobacilli, lactococci, Lactobacillus acidophilus, Bifidobacterium spp., and yeasts), chemical (pH, lactic acid, total solids, protein, ethanol, exopolysaccharide contents), rheological, and sensory properties of kefir samples were investigated during a 21-d storage period. The use of different fermentation parameters or the choice of grain versus natural kefir starter culture did not significantly affect the content of microorganisms. Lactobacilli, lactococci, and yeast contents of kefir samples varied between 9.21 and 9.28, 9.23 and 9.29, and 4.71 and 5.53 log cfu/mL, respectively, on d 1 of storage. Contents of L. acidophilus and Bifidobacterium spp. were between 5.78 and 6.43 and between 3.19 and 6.14 log cfu/mL, respectively, during 21 d of storage. During the storage period, pH, lactic acid (%), total solids (%), protein (%), acetaldehyde, and ethanol contents of kefir samples ranged from 4.29 to 4.53, from 0.81 to 0.95%, from 7.81 to 8.21%, from 3.09 to 3.48%, from 3.8 to 23.6 mg/L, and from 76.5 to 5,147 mg/L, respectively. The exopolysaccharide contents of the samples decreased during 21 d of cold storage; the samples fermented under modified atmosphere had relatively higher exopolysaccharide contents, indicating higher potential therapeutic properties. The kefir samples exhibited non-Newtonian pseudoplastic flow behavior according to the power law model. According to the sensory results, kefir produced from natural kefir starter culture under CO(2) atmosphere had the highest overall evaluation score at d 1. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Developing a Water Quality Index (WQI) for an Irrigation Dam

PubMed Central

De La Mora-Orozco, Celia; Flores-Lopez, Hugo; Rubio-Arias, Hector; Chavez-Duran, Alvaro; Ochoa-Rivero, Jesus

2017-01-01

Pollution levels have been increasing in water ecosystems worldwide. A water quality index (WQI) is an available tool to approximate the quality of water and facilitate the work of decision-makers by grouping and analyzing numerous parameters with a single numerical classification system. The objective of this study was to develop a WQI for a dam used for irrigation of about 5000 ha of agricultural land. The dam, La Vega, is located in Teuchitlan, Jalisco, Mexico. Seven sites were selected for water sampling and samples were collected in March, June, July, September, and December 2014 in an initial effort to develop a WQI for the dam. The WQI methodology, which was recommended by the Mexican National Water Commission (CNA), was used. The parameters employed to calculate the WQI were pH, electrical conductivity (EC), dissolved oxygen (DO), total dissolved solids (TDS), total hardness (TH), alkalinity (Alk), total phosphorous (TP), Cl−, NO3, SO4, Ca, Mg, K, B, As, Cu, and Zn. No significant differences in WQI values were found among the seven sampling sites along the dam. However, seasonal differences in WQI were noted. In March and June, water quality was categorized as poor. By July and September, water quality was classified as medium to good. Quality then decreased, and by December water quality was classified as medium to poor. In conclusion, water treatment must be applied before waters from La Vega dam reservoir can be used for irrigation or other purposes. It is recommended that the water quality at La Vega dam is continually monitored for several years in order to confirm the findings of this short-term study. PMID:28468230

The Electro-Oxidation of Ethylene Glycol on Platinum over a Wide pH Range: Oscillations and Temperature Effects

PubMed Central

Sitta, Elton; Nagao, Raphael; Varela, Hamilton

2013-01-01

We report a comprehensive study of the electro-oxidation of ethylene glycol (EG) on platinum with emphasis on the effects exerted by the electrolyte pH, the EG concentration, and temperature, under both regular and oscillatory conditions. We extracted and discussed parameters such as voltammetric activity, reaction orders (with respect to [EG]), oscillation’s amplitude, frequency and waveform, and the evolution of the mean electrode potential at six pH values from 0 to 14. In addition, we obtained the apparent activation energies under several different conditions. Overall, we observed that increasing the electrolyte pH results in a discontinuous transition in most properties studied under both voltammetric and oscillatory regimes. As a relevant result in this direction, we found that the increase in the reaction order with pH is mediated by a minimum (~ 0) at pH = 12. Furthermore, the solution pH strongly affects all features investigated, c.f. the considerable increase in the oscillatory frequency and the decrease in the, oscillatory, activation energy as the pH increase. We suggest that adsorbed CO is probably the main surface-blocking species at low pH, and its absence at high pH is likely to be the main reason behind the differences observed. The size of the parameter region investigated and the amount of comparable parameters and properties presented in this study, as well as the discussion that followed illustrate the strategy of combining investigations under conventional and oscillatory regimes of electrocatalytic systems. PMID:24058650

An overall Water Quality Index (WQI) for a man-made aquatic reservoir in Mexico.

PubMed

Rubio-Arias, Hector; Contreras-Caraveo, Manuel; Quintana, Rey Manuel; Saucedo-Teran, Ruben Alfonso; Pinales-Munguia, Adan

2012-05-01

A Water Quality Index (WQI) is a useful statistical tool for simplifying, reporting and interpreting complex information obtained from any body of water. A simple number given by any WQI model explains the level of water contamination. The objective was to develop a WQI for the water of the Luis L. Leon dam located in the state of Chihuahua, Mexico. Monthly water samples were obtained in 2009; January 10, February 12, March 8, May 20, June 10, July 9, August 12, September 10, October 11, November 15 and December 13. Ten sampling sites were randomly selected after dividing the study area using a geographic package. In each site, two samples at the top depth of 0.20 m and 1.0 m were obtained to quantify physical-chemical parameters. The following 11 parameters were considered to calculate the WQI; pH, Electrical Conductivity (EC), Dissolved Oxygen (DO), color, turbidity, ammonia nitrogen, fluorides, chlorides, sulfates, Total Solids (TS) and phosphorous (P). The data analysis involved two steps; a single analysis for each parameter and the WQI calculation. The resulted WQI value classified the water quality according to the following ranges: <2.3 poor water; from 2.3 to 2.8 good water; and >2.8 excellent water. The results showed that the WQI values changed from low levels (WQI < 2.3) in some points during autumn time to high levels (WQI > 2.8) most of the year and the variation was due to time of sampling generally rainy season.

Comparison of Mann-Kendall and innovative trend method for water quality parameters of the Kizilirmak River, Turkey

NASA Astrophysics Data System (ADS)

Kisi, Ozgur; Ay, Murat

2014-05-01

Low, medium and high values of a parameter are very important issues in climatological, meteorological and hydrological events. Moreover these values are used to decide various design parameters based on scientific aspects and real applications everywhere in the world. With this concept, a new trend method recently proposed by Şen was used for water parameters, pH, T, EC, Na+, K+, CO3-2, HCO3-, Cl-, SO4-2, B+3 and Q recorded at five different stations (station numbers and locations: 1535-Sogutluhan (Sivas), 1501-Yamula (Kayseri), 1546-Tuzkoy (Kayseri), 1503-Yahsihan (Kirsehir), and 1533-Inozu (Samsun)) selected from the Kizilirmak River in Turkey. Low, medium and high values of the parameters were graphically evaluated with this method. For comparison purposes, the Mann-Kendall trend test was also applied to the same data. Differences of the two trend tests were also emphasised. It was found that the Şen trend test compared with the MK trend test had several advantages. The results also revealed that the Şen trend test could be successfully used for trend analysis of water parameters especially in terms of evaluation of low, medium and high values of data.

Activation of immunity, immune response, antioxidant ability, and resistance against Vibrio alginolyticus in white shrimp Litopenaeus vannamei decrease under long-term culture at low pH.

PubMed

Chen, Yu-Yuan; Chen, Jiann-Chu; Tseng, Kuei-Chi; Lin, Yong-Chin; Huang, Chien-Lun

2015-10-01

The growth, activation of immunity, immune parameters, and transcript levels of cytMnSOD, mtMnSOD, ecCuZnSOD, glutathione peroxidase (GPx), catalase, lysozyme, and penaeidin 3a were examined in white shrimp Litopenaeus vannamei reared at pH 6.8 and 8.1 after 24 weeks. No significant difference in growth was observed between the two groups. An in vitro study indicated that phenoloxidase activity and respiratory bursts (RB, release of the superoxide anion) were significantly higher in the haemocytes of pH 8.1 shrimp (shrimp reared at pH 8.1) than in pH 6.8 shrimp (shrimp reared at pH 6.8). An in vivo study indicated that the levels of immune parameters of pH 8.1 shrimp were significantly higher than in pH 6.8 shrimp, and the transcript levels of cytMnSOD, ecCuZnSOD, glutathione peroxidase, lysozyme, and penaeidin 3a were down-regulated in pH 6.8 shrimp. In another experiment, shrimp reared at pH 6.8 and 8.1 for 24 weeks were challenged with Vibrio alginolyticus. The mortality rate of pH 6.8 shrimp was significantly higher than in pH 8.1 shrimp over 12-168 h. Phagocytic activity, phagocytic index, and clearance efficiency to V. alginolyticus were significantly lower in pH 6.8 shrimp. We concluded that shrimp under long-term culture at pH 6.8 exhibited decreased resistance against V. alginolyticus as evidenced by reductions in the activation of immunity and immune parameters together with decreased transcript levels of cytMnSOD, ecCuZnSOD, GPx, lysozyme, and penaeidin 3a. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of pH on rheotaxis of bull sperm using microfluidics.

PubMed

El-Sherry, T M; Abdel-Ghani, M A; Abou-Khalil, N S; Elsayed, M; Abdelgawad, M

2017-10-01

The aim of the present research is to study the effect of pH values on the sperm rheotaxis properties. Semen collected from bulls was diluted with SOF medium (1:10). pH of the medium was adjusted using a digital pH meter to the following pH values: 6.0, 6.2, 6.4, 6.4, 6.8, 7.0. All kinetic parameters of sperm (n = 3,385) were determined through a computer-assisted sperm analysis (CASA) system using microfluidic devices with controlled flow velocity. The following parameters were determined: total motility (TM%), positive rheotaxis (PR%), straightline velocity (VSL, μm/s), average path velocity (VAP, μm/s), linearity (LIN, as VSL/VCL, %), beat cross-frequency (BCF, Hz) and curvilinear velocity (VCL, μm/s). Nitric oxide, calcium and potassium were estimated in semen at different pH values. To confirm the effect of nitric oxide and K + , we used sodium nitroprusside (an NO donor) and KCL as (a K + donor) to see their effect on sperm PR%. The results showed no difference in TM% at pH (6-7). The PR% was the lowest at pH 6 and 7. The best parameters for the PR% were at pH 6.4-6.6. The concentration of Ca +2 did not change at different pH values. The mean NO values decreased with the increase of pH; however, the mean values of K + increased with the increase of pH. Addition of high concentration of NO and K + to the semen media at fixed pH level had a negative effect on TM% and PR%. In conclusion, the bull sperm had the best rheotaxis properties at pH 6.4-6.6 and sensitive to the change of seminal NO and K + . © 2017 Blackwell Verlag GmbH.

Effect of freezing method and frozen storage duration on instrumental quality of lamb throughout display.

PubMed

Muela, E; Sañudo, C; Campo, M M; Medel, I; Beltrán, J A

2010-04-01

This study evaluated the effect of freezing method (FM) (air blast freezer, freezing tunnel, or nitrogen chamber) and frozen storage duration (FSD) (1, 3, or 6 months) on the instrumental measurements of quality of thawed lamb, aged for a total of 72 h, throughout a 10-d display period, compared to the quality of fresh meat. pH, colour, lipid oxidation, thawing, and cooking losses in Longissimus thoracis and lumborum muscle, were determined following standard methods. FM affected yellowness, FSD redness and thawing losses, and both affected oxidation (increased as freezing rate decreased and/or as storage duration increased). When compared with fresh meat, the main differences appeared on oxidation (where a significant interaction between treatment (3FM x 3FSD + fresh meat) with display duration was detected), and on total losses (thaw + cook losses). Oxidation was lower in fresh meat, but values were not significantly different from those stored frozen for 1 month. Fresh meat had smaller total losses than did thawed meat, but losses were not significantly different from meat frozen in the freezing tunnel and stored frozen for 1 month. Display duration had a greater effect on instrumental quality parameters than did FM or FSD. pH, b*, and oxidation increased, and L* and a* decreased with an increase in the number of days on display. In conclusion, neither freezing method nor frozen storage up to 6 months influenced extensively the properties of lamb when instrumental measurements of quality were measured in meat that had been displayed for 1d after thawing. The small deterioration shown in this study should not give consumers concerns about frozen meat. 2009 Elsevier Ltd. All rights reserved.

Analysis of problems with dry fermentation process for biogas production

NASA Astrophysics Data System (ADS)

Pilát, Peter; Patsch, Marek; Jandačka, Jozef

2012-04-01

The technology of dry anaerobic fermentation is still meeting with some scepticism, and therefore in most biogas plants are used wet fermentation technology. Fermentation process would be not complete without an optimal controlled condition: dry matter content, density, pH, and in particular the reaction temperature. If is distrust of dry fermentation eligible it was on the workplace of the Department of Power Engineering at University of Zilina built an experimental small-scale biogas station that allows analysis of optimal parameters of the dry anaerobic fermentation, in particular, however, affect the reaction temperature on yield and quality of biogas.

Water Quality and Trophic Status Study in Sembrong Reservoir during Monsoon Season

NASA Astrophysics Data System (ADS)

Hashim, S. I. N. S.; Talib, S. H. A.; Abustan, M. S.; Tajuddin, S. A. M.

2018-04-01

Sembrong is one of the reservoirs in Johor that supplies raw water to consumer for daily activities usage. Cleanliness and quality of water must be maintained to ensure that contamination is not applicable. This study is to determine the effects of sedimentation on water quality due to the deposition of sediment in the reservoir and to identify the rate of ammonia based on the location of the study area. There are several parameters required to obtain the data and reading for this study namely the temperature, dissolved oxygen, pH value, ammonia nitrogen and trophic status parameter that are consisting of Chlorophyll, total phosphorus and secchi depth. Seventeen (17) locations along Sembrong reservoir had been identified for sampling activities. From the result obtained, the reading of temperature and pH value has less significant differences between the locations involved. However, for dissolved oxygen, the highest readings were taken at location 6 and 7 which are 9.12 mg/L and 9.05 mg/L respectively compared to other location with the average reading of 8 mg/L. For ammonia nitrogen, the highest reading was at location 1 which is 2.24 mg/L, while the lowest reading at location 13 and 14 with 0.29 mg/L. Chlorophyll readings showed the highest reading of 92.33 μg/L at location 2 which is near to the inlet area while the lowest reading were taken at location 14 with 55.97 μg/L. For total phosphorus, location 1 has the highest reading of 19.50 μg/L compared to location 15 with 9.15 μg/L. The overall result indicates that the reading is high near the inlet and decreasing at the next location. So roughly, the river that connects to the Sembrong reservoir was carrying contaminants.

Lung disease severity in idiopathic pulmonary fibrosis is more strongly associated with impedance measures of bolus reflux than pH parameters of acid reflux alone.

PubMed

Gavini, S; Borges, L F; Finn, R T; Lo, W-K; Goldberg, H J; Burakoff, R; Feldman, N; Chan, W W

2017-05-01

Gastroesophageal reflux (GER) has been associated with idiopathic pulmonary fibrosis (IPF). Pathogenesis may be related to chronic micro-aspiration. We aimed to assess objective measures of GER on multichannel intraluminal impedance and pH study (MII-pH) and their relationship with pulmonary function testing (PFT) results, and to compare the performance of pH/acid reflux parameters vs corresponding MII/bolus parameters in predicting pulmonary dysfunction in IPF. This was a retrospective cohort study of IPF patients undergoing prelung transplant evaluation with MII-pH off acid suppression, and having received PFT within 3 months. Patients with prior fundoplication were excluded. Severe pulmonary dysfunction was defined using diffusion capacity of the lung for carbon monoxide (DLCO) ≤40%. Six pH/acid reflux parameters with corresponding MII/bolus reflux measures were specified a priori. Multivariate analyses were applied using forward stepwise logistic regression. Predictive value of each parameter for severe pulmonary dysfunction was calculated by area-under-the-receiver-operating-characteristic-curve or c-statistic. Forty-five subjects (67% M, age 59, 15 mild-moderate vs 30 severe) met criteria for inclusion. Patient demographics and clinical characteristics were similar between pulmonary dysfunction groups. Abnormal total reflux episodes and prolonged bolus clearance time were significantly associated with pulmonary dysfunction severity on univariate and multivariate analyses. No pH parameters were significant. The c-statistic of each pH parameter was lower than its MII counterpart in predicting pulmonary dysfunction. MII/bolus reflux, but not pH/acid reflux, was associated with pulmonary dysfunction in prelung transplant patients with IPF. MII-pH may be more valuable than pH testing alone in characterizing GER in IPF. © 2016 John Wiley & Sons Ltd.

Effect of highways and local activities on the quality of underground water in Ogun State, Nigeria: a case study of three districts in Ogun State, Nigeria.

PubMed

Odukoya, Olusegun O; Onianwa, Percy C; Sanusi, Olanrewaju I

2010-09-01

The effect of highways and local activities on the quality of groundwater in Ogun State, Nigeria was investigated. This was done by collecting groundwater samples from three different districts in the state, located in Southwestern Nigeria. The water samples collected at 5 m from the highway and control samples collected at 3 km from the highway were analyzed for the following physicochemical parameters: pH, conductivity, chemical oxygen demand, alkalinity, total hardness, total solid, suspended solid, dissolved solid, chloride, sulfate, phosphate, nitrate, phenol, and the metals-lead, zinc, iron, aluminum, sodium, and potassium. The levels of chromium, copper, and cadmium in the samples were below the detectable limit. The levels of the parameters show that there are significant differences between those in the samples and the controls (F test) except for phosphate and phenol. Also, anthropogenic sources (local activities) elevate the levels of different specific parameters, which are related to these activities. Good correlation was observed between traffic density and lead levels as well as between conductivity and dissolved solids. Comparisons with the World Health Organization guidelines indicate that most of the water samples are not suitable for human consumption.

Assessing the impact of preload on pyrite-rich sediment and groundwater quality.

PubMed

Karikari-Yeboah, Ohene; Addai-Mensah, Jonas

2017-02-01

Pyrite-rich sediments would, invariably, undergo redox reactions which would lead to acidic aqueous environment containing solubilized toxic metal species. When such sediments are subjected to preload, a technique employed by geotechnical engineers to improve the load-bearing capacity of highly compressible formation, transient flow of pore water, accompanied by acidity transfer, would occur as a response. Despite the concomitant environmental and socio-economic significance, to date, there has been limited interdisciplinary research on the underpinning geotechnical engineering and geo-environmental science issues for pyrite-rich sediments under preload. In this study, we investigate the effect of pyrite-rich sediment pore water transfer under preload surcharge on the receiving environment and the impact on the groundwater speciation and quality. Sediment samples were obtained at close depth intervals from boreholes established within pristine areas and those subjected to the preload application. Soil and pore water samples were subjected to solid/solution speciation, moisture contents, soil pH and the Atterberg Limits' analyses using standard analytical techniques and methods. Standpipes were also installed in the boreholes for groundwater sampling and in situ monitoring of water quality parameters. It is shown that the imposition of preload surcharge over pyritic sediment created a reducing environment rich in SO 4 2- , iron oxide minerals and organic matter. This reducing environment fostered organic carbon catabolism to generate excess pyrite and bicarbonate alkalinity, which would invariably impact adversely on soil quality and plant growth. These were accompanied by increase in pH, dissolved Al, Ca, Mg and K species beneath the surcharge.

Physicochemical and sensory evaluation of some cooking banana (Musa spp.) for boiling and frying process.

PubMed

Belayneh, M; Workneh, T S; Belew, D

2014-12-01

Experiments were conducted to study physicochemical properties of four cooking banana varieties (Cardaba, Nijiru, Matoke and Kitawira) and to determine their suitability for chips processing and boiling quality. A randomized complete block design with three replications was employed. Pulp to peel ratio, pulp firmness (before and after), total soluble solids, pH, titratable acidity, ascorbic acid, ease of peeling, pulp water absorption, duration of cooking (or boiling) and dry matter are the most important parameters to evaluate the quality of cooking banana including plantain. The different variety affected the fruit physical characteristics significantly (P ≤ 0.05). The Cardaba varieties fruit was found to be the heaviest and the longest. The Kitawira and Nijiru varieties had the smallest, shortest and thinnest fruit. The Cardaba contained 88 % more edible portions per unit fresh weight than the peel. The Nijiru, Matoke and Kitawira contained more pulp weight than peel weight. Most fruit chemical quality parameters were significantly (P ≤ 0.05) affected by the varieties. Similarly, the boiling and chips qualities were significantly (P ≤ 0.05) affected by varieties. Among others, the Cardaba variety was found to have high fruit weight, fruit length, fruit girth, fruit volume, total soluble solids, ascorbic acid, dry matter and low total titratable acidity. Thus, Cardaba provided the best quality boiled pulp which can serve for diversified culinary purposes. Generally, the Nijiru, Kitawira and Matoke varieties were found to be superior to produce acceptable quality chips. These varieties are recommended for chips development by food processors in Ethiopia.

An application of MC-SDSS for water supply management during a drought crisis.

PubMed

Jeihouni, Mehrdad; Toomanian, Ara; Alavipanah, Seyed Kazem; Shahabi, Mahmoud; Bazdar, Saba

2015-07-01

Climate change influences many countries' rainfall patterns and temperatures. In Iran, population growth has increased water demands. Tabriz is the capital of East Azerbaijan province, in northwestern Iran. A large proportion of the water required for this city is supplied from dams; thus, it is important to find alternatives to supply water for this city, which is the largest industrial city in northwestern Iran. In this paper, the groundwater quality was assessed using 70 wells in Tabriz Township. This work seeks to define the spatial distribution of groundwater quality parameters such as chloride, electrical conductivity (EC), pH, hardness, and sulfate using Geographic Information Systems (GIS) and geostatistics; map groundwater quality for drinking purposes employing multiple-criteria decision-making (MCDM), such as the Analytical Hierarchy Process (AHP) and fuzzy logic, in the study area; and develop an Spatial Decision Support System (SDSS) for managing a water crisis in the region. The map produced by the AHP is more accurate than the map produced using fuzzy logic because in the AHP, priorities were assigned to each parameter based on the weights given by water quality experts. The final map indicates that the groundwater quality increases from the north to the south and from the west to the east within the study area. During critical conditions, the groundwater quality maps and the presented SDSS core can be utilized by East Azerbaijan Regional Water Company to develop an SDSS to drill new wells or to select existing wells to supply drinking water to Tabriz City.

Assessment of water quality parameters using multivariate analysis for Klang River basin, Malaysia.

PubMed

Mohamed, Ibrahim; Othman, Faridah; Ibrahim, Adriana I N; Alaa-Eldin, M E; Yunus, Rossita M

2015-01-01

This case study uses several univariate and multivariate statistical techniques to evaluate and interpret a water quality data set obtained from the Klang River basin located within the state of Selangor and the Federal Territory of Kuala Lumpur, Malaysia. The river drains an area of 1,288 km(2), from the steep mountain rainforests of the main Central Range along Peninsular Malaysia to the river mouth in Port Klang, into the Straits of Malacca. Water quality was monitored at 20 stations, nine of which are situated along the main river and 11 along six tributaries. Data was collected from 1997 to 2007 for seven parameters used to evaluate the status of the water quality, namely dissolved oxygen, biochemical oxygen demand, chemical oxygen demand, suspended solids, ammoniacal nitrogen, pH, and temperature. The data were first investigated using descriptive statistical tools, followed by two practical multivariate analyses that reduced the data dimensions for better interpretation. The analyses employed were factor analysis and principal component analysis, which explain 60 and 81.6% of the total variation in the data, respectively. We found that the resulting latent variables from the factor analysis are interpretable and beneficial for describing the water quality in the Klang River. This study presents the usefulness of several statistical methods in evaluating and interpreting water quality data for the purpose of monitoring the effectiveness of water resource management. The results should provide more straightforward data interpretation as well as valuable insight for managers to conceive optimum action plans for controlling pollution in river water.

Evaluation of Xylem EXO water-quality sondes and sensors

USGS Publications Warehouse

Snazelle, Teri T.

2015-01-01

Two models of multiparameter sondes manufactured by Xylem, parent company of Yellow Springs Incorporated (YSI)—EXO1 and EXO2—equipped with EXO conductivity/temperature (C/T), pH, dissolved oxygen (DO), and turbidity sensors, were evaluated by the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility. The sondes and sensors were evaluated in two phases for compliance with the manufacturer’s specifications and the USGS acceptance criteria for continuous water-quality monitors. Phase one tested the accuracy of the water-quality sondes equipped: (a) with a C/T, pH, DO, and turbidity sensor by comparing the EXO sensors’ measured values to those of an equivalently configured YSI 6920 V2-2 sensor, and (b) with multiple sensors of the same parameter type (such as three pH sensors and a C/T sensor) on a single sonde at room temperature and at an extended temperature range. In addition to accuracy, the communication protocols and the manufacturing specifications for range of detection and operating temperature were also tested during this phase. Phase two evaluated the sondes’ performance in a surface-water environment by deploying an EXO1 and an EXO2 equipped with pH, C/T, DO, and turbidity sensors at USGS site 02492620 located at East Pearl River near Bay Saint Louis, Mississippi. The EXO sondes’ temperature deviations from a certified YSI 4600 digital thermometer were within the ±0.2 degree Celsius (°C) USGS criteria, but were greater than the ±0.01 °C manufacturing specification. The conductivity sensors met the ±3 percent USGS criteria for specific conductance greater than 100 microsiemens per centimeter. The sensors met the more stringent ±0.5 percent manufacturing specification only at room temperature in the 250 microsiemens per centimeter (µS/cm) standard. The manufacturing and USGS criteria (±0.2 pH unit) were met in pH standards 4, 9.2, 10, and 12.45, but were not met in pH 1.68 standard. The DO sensors met both the ±0.3 milligram per liter (mg/L) USGS criteria and the ±1 percent manufacturing specification. The ±5 percent USGS criteria for turbidity in waters not exceeding 2,000 formazin nephelometric units (FNU) were met by the five turbidity sensors tested; however, all five sensors failed to meet these requirements at turbidities exceeding 2,000 FNU. The more stringent ±2 percent manufacturing turbidity specification for water with less than 1,000 FNU was met by only one of the five sensors tested. The results from the field deployment indicated acceptable agreement in temperature, specific conductance, pH, and DO between the EXO sondes, the site sonde, and the reference sonde. The EXO1 and EXO2 turbidity measurements differed from the site sonde by approximately 23 and 25 percent, respectively.

Temporal assessment of copper speciation, bioavailability and toxicity in UK freshwaters using chemical equilibrium and biotic ligand models: Implications for compliance with copper environmental quality standards.

PubMed

Lathouri, Maria; Korre, Anna

2015-12-15

Although significant progress has been made in understanding how environmental factors modify the speciation, bioavailability and toxicity of metals such as copper in aquatic environments, the current methods used to establish water quality standards do not necessarily consider the different geological and geochemical characteristics of a given site and the factors that affect copper fate, bioavailability potential and toxicity. In addition, the temporal variation in the concentration and bioavailable metal fraction is also important in freshwater systems. The work presented in this paper illustrates the temporal and seasonal variability of a range of water quality parameters, and Cu speciation, bioavailability and toxicity at four freshwaters sites in the UK. Rivers Coquet, Cree, Lower Clyde and Eden (Kent) were selected to cover a broad range of different geochemical environments and site characteristics. The monitoring data used covered a period of around six years at almost monthly intervals. Chemical equilibrium modelling was used to study temporal variations in Cu speciation and was combined with acute toxicity modelling to assess Cu bioavailability for two aquatic species, Daphnia magna and Daphnia pulex. The estimated copper bioavailability, toxicity levels and the corresponding ecosystem risks were analysed in relation to key water quality parameters (alkalinity, pH and DOC). Although copper concentrations did not vary much during the sampling period or between the seasons at the different sites; copper bioavailability varied markedly. In addition, through the chronic-Cu BLM-based on the voluntary risk assessment approach, the potential environmental risk in terms of the chronic toxicity was assessed. A much higher likelihood of toxicity effects was found during the cold period at all sites. It is suggested that besides the metal (copper) concentration in the surface water environment, the variability and seasonality of other important water quality parameters should be considered in setting appropriately protective environmental quality standards for metals. Copyright © 2015 Elsevier B.V. All rights reserved.

Quality assessment of roof-harvested rainwater in the West Bank, Palestinian Authority.

PubMed

Daoud, A K; Swaileh, K M; Hussein, R M; Matani, M

2011-09-01

Rain harvesting is becoming more common in the Palestinian Territories as a result of drinking water scarcity. Although it might pose serious human health risk, this water is being consumed without treatment in many areas of the West Bank. The present study evaluates the physicochemical and microbial quality of harvested rainwater that is used as potable water in the West Bank. Samples from roof-harvested rainwater storage tanks (n = 42) were collected in summer (SS) 2006/winter (WS) 2007. Physicochemical parameters measured were: temperature, pH, electrical conductivity, salinity, total dissolved solids, turbidity, nitrate, copper and lead. With few exceptions, all these parameters were within WHO guideline values. All samples (100%) were found to contain coliforms and to be heavily contaminated with heterotrophic bacteria. About 67% of all samples were contaminated with fecal coliforms. Specific PCR technique confirmed the presence of five pathogenic microorganisms that can be ordered according to their prevalence as: Citrobacter (83%) > Acinetobacter (78%) > Aeromonas (52%) > Pseudomonas and Campylobacter (7%). Prevalence of microorganisms in SS was higher than in WS. Although the physicochemical quality of most harvested rainwater samples was in accordance with WHO guidelines for drinking water, stored rainwater was significantly contaminated with bacteria resulting in significant human health risk from infectious diseases.

Effect of high-pressure processing and thermal pasteurization on overall quality parameters of white grape juice.

PubMed

Chang, Yin-Hsuan; Wu, Sz-Jie; Chen, Bang-Yuan; Huang, Hsiao-Wen; Wang, Chung-Yi

2017-08-01

The aim of this study was to investigate the microbial levels, physicochemical and antioxidant properties and polyphenol oxidase (PPO) and peroxidase (POD) activities as well as to conduct a sensory analysis of white grape juice treated with high-pressure processing (HPP) and thermal pasteurization (TP), over a period of 20 days of refrigerated storage. HPP treatment of 600 MPa and TP significantly reduced aerobic bacteria, coliform and yeast/mold counts. At day 20 of storage, HPP-600 juice displayed no significant differences compared with fresh juice in terms of physicochemical properties such as titratable acidity, pH and soluble solids, and retained less than 50% PPO and POD activities. Although significant differences were observed in the color, antioxidant contents and antioxidant capacity of HPP-treated juice, the extent of these differences was substantially lower than that in TP-treated juice, indicating that HPP treatment can better retain the quality of grape juice. Sensory testing showed no significant difference between HPP-treated juice and fresh juice, while TP reduced the acceptance of grape juice. This study shows that HPP treatment maintained the overall quality parameters of white grape juice, thus effectively extending the shelf life during refrigerated storage. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Spatial variability of isoproturon mineralizing activity within an agricultural field: geostatistical analysis of simple physicochemical and microbiological soil parameters.

PubMed

El Sebai, T; Lagacherie, B; Soulas, G; Martin-Laurent, F

2007-02-01

We assessed the spatial variability of isoproturon mineralization in relation to that of physicochemical and biological parameters in fifty soil samples regularly collected along a sampling grid delimited across a 0.36 ha field plot (40 x 90 m). Only faint relationships were observed between isoproturon mineralization and the soil pH, microbial C biomass, and organic nitrogen. Considerable spatial variability was observed for six of the nine parameters tested (isoproturon mineralization rates, organic nitrogen, genetic structure of the microbial communities, soil pH, microbial biomass and equivalent humidity). The map of isoproturon mineralization rates distribution was similar to that of soil pH, microbial biomass, and organic nitrogen but different from those of structure of the microbial communities and equivalent humidity. Geostatistics revealed that the spatial heterogeneity in the rate of degradation of isoproturon corresponded to that of soil pH and microbial biomass.

Fluoride estimation and its correlation with other physicochemical parameters in drinking water of some areas of Balochistan, Pakistan.

PubMed

Chandio, Tasawar Ali; Khan, Muhammad Nasiruddin; Sarwar, Anila

2015-08-01

The fluoride level in drinking water is an important parameter and has to be controlled in order to prevent dental and skeletal fluorosis. The objective of this study is to assess fluoride content and other water quality parameters in the samples taken from open wells, tube wells, and karezes of Mastung, Mangochar, and Pringabad areas of Balochistan province. A total number of 96 drinking water samples out of 150 were found unfit for human consumption. Area-wise analysis show that the samples from 39 sites from Mastung, 12 from Mangochar, and 13 from Pringabad were found in the risk of dental fluorosis of mild to severe nature. However, 12 sampling sites from Mastung, 8 from Mangochar, and 2 from Pringabad were identified as the risks of mottling and skeletal fluorosis or other bone abnormalities. The highest concentration of F(-) has been observed as 14 mg L(-1) in Mastung. Correlation analysis show that fluoride solubility in drinking water is pH dependent; and the salts of Ca(2+), Na(+), K(+), Cl(-), and SO4(2-) contribute to attain the favorable pH for dissolution of fluoride compounds in drinking water. Principal component analysis shows that the geochemical composition of the rocks is only responsible for groundwater contamination. On the basis of the results, defloridation of the identified sampling sites and continuous monitoring of drinking water at regular basis is recommended at government level to avoid further fluorosis risks.

Multi-linear regression models predict the effects of water chemistry on acute lead toxicity to Ceriodaphnia dubia and Pimephales promelas.

PubMed

Esbaugh, A J; Brix, K V; Mager, E M; Grosell, M

2011-09-01

The current study examined the acute toxicity of lead (Pb) to Ceriodaphnia dubia and Pimephales promelas in a variety of natural waters. The natural waters were selected to range in pertinent water chemistry parameters such as calcium, pH, total CO(2) and dissolved organic carbon (DOC). Acute toxicity was determined for C. dubia and P. promelas using standard 48h and 96h protocols, respectively. For both organisms acute toxicity varied markedly according to water chemistry, with C. dubia LC50s ranging from 29 to 180μg/L and P. promelas LC50s ranging from 41 to 3598μg/L. Additionally, no Pb toxicity was observed for P. promelas in three alkaline natural waters. With respect to water chemistry parameters, DOC had the strongest protective impact for both organisms. A multi-linear regression (MLR) approach combining previous lab data and the current data was used to identify the relative importance of individual water chemistry components in predicting acute Pb toxicity for both species. As anticipated, the P. promelas best-fit MLR model combined DOC, calcium and pH. Unexpectedly, in the C. dubiaMLR model the importance of pH, TCO(2) and calcium was minimal while DOC and ionic strength were the controlling water quality variables. Adjusted R(2) values of 0.82 and 0.64 for the P. promelas and C. dubia models, respectively, are comparable to previously developed biotic ligand models for other metals. Copyright © 2011 Elsevier Inc. All rights reserved.

Optimization of supercritical carbon dioxide treatment for the inactivation of the natural microbial flora in cubed cooked ham.

PubMed

Ferrentino, Giovanna; Balzan, Sara; Spilimbergo, Sara

2013-02-15

This study aims to investigate the effects of supercritical carbon dioxide (SC-CO₂) treatment on the inactivation of the natural microbial flora in cubed cooked ham. Response surface methodology with a central composite design was applied to determine the optimal process conditions and investigate the effect of three independent variables (pressure, temperature and treatment time). Additionally, analyses of texture, pH and color together with a storage study of the product were performed to determine its microbial and qualitative stability. Response surface analysis revealed that 12 MPa, 50 °C, 5 min were the optimal conditions to obtain about 3.0, 1.6, and 2.5 Log(CFU/g) reductions of mesophilic aerobic bacteria, psychrophilic bacteria and lactic acid bacteria respectively. Inactivation to undetectable levels of yeasts and molds and coliforms was also obtained. A storage study of 30 days at 4 °C was carried out on the treated product (12 MPa, 50 °C, 5 min) monitoring microbial growth, pH, texture, and color parameters (L*, a*, b* and ΔE). Microbial loads slightly increased and after 30 days of storage reached the same levels detected in the fresh product. Color parameters (L*, a*, b*) showed slight variations while pH and texture did not change significantly. On the basis of the results obtained, SC-CO₂ can be considered a promising technique to microbiologically stabilize cubed cooked ham and, in general, cut/sliced meat products without affecting its quality attributes. Copyright © 2012 Elsevier B.V. All rights reserved.

Development of a colorimetric microfluidic pH sensor for autonomous seawater measurements.

PubMed

Rérolle, Victoire M C; Floquet, Cedric F A; Harris, Andy J K; Mowlem, Matt C; Bellerby, Richard R G J; Achterberg, Eric P

2013-07-05

High quality carbonate chemistry measurements are required in order to fully understand the dynamics of the oceanic carbonate system. Seawater pH data with good spatial and temporal coverage are particularly critical to apprehend ocean acidification phenomena and their consequences. There is a growing need for autonomous in situ instruments that measure pH on remote platforms. Our aim is to develop an accurate and precise autonomous in situ pH sensor for long term deployment on remote platforms. The widely used spectrophotometric pH technique is capable of the required high-quality measurements. We report a key step towards the miniaturization of a colorimetric pH sensor with the successful implementation of a simple microfluidic design with low reagent consumption. The system is particularly adapted to shipboard deployment: high quality data was obtained over a period of more than a month during a shipboard deployment in northwest European shelf waters, and less than 30 mL of indicator was consumed. The system featured a short term precision of 0.001 pH (n=20) and an accuracy within the range of a certified Tris buffer (0.004 pH). The quality of the pH system measurements have been checked using various approaches: measurements of certified Tris buffer, measurement of certified seawater for DIC and TA, comparison of measured pH against calculated pH from pCO2, DIC and TA during the cruise in northwest European shelf waters. All showed that our measurements were of high quality. The measurements were made close to in situ temperature (+0.2°C) in a sampling chamber which had a continuous flow of the ship's underway seawater supply. The optical set up was robust and relatively small due to the use of an USB mini-spectrometer, a custom made polymeric flow cell and an LED light source. The use of a three wavelength LED with detection that integrated power across the whole of each LED output spectrum indicated that low wavelength resolution detectors can be used instead of the current USB mini spectrophotometer. Artefacts due to the polychromatic light source and inhomogeneity in the absorption cell are shown to have a negligible impact on the data quality. The next step in the miniaturization of the sensor will be the incorporation of a photodiode as detector to replace the spectrophotometer. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Leaching of lead from new unplasticized polyvinyl chloride (uPVC) pipes into drinking water.

PubMed

Zhang, Yuanyuan; Lin, Yi-Pin

2015-06-01

Unplasticized polyvinyl chloride (uPVC) pipes have been used in the premise plumbing system due to their high strength, long-term durability, and low cost. uPVC pipes, however, may contain lead due to the use of lead compounds as the stabilizer during the manufacturing process. The release of lead from three locally purchased uPVC pipes was investigated in this study. The effects of various water quality parameters including pH value, temperature, and type of disinfectant on the rate of lead release were examined. The elemental mapping obtained using scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX) confirmed the presence of lead on the inner surfaces of the uPVC pipes and their surface lead weight percentages were determined. The leachable lead concentration for each pipe was determined using high strength acidic EDTA solutions (pH 4, EDTA = 100 mg/L). Lead leaching experiments using tap water and reconstituted tape water under static conditions showed that the rate of lead release increased with the decreasing pH value and increasing temperature. In the presence of monochloramine, lead release was faster than that in the presence of free chlorine.

Rapid development of xylanase assay conditions using Taguchi methodology.

PubMed

Prasad Uday, Uma Shankar; Bandyopadhyay, Tarun Kanti; Bhunia, Biswanath

2016-11-01

The present investigation is mainly concerned with the rapid development of extracellular xylanase assay conditions by using Taguchi methodology. The extracellular xylanase was produced from Aspergillus niger (KP874102.1), a new strain isolated from a soil sample of the Baramura forest, Tripura West, India. Four physical parameters including temperature, pH, buffer concentration and incubation time were considered as key factors for xylanase activity and were optimized using Taguchi robust design methodology for enhanced xylanase activity. The main effect, interaction effects and optimal levels of the process factors were determined using signal-to-noise (S/N) ratio. The Taguchi method recommends the use of S/N ratio to measure quality characteristics. Based on analysis of the S/N ratio, optimal levels of the process factors were determined. Analysis of variance (ANOVA) was performed to evaluate statistically significant process factors. ANOVA results showed that temperature contributed the maximum impact (62.58%) on xylanase activity, followed by pH (22.69%), buffer concentration (9.55%) and incubation time (5.16%). Predicted results showed that enhanced xylanase activity (81.47%) can be achieved with pH 2, temperature 50°C, buffer concentration 50 Mm and incubation time 10 min.

Storage effects on the Cole-Cole parameters of erythrocyte suspensions.

PubMed

Sezdi, M; Bayik, M; Ulgen, Y

2006-07-01

Chemical alterations of red blood cells (RBCs) during storage eventually affect the electrical properties of blood. In this study, the physiological parameters such as extracellular (SAGM + CPD + residual plasma) Na(+), K(+), Cl(-), pH, 2,3-DPG and ATP together with the Cole-Cole parameters were measured using erythrocyte suspensions from 51 male donors (31 donors form the training set and 20 donors are used for testing), on the 0th, 10th, 21st, 35th and 42nd days of storage. During storage, while the surrounding fluid resistance (R(e)) and the effective cell membrane capacitance (C(m)) increased progressively with time, the intracellular fluid resistance (R(i)) has decreased. Storage of RBCs resulted in a rise in K(+) and a fall in Na(+), Cl(-), pH, 2,3-DPG and ATP. Accordingly, electrical parameters were all correlated with Na(+), K(+), Cl(-), pH and ATP at varying levels. By applying multi-regression analysis, it is concluded that R(i), R(e) and C(m) are appropriate for modeling Na(+), K(+), Cl(-), pH and ATP during storage.

The Award of the PhD Degree in Kenyan Universities: A Quality Assurance Perspective

ERIC Educational Resources Information Center

Ayiro, Laban P.; Sang, James K.

2011-01-01

This article attempts to bring to the fore the need for enhanced quality assurance processes in the award of PhDs by Kenyan universities. The findings reveal that quality challenges exist in the institutional processes established for the award of this advanced degree across the universities in the country. It is hoped that the findings will stir…

40 CFR 436.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Construction Sand and Gravel Subcategory § 436.32 Effluent limitations guidelines representing the degree of... unaltered by man's activities, is or would be less than 6.0 and water quality criteria in water quality... adjusted downward to the pH water quality criterion for the receiving waters. In no case shall a pH...

Physicochemical Characteristic of Municipal Wastewater in Tropical Area: Case Study of Surabaya City, Indonesia

NASA Astrophysics Data System (ADS)

Wijaya, I. M. W.; Soedjono, E. S.

2018-03-01

Municipal wastewater is the main contributor to diverse water pollution problems. In order to prevent the pollution risks, wastewater have to be treated before discharged to the main water. Selection of appropriated treatment process need the characteristic information of wastewater as design consideration. This study aims to analyse the physicochemical characteristic of municipal wastewater from inlet and outlet of ABR unit around Surabaya City. Medokan Semampir and Genteng Candi Rejo has been selected as wastewater sampling point. The samples were analysed in laboratory with parameters, such as pH, TSS, COD, BOD, NH4 +, NO3 -, NO2 -, P, and detergent. The results showed that all parameters in both locations are under the national standard of discharged water quality. In other words, the treated water is securely discharged to the river

Fundamental Analysis of the Linear Multiple Regression Technique for Quantification of Water Quality Parameters from Remote Sensing Data. Ph.D. Thesis - Old Dominion Univ.

NASA Technical Reports Server (NTRS)

Whitlock, C. H., III

1977-01-01

Constituents with linear radiance gradients with concentration may be quantified from signals which contain nonlinear atmospheric and surface reflection effects for both homogeneous and non-homogeneous water bodies provided accurate data can be obtained and nonlinearities are constant with wavelength. Statistical parameters must be used which give an indication of bias as well as total squared error to insure that an equation with an optimum combination of bands is selected. It is concluded that the effect of error in upwelled radiance measurements is to reduce the accuracy of the least square fitting process and to increase the number of points required to obtain a satisfactory fit. The problem of obtaining a multiple regression equation that is extremely sensitive to error is discussed.

Physicochemical quality and health implications of bottled water brands sold in Ethiopia.

PubMed

Amogne, Wossen T; Gizaw, Melaku; Abera, Daniel

2015-06-01

Water bottling companies often assert that their products are of the highest quality and are conforming to the standards. The objective of the study was to assess the physicochemical quality of bottled waters consumed in Ethiopia and to compare the findings with the national and international water quality standards. Eleven domestic and two imported bottled water brands were randomly purchased in Addis Ababa, Ethiopia at three different occasions from July 2013 to May 2014. A total of 39 composite samples were examined for aggregate parameters, major anions, and common cations in accordance with the procedures described in the standard methods. We found that 7.7% of the samples were containing higher levels of alkalinity, hardness, total dissolved solids, pH, HCO3-, Na+, and Ca2+ than the national standards and the WHO guidelines. However, the deviations from standards for all the above parameters were not statistically significant (one-sample t-test, P>0.05). Conversely, in some of the brands, some of the essential elements like Ca2+, K+, Mg2+, and F- were found at very low concentrations. The rest of the parameters, including CO3(2-), SO4(2-), PO4(3-) (orthophosphates), Cl-, F-, NO3-, NO2-, K+, Mg2+, Fe, Mn, Cr, Cd, Cu, Ni, and Pb were within the acceptable ranges in all the brands. Bottled water brands containing very high concentrations of dissolved substances may pose health risks for individuals living with heart and kidney related problems. On the other hand, brands having chemicals lower than the optimum level may also harm the health of consumers who choose those brands as a sole source of drinking water. Thus, we suggest those responsible authorities to ensure regular monitoring and testing for chemical compositions of bottled water.

Valuing water quality in urban watersheds: A comparative analysis of Johnson Creek, Oregon, and Burnt Bridge Creek, Washington

NASA Astrophysics Data System (ADS)

Netusil, Noelwah R.; Kincaid, Michael; Chang, Heejun

2014-05-01

This study uses the hedonic price method to investigate the effect of five water quality parameters on the sale price of single-family residential properties in two urbanized watersheds in the Portland, Oregon-Vancouver, Washington metropolitan area. Water quality parameters include E. coli or fecal coliform, which can affect human health, decrease water clarity and generate foul odors; pH, dissolved oxygen, and stream temperature, which can impact fish and wildlife populations; and total suspended solids, which can affect water clarity, aquatic life, and aesthetics. Properties within ¼ mile, ½, mile, one mile, or more than one mile from Johnson Creek are estimated to experience an increase in sale price of 13.71%, 7.05%, 8.18%, and 3.12%, respectively, from a one mg/L increase in dissolved oxygen levels during the dry season (May-October). Estimates for a 100 count per 100 mL increase in E. coli during the dry season are -2.81% for properties within ¼ mile of Johnson Creek, -0.86% (½ mile), -1.19% (one mile), and -0.71% (greater than one mile). Results for properties in Burnt Bridge Creek include a significantly positive effect for a one mg/L increase in dissolved oxygen levels during the dry season for properties within ½ mile (4.49%), one mile (2.95%), or greater than one mile from the creek (3.17%). Results for other water quality parameters in Burnt Bridge Creek are generally consistent with a priori expectations. Restoration efforts underway in both study areas might be cost justified based on their estimated effect on property sale prices.

Improving on the diagnostic characteristics of echocardiography for pulmonary hypertension.

PubMed

Broderick-Forsgren, Kathleen; Davenport, Clemontina A; Sivak, Joseph A; Hargett, Charles William; Foster, Michael C; Monteagudo, Andrew; Armour, Alicia; Rajagopal, Sudarshan; Arges, Kristine; Velazquez, Eric J; Samad, Zainab

2017-09-01

This retrospective study evaluated the diagnostic characteristics of a combination of echocardiographic parameters for pulmonary hypertension (PH). Right ventricular systolic pressure (RVSP) estimation by echocardiography (echo) is used to screen for PH. However, the sensitivity of this method is suboptimal. We hypothesized that RVSP estimation in conjunction with other echo parameters would improve the value of echo for PH. The Duke Echo database was queried for adult patients with known or suspected PH who had undergone both echo and right heart catheterization (RHC) within a 24 h period between 1/1/2008 and 12/31/2013. Patients with complex congenital heart disease, heart transplantation, ventricular assist device, or on mechanical ventilation at time of study were excluded. Diagnostic characteristics of several echo parameters (right atrial enlargement, pulmonary artery (PA) enlargement, RV enlargement, RV dysfunction, and RVSP) for PH (mean PA pressure 25 mmHg on RHC) were evaluated among 1007 patients. RVSP ≥40 had a sensitivity of 77% (accuracy 77), while RVSP ≥35 had the highest sensitivity at 88% (81% accuracy). PA enlargement had the lowest sensitivity at 17%. The area under the curve (AUC) for RVSP was 0.844. A model including RVSP, RA, PA, RV enlargement and RV dysfunction had a higher AUC (AUC = 0.87) than RVSP alone. The value of echo as a screening test for PH is improved by a model incorporating a lower RVSP in addition to other right heart parameters. These findings need to be validated in prospective cohorts.

PH-dependence of detergent-induced hemolysis and vesiculation of erythrocytes.

PubMed

Chernitsky, E A; Rozin, V V; Senkovich, O A

2001-01-01

The influence of pH of the medium on the parameters of detergent-induced fast hemolysis and vesiculation of human erythrocytes was studied. In the range of pH 6.3-7.2 neither the extent nor the rate of the vesiculation induced by 25 microM sodium dodecyl sulfate (SDS) changed. However, a decrease of pH from 8.0 to 5.8 strongly modified both the extent and the rate of the hemolysis induced by SDS. Within the range of pH 8.0-6.4, the effect can be ascribed to the increase of the positive charge of the membrane. This could lead to the accumulation of the membrane-bound anion detergent and, hence, to the change of the hemolysis parameters. Non-charged detergent Triton X-100 did not display any pH-dependence. At pH between 6.4 and 5.8 the extent and rate of hemolysis changed in a complicated manner. The kinetic curves of hemolysis could be approximated by a single exponential within the pH range between 8.0 and 7.2. Upon further reduction of pH, a second exponential component, with a larger time constant, appeared in the kinetic curves. At 5.8 < pH < 7.2, the contribution of the "fast" hemolysis dropped virtually to zero, with pK about 6.0. This points to a structural transition of the membrane, possibly involving histidine. We suggest that the parameters of the detergent-induced hemolysis are sensitive to the changes of the charge and structural state of erythrocyte membrane.

Crystallization and preliminary X-ray diffraction studies of polyketide synthase-1 (PKS-1) from Cannabis sativa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taguchi, Chiho; Quantum Beam Science Directorate, Japan Atomic Energy Agency; Taura, Futoshi

Polyketide synthase-1 from C. sativa has been crystallized. The crystal diffracted to 1.55 Å resolution with sufficient quality for further structure determination. Polyketide synthase-1 (PKS-1) is a novel type III polyketide synthase that catalyzes the biosynthesis of hexanoyl triacetic acid lactone in Cannabis sativa (Mexican strain). PKS-1 was overproduced in Escherichia coli, purified and finally crystallized in two different space groups. The crystal obtained in 0.1 M HEPES buffer pH 7.5 containing 0.2 M calcium acetate and 20%(w/v) polyethylene glycol 3350 diffracted to 1.65 Å resolution and belonged to space group P1, with unit-cell parameters a = 54.3, b =more » 59.3, c = 62.6 Å, α = 69, β = 81, γ = 80°. Another crystal obtained in 0.1 M HEPES buffer pH 7.5 containing 0.2 M sodium chloride and 20%(w/v) polyethylene glycol 3350 diffracted to 1.55 Å resolution and belonged to space group P2{sub 1}2{sub 1}2{sub 1}, with unit-cell parameters a = 54.3, b = 110, c = 130 Å. These data will enable us to determine the crystal structure of PKS-1.« less

Toxicological study of the Anam River in Otuocha, Anambra State, Nigeria.

PubMed

Igwilo, Innocent O; Afonne, Onyenmechi Johnson; Maduabuchi, Ugwuona John-Moses; Orisakwe, Orish Ebere

2006-01-01

The authors studied the quality of water and soil samples from the Anam River in Nigeria. Using an atomic absorption spectrophotometer, they analyzed levels of lead, cadmium, copper, and nickel. They also analyzed sulfates, nitrates, biological oxygen demand, total hardness, total dissolved solids, pH values, electrical conductivity, chloride, and salinity. The ranges of detected metals were 0.002-0.005 mg/L for cadmium, 0.008-0.016 mg/L for lead, and 0.580-1.345 mg/L for copper. In the soil samples, the authors detected cadmium (0.07-3.45 ppm), copper (4.38-13.54 ppm), lead (0.59-7.34 ppm), and nickel (0.36-5.64 ppm). The mean values of the chemical parameters were 11.34 +/- 1.20 mg/L for total hardness, 4.43 +/- 1.54 mg/L for biological oxygen demand, 20.00 +/- 0.00 mg/L for total dissolved solids, and 0.22 +/- 0.05 mg/L for nitrates. Chloride, salinity, electrical conductivity, and pH values were 8.00 +/- 1.73 mg/L, 14.44 +/- 3.13 mg/L, 19.33 +/- 0.67 ps cm-L, and 7.09 +/- 0.05, respectively. The World Health Organization guidelines for the parameters in soil were exceeded.

Multi-scale analysis of relationship between landscape pattern and urban river water quality in different seasons

NASA Astrophysics Data System (ADS)

Xiao, Rui; Wang, Guofeng; Zhang, Qianwen; Zhang, Zhonghao

2016-05-01

Water quality is highly dependent on the landscape characteristics. In this study, we investigated the relationships between water quality and landscape pattern (composition and configuration) in Huzhou City, China. The water quality variables, including pH, dissolved oxygen (DO), chemical oxygen demand (CODMn), Biochemical Oxygen Demand (BOD), NH3-N, petroleum, dissolved total phosphorus (DTP), and total nitrogen (TN) in low water, normal water and flood periods were identified by investigating 34 sampling sites in Huzhou City during the period from 2001 to 2007. Landscape composition and landscape configuration metrics were calculated for different scales. It was found that scales and seasons both play important role when analyzing the relationships between landscape characteristics of different land use types. The results implied that some water quality parameters such as CODMn, petroleum are more polluted in flood period than the other two seasons at different scales, while DTP and TN are more polluted in low water period. Influences of different landscape metrics on water quality should operate at different spatial scales. The results shown in this paper will effectively provide scientific basis for the policy making in sustainable development of water environment.

Multi-scale analysis of relationship between landscape pattern and urban river water quality in different seasons.

PubMed

Xiao, Rui; Wang, Guofeng; Zhang, Qianwen; Zhang, Zhonghao

2016-05-05

Water quality is highly dependent on the landscape characteristics. In this study, we investigated the relationships between water quality and landscape pattern (composition and configuration) in Huzhou City, China. The water quality variables, including pH, dissolved oxygen (DO), chemical oxygen demand (CODMn), Biochemical Oxygen Demand (BOD), NH3-N, petroleum, dissolved total phosphorus (DTP), and total nitrogen (TN) in low water, normal water and flood periods were identified by investigating 34 sampling sites in Huzhou City during the period from 2001 to 2007. Landscape composition and landscape configuration metrics were calculated for different scales. It was found that scales and seasons both play important role when analyzing the relationships between landscape characteristics of different land use types. The results implied that some water quality parameters such as CODMn, petroleum are more polluted in flood period than the other two seasons at different scales, while DTP and TN are more polluted in low water period. Influences of different landscape metrics on water quality should operate at different spatial scales. The results shown in this paper will effectively provide scientific basis for the policy making in sustainable development of water environment.

Morphology, geology and water quality assessment of former tin mining catchment.

PubMed

Ashraf, Muhammad Aqeel; Maah, Mohd Jamil; Yusoff, Ismail

2012-01-01

Bestari Jaya, former tin mining catchment covers an area of 2656.31 hectares comprised of four hundred and forty-two different-size lakes and ponds. The present study area comprise of 92 hectares of the catchment that include four large size lakes. Arc GIS version 9.2 used to develop bathymetric map, Global Positioning System (GPS) for hydrographical survey and flow meter was utilized for water discharge analysis (flow routing) of the catchment. The water quality parameters (pH, temperature, electric conductivity, dissolved oxygen DO, total dissolved solids TDS, chlorides, ammonium, nitrates) were analyzed by using Hydrolab. Quality assurance (QA) and quality control (QC) procedures were strictly followed throughout the field work and data analysis. Different procedures were employed to evaluate the analytical data and to check for possible transcription or dilution errors, changes during analysis, or unusual or unlikely values. The results obtained are compared with interim national water quality standards for Malaysia indicates that water quality of area is highly degraded. It is concluded that Bestri Jaya ex-mining catchment has a high pollution potential due to mining activities and River Ayer Hitam, recipient of catchment water, is a highly polluted river.

Water-quality data from an earthen dam site in southern Westchester County, New York, 2015

USGS Publications Warehouse

Chu, Anthony; Noll, Michael L.

2017-10-11

The U.S. Geological Survey, in cooperation with the New York City Department of Environmental Protection, sampled 37 sites in the reservoir area for nutrients, major ions, metals, pesticides and their degradates, volatile organic compounds, temperature, pH, and specific conductance during fall 2015. Data collection was done to characterize the local groundwater-flow system and identify potential sources of seeps from the southern embankment at the Hillview Reservoir. Water-quality samples were collected in accordance with standard U.S. Geological Survey methods at 37 sites in and adjacent to Hillview Reservoir. These 37 sites were sampled to determine (1) baseline water-quality conditions of the saturated, low-permeability sediments that compose the earthen embankment that surrounds the reservoir, (2) water-quality conditions in the southwestern part of the study area in relation to the seeps on the embankment, and (3) temporal variation of water-quality conditions between 2006 and 2015 (not included in this report). The physical parameters and the results of the water-quality analysis from the 37 sites are included in this report and can be downloaded from the U.S. Geological Survey National Water Information System website.

Morphology, Geology and Water Quality Assessment of Former Tin Mining Catchment

PubMed Central

Ashraf, Muhammad Aqeel; Maah, Mohd. Jamil; Yusoff, Ismail

2012-01-01

Bestari Jaya, former tin mining catchment covers an area of 2656.31 hectares comprised of four hundred and forty-two different-size lakes and ponds. The present study area comprise of 92 hectares of the catchment that include four large size lakes. Arc GIS version 9.2 used to develop bathymetric map, Global Positioning System (GPS) for hydrographical survey and flow meter was utilized for water discharge analysis (flow routing) of the catchment. The water quality parameters (pH, temperature, electric conductivity, dissolved oxygen DO, total dissolved solids TDS, chlorides, ammonium, nitrates) were analyzed by using Hydrolab. Quality assurance (QA) and quality control (QC) procedures were strictly followed throughout the field work and data analysis. Different procedures were employed to evaluate the analytical data and to check for possible transcription or dilution errors, changes during analysis, or unusual or unlikely values. The results obtained are compared with interim national water quality standards for Malaysia indicates that water quality of area is highly degraded. It is concluded that Bestri Jaya ex-mining catchment has a high pollution potential due to mining activities and River Ayer Hitam, recipient of catchment water, is a highly polluted river. PMID:22761549

Multi-scale analysis of relationship between landscape pattern and urban river water quality in different seasons

PubMed Central

Xiao, Rui; Wang, Guofeng; Zhang, Qianwen; Zhang, Zhonghao

2016-01-01

Water quality is highly dependent on the landscape characteristics. In this study, we investigated the relationships between water quality and landscape pattern (composition and configuration) in Huzhou City, China. The water quality variables, including pH, dissolved oxygen (DO), chemical oxygen demand (CODMn), Biochemical Oxygen Demand (BOD), NH3-N, petroleum, dissolved total phosphorus (DTP), and total nitrogen (TN) in low water, normal water and flood periods were identified by investigating 34 sampling sites in Huzhou City during the period from 2001 to 2007. Landscape composition and landscape configuration metrics were calculated for different scales. It was found that scales and seasons both play important role when analyzing the relationships between landscape characteristics of different land use types. The results implied that some water quality parameters such as CODMn, petroleum are more polluted in flood period than the other two seasons at different scales, while DTP and TN are more polluted in low water period. Influences of different landscape metrics on water quality should operate at different spatial scales. The results shown in this paper will effectively provide scientific basis for the policy making in sustainable development of water environment. PMID:27147104

The Influence of the Variety, Vineyard, and Vintage on the Romanian White Wines Quality

PubMed Central

Hosu, Anamaria; Floare-Avram, Veronica; Feher, Ioana; Inceu, Mihai

2016-01-01

The wine is one of the most consumed drinks over the world, being subjected to falsification or adulteration regarding the variety, vintage, and geographical region. In this study, the influence of different characteristics of wines (type, production year, and origin) on the total phenolic content, total flavonoids content, antioxidant activity, total sugars content, pH, and 18O/16O isotopic ratio was investigated. The differentiation of selected wines on the basis of tested parameters was investigated using chemometric techniques, such as analysis of variance, cluster analysis, and principal component analysis. The experimental results are in agreement with other outcomes and allow concluding that variety and vineyard have the major influence on the studied parameters, but, also, statistical interaction effect between year and vineyard and year and variety is observed in some cases. The obtained results have demonstrated that these parameters together with chemometric techniques show a significant potential to be used for discrimination of white wines. PMID:27840767

Beer fermentation: monitoring of process parameters by FT-NIR and multivariate data analysis.

PubMed

Grassi, Silvia; Amigo, José Manuel; Lyndgaard, Christian Bøge; Foschino, Roberto; Casiraghi, Ernestina

2014-07-15

This work investigates the capability of Fourier-Transform near infrared (FT-NIR) spectroscopy to monitor and assess process parameters in beer fermentation at different operative conditions. For this purpose, the fermentation of wort with two different yeast strains and at different temperatures was monitored for nine days by FT-NIR. To correlate the collected spectra with °Brix, pH and biomass, different multivariate data methodologies were applied. Principal component analysis (PCA), partial least squares (PLS) and locally weighted regression (LWR) were used to assess the relationship between FT-NIR spectra and the abovementioned process parameters that define the beer fermentation. The accuracy and robustness of the obtained results clearly show the suitability of FT-NIR spectroscopy, combined with multivariate data analysis, to be used as a quality control tool in the beer fermentation process. FT-NIR spectroscopy, when combined with LWR, demonstrates to be a perfectly suitable quantitative method to be implemented in the production of beer. Copyright © 2014 Elsevier Ltd. All rights reserved.

Impact of physicochemical parameters on in vitro assembly and disassembly kinetics of recombinant triple-layered rotavirus-like particles.

PubMed

Mellado, Maria Candida M; Mena, Jimmy A; Lopes, António; Ramírez, Octavio T; Carrondo, Manuel J T; Palomares, Laura A; Alves, Paula M

2009-11-01

Virus-like particles constitute potentially relevant vaccine candidates. Nevertheless, their behavior in vitro and assembly process needs to be understood in order to improve their yield and quality. In this study we aimed at addressing these issues and for that purpose triple- and double-layered rotavirus-like particles (TLP 2/6/7 and DLP 2/6, respectively) size and zeta potential were measured using dynamic light scattering at different physicochemical conditions, namely pH, ionic strength, and temperature. Both TLP and DLP were stable within a pH range of 3-7 and at 5-25 degrees C. Aggregation occurred at 35-45 degrees C and their disassembly became evident at 65 degrees C. The isoelectric points of TLP and DLP were 3.0 and 3.8, respectively. In vitro kinetics of TLP disassembly was monitored. Ionic strength, temperature, and the chelating agent employed determined disassembly kinetics. Glycerol (10%) stabilized TLP by preventing its disassembly. Disassembled TLP was able to reassemble by dialysis at high calcium conditions. VP7 monomers were added to DLP in the presence of calcium to follow in vitro TLP assembly kinetics; its assembly rate being mostly affected by pH. Finally, DLP and TLP were found to coexist under certain conditions as determined from all reaction products analyzed by capillary electrophoresis. Overall, these results contribute to the design of new strategies for the improvement of TLP yield and quality by reducing the VP7 detachment from TLP. Copyright 2009 Wiley Periodicals, Inc.

Optimization of a Coupling Process for Insulin Degludec According to a Quality by Design (QbD) Paradigm.

PubMed

Nie, Lei; Hu, Mingming; Yan, Xu; Guo, Tingting; Wang, Haibin; Zhang, Sheng; Qu, Haibin

2018-05-03

This case study described a successful application of the quality by design (QbD) principles to a coupling process development of insulin degludec. Failure mode effects analysis (FMEA) risk analysis was first used to recognize critical process parameters (CPPs). Five CPPs, including coupling temperature (Temp), pH of desB30 solution (pH), reaction time (Time), desB30 concentration (Conc), and molar equivalent of ester per mole of desB30 insulin (MolE), were then investigated using a fractional factorial design. The curvature effect was found significant, indicating the requirement of second-order models. Afterwards, a central composite design was built with an augmented star and center points study. Regression models were developed for the CPPs to predict the purity and yield of predegludec using above experimental data. The R 2 and adjusted R 2 were higher than 96 and 93% for the two models respectively. The Q 2 values were more than 80% indicating a good predictive ability of models. MolE was found to be the most significant factor affecting both yield and purity of predegludec. Temp, pH, and Conc were also significant for predegludec purity, while Time appeared to remarkably influence the yield model. The multi-dimensional design space and normal operating region (NOR) with a robust setpoint were determined using a probability-based Monte-Carlo simulation method. The verified experimental results showed that the design space was reliable and effective. This study enriches the understanding of acetylation process and is instructional to other complicated operations in biopharmaceutical engineering.

On-line detection of Escherichia coli intrusion in a pilot-scale drinking water distribution system.

PubMed

Ikonen, Jenni; Pitkänen, Tarja; Kosse, Pascal; Ciszek, Robert; Kolehmainen, Mikko; Miettinen, Ilkka T

2017-08-01

Improvements in microbial drinking water quality monitoring are needed for the better control of drinking water distribution systems and for public health protection. Conventional water quality monitoring programmes are not always able to detect a microbial contamination of drinking water. In the drinking water production chain, in addition to the vulnerability of source waters, the distribution networks are prone to contamination. In this study, a pilot-scale drinking-water distribution network with an on-line monitoring system was utilized for detecting bacterial intrusion. During the experimental Escherichia coli intrusions, the contaminant was measured by applying a set of on-line sensors for electric conductivity (EC), pH, temperature (T), turbidity, UV-absorbance at 254 nm (UVAS SC) and with a device for particle counting. Monitored parameters were compared with the measured E. coli counts using the integral calculations of the detected peaks. EC measurement gave the strongest signal compared with the measured baseline during the E. coli intrusion. Integral calculations showed that the peaks in the EC, pH, T, turbidity and UVAS SC data were detected corresponding to the time predicted. However, the pH and temperature peaks detected were barely above the measured baseline and could easily be mixed with the background noise. The results indicate that on-line monitoring can be utilized for the rapid detection of microbial contaminants in the drinking water distribution system although the peak interpretation has to be performed carefully to avoid being mixed up with normal variations in the measurement data. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of concentrate level on feeding behavior and rumen and blood parameters in dairy goats: relationships between behavioral and physiological parameters and effect of between-animal variability.

PubMed

Giger-Reverdin, S; Rigalma, K; Desnoyers, M; Sauvant, D; Duvaux-Ponter, C

2014-07-01

This work aimed first to compare 2 diets differing in their percentage of concentrate [low (LO): 30% concentrate vs. High (HI): 60% concentrate] by measuring simultaneously feeding behavior, rumen parameters, blood and plasma parameters, and milk yield and composition in 8 mid-lactation goats. The second aim was to study the interrelationships between these variables and to analyze the between-animal variability to better understand the between-animal differences in acidosis susceptibility. All of the animals received the 2 diets ad libitum as total mixed ration according to a crossover design of two 4-wk periods. Mean daily DMI was similar between the 2 diets but the variability was higher for the HI than for the LO diet. Goats produced more milk when fed the HI diet compared with the LO diet but with a lower fat:protein ratio (0.81 vs. 0.99). They ate more rapidly the HI than the LO diet but stopped eating sooner after the afternoon feed allowance, and spent less time chewing. The increase in concentrate percentage modified rumen parameters: the pH and acetate:propionate ratio decreased and total VFA, ammonia, and soluble carbohydrate concentrations increased. Hematocrit, plasma NEFA, and blood K and Ca concentrations decreased but glycemia and uremia increased. Other parameters were not modified: milk fat content, blood pH, and bicarbonate and Na concentrations. A large between-animal variability was detected for all the measured parameters, especially for feeding behavior, with important consequences on rumen and blood parameters. This work confirmed the effects of a high percentage of concentrate on feeding behavior, rumen and blood parameters, and milk production, and some known relationships such as the positive link between rumen pH and chewing index. It also pointed out other relationships between parameters seldom measured at the same time, such as rumen redox potential or blood pH and chewing index, or the negative link between blood and rumen pH. When the animals spent a lot of time chewing, they probably produced a lot of saliva that buffered the rumen pH and prevented them from suffering from subacute ruminal acidosis. However, they used part of their blood bicarbonates reserve, which might have induced metabolic acidosis, as rumen and blood pH were inversely related. This could explain why some animals suffer from acidosis and others do not in a herd receiving the same diet, and why some animals seem to suffer more from subacute ruminal acidosis and others from metabolic acidosis. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Does river restoration affect diurnal and seasonal changes to surface water quality? A study along the Thur River, Switzerland.

PubMed

Chittoor Viswanathan, Vidhya; Molson, John; Schirmer, Mario

2015-11-01

Changes in river water quality were investigated along the lower reach of the Thur River, Switzerland, following river restoration and a summer storm event. River restoration and hydrological storm events can each cause dramatic changes to water quality by affecting various bio-geochemical processes in the river, but have to date not been well documented, especially in combination. Evaluating the success of river restoration is often restricted in large catchments due to a lack of high frequency water quality data, which are needed for process understanding. These challenges were addressed in this study by measuring water quality parameters including dissolved oxygen (DO), temperature, pH, electrical conductivity (EC), nitrate and dissolved organic carbon (DOC) with a high temporal frequency (15 min-1h) over selected time scales. In addition, the stable isotopes of water (δD and δ(18)O-H2O) as well as those of nitrate (δ(15)N-NO3(-) and δ(18)O-NO3(-)) were measured to follow changes in water quality in response to the hydrological changes in the river. To compare the spatial distribution of pre- and post-restoration water quality, the sampling stations were chosen upstream and downstream of the restored section. The diurnal and seasonal changes were monitored by conducting 24-hour campaigns in three seasons (winter, summer and autumn) in 2012 and 2013. The amplitude of the diurnal changes of the various observed parameters showed significant seasonal and spatial variability. Biological processes--mainly photosynthesis and respiration--were found to be the major drivers of these diurnal cycles. During low flow in autumn, a reduction of nitrate (attributed to assimilation by autotrophs) in the pre-dawn period and a production of DOC during the daytime (attributed to photosynthesis) were observed downstream of the restored site. Further, a summer storm event was found to override the influence of these biological processes that control the diurnal changes. High frequency daily monitoring of key water quality parameters over different seasons is shown to be essential in evaluating river restoration success. Copyright © 2015 Elsevier B.V. All rights reserved.

Value of Impedance Cardiography during 6‐Minute Walk Test in Pulmonary Hypertension

PubMed Central

Alkukhun, Laith; Arelli, Vineesha; Ramos, José; Newman, Jennie; McCarthy, Kevin; Pichurko, Bohdan; Minai, Omar A.; Dweik, Raed A.

2013-01-01

Abstract Background Methods that predict prognosis and response to therapy in pulmonary hypertension (PH) are lacking. We tested whether the noninvasive estimation of hemodynamic parameters during 6‐minute walk test (6MWT) in PH patients provides information that can improve the value of the test. Methods We estimated hemodynamic parameters during the 6MWT using a portable, signal‐morphology‐based, impedance cardiograph (PhysioFlow Enduro) with real‐time wireless monitoring via a bluetooth USB adapter. Results We recruited 48 subjects in the study (30 with PH and 18 healthy controls). PH patients had significantly lower maximum stroke volume (SV) and CI and slower cardiac output (CO) acceleration and decelerations slopes during the test when compared with healthy controls. In PH patients, CI change was associated with total distance walked (R = 0.62; P < 0.001) and percentage of predicted (R = 0.4, P = 0.03), HR recovery at 1 minute (0.57, P < 0.001), 2 minutes (0.65, P < 0.001), and 3 minutes (0.66, P < 0.001). Interestingly, in PH patients CO change during the test was predominantly related to an increase in SV instead of HR. Conclusions Estimation of hemodynamic parameters such as cardiac index during 6‐minute walk test is feasible and may provide useful information in patients with PH. Clin Trans Sci 2013; Volume #: 1–7 PMID:24330692

Groundwater quality assessment in the village of Lutfullapur Nawada, Loni, District Ghaziabad, Uttar Pradesh, India.

PubMed

Singh, Vinod K; Bikundia, Devendra Singh; Sarswat, Ankur; Mohan, Dinesh

2012-07-01

The groundwater quality for drinking, domestic and irrigation in the village Lutfullapur Nawada, Loni, district Ghaziabad, U.P., India, has been assessed. Groundwater samples were collected, processed and analyzed for temperature, pH, conductivity, salinity, total alkalinity, carbonate alkalinity, bicarbonate alkalinity, total hardness, calcium hardness, magnesium hardness, total solids, total dissolved solids, total suspended solids, nitrate-nitrogen, chloride, fluoride, sulfate, phosphate, silica, sodium, potassium, calcium, magnesium, total chromium, cadmium, copper, iron, nickel, lead and zinc. A number of groundwater samples showed levels of electrical conductivity (EC), alkalinity, chloride, calcium, sodium, potassium and iron exceeding their permissible limits. Except iron, the other metals (Cr, Cd, Cu, Ni, Pb, and Zn) were analyzed below the permissible limits. The correlation matrices for 28 variables were performed. EC, salinity, TS and TDS had significant positive correlations among themselves and also with NO (3) (-) , Cl(-), alkalinity, Na(+), K(+), and Ca(2+). Fluoride was not significantly correlated with any of the parameters. NO (3) (-) was significantly positively correlated with Cl(-), alkalinity, Na(+), K(+) and Ca(2+). Chloride also correlated significantly with alkalinity, Na(+), K(+) and Ca(2+). Sodium showed a strong and positive correlation with K(+) and Ca(2+). pH was negatively correlated with most of the physicochemical parameters. This groundwater is classified as a normal sulfate and chloride type. Base-exchange indices classified 73% of the groundwater sources as the Na(+)-SO (4) (2-) type. The meteoric genesis indices demonstrated that 67% of groundwater sources belong to a deep meteoric water percolation type. Hydrochemical groundwater evaluations revealed that most of the groundwaters belong to the Na(+)-K(+)-Cl(-)-SO (4) (2-) type followed by Na(+)-K(+)-HCO (3) (-) type. Salinity, chlorinity and SAR indices indicated that majority of groundwater samples can be considered suitable for irrigation purposes.

Monitoring of potentially toxic cyanobacteria using an online multi-probe in drinking water sources.

PubMed

Zamyadi, A; McQuaid, N; Prévost, M; Dorner, S

2012-02-01

Toxic cyanobacteria threaten the water quality of drinking water sources across the globe. Two such water bodies in Canada (a reservoir on the Yamaska River and a bay of Lake Champlain in Québec) were monitored using a YSI 6600 V2-4 (YSI, Yellow Springs, Ohio, USA) submersible multi-probe measuring in vivo phycocyanin (PC) and chlorophyll-a (Chl-a) fluorescence, pH, dissolved oxygen, conductivity, temperature, and turbidity in parallel. The linearity of the in vivo fluorescence PC and Chl-a probe measurements were validated in the laboratory with Microcystis aeruginosa (r(2) = 0.96 and r(2) = 0.82 respectively). Under environmental conditions, in vivo PC fluorescence was strongly correlated with extracted PC (r = 0.79) while in vivo Chl-a fluorescence had a weaker relationship with extracted Chl-a (r = 0.23). Multiple regression analysis revealed significant correlations between extracted Chl-a, extracted PC and cyanobacterial biovolume and in vivo fluorescence parameters measured by the sensors (i.e. turbidity and pH). This information will help water authorities select the in vivo parameters that are the most useful indicators for monitoring cyanobacteria. Despite highly toxic cyanobacterial bloom development 10 m from the drinking water treatment plant's (DWTP) intake on several sampling dates, low in vivo PC fluorescence, cyanobacterial biovolume, and microcystin concentrations were detected in the plant's untreated water. The reservoir's hydrodynamics appear to have prevented the transport of toxins and cells into the DWTP which would have deteriorated the water quality. The multi-probe readings and toxin analyses provided critical evidence that the DWTP's untreated water was unaffected by the toxic cyanobacterial blooms present in its source water.

Assessment of physico-chemical quality of borehole and spring water sources supplied to Robe Town, Oromia region, Ethiopia

NASA Astrophysics Data System (ADS)

Shigut, Dagim Abera; Liknew, Geremew; Irge, Dejene Disasa; Ahmad, Tanweer

2017-03-01

The study was carried out to find the physico-chemical water quality of borehole and spring water supplied to Robe Town. For this study, a total of six water samples were collected from three borehole and three spring water sources. The analyses for 14 physico-chemical parameters, pH, turbidity, electrical conductivity, total dissolved solids, total suspended solids total hardness cations (Ca2+, Mg2+), anions (NO2 -, NO3 -, SO4 2- and PO4 3-) and heavy metals (Fe and Mn), were done in the laboratory by adopting standard procedures suggested by the American Public Health Association (APHA). Descriptive statistics were used to describe data, while Pearson correlation was used to determine the influences of the physico-chemical variables. The single factor analysis of variance ( t test) was used to determine possible differences between the borehole and spring water, while means plots were used for further structure detection. From the total samples analyzed, most of the samples comply with the water quality guidelines of Ethiopian limit, WHO and U.SEPA. The pH of the water samples from borehole groundwater source was found to be slightly acidic and bove the maximum permissible limit (MPL). High concentration of Fe and Mn that exceeds the MPL set by WHO was found in the three boreholes. The spring water sources were found to be better for drinking than borehole water sources.

Marine water quality under climate change conditions/scenarios

NASA Astrophysics Data System (ADS)

Rizzi, Jonathan; Torresan, Silvia; Critto, Andrea; Zabeo, Alex; Brigolin, Daniele; Carniel, Sandro; Pastres, Roberto; Marcomini, Antonio

2016-04-01

The increase of sea temperature and the changes in marine currents are generating impacts on coastal waters such as changes in water biogeochemical and physical parameters (e.g. primary production, pH, salinity) leading to progressive degradation of the marine environment. With the main aim of analysing the potential impacts of climate change on coastal water quality, a Regional Risk Assessment (RRA) methodology was developed and applied to coastal marine waters of the North Adriatic (i.e. coastal water bodies of the Veneto and Friuli Venezia Giulia regions, Italy). RRA integrates the outputs of regional models providing information on macronutrients (i.e. dissolved inorganic nitrogen e reactive phosphorus), dissolved oxygen, pH, salinity and temperature, etc., under future climate change scenarios with site-specific environmental and socio-economic indicators (e.g. biotic index, presence and extension of seagrasses, presence of aquaculture). The presented approach uses Geographic Information Systems to manage, analyse, and visualize data and employs Multi-Criteria Decision Analysis for the integration of stakeholders preferences and experts judgments into the evaluation process. RRA outputs are hazard, exposure, vulnerability, risk and damage maps useful for the identification and prioritization of hot-spot areas and vulnerable targets in the considered region. Therefore, the main aim of this contribution is to apply the RRA methodology to integrate, visualize, and rank according to spatial distribution, physical and chemical data concerning the coastal waters of the North Adriatic Sea in order to predict possible changes of the actual water quality.

ANFIS-based modelling for coagulant dosage in drinking water treatment plant: a case study.

PubMed

Heddam, Salim; Bermad, Abdelmalek; Dechemi, Noureddine

2012-04-01

Coagulation is the most important stage in drinking water treatment processes for the maintenance of acceptable treated water quality and economic plant operation, which involves many complex physical and chemical phenomena. Moreover, coagulant dosing rate is non-linearly correlated to raw water characteristics such as turbidity, conductivity, pH, temperature, etc. As such, coagulation reaction is hard or even impossible to control satisfactorily by conventional methods. Traditionally, jar tests are used to determine the optimum coagulant dosage. However, this is expensive and time-consuming and does not enable responses to changes in raw water quality in real time. Modelling can be used to overcome these limitations. In this study, an Adaptive Neuro-Fuzzy Inference System (ANFIS) was used for modelling of coagulant dosage in drinking water treatment plant of Boudouaou, Algeria. Six on-line variables of raw water quality including turbidity, conductivity, temperature, dissolved oxygen, ultraviolet absorbance, and the pH of water, and alum dosage were used to build the coagulant dosage model. Two ANFIS-based Neuro-fuzzy systems are presented. The two Neuro-fuzzy systems are: (1) grid partition-based fuzzy inference system (FIS), named ANFIS-GRID, and (2) subtractive clustering based (FIS), named ANFIS-SUB. The low root mean square error and high correlation coefficient values were obtained with ANFIS-SUB method of a first-order Sugeno type inference. This study demonstrates that ANFIS-SUB outperforms ANFIS-GRID due to its simplicity in parameter selection and its fitness in the target problem.

Soil properties evolution after irrigation with reclaimed water

NASA Astrophysics Data System (ADS)

Leal, M.; González-Naranjo, V.; de Miguel, A.; Martínez-Hernández, V.; Lillo, J.

2012-04-01

Many arid and semi-arid countries are forced to look for new and alternative water sources. The availability of suitable quality water for agriculture in these regions often is threatened. In this context of water scarcity, the reuse of treated wastewater for crop irrigation could represent a feasible solution. Through rigorous planning and management, irrigation with reclaimed water presents some advantages such as saving freshwater, reducing wastewater discharges into freshwater bodies and decreasing the amount of added fertilizers due to the extra supply of nutrients by reclaimed water. The current study, which involves wastewater reuse in agriculture, has been carried out in the Experimental Plant of Carrión de los Céspedes (Sevile, Spain). Here, two survey parcels equally designed have been cultivated with Jatropha curcas L, a bioenergetic plant and a non-interfering food security crop. The only difference between the two parcels lies on the irrigation water quality: one is irrigated with groundwater and another one with reclaimed water. The main aim of this study focuses on analysing the outstanding differences in soil properties derived from irrigation with two water qualities, due to their implications for plant growth. To control and monitor the soil variables, soil samples were collected before and after irrigation in the two parcels. pH, electrical conductivity, cation exchange capacity, exchangeable cations (Ca2+, Mg2+, Na+ and K+), kjeldahl nitrogen, organic matter content and nutrients (boron, phosphorus, nitrogen, potassium) were measured. Data were statistically analyzed using the R package. To evaluate the variance ANOVA test was used and to obtain the relations between water quality and soil parameters, Pearson correlation coefficient was computed. According to other authors, a decrease in the organic matter content and an increase of parameters such as pH, electrical conductivity and some exchangeable cations were expected. To date and after one year of irrigation, no significant differences have been found among the soil properties of the two parcels. The results show in one hand, a slightly decrease in phosphorus, nitrates and electrical conductivity and on the other hand, an increase of organic matter. These trends should be contrasted by new soil quality measurements. The implications on vegetation growth, oil production and nutrients assimilation derived from the irrigation with reclaimed water should be also evaluated over time.

Bench-scale evaluation of drinking water treatment parameters on iron particles and water quality.

PubMed

Rahman, M Safiur; Gagnon, Graham A

2014-01-01

Discoloration of water resulting from suspended iron particles is one of the main customer complaints received by water suppliers. However, understanding of the mechanisms of discoloration as well as role of materials involved in the process is limited. In this study, an array of bench scale experiments were conducted to evaluate the impact of the most common variables (pH, PO4, Cl2 and DOM) on the properties of iron particles and suspensions derived from the oxygenation of Fe(II) ions in NaHCO3 buffered synthetic water systems. The most important factors as well as their rank influencing iron suspension color and turbidity formation were identified for a range of water quality parameters. This was accomplished using a 2(4) full factorial design approach at a 95% confidence level. The statistical analysis revealed that phosphate was found to be the most significant factor to alter color (contribution: 37.9%) and turbidity (contribution: 45.5%) in an iron-water system. A comprehensive study revealed that phosphate and chlorine produced iron suspension with reduced color and turbidity, made ζ-potential more negative, reduced the average particle size, and increased iron suspension stability. In the presence of DOM, color was observed to increase but a reverse trend was observed to decrease the turbidity and to alter particle size distribution. HPSEC results suggest that higher molecular weight fractions of DOM tend to adsorb onto the surfaces of iron particles at early stages, resulting in alteration of the surface charge of iron particles. This in turn limits particles aggregation and makes iron colloids highly stable. In the presence of a phosphate based corrosion inhibitor, this study demonstrated that color and turbidity resulting from suspended iron were lower at a pH value of 6.5 (compared to pH of 8.5). The same trend was observed in presence of DOM. This study also suggested that iron colloid suspension color and turbidity in chlorinated drinking water systems could be lower than non-chlorinated systems. Copyright © 2013 Elsevier Ltd. All rights reserved.

Resource stoichiometry and availability modulate species richness and biomass of tropical litter macro-invertebrates.

PubMed

Jochum, Malte; Barnes, Andrew D; Weigelt, Patrick; Ott, David; Rembold, Katja; Farajallah, Achmad; Brose, Ulrich

2017-09-01

High biodiversity and biomass of soil communities are crucial for litter decomposition in terrestrial ecosystems such as tropical forests. However, the leaf litter that these communities consume is of particularly poor quality as indicated by elemental stoichiometry. The impact of resource quantity, quality and other habitat parameters on species richness and biomass of consumer communities is often studied in isolation, although much can be learned from simultaneously studying both community characteristics. Using a dataset of 780 macro-invertebrate consumer species across 32 sites in tropical lowland rain forest and agricultural systems on Sumatra, Indonesia, we investigated the effects of basal resource stoichiometry (C:X ratios of N, P, K, Ca, Mg, Na, S in local leaf litter), litter mass (basal resource quantity and habitat space), plant species richness (surrogate for litter habitat heterogeneity), and soil pH (acidity) on consumer species richness and biomass across different consumer groups (i.e. 3 feeding guilds and 10 selected taxonomic groups). In order to distinguish the most important predictors of consumer species richness and biomass, we applied a standardised model averaging approach investigating the effects of basal resource stoichiometry, litter mass, plant species richness and soil pH on both consumer community characteristics. This standardised approach enabled us to identify differences and similarities in the magnitude and importance of such effects on consumer species richness and biomass. Across consumer groups, we found litter mass to be the most important predictor of both species richness and biomass. Resource stoichiometry had a more pronounced impact on consumer species richness than on their biomass. As expected, taxonomic groups differed in which resource and habitat parameters (basal resource stoichiometry, litter mass, plant species richness and pH) were most important for modulating their community characteristics. The importance of litter mass for both species richness and biomass indicates that these tropical consumers strongly depend on habitat space and resource availability. Our study supports previous theoretical work indicating that consumer species richness is jointly influenced by resource availability and the balanced supply of multiple chemical elements in their resources. © 2017 The Authors. Journal of Animal Ecology © 2017 British Ecological Society.

Effect of dietary selenium source (organic vs. mineral) and muscle pH on meat quality characteristics of pigs.

PubMed

Calvo, Luis; Toldrá, Fidel; Rodríguez, Ana I; López-Bote, Clemente; Rey, Ana I

2017-01-01

This study evaluates the effect of organic (Se-enriched yeast; SeY) versus inorganic selenium (sodium selenite; SeS) supplementation and the different response of selenium source according to muscle pH on pork meat quality characteristics. Pigs ( n  = 30) were fed the Se-supplemented diets (0.3 mg/kg) for 65 days. Neither electric conductivity (EC) nor drip loss were affected by the selenium source. The SeY group had lower TBARS in muscle samples after day 7 of refrigerated storage and higher a * values on days 1 and 7 than the SeS group. The effect of dietary selenium source on some meat quality characteristics was affected by muscle pH. Hence, as the muscle pH increases, the drip loss decreases but this effect is more marked with the dietary organic Se enrichment. Muscle pH seems to modulate the action of selenium in pork, especially some meat characteristics such as drip loss.

Application of Aquaculture Monitoring System Based on CC2530

NASA Astrophysics Data System (ADS)

Chen, H. L.; Liu, X. Q.

In order to improve the intelligent level of aquaculture technology, this paper puts forward a remote wireless monitoring system based on ZigBee technology, GPRS technology and Android mobile phone platform. The system is composed of wireless sensor network (WSN), GPRS module, PC server, and Android client. The WSN was set up by CC2530 chips based on ZigBee protocol, to realize the collection of water quality parameters such as the water level, temperature, PH and dissolved oxygen. The GPRS module realizes remote communication between WSN and PC server. Android client communicates with server to monitor the level of water quality. The PID (proportion, integration, differentiation) control is adopted in the control part, the control commands from the android mobile phone is sent to the server, the server again send it to the lower machine to control the water level regulating valve and increasing oxygen pump. After practical testing to the system in Liyang, Jiangsu province, China, temperature measurement accuracy reaches 0.5°C, PH measurement accuracy reaches 0.3, water level control precision can be controlled within ± 3cm, dissolved oxygen control precision can be controlled within ±0.3 mg/L, all the indexes can meet the requirements, this system is very suitable for aquaculture.

β-1,3-Glucanase from Delftia tsuruhatensis Strain MV01 and Its Potential Application in Vinification ▿ † §

PubMed Central

Blättel, V.; Larisika, M.; Pfeiffer, P.; Nowak, C.; Eich, A.; Eckelt, J.; König, H.

2011-01-01

During vinification microbial activities can spoil wine quality. As the wine-related lactic acid bacterium Pediococcus parvulus is able to produce slimes consisting of a β-1,3-glucan, must and wine filtration can be difficult or impossible. In addition, the metabolic activities of several wild-type yeasts can also negatively affect wine quality. Therefore, there is a need for measures to degrade the exopolysaccharide from Pediococcus parvulus and to inhibit the growth of certain yeasts. We examined an extracellular β-1,3-glucanase from Delftia tsuruhatensis strain MV01 with regard to its ability to hydrolyze both polymers, the β-1,3-glucan from Pediococcus and that from yeast cell walls. The 29-kDa glycolytic enzyme was purified to homogeneity. It exhibited an optimal activity at 50°C and pH 4.0. The sequencing of the N terminus revealed significant similarities to β-1,3-glucanases from different bacteria. In addition, the investigations indicated that this hydrolytic enzyme is still active under wine-relevant parameters such as elevated ethanol, sulfite, and phenol concentrations as well as at low pH values. Therefore, the characterized enzyme seems to be a useful tool to prevent slime production and undesirable yeast growth during vinification. PMID:21169426

Effect of pieces size of Empty Fruit Bunches (EFB) on composting of EFB mixed with activated liquid organic fertilizer

NASA Astrophysics Data System (ADS)

Trisakti, B.; Mhardela, P.; Husaini, T.; Irvan; Daimon, H.

2018-02-01

This research was to determine the effect of pieces sizes of oil palm empty fruit bunch (EFB) on the composting of EFB mixed with activated liquid organic fertilizer (ALOF) in a basket composter in order to obtain high quality compost. The composting process was started by cutting the EFB into pieces with varies sizes, inserting the EFB pieces into basket composter (33 cm W × 28 cm L × 40 cm H), and adding ALOF until moisture content (MC) in the range of 55-65%. During composting, the compost pile was turned every 3 days and the MC was maintained at 55-65% range by adding the ALOF. The sizes of the EFB pieces were varied into <1, 1-3, 4-7, 8-11, and 12-15 cm. The parameters analysed during the composting were temperature, pH, MC, compost weight, water holding capacity (WHC), CN ratio, and the quality of the final compost. Composting was carried out for 40 days and the best result obtained at EFB pieces size was 1-3 cm with compost characteristic were pH 9.0; MC 52.59%; WHC 76%; CN ratio 12.15; N 1.96%; P 0.58%; and K 0. 95%.

Effect of fermentation and sterilization on anthocyanins in blueberry.

PubMed

Nie, Qixing; Feng, Lei; Hu, Jielun; Wang, Sunan; Chen, Haihong; Huang, Xiaojun; Nie, Shaoping; Xiong, Tao; Xie, Mingyong

2017-03-01

Blueberry products have various health benefits due to their high content of dietary anthocyanins. The aim of this study was to investigate the impact of fermentation and sterilization on total anthocyanin content, composition and some quality attributes of blueberry puree. The blueberry puree used here was fermented for 40 h at 37 °C by Lactobacillus after sterilization. The method of ultra-performance liquid chromatography-mass spectrometry was optimized for the rapid analysis of anthocyanins. Quality attributes including pH, color, total soluble solids and viscosity were measured. A total of 21 anthocyanins and five anthocyanidins were quantified by ultra-performance liquid chromatography. Fermented blueberry had reduced total anthocyanin content (29%) and levels of individual anthocyanins compared with fresh blueberry. Total anthocyanin content was decreased 46% by sterilization, and different degradation behavior of individual anthocyanin was appeared between fermented and sterilized-fermented blueberry puree. Fermentation and sterilization decreased the total soluble solids and pH and changed color parameters, while minimally influencing viscosity. The loss of total anthocyanin content by fermentation was related to the unstable structure of blueberry anthocyanins. Anthocyanins are sensitive to temperature (>80 °C), and degradation of anthocyanins by sterilization in blueberry should be considered in the fermentation procedure. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Beta-1,3-glucanase from Delftia tsuruhatensis strain MV01 and its potential application in vinification.

PubMed

Blättel, V; Larisika, M; Pfeiffer, P; Nowak, C; Eich, A; Eckelt, J; König, H

2011-02-01

During vinification microbial activities can spoil wine quality. As the wine-related lactic acid bacterium Pediococcus parvulus is able to produce slimes consisting of a β-1,3-glucan, must and wine filtration can be difficult or impossible. In addition, the metabolic activities of several wild-type yeasts can also negatively affect wine quality. Therefore, there is a need for measures to degrade the exopolysaccharide from Pediococcus parvulus and to inhibit the growth of certain yeasts. We examined an extracellular β-1,3-glucanase from Delftia tsuruhatensis strain MV01 with regard to its ability to hydrolyze both polymers, the β-1,3-glucan from Pediococcus and that from yeast cell walls. The 29-kDa glycolytic enzyme was purified to homogeneity. It exhibited an optimal activity at 50°C and pH 4.0. The sequencing of the N terminus revealed significant similarities to β-1,3-glucanases from different bacteria. In addition, the investigations indicated that this hydrolytic enzyme is still active under wine-relevant parameters such as elevated ethanol, sulfite, and phenol concentrations as well as at low pH values. Therefore, the characterized enzyme seems to be a useful tool to prevent slime production and undesirable yeast growth during vinification.

Spoilage of sous vide cooked salmon (Salmo salar) stored under refrigeration.

PubMed

Díaz, P; Garrido, M D; Bañón, S

2011-02-01

The spoilage of Sous Vide 'SV' cooked salmon stored under refrigeration was studied. Samples were packaged under vacuum in polyamide-polypropylene pouches, cooked at an oven temperature/time of 80 (°)C/45 min, quickly chilled at 3 (°)C and stored at 2 (°)C for 0, 5 or 10 weeks for catering use. Microbial (aerobic and anaerobic psychrotrophs, lactic acid bacteria, molds and yeasts and Enterobacteriaceae), physical-chemical (pH, water activity, TBARS, acidity, L*a*b* color, texture profile analysis and shear force) and sensory (appearance, odor, flavor, texture and overall quality) parameters were determined. SV processing prevented the growth of aerobic and anaerobic psychrotrophs, lactic acid bacteria, molds and yeasts and Enterobacteriaceae. There were no relevant changes in pH, water activity, TBARS, CIELab color associated with cooked salmon spoilage. Instrumental texture data were contradictory. Slight decrease in lactic acid levels was found. In contrast, the SV cooked salmon suffered considerable sensory deterioration during its refrigerated storage, consisting of severe losses of cooked salmon odor and flavor, slight rancidity, discoloration associated with white precipitation, and moderates softness, and loss of chewiness and juiciness. No acidification, putrefaction or relevant rancidity was detected. The sensory spoilage preceded microbiological and physical-chemical spoilage, suggesting that microbiological quality alone may overestimate the shelf life of SV cooked salmon.

Optimization of edible coating formulations for improving postharvest quality and shelf life of pear fruit using response surface methodology.

PubMed

Nandane, A S; Dave, Rudri K; Rao, T V Ramana

2017-01-01

The effect of composite edible films containing soy protein isolate (SPI) in combination with additives like hydroxypropyl methylcellulose (HPMC) and olive oil on 'Babughosha' pear ( Pyrus communis L.) stored at ambient temperature (28 ± 5 °C and 60 ± 10% RH) was evaluated using Response surface methodology (RSM). A total of 30 edible coating formulations comprising of SPI (2-6%, w/v), olive oil (0.7-1.1%, v/v), HPMC (0.1-0.5%, w/v) and potassium sorbate (0-0.4% w/v) were evaluated for optimizing the most suitable combination. Quality parameters like weight loss%, TSS, pH and titrable acidity of the stored pears were selected as response variables for optimization. The optimization procedure was carried out using RSM. It was observed that the response variables were mainly effected by concentration of SPI and olive oil in the formulation. Edible coating comprising of SPI 5%, HPMC 0.40%, olive oil 1% and potassium sorbate 0.22% was found to be most suitable combination for pear fruit with predicted values of response variables indicated as weight loss% 3.50, pH 3.41, TSS 11.13 and TA% 0.513.

Selecting broiler chickens for ultimate pH of breast muscle: analysis of divergent selection experiment and phenotypic consequences on meat quality, growth, and body composition traits.

PubMed

Alnahhas, N; Berri, C; Boulay, M; Baéza, E; Jégo, Y; Baumard, Y; Chabault, M; Le Bihan-Duval, E

2014-09-01

Genetic parameters for ultimate pH of pectoralis major muscle (PM-pHu) and sartorius muscle (SART-pHu); color parameters L*, a*, b*; logarithm of drip loss (LogDL) of pectoralis major (PM) muscle; breast meat yield (BMY); thigh and drumstick yield (TY); abdominal fat percentage (AFP); and BW at 6 wk (BW6) were estimated in 2 lines of broiler chickens divergently selected for PM-pHu. Effects of selection on all the previous traits and on glycolytic potential, pectoralis major muscle pH at 15 min postmortem, curing-cooking yield (CCY), cooking loss (CL), and Warner-Bratzler shear force (WBSF) of the PM muscle were also analyzed after 5 generations. Strong genetic determinism of PM-pHu was observed, with estimated h(2) of 0.57 ± 0.02. There was a significant positive genetic correlation (rg) between PM-pHu and SART-pHu (0.54 ± 0.04), indicating that selection had a general rather than a specific effect on energy storage in skeletal muscles. The h(2) estimates of L*, a*, and b* parameters were 0.58 ± 0.02, 0.39 ± 0.02, and 0.48 ± 0.02, respectively. Heritability estimates for TY, BMY, and AFP were 0.39 ± 0.04, 0.52 ± 0.01, and 0.71 ± 0.02, respectively. Our results indicated different genetic control of LogDL and L* of the meat between the 2 lines; these traits had a strong rg with PM-pHu in the line selected for low ultimate pH (pHu) value (pHu-; -0.80 and -0.71, respectively), which was not observed in the line selected for high pHu value (pHu+; -0.04 and -0.29, respectively). A significant positive rg (0.21 ± 0.04) was observed between PM-pHu and BMY but not between PM-pHu and BW6, AFP, or TY. Significant phenotypic differences were observed after 5 generations of selection between the 2 lines. The mean differences (P < 0.001) in pHu between the 2 lines were 0.42 and 0.21 pH units in the breast and thigh muscle, respectively. Breast meat in the pHu+ line exhibited lower L* (-5 units; P < 0.001), a* (-0.22 units; P < 0.001), b* (-1.53 units; P < 0.001), and drip loss (-1.6 units; P < 0.001) than in the pHu- line. Breast meat of the pHu+ line was also characterized by greater CCY (+6.1 units; P < 0.001), lower CL (-1.66 units; P < 0.01), and lower WBSF after cooking (-5.1 units; P < 0.001) compared to the pHu- line. This study highlighted that selection based on pHu can be effective in improving the processing ability of breast meat and reducing the incidence of meat quality defects without affecting chicken growth performance.

Advanced multivariate data analysis to determine the root cause of trisulfide bond formation in a novel antibody-peptide fusion.

PubMed

Goldrick, Stephen; Holmes, William; Bond, Nicholas J; Lewis, Gareth; Kuiper, Marcel; Turner, Richard; Farid, Suzanne S

2017-10-01

Product quality heterogeneities, such as a trisulfide bond (TSB) formation, can be influenced by multiple interacting process parameters. Identifying their root cause is a major challenge in biopharmaceutical production. To address this issue, this paper describes the novel application of advanced multivariate data analysis (MVDA) techniques to identify the process parameters influencing TSB formation in a novel recombinant antibody-peptide fusion expressed in mammalian cell culture. The screening dataset was generated with a high-throughput (HT) micro-bioreactor system (Ambr TM 15) using a design of experiments (DoE) approach. The complex dataset was firstly analyzed through the development of a multiple linear regression model focusing solely on the DoE inputs and identified the temperature, pH and initial nutrient feed day as important process parameters influencing this quality attribute. To further scrutinize the dataset, a partial least squares model was subsequently built incorporating both on-line and off-line process parameters and enabled accurate predictions of the TSB concentration at harvest. Process parameters identified by the models to promote and suppress TSB formation were implemented on five 7 L bioreactors and the resultant TSB concentrations were comparable to the model predictions. This study demonstrates the ability of MVDA to enable predictions of the key performance drivers influencing TSB formation that are valid also upon scale-up. Biotechnol. Bioeng. 2017;114: 2222-2234. © 2017 The Authors. Biotechnology and Bioengineering Published by Wiley Periodicals, Inc. © 2017 The Authors. Biotechnology and Bioengineering Published by Wiley Periodicals, Inc.

Spectroscopic line parameters of NH3 and PH3 in the far infrared

NASA Technical Reports Server (NTRS)

Husson, N.; Goldman, A.; Orton, G.

1982-01-01

NH3 and PH3 rotation and rotation-inversion line parameters in the far to medium IR are calculated for remote sounding purposes of planetary atmospheres; 1607 lines of (N-14)H3, 362 lines of (N-15)H3 and 325 lines of PH3 are compiled. The absolute intensity formulation has been reviewed in the case of rotation and rotation-inversion lines of molecules with C(3v) symmetry. The justification for the general agreement between the authors, and comparisons with other published expressions are given.

Characteristics of aerosol acidity in Hong Kong

NASA Astrophysics Data System (ADS)

Pathak, Ravi Kant; Louie, Peter K. K.; Chan, Chak K.

The ammonium-to-sulfate ratio ([NH 4+]/[SO 42-]) and the strong acidity have been generally used as parameters to describe the acidic nature of atmospheric aerosols. However, both parameters do not provide the in situ acidic characteristics of atmospheric aerosols, which are more relevant to the reactivity and the environmental impacts of the aerosols. In this study, the in situ free acid concentrations and the in situ pH of aerosols are investigated to understand the acidic characteristics of atmospheric aerosols in Hong Kong (HK). Over 182 datasets on 24 h Respirable Suspended Particles (RSP) samples collected in 2001 from seven air-quality-monitoring sites run by the Hong Kong Environmental Protection Department are analyzed. Simulations using the Aerosol Inorganic Model (AIM2) reveal that the in situ acidity, i.e., the free acid concentration ([H +] free), is only a minor fraction (˜23%) of the estimated strong acidity in the fine particles because of the presence of bisulfate ions. The acidity characteristics of fine particles are a function of mainly RH and ammonium to sulfate ratio. The in situ free acid concentration, the normalized water content ([H 2O] AIM2/[SO 42-]), and the dissociation of bisulfate to free acid in the aerosols decrease as the [NH 4+]/[SO 42-] ratio increases and the Relative Humidity (RH) decreases. The acidic fine mode particles have average molar [NH 4+]/[SO 42-] ratio of 1.42, strong acidity of 51 nmol m -3, in situ acidity of 11 nmol m -3, and in situ pH of 0.25 on average. Our findings suggest that even the more neutralized ([NH 4+]/[SO 42-] >1.5) particles, such as those found when HK is under the influence of continental air masses from the Chinese mainland, can have high in situ acidity and low pH when the RH is low. This study calls for more investigation of the acidity of aerosols in HK, incorporating the concepts of in situ acidity and pH.

Response surface methodology for predicting quality characteristics of beef patties added with flaxseed and tomato paste.

PubMed

Valenzuela Melendres, M; Camou, J P; Torrentera Olivera, N G; Alvarez Almora, E; González Mendoza, D; Avendaño Reyes, L; González Ríos, H

2014-05-01

Response surface methodology was used to study the effect of flaxseed flour (FS) and tomato paste (TP) addition, from 0 to 10% and 0 to 20% respectively, on beef patty quality characteristics. The assessed quality characteristics were color (L, a, and b), pH and texture profile analysis (TPA). Also, sensory analysis was performed for the assessment of color, juiciness, firmness, and general acceptance. FS addition reduced L and a values and decreased weight loss of cooked products (P<0.05). An opposite effect was observed when TP was added (P<0.05). All TPA parameters decreased when percentages of FS and TP were increased in the formulation of beef patties. Furthermore, FS and TP addition adversely affected the sensory characteristics of the cooked product (P<0.05); nevertheless, all sensory characteristics evaluated had an acceptable score (>5.6). Thus FS and TP are ingredients that can be used in beef patty preparation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Climate change impacts on marine water quality: The case study of the Northern Adriatic sea.

PubMed

Rizzi, J; Torresan, S; Critto, A; Zabeo, A; Brigolin, D; Carniel, S; Pastres, R; Marcomini, A

2016-01-30

Climate change is posing additional pressures on coastal ecosystems due to variations in water biogeochemical and physico-chemical parameters (e.g., pH, salinity) leading to aquatic ecosystem degradation. With the main aim of analyzing the potential impacts of climate change on marine water quality, a Regional Risk Assessment methodology was developed and applied to coastal marine waters of the North Adriatic. It integrates the outputs of regional biogeochemical and physico-chemical models considering future climate change scenarios (i.e., years 2070 and 2100) with site-specific environmental and socio-economic indicators. Results showed that salinity and temperature will be the main drivers of changes, together with macronutrients, especially in the area of the Po' river delta. The final outputs are exposure, susceptibility and risk maps supporting the communication of the potential consequences of climate change on water quality to decision makers and stakeholders and provide a basis for the definition of adaptation and management strategies. Copyright © 2015 Elsevier Ltd. All rights reserved.

Water-quality and lake-stage data for Wisconsin lakes, water year 1996

USGS Publications Warehouse

,

1997-01-01

The purpose of this report is to provide information about the physical and chemical characteristics of Wisconsin lakes. Data that have been collected at specific lakes, and information to aid in the interpretation of those data, are included in this report. Data collected includes measurements of lake stage and in-lake water quality. Graphs of Secchi depths, surface totalphosphorus and chlorophyll-a concentrations versus time are included for lakes with two or more years of data. Graphs of vertical profiles of temperature, dissolved oxygen, pH, and specific conductance are included for sites where these parameters were measured. Descriptive information for each lake includes: location of the lake, drainage area of the lake's watershed, period for which data are available, revisions to previously published records, and pertinent remarks. Additional data, such as streamflow and water quality in tributary and outlet streams of some of the lakes, are published in another volume: "Water Resources Data-Wisconsin, 1996."

Can green roof act as a sink for contaminants? A methodological study to evaluate runoff quality from green roofs.

PubMed

Vijayaraghavan, K; Joshi, Umid Man

2014-11-01

The present study examines whether green roofs act as a sink or source of contaminants based on various physico-chemical parameters (pH, conductivity and total dissolved solids) and metals (Na, K, Ca, Mg, Al, Fe, Cr, Cu, Ni, Zn, Cd and Pb). The performance of green roof substrate prepared using perlite, vermiculite, sand, crushed brick, and coco-peat, was compared with local garden soil based on improvement of runoff quality. Portulaca grandiflora was used as green roof vegetation. Four different green roof configurations, with vegetated and non-vegetated systems, were examined for several artificial rain events (un-spiked and metal-spiked). In general, the vegetated green roof assemblies generated better-quality runoff with less conductivity and total metal ion concentration compared to un-vegetated assemblies. Of the different green roof configurations examined, P. grandiflora planted on green roof substrate acted as sink for various metals and showed the potential to generate better runoff. Copyright © 2014 Elsevier Ltd. All rights reserved.

Water-quality and lake-stage data for Wisconsin lakes, water year 2005

USGS Publications Warehouse

Rose, W.J.; Garn, H.S.; Goddard, G.L.; Marsh, S.B.; Olson, D.L.; Robertson, Dale M.

2006-01-01

The U.S. Geological Survey (USGS), in cooperation with local and other agencies, collects data at selected lakes throughout Wisconsin. These data, accumulated over many years, provide a data base for developing an improved understanding of the water quality of lakes. The purpose of this report is to provide information about the chemical and physical charac-teristics of Wisconsin lakes. Data that have been collected at specific lakes, and information to aid in the interpretation of those data, are included in this report. Data collected include measure-ments of in-lake water quality and lake stage. Time series graphs of Secchi depths, surface total phosphorus and chlorophyll a concentrations collected during non-frozen periods are included for all lakes. Graphs of vertical profiles of temperature, dissolved oxygen, pH, and specific conductance are included for sites where these parameters were measured. Descriptive infor-mation for each lake includes: location of the lake, area of the lake's watershed, period for which data are available, revisions to previously published records, and pertinent remarks.

Waste treatment and biogas quality in small-scale agricultural digesters.

PubMed

Lansing, Stephanie; Botero, Raúl Botero; Martin, Jay F

2008-09-01

Seven low-cost digesters in Costa Rica were studied to determine the potential of these systems to treat animal wastewater and produce renewable energy. The effluent water has a significantly lower oxygen demand (COD decreased from 2,968 mg/L to 472 mg/L) and higher dissolved nutrient concentration (NH(4)-N increased by 78.3% to 82.2mg/L) than the influent water, which increases the usefulness of the effluent as an organic fertilizer and decreases its organic loading on surface waters. On average, methane constituted 66% of the produced biogas, which is consistent with industrial digesters. Through principle component analysis, COD, turbidity, NH(4)-N, TKN, and pH were determined to be the most useful parameters to characterize wastewater. The results suggest that the systems have the ability to withstand fluctuations in the influent water quality. This study revealed that small-scale agricultural digesters can produce methane at concentrations useful for cooking, while improving the quality of the livestock wastewater.

Water-Chemistry and Its Utility Systems in CCP Power Units (Review)

NASA Astrophysics Data System (ADS)

Larin, B. M.

2018-01-01

Damageability of heat transfer surfaces of waste heat recovery steam generators (HRSG) of combined- cycle plants (CCP) can be reduced due to an increase in the quality of make-up and feed water, the use of phosphate-alkaline or amino compound water chemistry (WC), and improved chemical quality control of the heat carrier and make-up water preparation techniques. Temporary quality standards for the heat medium developed by the All-Russia Thermal Engineering institute (VTI) for CCP power units are presented in comparison with the IAPWS standards; preferences for the choice of a WC type for some power units commissioned in Russia in the first decade of this century are shown; and operational data on the quality of feed, boiler water, and steam for two large CCP-450 and CCP-425 power units are given. The state and prospects for the development of chemical-technological monitoring systems and CCP water treatment plants are noted. Estimability of some CCP diagnostic parameters by measuring specific electric conductivity and pH is shown. An extensive bibliography on this topic is given.

Effect on Quality Characteristics of Tomatoes Grown Under Well-Watered and Drought Stress Conditions.

PubMed

Klunklin, Warinporn; Savage, Geoffrey

2017-07-25

Tomatoes are one of the most nutritionally and economically important crops in New Zealand and around the world. Tomatoes require large amounts of water to grow well and are adversely affected by drought stress. However, few studies have evaluated the physicochemical characteristics of commercial tomatoes grown under water stress conditions. Four tomato cultivars (Incas, Marmande, Scoresby Dwarf, and Window Box Red) were grown in a greenhouse under well-watered and drought stress conditions and the tomatoes were harvested when ripe. The physicochemical properties and antioxidant contents of the fruits were compared. There were significant differences between cultivars in quality characteristics-such as dry matter, total soluble solids, and pH parameters-but there were no differences in the quality characteristics between the two treatments of the fruits ( p > 0.05); however, there were significant differences ( p < 0.05) in the antioxidant compositions (lycopene, total phenolics, and flavonoids) and antioxidant activities (DPPH and ABTS) of the fruits of both cultivars and treatments. Overall, these results indicated that tomatoes increased their bioactive compounds without changing any quality characteristics when exposed to water stress conditions.

Effect of pH on the survival of Listeria innocua in calcium ascorbate solutions and on quality of fresh-cut apples.

PubMed

Karaibrahimoglu, Yildiz; Fan, Xuetong; Sapers, Gerald M; Sokorai, Kimberly

2004-04-01

Fresh-cut apple slices were dipped in calcium ascorbate (CaA) solution at pH values ranging from 2.5 to 7.0 to inhibit browning. After treatment, the cut apples were stored at 4 and 10 degrees C for up to 21 days. Color and texture of the apples were determined on days 1, 14, and 21. In a separate experiement, the pH of CaA solution was adjusted with acetic acid to six different pH levels, and the solution was inoculated with Listeria innocua. The survival of the bacterium and the stability of CaA were determined at 0, 20, and 96 h. The cut apples maintained fresh quality when the pH of the CaA solution was above 4.5, but slight discoloration of apple slices dipped in pH 4.5 solution was observed after 14 days at 10 degrees C. At pH 5.0, the CaA dip maintained the quality of the apples at both temperatures for at least 21 days. The L. innocua population was reduced by 4 to 5 log CFU/ml at pH 4.5 after 96 h. At pH 5, the bacterial population in the CaA solution was reduced by approximately 2 log CFU/ml during the same period. The CaA solution was stable at pH 5 for at least 96 h. Reduction of the pH to between 4.5 and 5.0 might reduce the risk of foodborne illness due to consumption of fresh-cut apples treated with a CaA solution contaminated with Listeria.

Trend analysis of a tropical urban river water quality in Malaysia.

PubMed

Othman, Faridah; M E, Alaa Eldin; Mohamed, Ibrahim

2012-12-01

Rivers play a significant role in providing water resources for human and ecosystem survival and health. Hence, river water quality is an important parameter that must be preserved and monitored. As the state of Selangor and the city of Kuala Lumpur, Malaysia, are undergoing tremendous development, the river is subjected to pollution from point and non-point sources. The water quality of the Klang River basin, one of the most densely populated areas within the region, is significantly degraded due to human activities as well as urbanization. Evaluation of the overall river water quality status is normally represented by a water quality index (WQI), which consists of six parameters, namely dissolved oxygen, biochemical oxygen demand, chemical oxygen demand, suspended solids, ammoniacal nitrogen and pH. The objectives of this study are to assess the water quality status for this tropical, urban river and to establish the WQI trend. Using monthly WQI data from 1997 to 2007, time series were plotted and trend analysis was performed by employing the first-order autocorrelated trend model on the moving average values for every station. The initial and final values of either the moving average or the trend model were used as the estimates of the initial and final WQI at the stations. It was found that Klang River water quality has shown some improvement between 1997 and 2007. Water quality remains good in the upper stream area, which provides vital water sources for water treatment plants in the Klang valley. Meanwhile, the water quality has also improved in other stations. Results of the current study suggest that the present policy on managing river quality in the Klang River has produced encouraging results; the policy should, however, be further improved alongside more vigorous monitoring of pollution discharge from various point sources such as industrial wastewater, municipal sewers, wet markets, sand mining and landfills, as well as non-point sources such as agricultural or urban runoff and commercial activity.

Multi-Response Optimization of Process Parameters for Imidacloprid Removal by Reverse Osmosis Using Taguchi Design.

PubMed

Genç, Nevim; Doğan, Esra Can; Narcı, Ali Oğuzhan; Bican, Emine

2017-05-01

  In this study, a multi-response optimization method using Taguchi's robust design approach is proposed for imidacloprid removal by reverse osmosis. Tests were conducted with different membrane type (BW30, LFC-3, CPA-3), transmembrane pressure (TMP = 20, 25, 30 bar), volume reduction factor (VRF = 2, 3, 4), and pH (3, 7, 11). Quality and quantity of permeate are optimized with the multi-response characteristics of the total dissolved solid (TDS), conductivity, imidacloprid, and total organic carbon (TOC) rejection ratios and flux of permeate. The optimized conditions were determined as membrane type of BW30, TMP 30 bar, VRF 3, and pH 11. Under these conditions, TDS, conductivity, imidacloprid, and TOC rejections and permeate flux were 97.50 97.41, 97.80, 98.00% and 30.60 L/m2·h, respectively. Membrane type was obtained as the most effective factor; its contribution is 64%. The difference between the predicted and observed value of multi-response signal/noise (MRSN) is within the confidence interval.

Pharmacological MRI (phMRI) of the Human Central Nervous System.

PubMed

Lanfermann, H; Schindler, C; Jordan, J; Krug, N; Raab, P

2015-10-01

Pharmacological magnetic resonance imaging (phMRI) of the central nervous system (CNS) addresses the increasing demands in the biopharma industry for new methods that can accurately predict, as early as possible, whether novel CNS agents will be effective and safe. Imaging of physiological and molecular-level function can provide a more direct measure of a drug mechanism of action, enabling more predictive measures of drug activity. The availability of phMRI of the nervous system within the professional infrastructure of the Clinical Research Center (CRC) Hannover as proof of concept center ensures that advances in basic science progress swiftly into benefits for patients. Advanced standardized MRI techniques including quantitative MRI, kurtosis determination, functional MRI, and spectroscopic imaging of the entire brain are necessary for phMRI. As a result, MR scanners will evolve into high-precision measuring instruments for assessment of desirable and undesirable effects of drugs as the basic precondition for individually tailored therapy. The CRC's Imaging Unit with high-end large-scale equipment will allow the following unique opportunities: for example, identification of MR-based biomarkers to assess the effect of drugs (surrogate parameters), establishment of normal levels and reference ranges for MRI-based biomarkers, evaluation of the most relevant MRI sequences for drug monitoring in outpatient care. Another very important prerequisite for phMRI is the MHH Core Facility as the scientific and operational study unit of the CRC partner Hannover Medical School. This unit is responsible for the study coordination, conduction, complete study logistics, administration, and application of the quality assurance system based on required industry standards.

Characterizing potential water quality impacts from soils treated with dust suppressants.

PubMed

Beighley, R Edward; He, Yiping; Valdes, Julio R

2009-01-01

Two separate laboratory experiment series, surface runoff and steady-state seepage, were performed to determine if dust suppressant products can be applied to soils with an expected minimal to no negative impact on water quality. The experiments were designed to mimic arid field conditions and used two soils (clayey and sandy) and six different dust suppressants. The two experiments consisted of: (i) simulated rainfall (intensities of 18, 33, or 61 mm h(-1)) and associated runoff from soil trays at a surface slope of 33%; and (ii) steady-state, constant head seepage through soil columns. Both experiment series involved two product application scenarios and three application ages (i.e., to account for degradation effects) for a total of 126 surface runoff and 80 column experiments. One composite effluent sample was collected from each experiment and analyzed for pH, electrical conductivity, total suspended solids (TSS), total dissolved solids, dissolved oxygen, total organic carbon, nitrate, nitrite, and phosphate. Paired t tests at 1 and 5% levels of significance and project specific data quality objectives are used to compare water quality parameters from treated and untreated soils. Overall, the results from this laboratory scale study suggest that the studied dust suppressants have minimal potential for adverse impacts to selected water quality parameters. The primary impacts were increased TSS for two synthetic products from the surface runoff experiments on both soils. The increase in TSS was not expected based on previous studies and may be attributed to this study's focus on simulating real-world soil agitation/movement at an active construction site subjected to rough grading.

A Two-Level Structural Equation Model for Evaluating the External Effectiveness of PhD

ERIC Educational Resources Information Center

Chiandotto, Bruno; Masserini, Lucio

2011-01-01

In recent years the number of PhDs in Italy has significantly grown and purposes of PhD courses have expanded from the traditional ones. The analysis of the contribution of PhD title for job placement and employment condition of PhDs is an important tool for evaluating the quality and the effectiveness of PhD courses. For this reason, knowledge of…

Exercise Physiology and Pulmonary Hemodynamic Abnormality in PH Patients with Exercise Induced Venous-To-Systemic Shunt.

PubMed

Guo, Jian; Shi, Xue; Yang, Wenlan; Gong, Sugang; Zhao, Qinhua; Wang, Lan; He, Jing; Shi, Xiaofang; Sun, Xingguo; Liu, Jinming

2014-01-01

To identify the pulmonary hypertension (PH) patients who develop an exercise induced venous-to-systemic shunt (EIS) by performing the cardiopulmonary exercise test (CPET), analyse the changes of CPET measurements during exercise and compare the exercise physiology and resting pulmonary hemodynamics between shunt-PH and no-shunt-PH patients. Retrospectively, resting pulmonary function test (PFT), right heart catheterization (RHC), and CPET for clinical evaluation of 104 PH patients were studied. Considering all 104 PH patients by three investigators, 37 were early EIS+, 61 were EIS-, 3 were late EIS+, and 3 others were placed in the discordant group. PeakVO2, AT and OUES were all reduced in the shunt-PH patients compared with the no-shunt-PH subjects, whereas VE/VCO2 slope and the lowest VE/VCO2 increased. Besides, the changes and the response characteristics of the key CPET parameters at the beginning of exercise in the shunt group were notably different from those of the no shunt one. At cardiac catheterization, the shunt patients had significantly increased mean pulmonary artery pressure (mPAP), mean right atrial pressure (mRAP) and pulmonary vascular resistance (PVR), reduced cardiac output (CO) and cardiac index (CI) compared with the no shunt ones (P<0.05). Resting CO was significantly correlated with exercise parameters of AT (r = 0.527, P<0.001), OUES (r = 0.410, P<0.001) and Peak VO2 (r = 0.405, P<0.001). PVR was significantly, but weakly, correlated with the above mentioned CPET parameters. CPET may allow a non-invasive method for detecting an EIS and assessing the severity of the disease in PH patients.

Reduced Salinity Improves Marine Food Availability With Positive Feedbacks on pH in a Tidally-Dominated Estuary

NASA Astrophysics Data System (ADS)

Lowe, A. T.; Roberts, E. A.; Galloway, A. W. E.

2016-02-01

Coastal regions around the world are changing rapidly, generating many physiological stressors for marine organisms. Food availability, a major factor determining physiological condition of marine organisms, in these systems reflects the influence of biological and environmental factors, and will likely respond dramatically to long-term changes. Using observations of phytoplankton, detritus, and their corresponding fatty acids and stable isotopes of carbon, nitrogen and sulfur, we identified environmental drivers of pelagic food availability and quality along a salinity gradient in a large tidally influenced estuary (San Juan Archipelago, Salish Sea, USA). Variation in chlorophyll a (Chl a), biomarkers and environmental conditions exhibited a similar range at both tidal and seasonal scales, highlighting a tide-related mechanism controlling productivity that is important to consider for long-term monitoring. Multiple parameters of food availability were inversely and non-linearly correlated to salinity, such that availability of high-quality (based on abundance, essential fatty acid concentration and C:N) seston increased below a salinity threshold of 30. The increased marine productivity was associated with increased pH and dissolved oxygen (DO) at lower salinity. Based on this observation we predicted that a decrease of salinity to below the threshold would result in higher Chl a, temperature, DO and pH across a range of temporal and spatial scales, and tested the prediction with a meta-analysis of available data. At all scales, these variables showed significant and consistent increases related to the salinity threshold. This finding provides important context to the increased frequency of below-threshold salinity over the last 71 years in this region, suggesting greater food availability with positive feedbacks on DO and pH. Together, these findings indicate that many of the environmental factors predicted to increase physiological stress to benthic suspension feeders (e.g. decreased salinity) may simultaneously and paradoxically improve conditions for benthic organisms.

The effects of different chilling methods on meat quality and calpain activity of pork muscle longissimus dorsi.

PubMed

Xu, Yang; Huang, Ji-Chao; Huang, Ming; Xu, Bao-Cai; Zhou, Guang-Hong

2012-01-01

The objective of this study was to investigate the effects of conventional chilling (0 to 4 °C), rapid chilling (RC, -20 °C for 30 min, followed by 0 to 4 °C), and short-duration chilling (0 to 4 °C for 30 min, followed by 25 °C) on meat quality and calpain activity of pork muscle longissimus dorsi (LD). The muscle quality characteristics pH, color, cooking loss, pressing loss and tenderness, and calpain activities were measured 0-, 3-, 12-, and 24-h postmortem. Results show that the RC resulted in a faster temperature decline of the muscle, and prevented the meat pH and Commission Internationale de l'Eclairage L* value from declining during postmortem aging. RC also reduced meat cooking loss and pressing loss compared with the other two chilling methods. However, the chilling methods did not significantly affect meat shear force. During the first 24-h postmortem, there was not a noticeable change in the activity of m-calpain. But μ-calpain activity decreased regardless of chilling method. In the rapidly chilled carcasses, μ-calpain activity remained the same 3- and 12-h postmortem. However, in the short-duration chilled and conventionally chilled carcasses, the activity was visibly reduced. At 24-h postmortem, no clear zones on the gel were observed in all three treatments. Conventional and RC methods are commonly used for pork in commercial practice nowadays. Compared with conventional chilling, the effect of RC on quality parameters of pork varies. In recent years, short-duration chilling (SC) is widely used in many Chinese pig slaughtering facilities. However, few researchers have studied the effect of SD on pork quality. Therefore, the present study investigated the effect of different chilling methods on functionalities or quality of chilled pork meat. © 2011 Institute of Food Technologists®

Rested and stressed farmed Atlantic cod (Gadus morhua) chilled in ice or slurry and effects on quality.

PubMed

Digre, Hanne; Erikson, Ulf; Aursand, Ida G; Gallart-Jornet, Lorena; Misimi, Ekrem; Rustad, Turid

2011-01-01

The main objectives of this study were to investigate (1) whether rested harvest of farmed cod was better maintained by chilling with slurry rather than by traditional ice storage, (2) whether chilling with slurry would be a feasible chilling method to assure low core temperatures (≤0 °C) at packing of gutted fish, and (3) the effects of superchilling compared with traditional ice on selected quality parameters of cod during storage. In the experiment, seawater slurry at -2.0 ± 0.3 °C was used. Anesthetized (AQUI-S™), percussion stunned, and stressed cod chilled in slurry were compared. Cod stored on ice were used as reference group. The fish were evaluated at the day of slaughter, and after 7 and 14 d of storage according to handling stress (initial muscle pH, muscle twitches, rigor mortis), core temperatures, quality index method, microbial counts, weight changes, salt and water content, water distribution, pH, adenosine triphosphate-degradation products, K-value, water-holding capacity, fillet color, and texture. Chilling cod in slurry was more rapid than chilling in ice. Prechilling (1 d) of cod in slurry before subsequent ice storage resulted in lower quality 7 d postmortem compared with both ice and continuous slurry storage. The potential advantages of superchilling became more prominent after 14 d with lower microbiological activity, better maintenance of freshness (lower total quality index scores and lower K-values) compared with fish stored on ice. A drawback with slurry-stored fish was that cloudy eyes developed earlier, in addition to weight gain and salt uptake compared to ice-stored fish. Practical Application: Chilling is an essential operation in any fish-processing plant. This manuscript addresses different applications of slurry ice in the processing and storage of Atlantic cod. Cod quality was assessed after 7 and 14 d of iced and superchilled storage.

Water for human and livestock consumption in rural settings of Ethiopia: assessments of quality and health aspects.

PubMed

Amenu, Kebede; Markemann, André; Valle Zárate, Anne

2013-11-01

The study aimed to assess the quality and health aspects of water intended for human and livestock consumption in two rural districts of the Rift Valley of Ethiopia. The study involved two parts: the first consisted of a questionnaire survey and farmers' group discussions, complemented by secondary health data, and the second part determined the chemical (total dissolved solids, pH, manganese, hexa-valent chromium, fluoride) and microbiological quality of different water sources during dry and wet seasons. The result showed a lack of sustainable access to safe water in the communities. Industrial pollution and mismanagement of water sources by human and livestock was found to be a source of potential health risk. Potentially linked human health problems like malaria, diarrhoea and gastrointestinal parasites were common in the districts. Overall, 76% of the assessed water sources (n = 25) failed to comply with World Health Organization guidelines for human drinking water, for at least one assessed parameter, mostly irrespective of the season. The non-compliance was mainly attributed to Escherichia coli contamination and/or high fluoride concentration. At least 20% of the water samples were also found to be unfit for livestock consumption based on assessed chemical parameters in both dry and wet seasons. To minimize the health risk associated with mismanagement and poor quality of water sources in the area, targeted action in the protection of surface water sources should be given priority.

Drinking water quality assessment in Southern Sindh (Pakistan).

PubMed

Memon, Mehrunisa; Soomro, Mohammed Saleh; Akhtar, Mohammad Saleem; Memon, Kazi Suleman

2011-06-01

The southern Sindh province of Pakistan adjoins the Arabian Sea coast where drinking water quality is deteriorating due to dumping of industrial and urban waste and use of agrochemicals and yet has limited fresh water resources. The study assessed the drinking water quality of canal, shallow pumps, dug wells, and water supply schemes from the administrative districts of Thatta, Badin, and Thar by measuring physical, chemical, and biological (total coliform) quality parameters. All four water bodies (dug wells, shallow pumps canal water, and water supply schemes) exceeded WHO MPL for turbidity (24%, 28%, 96%, 69%), coliform (96%, 77%, 92%, 81%), and electrical conductivity (100%, 99%, 44%, 63%), respectively. However, the turbidity was lower in underground water, i.e., 24% and 28% in dug wells and shallow pumps as compared to open water, i.e., 96% and 69% in canal and water supply schemes, respectively. In dug wells and shallow pumps, limits for TDS, alkalinity, hardness, and sodium exceeded, respectively, by 63% and 33%; 59% and 70%, 40% and 27%, and 78% and 26%. Sodium was major problem in dug wells and shallow pumps of district Thar and considerable percent in shallow pumps of Badin. Iron was major problem in all water bodies of district Badin ranging from 50% to 69% and to some extent in open waters of Thatta. Other parameters as pH, copper, manganese, zinc, and phosphorus were within standard permissible limits of World Health Organization. Some common diseases found in the study area were gastroenteritis, diarrhea and vomiting, kidney, and skin problems.

Anthropogenic activities impact on atmospheric environmental quality in a gas-flaring community: application of fuzzy logic modelling concept.

PubMed

Akintola, Olayiwola Akin; Sangodoyin, Abimbola Yisau; Agunbiade, Foluso Oyedotun

2018-05-24

We present a modelling concept for evaluating the impacts of anthropogenic activities suspected to be from gas flaring on the quality of the atmosphere using domestic roof-harvested rainwater (DRHRW) as indicator. We analysed seven metals (Cu, Cd, Pb, Zn, Fe, Ca, and Mg) and six water quality parameters (acidity, PO 4 3- , SO 4 2- , NO 3 - , Cl - , and pH). These were used as input parameters in 12 sampling points from gas-flaring environments (Port Harcourt, Nigeria) using Ibadan as reference. We formulated the results of these input parameters into membership function fuzzy matrices based on four degrees of impact: extremely high, high, medium, and low, using regulatory limits as criteria. We generated indices that classified the degree of anthropogenic activity impact on the sites from the product membership function matrices and weight matrices, with investigated (gas-flaring) environment as between medium and high impact compared to those from reference (residential) environment that was classified as between low and medium impact. Major contaminants of concern found in the harvested rainwater were Pb and Cd. There is also the urgent need to stop gas-flaring activities in Port Harcourt area in particular and Niger Delta region of Nigeria in general, so as to minimise the untold health hazard that people living in the area are currently faced with. The fuzzy methodology presented has also indicated that the water cannot safely support potable uses and should not be consumed without purification due to the impact of anthropogenic activities in the area but may be useful for other domestic purposes.

Development of a water quality index (WQI) for the Loktak Lake in India

NASA Astrophysics Data System (ADS)

Das Kangabam, Rajiv; Bhoominathan, Sarojini Devi; Kanagaraj, Suganthi; Govindaraju, Munisamy

2017-10-01

The present work was carried out to assess a water quality index (WQI) of the Loktak Lake, an important wetland which has been under pressure due to the increasing anthropogenic activities. Physicochemical parameters like temperature (Tem), potential hydrogen (pH), electrical conductivity (EC), turbidity (T), dissolved oxygen (DO), total hardness (TH), calcium (Ca), chloride (Cl), fluoride (F), sulphate ({SO}4^{2-}), magnesium (Mg), phosphate ({PO}4^{3-}), sodium (Na), potassium (K), nitrite (NO2), nitrate (NO3), total dissolved solids (TDS), total carbon (TC), biochemical oxygen demand (BOD), and chemical oxygen demand (COD) were analyzed using standard procedures. The values obtained were compared with the guidelines for drinking purpose suggested by the World Health Organization and Bureau of Indian Standard. The result shows the higher concentration of nitrite in all the location which is beyond the permissible limit. Eleven parameters were selected to derive the WQI for the estimation of water potential for five sampling sites. A relative weight was assigned to each parameter range from 1.46 to 4.09 based on its importance. The WQI values range from 64 to 77 indicating that the Loktak Lake water is not fit for drinking, including both human and animals, even though the people living inside the Lake are using it for drinking purposes. The implementation of WQI is necessary for proper management of the Loktak Lake and it will be a very helpful tool for the public and decision makers to evaluate the water quality of the Loktak Lake for sustainable management.

Drinking water quality in six small tea gardens of Sonitpur District of Assam, India, with special reference to heavy metals.

PubMed

Dutta, Joydev; Chetia, Mridul; Misra, A K

2011-10-01

Contamination of drinking water by arsenic and other heavy metals and their related toxicology is a serious concern now-a-days. Millions of individual world-wide are suffering from the arsenic and other heavy metal related diseases due to the consumption of contaminated groundwater. 60 water samples from different sources of 6 small tea gardens of Sonitpur district were collected to study the potability of water for drinking purposes. The water samples collected from sources like tube wells, ring wells and ponds were analyzed for arsenic, heavy metals like iron, manganese and mercury with sodium, potassium, calcium, magnesium, pH, total hardness, chloride, fluoride and sulphate. Some drain water samples of the tea garden areas were also collected to analyze the above mentioned water parameters to see the contamination level. Experiments revealed that 78% samples of total collection had arsenic content above the permissible limit (0.01 ppm) of WHO guideline value for drinking water. The highest arsenic was observed 0.09 ppm at one sample of Gobindra Dahal tea garden of Gohpur sub division of Sonitpur district. 94% samples had contamination due to manganese 39% samples had iron and 44% samples had Hg. The water quality data was subjected to some statistical treatments like NDA, cluster analysis and pearson correlation to observe the distribution pattern of the different water quality parameters. A strong pearson correlation coefficient was observed between parameters-arsenic and manganese (0.865) and arsenic and mercury (0.837) at 0.01 level, indicated the same sources of drinking water contamination.

An Overall Water Quality Index (WQI) for a Man-Made Aquatic Reservoir in Mexico

PubMed Central

Rubio-Arias, Hector; Contreras-Caraveo, Manuel; Quintana, Rey Manuel; Saucedo-Teran, Ruben Alfonso; Pinales-Munguia, Adan

2012-01-01

A Water Quality Index (WQI) is a useful statistical tool for simplifying, reporting and interpreting complex information obtained from any body of water. A simple number given by any WQI model explains the level of water contamination. The objective was to develop a WQI for the water of the Luis L. Leon dam located in the state of Chihuahua, Mexico. Monthly water samples were obtained in 2009; January 10, February 12, March 8, May 20, June 10, July 9, August 12, September 10, October 11, November 15 and December 13. Ten sampling sites were randomly selected after dividing the study area using a geographic package. In each site, two samples at the top depth of 0.20 m and 1.0 m were obtained to quantify physical-chemical parameters. The following 11 parameters were considered to calculate the WQI; pH, Electrical Conductivity (EC), Dissolved Oxygen (DO), color, turbidity, ammonia nitrogen, fluorides, chlorides, sulfates, Total Solids (TS) and phosphorous (P). The data analysis involved two steps; a single analysis for each parameter and the WQI calculation. The resulted WQI value classified the water quality according to the following ranges: <2.3 poor water; from 2.3 to 2.8 good water; and >2.8 excellent water. The results showed that the WQI values changed from low levels (WQI < 2.3) in some points during autumn time to high levels (WQI > 2.8) most of the year and the variation was due to time of sampling generally rainy season. PMID:22754466

Modeling of salt and pH gradient elution in ion-exchange chromatography.

PubMed

Schmidt, Michael; Hafner, Mathias; Frech, Christian

2014-01-01

The separation of proteins by internally and externally generated pH gradients in chromatofocusing on ion-exchange columns is a well-established analytical method with a large number of applications. In this work, a stoichiometric displacement model was used to describe the retention behavior of lysozyme on SP Sepharose FF and a monoclonal antibody on Fractogel SO3 (S) in linear salt and pH gradient elution. The pH dependence of the binding charge B in the linear gradient elution model is introduced using a protein net charge model, while the pH dependence of the equilibrium constant is based on a thermodynamic approach. The model parameter and pH dependences are calculated from linear salt gradient elutions at different pH values as well as from linear pH gradient elutions at different fixed salt concentrations. The application of the model for the well-characterized protein lysozyme resulted in almost identical model parameters based on either linear salt or pH gradient elution data. For the antibody, only the approach based on linear pH gradients is feasible because of the limited pH range useful for salt gradient elution. The application of the model for the separation of an acid variant of the antibody from the major monomeric form is discussed. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Non-invasive technique to measure biogeochemical parameters (pH and O2) in a microenvironment: Design and applications

NASA Astrophysics Data System (ADS)

Li, Biting; Seliman, Ayman; Pales, Ashley; Liang, Weizhen; Sams, Allison; Darnault, Christophe; Devol, Timothy

2017-04-01

The primary objectives of this research are to do the pH and O2 sensor foils calibration and then to test them in applications. Potentially, this project can be utilized to monitor the fate and transport of radionuclides in porous media. The information for physical and chemical parameters (e.g. pH and O2) is crucial to know when determining contaminants' behavior and transport in the environment. As a non-invasive method, optical imaging technique using a DSLR camera could capture data on the foil when it fluoresces, and gives a high temporal and spatial resolution during the experimental period. The calibration procedures were done in cuvettes in a row. The preliminary experiments could measure pH value in the range from 4.5 to 7.5, and O2 concentration from 0 mg/L to 20.74 mg/L. Applications of sensor foils have involved nano zero valent and acid rain experiments in order to obtain a gradient of parameter changes.

Standardization and quality control parameters for Muktā Bhasma (calcined pearl)

PubMed Central

Joshi, Namrata; Sharma, Khemchand; Peter, Hema; Dash, Manoj Kumar

2015-01-01

Background: Muktā Bhasma (MB) is a traditional Ayurvedic preparation for cough, breathlessness, and eye disorders and is a powerful cardiac tonic, mood elevator, and known to promote strength, intellect, and semen production. Objectives: The present research work was conducted to generate fingerprint for raw and processed MB for quality assessment and standardization using classical and other techniques. Setting and Design: Three samples of MB were prepared by purification (śodhana) of Muktā (pearl) followed by repeated calcinations (Māraṇa). Resultant product was subjected to organoleptic tests and Ayurvedic tests for quality control such as rekhāpūrṇatā, vāritaratva, and nirdhūmatva. Materials and Methods: For quality control, physicochemical parameters such as loss on drying, total ash value, acid insoluble ash, specific gravity, pH value, and other tests using techniques such as elemental analysis with energy dispersive X-ray analysis (EDAX), Structural study with powder X-ray diffraction, particle size with scanning electron microscopy (SEM) were carried out on raw Muktā, Śodhita Muktā, and triplicate batches of MB. Results: The study showed that the raw material Muktā was calcium carbonate in aragonite form, which on repeated calcinations was converted into a more stable calcite form. SEM studies revealed that in raw and purified materials the particles were found scattered and unevenly arranged in the range of 718.7–214.7 nm while in final product, uniformly arranged, stable, rod-shaped, and rounded particles with more agglomerates were observed in the range of 279.2–79.93 nm. EDAX analysis revealed calcium as a major ingredient in MB (average 46.32%) which increased gradually in the stages of processing (raw 34.11%, Śodhita 37.5%). Conclusion: Quality control parameters have been quantified for fingerprinting of MB prepared using a particular method. PMID:26600667

The effect of anthropogenic and natural factors on the prevalence of physicochemical parameters of water and bacterial water quality indicators along the river Białka, southern Poland.

PubMed

Bojarczuk, Anna; Jelonkiewicz, Łukasz; Lenart-Boroń, Anna

2018-04-01

This study was aimed to determine the anthropogenic and natural factors affecting spatial and temporal changes in the physicochemical parameters and bacterial indicators of water quality in the river Białka. The impact of intensive development of the tourist infrastructure on the quality of river water and the potential health threats to tourists was also assessed. Water samples were collected over a period of 2.5 years, once per each month in four sites along the river. Temperature, electrolytic conductivity, pH, and water level were measured onsite; flow rate data were acquired from the Institute of Meteorology and Water Management; chemical analyses allowed to determine the amount of fourteen ions, while microbiological indicators included total and thermotolerant coliforms, total and thermotolerant Escherichia coli, and mesophilic and psychrophilic bacteria. The combination of hydrological, hydrochemical, and microbiological methods generated large amount of data, which were processed by multivariate statistical analysis. A downstream cumulative effect was observed in the contamination of the river water. Fecal coliforms and E. coli were detected in all sites, suggesting the source of fecal contamination even in the protected areas. Intensive development of a ski resort and the related infrastructure, together with the need to accommodate numerous tourists in the examined region, has an evident environmental impact. The resulting deterioration of water quality poses health risks to tourists, as water from the Białka river is used for a variety of purposes, including as a raw drinking water or for artificial snowing of ski slopes. The seasonal changes in the physicochemical parameters mainly result from varying natural factors that shape the water quality in the studied region. The differences in the number of analyzed microorganisms result from seasonal variation in touristic activity and are affected mostly by point sources of sewage inflow.

Two-stage anaerobic digestion of sugar beet silage: The effect of the pH-value on process parameters and process efficiency.

PubMed

Kumanowska, Elzbieta; Uruñuela Saldaña, Mariana; Zielonka, Simon; Oechsner, Hans

2017-12-01

The study investigated the influence of the target pH-values 4.5, 5, 5.5 and 6 in the acidification reactor on process parameters, such as substrate-specific methane yield and the intermediates, in the two-stage anaerobic digestion of sugar beet silage. The total specific methane yield (Nlkg -1 CODd -1 ) increased with an increase in the pH (pH 4.5: 140.58±70.08, pH 5: 181.21±55.71, pH 5.5: 218.32±51.01, pH 6: 256.47±28.78). The pH-value also had an effect on the dominant intermediate in hydrolysate. At the pH-value of 4.5, almost no acidification and microbial activity was observed. At pH 5 and 5.5, butyric acid production dominated, guided by H 2 production. At pH 6 acetic acid was the main product. The absence of H 2 and the highest SMY makes it favorable under practical aspects. Copyright © 2017 Elsevier Ltd. All rights reserved.

Water quality assessment: surface water sources used for drinking and irrigation in Zaria, Nigeria are a public health hazard.

PubMed

Chigor, Vincent N; Umoh, Veronica J; Okuofu, Charles A; Ameh, Joseph B; Igbinosa, Etinosa O; Okoh, Anthony I

2012-05-01

We assessed the quality and pollution status of source surface waters in Zaria, Nigeria by monitoring the nature, cause and extent of pollution in Samaru stream, Kubanni River and Kubanni dam over a period of 10 months, between March and December 2002. A total of 228 water samples was collected from 12 sites and analysed for a total of ten physicochemical and one bacteriological quality indicators, using standard methods. Aesthetic water quality impairment parameters were also observed. The mean values of most water quality parameters were significantly higher (P < 0.05) in both the stream and river than in the dam. There was no significant correlation between faecal coliform counts (FCC) and water temperature (in the range 15-33°C); pH (5.77-7.32); and turbidity (1.4-567 NTU). The high FCC ranged from 2.0 × 10(1) to 1.6 × 10(6) MPN/100 ml and exceeded the WHO standards for drinking water and water used for fresh-produce irrigation, and correlated positively (P < 0.05) with conductivity (in the range 68-1,029 μS/cm); TDS (10.0-70.0 mg/l); TSS (10.0-70.0 mg/l); Cl (7.5-181 mg/l); PO(4)(-) P (0.01-0.41 mg/l); NO(3)(-) N (0.6-3.8 mg/l) and BOD(5) (0.1-14.9 mg/l). The main pollution sources were municipal wastewater, stormwater runoffs, the ABU sewage treatment plant, abattoir effluents and irrigation farms treated with chemical fertilisers. We conclude that these water bodies are potentially hazardous to public health and that proper sewage treatment and river quality monitoring are needed to warn against hazards to public health.