Sample records for quantity sgq concept

  1. PACKAGING CERTIFICATION PROGRAM METHODOLOGY FOR DETERMINING DOSE RATES FOR SMALL GRAM QUANTITIES IN SHIPPING PACKAGINGS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nathan, S.; Loftin, B.; Abramczyk, G.

    The Small Gram Quantity (SGQ) concept is based on the understanding that small amounts of hazardous materials, in this case radioactive materials (RAM), are significantly less hazardous than large amounts of the same materials. This paper describes a methodology designed to estimate an SGQ for several neutron and gamma emitting isotopes that can be shipped in a package compliant with 10 CFR Part 71 external radiation level limits regulations. These regulations require packaging for the shipment of radioactive materials, under both normal and accident conditions, to perform the essential functions of material containment, subcriticality, and maintain external radiation levels withinmore » the specified limits. By placing the contents in a helium leak-tight containment vessel, and limiting the mass to ensure subcriticality, the first two essential functions are readily met. Some isotopes emit sufficiently strong photon radiation that small amounts of material can yield a large dose rate outside the package. Quantifying the dose rate for a proposed content is a challenging issue for the SGQ approach. It is essential to quantify external radiation levels from several common gamma and neutron sources that can be safely placed in a specific packaging, to ensure compliance with federal regulations. The Packaging Certification Program (PCP) Methodology for Determining Dose Rate for Small Gram Quantities in Shipping Packagings provides bounding shielding calculations that define mass limits compliant with 10 CFR 71.47 for a set of proposed SGQ isotopes. The approach is based on energy superposition with dose response calculated for a set of spectral groups for a baseline physical packaging configuration. The methodology includes using the MCNP radiation transport code to evaluate a family of neutron and photon spectral groups using the 9977 shipping package and its associated shielded containers as the base case. This results in a set of multipliers for 'dose per particle

  2. PCP METHODOLOGY FOR DETERMINING DOSE RATES FOR SMALL GRAM QUANTITIES IN SHIPPING PACKAGINGS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nathan, S.

    The Small Gram Quantity (SGQ) concept is based on the understanding that small amounts of hazardous materials, in this case radioactive materials, are significantly less hazardous than large amounts of the same materials. This study describes a methodology designed to estimate an SGQ for several neutron and gamma emitting isotopes that can be shipped in a package compliant with 10 CFR Part 71 external radiation level limits regulations. These regulations require packaging for the shipment of radioactive materials perform, under both normal and accident conditions, the essential functions of material containment, subcriticality, and maintain external radiation levels within regulatory limits.more » 10 CFR 71.33(b)(1)(2)&(3) state radioactive and fissile materials must be identified and their maximum quantity, chemical and physical forms be included in an application. Furthermore, the U.S. Federal Regulations require application contain an evaluation demonstrating the package (i.e., the packaging and its contents) satisfies the external radiation standards for all packages (10 CFR 71.31(2), 71.35(a), & 71.47). By placing the contents in a He leak-tight containment vessel, and limiting the mass to ensure subcriticality, the first two essential functions are readily met. Some isotopes emit sufficiently strong photon radiation that small amounts of material can yield a large external dose rate. Quantifying of the dose rate for a proposed content is a challenging issue for the SGQ approach. It is essential to quantify external radiation levels from several common gamma and neutron sources that can be safely placed in a specific packaging, to ensure compliance with federal regulations. The Packaging Certification Program (PCP) Methodology for Determining Dose Rate for Small Gram Quantities in Shipping Packagings described in this report provides bounding mass limits for a set of proposed SGQ isotopes. Methodology calculations were performed to estimate external

  3. A GREEN'S FUNCTION APPROACH FOR DETERMINING DOSE RATES FOR SMALL GRAM QUANTITIES IN SHIPPING PACKAGINGS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nathan, S.

    The Small Gram Quantity (SGQ) concept is based on the understanding that small amounts of hazardous materials, in this case radioactive materials (RAM), are significantly less hazardous than large amounts of the same materials. This paper describes a methodology designed to estimate an SGQ for several neutron and gamma emitting isotopes that can be shipped in a package in compliance with 10 CFR Part 71 external radiation level limits regulations. The neutron and photon sources were calculated using both ORIGEN-S and RASTA. The response from a unit source in each neutron and photon group was calculated using MCNP5 with eachmore » unshielded and shielded container configuration. Effects of self-shielding on both neutron and photon response were evaluated by including either plutonium oxide or iron in the source region for the case with no shielded container. For the cases of actinides mixed with light elements, beryllium is the bounding light element. The added beryllium (10 to 90 percent of the actinide mass) in the cases studied represents between 9 and 47 percent concentration of the total mixture mass. For beryllium concentrations larger than 50 percent, the increase in the neutron source term and dose rate tend to increase at a much lower rate than at concentrations lower than 50%. The intimately mixed actinide-beryllium form used in these models is very conservative and thus the limits presented in this report are practical bounds on the mass that can be safely shipped. The calculated dose rate from one gram of each isotope was then used to determin the maximum amount of a single isotope that could be shipped in the Model 9977 Package (or packagings having the same or larger external dimensions as well as similar structural materials) and have the external radiation level within the regulatory dose limits at the surface of the package. The estimates of the mass limits presented would also serve as conservative limits for both the Models 9975 and 9978 packages

  4. On the Concepts of Quantity and Quality in the History of Western Thought

    ERIC Educational Resources Information Center

    Campbell, Stephen R.

    2004-01-01

    This paper charts a cognitive history of the concepts of quantity and quality from three inter-related and inter-dependent perspectives of mathematics, logic, and physics. In so doing, other notions associated with the evolution of these concepts are identified and explicated. It is argued that the concepts of quantity and quality, considered in…

  5. Definition of Small Gram Quantity Contents for Type B Radioactive Material Transportation Packages: Activity-Based Content Limitations

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sitaraman, S; Kim, S; Biswas, D

    2010-10-27

    packaging not exceed the regulatory limits prescribed by 10 CFR 71 for non-exclusive shipments. The mass of each radioisotope presented in this paper is limited by the radiation dose rate on the external surface of the package, which per the regulatory limit should not exceed 200 mrem/hr. The results presented are a compendium of allowable masses of a variety of different isotopes (with varying impurity levels of beryllium in some of the actinide isotopes) that, when loaded in an unshielded packaging, do not result in an external dose rate on the surface of the package that exceeds 190 mrem/hr (190 mrem/hr was chosen to provide 5% conservatism relative to the regulatory limit). These mass limits define the term 'Small Gram Quantity' (SGQ) contents in the context of radioactive material transportation packages. The term SGQ is isotope-specific and pertains to contents in radioactive material transportation packages that do not require shielding and still satisfy the external dose rate requirements. Since these calculated mass limits are for contents without shielding, they are conservative for packaging materials that provide some limited shielding or if the contents are placed into a shielded package. The isotopes presented in this paper were chosen as the isotopes that Department of Energy (DOE) sites most likely need to ship. Other more rarely shipped isotopes, along with industrial and medical isotopes, are planned to be included in subsequent extensions of this work.« less

  6. RF Modal Quantity Gaging

    NASA Technical Reports Server (NTRS)

    Vanleuven, K.

    1989-01-01

    The primary objective is to provide a concept of a radio frequency (RF) modal resonance technique which is being investigated as a method for gaging the quantities of subcritical cryogenic propellants in metallic tanks. Of special interest are the potential applications of the technique to microgravity propellant gaging situations. The results of concept testing using cryogenic oxygen, hydrogen, and nitrogen, as well as paraffin simulations of microgravity fluid orientations, are reported. These test results were positive and showed that the gaging concept was viable.

  7. Zero-gravity quantity gaging system

    NASA Technical Reports Server (NTRS)

    1989-01-01

    The Zero-Gravity Quantity Gaging System program is a technology development effort funded by NASA-LeRC and contracted by NASA-JSC to develop and evaluate zero-gravity quantity gaging system concepts suitable for application to large, on-orbit cryogenic oxygen and hydrogen tankage. The contract effective date was 28 May 1985. During performance of the program, 18 potential quantity gaging approaches were investigated for their merit and suitability for gaging two-phase cryogenic oxygen and hydrogen in zero-gravity conditions. These approaches were subjected to a comprehensive trade study and selection process, which found that the RF modal quantity gaging approach was the most suitable for both liquid oxygen and liquid hydrogen applications. This selection was made with NASA-JSC concurrence.

  8. Quantum Physics and Mathematical Debates Concerning the Problem of the Ontological Priority between Continuous Quantity and Discrete Quantity

    NASA Astrophysics Data System (ADS)

    Pin, Victor Gómez

    In his book about the Categories (that is about the ultimate elements of classification and order), in the chapter concerning the quantity (IV, 20) Aristotle says that this concept recovers two kinds of modalities: the discrete quantity and the continuous quantity and he gives as examples the number for the first one; line, surface, solid, times and space for the second one. The main philosophical problem raised by this text is to determine which of the two modalities of the quantity has the ontological priority over the other (given two concepts A and B, we assume that A has ontological priority over B if every entity that possesses the quality B possesses necessarily the quality A). The problem is magnified by the fact that space, which in some part of Aristotle's Physics is mentioned not only as a category properly speaking but even as the main category whose power can be amazing, is in the evoked text of the Categories's Book reduced to expression of the continuum, and sharing this condition with time. In this matter the controversy is constant through the common history of Science and Philosophy.

  9. Radiation quantities and units

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    1980-04-15

    This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. In line, with providing more didactic material and useful source material for other ICRU reports, the general considerations inmore » subsection 1.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. As in ICRU Report 19, the definitions of quantities and units specifically designed for radiation protection (Part B) are separated from those of the general quantities (Part A). The inclusion of the index concept outlined in ICRU Report 25(4) required an extension of Part B.« less

  10. Children's multiplicative transformations of discrete and continuous quantities.

    PubMed

    Barth, Hilary; Baron, Andrew; Spelke, Elizabeth; Carey, Susan

    2009-08-01

    Recent studies have documented an evolutionarily primitive, early emerging cognitive system for the mental representation of numerical quantity (the analog magnitude system). Studies with nonhuman primates, human infants, and preschoolers have shown this system to support computations of numerical ordering, addition, and subtraction involving whole number concepts prior to arithmetic training. Here we report evidence that this system supports children's predictions about the outcomes of halving and perhaps also doubling transformations. A total of 138 kindergartners and first graders were asked to reason about the quantity resulting from the doubling or halving of an initial numerosity (of a set of dots) or an initial length (of a bar). Controls for dot size, total dot area, and dot density ensured that children were responding to the number of dots in the arrays. Prior to formal instruction in symbolic multiplication, division, or rational number, halving (and perhaps doubling) computations appear to be deployed over discrete and possibly continuous quantities. The ability to apply simple multiplicative transformations to analog magnitude representations of quantity may form a part of the toolkit that children use to construct later concepts of rational number.

  11. Quantity quotient reporting. A proposal for a standardized presentation of laboratory results.

    PubMed

    Haeckel, Rainer; Wosniok, Werner

    2009-01-01

    Laboratory results are reported in different units (despite international recommendations for SI units) together with different reference limits, of which several exist for many quantities. It is proposed to adopt the concept of the intelligence quotient and to report quantitative results as a quantity quotient (QQ) in laboratory medicine. This quotient is essentially the difference (measured result minus mean or mode value of the reference interval) divided by the observed biological variation CV(o). Thus, all quantities are reported in the same unit system with the same reference limits (for convenience shifted to e.g., 80-120). The critical difference can also be included in this standardization concept. In this way the information of reference intervals and the original result are integrated into one combined value, which has the same format for all quantities suited for quotient reporting (QR). The proposal of QR does not interfere with neither the current concepts of traceability, SI units or method standardization. This proposal represents a further step towards harmonization of reporting. It provides simple values which can be interpreted easily by physicians and their patients.

  12. Units for quantities of dimension one

    NASA Astrophysics Data System (ADS)

    Dybkaer, René

    2004-02-01

    All quantities of dimension one are said to have the SI coherent derived unit "one" with the symbol '1'. (Single quotation marks are used here sometimes to indicate a quote, name, term or symbol; double quotation marks flag a concept when necessary.) Conventionally, the term and symbol may not be combined with the SI prefixes (except for the special terms and symbols for one and 1: radian, rad, and steradian, sr). This restriction is understandable, but leads to correct yet impractical alternatives and ISO deprecated symbols such as ppm or in some cases redundant combinations of units, such as mg/kg. "Number of entities" is dimensionally independent of the current base quantities and should take its rightful place among them. The corresponding base unit is "one". A working definition is given. Other quantities of dimension one are derived as fraction, ratio, efficiency, relative quantity, relative increment or characteristic number and may also use the unit "one", whether considered to be base or derived. The special term 'uno' and symbol 'u' in either case are proposed, allowing combination with SI prefixes.

  13. Conceptual Model of Quantities, Units, Dimensions, and Values

    NASA Technical Reports Server (NTRS)

    Rouquette, Nicolas F.; DeKoenig, Hans-Peter; Burkhart, Roger; Espinoza, Huascar

    2011-01-01

    JPL collaborated with experts from industry and other organizations to develop a conceptual model of quantities, units, dimensions, and values based on the current work of the ISO 80000 committee revising the International System of Units & Quantities based on the International Vocabulary of Metrology (VIM). By providing support for ISO 80000 in SysML via the International Vocabulary of Metrology (VIM), this conceptual model provides, for the first time, a standard-based approach for addressing issues of unit coherence and dimensional analysis into the practice of systems engineering with SysML-based tools. This conceptual model provides support for two kinds of analyses specified in the International Vocabulary of Metrology (VIM): coherence of units as well as of systems of units, and dimension analysis of systems of quantities. To provide a solid and stable foundation, the model for defining quantities, units, dimensions, and values in SysML is explicitly based on the concepts defined in VIM. At the same time, the model library is designed in such a way that extensions to the ISQ (International System of Quantities) and SI Units (Systeme International d Unites) can be represented, as well as any alternative systems of quantities and units. The model library can be used to support SysML user models in various ways. A simple approach is to define and document libraries of reusable systems of units and quantities for reuse across multiple projects, and to link units and quantity kinds from these libraries to Unit and QuantityKind stereotypes defined in SysML user models.

  14. Transformative Relation of Kinematical Descriptive Quantities Defined by Different Spatial Referential Frame, Its Property and Application

    NASA Astrophysics Data System (ADS)

    Luo, Ji

    2012-08-01

    Quantitative transformations between corresponding kinetic quantities defined by any two spatial referential frames, whose relative kinematics relations (purely rotational and translational movement) are known, are presented based on necessarily descriptive definitions of the fundamental concepts (instant, time, spatial referential frame that distinguishes from Maths. Coordination, physical point) had being clarified by directly empirical observation with artificially descriptive purpose. Inductive investigation of the transformation reveals that all physical quantities such as charge, temperature, time, volume, length, temporal rate of the quantities and relations like temporal relation between signal source and observer as such are independent to spatial frames transformation except above kinematical quantities transformations, kinematics related dynamics such as Newton ’ s second law existing only in inertial frames and exchange of kinetic energy of mass being valid only in a selected inertial frame. From above bas is, we demonstrate a series of inferences and applications such as phase velocity of light being direct respect to medium (including vacuum) rather than to the frame, using spatial referential frame to describe any measurable field (electric field, magnetic field, gravitational field) and the field ’ s variation; and have tables to contrast and evaluate all aspects of those hypotheses related with spacetime such as distorted spacetime around massive stellar, four dimension spacetime, gravitational time dilation and non - Euclid geometry with new one. The demonstration strongly suggests all the hypotheses are invalid in capable tested concepts ’ meaning and relations. The conventional work on frame transformation and its property, hypothesized by Voigt, Heaviside, Lorentz, Poincare and Einstein a century ago with some mathematical speculation lacking rigorous definition of the fundamental concepts such as instant, time, spatial reference

  15. Piagetian conservation of discrete quantities in bonobos (Pan paniscus), chimpanzees (Pan troglodytes), and orangutans (Pongo pygmaeus).

    PubMed

    Suda, Chikako; Call, Josep

    2005-10-01

    This study investigated whether physical discreteness helps apes to understand the concept of Piagetian conservation (i.e. the invariance of quantities). Subjects were four bonobos, three chimpanzees, and five orangutans. Apes were tested on their ability to conserve discrete/continuous quantities in an over-conservation procedure in which two unequal quantities of edible rewards underwent various transformations in front of subjects. Subjects were examined to determine whether they could track the larger quantity of reward after the transformation. Comparison between the two types of conservation revealed that tests with bonobos supported the discreteness hypothesis. Bonobos, but neither chimpanzees nor orangutans, performed significantly better with discrete quantities than with continuous ones. The results suggest that at least bonobos could benefit from the discreteness of stimuli in their acquisition of conservation skills.

  16. Self-concept, self-esteem and psychopathological symptoms.

    PubMed

    Garaigordobil, Maite; Pérez, José Ignacio; Mozaz, María

    2008-02-01

    This study has two objectives: 1) to analyse the characteristics of self-concept, self-esteem and psychopathological symptoms in accordance with age and gender in a representative sample from the Basque Country; and 2) to explore the relationships of self-concept and self-esteem with psychopathological symptoms. The sample is made up of 1,579 participants, aged 12 to 65, of whom 732 are males (46.4%) and 847 are females (53.6%). The study uses a descriptive and correlational methodology. For the measurement of psychopathological symptoms, self-concept and self-esteem, three assessment instruments are applied. The ANOVAs indicated significant differences associated with age in self-concept, self-esteem, and quantity of psychopathological symptoms. As regards gender, no significant differences were found for self-concept and self-esteem, but there were differences in psychopathological symptoms, with females scoring higher in various disorders (somatization, interpersonal sensitivity, depression, anxiety, phobic anxiety, and total quantity of symptoms). The results of the correlational analyses confirmed significant inverse relationships between self-concept/self-esteem and psychopathological symptoms. The discussion considers the potential role of intervention programmes that promote self-concept and self-esteem in the prevention of psychopathological problems.

  17. Weighting factors for radiation quality: how to unite the two current concepts.

    PubMed

    Kellerer, Albrecht M

    2004-01-01

    The quality factor, Q(L), used to be the universal weighting factor to account for radiation quality, until--in its 1991 Recommendations--the ICRP established a dichotomy between 'computable' and 'measurable' quantities. The new concept of the radiation weighting factor, w(R), was introduced for use with the 'computable' quantities, such as the effective dose, E. At the same time, the application of Q(L) was restricted to 'measurable' quantities, such as the operational quantities ambient dose equivalent or personal dose equivalent. The result has been a dual system of incoherent dosimetric quantities. The most conspicuous inconsistency resulted for neutrons, for which the new concept of wR had been primarily designed. While its definition requires an accounting for the gamma rays produced by neutron capture in the human body, this effect is not adequately reflected in the numerical values of wR, which are now suitable for mice, but are--at energies of the incident neutrons below 1 MeV--conspicuously too large for man. A recent Report 92 to ICRP has developed a proposal to correct the current imbalance and to define a linkage between the concepts Q(L) and wR. The proposal is here considered within a broader assessment of the rationale that led to the current dual system of dosimetric quantities.

  18. Quantity Stickiness versus Stackelberg Leadership

    NASA Astrophysics Data System (ADS)

    Ferreira, F. A.

    2008-10-01

    We study the endogenous Stackelberg relations in a dynamic market. We analyze a twice-repeated duopoly where, in the beginning, each firm chooses either a quantity-sticky production mode or a quantity-flexible production mode. The size of the market becomes observable after the first period. In the second period, a firm can adjust its quantity if, and only if, it has adopted the flexible mode. Hence, if one firm chooses the sticky mode whilst the other chooses the flexible mode, then they respectively play the roles of a Stackelberg leader and a Stackelberg follower in the second marketing period. We compute the supply quantities at equilibrium and the corresponding expected profits of the firms. We also analyze the effect of the slope parameter of the demand curve on the expected supply quantities and on the profits.

  19. Varieties of quantity estimation in children.

    PubMed

    Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

    2015-06-01

    In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3 children were asked to map continuous quantities, discrete nonsymbolic quantities (numerosities), and symbolic (Arabic) numbers onto a visual line. Numerical quantity was matched for the symbolic and discrete nonsymbolic conditions, whereas cumulative surface area was matched for the continuous and discrete quantity conditions. Crucially, in the discrete condition children's estimation could rely either on the cumulative area or numerosity. All children showed a linear mapping for continuous quantities, whereas a developmental shift from a logarithmic to a linear mapping was observed for both nonsymbolic and symbolic numerical quantities. Analyses on individual estimates suggested the presence of two distinct strategies in estimating discrete nonsymbolic quantities: one based on numerosity and the other based on spatial extent. In Experiment 2, a non-spatial continuous quantity (shades of gray) and new discrete nonsymbolic conditions were added to the set used in Experiment 1. Results confirmed the linear patterns for the continuous tasks, as well as the presence of a subset of children relying on numerosity for the discrete nonsymbolic numerosity conditions despite the availability of continuous visual cues. Overall, our findings demonstrate that estimation of numerical and non-numerical quantities is based on different processing strategies and follow different developmental trajectories. (c) 2015 APA, all rights reserved).

  20. 48 CFR 52.236-16 - Quantity Surveys.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 2 2013-10-01 2013-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

  1. 48 CFR 52.236-16 - Quantity Surveys.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 2 2011-10-01 2011-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

  2. 48 CFR 52.236-16 - Quantity Surveys.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 2 2012-10-01 2012-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

  3. 48 CFR 52.236-16 - Quantity Surveys.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 2 2014-10-01 2014-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

  4. 48 CFR 52.236-16 - Quantity Surveys.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

  5. 48 CFR 36.516 - Quantity surveys.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

  6. 48 CFR 36.516 - Quantity surveys.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

  7. 48 CFR 36.516 - Quantity surveys.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

  8. 48 CFR 36.516 - Quantity surveys.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

  9. 48 CFR 36.516 - Quantity surveys.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

  10. 14 CFR 27.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Oil quantity indicator. 27.1551 Section 27... § 27.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

  11. 14 CFR 29.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Oil quantity indicator. 29.1551 Section 29... Placards § 29.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

  12. 14 CFR 27.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Oil quantity indicator. 27.1551 Section 27... § 27.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

  13. 14 CFR 29.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Oil quantity indicator. 29.1551 Section 29... Placards § 29.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

  14. 14 CFR 27.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Oil quantity indicator. 27.1551 Section 27... § 27.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

  15. 14 CFR 29.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Oil quantity indicator. 29.1551 Section 29... Placards § 29.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

  16. 14 CFR 27.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Oil quantity indicator. 27.1551 Section 27... § 27.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

  17. The accuracy of less: Natural bounds explain why quantity decreases are estimated more accurately than quantity increases.

    PubMed

    Chandon, Pierre; Ordabayeva, Nailya

    2017-02-01

    Five studies show that people, including experts such as professional chefs, estimate quantity decreases more accurately than quantity increases. We argue that this asymmetry occurs because physical quantities cannot be negative. Consequently, there is a natural lower bound (zero) when estimating decreasing quantities but no upper bound when estimating increasing quantities, which can theoretically grow to infinity. As a result, the "accuracy of less" disappears (a) when a numerical or a natural upper bound is present when estimating quantity increases, or (b) when people are asked to estimate the (unbounded) ratio of change from 1 size to another for both increasing and decreasing quantities. Ruling out explanations related to loss aversion, symbolic number mapping, and the visual arrangement of the stimuli, we show that the "accuracy of less" influences choice and demonstrate its robustness in a meta-analysis that includes previously published results. Finally, we discuss how the "accuracy of less" may explain asymmetric reactions to the supersizing and downsizing of food portions, some instances of the endowment effect, and asymmetries in the perception of increases and decreases in physical and psychological distance. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  18. 14 CFR 23.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Oil quantity indicator. 23.1551 Section 23... Information Markings and Placards § 23.1551 Oil quantity indicator. Each oil quantity indicator must be marked in sufficient increments to indicate readily and accurately the quantity of oil. ...

  19. 14 CFR 23.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Oil quantity indicator. 23.1551 Section 23... Information Markings and Placards § 23.1551 Oil quantity indicator. Each oil quantity indicator must be marked in sufficient increments to indicate readily and accurately the quantity of oil. ...

  20. 14 CFR 23.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Oil quantity indicator. 23.1551 Section 23... Information Markings and Placards § 23.1551 Oil quantity indicator. Each oil quantity indicator must be marked in sufficient increments to indicate readily and accurately the quantity of oil. ...

  1. 14 CFR 23.1551 - Oil quantity indicator.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Oil quantity indicator. 23.1551 Section 23... Information Markings and Placards § 23.1551 Oil quantity indicator. Each oil quantity indicator must be marked in sufficient increments to indicate readily and accurately the quantity of oil. ...

  2. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

  3. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

  4. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

  5. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

  6. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

  7. 14 CFR 25.1551 - Oil quantity indication.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Oil quantity indication. 25.1551 Section 25... Placards § 25.1551 Oil quantity indication. Each oil quantity indicating means must be marked to indicate the quantity of oil readily and accurately. [Amdt. 25-72, 55 FR 29786, July 20, 1990] ...

  8. 14 CFR 25.1551 - Oil quantity indication.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Oil quantity indication. 25.1551 Section 25... Placards § 25.1551 Oil quantity indication. Each oil quantity indicating means must be marked to indicate the quantity of oil readily and accurately. [Amdt. 25-72, 55 FR 29786, July 20, 1990] ...

  9. 14 CFR 25.1551 - Oil quantity indication.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Oil quantity indication. 25.1551 Section 25... Placards § 25.1551 Oil quantity indication. Each oil quantity indicating means must be marked to indicate the quantity of oil readily and accurately. [Amdt. 25-72, 55 FR 29786, July 20, 1990] ...

  10. 14 CFR 25.1551 - Oil quantity indication.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Oil quantity indication. 25.1551 Section 25... Placards § 25.1551 Oil quantity indication. Each oil quantity indicating means must be marked to indicate the quantity of oil readily and accurately. [Amdt. 25-72, 55 FR 29786, July 20, 1990] ...

  11. Practical thermodynamic quantities for aqueous vanadium- and iron-based flow batteries

    DOE PAGES

    Hudak, Nicholas S.

    2013-12-31

    A simple method for experimentally determining thermodynamic quantities for flow battery cell reactions is presented. Equilibrium cell potentials, temperature derivatives of cell potential (d E/d T), Gibbs free energies, and entropies are reported here for all-vanadium, iron–vanadium, and iron–chromium flow cells with state-of-the-art solution compositions. Proof is given that formal potentials and formal temperature coefficients can be used with modified forms of the Nernst Equation to quantify the thermodynamics of flow cell reactions as a function of state-of-charge. Such empirical quantities can be used in thermo-electrochemical models of flow batteries at the cell or system level. In most cases, themore » thermodynamic quantities measured here are significantly different from standard values reported and used previously in the literature. The data reported here are also useful in the selection of operating temperatures for flow battery systems. Because higher temperatures correspond to lower equilibrium cell potentials for the battery chemistries studied here, it can be beneficial to charge a cell at higher temperature and discharge at lower temperature. As a result, proof-of-concept of improved voltage efficiency with the use of such non-isothermal cycling is given for the all-vanadium redox flow battery, and the effect is shown to be more pronounced at lower current densities.« less

  12. How Do We Present the Concept of Energy in Physics?

    ERIC Educational Resources Information Center

    Pujol, O.; Perez, J. P.

    2007-01-01

    Scientific and pedagogical comments about the fundamental physical concept of energy are made. In particular, we argue for an historical presentation of this concept because its essential justification is the research, conscious or not, of a characteristic quantity of a system whose fundamental property is to be conservative. Some delicate issues…

  13. Comparative Assessment of Physical and Social Determinants of Water Quantity and Water Quality Concerns

    NASA Astrophysics Data System (ADS)

    Gunda, T.; Hornberger, G. M.

    2017-12-01

    Concerns over water resources have evolved over time, from physical availability to economic access and recently, to a more comprehensive study of "water security," which is inherently interdisciplinary because a secure water system is influenced by and affects both physical and social components. The concept of water security carries connotations of both an adequate supply of water as well as water that meets certain quality standards. Although the term "water security" has many interpretations in the literature, the research field has not yet developed a synthetic analysis of water security as both a quantity (availability) and quality (contamination) issue. Using qualitative comparative and multi-regression analyses, we evaluate the primary physical and social factors influencing U.S. states' water security from a quantity perspective and from a quality perspective. Water system characteristics are collated from academic and government sources and include access/use, governance, and sociodemographic, and ecosystem metrics. Our analysis indicates differences in variables driving availability and contamination concerns; for example, climate is a more significant determinant in water quantity-based security analyses than in water quality-based security analyses. We will also discuss coevolution of system traits and the merits of constructing a robust water security index based on the relative importance of metrics from our analyses. These insights will improve understanding of the complex interactions between quantity and quality aspects and thus, overall security of water systems.

  14. Abyssal seafloor waste isolation: the concept

    NASA Astrophysics Data System (ADS)

    Valent, Philip J.; Young, David K.; Sawyer, William B.; Wright, Thomas D.

    1998-05-01

    The Naval Research Laboratory (NRL), with industry and university participation, conducted an assessment of the concept of isolating certain wastes (i.e., sewage sludge, fly ash from municipal incinerators, and contaminated dredged material) on the oceans' abyssal seafloor. In this assessment the advantages, disadvantages, and economic and environmental viability of potential engineering methods for achieving abyssal waste isolation were identified and compared. This paper presents background to the Abyssal Plains Waste Isolation (APWI) Project, describes the characteristics of the waste streams and quantities potentially available for disposal via the abyssal isolation concept, summarizes regulations affecting use of the abyssal seafloor for disposal of wastes, and introduces the technical and scientific premises underlying implementation of the concept.

  15. 40 CFR 201.21 - Quantities measured.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... § 201.21 Quantities measured. The quantities to be measured under the test conditions described below, are the A-weighted sound levels for “fast” or “slow” meter response as defined in the American...

  16. 40 CFR 201.21 - Quantities measured.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... § 201.21 Quantities measured. The quantities to be measured under the test conditions described below, are the A-weighted sound levels for “fast” or “slow” meter response as defined in the American...

  17. Quantity, Revisited: An Object-Oriented Reusable Class

    NASA Technical Reports Server (NTRS)

    Funston, Monica Gayle; Gerstle, Walter; Panthaki, Malcolm

    1998-01-01

    "Quantity", a prototype implementation of an object-oriented class, was developed for two reasons: to help engineers and scientists manipulate the many types of quantities encountered during routine analysis, and to create a reusable software component to for large domain-specific applications. From being used as a stand-alone application to being incorporated into an existing computational mechanics toolkit, "Quantity" appears to be a useful and powerful object. "Quantity" has been designed to maintain the full engineering meaning of values with respect to units and coordinate systems. A value is a scalar, vector, tensor, or matrix, each of which is composed of Value Components, each of which may be an integer, floating point number, fuzzy number, etc., and its associated physical unit. Operations such as coordinate transformation and arithmetic operations are handled by member functions of "Quantity". The prototype has successfully tested such characteristics as maintaining a numeric value, an associated unit, and an annotation. In this paper we further explore the design of "Quantity", with particular attention to coordinate systems.

  18. Thermodynamics of quantum systems with multiple conserved quantities

    PubMed Central

    Guryanova, Yelena; Popescu, Sandu; Short, Anthony J.; Silva, Ralph; Skrzypczyk, Paul

    2016-01-01

    Recently, there has been much progress in understanding the thermodynamics of quantum systems, even for small individual systems. Most of this work has focused on the standard case where energy is the only conserved quantity. Here we consider a generalization of this work to deal with multiple conserved quantities. Each conserved quantity, which, importantly, need not commute with the rest, can be extracted and stored in its own battery. Unlike the standard case, in which the amount of extractable energy is constrained, here there is no limit on how much of any individual conserved quantity can be extracted. However, other conserved quantities must be supplied, and the second law constrains the combination of extractable quantities and the trade-offs between them. We present explicit protocols that allow us to perform arbitrarily good trade-offs and extract arbitrarily good combinations of conserved quantities from individual quantum systems. PMID:27384384

  19. Kinematics, influence functions and field quantities for disturbance propagation from moving disturbance sources

    NASA Technical Reports Server (NTRS)

    Das, A.

    1984-01-01

    A unified method is presented for deriving the influence functions of moving singularities which determine the field quantities in aerodynamics and aeroacoustics. The moving singularities comprise volume and surface distributions having arbitrary orientations in space and to the trajectory. Hence one generally valid formula for the influence functions which reveal some universal relationships and remarkable properties in the disturbance fields. The derivations used are completely consistent with the physical processes in the propagation field, such that treatment renders new descriptions for some standard concepts. The treatment is uniformly valid for subsonic and supersonic Mach numbers.

  20. 36 CFR 223.220 - Quantity determination.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Quantity determination. 223.220 Section 223.220 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER Special Forest Products § 223.220 Quantity determination...

  1. Quantifying cannabis: A field study of marijuana quantity estimation.

    PubMed

    Prince, Mark A; Conner, Bradley T; Pearson, Matthew R

    2018-06-01

    The assessment of marijuana use quantity poses unique challenges. These challenges have limited research efforts on quantity assessments. However, quantity estimates are critical to detecting associations between marijuana use and outcomes. We examined accuracy of marijuana users' estimations of quantities of marijuana they prepared to ingest and predictors of both how much was prepared for a single dose and the degree of (in)accuracy of participants' estimates. We recruited a sample of 128 regular-to-heavy marijuana users for a field study wherein they prepared and estimated quantities of marijuana flower in a joint or a bowl as well as marijuana concentrate using a dab tool. The vast majority of participants overestimated the quantity of marijuana that they used in their preparations. We failed to find robust predictors of estimation accuracy. Self-reported quantity estimates are inaccurate, which has implications for studying the link between quantity and marijuana use outcomes. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  2. Study of LED modulation effect on the photometric quantities and beam homogeneity of automotive lighting

    NASA Astrophysics Data System (ADS)

    Koudelka, Petr; Hanulak, Patrik; Jaros, Jakub; Papes, Martin; Latal, Jan; Siska, Petr; Vasinek, Vladimir

    2015-07-01

    This paper discusses the implementation of a light emitting diode based visible light communication system for optical vehicle-to-vehicle (V2V) communications in road safety applications. The widespread use of LEDs as light sources has reached into automotive fields. For example, LEDs are used for taillights, daytime running lights, brake lights, headlights, and traffic signals. Future in the optical vehicle-to-vehicle (V2V) communications will be based on an optical wireless communication technology that using LED transmitter and a camera receiver (OCI; optical communication image sensor). Utilization of optical V2V communication systems in automotive industry naturally brings a lot of problems. Among them belongs necessity of circuit implementation into the current concepts of electronic LED lights control that allows LED modulation. These circuits are quite complicated especially in case of luxury cars. Other problem is correct design of modulation circuits so that final vehicle lightning using optical vehicle-to-vehicle (V2V) communication meets standard requirements on Photometric Quantities and Beam Homogeneity. Authors of this article performed research on optical vehicle-to-vehicle (V2V) communication possibilities of headlight (Jaguar) and taillight (Skoda) in terms of modulation circuits (M-PSK, M-QAM) implementation into the lamp concepts and final fulfilment of mandatory standards on Photometric Quantities and Beam Homogeneity.

  3. Alternative Conceptions: Turning Adversity into Advantage

    NASA Astrophysics Data System (ADS)

    Ferreira, Annalize; Lemmer, Miriam; Gunstone, Richard

    2017-08-01

    While a vast body of research has identified difficulties in students' understanding about forces and acceleration and their related alternative conceptions, far less research suggests ways to use students' alternative conceptions to enhance conceptual understanding of a specific fundamental concept. This study focused on distinguishing between students' conceptual understanding of the Newtonian concept of gravitational acceleration being the same for all objects and students' alternative conception that heavy objects fall faster. A multiple choice questionnaire was distributed to first year physics students for three consecutive years at a university in South Africa. The results indicate that changing the direction of motion and the physics quantity asked in paired questions revealed practically significant inconsistencies in students' reasoning and conceptions. This research contributes to the body of knowledge in proposing how the alternative conception of mass-related gravitational acceleration can be used in instruction to enhance conceptual understanding of the force-mass-acceleration relationship. Understanding of this relationship not only promotes conceptual understanding of the basic Newtonian concepts of the laws of motion which forms the critical foundation on which more advanced physics courses are built, but also contributes towards students' perception of physics as a set of coherent ideas applicable in all contexts.

  4. 49 CFR 172.315 - Limited quantities.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... accordance with the white square-on-point limited quantity marking as follows: (1) The limited quantity... forming the square-on-point must be at least 2 mm and the minimum dimension of each side must be 100 mm... top and bottom portions of the square-on-point and the border forming the square-on-point must be...

  5. The influence of intuition and communication language in generating student conceptions

    NASA Astrophysics Data System (ADS)

    Handhika, J.; Cari, C.; Suparmi, A.; Sunarno, W.

    2017-11-01

    This research aims to describe the influence of intuition and communication language in generating student conceptions. The conception diagnostic test is used to reveal student conception. The diagnostic test results described and communication language profiled by giving instruction to students to make sentences using physics quantities. Sentences expressed by students are reduced and profiled potential effects. Obtained information that (1) Students generalize non-scientific experience (based on feeling) into the physics problem. This process caused misconception. Communication language can make the students difficult to understand the concept because of the difference meaning of communication and physics language.

  6. The Acquisition of Quantity Contrasts in Guina-ang Bontok

    ERIC Educational Resources Information Center

    Aoyama, Katsura; Reid, Lawrence A.

    2016-01-01

    This study reports on the acquisition of quantity contrasts in Guina-ang Bontok, an indigenous language spoken in the Philippines. Four-year-old and 5-year-old children's perception and production of quantity contrasts were examined using a pair of names that contrast in the quantity of the medial nasal. Frequencies of the quantity contrast were…

  7. A Brief History of the NPS Field Experimentation Program: Spanning STAN, TNT, and JIFX

    DTIC Science & Technology

    2014-08-01

    located near the post’s southern boundary at 35o 43’N 120o 46’W (UTM Grid 10SGQ 025546). McMillan Ai rfield is 3500’ long, 65’ wide with 10’ shoulders ...Reconnaissance Vehicle. Advisor: Dr. Alex Bordetsky. Second Reader: Dr. Dave Netzer 57 LtCol Tim Lamb , USA Future Unmanned Aerial Vehicle (UAV

  8. The Concept of Ionic Strength Eighty Years after Its Introduction in Chemistry

    ERIC Educational Resources Information Center

    Manuel E. Sastre de Vicente

    2004-01-01

    Some comments on the relationship of ionic strength to macroscopic concepts such as thermodynamic quantities and microscopic ones such as molecule size are presented. The meaning of ionic strength is also reviewed.

  9. An Algebraic Approach to Unital Quantities and their Measurement

    NASA Astrophysics Data System (ADS)

    Domotor, Zoltan; Batitsky, Vadim

    2016-06-01

    The goals of this paper fall into two closely related areas. First, we develop a formal framework for deterministic unital quantities in which measurement unitization is understood to be a built-in feature of quantities rather than a mere annotation of their numerical values with convenient units. We introduce this idea within the setting of certain ordered semigroups of physical-geometric states of classical physical systems. States are assumed to serve as truth makers of metrological statements about quantity values. A unital quantity is presented as an isomorphism from the target system's ordered semigroup of states to that of positive reals. This framework allows us to include various derived and variable quantities, encountered in engineering and the natural sciences. For illustration and ease of presentation, we use the classical notions of length, time, electric current and mean velocity as primordial examples. The most important application of the resulting unital quantity calculus is in dimensional analysis. Second, in evaluating measurement uncertainty due to the analog-to-digital conversion of the measured quantity's value into its measuring instrument's pointer quantity value, we employ an ordered semigroup framework of pointer states. Pointer states encode the measuring instrument's indiscernibility relation, manifested by not being able to distinguish the measured system's topologically proximal states. Once again, we focus mainly on the measurement of length and electric current quantities as our motivating examples. Our approach to quantities and their measurement is strictly state-based and algebraic in flavor, rather than that of a representationalist-style structure-preserving numerical assignment.

  10. INTERNATIONAL REPORTS: New International Standards for Quantities and Units

    NASA Astrophysics Data System (ADS)

    Thor, A. J.

    1994-01-01

    Each coherent system of units is based on a system of quantities in such a way that the equations between the numerical values expressed in coherent units have exactly the same form, including numerical factors, as the corresponding equations between the quantities. The highest international body responsible for the International System of Units (SI) is the Conférence Générale des Poids et Mesures (CGPM). However, the CGPM is not concerned with quantities or systems of quantities. That question lies within the scope of Technical Committee number twelve of the International Organization for Standardization (ISO/TC 12). Quantities, units, symbols, conversion factors. To fulfil its responsibility, ISO/TC 12 has prepared the International Standard ISO 31, Quantities and Units, which consists of fourteen parts. The new editions of the different parts of the International Standard are briefly presented here.

  11. A Real Options Approach to Quantity and Cost Optimization for Lifetime and Bridge Buys of Parts

    DTIC Science & Technology

    2015-12-01

    Optimization for Lifetime and Bridge Buys of Parts By: Peter Sandborn and Navid Goudarzi 18 56 U N IV ERSITY O F M A R Y L A N D UMD-LM-16-011 Electronic...and bridge buys, which are used to manage part discontinuance (i.e., obsolescence) during the support of critical systems are simple in concept, the...valuate lifetime and bridge buys and to determine the optimum part quantity for a lifetime or bridge buy. The approach accommodates uncertainties in

  12. 48 CFR 816.504 - Indefinite-quantity contracts.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... issue a solicitation for estimated quantities, the contracting officer shall insert the clause at 852.216-70, Estimated quantities. (b) The contracting officer shall insert the Alternate I clause at 852.216-70 in solicitations for bulk coal. (c) The contracting officer shall insert the Alternate II...

  13. Hypergraph topological quantities for tagged social networks.

    PubMed

    Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

    2009-09-01

    Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

  14. Hypergraph topological quantities for tagged social networks

    NASA Astrophysics Data System (ADS)

    Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

    2009-09-01

    Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

  15. Relative quantity judgments in South American sea lions (Otaria flavescens).

    PubMed

    Abramson, José Z; Hernández-Lloreda, Victoria; Call, Josep; Colmenares, Fernando

    2011-09-01

    There is accumulating evidence that a variety of species possess quantitative abilities although their cognitive substrate is still unclear. This study is the first to investigate whether sea lions (Otaria flavescens), in the absence of training, are able to assess and select the larger of two sets of quantities. In Experiment 1, the two sets of quantities were presented simultaneously as whole sets, that is, the subjects could compare them directly. In Experiment 2, the two sets of quantities were presented item-by-item, and the totality of items was never visually available at the time of choice. For each type of presentation, we analysed the effect of the ratio between quantities, the difference between quantities and the total number of items presented. The results showed that (1) sea lions can make relative quantity judgments successfully and (2) there is a predominant influence of the ratio between quantities on the subjects' performance. The latter supports the idea that an analogue representational mechanism is responsible for sea lions' relative quantities judgments. These findings are consistent with previous reports of relative quantities judgments in other species such as monkeys and apes and suggest that sea lions might share a similar mechanism to compare and represent quantities.

  16. 14 CFR 25.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel quantity indicator. 25.1553 Section 25.1553 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Placards § 25.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or...

  17. 14 CFR 23.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel quantity indicator. 23.1553 Section 23.1553 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Information Markings and Placards § 23.1553 Fuel quantity indicator. A red radial line must be marked on each...

  18. 49 CFR 173.4a - Excepted quantities.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... ice), and lithium batteries and cells. (c) Inner packaging limits. The maximum quantity of hazardous materials in each inner packaging is limited to: (1) For toxic material with a Division 6.1 primary or... excepted quantities must meet the following: (1) Each inner receptacle must be constructed of plastic, or...

  19. 10 CFR 26.109 - Urine specimen quantity.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine specimen quantity. (a) Licensees and other entities who are subject to this subpart shall establish a...

  20. 10 CFR 26.109 - Urine specimen quantity.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 1 2011-01-01 2011-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine specimen quantity. (a) Licensees and other entities who are subject to this subpart shall establish a...

  1. 41 CFR 101-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

  2. 41 CFR 101-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 41 Public Contracts and Property Management 2 2011-07-01 2007-07-01 true Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

  3. 41 CFR 101-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 41 Public Contracts and Property Management 2 2012-07-01 2012-07-01 false Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

  4. 41 CFR 101-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 41 Public Contracts and Property Management 2 2013-07-01 2012-07-01 true Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

  5. 41 CFR 101-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 41 Public Contracts and Property Management 2 2014-07-01 2012-07-01 true Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

  6. Supply chain coordination with defective items and quantity discount

    NASA Astrophysics Data System (ADS)

    Lin, Hsien-Jen; Lin, Yu-Jen

    2014-12-01

    This study develops an integrated inventory system involving defective items and quantity discount for optimal pricing and ordering strategies. The model analysed in this study is one in which the buyer orders a quantity, the vendor produces more than buyer's order quantity in order to reduce set-up cost, and then he/she offers an all-units quantity discount to the buyer. Our objective is to determine the optimal order quantity, retail price, mark-up rate, and the number of shipments per production run from the vendor to the buyer, so that the entire supply chain joint total profit incurred has a maximum value. Furthermore, an algorithm of finding the optimal solution is developed. Numerical examples are provided to illustrate the theoretical results.

  7. 7 CFR 1207.511 - Determination of assessable quantity.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... POTATO RESEARCH AND PROMOTION PLAN Rules and Regulations Assessments § 1207.511 Determination of assessable quantity. The assessable quantity of potatoes in any lot shall be determined on the basis of...

  8. 7 CFR 1207.511 - Determination of assessable quantity.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... POTATO RESEARCH AND PROMOTION PLAN Rules and Regulations Assessments § 1207.511 Determination of assessable quantity. The assessable quantity of potatoes in any lot shall be determined on the basis of...

  9. 7 CFR 1207.511 - Determination of assessable quantity.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... POTATO RESEARCH AND PROMOTION PLAN Rules and Regulations Assessments § 1207.511 Determination of assessable quantity. The assessable quantity of potatoes in any lot shall be determined on the basis of...

  10. Rethinking Intensive Quantities via Guided Mediated Abduction

    ERIC Educational Resources Information Center

    Abrahamson, Dor

    2012-01-01

    Some intensive quantities, such as slope, velocity, or likelihood, are perceptually privileged in the sense that they are experienced as holistic, irreducible sensations. However, the formal expression of these quantities uses "a/b" analytic metrics; for example, the slope of a line is the quotient of its rise and run. Thus, whereas students'…

  11. 7 CFR 1434.9 - Determination of quantity.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATIONS FOR HONEY § 1434.9 Determination of quantity. The amount of a marketing assistance loan and loan... the producer and verified by the county office representative for honey on Form CCC-633 (Honey) that is eligible to be pledged as security for the loan or LDP Estimates of the quantity of honey shall be...

  12. 7 CFR 1434.9 - Determination of quantity.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... REGULATIONS FOR HONEY § 1434.9 Determination of quantity. The amount of a marketing assistance loan and loan... the producer and verified by the county office representative for honey on Form CCC-633 (Honey) that is eligible to be pledged as security for the loan or LDP Estimates of the quantity of honey shall be...

  13. Quantity Competition in a Differentiated Duopoly

    NASA Astrophysics Data System (ADS)

    Ferreira, Fernanda A.; Ferreira, Flávio; Ferreira, Miguel; Pinto, Alberto A.

    In this paper, we consider a Stackelberg duopoly competition with differentiated goods, linear and symmetric demand and with unknown costs. In our model, the two firms play a non-cooperative game with two stages: in a first stage, firm F 1 chooses the quantity, q 1, that is going to produce; in the second stage, firm F 2 observes the quantity q 1 produced by firm F 1 and chooses its own quantity q 2. Firms choose their output levels in order to maximise their profits. We suppose that each firm has two different technologies, and uses one of them following a certain probability distribution. The use of either one or the other technology affects the unitary production cost. We show that there is exactly one perfect Bayesian equilibrium for this game. We analyse the variations of the expected profits with the parameters of the model, namely with the parameters of the probability distributions, and with the parameters of the demand and differentiation.

  14. 14 CFR 25.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel quantity indicator. 25.1553 Section 25... Placards § 25.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or five percent of the tank capacity, whichever is greater, a red arc must be marked on its indicator...

  15. 14 CFR 27.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel quantity indicator. 27.1553 Section 27... § 27.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or five percent of the tank capacity, whichever is greater, a red arc must be marked on its indicator extending...

  16. 14 CFR 23.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel quantity indicator. 23.1553 Section 23... Information Markings and Placards § 23.1553 Fuel quantity indicator. A red radial line must be marked on each indicator at the calibrated zero reading, as specified in § 23.1337(b)(1). [Doc. No. 27807, 61 FR 5193, Feb...

  17. 14 CFR 29.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel quantity indicator. 29.1553 Section 29... Placards § 29.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or five percent of the tank capacity, whichever is greater, a red arc must be marked on its indicator...

  18. 14 CFR 23.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel quantity indicator. 23.1553 Section 23... Information Markings and Placards § 23.1553 Fuel quantity indicator. A red radial line must be marked on each indicator at the calibrated zero reading, as specified in § 23.1337(b)(1). [Doc. No. 27807, 61 FR 5193, Feb...

  19. 14 CFR 27.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel quantity indicator. 27.1553 Section 27... § 27.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or five percent of the tank capacity, whichever is greater, a red arc must be marked on its indicator extending...

  20. Reportable Quantities Federal Register Notices

    EPA Pesticide Factsheets

    Comprehensive Environmental Response, Compensation and Liability Act regulation designates specific substances as hazardous; identifies the quantity of substances which, when released, requires notification; and sets forth the notification requirements.

  1. 48 CFR 14.212 - Economic purchase quantities (supplies).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

  2. 49 CFR 224.105 - Sheeting dimensions and quantity.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

  3. 49 CFR 224.105 - Sheeting dimensions and quantity.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

  4. 49 CFR 224.105 - Sheeting dimensions and quantity.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

  5. 49 CFR 224.105 - Sheeting dimensions and quantity.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

  6. 49 CFR 224.105 - Sheeting dimensions and quantity.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

  7. 40 CFR 302.5 - Determination of reportable quantities.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 28 2011-07-01 2011-07-01 false Determination of reportable quantities. 302.5 Section 302.5 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SUPERFUND, EMERGENCY PLANNING, AND COMMUNITY RIGHT-TO-KNOW PROGRAMS DESIGNATION, REPORTABLE QUANTITIES, AND...

  8. 48 CFR 14.212 - Economic purchase quantities (supplies).

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

  9. 48 CFR 14.212 - Economic purchase quantities (supplies).

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

  10. 48 CFR 14.212 - Economic purchase quantities (supplies).

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

  11. 48 CFR 14.212 - Economic purchase quantities (supplies).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

  12. Modality-independent representations of small quantities based on brain activation patterns.

    PubMed

    Damarla, Saudamini Roy; Cherkassky, Vladimir L; Just, Marcel Adam

    2016-04-01

    Machine learning or MVPA (Multi Voxel Pattern Analysis) studies have shown that the neural representation of quantities of objects can be decoded from fMRI patterns, in cases where the quantities were visually displayed. Here we apply these techniques to investigate whether neural representations of quantities depicted in one modality (say, visual) can be decoded from brain activation patterns evoked by quantities depicted in the other modality (say, auditory). The main finding demonstrated, for the first time, that quantities of dots were decodable by a classifier that was trained on the neural patterns evoked by quantities of auditory tones, and vice-versa. The representations that were common across modalities were mainly right-lateralized in frontal and parietal regions. A second finding was that the neural patterns in parietal cortex that represent quantities were common across participants. These findings demonstrate a common neuronal foundation for the representation of quantities across sensory modalities and participants and provide insight into the role of parietal cortex in the representation of quantity information. © 2016 Wiley Periodicals, Inc.

  13. Satellite Power Systems (SPS) concept definition study, exhibit C. Volume 1: Executive summary

    NASA Technical Reports Server (NTRS)

    Hanley, G. M.

    1979-01-01

    The Department of Energy (DOE) is currently conducting an evaluation of approaches to provide energy to meet demands in the post-2000 time period. The Satellite Power System (SPS) is a candidate for producing significant quantities of base-load power using solar energy as the source. The SPS concept is illustrated for a solar photovoltaic concept. A satellite, located at geosynchronous orbit, converts solar energy to dc electrical energy using large solar arrays. This study is a continuing effort to provide system definition data to aid in the evaluation of the SPS concept.

  14. Quantity Discrimination in Wolves (Canis lupus)

    PubMed Central

    Utrata, Ewelina; Virányi, Zsófia; Range, Friederike

    2012-01-01

    Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested 11 hand-raised wolves (Canis lupus) in a two-way choice task. We placed a number of food items (one to four) sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris) and coyotes (Canis latrans), our wolves’ performance did not improve with decreasing ratio, referred to as Weber’s law. However, further studies using larger quantities than we used in the current set-up are still needed to determine whether and when wolves’ quantity discrimination conforms to Weber’s law. PMID:23181044

  15. Quantity Discrimination in Wolves (Canis lupus).

    PubMed

    Utrata, Ewelina; Virányi, Zsófia; Range, Friederike

    2012-01-01

    Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested 11 hand-raised wolves (Canis lupus) in a two-way choice task. We placed a number of food items (one to four) sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris) and coyotes (Canis latrans), our wolves' performance did not improve with decreasing ratio, referred to as Weber's law. However, further studies using larger quantities than we used in the current set-up are still needed to determine whether and when wolves' quantity discrimination conforms to Weber's law.

  16. Boundary conditions for developing a safety concept for an exothermal reaction.

    PubMed

    Hauptmanns, Ulrich

    2007-09-05

    Kinetic calculations for an example exothermal chemical process, the production of TCB, are carried out. They address both parameter uncertainties and random failures of the cooling system. In this way, they enable one to establish comprehensive boundary conditions for a safety system in terms of unavailability, the quantities of the undesired by-product (TCDD) produced and the times available before a required intervention, if a pre-determined quantity of TCDD is tolerated. It is shown that accounting for stochastic effects and uncertainties derived from insufficient knowledge provides a broader and more realistic knowledge base for devising a viable safety concept.

  17. 27 CFR 555.213 - Quantity and storage restrictions.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Quantity and storage..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.213 Quantity and storage restrictions. (a) Explosive materials in excess of 300,000 pounds or detonators in...

  18. 27 CFR 555.213 - Quantity and storage restrictions.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Quantity and storage..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.213 Quantity and storage restrictions. (a) Explosive materials in excess of 300,000 pounds or detonators in...

  19. 27 CFR 555.213 - Quantity and storage restrictions.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Quantity and storage..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.213 Quantity and storage restrictions. (a) Explosive materials in excess of 300,000 pounds or detonators in...

  20. Forage quantity and quality

    USGS Publications Warehouse

    Jorgenson, Janet C.; Udevitz, Mark S.; Felix, Nancy A.; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

    2002-01-01

    The Porcupine caribou herd has traditionally used the coastal plain of the Arctic National Wildlife Refuge, Alaska, for calving. Availability of nutritious forage has been hypothesized as one of the reasons the Porcupine caribou herd migrates hundreds of kilometers to reach the coastal plain for calving (Kuropat and Bryant 1980, Russell et al. 1993).Forage quantity and quality and the chronology of snowmelt (which determines availability and phenological stages of forage) have been suggested as important habitat attributes that lead calving caribou to select one area over another (Lent 1980, White and Trudell 1980, Eastland et al. 1989). A major question when considering the impact of petroleum development is whether potential displacement of the caribou from the 1002 Area to alternate calving habitat will limit access to high quantity and quality forage.Our study had the following objectives: 1) quantify snowmelt patterns by area; 2) quantify relationships among phenology, biomass, and nutrient content of principal forage species by vegetation type; and 3) determine if traditional concentrated calving areas differ from adjacent areas with lower calving densities in terms of vegetation characteristics.

  1. A novel algorithm for the calculation of physical and biological irradiation quantities in scanned ion beam therapy: the beamlet superposition approach

    NASA Astrophysics Data System (ADS)

    Russo, G.; Attili, A.; Battistoni, G.; Bertrand, D.; Bourhaleb, F.; Cappucci, F.; Ciocca, M.; Mairani, A.; Milian, F. M.; Molinelli, S.; Morone, M. C.; Muraro, S.; Orts, T.; Patera, V.; Sala, P.; Schmitt, E.; Vivaldo, G.; Marchetto, F.

    2016-01-01

    The calculation algorithm of a modern treatment planning system for ion-beam radiotherapy should ideally be able to deal with different ion species (e.g. protons and carbon ions), to provide relative biological effectiveness (RBE) evaluations and to describe different beam lines. In this work we propose a new approach for ion irradiation outcomes computations, the beamlet superposition (BS) model, which satisfies these requirements. This model applies and extends the concepts of previous fluence-weighted pencil-beam algorithms to quantities of radiobiological interest other than dose, i.e. RBE- and LET-related quantities. It describes an ion beam through a beam-line specific, weighted superposition of universal beamlets. The universal physical and radiobiological irradiation effect of the beamlets on a representative set of water-like tissues is evaluated once, coupling the per-track information derived from FLUKA Monte Carlo simulations with the radiobiological effectiveness provided by the microdosimetric kinetic model and the local effect model. Thanks to an extension of the superposition concept, the beamlet irradiation action superposition is applicable for the evaluation of dose, RBE and LET distributions. The weight function for the beamlets superposition is derived from the beam phase space density at the patient entrance. A general beam model commissioning procedure is proposed, which has successfully been tested on the CNAO beam line. The BS model provides the evaluation of different irradiation quantities for different ions, the adaptability permitted by weight functions and the evaluation speed of analitical approaches. Benchmarking plans in simple geometries and clinical plans are shown to demonstrate the model capabilities.

  2. 7 CFR 983.53 - Testing of minimal quantities.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., ARIZONA, AND NEW MEXICO Regulations § 983.53 Testing of minimal quantities. (a) Aflatoxin. Handlers who... § 983.50. (b) Quality. The committee may, with the approval of the Secretary, establish regulations regarding the testing of minimal quantities of pistachios for quality. [74 FR 56540, Nov. 2, 2009] ...

  3. 40 CFR 302.5 - Determination of reportable quantities.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... reportable quantities listed in Table 302.4 for the contaminant on which the characteristic of toxicity is based. The reportable quantity applies to the waste itself, not merely to the toxic contaminant. If an unlisted hazardous waste exhibits toxicity on the basis of more than one contaminant, the reportable...

  4. Difference in quantity discrimination in dogs and wolves.

    PubMed

    Range, Friederike; Jenikejew, Julia; Schröder, Isabelle; Virányi, Zsófia

    2014-01-01

    Certain aspects of social life, such as engaging in intergroup conflicts, as well as challenges posed by the physical environment, may facilitate the evolution of quantity discrimination. In lack of excessive comparative data, one can only hypothesize about its evolutionary origins, but human-raised wolves performed well when they had to choose the larger of two sets of 1-4 food items that had been sequentially placed into two opaque cans. Since in such paradigms, the animals never see the entire content of either can, their decisions are thought to rely on mental representation of the two quantities rather than on some perceptual factors such as the overall volume or surface area of the two amounts. By equaling the time that it takes to enter each quantity into the cans or the number of items entered, one can further rule out the possibility that animals simply choose based on the amount of time needed to present the two quantities. While the wolves performed well even in such a control condition, dogs failed to choose the larger one of two invisible quantities in another study using a similar paradigm. Because this disparity could be explained by procedural differences, in the current study, we set out to test dogs that were raised and kept identically as the previously tested wolves using the same set-up and procedure. Our results confirm the former finding that dogs, in comparison to wolves, have inferior skills to represent quantities mentally. This seems to be in line with Frank's (1980) hypothesis suggesting that domestication altered the information processing of dogs. However, as discussed, also alternative explanations may exist.

  5. Difference in quantity discrimination in dogs and wolves

    PubMed Central

    Range, Friederike; Jenikejew, Julia; Schröder, Isabelle; Virányi, Zsófia

    2014-01-01

    Certain aspects of social life, such as engaging in intergroup conflicts, as well as challenges posed by the physical environment, may facilitate the evolution of quantity discrimination. In lack of excessive comparative data, one can only hypothesize about its evolutionary origins, but human-raised wolves performed well when they had to choose the larger of two sets of 1–4 food items that had been sequentially placed into two opaque cans. Since in such paradigms, the animals never see the entire content of either can, their decisions are thought to rely on mental representation of the two quantities rather than on some perceptual factors such as the overall volume or surface area of the two amounts. By equaling the time that it takes to enter each quantity into the cans or the number of items entered, one can further rule out the possibility that animals simply choose based on the amount of time needed to present the two quantities. While the wolves performed well even in such a control condition, dogs failed to choose the larger one of two invisible quantities in another study using a similar paradigm. Because this disparity could be explained by procedural differences, in the current study, we set out to test dogs that were raised and kept identically as the previously tested wolves using the same set-up and procedure. Our results confirm the former finding that dogs, in comparison to wolves, have inferior skills to represent quantities mentally. This seems to be in line with Frank’s (1980) hypothesis suggesting that domestication altered the information processing of dogs. However, as discussed, also alternative explanations may exist. PMID:25477834

  6. Defining value through quantity and quality-Chimpanzees (Pan troglodytes) undervalue food quantities when items are broken.

    PubMed

    Parrish, Audrey E; Evans, Theodore A; Beran, Michael J

    2015-02-01

    Decision-making largely is influenced by the relative value of choice options, and the value of such options can be determined by a combination of different factors (e.g., the quantity, size, or quality of a stimulus). In this study, we examined the competing influences of quantity (i.e., the number of food items in a set) and quality (i.e., the original state of a food item) of choice items on chimpanzees' food preferences in a two-option natural choice paradigm. In Experiment 1, chimpanzees chose between sets of food items that were either entirely whole or included items that were broken into pieces before being shown to the chimpanzees. Chimpanzees exhibited a bias for whole food items even when such choice options consisted of a smaller overall quantity of food than the sets containing broken items. In Experiment 2, chimpanzees chose between sets of entirely whole food items and sets of initially whole items that were subsequently broken in view of the chimpanzees just before choice time. Chimpanzees continued to exhibit a bias for sets of whole items. In Experiment 3, chimpanzees chose between sets of new food items that were initially discrete but were subsequently transformed into a larger cohesive unit. Here, chimpanzees were biased to choose the discrete sets that retained their original qualitative state rather than toward the cohesive or clumped sets. These results demonstrate that beyond a food set's quantity (i.e., the value dimension that accounts for maximization in terms of caloric intake), other seemingly non-relevant features (i.e., quality in terms of a set's original state) affect how chimpanzees assign value to their choice options. Copyright © 2014 Elsevier B.V. All rights reserved.

  7. A conserved quantity in thin body dynamics

    NASA Astrophysics Data System (ADS)

    Hanna, J. A.; Pendar, H.

    2016-02-01

    Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant.

  8. Lie-Mei symmetry and conserved quantities of the Rosenberg problem

    NASA Astrophysics Data System (ADS)

    Liu, Xiao-Wei; Li, Yuan-Cheng

    2011-07-01

    The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry.

  9. Strategies for Estimating Discrete Quantities.

    ERIC Educational Resources Information Center

    Crites, Terry W.

    1993-01-01

    Describes the benchmark and decomposition-recomposition estimation strategies and presents five techniques to develop students' estimation ability. Suggests situations involving quantities of candy and popcorn in which the teacher can model those strategies for the students. (MDH)

  10. Numerical Order and Quantity Processing in Number Comparison

    ERIC Educational Resources Information Center

    Turconi, Eva; Campbell, Jamie I. D.; Seron, Xavier

    2006-01-01

    We investigated processing of numerical order information and its relation to mechanisms of numerical quantity processing. In two experiments, performance on a quantity-comparison task (e.g. 2 5; which is larger?) was compared with performance on a relative-order judgment task (e.g. 2 5; ascending or descending order?). The comparison task…

  11. 30 CFR 36.45 - Quantity of ventilating air.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quantity of ventilating air. 36.45 Section 36... TRANSPORTATION EQUIPMENT Test Requirements § 36.45 Quantity of ventilating air. (a) Results of the engine tests shall be used to calculate ventilation (cubic feet of air per minute) that shall be supplied by positive...

  12. 30 CFR 36.45 - Quantity of ventilating air.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quantity of ventilating air. 36.45 Section 36... TRANSPORTATION EQUIPMENT Test Requirements § 36.45 Quantity of ventilating air. (a) Results of the engine tests shall be used to calculate ventilation (cubic feet of air per minute) that shall be supplied by positive...

  13. 30 CFR 36.45 - Quantity of ventilating air.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quantity of ventilating air. 36.45 Section 36... TRANSPORTATION EQUIPMENT Test Requirements § 36.45 Quantity of ventilating air. (a) Results of the engine tests shall be used to calculate ventilation (cubic feet of air per minute) that shall be supplied by positive...

  14. 48 CFR 245.7309-8 - Variations in quantity or weight.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Inventory 245.7309-8 Variations in quantity or weight. When property is sold on a “unit price” basis, the Contractor reserves the right to vary by up to 15 percent the quantity or weight listed in the Invitation and... price shall be adjusted in accordance with the unit price and on the basis of the quantity or weight...

  15. Recognizing Prefixes in Scientific Quantities

    NASA Astrophysics Data System (ADS)

    Sokolowski, Andrzej

    2015-09-01

    Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to meters." Similar students' mistakes were reported also by AP Chemistry readers "as in previous years, students still had difficulty converting kJ to J." While traditional teaching focuses on memorizing the symbols of prefixes, little attention is given to helping learners recognize a prefix in a given quantity. I noticed in my teaching practice that by making the processes of identifying prefixes more explicit, students make fewer mistakes on unit conversion. Thus, this paper presents an outline of a lesson that focuses on prefix recognition. It is designed for a first-year college physics class; however, its key points can be addressed to any group of physics students.

  16. 7 CFR 929.14 - Marketable quantity.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

  17. 7 CFR 929.14 - Marketable quantity.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

  18. 7 CFR 929.14 - Marketable quantity.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

  19. 7 CFR 929.14 - Marketable quantity.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

  20. 7 CFR 929.14 - Marketable quantity.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

  1. Dynamic Segmentation Of Behavior Patterns Based On Quantity Value Movement Using Fuzzy Subtractive Clustering Method

    NASA Astrophysics Data System (ADS)

    Sangadji, Iriansyah; Arvio, Yozika; Indrianto

    2018-03-01

    to understand by analyzing the pattern of changes in value movements that can dynamically vary over a given period with relative accuracy, an equipment is required based on the utilization of technical working principles or specific analytical method. This will affect the level of validity of the output that will occur from this system. Subtractive clustering is based on the density (potential) size of data points in a space (variable). The basic concept of subtractive clustering is to determine the regions in a variable that has high potential for the surrounding points. In this paper result is segmentation of behavior pattern based on quantity value movement. It shows the number of clusters is formed and that has many members.

  2. Recognizing Prefixes in Scientific Quantities

    ERIC Educational Resources Information Center

    Sokolowski, Andrzej

    2015-01-01

    Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to…

  3. Recent advances in approximation concepts for optimum structural design

    NASA Technical Reports Server (NTRS)

    Barthelemy, Jean-Francois M.; Haftka, Raphael T.

    1991-01-01

    The basic approximation concepts used in structural optimization are reviewed. Some of the most recent developments in that area since the introduction of the concept in the mid-seventies are discussed. The paper distinguishes between local, medium-range, and global approximations; it covers functions approximations and problem approximations. It shows that, although the lack of comparative data established on reference test cases prevents an accurate assessment, there have been significant improvements. The largest number of developments have been in the areas of local function approximations and use of intermediate variable and response quantities. It also appears that some new methodologies are emerging which could greatly benefit from the introduction of new computer architecture.

  4. 48 CFR 52.217-6 - Option for Increased Quantity.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Option for Increased....217-6 Option for Increased Quantity. As prescribed in 17.208(d), insert a clause substantially the same as the following: Option for Increased Quantity (MAR 1989) The Government may increase the...

  5. 41 CFR 109-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

  6. 41 CFR 109-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

  7. 41 CFR 109-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

  8. 41 CFR 109-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

  9. 41 CFR 109-27.102 - Economic order quantity principle.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

  10. Visual Working Memory Cannot Trade Quantity for Quality.

    PubMed

    Ramaty, Ayelet; Luria, Roy

    2018-01-01

    Two main models have been proposed to describe how visual working memory (WM) allocates its capacity: the slot-model and the continuous resource-model. The purpose of the current study was to test a direct prediction of the resource model suggesting that WM can trade-off between the quantity and quality of the encoded information. Previous research reported equivocal results, with studies that failed to find such a trade-off and other studies that reported a trade-off. Following the design of previous studies, in Experiment 1 we replicated this trade-off, by presenting the memory array for 1200 ms. Experiment 2 failed to observe a trade-off between quantity and quality using a memory array interval of 300 ms (a standard interval for visual WM). Experiment 3 again failed to find this trade-off, when reinstating the 1200 ms memory array interval but adding an articulatory suppression manipulation. We argue that while participants can trade quantity for quality, this pattern depends on verbal encoding and transfer to long-term memory processes that were possible to perform only during the long retention interval. When these processes were eliminated, the trade-off disappeared. Thus, we didn't find any evidence that the trade-off between quantity for quality can occur within visual WM.

  11. Photosynthesis-related quantities for education and modeling.

    PubMed

    Antal, Taras K; Kovalenko, Ilya B; Rubin, Andrew B; Tyystjärvi, Esa

    2013-11-01

    A quantitative understanding of the photosynthetic machinery depends largely on quantities, such as concentrations, sizes, absorption wavelengths, redox potentials, and rate constants. The present contribution is a collection of numbers and quantities related mainly to photosynthesis in higher plants. All numbers are taken directly from a literature or database source and the corresponding reference is provided. The numerical values, presented in this paper, provide ranges of values, obtained in specific experiments for specific organisms. However, the presented numbers can be useful for understanding the principles of structure and function of photosynthetic machinery and for guidance of future research.

  12. Lecturer Quality, Quantity and Gender in Colleges of Education in Nigeria

    ERIC Educational Resources Information Center

    Arubayi, D. O.

    2009-01-01

    The quality and quantity of lecturers in Tertiary institutions to a great extent determines the quality of graduates. To ensure quality and quantity the Colleges of Education in Nigeria have established internal and external mechanisms. Quantity is determined by the number of students to a given lecturer. Despite the mechanism put forward to…

  13. 10 CFR 40.13 - Unimportant quantities of source material.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Unimportant quantities of source material. 40.13 Section 40.13 Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF SOURCE MATERIAL Exemptions § 40.13 Unimportant quantities of source material. (a) Any person is exempt from the regulations in this part and from...

  14. 10 CFR 40.22 - Small quantities of source material.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Small quantities of source material. 40.22 Section 40.22 Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF SOURCE MATERIAL General Licenses § 40.22 Small quantities of source material. (a) A general license is hereby issued authorizing commercial and industrial...

  15. Processing Ordinality and Quantity: The Case of Developmental Dyscalculia

    PubMed Central

    Rubinsten, Orly; Sury, Dana

    2011-01-01

    In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made “ordered” or “non-ordered” judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information. PMID:21935374

  16. Processing ordinality and quantity: the case of developmental dyscalculia.

    PubMed

    Rubinsten, Orly; Sury, Dana

    2011-01-01

    In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

  17. 16 CFR 500.7 - Net quantity of contents, method of expression.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Net quantity of contents, method of... REGULATIONS UNDER SECTION 4 OF THE FAIR PACKAGING AND LABELING ACT § 500.7 Net quantity of contents, method of expression. The net quantity of contents shall be expressed in terms of weight or mass, measure, numerical...

  18. 77 FR 43077 - Federal Acquisition Regulation; Information Collection; Economic Purchase Quantity-Supplies

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-23

    ...; Information Collection; Economic Purchase Quantity--Supplies AGENCIES: Department of Defense (DOD), General... collection requirement concerning Economic Purchase Quantity--Supplies. Public comments are particularly...: Submit comments identified by Information Collection 9000- 0082, Economic Purchase Quantity--Supplies, by...

  19. The Ordering Challenge: An Online Game to Introduce Independent Demand Inventory Concepts

    ERIC Educational Resources Information Center

    Meyer, Brad C.; Bishop, Debra S.

    2011-01-01

    Students are put in the role of a manager who watches inventory levels decrease and must order at the right time and in the right quantity to minimize costs. This interactive game requires the students to race against time and has levels of increasing difficulty. It introduces the students to the concepts of holding cost, ordering cost, backlog…

  20. A conserved quantity in thin body dynamics

    NASA Astrophysics Data System (ADS)

    Hanna, James; Pendar, Hodjat

    We use an example from textile processing to illustrate the utility of a conserved quantity associated with metric symmetry in a thin body. This quantity, when combined with the usual linear and angular momentum currents, allows us to construct a four-parameter family of curves representing the equilibria of a rotating, flowing string. To achieve this, we introduce a non-material action of mixed Lagrangian-Eulerian type, applicable to fixed windows of axially-moving systems. We will point out intriguing similarities with Bernoulli's equation, discuss the effects of axial flow on rotating conservative systems, and make connections with 19th- and 20th-century results on the dynamics of cables.

  1. 46 CFR 95.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

  2. 46 CFR 76.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 3 2013-10-01 2013-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

  3. 46 CFR 76.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 3 2012-10-01 2012-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

  4. 46 CFR 76.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 3 2014-10-01 2014-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

  5. 46 CFR 76.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

  6. 46 CFR 76.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 3 2011-10-01 2011-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

  7. 46 CFR 95.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

  8. 46 CFR 95.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

  9. 46 CFR 95.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

  10. 46 CFR 95.17-5 - Quantity of foam required.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

  11. A geochemical module for "AMDTreat" to compute caustic quantity, effluent quantity, and sludge volume

    USGS Publications Warehouse

    Cravotta, Charles A.; Parkhurst, David L.; Means, Brent P; McKenzie, Bob; Morris, Harry; Arthur, Bill

    2010-01-01

    Treatment with caustic chemicals typically is used to increase pH and decrease concentrations of dissolved aluminum, iron, and/or manganese in largevolume, metal-laden discharges from active coal mines. Generally, aluminum and iron can be removed effectively at near-neutral pH (6 to 8), whereas active manganese removal requires treatment to alkaline pH (~10). The treatment cost depends on the specific chemical used (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) and increases with the quantities of chemical added and sludge produced. The pH and metals concentrations do not change linearly with the amount of chemical added. Consequently, the amount of caustic chemical needed to achieve a target pH and the corresponding effluent composition and sludge volume can not be accurately determined without empirical titration data or the application of geochemical models to simulate the titration of the discharge water with caustic chemical(s). The AMDTreat computer program (http://amd.osmre.gov/ ) is widely used to compute costs for treatment of coal-mine drainage. Although AMDTreat can use results of empirical titration with industrial grade caustic chemicals to compute chemical costs for treatment of net-acidic or net-alkaline mine drainage, such data are rarely available. To improve the capability of AMDTreat to estimate (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the concentrations of dissolved metals in treated effluent, and (3) the volume of sludge produced by the treatment, a titration simulation is being developed using the geochemical program PHREEQC (wwwbrr.cr.usgs.gov/projects/GWC_coupled/phreeqc/) that will be coupled as a module to AMDTreat. The simulated titration results can be compared with or used in place of empirical titration data to estimate chemical quantities and costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module for AMDTreat.

  12. A Generalized Pivotal Quantity Approach to Analytical Method Validation Based on Total Error.

    PubMed

    Yang, Harry; Zhang, Jianchun

    2015-01-01

    The primary purpose of method validation is to demonstrate that the method is fit for its intended use. Traditionally, an analytical method is deemed valid if its performance characteristics such as accuracy and precision are shown to meet prespecified acceptance criteria. However, these acceptance criteria are not directly related to the method's intended purpose, which is usually a gurantee that a high percentage of the test results of future samples will be close to their true values. Alternate "fit for purpose" acceptance criteria based on the concept of total error have been increasingly used. Such criteria allow for assessing method validity, taking into account the relationship between accuracy and precision. Although several statistical test methods have been proposed in literature to test the "fit for purpose" hypothesis, the majority of the methods are not designed to protect the risk of accepting unsuitable methods, thus having the potential to cause uncontrolled consumer's risk. In this paper, we propose a test method based on generalized pivotal quantity inference. Through simulation studies, the performance of the method is compared to five existing approaches. The results show that both the new method and the method based on β-content tolerance interval with a confidence level of 90%, hereafter referred to as the β-content (0.9) method, control Type I error and thus consumer's risk, while the other existing methods do not. It is further demonstrated that the generalized pivotal quantity method is less conservative than the β-content (0.9) method when the analytical methods are biased, whereas it is more conservative when the analytical methods are unbiased. Therefore, selection of either the generalized pivotal quantity or β-content (0.9) method for an analytical method validation depends on the accuracy of the analytical method. It is also shown that the generalized pivotal quantity method has better asymptotic properties than all of the current

  13. Radiation Protection Quantities for Near Earth Environments

    NASA Technical Reports Server (NTRS)

    Clowdsley, Martha S.; Wilson, John W.; Kim, Myung-Hee; Anderson, Brooke M.; Nealy, John E.

    2004-01-01

    As humans travel beyond the protection of the Earth's magnetic field and mission durations grow, risk due to radiation exposure will increase and may become the limiting factor for such missions. Here, the dosimetric quantities recommended by the National Council on Radiation Protection and Measurements (NCRP) for the evaluation of health risk due to radiation exposure, effective dose and gray-equivalent to eyes, skin, and blood forming organs (BFO), are calculated for several near Earth environments. These radiation protection quantities are evaluated behind two different shielding materials, aluminum and polyethylene. Since exposure limits for missions beyond low Earth orbit (LEO) have not yet been defined, results are compared to limits recommended by the NCRP for LEO operations.

  14. Micro-Costing Quantity Data Collection Methods

    PubMed Central

    Frick, Kevin D.

    2009-01-01

    Background Micro-costing studies collect detailed data on resources utilized and the value of those resources. Such studies are useful for estimating the cost of new technologies or new community-based interventions, for producing estimates in studies that include non-market goods, and for studying within-procedure cost variation. Objectives This objectives of this paper were to (1) describe basic micro-costing methods focusing on quantity data collection; and (2) suggest a research agenda to improve methods in and the interpretation of micro-costing Research Design Examples in the published literature were used to illustrate steps in the methods of gathering data (primarily quantity data) for a micro-costing study. Results Quantity data collection methods that were illustrated in the literature include the use of (1) administrative databases at single facilities, (2) insurer administrative data, (3) forms applied across multiple settings, (4) an expert panel, (5) surveys or interviews of one or more types of providers; (6) review of patient charts, (7) direct observation, (8) personal digital assistants, (9) program operation logs, and (10) diary data. Conclusions Future micro-costing studies are likely to improve if research is done to compare the validity and cost of different data collection methods; if a critical review is conducted of studies done to date; and if the combination of the results of the first two steps described are used to develop guidelines that address common limitations, critical judgment points, and decisions that can reduce limitations and improve the quality of studies. PMID:19536026

  15. 7 CFR 1435.303 - Adjustment of the overall allotment quantity.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

  16. 7 CFR 1435.303 - Adjustment of the overall allotment quantity.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

  17. 7 CFR 1435.303 - Adjustment of the overall allotment quantity.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

  18. 7 CFR 1435.303 - Adjustment of the overall allotment quantity.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

  19. 7 CFR 1435.303 - Adjustment of the overall allotment quantity.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

  20. Seasoning small quantities of lumber

    Treesearch

    E.F. Rasmussen

    1965-01-01

    The owner of a small quantity of green lumber or logs is often confronted with seasoning it to a state of dryness suitable for use in furniture, wood carving, or other handiwork. He cannot follow the practice of commercial mills, which employ dry kilns for the purpose. because kilns are too costly. On the other hand, air seasoning outdoors usually does not dry lumber...

  1. 7 CFR 35.13 - Minimum quantity.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Minimum quantity. 35.13 Section 35.13 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... part, transport or receive for transportation to any foreign destination, a shipment of 25 packages or...

  2. Simulated wetland conservation-restoration effects on water quantity and quality at watershed scale.

    PubMed

    Wang, Xixi; Shang, Shiyou; Qu, Zhongyi; Liu, Tingxi; Melesse, Assefa M; Yang, Wanhong

    2010-07-01

    Wetlands are one of the most important watershed microtopographic features that affect hydrologic processes (e.g., routing) and the fate and transport of constituents (e.g., sediment and nutrients). Efforts to conserve existing wetlands and/or to restore lost wetlands require that watershed-level effects of wetlands on water quantity and water quality be quantified. Because monitoring approaches are usually cost or logistics prohibitive at watershed scale, distributed watershed models such as the Soil and Water Assessment Tool (SWAT), enhanced by the hydrologic equivalent wetland (HEW) concept developed by Wang [Wang, X., Yang, W., Melesse, A.M., 2008. Using hydrologic equivalent wetland concept within SWAT to estimate streamflow in watersheds with numerous wetlands. Trans. ASABE 51 (1), 55-72.], can be a best resort. However, there is a serious lack of information about simulated effects using this kind of integrated modeling approach. The objective of this study was to use the HEW concept in SWAT to assess effects of wetland restoration within the Broughton's Creek watershed located in southwestern Manitoba, and of wetland conservation within the upper portion of the Otter Tail River watershed located in northwestern Minnesota. The results indicated that the HEW concept allows the nonlinear functional relations between watershed processes and wetland characteristics (e.g., size and morphology) to be accurately represented in the models. The loss of the first 10-20% of the wetlands in the Minnesota study area would drastically increase the peak discharge and loadings of sediment, total phosphorus (TP), and total nitrogen (TN). On the other hand, the justifiable reductions of the peak discharge and loadings of sediment, TP, and TN in the Manitoba study area may require that 50-80% of the lost wetlands be restored. Further, the comparison between the predicted restoration and conservation effects revealed that wetland conservation seems to deserve a higher priority

  3. Quantities for assessing high photon doses to the body: a calculational approach.

    PubMed

    Eakins, Jonathan S; Ainsbury, Elizabeth A

    2018-06-01

    Tissue reactions are the most clinically significant consequences of high-dose exposures to ionising radiation. However, currently there is no universally recognized dose quantity that can be used to assess and report generalised risks to individuals following whole body exposures in the high-dose range. In this work, a number of potential dose quantities are presented and discussed, with mathematical modelling techniques employed to compare them and explore when their differences are most or least manifest. The results are interpreted to propose the average (D GRB ) of the absorbed doses to the stomach, small intestine, red bone marrow, and brain as the optimum quantity for informing assessments of risk. A second, maximally conservative dose quantity (D Max ) is also suggested, which places limits on any under-estimates resulting from the adoption of D GRB . The primary aim of this work is to spark debate, with further work required to refine the final choice of quantity or quantities most appropriate for the full range of different potential exposure scenarios.

  4. Expressions for IAU 2000 precession quantities

    NASA Astrophysics Data System (ADS)

    Capitaine, N.; Wallace, P. T.; Chapront, J.

    2003-12-01

    A new precession-nutation model for the Celestial Intermediate Pole (CIP) was adopted by the IAU in 2000 (Resolution B1.6). The model, designated IAU 2000A, includes a nutation series for a non-rigid Earth and corrections for the precession rates in longitude and obliquity. The model also specifies numerical values for the pole offsets at J2000.0 between the mean equatorial frame and the Geocentric Celestial Reference System (GCRS). In this paper, we discuss precession models consistent with IAU 2000A precession-nutation (i.e. MHB 2000, provided by Mathews et al. \\cite{Mathews02}) and we provide a range of expressions that implement them. The final precession model, designated P03, is a possible replacement for the precession component of IAU 2000A, offering improved dynamical consistency and a better basis for future improvement. As a preliminary step, we present our expressions for the currently used precession quantities zetaA, thetaA, zA, in agreement with the MHB corrections to the precession rates, that appear in the IERS Conventions 2000. We then discuss a more sophisticated method for improving the precession model of the equator in order that it be compliant with the IAU 2000A model. In contrast to the first method, which is based on corrections to the t terms of the developments for the precession quantities in longitude and obliquity, this method also uses corrections to their higher degree terms. It is essential that this be used in conjunction with an improved model for the ecliptic precession, which is expected, given the known discrepancies in the IAU 1976 expressions, to contribute in a significant way to these higher degree terms. With this aim in view, we have developed new expressions for the motion of the ecliptic with respect to the fixed ecliptic using the developments from Simon et al. (\\cite{Simon94}) and Williams (\\cite{Williams94}) and with improved constants fitted to the most recent numerical planetary ephemerides. We have then used

  5. 19 CFR 132.5 - Merchandise imported in excess of quota quantities.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... quantities. (a) Absolute quota merchandise. Absolute quota merchandise imported in excess of the quantity... merchandise. Merchandise imported in excess of either an absolute or a tariff-rate quota may be held for the...

  6. 19 CFR 132.5 - Merchandise imported in excess of quota quantities.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... quantities. (a) Absolute quota merchandise. Absolute quota merchandise imported in excess of the quantity... merchandise. Merchandise imported in excess of either an absolute or a tariff-rate quota may be held for the...

  7. Association between work-family conflict and smoking quantity among daily smokers.

    PubMed

    Macy, Jonathan T; Chassin, Laurie; Presson, Clark C

    2013-11-01

    Recent work demonstrated a direct relation between work-family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work-family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors.

  8. 48 CFR 16.504 - Indefinite-quantity contracts.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... quantity based on market research, trends on recent contracts for similar supplies or services, survey of... are unique or highly specialized; (2) Based on the contracting officer's knowledge of the market, more...

  9. 14 CFR 29.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Placards § 29.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or... extending from the calibrated zero reading to the lowest reading obtainable in level flight. ...

  10. 14 CFR 25.1553 - Fuel quantity indicator.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Placards § 25.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or... extending from the calibrated zero reading to the lowest reading obtainable in level flight. ...

  11. Method and Apparatus for Measuring Radiation Quantities

    DOEpatents

    Roberts, N O

    1955-01-25

    This patent application describes a compact dosimeter for measuring X-ray and gamma radiation by the use of solutions which undergo a visible color change upon exposure to a predetermined quantity of radiation.

  12. Combined quantity management and biological treatment of sludge liquor at Hamburg's wastewater treatment plants--first experience in operation with the Store and Treat process.

    PubMed

    Laurich, F

    2004-01-01

    Store and Treat (SAT) is a new concept for the management of ammonium-rich process waste waters at wastewater treatment plants. It combines the advantages of quantity management and separate biological treatment, whereby both operations are carried out in the same tank. Now the first full-scale application of that method was realized in Hamburg. As first experience shows the process can help to increase nitrogen removal and to reduce energy consumption.

  13. How tobacco companies have used package quantity for consumer targeting.

    PubMed

    Persoskie, Alexander; Donaldson, Elisabeth A; Ryant, Chase

    2018-05-31

    Package quantity refers to the number of cigarettes or amount of other tobacco product in a package. Many countries restrict minimum cigarette package quantities to avoid low-cost packs that may lower barriers to youth smoking. We reviewed Truth Tobacco Industry Documents to understand tobacco companies' rationales for introducing new package quantities, including companies' expectations and research regarding how package quantity may influence consumer behaviour. A snowball sampling method (phase 1), a static search string (phase 2) and a follow-up snowball search (phase 3) identified 216 documents, mostly from the 1980s and 1990s, concerning cigarettes (200), roll-your-own tobacco (9), smokeless tobacco (6) and 'smokeless cigarettes' (1). Companies introduced small and large packages to motivate brand-switching and continued use among current users when faced with low market share or threats such as tax-induced price increases or competitors' use of price promotions. Companies developed and evaluated package quantities for specific brands and consumer segments. Large packages offered value-for-money and matched long-term, heavy users' consumption rates. Small packages were cheaper, matched consumption rates of newer and lighter users, and increased products' novelty, ease of carrying and perceived freshness. Some users also preferred small packages as a way to try to limit consumption or quit. Industry documents speculated about many potential effects of package quantity on appeal and use, depending on brand and consumer segment. The search was non-exhaustive, and we could not assess the quality of much of the research or other information on which the documents relied. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  14. 21 CFR 701.13 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... (CONTINUED) COSMETICS COSMETIC LABELING Package Form § 701.13 Declaration of net quantity of contents. (a) The label of a cosmetic in package form shall bear a declaration of the net quantity of contents. This... weight or measure. The statement shall be in terms of fluid measure if the cosmetic is liquid or in terms...

  15. Consumer-Resource Dynamics: Quantity, Quality, and Allocation

    PubMed Central

    Getz, Wayne M.; Owen-Smith, Norman

    2011-01-01

    Background The dominant paradigm for modeling the complexities of interacting populations and food webs is a system of coupled ordinary differential equations in which the state of each species, population, or functional trophic group is represented by an aggregated numbers-density or biomass-density variable. Here, using the metaphysiological approach to model consumer-resource interactions, we formulate a two-state paradigm that represents each population or group in a food web in terms of both its quantity and quality. Methodology and Principal Findings The formulation includes an allocation function controlling the relative proportion of extracted resources to increasing quantity versus elevating quality. Since lower quality individuals senesce more rapidly than higher quality individuals, an optimal allocation proportion exists and we derive an expression for how this proportion depends on population parameters that determine the senescence rate, the per-capita mortality rate, and the effects of these rates on the dynamics of the quality variable. We demonstrate that oscillations do not arise in our model from quantity-quality interactions alone, but require consumer-resource interactions across trophic levels that can be stabilized through judicious resource allocation strategies. Analysis and simulations provide compelling arguments for the necessity of populations to evolve quality-related dynamics in the form of maternal effects, storage or other appropriate structures. They also indicate that resource allocation switching between investments in abundance versus quality provide a powerful mechanism for promoting the stability of consumer-resource interactions in seasonally forcing environments. Conclusions/Significance Our simulations show that physiological inefficiencies associated with this switching can be favored by selection due to the diminished exposure of inefficient consumers to strong oscillations associated with the well-known paradox of

  16. The effects of quantity and depth of processing on children's time perception.

    PubMed

    Arlin, M

    1986-08-01

    Two experiments were conducted to investigate the effects of quantity and depth of processing on children's time perception. These experiments tested the appropriateness of two adult time-perception models (attentional and storage size) for younger ages. Children were given stimulus sets of equal time which varied by level of processing (deep/shallow) and quantity (list length). In the first experiment, 28 children in Grade 6 reproduced presentation times of various quantities of pictures under deep (living/nonliving categorization) or shallow (repeating label) conditions. Students also compared pairs of durations. In the second experiment, 128 children in Grades K, 2, 4, and 6 reproduced presentation times under similar conditions with three or six pictures and with deep or shallow processing requirements. Deep processing led to decreased estimation of time. Higher quantity led to increased estimation of time. Comparative judgments were influenced by quantity. The interaction between age and depth of processing was significant. Older children were more affected by depth differences than were younger children. Results were interpreted as supporting different aspects of each adult model as explanations of children's time perception. The processing effect supported the attentional model and the quantity effect supported the storage size model.

  17. Association Between Work–Family Conflict and Smoking Quantity Among Daily Smokers

    PubMed Central

    2013-01-01

    Introduction: Recent work demonstrated a direct relation between work–family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work–family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Methods: Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Results: Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. Conclusions: After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors. PMID:23709611

  18. Varieties of Quantity Estimation in Children

    ERIC Educational Resources Information Center

    Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

    2015-01-01

    In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3…

  19. 7 CFR 966.53 - Minimum quantities.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Minimum quantities. 966.53 Section 966.53 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... will be free from regulations issued or effective pursuant to §§ 966.42, 966.52, 966.54, 966.60, or any...

  20. Memory for Multiple Cache Locations and Prey Quantities in a Food-Hoarding Songbird

    PubMed Central

    Armstrong, Nicola; Garland, Alexis; Burns, K. C.

    2012-01-01

    Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes), a food-hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with (1) the number of cache sites containing prey rewards and (2) the length of time separating cache creation and retrieval (retention interval). Results showed that subjects generally performed above-chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3, and 4 cache sites from between 1, 10, and 60 s. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to 1 min long retention intervals without training. PMID:23293622

  1. Memory for multiple cache locations and prey quantities in a food-hoarding songbird.

    PubMed

    Armstrong, Nicola; Garland, Alexis; Burns, K C

    2012-01-01

    Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes), a food-hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with (1) the number of cache sites containing prey rewards and (2) the length of time separating cache creation and retrieval (retention interval). Results showed that subjects generally performed above-chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3, and 4 cache sites from between 1, 10, and 60 s. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to 1 min long retention intervals without training.

  2. Arsenic Treatment Residuals: Quantities, Characteristics and Disposal

    EPA Science Inventory

    This presentation provides information on the quantities, the characteristics and the disposal options for the common arsenic removal technologies. The technologies consist of adsorption media, iron removal, coagulation/filtration and ion exchange. The information for the prese...

  3. Enhancing Least-Squares Finite Element Methods Through a Quantity-of-Interest

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chaudhry, Jehanzeb Hameed; Cyr, Eric C.; Liu, Kuo

    2014-12-18

    Here, we introduce an approach that augments least-squares finite element formulations with user-specified quantities-of-interest. The method incorporates the quantity-of-interest into the least-squares functional and inherits the global approximation properties of the standard formulation as well as increased resolution of the quantity-of-interest. We establish theoretical properties such as optimality and enhanced convergence under a set of general assumptions. Central to the approach is that it offers an element-level estimate of the error in the quantity-of-interest. As a result, we introduce an adaptive approach that yields efficient, adaptively refined approximations. Several numerical experiments for a range of situations are presented to supportmore » the theory and highlight the effectiveness of our methodology. Notably, the results show that the new approach is effective at improving the accuracy per total computational cost.« less

  4. Growing Large Quantities of Containerized Seedlings

    Treesearch

    Tim Pittman

    2002-01-01

    The sowing of large quantities of longleaf pine (Pinus palustris Mill.) seed into trays depends on the quality of the seed and the timing of seed sowing. This can be accomplished with mechanization. Seed quality is accomplished by using a gravity table. Tray filling can be accomplished by using a ribbon-type soil mixer and an automated tray-filling...

  5. Infants Make Quantity Discriminations for Substances

    ERIC Educational Resources Information Center

    Hespos, Susan J.; Dora, Begum; Rips, Lance J.; Christie, Stella

    2012-01-01

    Infants can track small groups of solid objects, and infants can respond when these quantities change. But earlier work is equivocal about whether infants can track continuous substances, such as piles of sand. Experiment 1 ("N" = 88) used a habituation paradigm to show infants can register changes in the size of piles of sand that they…

  6. Quantity and unit extraction for scientific and technical intelligence analysis

    NASA Astrophysics Data System (ADS)

    David, Peter; Hawes, Timothy

    2017-05-01

    Scientific and Technical (S and T) intelligence analysts consume huge amounts of data to understand how scientific progress and engineering efforts affect current and future military capabilities. One of the most important types of information S and T analysts exploit is the quantities discussed in their source material. Frequencies, ranges, size, weight, power, and numerous other properties and measurements describing the performance characteristics of systems and the engineering constraints that define them must be culled from source documents before quantified analysis can begin. Automating the process of finding and extracting the relevant quantities from a wide range of S and T documents is difficult because information about quantities and their units is often contained in unstructured text with ad hoc conventions used to convey their meaning. Currently, even simple tasks, such as searching for documents discussing RF frequencies in a band of interest, is a labor intensive and error prone process. This research addresses the challenges facing development of a document processing capability that extracts quantities and units from S and T data, and how Natural Language Processing algorithms can be used to overcome these challenges.

  7. 30 CFR 1206.119 - How are royalty quantity and quality determined?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 3 2013-07-01 2013-07-01 false How are royalty quantity and quality determined? 1206.119 Section 1206.119 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.119 How are royalty quantity and...

  8. 30 CFR 1206.119 - How are royalty quantity and quality determined?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 3 2012-07-01 2012-07-01 false How are royalty quantity and quality determined? 1206.119 Section 1206.119 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.119 How are royalty quantity and...

  9. 30 CFR 1206.119 - How are royalty quantity and quality determined?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 3 2014-07-01 2014-07-01 false How are royalty quantity and quality determined? 1206.119 Section 1206.119 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.119 How are royalty quantity and...

  10. Quantity judgments of sequentially presented food items by capuchin monkeys (Cebus apella).

    PubMed

    Evans, Theodore A; Beran, Michael J; Harris, Emily H; Rice, Daniel F

    2009-01-01

    Recent assessments have shown that capuchin monkeys, like chimpanzees and other Old World primate species, are sensitive to quantitative differences between sets of visible stimuli. In the present study, we examined capuchins' performance in a more sophisticated quantity judgment task that required the ability to form representations of food quantities while viewing the quantities only one piece at a time. In three experiments, we presented monkeys with the choice between two sets of discrete homogeneous food items and allowed the monkeys to consume the set of their choice. In Experiments 1 and 2, monkeys compared an entirely visible food set to a second set, presented item-by-item into an opaque container. All monkeys exhibited high accuracy in choosing the larger set, even when the entirely visible set was presented last, preventing the use of one-to-one item correspondence to compare quantities. In Experiment 3, monkeys compared two sets that were each presented item-by-item into opaque containers, but at different rates to control for temporal cues. Some monkeys performed well in this experiment, though others exhibited near-chance performance, suggesting that this species' ability to form representations of food quantities may be limited compared to previously tested species such as chimpanzees. Overall, these findings support the analog magnitude model of quantity representation as an explanation for capuchin monkeys' quantification of sequentially presented food items.

  11. [Relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii].

    PubMed

    Zhu, Hua; Teng, Jianbei; Cai, Yi; Liang, Jie; Zhu, Yilin; Wei, Tao

    2011-12-01

    To find out the relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii. Microscopy-counting process was applied to starch quantity statistics, sulfuric acid-anthrone colorimetry was used to assay polysaccharides content and bromocresol green colorimetry was used to assay alkaloid content. Pearson product moment correlation analysis, Kendall's rank correlation analysis and Spearman's concordance coefficient analysis were applied to study their relativity. Extremely significant positive correlation was found between starch quantity and polysaccharides content, and significant negative correlation between alkaloid content and starch quantity was discovered, as well was between alkaloid content and polysaccharides content.

  12. Application of sensitivity-analysis techniques to the calculation of topological quantities

    NASA Astrophysics Data System (ADS)

    Gilchrist, Stuart

    2017-08-01

    Magnetic reconnection in the corona occurs preferentially at sites where the magnetic connectivity is either discontinuous or has a large spatial gradient. Hence there is a general interest in computing quantities (like the squashing factor) that characterize the gradient in the field-line mapping function. Here we present an algorithm for calculating certain (quasi)topological quantities using mathematical techniques from the field of ``sensitivity-analysis''. The method is based on the calculation of a three dimensional field-line mapping Jacobian from which all the present topological quantities of interest can be derived. We will present the algorithm and the details of a publicly available set of libraries that implement the algorithm.

  13. 30 CFR 250.458 - What quantities of drilling fluids are required?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 2 2012-07-01 2012-07-01 false What quantities of drilling fluids are required... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling fluids are...

  14. 30 CFR 250.458 - What quantities of drilling fluids are required?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What quantities of drilling fluids are required...

  15. 30 CFR 250.458 - What quantities of drilling fluids are required?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 2 2013-07-01 2013-07-01 false What quantities of drilling fluids are required... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling fluids are...

  16. 30 CFR 250.458 - What quantities of drilling fluids are required?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 2 2014-07-01 2014-07-01 false What quantities of drilling fluids are required... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling fluids are...

  17. Methodology for assessing quantities of water and proppant injection, and water production associated with development of continuous petroleum accumulations

    USGS Publications Warehouse

    Haines, Seth S.

    2015-07-13

    The quantities of water and hydraulic fracturing proppant required for producing petroleum (oil, gas, and natural gas liquids) from continuous accumulations, and the quantities of water extracted during petroleum production, can be quantitatively assessed using a probabilistic approach. The water and proppant assessment methodology builds on the U.S. Geological Survey methodology for quantitative assessment of undiscovered technically recoverable petroleum resources in continuous accumulations. The U.S. Geological Survey assessment methodology for continuous petroleum accumulations includes fundamental concepts such as geologically defined assessment units, and probabilistic input values including well-drainage area, sweet- and non-sweet-spot areas, and success ratio within the untested area of each assessment unit. In addition to petroleum-related information, required inputs for the water and proppant assessment methodology include probabilistic estimates of per-well water usage for drilling, cementing, and hydraulic-fracture stimulation; the ratio of proppant to water for hydraulic fracturing; the percentage of hydraulic fracturing water that returns to the surface as flowback; and the ratio of produced water to petroleum over the productive life of each well. Water and proppant assessments combine information from recent or current petroleum assessments with water- and proppant-related input values for the assessment unit being studied, using Monte Carlo simulation, to yield probabilistic estimates of the volume of water for drilling, cementing, and hydraulic fracture stimulation; the quantity of proppant for hydraulic fracture stimulation; and the volumes of water produced as flowback shortly after well completion, and produced over the life of the well.

  18. Exercise quantity-dependent muscle hypertrophy in adult zebrafish (Danio rerio).

    PubMed

    Hasumura, Takahiro; Meguro, Shinichi

    2016-07-01

    Exercise is very important for maintaining and increasing skeletal muscle mass, and is particularly important to prevent and care for sarcopenia and muscle disuse atrophy. However, the dose-response relationship between exercise quantity, duration/day, and overall duration and muscle mass is poorly understood. Therefore, we investigated the effect of exercise duration on skeletal muscle to reveal the relationship between exercise quantity and muscle hypertrophy in zebrafish forced to exercise. Adult male zebrafish were exercised 6 h/day for 4 weeks, 6 h/day for 2 weeks, or 3 h/day for 2 weeks. Flow velocity was adjusted to maximum velocity during continual swimming (initial 43 cm/s). High-speed consecutive photographs revealed that zebrafish mainly drove the caudal part. Additionally, X-ray micro computed tomography measurements indicated muscle hypertrophy of the mid-caudal half compared with the mid-cranial half part. The cross-sectional analysis of the mid-caudal half muscle revealed that skeletal muscle (red, white, or total) mass increased with increasing exercise quantity, whereas that of white muscle and total muscle increased only under the maximum exercise load condition of 6 h/day for 4 weeks. Additionally, the muscle fiver size distributions of exercised fish were larger than those from non-exercised fish. We revealed that exercise quantity, duration/day, and overall duration were correlated with skeletal muscle hypertrophy. The forced exercise model enabled us to investigate the relationship between exercise quantity and skeletal muscle mass. These results open up the possibility for further investigations on the effects of exercise on skeletal muscle in adult zebrafish.

  19. 48 CFR 816.504 - Indefinite-quantity contracts.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Indefinite-quantity contracts. 816.504 Section 816.504 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS....216-70 in solicitations for bulk coal. (c) The contracting officer shall insert the Alternate II...

  20. 48 CFR 816.504 - Indefinite-quantity contracts.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Indefinite-quantity contracts. 816.504 Section 816.504 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS....216-70 in solicitations for bulk coal. (c) The contracting officer shall insert the Alternate II...

  1. Linear actuation using milligram quantities of CL-20 and TAGDNAT.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Snedigar, Shane; Salton, Jonathan Robert; Tappan, Alexander Smith

    2009-07-01

    There are numerous applications for small-scale actuation utilizing pyrotechnics and explosives. In certain applications, especially when multiple actuation strokes are needed, or actuator reuse is required, it is desirable to have all gaseous combustion products with no condensed residue in the actuator cylinder. Toward this goal, we have performed experiments on utilizing milligram quantities of high explosives to drive a millimeter-diameter actuator with a stroke of 30 mm. Calculations were performed to select proper material quantities to provide 0.5 J of actuation energy. This was performed utilizing the thermochemical code Cheetah to calculate the impetus for numerous propellants and tomore » select quantities based on estimated efficiencies of these propellants at small scales. Milligram quantities of propellants were loaded into a small-scale actuator and ignited with an ignition increment and hot wire ignition. Actuator combustion chamber pressure was monitored with a pressure transducer and actuator stroke was monitored using a laser displacement meter. Total actuation energy was determined by calculating the kinetic energy of reaction mass motion against gravity. Of the materials utilized, the best performance was obtained with a mixture of 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) and bis-triaminoguanidinium(3,3{prime}dinitroazotriazolate) (TAGDNAT).« less

  2. 30 CFR 250.458 - What quantities of drilling fluids are required?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling fluids are required? (a) You must use... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What quantities of drilling fluids are required...

  3. 78 FR 5448 - Federal Acquisition Regulation; Submission for OMB Review; Economic Purchase Quantity-Supplies

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-25

    ...; Submission for OMB Review; Economic Purchase Quantity--Supplies AGENCY: Department of Defense (DOD), General... collection requirement concerning Economic Purchase Quantity--Supplies. A notice was published in the Federal... Information Collection 9000- 0082, Economic Purchase Quantity--Supplies, by any of the following methods...

  4. 46 CFR 76.15-5 - Quantity, pipe sizes, and discharge rate.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 3 2011-10-01 2011-10-01 false Quantity, pipe sizes, and discharge rate. 76.15-5... PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 76.15-5 Quantity, pipe sizes, and... dioxide required for each space in cubic feet shall be equal to the gross volume of the space in cubic...

  5. 46 CFR 34.17-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 1 2011-10-01 2011-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

  6. 46 CFR 34.17-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 1 2014-10-01 2014-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

  7. 46 CFR 34.17-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 1 2012-10-01 2012-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

  8. 46 CFR 34.17-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 1 2013-10-01 2013-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

  9. 46 CFR 34.17-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

  10. Explosion Hazards Associated with Spills of Large Quantities of Hazardous Materials. Phase I

    DTIC Science & Technology

    1974-10-01

    quantities of hazardous material such as liquified natural gas ( LNG ), liquified petroleum gils (LPG), or ethylene. The principal results are (1) a...associated with spills of large quantities of hazardous material such as liquified natural gas ( LNG ), liquified petroleum gas (LPG), or ethylene. The...liquified natural gas ( LNG ). Unfortunately, as the quantity of material shipped at one time increases, so does the potential hazard associated with

  11. Observable quantities for electrodiffusion processes in membranes.

    PubMed

    Garrido, Javier

    2008-03-13

    Electrically driven ion transport processes in a membrane system are analyzed in terms of observable quantities, such as the apparent volume flow, the time dependence of the electrolyte concentration in one cell compartment, and the electrical potential difference between the electrodes. The relations between the fluxes and these observable quantities are rigorously deduced from balances for constituent mass and solution volume. These relations improve the results for the transport coefficients up to 25% with respect to those obtained using simplified expressions common in the literature. Given the practical importance of ionic transport numbers and the solvent transference number in the phenomenological description of electrically driven processes, the transport equations are presented using the electrolyte concentration difference and the electric current as the drivers of the different constituents. Because various electric potential differences can be used in this traditional irreversible thermodynamics approach, the advantages of the formulation of the transport equations in terms of concentration difference and electric current are emphasized.

  12. Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores

    PubMed Central

    Fukunaga, Gaku; Takayasu, Hideki; Takayasu, Misako

    2016-01-01

    The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor’s law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases. PMID:27310915

  13. Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

    PubMed

    Fukunaga, Gaku; Takayasu, Hideki; Takayasu, Misako

    2016-01-01

    The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

  14. A small quantity of sodium arsenite will kill large cull hardwoods

    Treesearch

    Francis M. Rushmore

    1956-01-01

    Although it is well known that sodium arsenite is an effective silvicide, forestry literature contains little information about the minimum quantities of this chemical that are required to kill large cull trees. Such information would be of value because if small quantities of a chemical will produce satisfactory results, small holes or frills in the tree will hold it...

  15. 46 CFR 34.20-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 1 2011-10-01 2011-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Deck Foam System, Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed...

  16. Quantity Representation in Children and Rhesus Monkeys: Linear Versus Logarithmic Scales

    ERIC Educational Resources Information Center

    Beran, Michael J.; Johnson-Pynn, Julie S.; Ready, Christopher

    2008-01-01

    The performances of 4- and 5-year-olds and rhesus monkeys were compared using a computerized task for quantity assessment. Participants first learned two quantity anchor values and then responded to intermediate values by classifying them as similar to either the large anchor or the small anchor. Of primary interest was an assessment of where the…

  17. Thrust augmentation nozzle (TAN) concept for rocket engine booster applications

    NASA Astrophysics Data System (ADS)

    Forde, Scott; Bulman, Mel; Neill, Todd

    2006-07-01

    Aerojet used the patented thrust augmented nozzle (TAN) concept to validate a unique means of increasing sea-level thrust in a liquid rocket booster engine. We have used knowledge gained from hypersonic Scramjet research to inject propellants into the supersonic region of the rocket engine nozzle to significantly increase sea-level thrust without significantly impacting specific impulse. The TAN concept overcomes conventional engine limitations by injecting propellants and combusting in an annular region in the divergent section of the nozzle. This injection of propellants at moderate pressures allows for obtaining high thrust at takeoff without overexpansion thrust losses. The main chamber is operated at a constant pressure while maintaining a constant head rise and flow rate of the main propellant pumps. Recent hot-fire tests have validated the design approach and thrust augmentation ratios. Calculations of nozzle performance and wall pressures were made using computational fluid dynamics analyses with and without thrust augmentation flow, resulting in good agreement between calculated and measured quantities including augmentation thrust. This paper describes the TAN concept, the test setup, test results, and calculation results.

  18. Uncertainty analysis of thermal quantities measurement in a centrifugal compressor

    NASA Astrophysics Data System (ADS)

    Hurda, Lukáš; Matas, Richard

    2017-09-01

    Compressor performance characteristics evaluation process based on the measurement of pressure, temperature and other quantities is examined to find uncertainties for directly measured and derived quantities. CFD is used as a tool to quantify the influences of different sources of uncertainty of measurements for single- and multi-thermocouple total temperature probes. The heat conduction through the body of the thermocouple probe and the heat-up of the air in the intake piping are the main phenomena of interest.

  19. 49 CFR 173.4a - Excepted quantities.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... of withstanding without leakage the pressure differential specified in § 173.27(c) of this part. (b... ice), and lithium batteries and cells. (c) Inner packaging limits. The maximum quantity of hazardous..., rigid outer packaging. (5) Placement of the material in the package or packing different materials in...

  20. CALL, Prewriting Strategies, and EFL Writing Quantity

    ERIC Educational Resources Information Center

    Shafiee, Sajad; Koosha, Mansour; Afghar, Akbar

    2015-01-01

    This study sought to explore the effect of teaching prewriting strategies through different methods of input delivery (i.e. conventional, web-based, and hybrid) on EFL learners' writing quantity. In its quasi-experimental study, the researchers recruited 98 available sophomores, and assigned them to three experimental groups (conventional,…

  1. 7 CFR 945.54 - Minimum quantity exemption.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Minimum quantity exemption. 945.54 Section 945.54 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... regulations issued or in effect pursuant to §§ 945.40 to 945.65, inclusive, or any combination thereof. ...

  2. Automated Decisional Model for Optimum Economic Order Quantity Determination Using Price Regressive Rates

    NASA Astrophysics Data System (ADS)

    Roşu, M. M.; Tarbă, C. I.; Neagu, C.

    2016-11-01

    The current models for inventory management are complementary, but together they offer a large pallet of elements for solving complex problems of companies when wanting to establish the optimum economic order quantity for unfinished products, row of materials, goods etc. The main objective of this paper is to elaborate an automated decisional model for the calculus of the economic order quantity taking into account the price regressive rates for the total order quantity. This model has two main objectives: first, to determine the periodicity when to be done the order n or the quantity order q; second, to determine the levels of stock: lighting control, security stock etc. In this way we can provide the answer to two fundamental questions: How much must be ordered? When to Order? In the current practice, the business relationships with its suppliers are based on regressive rates for price. This means that suppliers may grant discounts, from a certain level of quantities ordered. Thus, the unit price of the products is a variable which depends on the order size. So, the most important element for choosing the optimum for the economic order quantity is the total cost for ordering and this cost depends on the following elements: the medium price per units, the stock cost, the ordering cost etc.

  3. 16 CFR 1.23 - Quantity limit rules.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Quantity limit rules. 1.23 Section 1.23 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE GENERAL... Robinson-Patman Act. These rules have the force and effect of law. [32 FR 8444, June 13, 1967. Redesignated...

  4. 46 CFR 34.20-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 1 2012-10-01 2012-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

  5. 46 CFR 34.20-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 1 2013-10-01 2013-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

  6. 46 CFR 34.20-5 - Quantity of foam required-T/ALL.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 1 2014-10-01 2014-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

  7. Urgency of increasing the quantity and quality of student creativity program

    NASA Astrophysics Data System (ADS)

    Sarmini; Prasetya, Ketut; Nadiroh, Ulin

    2018-01-01

    Student creativity is very important to improve the quality and quantity. The purpose of this paper is to identify the quality and quantity of the Student Creativity Program. The method in this research is exploratory study. The subjects taken are the leaders of deans and vice deans at the State University of Surabaya. Data collection techniques used are kusioner. The result of this research is creativity program in student is very important. Not only improve the quality and quantity of creativity, but also affect the image of the institution. It is necessary to have written rules on the regulations on the Student Creativity Program and to take a comprehensive and comprehensive approach, and to organize the budget is the main thing.

  8. Conservation laws and conserved quantities for (1+1)D linearized Boussinesq equations

    NASA Astrophysics Data System (ADS)

    Carvalho, Cindy; Harley, Charis

    2017-05-01

    Conservation laws and physical conserved quantities for the (1+1)D linearized Boussinesq equations at a constant water depth are presented. These equations describe incompressible, inviscid, irrotational fluid flow in the form of a non steady solitary wave. A systematic multiplier approach is used to obtain the conservation laws of the system of third order partial differential equations (PDEs) in dimensional form. Physical conserved quantities are derived by integrating the conservation laws in the direction of wave propagation and imposing decaying boundary conditions in the horizontal direction. One of these is a newly discovered conserved quantity which relates to an energy flux density.

  9. Regulation of Black Pepper Inflorescence Quantity by Shading at Different Growth Stages.

    PubMed

    Zu, Chao; Wu, Guiping; Li, Zhigang; Yang, Jianfeng; Wang, Can; Yu, Huan; Wu, Huasong

    2016-07-01

    Black pepper is a perennial plant that can bloom throughout the year. It is generally expected that pepper inflorescence quantity could be minimized at the nonfull-bloom stage. The objective of this study was to find an appropriate shading measure that could inhibit blooming at other growing stages except the full-bloom stage and did not cause any reduction in pepper yield and quality. In this study, pepper trees were shaded up to 15%, 30%, 60% and 75%, respectively, and the inflorescence quantity, photosynthetic characteristics, pepper yield and quality traits were investigated at every growing stage. The results showed that the effect of shading on pepper yield decreased as time progressed. Shading treatment did not alter the composition of piperine and volatile oil, but reduced the moisture content. Based on the correlation between photosynthetic parameter and inflorescence number, the appropriate shading intensities for regulating inflorescence quantity at different phenological stages were determined. Moreover, it was found that the regulation of inflorescence quantity could be achieved by controlling leaf temperature during recovery to filling period. This research outcome also will give us some guidelines to develop other management strategies that control leaf temperature and regulate inflorescence quantity to consequently improve pepper yield. © 2016 The American Society of Photobiology.

  10. Variation and Change in Northern Bavarian Quantity

    ERIC Educational Resources Information Center

    Drake, Derek

    2013-01-01

    This dissertation presents new research on the "Bavarian Quantity Law" (the BQL) in the northern Bavarian dialect of Hahnbach. Building upon earlier investigation of the BQL (cf. Bannert 1976a,b for Central Bavarian) this study examines the historical, phonological, and phonetic motivations for this feature as well the variability in its…

  11. 10 CFR 26.109 - Urine specimen quantity.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 1 2014-01-01 2014-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine... shall encourage the donor to drink a reasonable amount of liquid (normally, 8 ounces of water every 30...

  12. 10 CFR 26.109 - Urine specimen quantity.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 1 2013-01-01 2013-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine... shall encourage the donor to drink a reasonable amount of liquid (normally, 8 ounces of water every 30...

  13. 10 CFR 26.109 - Urine specimen quantity.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 1 2012-01-01 2012-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine... shall encourage the donor to drink a reasonable amount of liquid (normally, 8 ounces of water every 30...

  14. 6 CFR 27.203 - Calculating the screening threshold quantity by security issue.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 6 Domestic Security 1 2012-01-01 2012-01-01 false Calculating the screening threshold quantity by security issue. 27.203 Section 27.203 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE... the screening threshold quantity by security issue. (a) General. In calculating whether a facility...

  15. Economic order quantity (EOQ) by game theory approach in probabilistic supply chain system under service level constraint for items with imperfect quality

    NASA Astrophysics Data System (ADS)

    Setiawan, R.

    2018-03-01

    In this paper, Economic Order Quantity (EOQ) of probabilistic two-level supply – chain system for items with imperfect quality has been analyzed under service level constraint. A firm applies an active service level constraint to avoid unpredictable shortage terms in the objective function. Mathematical analysis of optimal result is delivered using two equilibrium scheme concept in game theory approach. Stackelberg’s equilibrium for cooperative strategy and Stackelberg’s Equilibrium for noncooperative strategy. This is a new approach to game theory result in inventory system whether service level constraint is applied by a firm in his moves.

  16. Program Evaluation: A Consumer Evaluation of Alternative Contractor Concepts in Government Food Service

    DTIC Science & Technology

    1974-09-01

    food service facilities. The food factors (quality, variety, and quantity, in that order) were generally rated by consumers as most serious problems, in keeping with many previous survey studies of military food service system. The contractor food service concept with raw food provided by the contractor, as exemplified by Fort Myer, significantly reduced consumer problems in food service personnel, speed, hours, environment, and convenience of location, and also reduced the degree to which food variety,

  17. Sleep quantity, quality and optimism in children

    PubMed Central

    Lemola, Sakari; Räikkönen, Katri; Scheier, Michael F.; Matthews, Karen A.; Pesonen, Anu-Katriina; Heinonen, Kati; Lahti, Jari; Komsi, Niina; Paavonen, E. Juulia; Kajantie, Eero

    2014-01-01

    We tested the relationship of objectively-measured sleep quantity and quality with positive characteristics of the child. Sleep duration, sleep latency, and sleep efficiency were measured by an actigraph for an average seven (range = 3 to 14) consecutive nights in 291 eight-year-old children (SD = 0.3 years). Children's optimism, self-esteem, and social competence were rated by parents and/or teachers. Sleep duration showed a non-linear, reverse J-shaped relationship with optimism (P = 0.02) such that children with sleep duration in the middle of the distribution scored higher in optimism compared to children who slept relatively little. Shorter sleep latency was related to higher optimism (P = 0.01). The associations remained when adjusting for child's age, sex, body mass index and parental level of education; the effects of sleep on optimism were neither changed when the parents' own optimism was controlled. In conclusion, sufficient sleep quantity and good sleep quality are associated with positive characteristics of the child, further underlining their importance in promoting well-being in children. PMID:20561178

  18. Methodology to Estimate the Quantity, Composition, and ...

    EPA Pesticide Factsheets

    This report, Methodology to Estimate the Quantity, Composition and Management of Construction and Demolition Debris in the US, was developed to expand access to data on CDD in the US and to support research on CDD and sustainable materials management. Since past US EPA CDD estimates have been limited to building-related CDD, a goal in the development of this methodology was to use data originating from CDD facilities and contractors to better capture the current picture of total CDD management, including materials from roads, bridges and infrastructure. This report, Methodology to Estimate the Quantity, Composition and Management of Construction and Demolition Debris in the US, was developed to expand access to data on CDD in the US and to support research on CDD and sustainable materials management. Since past US EPA CDD estimates have been limited to building-related CDD, a goal in the development of this methodology was to use data originating from CDD facilities and contractors to better capture the current picture of total CDD management, including materials from roads, bridges and infrastructure.

  19. Precise and efficient evaluation of gravimetric quantities at arbitrarily scattered points in space

    NASA Astrophysics Data System (ADS)

    Ivanov, Kamen G.; Pavlis, Nikolaos K.; Petrushev, Pencho

    2017-12-01

    Gravimetric quantities are commonly represented in terms of high degree surface or solid spherical harmonics. After EGM2008, such expansions routinely extend to spherical harmonic degree 2190, which makes the computation of gravimetric quantities at a large number of arbitrarily scattered points in space using harmonic synthesis, a very computationally demanding process. We present here the development of an algorithm and its associated software for the efficient and precise evaluation of gravimetric quantities, represented in high degree solid spherical harmonics, at arbitrarily scattered points in the space exterior to the surface of the Earth. The new algorithm is based on representation of the quantities of interest in solid ellipsoidal harmonics and application of the tensor product trigonometric needlets. A FORTRAN implementation of this algorithm has been developed and extensively tested. The capabilities of the code are demonstrated using as examples the disturbing potential T, height anomaly ζ , gravity anomaly Δ g , gravity disturbance δ g , north-south deflection of the vertical ξ , east-west deflection of the vertical η , and the second radial derivative T_{rr} of the disturbing potential. After a pre-computational step that takes between 1 and 2 h per quantity, the current version of the software is capable of computing on a standard PC each of these quantities in the range from the surface of the Earth up to 544 km above that surface at speeds between 20,000 and 40,000 point evaluations per second, depending on the gravimetric quantity being evaluated, while the relative error does not exceed 10^{-6} and the memory (RAM) use is 9.3 GB.

  20. Electrophysiological evidence for differential processing of numerical quantity and order in humans.

    PubMed

    Turconi, Eva; Jemel, Boutheina; Rossion, Bruno; Seron, Xavier

    2004-09-01

    It is yet unclear whether the processing of number magnitude and order rely on common or different functional processes and neural substrates. On the one hand, recent neuroimaging studies show that quantity and order coding activate the same areas in the parietal and prefrontal cortices. On the other hand, evidence from developmental and neuropsychological studies suggest dissociated mechanisms for processing quantity and order information. To clarify this issue, the present study investigated the spatio-temporal course of quantity and order coding operations using event-related potentials (ERPs). Twenty-four subjects performed a quantity task (classifying numbers as smaller or larger than 15) and an order task on the same material (classifying numbers as coming before or after 15), as well as a control order task on letters (classifying letters as coming before or after M). Behavioral results showed a classical distance effect (decreasing reaction times [RTs] with increasing distance from the standard) for all tasks. In agreement with previous electrophysiological evidence, this effect was significant on a P2 parietal component for numerical material. However, the difference between processing numbers close or far from the target appeared earlier and was larger on the left hemisphere for quantity processing, while it was delayed and bilateral for order processing. There was also a significant distance effect in all tasks on parietal sites for the following P3 component elicited by numbers, but this effect was larger on prefrontal areas for the order judgment. In conclusion, both quantity and order show similar behavioral effects, but they are associated with different spatio-temporal courses in parietal and prefrontal cortices.

  1. Monitoring the eye lens: which dose quantity is adequate?

    NASA Astrophysics Data System (ADS)

    Behrens, R.; Dietze, G.

    2010-07-01

    Recent epidemiological studies suggest a rather low dose threshold (below 0.5 Gy) for the induction of a cataract of the eye lens. Some other studies even assume that there is no threshold at all. Therefore, protection measures have to be optimized and current dose limits for the eye lens may be reduced in the future. The question of which personal dose equivalent quantity is appropriate for monitoring the dose to the eye lens arises from this situation. While in many countries dosemeters calibrated in terms of the dose equivalent quantity Hp(0.07) have been seen as being adequate for monitoring the dose to the eye lens, this might be questionable in the case of reduced dose limits and, thus, it may become necessary to use the dose equivalent quantity Hp(3) for this purpose. To discuss this question, the dose conversion coefficients for the equivalent dose of the eye lens (in the following eye lens dose) were determined for realistic photon and beta radiation fields and compared with the values of the corresponding conversion coefficients for the different operational quantities. The values obtained lead to the following conclusions: in radiation fields where most of the dose comes from photons, especially x-rays, it is appropriate to use dosemeters calibrated in terms of Hp(0.07) on a slab phantom, while in other radiation fields (dominated by beta radiation or unknown contributions of photon and beta radiation) dosemeters calibrated in terms of Hp(3) on a slab phantom should be used. As an alternative, dosemeters calibrated in terms of Hp(0.07) on a slab phantom could also be used; however, in radiation fields containing beta radiation with the end point energy near 1 MeV, an overestimation of the eye lens dose by up to a factor of 550 is possible.

  2. Monitoring the eye lens: which dose quantity is adequate?

    PubMed

    Behrens, R; Dietze, G

    2010-07-21

    Recent epidemiological studies suggest a rather low dose threshold (below 0.5 Gy) for the induction of a cataract of the eye lens. Some other studies even assume that there is no threshold at all. Therefore, protection measures have to be optimized and current dose limits for the eye lens may be reduced in the future. The question of which personal dose equivalent quantity is appropriate for monitoring the dose to the eye lens arises from this situation. While in many countries dosemeters calibrated in terms of the dose equivalent quantity H(p)(0.07) have been seen as being adequate for monitoring the dose to the eye lens, this might be questionable in the case of reduced dose limits and, thus, it may become necessary to use the dose equivalent quantity H(p)(3) for this purpose. To discuss this question, the dose conversion coefficients for the equivalent dose of the eye lens (in the following eye lens dose) were determined for realistic photon and beta radiation fields and compared with the values of the corresponding conversion coefficients for the different operational quantities. The values obtained lead to the following conclusions: in radiation fields where most of the dose comes from photons, especially x-rays, it is appropriate to use dosemeters calibrated in terms of H(p)(0.07) on a slab phantom, while in other radiation fields (dominated by beta radiation or unknown contributions of photon and beta radiation) dosemeters calibrated in terms of H(p)(3) on a slab phantom should be used. As an alternative, dosemeters calibrated in terms of H(p)(0.07) on a slab phantom could also be used; however, in radiation fields containing beta radiation with the end point energy near 1 MeV, an overestimation of the eye lens dose by up to a factor of 550 is possible.

  3. Chemical Waste Management for the Conditionally Exempt Small Quantity Generator

    NASA Astrophysics Data System (ADS)

    Zimmer, Steven W.

    1999-06-01

    Management of hazardous chemical wastes generated as a part of the curriculum poses a significant task for the individual responsible for maintaining compliance with all rules and regulations from the Environmental Protection Agency and the Department of Transportation while maintaining the principles of OSHA's Lab Standard and the Hazard Communication Standard. For schools that generate relatively small quantities of waste, an individual can effectively manage the waste program without becoming overly burdened by the EPA regulations required for those generating large quantities of waste, if given the necessary support from the institution.

  4. Would more social partners leads to enhanced health? The paradox between quantity and quality.

    PubMed

    Xing, Cai; Zhang, Xin; Cheng, Sheung-Tak

    2017-09-01

    In the current investigation, we examined the association between social network composition (SNC) and mental health, as well as whether quantity and quality of social network could influence mental health differently. The social network quantity and quality of 345 middle-aged and older Chinese adults were measured by the Social Convoy Questionnaire. The Chinese version of the Medical Outcome Studies 36-item Short-Form Health Survey (SF-36) was used to assess mental health while controlling for physical health. It was found that both quantity and quality of social network were associated with mental health, and more specifically that (1) quantity of peripheral partners (PP) was positively associated with mental health; (2) quality of emotionally close social partners (ECSP) influenced mental health the most; and (3) paradoxically, the effect of ECSP quality on mental health depended on quantity of ECSP, that is, participants with more ECSP showed a stronger association between ECSP quality and mental health. The findings replicated and extended previous studies on SNC and suggested that structure/quantity and quality of SNC were both important for mental health. © 2017 The Institute of Psychology, Chinese Academy of Sciences and John Wiley & Sons Australia, Ltd.

  5. 48 CFR 47.305-7 - Quantity analysis, direct delivery, and reduction of crosshauling and backhauling.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Quantity analysis, direct... Contracts 47.305-7 Quantity analysis, direct delivery, and reduction of crosshauling and backhauling. (a) Quantity analysis. (1) The requiring activity shall consider the acquisition of carload or truckload...

  6. The diversity of the ecosystem services concept and its implications for their assessment and management.

    PubMed

    Lamarque, Pénélope; Quétier, Fabien; Lavorel, Sandra

    2011-05-01

    The ecosystem services concept is used in different scientific disciplines and is spreading into policy and business circles to draw attention to the benefits that people receive from biodiversity and ecosystems. However, the concept remains multiform and is used interchangeably with a range of other terms such as ecological, landscape or environmental services. We argue that lexical differences, in fact, result from different understandings of the concept, which could slow its use in nature conservation or sustainable resource use. An application to semi-natural grasslands shows that such differences could lead to very different assessments, of quality, quantity and location of ecosystem services. We argue that a compromise must be found between a broad and simple definition, which is useful for communicating the concept and large-scale policies, and a more refined definition for research and implementation goals such as environmental management and national and international assessments and accounting. Copyright © 2010 Académie des sciences. Published by Elsevier SAS. All rights reserved.

  7. 7 CFR 760.810 - Qualifying 2005, 2006, or 2007 quantity crop losses.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... containment or release of the water; or (9) If losses could be attributed to conditions occurring outside of... 7 Agriculture 7 2010-01-01 2010-01-01 false Qualifying 2005, 2006, or 2007 quantity crop losses... Disaster Program § 760.810 Qualifying 2005, 2006, or 2007 quantity crop losses. (a) To receive benefits...

  8. 6 CFR 27.203 - Calculating the screening threshold quantity by security issue.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 6 Domestic Security 1 2014-01-01 2014-01-01 false Calculating the screening threshold quantity by security issue. 27.203 Section 27.203 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Chemical Facility Security Program § 27.203 Calculating the screening threshold quantity by...

  9. 6 CFR 27.203 - Calculating the screening threshold quantity by security issue.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 6 Domestic Security 1 2011-01-01 2011-01-01 false Calculating the screening threshold quantity by security issue. 27.203 Section 27.203 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Chemical Facility Security Program § 27.203 Calculating the screening threshold quantity by...

  10. 6 CFR 27.203 - Calculating the screening threshold quantity by security issue.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 6 Domestic Security 1 2013-01-01 2013-01-01 false Calculating the screening threshold quantity by security issue. 27.203 Section 27.203 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Chemical Facility Security Program § 27.203 Calculating the screening threshold quantity by...

  11. 6 CFR 27.203 - Calculating the screening threshold quantity by security issue.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 6 Domestic Security 1 2010-01-01 2010-01-01 false Calculating the screening threshold quantity by security issue. 27.203 Section 27.203 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Chemical Facility Security Program § 27.203 Calculating the screening threshold quantity by...

  12. Concepts of formal concept analysis

    NASA Astrophysics Data System (ADS)

    Žáček, Martin; Homola, Dan; Miarka, Rostislav

    2017-07-01

    The aim of this article is apply of Formal Concept Analysis on concept of world. Formal concept analysis (FCA) as a methodology of data analysis, information management and knowledge representation has potential to be applied to a verity of linguistic problems. FCA is mathematical theory for concepts and concept hierarchies that reflects an understanding of concept. Formal concept analysis explicitly formalizes extension and intension of a concept, their mutual relationships. A distinguishing feature of FCA is an inherent integration of three components of conceptual processing of data and knowledge, namely, the discovery and reasoning with concepts in data, discovery and reasoning with dependencies in data, and visualization of data, concepts, and dependencies with folding/unfolding capabilities.

  13. Feasibility of a nuclear gauge for fuel quantity measurement aboard aircraft

    NASA Technical Reports Server (NTRS)

    Signh, J. J.; Mall, G. H.; Sprinkle, D. R.; Chegini, H.

    1986-01-01

    Capacitance fuel gauges have served as the basis for fuel quantity indicating systems in aircraft for several decades. However, there have been persistent reports by the airlines that these gauges often give faulty indications due to microbial growth and other contaminants in the fuel tanks. This report describes the results of a feasibility study of using gamma ray attenuation as the basis for measuring fuel quantity in the tanks. Studies with a weak Am-241 59.5-keV radiation source indicate that it is possible to continuously monitor the fuel quantity in the tanks to an accuracy of better than 1 percent. These measurements also indicate that there are easily measurable differences in the physical properties and resultant attenuation characteristics of JP-4, JP-5, and Jet A fuels. The experimental results, along with a suggested source-detector geometrical configuration are described.

  14. [Green space vegetation quantity in workshop area of Wuhan Iron and Steel Company].

    PubMed

    Chen, Fang; Zhou, Zhixiang; Wang, Pengcheng; Li, Haifang; Zhong, Yingfei

    2006-04-01

    Aimed at the complex community structure and higher fragmentation of urban green space, and based on the investigation of synusia structure and its coverage, this paper studied the vegetation quantity of ornamental green space in the workshop area of Wuhan Iron and Steel Company, with the help of GIS. The results showed that different life forms of ornamental plants in this area had a greater difference in their single leaf area and leaf area index (LAI), and the LAI was not only depended on single leaf area, but also governed by the shape of tree crown and the intensive degree of branches and leaves. The total vegetation quantity was 1 694.2 hm2, with the average LAI being 7.75, and the vegetation quantity of arbor-shrub-herb and arbor-shrub communities accounted for 79.7% and 92.3% of the total, respectively, reflecting that the green space structure was dominated by arbor species and by arbor-shrub-herb and arbor-shrub community types. Single layer-structured lawn had a less percentage, while the vegetation quantity of herb synusia accounted for 22.9% of the total, suggesting an afforestation characteristic of "making use of every bit of space" in the workshop area. The vegetation quantity of urban ornamental green space depended on the area of green space, its synusia structure, and the LAI and coverage of ornamental plants. In enlarging urban green space, ornamental plant species with high LAI should be selected, and community structure should be improved to have a higher vegetation quantity in urban area. To quantify the vegetation quantity of urban ornamental green space more accurately, synusia should be taken as the unit to measure the LAI of typical species, and the synusia structure and its coverage of different community types should be investigated with the help of remote sensing images and GIS.

  15. 7 CFR 983.53 - Testing of minimal quantities.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA... her entire inventory of hulled and dried pistachios for the aflatoxin certification before further... regarding the testing of minimal quantities of pistachios for quality. [74 FR 56540, Nov. 2, 2009] ...

  16. 21 CFR 501.105 - Declaration of net quantity of contents when exempt.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... principal display panel. (p) A separate statement of the net quantity of contents in terms of the metric system is not regarded as a supplemental statement and an accurate statement of the net quantity of contents in terms of the metric system of weight or measure may also appear on the principal display panel...

  17. 21 CFR 501.105 - Declaration of net quantity of contents when exempt.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... principal display panel. (p) A separate statement of the net quantity of contents in terms of the metric system is not regarded as a supplemental statement and an accurate statement of the net quantity of contents in terms of the metric system of weight or measure may also appear on the principal display panel...

  18. 21 CFR 501.105 - Declaration of net quantity of contents when exempt.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... principal display panel. (p) A separate statement of the net quantity of contents in terms of the metric system is not regarded as a supplemental statement and an accurate statement of the net quantity of contents in terms of the metric system of weight or measure may also appear on the principal display panel...

  19. 21 CFR 501.105 - Declaration of net quantity of contents when exempt.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... principal display panel. (p) A separate statement of the net quantity of contents in terms of the metric system is not regarded as a supplemental statement and an accurate statement of the net quantity of contents in terms of the metric system of weight or measure may also appear on the principal display panel...

  20. Atomic Layer Deposition on Gram Quantities of Multi-Walled Carbon Nanotubes

    DTIC Science & Technology

    2009-06-03

    the amount of reactant that is lost to the vacuum pump . Recent work has demonstrated the feasibility of ALD on gram quantities of nanopowders in a...and left to outgas under vacuum for 24 h. Vacuum was obtained using a dual-stage rotary vane pump . Pressure was monitored with a Baratron capacitance...Atomic layer deposition on gram quantities of multi-walled carbon nanotubes This article has been downloaded from IOPscience. Please scroll down to

  1. Genistein Enhances or Reduces Glycosaminoglycan Quantity in a Cell Type-Specific Manner.

    PubMed

    Lan, Ying; Li, Xiulian; Liu, Xuebo; Hao, Cui; Song, Ni; Ren, Sumei; Wang, Wei; Feng, Ningchuan; Zhang, Lijuan

    2018-06-27

    Genistein is a natural isoflavone enriched in soybeans. It has beneficial effects for patients with mucopolysaccharidose type III through inhibiting glycosaminoglycan biosynthesis. However, other studies indicate that genistein does not always inhibit glycosaminoglycan biosynthesis. To understand the underlying molecular mechanisms, CHOK1, CHO3.1, CHO3.3, and HCT116 cells were treated with genistein and the monosaccharide compositions and quantity of all glycans from the cell lysate were measured after thorough acid hydrolysis followed by HPLC analysis. In addition, the glycosaminoglycan disaccharide compositions were obtained by stable isotope labeling coupled with LC/MS analysis. Genistein treatment reduced the amount of glycans but increased the amount of glycosaminoglycans in HCT116 cells. In contrast, genistein treatment reduced both glycan and glycosaminoglycan quantities in CHOK1, CHO3.1, and CHO3.3 cells in addition to differential changes in glycosaminoglycan disaccharide compositions. Genistein treatment reduced overall glycan quantity but glycosaminoglycan quantities were either increased or decreased in a cell type-dependent manner. © 2018 The Author(s). Published by S. Karger AG, Basel.

  2. Symbolic Estrangement: Evidence against a Strong Association between Numerical Symbols and the Quantities They Represent

    ERIC Educational Resources Information Center

    Lyons, Ian M.; Ansari, Daniel; Beilock, Sian L.

    2012-01-01

    Are numerals estranged from a sense of the actual quantities they represent? We demonstrate that, irrespective of numerical size or distance, direct comparison of the relative quantities represented by symbolic and nonsymbolic formats leads to performance markedly worse than when comparing 2 nonsymbolic quantities (Experiment 1). Experiment 2…

  3. Physics holo.lab learning experience: using smartglasses for augmented reality labwork to foster the concepts of heat conduction

    NASA Astrophysics Data System (ADS)

    Strzys, M. P.; Kapp, S.; Thees, M.; Klein, P.; Lukowicz, P.; Knierim, P.; Schmidt, A.; Kuhn, J.

    2018-05-01

    Fundamental concepts of thermodynamics rely on abstract physical quantities such as energy, heat and entropy, which play an important role in the process of interpreting thermal phenomena and statistical mechanics. However, these quantities are not covered by human visual perception, and since heat sensation is purely qualitative and easy to deceive, an intuitive understanding often is lacking. Today immersive technologies like head-mounted displays of the newest generation, especially HoloLens, allow for high-quality augmented reality learning experiences, which can overcome this gap in human perception by presenting different representations of otherwise invisible quantities directly in the field of view of the user on the experimental apparatus, which simultaneously avoids a split-attention effect. In a mixed reality (MR) scenario as presented in this paper—which we call a holo.lab—human perception can be extended to the thermal regime by presenting false-color representations of the temperature of objects as a virtual augmentation directly on the real object itself in real-time. Direct feedback to experimental actions of the users in the form of different representations allows for immediate comparison to theoretical principles and predictions and therefore is supposed to intensify the theory–experiment interactions and to increase students’ conceptual understanding. We tested this technology for an experiment on thermal conduction of metals in the framework of undergraduate laboratories. A pilot study with treatment and control groups (N = 59) showed a small positive effect of MR on students’ performance measured with a standardized concept test for thermodynamics, pointing to an improvement of the understanding of the underlying physical concepts. These findings indicate that complex experiments could benefit even more from augmentation. This motivates us to enrich further experiments with MR.

  4. Assess water scarcity integrating water quantity and quality

    NASA Astrophysics Data System (ADS)

    Liu, J.; Zeng, Z.

    2014-12-01

    Water scarcity has become widespread all over the world. Current methods for water scarcity assessment are mainly based on water quantity and seldom consider water quality. Here, we develop an approach for assessing water scarcity considering both water quantity and quality. In this approach, a new water scarcity index is used to describe the severity of water scarcity in the form of a water scarcity meter, which may help to communicate water scarcity to a wider audience. To illustrate the approach, we analyzed the historical trend of water scarcity for Beijing city in China during 1995-2009, as well as the assessment for different river basins in China. The results show that Beijing made a huge progress in mitigating water scarcity, and that from 1999 to 2009 the blue and grey water scarcity index decreased by 59% and 62%, respectively. Despite this progress, we demonstrate that Beijing is still characterized by serious water scarcity due to both water quantity and quality. The water scarcity index remained at a high value of 3.5 with a blue and grey water scarcity index of 1.2 and 2.3 in 2009 (exceeding the thresholds of 0.4 and 1, respectively). As a result of unsustainable water use and pollution, groundwater levels continue to decline, and water quality shows a continuously deteriorating trend. To curb this trend, future water policies should further decrease water withdrawal from local sources (in particular groundwater) within Beijing, and should limit the grey water footprint below the total amount of water resources.

  5. Do Social Conditions Affect Capuchin Monkeys' (Cebus apella) Choices in a Quantity Judgment Task?

    PubMed

    Beran, Michael J; Perdue, Bonnie M; Parrish, Audrey E; Evans, Theodore A

    2012-01-01

    Beran et al. (2012) reported that capuchin monkeys closely matched the performance of humans in a quantity judgment test in which information was incomplete but a judgment still had to be made. In each test session, subjects first made quantity judgments between two known options. Then, they made choices where only one option was visible. Both humans and capuchin monkeys were guided by past outcomes, as they shifted from selecting a known option to selecting an unknown option at the point at which the known option went from being more than the average rate of return to less than the average rate of return from earlier choices in the test session. Here, we expanded this assessment of what guides quantity judgment choice behavior in the face of incomplete information to include manipulations to the unselected quantity. We manipulated the unchosen set in two ways: first, we showed the monkeys what they did not get (the unchosen set), anticipating that "losses" would weigh heavily on subsequent trials in which the same known quantity was presented. Second, we sometimes gave the unchosen set to another monkey, anticipating that this social manipulation might influence the risk-taking responses of the focal monkey when faced with incomplete information. However, neither manipulation caused difficulty for the monkeys who instead continued to use the rational strategy of choosing known sets when they were as large as or larger than the average rate of return in the session, and choosing the unknown (riskier) set when the known set was not sufficiently large. As in past experiments, this was true across a variety of daily ranges of quantities, indicating that monkeys were not using some absolute quantity as a threshold for selecting (or not) the known set, but instead continued to use the daily average rate of return to determine when to choose the known versus the unknown quantity.

  6. 76 FR 82320 - Ethyl Alcohol for Fuel Use: Determination of the Base Quantity of Imports

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-30

    ...: Determination of the Base Quantity of Imports AGENCY: United States International Trade Commission. [[Page 82321... to establish the ``base quantity'' of imports of fuel ethyl alcohol with a zero percent local... base quantity to be used by U.S. Customs and Border Protection in the administration of the law is the...

  7. Monitoring on The Quality and Quantity of DIY Rainwater Harvesting System

    NASA Astrophysics Data System (ADS)

    Kasmin, H.; Bakar, N. H.; Zubir, M. M.

    2016-07-01

    Rainwater harvesting is an alternative sources of water supply and can be used for potable and non-potable uses. It could helps to store treated rainwater for more beneficial use and also for flood mitigation. Sustainable approach for flooding problem reduction in urban areas is by slowing down the rate of surface runoff flows at source by providing more storage area/tank. In order to understand the performance of a rainwater harvesting system (RWH), a preliminary monitoring on a ‘do it yourself’ (DIY) RWH model with additional first -flush strategy for water quality treatment was done. The main concept behind first flush diversion is to prevent initial polluted rainwater from entering the storage tank. Based on seven rainfall events observed in Parit Raja, both quality and quantity of the rainfalls were analysed. For rainwater quality, the samples from first flush diverter and storage tank were taken to understand their performance based on pH, dissolved oxygen (DO), turbidity, total dissolved solid (TDS), total suspended solid (TSS), chemical oxygen demand (COD) and biochemical oxygen demand (BOD) parameters. While for rainwater quantity, hydrograph analysis were done based on the performance of total rainfall and runoff, peak flow of rainfall and runoff; and delayed time parameters. Based on Interim National Water Quality Standard (INWQS) and National Drinking Water Quality Standard (NDWQS), first flush diverter apparently helps on water quality improvement in storage tanks when pH, DO, TDS, TSS and turbidity were classified as Class I (INWQS) and is allowable for drinking; but BOD and COD parameters were classified as Class III (INWQS). Hence, it has potential to be used as potable usage but will need extensive treatment to reduce its poor microbial quality. Based on the maximum observed rainfall event which had total volume of 3195.5 liter, had peakflow reduction from 0.00071 m3/s to 0.00034 m3/s and delayed runoff between 5 and 10 minutes after rainfall

  8. Calculating Time-Integral Quantities in Depletion Calculations

    DOE PAGES

    Isotalo, Aarno

    2016-06-02

    A method referred to as tally nuclides is presented for accurately and efficiently calculating the time-step averages and integrals of any quantities that are weighted sums of atomic densities with constant weights during the step. The method allows all such quantities to be calculated simultaneously as a part of a single depletion solution with existing depletion algorithms. Some examples of the results that can be extracted include step-average atomic densities and macroscopic reaction rates, the total number of fissions during the step, and the amount of energy released during the step. Furthermore, the method should be applicable with several depletionmore » algorithms, and the integrals or averages should be calculated with an accuracy comparable to that reached by the selected algorithm for end-of-step atomic densities. The accuracy of the method is demonstrated in depletion calculations using the Chebyshev rational approximation method. Here, we demonstrate how the ability to calculate energy release in depletion calculations can be used to determine the accuracy of the normalization in a constant-power burnup calculation during the calculation without a need for a reference solution.« less

  9. 27 CFR 25.183 - Determination of quantity transferred.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... transferred. 25.183 Section 25.183 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY ALCOHOL BEER Removals Without Payment of Tax Transfer to Another Brewery of Same Ownership § 25.183 Determination of quantity transferred. The shipping brewer shall...

  10. Concepts for the design of a completely active helicopter isolation system using output vector feedback

    NASA Technical Reports Server (NTRS)

    Schulz, G.

    1977-01-01

    The theory of output vector feedback (a few measured quantities) is used to derive completely active oscillation isolation functions for helicopters. These feedback controller concepts are tested with various versions of the BO 105 helicopter and their performance is demonstrated. A compensation of the vibrational excitations from the rotor and harmonics of the number of blades are considered. There is also a fast and automatic trim function for maneuvers.

  11. Enzyme catalysis with small ionic liquid quantities.

    PubMed

    Fischer, Fabian; Mutschler, Julien; Zufferey, Daniel

    2011-04-01

    Enzyme catalysis with minimal ionic liquid quantities improves reaction rates, stereoselectivity and enables solvent-free processing. In particular the widely used lipases combine well with many ionic liquids. Demonstrated applications are racemate separation, esterification and glycerolysis. Minimal solvent processing is also an alternative to sluggish solvent-free catalysis. The method allows simplified down-stream processing, as only traces of ionic liquids have to be removed.

  12. Coordination of Fractional Quantities: Cueing of Resources, Constraints, and Effect of Numeric Structure

    ERIC Educational Resources Information Center

    Ramful, Ajay; Nenduradu, Rajeev

    2013-01-01

    While previous work in the domain of proportional reasoning has primarily focused on the coordination of integer quantities, this study investigates how students coordinate fractional quantities. Fine-grained analysis of two seventh graders' responses to a set of systematically designed proportional tasks, shows how their knowledge of…

  13. 10 CFR 76.113 - Formula quantities of strategic special nuclear material-Category I.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Formula quantities of strategic special nuclear material-Category I. 76.113 Section 76.113 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safeguards and Security § 76.113 Formula quantities of strategic special nuclear material...

  14. 10 CFR 76.113 - Formula quantities of strategic special nuclear material-Category I.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Formula quantities of strategic special nuclear material-Category I. 76.113 Section 76.113 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safeguards and Security § 76.113 Formula quantities of strategic special nuclear material...

  15. 10 CFR 76.113 - Formula quantities of strategic special nuclear material-Category I.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Formula quantities of strategic special nuclear material-Category I. 76.113 Section 76.113 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safeguards and Security § 76.113 Formula quantities of strategic special nuclear material...

  16. 10 CFR 76.113 - Formula quantities of strategic special nuclear material-Category I.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Formula quantities of strategic special nuclear material-Category I. 76.113 Section 76.113 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safeguards and Security § 76.113 Formula quantities of strategic special nuclear material...

  17. 10 CFR 76.113 - Formula quantities of strategic special nuclear material-Category I.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Formula quantities of strategic special nuclear material-Category I. 76.113 Section 76.113 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safeguards and Security § 76.113 Formula quantities of strategic special nuclear material...

  18. 43 CFR 3430.1-2 - Commercial quantities defined.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Section 3430.1-2 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND... quantities is defined as follows: (a) The coal deposit discovered under the prospecting permit shall be of... sale of the coal shall exceed the cost of developing the mine and extracting, removing, transporting...

  19. 43 CFR 3430.1-2 - Commercial quantities defined.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Section 3430.1-2 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND... quantities is defined as follows: (a) The coal deposit discovered under the prospecting permit shall be of... sale of the coal shall exceed the cost of developing the mine and extracting, removing, transporting...

  20. CONCEPT LEARNING AND CONCEPT TEACHING.

    ERIC Educational Resources Information Center

    GLASER, ROBERT

    REVIEWED ARE THE PSYCHOLOGICAL STUDIES OF CONCEPT LEARNING AS THEY RELATE TO CONCEPT TEACHING. AN ANALYSIS IS MADE OF THE NATURE OF CONCEPT LEARNING AS IT IS STUDIED IN THE PSYCHOLOGIST'S LABORATORY, INCLUDING THE NATURE OF CONCEPT TASKS AS THEY APPEAR IN SUBJECT MATTER LEARNING. THE PRIMARY KINDS OF CONCEPT LEARNING SITUATIONS, INCLUDING THE…

  1. 46 CFR 108.439 - Quantity of CO2 for protection of spaces.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Quantity of CO2 for protection of spaces. 108.439... Systems § 108.439 Quantity of CO2 for protection of spaces. (a) The number of pounds of CO2 required to... calculated using the reductions allowed in 46 CFR 95.10-5(e). (c) If fuel can drain from a space to an...

  2. 46 CFR 108.439 - Quantity of CO2 for protection of spaces.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Quantity of CO2 for protection of spaces. 108.439... Systems § 108.439 Quantity of CO2 for protection of spaces. (a) The number of pounds of CO2 required to... calculated using the reductions allowed in 46 CFR 95.10-5(e). (c) If fuel can drain from a space to an...

  3. 46 CFR 108.439 - Quantity of CO2 for protection of spaces.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Quantity of CO2 for protection of spaces. 108.439... Systems § 108.439 Quantity of CO2 for protection of spaces. (a) The number of pounds of CO2 required to... calculated using the reductions allowed in 46 CFR 95.10-5(e). (c) If fuel can drain from a space to an...

  4. 46 CFR 108.439 - Quantity of CO2 for protection of spaces.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Quantity of CO2 for protection of spaces. 108.439... Systems § 108.439 Quantity of CO2 for protection of spaces. (a) The number of pounds of CO2 required to... calculated using the reductions allowed in 46 CFR 95.10-5(e). (c) If fuel can drain from a space to an...

  5. 46 CFR 108.439 - Quantity of CO2 for protection of spaces.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Quantity of CO2 for protection of spaces. 108.439... Systems § 108.439 Quantity of CO2 for protection of spaces. (a) The number of pounds of CO2 required to... calculated using the reductions allowed in 46 CFR 95.10-5(e). (c) If fuel can drain from a space to an...

  6. Impact of litter quantity on the soil bacteria community during the decomposition of Quercus wutaishanica litter.

    PubMed

    Zeng, Quanchao; Liu, Yang; An, Shaoshan

    2017-01-01

    The forest ecosystem is the main component of terrestrial ecosystems. The global climate and the functions and processes of soil microbes in the ecosystem are all influenced by litter decomposition. The effects of litter decomposition on the abundance of soil microorganisms remain unknown. Here, we analyzed soil bacterial communities during the litter decomposition process in an incubation experiment under treatment with different litter quantities based on annual litterfall data (normal quantity, 200 g/(m 2 /yr); double quantity, 400 g/(m 2 /yr) and control, no litter). The results showed that litter quantity had significant effects on soil carbon fractions, nitrogen fractions, and bacterial community compositions, but significant differences were not found in the soil bacterial diversity. The normal litter quantity enhanced the relative abundance of Actinobacteria and Firmicutes and reduced the relative abundance of Bacteroidetes, Plantctomycets and Nitrospiare. The Beta-, Gamma-, and Deltaproteobacteria were significantly less abundant in the normal quantity litter addition treatment, and were subsequently more abundant in the double quantity litter addition treatment. The bacterial communities transitioned from Proteobacteria-dominant (Beta-, Gamma-, and Delta) to Actinobacteria-dominant during the decomposition of the normal quantity of litter. A cluster analysis showed that the double litter treatment and the control had similar bacterial community compositions. These results suggested that the double quantity litter limited the shift of the soil bacterial community. Our results indicate that litter decomposition alters bacterial dynamics under the accumulation of litter during the vegetation restoration process, which provides important significant guidelines for the management of forest ecosystems.

  7. Using the Bivariate Dale Model to jointly estimate predictors of frequency and quantity of alcohol use.

    PubMed

    McMillan, Garnett P; Hanson, Tim; Bedrick, Edward J; Lapham, Sandra C

    2005-09-01

    This study demonstrates the usefulness of the Bivariate Dale Model (BDM) as a method for estimating the relationship between risk factors and the quantity and frequency of alcohol use, as well as the degree of association between these highly correlated drinking measures. The BDM is used to evaluate childhood sexual abuse, along with age and gender, as risk factors for the quantity and frequency of beer consumption in a sample of driving-while-intoxicated (DWI) offenders (N = 1,964; 1,612 men). The BDM allows one to estimate the relative odds of drinking up to each level of ordinal-scaled quantity and frequency of alcohol use, as well as model the degree of association between quantity and frequency of alcohol consumption as a function of covariates. Individuals who experienced childhood sexual abuse have increased risks of higher quantity and frequency of beer consumption. History of childhood sexual abuse has a greater effect on women, causing them to drink higher quantities of beer per drinking occasion. The BDM is a useful method for evaluating predictors of the quantity-frequency of alcohol consumption. SAS macrocode for fitting the BDM model is provided.

  8. Free-ranging dogs assess the quantity of opponents in intergroup conflicts.

    PubMed

    Bonanni, Roberto; Natoli, Eugenia; Cafazzo, Simona; Valsecchi, Paola

    2011-01-01

    In conflicts between social groups, the decision of competitors whether to attack/retreat should be based on the assessment of the quantity of individuals in their own and the opposing group. Experimental studies on numerical cognition in animals suggest that they may represent both large and small numbers as noisy mental magnitudes subject to scalar variability, and small numbers (≤4) also as discrete object-files. Consequently, discriminating between large quantities, but not between smaller ones, should become easier as the asymmetry between quantities increases. Here, we tested these hypotheses by recording naturally occurring conflicts in a population of free-ranging dogs, Canis lupus familiaris, living in a suburban environment. The overall probability of at least one pack member approaching opponents aggressively increased with a decreasing ratio of the number of rivals to that of companions. Moreover, the probability that more than half of the pack members withdrew from a conflict increased when this ratio increased. The skill of dogs in correctly assessing relative group size appeared to improve with increasing the asymmetry in size when at least one pack comprised more than four individuals, and appeared affected to a lesser extent by group size asymmetries when dogs had to compare only small numbers. These results provide the first indications that a representation of quantity based on noisy mental magnitudes may be involved in the assessment of opponents in intergroup conflicts and leave open the possibility that an additional, more precise mechanism may operate with small numbers.

  9. 40 CFR Appendix A to Part 355 - The List of Extremely Hazardous Substances and Their Threshold Planning Quantities

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Substances and Their Threshold Planning Quantities A Appendix A to Part 355 Protection of Environment... Substances and Their Threshold Planning Quantities [Alphabetical Order] CAS No. Chemical name Notes Reportable quantity *(pounds) Threshold planning quantity(pounds) 75-86-5 Acetone Cyanohydrin 10 1,000 1752...

  10. The orientation distribution of tunneling-related quantities

    NASA Astrophysics Data System (ADS)

    Seif, W. M.; Refaie, A. I.; Botros, M. M.

    2018-03-01

    In the nuclear tunneling processes involving deformed nuclei, most of the tunneling-related quantities depend on the relative orientations of the participating nuclei. In the presence of different multipole deformations, we study the variation of a few relevant quantities for the α-decay and the sub-barrier fusion processes, in an orientation degree of freedom. The knocking frequency and the penetration probability are evaluated within the Wentzel-Kramers-Brillouin approximation. The interaction potential is calculated with Skyrme-type nucleon-nucleon interaction. We found that the width of the potential pocket, the Coulomb barrier radius, the penetration probability, the α-decay width, and the fusion cross-section follow consistently the orientation-angle variation of the radius of the deformed nucleus. The orientation distribution patterns of the pocket width, the barrier radius, the logarithms of the penetrability, the decay width, and the fusion cross-section are found to be highly analogous to pattern of the deformed-nucleus radius. The curve patterns of the orientation angle distributions of the internal pocket depth, the Coulomb barrier height and width, as well as the knocking frequency simulate inversely the variation of the deformed nucleus radius. The predicted orientation behaviors will be of a special interest in predicting the optimum orientations for the tunneling processes.

  11. 40 CFR Appendix B to Part 355 - The List of Extremely Hazardous Substances and Their Threshold Planning Quantities

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Substances and Their Threshold Planning Quantities B Appendix B to Part 355 Protection of Environment... Substances and Their Threshold Planning Quantities [CAS Number Order] CAS No. Chemical name Notes Reportable quantity *(pounds) Threshold planning quantity(pounds) 0 Organorhodium Complex (PMN-82-147) 10 10/10,000 50...

  12. Generalized correlation integral vectors: A distance concept for chaotic dynamical systems

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Haario, Heikki, E-mail: heikki.haario@lut.fi; Kalachev, Leonid, E-mail: KalachevL@mso.umt.edu; Hakkarainen, Janne

    2015-06-15

    Several concepts of fractal dimension have been developed to characterise properties of attractors of chaotic dynamical systems. Numerical approximations of them must be calculated by finite samples of simulated trajectories. In principle, the quantities should not depend on the choice of the trajectory, as long as it provides properly distributed samples of the underlying attractor. In practice, however, the trajectories are sensitive with respect to varying initial values, small changes of the model parameters, to the choice of a solver, numeric tolerances, etc. The purpose of this paper is to present a statistically sound approach to quantify this variability. Wemore » modify the concept of correlation integral to produce a vector that summarises the variability at all selected scales. The distribution of this stochastic vector can be estimated, and it provides a statistical distance concept between trajectories. Here, we demonstrate the use of the distance for the purpose of estimating model parameters of a chaotic dynamic model. The methodology is illustrated using computational examples for the Lorenz 63 and Lorenz 95 systems, together with a framework for Markov chain Monte Carlo sampling to produce posterior distributions of model parameters.« less

  13. Early Numeracy Intervention: Does Quantity Discrimination Really Work?

    ERIC Educational Resources Information Center

    Hansmann, Paul

    2013-01-01

    Scope and Method of Study: The current study demonstrates that a taped problem intervention is an effective tool for increasing the early numeracy skill of QD. A taped problems intervention was used with two variations of the quantity discrimination measure (triangle and traditional). A 3x2 doubly multivariate multivariate analysis of variance was…

  14. Determining the maximum charging currents of lithium-ion cells for small charge quantities

    NASA Astrophysics Data System (ADS)

    Grimsmann, F.; Gerbert, T.; Brauchle, F.; Gruhle, A.; Parisi, J.; Knipper, M.

    2017-10-01

    In order to optimize the operating parameters of battery management systems for electric and hybrid vehicles, great interest has been shown in achieving the maximum permissible charging currents during recuperation, without causing a cell damage due to lithium plating, in relation to the temperature, charge quantity and state of charge. One method for determining these recuperation currents is measuring the cell thickness, where excessively high charging currents can be detected by an irreversible increase in thickness. It is not possible to measure particularly small charge quantities by employing mechanic dial indicators, which have a limited resolution of 1 μm. This is why we developed a measuring setup that has a resolution limit of less than 10 nm using a high-resolution contactless inductance sensor. Our results show that the permissible charging current I can be approximated in relation to the charge quantity x by a correlating function I =a /√{(x) } which is compliant with the Arrhenius law. Small charge quantities therefore have an optimization potential for energy recovery during recuperation.

  15. Development of blueberry liquor: influence of distillate, sweetener and fruit quantity.

    PubMed

    Caldeira, Ilda; Lopes, Daniel; Delgado, Teresa; Canas, Sara; Anjos, Ofélia

    2018-02-01

    In this work different formulations of blueberry liquor were tested and characterised based on their physico-chemical and sensory characteristics. Three factors were evaluated: the distillate used to produce the liquor (wine spirit or grape marc spirit); the sweetener (white sugar or honey) and the fruit quantity (two doses). For each liquor, pH, total acidity, dry soluble solids content, dry extract, alcoholic strength, reducing sugars, colour intensity, methanol content, acetaldehyde and fusel alcohols were determined. Sensory tests were carried out with a trained panel. The three factors studied significantly influenced the physico-chemical features of the liquors, being the quantity of fruit the most discriminating factor, except for the volatile compounds which were mainly influenced by the distillate. As regards the sensory analysis, it was found that the most appreciated liquor was that prepared with wine spirit, sugar and a lower dose of blueberry, and the less appreciated formulation was the one made with grape marc spirit, honey and a lower quantity of blueberry. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  16. Quantity Recognition among Speakers of an Anumeric Language

    ERIC Educational Resources Information Center

    Everett, Caleb; Madora, Keren

    2012-01-01

    Recent research has suggested that the Piraha, an Amazonian tribe with a number-less language, are able to match quantities greater than 3 if the matching task does not require recall or spatial transposition. This finding contravenes previous work among the Piraha. In this study, we re-tested the Pirahas' performance in the crucial one-to-one…

  17. Evaluating the uncertainty of input quantities in measurement models

    NASA Astrophysics Data System (ADS)

    Possolo, Antonio; Elster, Clemens

    2014-06-01

    The Guide to the Expression of Uncertainty in Measurement (GUM) gives guidance about how values and uncertainties should be assigned to the input quantities that appear in measurement models. This contribution offers a concrete proposal for how that guidance may be updated in light of the advances in the evaluation and expression of measurement uncertainty that were made in the course of the twenty years that have elapsed since the publication of the GUM, and also considering situations that the GUM does not yet contemplate. Our motivation is the ongoing conversation about a new edition of the GUM. While generally we favour a Bayesian approach to uncertainty evaluation, we also recognize the value that other approaches may bring to the problems considered here, and focus on methods for uncertainty evaluation and propagation that are widely applicable, including to cases that the GUM has not yet addressed. In addition to Bayesian methods, we discuss maximum-likelihood estimation, robust statistical methods, and measurement models where values of nominal properties play the same role that input quantities play in traditional models. We illustrate these general-purpose techniques in concrete examples, employing data sets that are realistic but that also are of conveniently small sizes. The supplementary material available online lists the R computer code that we have used to produce these examples (stacks.iop.org/Met/51/3/339/mmedia). Although we strive to stay close to clause 4 of the GUM, which addresses the evaluation of uncertainty for input quantities, we depart from it as we review the classes of measurement models that we believe are generally useful in contemporary measurement science. We also considerably expand and update the treatment that the GUM gives to Type B evaluations of uncertainty: reviewing the state-of-the-art, disciplined approach to the elicitation of expert knowledge, and its encapsulation in probability distributions that are usable in

  18. Burden shifting of water quantity and quality stress from megacity Shanghai

    NASA Astrophysics Data System (ADS)

    Zhao, Xu; Liu, Junguo; Yang, Hong; Duarte, Rosa; Tillotson, Martin R.; Hubacek, Klaus

    2016-09-01

    Much attention has been paid to burden shifting of CO2 emissions from developed regions to developing regions through trade. However, less discussed is that trade also acts as a mechanism enabling wealthy consumers to shift water quantity and quality stress to their trading partners. In this study, we investigate how Shanghai, the largest megacity in China, draws water resources from all over China and outsources its pollution through virtual quantity and quality water flows associated with trade. The results show that Shanghai's consumption of goods and services in 2007 led to 11.6 billion m3 of freshwater consumption, 796 thousand tons of COD, and 16.2 thousand tons of NH3-N in discharged wastewater. Of this, 79% of freshwater consumption, 82.9% of COD and 82.5% of NH3-N occurred in other Chinese Provinces which provide goods and services to Shanghai. Thirteen Provinces with severe and extreme water quantity stress accounted for 60% of net virtual water import to Shanghai, while 19 Provinces experiencing water quality stress endured 79% of net COD outsourcing and 75.5% of net NH3-N outsourcing from Shanghai. In accordance with the three "redlines" recently put forward by the Chinese central government to control water pollution and cap total water use in all provinces, we suggest that Shanghai should share its responsibility for reducing water quantity and quality stress in its trading partners through taking measures at provincial, industrial, and consumer levels. In the meantime, Shanghai needs to enhance demand side management by promoting low water intensity consumption.

  19. Facilitating students' application of the integral and the area under the curve concepts in physics problems

    NASA Astrophysics Data System (ADS)

    Nguyen, Dong-Hai

    This research project investigates the difficulties students encounter when solving physics problems involving the integral and the area under the curve concepts and the strategies to facilitate students learning to solve those types of problems. The research contexts of this project are calculus-based physics courses covering mechanics and electromagnetism. In phase I of the project, individual teaching/learning interviews were conducted with 20 students in mechanics and 15 students from the same cohort in electromagnetism. The students were asked to solve problems on several topics of mechanics and electromagnetism. These problems involved calculating physical quantities (e.g. velocity, acceleration, work, electric field, electric resistance, electric current) by integrating or finding the area under the curve of functions of related quantities (e.g. position, velocity, force, charge density, resistivity, current density). Verbal hints were provided when students made an error or were unable to proceed. A total number of 140 one-hour interviews were conducted in this phase, which provided insights into students' difficulties when solving the problems involving the integral and the area under the curve concepts and the hints to help students overcome those difficulties. In phase II of the project, tutorials were created to facilitate students' learning to solve physics problems involving the integral and the area under the curve concepts. Each tutorial consisted of a set of exercises and a protocol that incorporated the helpful hints to target the difficulties that students expressed in phase I of the project. Focus group learning interviews were conducted to test the effectiveness of the tutorials in comparison with standard learning materials (i.e. textbook problems and solutions). Overall results indicated that students learning with our tutorials outperformed students learning with standard materials in applying the integral and the area under the curve

  20. Mass quantity gauging by RF mode analysis

    NASA Technical Reports Server (NTRS)

    Collier, R. S.; Ellerbruch, D.; Cruz, J. E.; Stokes, R. W.; Luft, P. E.; Peterson, R. G.; Hiester, A. E.

    1973-01-01

    Work done to date is reported concerning Radio Frequency Mass Quantity Gauging. Experimental apparatus has been designed and tested which measures the resonant frequencies of a tank in the time domain. These frequencies correspond to the total mass of fluid within the tank. Experimental results are discussed for nitrogen and hydrogen in normal gravity both in the supercritical state and also in the two phase (liquid-gas) region. Theoretical discussions for more general cases are given.

  1. Does quantity generate quality? Testing the fundamental principle of brainstorming.

    PubMed

    Muñoz Adánez, Alfredo

    2005-11-01

    The purpose of this work is to test the chief principle of brainstorming, formulated as "quantity generates quality." The study is included within a broad program whose goal is to detect the strong and weak points of creative techniques. In a sample of 69 groups, containing between 3 and 8 members, the concurrence of two commonly accepted criteria was established as a quality rule: originality and utility or value. The results fully support the quantity-quality relation (r = .893): the more ideas produced to solve a problem, the better quality of the ideas. The importance of this finding, which supports Osborn's theory, is discussed, and the use of brainstorming is recommended to solve the many open problems faced by our society.

  2. 40 CFR 355.12 - What quantities of extremely hazardous substances trigger emergency planning requirements?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... EMERGENCY PLANNING AND NOTIFICATION Emergency Planning Who Must Comply § 355.12 What quantities of extremely... 40 Protection of Environment 27 2010-07-01 2010-07-01 false What quantities of extremely hazardous substances trigger emergency planning requirements? 355.12 Section 355.12 Protection of Environment...

  3. Relative quantity judgments in the beluga whale (Delphinapterus leucas) and the bottlenose dolphin (Tursiops truncatus).

    PubMed

    Abramson, José Z; Hernández-Lloreda, Victoria; Call, Josep; Colmenares, Fernando

    2013-06-01

    Numerous studies have documented the ability of many species to make relative quantity judgments using an analogue magnitude system. We investigated whether one beluga whale, Delphinapterus leucas, and three bottlenose dolphins, Tursiops truncatus, were capable of selecting the larger of two sets of quantities, and analyzed if their performance matched predictions from the object file model versus the analog accumulator model. In Experiment 1, the two sets were presented simultaneously, under water, and they were visually (condition 1) or echoically (condition 2) available at the time of choice. In experiment 2, the two sets were presented above the water, successively (condition 1) or sequentially, item-by-item (condition 2), so that they were not visually available at the time of choice (condition 1) or at any time throughout the experiment (condition 2). We analyzed the effect of the ratio between quantities, the difference between quantities, and the total number of items presented on the subjects' choices. All subjects selected the larger of the two sets of quantities above chance levels in all conditions. However, unlike most previous studies, the subjects' choices did not match the predictions from the accumulator model. Whether these findings reflect interspecies differences in the mechanisms which underpin relative quantity judgments remains to be determined. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. How the great apes (Pan troglodytes, Pongo pygmaeus, Pan paniscus, Gorilla gorilla) perform on the reversed reward contingency task II: transfer to new quantities, long-term retention, and the impact of quantity ratios.

    PubMed

    Uher, Jana; Call, Josep

    2008-05-01

    We tested 6 chimpanzees (Pan troglodytes), 3 orangutans (Pongo pygmaeus), 4 bonobos (Pan paniscus), and 2 gorillas (Gorilla gorilla) in the reversed reward contingency task. Individuals were presented with pairs of quantities ranging between 0 and 6 food items. Prior to testing, some experienced apes had solved this task using 2 quantities while others were totally naïve. Experienced apes transferred their ability to multiple-novel pairs after 6 to 19 months had elapsed since their initial testing. Two out of 6 naïve apes (1 chimpanzee, 1 bonobo) solved the task--a proportion comparable to that of a previous study using 2 pairs of quantities. Their acquisition speed was also comparable to the successful subjects from that study. The ratio between quantities explained a large portion of the variance but affected naïve and experienced individuals differently. For smaller ratios, naïve individuals were well below 50% correct and experienced ones were well above 50%, yet both groups tended to converge toward 50% for larger ratios. Thus, some apes require no procedural modifications to overcome their strong bias for selecting the larger of 2 quantities. PsycINFO Database Record (c) 2008 APA, all rights reserved.

  5. Comparison of satellite derived dynamical quantities in the stratosphere of the Southern Hemisphere

    NASA Technical Reports Server (NTRS)

    Miles, Thomas (Editor); Oneill, Alan (Editor)

    1989-01-01

    The proceedings are summarized from a pre-MASH planning workshop on the intercomparison of Southern Hemisphere observations, analyses and derived dynamical quantities held in Williamsburg, Virginia during April 1986. The aims of this workshop were primarily twofold: (1) comparison of Southern Hemisphere dynamical quantities derived from various satellite data archives (e.g., from limb scanners and nadir sounders); and (2) assessing the impact of different base-level height information on such derived quantities. These tasks are viewed as especially important in the Southern Hemisphere because of the paucity of conventional measurements. A further strong impetus for the MASH program comes from the recent discovery of the springtime ozone hold over Antarctica. Insight gained from validation studies such as the one reported here will contribute to an improved understanding of the role of meteorology in the development and evolution of the hold, in its interannual variability, and in its interhemispheric differences. The dynamical quantities examined in this workshop included geopotential height, zonal wind, potential vorticity, eddy heat and momentum fluxes, and Eliassen-Palm fluxes. The time periods and data sources constituting the MASH comparisons are summarized.

  6. Comparison of satellite-derived dynamical quantities for the stratosphere of the Southern Hemisphere

    NASA Technical Reports Server (NTRS)

    Miles, Thomas (Editor); Oneill, Alan (Editor)

    1989-01-01

    As part of the international Middle Atmosphere Program (MAP), a project was instituted to study the dynamics of the Middle Atmosphere in the Southern Hemisphere (MASH). A pre-MASH workshop was held with two aims: comparison of Southern Hemisphere dynamical quantities derived from various archives of satellite data; and assessing the impact of different base-level height information on such derived quantities. The dynamical quantities examined included geopotential height, zonal wind, potential vorticity, eddy heat and momentum fluxes, and Eliassen-Palm fluxes. It was found that while there was usually qualitative agreement between the different sets of fields, substantial quantitative differences were evident, particularly in high latitudes. The fidelity of the base-level analysis was found to be of prime importance in calculating derived quantities - especially the Eliassen-Palm flux divergence and potential vorticity. Improvements in base-level analyses are recommended. In particular, quality controls should be introduced to remove spurious localized features from analyses, and information from all Antarctic radiosondes should be utilized where possible. Caution in drawing quantitative inferences from satellite data for the middle atmosphere of the Southern Hemisphere is advised.

  7. Chimpanzees Sometimes See Fuller as Better: Judgments of Food Quantities Based on Container Size and Fullness

    PubMed Central

    Parrish, Audrey E.; Beran, Michael J.

    2014-01-01

    The context in which food is presented can alter quantity judgments leading to sub-optimal choice behavior. Humans often over-estimate food quantity on the basis of how food is presented. Food appears larger if plated on smaller dishes than larger dishes and liquid volumes appear larger in taller cups than shorter cups. Moreover, smaller but fuller containers are preferred in comparison to larger, but less full containers with a truly larger quantity. Here, we assessed whether similar phenomena occur in chimpanzees. Four chimpanzees chose between two amounts of food presented in different sized containers, a large (2 oz.) and small (1 oz.) cup. When different quantities were presented in the same-sized cups or when the small cup contained the larger quantity, chimpanzees were highly accurate in choosing the larger food amount. However, when different-sized cups contained the same amount of food or the smaller cup contained the smaller amount of food (but looked relatively fuller), the chimpanzees often showed a bias to select the smaller but fuller cup. These findings contribute to our understanding of how quantity estimation and portion judgment is impacted by the surrounding context in which it is presented. PMID:24374384

  8. Determination of Micro-Quantities of Chrysotile Asbestos by Dye Adsorption

    ERIC Educational Resources Information Center

    Markham, M. Clare; Wosczyna, Karen

    1976-01-01

    Airborne asbestos is analyzed by differential dye adsorption. Quantities can be estimated down to 100 mg. For industrial use, asbestos samples must be separated from interfering minerals by density flotation. (Author/BT)

  9. 41 CFR 101-26.507-4 - Quantities in excess of the maximum order limitation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Quantities in excess of... Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND PROGRAM 26.5-GSA Procurement Programs § 101-26.507-4 Quantities in...

  10. Quantity and Quality of Motivational Regulation among University Students

    ERIC Educational Resources Information Center

    Engelschalk, Tobias; Steuer, Gabriele; Dresel, Markus

    2017-01-01

    Effective regulation of motivation can be theoretically explained by both the extent of motivational regulation strategies used (quantity) and their optimal implementation (quality). Researchers have not yet analysed the significance of both aspects for learning success simultaneously. In the present study, 188 students were presented with…

  11. Quantity, Quality, and Satisfaction with Mentoring: What Matters Most?

    ERIC Educational Resources Information Center

    Xu, Xiaohong; Payne, Stephanie C.

    2014-01-01

    According to Kram's mentor role theory, satisfaction with mentoring and mentorship quality are key indicators of effective and successful mentoring. We contribute to mentoring research by demonstrating the relative importance of mentorship quantity, mentorship quality, and satisfaction with mentoring to the prediction of job satisfaction,…

  12. Unraveling water quality and quantity effects of biofuels production

    USDA-ARS?s Scientific Manuscript database

    Developing a sustainable biofuels industry is crucial for several reasons, but what impact will it have on soil water quantity and quality? This popular press article for ISU alumni, teachers, middle/high school students and others is written to help them understand the complexity of this seemingly ...

  13. Pharmaceutical quantities of yohimbine found in dietary supplements in the USA.

    PubMed

    Cohen, Pieter A; Wang, Yan-Hong; Maller, Gregory; DeSouza, Renan; Khan, Ikhlas A

    2016-01-01

    In the USA, botanical dietary supplements are presumed to be safe, but this is not necessarily always the case. Extracts of the evergreen tree yohimbe, Pausinystalia johimbe, though banned in many countries, are sold in hundreds of dietary supplements in the USA. We analyzed 49 brands of supplements labelled as containing yohimbe or yohimbine available for sale from seven major retailers in the USA. Supplements were analyzed using ultra high-performance liquid chromatography coupled to photodiode and quadrupole time-of-flight mass spectrometry detectors for quantity of three alkaloids found in P. johimbe (yohimbine, rauwolscine, and corynanthine). The alkaloids were confirmed on the basis of retention time, ultraviolet spectra, and mass spectra against reference standards. The quantity of the most active alkaloid, yohimbine, per recommended serving ranged from none detected to 12.1 mg. Thirty-nine percent of the supplements (19/49) did not contain rauwolscine and corynanthine suggesting that the yohimbine was either from highly processed plant extract or synthetic in origin. Only 11 supplement brands (22%, 11/49) listed a specific quantity of yohimbine on the label. Most of these were inaccurately labelled (actual content ranged from 23% to 147% of the content on the label). Eighteen percent (9/49) of the supplements' labels did not provide any information about yohimbine's adverse effects. Of the 49 yohimbine supplement brands sold at seven major retail chains in the USA, only 4.1% (2/49) provided consumers with both accurate information about the quantity of yohimbine as well as information about yohimbine's known adverse effects. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

  14. 10 CFR Appendix C to Part 20 - Quantities 1 of Licensed Material Requiring Labeling

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 1 2014-01-01 2014-01-01 false Quantities 1 of Licensed Material Requiring Labeling C Appendix C to Part 20 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Pt. 20, App. C Appendix C to Part 20—Quantities 1 of Licensed Material Requiring Labeling Radionuclide...

  15. 10 CFR Appendix C to Part 20 - Quantities 1 of Licensed Material Requiring Labeling

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 1 2013-01-01 2013-01-01 false Quantities 1 of Licensed Material Requiring Labeling C Appendix C to Part 20 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Pt. 20, App. C Appendix C to Part 20—Quantities 1 of Licensed Material Requiring Labeling Radionuclide...

  16. 10 CFR Appendix C to Part 20 - Quantities 1 of Licensed Material Requiring Labeling

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Quantities 1 of Licensed Material Requiring Labeling C Appendix C to Part 20 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Pt. 20, App. C Appendix C to Part 20—Quantities 1 of Licensed Material Requiring Labeling Radionuclide...

  17. 10 CFR Appendix C to Part 20 - Quantities 1 of Licensed Material Requiring Labeling

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 1 2011-01-01 2011-01-01 false Quantities 1 of Licensed Material Requiring Labeling C Appendix C to Part 20 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Pt. 20, App. C Appendix C to Part 20—Quantities 1 of Licensed Material Requiring Labeling Radionuclide...

  18. Quality versus Quantity Debate in Swimming: Perceptions and Training Practices of Expert Swimming Coaches.

    PubMed

    Nugent, Frank J; Comyns, Thomas M; Warrington, Giles D

    2017-06-01

    The debate over low-volume, high-intensity training versus high-volume, low-intensity training, commonly known as Quality versus Quantity, respectively, is a frequent topic of discussion among swimming coaches and academics. The aim of this study was to explore expert coaches' perceptions of quality and quantity coaching philosophies in competitive swimming and to investigate their current training practices. A purposeful sample of 11 expert swimming coaches was recruited for this study. The study was a mixed methods design and involved each coach participating in 1 semi-structured interview and completing 1 closed-ended questionnaire. The main findings of this study were that coaches felt quality training programmes would lead to short term results for youth swimmers, but were in many cases more appropriate for senior swimmers. The coaches suggested that quantity training programmes built an aerobic base for youth swimmers, promoted technical development through a focus on slower swimming and helped to enhance recovery from training or competition. However, the coaches continuously suggested that quantity training programmes must be performed with good technique and they felt this was a misunderstood element. This study was a critical step towards gaining a richer and broader understanding on the debate over Quality versus Quantity training from an expert swimming coaches' perspective which was not currently available in the research literature.

  19. Quality versus Quantity Debate in Swimming: Perceptions and Training Practices of Expert Swimming Coaches

    PubMed Central

    Nugent, Frank J; Comyns, Thomas M; Warrington, Giles D

    2017-01-01

    Abstract The debate over low-volume, high-intensity training versus high-volume, low-intensity training, commonly known as Quality versus Quantity, respectively, is a frequent topic of discussion among swimming coaches and academics. The aim of this study was to explore expert coaches’ perceptions of quality and quantity coaching philosophies in competitive swimming and to investigate their current training practices. A purposeful sample of 11 expert swimming coaches was recruited for this study. The study was a mixed methods design and involved each coach participating in 1 semi-structured interview and completing 1 closed-ended questionnaire. The main findings of this study were that coaches felt quality training programmes would lead to short term results for youth swimmers, but were in many cases more appropriate for senior swimmers. The coaches suggested that quantity training programmes built an aerobic base for youth swimmers, promoted technical development through a focus on slower swimming and helped to enhance recovery from training or competition. However, the coaches continuously suggested that quantity training programmes must be performed with good technique and they felt this was a misunderstood element. This study was a critical step towards gaining a richer and broader understanding on the debate over Quality versus Quantity training from an expert swimming coaches’ perspective which was not currently available in the research literature. PMID:28713467

  20. Effect of the self-pumped limiter concept on the tritium fuel cycle

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Finn, P.A.; Sze, D.K.; Hassanein, A.

    1988-01-01

    The self-pumped limiter concept for impurity control of the plasma of a fusion reactor has a major impact on the design of the tritium systems. To achieve a sustained burn, conventional limiters and divertors remove large quantities of unburnt tritium and deuterium from the plasma which must be then recycled using a plasma processing system. The self-pumped limiter which does not remove the hydrogen species, does not require any plasma processing equipment. The blanket system and the coolant processing systems acquire greater importance with the use of this unconventional impurity control system. 3 refs., 2 figs.

  1. 48 CFR 52.207-4 - Economic Purchase Quantity-Supplies.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Economic Purchase Quantity....207-4 Economic Purchase Quantity—Supplies. As prescribed in 7.203, insert the following provision: Economic Purchase Quantity—Supplies (AUG 1987) (a) Offerors are invited to state an opinion on whether the...

  2. 46 CFR 108.433 - Quantity of CO2: General.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Quantity of CO2: General. 108.433 Section 108.433 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Fire Extinguishing Systems Fixed Carbon Dioxide Fire Extinguishing Systems § 108.433...

  3. 46 CFR 108.433 - Quantity of CO2: General.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Quantity of CO2: General. 108.433 Section 108.433 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Fire Extinguishing Systems Fixed Carbon Dioxide Fire Extinguishing Systems § 108.433...

  4. 46 CFR 108.433 - Quantity of CO2: General.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Quantity of CO2: General. 108.433 Section 108.433 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Fire Extinguishing Systems Fixed Carbon Dioxide Fire Extinguishing Systems § 108.433...

  5. 48 CFR 52.207-4 - Economic Purchase Quantity-Supplies.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 2 2012-10-01 2012-10-01 false Economic Purchase Quantity....207-4 Economic Purchase Quantity—Supplies. As prescribed in 7.203, insert the following provision: Economic Purchase Quantity—Supplies (AUG 1987) (a) Offerors are invited to state an opinion on whether the...

  6. 48 CFR 52.207-4 - Economic Purchase Quantity-Supplies.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 2 2011-10-01 2011-10-01 false Economic Purchase Quantity....207-4 Economic Purchase Quantity—Supplies. As prescribed in 7.203, insert the following provision: Economic Purchase Quantity—Supplies (AUG 1987) (a) Offerors are invited to state an opinion on whether the...

  7. 48 CFR 52.207-4 - Economic Purchase Quantity-Supplies.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 2 2014-10-01 2014-10-01 false Economic Purchase Quantity....207-4 Economic Purchase Quantity—Supplies. As prescribed in 7.203, insert the following provision: Economic Purchase Quantity—Supplies (AUG 1987) (a) Offerors are invited to state an opinion on whether the...

  8. 48 CFR 52.207-4 - Economic Purchase Quantity-Supplies.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 2 2013-10-01 2013-10-01 false Economic Purchase Quantity....207-4 Economic Purchase Quantity—Supplies. As prescribed in 7.203, insert the following provision: Economic Purchase Quantity—Supplies (AUG 1987) (a) Offerors are invited to state an opinion on whether the...

  9. 16 CFR 300.28 - Undetermined quantities of reclaimed fibers.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 1 2011-01-01 2011-01-01 false Undetermined quantities of reclaimed fibers. 300.28 Section 300.28 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS RULES AND REGULATIONS UNDER THE WOOL PRODUCTS LABELING ACT OF 1939 Labeling § 300.28 Undetermined...

  10. A colorimeter for measurement of picomole quantities of urea.

    PubMed

    Vurek, G G; Knepper, M A

    1982-04-01

    We described a new colorimeter for the measurement of picomole quantities of urea in nanoliter volume fluid samples. The diacetyl monoxime reaction was used to produce a colored product from urea. The method is capable of resolving differences of 10 pmoles between samples containing 0 to 225 pmoles.

  11. 49 CFR 173.306 - Limited quantities of compressed gases.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... transportation and transported in accordance with the applicable provisions of this subchapter in effect on... recycling or disposal. Aerosols, as defined in § 171.8 of this subchapter, containing a limited quantity... purposes of recycling or disposal under the following conditions: (1) The strong outer packaging and its...

  12. 19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 2 2011-04-01 2011-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

  13. 19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

  14. Disasters and Impact of Sleep Quality and Quantity on National Guard Medical Personnel

    DTIC Science & Technology

    2018-04-30

    Impact of Sleep Quality & Quantity on National Guard Medical Personnel Sb. GRANT NUMBER Sc. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Sd. PROJECT NUMBER...Std. 239.18 Adobe Professional 7 .0 Approved for Public Release ~••Unlmlted Disasters & Impact of Sleep Quality & Quantity on National Guard...College of Nursing 4/11/2018 6 Methods • Measures • Critical skills questions • Medication calculations +Licensed • Basic Life Support (BLS

  15. A review of implicit and explicit substance self-concept as a predictor of alcohol and tobacco use and misuse.

    PubMed

    Lindgren, Kristen P; Neighbors, Clayton; Gasser, Melissa L; Ramirez, Jason J; Cvencek, Dario

    2017-05-01

    This paper provides an overview of the self-concept as it relates to substance use. Self-concept has a long history in psychological theory and research; however, substance self-concept (e.g., viewing one's self as a drinker or smoker) is an understudied area of research with the potential to expand existing conceptualizations of substance use, addiction, and prevention and treatment efforts, and should receive greater research attention. First, we review and provide a theoretical framework of substance self-concept that draws from dual process models and distinguishes between implicit and explicit self-concept. Next, we summarize key findings related to substance use in the extant literature, focusing on alcohol and tobacco (smoking). Across both substances, there is converging evidence that substance self-concept is associated with substance use outcomes, including quantity and frequency of use and problems associated with use, and that change in substance self-concept is associated with recovery from substance misuse. Recommendations for the substance self-concept research agenda include routine assessment of substance self-concept, expanded use of implicit measures, investigation of moderators of substance self-concept, and targeting substance self-concept directly in prevention and intervention efforts. Ultimately, we suggest that substance self-concept is a promising, but understudied, construct. Greater research attention to substance self-concept could clarify its potential as an important risk factor for hazardous use and addiction as well as its utility as a prevention and treatment target.

  16. A review of implicit and explicit substance self-concept as a predictor of alcohol and tobacco use and misuse

    PubMed Central

    Lindgren, Kristen P.; Neighbors, Clayton; Gasser, Melissa L.; Ramirez, Jason J.; Cvencek, Dario

    2017-01-01

    Background This paper provides an overview of the self-concept as it relates to substance use. Self-concept has a long history in psychological theory and research; however, substance self-concept (e.g., viewing one’s self as a drinker or smoker) is an understudied area of research with the potential to expand existing conceptualizations of substance use, addiction, and prevention and treatment efforts, and should receive greater research attention. Objectives First, we review and provide a theoretical framework of substance self-concept that draws from dual process models and distinguishes between implicit and explicit self-concept. Next, we summarize key findings related to substance use in the extant literature, focusing on alcohol and tobacco (smoking). Results Across both substances, there is converging evidence that substance self-concept is associated with substance use outcomes, including quantity and frequency of use and problems associated with use, and that change in substance self-concept is associated with recovery from substance misuse. Recommendations for the substance self-concept research agenda include routine assessment of substance self-concept, expanded use of implicit measures, investigation of moderators of substance self-concept, and targeting substance self-concept directly in prevention and intervention efforts. Conclusion Ultimately, we suggest that substance self-concept is a promising, but understudied, construct. Greater research attention to substance self-concept could clarify its potential as an important risk factor for hazardous use and addiction as well as its utility as a prevention and treatment target. PMID:27715328

  17. Balancing Teacher Quality and Quantity

    NASA Astrophysics Data System (ADS)

    Bond, Helen

    The world is facing a shortage of trained teachers. According to the 2010 Global Monitoring Report approximately 10.3 million teachers will be needed globally to staff classrooms from Bangkok to Canada. The situation is worse in Sub-Saharan Africa. Estimates suggest that approximately 1.2 million new teachers will be needed in Sub-Saharan Africa alone to achieve universal primary education goals by 2015. Increases in primary school enrollments, drought, and HIV-AIDS have exacerbated the need for well trained teachers. Despite the need, the focus is on balancing quality with quantity. An effective teacher is deemed a critical element, although not the only one, in a student's success in the classroom. This paper focuses on the dilemma of meeting universal primary education goals in Sub-Saharan Africa, while maintaining teacher quality in fragile contexts.

  18. Conserved quantities in non-Abelian monopole fields

    NASA Astrophysics Data System (ADS)

    Horváthy, P. A.; Ngome, J.-P.

    2009-06-01

    Van Holten’s covariant Hamiltonian framework is used to find conserved quantities for an isospin-carrying particle in a non-Abelian monopolelike field. For a Wu-Yang monopole we find the most general scalar potential such that the combined system admits a conserved Runge-Lenz vector. In the effective non-Abelian field for nuclear motion in a diatomic molecule due to Moody, Shapere, and Wilczek, a conserved angular momentum is constructed, despite the nonconservation of the electric charge. No Runge-Lenz vector has been found.

  19. Electric Propulsion Concepts Enabled by High Power Systems for Space Exploration

    NASA Technical Reports Server (NTRS)

    Gilland, James; Fiehler, Douglas; Lyons, Valerie

    2005-01-01

    This paper describes the latest development in electric propulsion systems being planned for the new Space Exploration initiative. Missions to the Moon and Mars will require these new thrusters to deliver the large quantities of supplies that would be needed to support permanent bases on other worlds. The new thrusters are also being used for unmanned exploration missions that will go to the far reaches of the solar system. This paper is intended to give the reader some insight into several electric propulsion concepts their operating principles and capabilities, as well as an overview of some mission applications that would benefit from these propulsion systems, and their accompanying advanced power systems.

  20. David Hume's Monetary Theory Revisited: Was He Really a Quantity Theorist and an Inflationist?

    ERIC Educational Resources Information Center

    Wennerlind, Carl

    2005-01-01

    David Hume's monetary theory has been controversial since its formulation. Lately, the focus has been on Hume's alleged misapplication of the quantity theory of money. While he appears to subscribe to a simple quantity theory with money neutrality, in a famously contested passage in the essay Of Money, he violates the neutrality condition by…

  1. VizieR Online Data Catalog: Thermodynamic quantities of molecular hydrogen (Popovas+, 2016)

    NASA Astrophysics Data System (ADS)

    Popovas, A.; Jorgensen, U. G.

    2016-07-01

    New partition functions for equilibrium, normal, and ortho and para hydrogen are calculated and thermodynamic quantities are reported for the temperature range 1-20000K. Our results are compared to previous estimates in the literature. The calculations are not limited to the ground electronic state, but include all bound and quasi-bound levels of excited electronic states. Dunham coefficients of these states of H2 are also reported. Reported internal partition functions and thermodynamic quantities in the present work are shown to be more accurate than previously available data. (4 data files).

  2. Number versus Continuous Quantity in Numerosity Judgments by Fish

    ERIC Educational Resources Information Center

    Agrillo, Christian; Piffer, Laura; Bisazza, Angelo

    2011-01-01

    In quantity discrimination tasks, adults, infants and animals have been sometimes observed to process number only after all continuous variables, such as area or density, have been controlled for. This has been taken as evidence that processing number may be more cognitively demanding than processing continuous variables. We tested this hypothesis…

  3. Water quantity and quality at the urban-rural interface

    Treesearch

    Ge Sun; B. Graeme Lockaby

    2012-01-01

    Population growth and urban development dramatically alter natural watershed ecosystem structure and functions and stress water resources. We review studies on the impacts of urbanization on hydrologic and biogeochemical processes underlying stream water quantity and water quality issues, as well as water supply challenges in an urban environment. We conclude that...

  4. 19 CFR 144.32 - Statement of quantity; charges and liens.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... shall have indicated thereon, preferably in the lower part of the left-hand margin if there is no space... statement shall indicate: (1) The quantity (i.e., the number of outer containers, or tons, etc.) in the...

  5. 19 CFR 144.32 - Statement of quantity; charges and liens.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... shall have indicated thereon, preferably in the lower part of the left-hand margin if there is no space... statement shall indicate: (1) The quantity (i.e., the number of outer containers, or tons, etc.) in the...

  6. 19 CFR 144.32 - Statement of quantity; charges and liens.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... shall have indicated thereon, preferably in the lower part of the left-hand margin if there is no space... statement shall indicate: (1) The quantity (i.e., the number of outer containers, or tons, etc.) in the...

  7. 21 CFR 801.62 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... panel. (p) A separate statement of net quantity of contents in terms of the metric system of weight or... contents in terms of the metric system of weight or measure may also appear on the principal display panel...

  8. 21 CFR 201.62 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... panel. (p) A separate statement of net quantity of contents in terms of the metric system of weight or... contents in terms of the metric system of weight or measure may also appear on the principal display panel...

  9. Observational Learning of Quantity Conservation and Piagetian Generalization Tasks

    ERIC Educational Resources Information Center

    Charbonneau, Claude; And Others

    1976-01-01

    Twenty first-graders observed an adult model perform a quantity conservation task. The children were then tested on a series of generalization tasks immediately, after one week, and after three months. The results suggested that the social experience of observation appeared to activate a cognitive restructuring of the children's mental operations.…

  10. Predictors of Sleep Quantity and Quality in College Students

    ERIC Educational Resources Information Center

    Davidson, Eric S.

    2012-01-01

    Whereas sleep is often thought of as a common health issue among college students, few, if any, researchers have comprehensively evaluated correlates and predictors of sleep quality and quantity within this population. Most often, studies of this type are used by researchers to assess particular categories of correlates and predictors (e.g.,…

  11. TYPES AND QUANTITIES OF LEFTOVER DRUGS ...

    EPA Pesticide Factsheets

    BACKGROUND: Pharmaceuticals designed for humans and animals often remain unused. Leftover and accumulated drugs represent suboptimal delivery of health care and environmentally unsound disposal, which can pose exposure risks for humans and wildlife.OBJECTIVES: A major unknown with respect to drugs as pollutants is what fractions of drug residues occurring in the ambient environment result from discarding leftover drugs. To gauge the significance of leftover drugs as potential pollutants, data are needed on the types, quantities, and frequencies with which drugs accumulate. Absence of this data has prevented assessments of the significance of drug accumulation and disposal as a contributing source of drug residues in the environment.METHODS: One particular source of drug accumulation is those drugs that become

  12. The pluralistic water research concept - a new human-water system research approach

    NASA Astrophysics Data System (ADS)

    Evers, Mariele; Höllermann, Britta; Almoradie, Adrian; Taft, Linda; Garcia-Santos, Glenda

    2017-04-01

    Sustainable water resources management has been and still is a main challenge for decision makers even though for the past number of decades integrative approaches and concepts (e.g. Integrated Water Resources Management - IWRM) have been developed to address problems on floods, droughts, water quality, water quantity, environment and ecology. Although somehow these approaches are aiming to address water related problems in an integrative approach and to some extent include or involve society in the planning and management, they still lack some of the vital components in including the social dimensions and their interaction with water. Understanding these dynamics in a holistic way and how they are shaped by time and space may tackle these shortcomings and provide more effective and sustainable management solutions with respect to a set of potential present social actions and values as well as possible futures. This paper aims to discuss challenges to coherently and comprehensively integrate the social dimensions of different human-water concepts like IWRM, socio-hydrology and waterscape. Against this background it will develop criteria for an integrative approach and present a newly developed concept termed pluralistic water research (PWR) concept. PWR is not only a pluralistic but also an integrative and interdisciplinary approach to acknowledge the social and water dimensions and their interaction and dynamics by considering more than one perspective of a water-related issue, hereby providing a set of multiple (future) developments. Our PWR concept will be illustrated by a case study application of the Canary island La Gomera. Furthermore an outlook on further possible developments of the PWR concept will be presented and discussed.

  13. Central distractors in Force Concept Inventory data

    NASA Astrophysics Data System (ADS)

    Scott, Terry F.; Schumayer, Dániel

    2018-01-01

    The Force Concept Inventory was designed to poll the Newtonian conception of force. While there are many in-depth studies analyzing response data that look at the structure of the correct answers, we believe that the incorrect answers also carry revealing information about the students' worldview. The inventory was originally designed so that the "distractors" in each question reflected commonly held misconceptions, and thus the rate at which students guess the correct answer is very low. Students select incorrect answers that correspond to the misconception that they hold and there are very few responses which appear obviously wrong to students. A side effect of this approach is that the incorrect responses reflect the non-Newtonian worldviews held by students. These non-Newtonian worldviews are coherent and robust, and this, at least in part, helps to explain why these misconceptions are so resistant to instruction. In this study we focus once more on the misconception data in Force Concept Inventory responses, particularly on the linkages between these misconceptions. We hypothesize that there are distinct groupings of distractor items formed by the strength of the association between these items. The two largest groupings are associated with the "impetus" world view in which the motion of an object is determined by the quantity of impetus which that object contains. We find that certain central items hold particularly important places in these groupings and also that individual groupings may be connected to each other by "connector" items. We finally suggest that, on the basis of this study, that these non-Newtonian worldviews might best be dismantled by addressing these key central and connector items.

  14. 21 CFR 801.62 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... statement of net quantity of contents in terms of the metric system of weight or measure is not regarded as... metric system of weight or measure may also appear on the principal display panel or on other panels. (q...

  15. Bulky waste quantities and treatment methods in Denmark.

    PubMed

    Larsen, Anna W; Petersen, Claus; Christensen, Thomas H

    2012-02-01

    Bulky waste is a significant and increasing waste stream in Denmark. However, only little research has been done on its composition and treatment. In the present study, data about collection methods, waste quantities and treatment methods for bulky waste were obtained from two municipalities. In addition a sorting analysis was conducted on combustible waste, which is a major fraction of bulky waste in Denmark. The generation of bulky waste was found to be 150-250 kg capita(-1) year(-1), and 90% of the waste was collected at recycling centres; the rest through kerbside collection. Twelve main fractions were identified of which ten were recyclable and constituted 50-60% of the total quantity. The others were combustible waste for incineration (30-40%) and non-combustible waste for landfilling (10%). The largest fractions by mass were combustible waste, bricks and tile, concrete, non-combustible waste, wood, and metal scrap, which together made up more than 90% of the total waste amounts. The amount of combustible waste could be significantly reduced through better sorting. Many of the waste fractions consisted of composite products that underwent thorough separation before being recycled. The recyclable materials were in many cases exported to other countries which made it difficult to track their destination and further treatment.

  16. 10 CFR 40.22 - Small quantities of source material.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 1 2014-01-01 2014-01-01 false Small quantities of source material. 40.22 Section 40.22 Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF SOURCE MATERIAL General Licenses § 40.22 Small... (15.4 lb) of uranium, removed during the treatment of drinking water, at any one time. A person may...

  17. How Do Our Actions Affect Water Quantity and Quality?

    ERIC Educational Resources Information Center

    Gordon, Jessica

    2008-01-01

    Water is an essential resource for all living things. How we live on our watershed can impact water quantity and quality. It is important to recognize how humans alter watershed dynamics, but students often find it challenging to visualize watershed processes and understand how decisions that they make as individuals and together as a community…

  18. A Weight of Evidence Framework for Environmental Assessments: Inferring Quantities

    EPA Science Inventory

    Environmental assessments require the generation of quantitative parameters such as degradation rates and assessment products may be quantities such as criterion values or magnitudes of effects. When multiple data sets or outputs of multiple models are available, it may be appro...

  19. Buyer-vendor coordination for fixed lifetime product with quantity discount under finite production rate

    NASA Astrophysics Data System (ADS)

    Zhang, Qinghong; Luo, Jianwen; Duan, Yongrui

    2016-03-01

    Buyer-vendor coordination has been widely addressed; however, the fixed lifetime of the product is seldom considered. In this paper, we study the coordination of an integrated production-inventory system with quantity discount for a fixed lifetime product under finite production rate and deterministic demand. We first derive the buyer's ordering policy and the vendor's production batch size in decentralised and centralised systems. We then compare the two systems and show the non-coordination of the ordering policies and the production batch sizes. To improve the supply chain efficiency, we propose quantity discount contract and prove that the contract can coordinate the buyer-vendor supply chain. Finally, we present analytically tractable solutions and give a numerical example to illustrate the benefits of the proposed quantity discount strategy.

  20. 75 FR 82069 - Ethyl Alcohol for Fuel Use: Determination of the Base Quantity of Imports

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-29

    ...: Determination of the Base Quantity of Imports AGENCY: United States International Trade Commission. ACTION... establish the ``base quantity'' of imports of fuel ethyl alcohol with a zero percent local feedstock requirement that can be imported from U.S. insular possessions or CBERA-beneficiary countries. The base...

  1. An economic order quantity model with shortage and inflation

    NASA Astrophysics Data System (ADS)

    Wulan, Elis Ratna; Nurjaman, Wildan

    2015-09-01

    The effect of inflation has become a persistent characteristic and more significant problem of many developing economies especially in the third world countries. While making effort to achieve optimal quantity of product to be produced or purchased using the simplest and on the shelf classical EOQ model, the non-inclusion of conflicting economic realities as shortage and inflation has rendered its result quite uneconomical and hence the purpose for this study. Mathematical expression was developed for each of the cost components the sum of which become the total inventory model over the period (0,L) ((TIC(0,L)). L is planning horizon and TIC(0,L) is total inventory cost over a period of (0,L). Significant savings with increase in quantity was achieved based on deference in the varying price regime. With the assumptions considered and subject to the availability of reliable inventory cost element, the developed model is found to produce a feasible, and economic inventory stock-level with the numerical example of a material supply of a manufacturing company.

  2. Assessing quantities and disposal routes for household hazardous products in the United Kingdom.

    PubMed

    Slack, Rebecca J; Zerva, Panagoula; Gronow, Jan R; Voulvoulis, Nikolaos

    2005-03-15

    The disposal of household products containing hazardous substances (household hazardous wastes; HHW) is of concern due to possible health and environmental effects as a consequence of environmental pollution. The potential risks of disposal are proportional to the amounts of products used and waste generated, but much of the data relating to quantities are old, inconsistent, or nonexistent. Hence, full-scale risk assessment is not yet feasible. This pilot study was aimed at an initial assessment of the amounts of hazardous products used or stored within the household and potential disposal routes. Representatives of 400 households from southeast England were interviewed about socio-demographic factors, perception of the risks associated with the use and disposal of hazardous waste generated in households, quantities of particular products currently in use or stored within the household, and times and methods of disposal of such products. The estimates of quantities obtained were compared with sales figures and waste estimates to improve understanding of product flow through to the HHW stream. The disposal routes investigated demonstrated that most householders claim to use the entire product priorto disposal in the general refuse bin. The relationship with socio-demographic factors demonstrated a difference between neighborhood size and length of residence in a household with regard to product quantities possessed and the disposal habits adopted.

  3. Can the Lorenz-Gauge Potentials Be Considered Physical Quantities?

    ERIC Educational Resources Information Center

    Heras, Jose A.; Fernandez-Anaya, Guillermo

    2010-01-01

    Two results support the idea that the scalar and vector potentials in the Lorenz gauge can be considered to be physical quantities: (i) they separately satisfy the properties of causality and propagation at the speed of light and do not imply spurious terms and (ii) they can naturally be written in a manifestly covariant form. In this paper we…

  4. 23 CFR 635.123 - Determination and documentation of pay quantities.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Determination and documentation of pay quantities. 635.123 Section 635.123 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS CONSTRUCTION AND MAINTENANCE Contract Procedures § 635.123 Determination and...

  5. 76 FR 9665 - Designation, Reportable Quantities, and Notification; Notification Requirements

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-02-22

    ... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 302 [EPA-HQ-SFUND-2010-1068; FRL-9268-8] Designation, Reportable Quantities, and Notification; Notification Requirements AGENCY: Environmental Protection Agency... knowledge of any release (other than a federally permitted release or application of a pesticide) for the...

  6. Aerobic digestion reduces the quantity of antibiotic resistance genes in residual municipal wastewater solids

    PubMed Central

    Burch, Tucker R.; Sadowsky, Michael J.; LaPara, Timothy M.

    2012-01-01

    Numerous initiatives have been undertaken to circumvent the problem of antibiotic resistance, including the development of new antibiotics, the use of narrow spectrum antibiotics, and the reduction of inappropriate antibiotic use. We propose an alternative but complimentary approach to reduce antibiotic resistant bacteria (ARB) by implementing more stringent technologies for treating municipal wastewater, which is known to contain large quantities of ARB and antibiotic resistance genes (ARGs). In this study, we investigated the ability of conventional aerobic digestion to reduce the quantity of ARGs in untreated wastewater solids. A bench-scale aerobic digester was fed untreated wastewater solids collected from a full-scale municipal wastewater treatment facility. The reactor was operated under semi-continuous flow conditions for more than 200 days at a residence time of approximately 40 days. During this time, the quantities of tet(A), tet(W), and erm(B) decreased by more than 90%. In contrast, intI1 did not decrease, and tet(X) increased in quantity by 5-fold. Following operation in semi-continuous flow mode, the aerobic digester was converted to batch mode to determine the first-order decay coefficients, with half-lives ranging from as short as 2.8 days for tet(W) to as long as 6.3 days for intI1. These results demonstrated that aerobic digestion can be used to reduce the quantity of ARGs in untreated wastewater solids, but that rates can vary substantially depending on the reactor design (i.e., batch vs. continuous-flow) and the specific ARG. PMID:23407455

  7. Aerobic digestion reduces the quantity of antibiotic resistance genes in residual municipal wastewater solids.

    PubMed

    Burch, Tucker R; Sadowsky, Michael J; Lapara, Timothy M

    2013-01-01

    Numerous initiatives have been undertaken to circumvent the problem of antibiotic resistance, including the development of new antibiotics, the use of narrow spectrum antibiotics, and the reduction of inappropriate antibiotic use. We propose an alternative but complimentary approach to reduce antibiotic resistant bacteria (ARB) by implementing more stringent technologies for treating municipal wastewater, which is known to contain large quantities of ARB and antibiotic resistance genes (ARGs). In this study, we investigated the ability of conventional aerobic digestion to reduce the quantity of ARGs in untreated wastewater solids. A bench-scale aerobic digester was fed untreated wastewater solids collected from a full-scale municipal wastewater treatment facility. The reactor was operated under semi-continuous flow conditions for more than 200 days at a residence time of approximately 40 days. During this time, the quantities of tet(A), tet(W), and erm(B) decreased by more than 90%. In contrast, intI1 did not decrease, and tet(X) increased in quantity by 5-fold. Following operation in semi-continuous flow mode, the aerobic digester was converted to batch mode to determine the first-order decay coefficients, with half-lives ranging from as short as 2.8 days for tet(W) to as long as 6.3 days for intI1. These results demonstrated that aerobic digestion can be used to reduce the quantity of ARGs in untreated wastewater solids, but that rates can vary substantially depending on the reactor design (i.e., batch vs. continuous-flow) and the specific ARG.

  8. Age-dependent biochemical quantities: an approach for calculating reference intervals.

    PubMed

    Bjerner, J

    2007-01-01

    A parametric method is often preferred when calculating reference intervals for biochemical quantities, as non-parametric methods are less efficient and require more observations/study subjects. Parametric methods are complicated, however, because of three commonly encountered features. First, biochemical quantities seldom display a Gaussian distribution, and there must either be a transformation procedure to obtain such a distribution or a more complex distribution has to be used. Second, biochemical quantities are often dependent on a continuous covariate, exemplified by rising serum concentrations of MUC1 (episialin, CA15.3) with increasing age. Third, outliers often exert substantial influence on parametric estimations and therefore need to be excluded before calculations are made. The International Federation of Clinical Chemistry (IFCC) currently recommends that confidence intervals be calculated for the reference centiles obtained. However, common statistical packages allowing for the adjustment of a continuous covariate do not make this calculation. In the method described in the current study, Tukey's fence is used to eliminate outliers and two-stage transformations (modulus-exponential-normal) in order to render Gaussian distributions. Fractional polynomials are employed to model functions for mean and standard deviations dependent on a covariate, and the model is selected by maximum likelihood. Confidence intervals are calculated for the fitted centiles by combining parameter estimation and sampling uncertainties. Finally, the elimination of outliers was made dependent on covariates by reiteration. Though a good knowledge of statistical theory is needed when performing the analysis, the current method is rewarding because the results are of practical use in patient care.

  9. Energy Drinks and Binge Drinking Predict College Students' Sleep Quantity, Quality, and Tiredness.

    PubMed

    Patrick, Megan E; Griffin, Jamie; Huntley, Edward D; Maggs, Jennifer L

    2018-01-01

    This study examines whether energy drink use and binge drinking predict sleep quantity, sleep quality, and next-day tiredness among college students. Web-based daily data on substance use and sleep were collected across four semesters in 2009 and 2010 from 667 individuals for up to 56 days each, yielding information on 25,616 person-days. Controlling for average levels of energy drink use and binge drinking (i.e., 4+ drinks for women, 5+ drinks for men), on days when students consumed energy drinks, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not use energy drinks. Similarly, on days when students binge drank, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not binge drink. There was no significant interaction effect between binge drinking and energy drink use on the outcomes.

  10. From electronic consumer products to e-wastes: Global outlook, waste quantities, recycling challenges.

    PubMed

    Tansel, Berrin

    2017-01-01

    Advancements in technology, materials development, and manufacturing processes have changed the consumer products and composition of municipal solid waste (MSW) since 1960s. Increasing quantities of discarded consumer products remain a major challenge for recycling efforts, especially for discarded electronic products (also referred as e-waste). The growing demand for high tech products has increased the e-waste quantities and its cross boundary transport globally. This paper reviews the challenges associated with increasing e-waste quantities. The increasing need for raw materials (especially for rare earth and minor elements) and unregulated e-waste recycling operations in developing and underdeveloped counties contribute to the growing concerns for e-waste management. Although the markets for recycled materials are increasing; there are major challenges for development of the necessary infrastructure for e-waste management and accountability as well as development of effective materials recovery technologies and product design. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. 40 CFR 227.9 - Limitations on quantities of waste materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... materials. 227.9 Section 227.9 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING CRITERIA FOR THE EVALUATION OF PERMIT APPLICATIONS FOR OCEAN DUMPING OF MATERIALS Environmental Impact § 227.9 Limitations on quantities of waste materials. Substances which may damage the ocean...

  12. 40 CFR 227.9 - Limitations on quantities of waste materials.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... materials. 227.9 Section 227.9 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING CRITERIA FOR THE EVALUATION OF PERMIT APPLICATIONS FOR OCEAN DUMPING OF MATERIALS Environmental Impact § 227.9 Limitations on quantities of waste materials. Substances which may damage the ocean...

  13. 40 CFR 227.9 - Limitations on quantities of waste materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... materials. 227.9 Section 227.9 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING CRITERIA FOR THE EVALUATION OF PERMIT APPLICATIONS FOR OCEAN DUMPING OF MATERIALS Environmental Impact § 227.9 Limitations on quantities of waste materials. Substances which may damage the ocean...

  14. 40 CFR 227.9 - Limitations on quantities of waste materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... materials. 227.9 Section 227.9 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING CRITERIA FOR THE EVALUATION OF PERMIT APPLICATIONS FOR OCEAN DUMPING OF MATERIALS Environmental Impact § 227.9 Limitations on quantities of waste materials. Substances which may damage the ocean...

  15. 40 CFR 227.9 - Limitations on quantities of waste materials.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... materials. 227.9 Section 227.9 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING CRITERIA FOR THE EVALUATION OF PERMIT APPLICATIONS FOR OCEAN DUMPING OF MATERIALS Environmental Impact § 227.9 Limitations on quantities of waste materials. Substances which may damage the ocean...

  16. Quality and Quantity of Applicants for Teacher Education Rapidly Diminishing.

    ERIC Educational Resources Information Center

    Starr, Nina K.

    1983-01-01

    Identifies two societal factors contributing to the decrease in quantity/quality of applicants for teacher education programs: range of career options now available for females and the "tunnel vision" mind set of schools, departments, and colleges of education. Suggests generic pedagogy as a solution. (MH)

  17. Management of Water Quantity and Quality Based on Copula for a Tributary to Miyun Reservoir, Beijing

    NASA Astrophysics Data System (ADS)

    Zang, N.; Wang, X.; Liang, P.

    2017-12-01

    Due to the complex mutual influence between water quantity and water quality of river, it is difficult to reflect the actual characters of the tributaries to reservoir. In this study, the acceptable marginal probability distributions for water quantity and quality of reservoir inflow were calculated. A bivariate Archimedean copula was further applied to establish the joint distribution function of them. Then multiple combination scenarios of water quantity and water quality were designed to analyze their coexistence relationship and reservoir management strategies. Taking Bai river, an important tributary into the Miyun Reservoir, as a study case. The results showed that it is feasible to apply Frank copula function to describe the jointed distribution function of water quality and water quantity for Bai river. Furthermore, the monitoring of TP concentration needs to be strengthen in Bai river. This methodology can be extended to larger dimensions and is transferable to other reservoirs via establishment of models with relevant data for a particular area. Our findings help better analyzing the coexistence relationship and influence degree of the water quantity and quality of the tributary to reservoir for the purpose of water resources protection.

  18. Quantity and quality benefits of in-service invasive cleaning of trunk mains

    NASA Astrophysics Data System (ADS)

    Sunny, Iftekhar; Husband, Stewart; Drake, Nick; Mckenzie, Kevan; Boxall, Joby

    2017-07-01

    Trunk mains are high risk critical infrastructure where poor performance can impact on large numbers of customers. Both quantity (e.g. hydraulic capacity) and quality (e.g. discolouration) of trunk main performance are affected by asset deterioration in the form of particle accumulation at the pipe wall. Trunk main cleaning techniques are therefore desirable to remove such material. However, little is quantified regarding the efficacy of different maintenance interventions or longer-term changes following such cleaning. This paper presents an assessment of quantity and quality performance of a trunk main system pre, post and for 12 months following cleaning using pigging with ice slurry. Hydraulic calibration showed a 7 times roughness height reduction after ice slurry pigging, evidencing substantially improved hydraulic capacity and reduced headloss. Turbidity response due to carefully imposed shear stress increase remained significant after the cleaning intervention, showing that relatively loose material had not been fully removed from the pipe wall. Overall the results demonstrate that cleaning by pigging with ice slurry can be beneficial for quantity performance, but care and further assessment may be necessary to realise the full quality benefits.

  19. The New Field Quantities and the Poynting Theorem in Material Medium with Magnetic Monopoles

    NASA Astrophysics Data System (ADS)

    Zor, Ömer

    2016-12-01

    The duality transformation was used to define the polarization mechanisms that arise from magnetic monopoles. Then, a dimensional analysis was conducted to describe the displacement and magnetic intensity vectors (constitutive equations) in SI units. Finally, symmetric Maxwell equations in a material medium with new field quantities were introduced. Hence, the Lorentz force and the Poynting theorem were defined with these new field quantities, and many possible definitions of them were constructed.

  20. Organizational citizenship behavior and the quantity and quality of work group performance.

    PubMed

    Podsakoff, P M; Ahearne, M; MacKenzie, S B

    1997-04-01

    Despite the widespread interest in the topic of organizational citizenship behaviors (OCBs), little empirical research has tested the fundamental assumption that these forms of behavior improve the effectiveness of work groups or organizations in which they are exhibited. In the present study, the effects of OCBs on the quantity and quality of the performance of 218 people working in 40 machine crews in a paper mill located in the Northeastern United States were examined. The results indicate that helping behavior and sportsmanship had significant effects on performance quantity and that helping behavior had a significant impact on performance quality. However, civic virtue had no effect on either performance measure.

  1. Relative quantity judgments between discrete spatial arrays by chimpanzees (Pan troglodytes) and New Zealand robins (Petroica longipes).

    PubMed

    Garland, Alexis; Beran, Michael J; McIntyre, Joseph; Low, Jason

    2014-08-01

    Quantity discrimination for items spread across spatial arrays was investigated in chimpanzees (Pan troglodytes) and North Island New Zealand robins (Petroica longipes), with the aim of examining the role of spatial separation on the ability of these 2 species to sum and compare nonvisible quantities which are both temporally and spatially separated, and to assess the likely mechanism supporting such summation performance. Birds and chimpanzees compared 2 sets of discrete quantities of items that differed in number. Six quantity comparisons were presented to both species: 1v2, 1v3, 1v5, 2v3, 2v4, and 2v5. Each was distributed 1 at a time across 2 7-location arrays. Every individual item was viewed 1 at a time and hidden, with no more than a single item in each location of an array, in contrast to a format where all items were placed together into 2 single locations. Subjects responded by selecting 1 of the 2 arrays and received the entire quantity of food items hidden within that array. Both species performed better than chance levels. The ratio of items between sets was a significant predictor of performance in the chimpanzees, but it was not significant for robins. Instead, the absolute value of the smaller quantity of items presented was the significant factor in robin responses. These results suggest a species difference for this task when considering various dimensions such as ratio or total number of items in quantity comparisons distributed across discrete 7-location arrays.

  2. Among-species differences in pollen quality and quantity limitation: implications for endemics in biodiverse hotspots.

    PubMed

    Alonso, Conchita; Navarro-Fernández, Carmen M; Arceo-Gómez, Gerardo; Meindl, George A; Parra-Tabla, Víctor; Ashman, Tia-Lynn

    2013-11-01

    Insufficient pollination is a function of quantity and quality of pollen receipt, and the relative contribution of each to pollen limitation may vary with intrinsic plant traits and extrinsic ecological properties. Community-level studies are essential to evaluate variation across species in quality limitation under common ecological conditions. This study examined whether endemic species are more limited by pollen quantity or quality than non-endemic co-flowering species in three endemic-rich plant communities located in biodiversity hotspots of different continents (Andalusia, California and Yucatan). Natural variations in pollen receipt and pollen tube formation were analysed for 20 insect-pollinated plants. Endemic and non-endemic species that co-flowered were paired in order to estimate and compare the quantity and quality components of pre-zygotic pollination success, obtained through piecewise regression analysis of the relationship between pollen grains and pollen tubes of naturally pollinated wilted flowers. Pollen tubes did not frequently exceed the number of ovules per flower. Only the combination of abundant and good quality pollen and a low number of ovules per flower conferred relief from pre-zygotic pollen limitation in the three stochastic pollination environments studied. Quality of pollen receipt was found to be as variable as quantity among study species. The relative pollination success of endemic and non-endemic species, and its quantity and quality components, was community dependent. Assessing both quality and quantity of pollen receipt is key to determining the ovule fertilization potential of both endemic and widespread plants in biodiverse hotspot regions. Large natural variation among flowers of the same species in the two components and pollen tube formation deserves further analysis in order to estimate the environmental, phenotypic and intraindividual sources of variation that may affect how plants evolve to overcome this limitation in

  3. NEW APPROACHES TO ESTIMATION OF SOLID-WASTE QUANTITY AND COMPOSITION

    EPA Science Inventory

    Efficient and statistically sound sampling protocols for estimating the quantity and composition of solid waste over a stated period of time in a given location, such as a landfill site or at a specific point in an industrial or commercial process, are essential to the design ...

  4. 21 CFR 201.62 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... this section. (c) The declaration may contain common or decimal fractions. A common fraction shall be... firmly established, general consumer usage and trade custom of employing different common fractions in the net quantity declaration of a particular commodity, they may be employed. A common fraction shall...

  5. 21 CFR 201.62 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... this section. (c) The declaration may contain common or decimal fractions. A common fraction shall be... firmly established, general consumer usage and trade custom of employing different common fractions in the net quantity declaration of a particular commodity, they may be employed. A common fraction shall...

  6. 21 CFR 701.13 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... will give such information. (d) The declaration may contain common or decimal fractions. A common... there exists a firmly established, general consumer usage and trade custom of employing different common fractions in the net quantity declaration of a particular commodity they may be employed. A common fraction...

  7. Color Coding of Circuit Quantities in Introductory Circuit Analysis Instruction

    ERIC Educational Resources Information Center

    Reisslein, Jana; Johnson, Amy M.; Reisslein, Martin

    2015-01-01

    Learning the analysis of electrical circuits represented by circuit diagrams is often challenging for novice students. An open research question in electrical circuit analysis instruction is whether color coding of the mathematical symbols (variables) that denote electrical quantities can improve circuit analysis learning. The present study…

  8. Judgement of discrete and continuous quantity in adults: number counts!

    PubMed

    Nys, Julie; Content, Alain

    2012-01-01

    Three experiments involving a Stroop-like paradigm were conducted. In Experiment 1, adults received a number comparison task in which large sets of dots, orthogonally varying along a discrete dimension (number of dots) and a continuous dimension (cumulative area), were presented. Incongruent trials were processed more slowly and with less accuracy than congruent trials, suggesting that continuous dimensions such as cumulative area are automatically processed and integrated during a discrete quantity judgement task. Experiment 2, in which adults were asked to perform area comparison on the same stimuli, revealed the reciprocal interference from number on the continuous quantity judgements. Experiment 3, in which participants received both the number and area comparison tasks, confirmed the results of Experiments 1 and 2. Contrasting with earlier statements, the results support the view that number acts as a more salient cue than continuous dimensions in adults. Furthermore, the individual predisposition to automatically access approximate number representations was found to correlate significantly with adults' exact arithmetical skills.

  9. Technologic Distractions (Part 1): Summary of Approaches to Manage Alert Quantity With Intent to Reduce Alert Fatigue and Suggestions for Alert Fatigue Metrics.

    PubMed

    Kane-Gill, Sandra L; O'Connor, Michael F; Rothschild, Jeffrey M; Selby, Nicholas M; McLean, Barbara; Bonafide, Christopher P; Cvach, Maria M; Hu, Xiao; Konkani, Avinash; Pelter, Michele M; Winters, Bradford D

    2017-09-01

    To provide ICU clinicians with evidence-based guidance on tested interventions that reduce or prevent alert fatigue within clinical decision support systems. Systematic review of PubMed, Embase, SCOPUS, and CINAHL for relevant literature from 1966 to February 2017. Focus on critically ill patients and included evaluations in other patient care settings, as well. Identified interventions designed to reduce or prevent alert fatigue within clinical decision support systems. Study selection was based on one primary key question to identify effective interventions that attempted to reduce alert fatigue and three secondary key questions that covered the negative effects of alert fatigue, potential unintended consequences of efforts to reduce alert fatigue, and ideal alert quantity. Data were abstracted by two reviewers independently using a standardized abstraction tool. Surveys, meeting abstracts, "gray" literature, studies not available in English, and studies with non-original data were excluded. For the primary key question, articles were excluded if they did not provide a comparator as key question 1 was designed as a problem, intervention, comparison, and outcome question. We anticipated that reduction in alert fatigue, including the concept of desensitization may not be directly measured and thus considered interventions that reduced alert quantity as a surrogate marker for alert fatigue. Twenty-six articles met the inclusion criteria. Approaches for managing alert fatigue in the ICU are provided as a result of reviewing tested interventions that reduced alert quantity with the anticipated effect of reducing fatigue. Suggested alert management strategies include prioritizing alerts, developing sophisticated alerts, customizing commercially available alerts, and including end user opinion in alert selection. Alert fatigue itself is studied less frequently, as an outcome, and there is a need for more precise evaluation. Standardized metrics for alert fatigue is

  10. Information quantity and quality affect the realistic accuracy of personality judgment.

    PubMed

    Letzring, Tera D; Wells, Shannon M; Funder, David C

    2006-07-01

    Triads of unacquainted college students interacted in 1 of 5 experimental conditions that manipulated information quantity (amount of information) and information quality (relevance of information to personality), and they then made judgments of each others' personalities. To determine accuracy, the authors compared the ratings of each judge to a broad-based accuracy criterion composed of personality ratings from 3 types of knowledgeable informants (the self, real-life acquaintances, and clinician-interviewers). Results supported the hypothesis that information quantity and quality would be positively related to objective knowledge about the targets and realistic accuracy. Interjudge consensus and self-other agreement followed a similar pattern. These findings are consistent with expectations based on models of the process of accurate judgment (D. C. Funder, 1995, 1999) and consensus (D. A. Kenny, 1994). Copyright 2006 APA, all rights reserved.

  11. Master standard data quantity food production code. Macro elements for synthesizing production labor time.

    PubMed

    Matthews, M E; Waldvogel, C F; Mahaffey, M J; Zemel, P C

    1978-06-01

    Preparation procedures of standardized quantity formulas were analyzed for similarities and differences in production activities, and three entrée classifications were developed, based on these activities. Two formulas from each classification were selected, preparation procedures were divided into elements of production, and the MSD Quantity Food Production Code was applied. Macro elements not included in the existing Code were simulated, coded, assigned associated Time Measurement Units, and added to the MSD Quantity Food Production Code. Repeated occurrence of similar elements within production methods indicated that macro elements could be synthesized for use within one or more entrée classifications. Basic elements were grouped, simulated, and macro elements were derived. Macro elements were applied in the simulated production of 100 portions of each entrée formula. Total production time for each formula and average production time for each entrée classification were calculated. Application of macro elements indicated that this method of predetermining production time was feasible and could be adapted by quantity foodservice managers as a decision technique used to evaluate menu mix, production personnel schedules, and allocation of equipment usage. These macro elements could serve as a basis for further development and refinement of other macro elements which could be applied to a variety of menu item formulas.

  12. [Opinion of women from a family health unit about the quantity of mothermilk produced].

    PubMed

    Borges, Ana Luiza Vilela; Philippi, Sonia Tucunduva

    2003-01-01

    This is a study aimed at knowing the opinion of women about the quantity of mothermilk produced, since insufficient milk is one of the main reasons mentioned by women from different cultures when introducing complementary feeding in children's diet before the fourth month of life. The interviews were made at the homes of 41 women from a family health unit in the Eastern area of S o Paulo City in 1998 and 1999. The majority of the mothers (82.9%) considered they were producing a sufficient quantity of mothermilk. As evaluation criteria for the produced quantity of mothermilk, they used the size of the breasts, the spontaneous dropping of milk and the mood of the child after breastfeeding. All women introduced artificial milk before the fourth month, but those who mentioned insufficient milk did it earlier (p=0.0088).

  13. Hazardous Waste Management for the Small Quantity Generator. Teacher Edition.

    ERIC Educational Resources Information Center

    Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

    This instructional package for teaching about the regulations imposed on small quantity generators by the Environmental Protection Agency (EPA) under the Resource Conservation Recovery Act is organized around ll program objectives: students will be able to (l) determine a hazardous waste from lists or by identifying characteristics; (2) identify…

  14. 21 CFR 801.62 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... paragraph (p) of this section. (c) The declaration may contain common or decimal fractions. A common... there exists a firmly established, general consumer usage and trade custom of employing different common fractions in the net quantity declaration of a particular commodity, they may be employed. A common fraction...

  15. The Effects of Meal Schedule and Quantity on Problematic Behavior.

    ERIC Educational Resources Information Center

    Wacker, David P.; And Others

    1996-01-01

    Two case examples (a toddler with severe developmental delays and a 7-year old with severe mental retardation) illustrating effects of meal schedule and food quantity on displays of problematic behavior are offered. Brief functional analyses of aberrant behavior provided useful information for interpreting distinct patterns of behavior. (DB)

  16. 16 CFR 500.6 - Net quantity of contents declaration, location.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ..., location. 500.6 Section 500.6 Commercial Practices FEDERAL TRADE COMMISSION RULES, REGULATIONS, STATEMENT... contents separately and accurately stated on the principal display panel. (b) The declaration of net quantity shall appear as a distinct item on the principal display panel, shall be separated (by at least a...

  17. Online Exhibits & Concept Maps

    NASA Astrophysics Data System (ADS)

    Douma, M.

    2009-12-01

    , teachers, artists, and web designers, a smaller scale collaborative effort can result in an effective mini-exhibit. Online concept maps can present a large quantity of information in bite-size chunks, demonstrating interrelationships between pieces of information without inundating visitors. SpicyNodes uses radial mapping technology to enable visitors to learn about a topic or search for information in intuitive and organic ways. This online concept mapping tool can be used as a portal to invite exploration into topics, or as a means of displaying hierarchies of information. With nodes that contain text, audio, video, and links, interactive online concept maps especially engage visual, kinesthetic, and nonlinear learners. SpicyNodes is also useful for scientists who wish to complement papers, chapters, and books with an online interface that is especially appealing to nonlinear learners. Essentially, SpicyNodes shifts the burden of discovery from the reader to the author. For example, the author may create a nodemap on climate change with hundreds of nodes, but as visitors drill through the nodemap for information (e.g. from climate change to atmospheric gases to carbon dioxide), they see only a few nodes at a time and are not overwhelmed.

  18. 40 CFR 723.50 - Chemical substances manufactured in quantities of 10,000 kilograms or less per year, and chemical...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... quantities of 10,000 kilograms or less per year, and chemical substances with low environmental releases and... Chemical substances manufactured in quantities of 10,000 kilograms or less per year, and chemical... in quantities of 10,000 kilograms or less per year. (ii) Chemical substances with low environmental...

  19. 21 CFR 201.51 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... (CONTINUED) DRUGS: GENERAL LABELING Labeling Requirements for Prescription Drugs and/or Insulin § 201.51 Declaration of net quantity of contents. (a) The label of a prescription or insulin-containing drug in package....). A statement of the liquid measure of the contents in the case of insulin-containing drugs shall be...

  20. 21 CFR 201.51 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... (CONTINUED) DRUGS: GENERAL LABELING Labeling Requirements for Prescription Drugs and/or Insulin § 201.51 Declaration of net quantity of contents. (a) The label of a prescription or insulin-containing drug in package....). A statement of the liquid measure of the contents in the case of insulin-containing drugs shall be...

  1. 21 CFR 201.51 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... (CONTINUED) DRUGS: GENERAL LABELING Labeling Requirements for Prescription Drugs and/or Insulin § 201.51 Declaration of net quantity of contents. (a) The label of a prescription or insulin-containing drug in package....). A statement of the liquid measure of the contents in the case of insulin-containing drugs shall be...

  2. 21 CFR 701.13 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... typography, layout, color, embossing, or molding) to other matter on the package; except that a declaration of net quantity blown, embossed, or molded on a glass or plastic surface is permissible when all... inches. Where the declaration is blown, embossed, or molded on a glass or plastic surface rather than by...

  3. 21 CFR 201.51 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... (CONTINUED) DRUGS: GENERAL LABELING Labeling Requirements for Prescription Drugs and/or Insulin § 201.51 Declaration of net quantity of contents. (a) The label of a prescription or insulin-containing drug in package....). A statement of the liquid measure of the contents in the case of insulin-containing drugs shall be...

  4. 21 CFR 201.51 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... (CONTINUED) DRUGS: GENERAL LABELING Labeling Requirements for Prescription Drugs and/or Insulin § 201.51 Declaration of net quantity of contents. (a) The label of a prescription or insulin-containing drug in package....). A statement of the liquid measure of the contents in the case of insulin-containing drugs shall be...

  5. 21 CFR 516.36 - Insufficient quantities of MUMS-designated drugs.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS NEW ANIMAL DRUGS FOR MINOR USE AND MINOR SPECIES Designation of a Minor Use or Minor Species New Animal Drug § 516.36 Insufficient quantities of... the 7-year period of exclusive marketing rights. (b) If, within the time that FDA specifies, the...

  6. 21 CFR 516.36 - Insufficient quantities of MUMS-designated drugs.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS NEW ANIMAL DRUGS FOR MINOR USE AND MINOR SPECIES Designation of a Minor Use or Minor Species New Animal Drug § 516.36 Insufficient quantities of... the 7-year period of exclusive marketing rights. (b) If, within the time that FDA specifies, the...

  7. 21 CFR 516.36 - Insufficient quantities of MUMS-designated drugs.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS NEW ANIMAL DRUGS FOR MINOR USE AND MINOR SPECIES Designation of a Minor Use or Minor Species New Animal Drug § 516.36 Insufficient quantities of... the 7-year period of exclusive marketing rights. (b) If, within the time that FDA specifies, the...

  8. 21 CFR 516.36 - Insufficient quantities of MUMS-designated drugs.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS NEW ANIMAL DRUGS FOR MINOR USE AND MINOR SPECIES Designation of a Minor Use or Minor Species New Animal Drug § 516.36 Insufficient quantities of... the 7-year period of exclusive marketing rights. (b) If, within the time that FDA specifies, the...

  9. 21 CFR 516.36 - Insufficient quantities of MUMS-designated drugs.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS NEW ANIMAL DRUGS FOR MINOR USE AND MINOR SPECIES Designation of a Minor Use or Minor Species New Animal Drug § 516.36 Insufficient quantities of... the 7-year period of exclusive marketing rights. (b) If, within the time that FDA specifies, the...

  10. Mapping among Number Words, Numerals, and Nonsymbolic Quantities in Preschoolers

    ERIC Educational Resources Information Center

    Hurst, Michelle; Anderson, Ursula; Cordes, Sara

    2017-01-01

    In mathematically literate societies, numerical information is represented in 3 distinct codes: a verbal code (i.e., number words); a digital, symbolic code (e.g., Arabic numerals); and an analogical code (i.e., quantities; Dehaene, 1992). To communicate effectively using these numerical codes, our understanding of number must involve an…

  11. 27 CFR 19.93 - Quantity determination of spirits in bond.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Miscellaneous Provisions Gauging of Spirits, Wines Or Alcoholic Flavoring Materials § 19.93 Quantity determination of spirits in bond. Where bulk spirits in bond are gauged for determination of tax, or are gauged.... In all other instances where spirits are gauged in bond, gauged for denaturation, or are gauged for...

  12. Loneliness in Early Adolescence: Friendship Quantity, Friendship Quality, and Dyadic Processes.

    PubMed

    Lodder, Gerine M A; Scholte, Ron H J; Goossens, Luc; Verhagen, Maaike

    2017-01-01

    Friendship quantity and quality are related to adolescent loneliness, but the exact link between these constructs is not well understood. The present study aimed to examine whether adolescents' perception of friendship quantity and quality, and the perceptions of their peers, were related to loneliness. We examined the relation between loneliness and the number of unilateral and reciprocal friendships and compared the views of best friendship quality. Overall, 1,172 Dutch adolescents (49.1% male, M age = 12.81, SD = .43) nominated their friends and rated their friendship quality. Friendship quantity was measured using sociometrics to distinguish reciprocated and unilateral (i.e., one-sided) friendships. The analyses indicated that loneliness was related to fewer reciprocal and unilateral-received friendships (i.e., the adolescent received a friendship nomination but did not reciprocate that nomination) and a lower quality of best friendship. Actor-partner interdependence analyses revealed that adolescents' loneliness was related to a less positive evaluation of their friendship, as reported by adolescents themselves (i.e., a significant actor effect) but not by their friends (i.e., nonsignificant partner effect). These findings (a) indicate that loneliness is negatively related to the number of friends adolescents have, as perceived by themselves and their peers and (b) suggest that, once a friendship is established, lonely adolescents may interpret the friendship quality less positively compared to their friends. Implications of these findings for our current understanding of adolescent loneliness are discussed, and suggestions for future research are outlined.

  13. The individual and combined influence of the "quality" and "quantity" of family meals on adult body mass index.

    PubMed

    Berge, Jerica M; Wickel, Katharine; Doherty, William J

    2012-12-01

    Although there is a well-established literature showing a positive association between the frequency of family meals and child and adolescent healthful dietary intake and lower body mass index (BMI), little is known about the association between family meal frequency (quantity) and adult health outcomes and whether quality (distractions) of family meals influences adult BMI. This study investigates the association between the quantity and quality of family meals and adult BMI. Data were from a nationally representative sample of 4,885 adults ages 25 to 64 years (56% female), from which an analytic sample of 1,779 parents was drawn for the current study. Multiple linear regression was used to test the relationship between family meal frequency and quality of family meals and adult BMI, controlling for sociodemographics. Interactions between family meal quantity and quality were also examined. The quantity of family meals and the quality of family meals were both independently related to adult BMI. Specifically, the frequency of family meals was associated with lower adult BMI and lower quality of family meals was associated with higher adult BMI. The interaction between quantity and quality was not statistically significant. Results suggest that both the quantity and quality of family meals matter for adult BMI, but one is not dependent on the other. Health care providers who work with families may want to consider promoting the importance of the quality and quantity of family meals to benefit the entire family.

  14. Space Mission Concept Development Using Concept Maturity Levels

    NASA Technical Reports Server (NTRS)

    Wessen, Randii R.; Borden, Chester; Ziemer, John; Kwok, Johnny

    2013-01-01

    Over the past five years, pre-project formulation experts at the Jet Propulsion Laboratory (JPL) has developed and implemented a method for measuring and communicating the maturity of space mission concepts. Mission concept development teams use this method, and associated tools, prior to concepts entering their Formulation Phases (Phase A/B). The organizing structure is Concept Maturity Level (CML), which is a classification system for characterizing the various levels of a concept's maturity. The key strength of CMLs is the ability to evolve mission concepts guided by an incremental set of assessment needs. The CML definitions have been expanded into a matrix form to identify the breadth and depth of analysis needed for a concept to reach a specific level of maturity. This matrix enables improved assessment and communication by addressing the fundamental dimensions (e.g., science objectives, mission design, technical risk, project organization, cost, export compliance, etc.) associated with mission concept evolution. JPL's collaborative engineering, dedicated concept development, and proposal teams all use these and other CML-appropriate design tools to advance their mission concept designs. This paper focuses on mission concept's early Pre-Phase A represented by CMLs 1- 4. The scope was limited due to the fact that CMLs 5 and 6 are already well defined based on the requirements documented in specific Announcement of Opportunities (AO) and Concept Study Report (CSR) guidelines, respectively, for competitive missions; and by NASA's Procedural Requirements NPR 7120.5E document for Projects in their Formulation Phase.

  15. Quantity discrimination in canids: Dogs (Canis familiaris) and wolves (Canis lupus) compared.

    PubMed

    Miletto Petrazzini, Maria Elena; Wynne, Clive D L

    2017-11-01

    Accumulating evidence indicates that animals are able to discriminate between quantities. Recent studies have shown that dogs' and coyotes' ability to discriminate between quantities of food items decreases with increasing numerical ratio. Conversely, wolves' performance is not affected by numerical ratio. Cross-species comparisons are difficult because of differences in the methodologies employed, and hence it is still unclear whether domestication altered quantitative abilities in canids. Here we used the same procedure to compare pet dogs and wolves in a spontaneous food choice task. Subjects were presented with two quantities of food items and allowed to choose only one option. Four numerical contrasts of increasing difficulty (range 1-4) were used to assess the influence of numerical ratio on the performance of the two species. Dogs' accuracy was affected by numerical ratio, while no ratio effect was observed in wolves. These results align with previous findings and reinforce the idea of different quantitative competences in dogs and wolves. Although we cannot exclude that other variables might have played a role in shaping quantitative abilities in these two species, our results might suggest that the interspecific differences here reported may have arisen as a result of domestication. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. 27 CFR 24.242 - Authority to use greater quantities of decolorizing material in juice or wine.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... quantities of decolorizing material in juice or wine. 24.242 Section 24.242 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Storage, Treatment and Finishing of Wine § 24.242 Authority to use greater quantities of decolorizing material in...

  17. Dental wear quantity and direction in Chalcolithic and Medieval populations from southwest France.

    PubMed

    Grimoud, Anne-Marie; Gibbon, Victoria E

    2017-01-01

    The aim of this study was to verify if dental wear changed due to the dietary shift between the Chalcolithic and Middle Ages from relatively hard and fibrous foods to soft cooked cereals. This was accomplished by comparing dental wear quantity and direction between people from two archaeological sites, Les Treilles during the Chalcolithic (mixed subsistence farmers) and Marsan from the Middle Ages (agriculturalists) in southwest France. The materials studied include 65 mandibles, 32 from Les Treilles and 33 from Marsan; 549 teeth were studied. The results show statistically significant difference in wear quantity and direction, the Chalcolithic population (Les Treilles) had the greatest levels of wear in a mainly oblique direction, with the anterior teeth heavily affected by wear. Comparatively, the Medieval sample (Marsan) had lesser levels of wear in a mainly horizontal direction, and the most heavily worn teeth were the molars and incisors. The quantity of wear seems to correlate well with changes in diet, the high level of wear on the anterior teeth in the Chalcolithic sample corresponds with the consumption of a mixed diet of fibrous and tough foods. At Marsan, the lower wear quantity was likely due to a diet of soft boiled cereals, requiring less mastication. However, wear direction appears dependent on several factors and may correlate with more mixed subsistence practices. This study demonstrates the need for additional research into the complex actions of mastication and its effect on dental wear, as well as standardised methodology for the examination of dental wear in archaeological samples. Copyright © 2016 Elsevier GmbH. All rights reserved.

  18. 21 CFR 701.13 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... generally parallel to the base on which the package rests as it is designed to be displayed: Provided, That... containers designed to deliver the cosmetic under pressure, the declaration shall state the net quantity of... which contains the integral components making up a complete kit, and which is designed to deliver the...

  19. 21 CFR 701.13 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... generally parallel to the base on which the package rests as it is designed to be displayed: Provided, That... containers designed to deliver the cosmetic under pressure, the declaration shall state the net quantity of... which contains the integral components making up a complete kit, and which is designed to deliver the...

  20. 21 CFR 801.62 - Declaration of net quantity of contents.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ..., embossing, or molding) to other matter on the package; except that a declaration of net quantity blown, embossed, or molded on a glass or plastic surface is permissible when all label information is so formed on.... Where the declaration is blown, embossed, or molded on a glass or plastic surface rather than by...

  1. A Study of the Quantity of Time for Teaching Reading.

    ERIC Educational Resources Information Center

    Florida Reading Association.

    A study was conducted to provide descriptive information about the quantity of classroom time used for teaching reading and the interruptive events that occur during the scheduled reading time. Data were gathered from 148 public and private school teachers representing all grade levels and a wide range of teaching experience. The subjects each…

  2. 48 CFR 852.270-2 - Bread and bakery products-quantities.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Bread and bakery products-quantities. 852.270-2 Section 852.270-2 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Texts of Provisions and Clauses 852.270-2 Bread and bakery...

  3. Birthday Cake Activity Structured Arrangement for Helping Children Determining Quantities

    ERIC Educational Resources Information Center

    Mariana, Neni

    2010-01-01

    Few researches have been concerned about relation between children's spatial thinking and number sense. Narrowing for this small research, we focused on one component of spatial thinking, that is structuring objects, and one component of number senses, that is cardinality by determining quantities. This study focused on a design research that was…

  4. RBS as a new primary direct reference method for measuring quantity of material

    NASA Astrophysics Data System (ADS)

    Jeynes, C.

    2017-09-01

    The quantity of material in thin films can be measured reliably, non-destructively, and at an absolute traceable accuracy with a combined standard uncertainty of 1% by Rutherford backscattering spectrometry (RBS). We have demonstrated a measurement protocol for the determination of quantity of material by RBS that has been accredited at this accuracy to the ISO 17025 standard by the United Kingdom Accreditation Service (UKAS). The method is entirely traceable to SI units relying on no artefacts, and thus qualifies as a primary direct reference method as defined by the ISO Guide 35:1985 (paragraph 9.4.1).

  5. Maternal Support of Children's Early Numerical Concept Learning Predicts Preschool and First-Grade Math Achievement.

    PubMed

    Casey, Beth M; Lombardi, Caitlin M; Thomson, Dana; Nguyen, Hoa Nha; Paz, Melissa; Theriault, Cote A; Dearing, Eric

    2018-01-01

    The primary goal in this study was to examine maternal support of numerical concepts at 36 months as predictors of math achievement at 4½ and 6-7 years. Observational measures of mother-child interactions (n = 140) were used to examine type of support for numerical concepts. Maternal support that involved labeling the quantities of sets of objects was predictive of later child math achievement. This association was significant for preschool (d = .45) and first-grade math (d = .49), controlling for other forms of numerical support (identifying numerals, one-to-one counting) as well as potential confounding factors. The importance of maternal support of labeling set sizes at 36 months is discussed as a precursor to children's eventual understanding of the cardinal principle. © 2016 The Authors. Child Development © 2016 Society for Research in Child Development, Inc.

  6. Radio frequency tank eigenmode sensor for propellant quantity gauging

    NASA Technical Reports Server (NTRS)

    Zimmerli, Gregory A. (Inventor)

    2013-01-01

    A method for measuring the quantity of fluid in a tank may include the steps of selecting a match between a measured set of electromagnetic eigenfrequencies and a simulated plurality of sets of electromagnetic eigenfrequencies using a matching algorithm, wherein the match is one simulated set of electromagnetic eigenfrequencies from the simulated plurality of sets of electromagnetic eigenfrequencies, and determining the fill level of the tank based upon the match.

  7. Impact of stimulus format and reward value on quantity discrimination in capuchin and squirrel monkeys.

    PubMed

    Gazes, Regina Paxton; Billas, Alison R; Schmitt, Vanessa

    2018-03-01

    Quantity discrimination abilities are seen in a diverse range of species with similarities in performance patterns, suggesting common underlying cognitive mechanisms. However, methodological factors that impact performance make it difficult to draw broad phylogenetic comparisons of numerical cognition across studies. For example, some Old World monkeys selected a higher quantity stimulus more frequently when choosing between inedible (pebbles) than edible (food) stimuli. In Experiment 1 we presented brown capuchin (Cebus [Sapajus] paella) and squirrel monkeys (Saimiri sciureus) with the same two-choice quantity discrimination task in three different stimulus conditions: edible, inedible, and edible replaced (in which choice stimuli were food items that stood in for the same quantity of food items that were given as a reward). Unlike Old World monkeys, capuchins selected the higher quantity stimulus more in the edible condition and squirrel monkeys showed generally poor performance across all stimulus types. Performance patterns suggested that differences in subjective reward value might motivate differences in choice behavior between and within species. In Experiment 2 we manipulated the subjective reinforcement value of the reward by varying reward type and delay to reinforcement and found that delay to reinforcement had no impact on choice behavior, while increasing the value of the reward significantly improved performance by both species. The results of this study indicate that species presented with identical tasks may respond differently to methodological factors such as stimulus and reward types, resulting in significant differences in choice behavior that may lead to spurious suggestions of species differences in cognitive abilities.

  8. Omega-3 long-chain polyunsaturated fatty acids support aerial insectivore performance more than food quantity.

    PubMed

    Twining, Cornelia W; Brenna, J Thomas; Lawrence, Peter; Shipley, J Ryan; Tollefson, Troy N; Winkler, David W

    2016-09-27

    Once-abundant aerial insectivores, such as the Tree Swallow (Tachycineta bicolor), have declined steadily in the past several decades, making it imperative to understand all aspects of their ecology. Aerial insectivores forage on a mixture of aquatic and terrestrial insects that differ in fatty acid composition, specifically long-chain omega-3 polyunsaturated fatty acid (LCPUFA) content. Aquatic insects contain high levels of both LCPUFA and their precursor omega-3 PUFA, alpha-linolenic acid (ALA), whereas terrestrial insects contain much lower levels of both. We manipulated both the quantity and quality of food for Tree Swallow chicks in a full factorial design. Diets were either high-LCPUFA or low in LCPUFA but high in ALA, allowing us to separate the effects of direct LCPUFA in diet from the ability of Tree Swallows to convert their precursor, ALA, into LCPUFA. We found that fatty acid composition was more important for Tree Swallow chick performance than food quantity. On high-LCPUFA diets, chicks grew faster, were in better condition, and had greater immunocompetence and lower basal metabolic rates compared with chicks on both low LCPUFA diets. Increasing the quantity of high-LCPUFA diets resulted in improvements to all metrics of performance while increasing the quantity of low-LCPUFA diets only resulted in greater immunocompetence and lower metabolic rates. Chicks preferentially retained LCPUFA in brain and muscle when both food quantity and LCPUFA were limited. Our work suggests that fatty acid composition is an important dimension of aerial insectivore nutritional ecology and reinforces the importance of high-quality aquatic habitat for these declining birds.

  9. Are Quantity Surveyors Competent to Value for Civil Engineering Works? Evaluating QSs' Competencies and Militating Factors

    ERIC Educational Resources Information Center

    Olawumi, Timothy Oluwatosin; Ayegun, Olaleke Amos

    2016-01-01

    The role of the quantity surveyor is one that is often unclear amongst the general public. This study discussed the competencies of the quantity surveyor in measuring and managing civil engineering works and also carrying out the financial management for civil engineering construction projects; also outlined the various competencies and skills…

  10. And, not or: Quality, quantity in scientific publishing

    PubMed Central

    Allesina, Stefano

    2017-01-01

    Scientists often perceive a trade-off between quantity and quality in scientific publishing: finite amounts of time and effort can be spent to produce few high-quality papers or subdivided to produce many papers of lower quality. Despite this perception, previous studies have indicated the opposite relationship, in which productivity (publishing more papers) is associated with increased paper quality (usually measured by citation accumulation). We examine this question in a novel way, comparing members of the National Academy of Sciences with themselves across years, and using a much larger dataset than previously analyzed. We find that a member’s most highly cited paper in a given year has more citations in more productive years than in in less productive years. Their lowest cited paper each year, on the other hand, has fewer citations in more productive years. To disentangle the effect of the underlying distributions of citations and productivities, we repeat the analysis for hypothetical publication records generated by scrambling each author’s citation counts among their publications. Surprisingly, these artificial histories re-create the above trends almost exactly. Put another way, the observed positive relationship between quantity and quality can be interpreted as a consequence of randomly drawing citation counts for each publication: more productive years yield higher-cited papers because they have more chances to draw a large value. This suggests that citation counts, and the rewards that have come to be associated with them, may be more stochastic than previously appreciated. PMID:28570567

  11. Sleep Quantity and Quality during Acute Concussion: A Pilot Study

    PubMed Central

    Raikes, Adam C.; Schaefer, Sydney Y.

    2016-01-01

    Study Objectives: A number of subjective and objective studies provide compelling evidence of chronic post-concussion changes in sleep, yet very little is known about the acute effects of concussion on sleep quality and quantity. Therefore, the purpose of this prospective pilot study was to use actigraphy to examine the changes in sleep quality and quantity acutely following concussion at home rather than in a hospital or sleep laboratory. Methods: Seventeen young adults (7 with acute concussion, 10 controls) were recruited for this study. All participants completed two 5-day testing sessions separated by 30 days from intake (controls) or day of injury (concussion). Participants wore actigraphs and kept a sleep journal. Sleep parameter outcomes included nighttime total sleep time (nTST), 24-h total sleep time (TST), wake after sleep onset (WASO), and sleep efficiency (SE). The coefficient of variation (CV) for each sleep parameter was computed for each session. Results: nTST and TST CV was significantly greater in the concussion group. There is the additional indication that individuals with a concussion may require and obtain more sleep shortly after injury and subsequently have a shorter duration of sleep at 1 mo post-injury. This pattern was not seen in the measures of sleep quality (WASO, SE). Conclusions: Individuals with a concussion demonstrated increased nighttime sleep duration variability. This increase persisted at 1 mo post-injury and may be associated with previously documented self-reports of poor sleep quality lasting months and years after a concussion. Additionally, this increase may predispose individuals to numerous negative health outcomes if left untreated. Citation: Raikes AC, Schaefer SY. Sleep quantity and quality during acute concussion: a pilot study. SLEEP 2016;39(12):2141–2147. PMID:27748242

  12. Plotting Rates of Photosynthesis as a Function of Light Quantity.

    ERIC Educational Resources Information Center

    Dean, Rob L.

    1996-01-01

    Discusses methods for plotting rates of photosynthesis as a function of light quantity. Presents evidence that suggests that empirically derived conversion factors, which are used to convert foot candles to photon fluence rates, should be used with extreme caution. Suggests how rate data are best plotted when any kind of light meter is not…

  13. 16 CFR 503.4 - Net quantity of contents, numerical count.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... terms of count only, or in terms of count and weight, volume, area, or dimension, the regulations are... provide a net quantity statement to specify weight, volume, area, or dimensions when such are required. For example, the synthetic sponge which is packaged, requires dimensions such as “5 in. × 3 in. × 1 in...

  14. 16 CFR 503.4 - Net quantity of contents, numerical count.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... terms of count only, or in terms of count and weight, volume, area, or dimension, the regulations are... provide a net quantity statement to specify weight, volume, area, or dimensions when such are required. For example, the synthetic sponge which is packaged, requires dimensions such as “5 in. × 3 in. × 1 in...

  15. 16 CFR 503.4 - Net quantity of contents, numerical count.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... terms of count only, or in terms of count and weight, volume, area, or dimension, the regulations are... provide a net quantity statement to specify weight, volume, area, or dimensions when such are required. For example, the synthetic sponge which is packaged, requires dimensions such as “5 in. × 3 in. × 1 in...

  16. 16 CFR 503.4 - Net quantity of contents, numerical count.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... terms of count only, or in terms of count and weight, volume, area, or dimension, the regulations are... provide a net quantity statement to specify weight, volume, area, or dimensions when such are required. For example, the synthetic sponge which is packaged, requires dimensions such as “5 in. × 3 in. × 1 in...

  17. Determination of dosimetric quantities in pediatric abdominal computed tomography scans*

    PubMed Central

    Jornada, Tiago da Silva; da Silva, Teógenes Augusto

    2014-01-01

    Objective Aiming at contributing to the knowledge on doses in computed tomography (CT), this study has the objective of determining dosimetric quantities associated with pediatric abdominal CT scans, comparing the data with diagnostic reference levels (DRL). Materials and methods The study was developed with a Toshiba Asteion single-slice CT scanner and a GE BrightSpeed multi-slice CT unit in two hospitals. Measurements were performed with a pencil-type ionization chamber and a 16 cm-diameter polymethylmethacrylate trunk phantom. Results No significant difference was observed in the values for weighted air kerma index (CW), but the differences were relevant in values for volumetric air kerma index (CVOL), air kerma-length product (PKL,CT) and effective dose. Conclusion Only the CW values were lower than the DRL, suggesting that dose optimization might not be necessary. However, PKL,CT and effective dose values stressed that there still is room for reducing pediatric radiation doses. The present study emphasizes the importance of determining all dosimetric quantities associated with CT scans. PMID:25741103

  18. Thermo-mechanical concepts applied to modeling liquid propellant rocket engine stability

    NASA Astrophysics Data System (ADS)

    Kassoy, David R.; Norris, Adam

    2016-11-01

    The response of a gas to transient, spatially distributed energy addition can be quantified mathematically using thermo-mechanical concepts available in the literature. The modeling demonstrates that the ratio of the energy addition time scale to the acoustic time scale of the affected volume, and the quantity of energy added to that volume during the former determine the whether the responses to heating can be described as occurring at nearly constant volume, fully compressible or nearly constant pressure. Each of these categories is characterized by significantly different mechanical responses. Application to idealized configurations of liquid propellant rocket engines provides an opportunity to identify physical conditions compatible with gasdynamic disturbances that are sources of engine instability. Air Force Office of Scientific Research.

  19. 10 CFR 73.72 - Requirement for advance notice of shipment of formula quantities of strategic special nuclear...

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... quantities of strategic special nuclear material, special nuclear material of moderate strategic significance, or irradiated reactor fuel. 73.72 Section 73.72 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED... shipment of formula quantities of strategic special nuclear material, special nuclear material of moderate...

  20. Inventory simulation tools: Separating nuclide contributions to radiological quantities

    NASA Astrophysics Data System (ADS)

    Gilbert, Mark R.; Fleming, Michael; Sublet, Jean-Christophe

    2017-09-01

    The activation response of a material is a primary factor considered when evaluating its suitability for a nuclear application. Various radiological quantities, such as total (becquerel) activity, decay heat, and γ dose, can be readily predicted via inventory simulations, which numerically evolve in time the composition of a material under exposure to neutron irradiation. However, the resulting data sets can be very complex, often necessarily resulting in an over-simplification of the results - most commonly by just considering total response metrics. A number of different techniques for disseminating more completely the vast amount of data output from, in particular, the FISPACT-II inventory code system, including importance diagrams, nuclide maps, and primary knock-on atom (PKA) spectra, have been developed and used in scoping studies to produce database reports for the periodic table of elements. This paper introduces the latest addition to this arsenal - standardised and automated plotting of the time evolution in a radiological quantity for a given material separated by contributions from dominant radionuclides. Examples for relevant materials under predicted fusion reactor conditions, and for bench-marking studies against decay-heat measurements, demonstrate the usefulness and power of these radionuclide-separated activation plots. Note to the reader: the pdf file has been changed on September 22, 2017.

  1. 7 CFR 929.49 - Marketable quantity, allotment percentage, and annual allotment.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AGRICULTURE CRANBERRIES GROWN IN STATES OF MASSACHUSETTS, RHODE ISLAND, CONNECTICUT, NEW JERSEY, WISCONSIN... other available information, that limiting the quantity of cranberries purchased from or handled on..., no handler shall purchase or handle on behalf of any grower cranberries not within such grower's...

  2. 7 CFR 929.49 - Marketable quantity, allotment percentage, and annual allotment.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AGRICULTURE CRANBERRIES GROWN IN STATES OF MASSACHUSETTS, RHODE ISLAND, CONNECTICUT, NEW JERSEY, WISCONSIN... other available information, that limiting the quantity of cranberries purchased from or handled on..., no handler shall purchase or handle on behalf of any grower cranberries not within such grower's...

  3. 7 CFR 929.49 - Marketable quantity, allotment percentage, and annual allotment.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AGRICULTURE CRANBERRIES GROWN IN STATES OF MASSACHUSETTS, RHODE ISLAND, CONNECTICUT, NEW JERSEY, WISCONSIN... other available information, that limiting the quantity of cranberries purchased from or handled on..., no handler shall purchase or handle on behalf of any grower cranberries not within such grower's...

  4. 7 CFR 929.49 - Marketable quantity, allotment percentage, and annual allotment.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AGRICULTURE CRANBERRIES GROWN IN STATES OF MASSACHUSETTS, RHODE ISLAND, CONNECTICUT, NEW JERSEY, WISCONSIN... other available information, that limiting the quantity of cranberries purchased from or handled on..., no handler shall purchase or handle on behalf of any grower cranberries not within such grower's...

  5. Average rainwater pH, concepts of atmospheric acidity, and buffering in open systems

    NASA Astrophysics Data System (ADS)

    Liljestrand, Howard M.

    The system of water equilibrated with a constant partial pressure of CO 2, as a reference point for pH acidity-alkalinity relationships, has nonvolatile acidity and alkalinity components as conservative quantities, but not [H +]. Simple algorithms are presented for the determination of the average pH for combinations of samples both above and below pH 5.6. Averaging the nonconservative quantity [H +] yields erroneously low mean pH values. To extend the open CO 2 system to include other volatile atmospheric acids and bases distributed among the gas, liquid and particulate matter phases, a theoretical framework for atmospheric acidity is presented. Within certain oxidation-reduction limitations, the total atmospheric acidity (but not free acidity) is a conservative quantity. The concept of atmospheric acidity is applied to air-water systems approximating aerosols, fogwater, cloudwater and rainwater. The buffer intensity in hydrometeors is described as a function of net strong acidity, partial pressures of acid and base gases and the water to air ratio. For high liquid to air volume ratios, the equilibrium partial pressures of trace acid and base gases are set by the pH or net acidity controlled by the nonvolatile acid and base concentrations. For low water to air volume ratios as well as stationary state systems such as precipitation scavenging with continuous emissions, the partial pressures of trace gases (NH 3, HCl, HNO 3, SO 2 and CH 3COOH) appear to be of greater or equal importance as carbonate species as buffers in the aqueous phase.

  6. Sleep and its association with aggression among prisoners: Quantity or quality?

    PubMed

    Barker, Lyndsie Fiona; Ireland, Jane L; Chu, Simon; Ireland, Carol A

    2016-01-01

    The current paper aims to examine the association between self-reported sleep quality and quantity and how these relate to aggression motivation and hostile cognition in a male prisoner sample. The cognitive component of sleep, namely perception, is consequently a variable of particular interest and one neglected by previous research. Two independent studies are presented. The first comprised 95 adult male prisoners who completed a sleep quality index along with measures of implicit and explicit aggression. The second study extended this to consider aggression motivation and hostile attribution biases using a sample of 141 young male adult prisoners. In study one, sleep quantity and indicators of sleep quality were found not to associate with aggression whereas the perception of poor sleep did; those perceiving poor sleep quality were more likely than those perceiving good sleep to report they had perpetrated aggression in the previous week and to report higher levels of implicit aggression. Study two found that while increased indicators of poor sleep quality were associated with lower prosocial attribution tendencies and higher levels of reactive and proactive aggression, sleep quantity was not associated. The perception of poor quality sleep was important; those perceiving poor sleep were more likely to report higher levels of reactive and proactive aggression than those reporting good sleep. Collectively the studies highlight the importance of accounting for the perception of sleep quality as an important cognitive component in understanding the association between sleep and aggression. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Innatism, Concept Formation, Concept Mastery and Formal Education

    ERIC Educational Resources Information Center

    Winch, Christopher

    2015-01-01

    This article will consider the claim that the possession of concepts is innate rather than learned. Innatism about concept learning is explained through consideration of the work of Fodor and Chomsky. First, an account of concept formation is developed. Second the argument against the claim that concepts are learned through the construction of a…

  8. Importance of interactions between food quality, quantity, and gut transit time on consumer feeding, growth, and trophic dynamics.

    PubMed

    Mitra, Aditee; Flynn, Kevin J

    2007-05-01

    Ingestion kinetics of animals are controlled by both external food availability and feedback from the quantity of material already within the gut. The latter varies with gut transit time (GTT) and digestion of the food. Ingestion, assimilation efficiency, and thus, growth dynamics are not related in a simple fashion. For the first time, the important linkage between these processes and GTT is demonstrated; this is achieved using a biomass-based, mechanistic multinutrient model fitted to experimental data for zooplankton growth dynamics when presented with food items of varying quality (stoichiometric composition) or quantity. The results show that trophic transfer dynamics will vary greatly between the extremes of feeding on low-quantity/high-quality versus high-quantity/low-quality food; these conditions are likely to occur in nature. Descriptions of consumer behavior that assume a constant relationship between the kinetics of grazing and growth irrespective of food quality and/or quantity, with little or no recognition of the combined importance of these factors on consumer behavior, may seriously misrepresent consumer activity in dynamic situations.

  9. [Response of Algae to Nitrogen and Phosphorus Concentration and Quantity of Pumping Water in Pumped Storage Reservoir].

    PubMed

    Wan, You-peng; Yin, Kui-hao; Peng, Sheng-hua

    2015-06-01

    Taking a pumped storage reservoir located in southern China as the research object, the paper established a three-dimensional hydrodynamic and eutrophication model of the reservoir employing EFDC (environmental fluid dynamics code) model, calibrated and verified the model using long-term hydraulic and water quality data. Based on the model results, the effects of nitrogen and phosphorus concentrations on the algae growth were analyzed, and the response of algae to nitrogen and phosphorus concentration and quantity of pumping water was also calculated. The results showed that the nitrogen and phosphorus concentrations had little limit on algae growth rate in the reservoir. In the nutrients reduction scenarios, reducing phosphorus would gain greater algae biomass reduction than reducing nitrogen. When reducing 60 percent of nitrogen, the algae biomass did not decrease, while 12.4 percent of algae biomass reduction could be gained with the same reduction ratio of phosphorus. When the reduction ratio went to 90 percent, the algae biomass decreased by 17.9 percent and 35.1 percent for nitrogen and phosphorus reduction, respectively. In the pumping water quantity regulation scenarios, the algae biomass decreased with the increasing pumping water quantity when the pumping water quantity was greater than 20 percent of the current value; when it was less than 20 percent, the algae biomass increased with the increasing pumping water quantity. The algae biomass decreased by 25.7 percent when the pumping water quantity was doubled, and increased by 38.8 percent when it decreased to 20 percent. The study could play an important role in supporting eutrophication controlling in water source area.

  10. 7 CFR 929.49 - Marketable quantity, allotment percentage, and annual allotment.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ...) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF... history, established pursuant to § 929.48. Such allotment percentage shall be established by the Secretary and shall equal the marketable quantity divided by the total of all growers' sales histories including...

  11. Identifying predictors for quality and quantity restorative character of wilderness: using events as an analysis unit

    Treesearch

    Chad D. Pierskalla; Jason M. Siniscalchi; William E. Hammitt; David A. Smaldone; Steven J. Storck

    2007-01-01

    The purpose of this research is to understand whether and how trail design and resource impacts influence the quality and quantity of restorative experiences. The focus of past research has been on understanding the quality-side (what happens). What is missing is a better understanding of the quantity-side of experiences (how much happens). Gibson's environmental...

  12. Natural products phytotoxicity A bioassay suitable for small quantities of slightly water-soluble compounds.

    PubMed

    Dornbos, D L; Spencer, G F

    1990-02-01

    A large variety of secondary metabolites that can inhibit germination and/or seedling growth are produced by plants in low quantities. The objective of this study was to develop a bioassay capable of reliably assessing reductions in germination percentage and seedling length of small-seeded plant species caused by exposure to minute quantities of these compounds. The germination and growth of alfalfa (Medicago saliva), annual ryegrass (Lolium multiflorum), and velvetleaf (Abutilon theophrasti) were evaluated against six known phytotoxins from five chemical classes; cinmethylin (a herbicidal cineole derivative) was selected as a comparison standard. Each phytotoxin, dissolved in a suitable organic solvent, was placed on water-agar in small tissue culture wells. After the solvent evaporated, imbibed seeds were placed on the agar; after three days, germination percentages and seedling lengths were measured. Compared to a commonly used filter paper procedure, this modified agar bioassay required smaller quantities of compound per seed for comparable bioassay results. This bioassay also readily permitted the measurement of seedling length, a more sensitive indicator of phytotoxicity than germination. Seedling length decreased sigmoidally as the toxin concentration increased logarithmically. Phytotoxicity was a function of both compound and plant species. Cinmethylin, a grass herbicide, reduced the length of annual ryegrass seedlings by 90-100%, whereas that of alfalfa and velvetleaf was inhibited slightly. The agar bioassay facilitated the rapid and reliable testing of slightly water-soluble compounds, requiring only minute quantities of each compound to give reproducible results.

  13. The perception of phonological quantity based on durational cues by native speakers, second-language users and nonspeakers of Finnish.

    PubMed

    Ylinen, Sari; Shestakova, Anna; Alku, Paavo; Huotilainen, Minna

    2005-01-01

    Some languages, such as Finnish, use speech-sound duration as the primary cue for a phonological quantity distinction. For second-language (L2) learners, quantity is often difficult to master if speech-sound duration plays a less important role in the phonology of their native language (L1). By comparing the categorization performance of native speakers of Finnish, Russian L2 users of Finnish, and non-Finnish-speaking Russians, the present study aimed to determine whether the L2 users, whose native language does not have a quantity distinction, have been able to establish categories for Finnish quantity. The results suggest that the native speakers and some of the L2 users that have been exposed to Finnish for a longer time have access to phonological quantity categories, whereas the L2 users with shorter exposure and the non-Finnish-speaking subjects do not. In addition, by comparing categorization and discrimination tasks it was found that the native speakers show a phoneme-boundary effect for quantity that is cued by duration only, whereas the non-Finnish-speaking subjects and the subjects with low proficiency in Finnish do not.

  14. A law of order estimation and leading-order terms for a family of averaged quantities on a multibaker chain system

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ishida, Hideshi, E-mail: ishida@me.es.osaka-u.ac.jp

    2014-06-15

    In this study, a family of local quantities defined on each partition and its averaging on a macroscopic small region, site, are defined on a multibaker chain system. On its averaged quantities, a law of order estimation in the bulk system is proved, making it possible to estimate the order of the quantities with respect to the representative partition scale parameter Δ. Moreover, the form of the leading-order terms of the averaged quantities is obtained, and the form enables us to have the macroscopic quantity in the continuum limit, as Δ → 0, and to confirm its partitioning independency. Thesemore » deliverables fully explain the numerical results obtained by Ishida, consistent with the irreversible thermodynamics.« less

  15. Self-Concept Is a Concept Worth Considering

    ERIC Educational Resources Information Center

    Shields, Nora

    2009-01-01

    There is a growing recognition of the importance of self-concept in the pediatric rehabilitation research literature. There also is confusion and inconsistency in the definitions of and the terminology used to describe self-concept. What is agreed is that self-concept is multidimensional, comprising a child's perception of their personal…

  16. 46 CFR 76.23-10 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Section 76.23-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-10 Quantity, pipe sizes, and discharge rates. (a) General. (1) The system shall be so designed and arranged that the overhead is effectively...

  17. 46 CFR 76.23-10 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Section 76.23-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-10 Quantity, pipe sizes, and discharge rates. (a) General. (1) The system shall be so designed and arranged that the overhead is effectively...

  18. 46 CFR 76.23-10 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Section 76.23-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-10 Quantity, pipe sizes, and discharge rates. (a) General. (1) The system shall be so designed and arranged that the overhead is effectively...

  19. 46 CFR 76.23-10 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Section 76.23-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-10 Quantity, pipe sizes, and discharge rates. (a) General. (1) The system shall be so designed and arranged that the overhead is effectively...

  20. 46 CFR 76.23-10 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Section 76.23-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS FIRE PROTECTION EQUIPMENT Manual Sprinkling System, Details § 76.23-10 Quantity, pipe sizes, and discharge rates. (a) General. (1) The system shall be so designed and arranged that the overhead is effectively...

  1. 40 CFR 355.33 - What release quantities of EHSs and CERCLA hazardous substances trigger the emergency release...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 27 2010-07-01 2010-07-01 false What release quantities of EHSs and..., EMERGENCY PLANNING, AND COMMUNITY RIGHT-TO-KNOW PROGRAMS EMERGENCY PLANNING AND NOTIFICATION Emergency Release Notification Who Must Comply § 355.33 What release quantities of EHSs and CERCLA hazardous...

  2. Effects of nonindigenous invasive species on water quality and quantity

    Treesearch

    Frank H. McCormick; Glen C. Contreras; Sherri L. Johnson

    2010-01-01

    Physical and biological disruptions of aquatic systems caused by invasive species alter water quantity and water quality. Recent evidence suggests that water is a vector for the spread of Sudden Oak Death disease and Port-Orfordcedar root disease. Since the 1990s, the public has become increasingly aware of the presence of invasive species in the Nation’s waters. Media...

  3. Simplifying Chemical Reactor Design by using Molar Quantities Instead of Fractional Conversion.

    ERIC Educational Resources Information Center

    Brown, Lee F.; Falconer, John L.

    1987-01-01

    Explains the advantages of using molar quantities in chemical reactor design. Advocates the use of differential versions of reactor mass balances rather than the integrated forms. Provides specific examples and cases to illustrate the principles. (ML)

  4. Uncertainty quantification of measured quantities for a HCCI engine: composition or temperatures

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Petitpas, Guillaume; Whitesides, Russell

    UQHCCI_1 computes the measurement uncertainties of a HCCI engine test bench using the pressure trace and the estimated uncertainties of the measured quantities as inputs, then propagating them through Bayesian inference and a mixing model.

  5. Effects of short read quality and quantity on a de novo vertebrate transcriptome assembly.

    PubMed

    Garcia, T I; Shen, Y; Catchen, J; Amores, A; Schartl, M; Postlethwait, J; Walter, R B

    2012-01-01

    For many researchers, next generation sequencing data holds the key to answering a category of questions previously unassailable. One of the important and challenging steps in achieving these goals is accurately assembling the massive quantity of short sequencing reads into full nucleic acid sequences. For research groups working with non-model or wild systems, short read assembly can pose a significant challenge due to the lack of pre-existing EST or genome reference libraries. While many publications describe the overall process of sequencing and assembly, few address the topic of how many and what types of reads are best for assembly. The goal of this project was use real world data to explore the effects of read quantity and short read quality scores on the resulting de novo assemblies. Using several samples of short reads of various sizes and qualities we produced many assemblies in an automated manner. We observe how the properties of read length, read quality, and read quantity affect the resulting assemblies and provide some general recommendations based on our real-world data set. Published by Elsevier Inc.

  6. 46 CFR 193.15-5 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... VESSELS FIRE PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 193.15-5 Quantity, pipe sizes, and discharge rates. (a) General. The amount of carbon dioxide required for each space shall be... supply of carbon dioxide need not be provided for each space protected. The total available supply shall...

  7. 46 CFR 76.15-5 - Quantity, pipe sizes, and discharge rate.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 76.15-5 Quantity, pipe sizes, and discharge rate. (a) General. The amount of carbon dioxide required for each space shall be as determined by... the purpose of determining the amount of carbon dioxide required, a cargo compartment will be...

  8. 46 CFR 95.15-5 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... VESSELS FIRE PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 95.15-5 Quantity, pipe sizes, and discharge rates. (a) General. The amount of carbon dioxide required for each space shall be... supply of carbon dioxide need not be provided for each space protected. The total available supply shall...

  9. 46 CFR 76.15-5 - Quantity, pipe sizes, and discharge rate.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 76.15-5 Quantity, pipe sizes, and discharge rate. (a) General. The amount of carbon dioxide required for each space shall be as determined by... the purpose of determining the amount of carbon dioxide required, a cargo compartment will be...

  10. 46 CFR 193.15-5 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... VESSELS FIRE PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 193.15-5 Quantity, pipe sizes, and discharge rates. (a) General. The amount of carbon dioxide required for each space shall be... supply of carbon dioxide need not be provided for each space protected. The total available supply shall...

  11. 46 CFR 193.15-5 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... VESSELS FIRE PROTECTION EQUIPMENT Carbon Dioxide and Clean Agent Extinguishing Systems, Details § 193.15-5 Quantity, pipe sizes, and discharge rates. (a) General. The amount of carbon dioxide required for each.... A separate supply of carbon dioxide need not be provided for each space protected. The total...

  12. 46 CFR 193.15-5 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... VESSELS FIRE PROTECTION EQUIPMENT Carbon Dioxide and Clean Agent Extinguishing Systems, Details § 193.15-5 Quantity, pipe sizes, and discharge rates. (a) General. The amount of carbon dioxide required for each.... A separate supply of carbon dioxide need not be provided for each space protected. The total...

  13. 46 CFR 76.15-5 - Quantity, pipe sizes, and discharge rate.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 76.15-5 Quantity, pipe sizes, and discharge rate. (a) General. The amount of carbon dioxide required for each space shall be as determined by... the purpose of determining the amount of carbon dioxide required, a cargo compartment will be...

  14. 46 CFR 95.15-5 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... VESSELS FIRE PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 95.15-5 Quantity, pipe sizes, and discharge rates. (a) General. The amount of carbon dioxide required for each space shall be... supply of carbon dioxide need not be provided for each space protected. The total available supply shall...

  15. 46 CFR 76.15-5 - Quantity, pipe sizes, and discharge rate.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 76.15-5 Quantity, pipe sizes, and discharge rate. (a) General. The amount of carbon dioxide required for each space shall be as determined by... the purpose of determining the amount of carbon dioxide required, a cargo compartment will be...

  16. 46 CFR 95.15-5 - Quantity, pipe sizes, and discharge rates.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... VESSELS FIRE PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 95.15-5 Quantity, pipe sizes, and discharge rates. (a) General. The amount of carbon dioxide required for each space shall be... supply of carbon dioxide need not be provided for each space protected. The total available supply shall...

  17. Teachers' Construction of Meanings of Signed Quantities and Integer Operation

    ERIC Educational Resources Information Center

    Kumar, Ruchi S.; Subramaniam, K.; Naik, Shweta Shripad

    2017-01-01

    Understanding signed quantities and its arithmetic is one of the challenging topics of middle school mathematics. The "specialized content knowledge" (SCK) for teaching integers includes understanding of a variety of representations that may be used while teaching. In this study, we argue that meanings of integers and integer operations…

  18. A solution procedure for mixed-integer nonlinear programming formulation of supply chain planning with quantity discounts under demand uncertainty

    NASA Astrophysics Data System (ADS)

    Yin, Sisi; Nishi, Tatsushi

    2014-11-01

    Quantity discount policy is decision-making for trade-off prices between suppliers and manufacturers while production is changeable due to demand fluctuations in a real market. In this paper, quantity discount models which consider selection of contract suppliers, production quantity and inventory simultaneously are addressed. The supply chain planning problem with quantity discounts under demand uncertainty is formulated as a mixed-integer nonlinear programming problem (MINLP) with integral terms. We apply an outer-approximation method to solve MINLP problems. In order to improve the efficiency of the proposed method, the problem is reformulated as a stochastic model replacing the integral terms by using a normalisation technique. We present numerical examples to demonstrate the efficiency of the proposed method.

  19. Age differences in attitude change: influences of cognitive resources and motivation on responses to argument quantity.

    PubMed

    Wang, Mo; Chen, Yiwei

    2006-09-01

    This study examined the influences of cognitive resources and motivation on how young and older adults process different quantities of persuasive arguments. In the first experiment session, both young and older adults rated their attitudes toward marijuana legalization and capital punishment. After a week, they read either 3 or 9 similar-quality arguments supporting marijuana legalization and capital punishment. Half of participants were assigned to the high-involvement condition (i.e., told that they were going to discuss the arguments later with the experimenter) and the other half were assigned to the low-involvement condition (i.e., given no instructions). After reading the arguments, participants rated their attitudes toward those 2 social issues again. Highly involved young adults changed their attitudes regardless of the quantity of arguments, whereas lowly involved young adults' attitude change was influenced by the argument quantity. Older adults in both high-involvement and low-involvement conditions changed their attitudes according to the argument quantity. Working memory was found to mediate the age effects on attitude change. This finding demonstrated the importance of a cognitive mechanism in accounting for age differences in attitude change.

  20. Conceptions of Parents, Conceptions of Self, and Conceptions of God.

    ERIC Educational Resources Information Center

    Buri, John R.; Mueller, Rebecca A.

    Different theorists have suggested that an individual's view of God may be related to one's view of one's father, one's mother, or one's self. A study was conducted to examine the relationship of college students' conceptions of the wrathfulness-kindliness of God to their conceptions of their father's and mother's permissiveness, authoritarianism,…

Some links on this page may take you to non-federal websites. Their policies may differ from this site.