Analysis of noise pollution in an andesite quarry with the use of simulation studies and evaluation indices.

PubMed

Kosała, Krzysztof; Stępień, Bartłomiej

2016-01-01

This paper presents the verification of two partial indices proposed for the evaluation of continuous and impulse noise pollution in quarries. These indices, together with the sound power of machines index and the noise hazard index at the workstation, are components of the global index of assessment of noise hazard in the working environment of a quarry. This paper shows the results of acoustic tests carried out in an andesite quarry. Noise generated by machines and from performed blasting works was investigated. On the basis of acoustic measurements carried out in real conditions, the sound power levels of machines and the phenomenon of explosion were determined and, based on the results, three-dimensional models of acoustic noise propagation in the quarry were developed. To assess the degree of noise pollution in the area of the quarry, the continuous and impulse noise indices were used.

Predictions of Experimentally Observed Stochastic Ground Vibrations Induced by Blasting

PubMed Central

Kostić, Srđan; Perc, Matjaž; Vasović, Nebojša; Trajković, Slobodan

2013-01-01

In the present paper, we investigate the blast induced ground motion recorded at the limestone quarry “Suva Vrela” near Kosjerić, which is located in the western part of Serbia. We examine the recorded signals by means of surrogate data methods and a determinism test, in order to determine whether the recorded ground velocity is stochastic or deterministic in nature. Longitudinal, transversal and the vertical ground motion component are analyzed at three monitoring points that are located at different distances from the blasting source. The analysis reveals that the recordings belong to a class of stationary linear stochastic processes with Gaussian inputs, which could be distorted by a monotonic, instantaneous, time-independent nonlinear function. Low determinism factors obtained with the determinism test further confirm the stochastic nature of the recordings. Guided by the outcome of time series analysis, we propose an improved prediction model for the peak particle velocity based on a neural network. We show that, while conventional predictors fail to provide acceptable prediction accuracy, the neural network model with four main blast parameters as input, namely total charge, maximum charge per delay, distance from the blasting source to the measuring point, and hole depth, delivers significantly more accurate predictions that may be applicable on site. We also perform a sensitivity analysis, which reveals that the distance from the blasting source has the strongest influence on the final value of the peak particle velocity. This is in full agreement with previous observations and theory, thus additionally validating our methodology and main conclusions. PMID:24358140

Selection of site specific vibration equation by using analytic hierarchy process in a quarry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalayci, Ulku, E-mail: ukalayci@istanbul.edu.tr; Ozer, Umit, E-mail: uozer@istanbul.edu.tr

This paper presents a new approach for the selection of the most accurate SSVA (Site Specific Vibration Attenuation) equation for blasting processes in a quarry located near settlements in Istanbul, Turkey. In this context, the SSVA equations obtained from the same study area in the literature were considered in terms of distance between the shot points and buildings and the amount of explosive charge. In this purpose, 11 different SSVA equations obtained from the study area in the past 12 years, forecasting capabilities according to designated new conditions, using 102 vibration records as test data obtained from the study areamore » was investigated. In this study, AHP (Analytic Hierarchy Process) was selected as an analysis method in order to determine the most accurate equation among 11 SSAV equations, and the parameters such as year, distance, charge, and r{sup 2} of the equations were used as criteria for AHP. Finally, the most appropriate equation was selected among the existing ones, and the process of selecting according to different target criteria was presented. Furthermore, it was noted that the forecasting results of the selected equation is more accurate than that formed using the test results. - Highlights: • The optimum Site Specific Vibration Attenuation equation for blasting in a quarry located near settlements was determined. • It is indicated that SSVA equations changing over the years don’t give always accurate estimates at changing conditions. • Selection of the blast induced SSVA equation was made using AHP. • Equation selection method was highlighted based on parameters such as charge, distance, and quarry geometry changes (year).« less

Surface wave inversion of central Texas quarry blasts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonner, J.L.; Goforth, T.T.

1993-02-01

Compressional and shear wave models of the upper crust in central Texas were obtained by inverting Rayleigh and Love waves recorded at the new W.M. Keck Foundation Seismological Observatory at Baylor University. The Keck Observatory, which became operational in April 1992, consists of a three-component, broadband Geotech seismometer located at a depth of 130 feet in a borehole 17 miles from the Baylor campus. The field station is solar powered, and the 140-dB dynamic range digital data are transmitted to the Baylor analysis lab via radio, where they are analyzed and archived. Limestone quarries located in all directions from themore » Keck Observatory detonate two to four tons of explosives per blast several times a week. Recordings of these blasts show sharp onsets of P and S waves, as well as dispersed Rayleigh and Love waves in the period band 1 to 3 seconds. Multiple filter analysis and phase matched filtering techniques were used to obtain high quality dispersion curves for the surface waves, and inversion techniques were applied to produce shear velocity models of the upper crust. A rapid increase in shear velocity at a depth of about 1.5 km is associated with the Ouachita Overthrust Belt. Portable seismic recording systems were placed at the quarries to monitor start times and initial wave forms. These data were combined with the Keck recordings to produce attenuation and compressional velocity models.« less

What is that mysterious booming sound?

USGS Publications Warehouse

Hill, David P.

2011-01-01

The residents of coastal North Carolina are occasionally treated to sequences of booming sounds of unknown origin. The sounds are often energetic enough to rattle windows and doors. A recent sequence occurred in early January 2011 during clear weather with no evidence of local thunder storms. Queries by a local reporter (Colin Hackman of the NBC affiliate WETC in Wilmington, North Carolina, personal communication 2011) seemed to eliminate common anthropogenic sources such as sonic booms or quarry blasts. So the commonly asked question, “What's making these booming sounds?” remained (and remains) unanswered.

Silicosis

MedlinePlus

... metal ores. Silica is a main part of sand, so glass workers and sand-blasters are also exposed to silica. Three types ... Glass manufacturing Mining Quarrying Road and building construction Sand blasting Stone cutting Intense exposure to silica can ...

Source discrimination between Mining blasts and Earthquakes in Tianshan orogenic belt, NW China

NASA Astrophysics Data System (ADS)

Tang, L.; Zhang, M.; Wen, L.

2017-12-01

In recent years, a large number of quarry blasts have been detonated in Tianshan Mountains of China. It is necessary to discriminate those non-earthquake records from the earthquake catalogs in order to determine the real seismicity of the region. In this study, we have investigated spectral ratios and amplitude ratios as discriminants for regional seismic-event identification using explosions and earthquakes recorded at Xinjiang Seismic Network (XJSN) of China. We used a data set that includes 1071 earthquakes and 2881 non-earthquakes as training data recorded by the XJSN between years of 2009 and 2016, with both types of events in a comparable local magnitude range (1.5 to 2.9). The non-earthquake and earthquake groups were well separated by amplitude ratios of Pg/Sg, with the separation increasing with frequency when averaged over three stations. The 8- to 15-Hz Pg/Sg ratio was proved to be the most precise and accurate discriminant, which works for more than 90% of the events. In contrast, the P spectral ratio performed considerably worse with a significant overlap (about 60% overlap) between the earthquake and explosion populations. The comparison results show amplitude ratios between compressional and shear waves discriminate better than low-frequency to high-frequency spectral ratios for individual phases. In discriminating between explosions and earthquakes, none of two discriminants were able to completely separate the two populations of events. However, a joint discrimination scheme employing simple majority voting reduces misclassifications to 10%. In the region of the study, 44% of the examined seismic events were determined to be non-earthquakes and 55% to be earthquakes. The earthquakes occurring on land are related to small faults, while the blasts are concentrated in large quarries.

[Dust concentration analysis in non-coal mining. Exposure evaluation based on measurements performed by occupational hygiene laboratories in the years 2001-2005 in Poland].

PubMed

Bujak-Pietrek, Stella; Mikołajczyk, Urszula; Szadkowska-Stańczyk, Irena

2011-01-01

Non-coal mining includes the extraction of materials for construction (stone, gravel, sand and clay), chemical industry (salt and sulfur), metallurgy (metal ores, uranium and thorium) and other mining and quarrying. Regardless of the type of mining company one of the most common health hazards in this sector is exposure to high concentrations of dust occurring during the extraction of materials. Such activities as drilling, use of blasting agents, processing of raw material, its transportation and loading are the source of large amounts of dust containing crystalline silica. Data on exposure to dust, collected by industrial hygiene laboratories on the basis of dust concentration measurements in the work environment, were obtained from the sanitary inspection service. The analysis of dust concentrations at workplaces in non-coal mining covered the years 2001-2005. The average concentration of inhalable and respirable dust and the degree of results dispersion at workposts in different branches of non-coal mining (according to NACE rev1.1) were evaluated. Also there was estimated the percentage of surveys indicating dust concentrations above hygiene standards. Almost 5000 measurements of dust concentrations were performed in the years under study. The highest concentration of inhalable dust was noted for the production of salt (5.51 mg/m3), other mining and quarrying (4.30 mg/m3) and quarrying of slate (3.77 mg/m3). For respirable dust the highest concentrations were noted in other mining and quarrying (1.10 mg/m3), quarrying of slate (1.09 mg/m3) and quarrying of stone (0.81 mg/m3). Exposure to high concentrations of dust during the extraction of non-carbon is still an important hazard to human health. Almost for all workposts under study the excess of hygiene standards were observed.

A Hybrid Ground-Motion Prediction Equation for Earthquakes in Western Alberta

NASA Astrophysics Data System (ADS)

Spriggs, N.; Yenier, E.; Law, A.; Moores, A. O.

2015-12-01

Estimation of ground-motion amplitudes that may be produced by future earthquakes constitutes the foundation of seismic hazard assessment and earthquake-resistant structural design. This is typically done by using a prediction equation that quantifies amplitudes as a function of key seismological variables such as magnitude, distance and site condition. In this study, we develop a hybrid empirical prediction equation for earthquakes in western Alberta, where evaluation of seismic hazard associated with induced seismicity is of particular interest. We use peak ground motions and response spectra from recorded seismic events to model the regional source and attenuation attributes. The available empirical data is limited in the magnitude range of engineering interest (M>4). Therefore, we combine empirical data with a simulation-based model in order to obtain seismologically informed predictions for moderate-to-large magnitude events. The methodology is two-fold. First, we investigate the shape of geometrical spreading in Alberta. We supplement the seismic data with ground motions obtained from mining/quarry blasts, in order to gain insights into the regional attenuation over a wide distance range. A comparison of ground-motion amplitudes for earthquakes and mining/quarry blasts show that both event types decay at similar rates with distance and demonstrate a significant Moho-bounce effect. In the second stage, we calibrate the source and attenuation parameters of a simulation-based prediction equation to match the available amplitude data from seismic events. We model the geometrical spreading using a trilinear function with attenuation rates obtained from the first stage, and calculate coefficients of anelastic attenuation and site amplification via regression analysis. This provides a hybrid ground-motion prediction equation that is calibrated for observed motions in western Alberta and is applicable to moderate-to-large magnitude events.

A study in cost analysis of aggregate production as depending on drilling and blasting design

NASA Astrophysics Data System (ADS)

Bilim, Niyazi; Çelik, Arif; Kekeç, Bilgehan

2017-10-01

Since aggregate production has vital importance for many engineering projects-such as construction, highway and plant-mixed concrete production-this study was undertaken to determine how the costs for such production are affected by the design of drilling and blasting processes used. Aggregates are used in the production of concrete and asphalt, which are critical resources for the construction sector. The ongoing population increase and the growth of living standards around the world drive the increasing demand for these products. As demand grows, competition has naturally arisen among producers in the industry. Competition in the market has directly affected prices, which leads to the need for new measures and cost analysis on production costs. The cost calculation is one of the most important parameters in mining activities. Aggregate production operations include drilling, blasting, secondary crushing (if necessary), loading, hauling and crushing-screening, and each of these factors affects cost. In this study, drilling and blasting design parameters (such as hole diameter, hole depth, hole distance and burden) were investigated and evaluated for their effect on the total cost of quarrying these products, based on a particular quarry selected for this research. As the result of evaluation, the parameters actually driving costs have been identified, and their effects on the cost have been determined. In addition, some suggestions are presented regarding production design which may lead to avoiding increased production costs.

Design and first tests of a Macroseismic Sensor System

NASA Astrophysics Data System (ADS)

Brueckl, Ewald; Polydor, Stefan; Ableitinger, Klaus; Rafeiner-Magor, Walter; Kristufek, Werner; Mertl, Stefan; Lenhardt, Wolfgang

2017-04-01

Seismic observatories are located in remote, low-noise areas for good reason and do not probe areas of dense and sensitive infrastructure. Complementary macroseismic data provide dense, qualitative information on ground motion in populated areas. Motivated by the QCN (Quake Catcher Network), a new low-cost sensor system (Macroseismic Sensor System = MSS) has been developed to support the evaluation of macroseismic data with quantitative information on ground movement in populated and industrial areas. Scholars, alumni and teachers from a technical high school contributed substantially to this development within the Sparkling Science project Schools & Quakes and the Citizen Science project QuakeWatch Austria. The MSS uses horizontal 4.5 Hz geophones and 16Bit AD conversion, and 100 Hz sampling, formatting to MiniSeed, and continuous data transmission via LAN or WLAN to a server are controlled by an integrated microcomputer (Raspberry Pi). Real-time generation of shake and source maps (based on proxies of the PGV in successive time windows) allows for differentiation between local seismic events (e.g., traffic noise, shock close to the sensor) and signals from earthquakes or quarry blasts. The inherent noise of the MSS is about 1% of the PGV corresponding to the lower boundary of intensity I = 2, which is below the ambient noise level at stations in highly populated or industrial areas. The MSS is already being tested at locations around a quarry with regular production blasts. An expansion to a local network in the Vienna Basin will be the next step.

Rock breaking methods to replace blasting

NASA Astrophysics Data System (ADS)

Zhou, Huisheng; Xie, Xinghua; Feng, Yuqing

2018-03-01

The method of breaking rock by blasting has a high efficiency and the cost is relatively low, but the associated vibration, flyrock, production of toxic gases since the 1970’s, the Western developed countries began to study the safety of breaking rock. This paper introduces different methods and their progress to safely break rock. Ideally, safe rock breaking would have little vibration, no fly stone, and no toxic gases, which can be widely used in municipal engineering, road excavation, high-risk mining, quarrying and complex environment.

NORSAR detection processing system

NASA Astrophysics Data System (ADS)

Loughran, L. B.

1987-05-01

This Semiannual Technical Summary describes the operation, maintenance and research activities at the Norwegian Seismic Array (NORSAR). Investigations into further potential improvements in the NORSAR array processing system have continued. A new Detection Processor (DP) program has developed and tested in an off-line mode. This program is flexible enough to conduct both NORSAR and NORESS detection processing as is done today, besides incorporating improved algorithms. A wide-band slowness estimation technique has been investigated by processing data from several events from the same location. Ten quarry blasts at a dam construction site in western Russia and sixteen Semipalatinsk nuclear explosions were selected. The major conclusion from this study is that employing a wider frequency band clearly tends to increase the stability of the slowness estimates, provided the signal-to-noise ratio is adequate over the band of interest. The stability was found, particularly for Pn, to be remarkably good for the western Norway quarry blasts when using a fixed frequency band for each phase for all ten events.

A Method of Effective Quarry Water Purifying Using Artificial Filtering Arrays

NASA Astrophysics Data System (ADS)

Tyulenev, M.; Garina, E.; Khoreshok, A.; Litvin, O.; Litvin, Y.; Maliukhina, E.

2017-01-01

The development of open pit mining in the large coal basins of Russia and other countries increases their negative impact on the environment. Along with the damage of land and air pollution by dust and combustion gases of blasting, coal pits have a significant negative impact on water resources. Polluted quarry water worsens the ecological situation on a much larger area than covered by air pollution and land damage. This significantly worsens the conditions of people living in cities and towns located near the coal pits, and complicates the subsequent restoration of the environment, irreversibly destroying the nature. Therefore, the research of quarry wastewater purifying is becoming an important mater for scholars of technical colleges and universities in the regions with developing open-pit mining. This paper describes the method of determining the basic parameters of the artificial filtering arrays formed on coal pits of Kuzbass (Western Siberia, Russia), and gives recommendations on its application.

Risk Assessment and Prediction of Flyrock Distance by Combined Multiple Regression Analysis and Monte Carlo Simulation of Quarry Blasting

NASA Astrophysics Data System (ADS)

Armaghani, Danial Jahed; Mahdiyar, Amir; Hasanipanah, Mahdi; Faradonbeh, Roohollah Shirani; Khandelwal, Manoj; Amnieh, Hassan Bakhshandeh

2016-09-01

Flyrock is considered as one of the main causes of human injury, fatalities, and structural damage among all undesirable environmental impacts of blasting. Therefore, it seems that the proper prediction/simulation of flyrock is essential, especially in order to determine blast safety area. If proper control measures are taken, then the flyrock distance can be controlled, and, in return, the risk of damage can be reduced or eliminated. The first objective of this study was to develop a predictive model for flyrock estimation based on multiple regression (MR) analyses, and after that, using the developed MR model, flyrock phenomenon was simulated by the Monte Carlo (MC) approach. In order to achieve objectives of this study, 62 blasting operations were investigated in Ulu Tiram quarry, Malaysia, and some controllable and uncontrollable factors were carefully recorded/calculated. The obtained results of MC modeling indicated that this approach is capable of simulating flyrock ranges with a good level of accuracy. The mean of simulated flyrock by MC was obtained as 236.3 m, while this value was achieved as 238.6 m for the measured one. Furthermore, a sensitivity analysis was also conducted to investigate the effects of model inputs on the output of the system. The analysis demonstrated that powder factor is the most influential parameter on fly rock among all model inputs. It is noticeable that the proposed MR and MC models should be utilized only in the studied area and the direct use of them in the other conditions is not recommended.

Blast from the past

NASA Astrophysics Data System (ADS)

Carlowicz, Michael

1996-02-01

Forget dynamite or hydraulic and mechanical drills. Industrial and federal researchers have started boring holes with rocket fuel. In a cooperative arrangement between Sandia National Laboratory, Global Environmental Solutions, and Universal Tech Corp., scientists and engineers extracted fuel from 200 rocket motors and used it as a mining explosive. In a demonstration completed last fall, researchers used 4950 kg of solid rocket propellant to move more than 22,500 metric tons of rock from the Lone Star Quarry in Prairie, Oklahoma. They found that the fuel improved blast energy and detonation velocity over traditional explosives, and it required fewer drill holes.

Fragment Size Distribution of Blasted Rock Mass

NASA Astrophysics Data System (ADS)

Jug, Jasmin; Strelec, Stjepan; Gazdek, Mario; Kavur, Boris

2017-12-01

Rock mass is a heterogeneous material, and the heterogeneity of rock causes sizes distribution of fragmented rocks in blasting. Prediction of blasted rock mass fragmentation has a significant role in the overall economics of opencast mines. Blasting as primary fragmentation can significantly decrease the cost of loading, transport, crushing and milling operations. Blast fragmentation chiefly depends on the specific blast design (geometry of blast holes drilling, the quantity and class of explosive, the blasting form, the timing and partition, etc.) and on the properties of the rock mass (including the uniaxial compressive strength, the rock mass elastic Young modulus, the rock discontinuity characteristics and the rock density). Prediction and processing of blasting results researchers can accomplish by a variety of existing software’s and models, one of them is the Kuz-Ram model, which is possibly the most widely used approach to estimating fragmentation from blasting. This paper shows the estimation of fragmentation using the "SB" program, which was created by the authors. Mentioned program includes the Kuz-Ram model. Models of fragmentation are confirmed and calibrated by comparing the estimated fragmentation with actual post-blast fragmentation from image processing techniques. In this study, the Kuz-Ram fragmentation model has been used for an open-pit limestone quarry in Dalmatia, southern Croatia. The resulting calibrated value of the rock factor enables the quality prognosis of fragmentation in further blasting works, with changed drilling geometry and blast design parameters. It also facilitates simulation in the program to optimize blasting works and get the desired fragmentations of the blasted rock mass.

The physical basis of explosion and blast injury processes.

PubMed

Proud, W G

2013-03-01

Energetic materials are widely used in civilian and military applications, such as quarrying and mining, flares, and in munitions. Recent conflicts have involved the widespread use of improvised explosive devices to attack military, civilians and infrastructure. This article gives a basic overview of explosive technology and the underlying physical processes that produce the injuries encountered. In particular aspects relevant to primary and secondary injuries are discussed.

Study of the characteristics of seismic signals generated by natural and cultural phenomena. [such as earthquakes, sonic booms, and nuclear explosions

NASA Technical Reports Server (NTRS)

Goforth, T. T.; Rasmussen, R. K.

1974-01-01

Seismic data recorded at the Tonto Forest Seismological Observatory in Arizona and the Uinta Basin Seismological Observatory in Utah were used to compare the frequency of occurrence, severity, and spectral content of ground motions resulting from earthquakes, and other natural and man-made sources with the motions generated by sonic booms. A search of data recorded at the two observatories yielded a classification of over 180,000 earthquake phase arrivals on the basis of frequency of occurrence versus maximum ground velocity. The majority of the large ground velocities were produced by seismic surface waves from moderate to large earthquakes in the western United States, and particularly along the Pacific Coast of the United States and northern Mexico. A visual analysis of raw film seismogram data over a 3-year period indicates that local and regional seismic events, including quarry blasts, are frequent in occurrence, but do not produce ground motions at the observatories comparable to either the large western United States earthquakes or to sonic booms. Seismic data from the Nevada Test Site nuclear blasts were used to derive magnitude-distance-sonic boom overpressure relations.

Development of a State-Wide 3-D Seismic Tomography Velocity Model for California

NASA Astrophysics Data System (ADS)

Thurber, C. H.; Lin, G.; Zhang, H.; Hauksson, E.; Shearer, P.; Waldhauser, F.; Hardebeck, J.; Brocher, T.

2007-12-01

We report on progress towards the development of a state-wide tomographic model of the P-wave velocity for the crust and uppermost mantle of California. The dataset combines first arrival times from earthquakes and quarry blasts recorded on regional network stations and travel times of first arrivals from explosions and airguns recorded on profile receivers and network stations. The principal active-source datasets are Geysers-San Pablo Bay, Imperial Valley, Livermore, W. Mojave, Gilroy-Coyote Lake, Shasta region, Great Valley, Morro Bay, Mono Craters-Long Valley, PACE, S. Sierras, LARSE 1 and 2, Loma Prieta, BASIX, San Francisco Peninsula and Parkfield. Our beta-version model is coarse (uniform 30 km horizontal and variable vertical gridding) but is able to image the principal features in previous separate regional models for northern and southern California, such as the high-velocity subducting Gorda Plate, upper to middle crustal velocity highs beneath the Sierra Nevada and much of the Coast Ranges, the deep low-velocity basins of the Great Valley, Ventura, and Los Angeles, and a high- velocity body in the lower crust underlying the Great Valley. The new state-wide model has improved areal coverage compared to the previous models, and extends to greater depth due to the data at large epicentral distances. We plan a series of steps to improve the model. We are enlarging and calibrating the active-source dataset as we obtain additional picks from investigators and perform quality control analyses on the existing and new picks. We will also be adding data from more quarry blasts, mainly in northern California, following an identification and calibration procedure similar to Lin et al. (2006). Composite event construction (Lin et al., in press) will be carried out for northern California for use in conventional tomography. A major contribution of the state-wide model is the identification of earthquakes yielding arrival times at both the Northern California Seismic Network and the Southern California Seismic Network. These events are critical to the determination of the seismic velocity model in central California, in the former `no-mans-land' between the Northern and Southern California networks. Ultimately, a combination of active-source datasets, composite events, original catalog picks, and differential times from both waveform cross-correlation and catalog picks will be used in a double-difference tomography inversion.

Crustal thickness variations across the Blue Ridge mountains, southern Appalachians: an alternative procedure for migrating wide-angle reflection data

Treesearch

Robert B. Hawman

2008-01-01

Migration of wide-angle reflections generated by quarry blasts suggests that crustal thickness increases from 38 km beneath the Carolina Terrane to 47–51 km along the southeastern flank of the Blue Ridge. The migration algorithm, developed for generating single-fold images from explosions and earthquakes recorded with isolated, short-aperture arrays, uses the localized...

Local earthquake tomography of Scotland

NASA Astrophysics Data System (ADS)

Luckett, Richard; Baptie, Brian

2015-03-01

Scotland is a relatively aseismic region for the use of local earthquake tomography, but 40 yr of earthquakes recorded by a good and growing network make it possible. A careful selection is made from the earthquakes located by the British Geological Survey (BGS) over the last four decades to provide a data set maximising arrival time accuracy and ray path coverage of Scotland. A large number of 1-D velocity models with different layer geometries are considered and differentiated by employing quarry blasts as ground-truth events. Then, SIMULPS14 is used to produce a robust 3-D tomographic P-wave velocity model for Scotland. In areas of high resolution the model shows good agreement with previously published interpretations of seismic refraction and reflection experiments. However, the model shows relatively little lateral variation in seismic velocity except at shallow depths, where sedimentary basins such as the Midland Valley are apparent. At greater depths, higher velocities in the northwest parts of the model suggest that the thickness of crust increases towards the south and east. This observation is also in agreement with previous studies. Quarry blasts used as ground truth events and relocated with the preferred 3-D model are shown to be markedly more accurate than when located with the existing BGS 1-D velocity model.

Geological-Technical and Geo-engineering Aspects of Dimensional Stone Underground Quarrying

NASA Astrophysics Data System (ADS)

Fornaro, Mauro; Lovera, Enrico

Underground exploitation of dimensional stones is not a novelty, being long since practised, as proved by a number of historical documents and by a certain number of ancient quarrying voids throughout the world. Anyway, so far, open cast quarrying has been the most adopted practice for the excavation of dimensional stones. One primary reason that led to this situation is of course connected to the lower production costs of an open cast exploitation compared to an underground one. This cheapness has been supported by geological and technical motives: on the one hand, the relative availability of surface deposits and, on the other, the development of technologies, which often can be used only outdoor. But, nowadays, general costs of quarrying activities should be re-evaluated because new, and often proper, restrictions have been strongly rising during recent years. As a consequence of both environmental and technical restrictions, pressure will more and more arise to reduce open cast quarrying and to promote underground exploitations. The trend is already well marked for weak rocks - for instance in the extractive basin of Carrara, where about one hundred quarries are active, 30 per cent is working underground, but also in Spain, Portugal and Greece the number of underground marble quarries is increasing - but not yet for hard rock quarrying, where only few quarries are working underground all around the world. One reason has to be found in cutting technologies traditionally used. In weak rocks, diamond wire saw and chain cutter are usable, with few adaptations, in underground spaces, while drilling and blasting, the traditional exploitation method for hard stone, is not easily usable in a confined space, where often only one free face is available. Many technicians and researchers agree that two technologies will probably open the door to underground quarrying in hard rocks: diamond wire and water jet. The first one is already available; the second should still be improved. The paper refers to some of the most important and significant examples in Italy, and underlines the possibility of extending, by underground quarrying, the exploitation of important and well-appreciated natural stones, as the quartzite-sandstone of the Tosco-Emiliano Appennini (Firenzuola Stone) and the Alpine gneisses. In order to pass from the simple experimental stage (explorative drift) to the more complex 3D design of the underground voids, detailed geo-structural reconstruction of the rock body and specific lithological in situ surveys are needed: such important aspects represent a very interesting common field between mining engineers and geologists.

Explosion Source Similarity Analysis via SVD

NASA Astrophysics Data System (ADS)

Yedlin, Matthew; Ben Horin, Yochai; Margrave, Gary

2016-04-01

An important seismological ingredient for establishing a regional seismic nuclear discriminant is the similarity analysis of a sequence of explosion sources. To investigate source similarity, we are fortunate to have access to a sequence of 1805 three-component recordings of quarry blasts, shot from March 2002 to January 2015. The centroid of these blasts has an estimated location 36.3E and 29.9N. All blasts were detonated by JPMC (Jordan Phosphate Mines Co.) All data were recorded at the Israeli NDC, HFRI, located at 30.03N and 35.03E. Data were first winnowed based on the distribution of maximum amplitudes in the neighborhood of the P-wave arrival. The winnowed data were then detrended using the algorithm of Cleveland et al (1990). The detrended data were bandpass filtered between .1 to 12 Hz using an eighth order Butterworth filter. Finally, data were sorted based on maximum trace amplitude. Two similarity analysis approaches were used. First, for each component, the entire suite of traces was decomposed into its eigenvector representation, by employing singular-valued decomposition (SVD). The data were then reconstructed using 10 percent of the singular values, with the resulting enhancement of the S-wave and surface wave arrivals. The results of this first method are then compared to the second analysis method based on the eigenface decomposition analysis of Turk and Pentland (1991). While both methods yield similar results in enhancement of data arrivals and reduction of data redundancy, more analysis is required to calibrate the recorded data to charge size, a quantity that was not available for the current study. References Cleveland, R. B., Cleveland, W. S., McRae, J. E., and Terpenning, I., Stl: A seasonal-trend decomposition procedure based on loess, Journal of Official Statistics, 6, No. 1, 3-73, 1990. Turk, M. and Pentland, A., Eigenfaces for recognition. Journal of cognitive neuroscience, 3(1), 71-86, 1991.

Terrorist Innovations in Weapons of Mass Effect: Preconditions, Causes, and Predictive Indicators

DTIC Science & Technology

2010-10-01

into the Martin Marietta Rock Quarry to steal explosives and blasting caps. This should have triggered an investigation from the FBI counterterrorism...Kifner, “In Long Fight With Israel, Hezbollah Tactics Evolved,” The New York Times, July 19, 2000. 48 Martin Dillon, The Dirty War: Covert...includes scientific discovery. Also see Martin Heidegger for a more obtuse expression of a similar idea, ( Martin Heidegger [William Lovitt, transl

Adaptive neuro-fuzzy inference systems for semi-automatic discrimination between seismic events: a study in Tehran region

NASA Astrophysics Data System (ADS)

Vasheghani Farahani, Jamileh; Zare, Mehdi; Lucas, Caro

2012-04-01

Thisarticle presents an adaptive neuro-fuzzy inference system (ANFIS) for classification of low magnitude seismic events reported in Iran by the network of Tehran Disaster Mitigation and Management Organization (TDMMO). ANFIS classifiers were used to detect seismic events using six inputs that defined the seismic events. Neuro-fuzzy coding was applied using the six extracted features as ANFIS inputs. Two types of events were defined: weak earthquakes and mining blasts. The data comprised 748 events (6289 signals) ranging from magnitude 1.1 to 4.6 recorded at 13 seismic stations between 2004 and 2009. We surveyed that there are almost 223 earthquakes with M ≤ 2.2 included in this database. Data sets from the south, east, and southeast of the city of Tehran were used to evaluate the best short period seismic discriminants, and features as inputs such as origin time of event, distance (source to station), latitude of epicenter, longitude of epicenter, magnitude, and spectral analysis (fc of the Pg wave) were used, increasing the rate of correct classification and decreasing the confusion rate between weak earthquakes and quarry blasts. The performance of the ANFIS model was evaluated for training and classification accuracy. The results confirmed that the proposed ANFIS model has good potential for determining seismic events.

Leveraging Long-term Seismic Catalogs for Automated Real-time Event Classification

NASA Astrophysics Data System (ADS)

Linville, L.; Draelos, T.; Pankow, K. L.; Young, C. J.; Alvarez, S.

2017-12-01

We investigate the use of labeled event types available through reviewed seismic catalogs to produce automated event labels on new incoming data from the crustal region spanned by the cataloged events. Using events cataloged by the University of Utah Seismograph Stations between October, 2012 and June, 2017, we calculate the spectrogram for a time window that spans the duration of each event as seen on individual stations, resulting in 110k event spectrograms (50% local earthquakes examples, 50% quarry blasts examples). Using 80% of the randomized example events ( 90k), a classifier is trained to distinguish between local earthquakes and quarry blasts. We explore variations of deep learning classifiers, incorporating elements of convolutional and recurrent neural networks. Using a single-layer Long Short Term Memory recurrent neural network, we achieve 92% accuracy on the classification task on the remaining 20K test examples. Leveraging the decisions from a group of stations that detected the same event by using the median of all classifications in the group increases the model accuracy to 96%. Additional data with equivalent processing from 500 more recently cataloged events (July, 2017), achieves the same accuracy as our test data on both single-station examples and multi-station medians, suggesting that the model can maintain accurate and stable classification rates on real-time automated events local to the University of Utah Seismograph Stations, with potentially minimal levels of re-training through time.

Moment Tensor Analysis of Shallow Sources

NASA Astrophysics Data System (ADS)

Chiang, A.; Dreger, D. S.; Ford, S. R.; Walter, W. R.; Yoo, S. H.

2015-12-01

A potential issue for moment tensor inversion of shallow seismic sources is that some moment tensor components have vanishing amplitudes at the free surface, which can result in bias in the moment tensor solution. The effects of the free-surface on the stability of the moment tensor method becomes important as we continue to investigate and improve the capabilities of regional full moment tensor inversion for source-type identification and discrimination. It is important to understand these free surface effects on discriminating shallow explosive sources for nuclear monitoring purposes. It may also be important in natural systems that have shallow seismicity such as volcanoes and geothermal systems. In this study, we apply the moment tensor based discrimination method to the HUMMING ALBATROSS quarry blasts. These shallow chemical explosions at approximately 10 m depth and recorded up to several kilometers distance represent rather severe source-station geometry in terms of vanishing traction issues. We show that the method is capable of recovering a predominantly explosive source mechanism, and the combined waveform and first motion method enables the unique discrimination of these events. Recovering the correct yield using seismic moment estimates from moment tensor inversion remains challenging but we can begin to put error bounds on our moment estimates using the NSS technique.

Simulation of the effects of nearby quarrying operations on ground-water flow at the South Well Field, Franklin County, Ohio

USGS Publications Warehouse

Nalley, Gregory M.; Haefner, Ralph J.

1999-01-01

The City of Columbus, Ohio, operates a municipal well field in southern Franklin County that is adjacent to a sand and gravel mining operation. Mining operations have the potential to alter ground-water flowpaths and change the sources of water to pumped wells. Previous ground-water-flow modeling of the area has shown that water pumped from the supply wells is derived from infiltration from nearby rivers and surrounding bedrock. Some of that water flows through existing quarries. Because water quality differs among these sources and is affected by the path along which water flows to the wells, five flow conditions were simulated to evaluate the influence of different mining scenarios on sources of water as related to the size and shape of contributing recharge areas (CRAs) to wells. The first simulation was based on a revision of an existing model by Schalk (1996). The second and third simulations included one in which a 20-foot layer of undisturbed aquifer material within the quarry above the bedrock is left intact, and another in which the 20-foot layer is removed. The fourth and fifth simulations included one in which the 20-foot layer of undisturbed aquifer material is left above the bedrock and the quarry is backfilled with fine- grained sand and silt (a byproduct of the mining operations), and another in which the 20-foot layer is removed before the quarry is backfilled with the fine-grained sand and silt. The results of the five model simulations indicate that the overall volumetric budgets among models change only slightly in response to changing conditions at the quarry. The most significant change is noted in the amount of water that the aquifers gained from constant head and river leakage. This change is due to the way the quarries were simulated and lower heads in the aquifers compared to those in simulations made with earlier models. Previously published model simulations showed that the 5-year CRAs did not extend into the area of the newest sand and gravel quarry. In this study, however, the size and shape of the CRAs differ in response to the addition of two supply wells, and the 5-year CRA for one of these wells intersects the sand and gravel quarry. Particle-tracking analysis indicates that the proportions of water from the principal water sources -- rivers, other quarries (excluding the quarry of interest), and bedrock -- stayed relatively constant among the model simulations. The number of particles that originate in the quarry of interest increased from about 1 percent of the total particles withdrawn through all wells when the 20-foot layer of undisturbed aquifer material was left intact, to 2 percent when the 20-foot layer was removed. In simulations in which the quarry of interest was filled with fine-grained sand and silt, the percentage of particles that travel through or originate in that quarry decreased to less than 1 percent of the total number of particles. Thus, the mining activities at the quarry of interest, combined with increased pumping at the two supply wells have only a small potential to change the overall water quality of water withdrawn from supply wells at the South Well Field.

Regional Discrimination of Quarry Blasts, Earthquakes and Underground Nuclear Explosions

DTIC Science & Technology

1989-04-07

MRespnse forthOTRKTEDR)I and4 GAC Sysem atASCTN) 26 Table 4 ECTN Station Locations STA N-LAT E-LONG ELEV(M) LOCATION CKO 45.9940 -77.4500 190 CHALK RIVER ...identical. Note that significant cepstral peaks occur at multiples of the 50 msec delay between shots. However, a shot pat- tern may be chosen that shows...the signals from Soviet explosions in both the East Kazakh and Caspian regions were weak and barely above noise level for most of the events. However

Blasting vibrations control: The shortcomings of traditional methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vuillaume, P.M.; Kiszlo, M.; Bernard, T.

1996-12-31

In the context of its studies for the French ministry of the environment and for the French national coal board, INERIS (the French institute for the industrial environment and hazards, formerly CERCHAR) has made a complete critical survey of the methods generally used to reduce the levels of blasting vibrations. It is generally acknowledged that the main parameter to control vibrations is the so-called instantaneous charge, or charge per delay. This should be reduced as much as possible in order to diminish vibration levels. On account of this, the use of a new generation of blasting devices, such as non-electricmore » detonators or electronic sequential timers has been developed since the seventies. INERIS has collected data from about 900 blasts in 2 quarries and 3 open pit mines. These data include input parameters such as borehole diameter, burden, spacing, charge per hole, charge per delay, total fired charge, etc ... They also include output measurements, such as vibration peak particle velocities, and main frequencies. These data have been analyzed with the help of multi variable statistical tools. Blasting tests were undertaken to evaluate new methods of vibrations control, such as the superposition of vibration signals. These methods appear to be accurate in many critical cases, but certainly would be highly improved with a better accuracy of firing delays. The development of electronic detonators seems to be the way of the future for a better blasting control.« less

Archaeometric characterization and provenance determination of sculptures and architectural elements from Gerasa, Jordan

NASA Astrophysics Data System (ADS)

Al-Bashaireh, Khaled

2018-02-01

This study aims at the identification of the provenance of white marble sculptures and architectural elements uncovered from the archaeological site of Gerasa and neighboring areas, north Jordan. Most of the marbles are probably of the Roman or Byzantine periods. Optical microscopy, X-ray diffraction, and mass spectrometry were used to investigate petrographic, mineralogical and isotopic characteristics of the samples, respectively. Analytical results were compared with the main reference databases of known Mediterranean marble quarries exploited in antiquity. The collected data show that the most likely main sources of the sculptures were the Greek marble quarries of Paros-2 (Lakkoi), Penteli (Mount Pentelikon, Attica), and Thasos-3 (Thasos Island, Cape Vathy, Aliki); the Asia Minor marble quarries of Proconessus-1 (Marmara) and Aphrodisias (Aphrodisias); and the Italian quarry of Carrara (Apuan Alps). Similarly, the Asia Minor quarries of the fine-grained Docimium (Afyon) and the coarse-grained Proconessus-1 (Marmara) and Thasos-3 are the most likely sources of the architectural elements. The results agree with published data on the wide use of these marbles for sculpture and architectural elements.

Norwegian millstone quarry landscapes

NASA Astrophysics Data System (ADS)

Heldal, Tom; Meyer, Gurli; Grenne, Tor

2013-04-01

Rotary querns and millstones were used in Norway since just after the Roman Period until the last millstone was made in the 1930s. Throughout all this time millstone mining was fundamental for daily life: millstones were needed to grind grain, our most important food source. We can find millstone quarries in many places in the country from coast to mountain. Some of them cover many square kilometers and count hundreds of quarries as physical testimonies of a long and great production history. Other quarries are small and hardly visible. Some of this history is known through written and oral tradition, but most of it is hidden and must be reconstructed from the traces we can find in the landscape today. The Millstone project has put these quarry landscapes on the map, and conducted a range of case studies, including characterization of archaeological features connected to the quarrying, interpretation of quarrying techniques and evolution of such and establishing distribution and trade patterns by the aid of geological provenance. The project also turned out to be a successful cooperation between different disciplines, in particular geology and archaeology.

Infrasonic and seismic signals from earthquakes and explosions observed with Plostina seismo-acoustic array

NASA Astrophysics Data System (ADS)

Ghica, D.; Ionescu, C.

2012-04-01

Plostina seismo-acoustic array has been recently deployed by the National Institute for Earth Physics in the central part of Romania, near the Vrancea epicentral area. The array has a 2.5 km aperture and consists of 7 seismic sites (PLOR) and 7 collocated infrasound instruments (IPLOR). The array is being used to assess the importance of collocated seismic and acoustic sensors for the purposes of (1) seismic monitoring of the local and regional events, and (2) acoustic measurement, consisting of detection of the infrasound events (explosions, mine and quarry blasts, earthquakes, aircraft etc.). This paper focuses on characterization of infrasonic and seismic signals from the earthquakes and explosions (accidental and mining type). Two Vrancea earthquakes with magnitude above 5.0 were selected to this study: one occurred on 1st of May 2011 (MD = 5.3, h = 146 km), and the other one, on 4th October 2011 (MD = 5.2, h = 142 km). The infrasonic signals from the earthquakes have the appearance of the vertical component of seismic signals. Because the mechanism of the infrasonic wave formation is the coupling of seismic waves with the atmosphere, trace velocity values for such signals are compatible with the characteristics of the various seismic phases observed with PLOR array. The study evaluates and characterizes, as well, infrasound and seismic data recorded from the explosion caused by the military accident produced at Evangelos Florakis Naval Base, in Cyprus, on 11th July 2011. Additionally, seismo-acoustic signals presumed to be related to strong mine and quarry blasts were investigated. Ground truth of mine observations provides validation of this interpretation. The combined seismo-acoustic analysis uses two types of detectors for signal identification: one is the automatic detector DFX-PMCC, applied for infrasound detection and characterization, while the other one, which is used for seismic data, is based on array processing techniques (beamforming and frequency-wave number analysis). Spectrograms of the recorded infrasonic and seismic data were examined, showing that an earthquake produces acoustic signals with a high energy in the 1 to 5 Hz frequency range, while, for the explosion, this range lays below 0.6 Hz. Using the combined analysis of the seismic and acoustic data, Plostina array can greatly enhance the event detection and localization in the region. The analysis can be, as well, particularly important in identifying sources of industrial explosion, and therefore, in monitoring of the hazard created both by earthquakes and anthropogenic sources of pollution (chemical factories, nuclear and power plants, refineries, mines).

Moment tensor analysis of very shallow sources

DOE PAGES

Chiang, Andrea; Dreger, Douglas S.; Ford, Sean R.; ...

2016-10-11

An issue for moment tensor (MT) inversion of shallow seismic sources is that some components of the Green’s functions have vanishing amplitudes at the free surface, which can result in bias in the MT solution. The effects of the free surface on the stability of the MT method become important as we continue to investigate and improve the capabilities of regional full MT inversion for source–type identification and discrimination. It is important to understand free–surface effects on discriminating shallow explosive sources for nuclear monitoring purposes. It may also be important in natural systems that have very shallow seismicity, such asmore » volcanic and geothermal systems. We examine the effects of the free surface on the MT via synthetic testing and apply the MT–based discrimination method to three quarry blasts from the HUMMING ALBATROSS experiment. These shallow chemical explosions at ~10 m depth and recorded up to several kilometers distance represent rather severe source–station geometry in terms of free–surface effects. We show that the method is capable of recovering a predominantly explosive source mechanism, and the combined waveform and first–motion method enables the unique discrimination of these events. Furthermore, recovering the design yield using seismic moment estimates from MT inversion remains challenging, but we can begin to put error bounds on our moment estimates using the network sensitivity solution technique.« less

Real-time envelope cross-correlation detector: application to induced seismicity in the Insheim and Landau deep geothermal reservoirs

NASA Astrophysics Data System (ADS)

Vasterling, Margarete; Wegler, Ulrich; Becker, Jan; Brüstle, Andrea; Bischoff, Monika

2017-01-01

We develop and test a real-time envelope cross-correlation detector for use in seismic response plans to mitigate hazard of induced seismicity. The incoming seismological data are cross-correlated in real-time with a set of previously recorded master events. For robustness against small changes in the earthquake source locations or in the focal mechanisms we cross-correlate the envelopes of the seismograms rather than the seismograms themselves. Two sequenced detection conditions are implemented: After passing a single trace cross-correlation condition, a network cross-correlation is calculated taking amplitude ratios between stations into account. Besides detecting the earthquake and assigning it to the respective reservoir, real-time magnitudes are important for seismic response plans. We estimate the magnitudes of induced microseismicity using the relative amplitudes between master event and detected event. The real-time detector is implemented as a SeisComP3 module. We carry out offline and online performance tests using seismic monitoring data of the Insheim and Landau geothermal power plants (Upper Rhine Graben, Germany), also including blasts from a nearby quarry. The comparison of the automatic real-time catalogue with a manually processed catalogue shows, that with the implemented parameters events are always correctly assigned to the respective reservoir (4 km distance between reservoirs) or the quarry (8 km and 10 km distance, respectively, from the reservoirs). The real-time catalogue achieves a magnitude of completeness around 0.0. Four per cent of the events assigned to the Insheim reservoir and zero per cent of the Landau events are misdetections. All wrong detections are local tectonic events, whereas none are caused by seismic noise.

Using the ENTLN lightning catalog to identify thunder signals in the USArray Transportable Array

NASA Astrophysics Data System (ADS)

Tytell, J. E.; Reyes, J. C.; Vernon, F.; Sloop, C.; Heckman, S.

2013-12-01

Severe weather events can pose a challenge for seismic analysts who regularly see non-seismic signals recorded at the stations. Sometimes, the noise from thunder can be confused with signals from seismic events such as quarry blasts or earthquakes depending on where and when the noise is observed. Automatic analysis of data is also severely affected by big amplitude arrivals that we could safely ignore. A comprehensive lightning catalog for the continental US in conjunction with a travel time model for thunder arrivals can help analysts identify some of these unknown sources. Researchers from Earthscope's USArray Transportable Array (TA) have partnered with the Earth Networks Total Lightning Network (ENTLN) in an effort to create such a catalog. Predicted thunder arrivals from some powerful meteorological systems affecting the main TA footprint will undergo extensive evaluation. We will examine the veracity of the predicted arrivals at different distances and azimuths and the time accuracy of the model. A combination of barometric pressure and seismic signals will be use to verify these arrivals.

Source apportionment of settleable particles in an impacted urban and industrialized region in Brazil.

PubMed

Santos, Jane Meri; Reis, Neyval Costa; Galvão, Elson Silva; Silveira, Alexsander; Goulart, Elisa Valentim; Lima, Ana Teresa

2017-09-01

Settleable particulate matter (SPM), especially coarser particles with diameters greater than 10 μm, has been found culprit of high deposition rates in cities affected by hinterland industrial activities. This is the case of Metropolitan Region of Vitoria (MRV), Espirito Santo, Brazil where industrial facilities are located within the urban sprawl and building constructions are intense. Frequent population complaints to the environmental protection agency (IEMA) throughout the years have triggered monitoring campaigns to determine SPM deposition rates and source apportionment. Eight different locations were monitored throughout the MRV, and SPM was quantified and chemically characterized. Sources profiles were defined either by using US EPA SPECIATE data or by experimental analysis. Atmospheric fallout in the MRV ranged between 2 and 20g/(m 2 30-day), with only one monitoring station ranging from 6-10 g/(m 2 30-day). EC, OC, Fe, Al, and Si were found the main constituents of dry deposition in the region. Source apportionment by the chemical mass balance (CMB) model determined that steel and iron ore pelletizing industries were the main contributor to one of the eight locations whereas resuspension, civil construction, and vehicular sources were also very important contributors to the other stations. Quarries and soil were also considered expressive SPM sources, but at the city periphery. CMB model could differentiate contributions from six industrial source groups: thermoelectric; iron ore, pellet, and pellet furnaces; coal coke and coke oven; sintering, blast furnace, and basic oxygen furnace; and soil, resuspension, and vehicles. However, the CMB model was unable to differentiate between iron ore and pellet stockpiles which are present in both steel and iron ore pelletizing industries. Further characterization of source and SPM might be necessary to aid local authorities in decision-making regarding these two industrial sources.

DOSAGE DES ELEMENTS EN TRACE DES CALCAIRES AU SERVICE DE L'ARCHEOLOGIE

DOE Office of Scientific and Technical Information (OSTI.GOV)

BLANC,A.; HOLMES,L.; HARBOTTLE,G.

1998-05-01

Numerous quarries in the Lutetian limestone formations of the Paris Basin provided stone for the building and the decoration of monuments from antiquity to the present. To determine the origin of stone used for masonry and sculptures in these monuments, a team of geologists and archaeologists has investigated 300 quarries and collected 2,300 samples. Petrographic and paleontologic examination of thin sections allows geologists to distinguish Lutetian limestones from Jurassic and Cretaceous limestones. Geologists also seek to formulate hypotheses regarding the origin of Lutetian limestones used for building and sculpture in the Paris region. In the search for the sources ofmore » building and sculptural stone, the analytical methods of geologists are limited because often several quarries produce the same lithofacies. A new tool is now available, however, to attack questions of provenance raised by art historians. Because limestones from different sources have distinctive patterns of trace-element concentrations, compositional analysis by neutron activation allows them to compare building or sculptural stone from one monument with stone from quarries or other monuments. This analytical method subjects a powdered limestone sample to standard neutron activation analysis procedures at Brookhaven National Laboratory. With the help of computer programs, the compositional fingerprints of Lutetian limestones can be determined and stored in a database. The limestone database contains data for approximately 2,100 samples from monuments, sculptures and quarries. It is particularly rich in samples from the Paris Basin.« less

Interpolity exchange of basalt tools facilitated via elite control in Hawaiian archaic states

PubMed Central

Kirch, Patrick V.; Mills, Peter R.; Lundblad, Steven P.; Sinton, John; Kahn, Jennifer G.

2012-01-01

Ethnohistoric accounts of late precontact Hawaiian archaic states emphasize the independence of chiefly controlled territories (ahupua‘a) based on an agricultural, staple economy. However, elite control of unevenly distributed resources, such as high-quality volcanic rock for adze production, may have provided an alternative source of economic power. To test this hypothesis we used nondestructive energy-dispersive X-ray fluorescence (ED-XRF) analysis of 328 lithic artifacts from 36 archaeological features in the Kahikinui district, Maui Island, to geochemically characterize the source groups. This process was followed by a limited sampling using destructive wavelength-dispersive X-ray fluorescence (WD-XRF) analysis to more precisely characterize certain nonlocal source groups. Seventeen geochemical groups were defined, eight of which represent extra-Maui Island sources. Although the majority of stone tools were derived from Maui Island sources (71%), a significant quantity (27%) of tools derived from extraisland sources, including the large Mauna Kea quarry on Hawai‘i Island as well as quarries on O‘ahu, Moloka‘i, and Lāna‘i islands. Importantly, tools quarried from extralocal sources are found in the highest frequency in elite residential features and in ritual contexts. These results suggest a significant role for a wealth economy based on the control and distribution of nonagricultural goods and resources during the rise of the Hawaiian archaic states. PMID:22203984

Analysis of Signals from an Unique Ground-Truth Infrasound Source Observed at IMS Station IS26 in Southern Germany

NASA Astrophysics Data System (ADS)

Koch, Karl

2010-05-01

Quantitative modeling of infrasound signals and development and verification of the corresponding atmospheric propagation models requires the use of well-calibrated sources. Numerous sources have been detected by the currently installed network of about 40 of the final 60 IMS infrasound stations. Besides non-nuclear explosions such as mining and quarry blasts and atmospheric phenomena like auroras, these sources include meteorites, volcanic eruptions and supersonic aircraft including re-entering spacecraft and rocket launches. All these sources of infrasound have one feature in common, in that their source parameters are not precisely known and the quantitative interpretation of the corresponding signals is therefore somewhat ambiguous. A source considered well-calibrated has been identified producing repeated infrasound signals at the IMS infrasound station IS26 in the Bavarian forest. The source results from propulsion tests of the ARIANE-5 rocket's main engine at a testing facility near Heilbronn, southern Germany. The test facility is at a range of 320 km and a backazimuth of ~280° from IS26. Ground-truth information was obtained for nearly 100 tests conducted in a 5-year period. Review of the available data for IS26 revealed that at least 28 of these tests show signals above the background noise level. These signals are verified based on the consistency of various signal parameters, e.g., arrival times, durations, and estimates of propagation characteristics (backazimuth, apparent velocity). Signal levels observed are a factor of 2-8 above the noise and reach values of up to 250 mPa for peak amplitudes, and a factor of 2-3 less for RMS measurements. Furthermore, only tests conducted during the months from October to April produce observable signals, indicating a significant change in infrasound propagation conditions between summer and winter months.

Seismic scattering attribute for sedimentary classification of nearshore marine quarries for a major beach nourishment project: Case study of Adriatic coastline, Regione Abruzzo (Italy)

NASA Astrophysics Data System (ADS)

Orlando, Luciana; Contini, Paolo; De Girolamo, Paolo

2017-06-01

Of fundamental importance for any major beach nourishment project using marine quarries is a correct sedimentary classification. The main purpose of such a classification is to identify sand with the appropriate features for beach nourishment. This task is more onerous when quarry sediments are heterogeneous and mixed with silt. This is typical of nearshore marine quarries. The presence of excess silt compromises the use of marine quarries because of the water turbidity that may be induced in the nourished beaches, especially when the beaches are protected by defense structures. Here we discuss the use of scattering amplitude of seismic data, acquired with a pinger source (2-10 kHz), to detect and classify the unconsolidated sediment of a marine quarry. A robust correlation was found between this seismic attribute and the silt content in the sediment. The scattering amplitude was numerically calculated from the seismic data and used to map slices of silt content at different depths. The results have been validated with sedimentary analysis of vibra- and rotary cores, and by the dredged material used for the beach nourishment. The marine quarry produced about 1.200.000 m3 of sand used to nourish eight different beach sites along the Adriatic coasts of the Regione Abruzzo (Italy). The large-scale sedimentary assessment of the area was based on seismic boomer data and the evaluation of the volume of dredged sediments on multibeam data surveyed before and after the exploitation of the quarry. The study shows that this approach is effective in sites with high lateral and vertical variations in the percentage of sand in the sediments.

A methodological framework to assess the socio-economic impact of underground quarries: A case study from Belgian Limburg.

PubMed

Sergeant, A; Poesen, J; Duchateau, P; Vranken, L

2016-01-15

This study developed a methodology to assess the socio-economic impact of the presence and collapse of underground limestone quarries. For this we rely on case study evidence from Riemst, a village located in Eastern Belgium and use both secondary and primary data sources. A sinkhole inventory as well as data about the prevention costs provided by the municipality was used. To estimate the recreational values of the quarries, visitor data was obtained from the tourist office of Riemst. Next, two surveys were conducted among inhabitants and four real estate agents and one notary. The direct and indirect damages were assessed using respectively the repair cost and production and real estate value losses. The total yearly direct and indirect damage equals €415000 (±€85000) and more than half of it can be attributed to the depreciation of real estate (€230000). The quarries have recreational, cultural-historical and ecological values and thus generate societal benefits. The yearly recreational value was at least €613000 in 2012 values. The ecological and cultural-historical values augment to €180000 per year (in 2012 values). Further, our study indicates that the gains from filling up the quarries below the houses located above an underground limestone quarry outweigh the costs in the case study area. The net gain from filling up the underground quarry ranges €38700 to €101700 per house. This is only the lower bound of the net gain from filling up these underground quarries since preventive filling makes future collapses less likely so that future direct repair costs will be most likely smaller. Copyright © 2015 Elsevier B.V. All rights reserved.

30 CFR 57.6404 - Separation of blasting circuits from power source.

Code of Federal Regulations, 2010 CFR

2010-07-01

... source. 57.6404 Section 57.6404 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... circuits from power source. (a) Switches used to connect the power source to a blasting circuit shall be locked in the open position except when closed to fire the blast. (b) Lead wires shall not be connected...

Behavior and Release of Nitrogen at Mines and Quarries in Nordic Conditions

NASA Astrophysics Data System (ADS)

Karlsson, Teemu; Neitola, Raisa; Jermakka, Johannes; Merta, Elina; Mroueh, Ulla-Maija

2015-04-01

The increased extraction of mineral resources and mining activities creates added pressure on the environmental issues and a proper water management in mining areas in Finland. Among others, nitrogen compounds released from explosives or from mining processes can have a detrimental effect on the environment. Thus, this project aimed at comprehensive understanding on the nitrogen issue in the extractive industry. The project collected essential data on nitrogen compounds present in the environments of mines and quarries, and generated better understanding of the discharge and behaviour of nitrogen compounds in mining areas. The sources and balances of explosives-originated nitrogen compounds at mines and quarries of different sizes were investigated and compared. Additionally, the focus was in 'nitrogen smudging' problem of waste rocks and the intensity, as well as evolution and chemical characteristics of their nitrogen contamination. According to the results, the total load of potential nitrogen to the environment depends on the scale and type of the activity as well as the type of explosives used. The main emission sources of nitrogen are process and dewatering waters. A lysimeter study showed that the explosives originated nitrogen content of left over stones from natural stone quarrying is relatively low and ca. half of the nitrogen is leached within the first weeks after detonation. The "nitrogen smudging" of natural stone quarrying left over stones is relatively low to begin with and enhanced by the rapid flushing by rainwater, thus the residues of explosives should not be considered to prevent the utilization of otherwise mineralogically inert waste rocks of good technical quality. The overall nitrogen management should take into account the background concentrations and sensitivity of the local ecosystem. The research project "Solution for Control of Nitrogen Discharges at Mines and Quarries, (MINIMAN)" was realized during years 2012-2014 as a cooperative project with GTK, VTT and TTY together with several industrial and international partners and financed by Tekes Green Mining Programme.

Application of deterministic deconvolution of ground-penetrating radar data in a study of carbonate strata

USGS Publications Warehouse

Xia, J.; Franseen, E.K.; Miller, R.D.; Weis, T.V.

2004-01-01

We successfully applied deterministic deconvolution to real ground-penetrating radar (GPR) data by using the source wavelet that was generated in and transmitted through air as the operator. The GPR data were collected with 400-MHz antennas on a bench adjacent to a cleanly exposed quarry face. The quarry site is characterized by horizontally bedded carbonate strata with shale partings. In order to provide groundtruth for this deconvolution approach, 23 conductive rods were drilled into the quarry face at key locations. The steel rods provided critical information for: (1) correlation between reflections on GPR data and geologic features exposed in the quarry face, (2) GPR resolution limits, (3) accuracy of velocities calculated from common midpoint data and (4) identifying any multiples. Comparing the results of deconvolved data with non-deconvolved data demonstrates the effectiveness of deterministic deconvolution in low dielectric-loss media for increased accuracy of velocity models (improved at least 10-15% in our study after deterministic deconvolution), increased vertical and horizontal resolution of specific geologic features and more accurate representation of geologic features as confirmed from detailed study of the adjacent quarry wall. ?? 2004 Elsevier B.V. All rights reserved.

Post-blasting seismicity in Rudna copper mine, Poland - source parameters analysis.

NASA Astrophysics Data System (ADS)

Caputa, Alicja; Rudziński, Łukasz; Talaga, Adam

2017-04-01

The really important hazard in Polish copper mines is high seismicity and corresponding rockbursts. Many methods are used to reduce the seismic hazard. Among others the most effective is preventing blasting in potentially hazardous mining panels. The method is expected to provoke small moderate tremors (up to M2.0) and reduce in this way a stress accumulation in the rockmass. This work presents an analysis, which deals with post-blasting events in Rudna copper mine, Poland. Using the Full Moment Tensor (MT) inversion and seismic spectra analysis, we try to find some characteristic features of post blasting seismic sources. Source parameters estimated for post-blasting events are compared with the parameters of not-provoked mining events that occurred in the vicinity of the provoked sources. Our studies show that focal mechanisms of events which occurred after blasts have similar MT decompositions, namely are characterized by a quite strong isotropic component as compared with the isotropic component of not-provoked events. Also source parameters obtained from spectral analysis show that provoked seismicity has a specific source physics. Among others, it is visible from S to P wave energy ratio, which is higher for not-provoked events. The comparison of all our results reveals a three possible groups of sources: a) occurred just after blasts, b) occurred from 5min to 24h after blasts and c) not-provoked seismicity (more than 24h after blasting). Acknowledgements: This work was supported within statutory activities No3841/E-41/S/2016 of Ministry of Science and Higher Education of Poland.

Modelling the Source of Blasting for the Numerical Simulation of Blast-Induced Ground Vibrations: A Review

NASA Astrophysics Data System (ADS)

Ainalis, Daniel; Kaufmann, Olivier; Tshibangu, Jean-Pierre; Verlinden, Olivier; Kouroussis, Georges

2017-01-01

The mining and construction industries have long been faced with considerable attention and criticism in regard to the effects of blasting. The generation of ground vibrations is one of the most significant factors associated with blasting and is becoming increasingly important as mining sites are now regularly located near urban areas. This is of concern to not only the operators of the mine but also residents. Mining sites are subjected to an inevitable compromise: a production blast is designed to fragment the utmost amount of rock possible; however, any increase in the blast can generate ground vibrations which can propagate great distances and cause structural damage or discomfort to residents in surrounding urban areas. To accurately predict the propagation of ground vibrations near these sensitive areas, the blasting process and surrounding environment must be characterised and understood. As an initial step, an accurate model of the source of blast-induced vibrations is required. This paper presents a comprehensive review of the approaches to model the blasting source in order to critically evaluate developments in the field. An overview of the blasting process and description of the various factors which influence the blast performance and subsequent ground vibrations are also presented. Several approaches to analytically model explosives are discussed. Ground vibration prediction methods focused on seed waveform and charge weight scaling techniques are presented. Finally, numerical simulations of the blasting source are discussed, including methods to estimate blasthole wall pressure time-history, and hydrodynamic codes.

Lithospheric studies along seismic profile KOKKY, between Gulf of Bothnia and Gulf of Finland, Baltic Shield

NASA Astrophysics Data System (ADS)

Tiira, Timo; Skrzynik, Tymon; Janik, Tomasz; Komminaho, Kari; Väkevä, Sakari; Korja, Annakaisa

2017-04-01

Controlled source seismology is one of the main tools used in Earth imaging, especially when aiming towards the middle and lower crust structures, Moho shape and upper mantle. Data for such studies are acquired during wide-angle reflection and refraction (WARR) profiles, which are hundreds of kilometers long and require strong explosive sources like e.g. TNT. Given the cost of such experiments, difficult logistics, and the strict regulation on experiments involving explosives in the ground, an attempt was made to register quarry blasts along the set profile. Quarries consume tons of explosive material per week and their utility in crustal studies was already tested during HUKKA experiment in 2007. Profile KOKKY begins on the coast of Bothnian Bay and runs south-east towards Sankt Petersburg in Russia. It crosses three main geological units of southern Finland, Pohjanmaa area, Central Finland Granitoid Complex, and Saimaa area, all represented by Late Proterozoic rocks. Two summer acquisition campaigns resulted in nearly 500 km long profile, crossing southern Finland. Numerous explosions from quarries were recorded, resulting in 63 usable seismic sections. Average distance between shots and the profile was 14 km. The velocity model has high P wave velocities across the entire profile. Upper crust, reaching depths of 22 km, is characterized by velocities from 5.9-6.2 km/s near surface down to 6.25-6.4 km/s. Middle crust is thinning from 30 km at NW, down to 14 km in the central part of the profile, thickening again to 20 km at SE, and has uniformed velocities 6.6-6.8 km/s. High, homogeneous velocities in lower crust, up to 7.4 km/s. Layer is thickening from 4 km in SE part of the profile, reaching 18 km in its central part corresponding to CFGC, and then thinning again to about 12 km in NW part. Moho depth varies from 54 km near the Gulf of Bothnia to 63 km in the middle of the profile, and up to 43 km in Saimaa area. Velocities below the crust are 8.2-8.25 km/s. Good quality of the data allowed to compute S velocity model and Vp/Vs ratio. This profile crosses two pre-existing WARR profiles, SVEKA and BALTIC. New model supports previous interpretations. Velocities, depth to the Moho, and other major boundaries are similar in profile crossing points. However, unlike in perpendicular profiles, no elongated and thin low velocity zones were distinguished along the entire profile. This study was a good lesson for future cost effective DSS profiles and points out key issues.

Aggregate sources for construction and maintenance in northern Arizona.

DOT National Transportation Integrated Search

2014-04-01

Constructing and maintaining Arizonas highway system requires a dependable, abundant supply of mineral : aggregates, borrow, quarried rock, and other materials. Finding such sources is important in northern Arizona, where : suitable materials may ...

A Multi-Mode Shock Tube for Investigation of Blast-Induced Traumatic Brain Injury

PubMed Central

Reneer, Dexter V.; Hisel, Richard D.; Hoffman, Joshua M.; Kryscio, Richard J.; Lusk, Braden T.

2011-01-01

Abstract Blast-induced mild traumatic brain injury (bTBI) has become increasingly common in recent military conflicts. The mechanisms by which non-impact blast exposure results in bTBI are incompletely understood. Current small animal bTBI models predominantly utilize compressed air-driven membrane rupture as their blast wave source, while large animal models use chemical explosives. The pressure-time signature of each blast mode is unique, making it difficult to evaluate the contributions of the different components of the blast wave to bTBI when using a single blast source. We utilized a multi-mode shock tube, the McMillan blast device, capable of utilizing compressed air- and compressed helium-driven membrane rupture, and the explosives oxyhydrogen and cyclotrimethylenetrinitramine (RDX, the primary component of C-4 plastic explosives) as the driving source. At similar maximal blast overpressures, the positive pressure phase of compressed air-driven blasts was longer, and the positive impulse was greater, than those observed for shockwaves produced by other driving sources. Helium-driven shockwaves more closely resembled RDX blasts, but by displacing air created a hypoxic environment within the shock tube. Pressure-time traces from oxyhydrogen-driven shockwaves were very similar those produced by RDX, although they resulted in elevated carbon monoxide levels due to combustion of the polyethylene bag used to contain the gases within the shock tube prior to detonation. Rats exposed to compressed air-driven blasts had more pronounced vascular damage than those exposed to oxyhydrogen-driven blasts of the same peak overpressure, indicating that differences in blast wave characteristics other than peak overpressure may influence the extent of bTBI. Use of this multi-mode shock tube in small animal models will enable comparison of the extent of brain injury with the pressure-time signature produced using each blast mode, facilitating evaluation of the blast wave components contributing to bTBI. PMID:21083431

A multi-mode shock tube for investigation of blast-induced traumatic brain injury.

PubMed

Reneer, Dexter V; Hisel, Richard D; Hoffman, Joshua M; Kryscio, Richard J; Lusk, Braden T; Geddes, James W

2011-01-01

Blast-induced mild traumatic brain injury (bTBI) has become increasingly common in recent military conflicts. The mechanisms by which non-impact blast exposure results in bTBI are incompletely understood. Current small animal bTBI models predominantly utilize compressed air-driven membrane rupture as their blast wave source, while large animal models use chemical explosives. The pressure-time signature of each blast mode is unique, making it difficult to evaluate the contributions of the different components of the blast wave to bTBI when using a single blast source. We utilized a multi-mode shock tube, the McMillan blast device, capable of utilizing compressed air- and compressed helium-driven membrane rupture, and the explosives oxyhydrogen and cyclotrimethylenetrinitramine (RDX, the primary component of C-4 plastic explosives) as the driving source. At similar maximal blast overpressures, the positive pressure phase of compressed air-driven blasts was longer, and the positive impulse was greater, than those observed for shockwaves produced by other driving sources. Helium-driven shockwaves more closely resembled RDX blasts, but by displacing air created a hypoxic environment within the shock tube. Pressure-time traces from oxyhydrogen-driven shockwaves were very similar those produced by RDX, although they resulted in elevated carbon monoxide levels due to combustion of the polyethylene bag used to contain the gases within the shock tube prior to detonation. Rats exposed to compressed air-driven blasts had more pronounced vascular damage than those exposed to oxyhydrogen-driven blasts of the same peak overpressure, indicating that differences in blast wave characteristics other than peak overpressure may influence the extent of bTBI. Use of this multi-mode shock tube in small animal models will enable comparison of the extent of brain injury with the pressure-time signature produced using each blast mode, facilitating evaluation of the blast wave components contributing to bTBI.

Groundwater maintenance at the vulcan materials quarry in Chattanooga, Tennessee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, R.L.

1985-01-01

The Vulcan Materials Shallowford Road Quarry in Chattanooga, Tennessee is the largest active limestone quarry in the state. Currently it covers some 35 hectares with highwalls up to 100 m. Production is predominately from Middle Ordovician Limestone of the Stones River Group. The upper 60 m consists of medium-bedded gray limestone of the Pond Springs Formation, while the lower 40 m are in Lower Ordovician dolomites and limestones belonging to the Mascot Formation of the Knox Group. The present quarry began in 1951 and has been in continuous operation since that time. For several years the influx of groundwater intomore » the quarry was so great that over 11,355 liters per minute had to be removed by a series of pumps. A source of much of the groundwater was thought to be from Friar Branch which flowed near the present quarry site. At low water, several sinkholes were observed in the bottom of the stream. Several attempts were made (unsuccessfully) to fill these sinks. On July 17, 1984, a 184 m trench was dug along the north side of Friar Branch and fifty-one sections of 1.2 m diameter pipe were placed in the trench. Each 4 m section was made water tight and the water from Friar branch was then diverted into the pipe. Bulldozers scraped the dry bed of Friar Branch in an attempt to locate all major cavities and sinkholes. These were filled with grout and the bed of the creek was covered with about 7 to 8 cm of crushed rock and rolled. The entire stream was sealed with grout and then the stream was returned to its original course. The results was a marked reduction in groundwater seepage into the quarry.« less

Sources Approved for Coverage under the SQCS General Permit in Region 8

EPA Pesticide Factsheets

The sources on Indian country reservation lands that the Region 8 has approved for coverage under the General Air Quality Permit for New and Modified Minor Source Stone Quarrying, Crushing, and Screening Facilities in Indian Country (SQCS General Permit).

Explosion Source Location Study Using Collocated Acoustic and Seismic Networks in Israel

NASA Astrophysics Data System (ADS)

Pinsky, V.; Gitterman, Y.; Arrowsmith, S.; Ben-Horin, Y.

2013-12-01

We explore a joined analysis of seismic and infrasonic signals for improvement in automatic monitoring of small local/regional events, such as construction and quarry blasts, military chemical explosions, sonic booms, etc. using collocated seismic and infrasonic networks recently build in Israel (ISIN) in the frame of the project sponsored by the Bi-national USA-Israel Science Foundation (BSF). The general target is to create an automatic system, which will provide detection, location and identification of explosions in real-time or close-to-real time manner. At the moment the network comprises 15 stations hosting a microphone and seismometer (or accelerometer), operated by the Geophysical Institute of Israel (GII), plus two infrasonic arrays, operated by the National Data Center, Soreq: IOB in the South (Negev desert) and IMA in the North of Israel (Upper Galilee),collocated with the IMS seismic array MMAI. The study utilizes a ground-truth data-base of numerous Rotem phosphate quarry blasts, a number of controlled explosions for demolition of outdated ammunitions and experimental surface explosions for a structure protection research, at the Sayarim Military Range. A special event, comprising four military explosions in a neighboring country, that provided both strong seismic (up to 400 km) and infrasound waves (up to 300 km), is also analyzed. For all of these events the ground-truth coordinates and/or the results of seismic location by the Israel Seismic Network (ISN) have been provided. For automatic event detection and phase picking we tested the new recursive picker, based on Statistically optimal detector. The results were compared to the manual picks. Several location techniques have been tested using the ground-truth event recordings and the preliminary results obtained have been compared to the ground-truth locations: 1) a number of events have been located as intersection of azimuths estimated using the wide-band F-K analysis technique applied to the infrasonic phases of the two distant arrays; 2) a standard robust grid-search location procedure based on phase picks and a constant celerity for a phase (tropospheric or stratospheric) was applied; 3) a joint coordinate grid-search procedure using array waveforms and phase picks was tested, 4) the Bayesian Infrasonic Source Localization (BISL) method, incorporating semi-empirical model-based prior information, was modified for array+network configuration and applied to the ground-truth events. For this purpose we accumulated data of the former observations of the air-to-ground infrasonic phases to compute station specific ground-truth Celerity-Range Histograms (ssgtCRH) and/or model-based CRH (mbCRH), which allow to essentially improve the location results. For building the mbCRH the local meteo-data and the ray-tracing modeling in 3 available azimuth ranges, accounting seasonal variations of winds directivity (quadrants North:315-45, South: 135-225, East 45-135) have been used.

Atmospheric emission of NOx from mining explosives: A critical review

NASA Astrophysics Data System (ADS)

Oluwoye, Ibukun; Dlugogorski, Bogdan Z.; Gore, Jeff; Oskierski, Hans C.; Altarawneh, Mohammednoor

2017-10-01

High-energy materials such as emulsions, slurries and ammonium-nitrate fuel-oil (ANFO) explosives play crucial roles in mining, quarrying, tunnelling and many other infrastructure activities, because of their excellent transport and blasting properties. These explosives engender environmental concerns, due to atmospheric pollution caused by emission of dust and nitrogen oxides (NOx) from blasts, the latter characterised by the average emission factor of 5 kg (t AN explosive)-1. This first-of-its-kind review provides a concise literature account of the formation of NOx during blasting of AN-based explosives, employed in surface operations. We estimate the total NOx emission rate from AN-based explosives as 0.05 Tg (i.e., 5 × 104 t) N per annum, compared to the total global annual anthropogenic NOx emissions of 41.3 × 106 t N y-1. Although minor in the global sense, the large localised plumes from blasting exhibit high NOx concentration (500 ppm) exceeding up to 3000 times the international standards. This emission has profound consequences at mining sites and for adjacent atmospheric environment, necessitating expensive management of exclusion zones. The review describes different types of AN energetic materials for civilian applications, and summarises the essential properties and terminologies pertaining to their use. Furthermore, we recapitulate the mechanisms that lead to the formation of the reactive nitrogen species in blasting of AN-based explosives, review their implications to atmospheric air pollution, and compare the mechanisms with those experienced in other thermal and combustion operations. We also examine the mitigation approaches, including guidelines and operational-control measures. The review discusses the abatement technologies such as the formulation of new explosive mixtures, comprising secondary fuels, spin traps and other additives, in light of their effectiveness and efficiency. We conclude the review with a summary of unresolved problems, identifying possible future developments and their impacts on the environment with emphasis on local and workplace loads.

Determination of Destress Blasting Effectiveness Using Seismic Source Parameters

NASA Astrophysics Data System (ADS)

Wojtecki, Łukasz; Mendecki, Maciej J.; Zuberek, Wacaław M.

2017-12-01

Underground mining of coal seams in the Upper Silesian Coal Basin is currently performed under difficult geological and mining conditions. The mining depth, dislocations (faults and folds) and mining remnants are responsible for rockburst hazard in the highest degree. This hazard can be minimized by using active rockburst prevention, where destress blastings play an important role. Destress blastings in coal seams aim to destress the local stress concentrations. These blastings are usually performed from the longwall face to decrease the stress level ahead of the longwall. An accurate estimation of active rockburst prevention effectiveness is important during mining under disadvantageous geological and mining conditions, which affect the risk of rockburst. Seismic source parameters characterize the focus of tremor, which may be useful in estimating the destress blasting effects. Investigated destress blastings were performed in coal seam no. 507 during its longwall mining in one of the coal mines in the Upper Silesian Coal Basin under difficult geological and mining conditions. The seismic source parameters of the provoked tremors were calculated. The presented preliminary investigations enable a rapid estimation of the destress blasting effectiveness using seismic source parameters, but further analysis in other geological and mining conditions with other blasting parameters is required.

Monitoring Stone Degradation on Coastal Structures in the Great Lakes - Summary Report

DTIC Science & Technology

2005-06-01

Iron Mountain Quarry, Iron Mountain, MI). The Iron Mountain Quarry produces taconite . c. Quarry sample microstructural analyses. Microstructural...Iron Mountain Quarry, Iron Mountain, MI. The Iron Mountain Quarry produces taconite . Also, stone from a tenth quarry (Cedarville Quarry, Cedarville, MI...Quarry, Iron Mountain, MI). The Iron Mountain Quarry produces taconite . Samples of taconite from the Iron Mountain Quarry also were evaluated by

Suitability of bedrock for construction stone in the Greenville 1° by 2° Quadrangle, South Carolina, Georgia, and North Carolina

USGS Publications Warehouse

D'Agostino, John P.; Horton, J. Wright; Nelson, Arthur E.; Clarke, James W.

1993-01-01

This map presents a qualitative regional assessment of the resource potential of bedrock for use as construction stone the the Greenville 1° by 2° quadrangle. Other studies will include metallic minerals (D'Agostine and others, in press a), gold (D'Agostino an others, in press b), and non-metallic commodities (D'Agostino and others, in press c). Construction stone, as used here in the context of bedrock suitability, refers mainly to dimension stone and crushed stone. Abundant supplies of bedrock and alluvial sand and gravel are available from numerous sources in the quadrangle. There is a modern quarry industry with 176 active and inactive quarries situated in the quadrangle--153 in Georgia, 23 in South Carolina, and one in North Carolina. Sixty-five dimension-stone quarries are located in a single granite mass, the Elberton Granite, in Elbert, Madison, and Oglethorpe Counties, Ga. There are numerous undeveloped sources of moderate amounts of stream sand and gravel and major abundant upland residual clay deposits in the quadrangle area.

Stable isotopes back-track the origin of alabaster from the 'Ulrich Epitaph', Güstrow, Germany

NASA Astrophysics Data System (ADS)

Böttcher, Michael E.; Fuchs, Arnold; Gehre, Matthias; Krempler, Michael; Cooper, Anthony H.

2017-04-01

Natural calcium sulphate minerals (like gypsum, in the variety of 'alabaster') have been used for a long time for art and ornamental works despite its high solubility in aqueous solution due to its easy way of recovery and handling. To identify different European source provenances, geochemical and stable isotope forensic methods have been applied, thereby defining historical pathways of trade. A detailed geochemical characterization of both alabaster samples from the monument and potential sources is a pre-requisite for a backtracking material sources. Several tracers have been tested in the past identifiying the coupled sulfur and oxygen isotope composition of the sulfate molecule in the evaporite minerals to be highly characteristic. In the present study, we analyzed the stable sulfur and oxygen isotope composition of raw alabaster from the famous Ulrich Epithaph in Güstrow, Northeastern Germany, and compared the results with new measurements from one of the major European contributors of alabaster in the 16th century, the Cellaston quarry, Derbyshire (England) and literature data for further potential Spanish and Frensh source quarries (Kloppmann et a., 2014; Archaeometry, 56). We found that the stable sulfur and oxygen isotope signatures of alabaster from the Ulrich Epitaph indicate the origin from the Upper Triassic (Keuper) evaporites of the English Cellaston quarry and are not related to other potential alabaster sources. This further illustrates the alabaster trade way between England and Germany in the late 16th century.

30 CFR 56.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Extraneous Electricity § 56.6605 Isolation of blasting circuits. Lead wires and blasting lines shall be... sources of stray or static electricity. Blasting circuits shall be protected from any contact between...

30 CFR 56.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Extraneous Electricity § 56.6605 Isolation of blasting circuits. Lead wires and blasting lines shall be... sources of stray or static electricity. Blasting circuits shall be protected from any contact between...

30 CFR 56.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Extraneous Electricity § 56.6605 Isolation of blasting circuits. Lead wires and blasting lines shall be... sources of stray or static electricity. Blasting circuits shall be protected from any contact between...

30 CFR 56.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Extraneous Electricity § 56.6605 Isolation of blasting circuits. Lead wires and blasting lines shall be... sources of stray or static electricity. Blasting circuits shall be protected from any contact between...

30 CFR 56.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Extraneous Electricity § 56.6605 Isolation of blasting circuits. Lead wires and blasting lines shall be... sources of stray or static electricity. Blasting circuits shall be protected from any contact between...

On the Interaction and Coalescence if Spherical Blast Waves

NASA Technical Reports Server (NTRS)

Kandula, Max; Freeman, Robert J.

2005-01-01

The scaling and similarity laws concerning the propagation of isolated spherical blast waves are briefly reviewed. Both point source explosions and high pressure gas explosions are considered. Test data on blast overpressure from the interaction and coalescence of spherical blast waves emanating from explosives in the form of shaped charges of different strength placed in the vicinity of a solid propellant stack are presented. These data are discussed with regard to the scaling laws concerning the decay of blast overpressure. The results point out the possibility of detecting source explosions from far-field pressure measurements.

Probabilistic prediction models for aggregate quarry siting

USGS Publications Warehouse

Robinson, G.R.; Larkins, P.M.

2007-01-01

Weights-of-evidence (WofE) and logistic regression techniques were used in a GIS framework to predict the spatial likelihood (prospectivity) of crushed-stone aggregate quarry development. The joint conditional probability models, based on geology, transportation network, and population density variables, were defined using quarry location and time of development data for the New England States, North Carolina, and South Carolina, USA. The Quarry Operation models describe the distribution of active aggregate quarries, independent of the date of opening. The New Quarry models describe the distribution of aggregate quarries when they open. Because of the small number of new quarries developed in the study areas during the last decade, independent New Quarry models have low parameter estimate reliability. The performance of parameter estimates derived for Quarry Operation models, defined by a larger number of active quarries in the study areas, were tested and evaluated to predict the spatial likelihood of new quarry development. Population density conditions at the time of new quarry development were used to modify the population density variable in the Quarry Operation models to apply to new quarry development sites. The Quarry Operation parameters derived for the New England study area, Carolina study area, and the combined New England and Carolina study areas were all similar in magnitude and relative strength. The Quarry Operation model parameters, using the modified population density variables, were found to be a good predictor of new quarry locations. Both the aggregate industry and the land management community can use the model approach to target areas for more detailed site evaluation for quarry location. The models can be revised easily to reflect actual or anticipated changes in transportation and population features. ?? International Association for Mathematical Geology 2007.

WImpiBLAST: web interface for mpiBLAST to help biologists perform large-scale annotation using high performance computing.

PubMed

Sharma, Parichit; Mantri, Shrikant S

2014-01-01

The function of a newly sequenced gene can be discovered by determining its sequence homology with known proteins. BLAST is the most extensively used sequence analysis program for sequence similarity search in large databases of sequences. With the advent of next generation sequencing technologies it has now become possible to study genes and their expression at a genome-wide scale through RNA-seq and metagenome sequencing experiments. Functional annotation of all the genes is done by sequence similarity search against multiple protein databases. This annotation task is computationally very intensive and can take days to obtain complete results. The program mpiBLAST, an open-source parallelization of BLAST that achieves superlinear speedup, can be used to accelerate large-scale annotation by using supercomputers and high performance computing (HPC) clusters. Although many parallel bioinformatics applications using the Message Passing Interface (MPI) are available in the public domain, researchers are reluctant to use them due to lack of expertise in the Linux command line and relevant programming experience. With these limitations, it becomes difficult for biologists to use mpiBLAST for accelerating annotation. No web interface is available in the open-source domain for mpiBLAST. We have developed WImpiBLAST, a user-friendly open-source web interface for parallel BLAST searches. It is implemented in Struts 1.3 using a Java backbone and runs atop the open-source Apache Tomcat Server. WImpiBLAST supports script creation and job submission features and also provides a robust job management interface for system administrators. It combines script creation and modification features with job monitoring and management through the Torque resource manager on a Linux-based HPC cluster. Use case information highlights the acceleration of annotation analysis achieved by using WImpiBLAST. Here, we describe the WImpiBLAST web interface features and architecture, explain design decisions, describe workflows and provide a detailed analysis.

WImpiBLAST: Web Interface for mpiBLAST to Help Biologists Perform Large-Scale Annotation Using High Performance Computing

PubMed Central

Sharma, Parichit; Mantri, Shrikant S.

2014-01-01

The function of a newly sequenced gene can be discovered by determining its sequence homology with known proteins. BLAST is the most extensively used sequence analysis program for sequence similarity search in large databases of sequences. With the advent of next generation sequencing technologies it has now become possible to study genes and their expression at a genome-wide scale through RNA-seq and metagenome sequencing experiments. Functional annotation of all the genes is done by sequence similarity search against multiple protein databases. This annotation task is computationally very intensive and can take days to obtain complete results. The program mpiBLAST, an open-source parallelization of BLAST that achieves superlinear speedup, can be used to accelerate large-scale annotation by using supercomputers and high performance computing (HPC) clusters. Although many parallel bioinformatics applications using the Message Passing Interface (MPI) are available in the public domain, researchers are reluctant to use them due to lack of expertise in the Linux command line and relevant programming experience. With these limitations, it becomes difficult for biologists to use mpiBLAST for accelerating annotation. No web interface is available in the open-source domain for mpiBLAST. We have developed WImpiBLAST, a user-friendly open-source web interface for parallel BLAST searches. It is implemented in Struts 1.3 using a Java backbone and runs atop the open-source Apache Tomcat Server. WImpiBLAST supports script creation and job submission features and also provides a robust job management interface for system administrators. It combines script creation and modification features with job monitoring and management through the Torque resource manager on a Linux-based HPC cluster. Use case information highlights the acceleration of annotation analysis achieved by using WImpiBLAST. Here, we describe the WImpiBLAST web interface features and architecture, explain design decisions, describe workflows and provide a detailed analysis. PMID:24979410

Contributions of human activities to suspended sediment yield during storm events from a small, steep, tropical watershed

NASA Astrophysics Data System (ADS)

Messina, A. M.; Biggs, T. W.

2016-07-01

Suspended sediment concentrations (SSC) and yields (SSY) were measured during storm and non-storm periods from undisturbed and human-disturbed portions of a small (1.8 km2), mountainous watershed that drains to a sediment-stressed coral reef. Event-wise SSY (SSYEV) was calculated for 142 storms from measurements of water discharge (Q), turbidity (T), and SSC measured downstream of three key sediment sources: undisturbed forest, an aggregate quarry, and a village. SSC and SSYEV were significantly higher downstream of the quarry during both storm- and non-storm periods. The human-disturbed subwatershed (10.1% disturbed) accounted for an average of 87% of SSYEV from the watershed. Observed sediment yield (mass) to the coast, including human disturbed subwatersheds, was 3.9× the natural background. Specific SSY (mass/area) from the disturbed quarry area was 49× higher than from natural forest compared with 8× higher from the village area. Similar to mountainous watersheds in semi-arid and temperate climates, SSYEV from both the undisturbed and disturbed watersheds correlated closely with maximum event discharge (Qmax), event total precipitation and event total Q, but not with the Erosivity Index. Best estimates of annual SSY varied by method, from 45 to 143 tons/km2/yr from the undisturbed subwatershed, 441-598 tons/km2/yr from the human-disturbed subwatershed, and 241-368 tons/km2/yr from the total watershed. Sediment yield was very sensitive to disturbance; the quarry covers 1.1% of the total watershed area, but contributed 36% of SSYEV. Given the limited access to gravel for infrastructure development, sediment disturbance from local aggregate mining may be a critical sediment source on remote islands in the Pacific and elsewhere. Identification of erosion hotspots like the quarry using rapid, event-wise measures of suspended sediment yield will help efforts to mitigate sediment stress and restore coral reefs.

Erasmus Syndrome: Association of Silicosis and Systemic Sclerosis.

PubMed

Sharma, Reena K; Sharma, Anjna K; Sharma, Anuj

2018-01-01

Silicosis is an inflammatory disease of the lung characterized by irreversible lung fibrosis which develops from prolonged pulmonary inhalation and retention of crystalline silica and immune reaction. It mainly appears as an occupational hazard in persons involved in stone-quarrying, mining, and sand blasting. Crystalline silica is not only known to be responsible for silicosis but also for other autoimmune diseases including systemic lupus erythematosus (SLE), rheumatoid arthritis (RA)-Caplan syndrome, systemic sclerosis (SSc), and antineutrophil cytoplasmic antibody (ANCA)-related vasculitis. Erasmus syndrome is the association of silica exposure and subsequent development of SSc. The limited numbers of cases reported in the literature were miners and only sporadically involved in other professionals. Here, we report a case of a 52 -year-old stone cutter who developed silicosis and SSc after 25 years of exposure.

Understanding intraplate earthquakes in Sweden: the where and why

NASA Astrophysics Data System (ADS)

Lund, Björn; Tryggvason, Ari; Chan, NeXun; Högdahl, Karin; Buhcheva, Darina; Bödvarsson, Reynir

2016-04-01

The Swedish National Seismic Network (SNSN) underwent a rapid expansion and modernization between the years 2000 - 2010. The number of stations increased from 6 to 65, all broadband or semi-broadband with higher than standard sensitivity and all transmitting data in real-time. This has lead to a significant increase in the number of detected earthquakes, with the magnitude of completeness being approximately ML 0.5 within the network. During the last 15 years some 7,300 earthquakes have been detected and located, which can be compared to the approximately 1,800 earthquakes in the Swedish catalog from 1375 to 1999. We have used the recent earthquake catalog and various antropogenic sources (e.g. mine blasts, quarry blasts and infrastructure construction blast) to derive low resolution 3D P- and S-wave velocity models for entire Sweden. Including the blasts provides a more even geographical distribution of sources as well as good constraints on the locations. The resolution of the derived velocity models is in the 20 km range in the well resolved areas. A fairly robust feature observed in the Vp/Vs ratio of the derived models is a difference between the Paleoproterozoic rocks belonging to the TIB (Transscanidinavian Igneous Belt) and the Svecofennian rocks east and north of this region (a Vp/Vs ratio about 1.72 prevail in the former compared to a value below 1.70 in the latter) at depths down to 15 km. All earthquakes occurring since 2000 have been relocated in the 3D velocity model. The results show very clear differences in how earthquakes occur in different parts of Sweden. In the north, north of approximately 64 degrees latitude, most earthquakes occur on or in the vicinity of the Holocene postglacial faults. From 64N to approximately 60N earthquake activity is concentrated along the northeast coast line, with some relation to the offset in the bedrock from the onshore area to the offshore Bay of Bothnia. In southern Sweden earthquake activity is more widely distributed, with a concentration in a band across Lake Vänern, following the boundary between the TIB and the Sveconorwegian orogenic belt. We identify a number of earthquake lineaments in the country and relate these to very different geological units and boundaries, from old Paleoproterozoic features to the youngest postglacial faults. We show how earthquake depths vary in the different seismically active regions, and identify events occurring down to 40 km depth in the crust. Focal mechanisms show that in much of Sweden strike-slip faulting dominates at seismogenic depths. There are however systematic variations within the country. Inverting the mechanisms for the stress field indicates that the maximum horizontal stress direction is NW-SE, in agreement with ridge-push, in much of the country. We will discuss other possible driving mechanisms, such as the ongoing postglacial rebound.

Quantification of neotectonic stress orientations and magnitudes from field observations in Finnmark, northern Norway

NASA Astrophysics Data System (ADS)

Pascal, Christophe; Roberts, David; Gabrielsen, Roy H.

2005-05-01

Fieldwork was conducted in Finnmark, northern Norway, with the purpose of detecting and measuring stress-relief features, induced by quarrying and road works, and to derive from them valuable information on the shallow-crustal stress orientations and magnitudes. Two kinds of stress-relief features were considered in this study. The first consists of drillhole offsets that were found along blasted road-cuts and which were triggered by the sudden rock unloading following the actual blasting. Vertical axial fractures found in the concave remains of boreholes represent the second kind of stress-relief feature. The axial fractures are tension fractures produced by gas overpressure inside the drillhole when the blast occurs. As such, their strike reflects the orientation of the ambient maximum horizontal stress axis. The borehole offsets show mostly reverse-slip displacements to the E-SE and the axial fractures trend NW-SE on average, in agreement with NW-SE compression induced by North Atlantic ridge-push forces. Mechanical considerations of the slip planes offsetting some of the drillholes lead to the conclusion that the magnitude of the maximum horizontal stress at the surface is in the range ˜0.1-˜1 MPa. This range of magnitudes is 1-2 orders less than the horizontal stress magnitudes measured at the surface in other post-glacial environments (e.g. Canada). It is suggested that this difference is related to the marked decline in stress that followed the tremendous post-glacial burst of earthquake activity that affected Fennoscandia but apparently not the Canadian Shield.

Support Vector Machine Model for Automatic Detection and Classification of Seismic Events

NASA Astrophysics Data System (ADS)

Barros, Vesna; Barros, Lucas

2016-04-01

The automated processing of multiple seismic signals to detect, localize and classify seismic events is a central tool in both natural hazards monitoring and nuclear treaty verification. However, false detections and missed detections caused by station noise and incorrect classification of arrivals are still an issue and the events are often unclassified or poorly classified. Thus, machine learning techniques can be used in automatic processing for classifying the huge database of seismic recordings and provide more confidence in the final output. Applied in the context of the International Monitoring System (IMS) - a global sensor network developed for the Comprehensive Nuclear-Test-Ban Treaty (CTBT) - we propose a fully automatic method for seismic event detection and classification based on a supervised pattern recognition technique called the Support Vector Machine (SVM). According to Kortström et al., 2015, the advantages of using SVM are handleability of large number of features and effectiveness in high dimensional spaces. Our objective is to detect seismic events from one IMS seismic station located in an area of high seismicity and mining activity and classify them as earthquakes or quarry blasts. It is expected to create a flexible and easily adjustable SVM method that can be applied in different regions and datasets. Taken a step further, accurate results for seismic stations could lead to a modification of the model and its parameters to make it applicable to other waveform technologies used to monitor nuclear explosions such as infrasound and hydroacoustic waveforms. As an authorized user, we have direct access to all IMS data and bulletins through a secure signatory account. A set of significant seismic waveforms containing different types of events (e.g. earthquake, quarry blasts) and noise is being analysed to train the model and learn the typical pattern of the signal from these events. Moreover, comparing the performance of the support-vector network to various classical learning algorithms used before in seismic detection and classification is an essential final step to analyze the advantages and disadvantages of the model.

INTERIOR VIEW, NORTH QUARRY, AN ACTIVE DOLOMITE QUARRY, LOOKING NORTH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, AN ACTIVE DOLOMITE QUARRY, LOOKING NORTH TO THE POWER PLANT OF THE HISTORIC THOMAS COKEWORKS SITE. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

30 CFR 57.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Extraneous Electricity-Surface and Underground § 57.6605 Isolation of blasting circuits. Lead wires and... shall be protected from sources of stray or static electricity. Blasting circuits shall be protected...

30 CFR 57.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Extraneous Electricity-Surface and Underground § 57.6605 Isolation of blasting circuits. Lead wires and... shall be protected from sources of stray or static electricity. Blasting circuits shall be protected...

30 CFR 57.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Extraneous Electricity-Surface and Underground § 57.6605 Isolation of blasting circuits. Lead wires and... shall be protected from sources of stray or static electricity. Blasting circuits shall be protected...

30 CFR 57.6605 - Isolation of blasting circuits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Extraneous Electricity-Surface and Underground § 57.6605 Isolation of blasting circuits. Lead wires and... shall be protected from sources of stray or static electricity. Blasting circuits shall be protected...

Improved phase arrival estimate and location for local earthquakes in South Korea

NASA Astrophysics Data System (ADS)

Morton, E. A.; Rowe, C. A.; Begnaud, M. L.

2012-12-01

The Korean Institute of Geoscience and Mineral Resources (KIGAM) and the Korean Meteorological Agency (KMA) regularly report local (distance < ~1200 km) seismicity recorded with their networks; we obtain preliminary event location estimates as well as waveform data, but no phase arrivals are reported, so the data are not immediately useful for earthquake location. Our goal is to identify seismic events that are sufficiently well-located to provide accurate seismic travel-time information for events within the KIGAM and KMA networks, and also recorded by some regional stations. Toward that end, we are using a combination of manual phase identification and arrival-time picking, with waveform cross-correlation, to cluster events that have occurred in close proximity to one another, which allows for improved phase identification by comparing the highly correlating waveforms. We cross-correlate the known events with one another on 5 seismic stations and cluster events that correlate above a correlation coefficient threshold of 0.7, which reveals few clusters containing few events each. The small number of repeating events suggests that the online catalogs have had mining and quarry blasts removed before publication, as these can contribute significantly to repeating seismic sources in relatively aseismic regions such as South Korea. The dispersed source locations in our catalog, however, are ideal for seismic velocity modeling by providing superior sampling through the dense seismic station arrangement, which produces favorable event-to-station ray path coverage. Following careful manual phase picking on 104 events chosen to provide adequate ray coverage, we re-locate the events to obtain improved source coordinates. The re-located events are used with Thurber's Simul2000 pseudo-bending local tomography code to estimate the crustal structure on the Korean Peninsula, which is an important contribution to ongoing calibration for events of interest in the region.

Geophysical investigations of the Anna, Ohio earthquake zone. Annual progess report July 1979-June 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mauk, F.J.; Henry, S.G.; Christensen, D.H.

The Anna, Ohio seismic array, converted to solar recharge power systems, has been in continuous operation. No local earthquakes above m sub b 1.5 have occurred. Near regional earthquakes from 1977 through 1980 supplemented with quarry blast recordings have been used to determine the regional travel time curves. Theoretical estimates of earthquake detection and location capabilities for m sub b 2.5, 2.0, and 1.5 earthquakes in the Anna, Ohio region are included to demonstrate the coverage effectiveness of the network. Teleseismic P-wave residuals as a function of azimuth are included to demonstrate the lower crustal velocity variation for the region.more » Finally, an exhaustive catalog of water and gas well data is included from which a regional depth to bedrock map has been produced.« less

Magnetic properties and element concentrations in lichens exposed to airborne pollutants released during cement production.

PubMed

Paoli, Luca; Winkler, Aldo; Guttová, Anna; Sagnotti, Leonardo; Grassi, Alice; Lackovičová, Anna; Senko, Dušan; Loppi, Stefano

2017-05-01

The content of selected elements (Al, As, Ca, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, S, Ti, V and Zn) was measured in samples of the lichen Evernia prunastri exposed for 30, 90 and 180 days around a cement mill, limestone and basalt quarries and urban and agricultural areas in SW Slovakia. Lichens transplanted around the investigated quarries and the cement mill rapidly (30 days) reflected the deposition of dust-associated elements, namely Ca (at the cement mill and the limestone quarry) and Fe, Ti and V (around the cement mill and the basalt quarry), and their content remained significantly higher throughout the whole period (30-180 days) with respect to the surrounding environment. Airborne pollutants (such as S) progressively increased in the study area from 30 to 180 days. The magnetic properties of lichen transplants exposed for 180 days have been characterized and compared with those of native lichens (Xanthoria parietina) and neighbouring bark, soil and rock samples, in order to test the suitability of native and transplanted samples as air pollution magnetic biomonitors. The magnetic mineralogy was homogeneous in all samples, with the exception of the samples from the basalt quarry. The transplants showed excellent correlations between the saturation remanent magnetization (Mrs) and the content of Fe. Native samples had a similar magnetic signature, but the values of the concentration-dependent magnetic parameters were up to two orders of magnitude higher, reflecting higher concentrations of magnetic particles. The concentrations of As, Ca and Cr in lichens correlated with Mrs values after neglecting the samples from the basalt quarry, which showed distinct magnetic properties, suggesting the cement mill as a likely source. Conversely, Ti and Mn were mostly (but not exclusively) associated with dust from the basalt quarry. It is suggested that the natural geological characteristics of the substrate may strongly affect the magnetic properties of lichen thalli. Taking this into account, the results of this study point out the suitability of lichens as air pollution magnetic biomonitors.

Effect of Blast Injury on Auditory Localization in Military Service Members.

PubMed

Kubli, Lina R; Brungart, Douglas; Northern, Jerry

Among the many advantages of binaural hearing are the abilities to localize sounds in space and to attend to one sound in the presence of many sounds. Binaural hearing provides benefits for all listeners, but it may be especially critical for military personnel who must maintain situational awareness in complex tactical environments with multiple speech and noise sources. There is concern that Military Service Members who have been exposed to one or more high-intensity blasts during their tour of duty may have difficulty with binaural and spatial ability due to degradation in auditory and cognitive processes. The primary objective of this study was to assess the ability of blast-exposed Military Service Members to localize speech sounds in quiet and in multisource environments with one or two competing talkers. Participants were presented with one, two, or three topic-related (e.g., sports, food, travel) sentences under headphones and required to attend to, and then locate the source of, the sentence pertaining to a prespecified target topic within a virtual space. The listener's head position was monitored by a head-mounted tracking device that continuously updated the apparent spatial location of the target and competing speech sounds as the subject turned within the virtual space. Measurements of auditory localization ability included mean absolute error in locating the source of the target sentence, the time it took to locate the target sentence within 30 degrees, target/competitor confusion errors, response time, and cumulative head motion. Twenty-one blast-exposed Active-Duty or Veteran Military Service Members (blast-exposed group) and 33 non-blast-exposed Service Members and beneficiaries (control group) were evaluated. In general, the blast-exposed group performed as well as the control group if the task involved localizing the source of a single speech target. However, if the task involved two or three simultaneous talkers, localization ability was compromised for some participants in the blast-exposed group. Blast-exposed participants were less accurate in their localization responses and required more exploratory head movements to find the location of the target talker. Results suggest that blast-exposed participants have more difficulty than non-blast-exposed participants in localizing sounds in complex acoustic environments. This apparent deficit in spatial hearing ability highlights the need to develop new diagnostic tests using complex listening tasks that involve multiple sound sources that require speech segregation and comprehension.

Preliminary report on the Black Thunder, Wyoming CTBT R and D experiment quicklook report: LLNL input from regional stations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harben, P.E.; Glenn, L.A.

This report presents a preliminary summary of the data recorded at three regional seismic stations from surface blasting at the Black Thunder Coal Mine in northeast Wyoming. The regional stations are part of a larger effort that includes many more seismic stations in the immediate vicinity of the mine. The overall purpose of this effort is to characterize the source function and propagation characteristics of large typical surface mine blasts. A detailed study of source and propagation features of conventional surface blasts is a prerequisite to attempts at discriminating this type of blasting activity from other sources of seismic events.more » The Black Thunder Seismic experiment is a joint verification effort to determine seismic source and path effects that result from very large, but routine ripple-fired surface mining blasts. Studies of the data collected will be for the purpose of understanding how the near-field and regional seismic waveforms from these surface mining blasts are similar to, and different from, point shot explosions and explosions at greater depth. The Black Hills Station is a Designated Seismic Station that was constructed for temporary occupancy by the Former Soviet Union seismic verification scientists in accordance with the Threshold Test Ban Treaty protocol.« less

Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

NASA Astrophysics Data System (ADS)

Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

2013-04-01

The ancient coastal quarries of Mediterranean are increasingly considered geosites of multidisciplinary relevance. They are sites of historical-archaeological interest that show ancient techniques of stone extraction; they are significant for cultural heritage conservation and restoration, as sources of the stones used in ancient buildings and monuments; they are sites of geological relevance, as often retain important stratigraphic sections; they are also useful markers of secular changes in the sea level. A multisciplinary study is in progress on the ancient quarries of the Sinis region (western Sardinia island), integrating archaeological, geological, minero-petrographical data. In Sardinia, coastal quarries have been established from Punic and Roman times. Many of them exploited Quaternary sediments along the southern and western coasts of the island. They consist of middle-late Pleistocene marine conglomerates and carbonate sandstones, and of coastal (aeolian) carbonate sandstones. Sandstone blocks of different sizes have been widely used in ancient cities for buildings, defensive works, harbours, etc. Three main areas of stone extraction (San Giovanni di Sinis, Punta Maimoni, Is Arutas) have been so far recognized in the Sinis. GIS-supported mapping and documentation of the sites includes their geology and stratigraphy, the extension and layout of the quarries, and an evaluation of volumes of extracted rocks. Documented archaeological evidences include ancient extraction fronts, spoil heaps, working areas, working traces in the old fronts, transport routes of blocks, and traces of loading facilities. The study is aimed at reconstructing the relationships of the quarries with the urban areas of Sinis, as the ancient Punic-Roman city of Tharros. Consequently, a minero-petrographical characterization (optical microscopy, XRD) is performed on sandstones sampled in each quarry, and in historical buildings in Tharros and other centres of the region (Cabras, Oristano, Santa Giusta). They are prevailing fine-medium grained carbonate sandstones, and subordinate coarse sandstones and micro-conglomerates, variably cemented. In the studied areas, stratigraphic sequences grade from coarser facies of marine environment to fine-grained aeolian deposits, marked by cross-stratification. The Quaternary sedimentary sequence rests on Miocene limestones and clays, and on Plio-Pleistocene basalts. On optical microscopy, sandstones show grain-supported texture, with abundant carbonate bioclasts, intraclasts and algal nodules, with quartz, feldspars and fragments of granitoids, quartzites, volcanics. Grainsize in sandstone sequences progressively decreases towards the top, corresponding to an increase of fine bioclastic components. Terrigenous components change from the northernmost outcrops (Is Arutas quarries), where clasts of granitoid origin are dominant, to the southern outcrops (San Giovanni di Sinis quarries), which show a more marked compositional heterogeneity, with frequent volcanic feldspars and lithoclasts. The calcitic cement also shows distinct variations, both along the stratigraphic sequence and at areal scale, between the sparitic type and the micro/cryptocrystalline type. First evidences on samples from Tharros city walls indicate that sandstone blocks may come, almost in part, from the quarries of San Giovanni di Sinis that, consequently, could have started to work during the Punic age. Other evidences in the area, however, indicate that quarrying activities in Sinis continued well over the Ancient times, presumably including all the Middle Ages.

The air's got to be far cleaner here: a discursive analysis of place-identity threat.

PubMed

Hugh-Jones, Siobhan; Madill, Anna

2009-12-01

That talk is never disinterested complicates the relationship between the environment and the claims people make about it. Talk about place, and one's self in it, is particularly complex when the environment poses risk or is otherwise problematized. This study, a secondary analysis of interview data, seeks to extend discursive work on place-identity by examining the ways in which 14 residents of a small English village talk about themselves and their locale. The locale accommodates an active quarry, and many residents had lodged complaints to the quarry about dust, noise and vibrations from blasting. Attention to the interactional context of the interviews illustrates the ways in which (simply) interviewing people about their locale can threaten self- and place-identity. When asked about life in the village, interviewees oriented to two main dilemmas in protecting self- and place-identity: (1) how to justify continued residence in a challenging environment and (2) how to complain about the locale whilst maintaining positive place-identity. Discursive responses to these dilemmas drew upon typical identity processes, such as self- and place distinctiveness and the formulation of out-groups, as well as upon constructions of localized power-sharing and morally obligated tolerance of risk. We suggest that research on problematical places, and of environmental risk, needs to be sensitized to how it may constitute a threat to self- and place-identity, and how this may mediate formulations self and place, as well as of environmental risk.

30 CFR 56.6404 - Separation of blasting circuits from power source.

Code of Federal Regulations, 2010 CFR

2010-07-01

... LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL... when closed to fire the blast. (b) Lead wires shall not be connected to the blasting switch until the...

Improving ground-penetrating radar data in sedimentary rocks using deterministic deconvolution

USGS Publications Warehouse

Xia, J.; Franseen, E.K.; Miller, R.D.; Weis, T.V.; Byrnes, A.P.

2003-01-01

Resolution is key to confidently identifying unique geologic features using ground-penetrating radar (GPR) data. Source wavelet "ringing" (related to bandwidth) in a GPR section limits resolution because of wavelet interference, and can smear reflections in time and/or space. The resultant potential for misinterpretation limits the usefulness of GPR. Deconvolution offers the ability to compress the source wavelet and improve temporal resolution. Unlike statistical deconvolution, deterministic deconvolution is mathematically simple and stable while providing the highest possible resolution because it uses the source wavelet unique to the specific radar equipment. Source wavelets generated in, transmitted through and acquired from air allow successful application of deterministic approaches to wavelet suppression. We demonstrate the validity of using a source wavelet acquired in air as the operator for deterministic deconvolution in a field application using "400-MHz" antennas at a quarry site characterized by interbedded carbonates with shale partings. We collected GPR data on a bench adjacent to cleanly exposed quarry faces in which we placed conductive rods to provide conclusive groundtruth for this approach to deconvolution. The best deconvolution results, which are confirmed by the conductive rods for the 400-MHz antenna tests, were observed for wavelets acquired when the transmitter and receiver were separated by 0.3 m. Applying deterministic deconvolution to GPR data collected in sedimentary strata at our study site resulted in an improvement in resolution (50%) and improved spatial location (0.10-0.15 m) of geologic features compared to the same data processed without deterministic deconvolution. The effectiveness of deterministic deconvolution for increased resolution and spatial accuracy of specific geologic features is further demonstrated by comparing results of deconvolved data with nondeconvolved data acquired along a 30-m transect immediately adjacent to a fresh quarry face. The results at this site support using deterministic deconvolution, which incorporates the GPR instrument's unique source wavelet, as a standard part of routine GPR data processing. ?? 2003 Elsevier B.V. All rights reserved.

NOBLAST and JAMBLAST: New Options for BLAST and a Java Application Manager for BLAST results.

PubMed

Lagnel, Jacques; Tsigenopoulos, Costas S; Iliopoulos, Ioannis

2009-03-15

NOBLAST (New Options for BLAST) is an open source program that provides a new user-friendly tabular output format for various NCBI BLAST programs (Blastn, Blastp, Blastx, Tblastn, Tblastx, Mega BLAST and Psi BLAST) without any use of a parser and provides E-value correction in case of use of segmented BLAST database. JAMBLAST using the NOBLAST output allows the user to manage, view and filter the BLAST hits using a number of selection criteria. A distribution package of NOBLAST and JAMBLAST including detailed installation procedure is freely available from http://sourceforge.net/projects/JAMBLAST/ and http://sourceforge.net/projects/NOBLAST. Supplementary data are available at Bioinformatics online.

Environmentalism and natural aggregate mining

USGS Publications Warehouse

Drew, L.J.; Langer, W.H.; Sachs, J.S.

2002-01-01

Sustaining a developed economy and expanding a developing one require the use of large volumes of natural aggregate. Almost all human activity (commercial, recreational, or leisure) is transacted in or on facilities constructed from natural aggregate. In our urban and suburban worlds, we are almost totally dependent on supplies of water collected behind dams and transported through aqueducts made from concrete. Natural aggregate is essential to the facilities that produce energy-hydroelectric dams and coal-fired powerplants. Ironically, the utility created for mankind by the use of natural aggregate is rarely compared favorably with the environmental impacts of mining it. Instead, the empty quarries and pits are seen as large negative environmental consequences. At the root of this disassociation is the philosophy of environmentalism, which flavors our perceptions of the excavation, processing, and distribution of natural aggregate. The two end-member ideas in this philosophy are ecocentrism and anthropocentrism. Ecocentrism takes the position that the natural world is a organism whose arteries are the rivers-their flow must not be altered. The soil is another vital organ and must not be covered with concrete and asphalt. The motto of the ecocentrist is "man must live more lightly on the land." The anthropocentrist wants clean water and air and an uncluttered landscape for human use. Mining is allowed and even encouraged, but dust and noise from quarry and pit operations must be minimized. The large volume of truck traffic is viewed as a real menace to human life and should be regulated and isolated. The environmental problems that the producers of natural aggregate (crushed stone and sand and gravel) face today are mostly difficult social and political concerns associated with the large holes dug in the ground and the large volume of heavy truck traffic associated with quarry and pit operations. These concerns have increased in recent years as society's demand for living space has encroached on the sites of production; in other words, the act of production has engendered condemnation. Many other environmental problems that are associated with dust and noise and blasting from quarry and pit operations have been reduced through the efficient use of technology. Recycling concrete in buildings, bridges, and roads and asphaltic pavements will ultimately reduce the demand for virgin natural aggregate. The impact created by the large holes in the ground required for the mining of natural aggregate can be greatly reduced by planning their reclamation before mining begins. ?? 2002 International Association for Mathematical Geology.

Antagonistic perception of a rock-mass as geomorphosite and/or mineral resource with specific concern of natural stone for heritage conservation

NASA Astrophysics Data System (ADS)

Prikryl, Richard

2016-04-01

Prior to industrial era, the quarrying of natural stone was primarily local (the stone has been used very close to its extraction in most of the cases), small scale, occasional (the stone has been extracted only when needed for specific construction, permanent operations were much rarer than nowadays) but long-term (the quarrying activity at one site persisted over centuries very often). The landscape affected by such quarrying (as we can observe it at present) gained numerous new values (e.g., increased morphological contrast, succession of wildlife habitat, etc.) that are often appreciated more than the presence of valuable mineral resource - natural stone. If these site were claimed natural monuments or gained another type of environmental protection, any further extraction of natural stone is prohibited. However, if the specific site was used for extraction of natural stone that has been used for construction which later became cultural heritage object, the antagonistic perception of the site might appear - the site might be protected as a geomorphosite but, at the same time, it can be a source of unique natural stone required for the restoration of cultural heritage objects. This paper, along with above mentioned basic relationships, provides some real examples connected with the difficulties to find the extractable source of natural stone for restoration of iconic cultural heritage objects - specifically search for sources of Carboniferous arkoses to be used for replacement of the decayed ashlars at the Gothic Charles Bridge in Prague (Czech Republic).

OVERALL VIEW OF QUARRY, FACING NORTH, WITH UNQUARRIED GRANITE OUTCROP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OVERALL VIEW OF QUARRY, FACING NORTH, WITH UN-QUARRIED GRANITE OUTCROP IN BACKGROUND - Granite Hill Plantation, Quarry No. 3, South side of State Route 16, 1.3 miles northeast east of Sparta, Sparta, Hancock County, GA

30 CFR 75.1323 - Blasting circuits.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Blasting circuits shall be protected from sources of stray electric current. (b) Detonators made by...) Each wire connection in a blasting circuit shall be— (1) Properly spliced; and (2) Separated from other connections in the circuit to prevent accidental contact and arcing. (h) Uninsulated connections in each...

30 CFR 75.1323 - Blasting circuits.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Blasting circuits shall be protected from sources of stray electric current. (b) Detonators made by...) Each wire connection in a blasting circuit shall be— (1) Properly spliced; and (2) Separated from other connections in the circuit to prevent accidental contact and arcing. (h) Uninsulated connections in each...

Fisher Sand & Gravel New Mexico, Inc. General Air Quality Permit: Related Documents

EPA Pesticide Factsheets

Documents related to the Fisher Sand & Gravel – New Mexico, Inc., Grey Mesa Gravel Pit General Air Quality Permit for New or Modified Minor Source Stone Quarrying, Crushing, and Screening Facilities in Indian Country.

Hydrogeologic controls and geochemical indicators of groundwater movement in the Niles Cone and southern East Bay Plain groundwater subbasins, Alameda County, California

USGS Publications Warehouse

Teague, Nicholas F.; Izbicki, John A.; Borchers, Jim; Kulongoski, Justin T.; Jurgens, Bryant C.

2018-02-01

Beginning in the 1970s, Alameda County Water District began infiltrating imported water through ponds in repurposed gravel quarries at the Quarry Lakes Regional Park, in the Niles Cone groundwater subbasin, to recharge groundwater and to minimize intrusion of saline, San Francisco Bay water into freshwater aquifers. Hydraulic connection between distinct aquifers underlying Quarry Lakes allows water to recharge the upper aquifer system to depths of 400 feet below land surface, and the Deep aquifer to depths of more than 650 feet. Previous studies of the Niles Cone and southern East Bay Plain groundwater subbasins suggested that these two subbasins may be hydraulically connected. Characterization of storage capacities and hydraulic properties of the complex aquifers and the structural and stratigraphic controls on groundwater movement aids in optimal storage and recovery of recharged water and provides information on the ability of aquifers shared by different water management agencies to fulfill competing storage and extraction demands. The movement of recharge water through the Niles Cone groundwater subbasin from Quarry Lakes and the possible hydraulic connection between the Niles Cone and the southern East Bay Plain groundwater subbasins were investigated using interferometric synthetic aperture radar (InSAR), water-chemistry, and isotopic data, including tritium/helium-3, helium-4, and carbon-14 age-dating techniques.InSAR data collected during refilling of the Quarry Lakes recharge ponds show corresponding ground-surface displacement. Maximum uplift was about 0.8 inches, reasonable for elastic expansion of sedimentary materials experiencing an increase in hydraulic head that resulted from pond refilling. Sodium concentrations increase while calcium and magnesium concentrations in groundwater decrease along groundwater flowpaths from the Niles Cone groundwater subbasin through the Deep aquifer to the northwest toward the southern East Bay Plain groundwater subbasin. Residual effects of pre-1970s intrusion of saline water from San Francisco Bay, including high chloride concentrations in groundwater, are evident in parts of the Niles Cone subbasin. Noble gas recharge temperatures indicate two primary recharge sources (Quarry Lakes and Alameda Creek) in the Niles Cone groundwater subbasin. Although recharge at Quarry Lakes affects hydraulic heads as far as the transition zone between the Niles Cone and East Bay Plain groundwater subbasins (about 5 miles), the effect of recharged water on water quality is only apparent in wells near (less than 2 miles) recharge sources. Groundwater chemistry from upper aquifer system wells near Quarry Lakes showed an evaporated signal (less negative oxygen and hydrogen isotopic values) relative to surrounding groundwater and a tritium concentration (2 tritium units) consistent with recently recharged water from a surface-water impoundment.Uncorrected carbon-14 activities measured in water sampled from wells in the Niles Cone groundwater subbasin range from 16 to 100 percent modern carbon (pmC). The geochemical reaction modeling software NETPATH was used to interpret carbon-14 ages along a flowpath from Quarry Lakes toward the East Bay Plain groundwater subbasin. Model results indicate that changes in groundwater chemistry are controlled by cation exchange on clay minerals and weathering of primary silicate minerals. Old groundwater (lower carbon-14 activities) is characterized by high dissolved silica and pH. Interpreted carbon-14 ages ranged from 830 to more than 7,000 years before present and are less than helium-4 ages that range from 2,000 to greater than 11,000 years before present. The average horizontal groundwater velocity along the studied flowpath, as calculated using interpreted carbon-14 ages, through the Deep aquifer of the Niles Cone groundwater subbasin is between 3 and 12 feet per year. The groundwater velocity decreases near the boundary of the transition zone to the southern East Bay Plain groundwater subbasin to about 0.5 feet per year. These changes may result from water recharged from different sources converging in flowpaths north of the transition zone, or a boundary to flow between the Niles Cone and southern East Bay Plain groundwater subbasins, likely owing to changes in lithology caused by depositional patterns.

40 CFR 63.543 - Standards for process sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the atmosphere from any existing, new, or reconstructed blast, reverberatory, rotary, or electric... discharge or cause to be discharged into the atmosphere from any existing, new, or reconstructed blast... atmosphere from any existing blast furnace any gases that contain total hydrocarbons in excess of 360 parts...

Studies on radon/thoron and their decay products in granite quarries around Bangalore city, India

NASA Astrophysics Data System (ADS)

Ningappa, C.; Sannappa, J.; Chandrashekara, M. S.; Paramesh, L.

2009-08-01

The radon survey was performed in granite quarries around Bangalore rural district and Bangalore city as part of a lung cancer epidemiological study. Long duration measurements of indoor and outdoor radon, thoron and their progenies concentrations were made around granite quarries of Bangalore rural district by using Solid State Nuclear Track Detector (SSNTD, LR-115, Type-II Plastic track detector) during summer and winter period (2006-07). The increase of radioactivity in granite quarries and inhalation dose to workers and populations near the quarries have been summarized. The higher concentrations of radon and thoron in granite quarries suggest radiation health effects on workers and public around the quarries is higher than permissible levels. The results are presented and analyzed with reference to ICRP limits.

Geomorphological records of diachronous quarrying activities along the ancient Appia route at the Aurunci Mountain pass (Central Italy)

NASA Astrophysics Data System (ADS)

Di Luzio, E.; Carfora, P.

2018-04-01

The topic of this research consists in the description of landscape modifications occurring from the 4th century BCE to the 19th century CE as a consequence of quarrying activities on carbonate slopes along a tract of the ancient Appia route crossing the central Apennine belt at the Aurunci Mountain pass (Lazio region, central Italy). The main objectives were to discern different quarrying phases and techniques, quantify quarrying activities and understand the role of quarrying in create morphological features. Multidisciplinary studies were completed including aerial photogrammetry, geoarchaeological field surveys, morphometric characterization of quarry areas, structural analysis of rock outcrops aided by terrestrial photogrammetry, GPS measurements. The results of this study show how the local geomorpological and tectonic setting determined which kinds of extractable rock material, i.e., rock blocks or breccias, were used for different purposes. Moreover, different phases of extraction were evidenced. A main Roman quarrying phase, lasting between the 4th century BCE and the 1st century CE, was recognized as taking place over eight quarry areas. These are delimited by sharp edges and have regular shapes, revealing in some cases a staircase-like morphological profile, and are characterized by similar volumes of extracted rock material. A later quarrying phase -the Bourbon Age, 19th century CE-is assumed to be evidenced instead by five quarries with a peculiar semi-elliptical shape and different volumes of carved material. Seven quarries were found to be of uncertain age. The quarry system described in this paper, together with geomorphological records of slope cuts, terraced surfaces, and the remains of retaining walls, represents a unique and important example of anthropogenic landscape modification in the territory of the central Apennines caused by the construction and maintenance of a Roman road over the centuries. This could be relevant for further studies on the relations between natural environments and the development of civilisation. In addition, the multi-methodological analyses of geomorphological records originated by quarrying activities may be considered for the characterization of similar quarry landscapes.

Testing the Reviewed Event Bulletin of the International Data Centre Using Waveform Cross Correlation: Repeat Events at Aitik Copper Mine, Sweden

NASA Astrophysics Data System (ADS)

Kitov, I. O.; Rozhkov, N.; Bobrov, D.; Rozhkov, M.; Yedlin, M. J.

2016-12-01

The quality of the Reviewed Event Bulletin (REB) issued by the International Data Centre (IDC) of the Comprehensive Nuclear-Test- Ban Treaty Organization (CTBTO) is crucial for the Member States as well as for the seismological community. One of the most efficient methods to test the REB quality is using repeat events having very accurate absolute locations. Hundreds of quarry blasts detonated at Aitik copper mine (the central point of active mining - 67.08N, 20.95E) were recorded by several seismic arrays of the International Monitoring System (IMS), found by IDC automatic processing and then confirmed by analysts as REB events. The size of the quarry is approximately 1 km and one can consider that the uncertainty in absolute coordinates of the studied events is less than 0.5 km as measured from the central point. In the REB, the corresponding epicenters are almost uniformly scattered over the territory 67.0N to 67.3N, and 20.7E to 21.5E. These REB locations are based on the measured arrival times as well as azimuth and slowness estimates at several IMS stations with the main input from ARCES, NOA, FINES, and HFS. The higher scattering of REB locations is caused by the uncertainty in measurements and velocity model. Seismological methods based on waveform cross correlation allow very accurate relative location of repeat events. Here we test the level of similarity between signals from these events. It was found that IMS primary array station ARCES demonstrates the highest similarity as expressed by cross correlation coefficient (CC) and signal-to-noise ratio (SNR) calculated at the CC traces. Small-aperture array FINES is the second best and large-aperture array NOA demonstrating mediocre performance likely due its size and the loss of coherency between high-frequency and relatively low-velocity signals from the mine. During the last five years station ARCES has been upgraded from a vertical array to a 3-C one. This transformation has improved the performance of CC-technique as applied to the Aitik mine events. We have also applied a Principal Component Analysis to estimate the level of variability in the signals as well as to build the best waveform template for effective detection and identification of all blasts conducted at Aitik mine.

78 FR 52943 - Changes in Flood Hazard Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-27

... 89015. North Carolina: Rowan Town of Granite The Honorable Mary Town Hall, 143 http:// October 17, 2013..... 370212 Quarry (12-04- S. Ponds, Mayor, North Salisbury www.ncfloodmaps.com/ 5555P). Town of Granite Avenue, Granite fhd.htm. Quarry, 143 North Quarry, NC 28072. Salisbury Avenue Granite Quarry, NC 28072...

New data towards the development of a comprehensive taphonomic framework for the Late Jurassic Cleveland-Lloyd Dinosaur Quarry, Central Utah

PubMed Central

Warnock, Jonathan P.; Eberhart, Shawn L.; Clawson, Steven R.; Noto, Christopher R.

2017-01-01

The Cleveland-Lloyd Dinosaur Quarry (CLDQ) is the densest deposit of Jurassic theropod dinosaurs discovered to date. Unlike typical Jurassic bone deposits, it is dominated by the presence of Allosaurus fragilis. Since excavation began in the 1920s, numerous hypotheses have been put forward to explain the taphonomy of CLDQ, including a predator trap, a drought assemblage, and a poison spring. In an effort to reconcile the various interpretations of the quarry and reach a consensus on the depositional history of CLDQ, new data is required to develop a robust taphonomic framework congruent with all available data. Here we present two new data sets that aid in the development of such a robust taphonomic framework for CLDQ. First, x-ray fluorescence of CLDQ sediments indicate elevated barite and sulfide minerals relative to other sediments from the Morrison Formation in the region, suggesting an ephemeral environment dominated by periods of hypereutrophic conditions during bone accumulation. Second, the degree of abrasion and hydraulic equivalency of small bone fragments dispersed throughout the matrix were analyzed from CLDQ. Results of these analyses suggest that bone fragments are autochthonous or parautochthonous and are derived from bones deposited in the assemblage rather than transported. The variability in abrasion exhibited by the fragments is most parsimoniously explained by local periodic re-working and re-deposition during seasonal fluctuations throughout the duration of the quarry assemblage. Collectively, these data support previous interpretations that the CLDQ represents an attritional assemblage in a poorly-drained overbank deposit where vertebrate remains were introduced post-mortem to an ephemeral pond during flood conditions. Furthermore, while the elevated heavy metals detected at the Cleveland-Lloyd Dinosaur Quarry are not likely the primary driver for the accumulation of carcasses, they are likely the result of multiple sources; some metals may be derived from post-depositional and diagenetic processes, and others are potentially produced from an abundance of decomposing vertebrate carcasses. These new data help to support the inferred depositional environment of the quarry as an ephemeral pond, and represent a significant step in understanding the taphonomy of the bonebed and Late Jurassic paleoecology in this region. PMID:28603668

Comparison of the occupational safety applications in marble quarries of Carrara (Italy) and Iscehisar (Turkey) by using Elmeri method.

PubMed

Ersoy, Metin; Yesilkaya, Liyaddin

2016-01-01

In this paper, a brief summary is given about marble quarries in Carrara (Italy) and Iscehisar (Turkey), the Elmeri method is introduced, work accidents that can happen in marble quarries and their causes besides work safety behaviours in fields are explained, and the Elmeri monitoring method is applied and analysed. For this reason, marble quarries are divided into seven in terms of working conditions and active six quarries both in Carrara and Iscehisar areas, and work safety behaviours are analysed. Analysis process is based on True-False method; there are 18 items in total under six main topics; three items on each topic. The safety index for each section and the main topics are also calculated. According to the calculated safety indexes, Carrara area marble quarries (65.08%) are safer than Iscehisar area marble quarries (46.01%).

40 CFR 421.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. PSNS Pollutant or... production Lead .000 .000 Zinc .000 .000 (b) Subpart G—Blast Furnace Wet Air Pollution Control. PSNS... pounds) of blast furnace lead bullion produced Lead .000 .000 Zinc .000 .000 (c) Subpart G—Blast Furnace...

40 CFR 421.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. PSNS Pollutant or... production Lead .000 .000 Zinc .000 .000 (b) Subpart G—Blast Furnace Wet Air Pollution Control. PSNS... pounds) of blast furnace lead bullion produced Lead .000 .000 Zinc .000 .000 (c) Subpart G—Blast Furnace...

Sedimentology, stratigraphy, and depositional environment of the Crystal Geyser Dinosaur Quarry, east-central Utah

USGS Publications Warehouse

Suarez, M.B.; Suarez, C.A.; Kirkland, J.I.; Gonzalez, Luis A.; Grandstaff, D.E.; Terry, D.O.

2007-01-01

The Crystal Geyser Dinosaur Quarry, near Green River, Utah, is located at the base of the Lower Cretaceous (Barremian) Yellow Cat Member of the Cedar Mountain Formation. The quarry preserves a nearly monospecific accumulation of a new basal therizinosauroid, Falcarius utahensis. We used field descriptions and petrographic analysis to determine the depositional environment and development of the quarry strata. Results of these analyses suggest that the quarry represents multiple episodes of bone accumulation buried by spring and overbank flood deposits. Evidence for these previously undescribed spring deposits includes calcite macroscopic structures within the quarry strata - such as pisolites and travertine fragments - and calcite micromorphologies - including radial-fibrous, feather, and scandulitic dendrite morphologies and tufa clasts. At least two episodes of bone incorporation are preserved in the quarry based on their stratigraphic position and lithologic associations. The unique depositional setting in and around the Crystal Geyser Dinosaur Quarry appears to have been favorable for the preservation of vertebrate fossils and provides insight into early Cretaceous environments in North America. Copyright ?? 2007, SEPM (Society for Sedimentary Geology).

Pump Hydro Energy Storage systems (PHES) in groundwater flooded quarries

NASA Astrophysics Data System (ADS)

Poulain, Angélique; de Dreuzy, Jean-Raynald; Goderniaux, Pascal

2018-04-01

Pump storage hydroelectricity is an efficient way to temporarily store energy. This technique requires to store temporarily a large volume of water in an upper reservoir, and to release it through turbines to the lower reservoir, to produce electricity. Recently, the idea of using old flooded quarries as a lower reservoir has been evoked. However, these flooded quarries are generally connected to unconfined aquifers. Consequently, pumping or injecting large volumes of water, within short time intervals, will have an impact on the adjacent aquifers. Conversely, water exchanges between the quarry and the aquifer may also influence the water level fluctuations in the lower reservoir. Using numerical modelling, this study investigates the interactions between generic flooded open pit quarries and adjacent unconfined aquifers, during various pump-storage cyclic stresses. The propagation of sinusoidal stresses in the adjacent porous media and the amplitude of water level fluctuations in the quarry are studied. Homogeneous rock media and the presence of fractures in the vicinity of the quarry are considered. Results show that hydrological quarry - rock interactions must be considered with caution, when implementing pump - storage systems. For rock media characterized by high hydraulic conductivity and porosity values, water volumes exchanges during cycles may affect significantly the amplitude of the water level fluctuations in the quarry, and as a consequence, the instantaneous electricity production. Regarding the impact of the pump - storage cyclic stresses on the surrounding environment, the distance of influence is potentially high under specific conditions, and is enhanced with the occurrence of rock heterogeneities, such as fractures. The impact around the quarry used as a lower reservoir thus appears as an important constraining factor regarding the feasibility of pump - storage systems, to be assessed carefully if groundwater level fluctuations around the quarry are expected to bring up adverse effects. Results highlight opportunities and challenges to be faced, to implement pump - storage hydroelectricity systems in old flooded open pit quarries.

BLAST: The Balloon-Borne Large Aperture Submillimeter Telescope

NASA Technical Reports Server (NTRS)

Devlin, Mark; Ade, Peter; Bock, Jamie; Dicker, Simon; Griffin, Matt; Gunderson, Josh; Halpern, Mark; Hargrave, Peter; Hughes, David; Klein, Jeff

2004-01-01

BLAST is the Balloon-borne Large-Aperture Sub-millimeter Telescope. It will fly from a Long Duration Balloon (LDB) platform from Antarctica. The telescope design incorporates a 2 m primary mirror with large-format bolometer arrays operating at 250, 350 and 500 microns. By providing the first sensitive large-area (10 sq. deg.) sub-mm surveys at these wavelengths, BLAST will address some of the most important galactic and cosmological questions regarding the formation and evolution of stars, galaxies and clusters. Galactic and extragalactic BLAST surveys will: (1) identify large numbers of high-redshift galaxies; (2) measure photometric redshifts, rest-frame FIR luminosities and star formation rates thereby constraining the evolutionary history of the galaxies that produce the FIR and sub-mm background; (3) measure cold pre-stellar sources associated with the earliest stages of star and planet formation; (4) make high-resolution maps of diffuse galactic emission over a wide range of galactic latitudes. In addition to achieving the above scientific goals, the exciting legacy of the BLAST LDB experiment will be a catalogue of 3000-5000 extragalactic sub-mm sources and a 100 sq. deg. sub-mm galactic plane survey. Multi-frequency follow-up observations from SIRTF, ASTRO-F, and Herschel, together with spectroscopic observations and sub-arcsecond imaging from ALMA are essential to understand the physical nature of the BLAST sources.

Improved Overpressure Recording and Modeling for Near-Surface Explosion Forensics

NASA Astrophysics Data System (ADS)

Kim, K.; Schnurr, J.; Garces, M. A.; Rodgers, A. J.

2017-12-01

The accurate recording and analysis of air-blast acoustic waveforms is a key component of the forensic analysis of explosive events. Smartphone apps can enhance traditional technologies by providing scalable, cost-effective ubiquitous sensor solutions for monitoring blasts, undeclared activities, and inaccessible facilities. During a series of near-surface chemical high explosive tests, iPhone 6's running the RedVox infrasound recorder app were co-located with high-fidelity Hyperion overpressure sensors, allowing for direct comparison of the resolution and frequency content of the devices. Data from the traditional sensors is used to characterize blast signatures and to determine relative iPhone microphone amplitude and phase responses. A Wiener filter based source deconvolution method is applied, using a parameterized source function estimated from traditional overpressure sensor data, to estimate system responses. In addition, progress on a new parameterized air-blast model is presented. The model is based on the analysis of a large set of overpressure waveforms from several surface explosion test series. An appropriate functional form with parameters determined empirically from modern air-blast and acoustic data will allow for better parameterization of signals and the improved characterization of explosive sources.

Simulated water budgets and ground-water/surface-water interactions in Bushkill and parts of Monocacy Creek watersheds, Northampton County, Pennsylvania: A preliminary study with identification of data needs

USGS Publications Warehouse

Risser, Dennis W.

2006-01-01

This report, prepared in cooperation with the Department of Environmental Protection, Office of Mineral Resources Management, provides a preliminary analysis of water budgets and generalized ground-water/surface-water interactions for Bushkill and parts of Monocacy Creek watersheds in Northampton County, Pa., by use of a ground-water flow model. Bushkill Creek watershed was selected for study because it has areas of rapid growth, ground-water withdrawals from a quarry, and proposed stream-channel modifications, all of which have the potential for altering ground-water budgets and the interaction between ground water and streams. Preliminary 2-dimensional, steady-state simulations of ground-water flow by the use of MODFLOW are presented to show the status of work through September 2005 and help guide ongoing data collection in Bushkill Creek watershed. Simulations were conducted for (1) predevelopment conditions, (2) a water table lowered for quarry operations, and (3) anthropogenic changes in hydraulic conductivity of the streambed and aquifer. Preliminary results indicated under predevelopment conditions, the divide between the Bushkill and Monocacy Creek ground-water basins may not have been coincident with the topographic divide and as much as 14 percent of the ground-water discharge to Bushkill Creek may have originated from recharge in the Monocacy Creek watershed. For simulated predevelopment conditions, Schoeneck Creek and parts of Monocacy Creek were dry, but Bushkill Creek was gaining throughout all reaches. Simulated lowering of the deepest quarry sump to an altitude of 147 feet for quarry operations caused ground-water recharge and streamflow leakage to be diverted to the quarry throughout about 14 square miles and caused reaches of Bushkill and Little Bushkill Creeks to change from gaining to losing streams. Lowering the deepest quarry sump to an altitude of 100 feet caused simulated ground-water discharge to the quarry to increase about 4 cubic feet per second. Raising the deepest sump to an altitude of 200 feet caused the simulated discharge to the quarry to decrease about 14 cubic feet per second.Decreasing the hydraulic conductivity of the streambed of Bushkill Creek in the reach of large losses of flow caused simulated ground-water levels to decline and ground-water discharge to a quarry to decrease from 74 to 45 cubic feet per second.Decreasing the hydraulic conductivity of a hypothesized highly transmissive zone with a plug of relatively impermeable material caused ground-water levels to increase east of the plug and decline west of the plug, and decreased the discharge to a quarry from 74 to 53 cubic feet per second. Preliminary results of the study have significant limitations, which need to be recognized by the user. The results demonstrated the usefulness of ground-water modeling with available data sets, but as more data become available through field studies, a more complete evaluation could be conducted of the preliminary assumptions in the conceptual model, model sensitivity, and effects of boundary conditions. Additional streamflow and ground-water-level measurements would be needed to better quantify recharge and aquifer properties, particularly the anisotropy of carbonate rocks. Measurements of streamflow losses at average, steady-state hydrologic conditions could provide a more accurate estimate of ground-water recharge from this source, which directly affects water budgets and contributing areas simulated by the model.

Quantification of non-ideal explosion violence with a shock tube

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jackson, Scott I; Hill, Larry G

There is significant interest in quantifying the blast violence associated with various nonideal explosions. Such data is essential to evaluate the damage potential of both explosive cookoff and terrorist explosive scenarios. We present a technique designed to measure the source energy associated with a non-ideal, asymmetrical, and three-dimensional explosion. A tube is used to confine and focus energy from a blast event into a one-dimensional, quasi-planar shock front. During propagation along the length of the tube, the wave is allowed to shocksteepen into a more ideal form. Pressure transducers then measure the shock overpressure as a function of the distancemore » from the source. One-dimensional blast scaling theory allows calculation of the source energy from this data. This small-scale test method addresses cost and noise concerns as well as boosting and symmetry issues associated with large-scale, three-dimensional, blast arena tests. Results from both ideal explosives and non-ideal explosives are discussed.« less

Air quality assessment on human well-being in the vicinity of quarry site

NASA Astrophysics Data System (ADS)

Ibrahim, W. H. W.; Marinie, E.; Yunus, J.; Asra, N.; Sukor, K. Mohd

2018-02-01

This study aims to investigate the variation of air pollutants associated with the quarry activities prior to classified distance from quarry site. Air pollutants were monitored with the use of instruments which are Rae System Multirae Lite Pumped (PGM-6208) to measure indoor air quality while TSI 8533 Dusttrack Drx Desktop Aerosol Monitor to measure outdoor air quality. Sampling will be replicated two times. The locations of quarry are at Bandar Saujana Putra and Taman Kajang Perdana 2, Selangor. The objectives of this study are to investigate the impact of quarry mining by preparing the suitable Indoor Air Quality Index and to prepare preventive measure for residential that caused from quarry mining activities. Both Qualitative and Quantitative approaches will be implemented in this study, which employed case study and interview survey. Both quarries identified previously will be the main case study. The Respondent’s interviews are from Local Authority and Quarry Management Staff while questionnaire surveys from selected residences. Measurement method will be used to measure the Particle Matter (PM2.5) for indoor and outdoor in selected resident’s area. However, this paper is primed to discuss the method used in this study. It is not only presents the beneficial information for future research on methodologies employed but also it is anticipated the benefit to environment which can increased residents’ well-being in the vicinity of quarry sites.

Limestone quarrying and quarry reclamation in Britain

NASA Astrophysics Data System (ADS)

Gunn, J.; Bailey, D.

1993-06-01

Limestones have been worked for many thousands of years — initially for building stone and agricultural lime and more recently for a wide range of construction and industrial uses. In most industrialized countries limestone quarries represent the most visually obvious and, in both process and landform terms, the most dramatic anthropogenic impact on karst terrain. However, quarrying has, to date, received surprisingly little attention from karst scientists. Research in the English Peak District suggested that the postexcavation evolution of quarried limestone rock faces was in part a result of the methods used in their excavation, and this led to the development of a technique designed to reduce the visual and environmental impacts of modern quarries by “Landform replication. ” This involves the use of controlled “restoration blasting” techniques on quarried rock slopes to construct a landform sequence similar to that in the surrounding natural landscape. The constructed landforms are then partially revegetated using appropriate wildflower, grass, and/or tree species.

Large scale germplasm screening for identification of novel rice blast resistance sources

PubMed Central

Vasudevan, Kumar; Vera Cruz, Casiana M.; Gruissem, Wilhelm; Bhullar, Navreet K.

2014-01-01

Rice is a major cereal crop that contributes significantly to global food security. Biotic stresses, including the rice blast fungus, cause severe yield losses that significantly impair rice production worldwide. The rapid genetic evolution of the fungus often overcomes the resistance conferred by major genes after a few years of intensive agricultural use. Therefore, resistance breeding requires continuous efforts of enriching the reservoir of resistance genes/alleles to effectively tackle the disease. Seed banks represent a rich stock of genetic diversity, however, they are still under-explored for identifying novel genes and/or their functional alleles. We conducted a large-scale screen for new rice blast resistance sources in 4246 geographically diverse rice accessions originating from 13 major rice-growing countries. The accessions were selected from a total collection of over 120,000 accessions based on their annotated rice blast resistance information in the International Rice Genebank. A two-step resistance screening protocol was used involving natural infection in a rice uniform blast nursery and subsequent artificial infections with five single rice blast isolates. The nursery-resistant accessions showed varied disease responses when infected with single isolates, suggesting the presence of diverse resistance genes/alleles in this accession collection. In addition, 289 accessions showed broad-spectrum resistance against all five single rice blast isolates. The selected resistant accessions were genotyped for the presence of the Pi2 resistance gene, thereby identifying potential accessions for isolation of allelic variants of this blast resistance gene. Together, the accession collection with broad spectrum and isolate specific blast resistance represent the core material for isolation of previously unknown blast resistance genes and/or their allelic variants that can be deployed in rice breeding programs. PMID:25324853

EXTERIOR OVERVIEW, LOOKING NORTH, OF THIS 400' DEEP LIMESTONE QUARRY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EXTERIOR OVERVIEW, LOOKING NORTH, OF THIS 400' DEEP LIMESTONE QUARRY PIT ('THE OLD PIT') WITH LEDGE PREPARED FOR LIMESTONE EXTRACTION. AN ELEVEN-HOLE SHOT WILL DISLODGE APPROXIMATELY 25,000 TONS OF LIMESTONE WHICH, AFTER LOADING AND CRUSHING, WILL BE USED FOR ROAD CONSTRUCTION. THE CALERA QUARRY IS ONE OF FOUR ACTIVE VULCAN MATERIALS COMPANY QUARRIES IN THE DISTRICT. VULCAN MATERIALS, A FORTUNE 500 FIRM, ESTABLISHED IN BIRMINGHAM IN 1906 AS BIRMINGHAM SLAG COMPANY, VULCAN MATERIALS IS THE NATION'S FOREMOST PRODUCER OF CONSTRUCTION AGGREGATE AND A LEADING CHEMICALS MANUFACTURER. - Vulcan Material Company, Calera Quarry, 1614 Highway 84, Calera, Shelby County, AL

EXTERIOR OVERVIEW, LOOKING NORTH, OF THIS 400' DEEP LIMESTONE QUARRY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EXTERIOR OVERVIEW, LOOKING NORTH, OF THIS 400' DEEP LIMESTONE QUARRY PIT ("THE OLD PIT") WITH LEDGE PREPARED FOR LIMESTONE EXTRACTION. AN ELEVEN-HOLE SHOT WILL DISLODGE APPROXIMATELY 25,000 TONS OF LIMESTONE WHICH, AFTER LOADING AND CRUSHING, WILL BE USED FOR ROAD CONSTRUCTION. THE CALERA QUARRY IS ONE OF FOUR ACTIVE VULCAN MATERIALS COMPANY QUARRIES IN THE DISTRICT. VULCAN MATERIALS, A FORTUNE 500 FIRM, ESTABLISHED IN BIRMINGHAM IN 1906 AS BIRMINGHAM SLAG COMPANY, VULCAN MATERIALS IS THE NATION'S FOREMOST PRODUCER OF CONSTRUCTION AGGREGATE AND A LEADING CHEMICALS MANUFACTURER - Vulcan Material Company, Calera Quarry, 1614 Highway 84, Calera, Shelby County, AL

A framework for emissions source apportionment in industrial areas: MM5/CALPUFF in a near-field application.

PubMed

Ghannam, K; El-Fadel, M

2013-02-01

This paper examines the relative source contribution to ground-level concentrations of carbon monoxide (CO), nitrogen dioxide (NO2), and PM10 (particulate matter with an aerodynamic diameter < 10 microm) in a coastal urban area due to emissions from an industrial complex with multiple stacks, quarrying activities, and a nearby highway. For this purpose, an inventory of CO, oxide of nitrogen (NO(x)), and PM10 emissions was coupled with the non-steady-state Mesoscale Model 5/California Puff Dispersion Modeling system to simulate individual source contributions under several spatial and temporal scales. As the contribution of a particular source to ground-level concentrations can be evaluated by simulating this single-source emissions or otherwise total emissions except that source, a set of emission sensitivity simulations was designed to examine if CALPUFF maintains a linear relationship between emission rates and predicted concentrations in cases where emitted plumes overlap and chemical transformations are simulated. Source apportionment revealed that ground-level releases (i.e., highway and quarries) extended over large areas dominated the contribution to exposure levels over elevated point sources, despite the fact that cumulative emissions from point sources are higher. Sensitivity analysis indicated that chemical transformations of NO(x) are insignificant, possibly due to short-range plume transport, with CALPUFF exhibiting a linear response to changes in emission rate. The current paper points to the significance of ground-level emissions in contributing to urban air pollution exposure and questions the viability of the prevailing paradigm of point-source emission reduction, especially that the incremental improvement in air quality associated with this common abatement strategy may not accomplish the desirable benefit in terms of lower exposure with costly emissions capping. The application of atmospheric dispersion models for source apportionment helps in identifying major contributors to regional air pollution. In industrial urban areas where multiple sources with different geometry contribute to emissions, ground-level releases extended over large areas such as roads and quarries often dominate the contribution to ground-level air pollution. Industrial emissions released at elevated stack heights may experience significant dilution, resulting in minor contribution to exposure at ground level. In such contexts, emission reduction, which is invariably the abatement strategy targeting industries at a significant investment in control equipment or process change, may result in minimal return on investment in terms of improvement in air quality at sensitive receptors.

Computational modeling of blast exposure associated with recoilless weapons combat training

NASA Astrophysics Data System (ADS)

Wiri, S.; Ritter, A. C.; Bailie, J. M.; Needham, C.; Duckworth, J. L.

2017-11-01

Military personnel are exposed to blast as part of routine combat training with shoulder-fired recoilless rifles. These weapons fire large-caliber ammunitions capable of disabling structures and uparmored vehicles (e.g., tanks). Scientific, medical, and military leaders are beginning to recognize the blast overpressure from these shoulder-fired weapons may result in acute and even long-term physiological effects to military personnel. However, the back blast generated from the Carl Gustav and Shoulder-launched Multipurpose Assault Weapon (SMAW) shoulder-fired weapons on the weapon operator has not been quantified. By quantifying and modeling the full-body blast exposure from these weapons, better injury correlations can be constructed. Blast exposure data from the Carl Gustav and SMAW were used to calibrate a propellant burn source term for computational simulations of blast exposure on operators of these shoulder-mounted weapon systems. A propellant burn model provided the source term for each weapon to capture blast effects. Blast data from personnel-mounted gauges during weapon firing were used to create initial, high-fidelity 3D computational fluid dynamic simulations using SHAMRC (Second-order Hydrodynamic Automatic Mesh Refinement Code). These models were then improved upon using data collected from static blast sensors positioned around the military personnel while weapons were utilized in actual combat training. The final simulation models for both the Carl Gustav and SMAW were in good agreement with the data collected from the personnel-mounted and static pressure gauges. Using the final simulation results, contour maps were created for peak overpressure and peak overpressure impulse experienced by military personnel firing the weapon as well as those assisting with firing of those weapons. Reconstruction of the full-body blast loading enables a more accurate assessment of the cause of potential mechanisms of injury due to air blast even for subjects not wearing blast gauges themselves. By accurately understanding the blast exposure and its variations across an individual, more meaningful correlations with physiologic response including potential TBI spectrum physiology associated with sub-concussive blast exposure can be established. As blast injury thresholds become better defined, results from these reconstructions can provide important insights into approaches for reducing possible risk of injury to personnel operating shoulder-launched weapons.

Atmospheric particulate emissions from dry abrasive blasting using coal slag.

PubMed

Kura, Bhaskar; Kambham, Kalpalatha; Sangameswaran, Sivaramakrishnan; Potana, Sandhya

2006-08-01

Coal slag is one of the widely used abrasives in dry abrasive blasting. Atmospheric emissions from this process include particulate matter (PM) and heavy metals, such as chromium, lead, manganese, nickel. Quantities and characteristics of PM emissions depend on abrasive characteristics and process parameters. Emission factors are key inputs to estimate emissions. Experiments were conducted to study the effect of blast pressure, abrasive feed rate, and initial surface contamination on total PM (TPM) emission factors for coal slag. Rusted and painted mild steel surfaces were used as base plates. Blasting was carried out in an enclosed chamber, and PM was collected from an exhaust duct using U.S. Environment Protection Agency source sampling methods for stationary sources. Results showed that there is significant effect of blast pressure, feed rate, and surface contamination on TPM emissions. Mathematical equations were developed to estimate emission factors in terms of mass of emissions per unit mass of abrasive used, as well as mass of emissions per unit of surface area cleaned. These equations will help industries in estimating PM emissions based on blast pressure and abrasive feed rate. In addition, emissions can be reduced by choosing optimum operating conditions.

Seismic and potential field studies over the East Midlands

NASA Astrophysics Data System (ADS)

Kirk, Wayne John

A seismic refraction profile was undertaken to investigate the source of an aeromagnetic anomaly located above the Widmerpool Gulf, East Midlands. Ten shots were fired into 51 stations at c. 1.5km spacing in a 70km profile during 41 days recording. The refraction data were processed using standard techniques to improve the data quality. A new filtering technique, known as Correlated Adaptive Noise Cancellation was tested on synthetic data and successfully applied to controlled source and quarry blast data. Study of strong motion data reveals that the previous method of site calibration is invalid. A new calibration technique, known as the Scaled Amplitude method is presented to provide safer charge size estimation. Raytrace modelling of the refraction data and two dimensional gravity interpretation confirms the presence of the Widmerpool Gulf but no support is found for the postulated intrusion. Two dimensional magnetic interpretation revealed that the aeromagnetic anomaly could be modelled with a Carboniferous igneous source. A Lower Palaeozoic refractor with a velocity of 6.0 km/s is identified at a maximum depth of c. 2.85km beneath the Widmerpool Gulf. Carboniferous and post-Carboniferous sediments within the gulf have velocities between 2.6-5.5 km/s with a strong vertical gradient. At the gulf margins, a refractor with a constant velocity of 5.2 km/s is identified as Dinantian limestone. A low velocity layer of proposed unaltered Lower Palaeozoics is identified beneath the limestone at the eastern edge of the Derbyshire Dome. The existence and areal extent of this layer are also determined from seismic reflection data. Image analysis of potential field data, presents a model identifying 3 structural provinces, the Midlands Microcraton, the Welsh and English Caledonides and a central region of complex linears. This model is used to explain the distribution of basement rocks determined from seismic and gravity profiles.

Tremors from earthquakes and blasting in the Powder River basin of Wyoming and Montana

USGS Publications Warehouse

Miller, C.H.; Osterwald, F.W.

1980-01-01

We are not aware of any damage to people or to property caused by blasting in the coal surface mines even though thousands of tons of explosives are detonated each year in the basin. The maximum weight of an individual explosive charge and the time interval between blasts are regulated so that any nearby structures will not be damaged or the residents disturbed. Blasting, nevertheless, does produce seismic tremors that can be recorded over 200 kilometers away. In addition, at one mine, some very low order aftershocks were recorded relatively close to the source within 2 hours after blasting.  

7 CFR 330.301 - Stone and quarry products from certain areas in Canada.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products...

Regularization of Instantaneous Frequency Attribute Computations

NASA Astrophysics Data System (ADS)

Yedlin, M. J.; Margrave, G. F.; Van Vorst, D. G.; Ben Horin, Y.

2014-12-01

We compare two different methods of computation of a temporally local frequency:1) A stabilized instantaneous frequency using the theory of the analytic signal.2) A temporally variant centroid (or dominant) frequency estimated from a time-frequency decomposition.The first method derives from Taner et al (1979) as modified by Fomel (2007) and utilizes the derivative of the instantaneous phase of the analytic signal. The second method computes the power centroid (Cohen, 1995) of the time-frequency spectrum, obtained using either the Gabor or Stockwell Transform. Common to both methods is the necessity of division by a diagonal matrix, which requires appropriate regularization.We modify Fomel's (2007) method by explicitly penalizing the roughness of the estimate. Following Farquharson and Oldenburg (2004), we employ both the L curve and GCV methods to obtain the smoothest model that fits the data in the L2 norm.Using synthetic data, quarry blast, earthquakes and the DPRK tests, our results suggest that the optimal method depends on the data. One of the main applications for this work is the discrimination between blast events and earthquakesFomel, Sergey. " Local seismic attributes." , Geophysics, 72.3 (2007): A29-A33.Cohen, Leon. " Time frequency analysis theory and applications." USA: Prentice Hall, (1995).Farquharson, Colin G., and Douglas W. Oldenburg. "A comparison of automatic techniques for estimating the regularization parameter in non-linear inverse problems." Geophysical Journal International 156.3 (2004): 411-425.Taner, M. Turhan, Fulton Koehler, and R. E. Sheriff. " Complex seismic trace analysis." Geophysics, 44.6 (1979): 1041-1063.

Cold blast furnace syndrome: a new source of toxic inhalation by nitrogen oxides.

PubMed

Tague, I; Llewellin, P; Burton, K; Buchan, R; Yates, D H

2004-05-01

To describe a new toxic inhalation syndrome in blast furnace workers. Fourteen workers developed acute respiratory symptoms shortly after exposure to "air blast" from blast furnace tuyeres. These included chest tightness, dyspnoea, rigors, and diaphoresis. Chest radiographs showed pulmonary infiltrates, and lung function a restrictive abnormality. This report includes a description of clinical features of the affected workers and elucidation of the probable cause of the outbreak. Clinical features and occupational hygiene measurements suggested the most likely cause was inhalation of nitrogen oxides at high pressure and temperature. While the task could not be eliminated, engineering controls were implemented to control the hazard. No further cases have occurred. "Cold blast furnace syndrome" represents a previously undescribed hazard of blast furnace work, probably due to inhalation of nitrogen oxides. It should be considered in the differential diagnosis of acute toxic inhalational injuries in blast furnace workers.

Sinkhole development induced by underground quarrying, and the related hazard

NASA Astrophysics Data System (ADS)

Parise, M.; Delle Rose, M.

2009-04-01

Sinkholes are extremely widespread in Apulia, a very flat and carbonate region, that acted as the foreland during the phases of building up of the Southern Apenninic Chain in Miocene time. This is due to the presence of soluble rocks throughout the region, that highly predispose the area to this very subtle natural hazard. In addition to the natural setting, which favours their development, sinkholes may also be induced by anthropogenic activities. In the latter sense, underground quarrying represents one of the most dangerous activities in karst areas. Apulia has a long history of quarrying. Since the roman time, the local rocks, from the Cretaceous micritic limestones to the Quaternary calcarenites, have been intensely quarried and used as building and ornamental materials. In several settings of the region, the rocks with the best petrographic characteristics are located at depths ranging from a few to some tens of meters. This caused the opening of many underground quarries, and the development of a complex network of subterranean galleries. Underground quarrying had a great impulse at the turn between the XIX and the XX century, when a large number of quarries was opened. Later on, after the Second World War, most of the quarries were progressively abandoned, even because of the first signs of instability, both underground and at the ground surface. With time, the memory of the presence and development of the underground quarries was progressively lost, with severe repercussions on the safety of the land above the excavated areas. Lack of knowledge of the subterranean pattern of galleries, combined with the expansion of the built-up areas at the surface, resulted in increasing significantly the vulnerability of exposed elements at risk. Events such as the 29 March, 2007, at Gallipoli only by chance did not result in any casualties, when a 15-mt wide and 5-mt deep sinkhole opened in a few hours at a road crossing, above the site of an old underground quarry. Within the framework of research programs devoted to recognition of sinkholes in Apulia, and addressed to the evaluation of the sinkhole hazard, this paper examines in detail the distribution of sinkholes related to underground quarrying in Salento, the southern part of Apulia, where the presence of subterranean quarries is particularly high. Through description of some case studies, the main problems related to underground quarries, and the development of sinkholes are discussed, even taking into account civil protection issues, that is in terms of the effects these phenomena may have on the local communities.

Deployment of the Oklahoma borehole seismic experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harben, P.E.; Rock, D.W.

1989-01-20

This paper discusses the Oklahoma borehole seismic experiment, currently in operation, set up by members of the Lawrence Livermore National Laboratory Treaty Verification Program and the Oklahoma Geophysical Observatory to determine deep-borehole seismic characteristics in geology typical of large regions in the Soviet Union. We evaluated and logged an existing 772-m deep borehole on the Observatory site by running caliper, cement bonding, casing inspection, and hole-deviation logs. Two Teledyne Geotech borehole-clamping seismometers were placed at various depths and spacings in the deep borehole. Currently, they are deployed at 727 and 730 m. A Teledyne Geotech shallow-borehole seismometer was mounted inmore » a 4.5-m hole, one meter from the deep borehole. The seismometers' system coherency were tested and found to be excellent to 35 Hz. We have recorded seismic noise, quarry blasts, regional earthquakes and teleseisms in the present configuration. We will begin a study of seismic noise and attenuation as a function of depth in the near future. 7 refs., 18 figs.« less

Doses from radon 222 irradiation for workers of the granite mining industry.

PubMed

Сrygorieva, L; Tomilin, Yu

2017-12-01

determining the integral value of annual effective dose from 222Rn for workers of the granite mining industry and assessment for the expected life effective dose from 222Rn. Materials were the results of measurements of external exposure dose of radiation measurements equiv alent equilibrium volume activity of 222Rn in workrooms and workplaces of major groups of granite quarry workers Mykolaiv region, studies EROA 222Rn air premises of these workers, research content 222Rn in drinking water. Granite quarry workers receive double radiation exposure of 222Rn due to exposure in the workplace and at home. The load in the workplace due to inhalation of 222Rn the air was (2.1 ± 0.2) mSv / year (vari ation 0.9-5.9) in a residential area - (4,1 ± 0,2) mSv/year (variation 1.8-5.9). The total annual effective dose from internal exposure from air flow and working premises and drinking water was on average (6,5 ± 0,2) mSv/year, equal to a maximum value of 20 mSv/year. The expected life for the chronic exposure dose of technological naturally occurring radioactive sources for people who work in the granite quarries and, while living in high risk from radon is in the range of 0.16-1.12 Sv. The research results indicate that in assessing the effects associated with exposure due to radon 222 contingents persons such surveys must take into account all sources of this radionuclide dose. L. Сrygorieva, Yu. Tomilin.

View of four large bore holes on top of quarry ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of four large bore holes on top of quarry wall, facing northeast - Granite Hill Plantation, Quarry No. 4, South side of State Route 16, 1.3 miles northeast east of Sparta, Sparta, Hancock County, GA

Examining lung cancer risks across different industries and occupations in Ontario, Canada: the establishment of the Occupational Disease Surveillance System.

PubMed

Jung, James K H; Feinstein, Saul G; Palma Lazgare, Luis; Macleod, Jill S; Arrandale, Victoria H; McLeod, Christopher B; Peter, Alice; Demers, Paul A

2018-05-07

The Occupational Disease Surveillance System (ODSS) was established in Ontario, Canada by linking a cohort of workers with data created from Workplace Safety and Insurance Board (WSIB) claims to administrative health databases. The aim of this study was to use ODSS to identify high-risk industry and occupation groups for lung cancer in Ontario. Workers in the WSIB lost time claims database were linked to the Ontario Cancer Registry using subjects' health insurance numbers, name, sex, birthdate and death date (if applicable). Several occupations and industries known to be at increased risk were outlined a priori to examine whether ODSS could replicate these associations. Age-adjusted, sex-stratified Cox proportional hazard models compared the risk of lung cancer within one industry/occupation versus all other groups in the cohort. Workers with a lung cancer diagnosis prior to cohort entry were excluded for analysis, leaving 2 187 762 workers for analysis. During the 1983 to 2014 follow-up, 34 661 workers in the cohort were diagnosed with lung cancer. Among expected high-risk industries, elevated risks were observed among workers in quarries/sand pits and construction industries for both sexes, and among males in metal mines, iron foundries, non-metallic mineral products industries and transportation industries. Excess risk was also observed among occupations in drilling/blasting, other mining/quarrying, mineral ore treating, excavating/grading/paving, truck driving, painting, bus driving and construction. This current surveillance system identified several established high-risk groups for lung cancer and could be used for ongoing surveillance of occupational lung cancer in Ontario. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Dynamic response analysis of surrounding rock under the continuous blasting seismic wave

NASA Astrophysics Data System (ADS)

Gao, P. F.; Zong, Q.; Xu, Y.; Fu, J.

2017-10-01

The blasting vibration that is caused by blasting excavation will generate a certain degree of negative effect on the stability of surrounding rock in underground engineering. A dynamic response analysis of surrounding rock under the continuous blasting seismic wave is carried out to optimize blasting parameters and guide underground engineering construction. Based on the theory of wavelet analysis, the reconstructed signals of each layer of different frequency bands are obtained by db8 wavelet decomposition. The difference of dynamic response of the continuous blasting seismic wave at a certain point caused by different blasting sources is discussed. The signal in the frequency band of natural frequency of the surrounding rock shows a certain degree of amplification effect deduced from the dynamic response characteristics of the surrounding rock under the influence of continuous blasting seismic wave. Continuous blasting operations in a fixed space will lead to the change of internal structure of the surrounding rock. It may result in the decline of natural frequency of the whole surrounding rock and it is also harmful for the stability of the surrounding rock.

INTERIOR VIEW, NORTH QUARRY, LOOKING NORTH TOWARDS THE SITE OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING NORTH TOWARDS THE SITE OF THE HISTORIC THOMAS FURNACES WITH ACTIVE DOLOMITE EXTRACTION ONGOING IN THE FOREGROUND. FURNACE FOUNDATION RUINS ARE PICTURED ON THE TOP LEDGE (CENTER LEFT) OF THE QUARRY. ALSO PICTURED IS THE HISTORIC THOMAS COKEWORKERS WITH (LEFT TO RIGHT) THE POWER PLANT, BOILER HOUSE, AND COKEWORKS. JUST SOUTH OF THE COKEWORKS, IS AN ACTIVE DOLOMITE CRUSHING, SIZING, AND SCREENING PLANT - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

INTERIOR VIEW, NORTH QUARRY, LOOKING NORTH TOWARDS THE SITE OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING NORTH TOWARDS THE SITE OF THE HISTORIC THOMAS FURNACES WITH ACTIVE DOLOMITE EXTRACTION ONGOING IN THE FOREGROUND. FURNACE FOUNDATION RUINS ARE PICTURED ON THE TOP LEDGE (CENTER LEFT) OF THE QUARRY. ALSO PICTURED IS THE HISTORIC THOMAS COKEWORKS WITH (LEFT TO RIGHT) THE POWER PLANT, BOILER HOUSE, AND COKEWORKS. JUST SOUTH OF THE COKEWORKS IS AN ACTIVE DOLOMITE CRUSHING, SIZING, AND SCREENING PLANT. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

Field evidence for control of quarrying by rock bridges in jointed bedrock

NASA Astrophysics Data System (ADS)

Hooyer, T. S.; Cohen, D. O.; Iverson, N. R.

2011-12-01

Quarrying is generally thought to be the most important mechanism by which glaciers erode bedrock. In quarrying models it is assumed that slow, subcritical, growth of pre-existing cracks rate-limits the process and occurs where there are large stress differences in the bed, such as near rock bumps where ice separates from the bed to form water-filled cavities. Owing to the direction of principal stresses in rocks associated with sliding and resultant cavity formation, models predict that quarrying will occur along cracks oriented perpendicular to the ice flow direction or parallel to zones of ice-bed contact. Preglacial cracks in rocks will tend to propagate mainly downward, and in sedimentary or some metamorphic rocks will merge with bedding planes, thereby helping to isolate rock blocks for dislodgement. In contrast to these model assumptions, new measurements of quarried surface orientations in the deglaciated forefield of nine glaciers in Switzerland and Canada indicate a strong correlation between orientations of pre-existing joints and quarried bedrock surfaces, independent of ice flow direction or ice-water contact lines. The strong correlation persists across all rock types, and rocks devoid of major joints lack quarried surfaces. We propose a new conceptual model of quarrying that idealizes the bedrock as a series of blocks separated by discontinuous preglacial joints containing intact rock bridges. Bridges concentrate stress differences caused by normal and shear forces acting at the rock surface. Failure of bridges is caused by slow subcritical crack growth enhanced by water pressure fluctuations. To lend credibility to this new model, we show field evidence of failed rock bridges in quarried surfaces and of rib marks on plumose structures that we interpret as arrest fracture fronts due to transient subglacial water-pressure fluctuations.

Internal ballistics of the detonation products of a blast-hole charge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mangush, S.K.; Garbunov, V.A.

1986-07-01

The authors investigate the gasdynamic flow of the detonation products of a blast-hole charge (the expansion of the detonation products in the blast hole and the gas outflow and propagation of shock airwaves into the face space). The problem is solved by means of a numerical program for integration of partial differential equations of one-dimensional gas-dynamics. A numerical model of the internal ballistics of a blast-hole charge is presented. In addition to the variation of the thermodynamic parameters in the blast hole, the formation of the shock wave in the face space is shown, which is the source of gasmore » ignition. Further development of the numerical model of the action of blast-hole charges is planned which will involve an analysis of a number of applied problems.« less

7 CFR 330.105 - Inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., DEPARTMENT OF AGRICULTURE FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY... products; soil; stone and quarry products under § 330.300; garbage; and any other product or article of any...; soil; stone or quarry products under § 330.300; garbage; or other products or articles which an...

7 CFR 330.105 - Inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., DEPARTMENT OF AGRICULTURE FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY... products; soil; stone and quarry products under § 330.300; garbage; and any other product or article of any...; soil; stone or quarry products under § 330.300; garbage; or other products or articles which an...

7 CFR 330.105 - Inspection.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., DEPARTMENT OF AGRICULTURE FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY... products; soil; stone and quarry products under § 330.300; garbage; and any other product or article of any...; soil; stone or quarry products under § 330.300; garbage; or other products or articles which an...

7 CFR 330.105 - Inspection.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., DEPARTMENT OF AGRICULTURE FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY... products; soil; stone and quarry products under § 330.300; garbage; and any other product or article of any...; soil; stone or quarry products under § 330.300; garbage; or other products or articles which an...

7 CFR 330.105 - Inspection.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., DEPARTMENT OF AGRICULTURE FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY... products; soil; stone and quarry products under § 330.300; garbage; and any other product or article of any...; soil; stone or quarry products under § 330.300; garbage; or other products or articles which an...

A Survey of Blast Injury across the Full Landscape of Military Science (Etude d’ensemble des blessures dues aux explosions a travers le panorama complet de la science militaire)

DTIC Science & Technology

2011-04-01

Military Science (RTO-MP-HFM-207) Executive Summary Blast injury is a significant source of casualties in current NATO operations. The term “blast...toxicologique du souffle incluant les mécanismes de dose (par exemple, normes d’exposition à un tube à choc ), la description des points limites dose

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON THE FIRST BENCH, POWDER HILLS ARE PRIMED FOR DOLOMITE EXTRACTION. ON THE SECOND BENCH, THE DRILL TEAM IS LAYING OUT THE NEXT SHOTS. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

Anciet marble quarries in Lesvos island Greece

NASA Astrophysics Data System (ADS)

Mataragkas, M.; Mataragkas, D.

2009-04-01

ANCIENT MARBLE QUARRIES IN LESBOS ISLAND, GREECE Varti- Matarangas M.1 & Matarangas D. 1 Institute of Geological and Mining Exploration (IGME), Olympic Village, Entrance C, ACHARNAE 13677, GREECE myrsini@igme.gr , myrsini@otenet.g r A B S T R A C T Ten ancient marble quarries of Lesbos Island, most of them previously unknown, have been studied, in the frame of the research study on the ancient marble quarries in the Aegean Sea. In the present paper the geological, petrological and morphological features of the aforementioned quarries are examined. Concerning the six ancient quarries located in the areas of Tarti, Agia Paraskevi (Tsaf), Mageiras, Loutra, Latomi (Plomari) and Thermi, the authochthonous neopaleozoic unit constitutes their geological formation, while their hosting lithological formations are the included crystalline limestone lens like beds. In two ancient quarries in the areas Moria and Alyfanta, the geological formation is the authochthonous upper Triassic series and the hosting lithological formation the upper Triassic carbonate sequence, while in the areas of Akrasi-Abeliko and Karyni, the geological formation is the thrust Triassic unit and the lithological hosting formations are the included strongly deformed or not crystalline limestone lenticular beds. Furthermore, the petrographic features were also determined permitting the identification of the building stones that have been used.

Lung function impact from working in the pre-revolution Libyan quarry industry.

PubMed

Draid, Marwan M; Ben-Elhaj, Khaled M; Ali, Ashraf M; Schmid, Kendra K; Gibbs, Shawn G

2015-05-07

The purpose of this study was to determine the lung impact from working within the Libyan quarry industry, and if the length of work impacted the degree of degradation. Eighty three workers from eight silica quarries in the Nafusa Mountains of Libya opted to participate. These quarries were working the upper cretaceous geological structure. Eighty-five individuals who lived in Gharyan City with no affiliation to quarry operations participated as controls. Spirometry variables evaluated were Forced Vital Capacity (FVC), Forced Expiratory Volume at 1.0 second (FEV1), FVC/FEV1 and Peak Expiratory Flow (PEF). Control and exposed groups had no differences in terms of height, weight, or smoking status (p = 0.18, 0.20, 0.98, respectively). Prior to adjustment for other variables, FVC, FEV1, and PEF are all significantly lower in the exposed group (p = 0.003, 0.009, 0.03, respectively). After adjustment for age, height, weight, and smoking status, there remain significant differences between the control and exposed groups for FVC, FEV1, and PEF. This analysis demonstrated that exposure to quarry dust has a detrimental effect on lung function, and that pre-revolution Libyan quarry workers were being exposed. This study shows that any exposure is harmful, as the reduction in lung function was not significantly associated with years of exposure.

Dispersal of arbuscular mycorrhizal fungi and plants during succession

NASA Astrophysics Data System (ADS)

García de León, David; Moora, Mari; Öpik, Maarja; Jairus, Teele; Neuenkamp, Lena; Vasar, Martti; Bueno, C. Guillermo; Gerz, Maret; Davison, John; Zobel, Martin

2016-11-01

Arbuscular mycorrhizal (AM) fungi are important root symbionts that enhance plant nutrient uptake and tolerance to pathogens and drought. While the role of plant dispersal in shaping successional vegetation is well studied, there is very little information about the dispersal abilities of AM fungi. We conducted a trap-box experiment in a recently abandoned quarry at 10 different distances from the quarry edge (i.e. the potential propagule source) over eleven months to assess the short term, within-year, arrival of plant and AM fungal assemblages and hence their dispersal abilities. Using DNA based techniques we identified AM fungal taxa and analyzed their phylogenetic diversity. Plant diversity was determined by transporting trap soil to a greenhouse and identifying emerging seedlings. We recorded 30 AM fungal taxa. These contained a high proportion of ruderal AM fungi (30% of taxa, 79% of sequences) but the richness and abundance of AM fungi were not related to the distance from the presumed propagule source. The number of sequences of AM fungi decreased over time. Twenty seven plant species (30% of them ruderal) were recorded from the soil seed traps. Plant diversity decreased with distance from the propagule source and increased over time. Our data show that AM fungi with ruderal traits can be fast colonizers of early successional habitats.

Blast-wave density measurements

NASA Astrophysics Data System (ADS)

Ritzel, D. V.

Applications of a densitometer to obtain time-resolved data on the total density in blast-wave flows are described. A beta-source (promethium-147) is separated by a gap from a scintillator and a photomultiplier tube (PMT). Attenuation of the radiation beam by the passing blast wave is due to the total density in the gap volume during the wave passage. Signal conditioning and filtering methods permit the system to output linearized data. Results are provided from use of the system to monitor blast waves emitted by detonation of a 10.7 m diameter fiberglass sphere containing 609 tons of ammonium nitrate/fuel oil at a 50.6 m height. Blast wave density data are provided for peak overpressure levels of 245, 172 and 70 kPa and distances of 183, 201 and 314 m from ground zero. Data resolution was of high enough quality to encourage efforts to discriminate dust and gasdynamic phenomena within passing blast waves.

Cold blast furnace syndrome: a new source of toxic inhalation by nitrogen oxides

PubMed Central

Tague, I; Llewellin, P; Burton, K; Buchan, R; Yates, D

2004-01-01

Methods: Fourteen workers developed acute respiratory symptoms shortly after exposure to "air blast" from blast furnace tuyeres. These included chest tightness, dyspnoea, rigors, and diaphoresis. Chest radiographs showed pulmonary infiltrates, and lung function a restrictive abnormality. This report includes a description of clinical features of the affected workers and elucidation of the probable cause of the outbreak. Results: Clinical features and occupational hygiene measurements suggested the most likely cause was inhalation of nitrogen oxides at high pressure and temperature. While the task could not be eliminated, engineering controls were implemented to control the hazard. No further cases have occurred. Conclusions: "Cold blast furnace syndrome" represents a previously undescribed hazard of blast furnace work, probably due to inhalation of nitrogen oxides. It should be considered in the differential diagnosis of acute toxic inhalational injuries in blast furnace workers. PMID:15090669

Specification aggregate quarry expansion: a case study demonstrating sustainable management of natural aggregate resources

USGS Publications Warehouse

Langer, William H.; Tucker, M.L.

2003-01-01

Many countries, provinces, territories, or states in the European Union, Australia, Canada, the United States, and elsewhere have begun implementing sustainability programs, but most of those programs stop short of sustainable management of aggregate resources. Sustainable practices do not always have to be conducted under the title of sustainability. This case study describes how Lafarge, a large multinational construction materials supplier, implemented the principles of sustainability even though there was an absence of existing local government policies or procedures addressing sustainable resource management. Jefferson County, Colorado, USA, is one of three counties in the six-county Denver, Colorado, region that has potentially available sources of crushed stone. Crushed stone comprises 30 percent of the aggregate produced in the area and plays a major role in regional aggregate resource needs. Jefferson County is home to four of the five crushed stone operations in the Denver region. Lafarge operates one of those four quarries. Lafarge recently proposed to expand its reserves by exchanging company-owned land for existing dedicated open space land adjacent to their quarry but owned by Jefferson County. A similar proposal submitted about 10 years earlier had been denied. Contrary to the earlier proposal, which was predicated on public relations, the new proposal was predicated on public trust. Although not explicitly managed under the moniker of sustainability, Lafarge used basic management principles that embody the tenets of sustainability. To achieve the goals of sustainable aggregate management where no governmental policies existed, Lafarge not only assumed their role of being a responsible corporate and environmental member of the community, but also assumed the role of facilitator to encourage and enable other stakeholders to responsibly resolve legitimate concerns regarding the Lafarge quarry proposal. Lafarge successfully presented an enlightened proposal where the county will gain 745 acres of new open space land in exchange for 60 acres of current open space land adjacent to the quarry. The process involved collaborative efforts by all stakeholders and resulted in an outcome that balances the needs of society, the environment, and business.

Single-subject-based whole-brain MEG slow-wave imaging approach for detecting abnormality in patients with mild traumatic brain injury

PubMed Central

Huang, Ming-Xiong; Nichols, Sharon; Baker, Dewleen G.; Robb, Ashley; Angeles, Annemarie; Yurgil, Kate A.; Drake, Angela; Levy, Michael; Song, Tao; McLay, Robert; Theilmann, Rebecca J.; Diwakar, Mithun; Risbrough, Victoria B.; Ji, Zhengwei; Huang, Charles W.; Chang, Douglas G.; Harrington, Deborah L.; Muzzatti, Laura; Canive, Jose M.; Christopher Edgar, J.; Chen, Yu-Han; Lee, Roland R.

2014-01-01

Traumatic brain injury (TBI) is a leading cause of sustained impairment in military and civilian populations. However, mild TBI (mTBI) can be difficult to detect using conventional MRI or CT. Injured brain tissues in mTBI patients generate abnormal slow-waves (1–4 Hz) that can be measured and localized by resting-state magnetoencephalography (MEG). In this study, we develop a voxel-based whole-brain MEG slow-wave imaging approach for detecting abnormality in patients with mTBI on a single-subject basis. A normative database of resting-state MEG source magnitude images (1–4 Hz) from 79 healthy control subjects was established for all brain voxels. The high-resolution MEG source magnitude images were obtained by our recent Fast-VESTAL method. In 84 mTBI patients with persistent post-concussive symptoms (36 from blasts, and 48 from non-blast causes), our method detected abnormalities at the positive detection rates of 84.5%, 86.1%, and 83.3% for the combined (blast-induced plus with non-blast causes), blast, and non-blast mTBI groups, respectively. We found that prefrontal, posterior parietal, inferior temporal, hippocampus, and cerebella areas were particularly vulnerable to head trauma. The result also showed that MEG slow-wave generation in prefrontal areas positively correlated with personality change, trouble concentrating, affective lability, and depression symptoms. Discussion is provided regarding the neuronal mechanisms of MEG slow-wave generation due to deafferentation caused by axonal injury and/or blockages/limitations of cholinergic transmission in TBI. This study provides an effective way for using MEG slow-wave source imaging to localize affected areas and supports MEG as a tool for assisting the diagnosis of mTBI. PMID:25009772

Off-center blast in a shocked medium

NASA Astrophysics Data System (ADS)

Duncan-Miller, G. C.; Stone, W. D.

2018-07-01

When multiple blasts occur at different times, the situation arises in which a blast wave is propagating into a medium that has already been shocked. Determining the evolution in the shape of the second shock is not trivial, as it is propagating into air that is not only non-uniform, but also non-stationary. To accomplish this task, we employ the method of Kompaneets to determine the shape of a shock in a non-uniform media. We also draw from the work of Korycansky (Astrophys J 398:184-189. https://doi.org/10.1086/171847 , 1992) on an off-center explosion in a medium with radially varying density. Extending this to treat non-stationary flow, and making use of approximations to the Sedov solution for the point blast problem, we are able to determine an analytic expression for the evolving shape of the second shock. In particular, we consider the case of a shock in air at standard ambient temperature and pressure, with the second shock occurring shortly after the original blast wave reaches it, as in a sympathetic detonation.

Geometry of surface fractures along the Mervine Anticline in Kay County, north central Oklahoma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hobbs, R.D.; Cemen, I.; Rizer, W.D.

1993-02-01

Surface fractures in the Lower Permian Barneston Formation are well exposed at three quarries in Kay County, north central Oklahoma. The three quarries are located along the Mervine Anticline which is a broad, assymmetric, low amplitude drape-like fold over a N20E trending sub-surface fault. The most northerly of the three quarries is at the axial surface trace of the anticline. The second quarry is one mile to the west and the third quarry is one-quarter mile to the east of the axial surface trace. In each quarry, a representative area of about 7,850 square feet was chosen for detailed mappingmore » of the surface fractures. In each representative area, the authors divided the surface fractures into what they termed as primary' and secondary' fractures. Traverse and area sampling methods were used to collect quantitative data on the joint orientation and frequency. The primary fractures are orthogonal and have a visible opening, while the secondary fractures have little or no opening. The primary fractures, the orthogonal sets, strike N30W and N75E. The secondary fractures show a slight preferred orientation along N65E although the overall distribution is random. These observations suggest that a similar fracture geometry exists in all three quarries. However, in one quarry the authors observed that fracture surfaces of the N30W striking set are inclined and their formation may have been influenced by movement along the proposed subsurface fault in the area.« less

Evaluation of Cross-Correlation Methods on a Massive Scale for Accurate Relocation of Seismic Events in East Asia

DTIC Science & Technology

2006-04-21

purposes, such as scientific study of earthquake interactions in a fault zone or seismic sources associated with magma conduits in a volcano , relative... Kilauea , J. Geophys. Res., 99, 375-393. HARRIS, D.B. (1991), A waveform correlation method for identifying quarry explosions, Bull. Seismol. Soc. Am

77 FR 12004 - Stanislaus National Forest, CA; Notice of Intent To Prepare an Environmental Impact Statement for...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-28

... Prepare an Environmental Impact Statement for Candy Rock Quarry Management AGENCY: Forest Service, USDA... Forest proposes to set permanent limitations on recreational target shooting at Candy Rock Quarry near... an appropriate activity at Candy Rock Quarry in the context of safety, public health, and applicable...

77 FR 14426 - Petitions for Modification of Application of Existing Mandatory Safety Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-09

... Granite Company, LLC, 369 North State Street, Concord, New Hampshire 03301. Mine: Swenson Granite gray... Swenson Granite Gray Quarry is an open dimensional granite quarry operating fixed stiffleg derricks to... granite product if it can not be seen. (6) The quarry employees direct all derrick moves and positioning...

Analysis of the Mobilization of Debris Flows

DTIC Science & Technology

1974-10-01

31 17 . Debris-flow source area at Roofing Granule Quarry, San Bernardino County, California 39 18. Debris-flow source area at Roofing Granule...down a channel about 12 to 16 cm wide with a 35 degree slope. Water, oozing out of the landslide mass into 17 wmmaaaamam’j ■ma the debris channel...marble used as roofing granules (Fig. 17 ) 2 1/2 km north of the town of Wrightwood, about 65 km north- * east of Los Angeles, California (Fig. 1

12. Photographic copy of photograph. (Source: U.S. Department of Interior. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. Photographic copy of photograph. (Source: U.S. Department of Interior. Office of Indian Affairs. Indian Irrigation Service. Annual Report, Fiscal Year 1925. Vol. I, Narrative and Photographs, Irrigation District #4, California and Southern Arizona, RG 75, Entry 655, Box 28, National Archives, Washington, DC.) Photographer unknown. SACATON DAM AND BRIDGE FROM QUARRY HILL, PRACTICALLY COMPLETED, 6/18/25 - San Carlos Irrigation Project, Sacaton Dam & Bridge, Gila River, T4S R6E S12/13, Coolidge, Pinal County, AZ

11. Photographic copy of photograph. (Source: U.S. Department of Interior. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Photographic copy of photograph. (Source: U.S. Department of Interior. Office of Indian Affairs. Indian Irrigation Service. Annual Report, Fiscal Year 1925. Vol. I, Narrative and Photographs, Irrigation District #4, California and Southern Arizona, RG 75, Entry 655, Box 28, National Archives, Washington, DC.) Photographer unknown. SACATON DAM AND BRIDGE SITE FROM QUARRY HILL, 10/1/24 - San Carlos Irrigation Project, Sacaton Dam & Bridge, Gila River, T4S R6E S12/13, Coolidge, Pinal County, AZ

Strength Characteristics of Quarry Dust in Replacement of Sand

NASA Astrophysics Data System (ADS)

Shyam Prakash, K.; Hanumantha Rao, Ch, Dr

2017-08-01

The replacement of natural fine aggregate by using quarry dust leads to consumption of generated quarry dust, the requirement of land fill area can be reduced and solves the natural sand scarcity problem. The sand availability as a fine aggregate at low cost which needs the reason to search as a alternative material. Even it causes saddle to dump the crusher dust at one place which causes environmental pollution. The chemical analysis, specific gravity, sieve analysis and compressive strength is identified for various percentage and grades of concrete by replacement of sand with quarry dust.

Lung Function Impact from Working in the Pre-Revolution Libyan Quarry Industry

PubMed Central

Draid, Marwan M.; Ben-Elhaj, Khaled M.; Ali, Ashraf M.; Schmid, Kendra K.; Gibbs, Shawn G.

2015-01-01

The purpose of this study was to determine the lung impact from working within the Libyan quarry industry, and if the length of work impacted the degree of degradation. Eighty three workers from eight silica quarries in the Nafusa Mountains of Libya opted to participate. These quarries were working the upper cretaceous geological structure. Eighty-five individuals who lived in Gharyan City with no affiliation to quarry operations participated as controls. Spirometry variables evaluated were Forced Vital Capacity (FVC), Forced Expiratory Volume at 1.0 second (FEV1), FVC/FEV1 and Peak Expiratory Flow (PEF). Control and exposed groups had no differences in terms of height, weight, or smoking status (p = 0.18, 0.20, 0.98, respectively). Prior to adjustment for other variables, FVC, FEV1, and PEF are all significantly lower in the exposed group (p = 0.003, 0.009, 0.03, respectively). After adjustment for age, height, weight, and smoking status, there remain significant differences between the control and exposed groups for FVC, FEV1, and PEF. This analysis demonstrated that exposure to quarry dust has a detrimental effect on lung function, and that pre-revolution Libyan quarry workers were being exposed. This study shows that any exposure is harmful, as the reduction in lung function was not significantly associated with years of exposure. PMID:25961801

30 CFR 56.6405 - Firing devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Explosives Electric Blasting § 56... all electric detonators to be fired with the type of circuits used. Storage or dry cell batteries are not permitted as power sources. (b) Blasting machines shall be tested, repaired, and maintained in...

40 CFR 63.543 - Standards for process sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (a) No owner or operator of a secondary lead smelter shall discharge or cause to be discharged into the atmosphere from any existing, new, or reconstructed blast, reverberatory, rotary, or electric... discharge or cause to be discharged into the atmosphere from any existing, new, or reconstructed blast...

The characterization and evaluation of accidental explosions

NASA Technical Reports Server (NTRS)

Strehlow, R. A.; Baker, W. E.

1975-01-01

Accidental explosions are discussed from a number of viewpoints. First, all accidental explosions, intentional explosions and natural explosions are characterized by type. Second, the nature of the blast wave produced by an ideal (point source or HE) explosion is discussed to form a basis for describing how other explosion processes yield deviations from ideal blast wave behavior. The current status blast damage mechanism evaluation is also discussed. Third, the current status of our understanding of each different category of accidental explosions is discussed in some detail.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The Weldon Spring Quarry is one of two noncontiguous areas that constitute the US Department of Energy`s (DOE) Weldon Spring site. The main area of the site is the chemical plant. Both areas are located in St. Charles County, Missouri, about 48 km (30 mi) west of St. Louis. The US Environmental Protection Agency (EPA) listed the quarry on the National Priorities List (NPL) in 1987, and the chemical plant area was added to the list in 1989. The quarry is about 6.4 km (4 mi) south-southwest of the chemical plant area; it is accessible from State Route 94 andmore » is currently fenced and closed to the public. The quarry is approximately 300 m (1,000 ft) long by 140 m (450 ft) wide and covers an area of approximately 3.6 ha (9 acres). The quarry was used by the Army for disposal of chemically contaminated (explosive) materials in the 1940s and was later used for the disposal of radioactively contaminated material by the Atomic Energy Commission (AEC) in the 1960s. Approximately 110,000 m{sup 3} (144,000 yd{sup 3}) of soil and waste material was removed from the quarry and transported to the chemical plant area as part of completing the remedial action stipulated in the Record of Decision (ROD) for the Quarry Bulk Waste Operable Unit (DOE 1990). Bulk waste removal was completed in October 1995. These wastes have been placed in the disposal cell at the chemical plant. Prior to bulk waste removal, contaminated water contained in the quarry pond was also removed; approximately 170 million liters (44 million gal) have been treated as of March 1998.« less

Respiratory symptoms and ventilatory functions among quarry workers in Edo state, Nigeria

PubMed Central

Isara, Alphonsus Rukevwe; Adam, Vincent Yakubu; Aigbokhaode, Adesuwa Queen; Alenoghena, Innocent Osi

2016-01-01

Introduction Workers in the quarry industries are exposed to hazards resulting from the inhalation of air borne particulates. The study determined the prevalence of respiratory symptoms and assessed ventilatory functions among quarry workers in Edo state, Nigeria. Methods Quarry workers (site workers and office workers) were interviewed using structured questionnaire. FEV1, FVC, FEV1/FVC and PEFR were measured using a KoKo Legend spirometer. Results A total of 113 quarry workers (76 exposure and 37 controls) were studied. The exposure group had significantly higher occurrence of chest tightness (35.5%) compared with 16.2% of the controls (p < 0.05). The occurrence of cough (23.7% versus 13.5%), sputum (21.1% versus 16.2%), and dyspnoea (7.9% versus 5.4%), were higher in exposure groups while wheeze (10.8% versus 10.5%) and nasal congestion (27.0% and 25.0%) were higher in the control groups. The mean (SD) FEV1, and FVC were significantly lower among the exposure compared with the control group; 2.77L (0.73) versus 3.14L (0.78), p < 0.05, and 3.48L (0.84) versus 3.89L (0.92), p < 0.05. In both groups, smokers had significantly lower mean (SD) FEV1, FVC and PEFR compared with non-smokers; 2.91L (0.77) versus 3.39L (0.69), p = 0.01, 3.61L (0.91) versus 4.26L (0.74), p < 0.05 and 6.56L (2.43) versus 7.98L (1.67), p < 0.05. Conclusion Chronic exposure to quarry dust is associated with respiratory symptoms and reduced lung function indices among quarry workers. The enforcement of the use of PPEs and periodic evaluation the lung function status of quarry workers is advocated. PMID:27347301

Respiratory symptoms and ventilatory functions among quarry workers in Edo state, Nigeria.

PubMed

Isara, Alphonsus Rukevwe; Adam, Vincent Yakubu; Aigbokhaode, Adesuwa Queen; Alenoghena, Innocent Osi

2016-01-01

Workers in the quarry industries are exposed to hazards resulting from the inhalation of air borne particulates. The study determined the prevalence of respiratory symptoms and assessed ventilatory functions among quarry workers in Edo state, Nigeria. Quarry workers (site workers and office workers) were interviewed using structured questionnaire. FEV1, FVC, FEV1/FVC and PEFR were measured using a KoKo Legend spirometer. A total of 113 quarry workers (76 exposure and 37 controls) were studied. The exposure group had significantly higher occurrence of chest tightness (35.5%) compared with 16.2% of the controls (p < 0.05). The occurrence of cough (23.7% versus 13.5%), sputum (21.1% versus 16.2%), and dyspnoea (7.9% versus 5.4%), were higher in exposure groups while wheeze (10.8% versus 10.5%) and nasal congestion (27.0% and 25.0%) were higher in the control groups. The mean (SD) FEV1, and FVC were significantly lower among the exposure compared with the control group; 2.77L (0.73) versus 3.14L (0.78), p < 0.05, and 3.48L (0.84) versus 3.89L (0.92), p < 0.05. In both groups, smokers had significantly lower mean (SD) FEV1, FVC and PEFR compared with non-smokers; 2.91L (0.77) versus 3.39L (0.69), p = 0.01, 3.61L (0.91) versus 4.26L (0.74), p < 0.05 and 6.56L (2.43) versus 7.98L (1.67), p < 0.05. Chronic exposure to quarry dust is associated with respiratory symptoms and reduced lung function indices among quarry workers. The enforcement of the use of PPEs and periodic evaluation the lung function status of quarry workers is advocated.

Neck blast disease influences grain yield and quality traits of aromatic rice.

PubMed

Khan, Mohammad Ashik Iqbal; Bhuiyan, Md Rejwan; Hossain, Md Shahadat; Sen, Partha Pratim; Ara, Anjuman; Siddique, Md Abubakar; Ali, Md Ansar

2014-11-01

A critical investigation was conducted to find out the effect of neck blast disease on yield-contributing characters, and seed quality traits of aromatic rice in Bangladesh. Both healthy and neck-blast-infected panicles of three aromatic rice cultivars (high-yielding and local) were collected and investigated at Plant Pathology Division, Bangladesh Rice Research Institute (BRRI), Gazipur, Bangladesh. All of the tested varieties were highly susceptible to neck blast disease under natural conditions, though no leaf blast symptoms appear on leaves. Neck blast disease increased grain sterility percentages, reduced grain size, yield and quality traits of seeds. The degrees of yield and seed quality reduction depended on disease severity and variety's genetic make-up. Unfilled grains were the main source of seed-borne pathogen, especially for blast in the seed lot. Transmission of blast pathogen from neck (panicle base) to seed was very poor. These findings are important, especially concerning the seed certification programme in which seed lots are certified on the basis of field inspection. Finally, controlled experiments are needed to draw more critical conclusions. Copyright © 2014 Académie des sciences. Published by Elsevier SAS. All rights reserved.

Comparison of physical and mechanical properties of river sand concrete with quarry dust concrete

NASA Astrophysics Data System (ADS)

Opara, Hyginus E.; Eziefula, Uchechi G.; Eziefula, Bennett I.

2018-03-01

This study compared the physical and mechanical properties of river sand concrete with quarry dust concrete. The constituent materials were batched by weight. The water-cement ratio and mix ratio selected for the experimental investigation were 0.55 and 1:2:4, respectively. The specimens were cured for 7, 14, 21 and 28 days. Slump, density and compressive strength tests were carried out. The results showed that river sand concrete had greater density and compressive strength than quarry dust concrete for all curing ages. At 28 days of curing, river sand concrete exceeded the target compressive strength by 36%, whereas quarry dust concrete was less than the target compressive strength by 12%. Both river sand concrete and quarry dust concrete for the selected water/cement ratio and mix ratio are suitable for non-structural applications and lightly-loaded members where high strength is not a prerequisite.

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4) Dross furnace charging location; (5) Blast furnace and dross furnace tapping location; (6) Sinter machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) The...

Candoglia Marble and the "Veneranda Fabbrica del Duomo di Milano": a resource for Global Heritage Stone Designation in the Italian Alps

NASA Astrophysics Data System (ADS)

Borghi, Alessandro; Castelli, Daniele; Corbetta, Elio; Antonella Dino, Giovanna

2015-04-01

Alpine marbles have been widely used in the past for celebrated, both indoor and outdoor, applications. Among them, the Candoglia Marble, a worldwide known and appreciated georesource, and its "bastard brother" from the nearby Ornavasso area were and are exploited in the Verbano-Cusio-Ossola quarry basin of Northwestern Italian Alps. They crop out as lenses (up to 30 m in thickness) interlayered within high-grade paragneisses of the Ivrea Zone, a section of deep continental crust that experienced amphibolite- to granulite-facies metamorphism of Palaeozoic age. The Candoglia and Ornavasso Marbles are pinkish to greyish, coarse-grained (> 3 mm), calcitic marbles with frequent, cm-thick, dark-greenish silicate layers containing diopside and tremolite; minor minerals include quartz, epidote, sulphides, Ba-feldspar, barite and, occasionally, phlogopite. First record of quarrying activities in the area arises to the Roman age (Ornavasso quarrying area). Both the Ornavasso and Candoglia Marbles were widely employed in local construction (San Nicola Church and Torre della Guardia at Ornavasso, Madonna di Campagna Church at Verbania, San Giovanni in Montorfano Church), but they became famous thanks to their application for the "Duomo di Milano" since the fourteenth century. At the beginning, the building stones employed for the construction of the Gothic style, Duomo di Milano were quarried in the Ornavasso area, but in a short time, the Candoglia quarry (property of the so-called "Veneranda Fabbrica del Duomo" that incessantly takes care of the Cathedral Church from 1387 A.D.) became the main quarry for the construction and maintenance of the Cathedral. The Candoglia quarry developed during the centuries, from open pit small quarries to a unique underground quarry, characterised by a very peculiar quarrying activities (subvertical bench characterized by strong lateral forces, which have to be contrasted and monitored). The Candoglia Marble was preferred to Carrara marbles also because of the more direct transport way from quarries to the construction yard: the transport were acted on big barges, from River Toce, across the Maggiore Lake and its emissary, the Ticino River, and then along the Naviglio Grande, up to the Milano Cathedral yard. The first saws driven by water wheels started to be employed in Candoglia to product slabs from stone blocks. Nowadays the working activities are both at Candoglia (block squaring activities and mason stone cutter laboratory) and in Milano (working plant). The peculiarity of the Candoglia Marble present exploitation is that all the quarried materials are used: as blocks (to produce the parts and sculptures for the Milano Cathedral maintenance), as armour stones (the irregular or not aesthetically suitable blocks) and as ornaments, furnishing, and jewels (the small pieces), so that everyone can potentially wear a "piece of history". The Candoglia Marble, for its petrological characteristics, its history, including the evolution of quarrying techniques and working activities, and its use in the construction and maintenance of the Milano Cathedral, represents an "unicum" that would deserve designation as Global Heritage Stone Resource.

Environmental Improvement Of Opencast Mining

NASA Astrophysics Data System (ADS)

Prokopenko, S.; Sushko, A.; Filatov, Yu; Kislyakov, M.; Kislyakov, I.

2017-01-01

Existing classifications of waste dumps in the quarries are given and their phenomenological nature is clarified. The need to identify the essence of the term "dump" is shown as well as the idea of "dump" as an artificial formation with everted and mixed rocks distanced from the quarry. Essential classification of man-made rock formations in quarries is developed. Characteristic of variations of man-made waste formations in quarries is developed. To reduce harmful effects of open-pit mining, dumps should be substituted with strat-lays - man-made structures relevant to natural stratification of litho-substances. Construction of strat-lays would improve ecological and technological culture of open cast mining.

Fluorspar

USGS Publications Warehouse

Miller, M.

2013-01-01

World fluorspar demand slowed in 2012 and, according to some sources prices decreased, especially in the latter half of the year. In 2012, nearly all fluorspar (CaF2) consumption in the United States was from imports. Hastie Mining and Trucking Co. produced some fluorspar as a byproduct of its limestone quarry operations in Illinois. In addition, a small amount of usable synthetic fluorspar was produced from industrial waste streams.

Quarries of Culture: An Ethnohistorical and Environmental Account of Sacred Sites and Rock Formations in Southern California's Mission Indian Country

ERIC Educational Resources Information Center

Karr, Steven M.

2005-01-01

Sacred sites and Rock Formations throughout Southern California's India Country are described by Indians as ancestral markers, origin and place-name locales, areas of deity habitation, and power sources. Early ethnographers were keen to record the traditional stories and meanings related to them by their Native collaborators. Rock formations…

Squid - a simple bioinformatics grid.

PubMed

Carvalho, Paulo C; Glória, Rafael V; de Miranda, Antonio B; Degrave, Wim M

2005-08-03

BLAST is a widely used genetic research tool for analysis of similarity between nucleotide and protein sequences. This paper presents a software application entitled "Squid" that makes use of grid technology. The current version, as an example, is configured for BLAST applications, but adaptation for other computing intensive repetitive tasks can be easily accomplished in the open source version. This enables the allocation of remote resources to perform distributed computing, making large BLAST queries viable without the need of high-end computers. Most distributed computing / grid solutions have complex installation procedures requiring a computer specialist, or have limitations regarding operating systems. Squid is a multi-platform, open-source program designed to "keep things simple" while offering high-end computing power for large scale applications. Squid also has an efficient fault tolerance and crash recovery system against data loss, being able to re-route jobs upon node failure and recover even if the master machine fails. Our results show that a Squid application, working with N nodes and proper network resources, can process BLAST queries almost N times faster than if working with only one computer. Squid offers high-end computing, even for the non-specialist, and is freely available at the project web site. Its open-source and binary Windows distributions contain detailed instructions and a "plug-n-play" instalation containing a pre-configured example.

Using a noise monitoring station in a small quarry located in an urban area.

PubMed

Wichers, Michiel; Iramina, Wilson Siguemasa; de Eston, Sérgio Médici; Ayres da Silva, Anna Luiza Marques

2017-12-22

Mining plays an important role in Brazilian exports. On the other hand, large urban centers like São Paulo, with approximately 21 million inhabitants, also demand an increasing domestic consumption of natural resources, such as construction aggregate. There are many quarries located in the surroundings of urban centers in Brazil, competing with the growth of urbanized areas. Such proximity leads to a series of conflicts involving quarries and surrounding communities, where the increase in noise levels is highlighted. Operations in quarries, in general, are intermittent. Noisier equipment, such as drilling rigs and primary crushers, operates only a few hours during the day, while other operations, such as screening and secondary and tertiary crushing, are more constant. This paper presents a study carried out in a quarry located near São Paulo, where in addition to conventional short term noise measurements at surrounding receptors, one noise monitoring station was installed, allowing to identify the noisiest moments during the quarry operating time. Through data transmitted by wireless technology, it was possible to follow the noise variations emitted from mining activities in real time and observe the noisiest events that were recorded for events that exceeded the established standards. A mobile application associated to this monitoring station facilitated the quarry's manager and employees to access immediately the monitoring information. Therefore, by using this system, it was possible to evaluate the effectiveness of noise reduction measures already taken and indicate what steps still need to be held.

Microbial Community Composition and Putative Biogeochemical Functions in the Sediment and Water of Tropical Granite Quarry Lakes.

PubMed

Kumar, Amit; Ng, Daphne H P; Wu, Yichao; Cao, Bin

2018-05-28

Re-naturalized quarry lakes are important ecosystems, which support complex communities of flora and fauna. Microorganisms associated with sediment and water form the lowest trophic level in these ecosystems and drive biogeochemical cycles. A direct comparison of microbial taxa in water and sediment microbial communities is lacking, which limits our understanding of the dominant functions that are carried out by the water and sediment microbial communities in quarry lakes. In this study, using the 16S rDNA amplicon sequencing approach, we compared microbial communities in the water and sediment in two re-naturalized quarry lakes in Singapore and elucidated putative functions of the sediment and water microbial communities in driving major biogeochemical processes. The richness and diversity of microbial communities in sediments of the quarry lakes were higher than those in the water. The composition of the microbial communities in the sediments from the two quarries was highly similar to one another, while those in the water differed greatly. Although the microbial communities of the sediment and water samples shared some common members, a large number of microbial taxa (at the phylum and genus levels) were prevalent either in sediment or water alone. Our results provide valuable insights into the prevalent biogeochemical processes carried out by water and sediment microbial communities in tropical granite quarry lakes, highlighting distinct microbial processes in water and sediment that contribute to the natural purification of the resident water.

Potential source for crushed granite aggregate in Heard County, Georgia

USGS Publications Warehouse

Atkins, R.L.; Higgins, Michael W.; Dickerson, Robert P.

1981-01-01

The production of crushed stone suitable for highway and general construction is a major industry in Georgia. The state ranks eighth in the nation in overall crushed stone production, and first in crushed granite production. Crushed stone production in Georgia in 1979 was 40,902,000 short tons worth $154,021,000 (D.H. White, Jr., US Bureau of Mines, personal commun., Aug. 1980). More than 3,000 people were employed by the crushed stone industry in Georgia during that year.Presently, the only active quarry in Heard County is located in an amphibolite. Amphibolite is not a conventional aggregate. It has a high specific gravity, a tendency to make elongate fragments, and varies considerably in abrasion tests.Because the nearest approved aggregate quarry is more than 25 miles from Franklin, the county seat, the purpose of this brief report is to describe a body of granite gneiss that may provide suitable aggregate for the crushed stone industry, potential quarry operators and various agencies in Heard County. This report is part of a project to study the geology and mineral resources of the Piedmont south of the Brevard Zone, and is not intended to supplant detailed site investigations by industry or consultants. The report is a joint effort between the Georgia Geologic Survey and the Office of Materials and Research of the Georgia Department of Transportation.

Statistical classification approach to discrimination between weak earthquakes and quarry blasts recorded by the Israel Seismic Network

NASA Astrophysics Data System (ADS)

Kushnir, A. F.; Troitsky, E. V.; Haikin, L. M.; Dainty, A.

1999-06-01

A semi-automatic procedure has been developed to achieve statistically optimum discrimination between earthquakes and explosions at local or regional distances based on a learning set specific to a given region. The method is used for step-by-step testing of candidate discrimination features to find the optimum (combination) subset of features, with the decision taken on a rigorous statistical basis. Linear (LDF) and Quadratic (QDF) Discriminant Functions based on Gaussian distributions of the discrimination features are implemented and statistically grounded; the features may be transformed by the Box-Cox transformation z=(1/ α)( yα-1) to make them more Gaussian. Tests of the method were successfully conducted on seismograms from the Israel Seismic Network using features consisting of spectral ratios between and within phases. Results showed that the QDF was more effective than the LDF and required five features out of 18 candidates for the optimum set. It was found that discrimination improved with increasing distance within the local range, and that eliminating transformation of the features and failing to correct for noise led to degradation of discrimination.

Is Blast Injury a Modern Phenomenon?: Early Historical Descriptions of Mining and Volcanic Traumatic Brain Injury With Relevance to Modern Terrorist Attacks and Military Warfare.

PubMed

Bowen, Lauren N; Moore, David F; Okun, Michael S

2016-03-01

Given the recent interest in blast injury spurred by returning soldiers from overseas conflicts, we sought to research the early historical descriptions of blast injuries and their treatments. Consideration was given to specific descriptions of survivors of closed head injury and their treatment. A review of the medical and nonmedical literature was undertaken, with particular emphasis on pre-1800 descriptions of volcanic eruptions and mining accidents. Compilations of accounts of the Etna eruptions dating from 126 BC were translated into English, and early mining texts from the 1600s and 1700s were reviewed. Accumulations of flammable gases were recorded in many medieval sources and this knowledge of toxic gas which could lead to blast injury was known in the mining community by 1316. No direct attribution of injuries to blast forces was present in the historical record examined before the 1300s, although mining accounts in the 1600s detail deaths due to blast. No specific descriptions of survivors of a closed head injury were found in the mining and volcanic eruption literature. Descriptions and warnings of blast forces were commonly written about in the medieval and Renaissance mining communities. Personal narratives as early as 1316 recognize the traumatic effects of blast injury. No mining or volcanic blast descriptions before 1800 detailed severe closed head injury survivors, suggesting greater mortality than morbidity from blast injury in the premodern era. This review also uncovered that there was no historical treatment or remedy recommended to survivors of blast injury. Blast explosions resulting in injury or death were frequently described, although in simplistic terminology.

Dynamic strain distribution of FRP plate under blast loading

NASA Astrophysics Data System (ADS)

Saburi, T.; Yoshida, M.; Kubota, S.

2017-02-01

The dynamic strain distribution of a fiber re-enforced plastic (FRP) plate under blast loading was investigated using a Digital Image Correlation (DIC) image analysis method. The testing FRP plates were mounted in parallel to each other on a steel frame. 50 g of composition C4 explosive was used as a blast loading source and set in the center of the FRP plates. The dynamic behavior of the FRP plate under blast loading were observed by two high-speed video cameras. The set of two high-speed video image sequences were used to analyze the FRP three-dimensional strain distribution by means of DIC method. A point strain profile extracted from the analyzed strain distribution data was compared with a directly observed strain profile using a strain gauge and it was shown that the strain profile under the blast loading by DIC method is quantitatively accurate.

Ecological filtering and plant traits variation across quarry geomorphological surfaces: implication for restoration.

PubMed

Gilardelli, Federica; Sgorbati, Sergio; Armiraglio, Stefano; Citterio, Sandra; Gentili, Rodolfo

2015-05-01

Revegetation patterns after quarry abandonment have been widely studied from several ecological points of view, but a trait-based approach is still lacking. The aim of this study was to characterise the plant species assemblages and the associated functional traits filtered on different geomorphological surfaces in abandoned limestone quarry areas: artificial cliffs, embankments, and platforms. We then verified if species with certain traits were better able to overcome the dispersal and environmental filters necessary for establishment. To this aim, we analyzed 113 vegetation plots and collected data on 25 morphological, ecological, and dispersal traits to detect species adaptaions across these man-made environments. As a case study, we investigated the extraction basin of Botticino (Lombardy, Italy), the second largest in Italy. The results obtained by SIMPER and CCA analyses showed that rockiness, stoniness, slope, elevation, and time of surfaces are the main filters that varied across quarries and affected plant assemblages at the macro-scale level. Across the three geomorphological surfaces (meso-scale) of quarries, more specific abiotic filters selecting species were found. In turn, traits differentiation according to the three main geomorphological surfaces of quarry emphasized that further filters acting at the micro-scale imply differences in dispersal mechanisms and resource availability. This work highlighted the utility to study species assemblages and environmental filters to address quarry restoration according to the type of geomorphological surface. The investigation of some traits (chorological form, life forms, seed dispersal,s and plant height) can furnish some interesting indications for practice individuating further abiotic filters acting at the micro-scale.

Identification of Quarries Rehabilitation Scenarios: A Case Study Within the Metropolitan Area of Bari (Italy)

NASA Astrophysics Data System (ADS)

Dal Sasso, Pasquale; Ottolino, Maria Antonella; Caliandro, Lucia Patrizia

2012-06-01

This paper addresses quarries rehabilitation issue within a Metropolitan Area. Areas where mining activity is carried out have been subjected to physical and environmental degradation linked both to pursue the building materials extraction and to the city expansion continuously asking for new areas to be developed with residential and service functions. These changes also occurred where environmental and landscape values are present. It has been therefore pointed out the issue of such areas redevelopment that, to be functionally reintegrated, must be consistently linked to the activities and the territorial local contexts characteristics. In this paper the quarries reuse issue is carried out through parameters identification able to define the quarries relationship with the neighboring towns and with their surroundings besides to identify their physical, environmental and landscaping characteristics. Quarry reuse alternatives have been identified among those consistent with the rehabilitation goals, as defined by the planning sector and internationally approved, while their selection is derived from the application of a two-step methodology: a multi-criteria analysis related to punctual parameters at a "site-specific" level, followed by a further territorial indicators checking over the wide area. This application has led to socially accepted results identifying the examined quarries for reuses ranging from agricultural-forestry and urban to functional or naturalistic. The proposed method has also proved to be suitable to address the abandoned quarries reuse problem with a systemic and consultative approach, as it is able to correlate the many variables present in the social and spatial complexity of the Metropolitan Areas.

Stone Quarries and Sourcing in the Carolina Slate Belt

DTIC Science & Technology

2006-04-01

a hilltop with a localized outcrop of small boulders of andesite porphyry . A revisit revealed that the site had recently been destroyed by...rocks are dacitic and include flows, tuffs, breccias, and porphyries . Metasedimentary rocks are metamudstone and fine metasandstone. The Uwharrie...Rocks of this zone, from Shingle Trap, Hattaway, and Sugarloaf Mountains, are mainly light to dark gray metadacite porphyry or metadacitic

40 CFR 421.75 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... produced Lead .000 .000 Zinc .000 .000 (c) Subpart G—Blast Furnace Slag Granulation. PSES Pollutant or... blast furance lead bullion produced Lead .000 .000 Zinc .000 .000 (d) Subpart G—Dross Reverberatory Slag... (pounds per billion pounds) of slag, speiss, or matte granulated Lead 1,612.000 748.400 Zinc 5,872.000 2...

40 CFR 421.75 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... produced Lead .000 .000 Zinc .000 .000 (c) Subpart G—Blast Furnace Slag Granulation. PSES Pollutant or... blast furance lead bullion produced Lead .000 .000 Zinc .000 .000 (d) Subpart G—Dross Reverberatory Slag... (pounds per billion pounds) of slag, speiss, or matte granulated Lead 1,612.000 748.400 Zinc 5,872.000 2...

Ground-water levels, water quality, and potential effects of toxic-substance spills or cessation of quarry dewatering near a municipal ground-water supply, southeastern Franklin County, Ohio

USGS Publications Warehouse

Sedam, A.C.; Eberts, S.M.; Bair, E.S.

1989-01-01

A newly completed municipal ground-water supply that produces from a sand and gravel aquifer in southern Franklin County, Ohio, may be susceptible to potential sources of pollution. Among these are spills of toxic substances that could enter recharge areas of the aquifer or be carried by surface drainage and subsequently enter the aquifer by induced infiltration. Ground water of degraded quality also is present in the vicinity of several landfills located upstream from the municipal supply. Local dewatering by quarrying operations has created a ground-water divide which, at present, prevents direct movement of the degraded ground water to the municipal supply. In addition, the dewatering has held water levels at the largest landfills below the base of the landfill. Should the dewatering cease, concern would be raised regarding the rise of water levels at this landfills and transport of contaminants through the aquifer to the Scioto River and subsequently by the river to the well field. From June 1984 through July 1986, the U.S. Geological Survey, in cooperation with the City of Columbus, Ohio, investigated the relations among the ground-water supply and potential sources of contamination by means of an observation-well network and a program of measuring water levels and sampling for water quality. Sample collections included those made to determine the baseline levels of organic chemicals and metals, as well as periodic sampling and analysis for common constituents to evaluate any changes taking place in the system. Finally, a steady-state, three-dimensional numerical model was used to determine ground-water flow directions and average ground-water velocities to asses potential effects of toxic-substance spills. The model also was used to simulate changes in the ground-water flow system that could result if part or all of the quarry dewatering ceased. Few of the organic-chemical and metal constituents analyzed for were present at detectable levels. With respect to chemical analysis of water and soil materials reported in earlier studies, no new problem areas were discovered as a result of either the baseline or periodic samplings. Model simulations suggest that, under March 1986 conditions, a toxic-substance spill along the major highways in the northern two-thirds of the study area eventually could discharge into one of the two quarries being dewatered or into the Scioto River. A toxic-substance spill in the southern one-third of the study area ultimately may discharge into the Scioto River, Big Walnut Creek, or possibly into the municipal ground-water supply. Model simulations also indicate that concentrated landfill leachate probably would not reach the municipal ground-water supply under current or well-field pumping conditions if dewatering ceased at either or both of the quarries.

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON THE FIRST BENCH, POWDER HILLS ARE PRIMED FOR DOLOMITE EXTRACTION. ON THE SECOND BENCH, THE DRILL TEAM IS LAYING OUT THE NEXT SHOTS. ON THE TOP BENCH, A 245 CATERPILLAR LOADER FILLS A 55-TON CATERPILLAR ROCK TRUCK WITH EXTRACTED DOLOMITE FOR TRANSPORT TO THE DOLOMITE CRUSHING AND SCREENING PLANT. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

Research on a Sudden Explosion and its Environmental Impact

NASA Astrophysics Data System (ADS)

Ye, Maosheng; Ma, Hui; Ni, Qingwei

2017-12-01

A sudden blast was chosen as the studied topic. Also, one computer based virtual experimentation was used to estimate the dimensional impact of initial pollutant plume from blasts. Self-made method using Mathcad code was used to generate the output for the period of the first tenth of a second (1deci-second) to 1minute (60s) of the blast at the point source. It also depicted long-range air pollution travel within the first 1 to 10 minutes. In the case study, it assumed an average directional diffusivity of 1720 m2s-1 which is about 25 per cent of the average generated speed of common explosives. The newly developed model revealed a plume cloud impact of 6.8×107µgm-3 in the first 1millisecond (0.01s) which decayed suddenly to a value of 1.7×107µgm-3 in the first 1decisecond (0.1s). The impact concentration at the point source by the end of the first second (1.0s) was 3.2×105µgm-3 which implied a 99.5% sudden decay when compared to 0.01s concentration value at the emission point source. Computerized experiments observed that air pollutants release from explosives/blasts were dispersed into the atmosphere in the first few seconds by forceful injection instead of by gradual dispersion as is the case with normal air pollutants plume releases.

Recycling of quarry waste as part of sustainable aggregate production: Norwegian and Italian point of view

NASA Astrophysics Data System (ADS)

Antonella Dino, Giovanna; Willy Danielsen, Svein; Chiappino, Claudia; Primavori, Piero; Engelsen, Christian John

2016-04-01

Resource preservation is one of the main challenges in Europe, together with waste management and recycling; recently several researchers are interested in the recovering of critical raw materials and secondary raw materials from landfill. Aggregate supply, even if it is not "critical" sensus stricto (s.s.), is one of the European priorities (low value but high volume needs). On the other side, the management of quarry waste , mainly from dimension stones, but also as fines from aggregate crushing, is still a matter of concern. Such materials are managed in different ways both locally and nationwide, and often they are landfilled, because of an unclear legislation and a general lack of data. Most of time the local authorities adopt the maximum precaution principle or the enterprises find it little profitable to recover them, so that the sustainable recycling of such material is not valued. Several studies have shown, depending on the material specific characteristics, the viability of recycling quarry waste into new raw materials used in glass and ceramic industries, precast concrete production, infrastructures etc. (Loudes et al. 2012, Dino&Marian 2015, Bozzola et al 2012, Dino et al. 2012, etc.). Thus, aggregate production may be one of the profitable ways to use quarry waste and is falling under the priority of EU (aggregate supply). Positive economic and environmental effects are likely to be achieved by systematic recycling of quarry waste planned by industries (industrial planning) and public authorities (national and local planning of aggregate exploitation). Today, the recycling level varies to a great extent and systematic recovery is not common among European Countries. In Italy and Norway no significant incentives on recycling or systematic approaches for local aggregate exploitation exist. The environmental consequences can be overexploitation of the natural resources, land take for the landfills, environmental contamination and landscape alteration by the quarry waste heaps. The environmentally sustainable management of quarry waste, which aims to recover and recycle both clean and contaminated materials, would therefore help to reduce the pressure on natural resources, reduce the land take and the environmental contamination. The present paper shows the main challenges connected to quarry waste management, focusing on several possibilities for quarry waste recovering, in order to produce recycled aggregates.

Identification of Groundwater Nitrate Contamination from Explosives Used in Road Construction: Isotopic, Chemical, and Hydrologic Evidence.

PubMed

Degnan, James R; Böhlke, J K; Pelham, Krystle; Langlais, David M; Walsh, Gregory J

2016-01-19

Explosives used in construction have been implicated as sources of NO3(-) contamination in groundwater, but direct forensic evidence is limited. Identification of blasting-related NO3(-) can be complicated by other NO3(-) sources, including agriculture and wastewater disposal, and by hydrogeologic factors affecting NO3(-) transport and stability. Here we describe a study that used hydrogeology, chemistry, stable isotopes, and mass balance calculations to evaluate groundwater NO3(-) sources and transport in areas surrounding a highway construction site with documented blasting in New Hampshire. Results indicate various groundwater responses to contamination: (1) rapid breakthrough and flushing of synthetic NO3(-) (low δ(15)N, high δ(18)O) from dissolution of unexploded NH4NO3 blasting agents in oxic groundwater; (2) delayed and reduced breakthrough of synthetic NO3(-) subjected to partial denitrification (high δ(15)N, high δ(18)O); (3) relatively persistent concentrations of blasting-related biogenic NO3(-) derived from nitrification of NH4(+) (low δ(15)N, low δ(18)O); and (4) stable but spatially variable biogenic NO3(-) concentrations, consistent with recharge from septic systems (high δ(15)N, low δ(18)O), variably affected by denitrification. Source characteristics of denitrified samples were reconstructed from dissolved-gas data (Ar, N2) and isotopic fractionation trends associated with denitrification (Δδ(15)N/Δδ(18)O ≈ 1.31). Methods and data from this study are expected to be applicable in studies of other aquifers affected by explosives used in construction.

Seismic Waveform Modeling of Broadband Data From a Temporary High-Density Deployment in the Los Angeles Basin

NASA Astrophysics Data System (ADS)

Herrman, M.; Polet, J.

2016-12-01

A total of 73 broadband seismometers were deployed for a passive source seismic experiment called the Los Angeles Syncline Seismic Interferometry Experiment (LASSIE) from September to November of 2014. The purpose of this experiment was to collect high density seismic data for the Los Angeles Basin (LAB) to better understand basin structure and response. This research will use the data collected from LASSIE to assess and refine current velocity models of the LAB using a full waveform modeling approach. To this end we will compare seismograms recorded by LASSIE for a subset of the 53 earthquakes and quarry blasts located by the Southern California Seismic Network (SCSN) that occurred within or near the LAB during the deployment period to synthetic seismograms generated by the Frequency-Wavenumber (FK) code developed by Zhu and Rivera (2002). A first analysis of the data indicates that roughly 25 of the 53 events have waveforms with sufficiently high signal to noise ratio, providing approximately 500 seismograms that are of suitable quality for comparison. We observe significant changes in waveform characteristics between stations with a very small separation distance of approximately 1 km. Focal mechanisms for most of these events have been obtained from Dr. Egill Hauksson (personal communication). We will show comparisons between the broadband velocity waveforms recorded by stations across the LASSIE array and FK synthetics determined for a variety of 1D velocity models that have been developed for the LAB area (such as Hadley and Kanamori, 1977; Hauksson, 1989, 1995 and Magistrale, 1992). The results of these comparisons will be analyzed to provide additional constraints on the subsurface seismic velocity structure within the Los Angeles basin.

Physical and mechanical properties of quarry dust waste incorporated into fired clay brick

NASA Astrophysics Data System (ADS)

Kadir, A. A.; Hassan, M. I. H.; Sarani, N. A.; Rahim, A. S. Abdul; Ismail, N.

2017-04-01

A large amount of quarry dust waste is dispose into landfills every year. This waste was obtained as a by-product during the production of aggregates through the crushing process of rocks in rubble crusher units. The increasing value of waste will have significant impact towards health and environment. Recycling such wastes by incorporating them into building materials is a practical solution for pollution problem. Therefore, this research was to examine the possibility of quarry dust to be incorporated in fired clay bricks. In this research, the composition and concentration of heavy metals were determined by using X-Ray Fluorescence Spectrometer (XRF). The research also consists of physical and mechanical properties of the fired clay bricks by utilizing quarry dust waste. Brick was manufactured by incorporating different percentages of quarry dust waste which are 0%, 10%, 20% and 30%. All bricks sample was tested with physical and mechanical properties which were density, shrinkage, initial rate of suction (IRS) and compressive strength of the fired bricks. Furthermore, the density and shrinkage were also in standard range. All physical and mechanical results were complied with the BS 3921:1985 standard. The comprehensive experimental work described in this research investigated the possibility of incorporating quarry dust into fired clay bricks. These materials could be an alternative low cost material for brick and at the same time provide a new disposal method for the waste.

Noise Exposure and Hearing Capabilities of Quarry Workers in Ghana: A Cross-Sectional Study

PubMed Central

Gyamfi, Charles Kwame R.; Amankwaa, Isaac; Owusu Sekyere, Frank; Boateng, Daniel

2016-01-01

Introduction. Although quarry operations have high economic significance, the effects they cause to the workers in terms of excessive noise production cannot be overlooked. This cross-sectional study assessed the extent of noise exposure and its influence on hearing capabilities among quarry workers in Ashanti region. Methods. The study involved 400 workers randomly selected from five quarries in Ashanti region from April to June 2012. Data was collected using structured questionnaires, physical examination, and audiological assessments. A logistic regression model was fitted to assess independent predictors of hearing loss. Results. All the machines used at the various quarries produced noise that exceeded the minimum threshold with levels ranging from 85.5 dBA to 102.7 dBA. 176 (44%) of study respondents had hearing threshold higher than 25 dBA. 18% and 2% of these were moderately (41–55 dBA) and severely (71–90 dBA) impaired, respectively. Age, duration of work, and use of earplugs independently predicted the development of hearing loss. Use of earplugs showed a protective effect on the development of hearing loss (OR = 0.45; 95% CI = 0.25, 0.84). Conclusion. This study provides empirical evidence on the extent of damage caused to quarry workers as a result of excessive noise exposure. This will support the institution of appropriate protective measures to minimize this threat. PMID:26904137

Introducing a new aspect in marble quarry rehabilitation in Greece

NASA Astrophysics Data System (ADS)

Kaliampakos, D. C.; Mavrikos, A. A.

2006-06-01

For many years the marble extraction sector of the Greek mining industry has been in conflict with the public, especially in terms of rehabilitation of marble quarry sites. One of the main reasons for that is that the marble extraction sector has been unable to adjust to the existing legislative guidelines for the rehabilitation, such as extensive backfilling and re-vegetation. In the majority of cases these methods fail due to erosion of the backfill soil and adverse climatic conditions. As a result the number of abandoned marble quarry sites is continuously increasing. The present paper suggests a different approach regarding the rehabilitation of marble quarries. More specifically, the paper questions the applicability, the effectiveness, and the social usefulness of the above-mentioned guidelines and suggests the establishment of new land-uses, which are based on an in-depth analysis of the area’s special features, by taking full advantage of its potentials. What is more, the rehabilitation scheme proposes that the new land-uses and the quarrying activity may co-exist and operate simultaneously for a long period of time.

Radium-226 content of agricultural gypsums

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lindeken, C.L.; Coles, D.G.

1977-01-01

Gypsum (CaSO/sub 4/ . 2H/sub 2/O), used as a soil amendment for saline-alkali soils, is obtained either by quarrying or as a by-product in the phosphate fertilizer industry. The latter, termed phospho gypsum, contains variable amounts of /sup 226/Ra, depending on the uranium content of the phosphate rock. Radium-226 contents of both quarried and phospho gypsum were determined by gamma counting in a low-background Ge(Li) spectrometer equipped with Compton suppression. Quarried samples from Nova Scotia, Iowa, Texas, and California were compared with phospho gypsum derived from Florida land pebble phosphates. Quarried gypsums showed an average radium content of 0.21 pCi/g.more » The average radium in phospho gypsum was 14.6 pCi/g. Uranium-238 measurements showed that near secular equilibrium existed between the uranium and radium in the quarried samples. Disequilibrium in the phospho gypsums occurred because of the preferential separation of radium during chemical processing. At the levels observed, no health hazard is implied from uptake of radium by plants grown in phospho gypsum treated soil.« less

Preliminary Geological Findings on the BP-1 Simulant

NASA Technical Reports Server (NTRS)

Stoeser, D. B.; Rickman, D. L.; Wilson, S.

2010-01-01

A waste material from an aggregate producing quarry has been used to make an inexpensive lunar simulant called BP-1. The feedstock is the Black Point lava flow in northern Arizona. Although this is part of the San Francisco volcanic field, which is also the source of the JSC-1 series feedstock, BP-1 and JSC-1 are distinct. Chemically, the Black Point flow is an amygdaloidal nepheline-bearing basalt. The amygdules are filled with secondary minerals containing opaline silica, calcium carbonate, and ferric iron minerals. X-ray diffraction (XRD) detected approximately 3% quartz, which is in line with tests done by the Kennedy Space Center Industrial Hygiene Office. Users of this material should use appropriate protective equipment. XRD also showed the presence of significant halite and some bassanite. Both are interpreted to be evaporative residues due to recycling of wash water at the quarry. The size distribution of BP-1 may be superior to some other simulants for some applications.

If it bleeds, it leads: the construction of workplace injury in Canadian newspapers, 2009-2014.

PubMed

Barnetson, Bob; Foster, Jason

2015-01-01

Public perceptions of workplace injuries are shaped by media reports, but the accuracy of such reports is unknown. This study identifies differences between workers' compensation claims data and newspaper reports of workplace injuries in Canadian newspapers and media sources. This study applies quantitative content analysis to 245 Canadian English-language newspaper articles from 2009 to 2014. Workers' compensation claims data is drawn from the Association of Workers' Compensation Boards of Canada. Newspapers dramatically overreport fatalities, injuries to men, injuries in the construction and mining/quarrying/oil industries, injuries stemming from contact with objects/equipment and fires/explosions, and acute physical injuries such as burns, fractures, intracranial injuries, and traumatic injuries. Newspaper reporters tend to rely upon government, police/firefighter, and employer accounts, rarely recounting the perspectives of workers. Newspapers overreported fatalities, injuries to men, and injuries in the construction and mining/quarrying/oil industries. This results in a misleading picture of occupational injuries in Canada.

If it bleeds, it leads: the construction of workplace injury in Canadian newspapers, 2009–2014

PubMed Central

Barnetson, Bob; Foster, Jason

2015-01-01

Background: Public perceptions of workplace injuries are shaped by media reports, but the accuracy of such reports is unknown. Objective: This study identifies differences between workers' compensation claims data and newspaper reports of workplace injuries in Canadian newspapers and media sources. Methods: This study applies quantitative content analysis to 245 Canadian English-language newspaper articles from 2009 to 2014. Workers' compensation claims data is drawn from the Association of Workers' Compensation Boards of Canada. Results: Newspapers dramatically overreport fatalities, injuries to men, injuries in the construction and mining/quarrying/oil industries, injuries stemming from contact with objects/equipment and fires/explosions, and acute physical injuries such as burns, fractures, intracranial injuries, and traumatic injuries. Newspaper reporters tend to rely upon government, police/firefighter, and employer accounts, rarely recounting the perspectives of workers. Conclusion: Newspapers overreported fatalities, injuries to men, and injuries in the construction and mining/quarrying/oil industries. This results in a misleading picture of occupational injuries in Canada. PMID:26070326

Contributions of non-destructive testing for determining the provenance of the granites used in the Roman Amphitheatre from Emerita Augusta, Badajoz, Spain.

NASA Astrophysics Data System (ADS)

Mota, M. Isabel; Alvarez de Buergo, Monica; Fort, Rafael; Pizzo, Antonio

2015-04-01

The Archaeological Ensemble of Emérita Augusta (Mérida, Badajoz, Spain) was listed a World Heritage Site in 1993 by UNESCO. One of the monuments that belongs to this Archaeological Ensemble is the Roman amphitheatre, mainly built with granite from quarries located near the city. Every urban centre in the Roman Empire, in addition to many rural sites, had one or more local quarries from which they extracted the bulk of their stone. In Mérida, there are a group of documented quarries located near the ancient city. In this work the authors have been investigating five of these documented outcrops which, due the distance from the monument or the existence of ancient Roman routes of communication with the city, can be the possible original quarries. The provenance of these materials with which the monument is built is of significant interest in terms of the restoration and conservation and from a historical point of view of the monument. Nowadays, there are many examples of identification of the original quarries that use destructive procedures and techniques which are based on the physical, petrographical, geochemical, magnetic or mechanical properties that are a function of the mineralogical and textural characteristics of the rock. In this work, the combined use of two non-destructive and on-site techniques, ultrasonic velocity and surface hardness determined with a Schmidt hammer rebound tester, allows to determine first, the quality and degree of decay in the granites, usually affecting the material surface and consisting of a decline in surface cohesion, and second, it can discriminate possible provenance areas of the rock used in the building. These two techniques are very useful for this purpose for several reasons. Their combined use allows the selection of the most representative blocks and ashlars for sampling. This reduces sampling to a minimum showing representative results for the whole building, especially in the case of performing ageing tests in the laboratory and when assessing consolidating and protecting treatments based on the similar decay condition present in the real structure; the combined values obtained from both techniques are directly and linearly related, can be used to compare the results from the building stones of the monument and from rocks from the surrounding documented quarries. The latter represents a suitable approach for locating the original quarries that supplied stone for construction and, in the case of many quarries having similar values, can be a method to exclude certain quarries. Moreover, the results also allow the identification of changes in determined physical properties of building stones, as porosity, mainly due to the exposure to climatic conditions, compared to fresh rocks from the quarries. The stones from the monument show lower ultrasonic and Schmidt hammer values than the rocks from the quarries. The obtained values from ultrasounds and from hardness surface measurement in the monument are affected by decay processes different from those in the quarries. This is due to the placement of ashlars in the monument (orientation), besides the cutting and carving of the stone and the surface finishing, which derives in a different correlation between the two sets of results from both techniques. Acknowledgements: to Geomateriales 2 programme (S2013/MIT-2914) funded by the Community of Madrid and to the Consorcio de la Ciudad Monumental de Mérida (Consortium of the Monumental City of Merida).

Numerical Simulation of Quarry Source and Reflection/Refraction Seismic Experiments

DTIC Science & Technology

1990-08-01

Prof. William Menke MIT-Lincoln Laboratory Lamont-Doherty Geological Observatory M-200B of Columbia University P. 0. Box 73 Palisades, NY 10964...University of Arizona Los Angeles, CA 90089-0741 Tucson, AZ 85721 Prof. Christopher H. Scholz Dr. William Wortman Lamont-Doherty Geological Observatory...Sunrise Valley Drive, Suite 1212 Stanford, CA 94305 Reston, VA 22091 Mr. William J. Best Prof. Robert W. Clayton 907 Westwood Drive Seismological

A preliminary sketch of the georesources in Niamey city (Niger)

NASA Astrophysics Data System (ADS)

Spadafora, Francesco; De Luca, Domenico A.; Antonella Dino, Giovanna; Lasagna, Manuela; Perotti, Luigi; Yadji, Guero; Tankari Dan-Badjo, Abdourahamane; Moussa, Issaka; Harouna, Moussa; Moussa, Konaté

2015-04-01

The present paper is about a preliminary study of the georesources (water and raw materials for construction) of Niamey city (Niger). Such research is part of an UNICOO project (funded by the University of Turin) and connected to the Edulink Cooperation Project (R.U.S.S.A.D.E.), a multidisciplinary project between Italy, Niger, Burquina Faso and Tchad funded on ACP- EU cooperation program in Higher Education. The main goals are the qualitative and quantitative characterization of the surface water and groundwater, and of aggregates (exploited in sands and gravel quarries). More specifically, at the beginning of the study there was a census of wells and quarries in the Niamey area, with a consequent sampling survey (surface water and groundwater sampling and aggregate sampling). After that, an in situ characterization was set: measure of piezometric levels in wells, water characterization (pH, electrolytic conductivity, temperature, nitrate and ammonia concentration) and an in situ evaluation of the quarrying techniques and quarry exploitation (present and old quarries). The samples were analyzed in Earth Science Dep. (UNITO) to evaluate the content of the main anions and cations (chemical analysis of sampled water) and the size distribution of the materials coming from the investigated quarries. Schematic reports of wells and quarries (location and features) were produced with the support of a Geodatabase with all available data. Geomatics instruments and methodologies (Geotagged Photos, Digital Mapping, GNSS Survey, Satellite Multitemporal Maps,) were basic starting point for the field data collection and a fundamental aid for data arrangement and final dissemination. The present study evidenced the actual condition of surface water and groundwater, also highlighting local phenomena of pollution. Nitrate in groundwater, i.e., showed locally concentration up to 5 times the WHO limit (50 mg/L). Thanks to the local quarry survey it was possible to evaluate how the open quarries works (open air yards, exploited by means of hand shovels and basic sieves) and what is the destination of the closed one (most of time the closed quarries are abandoned, not monitored and used as dumping areas, increasing the possibility of groundwater contamination). The safety condition of workers are very scarce: no protection devices, hard works and not safe yards (narrow tunnels, dug by hand and without protections). A sustainable management of natural resources and an appropriate environmental recovery are recommended, in order to prevent pollution and environmental deterioration. All the information arising from the present work are useful for local decision makers to enhance Niamey georesources management. At last, the information on water quality and quantity is fundamental in a wider perspective of food security and for life quality improvement. A final GIS project was prepared in order to have a good overview of the data and for dissemination purposes.

Overview of major hazards. Part 2: Source term; dispersion; combustion; blast, missiles, venting; fire; radiation; runaway reactions; toxic substances; dust explosions

NASA Astrophysics Data System (ADS)

Vilain, J.

Approaches to major hazard assessment and prediction are reviewed. Source term: (phenomenology/modeling of release, influence on early stages of dispersion); dispersion (atmospheric advection, diffusion and deposition, emphasis on dense/cold gases); combustion (flammable clouds and mists covering flash fires, deflagration, transition to detonation; mostly unconfined/partly confined situations); blast formation, propagation, interaction with structures; catastrophic fires (pool fires, torches and fireballs; highly reactive substances) runaway reactions; features of more general interest; toxic substances, excluding toxicology; and dust explosions (phenomenology and protective measures) are discussed.

Deep Impact Spots Quarry

NASA Image and Video Library

2005-04-27

Taken on April 25, 2005, sixty-nine days before it gets up-close-and-personal with a comet, NASA Deep Impact spacecraft successfully photographed its quarry, comet Tempel 1, at a distance of 39.7 million miles.

Volume Computation of a Stockpile - a Study Case Comparing GPS and Uav Measurements in AN Open Pit Quarry

NASA Astrophysics Data System (ADS)

Raeva, P. L.; Filipova, S. L.; Filipov, D. G.

2016-06-01

The following paper aims to test and evaluate the accuracy of UAV data for volumetric measurements to the conventional GNSS techniques. For this purpose, an appropriate open pit quarry has been chosen. Two sets of measurements were performed. Firstly, a stockpile was measured by GNSS technologies and later other terrestrial GNSS measurements for modelling the berms of the quarry were taken. Secondly, the area of the whole quarry including the stockpile site was mapped by a UAV flight. Having considered how dynamic our world is, new techniques and methods should be presented in numerous fields. For instance, the management of an open pit quarry requires gaining, processing and storing a large amount of information which is constantly changing with time. Fast and precise acquisition of measurements regarding the process taking place in a quarry is the key to an effective and stable maintenance. In other words, this means getting an objective evaluations of the processes, using up-to-date technologies and reliable accuracy of the results. Often legislations concerning mine engineering state that the volumetric calculations are to present ±3% accuracy of the whole amount. On one hand, extremely precise measurements could be performed by GNSS technologies, however, it could be really time consuming. On the other hand, UAV photogrammetry presents a fast, accurate method for mapping large areas and calculating stockpiles volumes. The study case was performed as a part of a master thesis.

Characterizing the microbial colonization of a dolostone quarry: implications for stone biodeterioration and response to biocide treatments.

PubMed

Cámara, Beatriz; De los Ríos, Asuncion; Urizal, Marta; de Buergo, Mónica Alvarez; Varas, Maria Jose; Fort, Rafael; Ascaso, Carmen

2011-08-01

This study examines the microbial colonization of three fronts of an abandoned dolostone quarry (Redueña, Madrid, Spain) exposed to atmospheric conditions for different time periods since Roman times to the present. Through scanning electron microscopy in backscattered electron mode (SEM-BSE), endolithic colonization was predominantly detected in the most recently exposed front, while in the longer exposed quarry fronts, epilithic forms of growth were most often observed. These observations were confirmed by denaturing gradient gel electrophoresis (DGGE) analysis. Based on the distribution pattern of microbial colonization in the different quarry fronts, we then established a sequence of colonization events that took place over this long time frame. Bioalteration processes related to this sequential colonization were also identified. Characterizing these sequential processes can be useful for interpreting biodeterioration processes in historic dolostone monuments, especially those affecting constructions in the area of the Redueña stone quarry. In a second experimental stage, different biocide treatments were tested on this quarry rock to find the best way to avoid the microbial colonization effects identified. Through combined SEM-BSE/DGGE analysis, the efficacy of several biocides against the microorganisms inhabiting the dolostones was assessed after 4 and 16 months treatment. In general, all treatments were effective at reducing around 80% of the lichen cover, although effects on endolithic lithobiontic communities were dependent on how well the rock surface had been mechanically cleaned prior to treatment and gradually disappeared over time.

The Solnhofen Limestone: A stony heritage of many uses

NASA Astrophysics Data System (ADS)

Kölbl-Ebert, Martina; Kramar, Sabina; Cooper, Barry J.

2016-04-01

High above the valley of the River Altmühl (Bavaria, Germany), between Solnhofen to the west and Kelheim to the east, numerous quarries give access to thinly plated limestone from the Upper Jurassic, some 150 million years before the present. The main quarry areas lie around the town of Eichstätt and between the villages of Solnhofen, Langenaltheim and Mörnsheim. Here limestone slabs have been quarried for several hundred years, some even in Roman times. Solnhofen Limestone is famous worldwide; not only because it is a beautiful building stone of high quality, but also because of the exceptionally well-preserved fossils it contains -among them the early bird Archaeopteryx. The quarry industry between Solnhofen and Eichstätt has shaped a cultural landscape, with old and new quarries sunk into the plain and numerous spoil heaps rising above it, for the rock is not all economically useful. But many of the spoil heaps and the old quarries are environmentally protected as they provide a habitat for some rare plants and animals. It is not necessary to cut the Solnhofen Limestone with a saw: it is split by hand into thin and even slabs or sheets which are used for flagstones and wall covers, which since centuries are sold world-wide. Locally it also serves as roof tiles for traditional houses. Thick slabs of especially fine quality may be found near Solnhofen and Mörnsheim and are used for lithography printing.

A procedure to evaluate environmental rehabilitation in limestone quarries.

PubMed

Neri, Ana Claudia; Sánchez, Luis Enrique

2010-11-01

A procedure to evaluate mine rehabilitation practices during the operational phase was developed and validated. It is based on a comparison of actually observed or documented practices with internationally recommended best practices (BP). A set of 150 BP statements was derived from international guides in order to establish the benchmark. The statements are arranged in six rehabilitation programs under three categories: (1) planning (2) operational and (3) management, corresponding to the adoption of the plan-do-check-act management systems model to mine rehabilitation. The procedure consists of (i) performing technical inspections guided by a series of field forms containing BP statements; (ii) classifying evidences in five categories; and (iii) calculating conformity indexes and levels. For testing and calibration purposes, the procedure was applied to nine limestone quarries and conformity indexes were calculated for the rehabilitation programs in each quarry. Most quarries featured poor planning practices, operational practices reached high conformity levels in 50% of the cases and management practices scored moderate conformity. Despite all quarries being ISO 14001 certified, their management systems pay low attention to issues pertaining to land rehabilitation and biodiversity. The best results were achieved by a quarry whose expansion was recently submitted to the environmental impact assessment process, suggesting that public scrutiny may play a positive role in enhancing rehabilitation practices. Conformity indexes and levels can be used to chart the evolution of rehabilitation practices at regular intervals, to establish corporate goals and for communication with stakeholders. Copyright 2010 Elsevier Ltd. All rights reserved.

Prevention of Blast-Related Injuries

DTIC Science & Technology

2013-07-01

collection of information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources...of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1 . REPORT DATE...Introduction 4 Statement of Work 4 Task I Report 4 1 . Adjustment of the experimental design and methodology 4 2. Preparations for Blast

Characterization of resistance genes to rice blast fungus Magnaporthe oryzae in a “Green Revolution” rice variety

USDA-ARS?s Scientific Manuscript database

The indica rice variety Dee Geo Woo Gen (DGWG) was the source of the semi-dwarf gene (SD1) which played an important role in the Green Revolution. In the present study, resistance (R) genes to the U.S. race (isolate) IB54 of Magnaporthe oryzae, causal agent of rice blast disease, was investigated. T...

Computational Hydrocode Study of Target Damage due to Fragment-Blast Impact

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hatch-Aguilar, T; Najjar, F; Szymanski, E

2011-03-24

A target's terminal ballistic effects involving explosively generated fragments, along with the original blast, are of critical importance for many different security and safety related applications. Personnel safety and protective building design are but a few of the practical disciplines that can gain from improved understanding combined loading effects. Traditionally, any engineering level analysis or design effort involving explosions would divide the target damage analysis into two correspondingly critical areas: blast wave and fragment related impact effects. The hypothesis of this paper lies in the supposition that a linear combination of a blast-fragment loading, coupled with an accurate target responsemore » description, can lead to a non-linear target damage effect. This non-linear target response could then stand as the basis of defining what a synergistic or combined frag-blast loading might actually look like. The table below, taken from Walters, et. al. categorizes some of the critical parameters driving any combined target damage effect and drives the evaluation of results. Based on table 1 it becomes clear that any combined frag-blast analysis would need to account for the target response matching similar ranges for the mechanics described above. Of interest are the critical times upon which a blast event or fragment impact loading occurs relative to the target's modal response. A blast, for the purposes of this paper is defined as the sudden release of chemical energy from a given material (henceforth referred to as an energetic material) onto its surrounding medium. During the coupling mechanism a discrete or discontinuous shockwave is generated. This shockwave travels outward from the source transferring energy and momentum to any surrounding objects including personnel and engineering structures. From an engineering perspective blast effects are typically characterized by way of physical characteristics such as Peak Pressure (PP), Time of Arrival (TOA), Pressure-Impulse (PI) and Time of Duration (TD). Other peculiarities include the radial decrease in pressure from the source, any fireball size measurement, and subsequent increase in temperature from the passing of the shockwave through the surrounding medium. In light of all of these metrics, the loading any object receives from a blast event becomes intricately connected to the distance between itself and the source. Because of this, a clear distinction is made between close-in effects and those from a source far away from the object of interest. Explosively generated fragments on the other hand are characterized by means of their localized damage potential. Metrics such as whether the fragment penetrates or perforates a given object is quantified as well as other variables including fragment's residual velocity, % kinetic energy decrease, residual fragment mass and other exit criteria. A fragment launched under such violent conditions could easily be traveling at speeds in excess of 2500 ft/s. Given these speeds it is conceivable to imagine how any given fragment could deliver a concentrated load to a target and penetrates through walls, vehicles or even the protection systems of nearby personnel. This study will focus on the individual fragment-target impact event with the hopes of expanding it to eventually include statistical procedures. Since this is a modeling excursion into the combined frag-blast target damage effects the numerical methods used to frame this problem become important in-so-far as the simulations are done in a consistent manner. For this study a Finite-Element based Hydrocode solution called ALE3D (ALE=Arbitrary Lagrangian-Eulerian) was utilized. ALE3D is developed by Lawrence Livermore National Laboratory (Livermore, CA), and as this paper will show, successfully implemented a converged ALE formulation including as many of the different aspects needed to query the synergistic damage on a given target. Further information on the modeling setup is included.« less

Ultrafine Particle Distribution and Chemical Composition Assessment during Military Operative Trainings

PubMed Central

Campagna, Marcello; Pilia, Ilaria; Marcias, Gabriele; Frattolillo, Andrea; Pili, Sergio; Bernabei, Manuele; d’Aloja, Ernesto; Cocco, Pierluigi; Buonanno, Giorgio

2017-01-01

(1) Background: The assessment of airborne particulate matter (PM) and ultrafine particles (UFPs) in battlefield scenarios is a topic of particular concern; (2) Methods: Size distribution, concentration, and chemical composition of UFPs during operative military training activities (target drone launches, ammunition blasting, and inert bomb impact) were investigated using an electric low-pressure impactor (ELPI+) and a scanning electron microscope (SEM), equipped with energy-dispersive spectroscopy (EDS); (3) Results: The median of UFPs, measured for all sampling periods and at variable distance from sources, was between 1.02 × 103 and 3.75 × 103 particles/cm3 for drone launches, between 3.32 × 103 and 15.4 × 103 particles/cm3 for the ammunition blasting and from 7.9 × 103 to 1.3 × 104 particles/cm3 for inert launches. Maximum peak concentrations, during emitting sources starting, were 75.5 × 106 and 17.9 × 106 particles/cm3, respectively. Particles from the drone launches were predominantly composed of silicon (Si), iron (Fe) and calcium (Ca), and those from the blasting campaigns by magnesium (Mg), sulphur (S), aluminum (Al), iron (Fe), barium (Ba) and silicon (Si); (4) Conclusions: The investigated sources produced UFPs with median values lower than other anthropogenic sources, and with a similar chemical composition. PMID:28556812

Identification of groundwater nitrate contamination from explosives used in road construction: Isotopic, chemical, and hydrologic evidence

USGS Publications Warehouse

Degnan, James R.; Böhlke, John Karl; Pelham, Krystle; David M. Langlais,; Walsh, Gregory J.

2015-01-01

Explosives used in construction have been implicated as sources of NO3– contamination in groundwater, but direct forensic evidence is limited. Identification of blasting-related NO3– can be complicated by other NO3– sources, including agriculture and wastewater disposal, and by hydrogeologic factors affecting NO3– transport and stability. Here we describe a study that used hydrogeology, chemistry, stable isotopes, and mass balance calculations to evaluate groundwater NO3– sources and transport in areas surrounding a highway construction site with documented blasting in New Hampshire. Results indicate various groundwater responses to contamination: (1) rapid breakthrough and flushing of synthetic NO3– (low δ15N, high δ18O) from dissolution of unexploded NH4NO3 blasting agents in oxic groundwater; (2) delayed and reduced breakthrough of synthetic NO3– subjected to partial denitrification (high δ15N, high δ18O); (3) relatively persistent concentrations of blasting-related biogenic NO3– derived from nitrification of NH4+ (low δ15N, low δ18O); and (4) stable but spatially variable biogenic NO3– concentrations, consistent with recharge from septic systems (high δ15N, low δ18O), variably affected by denitrification. Source characteristics of denitrified samples were reconstructed from dissolved-gas data (Ar, N2) and isotopic fractionation trends associated with denitrification (Δδ15N/Δδ18O ≈ 1.31). Methods and data from this study are expected to be applicable in studies of other aquifers affected by explosives used in construction.

Nature of the Paleocene/Eocene (P/E) boundary in Sinai, Egypt

NASA Astrophysics Data System (ADS)

Obaidalla, Nageh A.; Abdel-Maksoud, Nasr A.; Hosny, Atef M.; Mahfouz, Kamel H.

2017-12-01

The P/E boundary is studied at eight stratigraphic sections in Sinai, Egypt, which are nearly distributed in a stratigraphic profile from north to south as follows: Al-Hasanah, Sudr Al-Hitan, Wadi Sudr, Al-Thamad, Abu Qada, Wadi Matulla, Wadi Nukhul and Wadi Feiran. This study includes field, litho- and bio-stratigraphic analyses that enabled to delineate several hiatuses which may be due to the occurrence of tectonic activity that may be related to the echo of the Syrian Arc Orogeny at the P/E boundary. Generally, in Egypt the P/E boundary is marked by the occurrence of distinctive five beds, named by El Dababiya Quarry Member. At Wadi Nukhul, Wadi Matulla and Wadi Feiran sections, El Dababiya Quarry Member is well represented and the P/E boundary is conformable and resembles the GSSP section. Although El Dababiya Quarry Member is represented at Al-Hasanah section, the P/E boundary is marked by the occurrence of a minor hiatus at the end of Paleocene. Moreover, at Al Thamad section, El Dababiya Quarry Member is partially represented. On the other hand, at Sudr Al-Hitan, Wadi Sudr and Abu Qada sections, El Dababiya Quarry Member is completely absent due to a major hiatus.

7. WEST DAM STRUCTURE, LOOKING NORTHWEST. QUARRIES AT BOTTOM; OUTLET ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. WEST DAM STRUCTURE, LOOKING NORTHWEST. QUARRIES AT BOTTOM; OUTLET STRUCTURE UNDER CONSTRUCTION CUTTING INTO HILL AT TOP OF PICTURE. - Eastside Reservoir, Diamond & Domenigoni Valleys, southwest of Hemet, Hemet, Riverside County, CA

Interior of Mess Hall, showing original columns and quarry tile ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior of Mess Hall, showing original columns and quarry tile floor - U.S. Naval Base, Pearl Harbor, Barracks & Mess Hall, Hornet Avenue between Liscome Bay & Enterprise Streets, Pearl City, Honolulu County, HI

The Landforms of Granitic Rocks: An Annotated Bibliography

DTIC Science & Technology

1990-05-01

major sources of copper , tin, silver, gold, and many other valuable commodities. They are naturally highly radioactive, particularly at depth, and are...et al., 1978). Kesel (1977) cited sheeting and spalling as the major process in central Arizona . Crystal growth, usually salt or ice, is a common...quarries; and 4) aplite veins and dikes. Tin is found on Dartmoor, but copper is common only around the edges. Tin and copper lodes run east-west and

On meteor-generated infrasound. [propagation characteristics during entry into earth atmosphere

NASA Technical Reports Server (NTRS)

Revelle, D. O.

1976-01-01

The characteristics of generation and propagation of infrasonic pressure waves excited during meteor entry into the earth's atmosphere are studied. Existing line source blast wave theory is applied to infrasonic airwave data from four bright fire-balls. It is shown that the strong shock behavior of the blast wave is confined to a cylinderical region with a radius proportional to the product of the meteor Mach number and its diameter. A description of the wave form far from the source is provided. Infrasonic data reported elsewhere are analyzed. All the results should be considered as preliminary, and additional work is under way to refine the estimates obtained.

3-D P- and S-wave velocity structure and low-frequency earthquake locations in the Parkfield, California region

USGS Publications Warehouse

Zeng, Xiangfang; Thurber, Clifford H.; Shelly, David R.; Harrington, Rebecca M.; Cochran, Elizabeth S.; Bennington, Ninfa L.; Peterson, Dana; Guo, Bin; McClement, Kara

2016-01-01

To refine the 3-D seismic velocity model in the greater Parkfield, California region, a new data set including regular earthquakes, shots, quarry blasts and low-frequency earthquakes (LFEs) was assembled. Hundreds of traces of each LFE family at two temporary arrays were stacked with time–frequency domain phase weighted stacking method to improve signal-to-noise ratio. We extend our model resolution to lower crustal depth with LFE data. Our result images not only previously identified features but also low velocity zones (LVZs) in the area around the LFEs and the lower crust beneath the southern Rinconada Fault. The former LVZ is consistent with high fluid pressure that can account for several aspects of LFE behaviour. The latter LVZ is consistent with a high conductivity zone in magnetotelluric studies. A new Vs model was developed with S picks that were obtained with a new autopicker. At shallow depth, the low Vs areas underlie the strongest shaking areas in the 2004 Parkfield earthquake. We relocate LFE families and analyse the location uncertainties with the NonLinLoc and tomoDD codes. The two methods yield similar results.

Carbon Rod Radiant Source for Blast/Fire Interaction Experiments: Proof of Concept and Design.

DTIC Science & Technology

1980-08-30

Contracting Officer’s Technical Representative was David W. Bensen ISt. KEY IFORCS (C~rnuen orm rwv.,,, took of otarfam d *Oent.-y by block fmtr.) Blast/F...42 13b Irradiance at Target Surface Elliptical Reflectors .. ..... 43 13c Irradiance at Target Surface Parabolic and Elliptical Reflectors...44 14 Flux Distribution at Target Surface for One Rod, Parabolic and Elliptical Reflectors ...................... 15

Geochronological and Taxonomic Revisions of the Middle Eocene Whistler Squat Quarry (Devil’s Graveyard Formation, Texas) and Implications for the Early Uintan in Trans-Pecos Texas

PubMed Central

Campisano, Christopher J.; Kirk, E. Christopher; Townsend, K. E. Beth; Deino, Alan L.

2014-01-01

The Whistler Squat Quarry (TMM 41372) of the lower Devil’s Graveyard Formation in Trans-Pecos Texas is a middle Eocene fossil locality attributed to Uintan biochronological zone Ui1b. Specimens from the Whistler Squat Quarry were collected immediately above a volcanic tuff with prior K/Ar ages ranging from ∼47–50 Ma and below a tuff previously dated to ∼44 Ma. New 40Ar/39Ar analyses of both of the original tuff samples provide statistically indistinguishable ages of 44.88±0.04 Ma for the lower tuff and 45.04±0.10 Ma for the upper tuff. These dates are compatible with magnetically reversed sediments at the site attributable to C20r (43.505–45.942 Ma) and a stratigraphic position above a basalt dated to 46.80 Ma. Our reanalysis of mammalian specimens from the Whistler Squat Quarry and a stratigraphically equivalent locality significantly revises their faunal lists, confirms the early Uintan designation for the sites, and highlights several biogeographic and biochronological differences when compared to stratotypes in the Bridger and Uinta Formations. Previous suggestions of regional endemism in the early Uintan are supported by the recognition of six endemic taxa (26% of mammalian taxa) from the Whistler Squat Quarry alone, including three new taxa. The revised faunal list for the Whistler Squat Quarry also extends the biostratigraphic ranges of nine non-endemic mammalian taxa to Ui1b. PMID:24988115

Development of an Animal Model for Burn-Blast Combined Injury and Cardiopulmonary System Changes in the Early Shock Stage.

PubMed

Hu, Quan; Chai, Jiake; Hu, Sen; Fan, Jun; Wang, Hong-Wei; Ma, Li; Duan, Hong-Jie; Liu, Lingying; Yang, Hongming; Li, Bai-Ling; Wang, Yi-He

2015-12-01

The purposes of this study were to establish an animal model for burn-blast combined injury research and elaborate cardiopulmonary system changes in the early shock stage. In this study, royal demolition explosive or RDX (hexagon, ring trimethylene nitramine) was used as an explosive source, and the injury conditions of the canine test subjects at various distances to the explosion (30, 50, and 70 cm) were observed by gross anatomy and pathology to determine a larger animal model of moderate blast injury. The canines were then subjected to a 35 % total body surface area (TBSA) full-thickness flame injury using napalm, which completed the development of a burn-blast combined injury model. Based on this model, the hemodynamic changes and arterial blood gas analysis after the burn-blast combined injury were measured to identify the cardiopulmonary system characteristics. In this research, RDX explosion and flame injury were used to develop a severe burn-blast injury animal model that was stable, close to reality, and easily controllable. The hemodynamic and arterial blood gas changes in the canine subjects after burn-blast injury changed distinctly from the burn and blast injuries. Blood pressure and cardiac output fluctuated, and the preload was significantly reduced, whereas the afterload significantly increased. Meanwhile, the oxygen saturation (SO2) decreased markedly with carbon dioxide partial pressure (PCO2), and lactic acid (Lac) rose, and oxygen partial pressure (PO2) reduced. These changes suggested that immediate clinical treatment is important during burn-blast injury both to stabilize cardiac function and supply blood volume and to reduce the vascular permeability, thereby preventing acute pneumonedema or other complications.

Simulation of detonation cell kinematics using two-dimensional reactive blast waves

NASA Astrophysics Data System (ADS)

Thomas, G. O.; Edwards, D. H.

1983-10-01

A method of generating a cylindrical blast wave is developed which overcomes the disadvantages inherent in the converging-diverging nozzle technique used by Edwards et al., 1981. It is demonstrated than an exploding wire placed at the apex of a two-dimensional sector provides a satisfactory source of the generation of blast waves in reactive systems. The velocity profiles of the blast waves are found to simulate those in freely propagating detonations very well, and this method does not suffer from the disadvantage of having the mass flow at the throat as in the nozzle method. The density decay parameter is determined to have a constant value of 4 in the systems investigated, and it is suggested that this may be a universal value. It is proposed that suitable wedges could be used to create artificial Mach stems in the same manner as Strehlow and Barthel (1971) without the attendant disadvantages of the nozzle method.

Stone Quarrying, Crushing and Screening Facilities General Air Quality Permit Request for Coverage: US Silica - Parshall Transload Facility

EPA Pesticide Factsheets

Documents related to Request for Coverage under Stone Quarrying, Crushing, and Screening Facilities General Permit Indian Reservation, US Silica, Parshall Transload Facility, Fort Berthold Indian Reservation, North Dakota.

DETAIL OF TWO LARGE BORE HOLES ON TOP OF SOUTH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OF TWO LARGE BORE HOLES ON TOP OF SOUTH QUARRY WALL, FACING NORTH - Granite Hill Plantation, Quarry No. 1, South side of State Route 16, 1.3 miles northeast east of Sparta, Sparta, Hancock County, GA

VIEW OF PARALLEL LINE OF LARGE BORE HOLES IN NORTHERN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF PARALLEL LINE OF LARGE BORE HOLES IN NORTHERN QUARRY AREA, FACING NORTHEAST - Granite Hill Plantation, Quarry No. 2, South side of State Route 16, 1.3 miles northeast east of Sparta, Sparta, Hancock County, GA

Gangliosides and Ceramides Change in a Mouse Model of Blast Induced Traumatic Brain Injury

PubMed Central

2013-01-01

Explosive detonations generate atmospheric pressure changes that produce nonpenetrating blast induced “mild” traumatic brain injury (bTBI). The structural basis for mild bTBI has been extremely controversial. The present study applies matrix-assisted laser desorption/ionization (MALDI) mass spectrometry imaging to track the distribution of gangliosides in mouse brain tissue that were exposed to very low level of explosive detonations (2.5–5.5 psi peak overpressure). We observed major increases of the ganglioside GM2 in the hippocampus, thalamus, and hypothalamus after a single blast exposure. Moreover, these changes were accompanied by depletion of ceramides. No neurological or brain structural signs of injury could be inferred using standard light microscopic techniques. The first source of variability is generated by the Latency between blast and tissue sampling (peak intensity of the blast wave). These findings suggest that subtle molecular changes in intracellular membranes and plasmalemma compartments may be biomarkers for biological responses to mild bTBI. This is also the first report of a GM2 increase in the brains of mature mice from a nongenetic etiology. PMID:23590251

PLAN: a web platform for automating high-throughput BLAST searches and for managing and mining results.

PubMed

He, Ji; Dai, Xinbin; Zhao, Xuechun

2007-02-09

BLAST searches are widely used for sequence alignment. The search results are commonly adopted for various functional and comparative genomics tasks such as annotating unknown sequences, investigating gene models and comparing two sequence sets. Advances in sequencing technologies pose challenges for high-throughput analysis of large-scale sequence data. A number of programs and hardware solutions exist for efficient BLAST searching, but there is a lack of generic software solutions for mining and personalized management of the results. Systematically reviewing the results and identifying information of interest remains tedious and time-consuming. Personal BLAST Navigator (PLAN) is a versatile web platform that helps users to carry out various personalized pre- and post-BLAST tasks, including: (1) query and target sequence database management, (2) automated high-throughput BLAST searching, (3) indexing and searching of results, (4) filtering results online, (5) managing results of personal interest in favorite categories, (6) automated sequence annotation (such as NCBI NR and ontology-based annotation). PLAN integrates, by default, the Decypher hardware-based BLAST solution provided by Active Motif Inc. with a greatly improved efficiency over conventional BLAST software. BLAST results are visualized by spreadsheets and graphs and are full-text searchable. BLAST results and sequence annotations can be exported, in part or in full, in various formats including Microsoft Excel and FASTA. Sequences and BLAST results are organized in projects, the data publication levels of which are controlled by the registered project owners. In addition, all analytical functions are provided to public users without registration. PLAN has proved a valuable addition to the community for automated high-throughput BLAST searches, and, more importantly, for knowledge discovery, management and sharing based on sequence alignment results. The PLAN web interface is platform-independent, easily configurable and capable of comprehensive expansion, and user-intuitive. PLAN is freely available to academic users at http://bioinfo.noble.org/plan/. The source code for local deployment is provided under free license. Full support on system utilization, installation, configuration and customization are provided to academic users.

PLAN: a web platform for automating high-throughput BLAST searches and for managing and mining results

PubMed Central

He, Ji; Dai, Xinbin; Zhao, Xuechun

2007-01-01

Background BLAST searches are widely used for sequence alignment. The search results are commonly adopted for various functional and comparative genomics tasks such as annotating unknown sequences, investigating gene models and comparing two sequence sets. Advances in sequencing technologies pose challenges for high-throughput analysis of large-scale sequence data. A number of programs and hardware solutions exist for efficient BLAST searching, but there is a lack of generic software solutions for mining and personalized management of the results. Systematically reviewing the results and identifying information of interest remains tedious and time-consuming. Results Personal BLAST Navigator (PLAN) is a versatile web platform that helps users to carry out various personalized pre- and post-BLAST tasks, including: (1) query and target sequence database management, (2) automated high-throughput BLAST searching, (3) indexing and searching of results, (4) filtering results online, (5) managing results of personal interest in favorite categories, (6) automated sequence annotation (such as NCBI NR and ontology-based annotation). PLAN integrates, by default, the Decypher hardware-based BLAST solution provided by Active Motif Inc. with a greatly improved efficiency over conventional BLAST software. BLAST results are visualized by spreadsheets and graphs and are full-text searchable. BLAST results and sequence annotations can be exported, in part or in full, in various formats including Microsoft Excel and FASTA. Sequences and BLAST results are organized in projects, the data publication levels of which are controlled by the registered project owners. In addition, all analytical functions are provided to public users without registration. Conclusion PLAN has proved a valuable addition to the community for automated high-throughput BLAST searches, and, more importantly, for knowledge discovery, management and sharing based on sequence alignment results. The PLAN web interface is platform-independent, easily configurable and capable of comprehensive expansion, and user-intuitive. PLAN is freely available to academic users at . The source code for local deployment is provided under free license. Full support on system utilization, installation, configuration and customization are provided to academic users. PMID:17291345

Mathematical theory of cylindrical isothermal blast waves in a magnetic field. [with application to supernova remnant evolution

NASA Technical Reports Server (NTRS)

Lerche, I.

1981-01-01

An analysis is conducted regarding the properties of cylindrically symmetric self-similar blast waves propagating away from a line source into a medium whose density and magnetic field (with components in both the phi and z directions) both vary as r to the -(omega) power (with omega less than 1) ahead of the blast wave. The main results of the analysis can be divided into two classes, related to a zero azimuthal field and a zero longitudinal field. In the case of the zero longitudinal field it is found that there are no physically acceptable solutions with continuous postshock variations of flow speed and gas density.

Blast-Loading Assessment of Multi-Energy Flash Computed Tomography (MEFCT) Diagnostic

DTIC Science & Technology

2016-08-01

Perrella JA, Sturgill JM. Design of a simple blast pressure gauge based on a heterodyne velocimetry measuring technique. Aberdeen Proving Ground (MD...position unless so designated by other authorized documents. Citation of manufacturer’s or trade names does not constitute an official endorsement or...of the radiation dose throughout the angular span of the 150-, 300-, and 450-kV flash X-ray sources used in the MEFCT diagnostic: left image shows

Primary blast-induced traumatic brain injury: lessons from lithotripsy

NASA Astrophysics Data System (ADS)

Nakagawa, A.; Ohtani, K.; Armonda, R.; Tomita, H.; Sakuma, A.; Mugikura, S.; Takayama, K.; Kushimoto, S.; Tominaga, T.

2017-11-01

Traumatic injury caused by explosive or blast events is traditionally divided into four mechanisms: primary, secondary, tertiary, and quaternary blast injury. The mechanisms of blast-induced traumatic brain injury (bTBI) are biomechanically distinct and can be modeled in both in vivo and in vitro systems. The primary bTBI injury mechanism is associated with the response of brain tissue to the initial blast wave. Among the four mechanisms of bTBI, there is a remarkable lack of information regarding the mechanism of primary bTBI. On the other hand, 30 years of research on the medical application of shock waves (SWs) has given us insight into the mechanisms of tissue and cellular damage in bTBI, including both air-mediated and underwater SW sources. From a basic physics perspective, the typical blast wave consists of a lead SW followed by shock-accelerated flow. The resultant tissue injury includes several features observed in primary bTBI, such as hemorrhage, edema, pseudo-aneurysm formation, vasoconstriction, and induction of apoptosis. These are well-described pathological findings within the SW literature. Acoustic impedance mismatch, penetration of tissue by shock/bubble interaction, geometry of the skull, shear stress, tensile stress, and subsequent cavitation formation are all important factors in determining the extent of SW-induced tissue and cellular injury. In addition, neuropsychiatric aspects of blast events need to be taken into account, as evidenced by reports of comorbidity and of some similar symptoms between physical injury resulting in bTBI and the psychiatric sequelae of post-traumatic stress. Research into blast injury biophysics is important to elucidate specific pathophysiologic mechanisms of blast injury, which enable accurate differential diagnosis, as well as development of effective treatments. Herein we describe the requirements for an adequate experimental setup when investigating blast-induced tissue and cellular injury; review SW physics, research, and the importance of engineering validation (visualization/pressure measurement/numerical simulation); and, based upon our findings of SW-induced injury, discuss the potential underlying mechanisms of primary bTBI.

Anisotropy of Magnetic Susceptibility of Silicic Rocks From Quarries in the Vicinity of São Marcos, Rio Grande Do Sul, South Brazil: Implications for Emplacement Mechanisms.

NASA Astrophysics Data System (ADS)

Canon-Tapia, E.; Raposo, M. I. B.

2017-12-01

The Paraná-Etendeka Large Igneous Province includes felsic volcanic rocks whose mechanism of emplacement and location of their eruptive sources are controversial. Opening of several quarries of dimension stone near the city of Sao Marcos, Rio Grande do Sul, Brazil, offers a unique opportunity to study in detail some of those products. Here, we present the results of a study of the anisotropy of magnetic susceptibility (AMS) completed in some rocks that had been interpreted as the roots of volcanic conduits. Our results, and reexamination of the textural features of the rocks, lead to a reinterpretation that suggests that these rocks were emplaced subaerially, and involved assimilation and remelting of clastic components of previous lavas. The extremely high eruption temperatures of the lavas promoted the development of peperite-like textures and mixing patterns similar to those observed in plutonic environments. Due to the inferred conditions of emplacement, it is unlikely that the eruptive vents are located far from the area of study, therefore ruling out the long-travelled nature of these products.

Anisotropy of magnetic susceptibility of silicic rocks from quarries in the vicinity of São Marcos, Rio Grande do Sul, South Brazil: Implications for emplacement mechanisms

NASA Astrophysics Data System (ADS)

Cañón-Tapia, Edgardo; Raposo, M. Irene B.

2018-04-01

The Paraná-Etendeka Large Igneous Province includes acid volcanic rocks that can be found throughout its extension. Several aspects concerning those rocks remain controversial, including their mechanism of emplacement and location of their eruptive sources. Opening of several quarries of dimension stone near the city of Sao Marcos, Rio Grande do Sul, Brazil, offers a unique opportunity to study in detail the acid products. Here, we present the results of a study of the anisotropy of magnetic susceptibility (AMS) completed in some rocks that had been interpreted as the roots of volcanic conduits. Our results, and reexamination of the textural features of the rocks, lead to a reinterpretation that suggests that these rocks were emplaced subaerially, and involved assimilation and remelting of clastic components of previous products. Due to the inferred conditions of emplacement, it is unlikely that the eruptive vents are located far from the area of study, therefore ruling out the long-travelled nature of these products.

A BRIGHT SUBMILLIMETER SOURCE IN THE BULLET CLUSTER (1E0657-56) FIELD DETECTED WITH BLAST

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rex, Marie; Devlin, Mark J.; Dicker, Simon R.

2009-09-20

We present the 250, 350, and 500 {mu}m detection of bright submillimeter emission in the direction of the Bullet Cluster measured by the Balloon-borne Large-Aperture Submillimeter Telescope (BLAST). The 500 {mu}m centroid is coincident with an AzTEC 1.1 mm point-source detection at a position close to the peak lensing magnification produced by the cluster. However, the 250 {mu}m and 350 {mu}m centroids are elongated and shifted toward the south with a differential shift between bands that cannot be explained by pointing uncertainties. We therefore conclude that the BLAST detection is likely contaminated by emission from foreground galaxies associated with themore » Bullet Cluster. The submillimeter redshift estimate based on 250-1100 {mu}m photometry at the position of the AzTEC source is z{sub phot} = 2.9{sup +0.6}{sub -0.3}, consistent with the infrared color redshift estimation of the most likely Infrared Array Camera counterpart. These flux densities indicate an apparent far-infrared (FIR) luminosity of L{sub FIR} = 2 x 10{sup 13} L {sub sun}. When the amplification due to the gravitational lensing of the cluster is removed, the intrinsic FIR luminosity of the source is found to be L{sub FIR} <= 10{sup 12} L{sub sun}, consistent with typical luminous infrared galaxies.« less

Ultrafine Particle Distribution and Chemical Composition Assessment during Military Operative Trainings.

PubMed

Campagna, Marcello; Pilia, Ilaria; Marcias, Gabriele; Frattolillo, Andrea; Pili, Sergio; Bernabei, Manuele; d'Aloja, Ernesto; Cocco, Pierluigi; Buonanno, Giorgio

2017-05-30

(1) Background: The assessment of airborne particulate matter (PM) and ultrafine particles (UFPs) in battlefield scenarios is a topic of particular concern; (2) Methods: Size distribution, concentration, and chemical composition of UFPs during operative military training activities (target drone launches, ammunition blasting, and inert bomb impact) were investigated using an electric low-pressure impactor (ELPI+) and a scanning electron microscope (SEM), equipped with energy-dispersive spectroscopy (EDS); (3) Results: The median of UFPs, measured for all sampling periods and at variable distance from sources, was between 1.02 × 10³ and 3.75 × 10³ particles/cm³ for drone launches, between 3.32 × 10³ and 15.4 × 10³ particles/cm³ for the ammunition blasting and from 7.9 × 10³ to 1.3 × 10⁴ particles/cm³ for inert launches. Maximum peak concentrations, during emitting sources starting, were 75.5 × 10⁶ and 17.9 × 10⁶ particles/cm³, respectively. Particles from the drone launches were predominantly composed of silicon (Si), iron (Fe) and calcium (Ca), and those from the blasting campaigns by magnesium (Mg), sulphur (S), aluminum (Al), iron (Fe), barium (Ba) and silicon (Si); (4) Conclusions: The investigated sources produced UFPs with median values lower than other anthropogenic sources, and with a similar chemical composition.

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

Stone Quarrying, Crushing and Screening Facilities General Air Quality Permit Request for Coverage: Unimin Corporation - Unimin Flat Storage

EPA Pesticide Factsheets

Documents related to Request for Coverage under Stone Quarrying, Crushing and Screening Facilities General Permit, for the Unimin Corporation Silica Sand Rail Transloading Facility on the Fort Berhold Indian Reservation, North Dakota.

Assessment of Rock Slope Stability in Limestone Quarries in the Tournai's Region (Belgium) Using Structural Data

NASA Astrophysics Data System (ADS)

Tshibangu, Jean-Pierre; Deloge, K. Pierre-Alexandre; Deschamps, Benoît; Coudyzer, Christophe

The Tournais region is characterised by famous outcrops of carboniferous limestone which is mined out for cement and raw material production. The four main quarries found in the Region, i.e. Gaurain-Ramecroix, Milieu, Antoing and Lemay; are owned by the three main cement producers in Belgium: Italcimenti, Holcim and CBR. The global production of limestone is about 20 millions tons per year, giving big pits with depths up to 150 m. With the growth of the pits, the quarries are approaching each other leading to the problem of managing the reserves contained in the separating walls and their mechanical stability. The limestone deposit is composed of different seams having varying thickness, chemical com- position and even mechanical properties. The deposit has an overall horizontal dip and is intersected by two main sets of discontinuities with a spacing of about 10 m or less. It is also crossed by a set of east to west faults but the quarries are implanted in the in between areas, so to not be crossed by these faults. The layers and specially the shallow ones are characterised by a typical karstic weathering giving open or filled cavities. This paper presents the global work quarried out in order to study the stability of the Lemays quarry. First a description of the orientation and spacing of discontinuities is presented, and an attempt made to correlate to the development of weathering. Mechanical laboratory tests have been performed and a qualification of the rock mass assessed. A coupled approach is then presented using a mining planning analysis and mechanical simulation (i.e. Finite Element method).

Revegetation in abandoned quarries with landfill stabilized waste and gravels: water dynamics and plant growth - a case study

NASA Astrophysics Data System (ADS)

Zhang, Cheng-liang; Feng, Jing-jing; Rong, Li-ming; Zhao, Ting-ning

2017-11-01

Large amounts of quarry wastes are produced during quarrying. Though quarry wastes are commonly used in pavement construction and concrete production, in situ utilization during ecological restoration of abandoned quarries has the advantage of simplicity. In this paper, rock fragments 2-3 cm in size were mixed with landfill stabilized waste (LSW) in different proportions (LSW : gravel, RL), which was called LGM. The water content, runoff and plant growth under natural precipitation were monitored for 2 years using a runoff plot experiment. LGM with a low fraction of LSW was compacted to different degrees to achieve an appropriate porosity; water dynamics and plant growth of compacted LGM were studied in a field experiment. The results showed the following: (1) LGM can be used during restoration in abandoned quarries as growing material for plants. (2) RL had a significant effect on the infiltration and water-holding capacity of LGM and thus influenced the retention of precipitation, water condition and plant growth. LGM with RL ranging from 8:1 to 3:7 was suitable for plant growth, and the target species grew best when RL was 5:5. (3) Compaction significantly enhanced water content of LGM with a low RL of 2:8, but leaf water content of plants was lower or unchanged in the more compacted plots. Moderate compaction was beneficial to the survival and growth of Robinia pseudoacacia L. Platycladus orientalis (L.) Franco and Medicago sativa L. were not significantly affected by compaction, and they grew better under a high degree of compaction, which was disadvantageous for the uppermost layer of vegetation.

Using Building Seismic Strong-Motion Data to Quantify Urban Blast Pressure Fields

NASA Astrophysics Data System (ADS)

Massari, A.; Kohler, M. D.; Heaton, T. H.; Kanamori, H.; Hauksson, E.; Clayton, R. W.; Guy, R.; Bunn, J.; Chandy, M.

2015-12-01

The use of building vibrations to measure blast wave propagation in a city is examined in this case study. The Exxon Mobil Corp. oil refinery in Torrance, California experienced an explosion on February 18, 2015 causing ground shaking equivalent to a magnitude 1.9 earthquake. The impulse response for the source was computed from Southern California Seismic Network data for a multi-orthogonal force system with a value of 2×105 kN vertically downward. The pressure wave excited by the explosion traveled through the city of Los Angeles, and was detected by a dense accelerometer array in a 52-story building also in downtown Los Angeles 22.8 km from the explosion. The array is part of the Community Seismic Network (CSN) and consists of three-component class-C MEMs sensors located on each floor of the building. The detection was verified by the nearly simultaneous arrival times of acceleration pulses on multiple floors of the building, corresponding to an average wave speed near the speed of sound in air. The pressure wave peak magnitude from the air blast was determined using accelerometer data collected on every floor of the building coupled with the elastic response of the structure as a whole. . Making use of high-fidelity finite element modeling of the building validated by previous low-level seismicity and ambient noise data, a procedure is outlined for pressure wave detection and quantification on well instrumented buildings. This case study for a 52 story building, instrumented by the CSN, acts as a proxy for blast wave quantification in dense urban environments. This type of information can be used to understand the flow of blast waves through a cityscape as well as enhance procedures for estimating blast source magnitude. Better understanding of the propagation of pressure waves in urban environments will lead to the development of improved countermeasures in those environments.

Is there evidence for an acoustic signal at IMS infrasound stations from the North Korean event of 12 May 2010?

NASA Astrophysics Data System (ADS)

Koch, K.; Pilger, C.

2016-12-01

Over the last two years more and more evidence has been presented that a small seismic event had occurred in North Korea on 12 May 2010. Most recent work has concluded that the event shows earthquake-like features when applying event identification methods based on regional phase amplitude ratios. These findings are in contrast to previous hypotheses and identification studies which claimed that low-yield nuclear testing had been carried out. Some of these studies were based solely on radionuclide and noble gas detections found at International Monitoring System (IMS) stations as well as at national facilities. Turning to another technology, it has been shown in several studies that underground nuclear tests carried out at the Punggye-ri test site in North Korea have produced infrasound signatures at the closest IMS stations I45RU and I30JP and at national infrasound stations in South Korea. In particular this holds for the tests carried out in 2009, 2013 and 2016. For the 2013 test infrasound arrivals have been included in the Reviewed Event Bulletin (REB) issued by the International Data Center of CTBTO. Based on this experience an effort was undertaken to analyze infrasound data from these IMS stations and to search for signals that may be associated to the 12 May 2010 event. While it is not expected to obtain such a signal for an earthquake source at depth, as would not be expected as well for a buried explosion source of rather small magnitude, the analysis of I45RU and I30JP data suggests a very weak arrival as obtained from frequency-wavenumber analysis showing parameters similar to those obtained for the announced tests. If the features found are indeed not artifacts then one could speculate that (1) the event of concern may not be an earthquake, even though it exhibits seismic signal characteristics causing it to be classified as an earthquake, or (2) the detections may be related to incidental blasting activity in nearby quarries. Propagation modeling of infrasound waves is being carried out to investigate the ducting behavior for the signals observed at regional infrasound stations.

HangOut: generating clean PSI-BLAST profiles for domains with long insertions.

PubMed

Kim, Bong-Hyun; Cong, Qian; Grishin, Nick V

2010-06-15

Profile-based similarity search is an essential step in structure-function studies of proteins. However, inclusion of non-homologous sequence segments into a profile causes its corruption and results in false positives. Profile corruption is common in multidomain proteins, and single domains with long insertions are a significant source of errors. We developed a procedure (HangOut) that, for a single domain with specified insertion position, cleans erroneously extended PSI-BLAST alignments to generate better profiles. HangOut is implemented in Python 2.3 and runs on all Unix-compatible platforms. The source code is available under the GNU GPL license at http://prodata.swmed.edu/HangOut/. Supplementary data are available at Bioinformatics online.

On the way of Friuli "yellow villages": the use of a calcareous-dolomitic sandstone in the surroundings of the quarrying area through the centuries.

NASA Astrophysics Data System (ADS)

Frangipane, Anna

2017-04-01

The role of local stone building material in cultural and technological heritage is based on the definition of the area of use, as related to ancient transportation networks, allowing the movement of heavy blocks from the quarries to the building sites. It is the case of the result of several surveys carried out for the detection of the architectural elements, dating from Middle Age to 20th century, made of a yellowish calcareous-dolomitic sandstone, which have been found, hidden among renovated buildings and new construction, in Friuli region (NE Italy). on the way between the quarrying piedmont western area and the towns of Udine and Spilimbergo. Starting from the definition of the quarrying area, the contribution give notice of such architectural elements (frames, columns, …), both in vernacular architecture and in relevant buildings, putting in evidence the period of their realisation and their technological features.

Glacial Erosion Driven by Seasonal Shifts in Meltwater Drainage

NASA Astrophysics Data System (ADS)

Ugelvig, S. V.; Egholm, D. L.

2017-12-01

Subglacial erosion processes, like abrasion and quarrying, have been studied for decades. While models for abrasion clearly points to sliding speed as a primary control on abrasion rates, quarrying rates are thought to be governed by more complex combinations of sliding speed, effective pressure, bedrock slope and short-term water pressure fluctuations. Early models for quarrying focused on the deviatoric stress needed for growth of small isolated cracks in otherwise homogeneous intact bedrock. The rate-limiting factor for quarrying was thus the subcritical crack growth. Later studies have included effects of pre-existing fractures in the bedrock that weaken the rock. Here the strength distribution in the rock is based on the assumption that larger rock bodies have lower strength, because they have a higher probability of containing a weak fracture. However, this approach has been hampered by the assumption of steady-state cavity configuration. Here we attempt to combine previous model efforts in a model that tracks the temporal evolution of cavities while including a statistical treatment of bedrock strength. Using a two-dimensional finite-difference model, we simulate the spatial and temporal evolution of the hydrological system at the base of a glacier, while simultaneously computing rates of abrasion and quarrying. Cavity lengths and channel cross-sections evolve through time, which allow us to study how temporal shifts in ice-bed contact area and deviatoric stress influence quarrying rates over the course of a year. Furthermore, we use the temporal evolution of contact area between ice and bed to predict basal sliding speed and scale abrasion rates. Our results suggest that ice-bed contact area is a key variable in controlling sliding speed and rates of glacial erosion on seasonal time scales, where the subglacial drainage system reorganizes to accommodate the variations in surface melt rates. However, on diurnal timescales cavities and channels cannot adjust to the relatively rapid changes in meltwater input, which causes large fluctuations in water pressure. This in turn elevates the deviatoric stress in the bedrock and pressure fluctuations are thus on diurnal timescales found to dictate quarrying rates as well as abrasion rates.

Compilation and preliminary interpretation of hydrologic data for the Weldon Spring radioactive waste-disposal sites, St Charles County, Missouri; a progress report

USGS Publications Warehouse

Kleeschulte, M.J.; Emmett, L.F.

1986-01-01

The Weldon Spring Chemical Plant is located just north of the drainage divide separating the Mississippi River and the Missouri River in St. Charles County, Missouri. From 1957 to 1966 the plant converted uranium-ore concentrates and recycled scrap to pure uranium trioxide, uranium tetrafluoride, and uranium metal. Residues from these operations were pumped to four large pits that had been excavated near the plant. Small springs and losing streams are present in the area. Water overlying the residue in the pits has a large concentration of dissolved solids and a different chemical composition compared to the native groundwater and surface water. This difference is indicated by the concentrations of calcium, sodium, sulfate, nitrate, fluoride, uranium, radium, lithium, molybdenum, strontium, and vanadium, all of which are greater than natural or background concentrations. Water from Burgermeister Spring, located about 1.5 miles north of the chemical plant area, contains uranium and nitrate concentrations greater than background concentrations. Groundwater in the shallow bedrock aquifer moves northward from the vicinity of the chemical plant toward Dardenne Creek. An abandoned limestone quarry several miles southwest of the chemical plant also has been used for the disposal of radioactive waste and rubble. Groundwater flow from the quarry area is southward through the alluvium, away from the quarry and toward the Missouri River. The St. Charles County well field is located in the Missouri River flood plain near the quarry and the large yield wells are open to the Missouri River alluvial aquifer. Water from a well 4,000 ft southeast of the quarry was analyzed; there was no indication of contamination from the quarry. Additional water quality and water level data are needed to determine if water from the quarry moves toward the well field. Observation wells need to be installed in the area between the chemical plant, pits, and Dardenne Creek. The wells would be used to provide access for measurements of depth to ground water and for the collection of water samples from the shallow bedrock aquifer. (Lantz-PTT)

Quantification of Reduction in Forced Vital Capacity of Sand Stone Quarry Workers

PubMed Central

Singh, Suresh Kumar; Chowdhary, G. R.; Chhangani, V. D.; Purohit, Gopal

2007-01-01

This study assessed the reduction in forced vital capacity of lungs of sand stone quarry workers exposed to high respirable suspended particulate concentration. The sand stone quarry workers are engaged in different type of activities like drilling, loading and dressing. These different working places have different concentration of RSPM and these workers are exposed to different concentration of RSPM. It is found that exposure duration and exposure concentrations are main factors responsible to damage respiratory tract of worker. It is also revealed from the study that most of the workers are suffering from silicosis if the exposure duration is more than 15 years. PMID:18180540

Specifiers Properties Information Exchange (SPie): Minimum Building Information Model (BIM) Object Definitions

DTIC Science & Technology

2013-03-01

Weave Welding Method Wheel Assembly Wind Load Wind Loads Wind Uplift Resistance Wind Uplift Resistance Class Window Category Window Finish Window... wind - blast Elongation UFGS 2.1 percent Insert Value Visual Defects UFGS 2.1 n/a Insert Value ERDC/CERL CR-13-1 39 Attribute Source...Sustainability COBie Guide n/a insert reqts FRP Strengthening UFGS 1.2 n/a seismic - wind - blast Elongation UFGS 2.2 percent Insert Value Tensile

Isotopic Fingerprints of Iron-Cyanide Complexes in the Environment.

PubMed

Mansfeldt, Tim; Höhener, Patrick

2016-07-19

Tracing the origin of iron-cyanide complexes in the environment is important because these compounds are potentially toxic. We determined the stable isotopic compositions of cyanide-carbon (CCN) and cyanide-nitrogen (NCN) in 127 contaminated solids and 11 samples of contaminated groundwater from coal carbonization sites, blast furnace operations, and commercial cyanide applications. Coal-carbonization-related cyanides had unique high mean δ(13)CCN values of -10.5 ± 3.5‰ for the solids and -16.1 ± 1.2‰ for the groundwater samples, while the values for blast furnace sludge (-26.9 ± 1.5‰), commercial cyanides (-26.0 ± 3.0‰), and their corresponding groundwaters were significantly lower. Determination of δ(13)CCN is a promising tool for identifying the source of cyanide contamination. However, for coal carbonization sites, historical research into the manufacturing process is necessary because a nonconventional gas works site exhibited exceptionally low δ(13)CCN values of -22.7 ± 1.7‰. The δ(15)NCN values for samples related to coal carbonization and blast furnaces overlapped within a range of +0.1 to +10.3‰, but very high δ(15)NCN values seemed to be indicative for a cyanide source in the blast furnace. In contrast, commercial cyanides tend to have lower δ(15)NCN values of -5.6 to +1.9‰ in solids and -0.5 to +3.0‰ in the groundwater.

Quarry waste management and recovery: first results connected to Carrara marble ravaneti (Italy)

NASA Astrophysics Data System (ADS)

Antonella Dino, Giovanna; Chiappino, Claudia; Rossetti, Piergiorgio

2017-04-01

Quarry waste (QW) represents a huge economic and environmental issue, due to loss of resources and to economic and environmental costs connected to waste management and landfilling activities. In many cases, valuable Raw Materials (RM) and Secondary Raw Materials (SRM) can be supplied by enhancing the QW recovery. In Italy large amounts of QW have been and still are dumped: such materials, if their quality (chemical, mineralogical, physical characteristics) and quantity are adequate, and if the impacts connected to their management are positive, can represent a valuable resource for SRM exploitation. Several dimension stone quarries have been and are interested by researches as for QW exploitation. Some researches show positive results, which are the basis for QW recovery (both from waste streams and from quarry dumps exploitation): a noticeable example is represented by Carrara marble waste. The Carrara quarry basin is characterized by ca. one hundred quarries for colored and white marble exploitation. The waste production can be summarized in: 80 Mm3 waste present in old quarry dumps (Ravaneti) and 3 Mm3/y of waste stream from quarrying activities. At present only 0.5 Mm3/y of QW is exploited for SRM production, causing a huge loss of resource. This has been the background for a preliminary research, on Carrara marble Ravaneti characterization, which was carried out thanks to the close cooperation between University of Torino, Società Apuana Marmi srl, and SET srl. In 2015, two QW dumping areas, Calocara and Lorano, were selected as representative for sampling activities. Three main sample categories were individuated based on granulometry (0.5-4 mm, 0-25 mm, 0-150 mm) to be characterized (size distribution, density, Atterberg limits, Los Angeles test, freezing and heat tests, flat and shape indexes, geochemistry, mineralogy). The results obtained are promising: the physical characterization shows an attitude for Carrara QW to be recovered as crushed materials for embankments and armour stone. Furthermore, the mineralogical and geochemical analyses show that these materials, being composed of nearly pure CaCO3, could find a proper application in high value products, as filler for paper, rubber, paint, plastic, etc. These data need to be confirmed by other analyses, thus a systematic characterization of QW present in the different quarry dumps is going to be programmed. R&D is strategic to solve problems connected to QW and landscape management. The cooperation between private Companies, Research Centers and Local Authorities is fundamental to reach the target, in terms of experimentation of new products (for civil works and infrastructure, building industry, agronomy, high-tech, etc.). Furthermore, if the stone industry aims at guaranteeing the systematic and convenient SRM recovery from QW, a change in exploitation and working activities has to be planned (eg. selection of the potential SRMs; dedicated stock areas for selected SRM; proper treatments depending on the kinds of reuse; treatment-activity protocols to produce each new product, etc.).

Hydrogeological features conditioning trophic levels of quarry lakes in western Po plain (north-western Italy)

NASA Astrophysics Data System (ADS)

De Luca, Domenico Antonio; Castagna, Sara; Lasagna, Manuela

2013-04-01

Quarry lakes occur in plains areas due to the extraction of alluvial sand and gravel used for grout and concrete in the construction industry. Excavation depths can reach and intersect the groundwater surface, thus creating a lake. Because of the need to optimize efficiency, the number of active open pit mines has increased in recent years; consequently, the global number of pit lakes will increase in coming decades (Castendyk and Eary 2009; Klapper and Geller 2001; Castro and Moore 2000). Similar to natural lakes, pit lakes are subject to eutrophication process, both during and after quarrying activity; during mining activity, the eutrophic level is strongly controlled by the excavation method. In the Piedmont territory (north-western Italy) there are 70 active quarry lakes, corresponding to approximately 0.1% of the entire plain area. Quarry lakes, located primarily along the main rivers occur in alluvial deposits of the plain area and have average depths between 20 and 30 m (maximum of 60 m deep) and surface areas between 3 and 30 hectares (Castagna 2008). The present study describes the trophic status of 23 active quarry lakes in the Piedmont plain that were evaluated by applying classifications from scientific literature. Currently, the majority of the studied quarry lakes may be defined as mesotrophic or eutrophic according to the trophic state classifications. Based on historic data, lake trophic levels have increased over time, during active mining. At the end of mining activity, further deterioration of water quality was expected, especially for smaller lakes with minimal oxygen stratification and higher levels of nutrients and algal growth. In addition, the paper focuses on the pit lake water quality and pit dimension; From an environmental perspective the excavation of quarry lakes with an appreciable size will likely result in a better safeguard of water quality and enhanced possibilities for lake end use after the cessation of mining. Piedmont quarry lakes, for the most part, have rather large depths (over 20 m), and moreover, unlike natural lakes, this type of lake is not influenced by sewage inputs that are often a primary cause of eutrophication in natural lakes. It was shown that, in Piedmont, lakes with a larger depth and volume generally had a lower tendency towards eutrophication. References Castendyk D, Eary T (2009). The nature and global distribution of pit lakes. In, Mine Pit Lakes: Characteristics, Predictive Modeling, and Sustainability Castendyk, D.; Eary, T. and Park, B. (eds.) Society for Mining Engineering (SME), Colorado, USA, 1-11pp. Klapper H, Geller W (2001) Water quality management of mining lakes - a new field of applied hydrobiology. Acta Hydrochim Hydrobiol, 29: 363-374 Castro JM, Moore JN (2000) Pit lakes: their characteristics and the potential for their remediation. Environ Geol, 39(11):1254-1260 Castagna S (2008) Studio delle problematiche idrogeologiche nelle attività estrattive sottofalda per materiali granulari. Ph.D. Thesis.

Plasma Sheet Source and Loss Processes

NASA Technical Reports Server (NTRS)

Lennartsson, O. W.

2000-01-01

Data from the TIMAS ion mass spectrometer on the Polar satellite, covering 15 ev/e to 33 keV/e in energy and essentially 4(pi) in view angles, are used to investigate the properties of earthward (sunward) field-aligned flows of ions, especially protons, in the plasma sheet-lobe transition region near local midnight. A total of 142 crossings of this region are analyzed at 12-sec time resolution, all in the northern hemisphere, at R(SM) approx. 4 - 7 R(sub E), and most (106) in the poleward (sunward) direction. Earthward proton flows are prominent in this transition region (greater than 50% of the time), typically appearing as sudden "blasts" with the most energetic protons (approx. 33 keV) arriving first with weak flux, followed by protons of decreasing energy and increasing flux until either: (1) a new "blast" appears, (2) the flux ends at a sharp boundary, or (3) the flux fades away within a few minutes as the mean energy drops to a few keV. Frequent step-like changes (less than 12 sec) of the flux suggest that perpendicular gradients on the scale of proton gyroradii are common. Peak flux is similar to central plasma sheet proton flux (10(exp 5) - 10(exp 6)/[cq cm sr sec keV/e] and usually occurs at E approx. 4 - 12 keV. Only the initial phase of each "blast" (approx. 1 min) displays pronounced field-alignment of the proton velocity distribution, consistent with the time-of-flight separation of a more or less isotropic source distribution with df/d(nu) less than 0. The dispersive signatures are often consistent with a source at R(SM) less than or equal to 30 R(sub E). No systematic latitudinal velocity dispersion is found, implying that the equatorial plasma source is itself convecting. In short, the proton "blasts" appear as sudden local expansions of central plasma sheet particles along reconfigured ("dipolarized") magnetic field lines.

The growth of pines germinated from woodchip mulch in restored soils from semiarid SE Spain quarries is enhanced by organic amendments

NASA Astrophysics Data System (ADS)

Luna Ramos, Lourdes; Miralles, Isabel; Lázaro-Suau, Roberto; Solé-Benet, Albert

2017-04-01

The use of pine woodchips in soil restoration in calcareous quarries is a relatively low-cost mulching technique to improve soil water conservation and decrease soil erosion, contributing to improve soil quality. Besides these two important effects, woodchip mulch is also a potential source of seeds which can germinate if environmental conditions during earlier stages are adequate. Pine germination has been observed in experimental plots treated with pine woodchips used as mulch in one of the driest regions in Europe (SE Spain). This side-effect provided an interesting opportunity to analyse the influence of topsoil and two organic wastes (compost from domestic organic waste and sewage sludge from urban water treatment plant) in mine soils on the germinated pines (Pinus halepensis Mill.) and the plant cover (revegetated native plants and spontaneous vegetation). Number, height and basal diameter of pines and the total plant cover were measured 6 years after the applications of topsoil and organic amendments. Results showed that organic wastes increased the pine growth and the total plant cover which could favour in turn the physico-chemical soil properties and its quality in the medium-long term. However, organic amendments negatively influencing the number of germinated pines. The likely growth of pine seedlings derived from the pine cones which come with pine woodchips used as mulch, when enhanced by organic amendments, adds a positive value in quarry restoration even under very dry climatic conditions. However, it is necessary to continue monitoring the development of vegetation to form a more precise idea about whether the development of the pines is globally beneficial, since the pines could outcompete the local native plants.

Oscar Renda Contracting Inc. Navajo Nation Crushing/Screening Operation: Coverage Under General Air Quality Permit for Stone Quarrying, Crushing and Screening Facilities

EPA Pesticide Factsheets

Documents related to approved request for coverage under the Stone Quarrying, Crushing and Screening Facilities General Permit for Oscar Renda Contracting Inc. Navajo Nation Crushing/Screening Operation located in McKinley and San Juan Counties, NM.

GT0 Explosion Sources for IMS Infrasound Calibration: Charge Design and Yield Estimation from Near-source Observations

NASA Astrophysics Data System (ADS)

Gitterman, Y.; Hofstetter, R.

2014-03-01

Three large-scale on-surface explosions were conducted by the Geophysical Institute of Israel (GII) at the Sayarim Military Range, Negev desert, Israel: about 82 tons of strong high explosives in August 2009, and two explosions of about 10 and 100 tons of ANFO explosives in January 2011. It was a collaborative effort between Israel, CTBTO, USA and several European countries, with the main goal to provide fully controlled ground truth (GT0) infrasound sources, monitored by extensive observations, for calibration of International Monitoring System (IMS) infrasound stations in Europe, Middle East and Asia. In all shots, the explosives were assembled like a pyramid/hemisphere on dry desert alluvium, with a complicated explosion design, different from the ideal homogenous hemisphere used in similar experiments in the past. Strong boosters and an upward charge detonation scheme were applied to provide more energy radiated to the atmosphere. Under these conditions the evaluation of the actual explosion yield, an important source parameter, is crucial for the GT0 calibration experiment. Audio-visual, air-shock and acoustic records were utilized for interpretation of observed unique blast effects, and for determination of blast wave parameters suited for yield estimation and the associated relationships. High-pressure gauges were deployed at 100-600 m to record air-blast properties, evaluate the efficiency of the charge design and energy generation, and provide a reliable estimation of the charge yield. The yield estimators, based on empirical scaled relations for well-known basic air-blast parameters—the peak pressure, impulse and positive phase duration, as well as on the crater dimensions and seismic magnitudes, were analyzed. A novel empirical scaled relationship for the little-known secondary shock delay was developed, consistent for broad ranges of ANFO charges and distances, which facilitates using this stable and reliable air-blast parameter as a new potential yield estimator. The delay data of the 2009 shot with IMI explosives, characterized by much higher detonation velocity, are clearly separated from ANFO data, thus indicating a dependence on explosive type. This unique dual Sayarim explosion experiment (August 2009/January 2011), with the strongest GT0 sources since the establishment of the IMS network, clearly demonstrated the most favorable westward/eastward infrasound propagation up to 3,400/6,250 km according to appropriate summer/winter weather pattern and stratospheric wind directions, respectively, and thus verified empirically common models of infrasound propagation in the atmosphere.

The use of vibration monitoring to record the blasting works impact on buildings surrounding open-pit mines

NASA Astrophysics Data System (ADS)

Sołtys, Anna; Pyra, Józef; Winzer, Jan

2018-04-01

Environmental protection law and geological and mining law require the mineral mining plant to protect its surroundings from the effects of mining operations. This also applies to the negative impact of vibrations induced by blasting works on people and construction facilities. Effective protection is only possible if the level of this impact is known, therefore it is necessary to record it. The thesis formulated in this way has been and continues to be the guiding principle of the research works carried out in the AGH Laboratory of Blasting Work and Environmental Protection. As a result of these works are procedures for conducting preventive activities by open-pit mines in order to minimize the impact of blasting on facilities in the surrounding area. An important element of this activity is the monitoring of vibrations in constructions, which is a source of knowledge for excavation supervisors and engineers performing blasting works, thus contributing to raising the awareness of the responsible operation of the mining plant. Developed in the Laboratory of the Mine's Vibration Monitoring Station (KSMD), after several modernizations, it became a fully automated system for monitoring and recording the impact of blasting works on the surrounding environment. Currently, there are 30 measuring devices in 10 open-pit mines, and additional 8 devices are used to provide periodic measurement and recording services for the mines concerned.

Waste plastics as supplemental fuel in the blast furnace process: improving combustion efficiencies.

PubMed

Kim, Dongsu; Shin, Sunghye; Sohn, Seungman; Choi, Jinshik; Ban, Bongchan

2002-10-14

The possibility of using waste plastics as a source of secondary fuel in a blast furnace has been of recent interest. The success of this process, however, will be critically dependent upon the optimization of operating systems. For instance, the supply of waste plastics must be reliable as well as economically attractive compared with conventional secondary fuels such as heavy oil, natural gas and pulverized coal. In this work, we put special importance on the improvement of the combustibility of waste plastics as a way to enhance energy efficiency in a blast furnace. As experimental variables to approach this target, the effects of plastic particle size, blast temperature, and the level of oxygen enrichment were investigated using a custom-made blast model designed to simulate a real furnace. Lastly, the combustion efficiency of the mixture of waste plastics and pulverized coal was tested. The observations made from these experiments led us to the conclusion that with the increase of both blast temperature and the level of oxygen enrichment, and with a decrease in particle size, the combustibility of waste polyethylene could be improved at a given distance from the tuyere. Also it was found that the efficiency of coal combustion decreased with the addition of plastics; however, the combustion efficiency of mixture could be comparable at a longer distance from the tuyere.

Statistical Evaluation of Turkey Earthquake Cataloque: A Case study (1900-2015)

NASA Astrophysics Data System (ADS)

Kalafat, Dogan

2016-04-01

In this study, Turkey earthquake catalog of the events within the time period of 1900-2015 prepared by Boǧaziçi University Kandilli Observatory and Earthquake Research Institute is analyzed. The catalog consists of earthquakes occurred in Turkey and surrounding area (32o-45oN/23o-48oE). The current earthquake catalog data has been checked in two aspects; the time dependent variation and compliance for different regions. Specifically the data set prior to 1976 was found deficient. In total, 7 regions were evaluated according to the tectonic specifications and data set. In this study for every region original data were used without any change; b- values, a- values, Magnitude of completeness (Mc) were calculated. For the calculation of b- values focal depth was selected as h= 0-50 km. One of the important complications for the seismic catalogs is discriminating real (natural) seismic events from artificial (unnatural) seismic events. Therefore within the original current catalog events especially artificial quarry blasts and mine blasts have been separated by declustering and dequarry methods. Declustering process eliminates induced earthquakes especially occurred in thermal regions, large water basins, mine regions from the original catalogs. Current moment tensor catalog prepared by Kalafat, 2015 the faulting type map of the region was prepared. As a result, for each region it is examined if there is a relation between fault type and b- values. In this study, the hypothesis of the relation between previously evaluated and currently ongoing extensional, compression, strike-slip fault regimes in Turkey and b- values are tested one more time. This study was supported by the Department of Science Fellowship and Grant programs (2014-2219) of TUBITAK (The Scientific and Technological Research Councilof Turkey). It also encourages the conduct of the study and support the constructive contributionthat Prof.Dr. Nafi TOKSÖZ to offer my eternal gratitude.

Thirty years of seismic network recording in South Australia: Selected results

NASA Astrophysics Data System (ADS)

Greenhalgh, S. A.; Love, D.; Sinadinovski, C.

1994-11-01

The year 1993 marks 30 years of seismic network recording of earthquakes in South Australia. The network currently comprises 17 short-period instruments, of which six use digital recording and five employ triaxial sensors. Approximately 350 earthquakes are located within the State each year using a computerized seismic analysis system developed by the Phillip Institute of Technology. A duration-based magnitude scale, equivalent to the Richter M(sub L) scale, has been developed for most stations. The pre-network (historical) record of earthquake activity in South Australia dates back to 1837. Epicenters are available for just 45 earthquakes. Of these, ten are of magnitude five or greater. The instrumental data over the last 30 years show a similar trend in epicentral pattern to the historical earthquakes, with the major zones being the Flinders Ranges, Eyre Peninsula and the Southeast. There have been 40 earthquakes of magnitude four or greater since 1963, the largest earthquake being of magnitude six in the Musgrave Ranges during 1986. Mine and quarry blasts within the State have been useful in calibration of the network, both in terms of hypocentral location and amplitude studies. The explosions have also furnished valuable information on the crustal velocity distribution. Epicentral co-ordinates of mine blasts are generally good to within 3-5 km. The explosions yield Richter magnitudes of one (charge size 1 or 2 tons) to 2.5 (charge size 50 tons). The crustal S waves, used in earthquake magnitude determinations, exhibit an amplitude-distance decay coefficient of 1.2. The P-wave velocity function of the crust increases non-linearly with depth, from about 5.0 km /s near the surface to 6.4 km /s at 20 km depth, where the gradient reduces, with the velocity reaching a value of about 7.4 km /s at a depth of 40 km.

Seismic Monitoring of Stability of Unique Historical Buildings in the Czech Republic

NASA Astrophysics Data System (ADS)

Broz, M.; Strunc, J.; Buben, J.

2008-05-01

The persistence of unique Historical Buildings is restricted due to weathering of construction material enhanced by meteorological processes such as storms, driving rain and temperature variations beneath the freezing point. Dynamic forces endangering the mechanical stability of exposed elements of building structures could be caused also by impacts of seismic waves. The long-time decrease of earthquake resistance is monitored using empirical functions of seismic response. This method is based on evaluation the co-spectra of exciting and forced vibrations of foundations and the structure elements in question. This poster notifies three examples of utilization of this method as follows: 1) In the course of renovating the St. Barbora temple in the Kutná Hora village, the vibrations caused by meteorological processes, supersonic aircraft transit and blasting in quarries have been evaluated. After completing the renovation of endangered spire elements, the local maximum of co-spectral function at 4Hz was shifted to 7Hz and the function approached more likely a wide-band course. 2) In the course of installation of the third bell in the bell tower of the of the Sázava monastery, the co-spectra of forced vibrations of tower walls were monitored and a more convenient time-function of bell clang was adjusted. 3) In connection with the construction of a highway tunnel in the 1,4 km distance from the St. Vit cathedral in the Praha-Hradèany castle, the long-term schedule of motoring seismic vibrations was started. In the course of driving the tunnels, the mili-sec blasting of charges up to 5 kg is used. Seismic vibrations are recorded by pickups situated on the subsoil and on the voussoir arch. The digital multichannel seismic recording apparatus (256 samples per sec) is equipped for continuous telemetric data transfer and automated evaluation. (Grant Foundation of the Czech Republic, 103/07/1522).

Blast dynamics at Mount St Helens on 18 May 1980

USGS Publications Warehouse

Kieffer, S.W.

1981-01-01

At 8.32 a.m. on 18 May 1980, failure of the upper part of the north slope of Mount St Helens triggered a lateral eruption ('the blast') that devastated the conifer forests in a sector covering ???500 km2 north of the volcano. I present here a steady flow model for the blast dynamics and propose that through much of the devastated area the blast was a supersonic flow of a complex multiphase (solid, liquid, vapour) mixture. The shape of the blast zone; pressure, temperature, velocity (Mach number) and density distributions within the flow; positions of weak and strong internal shocks; and mass flux, energy flux, and total energy are calculated. The shape of blast zone was determined by the initial areal expansion from the reservoir, by internal expansion and compression waves (including shocks), and by the density of the expanding mixture. The pressure within the flow dropped rapidly away from the source of the blast until, at a distance of ???11 km, the flow became underpressured relative to the surrounding atmosphere. Weak shocks within the flow subparallel to the east and west margins coalesced at about this distance into a strong Mach disk shock, across which the flow velocities would have dropped from supersonic to subsonic as the pressure rose back towards ambient. The positions of the shocks may be reflected in differences in the patterns of felled trees. At the limits of the devastated area, the temperature had dropped only 20% from the reservoir temperature because the entrained solids thermally buffered the flow (the dynamic and thermodynamic effects of the admixture of the surrounding atmosphere and the uprooted forest and soils into the flow are not considered). The density of the flow decreased with distance until, at the limits of the blast zone, 20-25 km from the volcano, the density became comparable with that of the surrounding (dirty) atmosphere and the flow became buoyant and ramped up into the atmosphere. According to the model, the mass flux per unit area at the source was 0.6 ?? 104 g s-1 cm-2 and the energy flux per unit area was 2.5 MW cm-2. From the measured total ejected mass, 0.25 ?? 1015 g, the total energy released during the eruption was 1024 erg or 24 megatons. The model, triggering of the eruption and the transition from unsteady to steady flow, and applications to eyewitness observations and atmospheric effects are discussed in ref. 1. ?? 1981 Nature Publishing Group.

Apollo: a community resource for genome annotation editing

PubMed Central

Ed, Lee; Nomi, Harris; Mark, Gibson; Raymond, Chetty; Suzanna, Lewis

2009-01-01

Summary: Apollo is a genome annotation-editing tool with an easy to use graphical interface. It is a component of the GMOD project, with ongoing development driven by the community. Recent additions to the software include support for the generic feature format version 3 (GFF3), continuous transcriptome data, a full Chado database interface, integration with remote services for on-the-fly BLAST and Primer BLAST analyses, graphical interfaces for configuring user preferences and full undo of all edit operations. Apollo's user community continues to grow, including its use as an educational tool for college and high-school students. Availability: Apollo is a Java application distributed under a free and open source license. Installers for Windows, Linux, Unix, Solaris and Mac OS X are available at http://apollo.berkeleybop.org, and the source code is available from the SourceForge CVS repository at http://gmod.cvs.sourceforge.net/gmod/apollo. Contact: elee@berkeleybop.org PMID:19439563

Apollo: a community resource for genome annotation editing.

PubMed

Lee, Ed; Harris, Nomi; Gibson, Mark; Chetty, Raymond; Lewis, Suzanna

2009-07-15

Apollo is a genome annotation-editing tool with an easy to use graphical interface. It is a component of the GMOD project, with ongoing development driven by the community. Recent additions to the software include support for the generic feature format version 3 (GFF3), continuous transcriptome data, a full Chado database interface, integration with remote services for on-the-fly BLAST and Primer BLAST analyses, graphical interfaces for configuring user preferences and full undo of all edit operations. Apollo's user community continues to grow, including its use as an educational tool for college and high-school students. Apollo is a Java application distributed under a free and open source license. Installers for Windows, Linux, Unix, Solaris and Mac OS X are available at http://apollo.berkeleybop.org, and the source code is available from the SourceForge CVS repository at http://gmod.cvs.sourceforge.net/gmod/apollo.

Analysis of medieval limestone sculpture from southwestern France and the Paris Basin by NAA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holmes, L.; Harbottle, G.

1994-12-31

Compositional characterization of limestone from sources known to medieval craftsmen and from the monuments they built can be used in conjunction with stylistic and iconographic criteria to infer geographic origin of sculptures that have lost their histories. Limestone from 47 quarrying locations in France and from numerous medieval monuments have been subjected to neutron activation analysis (NAA) to form the nucleus of the Brookhaven Limestone Database. Even though the method and techniques of NAA are well established, this paper briefly summarizes the parameters and experimental conditions useful for determining those concentration variables for which limestone from different sources exhibits significantmore » and reproducible differences.« less

7 CFR 330.300a - Administrative instructions exempting soil from parts of Canada from certain restrictions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 5 2014-01-01 2014-01-01 false Administrative instructions exempting soil from parts... FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300a Administrative instructions exempting soil from parts...

7 CFR 330.302 - Domestic movements of earth (including soil), stone, etc.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Domestic movements of earth (including soil), stone...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.302 Domestic movements of earth (including soil), stone, etc. The interstate movement from...

7 CFR 330.302 - Domestic movements of earth (including soil), stone, etc.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 5 2012-01-01 2012-01-01 false Domestic movements of earth (including soil), stone...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.302 Domestic movements of earth (including soil), stone, etc. The interstate movement from...

7 CFR 330.302 - Domestic movements of earth (including soil), stone, etc.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 5 2011-01-01 2011-01-01 false Domestic movements of earth (including soil), stone...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.302 Domestic movements of earth (including soil), stone, etc. The interstate movement from...

7 CFR 330.300a - Administrative instructions exempting soil from parts of Canada from certain restrictions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Administrative instructions exempting soil from parts... FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300a Administrative instructions exempting soil from parts...

7 CFR 330.300a - Administrative instructions exempting soil from parts of Canada from certain restrictions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 5 2013-01-01 2013-01-01 false Administrative instructions exempting soil from parts... FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300a Administrative instructions exempting soil from parts...

7 CFR 330.302 - Domestic movements of earth (including soil), stone, etc.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 5 2014-01-01 2014-01-01 false Domestic movements of earth (including soil), stone...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.302 Domestic movements of earth (including soil), stone, etc. The interstate movement from...

7 CFR 330.302 - Domestic movements of earth (including soil), stone, etc.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 5 2013-01-01 2013-01-01 false Domestic movements of earth (including soil), stone...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.302 Domestic movements of earth (including soil), stone, etc. The interstate movement from...

7 CFR 330.300a - Administrative instructions exempting soil from parts of Canada from certain restrictions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 5 2011-01-01 2011-01-01 false Administrative instructions exempting soil from parts... FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300a Administrative instructions exempting soil from parts...

7 CFR 330.300a - Administrative instructions exempting soil from parts of Canada from certain restrictions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 5 2012-01-01 2012-01-01 false Administrative instructions exempting soil from parts... FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300a Administrative instructions exempting soil from parts...

77 FR 10472 - San Bernardino National Forest, Mountaintop Ranger District, California, Mitsubishi South Quarry...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-22

... Cushenbury Cement Plant. Concurrent reclamation would be conducted throughout the life of the quarry and, at... the lead state agency under the California Environmental Quality Act (CEQA), address specific... grades of limestone to meet the feed requirement for the cement plant would not be adequate for the life...

40 CFR 372.23 - SIC and NAICS codes to which this Part applies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... facilities primarily engaged in reproducing text, drawings, plans, maps, or other copy, by blueprinting...)); 212324Kaolin and Ball Clay Mining Limited to facilities operating without a mine or quarry and that are...)); 212393Other Chemical and Fertilizer Mineral Mining Limited to facilities operating without a mine or quarry...

Photographic copy of photograph, ca. 1921 (original print located in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photographic copy of photograph, ca. 1921 (original print located in the National Archives & Records Administration, Still Picture Branch, Panama Canal Collection Series 185-G, #453, Washington, D.C.). Aerial view of Quarry Heights and Balboa from Sosa Hill - Quarry Heights Military Reservation, Ancon Hill, Balboa, Former Panama Canal Zone, CZ

27 CFR 555.103 - Transactions among licensees/permittees and transactions among licensees and holders of user...

Code of Federal Regulations, 2013 CFR

2013-04-01

... explosive materials, e.g., resale, mining, quarrying, agriculture, construction, sport rocketry, road... the explosive materials, e.g., resale, mining, quarrying, agriculture, construction, sport rocketry... Management and Budget under control number 1140-0079) [ATF No. 1, 68 FR 13787, Mar. 20, 2003, as amended by...

Analytic hierarchy process helps select site for limestone quarry expansion in Barbados.

PubMed

Dey, Prasanta Kumar; Ramcharan, Eugene K

2008-09-01

Site selection is a key activity for quarry expansion to support cement production, and is governed by factors such as resource availability, logistics, costs, and socio-economic-environmental factors. Adequate consideration of all the factors facilitates both industrial productivity and sustainable economic growth. This study illustrates the site selection process that was undertaken for the expansion of limestone quarry operations to support cement production in Barbados. First, alternate sites with adequate resources to support a 25-year development horizon were identified. Second, technical and socio-economic-environmental factors were then identified. Third, a database was developed for each site with respect to each factor. Fourth, a hierarchical model in analytic hierarchy process (AHP) framework was then developed. Fifth, the relative ranking of the alternate sites was then derived through pair wise comparison in all the levels and through subsequent synthesizing of the results across the hierarchy through computer software (Expert Choice). The study reveals that an integrated framework using the AHP can help select a site for the quarry expansion project in Barbados.

Application of preliminary risk analysis at marble finishing plants in Recife's metropolitan area.

PubMed

de Melo Neto, Rútilo P; Kohlman Rabbani, Emilia R

2012-01-01

The finishing of marble occurs in quarries all over Brazil, being the most significant dimension of the ornamental stone sector, with 7,000 businesses. Recife's Metropolitan Area (RMR) contains approximately 106 marble quarries, 25 of them unionized. The study focused on the application of Preliminary Risk Analysis, conducted at two unionized quarries: M1, a small business; and the second, M2, considered a micro enterprise. In this analysis both the administrative and the productive sectors were evaluated. The fieldwork was done in the month of December 2010. The study revealed that the two quarries carried moderate risks in the administrative sector, mainly due to ergonomic factors, and that in the productive sectors the risks were high, specifically because of excess noise, dust material, and precarious electrical installations. Using the results of the qualitative analysis as a base, the need for quantitative study presents itself in order to determine the most adequate modes of protection to be of assistance in the management of these risks, guaranteeing the safety and health of the worker and consequently the improvement in productivity in this sector.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Imes, J.L.; Kleeschulte, M.J.

Ground-water-level measurements to support remedial actions were made in 37 piezometers and 19 monitoring wells during a 19-month period to assess the potential for ground-water flow from an abandoned quarry to the nearby St. Charles County well field, which withdraws water from the base of the alluvial aquifer. From 1957 to 1966, low-level radioactive waste products from the Weldon Spring chemical plant were placed in the quarry a few hundred feet north of the Missouri River alluvial plain. Uranium-based contaminants subsequently were detected in alluvial ground water south of the quarry. During all but flood conditions, lateral ground-water flow inmore » the bedrock from the quarry, as interpreted from water-table maps, generally is southwest toward Little Femme Osage Creek or south into the alluvial aquifer. After entering the alluvial aquifer, the ground water flows southeast to east toward a ground-water depression presumably produced by pumping at the St. Charles County well field. The depression position varies depending on the Missouri River stage and probably the number and location of active wells in the St. Charles County well field.« less

Double shock front formation in cylindrical radiative blast waves produced by laser irradiation of krypton gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, I.; Quevedo, H. J.; Feldman, S.

2013-12-15

Radiative blast waves were created by irradiating a krypton cluster source from a supersonic jet with a high intensity femtosecond laser pulse. It was found that the radiation from the shock surface is absorbed in the optically thick upstream medium creating a radiative heat wave that travels supersonically ahead of the main shock. As the blast wave propagates into the heated medium, it slows and loses energy, and the radiative heat wave also slows down. When the radiative heat wave slows down to the transonic regime, a secondary shock in the ionization precursor is produced. This paper presents experimental datamore » characterizing both the initial and secondary shocks and numerical simulations to analyze the double-shock dynamics.« less

Groundwater monitoring of an open-pit limestone quarry: groundwater characteristics, evolution and their connections to rock slopes.

PubMed

Eang, Khy Eam; Igarashi, Toshifumi; Fujinaga, Ryota; Kondo, Megumi; Tabelin, Carlito Baltazar

2018-03-06

Groundwater flow and its geochemical evolution in mines are important not only in the study of contaminant migration but also in the effective planning of excavation. The effects of groundwater on the stability of rock slopes and other mine constructions especially in limestone quarries are crucial because calcite, the major mineral component of limestone, is moderately soluble in water. In this study, evolution of groundwater in a limestone quarry located in Chichibu city was monitored to understand the geochemical processes occurring within the rock strata of the quarry and changes in the chemistry of groundwater, which suggests zones of deformations that may affect the stability of rock slopes. There are three distinct geological formations in the quarry: limestone layer, interbedded layer of limestone and slaty greenstone, and slaty greenstone layer as basement rock. Although the hydrochemical facies of all groundwater samples were Ca-HCO 3 type water, changes in the geochemical properties of groundwater from the three geological formations were observed. In particular, significant changes in the chemical properties of several groundwater samples along the interbedded layer were observed, which could be attributed to the mixing of groundwater from the limestone and slaty greenstone layers. On the rainy day, the concentrations of Ca 2+ and HCO 3 - in the groundwater fluctuated notably, and the groundwater flowing along the interbedded layer was dominated by groundwater from the limestone layer. These suggest that groundwater along the interbedded layer may affect the stability of rock slopes.

Evolution of the alteration process in time of granitic materials from Valdemorillo quarries used in built heritage, Madrid, Spain

NASA Astrophysics Data System (ADS)

Alvarez de Buergo, M.; Fort, R.; Perez-Monserrat, E. M.

2012-04-01

Alteration of building materials used for heritage construction already starts in the quarries, where materials are subjected to both natural alteration and anthropic decay, this latter caused by the rock extracting, cutting and carving processes. Once the materials are placed in the building, they are exposed to other agents that accelerate their decay, especially if they are exposed to aggressive environments. Materials petrophysical properties tend to vary according to the alteration degree they have experienced, the longer they have been exposed to decay agents, the greater the properties change. Surface hardness of granitic rocks tend to diminish when they deteriorate, increasing its porosity, which usually is reflected on a decrease of the ultrasound propagation velocity measurements. Ultrasound velocity and surface hardness were measured in 200 monzogranite ashlars use to build the Assumption of Our Lady church (Valdemorillo, Madrid, Spain). Ultrasound velocity was measured using the indirect transmission mode, with 54 kHz frequency transductors, and surface hardness by means of the Schmidt hammer rebound tester. This monument was erected in different building stages. The starting point was a Mozarab or Visigoth defensive tower (8th century). Templars readapt it to a castle-convent (12th and 14th centuries), the tower being converted into a higher bell-tower. During the 14th-15th centuries the Cistercian Order made significant modifications of the complex, being the construction of the Chapter House one of the last enlargements during the 17th century. The quarries located in the surroundings of the monument were used for the first building stages. In the recent fronts of these quarries that have been used along the 20th century, ultrasound and hardness measurements were performed to obtain the values of these parameters in unaltered materials to compare them to those measured in ashlars from different constructive periods. A total of 50 recent front quarries were measured. Results show that quarry granites ultrasound velocity is much higher than those measured in the granite building. The older the monument ashlars, the lower the US velocity values: from data of 2 515±630 ms-1 in quarry materials we measured velocities of 1 880±720 ms-1 in 17th ashlars, 1 415 ±335 ms-1 in 12th-13th ashlars and 1 040±170 ms-1 for the oldest granites (8th century). At the same time, for sclerommetric index, values decrease from 30±10 in quarries to 22±4 in the 8th century ashlars, 24 ±4 (12th-13th centuries) and 26 ± 5 for the granites placed back in the 17th century.

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... subpart apply to the following affected sources at primary lead smelters: sinter machine, blast furnace... (Incorporations by reference), and § 63.15 (Availability of information confidentiality). The following sections...

Ultrahigh energy neutrino afterglows of nearby long duration gamma-ray bursts

NASA Astrophysics Data System (ADS)

Thomas, Jessymol K.; Moharana, Reetanjali; Razzaque, Soebur

2017-11-01

Detection of ultrahigh energy (UHE, ≳1 PeV ) neutrinos from astrophysical sources will be a major advancement in identifying and understanding the sources of UHE cosmic rays (CRs) in nature. Long duration gamma-ray burst (GRB) blast waves have been considered as potential acceleration sites of UHECRs. These CRs are expected to interact with GRB afterglow photons, which are synchrotron radiation from relativistic electrons coaccelerated with CRs in the blast wave, and naturally produce UHE neutrinos. Fluxes of these neutrinos are uncertain, however, and crucially depend on the observed afterglow modeling. We have selected a sample of 23 long duration GRBs within redshift 0.5 for which adequate electromagnetic afterglow data are available and which could produce high flux of UHE afterglow neutrinos, being nearby. We fit optical, x-ray, and γ -ray afterglow data with an adiabatic blast wave model in a constant density interstellar medium and in a wind environment where the density of the wind decreases as the inverse square of the radius from the center of the GRB. The blast wave model parameters extracted from these fits are then used for calculating UHECR acceleration and p γ interactions to produce UHE neutrino fluxes from these GRBs. We have also explored the detectability of these neutrinos by currently running and upcoming large area neutrino detectors, such as the Pierre Auger Observatory, IceCube Gen-2, and KM3NeT observatories. We find that our realistic flux models from nearby GRBs will be unconstrained in the foreseeable future.

The efficacy of radiant heat controls on workers' heat stress around the blast furnace of a steel industry.

PubMed

Giahi, Omid; Darvishi, Ebrahim; Aliabadi, Mohsen; Khoubi, Jamshid

2015-01-01

Workers' exposure to excessive heat in molten industries is mainly due to radiant heat from hot sources. The aim of this study was to evaluate the efficacy of radiant heat controls on workers heat stress around a typical blast furnace. Two main interventions were applied for reducing radiant heat around the blast furnace of a steel industry located in western Iran. These included using a heat absorbing system in the furnace body and installing reflective aluminum barrier in the main workstation. Heat stress indexes were measured before and after each intervention using the digital WBGT-meter. The results showed MRT and WBGT indexes decreased by 20 °C and 3.9 °C, respectively after using heat absorbing system and also decreased by 18.6 °C and 2.5 °C, respectively after installing a reflective barrier. These indexes decrease by 26.5 °C and 5.2 °C, respectively due to the simultaneous application of the two interventions which were statistically significant (p < 0.001). The core body temperature of workers decreased by 2.6 °C after the application of interventions which was also significant (p < 0.05). The results confirmed heat control at source can be considered as a first solution for reducing radiant heat of blast furnaces. However, the simultaneous application of interventions could noticeably reduce worker heat stress. The results provide reliable information in order to implement the effective heat controls in typical hot steel industries.

"Sydney sandstone": Heritage Stone from Australia

NASA Astrophysics Data System (ADS)

Cooper, Barry; Kramar, Sabina

2014-05-01

Sydney is Australia's oldest city being founded in 1788. The city was fortunate to be established on an extensive and a relatively undeformed layer of lithified quartz sandstone of Triassic age that has proved to be an ideal building stone. The stone has been long identified by geologists as the Hawkesbury Sandstone. On the other hand the term "Sydney sandstone" has also been widely used over a long period, even to the extent of being utilised as the title of published books, so its formal designation as a heritage stone will immediately formalise this term. The oldest international usage is believed to be its use in the construction of the Stone Store at Kerikeri, New Zealand (1832-1836). In the late 19th century, public buildings such as hospitals, court houses as well as the prominent Sydney Town Hall, Sydney General Post Office, Art Gallery of New South Wales, State Library of New South Wales as well as numerous schools, churches, office building buildings, University, hotels, houses, retaining walls were all constructed using Sydney sandstone. Innumerable sculptures utilising the gold-coloured stone also embellished the city ranging from decorative friezes and capitals on building to significant monuments. Also in the late 19th and early 20th century, Sydney sandstone was used for major construction in most other major Australian cities especially Melbourne, Adelaide and Brisbane to the extent that complaints were expressed that suitable local stone materials were being neglected. Quarrying of Sydney sandstone continues today. In 2000 it was recorded noted that there were 33 significant operating Sydney sandstone quarries including aggregate and dimension stone operations. In addition sandstone continues to be sourced today from construction sites across the city area. Today major dimension stone producers (eg Gosford Quarries) sell Sydney sandstone not only into the Sydney market but also on national and international markets as cladding and paving products as well as block. Recent international projects by Gosford Quarries include Mishima Golf Club in Japan, Al Awadi Tower in Kuwait, New World Resort in China and a Hard Rock Café in Florida, USA. Arguably Sydney sandstone is Australia's most prominent potential Global Heritage Stone Resource and details are readily available in existing publications to make the nomination.

A Revised Earthquake Catalogue for South Iceland

NASA Astrophysics Data System (ADS)

Panzera, Francesco; Zechar, J. Douglas; Vogfjörd, Kristín S.; Eberhard, David A. J.

2016-01-01

In 1991, a new seismic monitoring network named SIL was started in Iceland with a digital seismic system and automatic operation. The system is equipped with software that reports the automatic location and magnitude of earthquakes, usually within 1-2 min of their occurrence. Normally, automatic locations are manually checked and re-estimated with corrected phase picks, but locations are subject to random errors and systematic biases. In this article, we consider the quality of the catalogue and produce a revised catalogue for South Iceland, the area with the highest seismic risk in Iceland. We explore the effects of filtering events using some common recommendations based on network geometry and station spacing and, as an alternative, filtering based on a multivariate analysis that identifies outliers in the hypocentre error distribution. We identify and remove quarry blasts, and we re-estimate the magnitude of many events. This revised catalogue which we consider to be filtered, cleaned, and corrected should be valuable for building future seismicity models and for assessing seismic hazard and risk. We present a comparative seismicity analysis using the original and revised catalogues: we report characteristics of South Iceland seismicity in terms of b value and magnitude of completeness. Our work demonstrates the importance of carefully checking an earthquake catalogue before proceeding with seismicity analysis.

Sedimentology of the Early Jurassic terrestrial Steierdorf Formation in Anina, Colonia Cehă Quarry, South Carpathians, Romania

NASA Astrophysics Data System (ADS)

Kędzior, Artur; Popa, Mihai E.

2013-06-01

Kędzior, A. and Popa, E.M. 2013. Sedimentology of the Early Jurassic terrestrial Steierdorf Formation in Anina, Colonia Cehă Quarry, South Carpathians, Romania. Acta Geologica Polonica, 63 (2), 175-199. Warszawa. The continental, coal bearing Steierdorf Formation, Hettangian - Sinemurian in age, is included in the Mesozoic cover of the Reşiţa Basin, Getic Nappe, South Carpathians, Romania. The Steierdorf Formation can be studied in Anina, a coal mining center and an exceptional locality for Early Jurassic flora and fauna, occurring in the middle of the Reşiţa Basin. This paper presents the results of sedimentological, stratigraphical and paleobotanical researches undertaken in Colonia Cehă open cast mine in Anina, where the Steierdorf Formation outcrops widely. Several sedimentary facies associations have been described, these associations permitting the reconstruction of various depositional systems such as alluvial fans, braided and meandering river systems, as well as lacustrine and coal generating marsh systems of the Steierdorf Formation. The sedimentary associations recorded within the Steierdorf Formation show a gradual fining upward trend, pointing to a rising marine water table and a decreasing relief within the source area.

The Effects of Fracture Anisotropy on the Damage Pattern and Seismic Radiation from a Chemical Explosion in a Granite Quarry

NASA Astrophysics Data System (ADS)

Rogers-Martinez, M. A.; Sammis, C. G.; Ezzedine, S. M.

2017-12-01

As part of the New England Damage Experiment (NEDE) a 122.7 kg Heavy ANFO charge was detonated at a depth of 13 m in a granite quarry in Barre Vt. Subsequent drill cores from the source region revealed that most of the resultant fracturing was concentrated in the rift plane of the highly anisotropic Barre granite. We simulated this explosion using a dynamic damage mechanics model embedded in the ABAQUS 3D finite element code. The damage mechanics was made anisotropic by taking the critical stress intensity factor to be a function of azimuth in concert with the physics of interacting parallel fractures and laboratory studies of anisotropic granite. In order to identify the effects of anisotropy, the explosion was also simulated assuming 1) no initial damage (pure elasticity) and 2) isotropic initial damage. For the anisotropic case, the calculated fracture pattern simulated that observed in NEDE. The simulated seismic radiation looked very much like that from a tensile fracture oriented in the rift plane, and similar to the crack-like moment tensor observed in the far field of many nuclear explosions.

7 CFR 330.300 - Soil from foreign countries or Territories or possessions. 1

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 5 2012-01-01 2012-01-01 false Soil from foreign countries or Territories or...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300 Soil from foreign countries or Territories or possessions. 1 1 The movement of soil from...

7 CFR 330.300 - Soil from foreign countries or Territories or possessions. 1

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 5 2014-01-01 2014-01-01 false Soil from foreign countries or Territories or...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300 Soil from foreign countries or Territories or possessions. 1 1 The movement of soil from...

7 CFR 330.300 - Soil from foreign countries or Territories or possessions. 1

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 5 2011-01-01 2011-01-01 false Soil from foreign countries or Territories or...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300 Soil from foreign countries or Territories or possessions. 1 1 The movement of soil from...

7 CFR 330.300 - Soil from foreign countries or Territories or possessions. 1

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Soil from foreign countries or Territories or...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300 Soil from foreign countries or Territories or possessions. 1 1 The movement of soil from...

7 CFR 330.300 - Soil from foreign countries or Territories or possessions. 1

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 5 2013-01-01 2013-01-01 false Soil from foreign countries or Territories or...; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products § 330.300 Soil from foreign countries or Territories or possessions. 1 1 The movement of soil from...

Deep Impact Spots Quarry

NASA Technical Reports Server (NTRS)

2005-01-01

Sixty-nine days before it gets up-close-and-personal with a comet, NASA's Deep Impact spacecraft successfully photographed its quarry, comet Tempel 1, at a distance of 39.7 million miles. The image, taken on April 25, 2005, is the first of many comet portraits Deep Impact will take leading up to its historic comet encounter on July 4.

Reducing the risk of the collapse of the soil by macro system modeling the slopes stability of the quarries

NASA Astrophysics Data System (ADS)

Klimova, E. V.; Semeykin, A. Yu

2018-01-01

The urgent task of modern production is to reduce the risks of man-made disasters and, as a consequence, preserve the life and health of workers, material properties and natural environment. In the mining industry, one of the reasons for the high level of injuries and accidents is the collapse of the soil. Macro system modelling of slopes stability of the quarries is based on the compliance with the conditions of physical and mathematical correctness of the application of the model of a continuous medium. This type of modelling allows to choose the safe parameters of the slopes of the quarries and to reduce the risk of collapse of the soil.

Earthquake recording at the Stanford DAS Array with fibers in existing telecomm conduits

NASA Astrophysics Data System (ADS)

Biondi, B. C.; Martin, E. R.; Yuan, S.; Cole, S.; Karrenbach, M. H.

2017-12-01

The Stanford Distributed Acoustic Sensing Array (SDASA-1) has been continuously recording seismic data since September 2016 on 2.5 km of single mode fiber optics in existing telecommunications conduits under Stanford's campus. The array is figure-eight shaped and roughly 600 m along its widest side with a channel spacing of roughly 8 m. This array is easy to maintain and is nonintrusive, making it well suited to urban environments, but it sacrifices some cable-to-ground coupling compared to more traditional seismometers. We have been testing its utility for earthquake recording, active seismic, and ambient noise interferometry. This talk will focus on earthquake observations. We will show comparisons between the strain rates measured throughout the DAS array and the particle velocities measured at the nearby Jasper Ridge Seismic Station (JRSC). In some of these events, we will point out directionality features specific to DAS that can require slight modifications in data processing. We also compare repeatability of DAS and JRSC recordings of blasts from a nearby quarry. Using existing earthquake databases, we have created a small catalog of DAS earthquake observations by pulling records of over 700 Northern California events spanning Sep. 2016 to Jul. 2017 from both the DAS data and JRSC. On these events we have tested common array methods for earthquake detection and location including beamforming and STA/LTA analysis in time and frequency. We have analyzed these events to approximate thresholds on what distances and magnitudes are clearly detectible by the DAS array. Further analysis should be done on detectability with methods tailored to small events (for example, template matching). In creating this catalog, we have developed open source software available for free download that can manage large sets of continuous seismic data files (both existing files, and files as they stream in). This software can both interface with existing earthquake networks, and efficiently extract earthquake recordings from many continuous recordings saved on the users machines.

Crustal parameters in the Iberian Peninsula

NASA Astrophysics Data System (ADS)

Banda, E.

1988-06-01

The structure of the crust in the Iberian Peninsula has been investigated for the last 15 years by Spanish and Portuguese groups in close collaboration with other European institutions. The first experiments were carried out in Portugal (Mueller et al., 1973) with the aim of investigating the crustal structure of the Hercynian belt in the southwest corner of the Iberian peninsula. Other experiments have been subsequently realized to study different aspects of the crust in various regions of Portugal. In Spain the main effort has been focused in Alpine areas, with the first experiments in the Alboran Sea and the Betic Cordilleras (Working Group for Deep Seismic Sounding in Spain, 1974-1975, 1977; Working Group for Deep Seismic Sounding in the Alboran Sea, 1974-1975, 1978). Follow-up experiments until 1981 completed the work in the Betic Cordillera. Extensive experiments were carried out in the Pyrenees in 1978. Further surveys covered the Balearic Islands in 1976, the Valencia Trough in 1976 and 1983, and the Celtiberian Chain (or Iberic system) in 1981. The Hercynian belt has only been studied in detail in the northwest corner of Spain in 1982, with smaller studies in the central Iberian Massif in 1976 and 1986. Mostaanpour (1984) has compiled some crustal parameters (crustal thickness, average crustal velocity and Pn velocity) for western Europe. Meanwhile, more complete data are available for the Iberian Peninsula. The results presented here were derived from a large number of seismic refraction experiments which have been carried out mostly along or close to coastal areas of the Iberian Peninsula. Offshore explosions of various sizes were used as the energy source in most cases, in addition to some quarry blasts. Unfortunately this leaves most of the inner part of the Iberian Peninsula unsurveyed. Our purpose is to summarize some of the crustal parameters obtained so far and to detail the appropriate literature for the interested reader.

Detecting Slow Deformation Signals Preceding Dynamic Failure: A New Strategy For The Mitigation Of Natural Hazards (SAFER)

NASA Astrophysics Data System (ADS)

Vinciguerra, S.; Colombero, C.; Comina, C.; Umili, G.

2015-12-01

Rock slope monitoring is a major aim in territorial risk assessment and mitigation. The use of "site specific" microseismic monitoring systems can allow to detect pre-failure signals in unstable sectors within the rock mass and to predict the possible acceleration to the failure. To this aim multi-scale geophysical methods can provide a unique tool for an high-resolution imaging of the internal structure of the rock mass and constraints on the physical state of the medium. We present here a cross-hole seismic tomography survey coupled with laboratory ultrasonic velocity measurements and determination of physical properties on rock samples to characterize the damaged and potentially unstable granitic cliff of Madonna del Sasso (NW, Italy). Results allowed to achieve two main advances, in terms of obtaining: i) a lithological interpretation of the velocity field obtained at the site, ii) a systematic correlation of the measured velocities with physical properties (density and porosity) and macroscopic features of the granite (weathering and anisotropy) of the cliff. A microseismic monitoring system developed by the University of Turin/Compagnia San Paolo, consisting of a network of 4 triaxial geophones (4.5 Hz) connected to a 12-channel data logger, has been deployed on the unstable granitic cliff. More than 2000 events with different waveforms, duration and frequency content were recorded between November 2013 and July 2014. By inspecting the acquired events we identified the key parameters for a reliable distinction among the nature of each signal, i.e. the signal shape (in terms of amplitude, duration, kurtosis) and the frequency content (maximum frequency content and frequency distribution). Four main classes of recorded signals can be recognised: microseismic events, regional earthquakes, electrical noises and calibration signals, and unclassified events (probably grouping rockfalls, quarry blasts, other anthropic and natural sources of seismic noise).

The Sedov Blast Wave as a Radial Piston Verification Test

DOE PAGES

Pederson, Clark; Brown, Bart; Morgan, Nathaniel

2016-06-22

The Sedov blast wave is of great utility as a verification problem for hydrodynamic methods. The typical implementation uses an energized cell of finite dimensions to represent the energy point source. We avoid this approximation by directly finding the effects of the energy source as a boundary condition (BC). Furthermore, the proposed method transforms the Sedov problem into an outward moving radial piston problem with a time-varying velocity. A portion of the mesh adjacent to the origin is removed and the boundaries of this hole are forced with the velocities from the Sedov solution. This verification test is implemented onmore » two types of meshes, and convergence is shown. Our results from the typical initial condition (IC) method and the new BC method are compared.« less

Jurassic Diabase from Leesburg, VA: A Proposed Lunar Simulant

NASA Technical Reports Server (NTRS)

Taylor, Patrick T.; Lowman, P. D.; Nagihara, Seiichi; Milam, M. B.; Nakamura, Yosio

2008-01-01

A study of future lunar seismology and heat flow is being carried out as part of the NASA Lunar Sortie Science Program. This study will include new lunar drilling techniques, using a regolith simulant, for emplacement of instruments. Previous lunar simulants, such as JSC-1 and MLS-1, were not available when the study began, so a local simulant source was required. Diabase from a quarry at Leeseburg, Virginia, was obtained from the Luck Stone Corporation. We report here initial results of a petrographic examination of this rock, GSC-1 henceforth.

Jurassic Diabase from Leesburg, VA: A Proposed Lunar Simulant

NASA Technical Reports Server (NTRS)

Taylor, P. T.; Lowman, P. D.; Nagihara, Seiichi; Milam, M. B.; Nakamura, Yosio

2008-01-01

A study of future lunar seismology and heat flow is being carried out as part of the NASA Lunar Sortie Science Program [1].This study will include new lunar drilling techniques, using a regolith simulant, for emplacement of instruments. Previous lunar simulants, such as JSC-I and MLS-l, were not available when the study began, so a local simulant source was required. Diabase from a quarry at Leesburg, Virginia, was obtained from the Luck Stone Corporation. We report here initial results of a petrographic examination of this rock, GSC-1 henceforth.

Integrated Verification Experiment data collected as part of the Los Alamos National Laboratory's Source Region Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fitzgerald, T.J.; Carlos, R.C.; Argo, P.E.

As part of the integrated verification experiment (IVE), we deployed a network of hf ionospheric sounders to detect the effects of acoustic waves generated by surface ground motion following underground nuclear tests at the Nevada Test Site. The network sampled up to four geographic locations in the ionosphere from almost directly overhead of the surface ground zero out to a horizontal range of 60 km. We present sample results for four of the IVEs: Misty Echo, Texarkana, Mineral Quarry, and Bexar.

Textbook of Military Medicine. Part 1. Warfare, Weaponry, and the Casualty. Part 5. Conventional Warfare. Ballistic, Blast, and Burn Injuries

DTIC Science & Technology

1991-01-01

United States. Because the vast majority of our patients are not active -duty military personnel, it may seem that our day-to-day ac- tivities are far... activated . A designated time-delay fuse uses an Source: Reference 8 15 Conventional Warfare: Ballistic, Blast, and Burn Injuries explosion and the...be found embedded and unexploded in tissue. The fuse is located at the tip of the warhead, and is activated and will deionate on contact only after

Kablammo: an interactive, web-based BLAST results visualizer.

PubMed

Wintersinger, Jeff A; Wasmuth, James D

2015-04-15

Kablammo is a web-based application that produces interactive, vector-based visualizations of sequence alignments generated by BLAST. These visualizations can illustrate many features, including shared protein domains, chromosome structural modifications and genome misassembly. Kablammo can be used at http://kablammo.wasmuthlab.org. For a local installation, the source code and instructions are available under the MIT license at http://github.com/jwintersinger/kablammo. jeff@wintersinger.org. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Characterization of Pseudomonas syringae pv. syringae, Causal Agent of Citrus Blast of Mandarin in Montenegro.

PubMed

Ivanović, Žarko; Perović, Tatjana; Popović, Tatjana; Blagojević, Jovana; Trkulja, Nenad; Hrnčić, Snježana

2017-02-01

Citrus blast caused by bacterium Pseudomonas syringae is a very important disease of citrus occuring in many areas of the world, but with few data about genetic structure of the pathogen involved. Considering the above fact, this study reports genetic characterization of 43 P. syringae isolates obtained from plant tissue displaying citrus blast symptoms on mandarin ( Citrus reticulata ) in Montenegro, using multilocus sequence analysis of gyrB , rpoD , and gap1 gene sequences. Gene sequences from a collection of 54 reference pathotype strains of P. syringae from the Plant Associated and Environmental Microbes Database (PAMDB) was used to establish a genetic relationship with our isolates obtained from mandarin. Phylogenetic analyses of gyrB , rpoD , and gap1 gene sequences showed that P. syringae pv. syringae causes citrus blast in mandarin in Montenegro, and belongs to genomospecies 1. Genetic homogeneity of isolates suggested that the Montenegrian population might be clonal which indicates a possible common source of infection. These findings may assist in further epidemiological studies of this pathogen and for determining mandarin breeding strategies for P. syringae control.

Characterization of Pseudomonas syringae pv. syringae, Causal Agent of Citrus Blast of Mandarin in Montenegro

PubMed Central

Ivanović, Žarko; Perović, Tatjana; Popović, Tatjana; Blagojević, Jovana; Trkulja, Nenad; Hrnčić, Snježana

2017-01-01

Citrus blast caused by bacterium Pseudomonas syringae is a very important disease of citrus occuring in many areas of the world, but with few data about genetic structure of the pathogen involved. Considering the above fact, this study reports genetic characterization of 43 P. syringae isolates obtained from plant tissue displaying citrus blast symptoms on mandarin (Citrus reticulata) in Montenegro, using multilocus sequence analysis of gyrB, rpoD, and gap1 gene sequences. Gene sequences from a collection of 54 reference pathotype strains of P. syringae from the Plant Associated and Environmental Microbes Database (PAMDB) was used to establish a genetic relationship with our isolates obtained from mandarin. Phylogenetic analyses of gyrB, rpoD, and gap1 gene sequences showed that P. syringae pv. syringae causes citrus blast in mandarin in Montenegro, and belongs to genomospecies 1. Genetic homogeneity of isolates suggested that the Montenegrian population might be clonal which indicates a possible common source of infection. These findings may assist in further epidemiological studies of this pathogen and for determining mandarin breeding strategies for P. syringae control. PMID:28167885

Maximum volume cuboids for arbitrarily shaped in-situ rock blocks as determined by discontinuity analysis—A genetic algorithm approach

NASA Astrophysics Data System (ADS)

Ülker, Erkan; Turanboy, Alparslan

2009-07-01

The block stone industry is one of the main commercial use of rock. The economic potential of any block quarry depends on the recovery rate, which is defined as the total volume of useful rough blocks extractable from a fixed rock volume in relation to the total volume of moved material. The natural fracture system, the rock type(s) and the extraction method used directly influence the recovery rate. The major aims of this study are to establish a theoretical framework for optimising the extraction process in marble quarries for a given fracture system, and for predicting the recovery rate of the excavated blocks. We have developed a new approach by taking into consideration only the fracture structure for maximum block recovery in block quarries. The complete model uses a linear approach based on basic geometric features of discontinuities for 3D models, a tree structure (TS) for individual investigation and finally a genetic algorithm (GA) for the obtained cuboid volume(s). We tested our new model in a selected marble quarry in the town of İscehisar (AFYONKARAHİSAR—TURKEY).

Structural analysis of sheath folds in the Sylacauga Marble Group, Talladega slate belt, southern Appalachians

USGS Publications Warehouse

Mies, J.W.

1993-01-01

Remnant blocks of marble from the Moretti-Harrah dimension-stone quarry provide excellent exposure of meter-scale sheath folds. Tubular structures with elliptical cross-sections (4 ???Ryz ??? 5) are the most common expression of the folds. The tubes are elongate subparallel to stretching lineation and are defined by centimeter-scale layers of schist. Eccentrically nested elliptical patterns and opposing asymmetry of folds ('S' and 'Z') are consistent with the sheath-fold interpretation. Sheath folds are locally numerous in the Moretti-Harrah quarry but are not widely distributed in the Sylacauga Marble Group; reconnaissance in neighboring quarries provided no additional observations. The presence of sheath folds in part of the Talladega slate belt indicates a local history of plastic, non-coaxial deformation. Such a history of deformation is substantiated by petrographic study of an extracted hinge from the Moretti-Harrah quarry. The sheath folds are modeled as due to passive amplification of initial structures during simple shear, using both analytic geometry and graphic simulation. As indicated by these models, relatively large shear strains (y ??? 9) and longitudinal initial structures are required. The shear strain presumably relates to NW-directed displacement of overlying crystalline rocks during late Paleozoic orogeny. ?? 1993.

Directed blasts and blast-generated pyroclastic density currents: a comparison of the Bezymianny 1956, Mount St Helens 1980, and Soufrière Hills, Montserrat 1997 eruptions and deposits

USGS Publications Warehouse

Belousov, Alexander; Voight, Barry; Belousova, Marina

2007-01-01

We compare eruptive dynamics, effects and deposits of the Bezymianny 1956 (BZ), Mount St Helens 1980 (MSH), and Soufrière Hills volcano, Montserrat 1997 (SHV) eruptions, the key events of which included powerful directed blasts. Each blast subsequently generated a high-energy stratified pyroclastic density current (PDC) with a high speed at onset. The blasts were triggered by rapid unloading of an extruding or intruding shallow magma body (lava dome and/or cryptodome) of andesitic or dacitic composition. The unloading was caused by sector failures of the volcanic edifices, with respective volumes for BZ, MSH, and SHV c. 0.5, 2.5, and 0.05 km3 . The blasts devastated approximately elliptical areas, axial directions of which coincided with the directions of sector failures. We separate the transient directed blast phenomenon into three main parts, the burst phase, the collapse phase, and the PDC phase. In the burst phase the pressurized mixture is driven by initial kinetic energy and expands rapidly into the atmosphere, with much of the expansion having an initially lateral component. The erupted material fails to mix with sufficient air to form a buoyant column, but in the collapse phase, falls beyond the source as an inclined fountain, and thereafter generates a PDC moving parallel to the ground surface. It is possible for the burst phase to comprise an overpressured jet, which requires injection of momentum from an orifice; however some exploding sources may have different geometry and a jet is not necessarily formed. A major unresolved question is whether the preponderance of strong damage observed in the volcanic blasts should be attributed to shock waves within an overpressured jet, or alternatively to dynamic pressures and shocks within the energetic collapse and PDC phases. Internal shock structures related to unsteady flow and compressibility effects can occur in each phase. We withhold judgment about published shock models as a primary explanation for the damage sustained at MSH until modern 3D numerical modeling is accomplished, but argue that much of the damage observed in directed blasts can be reasonably interpreted to have been caused by high dynamic pressures and clast impact loading by an inclined collapsing fountain and stratified PDC. This view is reinforced by recent modeling cited for SHV. In distal and peripheral regions, solids concentration, maximum particle size, current speed, and dynamic pressure are diminished, resulting in lesser damage and enhanced influence by local topography on the PDC. Despite the different scales of the blasts (devastated areas were respectively 500, 600, and >10 km2 for BZ, MSH, and SHV), and some complexity involving retrogressive slide blocks and clusters of explosions, their pyroclastic deposits demonstrate strong similarity. Juvenile material composes >50% of the deposits, implying for the blasts a dominantly magmatic mechanism although hydrothermal explosions also occurred. The character of the magma fragmented by explosions (highly viscous, phenocryst-rich, variable microlite content) determined the bimodal distributions of juvenile clast density and vesicularity. Thickness of the deposits fluctuates in proximal areas but in general decreases with distance from the crater, and laterally from the axial region. The proximal stratigraphy of the blast deposits comprises four layers named A, B, C, D from bottom to top. Layer A is represented by very poorly sorted debris with admixtures of vegetation and soil, with a strongly erosive ground contact; its appearance varies at different sites due to different ground conditions at the time of the blasts. The layer reflects intense turbulent boundary shear between the basal part of the energetic head of the PDC and the substrate. Layer B exhibits relatively well-sorted fines depleted debris with some charred plant fragments; its deposition occurred by rapid suspension sedimentation in rapidly waning, high-concentration conditions. Layer C is mainly a poorly sorted massive layer enriched by fines with its uppermost part laminated, created by rapid sedimentation under moderate-concentration, weakly tractive conditions, with the uppermost laminated part reflecting a dilute depositional regime with grain-by-grain traction deposition. By analogy to laboratory experiments, mixing at the flow head of the PDC created a turbulent dilute wake above the body of a gravity current, with layer B deposited by the flow body and layer C by the wake. The uppermost layer D of fines and accretionary lapilli is an ash fallout deposit of the finest particles from the high-rising buoyant thermal plume derived from the sediment-depleted pyroclastic density current. The strong similarity among these eruptions and their deposits suggests that these cases represent similar source, transport and depositional phenomena.

The relevance of "Santa Pudia" calcarenite: a natural stone to preserve heritage buildings in Andalusia (Spain)

NASA Astrophysics Data System (ADS)

Navarro, Rafael; Molina, Eduardo; Baltuille, José Manuel

2013-04-01

"Santa Pudia" calcarenite, extracted in quarries from Granada (Andalusia, Spain), is a very important ornamental stone used in some of the main historical buildings in Andalusia, and particularly in the city of Granada. It has been used mainly outdoors with structural purposes (ashlars, columns), but is also used as decorative element in façades, pinnacles, etc. There are two main quarries, one historical ("Las Parideras") and another one currently under exploitation ("La Escribana"). Both were the source for all the material to make the different cited elements. Some of the main historical buildings using this stone in their construction, in one way or other, are the cathedral, The Royal Chapel, the Royal Hospital, San Juan de Dios monastery, the Royal Chancery or Carlos V Palace in the Alhambra, all of them in the city of Granada. In recent days, this natural stone has been used in the restoration of the Mosque of Córdoba and the Cinco Llagas Hospital in Seville. Although the main reference in industry for this natural stone is "Calcarenita de Santa Pudia", it can be found as well cited in the old literature under the denomination of "Piedra Franca". From a geological point of view is a white to yellow calcarenite, part of the Tortonian deposits of the Guadalquivir Basin (Post-Orogenic Neogene Basins of the Betic Chains). It's made up mainly by micritic matrix of calcite, with fragments of bioclasts (about 90%) including molluscs, echinoderms, briozoan, red algae and foraminifera. Other components, like metamorphic quartz, moscovite and/or schist or gneiss (rock fragments from the nearby metamorphic basement), can be found as well. The rock is poorly cemented with sparitic calcite. Regarding the main physical and mechanical properties, this rock has an open porosity between 25-36%, bulk density of 1,74 g/cm3, water absorption values at atmospheric pressure of 16%, compressive strength (dry) of 11 MPa, flexural strength (dry) of 2,3 MPa and salt crystallization loss of mass of 5%. It is a natural stone that easily decays in urban environments, therefore the importance of its proper knowledge and characterization. This natural stone, because of its relevance in the main heritage buildings in the monumental city of Granada can be considered a very important natural stone in Andalusia. Its nomination as Global Heritage Stone Resource will help to preserve the material, both in quarries and in historical buildings. This will guarantee the conservation and availability of material for future restoration works when needed. Its nomination is important as well to avoid the mistakes that can be produced from the equal name that is given to other natural stones quarried these days, not only in Andalusia (e.g. Piedra Dorada or Piedra Franca from Porcuna, in Jaén), but in other parts of Spain as well (e.g. Villamayor sandstone or Piedra Franca, quarried in Salamanca). This is a contribution of the Spanish network CONSTRUROCK.

40 CFR 60.120 - Applicability and designation of affected facility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of...: Pot furnaces of more than 250 kg (550 lb) charging capacity, blast (cupola) furnaces, and...

40 CFR 60.120 - Applicability and designation of affected facility.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of...: Pot furnaces of more than 250 kg (550 lb) charging capacity, blast (cupola) furnaces, and...

Asbestos exposure during quarrying and processing of serpentinites: a case study in Valmalenco, Central Alps, Northern Italy

NASA Astrophysics Data System (ADS)

Cavallo, A.; Rimoldi, B.

2012-04-01

Serpentinites are metamorphic rocks derived from ultramafics such as peridotites (lherzolites and/or harzburgites), with a typical mineralogical assemblage of antigorite, olivine, diopside and minor magnetite, chlorite and chrysotile. If the rock mass has good geotechnical properties, these stones are quarried because of their wide variety of green shades and outstanding technical properties. Excellent stones are produced in the Malenco Valley, Central Alps (northern Italy, Sondrio): here the geological set-up is dominated by the ultramafic Malenco massif (lower crust-mantle complex), exposed at the Penninic to Austroalpine boundary zone. Different processing operations give origin to valuable products like stoves, funeral monuments, design home appliances; important building element as roof slabs, tiles for floor and wall coverings constitute the main commercial line of production. In this area, good quality long fibre chrysotile asbestos was mined since the XIX century, till the seventies. The asbestos fissures (mostly slip-fiber) are well known in Valmalenco, associated to an important ENE-WSW striking fracture and hydrothermal vein system. Some actual serpentinite quarries "cross" at times tunnels of the old asbestos mines, because the fracture and vein system "guides" the extraction. At present time, this area represents an excellent example of naturally occurring asbestos (NOA). For these reasons, workers' exposure to asbestos during quarrying and processing cannot be ruled out, and must be assessed according to national laws. From 2004 to nowadays, the INAIL Regional Management of Lombardia, with the collaboration of University of Milan-Bicocca, carried out extensive monitoring campaigns both in quarries and in processing laboratories. More than 300 massive samples (rocks and veins) and 250 airborne dust samples were collected during the surveys. One of the main problems in the study of massive serpentinites is the accurate identification of the different serpentine minerals due to the close resemblance of their basic structures. For this reason, the massive samples were studied by combined use of optical microscopy, SEM-EDS, X-ray powder diffraction and FT-IR. Geological and geostructural mapping of the chrysotile veins was also performed by the University, in order to characterize and quantify the "asbestos content" in each quarry. The analyses performed on massive samples showed that chrysotile asbestos is concentrated only along fissures and veins, and is not "dispersed" in the rock. Airborne personal and environmental samples (performed both in quarries and laboratories), were analyzed by means of phase-contrast microscopy (PCM) and SEM-EDS. The exposure values were extremely variable, and mostly below the permissible exposure level. The airborne samples revealed some critical details: the extreme fineness of chrysotile fibers (not detectable by PCM), the presence of chrysotile "aggregates", the difficulty to distinguish between chrysotile and splintery antigorite fragments (produced by mechanical fragmentation during quarrying and processing). Prevention actions were planned on the basis of the analytical results, and are still in progress: preliminary geological surveys (in order to avoid mineralized fissures), drilling technologies, dust suction and water abatement were tested in the field, procedural and organizational solutions are implemented both in the quarries and in the processing sites. Employers and workers are trained appropriately according to the law. A specific method for monitoring NOA exposure in these workplaces will be soon released.

Fake ballistics and real explosions: field-scale experiments on the ejection and emplacement of volcanic bombs during vent-clearing explosive activity

NASA Astrophysics Data System (ADS)

Taddeucci, J.; Valentine, G.; Gaudin, D.; Graettinger, A. H.; Lube, G.; Kueppers, U.; Sonder, I.; White, J. D.; Ross, P.; Bowman, D. C.

2013-12-01

Ballistics - bomb-sized pyroclasts that travel from volcanic source to final emplacement position along ballistic trajectories - represent a prime source of volcanic hazard, but their emplacement range, size, and density is useful to inverse model key eruption parameters related to their initial ejection velocity. Models and theory, however, have so far focused on the trajectory of ballistics after leaving the vent, neglecting the complex dynamics of their initial acceleration phase in the vent/conduit. Here, we use field-scale buried explosion experiments to study the ground-to-ground ballistic emplacement of particles through their entire acceleration-deceleration cycle. Twelve blasts were performed at the University at Buffalo Large Scale Experimental Facility with a range of scaled depths (burial depth divided by the cubic root of the energy of the explosive charge) and crater configurations. In all runs, ballistic analogs were placed on the ground surface at variable distance from the vertical projection of the buried charge, resulting in variable ejection angle. The chosen analogs are tennis and ping-pong balls filled with different materials, covering a limited range of sizes and densities. The analogs are tracked in multiple high-speed and high-definition videos, while Particle Image Velocimetry is used to detail ground motion in response to the buried blasts. In addition, after each blast the emplacement position of all analog ballistics was mapped with respect to the blast location. Preliminary results show the acceleration history of ballistics to be quite variable, from very short and relatively simple acceleration coupled with ground motion, to more complex, multi-stage accelerations possibly affected not only by the initial ground motion but also by variable coupling with the gas-particle mixture generated by the blasts. Further analysis of the experimental results is expected to provide new interpretative tools for ballistic deposits and better hazard assessment, with particular emphasis for the case of vent-opening eruptions driven by explosive gas expansion beneath loose debris.

Geohydrology of the Gallup's Quarry area, Plainfield, Connecticut

USGS Publications Warehouse

Melvin, Robert L.; Stone, Janet Radway; Craft, Patrick A.; Lane, John W.

1995-01-01

The geohydrology of the Gallup's Quarry area in Plainfield, Connecticut was characterized by the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency, to provide a preliminary framework for future remedial efforts. Gallup's Quarry, an inactive sand and gravel pit, was the site of unregulated disposal of an unknown volume of chemical wastes from at least the summer of 1977 until January 1978. Existing information collected for the Connecticut Department of Environmental Protection during 1978-82 showed that ground water beneath Gallup's Quarry and adjacent land to the northwest was contaminated by organic and inorganic compounds. There is also some evidence for contamination of Mill Brook, which is located north and northwest of the disposal areas. Geologic mapping and subsurface data show that unconsolidated surficial materials up to 90 feet thick overlie fractured crystalline bedrock in most of the Gallup's Quarry area. The surficial materials consist primarily of stratified drift and till. Texture changes vertically and laterally within the stratified drift; grain size ranges from very coarse to fine. Till blankets the bedrock surface beneath the stratified drift and is a few feet to as much as 25 feet thick. Bedrock is exposed at land surface in a hill in the southeastern part of the quarry and slopes to depths of up to 90 feet beneath the area west and north of the disposal sites. The bedrock is a dark, fine-grained, fractured and jointed blastomylonite and hornblende gneiss of the Quinebaug Formation. It is likely that a west- northwest-trending fault is present in the bedrock beneath Gallup's Quarry; this fault, if present, may provide a preferential pathway for ground-water flow and contaminant transport. The principal horizontal direction of ground-water flow and movement of dissolved contaminants in the stratified drift was to the northwest of the waste-disposal areas toward Mill Brook in 1978. Estimates of average annual recharge based on regional analyses for 1978-91 are 30 inches in areas where stratified drift are exposed and 9.6 inches in areas where till and crystalline bedrock are exposed. The hydraulic conductivity of the coarse-grained stratified drift, identified in earlier U.S. Geological Survey studies as part of an aquifer capable of yielding large quantities of water, may be several hundred feet per day. The hydraulic conductivity of the till, based on regional information, is likely 0.04 to 24 feet per day. More detailed geohydrologic information is required to develop effective remedial programs at Gallup's Quarry, particularly in the areas north and west of the waste-disposal areas. Detailed subsurface geologic mapping and definition of head distribution and other hydraulic properties of each geohydrologic unit would indicate directions and rates of ground-water flow. Most importantly, the present extent of contamination of water and sediments throughout the area will have to be determined.

Gas Production Strategy of Underground Coal Gasification Based on Multiple Gas Sources

PubMed Central

Tianhong, Duan; Zuotang, Wang; Limin, Zhou; Dongdong, Li

2014-01-01

To lower stability requirement of gas production in UCG (underground coal gasification), create better space and opportunities of development for UCG, an emerging sunrise industry, in its initial stage, and reduce the emission of blast furnace gas, converter gas, and coke oven gas, this paper, for the first time, puts forward a new mode of utilization of multiple gas sources mainly including ground gasifier gas, UCG gas, blast furnace gas, converter gas, and coke oven gas and the new mode was demonstrated by field tests. According to the field tests, the existing power generation technology can fully adapt to situation of high hydrogen, low calorific value, and gas output fluctuation in the gas production in UCG in multiple-gas-sources power generation; there are large fluctuations and air can serve as a gasifying agent; the gas production of UCG in the mode of both power and methanol based on multiple gas sources has a strict requirement for stability. It was demonstrated by the field tests that the fluctuations in gas production in UCG can be well monitored through a quality control chart method. PMID:25114953

Gas production strategy of underground coal gasification based on multiple gas sources.

PubMed

Tianhong, Duan; Zuotang, Wang; Limin, Zhou; Dongdong, Li

2014-01-01

To lower stability requirement of gas production in UCG (underground coal gasification), create better space and opportunities of development for UCG, an emerging sunrise industry, in its initial stage, and reduce the emission of blast furnace gas, converter gas, and coke oven gas, this paper, for the first time, puts forward a new mode of utilization of multiple gas sources mainly including ground gasifier gas, UCG gas, blast furnace gas, converter gas, and coke oven gas and the new mode was demonstrated by field tests. According to the field tests, the existing power generation technology can fully adapt to situation of high hydrogen, low calorific value, and gas output fluctuation in the gas production in UCG in multiple-gas-sources power generation; there are large fluctuations and air can serve as a gasifying agent; the gas production of UCG in the mode of both power and methanol based on multiple gas sources has a strict requirement for stability. It was demonstrated by the field tests that the fluctuations in gas production in UCG can be well monitored through a quality control chart method.

Use of computer systems and process information for blast furnace operations at U. S. Steel, Gary Works

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sherman, G.J.; Zmierski, M.L.

1994-09-01

US Steel Iron Producing Div. consists of four operating blast furnaces ranging in process control capabilities from 1950's and 1960's era hardware to state of the art technology. The oldest control system consists of a large number of panels containing numerous relays, indicating lights, selector switches, push buttons, analog controllers, strip chart recorders and annunciators. In contrast, the state of the art control system utilizes remote I/O, two sets of redundant PLC's, redundant charge director computer, redundant distributed control system, high resolution video-graphic display system and supervisory computer for real-time data acquisition. Process data are collected and archived on twomore » DEC VAX computers, one for No. 13 blast furnace and the other for the three south end furnaces. Historical trending, data analysis and reporting are available to iron producing personnel through terminals and PC's connected directly to the systems, dial-up modems and various network configurations. These two machines are part of the iron producing network which allows them to pass and receive information from each other as well as numerous other sources throughout the division. This configuration allows personnel to access most pertinent furnace information from a single source. The basic objective of the control systems is to charge raw materials to the top of the furnace at aim weights and sequence, while maintaining blast conditions at the bottom of the furnace at required temperature, pressure and composition. Control changes by the operators are primarily supervisory based on review of system generated plots and tables.« less

Rapidly evolving R genes in diverse grass species confer resistance to rice blast disease

PubMed Central

Yang, Sihai; Li, Jing; Zhang, Xiaohui; Zhang, Qijun; Huang, Ju; Chen, Jian-Qun; Hartl, Daniel L.; Tian, Dacheng

2013-01-01

We show that the genomes of maize, sorghum, and brachypodium contain genes that, when transformed into rice, confer resistance to rice blast disease. The genes are resistance genes (R genes) that encode proteins with nucleotide-binding site (NBS) and leucine-rich repeat (LRR) domains (NBS–LRR proteins). By using criteria associated with rapid molecular evolution, we identified three rapidly evolving R-gene families in these species as well as in rice, and transformed a randomly chosen subset of these genes into rice strains known to be sensitive to rice blast disease caused by the fungus Magnaporthe oryzae. The transformed strains were then tested for sensitivity or resistance to 12 diverse strains of M. oryzae. A total of 15 functional blast R genes were identified among 60 NBS–LRR genes cloned from maize, sorghum, and brachypodium; and 13 blast R genes were obtained from 20 NBS–LRR paralogs in rice. These results show that abundant blast R genes occur not only within species but also among species, and that the R genes in the same rapidly evolving gene family can exhibit an effector response that confers resistance to rapidly evolving fungal pathogens. Neither conventional evolutionary conservation nor conventional evolutionary convergence supplies a satisfactory explanation of our findings. We suggest a unique mechanism termed “constrained divergence,” in which R genes and pathogen effectors can follow only limited evolutionary pathways to increase fitness. Our results open avenues for R-gene identification that will help to elucidate R-gene vs. effector mechanisms and may yield new sources of durable pathogen resistance. PMID:24145399

Waveform inversion of acoustic waves for explosion yield estimation

DOE PAGES

Kim, K.; Rodgers, A. J.

2016-07-08

We present a new waveform inversion technique to estimate the energy of near-surface explosions using atmospheric acoustic waves. Conventional methods often employ air blast models based on a homogeneous atmosphere, where the acoustic wave propagation effects (e.g., refraction and diffraction) are not taken into account, and therefore, their accuracy decreases with increasing source-receiver distance. In this study, three-dimensional acoustic simulations are performed with a finite difference method in realistic atmospheres and topography, and the modeled acoustic Green's functions are incorporated into the waveform inversion for the acoustic source time functions. The strength of the acoustic source is related to explosionmore » yield based on a standard air blast model. The technique was applied to local explosions (<10 km) and provided reasonable yield estimates (<~30% error) in the presence of realistic topography and atmospheric structure. In conclusion, the presented method can be extended to explosions recorded at far distance provided proper meteorological specifications.« less

Waveform inversion of acoustic waves for explosion yield estimation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, K.; Rodgers, A. J.

We present a new waveform inversion technique to estimate the energy of near-surface explosions using atmospheric acoustic waves. Conventional methods often employ air blast models based on a homogeneous atmosphere, where the acoustic wave propagation effects (e.g., refraction and diffraction) are not taken into account, and therefore, their accuracy decreases with increasing source-receiver distance. In this study, three-dimensional acoustic simulations are performed with a finite difference method in realistic atmospheres and topography, and the modeled acoustic Green's functions are incorporated into the waveform inversion for the acoustic source time functions. The strength of the acoustic source is related to explosionmore » yield based on a standard air blast model. The technique was applied to local explosions (<10 km) and provided reasonable yield estimates (<~30% error) in the presence of realistic topography and atmospheric structure. In conclusion, the presented method can be extended to explosions recorded at far distance provided proper meteorological specifications.« less

Visual Analysis as a design and decision-making tool in the development of a quarry

Treesearch

Randall Boyd Fitzgerald

1979-01-01

In order to obtain local and state government approvals, an environmental impact analysis of the mining and reclamation of a proposed hard rock quarry was required. High visibility of the proposed mining area from the adjacent community required a visual impact analysis in the planning and design of the project. The Visual Analysis defined design criteria for the...

Floodplain/wetlands assessment for the interceptor trench field study near the Weldon Spring Quarry, Weldon Spring Site, Missouri

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Lonkhuyzen, R.A.

1999-12-15

The US Department of Energy proposes to construct a groundwater interceptor trench near the Weldon Spring Quarry at the Weldon Spring Site in Missouri. The trench would be located near two palustrine wetland areas. Impacts to wetland hydrology and biotic communities are expected to be negligible. No long-term adverse impacts to floodplains are expected.

Piedra Pajarilla: A candidate for nomination as Global Heritage Stone Resource from Spain

NASA Astrophysics Data System (ADS)

Pereira, Dolores; Gimeno, Ana; del Barrio, Santiago

2013-04-01

Piedra Pajarilla is a tourmaline bearing leucogranite outcropping at Martinamor, near Salamanca, Spain. It is part of the Hercynian granitic chain in the Spanish Central System. The stone received the local name "Piedra Pajarilla", meaning "Little Bird Stone" due to the shape of the many tourmaline aggregates that are the main visual feature of the rock. This local name has been extrapolated to every granitic stone used in the area, even if they differ significantly in mineralogy, and as recently tested in physical and mechanical properties as well. Here we present the nomination of Piedra Pajarilla as a suitable "Global Heritage Stone Resource". This stone ideally fits the newly proposed designation as it has been used since Roman times in Salamanca (Spain) and since the Middle Ages in the construction of major historic buildings, including both the Old and New Cathedrals, and many additional churches, castles and walls in the Salamanca area. Salamancás historic city core has been granted UNESCO World Heritage status in 1988, and all associated buildings, monuments and pedestrian streets are constructed from original materials. One of utilised materials, Piedra Pajarilla, was quarried for centuries from the immediate area. It was also the preferred building stone of many internationally renowned architects of Spanish origin during the 18th and 19th centuries especially involved in reconstruction following the Lisbon earthquake. Although the associated quarries are no longer active, the Piedra Pajarilla quarry sites remain relatively undisturbed and accessible. A renewal of quarrying is consequently feasible if additional stone supplies are required for heritage restoration. Thus there is also a need to preserve these historic quarries in anticipation of such work. The importance of Salamanca as emblematic heritage makes the historic stone quarries worthwhile to preserve as well. At the same time, Piedra Pajarilla can be considered as the first of several natural stones that can contribute to the denomination of a "Global Heritage Stone Province", as a suite of associated stone resources have been utilised in the historical buildings of Salamanca.

30 CFR 57.6405 - Firing devices.

Code of Federal Regulations, 2013 CFR

2013-07-01

... sufficient current to energize all electric detonators to be fired with the type of circuits used. Storage or dry cell batteries are not permitted as power sources. (b) Blasting machines shall be tested, repaired...

30 CFR 57.6405 - Firing devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... sufficient current to energize all electric detonators to be fired with the type of circuits used. Storage or dry cell batteries are not permitted as power sources. (b) Blasting machines shall be tested, repaired...

30 CFR 57.6405 - Firing devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... sufficient current to energize all electric detonators to be fired with the type of circuits used. Storage or dry cell batteries are not permitted as power sources. (b) Blasting machines shall be tested, repaired...

30 CFR 57.6405 - Firing devices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... sufficient current to energize all electric detonators to be fired with the type of circuits used. Storage or dry cell batteries are not permitted as power sources. (b) Blasting machines shall be tested, repaired...

30 CFR 57.6405 - Firing devices.

Code of Federal Regulations, 2012 CFR

2012-07-01

... sufficient current to energize all electric detonators to be fired with the type of circuits used. Storage or dry cell batteries are not permitted as power sources. (b) Blasting machines shall be tested, repaired...

Simulation and scaling analysis of a spherical particle-laden blast wave

NASA Astrophysics Data System (ADS)

Ling, Y.; Balachandar, S.

2018-02-01

A spherical particle-laden blast wave, generated by a sudden release of a sphere of compressed gas-particle mixture, is investigated by numerical simulation. The present problem is a multiphase extension of the classic finite-source spherical blast-wave problem. The gas-particle flow can be fully determined by the initial radius of the spherical mixture and the properties of gas and particles. In many applications, the key dimensionless parameters, such as the initial pressure and density ratios between the compressed gas and the ambient air, can vary over a wide range. Parametric studies are thus performed to investigate the effects of these parameters on the characteristic time and spatial scales of the particle-laden blast wave, such as the maximum radius the contact discontinuity can reach and the time when the particle front crosses the contact discontinuity. A scaling analysis is conducted to establish a scaling relation between the characteristic scales and the controlling parameters. A length scale that incorporates the initial pressure ratio is proposed, which is able to approximately collapse the simulation results for the gas flow for a wide range of initial pressure ratios. This indicates that an approximate similarity solution for a spherical blast wave exists, which is independent of the initial pressure ratio. The approximate scaling is also valid for the particle front if the particles are small and closely follow the surrounding gas.

Simulation and scaling analysis of a spherical particle-laden blast wave

NASA Astrophysics Data System (ADS)

Ling, Y.; Balachandar, S.

2018-05-01

A spherical particle-laden blast wave, generated by a sudden release of a sphere of compressed gas-particle mixture, is investigated by numerical simulation. The present problem is a multiphase extension of the classic finite-source spherical blast-wave problem. The gas-particle flow can be fully determined by the initial radius of the spherical mixture and the properties of gas and particles. In many applications, the key dimensionless parameters, such as the initial pressure and density ratios between the compressed gas and the ambient air, can vary over a wide range. Parametric studies are thus performed to investigate the effects of these parameters on the characteristic time and spatial scales of the particle-laden blast wave, such as the maximum radius the contact discontinuity can reach and the time when the particle front crosses the contact discontinuity. A scaling analysis is conducted to establish a scaling relation between the characteristic scales and the controlling parameters. A length scale that incorporates the initial pressure ratio is proposed, which is able to approximately collapse the simulation results for the gas flow for a wide range of initial pressure ratios. This indicates that an approximate similarity solution for a spherical blast wave exists, which is independent of the initial pressure ratio. The approximate scaling is also valid for the particle front if the particles are small and closely follow the surrounding gas.

Volcanic Lightning, Pyroclastic Density Currents, Ballistic Fall, Vent Tremor, and One Very Loud Blast: Acoustic Analysis of the 14 July 2013 Vulcanian Eruption at Tungurahua, Ecuador.

NASA Astrophysics Data System (ADS)

Anderson, J.; Johnson, J. B.; Steele, A. L.; Anzieta, J. C.; Ortiz, H. D.; Hall, M. L.; Ruiz, M. C.

2014-12-01

Acoustic recordings reveal a variety of volcanic activities during an exceptionally loud vulcanian eruption at Tungurahua. A period of several months of mild surface activity came to an abrupt end with the emission of a powerful blast wave heard at least 180 km away. Sensors 2080 m from the vent recorded a stepped rise to its maximum overpressure of 1220 Pa (corresponding to a sound pressure level of 156 dB) and its unusually long dominant period of 5.6 s. We discuss source processes that produced the blast wave, considering that wave propagation could be nonlinear near the vent because of high overpressures. More than an hour of acoustic activity was recorded after the blast wave, including sound from falling ballistics, reflections of the blast wave from nearby mountains, pyroclastic density currents, and acoustic tremor at the vent. Glitches in the acoustic records related to plume lightning were also serendipitously observed, although thunder could not be unambiguously identified. We discuss acoustic signatures of falling ballistics and pyroclastic density currents and how array-style deployments and analytic methods can be used to reveal them. Placement of sensors high on the volcano's slopes facilitated resolving these distinct processes. This study demonstrates that near-vent, array-style acoustic installations can be used to monitor various types of volcanic activity.

Power-Law Template for IR Point Source Clustering

NASA Technical Reports Server (NTRS)

Addison, Graeme E.; Dunkley, Joanna; Hajian, Amir; Viero, Marco; Bond, J. Richard; Das, Sudeep; Devlin, Mark; Halpern, Mark; Hincks, Adam; Hlozek, Renee;

Optimization of Sinter Plant Operating Conditions Using Advanced Multivariate Statistics: Intelligent Data Processing

NASA Astrophysics Data System (ADS)

Fernández-González, Daniel; Martín-Duarte, Ramón; Ruiz-Bustinza, Íñigo; Mochón, Javier; González-Gasca, Carmen; Verdeja, Luis Felipe

2016-08-01

Blast furnace operators expect to get sinter with homogenous and regular properties (chemical and mechanical), necessary to ensure regular blast furnace operation. Blends for sintering also include several iron by-products and other wastes that are obtained in different processes inside the steelworks. Due to their source, the availability of such materials is not always consistent, but their total production should be consumed in the sintering process, to both save money and recycle wastes. The main scope of this paper is to obtain the least expensive iron ore blend for the sintering process, which will provide suitable chemical and mechanical features for the homogeneous and regular operation of the blast furnace. The systematic use of statistical tools was employed to analyze historical data, including linear and partial correlations applied to the data and fuzzy clustering based on the Sugeno Fuzzy Inference System to establish relationships among the available variables.

A multidisciplinary study of the Lower Cretaceous Cedar Mountain Formation, Mussentuchit Wash, Utah: a determination of the paleoenvironment and paleoecology of the Eolambia caroljonesa dinosaur quarry

USGS Publications Warehouse

Garrison, J.R.; Brinkman, D.; Nichols, D.J.; Layer, P.; Burge, D.; Thayn, D.

2007-01-01

A quarry within the Cedar Mountain Formation in Mussentuchit Wash, Emery County, Utah, produced a fossil assemblage containing the remains of at least eight juvenile iguanodontid dinosaurs (Eolambia caroljonesa). The Cedar Mountain Formation lies stratigraphically between the Tithonian-Berriasian (Upper Jurassic) Brushy Basin Member of the Morrison Formation and the Cenomanian (Upper Cretaceous) Dakota Formation. Detailed stratigraphic, sedimentological, geochronological, palynological, and paleontological data have been collected along a measured section at the site of the Cifelli #2 Eolambia caroljonesa Quarry. These data provide a chronostratigraphic and a biostratigraphic framework for the Cedar Mountain Formation and allow a detailed reconstruction of the paleoenvironment and the paleoecology of the local paleogeographic area from which E. caroljonesa have been recovered. Three 40Ar/39Ar ages ranging from 96.7 to 98.5 Ma have been obtained three stratigraphically distinct altered volcanic ash layers within the Mussentuchit Member, one of which passes through the E. caroljonesa quarry, that indicate that the quarry is latest Albian in age and that the stratigraphic boundary between the Mussentuchit Member of the Cedar Mountain Formation and the overlying Dakota Formation is at or near the Albian/Cenomanian boundary. Sedimentological and biostratigraphic data suggest that significant long-term and short-term climatic changes are recorded in the Cedar Mountain Formation. During deposition of the lower part of the formation, climatic conditions were warm and arid to semi-arid. During deposition of the upper part of the formation, conditions became more humid. The progressive change in climatic conditions was probably related to the transgression of the Mowry Sea from the north. Cyclic sedimentation in the Mussentuchit Member suggests high-frequency changes from wet to dry periods. ?? 2007 Elsevier Ltd. All rights reserved.

Geology of the Carnegie museum dinosaur quarry site of Diplodocus carnegii, Sheep Creek, Wyoming

USGS Publications Warehouse

Brezinski, D.K.; Kollar, A.D.

2008-01-01

The holotype of Diplodocus carnegii Hatcher, 1901, consists of a partial skeleton (CM 84) that was recovered, along with a second partial skeleton of the same species (CM 94), from the upper 10 m of the Talking Rock facies of the Brushy Basin Member of the Morrison Formation exposed along Bone Quarry Draw, a tributary of Sheep Creek in Albany County, Wyoming. A composite measured section of the stratigraphic interval exposed adjacent to the quarry indicates that the Brushy Basin Member in this area is a stacked succession of lithofacies consisting of hackly, greenish gray, calcareous mudstone and greenish brown, dense, fine-grained limestone. The more erosion resistant limestone layers can be traced over many hundreds of meters. Thus, these strata do not appear to represent a highly localized deposit such as a stream channel, oxbow lake, or backwater pond. The Sheep Creek succession is interpreted as representing a clastic-dominated lake where high turbidity and sediment influx produced deposition of calcareous mudstone. During drier periods the lake's turbidity decreased and limestone and dolomite precipitation replaced mud deposition. Microkarsting at the top of some limestone/ dolomite layers suggests subaerial deposition may have prevailed during these dry episodes. The quarry of D. carnegii was excavated within the top strata of one of the numerous intervals of hackly, greenish gray, calcareous mudstone that represent an ephemeral freshwater lake. The quarry strata are directly overlain by 0.3 m of dolomite-capped limestone that was deposited shortly after interment of D. carnegii in the lake mudstones. The close vertical proximity of the overlying limestone to the skeleton's stratigraphic: level suggests that the animal's carcass may have been buried beneath the drying lake deposits during a period of decreased rainfall.

The effect of pH on metal accumulation in two Alyssum species.

PubMed

Kukier, Urszula; Peters, Carinne A; Chaney, Rufus L; Angle, J Scott; Roseberg, Richard J

2004-01-01

Nickel phytoextraction using hyperaccumulator plants offers a potential for profit while decontaminating soils. Although soil pH is considered a key factor in metal uptake by crops, little is known about soil pH effects on metal uptake by hyperaccumulator plants. Two Ni and Co hyperaccumulators, Alyssum murale and A. corsicum, were grown in Quarry muck (Terric Haplohemist) and Welland (Typic Epiaquoll) soils contaminated by a Ni refinery in Port Colborne, Ontario, Canada, and in the serpentine Brockman soil (Typic Xerochrepts) from Oregon, USA. Soils were acidified and limed to cover pH from strongly acidic to mildly alkaline. Alyssum grown in both industrially contaminated soils exhibited increased Ni concentration in shoots as soil pH increased despite a decrease in water-soluble soil Ni, opposite to that seen with agricultural crop plants. A small decrease in Alyssum shoot Ni concentration as soil pH increased was observed in the serpentine soil. The highest fraction of total soil Ni was phytoextracted from Quarry muck (6.3%), followed by Welland (4.7%), and Brockman (0.84%). Maximum Ni phytoextraction was achieved at pH 7.3, 7.7, and 6.4 in the Quarry, Welland, and Brockman soils, respectively. Cobalt concentrations in shoots increased with soil pH increase in the Quarry muck, but decreased in the Welland soil. Plants extracted 1.71, 0.83, and 0.05% of the total soil Co from Welland, Quarry, and Brockman, respectively. The differences in uptake pattern of Ni and Co by Alyssum from different soils and pH were probably related to the differences in organic matter and iron contents of the soils.

Noise-Induced Hearing Loss Among Quarry Workers in a North-Eastern State of Malaysia: A Study on Knowledge, Attitude and Practice

PubMed Central

Ismail, Ahmad Filza; Daud, Aziah; Ismail, Zaliha; Abdullah, Baharudin

2013-01-01

Objectives Noise is known to be one of the environmental and occupational hazards listed in the Factory and Machinery Act 1967. Quarries with loud deafening sounds from trucks and machineries pose the risk of noise-induced hearing loss to workers. This study was designed to assess the knowledge, attitude and practice towards noise-induced hearing loss and to determine the prevalence of noise-induced hearing loss and its associated factors among quarry workers in a north-eastern state of Malaysia. Methods A cross-sectional study was conducted at six quarries in a north-eastern state of Malaysia, with 97 consented respondents who answered a validated version of a questionnaire and underwent pure tone audiogram. The respondents were male, aged between 18 to 50 years, working in the quarry area for at least 6-months duration with no family history of ear diseases. Results The mean percentage scores of knowledge, attitude and practice were 44 (11), 70 (10) and 28 (16) percent, respectively. The prevalence of noise-induced hearing loss was found to be 57 (95% CI: 47, 67) with 46 (84%) having mild and moderate noise-induced hearing loss, and 34 (62%) involved both ears. Multiple logistic regressions showed that age and practice score were the associated factors with odd ratios of 1.1 (95% CI: 1.1, 1.2; p<0.001) and 0.9 (95% CI: 0.8, 1.0; p=0.008), respectively. Conclusion The knowledge, attitude and practice scores of the respondents were poor and the high prevalence of noise-induced hearing loss was contributed by factors such as poor practice and old age. PMID:24044059

U-series dating of the Late Pleistocene mammalian fauna from Wood Quarry (Steetley), Nottinghamshire, UK

NASA Astrophysics Data System (ADS)

Pike, A. W. G.; Eggins, S.; Grün, R.; Hedges, R. E. M.; Jacobi, R. M.

2005-01-01

We present the U-series dating of bones from Wood Quarry (Steetley Quarry Cave) using the diffusion-adsorption model to account for uranium uptake. The results give a weighted mean date of 66.8 ± 3.0 kyr, placing this assemblage within or just before Marine Oxygen Isotope Stage 4. The fauna is thought to correlate with the Banwell Bone Cave mammal assemblage-zone of the Early Devensian in Britain. Our results support the idea that this assemblage-zone immediately precedes the assemblage represented nearby at Pin Hole in Creswell Crags which is contemporary with the Mid-Devensian and correlates with MIS 3. Our dates, and dates for the Banwell Bone Cave mammal assemblage-zone from Stump Cross Cavern and evidence from other sites may indicate a longevity for this fauna.

Block Volume Estimation from the Discontinuity Spacing Measurements of Mesozoic Limestone Quarries, Karaburun Peninsula, Turkey

PubMed Central

Elci, Hakan; Turk, Necdet

2014-01-01

Block volumes are generally estimated by analyzing the discontinuity spacing measurements obtained either from the scan lines placed over the rock exposures or the borehole cores. Discontinuity spacing measurements made at the Mesozoic limestone quarries in Karaburun Peninsula were used to estimate the average block volumes that could be produced from them using the suggested methods in the literature. The Block Quality Designation (BQD) ratio method proposed by the authors has been found to have given in the same order of the rock block volume to the volumetric joint count (J v) method. Moreover, dimensions of the 2378 blocks produced between the years of 2009 and 2011 in the working quarries have been recorded. Assuming, that each block surfaces is a discontinuity, the mean block volume (V b), the mean volumetric joint count (J vb) and the mean block shape factor of the blocks are determined and compared with the estimated mean in situ block volumes (V in) and volumetric joint count (J vi) values estimated from the in situ discontinuity measurements. The established relations are presented as a chart to be used in practice for estimating the mean volume of blocks that can be obtained from a quarry site by analyzing the rock mass discontinuity spacing measurements. PMID:24696642

A novel environmental restoration method for an abandoned limestone quarry with a deep open pit and steep palisades: a case study

PubMed Central

Wang, Hanxun; Bai, Xueliang; Shi, Lei

2018-01-01

In general, exploitation of rock materials, such as limestone or granite exploitation, can cause serious damage to the environment near a mine area. With economic development and the ever-increasing demand for ore resources, mining activities have induced very serious environmental issues in China. Therefore, environmental restoration work around mines in China is urgently required. This study explores the Chuankou open-pit limestone quarry in Tongchuan City, Shaanxi Province, Northwest China, as the engineering case. The environmental issues caused by over 40 years of limestone exploitation, including land degradation, land occupation, dust pollution and potential geological disasters, were investigated. Combining the characteristics of this quarry with a summary of previous studies on environmental restoration work, this paper proposes a novel and systematic method that was comprehensively carried out through engineering and revegetation measures. The engineering measure, that is, the construction of an artificial slope by using local abandoned construction materials, solved the environmental problems in this quarry and provided site conditions favourable for revegetation. The revegetation measure restored the local ecosystem. This method provides both a new idea for the sustainable development of a mining area and a useful reference for analogous engineering cases. PMID:29892461

Block volume estimation from the discontinuity spacing measurements of mesozoic limestone quarries, Karaburun Peninsula, Turkey.

PubMed

Elci, Hakan; Turk, Necdet

2014-01-01

Block volumes are generally estimated by analyzing the discontinuity spacing measurements obtained either from the scan lines placed over the rock exposures or the borehole cores. Discontinuity spacing measurements made at the Mesozoic limestone quarries in Karaburun Peninsula were used to estimate the average block volumes that could be produced from them using the suggested methods in the literature. The Block Quality Designation (BQD) ratio method proposed by the authors has been found to have given in the same order of the rock block volume to the volumetric joint count (J(v)) method. Moreover, dimensions of the 2378 blocks produced between the years of 2009 and 2011 in the working quarries have been recorded. Assuming, that each block surfaces is a discontinuity, the mean block volume (V(b)), the mean volumetric joint count (J(vb)) and the mean block shape factor of the blocks are determined and compared with the estimated mean in situ block volumes (V(in)) and volumetric joint count (J(vi)) values estimated from the in situ discontinuity measurements. The established relations are presented as a chart to be used in practice for estimating the mean volume of blocks that can be obtained from a quarry site by analyzing the rock mass discontinuity spacing measurements.

Abandoned mines and their impact on the environment: Case studies from Franklin and Sterling Mines, NJ and Rondout Quarry, NY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolkas, M.M.; Nehru, C.E.

1995-09-01

Water logged abandoned mines have an impact on the environment. In this project we selected abandoned mines from two sets of different ore bodies to learn about their environmental impact. Franklin and Sterling Pb-Zn mines, NJ and the limestone quarry in Rondout formation, NY were selected as case study examples. In the Pb-Zn mines metalimestone is the country rock and in the Rondout quarry limestone is the country rock. Soil water samples from selected strategic locations were analyzed for toxic and related heavy metal elements such as Pb, Zn, Cd, Cr and U. The levels of concentrations of these elementsmore » varied from one location to another according to the chemistry of the ore body and the ground movement throughout the area. In particular Cd, Cr and U concentration were variable from Franklin to Sterling mine. However, in the Rondout limestone (cement) quarry, higher concentrations of Cr and lower concentrations of Pb and Zn were noted. We conclude that ore body chemistry, mine dumps and tailing contaminated ponds along with the ground water movement throughout the area have an impact on the ground water and nearby river/stream contaminant chemistry in the areas.« less

Provenance of white marbles from the nabatean sites of Qase Al Bint and colonnaded street baths at Petra, Jordan

NASA Astrophysics Data System (ADS)

Abu-Jaber, Nizar; al-Saad, Ziad; Shiyyab, Adnan; Degryse, Patrick

Intercultural relations and trade are important components of understanding of historical interrelationships between regions and cultures. One of the most interesting objects of trade is stone, because of the expense and difficulty of its transport. Thus, the source of marble used in the Nabatean city of Petra was investigated using established petrological, geochemical and isotopic analyses. Specifically, marble from Qasr al Bint and the Colonnaded Street baths were sampled and investigated. The results of these analyses show that the marbles came from sources in Asia Minora and Greece. The most likely sources of the marble are the quarries of Thasos, Penteli, Prokennesos and Dokimeion. The choice of marble followed the desired utilitarian and aesthetic function of the stone. These results show that active trade in stone was part of the cultural interaction of the period.

Self-similar relativistic blast waves with energy injection

NASA Astrophysics Data System (ADS)

van Eerten, Hendrik

2014-08-01

A sufficiently powerful astrophysical source with power-law luminosity in time will give rise to a self-similar relativistic blast wave with a reverse shock travelling into the ejecta and a forward shock moving into the surrounding medium. Once energy injection ceases and the last energy is delivered to the shock front, the blast wave will transit into another self-similar stage depending only on the total amount of energy injected. I describe the effect of limited duration energy injection into environments with density depending on radius as a power law, emphasizing optical/X-ray Gamma-ray Burst afterglows as applications. The blast wave during injection is treated analytically, the transition following last energy injection with one-dimensional simulations. Flux equations for synchrotron emission from the forward and reverse shock regions are provided. The reverse shock emission can easily dominate, especially with different magnetizations for both regions. Reverse shock emission is shown to support both the reported X-ray and optical correlations between afterglow plateau duration and end time flux, independently of the luminosity power-law slope. The model is demonstrated by application to bursts 120521A and 090515, and can accommodate their steep post-plateau light-curve slopes.

Building stones of our Nation's Capital

USGS Publications Warehouse

Withington, Charles F.

1975-01-01

The buildings of our Nation's Capital serve as an unusual geologic display, for the city has been constructed with rocks from quarries throughout the United States and many distant lands. Each building is a unique museum that not only displays the important features of various stones and the geologic environment in which they were formed, but also serves as an historic witness to the city's growth and to the development of its architecture. This booklet describes the source and appearance of the stones used in Washington, D.C.; it includes a map and a walking guide to assist the visitor in examining them.

Integrated Verification Experiment data collected as part of the Los Alamos National Laboratory`s Source Region Program. Appendix D: Ionospheric measurements for IVEs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fitzgerald, T.J.; Carlos, R.C.; Argo, P.E.

As part of the integrated verification experiment (IVE), we deployed a network of hf ionospheric sounders to detect the effects of acoustic waves generated by surface ground motion following underground nuclear tests at the Nevada Test Site. The network sampled up to four geographic locations in the ionosphere from almost directly overhead of the surface ground zero out to a horizontal range of 60 km. We present sample results for four of the IVEs: Misty Echo, Texarkana, Mineral Quarry, and Bexar.

The OSMATER project: promotion of stone materials from the Verbano-Cusio-Ossola region (Italy) and the Canton Ticino (Switzerland).

NASA Astrophysics Data System (ADS)

Cavallo, Alessandro; Antonella Dino, Giovanna

2013-04-01

The OSMATER (sub-Alpine Observatory Materials Territory Restoration) project, funded by the Piedmont Region (Italy) and the European Community, involved four Italian scientific bodies (Polytechnic of Turin, University of Turin, University of Milan-Bicocca, University of Bologna) and Switzerland (SUPSI). The aim was to investigate the present and historical quarrying and processing activities in the cross-border area between the Ossola Valley (Italy) and the Canton Ticino (Switzerland), and the use of dimension stones in local and national architecture. These materials are in many ways a "unique case", for their abundance and lithological variety. In the past, their extraction, processing and application characterized in a decisive way the architectural and constructive culture, both in terms of prestigious architecture and civil buildings, establishing a relationship between "stones and culture", "territory and its resources". In recent years, many of these traditions are losing importance and interest: this results in a loss of knowledge and historical memory, due mainly to the drastic changes in the market. The loss of this knowledge is likely to become irreversible in the short term, with the disappearance of people and social groups depositary of tradition. We can deduce that the creation of an "observatory", like OSMATER, is desirable and essential indeed, if we want to preserve the historical memory of the stone industry of an entire production area. The OSMATER project aimed the knowledge, recovery and enhancement of the architectural and cultural heritage of the cross-border area, through the census and classification of rocks, quarries (both active and historical - since Roman age), monuments and construction techniques typical of the sub-Alpine region, in order to create a documentation centre through a dedicated website. The first phase of the project was devoted to the identification of architectural works built with stone materials, with particular artistic and cultural interest for the study area. The monuments were selected on the basis of both their historical and social importance, and on the basis of stone materials, in order to make coherent proposals for their protection and future restoration projects. A comprehensive list of the quarries was drawn up: each quarry was characterized in terms of lithology, geotechnical properties and exploitation techniques. Where possible, traces of ancient quarrying and processing techniques were investigated and recorded, looking for correlations between stones and architectural heritage. The study area was divided basing on the exploited materials: granites (Baveno, Montorfano, Mergozzo), marbles (Ornavasso and Crevoladossola), "Beola" gneisses (Vogogna, Beura-Villadossola Trontano-Domodossola, Crevoladossola-Montecrestese), "Serizzo" gneisses (Antigorio, Formazza, Simplon, Anzasca and Divedro valleys), carbonatic rocks (Angera-Arona) and greenstones (Bognanco, Vigezzo, Brevettola and Loana valleys). Subsequently each stone from each quarry was characterized: petrography (optical microscopy, XRD, SEM-EDS), geochemistry (whole-rock by ICP-MS), physical and mechanical properties (standard tests and Hg-porosimetry). A comparison between "fresh" stones from the quarries and from the monuments has been realized, searching for correlations to the degradation. The last step was the evaluation of the monumental buildings that could be included into geo-touristic routes (quarry - laboratory - monument), for the enhancement of the local cultural heritage and resources.

Landscape evolution by subglacial quarrying

NASA Astrophysics Data System (ADS)

Ugelvig, Sofie V.; Egholm, David L.; Iverson, Neal R.

2014-05-01

In glacial landscape evolution models, subglacial erosion rates are often related to basal sliding or ice discharge by a power-law. This relation can be justified for bedrock abrasion because rock debris transported in the basal ice drives the erosion. However, a simple relation between rates of sliding and erosion is not well supported when considering models for quarrying of rock blocks from the bed. Iverson (2012) introduced a new subglacial quarrying model that operates from the theory of adhesive wear. The model is based on the fact that cavities, with a high level of bedrock differential stress, form along the lee side of bed obstacles when the sliding velocity is to high to allow for the ice to creep around the obstacles. The erosion rate is quantified by considering the likelihood of rock fracturing on topographic bumps. The model includes a statistical treatment of the bedrock weakness: larger rock bodies have lower strengths since they have greater possibility of containing a large flaw [Jaeger and Cook, 1979]. Inclusion of this effect strongly influences the erosion rates and questions the dominant role of sliding rate in standard models for subglacial erosion. Effective pressure, average bedslope, and bedrock fracture density are primary factors that, in addition to sliding rate, influence the erosion rate of this new quarrying model [Iverson, 2012]. We have implemented the quarrying model in a depth-integrated higher-order ice-sheet model [Egholm et al. 2011], coupled to a model for glacial hydrology. In order to also include the effects of cavitation on the subglacial sliding rate, we use a sliding law proposed by Schoof (2005), which includes an upper limit for the stress that can be supported at the bed. Computational experiments show that the combined influence of pressure, sliding rate and bed slope leads to realistically looking landforms such as U-shaped valleys, cirques, hanging valleys and overdeepenings. Compared to model results using a standard erosion rule, where erosion rate scales with basal sliding, the quarrying model produces valleys that are wider and have more flattened valley floors with several shallow overdeepenings. The overdeepenings are stabilized by hydrology because of the strong influence of effective pressure on quarrying rate. For melt water to escape the overdeepening, the average water pressure must rise as the overdeepening grows, and this keeps the effective pressure low and prevents the overdeepening from growing infinitely. In addition, the strong influence of effective pressure indicates that erosion rate depends strongly on ice thickness. This could associate to sudden jumps in erosion rate and fjord formation along margins that experienced periodic ice sheet configurations in the Quaternary. Egholm, D. L. et al. Modeling the flow of glaciers in steep terrains: The integrated second-order shallow ice approximation (iSOSIA). Journal of Geophysical Research, 116, F02012 (2011). Iverson, N. R. A theory of glacial quarrying for landscape evolution models. Geology, v. 40, no. 8, 679-682 (2012). Schoof, C. The effect of cavitation on glacier sliding. Proc. R. Soc. A , 461, 609-627 (2005). Jaeger, J.C., and Cook, N.G.W. Fundamentals of rock mechanics: New York, Chapman and Hall, 593 p. (1979)

Simulation of ground-water flow in the Vevay Township area, Ingham County, Michigan

USGS Publications Warehouse

Luukkonen, Carol L.; Simard, Andreanne

2004-01-01

Ground water is the primary source of water for domestic, public-supply, and industrial use within the Tri-County region that includes Clinton, Eaton, and Ingham Counties in Michigan. Because of the importance of this ground-water resource, numerous communities, including the city of Mason in Ingham County, have begun local Wellhead Protection Programs. In these programs, communities protect their groundwater resource by identifying the areas that contribute water to production wells and potential sources of contamination, and by developing methods to manage and minimize threats to the water supply. In addition, some communities in Michigan are concerned about water availability, particularly in areas experiencing water-level declines in the vicinity of quarry dewatering operations. In areas where Wellhead Protection Programs are implemented and there are potential threats to the water supply, residents and communities need adequate information to protect the water supply.In 1996, a regional ground-water-flow model was developed by the U.S. Geological Survey to simulate ground-water flow in Clinton, Eaton, and Ingham Counties. This model was developed primarily to simulate the bedrock ground-waterflow system; ground-water flow in the unconsolidated glacial sediments was simulated to support analysis of flow in the underlying bedrock Saginaw aquifer. Since its development in 1996, regional model simulations have been conducted to address protection concerns and water availability questions of local water-resources managers. As a result of these continuing model simulations, additional hydrogeologic data have been acquired in the Tri-County region that has improved the characterization of the simulated ground-water-flow system and improved the model calibration. A major benefit of these updates and refinements is that the regional Tri-County model continues to be a useful tool that improves the understanding of the ground-water-flow system in the Tri-County region, provides local water-resources managers with a means to answer ground-water protection and availability questions, and serves as an example that can be applied in other areas of the state.A refined version of the 1996 Tri-County regional ground-water-flow model, developed in 1997, was modified with local hydrogeologic information in the Vevay Township area in Michigan. This model, updated in 2003 for this study, was used to simulate ground-water flow to address groundwater protection and availability questions in Vevay Township. The 2003 model included refinement of glacial and bedrock hydraulic characteristics, better representation of the degree of connection between the glacial deposits and the underlying Saginaw aquifer, and refinement of the model cell size.The 2003 model was used to simulate regional groundwater flow, to delineate areas contributing recharge and zones of contribution to production wells in the city of Mason, and to simulate the effects of present and possible future withdrawals. The areal extent of the 10- and 40-year areas contributing recharge and the zones of contribution for the city of Mason's production wells encompass about 2.3 and 6.2 square miles, respectively. Simulation results, where withdrawals for quarry operations were represented by one well pumping at 1.6 million gallons per day, indicate that water levels would decline slightly over 1 foot approximately 2 miles from the quarry in the glacial deposits and in the Saginaw aquifer. With a reduction of the local riverbed conductance or removal of local river model cells representing Mud Creek, water-level declines would extend further west of Mud Creek and further to the north, east, and south of the simulated quarry. Simulation results indicate that water withdrawn for quarry dewatering operations would decrease ground-water recharge to nearby Mud Creek, would increase ground-water discharge from Mud Creek, and that local water levels would be lowered as a result.

Development of a rat model for studying blast-induced traumatic brain injury.

PubMed

Cheng, Jingmin; Gu, Jianwen; Ma, Yuan; Yang, Tao; Kuang, Yongqin; Li, Bingcang; Kang, Jianyi

2010-07-15

Blast-induced traumatic brain injury (TBI) has been the predominant cause of neurotrauma in current military conflicts, and it is also emerging as a potential threat in civilian terrorism. The etiology of TBI, however, is poorly understood. Further study on the mechanisms and treatment of blast injury is urgently needed. We developed a unique rat model to simulate blast effects that commonly occur on the battlefield. An electric detonator with the equivalent of 400 mg TNT was developed as the explosive source. The detonator's peak overpressure and impulse of explosion shock determined the explosion intensity in a distance-dependent manner. Ninety-six male adult Sprague-Dawley rats were randomly divided into four groups: 5-cm, 7.5-cm, 10-cm, and control groups. The rat was fixed in a specially designed cabin with an adjustable aperture showing the frontal, parietal, and occipital parts of the head exposed to explosion; the eyes, ears, mouth, and nose were protected by the cabin. After each explosion, we assessed the physiologic, neuropathologic, and neurobehavioral consequences of blast injury. Changes of brain tissue water content and neuron-specific enolase (NSE) expression were detected. The results in the 7.5-cm group show that 87% rats developed apnea, limb seizure, poor appetite, and limpness. Diffuse subarachnoid hemorrhage and edema could be seen within the brain parenchyma, which showed a loss of integrity. Capillary damage and enlarged intercellular and vascular space in the cortex, along with a tattered nerve fiber were observed. These findings demonstrate that we have provided a reliable and reproducible blast-induced TBI model in rats. Copyright 2010 Elsevier B.V. All rights reserved.

The Potential of Streptomyces as Biocontrol Agents against the Rice Blast Fungus, Magnaporthe oryzae (Pyricularia oryzae).

PubMed

Law, Jodi Woan-Fei; Ser, Hooi-Leng; Khan, Tahir M; Chuah, Lay-Hong; Pusparajah, Priyia; Chan, Kok-Gan; Goh, Bey-Hing; Lee, Learn-Han

2017-01-01

Rice is a staple food source for more than three billion people worldwide. However, rice is vulnerable to diseases, the most destructive among them being rice blast, which is caused by the fungus Magnaporthe oryzae (anamorph Pyricularia oryzae ). This fungus attacks rice plants at all stages of development, causing annual losses of approximately 10-30% in various rice producing regions. Synthetic fungicides are often able to effectively control plant diseases, but some fungicides result in serious environmental and health problems. Therefore, there is growing interest in discovering and developing new, improved fungicides based on natural products as well as introducing alternative measures such as biocontrol agents to manage plant diseases. Streptomyce s bacteria appear to be promising biocontrol agents against a wide range of phytopathogenic fungi, which is not surprising given their ability to produce various bioactive compounds. This review provides insight into the biocontrol potential of Streptomyces against the rice blast fungus, M. oryzae . The ability of various S treptomyces spp. to act as biocontrol agents of rice blast disease has been studied by researchers under both laboratory and greenhouse/growth chamber conditions. Laboratory studies have shown that Streptomyces exhibit inhibitory activity against M. oryzae . In greenhouse studies, infected rice seedlings treated with Streptomyces resulted in up to 88.3% disease reduction of rice blast. Studies clearly show that Streptomyces spp. have the potential to be used as highly effective biocontrol agents against rice blast disease; however, the efficacy of any biocontrol agent may be affected by several factors including environmental conditions and methods of application. In order to fully exploit their potential, further studies on the isolation, formulation and application methods of Streptomyces along with field experiments are required to establish them as effective biocontrol agents.

The Potential of Streptomyces as Biocontrol Agents against the Rice Blast Fungus, Magnaporthe oryzae (Pyricularia oryzae)

PubMed Central

Law, Jodi Woan-Fei; Ser, Hooi-Leng; Khan, Tahir M.; Chuah, Lay-Hong; Pusparajah, Priyia; Chan, Kok-Gan; Goh, Bey-Hing; Lee, Learn-Han

2017-01-01

Rice is a staple food source for more than three billion people worldwide. However, rice is vulnerable to diseases, the most destructive among them being rice blast, which is caused by the fungus Magnaporthe oryzae (anamorph Pyricularia oryzae). This fungus attacks rice plants at all stages of development, causing annual losses of approximately 10–30% in various rice producing regions. Synthetic fungicides are often able to effectively control plant diseases, but some fungicides result in serious environmental and health problems. Therefore, there is growing interest in discovering and developing new, improved fungicides based on natural products as well as introducing alternative measures such as biocontrol agents to manage plant diseases. Streptomyces bacteria appear to be promising biocontrol agents against a wide range of phytopathogenic fungi, which is not surprising given their ability to produce various bioactive compounds. This review provides insight into the biocontrol potential of Streptomyces against the rice blast fungus, M. oryzae. The ability of various Streptomyces spp. to act as biocontrol agents of rice blast disease has been studied by researchers under both laboratory and greenhouse/growth chamber conditions. Laboratory studies have shown that Streptomyces exhibit inhibitory activity against M. oryzae. In greenhouse studies, infected rice seedlings treated with Streptomyces resulted in up to 88.3% disease reduction of rice blast. Studies clearly show that Streptomyces spp. have the potential to be used as highly effective biocontrol agents against rice blast disease; however, the efficacy of any biocontrol agent may be affected by several factors including environmental conditions and methods of application. In order to fully exploit their potential, further studies on the isolation, formulation and application methods of Streptomyces along with field experiments are required to establish them as effective biocontrol agents. PMID:28144236

55. QUARRY TILE CUTTERS, SECOND FLOOR, NORTH WING. WORKERS PRESSED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

55. QUARRY TILE CUTTERS, SECOND FLOOR, NORTH WING. WORKERS PRESSED THE CUTTERS INTO SLABS OF CLAY, LIFTED THEM ONTO DRYING BOARDS AND PRESSED THE PLUNGERS TO RELEASE THE CUT TILES. REPRODUCTIONS CUTTERS ARE NOT USED IN PRODUCTION. WOODEN FORMS FOR PRODUCING CLAY SLABS WITH ROLLING PINS REST AGAINST THE WALL. - Moravian Pottery & Tile Works, Southwest side of State Route 313 (Swamp Road), Northwest of East Court Street, Doylestown, Bucks County, PA

Comparative study of modified bitumen binder properties collected from mixing plant and quarry.

NASA Astrophysics Data System (ADS)

Mustafa Kamal, M.; Abu Bakar, R.; Hadithon, K. A.

2017-11-01

Quality control and assurance are essential in pavement construction. In general, the properties of bitumen change as it ages in bulk storage, transport, and storage on site. The minimization of bituminous hardening during storing, transportation and mixing depends on careful control of binder temperature. Hence therefore, bitumen should always be stored and handled at the lowest temperature possible, consistent with efficient use. The objective of the work is to monitor the quality of bitumen samples collected from mixing plant and quarry. Results showed that, samples modified bitumen which collected from quarry showed some adverse effects on rheological properties and physical properties after subjecting to high temperature storage within a period of time. The dynamic stiffness, elastic properties and other common binder properties were deteriorated too. The chemical changes that occurred during storage were analysed using Fourier transform infra-red spectroscopy (FTIR). Thus studies developed an understanding of bitumen ageing in storage.

[SUVA (Swiss Accident Insurance Fund) and silicosis. Silicosis in Switzerland. Development of technological dust control].

PubMed

Bachofen, G

1983-01-01

In Switzerland the technical measures against quartz dust started in 1948 when wet drilling was compulsoryly introduced, initially in underground mining. The miners using the first wet drilling machines had serious problems with water, and only with the introduction of carriage drilling machines in 1963 did the method fully break through. Dust caused by blasting operations and by loading of the resultant material was limited by ventilation and sprinkling of water. In 1966 the first full-face cutting machines were used, and it was necessary to install a dust chamber behind the drill from which dust could be taken to a dust arrester. The problem of dust limitation when using boom cutters at sectional areas of more than 20 sq. meters without a pilot tunnel has not been resolved. Since 1970, dust in quarries and stone-cutter workshops has been successfully combated by the use of exhaust pumps in combination with filters. The use of quartz sand to clean metal pieces (sandblast) was forbidden in 1960. Today, materials of the same value, but quartz-free, are available. In foundries, dust production can be limited by continuous automation and installation of exhaust pumps in moulding units. For more than 30 years now the technical equipment has been available for successful prevention of quartz dust emissions. However, at some plants it is still difficult to persuade the personnel to use the protective equipment.

Geosites of Lithuania as an environment for dwelling of specific biota: geo- and biodiversity interactions

NASA Astrophysics Data System (ADS)

Skridlaite, Grazina; Motiejunaite, Jurga; Jukoniene, Ilona; Prigodina Lukosiene, Ingrida

2016-04-01

Surface of Lithuania and surrounding countries is sculptured by five glaciations, which left behind morainic tills and melt water deposits, modified by erosion and later used for agriculture or overgrown by wild meadows or forests. The glaciations also left numerous erratic boulders and boulder fields that are declared as natural monuments in Lithuania and surrounding countries. Tens of single boulders and boulder fields are included into the Geosites database at the Lithuanian Geological Survey. Though sparse, but of high scientific value, Devonian, Permian, Triassic and Jurassic outcrops and quarries of Lithuania are variably protected. Quaternary scientists attempted to use single erratic boulders, their fields and abundances in tills to imply glacier dynamics. Some erratics came from known localities in Scandinavia and are called indicator boulders because they show the source and directions of ice sheet movements. Huge single boulders (e.g. 7 m long and 6 m high Puntukas, Anyksciai Regional Park) and wild boulder fields are natural monuments and attractive sites for visitors. Outcrops and quarries of Devonian dolomites and gypsium, Permian limestones and Jurassic sandstones widely used for a scientific research are parts of the protected geo-diversity in the Venta and Birzai regional parks, N and NW Lithuania. On the other hand, a large part of the c. 700 species of lichenized and allied fungi and of c. 500 bryophytes known in Lithuania are confined to natural or semi-natural (quarries) rocky habitats. Eight rock-dwelling lichen and nine bryophyte species are included in the Lithuanian Red Data Book, some of them are known from 1-2 localities or are thought to be extinct now. Besides, the recent investigations of dolomite quarries revealed them to be habitats for 7 bryophyte, 8 lichenized and lichenicolous species, previously unknown for Lithuania. One new lichenicolous species was discovered (Khodosovtsev et al., 2012). Some of the newfinds are rare or absent also in the neighbouring countries. In general, protection of geo-diversity coincides well with protection of narrowly specialized cryptogams, e.g. overgrowing of boulder fields with tall herbs and shrubs also has adversary effect on rock-dwelling lichens. Shading of Devonian outcrops and quarries by trees and shrubs may obscure rocky surfaces and destroy lichens, but favour an establishment of sciophyllous bryophytes. No doubt that cleaning of surfaces of single boulders that are well-known nature monuments prevents an establishment and growth of lichens and bryophytes. However, most of the geological monuments which are subjected to cleaning are situated in localities under strong anthropogenic impact and therefore not suitable for settlement of the rare and protected species. Though conservation conflicts arise even when protecting different species of biota, not to mention conservation of bio- versus geo-diversity, most of the conservation measures for the geoheritage in Lithuania are also suitable for rock-inhabiting lichens and bryophytes. Protection status and measures should be negotiated by bio-and geoscientists, and legislation for bio- and geo-diversity protection should be improved. Khodosovtsev, A., Vondrák, J., Naumovich, A., Kocourková, J., Vondráková, O., Motiejūnaitė, J., 2012. Nova Hedwigia, 95(1-2): 211-220.

Power-Law Template for Infrared Point-Source Clustering

NASA Technical Reports Server (NTRS)

Addison, Graeme E; Dunkley, Joanna; Hajian, Amir; Viero, Marco; Bond, J. Richard; Das, Sudeep; Devlin, Mark J.; Halpern, Mark; Hincks, Adam D; Hlozek, Renee;

Traces of the heritage arising from the Macelj sandstone

NASA Astrophysics Data System (ADS)

Golež, Mateja

2014-05-01

The landscape of Southeast Slovenia and its stone heritage principally reveal itself through various Miocene sandstones. The most frequently found type on the borderline between Slovenia and Croatia, i.e. east of Rogatec, is the micaceous-quartz Macelj sandstone. This rock ranges in colour from greenish grey to bluish grey and yellowish, depending on the content of glauconite, which colours it green. In its composition, the rock is a heterogeneous mixture of grains of quartz, dolomite, muscovite, microcline, anorthite and glauconite. The average size of grains is 300μm. In cross-section, they are oblong, semi-rounded or round. The mechanical-physical and durability properties of the Macelj sandstone, which have been characterised pursuant to the applicable standards for natural stone, reveal that the rock exhibits poor resistance to active substances from the atmosphere, particularly in the presence of salt. In the surroundings of Rogatec, there are around 45 abandoned quarries of the Macelj sandstone, which are the result of the exploitation of this mineral resource from the 17th century on. The local quarrymen earned their bread until 1957, when the Kambrus quarry industry closed down. From the original use of this mineral resource as construction and decorative material, the useful value of the Macelj sandstone expanded during the development of the metals industry to the manufacture of large and small grindstones for the needs of the domestic and international market. Therefore, traces of quarrying can not only be seen in the disused quarries, but also in the rich architectural heritage of Rogatec and its surroundings, the stone furniture - from portals, window frames, wells, various troughs, pavements to stone walls - and other. The living quarrying heritage slowly passed into oblivion after World War II, although the analysis of the social image of the people residing in Rogatec and its surroundings revealed that there was an average of one stonemason in every house in the period between both World Wars. Only few masters succeeded in transferring their know-how to their descendants, which is why the local community has been making efforts to include the quarrying and working of the Macelj sandstone in educational workshops that are being carried out at the Open-Air Museum in Rogatec.

Weldon Spring, Missouri, Site Annual Report for Calendar Year 2015 June 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Starr, Ken; Deyo, Yvonne

1.1 Purpose and Scope. This report summarizes the activities, compliance status, annual inspection, and environmental monitoring results from calendar year 2015 for the Weldon Spring, Missouri, Site. The U.S. Department of Energy (DOE) prepares this annual report as part of the site’s long-term surveillance and maintenance (LTS&M) activities, in accordance with the requirements of the Long-Term Surveillance and Maintenance Plan for the Weldon Spring, Missouri, Site (LTS&M Plan) (DOE 2008a) and the Federal Facility Agreement for the Weldon Spring Site (DOE 2006). The Weldon Spring site is a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) site. 1.2 Site Description.more » The Weldon Spring site is located in St. Charles County, Missouri, about 30 miles west of St. Louis, Missouri (Figure 1). The site comprises two geographically distinct, DOE-owned properties: the former Weldon Spring Chemical Plant and Raffinate Pit sites (Chemical Plant) and the former Weldon Spring Quarry (Quarry). The former Chemical Plant is located about 2 miles southwest of the junction of Missouri State Route 94 and Interstate 64. The Quarry is about 4 miles southwest of the former Chemical Plant. Both sites are accessible from Missouri State Route 94. During the early 1940s, the Department of the Army acquired 17,232 acres of private land in St. Charles County for the construction of the Weldon Spring Ordnance Works facility. The former Ordnance Works site has since been divided into several contiguous areas under different ownership, as depicted in Figure 2. Current land use of the former Ordnance Works site includes the former Chemical Plant and Quarry, the U.S. Army Reserve Weldon Spring Training Area, the Missouri Department of Conservation (MDC), the Missouri Department of Natural Resources (MDNR) Division of State Parks (MDNR-Parks), Francis Howell High School, a St. Charles County highway maintenance (formerly Missouri Department of Transportation [MoDOT]) facility, the Public Water Supply District No. 2 water supply facility, the St. Charles County law enforcement training center, the village of Weldon Spring Heights, and a University of Missouri research park. The former Chemical Plant and Quarry areas total 228.16 acres. The Former Chemical Plant property occupies 219.50 acres, and the Quarry occupies 8.66 acres.« less

3D P and S Wave Velocity Structure and Tremor Locations in the Parkfield Region

NASA Astrophysics Data System (ADS)

Zeng, X.; Thurber, C. H.; Shelly, D. R.; Bennington, N. L.; Cochran, E. S.; Harrington, R. M.

2014-12-01

We have assembled a new dataset to refine the 3D seismic velocity model in the Parkfield region. The S arrivals from 184 earthquakes recorded by the Parkfield Experiment to Record MIcroseismicity and Tremor array (PERMIT) during 2010-2011 were picked by a new S wave picker, which is based on machine learning. 74 blasts have been assigned to four quarries, whose locations were identified with Google Earth. About 1000 P and S wave arrivals from these blasts at permanent seismic network were also incorporated. Low frequency earthquakes (LFEs) occurring within non-volcanic tremor (NVT) are valuable for improving the precision of NVT location and the seismic velocity model at greater depths. Based on previous work (Shelley and Hardebeck, 2010), waveforms of hundreds of LFEs in same family were stacked to improve signal qualify. In a previous study (McClement et al., 2013), stacked traces of more than 30 LFE families at the Parkfileld Array Seismic Observatory (PASO) have been picked. We expanded our work to include LFEs recorded by the PERMIT array. The time-frequency Phase Weight Stacking (tf-PWS) method was introduced to improve the stack quality, as direct stacking does not produce clear S-wave arrivals on the PERMIT stations. This technique uses the coherence of the instantaneous phase among the stacked signals to enhance the signal-to-noise ratio (SNR) of the stack. We found that it is extremely effective for picking LFE arrivals (Thurber et al., 2014). More than 500 P and about 1000 S arrivals from 58 LFE families were picked at the PERMIT and PASO arrays. Since the depths of LFEs are much deeper than earthquakes, we are able to extend model resolution to lower crustal depths. Both P and S wave velocity structure have been obtained with the tomoDD method. The result suggests that there is a low velocity zone (LVZ) in the lower crust and the location of the LVZ is consistent with the high conductivity zone beneath the southern segment of the Rinconada fault that was revealed in the 3D magnetotelluric inversion of Tietze and Ritter(2013).

40 CFR 63.541 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Hazardous Air Pollutants from Secondary Lead Smelting § 63.541 Applicability. (a) The provisions of this subpart apply to the following affected sources at all secondary lead smelters: blast, reverberatory, rotary, and electric smelting furnaces; refining kettles; agglomerating furnaces; dryers; process...

40 CFR 63.541 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Hazardous Air Pollutants from Secondary Lead Smelting § 63.541 Applicability. (a) The provisions of this subpart apply to the following affected sources at all secondary lead smelters: blast, reverberatory, rotary, and electric smelting furnaces; refining kettles; agglomerating furnaces; dryers; process...

CO2 (dry ice) cleaning system

NASA Technical Reports Server (NTRS)

Barnett, Donald M.

1995-01-01

Tomco Equipment Company has participated in the dry ice (solid carbon dioxide, CO2) cleaning industry for over ten years as a pioneer in the manufacturer of high density, dry ice cleaning pellet production equipment. For over four years Tomco high density pelletizers have been available to the dry ice cleaning industry. Approximately one year ago Tomco introduced the DI-250, a new dry ice blast unit making Tomco a single source supplier for sublimable media, particle blast, cleaning systems. This new blast unit is an all pneumatic, single discharge hose device. It meters the insertion of 1/8 inch diameter (or smaller), high density, dry ice pellets into a high pressure, propellant gas stream. The dry ice and propellant streams are controlled and mixed from the blast cabinet. From there the mixture is transported to the nozzle where the pellets are accelerated to an appropriate blasting velocity. When directed to impact upon a target area, these dry ice pellets have sufficient energy to effectively remove most surface coatings through dry, abrasive contact. The meta-stable, dry ice pellets used for CO2 cleaning, while labeled 'high density,' are less dense than alternate, abrasive, particle blast media. In addition, after contacting the target surface, they return to their equilibrium condition: a superheated gas state. Most currently used grit blasting media are silicon dioxide based, which possess a sharp tetrahedral molecular structure. Silicon dioxide crystal structures will always produce smaller sharp-edged replicas of the original crystal upon fracture. Larger, softer dry ice pellets do not share the same sharp-edged crystalline structures as their non-sublimable counterparts when broken. In fact, upon contact with the target surface, dry ice pellets will plastically deform and break apart. As such, dry ice cleaning is less harmful to sensitive substrates, workers and the environment than chemical or abrasive cleaning systems. Dry ice cleaning system components include: a dry ice pellet supply, a non-reactive propellant gas source, a pellet and propellant metering device, and a media transport and acceleration hose and nozzle arrangement. Dry ice cleaning system operating parameters include: choice of propellant gas, its pressure and temperature, dry ice mass flow rate, dry ice pellet size and shape, and acceleration nozzle configuration. These parameters may be modified to fit different applications. The growth of the dry ice cleaning industry will depend upon timely data acquisition of the effects that independent changes in these parameters have on cleaning rates, with respect to different surface coating and substrate combinations. With this data, optimization of cleaning rates for particular applications will be possible. The analysis of the applicable range of modulation of these parameters, within system component mechanical constraints, has just begun.

Handling of quarry waste from schist production at Oppdal, Norway

NASA Astrophysics Data System (ADS)

Willy Danielsen, Svein; Alnæs, Lisbeth; Azrague, Kamal; Suleng, Jon

2017-04-01

Handling of quarry waste from schist production at Oppdal, Norway Svein Willy Danielsen1), Lisbeth Alnæs2), Kamal Azrague2), Jon Suleng3) 1) Geomaterials Consultant, Trondheim Norway, 2) SINTEF, Trondheim, Norway, 3) AF Gruppen AS, Oppdal, Norway A significant amount of aggregate research in Norway has been focused on the recovery and use of surplus sizes from hard rock aggregate quarries. The use of sand sized quarry waste (QW) from crushing/processing has been motivated by the rapid depletion of traditional sand/gravel resources, increasing land-use conflicts, and the need to minimise QW deposits which for some quarries are becoming a critical factor for economy as well as for environmental reasons. With an annual aggregate production of 77 million tons, out of which approximately 83 % comes from hard rock, the annual volume of size < 4 mm will be of the order of 19 million tons. Converting this into construction aggregates is a major challenge in order to obtain satisfactory mass balance. This challenge is even bigger for quarries producing decorative stones. E.g. the quarrying and production of schist products for building purpose normally utilises as little as 10-15 % of the excavated rock. Oppdal in central Norway is a main supplier of schist products for flooring, roofing and decorative purpose. The high percentage of QW is due to strict requirements to the finished products, both regarding processing and the character of the parent rock. The need to deposit large amounts of QW is a serious setback for the quarry economy. Within a limited time horizon the volumes of QW can threaten the further exploitation by merely choking the quarry. On the opposite side - any process that can convert the QW into sellable products will give a tremendous added value for the producer. Besides, the area in question is about to drain out its available aggregate resources, having to rely on long-transported sand and gravel. This has consequences not only for the economy, but also for the environment since heavy lorry transport will not be sustainable. An on-going project is now looking into converting the QW into quality aggregate both for road construction and concrete. Novel crusher technology and processing strategy is being applied and adapted, and the finished products will be tested in laboratories to establish the relevant application parameters and obtainable quality. By producing coarse aggregates for primarily road purpose, it is estimated that the QW can be reduced from todaýs approx. 90 % to approx. 40 %. The potential by also installing the latest inventions of crusher technology designed for making manufactured sand, is to further reduce QW down to < 10 %. Making all these materials sellable in the market, the economic - and also environmental - potential will be considerable. Understanding the geological conditions and petrographic properties of the rock is vital. This is a quartz-feldspar rich metamorphic rock - a meta-arkose - containing rhythmically distributed planar lamina (less than 2 mm thick) or scattered occurrence of mica, separated by layers composed predominately of quartz and feldspar. The rock can be split along the lamina to slabs varying from 0.5 cm to more than 10 cm in thickness, and the microstructure can be characterized as being granoblastic to gneissic. . This makes it possible by well designed crushing process and careful selection of the in-going rock particles, to obtain well shaped aggregates up to at least 20 mm. The on-going project will also study the total cost situation depending on the QW utilisation, discuss the environmental and sustainability issues with a societal perspective, and also consider the market opportunities.

Gamma radiation effects on the dynamic fatigue measurements of glass discs

NASA Technical Reports Server (NTRS)

Ananaba, T. O. J.; Kinser, D. L.

1985-01-01

Circular specimens of low iron soda lime silicate glass were blasted with grit after having a circular notch etched into their centers. After separation into two groups, one group was exposed to gamma radiation. The fracture strengths of all samples were then tested by the biaxial technique, i.e., specimens were balanced on three balls and loaded in the center by a piston. The irradiated samples had received a 140,000 Gy dose from a Co-60 source. An enhanced interaction between the ambient moisture and the grit-blasted central notch was observed in the irradiated samples, which displayed accelerated corrosion.

A cosmic-ray-mediated shock in the solar system

NASA Technical Reports Server (NTRS)

Eichler, D.

1981-01-01

It is pointed out that the flare-induced blast wave of Aug. 4, 1972, the most violent disturbance in the solar wind on record, produced cosmic rays with an efficiency of about 50%. Such a high efficiency is predicted by the self-regulating production model of cosmic-ray origin in shocks. Most interplanetary shocks, according to simple theoretical analysis, are not strong enough to produce cosmic rays efficiently. However, if shock strength is the key parameter governing efficiency, as present interplanetary data suggest, then shocks from supernova blasts, quasar outbursts, and other violent astrophysical phenomena should be extremely efficient sources of cosmic rays.

Simulation and Measurements of Small Arms Blast Wave Overpressure in the Process of Designing a Silencer

NASA Astrophysics Data System (ADS)

Hristov, Nebojša; Kari, Aleksandar; Jerković, Damir; Savić, Slobodan; Sirovatka, Radoslav

2015-02-01

Simulation and measurements of muzzle blast overpressure and its physical manifestations are studied in this paper. The use of a silencer can have a great influence on the overpressure intensity. A silencer is regarded as an acoustic transducer and a waveguide. Wave equations for an acoustic dotted source of directed effect are used for physical interpretation of overpressure as an acoustic phenomenon. Decomposition approach has proven to be suitable to describe the formation of the output wave of the wave transducer. Electroacoustic analogies are used for simulations. A measurement chain was used to compare the simulation results with the experimental ones.

Nivelstein sandstone, weakly lithified pure silica sands from the Dutch-German border area, intermittently used in architecture for two millennia

NASA Astrophysics Data System (ADS)

Nijland, Timo G.; Wim Dubelaar, C.

2017-04-01

The current paper provides a concise overview of the geological setting of the Nivelstein sandstone in broad sense, its petrographic and physical characteristics, and its use as natural stone. Miocene pure silica sands occur around Heerlen in the southeastern part of the Dutch province of Limburg and Herzogenrath in adjacent Germany, as well as in the Belgian province of Limburg near Opgrimbie. In Dutch Limburg and in Germany are three large active exploitations, quarrying the sands for industrial purposes. On top of the unconsolidated sands in the Herzogenrath quarry, lithified banks of sandstone occur, known as Nivelstein (or more rarely Herzogenrath) sandstone. This sandstone has been used as dimension stone and ornamental stone since Roman times. In the 11th century the quarry was reopened and after a long period of disuse sandstone blocks were again quarried in the second half of the 19th century. The lithification of the Nivelstein sandstone usually is very weak, with grain to grain contacts and some newly formed quartz rims only. The clay content is extremely low and is restricted to tiny booklets of kaolinite. Despite the weak cementation the Nivelstein sandstone has proved to be very time-resistant building stone that forms a major element in the stone cultural heritage of the Dutch- German border area.

Optical shaping of gas targets for laser–plasma ion sources

DOE PAGES

Dover, N. P.; Cook, N.; Tresca, O.; ...

2016-02-09

In this paper, we report on the experimental demonstration of a technique to generate steep density gradients in gas-jet targets of interest to laser–plasma ion acceleration. By using an intentional low-energy prepulse, we generated a hydrodynamic blast wave in the gas to shape the target prior to the arrival of an intense COmore » $$_{2}$$($${\\it\\lambda}\\approx 10~{\\rm\\mu}\\text{m}$$) drive pulse. This technique has been recently shown to facilitate the generation of ion beams by shockwave acceleration (Trescaet al.,Phys. Rev. Lett., vol. 115 (9), 2015, 094802). Here, we discuss and introduce a model to understand the generation of these blast waves and discuss in depth the experimental realisation of the technique, supported by hydrodynamics simulations. With appropriate prepulse energy and timing, this blast wave can generate steepened density gradients as short as$$l\\approx 20~{\\rm\\mu}\\text{m}$$($1/e$), opening up new possibilities for laser–plasma studies with near-critical gaseous targets.« less

Simulating the Initial Dynamics of the 18 May 1980 Mount St.Helens Blast

NASA Astrophysics Data System (ADS)

Esposti Ongaro, T.; Widiwijayanti, C.; Voight, B.; Clarke, A. B.; Neri, A.

2008-12-01

The initial stage of the 18 May 1980 blast at Mount St. Helens (MSH) has been simulated numerically by the 2D/3D multiphase multiparticle flow model PDAC (Neri et al., J. Geophys. Res. 108 (B4), 2003; Esposti Ongaro et al., Parallel Computing 33, 2007), to provide further insight into the fluid dynamics of this phenomenon. Initial source conditions, including the gas content, the total mass of juvenile and entrained rocks, the temperature, grain size distribution and pre-eruption pressure distribution in the lava dome have been parameterized accordingly to field evidence, available geological constraints and simple theoretical models. Simulation results suggest that the MSH blast can be characterized as an expansion phase (burst), lasting about ten seconds, followed by collapse and pyroclastic density current (PDC) phases. In the burst phase the pressure forces dominate and the flow can locally reach supersonic velocities and generate pressure waves that can be tracked by the numerical model. In the collapse and PDC phases the flow is dominantly gravity-driven and the dynamics are strongly controlled by the source geometry, vertical stratification within the flow and by the 3D topography. The simulations suggest that the severe damage observed at MSH can be explained by high dynamic pressures in gravity currents, and the rapid decrease of dynamic pressure from proximal to distal areas (and related parameters of PDC velocity and density) was largely related to rugged topography beyond the North Fork Toutle River valley. Although the source models investigated thus far represent a simplification of the actual geometry and complex sequence of initial events, we show that the explosion mechanisms are significantly robust over a wide range of initial conditions. Simulation results for MSH are also consistent with those obtained in a previous application of a similar model to the 1997 Boxing Day blast pulses at Soufriere Hills volcano (Montserrat, West Indies) (Esposti Ongaro et al., J. Geophys. Res. 113 (B03211), 2008), which were at least ten times smaller, thus suggesting that the simulated mechanisms are largely independent of eruption scale.

Field Trial of Distributed Acoustic Sensing in an Active Room-and-Pillar Mine

NASA Astrophysics Data System (ADS)

Wang, H. F.; Zeng, X.; Lord, N. E.; Fratta, D.; Coleman, T.; Maclaughlin, M.

2017-12-01

A Distributed Acoustic Sensing (DAS) field trial was conducted in July 2017 on the floor of the first level of the Lafarge-Conco limestone mine in N. Aurora Illinois. The room-and-pillar mine occupies a wedge-shaped footprint that is approximately 1500 m long by 500 m wide at the midpoint. The mine consists of four levels down to a depth of about 80 m. Pillars are approximately 20-meters on a side and in height. DAS cable was deployed in a shallow groove cut with a pavement saw. The groove was approximately 300-meters long and in the overall shape of an irregular rectangle as it followed a pathway around three pillars in each direction. The groove was 1.25-cm wide and between 2.5 and 7.5-cm deep. Three strands of fiber-optic cable were placed in the groove, positioned one above the other and separated by different materials. The bottom cable was covered with cement to a depth of 1.25-cm and allowed to dry for several days. The middle strand was covered with fines and the top strand was without cover. The DAS array consisted of the three co-located strands connected in series. It recorded signals from daily mine blasts on the afternoons of July 27 and 28. The blast locations were along the mine perimeter at a distance of about 1 km from the array. In addition to the distant blast source, a series of near-array tests were made with a weight-drop source located at surveyed points along the cable and within the array. Average mine-scale velocities were obtained from travel times from blast locations to different DAS channels. Local seismic velocities were obtained from first arrivals of the weight-drop source and from moveout of traces with time. The DAS response and travel times were noted as a function of cable direction. The field test showed that DAS can be used to monitor ground motion within an active mine. The research project is funded by a contract to Montana Tech from the National Institute for Occupational Safety and Health, Office of Mine Safety and Health Research.

Localization of small arms fire using acoustic measurements of muzzle blast and/or ballistic shock wave arrivals.

PubMed

Lo, Kam W; Ferguson, Brian G

2012-11-01

The accurate localization of small arms fire using fixed acoustic sensors is considered. First, the conventional wavefront-curvature passive ranging method, which requires only differential time-of-arrival (DTOA) measurements of the muzzle blast wave to estimate the source position, is modified to account for sensor positions that are not strictly collinear (bowed array). Second, an existing single-sensor-node ballistic model-based localization method, which requires both DTOA and differential angle-of-arrival (DAOA) measurements of the muzzle blast wave and ballistic shock wave, is improved by replacing the basic external ballistics model (which describes the bullet's deceleration along its trajectory) with a more rigorous model and replacing the look-up table ranging procedure with a nonlinear (or polynomial) equation-based ranging procedure. Third, a new multiple-sensor-node ballistic model-based localization method, which requires only DTOA measurements of the ballistic shock wave to localize the point of fire, is formulated. The first method is applicable to situations when only the muzzle blast wave is received, whereas the third method applies when only the ballistic shock wave is received. The effectiveness of each of these methods is verified using an extensive set of real data recorded during a 7 day field experiment.

A geophysical shock and air blast simulator at the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fournier, K. B.; Brown, C. G.; May, M. J.

2014-09-15

The energy partitioning energy coupling experiments at the National Ignition Facility (NIF) have been designed to measure simultaneously the coupling of energy from a laser-driven target into both ground shock and air blast overpressure to nearby media. The source target for the experiment is positioned at a known height above the ground-surface simulant and is heated by four beams from the NIF. The resulting target energy density and specific energy are equal to those of a low-yield nuclear device. The ground-shock stress waves and atmospheric overpressure waveforms that result in our test system are hydrodynamically scaled analogs of full-scale seismicmore » and air blast phenomena. This report summarizes the development of the platform, the simulations, and calculations that underpin the physics measurements that are being made, and finally the data that were measured. Agreement between the data and simulation of the order of a factor of two to three is seen for air blast quantities such as peak overpressure. Historical underground test data for seismic phenomena measured sensor displacements; we measure the stresses generated in our ground-surrogate medium. We find factors-of-a-few agreement between our measured peak stresses and predictions with modern geophysical computer codes.« less

A geophysical shock and air blast simulator at the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fournier, K. B.; Brown, C. G.; May, M. J.

2014-09-01

The energy partitioning energy coupling experiments at the National Ignition Facility (NIF) have been designed to measure simultaneously the coupling of energy from a laser-driven target into both ground shock and air blast overpressure to nearby media. The source target for the experiment is positioned at a known height above the ground-surface simulant and is heated by four beams from the NIF. The resulting target energy density and specific energy are equal to those of a low-yield nuclear device. The ground-shock stress waves and atmospheric overpressure waveforms that result in our test system are hydrodynamically scaled analogs of full-scale seismicmore » and air blast phenomena. This report summarizes the development of the platform, the simulations, and calculations that underpin the physics measurements that are being made, and finally the data that were measured. Agreement between the data and simulation of the order of a factor of two to three is seen for air blast quantities such as peak overpressure. Historical underground test data for seismic phenomena measured sensor displacements; we measure the stresses generated in our ground-surrogate medium. We find factors-of-a-few agreement between our measured peak stresses and predictions with modern geophysical computer codes.« less

Blast and Fragment Protective Sandwich Panel Concepts for Stainless Steel Monohull Designs

DTIC Science & Technology

2008-10-21

to draw broader conclusions. 8. Concluding remarks The resistance of metallic sandwich panels to localized spherical impulsive sources has been...hour per response, including the time for reviewing instructions, searching existing data sources , gathering and maintaining the data needed, and...applications and ship hull blister attachments. Technical Approach The approach used in this research program exploited progress made in metallic

Experimental evolution reveals genome-wide spectrum and dynamics of mutations in the rice blast fungus, Magnaporthe oryzae.

PubMed

Jeon, Junhyun; Choi, Jaeyoung; Lee, Gir-Won; Dean, Ralph A; Lee, Yong-Hwan

2013-01-01

Knowledge on mutation processes is central to interpreting genetic analysis data as well as understanding the underlying nature of almost all evolutionary phenomena. However, studies on genome-wide mutational spectrum and dynamics in fungal pathogens are scarce, hindering our understanding of their evolution and biology. Here, we explored changes in the phenotypes and genome sequences of the rice blast fungus Magnaporthe oryzae during the forced in vitro evolution by weekly transfer of cultures on artificial media. Through combination of experimental evolution with high throughput sequencing technology, we found that mutations accumulate rapidly prior to visible phenotypic changes and that both genetic drift and selection seem to contribute to shaping mutational landscape, suggesting the buffering capacity of fungal genome against mutations. Inference of mutational effects on phenotypes through the use of T-DNA insertion mutants suggested that at least some of the DNA sequence mutations are likely associated with the observed phenotypic changes. Furthermore, our data suggest oxidative damages and UV as major sources of mutation during subcultures. Taken together, our work revealed important properties of original source of variation in the genome of the rice blast fungus. We believe that these results provide not only insights into stability of pathogenicity and genome evolution in plant pathogenic fungi but also a model in which evolution of fungal pathogens in natura can be comparatively investigated.

Empirical Calibration of Small Explosion Seismic And Acoustic Phenomenology in New England

DTIC Science & Technology

2008-10-31

site was too close to a nearby cell /radio tower and the active quarry wall to detonate our planned 400 lb explosions. Core drilling at an...alternative test site (Figure 52) was conducted further away from the active quarry wall and a nearby cell /radio tower. The alternative site would be far...experiment was returned into the original location (Figure 52). In order to reduce the projected ground vibrations at the cell /radio tower and high

The Experience of Implementation of Innovative Technology of Quarry Waste Water Purifying in Kuzbass Open Pit

NASA Astrophysics Data System (ADS)

Lesin, Yu V.; Hellmer, M. C.

2016-08-01

Among all industries in Kuzbass (Western Siberia, Russia) the coal industry provides the most environmental threat. However, the construction of new and maintenance of existing open pit mines do not often correspond to the tasks of improving the environmental safety of surface mining. So the article describes the use of innovative quarry waste water purifying technology implemented in Kuzbass open pit mine «Shestaki». This technology is based on using artificial filter arrays made of overburden rock.

Quantification of Rock Damage from Small Explosions and Its Effect on Shear-Wave Generation

DTIC Science & Technology

2009-06-15

close to a nearby cell /radio tower and the active quarry wall to detonate our planned 400 lb explosions. Core drilling at an alternative test site...Figure ) was conducted further away from the active quarry wall and a nearby cell /radio tower. The alternative site would be far enough away from...returned into the original location (Figure ). In order to reduce the projected ground vibrations at the cell /radio tower and high wall of the active

Characterization of PM 2.5 fugitive metal in the workplaces and the surrounding environment of a secondary aluminum smelter

NASA Astrophysics Data System (ADS)

Kuo, Su-Ching; Hsieh, Li-Ying; Tsai, Cheng-Hsien; Tsai, Ying I.

Fugitive metal in PM 2.5 at the blast furnace ( S1), reverberatory furnace ( S2), and surrounding environment ( S0) of a secondary aluminum smelter (a secondary ALS) was studied. PM 2.5 mass concentration at the blast furnace exceeded that at the reverberatory furnace and this was especially apparent during operation, giving an early indication that the blast furnace is more important as a pollutant source. Further, PM 2.5 mass concentration levels and patterns at S0 indicated that emissions from the blast furnace and reverberatory furnace were the major source of the observed fine particle pollution in the surrounding environment. Si and K were the main components and hence pollutants by mass in the PM 2.5 at S1, S2 and S0 during both operation and non-operation. Hg was not detected in the PM 2.5 aerosol during smelter operation but was present at all three sampling locations during non-operation. This is due to the falling blast furnace and reverberatory furnace temperatures during non-operation which cause Hg vapor formed during operation to condense to form detectable Hg particles, and hence Hg contributes to the pollutant load during non-operation. Average S1/ S0 and S2/ S0 mass concentration ratios of 40.32 and 18.53, respectively, for all measured metals during operation and 7.83 and 5.73 for all measured metals during non-operation indicate that metal particulate pollution at the workplaces of secondary ALSs, particularly at the blast furnace during operation, is a serious issue. S1/ S0 mass concentration ratios were higher still for Pb (62.22), Ti (113.40) and Ba (248.64), while the S2/ S0 mass concentration ratio for Mo was 138.20. Principal component analyses produced a PC1 that explained 32.36-48.16% of the total variance during operation of the smelter and 47.86-69.Ten percent during non-operation. Their strong component loadings were mainly related to the fugitive PM 2.5 mass. Compared to atmospheric metal concentrations reported for other regions of the world, the toxic metals that have relatively higher concentrations in the secondary ALS emissions are Cr, Cd, Cu, As, Pb, Se, Al and Zn, especially during smelter operation. Concentrations of these toxic heavy metals are approximately 2-4 orders of magnitude higher than those reported for various industrial regions and metropolises with heavy traffic across the world.

NOA at the Calaveras Dam Replacement Project (CDRP) - Challenges and Solutions

NASA Astrophysics Data System (ADS)

Erskine, B.

2012-12-01

The San Francisco Public Utilities Commission is one year into construction of the Calaveras Dam Replacement Project (CDRP), a new earthen dam east of Sunol designed to withstand an M 7.1 earthquake on the nearby active Calaveras fault. The zoned earthen dam will be constructed primarily of on-site materials, many of which contain NOA. The upstream shell will be composed of Franciscan complex blueschist which contains crocidolite. This material will be blasted and processed at an on-site quarry. The impermeable core of the dam will be constructed of clay-rich alluvium that contains asbestos derived from Franciscan rocks. This material will be excavated from the south end of the reservoir and transported several miles to the dam. Currently, approximately 3 million yards of Franciscan complex material is being excavated and disposed of within permitted on-site engineered landfills. NOA-bearing rocks that include serpentinite, greenschist, blueschist, and eclogite contain variable amounts and assemblages of chrysotile, actinolite, crocidolite, tremolite, and winchite-class amphiboles. All of these are detected in air samples collected within a sophisticated air monitoring array and analyzed by TEM. The CDRP represents the largest construction project involving NOA in the country. As such, applying regulations that were designed for building materials and routine construction sites, and controlling airborne emissions on such a massive scale, is a major challenge requiring innovative solutions. Because construction occurs simultaneously at distinct and distant parts of the site, and the rugged topography of the site induces complex meteorological conditions, it is sometimes difficult to ascertain the driving activity and location of a source that caused a trigger level exceedance at a perimeter monitoring station. One helpful tool is forensic correlation of source material and air test data using speciation of amphiboles. At the CDRP, we are developing the ability to correlate rock mineralogy at a location with the species of amphiboles identified on air samples using TEM. Using amphibole species as a fingerprinting tool, we have been successful in determining whether an exceedance of a trigger level was caused from onsite or offsite sources. In one case, multiple exceedances by an unusual mix of chrysotile and amphiboles (crocidolite, actinolite, tremolite, and Libby-class amphiboles in the same sample) narrowed the source to one of two locations: Disposal Site 3 where a mix of materials from the entire site is disposed of, and water recycled in the decontamination zone wheel wash equipment. Using perimeter air monitoring around and between each location it was possible to identify the wheel wash as the source. As a result, the wheel wash system, track out procedures, and road wetting protocol have been re-engineered to eliminate the potential for significant offsite emissions. These and other examples will describe how the SFPUC NOA team is managing the field determination of NOA, on-site control measures, and perimeter air monitoring to assure that construction is conducted in a safe manner and no offsite exposures to the public occur.

40 CFR 60.180 - Applicability and designation of affected facility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Primary Lead Smelters § 60.180 Applicability and designation of affected facility. (a) The...: sintering machine, sintering machine discharge end, blast furnace, dross reverberatory furnace, electric...

40 CFR 60.180 - Applicability and designation of affected facility.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Primary Lead Smelters § 60.180 Applicability and designation of affected facility. (a) The...: sintering machine, sintering machine discharge end, blast furnace, dross reverberatory furnace, electric...

Exploring old caves

NASA Astrophysics Data System (ADS)

Luana Belli, Maria

2015-04-01

Quarries, caves and mines often contain fossils. During the '30s in Rome, the urban expansion needs for building materials such as gravel, sand and clay were extracted from quarries that surrounded the city. One of these quarries in particular, in the area of Saccopastore (Nomentana area 3 km from the University Sapienza Roma) returned an ancient human fossil skull belonging to a Neanderthal (most likely a female) who lived in Latium about 120,000 years ago. Detailed studies of this fossil were carried out by Sergio Sergi, the son of the founder of the Museum of Anthropology in Rome, Giuseppe Sergi. The museum was founded in 1884 and was later transferred to the University City (1934) where it is still located. Professor Maria Luana Belli, a science teacher in the Liceo Scientifico "G. Keplero" is a volunteer and collaborator with the Museum "G. Sergi", and she and her students retrace the places of the discovery on the trail of the Neanderthals, for understanding the evolution of the territory in a perspective of interdisciplinary teaching.

Laser removal of graffiti from Pink Morelia Quarry

NASA Astrophysics Data System (ADS)

Penide, J.; Quintero, F.; Riveiro, A.; Sánchez-Castillo, A.; Comesaña, R.; del Val, J.; Lusquiños, F.; Pou, J.

2013-11-01

Morelia is an important city sited in Mexico. Its historical center reflects most of their culture and history, especially of the colonial period; in fact, it was appointed World Heritage Site by UNESCO. Sadly, there is a serious problem with graffiti in Morelia and its historical center is the worst affected since its delicate charming is definitely damaged. Hitherto, the conventional methods employed to remove graffiti from Pink Morelia Quarry (the most used building stone in Morelia) are quite aggressive to the appearance of the monuments, so actually, they are not a very good solution. In this work, we performed a study on the removal of graffiti from Pink Morelia Quarry by high power diode laser. We carried out an extensive experimental study looking for the optimal processing parameters, and compared a single-pass with a multi-pass method. Indeed, we achieved an effective cleaning without producing serious side effects in the stone. In conclusion, the multi-pass method emitting in continuous wave was revealed as the more effective operating modes to remove the graffiti.

High Cigarette and Poly-Tobacco Use Among Workers in a Dusty Industry: New Jersey Quarry Workers.

PubMed

Graber, Judith M; Worthington, Karen; Almberg, Kirsten S; Meng, Qingyu; Rose, Cecile S; Cohen, Robert A

2016-04-01

Tobacco use is high among US extraction and construction workers, who can also incur occupational dust exposure. Information on different types of tobacco use among quarry/mine workers is sparse. During mandated training sessions, New Jersey quarry workers were surveyed about their tobacco use. Prevalence was calculated for single and multiple tobacco use by demographic and workplace characteristics; logistic regression was used to assess associations with smoking. Two hundred forty (97.1%) workers completed surveys. Among respondents, 41.7% [95% confidence interval (95% CI) 35.4 to 48.3] currently used any tobacco product of whom 28.1% smoked cigarettes. In multivariate analysis, positive associations with smoking included working as a contractor versus mine employee (odds ratio 2.32, 95% CI 1.01 to 5.36) and a usual job title of maintenance (odds ratio 2.02, 95% CI 0.87 to 4.94). Industry-specific information may be helpful in developing targeted tobacco-cessation programs.

Developing biodiversity indicators on a stakeholders' opinions basis: the gypsum industry Key Performance Indicators framework.

PubMed

Pitz, Carline; Mahy, Grégory; Vermeulen, Cédric; Marlet, Christine; Séleck, Maxime

2016-07-01

This study aims to establish a common Key Performance Indicators (KPIs) framework for reporting about the gypsum industry biodiversity at the European level. In order to integrate different opinions and to reach a consensus framework, an original participatory process approach has been developed among different stakeholder groups: Eurogypsum, European and regional authorities, university scientists, consulting offices, European and regional associations for the conservation of nature, and the extractive industry. The strategy is developed around four main steps: (1) building of a maximum set of indicators to be submitted to stakeholders based on the literature (Focus Group method); (2) evaluating the consensus about indicators through a policy Delphi survey aiming at the prioritization of indicator classes using the Analytic Hierarchy Process method (AHP) and of individual indicators; (3) testing acceptability and feasibility through analysis of Environmental Impact Assessments (EIAs) and visits to three European quarries; (4) Eurogypsum final decision and communication. The resulting framework contains a set of 11 indicators considered the most suitable for all the stakeholders. Our KPIs respond to European legislation and strategies for biodiversity. The framework aims at improving sustainability in quarries and at helping to manage biodiversity as well as to allow the creation of coherent reporting systems. The final goal is to allow for the definition of the actual biodiversity status of gypsum quarries and allow for enhancing it. The framework is adaptable to the local context of each gypsum quarry.

Quarry identification of historical building materials by means of laser induced breakdown spectroscopy, X-ray fluorescence and chemometric analysis

NASA Astrophysics Data System (ADS)

Colao, F.; Fantoni, R.; Ortiz, P.; Vazquez, M. A.; Martin, J. M.; Ortiz, R.; Idris, N.

2010-08-01

To characterize historical building materials according to the geographic origin of the quarries from which they have been mined, the relative content of major and trace elements were determined by means of Laser Induced Breakdown Spectroscopy (LIBS) and X-ray Fluorescence (XRF) techniques. 48 different specimens were studied and the entire samples' set was divided in two different groups: the first, used as reference set, was composed by samples mined from eight different quarries located in Seville province; the second group was composed by specimens of unknown provenance collected in several historical buildings and churches in the city of Seville. Data reduction and analysis on laser induced breakdown spectroscopy and X-ray fluorescence measurements was performed using multivariate statistical approach, namely the Linear Discriminant Analysis (LDA), Principal Component Analysis (PCA) and Soft Independent Modeling of Class Analogy (SIMCA). A clear separation among reference sample materials mined from different quarries was observed in Principal Components (PC) score plots, then a supervised soft independent modeling of class analogy classification was trained and run, aiming to assess the provenance of unknown samples according to their elemental content. The obtained results were compared with the provenance assignments made on the basis of petrographical description. This work gives experimental evidence that laser induced breakdown spectroscopy measurements on a relatively small set of elements is a fast and effective method for the purpose of origin identification.

Chemical characterization of atmospheric particles and source apportionment in the vicinity of a steelmaking industry.

PubMed

Almeida, S M; Lage, J; Fernández, B; Garcia, S; Reis, M A; Chaves, P C

2015-07-15

The objective of this work was to provide a chemical characterization of atmospheric particles collected in the vicinity of a steelmaking industry and to identify the sources that affect PM10 levels. A total of 94 PM samples were collected in two sampling campaigns that occurred in February and June/July of 2011. PM2.5 and PM2.5-10 were analyzed for a total of 22 elements by Instrumental Neutron Activation Analysis and Particle Induced X-ray Emission. The concentrations of water soluble ions in PM10 were measured by Ion Chromatography and Indophenol-Blue Spectrophotometry. Positive Matrix Factorization receptor model was used to identify sources of particulate matter and to determine their mass contribution to PM10. Seven main groups of sources were identified: marine aerosol identified by Na and Cl (22%), steelmaking and sinter plant represented by As, Cr, Cu, Fe, Ni, Mn, Pb, Sb and Zn (11%), sinter plant stack identified by NH4(+), K and Pb (12%), an unidentified Br source (1.8%), secondary aerosol from coke making and blast furnace (19%), fugitive emissions from the handling of raw material, sinter plant and vehicles dust resuspension identified by Al, Ca, La, Si, Ti and V (14%) and sinter plant and blast furnace associated essentially with Fe and Mn (21%). Copyright © 2015 Elsevier B.V. All rights reserved.

Laser Scanning for the definition of high resolution topography in the Apuan Alps (IT) marble district

NASA Astrophysics Data System (ADS)

Riccucci, Silvia; Salvini, Riccardo; Francioni, Mirko

2010-05-01

The present paper describes the results of five laser scanning surveys performed by a Leica™ ScanStation2 with the aim of producing an high definition topography of a quarry, at the scale of 1:1,000. The project comes from a joint research carried out by the Authors in collaboration with the Local Sanitary Unit Agency (ASL n.1) of Massa and Carrara (IT). The main objective of this work has been the survey of both the exploited quarry walls and the upper residual and natural slopes. The area of interest is characterized by several quarry fronts which develop to variable and alternate directions to create very evident rock spurs, from NW-SE to NE-SW trending for a total wideness of about 2 hectares. Moreover, the quarry walls are sub-vertical and sometimes overhang by a total height of 100 m in respect to the quarry floor. Differential GPS and orthometric correction have been applied in order to co-register and to georeference the five point clouds; for these purposes a series of optical targets have been measured using a Laser Total Station. The subsequent phase has been the mesh construction and editing, from which a topographic map, 25 cm equidistance contours lines, has been created. The planimetric map shows the position and the geometry of crests, banks, escarpments, walls and all others exploitation features and the characteristics of the upper natural slopes. Morphological profiles along the maximum slope have been realized in order to better plan the future extractive activities according to the regional law. In order to make easier the prospective observation of detailed and overall areas, 3D views of multi-directional orientation have been realized. The produced data has been published by using the free LeicaTM TruView plug-in for Internet Explorer in a way to easily view the photographs and to measure the laser scan point clouds. Processing results have highlighted the higher spatial resolution of data coming from laser scanning in respect to the traditional topographic methodologies. Such information can be used for multitemporal evaluation of mining volumes. For local authorities the control of extraction volumes can be more easily and rapidly executed by map algebra function of image differencing between bi-temporal Digital Dense Surface Model (DDSM) of the quarry walls. Finally, the DDSM has been utilized by the Authors to analyze the rock slope stability, to collect geological-engineering data, such as joints attitude and spacing, and to perform detailed analysis of rockfall trajectories.

Numerical analysis of instability processes in underground cavities and of the related effects at the surface

NASA Astrophysics Data System (ADS)

Lollino, Piernicola; Parise, Mario

2010-05-01

Natural and anthropogenic caves may represent a potential hazard for the built-up environment, due to the occurrence of underground instability processes, that may propagate upward and eventually reach the ground surface, thus inducing the occurrence of sinkholes. Especially when the caves are at shallow depth, the effects at the ground surface may result extremely severe. In the Apulia region of southern Italy, there are many sites where underground quarrying developed in the past, due to presence at a certain depth of rock of good quality for building purposes. Development of underground quarries, rather than open pit mines, was also favoured by the preservation of the terrains on the ground surface for agricultural practices. The Pliocene-Pleistocene calcarenite (a typical soft rock) was therefore quarried underground, by digging extensive networks of galleries in those levels within the local geological succession most suitable for the quarrying activity. With time, these underground activities have progressively been abandoned, and later on many quarries were used for other purposes, including illegal discharge of solid and liquid wastes. Many Apulian towns are nowadays located just above these caves, due to urban expansion in the last decades and loss of memory of the presence of the underground quarries. Thus, a serious risk exists for civil society, which should not be left uninvestigated. The present contribution deals with the analysis of the main factors at the origin of the instability processes described, also including those causing weathering of the soft rock wihich induces gradual decay of the physical and mechanical properties of the rock mass. Aimed at exploring the evolution with time of the stability conditions within the cavities, numerical analysis have been implemented by using finite element methods with respect to ideal situations which are representative of typical case studies in Apulia. Both the effects of local instability processes occurring within the underground case and the effects of the progressive enlargement of the caves have been explored. Sensitivity analyses have been carried out to evaluate the influence of the rock properties on the cave stability. Moreover, decay processes of the mechanical properties of the rock mass as a consequence of wetting and weathering phenomena in the areas surrounding the caves have been simulated. The results achieved from the numerical analyses have been then compared to what has been observed in situ during several field surveys and a satisfactory agreement between the numerical simulations and the instability processes detected in the field has been noticed.

Combination of photogrammetric and geoelectric methods to assess 3d structures associated to natural hazards

NASA Astrophysics Data System (ADS)

Fargier, Yannick; Dore, Ludovic; Antoine, Raphael; Palma Lopes, Sérgio; Fauchard, Cyrille

2016-04-01

The extraction of subsurface materials is a key element for the economy of a nation. However, natural degradation of underground quarries is a major issue from an economic and public safety point of view. Consequently, the quarries stakeholders require relevant tools to define hazards associated to these structures. Safety assessment methods of underground quarries are recent and mainly based on rock physical properties. This kind of method leads to a certain homogeneity assumption of pillar internal properties that can cause an underestimation of the risk. Electrical Resistivity Imaging (ERI) is a widely used method that possesses two advantages to overcome this limitation. The first is to provide a qualitative understanding for the detection and monitoring of anomalies in the pillar body (e.g. faults). The second is to provide a quantitative description of the electrical resistivity distribution inside the pillar. This quantitative description can be interpreted with constitutive laws to help decision support (water content decreases the mechanical resistance of a chalk). However, conventional 2D and 3D Imaging techniques are usually applied to flat surface surveys or to surfaces with moderate topography. A 3D inversion of more complex media (case of the pillar) requires a full consideration of the geometry that was never taken into account before. The Photogrammetric technique presents a cost effective solution to obtain an accurate description of the external geometry of a complex media. However, this method has never been fully coupled with a geophysical method to enhance/improve the inversion process. Consequently we developed a complete procedure showing that photogrammetric and ERI tools can be efficiently combined to assess a complex 3D structure. This procedure includes in a first part a photogrammetric survey, a processing stage with an open source software and a post-processing stage finalizing a 3D surface model. The second part necessitates the production of a complete 3D mesh of the previous surface model to operate some forward modelization of the geo-electrical problem. To solve the inverse problem and obtain a 3D resistivity distribution we use a double grid method associated with a regularized Gauss-Newton inversion scheme. We applied this procedure to a synthetic case to demonstrate the impact of the geometry on the inversion result. This study shows that geometrical information in between electrodes are necessary to reconstruct finely the "true model". Finally, we apply the methodology to a real underground quarry pillar, implying one photogrammetric survey and three ERI surveys. The results show that the procedure can greatly improve the reconstruction and avoid some artifacts due to strong geometry variations.

Relation of historical quarrying, material utilization and performance on buildings in Eastern Finland

NASA Astrophysics Data System (ADS)

Luodes, Nike M.; Pirinen, Heikki

2016-04-01

Finland might seem to have lower stone heritage compared to other southern European countries, but it has been the main exporter of dimension stone to the majestic buildings that made St.Petersburg a recognized cultural heritage. In Finland, though, the stone seems undervalued. The only dramatic and predominant stone buildings are those of agencies and administrations located in the towns, where the stone has been used to impress and symbolize value. Romantic style used massive bossy stone in building's full height and created fine traditional carvings. Otherwise the communities have mainly built settlements in contact with the nature, with materials easily available and of low cost, following architectonical trends of the periods and producing interesting stone details. During the past years, research has been conducted on historical buildings interconnecting scientific and artistic approach to evaluate material durability and cultural relevance of the artifacts. Generally until mid 20th century the stone has been traditionally used massive for basements and walls. The materials still present good mechanical characteristics and most often the weathering level after hundreds of years of exposure had reached only the first millimeters from the curst. Instead the old methodology for deposit exploitation has left visible signs on the buildings. Some examples are visible from Kuopio. The exploitation of small, easy-to-reach surface deposits, even if planned by local experts, has affected quality and appearance of historical buildings. As an example the excavation of shallow quarries where also weathered crop was kept as a product has characterized the basement of the Niirala school that presents change in colors due to original material more than to weathering on site. Fissuring is also visible on a couple of blocks while marks on the rocks depict the old excavation method. Most often the deposits had been in the vicinities, frequently hidden by further construction activities under urban development. In cases where extension of relevant buildings, as for example Kuopio Lyceum, required new material, the original quarry might have not been any more available. Alternative material had to be found and changes in appearance between the construction ages might still be readable from the heterogeneity of the material. In few cases the material had been extracted from remote areas, for buildings symbolizing the town and when the appearance had been a predominant choice. In these cases the quarries are still visible and have been exploited also in more recent years. It might happen that their economical value is not anymore competitive with modern requirements, but still they represent an important material source to avoid restructuration with similar but unsuitable materials.

Competing English, Spanish, and French alabaster trade in Europe over five centuries as evidenced by isotope fingerprinting

PubMed Central

Kloppmann, W.; Leroux, L.; Bromblet, P.; Le Pogam, P.-Y.; Cooper, A. H.; Worley, N.; Guerrot, C.; Montech, A. T.; Gallas, A. M.; Aillaud, R.

2017-01-01

A lack of written sources is a serious obstacle in the reconstruction of the medieval trade of art and art materials, and in the identification of artists, workshop locations, and trade routes. We use the isotopes of sulfur, oxygen, and strontium (S, O, Sr) present in gypsum alabaster to unambiguously link ancient European source quarries and areas to alabaster artworks produced over five centuries (12th–17th) held by the Louvre museum in Paris and other European and American collections. Three principal alabaster production areas are identified, in central England, northern Spain, and a major, long-lived but little-documented alabaster trade radiating from the French Alps. The related trade routes are mostly fluvial, although terrestrial transport crossing the major river basin borders is also confirmed by historical sources. Our study also identifies recent artwork restoration using Italian alabaster and provides a robust geochemical framework for provenancing, including recognition of restoration and forgeries. PMID:29078309

Competing English, Spanish, and French alabaster trade in Europe over five centuries as evidenced by isotope fingerprinting.

PubMed

Kloppmann, W; Leroux, L; Bromblet, P; Le Pogam, P-Y; Cooper, A H; Worley, N; Guerrot, C; Montech, A T; Gallas, A M; Aillaud, R

2017-11-07

A lack of written sources is a serious obstacle in the reconstruction of the medieval trade of art and art materials, and in the identification of artists, workshop locations, and trade routes. We use the isotopes of sulfur, oxygen, and strontium (S, O, Sr) present in gypsum alabaster to unambiguously link ancient European source quarries and areas to alabaster artworks produced over five centuries (12th-17th) held by the Louvre museum in Paris and other European and American collections. Three principal alabaster production areas are identified, in central England, northern Spain, and a major, long-lived but little-documented alabaster trade radiating from the French Alps. The related trade routes are mostly fluvial, although terrestrial transport crossing the major river basin borders is also confirmed by historical sources. Our study also identifies recent artwork restoration using Italian alabaster and provides a robust geochemical framework for provenancing, including recognition of restoration and forgeries. Copyright © 2017 the Author(s). Published by PNAS.

Competing English, Spanish, and French alabaster trade in Europe over five centuries as evidenced by isotope fingerprinting

NASA Astrophysics Data System (ADS)

Kloppmann, W.; Leroux, L.; Bromblet, P.; Le Pogam, P.-Y.; Cooper, A. H.; Worley, N.; Guerrot, C.; Montech, A. T.; Gallas, A. M.; Aillaud, R.

2017-11-01

A lack of written sources is a serious obstacle in the reconstruction of the medieval trade of art and art materials, and in the identification of artists, workshop locations, and trade routes. We use the isotopes of sulfur, oxygen, and strontium (S, O, Sr) present in gypsum alabaster to unambiguously link ancient European source quarries and areas to alabaster artworks produced over five centuries (12th–17th) held by the Louvre museum in Paris and other European and American collections. Three principal alabaster production areas are identified, in central England, northern Spain, and a major, long-lived but little-documented alabaster trade radiating from the French Alps. The related trade routes are mostly fluvial, although terrestrial transport crossing the major river basin borders is also confirmed by historical sources. Our study also identifies recent artwork restoration using Italian alabaster and provides a robust geochemical framework for provenancing, including recognition of restoration and forgeries.

29 CFR 1926.909 - Firing the blast.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Firing the blast. (a) A code of blasting signals equivalent to Table U-1, shall be posted on one or more... blasts 5 minutes prior to blast signal. Blast Signal—A series of short blasts 1 minute prior to the shot...

29 CFR 1926.909 - Firing the blast.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Firing the blast. (a) A code of blasting signals equivalent to Table U-1, shall be posted on one or more... blasts 5 minutes prior to blast signal. Blast Signal—A series of short blasts 1 minute prior to the shot...

29 CFR 1926.909 - Firing the blast.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Firing the blast. (a) A code of blasting signals equivalent to Table U-1, shall be posted on one or more... blasts 5 minutes prior to blast signal. Blast Signal—A series of short blasts 1 minute prior to the shot...

29 CFR 1926.909 - Firing the blast.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Firing the blast. (a) A code of blasting signals equivalent to Table U-1, shall be posted on one or more... blasts 5 minutes prior to blast signal. Blast Signal—A series of short blasts 1 minute prior to the shot...

29 CFR 1926.909 - Firing the blast.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Firing the blast. (a) A code of blasting signals equivalent to Table U-1, shall be posted on one or more... blasts 5 minutes prior to blast signal. Blast Signal—A series of short blasts 1 minute prior to the shot...

40 CFR 60.141 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Primary Emissions from Basic Oxygen... A of this part. (a) Basic oxygen process furnace (BOPF) means any furnace with a refractory lining... additions into a vessel and introducing a high volume of oxygen-rich gas. Open hearth, blast, and...

40 CFR 60.141 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Primary Emissions from Basic Oxygen... A of this part. (a) Basic oxygen process furnace (BOPF) means any furnace with a refractory lining... additions into a vessel and introducing a high volume of oxygen-rich gas. Open hearth, blast, and...

40 CFR 60.141 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Primary Emissions from Basic Oxygen... A of this part. (a) Basic oxygen process furnace (BOPF) means any furnace with a refractory lining... additions into a vessel and introducing a high volume of oxygen-rich gas. Open hearth, blast, and...

40 CFR 60.141 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Primary Emissions from Basic Oxygen... A of this part. (a) Basic oxygen process furnace (BOPF) means any furnace with a refractory lining... additions into a vessel and introducing a high volume of oxygen-rich gas. Open hearth, blast, and...

40 CFR 60.141 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Primary Emissions from Basic Oxygen... A of this part. (a) Basic oxygen process furnace (BOPF) means any furnace with a refractory lining... additions into a vessel and introducing a high volume of oxygen-rich gas. Open hearth, blast, and...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Hazardous Air Pollutants for Primary Lead Smelting § 63.1541 Applicability. (a) The provisions of this subpart apply to the following affected sources at primary lead smelters: sinter machine, blast furnace... not apply to secondary lead smelters, lead refiners, or lead remelters. (b) Table 1 of this subpart...

Systemic reduction of rice blast by means of photosensitizers

USDA-ARS?s Scientific Manuscript database

Acquired disease resistance of plants may be induced by exogenous reactive oxygen species or their sources. Certain compounds (photosensitizers) produce ROS at the expense of light energy. This study used photodynamic dyes bengal rose and methylene blue, which yield singlet oxygen, and mercaptopyrid...

How Deep is Shallow? Improving Absolute and Relative Locations of Upper Crustal Seismicity in Switzerland

NASA Astrophysics Data System (ADS)

Diehl, T.; Kissling, E. H.; Singer, J.; Lee, T.; Clinton, J. F.; Waldhauser, F.; Wiemer, S.

2017-12-01

Information on the structure of upper-crustal fault systems and their connection with seismicity is key to the understanding of neotectonic processes. Precisely determined focal depths in combination with structural models can provide important insight into deformation styles of the upper crust (e.g. thin- vs. versus thick-skinned tectonics). Detailed images of seismogenic fault zones in the upper crust, on the other hand, will contribute to the assessment of the hazard related to natural and induced earthquakes, especially in regions targeted for radioactive waste repositories or geothermal energy production. The complex velocity structure of the uppermost crust and unfavorable network geometries, however, often hamper precise locations (i.e. focal depth) of shallow seismicity and therefore limit tectonic interpretations. In this study we present a new high-precision catalog of absolute locations of seismicity in Switzerland. High-quality travel-time data from local and regional earthquakes in the period 2000-2017 are used to solve the coupled hypocenter-velocity structure problem in 1D. For this purpose, the well-known VELEST inversion software was revised and extended to improve the quality assessment of travel-time data and to facilitate the identification of erroneous picks in the bulletin data. Results from the 1D inversion are used as initial parameters for a 3D local earthquake tomography. Well-studied earthquakes and high-quality quarry blasts are used to assess the quality of 1D and 3D relocations. In combination with information available from various controlled-source experiments, borehole data, and geological profiles, focal depths and associated host formations are assessed through comparison with the resolved 3D velocity structure. The new absolute locations and velocity models are used as initial values for relative double-difference relocation of earthquakes in Switzerland. Differential times are calculated from bulletin picks and waveform cross-correlation. The resulting double-difference catalog is used as a regional background catalog for a real-time double-difference approach. We will present our implementation strategy and test its performance for local applications using examples from well-recorded natural and induced earthquake sequences in Switzerland.

Near-source and Regional Experiments to Quantify Coupling and Propagation Effects of Seismic and Infrasound Signals from Mining Explosions

NASA Astrophysics Data System (ADS)

Stump, B. W.; Hayward, C.; Zhou, R.; House, S. M.

2001-12-01

Mining explosions designed to fragment rock are known to be regular sources of seismic waves as exemplified by the routine identification of these events in the USGS Mining Seismicity Report. Near-surface explosions can also generate low frequency acoustic waves or infrasound that can propagate through the atmosphere to regional distances. An understanding of source contributions to the size and character of waves initiated in the solid earth and atmosphere can be used to interpret propagation path effects as well as provide a physical understanding of characteristics that can be used for identifying the source type from the regional observations. The porphyry copper district of the SW United States was chosen for the study of these effects because of the existence of mining explosions that are routinely included in the USGS Mining Seismicity Report and an abundance of high quality regional seismic stations. A regional network of infrasound arrays was installed in order to quantify the accompanying low-frequency acoustic signals. In-mine seismic and acoustic measurements were made to quantify the source. These observations were supplemented with GPS locked video and in-mine documentation of the explosion design parameters. This comprehensive data set has been used to estimate source parameters that can be used to interpret the regional signals. Infrasound signals observed over a one-year time period indicate that the direction of atmospheric winds controls the amplitude and thus detection of these signals. Regional seismic observations are strongly affected by the style of blasting. The largest of the ground truth events (~250,000 kg explosive) are detonated in relatively long blasting sequences (~2 seconds) and produce some of the smallest regional signals. Smaller blasts (~25,000 to 50,000 kg) are detonated over relatively shorter time periods (`~0.2 to 0.4 seconds) and produce the largest regional signals. This source time function signature in the regional seismograms results in little relation between total explosive weight and peak regional amplitudes. Event locations based on the regional seismic network produces a location bias that is magnitude dependent and spans a region with a radius of over 30 km. Part of the location bias appears to be a result of improper identification of the emergent onset of the smaller events.

CrocoBLAST: Running BLAST efficiently in the age of next-generation sequencing.

PubMed

Tristão Ramos, Ravi José; de Azevedo Martins, Allan Cézar; da Silva Delgado, Gabrielle; Ionescu, Crina-Maria; Ürményi, Turán Peter; Silva, Rosane; Koca, Jaroslav

2017-11-15

CrocoBLAST is a tool for dramatically speeding up BLAST+ execution on any computer. Alignments that would take days or weeks with NCBI BLAST+ can be run overnight with CrocoBLAST. Additionally, CrocoBLAST provides features critical for NGS data analysis, including: results identical to those of BLAST+; compatibility with any BLAST+ version; real-time information regarding calculation progress and remaining run time; access to partial alignment results; queueing, pausing, and resuming BLAST+ calculations without information loss. CrocoBLAST is freely available online, with ample documentation (webchem.ncbr.muni.cz/Platform/App/CrocoBLAST). No installation or user registration is required. CrocoBLAST is implemented in C, while the graphical user interface is implemented in Java. CrocoBLAST is supported under Linux and Windows, and can be run under Mac OS X in a Linux virtual machine. jkoca@ceitec.cz. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

A Historical Summary of the Work of the Corps of Engineers in Washington D.C. and Vicinity 1852 - 1952

DTIC Science & Technology

1952-01-01

built , and all land in Maryland needed for the conduit had been condemned . A first-class sand- stone quarry at Seneca , seven miles above Great Falls...constructed of Seneca Creek freestone obtained from the Bull Run quarry about twenty-three miles from Washington o By 1852 ~ the work was completed 9 except...pro- vided funds for an arsenal. Tragedy stalked the area in the ensuin8 years. In 1814, the arsenal was destroyed by the British, who lost

Design of a Free-running, 1/30th Froude Scaled Model Destroyer for In-situ Hydrodynamic Flow Visualization

DTIC Science & Technology

2012-06-01

Accessed 21 March 2012]. [12] ITTC Resistance Committee, "Final Report and Recommendations to the 26th ITTC," SNAME, Rio de Janeiro , 2011. [13] E. V...operating in open water, whether it is the Charles River or a local rock quarry, the depth to draft ratio will remain above the minimum value of...e.g. the Charles River , Boston Harbor, or a local rock quarry. The model will serve as a flexible test platform for future research within the MIT

Trichomonas gallinae Persistence in Four Water Treatments.

PubMed

Purple, Kathryn E; Humm, Jacob M; Kirby, R Brian; Saidak, Christina G; Gerhold, Richard

2015-07-01

Trichomonas gallinae is a protozoan parasite commonly found in columbids, passerines, and several raptor species. Although T. gallinae is thought to spread between individuals and across species through shared water sources, little research has been conducted regarding the persistence of T. gallinae in the environment. To determine the persistence of T. gallinae in various communal water sources, we inoculated 1 × 10(6) trichomonads into 500 mL samples of distilled water, quarry water, bird bath water, and rain barrel water in two replicates. Aliquots of 0.5 mL were collected from each source at -1, 0, 15, 30, and 60 min; aliquots were incubated at 37 C and examined for trichomonads by light microscopy for five consecutive days. Live trichomonads were observed in all samples and at all sampling times except prior to inoculation (-1 min). The pH of water sources ranged from an average of 5.9 to 7.4 postsampling. Our findings indicate that T. gallinae can persist for up to 60 min in various water treatments and thus be infectious for birds drinking T. gallinae-contaminated water.

DECONVOLUTION OF IMAGES FROM BLAST 2005: INSIGHT INTO THE K3-50 AND IC 5146 STAR-FORMING REGIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roy, Arabindo; Netterfield, Calvin B.; Ade, Peter A. R.

2011-04-01

We present an implementation of the iterative flux-conserving Lucy-Richardson (L-R) deconvolution method of image restoration for maps produced by the Balloon-borne Large Aperture Submillimeter Telescope (BLAST). Compared to the direct Fourier transform method of deconvolution, the L-R operation restores images with better-controlled background noise and increases source detectability. Intermediate iterated images are useful for studying extended diffuse structures, while the later iterations truly enhance point sources to near the designed diffraction limit of the telescope. The L-R method of deconvolution is efficient in resolving compact sources in crowded regions while simultaneously conserving their respective flux densities. We have analyzed itsmore » performance and convergence extensively through simulations and cross-correlations of the deconvolved images with available high-resolution maps. We present new science results from two BLAST surveys, in the Galactic regions K3-50 and IC 5146, further demonstrating the benefits of performing this deconvolution. We have resolved three clumps within a radius of 4.'5 inside the star-forming molecular cloud containing K3-50. Combining the well-resolved dust emission map with available multi-wavelength data, we have constrained the spectral energy distributions (SEDs) of five clumps to obtain masses (M), bolometric luminosities (L), and dust temperatures (T). The L-M diagram has been used as a diagnostic tool to estimate the evolutionary stages of the clumps. There are close relationships between dust continuum emission and both 21 cm radio continuum and {sup 12}CO molecular line emission. The restored extended large-scale structures in the Northern Streamer of IC 5146 have a strong spatial correlation with both SCUBA and high-resolution extinction images. A dust temperature of 12 K has been obtained for the central filament. We report physical properties of ten compact sources, including six associated protostars, by fitting SEDs to multi-wavelength data. All of these compact sources are still quite cold (typical temperature below {approx} 16 K) and are above the critical Bonner-Ebert mass. They have associated low-power young stellar objects. Further evidence for starless clumps has also been found in the IC 5146 region.« less

Deconvolution of Images from BLAST 2005: Insight into the K3-50 and IC 5146 Star-forming Regions

NASA Astrophysics Data System (ADS)

Roy, Arabindo; Ade, Peter A. R.; Bock, James J.; Brunt, Christopher M.; Chapin, Edward L.; Devlin, Mark J.; Dicker, Simon R.; France, Kevin; Gibb, Andrew G.; Griffin, Matthew; Gundersen, Joshua O.; Halpern, Mark; Hargrave, Peter C.; Hughes, David H.; Klein, Jeff; Marsden, Gaelen; Martin, Peter G.; Mauskopf, Philip; Netterfield, Calvin B.; Olmi, Luca; Patanchon, Guillaume; Rex, Marie; Scott, Douglas; Semisch, Christopher; Truch, Matthew D. P.; Tucker, Carole; Tucker, Gregory S.; Viero, Marco P.; Wiebe, Donald V.

2011-04-01

We present an implementation of the iterative flux-conserving Lucy-Richardson (L-R) deconvolution method of image restoration for maps produced by the Balloon-borne Large Aperture Submillimeter Telescope (BLAST). Compared to the direct Fourier transform method of deconvolution, the L-R operation restores images with better-controlled background noise and increases source detectability. Intermediate iterated images are useful for studying extended diffuse structures, while the later iterations truly enhance point sources to near the designed diffraction limit of the telescope. The L-R method of deconvolution is efficient in resolving compact sources in crowded regions while simultaneously conserving their respective flux densities. We have analyzed its performance and convergence extensively through simulations and cross-correlations of the deconvolved images with available high-resolution maps. We present new science results from two BLAST surveys, in the Galactic regions K3-50 and IC 5146, further demonstrating the benefits of performing this deconvolution. We have resolved three clumps within a radius of 4farcm5 inside the star-forming molecular cloud containing K3-50. Combining the well-resolved dust emission map with available multi-wavelength data, we have constrained the spectral energy distributions (SEDs) of five clumps to obtain masses (M), bolometric luminosities (L), and dust temperatures (T). The L-M diagram has been used as a diagnostic tool to estimate the evolutionary stages of the clumps. There are close relationships between dust continuum emission and both 21 cm radio continuum and 12CO molecular line emission. The restored extended large-scale structures in the Northern Streamer of IC 5146 have a strong spatial correlation with both SCUBA and high-resolution extinction images. A dust temperature of 12 K has been obtained for the central filament. We report physical properties of ten compact sources, including six associated protostars, by fitting SEDs to multi-wavelength data. All of these compact sources are still quite cold (typical temperature below ~ 16 K) and are above the critical Bonner-Ebert mass. They have associated low-power young stellar objects. Further evidence for starless clumps has also been found in the IC 5146 region.

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

Nuclear Power System Architecture and Safety Study- Feasibility of Launch Pad Explosion Simulation using Radios

NASA Astrophysics Data System (ADS)

Destefanis, Stefano; Tracino, Emanuele; Giraudo, Martina

2014-06-01

During a mission involving a spacecraft using nuclear power sources (NPS), the consequences to the population induced by an accident has to be taken into account carefully.Part of the study (led by AREVA, with TAS-I as one of the involved parties) was devoted to "Worst Case Scenario Consolidation". In particular, one of the activities carried out by TAS-I had the aim of characterizing the accidental environment (explosion on launch pad or during launch) and consolidate the requirements given as input in the study. The resulting requirements became inputs for Nuclear Power Source container design.To do so, TAS-I did first an overview of the available technical literature (mostly developed in the frame of NASA Mercury / Apollo program), to identify the key parameters to be used for analytical assessment (blast pressure wave, fragments size, speed and distribution, TNT equivalent of liquid propellant).Then, a simplified Radioss model was setup, to verify both the cards needed for blast / fragment impact analysis and the consistency between preliminary results and available technical literature (Radioss is commonly used to design mine - resistant vehicles, by simulating the effect of blasts onto structural elements, and it is used in TAS-I for several types of analysis, including land impact, water impact and fluid - structure interaction).The obtained results (albeit produced by a very simplified model) are encouraging, showing that the analytical tool and the selected key parameters represent a step in the right direction.

Zarzalejo granite (Spain). A nomination for 'Global Heritage Stone Resource'

NASA Astrophysics Data System (ADS)

Freire Lista, David Martin; Fort, Rafael; José Varas-Muriel, María

2015-04-01

Zarzalejo granite is quarried in the Sierra de Guadarrama (Spanish Central System) foothills, in and around Zarzalejo village, in the province of Madrid, Spain. It is an inequigranular monzogranite medium-to-coarse grained, with a slight porphyritic texture (feldspar phenocrysts) and mafic micro-grained enclaves. In this abstract the candidacy of Zarzalejo granite as a "Global Heritage Resource Stone" (GHSR) is presented. This stone ideally fits the newly proposed designation as it has been used in many heritage buildings and its good petrophysical properties and durability have allowed well preserved constructions such as a Roman road, San Pedro Church in Zarzalejo (1492), Descalzas Reales Monastery in Madrid (1559-1564) and the San Lorenzo del Escorial Royal Monastery (1563-1584), to be declared a World Heritage Site by UNESCO. This level of construction has been a landmark in the extraction and proliferation of historic quarries created due to the high demand that such colossal monuments and buildings with granite, have required for their construction. In the mid-20th century, More, Zarzalejo granite has also been used in restoration works including the Royal Palace and the Reina Sofía Museum (2001-2005), both buildings in Madrid, Spain. Extraction of granite ashlars from tors has been a very frequent activity in the Zarzalejo neighbourhood until mid-twentieth century. So there is also a need to preserve these historic quarries. This type of stone has created a landscape that has been preserved as an open-air museum today where you can see the marks left in the granite due to historic quarry operations. The granite industry has been one of the main pillars of the Zarzalejo regional economy. For centuries, the local community have been engaged in quarrying and have created a cultural landscape based on its building stone. A quarryman monument has been erected in Zarzalejo in honor of this traditional craft as well as an architecture museum at San Lorenzo del Escorial Monastery, which shows the building material used during its construction. There is currently an active quarry of this dimension stone which continues to be sold under the commercial name of "Gris Escorial". Zarzalejo granite is mainly exported to Turkey, Italy and Saudi Arabia. Today this stone is used primarily in flooring. Other uses include cobblestones, funeral art, and building and monument restoration and rehabilitation. Sculptures have also built in recent years, notably the great monoliths in Salvador Dalí Square (1989) in Madrid. There are also small historic family-run quarries intermittently continuing this dimension stone carving tradition. Given its characteristics, Zarzalejo granite meets the requisites proposed to be nominated as a GHSR. This nomination will contribute to raising awareness and disseminate key aspects for conservation and thus ensure its use as a replacement stone in restoring heritage buildings where it was used as a building stone. Acknowledgements This study was funded by the Community of Madrid under the GEOMATERIALS 2 project (S2013/MIT-2914). The authors are members of the Complutense University of Madrid's Research Group: "Alteración y Conservación de los Materiales Pétreos del Patrimonio" (ref. 921349).

Windows .NET Network Distributed Basic Local Alignment Search Toolkit (W.ND-BLAST)

PubMed Central

Dowd, Scot E; Zaragoza, Joaquin; Rodriguez, Javier R; Oliver, Melvin J; Payton, Paxton R

2005-01-01

Background BLAST is one of the most common and useful tools for Genetic Research. This paper describes a software application we have termed Windows .NET Distributed Basic Local Alignment Search Toolkit (W.ND-BLAST), which enhances the BLAST utility by improving usability, fault recovery, and scalability in a Windows desktop environment. Our goal was to develop an easy to use, fault tolerant, high-throughput BLAST solution that incorporates a comprehensive BLAST result viewer with curation and annotation functionality. Results W.ND-BLAST is a comprehensive Windows-based software toolkit that targets researchers, including those with minimal computer skills, and provides the ability increase the performance of BLAST by distributing BLAST queries to any number of Windows based machines across local area networks (LAN). W.ND-BLAST provides intuitive Graphic User Interfaces (GUI) for BLAST database creation, BLAST execution, BLAST output evaluation and BLAST result exportation. This software also provides several layers of fault tolerance and fault recovery to prevent loss of data if nodes or master machines fail. This paper lays out the functionality of W.ND-BLAST. W.ND-BLAST displays close to 100% performance efficiency when distributing tasks to 12 remote computers of the same performance class. A high throughput BLAST job which took 662.68 minutes (11 hours) on one average machine was completed in 44.97 minutes when distributed to 17 nodes, which included lower performance class machines. Finally, there is a comprehensive high-throughput BLAST Output Viewer (BOV) and Annotation Engine components, which provides comprehensive exportation of BLAST hits to text files, annotated fasta files, tables, or association files. Conclusion W.ND-BLAST provides an interactive tool that allows scientists to easily utilizing their available computing resources for high throughput and comprehensive sequence analyses. The install package for W.ND-BLAST is freely downloadable from . With registration the software is free, installation, networking, and usage instructions are provided as well as a support forum. PMID:15819992

Assessing the role of coastal characteristics in erosional process of rocky shores by boulder quarrying.

NASA Astrophysics Data System (ADS)

Causon Deguara, Joanna; Gauci, Ritienne

2017-04-01

Rocky coasts are considered as relatively stable coastlines, subject to erosional processes that change the landscape over long periods of time. Block quarrying is one such process, occurring when hydraulic pressure from wave impact dislodges boulders from within the outcropping bedrock. These dislodged boulders can be either deposited inland or dragged seaward by further wave action. This process can be evidenced from boulder deposits on the coast, as well as sockets and detachment scarps that are identified at the shoreline and in the backshore. This study seeks to identify the role of attributes such as aspect, geological structure and water depth have on erosion of rocky coasts through boulder quarrying processes. This is being done through observation of coastline morphology and an analysis of boulder accumulations and erosional features identified on a 3km stretch of rocky shore. The study area is situated on the SE coast of the Island of Malta (Central Mediterranean). The coastline being analysed generally trends NW - SE and consists of a series of limestone beds that dip slightly towards the NE. The boulder deposits observed along the site vary in size, quantity and position with respect to the shoreline. Whilst some areas exhibit large boulder accumulations, other areas are distinguished by the complete absence of such deposits. Taking into consideration the wave climate, the variable size, quantity and distribution of boulder accumulations observed along the site may indicate that geological structure and aspect play an important role in boulder dislodgment by wave action. Key words: rock coast, boulder quarrying, erosional process, Malta

Aging and Curing Temperature Effects on Compressive Strength of Mortar Containing Lime Stone Quarry Dust and Industrial Granite Sludge.

PubMed

Amin, Muhammad Nasir; Khan, Kaffayatullah; Saleem, Muhammad Umair; Khurram, Nauman; Niazi, Muhammad Umar Khan

2017-06-11

In this study, the researchers investigated the potential use of locally available waste materials from the lime stone quarry and the granite industry as a partial replacement of cement. Quarry sites and granite industry in the eastern province of Saudi Arabia produces tons of powder wastes in the form of quarry dust (QD) and granite sludge (GS), respectively, causing serious environmental problems along with frequent dust storms in the area. According to ASTM C109, identical 50-mm3 specimens were cast throughout this study to evaluate the compressive strength development of mortars (7, 28 and 91 days) containing these waste materials. Experimental variables included different percentage replacement of cement with waste materials (GS, QD), fineness of GS, various curing temperatures (20, 40 and 60 °C as local normal and hot environmental temperatures) and curing moisture (continuously moist and partially moist followed by air curing). Finally, the results of mortar containing waste materials were compared to corresponding results of control mortar (CM) and mortar containing fly ash (FA). The test results indicated that under normal curing (20 °C, moist cured), the compressive strength of mortar containing the different percentage of waste materials (QD, GS, FA and their combinations) remained lower than that of CM at all ages. However, the compressive strength of mortar containing waste materials slightly increased with increased fineness of GS and significantly increased under high curing temperatures. It was recommended that more fineness of GS be achieved to use its high percentage replacement with cement (30% or more) incorporating local environmental conditions.

Aging and Curing Temperature Effects on Compressive Strength of Mortar Containing Lime Stone Quarry Dust and Industrial Granite Sludge

PubMed Central

Amin, Muhammad Nasir; Khan, Kaffayatullah; Saleem, Muhammad Umair; Khurram, Nauman; Niazi, Muhammad Umar Khan

2017-01-01

In this study, the researchers investigated the potential use of locally available waste materials from the lime stone quarry and the granite industry as a partial replacement of cement. Quarry sites and granite industry in the eastern province of Saudi Arabia produces tons of powder wastes in the form of quarry dust (QD) and granite sludge (GS), respectively, causing serious environmental problems along with frequent dust storms in the area. According to ASTM C109, identical 50-mm3 specimens were cast throughout this study to evaluate the compressive strength development of mortars (7, 28 and 91 days) containing these waste materials. Experimental variables included different percentage replacement of cement with waste materials (GS, QD), fineness of GS, various curing temperatures (20, 40 and 60 °C as local normal and hot environmental temperatures) and curing moisture (continuously moist and partially moist followed by air curing). Finally, the results of mortar containing waste materials were compared to corresponding results of control mortar (CM) and mortar containing fly ash (FA). The test results indicated that under normal curing (20 °C, moist cured), the compressive strength of mortar containing the different percentage of waste materials (QD, GS, FA and their combinations) remained lower than that of CM at all ages. However, the compressive strength of mortar containing waste materials slightly increased with increased fineness of GS and significantly increased under high curing temperatures. It was recommended that more fineness of GS be achieved to use its high percentage replacement with cement (30% or more) incorporating local environmental conditions. PMID:28772999

Investigation of intact rock geomechanical parameters' effects on commercial blocks' productivity within stone reserves: A case history of some quarries in Isfahan, Iran

NASA Astrophysics Data System (ADS)

Yarahmadi, Reza; Bagherpour, Raheb; Tabaei, Morteza; Sousa, Luis M. O.

2017-10-01

One of the common methods to determine commercial blocks productivity (CBP) in reserves of dimension stone is through the study of the discontinuities' network. However, this determination remains a difficult task due to geographical heterogeneity and lack of access to all reserves' formations. This study presents a new method based on various geomechanical tests performed on intact rocks that assessed the CBP of a dimension stones' rock mass. Assuming that a dimension stone's rock mass comprised a large block of an intact rock, due to tectonics, the geomechanical properties of this block had direct effects on the discontinuities created within it. Therefore, the geomechanical properties of the intact rock may be related to the CBP of a stone reserve. Based on this factor, this study explored the relationship among some geomechanical properties, including failure angle, uniaxial compressive strength, and modulus of elasticity, and CBP by using data acquired from 21 dimension stone quarries consisting of travertine, marble, and onyx groups. According to the results obtained from the analysis of the Isfahan province's Iranian quarries, failure angle was not highly related to the reserve's CBP. In marble quarries, CBP may decrease, if the compressive strength of an intact rock exceeds 60 MPa. Among the studied parameters, the saturated-to-dry ratio's modulus of elasticity had the greatest relationship to the CBP. Generally, the presented diagrams displayed that the correlation between geomechanical properties and the CBP were an appropriate guide in determining the potential cost-effectiveness of a accessing a particular rock reserve during the early exploration phase.

Role of transient water pressure in quarrying: A subglacial experiment using acoustic emissions

USGS Publications Warehouse

Cohen, D.; Hooyer, T.S.; Iverson, N.R.; Thomason, J.F.; Jackson, M.

2006-01-01

Probably the most important mechanism of glacial erosion is quarrying: the growth and coalescence of cracks in subglacial bedrock and dislodgement of resultant rock fragments. Although evidence indicates that erosion rates depend on sliding speed, rates of crack growth in bedrock may be enhanced by changing stresses on the bed caused by fluctuating basal water pressure in zones of ice-bed separation. To study quarrying in real time, a granite step, 12 cm high with a crack in its stoss surface, was installed at the bed of Engabreen, Norway. Acoustic emission sensors monitored crack growth events in the step as ice slid over it. Vertical stresses, water pressure, and cavity height in the lee of the step were also measured. Water was pumped to the lee of the step several times over 8 days. Pumping initially caused opening of a leeward cavity, which then closed after pumping was stopped and water pressure decreased. During cavity closure, acoustic emissions emanating mostly from the vicinity of the base of the crack in the step increased dramatically. With repeated pump tests this crack grew with time until the step's lee surface was quarried. Our experiments indicate that fluctuating water pressure caused stress thresholds required for crack growth to be exceeded. Natural basal water pressure fluctuations should also concentrate stresses on rock steps, increasing rates of crack growth. Stress changes on the bed due to water pressure fluctuations will increase in magnitude and duration with cavity size, which may help explain the effect of sliding speed on erosion rates. Copyright 2006 by the American Geophysical Union.

Liquid disinfection using power impulse laser

NASA Astrophysics Data System (ADS)

Gribin, S.; Assaoul, Viktor; Markova, Elena; Gromova, Ludmila P.; Spesivtsev, Boris; Bazanov, V.

1996-05-01

The presented method is based on the bactericidal effect of micro-blast induced by various sources (laser breakdown, electrohydraulic effect...). Using elaborated conception of physical phenomena providing liquid disinfection it is possible to determine optimal conditions of water treatment. The problem of optimization is solved using methods of mathematical modeling and special experiments.

Family as a Total Package: Restoring and Enhancing Psychological Health for Citizen Soldiers and Families

DTIC Science & Technology

2014-03-14

Kurt Goldstein, 1878-1965 Traumatic Brain Injury (TBI)*  Before Vietnam • “Shell shock” initially meant nervous system damage from concussive blast...TBIs ( football , vehicle accidents). • Information is readily available for service members, veterans and civilians. *Various sources; MacDonald et

Liquid disinfection using power impulse laser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gribin, S.; Assaoul, V.; Markova, E.

1996-12-31

The presented method is based on the bactericidal effect of micro-blast induced by various sources (laser breakdown, electrohydraulic effect ... ). Using elaborated conception of physical phenomena providing liquid disinfection it is possible to determine optimal conditions of water treatment. The problem of optimization is solved using methods of mathematical modeling and special experiments.

40 CFR 63.11514 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... weight (of the metal), as shown in formulation data provided by the manufacturer or supplier, such as the Material Safety Data Sheet for the material. (1) A dry abrasive blasting affected source is the collection... and Equipment Finishing Operations; (7) Iron and Steel Forging; (8) Primary Metal Products...

Hardy Star Survives Supernova Blast

NASA Image and Video Library

2014-03-20

This composite image contains data from Chandra (purple) that provides evidence for the survival of a companion star from the blast of a supernova explosion. Chandra's X-rays reveal a point-like source in the supernova remnant at the location of a massive star. The data suggest that mass is being pulled away from the massive star towards a neutron star or a black hole companion. If confirmed, this would be only the third binary system containing both a massive star and a neutron star or black hole ever found in the aftermath of a supernova. This supernova remnant is found embedded in clouds of ionized hydrogen, which are shown in optical light (yellow and cyan) from the MCELS survey, along with additional optical data from the DSS (white).

Greener durable concretes through geopolymerisation of blast furnace slag

NASA Astrophysics Data System (ADS)

Rajamane, N. P.; Nataraja, M. C.; Jeyalakshmi, R.; Nithiyanantham, S.

2015-05-01

The eco-friendliness of concrete is quantified by parameters such as ‘embodied energy’ (EE) and ‘embodied CO2 emission’ (ECO2e), besides duration of designed ‘service life’. It may be noted that ECO2e is also referred as carbon footprint (CF) in the literature. Geopolymer (GP) is an inorganic polymeric gel, a type of amorphous alumino-silicate product, which can be synthesised by polycondensation reactions. The concrete reported in this paper was prepared using industrial wastes in the form of blast furnace slag, fly ash as geopolymeric source materials and sodium silicate and sodium hydroxide as activators. Many mechanical properties such as compressive strength, chloride diffusion, steel corrosion, rapid chloride permeability test and rapid migration test are compared with Portland cement.

Natural versus anthropogenic genesis of mardels (closed depressions) on the Gutland plateau (Luxembourg); archaeometrical and palynological evidence of Roman clay excavation from mardels.

NASA Astrophysics Data System (ADS)

van Mourik, Jan; Braekmans, Dennis; Doorenbosch, Marieke; Kuijper, Wim; van der Plicht, Hans

2016-04-01

Mardels, small closed depressions, are distinctive landforms on the Luxembourger Gutland plateau. In the present landscape most mardels are shallow fens, filled with colluvial sediments. The genesis of mardels has been studied intensively, inside and outside Luxembourg. Some researchers suggested a natural development and consider mardels as subsidence basins due to subsurface solution of gypsum veins, other researchers suggested cultural causes and consider mardels as prehistorical quarries. In the Gutland, mardels occur on various substrates. Mardels on the Strassen marls (li3) are abandoned quarries, related to clay excavation in Roman Time. Mardels on the Luxembourger sandstone (li2) are sinkholes, related to joint patterns in the sandstone formation. Mardels on the Keuper marls (km1,3) are originally subsidence basins, related to subsurface dissolutions of gypsum lenses and veins, filled with colluvial clay. The results of pollen analysis and archaeometrical tests demonstrate Roman extraction of clay for the production of ancient ceramics. So, the natural depressions have been enlarged to the present mardels. After excavation, the sedimentation of colluvium restarted in the abandoned quarries.

Analysis of conditions and the concept of multidirectional revitalization of the dolomite quarry in Siewierz

NASA Astrophysics Data System (ADS)

Pawełczyk, Katarzyna

2018-01-01

The development of mining of rock raw materials in Poland has significantly contributed to economic growth and the quality of life of local communities. However, mining activity, besides a number of positive effects, also implies broadly understood changes in the environment and the formation of brownfields. Reclamation and redevelopment of post-industrial areas, and especially post-mining areas, is currently a huge environmental and socio-economic challenge. Revitalization of post-mining areas is particularly important for small towns and municipalities, where mining was one of the main pillars of development and prosperity. An example of such a municipality is Siewierz in Silesian Voivodship. In the paper analysis the conditions have been conducted and the concept of revitalization of dolomite quarry Górnicze Zakłady Dolomitowe S.A. has been proposed. The AHP method has been used to analyse and select the optimal method of revitalization. As a result of the analysis, the concept of multidirectional revitalization with socially, economically and environmentally beneficial functions has been created, maximizing the potential of the quarry.

Mines, Quarries and Landscape. Visuality and Transformation

NASA Astrophysics Data System (ADS)

Jimeno, Carlos López; Torrijos, Ignacio Díez; González, Carmen Mataix

2016-06-01

In this paper a review of two basic concepts is carried out: scenery and landscape integration, proposing a new concept: "visuality", alternative to the classical "visibility" used in landscape studies related to mining activity, which explores the qualitative aspects that define the visual relationships between observer and environment. In relation to landscape integration studies, some reflections on substantive issues are made which induce certain prejudices at the time of addressing the issue of mining operations landscape integration, and some guidance and integration strategies are formulated. In the second part of the text, a new approach to the landscape integration of mines and quarries is raised, closely linked to the concept of visuality which are based on a basic goal: the re-qualification of the place, and give innovative answers to re-qualify the place and show how to catch the opportunity in the deep transformation generated by the development of mining activities. As a conclusion, a case study is presented in the last section, the landscape integration study conducted on marble exploitations Coto Pinos (Alicante, Spain), considered the largest ornamental rock quarry in Europe.

ESR spectroscopy as a tool for identifying joining fragments of antique marbles: the example of a pulpit by Donatello and Michelozzo.

PubMed

Attanasio, D; Platania, R

2000-06-01

ESR spectroscopy is one of the physicochemical techniques used to characterize archaeological white marbles and obtain information about their quarries of provenance. This is done by measuring selected spectral features of the Mn(2+) impurity ubiquitously present in marbles and developing a statistical classification rule from the variable vectors measured for a significant number of samples of known provenance (the quarry database). Now we show that the overall variability exhibited by the same spectroscopic features decreases rapidly with the linear dimensions of the sampled block and can be used to distinguish fragments belonging to the same piece of stone from those simply originating from the same quarry. Application of the method to the seven marble panels of the Donatello pulpit in Prato (Tuscany) shows that they have all been cut from the same single block and their different degradation must be ascribed to differential weathering and to the different conservation treatments undergone in the past. The limits and possible drawbacks of the method are also discussed. Copyright 2000 Academic Press.

Computer assisted blast design and assessment tools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cameron, A.R.; Kleine, T.H.; Forsyth, W.W.

1995-12-31

In general the software required by a blast designer includes tools that graphically present blast designs (surface and underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread. An example of the tools that are becoming available includes: Automatic blast pattern generation and underground ring design; blast design evaluation in terms of explosive distribution and detonation simulation; fragmentation prediction; blast vibration prediction and minimization; blast monitoring for assessment of dynamic performance; vibration measurement, display and signal processing;more » evaluation of blast results in terms of fragmentation; and risk and reliability based blast assessment. The authors have identified a set of criteria that are essential in choosing appropriate software blasting tools.« less

Water resources of the Iroquois National Wildlife Refuge, Genesee and Orleans counties, New York 2008-2010

USGS Publications Warehouse

Kappel, William M.; Jennings, Matthew B.

2012-01-01

A 2-year study of the water resources of the Iroquois National Wildlife Refuge (Refuge) in western New York was carried out in 2009-2010 in cooperation with the U.S. Fish and Wildlife Service to assist the Refuge in the development of a 15-year Comprehensive Conservtion plan. The study focused on Oak Orchard Creek, which flows through the Refuge, the groundwater resources that underlie the Refuge, and the possible changes to these resources related to the potential development of a bedrock quarry along the northern side of the Refuge. Oak Orchard Creek was monitored seasonally for flow and water quality; four tributary streams, which flowed only during early spring, also were monitored. A continuous streamgage was operated on Oak Orchard Creek, just north of the Refuge at Harrison Road. Four bedrock wells were drilled within the Refuge to determine the type and thickness of unconsolidated glacial sediments and to characterize the thickness and type of bedrock units beneath the Refuge, primarily the Lockport Dolomite. Water levels were monitored in 17 wells within and adjacent to the Refuge and water-quality samples were collected from 11 wells and 6 springs and analyzed for physical properties, nutrients, major ions, and trace metals. Flow in Oak Orchard Creek is from two different sources. During spring runoff, flow from the Onondaga Limestone Escarpment, several miles south of the Refuge, supplements surface-water runoff and groundwater discharge from the Salina Group to the south and east of the Refuge. Flow to Oak Orchard Creek also comes from surface-water runoff from the Lockport Dolomite Escarpment, north of the Refuge, and from groundwater discharging from the Lockport Dolomite and unconsolidated deposits that overlie the Lockport Dolomite. During the summer and fall low-flow period, only small quantities of groundwater flow from the Salina shales and Lockport Dolomite bedrock and the unconsolidated sediments that overlie them; most of this flow is lost to wetland evapotranspiration, and the remainder enters Oak Orchard Creek. Water quality in the Oak Orchard Creek is affected not only by these groundwater sources but also by surface runoff from agricultural areas and the New York State Wildlife Management Area east of the Refuge. Based on the results of the drilling program, the Lockport Dolomite underlies nearly all the Refuge. The Refuge wetlands lie within a bedrock trough between the Lockport Dolomite and Onondaga Limestone Escarpments, to the north and south, respectively. This bedrock trough was filled with mostly fine-grained sediments when Glacial Lake Tonawanda was present following the last period of glaciation. These fine-grained sediments became the substrate on which the wetlands were formed along Oak Orchard Creek and nearby Tonawanda Creek, to the south and west. Water quality in the unconsolidated and bedrock aquifers is variable; poor quality water (sulfide-rich "black water") generally is present south of Oak Orchard Creek and better quality water to the north where the Lockport Dolomite is close to the land surface. A set of springs, the Oak Orchard Acid Springs, is present within the Refuge; the springs are considered unique in New York State because of their naturally low pH (approximately 2.0) and their continual discharge of natural gas. The potential development of a bedrock quarry in the Lockport Dolomite bedrock along the northern border of the Refuge may affect the nearby Refuge wetlands. The extent of drawdown needed to actively quarry the bedrock could change the local hydrology and affect groundwater-flow directions and rates, primarily in the Lockport Dolomite bedrock and possibly the Oak Orchard Acid Springs area, farther to the south. The effect on the volume of flow in Oak Orchard Creek would probably be minimal as a result of the poor interaction between the surface-water and the groundwater systems. Of greater potential effect will be the possible change in the quality of water flowing into the Refuge from the discharge of groundwater during dewatering operations at the quarry; this discharge will flow into the northern part of the Refuge and affect the quantity and quality of wetland areas downstream from the quarry discharge. These changes may affect wetland management activities because of the potential for poorquality water to affect the ecology of the wetlands and the wildlife that use these wetlands.

Maastrichtian sedimentation and palaeoenvironments of the Saratov Volga region

NASA Astrophysics Data System (ADS)

Iakovishina, Elena; Blinova, Irina; Kopaevich, Ludmila; Vishnevskaya, Valentina; Bordunov, Sergey

2016-04-01

The Saratov Volga region was a shallow-marine epicontinental basin North-Eastern shelf zone of the Tethys Ocean in the Maastrichtian. The basis for the modeling conditions of sedimentation was the detection mineral composition of rocks, as well as the contents of various chemical elements in rocks in three reference sections: Lower Bannovka, quarries "Bolshevik" and "Kommunar". Rocks of quarries "Bolshevik" and "Kommunar" characterized by quartz-calcite mineral association. The main rock-forming mineral is calcite, small amounts in rocks contain quartz. Other mineral composition characterized section Lower Bannovka. At the base of the section in the rock marked the presence of the opal. The source of silica are radiolarians. Favorable conditions for the existence of which is cold deep water enriched with SiO2. Above the section marked authigenic glauconite, which are confined to zones of skip in sedimentation.Further up begins to dominate the accumulation of calcite with rich bentic foraminifera. Clay minerals in rocks of the section Lower Bannovka presented montmorillonite and illite. The relationship of chemical elements and their alkali modules allow to detail the conditions of sedimentation. The ratio of Fe/Mn in them varies from 44 to 5729. Higher values are characteristic of glauconite sandstones. Up the section marked decrease in the Ti/Zr, indicating that the increase in the distance from the source area to the place of deposition. The similarity values of the ratio Ti/Zr samples indicates a community source area. Sedimentation Model revealed the impact of the PreUral strait connecting Tethys and Paleoarktic. Through the Strait of deep cold water saturated with SiO2, penetrated into the of the Saratov Volga region, were accumulated clay. The closing of the PreUral Strait changed the conditions of sedimentation, the associated fall in sea levels due to global cooling reflected in the crisis of radiolarians, increase in the number of glauconite. Subsequent warming and warm-water transgression caused dominance of carbonates. The work was supported by grants 15-05-04990, 15-05-04700 Russian Foundation for Basic Research and IGCP project 609.

Low-cost blast wave generator for studies of hearing loss and brain injury: blast wave effects in closed spaces.

PubMed

Newman, Andrew J; Hayes, Sarah H; Rao, Abhiram S; Allman, Brian L; Manohar, Senthilvelan; Ding, Dalian; Stolzberg, Daniel; Lobarinas, Edward; Mollendorf, Joseph C; Salvi, Richard

2015-03-15

Military personnel and civilians living in areas of armed conflict have increased risk of exposure to blast overpressures that can cause significant hearing loss and/or brain injury. The equipment used to simulate comparable blast overpressures in animal models within laboratory settings is typically very large and prohibitively expensive. To overcome the fiscal and space limitations introduced by previously reported blast wave generators, we developed a compact, low-cost blast wave generator to investigate the effects of blast exposures on the auditory system and brain. The blast wave generator was constructed largely from off the shelf components, and reliably produced blasts with peak sound pressures of up to 198dB SPL (159.3kPa) that were qualitatively similar to those produced from muzzle blasts or explosions. Exposure of adult rats to 3 blasts of 188dB peak SPL (50.4kPa) resulted in significant loss of cochlear hair cells, reduced outer hair cell function and a decrease in neurogenesis in the hippocampus. Existing blast wave generators are typically large, expensive, and are not commercially available. The blast wave generator reported here provides a low-cost method of generating blast waves in a typical laboratory setting. This compact blast wave generator provides scientists with a low cost device for investigating the biological mechanisms involved in blast wave injury to the rodent cochlea and brain that may model many of the damaging effects sustained by military personnel and civilians exposed to intense blasts. Copyright © 2015 Elsevier B.V. All rights reserved.

Low-Cost Blast Wave Generator for Studies of Hearing Loss and Brain Injury: Blast Wave Effects in Closed Spaces

PubMed Central

Newman, Andrew J.; Hayes, Sarah H.; Rao, Abhiram S.; Allman, Brian L.; Manohar, Senthilvelan; Ding, Dalian; Stolzberg, Daniel; Lobarinas, Edward; Mollendorf, Joseph C.; Salvi, Richard

2015-01-01

Background Military personnel and civilians living in areas of armed conflict have increased risk of exposure to blast overpressures that can cause significant hearing loss and/or brain injury. The equipment used to simulate comparable blast overpressures in animal models within laboratory settings is typically very large and prohibitively expensive. New Method To overcome the fiscal and space limitations introduced by previously reported blast wave generators, we developed a compact, low-cost blast wave generator to investigate the effects of blast exposures on the auditory system and brain. Results The blast wave generator was constructed largely from off the shelf components, and reliably produced blasts with peak sound pressures of up to 198 dB SPL (159.3 kPa) that were qualitatively similar to those produced from muzzle blasts or explosions. Exposure of adult rats to 3 blasts of 188 dB peak SPL (50.4 kPa) resulted in significant loss of cochlear hair cells, reduced outer hair cell function and a decrease in neurogenesis in the hippocampus. Comparison to existing methods Existing blast wave generators are typically large, expensive, and are not commercially available. The blast wave generator reported here provides a low-cost method of generating blast waves in a typical laboratory setting. Conclusions This compact blast wave generator provides scientists with a low cost device for investigating the biological mechanisms involved in blast wave injury to the rodent cochlea and brain that may model many of the damaging effects sustained by military personnel and civilians exposed to intense blasts. PMID:25597910

Optical remote sensing to quantify fugitive particulate mass emissions from stationary short-term and mobile continuous sources: part II. Field applications.

PubMed

Du, Ke; Yuen, Wangki; Wang, Wei; Rood, Mark J; Varma, Ravi M; Hashmonay, Ram A; Kim, Byung J; Kemme, Michael R

2011-01-15

Quantification of emissions of fugitive particulate matter (PM) into the atmosphere from military training operations is of interest by the United States Department of Defense. A new range-resolved optical remote sensing (ORS) method was developed to quantify fugitive PM emissions from puff sources (i.e., artillery back blasts), ground-level mobile sources (i.e., movement of tracked vehicles), and elevated mobile sources (i.e., airborne helicopters) in desert areas that are prone to generating fugitive dust plumes. Real-time, in situ mass concentration profiles for PM mass with particle diameters <10 μm (PM(10)) and <2.5 μm (PM(2.5)) were obtained across the dust plumes that were generated by these activities with this new method. Back blasts caused during artillery firing were characterized as a stationary short-term puff source whose plumes typically dispersed to <10 m above the ground with durations of 10-30 s. Fugitive PM emissions caused by artillery back blasts were related to the zone charge and ranged from 51 to 463 g PM/firing for PM(10) and 9 to 176 g PM/firing for PM(2.5). Movement of tracked vehicles and flying helicopters was characterized as mobile continuous sources whose plumes typically dispersed 30-50 m above the ground with durations of 100-200 s. Fugitive PM emissions caused by moving tracked vehicles ranged from 8.3 to 72.5 kg PM/km for PM(10) and 1.1 to 17.2 kg PM/km for PM(2.5), and there was no obvious correlation between PM emission and vehicle speed. The emission factor for the helicopter flying at 3 m above the ground ranged from 14.5 to 114.1 kg PM/km for PM(10) and 5.0 to 39.5 kg PM/km for PM(2.5), depending on the velocity of the helicopter and type of soil it flies over. Fugitive PM emissions by an airborne helicopter were correlated with helicopter speed for a particular soil type. The results from this range-resolved ORS method were also compared with the data obtained with another path-integrated ORS method and a Flux Tower method.

EPR, SEM and XRD investigation of ornamental limestone and marbles from some renowned Romanian quarries.

NASA Astrophysics Data System (ADS)

Covaci, D.; Costea, C.; Dumitras, D.; Duliu, O. G.

2012-04-01

Ornamental limestone and marble samples were collected and analysed by means of Electron Paramagnetic Resonance (EPR), Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD), in order to evidence any systematic peculiarities able to be used in further provenance studies as well as to get more detailed information regarding geochemistry and mineralogy of three of the most important deposits from Romania. In this respect, 20 samples of limestone (Arnota quarry, Capatani Mountains and Mateias South quarry, Iezer Mountains) and 9 of calci-dolomitic marble (Porumbacu de Sus quarry, Fagaras Mountains) were collected over a significant sampling area. EPR spectroscopy, primarily used to asset the degree of homogeneity of considered samples, evidenced, for both Arnota and Mateias South limestone, the presence of a typical six hyperfine lines spectrum of Mn2+ ions in calcite but no traces of Fe ferromagnetic clusters. A more careful investigation has showed that although within the same quarry, there were no significant differences regarding EPR spectra, the resonance lines were systematic narrower in the case of Mateias South samples which suggested a lower content of divalent manganese ions. The Porumbacu calci-dolomitic marble, presented a more intricate Mn2+ spectrum, consisting of a superposition of typical dolomitic and calcitic spectra. Again, the EPR spectra were almost identical, attesting, as in the previous cases, a relative uniform distribution of paramagnetic Mn2+ ions within quarry. In the case of SEM, scattered, back scattered and absorbed electron modes were used to visualise the mineral formations on the sample surfaces while an EDAX quantitative analysis was used to determine the content of the most abundant elements. Although, at a first inspection, both groups of limestone looked almost similar, displaying a great variety of randomly orientated micro-crystalline agglomeration, only in the case of Arnota samples, we have noticed the presence of some micron size graphite inclusions, potential proxies for further provenance studies. The Porumbacu South marble showed a different pattern, characterized by a more uniform crystallite distribution, all of them presenting almost perfect cleaving surfaces. EDAX results evidenced, excepting the dominant Ca and Mg (the last one in the case of Porumbacu de Sus marble), the presence, in small quantities, of some other element such as Fe, Ni, Cu and Zn whose content represent also a good provenance proxy. XRD investigation evidenced not only of the dominant calcite and dolomite mineral phases, but also other minor mineral fraction, whose presence could be well related to the content of mentioned trace elements. Principal Component and Cluster Analysis, finally used to classify all investigated samples, allowed us to group them in three cluster in accordance with their provenance.

miBLAST: scalable evaluation of a batch of nucleotide sequence queries with BLAST

PubMed Central

Kim, You Jung; Boyd, Andrew; Athey, Brian D.; Patel, Jignesh M.

2005-01-01

A common task in many modern bioinformatics applications is to match a set of nucleotide query sequences against a large sequence dataset. Exis-ting tools, such as BLAST, are designed to evaluate a single query at a time and can be unacceptably slow when the number of sequences in the query set is large. In this paper, we present a new algorithm, called miBLAST, that evaluates such batch workloads efficiently. At the core, miBLAST employs a q-gram filtering and an index join for efficiently detecting similarity between the query sequences and database sequences. This set-oriented technique, which indexes both the query and the database sets, results in substantial performance improvements over existing methods. Our results show that miBLAST is significantly faster than BLAST in many cases. For example, miBLAST aligned 247 965 oligonucleotide sequences in the Affymetrix probe set against the Human UniGene in 1.26 days, compared with 27.27 days with BLAST (an improvement by a factor of 22). The relative performance of miBLAST increases for larger word sizes; however, it decreases for longer queries. miBLAST employs the familiar BLAST statistical model and output format, guaranteeing the same accuracy as BLAST and facilitating a seamless transition for existing BLAST users. PMID:16061938

H-BLAST: a fast protein sequence alignment toolkit on heterogeneous computers with GPUs.

PubMed

Ye, Weicai; Chen, Ying; Zhang, Yongdong; Xu, Yuesheng

2017-04-15

The sequence alignment is a fundamental problem in bioinformatics. BLAST is a routinely used tool for this purpose with over 118 000 citations in the past two decades. As the size of bio-sequence databases grows exponentially, the computational speed of alignment softwares must be improved. We develop the heterogeneous BLAST (H-BLAST), a fast parallel search tool for a heterogeneous computer that couples CPUs and GPUs, to accelerate BLASTX and BLASTP-basic tools of NCBI-BLAST. H-BLAST employs a locally decoupled seed-extension algorithm for better performance on GPUs, and offers a performance tuning mechanism for better efficiency among various CPUs and GPUs combinations. H-BLAST produces identical alignment results as NCBI-BLAST and its computational speed is much faster than that of NCBI-BLAST. Speedups achieved by H-BLAST over sequential NCBI-BLASTP (resp. NCBI-BLASTX) range mostly from 4 to 10 (resp. 5 to 7.2). With 2 CPU threads and 2 GPUs, H-BLAST can be faster than 16-threaded NCBI-BLASTX. Furthermore, H-BLAST is 1.5-4 times faster than GPU-BLAST. https://github.com/Yeyke/H-BLAST.git. yux06@syr.edu. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

Investigating the stratigraphy and palaeoenvironments for a suite of newly discovered mid-Cretaceous vertebrate fossil-localities in the Winton Formation, Queensland, Australia

NASA Astrophysics Data System (ADS)

Tucker, Ryan T.; Roberts, Eric M.; Darlington, Vikie; Salisbury, Steven W.

2017-08-01

The Winton Formation of central Queensland is recognized as a quintessential source of mid-Cretaceous terrestrial faunas and floras in Australia. However, sedimentological investigations linking fossil assemblages and palaeoenvironments across this unit remain limited. The intent of this study was to interpret depositional environments and improve stratigraphic correlations between multiple fossil localities within the preserved Winton Formation in the Eromanga Basin, including Isisford, Lark Quarry, and Bladensburg National Park. Twenty-three facies and six repeated facies associations were documented, indicating a mosaic of marginal marine to inland alluvial depositional environments. These developed synchronously with the final regression of the Eromanga Seaway from central Australia during the late Albian-early Turonian. Investigations of regional- and local-scale structural features and outcrop, core and well analysis were combined with detrital zircon provenance signatures to help correlate stratigraphy and vertebrate faunas across the basin. Significant palaeoenvironmental differences exist between the lower and upper portions of the preserved Winton Formation, warranting informal subdivisions; a lower tidally influenced fluvial-deltaic member and an upper inland alluvial member. This work further demonstrates that the Isisford fauna is part of the lower member of the preserved Winton Formation; whereas, fossil localities around Winton, including Lark Quarry and Bladensburg National Park, are part of the upper member of the Winton Formation. These results permit a more meaningful framework for both regional and global comparisons of the Winton flora and fauna.

Reconnaissance for radioactive materials in northeastern United States during 1952

USGS Publications Warehouse

McKeown, Francis A.; Klemic, Harry

1953-01-01

Reconnaissance for radioactive materials was made in parts of Maine, New York, New Jersey, and Pennsylvania. The primary objective was to examine the iron ore deposits and associated rocks in the Adirondack Mountains of New York and the Highlands of New Jersey. In addition, several deposits known or reported to contain radioactive minerals were examined to delimit their extent. Most of the deposits examined are not significant as possible sources of radioactive elements and the data pertaining to them are summarized in table form. Deposits that do warrant more description than can be given in table form are: Benson Mines, St. Lawrence County, N. Y.; Rutgers mine, Clinton County, N. Y.; Mineville Mines, Essex County, N. Y.l Canfield phosphate mine, Morris County, N. J.; Mullgan quarry, Hunterdon County, N. J.; and the Chestnut Hill-Marble Mountain area, Pennsylvania and New Jersey. The Old Bed in the Mineville district is the only deposit that may be economically significant. Apatite from Old Bed ore contains as much as 4.9 percent total rare earth. 0.04 percent thorium, and 0.018 percent uranium. Magnetite ore at the Rutgers mine contains radioactive zircon and apatite. Radioactivity measurements of outcrops and dump material show that the ore contains from 0.005 to 0.010 percent equivalent uranium. One sample of lean magnetite ore contains 0.006 percent equivalent uranium. Garnet-rich zones in the Benson Mines magnetite deposit contain as much as 0.017 equivalent uranium. Most of the rock and ore, however, contains about 0.005 percent equivalent uranium. Available data indicate that the garnet-rich zones are enriched in radioactive allanite. A shear zone in the Kittatinny limestone of Cambrian age at the Mulligan quarry contains uraniferous material. Radioactivity anomalies elsewhere in the quarry and in adjacent fields indicate that there may be other uraniferous shear zones. Assays of samples and measurements of outcrop radioactivity indicate that the uranium content of these zones is low; samples contain from 0.008 to 0.068 percent equivalent uranium. The anomalies, however, may indicate greater concentrations of uranium below surficial leached zones. The Chestnut Hill-Marble Mountain area contains radioactivity anomalies for about 2 miles along the strike of the contact of pre-Cambrian Pickering gneiss and Franklin limestone formations. In places this contact is injected with pegmatite, which probably was the source of the radioelements. The most favorable area for further study is at Marble Mountain, where a nearly continuous anomaly extends for about 1500 feet. Samples from part of this area contain as much as 0.044 percent equivalent uranium and 0.005 percent uranium. Radioactive hematite and florencite, in which thorium may have substituted for cerium, are the only radioactive minerals observed in the Marble Mountain area.

27 CFR 555.220 - Table of separation distances of ammonium nitrate and blasting agents from explosives or blasting...

Code of Federal Regulations, 2010 CFR

2010-04-01

... distances of ammonium nitrate and blasting agents from explosives or blasting agents. 555.220 Section 555... ammonium nitrate and blasting agents from explosives or blasting agents. Table: Department of Defense... Not over Minimum separation distance of acceptor from donor when barricaded (ft.) Ammonium nitrate...

27 CFR 555.220 - Table of separation distances of ammonium nitrate and blasting agents from explosives or blasting...

Code of Federal Regulations, 2011 CFR

2011-04-01

... distances of ammonium nitrate and blasting agents from explosives or blasting agents. 555.220 Section 555... ammonium nitrate and blasting agents from explosives or blasting agents. Table: Department of Defense... Not over Minimum separation distance of acceptor from donor when barricaded (ft.) Ammonium nitrate...

27 CFR 555.220 - Table of separation distances of ammonium nitrate and blasting agents from explosives or blasting...

Code of Federal Regulations, 2012 CFR

2012-04-01

... distances of ammonium nitrate and blasting agents from explosives or blasting agents. 555.220 Section 555... ammonium nitrate and blasting agents from explosives or blasting agents. Table: Department of Defense... Not over Minimum separation distance of acceptor from donor when barricaded (ft.) Ammonium nitrate...

27 CFR 555.220 - Table of separation distances of ammonium nitrate and blasting agents from explosives or blasting...

Code of Federal Regulations, 2013 CFR

2013-04-01

... distances of ammonium nitrate and blasting agents from explosives or blasting agents. 555.220 Section 555... ammonium nitrate and blasting agents from explosives or blasting agents. Table: Department of Defense... Not over Minimum separation distance of acceptor from donor when barricaded (ft.) Ammonium nitrate...

27 CFR 555.220 - Table of separation distances of ammonium nitrate and blasting agents from explosives or blasting...

Code of Federal Regulations, 2014 CFR

2014-04-01

... distances of ammonium nitrate and blasting agents from explosives or blasting agents. 555.220 Section 555... ammonium nitrate and blasting agents from explosives or blasting agents. Table: Department of Defense... Not over Minimum separation distance of acceptor from donor when barricaded (ft.) Ammonium nitrate...

High-fidelity simulations of blast loadings in urban environments using an overset meshing strategy

NASA Astrophysics Data System (ADS)

Wang, X.; Remotigue, M.; Arnoldus, Q.; Janus, M.; Luke, E.; Thompson, D.; Weed, R.; Bessette, G.

2017-05-01

Detailed blast propagation and evolution through multiple structures representing an urban environment were simulated using the code Loci/BLAST, which employs an overset meshing strategy. The use of overset meshes simplifies mesh generation by allowing meshes for individual component geometries to be generated independently. Detailed blast propagation and evolution through multiple structures, wave reflection and interaction between structures, and blast loadings on structures were simulated and analyzed. Predicted results showed good agreement with experimental data generated by the US Army Engineer Research and Development Center. Loci/BLAST results were also found to compare favorably to simulations obtained using the Second-Order Hydrodynamic Automatic Mesh Refinement Code (SHAMRC). The results obtained demonstrated that blast reflections in an urban setting significantly increased the blast loads on adjacent buildings. Correlations of computational results with experimental data yielded valuable insights into the physics of blast propagation, reflection, and interaction under an urban setting and verified the use of Loci/BLAST as a viable tool for urban blast analysis.

Linking blast physics to biological outcomes in mild traumatic brain injury: Narrative review and preliminary report of an open-field blast model.

PubMed

Song, Hailong; Cui, Jiankun; Simonyi, Agnes; Johnson, Catherine E; Hubler, Graham K; DePalma, Ralph G; Gu, Zezong

2018-03-15

Blast exposures are associated with traumatic brain injury (TBI) and blast-induced TBIs are common injuries affecting military personnel. Department of Defense and Veterans Administration (DoD/VA) reports for TBI indicated that the vast majority (82.3%) has been mild TBI (mTBI)/concussion. mTBI and associated posttraumatic stress disorders (PTSD) have been called "the invisible injury" of the current conflicts in Iraq and Afghanistan. These injuries induce varying degrees of neuropathological alterations and, in some cases, chronic cognitive, behavioral and neurological disorders. Appropriate animal models of blast-induced TBI will not only assist the understanding of physical characteristics of the blast, but also help to address the potential mechanisms. This report provides a brief overview of physical principles of blast, injury mechanisms related to blast exposure, current blast animal models, and the neurological behavioral and neuropathological findings related to blast injury in experimental settings. We describe relationships between blast peak pressures and the observed injuries. We also report preliminary use of a highly reproducible and intensity-graded blast murine model carried out in open-field with explosives, and describe physical and pathological findings in this experimental model. Our results indicate close relationships between blast intensities and neuropathology and behavioral deficits, particularly at low level blast intensities relevant to mTBI. Copyright © 2016 Elsevier B.V. All rights reserved.

The region of the Piedra Berroqueña: A potencial Global Heritage Stone Province.

NASA Astrophysics Data System (ADS)

Freire-Lista, David Martin; Fort, Rafael

2015-04-01

The Piedra Berroqueña region occupies an area of approximately 4000 km2 in the Sierra de Guadarrama, Spanish Central System, the centre of the Iberian Peninsula. This region has provided most of the building granites used in Madrid and surrounding provinces. Traditional methods of cutting and carving stone have been preserved and it is easy to locate historic quarries in its landscape in addition to mechanized quarries with large reserves of this dimension stone that is exported worldwide in the form of blocks or slabs with different finishes. The Piedra Berroqueña has been used as a building stone since before the Romans. Petrophysical and durability characteristics have allowed to endure monuments as representative as The Royal Monastery of San Lorenzo del Escorial (1563-1584), del Sol Gate (1857-1862), Royal Palace (1738-1764), Alcalá Gate (1770-1778) or Prado Museum (1785-1808) in Madrid, Spain. Also the Piedra Berroqueña is part of most residential buildings and streets of this city, as well as modern buildings around the world, such as airport terminals in Athens, Cork, the British consulate in Hong Kong and headquarters of banks in Jakarta, among others. Piedra Berroqueña province is presented in this abstract, which has many granite quarries with common characteristics such as their grey tones and the presence of darker enclaves "Gabarros or negrones". In the Piedra Berroqueña province four main types of granite can be distinguish: Peraluminous granites; with biotite and occasional cordierite, whose most representative historic quarries are in Alpedrete, Colmenar Viejo, El Boalo, El Berrocal and Collado Mediano. Biotite granites with occasional amphibole are present in historic quarries in El Berrueco, Lozoyuela-Navas-Sieteiglesias and Pelayo de la Presa, among others. Currently exploited in Valdemanco and La Cabrera and marketed under the commercial names of Aurora Blanco, Blanco Berrocal, Crema Champagne, Blanco Castilla, Crema Cabrera, Blanco Perla, Crema Valdemanco. In Cadalso de los Vidrios it is marketed under the commercial name of Gris Cadalso and Rosa Cadalso. Biotite granites without cordierite or amphibole and the most representative historic quarries are in San Lorenzo del Escorial, Valdemorillo, Robledo de Chavela, Colmenar de Arroyo, Chapinería and Navas del Rey. In Zarzalejo is marketed under the commercial name of Gris Escorial. Leucogranites in Manzanares el Real, San Martín de Valdeiglesias or La Cabrera there are historical quarries. In the Cadalso de los Vidrios is exported under the commercial name Blanco Ártico, Blanco Cristal and Oro Cristal. The Piedra Berroqueña province meets the requirements proposed to be nominated for GHSP. This nomination will contribute to better understanding and dissemination of an area with attractive economic aspects that focuses on the use of its resources. Thus, the Piedra Berroqueña remains part of the heritage of the province, whether used as a replacement stone for restoration of heritage buildings or when used for new buildings. Acknowledgements This study was funded by the Community of Madrid under the GEOMATERIALS 2 project (S2013/MIT-2914). The authors are members of the Complutense University of Madrid's Research Group: "Alteración y Conservación de los Materiales Pétreos del Patrimonio" (ref. 921349).

Transport and deposition processes of the hydrothermal blast of the 6 August 2012 Te Maari eruption, Mt. Tongariro

NASA Astrophysics Data System (ADS)

Breard, E. C. P.; Lube, G.; Cronin, S. J.; Valentine, G. A.

2015-11-01

The 2012 eruption of Tongariro volcano (New Zealand) produced highly mobile, low-temperature, blast-derived pyroclastic density currents after partial collapse of the western flank of the Upper Te Maari crater. Despite a low volume (340,000 m3), the flows traveled up to 2.5 km from source, covering a total area of 6.1 km2. Along one of the blast axes, freshly exposed, proximal-to-distal sedimentary structures and grain-size data suggest emplacement of the fining upward tripartite depositional sequence (massive, stratified, and laminated) under a dilute and strongly longitudinally zoned turbulent density current. While the zoning formed in the deposit in the first 1500 m of runout, the current progressively waned to the extent where it transported a nearly homogenous grain-size mixture at the liftoff position. Our data indicate that after the passage of an erosive flow front, massive unit A was deposited under a rapid-suspension sedimentation regime. Unit B was deposited under a traction-dominated regime generated by a subsequent portion of the flow moving at lower velocities and with lower sediment transport capacity than the portion depositing unit A. The final and slowest flow zone deposited the finest particles under weakly tractive conditions. Transport and emplacement dynamics inferred in this study show strong similarities between hydrothermal explosions, magmatic blasts, and high-energy dilute PDCs. The common occurrence of hydrothermal fields on volcanic flanks points to this hazard being an under-appreciated one at stratovolcanoes worldwide.

Iron and Sulfur Geochemistry in Serpentinizing Groundwaters: Relationships to Microbiological Processes

NASA Astrophysics Data System (ADS)

Sabuda, M.; Kubo, M. D.; Cardace, D.; Hoehler, T. M.; McCollom, T. M.; Schrenk, M. O.

2016-12-01

Serpentinization of ultramafic rock in ophiolite complexes along continental margins leads to the mobilization of volatiles and reduced carbon compounds that can be used as sources of nutrients and energy by subsurface microbial communities. Simultaneously, the highly reducing character of serpentinite-associated fluids can lead to limitations in the availability of oxidants to support growth. The extent to which iron and sulfur compounds can serve as alternative electron acceptors in serpentinizing systems remains to be elucidated. Heterogeneous mineralogy, meteoric and groundwater source mixing, ancient marine sediment influence, and microbial metabolic activities likely contribute to variability in the identity and abundance of Fe and S compounds in serpentinite groundwater. At the Coast Range Ophiolite Microbial Observatory (CROMO) in northern California, the aqueous geochemistry of sulfur and iron in the alkaline groundwater was investigated at multiple time points taken from 12 wells located in two clusters, Core Shed and Quarry Valley, with individual boreholes sampling different depths. Colorimetric methods (HS-, ferrous and total iron), ion chromatography (SO42-), and ICP-MS (total Fe and S) were utilized and on average, both sulfate and sulfide are highest in the CSW wells (300 μM and 15 μM respectively), and lowest in the N08 wells (95 μM, 1.2 μM) within the Quarry Valley area. Ferrous iron measured <0.7 μM in all boreholes, likely due to the poor solubility of dissolved iron at high pH. Bioenergetic calculations were generated using CROMO geochemical data to investigate the favorability of various Fe and S red-ox reactions. Additionally, the presence of key genes in sulfur and iron metabolic pathways was examined in metagenomic assemblies from CROMO. Combined, these data reinforce the critical role that sulfur-associated metabolisms, in particular, play in serpentinite groundwater. Consequently, the sulfur biogeochemistry of such systems may influence geochemical cycles and ultimately be preserved in the rock record.

Determination of respirable-sized crystalline silica in different ambient environments in the United Kingdom with a mobile high flow rate sampler utilising porous foams to achieve the required particle size selection

NASA Astrophysics Data System (ADS)

Stacey, Peter; Thorpe, Andrew; Roberts, Paul; Butler, Owen

2018-06-01

Inhalation of respirable crystalline silica (RCS) can cause diseases including silicosis and cancer. Levels of RCS close to an emission source are measured but little is known about the wider ambient exposure from industry emissions or natural sources. The aim of this work is to report the RCS concentrations obtained from a variety of ambient environments using a new mobile respirable (PM4) sampler. A mobile battery powered high flow rate (52 L min-1) sampler was developed and evaluated for particulate aerosol sampling employing foams to select the respirable particle size fraction. Sampling was conducted in the United Kingdom at site boundaries surrounding seven urban construction and demolition and five sand quarry sites. These are compared with data from twelve urban aerosol samples and from repeat measurements from a base line study at a single rural site. The 50% particle size penetration (d50) through the foam was 4.3 μm. Over 85% of predict bias values were with ±10% of the respirable convention, which is based on a log normal curve. Results for RCS from all construction and quarry activities are generally low with a 95 th percentile of 11 μg m-3. Eighty percent of results were less than the health benchmark value of 3 μg m-3 used in some states in America for ambient concentrations. The power cutting of brick and the largest demolition activities gave the highest construction levels. Measured urban background RCS levels were typically below 0.3 μg m-3 and the median RCS level, at a rural background location, was 0.02 μg m-3. These reported ambient RCS concentrations may provide useful baseline values to assess the wider impact of fugitive, RCS containing, dust emissions into the wider environment.

The impact of human activities on the natural geoheritage and its effects on geodiversity. The case of the Italian karst areas.

NASA Astrophysics Data System (ADS)

Laureti, Lamberto

2017-04-01

In Italy the karst environments represent nearly half of the mountainous areas, with typical aspects characterized by a strong articulation of the relief, often induced by recent tectonic evolution, with closed depressions and plateaus, steep slopes, sharp interface soil-rocks and soil sediments inside the fissures and rock cavities. From the middle Holocene the human impact in the italian karst areas cleared the original extensive sclerophyllous forests in order to utilize space for grazing and agriculture, but favoured in this way the erosion of the soil cover and, in time, caused a nearly complete desertification of many mountain slopes. The forms of impact were and are represented by slope terracing for intensive agriculture, large use of fertilizer and pesticides, stocking of bio-masses of cattle, pigs and chickens in small areas, opening of quarries and mines, besides other interventions. Among all the forms of human impact, the mining and quarrying activities are responsible of high deterioration of the karst environment as a consequence of great rocks excavations and movements, together with metal polluted waters leaking. After the closure and the abandonment of the nearly all Italian metal mines, especially in Sardinia but also in the Alpine ore districts, the quarries excavation is really the main threat towards the Italian karst areas, because of the increase of the stony materials international market. By this regard, in this poster are showed the case studies referring to the Lombard Prealpine karst plateaus (where many interesting caves were destroyed) and to the karst systems of the Apuane Alps (Tuscany), where the quarries of the famous "Carrara marble" endangered the same great "Antro di Corchia", today preserved by the creation of a natural park.

Experimental study on the strength parameter of Quarry Dust mixed Coconut Shell Concrete adding Coconut Fibre

NASA Astrophysics Data System (ADS)

Matangulu Shrestha, Victor; Anandh, S.; Sindhu Nachiar, S.

2017-07-01

Concrete is a heterogeneous mixture constitute of cement as the main ingredient with a different mix of fine and coarse aggregate. The massive use of conventional concrete has a shortfall in its key ingredients, natural sand and coarse aggregate, due to increased industrialisation and globalisation. To overcome the shortage of material, an alternate material with similar mechanical properties and composition has to be studied, as replacement of conventional concrete. Coconut shell concrete is a prime option as replacement of key ingredients of conventional concrete as coconut is produced in massive quantity in south East Asia. Coconut shell concrete is lightweight concrete and different research is still ongoing concerning about its mix design and composition in the construction industry. Concrete is weak in tension as compared to compression, hence the fibre is used to refrain the crack in the concrete. Coconut fibre is one of many fibres which can be used in concrete. The main aim of this project is to analyse the use of natural by-products in the construction industry, make light weight concrete and eco-friendly construction. This project concerns with the comparison of the mechanical properties of coconut shell concrete and conventional concrete, replacing fine aggregate with quarry dust using coconut fibre. M25 grade of concrete was adopted and testing of concrete was done at the age of 3, 7 and 28 days. In this concrete mix, sand was replaced completely in volumetric measurement by quarry dust. The result was analysed and compared with addition of coconut fibre at varying percentage of 1%, 2%, 3%, 4% and 5%. From the test conducted, coconut shell concrete with quarry dust has the maximum value at 4% of coconut fibre while conventional concrete showed the maximum value at 2% of coconut fibre.

Assessment of occupational exposure in a granite quarry and processing factory.

PubMed

Tejado, J J; Guillén, J; Baeza, A

2016-09-01

Workers in the granite industry face an occupational hazard: silicosis due to the crystalline silica present in inhalable dust. As granite can also present a variable, and occasionally significant, content of naturally occurring radionuclides, they may also face a radiological hazard. In order to assess the risk, a granite industry with a quarry and processing factory was selected to assess the occupational exposure. Three main potential pathways were observed: external irradiation, inhalation of granite dust, and radon exposure. The external dose rate was similar to that in a nearby farming area. A slight increment (0.016-0.076 mSv yr -1 ) was observed in the quarry and stockpile, due to quarry faces and granite blocks. The effective dose due to granite dust inhalation was 0.182  ±  0.009 mSv yr -1 in the worst case scenario (3 mg m -3 dust load in air and no use of filter masks). Thus, the mean value of the effective dose from these two pathways was 0.26 mSv yr -1 , lower than the reference level of 1 mSv yr -1 for the general population. The annual mean value of radon concentration in the indoor air was 33 Bq m -3 . However, during granite processing works the radon concentration can increase up to 216 Bq m -3 , due to mechanical operations (sawing, polishing, sanding, etc). This radon concentration was below the 600 Bq m -3 reference level for action in working places. Therefore, workers in this granite factory face no significant additional radiological exposure, and no-one needs to be designated as occupationally exposed and subject to individual dosimetry.

Archaeological investigations on the Buckboard Mesa Road Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Amick, D.S.; Henton, G.H.; Pippin, L.C.

1991-10-01

In 1986, the Desert Research Institute (DRI) conducted an archaeological reconnaissance of a new alignment for the Buckboard Mesa Road on the Nevada Test Site for the Department of Energy (DOE). During this reconnaissance, several archaeological sites of National Register quality were discovered and recorded including a large quarry, site 26Ny4892, and a smaller lithic scatter, site 26Ny4894. Analysis of the debitage at 26Ny4892 indicates that this area was used primarily as a quarry for relatively small cobbles of obsidian found in the alluvium. Lithic reduction techniques used here are designed for efficiently reducing small pieces of toolstone and aremore » oriented towards producing flake blanks from small cores and bifacially reducing exhausted cores. Projectile point cross references indicate that the area has seen at least casual use for about 10,000 years and more sustained use for the last 3,000 years. Initial obsidian hydration measurements indicate sustained use of the quarry for about the last 3,000 years although the loci of activities appear to change over time. Based on this study, the DRI recommends that quarrying activities in the area of 26Ny4892 are sufficiently sampled and that additional investigations into that aspect of prehistoric activity in the area are not necessary. This does not apply to other aspects of prehistoric use. DRI recommends that preconstruction surveys continue to identify nonquarrying, prehistoric utilization of the area. With the increased traffic on the Buckboard Mesa Road, there is a greater potential for vandalism to sites of National Register-quality located near the road. The DRI recommends that during the orientation briefing the workers at the Test Site be educated about the importance of cultural resources and the need for their protection. 202 refs., 41 figs., 52 tabs.« less

Blasting for abandoned-mine land reclamation (closure of individual subsidence features and erratic, undocumented underground coal-mine workings). Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Workman, J.L.; Thompson, J.

1991-01-01

The study has examined the feasibility of blasting for mitigating various abandoned mine land features on AML sites. The investigation included extensive field trial blasts at sites in North Dakota and Montana. A blasting technique was used that was based on spherical cratering concepts. At the Beulah, North Dakota site thirteen individual vertical openings (sinkholes) were blasted with the intent to fill the voids. The blasts were designed to displace material laterally into the void. Good success was had in filling the sinkholes. At the White site in Montana erratic underground rooms with no available documentation were collapsed. An aditmore » leading into the mine was also blasted. Both individual room blasting and area pattern blasting were studied. A total of eight blasts were fired on the one acre area. Exploration requirements and costs were found to be extensive.« less

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

Microfabrication of microchannels for fuel cell plates.

PubMed

Jang, Ho Su; Park, Dong Sam

2010-01-01

Portable electronic devices such as notebook computers, PDAs, cellular phones, etc., are being widely used, and they increasingly need cheap, efficient, and lightweight power sources. Fuel cells have been proposed as possible power sources to address issues that involve energy production and the environment. In particular, a small type of fuel-cell system is known to be suitable for portable electronic devices. The development of micro fuel cell systems can be achieved by the application of microchannel technology. In this study, the conventional method of chemical etching and the mechanical machining method of micro end milling were used for the microfabrication of microchannel for fuel cell separators. The two methods were compared in terms of their performance in the fabrication with regards to dimensional errors, flatness, straightness, and surface roughness. Following microchannel fabrication, the powder blasting technique is introduced to improve the coating performance of the catalyst on the surface of the microchannel. Experimental results show that end milling can remarkably increase the fabrication performance and that surface treatment by powder blasting can improve the performance of catalyst coating.

Microfabrication of Microchannels for Fuel Cell Plates

PubMed Central

Jang, Ho Su; Park, Dong Sam

2010-01-01

Portable electronic devices such as notebook computers, PDAs, cellular phones, etc., are being widely used, and they increasingly need cheap, efficient, and lightweight power sources. Fuel cells have been proposed as possible power sources to address issues that involve energy production and the environment. In particular, a small type of fuel-cell system is known to be suitable for portable electronic devices. The development of micro fuel cell systems can be achieved by the application of microchannel technology. In this study, the conventional method of chemical etching and the mechanical machining method of micro end milling were used for the microfabrication of microchannel for fuel cell separators. The two methods were compared in terms of their performance in the fabrication with regards to dimensional errors, flatness, straightness, and surface roughness. Following microchannel fabrication, the powder blasting technique is introduced to improve the coating performance of the catalyst on the surface of the microchannel. Experimental results show that end milling can remarkably increase the fabrication performance and that surface treatment by powder blasting can improve the performance of catalyst coating. PMID:22315533

Radiological-Pathological Correlations Following Blast-Related Traumatic Brain Injury in the Whole Human Brain Using ex Vivo Diffusion Tensor Imaging

DTIC Science & Technology

2014-01-01

were as follows: Blast TBI: Suicide drug overdose – blast years prior Ruptured aneurysm – blast years prior intraventricular hemorrhage...drug overdose Suicide blunt trauma - fall Cancer Cardiac Arrest Tissue fixation was highly variable because cases were obtained from 4 different...blast years prior Civilian Blast DOA Non-blast TBI: MVA – DOA MVA – DOS Suicide – NFL – GSW to chest Cardiac Arrest – NFL Controls: Suicide

SS-Wrapper: a package of wrapper applications for similarity searches on Linux clusters.

PubMed

Wang, Chunlin; Lefkowitz, Elliot J

2004-10-28

Large-scale sequence comparison is a powerful tool for biological inference in modern molecular biology. Comparing new sequences to those in annotated databases is a useful source of functional and structural information about these sequences. Using software such as the basic local alignment search tool (BLAST) or HMMPFAM to identify statistically significant matches between newly sequenced segments of genetic material and those in databases is an important task for most molecular biologists. Searching algorithms are intrinsically slow and data-intensive, especially in light of the rapid growth of biological sequence databases due to the emergence of high throughput DNA sequencing techniques. Thus, traditional bioinformatics tools are impractical on PCs and even on dedicated UNIX servers. To take advantage of larger databases and more reliable methods, high performance computation becomes necessary. We describe the implementation of SS-Wrapper (Similarity Search Wrapper), a package of wrapper applications that can parallelize similarity search applications on a Linux cluster. Our wrapper utilizes a query segmentation-search (QS-search) approach to parallelize sequence database search applications. It takes into consideration load balancing between each node on the cluster to maximize resource usage. QS-search is designed to wrap many different search tools, such as BLAST and HMMPFAM using the same interface. This implementation does not alter the original program, so newly obtained programs and program updates should be accommodated easily. Benchmark experiments using QS-search to optimize BLAST and HMMPFAM showed that QS-search accelerated the performance of these programs almost linearly in proportion to the number of CPUs used. We have also implemented a wrapper that utilizes a database segmentation approach (DS-BLAST) that provides a complementary solution for BLAST searches when the database is too large to fit into the memory of a single node. Used together, QS-search and DS-BLAST provide a flexible solution to adapt sequential similarity searching applications in high performance computing environments. Their ease of use and their ability to wrap a variety of database search programs provide an analytical architecture to assist both the seasoned bioinformaticist and the wet-bench biologist.

SS-Wrapper: a package of wrapper applications for similarity searches on Linux clusters

PubMed Central

Wang, Chunlin; Lefkowitz, Elliot J

2004-01-01

Background Large-scale sequence comparison is a powerful tool for biological inference in modern molecular biology. Comparing new sequences to those in annotated databases is a useful source of functional and structural information about these sequences. Using software such as the basic local alignment search tool (BLAST) or HMMPFAM to identify statistically significant matches between newly sequenced segments of genetic material and those in databases is an important task for most molecular biologists. Searching algorithms are intrinsically slow and data-intensive, especially in light of the rapid growth of biological sequence databases due to the emergence of high throughput DNA sequencing techniques. Thus, traditional bioinformatics tools are impractical on PCs and even on dedicated UNIX servers. To take advantage of larger databases and more reliable methods, high performance computation becomes necessary. Results We describe the implementation of SS-Wrapper (Similarity Search Wrapper), a package of wrapper applications that can parallelize similarity search applications on a Linux cluster. Our wrapper utilizes a query segmentation-search (QS-search) approach to parallelize sequence database search applications. It takes into consideration load balancing between each node on the cluster to maximize resource usage. QS-search is designed to wrap many different search tools, such as BLAST and HMMPFAM using the same interface. This implementation does not alter the original program, so newly obtained programs and program updates should be accommodated easily. Benchmark experiments using QS-search to optimize BLAST and HMMPFAM showed that QS-search accelerated the performance of these programs almost linearly in proportion to the number of CPUs used. We have also implemented a wrapper that utilizes a database segmentation approach (DS-BLAST) that provides a complementary solution for BLAST searches when the database is too large to fit into the memory of a single node. Conclusions Used together, QS-search and DS-BLAST provide a flexible solution to adapt sequential similarity searching applications in high performance computing environments. Their ease of use and their ability to wrap a variety of database search programs provide an analytical architecture to assist both the seasoned bioinformaticist and the wet-bench biologist. PMID:15511296

PAIR-DOMINATED GeV-OPTICAL FLASH IN GRB 130427A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vurm, Indrek; Hascoët, Romain; Beloborodov, Andrei M., E-mail: indrek.vurm@gmail.com

2014-07-10

We show that the light curve of the double GeV+optical flash in GRB 130427A is consistent with radiation from the blast wave in a wind-type medium with density parameter A = ρr {sup 2} ∼ 5 × 10{sup 10} g cm{sup –1}. The peak of the flash is emitted by copious e {sup ±} pairs created and heated in the blast wave; our first-principle calculation determines the pair-loading factor and temperature of the shocked plasma. Using detailed radiative transfer simulations, we reconstruct the observed double flash. The optical flash is dominated by synchrotron emission from the thermal plasma behind the forward shock, andmore » the GeV flash is produced via inverse Compton (IC) scattering by the same plasma. The seed photons for IC scattering are dominated by the prompt MeV radiation during the first tens of seconds, and by the optical to X-ray afterglow thereafter. IC cooling of the thermal plasma behind the forward shock reproduces all GeV data from a few seconds to ∼1 day. We find that the blast wave Lorentz factor at the peak of the flash is Γ ≈ 200, and the forward shock magnetization is ε{sub B} ∼ 2 × 10{sup –4}. An additional source is required by the data in the optical and X-ray bands at times >10{sup 2} s; we speculate that this additional source may be a long-lived reverse shock in the explosion ejecta.« less

Chronic Traumatic Encephalopathy in Blast-Exposed Military Veterans and a Blast Neurotrauma Mouse Model

PubMed Central

Goldstein, Lee E.; Fisher, Andrew M.; Tagge, Chad A.; Zhang, Xiao-Lei; Velisek, Libor; Sullivan, John A.; Upreti, Chirag; Kracht, Jonathan M.; Ericsson, Maria; Wojnarowicz, Mark W.; Goletiani, Cezar J.; Maglakelidze, Giorgi M.; Casey, Noel; Moncaster, Juliet A.; Minaeva, Olga; Moir, Robert D.; Nowinski, Christopher J.; Stern, Robert A.; Cantu, Robert C.; Geiling, James; Blusztajn, Jan K.; Wolozin, Benjamin L.; Ikezu, Tsuneya; Stein, Thor D.; Budson, Andrew E.; Kowall, Neil W.; Chargin, David; Sharon, Andre; Saman, Sudad; Hall, Garth F.; Moss, William C.; Cleveland, Robin O.; Tanzi, Rudolph E.; Stanton, Patric K.; McKee, Ann C.

2013-01-01

Blast exposure is associated with traumatic brain injury (TBI), neuropsychiatric symptoms, and long-term cognitive disability. We examined a case series of postmortem brains from U.S. military veterans exposed to blast and/or concussive injury. We found evidence of chronic traumatic encephalopathy (CTE), a tau protein–linked neurodegenerative disease, that was similar to the CTE neuropathology observed in young amateur American football players and a professional wrestler with histories of concussive injuries. We developed a blast neurotrauma mouse model that recapitulated CTE-linked neuropathology in wild-type C57BL/6 mice 2 weeks after exposure to a single blast. Blast-exposed mice demonstrated phosphorylated tauopathy, myelinated axonopathy, microvasculopathy, chronic neuroinflammation, and neurodegeneration in the absence of macroscopic tissue damage or hemorrhage. Blast exposure induced persistent hippocampal-dependent learning and memory deficits that persisted for at least 1 month and correlated with impaired axonal conduction and defective activity-dependent long-term potentiation of synaptic transmission. Intracerebral pressure recordings demonstrated that shock waves traversed the mouse brain with minimal change and without thoracic contributions. Kinematic analysis revealed blast-induced head oscillation at accelerations sufficient to cause brain injury. Head immobilization during blast exposure prevented blast-induced learning and memory deficits. The contribution of blast wind to injurious head acceleration may be a primary injury mechanism leading to blast-related TBI and CTE. These results identify common pathogenic determinants leading to CTE in blast-exposed military veterans and head-injured athletes and additionally provide mechanistic evidence linking blast exposure to persistent impairments in neurophysiological function, learning, and memory. PMID:22593173

Chronic traumatic encephalopathy in blast-exposed military veterans and a blast neurotrauma mouse model.

PubMed

Goldstein, Lee E; Fisher, Andrew M; Tagge, Chad A; Zhang, Xiao-Lei; Velisek, Libor; Sullivan, John A; Upreti, Chirag; Kracht, Jonathan M; Ericsson, Maria; Wojnarowicz, Mark W; Goletiani, Cezar J; Maglakelidze, Giorgi M; Casey, Noel; Moncaster, Juliet A; Minaeva, Olga; Moir, Robert D; Nowinski, Christopher J; Stern, Robert A; Cantu, Robert C; Geiling, James; Blusztajn, Jan K; Wolozin, Benjamin L; Ikezu, Tsuneya; Stein, Thor D; Budson, Andrew E; Kowall, Neil W; Chargin, David; Sharon, Andre; Saman, Sudad; Hall, Garth F; Moss, William C; Cleveland, Robin O; Tanzi, Rudolph E; Stanton, Patric K; McKee, Ann C

2012-05-16

Blast exposure is associated with traumatic brain injury (TBI), neuropsychiatric symptoms, and long-term cognitive disability. We examined a case series of postmortem brains from U.S. military veterans exposed to blast and/or concussive injury. We found evidence of chronic traumatic encephalopathy (CTE), a tau protein-linked neurodegenerative disease, that was similar to the CTE neuropathology observed in young amateur American football players and a professional wrestler with histories of concussive injuries. We developed a blast neurotrauma mouse model that recapitulated CTE-linked neuropathology in wild-type C57BL/6 mice 2 weeks after exposure to a single blast. Blast-exposed mice demonstrated phosphorylated tauopathy, myelinated axonopathy, microvasculopathy, chronic neuroinflammation, and neurodegeneration in the absence of macroscopic tissue damage or hemorrhage. Blast exposure induced persistent hippocampal-dependent learning and memory deficits that persisted for at least 1 month and correlated with impaired axonal conduction and defective activity-dependent long-term potentiation of synaptic transmission. Intracerebral pressure recordings demonstrated that shock waves traversed the mouse brain with minimal change and without thoracic contributions. Kinematic analysis revealed blast-induced head oscillation at accelerations sufficient to cause brain injury. Head immobilization during blast exposure prevented blast-induced learning and memory deficits. The contribution of blast wind to injurious head acceleration may be a primary injury mechanism leading to blast-related TBI and CTE. These results identify common pathogenic determinants leading to CTE in blast-exposed military veterans and head-injured athletes and additionally provide mechanistic evidence linking blast exposure to persistent impairments in neurophysiological function, learning, and memory.

Forensic analysis of explosives using isotope ratio mass spectrometry (IRMS)--discrimination of ammonium nitrate sources.

PubMed

Benson, Sarah J; Lennard, Christopher J; Maynard, Philip; Hill, David M; Andrew, Anita S; Roux, Claude

2009-06-01

An evaluation was undertaken to determine if isotope ratio mass spectrometry (IRMS) could assist in the investigation of complex forensic cases by providing a level of discrimination not achievable utilising traditional forensic techniques. The focus of the research was on ammonium nitrate (AN), a common oxidiser used in improvised explosive mixtures. The potential value of IRMS to attribute Australian AN samples to the manufacturing source was demonstrated through the development of a preliminary AN classification scheme based on nitrogen isotopes. Although the discrimination utilising nitrogen isotopes alone was limited and only relevant to samples from the three Australian manufacturers during the evaluated time period, the classification scheme has potential as an investigative aid. Combining oxygen and hydrogen stable isotope values permitted the differentiation of AN prills from three different Australian manufacturers. Samples from five different overseas sources could be differentiated utilising a combination of the nitrogen, oxygen and hydrogen isotope values. Limited differentiation between Australian and overseas prills was achieved for the samples analysed. The comparison of nitrogen isotope values from intact AN prill samples with those from post-blast AN prill residues highlighted that the nitrogen isotopic composition of the prills was not maintained post-blast; hence, limiting the technique to analysis of un-reacted explosive material.

On the Propagation and Interaction of Spherical Blast Waves

NASA Technical Reports Server (NTRS)

Kandula, Max; Freeman, Robert

2007-01-01

The characteristics and the scaling laws of isolated spherical blast waves have been briefly reviewed. Both self-similar solutions and numerical solutions of isolated blast waves are discussed. Blast profiles in the near-field (strong shock region) and the far-field (weak shock region) are examined. Particular attention is directed at the blast overpressure and shock propagating speed. Consideration is also given to the interaction of spherical blast waves. Test data for the propagation and interaction of spherical blast waves emanating from explosives placed in the vicinity of a solid propellant stack are presented. These data are discussed with regard to the scaling laws concerning the decay of blast overpressure.