Flexible chitosan-nano ZnO antimicrobial pouches as a new material for extending the shelf life of raw meat.

PubMed

Rahman, P Mujeeb; Mujeeb, V M Abdul; Muraleedharan, K

2017-04-01

As a breakthrough to open up the industrial use of novel environmentally benign packaging material, we propose the first report on portable chitosan-ZnO nano-composite pouches that will serve as elite entrants in smart packaging. A facile, one pot procedure was adopted for the preparation of the C-ZnC films. In order to tune the property of C-ZnC films, four different composite films were prepared by varying the concentration of ZnO. The prepared films were found to be much superior when compared to bare chitosan and other conventional films. Two bacterial strains that commonly contaminate in packed meat were selected as target microbes to elucidate the antimicrobial activity of the prepared C-ZnO film. Detailed investigations revealed that the antimicrobial efficiency is linearly related to the amount of ZnO nano-particles in the composite. The C-2 films exhibited excellent antimicrobial activity and was fabricated into packaging pouches for raw meat. The prepared pouches showed significant action against the microbes in raw meat owing to its complete inhibition of microbial growth on the sixth day of storage at 4°C. The C-2 pouches stand as a top-notch material when compared to polyethylene bag in extending the shelf life of raw meat. Copyright © 2017 Elsevier B.V. All rights reserved.

Development of an Assessment Method for Building Materials Under Euratom Scope.

PubMed

de With, Govert

2017-11-01

In 2013, the European Commission published its basic safety standards for protection against the dangers arising from exposure to ionizing radiation (Council Directive 2013/59/Euratom)-also known as EU-BSS. As a result, the use of raw materials with potentially elevated activity concentrations such as fly ash, phosphogypsum, and slags will now fall under EU-BSS scope when applied in building materials. In light of this new policy, a variety of tools are available to assess compliance with the 1-mSv y reference level for building materials. At the heart of these tools is a gamma-spectrometric determination of the naturally occurring radionuclides Ra, Th, and K in the material of concern. As a large number of construction products contain a certain amount of the raw material that falls under the scope of the EU regulation, this policy will lead to substantial measurement of building materials that pose little radiation risk. For this reason, a method is developed to enable assessment against the 1-mSv value not on the basis of gamma-spectrometric analysis but rather based on the product's material composition. The proposed method prescribes a maximum permitted content of raw materials with potentially elevated activity concentrations in terms of a weight percentage of the end product, where the raw materials of concern are defined as those listed in Annex XIII of the EU-BSS. The permitted content is a function of the product's surface density. Therefore, a product with a low surface density of up to 25 kg m can consist of nearly 100% raw materials with potentially elevated activity concentrations, and this percentage drops to around 15% for products with a surface density of around 500 kg m. Building materials that comply with these requirements on product composition are exempt from testing, while products that do not comply must perform regular gamma-spectrometric analysis. A full validation and testing of the method is provided. In addition, the paper discusses issues relevant for regulatory implementation.

Influence of boiling point range of feedstock on properties of derived mesophase pitch

NASA Astrophysics Data System (ADS)

Yu, Ran; Liu, Dong; Lou, Bin; Chen, Qingtai; Zhang, Yadong; Li, Zhiheng

2018-06-01

The composition of raw material was optimized by vacuum distillation. The carbonization behavior of two kinds of raw material was followed by polarizing microscope, softening point, carbon yield and solubility. Two kinds of mesophase pitch have been monitored by X-ray diffraction (XRD), Fourier transform infrared spectrometer (FTIR), elemental analysis and 1H nuclear magnetic resonance (1H-NMR). The analysis results suggested that raw material B (15wt% of A was distillated out and the residue named B) could form large domain mesophase pitch earlier. The shortened heat treat time favored the retaining of alkyl group in mesophase pitch and reduced the softening point of masophase pitch.

Theoretical backgrounds of non-tempered materials production based on new raw materials

NASA Astrophysics Data System (ADS)

Lesovik, V. S.; Volodchenko, A. A.; Glagolev, E. S.; Chernysheva, N. V.; Lashina, I. V.; Feduk, R. S.

2018-03-01

One of the trends in construction material science is development and implementation of highly effective finish materials which improve architectural exterior of cities. Silicate materials widely-used in the construction today have rather low decorative properties. Different coloring agents are used in order to produce competitive materials, but due to the peculiarities of the production, process very strict specifications are applied to them. The use of industrial wastes or variety of rock materials as coloring agents is of great interest nowadays. The article shows that clay rock can be used as raw material in production of finish materials of non-autoclaved solidification. This raw material due to its material composition actively interacts with cementing component in steam treatment at 90–95 °C with formation of cementing joints that form a firm coagulative-cristalized and crystallization structure of material providing high physic-mechanical properties of silicate goods. It is determined that energy-saving, colored finish materials with compression strength up to 16 MPa can be produced from clay rocks.

Accelerated Insertion of Materials - Composites

DTIC Science & Technology

2001-08-28

Details • Damage Tolerance • Repair • Validation of Analysis Methodology • Fatigue • Static • Acoustic • Configuration Details • Damage Tolerance...Sensitivity – Fatigue – Adhesion – Damage Tolerance – All critical modes and environments Products: Material Specifications, B-Basis Design Allowables...Demonstrate damage tolerance AIM-C DARPA DARPA Workshop, Annapolis, August 27-28, 2001 Requalification of Polymer / Composite Parts • Material Changes – Raw

Opportunity and development of bio-based composites

Treesearch

Zhiyong Cai; Jerrold E. Winandy

2005-01-01

Our forests are a naturally renewable resource that has been used as a principal source of bio-energy and building materials for centuries. The rapid growth of world population has now resulted in substantial increases in demand and in consumption of all raw materials. This now provides a unique opportunity of developing new bio-based composites. The 100-year history...

Methodology for the Assessment of the Ecotoxicological Potential of Construction Materials

PubMed Central

Rodrigues, Patrícia; Silvestre, José D.; Flores-Colen, Inês; Viegas, Cristina A.; de Brito, Jorge; Kurad, Rawaz; Demertzi, Martha

2017-01-01

Innovation in construction materials (CM) implies changing their composition by incorporating raw materials, usually non-traditional ones, which confer the desired characteristics. However, this practice may have unknown risks. This paper discusses the ecotoxicological potential associated with raw and construction materials, and proposes and applies a methodology for the assessment of their ecotoxicological potential. This methodology is based on existing laws, such as Regulation (European Commission) No. 1907/2006 (REACH—Registration, Evaluation, Authorization and Restriction of Chemicals) and Regulation (European Commission) No. 1272/2008 (CLP—Classification, Labelling and Packaging). Its application and validation showed that raw material without clear evidence of ecotoxicological potential, but with some ability to release chemicals, can lead to the formulation of a CM with a slightly lower hazardousness in terms of chemical characterization despite a slightly higher ecotoxicological potential than the raw materials. The proposed methodology can be a useful tool for the development and manufacturing of products and the design choice of the most appropriate CM, aiming at the reduction of their environmental impact and contributing to construction sustainability. PMID:28773011

40 CFR 63.2232 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORIES National Emission Standards for Hazardous Air Pollutants: Plywood and Composite Wood Products What... process units associated with the manufacturing of plywood and composite wood products. The affected... onsite storage and preparation of raw materials used in the manufacture of plywood and/or composite wood...

Utilization of flotation wastes of copper slag as raw material in cement production.

PubMed

Alp, I; Deveci, H; Süngün, H

2008-11-30

Copper slag wastes, even if treated via processes such as flotation for metal recovery, still contain heavy metals with hazardous properties posing environmental risks for disposal. This study reports the potential use of flotation waste of a copper slag (FWCS) as iron source in the production of Portland cement clinker. The FWCS appears a suitable raw material as iron source containing >59% Fe(2)O(3) mainly in the form of fayalite (Fe(2)SiO(4)) and magnetite (Fe(3)O(4)). The clinker products obtained using the FWCS from the industrial scale trial operations over a 4-month period were characterised for the conformity of its chemical composition and the physico-mechanical performance of the resultant cement products was evaluated. The data collected for the clinker products produced using an iron ore, which is currently used as the cement raw material were also included for comparison. The results have shown that the chemical compositions of all the clinker products including those of FWCS are typical of a Portland cement clinker. The mechanical performance of the standard mortars prepared from the FWCS clinkers were found to be similar to those from the iron ore clinkers with the desired specifications for the industrial cements e.g. CEM I type cements. Furthermore, the leachability tests (TCLP and SPLP) have revealed that the mortar samples obtained from the FWCS clinkers present no environmental problems while the FWCS could act as the potential source of heavy metal contamination. These findings suggest that flotation wastes of copper slag (FWCS) can be readily utilised as cement raw material due to its availability in large quantities at low cost with the further significant benefits for waste management/environmental practices of the FWCS and the reduced production and processing costs for cement raw materials.

Strength and deformability of compressed concrete elements with various types of non-metallic fiber and rods reinforcement under static loading

NASA Astrophysics Data System (ADS)

Nevskii, A. V.; Baldin, I. V.; Kudyakov, K. L.

2015-01-01

Adoption of modern building materials based on non-metallic fibers and their application in concrete structures represent one of the important issues in construction industry. This paper presents results of investigation of several types of raw materials selected: basalt fiber, carbon fiber and composite fiber rods based on glass and carbon. Preliminary testing has shown the possibility of raw materials to be effectively used in compressed concrete elements. Experimental program to define strength and deformability of compressed concrete elements with non-metallic fiber reinforcement and rod composite reinforcement included design, manufacture and testing of several types of concrete samples with different types of fiber and longitudinal rod reinforcement. The samples were tested under compressive static load. The results demonstrated that fiber reinforcement of concrete allows increasing carrying capacity of compressed concrete elements and reducing their deformability. Using composite longitudinal reinforcement instead of steel longitudinal reinforcement in compressed concrete elements insignificantly influences bearing capacity. Combined use of composite rod reinforcement and fiber reinforcement in compressed concrete elements enables to achieve maximum strength and minimum deformability.

Epoxy composites based on inexpensive tire waste filler

NASA Astrophysics Data System (ADS)

Ahmetli, Gulnare; Gungor, Ahmet; Kocaman, Suheyla

2014-05-01

Tire waste (TW) was recycled as raw material for the preparation of DGEBA-type epoxy composite materials. The effects of filler amount and epoxy type on the mechanical properties of the composites were investigated. Tensile strength and Young's modulus of the composites with NPEL were generally higher than composites with NPEF. The appropriate mass level for TW in both type composites was found to be 20 wt%. The equilibrium water sorption of NPEL/TW and NPEF/TW composites for 14-day immersion was determined as 0.10 % and 0.21 %, respectively. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used for characterization of the composites.

Polymeric materials from renewable resources

NASA Astrophysics Data System (ADS)

Frollini, Elisabete; Rodrigues, Bruno V. M.; da Silva, Cristina G.; Castro, Daniele O.; Ramires, Elaine C.; de Oliveira, Fernando; Santos, Rachel P. O.

2016-05-01

The goals of our studies have been the use of renewable raw materials in the preparation of polymeric materials with diversified properties. In this context, lignosulfonate, which is produced in large scale around the world, but not widely used in the production of polymeric materials, was used to replace phenol and polyols in the preparation of phenolic- (Ligno-PH) and polyurethane-type (Ligno-PU) polymers, respectively. These polymers were used to prepare composites reinforced with sisal lignocellulosic fibers. The use of lignosulfonate in the formulation of both types of polymers was beneficial, because in general composites with improved properties, specially impact strength, were obtained. Composites were also prepared from the so called "biopolyethylene" (HDPE), curaua lignocellulosic fiber, and castor oil (CO). All composites HDBPE/CO/Fiber exhibited higher impact strength, when compared to those of the corresponding HDBPE/Fiber. These results, combined with others (eg SEM images of the fractured surfaces) indicated that, in addition to acting as a plasticizer, this oil may have acted as a compatibilizer of the hydrophilic fiber with the hydrophobic polymer. The set of results indicated that (i) mats with nano (diameter ≤ 100nm) and/or ultrafine (submicron scale) fibers were produced, (ii) hybrid fibers were produced (bio-based mats composites), (iii) cellulosic pulp (CP) and/or lignin (Lig) can be combined with PET matrices to control properties such as stiffness and hydrophilicity of the respective mats. Materials with diversified properties were prepared from high content of renewable raw materials, thus fulfilling the proposed targets.

Importance of granulometry on phase evolution and phase-to-phase relationships of experimentally burned impure limestones intended for production of hydraulic lime and/or natural cement

NASA Astrophysics Data System (ADS)

Kozlovcev, Petr; Přikryl, Richard; Přikrylová, Jiřina

2015-04-01

In contrast to modern ordinary Portland cement production from finely ground raw material blends, ancient burning of hydraulic lime was conducted by burning larger pieces of natural raw material. Due to natural variability of raw material composition, exploitation of different beds from even one formation can result the product with significantly different composition and/or properties. Prague basin (Neoproterozoic to pre-Variscan Palaeozoic of the central part of the Bohemian Massif - the so-called Barrandian area, Czech Republic) represents a classical example of the limestone-rich region with long-term history of limestone burning for quick lime and/or various types of hydraulic binders. Due to the fact that burning of natural hydraulic lime has been abandoned in this region at the turn of 19th/20th c., significant gap in knowledge on the behavior of various limestone types and on the influence of minor variance in composition on the quality of burned product is encountered. Moreover, the importance of employment of larger pieces of raw material for burning for the development of proper phase-to-phase relationships (i.e. development of hydraulic phases below sintering temperature at mutual contacts of minerals) has not been examined before. To fill this gap, a representative specimens of major limestone types from the Prague basin have been selected for experimental study: Upper Silurian limestone types (Přídolí and Kopanina Lms.), and Lower Devonian limestones (Radotín, Kotýs, Řeporyje, Dvorce-Prokop, and Zlíchov Lms.). Petrographic character of the experimental material was examined by polarizing microscopy, cathodoluminescence, scanning electron microscopy with an energy dispersive spectrometer (SEM-EDS), and X-ray diffraction (XRD) of insoluble residue. Based on the data from wet silicate analyses, modal composition of studied impure limestones was computed. Experimental raw material was burned in laboratory electric furnace at 1000 and 1200°C for 3 and/or 6 hours. Burned samples were examined by XRD for phase composition and by SEM-EDS for phase-to-phase relationships due to the burning. Based on our data it is evident that larnite-belite (dicalcium-silicate) is dominant phase in burned silica-rich limestones (represented by e.g. Dvorce-Prokop, Přídolí and/or Kopanina Lms.). In clay-rich limestones containing kaolinite and illite, gehlenite and other calcium aluminates and aluminosilicates were detected (represented by Kosoř, Řeporyje, and/or a portion of Dvorce-Prokop Lms.). Due to higher proportion of Fe-oxihydroxides in the Řeporyje Lms., brownmillerite (calcium aluminoferrite) forms as a typical minor phases during burning. Free-lime (plus its hydrated form - portlandite) makes dominant phase in limestones exhibiting low non-carbonate admixture (Kotýs and/or a portion of Kopanina Lms.). These results clearly demonstrate that presence of certain non-carbonate minerals governs formation of certain hydraulic phases in burned product, whilst mutual proportions of individual minerals in raw materials influence amount of newly formed phases.

Clues for biomimetics from natural composite materials

PubMed Central

Lapidot, Shaul; Meirovitch, Sigal; Sharon, Sigal; Heyman, Arnon; Kaplan, David L; Shoseyov, Oded

2013-01-01

Bio-inspired material systems are derived from different living organisms such as plants, arthropods, mammals and marine organisms. These biomaterial systems from nature are always present in the form of composites, with molecular-scale interactions optimized to direct functional features. With interest in replacing synthetic materials with natural materials due to biocompatibility, sustainability and green chemistry issues, it is important to understand the molecular structure and chemistry of the raw component materials to also learn from their natural engineering, interfaces and interactions leading to durable and highly functional material architectures. This review will focus on applications of biomaterials in single material forms, as well as biomimetic composites inspired by natural organizational features. Examples of different natural composite systems will be described, followed by implementation of the principles underlying their composite organization into artificial bio-inspired systems for materials with new functional features for future medicine. PMID:22994958

Clues for biomimetics from natural composite materials.

PubMed

Lapidot, Shaul; Meirovitch, Sigal; Sharon, Sigal; Heyman, Arnon; Kaplan, David L; Shoseyov, Oded

2012-09-01

Bio-inspired material systems are derived from different living organisms such as plants, arthropods, mammals and marine organisms. These biomaterial systems from nature are always present in the form of composites, with molecular-scale interactions optimized to direct functional features. With interest in replacing synthetic materials with natural materials due to biocompatibility, sustainability and green chemistry issues, it is important to understand the molecular structure and chemistry of the raw component materials to also learn from their natural engineering, interfaces and interactions leading to durable and highly functional material architectures. This review will focus on applications of biomaterials in single material forms, as well as biomimetic composites inspired by natural organizational features. Examples of different natural composite systems will be described, followed by implementation of the principles underlying their composite organization into artificial bio-inspired systems for materials with new functional features for future medicine.

Biodegradable/Compostable Composites From Ligno-Cellulosic Fibers

USDA-ARS?s Scientific Manuscript database

The increased importance of renewable resources for raw materials and recyclabi1ity/biodegradability of the product at the end of the useful life are demanding a shift from petroleum-based synthetics to agro-based natural fibers in automotive interiors. Natural fiber composites can contribute greatl...

Recycling the product of thermal transformation of cement-asbestos for the preparation of calcium sulfoaluminate clinker.

PubMed

Viani, Alberto; Gualtieri, Alessandro F

2013-09-15

According to recent resolutions of the European Parliament (2012/2065(INI)), the need for environmentally friendly alternative solutions to landfill disposal of hazardous wastes, such as asbestos-containing materials, prompts their recycling as secondary raw materials (end of waste concept). In this respect, for the first time, we report the recycling of the high temperature product of cement-asbestos, in the formulation of calcium sulfoaluminate cement clinkers (novel cementitious binders designed to reduce CO₂ emissions), as a continuation of a previous work on their systematic characterization. Up to 29 wt% of the secondary raw material was successfully introduced into the raw mix. Different clinker samples were obtained at 1250 °C and 1300 °C, reproducing the phase composition of industrial analogues. As an alternative source of Ca and Si, this secondary raw material allows for a reduction of the CO₂ emissions in cement production, mitigating the ecological impact of cement manufacturing, and reducing the need for natural resources. Copyright © 2013 Elsevier B.V. All rights reserved.

78 FR 13352 - Government-Owned Inventions; Availability for Licensing

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-27

... traceability for the receipt of raw materials from their source to the dispensing of finished pharmaceutical... MRI imaging Competitive Advantages: Improved resolution through composite imagery Background...

Epoxy composites based on inexpensive tire waste filler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmetli, Gulnare, E-mail: ahmetli@selcuk.edu.tr; Gungor, Ahmet, E-mail: ahmetli@selcuk.edu.tr; Kocaman, Suheyla, E-mail: ahmetli@selcuk.edu.tr

2014-05-15

Tire waste (TW) was recycled as raw material for the preparation of DGEBA-type epoxy composite materials. The effects of filler amount and epoxy type on the mechanical properties of the composites were investigated. Tensile strength and Young’s modulus of the composites with NPEL were generally higher than composites with NPEF. The appropriate mass level for TW in both type composites was found to be 20 wt%. The equilibrium water sorption of NPEL/TW and NPEF/TW composites for 14-day immersion was determined as 0.10 % and 0.21 %, respectively. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used for characterization ofmore » the composites.« less

Mechanical properties of experimental composites with different calcium phosphates fillers.

PubMed

Okulus, Zuzanna; Voelkel, Adam

2017-09-01

Calcium phosphates (CaPs)-containing composites have already shown good properties from the point of view of dental restorative materials. The purpose of this study was to examine the crucial mechanical properties of twelve hydroxyapatite- or tricalcium phosphate-filled composites. The raw and surface-treated forms of both CaP fillers were applied. As a reference materials two experimental glass-containing composites and one commercial dental restorative composite were applied. Nano-hardness, elastic modulus, compressive, flexural and diametral tensile strength of all studied materials were determined. Application of statistical methods (one-way analysis of variance and cluster agglomerative analysis) allowed for assessing the similarities between examined materials according to the values of studied parameters. The obtained results show that in almost all cases the mechanical properties of experimental CaPs-composites are comparable or even better than mechanical properties of examined reference materials. Copyright © 2017 Elsevier B.V. All rights reserved.

One-dimensional carbon-sulfur composite fibers for Na-S rechargeable batteries operating at room temperature.

PubMed

Hwang, Tae Hoon; Jung, Dae Soo; Kim, Joo-Seong; Kim, Byung Gon; Choi, Jang Wook

2013-09-11

Na-S batteries are one type of molten salt battery and have been used to support stationary energy storage systems for several decades. Despite their successful applications based on long cycle lives and low cost of raw materials, Na-S cells require high temperatures above 300 °C for their operations, limiting their propagation into a wide range of applications. Herein, we demonstrate that Na-S cells with solid state active materials can perform well even at room temperature when sulfur-containing carbon composites generated from a simple thermal reaction were used as sulfur positive electrodes. Furthermore, this structure turned out to be robust during repeated (de)sodiation for ~500 cycles and enabled extraordinarily high rate performance when one-dimensional morphology is adopted using scalable electrospinning processes. The current study suggests that solid-state Na-S cells with appropriate atomic configurations of sulfur active materials could cover diverse battery applications where cost of raw materials is critical.

Optimisation of steam distillation extraction oil from onion by response surface methodology and its chemical composition.

PubMed

Wang, Zhao Dan; Li, Li Hua; Xia, Hui; Wang, Feng; Yang, Li Gang; Wang, Shao Kang; Sun, Gui Ju

2018-01-01

Oil extraction from onion was performed by steam distillation. Response surface methodology was applied to evaluate the effects of ratio of water to raw material, extraction time, zymolysis temperature and distillation times on yield of onion oil. The maximum extraction yield (1.779%) was obtained as following conditions: ratio of water to raw material was 1, extraction time was 2.5 h, zymolysis temperature was 36° and distillation time was 2.6 h. The experimental values agreed well with those predicted by regression model. The chemical composition of extracted onion oil under the optimum conditions was analysed by gas chromatography-mass spectrometry technology. The results showed that sulphur compounds, like alkanes, sulphide, alkenes, ester and alcohol, were the major components of onion oil.

Thorium and Uranium in the Rock Raw Materials Used For the Production of Building Materials

NASA Astrophysics Data System (ADS)

Pękala, Agnieszka

2017-10-01

Thorium and uranium are constant components of all soils and most minerals thereby rock raw materials. They belong to the particularly dangerous elements because of their natural radioactivity. Evaluation of the content of the radioactive elements in the rock raw materials seems to be necessary in the early stage of the raw material evaluation. The rock formations operated from deposits often are accumulated in landfills and slag heaps where the concentration of the radioactive elements can be many times higher than under natural conditions. In addition, this phenomenon may refer to buildings where rock raw materials are often the main components of the construction materials. The global control system of construction products draws particular attention to the elimination of used construction products containing excessive quantities of the natural radioactive elements. In the presented study were determined the content of thorium and uranium in rock raw materials coming from the Bełachatów lignite deposit. The Bełchatów lignite deposit extracts mainly lignite and secondary numerous accompanying minerals with the raw material importance. In the course of the field works within the framework of the carried out work has been tested 92 samples of rocks of varied petrographic composition. There were carried out analyses of the content of the radioactive elements for 50 samples of limestone of the Jurassic age, 18 samples of kaolinite clays, and 24 samples of siliceous raw materials, represented by opoka-rocks, diatomites, gaizes and clastic rocks. The measurement of content of the natural radioactive elements thorium and uranium based on measuring the frequency counts of gamma quantum, recorded separately in measuring channels. At the same time performed measurements on volume patterns radioactive: thorium and uranium. The studies were carried out in Mazar spectrometer on the powdered material. Standardly performed ten measuring cycles, after which were calculated the concentration of radioactive elements in the sample. The highest concentration of thorium and uranium has been found in the clayey raw material. Their value was respectively from 8 to 12 mg/kg for thorium and from 2.3 to 3.5 mg/kg for uranium. In carbonate sediments the content of thorium was at the level from 0.5 to 2.1 mg/kg and uranium from 0.5-2.2 mg/kg. From a group of the siliceous raw materials the diatomite had a highest concentrations of radioactive elements where the content of thorium was from 1.5 to 1.8 mg/kg and uranium from 1.3 to 1.7 mg/kg.

Chemistry of grapes and other fruits as the raw materials involved in winemaking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gallander, J.F.

The chemical composition of raw fruits is significant in winemaking and wine quality. The chemistry of grapes is particularly important to winemaking, but the composition of other fruits such as apples, pears, cherries, and blackberries is also discussed. Sugars in fruits and their importance in winemaking are discussed. Since wine acidity is essential to biological stability and tartness, information concerning organic acids is presented for several fruits. The occurrence and significance to winemaking of other essential constituents of fruits such as vitamins, enzymes, pectins, minerals, aromatic volatiles, and nitrogenous and phenolic substances are also discussed. 277 references.

Methods to improve efficiency of production technology of the innovative composite cementing materials

NASA Astrophysics Data System (ADS)

Babaevsky, A. N.; Romanovich, A. A.; Glagolev, E. S.

2018-03-01

The article describes the energy-saving technology and equipment for production of composite binding material with up to a 50% reduction in energy consumption of the process due to a synergistic effect in mechanical activation of the raw mix where a clinker component is substituted with an active mineral supplement. The impact of the gap between the rollers on the final performance of the press roller mill was studied.

Typification of cider brandy on the basis of cider used in its manufacture.

PubMed

Rodríguez Madrera, Roberto; Mangas Alonso, Juan J

2005-04-20

A study of typification of cider brandies on the basis of the origin of the raw material used in their manufacture was conducted using chemometric techniques (principal component analysis, linear discriminant analysis, and Bayesian analysis) together with their composition in volatile compounds, as analyzed by gas chromatography with flame ionization to detect the major volatiles and by mass spectrometric to detect the minor ones. Significant principal components computed by a double cross-validation procedure allowed the structure of the database to be visualized as a function of the raw material, that is, cider made from fresh apple juice versus cider made from apple juice concentrate. Feasible and robust discriminant rules were computed and validated by a cross-validation procedure that allowed the authors to classify fresh and concentrate cider brandies, obtaining classification hits of >92%. The most discriminating variables for typifying cider brandies according to their raw material were 1-butanol and ethyl hexanoate.

The influence of composition and final pyrolysis temperature variations on global kinetics of combustion of segregated municipal solid waste

NASA Astrophysics Data System (ADS)

Pranoto; Himawanto, D. A.; Arifin, N. A.

2017-04-01

The combustion of segregated municipal solid waste (MSW) and the resulted char from the pyrolysis process were investigated in this research. The segregated MSW that was collected and used can be divided into organic and inorganic waste materials. The organic materials were bamboo and banana leaves and the inorganic materials were Styrofoam and snack wrappings. The composition ratio of the waste was based on the percentage of weight of each sample. The thermal behaviour of the segregated MSW was investigated by thermo gravimetric analysis. For the pyrolysis process the prepared samples of 200gram were heated from ambient temperature until a variance of final pyrolysis temperature of 550°C, 650°C and 750°C at a constant heating rate of 25°C/min. It was found that the highest activation energy of the raw materials is achieved from sample CC1 (Char with 100% inorganic materials). The activation energy of the raw materials is relatively lower than that of the char. The higher the final pyrolysis temperature, the lower the calorific value of char. The calorific value gradually increases with the amount of inorganic materials.

The Effect of Micro/Nano-metrics Size on the Interaction of Jordanian Aluminosilicate Raw Materials with High pH Solution

NASA Astrophysics Data System (ADS)

Aldabsheh, Islam; Garcia-Valles, Maite; Martinez, Salvador

2014-05-01

Environmental preservation has become a driving force behind the search for new sustainable and environmentally friendly composites to replace conventional concrete produced from ordinary Portland cement (OPC). Current researches concentrate on developing building products (geopolymers) through geopolymerization. The goal is to produce low cost construction materials for green housing. Geopolymerization is the process of polymerizing minerals with high silica and alumina at low temperature by the use of alkali solutions. Dissolution is the most important process for supplying the high initial Al and Si concentrations to produce the gel phase that is responsible for geopolymerization. This study has been focused on the influence of different micrometric particle sizes of three Jordanian raw materials on their dissolution behavior in sodium hydroxide solution. The samples are kaolinite, volcanic tuff and silica sand. The dissolution properties of each material, alone and mixed with the other two materials were studied in different concentrations (5 and 10 M) using (NaOH) at 25ºC, and shaking time for 24 and 168 h. To better understand the dissolution process, the alkaline solution was renewed after the desired time in order to know if the Al-Si raw material is completely dissolved or not. Different analytical techniques were used to characterize raw materials physically, mineralogically, chemically and thermally. All processed samples either centrifuged solutions or solid residues were fully characterized. The leached concentrations of Al and Si were determined by inductively coupled plasma (ICP). X-ray Diffraction Technique (XRD), Scanning Electron Microscopy (SEM), and Thermo Gravimetric Analysis (TGA) were used to evaluate the solid residue characterization compared with the original ones. The three aluminosilicate raw materials have indicated variable degrees of solubility under highly alkaline conditions. The method for the size reduction of the used raw materials achieved by using a ball mill increased the dissolution rate owing to the increased surface area of the material or particle exposed to the solvent. The used Jordanian raw materials are potential to be used for geopolymerization. This work was partly financed by SGR 2009SGR-00444

Deformation of metal brackets: a comparative study.

PubMed

Flores, D A; Choi, L K; Caruso, J M; Tomlinson, J L; Scott, G E; Jeiroudi, M T

1994-01-01

The purpose of this study was to determine the effect of material and design on the force and stress required to permanently deform metal brackets. Fourteen types of metal brackets were categorized according to raw material composition, slot torque degree, and wing type. Five types of raw materials, three types of slot torque degree, and four types of wing design were tested using an archwire torque test developed by Flores. An analysis of variance (ANOVA) and t-test showed that all three categories had a significant effect on the force and stress needed to permanently deform metal brackets. Of the three, raw material had the greatest effect on the amount of force. Results showed that 17-4PH and 303S had higher yield strengths and regular twin brackets had higher resistance to deformation. Also, as slot torque degree increased, brackets deformed with less force. Result confirmed that brackets requiring the greatest stress to permanently deform were made of steel with the greatest hardness.

Strategy to Overcome Effect of Raw Materials on Enzymatic Process of Biodiesel from Non-edible Oils Using Candida sp. 99-125 Lipase.

PubMed

Nie, Kaili; Wang, Fang; Tan, Tianwei; Liu, Luo

2015-11-01

Non-edible oils are preferred raw materials for biodiesel production. However, the properties of raw materials significantly affect the synthesis process, leading to difficulties to design one process suitable for any kind of raw material. In this study, the composition of five typical non-edible oils was analyzed. The major difference was the content of free fatty acids, reflected from their acid values. The influence of different oils was investigated by using lipase from Candida sp. 99-125. At low lipase dosage and low water content, the conversion was found proportional to the acid value. However, by increasing the water content or lipase dosage, we observed that the conversions for all kinds of oils used in this study could exceed 80%. Time course analysis indicates that the lipase used in this study catalyzed hydrolysis followed by esterification, rather than direct transesterification. Accumulation of free fatty acids at the very beginning was necessary. A high water content facilitated the hydrolysis of oils with low acid value. This lipase showed capability to transform all the oils by controlling the water content.

Optimization of formulation and processing of Moringa oleifera and spirulina complex tablets.

PubMed

Zheng, Yi; Zhu, Fan; Lin, Dan; Wu, Jun; Zhou, Yichao; Mark, Bohn

2017-01-01

Objective: To prepare a more comprehensive nutrition, more balanced proportion of natural nutritional supplement tablets with Moringa oleifera leaves and spirulina the two nutrients which have complementary natural food ingredients. Method: On the basis of research M. oleifera leaves with spirulina nutrient composition was determined on M. oleifera leaves and spirulina ratio of raw materials, and the choice of microcrystalline cellulose, sodium salt of caboxy methyl cellulose(CMC),magnesium stearate excipient, through single factor and orthogonal experiment, selecting the best formula tablets prepared by powder direct compression technology, for preparation of M. oleifera and spirulina complex tablets. Results: The best ratio of raw material for the M. oleifera leaves powder: spirulina powder was 7:3, the best raw materials for the tablet formulation was 88.5%, 8.0% microcrystalline cellulose, CMC 2.0%, stearin magnesium 1.5%, the optimum parameters for the raw material crushing 200-300 mesh particle size, moisture content of 7%, tableting pressure 40 kN. Conclusion: Through formulation and process optimization, we can prepare more comprehensive and balanced nutrition M. oleifera and spirulina complex tablets, its sheet-shaped appearance, piece weight variation, hardness, friability, disintegration and other indicators have reached the appropriate quality requirements.

Design, durability and low cost processing technology for composite fan exit guide vanes

NASA Technical Reports Server (NTRS)

Blecherman, S. S.

1979-01-01

A lightweight composite fan exit guide vane for high bypass ratio gas turbine engine application was investigated. Eight candidate material/design combinations were evaluated by NASTRAN finite element analyses. A total of four combinations were selected for further analytical evaluation, part fabrication by two ventors, and fatigue test in dry and wet condition. A core and shell vane design was chosen in which the unidirectional graphite core fiber was the same for all candidates. The shell material, fiber orientation, and ply configuration were varied. Material tests were performed on raw material and composite specimens to establish specification requirements. Pre-test and post-test microstructural examination and nondestructive analyses were conducted to determine the effect of material variations on fatigue durability and failure mode. Relevant data were acquired with respect to design analysis, materials properties, inspection standards, improved durability, weight benefits, and part price of the composite fan exit guide vane.

Recycling of asbestos tailings used as reinforcing fillers in polypropylene based composites.

PubMed

Zhai, Wensi; Wang, Yao; Deng, Yuan; Gao, Hongli; Lin, Zhen; Li, Mao

2014-04-15

In this work, asbestos tailings were recycled and used as reinforcing fillers to enhance the mechanical properties of polypropylene (PP). A silane coupling agent was used to chemically modify the asbestos tailings to increase the compatibility between asbestos tailings and polypropylene matrix. Both raw and chemically treated asbestos tailings with different loading levels (from 3 to 30 wt%) were utilized to fabricate composites. Mechanical properties of these composites have been investigated by dynamic mechanical analysis, tensile test and notched impact test. Results showed that hybridization of asbestos tailings in the composites enhanced the mechanical properties of neat PP evidently, and treated asbestos tailings/PP composites yielded even better mechanical properties compared with those of raw asbestos tailings/PP composites. This recycling method of asbestos tailings not only reduces disposal costs and avoids secondary pollution but also produces a new PP-based composite material with enhanced mechanical properties. Copyright © 2014 Elsevier B.V. All rights reserved.

Electrochemical performance of Li-rich oxide composite material coated with Li0.75La0.42TiO3 ionic conductor

NASA Astrophysics Data System (ADS)

Yang, Chun-Chen; Liao, Pin-Ci; Wu, Yi-Shiuan; Lue, Shingjiang Jessie

2017-03-01

Li-rich (spray-dried (SP)-Li1.2Ni0.2Mn0.60O2) composite materials were prepared via two-step ball-mill and spray dry methods by using LiOH, α-MnO2, β-Ni(OH)2 raw materials. Two raw materials of α-MnO2 nanowires and microsphere β-Ni(OH)2 were synthesized by a hydrothermal process. In addition, Li0.75La0.42TiO3 (LLTO) fast ionic conductor was coated on SP-Li1.2Ni0.2Mn0.60O2 composite via a sol-gel method. The properties of the LLTO-coated SP-Li1.2Ni0.2Mn0.60O2 composites were determined by X-ray diffraction, scanning electron microscopy, micro-Raman, XPS, and the AC impedance method. The discharge capacities of 1 wt.%-LLTO-coated SP-Li1.2Ni0.2Mn0.60O2 composites were 256, 250, 231, 200, 158, and 114 mAh g-1 at rates of 0.1, 0.2, 0.5, 1, 3, and 5C, respectively, in the voltage range 2.0-4.8 V. The 1 wt.%-LLTO-coated Li-rich oxide composite showed the discharge capacities of up to 256 mAh g-1 in the first cycle at 0.1C. After 30 cycles, the discharge capacity of 244 mAh g-1 was obtained, which showed the capacity retention of 95.4%.

Effect of Raw Material, Pressing and Glycosidase on the Volatile Compound Composition of Wine Made From Goji Berries.

PubMed

Yuan, Guanshen; Ren, Jie; Ouyang, Xiaoyu; Wang, Liying; Wang, Mengze; Shen, Xiaodong; Zhang, Bolin; Zhu, Baoqing

2016-10-02

This study investigated the effect of raw material, pressing, and glycosidase on the aromatic profile of goji berry wine. The free-run and the pressed juice of dried and fresh goji berries were used for wine production, whereas glycosidase was applied to wine after fermentation. Dried goji berry fermented wine exhibited much stronger fruity, floral, caramel, and herbaceous odors due to higher levels of esters, β-ionone and methionol. However, fresh berry fermented wine possessed stronger chemical notes due to higher levels of 4-ethylphenol. Pressing treatment reduced the fruity and caramel odors in these fermented wines, and fresh berry free-run juice fermented wine exhibited the least floral aroma. Glycosidase addition did not alter the aromatic composition of wines. The principal component analysis indicated that goji raw material played a primary role in differentiating the aromatic profiles of the wines due to the difference on the content of 20 esters, nine benzenes, eight aldehydes/ketones, three acids, two alcohols and six other volatiles. The content differences on isopentyl alcohol, styrene, benzyl alcohol, 1-octanol, ( E )-5-decen-1-ol, 1-hexanol, and β-cyclocitral resulted in the segregation of the wines with and without the pressing treatment, especially for fresh berry fermented wine.

Analysis of the relation between the cellulose, hemicellulose and lignin content and the thermal behavior of residual biomass from olive trees.

PubMed

Garcia-Maraver, A; Salvachúa, D; Martínez, M J; Diaz, L F; Zamorano, M

2013-11-01

The heterogeneity of biomass makes it difficult if not impossible to make sweeping generalizations concerning thermochemical treatment systems and the optimal equipment to be used in them. Chemical differences in the structural components of the biomass (cellulose, hemicellulose, and lignin) have a direct impact on its chemical reactivity. The aim of this research was to study the influence of the organic components of the raw material from olive trees (leaves, pruning residues, and wood) in the combustion behavior of this biomass, as well as to find the component responsible for the higher ash content of olive leaves. Accordingly, the study used a thermogravimetric analyzer to monitor the different states and complex transitions that occurred in the biomass as the temperature varied. The decomposition rates of the different samples were analyzed in order to establish a link between each combustion phase and the composition of the raw materials. Two methods were used to determine the hemicellulose and cellulose contents of biomass from olive trees. Significant differences among the results obtained by the different methods were observed, as well as important variations regarding the chemical composition and consequently the thermal behavior of the raw materials tested. Copyright © 2013 Elsevier Ltd. All rights reserved.

Opportunities of using bio-based materials for value-added composites

Treesearch

Zhiyong Cai

2010-01-01

Our forests are a naturally renewable resource that has been used as a principal source of bio-energy and building materials for centuries. The growth of world population and affluence has resulted in substantial increases in demand and in consumption for all raw materials. Resulting increases in demand for wood products provides a unique opportunity for developing new...

"Greener" hybrid adhesives composed of urea formaldehyde resin and cottonseed meal for wood based composites

USDA-ARS?s Scientific Manuscript database

Urea formaldehyde (UF) resins are one of the most widely used adhesives in wood based composites. The major concerns of the resin utilization are free formaldehyde release and poor water resistance. As a renewable raw materials, water washed conttonseed meal can be used in wood bonding. To produce “...

Application of far infrared rare earth mineral composite materials to liquefied petroleum gas.

PubMed

Zhu, Dongbin; Liang, Jinsheng; Ding, Yan; Xu, Anping

2010-03-01

Far infrared rare earth mineral composite materials were prepared by the coprecipitation method using tourmaline, cerium acetate, and lanthanum acetate as raw materials. The results of Fourier transform infrared spectroscopy show that tourmaline modified with the rare earths La and Ce has a better far infrared emitting performance. Through XRD analysis, we attribute the improved far infrared emission properties of the tourmaline to the unit cell shrinkage of the tourmaline arising from La enhancing the redox properties of nano-CeO2. The effect of the composite materials on the combustion of liquefied petroleum gas (LPG) was studied by the flue gas analysis and water boiling test. Based on the results, it was found that the composite materials could accelerate the combustion of LPG, and that the higher the emissivity of the rare earth mineral composite materials, the better the effects on combustion of LPG. In all activation styles, both air and LPG to be activated has a best effect, indicating the activations having a cumulative effect.

Preparation and characterization of bio-composite PEEK/nHA

NASA Astrophysics Data System (ADS)

Jin, Y. S.; Bian, C. C.; Zhang, Z. Q.; Zhao, Y.; Yang, L.

2017-01-01

PEEK/nHA composite material, with excellent mechanical property as polyetheretherketone (PEEK) and biological activity as hydroxyapatite (HA), has attracted wide attention of medical experts and materials science experts. The addition of hydroxyapatite was the decisive factor for biological activity in PEEK/nHA composite. In this paper, acicular nanohydroxyapatite was prepared by chemical precipitation method with Ca(NO3)2, (NH4)2HPO4 as raw material; PEEK/nHA composite was prepared by solution blending and vacuum sintering method. The composite was characterized with FT-IR, XRD, DSC, TG and mechanical property test. Results showed that the composite has good thermal stability and compressive property when the mass ratio of PEEK to nHA is 10:3; and high nHA content can improve the biological activity of the composite, which can meet the basic requirements for bone tissue engineering scaffold.

Cost minimization through optimized raw material quality composition

Treesearch

Urs Buehlmann; R. Edward Thomas; Xiaoqui Zuo

2011-01-01

Lumber, a heterogeneous, anisotropic material produced from sawing logs, contains a varying number of randomly dispersed, unusable areas (defects) distributed over each boards’ surface area. Each board's quality is determined by the frequency and distribution of these defects and the board's dimension. Typically, the industry classifies lumber into five...

Innovative Fly Ash Geopolymer-Epoxy Composites: Preparation, Microstructure and Mechanical Properties.

PubMed

Roviello, Giuseppina; Ricciotti, Laura; Tarallo, Oreste; Ferone, Claudio; Colangelo, Francesco; Roviello, Valentina; Cioffi, Raffaele

2016-06-09

The preparation and characterization of composite materials based on geopolymers obtained from fly ash and epoxy resins are reported for the first time. These materials have been prepared through a synthetic method based on the concurrent reticulation of the organic and inorganic components that allows the formation of hydrogen bonding between the phases, ensuring a very high compatibility between them. These new composites show significantly improved mechanical properties if compared to neat geopolymers with the same composition and comparable performances in respect to analogous geopolymer-based composites obtained starting from more expensive raw material such as metakaolin. The positive combination of an easy synthetic approach with the use of industrial by-products has allowed producing novel low cost aluminosilicate binders that, thanks to their thixotropicity and good adhesion against materials commonly used in building constructions, could be used within the field of sustainable building.

Innovative Fly Ash Geopolymer-Epoxy Composites: Preparation, Microstructure and Mechanical Properties

PubMed Central

Roviello, Giuseppina; Ricciotti, Laura; Tarallo, Oreste; Ferone, Claudio; Colangelo, Francesco; Roviello, Valentina; Cioffi, Raffaele

2016-01-01

The preparation and characterization of composite materials based on geopolymers obtained from fly ash and epoxy resins are reported for the first time. These materials have been prepared through a synthetic method based on the concurrent reticulation of the organic and inorganic components that allows the formation of hydrogen bonding between the phases, ensuring a very high compatibility between them. These new composites show significantly improved mechanical properties if compared to neat geopolymers with the same composition and comparable performances in respect to analogous geopolymer-based composites obtained starting from more expensive raw material such as metakaolin. The positive combination of an easy synthetic approach with the use of industrial by-products has allowed producing novel low cost aluminosilicate binders that, thanks to their thixotropicity and good adhesion against materials commonly used in building constructions, could be used within the field of sustainable building. PMID:28773582

Peculiarities of physical and chemical processes of clinker formation in raw mixes with increased content of magnesium oxide in presence of barite waste

NASA Astrophysics Data System (ADS)

Novoselova, I. N.; Novosyolov, A. G.

2018-03-01

The article considers the influence of barite waste on clinker formation processes in raw mixes with the increased content of magnesium oxide. A by-product of the barite concentrate manufacture of Tolcheinskoye deposit has been used as a barite waste, its predominant content of barium sulphate BaSO4 amounts to 76,11%. The impact of BaO and SO3 has been revealed, particularly the impact of barium oxide on clinker formation processes in raw mixes with the increased content of magnesium oxide. It has been clarified that the addition of barite waste into a raw mix causes the formation of dicalcium silicate in two modifications, reduces the amount of alite and influences on the composition of tricalcium aluminate. Barium mono-alluminate is formed in the composition of the intermediate material. Solid solutions with barium oxide are formed in clinker phases. The authors have determined the saturation speed of calcium oxide in magnesium-bearing raw mixes with saturation coefficient (SC) 0,91 and 0,80 in the presence of 2 and 3% barite waste in the temperature range 1300-1450°C.

Effect of gas release in hot molding on flexural strength of composite friction brake

NASA Astrophysics Data System (ADS)

Rusdja, Andy Permana; Surojo, Eko; Muhayat, Nurul; Raharjo, Wijang Wisnu

2018-02-01

Composite friction brake is a vital part of braking system which serves to reduce the speed of vehicle. To fulfill the requirement of brake performance, composite friction brake must have friction and mechanical characteristic as required. The characteristics of composite friction brake are affected by brake material formulation and manufacturing parameter. In the beginning of hot molding, intermittent hot pressing was carried out to release the gases that consist of ammonia gas and water vapor. In composite friction brake, phenolic resin containing hexamethylenetetramine (HMTA) is often used as a binder. During hot molding, the reaction of phenolic resin and HMTA forms ammonia gas. Hot molding also generates water vapor because raw materials absorb moisture from environment when they are placed in storage. The gas release in hot molding is supposed affecting mechanical properties because it avoid entrapped gas in composite, so that this research investigated effect of gas release on flexural strength. Manufacturing of composite specimen was carried out as follow: mixing of raw materials, cold molding, and hot molding. In this research, duration of intermittent hot pressing and number of gas release were varied. The flexural strength of specimen was measured using three point bending test. The results showed that flexural strength specimens that were manufactured without gas release, using 4 times gas release with intermittent hot pressing for 5 and 10 seconds were not remarkably different. Conversely, hot molding using 4 times gas release with intermittent hot pressing for 15 seconds decreased flexural strength of composite. Hot molding using 2, 4, and 8 times gas release with intermittent hot pressing for 10 seconds also had no effect on increasing flexural strength. Increasing of flexural strength of composite was obtained only by using 6 times gas release with intermittent hot pressing for 10 seconds.

Three-dimensional engineered fiberboard : opportunities for the use of low valued timber and recycled material

Treesearch

John F. Hunt; David P. Harper; Katherine A. Friedrich

2004-01-01

Fiberboard sandwich panels constructed of a structural core with exterior skins can be produced with high strength and stiffness values that compare to other wood-based panels. At the same time, as much as two-thirds less material is used in the process compared to commercial wood composite products. This offers large savings in raw material and weight. The panel...

Utilization of composite membrane polyethyleneglycol-polystyrene-cellulose acetate from pineapple leaf fibers in lowering levels of methyl orange batik waste

NASA Astrophysics Data System (ADS)

Delsy, E. V. Y.; Irmanto; Kazanah, F. N.

2017-02-01

Pineapple leaves are agricultural waste from the pineapple that the fibers can be utilized as raw material in cellulose acetate membranes. First, made pineapple leaf fibers into pulp and then converted into cellulose acetate by acetylation process in four stages consisting of activation, acetylation, hydrolysis and purification. Cellulose acetate then used as the raw material to manufacture composite membrane with addition of polystyrene and poly (ethylene glycol) as porogen. Composite membrane is made using phase inversion method with dichloromethane-acetone as a solvent. The result of FTIR analysis (Fourier transform infra-red) showed that the absorption of the carbonyl group (C=O) is at 1643.10 cm-1 and acetyl group (C-O ) at 1227.01 cm-1, with a molecular weight of 8.05 x 104 g/mol and the contents (rate) of acetyl is 37.31%. PS-PEG-CA composite membrane had also been characterized by measuring the water flux values and its application to decrease methyl orange content (level) in batik waste. The results showed that the water flux value is of 25.62 L/(m2.hour), and the decrease percentage of methyl orange content in batik waste is 71.53%.

Chemical Principles Revisited: The Chemistry of Glass.

ERIC Educational Resources Information Center

Kolb, Doris; Kolb, Kenneth E.

1979-01-01

Presents a detailed discussion on the chemistry of glass. Topics discussed include: natural glass, early history, modern glass composition, raw materials for glass melting, chemically modified glasses, modern glass forming, glass ceramics, and new developments in glass research. (BT)

From raw material to dish: pasta quality step by step.

PubMed

Sicignano, Angelo; Di Monaco, Rossella; Masi, Paolo; Cavella, Silvana

2015-10-01

Pasta is a traditional Italian cereal-based food that is popular worldwide because of its convenience, versatility, sensory and nutritional value. The aim of this review is to present a step-by-step guide to facilitate the understanding of the most important events that can affect pasta characteristics, directing the reader to the appropriate production steps. Owing to its unique flavor, color, composition and rheological properties, durum wheat semolina is the best raw material for pasta production. Although pasta is traditionally made from only two ingredients, sensory quality and chemical/physical characteristics of the final product may vary greatly. Starting from the same ingredients, there are a lot of different events in each step of pasta production that can result in the development of varieties of pasta with different characteristics. In particular, numerous studies have demonstrated the importance of temperature and humidity conditions of the pasta drying operation as well as the significance of the choice of raw material and operating conditions on pasta quality. © 2015 Society of Chemical Industry.

Freezing of meat raw materials affects tyramine and diamine accumulation in spontaneously fermented sausages.

PubMed

Bover-Cid, Sara; Miguelez-Arrizado, M Jesús; Luz Latorre Moratalla, L; Vidal Carou, M Carmen

2006-01-01

Biogenic amine accumulation was studied in spontaneously fermented sausages (Fuet) manufactured from unfrozen-fresh meat (U-sausages) and frozen-thawed meat (F-sausages). The aim was to investigate whether the frozen storage of raw materials affects the microbial composition and its aminogenic activity during sausage fermentation. Tyramine was the major amine in all sausages. Although the final levels were similar, tyramine accumulated more rapidly in F-sausages, which contained putrescine as the second amine. By contrast, U-sausages accumulated much more cadaverine than putrescine. F-sausages showed a slightly lower pH and free amino acid content as well as higher counts of technological flora (lactic acid and gram positive catalase positive bacteria) and lower counts of enterobacteria. Therefore, to freeze the meat raw materials for few days before sausage manufacture could be a useful practice, especially for the artisan fermented sausages (without starter), because it helps to reduce enterobacteria development and cadaverine production.

Influence of sugarcane bagasse variability on sugar recovery for cellulosic ethanol production.

PubMed

Andrade, Liliane Pires; Crespim, Elaine; de Oliveira, Nilton; de Campos, Rafael Carinha; Teodoro, Juliana Conceição; Galvão, Célia Maria Araújo; Maciel Filho, Rubens

2017-10-01

In the context of cellulosic ethanol production, special attention must be given to the raw material, as it affects final product yield. As observed for sugarcane, bagasse variations may derive from several elements, for instance edaphoclimatic factors, seasonality, maturation stage and harvesting techniques. Therefore, in the present work, to investigate the impact of raw material characteristics on process performance, sugarcane bagasse from four harvests from October/2010 to October/2011 was pretreated by steam explosion and had its soluble and insoluble solids contents measured, following enzymatic hydrolysis to assess glucan conversion. As confirmed by ANOVA, glucose concentration was related to the solids content in the reactor, whereas glucan conversion was related to the enzymatic load. Variations in raw material composition were indeed observed to significantly interfere in the final sugar recovery, probably due to the increase in the impurities observed as a result of the type of harvest performed in 2011. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mechanochemical synthesis of carbon-based nanocomposites for supercapacitors

NASA Astrophysics Data System (ADS)

Mateyshina, Yuliya G.; Ulihin, Artem S.; Uvarov, Nikolai F.

2014-12-01

New nanoporous carbon-SiO2 composite materials were synthesized from organic raw materials (rice shells) and their electrochemical properties were investigated by cyclic voltammetry in liquid electrolytes (6 M KOH or 1 M H2SO4). A correlation between specific capacitance and specific surface area was observed. Due to high specific capacitance of 90 F/g the carbon materials under study may be regarded as promising electrode materials for electrochemical supercapacitors.

Manufacture of mold of polymeric composite water pipe reinforced charcoal

NASA Astrophysics Data System (ADS)

Zulfikar; Misdawati; Idris, M.; Nasution, F. K.; Harahap, U. N.; Simanjuntak, R. K.; Jufrizal; Pranoto, S.

2018-03-01

In general, household wastewater pipelines currently use thermoplastic pipes of Polyvinyl Chloride (PVC). This material is known to be not high heat resistant, contains hazardous chemicals (toxins), relatively inhospitable, and relatively more expensive. Therefore, researchers make innovations utilizing natural materials in the form of wood charcoal as the basic material of making the water pipe. Making this pipe requires a simple mold design that can be worked in the scale of household and intermediate industries. This research aims to produce water pipe mold with simple design, easy to do, and making time relatively short. Some considerations for molding materials are weight of mold, ease of raw material, strong, sturdy, and able to cast. Pipe molds are grouped into 4 (four) main parts, including: outer diameter pipe molding, pipe inside diameter, pipe holder, and pipe alignment control. Some materials have been tested as raw materials for outer diameter of pipes, such as wood, iron / steel, cement, and thermoset. The best results are obtained on thermoset material, where the process of disassembling is easier and the resulting mold weight is relatively lighter. For the inside diameter of the pipe is used stainless steel, because in addition to be resistant to chemical processes that occur, in this part of the mold must hold the press load due to shrinkage of raw materials of the pipe during the process of hardening (polymerization). Therefore, it needs high pressure resistant material and does not blend with the raw material of the pipe. The base of the mold is made of stainless steel material because it must be resistant to corrosion due to chemical processes. As for the adjustment of the pipe is made of ST 37 carbon steel, because its function is only as a regulator of the alignment of the pipe structure.

Preparation of food supplements from oilseed cakes.

PubMed

Sunil, L; Appaiah, Prakruthi; Prasanth Kumar, P K; Gopala Krishna, A G

2015-05-01

Oilseed cakes have been in use for feed preparation. Being rich in proteins, antioxidants, fibers, vitamins and minerals, oilseed cakes have been considered ideal for food supplementation. These oilseed cakes can be processed and made more palatable and edible by suitable treatments and then incorporated as food supplements for human consumption. Rice bran pellets (RBP), stabilized rice bran (SRB), coconut cake (CC) and sesame cake (SC) were taken up for the study. These were mixed with distilled water and cooked in such a way to separate the cooked solid residue and liquid extract followed by freeze drying to get two products from each. The raw, cooked dried residue and extract were analyzed for various parameters such as moisture (0.9-27.4 %), fat (2.1-16.1 %), ash (3.3-9.0 %), minerals (2.6-633.2 mg/100 g), total dietary fiber (23.2-58.2 %), crude fiber (2.7-10.5 %), protein (3.2-34.0 %), and the fat further analyzed for fatty acid composition, oryzanol (138-258 mg/100 g) and lignan (99-113 mg/100 g) contents and also evaluated sensory evaluation. Nutritional composition of products as affected by cooking was studied. The cooked products (residue and extract) showed changes in nutrients content and composition from that of the starting cakes and raw materials, but retained more nutrients in cooked residue than in the extract. The sensory evaluation of cooked residue and extract showed overall higher acceptability by the panelists than the starting cakes and raw materials. On the basis of these findings it can be concluded that these cooked residue and extract products are highly valuable for food supplementation than the raw ones.

Development and application of new composite grouting material for sealing groundwater inflow and reinforcing wall rock in deep mine.

PubMed

Jinpeng, Zhang; Limin, Liu; Futao, Zhang; Junzhi, Cao

2018-04-04

With cement, bentonite, water glass, J85 accelerator, retarder and water as raw materials, a new composite grouting material used to seal groundwater inflow and reinforce wall rock in deep fractured rock mass was developed in this paper. Based on the reaction mechanism of raw material, the pumpable time, stone rate, initial setting time, plastic strength and unconfined compressive strength of multi-group proportion grouts were tested by orthogonal experiment. Then, the optimum proportion of composite grouting material was selected and applied to the grouting engineering for sealing groundwater inflow and reinforcing wall rock in mine shaft lining. The results show the mixing proportion of the maximum pumpable time, maximum stone rate and minimum initial setting time of grout are A K4 B K1 C K4 D K2 , A K3 B K1 C K1 D K4 and A K3 B K3 C K4 D K1 , respectively. The mixing proportion of the maximum plastic strength and unconfined compressive strength of grouts concretion bodies are A K1 B K1 C K1 D K3 and A K1 B K1 C K1 D K1 , respectively. Balanced the above 5 indicators overall and determined the optimum proportion of grouts: bentonite-cement ratio of 1.0, water-solid ratio of 3.5, accelerator content of 2.9% and retarder content of 1.45%. This new composite grouting material had good effect on the grouting engineering for sealing groundwater inflow and reinforcing wall rock in deep fractured rock mass.

Characterization of wood plastic composites made from landfill-derived plastic and sawdust: Volatile compounds and olfactometric analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Félix, Juliana S., E-mail: jfelix@unizar.es; Domeño, Celia, E-mail: cdomeno@unizar.es; Nerín, Cristina, E-mail: cnerin@unizar.es

Graphical abstract: This work details the characterization of VOCs of WPC, produced from residual materials which would have landfills as current destination, and evaluates their odor profile. Highlights: ► More than 140 volatile compounds were identified in raw materials and WPC products. ► Markers were related to the thermal degradation, sawdust or coupling agents. ► WPC prototype showed a characteristic odor profile of burnt, sweet and wax-like. ► Aldehydes, carboxylic acids, ketones and phenols were odor descriptors of WPC. - Abstract: Application of wood plastic composites (WPCs) obtained from recycled materials initially intended for landfill is usually limited by theirmore » composition, mainly focused on release of volatile organic compounds (VOCs) which could affect quality or human safety. The study of the VOCs released by a material is a requirement for new composite materials. Characterization and quantification of VOCs of several WPC produced with low density polyethylene (LDPE) and polyethylene/ethylene vinyl acetate (PE/EVA) films and sawdust were carried out, in each stage of production, by solid phase microextraction in headspace mode (HS-SPME) and gas chromatography–mass spectrometry (GC–MS). An odor profile was also obtained by HS-SPME and GC–MS coupled with olfactometry analysis. More than 140 compounds were observed in the raw materials and WPC samples. Some quantified compounds were considered WPC markers such as furfural, 2-methoxyphenol, N-methylphthalimide and 2,4-di-tert-butylphenol. Hexanoic acid, acetic acid, 2-methoxyphenol, acetylfuran, diacetyl, and aldehydes were the most important odorants. None of the VOCs were found to affect human safety for use of the WPC.« less

The use of graphene based materials for fuel cell, photovoltaics, and supercapacitor electrode materials

NASA Astrophysics Data System (ADS)

Tsang, Alpha C. H.; Kwok, Holly Y. H.; Leung, Dennis Y. C.

2017-05-01

This manuscript presents the methodology of the production of 2D and 3D graphene based material, and their applications in fuel cell, supercapacitor, and photovoltic in recent years. Due to the uniqueness and attractive properties of graphene nanosheets, a large number of techniques have been developed for raw graphene preparation, from a chemical method to a physical deposition of carbon vapor under extreme conditions. A variety of graphene based materials were also prepared from raw graphene or graphene oxide, including the metal loaded, metal oxides loaded, to the foreign elements doped graphene. Both two-dimensional (2D) to three-dimensional (3D) structured graphene were covered. These materials included the bulk or template hybrid composite, containing graphene hydrogel, graphene aerogel, or graphene foam and its derived products. They were widely used in green energy device research, which exhibited strong activity, and developed some special usage in recent research.

Self-standing elastomeric composites based on lithium ferrites and their dielectric behavior

NASA Astrophysics Data System (ADS)

Soreto Teixeira, S.; Graça, M. P. F.; Dionisio, M.; Ilcíkova, M.; Mosnacek, J.; Spitalsky, Z.; Krupa, I.; Costa, L. C.

2014-12-01

Lithium ferrite (LiFe5O8) is an attractive material for technological applications due to its physical properties, which are significantly dependent on the preparation method and raw materials. In this work, LiFe5O8 crystallites were obtained by controlled heat-treatment process at 1100 °C, of a homogeneous mixture of Li2O-Fe2O3 powders, prepared by wet ball-milling and using lithium and iron nitrates as raw materials. The main goal was the preparation of a flexible and self-standing tick composite film by embedding lithium ferrite particles in a polymeric matrix, taking advantage of the good mechanical properties of the polymer and of the electrical and dielectric properties of the ferrite. The selected polymer matrix was styrene-b-isoprene-b-styrene copolymer. To prepare the composites, the lithium ferrite particles were chemically modified in order to functionalize their surface. To analyse the influence of the particles surface modification, different composites were made, with modified and unmodified particles. The structure of the obtained composites was studied by FTIR, XRD, TGA, and DSC techniques. The dielectric properties were analysed, in the frequency range between 10 Hz and 1 MHz and in function of temperature in the range between -73 °C and 127 °C. These properties were related with the structure and concentration of the particles in the matrix network. The composites with the modified particles present higher dielectric constant, maintaining values of loss tangent sufficiently low (<10-2) that can be considered interesting for technological applications.

Thermal highly porous insulation materials made of mineral raw materials

NASA Astrophysics Data System (ADS)

Mestnikov, A.

2015-01-01

The main objective of the study is to create insulating foam based on modified mineral binders with rapid hardening. The results of experimental studies of the composition and properties of insulating foam on the basis of rapidly hardening Portland cement (PC) and gypsum binder composite are presented in the article. The article proposes technological methods of production of insulating foamed concrete and its placement to the permanent shuttering wall enclosures in monolithic-frame construction and individual energy-efficient residential buildings, thus reducing foam shrinkage and improving crack-resistance.

High-Purity Composite Briquette for Direct UMG-Si Production in Arc Furnaces

NASA Astrophysics Data System (ADS)

Perruchoud, Raymond; Fischer, Jean-Claude

2013-12-01

In metallurgical grade Si (MG-Si), the coal (B) and charcoal (P) contents are on average above 30 ppm as the carbon reduction materials used in the arc furnace are either rich in B or in P. A decrease of both impurities by a factor of 3 using purer raw materials would allow for the direct production of the upgraded metallurgical grade (UMG).This would significantly improve the efficiency of the resulting photovoltaic (PV) cells made with the refined solar grade silicon (SoG-Si) or massively decrease the costs of Si purification by shortening the number of steps needed for reaching B and P contents below 1 ppm requested for the SoG-Si used for the PV cells. A composite C/SiO2 briquette fulfilling the purity targets for the direct production of UMG-Si in the arc furnace was developed. The composite contains several carbon materials with different levels of reactivities and quartz sand. The raw materials aspects, the paste and briquette preparation, as well as the final carbonization step are discussed. The finished briquettes are free of volatiles and are mechanically and thermally very stable, thus, ensuring stable arc furnace charges with minimum losses of dust and SiO gas. Semi-industrial trials including the downstream purification steps for the production of SoG-Si by a metallurgical low-cost route are contemplated.

Transitioning glass-ceramic scintillators for diagnostic x-ray imaging from the laboratory to commercial scale

NASA Astrophysics Data System (ADS)

Beckert, M. Brooke; Gallego, Sabrina; Elder, Eric; Nadler, Jason

2016-10-01

This study sought to mitigate risk in transitioning newly developed glass-ceramic scintillator technology from a laboratory concept to commercial product by identifying the most significant hurdles to increased scale. These included selection of cost effective raw material sources, investigation of process parameters with the most significant impact on performance, and synthesis steps that could see the greatest benefit from participation of an industry partner that specializes in glass or optical component manufacturing. Efforts focused on enhancing the performance of glass-ceramic nanocomposite scintillators developed specifically for medical imaging via composition and process modifications that ensured efficient capture of incident X-ray energy and emission of scintillation light. The use of cost effective raw materials and existing manufacturing methods demonstrated proof-of-concept for economical viable alternatives to existing benchmark materials, as well as possible disruptive applications afforded by novel geometries and comparatively lower cost per volume. The authors now seek the expertise of industry to effectively navigate the transition from laboratory demonstrations to pilot scale production and testing to evince the industry of the viability and usefulness of composite-based scintillators.

Insects: A nutritional alternative

NASA Technical Reports Server (NTRS)

Dufour, P. A.

1981-01-01

Insects are considered as potential food sources in space. Types of insects consumed are discussed. Hazards of insect ingestion are considered. Insect reproduction, requirements, and raw materials conversion are discussed. Nutrition properties and composition of insects are considered. Preparation of insects as human food is discussed.

Effects of limestone petrography and calcite microstructure on OPC clinker raw meals burnability

NASA Astrophysics Data System (ADS)

Galimberti, Matteo; Marinoni, Nicoletta; Della Porta, Giovanna; Marchi, Maurizio; Dapiaggi, Monica

2017-10-01

Limestone represents the main raw material for ordinary Portland cement clinker production. In this study eight natural limestones from different geological environments were chosen to prepare raw meals for clinker manufacturing, aiming to define a parameter controlling the burnability. First, limestones were characterized by X-Ray Fluorescence, X-Ray Powder Diffraction and Optical Microscopy to assess their suitability for clinker production and their petrographic features. The average domains size and the microstrain of calcite were also determined by X-Ray Powder Diffraction line profile analysis. Then, each limestone was admixed with clay minerals to achieve the adequate chemical composition for clinker production. Raw meals were thermally threated at seven different temperatures, from 1000 to 1450 °C, to evaluate their behaviour on heating by ex situ X-Ray Powder Diffraction and to observe the final clinker morphology by Scanning Electron Microscopy. Results indicate the calcite microstrain is a reliable parameter to predict the burnability of the raw meals, in terms of calcium silicates growth and lime consumption. In particular, mixtures prepared starting from high-strained calcite exhibit a better burnability. Later, when the melt appears this correlation vanishes; however differences in the early burnability still reflect on the final clinker composition and texture.

Environmentally-Friendly Geopolymeric Binders Made with Silica

NASA Astrophysics Data System (ADS)

Erdogan, S. T.

2013-12-01

Portland cement (PC) is the ubiquitous binding material for constructions works. It is a big contributor to global warming and climate change since its production is responsible for 5-10 % of all anthropogenic CO2 emissions. Half of this emission arises from the calcination of calcareous raw materials and half from kiln fuel burning and cement clinker grinding. Recently there have been efforts to develop alternative binders with lower greenhouse gas emissions. One such class of binders is geopolymers, formed by activating natural or waste materials with suitable alkaline or acidic solutions. These binders use natural or industrial waste raw materials with a very low CO2 footprint from grinding of the starting materials, and some from the production of the activating chemicals. The total CO2 emissions from carefully formulated mixtures can be as low as 1/10th - 1/5th of those of PC concrete mixtures with comparable properties. While use of industrial wastes as raw materials is environmentally preferable, the variability of their chemical compositions over time renders their use difficult. Use of natural materials depletes resources but can have more consistent properties and can be more easily accepted. Silica sand is a natural material containing very high amounts of quartz. Silica fume is a very fine waste from silicon metal production that is mostly non-crystalline silica. This study describes the use of sodium hydroxide and sodium silicate solutions to yield mortars with mechanical properties comparable to those of portland cement mortars and with better chemical and thermal durability. Strength gain is slower than with PC mixtures at room temperature but adequate ultimate strength can be achieved with curing at slightly elevated temperatures in less than 24 h. The consistency of the chemical compositions of these materials and their abundance in several large, developing countries makes silica attractive for producing sustainable concretes with reduced carbon footprints.

Effect of Chemical Washing Pre-treatment of Empty Fruit Bunch (EFB) biochar on Characterization of Hydrogel Biochar composite as Bioadsorbent

NASA Astrophysics Data System (ADS)

Meri, N. H.; Alias, A. B.; Talib, N.; Rashid, Z. A.; Wan, W. A.; Ghani, Ab Karim

2018-05-01

Hydrogel biochar composite (HBC) is a recent interest among researchers because of the hydrophilic characteristic which can adsorb chemical fluid and showed a versatile potential as adsorbent in removing hazardous material in wastewater and gas stream. In this study, the effect of chemical washing pre-treatment by using two different type of chemical agent Hydrochloric Acid (HCL) and Hydrogen Peroxide (H2O2) was analysed and investigated. The raw EFB biochar was prepared using microwave assisted pyrolysis under 1000W for 30 min under N2 flow with 150 mL/min. To improve the adsoprtion ability, the EFB biochar has been chemical washed pre-treatment with Hydrochloric Acid (HCl) and Hydrogen Peroxide (H2O2) before polymerization process with acrylamide (AAm) as monomer, N,N’-methylenebisacrylamide (MBA) as crosslinker and ammonium persulfate (APS) as initiator. The characterization has studied by using Fourier transform infrared spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC). FTIR result shows that, the formation of Raw EFB to Hydrogel Biochar Composite (Raw EFB > EFB Biochar > Treated Biochars (HCl & H2O2) > Hydrogel Biochar Composite) have changed in functional group. For DSC result it shows that the thermal behaviour of all samples is endothermic process and have high thermal resistance.

Assessing consumer expectations about pizza: A study on celiac and non-celiac individuals using the word association technique.

PubMed

Pontual, I; Amaral, G V; Esmerino, E A; Pimentel, T C; Freitas, M Q; Fukuda, R K; Sant'Ana, I L; Silva, L G; Cruz, A G

2017-04-01

The word association (WA) technique was used to investigate the perception of two groups of consumers (72 celiac and 78 non-celiac individuals; 150 in total) to pizza dough (thick or thin) and the raw material used at the manufacture (cassava flour or rice flour). Different perceptions of the four stimuli were detected by Chi-square test (X 2 =314.393, p<0.0001) for both groups. Seven categories were used for both groups: food/composition, health, doubt/uncertainty, novelty, negative feelings, positive feelings, and sensory aspects. The stimulus 'pizza dough made with cassava flour' was associated with the category "food/composition" and the stimuli 'pizza made with rice flour', 'pizza made with cassava flour' and 'thin dough' were associated with "positive feelings". The stimulus 'thick dough' was related only to the category "negative feelings". WA indicated that gluten-free pizza should have thin dough and us cassava flour or rice flour as the raw material. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterization of Low Firing Temperature Ceramic Glaze Using Phuket MSW and Soda Lime Cullet

NASA Astrophysics Data System (ADS)

Ketboonruang, P.; Jinawat, S.; Kashima, D. P.; Wasanapiarnpong, T.; Sujaridworakun, P.; Buggakuptav, W.; Traipol, N.; Jiemsirilers, S.

2011-10-01

The normal firing temperature of ceramic products is around 1200 °C. In order to reduce firing temperature, industrial wastes were utilized in ceramic glaze. Phuket municipal solid waste (MSW), soda lime cullet, and borax were used as raw materials for low firing temperature glazes. The glaze compositions were designed using a triaxial diagram. Stoneware ceramic body was glazed then fired at 1000 and 1150 °C for 15 minutes. Morphology and phase composition of glazes were analyzed by Scanning electron microscopy (SEM-EDS) and X-ray diffraction (XRD). Thermal expansion compatibility of Stoneware body and glazes were investigated using a dilatometer. Melting behaviour of selected glaze was analyzed by heating stage microscopy. Phuket MSW and Soda lime glass cullet can be used in high percentage as major raw materials for low firing temperature ceramic glaze that show good texture and vitrified at lower firing temperature without using any commercial ceramic frits. The firing temperature can be reduced up to 150 °C in this study.

Cutin from agro-waste as a raw material for the production of bioplastics.

PubMed

Heredia-Guerrero, José A; Heredia, Antonio; Domínguez, Eva; Cingolani, Roberto; Bayer, Ilker S; Athanassiou, Athanassia; Benítez, José J

2017-11-09

Cutin is the main component of plant cuticles constituting the framework that supports the rest of the cuticle components. This biopolymer is composed of esterified bi- and trifunctional fatty acids. Despite its ubiquity in terrestrial plants, it has been underutilized as raw material due to its insolubility and lack of melting point. However, in recent years, a few technologies have been developed to obtain cutin monomers from several agro-wastes at an industrial scale. This review is focused on the description of cutin properties, biodegradability, chemical composition, processability, abundance, and the state of art of the fabrication of cutin-based materials in order to evaluate whether this biopolymer can be considered a source for the production of renewable materials. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Characterization of products obtained from pyrolysis and steam gasification of wood waste, RDF, and RPF.

PubMed

Hwang, In-Hee; Kobayashi, Jun; Kawamoto, Katsuya

2014-02-01

Pyrolysis and steam gasification of woody biomass chip (WBC) obtained from construction and demolition wastes, refuse-derived fuel (RDF), and refuse paper and plastic fuel (RPF) were performed at various temperatures using a lab-scale instrument. The gas, liquid, and solid products were examined to determine their generation amounts, properties, and the carbon balance between raw material and products. The amount of product gas and its hydrogen concentration showed a considerable difference depending on pyrolysis and steam gasification at higher temperature. The reaction of steam and solid product, char, contributed to an increase in gas amount and hydrogen concentration. The amount of liquid products generated greatly depended on temperature rather than pyrolysis or steam gasification. The compositions of liquid product varied relying on raw materials used at 500°C but the polycyclic aromatic hydrocarbons became the major compounds at 900°C irrespective of the raw materials used. Almost fixed carbon (FC) of raw materials remained as solid products under pyrolysis condition whereas FC started to decompose at 700°C under steam gasification condition. For WBC, both char utilization by pyrolysis at low temperature (500°C) and syngas recovery by steam gasification at higher temperature (900°C) might be practical options. From the results of carbon balance of RDF and RPF, it was confirmed that the carbon conversion to liquid products conspicuously increased as the amount of plastic increased in the raw material. To recover feedstock from RPF, pyrolysis for oil recovery at low temperature (500°C) might be one of viable options. Steam gasification at 900°C could be an option but the method of tar reforming (e.g. catalyst utilization) should be considered. Copyright © 2013 Elsevier Ltd. All rights reserved.

Air electrode composition for solid oxide fuel cell

DOEpatents

Kuo, Lewis; Ruka, Roswell J.; Singhal, Subhash C.

1999-01-01

An air electrode composition for a solid oxide fuel cell is disclosed. The air electrode material is based on lanthanum manganite having a perovskite-like crystal structure ABO.sub.3. The A-site of the air electrode composition comprises a mixed lanthanide in combination with rare earth and alkaline earth dopants. The B-site of the composition comprises Mn in combination with dopants such as Mg, Al, Cr and Ni. The mixed lanthanide comprises La, Ce, Pr and, optionally, Nd. The rare earth A-site dopants preferably comprise La, Nd or a combination thereof, while the alkaline earth A-site dopant preferably comprises Ca. The use of a mixed lanthanide substantially reduces raw material costs in comparison with compositions made from high purity lanthanum starting materials. The amount of the A-site and B-site dopants is controlled in order to provide an air electrode composition having a coefficient of thermal expansion which closely matches that of the other components of the solid oxide fuel cell.

Influence of Implementation of Composite Materials in Civil Aircraft Industry on reduction of Environmental Pollution and Greenhouse Effect

NASA Astrophysics Data System (ADS)

Beck, A. J.; Hodzic, A.; Soutis, C.; Wilson, C. W.

2011-12-01

Computer-based Life Cycle Analysis (LCA) models were carried out to compare lightweight composites with the traditional aluminium over their useful lifetime. The analysis included raw materials, production, useful life in operation and disposal at the end of the material's useful life. The carbon fibre epoxy resin composite could in some cases reduce the weight of a component by up to 40 % compared to aluminium. As the fuel consumption of an aircraft is strongly influenced by its total weight, the emissions can be significantly reduced by increasing the proportion of composites used in the aircraft structure. Higher emissions, compared to aluminium, produced during composites production meet their 'break even' point after certain number of time units when used in aircraft structures, and continue to save emissions over their long-term operation. The study highlighted the environmental benefits of using lightweight structures in aircraft design, and also showed that utilisation of composites in products without energy saving may lead to increased emissions in the environment.

Air electrode composition for solid oxide fuel cell

DOEpatents

Kuo, L.; Ruka, R.J.; Singhal, S.C.

1999-08-03

An air electrode composition for a solid oxide fuel cell is disclosed. The air electrode material is based on lanthanum manganite having a perovskite-like crystal structure ABO{sub 3}. The A-site of the air electrode composition comprises a mixed lanthanide in combination with rare earth and alkaline earth dopants. The B-site of the composition comprises Mn in combination with dopants such as Mg, Al, Cr and Ni. The mixed lanthanide comprises La, Ce, Pr and, optionally, Nd. The rare earth A-site dopants preferably comprise La, Nd or a combination thereof, while the alkaline earth A-site dopant preferably comprises Ca. The use of a mixed lanthanide substantially reduces raw material costs in comparison with compositions made from high purity lanthanum starting materials. The amount of the A-site and B-site dopants is controlled in order to provide an air electrode composition having a coefficient of thermal expansion which closely matches that of the other components of the solid oxide fuel cell. 3 figs.

A Potential Use of 3-D Scanning to Evaluate the Chemical Composition of Pork Meat.

PubMed

Adamczak, Lech; Chmiel, Marta; Florowski, Tomasz; Pietrzak, Dorota; Witkowski, Marcin; Barczak, Tomasz

2015-07-01

The aim of this study was to determine the possibility of 3-D scanning method in chemical composition evaluation of pork meat. The sampling material comprised neck muscles (1000 g each) obtained from 20 pork carcasses. The volumetric estimation process of the elements was conducted on the basis of point cloud collected using 3-D scanner. Knowing the weight of neck muscles, their density was calculated which was subsequently correlated with the content of basic chemical components of the pork meat (water, protein and fat content, determined by standard methods). The significant correlations (P ≤ 0.05) between meat density and water (r = 0.5213), protein (r = 0.5887), and fat (r = -0.6601) content were obtained. Based on the obtained results it seems likely to employ the 3-D scanning method to compute the meat chemical composition. The use of the 3-D scanning method in industrial practice will allow to evaluate the chemical composition of meat in online mode on a dressing and fabrication line and in a rapid, noninvasive manner. The control of the raw material using the 3-D scanning will allow to make visual assessment more objective and will enable optimal standardization of meat batches prior to processing stage. It will ensure not only the repeatability of product quality characteristics, but also optimal use of raw material-lean and fat meat. The knowledge of chemical composition of meat is essential due to legal requirements associated with mandatory nutrition facts labels on food products. © 2015 Institute of Food Technologists®

Chemical changes associated with lotus and water lily natto production

NASA Astrophysics Data System (ADS)

Lestari, S. D.; Fatimah, N.; Nopianti, R.

2017-04-01

Natto is a traditional Japanese food made by fermenting whole soybean seeds with pure culture of Bacillus subtilis subsp. natto. The purpose of this study was to investigate the suitability of lotus (Nelumbo nucifera) and water lily (Nymphaea stellata) seeds as the raw materials for natto production. Chemical (proximate, amino acids and minerals) changes were observed on raw, steamed and fermented seeds. Proximate compositions of all samples were calculated in both wet basis and dry basis. In wet basis calculation, steaming and fermentation tended to lower the carbohydrates, ashes, fats and protein content which were attributed to the increase of moisture. The total amino acid, iron and magnesium contents of raw lotus seeds were 24.29%, 5.08 mg 100g-1 and 174.23 mg 100g-1 dry matter, respectively. After a 24h-fermentation at 40°C, the total amino acids decreased while iron and magnesium contents increased significantly reaching, in respective order, 9.9 mg 100g-1 and 411.36 mg 100g-1 dry matter. Changes in chemical composition after fermentation were more pronounced in lotus seeds than water lily seeds indicating that their nutrient composition were more suitable to support Bacillus subtilis growth.

Self-standing elastomeric composites based on lithium ferrites and their dielectric behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soreto Teixeira, S.; Graça, M. P. F.; Costa, L. C.

2014-12-14

Lithium ferrite (LiFe{sub 5}O{sub 8}) is an attractive material for technological applications due to its physical properties, which are significantly dependent on the preparation method and raw materials. In this work, LiFe{sub 5}O{sub 8} crystallites were obtained by controlled heat-treatment process at 1100 °C, of a homogeneous mixture of Li{sub 2}O-Fe{sub 2}O{sub 3} powders, prepared by wet ball-milling and using lithium and iron nitrates as raw materials. The main goal was the preparation of a flexible and self-standing tick composite film by embedding lithium ferrite particles in a polymeric matrix, taking advantage of the good mechanical properties of the polymer andmore » of the electrical and dielectric properties of the ferrite. The selected polymer matrix was styrene-b-isoprene-b-styrene copolymer. To prepare the composites, the lithium ferrite particles were chemically modified in order to functionalize their surface. To analyse the influence of the particles surface modification, different composites were made, with modified and unmodified particles. The structure of the obtained composites was studied by FTIR, XRD, TGA, and DSC techniques. The dielectric properties were analysed, in the frequency range between 10 Hz and 1 MHz and in function of temperature in the range between −73 °C and 127 °C. These properties were related with the structure and concentration of the particles in the matrix network. The composites with the modified particles present higher dielectric constant, maintaining values of loss tangent sufficiently low (<10{sup −2}) that can be considered interesting for technological applications.« less

Meta-analyses of oil yield in Cuphea PSR23

USDA-ARS?s Scientific Manuscript database

Oil content and composition of Cuphea seed are of special economic value as raw materials for industrial and food applications. The inherent unpredictability in determining and predicting Cuphea’s oil yield is attributed, in part, to the indeterminate growth habit and the persistence of the domestic...

Adjusting Permittivity by Blending Varying Ratios of SWNTs

NASA Technical Reports Server (NTRS)

Tour, James M.; Stephenson, Jason J.; Higginbotham, Amanda

2012-01-01

A new composite material of singlewalled carbon nanotubes (SWNTs) displays radio frequency (0 to 1 GHz) permittivity properties that can be adjusted based upon the nanotube composition. When varying ratios of raw to functionalized SWNTs are blended into the silicone elastomer matrix at a total loading of 0.5 percent by weight, a target real permittivity value can be obtained between 70 and 3. This has particular use for designing materials for microwave lenses, microstrips, filters, resonators, high-strength/low-weight electromagnetic interference (EMI) shielding, antennas, waveguides, and low-loss magneto-dielectric products for applications like radome construction.

Studies on crosslinked hydroxyapatite-polyethylene composite as a bone-analogue material

NASA Astrophysics Data System (ADS)

Smolko, E.; Romero, G.

2007-08-01

The paper examines the use of different types of polymeric matrix composites in hard-tissue replacement applications. The composite samples were prepared with hydroxyapatite (HA) powder and polyethylenes of different densities. The raw material was first compounded in the extruder and the resulting composite pre-forms were compression molded into desired plates and irradiated with different doses. Modulus of elasticity in tension, tensile strength, tensile fracture strain, elongation at break and gel content were obtained for all composites. Ceramic filler distribution was investigated under scanning electron microscopy (SEM). With HA incorporated in the samples an increase in the values of Young's Modulus, (stiffness) was observed, while elongation at break decreased with the amount of filler, showing increase of brittleness. Tensile strengths at yield and at break decreased with the filler content for LD and MDPE and stayed constant for HDPE.

Polymer-Cement Composites Containing Waste Perlite Powder

PubMed Central

Łukowski, Paweł

2016-01-01

Polymer-cement composites (PCCs) are materials in which the polymer and mineral binder create an interpenetrating network and co-operate, significantly improving the performance of the material. On the other hand, the need for the utilization of waste materials is a demand of sustainable construction. Various mineral powders, such as fly ash or blast-furnace slag, are successfully used for the production of cement and concrete. This paper deals with the use of perlite powder, which is a burdensome waste from the process of thermal expansion of the raw perlite, as a component of PCCs. The results of the testing of the mechanical properties of the composite and some microscopic observations are presented, indicating that there is a possibility to rationally and efficiently utilize waste perlite powder as a component of the PCC. This would lead to creating a new type of building material that successfully meets the requirements of sustainable construction. PMID:28773961

Innovation processes in technologies for the processing of refractory mineral raw materials

NASA Astrophysics Data System (ADS)

Chanturiya, V. A.

2008-12-01

Analysis of the grade of mineral resources of Russia and other countries shows that end products that are competitive in terms of both technological and environmental criteria in the world market can only be obtained by the development and implementation of progressive technologies based on the up-to-date achievements of fundamental sciences. The essence of modern innovation processes in technologies developed in Russia for the complex and comprehensive processing of refractory raw materials with a complex composition is ascertained. These processes include (i) radiometric methods of concentration of valuable components, (ii) high-energy methods of disintegration of highly dispersed mineral components, and (iii) electrochemical methods of water conditioning to obtain target products for solving specific technological problems.

Silica nanoparticles produced by DC arc plasma from a solid raw materials

NASA Astrophysics Data System (ADS)

Kosmachev, P. V.; Vlasov, V. A.; Skripnikova, N. K.

2017-05-01

Plasma synthesis of SiO2 nanoparticles in experimental atmospheric pressure plasma reactor on the basis of DC arc plasma generator was presented in this paper. Solid high-silica raw materials such as diatomite from Kamyshlovskoye deposit in Russia, quartzite from Chupinskoye deposit in Russia and milled window glass were used. The obtained nanoparticles were characterized based on their morphology, chemical composition and size distribution. Scanning electron microscopy, laser diffractometry, nitrogen absorption (Brunauer-Emmett-Teller method), X-ray photoelectron spectroscopy and energy-dispersive X-ray spectroscopy were used to characterize the synthesized products. The obtained silica nanoparticles are agglomerated, have spherical shape and primary diameters between 10-300 nm. All samples of synthesized nanopowders were compared with commercial nanopowders.

Study on novel functional materials carboxymethyl cellulose lithium (CMC-Li) improve high-performance lithium-ion battery.

PubMed

Qiu, Lei; Shao, Ziqiang; Xiang, Pan; Wang, Daxiong; Zhou, Zhenwen; Wang, Feijun; Wang, Wenjun; Wang, Jianquan

2014-09-22

Novel cellulose derivative CMC-Li was synthesized by cotton as raw material. The mechanism of the CMC-Li modified electrode materials by electrospinning was reported. CMC-Li/lithium iron phosphate (LiFePO4, LFP) composite fiber coated with LFP and CMC-Li nanofibers was successfully obtained by electrospinning. Then, CMC-Li/LFP nano-composite fiber was carbonized under nitrogen at a high temperature formed CNF/LFP/Li (CLL) composite nanofibers as cathode material. It can increase the contents of Li+, and improving the diffusion efficiency and specific capacity. The battery with CLL as cathode material retained close to 100% of initial reversible capacity after 200 cycles at 168 mAh g(-1), which was nearly the theoretical specific capacity of LFP. The cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), X-ray diffraction (XRD) and scanning electron microscope (SEM) were characterizing material performance. The batteries have good electrochemical property, outstanding pollution-free, excellent stability. Copyright © 2014 Elsevier Ltd. All rights reserved.

Research on self-propagating high temperature synthesis prepared ZrC-ZrB2 composite ceramic

NASA Astrophysics Data System (ADS)

Yong, Cheng; Xunjia, Su; Genliang, Hou; YaKun, Xing

2013-03-01

ZrC-ZrB2 composite ceramic material is prepared by self-propagating high temperature synthesis, using Zr powders, CrO2 powders and Al powders as raw materials. Samples are studied by XRD and SEM, the results show that: ZrC-ZrB2 composite ceramic is attained after self-propagating high-temperature reaction, with Zr+ B4C as the main reactive system, and which is added respectively different content (CrO3 + Al) system. The study finds that the ceramic composite products are mainly composed of ZrC and ZrB2 phase, and other subphase. Compared to the main reactive system composite ceramic, composite ceramic grains grow up obviously, after introduction of the highly exothermic system (CrO3 + Al) in the main reactive system, and with the gradual increase of the content (CrO3 + Al).

Effects of raw materials on the properties of wood fiber-polyethylene composites--part 3: effect of a compatibilizer and wood adhesive on the interfacial adhesion of wood/plastic composites

Treesearch

Chin-yin Hwang; Chung-yun Hse; Todd F. Shupe

2008-01-01

The objective of this study was to examine the effect of maleated polypropylene compatabilizer on the interfacial properties of wood and polyolefins. Birch wood dowels containing an adhesive applied on the surface were embedded in molten plastic matrices using specially designed jigs. The three plastics investigated included low density polyethylene (LFPE), linear low...

Metal-Matrix/Hollow-Ceramic-Sphere Composites

NASA Technical Reports Server (NTRS)

Baker, Dean M.

2011-01-01

A family of metal/ceramic composite materials has been developed that are relatively inexpensive, lightweight alternatives to structural materials that are typified by beryllium, aluminum, and graphite/epoxy composites. These metal/ceramic composites were originally intended to replace beryllium (which is toxic and expensive) as a structural material for lightweight mirrors for aerospace applications. These materials also have potential utility in automotive and many other terrestrial applications in which there are requirements for lightweight materials that have high strengths and other tailorable properties as described below. The ceramic component of a material in this family consists of hollow ceramic spheres that have been formulated to be lightweight (0.5 g/cm3) and have high crush strength [40.80 ksi (.276.552 MPa)]. The hollow spheres are coated with a metal to enhance a specific performance . such as shielding against radiation (cosmic rays or x rays) or against electromagnetic interference at radio and lower frequencies, or a material to reduce the coefficient of thermal expansion (CTE) of the final composite material, and/or materials to mitigate any mismatch between the spheres and the matrix metal. Because of the high crush strength of the spheres, the initial composite workpiece can be forged or extruded into a high-strength part. The total time taken in processing from the raw ingredients to a finished part is typically 10 to 14 days depending on machining required.

21 CFR 20.100 - Applicability; cross-reference to other regulations.

Code of Federal Regulations, 2011 CFR

2011-04-01

... of this chapter. (25) Cosmetic establishment registrations, in § 710.7 of this chapter. (26) Cosmetic product ingredient and cosmetic raw material composition statements, § 720.8 of this chapter. (27) Cosmetic product experience reports, in § 730.7 of this chapter. (28) Device premarket notification...

21 CFR 20.100 - Applicability; cross-reference to other regulations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... of this chapter. (25) Cosmetic establishment registrations, in § 710.7 of this chapter. (26) Cosmetic product ingredient and cosmetic raw material composition statements, § 720.8 of this chapter. (27) Cosmetic product experience reports, in § 730.7 of this chapter. (28) Device premarket notification...

The management challenge for household waste in emerging economies like Brazil: realistic source separation and activation of reverse logistics.

PubMed

Fehr, M

2014-09-01

Business opportunities in the household waste sector in emerging economies still evolve around the activities of bulk collection and tipping with an open material balance. This research, conducted in Brazil, pursued the objective of shifting opportunities from tipping to reverse logistics in order to close the balance. To do this, it illustrated how specific knowledge of sorted waste composition and reverse logistics operations can be used to determine realistic temporal and quantitative landfill diversion targets in an emerging economy context. Experimentation constructed and confirmed the recycling trilogy that consists of source separation, collection infrastructure and reverse logistics. The study on source separation demonstrated the vital difference between raw and sorted waste compositions. Raw waste contained 70% biodegradable and 30% inert matter. Source separation produced 47% biodegradable, 20% inert and 33% mixed material. The study on collection infrastructure developed the necessary receiving facilities. The study on reverse logistics identified private operators capable of collecting and processing all separated inert items. Recycling activities for biodegradable material were scarce and erratic. Only farmers would take the material as animal feed. No composting initiatives existed. The management challenge was identified as stimulating these activities in order to complete the trilogy and divert the 47% source-separated biodegradable discards from the landfills. © The Author(s) 2014.

Effect of the ultrasound-assisted preliminary maceration on the efficiency of the essential oil distillation from selected herbal raw materials.

PubMed

Kowalski, Radosław; Kowalska, Grażyna; Jamroz, Jerzy; Nawrocka, Agnieszka; Metyk, Damian

2015-05-01

The objective of the study was the estimation of the ultrasound-assisted preliminary maceration effect on the efficiency of essential oil distillation and on its qualitative and quantitative composition. The experiment included analyses on three herbal materials, i.e. peppermint leaves (Mentha piperita L.), marjoram herb (Origanum majorana L.), and chamomile flowers (Chamomilla recutita (L.) Rauschert). The study showed that the application of preliminary water maceration of raw material, augmented with ultrasounds, had a statistically significant increasing effect on the amount of oil distilled, in the case of mint leaf from 1.32% to 1.46% v/w, and in the case of marjoram herb from 1.13% to 1.27% v/w. In the case of chamomile flowers no significant effect of ultrasound on the amount of oil obtained was observed. Generally, comparing the composition of essential oils obtained in the experiments with the requirements of the relevant standards no unfavourable effect of the distillation augmenting techniques applied was noted. Therefore, it should be expected that the studied distillates of volatile fractions will have the desired biological activity. Copyright © 2014 Elsevier B.V. All rights reserved.

Effect of sintering process and additives on the properties of cordierite based ceramics

NASA Astrophysics Data System (ADS)

Rundans, M.; Sperberga, I.; Sedmale, G.; Stinkulis, G.

2013-12-01

It is possible to obtain cordierite ceramics with high temperature synthesis using both synthetic and raw natural materials. This paper discusses the possibilities to obtain cordierite ceramics, replacing part of required oxides with raw materials from various Latvian deposits of dolomite and clay. The obtained raw cordierite powders were ground in two modes (3 and 12 hours) and fired at 1200 °C. Ceramic samples were characterized by hydrostatic weighting method; crystalline phase composition was studied by XRD. Obtained samples were evaluated by their mechanical (compressive) strength and linear coefficient of thermal expansion (CTE). Thermal shock resistance was tested using water quenching method and afterwards evaluated by using ultrasonic method to test changes in Young's modulus of elasticity. Results show that increase in grinding time causes samples to densify and promote formation of cordierite crystalline phase which corresponds to increase in total compressive strength and decrease of CTE values. CTE values of samples ground for 12 hours conform to that of obtained in other researches.

Latest Progress In Novel High Conductivity And Highly Stable Composite Structure Developments For Satellite Applications

NASA Astrophysics Data System (ADS)

Klebor, Maximillian; Reichmann, Olaf; Pfeiffer, Ernst K.; Ihle, Alexander; Linke, Stefan; Tschepe, Christoph; Roddecke, Susanne; Richter, Ines; Berrill, Mark; Santiago-Prowald, Julian

2012-07-01

Materials such as aluminium, titanium and carbon fibre based composites are indispensable in space business. However, special demands on spaceborne applications require both new ideas and new concepts but also powerful novel materials. These days the trend is to substitute aluminium for CFRP basically in order to safe mass or to decrease thermal expansions. Nevertheless there are upcoming requirements that cannot be met using standard CFRP materials. In this connection innovative composites have to be introduced. In the frame of this paper three major applications for such material requests are considered, i.e.: • antennas • satellite platform structural panels • radiators. The new composites need to cope with the following challenges and demands: high operational temperature range, high stiffness, high strength, high thermal conductivity, vacuum compatibility, low mass, high in- orbit stability, compatibility with metallic parts and many more. Some of these demands have to be fulfilled in conjunction. Herein the innovative composites cover new raw materials and their combination, manufacturing process enhancement as well as new inspection and test methods. It has been observed that by using the developed CFRPs it is possible to satisfy and excel the needs. However, these materials feature a different behaviour than conventional composites which has to be taken into account during future design.

Technical assessment for quality control of resins

NASA Technical Reports Server (NTRS)

Gosnell, R. B.

1977-01-01

Survey visits to companies involved in the manufacture and use of graphite-epoxy prepregs were conducted to assess the factors which may contribute to variability in the mechanical properties of graphite-epoxy composites. In particular, the purpose was to assess the contributions of the epoxy resins to variability. Companies represented three segments of the composites industry - aircraft manufacturers, prepreg manufacturers, and epoxy resin manufacturers. Several important sources of performance variability were identified from among the complete spectrum of potential sources which ranged from raw materials to composite test data interpretation.

System simulation application for determining the size of daily raw material purchases at PT XY

NASA Astrophysics Data System (ADS)

Napitupulu, H. L.

2018-02-01

Every manufacturing company needs to implement green production, including PT XY as a marine catchment processing industry in Sumatera Utara Province. The company is engaged in the processing of squid for export purposes. The company’s problem relates to the absence of a decision on the daily purchase amount of the squid. The purchase of daily raw materials in varying quantities has caused companies to face the problem of excess raw materials or otherwise the lack of raw materials. The low purchase of raw materials will result in reduced productivity, while large purchases will lead to increased cooling costs for storage of excess raw materials, as well as possible loss of damage raw material. Therefore it is necessary to determine the optimal amount of raw material purchases every day. This can be determined by applying simulation. Application of system simulations can provide the expected optimal amount of raw material purchases.

Phenotyping the quality of complex medium components by simple online-monitored shake flask experiments.

PubMed

Diederichs, Sylvia; Korona, Anna; Staaden, Antje; Kroutil, Wolfgang; Honda, Kohsuke; Ohtake, Hisao; Büchs, Jochen

2014-11-07

Media containing yeast extracts and other complex raw materials are widely used for the cultivation of microorganisms. However, variations in the specific nutrient composition can occur, due to differences in the complex raw material ingredients and in the production of these components. These lot-to-lot variations can affect growth rate, product yield and product quality in laboratory investigations and biopharmaceutical production processes. In the FDA's Process Analytical Technology (PAT) initiative, the control and assessment of the quality of critical raw materials is one key aspect to maintain product quality and consistency. In this study, the Respiration Activity Monitoring System (RAMOS) was used to evaluate the impact of different yeast extracts and commercial complex auto-induction medium lots on metabolic activity and product yield of four recombinant Escherichia coli variants encoding different enzymes. Under non-induced conditions, the oxygen transfer rate (OTR) of E. coli was not affected by a variation of the supplemented yeast extract lot. The comparison of E. coli cultivations under induced conditions exhibited tremendous differences in OTR profiles and volumetric activity for all investigated yeast extract lots of different suppliers as well as lots of the same supplier independent of the E. coli variant. Cultivation in the commercial auto-induction medium lots revealed the same reproducible variations. In cultivations with parallel offline analysis, the highest volumetric activity was found at different cultivation times. Only by online monitoring of the cultures, a distinct cultivation phase (e.g. glycerol depletion) could be detected and chosen for comparable and reproducible offline analysis of the yield of functional product. This work proves that cultivations conducted in complex media may be prone to significant variation in final product quality and quantity if the quality of the raw material for medium preparation is not thoroughly checked. In this study, the RAMOS technique enabled a reliable and reproducible screening and phenotyping of complex raw material lots by online measurement of the respiration activity. Consequently, complex raw material lots can efficiently be assessed if the distinct effects on culture behavior and final product quality and quantity are visualized.

Investigation on the activation of coal gangue by a new compound method.

PubMed

Li, Chao; Wan, Jianhua; Sun, Henghu; Li, Longtu

2010-07-15

In order to comprehensively utilize coal gangue as the main raw material in cementitious materials, improving its cementitious activity is a question of fundamental importance. In this paper, we present a new compound mechanical-hydro-thermal activation (CMHTA) technology to investigate the activation effect of coal gangue, and the traditional mechanical-thermal activation (TMTA) technology was used as reference. The purpose of this study is to give a detailed comparison between these two methods with regard to the mineral composition, crystal structure and microstructure, by XRD, IR, MAS NMR, XPS and mechanical property analysis. The prepared coal gangue based blended cement, containing 52% of activated coal gangue C (by CMHTA technology), has a better mechanical property than activated coal gangue T (by TMTA technology) and raw coal gangue. The results show that both of the TMTA and CMHTA technologies can improve the cementitious activity of raw gangue greatly. Moreover, compared with TMTA, the mineral phases such as feldspar and muscovite in raw coal gangue were partially decomposed, and the crystallinity of quartz decreased, due to the effect of adding CaO and hydro-thermal process of CMHTA technology. 2010 Elsevier B.V. All rights reserved.

Tribological properties of nonasbestos brake pad material by using coconut fiber

NASA Astrophysics Data System (ADS)

Craciun, A. L.; Pinca-Bretotean, C.; Utu, D.; Josan, A.

2017-01-01

In automotive industry, the brake system is influenced by a large number of variables including geometry of components, materials of brakes, components interaction and many operating condition. Organic fiber reinforced metallic friction composites are increasingly being used in automotive brake shoes, disc and pads, linings, blocks, clutch facings, primarily because of awareness of health hazards of asbestos. Current trend in the research field of automotive industry is to utilization of different wastes as a source of raw materials for composite materials. This will provide more economical benefit and also environmental preservation by utilize the waste of natural fibre In this paper it has performed a tribological study to determine the characteristics of the friction product by using coconut natural fibred reinforced in aluminium composite. In this sense, two different laboratory formulation were prepared with 5% and 10% coconut fibre and other constitutes like binder, friction modifiers, abrasive material and solid lubrificant using powder mettallurgy. These dnew materials for brake pads are tested for tribological behaviour in a standard pin on disc tribometer. To know the wear behavior of composite materials will determine the parameters that characterize there tribological properties.

Influence of Starting Powders on Hydroxyapatite Coatings Fabricated by Room Temperature Spraying Method.

PubMed

Seo, Dong Seok; Lee, Jong Kook; Hwang, Kyu Hong; Hahn, Byung Dong; Yoon, Seog Young

2015-08-01

Three types of raw materials were used for the fabrication of hydroxyapatite coatings by using the room temperature spraying method and their influence on the microstructure and in vitro characteristics were investigated. Starting hydroxyapatite powders for coatings on titanium substrate were prepared by a heat treatment at 1100 °C for 2 h of bovine bone, bone ash, and commercial hydroxyapatite powders. The phase compositions and Ca/P ratios of the three hydroxyapatite coatings were similar to those of the raw materials without decomposition or formation of a new phase. All hydroxyapatite coatings showed a honeycomb structure, but their surface microstructures revealed different features in regards to surface morphology and roughness, based on the staring materials. All coatings consisted of nano-sized grains and had dense microstructure. Inferred from in vitro experiments in pure water, all coatings have a good dissolution-resistance and biostability in water.

Properties of Roman bricks and mortars used in Serapis temple in the city of Pergamon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ozkaya, Ozlem Aslan; Boeke, Hasan, E-mail: hasanboke@iyte.edu.tr

Serapis temple, which was constructed in the Roman period in the city of Pergamon (Bergama/Turkey), is one of the most important monuments of the world heritage. In this study, the characteristics of bricks and mortars used in the temple have been determined in order to define the necessary characteristics of the intervention materials, which will be used in the conservation works of the temple. Several analyses were carried out to determine their basic physical properties, raw material compositions, mineralogical and microstructural properties using X-ray diffraction, Scanning Electron Microscope and a Thermo Gravimetric Analyzer. Analysis results indicated that the mortars aremore » stiff, compact and hydraulic due to the use of natural pozzolanic aggregates. The Roman bricks are of low density, high porosity and were produced from raw materials containing calcium poor clays fired at low temperatures.« less

Remediation of metal polluted soils by phytorremediation combined with biochar addition

NASA Astrophysics Data System (ADS)

Méndez, Ana; Paz-Ferreiro, Jorge; Gómez-Limón, Dulce; César Arranz, Julio; Saa, Antonio; Gascó, Gabriel

2016-04-01

The main objective of this work is to optimize and quantify the treatment of metal polluted soils through phytoremediation techniques combined with the addition of biochar. Biochar is a carbon rich material obtained by thermal treatment of biomass in inert atmosphere. In recent years, it has been attracted considerable interest due to their positive effect after soil addition. The use of biochar also seems appropriate for the treatment of metal-contaminated soils decreasing their mobility. Biochar properties highly depend on the raw material composition and manufacturing conditions. This paper is based on the use of manure wastes, rich in nutrients and therefore interesting raw materials for biochar production, especially when combined with phytoremediation techniques since the biochar act as conditioner and slow release fertilizer. We are very grateful to Ministerio de Economia y Competitividad (Spain) for financial support under Project CGL2014-58322-R.

Battery related cobalt and REE flows in WEEE treatment.

PubMed

Sommer, P; Rotter, V S; Ueberschaar, M

2015-11-01

In batteries associated with waste electrical and electronic equipment (WEEE), battery systems can be found with a higher content of valuable and critical raw materials like cobalt and rare earth elements (REE) relative to the general mix of portable batteries. Based on a material flow model, this study estimates the flows of REE and cobalt associated to WEEE and the fate of these metals in the end-of-life systems. In 2011, approximately 40 Mg REE and 325 Mg cobalt were disposed of with WEEE-batteries. The end-of-life recycling rate for cobalt was 14%, for REE 0%. The volume of waste batteries can be expected to grow, but variation in the battery composition makes it difficult to forecast the future secondary raw material potential. Nevertheless, product specific treatment strategies ought to be implemented throughout the stages of the value chain. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Characteristics of the nitrous substances in the meat of sharks and rays as a protein food raw material].

PubMed

Kizevetter, I V; Nasedkina, E A

1975-01-01

The nitrous composition of meat in 19 species of oceanic sharks and 2 species of rays were analyzed. The meat of these fish species was found to be characterized by a comparatively low protein content, whose amino acids composition proved relatively poor of essential amino acids. The meat of sharks and rays is distinguished by a high level of extractives, whose bulk includes urea and trimethylaminoxide.

Study on the chemical composition features of Longquan celadon excavated from the Chuzhou site of Huai'an City in Jiangsu Province by EDXRF

NASA Astrophysics Data System (ADS)

Li, Li; Feng, Song-Lin; Feng, Xiang-Qian; Xu, Qing; Yan, Ling-Tong; Ma, Bo; Huo, Hua

2011-07-01

A mass of Longquan celadon shards were excavated from the Chuzhou site of Huai'an City in Jiangsu Province, China. These celadon shards were fired during the period of the Late Yuan Dynasty to the Tianshun era of the Ming Dynasty, as identified by archaeologists at Nanjing Museum. In order to research the chemical composition features of this ancient celadon porcelain, energy dispersive X-ray fluorescence (EDXRF) for non-destructive analysis was used to determine the chemical composition of the porcelain body and glaze in these shards. The results indicate that Ti and Fe in the body of Longquan celadon are characteristic elements which can distinguish porcelain produced during the Late Yuan Dynasty from those produced in the Ming Dynasties. The results of the principal component analysis (PCA) show that different body and glaze raw materials were used for the production of porcelain in different periods and the raw materials of the body and glaze are also different for various vessel shapes. The chemical compositions in the porcelain body of civilian ware are slightly different. The imperial and civilian Longquan celadon porcelains produced during the Hongwu era to the Tianshun era of the Ming Dynasty are distinguishable by the MnO, Fe2O3, Rb2O and SrO content in their porcelain glaze.

Surface-binding through polyfunction groups of Rhodamine B on composite surface and its high performance photodegradation

NASA Astrophysics Data System (ADS)

Wan, Yiqun; Wang, Xiaofen; Gu, Yun; Guo, Lan; Xu, Zhaodi

2016-03-01

A kind of novel composite ZnS/In(OH)3/In2S3 is synthesized using zinc oxide nanoplates as zinc raw material during hydrothermal process. Although the obtained samples are composited of ZnS and In(OH)3 and In2S3 phase, the samples possess different structure, morphology and optical absorption property depending on molar ratio of raw materials. Zeta potential analysis indicates different surface electrical property since various content and particle size of the phases. The equilibrium adsorption study confirms the composite ZnS/In(OH)3/In2S3 with surface negative charge is good adsorbent for Rhodamine B (Rh B) dye. In addition, the degradation of Rh B over the samples with surface negative charge under visible light (λ ≥ 420 nm) is more effective than the samples with surface positive charge. The samples before and after adsorbing Rh B molecule are examined by FTIR spectra and Zetasizer. It is found that the three function groups of Rh B molecule, especially carboxyl group anchors to surface of the sample through electrostatic adsorption, coordination and hydrogen-bond. It contributes to rapid transformation of photogenerated electron to conduction band of In(OH)3 and suppresses the recombination of photogenerated carrier. The possible adsorption modes of Rh B are discussed on the basis of the experiment results.

40 CFR 63.1348 - Standards for affected sources other than kilns; in-line kiln/raw mills; clinker coolers; new and...

Code of Federal Regulations, 2010 CFR

2010-07-01

... than kilns; in-line kiln/raw mills; clinker coolers; new and reconstructed raw material dryers; and raw...; in-line kiln/raw mills; clinker coolers; new and reconstructed raw material dryers; and raw and finish mills. The owner or operator of each new or existing raw material, clinker, or finished product...

A Preliminary Study on Black Colored Potsherds from Taiwan

NASA Astrophysics Data System (ADS)

Liou, Y. S.; Yi-Chang, L.

2016-12-01

Black colored potsherds from the archaeological sites of late Neolithic (3500-2000 BP) and Iron Age (1400-800 BP) exhibit the minor phase in the number of antiques, however, they represent a specific symbol on the religious rites and social stratum in the archaeological and cultural contents of Taiwan. A lot of efforts focused on morphological and decorative styles of the black pottery have been made in previous archaeological works. In this study, multiple analytical techniques including micro-Raman spectroscopy, X-ray diffraction analysis (XRD), and micro X-ray florescence spectroscopy (μXRF) were applied to 11 potsherds found at eleven archaeological sites across Taiwan to understand the raw materials, production techniques, and the possible interactions and exchange system among ancient societies. Ten mineral phases including α-quartz, amorphous carbon, anatase, plagioclase, etc., were identified from Raman spectra. The presence of amorphous carbon indicates that pottery was fired under reducing conditions. Pyroxene minerals were present in some potsherds, suggesting that raw materials were not sourced locally, and perhaps further indicating trading or people migration activities in ancient periods. XRD measurements and μXRF analyses were used as complementary techniques to obtain mineral and chemical compositions. XRD measurements show that quartz, albite, biotite, and gypsum were present in potsherds. Chemically, SiO2, Al2O3, Na2O, K2O, Fe2O3, and CaO are the main constituents. The correlation plots of these main compositions show that pottery raw material can subdivide into three group which were related to different areas and ages. However, it need more detailed investigation to decipher this issue.

Zirconia-hydroxyapatite composite material with micro porous structure.

PubMed

Matsumoto, Takuya Junior; An, Sang-Hyun; Ishimoto, Takuya; Nakano, Takayoshi; Matsumoto, Takuya; Imazato, Satoshi

2011-11-01

Titanium plates and apatite blocks are commonly used for restoring large osseous defects in dental and orthopedic surgery. However, several cases of allergies against titanium have been recently reported. Also, sintered apatite block does not possess sufficient mechanical strength. In this study, we attempted to fabricate a composite material that has mechanical properties similar to biocortical bone and high bioaffinity by compounding hydroxyapatite (HAp) with the base material zirconia (ZrO(2)), which possesses high mechanical properties and low toxicity toward living organisms. After mixing the raw material powders at several different ZrO(2)/HAp mixing ratios, the material was compressed in a metal mold (8 mm in diameter) at 5 MPa. Subsequently, it was sintered for 5 h at 1500°C to obtain the ZrO(2)/HAp composite. The mechanical property and biocompatibility of materials were investigated. Furthermore, osteoconductivity of materials was investigated by animal studies. A composite material with a minute porous structure was successfully created using ZrO(2)/HAp powders, having different particle sizes, as the starting material. The material also showed high protein adsorption and a favorable cellular affinity. When the mixing ratio was ZrO(2)/HAp=70/30, the strength was equal to cortical bone. Furthermore, in vivo experiments confirmed its high osteoconductivity. The composite material had strength similar to biocortical bones with high cell and tissue affinities by compounding ZrO(2) and HAp. The ZrO(2)/HAp composite material having micro porous structure would be a promising bone restorative material. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Implementation of recycled cellulosic fibres into cement based composites and testing their influence on resulting properties

NASA Astrophysics Data System (ADS)

Hospodarova, V.; Stevulova, N.; Vaclavik, V.; Dvorsky, T.

2017-10-01

Nowadays, the application of raw materials from renewable sources such as wood, plants and waste paper to building materials preparing has gained a significant interest in this research area. The aim of this paper is to investigate the impact of the selected plasticizer on properties of fibres composites made of cellulosic fibres coming from recycled waste paper and cement. Investigations were performed on specimens with 0.5 wt. % of fibre addition without and with plasticizer. A comparative study did not show positive influence of plasticizer on the density and thermal conductivity of 28 days hardened composite. The specimens after 1, 3 and 7 days of hardening with plasticizer exhibited the highest impact on compressive strength in comparison to composite without plasticizer but 28 days hardened specimens reached the same value of strength characteristic (41 MPa).

Kraft pulp from budworm-infested jack pine

Treesearch

J. Y. Zhu; Gary C. Myers

2006-01-01

This study evaluated the quality of kraft pulp from bud-worm-infested jack pine. The logs were classified as merchantable live, suspect, or merchantable dead. Raw materials were evaluated through visual inspection, analysis of the chemical composition, SilviScan measurement of the density, and measurement of the tracheid length. Unbleached pulps were then refined using...

[Studies on origin of illicit methamphetamine. I. The relationship of enantiomeric compositions between methamphetamine and its raw material (ephedrine)].

PubMed

Kikura, R; Shimamine, M; Nakahara, Y; Terao, T

1992-01-01

In order to elucidate the relationship of enantiomeric compositions between methamphetamine (MA) and its raw materials, ephedrine (EP) enantiomers, commercial EP samples and MA samples prepared from them were analyzed by HPLC using GITC-prelabeling. The GITC derivatives were separated on ODS column using methanol-water-acetic acid (45:54:1) at a flow rate of 1.2 ml/min for EP and tetrahydrofuran-water-acetic acid (29:70:1) at a flow rate of 1 ml/min for MA. The chromatographic conditions resulted in such a good separation of four EP and two MA enantiomers that 1/1000 enantiomeric impurities could be detected and discriminated from the major enantiomer with good reproducibility. Moreover, it was demonstrated that the asymmetric center at alpha-position of amino group was entirely retained throughout the reductive reaction of the EP samples, and that the MA samples inherited the enantiomeric character from the EP samples used. This method was applied to discriminative analysis of MA samples seized in Japan.

Characterization of Limestone as Raw Material to Hydrated Lime

NASA Astrophysics Data System (ADS)

Salem Hwidi, Rajeb; Nuraiti Tengku Izhar, Tengku; Saad, Farah Naemah Mohd

2018-03-01

In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.

Use of artificial intelligence in the production of high quality minced meat

NASA Astrophysics Data System (ADS)

Kapovsky, B. R.; Pchelkina, V. A.; Plyasheshnik, P. I.; Dydykin, A. S.; Lazarev, A. A.

2017-09-01

A design for an automatic line for minced meat production according to new production technology based on an innovative meat milling method is proposed. This method allows the necessary degree of raw material comminution at the stage of raw material preparation to be obtained, which leads to production intensification due to the traditional meat mass comminution equipment being unnecessary. To ensure consistent quality of the product obtained, the use of on-line automatic control of the technological process for minced meat production is envisaged. This system has been developed using artificial intelligence methods and technologies. The system is trainable during the operation process, adapts to changes in processed raw material characteristics and to external impacts that affect the system operation, and manufactures meat shavings with minimal dispersion of the typical particle size. The control system includes equipment for express analysis of the chemical composition of the minced meat and its temperature after comminution. In this case, the minced meat production process can be controlled strictly as a function of time, which excludes subjective factors for assessing the degree of finished product readiness. This will allow finished meat products with consistent, targeted high quality to be produced.

Real-time control data wrangling for development of mathematical control models of technological processes

NASA Astrophysics Data System (ADS)

Vasilyeva, N. V.; Koteleva, N. I.; Fedorova, E. R.

2018-05-01

The relevance of the research is due to the need to stabilize the composition of the melting products of copper-nickel sulfide raw materials in the Vanyukov furnace. The goal of this research is to identify the most suitable methods for the aggregation of the real time data for the development of a mathematical model for control of the technological process of melting copper-nickel sulfide raw materials in the Vanyukov furnace. Statistical methods of analyzing the historical data of the real technological object and the correlation analysis of process parameters are described. Factors that exert the greatest influence on the main output parameter (copper content in matte) and ensure the physical-chemical transformations are revealed. An approach to the processing of the real time data for the development of a mathematical model for control of the melting process is proposed. The stages of processing the real time information are considered. The adopted methodology for the aggregation of data suitable for the development of a control model for the technological process of melting copper-nickel sulfide raw materials in the Vanyukov furnace allows us to interpret the obtained results for their further practical application.

Utilizing thermophilic microbe in lignocelluloses based bioethanol production: Review

NASA Astrophysics Data System (ADS)

Sriharti, Agustina, Wawan; Ratnawati, Lia; Rahman, Taufik; Salim, Takiyah

2017-01-01

The utilization of thermophilic microbe has attracted many parties, particularly in producing an alternative fuel like ethanol. Bioethanol is one of the alternative energy sources substituting for earth oil in the future. The advantage of using bioethanol is that it can reduce pollution levels and global warming because the result of bioethanol burning doesn't bring in a net addition of CO2 into environment. Moreover, decrease in the reserves of earth oil globally has also contributed to the notion on searching renewable energy resources such as bioethanol. Indonesia has a high biomass potential and can be used as raw material for bioethanol. The utilization of these raw materials will reduce fears of competition foodstuffs for energy production. The enzymes that play a role in degrading lignocelluloses are cellulolytic, hemicellulolytic, and lignolytic in nature. The main enzyme with an important role in bioethanol production is a complex enzyme capable of degrading lignocelluloses. The enzyme can be produced by the thermophilik microbes of the groups of bacteria and fungi such as Trichoderma viride, Clostridium thermocellum, Bacillus sp. Bioethanol production is heavily affected by raw material composition, microorganism type, and the condition of fermentation used.

Quality design of belite–melilite clinker

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurokawa, Daisuke, E-mail: daisuke_kurokawa@taiheiyo-cement.co.jp; Department of Materials Science and Engineering, Nagoya Institute of Technology, Nagoya 466-8555; Honma, Kenichi

2013-12-15

We have developed a new cement clinker, consisting mainly of belite and melilite, which is capable of increasing the amount of recycled waste as a part of its raw materials. We analyzed clinkers with a wide range of compositions, and clarified the quantitative relationship between the chemical and mineral compositions. Clinkers consisting mostly of belite and melilite were successfully obtained at the CaO/SiO{sub 2} mass ratio of 1.7 to 1.9. Test cements were prepared using these clinkers and mixed with OPC for the evaluation of fluidity and strength. The belite–melilite cement was found to have good fluidity, and the belite–melilitemore » cement mixed with OPC at up to 30% exhibited a satisfactory long term strength equivalent to the OPC, demonstrating the potential as an alternative to OPC. Electron probe microanalysis revealed the relatively high concentration of diphosphorus pentaoxide in belite, suggesting this component might contribute to the strength enhancement of the cement. -- Highlights: •A new cement clinker consisting mainly of belite and melilite was designed. •The clinker enables the use of various recycled wastes as part of its raw materials. •The relationship between the chemical and mineral compositions was clarified. •This cement mixed with OPC at up to 30% exhibited a good quality equivalent to OPC.« less

Biomediated continuous release phosphate fertilizer

DOEpatents

Goldstein, Alan H.; Rogers, Robert D.

1999-01-01

A composition is disclosed for providing phosphate fertilizer to the root zone of plants. The composition comprises a microorganism capable of producing and secreting a solubilization agent, a carbon source for providing raw material for the microorganism to convert into the solubilization agent, and rock phosphate ore for providing a source of insoluble phosphate that is solubilized by the solubilization agent and released as soluble phosphate. The composition is provided in a physical form, such as a granule, that retains the microorganism, carbon source, and rock phosphate ore, but permits water and soluble phosphate to diffuse into the soil. A method of using the composition for providing phosphate fertilizer to plants is also disclosed.

Study of Catalyst Variation Effect in Glycerol Conversion Process to Hydrogen Gas by Steam Reforming

NASA Astrophysics Data System (ADS)

Widayat; Hartono, R.; Elizabeth, E.; Annisa, A. N.

2018-04-01

Along with the economic development, needs of energy being increase too. Hydrogen as alternative energy has many usages. Besides that, hydrogen is one source of energy that is a clean fuel, but process production of hydrogen from natural gas as a raw material has been used for a long time. Therefore, there is need new invention to produce hydrogen from the others raw material. Glycerol, a byproduct of biodiesel production, is a compound which can be used as a raw material for hydrogen production. By using glycerol as a raw material of hydrogen production, we can get added value of glycerol as well as an energy source solution. The process production of hydrogen by steam reforming is a thermochemical process with efficiency 70%. This process needs contribution of catalyst to improve its efficiency and selectivity of the process. In this study will be examined the effect variation of catalyst for glycerol conversion process to hydrogen by steam reforming. The method for catalyst preparation was variation of catalyst impregnation composition, catalyst calcined with difference concentration of hydrochloric acid and calcined with difference hydrochloric acid ratio. After that, all of catalyst which have been prepared, used for steam reforming process for hydrogen production from glycerol as a raw material. From the study, the highest yield of hydrogen gas showed in the process production by natural zeolite catalyst with 1:15 Hydrochloric acid ratio was 42.28%. Hydrogen yield for 2M calcined natural zeolite catalyst was 38.37%, for ZSM-5 catalyst was 15.83%, for 0.5M calcined natural zeolite was 13.09% and for ultrasonic natural zeolite was 11.43%. The lowest yield of hydrogen gas showed in catalyst 2Zn/ZSM-5 with 11.22%. This result showed that hydrogen yield product was affected by catalyst variation because of the catalyst has difference characteristic and difference catalytic activity after the catalyst preparation process.

Dual-carbon enhanced silicon-based composite as superior anode material for lithium ion batteries

NASA Astrophysics Data System (ADS)

Wang, Jie; Liu, Dai-Huo; Wang, Ying-Ying; Hou, Bao-Hua; Zhang, Jing-Ping; Wang, Rong-Shun; Wu, Xing-Long

2016-03-01

Dual-carbon enhanced Si-based composite (Si/C/G) has been prepared via employing the widely distributed, low-cost and environmentally friendly Diatomite mineral as silicon raw material. The preparation processes are very simple, non-toxic and easy to scale up. Electrochemical tests as anode material for lithium ion batteries (LIBs) demonstrate that this Si/C/G composite exhibits much improved Li-storage properties in terms of superior high-rate capabilities and excellent cycle stability compared to the pristine Si material as well as both single-carbon modified composites. Specifically for the Si/C/G composite, it can still deliver a high specific capacity of about 470 mAh g-1 at an ultrahigh current density of 5 A g-1, and exhibit a high capacity of 938 mAh g-1 at 0.1 A g-1 with excellent capacity retention in the following 300 cycles. The significantly enhanced Li-storage properties should be attributed to the co-existence of both highly conductive graphite and amorphous carbon in the Si/C/G composite. While the former can enhance the electrical conductivity of the obtained composite, the latter acts as the adhesives to connect the porous Si particulates and conductive graphite flakes to form robust and stable conductive network.

Identification of material properties of orthotropic composite plate using experimental frequency response function data

NASA Astrophysics Data System (ADS)

Tam, Jun Hui; Ong, Zhi Chao; Ismail, Zubaidah; Ang, Bee Chin; Khoo, Shin Yee

2018-05-01

The demand for composite materials is increasing due to their great superiority in material properties, e.g., lightweight, high strength and high corrosion resistance. As a result, the invention of composite materials of diverse properties is becoming prevalent, and thus, leading to the development of material identification methods for composite materials. Conventional identification methods are destructive, time-consuming and costly. Therefore, an accurate identification approach is proposed to circumvent these drawbacks, involving the use of Frequency Response Function (FRF) error function defined by the correlation discrepancy between experimental and Finite-Element generated FRFs. A square E-glass epoxy composite plate is investigated under several different configurations of boundary conditions. It is notable that the experimental FRFs are used as the correlation reference, such that, during computation, the predicted FRFs are continuously updated with reference to the experimental FRFs until achieving a solution. The final identified elastic properties, namely in-plane elastic moduli, Ex and Ey, in-plane shear modulus, Gxy, and major Poisson's ratio, vxy of the composite plate are subsequently compared to the benchmark parameters as well as with those obtained using modal-based approach. As compared to the modal-based approach, the proposed method is found to have yielded relatively better results. This can be explained by the direct employment of raw data in the proposed method that avoids errors that might incur during the stage of modal extraction.

Development ceramic composites based on Al2O3, SiO2 and IG-017 additive

NASA Astrophysics Data System (ADS)

Kurovics, E.; Shmakova, A.; Kanev, B.; Gömze, L. A.

2017-02-01

Based on high purity alumina and quartz powders and IG-017 bio-original additives the authors have developed new ceramic composite materials for different industrial purposes. The main goal was to fine a material and morphological structures of high performance ceramic composites as frames for development complex materials for extreme consumptions in the future. For this the mixed powders of Al2O3 , SiO2 and IG-017 bio-original additive were uniaxially pressed at different compaction pressures into disc shapes and were sintered in electric kiln under air (1) and nitrogrn (2) atmosphere. The grain size distributions of the raw materials were determined by laser granulometry. There thermo-physical properties were also determined by derivatography. The prepared and sintered specimens were tested on geometrical sizes, microstructure and morphology by scanning electron microscopy, porosity and water absorption. In this work the authors present the results of their research and investigation.

Sewage sludge as a fuel and raw material for phosphorus recovery: Combined process of gasification and P extraction.

PubMed

Gorazda, K; Tarko, B; Werle, S; Wzorek, Z

2018-03-01

Increasing problems associated with sewage sludge disposal are observed nowadays. As the thermal conversion of sewage sludge (combustion, co-combustion, gasification and pyrolysis) appears to be the most promising alternative for its management, the solid residues left after gasification were examined. The present study evaluates the potential of this waste as an alternative phosphorus source in the context of phosphorus recovery. The obtained solid gasification residues were characterised (chemical and phase composition, thermal properties, surface properties and technological parameters used for phosphorus raw materials) and compared to commercial phosphate raw materials. It was revealed that gasification residue is a valuable source of phosphorus and microelements, comparable to sewage sludge ash (SSA) considered nowadays as secondary phosphorus raw materials. Chemical properties as well as technological parameters characteristic for natural phosphate ores are different. Solid gasification residue was leached with mineral acids (phosphoric and nitric) according to the patented method of phosphorus recovery - PolFerAsh, developed by Cracow University of Technology. It was revealed that phosphorus can be selectively leached from solid gasification residue with high efficiency (73-82%); moreover, most of the iron and heavy metals stay in the solid phase due to the low concentration of acids and proper solid to liquid phase ratio. The obtained leachates are valuable products that can be considered for the production of fertilisers. Combining the gasification process with nutrient recovery provides the opportunity for more environmentally efficient technologies driven by sustainable development rules. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cost analysis of composite fan blade manufacturing processes

NASA Technical Reports Server (NTRS)

Stelson, T. S.; Barth, C. F.

1980-01-01

The relative manufacturing costs were estimated for large high technology fan blades prepared by advanced composite fabrication methods using seven candidate materials/process systems. These systems were identified as laminated resin matrix composite, filament wound resin matrix composite, superhybrid solid laminate, superhybrid spar/shell, metal matrix composite, metal matrix composite with a spar and shell, and hollow titanium. The costs were calculated utilizing analytical process models and all cost data are presented as normalized relative values where 100 was the cost of a conventionally forged solid titanium fan blade whose geometry corresponded to a size typical of 42 blades per disc. Four costs were calculated for each of the seven candidate systems to relate the variation of cost on blade size. Geometries typical of blade designs at 24, 30, 36 and 42 blades per disc were used. The impact of individual process yield factors on costs was also assessed as well as effects of process parameters, raw materials, labor rates and consumable items.

Pigment-cellulose nanofibril composite and its application as a separator-substrate in printed supercapacitors

NASA Astrophysics Data System (ADS)

Torvinen, Katariina; Lehtimäki, Suvi; Keränen, Janne T.; Sievänen, Jenni; Vartiainen, Jari; Hellén, Erkki; Lupo, Donald; Tuukkanen, Sampo

2015-11-01

Pigment-cellulose nanofibril (PCN) composites were manufactured in a pilot line and used as a separator-substrate in printed graphene and carbon nanotube supercapacitors. The composites consisted typically of 80% pigment and 20% cellulose nanofibrils (CNF). This composition makes them a cost-effective alternative as a substrate for printed electronics at high temperatures that only very special plastic films can nowadays stand. The properties of these substrates can be varied within a relatively large range by the selection of raw materials and their relative proportions. A semi-industrial scale pilot line was successfully used to produce smooth, flexible, and nanoporous composites, and their performance was tested in a double functional separator-substrate element in supercapacitors. The nanostructural carbon films printed on the composite worked simultaneously as high surface area active electrodes and current collectors. Low-cost supercapacitors made from environmentally friendly materials have significant potential for use in flexible, wearable, and disposable low-end products. [Figure not available: see fulltext.

Fabrication and characterization of high impact hybrid matrix composites from thermoset resin and dyneema-glass fabric reinforcement

NASA Astrophysics Data System (ADS)

Patel, R. H.; Sharma, S.; Pansuriya, T.; Malgani, E. V.; Sevkani, V.

2018-05-01

Hybrid composites have been fabricated by hand lay-up technique with epoxy resin and diethylene tri amine as a hardener for high impact energy absorption with sandwich stacking of different reinforcements of dyneema and glass fabric. High impact grade composites are nowadays gaining a lot of importance in the field of high mechanical load bearing applications, ballistics and bulletproofing. The present work emphases on the fabrication and mechanical properties of the hybrid composites of cut resistant dyneema fabric along with glass fabric reinforced in the thermosetting resin. i.e. epoxy. The prime importance while fabricating such materials have been given to the processing along with selection of the raw materials. High impact resistive materials with low density and henceforth low weight have been manufactured and characterized by IZOD impact tester, UTM, Archimedes density meter and SEM. Throughout the work, satisfactory results have been obtained. Impact resistance was observed to be boosted three times as that of the reference sample of glass fabric and epoxy. The density of the hybrid composite is observed to be 25% as that of the reference sample.

Lunar fiberglass: Properties and process design

NASA Technical Reports Server (NTRS)

Dalton, Robert; Nichols, Todd

1987-01-01

A Clemson University ceramic engineering design for a lunar fiberglass plant is presented. The properties of glass fibers and metal-matrix composites are examined. Lunar geology is also discussed. A raw material and site are selected based on this information. A detailed plant design is presented, and summer experiments to be carried out at Johnson Space Center are reviewed.

Task Analysis: Applying Composition Theory in an Industrial Forum.

ERIC Educational Resources Information Center

Soderston, Candace

Technical writers involved in an institutional writing project need some way of viewing the raw material globally before writing. In this way they can build a framework which can be used for different types of information. This is accomplished through a task analysis meeting that highlights the following preparatory steps prior to writing: (1)…

Biofuels from microalgae: lipid extraction and methane production from the residual biomass in a biorefinery approach.

PubMed

Hernández, D; Solana, M; Riaño, B; García-González, M C; Bertucco, A

2014-10-01

Renewable fuels and energy are of major concern worldwide and new raw materials and processes for its generation are being investigated. Among these raw materials, algae are a promising source of lipids and energy. Thus, in this work four different algae have been used for lipid extraction and biogas generation. Lipids were obtained by supercritical CO2 extraction (SCCO2), while anaerobic digestion of the lipid-exhausted algae biomass was used for biogas production. The extracted oil composition was analyzed (saturated, monounsaturated and polyunsaturated fatty acids) and quantified. The highest lipid yields were obtained from Tetraselmis sp. (11%) and Scenedesmus almeriensis (10%), while the highest methane production from the lipid-exhausted algae biomass corresponded to Tetraselmis sp. (236mLCH4/gVSadded). Copyright © 2014 Elsevier Ltd. All rights reserved.

31 CFR 560.407 - Transactions related to Iranian-origin goods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... from third countries of goods containing Iranian-origin raw materials or components is not prohibited if those raw materials or components have been incorporated into manufactured products or... Iranian-origin raw materials or components are not prohibited if those raw materials or components have...

Thermophysical Property Models for Lunar Regolith

NASA Technical Reports Server (NTRS)

Schreiner, Samuel S.; Dominguez, Jesus A.; Sibille, Laurent; Hoffman, Jeffrey A.

2015-01-01

We present a set of models for a wide range of lunar regolith material properties. Data from the literature are t with regression models for the following regolith properties: composition, density, specific heat, thermal conductivity, electrical conductivity, optical absorption length, and latent heat of melting/fusion. These models contain both temperature and composition dependencies so that they can be tailored for a range of applications. These models can enable more consistent, informed analysis and design of lunar regolith processing hardware. Furthermore, these models can be utilized to further inform lunar geological simulations. In addition to regression models for each material property, the raw data is also presented to allow for further interpretation and fitting as necessary.

31 CFR 560.407 - Transactions related to Iranian-origin goods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... United States from third countries of goods containing Iranian-origin raw materials or components is not prohibited if those raw materials or components have been incorporated into manufactured products or... Iranian-origin raw materials or components are not prohibited if those raw materials or components have...

Biomediated continuous release phosphate fertilizer

DOEpatents

Goldstein, A.H.; Rogers, R.D.

1999-06-15

A composition is disclosed for providing phosphate fertilizer to the root zone of plants. The composition comprises a microorganism capable of producing and secreting a solubilization agent, a carbon source for providing raw material for the microorganism to convert into the solubilization agent, and rock phosphate ore for providing a source of insoluble phosphate that is solubilized by the solubilization agent and released as soluble phosphate. The composition is provided in a physical form, such as a granule, that retains the microorganism, carbon source, and rock phosphate ore, but permits water and soluble phosphate to diffuse into the soil. A method of using the composition for providing phosphate fertilizer to plants is also disclosed. 13 figs.

An Experimental Investigation of Transverse Tension Fatigue Characterization of IM6/3501-6 Composite Materials Using a Three-Point Bend Test

NASA Technical Reports Server (NTRS)

Peck, Ann W.

1998-01-01

As composites are introduced into more complex structures with out-of-plane loadings, a better understanding is needed of the out-of-plane, matrix-dominated failure mechanisms. This work investigates the transverse tension fatigue characteristics of IM6/3501 composite materials. To test the 90 degree laminae, a three-point bend test was chosen, potentially minimizing handling and gripping issues associated with tension tests. A finite element analysis was performed of a particular specimen configuration to investigate the influence of specimen size on the stress distribution for a three-point bend test. Static testing of 50 specimens of 9 different sized configurations produced a mean transverse tensile strength of 61.3 Mpa (8.0 ksi). The smallest configuration (10.2 mm wide, Span-to-thickness ratio of 3) consistently exhibited transverse tensile failures. A volume scale effect was difficult to discern due to the large scatter of the data. Static testing of 10 different specimens taken from a second panel produced a mean transverse tensile strength of 82.7 Mpa (12.0 ksi). Weibull parameterization of the data was possible, but due to variability in raw material and/or manufacturing, more replicates are needed for greater confidence. Three-point flex fatigue testing of the smallest configuration was performed on 59 specimens at various levels of the mean static transverse tensile strength using an R ratio of 0.1 and a frequency of 20 Hz. A great deal of scatter was seen in the data. The majority of specimens failed near the center loading roller. To determine whether the scatter in the fatigue data is due to variability in raw material and/or the manufacturing process, additional testing should be performed on panels manufactured from different sources.

Carbon Nanotubes for Human Space Flight

NASA Technical Reports Server (NTRS)

Scott, Carl D.; Files, Brad; Yowell, Leonard

2003-01-01

Single-wall carbon nanotubes offer the promise of a new class of revolutionary materials for space applications. The Carbon Nanotube Project at NASA Johnson Space Center has been actively researching this new technology by investigating nanotube production methods (arc, laser, and HiPCO) and gaining a comprehensive understanding of raw and purified material using a wide range of characterization techniques. After production and purification, single wall carbon nanotubes are processed into composites for the enhancement of mechanical, electrical, and thermal properties. This "cradle-to-grave" approach to nanotube composites has given our team unique insights into the impact of post-production processing and dispersion on the resulting material properties. We are applying our experience and lessons-learned to developing new approaches toward nanotube material characterization, structural composite fabrication, and are also making advances in developing thermal management materials and electrically conductive materials in various polymer-nanotube systems. Some initial work has also been conducted with the goal of using carbon nanotubes in the creation of new ceramic materials for high temperature applications in thermal protection systems. Human space flight applications such as advanced life support and fuel cell technologies are also being investigated. This discussion will focus on the variety of applications under investigation.

Cellulose extraction from orange peel using sulfite digestion reagents.

PubMed

Bicu, Ioan; Mustata, Fanica

2011-11-01

Orange peel (OP) was used as raw material for cellulose extraction. Two different pulping reagents were used, sodium sulfite and sodium metabisulfite. The effect of the main process parameters, sulfite agent dosage and reaction duration, on cellulose yield was investigated. A central composite rotatable design involving two variables at five levels and response surface methodology were used for the optimization of cellulose recovery. Other two invariable parameters were reaction temperature and hydromodulus. The optimum yields, referred to the weight of double extracted OP, were 40.4% and 45.2% for sodium sulfite and sodium metabisulfite digestions, respectively. The crude celluloses were bleached with hypochlorite and oxygen. The physicochemical characterization data of these cellulose materials indicate good levels of purity, low crystallinities, good whitenesses, good water retention and moderate molecular weights. According to these specific properties the recovered celluloses could be used as fillers, water absorbents, or as raw materials for cellulose derivatives. Copyright © 2011 Elsevier Ltd. All rights reserved.

Hydrothermal pre-treatment of rapeseed straw.

PubMed

Díaz, Manuel J; Cara, Cristóbal; Ruiz, Encarnación; Romero, Inmaculada; Moya, Manuel; Castro, Eulogio

2010-04-01

As a first step for ethanol production from alternative raw materials, rapeseed straw was studied for fermentable sugar production. Liquid hot water was used as a pre-treatment method and the influence of the main pre-treatment variables was assessed. Experimental design and response surface methodology were applied using pre-treatment temperature and process time as factors. The pretreated solids were further submitted to enzymatic hydrolysis and the corresponding yields were used as pre-treatment performance evaluation. Liquid fractions obtained from pre-treatment were also characterized in terms of sugars and no-sugar composition. A mathematical model describing pre-treatment effects is proposed. Results show that enzymatic hydrolysis yields near to 100% based on pretreated materials can be achieved at 210-220 degrees C for 30-50 min, equivalent to near 70% of glucose present in the raw material. According to the mathematical model, a softer pre-treatment at 193 degrees C for 27 min results in 65% of glucose and 39% of xylose available for fermentation. Copyright 2009 Elsevier Ltd. All rights reserved.

Enzymatic hydrolysis of pretreated waste paper--source of raw material for production of liquid biofuels.

PubMed

Brummer, Vladimir; Jurena, Tomas; Hlavacek, Viliam; Omelkova, Jirina; Bebar, Ladislav; Gabriel, Petr; Stehlik, Petr

2014-01-01

Enzymatic hydrolysis of waste paper is becoming a perspective way to obtain raw material for production of liquid biofuels. Reducing sugars solutions that arise from the process of saccharification are a precursors for following or simultaneous fermentation to ethanol. Different types of waste paper were evaluated, in terms of composition and usability, in order to select the appropriate type of the waste paper for the enzymatic hydrolysis process. Novozymes® enzymes NS50013 and NS50010 were used in a laboratory scale trials. Technological conditions, which seem to be the most suitable for hydrolysis after testing on cellulose pulp and filter paper, were applied to hydrolysis of widely available waste papers - offset paper, cardboard, recycled paper in two qualities, matte MYsol offset paper and for comparison again on model materials. The highest yields were achieved for the cardboard, which was further tested using various pretreatment combinations in purpose of increasing the hydrolysis yields. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of aqueous extract of soil-like substrate made from three different materials on seed germination and seedling growth of rice

NASA Astrophysics Data System (ADS)

Shao, Lingzhi; Fu, Yuming; Fu, Wenting; Yan, Min; Li, Leyuan; Liu, Hong

2014-03-01

Biologically processing rice and wheat straws into soil-like substrate (SLS) and then reusing them in plant cultivation system to achieve waste recycle is very crucially important in Bioregenerative life support system (BLSS). However, rice is a plant with strong allelopathic potential. It is not clear yet that what kinds of raw materials can be processed into proper SLS to grow rice in BLSS. Therefore, in this study, the aqueous extract of SLS made from three different materials including rice straw, wheat straw and rice-wheat straw mixture was utilized to investigate its effects on the seed germination and seedling growth of rice. The gradients of the extract concentrations (soil:water) were 1:3, 1:5, 1:9, and 1:15 with deionized water used as control. The effects of different types of SLS on seed germination and seedling vitality of rice were confirmed by analyzing the germination rate, seedling length, root length, the fresh weight and other indicants. In addition, based on the analysis towards pH, organic matter composition and other factors of the SLS as well as the chlorophyll, hormone content of rice, and the mechanism of the inhibition was speculated in order to explore the preventive methods of the phenomenon. Finally, the feasibility of cultivating rice on SLSs made from the raw materials mentioned above was evaluated and wheat raw was determined as the most appropriate material for growing rice.

Investigation of Mechanism of Action of Modifying Admixtures Based on Products of Petrochemical Synthesis on Concrete Structure

NASA Astrophysics Data System (ADS)

Tukhareli, V. D.; Tukhareli, A. V.; Cherednichenko, T. F.

2017-11-01

The creation of composite materials for generating structural elements with the desired properties has always been and still remains relevant. The basis of a modern concrete technology is the creation of a high-quality artificial stone characterized by low defectiveness and structure stability. Improving the quality of concrete compositions can be achieved by using chemical admixtures from local raw materials which is a very promising task of modern materials’ science for creation of a new generation of concretes. The new generation concretes are high-tech, high-quality, multicomponent concrete mixes and compositions with admixtures that preserve the required properties in service under all operating conditions. The growing complexity of concrete caused by systemic effects that allow you to control the structure formation at all stages of the technology ensures the obtaining of composites with "directional" quality, compositions, structure and properties. The possibility to use the organic fraction of oil refining as a multifunctional hydrophobic-plasticizing admixture in the effective cement concrete is examined.

SiO2/ZnO Composite Hollow Sub-Micron Fibers: Fabrication from Facile Single Capillary Electrospinning and Their Photoluminescence Properties.

PubMed

Song, Guanying; Li, Zhenjiang; Li, Kaihua; Zhang, Lina; Meng, Alan

2017-02-24

In this work, SiO2/ZnO composite hollow sub-micron fibers were fabricated by a facile single capillary electrospinning technique followed by calcination, using tetraethyl orthosilicate (TEOS), polyvinylpyrrolidone (PVP) and ZnO nanoparticles as raw materials. The characterization results of the scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) spectra indicated that the asprepared composite hollow fibers consisted of amorphous SiO2 and hexagonal wurtzite ZnO. The products revealed uniform tubular structure with outer diameters of 400-500 nm and wall thickness of 50-60 nm. The gases generated and the directional escaped mechanism was proposed to illustrate the formation of SiO2/ZnO composite hollow sub-micron fibers. Furthermore, a broad blue emission band was observed in the photoluminescence (PL) of SiO2/ZnO composite hollow sub-micron fibers, exhibiting great potential applications as blue light-emitting candidate materials.

Relation between quality and production cost for pure biodiesel bases on the mixes of raw materials

NASA Astrophysics Data System (ADS)

Tsanaktsidis, C. G.; Spinthiropoulos, K. G.; Guliyev, Fariz; Dimitriou, D.; Euthaltsidou, K.; Tzilantonis, G. T.

2016-08-01

Nowadays biodiesel has become more attractive because it is made from renewable resources. The main ingredients of industrial biodiesel are rap oil, sun oil, fat acid, olive oil cooked. In this study we verify that, the proportion of these components sets the qualitative composition and energy efficiency of the final product. Essential we link the raw materials (rap oil, sun oil, fat acid, olive oil cooked) used in the manufacture of industrial biodiesel the proportion of mixes, with the variation of physicochemical properties of biodiesel produced. According to the quantitative analysis we notice that the physiochemical properties which alter the value for example humidity, acidity, while a large number of physicochemical properties do not change their value depending on the ratio of raw materials in each mixture. The analysis of these changes seems that the presence of fat acids is negative for the quality of the mixture. From the analysis of the cost of the final mixtures that lower cost is achieved in the mixture was 10 and the highest cost was in the mixture 3. Based on a study of the cost of the mixtures can determine a basic relation between the quality and the cost of the final product.

Wet-preserved hemp fibreboard properties improvement with veneering

NASA Astrophysics Data System (ADS)

Kirilovs, E.; Kukle, S.; Gusovius, H.-J.

2015-03-01

The initial research describes a new type of fiber boards for the furniture interior design, developed in cooperation with ATB (Leibniz-Institute for Agricultural Engineering) by using a new method of raw materials preparation and specific production technologies of ATB. The main raw materials are aerobically aged hemp stalks. The samples are made of hemp chips with a long preservation time and fastened together with the UF glue. Specimens are 8 mm thick and correspond to a medium-density fiberboard, fitting standard EN622. Due to the fact that non-veneered material can be used only in non-load-bearing constructions, material improving technologies were studied, such as increase of board density, increase of glue percentage, partially substitution of wet-preserved hemp chips with a dry hemp and/or wooden chips to equalize moisture content of obtained mixture. The particular article describes how the new material is veneered with the oak veneer obtaining three-ply composite board with the improved mechanical properties that allows to use these boards in a load-bearing constructions. Tests are performed with the veneered material to determine such parameters as static bending strength (MOR), modulus of elasticity in static bending (MOE), swelling in thickness and hardness.

Chemical and mineralogical characterization of archaeologicam building materials from Seyitomer Hoyuk Kutahya, Turkey.

NASA Astrophysics Data System (ADS)

Bilgen, Nejat; Olgun, Asim

This paper focuses on the spectroscopic and thermal analysis of the archaeological samples of mortar and plaster from middle Bronze Age and Achaemenid period in Seyitömer Höyük. The composition of the samples was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and thermogravimetric thermal analysis (TG-DTA). The results showed that human used different types of raw materials in the preperation of the mortar and plaster in the Middle Bronze Age and Achaemenid period. The material used in middle Bronze Age contains muscovite whereas the material in Achaemenid period contains albite. Although, the chemical composition of the mortar and plaster used in the period were similar, the calcium content of the plaster is relatively higher than the one of the mortar indicating people's awareness of the binding properties of calcite.

A New Silarylene-Siloxane Monomeric Resin for Structural Composites: Cure-Chemistry Insight and Thermal Properties of the Cured Matrix

DTIC Science & Technology

2013-03-01

remain nonvolatile during the entire fiber-infusion process and curing operation. The resin must offer several days of storage life before the prepreg ...shipboard handling and in-flight cyclic loading. The raw materials for the new resin and the process for making and curing the prepreg must be affordable

Suitability of live and fire-killed small-diameter ponderosa and lodgepole pine trees for manufacturing a new structural wood composite

Treesearch

J.M. Linton; H.M. Barnes; R.D. Seale; P.D. Jones; E. Lowell; S.S. Hummel

2010-01-01

Finding alternative uses for raw material from small-diameter trees is a critical problem throughout the United States. In western states, a lack of markets for small-diameter ponderosa pine (Pinus ponderosa) and lodgepole pine (Pinus contorta ) can contribute to problems associated with overstocking. To test the feasibility of...

Engineering Analysis and Economic Evaluation of the Synthesis of Composite CuO/ZnO/ZrO2 Nanocatalyst

NASA Astrophysics Data System (ADS)

Nandiyanto, A. B. D.; Hayati, W. R.; Aziz, T. A.; Ragadhita, R.; Abdullah, A. G.; Widiaty, I.

2018-02-01

The purpose of this study was to evaluate the synthesis process of composite CuO/ZnO/ZrO2 (CZZ) nanocatalyst. The CZZ nanocatalyst is used as a catalyst in the hydrogenation reaction, which is used to convert harmful CO2 gas into liquid fuels such as methanol. In this study, CZZ produced using the sol-gel autocombustion method was selected as a model of the production procedure. The evaluation was conducted into two factors: engineering and economic analysis. Engineering analysis was analyzed based on the available apparatuses and raw materials in online web. Then, these data were used and compared with the mass balance approximation. The economic analysis was done using several economic parameters, including such as gross margin, internal rate return, payback period, cumulative net value, break even point (BEP), profitability index on sales to investment. Engineering analysis showed the present method can be applied using available apparatuses and raw materials in market. Economic analysis result confirmed that the present project is profitable. The analysis concluded that the present project for the production of CZZ nanocatalyst is prospective in small scale industry and profitable (by positive values in all economic parameters).

Characterization of industrial wastes as raw materials for Emulsified Modified Bitumen (EMB) formulation

NASA Astrophysics Data System (ADS)

Najib Razali, Mohd; Isa, Syarifah Nur Ezatie Mohd; Salehan, Noor Adilah Md; Musa, Musfafikri; Aziz, Mohd Aizudin Abd; Nour, Abdurahman Hamid; Yunus, Rosli Mohd

2018-04-01

This study was conducted to characterize industrial wastes for formulation of emulsified modified bitumen (EMB) in relation to their physical characteristic and elemental composition. This analysis will give information either raw materials from industrial wastes can be used for EMB formulation. Bitumen is produced from crude oil that is extracted from the ground which categorizes the crude oil as one of the non-renewable form of product. A vast environmental problem issues arises in Malaysia cause by the excessive manufacturing activity that lead to a miss-management of industrial waste has leads to the used of industrial waste in the EMB formulation. Industrial waste such as polystyrene, polyethylene and used automotive oil can be used as alternative to formulate bitumen. Then a suitable emulsifier needs to be added to produce the final product which is EMB. The emulsifier will yield a charge depends on its properties to bind the oily bitumen with water. Physical characteristic studies were performed by thermogravimetric Analysis (TGA), differential scanning calorimetry (DSC), flash point test, density rest and moisture content test. Fourier Transform Infrared Spectroscopy (FTIR) analysis was measured to determine the material’s molecular composition and structure.

[Quality of pastas supplemented with rice bran].

PubMed

Sangronis, E; Rebolledo, M A

1997-06-01

The objective of this research was to investigate the potential of using rice bran as an ingredient in pastas spaghetti type. Two of the pastas were made with semolina from durum as raw material, supplemented with 10 and 20% rice bran. The other two were made with granular flour and the same percentage of rice bran. Proximate composition of raw material was analyzed. Pastas were elaborated in a local industry. Composition, proximal, color, texture, and sensorial quality of pastas were determined. Protein content (13.9-15.0%), ash (1.47-3.09%) and dietary fiber (6.71-8.45%) of pastas increased according to the percentage of rice bran added. The hardest pastas were those elaborated with semolina from durum wheat and with a 10% of substitution. Also, they were the most yellow. The sensory panel found differences in quality among the pastas evaluated. Pastas with 10% rice bran had the best quality. The results demonstrated that is possible to elaborate pastas with 20% as maximum of rice bran resulting products with high protein, ash and dietetic fiber content, but some undesirable characteristics were given by the rice bran as white spots, wrinkles and color changes.

Laundry detergents: an overview.

PubMed

Bajpai, Divya; Tyagi, V K

2007-01-01

Nowadays laundry detergents are becoming increasingly popular as they can be metered automatically into the washing machine, impart softness, antistaticness, resiliency to fabrics, mild to eyes and skins and shows good dispersibility in water. Because it is consumed when it is used, the sale of laundry detergent is a rather large business. There are many different kinds or brands of laundry detergent sold, many of them claiming some special qualities as selling points. A Laundry detergent composition is a formulated mixture of raw materials that can be classified into different types based on their properties and function in the final product. The different classes of raw materials are surfactants, builders, bleaching agents, enzymes, and minors which remove dirt, stain, and soil from surfaces or textiles gave them pleasant feel and odour. The physico-chemical properties of surfactants make them suitable for laundry purposes. Laundry detergent has traditionally been a powdered or granular solid, but the use of liquid laundry detergents has gradually increased over the years, and these days use of liquid detergent equals or even exceeds use of solid detergent. This review paper describes the history, composition, types, mechanism, consumption, environmental effects and consumption of laundry detergents.

Fabrication and mechanical properties of aluminum composite reinforced with functionalized carbon nanotubes

NASA Astrophysics Data System (ADS)

Alavijeh, Elham Zamani; Kokhaei, Saeed; Dehghani, Kamran

2018-01-01

Composite aluminum alloy (5000 series) and multi-walled carbon nanotubes (MWCNTs) were made using mechanical alloying, cold press and sintering. The quality of interactions between Al powders and CNTs in the metal matrix composite has a significant effect on mechanical properties. Motivated from the properties of functionalized CNTs, the current study use this material rather than the raw type, because of its reactivity. Besides, a poly-vinyl-alcohol pre-mixing is done, the aim of which is to enhance mixing process. The functionalized carbon nanotubes ware made by chemically method through refluxing with nitric acid. By this method functional groups have been created on CNTs surfaces. 1% and 3% functionalized carbon nanotubes were manufactured using the aforementioned method. To provide unbiased comparisons, 1% and 3% with raw CNTs and pure aluminum is produced with same manner. The numerical experiments affirm the superiority of the functionalized carbon nano-tubes in terms of the relative density and hardness of nanocomposites. As a final activity, the Fourier transformation infrared spectroscopy and field emission scanning electron microscopy techniques were used to characterize the carbon nanotubes and the powders.

Enzymatic hydrolysis of potato pulp.

PubMed

Lesiecki, Mariusz; Białas, Wojciech; Lewandowicz, Grażyna

2012-01-01

Potato pulp constitutes a complicated system of four types of polysaccharides: cellulose, hemicellulose, pectin and starch. Its composition makes it a potential and attractive raw material for the production of the second generation bioethanol. The aim of this research project was to assess the usefulness of commercial enzymatic preparations for the hydrolysis of potato pulp and to evaluate the effectiveness of hydrolysates obtained in this way as raw materials for ethanol fermentation. Sterilised potato pulp was subjected to hydrolysis with commercial enzymatic preparations. The effectiveness of the preparations declared as active towards only one fraction of potato pulp (separate amylase, pectinase and cellulase activity) and mixtures of these preparations was analysed. The monomers content in hydrolysates was determined using HPLC method. The application of amylolytic enzymes for potato pulp hydrolysis resulted in the release of only 18% of raw material with glucose as the dominant (77%) constituent of the formed product. In addition, 16% galactose was also determined in it. The hydrolysis of the cellulose fraction yielded up to 35% raw material and the main constituents of the obtained hydrolysate were glucose (46%) and arabinose (40%). Simultaneous application of amylolytic, cellulolytic and pectinolytic enzymes turned out to be the most effective way of carrying out the process as its efficiency in this case reached 90%. The obtained hydrolysate contained 63% glucose, 25% arabinose and 12% other simple substances. The application of commercial enzymatic preparations made it possible to perform potato pulp hydrolysis with 90% effectiveness. This was achieved by the application of a complex of amylolytic, cellulolytic and pectinolytic enzymes and the hydrolysate obtained in this way contained, primarily, glucose making it a viable substrate for ethanol fermentation.

Production of alcohol from Jerusalem artichoke for gasoline additive. Proucavanje mogucnosti proizvodnje alkohola iz topinambura kao dodatka u benzin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pekic, B.; Kisgeci, J.

1984-01-01

Trials conducted in 1980 and 1981 on three soil types, chernozem (a rich soil), anthropogenized black sand (a medium-rich soil), and anthropogenized brown sand (a poor soil), showed that the Jerusalem artichoke was superior to conventional field crops (corn, sugarbeet, potato, and sorghum) regarding the yield of carbohydrates per unit area, especially when grown on the poor soil. The analyses of the technological properties of Jerusalem artichokes grown for two years in the experimental plots showed that the plant species is a quality raw material for the production of alcohol. From the aspect of alcohol production, the quality of themore » tested varieties of Jerusalem artichoke depended neither on soil quality nor on the delay in harvesting the crop after it reached technological maturity. The results of the study indicate that the alcohol production from Jerusalem artichokes would be more economic, i.e., more profitable, than the production from conventional raw materials. The study of the carbohydrate composition of Jerusalem artichoke tubers made it clear that besides alcohol production, Jerusalem artichokes are a good raw material for the production of high-fructose syrup and crystalline fructose. Since the interest in these products kept increasing in recent years, because of their exceptional characters, it is necessary to establish research programs to cover these field too. In the course of the study the authors came across some interesting literature data on the use of Jerusalem artichokes as a raw material for the production of high-fructose syrup and crystalline fructose. Some of the publication, i.e., those that might be useful in further research work, are appended to this study.« less

[Comparative studies on the material performances of natural bone-like apatite from different bone sources].

PubMed

Fan, Xiaoxia; Ren, Haohao; Chen, Shutian; Wang, Guangni; Deng, Tianyu; Chen, Xingtao; Yan, Yonggang

2014-04-01

The compressive strength of the original bone tissue was tested, based on the raw human thigh bone, bovine bone, pig bone and goat bone. The four different bone-like apatites were prepared by calcining the raw bones at 800 degrees C for 8 hours to remove organic components. The comparison of composition and structure of bone-like apatite from different bone sources was carried out with a composition and structure test. The results indicated that the compressive strength of goat bone was similar to that of human thigh bone, reached (135.00 +/- 7.84) MPa; Infrared spectrum (IR), X-ray diffraction (XRD) analysis results showed that the bone-like apatite from goat bone was much closer to the structure and phase composition of bone-like apatite of human bones. Inductively Coupled Plasma (ICP) test results showed that the content of trace elements of bone-like apatite from goat bone was closer to that of apatite of human bone. Energy Dispersive Spectrometer (EDS) results showed that the Ca/P value of bone-like apatite from goat bone was also close to that of human bone, ranged to 1.73 +/- 0.033. Scanning electron microscopy (SEM) patterns indicated that the macrographs of the apatite from human bone and that of goat bone were much similar to each other. Considering all the results above, it could be concluded that the goat bone-like apatite is much similar to that of human bone. It can be used as a potential natural bioceramic material in terms of material properties.

On-line analysis of bulk materials using pulsed neutron interrogation

NASA Astrophysics Data System (ADS)

Lebrun, P.; Tourneur, P. Le; Poumarede, B.; Möller, H.; Bach, P.

1999-06-01

On the basis of our joint experience in neutronics for SODERN and in cement plant engineering for KRUPP POLYSIUS, we have developed a new on-line bulk materials analyser for the cement industry. This equipment includes a pulsed neutron generator GENIE 16, some gamma ray and neutron detectors, specially designed electronics with high counting rate, software delivering the mean elemental composition of raw material, and adequate shielding. This material is transported through the equipment on a conveyor belt, the size of which is adapted to the requirements. This paper briefly describes the equipment and some results, as obtained in dynamic test from a demonstrator installed in Germany.

Evolution of thermoelectric performance for (Bi,Sb){sub 2}Te{sub 3} alloys from cutting waste powders to bulks with high figure of merit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fan, Xi'an, E-mail: groupfxa@163.com; Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081; School of Materials and Metallurgy, Wuhan University of Science and Technology, 947 Heping Road, Qingshan District, Wuhan 430081

Bi{sub 2}Te{sub 3} based cutting waste powders from cutting wafers were firstly selected as raw materials to prepare p-type Bi{sub 2}Te{sub 3} based thermoelectric (TE) materials. Through washing, reducing, composition correction, smelting and resistance pressing sintering (RPS) process, p-type (Bi,Sb){sub 2}Te{sub 3} alloy bulks with different nominal stoichiometries were successfully obtained. The evolution of microstructure and TE performance for (Bi,Sb){sub 2}Te{sub 3} alloys were investigated in detail. All evidences confirmed that most of contaminants from line cutting process such as cutting fluid and oxides of Bi, Sb or Te could be removed by washing, reducing and smelting process used inmore » this work. The carrier content and corresponding TE properties could be adjusted effectively by appropriate composition correction treatment. At lastly, a bulk with a nominal stoichiometry of Bi{sub 0.44}Sb{sub 1.56}Te{sub 3} was obtained and its' dimensionless figure of merit (ZT) was about 1.16 at 90 °C. The ZT values of Bi{sub 0.36}Sb{sub 1.64}Te{sub 3} and Bi{sub 0.4}Sb{sub 1.6}Te{sub 3} alloy bulks could also reach 0.98 and 1.08, respectively. Different from the conventional recycling technology such as hydrometallurgy extraction methods, the separation and extraction of beneficial elements such as Bi, Sb and Te did not need to be performed and the Bi{sub 2}Te{sub 3} based bulks with high TE properties could be directly obtained from the cutting waste powders. In addition, the recycling technology introduced here was green and more suitable for practical industrial application. It can improve material utilization and lower raw material costs of manufacturers. - Graphical abstract: Three kinds of typical morphologies for the fractographs: typical lamellar structure, agglomerated submicron-sized granules and dispersed cubic particles from the initial cutting waste powders. - Highlights: • Bi{sub 2}Te{sub 3} based wastes were directly selected as raw materials for TE alloys. • Contaminants from cutting fluid and oxides could be effectively removed. • Bulk Bi{sub 0.44}Sb{sub 1.56}Te{sub 3} with ZT of 1.16 was obtained from Bi{sub 2}Te{sub 3} based wastes. • Different from hydrometallurgy, the recycling method introduced here was green. • Directly recycling Bi{sub 2}Te{sub 3} wastes can lower raw material costs of manufacturers.« less

Mechanical recycling of continuous fiber-reinforced thermoplastic sheets

NASA Astrophysics Data System (ADS)

Moritzer, Elmar; Heiderich, Gilmar

2016-03-01

This contribution examines possible material recycling of offcuts generated during the production of continuous-fiber-reinforced composite sheets. These sheets consist of a polyamide 6 matrix and glass fiber fabric. In the initial step, the offcut is shredded to obtain particles; following that, the particles are processed in a twin-screw process to produce fiber-reinforced plastic pellets with varying fiber contents. These pellets are intended for use in injection molding processes as a substitution for new raw materials. This investigation centers on the mechanical properties which can be achieved with the recycled material after both the twin-screw process and injection molding.

Spectral analysis of pharmaceutical formulations prepared according to ancient recipes in comparison with old museum remains.

PubMed

Gamberini, M Cristina; Baraldi, C; Freguglia, G; Baraldi, P

2011-10-01

A study of the composition of the remains of ancient ointments from museums was undertaken to enable understanding of the preparation techniques. Comparison of ancient recipes from different historical periods and spectroscopic characteristics of inorganic and/or organic remains recovered in museum vessels enabled preparation of ancient pharmaceutical-cosmetic formulations. Farmacopea Augustana by Occo was one the most important books studied for the 14 formulations prepared in the laboratory. Three formulations are discussed in detail and raw materials and new preparations were proposed for ozone ageing. The most important micro Raman results are discussed. The spectra of the raw materials lipids, beeswax, and resins are discussed; beeswax and pig suet (axŭngia) Raman spectra were found to be similar, but different from those of the aged oils. SERS was applied to ancient ointments and galbanum and the Raman spectra are reported and discussed for the first time.

Quantification of cell response to polymeric composites using a two-dimensional gradient platform.

PubMed

Lin, Nancy J; Hu, Haiqing; Sung, Lipin; Lin-Gibson, Sheng

2009-07-01

A simple and straightforward screening process to assess the toxicity and corresponding cell response of dental composites would be useful prior to extensive in vitro or in vivo characterization. To this end, gradient composite samples were prepared with variations in filler content/type and in degree of conversion (DC). The DC was determined using near infrared spectroscopy (NIR), and the surface morphology was evaluated by laser scanning confocal microscopy (LSCM). RAW 264.7 macrophage-like cells were cultured directly on the composite gradient samples, and cell viability, density, and area were measured at 24 h. All three measures of cell response varied as a function of material properties. For instance, compositions with higher filler content had no reduction in cell viability or cell density, even at low conversions of 52%, whereas significant decreases in viability and density were present when the filler content was 35% or below (by mass). The overall results demonstrate the complexity of the cell-material interactions, with properties including DC, filler type, filler mass ratio, and surface morphology influencing the cell response. The combinatorial approach described herein enables simultaneous screening of multiple compositions and material properties, providing a more thorough characterization of cell response for the improved selection of biocompatible composite formulations and processing conditions.

The study about the use of the natural fibres in composite materials

NASA Astrophysics Data System (ADS)

Hristian, L.; Ostafe, M. M.; Manea, L. R.; Leon, A. L.

2016-08-01

The current technological development, the crises of raw materials and energy, the increased aggression towards the environment have led to the development of the new materials and unconventional technologies. The composite materials have both many important advantages compared to the traditional materials and provide many functional advantages: low weight, mechanical resistance, low maintenance costs. The main advantage of the composites lies in their ability to combine the physical properties of components to achieve new structural functionalities, so the modulation of the properties and finally, to obtain a wide variety of materials which may be used in all areas of activities. Some biodegradable fibers, flax, hemp, may provide the specific mechanical properties compared to those of the glass fiber, due to their high strength and low density of their volume. To make the right choice, even if the natural fibers have very low power consumption compared with the synthetic fibers, such as glass or carbon, it should be considered a careful assessment of the environmental impact. The present study shows that the validity of the replacement of the synthetic fibers with natural fibers, depends on the reinforcement type and the complexity of the problems due to the processing of natural fibers.

40 CFR 63.1343 - What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker piles?

Code of Federal Regulations, 2011 CFR

2011-07-01

..., clinker coolers, raw material dryers, and open clinker piles? 63.1343 Section 63.1343 Protection of... What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker piles? (a..., clinker cooler, and raw material dryer. All dioxin D/F, HCl, and total hydrocarbon (THC) emission limits...

26 CFR 1.472-1 - Last-in, first-out inventories.

Code of Federal Regulations, 2011 CFR

2011-04-01

... may elect to have such method apply to the raw materials only (including those included in goods in... adjustments are confined to costs of the raw material in the inventory and the cost of the raw material in... that the opening inventory had 10 units of raw material, 10 units of goods in process, and 10 units of...

40 CFR 63.1343 - What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker storage...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., clinker coolers, raw material dryers, and open clinker storage piles? 63.1343 Section 63.1343 Protection... Limits § 63.1343 What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker... associated with that kiln, clinker cooler, raw material dryer, and open clinker storage pile. All D/F, HCl...

40 CFR 63.1343 - What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker storage...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., clinker coolers, raw material dryers, and open clinker storage piles? 63.1343 Section 63.1343 Protection... Limits § 63.1343 What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker... associated with that kiln, clinker cooler, raw material dryer, and open clinker storage pile. All D/F, HCl...

40 CFR 63.1343 - What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker piles?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., clinker coolers, raw material dryers, and open clinker piles? 63.1343 Section 63.1343 Protection of... What standards apply to my kilns, clinker coolers, raw material dryers, and open clinker piles? (a..., clinker cooler, and raw material dryer. All dioxin D/F, HCl, and total hydrocarbon (THC) emission limits...

26 CFR 1.472-1 - Last-in, first-out inventories.

Code of Federal Regulations, 2014 CFR

2014-04-01

... may elect to have such method apply to the raw materials only (including those included in goods in... adjustments are confined to costs of the raw material in the inventory and the cost of the raw material in... that the opening inventory had 10 units of raw material, 10 units of goods in process, and 10 units of...

26 CFR 1.472-1 - Last-in, first-out inventories.

Code of Federal Regulations, 2013 CFR

2013-04-01

... may elect to have such method apply to the raw materials only (including those included in goods in... adjustments are confined to costs of the raw material in the inventory and the cost of the raw material in... that the opening inventory had 10 units of raw material, 10 units of goods in process, and 10 units of...

26 CFR 1.472-1 - Last-in, first-out inventories.

Code of Federal Regulations, 2012 CFR

2012-04-01

... may elect to have such method apply to the raw materials only (including those included in goods in... adjustments are confined to costs of the raw material in the inventory and the cost of the raw material in... that the opening inventory had 10 units of raw material, 10 units of goods in process, and 10 units of...

[Which one is more important, raw materials or productive technology?--a case study for quality consistency control of Gegen Qinlian decoction].

PubMed

Zhong, Wen; Chen, Sha; Zhang, Jun; Wang, Yu-Sheng; Liu, An

2016-03-01

To investigate the effect of Chinese medicine raw materials and production technology on quality consistency of Chinese patent medicines with Gegen Qinlian decoction as an example, and establish a suitable method for the quality consistency control of Chinese patent medicines. The results showed that the effect of production technology on the quality consistency was generally not more than 5%, while the effect of raw materials was even more than 30%, indicating that the effect of raw materials was much greater than that of the production technology. In this study, blend technology was used to improve the quality consistency of raw materials. As a result, the difference between the product produced by raw materials and reference groups was less than 5%, thus increasing the quality consistence of finished products. The results showed that under the current circumstances, the main factor affecting the quality consistency of Chinese patent medicines was raw materials, so we shall pay more attention to the quality of Chinese medicine's raw materials. Finally, a blend technology can improve the quality consistency of Chinese patent medicines. Copyright© by the Chinese Pharmaceutical Association.

21 CFR 1304.31 - Reports from manufacturers importing narcotic raw material.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Reports from manufacturers importing narcotic raw... RECORDS AND REPORTS OF REGISTRANTS Reports § 1304.31 Reports from manufacturers importing narcotic raw material. (a) Every manufacturer which imports or manufactures from narcotic raw material (opium, poppy...

21 CFR 1304.31 - Reports from manufacturers importing narcotic raw material.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 9 2011-04-01 2011-04-01 false Reports from manufacturers importing narcotic raw... RECORDS AND REPORTS OF REGISTRANTS Reports § 1304.31 Reports from manufacturers importing narcotic raw material. (a) Every manufacturer which imports or manufactures from narcotic raw material (opium, poppy...

Innovative hyperspectral imaging (HSI) based techniques applied to end-of-life concrete drill core characterization for optimal dismantling and materials recovery

NASA Astrophysics Data System (ADS)

Bonifazi, Giuseppe; Picone, Nicoletta; Serranti, Silvia

2015-02-01

The reduction of EOL concrete disposal in landfills, together with a lower exploitation of primary raw materials, generates a strong interest to develop, set-up and apply innovative technologies to maximize Construction and Demolition Waste (C&DW) conversion into useful secondary raw materials. Such a goal can be reached starting from a punctual in-situ efficient characterization of the objects to dismantle in order to develop demolition actions aimed to set up innovative mechanical-physical processes to recover the different materials and products to recycle. In this paper an innovative recycling-oriented characterization strategy based on HyperSpectral Imaging (HSI) is described in order to identify aggregates and mortar in drill core samples from end-of-life concrete. To reach this goal, concrete drill cores from a demolition site were systematically investigated by HSI in the short wave infrared field (1000-2500 nm). Results obtained by the adoption of the HSI approach showed as this technology can be successfully applied to analyze quality and characteristics of C&DW before dismantling and as final product to reutilise after demolition-milling-classification actions. The proposed technique and the related recognition logics, through the spectral signature detection of finite physical domains (i.e. concrete slice and/or particle) of different nature and composition, allows; i) to develop characterization procedures able to quantitatively assess end-of-life concrete compositional/textural characteristics and ii) to set up innovative sorting strategies to qualify the different materials constituting drill core samples.

Applications of a synergic analytical strategy to figure out technologies in medieval glazed pottery with "negative decoration" from Italy

NASA Astrophysics Data System (ADS)

Giannossa, Lorena Carla; Acquaviva, Marianna; Laganara, Caterina; Laviano, Rocco; Mangone, Annarosa

2014-09-01

Glazed pottery with "negative decoration" samples, dating back to the twelfth to thirteenth century ad and coming from three sites along the Adriatic coast, Siponto, Egnatia and Trani (Southern Italy) were characterized from physical-chemical, mineralogical and morphological points of view. Optical microscopy, scanning electron microscopy with energy dispersive X-ray spectroscopy, inductively coupled plasma-mass spectroscopy, X-ray diffraction and micro-Raman spectroscopy investigations were carried out on ceramic bodies, pigments and glazes of the fragments. We aimed to outline the technological features, define the nature of decorations and coatings—glazes and engobes—and look for clues to hypothesize provenance. Results obtained show clear differences in raw materials and production technology between the impressed ceramic of Islamic tradition and the incised one of Byzantine tradition. Regarding the latter, evidences of a non-local origin can be found in the compositional diversity of raw materials used for the ceramic bodies of fragments decorated with spiral and pseudo-kufic motifs, which stressed the use of clays so far not recorded in Apulia. At the same time, at least in the case of Siponto, the compositional similarity of both ceramic bodies and materials used under the glaze for impressed ceramic and painted polychrome ceramics (RMR and protomaiolica), more likely local production, could suggest that both were produced in the same workshops.

An on-belt elemental analyser for the cement industry.

PubMed

Lim, C S; Tickner, J R; Sowerby, B D; Abernethy, D A; McEwan, A J; Rainey, S; Stevens, R; Manias, C; Retallack, D

2001-01-01

On-line control of raw mill feed composition is a key factor in the improved control of cement plants. A new and improved on-conveyor belt elemental analyser for cement raw mill feed based on neutron inelastic scatter and capture techniques has been developed and tested successfully in Adelaide Brighton's Birkenhead cement plant on highly segregated material with a depth range of 100 to 180 mm. Dynamic tests in the plant have shown analyser RMS total errors of 0.49, 0.52, 0.38 and 0.23 wt% (on a loss free basis) for CaO, SiO2, Al2O3 and Fe2O3 respectively, when 10-minute counting periods are used.

High-Throughput Fabrication Method for Producing a Silver-Nanoparticles-Doped Nanoclay Polymer Composite with Novel Synergistic Antibacterial Effects at the Material Interface.

PubMed

Cai, Shaobo; Pourdeyhimi, Behnam; Loboa, Elizabeth G

2017-06-28

In this study, we report a high-throughput fabrication method at industrial pilot scale to produce a silver-nanoparticles-doped nanoclay-polylactic acid composite with a novel synergistic antibacterial effect. The obtained nanocomposite has a significantly lower affinity for bacterial adhesion, allowing the loading amount of silver nanoparticles to be tremendously reduced while maintaining satisfactory antibacterial efficacy at the material interface. This is a great advantage for many antibacterial applications in which cost is a consideration. Furthermore, unlike previously reported methods that require additional chemical reduction processes to produce the silver-nanoparticles-doped nanoclay, an in situ preparation method was developed in which silver nanoparticles were created simultaneously during the composite fabrication process by thermal reduction. This is the first report to show that altered material surface submicron structures created with the loading of nanoclay enables the creation of a nanocomposite with significantly lower affinity for bacterial adhesion. This study provides a promising scalable approach to produce antibacterial polymeric products with minimal changes to industry standard equipment, fabrication processes, or raw material input cost.

The use of fractionated fly ash of thermal power plants as binder for production of briquettes of coke breeze and dust

NASA Astrophysics Data System (ADS)

Temnikova, E. Yu; Bogomolov, A. R.; Lapin, A. A.

2017-11-01

In this paper, we propose to use the slag and ash material of thermal power plants (TPP) operating on pulverized coal fuel. The elemental and chemical composition of fly ash of five Kuzbass thermal power plants differs insignificantly from the composition of the mineral part of coking coal because coke production uses a charge, whose composition defines the main task: obtaining coke with the required parameters for production of iron and steel. These indicators are as follows: CRI reactivity and strength of the coke residue after reaction with CO2 - CSR. The chemical composition of fly ash of thermal power plants and microsilica with bulk density of 0.3-0.6 t/m3 generated at production of ferroalloys was compared. Fly ash and microsilica are the valuable raw material for production of mineral binder in manufacturing coke breeze briquettes (fraction of 2-10 mm) and dust (0-200 μm), generated in large quantities during coking (up to 40wt%). It is shown that this binder is necessary for production of smokeless briquettes with low reactivity, high strength and cost, demanded for production of cupola iron and melting the silicate materials, basaltic rocks in low-shaft furnaces. It is determined that microsilica contains up to 90% of silicon oxide, and fly ash contains up to 60% of silicon oxide and aluminum oxide of up to 20%. On average, the rest of fly ash composition consists of basic oxides. According to calculation by the VUKHIN formula, the basicity index of briquette changes significantly, when fly ash is introduced into briquette raw material component as a binder. The technology of coke briquette production on the basis of the non-magnetic fraction of TPP fly ash in the ratio from 3.5:1 to 4.5:1 (coke breeze : coke dust) with the addition of the binder component to 10% is proposed. The produced briquettes meet the requirements by CRI and require further study on CSR requirements.

Preparation of conductive paper composites based on natural cellulosic fibers for packaging applications.

PubMed

Youssef, Ahmed M; El-Samahy, Magda Ali; Abdel Rehim, Mona H

2012-08-01

Conducting paper based on natural cellulosic fibers and conductive polymers was prepared using unbleached bagasse and/or rice straw fibers (as cellulosic raw materials) and polyaniline (PANi) as conducting polymer. These composites were synthesized by in situ emulsion polymerization using ammonium persulfate (APS) as oxidant in the presence of dodecylbenzene sulfonic acid (DBSA) as emulsifier. The prepared composites were characterized using Fourier transform infrared (FTIR), thermal gravimetric analysis (TGA), differential scanning calorimeter (DSC), and their morphology was investigated using scanning electron microscope (SEM). Electrical conductivity measurements showed that the conductivity of the paper sheets increases by increasing the ratio of PANi in the composite. Mechanical properties of the paper sheets were also investigated, the results revealed that the values of breaking length, burst factor, and tear factor are decreased with increasing ratio of added PANi, and this effect is more pronounced in bagasse-based composites. The new conductive composites can have potential use as anti-static packaging material or anti-bacterial paper for packaging applications. Copyright © 2012 Elsevier Ltd. All rights reserved.

The effect of activation agent on surface morphology, density and porosity of palm shell and coconut shell activated carbon

NASA Astrophysics Data System (ADS)

Leman, A. M.; Zakaria, S.; Salleh, M. N. M.; Sunar, N. M.; Feriyanto, D.; Nazri, A. A.

2017-09-01

Activated carbon (AC) has one of the promising alternative technology for filtration and adsorption process. It inexpensive material because the sources is abundant especially in Malaysia. Main purpose of this project is to develop AC by chemical activation process to improve adsorption capacity by improving porosity of AC. AC developed via carbonization using designed burner at temperature of 650°C to 850 °C and activated by Potassium Hydroxide (KOH) in 12 hour and then dried at temperature of 300°C. Characterization and analysis is conducted by Scanning Electron Microscopy (SEM) for surface morphology analysis, Energy Dispersive Spectroscopy (EDS) for composition analysis, density and porosity analysis. Results shows that uneven surface has been observed both of AC and non-AC and also AC shows higher porosity as compared to non-AC materials. Density value of raw material has lower than AC up to 11.67% and 47.54% and porosity of raw material has higher than AC up to 31.45% and 45.69% for palm shell and coconut shell AC. It can be concluded that lower density represent higher porosity of material and higher porosity indicated higher adsorption capacity as well.

Characterization of refractory brick based on local raw material from Lampung Province - Indonesia

NASA Astrophysics Data System (ADS)

Amin, Muhammad; Suryana, Yayat I.; Isnugroho, Kusno; Aji, Bramantyo B.; Birawidha, David C.; Hendronursito, Yusup

2018-04-01

Refractories are non-metallic inorganic materials that are difficult to melt at high temperatures and used in high-temperature casting industries. Refractories are classified into their constituent mineral feed stocks, refractories having typical plot properties commonly called fire bricks. In the manufacture of refractory bricks that exist in the market during the use of mangrove materials derived from abroad that is from China. In this research the refractory brick materials used are quartz sand, feldspart, kaolin, bentonite, and ball clay. All materials come from local Lampung Province - Indonesia. The experiment, there are 7 kinds of experimental composition, made of plot shape with size 230 mm, 65 mm in thickness, 114 mm height mould using manual press machine with 10 tons power and burning at 1400°C for 5 hours. Refractory brick product is done by physical test in the form of porosity, specific gravity, compressive strength and XRF and SEM characteristics. The result of XRF characteristic of refractory brick composition of 1 to 5 compared to the refractory brick type SK 34 in the market and the result of composition 1 is a composition close to refractory brick composition type SK 34 namely SiO2 is 54.21 %, Al2O3 is 25.38 % and test Physical of Bulk density is 2.25 g/cm3, porosity is 18.98 % and compressive strength is 325 kg/cm2.

Extraction of cellulose microcrystalline from galam wood for biopolymer

NASA Astrophysics Data System (ADS)

Ismail, Ika; Sa'adiyah, Devy; Rahajeng, Putri; Suprayitno, Abdi; Andiana, Rocky

2018-04-01

Consumption of plastic raw materials tends to increase, but until now the meet of the consumption of plastic raw are still low, even some are still imported. Nowadays, Indonesia's plastic needs are supported by petrochemicals where raw materials are still dependent abroad and petropolymer raw materials are derived from petroleum which will soon be depleted due to rising petroleum needs. Therefore, various studies have been conducted to develop natural fiber-based polymers that are biodegradable and abundant in nature. It is because the natural polymer production process is very efficient and very environmentally friendly. There have been many studies of biopolymers especially natural fiber-based polymers from plants, due to plants containing cellulose, hemicellulose and lignin. However, cellulose is the only one who has crystalline structures. Cellulose has a high crystality compared to amorphous lignin and hemicellulose. In this study, extracted cellulose as biopolymer and amplifier on composite. The cellulose is extracted from galam wood from East Kalimantan. Cellulose extraction will be obtained in nano / micro form through chemical and mechanical treatment processes. The chemical treatment of cellulose extraction is alkalinization process using NaOH solution, bleaching using NaClO2 and acid hydrolysis using sulfuric acid. After chemical treatment, ultrasonic mechanical treatment is made to make cellulose fibers into micro or nano size. Besides, cellulose results will be characterized. Characterization was performed to analyze molecules of cellulose compounds extracted from plants using Fourier Transformation Infra Red (FTIR) testing. XRD testing to analyze cellulose crystallinity. Scanning Electron Microscope (SEM) test to analyze morphology and fiber size.

A high-performance ternary Si composite anode material with crystal graphite core and amorphous carbon shell

NASA Astrophysics Data System (ADS)

Sui, Dong; Xie, Yuqing; Zhao, Weimin; Zhang, Hongtao; Zhou, Ying; Qin, Xiting; Ma, Yanfeng; Yang, Yong; Chen, Yongsheng

2018-04-01

Si is a promising anode material for lithium-ion batteries, but suffers from sophisticated engineering structures and complex fabrication processes that pose challenges for commercial application. Herein, a ternary Si/graphite/pyrolytic carbon (SiGC) anode material with a structure of crystal core and amorphous shell using low-cost raw materials is developed. In this ternary SiGC composite, Si component exists as nanoparticles and is spread on the surface of the core graphite flakes while the sucrose-derived pyrolytic carbon further covers the graphite/Si components as the amorphous shell. With this structure, Si together with the graphite contributes to the high specific capacity of this Si ternary material. Also the graphite serves as the supporting and conducting matrix and the amorphous shell carbon could accommodate the volume change effect of Si, reinforces the integrity of the composite architecture, and prevents the graphite and Si from direct exposing to the electrolyte. The optimized ternary SiGC composite displays high reversible specific capacity of 818 mAh g-1 at 0.1 A g-1, initial Coulombic efficiency (CE) over 80%, and excellent cycling stability at 0.5 A g-1 with 83.6% capacity retention (∼610 mAh g-1) after 300 cycles.

29 CFR 779.333 - Goods sold for use as raw materials in other products.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 3 2011-07-01 2011-07-01 false Goods sold for use as raw materials in other products. 779... Service Establishments Sales Not Made for Resale § 779.333 Goods sold for use as raw materials in other products. Goods are sold for resale where they are sold for use as a raw material in the production of a...

29 CFR 779.333 - Goods sold for use as raw materials in other products.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Goods sold for use as raw materials in other products. 779... Service Establishments Sales Not Made for Resale § 779.333 Goods sold for use as raw materials in other products. Goods are sold for resale where they are sold for use as a raw material in the production of a...

40 CFR Table N-1 to Subpart N of... - CO2 Emission Factors for Carbonate-Based Raw Materials

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Based Raw Materials N Table N-1 to Subpart N of Part 98 Protection of Environment ENVIRONMENTAL... Raw Materials Carbonate-basedraw material—mineral CO2 emission factor a Limestone—CaCO3 0.440 Dolomite... in units of metric tons of CO2 emitted per metric ton of carbonate-based raw material charged to the...

40 CFR 63.1346 - Standards for new or reconstructed raw material dryers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for new or reconstructed raw... Industry Emission Standards and Operating Limits § 63.1346 Standards for new or reconstructed raw material dryers. (a) New or reconstructed raw material dryers located at facilities that are major sources can not...

Leveraging “Raw Materials” as Building Blocks and Bioactive Signals in Regenerative Medicine

PubMed Central

Renth, Amanda N.

2012-01-01

Components found within the extracellular matrix (ECM) have emerged as an essential subset of biomaterials for tissue engineering scaffolds. Collagen, glycosaminoglycans, bioceramics, and ECM-based matrices are the main categories of “raw materials” used in a wide variety of tissue engineering strategies. The advantages of raw materials include their inherent ability to create a microenvironment that contains physical, chemical, and mechanical cues similar to native tissue, which prove unmatched by synthetic biomaterials alone. Moreover, these raw materials provide a head start in the regeneration of tissues by providing building blocks to be bioresorbed and incorporated into the tissue as opposed to being biodegraded into waste products and removed. This article reviews the strategies and applications of employing raw materials as components of tissue engineering constructs. Utilizing raw materials holds the potential to provide both a scaffold and a signal, perhaps even without the addition of exogenous growth factors or cytokines. Raw materials contain endogenous proteins that may also help to improve the translational success of tissue engineering solutions to progress from laboratory bench to clinical therapies. Traditionally, the tissue engineering triad has included cells, signals, and materials. Whether raw materials represent their own new paradigm or are categorized as a bridge between signals and materials, it is clear that they have emerged as a leading strategy in regenerative medicine. The common use of raw materials in commercial products as well as their growing presence in the research community speak to their potential. However, there has heretofore not been a coordinated or organized effort to classify these approaches, and as such we recommend that the use of raw materials be introduced into the collective consciousness of our field as a recognized classification of regenerative medicine strategies. PMID:22462759

Longitudial variation in wood specific gravity of planted loblolly pine in the southern United States

Treesearch

Finto Antony; Laurence R. Schimleck; Richard F. Daniels; Alexander Clark

2012-01-01

Loblolly pine (Pinus taeda L.) is the most important plantation species grown in the southern United States, having more than half of the standing pine volume. Wood from loblolly pine is a principal source of raw material for the pulp and paper industry and is desirable for the production of lumber and composite wood products. The quality of wood...

Investigations of the mechanical properties of bi-layer and trilayer fiber reinforced composites

NASA Astrophysics Data System (ADS)

Jayakrishna, K.; Balasubramani, K.; Sultan, M. T. H.; Karthikeyan, S.

2016-10-01

Natural fibers are renewable raw materials with an environmental-friendly properties and they are recyclable. The mechanical properties of bi-layer and tri-layer thermoset polymer composites have been analyzed. The bi-layer composite consists of basalt and jute mats, while the tri-layer composite consists of basalt fiber, jute fiber and glass fiber mats. In both cases, the epoxy resin was used as the matrix and PTFE as a filler in the composites. The developed trilayer natural fiber composite can be used in various industrial applications such as automobile parts, construction and manufacturing. Furthermore, it also can be adopted in aircraft interior decoration and designed body parts. Flexural, impact, tensile, compression, shear and hardness tests, together with density measurement, were conducted to study the mechanical properties of both bi-layer and tri-layer composites. From the comparison, the tri-layer composite was found to perform in a better way in all tests.

Sapropel as a Binder: Properties and Application Possibilities for Composite Materials

NASA Astrophysics Data System (ADS)

Obuka, V.; Šinka, M.; Kļaviņš, M.; Stankeviča, K.; Korjakins, A.

2015-11-01

Recent development trends largely look for possibilities of a wider use of natural materials and local resources. In this perspective, the use of organic rich lake sediment - sapropel - as a binding material in line with other environmentally friendly filling materials can be considered as a challenge. Sapropel itself is a valuable resource with multiple areas of application, for example, medicine, veterinary, agriculture, livestock farming, balneology, cosmetic applications, construction, and its application options have been widely studied in the 20th century in the Baltic countries, Ukraine and Russia. Birch wood fibre and sanding dust, hemp shives, ‘Aerosil’ are used as a filler and three types of sapropel are used as a binder in making composites. After material preparation and curing, physical and mechanical properties - density, thermal conductivity, compressive and flexural strength, were determined and compared to the data in the literature, and the opportunities to use them in the ecological construction were considered. The obtained results give insight into possibilities to use sapropel as a raw material, which can be considered as prospective material for construction materials and design products.

Statistical Analyses of Raw Material Data for MTM45-1/CF7442A-36% RW: CMH Cure Cycle

NASA Technical Reports Server (NTRS)

Coroneos, Rula; Pai, Shantaram, S.; Murthy, Pappu

2013-01-01

This report describes statistical characterization of physical properties of the composite material system MTM45-1/CF7442A, which has been tested and is currently being considered for use on spacecraft structures. This composite system is made of 6K plain weave graphite fibers in a highly toughened resin system. This report summarizes the distribution types and statistical details of the tests and the conditions for the experimental data generated. These distributions will be used in multivariate regression analyses to help determine material and design allowables for similar material systems and to establish a procedure for other material systems. Additionally, these distributions will be used in future probabilistic analyses of spacecraft structures. The specific properties that are characterized are the ultimate strength, modulus, and Poisson??s ratio by using a commercially available statistical package. Results are displayed using graphical and semigraphical methods and are included in the accompanying appendixes.

Scoping Future Policy Dynamics in Raw Materials Through Scenarios Testing

NASA Astrophysics Data System (ADS)

Correia, Vitor; Keane, Christopher; Sturm, Flavius; Schimpf, Sven; Bodo, Balazs

2017-04-01

The International Raw Materials Observatory (INTRAW) project is working towards a sustainable future for the European Union in access to raw materials, from an availability, economical, and environmental framework. One of the major exercises for the INTRAW project is the evaluation of potential future scenarios for 2050 to frame economic, research, and environmental policy towards a sustainable raw materials supply. The INTRAW consortium developed three possible future scenarios that encompass defined regimes of political, economic, and technological norms. The first scenario, "Unlimited Trade," reflects a world in which free trade continues to dominate the global political and economic environment, with expectations of a growing demand for raw materials from widely distributed global growth. The "National Walls" scenario reflects a world where nationalism and economic protectionism begins to dominate, leading to stagnating economic growth and uneven dynamics in raw materials supply and demand. The final scenario, "Sustainability Alliance," examines the dynamics of a global political and economic climate that is focused on environmental and economic sustainability, leading towards increasingly towards a circular raw materials economy. These scenarios were reviewed, tested, and provided simulations of impacts with members of the Consortium and a panel of global experts on international raw materials issues which led to expected end conditions for 2050. Given the current uncertainty in global politics, these scenarios are informative to identifying likely opportunities and crises. The details of these simulations and expected responses to the research demand, technology investments, and economic components of raw materials system will be discussed.

Occurrence and antimicrobial resistance of pathogenic Escherichia coli and Salmonella spp. in retail raw table eggs sold for human consumption in Enugu state, Nigeria

PubMed Central

Okorie-Kanu, O. Josephine; Ezenduka, E. Vivienne; Okorie-Kanu, C. Onwuchokwe; Ugwu, L. Chinweokwu; Nnamani, U. John

2016-01-01

Aim: This study was conducted to investigate the occurrence of pathogenic Escherichia coli and Salmonella species in retail raw table eggs sold for human consumption in Enugu State and to determine the resistance of these pathogens to antimicrobials commonly used in human and veterinary practices in Nigeria. Materials and Methods: A total of 340 raw table eggs comprising 68 composite samples (5 eggs per composite sample) were collected from five selected farms (13 composite samples from the farms) and 10 retail outlets (55 composite samples from the retail outlets) in the study area over a period of 4-month (March-June, 2014). The eggs were screened for pathogenic E. coli and Salmonella species following standard procedures within 24 h of sample collection. Isolates obtained were subjected to in-vitro antimicrobial susceptibility test with 15 commonly used antimicrobials using the disk diffusion method. Results: About 37 (54.4%) and 7 (10.3%) of the 68 composite samples were positive for pathogenic E. coli and Salmonella species, respectively. The shells showed significantly higher (p<0.05) contaminations than the contents for both microorganisms. The eggs from the farms showed higher contamination with pathogenic E. coli than eggs from the retail outlets while the reverse was the case for Salmonella species even though they were not significant (p>0.05). The organisms obtained showed a multiple drug resistance. They were completely resistant to nitrofurantoin, sulfamethoxazole/trimethoprim, penicillin G and oxacillin. In addition to these, Salmonella spp. also showed 100% resistance to tetracycline. The pathogenic E. coli isolates obtained were 100% susceptible to gentamicin, neomycin, ciprofloxacin, and amoxicillin-clavulanic acid while Salmonella spp. showed 100% susceptibility to erythromycin, neomycin, and rifampicin. Both organisms showed varying degrees of resistance to streptomycin, amoxicillin, vancomycin, and doxycycline. Conclusion: From the results of the study, it can be concluded that the raw table eggs marketed for human consumption in Enugu State, Nigeria is contaminated with pathogenic E. coli and Salmonella species that showed multiple drug resistance to antimicrobial agents commonly used in veterinary and human practice. PMID:27956787

Intermetallics as innovative CRM-free materials

NASA Astrophysics Data System (ADS)

Novák, Pavel; Jaworska, Lucyna; Cabibbo, Marcello

2018-03-01

Many of currently used technical materials cannot be imagined without the use of critical raw materials. They require chromium (e.g. in stainless and tool steels), tungsten and cobalt (tool materials, heat resistant alloys), niobium (steels and modern biomaterials). Therefore there is a need to find substitutes to help the European economy. A promising solution can be the application of intermetallics. These materials offer wide variety of interesting properties, such as high hardness and wear resistance or high chemical resistance. In this paper, the overview of possible substitute materials among intermetallics is presented. Intermetallics based on aluminides and silicides are shown as corrosion resistant materials, composites composed of ceramics in intermetallic matrix as possible tool materials. The manufacturing processes are being developed to minimize the disadvantages of these materials, mainly the room-temperature brittleness.

40 CFR 428.75 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

40 CFR 428.75 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

Study on optimum length of raw material in stainless steel high-lock nuts forging

NASA Astrophysics Data System (ADS)

Cheng, Meiwen; Liu, Fenglei; Zhao, Qingyun; Wang, Lidong

2018-04-01

Taking 302 stainless steel (1Cr18Ni9) high-lock nuts for research objects, adjusting the length of raw material, then using DEFORM software to simulate the isothermal forging process of each station and conducting the corresponding field tests to study the effects of raw material size on the stainless steel high-lock nuts forming performance. The tests show that the samples of each raw material length is basically the same as the results of the DEFORM software. When the length of the raw material is 10mm, the appearance size of the parts can meet the design requirements.

[Simultaneous separation and detection of principal component isomer and related substances of raw material drug of ammonium glycyrrhizinate by RP-HPLC and structure confirmation].

PubMed

Zhao, Yan-Yan; Liu, Li-Yan; Han, Yuan-Yuan; Li, Yue-Qiu; Wang, Yan; Shi, Min-Jian

2013-08-01

A simple, fast and sensitive analytical method for the simultaneous separation and detection of 18alpha-glycyrrhizinic acid, 18beta-glycyrrhizinic acid, related substance A and related substance B by RP-HPLC and drug quality standard was established. The structures of principal component isomer and related substances of raw material drug of ammonium glycyrrhizinate have been confirmed. Reference European Pharmacopoeia EP7.0 version, British Pharmacopoeia 2012 version, National Drug Standards of China (WS 1-XG-2002), domestic and international interrelated literature were referred to select the composition of mobile phase. The experimental parameters including salt concentration, pH, addition quantities of organic solvent, column temperature and flow rate were optimized. Finally, the assay was conducted on a Durashell-C18 column (250 mm x 4.6 mm, 5 microm) with 0.01 mol x mL(-1) ammonium perchlorate (add ammonia to adjust the pH value to 8.2) -methanol (48 : 52) as mobile phase at the flow rate of 0.8 mL x min(-1), and the detection wavelength was set at 254 nm. The column temperature was 50 degrees C and the injection volume was 10 microL. The MS, NMR, UV and RP-HPLC were used to confirm the structures of principal component isomer and related substances of raw material drug of ammonium glycyrrhizinate. Under the optimized separation conditions, the calibration curves of 18 alpha-glycyrrhizinic acid, 18beta-glycyrrhizinic acid, related substance A and related substance B showed good linearity within the concentration of 0.50-100 microg x mL(-1) (r = 0.999 9). The detection limits for 18alpha-glycyrrhizinic acid, 18beta-glycyrrhizinic acid, related substance A and related substance B were 0.15, 0.10, 0.10, 0.15 microg x mL(-1) respectively. The method is sensitive, reproducible and the results are accurate and reliable. It can be used for chiral resolution of 18alpha-glycyrrhizinic acid, 18Pbeta-glycyrrhizinic acid, and detection content of principal component and related substances of raw material drug of ammonium glycyrrhizinate. It is concluded that the separation of principal component isomer of raw material drug of ammonium glycyrrhizinate and the validity of the substance's structure assignments of retention time being 1.2 in the European pharmacopoeia EP7.0 version, British pharmacopoeia 2012 version remains open to question. It may be of practical value for the quality control of raw material drug, preparation, and Chinese herbal medicine of ammonium glycyrrhizinate.

A Development Strategy for Creating a Suite of Reference Materials for the in-situ Microanalysis of Non-conventional Raw Materials

NASA Astrophysics Data System (ADS)

Renno, A. D.; Merchel, S.; Michalak, P. P.; Munnik, F.; Wiedenbeck, M.

2010-12-01

Recent economic trends regarding the supply of rare metals readily justify scientific research into non-conventional raw materials, where a particular need is a better understanding of the relationship between mineralogy, microstructure and the distribution of key metals within ore deposits (geometallurgy). Achieving these goals will require an extensive usage of in-situ microanalytical techniques capable of spatially resolving material heterogeneities which can be key for understanding better resource utilization. The availability of certified reference materials (CRMs) is an essential prerequisite for (1) validating new analytical methods, (2) demonstrating data quality to the contracting authorities, (3) supporting method development and instrument calibration, and (4) establishing traceability between new analytical approaches and existing data sets. This need has led to the granting of funding by the European Union and the German Free State of Saxony for a program to develop such reference materials . This effort will apply the following strategies during the selection of the phases: (1) will use exclusively synthetic minerals, thereby providing large volumes of homogeneous starting material. (2) will focus on matrices which are capable of incorporating many ‘important’ elements while avoid exotic compositions which would not be optimal matrix matches. (3) will emphasise those phases which remain stable during the various microanalytical procedure. This initiative will assess the homogeneity of the reference materials at sampling sizes ranging between 50 and 1 µm; it is also intended to document crystal structural homogeneity too, as this too may potentially impact specific analytical methods. As far as possible both definitive methods as well as methods involving matrix corrections will be used for determining the compositions of the of the individual materials. A critical challenge will be the validation of the determination of analytes concentrations as sub-µg sampling masses. It is planned to cooperate with those who are interested in the development of such reference materials and we invite them to take part in round-robin exercises.

40 CFR 428.55 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

40 CFR 428.55 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

40 CFR 428.65 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.0...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

40 CFR 428.65 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.0...— Metric units (kg/kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead...

Synthesis and Performance of Tungsten Disulfide/Carbon (WS2/C) Composite as Anode Material

NASA Astrophysics Data System (ADS)

Yuan, Zhengyong; Jiang, Qiang; Feng, Chuanqi; Chen, Xiao; Guo, Zaiping

2018-01-01

The precursors of an amorphous WS2/C composite were synthesized by a simple hydrothermal method using Na2WO4·2H2O and CH3CSNH2 as raw materials, polyethylene glycol as dispersant, and glucose as the carbon source. The as-synthesized precursors were further annealed at a low temperature in flowing argon to obtain the final materials (WS2/C composite). The structure and morphology of the WS2/C composite were characterized by x-ray diffraction, x-ray photoelectron spectroscopy, and scanning electron microscopy. The electrochemical properties were tested by galvanostatic charge/discharge testing and alternating current (AC) impedance measurements. The results show that the as-prepared amorphous WS2/C composite features both high specific capacity and good cycling performance at room temperature within the potential window from 3.0 V to 0.01 V (versus Li+/Li) at current density of 100 mAg-1. The achieved initial discharge capacity was 1080 mAhg-1, and 786 mAhg-1 was retained after 170 cycles. Furthermore, the amorphous WS2/C composite exhibited a lower charge/discharge plateau than bare WS2, which is more beneficial for use as an anode. The cyclic voltammetry and AC impedance testing further confirmed the change in the plateau and the decrease in the charge transfer resistance in the WS2/C composite. The chemical formation process and the electrochemical mechanism of the WS2/C composite are also presented. The amorphous WS2/C composite can be used as a new anode material for future applications.

Environmental durability of ceramics and ceramic composites

NASA Technical Reports Server (NTRS)

Fox, Dennis S.

1992-01-01

An account is given of the current understanding of the environmental durability of both monolithic ceramics and ceramic-matrix composites, with a view to the prospective development of methods for the characterization, prediction, and improvement of ceramics' environmental durability. Attention is given to the environmental degradation behaviors of SiC, Si3N4, Al2O3, and glass-ceramic matrix compositions. The focus of corrosion prevention in Si-based ceramics such as SiC and Si3N4 is on the high and low sulfur fuel combustion-product effects encountered in heat engine applications of these ceramics; sintering additives and raw material impurities are noted to play a decisive role in ceramics' high temperature environmental response.

[Husk of Venezuelan cocoa as raw material of infusions].

PubMed

Sangronis, Elba; José Soto, María; Valero, Yolmar; Buscema, Ignacio

2014-06-01

In the cocoa bean industry, some by-products go underutilized. Some of these components could provide other innovative products, and such is the case with the husk of the cocoa bean. Previous studies have attributed the husk with a high antioxidant capacity, which added to its relative low cost, makes it an attractive ingredient for the production of infusions. However, prior to promoting it as such, its quality needs to be guaranteed. This study evaluated the chemical composition of the husk of cocoa, its microbiologic quality and other parameters in order to be considered raw material in the preparation of infusions. The cocoa was cultivated in two different states in Venezuela. Moisture, protein, fat, ash, carbohydrates, microbiologic quality and ochratoxin A as well antioxidant properties, content of foreign matter, insoluble ash in HCL and aqueous extract were evaluated in the husk of cocoa seeds. Applied methods were in compliance with national and international norms. Significant differences were determined between the samples through the ANOVA application. A low level in moisture content, but high in ash, along with a microbiologic quality that met the norm, and an absence of ochratoxin A were observed in the totality of the analyzed samples. Low levels of foreign matter, the high value of its aqueous extract and high phenolic compounds content with antioxidant activity allow for the recommendation of the husk of cocoa as raw material for the preparation of infusions.

Application of a quality by design approach to the cell culture process of monoclonal antibody production, resulting in the establishment of a design space.

PubMed

Nagashima, Hiroaki; Watari, Akiko; Shinoda, Yasuharu; Okamoto, Hiroshi; Takuma, Shinya

2013-12-01

This case study describes the application of Quality by Design elements to the process of culturing Chinese hamster ovary cells in the production of a monoclonal antibody. All steps in the cell culture process and all process parameters in each step were identified by using a cause-and-effect diagram. Prospective risk assessment using failure mode and effects analysis identified the following four potential critical process parameters in the production culture step: initial viable cell density, culture duration, pH, and temperature. These parameters and lot-to-lot variability in raw material were then evaluated by process characterization utilizing a design of experiments approach consisting of a face-centered central composite design integrated with a full factorial design. Process characterization was conducted using a scaled down model that had been qualified by comparison with large-scale production data. Multivariate regression analysis was used to establish statistical prediction models for performance indicators and quality attributes; with these, we constructed contour plots and conducted Monte Carlo simulation to clarify the design space. The statistical analyses, especially for raw materials, identified set point values, which were most robust with respect to the lot-to-lot variability of raw materials while keeping the product quality within the acceptance criteria. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

Quantitative analysis of the 26 allergens for cosmetic labeling in fragrance raw materials and perfume oils.

PubMed

Leijs, Hans; Broekhans, Joost; van Pelt, Leon; Mussinan, Cynthia

2005-07-13

The adoption of the 7th amendment of the European Cosmetic Directive 76/768/EEC requires any cosmetic product containing any of 26 raw materials identified by the Scientific Committee on Cosmetic Products and Non-Food Products intended for Consumers as likely to cause a contact allergy when present above certain trigger levels to be declared on the package label. Of these 26, 24 are volatile and can be analyzed by GC. This paper describes a method for the quantitative analysis of these volatile raw materials in perfume ingredients as well as complex perfume compositions. The method uses sequential dual-column GC-MS analysis. The full-scan data acquired minimize the false-positive and false-negative identifications that can be observed with alternate methods based on data acquired in the SIM mode. For each sample, allergen levels are determined on both columns sequentially, leading to two numerical results for each allergen. Quantification limits for each allergen in a perfume mixture based on the analysis of a standard are <4 mg/kg. This is well below the level that would trigger label declaration on the consumer good. Calibration curves for all allergens are linear (r > 0.999) and stable for multiple days. Studies on perfumes spiked with multiple allergens at 30, 50, and 70 mg/kg show recoveries close to nominal values.

INTRAW, the EU Observatory for raw materials: fostering international cooperation and developing new opportunities

NASA Astrophysics Data System (ADS)

Correia, Victor; Allington, Ruth; Keane, Christopher

2016-04-01

A secure supply of raw materials is a European priority that extends beyond country borders and national policies. Recent European initiatives have pioneered the development of an EU strategy on raw materials emphasizing the concept of the "added value chain", which continues to pursue the three pillar strategy to: (1) ensure the fair and sustainable supply of raw materials from international markets, promoting international cooperation with developed and developing countries; (2) foster sustainable supply of raw materials from European sources, and (3) reduce consumption of primary raw materials by increasing resource efficiency and promoting recycling. This contribution presents the Horizon 2020 funded project INTRAW, the objective of which is to establish the European Union's International Observatory for Raw Materials. The creation and maintenance of the European Union's International Observatory for Raw Materials is designed to have a strong impact in two dimensions: 1. To narrow the existing gap in aspects of the raw materials knowledge infrastructure in the EU by providing a link with the same knowledge infrastructure in technologically advanced reference countries. This should contribute to the harmonization of mineral policies all over the EU, by providing data that enables evidence-based policies and appropriate, cost-effective management, planning and adaptation decisions by the public sector. This will benefit businesses, industry and society. The Observatory will also provide to policy makers in the EU and its Member States the data they need to facilitate discussion in multilateral forums. 2. To enable a better alignment of the R&I activities among the individual EU members and international cooperation countries AND between the European Union and international cooperation countries by boosting synergies with international research and innovation programmes. This way the EU's role and scientific capabilities in the raw materials area will be reinforced in the mid-term, and the conditions for sustainable access and supply of raw materials in the EU will benefit from the international cooperation. The authors will describe the key stages of the INTRAW project and explain how it aims to establish (and promote the continuation of) international cooperation at every stage of the raw materials value chain and to build a repository of information and analysis to support the development and strengthening of EU raw materials strategies. Key elements of the value chain upon which the project focuses are: industry and trade; education and outreach; and research and innovation. The roles of geoscientists in delivering the aims and objectives of INTRAW will be emphasised.

Methodology for Evaluating Raw Material Changes to RSRM Elastomeric Insulation Materials

NASA Technical Reports Server (NTRS)

Mildenhall, Scott D.; McCool, Alex (Technical Monitor)

2001-01-01

The Reusable Solid Rocket Motor (RSRM) uses asbestos and silicon dioxide filled acrylonitrile butadiene rubber (AS-NBR) as the primary internal insulation to protect the case from heat. During the course of the RSRM Program, several changes have been made to the raw materials and processing of the AS-NBR elastomeric insulation material. These changes have been primarily caused by raw materials becoming obsolete. In addition, some process changes have been implemented that were deemed necessary to improve the quality and consistency of the AS-NBR insulation material. Each change has been evaluated using unique test efforts customized to determine the potential impacts of the specific raw material or process change. Following the evaluations, the various raw material and process changes were successfully implemented with no detectable effect on the performance of the AS-NBR insulation. This paper will discuss some of the raw material and process changes evaluated, the methodology used in designing the unique test plans, and the general evaluation results. A summary of the change history of RSRM AS-NBR internal insulation is also presented.

Process to create simulated lunar agglutinate particles

NASA Technical Reports Server (NTRS)

Gustafson, Robert J. (Inventor); Gustafson, Marty A. (Inventor); White, Brant C. (Inventor)

2011-01-01

A method of creating simulated agglutinate particles by applying a heat source sufficient to partially melt a raw material is provided. The raw material is preferably any lunar soil simulant, crushed mineral, mixture of crushed minerals, or similar material, and the heat source creates localized heating of the raw material.

Fabrication of Powder Metallurgy Pure Ti Material by Using Thermal Decomposition of TiH2

NASA Astrophysics Data System (ADS)

Mimoto, Takanori; Nakanishi, Nozomi; Umeda, Junko; Kondoh, Katsuyoshi

Titanium (Ti) and titanium alloys have been interested as an engineering material because they are widely used across various industrial applications, for example, motorcycle, automotive and aerospace industries, due to their light weight, high specific strength and superior corrosion resistance. Ti materials are particularly significant for the aircraft using carbon/carbon (C/C) composites, for example, carbon fiber reinforced plastics (CFRP), because Ti materials are free from the problem of contact corrosion between C/C composites. However, the applications of Ti materials are limited because of their high cost. From a viewpoint of cost reduction, cost effective process to fabricate Ti materials is strongly required. In the present study, the direct consolidation of titanium hydride (TiH2) raw powders in solid-state was employed to fabricate pure Ti bulk materials by using thermal decomposition of TiH2. In general, the production cost of Ti components is expensive due to using commercially pure (CP) Ti powders after dehydrogenation. On the other hand, the novel process using TiH2 powders as starting materials is a promising low cost approach for powder metallurgy (P/M) Ti products. Furthermore, this new process is also attractive from a viewpoint of energy saving because the dehydrogenation is integrated into the sintering process. In this study, TiH2 raw powders were directly consolidated by conventional press technique at 600 MPa to prepare TiH2 powder compacted billets. To thermally decompose TiH2 and obtain sintered pure Ti billets, the TiH2 powder billets were heated in the integrated sintering process including dehydrogenation. The hot-extruded pure Ti material, which was heat treated at 1273 K for 180 min in argon gas atmosphere, showed tensile strength of 701.8 MPa and elongation of 27.1%. These tensile properties satisfied the requirements for JIS Ti Grade 4. The relationship between microstructures, mechanical properties response and heat treatment temperature is discussed in detail.

40 CFR 428.72 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0.../kkg of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead 0.0017 0.0007...

40 CFR 428.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25... of raw material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead 0.0017 0.0007 (c...

Phenolics in Primula veris L. and P. elatior (L.) Hill Raw Materials

PubMed Central

Mirgos, Małgorzata; Kosakowska, Olga; Szymborska-Sandhu, Izabela; Węglarz, Zenon

2017-01-01

Primula veris L. and Primula elatior (L.) Hill represent medicinal plants used for the production of herbal teas and preparations with antioxidant and expectorant activity. Flowers and roots of both species possess the same biological activity. In the presented study, raw materials of wild growing P. veris and P. elatior were compared in terms of the content and composition of phenolic compounds using a fast and simple HPLC-DAD method. The study showed that flowers of both species were rich in flavonoids. However, P. veris flowers were characterized with a distinctly higher content of isorhamnetin-3-O-glucoside, astragalin, and (+)-catechin, whereas P. elatior occurred to be a richer source of rutoside and isorhamnetin-3-O-rutinoside. Hyperoside was found exclusively in P. elatior flowers. Phenolic glycosides (primverin and primulaverin) were identified only in the roots. Their content was about ten times higher in P. veris in comparison with P. elatior underground organs. The obtained results clearly show that both Primula species differ distinctly in terms of the content and composition of phenolic compounds. The compounds differentiating both species to the highest degree (hyperoside, in flowers, as well as primverin and primulaverin, in the roots) may be useful chemical markers in the identification and evaluation of both species. PMID:28835753

Composition and biological activities of hydrolyzable tannins of fruits of Phyllanthus emblica.

PubMed

Yang, Baoru; Liu, Pengzhan

2014-01-22

Fruits of emblic leafflower have been used as food and traditional medicine in Asia. A wide range of biological activities have been shown in modern research suggesting potential of the fruits as healthy food and raw material for bioactive ingredients of food. Hydrolyzable tannins are among the major bioactive components of the fruits. Mucic acid gallate, mucic acid lactone gallate, monogalloylglucose, gallic acid, digalloylglucose, putranjivain A, galloyl-HHDP-glucose, elaeocarpusin, and chebulagic acid are the most abundant hydrolyzable tannins. The compositional profiles of tannins in the fruits vary depending on the cultivars as well as ripening stages. Fruits and tannin-rich extracts of fruits have shown antidiabetic, antimicrobial, anti-inflammatory, and immune-regulating activities in vitro and in animal studies. The fruits and fruit extracts have manifested protective effects on organs/tissues from damages induced by chemicals, stresses, and aging in animal models. The fruits and fruit extracts have potential in inhibiting the growth of cancer cells and reducing DNA damage induced by chemicals and radiation. Antioxidative activities are likely among the mechanisms of the biological activities and physiological effects. Human intervention/clinical studies are needed to investigate the bioavailability and metabolism of the tannins and to substantiate the health benefits in humans. Emblic leafflower may be a potential raw material for natural food preservatives.

The effect of raw materials on thermo-oxidative stability and glycidyl ester content of palm oil during frying.

PubMed

Aniołowska, Magda A; Kita, Agnieszka M

2016-04-01

The objective of this research was to determine the effects of the water content of food incorporated into frying oil on oil degradation and the content of glycidyl esters. Potato chips, French fries and snacks were fried intermittently in palm oil, which was heated at 180 °C for 8 h per day over five consecutive days. Thermo-oxidative and physical alterations, changes in fatty acid composition, total polar components, polar fraction composition, and water content were analysed. The content of glycidyl esters was measured by liquid chromatography-tandem mass spectrometry. More polar compounds were formed in the oil used for frying chips (252 g kg(-1)) than for French fries (229 g kg(-1)) or snacks (196 g kg(-1)). Reductions in glycidyl esters were found in oils used for frying--greater for frying snacks and French fries (95% and 93%) than for potato chips (87%). The rate of decrease of glycidyl esters was correlated with frying parameters, most strongly with the concentrations of diacylglycerols (r = 0.98) and total polar components (r = -0.98). The raw material had a greater influence on polymerization conversion and glycidyl ester content than on hydrolytic and oxidative changes in the frying oil. © 2015 Society of Chemical Industry.

VERAM - Vision and Roadmap for European Raw Materials

NASA Astrophysics Data System (ADS)

Baumgarten, Wibke; Vashev, Boris

2017-04-01

The overall objective of VERAM project is to produce a Vision and Roadmap for European Raw Materials in 2050 based on raw materials research and innovation (R&I) coordination. Two leading European Technology Platforms (ETPs): ETP SMR (Sustainable Minerals Resources) and FTP (Forest Technology Platform) are joining forces to develop a common vison and roadmap with the support of ECTP (European Construction Technology Platform), represented by UNIVPM, SusChem (ETP for Sustainable Chemistry), represented by Cefic, EuMaT (Advanced Materials ETP), represented by VITO, ERAMIN 2, represented by Research Centre JUELICH and WoodWisdom Network Plus represented by the Agency for Renewable Resources (FNR). This partnership provides VERAM with expertise from downstream applications and additional knowledge on non-biotic and biotic raw materials. The project encourages capacity building as well as transfer of knowledge. It expects to provide an innovation reference point for the European Institute of Innovation & Technology (EIT) Raw Materials (formerly the KIC Raw MatTERS), to coordinate the network involved in the European Innovation Partnership (EIP) on Raw Materials Commitments and relevant proposals funded under Horizon 2020. It provides a platform for identifying gaps and complementarities and enables their bridging. VERAM will be able to advise the European Commission and Member States on future research needs and policies to stimulate innovation and assist in overcoming fragmentation in the implementing the EIP Raw Materials Strategic Implementation Plan. VERAM looks for mutually beneficial information exchange, encourages cross-fertilization between actions undertaken by different raw material industries, and expects to accelerate exploitation of breakthrough innovations. One of the main outcomes of the project is the presentation of a common long term 2050 Vision and Roadmap for relevant raw materials including metals, industrial minerals and aggregates and wood. The Vision and Roadmap have the objective of highlighting the path to achieving the European Commission's ambitious target of 80% reduction in CO2 emissions by 2050.

Effective utilizations of palm oil mill fly ash for synthetic amorphous silica and carbon zeolite composite synthesis

NASA Astrophysics Data System (ADS)

Utama, P. S.; Saputra, E.; Khairat

2018-04-01

Palm Oil Mill Fly Ash (POMFA) the solid waste of palm oil industry was used as a raw material for synthetic amorphous silica and carbon zeolite composite synthesis in order to minimize the wastes of palm oil industry. The alkaline extraction combine with the sol-gel precipitation and mechanical fragmentation was applied to produce synthetic amorphous silica. The byproduct, extracted POMFA was rich in carbon and silica content in a significant amount. The microwave heated hydrothermal process used to synthesize carbon zeolite composite from the byproduct. The obtained silica had chemical composition, specific surface area and the micrograph similar to commercial precipitated silica for rubber filler. The microwave heated hydrothermal process has a great potential for synthesizing carbon zeolite composite. The process only needs one-step and shorter time compare to conventional hydrothermal process.

Influence of input material and operational performance on the physical and chemical properties of MSW compost.

PubMed

Montejo, C; Costa, C; Márquez, M C

2015-10-01

Certain controversy exists about the use of compost from MSW (municipal solid waste) and, specifically, from the organic fraction of MSW that has not been separated at the source. In this case, the final composition of MSW compost is related to the performance of the separation process in MBT (Mechanical and Biological Treatment) plants as well as the composition of raw materials and the particular features of composting systems. In an effort to investigate the quality of MSW compost, 30 samples of this product obtained from 10 different MBT plants were studied. The main physical and chemical properties were analyzed and were compared with the requirements of current legislation. The composting systems used to produce these compost samples were studied and the input materials were characterized. The results reveal that the heavy metal content in MSW compost was below the legal restrictions in all samples but one; however, in most of them the percentage of Pb was high. The fertilizing potential of MSW compost has been demonstrated by its high nutrient concentrations, particularly N, K, P, Ca and Mg. Nevertheless, here the percentage of inert impurities with a size larger than 2 mm, such as plastic or glass, was seen to be excessively high exceeding in some cases the legal limit. The source of such pollution lies in the composting inputs, OFMSW (organic fraction of MSW), which showed high percentages of improper materials such as plastic (9%) or glass (11%). Accordingly, the performance of the sorting stage for the collection of the raw material must be improved, as must the refining process, since this does not remove the necessary amounts of these impurities from the final compost. Copyright © 2015 Elsevier Ltd. All rights reserved.

Systematic approach to preparing ceramic-glass composites with high translucency for dental restorations.

PubMed

Yoshimura, Humberto N; Chimanski, Afonso; Cesar, Paulo F

2015-10-01

Ceramic composites are promising materials for dental restorations. However, it is difficult to prepare highly translucent composites due to the light scattering that occurs in multiphase ceramics. The objective of this work was to verify the effectiveness of a systematic approach in designing specific glass compositions with target properties in order to prepare glass infiltrated ceramic composites with high translucency. First it was necessary to calculate from literature data the viscosity of glass at the infiltration temperature using the SciGlass software. Then, a glass composition was designed for targeted viscosity and refractive index. The glass of the system SiO2-B2O3-Al2O3-La2O3-TiO2 prepared by melting the oxide raw materials was spontaneously infiltrated into porous alumina preforms at 1200°C. The optical properties were evaluated using a refractometer and a spectrophotometer. The absorption and scattering coefficients were calculated using the Kubelka-Munk model. The light transmittance of prepared composite was significantly higher than a commercial ceramic-glass composite, due to the matching of glass and preform refractive indexes which decreased the scattering, and also to the decrease in absorption coefficient. The proposed systematic approach was efficient for development of glass infiltrated ceramic composites with high translucency, which benefits include the better aesthetic performance of the final prosthesis. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

40 CFR 428.103 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6... raw material) Chromium 0.0086 0.0036 English units (lb/1,000 lb of raw material) Chromium 0.0086 0...

40 CFR 428.103 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6... raw material) Chromium 0.0086 0.0036 English units (lb/1,000 lb of raw material) Chromium 0.0086 0...

40 CFR 428.102 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5... units (kg/kkg of raw material) Chromium 0.0086 0.0036 English units (lb/1,000 lb of raw material...

Chemical composition of individual aerosol particles in workplace air during production of manganese alloys.

PubMed

Gunst, S; Weinbruch, S; Wentzel, M; Ortner, H M; Skogstad, A; Hetland, S; Thomassen, Y

2000-02-01

Aerosol particle samples were collected at ELKEM ASA ferromanganese (FeMn) and silicomanganese (SiMn) smelters at Porsgrunn, Norway, during different production steps: raw material mixing, welding of protective steel casings, tapping of FeMn and slag, crane operation moving the ladles with molten metal, operation of the Metal Oxygen Refinement (MOR) reactor and casting of SiMn. Aerosol fractions were assessed for the analysis of the bulk elemental composition as well as for individual particle analysis. The bulk elemental composition was determined by inductively coupled plasma atomic emission spectrometry. For individual particle analysis, an electron microprobe was used in combination with wavelength-dispersive techniques. Most particles show a complex composition and cannot be attributed to a single phase. Therefore, the particles were divided into six groups according to their chemical composition: Group I, particles containing mainly metallic Fe and/or Mn; Group II, slag particles containing mainly Fe and/or Mn oxides; Group III, slag particles consisting predominantly of oxidized flux components such as Si, Al, Mg, Ca, Na and K; Group IV, particles consisting mainly of carbon; Group V, mixtures of particles from Groups II, III and IV; Group VI, mixtures of particles from Groups II and III. In raw material mixing, particles originating from the Mn ores were mostly found. In the welding of steel casings, most particles were assigned to Group II, Mn and Fe oxides. During the tapping of slag and metal, mostly slag particles from Group III were found (oxides of the flux components). During movement of the ladles, most particles came from Group II. At the MOR reactor, most of the particles belonged to the slag phase consisting of the flux components (Group III). The particles collected during the casting of SiMn were mainly attributed to the slag phase (Groups III and V). Due to the compositional complexity of the particles, toxicological investigations on the kinetics of pure compounds may not be easily associated with the results of this study.

Characterization of pore and crystal structure of synthesized LiBOB with varying quality of raw materials as electrolyte for lithium-ion battery

NASA Astrophysics Data System (ADS)

Lestariningsih, Titik; Ratri, Christin Rina; Wigayati, Etty Marty; Sabrina, Qolby

2016-02-01

Characterization of pore structure and crystal structure of the LiB(C2O4)2H2O or LIBOB compound has been performed in this study. These recent years, research regarding LiBOB electrolyte salt have been performed using analytical-grade raw materials, therefore this research was aimed to synthesized LiBOB electrolyte salt using the cheaper and abundant technical-grade raw materials. Lithium hydroxide (LiOH), oxalic acid dihydrate (H2C2O4.2H2O), and boric acid (H3BO3) both in technical-grade and analytical-grade quality were used as raw materials for the synthesis of LiBOB. Crystal structure characterization results of synthesized LiBOB from both technical-grade and analytical-grade raw materials have shown the existence of LiBOB and LiBOB hydrate phase with orthorombic structure. These results were also confirmed by FT-IR analysis, which showed the functional groups of LiBOB compounds. SEM analysis results showed that synthesized LiBOB has spherical structure, while commercial LiBOB has cylindrical structure. Synthesized LiBOB has a similar pore size of commercial LiBOB, i.e. 19 nm (mesoporous material). Surface area of synthesized LiBOB from analytical-grade raw materials and technical-grade materials as well as commercial LIBOB were 88.556 m2/g, 41.524 m2/g, and 108.776 m2/g, respectively. EIS analysis results showed that synthesized LiBOB from technical-grade raw materials has lower conductivity than synthesized LiBOB from analytical-grade raw materials.

Improved C/SiC Ceramic Composites Made Using PIP

NASA Technical Reports Server (NTRS)

Easler, Timothy

2007-01-01

Improved carbon-fiber-reinforced SiC ceramic-matrix composite (C/SiC CMC) materials, suitable for fabrication of thick-section structural components, are producible by use of a combination of raw materials and processing conditions different from such combinations used in the prior art. In comparison with prior C/SiC CMC materials, these materials have more nearly uniform density, less porosity, and greater strength. The majority of raw-material/processing-condition combinations used in the prior art involve the use of chemical vapor infiltration (CVI) for densifying the matrix. In contrast, in synthesizing a material of the present type, one uses a combination of infiltration with, and pyrolysis of, a preceramic polymer [polymer infiltration followed by pyrolysis (PIP)]. PIP processing is performed in repeated, tailored cycles of infiltration followed by pyrolysis. Densification by PIP processing takes less time and costs less than does densification by CVI. When one of these improved materials was tested by exposure to a high-temperature, inert-gas environment that caused prior C/SiC CMCs to lose strength, this material did not lose strength. (Information on the temperature and exposure time was not available at the time of writing this article.) A material of the present improved type consists, more specifically, of (1) carbon fibers coated with an engineered fiber/matrix interface material and (2) a ceramic matrix, containing SiC, derived from a pre-ceramic polymer with ceramic powder additions. The enhancements of properties of these materials relative to those of prior C/SiC CMC materials are attributable largely to engineering of the fiber/ matrix interfacial material and the densification process. The synthesis of a material of this type includes processing at an elevated temperature to a low level of open porosity. The approach followed in this processing allows one to fabricate not only simple plates but also more complexly shaped parts. The carbon fiber reinforcement in a material of this type can be in any of several alternative forms, including tow, fabric, or complex preforms containing fibers oriented in multiple directions.

Investigation of Air-Liquid Interface Rings in Buffer Preparation Vessels: the Role of Slip Agents.

PubMed

Shi, Ting; Ding, Wei; Kessler, Donald W; De Mas, Nuria; Weaver, Douglas G; Pathirana, Charles; Martin, Russell D; Mackin, Nancy A; Casati, Michael; Miller, Scott A; Pla, Itzcoatl A

2016-01-01

Air-liquid interface rings were observed on the side walls of stainless steel buffer vessels after certain downstream buffer preparations. Those rings were resistant to regular cleaning-in-place procedures but could be removed by manual means. To investigate the root cause of this issue, multiple analytical techniques, including liquid chromatography with tandem mass spectrometry detection (LC-MS/MS), high-resolution accurate mass liquid chromatography with mass spectrometry, nuclear magnetic resonance, Fourier transform infrared spectroscopy, and scanning electron microscopy with energy-dispersive X-ray spectroscopy have been employed to characterize the chemical composition of air-liquid interface rings. The main component of air-liquid interface rings was determined to be slip agents, and the origin of the slip agents can be traced back to their presence on raw material packaging liners. Slip agents are commonly used in plastic industry as additives to reduce the coefficient of friction during the manufacturing process of thin films. To mitigate this air-liquid interface ring issue, an alternate liner with low slip agent was identified and implemented with minimal additional cost. We have also proactively tested the packaging liners of other raw materials currently used in our downstream buffer preparation to ensure slip agent levels are appropriate. Air-liquid interface rings were observed on the side walls of stainless steel buffer vessels after certain downstream buffer preparations. To investigate the root cause of this issue, multiple analytical techniques have been employed to characterize the chemical composition of air-liquid interface rings. The main components of air-liquid interface rings were determined to be slip agents, which are common additives used in the manufacturing process of thin films. The origin of the slip agents can be traced back to their presence on certain raw material packaging liners. To mitigate this air-liquid interface ring issue, an alternate liner with low slip agent was identified and implemented. © PDA, Inc. 2016.

Bioactive β-carbolines norharman and harman in traditional and novel raw materials for chicory coffee.

PubMed

Wojtowicz, Elżbieta; Zawirska-Wojtasiak, Renata; Przygoński, Krzysztof; Mildner-Szkudlarz, Sylwia

2015-05-15

The β-carboline compounds norharman and harman exhibit neuroactive activity in the human body. Chicory coffee has proved to be a source of β-carboline compounds. This study assessed the norharman and harman contents of traditional and novel raw materials for the production of chicory coffee, as well as in samples of chicory coffee with novel additives. The highest content of the β-carbolines among the traditional raw materials was recorded in roasted sugar beet (2.26 μg/g), while roasting the chicory caused a 25-fold increase in the content of norharman in this raw material (from 0.05 to 1.25 μg/g). In novel raw materials not subjected to the action of high temperature, β-carboline was not detected. Among the roasted novel raw materials, the highest contents of harman and norharman were found in artichokes. High harman levels were also recorded in roasted chokeberry. Copyright © 2014 Elsevier Ltd. All rights reserved.

Synthesis of geopolymer from biomass-coal ash blends

NASA Astrophysics Data System (ADS)

Samadhi, Tjokorde Walmiki; Wulandari, Winny; Prasetyo, Muhammad Iqbal; Fernando, Muhammad Rizki; Purbasari, Aprilina

2017-09-01

Geopolymer is an environmentally attractive Portland cement substitute, owing to its lower carbon footprint and its ability to consume various aluminosilicate waste materials as its precursors. This work describes the development of geopolymer formulation based on biomass-coal ash blends, which is predicted to be the prevalent type of waste when biomass-based thermal energy production becomes mainstream in Indonesia. The ash blends contain an ASTM Class F coal fly ash (FA), rice husk ash (RHA), and coconut shell ash (CSA). A mixture of Na2SiO3 and concentrated KOH is used as the activator solution. A preliminary experiment identified the appropriate activator/ash mass ratio to be 2.0, while the activator Na2SiO3/KOH ratio varies from 0.8 to 2.0 with increasing ash blend Si/Al ratio. Both non-blended FA and CSA are able to produce geopolymer mortars with 7-day compressive strength exceeding the Indonesian national SNI 15-2049-2004 standard minimum value of 2.0 MPa stipulated for Portland cement mortars. Ash blends have to be formulated with a maximum RHA content of approximately 50 %-mass to yield satisfactory 7-day strength. No optimum ash blend composition is identified within the simplex ternary ash blend compositional region. The strength decreases with Si/Al ratio of the ash blends due to increasing amount of unreacted silicate raw materials at the end of the geopolymer hardening period. Overall, it is confirmed that CSA and blended RHA are feasible raw materials for geopolymer production..

Use of in vitro methods to rank surfactants for irritation potential in support of new product development.

PubMed

Casterton, P L; Potts, L F; Klein, B D

1994-08-01

11 surfactant raw materials with potential applications in light-duty liquid cleaning products were evaluated in vitro using a human skin analogue (ATS SKIN(2) Model ZK1100) for predicting cytotoxicity (MTT reduction) and inflammation [prostaglandin E(2) (PGE(2)) release]. Two of the 11 raw materials, both in the same compound family, were selected to be individually combined with each of the other nine in a 90:10 (raw:selected raw) mixture. Selection criteria were based on desired performance characteristics and low irritation potential as suggested from the individual surfactant assay data. To determine whether irritation potential was mitigated, MTT and PGE(2) scores were again determined for each of the 18 combinations with the resulting data being compared with the untreated raw material data. A plot of the data indicated that one of two selected materials may have an 'anti-irritant' effect. For raw materials with intrinsic MTT scores of less than 50 mug/ml and with the original data corrected for possible dilution effects, a statistical comparison between individual raw materials and the two sets of combinations was done using a one-sample analysis. Both cytotoxicity (MTT) and inflammation (PGE(2)) were significantly decreased by the milder of the two selected raw materials. By factoring the data into future new product decisions, this methodology has become a useful and practical tool for Amway product development.

Synopsis of utilization research on SRIC raw materials

Treesearch

John B. Crist

1983-01-01

The take-home message of this paper is this: Raw materials produced using SRIC are suitable for many reconstituted end products. Juvenility, rapid growth, and bark contents do not greatly hinder the usefulness of the raw materials. In the future, increased industrial acceptance of SRIC methods and materials should be a major thrust and is discussed.

Microspherical polyaniline/graphene nanocomposites for high performance supercapacitors

NASA Astrophysics Data System (ADS)

Cao, Hailiang; Zhou, Xufeng; Zhang, Yiming; Chen, Liang; Liu, Zhaoping

2013-12-01

Polyaniline/graphene nanocomposites with microspherical morphology and porous structure are prepared as electrode materials for supercapacitors. Using few-layer graphene obtained by liquid phase exfoliation of graphite as the raw material, porous graphene microspheres are produced by spray drying, and are then employed as the substrates for the growth of polyaniline nanowire arrays by in situ polymerization. In the composite, interconnected graphene sheets with few structural defects constitute a high-efficient conductive network to improve the electrical conductivity of polyaniline. Furthermore, the microspherical architecture prevents restacking of polyaniline/graphene composite nanosheets, thus facilitates fast diffusion of electrolytes. Consequently, the nanocomposite exhibits excellent electrochemical performance. A specific capacitance of 338 F g-1 is reached in 1 M H2SO4 at a scan rate of 20 mV s-1, and a high capacity retention rate of 87.4% after 10,000 cycles at a current density of 3 A g-1 can be achieved, which suggests that the polyaniline/graphene composite with such kind of 3D architecture is a promising electrode material for high-performance supercapacitors.

Influence of various amount of diatomaceous earth used as cement substitute on mechanical properties of cement paste

NASA Astrophysics Data System (ADS)

Pokorný, Jaroslav; Pavlíková, Milena; Medved, Igor; Pavlík, Zbyšek; Zahálková, Jana; Rovnaníková, Pavla; Černý, Robert

2016-06-01

Active silica containing materials in the sub-micrometer size range are commonly used for modification of strength parameters and durability of cement based composites. In addition, these materials also assist to accelerate cement hydration. In this paper, two types of diatomaceous earths are used as partial cement replacement in composition of cement paste mixtures. For raw binders, basic physical and chemical properties are studied. The chemical composition of tested materials is determined using classical chemical analysis combined with XRD method that allowed assessment of SiO2 amorphous phase content. For all tested mixtures, initial and final setting times are measured. Basic physical and mechanical properties are measured on hardened paste samples cured 28 days in water. Here, bulk density, matrix density, total open porosity, compressive and flexural strength, are measured. Relationship between compressive strength and total open porosity is studied using several empirical models. The obtained results give evidence of high pozzolanic activity of tested diatomite earths. Their application leads to the increase of both initial and final setting times, decrease of compressive strength, and increase of flexural strength.

Management and characteristics of recycled manure solids used for bedding in Midwest freestall dairy herds.

PubMed

Husfeldt, A W; Endres, M I; Salfer, J A; Janni, K A

2012-04-01

Interest in using recycled manure solids (RMS) as a bedding material for dairy cows has grown in the US Midwest. Cost of common bedding materials has increased in recent years and availability has decreased. Information regarding the composition of RMS and its use as a bedding material for dairy cows in the Midwest is very limited. The objectives of this study were to characterize RMS as a bedding material, observe bedding management practices, document methods of obtaining RMS, and describe housing facilities. We visited 38 Midwest dairy operations bedding freestalls with RMS to collect data. Methods of obtaining RMS for bedding included separation of anaerobic digested manure, separation of raw manure, and separation of raw manure followed by mechanical drum-composting for 18 to 24 h. Average bedding moisture of unused RMS was 72.4% with a pH of 9.16. Unused samples contained (on a dry basis) 1.4% N, 44.9% C, 32.7C:N ratio, 0.44% P, 0.70% K, 76.5% neutral detergent fiber, 9.4% ash, 4.4% nonfiber carbohydrates, and 1.1% fat. Moisture was lowest for drum-composted solids before and after use as freestall bedding. After use in the stalls, digested solids had lower neutral detergent fiber content (70.5%) than drum-composted (75.0%) and separated raw (73.1%) solids. Total N content was greater in digested solids (2.0%) than in separated raw (1.7%) solids. Total bacterial populations in unused bedding were greatest in separated raw manure solids but were similar between digested and drum-composted manure solids. Drum-composted manure solids had no coliform bacteria before use as freestall bedding. After use as bedding, digested manure solids had lower total bacteria counts compared with drum-composted and separated raw manure solids, which had similar counts. Used bedding samples of digested solids contained fewer environmental streptococci than drum-composted and separated raw solids and had reduced Bacillus counts compared with separated raw solids. Coliform counts were similar for all 3 bedding sources. Addition of a mechanical blower post-separation and use of a shelter for storage were associated with reduced fresh-bedding moisture but not associated with bacterial counts. This was the first survey of herds using RMS for bedding in the Midwest. We learned that RMS was being used successfully as a source of bedding for dairy cows. For most farms in the study, somatic cell count was comparable to the average in the region and not excessively high. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Life Cycle Assessment of Completely Recyclable Concrete.

PubMed

De Schepper, Mieke; Van den Heede, Philip; Van Driessche, Isabel; De Belie, Nele

2014-08-21

Since the construction sector uses 50% of the Earth's raw materials and produces 50% of its waste, the development of more durable and sustainable building materials is crucial. Today, Construction and Demolition Waste (CDW) is mainly used in low level applications, namely as unbound material for foundations, e.g., in road construction. Mineral demolition waste can be recycled as crushed aggregates for concrete, but these reduce the compressive strength and affect the workability due to higher values of water absorption. To advance the use of concrete rubble, Completely Recyclable Concrete (CRC) is designed for reincarnation within the cement production, following the Cradle-to-Cradle (C2C) principle. By the design, CRC becomes a resource for cement production because the chemical composition of CRC will be similar to that of cement raw materials. If CRC is used on a regular basis, a closed concrete-cement-concrete material cycle will arise, which is completely different from the current life cycle of traditional concrete. Within the research towards this CRC it is important to quantify the benefit for the environment and Life Cycle Assessment (LCA) needs to be performed, of which the results are presented in a this paper. It was observed that CRC could significantly reduce the global warming potential of concrete.

Life Cycle Assessment of Completely Recyclable Concrete

PubMed Central

De Schepper, Mieke; Van den Heede, Philip; Van Driessche, Isabel; De Belie, Nele

2014-01-01

Since the construction sector uses 50% of the Earth’s raw materials and produces 50% of its waste, the development of more durable and sustainable building materials is crucial. Today, Construction and Demolition Waste (CDW) is mainly used in low level applications, namely as unbound material for foundations, e.g., in road construction. Mineral demolition waste can be recycled as crushed aggregates for concrete, but these reduce the compressive strength and affect the workability due to higher values of water absorption. To advance the use of concrete rubble, Completely Recyclable Concrete (CRC) is designed for reincarnation within the cement production, following the Cradle-to-Cradle (C2C) principle. By the design, CRC becomes a resource for cement production because the chemical composition of CRC will be similar to that of cement raw materials. If CRC is used on a regular basis, a closed concrete-cement-concrete material cycle will arise, which is completely different from the current life cycle of traditional concrete. Within the research towards this CRC it is important to quantify the benefit for the environment and Life Cycle Assessment (LCA) needs to be performed, of which the results are presented in a this paper. It was observed that CRC could significantly reduce the global warming potential of concrete. PMID:28788174

7 CFR 58.735 - Quality specifications for raw materials.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality specifications for raw materials. 58.735 Section 58.735 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... specifications for raw materials. (a) Cheddar colby, washed or soaked curd, granular or stirred curd cheese...

Future Sources of Organic Raw Materials.

ERIC Educational Resources Information Center

Shapiro, Irving S.

1978-01-01

Examines the need for industrial organization, academic institutions, and national governments to agree on cooperative roles in planning the future raw materials demands of the chemical industry. Political and social concerns, as well as technical and economic considerations, are important to the raw material future of the industry. (MA)

Changes in microbial composition and the prevalence of foodborne pathogens in crab marinated in soy sauce produced by six manufacturing plants.

PubMed

Kim, Sun Ae; Choi, Eun Sook; Kim, Nam Hee; Kim, Hye Won; Lee, Na Young; Cho, Tae Jin; Jo, Jun Il; Kim, Soon Han; Lee, Soon Ho; Ha, Sang Do; Rhee, Min Suk

2017-04-01

The present study examined the changes in microbiological composition during the production process of crab marinated in soy sauce, potential microbial hazards, potential contamination routes and effective critical control points. Crab and soy sauce samples were obtained from six different manufacturing plants at different stages, and their microbiological content was comprehensively assessed by quantitative and qualitative analyses. The results revealed the following: (1) the final products contained 4.0 log colony-forming units (CFU) g -1 aerobic plate counts (APCs) and 1.1 log CFU g -1 coliforms, which may have been introduced from the raw materials (the level of APCs in raw crab and soy sauce mixed with other ingredients was 3.8 log CFU g -1 and 4.0 log CFU mL -1 respectively); (2) marination of crab in soy sauce may allow cross-contamination by coliforms; (3) only Bacillus cereus and Staphylococcus aureus were qualitatively detected in samples at different stages of manufacture (detection rate of 28 and 5.6% respectively), and these bacteria may impact the microbiological quality and safety of crab marinated in soy sauce; and (4) bacterial counts were either maintained or increased during the manufacturing process (suggesting that no particular step can be targeted to reduce bacterial counts). Proper management of raw materials and the marination process are effective critical control points, and alternative interventions may be needed to control bacterial quantity. The results provide important basic information about the production of crab marinated in soy sauce and may facilitate effective implementation of sanitary management practices in related industries and research fields. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Chemical recycling of plastic wastes made from polyethylene (LDPE and HDPE) and polypropylene (PP).

PubMed

Achilias, D S; Roupakias, C; Megalokonomos, P; Lappas, A A; Antonakou, Epsilon V

2007-11-19

The recycling of either model polymers or waste products based on low-density polyethylene (LDPE), high-density polyethylene (HDPE) or polypropylene (PP) is examined using the dissolution/reprecipitation method, as well as pyrolysis. In the first technique, different solvents/non-solvents were examined at different weight percent amounts and temperatures using as raw material both model polymers and commercial products (packaging film, bags, pipes, food-retail outlets). The recovery of polymer in every case was greater than 90%. FT-IR spectra and tensile mechanical properties of the samples before and after recycling were measured. Furthermore, catalytic pyrolysis was carried out in a laboratory fixed bed reactor with an FCC catalyst using again model polymers and waste products as raw materials. Analysis of the derived gases and oils showed that pyrolysis gave a mainly aliphatic composition consisting of a series of hydrocarbons (alkanes and alkenes), with a great potential to be recycled back into the petrochemical industry as a feedstock for the production of new plastics or refined fuels.

Optimized extraction of polysaccharides from Cymbopogon citratus and its biological activities.

PubMed

Thangam, Ramar; Suresh, Veeraperumal; Kannan, Soundarapandian

2014-04-01

In this study the extraction of hot water soluble polysaccharides (HWSPs) from Cymbopogon citratus using hot water decoction was discussed. Response surface methodology (RSM) based on a three level, three variable central composite rotatable design (CCRD), was employed to obtain best possible combination of extraction time (X1: 30-180 min), extraction temperature (X2: 70-100 °C) and water to the raw material ratio (X3: 10-60) for maximum HWSPs extraction. The optimum extraction conditions were as follows: extraction time was around 113.81 min, extraction temperature at 99.66 °C and the ratio of water to raw material was 33.11 g/mL. Under these conditions, the experimental yield was 13.24±0.23%, which is well in close agreement with the value predicted by RSM model yield (13.19%). The basic characterization of HWSPs was determined by using the FTIR. These preliminary in vitro biological studies indicated that lemongrass polysaccharides were useful for anticancer therapy. Copyright © 2014 Elsevier B.V. All rights reserved.

Advancements in meat packaging.

PubMed

McMillin, Kenneth W

2017-10-01

Packaging of meat provides the same or similar benefits for raw chilled and processed meats as other types of food packaging. Although air-permeable packaging is most prevalent for raw chilled red meat, vacuum and modified atmosphere packaging offer longer shelf life. The major advancements in meat packaging have been in the widely used plastic polymers while biobased materials and their integration into composite packaging are receiving much attention for functionality and sustainability. At this time, active and intelligent packaging are not widely used for antioxidant, antimicrobial, and other functions to stabilize and enhance meat properties although many options are being developed and investigated. The advances being made in nanotechnology will be incorporated into food packaging and presumably into meat packaging when appropriate and useful. Intelligent packaging using sensors for transmission of desired information and prompting of subsequent changes in packaging materials, environments or the products to maintain safety and quality are still in developmental stages. Copyright © 2017 Elsevier Ltd. All rights reserved.

Static Thermochemical Model of COREX Melter Gasifier

NASA Astrophysics Data System (ADS)

Srishilan, C.; Shukla, Ajay Kumar

2018-02-01

COREX is one of the commercial smelting reduction processes. It uses the finer size ore and semi-soft coal instead of metallurgical coke to produce hot metal from iron ore. The use of top gas with high calorific value as a by-product export gas makes the process economical and green. The predictive thermochemical model of the COREX process presented here enables rapid computation of process parameters such as (1) required amount of ore, coal, and flux; (2) amount of slag and gas generated; and (3) gas compositions (based on the raw material and desired hot metal quality). The model helps in predicting the variations in process parameters with respect to the (1) degree of metallization and (2) post-combustion ratio for given raw material conditions. In general reduction in coal, flux, and oxygen, the requirement is concomitant with an increase in the degree of metallization and post-combustion ratio. The model reported here has been benchmarked using industrial data obtained from the JSW Steel Plant, India.

Blackberry wines mineral and heavy metal content determination after dry ashing: multivariate data analysis as a tool for fruit wine quality control.

PubMed

Amidžić Klarić, Daniela; Klarić, Ilija; Mornar, Ana; Velić, Darko; Velić, Natalija

2015-08-01

This study brings out the data on the content of 21 mineral and heavy metal in 15 blackberry wines made of conventionally and organically grown blackberries. The objective of this study was to classify the blackberry wine samples based on their mineral composition and the applied cultivation method of the starting raw material by using chemometric analysis. The metal content of Croatian blackberry wine samples was determined by AAS after dry ashing. The comparison between an organic and conventional group of investigated blackberry wines showed statistically significant difference in concentrations of Si and Li, where the organic group contained higher concentrations of these compounds. According to multivariate data analysis, the model based on the original metal content data set finally included seven original variables (K, Fe, Mn, Cu, Ba, Cd and Cr) and gave a satisfactory separation of two applied cultivation methods of the starting raw material.

Evaluation of P{sub 2}O{sub 5} distribution inside the main clinker minerals by the application of EPMA method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ifka, Tomáš, E-mail: tomas.ifka@savba.sk; Palou, Martin; Baraček, Jan

2014-05-01

The formation of Portland clinker phases has taken place in thermodynamically non-equilibrium state between macro-oxides CaO, SiO{sub 2}, Al{sub 2}O{sub 3}, Fe{sub 2}O{sub 3} and MgO from raw meal and P{sub 2}O{sub 5} from bone meal. The paper deals with the study of clinker minerals as solid solutions with P{sub 2}O{sub 5} during the clinkerization of raw mixture containing bone meal (BM). The ash of BM has contributed as a raw material to the formation of different clinker phases. Electron probe microanalysis (EPMA) method was used to determine the preferential distribution of P{sub 2}O{sub 5} inside calcium silicate phases andmore » its influence upon C{sub 2}S/C{sub 3}S ratio. Basing on these results, composition of solid solution of C{sub 2}S and C{sub 3}S was established.« less

Influence of composition of diluent on populations of yeasts and moulds recovered from raw fruits.

PubMed

Beuchat, L R; Scouten, A J; Jablonska, J

2002-01-01

The aims of this study were (i) to determine the retention of viability of mycoflora removed from raw fruits, and how this affected diluents used to prepare samples for enumeration of propagules, and (ii) to evaluate the performance of recovery media for supporting colony development. Yeasts and moulds removed from seven types of raw fruit were held in seven diluents for 1 h before plating on dichloran rose bengal chloramphenicol (DRBC) agar and plate count agar supplemented with chloramphenicol (100 micro g ml-1) (PCAC). Significant reductions (P=0.05) in populations of yeasts, moulds, and yeasts plus moulds occurred within the 1 h holding period, regardless of diluent composition. Overall, retention of viability was not influenced by diluent composition, and neither DRBC agar nor PCAC were superior in supporting colony development. The composition of diluents used to prepare food samples for mycological analysis has little affect on the number of yeasts and moulds recovered from seven types of naturally contaminated raw fruit. Both DRBC agar and PCAC are suitable as enumeration media. Diluents and media most often recommended for enumerating yeasts and moulds in foods are appropriate for raw fruits.

Effects of extract liquid of SLS made from three different materials on seed germination and seedling growth of rice

NASA Astrophysics Data System (ADS)

Shao, Lingzhi; Fu, Wenting; Liu, Hong; Yan, Min; Li, Leyuan

Rice and wheat are the main candidate crops in the bioregenerative life support system (BLSS) of China, for they are traditional food in Asia. Thus the recycling of their straws is an important issue in our BLSS, and it is a vital way to biologically process them into the soil like substrate (SLS) first and then reuse them in the plant cultivation system to achieve their recycle in BLSS. However, rice is a plant with strong allelopathic effects. And so far, it is also not clear that what kind of raw materials can be processed into proper SLS to grow rice in the BLSS. Therefore, in this study, the extract liquid of SLS made from three different materials including rice straw, wheat straw and rice-wheat mixed straw was utilized to investigate its effects on the seed germination and seedling growth of rice. The gradients of the extract concentrations (soil: water) were 1:3, 1:5, 1:9, and 1:15 with the deionized water used as control. The effects of different types of SLS on seed germination and seedling vitality of rice were confirmed by analyzing the germination rate, seedling length, root length, root fresh weight, seedling fresh weight and other indicates. In addition, based on the analysis towards pH, organic matter composition and other factors of the SLS as well as the chlorophyll and hormone content of rice, the mechanism of the inhibition was speculated and the preventive methods of this phenomenon was explored. Finally, the feasibility of cultivating rice on the SLS made from the above three kinds of raw materials was evaluated and the proper raw materials to be processed into SLS to grow rice were determined.

Petrographic microscope investigation of mortar and ceramic technologies for the conservation of the built heritage

NASA Astrophysics Data System (ADS)

Pavia, S.; Caro, S.

2007-07-01

Polarised-light (or petrographic) microscopy has been widely applied to heritage materials to assess composition and diagnose damage. However, instead, this paper focuses on the petrographic investigation of brick and mortar technologies for the production of quality repair materials compatible with their adjacent fabrics. Furthermore, the paper relates production technologies to the physical properties of the materials fabricated, and thus their final quality and durability. According to Cesare Brandi´s theory of compatibility (the 20th century architect on whose work modern conservation theory and practice are largely based) existing historic materials should be replaced with their equivalent. This paper demonstrates that polarised-light microscopy provides data on the origin and nature of raw materials, and processing parameters such as blending, mixing, firing, calcination and slaking, and how these relate to the quality of the final product. In addition, this paper highlights the importance of production technologies as these directly impact the physical properties of the materials fabricated and thus determine their final quality and durability. In this context, the paper investigates mortar calcination and slaking, two important operations in the manufacture of building limes that govern the reactivity, shrinkage and water retention of a lime binder which will impact mortar's properties such as workability, plasticity and carbonation speed, and these in turn will determine the ease of execution, durability and strength of a lime mortar. Petrographic analysis also provides evidence of ceramic technology including identification of local or foreign production and processing parameters such as sieving, blending, mixing and firing. A petrographic study of the ceramic matrix coupled to the diagnosis of mineral phases formed during firing allows to quantify sintering and vitrification and thus determine firing temperatures. Finally, certain features of the raw clay such as the grading and the amount and nature of the non-plastic material inform, not only on the raw material's origin, but also impact the physical properties of the ceramic ware.

Characterization and quantification of N-(3-aminopropyl)-N-dodecyl-1,3-propanediamine biocide by NMR, HPLC/MS and titration techniques.

PubMed

Mondin, Andrea; Bogialli, Sara; Venzo, Alfonso; Favaro, Gabriella; Badocco, Denis; Pastore, Paolo

2014-01-01

The present paper reports the determination of the tri-amine N-(3-aminopropyl)-N-dodecyl-1,3-propanediamine (TA) present in a raw material called LONZABAC used to formulate various, widely used commercial biocides. The active principle, TA, is present in LONZABAC together with other molecules at lower concentration levels. Three independent analytical approaches, namely solution NMR spectroscopy, liquid chromatography coupled to high resolution mass spectrometry (LC/HRMS) and acid-base titration in mixed solvent, were used to overcome the problem of the non-availability of the active principle as high purity standard. NMR analysis of raw material, using a suitable internal standard, evidenced in all analyzed lots the presence of the active principle, the N-dodecyl-1,3-propanediamine (DA) and the n-dodecylamine (MA) and the absence of non-organic, NMR-inactive species. NMR peak integration led to a rough composition of the MA:DA:TA as 1:9:90. The LC/HRMS analysis allowed the accurate determination of DA and MA and confirmed in all samples the presence of the TA, which was estimated by difference: MA=1.4±0.3%, DA=11.1±0.7%, TA=87.5±1.3%. The obtained results were used to setup an easy, rapid and cheap acid-base titration method able to furnish a sufficiently accurate evaluation of the active principle both in the raw material and in diluted commercial products. For the raw material the results were: TA+MA=91.1±0.8% and DA-MA=8.9±0.8%, statistically coherent with LC/MS ones. The LC/MS approach demonstrated also its great potentialities to recognize trace of the biocide components both in environmental samples and in the formulated commercial products. Copyright © 2013 Elsevier Ltd. All rights reserved.

7 CFR 58.332 - Segregation of raw material.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Segregation of raw material. 58.332 Section 58.332 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Procedures § 58.332 Segregation of raw material. The milk and cream received at the dairy plant shall meet...

7 CFR 58.332 - Segregation of raw material.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Segregation of raw material. 58.332 Section 58.332 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Procedures § 58.332 Segregation of raw material. The milk and cream received at the dairy plant shall meet...

77 FR 2662 - Airworthiness Directives; Bombardier, Inc. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-19

... to batches of raw material that did not meet required tensile strength. This proposed AD would..., Avox Systems Inc., revealed that the deformation was attributed to two (2) batches of raw material that... regulator on the oxygen cylinder, which was attributed to batches of raw material that did not meet required...

77 FR 31174 - Airworthiness Directives; Bombardier, Inc. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

..., which was attributed to batches of raw material that did not meet required tensile strength. This AD... the deformation was attributed to two (2) batches of raw material that did not meet the required... deformation of the pressure regulator on the oxygen cylinder, which was attributed to batches of raw material...

Rice straw-wood particle composite for sound absorbing wooden construction materials.

PubMed

Yang, Han-Seung; Kim, Dae-Jun; Kim, Hyun-Joong

2003-01-01

In this study, rice straw-wood particle composite boards were manufactured as insulation boards using the method used in the wood-based panel industry. The raw material, rice straw, was chosen because of its availability. The manufacturing parameters were: a specific gravity of 0.4, 0.6, and 0.8, and a rice straw content (10/90, 20/80, and 30/70 weight of rice straw/wood particle) of 10, 20, and 30 wt.%. A commercial urea-formaldehyde adhesive was used as the composite binder, to achieve 140-290 psi of bending modulus of rupture (MOR) with 0.4 specific gravity, 700-900 psi of bending MOR with 0.6 specific gravity, and 1400-2900 psi of bending MOR with a 0.8 specific gravity. All of the composite boards were superior to insulation board in strength. Width and length of the rice straw particle did not affect the bending MOR. The composite boards made from a random cutting of rice straw and wood particles were the best and recommended for manufacturing processes. Sound absorption coefficients of the 0.4 and 0.6 specific gravity boards were higher than the other wood-based materials. The recommended properties of the rice straw-wood particle composite boards are described, to absorb noises, preserve the temperature of indoor living spaces, and to be able to partially or completely substitute for wood particleboard and insulation board in wooden constructions.

Influence of man-made aluminosilicate raw materials on physical and mechanical properties of building materials.

NASA Astrophysics Data System (ADS)

Volodchenko, A. A.; Lesovik, V. S.; Stoletov, A. A.; Glagolev, E. S.; Volodchenko, A. N.; Magomedov, Z. G.

2018-03-01

It has been identified that man-made aluminosilicate raw materials represented by clay rock of varied genesis can be used as energy-efficient raw materials to obtain efficient highly-hollow non-autoclaved silicate materials. A technique of structure formation in the conditions of pressureless steam treatment has been offered. Cementing compounds of non- autoclaved silicate materials based on man-made aluminosilicate raw materials possess hydraulic properties that are conditioned by the process of further formation and recrystallization of calcium silicate hydrates, which optimizes the ratio between gellike and crystalline components and densifies the cementing compound structure, which leads to improvement of performance characteristics. Increasing the performance characteristics of the obtained products is possible by changing the molding conditions. For this reason, in order to create high-density material packaging and, as a result, to increase the strength properties of the products, it is reasonable to use higher pressure, under which raw brick is formed, which will facilitate the increase of quality of highly-hollow products.

76 FR 62447 - Importer of Controlled Substances; Notice of Registration

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... narcotic raw material are not appropriate. With regard to all non-Narcotic Raw Material drugs on this...-phenethyl-4-piperidine (8333)... II Phenylacetone (8501) II Opium, raw (9600) II Poppy Straw Concentrate...

Short communication: Variation in the composition and properties of Swedish raw milk for ultra-high-temperature processing.

PubMed

Karlsson, Maria A; Langton, Maud; Innings, Fredrik; Wikström, Malin; Lundh, Åse Sternesjö

2017-04-01

The composition and properties of raw milk are of great importance for the quality and shelf life of the final dairy product, especially in products with a long shelf life [e.g., ultra-high-temperature (UHT)-treated milk]. The objective of this study was to investigate the compositional variation in raw milk samples before processing at the dairy plant. Moreover, we wanted to investigate the effect of the UHT process on this variation (i.e., if the same variation could be observed in the corresponding UHT milk). The quality traits analyzed included detailed milk composition, counts of total and psychrotrophic bacteria, proteolytic activity, and color, as well as predictive measures of stability (i.e., ethanol stability and heat coagulating time). Samples of raw milk and the corresponding produced UHT milk were collected and analyzed on a monthly basis during 1 yr. Principal component analysis was used to identify months showing similarities and differences with respect to total variation. In contrast to previous studies, we observed only small variations between months and no clear effect of season for the raw milk. For the UHT milk, July and the winter months (December, January, and February) tended to separate from the other months. Quality traits showing significant variation were only to some extent identical in raw milk and UHT-processed milk. A better understanding of the natural variation in raw milk quality will provide opportunities to improve the shelf life of UHT-treated milk products. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Multiply fully recyclable carbon fibre reinforced heat-resistant covalent thermosetting advanced composites

NASA Astrophysics Data System (ADS)

Yuan, Yanchao; Sun, Yanxiao; Yan, Shijing; Zhao, Jianqing; Liu, Shumei; Zhang, Mingqiu; Zheng, Xiaoxing; Jia, Lei

2017-03-01

Nondestructive retrieval of expensive carbon fibres (CFs) from CF-reinforced thermosetting advanced composites widely applied in high-tech fields has remained inaccessible as the harsh conditions required to recycle high-performance resin matrices unavoidably damage the structure and properties of CFs. Degradable thermosetting resins with stable covalent structures offer a potential solution to this conflict. Here we design a new synthesis scheme and prepare a recyclable CF-reinforced poly(hexahydrotriazine) resin matrix advanced composite. The multiple recycling experiments and characterization data establish that this composite demonstrates performance comparable to those of its commercial counterparts, and more importantly, it realizes multiple intact recoveries of CFs and near-total recycling of the principal raw materials through gentle depolymerization in certain dilute acid solution. To our best knowledge, this study demonstrates for the first time a feasible and environment-friendly preparation-recycle-regeneration strategy for multiple CF-recycling from CF-reinforced advanced composites.

Multiply fully recyclable carbon fibre reinforced heat-resistant covalent thermosetting advanced composites.

PubMed

Yuan, Yanchao; Sun, Yanxiao; Yan, Shijing; Zhao, Jianqing; Liu, Shumei; Zhang, Mingqiu; Zheng, Xiaoxing; Jia, Lei

2017-03-02

Nondestructive retrieval of expensive carbon fibres (CFs) from CF-reinforced thermosetting advanced composites widely applied in high-tech fields has remained inaccessible as the harsh conditions required to recycle high-performance resin matrices unavoidably damage the structure and properties of CFs. Degradable thermosetting resins with stable covalent structures offer a potential solution to this conflict. Here we design a new synthesis scheme and prepare a recyclable CF-reinforced poly(hexahydrotriazine) resin matrix advanced composite. The multiple recycling experiments and characterization data establish that this composite demonstrates performance comparable to those of its commercial counterparts, and more importantly, it realizes multiple intact recoveries of CFs and near-total recycling of the principal raw materials through gentle depolymerization in certain dilute acid solution. To our best knowledge, this study demonstrates for the first time a feasible and environment-friendly preparation-recycle-regeneration strategy for multiple CF-recycling from CF-reinforced advanced composites.

A facile solvothermal method to produce graphene-ZnS composites for superior photoelectric applications

NASA Astrophysics Data System (ADS)

Lei, Yun; Chen, Feifei; Li, Rong; Xu, Jun

2014-07-01

In this experiment, flake graphite (<30 μm) was prepared as raw materials. Graphite oxide is prepared with Hummers method by low temperature, middle temperature and high temperature, and further treated with super-sonic oscillation to get graphene oxide. Graphene-zinc sulfide composites were synthesized through a simple solvothermal method using thiourea or sodium sulfide as sulfur source in the ethylene glycol or ethylenediamine, respectively. The products were characterized by X-ray and SEM, and analyzed by the transient photocurrent response and electrochemical impedance spectra. The results indicate that the properties of graphene-zinc sulfide composites prepared with thiourea in ethylene glycol are superior to those of blank-ZnS and composites prepared with sodium sulfide and ethylenediamine, which is attributed to electron capture and transfer ability of graphene resulting in a more efficient separation of the photoexcited charge carriers from ZnS-graphene composites.

Multiply fully recyclable carbon fibre reinforced heat-resistant covalent thermosetting advanced composites

PubMed Central

Yuan, Yanchao; Sun, Yanxiao; Yan, Shijing; Zhao, Jianqing; Liu, Shumei; Zhang, Mingqiu; Zheng, Xiaoxing; Jia, Lei

2017-01-01

Nondestructive retrieval of expensive carbon fibres (CFs) from CF-reinforced thermosetting advanced composites widely applied in high-tech fields has remained inaccessible as the harsh conditions required to recycle high-performance resin matrices unavoidably damage the structure and properties of CFs. Degradable thermosetting resins with stable covalent structures offer a potential solution to this conflict. Here we design a new synthesis scheme and prepare a recyclable CF-reinforced poly(hexahydrotriazine) resin matrix advanced composite. The multiple recycling experiments and characterization data establish that this composite demonstrates performance comparable to those of its commercial counterparts, and more importantly, it realizes multiple intact recoveries of CFs and near-total recycling of the principal raw materials through gentle depolymerization in certain dilute acid solution. To our best knowledge, this study demonstrates for the first time a feasible and environment-friendly preparation-recycle-regeneration strategy for multiple CF-recycling from CF-reinforced advanced composites. PMID:28251985

Raw materials in the manufacture of biotechnology products: regulatory considerations.

PubMed

Cordoba-Rodriguez, Ruth

2010-01-01

The Food and Drug Administration's Pharmaceutical cGMPs for the 21st Century initiative emphasizes science and risk-based approaches in the manufacture of drugs. These approaches are reflected in the International Conference on Harmonization (ICH) guidances ICH Q8, Q9, and Q10 and encourage a comprehensive assessment of the manufacture of a biologic, including all aspects of manufacture that have the potential to affect the finished drug product. Appropriate assessment and management of raw materials are an important part of this initiative. Ideally, a raw materials program should strive to assess and minimize the risk to product quality. With this in mind, risk-assessment concepts and control strategies will be discussed and illustrated by examples, with an emphasis on the impact of raw materials on cell substrates. Finally, the life cycle of the raw material will be considered, including its potential to affect the drug product life cycle. In this framework, the supply chain and the vendor-manufacturer relationship will be explored as important parts of an adequate raw materials control strategy.

Worldwide Mycotoxins Exposure in Pig and Poultry Feed Formulations

PubMed Central

Guerre, Philippe

2016-01-01

The purpose of this review is to present information about raw materials that can be used in pig and poultry diets and the factors responsible for variations in their mycotoxin contents. The levels of mycotoxins in pig and poultry feeds are calculated based on mycotoxin contamination levels of the raw materials with different diet formulations, to highlight the important role the stage of production and the raw materials used can have on mycotoxins levels in diets. Our analysis focuses on mycotoxins for which maximum tolerated levels or regulatory guidelines exist, and for which sufficient contamination data are available. Raw materials used in feed formulation vary considerably depending on the species of animal, and the stage of production. Mycotoxins are secondary fungal metabolites whose frequency and levels also vary considerably depending on the raw materials used and on the geographic location where they were produced. Although several reviews of existing data and of the literature on worldwide mycotoxin contamination of food and feed are available, the impact of the different raw materials used on feed formulation has not been widely studied. PMID:27886128

Large-scale production of PMMA/SWCNT composites based on SWCNT modified with PMMA.

PubMed

Fraser, Robin Anderson; Stoeffler, Karen; Ashrafi, Behnam; Zhang, Yunfa; Simard, Benoit

2012-04-01

In this work, a two-step method consisting of in situ polymerization of polymethyl methacrylate (PMMA) in the presence of single-walled carbon nanotubes (SWCNT), followed by the redispersion of the resulting compound in dimethylformamide (DMF), was used to fabricate SWCNT modified with PMMA (SWCNT-PMMA). Raman spectroscopy revealed that PMMA was merely wrapped around the SWCNT when raw SWCNT or purified SWCNT were used as the starting material. However, PMMA was covalently bonded to SWCNT when acid treated SWCNT (SWCNT-COOH) was used as the starting material. SWCNT-PMMA compounds were further diluted in pure PMMA by conventional melt compounding at large scale (several kilograms) to obtain transparent composites containing 0.09 wt % SWCNT. The micro- and nano-dispersion of the SWCNT in the composites were analyzed using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The thermal and mechanical properties of the composites were determined by thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), tensile testing, and Charpy impact testing. At the the low SWCNT loading studied, the tensile properties remain unchanged, whereas the impact strength improves by 20%.

Effect of Processing Conditions on Fracture Resistance and Cohesive Laws of Binderfree All-Cellulose Composites

NASA Astrophysics Data System (ADS)

Goutianos, S.; Arévalo, R.; Sørensen, B. F.; Peijs, T.

2014-12-01

The fracture properties of all-cellulose composites without matrix were studied using Double Cantilever Beam (DCB) sandwich specimens loaded with pure monotonically increasing bending moments, which give stable crack growth. The experiments were conducted in an environmental scanning electron microscope to a) perform accurate measurements of both the fracture energy for crack initiation and the fracture resistance and b) observe the microscale failure mechanisms especially in the the wake of the crack tip. Since the mechanical behaviour of the all-cellulose composites was non-linear, a general method was first developed to obtain fracture resistance values from the DCB specimens taking into account the non-linear material response. The binderfree all-cellulose composites were prepared by a mechanical refinement process that allows the formation of intramolecular bonds between the cellulose molecules during the drying process. Defibrilation of the raw cellulose material is done in wet medium in a paper-like process. Panels with different refining time were tested and it was found than an increase in fibre fibrillation results in a lower fracture resistance.

Raw material ‘criticality’—sense or nonsense?

NASA Astrophysics Data System (ADS)

Frenzel, M.; Kullik, J.; Reuter, M. A.; Gutzmer, J.

2017-03-01

The past decade has seen a resurgence of interest in the supply security of mineral raw materials. A key to the current debate is the concept of ‘criticality’. The present article reviews the criticality concept, as well as the methodologies used in its assessment, including a critical evaluation of their validity in view of classical risk theory. Furthermore, it discusses a number of risks present in global raw materials markets that are not captured by most criticality assessments. Proposed measures for the alleviation of these risks are also presented. We find that current assessments of raw material criticality are fundamentally flawed in several ways. This is mostly due to a lack of adherence to risk theory, and highly limits their applicability. Many of the raw materials generally identified as critical are probably not critical. Still, the flaws of current assessments do not mean that the general issue of supply security can simply be ignored. Rather, it implies that new assessments are required. While the basic theoretical framework for such assessments is outlined in this review, detailed method development will require a major collaborative effort between different disciplines along the raw materials value chain. In the opinion of the authors, the greatest longer-term challenge in the raw materials sector is to stop, or counteract the effects of, the escalation of unit energy costs of production. This issue is particularly pressing due to its close link with the renewable energy transition, requiring more metal and mineral raw materials per unit energy produced. The solution to this problem will require coordinated policy action, as well as the collaboration of scientists from many different fields—with physics, as well as the materials and earth sciences in the lead.

Process Parameter Optimization of Extrusion-Based 3D Metal Printing Utilizing PW-LDPE-SA Binder System.

PubMed

Ren, Luquan; Zhou, Xueli; Song, Zhengyi; Zhao, Che; Liu, Qingping; Xue, Jingze; Li, Xiujuan

2017-03-16

Recently, with a broadening range of available materials and alteration of feeding processes, several extrusion-based 3D printing processes for metal materials have been developed. An emerging process is applicable for the fabrication of metal parts into electronics and composites. In this paper, some critical parameters of extrusion-based 3D printing processes were optimized by a series of experiments with a melting extrusion printer. The raw materials were copper powder and a thermoplastic organic binder system and the system included paraffin wax, low density polyethylene, and stearic acid (PW-LDPE-SA). The homogeneity and rheological behaviour of the raw materials, the strength of the green samples, and the hardness of the sintered samples were investigated. Moreover, the printing and sintering parameters were optimized with an orthogonal design method. The influence factors in regard to the ultimate tensile strength of the green samples can be described as follows: infill degree > raster angle > layer thickness. As for the sintering process, the major factor on hardness is sintering temperature, followed by holding time and heating rate. The highest hardness of the sintered samples was very close to the average hardness of commercially pure copper material. Generally, the extrusion-based printing process for producing metal materials is a promising strategy because it has some advantages over traditional approaches for cost, efficiency, and simplicity.

Process Parameter Optimization of Extrusion-Based 3D Metal Printing Utilizing PW–LDPE–SA Binder System

PubMed Central

Ren, Luquan; Zhou, Xueli; Song, Zhengyi; Zhao, Che; Liu, Qingping; Xue, Jingze; Li, Xiujuan

2017-01-01

Recently, with a broadening range of available materials and alteration of feeding processes, several extrusion-based 3D printing processes for metal materials have been developed. An emerging process is applicable for the fabrication of metal parts into electronics and composites. In this paper, some critical parameters of extrusion-based 3D printing processes were optimized by a series of experiments with a melting extrusion printer. The raw materials were copper powder and a thermoplastic organic binder system and the system included paraffin wax, low density polyethylene, and stearic acid (PW–LDPE–SA). The homogeneity and rheological behaviour of the raw materials, the strength of the green samples, and the hardness of the sintered samples were investigated. Moreover, the printing and sintering parameters were optimized with an orthogonal design method. The influence factors in regard to the ultimate tensile strength of the green samples can be described as follows: infill degree > raster angle > layer thickness. As for the sintering process, the major factor on hardness is sintering temperature, followed by holding time and heating rate. The highest hardness of the sintered samples was very close to the average hardness of commercially pure copper material. Generally, the extrusion-based printing process for producing metal materials is a promising strategy because it has some advantages over traditional approaches for cost, efficiency, and simplicity. PMID:28772665

Magnetic iron oxides in the cementation technology of the boron-containing radioactive waste

NASA Astrophysics Data System (ADS)

Fedotov, M. A.; Gorbunova, O. A.; Fedorova, O. V.; Folmanis, G. E.; Kovalenko, L. V.

2015-04-01

Two ways of synthesis of non-detachable dispersed particles of magnetic materials useful for the boron-containing waste cementation process regulation were developed. Powder XRD showed that the method of carbothermic recovery of nanoscale iron hydroxide allows obtaining a mixture of iron oxides with content of the magnetic phase up to 70%. Method of low-temperature hydrogen reduction of the raw materials allows obtaining various compositions of a-iron and iron oxides with the possibility to change the size of the final particles in a wide range. The possibility of using composites of magnetic iron oxides and metal oxide compositions instead of ferromagnetic rods with VEP of boron-containing liquid radioactive waste in the fluidized field was studied. It was shown that the use of fine and nano particles of the iron oxides in the pre-treatment of the boron-containing LRW increases the strength of the final compounds and accelerates the cement setting compounds from 13 to 5-9 days.

RSRM-13 (360Q013) ballistics mass properties flight designation STS-41

NASA Technical Reports Server (NTRS)

Laubacher, Brian A.; Richards, M. C.

1990-01-01

The propulsion performance and reconstructed mass properties data from Thiokol's RSRM-13 motors which were assigned to the STS-41 launch are presented. The SRM propellant, TP-H1148, is a composite type solid propellant, formulated of polybutadiene acrylic acid acryonitrile terpolymer binder, epoxy curing agent, ammonium perchlorate oxidizer, and aluminum powder fuel. A small amount of burning rate catalyst (iron oxide) was added to achieve the desired propellant burn rate. The propellant evaluation and raw material information are also presented. The presented ballistic performance was based on the Operational Flight Instrumentation. The adjustments made to the raw data on this flight include biasing the data to correct ambient pressure before liftoff. The performance from each motor as well as matched pair performance values were well within the CEI Specification requirements.

Nondestructive determination of activity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chabalier, B.

1996-08-01

Characterization and appraisal tests include the measurement of activity in raw waste and waste packages. After conditioning, variations in density, matrix composition, and geometry make evaluation of the radionuclide activity in a package destined for storage nearly impossible without measurements and with a low uncertainty. Various nondestructive measuring techniques that use ionizing radiation are employed to characterize waste packages and raw waste. Gamma spectrometry is the most widely used technique because of its simple operation and low cost. This technique is used to quantify the beta-gamma and alpha activity of gamma-emitting radionuclides as well as to check the radioactive homogeneitymore » of the waste packages. Numerous systems for directly measuring waste packages have been developed. Two types of methods may be distinguished, depending on whether results that come from the measurements are weighted by an experimentally determined corrective term or by calculation. Through the MARCO and CARACO measuring systems, a method is described that allows one to quantify the activity of the beta-gamma and alpha radionuclides contained in either a waste package or raw waste whose geometries and material compositions are more or less accurately known. This method is based on (a) measurement by gamma spectrometry of the beta-gamma and alpha activity of the gamma-emitting radionuclides contained in the waste package and (b) the application of calculated corrections; thus, the limitations imposed by reference package geometry and matrix are avoided.« less

Preparation of new diatomite-chitosan composite materials and their adsorption properties and mechanism of Hg(II).

PubMed

Fu, Yong; Xu, Xiaoxu; Huang, Yue; Hu, Jianshe; Chen, Qifan; Wu, Yaoqing

2017-12-01

A new composite absorbent with multifunctional and environmental-friendly structures was prepared using chitosan, diatomite and polyvinyl alcohol as the raw materials, and glutaraldehyde as a cross-linking agent. The structure and morphology of the composite absorbent, and its adsorption properties of Hg(II) in water were characterized with Fourier transform infrared (FT-IR) spectra, scanning electron microscope (SEM), X-ray diffraction (XRD), Brunauer Emmett Teller (BET) measurements and ultraviolet-visible (UV-Vis) spectra. The effect of the pH value and contact time on the removal rate and absorbance of Hg(II) was discussed. The adsorption kinetic model and static adsorption isotherm and regeneration of the obtained composite absorbent were investigated. The results indicated that the removal of Hg(II) on the composite absorbent followed a rapid adsorption for 50 min, and was close to the adsorption saturation after 1 h, which is in accord with the Langmuir adsorption isotherm model and the pseudo-second-order kinetic model. When the pH value, contact time and the mass of the composite absorbent was 3, 1 h and 100 mg, respectively, the removal rate of Hg(II) on the composite absorbent reached 77%, and the maximum adsorption capacity of Hg(II) reached 195.7 mg g -1 .

Preparation of new diatomite–chitosan composite materials and their adsorption properties and mechanism of Hg(II)

PubMed Central

Fu, Yong; Xu, Xiaoxu; Huang, Yue; Hu, Jianshe; Chen, Qifan; Wu, Yaoqing

2017-01-01

A new composite absorbent with multifunctional and environmental-friendly structures was prepared using chitosan, diatomite and polyvinyl alcohol as the raw materials, and glutaraldehyde as a cross-linking agent. The structure and morphology of the composite absorbent, and its adsorption properties of Hg(II) in water were characterized with Fourier transform infrared (FT-IR) spectra, scanning electron microscope (SEM), X-ray diffraction (XRD), Brunauer Emmett Teller (BET) measurements and ultraviolet–visible (UV–Vis) spectra. The effect of the pH value and contact time on the removal rate and absorbance of Hg(II) was discussed. The adsorption kinetic model and static adsorption isotherm and regeneration of the obtained composite absorbent were investigated. The results indicated that the removal of Hg(II) on the composite absorbent followed a rapid adsorption for 50 min, and was close to the adsorption saturation after 1 h, which is in accord with the Langmuir adsorption isotherm model and the pseudo-second-order kinetic model. When the pH value, contact time and the mass of the composite absorbent was 3, 1 h and 100 mg, respectively, the removal rate of Hg(II) on the composite absorbent reached 77%, and the maximum adsorption capacity of Hg(II) reached 195.7 mg g−1. PMID:29308226

Cellulose nanocrystals the next big nano-thing?

NASA Astrophysics Data System (ADS)

Postek, Michael T.; Vladar, Andras; Dagata, John; Farkas, Natalia; Ming, Bin; Sabo, Ronald; Wegner, Theodore H.; Beecher, James

2008-08-01

Biomass surrounds us from the smallest alga to the largest redwood tree. Even the largest trees owe their strength to a newly-appreciated class of nanomaterials known as cellulose nanocrystals (CNC). Cellulose, the world's most abundant natural, renewable, biodegradable polymer, occurs as whisker like microfibrils that are biosynthesized and deposited in plant material in a continuous fashion. Therefore, the basic raw materials for a future of new nanomaterials breakthroughs already abound in the environment and are available to be utilized in an array of future materials once the manufacturing processes and nanometrology are fully developed. This presentation will discuss some of the instrumentation, metrology and standards issues associated with nanomanufacturing of cellulose nanocrystals. The use of lignocellulosic fibers derived from sustainable, annually renewable resources as a reinforcing phase in polymeric matrix composites provides positive environmental benefits with respect to ultimate disposability and raw material use. Today we lack the essential metrology infrastructure that would enable the manufacture of nanotechnology-based products based on CNCs (or other new nanomaterial) to significantly impact the U.S. economy. The basic processes common to manufacturing - qualification of raw materials, continuous synthesis methods, process monitoring and control, in-line and off-line characterization of product for quality control purposes, validation by standard reference materials - are not generally in place for nanotechnology based products, and thus are barriers to innovation. One advantage presented by the study of CNCs is that, unlike other nanomaterials, at least, cellulose nanocrystal manufacturing is already a sustainable and viable bulk process. Literally tons of cellulose nanocrystals can be generated each day, producing other viable byproducts such as glucose (for alternative fuel) and gypsum (for buildings).There is an immediate need for the development of the basic manufacturing metrology infrastructure to implement fundamental best practices for manufacturing and in the determination of properties for these for nanoscale materials and the resultant products.

Renewable resources in the chemical industry--breaking away from oil?

PubMed

Nordhoff, Stefan; Höcker, Hans; Gebhardt, Henrike

2007-12-01

Rising prices for fossil-based raw materials suggest that sooner or later renewable raw materials will, in principle, become economically viable. This paper examines this widespread paradigm. Price linkages like those seen for decades particularly in connection with petrochemical raw materials are now increasingly affecting renewable raw materials. The main driving force is the competing utilisation as an energy source because both fossil-based and renewable raw materials are used primarily for heat, electrical power and mobility. As a result, prices are determined by energy utilisation. Simple observations show how prices for renewable carbon sources are becoming linked to the crude oil price. Whether the application calls for sugar, starch, virgin oils or lignocellulose, the price for the raw material rises with the oil price. Consequently, expectations regarding price trends for fossil-based energy sources can also be utilised for the valuation of alternative processes. However, this seriously calls into question the assumption that a rising crude oil price will favour the economic viability of alternative products and processes based on renewable raw materials. Conversely, it follows that these products and processes must demonstrate economic viability today. Especially in connection with new approaches in white biotechnology, it is evident that, under realistic assumptions, particularly in terms of achievable yields and the optimisation potential of the underlying processes, the route to utilisation is economically viable. This makes the paradigm mentioned at the outset at least very questionable.

Use of raw materials in the United States from 1900 through 2014

USGS Publications Warehouse

Matos, Grecia R.

2017-08-22

The economic growth of an industrialized nation such as the United States requires raw materials for construction (buildings, bridges, highways, and so forth), defense, and processing and manufacture of goods and services. Since the beginning of the 20th century, the types and quantities of raw materials used have increased and changed significantly. This fact sheet quantifies the amounts of raw materials (other than food and fuel) that have been used in the U.S. economy annually for a period of 115 years, from 1900 through 2014. It provides a broad overview of the quantity (weight) of nonfood and nonfuel materials used in the economy and illustrates the use and significance of raw nonfuel minerals in particular as building blocks of society.These data have been compiled to help the public and policymakers understand the changing annual flow of raw materials put into use in the United States. Such information can be helpful in assessing the potential effects of materials use on the environment, assessing materials’ intensity of use, and examining the role that these materials play in the economy. The data presented indicate the substitution and shift in materials usage from renewable to nonrenewable materials during the 20th century. The disaggregated quantities by commodity (not shown in this fact sheet) may be tested against supply adequacy and end of life issues.

Microstructures and Properties of 40Cu/Ag(Invar) Composites Fabricated by Powder Metallurgy and Subsequent Thermo-Mechanical Treatment

NASA Astrophysics Data System (ADS)

Zhang, Xin; Huang, Yingqiu; Liu, Xiangyu; Yang, Lei; Shi, Changdong; Wu, Yucheng; Tang, Wenming

2018-03-01

Composites of 40Cu/Ag(Invar) were prepared via pressureless sintering and subsequent thermo-mechanical treatment from raw materials of electroless Ag-plated Invar alloy powder and electrolytic Cu powder. Microstructures and properties of the prepared composites were studied to evaluate the effect of the Ag layer on blocking Cu/Invar interfacial diffusion in the composites. The electroless-plated Ag layer was dense, uniform, continuous, and bonded tightly with the Invar alloy substrate. During sintering of the composites, the Ag layer effectively prevented Cu/Invar interfacial diffusion. During cold-rolling, the Ag layer was deformed uniformly with the Invar alloy particles. The composites exhibited bi-continuous network structure and considerably improved properties. After sintering at 775 °C and subsequent thermo-mechanical treatment, the 40Cu/Ag(Invar) composites showed satisfactory comprehensive properties: relative density of 99.0 pct, hardness of HV 253, thermal conductivity of 55.7 W/(m K), and coefficient of thermal expansion of 11.2 × 10-6/K.

Fe3O4/C composite with hollow spheres in porous 3D-nanostructure as anode material for the lithium-ion batteries

NASA Astrophysics Data System (ADS)

Yang, Zhao; Su, Danyang; Yang, Jinping; Wang, Jing

2017-09-01

3d transition-metal oxides, especially Fe3O4, as anode materials for the lithium-ion batteries have been attracting intensive attentions in recent years due to their high energy capacity and low toxicity. A new Fe3O4/C composite with hollow spheres in porous three-dimensional (3D) nanostructure, which was synthesized by a facile solvothermal method using FeCl3·6H2O and porous spongy carbon as raw materials. The specific surface area and microstructures of composite were characterized by nitrogen adsorption-desorption isotherm method, FE-SEM and HR-TEM. A homogeneous distribution of hollow Fe3O4 spheres (diameter ranges from 120 nm to 150 nm) in the spongy carbon (pore size > 200 nm) conductive 3D-network significantly reduced the lithium-ion diffusion length and increased the electrochemical reaction area, and further more enhanced the lithium ion battery performance, such as discharge capacity and cycle life. As an anode material for the lithium-ion battery, the title composite exhibit excellent electrochemical properties. The Fe3O4/C composite electrode achieved a relatively high reversible specific capacity of 1450.1 mA h g-1 in the first cycle at 100 mA g-1, and excellent rate capability (69% retention at 1000 mA g-1) with good cycle stability (only 10% loss after 100 cycles).

Highly Stable and Flexible Pressure Sensors with Modified Multi-Walled Carbon Nanotube/Polymer Composites for Human Monitoring

PubMed Central

He, Yin; Ming, Yue; Li, Wei; Li, Yafang; Wu, Maoqi; Song, Jinzhong; Li, Xiaojiu; Liu, Hao

2018-01-01

A facile method for preparing an easy processing, repeatable and flexible pressure sensor was presented via the synthesis of modified multi-walled carbon nanotubes (m-MWNTs) and polyurethane (PU) films. The surface modification of multi-walled carbon nanotubes (MWNTs) simultaneously used a silane coupling agent (KH550) and sodium dodecyl benzene sulfonate (SDBS) to improve the dispersibility and compatibility of the MWNTs in a polymer matrix. The electrical property and piezoresistive behavior of the m-MWNT/PU composites were compared with raw multi-walled carbon nanotube (raw MWNT)/PU composites. Under linear uniaxial pressure, the m-MWNT/PU composite exhibited 4.282%kPa−1 sensitivity within the pressure of 1 kPa. The nonlinear error, hysteresis error and repeatability error of the piezoresistivity of m-MWNT/PU decreased 9%, 16.72% and 54.95% relative to raw MWNT/PU respectively. Therefore, the piezoresistive response of m-MWNT/PU had better stability than that of raw MWNT/PU composites. The m-MWNT/PU sensors could be utilized in wearable devices for body movement detection, monitoring of respiration and pressure detection in garments. PMID:29701643

Highly Stable and Flexible Pressure Sensors with Modified Multi-Walled Carbon Nanotube/Polymer Composites for Human Monitoring.

PubMed

He, Yin; Ming, Yue; Li, Wei; Li, Yafang; Wu, Maoqi; Song, Jinzhong; Li, Xiaojiu; Liu, Hao

2018-04-26

A facile method for preparing an easy processing, repeatable and flexible pressure sensor was presented via the synthesis of modified multi-walled carbon nanotubes (m-MWNTs) and polyurethane (PU) films. The surface modification of multi-walled carbon nanotubes (MWNTs) simultaneously used a silane coupling agent (KH550) and sodium dodecyl benzene sulfonate (SDBS) to improve the dispersibility and compatibility of the MWNTs in a polymer matrix. The electrical property and piezoresistive behavior of the m-MWNT/PU composites were compared with raw multi-walled carbon nanotube (raw MWNT)/PU composites. Under linear uniaxial pressure, the m-MWNT/PU composite exhibited 4.282%kPa −1 sensitivity within the pressure of 1 kPa. The nonlinear error, hysteresis error and repeatability error of the piezoresistivity of m-MWNT/PU decreased 9%, 16.72% and 54.95% relative to raw MWNT/PU respectively. Therefore, the piezoresistive response of m-MWNT/PU had better stability than that of raw MWNT/PU composites. The m-MWNT/PU sensors could be utilized in wearable devices for body movement detection, monitoring of respiration and pressure detection in garments.

Contamination of the cement raw material in a quarry site by seawater intrusion, Darica-Turkey

NASA Astrophysics Data System (ADS)

Camur, M. Zeki; Doyuran, Vedat

2008-02-01

The open pit mining nearby shoreline is planned to be extended into below sea level in order to use additional reserves of the cement raw material (marl). The raw material is currently contaminated by seawater intrusion below a depth of 20 m up to the distance of 90 m from shoreline. Seawater intrusion related contamination of the material used for the cement production was investigated by means of diffusion process for the future two below sea level mining scenarios covering 43 years of period. According to the results, chloride concentrations higher than the tolerable limit of a cement raw material would be present in the material about 10-25 cm inward from each discontinuity surface, controlling groundwater flow, located between 170 and 300 m landward from the shoreline at below sea level mining depths of 0-30 m. The estimations suggest that total amounts of dilution required for the contaminated raw material to reduce its concentration level to the tolerance limit with uncontaminated raw material are about 113- to 124-fold for scenario I (13 years of below sea level mining after 30 years of above sea level mining) and about 126- to 138-fold for scenario II (43 years of simultaneous above and below sea level minings).

Influence of Cellulosic Fibres on the Physical Properties of Fibre Cement Composites

NASA Astrophysics Data System (ADS)

Hospodarova, V.; Stevulova, N.; Vaclavik, V.; Dvorsky, T.

2017-10-01

Nowadays, there are new approaches directing to processing of non-conventional fibre-cement composites for application in the housing construction. Vegetable cellulosic fibres coming from natural resources used as reinforcement in cost-effective and environmental friendly building products are in the spotlight. The applying of natural fibres in cement based composites is narrowly linked to the ecological building sector, where a choice of materials is based on components including recyclable, renewable raw materials and low-resource manufacture techniques. In this paper, two types of cellulosic fibres coming from wood pulp and recycled waste paper with 0.2%; 0.3% and 0.5% of fibre addition into cement mixtures were used. Differences in the physical characteristics (flowability, density, coefficient of thermal conductivity and water absorbability) of 28 days hardened fibre-cement composites are investigated. Addition of cellulosic fibres to cement mixture caused worsening the workability of fresh mixture as well as absorbability of hardened composites due to hydrophilic nature of biomaterial, whereas density and thermal conductivity of manufactured cement based fibre plaster are enhanced. The physical properties of cement plasters based on cellulosic fibres depend on structural, physical characteristics of cellulosic fibres, their nature and processing.

77 FR 21532 - Glycine From the People's Republic of China: Preliminary Partial Affirmative Determination of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-10

... because it is producing glycine from raw materials of Indian origin and exporting such merchandise to the... find that there is no record evidence that AICO self produces glycine from Indian raw materials... exported to the United States glycine that it produced only from Indian raw materials. For a complete...

78 FR 69130 - Importer of Controlled Substances; Notice of Application: Johnson Matthey, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-18

... Concentrate (9670) II The company plans to import the listed controlled substances as raw materials, to be... requests for hearings on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007). In reference to the non-narcotic raw material, the company plans to import gram amounts to be used as...

Influence of ferrite phase in alite-calcium sulfoaluminate cements

NASA Astrophysics Data System (ADS)

Duvallet, Tristana Yvonne Francoise

Since the energy crisis in 1970's, research on low energy cements with low CO2- emissions has been increasing. Numerous solutions have been investigated, and the goal of this original research is to create a viable hybrid cement with the components of both Ordinary Portland cement (OPC) and calcium sulfoaluminate cement (CSAC), by forming a material that contains both alite and calcium sulfoaluminate clinker phases. Furthermore, this research focuses on keeping the cost of this material reasonable by reducing aluminum requirements through its substitution with iron. The aim of this work would produce a cement that can use large amounts of red mud, which is a plentiful waste material, in place of bauxite known as an expensive raw material. Modified Bogue equations were established and tested to formulate this novel cement with different amounts of ferrite, from 5% to 45% by weight. This was followed by the production of cement from reagent chemicals, and from industrial by-products as feedstocks (fly ash, red mud and slag). Hydration processes, as well as the mechanical properties, of these clinker compositions were studied, along with the addition of gypsum and the impact of a ferric iron complexing additive triisopropanolamine (TIPA). To summarize this research, the influence of the addition of 5-45% by weight of ferrite phase, was examined with the goal of introducing as much red mud as possible in the process without negatively attenuate the cement properties. Based on this PhD dissertation, the production of high-iron alite-calcium sulfoaluminateferrite cements was proven possible from the two sources of raw materials. The hydration processes and the mechanical properties seemed negatively affected by the addition of ferrite, as this phase was not hydrated entirely, even after 6 months of curing. The usage of TIPA counteracted this decline in strength by improving the ferrite hydration and increasing the optimum amount of gypsum required in each composition. The mechanical data were equivalent to OPC strengths for some compositions with 25% ferrite. This preliminary work constitutes the first research phase of this novel cement and requires additional research for its improvement. Topics for additional research are identified in this dissertation. KEYWORDS: alite, calcium sulfoaluminate, ferrite, low-energy cement, triisopropanolamine.

Utilization of open pit burned household waste ash--a feasibility study in Dhaka.

PubMed

Haque, Md Obaidul; Sharif, Ahmed

2014-05-01

Informal incineration or open pit burning of waste materials is a common practice in the peripheral area of Dhaka, one of the fastest growing mega-cities in the world. This study deals with the effect of open pit burned (i.e. open burned) household waste bottom ash on fired clay bricks. Between 0 to 50% (by weight) of open pit burned household waste bottom ash was mixed with clay to make bricks. The molded specimens were air-dried at room temperature for 24 h and then oven dried at 100 °C for another 24 h to remove the water. The raw bricks were fired in a muffle furnace to a designated temperature (800, 900 and 1000 °C, respectively). The firing behaviour (mechanical strength, water absorption and shrinkage) was determined. The microstructures, phase compositions and leachates were evaluated for bricks manufactured at different firing temperatures. These results demonstrate that open pit burned ash can be recycled in clay bricks. This study also presents physical observations of the incinerated ash particles and determination of the chemical compositions of the raw materials by wet analysis. Open pit burned ash can be introduced easily into bricks up to 20% wt. The concentrations of hazardous components in the leachates were below the standard threshold for inert waste category landfill and their environmental risk during their use-life step can be considered negligible.

Continuous fiber ceramic matrix composites for heat engine components

NASA Technical Reports Server (NTRS)

Tripp, David E.

1988-01-01

High strength at elevated temperatures, low density, resistance to wear, and abundance of nonstrategic raw materials make structural ceramics attractive for advanced heat engine applications. Unfortunately, ceramics have a low fracture toughness and fail catastrophically because of overload, impact, and contact stresses. Ceramic matrix composites provide the means to achieve improved fracture toughness while retaining desirable characteristics, such as high strength and low density. Materials scientists and engineers are trying to develop the ideal fibers and matrices to achieve the optimum ceramic matrix composite properties. A need exists for the development of failure models for the design of ceramic matrix composite heat engine components. Phenomenological failure models are currently the most frequently used in industry, but they are deterministic and do not adequately describe ceramic matrix composite behavior. Semi-empirical models were proposed, which relate the failure of notched composite laminates to the stress a characteristic distance away from the notch. Shear lag models describe composite failure modes at the micromechanics level. The enhanced matrix cracking stress occurs at the same applied stress level predicted by the two models of steady state cracking. Finally, statistical models take into consideration the distribution in composite failure strength. The intent is to develop these models into computer algorithms for the failure analysis of ceramic matrix composites under monotonically increasing loads. The algorithms will be included in a postprocessor to general purpose finite element programs.

A hazardous waste from secondary aluminium metallurgy as a new raw material for calcium aluminate glasses.

PubMed

López-Delgado, Aurora; Tayibi, Hanan; Pérez, Carlos; Alguacil, Francisco José; López, Félix Antonio

2009-06-15

A solid waste coming from the secondary aluminium industry was successfully vitrified in the ternary CaO-Al(2)O(3)-SiO(2) system at 1500 degrees C. This waste is a complex material which is considered hazardous because of its behaviour in the presence of water or moisture. In these conditions, the dust can generate gases such as H(2), NH(3), CH(4), H(2)S, along with heat and potential aluminothermy. Only silica sand and calcium carbonate were added as external raw materials to complete the glasses formula. Different nominal compositions of glasses, with Al(2)O(3) ranging between 20% and 54%, were studied to determine the glass forming area. The glasses obtained allow the immobilisation of up to 75% of waste in a multicomponent oxide system in which all the components of the waste are incorporated. The microhardness Hv values varied between 6.05 and 6.62GPa and the linear thermal expansion coefficient, alpha, varied between (62 and 139)x10(-7)K(-1). Several glasses showed a high hydrolytic resistance in deionised water at 98 degrees C.

Total flavonoids content in the raw material and aqueous extractives from Bauhinia monandra Kurz (Caesalpiniaceae).

PubMed

Fernandes, Ana Josane Dantas; Ferreira, Magda Rhayanny Assunção; Randau, Karina Perrelli; de Souza, Tatiane Pereira; Soares, Luiz Alberto Lira

2012-01-01

The aim of this work was to evaluate the spectrophotometric methodology for determining the total flavonoid content (TFC) in herbal drug and derived products from Bauhinia monandra Kurz. Several analytical parameters from this method grounded on the complex formed between flavonoids and AlCl₃ were evaluated such as herbal amount (0.25 to 1.25 g); solvent composition (ethanol 40 to 80%, v/v); as well as the reaction time and AlCl₃ concentration (2 to 9%, w/v). The method was adjusted to aqueous extractives and its performance studied through precision, linearity and preliminary robustness. The results showed an important dependence of the method response from reaction time, AlCl₃ concentration, sample amount, and solvent mixture. After choosing the optimized condition, the method was applied for the matrixes (herbal material and extractives), showing precision lower than 5% (for both parameters repeatability and intermediate precision), coefficient of determination higher than 0.99, and no important influence could be observed for slight variations from wavelength or AlCl₃ concentration. Thus, it could be concluded that the evaluated analytical procedure was suitable to quantify the total flavonoid content in raw material and aqueous extractives from leaves of B. monandra.

Synthesis, Characterization and Application of N-Ti/13X/MCM-41 Mesoporous Molecular Sieves.

PubMed

Tao, Hong; Nguyen, Nhat-Thien; Hei, Xiao-Hui; Nguyen, Cong Nguyen; Tsai, Hsiao-Hsin; Chang, I-Cheng; Chang, Chang-Tang

2016-06-01

Di-n-butyl phthalate (DBP) is a type of phthalate ester. In recent years, an increasing number of studies have examined the removal of DBP. In this study we use a composite material of N-Ti/13X/MCM-41, synthesized by nitrogen, molecular sieve 13X, tetrabutyl orthotitanate and tetraethyl orthosilicate as raw materials, CTAB as a structural template and tetrabutyl titanate and urea under hydrothermal conditions. The optimized experimental conditions, such as the amount of material, reaction time, pH value and initial concentration were tested. The surface areas of N-Ti/13X/MCM-41 were found to be 664 m2g(-1). TEM micrographs revealed N-Ti/13X/MCM-41 is consisting of aggregates of spherical particles, similar with standard synthesized MCM-41 (Mobil Composition of Matter No. 41). Through photocatalytic degradation experiments, the optimum degradation efficiency of DBP was more than 90% at a pH 6.0 with catalyst dosing of 0.15 g L(-1).

Evaluation on the feasibility of using bamboo fillers in plastic gear manufacturing via the Taguchi optimization method

NASA Astrophysics Data System (ADS)

Mehat, N. M.; Kamaruddin, S.

2017-10-01

An increase in demand for industrial gears has instigated the escalating uses of plastic-matrix composites, particularly carbon or glass fibre reinforced plastics as gear material to enhance the properties and limitation in plastic gears. However, the production of large quantity of these synthetic fibres reinforced composites has posed serious threat to ecosystem. Therefore, this work is conducted to study the applicability and practical ability of using bamboo fillers particularly in plastic gear manufacturing as opposed to synthetic fibres via the Taguchi optimization method. The results showed that no failure mechanism such as gear tooth root cracking and severe tooth wear were observed in gear tested made of 5-30 wt% of bamboo fillers in comparing with the unfilled PP gear. These results indicated that bamboo can be practically and economically used as an alternative filler in plastic material reinforcement as well as in minimizing the cost of raw material in general.

Structural analysis of bioceramic materials for denture application

NASA Astrophysics Data System (ADS)

Rauf, Nurlaela; Tahir, Dahlang; Arbiansyah, Muhammad

2016-03-01

Structural analysis has been performed on bioceramic materials for denture application by using X-ray diffraction (XRD), X-ray fluorescence (XRF), and Scanning Electron Microscopy (SEM). XRF is using for analysis chemical composition of raw materials. XRF shows the ratio 1 : 1 : 1 : 1 between feldspar, quartz, kaolin and eggshell, respectively, resulting composition CaO content of 56.78 %, which is similar with natural tooth. Sample preparation was carried out on temperature of 800 °C, 900 °C and 1000 °C. X-ray diffraction result showed that the structure is crystalline with trigonal crystal system for SiO2 (a=b=4.9134 Å and c=5.4051 Å) and CaH2O2 (a=b=3.5925 Å and c=4.9082 Å). Based on the Scherrer's equation showed the crystallite size of the highest peak (SiO2) increase with increasing the temperature preparation. The highest hardness value (87 kg/mm2) and match with the standards of dentin hardness. The surface structure was observed by using SEM also discussed.

Study on surface morphology and physicochemical properties of raw and activated South African coal and coal fly ash

NASA Astrophysics Data System (ADS)

Mishra, S. B.; Langwenya, S. P.; Mamba, B. B.; Balakrishnan, M.

South African coal and coal fly ash were selected as the raw materials to be used for study of their morphology and physicochemical properties and their respective activated carbons for adsorption applications. Coal and fly ash were individually steam activated at a temperature range of 550-1000 °C for 1 h in a muffle furnace using cylindrical stainless steel containers. Scanning electron micrographs revealed a change in surface morphology with more mineral matter available on the surface of the coal particles due to increased devolatilization. However, in the case of fly ash, the macerals coalesced to form agglomerates and the presence of unburnt carbon constituted pores of diameter between 50 and 100 nm. The BET surface area of coal improved significantly from 5.31 to 52.12 m 2/g whereas in case of fly ash the surface area of the raw sample which was originally 0.59 m 2/g and upon activation increased only up to 2.04 m 2/g. The chemical composition of the fly ash confirmed that silica was the major component which was approximately 60% by weight fraction. The impact of this study was to highlight the importance of using raw materials such as coal and a waste product, in the form of coal ash, in order to produce affordable activated carbon that can be used in drinking water treatment. This would therefore ensure that the quality of water supplied to communities for drinking is not contaminated especially by toxic organic compounds.

A membrane-integrated fermentation reactor system: its effects in reducing the amount of sub-raw materials for D-lactic acid continuous fermentation by Sporolactobacillus laevolacticus.

PubMed

Mimitsuka, Takashi; Na, Kyungsu; Morita, Ken; Sawai, Hideki; Minegishi, Shinichi; Henmi, Masahiro; Yamada, Katsushige; Shimizu, Sakayu; Yonehara, Tetsu

2012-01-01

Continuous fermentation by retaining cells with a membrane-integrated fermentation reactor (MFR) system was found to reduce the amount of supplied sub-raw material. If the amount of sub-raw material can be reduced, continuous fermentation with the MFR system should become a more attractive process for industrialization, due to decreased material costs and loads during the refinement process. Our findings indicate that the production rate decreased when the amount of the sub-raw material was reduced in batch fermentation, but did not decrease during continuous fermentation with Sporolactobacillus laevolacticus. Moreover, continuous fermentation with a reduced amount of sub-raw material resulted in a productivity of 11.2 g/L/h over 800 h. In addition, the index of industrial process applicability used in the MFR system increased by 6.3-fold as compared with the conventional membrane-based fermentation reactor previously reported, suggesting a potential for the industrialization of this D-lactic acid continuous fermentation process.

75 FR 67788 - Self-Regulatory Organizations; The NASDAQ Stock Market LLC; Notice of Filing of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-03

... Business Plan is to Purchase and Stockpile Raw Materials or Other Commodities In the case of a Company... stockpile quantities of a raw material or other commodity (``commodity stockpiling companies'' or ``CSCs... invest at least 85% of the net proceeds of the initial public offering in the raw material or other...

The Papers Printing Quality Complex Assessment Algorithm Development Taking into Account the Composition and Production Technological Features

NASA Astrophysics Data System (ADS)

Babakhanova, Kh A.; Varepo, L. G.; Nagornova, I. V.; Babluyk, E. B.; Kondratov, A. P.

2018-04-01

Paper is one of the printing system key components causing the high-quality printed products output. Providing the printing companies with the specified printing properties paper, while simultaneously increasing the paper products range and volume by means of the forecasting methods application and evaluation during the production process, is certainly a relevant problem. The paper presents the printing quality control algorithm taking into consideration the paper printing properties quality assessment depending on the manufacture technological features and composition variation. The information system including raw material and paper properties data and making possible pulp and paper enterprises to select paper composition optimal formulation is proposed taking into account the printing process procedure peculiarities of the paper manufacturing with specified printing properties.

Composition of 12-18 th century window glass in Belgium: Non-figurative windows in secular buildings and stained-glass windows in religious buildings

NASA Astrophysics Data System (ADS)

Schalm, Olivier; Janssens, Koen; Wouters, Hilde; Caluwé, Danielle

2007-07-01

A set of ca. 500 window glass fragments originating from different historical sites in Belgium and covering the period 12 th-18 th century was analyzed by means of electron probe microanalysis. Most samples are archaeological finds deriving from non-figurative windows in secular buildings. However, the analyzed set also contains glass sampled from still existing non-figurative windows in secular buildings and stained-glass windows in religious buildings. A sudden compositional change at the end of the 14 th century can be noticed among the series of glass compositions that were obtained. These changes could be related to the use of different glassmaker recipes and to the introduction of new raw materials for glass making.

Examination of Scanning Electron Microscope and Computed Tomography Images of PICA

NASA Technical Reports Server (NTRS)

Lawson, John W.; Stackpoole, Margaret M.; Shklover, Valery

2010-01-01

Micrographs of PICA (Phenolic Impregnated Carbon Ablator) taken using a Scanning Electron Microscope (SEM) and 3D images taken with a Computed Tomography (CT) system are examined. PICA is a carbon fiber based composite (Fiberform ) with a phenolic polymer matrix. The micrographs are taken at different surface depths and at different magnifications in a sample after arc jet testing and show different levels of oxidative removal of the charred matrix (Figs 1 though 13). CT scans, courtesy of Xradia, Inc. of Concord CA, were captured for samples of virgin PICA, charred PICA and raw Fiberform (Fig. 14). We use these images to calculate the thermal conductivity (TC) of these materials using correlation function (CF) methods. CF methods give a mathematical description of how one material is embedded in another and is thus ideally suited for modeling composites like PICA. We will evaluate how the TC of the materials changes as a function of surface depth. This work is in collaboration with ETH-Zurich, which has expertise in high temperature materials and TC modeling (including CF methods).

Synthesis of Portland cement and calcium sulfoaluminate-belite cement for sustainable development and performance

NASA Astrophysics Data System (ADS)

Chen, Irvin Allen

Portland cement concrete, the most widely used manufactured material in the world, is made primarily from water, mineral aggregates, and portland cement. The production of portland cement is energy intensive, accounting for 2% of primary energy consumption and 5% of industrial energy consumption globally. Moreover, portland cement manufacturing contributes significantly to greenhouse gases and accounts for 5% of the global CO2 emissions resulting from human activity. The primary objective of this research was to explore methods of reducing the environmental impact of cement production while maintaining or improving current performance standards. Two approaches were taken, (1) incorporation of waste materials in portland cement synthesis, and (2) optimization of an alternative environmental friendly binder, calcium sulfoaluminate-belite cement. These approaches can lead to less energy consumption, less emission of CO2, and more reuse of industrial waste materials for cement manufacturing. In the portland cement part of the research, portland cement clinkers conforming to the compositional specifications in ASTM C 150 for Type I cement were successfully synthesized from reagent-grade chemicals with 0% to 40% fly ash and 0% to 60% slag incorporation (with 10% intervals), 72.5% limestone with 27.5% fly ash, and 65% limestone with 35% slag. The synthesized portland cements had similar early-age hydration behavior to commercial portland cement. However, waste materials significantly affected cement phase formation. The C3S--C2S ratio decreased with increasing amounts of waste materials incorporated. These differences could have implications on proportioning of raw materials for cement production when using waste materials. In the calcium sulfoaluminate-belite cement part of the research, three calcium sulfoaluminate-belite cement clinkers with a range of phase compositions were successfully synthesized from reagent-grade chemicals. The synthesized calcium sulfoaluminate-belite cement that contained medium C4A3 S¯ and C2S contents showed good dimensional stability, sulfate resistance, and compressive strength development and was considered the optimum phase composition for calcium sulfoaluminate-belite cement in terms of comparable performance characteristics to portland cement. Furthermore, two calcium sulfoaluminate-belite cement clinkers were successfully synthesized from natural and waste materials such as limestone, bauxite, flue gas desulfurization sludge, Class C fly ash, and fluidized bed ash proportioned to the optimum calcium sulfoaluminate-belite cement synthesized from reagent-grade chemicals. Waste materials composed 30% and 41% of the raw ingredients. The two calcium sulfoaluminate-belite cements synthesized from natural and waste materials showed good dimensional stability, sulfate resistance, and compressive strength development, comparable to commercial portland cement.

Synthesis and electrochemical performance of cathode material Li1.2Co0.13Ni0.13Mn0.54O2 from spent lithium-ion batteries

NASA Astrophysics Data System (ADS)

Li, Li; Zhang, Xiaoxiao; Chen, Renjie; Zhao, Taolin; Lu, Jun; Wu, Feng; Amine, Khalil

2014-03-01

Li-rich layered oxide Li1.2Co0.13Ni0.13Mn0.54O2 has been successfully re-synthesized using the ascorbic acid leaching solution of spent lithium-ion batteries as the raw materials. A combination of oxalic acid co-precipitation, hydrothermal and calcination processes was applied to synthesize this material. For comparison, a fresh sample with the same composition has been also synthesized from the commercial raw materials using the same method. X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and electrochemical measurements are carried out to characterize these samples. XRD results indicate that both samples have the layered α-NaFeO2 structures with a space group of R 3 bar m. No other crystalline phase was detected by XRD. The electrochemical results show that the re-synthesized and fresh-synthesized sample can deliver discharge capacities as high as 258.8 and 264.2 mAh g-1 at the first cycle, respectively. After 50 cycles, discharge capacities of 225.1 and 228 mAh g-1 can be obtained with capacity retention of 87.0 and 86.3%, respectively. This study suggests that the leaching solution from spent lithium ion batteries can be recycled to synthesize Li-rich cathode materials with good electrochemical performance.

Novel fabrication of silicon carbide based ceramics for nuclear applications

NASA Astrophysics Data System (ADS)

Singh, Abhishek Kumar

Advances in nuclear reactor technology and the use of gas-cooled fast reactors require the development of new materials that can operate at the higher temperatures expected in these systems. These materials include refractory alloys based on Nb, Zr, Ta, Mo, W, and Re; ceramics and composites such as SiC--SiCf; carbon--carbon composites; and advanced coatings. Besides the ability to handle higher expected temperatures, effective heat transfer between reactor components is necessary for improved efficiency. Improving thermal conductivity of the fuel can lower the center-line temperature and, thereby, enhance power production capabilities and reduce the risk of premature fuel pellet failure. Crystalline silicon carbide has superior characteristics as a structural material from the viewpoint of its thermal and mechanical properties, thermal shock resistance, chemical stability, and low radioactivation. Therefore, there have been many efforts to develop SiC based composites in various forms for use in advanced energy systems. In recent years, with the development of high yield preceramic precursors, the polymer infiltration and pyrolysis (PIP) method has aroused interest for the fabrication of ceramic based materials, for various applications ranging from disc brakes to nuclear reactor fuels. The pyrolysis of preceramic polymers allow new types of ceramic materials to be processed at relatively low temperatures. The raw materials are element-organic polymers whose composition and architecture can be tailored and varied. The primary focus of this study is to use a pyrolysis based process to fabricate a host of novel silicon carbide-metal carbide or oxide composites, and to synthesize new materials based on mixed-metal silicocarbides that cannot be processed using conventional techniques. Allylhydridopolycarbosilane (AHPCS), which is an organometal polymer, was used as the precursor for silicon carbide. Inert gas pyrolysis of AHPCS produces near-stoichiometric amorphous silicon carbide (a-SiC) at 900--1150 °C. Results indicated that this processing technique can be effectively used to fabricate various silicon carbide composites with UC or UO2 as the nuclear component.

One step sintering of homogenized bauxite raw material and kinetic study

NASA Astrophysics Data System (ADS)

Gao, Chang-he; Jiang, Peng; Li, Yong; Sun, Jia-lin; Zhang, Jun-jie; Yang, Huan-ying

2016-10-01

A one-step sintering process of bauxite raw material from direct mining was completed, and the kinetics of this process was analyzed thoroughly. The results show that the sintering kinetics of bauxite raw material exhibits the liquid-phase sintering behavior. A small portion of impurities existed in the raw material act as a liquid phase. After X-ray diffraction analyses, scanning electron microscopy observations, and kinetics calculations, sintering temperature and heating duration were determined as the two major factors contributing to the sintering process and densification of bauxite ore. An elevated heating temperature and longer duration favor the densification process. The major obstacle for the densification of bauxite material is attributed to the formation of the enclosed blowhole during liquid-phase sintering.

Tracing and control of raw materials sourcing for vaccine manufacturers.

PubMed

Faretra Peysson, Laurence

2010-05-01

The control of the raw materials used to manufacture vaccines is mandatory; therefore, a very clear process must be in place to guarantee that raw materials are traced. Those who make products or supplies used in vaccine manufacture (suppliers of culture media, diagnostic tests, etc.) must apply quality systems proving that they adhere to certain standards. ISO certification, Good Manufacturing Practices for production sites and the registration of culture media with a 'Certificate of Suitability' from the European Directorate for the Quality of Medicines and Healthcare are reliable quality systems pertaining to vaccine production. Suppliers must assure that each lot of raw materials used in a product that will be used in vaccine manufacture adheres to the level of safety and traceability required. Incoming materials must be controlled in a single 'Enterprise Resource Planning' system which is used to document important information, such as the assignment of lot number, expiration date, etc. Ingredients for culture media in particular must conform to certain specifications. The specifications that need to be checked vary according to the ingredient, based on the level of risk. The way a raw material is produced is also important, and any aspect relative to cross-contamination, such as the sanitary measures used in producing and storing the raw material must be checked as well. In addition, suppliers can reduce the risk of viral contamination of raw materials by avoiding purchases in countries where a relevant outbreak is currently declared. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

Improving properties of sweet potato composite flour: Influence of lactic fermentation

NASA Astrophysics Data System (ADS)

Yuliana, Neti; Nurdjanah, Siti; Setyani, Sri; Novianti, Dini

2017-06-01

The use of locally grown crops such as sweet potato as raw material for composite flour is considered advantageous as it reduces the importation of wheat flour. However the use of native sweetpotato flour has drawback properties when applied in the food. This study was aimed to modify sweet potato flour through six methods of lactic fermentation (spontaneous, pickle brine, Lb plantarum, Lc mesentereoides, a mixed of Lb plantarum and Lc mesentereoides, and mixed of Lb plantarum, Lc mesentereoides and yeast) to increase its properties in composite flour. Composite flours were obtained after fermentation of sweet potato slices for 48h in the proportion of 50% sweet potatoes flour and 50% wheat flour. pH, moisture content, swelling power, solubility, and pasting properties were determined for the fermented and unfermented composite flours. The results indicated that the composite fermented flours had better properties than those of non fermented flour. Fermentation increased swelling power, moisture content, meanwhile, solubility, and pH, deacresed. Amylose leaching, however, was not significantly affected by the fermentation process.

Risks and reliability of manufacturing processes as related to composite materials for spacecraft structures

NASA Technical Reports Server (NTRS)

Bao, Han P.

1995-01-01

Fabricating primary aircraft and spacecraft structures using advanced composite materials entail both benefits and risks. The benefits come from much improved strength-to-weight ratios and stiffness-to-weight ratios, potential for less part count, ability to tailor properties, chemical and solvent resistance, and superior thermal properties. On the other hand, the risks involved include high material costs, lack of processing experience, expensive labor, poor reproducibility, high toxicity for some composites, and a variety of space induced risks. The purpose of this project is to generate a manufacturing database for a selected number of materials with potential for space applications, and to rely on this database to develop quantitative approaches to screen candidate materials and processes for space applications on the basis of their manufacturing risks including costs. So far, the following materials have been included in the database: epoxies, polycyanates, bismalemides, PMR-15, polyphenylene sulfides, polyetherimides, polyetheretherketone, and aluminum lithium. The first four materials are thermoset composites; the next three are thermoplastic composites, and the last one is is a metal. The emphasis of this database is on factors affecting manufacturing such as cost of raw material, handling aspects which include working life and shelf life of resins, process temperature, chemical/solvent resistance, moisture resistance, damage tolerance, toxicity, outgassing, thermal cycling, and void content, nature or type of process, associate tooling, and in-process quality assurance. Based on industry experience and published literature, a relative ranking was established for each of the factors affecting manufacturing as listed above. Potential applications of this database include the determination of a delta cost factor for specific structures with a given process plan and a general methodology to screen materials and processes for incorporation into the current conceptual design optimization of future spacecrafts as being coordinated by the Vehicle Analysis Branch where this research is being conducted.

40 CFR 428.62 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.15... material) Lead 0.0017 0.0007 English units (lb/1,000 lb of raw material) Lead 0.0017 0.0007 (c) The...

UHPC for Blast and Ballistic Protection, Explosion Testing and Composition Optimization

NASA Astrophysics Data System (ADS)

Bibora, P.; Drdlová, M.; Prachař, V.; Sviták, O.

2017-10-01

The realization of high performance concrete resistant to detonation is the aim and expected outcome of the presented project, which is oriented to development of construction materials for larger objects as protective walls and bunkers. Use of high-strength concrete (HSC / HPC - “high strength / performance concrete”) and high-fiber reinforced concrete (UHPC / UHPFC -“Ultra High Performance Fiber Reinforced Concrete”) seems to be optimal for this purpose of research. The paper describes the research phase of the project, in which we focused on the selection of specific raw materials and chemical additives, including determining the most suitable type and amount of distributed fiber reinforcement. Composition of UHPC was optimized during laboratory manufacture of test specimens to obtain the best desired physical- mechanical properties of developed high performance concretes. In connection with laboratory testing, explosion field tests of UHPC specimens were performed and explosion resistance of laboratory produced UHPC testing boards was investigated.

Synthesis of Al4SiC4 powders from kaolin grog, aluminum and carbon black by carbothermal reaction

NASA Astrophysics Data System (ADS)

Yuan, Wenjie; Yu, Chao; Deng, Chengji; Zhu, Hongxi

2013-12-01

In this paper, the synthesis of Al4SiC4 used as natural oxide materials by carbothermal reduction was investigated in order to explore the synthesis route with low costs. The samples were calcined by using kaolin grog, aluminum and carbon black as raw materials with the selected proportion at the temperature from 1500 to 1800 ° C for 2 hours under flow argon atmosphere. The phase composition of reaction products were determined by X-ray diffraction. The microstructure and elemental composition of different phases were observed and identified by scanning electron microscopy and energy dispersive spectroscopy. The mechanism of reaction processing was discussed. The results show that Al4SiC4 powders composed of hexagonal plate-like particulates with various sizes and the thickness of less than 20 μm are obtained when the temperature reaches 1800 °C.

Mining the apollo and amor asteroids.

PubMed

O'leary, B

1977-07-22

Earth-approaching asteroids could provide raw materials for space manufacturing. For certain asteroids the total energy per unit mass for the transfer of asteroidal resources to a manufacturing site in high Earth orbit is comparable to that for lunar materials. For logistical reasons the cost may be many times less. Optical studies suggest that these asteroids have compositions corresponding to those of carbonaceous and ordinary chondrites, with some containing large quantities of iron and nickel; others are thought to contain carbon, nitrogen, and hydrogen, elements that appear to be lacking on the moon. The prospect that several new candidate asteroids will be discovered over the next few years increases the likelihood that a variety of asteroidal resource materials can be retrieved on low-energy missions.

Structure and Properties of Sio2 Nanopowder Obtained From High-Silica Raw Materials by Plasma Method

NASA Astrophysics Data System (ADS)

Kosmachev, P. V.; Vlasov, V. A.; Skripnikova, N. K.

2017-06-01

The paper presents a plasma-assisted generation of nanodisperse powder obtained from diatomite, a natural high-silica material. The structure and properties of the obtained material are investigated using the transmission electron microscopy, energy dispersive X-Ray spectroscopy, infrared and X-ray photoelectron spectroscopies, and Brunauer-Emmett-Teller method. It is clearly shown that the obtained SiO2 nanoparticles are spherical, polydisperse and represented in the form of agglomerates. The specific surface of this nanopowder is 32 m2/g. Thermodynamic modeling of the plasma-assisted process is used to obtain the equilibrium compositions of condensed and gaseous reaction products. The plasma process is performed within the 300-5000 K temperature range.

Mining the Apollo and Amor asteroids

NASA Technical Reports Server (NTRS)

Oleary, B.

1977-01-01

Earth-approaching asteroids could provide raw materials for space manufacturing. For certain asteroids the total energy per unit mass for the transfer of asteroidal resources to a manufacturing site in high earth orbit is comparable to that for lunar materials. For logistical reasons the cost may be many times less. Optical studies suggest that these asteroids have compositions corresponding to those of carbonaceous and ordinary chondrites, with some containing large quantities of iron and nickel; other are thought to contain carbon, nitrogen, and hydrogen, elements that appear to be lacking on the moon. The prospect that several new candidate asteroids will be discovered over the next few years increases the likelihood that a variety of asteroidal resource materials can be retrieved on low-energy missions.

Alumosilicate ceramic proppants based on natural refractory raw materials

NASA Astrophysics Data System (ADS)

Vakalova, T. V.; Devyashina, L. P.; Burihina, M. A.; Kisner, A. S.; Pashenko, N. V.

2017-12-01

The sintering-strengthening effect of the additions of the highly ferrous bauxite (with Fe2O3 content of 20-25 % in the calcined state) in the compositions with refractory clays was established. It was found that in the temperature range 1350-1500°C the additions of bauxite in amounts of 10-40% have a fluxing effect due to the iron oxide introduced with bauxite in compositions with clay. An increasing the bauxite additive in the amount of 50-70% ensures its strengthening effect by increasing the total content of the mullite of the prismatic habit in the firing products of composites with clay. Preliminary clay and bauxite calcination at 900 °C and an increase in the content of bauxite additive up to 50-70% in compositions with clay allow to produce aluminosilicate proppants with a bulk density of 1.62-1.65 g/cm3 and compressive strength up to 52 MPa.

Fluorescence of aqueous solutions of commercial humic products

NASA Astrophysics Data System (ADS)

Gosteva, O. Yu.; Izosimov, A. A.; Patsaeva, S. V.; Yuzhakov, V. I.; Yakimenko, O. S.

2012-01-01

We have studied the spectral luminescence characteristics of aqueous solutions of humic products obtained from different raw material sources, and their behavior as the excitation wavelength increases from 270 nm to 355 nm. We have identified differences in the spectral properties of industrial humic products from coalified materials, lignin-containing organic waste, and humic products from plant raw material (peat, sapropel, vermicompost). We have shown that humic products from plant raw material have spectral properties closer to those for humic substances in natural water or soil than humic products from coalified materials.

Preliminarily comparison of nutritional composition of some fresh and processed seafood.

PubMed

Aberoumand, Ali

2012-10-01

Processing made fish less susceptible to spoilage. Fish are rich in protein content but the protein content is reduced with processing gave a better result when long-time preservation was carried out. Aim of this study was comparison of proximate analysis of some fresh and processed seafoods. Raw materials and processed seafoods (canned mackerel tuna, frozen Sea-Bream and Pressed caviar) were obtained from different firms and analyzed. Analysis carried out according AOAC methods. Moisture, protein and fat values of tuna fish were estimated to be 51, 23.9 and 21.4%, respectively. In this study, moisture content of pressed caviar was 36%, protein content was 34.4% and fat content was 16.7%, carbohydrate and energy values were 4.9% and 316 kcal/100 g, respectively. Pressed and smoked seafoods contained lower amount of moisture but higher amounts of the other components than raw materials (p < 0.05). Canned mackerel tuna, frozen sea bream and pressed caviar also contained higher amounts of fat, carbohydrate and energy, respectively (p < 0.05) than raw material. Except canning with water, all processing technologies decreased the moisture content but increased energy values (p < 0.05) of the fish. It is concluded that processed seafoods are rich in chemical components and very nutritive. Canned tuna with salted water may be advised for low-calorie diets. Caviar pressed was one the best sea foods that was produced in Iran. Since fishes are consumed as a major protein source in food, it is very important that the protein content should not be compromised during table preparation.

Quantification of main and trace metal components in the fly ash of waste-to-energy plants located in Germany and Switzerland: An overview and comparison of concentration fluctuations within and between several plants with particular focus on valuable metals.

PubMed

Haberl, Jasmin; Koralewska, Ralf; Schlumberger, Stefan; Schuster, Michael

2018-05-01

The elemental composition of fly ash from six waste-to-energy (WTE) plants in Germany and two WTE plants in Switzerland were analyzed. Samples were taken daily over a period of one month and mixed to a composite sample for each German plant. From two Swiss plants, two and three of these composite samples, respectively, were collected for different months in order to assess temporal differences between these months. In total, 61 elements, including rare earth elements, were analyzed using ICP-OES and ICP-MS. The analysis method was validated for 44 elements either by reference materials (BCR 176R and NIST 1633c) or analysis with both methods. Good recoveries, mostly ±10%, and high agreements between both methods were achieved. As long as no additives from flue gas cleaning were mixed with the fly ash, quite similar element contents were observed between all of the different incinerators. For most elements, the variations between the different months within the two Swiss plants were lower than differences between various plants. Especially main components show low variations between different months. To get a more detailed insight into temporal fluctuations within the mentioned Swiss plants, the concentrations of Zn, Pb, Cu, Cd, Sb, and Sn are presented over a period of three years (Jan. 2015 - Oct. 2017). The concentration profiles are based on weekly composite samples (consisting of daily taken samples) analyzed by the routine control of these plants using ED-XRF. The standard deviations of the average concentrations were around 20% over the three years for the regarded elements. The fluctuations were comparable at both plants. Due to the relatively low temporal concentration fluctuations observed within the plants, fly ash would be a continuous and constant source of secondary raw materials. Beside Zn, Pb, Cu, and Cd, which were already recovered on an industrial scale, Sb, Sn, and Bi also show a high potential as secondary raw material due to the high concentration of these elements in fly ash. Copyright © 2018 Elsevier Ltd. All rights reserved.

Microbiological Spoilage of Spices, Nuts, Cocoa, and Coffee

NASA Astrophysics Data System (ADS)

Pinkas, Joan M.; Battista, Karen; Morille-Hinds, Theodora

Spices, nuts, cocoa, and coffee are raw materials that may be used alone or as ingredients in the manufacture of processed food products. The control of microbiological spoilage of these raw materials at the ingredient stage will enable the food processor to better assure the production of high-quality foods with an acceptable shelf life. While this chapter is limited to four materials, many of the spoilage control procedures recommended can also be applied to other raw materials of a similar nature.

The effect of dispersion technique of montmorillonite on polyisocyanurate nanocomposites

NASA Astrophysics Data System (ADS)

Cabulis, U.; Fridrihsone, A.; Andersons, J.; Vlcek, T.

2014-05-01

The biomass represents an abundant, renewable, competitive and low cost resource that can play an alternative role to petrochemical resources. The central topic of the research activity reported is the use of rape seed oil (RO) as a raw material for the production of rigid polyisocyanurate foams (PIR). The content of the renewable resource-derived polymers achieved in ready foams is up to 20%. By using biopolymers as a matrix, a prospective way is to reinforce them with nanoparticles, organically modified clays, for improvement of mechanical properties while, at the same time, replacing petrochemical raw materials. Organoclay Cloisite® 15A was tested as a filler of PIR foams. Three different techniques - ultrasonification, mixing by three-roll mills, and high-pressure homogenization were used for dispergation of nanoclays in polyols. Composite polyisocyanurate foams and solid polymer samples were produced and tested for stiffness and strength. This paper discusses the studies into the use of RO as a renewable source in rigid PIR foams filled with organomodified montmorillonite clay with loadings from 1 to 5% by weight.

Extraction Optimization, Purification and Physicochemical Properties of Polysaccharides from Gynura medica.

PubMed

Li, Fengwei; Gao, Jian; Xue, Feng; Yu, Xiaohong; Shao, Tao

2016-03-23

Extraction of polysaccharides from Gynura medica (GMPs) was optimized by response surface methodology (RSM). A central composition design including three parameters, namely extraction temperature (X₁), ratio of water to raw material (X₂) and extraction time (X₃), was used. The best conditions were extraction temperature of 91.7 °C, extraction time of 4.06 h and ratio of water to raw material of 29.1 mL/g. Under the optimized conditions, the yield of GMPs was 5.56%, which was similar to the predicted polysaccharides yield of 5.66%. A fraction named GMP-1 was obtained after isolation and purification by DEAE-52 and Sephadex G-100 gel chromatography, respectively. GMP-1, with a molecular weight of 401 kDa, mainly consisted of galacturonic acid (GalA), xylose (Xyl), glucose (Glu). Infrared spectroscopy was used to characterize the major functional groups of GMP-1 and the results indicated that it was an acidic polysaccharide. The antioxidant and α-glucosidase inhibitory activities of GMPs and GMP-1 were determined in vitro. The results indicated that GMPs and GMP-1 show potential for use in functional foods or medicines.

Growth process and magnetic properties of α-FeSe nanostructures

NASA Astrophysics Data System (ADS)

Li, S. J.; Li, D.; Jiang, J. J.; Liu, G. B.; Ma, S.; Liu, W.; Zhang, Z. D.

2014-05-01

Growth process and magnetic properties of PbO-type α-FexSe nanostructures with shape changing from nanocacti to nanopetals and then to nanosheets are investigated. With iron acetylacetonate [Fe(acac)3] and Se powder as raw materials, the diffusion process of Fe atoms dominates the synthesis of α-FexSe nanocacti following phase transitions from FeSe2 to Fe3Se4 and finally to α-FexSe. When a mixed solution containing Se precursor and Fe(acac)3 was used as the raw material, the formation of FeSe2 and Fe3Se4 can be avoided and, bended α-FexSe nanopetals can be prepared at 345 °C, which became flat nanosheets with a [001] preferred orientation as extending the reaction time from 1 to 4 h. No superconducting transition occurs in the α-FexSe (0.84 ≤ x ≤ 1.05) nanostructures due to composition heterogeneity or size effect. Magnetic measurements indicate that an antiferromagnetic component with a Néel point at about 45 K dominates the magnetic properties of the α-Fe0.87Se nanosheets.

An economical approach for d-lactic acid production utilizing unpolished rice from aging paddy as major nutrient source.

PubMed

Lu, Zhengdong; Lu, Mingbo; He, Feng; Yu, Longjiang

2009-03-01

In order to reduce the raw material cost of d-lactic acid fermentation, the unpolished rice from aging paddy was used as major nutrient source in this study. The unpolished rice saccharificate, wheat bran powder and yeast extract were employed as carbon source, nitrogen source and growth factors, respectively. Response surface methodology (RSM) was applied to optimize the dosages of medium compositions. As a result, when the fermentation was carried out under the optimal conditions for wheat bran powder (29.10g/l) and yeast extract (2.50g/l), the d-lactic acid yield reached 731.50g/kg unpolished rice with a volumetric production rate of 1.50g/(lh). In comparison with fresh corn and polished rice, the d-lactic acid yield increased by 5.79% and 8.71%, and the raw material cost decreased by 65% and 52%, respectively, when the unpolished rice was used as a major nutrient source. These results might provide a reference for the industrial production of d-lactic acid.

Quality assessment of baby food made of different pre-processed organic raw materials under industrial processing conditions.

PubMed

Seidel, Kathrin; Kahl, Johannes; Paoletti, Flavio; Birlouez, Ines; Busscher, Nicolaas; Kretzschmar, Ursula; Särkkä-Tirkkonen, Marjo; Seljåsen, Randi; Sinesio, Fiorella; Torp, Torfinn; Baiamonte, Irene

2015-02-01

The market for processed food is rapidly growing. The industry needs methods for "processing with care" leading to high quality products in order to meet consumers' expectations. Processing influences the quality of the finished product through various factors. In carrot baby food, these are the raw material, the pre-processing and storage treatments as well as the processing conditions. In this study, a quality assessment was performed on baby food made from different pre-processed raw materials. The experiments were carried out under industrial conditions using fresh, frozen and stored organic carrots as raw material. Statistically significant differences were found for sensory attributes among the three autoclaved puree samples (e.g. overall odour F = 90.72, p < 0.001). Samples processed from frozen carrots show increased moisture content and decrease of several chemical constituents. Biocrystallization identified changes between replications of the cooking. Pre-treatment of raw material has a significant influence on the final quality of the baby food.

Rehabilitation of adobe buildings. Understanding different materials from Portugal

NASA Astrophysics Data System (ADS)

Costa, Cristiana; Rocha, Fernando; Velosa, Ana

2016-04-01

Earth construction is the oldest building material known, with documented cases of the use of earth bricks since Mesopotamia around 10 000 BC (Heathcote, 1995). The earth construction exists throughout the majority of the world in different cultures, and for some countries, nowadays it continues to be the main process of construction (Vega et al, 2011). Around 30% of the world's population lives in buildings made of earth materials. Earthen construction is an environmentally friendly technique with a social and cultural contribution; this advantage is increased when this type of construction is applied in developing countries where the material costs counterbalance with labour costs, and where other materials and techniques cannot be available (Ciancio et al, 2013). Studies of materials characterization are required in order to understand the composition and specific properties of the earth buildings, their heterogeneity and their degradation mechanisms. Some adobes from different buildings, ages and regions of Portugal were collected in order to characterize them (mineralogically, chemically and physically). It was possible to understand the composition of these materials and their differences. Main minerals are quartz, feldspars, calcite and phyllosilicates (mica and kaolinite). The mechanical behaviour of these materials isn't the best, but it is possible to improve it with some simple and cheap natural additives (kaolinitic soils). The characterization of these materials allows us to understand the differences between the materials from the different regions (controlled by locally available raw materials). Understanding these materials, and their properties, it is possible to formulate new ones for repair, conservation and rehabilitation works. The adobe bricks are an alternative of kiln baked bricks which has several advantages and one of the most important is that these materials are recyclable. Adobes are an excellent option for building rehabilitation, if composition is optimised.

Cost Models for MMC Manufacturing Processes

NASA Technical Reports Server (NTRS)

Elzey, Dana M.; Wadley, Haydn N. G.

1996-01-01

The quality cost modeling (QCM) tool is intended to be a relatively simple-to-use device for obtaining a first-order assessment of the quality-cost relationship for a given process-material combination. The QCM curve is a plot of cost versus quality (an index indicating microstructural quality), which is unique for a given process-material combination. The QCM curve indicates the tradeoff between cost and performance, thus enabling one to evaluate affordability. Additionally, the effect of changes in process design, raw materials, and process conditions on the cost-quality relationship can be evaluated. Such results might indicate the most efficient means to obtain improved quality at reduced cost by process design refinements, the implementation of sensors and models for closed loop process control, or improvement in the properties of raw materials being fed into the process. QCM also allows alternative processes for producing the same or similar material to be compared in terms of their potential for producing competitively priced, high quality material. Aside from demonstrating the usefulness of the QCM concept, this is one of the main foci of the present research program, namely to compare processes for making continuous fiber reinforced, metal matrix composites (MMC's). Two processes, low pressure plasma spray deposition and tape casting are considered for QCM development. This document consists of a detailed look at the design of the QCM approach, followed by discussion of the application of QCM to each of the selected MMC manufacturing processes along with results, comparison of processes, and finally, a summary of findings and recommendations.

Energy and raw material potentials of wood residue in the Pacific Coast States: a summary of a preliminary feasibility investigation.

Treesearch

John B. Grantham; Eldon Estep; John M. Pierovich; Harold Tarkow; Thomas C. Adams

1974-01-01

Results are reported of a preliminary investigation of feasibility of using wood residue to meet energy and raw material needs in the Pacific Coast States. Magnitude of needs was examined and volume of logging-residue and unused mill residue was estimated. Costs of obtaining and preprocessing logging residue for energy and pulp and particle board raw material were...

Perchlorate in Fertilizers

DTIC Science & Technology

1999-09-01

Harrington , showed that with respect to mixed water analysis containing TDS at greater 1,000 ppm, the performance of the AS-5 column is not as robust...to note, these raw test materials were heterogeneous. Regardless of mixing time and mesh quality, dividing the raw test materials for laboratory...raw test material was prepared and shipped to seven laboratories for blind analysis. The suspension was prepared by 4 mixing the solid sample with

[The study on fabrication of dental restoration using PMMA-ZrO2 composites via CAD/CAM].

PubMed

Li, Shi-bao; Wang, Zhong-yi; Chen, Zhao-hui; Hu, Hai-feng; Tang, Li-hui; Ma, Chu-fan

2005-01-01

To obtain dental restorations by machining PMMA-ZrO2 organic-inorganic composites with the dental CAD/CAM system. Partially sintered Zirconia compacts (PSZC) were prepared via isostatic pressing and partially sintering, with Zirconia nanopowder as raw materials. PMMA-Zirconia organic-inorganic composites were prepared by vacuum infiltrating the prepolymerized MMA into the PSZC, followed by in-situ polymerization. The mechanical properties and machinability of composites were studied. The composites were machined on the dental CAD/CAM system to obtain dental restoration. At 71.44% TD of PSZC, the composite had a 3-point bending strength of (202.56 +/- 3.09) MPa, fracture toughness of (4.30 +/- 0.16) MPa.m(1/2), elasticity modulus of (58.71 +/- 1.98) GPa, and Vickers hardness of (3.82 +/- 0.34) GPa, respectively. A premolar crown was fabricated by CAD/CAM system in 16 mins, and was verisimilitude, without any cracks. The composite at 71.44% TD of PSZC has good mechanical properties and dental restorations can be manufactured by PMMA-Zirconia composites via dental CAD/CAM system.

Dietary fish protein hydrolysates containing bioactive motifs affect serum and adipose tissue fatty acid compositions, serum lipids, postprandial glucose regulation and growth in obese Zucker fa/fa rats.

PubMed

Drotningsvik, Aslaug; Mjøs, Svein A; Pampanin, Daniela M; Slizyte, Rasa; Carvajal, Ana; Remman, Tore; Høgøy, Ingmar; Gudbrandsen, Oddrun A

2016-10-01

The world's fisheries and aquaculture industries produce vast amounts of protein-containing by-products that can be enzymatically hydrolysed to smaller peptides and possibly be used as additives to functional foods and nutraceuticals targeted for patients with obesity-related metabolic disorders. To investigate the effects of fish protein hydrolysates on markers of metabolic disorders, obese Zucker fa/fa rats consumed diets with 75 % of protein from casein/whey (CAS) and 25 % from herring (HER) or salmon (SAL) protein hydrolysate from rest raw material, or 100 % protein from CAS for 4 weeks. The fatty acid compositions were similar in the experimental diets, and none of them contained any long-chain n-3 PUFA. Ratios of lysine:arginine and methionine:glycine were lower in HER and SAL diets when compared with CAS, and taurine was detected only in fish protein hydrolysate diets. Motifs with reported hypocholesterolemic or antidiabetic activities were identified in both fish protein hydrolysates. Rats fed HER diet had lower serum HDL-cholesterol and LDL-cholesterol, and higher serum TAG, MUFA and n-3:n-6 PUFA ratio compared with CAS-fed rats. SAL rats gained more weight and had better postprandial glucose regulation compared with CAS rats. Serum lipids and fatty acids were only marginally affected by SAL, but adipose tissue contained less total SFA and more total n-3 PUFA when compared with CAS. To conclude, diets containing hydrolysed rest raw material from herring or salmon proteins may affect growth, lipid metabolism, postprandial glucose regulation and fatty acid composition in serum and adipose tissue in obese Zucker rats.

[Proximal chemical composition and functional properties of fresh meat of crab claws (Homalaspis plana)].

PubMed

Abugoch, L; Barrios, J; Guarda, A

1996-12-01

The research of alternative technological processes is being necessary in order to obtain a better utilization of hydrobiologic resources and food products, with higher added value. Crab (Homolaspis plana) is a crustacean found along the Chilean coast, whose flesh is exported as a frozen product. The resource crab is scantly studied in Chile and could became an excellent raw material for "delicatessen" products, with a high market value. The proximal composition, through the protein, fat, moisture and ashes content was determined. The non nitrogen extract was calculated by difference. The functional properties (water retention, emulsifying and gel-forming capacities) of fresh crab claws meat without additives were measured. The proximal composition for the claw meat was: 79,34 +/- 1.12% moisture, 16.75 +/- 1.29% protein, 1.86 +/- 0.11% ashes, 0.11 +/- 0.01 fat % and 1.93 +/- 1.07% N.N.E. In relation with the emulsifying capacity, claw meat was able to emulsify 2,259.03 +/- 73.04 g vegetal oil/g protein. The water retention was 154.49 +/- 6.85% representing the increase in mass percent; and the force of the gel formed in claw meat was 195.3 +/- 17.16 g-force x cm. According to these results, the claw crab is an attractive food, with a high protein and low fat content. Crab meat showed an excellent emulsifying capacity and water retention, so it can be used as a good raw material for the development of smearing products. In the case of gel-like products, further studies will be required, in order to optimize the conditions in which a stronger gel could be obtained.

Valuable natural products from marine and freshwater macroalgae obtained from supercritical fluid extracts.

PubMed

Messyasz, Beata; Michalak, Izabela; Łęska, Bogusława; Schroeder, Grzegorz; Górka, Bogusława; Korzeniowska, Karolina; Lipok, Jacek; Wieczorek, Piotr; Rój, Edward; Wilk, Radosław; Dobrzyńska-Inger, Agnieszka; Górecki, Henryk; Chojnacka, Katarzyna

2018-01-01

The biologically active compounds (fatty acids, pigments, phenolics, and flavonoid content) were studied in supercritical fluid extracts from the biomass of marine ( Ulva clathrata , Cladophora glomerata , Polysiphonia fucoides , and their multi-species mixture) and freshwater ( C. glomerata ) macroalgae. Different extraction techniques were used in order to compare differences in the biologically active compound composition of the macroalgal extracts. The results indicated that the saturated and unsaturated fatty acids ranged from C9:0 to C22:0. The analysis of differences in the composition of unsaturated to saturated fatty acids in extracts showed that palmitic acid (C16:0) and oleic acid (C18:1, n-9) reached the highest value not only in marine monospecies and multi-species biomass but also in the freshwater macroalga C. glomerata . When comparing the similarity between the concentration of fatty acids and the ratio of the concentration of unsaturated fatty acids to saturated in macroalgal extracts, we found small but not statistically significant variations in values between years (up to 10%). This is acceptable for applications as a stable raw material for industrial purposes. Significantly higher values of fatty acids, carotenoids, and chlorophylls were obtained in the case of SC-CO 2 extraction. The active ingredients of polyphenols, possessing antioxidant activity ranged from approximately 2-4%. Moreover, flavonoids represented less than 10% of the total content of polyphenolic compounds. The extraction efficiency of polyphenols was higher from a mixture of marine algae for the ultrasound-assisted extraction compared to freshwater. All these findings show that marine and freshwater macroalgae, as a raw material, have the optimal biologically active compounds composition for cosmetics.

Indonesian CPO availability analysis to support food and energy security: a system dynamic approach

NASA Astrophysics Data System (ADS)

Rahman, T.; Arkeman, Y.; Setyaningsih, D.; Saparita, R.

2017-05-01

The development of biofuels could be a solution to overcome the energy problem. One of biofuel that has the potential to be developed, namely palm oil biodiesel that is also the raw material for food. As a provider of CPO raw materials, the production of palm biodiesel could trigger competitions, from biofuels demand growth and utilization of agricultural resources. Thus, it needs to be analyzed to determine the adequency of CPO supply to fulfill the need of food and policy recomendation which sets the development of palm oil biodiesel can be synergies with food need especially for the supply of raw material CPO. To obtain the optimal policy in the synergy between the raw material of CPO for food and energy is a need to establish some policy scenarios that allow to be applied and then chosen the best policy alternative of all scenarios. The purpose of this research were to : 1) analysis the availability of CPO to meet the needs of food and energy, 2) provide policy recommendation with regard biodiesel development of food security. The model made used system dynamic method. Several scenarios that used in the model are: 1) existing condition, 2) The scenario increase biodiesel production capacity and increase land productivity, 3) reduction scenario CPO export by 30%, 4) scenario use othe raw material for biodiesel by 20%. The simulation results showed the availability of CPO raw materials would answer all needs of both food and biodiesel when there was an increase in productivity, diversification of raw materials, and also a reduction in palm oil exports. It was needed an integrated policy from upstream to downstream along with the consistency of implementation. Policy suggestions that could be considered were increased productivity through agricultural intensification, enforcement disincentive policies of CPO to exports, and development of non-CPO biodiesel raw materials and development of renewable energy.

Assembling a supercapacitor electrode with dual metal oxides and activated carbon using a liquid phase plasma.

PubMed

Ki, Seo Jin; Jeon, Ki-Joon; Park, Young-Kwon; Park, Hyunwoong; Jeong, Sangmin; Lee, Heon; Jung, Sang-Chul

2017-12-01

Developing supercapacitor electrodes at an affordable cost while improving their energy and/or power density values is still a challenging task. This study introduced a recipe which assembled a novel electrode composite using a liquid phase plasma that was applied to a reactant solution containing an activated carbon (AC) powder with dual metal precursors of iron and manganese. A comparison was made between the composites doped with single and dual metal components as well as among those synthesized under different precursor concentrations and plasma durations. The results showed that increasing the precursor concentration and plasma duration raised the content of both metal oxides in the composites, whereas the deposition conditions were more favorable to iron oxide than manganese oxide, due to its higher standard potential. The composite treated with the longest plasma duration and highest manganese concentration was superior to the others in terms of cyclic stability and equivalent series resistance. In addition, the new composite selected out of them showed better electrochemical performance than the raw AC material only and even two types of single metal-based composites, owing largely to the synergistic effect of the two metal oxides. Therefore, the proposed methodology can be used to modify existing and future composite electrodes to improve their performance with relatively cheap host and guest materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synthesis and characterization of methyltrihydroxysilane water repellent

NASA Astrophysics Data System (ADS)

Abidin, A. Z.; Harjandi, M. N.; Wirawan, V.; Suharno, S. M.

2018-03-01

Methyltrihydroxysilane (CH3Si (OH)3) as a water repellent has been synthesized from trichloromethylsilane and ethanol by varying their composition, reaction condition, and the addition of nanosilica. The properties of the material have been characterized using FTIR for identification of raw materials and water repellent product, SEM for identification of water repellent coating surface, and tensiometer for measurement of water repellent contact angle. The FTIR spectra confirm the reaction of the water-repellent formation. The water repellent product was applied by spraying or dip coating on the automotive window surface. This study shows that the best ethanol composition is 91% and the best contact angle of synthesized water repellent material is 149,46°. This contact angle is higher than that of a commercial product, which shows it as a property of the superhydrophobic material. Water repellency properties increase as the composition of trichloromethylsilane increases. It shows that the increasing of trichloromethylsilane composition can also increase methyltrihydroxysilane formation. However, glass surface becomes opaque as the composition of trichloromethylsilane increase because methyltrihydroxysilane will create the Si-O-Si layer that has a white color. The addition of nanomaterial also increases the surface roughness, but a binder is required to bind nanomaterial to the water-repellent layer. For an application, dip coating has better water repellency than spraying. This is because dip coating method creates more homogenous nanomaterial precipitation on the surface. On the other hand, the level of transparency is worse. Therefore, the water repellent of trichloromethylsilane is recommended for applications that do not need clarity such bathroom glass wall.

High voltage fragmentation of composites from secondary raw materials - Potential and limitations.

PubMed

Leißner, T; Hamann, D; Wuschke, L; Jäckel, H-G; Peuker, U A

2018-04-01

The comminution of composites for liberation of valuable components is a costly and energy-intensive process within the recycling of spent products. It therefore is continuously studied and optimized. In addition to conventional mechanical comminution innovative new principles for size reduction have been developed. One is the use of high voltage (HV) pulses, which is known to be a technology selectively liberating along phase boundaries. This technology offers the advantage of targeted liberation, preventing overgrinding of the material and thus improving the overall processing as well as product quality. In this study, the high voltage fragmentation of three different non-brittle composites (galvanized plastics, carbon fibre composites, electrode foils from Li-ion batteries) was investigated. The influence of pulse rate, number of pulses and filling level on the liberation and efficiency of comminution is discussed. Using the guideline VDI 2225 HV, fragmentation is compared to conventional mechanical comminution with respect to numerous criteria such as cost, throughput, energy consumption, availability and scalability. It was found that at current state of development, HV fragmentation cannot compete with mechanical comminution beyond laboratory scale. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chemical and biological comparison of raw and vinegar-baked Radix Bupleuri.

PubMed

Li, Zhen-Yu; Sun, Hui-Min; Xing, Jie; Qin, Xue-Mei; Du, Guan-Hua

2015-05-13

Radix Bupleuri (RB) is a commonly used herbal drug in Traditional Chinese Medicine (TCM), and it can be baked with vinegar to afford vinegar-baked Radix Bupleuri (VBRB), which is used in TCM for liver diseases treatment. In this study, the chemical compositions and biological effects between raw and two processed RBs by different vinegars were systematically compared. The chemical compositions of raw and two processed RBs were analyzed by (1)H NMR spectroscopy coupled with multivariate analysis. Two different extraction procedures were used, including direct extraction and liquid-liquid partition. Then HPLC was applied to determine the changes of saikosaponin contents. In addition, their liver protective effects against CCl4 induced liver injury were also investigated, and the biochemical parameters and histopathology were measured after treatment of mice with raw RB and two processed RBs (5 g/kg/day) for 14 days. Multivariate analysis showed clear differences between the raw and the two processed RBs, and the vinegar-baking process induced elevated contents of ssb1, ssb2, acetic acid, malic acid, citric acid, 5-HMF, and ligustrazine, as well as the decreased contents of ssa, ssd, sucrose, glycine, succinic acid etc. In addition, both raw and processed RBs showed liver protective effects against CCl4 induced liver injury, and the vinegar-baked RBs showed better effects than that of raw RB. The raw and vinegar-baked RBs differed not only in the chemical compositions but also in the pharmacological effects. And two processed RBs also showed chemical differences, suggesting that the type of vinegar had an important effect on vinegar baking. In order to ensure the therapeutic effect and safety of TCM, the effect of different vinegars on processing of herbal drugs should be further studied. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

77 FR 31388 - Importer of Controlled Substances; Notice of Application; Noramco, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

... material are not appropriate. 72 FR 3417 (2007). In regard to the non-narcotic raw material, any bulk... following basic classes of controlled substances: Drug Schedule Phenylacetone (8501) II Opium, raw (9600) II Poppy Straw Concentrate (9670) II Tapentadol (9780) II The company plans to import the raw Opium (9600...

40 CFR 428.105 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5... daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Chromium 0...

40 CFR 428.105 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 2.0 0.73 BOD5 3.72 2.20 TSS 6.96 2.90 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 2.0 0.73 BOD5... daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material) Chromium 0...

Evaluation of four raw meat diets using domestic cats, captive exotic felids, and cecectomized roosters.

PubMed

Kerr, K R; Beloshapka, A N; Morris, C L; Parsons, C M; Burke, S L; Utterback, P L; Swanson, K S

2013-01-01

Our objective was to evaluate raw meat diets for captive exotic and domestic carnivores containing traditional and alternative raw meat sources, specifically, beef trimmings, bison trimmings, elk muscle meat, and horse trimmings. We aimed to examine diet composition and protein quality; apparent total tract energy and macronutrient digestibility in domestic cats, African wildcats, jaguars, and Malayan tigers; and ME and fecal fermentative end-products in domestic cats. Because of variation in the meat sources, dietary proximate, AA, and long-chain fatty acid composition were variable. Our analyses indicated that all diets had essential fatty acid deficiencies, and the elk diet (i.e., trimmed muscle meat) was deficient in total fat. Standardized AA digestibilities measured using the cecectomized rooster assay were high (>87%). Using the NRC minimum requirements for the growth of kittens, the first limiting AA of all diets was the combined requirement of Met and Cys (AA score: 81 to 95; protein digestibility corrected AA score: 75 to 90). All diets were highly digestible (88 to 89% OM digestibility). There was no effect of diet or felid species on DM (85 to 87%), OM, and GE (90 to 91%) digestibilities. Apparent CP digestibility was greater (P≤0.05) in cats fed elk (97%) compared with those fed bison (96%), and greater (P≤0.05) in wildcats (97%) and domestic cats (97%) compared with tigers (95%). The diet and species interaction (P≤0.05) was observed for apparent fat digestibility. In domestic cats, the fresh fecal pH and proportions of acetate and butyrate were altered (P≤0.05) due to diet. Diet also affected (P≤0.05) fresh fecal concentrations of total branched-chain fatty acids, valerate, and Lactobacillus genus. In conclusion, although the raw meat diets were highly digestible, because of variation in raw meat sources the nutrient composition of the diets was variable. Thus, compositional analysis of raw meat sources is necessary for proper diet formulation. The types of meat commonly used in raw meat diets may be deficient in total fat (trimmed muscle meat) and essential fatty acids (trimmings and muscle meats). Additionally, differences in raw meat source nutrient composition and digestibility affect the beneficial and putrefactive fermentative end-products found in feces.

Characterization of Thallium Bromide Detectors Made From Material Purified by the Filter Method

NASA Astrophysics Data System (ADS)

Onodera, Toshiyuki; Hitomi, Keitaro; Tada, Tsutomu; Shoji, Tadayoshi; Mochizuki, Katsumi

2013-10-01

Thallium bromide (TlBr) has been regarded as candidate detector materials for the gamma-ray spectrometers operating at room temperature. In this study, a simple and rapid method, the filter method, was performed to purify a raw TlBr material used for fabrication of TlBr detectors. The material was loaded on shards of crashed quartz and installed in a Pyrex tube, and was melted using a furnace. A purified material passing through interspaces of the shards of quartz was collected in a quartz ampoule located at the outlet of the Pyrex tube. After the purification, impurities colored black extracted from the raw material remained. TlBr crystals were then grown by the travelling molten zone method both from the raw material and the purified material. TlBr detectors were fabricated from the grown crystals, and were characterized by measuring mobility-lifetime products (μτ) for carriers and gamma-ray spectra ( 137Cs) at room temperature. μτ for electrons of a TlBr detector fabricated from the purified material was around 5 times higher than that of a detector fabricated from the raw material.

Preparation and characterization of highly transparent Nd:YAG/YAG composite ceramics

NASA Astrophysics Data System (ADS)

Ma, Benyuan; Zhang, Wei; Shen, Bizhou; Wang, Yuezhong; Song, Haizhi; Li, Feng; Xie, Xiumin; Zhang, Zhibin; Yang, Yongqiang; Guan, Zhouguo

2018-05-01

Using the co-precipitated Nd:YAG and YAG powders as raw materials, the Nd:YAG/YAG composite ceramics (Ф 50 mm × 5 mm) were prepared by vacuum sintering (1790 °C 50 h), followed by hot isostatic pressing (HIP) post treatment (1700 °C 2 h, 200 MPa Ar atmosphere) and air annealing (1250 °C 100 h). The optical properties of Nd:YAG/YAG samples were improved markedly by HIP post-treatment, mainly due to the elimination of residual pores in the samples. The composite sample showed a perfect bonding interface from Nd:YAG to YAG regions without obvious grain size difference, pores or other defects. This structure should be responsible for the thermal conductivity larger than that of non-composite sample. The composite sample revealed good optical properties with transmittance up to 83.9% at 1064 nm and 80.8% at 400 nm, and a maximum laser output power of 1.38 KW with the slope efficiency of 36.7% was obtained.

Lipid composition analysis of milk fats from different mammalian species: potential for use as human milk fat substitutes.

PubMed

Zou, Xiaoqiang; Huang, Jianhua; Jin, Qingzhe; Guo, Zheng; Liu, Yuanfa; Cheong, Lingzhi; Xu, Xuebing; Wang, Xingguo

2013-07-24

The lipid compositions of commercial milks from cow, buffalo, donkey, sheep, and camel were compared with that of human milk fat (HMF) based on total and sn-2 fatty acid, triacylglycerol (TAG), phospholipid, and phospholipid fatty acid compositions and melting and crystallization profiles, and their degrees of similarity were digitized and differentiated by an evaluation model. The results showed that these milk fats had high degrees of similarity to HMF in total fatty acid composition. However, the degrees of similarity in other chemical aspects were low, indicating that these milk fats did not meet the requirements of human milk fat substitutes (HMFSs). However, an economically feasible solution to make these milks useful as raw materials for infant formula production could be to modify these fats, and a possible method is blending of polyunsaturated fatty acids (PUFA) and 1,3-dioleoyl-2-palmitoylglycerol (OPO) enriched fats and minor lipids based on the corresponding chemical compositions of HMF.

Determination of Proximate, Minerals, Vitamin and Anti-Nutrients Composition of Solanum verbascifolium Linn.

NASA Astrophysics Data System (ADS)

Sam, S. M.; Udosen, I. R.; Mensah, S. I.

2012-07-01

The proximate, minerals, vitamins and anti-nutrients composition of Solanum verbascifolium Linn were determined. The proximate composition showed that moisture content was (85.5%), protein was (32.55%), lipid was (2.90%), ash was (7.20%), fibre was (4.80%), carbohydrate was (52.55%) and caloric value was (366.50%) respectively. This was found to be rich in protein and considerably high amount of carbohydrate. The anti-nutrient composition analysis revealed the presence of hydrocyanide (1.39mg/100g), Oxalate (114.40mg/100g), all of which are below toxic level except for oxalic acid. For mineral and vitamin compositions, potassium was significantly (P>0.05) higher than iron, sodium, calcium and phosphorus while vitamin A retinol was (371.72mg/100g) and vitamin C ascorbic acid (39.99mg/100g). Based on these findings the plant is recommended for consumption and for further investigation as a potential raw material for pharmaceutical industry.

Synthesis and Characterization of Zr-BASED Amorphous and Crystalline Composite Coating on Ti Substrate by Laser Cladding

NASA Astrophysics Data System (ADS)

Tang, D. M.; Zhang, D. C.; Peng, W.; Luo, Z. C.; Wu, X. Q.; Wang, Y. M.; Lin, J. G.

2014-02-01

A thin strip of a Zr-based alloy with a composition of Zr60Cu25Fe5Al10 (in atom percent) was used as a raw material, and the composite coatings containing Zr-based amorphous phase and crystallites on Ti substrate were fabricated by a one-step laser cladding method without protection. The microstructure, phase constitution, microhardness and wear properties of the coatings were investigated. The results indicate that the microstructure of the coatings is strongly dependent on the laser scanning speed under the conditions of the laser power of 1300 W and laser beam diameter of 6 mm, and the composite coating mainly containing amorphous phase with a small amount of the crystallites can be obtained at the laser scanning speed of 10 mm/s. The composite coating exhibits much higher microhardness than the pure Ti substrate, and thus it behaves superior wear resistance in comparison with the substrate.

Preparation and characterization of copper-graphite composites by electrical explosion of wire in liquid.

PubMed

Bien, T N; Gul, W H; Bac, L H; Kim, J C

2014-11-01

Copper-graphite nanocomposites containing 5 vol.% graphite were prepared by a powder metallurgy route using an electrical wire explosion (EEW) in liquid method and spark plasma sintering (SPS) process. Graphite rods with a 0.3 mm diameter and copper wire with a 0.2 mm diameter were used as raw materials for EEWin liquid. To compare, a pure copper and copper-graphite mixture was also prepared. The fabricated graphite was in the form of a nanosheet, onto which copper particles were coated. Sintering was performed at 900 degrees C at a heating rate of 30 degrees C/min for 10 min and under a pressure of 70 MPa. The density of the sintered composite samples was measured by the Archimedes method. A wear test was performed by a ball-on-disc tribometer under dry conditions at room temperature in air. The presence of graphite effectively reduced the wear of composites. The copper-graphite nanocomposites prepared by EEW had lower wear rates than pure copper material and simple mixed copper-graphite.

Mathematical model of silicon smelting process basing on pelletized charge from technogenic raw materials

NASA Astrophysics Data System (ADS)

Nemchinova, N. V.; Tyutrin, A. A.; Salov, V. M.

2018-03-01

The silicon production process in the electric arc reduction furnaces (EAF) is studied using pelletized charge as an additive to the standard on the basis of the generated mathematical model. The results obtained due to the model will contribute to the analysis of the charge components behavior during melting with the achievement of optimum final parameters of the silicon production process. The authors proposed using technogenic waste as a raw material for the silicon production in a pelletized form using liquid glass and aluminum production dust from the electrostatic precipitators as a binder. The method of mathematical modeling with the help of the ‘Selector’ software package was used as a basis for the theoretical study. A model was simulated with the imitation of four furnace temperature zones and a crystalline silicon phase (25 °C). The main advantage of the created model is the ability to analyze the behavior of all burden materials (including pelletized charge) in the carbothermic process. The behavior analysis is based on the thermodynamic probability data of the burden materials interactions in the carbothermic process. The model accounts for 17 elements entering the furnace with raw materials, electrodes and air. The silicon melt, obtained by the modeling, contained 91.73 % wt. of the target product. The simulation results showed that in the use of the proposed combined charge, the recovery of silicon reached 69.248 %, which is in good agreement with practical data. The results of the crystalline silicon chemical composition modeling are compared with the real silicon samples of chemical analysis data, which showed the results of convergence. The efficiency of the mathematical modeling methods in the studying of the carbothermal silicon obtaining process with complex interphase transformations and the formation of numerous intermediate compounds using a pelletized charge as an additive to the traditional one is shown.

Investigation of Magnetic Properties and Mechanical Responses on Hydrogel-TMAH-Magnetite

NASA Astrophysics Data System (ADS)

Sunaryono; Hidayat, M. F.; Insjaf, C.; Taufiq, A.; Mufti, N.; Munasir

2018-05-01

Hydrogel-TMAH-Magnetite (ferrogel) was fabricated by using polyvinyl alcohol (PVA) hydrogel and magnetite fluids with tetramethylammonium hydroxide (TMAH) surfactant. Iron sand as the raw material was used to synthesize magnetite nanoparticles by co-precipitation method. Magnetite nanoparticles and ferrogel were characterized using X-Ray Fluorescence (XRF) to determine the content of elements in it. To know the functional group network of magnetite nanoparticles, magnetite enclosed with TMAH and ferrogel; we investigated using Fourier Transform Infra-Red (FTIR). Meanwhile, the magnetic properties of the hydrogel-TMAH-magnetite were measured by using Vibrating Sample Magnetometer (VSM). Furthermore, the composition analysis of the ferrogels using FTIR showed that all the synthesis materials were inside the ferrogels. The saturation magnetization of the hydrogel-TMAH-magnetite with a composition of TMAH 1.2 mL (3.95 emu·g-1) was higher than that of TMAH 0.8 mL (0.85 emu·g-1). It exhibited that the composition of TMAH 1.2 mL was an optimum composition to produce nanoparticle magnetite-TMAH having a stable and high performance. Furthermore, the magneto-elasticity of hydrogel-TMAH-magnetite in the effect of the external magnetic field had a good response. However, the composition of the nanoparticle magnetite-TMAH in the ferrogel did not significantly affect the elongation of the gel.

Pore structure modified diatomite-supported PEG composites for thermal energy storage

NASA Astrophysics Data System (ADS)

Qian, Tingting; Li, Jinhong; Deng, Yong

2016-09-01

A series of novel composite phase change materials (PCMs) were tailored by blending PEG and five kinds of diatomite via a vacuum impregnation method. To enlarge its pore size and specific surface area, different modification approaches including calcination, acid treatment, alkali leaching and nano-silica decoration on the microstructure of diatomite were outlined. Among them, 8 min of 5 wt% NaOH dissolution at 70 °C has been proven to be the most effective and facile. While PEG melted during phase transformation, the maximum load of PEG could reach 70 wt.%, which was 46% higher than that of the raw diatomite. The apparent activation energy of PEG in the composite was 1031.85 kJ·mol-1, which was twice higher than that of the pristine PEG. Moreover, using the nano-silica decorated diatomite as carrier, the maximum PEG load was 66 wt%. The composite PCM was stable in terms of thermal and chemical manners even after 200 cycles of melting and freezing. All results indicated that the obtained composite PCMs were promising candidate materials for building applications due to its large latent heat, suitable phase change temperature, excellent chemical compatibility, improved supercooling extent, high thermal stability and long-term reliability.

Pore structure modified diatomite-supported PEG composites for thermal energy storage

PubMed Central

Qian, Tingting; Li, Jinhong; Deng, Yong

2016-01-01

A series of novel composite phase change materials (PCMs) were tailored by blending PEG and five kinds of diatomite via a vacuum impregnation method. To enlarge its pore size and specific surface area, different modification approaches including calcination, acid treatment, alkali leaching and nano-silica decoration on the microstructure of diatomite were outlined. Among them, 8 min of 5 wt% NaOH dissolution at 70 °C has been proven to be the most effective and facile. While PEG melted during phase transformation, the maximum load of PEG could reach 70 wt.%, which was 46% higher than that of the raw diatomite. The apparent activation energy of PEG in the composite was 1031.85 kJ·mol−1, which was twice higher than that of the pristine PEG. Moreover, using the nano-silica decorated diatomite as carrier, the maximum PEG load was 66 wt%. The composite PCM was stable in terms of thermal and chemical manners even after 200 cycles of melting and freezing. All results indicated that the obtained composite PCMs were promising candidate materials for building applications due to its large latent heat, suitable phase change temperature, excellent chemical compatibility, improved supercooling extent, high thermal stability and long-term reliability. PMID:27580677

Pore structure modified diatomite-supported PEG composites for thermal energy storage.

PubMed

Qian, Tingting; Li, Jinhong; Deng, Yong

2016-09-01

A series of novel composite phase change materials (PCMs) were tailored by blending PEG and five kinds of diatomite via a vacuum impregnation method. To enlarge its pore size and specific surface area, different modification approaches including calcination, acid treatment, alkali leaching and nano-silica decoration on the microstructure of diatomite were outlined. Among them, 8 min of 5 wt% NaOH dissolution at 70 °C has been proven to be the most effective and facile. While PEG melted during phase transformation, the maximum load of PEG could reach 70 wt.%, which was 46% higher than that of the raw diatomite. The apparent activation energy of PEG in the composite was 1031.85 kJ·mol(-1), which was twice higher than that of the pristine PEG. Moreover, using the nano-silica decorated diatomite as carrier, the maximum PEG load was 66 wt%. The composite PCM was stable in terms of thermal and chemical manners even after 200 cycles of melting and freezing. All results indicated that the obtained composite PCMs were promising candidate materials for building applications due to its large latent heat, suitable phase change temperature, excellent chemical compatibility, improved supercooling extent, high thermal stability and long-term reliability.

Ethanol Production from Traditional and Emerging Raw Materials

NASA Astrophysics Data System (ADS)

Rudolf, Andreas; Karhumaa, Kaisa; Hahn-Hägerdal, Bärbel

The ethanol industry of today utilizes raw materials rich in saccharides, such as sugar cane or sugar beets, and raw materials rich in starch, such as corn and wheat. The concern about supply of liquid transportation fuels, which has brought the crude oil price above 100 /barrel during 2006, together with the concern about global warming, have turned the interest towards large-scale ethanol production from lignocellulosic materials, such as agriculture and forestry residues. Baker's yeast Saccharomyces cerevisiae is the preferred fermenting microorganism for ethanol production because of its superior and well-documented industrial performance. Extensive work has been made to genetically improve S. cerevisiae to enable fermentation of lignocellulosic raw materials. Ethanolic fermentation processes are conducted in batch, fed-batch, or continuous mode, with or without cell recycling, the relative merit of which will be discussed.

Natural stone muds as secondary raw materials: towards a new sustainable recovery process

NASA Astrophysics Data System (ADS)

Zichella, Lorena; Tori, Alice; Bellopede, Rossana; Marini, Paola

2016-04-01

The production of residual sludge is a topical issue, and has become essential to recover and reuse the materials, both for the economics and the environmental aspect. According to environmental EU Directives, in fact ,the stone cutting and processing should characterized by following objectives, targets and actions: the reduction of waste generated, the decreasing of use of critical raw material, the zero landfilling of sludge and decreasing in potential soil contamination, the prevention of transport of dangerous waste, the reduction of energy consumption, the zero impact on air pollution and the cost reduction . There are many industrial sector in which residual sludge have high concentrations of metals and/or elements deemed harmful and therefore hazardous waste. An important goal, for all industrial sectors, is an increase in productivity and a parallel reduction in costs. The research leads to the development of solutions with an always reduced environmental impact. The possibility to decrease the amount of required raw materials and at the same time the reduction in the amount of waste has become the aim for any industrial reality. From literature there are different approaches for the recovery of raw and secondary materials, and are often used for the purpose chemical products that separate the elements constituting the mud but at the same time make additional pollutants. The aim of the study is to find solutions that are environmentally sustainable for both industries and citizens. The present study is focused on three different Piedmont rocks: Luserna, Diorite from Traversella and Diorite from Vico, processed with three different stone machining technologies: cutting with diamond wire in quarry (blocks), in sawmill (slabs) and surface polishing. The steps are: chemical analysis, particle size analysis and mineralogical composition and characterization of the sludge obtained from the various machining operations for the recovery of the metal material by cutting and waste rock through an economical and simple method, without the use of chemical products. The technical feasibility of the use of stone mud for construction materials, and industrial mud for alloy reuse, is well known on a scientific and lab scale, but it is not industrially developed because of the wide variety of waste generated and logistic or organization difficulties of interaction among companies of different sectors. This can be realized implementing an existing plant with industrial technologies in order to valorize the product "mud", to reuse the heavy metals in the process and therefore to minimize the volume of sludge produced. A further progress to the previous researches, that is beyond the results obtained in this field, will be the identification of the best technique to eliminate the small amount of heavy metals in the mud fines. This is important because , removing all the toxic substances, the mud properties can be improved in order to be reuse in the other process as secondary raw material.

Liquid oil and residual characteristics of printed circuit board recycle by pyrolysis.

PubMed

Lin, Kuo-Hsiung; Chiang, Hung-Lung

2014-04-30

Non-metal fractions of waste printed circuit boards (PCBs) were thermally treated (200-500°C) under nitrogen atmosphere. Carbon, hydrogen, and nitrogen were determined by elemental analyzer, bromine by instrumental neutron activation analysis (INAA), phosphorus by energy dispersive X-ray spectrometer (EDX), and 29 trace elements by inductively coupled plasma atomic emission spectrometer (ICP-AES) and mass spectrometry (ICP-MS) for raw material and pyrolysis residues. Organic compositions of liquid oil were identified by GC (gas chromatography)-MS, trace element composition by ICP system, and 12 water-soluble ions by IC (ionic chromatography). Elemental content of carbon was >450 mg/g, oxygen 300 mg/g, bromine and hydrogen 60 mg/g, nitrogen 30 mg/g, and phosphorus 28 mg/g. Sulfur was trace in PCBs. Copper content was 25-28 mg/g, iron 1.3-1.7 mg/g, tin 0.8-1.0mg/g and magnesium 0.4-1.0mg/g; those were the main metals in the raw materials and pyrolytic residues. In the liquid products, carbon content was 68-73%, hydrogen was 10-14%, nitrogen was 4-5%, and sulfur was less than 0.05% at pyrolysis temperatures from 300 to 500°C. Phenol, 3-bromophenol, 2-methylphenol and 4-propan-2-ylphenol were major species in liquid products, accounting for >50% of analyzed organic species. Bromides, ammonium and phosphate were the main species in water sorption samples for PCB pyrolysis exhaust. Copyright © 2014 Elsevier B.V. All rights reserved.

Not Just Lumber—Using Wood in the Sustainable Future of Materials, Chemicals, and Fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jakes, Joseph E.; Arzola, Xavier; Bergman, Rick

Forest-derived biomaterials can play an integral role in a sustainable and renewable future. Research across a range of disciplines is required to develop the knowledge necessary to overcome the challenges of incorporating more renewable forest resources in materials, chemicals, and fuels. We focus on wood specifically because in our view, better characterization of wood as a raw material and as a feedstock will lead to its increased utilization. We first give an overview of wood structure and chemical composition and then highlight current topics in forest products research, including (1) industrial chemicals, biofuels, and energy from woody materials; (2) wood-basedmore » activated carbon and carbon nanostructures; (3) development of improved wood protection treatments; (4) massive timber construction; (5) wood as a bioinspiring material; and (6) atomic simulations of wood polymers. We conclude with a discussion of the sustainability of wood as a renewable forest resource.« less

Not Just Lumber—Using Wood in the Sustainable Future of Materials, Chemicals, and Fuels

NASA Astrophysics Data System (ADS)

Jakes, Joseph E.; Arzola, Xavier; Bergman, Rick; Ciesielski, Peter; Hunt, Christopher G.; Rahbar, Nima; Tshabalala, Mandla; Wiedenhoeft, Alex C.; Zelinka, Samuel L.

2016-09-01

Forest-derived biomaterials can play an integral role in a sustainable and renewable future. Research across a range of disciplines is required to develop the knowledge necessary to overcome the challenges of incorporating more renewable forest resources in materials, chemicals, and fuels. We focus on wood specifically because in our view, better characterization of wood as a raw material and as a feedstock will lead to its increased utilization. We first give an overview of wood structure and chemical composition and then highlight current topics in forest products research, including (1) industrial chemicals, biofuels, and energy from woody materials; (2) wood-based activated carbon and carbon nanostructures; (3) development of improved wood protection treatments; (4) massive timber construction; (5) wood as a bioinspiring material; and (6) atomic simulations of wood polymers. We conclude with a discussion of the sustainability of wood as a renewable forest resource.

The investigation of solid slag obtained by neutralization of sewage sludge.

PubMed

Kavaliauskas, Zydrunas; Valincius, Vitas; Stravinskas, Giedrius; Milieska, Mindaugas; Striugas, Nerijus

2015-11-01

The purpose of this research is to investigate the feasibility of utilizing the slag collected after gasification of organic fuel combined with sewage sludge. The residue left after gasification process is likely usable as raw material for production of supercondensers. The sewage sludge neutralization system consists of a dosing system (fuel tank), gasifier, plasma reactor, electrostatic filter, and heat exchangers. For the gasification process, dried solid sewage is supplied in proportion of 70% to biomass 30% by weight. The slag is collected in a specially designed chamber beneath the gasifier. A scanning electron microscope (SEM) was used to evaluate surface morphology of the samples. Elemental analysis of the sewage sludge slag was performed using the energy-dispersive spectroscopy (EDS) method, which showed different solid-state elements contained in the porous structure of the solid phase: carbon 29%, aluminum 26%, potassium 20%, chlorine 1%, and others. The specific surface area of the sewage sludge slag is 6.15 m(2)/g as the BET analysis shows. In order to use the slag as a secondary raw material, detailed analysis of the structure and properties is necessary for a decision on whether the slag left after gasification of sewage sludge is suitable for any further usages. Initial results indicate that the slag may be used for production of electrodes for supercapacitors. Every year thousands of tons of sewage sludge are formed in Lithuania. Sewage sludge consists of organic and inorganic compounds. Partial combustion, plasma decomposition, and other methods are used to neutralize the sewage sludge. The incineration of sewage sludge results in generation of solid-phase slag. In this paper the material structure and composition of a solid slag (formed during neutralization of sewage sludge) is considered. Also, the impact the ambient temperature on structure and composition of solid slag is analyzed.

Hydrogenated cottonseed oil as raw material for biobased materials

USDA-ARS?s Scientific Manuscript database

There has been a lot of recent interest in using vegetable oils as biodegradable and renewable raw materials for the syntheses of various biobased materials. Although most of the attention has been paid to soybean oil thus far, cottonseed oil is a viable alternative. An advantage of cottonseed oil...

40 CFR 428.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.63 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.53 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.70 0.25 TSS 1.28 0.64 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.26 0.093 TSS 0.50 0.25 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

40 CFR 428.63 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... consecutive days shall not exceed— Metric units (kg/kkg of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH (1) (1) English units (lb/1,000 lb of raw material) Oil and grease 0.42 0.15 TSS 0.80 0.40 pH... Average of daily values for 30 consecutive days shall not exceed— Metric units (kg/kkg of raw material...

Applications of additive manufacturing in dentistry: A review.

PubMed

Bhargav, Aishwarya; Sanjairaj, Vijayavenkatraman; Rosa, Vinicius; Feng, Lu Wen; Fuh Yh, Jerry

2017-07-24

Additive manufacturing (AM) or 3D printing has been hailed as the third industrial revolution as it has caused a paradigm shift in the way objects have been manufactured. Conventionally, converting a raw material to a fully finished and assembled, usable product comprises several steps which can be eliminated by using this process as functional products can be created directly from the raw material at a fraction of the time originally consumed. Thus, AM has found applications in several sectors including automotive, aerospace, printed electronics, and healthcare. AM is increasingly being used in the healthcare sector, given its potential to fabricate patient-specific customized implants with required accuracy and precision. Implantable heart valves, rib cages, and bones are some of the examples where AM technologies are used. A vast variety of materials including ceramics, metals, polymers, and composites have been processed to fabricate intricate implants using 3D printing. The applications of AM in dentistry include maxillofacial implants, dentures, and other prosthetic aids. It may also be used in surgical training and planning, as anatomical models can be created at ease using AM. This article gives an overview of the AM process and reviews in detail the applications of 3D printing in dentistry. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2017. © 2017 Wiley Periodicals, Inc.

Total Flavonoids Content in the Raw Material and Aqueous Extractives from Bauhinia monandra Kurz (Caesalpiniaceae)

PubMed Central

Fernandes, Ana Josane Dantas; Ferreira, Magda Rhayanny Assunção; Randau, Karina Perrelli; de Souza, Tatiane Pereira; Soares, Luiz Alberto Lira

2012-01-01

The aim of this work was to evaluate the spectrophotometric methodology for determining the total flavonoid content (TFC) in herbal drug and derived products from Bauhinia monandra Kurz. Several analytical parameters from this method grounded on the complex formed between flavonoids and AlCl3 were evaluated such as herbal amount (0.25 to 1.25 g); solvent composition (ethanol 40 to 80%, v/v); as well as the reaction time and AlCl3 concentration (2 to 9%, w/v). The method was adjusted to aqueous extractives and its performance studied through precision, linearity and preliminary robustness. The results showed an important dependence of the method response from reaction time, AlCl3 concentration, sample amount, and solvent mixture. After choosing the optimized condition, the method was applied for the matrixes (herbal material and extractives), showing precision lower than 5% (for both parameters repeatability and intermediate precision), coefficient of determination higher than 0.99, and no important influence could be observed for slight variations from wavelength or AlCl3 concentration. Thus, it could be concluded that the evaluated analytical procedure was suitable to quantify the total flavonoid content in raw material and aqueous extractives from leaves of B. monandra. PMID:22701375

Corrosion Resistance of Stainless Steels in Biodiesel

NASA Astrophysics Data System (ADS)

Román, Alejandra S.; Méndez, Claudia M.; Ares, Alicia E.

The aim of this work was to study the corrosion behavior of stainless steels in biodiesel of vegetal origin, at room temperature, evaluating its properties according to the differences in the structures (austenitic, ferritic and austenitic — ferritic) and compositions of the materials. The biodiesel employed was obtained by industrially manufactured based on soybean oil as main raw material. The stainless steels used as samples for the tests were: AISI 304L, Sea Cure and Duplex 2205. For obtaining the desired data potentiodynamic polarization and weight loss trials were carried out. These studies were complemented by observations using an optical microscope. The weight loss study allowed the identification of low corrosion rates to the three stainless steels studied.

Heterogeneous nucleation in a glass-forming alloy

NASA Astrophysics Data System (ADS)

Wall, J. J.; Liu, C. T.; Rhim, W.-K.; Li, J. J. Z.; Liaw, P. K.; Choo, H.; Johnson, W. L.

2008-06-01

Nucleation in the undercooled liquid state in the bulk metallic glass-forming composition Zr52.5Cu17.9Ni14.6Al10Ti5 (VIT-105), produced using high purity (PA) and commercial purity (CA) raw materials was investigated using electrostatic levitation and ex situ neutron diffraction. The CA material was observed to have a lower density than the PA sample and crystallized at relatively shallow undercooling. The densities of the samples at temperatures above the solidus showed an oxygen-dependent hysteresis associated with the state change, indicating the presence of oxygen-stabilized intermetallics. The PA alloy exhibited three distinct crystallization modes dependent on the thermal history of the melt, one of which showed a net volume expansion.

7 CFR 58.517 - General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.517 General. Raw materials used for manufacturing cottage cheese shall meet the following quality...

7 CFR 58.517 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.517 General. Raw materials used for manufacturing cottage cheese shall meet the following quality...

40 CFR 122.23 - Concentrated animal feeding operations (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2012 CFR

2012-07-01

... with any raw materials, products, or byproducts including manure, litter, feed, milk, eggs or bedding... manure handling system). (5) The term manure is defined to include manure, bedding, compost and raw... storage area, the raw materials storage area, and the waste containment areas. The animal confinement area...

40 CFR 122.23 - Concentrated animal feeding operations (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2013 CFR

2013-07-01

... with any raw materials, products, or byproducts including manure, litter, feed, milk, eggs or bedding... manure handling system). (5) The term manure is defined to include manure, bedding, compost and raw... storage area, the raw materials storage area, and the waste containment areas. The animal confinement area...

40 CFR 122.23 - Concentrated animal feeding operations (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2011 CFR

2011-07-01

... with any raw materials, products, or byproducts including manure, litter, feed, milk, eggs or bedding... manure handling system). (5) The term manure is defined to include manure, bedding, compost and raw... storage area, the raw materials storage area, and the waste containment areas. The animal confinement area...

40 CFR 122.23 - Concentrated animal feeding operations (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2014 CFR

2014-07-01

... with any raw materials, products, or byproducts including manure, litter, feed, milk, eggs or bedding... manure handling system). (5) The term manure is defined to include manure, bedding, compost and raw... storage area, the raw materials storage area, and the waste containment areas. The animal confinement area...

Inorganic raw materials economy and provenance of chipped industry in some stone age sites of northern and central Italy.

PubMed

Bietti, Amilcare; Boschian, Giovanni; Crisci, Gino Mirocle; Danese, Ermanno; De Francesco, Anna Maria; Dini, Mario; Fontana, Federica; Giampietri, Alessandra; Grifoni, Renata; Guerreschi, Antonio; Liagre, Jérémie; Negrino, Fabio; Radi, Giovanna; Tozzi, Carlo; Tykot, Robert

2004-06-01

An opportunistic and local choice of raw materials is typically attested in the Lower and Middle Paleolithic industries throughout Italy. The quality of the raw material usually affected the flaking technology and quality of the products. In the Upper Paleolithic and the Mesolithic, raw material procurement strategies were more complex. Flint was exploited both locally, in areas where abundant outcrops of raw materials were available (such as the Lessini mountains), and in distant localities, after which it was transported or exchanged over medium/long distances. Different routes of exchange were thus followed in the various periods; good reconstruction of these routes have been provided by a study of the Garfagnana sites in Northern Tuscany, and the Mesolithic deposit of Mondeval de Sora (Dolomites). An interesting example of a Late Upper Paleolithic flint quarry and workshop were found in Abruzzo, in the San Bartolomeo shelter. The extended trade of obsidian from Lipari, Palmarola and Sardinia to the Italian Peninsula is attested in the Neolithic, with some differences concerning the age and different areas.

Sintering, properties and fabrication of Si3N4 + Y2O3 based ceramics

NASA Technical Reports Server (NTRS)

Quackenbush, C. L.; Smith, J. T.; Neil, J. T.; French, K. W.

1983-01-01

Pure silicon nitride shows a remarkable resistance to sintering without the use of densification additives. The present investigation is concerned with results which show the effect of chemical content on sinterability, taking into account the composition, raw material impurities, and processing contaminants. Aspects of sintering are discussed along with strength characteristics, and oxidation relations. Attention is given to phase field I and II materials, phase field III and IV materials, tungsten carbide and oxidation at 600 C, and studies involving shape fabrication by injection molding. It was found that in sintering Si3N4 + Y2O3 an increase in the amount of Y2O3 and, in particular, the addition of Al2O3 enhances the fluidity of the liquid phase.

Characterization of raw and alkali treated new natural cellulosic fiber from Coccinia grandis.L.

PubMed

Senthamaraikannan, P; Kathiresan, M

2018-04-15

The physical, chemical, tensile, crystalline, thermal, and surface morphological properties of raw and alkali treated Coccinia Grandis.L Fibers (CGFs) were characterized for the first time in this work. The results of the chemical analysis indicate that, after alkali treatment, the cellulose content of CGFs increased whereas hemicelluloses, lignin and wax contents decreased. This directly influenced the tensile strength, crystallinity index, thermal stability and the roughness of alkali-treated CGFs. The thermal stability and activation energy of the CGFs improved from 213.4 °C to 220.6 °C and 67.02 kJ/mol to 73.43 kJ/mol, respectively, due to alkali treatment. The statistical approach, Weibull distribution was adopted to analyze the tensile properties. The improved properties of the alkali treated CGF indicate that it could be an appropriate material for reinforcement in polymer composites. Copyright © 2018 Elsevier Ltd. All rights reserved.

7 CFR 58.231 - General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Materials § 58.231 General. All raw materials received at the drying plant shall meet the following quality...

7 CFR 58.231 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Materials § 58.231 General. All raw materials received at the drying plant shall meet the following quality...

Development and characterization of soy-based epoxy resins and pultruded FRP composites

NASA Astrophysics Data System (ADS)

Zhu, Jiang

This dissertation focuses on the development, manufacture and characterization of novel soy-based epoxy FRP composites. Use of alternative epoxy resin systems derived from a renewable resource holds potential for low cost raw materials for the polymer and composite industries. Epoxidized Allyl Soyate (EAS) and Epoxidized Methyl Soyate (EMS) were developed from soybean oil with two chemical modification procedures: transesterification and epoxidation. This research investigates the curing characteristics and thermal and mechanical properties of the neat soyate resin systems. The derived soyate resins have higher reactivity and superior performance compared to commercially available epoxidized soybean oil. An efficient two-step curing method was developed in order to utilize these soyate resins to their full potential. The epoxy co-resin systems with varied soyate resin content were successfully used to fabricate composite material through pultrusion. The pultrusion resin systems with 30 wt% soyate resins yielded improved, or comparable mechanical properties with neat commercial resins. A finite element analysis of the heat transfer and curing process was performed to study the processing characterization on glass/epoxy composite pultrusion. This model can be used to establish baseline process variables and will benefit subsequent optimization. This research demonstrates that soy-based resins, especially EAS, show considerable promise as an epoxy resin supplement for use in polymer and composite structural applications. The new products derived from soybean oil can provide competitive performance, low cost and environmental advantages.

21 CFR 113.81 - Product preparation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Production and Process Controls § 113.81 Product preparation. (a) Before using raw materials and ingredients susceptible to microbiological contamination, the processor shall ensure that those materials and ingredients... by receiving the raw materials and ingredients under a supplier's guarantee that they are suitable...

Application of mathematical model methods for optimization tasks in construction materials technology

NASA Astrophysics Data System (ADS)

Fomina, E. V.; Kozhukhova, N. I.; Sverguzova, S. V.; Fomin, A. E.

2018-05-01

In this paper, the regression equations method for design of construction material was studied. Regression and polynomial equations representing the correlation between the studied parameters were proposed. The logic design and software interface of the regression equations method focused on parameter optimization to provide the energy saving effect at the stage of autoclave aerated concrete design considering the replacement of traditionally used quartz sand by coal mining by-product such as argillite. The mathematical model represented by a quadric polynomial for the design of experiment was obtained using calculated and experimental data. This allowed the estimation of relationship between the composition and final properties of the aerated concrete. The surface response graphically presented in a nomogram allowed the estimation of concrete properties in response to variation of composition within the x-space. The optimal range of argillite content was obtained leading to a reduction of raw materials demand, development of target plastic strength of aerated concrete as well as a reduction of curing time before autoclave treatment. Generally, this method allows the design of autoclave aerated concrete with required performance without additional resource and time costs.

Fly-ash geo-polymer foamed concrete

NASA Astrophysics Data System (ADS)

Kargin, Aleksey; Baev, Vladimir; Mashkin, Nikolay

2017-01-01

In recent years, the interest of researchrs in using fly-ash as a raw material for the geo-polymer synthesis is increasing. Kuzbass region (in Russia) has a large amount of ash wastes generated, which defined the relevace of the study performed in this paper. Results of investigating load-bearing capacity of structural insulating material produced by geo-polymerization of fly-ash of Kemerovo hydro-electric power plant with the addition of complex activator are described in the paper. Hydrogen peroxide solution was used as the foaming agent. The activation time, the temperature of isothermal holding and hardening in normal conditions for all samples were constant. The compressive strength and the mean density of geo-polymer foamed concrete were determined. The influence of the material composition on its properties was revealed. It is found that of the geo-polymer foamed concrete with the optimum composition has hardness of 1,1-3,5 MPa at the density of 400 to 900 kg/m3. Thus, the production of the fly-ash geo-polymer concretes and mortars is feasible, justified and promising.

A Facile Large-Scale Synthesis of Porous SnO2 by Bronze for Superior Lithium Storage and Gas Sensing Properties Through a Wet Chemical Reaction Strategy

NASA Astrophysics Data System (ADS)

Yue, Lu; Ge, Jingjing; Luo, Gaixia; Bian, Kaiting; Yin, Chao; Guan, Rongfeng; Zhang, Wenhui; Zhou, Zheng; Wang, Kaixin; Guo, Xiufeng

2018-03-01

A facile approach to prepare porous SnO2 and SnO2/C composite with Cu-Sn alloy as raw material by wet chemical reaction strategy has been developed. The prepared porous SnO2 and its carbon composite showed homogeneous mesoporous structure and high surface area, displayed superior rate performance and high reversible capacity of 625 mAh g-1 and 1185 mAh g-1 over 800 cycles at 0.4 A g-1, respectively. Compared with commercial SnO2, porous SnO2 sensor presented higher response, faster response/recovery capability, good selectivity and repeatability to ethanol at 180°C.

Effect of storage temperatures and humidity on proximate composition, peroxide value and iodine value of raw cashew nuts.

PubMed

Ajith, Sabna; Pramod, S; Prabha Kumari, C; Potty, V P

2015-07-01

The equilibrium moisture content (EMC) of raw cashew nuts (RCN) were determined using the standard static gravimetric method at 30 °C, 40 °C and 50 °C for relative humidity (RH) ranging from 43 to 90 %. The proximate composition analysis, peroxide value and iodine value of RCN were assessed at this equilibrium stage. The RCN kept under the humidity of 86 and 90 percentage at all studied temperatures developed mold growth within 24-48 h of time. The better storage condition assessed for raw cashew nut is 67 % of RH at 30 °C and the values obtained for EMC, proximate composition analysis, peroxide value and iodine value are within the same range as observed with harvested RCN. Highlights • Raw cashew nut storage condition identified • It was analysed with different temperature (30 (°)C, 40 (°)C and 50 (°)C) and relative humidity (43 %-90 %) • Better storage condition for raw cashew nut is in 67 % of RH at 30 (°)C • In this condition the EMC was 8.11 % as within the range of moisture in harvested RCN.

Enhancement of efficiency of storage and processing of food raw materials using radiation technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gracheva, A. Yu.; Zav’yalov, M. A.; Ilyukhina, N. V.

The work is dedicated to improvement of efficiency of storage and processing of food raw materials using radiation technologies. International practice of radiation processing of food raw materials is presented and an increase in the consumption of irradiated food products is shown. The prospects of using radiation technologies for the processing of food products in Russia are discussed. The results of studies of radiation effects on various food products and packaging film by γ radiation and accelerated electrons are presented.

Seasonal variation in the Dutch bovine raw milk composition.

PubMed

Heck, J M L; van Valenberg, H J F; Dijkstra, J; van Hooijdonk, A C M

2009-10-01

In this study, we determined the detailed composition of and seasonal variation in Dutch dairy milk. Raw milk samples representative of the complete Dutch milk supply were collected weekly from February 2005 until February 2006. Large seasonal variation exists in the concentrations of the main components and milk fatty acid composition. Milk lactose concentration was rather constant throughout the season. Milk true protein content was somewhat more responsive to season, with the lowest content in June (3.21 g/100 g) and the highest content in December (3.38 g/100 g). Milk fat concentration increased from a minimum of 4.10 g/100 g in June to a maximum of 4.57 g/100 g in January. The largest (up to 2-fold) seasonal changes in the fatty acid composition were found for trans fatty acids, including conjugated linoleic acid. Milk protein composition was rather constant throughout the season. Milk unsaturation indices, which were used as an indication of desaturase activity, were lowest in spring and highest in autumn. Compared with a previous investigation of Dutch dairy milk in 1992, the fatty acid composition of Dutch raw milk has changed considerably, in particular with a higher content of saturated fatty acids in 2005 milk.

A study of material composition disclosure practices in green footwear products.

PubMed

Jacques, Jocelise J; Guimarães, Lia B M

2012-01-01

This work is based on the study of pioneering sustainable product development initiatives, and the analysis was guided by the cradle-to-cradle concept, which sees the waste of a given process as raw material for another, just like it happens in nature. Several studies on human factors have focused on factory conditions and workers dealing with product assembly. This research, however, relates more to consumer behavior, product use and end-of-life. The purchase of more environmentally- friendly products, in particular, is heavily influenced by the information made available by the companies. In this scenario, this article discusses three early but notable efforts on green product development, focusing on the disclosure practices adopted by the companies regarding the composition of their products. Research and data collection has focused on the footwear industry, whose products satisfy a basic human need and are ubiquitous worldwide. The use of hazardous materials and chemicals in shoe manufacturing, particularly the use of chromium - a highly toxic element - in addition to toxic solvents and adhesives and non-recyclable synthetic materials can pose serious risks to human health and the environment, even though the consumer usually is not aware of all the relevant characteristics of this kind of product.

[Understanding and development strategy of health food containing Chinese materia medica].

PubMed

Wang, Lin-Yuan; Zhang, Jian-Jun; Wang, Chun; Wang, Jing-Xia; Zhu, Ying-Li; Wang, Jia; Gao, Xue-Min

2016-11-01

Health food containing Chinese materia medica (CMM) conforms to the development demands of the age of big health and the theory of preventive treatment. In the view of health care and improvement of resisting diseases, it plays an important role in the market. It is very necessary to have further study and discussion on health food containing CMM. First of all, by comparing, analyzing and summarizing, the health food containing CMM could be defined as the health food which is qualified in security and functionality evaluation, with the traditional Chinese medicines(TCM) within TCM standards as the main raw materials, and the formulation-composition is based on the theory of TCM. It is characterized by higher safety than medicines, stronger biological activities than common food, multiple forms, abundant raw materials and integrated supervision and management. Secondly, we discussed the research and development (R&D) strategies and rules of health food containing CMM, pointing out that the core tasks of R&D include the investigation of formula, technology and the standards of quality. The fundamental principles of declaration and production include scientificity, rationality, reality and uniformity. Three key requirements (security, functionality and controllability) in the review as well as the process management of R&D and the key-points of risks control were summarized in this paper. Finally, the dynamic trends of policies and regulations related to health food containing CMM were analyzed in the view of registration, recording, raw materials and functions, and then related suggestions were proposed. Therefore, this article will be helpful in overall understanding the health food containing CMM and play a guiding role for its research and development. Copyright© by the Chinese Pharmaceutical Association.

Preliminary study on antifungal effect of commercial essential oils against white rot fungi

NASA Astrophysics Data System (ADS)

Khalid, Nurul Izzaty; Baharum, Azizah; Daud, Fauzi

2015-09-01

Protecting and preserving wood plastic composite from deterioration caused by fungal attack is a high challenge issue to cater nowadays. The objective of this study was to carry out a screening test towards antifungal effect of essential oil and to investigate the potential of raw materials that will be used as basic material for manufacturing wood plastic composite against white rot fungi. Essential oils from four types of natural products comprising cinnamon, lemongrass, lavender and geranium have been screened for their ability to inhibit five types of white rot fungi species which are Lentinus squarrosulus, Pleuorotus pulmonarius, Lentinus sp., Pleuorotus sajor-caju and Lignosus rhinocerus. The antifungal evaluation showed that no inhibitory effect against tested white rot fungi since the mycelia completely filled the plates. From the observation, mycelia of L. squarrosulus, P. pulmonarius and Lentinus sp. were found to filled the surface of falcon tubes with rubber sawdust after 15 days. Mycelia of L. squarrosulus and P. pulmonarius also were found to completely covered the surface of media that contain polypropylene and maleic anhydride grafted polypropylene on it. Therefore, this report proved that the main materials that will be applicable in manufacturing of wood plastic composite had potential to be degraded by this type of fungal attack.

Material Characterization of Microsphere-Based Scaffolds with Encapsulated Raw Materials

PubMed Central

Sridharan, BanuPriya; Mohan, Neethu; Berkland, Cory J.; Detamore, Michael S.

2016-01-01

“Raw materials,” or materials capable of serving both as building blocks and as signals, which are often but not always natural materials, are taking center stage in biomaterials for contemporary regenerative medicine. In osteochondral tissue engineering, a field leveraging the underlying bone to facilitate cartilage regeneration, common raw materials include chondroitin sulfate (CS) for cartilage and β-tricalcium phosphate (TCP) for bone. Building on our previous work with gradient scaffolds based on microspheres, here we delved deeper into the characterization of individual components. In the current study, the release of CS and TCP from poly(D,L-lactic-co-glycolic acid) (PLGA) microsphere-based scaffolds was evaluated over a time period of 4 weeks. Raw material encapsulated groups were compared to ‘blank’ groups and evaluated for surface topology, molecular weight, and mechanical performance as a function of time. The CS group may have led to increased surface porosity, and the addition of CS improved the mechanical performance of the scaffold. The finding that CS was completely released into the surrounding media by 4 weeks has a significant impact on future in vivo studies, given rapid bioavailability. The addition of TCP seemed to contribute to the rough external appearance of the scaffold. The current study provides an introduction to degradation patterns of homogenous raw material encapsulated scaffolds, providing characterization data to advance the field of microsphere-based scaffolds in tissue engineering. PMID:27040236

Rapid bacteriological screening of cosmetic raw materials by using bioluminescence.

PubMed

Nielsen, P; Van Dellen, E

1989-01-01

Incoming cosmetic raw materials are routinely tested for microbial content. Standard plate count methods require up to 72 h. A rapid, sensitive, and inexpensive raw material screening method was developed that detects the presence of bacteria by means of ATP (bioluminescence). With a 24-h broth enrichment, the minimum bacterial ATP detection threshold of 1 cfu/g sample can be achieved using purified firefly luciferin-luciferase and an ATP releasing reagent. By using this rapid screen, microbiologically free material may be released for production within 24 h, while contaminated material undergoes further quantitative and identification testing. In order for a raw material to be validated for this method it must be evaluated for (1) a potential nonmicrobial light-contributing reaction resulting in a false positive or, (2) degradation of the ATP giving a false negative, and (3) confirmation that the raw material has not overwhelmed the buffering capacity of the enrichment broth. The key criteria for a rapid screen was the sensitivity to detect less than one colony forming unit per g product, the speed to do this within 24 h, and cost efficiency. Bioluminescence meets these criteria. With an enrichment step, it can detect less than one cfu/g sample. After the enrichment step, analysis time per sample is approximately 2 min and the cost for material and reagents is less than one dollar per sample.

Titanium nitride plasma-chemical synthesis with titanium tetrachloride raw material in the DC plasma-arc reactor

NASA Astrophysics Data System (ADS)

Kirpichev, D. E.; Sinaiskiy, M. A.; Samokhin, A. V.; Alexeev, N. V.

2017-04-01

The possibility of plasmochemical synthesis of titanium nitride is demonstrated in the paper. Results of the thermodynamic analysis of TiCl4 - H2 - N2 system are presented; key parameters of TiN synthesis process are calculated. The influence of parameters of plasma-chemical titanium nitride synthesis process in the reactor with an arc plasmatron on characteristics on the produced powders is experimentally investigated. Structure, chemical composition and morphology dependencies on plasma jet enthalpy, stoichiometric excess of hydrogen and nitrogen in a plasma jet are determined.

Investigation of Test Methods, Material Properties, and Processes for Solar Cell Encapsulants

NASA Technical Reports Server (NTRS)

Willis, P. B.; Baum, B.

1979-01-01

The reformulation of a commercial grade of ethylene/vinyl acetate copolymer for use as a pottant in solar cell module manufacture was investigated. Potentially successful formulations were prepared by compounding the raw polymer with antioxidants, ultraviolet absorbers and crosslinking agents to yield stabilized and curable compositions. The resulting elastomer was found to offer low cost (approximately $0.80/lb.), low temperature processability, high transparency (91% transmission), and low modulus. Cured specimens of the final formulation endured 4000 hours of fluorescent sunlamp radiation without change which indicates excellent stability.

Biodegradation of natural reinforcing fillers for polymer composites

NASA Astrophysics Data System (ADS)

Mastalygina, E. E.; Pantyukhov, P. V.; Popov, A. A.

2018-05-01

Twelve different natural raw materials were selected as possible fillers for eco-friendly biocomposites. The target was to find the most biodegradable ones. Two mycological tests were held: in the aqueous and agar media. It was found that two tests showed different results. In aqueous media, the fillers with a high content of water-soluble and easy-hydrolysed compounds demostrated the most intensive biofouling. In agar media, the entire filler was exposed to biodigestion by fungi. Therefore, multi-compound fillers with a set of different macro- and microelements were more biodegradable than others.

Minimally refined biomass fuel

DOEpatents

Pearson, Richard K.; Hirschfeld, Tomas B.

1984-01-01

A minimally refined fluid composition, suitable as a fuel mixture and derived from biomass material, is comprised of one or more water-soluble carbohydrates such as sucrose, one or more alcohols having less than four carbons, and water. The carbohydrate provides the fuel source; water solubilizes the carbohydrates; and the alcohol aids in the combustion of the carbohydrate and reduces the vicosity of the carbohydrate/water solution. Because less energy is required to obtain the carbohydrate from the raw biomass than alcohol, an overall energy savings is realized compared to fuels employing alcohol as the primary fuel.

31 CFR 545.413 - Importation of goods from third countries; transshipments.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; transshipments. (a) Importation into the United States from third countries of goods containing raw materials or... raw materials or components have been incorporated into manufactured products or otherwise...

The Effect of Coloring and Compacting Pressure Paving Block by Adding 5 Wt.% Fly Ash in The Compressive Strength

NASA Astrophysics Data System (ADS)

Nurzal; Nursyuhada, Aries

2017-12-01

This research aims based on SNI 03-0691-1996 to investigate the effect of coloring and compacting pressure with the addition of 5 wt.% fly ash (Fa) on compressive strength. Fa derived from waste material coal-fired Sijantang Sawahlunto thermal power plant. The growing production of Fa caused negative environmental impact. So, one of the solutions to overcome that effects is to use the Fa as a raw material for paving block mixture that can reduce the cost of raw material and increase its strength. Paving blocks are gray and red with 0 wt.%, 5 wt.% Fa + Pb composition. Compaction pressure variations 55, 65, 75, 85 and 95 Kg/cm2. The drying time for 35 days. Specimens were produced in the form of rectangular bar (length, L = 20 cm, width, B = 10 cm, thickness, W = 6 cm). The test results showed that the addition of 5 wt% FA has a compressive strength value higher than 0 wt%. The red color has a compressive strength lower than the gray color paving block caused the red color (Iron Oxide) is less binding at the time of mixing the material. Gray and red Paving blocks both increase in each additional compaction pressure, because the higher the compaction pressure will increase the bond between the particles so porosity is reduced increased compressive strength. The overall data, the gray paving block with the composition of 5 wt% FA at compaction pressure 95 kg/cm2 with the optimal compressive strength value of 36.1 MPa and the lowest value is found in the red color paving block at 0 wt% FA at a pressure of 55 kg/cm2 with a value of 6.5 MPa. Gray and red Color paving blocks has a compressive strength quality based on SNI 03-0691-1996.

Stabilization of cesium in alkali-activated municipal solid waste incineration fly ash and a pyrophyllite-based system.

PubMed

Shiota, Kenji; Nakamura, Takafumi; Takaoka, Masaki; Aminuddin, Siti Fatimah; Oshita, Kazuyuki; Fujimori, Takashi

2017-11-01

Environmentally sound treatments are required to dispose of municipal solid waste incineration fly ash (MSWIFA) contaminated with radioactive cesium (Cs) from the Fukushima Daiichi nuclear power plant accident in Japan. This study focuses on the stabilization of Cs using an alkali-activated MSWIFA and pyophyllite-based system. Three composite solid products were synthesized after mixtures of raw materials (dehydrated pyrophyllite, MSWIFA, 14 mol/L aqueous sodium hydroxide, and sodium silicate solution) were cured at 105 °C for 24 h. Three types of MSWIFAs were prepared as raw fly ash, raw fly ash with 0.1% CsCl, and raw fly ash with 40% CsCl to understand the stabilization mechanism of Cs. Cs stabilization in two solid products was successful, with less than 6.9% leaching observed from two types tests, and was partly successful for the solid product with the highest concentration of Cs. X-ray diffraction showed that all of the solid products produced several crystalline phases, and that pollucite was formed in the highest Cs concentration product. The X-ray absorption fine structure and scanning electron microscopy with X-ray analysis suggested that most Cs species formed pollucite in the two solid products from MSWIFA with added CsCl. This system provides a technique for the direct stabilization of Cs in MSWIFA. Copyright © 2017 Elsevier Ltd. All rights reserved.

Competitive Advantage Market Analysis | Energy Analysis | NREL

Science.gov Websites

Study An NREL market assessment of raw and intermediate materials, equipment, and products for equipment for c-Si PV Abundant raw materials for production of moisture barrier films, glass, aluminum

7 CFR 58.322 - Cream.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58... derived from raw material meeting the requirements as listed under §§ 58.132 through 58.138 of this...

7 CFR 58.322 - Cream.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58... derived from raw material meeting the requirements as listed under §§ 58.132 through 58.138 of this...

40 CFR 63.1251 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ingredient means any material that is intended to furnish pharmacological activity or other direct effect in... this section. Consumption means the quantity of all HAP raw materials entering a process in excess of... as added as a raw material, consumption includes the quantity generated in the process. Container, as...

40 CFR 63.1251 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ingredient means any material that is intended to furnish pharmacological activity or other direct effect in... this section. Consumption means the quantity of all HAP raw materials entering a process in excess of... as added as a raw material, consumption includes the quantity generated in the process. Container, as...

40 CFR 63.1251 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ingredient means any material that is intended to furnish pharmacological activity or other direct effect in... this section. Consumption means the quantity of all HAP raw materials entering a process in excess of... as added as a raw material, consumption includes the quantity generated in the process. Container, as...

Smart Natural Fiber Reinforced Plastic (NFRP) Composites Based On Recycled Polypropylene in The Presence Kaolin

NASA Astrophysics Data System (ADS)

Suharty, N. S.; Ismail, H.; Diharjo, K.; Handayani, D. S.; Lestari, W. A.

2017-07-01

Composites contain double filler material which act as reinforcement and flame retardants of recycled polypropylene (rPP)/kaolin(Kao)/palm oil empty bunch fiber (PEBF) have been succesfully prepared. The composites were synthesized through reactively solution method, using coupling agent PP-g-AA and compatibilizer DVB. The effect of double filler [Kao/PEBF] were investigated flexural strength (FS), inflammability, and morphology. Mechanical testing result in accordance to ASTM D790, the FS of rPP/DVB/PP-g-AA/Kao+ZB/PEBF composite was 48% higher than that of rPP matrix. Moreover, flexural modulus (FM) was significantly improved by 56% as compared to that of rPP matrix. The scanning electron images (SEM) shown good dispersion of [Ka/PEBF] and good filler-matrix interaction. The inflammability testing result which is tested using ASTM D635, showed that the flame resistance of rPP/DVB/PP-g-AA/Kao+ZB/PEBF composite was improve by increasing of time to ignition (TTI) about 857% and burning rate (BR) decreasing to 66% compared to the raw material rPP matrix. In the same time, the addition of 20% (w/w) PEBF as a second filler to form rPP/DVB/PP-g-AA/Kao+ZB/PEBF composites (F5) is able to increase: the FS by 17.5%, the FM by 19%, the TTI by 7.6% and the BR by 3.7% compared to the composite without PEBF (F2).

The properties of weft knitted fabric medical and preventive treatment action using eco-raw materials

NASA Astrophysics Data System (ADS)

Halavska, L.; Batrak, O.

2016-07-01

A new trend in the world is the clothing production using the new types of ecological raw materials application - milk, pineapple, coconut, hemp, banana, eucalyptus, clams, corn, bamboo, soya, nettle yarn. This makes it possible to create textile materials of new generation with unique antibacterial and antiseptic properties. Such materials have a positive preventive and sometimes therapeutic effect on people, and their health. Eco-raw materials clothing is able to protect the human body from the environment harmful effects: cold, heat, rain, dust, opportunely remove from underclothing layer the steam and gases, sweat; maintain in underclothing layer the necessary microclimate for normal organism functioning. Study of knitwear consumer properties, produced with eco-materials, is an urgent task of the world vector, directed on ecological environmental protection. This paper presents the research results of hygroscopicity and capillarity weft knitted fabrics, what knitted from different types of eco-raw materials: bamboo yarn, yarn containing soybean and nettle yarn. Character of influence of the liquid raising level changes depending on the experiment time and the knitting structure is revealed.

Upgrading nickel content of limonite nickel ore through pelletization, selective reduction and magnetic separation

NASA Astrophysics Data System (ADS)

Mayangsari, W.; Prasetyo, A. B.; Prasetiyo, Puguh

2018-04-01

Limonite nickel ore has potency to utilize as raw material for ferronickel or nickel matte, since it has low grade nickel content, thus process development is needed to find the acceptable process for upgrading nickel. The aim of this research is to determine upgrading of Ni content as result of selective reduction of limonite nickel pellet continued by magnetic separation as effect of temperature and time reduction as well as coal and CaSO4 addition. There are four steps to perform this research, such as preparation including characterization of raw ore and pelletization, selective reduction, magnetic separation and characterization of products by using AAS, XRD and SEM. Based on the result study, pellet form can upgrade 77.78% higher than powder form. Upgrading of Ni and Fe content was up to 3fold and 1.5fold respectively from raw ore used when reduced at 1100°C for 60 minutes with composition of coal and CaSO4, both 10%. The excess of CaSO4 addition caused fayalite formation. Moreover, S2 from CaSO4 also support to reach low melting point and enlardge particle size of metal formed.

From electronic consumer products to e-wastes: Global outlook, waste quantities, recycling challenges.

PubMed

Tansel, Berrin

2017-01-01

Advancements in technology, materials development, and manufacturing processes have changed the consumer products and composition of municipal solid waste (MSW) since 1960s. Increasing quantities of discarded consumer products remain a major challenge for recycling efforts, especially for discarded electronic products (also referred as e-waste). The growing demand for high tech products has increased the e-waste quantities and its cross boundary transport globally. This paper reviews the challenges associated with increasing e-waste quantities. The increasing need for raw materials (especially for rare earth and minor elements) and unregulated e-waste recycling operations in developing and underdeveloped counties contribute to the growing concerns for e-waste management. Although the markets for recycled materials are increasing; there are major challenges for development of the necessary infrastructure for e-waste management and accountability as well as development of effective materials recovery technologies and product design. Copyright © 2016 Elsevier Ltd. All rights reserved.

Static viscoelasticity of biomass polyethylene composites

NASA Astrophysics Data System (ADS)

Yang, Keyan; Cai, Hongzhen; Yi, Weiming; Zhang, Qingfa; Zhao, Kunpeng

The biomass polyethylene composites filled with poplar wood flour, rice husk, cotton stalk or corn stalk were prepared by extrusion molding. The static viscoelasticity of composites was investigated by the dynamic thermal mechanical analyzer (DMA). Through the stress-strain scanning, it is found that the linear viscoelasticity interval of composites gradually decreases as the temperature rises, and the critical stress and strain values are 0.8 MPa and 0.03% respectively. The experiment shows that as the temperature rises, the creep compliance of biomass polyethylene composites is increased; under the constant temperature, the creep compliance decreases with the increase of content of biomass and calcium carbonate. The biomass and calcium carbonate used to prepare composites as filler can improve damping vibration attenuation and reduce stress deformation of composites. The stress relaxation modulus of composites is reduced and the relaxation rate increases at the higher temperature. The biomass and calcium carbonate used to prepare composites as filler not only can reduce costs, but also can increase stress relaxation modulus and improve the size thermostability of composites. The corn stalk is a good kind of biomass raw material for composites since it can improve the creep resistance property and the stress relaxation resistance property of composites more effectively than other three kinds of biomass (poplar wood flour, rice husk and cotton stalk).

An artificial photosynthesis anode electrode composed of a nanoparticulate photocatalyst film in a visible light responsive GaN-ZnO solid solution system

NASA Astrophysics Data System (ADS)

Imanaka, Yoshihiko; Anazawa, Toshihisa; Manabe, Toshio; Amada, Hideyuki; Ido, Sachio; Kumasaka, Fumiaki; Awaji, Naoki; Sánchez-Santolino, Gabriel; Ishikawa, Ryo; Ikuhara, Yuichi

2016-10-01

The artificial photosynthesis technology known as the Honda-Fujishima effect, which produces oxygen and hydrogen or organic energy from sunlight, water, and carbon dioxide, is an effective energy and environmental technology. The key component for the higher efficiency of this reaction system is the anode electrode, generally composed of a photocatalyst formed on a glass substrate from electrically conductive fluorine-doped tin oxide (FTO). To obtain a highly efficient electrode, a dense film composed of a nanoparticulate visible light responsive photocatalyst that usually has a complicated multi-element composition needs to be deposited and adhered onto the FTO. In this study, we discovered a method for controlling the electronic structure of a film by controlling the aerosol-type nanoparticle deposition (NPD) condition and thereby forming films of materials with a band gap smaller than that of the prepared raw material powder, and we succeeded in extracting a higher current from the anode electrode. As a result, we confirmed that a current approximately 100 times larger than those produced by conventional processes could be obtained using the same material. This effect can be expected not only from the materials discussed (GaN-ZnO) in this paper but also from any photocatalyst, particularly materials of solid solution compositions.

Isolating the effect of pore size distribution on electrochemical double-layer capacitance using activated fluid coke

NASA Astrophysics Data System (ADS)

Zuliani, Jocelyn E.; Tong, Shitang; Kirk, Donald W.; Jia, Charles Q.

2015-12-01

Electrochemical double-layer capacitors (EDLCs) use physical ion adsorption in the capacitive electrical double layer of high specific surface area (SSA) materials to store electrical energy. Previous work shows that the SSA-normalized capacitance increases when pore diameters are less than 1 nm. However, there still remains uncertainty about the charge storage mechanism since the enhanced SSA-normalized capacitance is not observed in all microporous materials. In previous studies, the total specific surface area and the chemical composition of the electrode materials were not controlled. The current work is the first reported study that systematically compares the performance of activated carbon prepared from the same raw material, with similar chemical composition and specific surface area, but different pore size distributions. Preparing samples with similar SSAs, but different pores sizes is not straightforward since increasing pore diameters results in decreasing the SSA. This study observes that the microporous activated carbon has a higher SSA-normalized capacitance, 14.1 μF cm-2, compared to the mesoporous material, 12.4 μF cm-2. However, this enhanced SSA-normalized capacitance is only observed above a threshold operating voltage. Therefore, it can be concluded that a minimum applied voltage is required to induce ion adsorption in these sub-nanometer micropores, which increases the capacitance.

Fish protein hydrolysates: proximate composition, amino acid composition, antioxidant activities and applications: a review.

PubMed

Chalamaiah, M; Dinesh Kumar, B; Hemalatha, R; Jyothirmayi, T

2012-12-15

The fish processing industry produces more than 60% by-products as waste, which includes skin, head, viscera, trimmings, liver, frames, bones, and roes. These by-product wastes contain good amount of protein rich material that are normally processed into low market-value products, such as animal feed, fish meal and fertilizer. In view of utilizing these fish industry wastes, and for increasing the value to several underutilised fish species, protein hydrolysates from fish proteins are being prepared by several researchers all over the world. Fish protein hydrolysates are breakdown products of enzymatic conversion of fish proteins into smaller peptides, which normally contain 2-20 amino acids. In recent years, fish protein hydrolysates have attracted much attention of food biotechnologists due to the availability of large quantities of raw material for the process, and presence of high protein content with good amino acid balance and bioactive peptides (antioxidant, antihypertensive, immunomodulatory and antimicrobial peptides). Copyright © 2012 Elsevier Ltd. All rights reserved.

Synthesis and characterization of a BaGdF5:Tb glass ceramic as a nanocomposite scintillator for x-ray imaging.

PubMed

Lee, Gyuhyon; Struebing, Christian; Wagner, Brent; Summers, Christopher; Ding, Yong; Bryant, Alex; Thadhani, Naresh; Shedlock, Daniel; Star-Lack, Josh; Kang, Zhitao

2016-05-20

Transparent glass ceramics with embedded light-emitting nanocrystals show great potential as low-cost nanocomposite scintillators in comparison to single crystal and transparent ceramic scintillators. In this study, cubic structure BaGdF5:Tb nanocrystals embedded in an aluminosilicate glass matrix are reported for potential high performance MeV imaging applications. Scintillator samples with systematically varied compositions were prepared by a simple conventional melt-quenching method followed by annealing. Optical, structural and scintillation properties were characterized to guide the design and optimization of selected material systems, aiming at the development of a system with higher crystal volume and larger crystal size for improved luminosity. It is observed that enhanced scintillation performance was achieved by tuning the glass matrix composition and using GdF3 in the raw materials, which served as a nucleation agent. A 26% improvement in light output was observed from a BaGdF5:Tb glass ceramic with addition of GdF3.

The use of carbon stable isotope ratios in drugs characterization

NASA Astrophysics Data System (ADS)

Magdas, D. A.; Cristea, G.; Bot, A.; Mirel, V.

2013-11-01

Isotopic Ratio Mass Spectrometry (IRMS) is an effective toll to be used for drug product authentication. The isotopic composition could be used to assist in the differentiation between batches of drugs and assist in the identification of counterfeit materials on the market. Only two factors affect the isotopic ratios in pharmaceutical components: the isotopic composition of the raw materials and the synthetic processes performed upon them. Counterfeiting of pharmaceutical drugs threatens consumer confidence in drug products companies' economical well-being. In this preliminary study, the analyzed samples consist in two types of commercially available analgesics, which were purchases from Romanian pharmacies. Differences in δ13C between batches from -29.7 to -31.6% were observed, demonstrating that this method can be used to differentiate among individual drug batches and subsequently identify counterfeits on the market. On the other hand, carbon isotopic ratios differences among producers were recorded, the variations being between -31.3 to -34.9% for the same type of analgesic, but from different manufactures.

Removal of Cd (II) from synthetic wastewater by alginate-Ayous wood sawdust (Triplochiton scleroxylon) composite material.

PubMed

Njimou, Jacques Romain; Măicăneanu, Andrada; Indolean, Cerasella; Nanseu-Njiki, Charles Péguy; Ngameni, Emmanuel

2016-01-01

The biosorption characteristics of Cd (II) ions from synthetic wastewater using raw Ayous wood sawdust (Triplochiton scleroxylon), r-AS, immobilized by sodium alginate were investigated with respect to pH, biomass quantity, contact time, initial concentration of heavy metal, temperature and stirring rate. The experimental data fitted well with the Langmuir isotherm, suggesting that monolayer adsorption of the cadmium ions onto alginate-Ayous sawdust composite (a-ASC). The obtained monolayer adsorption capacity of a-ASC for Cd (II) was 6.21 mg/g. From the Dubinin-Radushkevich isotherm model, a 5.39 kJ/mol value for the mean free energy was calculated, indicating that Cd (II) biosorption could include an important physisorption stage. Thermodynamic calculations showed that the Cd (II) biosorption process was feasible, endothermic and spontaneous in nature under examined conditions. The results indicated that a-ASC could be an alternative material replacing more costly adsorbents used for the removal of heavy metals.

Influence of raw material properties upon critical quality attributes of continuously produced granules and tablets.

PubMed

Fonteyne, Margot; Wickström, Henrika; Peeters, Elisabeth; Vercruysse, Jurgen; Ehlers, Henrik; Peters, Björn-Hendrik; Remon, Jean Paul; Vervaet, Chris; Ketolainen, Jarkko; Sandler, Niklas; Rantanen, Jukka; Naelapää, Kaisa; De Beer, Thomas

2014-07-01

Continuous manufacturing gains more and more interest within the pharmaceutical industry. The International Conference of Harmonisation (ICH) states in its Q8 'Pharmaceutical Development' guideline that the manufacturer of pharmaceuticals should have an enhanced knowledge of the product performance over a range of raw material attributes, manufacturing process options and process parameters. This fits further into the Process Analytical Technology (PAT) and Quality by Design (QbD) framework. The present study evaluates the effect of variation in critical raw material properties on the critical quality attributes of granules and tablets, produced by a continuous from-powder-to-tablet wet granulation line. The granulation process parameters were kept constant to examine the differences in the end product quality caused by the variability of the raw materials properties only. Theophylline-Lactose-PVP (30-67.5-2.5%) was used as model formulation. Seven different grades of theophylline were granulated. Afterward, the obtained granules were tableted. Both the characteristics of granules and tablets were determined. The results show that differences in raw material properties both affect their processability and several critical quality attributes of the resulting granules and tablets. Copyright © 2014 Elsevier B.V. All rights reserved.

An integrated production-inventory model for food products adopting a general raw material procurement policy

NASA Astrophysics Data System (ADS)

Fauza, G.; Prasetyo, H.; Amanto, B. S.

2018-05-01

Studies on an integrated production-inventory model for deteriorating items have been done extensively. Most of the studies define deterioration as physical depletion of some inventories over time. This definition may not represent the deterioration characteristics of food products. The quality of food production decreases over time while the quantity remains the same. Further, in the existing models, the raw material is replenished several times (or at least once) within one production cycle. In food industries, however, a food company, for several reasons (e.g., the seasonal raw materials, discounted price, etc.) sometimes will get more benefit if it orders raw materials in a large quantity. Considering this fact, this research, therefore, is aimed at developing a more representative inventory model by (i) considering the quality losses in food and (ii) adopting a general raw material procurement policy. A mathematical model is established to represent the proposed policy in which the total profit of the system is the objective function. To evaluate the performance of the model, a numerical test was conducted. The numerical test indicates that the developed model has better performance, i.e., the total profit is 2.3% higher compared to the existing model.

The 1995 Medical Device Technology raw materials survey.

PubMed

Pearson, L S

1995-09-01

Using information supplied by manufacturers, this article reports on the use of raw materials and compounding and conversion practices in the European medical device manufacturing industry. The findings of the survey provide an indication of which materials are being used and how frequently, and the process of selecting suppliers.

Exposure to perfluorinated compounds in Catalonia, Spain, through consumption of various raw and cooked foodstuffs, including packaged food.

PubMed

Jogsten, Ingrid Ericson; Perelló, Gemma; Llebaria, Xavier; Bigas, Esther; Martí-Cid, Roser; Kärrman, Anna; Domingo, José L

2009-07-01

In this study, the role that some food processing and packaging might play as a source of perfluorinated compounds (PFCs) through the diet was assessed. The levels of PFCs were determined in composite samples of veal steak (raw, grilled, and fried), pork loin (raw, grilled, and fried), chicken breast (raw, grilled, and fried), black pudding (uncooked), liver lamb (raw), marinated salmon (home-made and packaged), lettuce (fresh and packaged), pate of pork liver, foie gras of duck, frankfurt, sausages, chicken nuggets (fried), and common salt. Among the 11 PFCs analyzed, only PFHxS, PFOS, PFHxA, and PFOA were detected in at least one composite sample, while the levels of the remaining PFCs (PFBuS, PFHpA, PFNA, PFDA, PFUnDA, and PFDoDA) were under their respective detection limits. PFOS was the compound most frequently detected, being found in 8 of the 20 food items analyzed, while PFHxA was detected in samples of raw veal, chicken nuggets, frankfurt, sausages, and packaged lettuce. According to the results of the present study, it is not sufficiently clear if cooking with non-stick cookware, or packaging some foods, could contribute to a higher human exposure to PFCs.

Creating a Learning-Friendly Curriculum.

ERIC Educational Resources Information Center

Donovan, Michael P.

1997-01-01

Argues against a type of program evaluation of undergraduate institutions that assumes students are products. Proposes that if students are products, then students are raw materials. Discusses the philosophical problems of considering students as raw materials. (DDR)

60. INTERIOR VIEW OF THE RAW MATERIALS BUILDING, LOOKING AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

60. INTERIOR VIEW OF THE RAW MATERIALS BUILDING, LOOKING AT THE POIDOMETER AND WEIGHING MACHINE. MAY 5, 1919. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

Comprehensive NMR analysis of compositional changes of black garlic during thermal processing.

PubMed

Liang, Tingfu; Wei, Feifei; Lu, Yi; Kodani, Yoshinori; Nakada, Mitsuhiko; Miyakawa, Takuya; Tanokura, Masaru

2015-01-21

Black garlic is a processed food product obtained by subjecting whole raw garlic to thermal processing that causes chemical reactions, such as the Maillard reaction, which change the composition of the garlic. In this paper, we report a nuclear magnetic resonance (NMR)-based comprehensive analysis of raw garlic and black garlic extracts to determine the compositional changes resulting from thermal processing. (1)H NMR spectra with a detailed signal assignment showed that 38 components were altered by thermal processing of raw garlic. For example, the contents of 11 l-amino acids increased during the first step of thermal processing over 5 days and then decreased. Multivariate data analysis revealed changes in the contents of fructose, glucose, acetic acid, formic acid, pyroglutamic acid, cycloalliin, and 5-(hydroxymethyl)furfural (5-HMF). Our results provide comprehensive information on changes in NMR-detectable components during thermal processing of whole garlic.

Catalytic transformation of waste polymers to fuel oil.

PubMed

Keane, Mark A

2009-01-01

Waste not, want not: The increase in waste polymer generation, which continues to exceed recycle, represents a critical environmental burden. However, plastic waste may be viewed as a potential resource and, with the correct treatment, can serve as hydrocarbon raw material or as fuel oil, as described in this Minireview.Effective waste management must address waste reduction, reuse, recovery, and recycle. The consumption of plastics continues to grow, and, while plastic recycle has seen a significant increase since the early 1990s, consumption still far exceeds recycle. However, waste plastic can be viewed as a potential resource and can serve, with the correct treatment, as hydrocarbon raw material or as fuel oil. This Minireview considers the role of catalysis in waste polymer reprocessing and provides a critical overview of the existing waste plastic treatment technologies. Thermal pyrolysis results in a random scissioning of the polymer chains, generating products with varying molecular weights. Catalytic degradation provides control over the product composition/distribution and serves to lower significantly the degradation temperature. Incineration of waste PVC is very energy demanding and can result in the formation of toxic chloro emissions. The efficacy of a catalytic transformation of PVC is also discussed.

Using mixture design of experiments to assess the environmental impact of clay-based structural ceramics containing foundry wastes.

PubMed

Coronado, M; Segadães, A M; Andrés, A

2015-12-15

This work describes the leaching behavior of potentially hazardous metals from three different clay-based industrial ceramic products (wall bricks, roof tiles, and face bricks) containing foundry sand dust and Waelz slag as alternative raw materials. For each product, ten mixtures were defined by mixture design of experiments and the leaching of As, Ba, Cd, Cr, Cu, Mo, Ni, Pb, and Zn was evaluated in pressed specimens fired simulating the three industrial ceramic processes. The results showed that, despite the chemical, mineralogical and processing differences, only chrome and molybdenum were not fully immobilized during ceramic processing. Their leaching was modeled as polynomial equations, functions of the raw materials contents, and plotted as response surfaces. This brought to evidence that Cr and Mo leaching from the fired products is not only dependent on the corresponding contents and the basicity of the initial mixtures, but is also clearly related with the mineralogical composition of the fired products, namely the amount of the glassy phase, which depends on both the major oxides contents and the firing temperature. Copyright © 2015 Elsevier B.V. All rights reserved.

[Amaranth bars enriched with fructans: acceptability and nutritional value].

PubMed

Dias Capriles, Vanessa; Gomes Arêas, José Alfredo

2010-09-01

There is an increasing appeal for convenience foods with potential health benefits to the consumer. Raw materials with high nutritional value and functional properties must be used on the development of these food products. Amaranth is a gluten-free grain with high nutrition value. Inulin and oligofructose are prebiotic ingredients presenting effects as the enhancement of calcium absorption. Amaranth bars enriched with inulin and oligofructose were developed in the flavors: banana, Brazilian nuts and dried grape, coconut, peach, strawberry and wall nut. The proximate composition were determined and compared to commercial cereal bars, available in traditional (n=59), light (n=60), diet (n=8), with soy (n=10) and quinoa (n=1) categories. Amaranth bars present mean global acceptance values from 6.3 to 7.6 on a 9-point hedonic scale, nutritional advantages as compared to commercial cereal bars (caloric reduction and higher levels of dietary fiber). Although amaranth is an unknown raw material in Brazil, it shows good potential to be used in the manufacturing of ready-to-eat products. As they are gluten free, these amaranth bars are also an alternative product for celiacs, also contributing to the enhancement of calcium absorption, a problem frequently observed in these patients.

Characterization of impurities present on Tihimatine (Hoggar) quartz, Algeria

NASA Astrophysics Data System (ADS)

Anas Boussaa, S.; Kheloufi, A.; Boutarek Zaourar, N.

2017-11-01

Many of today's advanced materials depend on quartz as a raw material. Quartz usually contains abundant inclusions, both solid and liquid, and due to the number of these inclusions and their small size, complete separation is most difficult. Typical properties of raw quartz that must be characterized are: Size and Chemical composition of inclusions, their spatial distribution, localization of isomorphic substitutional elements (e.g. Al, Fe). The aim of this study has been to test experimental methods for investigating some inclusions (impurities) present in the Tihimatine quartz from El Hoggar region deposits (southern Algeria) using X Ray Fluorescence, scanning electron microscopy, optical Microscopy with reflected and transmitted lights, infra-red spectrometer, Raman spectrometer. Despite the high concentration of SiO2 in studied quartz reaching 98%, several harmful inclusions were found and identified as hematite, anatase, muscovite, graphite, it contains: Fe, Ti, Al, K, Ca. Some fluid inclusions were found. We detect the presence of carbon dioxide and water using raman spectroscopy. The repartition of solid impurities is aleatory and not homogeneous with maximum size of 10 μm. Concerning the fluid impurities, their diameter vary between 5 and 20 μm and their repartition is aleatory.

Raw material procurement for termite fishing tools by wild chimpanzees in the Issa valley, Western Tanzania.

PubMed

Almeida-Warren, Katarina; Sommer, Volker; Piel, Alex K; Pascual-Garrido, Alejandra

2017-10-01

Chimpanzee termite fishing has been studied for decades, yet the selective processes preceding the manufacture of fishing tools remain largely unexplored. We investigate raw material selection and potential evidence of forward planning in the chimpanzees of Issa valley, western Tanzania. Using traditional archaeological methods, we surveyed the location of plants from where chimpanzees sourced raw material to manufacture termite fishing tools, relative to targeted mounds. We measured raw material abundance to test for availability and selection. Statistics included Chi-Squared, two-tailed Wilcoxon, and Kruskall-Wallace tests. Issa chimpanzees manufactured extraction tools only from bark, despite availability of other suitable materials (e.g., twigs), and selected particular plant species as raw material sources, which they often also exploit for food. Most plants were sourced 1-16 m away from the mound, with a maximum of 33 m. The line of sight from the targeted mound was obscured for a quarter of these plants. The exclusive use of bark tools despite availability of other suitable materials indicates a possible cultural preference. The fact that Issa chimpanzees select specific plant species and travel some distance to source them suggests some degree of selectivity and, potentially, forward planning. Our results have implications for the reconstruction of early hominin behaviors, particularly with regard to the use of perishable tools, which remain archaeologically invisible. © 2017 Wiley Periodicals, Inc.

NASA-JSC Protocol for the Characterization of Single Wall Carbon Nanotube Material Quality

NASA Technical Reports Server (NTRS)

Arepalli, Sivaram; Nikolaev, Pasha; Gorelik, Olga; Hadjiev, Victor; Holmes, William; Devivar, Rodrigo; Files, Bradley; Yowell, Leonard

2010-01-01

It is well known that the raw as well as purified single wall carbon nanotube (SWCNT) material always contain certain amount of impurities of varying composition (mostly metal catalyst and non-tubular carbon). Particular purification method also creates defects and/or functional groups in the SWCNT material and therefore affects the its dispersability in solvents (important to subsequent application development). A number of analytical characterization tools have been used successfully in the past years to assess various properties of nanotube materials, but lack of standards makes it difficult to compare these measurements across the board. In this work we report the protocol developed at NASA-JSC which standardizes measurements using TEM, SEM, TGA, Raman and UV-Vis-NIR absorption techniques. Numerical measures are established for parameters such as metal content, homogeneity, thermal stability and dispersability, to allow easy comparison of SWCNT materials. We will also report on the recent progress in quantitative measurement of non-tubular carbon impurities and a possible purity standard for SWCNT materials.

DC Electric Arc Furnace Application for Production of Nickel-Boron Master Alloys

NASA Astrophysics Data System (ADS)

Alkan, Murat; Tasyürek, Kerem Can; Bugdayci, Mehmet; Turan, Ahmet; Yücel, Onuralp

2017-09-01

In this study, nickel-boron (Ni-B) alloys were produced via a carbothermic reduction starting from boric acid (H3BO3) with high-purity nickel oxide (NiO), charcoal, and wood chips in a direct current arc furnace. In electric arc furnace experiments, different starting mixtures were used, and their effects on the chemical compositions of the final Ni-B alloys were investigated. After the reduction and melting stages, Ni-B alloys were obtained by tapping from the bottom of the furnace. The samples from the designated areas were also taken and analyzed. The chemical composition of the final alloys and selected samples were measured with wet chemical analysis. The Ni-B alloys had a composition of up to 14.82 mass% B. The phase contents of the final alloys and selected samples were measured using x-ray diffraction (XRD). The XRD data helped predict possible reactions and reaction mechanisms. The material and energy balance calculations were made via the XRD Rietveld and chemical compositions. Nickel boride phases started to form 600 mm below the surface. The targeted NiB phase was detected at the tapping zone of the crucible (850-900 mm depth). The energy consumption was 1.84-4.29 kWh/kg, and the electrode consumption was 10-12 g/kg of raw material charged.

Optimisation of mechanical properties of bamboo fibre reinforced-PLA biocomposites

NASA Astrophysics Data System (ADS)

Nurnadia M., J.; Fazita, M. R. Nurul; Abdul Khalil H. P., S.; Mohamad Haafiz M., K.

2017-12-01

The majority of the raw materials that have been widely used in industries are petroleum-based. Growing environmental awareness, the depletion of fossil fuels, and climate change are the key drivers to seek more ecologically friendly materials, such as natural fibres to replace synthetic fibres in polymeric composite. Among the natural fibres available, bamboo fibre has relatively high strength. Poly (lactic) acid (PLA), one of the well-known biopolymers, has been used as a matrix in order to produce totally biodegradable biocomposites. In this study, bamboo fibres were compounded with PLA by a twin screw extruder. The bamboo fibre reinforced PLA composites were then manufactured via the compression moulding method. The influences of screw speed and die temperature during extrusion on the mechanical properties, the tensile and flexural of the biocomposites, were studied. The effects of fibre content and fibre length were also investigated. Taguchi experimental design approach was adopted to determine the optimum set of conditions to achieve the "best" mechanical properties of the composites. Tensile and flexural properties were characterised based on the D638-10 and D790-10 standards, respectively. It was observed that the fibre aspect ratio and fibre content significantly affected the mechanical performance of bamboo fibres reinforced PLA composites.

Raw material variability of an active pharmaceutical ingredient and its relevance for processability in secondary continuous pharmaceutical manufacturing.

PubMed

Stauffer, F; Vanhoorne, V; Pilcer, G; Chavez, P-F; Rome, S; Schubert, M A; Aerts, L; De Beer, T

2018-06-01

Active Pharmaceutical Ingredients (API) raw material variability is not always thoroughly considered during pharmaceutical process development, mainly due to low quantities of drug substance available. However, synthesis, crystallization routes and production sites evolve during product development and product life cycle leading to changes in physical material attributes which can potentially affect their processability. Recent literature highlights the need for a global approach to understand the link between material synthesis, material variability, process and product quality. The study described in this article aims at explaining the raw material variability of an API using extensive material characterization on a restricted number of representative batches using multivariate data analysis. It is part of a larger investigation trying to link the API drug substance manufacturing process, the resulting physical API raw material attributes and the drug product continuous manufacturing process. Eight API batches produced using different synthetic routes, crystallization, drying, delumping processes and processing equipment were characterized, extensively. Seventeen properties from seven characterization techniques were retained for further analysis using Principal Component Analysis (PCA). Three principal components (PCs) were sufficient to explain 92.9% of the API raw material variability. The first PC was related to crystal length, agglomerate size and fraction, flowability and electrostatic charging. The second PC was driven by the span of the particle size distribution and the agglomerates strength. The third PC was related to surface energy. Additionally, the PCA allowed to summarize the API batch-to-batch variability in only three PCs which can be used in future drug product development studies to quantitatively evaluate the impact of the API raw material variability upon the drug product process. The approach described in this article could be applied to any other compound which is prone to batch-to-batch variability. Copyright © 2018 Elsevier B.V. All rights reserved.

Sustainability evaluation of essential critical raw materials: cobalt, niobium, tungsten and rare earth elements

NASA Astrophysics Data System (ADS)

Tkaczyk, A. H.; Bartl, A.; Amato, A.; Lapkovskis, V.; Petranikova, M.

2018-05-01

The criticality of raw materials has become an important issue in recent years. As the supply of certain raw materials is essential for technologically-advanced economies, the European Commission and other international counterparts have started several initiatives to secure reliable and unhindered access to raw materials. Such efforts include the EU Raw Materials Initiative, European Innovation Partnership on Raw Materials, US Critical Materials Institute, and others. In this paper, the authors present a multi-faceted and multi-national review of the essentials for the critical raw materials (CRMs) Co, Nb, W, and rare earth elements (REEs). The selected CRMs are of specific interest as they are considered relevant for emerging technologies and will thus continue to be of increasing major economic importance. This paper presents a ‘sustainability evaluation’ for each element, including essential data about markets, applications and recycling, and possibilities for substitution have been summarized and analysed. All the presented elements are vital for the advanced materials and processes upon which modern societies rely. These elements exhibit superior importance in ‘green’ applications and products subject to severe conditions. The annual production quantities are quite low compared to common industrial metals. Of the considered CRMs, only Co and REE gross production exceed 100 000 t. At the same time, the prices are quite high, with W and Nb being in the range of 60 USD kg‑1 and some rare earth compounds costing almost 4000 USD kg‑1. Despite valiant effort, in practice some of the considered elements are de facto irreplaceable for many specialized applications, at today’s technological level. Often, substitution causes a significant loss of quality and performance. Furthermore, possible candidates for substitution may be critical themselves or available in considerably low quantities. It can be concluded that one preferred approach for the investigated elements could be the use of secondary resources derived from recycling. W exhibits the highest recycling rate (37%), whereas Co (16%), Nb (11%) and rare earths (~0%) lag behind. In order to promote recycling of these essential elements, financial incentives as well as an improvement of recycling technologies would be required.

Incentivizing secondary raw material markets for sustainable waste management.

PubMed

Schreck, Maximilian; Wagner, Jeffrey

2017-09-01

Notwithstanding several policy initiatives in many countries over a number of years, there remains a general sense that too much municipal solid waste is generated and that too much of the waste that is generated is landfilled. There is an emerging consensus that a sustainable approach to waste management requires further development of secondary raw material markets. The purpose of this paper is to propose a theoretical economic model that focuses upon this stage of a sustainable waste management program and explores policy options that could motivate efficiency in secondary raw material markets. In particular, we show how firm profit and social welfare optimizing objectives can be reconciled in a two-product market of waste management processes: landfilling and material reclamation. Our results provide theoretical support for building out recent Circular Economy initiatives as well as for the relatively recent emergence of landfill mining as a means for procuring secondary raw materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

31 CFR 538.410 - Imports of Sudanese goods from third countries; transshipments.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; transshipments. (a) Importation into the United States from third countries of goods containing raw materials or components of Sudanese origin is not prohibited if those raw materials or components have been incorporated...

78 FR 69132 - Importer of Controlled Substances; Notice of Registration; Noramco, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-18

... on applications to import narcotic raw material are not appropriate. 72 FR 3417(2007). In reference to the non-narcotic raw material, any bulk manufacturer who is presently, or is applying to be...

31 CFR 538.410 - Imports of Sudanese goods from third countries; transshipments.

Code of Federal Regulations, 2011 CFR

2011-07-01

...; transshipments. (a) Importation into the United States from third countries of goods containing raw materials or components of Sudanese origin is not prohibited if those raw materials or components have been incorporated...

78 FR 51747 - Importer of Controlled Substances; Notice of Application; NORAMCO, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

... on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007). In reference to the non-narcotic raw material, any bulk manufacturer who is presently, or is applying to be...

The U.S. Chemical Industry, the Raw Materials It Uses

ERIC Educational Resources Information Center

Chemical and Engineering News, 1972

1972-01-01

The raw materials used by the industry are considered in this section of the annual chemical industry report, including data covering: natural gas, lead, mercury, phosphate rock, potash, salt, petroleum products including petrochemical feedstocks. (PR)

Cellulose acetate fibers prepared from different raw materials with rapid synthesis method.

PubMed

Chen, Jinghuan; Xu, Jikun; Wang, Kun; Cao, Xuefei; Sun, Runcang

2016-02-10

Transesterification is a mild process to prepare cellulose acetate (CA) as compared with the traditional method. In this study, CA fibers were produced from six cellulose raw materials based on a simple and rapid transesterification method. The properties of the CA solutions and the obtained CA fibers were investigated in detail. Results showed that all of the cellulose raw materials were esterified within 15 min, and spinning dopes could be obtained by concentrating the CA solutions via vacuum distillation. The XRD, FT-IR, (1)H, (13)C and HSQC NMR analysis confirmed the successful synthesis of CA. The degree of substitution (DS) of the obtained CA was significantly affected by the degree of polymerization (DP) of cellulose raw materials, which further influenced the viscosity of CA solutions as well as the structural, thermal and mechanical properties of the CA fibers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Method of fabricating a honeycomb structure

DOEpatents

Holleran, Louis M.; Lipp, G. Daniel

1999-01-01

A method of fabricating a monolithic honeycomb structure product involves shaping a first mixture of raw materials and a binder into a green honeycomb, extruding a second mixture of raw materials and a binder into one or more green members that each define an opening extending longitudinally therethrough. The raw materials of the second mixture are compatible with the raw materials of the first mixture. The green honeycomb and member(s) are dried. The binders of the green honeycomb and member(s) are softened at the surfaces that are to be bonded. The green member(s) is inserted into the honeycomb and bonded to the honeycomb to form an assembly thereof, which is then dried and fired to form a unified monolithic honeycomb structure. The insertion is best carried out by mounting a member in the shape of a tube on a mandrel, and inserting the mandrel into the honeycomb opening to bond the tube to the honeycomb.

Method of fabricating a honeycomb structure

DOEpatents

Holleran, L.M.; Lipp, G.D.

1999-08-03

A method of fabricating a monolithic honeycomb structure product involves shaping a first mixture of raw materials and a binder into a green honeycomb, extruding a second mixture of raw materials and a binder into one or more green members that each define an opening extending longitudinally therethrough. The raw materials of the second mixture are compatible with the raw materials of the first mixture. The green honeycomb and member(s) are dried. The binders of the green honeycomb and member(s) are softened at the surfaces that are to be bonded. The green member(s) is inserted into the honeycomb and bonded to the honeycomb to form an assembly thereof, which is then dried and fired to form a unified monolithic honeycomb structure. The insertion is best carried out by mounting a member in the shape of a tube on a mandrel, and inserting the mandrel into the honeycomb opening to bond the tube to the honeycomb. 7 figs.

40 CFR 63.1345 - Emissions limits for affected sources other than kilns; in-line kiln/raw mills; clinker coolers...

Code of Federal Regulations, 2011 CFR

2011-07-01

... other than kilns; in-line kiln/raw mills; clinker coolers; new and reconstructed raw material dryers; and raw and finish mills, and open clinker piles. 63.1345 Section 63.1345 Protection of Environment... for affected sources other than kilns; in-line kiln/raw mills; clinker coolers; new and reconstructed...

Development of Product Availability Monitoring System In Production Unit In Automotive Component Industry

NASA Astrophysics Data System (ADS)

Hartono, Rachmad; Raharno, Sri; Yuwana Martawirya, Yatna; Arthaya, Bagus

2018-03-01

This paper described a methodology to monitor the availability of products in a production unit in the automotive component industry. Automotive components made are automotive components made through sheet metal working. Raw material coming into production unit in the form of pieces of plates that have a certain size. Raw materials that come stored in the warehouse. Data of raw each material in the warehouse are recorded and stored in a data base system. The material will then undergo several production processes in the production unit. When the material is taken from the warehouse, material data are also recorded and stored in a data base. The data recorded are the amount of material, material type, and date when the material is out of the warehouse. The material coming out of the warehouse is labeled with information related to the production processes that the material must pass. Material out of the warehouse is a product will be made. The products have been completed, are stored in the warehouse products. When the product is entered into the product warehouse, product data is also recorded by scanning the barcode contained on the label. By recording the condition of the product at each stage of production, we can know the availability of the product in a production unit in the form of a raw material, the product being processed and the finished product.

Artificial lightweight aggregates as utilization for future ashes - A case study.

PubMed

Sarabèr, Angelo; Overhof, Robert; Green, Terry; Pels, Jan

2012-01-01

In the future, more electricity in the Netherlands will be produced using coal with co-combustion. Due to this, the generated annual ash volume will increase and the chemical composition will be influenced. One of the options for utilization if present markets are saturated and for use of fly ashes with different compositions, is as raw material for lightweight aggregates. This was selected as one of the best utilizations options regarding potential ash volume to be applied, environmental aspects and status of technology. Because of this, a study has been performed to assess the potential utilization of fly ash for the production of lightweight aggregate. Lightweight aggregate has been produced in a laboratory scale rotary kiln. The raw material consisted of class F fly ash with high free lime content. An addition of 8% clay was necessary to get green pellets with sufficient green strength. The basic properties of the produced lightweight aggregate and its behaviour in concrete have been investigated. The concrete has a good compressive strength and its leaching behaviour meets the most stringent requirements of Dutch environmental regulations. The carbon foot print of concrete will be negatively influenced if only the concrete itself is taken into account, but the reduction of the volume weight has advantages regarding design, transport emissions and isolation properties which may counteract this. In the Dutch situation the operational costs are higher than expected potential selling price for the LWA, which implies that the gate fee for the fly ash is negative. Copyright © 2011 Elsevier Ltd. All rights reserved.

Changes in the Microbial Composition of Microbrewed Beer during the Process in the Actual Manufacturing Line.

PubMed

Kim, S A; Jeon, S H; Kim, N H; Kim, H W; Lee, N Y; Cho, T J; Jung, Y M; Lee, S H; Hwang, I G; Rhee, M S

2015-12-01

This study investigated changes in the microbial composition of microbrewed beer during the manufacturing processes and identified potential microbial hazards, effective critical quality control points, and potential contamination routes. Comprehensive quantitative (aerobic plate count, lactic acid bacteria, fungi, acetic acid bacteria, coliforms, and Bacillus cereus) and qualitative (Escherichia coli and eight foodborne pathogens) microbiological analyses were performed using samples of raw materials (malt and manufacturing water), semiprocessed products (saccharified wort, boiled wort, and samples taken during the fermentation and maturation process), and the final product obtained from three plants. The initial aerobic plate count and lactic acid bacteria counts in malt were 5.2 and 4.3 log CFU/g, respectively. These counts were reduced to undetectable levels by boiling but were present at 2.9 and 0.9 log CFU/ml in the final product. Fungi were initially present at 3.6 log CFU/g, although again, the microbes were eliminated by boiling; however, the level in the final product was 4.6 log CFU/ml. No E. coli or foodborne pathogens (except B. cereus) were detected. B. cereus was detected at all stages, although it was not present in the water or boiled wort (total detection rate ¼ 16.4%). Results suggest that boiling of the wort is an effective microbial control measure, but careful management of raw materials and implementation of effective control measures after boiling are needed to prevent contamination of the product after the boiling step. The results of this study may constitute useful and comprehensive information regarding the microbiological quality of microbrewed beer.

Needs assessment for nondestructive testing and materials characterization for improved reliability in structural ceramics for heat engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, D.R.; McClung, R.W.; Janney, M.A.

1987-08-01

A needs assessment was performed for nondestructive testing and materials characterization to achieve improved reliability in ceramic materials for heat engine applications. Raw materials, green state bodies, and sintered ceramics were considered. The overall approach taken to improve reliability of structural ceramics requires key inspections throughout the fabrication flowsheet, including raw materials, greed state, and dense parts. The applications of nondestructive inspection and characterization techniques to ceramic powders and other raw materials, green ceramics, and sintered ceramics are discussed. The current state of inspection technology is reviewed for all identified attributes and stages of a generalized flowsheet for advanced structuralmore » ceramics, and research and development requirements are identified and listed in priority order. 164 refs., 3 figs.« less

75 FR 65658 - Importer of Controlled Substances; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-26

... Raw Opium (9600) II Concentrate of Poppy Straw (9670) II The company plans to import narcotic raw... a manufacturer of several controlled substances that are manufactured from raw opium, poppy straw... narcotic raw material are not appropriate. As noted in a previous notice published in the Federal Register...

7 CFR 58.519 - Dairy products.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.519 Dairy products. (a) Raw skim milk. All raw skim milk obtained from a secondary source... used, shall be prepared from raw milk or skim milk that meets the same quality requirements outlined...

Hardwood pallet cant quality and pallet part yields

Treesearch

Hal L. Mitchell; Marshall White; Philip Araman; Peter Hamner

2005-01-01

Raw materials are the largest cost component in pallet manufacturing. The primary raw material used to produce pallet parts are pallet cants. Therefore, pallet cant quality directly impacts pallet part processing and material costs. By knowing the quality of the cants being processed, pallet manufacturers can predict these costs and improve manufacturing efficiency....

Preparation of High-Quality FeV55N Using Ammonia as a Reductant and Nitrogen Source

NASA Astrophysics Data System (ADS)

Wu, Yue-Dong; Zhang, Guo-Hua; Chou, Kuo-Chih

2018-05-01

High-quality FeV55N has been prepared by using ammonia as a reductant and nitrogen source. The raw materials comprised ammonium vanadate and Fe2O3, which were first reduced and nitrided by ammonia to prepare FeV55N composite powders of VN and Fe2N. Subsequently, the composite powders were sintered at high temperature to obtain a bulk FeV55N alloy. The final products obtained by this method do not contain elemental Al, Si, or C impurities. Furthermore, the residual oxygen content of the final products can be reduced to 0.56 wt.%. After sintering, it is possible to obtain a FeV55N alloy with a density of up to 5.4 g/cm3.

Manufacturing and actuation characterization of ionic polymer metal composites with silver as electrodes

NASA Astrophysics Data System (ADS)

Pandita, Surya D.; Lim, Hyoung Tae; Yoo, Youngtai; Park, Hoon Cheol

2006-03-01

Manufacturing and characterization of ionic polymer metal composites (IPMCs) with silver as electrodes have been investigated. Tollen's reagent that contains ion Ag(NH 3) II + was used as a raw material for silver deposition on the surfaces of the polymer membrane Nafion"R". Two types of inner solvents, namely common water based electrolyte solution (LiOH 1N) and ionic liquid were used and investigated. Compared to IPMCs with platinum electrodes, silver-plated IPMCs with water electrolyte showed higher conductivity. The actuation response of silver-plated IPMCs with the water based electrolyte was faster than that of platinum IPMCs. However, the silver electrode was too brittle and severely damaged during the solvent exchange process from water to ionic liquid, resulted in high resistance and hence very low actuation behavior.

77 FR 73426 - Glycine From the People's Republic of China: Final Partial Affirmative Determination of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-10

... the Order because it is producing glycine from raw materials of Indian origin and exporting such... Order because it produced glycine from raw materials of Indian origin and exported such merchandise to...

Effect of Fe(II)/Ce(III) dosage ratio on the structure and anion adsorptive removal of hydrothermally precipitated composites: Insights from EXAFS/XANES, XRD and FTIR.

PubMed

Chubar, Natalia; Gerda, Vasyl; Banerjee, Dipanjan; Yablokova, Ganna

2017-02-01

In this work, we present material chemistry in the hydrothermal synthesis of new complex structure materials based on various dosage ratios of Fe and Ce (1:0, 2:1, 1:1, 1:2, 0:1), characterize them by the relevant methods that allow characterization of both crystalline and amorphous phases and correlate their structure/surface properties with the adsorptive performance of the five toxic anions. The applied synthesis conditions resulted in the formation of different compounds of Fe and Ce components. The Fe-component was dominated by various phases of Fe hydrous oxides, whereas the Ce-component was composed of various phases of Ce carbonates. The presence of two metal salts in raw materials resulted in the formation of a mesoporous structure and averaged the surface area compared to one metal-based material. The surface of all Fe-Ce composites was abundant in Fe component phases. Two-metal systems showed stronger anion removal performance than one-metal materials. The best adsorption was demonstrated by Fe-Ce based materials that had low crystallinity, that were rich in phases and that exhibited surfaces were abundant in greater number of surface functional groups. Notably, Fe extended fine structures simulated by EXAFS in these better adsorbents were rich from oscillations from both heavy and light atoms. This work provides new insights on the structure of composite inorganic materials useful to develop their applications in adsorption and catalysis. It also presents new inorganic anion exchangers with very high removal potential to fluoride and arsenate. Copyright © 2016 Elsevier Inc. All rights reserved.

Innovative use of wood-plastic-composites (WPC) as a core material in the sandwich injection molding process

NASA Astrophysics Data System (ADS)

Moritzer, Elmar; Martin, Yannick

2016-03-01

The demand for materials based on renewable raw materials has risen steadily in recent years. With society's increasing interest for climate protection and sustainability, natural-based materials such as wood-plastic-composites (WPC) have gained market share thanks to their positive reputation. Due to advantages over unreinforced plastics such as cost reduction and weight savings it is possible to use WPC in a wide area of application. Additionally, an increase in mechanical properties such as rigidity and strength is achieved by the fibers compared to unreinforced polymers. The combination of plastic and wood combines the positive properties of both components in an innovative material. Despite the many positive properties of wood-plastic-composite, there are also negative characteristics that prevent the use of WPC in many product areas, such as automotive interiors. In particular, increased water intake, which may result in swelling of near-surface particles, increased odor emissions, poor surface textures and distortion of the components are unacceptable for many applications. The sandwich injection molding process can improve this situation by eliminating the negative properties of WPC by enclosing it with a pure polymer. In this case, a layered structure of skin and core material is produced, wherein the core component is completely enclosed by the skin component. The suitability of WPC as the core component in the sandwich injection molding has not yet been investigated. In this study the possibilities and limitations of the use of WPC are presented. The consideration of different fiber types, fiber contents, skin materials and its effect on the filling behavior are the focus of the presented analysis.

Strain analysis of nanowire interfaces in multiscale composites

NASA Astrophysics Data System (ADS)

Malakooti, Mohammad H.; Zhou, Zhi; Spears, John H.; Shankwitz, Timothy J.; Sodano, Henry A.

2016-04-01

Recently, the reinforcement-matrix interface of fiber reinforced polymers has been modified through grafting nanostructures - particularly carbon nanotubes and ZnO nanowires - on to the fiber surface. This type of interface engineering has made a great impact on the development of multiscale composites that have high stiffness, interfacial strength, toughness, and vibrational damping - qualities that are mutually exclusive to a degree in most raw materials. Although the efficacy of such nanostructured interfaces has been established, the reinforcement mechanisms of these multiscale composites have not been explored. Here, strain transfer across a nanowire interphase is studied in order to gain a heightened understanding of the working principles of physical interface modification and the formation of a functional gradient. This problem is studied using a functionally graded piezoelectric interface composed of vertically aligned lead zirconate titanate nanowires, as their piezoelectric properties can be utilized to precisely control the strain on one side of the interface. The displacement and strain across the nanowire interface is captured using digital image correlation. It is demonstrated that the material gradient created through nanowires cause a smooth strain transfer from reinforcement phase into matrix phase that eliminates the stress concentration between these phases, which have highly mismatched elasticity.

[Denitrification water treatment with zeolite composite filter by intermittent operation].

PubMed

Qing, Cheng-Song; Bao, Tao; Chen, Tian-Hu; Chen, Dong; Xie, Jing-Jing

2012-12-01

The zeolite composite filters (ZCF) with the size of4-8 mm were prepared using raw zeolite (0.15-0.18 mm) as the main material and the cement as binder. After a combination of material characterizations, such as the void fraction, apparent density, compression strength and surface area, the optimal prepared conditions of composite filters were obtained as follow: weight ratio of m (zeolite): m (cement) = 7 : 3, curing for 15 d under the moisture condition and ambient temperature. Through upflow low-concentration ammonia nitrogen wastewater, ZCF filled in the experimental column was hung with the biological membrane. Thus, intermittent dynamic experiments were conducted, the intermittent operation cycle included adsorption, biological regeneration and drip washing. Until concentration of ammonia nitrogen was more than 2 mg x L(-1) of effluent standards, water in experiment column was firstly emptied, and then blast biological regeneration was conducted. After the filters were bathed with water, the zeolite adsorption-biological regeneration cycle was performed repeatedly. The experimental results show that under conditions of 24 h blast and 5 d of continuous operation period, ammonia nitrogen removal rate is up to 87.6% on average, total nitrogen removal rate reaches 51.2% on average.

Numerical Simulation of Thermal Performance of Glass-Fibre-Reinforced Polymer

NASA Astrophysics Data System (ADS)

Zhao, Yuchao; Jiang, Xu; Zhang, Qilin; Wang, Qi

2017-10-01

Glass-Fibre-Reinforced Polymer (GFRP), as a developing construction material, has a rapidly increasing application in civil engineering especially bridge engineering area these years, mainly used as decorating materials and reinforcing bars for now. Compared with traditional construction material, these kinds of composite material have obvious advantages such as high strength, low density, resistance to corrosion and ease of processing. There are different processing methods to form members, such as pultrusion and resin transfer moulding (RTM) methods, which process into desired shape directly through raw material; meanwhile, GFRP, as a polymer composite, possesses several particular physical and mechanical properties, and the thermal property is one of them. The matrix material, polymer, performs special after heated and endue these composite material a potential hot processing property, but also a poor fire resistance. This paper focuses on thermal performance of GFRP as panels and corresponding researches are conducted. First, dynamic thermomechanical analysis (DMA) experiment is conducted to obtain the glass transition temperature (Tg) of the object GFRP, and the curve of bending elastic modulus with temperature is calculated according to the experimental data. Then compute and estimate the values of other various thermal parameters through DMA experiment and other literatures, and conduct numerical simulation under two condition respectively: (1) the heat transfer process of GFRP panel in which the panel would be heated directly on the surface above Tg, and the hot processing under this temperature field; (2) physical and mechanical performance of GFRP panel under fire condition. Condition (1) is mainly used to guide the development of high temperature processing equipment, and condition (2) indicates that GFRP’s performance under fire is unsatisfactory, measures must be taken when being adopted. Since composite materials’ properties differ from each other and their high temperature parameters can’t be obtained through common methods, some parameters are estimated, the simulation is to guide the actual high temperature experiment, and the parameters will also be adjusted by then.

Critical thinking: assessing the risks to the future security of supply of critical metals

NASA Astrophysics Data System (ADS)

Gunn, Gus

2015-04-01

Increasing world population, the spread of prosperity across the globe and the demands of new technologies have led to a revival of concerns about the availability of raw materials needed by society. Despite scare stories about resource depletion, physical exhaustion of minerals is considered to be unlikely. However, we do need to know which materials might be of concern so that we can develop strategies to secure adequate supplies and to mitigate the effects of supply disruption. This requirement has led to renewed interest in criticality, a term that is generally used to refer to metals and minerals of high economic importance that have a relatively high likelihood of supply disruption. The European Union (EU) developed a quantitative methodology for the assessment of criticality which led to the definition of 14 raw materials as critical to the EU economy (EC, 2010). This has succeeded in raising awareness of potential supply issues and in helping to prioritise requirements for new policies and supporting research. The EU has recently assessed a larger number of candidate materials of which 20 are now identified as critical to the EU (EC, 2014). These include metals such as indium, mostly used in flat-screen displays, antimony for flame retardants and cobalt for rechargeable batteries, alloys and a host of other products. Although there is no consensus on the methodology for criticality assessments and broad analyses at this scale are inevitably imperfect, they can, nevertheless, provide early warning of supply problems. However, in order to develop more rigorous and dynamic assessments of future availability detailed analysis of the whole life-cycle of individual metals to identify specific problems and develop appropriate solutions is required. New policies, such as the Raw Materials Initiative (2008) and the European Innovation Partnership on Raw Materials (2013), have been developed by the European Commission (EC) and are aimed at securing sustainable supplies of raw materials. These have led to major new programmes of research throughout the minerals value chain, in order to improve the raw materials knowledge base, to develop best practices and promote international collaboration. Although recycling will make an increasingly important contribution to supply, it can never meet the total requirement when demand is increasing. Therefore, new resources of primary materials, identified through geological research, will continue to be required. The availability of regional baseline datasets, comprising geological, geophysical and geochemical data, is fundamental to the identification of exploration targets. However, in order to focus exploration we also require robust mineral deposit models for the critical metals which hitherto these have been largely neglected because of their limited economic importance. For commodities such as the platinum-group metals (PGM), cobalt, niobium, indium, rare earth elements (REE) and cobalt we have some knowledge of the processes controlling their mobilisation and concentration under certain conditions although we have little understanding of the mechanisms of deposit formation elsewhere. We also need effective techniques to explore for these metals. This may involve the development of new geophysical techniques to explore on the sea-floor or beneath thick cover, or new analytical methods for the determination of these elements in exploration samples. Improved metallurgical techniques are also required for effective and energy-efficient recovery of critical metals from ores and concentrates. References European Commission (2010). Critical raw materials for the EU. Report of the Ad-hoc Working Group on Defining Critical Raw Materials. European Commission (2014). Report on Critical raw materials for the EU. Report of the Ad-hoc Working Group on Defining Critical Raw Materials.

Synthesis and characterisation of composite based biohydroxyapatite bovine bone mandible waste (BHAp) doped with 10 wt % amorphous SiO{sub 2} from rice husk by solid state reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Asmi, Dwi, E-mail: dwiasmi82@yahoo.com, E-mail: dwi.asmi@fmipa.unila.ac.id; Sulaiman, Ahmad, E-mail: ahmadsulaiman@yahoo.co.id; Oktavia, Irene Lucky, E-mail: ireneluckyo@gmail.com

Effect of 10 wt% amorphous SiO{sub 2} from rice husk addition on the microstructures of biohydroxyapatite (BHAp) obtained from bovine bone was synthesized by solid state reaction. In this study, biohydroxyapatite powder was obtained from bovine bone mandible waste heat treated at 800 °C for 5 h and amorphous SiO{sub 2} powder was extracted from citric acid leaching of rice husk followed by combustion at 700°C for 5 h. The composite powder then mixed and sintered at 1200 °C for 3 h. X-ray diffraction (XRD), Fourier transformed infrared (FTIR) spectroscopy and Scanning electron microscopy (SEM) techniques are utilized to characterize the phase relations,more » functional group present and morphology of the sample. The study has revealed that the processing procedures played an important role in microstructural development of BHAp-10 wt% SiO{sub 2} composite. The XRD study of the raw material revealed that the primary phase material in the heat treated of bovine bone mandible waste is hydroxyapatite and in the combustion of rice husk is amorphous SiO{sub 2}. However, in the composite the hydroxyapatite, β-tricalcium phosphate, and calcium phosphate silicate were observed. The FTIR result show that the hydroxyl stretching band in the composite decrease compared with those of hydroxyapatite spectra and the evolution of morphology was occurred in the composite.« less

Synthesis and characterisation of composite based biohydroxyapatite bovine bone mandible waste (BHAp) doped with 10 wt % amorphous SiO2 from rice husk by solid state reaction

NASA Astrophysics Data System (ADS)

Asmi, Dwi; Sulaiman, Ahmad; Oktavia, Irene Lucky; Badaruddin, Muhammad; Zulfia, Anne

2016-04-01

Effect of 10 wt% amorphous SiO2 from rice husk addition on the microstructures of biohydroxyapatite (BHAp) obtained from bovine bone was synthesized by solid state reaction. In this study, biohydroxyapatite powder was obtained from bovine bone mandible waste heat treated at 800 °C for 5 h and amorphous SiO2 powder was extracted from citric acid leaching of rice husk followed by combustion at 700°C for 5 h. The composite powder then mixed and sintered at 1200 °C for 3 h. X-ray diffraction (XRD), Fourier transformed infrared (FTIR) spectroscopy and Scanning electron microscopy (SEM) techniques are utilized to characterize the phase relations, functional group present and morphology of the sample. The study has revealed that the processing procedures played an important role in microstructural development of BHAp-10 wt% SiO2 composite. The XRD study of the raw material revealed that the primary phase material in the heat treated of bovine bone mandible waste is hydroxyapatite and in the combustion of rice husk is amorphous SiO2. However, in the composite the hydroxyapatite, β-tricalcium phosphate, and calcium phosphate silicate were observed. The FTIR result show that the hydroxyl stretching band in the composite decrease compared with those of hydroxyapatite spectra and the evolution of morphology was occurred in the composite.

Design of Chitosan-Grafted Carbon Nanotubes: Evaluation of How the –OH Functional Group Affects Cs+ Adsorption

PubMed Central

Yang, Shubin; Shao, Dadong; Wang, Xiangke; Hou, Guangshun; Nagatsu, Masaaki; Tan, Xiaoli; Ren, Xuemei; Yu, Jitao

2015-01-01

In order to explore the effect of –OH functional groups in Cs+ adsorption, we herein used the low temperature plasma-induced grafting method to graft chitosan onto carbon nanotubes (denoted as CTS-g-CNTs), as raw-CNTs have few functional groups and chitosan has a large number of –OH functional groups. The synthesized CTS-g-CNT composites were characterized using different techniques. The effect of –OH functional groups in the Cs+ adsorption process was evaluated by comparison of the adsorption properties of raw-CNTs with and without grafting chitosan. The variation of environmental conditions such as pH and contact time was investigated. A comparison of contaminated seawater and simulated groundwater was also evaluated. The results indicated that: (1) the adsorption of Cs+ ions was strongly dependent on pH and the competitive cations; (2) for CNT-based material, the –OH functional groups have a positive effect on Cs+ removal; (3) simulated contaminated groundwater can be used to model contaminated seawater to evaluate the adsorption property of CNTs-based material. These results showed direct observational evidence on the effect of –OH functional groups for Cs+ adsorption. Our findings are important in providing future directions to design and to choose effective material to remedy the removal of radioactive cesium from contaminated groundwater and seawater, crucial for public health and the human social environment. PMID:26006711

DPPH Radical Scavenging and Postprandial Hyperglycemia Inhibition Activities and Flavonoid Composition Analysis of Hawk Tea by UPLC-DAD and UPLC-Q/TOF MSE.

PubMed

Xiao, Xuan; Xu, Lijia; Hu, Huagang; Yang, Yinjun; Zhang, Xinyao; Peng, Yong; Xiao, Peigen

2017-10-13

Hawk tea ( Litsea coreana Lévl. var. Lanuginosa (Migo) Yen C. Yang & P.H. Huang), a very popular herbal tea material, has attracted more and more attention due to its high antioxidant properties and possible therapeutic effect on type II diabetes mellitus. The raw materials of Hawk tea are usually divided into three kinds: bud tea (BT), primary leaf tea (PLT) and mature leaf tea (MLT). In this study, the DPPH radical scavenging activity and the antimicrobial properties of these three kinds of Hawk tea from different regions were comparatively investigated, and a ultra-high performance liquid chromatographic coupled with a photodiode array detector (UPLC-DAD) method was employed for comparison of the three major flavonoid constituents, including hyperoside, isoquercitrin and astragalin, in different samples of Hawk tea. At the same time, the effect of methanol extract (ME) of PLT on the mouse postprandial blood glucose and the effect of ME and its different fractions (petroleum ether fraction (PE), ethyl acetate fraction (EA), n -butanol fraction ( n -BuOH), and water fraction (WF)) on the activity of α-glucosidase were studied. The results showed that Hawk BT and Hawk PLT possessed the higher radicals scavenging activity than Hawk MLT, while the antibacterial activity against P. vulgaris of PLT and MLT was higher than Hawk BT. The contents of the three major flavonoid constituents in samples of Hawk PLT are higher than Hawk BT and Hawk MLT. The mouse postprandial blood glucose levels of the middle dose (0.5 g/kg) group and the high dose (1 g/kg) group with oral administration of the ME of PLT were significantly lower than the control group. What's more, the inhibitory effect of ME of PLT and its EA and n -BuOH fractions on α-glucosidase was significantly higher than that of acarbose. Rapid ultra-high performance liquid chromatography/quadrupole time-of-flight-mass spectrometry (UPLC-ESI-QTOF-MS) was used to identify the flavonoids in Hawk PLT, and a total of 20 flavonoids were identified or tentatively identified by comparing their retention times and accurate mass measurements with reference compounds or literature data. The bioactive flavonoid composition and DPPH radical scavenging activities present in different Hawk tea raw materials are quite different due to the different ontogenesis of these raw materials. Further studies on PLT showed that the substances in PLT ME could reduce the level of mouse postprandial blood glucose through inhibiting the activity of α-glucosidase.

77 FR 34069 - Importer of Controlled Substances; Notice of Application; Research Triangle Institute

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-08

... activities. Comments and requests for hearings on applications to import narcotic raw material are not appropriate. 72 FR 3417 (2007). In regard to the non-narcotic raw material, any bulk manufacturer who is... [[Page 34072

Evaluation of physicochemical properties as supporting information on quality control of raw materials and veterinary pharmaceutical formulations.

PubMed

Anacleto, Sara da Silva; Borges, Marcella Matos Cordeiro; de Oliveira, Hanna Leijoto; Vicente, Andressa Reis; de Figueiredo, Eduardo Costa; de Oliveira, Marcone Augusto Leal; Borges, Bárbara Juliana Pinheiro; de Oliveira, Marcelo Antonio; Borges, Warley de Souza; Borges, Keyller Bastos

2018-06-01

This study aimed to show that the physicochemical proprieties obtained by Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TG), and scanning electronic microscopy (SEM) can be useful tools for evaluating the quality of active pharmaceutical ingredients (APIs) and pharmaceutical products. In addition, a simple, sensitive, and efficient method employing HPLC-DAD was developed for simultaneous determination of lidocaine (LID), ciprofloxacin (CFX) and enrofloxacin (EFX) in raw materials and in veterinary pharmaceutical formulations. Compounds were separated using a Gemini C 18 (250 mm × 4.6 mm, 5 µm) Phenomenex ® column, at a temperature of 25 °C, with a mobile phase containing 10 mM of phosphoric acid (pH 3.29): acetonitrile (85.7:14.3, v/v) and a flow rate of 1.5 mL/min. Physicochemical characterization by TG, FTIR, and SEM of raw materials of LID, CFX, and EFX provided information useful for the evaluation, differentiation, and qualification of raw materials. Finally, the HPLC method was proved to be useful for evaluation of raw material and finished products, besides satisfying the need for an analytical method that allows simultaneous determination of EFX, CFX, and LID, which can also be extended to other matrices and applications.

Colour of ground beef as influenced by raw materials, addition of sodium chloride and low oxygen packaging.

PubMed

Sørheim, O; Westad, F; Larsen, H; Alvseike, O

2009-03-01

The study aimed at examining the effects of freezing of raw materials, holding time for fresh raw materials post mortem and addition of 0.5-1.0% NaCl on the colour of ground beef under low oxygen (O2) modified atmosphere storage. The samples were exposed to 0.1-3.0% O2 at 4°C for up to 10 days, and analysed for O2 concentrations, instrumental and visual colour. Residual O2 in the headspace of the packages oxidizes myoglobin and discolours the meat. Meat may have the ability to scavenge residual O2, and ground beef differs from intact muscles by having a much higher capacity for O2 consumption. In this experiment, the use of frozen/thawed raw materials and addition of NaCl both decreased the rate of O2 consumption and increased discolouration. Using raw materials from 2 days rather than 7 days post mortem greatly increased the rate of removal of O2 and improved redness. In low O2 packaging, ground beef preferably should be stored for at least 2 days in an atmosphere with less than 0.1% residual O2 to produce a purple pigment predominantly consisting of deoxymyoglobin.

Effects and detection of raw material variability on the performance of near-infrared calibration models for pharmaceutical products.

PubMed

Igne, Benoit; Shi, Zhenqi; Drennen, James K; Anderson, Carl A

2014-02-01

The impact of raw material variability on the prediction ability of a near-infrared calibration model was studied. Calibrations, developed from a quaternary mixture design comprising theophylline anhydrous, lactose monohydrate, microcrystalline cellulose, and soluble starch, were challenged by intentional variation of raw material properties. A design with two theophylline physical forms, three lactose particle sizes, and two starch manufacturers was created to test model robustness. Further challenges to the models were accomplished through environmental conditions. Along with full-spectrum partial least squares (PLS) modeling, variable selection by dynamic backward PLS and genetic algorithms was utilized in an effort to mitigate the effects of raw material variability. In addition to evaluating models based on their prediction statistics, prediction residuals were analyzed by analyses of variance and model diagnostics (Hotelling's T(2) and Q residuals). Full-spectrum models were significantly affected by lactose particle size. Models developed by selecting variables gave lower prediction errors and proved to be a good approach to limit the effect of changing raw material characteristics. Hotelling's T(2) and Q residuals provided valuable information that was not detectable when studying only prediction trends. Diagnostic statistics were demonstrated to be critical in the appropriate interpretation of the prediction of quality parameters. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

Seasonal changes in chemical and mineralogical composition of sewage sludge incineration residues and their potential for metallic elements and valuable components recovery

NASA Astrophysics Data System (ADS)

Kasina, Monika; Kowalski, Piotr R.; Michalik, Marek

2017-04-01

Increasing energy needs, the implementation of the circular economy principles and rising environmental awareness caused that waste management is becoming a major social and economic issue. The EU Member States have committed to a significant reduction in the amount of waste produced and landfilled and to use their inherent energy and raw materials potential. One of the most reasonable option to fulfil these commitments is waste incineration. The aim of the waste incineration is to reduce their volume and toxicity by disinfection and detoxification at high temperatures. Thermal process and reduction of volume allows the recovery of minerals and metallic elements from residues as well as the energy production (waste-to-energy strategy) during incineration. As a result of waste incineration a variety of solid residues (bottom ash, fly ash, air pollution control residues) and technological waste (gas waste, wastewater) are produced. The goal of this study is to characterize fly ash and air pollution control (APC) residues formed as a result of municipal sewage sludge incineration in terms of their chemical and mineral composition and their extractive potential. Residues were sampled quarterly to study their seasonal changes in composition. The fly ash was a Si-P-C-Fe-Al dominated material, whereas the APC residues composition was dominated by Na-rich soluble phases. The removal of soluble phase ( 98% of the material) from the APC residues by dissolution in deionised water caused significant mass reduction and concentration of non-soluble elements. The main mineral phases in fly ash were quartz, hematite, Fe-PO4, whitlockite and feldspar, while in APC thenardite, and in lower amount calcite, apatite and quartz were present. The chemical composition of fly ash was practically invariable in different seasons, but significant differences were observed in APC residues. The lowest concentrations of all elements and the highest TOC content were measured in the samples collected in the spring 2016. The highest concentrations for most of the elements were measured in summer 2016 except for the Ca, Sn, Zn, Cd, Sb, and Ag which concentrations were the highest in the winter time 2015. Even though the seasonal changes in metallic and/or potentially valuable elements concentrations are visible their overall content is low. In addition they are dispersed within crystalline and amorphous phase, therefore it seems to be inappropriate to consider this material as a source of valuable elements. Due to high phosphorus content in the fly ash, equal to the low grade phosphorus ore, both in the form of phosphate minerals as well as dispersed within minerals can be treated as a potential source of this critical raw material. Acknowledgment: The study was supported by Polish National Science Centre. NCN grant No UMO-2014/15/B/ST10/04171

The influence of sugarcane bagasse ash as fly ash on cement quality

NASA Astrophysics Data System (ADS)

Rauf, N.; Damayanti, M. C.; Pratama, S. W. I.

2017-01-01

Fly ash often is used as the third material for cement. The fly ash from sugarcane bagasse is usually considered as industrial waste material that can be added to the base material of cement (clinker, trash, gypsum and lime stone) for economic and environment reason. The amount of fly ash usually up to 30 % of cement material, but in this research the percentage of sugarcane bagasse ash (SBA) is added to cement material is up to 15% total weight. Then the x-rays fluorescence (XRF) was used to determine its chemical composition of raw material and cement samples. The physical properties of cement such as fineness, setting time, expansion, and compressive strength were measured using Automatic Blaine, Vicat, Autoclave, respectively. The result show that the percentage of sugarcane bagasse ash influences the quality of cement and concrete, and this is confirmed with Indonesia National Standard (SNI). It is showed that the sugarcane bagasse ash could be use as material to improve the quality of cement and will solve the environment waste material

A comparative study of green composites based on tapioca starch and celluloses

NASA Astrophysics Data System (ADS)

Owi, Wei Tieng; Lin, Ong Hui; Sam, Sung Ting; Mern, Chin Kwok; Villagracia, Al Rey; Santos, Gil Nonato C.; Akil, Hazizan Md

2017-07-01

The objective of this study was to compare the properties of green composites based on tapioca starch (TS) and celluloses isolated from empty fruit bunches (EFB) and commercial celluloses from cotton linter (supplied by Sigma). Empty fruit bunches (EFB) acted as the main source to obtain the cellulose by using a chemical approach whereas the commercial cellulose from Sigma was used as reference. The TS/cellulose composite films were prepared using cellulose in varying proportions as filler into TS matrix by a casting method. The amount of celluloses added into the tapioca starch were 5, 10, 15, 20 and 25 phr (as per dry mass of TS). The celluloses were characterized using Fourier transform infrared (FTTR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). While the green composite films were analyzed in terms of thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), SEM and tensile properties. FTTR analysis confirmed the removal of non-cellulosic materials such as hemicelluloses and lignin from raw EFB after the chemical treatment. XRD diffractograms revealed that the crystallinity of celluloses EFB increased from 43.1 % of raw EFB to 52.1 %. SEM images showed the fibrillar structure of cellulose isolated from EFB. The TGA and derivative thermogravimetric (DTG) curves of green composite films showed no significant effect on the thermal stability. Melting temperature of TS/cellulose EFB higher than neat TS while TS/cellulose Sigma lower than neat TS. The green composite films with 15 phr cellulose from EFB filler loading provided the best tensile properties in term of its strength and modulus. However, in term of elongation at break, the percentage elongation decreased with the increased of the amount of filler loading. SEM images of the films demonstrated a good interaction between cellulose filler and TS matrix especially with the addition of 15 phr of cellulose from EFB.

Materials, critical materials and clean-energy technologies

NASA Astrophysics Data System (ADS)

Eggert, R.

2017-07-01

Modern engineered materials, components and systems depend on raw materials whose properties provide essential functionality to these technologies. Some of these raw materials are subject to supply-chain risks, and such materials are known as critical materials. This paper reviews corporate, national and world perspectives on material criticality. It then narrows its focus to studies that assess "what is critical" to clean-energy technologies. The focus on supply-chain risks is not meant to be alarmist but rather to encourage attention to monitoring these risks and pursuing technological innovation to mitigate the risks.

Raw liquid waste treatment process

NASA Technical Reports Server (NTRS)

Humphrey, Marshall F. (Inventor)

1980-01-01

A raw sewage treatment process is disclosed in which substantially all the non-dissolved matter, which is suspended in the sewage water is first separated from the water, in which at least organic matter is dissolved. The non-dissolved material is pyrolyzed to form an activated carbon and ash material without the addition of any conditioning agents. The activated carbon and ash material is added to the water from which the non-dissolved matter was removed. The activated carbon and ash material absorbs organic matter and heavy metal ions, it is believed, are dissolved in the water and is thereafter supplied in a counter current flow direction and combined with the incoming raw sewage to facilitate the separation of the non-dissolved settleable materials from the sewage water. The used carbon and ash material together with the non-dissolved matter which was separated from the sewage water are pyrolyzed to form the activated carbon and ash material.

Raw Liquid Waste Treatment System and Process

NASA Technical Reports Server (NTRS)

Humphrey, M. F. (Inventor)

1974-01-01

A raw sewage treatment process is disclosed in which substantially all the non-dissolved matter, suspended in the sewage water is first separated from the water, in which at least organic matter remains dissolved. The non-dissolved material is pyrolyzed to form an activated carbon and ash material without the addition of any conditioning agents. The activated carbon and ash material is added to the water from which the non-dissolved matter was removed. The activated carbon and ash material adsorbs the organic matter dissolved in the water and is thereafter supplied in a counter flow direction and combined with the incoming raw sewage to at least facilitate the separation of the non-dissolved settleable materials from the sewage water. Carbon and ash material together with the non-dissolved matter which was separated from the sewage water are pyrolyzed to form the activated carbon and ash material.

Rye bran as fermentation matrix boosts in situ dextran production by Weissella confusa compared to wheat bran.

PubMed

Kajala, Ilkka; Mäkelä, Jari; Coda, Rossana; Shukla, Shraddha; Shi, Qiao; Maina, Ndegwa Henry; Juvonen, Riikka; Ekholm, Päivi; Goyal, Arun; Tenkanen, Maija; Katina, Kati

2016-04-01

The consumption of fiber-rich foods such as cereal bran is highly recommended due to its beneficial health effects. Pre-fermentation of bran with lactic acid bacteria can be used to improve the otherwise impaired flavor and textural qualities of bran-rich products. These positive effects are attributed to enzymatic modification of bran components and the production of functional metabolites like organic acids and exopolysaccharides such as dextrans. The aim of this study was to investigate dextran production in wheat and rye bran by fermentation with two Weissella confusa strains. Bran raw materials were analyzed for their chemical compositions and mineral content. Microbial growth and acidification kinetics were determined from the fermentations. Both strains produced more dextran in rye bran in which the fermentation-induced acidification was slower and the acidification lag phase longer than in wheat bran. Higher dextran production in rye bran is expected to be due to the longer period of optimal pH for dextran synthesis during fermentation. The starch content of wheat bran was higher, which may promote isomaltooligosaccharide formation at the expense of dextran production. W. confusa Cab3 produced slightly higher amounts of dextran than W. confusa VTT E-90392 in all raw materials. Fermentation with W. confusa Cab3 also resulted in lower residual fructose content which has technological relevance. The results indicate that wheat and particularly rye bran are promising matrices for producing technologically significant amounts of dextran, which facilitates the use of nutritionally valuable raw bran in food applications.

Effect of processing techniques on nutritional composition and antioxidant activity of fenugreek (Trigonella foenum-graecum) seed flour.

PubMed

Pandey, Hemlata; Awasthi, Pratima

2015-02-01

Fenugreek (Pusa Early Bunching) seeds were processed by using different processing methods viz. soaking, germination and roasting. Raw and processed fenugreek seed flours were analyzed for nutritional composition, anti- nutritional, and antioxidant activity. Raw fenugreek seed flour contained higher amount of dietary fiber (45.4 %) followed by 41.7 % in soaked seed flour, 40.9 % in roasted fenugreek seed flour and 31.3 % in germinated fenugreek seed flour. Processing of fenugreek seeds improved in vitro starch digestibility and in vitro protein digestibility. Soaking, germination and roasting enhanced total phenolic content and the antioxidant activity of fenugreek seed flour as compared to raw fenugreek seed flour. The phenolic content of soaked, germinated and roasted fenugreek seed flours was 54.4, 80.8 and 48.5 mg of gallic acid equivalents/g of sample in contrast to raw fenugreek seed flour (45.4 mg of gallic acid equivalents/g of sample). The antioxidant activity of the extracts of soaked, germinated and roasted fenugreek seed flours was 60.7 %, 73.9 % and 32.0 % whereas as the raw fenugreek seed flour exhibited 18.1 % antioxidant activity. Processing of fenugreek seeds also decreased phytic acid content significantly (P < 0.05) as compared to raw seeds.

Comparative studies on the mechanical properties of natural rubber and natural rubber filled with multi-walled carbon nanotubes

NASA Astrophysics Data System (ADS)

Ismail, R.; Ibrahim, A.; Rusop, M.; Adnan, A.

2018-05-01

The present article compares the mechanical properties of natural rubber (NR) and carbon nanotubes (CNTs) filled natural rubber composites. Four types of nanocomposite specimens are fabricated with different MWCNT loadings: 0 wt% (pure natural rubber), 1 wt%, 3 wt%, and 5 wt%. The specimens are tested for their mechanical properties. It is observed that the tensile strength, hardness and elongation break of CNTs filled rubber composites are remarkably higher than that of raw rubber indicating the inherent reinforcing potential of CNTs. Percentage of the elongation at break of rubber CNTs composites is lower than that of raw rubber.

Investigation of tribological properties of biobased polymers and polymeric composites

NASA Astrophysics Data System (ADS)

Bhuyan, Satyam Kumar

Worldwide potential demands for replacing petroleum derived raw materials with renewable plant-based ones in the production of valuable polymeric materials and composites are quite significant from the social and environmental standpoints. Therefore, using low-cost renewable resources has deeply drawn the attention of many researchers. Among them, natural oils are expected to be ideal alternative feedstock since oils, derived from plant and animal sources, are found in profusion in the world. The important feature of these types of materials is that they can be designed and tailored to meet different requirements. The real challenge lies in finding applications which would use sufficiently large quantities of these materials allowing biodegradable polymers to compete economically in the market. Lack of material and tribological characterizations have created an awareness to fulfill this essential objective. In order to understand the viability of biobased polymers in structural applications, this thesis work elucidates the study of friction and wear characteristics of polymers and polymeric composites made out of natural oil available profusely in plants and animals. The natural oils used in this study were soybean and tung oil. Various monomeric components like styrene, divinely benzene etc. were used in the synthesis of biobased polymers through Rh-catalyzed isomerization techniques. For the different polymeric composites, spent germ, a byproduct of ethanol production, is used as the filler and an organoclay called montmorillonite is used as the reinforcing agent in the polymer matrix. The effect of crosslinker concentration, filler composition and reinforcement agent concentration was studied under dry sliding. A ball-on-flat tribometer with a probe made out of steel, silicon nitride or diamond was used for most of the experimental work to measure friction and generate wear. The wear tracks were quantified with an atomic force microscope and a contact profilometer. The wear morphologies were studied with a scanning electron microscope. Thermosetting epoxy resin was used as a benchmark material to compare the tribological characteristics of the biobased polymers. Synthetic polymeric materials made out of norbornene monomers were also subjected to friction and wear tests. An empirical relationship between wear behavior and crosslinking was established.

The determination of optimum condition in water hyacinth drying process by mixed adsorption drying method and modified fly ash as an adsorbent

NASA Astrophysics Data System (ADS)

Saputra, Asep Handaya; Putri, Rizky Anggreini

2017-05-01

Water hyacinth is an aquatic weed that has a very fast growth which makes it becomes a problem to the ecosystem. On the other hand, water hyacinth has a high fiber content (up to 20% by weight) which makes it potential to become raw material for composites and textile industries. As an aquatic plant, water hyacinth has a high initial moisture content that reaches more than 90%. Meanwhile the moisture content of fiber as a raw material for composite and textile industry should not be more than 10% to maintain the good quality of the products. Mixed adsorption drying method is one of the innovative method that can replace conventional drying process. Fluidization method which has been commonly used in agricultural and pharmaceutical products drying, can be enhanced by combining it with the adsorption method as performed in this study. In mixed fluidization-adsorption drying method, fly ash as adsorbent and water hyacinth fiber were put together into the fluidization column where the drying air evaporate the moisture content in water hyacinth fiber. In addition, the adsorbent adsorb the moisture content in the drying air to make the moisture content of the drying air remain low. The drying process is performed in various temperature and composition of water hyacinth and adsorbent in order to obtain the optimum drying condition. In addition, the effect of fly ash pellet and fly ash powder to the drying process was also performed. The result shows that the higher temperature and the more amount of adsorbent results in the faster drying rate. Fly ash pellet shows a better adsorption since it has a smaller pore diameter and wider surface area. The optimum temperature obtained from this study is 60°C and the optimum ratio of water hyacinth and fly ash is 50:50.

Investigation of carbonate rocks appropriate for the production of natural hydraulic lime binders

NASA Astrophysics Data System (ADS)

Triantafyllou, George; Panagopoulos, George; Manoutsoglou, Emmanouil; Christidis, George; Přikryl, Richard

2014-05-01

Cement industry is facing growing challenges in conserving materials and conforming to the demanding environmental standards. Therefore, there is great interest in the development, investigation and use of binders alternatives to Portland cement. Natural hydraulic lime (NHL) binders have become nowadays materials with high added value, due to their advantages in various construction applications. Some of them include compatibility, suitability, workability and the versatility in applications. NHL binders are made from limestones which contain sufficient argillaceous or siliceous components fired at relatively low temperatures, with reduction to powder by slaking with or without grinding. This study is focused in developing technology for small-scale production of cementitious binders, combining the knowledge and experience of geologists and mineral resources engineers. The first step of investigation includes field techniques to the study the lithology, texture and sedimentary structure of Neogene carbonate sediments, from various basins of Crete Island, Greece and the construction of 3D geological models, in order to determine the deposits of each different geological formation. Sampling of appropriate quantity of raw materials is crucial for the investigation. Petrographic studies on the basis of the study of grain type, grain size, types of porosity and depositional texture, are necessary to classify effectively industrial mineral raw materials for this kind of application. Laboratory tests should also include the study of mineralogical and chemical composition of the bulk raw materials, as well as the content of insoluble limestone impurities, thus determining the amount of active clay and silica components required to produce binders of different degree of hydraulicity. Firing of the samples in various temperatures and time conditions, followed by X-ray diffraction analysis and slaking rate tests of the produced binders, is essential to insure the beneficiation of their behavior. Beneficiation is defined as the implementation of the best available techniques to insure the production of an economically usable final product which combines both the hydraulicity of the silicates, aluminates and ferrites, as well as the reactivity of the calcium oxide amounts that are present.

21 CFR 1303.23 - Procedure for fixing individual manufacturing quotas.

Code of Federal Regulations, 2010 CFR

2010-04-01

... economic and physical availability of raw materials for use in manufacturing and for inventory purposes, yield and stability problems, potential disruptions to production (including possible labor strikes... current inventory position, the economic and physical availability of raw materials for use in...

Use of outer planet satellites and asteroids as sources of raw materials for life support systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Molton, P.M.; Divine, T.E.

1977-01-01

Industrialization of space and other space activities depend entirely on supply of materials from the Earth. This is a high cost route for materials supply. Space industrialization will require life support systems for maintenance and operation staff and these will of necessity be of a sophisticated nature. Use of raw materials obtained by an unmanned space shuttle, initially, and by manned shuttles later could significantly reduce the cost of life support in space. These raw materials could be obtained from small asteroids and satellites, and would consist of primary nutrients. Future development of such sources is discussed, including food productionmore » in automated asteroid-based facilities. The level of technology required is available now, and should become economical within a century.« less

Biomass Briquette Investigation from Pterocarpus Indicus Leaves Waste as an Alternative Renewable Energy

NASA Astrophysics Data System (ADS)

Anggono, Willyanto; Sutrisno; Suprianto, Fandi D.; Evander, Jovian

2017-10-01

Indonesia is a tropical country located in Southeast Asia. Indonesia has a lot of variety of plant species which are very useful for life. Pterocarpus indicus are commonly used as greening and easily found everywhere in Surabaya city because of its characteristics that they have dense leaves and rapid growth. Pterocarpus indicus leaves waste would be a problem for residents of Surabaya and disturbing the cleanliness of the Surabaya city. Therefore, the Pterocarpus indicus leaves waste would be used as biomass briquettes. This research investigated the calorific value of biomass briquettes from the Pterocarpus indicus leaves waste, the effect of tapioca as an adhesive material to the calorific value of biomass briquettes from the Pterocarpus indicus leaves waste, the optimum composition for Pterocarpus indicus leaves waste biomass briquette as an alternative renewable fuel and the property of the optimum resulted biomass briquette using ultimate analysis and proximate analysis based on the ASTM standard. The calorific value biomass briquettes from the Pterocarpus indicus leaves waste were performed using an oxygen bomb calorimeter at various composition of Pterocarpus indicus from 50% to 90% rising by 10% for each experiment. The experimental results showed that the 90% raw materials (Pterocarpus indicus leaves waste)-10% adhesive materials (tapioca) mixtures is the optimum composition for biomass briquette Pterocarpus indicus leaves waste. The lower the percentage of the mass of tapioca in the biomass briquettes, the higher calorific value generated.

Eucommia ulmoides Oliver: A Potential Feedstock for Bioactive Products.

PubMed

Zhu, Ming-Qiang; Sun, Run-Cang

2018-06-06

Eucommia ulmoides Oliver (EUO), a traditional Chinese herb, contains a variety of bioactive chemicals, including lignans, iridoids, phenolics, steroids, terpenoids, flavonoids, etc. These bioactive chemicals possess the effective function in nourishing the liver and kidneys and regulating blood pressure. The composition of bioactive chemicals extracted from EUO vary in the different functional parts (leaves, seeds, bark, and staminate flower) and planting models. The bioactive parts of EUO are widely used as raw materials for medicine and food, powdery extracts, herbal formulations, and tinctures. These capabilities hold potential for future development and commercial exploitation of the bioactive products from EUO.

[Determination by high performance chromatography, steroid saponins in a biologically active food supplements containing the extract of Tribulus terrestris].

PubMed

Kozlova, O I; Perederiaev, O I; Ramenskaia, G V

2011-01-01

Steroidal saponins are bioactive substances of Tribulus terrestris and can be used to assess the quality of raw materials and processed products from them. For this purpose has been developed the method of qualitative and quantitative determination of steroidal saponins by high performance liquid chromatography with spectrophotometric and mass-selective detection and optimal conditions of sample preparation (70% methanol extraction with sonication and heating); also has been studied steroidal saponins composition of Tribulus terrestris (protodioscin, tribulosaponin B, metilprotodiostsin, terrestrozin H, prototribestin, gracillin and others were found).

Superconductivity achieved at over liquid nitrogen temperature by (mixed rare earths)-Ba-Cu oxides

NASA Astrophysics Data System (ADS)

Kishio, Kohji; Kuwahara, Kazuyuki; Kitazawa, Koichi; Fueki, Kazuo; Nakamura, Osamu

1987-05-01

Superconducting oxides were fabricated by reaction of powders of BaCO3, CuO and mixed rare earth (RE) carbonates at compositions expressed as (RE)1Ba2Cu3O(9-y). Two types of incompletely separated raw materials of mixed rare earths, namely, heavy rare earths (HRE) and medium rare earths (MRE), were examined. The zero-resistivity critical temperatures were observed at 92.5 K for the (HRE)-Ba-Cu-O and 85.0 K for the (MRE)-Ba-Cu-O systems, respectively, both of which were well above the boiling point of liquid nitrogen.