DETAIL VIEW OF LOWER TRAM TERMINAL, SECONDARY ORE BIN, CRUSHER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF LOWER TRAM TERMINAL, SECONDARY ORE BIN, CRUSHER FOUNDATION, AND BALL MILL FOUNDATIONS, LOOKING NORTH NORTHWEST. ORE FROM THE MINES WAS DUMPED FROM THE TRAM BUCKETS INTO THE PRIMARY ORE BIN UNDER THE TRAM TERMINAL. A SLIDING CONTROL DOOR INTRODUCED THE INTO THE JAW CRUSHER (FOUNDATIONS,CENTER). THE CRUSHED ORE WAS THEN CONVEYED INTO THE SECONDARY ORE BIN AT CENTER LEFT. A HOLE IN THE FLOOR OF THE ORE BIN PASSED ORE ONTO ANOTHER CONVEYOR THAT BROUGHT IT OUT TO THE BALL MILL(FOUNDATIONS,CENTER BOTTOM). THIS SYSTEM IS MOST LIKELY NOT THE ORIGINAL SET UP, PROBABLY INSTALLED IN THE MINE'S LAST OCCUPATION IN THE EARLY 1940s. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

40 CFR 440.140 - Applicability; description of the gold placer mine subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold... gold bearing ores from placer deposits; and (2) The beneficiation processes which use gravity... applicable to any mines or beneficiation processes which process less than 1500 cubic yards (cu yd) of ore...

40 CFR 440.80 - Applicability; description of the vanadium ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... vanadium ore subcategory. 440.80 Section 440.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.80 Applicability; description of the...

40 CFR 440.80 - Applicability; description of the vanadium ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... vanadium ore subcategory. 440.80 Section 440.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.80 Applicability; description of the...

40 CFR 440.80 - Applicability; description of the vanadium ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... vanadium ore subcategory. 440.80 Section 440.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.80 Applicability; description of the...

Preliminary report on the Apex and Paymaster mines, Washington County, Utah

USGS Publications Warehouse

Kinkel, Arthur R.

1951-01-01

The Apex and Paymaster mines in the Tutsagubet mining district, 25 miles southwest of St. George, Utah, are at an elevation of about 5,000 feet in the Beaver Dam Mountains. The ore was deposited in a steeply dipping fault zone which cuts a thick series of gently dipping limestones of Pennsylvanian age with minor interbedded shales and sandstones. The ore now consists primarily of copper oxides, but is reported to contain small quantities of lead and sine oxides. Complete oxidation extends to the 1,400 level of the Apex mine, the deepest level in this mine. Lead oxides are reported to have been more plentiful in the workings near surface, but the stoped area is now caved to the 1,330 level. The ore bodies probably formed largely as a filling in the fault fissure, and in crushed zones along the fault, with only minor replacement extending for short distances along the bedding. The sulfides oxidized essentially in place and migration of the oxidized copper ores is believed to be limited to a few feet. Additional exploration below the known ore shoots in the Apex and Paymaster mines and along the fissure between the two mines may disclose new ore bodies.

78 FR 47317 - Ore Knob Mine Superfund Site; Laurel Springs, Ashe County, North Carolina; Notice of Settlement

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-05

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9843-3; CERCLA-04-2013-3759] Ore Knob Mine Superfund Site; Laurel Springs, Ashe County, North Carolina; Notice of Settlement AGENCY: Environmental Protection Agency... settlement with Herbert N. Francis concerning the Ore Knob Mine Superfund Site located in Laurel Springs...

UNDERGROUND URANIUM MINING ON COLORADO PLATEAU

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dare, W.L.

1958-10-31

The size and continuity of the Chinie ore bodies in the Big Indian district, Utah, have permitted mine operators in plan a more integrated development and mining system using larger and more specialized equipment. Thick ore and firm backs at the south end of the district than permitted room and pillar mining, using large drill jumbos send diesel-powered haulage equipment. The Gismo loader and draw-chute system has proved efficient. Driving the haulage- way below the stope level is an advantage when pillars are recovered. To the north, thinner ore with weaker backs favor retreat systems and smaller equipment. Here, themore » ore bodies are delineated by a grid system of drifts, send the ore recovered by panel, longwall, or similar mining methods, retreating toward the principal entry. Labor productivity ranges from 8 to 21 tons per man-shift, send direct mining send development costs, excluding initial development, ranges from 75 to 51 per ton. A unique system of mine development is in the Temple Mountain district, Utah, where the shallow Chinie deposits are mined through 36- inch diameter calyx drill holes. Using small diesel-powered ore buggies and bucket hoisting, ore in produced from the two largest mines at a rate of 4.1 tons per man-shift, at a direci cost of 15 a ton. Ambrosia Lake deposits range from 5 to 80 feet thick and occur from 350 to 1,000 feet below the surface. These mines are in development stages. Open, retreat, and top-slice sloping is planned. Adequate ventilation is essential in uranium mining since sufficient air must be coursed through the workings to maintain airborne radioactive concentration at tolerance levels send dilute exhaust gases where diesel-powered equipment is used. Uranium miners have found that radiometric scannning is a quick and efficient method for checking ths grade of the ore produced and in process of development. (auth)« less

Isotopic Variability of Mercury in Ore, Mine-Waste Calcine, and Leachates of Mine-Waste Calcine from Areas Mined for Mercury

PubMed Central

2009-01-01

The isotopic composition of mercury (Hg) was determined in cinnabar ore, mine-waste calcine (retorted ore), and leachates obtained from water leaching experiments of calcine from two large Hg mining districts in the U.S. This study is the first to report significant mass-dependent Hg isotopic fractionation between cinnabar ore and resultant calcine. Data indicate that δ202Hg values relative to NIST 3133 of calcine (up to 1.52‰) in the Terlingua district, Texas, are as much as 3.24‰ heavier than cinnabar (−1.72‰) prior to retorting. In addition, δ202Hg values obtained from leachates of Terlingua district calcines are isotopically similar to, or as much as 1.17‰ heavier than associated calcines, most likely due to leaching of soluble, byproduct Hg compounds formed during ore retorting that are a minor component in the calcines. As a result of the large fractionation found between cinnabar and calcine, and because calcine is the dominant source of Hg contamination from the mines studied, δ202Hg values of calcine may be more environmentally important in these mined areas than the primary cinnabar ore. Measurement of the Hg isotopic composition of calcine is necessary when using Hg isotopes for tracing Hg sources from areas mined for Hg, especially mine water runoff. PMID:19848142

Isotopic variability of mercury in ore, mine-waste calcine, and leachates of mine-waste calcine from areas mined for mercury

USGS Publications Warehouse

Stetson, S.J.; Gray, J.E.; Wanty, R.B.; Macalady, D.L.

2009-01-01

The isotopic composition of mercury (Hg) was determined in cinnabar ore, mine-waste calcine (retorted ore), and leachates obtained from water leaching experiments of calcine from two large Hg mining districts in the U.S. This study is the first to report significant mass-dependent Hg isotopic fractionation between cinnabar ore and resultant calcine. Data indicate that ??202Hg values relative to NIST 3133 of calcine (up to 1.52???) in the Terlingua district, Texas, are as much as 3.24??? heavier than cinnabar (-1.72???) prior to retorting. In addition, ??202Hg values obtained from leachates of Terlingua district calcines are isotopically similar to, or as much as 1.17??? heavier than associated calcines, most likely due to leaching of soluble, byproduct Hg compounds formed during ore retorting that are a minor component in the calcines. As a result of the large fractionation found between cinnabar and calcine, and because calcine is the dominant source of Hg contamination from the mines studied, ??202Hg values of calcine may be more environmentally important in these mined areas than the primary cinnabar ore. Measurement of the Hg isotopic composition of calcine is necessary when using Hg isotopes for tracing Hg sources from areas mined for Hg, especially mine water runoff. ?? 2009 American Chemical Society.

75 FR 28227 - National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-20

... published a proposed rule for mercury emissions from the gold mine ore processing and production area source... proposed rule (75 FR 22470). Several parties requested that EPA extend the comment period. EPA has granted...-AP48 National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production...

Lunar vertical-shaft mining system

NASA Technical Reports Server (NTRS)

Introne, Steven D. (Editor); Krause, Roy; Williams, Erik; Baskette, Keith; Martich, Frederick; Weaver, Brad; Meve, Jeff; Alexander, Kyle; Dailey, Ron; White, Matt

1994-01-01

This report proposes a method that will allow lunar vertical-shaft mining. Lunar mining allows the exploitation of mineral resources imbedded within the surface. The proposed lunar vertical-shaft mining system is comprised of five subsystems: structure, materials handling, drilling, mining, and planning. The structure provides support for the exploration and mining equipment in the lunar environment. The materials handling subsystem moves mined material outside the structure and mining and drilling equipment inside the structure. The drilling process bores into the surface for the purpose of collecting soil samples, inserting transducer probes, or locating ore deposits. Once the ore deposits are discovered and pinpointed, mining operations bring the ore to the surface. The final subsystem is planning, which involves the construction of the mining structure.

Optimization research of structural parameters in non-pillar sublevel caving method with large structural parameters

NASA Astrophysics Data System (ADS)

Han, Wencheng; Zhou, Renjie; Liu, Xianfeng; Sun, Dongdong

2018-03-01

The non-pillar sublevel caving method with large structural parameters used in Mao Gong Iron Mine is of high rate of dilution and loss, and the ore recovery rate is less than 50%. Aiming at this problem, this paper analyzes the influence mechanism of the caving step on the mining index by means of the matching relationship between the shape of caved ore body and the drawn-out ore body, then through the physical simulation experiment in laboratory, the mining index such as the volume of pure ore drawing, ore recovery ratio and rock mixing ratio are studied under different caving step. The results show that the mining index under caving step of two row of blast hole is better than that under caving step of one row of blast hole. The research has guided significance for production of the mine.

TOTAL ORE PROCESSING INTEGRATION AND MANAGEMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leslie Gertsch; Richard Gertsch

2005-05-16

The lessons learned from ore segregation test No.3 were presented to Minntac Mine personnel during the reporting period. Ore was segregated by A-Factor, with low values going to Step 1/2 and high values going to Step 3. During the test, the mine maintained the best split possible for the given production and location constraints. During the test, Step 1&2 A-Factor was lowered more than Step 3 was raised. All other ore quality changes were not manipulated, but the segregation by A-Factor affected most of the other qualities. Magnetic iron, coarse tails, fine tails, silica, and grind changed in response tomore » the split. Segregation was achieved by adding ore from HIS to the Step 3 blend and lowering the amount of LC 1&2 and somewhat lowering the amount of LC 3&4. Conversely, Step 1&2 received less HIS with a corresponding increase in LC 1&2. The amount of IBC was increased to both Steps about one-third of the way into the test. For about the center half of the test, LC 3&4 was reduced to both Steps. The most noticeable layer changes were, then: an increase in the HIS split; a decrease in the LC 1&2 split; adding IBC to both Steps; and lowering LC 3&4 to both Steps. Statistical analysis of the dataset collected during ordinary, non-segregated operation of the mine and mill is continuing. Graphical analysis of blast patterns according to drill monitor data was slowed by student classwork. It is expected to resume after the semester ends in May.« less

Geology and ore deposits of the Section 23 Mine, Ambrosia Lake District, New Mexico

USGS Publications Warehouse

Granger, H.C.; Santos, E.S.

1982-01-01

The section 23 mine is one of about 18 large uranium mines opened in sandstones of the fluvial Westwater Canyon Member of the Jurassic Morrison Formation in the Ambrosia Lake mining district during the early 1960s. The Ambrosia Lake district is one of several mining districts within the Grants mineral belt, an elongate zone containing many uranium deposits along the southern flank of the San Juan basin. Two distinct types of ore occur in the mine. Primary ore occurs as peneconcordant layers of uranium-rich authigenic organic matter that impregnates parts of the reduced sandstone host rocks and which are typically elongate in an east-southeast direction subparallel both to the sedimentary trends and to the present-day regional strike of the strata. These are called prefault or trend ores because of their early genesis and their elongation and alinement. A second type of ore in the mine is referred to as postfault, stacked, or redistributed ore. Its genesis was similar to that of the roll-type deposits in Tertiary rocks of Wyoming and Texas. Oxidation, related to the development of a large tongue of oxidized rock extending from Gallup to Ambrosia Lake, destroyed much of the primary ore and redistributed it as massive accumulations of lower grade ores bordering the redox interface at the edge of the tongue. Host rocks in the southern half of sec. 23 (T. 14 N., R. 10 W.) are oxidized and contain only remnants of the original, tabular, organic-rich ore. Thick bodies of roll-type ore are distributed along the leading edge of the oxidized zone, and pristine primary ore is found only near the north edge of the section. Organic matter in the primary ore was derived from humic acids that precipitated in the pores of the sandstones and fixed uranium as both coffinite and urano-organic compounds. Vanadium, molybdenum, and selenium are also associated with the ore. The secondary or roll-type ores are essentially free of organic carbon and contain uranium both as coffinite and uraninite. They also contain vanadium and selenium but are virtually devoid of molybdenum. Although much has been learned about these deposits since the time this study was conducted, in 1966, a great deal more study will by required to completely elucidate their geologic history.

43 CFR 3486.3 - Enforcement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... mine, the deposit being mined, valuable ore-bearing mineral deposits or other resources, or affect the... the authorized officer, and/or which threaten immediate and serious damage to the mine, the deposit being mined, valuable ore-bearing mineral deposits, or, regarding exploration, the environment, the...

40 CFR 440.140 - Applicability; description of the gold placer mine subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE... that produce gold or gold bearing ores from placer deposits; and (2) The beneficiation processes which... yards (cu yd) of ore per year, or to dredges which process less than 50,000 cu yd of ore per year, or to...

40 CFR 440.140 - Applicability; description of the gold placer mine subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE... that produce gold or gold bearing ores from placer deposits; and (2) The beneficiation processes which... yards (cu yd) of ore per year, or to dredges which process less than 50,000 cu yd of ore per year, or to...

40 CFR 440.140 - Applicability; description of the gold placer mine subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE... that produce gold or gold bearing ores from placer deposits; and (2) The beneficiation processes which... yards (cu yd) of ore per year, or to dredges which process less than 50,000 cu yd of ore per year, or to...

Using Local Event Tomography to Image Changes in the Rock Mass in the Kiirunavaara Iron Ore Mine, Northern Sweden

NASA Astrophysics Data System (ADS)

Lund, B.; Berglund, K.; Tryggvason, A.; Dineva, S.; Jonsson, L.

2017-12-01

Although induced seismic events in a mining environment are a potential hazard, they can be used to gain information about the rock mass in the mine which otherwise would be very difficult to obtain. In this study we use approximately 1.2 million mining induced seismic events in the Kiirunavaara iron ore mine in northernmost Sweden to image the rock mass using local event travel-time tomography. The Kiirunavaara mine is the largest underground iron ore mine in the world. The ore body is a magnetite sheet of 4 km length, with an average thickness of 80 m, which dips approximately 55° to the east. The events are of various origins such as shear slip on fractures, non-shear events and blasts, with magnitudes of up to 2.5. We use manually picked P- and S-wave arrival times from the routine processing in the tomography and we require that both phases are present at at least five geophones. For the tomography we use the 3D local earthquake tomography code PStomo_eq (Tryggvason et al., 2002), which we adjusted to the mining scale. The tomographic images show clearly defined regions of high and low velocities. Prominent low S-velocity zones are associated with mapped clay zones. Regions of ore where mining is ongoing and the near-ore tunnel infrastructure in the foot-wall also show generally low P- and S-velocities. The ore at depths below the current mining levels is imaged both as a low S-velocity zone but even more pronounced as a high Vp/Vs ratio zone. The tomography shows higher P- and S-velocities in the foot-wall away from the areas of mine infrastructure. We relocate all 1.2 million events in the new 3D velocity model. The relocation significantly enhances the clarity of the event distribution in space and we can much more easily identify seismically active structures, such as e.g. the deformation of the ore passes. The large number of events makes it possible to do detailed studies of the temporal evolution of stability in the mine. We present preliminary results of time-lapse tomography in an area where a few events of magnitude 2+ occurred in September 2015. We also image temporal velocity changes around the mining front at depth.

Development and application of biotechnologies in the metal mining industry.

PubMed

Johnson, D Barrie

2013-11-01

Metal mining faces a number of significant economic and environmental challenges in the twenty-first century for which established and emerging biotechnologies may, at least in part, provide the answers. Bioprocessing of mineral ores and concentrates is already used in variously engineered formats to extract base (e.g., copper, cobalt, and nickel) and precious (gold and silver) metals in mines throughout the world, though it remains a niche technology. However, current projections of an increasing future need to use low-grade primary metal ores, to reprocess mine wastes, and to develop in situ leaching technologies to extract metals from deep-buried ore bodies, all of which are economically more amenable to bioprocessing than conventional approaches (e.g., pyrometallurgy), would suggest that biomining will become more extensively utilized in the future. Recent research has also shown that bioleaching could be used to process a far wider range of metal ores (e.g., oxidized ores) than has previously been the case. Biotechnologies are also being developed to control mine-related pollution, including securing mine wastes (rocks and tailings) by using "ecological engineering" approaches, and also to remediate and recover metals from waste waters, such as acid mine drainage. This article reviews the current status of biotechnologies within the mining sector and considers how these may be developed and applied in future years.

Cyanide hazards to plants and animals from gold mining and related water issues

USGS Publications Warehouse

Eisler, R.; Wiemeyer, Stanley N.

2004-01-01

Highly toxic sodium cyanide (NaCN) is used by the international mining community to extract gold and other precious metals through milling of high-grade ores and heap leaching of low-grade ores (Korte et al. 2000). The process to concentrate gold using cyanide was developed in Scotland in 1887 and was used almost immediately in the Witwatersrand gold fields of the Republic of South Africa. Heap leaching with cyanide was proposed by the U.S. Bureau of Mines in 1969 as a means of extracting gold from low-grade ores. The gold industry adopted the technique in the 1970s, soon making heap leaching the dominant technology in gold extraction (Da Rosa and Lyon 1997). The heap leach and milling processes, which involve dewatering of gold-bearing ores, spraying of dilute cyanide solutions on extremely large heaps of ores containing low concentrations of gold, or the milling of ores with the use of cyanide and subsequent recovery of the gold-cyanide complex, have created a number of serious environmental problems affecting wildlife and water management. In this account, we review the history of cyanide use in gold mining with emphasis on heap leach gold mining, cyanide hazards to plants and animals, water management issues associated with gold mining, and proposed mitigation and research needs.

Water quality data at selected sites in the Mississippi Valley-type Zn-Pb ore district of upper Silesia, Poland, 1995-97

USGS Publications Warehouse

Wirt, Laurie; Motyka, Jacek; Leach, David; Sass-Gustkiewicz, Maria; Szuwarzynski, Marek; Adamczyk, Zbigniew; Briggs, Paul; Meiers, Al

2003-01-01

The water chemistry of aquifers and streams in the Upper Silesia Ore District, Poland are affected by their proximity to zinc, lead, and silver ores and by ongoing mining activities that date back to the 11th century. This report presents hydrologic and water-quality data collected as part of a collaborative research effort of the U.S. Geological Survey and the University of Mining and Metallurgy in Cracow, Poland to study Mississippi-Valley-Type lead-zinc deposits. MVT deposits in the Upper Silesia Ore District (Fig. 1) were selected for detailed study because the Polish mining industry allowed access to collect samples from underground mines and mine-land property. Water-quality samples were collected from streams, springs, wells, underground mine seeps and drains; and mine-tailings ponds. Data include field measurements of specific conductance, pH, water temperature, and dissolved oxygen and laboratory analyses of major and minor inorganic constituents and selected trace-element constituents.

Solubility and chemistry of materials encountered by beryllium mine and ore extraction workers: relation to risk.

PubMed

Deubner, David C; Sabey, Philip; Huang, Wenjie; Fernandez, Diego; Rudd, Abigail; Johnson, William P; Storrs, Jason; Larson, Rod

2011-10-01

Beryllium mine and ore extraction mill workers have low rates of beryllium sensitization and chronic beryllium disease relative to the level of beryllium exposure. The objective was to relate these rates to the solubility and composition of the mine and mill materials. Medical surveillance and exposure data were summarized. Dissolution of BeO, ore materials and beryllium hydroxide, Be(OH)(2) was measured in synthetic lung fluid. The ore materials were more soluble than BeO at pH 7.2 and similar at pH 4.5. Be(OH)(2) was more soluble than BeO at both pH. Aluminum dissolved along with beryllium from ore materials. Higher solubility of beryllium ore materials and Be(OH)(2) at pH 7.2 might shorten particle longevity in the lung. The aluminum content of the ore materials might inhibit the cellular immune response to beryllium.

Hepatic retinoid levels in seven fish species (teleosts) from a tropical coastal lagoon receiving effluents from iron-ore mining and processing.

PubMed

Pereira, Adriana A; van Hattum, Bert; Brouwer, Abraham

2012-02-01

The present study was undertaken to investigate the possible effects of Fe and trace element exposure on hepatic levels of retinoids in seven fish species. Concentrations of retinoids were measured in fish collected from a coastal lagoon in Brazil that receives effluents from an iron-ore mining and processing plant. Fish from nearby coastal lagoons were also included to assess possible differences related to chemical exposure. Results indicated considerable differences in hepatic retinoid composition among the various species investigated. The most striking differences were in retinol and derivative-specific profiles and in didehydro retinol and derivative-specific profiles. The Perciformes species Geophagus brasiliensis, Tilapia rendalli, Mugil liza, and Cichla ocellaris and the Characiforme Hoplias malabaricus were characterized as retinol and derivative-specific, while the Siluriformes species Hoplosternum littorale and Rhamdia quelen were didehydro retinol and derivative-specific fish species. A negative association was observed between Al, Pb, As, and Cd and hepatic didehydro retinoid levels. Fish with higher levels of hepatic Fe, Cu, and Zn showed unexpectedly significant positive correlations with increased hepatic retinol levels. This finding, associated with the positive relationships between retinol and retinyl palmitate with lipid peroxidation, may suggest that vitamin A is mobilized from other tissues to increase hepatic antioxidant levels for protection against oxidative damage. These data show significant but dissimilar associations between trace element exposure and hepatic retinoid levels in fish species exposed to iron-ore mining and processing effluents, without apparent major impacts on fish health and condition. Copyright © 2011 SETAC.

40 CFR 63.11651 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... mine ore at gold mine ore processing and production facilities prior to the cyanide leaching process... are generated from leaching gold ore with a dilute cyanide solution. Quenching means a process in... the presence of steam, after the gold has been stripped from the carbon. Carbon processes with mercury...

40 CFR 440.104 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

..., in-situ leach or vat-leach processes to extract copper from ores or ore waste materials. The Agency... Molybdenum Ores Subcategory § 440.104 New source performance standards (NSPS). Except as provided in subpart... technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines that produce...

40 CFR 440.104 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

..., in-situ leach or vat-leach processes to extract copper from ores or ore waste materials. The Agency... Molybdenum Ores Subcategory § 440.104 New source performance standards (NSPS). Except as provided in subpart... technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines that produce...

Mineral commodity profiles: Silver

USGS Publications Warehouse

Butterman, W.C.; Hilliard, Henry E.

2005-01-01

Overview -- Silver is one of the eight precious, or noble, metals; the others are gold and the six platinum-group metals (PGM). World mine production in 2001 was 18,700 metric tons (t) and came from mines in 60 countries; the 10 leading producing countries accounted for 86 percent of the total. The largest producer was Mexico, followed by Peru, Australia, and the United States. About 25 percent of the silver mined in the world in 2001 came from silver ores; 15 percent, from gold ores and the remaining 60 percent, from copper, lead, and zinc ores. In the United States, 14 percent of the silver mined in 2001 came from silver ores; 39 percent, from gold ores; 10 percent, from copper and copper-molybdenum ores; and 37 percent, from lead, zinc, and lead-zinc ores. The precious metal ores (gold and silver) came from 30 lode mines and 10 placer mines; the base-metal ores (copper, lead, molybdenum, and zinc) came from 24 lode mines. Placer mines yielded less than 1 percent of the national silver production. Silver was mined in 12 States, of which Nevada was by far the largest producer; it accounted for nearly one-third of the national total. The production of silver at domestic mines generated employment for about 1,100 mine and mill workers. The value of mined domestic silver was estimated to be $290 million. Of the nearly 27,000 t of world silver that was fabricated in 2001, about one-third went into jewelry and silverware, one-fourth into the light-sensitive compounds used in photography, and nearly all the remainder went for industrial uses, of which there were 7 substantial uses and many other small-volume uses. By comparison, 85 percent of the silver used in the United States went to photography and industrial uses, 8 percent to jewelry and silverware, and 7 percent to coins and medals. The United States was the largest consumer of silver followed by India, Japan, and Italy; the 13 largest consuming countries accounted for nearly 90 percent of the world total. In the United States, about 30 companies accounted for more than 90 percent of the silver fabricated. The consumption of silver for all fabrication uses is expected to grow slowly through the decade ending in 2010 at about 1.3 percent per year for the world and 2.4 percent per year for the United States. World and U.S. reserves and reserve bases are more than adequate to satisfy the demand for newly mined silver through 2010. The other components of supply will be silver recovered from scrap, silver from industrial stocks, and silver bullion that is sold into the market from commodity exchange and private stocks.

A Metal Stable Isotope Approach to Understanding Uranium Mobility Across Roll Front Redox Boundaries

NASA Astrophysics Data System (ADS)

Brown, S. T.; Basu, A.; Christensen, J. N.; DePaolo, D. J.; Heikoop, J. M.; Reimus, P. W.; Maher, K.; Weaver, K. L.

2015-12-01

Sedimentary roll-front uranium (U) ore deposits are the principal source of U for nuclear fuel in the USA and an important part of the current all-of-the-above energy strategy. Mining of roll-front U ore in the USA is primarily by in situ alkaline oxidative dissolution of U minerals. There are significant environmental benefits to in situ mining including no mine tailings or radioactive dust, however, the long-term immobilization of U in the aquifer after the completion of mining remains uncertain. We have utilized the metal stable isotopes U, Se and Mo in groundwater from roll-front mines in Texas and Wyoming to quantify the aquifer redox conditions and predict the onset of U reduction after post mining aquifer restoration. Supporting information from the geochemistry of groundwater and aquifer sediments are used to understand the transport of U prior to and after in situ mining. Groundwater was collected across 4 mining units at the Rosita mine in the Texas coastal plain and 2 mining units at the Smith Ranch mine in the Powder River Basin, Wyoming. In general, the sampled waters are moderately reducing and ore zone wells contain the highest aqueous U concentrations. The lowest U concentrations occur in monitoring wells downgradient of the ore zone. 238U/235U is lowest in downgradient wells and is correlated with aqueous U concentrations. Rayleigh distillation models of the 238U/235U are consistent with U isotope fractionation factors of 1.0004-1.001, similar to lab-based studies. Based on these results we conclude that redox reactions continue to affect U distribution in the ore zone and downgradient regions. We also measured aqueous selenium isotope (δ82Se) and molybdenum isotope (δ98Mo) compositions in the Rosita groundwater. Se(VI) primarily occurs in the upgradient wells and is absent in most ore zone and downgradient wells. Rayleigh distillation models suggest reduction of Se(VI) along the groundwater flow path and when superimposed on the U isotope data Se reduction is favored over U reduction. The δ98Mo of Rosita groundwater is significantly elevated compared to the U ore and is negatively correlated with the groundwater Eh, which suggests localized strong reducing conditions capable of Mo reduction. Ongoing work will determine the Mo isotope systematics of U ores and groundwater from roll-front deposits.

Radon emanation from low-grade uranium ore.

PubMed

Sahu, Patitapaban; Mishra, Devi Prasad; Panigrahi, Durga Charan; Jha, Vivekanand; Patnaik, R Lokeswara

2013-12-01

Estimation of radon emanation in uranium mines is given top priority to minimize the risk of inhalation exposure due to short-lived radon progeny. This paper describes the radon emanation studies conducted in the laboratory as well as inside an operating underground uranium mine at Jaduguda, India. Some of the important parameters, such as grade/(226)Ra activity, moisture content, bulk density, porosity and emanation fraction of ore, governing the migration of radon through the ore were determined. Emanation from the ore samples in terms of emanation rate and emanation fraction was measured in the laboratory under airtight condition in glass jar. The in situ radon emanation rate inside the mine was measured from drill holes made in the ore body. The in situ(222)Rn emanation rate from the mine walls varied in the range of 0.22-51.84 × 10(-3) Bq m(-2) s(-1) with the geometric mean of 8.68 × 10(-3) Bq m(-2) s(-1). A significant positive linear correlation (r = 0.99, p < 0.001) between in situ(222)Rn emanation rate and the ore grade was observed. The emanation fraction of the ore samples, which varied in the range of 0.004-0.089 with mean value of 0.025 ± 0.02, showed poor correlation with ore grade and porosity. Empirical relationships between radon emanation rate and the ore grade/(226)Ra were also established for quick prediction of radon emanation rate from the ore body. Copyright © 2013 Elsevier Ltd. All rights reserved.

Preparation of ore blocks for mine leaching by reagent explosion injection

NASA Astrophysics Data System (ADS)

Shevchenko, YuS

2017-02-01

The current drilling-and-blasting operations fail to prepare intact ore body underlying a production horizon for subsequent mining and leaching. It is found that the required preparation quality is possible by means of advanced implementation of ore body discontinuity and filling of the resultant system of joints with active leaching solutions.

Natural radiation and its hazard in copper ore mines in Poland

NASA Astrophysics Data System (ADS)

Chau, Nguyen; Jodłowski, Paweł; Kalita, Stefan; Olko, Paweł; Chruściel, Edward; Maksymowicz, Adam; Waligórski, Michał; Bilski, Paweł; Budzanowski, Maciej

2008-06-01

The doses of gamma radiation, concentrations of radium isotopes in water and sediments, radon concentration and concentration of alpha potential energy of radon decay products in the copper ore mine and in the mining region in the vicinity of Lubin town in Poland are presented. These data served as a basis for the assessment of radiological hazard to the mine workers and general public. The results of this assessment indicate that radiological hazard in the region does not differ substantially from typical values associated with natural radiation background. The calculated average annual effective dose for copper miners is 1.48 mSv. In general, copper ore mines can be regarded as radiologically safe workplaces.

The Labour Welfare Fund Laws (Amendment) Act, 1987 (No. 15 of 1987), 22 May 1987.

PubMed

1987-01-01

This Act authorizes funds constituted under the Mica Mines Labour Welfare Fund Act, 1946, the Limestone and Dolomite Mines Labour Welfare Fund Act, 1972, the Iron Ore Mines, Manganese Ore Mines and Chrome Mines Labour Welfare Fund Act, 1976, and the Beedi Workers Welfare Fund Act, 1976, to be applied for the provision of family welfare, including family planning education and services. full text

Rational design of bottom blocks for development of ore deposits systems with caving of ore and enclosing rocks

NASA Astrophysics Data System (ADS)

Versilov, S. O.; Posylniy, Yu V.; Shurygin, D. N.; Tretyak, A. Ya

2017-10-01

The assessment of the geological conditions of development of existing ore deposits was made. For testing ore deposits in difficult mining and geological conditions, the authors proposed the system of development, accompanied by collapse of the mechanical ore with the use of feeders of active action that could be manufactured directly in the mine in accordance with the specific conditions of occurrence of minerals. The paper demonstrates the technology of manufacture of load-bearing structures of the feeder directly in the mine at the scene of the breaking of the first layer of ore, as well as the dynamics of the ore and the choice of parameters of concrete feeders. A new design of the bottom block was proposed, the idea of technical solution of which consists in the fact that it is offered to undergo the production of the smallest possible cross section, which is determined only by the dimensions of the conveyors to deliver ore. And before the explosion of fans of production wells, it is necessary to produce local collapse of the roof production to increase its height at the place of production of ore by blasting wellheads in two or three rows.

General geology and mines of the East Tintic mining district, Utah and Juab counties, Utah, with sections on the geology of the Burgin mine and the geology of the Trixie mine

USGS Publications Warehouse

Morris, H.T.; Lovering, Thomas Seward; Mogensen, A.P.; Shepard, W.M.; Perry, L.I.; Smith, S.M.

1979-01-01

This report is a study of the rocks, geologic structures, and mines of a highly productive silver, gold, and base-metal mining district in the east-central Great Basin. The East Tintic mining district is in the east-central part of the East Tintic Mountains, near the east margin of the Basin and Range province in Utah and Juab Counties, Utah. The district occupies the northeastern part of the Eureka quadrangle and is about 5 mi (8 km) wide and 6 mi (9.7 km) long. Officially it is within the designated boundaries of the Tintic mining district, but it generally though erroneously has been regarded as a separate district since the late 1800's.Prospecting was first undertaken in East Tintic in 1870; although small quantities of ore were produced in 1899 and from 1909 to 1913, the district first achieved prominence in 1916 with the discovery of the totally concealed Central ore body of the Tintic Standard mine. Within a few years of this discovery, the Tintic Standard became one of the most productive silver mines in the world. Additional discoveries of important concealed ore deposits have continued to be made in the district, including the North Lily mine in 1927, the Eureka Lilly and Eureka Standard mines in 1928, the Burgin mine in 1958, and the Trixie mine in 1969.To December 31, 1975, the East Tintic mining district has yielded approximately 4.83 million short tons (4.38 million tonnes) of silver, gold, and base-metal ores, largely from concealed deposits overlain by many hundreds of feet of barren rocks. These ores have a gross valuation of approximately $231 million. The district first achieved prominence in 1916 with the discovery of the ore bodies of the Tintic Standard mine, which for a time was the world's richest silver producer (Lindgren, 1933, p. 588). By 1946 this deposit and a number of other deposits discovered and developed nearby had been exhausted, and the district became dormant. A dramatic revival of, mining activities in the East Tintic district began in 1956 after the discovery and subsequent development of the concealed Burgin ore bodies in an area 1 mile (1.6 km) southeast of the Tintic Standard that previously had been only superficially prospected. As in the earlier history of the district, the Burgin development has led to the discovery of other concealed deposits, focusing international attention on the revitalization of a nearly abandoned mining district by the application of geologic and geochemical techniques.

Bioprocessing of ores: Application to space resources

NASA Technical Reports Server (NTRS)

Johansson, Karl R.

1992-01-01

The role of microorganisms in the oxidation and leaching of various ores (especially those of copper, iron, and uranium) is well known. This role is increasingly being applied by the mining, metallurgy, and sewage industries in the bioconcentration of metal ions from natural receiving waters and from waste waters. It is concluded that bioprocessing using bacteria in closed reactors may be a variable option for the recovery of metals from the lunar regolith. Obviously, considerable research must be done to define the process, specify the appropriate bacteria, determine the necessary conditions and limitations, and evaluate the overall feasibility.

40 CFR 440.148 - Best Management Practices (BMP).

Code of Federal Regulations, 2013 CFR

2013-07-01

... GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine... control: The amount of new water allowed to enter the plant site for use in ore processing shall be...

40 CFR 440.148 - Best Management Practices (BMP).

Code of Federal Regulations, 2012 CFR

2012-07-01

... GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine... control: The amount of new water allowed to enter the plant site for use in ore processing shall be...

40 CFR 440.148 - Best Management Practices (BMP).

Code of Federal Regulations, 2014 CFR

2014-07-01

... GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine... control: The amount of new water allowed to enter the plant site for use in ore processing shall be...

Reflection seismic characterization of the Grängesberg iron deposit and its mining-induced structures, central Sweden

NASA Astrophysics Data System (ADS)

Place, Joachim; Malehmir, Alireza; Högdahl, Karin; Juhlin, Christopher; Persson Nilsson, Katarina

2014-05-01

Reflection seismic investigation has been conducted on the Grängesberg apatite iron deposit where over 150 Mt of iron ore were produced until the mine closed in 1989. The mine infrastructure with shafts and tunnels extend down to ca. 650 m below the surface. Both natural and mine induced fracture and fault systems are today water-filled (some of them extending to the surface). The disputed ore genesis of the apatite-iron ores and its exploration potential due to large remaining quantities once again attracts both scientific and commercial interests. A good understanding of the geometry of mineral deposits and their hostrock structures at depth is essential for optimizing their exploration and exploitation. In addition, deep understanding of the fracture system is vital if mining activity is resumed as these may impact the terrain stability and seismicity, which may put at risk new populated and industrial areas. To address some of these challenging issues related to the past mining and also to obtain information about the depth continuation of the existing deposit, two E-W oriented reflection lines with a total length of 3.5 km were acquired in May 2013 by Uppsala University. A weight drop mounted on an hydraulic bobcat truck (traditionally used for concrete breaking in demolition sector) was used to generate seismic signal. In order to increase the signal-to-noise ratio, several impacts were generated at each shot point and stacked together. The seismic lines intersect at high angle the Grängesberg ore body and open pit, as well as several mining-induced faults. A combination of cabled and wireless receivers placed at every 10 m was used for the data recording. Use of wireless receivers was necessary as deploying cabled sensors was not possible due to city infrastructures, roads and houses. A careful analysis of the data suggested that several field-related issues such as (1) the crooked geometry of the lines (due to the available path and road network), (2) electric and vibration noise due to populated areas and roads, as well as a rock crusher working close to the line, (3) significant static variations (due to the variable nature of the terrain: forest, roads, open pit filled with 10s of meters of unconsolidated materials...), make this dataset similar to a city-kind dataset. Preprocessing of the data first required the cable- and wireless- recorded sub-datasets to be merged using GPS time stamps (nanoseconds accuracy) registered in the active data. Vertical shift and stack was then carried out to stack all data available at each shot point. Preliminary results from brute stacks exhibit evidences of reflections or diffractions. It is anticipated that further processing, involving especially appropriate static corrections and velocity analysis, would help interpreting such seismic events in relation to the ore body and its surrounding structures. Possible along-profile compartmentalization is also detected; further processing is however necessary before interpreting such features in terms of recent faulting. Acknowledgements: Formas, Grängesberg Iron AB, Spendrups and Geological Survey of Sweden

Physical, chemical and antimicrobial characterization of copper-bearing material

NASA Astrophysics Data System (ADS)

Li, Bowen; Hwang, Jiann-Yang; Drelich, Jaroslaw; Popko, Domenic; Bagley, Susan

2010-12-01

Arsenic, cadmium, copper, mercury, silver, and zinc are elements with strong antimicrobial properties. Among them, copper is more environmentally friendly and has both good antibacterial and antifungal properties. It has been shown that copper can even be effective against new viruses such as avian influenza (H5N1). Development of copper-bearing materials for various applications, therefore, is receiving increased attention. The Keweenaw Peninsula of Michigan was the largest native copper mining regions of North America at the turn of the 20th century. Copper was extracted by mining the copper-rich basaltic rock, and steamdriven stamp mills were used to process a great volume of low-grade ores, resulting in huge amounts of crushed waste ore called stamp sands. Approximately 500 million tons of stamp sand were discarded. This material is investigated in this study as an example for the development of antimicrobial materials.

Imaging the state of the rock mass in the Kiirunavaara iron ore mine, Sweden, using local event tomography

NASA Astrophysics Data System (ADS)

Lund, Björn; Berglund, Karin; Tryggvason, Ari; Dineva, Savka; Jonsson, Linda

2017-04-01

Induced seismic events in a mining environment are a potential hazard, but they can be used to gain information about the rock mass in the mine which otherwise would be very difficult to obtain. In this study we use approximately 1.2 million mining induced seismic events in the Kiirunavaara iron ore mine in northernmost Sweden to image the rock mass using local event travel-time tomography. In addition, relocation of the events significantly improves the possibility to infer structural information and rock damage. The Kiirunavaara mine is one of the largest underground iron ore mines in the world. The ore body is a magnetite sheet of 4 km length, with an average thickness of 80 m, which dips approximately 55° to the east. Mining production is now at a depth of 785 - 855 m. During 2015 the seismic system in the mine recorded on average approximately 1,000 local seismic events per day. The events are of various origins such as shear slip on fractures, non-shear events and blasts, with magnitudes of up to 2.5. We use manually picked P- and S-waves in the tomography and we require that both phases are present as we found that events from the routine processing need screening for anomalous P- versus S-travel times, indicating occasional erroneous phase associations. For the tomography we use the 3D local earthquake tomography code PStomo_eq (Tryggvason et al., 2002), which we adjusted to the mining scale. The study volume is 1.2 x 1.8 x 1.8 km and the velocity model grid size is 10x10x10 meter. The tomographic images show clearly defined regions of high and low velocities. Low velocity zones are associated with mapped clay zones and areas of mined out ore, and also with the near-ore tunnel infrastructure in the foot-wall. We also see how the low S-velocity anomaly continues to depth below the current mining levels, following the inferred direction of the ore. The tomography shows higher P- and S-velocities in the foot-wall away from the areas of mine infrastructure. We relocate all 1.2 million events in the new 3D velocity model. The relocation significantly enhances the clarity of the event distribution in space and we can much more easily identify seismically active structures. One example of this is the clarity with which deformation of the ore-passes is correlated with the intensity and distribution of relocated seismic events. The relocations also show more structures in areas of the mine where rock stability is a significant problem. The large number of events makes it possible to do detailed studies of the temporal evolution of stability in the mine. We present preliminary results of time-lapse tomography in an area where a few events of magnitude 2+ occurred in September 2015.

A REAL-TIME COAL CONTENT/ORE GRADE (C2OC) SENSOR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rand Swanson

2005-04-01

This is the final report of a three year DOE funded project titled ''A real-time coal content/ore grade (C{sub 2}OG) sensor''. The sensor, which is based on hyperspectral imaging technology, was designed to give a machine vision assay of ore or coal. Sensors were designed and built at Resonon, Inc., and then deployed at the Stillwater Mining Company core room in southcentral Montana for analyzing platinum/palladium ore and at the Montana Tech Spectroscopy Lab for analyzing coal and other materials. The Stillwater sensor imaged 91' of core and analyzed this data for surface sulfides which are considered to be pathfindermore » minerals for platinum/palladium at this mine. Our results indicate that the sensor could deliver a relative ore grade provided tool markings and iron oxidation were kept to a minimum. Coal, talc, and titanium sponge samples were also imaged and analyzed for content and grade with promising results. This research has led directly to a DOE SBIR Phase II award for Resonon to develop a down-hole imaging spectrometer based on the same imaging technology used in the Stillwater core room C{sub 2}OG sensor. The Stillwater Mining Company has estimated that this type of imaging system could lead to a 10% reduction in waste rock from their mine and provide a $650,000 benefit per year. The proposed system may also lead to an additional 10% of ore tonnage, which would provide a total economic benefit of more than $3.1 million per year. If this benefit could be realized on other metal ores for which the proposed technology is suitable, the possible economic benefits to U.S. mines is over $70 million per year. In addition to these currently lost economic benefits, there are also major energy losses from mining waste rock and environmental impacts from mining, processing, and disposing of waste rock.« less

40 CFR 440.83 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.83 Effluent limitations representing...

40 CFR 440.83 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.83 Effluent limitations representing...

40 CFR 440.85 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.85 Effluent limitations representing...

40 CFR 440.85 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.85 Effluent limitations representing...

40 CFR 440.148 - Best Management Practices (BMP).

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine Subcategory § 440.148...: The amount of new water allowed to enter the plant site for use in ore processing shall be limited to...

40 CFR 440.83 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.83 Effluent limitations representing...

40 CFR 440.85 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct) § 440.85 Effluent limitations representing...

ORE CONVEYANCE SYSTEM AND ADIT. LOOKING WEST. ORE FROM THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ORE CONVEYANCE SYSTEM AND ADIT. LOOKING WEST. ORE FROM THE MINES ABOVE AT THE RIDGELINE AND TO THE RIGHT WAS CONVEYED TO THIS AREA AND DUMPED INTO THE SHAFT AT CENTER. THIS SHAFT OPENS INTO THE ADIT AT BOTTOM CENTER. THERE IS ANOTHER SHAFT OPENING INTO THE ADIT JUST ABOVE THE ADIT BEHIND THE STONE WALL. THE ORE WAS LOADED INTO TRAM CARS INSIDE THE ADIT AND CONVEYED ON TRACKS TO THE TRESTLE LEADING TO THE PRIMARY ORE BIN AT THE TRAM TERMINAL. TRACKS CAN BE SEEN LEADING FROM THE ADIT AND TO THE LEFT. THE ORE WAS THEN DUMPED INTO A CHUTE AT THE END OF THE TRESTLE CARRYING IT INTO THE ORE BIN AT THE TRAM TERMINAL(SEE CHUTE ON CA-291-30). - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Environmental geochemistry of abandoned mercury mines in West-Central Nevada, USA

USGS Publications Warehouse

Gray, J.E.; Crock, J.G.; Fey, D.L.

2002-01-01

The Humboldt River is a closed basin and is the longest river in Nevada. Numerous abandoned Hg mines are located within the basin, and because Hg is a toxic heavy metal, the potential transport of Hg from these mines into surrounding ecosystems, including the Humboldt River, is of environmental concern Samples of ore, sediment, water, calcines (roasted ore), and leachates of the calcines were analyzed for Hg and other heavy metals to evaluate geochemical dispersion from the mines. Cinnabar-bearing ore samples collected from the mines contain highly elevated Hg concentrations, up to 6.9 %, whereas calcines collected from the mines contain up to 2000 mg Hg/kg. Stream-sediment samples collected within 1 km of the mines contain as much as 170 mg Hg/kg, but those collected distal from the mines (> 5 km) contain 8 km from the Humboldt River, and Hg is transported and diluted through a large volume of pediment before it reaches the Humboldt River. ?? 2002 Elsevier Science Ltd. All rights reserved.

Possibilities of magnetotelluric methods in geophysical exploration for ore minerals

NASA Astrophysics Data System (ADS)

Varentsov M., Iv.; Kulikov, V. A.; Yakovlev, A. G.; Yakovlev, D. V.

2013-05-01

In the past decade, the applications of magnetotelluric method in the electric prospecting for ore bodies have been rapidly progressing. In the present work, we summarize the first results on this way. We discuss the specificity of the geoelectrical models in the problems of mining prospecting for ore bodies. The state-of-the-art capabilities of the method, which rely on the synchronous observation systems and the procedure of joint inversion of magnetotelluric and magnetovariational responses, are considered in the context of ore mineral exploration. The results of modeling a typical mining audio-magnetotelluric survey for ore minerals are presented. On the basis of these simulations and the data provided by in-situ soundings, the efficient approaches to the processing, analysis, and inversion of these data are discussed and illustrated. The future trends in magnetotellurics as applied to the mining prospecting are analyzed.

Potential for cobalt recovery from lateritic ores in Europe

NASA Astrophysics Data System (ADS)

Herrington, R.

2012-04-01

Cobalt is one of the 'critical metals' identified under the EU Raw Materials Initiative. Annually the global mine production of cobalt is around 55,000 tonnes,with Europe's industries consuming around 30% of that figure. Currently Europe produces around 27 tonnes of cobalt from mines in Finland although new capacity is planned. Co-bearing nickel laterite ores being mined in Greece, Macedonia and Kosovo where the cobalt is currently not being recovered (ores have typical analyses of 0.055% Co and >1% Ni,). These ores are currently treated directly in pyrometallurgical plants to recover the contained nickel and this process means there is no separate cobalt product produced. Hydrometallurgical treatment of mineralogically suitable laterite ores can recover the cobalt; for example Cuba recovers 3,500 tonnes of cobalt from its laterite mining operations, which are of a similar scale to the current European operations. Implementation of hydrometallurgical techniques is in its infancy in Europe with one deposit in Turkey planning to use atmospheric heap leaching to recover nickel and copper from oxide-dominated ores. More widespread implementation of these methods to mineralogically suitable ore types could unlock the highly significant undeveloped resources (with metal contents >0.04% Co and >1% Ni), which have been defined throughout the Balkans eastwards into Turkey. At a conservative estimate, this region has the potential to supply up to 30% of the EU cobalt requirements.

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions...

40 CFR 440.10 - Applicability; description of the iron ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ore subcategory. 440.10 Section 440.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.10 Applicability; description of the iron ore subcategory. The provisions of...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The...

40 CFR 440.10 - Applicability; description of the iron ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ore subcategory. 440.10 Section 440.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.10 Applicability; description of the iron ore subcategory. The provisions of...

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... titanium ore subcategory. 440.50 Section 440.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.50 Applicability; description of the titanium ore subcategory. The...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The...

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The...

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... titanium ore subcategory. 440.50 Section 440.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.50 Applicability; description of the titanium ore subcategory. The...

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions...

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... titanium ore subcategory. 440.50 Section 440.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.50 Applicability; description of the titanium ore subcategory. The...

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions...

40 CFR 440.10 - Applicability; description of the iron ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ore subcategory. 440.10 Section 440.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.10 Applicability; description of the iron ore subcategory. The provisions of...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions...

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The...

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions...

Occurrence of silver minerals in a silver-rich pocket in the massive sulfide zinc-lead ores in the Edwards mine, New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serviss, C.R.; Grout, C.M.; Hagni, R.D.

1985-01-01

Ore microscopic examination of uncommon silver-rich ores from the Edwards mine has detected three silver minerals, native silver, freibergite, and argentite, that were previously unreported in the literature from the Balmat-Edwards district. The zinc-lead ore deposits of the Balmat-Edwards District in northern New York are composed of very coarse-grained massive sulfides, principally sphalerite, galena, and pyrite. The typical ores contain small amounts of silver in solid solution galena. Galena concentrates produced from those ores have contained an average of 15 ounces of silver per ton of 60% lead concentrates. In contrast to the typical ore a silver-rich pocket, that measuredmore » three feet by three feet on the vertical mine face and was the subject of this study, contained nearly 1% silver in a zinc ore. Ore microscopic study shows that this ore is especially characterized by abundant, relatively fine-grained chalcopyrite with anhedral pyrite inclusions. Fine-grained sphalerite, native silver, argentite, freibergite and arsenopyrite occur in association with the chalcopyrite and as fracture-fillings in gangue minerals. Geochemically anomalous amounts of tin, barium, chromium, and nickel also are present in the silver-rich pocket. The silver-rich pocket may mark the locus of an early feeder vent or alternatively it may record a hydrothermal event that was superimposed upon the event responsible for the metamorphic ore textures.« less

Chromite Ore from the Transvaal Region of South Africa

EPA Pesticide Factsheets

In 2001, EPA finalized a rule to to delete both chromite ore mined in the Transvaal Region of South Africa and the unreacted ore component of the chromite ore processing residue (COPR) from TRI reporting requirements.

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) mills beneficiating titanium ores by electrostatic methods, magnetic and physical methods, or flotation methods; and (c) mines engaged in the dredge mining of placer deposits of sands containing rutile... methods in conjunction with electrostatic or magnetic methods). ...

Reduced mortality rates in a cohort of long-term underground iron-ore miners.

PubMed

Björ, Ove; Jonsson, Håkan; Damber, Lena; Wahlström, Jens; Nilsson, Tohr

2013-05-01

Historically, working in iron-ore mines has been associated with an increased risk of lung cancer and silicosis. However, studies on other causes of mortality are inconsistent and in the case of cancer incidence, sparse. The aim of this study was to examine the association between iron-ore mining, mortality and cancer incidence. A 54-year cohort study on iron-ore miners from mines in northern Sweden was carried out comprising 13,000 workers. Standardized rate ratios were calculated comparing the disease frequency, mortality, and cancer incidence with that of the general population of northern Sweden. Poisson regression was used to evaluate the association between the durations of employment and underground work, and outcome. Underground mining was associated with a significant decrease in adjusted mortality rate ratios for cerebrovascular and digestive system diseases, and stroke. For several outcomes, elevated standardized rate ratios were observed among blue-collar workers relative to the reference population. However, only the incidence of lung cancer increased with employment time underground (P < 0.001). Long-term iron-ore mining underground was associated with lower rates regarding several health outcomes. This is possibly explained by factors related to actual job activities, environmental exposure, or the selection of healthier workers for long-term underground employment. Copyright © 2013 Wiley Periodicals, Inc.

Lead and zinc dust depositions from ore trains characterised using lead isotopic compositions.

PubMed

Kristensen, L J; Taylor, M P; Morrison, A L

2015-03-01

This study investigates an unusual source of environmental lead contamination - the emission and deposition of lead and zinc concentrates along train lines into and out of Australia's oldest silver-lead-zinc mine at Broken Hill, Australia. Transport of lead and zinc ore concentrates from the Broken Hill mines has occurred for more than 125 years, during which time the majority was moved in uncovered rail wagons. A significant amount of ore was lost to the adjoining environments, resulting in soil immediately adjacent to train lines elevated with concentrations of lead (695 mg kg(-1)) and zinc (2230 mg kg(-1)). Concentrations of lead and zinc decreased away from the train line and also with depth shown in soil profiles. Lead isotopic compositions demonstrated the soil lead contained Broken Hill ore in increasing percentages closer to the train line, with up to 97% apportioned to the mined Broken Hill ore body. SEM examination showed ceiling dusts collected from houses along the train line were composed of unweathered galena particles, characteristic of the concentrate transported in the rail wagons. The loss of ore from the uncovered wagons has significantly extended the environmental footprint of contamination from local mining operations over an area extending hundreds of kilometres along each of the three train lines.

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The provisions of this...

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this...

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The provisions of this...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions of this subpart...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The provisions of this...

40 CFR 440.60 - Applicability; description of the tungsten ore subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... tungsten ore subcategory. 440.60 Section 440.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.60 Applicability; description of the tungsten ore subcategory. The provisions of this...

40 CFR 440.90 - Applicability; description of the antimony ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... antimony ore subcategory. 440.90 Section 440.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.90 Applicability; description of the antimony ore subcategory. The provisions of this...

40 CFR 440.70 - Applicability; description of the nickel ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... nickel ore subcategory. 440.70 Section 440.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.70 Applicability; description of the nickel ore subcategory. The provisions of this subpart...

40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions of subpart D...

40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... aluminum ore subcategory. 440.20 Section 440.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.20 Applicability; description of the aluminum ore subcategory. The provisions of this...

40 CFR 440.50 - Applicability; description of the titanium ore subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... titanium ore subcategory. 440.50 Section 440.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.50 Applicability; description of the titanium ore subcategory. The provisions of this...

Investigation of mine and industry dumps in the FRG in relation to a possible release of natural radioactive elements.

PubMed

Schmitz, J

1985-10-01

More than 350 dumps of mines and industries in two federal states of the FRG were recorded, measured radiometrically, evaluated, and some of them sampled. Most of the mine dumps belonged to old and smaller residues from lead/zinc and iron ore mining, while the largest depositions contain tailings of modern ore beneficiation or flyash disposal. All mine dumps from uranium exploration in Baden-Württemberg and Bavaria were investigated. The highest doses, up to 100 mSv/a, were found on the piles of the uranium exploration. These depositions, which are supervised and licensed, are followed, in terms of surface dose, by the old uncontrolled mine dumps of silver/cobalt mining with doses up to 20 mSv/a. The numerous porphyry and granite quarries show doses between 1 and 2 mSv/a, as do flyash and slag dumps. The lowest doses were found on the dumps of the hydrothermal Pb/Zn and iron ore deposits, while the slag piles of iron ore processing showed higher thorium values. Assays for Ra-226 and Pb-210 of the materials deposited confirmed the radiometric results. Analyses of seepage waters and gallery waters showed only very few values exceeding the derived drinking water concentrations.

Earth observation taken by the Expedition 11 crew

NASA Image and Video Library

2005-06-25

ISS011-E-09620 (26 June 2005) --- Grasberg Mine, Indonesia is featured in this image photographed by an Expedition 11 crewmember on the International Space Station. Located in the Sudirman Mountains of the Irian Jaya province of Indonesia, the Grasberg complex (also known as the Freeport Mine) is one of the largest gold and copper mining operations in the world. The Sudirman Mountains form the western portion of the Maoke Range that extend across Irian Jaya from west to the east-southeast. According to scientists, these ranges were formed by ongoing collision of the northward-moving Australian and westward-moving Pacific tectonic plates. Intrusion of hot magma into sedimentary rock layers during uplift of the mountains resulted in the formation of copper- and gold-bearing ore bodies. Rich copper ore bodies were discovered in the area in 1936, and the Grasberg gold-bearing ore bodies were discovered in 1988. This image illustrates the approximately 4 kilometers-wide open-pit portion of the mine complex; there are also extensive underground mine workings. Access roads for trucks hauling ore and waste rock are visible along the sides of the pit.

40 CFR 440.81 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.81 Section 440.81 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a...

40 CFR 440.81 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.81 Section 440.81 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct...

40 CFR 440.81 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.81 Section 440.81 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a...

40 CFR 440.81 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.81 Section 440.81 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a Byproduct...

40 CFR 440.81 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.81 Section 440.81 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory (Mined Alone and Not as a...

Sustainable rehabilitation of mining waste and acid mine drainage using geochemistry, mine type, mineralogy, texture, ore extraction and climate knowledge.

PubMed

Anawar, Hossain Md

2015-08-01

The oxidative dissolution of sulfidic minerals releases the extremely acidic leachate, sulfate and potentially toxic elements e.g., As, Ag, Cd, Cr, Cu, Hg, Ni, Pb, Sb, Th, U, Zn, etc. from different mine tailings and waste dumps. For the sustainable rehabilitation and disposal of mining waste, the sources and mechanisms of contaminant generation, fate and transport of contaminants should be clearly understood. Therefore, this study has provided a critical review on (1) recent insights in mechanisms of oxidation of sulfidic minerals, (2) environmental contamination by mining waste, and (3) remediation and rehabilitation techniques, and (4) then developed the GEMTEC conceptual model/guide [(bio)-geochemistry-mine type-mineralogy- geological texture-ore extraction process-climatic knowledge)] to provide the new scientific approach and knowledge for remediation of mining wastes and acid mine drainage. This study has suggested the pre-mining geological, geochemical, mineralogical and microtextural characterization of different mineral deposits, and post-mining studies of ore extraction processes, physical, geochemical, mineralogical and microbial reactions, natural attenuation and effect of climate change for sustainable rehabilitation of mining waste. All components of this model should be considered for effective and integrated management of mining waste and acid mine drainage. Copyright © 2015 Elsevier Ltd. All rights reserved.

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this subpart K are applicable to discharges from (a) mines that produce platinum ore and (b...

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this subpart K are applicable to discharges from (a) mines that produce platinum ore and (b...

40 CFR 440.110 - Applicability; description of the platinum ore subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... platinum ore subcategory. 440.110 Section 440.110 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Platinum Ores Subcategory § 440.110 Applicability; description of the platinum ore subcategory. The provisions of this subpart K are applicable to discharges from (a) mines that produce platinum ore and (b...

A mineralogical perspective on the recovery of platinum group elements from Merensky Reef and UG2 at the Two Rivers mine on the Eastern limb of the Bushveld Complex in South Africa

NASA Astrophysics Data System (ADS)

Rose, Derek H.; Viljoen, K. S.; Mulaba-Bafubiandi, Antoine

2018-06-01

Published studies dealing with the process mineralogy of Pt mines on the Bushveld Complex is generally limited to the Western Bushveld. The recognition by mine management that another resource, in addition to the Upper Group 2 (UG2) reef currently being mined at the Two Rivers platinum mine (TRP), is urgently required in order to extend the life of mine, presented an opportunity to conduct such a study on the Eastern Limb of the Bushveld Complex. A process mineralogical investigation was undertaken on ore from the Merensky Reef (MR) and the UG2 at TRP. This was conducted on a suite of geological samples (channel samples) collected from the underground workings, as well as metallurgical samples obtained from the rougher circuits at the concentrator plant during the processing of MR and UG2 ore. The geological and metallurgical samples were analysed for bulk composition and quantitative mineralogy, while the geological samples were also subjected to laboratory-scale milling and flotation tests. This study shows that, although mineralogically distinct, the MR and UG2 behave similarly in terms of metallurgical performance. This holds promise for the proposed blending of MR and UG2 ores at TRP. An evaluation of the bulk rock (ore) Pt/Pd ratio as a possible indicator of the level of hydrothermal alteration of the ore, demonstrates that this may be of use in predicting recovery plant performance.

Lithium

USGS Publications Warehouse

Ober, J.

1998-01-01

The lithium industry can be divided into two sectors: ore concentrate producers and chemical producers. Ore concentrate producers mine lithium minerals. They beneficiate the ores to produce material for use in ceramics and glass manufacturing.

Safeguards on uranium ore concentrate? the impact of modern mining and milling process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Francis, Stephen

2013-07-01

Increased purity in uranium ore concentrate not only raises the question as to whether Safeguards should be applied to the entirety of uranium conversion facilities, but also as to whether some degree of coverage should be moved back to uranium ore concentrate production at uranium mining and milling facilities. This paper looks at uranium ore concentrate production across the globe and explores the extent to which increased purity is evident and the underlying reasons. Potential issues this increase in purity raises for IAEA's strategy on the Starting Point of Safeguards are also discussed.

Antimony ore in the Fairbanks district, Alaska

USGS Publications Warehouse

Killeen, Pemberton Lewis; Mertie, John B.

1951-01-01

Antimony-bearing ores in the Fairbanks district, Alaska, are found principally in two areas, the extremities of which are at points 10 miles west and 23 miles northeast of Fairbanks; and one of two minor areas lies along this same trend 30 miles farther to the northeast. These areas are probably only local manifestations of mineralization that affected a much broader area and formed antimony-bearing deposits in neighboring districts, the closest of which is 50 miles away. The ores were exposed largely as a result of lode gold mining, but at two periods in the past, high prices for antimony ore warranted an independent production and about 2500 tons of stibnite ore was shipped. The sulfide deposits occupy the same fractures along which a gold-quartz mineralization of greater economic importance occurred; and both are probably genetically related to igneous rocks which intrude the schistose country rock. The sulfide is in part contemporaneous with some late-stage quartz in which it occurs as disseminated crystals; and in part the latest filling in the mineralized zones where it forms kidney-shaped masses of essentially solid sulfide. One extremely long mass must have contained nearly 100 tons of ore, but the average of the larger kidneys is closer to several tons. Much of the ore is stibnite, with quartz as a minor impurity, and assays show the tenor to vary from 40 to 65 percent antimony. Sulphantimonites are less abundant but likewise occur as disseminated crystals and as kidney-shaped bodies. Antimony oxides appear on the weathered surface and along fractures within the sulfide ore. Deposits containing either stibnite or sulphantimonite are known at more than 50 localities, but only eighteen have produced ore and the bulk of this came from the mines. The geology of the deposit, and the nature, extent, and period of the workings are covered in the detailed descriptions of individual occurrences. Several geologic and economic factors, which greatly affect prospecting and mining for stibnite ore in the area, are outlined. The principal available ore and reserves are considered to be ores earlier mined but never shipped, ore minable from near-surface deposits, and ores recoverable as a by-product of future gold mining. The outlook for stibnite production in the district is very uncertain. Apparently the greater portion of stibnite ore has already been recovered and present operations will strip the two principal areas of the district. This conclusion is based on the scanty discoveries since the last war and the fact that the areas are so pock-marked with prospects that there is little likelihood that any other large near-surface bodies remain to be discovered. Future prospecting would essentially be limited to attempts to seek the continuation of lodes previously having high yields of stibnite.

Analytical Fingerprint of Wolframite Ore Concentrates.

PubMed

Gäbler, Hans-Eike; Schink, Wilhelm; Goldmann, Simon; Bahr, Andreas; Gawronski, Timo

2017-07-01

Ongoing violent conflicts in Central Africa are fueled by illegal mining and trading of tantalum, tin, and tungsten ores. The credibility of document-based traceability systems can be improved by an analytical fingerprint applied as an independent method to confirm or doubt the documented origin of ore minerals. Wolframite (Fe,Mn)WO 4 is the most important ore mineral for tungsten and is subject to artisanal mining in Central Africa. Element concentrations of wolframite grains analyzed by laser ablation-inductively coupled plasma-mass spectrometry are used to establish the analytical fingerprint. The data from ore concentrate samples are multivariate, not normal or log-normal distributed. The samples cannot be regarded as representative aliquots of a population. Based on the Kolmogorov-Smirnov distance, a measure of similarity between a sample in question and reference samples from a database is determined. A decision criterion is deduced to recognize samples which do not originate from the declared mine site. © 2017 American Academy of Forensic Sciences.

Applied technology for mine waste water decontamination in the uranium ores extraction from Romania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bejenaru, C.; Filip, G.; Vacariu, V.T.

1996-12-31

The exploitation of uranium ores in Romania is carried out in underground mines. In all exploited uranium deposits, mine waste waters results and will still result after the closure of uranium ore extraction activity. The mine waters are radioactively contaminated with uranium and its decay products being a hazard both for underground waters as for the environment. This paper present the results of research work carried out by authors for uranium elimination from waste waters as the problems involved during the exploitation process of the existent equipment as its maintenance in good experimental conditions. The main waste water characteristics aremore » discussed: solids as suspension, uranium, radium, mineral salts, pH, etc. The moist suitable way to eliminate uranium from mine waste waters is the ion exchange process based on ion exchangers in fluidized bed. A flowsheet is given with main advantages resulted.« less

Mines and Prospects, Idaho Springs District, Clear Creek and Gilpin Counties, Colorado - Descriptions and Maps

USGS Publications Warehouse

Moench, Robert Hadley; Drake, Avery Ala

1966-01-01

The Idaho Springs mining district forms an important segment of the Front Range mineral belt, a northeast-trending zone of coextensive intrusive rocks and hydrothermal ore deposits of early Tertiary age. This belt, which is about 50 miles long, extends from the region just west of Boulder southwestward across the Front Range. From 1859, when placer gold was discovered in Idaho Springs and lode gold in Central City, through 1959, ores valued at about $200 million were shipped from a 50-square-mile area that includes the Idaho Springs and adjacent districts to the north, west, and southwest. The adjacent Central City district, which produced ores valued at more than $100 million, is clearly the most important district in the mineral belt. The Idaho Springs district from 1860 to 1959 produced ores valued at about $65 million, and the districts to the west and southwest produced smaller amounts. Gold has accounted for about 60 percent of the value of the ore, but in some areas silver provides the chief values, and copper, lead, and zinc add value to the ores in most areas. Mining activity in the Idaho Springs and adjacent districts was at its 'heyday' in the late 1800's, it declined sharply after 1914, it was somewhat renewed during the 1930's, and it greatly declined during World War II. In the 1950's uranium prospecting stimulated some mining activity. No uranium was produced, however, and at the close of the decade only one mine--the Bald Eagle--was being worked for its precious- and base-metal ores. In this report, 135 mines and prospects are described. The mines and prospects described are those that were accessible at the time of this study, as well as a few inaccessible properties for which some information was available. Most of the data for the inaccessible or unimportant properties were obtained from Bastin and Hill (1917) and Spurr, Garrey, and Ball (1908). The following list shows, in alphabetical order, the names of about 325 openings of mines and prospects, their coordinate location on the district map (fig. 1), the page of this report on which their description starts, and the number of the illustration, if any, referring to them.

Mining for metals in society's waste

USGS Publications Warehouse

Smith, Kathleen S.; Plumlee, Geoffrey S.; Hageman, Philip L.

2015-01-01

Metals and minerals are natural resources that human beings have been mining for thousands of years. Contemporary metal mining is dominated by iron ore, copper and gold, with 2 billion tons of iron ore, nearly 20 million tons of copper and 2,000 tons of gold produced every year. Tens to hundreds of tons of other metals that are essential components for electronics, green energy production, and high-technology products are produced annually.

The influence of geomorphology on the role of women at artisanal and small-scale mine sites

USGS Publications Warehouse

Malpeli, Katherine C.; Chirico, Peter G.

2013-01-01

The geologic and geomorphic expressions of a mineral deposit determine its location, size, and accessibility, characteristics which in turn greatly influence the success of artisans mining the deposit. Despite this critical information, which can be garnered through studying the surficial physical expression of a deposit, the geologic and geomorphic sciences have been largely overlooked in artisanal mining-related research. This study demonstrates that a correlation exists between the roles of female miners at artisanal diamond and gold mining sites in western and central Africa and the physical expression of the deposits. Typically, women perform ore processing and ancillary roles at mine sites. On occasion, however, women participate in the extraction process itself. Women were found to participate in the extraction of ore only when a deposit had a thin overburden layer, thus rendering the mineralized ore more accessible. When deposits required a significant degree of manual labour to access the ore due to thick overburden layers, women were typically relegated to other roles. The identification of this link encourages the establishment of an alternative research avenue in which the physical and social sciences merge to better inform policymakers, so that the most appropriate artisanal mining assistance programs can be developed and implemented.

Geology and mineral deposits of the Minnie Moore and Bullion mineralized areas, Blaine County, Idaho

USGS Publications Warehouse

Link, Paul Karl; Worl, Ronald G.

2001-01-01

In the early 1880?s the discovery of rich ores in the Minnie Moore and Bullion mineralized areas sparked a rush to settle and develop the Wood River valley. Silver and lead discoveries in these areas spurred the boom in mining after completion of the Oregon Short Line Railroad to Hailey in 1883. In both areas the ore comprises galena, sphalerite, and tetrahedrite in a gangue of siderite, calcite, or quartz. Minor goldbearing quartz veins are also present. The ore is in fissure and replacement veins along fracture systems that formed in Late Cretaceous time, after intrusion of nearby granodiorite or quartz diorite stocks. The ore formed under mesothermal conditions and heat was supplied by the nearby plutons. In the Minnie Moore area, the mineralized veins are cut by low-angle normal faults that are of probable Eocene age. In the Minnie Moore mineralized area, the host rock is the middle part of the Devonian Milligen Formation, (the informal Lucky Coin limestone and Triumph argillite), which is the same stratigraphic level as the host ore in the rich Triumph mine northeast of Hailey. In the Bullion mineralized area, the ore is hosted by the lower member of the Middle Pennsylvanian to Lower Permian Dollarhide Formation. Rich ore was mined in several tunnels that reached the Mayflower vein, a northwest-striking mineralized shear zone. The deposits are thought to be mainly mesothermal veins that formed in association with Cretaceous magmatism. The syngenetic stratiform model of ore formation has often been applied to these deposits, however, no evidence of syngenetic mineralization was found in this study. Faulting has displaced most of the major orebodies and thus has made mining these deposits a challenge.

An Effective Belt Conveyor for Underground Ore Transportation Systems

NASA Astrophysics Data System (ADS)

Krol, Robert; Kawalec, Witold; Gladysiewicz, Lech

2017-12-01

Raw material transportation generates a substantial share of costs in the mining industry. Mining companies are therefore determined to improve the effectiveness of their transportation system, focusing on solutions that increase both its energy efficiency and reliability while keeping maintenance costs low. In the underground copper ore operations in Poland’s KGHM mines vast and complex belt conveyor systems have been used for horizontal haulage of the run-of-mine ore from mining departments to shafts. Basing upon a long-time experience in the field of analysing, testing, designing and computing of belt conveyor equipment with regard to specific operational conditions, the improvements to the standard design of an underground belt conveyor for ore transportation have been proposed. As the key elements of a belt conveyor, the energy-efficient conveyor belt and optimised carrying idlers have been developed for the new generation of underground conveyors. The proposed solutions were tested individually on the specially constructed test stands in the laboratory and in the experimental belt conveyor that was built up with the use of prototype parts and commissioned for the regular ore haulage in a mining department in the KGHM underground mine “Lubin”. Its work was monitored and the recorded operational parameters (loadings, stresses and strains, energy dissipation, belt tracking) were compared with those previously collected on a reference (standard) conveyor. These in-situ measurements have proved that the proposed solutions will return with significant energy savings and lower maintenance costs. Calculations made on the basis of measurement results in the specialized belt conveyor designing software allow to estimate the possible savings if the modernized conveyors supersede the standard ones in a large belt conveying system.

Reagents and fractions impact on sulphide ore heap bioleaching at Smolnik mine

NASA Astrophysics Data System (ADS)

Oros, L. M.; Zavada, J.

2017-10-01

Mine Smolnik is one of the oldest sulphide ore mines in Europe and it is also an important part of bioleaching development. This paper follows previous attempts to extract residual metals from nearby heaps via variations in bioleaching reagents with regard to recent findings and needs in the related industry. Furthermore, economic and process relations between reagents and chosen heap fractions were also investigated in this case study.

40 CFR 440.30 - Applicability; description of the uranium, radium and vanadium ores subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... uranium, radium and vanadium ores subcategory. 440.30 Section 440.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.30 Applicability; description of the...

Interaction of mining activities and aquatic environment: A review from Greek mine sites.

NASA Astrophysics Data System (ADS)

Vasileiou, Eleni; Kallioras, Andreas

2016-04-01

In Greece a significant amount of mineral and ore deposits have been recorded accompanied by large industrial interest and a long mining history. Today many active and/or abandoned mine sites are scattered within the country; while mining activities take place in different sites for exploiting various deposits (clay, limestone, slate, gypsum, kaolin, mixed sulphide ores (lead, zinc, olivine, pozzolan, quartz lignite, nickel, magnesite, aluminum, bauxite, gold, marbles etc). The most prominent recent ones are: (i) the lignite exploitation that is extended in the area of Ptolemais (Western Macedonia) and Megalopolis (Central Peloponnese); and (ii) the major bauxite deposits located in central Greece within the Parnassos-Ghiona geotectonic zone and on Euboea Island. In the latter area, significant ores of magnesite were exploited and mixed sulphide ores. Centuries of intensive mining exploitation and metallurgical treatment of lead-silver deposits in Greece, have also resulted in significant abandoned sites, such as the one in Lavrion. Mining activities in Lavrio, were initiated in ancient times and continued until the 1980s, resulting in the production of significant waste stockpiles deposited in the area, crucial for the local water resources. Ιn many mining sites, environmental pressures are also recorded after the mine closure to the aquatic environment, as the surface waters flow through waste dump areas and contaminated soils. This paper aims to the geospatial visualization of the mining activities in Greece, in connection to their negative (surface- and/or ground-water pollution; overpumping due to extensive dewatering practices) or positive (enhanced groundwater recharge; pit lakes, improvement of water budget in the catchment scale) impacts on local water resources.

26 CFR 1.381(c)(10)-1 - Deferred exploration and development expenditures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... expenditures made in connection with any ore, mineral, mine, or other natural deposit transferred to the..., Y Corporation sells 150,000 units of produced ore benefited by the development expenditures incurred... respect of a mine or other natural deposit which it subsequently disposes of except for a retained...

26 CFR 1.381(c)(10)-1 - Deferred exploration and development expenditures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... expenditures made in connection with any ore, mineral, mine, or other natural deposit transferred to the..., Y Corporation sells 150,000 units of produced ore benefited by the development expenditures incurred... respect of a mine or other natural deposit which it subsequently disposes of except for a retained...

40 CFR 440.34 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... underground, that produce uranium ore, excluding mines using in situ leach methods, shall not exceed: Effluent... leach process for the extraction of uranium or from mines and mills using in situ leach methods. The... Vanadium Ores Subcategory § 440.34 New source performance standards (NSPS). Except as provided in subpart L...

40 CFR 440.34 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... underground, that produce uranium ore, excluding mines using in situ leach methods, shall not exceed: Effluent... leach process for the extraction of uranium or from mines and mills using in situ leach methods. The... Vanadium Ores Subcategory § 440.34 New source performance standards (NSPS). Except as provided in subpart L...

40 CFR 440.34 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... underground, that produce uranium ore, excluding mines using in situ leach methods, shall not exceed: Effluent... leach process for the extraction of uranium or from mines and mills using in situ leach methods. The... Vanadium Ores Subcategory § 440.34 New source performance standards (NSPS). Except as provided in subpart L...

40 CFR 440.104 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

..., in-situ leach or vat-leach processes to extract copper from ores or ore waste materials. The Agency... provided in subpart L of this part any new source subject to this subsection must achieve the following... demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines that...

40 CFR 440.104 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

..., in-situ leach or vat-leach processes to extract copper from ores or ore waste materials. The Agency... provided in subpart L of this part any new source subject to this subsection must achieve the following... demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines that...

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

40 CFR 440.100 - Applicability; description of the copper, lead, zinc, gold, silver, and molybdenum ores subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... process alone or in conjunction with other processes, for the beneficiation of copper, lead, zinc, gold, silver, or molybdenum ores, or any combination of these ores; (3) Mines and mills that use dump, heap, in-situ leach, or vat-leach processes to extract copper from ores or ore waste materials; and (4) Mills...

Sodium cyanide hazards to fish and other wildlife from gold mining operations

USGS Publications Warehouse

Eisler, R.; Clark, D.R.; Wiemeyer, Stanley N.; Henny, C.J.; Azcue, Jose M.

1999-01-01

Highly toxic sodium cyanide (NaCN) is used increasingly by the international mining community to extract gold and other precious metals through milling of high grade ores and heap leaching of low grade ores. Of the 98 million kg cyanide (CN) consumed in North America in 1989, about 80% was used in gold mining (Knudson 1990). In Canada, more than 90% of the mined gold is extracted from ores with the cyanidation process. This process consists of leaching gold from the ore as a gold-cyanide complex, and gold being recovered by precipitation (Simovic and Snodgrass 1985). Milling and heap leaching require cycling of millions of liters of alkaline water containing high concentrations of potentially toxic NaCN, free cyanide, and metal cyanide complexes that are frequently accessible to wildlife. Some milling operations result in tailings ponds of 150 ha and larger. Heap leach operations that spray or drip cyanide solution onto the flattened top of the ore heap require solution processing ponds of about 1 ha in surface area. Although not intentional or desired, puddles of various sizes may occur on the top of heaps where the highest concentrations of NaCN are found. Exposed solution recovery channels are usually constructed at the base of leach heaps. All of these cyanidecontaining water bodies are hazardous to wildlife if not properly managed (Henny et al. 1994). In this account we emphasize hazards of cyanide from mining operations to fish and wildlife species and proposed mitigation to protect them.

Potential ecological and human health risks of heavy metals in surface soils associated with iron ore mining in Pahang, Malaysia.

PubMed

Diami, Siti Merryan; Kusin, Faradiella Mohd; Madzin, Zafira

2016-10-01

The composition of heavy metals (and metalloid) in surface soils of iron ore mine-impacted areas has been evaluated of their potential ecological and human health risks. The mining areas included seven selected locations in the vicinity of active and abandoned iron ore-mining sites in Pahang, Malaysia. Heavy metals such as Fe, Mn, Cu, Zn, Co, Pb, Cr, Ni, and Cd and metalloid As were present in the mining soils of the studied area, while Cu was found exceeding the soil guideline value at all sampling locations. However, the assessment of the potential ecological risk index (RI) indicated low ecological risk (RI between 44 and 128) with respect to Cd, Pb, Cu, As, Zn, Co, and Ni in the surface soils. Contributions of potential ecological risk [Formula: see text]by metal elements to the total potential ecological RI were evident for Cd, As, Pb, and Cu. Contribution of Cu appears to be consistently greater in the abandoned mining area compared to active iron ore-mining site. For non-carcinogenic risk, no significant potential health risk was found to both children and adults as the hazard indices (HIs) were all below than 1. The lifetime cancer risk (LCR) indicated that As has greater potential carcinogenic risk compared to other metals that may induce carcinogenic effects such as Pb, Cr, and Cd, while the LCR of As for children fell within tolerable range for regulatory purposes. Irrespective of carcinogenic or non-carcinogenic risk, greater potential health risk was found among children (by an order of magnitude higher for most metals) compared to adults. The hazard quotient (HQ) and cancer risk indicated that the pathways for the risk to occur were found to be in the order of ingestion > dermal > inhalation. Overall, findings showed that some metals and metalloid were still present at comparable concentrations even long after cessation of the iron ore-mining activities.

Transformation and contamination of soils in iron ore mining areas (a review)

NASA Astrophysics Data System (ADS)

Zamotaev, I. V.; Ivanov, I. V.; Mikheev, P. V.; Belobrov, V. P.

2017-03-01

Current concepts of soil transformation and contamination in iron ore mining areas have been reviewed. Changes of soils and ecosystems in the mining areas are among the largest-scale impacts of economic activity on the nature. Regularities in the radial differentiation, spatial distribution, and accumulation of heavy metals in soils of different natural zones are analyzed. The effects of mining technogenesis and gas-dust emissions from enterprises on soil microbial communities and fauna are considered. In zones of longterm atmotechnogenic impact of mining and processing plants, the stable state of ecosystems is lost and/or a new technoecosystem different from the natural one, with own microbial cenosis, is formed, where communities of soil organisms are in the stress state. In the ore mining regions, embriozems are formed, which pass through specific stages of technogenically-determined development, as well as technosols, chemozems, and technogenic surface formations with variable material compositions and properties. Technogenic soils and soil-like bodies form a soil cover differing from the initial one, whose complexity and contrast are not related to the natural factors of differentiation.

8. EAST ELEVATION OF SKIDOO MILL AND UPPER ORE BIN, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. EAST ELEVATION OF SKIDOO MILL AND UPPER ORE BIN, LOOKING WEST FROM ACCESS ROAD. THE ROADWAY ON THIS LEVEL (CENTER) WAS USED FOR UNLOADING ORE BROUGHT ON BURROWS INTO THE ORE BIN AT THE TOP LEVEL OF THE MILL. THE ORE BIN IN THE UPPER LEFT WAS ADDED LATER WHEN ORE WAS BROUGHT TO THE MILL BY TRUCKS. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

Assessment of (222)Rn emanation from ore body and backfill tailings in low-grade underground uranium mine.

PubMed

Mishra, Devi Prasad; Sahu, Patitapaban; Panigrahi, Durga Charan; Jha, Vivekanand; Patnaik, R Lokeswara

2014-02-01

This paper presents a comparative study of (222)Rn emanation from the ore and backfill tailings in an underground uranium mine located at Jaduguda, India. The effects of surface area, porosity, (226)Ra and moisture contents on (222)Rn emanation rate were examined. The study revealed that the bulk porosity of backfill tailings is more than two orders of magnitude than that of the ore. The geometric mean radon emanation rates from the ore body and backfill tailings were found to be 10.01 × 10(-3) and 1.03 Bq m(-2) s(-1), respectively. Significant positive linear correlations between (222)Rn emanation rate and the (226)Ra content of ore and tailings were observed. For normalised (226)Ra content, the (222)Rn emanation rate from tailings was found to be 283 times higher than the ore due to higher bulk porosity and surface area. The relative radon emanation from the tailings with moisture fraction of 0.14 was found to be 2.4 times higher than the oven-dried tailings. The study suggested that the mill tailings used as a backfill material significantly contributes to radon emanation as compared to the ore body itself and the (226)Ra content and bulk porosity are the dominant factors for radon emanation into the mine atmosphere.

Economic geology of the Central City district, Gilpin County, Colorado

USGS Publications Warehouse

Sims, P.K.; Drake, Avery A.; Tooker, E.W.

1963-01-01

The Central City district, in Gilpin County, Colo., is on the east flank of the Front Range, about 30 miles west of Denver. The district is the most important mining camp in the Front Range mineral belt, and has yielded more than $100 million worth of gold, silver, uranium, and base-metal ores since 1859. Gold accounts for about 85 percent of the dollar value of the ore. In recent years mining activity has been slack but from 1950 to 1955 the search for uranium ores stimulated prospecting and development.

Idea of Identification of Copper Ore with the Use of Process Analyser Technology Sensors

NASA Astrophysics Data System (ADS)

Jurdziak, Leszek; Kaszuba, Damian; Kawalec, Witold; Król, Robert

2016-10-01

The Polish resources of the copper ore exploited by the KGHM S.A. underground mines are considered as one of the most complex in the world and - consequently - the most difficult to be processed. The ore consists of three lithology forms: dolomites, shales and sandstones but in different proportions which has a significant impact on the effectiveness of the grinding and flotation processes. The lithological composition of the ore is generally recognised in-situ but after being mined it is blended on its long way from various mining fields to the processing plant by the complex transportation system consisting of belt conveyors with numerous switching points, ore bunkers and shafts. Identification of the lithological composition of the ore being supplied to the processing plant should improve the adjustments of the ore processing machinery equipment aiming to decrease the specific processing (mainly grinding) energy consumption as well as increase the metal recovery. The novel idea of Process Analyser Technology (PAT) sensors - information carrying pellets, dropped into the transported or processed bulk material which can be read directly when needed - is investigated for various applications within the DISIRE project (a part of the SPIRE initiative, acting under the Horizon2020 framework program) and here is adopted for implementing the annotation the transported copper ore for the needs of ore processing plants control. The identification of the lithological composition of ore blended on its way to the processing plant can be achieved by an information system consisting of pellets that keep the information about the original location of the portions of conveyed ore, the digital, geological database keeping the data of in-situ lithology and the simulation models of the transportation system, necessary to evaluate the composition of the blended ore. The assumptions of the proposed solution and the plan of necessary in-situ tests (with the special respect to harsh environment of

A report on the medieval mining and ore processing complex: Zilan valley, Van, Turkey.

NASA Astrophysics Data System (ADS)

Ateş, Yusuf; Kılıη, Sinan

Literature has records of the use of obsidian that shows the existence of a knowledge base on raw material resources around Lake Van extending to very ancient times. Against this background, very little information can be obtained from literature about accurate location of historical mining activities in the region today. An ancient mining and processing complex, located northwest of the city of Van (Turkey) has been discovered by chance in 2007. The purpose of this article is to describe this historical mining area. The site contains mining structures such as shafts and galleries, and heaves of stone chips indicating some ore enrichment activities taking place there. The XRD and chemical analyses show the samples taken from the ore vein are rich in Manganese (Mn) and Barium (Ba), and it is concluded that the Zilan Valley Mining and Processing Complex was for Pyrolusite (MnO2), Barium or both. The site is being described for the first time in the literature and offers an opportunity to fulfill the gap in literature regarding mining history. The discovery and the description of the site would also have implications in a wide multidisciplinary scientific community, including metallurgy, archeology, and world heritage.

>From the benefits of micro to the threats of nano for the ore-mining and ore-refining sectors

NASA Astrophysics Data System (ADS)

van Loon, A. J.

2002-07-01

Nanotechnology is developing fast, with much impact on a wide variety of industries. It is likely that current and future developments will result in the possibility to economically manipulate materials on a nanoscale. This will bring advantages on the one hand, as a further step forward after the development of technologies on a microscale, but it may also result in developments that make several now economically important activities largely, if not entirely, superfluous. The present-day progress in the field of recycling waste, in combination with developments that may make energy available in sufficient quantities at an acceptable price level, might result in technologies that isolate valuable compounds from waste at a nanoscale, thus, taking over the role of the mining industry as a provider of raw materials. It is suggested that the mining industry becomes strongly involved in nanoscale research, in order to combine their knowledge of ore properties and extraction methods with the knowledge of nanotechnological engineers about how to manipulate individual compounds. This may provide a chance for the present-day ore-mining and ore-refining companies to survive in a world that would otherwise probably not manage to supply sufficient raw materials for the Earth's growing population, which also will strive for a rise in the average standard of living.

Se Isotopes as groundwater redox indicators: Detecting natural attenuation of Se at an in situ recovery U mine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anirban, Basu; Schilling, Kathrin; Brown, Shaun T.

One of the major ecological concerns associated with the in situ recovery (ISR) of uranium (U) is the environmental release of soluble, toxic selenium (Se) oxyanions generated by mining. Post-mining natural attenuation by the residual reductants in the ore body and reduced down-gradient sediments should mitigate the risk of Se contamination in groundwater. Here in this work, we investigate the Se concentrations and Se isotope systematics of groundwater and of U ore bearing sediments from an ISR site at Rosita, TX, USA. Our results show that selenate (Se(VI)) is the dominant Se species in Rosita groundwater, and while several up-gradientmore » wells have elevated Se(VI), the majority of the ore zone and down-gradient wells have little or no Se oxyanions. In addition, the δ 82SeVI of Rosita groundwater is generally elevated relative to the U ore up to +6.14‰, with the most enriched values observed in the ore-zone wells. Increasing δ 82Se with decreasing Se(VI) conforms to a Rayleigh type distillation model with an ε of $-$2.25‰ ± 0.61‰, suggesting natural Se(VI) reduction occurring along the hydraulic gradient at the Rosita ISR site. Moreover, our results show that Se isotopes are excellent sensors for detecting and monitoring post-mining natural attenuation of Se oxyanions at ISR sites.« less

Se Isotopes as groundwater redox indicators: Detecting natural attenuation of Se at an in situ recovery U mine

DOE PAGES

Anirban, Basu; Schilling, Kathrin; Brown, Shaun T.; ...

2016-08-22

One of the major ecological concerns associated with the in situ recovery (ISR) of uranium (U) is the environmental release of soluble, toxic selenium (Se) oxyanions generated by mining. Post-mining natural attenuation by the residual reductants in the ore body and reduced down-gradient sediments should mitigate the risk of Se contamination in groundwater. Here in this work, we investigate the Se concentrations and Se isotope systematics of groundwater and of U ore bearing sediments from an ISR site at Rosita, TX, USA. Our results show that selenate (Se(VI)) is the dominant Se species in Rosita groundwater, and while several up-gradientmore » wells have elevated Se(VI), the majority of the ore zone and down-gradient wells have little or no Se oxyanions. In addition, the δ 82SeVI of Rosita groundwater is generally elevated relative to the U ore up to +6.14‰, with the most enriched values observed in the ore-zone wells. Increasing δ 82Se with decreasing Se(VI) conforms to a Rayleigh type distillation model with an ε of $-$2.25‰ ± 0.61‰, suggesting natural Se(VI) reduction occurring along the hydraulic gradient at the Rosita ISR site. Moreover, our results show that Se isotopes are excellent sensors for detecting and monitoring post-mining natural attenuation of Se oxyanions at ISR sites.« less

Abandoned mines and their impact on the environment: Case studies from Franklin and Sterling Mines, NJ and Rondout Quarry, NY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolkas, M.M.; Nehru, C.E.

1995-09-01

Water logged abandoned mines have an impact on the environment. In this project we selected abandoned mines from two sets of different ore bodies to learn about their environmental impact. Franklin and Sterling Pb-Zn mines, NJ and the limestone quarry in Rondout formation, NY were selected as case study examples. In the Pb-Zn mines metalimestone is the country rock and in the Rondout quarry limestone is the country rock. Soil water samples from selected strategic locations were analyzed for toxic and related heavy metal elements such as Pb, Zn, Cd, Cr and U. The levels of concentrations of these elementsmore » varied from one location to another according to the chemistry of the ore body and the ground movement throughout the area. In particular Cd, Cr and U concentration were variable from Franklin to Sterling mine. However, in the Rondout limestone (cement) quarry, higher concentrations of Cr and lower concentrations of Pb and Zn were noted. We conclude that ore body chemistry, mine dumps and tailing contaminated ponds along with the ground water movement throughout the area have an impact on the ground water and nearby river/stream contaminant chemistry in the areas.« less

Field Testing of Downgradient Uranium Mobility at an In-Situ Recovery Uranium Mine

NASA Astrophysics Data System (ADS)

Reimus, P. W.; Clay, J. T.; Rearick, M.; Perkins, G.; Brown, S. T.; Basu, A.; Chamberlain, K.

2015-12-01

In-situ recovery (ISR) mining of uranium involves the injection of O2 and CO2 (or NaHCO3) into saturated roll-front deposits to oxidize and solubilize the uranium, which is then removed by ion exchange at the surface and processed into U3O8. While ISR is economical and environmentally-friendly relative to conventional mining, one of the challenges of extracting uranium by this process is that it leaves behind a geochemically-altered aquifer that is exceedingly difficult to restore to pre-mining geochemical conditions, a regulatory objective. In this research, we evaluated the ability of the aquifer downgradient of an ISR mining area to attenuate the transport of uranium and other problem constituents that are mobilized by the mining process. Such an evaluation can help inform both regulators and the mining industry as to how much restoration of the mined ore zone is necessary to achieve regulatory compliance at various distances downgradient of the mining zone even if complete restoration of the ore zone proves to be difficult or impossible. Three single-well push-pull tests and one cross-well test were conducted in which water from an unrestored, previously-mined ore zone was injected into an unmined ore zone that served as a geochemical proxy for the downgradient aquifer. In all tests, non-reactive tracers were injected with the previously-mined ore zone water to allow the transport of uranium and other constituents to be compared to that of the nonreactive species. In the single-well tests, it was shown that the recovery of uranium relative to the nonreactive tracers ranged from 12-25%, suggesting significant attenuation capacity of the aquifer. In the cross-well test, selenate, molybdate and metavanadate were injected with the unrestored water to provide information on the transport of these potentially-problematic anionic constituents. In addition to the species-specific transport information, this test provided valuable constraints on redox conditions within the system, as redox couples involving these species collectively bracket the predicted transition redox potential for the U(VI)/U(IV) couple. Reduction should provide much longer-lasting immobilization of constituents than adsorption, especially given the inherent reducing characteristics of roll-front systems.

An investigation into heterogeneity in a single vein-type uranium ore deposit: Implications for nuclear forensics.

PubMed

Keatley, A C; Scott, T B; Davis, S; Jones, C P; Turner, P

2015-12-01

Minor element composition and rare earth element (REE) concentrations in nuclear materials are important as they are used within the field of nuclear forensics as an indicator of sample origin. However recent studies into uranium ores and uranium ore concentrates (UOCs) have shown significant elemental and isotopic heterogeneity from a single mine site such that some sites have shown higher variation within the mine site than that seen between multiple sites. The elemental composition of both uranium and gangue minerals within ore samples taken along a single mineral vein in South West England have been measured and reported here. The analysis of the samples was undertaken to determine the extent of the localised variation in key elements. Energy Dispersive X-ray spectroscopy (EDS) was used to analyse the gangue mineralogy and measure major element composition. Minor element composition and rare earth element (REE) concentrations were measured by Electron Probe Microanalysis (EPMA). The results confirm that a number of key elements, REE concentrations and patterns used for origin location do show significant variation within mine. Furthermore significant variation is also visible on a meter scale. In addition three separate uranium phases were identified within the vein which indicates multiple uranium mineralisation events. In light of these localised elemental variations it is recommended that representative sampling for an area is undertaken prior to establishing the REE pattern that may be used to identify the originating mine for an unknown ore sample and prior to investigating impact of ore processing on any arising REE patterns. Copyright © 2015 Elsevier Ltd. All rights reserved.

Influence of ore processing activity on Hg, As and Sb contamination and fractionation in soils in a former mining site of Monte Amiata ore district (Italy).

PubMed

Protano, Giuseppe; Nannoni, Francesco

2018-05-01

A geochemical study was carried out at the former Abbadia San Salvatore (ASS) mining site of the Monte Amiata ore district (Italy). Hg, As and Sb total contents and fractionation using a sequential extraction procedure were determined in soil and mining waste samples. Ore processing activities provided a different contribution to Hg contamination and concentration in soil fractions, influencing its behaviour as volatility and availability. Soils of roasting zone showed the highest Hg contamination levels mainly due to the deposition of Hg released as Hg 0 by furnaces during cinnabar roasting. High Hg contents were also measured in waste from the lower part of mining dump due to the presence of cinnabar. The fractionation pattern suggested that Hg was largely as volatile species in both uncontaminated and contaminated soils and mining waste, and concentrations of these Hg species increased as contamination increased. These findings were in agreement with the fact that the ASS mining site is characterized by high Hg concentrations in the air and the presence of Hg 0 liquid droplets in soil. Volatile Hg species were also prevalent in uncontaminated soils likely because the Monte Amiata region is an area characterized by anomalous fluxes of gaseous Hg from natural and anthropogenic inputs. At the ASS mining site soils were also contaminated by Sb, while As contents were comparable with its local background in soil. In all soil and waste samples Sb and As were preferentially in residual fraction. Copyright © 2018 Elsevier Ltd. All rights reserved.

40 CFR 440.103 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... that use dump, heap, in situ leach or vat-leach processes to extract copper from ores or ore waste... achievable (BAT). Except as provided in subpart L of this part and 40 CFR 125.30 through 125.32, any existing... achievable (BAT): (a) The concentration of pollutants discharged in mine drainage from mines that produce...

40 CFR 440.103 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... that use dump, heap, in situ leach or vat-leach processes to extract copper from ores or ore waste... economically achievable (BAT). Except as provided in subpart L of this part and 40 CFR 125.30 through 125.32... economically achievable (BAT): (a) The concentration of pollutants discharged in mine drainage from mines that...

40 CFR 440.103 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... that use dump, heap, in situ leach or vat-leach processes to extract copper from ores or ore waste... economically achievable (BAT). Except as provided in subpart L of this part and 40 CFR 125.30 through 125.32... economically achievable (BAT): (a) The concentration of pollutants discharged in mine drainage from mines that...

40 CFR 440.103 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... that use dump, heap, in situ leach or vat-leach processes to extract copper from ores or ore waste... achievable (BAT). Except as provided in subpart L of this part and 40 CFR 125.30 through 125.32, any existing... achievable (BAT): (a) The concentration of pollutants discharged in mine drainage from mines that produce...

Applied Geochemistry Special Issue on Environmental geochemistry of modern mining

USGS Publications Warehouse

Seal, Robert R.; Nordstrom, D. Kirk

2015-01-01

Environmental geochemistry is an integral part of the mine-life cycle, particularly for modern mining. The critical importance of environmental geochemistry begins with pre-mining baseline characterization and the assessment of environmental risks related to mining, continues through active mining especially in water and waste management practices, and culminates in mine closure. The enhanced significance of environmental geochemistry to modern mining has arisen from an increased knowledge of the impacts that historical and active mining can have on the environment, and from new regulations meant to guard against these impacts. New regulations are commonly motivated by advances in the scientific understanding of the environmental impacts of past mining. The impacts can be physical, chemical, and biological in nature. The physical challenges typically fall within the purview of engineers, whereas the chemical and biological challenges typically require a multidisciplinary array of expertise including geologists, geochemists, hydrologists, microbiologists, and biologists. The modern mine-permitting process throughout most of the world now requires that potential risks be assessed prior to the start of mining. The strategies for this risk assessment include a thorough characterization of pre-mining baseline conditions and the identification of risks specifically related to the manner in which the ore will be mined and processed, how water and waste products will be managed, and what the final configuration of the post-mining landscape will be.In the Fall 2010, the Society of Economic Geologists held a short course in conjunction with the annual meeting of the Geological Society of America in Denver, Colorado (USA) to examine the environmental geochemistry of modern mining. The intent was to focus on issues that are pertinent to current and future mines, as opposed to abandoned mines, which have been the focus of numerous previous short courses. The geochemical challenges of current and future mines share similarities with abandoned mines, but differences also exist. Mining and ore processing techniques have changed; the environmental footprint of waste materials has changed; environmental protection has become a more integral part of the mine planning process; and most historical mining was done with limited regard for the environment. The 17 papers in this special issue evolved from the Society of Economic Geologists’ short course.The relevant geochemical processes encompass the source, transport, and fate of contaminants related to the life cycle of a mine. Contaminants include metals and other inorganic species derived from geologic sources such as ore and solid mine waste, and substances brought to the site for ore processing, such as cyanide to leach gold. Factors, such as mine-waste mineralogy, hydrologic setting, mine-drainage chemistry, and microbial activity, that affect the hydrochemical risks from mining are reviewed by Nordstrom et al. In another paper, Nordstrom discusses baseline characterization at mine sites in a regulatory framework, and emphasizes the influence of mineral deposits in producing naturally elevated concentrations of many trace elements in surface water and groundwater. Surface water quality in mineralized watersheds is influenced by a number of processes that act on daily (diel) cycles and can produce dramatic variations in trace element concentrations as described by Gammons et al. Pre-mining baseline characterization studies should strive to capture the magnitude of these diel variations. Desbarats et al., using a case study of mine drainage from a gold mine, illustrate how elements that commonly occur as negatively charged species (anions) in solution, such as arsenic as arsenate, behave in an opposite fashion than most metals, which occur as positively charged species (cations). Significant improvement in the understanding of factors that influence the toxicity of metals to aquatic organisms in surface water has highlighted the importance of aqueous chemistry, particularly dissolved organic carbon, as described by Smith et al. Stream sediment contamination is another important pathway for affecting aquatic organisms, as reviewed by Besser et al. Understanding and predicting environmental consequences from mining begins with knowing the mineralogy and mineral reactivity of the ore, the wastes, and of secondary minerals formed later. Jamieson et al. review the importance of mineralogical studies in mine planning and remediation. A number of types of site-specific studies are needed to identify environmental risks related to individual mines. Lapakko reviews the general framework of mine waste characterization studies that are integral to the mine planning process. Hageman et al. present a comparative study of several static tests commonly used to characterize mine waste.The mining and ore processing practices employed at a specific mine site will vary on the basis of the commodities being targeted, the geology of the deposit, the geometry of the deposit, and the mining and ore processing methods used. Thus, these factors, in addition to the waste management practices used, can result in a variety of end-member mine waste features, each of which has its own set of challenges. Open pit mines and underground mines require waste rock to be removed to access ore. Waste rock presents unique problems because the rock is commonly mineralized at sub-economic grades and has not been processed to remove potentially problematic minerals, such as pyrite. Amos et al. examine the salient aspects of the geochemistry of waste rock. Mill tailings – the waste material after ore minerals have been removed – are a volumetrically important solid waste at many mine sites. Their fine grain size and the options for their management make their behavior in the environment distinct from that of waste rock. Lindsay et al. describe some of these differences through three case-study examples. Subaqueous disposal of tailings is another option described by Moncur et al. Cyanide leaching for gold extraction is a common method throughout the world. Johnson describes environmental aspects of cyanidation. Uranium mining presents unique environmental challenges, particularly since in-situ recovery has seen widespread use. Campbell et al. review the environmental geochemistry of uranium mining and current research on bioremediation. Ore concentrates from many types of metal mining undergo a pyrometallurgical technique known as smelting to extract the metal. Slag is the result of smelting, and it may be an environmental liability or a valuable byproduct, as described by Piatak et al. Finally, the open pits that result from surface mining commonly reach below the water table. At the end of mining, these pits may fill to form lakes that become part of the legacy of the mine. Castendyk et al., in two papers, review theoretical aspects of the environmental limnology of pit lakes. They also describe approaches that have been used to model pit lake water balance, wall-rock contributions to pit lake chemistry, pit lake water quality, and limnological processes, such as vertical mixing, through the use of three case studies.

Controls on the Mobility of Antimony in Mine Waste from Three Deposit Types

NASA Astrophysics Data System (ADS)

Jamieson, H.; Radková, A. B.; Fawcett, S.

2017-12-01

Antimony can be considered both a critical metal and an environmental hazard, with a toxicity similar to arsenic. It is concentrated in stibnite deposits, but also present in polymetallic and precious metal ores, frequently accompanied by arsenic. We have studied the mineralogical controls on the mobility of antimony in three types of mine waste: stibnite tailings from an antimony mine, tetrahedrite-bearing waste rock from copper mining, and gold mine tailings and ore roaster waste. Our results demonstrate that the tendency of antimony to leach into the aqueous environment or remain sequestered in solid phases depends on the primary host minerals and conditions governing the precipitation of secondary antimony-hosting phases. In tailings at the Beaver Brook antimony mine in Newfoundland, Canada, stibnite oxidizes rapidly, and secondary minerals such as the relatively insoluble Sb-Fe tripuhyite-like phase and Sb-bearing goethite. However, under dry conditions, the most important secondary Sb host is the Mg-Sb hydroxide brandholzite, but this easily soluble mineral disappears when it rains. Antimony that was originally hosted in tetrahedrite, a complex multi-element sulfosalt, in the historic waste rock piles at Špania Dolina-Piesky, Slovakia, is not as mobile as Cu and As during weathering but reprecipiates to a mixture of tripuhyite and romeite. Finally, the original antimony-hosting minerals, both stibnite and sulphosalts, in the gold ore at Giant Mine, Yellowknife, Canada were completely destroyed during ore roasting. In tailings-contaminated sediments, antimony persists in roaster-generated iron oxide phases, except under reducing conditions where some of the antimony forms a Sb-S phase. The combined presence of antimony and arsenic in mine waste complicates risk assessment but in general, our findings suggest that antimony is less mobile than arsenic in the environment.

3D implicit modeling of the Sishen Mine: new resolution of the geometry and origin of Fe mineralization

NASA Astrophysics Data System (ADS)

Stoch, B.; Anthonissen, C. J.; McCall, M.-J.; Basson, I. J.; Deacon, J.; Cloete, E.; Botha, J.; Britz, J.; Strydom, M.; Nel, D.; Bester, M.

2017-12-01

The Sishen deposit is one of the largest iron ore concentrations in current production. Hematite mineralization occurs along a strike length of 14 km, with a width of 3.2 km and a maximum vertical extent of 400 m below the original surface. The 986-Mt reserve incorporates a suite of individual orebodies, beneath a locally preserved tectonized unconformity, with a wide range of geometries, depths, and orientations. Fully constrained, implicit 3D modeling of the entire mining volume (> 70 km3), was undertaken to the original, pre-mining topography. The model incorporates 5287 mapping points and > 21,000 drillholes and provides exceptional insight into the original configuration of ore and its relationship to contacts, unconformities, and structures in the enclosing country rock. The bulk of ore occurs to the west of a strike-extensive, partially inverted normal fault (Sloep Fault), within an asymmetrical synclinal structure on its western flank. This linear, N-S distribution of deep, thick ore is punctuated by palaeosinkholes, wherein base-of-ore dips of greater than 45°, are concentrically arranged. Localized ore volumes also occur along faults and in fault-bounded, downthrown blocks, to the north of NW-SE- and NE-SW-trending strike-slip faults that show relatively minor uplift to the south, probably due to the Lomanian Namaqua-Natal Orogeny. The revised model demonstrates the proximity of ore to a tectonized unconformity and highlights the structural control on ore volumes, implying that Fe mineralization at Sishen cannot be exclusively attributed to supergene enrichment and concentric palaeosinkhole formation.

Seismic safety in conducting large-scale blasts

NASA Astrophysics Data System (ADS)

Mashukov, I. V.; Chaplygin, V. V.; Domanov, V. P.; Semin, A. A.; Klimkin, M. A.

2017-09-01

In mining enterprises to prepare hard rocks for excavation a drilling and blasting method is used. With the approach of mining operations to settlements the negative effect of large-scale blasts increases. To assess the level of seismic impact of large-scale blasts the scientific staff of Siberian State Industrial University carried out expertise for coal mines and iron ore enterprises. Determination of the magnitude of surface seismic vibrations caused by mass explosions was performed using seismic receivers, an analog-digital converter with recording on a laptop. The registration results of surface seismic vibrations during production of more than 280 large-scale blasts at 17 mining enterprises in 22 settlements are presented. The maximum velocity values of the Earth’s surface vibrations are determined. The safety evaluation of seismic effect was carried out according to the permissible value of vibration velocity. For cases with exceedance of permissible values recommendations were developed to reduce the level of seismic impact.

[Dust and gas factors in extraction of polymetallic ore in Arctic conditions and their hygienic assessment].

PubMed

Borisenkova, R V; Lutsenko, L A; Skriabin, S Iu; Khristenko, P P

1996-01-01

Studies of drilling and blasting method of copper and nickel ores extraction at underground Transpolar mines proved that the highest concentrations of dust appeared during dry drilling of vertical blast holes, work of scraper windlass, fragmentation of out-size blocks, preparation of concrete mixture. Presence of aggressive metals, especially nickel, in the ore dust is a main base for planned thorough investigations of fibrogenic, toxic and carcinogenic effects of copper and nickel ore dust, for more precise assessment of its MAC in the air of workplace. Two-step purification of exhaust gases appearing due to mining diesel machines is not quite efficient, as the concentrations of nitrogen oxides (assessed through nitrogen dioxide) continually exceeded the MAC.

25. DETAIL OF STRUCTURAL TIMBERS, ORE BIN, AND STAIRWAY TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. DETAIL OF STRUCTURAL TIMBERS, ORE BIN, AND STAIRWAY TO TOP FLOOR OF MILL, LOOKING SOUTH FROM SECOND FLOOR OF MILL. PORTION OF ORE BIN ON RIGHT, STAIRS ON LEFT. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

The Structure of Reclaiming Warehouse of Minerals at Open-Cut Mines with the Use Combined Transport

NASA Astrophysics Data System (ADS)

Ikonnikov, D. A.; Kovshov, S. V.

2017-07-01

In the article performed an analysis of ore reclaiming and overloading point characteristics at modern opencast mines. Ore reclaiming represents the most effective way of stability support of power-intensive and expensive technological dressing process, and, consequently, of maintenance of the optimal production and set-up parameters of extraction and quality of finished product. The paper proposed the construction of the warehouse describing the technology of its creation. Equipment used for the warehouse described in detail. All stages of development and operation was shown. Advantages and disadvantages of using mechanical shovel excavator and hydraulic excavator “backdigger” as a reloading and reclaiming equipment was compared. Ore reclaiming and overloading point construction at cyclical and continuous method of mining using a hydraulic excavator “backdigger” was proposed.

Biomining: metal recovery from ores with microorganisms.

PubMed

Schippers, Axel; Hedrich, Sabrina; Vasters, Jürgen; Drobe, Malte; Sand, Wolfgang; Willscher, Sabine

2014-01-01

Biomining is an increasingly applied biotechnological procedure for processing of ores in the mining industry (biohydrometallurgy). Nowadays the production of copper from low-grade ores is the most important industrial application and a significant part of world copper production already originates from heap or dump/stockpile bioleaching. Conceptual differences exist between the industrial processes of bioleaching and biooxidation. Bioleaching is a conversion of an insoluble valuable metal into a soluble form by means of microorganisms. In biooxidation, on the other hand, gold is predominantly unlocked from refractory ores in large-scale stirred-tank biooxidation arrangements for further processing steps. In addition to copper and gold production, biomining is also used to produce cobalt, nickel, zinc, and uranium. Up to now, biomining has merely been used as a procedure in the processing of sulfide ores and uranium ore, but laboratory and pilot procedures already exist for the processing of silicate and oxide ores (e.g., laterites), for leaching of processing residues or mine waste dumps (mine tailings), as well as for the extraction of metals from industrial residues and waste (recycling). This chapter estimates the world production of copper, gold, and other metals by means of biomining and chemical leaching (bio-/hydrometallurgy) compared with metal production by pyrometallurgical procedures, and describes new developments in biomining. In addition, an overview is given about metal sulfide oxidizing microorganisms, fundamentals of biomining including bioleaching mechanisms and interface processes, as well as anaerobic bioleaching and bioleaching with heterotrophic microorganisms.

Iron ore mines leachate potential for oxyradical production.

PubMed

Hamoutene, D; Rahimtula, A; Payne, J

2000-06-01

The ecotoxicological effects of mining effluents is coming under much greater scrutiny. It appears necessary to explore possible health effects in association with iron ore mining effluents. The present results clearly demonstrate that iron-ore leachate is not an inert media but has the potential to induce lipid peroxidation. Peroxidation was assessed by measuring oxygen consumption in the presence of a reducing agent such as ascorbate or NADPH and a chelator such as EDTA. Labrador iron ore is an insoluble complex crystalline material containing a mixture of metals (Fe, Al, Ti, Mn, Mg,ellipsis, ) in contrast to the iron sources used for normal lipid peroxidation studies. The metal of highest percentage is iron (59. 58%), a metal known to induce oxyradical production. Iron ore powder initiated ascorbic acid-dependent lipid peroxidation (nonenzymatic) in liposomes, lipids extracted from rat and salmon liver microsomes, and intact salmon liver microsomes. It also revealed an inhibitory effect of NADPH-dependent microsomes lipid peroxidation as well as on NADPH cytochrome c reductase activity. However, nonenzymatic peroxidation in rat liver microsomes was not significantly inhibited. Cytochrome P450 IA1- and IIB1-dependent enzymatic activities as well as P450 levels were not affected. The inhibition could be due to one of the other components of iron ore leachate (Mn, Al,ellipsis, ). These effects of iron-ore leachate indicate that a potential toxicity could be associated with its release into lakes. Further studies are necessary to explore in vivo effects on aquatic animals. Copyright 2000 Academic Press.

UV-Fluorescent Sensing for Primary Selection of Metal-rich Seafloor Massive Sulfide Ore

NASA Astrophysics Data System (ADS)

Yamazaki, T.; Nakatani, T.; Nakatani, N.; Arai, R.

2012-12-01

Seafloor massive sulfides (SMS) in the western Pacific have received much attention as resources for Au, Ag, Cu, Zn, and Pb. Because of the higher metal contents, the venture commercial mining project may start in 2013 in the East Manus Basin, Papua New Guinea. One of important problems to be solved is reducing the waste rock disposal costs for the economy. The best location for the reducing is on seafloor just after the excavation of SMS ores. The authors select UV-fluorescent sensing for primary selection of the ores, because no additional environmental impact is created with the application of the method. First of all, the effectiveness of the UV-fluorescent sensing by a combination system with a UV-light and a camera (See attached figure) in deep water condition is clarified. Then many UV-fluorescent data of SMS ore, SMS accompanied rock, and seafloor rock samples are collected. In the analyses phase, the ore and rock samples are classified into some groups by applying the cluster analysis to the metal contents at first. Then, using the UV fluorescent color brightness and contrasts of the ore and rock samples, the discriminant analysis based on Mahalanobis distance is applied. The higher possibility to identify the SMS ores containing valuable metals from camera image is suggested from the analyses. When additional UV-fluorescent and chemical assay data are obtained, the renewal of discriminant analysis is necessary. Therefore, the results and conclusions described in this study are tentative ones.; UV-fluorescent sensing

THE EPA/DOE MINE WASTE TECHNOLOGY PROGRAM

EPA Science Inventory

Mining activities in the US (not counting coal) produce between 1-2B tons of mine waste annually. Since many of the ore mines involve sulfide minerals, the production of acid mine drainage (AMD) is a common problem from these abandoned mine sites. The combination of acidity, heav...

15. NORTH ELEVATION OF UPPER ORE BIN, CHUTE, AND JAW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. NORTH ELEVATION OF UPPER ORE BIN, CHUTE, AND JAW CRUSHER, LOOKING SOUTH FROM END OF CONVEYOR PLATFORM. NOTICE THE THREE ORE BIN CONTROL DOORS, CORRESPONDING TO SEPARATE COMPARTMENTS OF THE BIN. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

U.S. ARMY CORPS OF ENGINEERS ABANDONED MINE LAND REMEDIATION WORKSHOP

EPA Science Inventory

Mining activities in the US (not counting coal) produce 1-2 billion tons of mine waste annually. Since many of the ore mines involve sulfide minerals, the production of acid mine drainage (AMD) is a common problem from these abandoned mine sites. The combination of acidity, heavy...

ASSESSING AND MANAGING MERCURY FROM HISTORIC AND CURRENT MINING ACTIVITIES

EPA Science Inventory

Mining activities in the US (not counting coal) produce between one and two billion tons of mine waste annually. Since many of the ore mines involve sulfide minerals, the production of acid mine drainage (AMD) is a common problem from these abandoned mine sites. The combination o...

Radioactive rare-earth deposit at Scrub Oaks mine, Morris County, New Jersey

USGS Publications Warehouse

Klemic, Harry; Heyl, A.V.; Taylor, Audrey R.; Stone, Jerome

1959-01-01

A deposit of rare-earth minerals in the Scrub Oaks iron mine, Morris County, N. J., was mapped and sampled in 1955. The rare-earth minerals are mainly in coarse-grained magnetite ore and in pegmatite adjacent to it. Discrete bodies of rare-earth-bearing magnetite ore apparently follow the plunge of the main magnetite ore body at the north end of the mine. Radioactivity of the ore containing rare earths is about 0.2 to 0.6 mllliroentgens per hour. The principal minerals of the deposit are quartz, magnetite, hematite, albiteoligoclase, perthite and antiperthite. Xenotime and doverite aggregates and bastnaesite with intermixed leucoxene are the most abundant rare-earth minerals, and zircon, sphene, chevkinite, apatite, and monazite are of minor abundance in the ore. The rare-earth elements are partly differentiated into cerium-rich bastnaesite, chevkinite, and monazite, and yttrium-rich xenotime and doverite. Apatite, zircon, and sphene contain both cerium and yttrium group earths. Eleven samples of radioactive ore and rock average 0.009 percent uranium, 0.062 percent thorium, 1.51 percent combined rare-earth oxides including yttrium oxide and 24.8 percent iron. Scatter diagrams of sample data show a direct correlation between equivalent uranium, uranium, thorium, and combined rare^ earth oxides. Both cerium- and yttrium-group earths are abundant in the rare-earth minerals. Radioactive magnetite ore containing rare-earth minerals probably formed as a variant of the magnetite mineralization that produced the main iron ore of the Scrub Oaks deposit. The rare-earth minerals and the iron ore were deposited contemporaneously. Zircon crystals, probably deposited at the same time, have been determined by the Larsen method to be about 550 to 600 million years old (late Precambrian age). Uranium, thorium, and rare-earth elements are potential byproducts of iron in the coarse-grained magnetite ore.

A case–control study of mesothelioma in Minnesota iron ore (taconite) miners

PubMed Central

Lambert, Christine S; Alexander, Bruce H; Ramachandran, Gurumurthy; MacLehose, Richard F; Nelson, Heather H; Ryan, Andrew D; Mandel, Jeffrey H

2018-01-01

Objectives An excess of mesothelioma has been observed in iron ore miners in Northeastern Minnesota. Mining and processing of taconite iron ore generate exposures that include elongate mineral particles (EMPs) of amphibole and non-amphibole origin. We conducted a nested case–control study of mesothelioma in a cohort of 68 737 iron ore miners (haematite and taconite ore miners) to evaluate the association between mesothelioma, employment and EMP exposures from taconite mining. Methods Mesothelioma cases (N=80) were identified through the Minnesota Cancer Surveillance System (MCSS) and death certificates. Four controls of similar age were selected for each case with 315 controls ultimately eligible for inclusion. Mesothelioma risk was evaluated by estimating rate ratios and 95% CIs with conditional logistic regression in relation to duration of taconite industry employment and cumulative EMP exposure [(EMP/cc)×years], defined by the National Institute for Occupational Safety and Health (NIOSH) 7400 method. Models were adjusted for employment in haematite mining and potential exposure to commercial asbestos products used in the industry. Results All mesothelioma cases were male and 57 of the cases had work experience in the taconite industry. Mesothelioma was associated with the number of years employed in the taconite industry (RR=1.03, 95% CI 1.00 to 1.06) and cumulative EMP exposure (RR=1.10, 95% CI 0.97 to –1.24). No association was observed with employment in haematite mining. Conclusions These results support an association between mesothelioma and employment duration and possibly EMP exposure in taconite mining and processing. The type of EMP was not determined. The potential role of commercial asbestos cannot be entirely ruled out. PMID:26655961

A case-control study of mesothelioma in Minnesota iron ore (taconite) miners.

PubMed

Lambert, Christine S; Alexander, Bruce H; Ramachandran, Gurumurthy; MacLehose, Richard F; Nelson, Heather H; Ryan, Andrew D; Mandel, Jeffrey H

2016-02-01

An excess of mesothelioma has been observed in iron ore miners in Northeastern Minnesota. Mining and processing of taconite iron ore generate exposures that include elongate mineral particles (EMPs) of amphibole and non-amphibole origin. We conducted a nested case-control study of mesothelioma in a cohort of 68,737 iron ore miners (haematite and taconite ore miners) to evaluate the association between mesothelioma, employment and EMP exposures from taconite mining. Mesothelioma cases (N=80) were identified through the Minnesota Cancer Surveillance System (MCSS) and death certificates. Four controls of similar age were selected for each case with 315 controls ultimately eligible for inclusion. Mesothelioma risk was evaluated by estimating rate ratios and 95% CIs with conditional logistic regression in relation to duration of taconite industry employment and cumulative EMP exposure [(EMP/cc)×years], defined by the National Institute for Occupational Safety and Health (NIOSH) 7400 method. Models were adjusted for employment in haematite mining and potential exposure to commercial asbestos products used in the industry. All mesothelioma cases were male and 57 of the cases had work experience in the taconite industry. Mesothelioma was associated with the number of years employed in the taconite industry (RR=1.03, 95% CI 1.00 to 1.06) and cumulative EMP exposure (RR=1.10, 95% CI 0.97 to -1.24). No association was observed with employment in haematite mining. These results support an association between mesothelioma and employment duration and possibly EMP exposure in taconite mining and processing. The type of EMP was not determined. The potential role of commercial asbestos cannot be entirely ruled out. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Abandoned Mine Lands

EPA Pesticide Factsheets

Abandoned Mine Lands are those lands, waters, and surrounding watersheds where extraction, beneficiation, or processing of ores and minerals (excluding coal) has occurred. These lands also include areas where mining or processing activity is inactive.

Evaluation of Rock Bolt Support for Polish Hard Rock Mines

NASA Astrophysics Data System (ADS)

Skrzypkowski, Krzysztof

2018-03-01

The article presents different types of rock bolt support used in Polish ore mining. Individual point resin and expansion rock bolt support were characterized. The roof classes for zinc and lead and copper ore mines were presented. Furthermore, in the article laboratory tests of point resin rock bolt support in a geometric scale of 1:1 with minimal fixing length of 0.6 m were made. Static testing of point resin rock bolt support were carried out on a laboratory test facility of Department of Underground Mining which simulate mine conditions for Polish ore and hard coal mining. Laboratory tests of point resin bolts were carried out, especially for the ZGH Bolesław, zinc and lead "Olkusz - Pomorzany" mine. The primary aim of the research was to check whether at the anchoring point length of 0.6 m by means of one and a half resin cartridge, the type bolt "Olkusz - 20A" is able to overcome the load.The second purpose of the study was to obtain load - displacement characteristic with determination of the elastic and plastic range of the bolt. For the best simulation of mine conditions the station steel cylinders with an external diameter of 0.1 m and a length of 0.6 m with a core of rock from the roof of the underground excavations were used.

Isotopic evidence for reductive immobilization of uranium across a roll-front mineral deposit

DOE PAGES

Brown, Shaun T.; Basu, Anirban; Christensen, John N.; ...

2016-05-20

We use uranium (U) isotope ratios to detect and quantify the extent of natural U reduction in groundwater across a roll front redox gradient. Our study was conducted at the Smith Ranch-Highland in situ recovery (ISR) U mine in eastern Wyoming, USA, where economic U deposits occur in the Paleocene Fort Union formation. To evaluate the fate of aqueous U in and adjacent to the ore body, we investigated the chemical composition and isotope ratios of groundwater samples from the roll-front type ore body and surrounding monitoring wells of a previously mined area. The 238U/ 235U of groundwater varies bymore » approximately 3‰ and is correlated with U concentrations. Fluid samples down-gradient of the ore zone are the most depleted in 238U and have the lowest U concentrations. Activity ratios of 234U/ 238U are ~5.5 up-gradient of the ore zone, ~1.0 in the ore zone, and between 2.3 and 3.7 in the down-gradient monitoring wells. High-precision measurements of 234U/ 238U and 238U/ 235U allow for development of a conceptual model that evaluates both the migration of U from the ore body and the extent of natural attenuation due to reduction. We find that the premining migration of U down-gradient of the delineated ore body is minimal along eight transects due to reduction in or adjacent to the ore body, whereas two other transects show little or no sign of reduction in the down-gradient region. Lastly, these results suggest that characterization of U isotopic ratios at the mine planning stage, in conjunction with routine geochemical analyses, can be used to identify where more or less postmining remediation will be necessary.« less

Mercury isotope fractionation during ore retorting in the Almadén mining district, Spain

USGS Publications Warehouse

Gray, John E.; Pribil, Michael J.; Higueras, Pablo L.

2013-01-01

Almadén, Spain, is the world's largest mercury (Hg) mining district, which has produced over 250,000 metric tons of Hg representing about 30% of the historical Hg produced worldwide. The objective of this study was to measure Hg isotopic compositions of cinnabar ore, mine waste calcine (retorted ore), elemental Hg (Hg0(L)), and elemental Hg gas (Hg0(g)), to evaluate potential Hg isotopic fractionation. Almadén cinnabar ore δ202Hg varied from − 0.92 to 0.15‰ (mean of − 0.56‰, σ = 0.35‰, n = 7), whereas calcine was isotopically heavier and δ202Hg ranged from − 0.03‰ to 1.01‰ (mean of 0.43‰, σ = 0.44‰, n = 8). The average δ202Hg enrichment of 0.99‰ between cinnabar ore and calcines generated during ore retorting indicated Hg isotopic mass dependent fractionation (MDF). Mass independent fractionation (MIF) was not observed in any of the samples in this study. Laboratory retorting experiments of cinnabar also were carried out to evaluate Hg isotopic fractionation of products generated during retorting such as calcine, Hg0(L), and Hg0(g). Calcine and Hg0(L) generated during these retorting experiments showed an enrichment in δ202Hg of as much as 1.90‰ and 0.67‰, respectively, compared to the original cinnabar ore. The δ202Hg for Hg0(g) generated during the retorting experiments was as much as 1.16‰ isotopically lighter compared to cinnabar, thus, when cinnabar ore was roasted, the resultant calcines formed were isotopically heavier, whereas the Hg0(g) generated was isotopically lighter in Hg isotopes.

Control of Rock Mechanics in Underground Ore Mining

NASA Astrophysics Data System (ADS)

Golik, V. I.; Efremenkov, A. B.

2017-07-01

Performance indicators in underground mining of thick iron fields can be insufficient since geo-mechanic specifics of ore-hosting fields might be considered inadequately, as a consequence, critical deformations and even earth’s surface destruction are possible, lowering the indicators of full subsurface use, this way. The reason for it is the available approach to estimating the performance of mining according to ore excavation costs, without assessing losses of valuable components and damage to the environment. The experimental approach to the problem is based on a combination of methods to justify technical capability and performance of mining technology improvement with regard to geomechanical factors. The main idea of decisions to be taken is turning geo-materials into the condition of triaxial compression via developing the support constructions of blocked up structural rock block. The study was carried out according to an integrated approach based on the analysis of concepts, field observations, and simulation with the photo-elastic materials in conditions of North Caucasus deposits. A database containing information on the deposit can be developed with the help of industrial experiments and performance indicators of the field can be also improved using the ability of ore-hosting fields to develop support constructions, keeping the geo-mechanical stability of the system at lower cost, avoiding ore contamination at the processing stage. The proposed model is a specific one because an adjustment coefficient of natural and anthropogenic stresses is used and can be adopted for local conditions. The relation of natural to anthropogenic factors can make more precise the standards of developed, prepared and ready to excavation ore reserves relying on computational methods. It is possible to minimize critical stresses and corresponding deformations due to dividing the ore field into sectors safe from the standpoint of geo-mechanics, and using less cost-demanding ways of keeping rock massif stable.

40 CFR 440.54 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... reduction attainable by the applications of the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines obtaining titanium ores from lode deposits...) The concentration of pollutants discharged in mine drainage from mines engaged in the dredge mining of...

40 CFR 440.54 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... reduction attainable by the applications of the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines obtaining titanium ores from lode deposits...) The concentration of pollutants discharged in mine drainage from mines engaged in the dredge mining of...

40 CFR 440.54 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... reduction attainable by the applications of the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines obtaining titanium ores from lode deposits...) The concentration of pollutants discharged in mine drainage from mines engaged in the dredge mining of...

Mössbauer analysis of BIOX treatment of ores at Wiluna gold mine, Western Australia

NASA Astrophysics Data System (ADS)

Gagliardi, F. M.; Cashion, J. D.

2013-04-01

Mössbauer phase analysis of samples taken from nine stages of the bacterial oxidation processing of gold ore at the Wiluna Gold Mine followed the transformation of the arsenopyrite/pyrite minerals. The principal end-stage phases were szomolnokite, ferric oxyhydroxides, ferric arsenates, jarosite and incompletely transformed pyrite, with higher hydrates of ferrous sulphate being created and then dehydrating to szomolnokite during the processing.

Feasibility Studies for Production of Pellet Grade Concentrate from Sub Grade Iron Ore Using Multi Gravity Separator

NASA Astrophysics Data System (ADS)

Rao, Gottumukkala Venkateswara; Markandeya, R.; Kumar, Rajan

2018-04-01

An attempt has been made to utilise Sub Grade Iron Ore by producing pellet grade concentrate from Deposit 5, Bacheli Complex, Bailadila, Chhattisgarh, India. The `as received' Run of Mine (ROM) sample assayed 40.80% Fe, 40.90% SiO2. Mineralogical studies indicated that the main ore mineral is Hematite and lone gangue mineral is Quartz. Mineral liberation studies indicated that, the ore mineral Hematite and gangue mineral Quartz are getting liberated below 100 microns. The stage crushed and ground sample was subjected to concentration by using a Multi Gravity Separator (MGS). Rougher Multi Gravity Separation (MGS) experimental results were optimised to recover highest possible iron values. A concentrate of 55.80% Fe with a yield of 61.73% by weight with a recovery of 84.42% Iron values was obtained in rougher MGS concentrate. Further experiments were carried out with rougher MGS concentrate to produce a concentrate suitable for commercial grade pellet concentrate. It was proved that a concentrate assaying 66.67% Fe, 3.12% SiO2 with an yield of 45.08% by weight and with a recovery of 73.67% iron values in the concentrate.

Resource potential for commodities in addition to Uranium in sandstone-hosted deposits: Chapter 13

USGS Publications Warehouse

Breit, George N.

2016-01-01

Sandstone-hosted deposits mined primarily for their uranium content also have been a source of vanadium and modest amounts of copper. Processing of these ores has also recovered small amounts of molybdenum, rhenium, rare earth elements, scandium, and selenium. These deposits share a generally common origin, but variations in the source of metals, composition of ore-forming solutions, and geologic history result in complex variability in deposit composition. This heterogeneity is evident regionally within the same host rock, as well as within districts. Future recovery of elements associated with uranium in these deposits will be strongly dependent on mining and ore-processing methods.

Improving the sensitivity and accuracy of gamma activation analysis for the rapid determination of gold in mineral ores.

PubMed

Tickner, James; Ganly, Brianna; Lovric, Bojan; O'Dwyer, Joel

2017-04-01

Mining companies rely on chemical analysis methods to determine concentrations of gold in mineral ore samples. As gold is often mined commercially at concentrations around 1 part-per-million, it is necessary for any analysis method to provide good sensitivity as well as high absolute accuracy. We describe work to improve both the sensitivity and accuracy of the gamma activation analysis (GAA) method for gold. We present analysis results for several suites of ore samples and discuss the design of a GAA facility designed to replace conventional chemical assay in industrial applications. Copyright © 2017. Published by Elsevier Ltd.

Experimenting With Ore: Creating the Taconite Process; flow chart of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Experimenting With Ore: Creating the Taconite Process; flow chart of process - Mines Experiment Station, University of Minnesota, Twin Cities Campus, 56 East River Road, Minneapolis, Hennepin County, MN

LAND REBORN: TOOLS FOR THE 21ST CENTURY/NATIONAL ASSOCIATION OF ABANDONED MINE LAND PROGRAMS

EPA Science Inventory

Mining activities in the US (not counting coal) produce 1-2 billion tons of mine waste annually. Since many of the ore mines involve sulfide minerals, the production of acid mine drainage (AMD) is a common problem from these abandoned mine sites. The combination of acidity, heavy...

Hydrogeochemical assessment of mine-impacted water and sediment of iron ore mining

NASA Astrophysics Data System (ADS)

Nur Atirah Affandi, Fatin; Kusin, Faradiella Mohd; Aqilah Sulong, Nur; Madzin, Zafira

2018-04-01

This study was carried out to evaluate the hydrogeochemical behaviour of mine-impacted water and sediment of a former iron ore mining area. Sampling of mine water and sediment were carried out at selected locations within the mine including the former mining ponds, mine tailings and the nearby stream. The water samples were analysed for their hydrochemical facies, major and trace elements including heavy metals. The water in the mining ponds and the mine tailings was characterised as highly acidic (pH 2.54-3.07), but has near-neutral pH in the nearby stream. Results indicated that Fe and Mn in water have exceeded the recommended guidelines values and was also supported by the results of geochemical modelling. The results also indicated that sediments in the mining area were contaminated with Cd and As as shown by the potential ecological risk index values. The total risk index of heavy metals in the sediment were ranked in the order of Cd>As>Pb>Cu>Zn>Cr. Overall, the extent of potential ecological risks of the mining area were categorised as having low to moderate ecological risk.

30 CFR 57.22003 - Mine category or subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Methane in Metal and Nonmetal Mines Mine Categorization § 57.22003 Mine category or... methane and dusts containing volatile matter. Categories and subcategories are defined as follows: (1) Category I applies to mines that operate within a combustible ore body and either liberate methane or have...

40 CFR 440.54 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... attainable by the applications of the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines obtaining titanium ores from lode deposits shall not exceed... pollutants discharged in mine drainage from mines engaged in the dredge mining of placer deposits of sands...

40 CFR 440.54 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... attainable by the applications of the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines obtaining titanium ores from lode deposits shall not exceed... pollutants discharged in mine drainage from mines engaged in the dredge mining of placer deposits of sands...

75 FR 3753 - Agency Information Collection Activities: Comment Request for the USGS Mine, Development, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-22

... to make domestic ore resource analyses. Tabulations of volumetric data concerning domestic mining... mined and the resulting marketable product. These data are an indicator of the future mining outlook... the U.S. Geological Survey with domestic production, exploration, and mine development data for...

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 4 2010-04-01 2010-04-01 false Depletion on extraction of ores or minerals from... Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or residue of prior... section 613(c)(3) (relating to extraction of ores or minerals from the ground). Thus, an acquiring...

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 4 2013-04-01 2013-04-01 false Depletion on extraction of ores or minerals from...) Insolvency Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or... the applicability of section 613(c)(3) (relating to extraction of ores or minerals from the ground...

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 4 2011-04-01 2011-04-01 false Depletion on extraction of ores or minerals from... Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or residue of prior... section 613(c)(3) (relating to extraction of ores or minerals from the ground). Thus, an acquiring...

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 4 2012-04-01 2012-04-01 false Depletion on extraction of ores or minerals from...) Insolvency Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or... the applicability of section 613(c)(3) (relating to extraction of ores or minerals from the ground...

26 CFR 1.381(c)(18)-1 - Depletion on extraction of ores or minerals from the waste or residue of prior mining.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 4 2014-04-01 2014-04-01 false Depletion on extraction of ores or minerals from...) Insolvency Reorganizations § 1.381(c)(18)-1 Depletion on extraction of ores or minerals from the waste or... the applicability of section 613(c)(3) (relating to extraction of ores or minerals from the ground...

25 CFR 214.13 - Diligence; annual expenditures; mining records.

Code of Federal Regulations, 2013 CFR

2013-04-01

... ores by drilling within 1 year test holes aggregating 2,000 feet unless a sufficient ore body is... of the drill holes, to justify the expenditure, the sinking of a shaft to the ore body, and the... leased premises accurate records of the drilling, redrilling, or deepening of all holes showing the...

25 CFR 214.13 - Diligence; annual expenditures; mining records.

Code of Federal Regulations, 2014 CFR

2014-04-01

... ores by drilling within 1 year test holes aggregating 2,000 feet unless a sufficient ore body is... of the drill holes, to justify the expenditure, the sinking of a shaft to the ore body, and the... leased premises accurate records of the drilling, redrilling, or deepening of all holes showing the...

75 FR 22469 - National Emission Standards for Hazardous Air Pollutants: Gold Mine Ore Processing and Production...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-28

... the lower TRI reporting threshold for mercury that went into effect about that time. Following this... roasting temperatures, which readily volatilize available mercury from the ore. The mercury concentrations... temperatures. Dry grinding of the ore prior to roasting is primarily a source of particulate matter (PM...

3&4D Geomodeling Applied to Mineral Resources Exploration - A New Tool for Targeting Deposits.

NASA Astrophysics Data System (ADS)

Royer, Jean-Jacques; Mejia, Pablo; Caumon, Guillaume; Collon-Drouaillet, Pauline

2013-04-01

3 & 4D geomodeling, a computer method for reconstituting the past deformation history of geological formations, has been used in oil and gas exploration for more than a decade for reconstituting fluid migration. It begins nowadays to be applied for exploring with new eyes old mature mining fields and new prospects. We describe shortly the 3&4D geomodeling basic notions, concepts, and methodology when applied to mineral resources assessment and modeling ore deposits, pointing out the advantages, recommendations and limitations, together with new challenges they rise. Several 3D GeoModels of mining explorations selected across Europe will be presented as illustrative case studies which have been achieved during the EU FP7 ProMine research project. It includes: (i) the Cu-Au porphyry deposits in the Hellenic Belt (Greece); (ii) the VMS in the Iberian Pyrite Belt including the Neves Corvo deposit (Portugal) and (iii) the sediment-hosted polymetallic Cu-Ag (Au, PGE) Kupferschiefer ore deposit in the Foresudetic Belt (Poland). In each case full 3D models using surfaces and regular grid (Sgrid) were built from all dataset available from exploration and exploitation including geological primary maps, 2D seismic cross-sections, and boreholes. The level of knowledge may differ from one site to another however those 3D resulting models were used to pilot additional field and exploration works. In the case of the Kupferschiefer, a sequential restoration-decompaction (4D geomodeling) from the Upper Permian to Cenozoic was conducted in the Lubin- Sieroszowice district of Poland. The results help in better understanding the various superimposed mineralization events which occurred through time in this copper deposit. A hydro-fracturing index was then calculated from the estimated overpressures during a Late Cretaceous-Early Paleocene up-lifting, and seems to correlate with the copper content distribution in the ore-series. These results are in agreement with an Early Paleocene paleomagnetic dating in the Germany part of the Kupferschiefer ore, and which perhaps represents the last mineralizing stages. Last, we discuss perspectives and make recommendations on applying 3&4 geomodeling in mineral resources appraisal. The above research received funding from the European Union's Seventh Framework Program under grant agreement 228559 (ProMine project).

The application of PGNAA borehole logging for copper grade estimation at Chuquicamata mine.

PubMed

Charbucinski, J; Duran, O; Freraut, R; Heresi, N; Pineyro, I

2004-05-01

The field trials of a prompt gamma neutron activation (PGNAA) spectrometric logging method and instrumentation (SIROLOG) for copper grade estimation in production holes of a porphyry type copper ore mine, Chuquicamata in Chile, are described. Examples of data analysis, calibration procedures and copper grade profiles are provided. The field tests have proved the suitability of the PGNAA logging system for in situ quality control of copper ore.

Mining and beneficiation of lunar ores

NASA Technical Reports Server (NTRS)

Bunch, T. E.; Williams, R. J.; Mckay, D. S.; Giles, D.

1979-01-01

The beneficiation of lunar plagioclase and ilmenite ores to feedstock grade permits a rapid growth of the space manufacturing economy by maximizing the production rate of metals and oxygen. A beneficiation scheme based on electrostatic and magnetic separation is preferred over conventional schemes, but such a scheme cannot be completely modeled because beneficiation processes are empirical and because some properties of lunar minerals have not been measured. To meet anticipated shipping and processing needs, the peak lunar mining rate will exceed 1000 tons/hr by the fifth year of operation. Such capabilities will be best obtained by automated mining vehicles and conveyor systems rather than trucks. It may be possible to extract about 40 kg of volatiles (60 percent H2O) by thermally processing the less than 20 micron ilmenite concentrate extracted from 130 tons of ilmenite ore. A thermodynamic analysis of an extraction process is presented.

Alchemy and mining: metallogenesis and prospecting in early mining books.

PubMed

Dym, Warren Alexander

2008-11-01

Historians have assumed that alchemy had a close association with mining, but exactly how and why miners were interested in alchemy remains unclear. This paper argues that alchemical theory began to be synthesised with classical and Christian theories of the earth in mining books after 1500, and served an important practical function. The theory of metals that mining officials addressed spoke of mineral vapours (Witterungen) that left visible markings on the earth's surface. The prospector searched for mineral ore in part by studying these indications. Mineral vapours also explained the functioning of the dowsing rod, which prospectors applied to the discovery of ore. Historians of early chemistry and mining have claimed that mining had a modernising influence by stripping alchemy of its theoretical component, but this paper shows something quite to the contrary: mining officials may have been sceptical of the possibility of artificial transmutation, but they were interested in a theory of the earth that could translate into prospecting knowledge.

Uranium Mining and Norm in North America-Some Perspectives on Occupational Radiation Exposure.

PubMed

Brown, Steven H; Chambers, Douglas B

2017-07-01

All soils and rocks contain naturally occurring radioactive materials (NORM). Many ores and raw materials contain relatively elevated levels of natural radionuclides, and processing such materials can further increase the concentrations of naturally occurring radionuclides. In the U.S., these materials are sometimes referred to as technologically-enhanced naturally occurring radioactive materials (TENORM). Examples of NORM minerals include uranium ores, monazite (a source of rare earth minerals), and phosphate rock used to produce phosphate fertilizer. The processing of these materials has the potential to result in above-background radiation exposure to workers. Following a brief review of the sources and potential for worker exposure from NORM in these varied industries, this paper will then present an overview of uranium mining and recovery in North America, including discussion on the mining methods currently being used for both conventional (underground, open pit) and in situ leach (ISL), also referred to as In Situ Recovery (ISR), and the production of NORM materials and wastes associated with these uranium recovery methods. The radiological composition of the NORM products and wastes produced and recent data on radiological exposures received by workers in the North American uranium recovery industry are then described. The paper also identifies the responsible government agencies in the U.S. and Canada assigned the authority to regulate and control occupational exposure from these NORM materials.

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2010 CFR

2010-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2012 CFR

2012-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2011 CFR

2011-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2013 CFR

2013-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

26 CFR 1.631-3 - Gain or loss upon the disposal of coal or domestic iron ore with a retained economic interest.

Code of Federal Regulations, 2014 CFR

2014-04-01

... domestic iron ore with a retained economic interest. 1.631-3 Section 1.631-3 Internal Revenue INTERNAL...) Sales and Exchanges § 1.631-3 Gain or loss upon the disposal of coal or domestic iron ore with a... disposes of coal (including lignite), or iron ore mined in the United States, held for more than 1 year (6...

3D geological to geophysical modelling and seismic wave propagation simulation: a case study from the Lalor Lake VMS (Volcanogenic Massive Sulphides) mining camp

NASA Astrophysics Data System (ADS)

Miah, Khalid; Bellefleur, Gilles

2014-05-01

The global demand for base metals, uranium and precious metals has been pushing mineral explorations at greater depth. Seismic techniques and surveys have become essential in finding and extracting mineral rich ore bodies, especially for deep VMS mining camps. Geophysical parameters collected from borehole logs and laboratory measurements of core samples provide preliminary information about the nature and type of subsurface lithologic units. Alteration halos formed during the hydrothermal alteration process contain ore bodies, which are of primary interests among geologists and mining industries. It is known that the alteration halos are easier to detect than the ore bodies itself. Many 3D geological models are merely projection of 2D surface geology based on outcrop inspections and geochemical analysis of a small number of core samples collected from the area. Since a large scale 3D multicomponent seismic survey can be prohibitively expensive, performance analysis of such geological models can be helpful in reducing exploration costs. In this abstract, we discussed challenges and constraints encountered in geophysical modelling of ore bodies and surrounding geologic structures from the available coarse 3D geological models of the Lalor Lake mining camp, located in northern Manitoba, Canada. Ore bodies in the Lalor lake VMS camp are rich in gold, zinc, lead and copper, and have an approximate weight of 27 Mt. For better understanding of physical parameters of these known ore bodies and potentially unknown ones at greater depth, we constructed a fine resolution 3D seismic model with dimensions: 2000 m (width), 2000 m (height), and 1500 m (vertical depth). Seismic properties (P-wave, S-wave velocities, and density) were assigned based on a previous rock properties study of the same mining camp. 3D finite-difference elastic wave propagation simulation was performed in the model using appropriate parameters. The generated synthetic 3D seismic data was then compared to the 3D multicomponent field survey data. Main features of the geological models, especially boundaries of main ore bodies were comparable in both data sets. This shows that the 3D geophysical model based on local geology and limited core samples is in fair agreement with the lithologic units confirmed from the field seismic survey data.

Location and stability analysis of the Michigamme Underground Mine for the US-41 re-alignment in Marquette County, Michigan.

DOT National Transportation Integrated Search

2008-08-01

A proposed realignment of US-41 near Michigamme, Michigan will be located over an abandoned underground iron ore : mine. The mine, known as the Michigamme Mine, was started in 1872 and closed in 1901. Initial mining operations : were started in seven...

EVIDENCE FOR METAL ATTENUATION IN ACID MINE WATER BY SULFATE REDUCTION, PENN MINE, CALAVERAS COUNTY, CALIFORNIA

EPA Science Inventory

The Penn Mine in Calaveras County, California, produced Cu from massive sulfide ores from 1861 to 1953. Mine wastes were removed to a landfill during the late 1990s, improving surface-water quality, but deep mine workings were not remediated and contain metalliferous water with p...

MINE WASTE TECHNOLOGY PROGRAM; PHOSPHATE STABILIZATION OF HEAVY METALS CONTAMINATED MINE WASTE YARD SOILS, JOPLIN, MISSOURI NPL SITE

EPA Science Inventory

This document summarizes the results of Mine Waste Technology Project 22-Phosphate Stabilization of Heavy Metals-Contaminated Mine Waste Yard Soils. Mining, milling, and smelting of ores near Joplin, Missouri, have resulted in heavy metal contamination of the area. The Joplin s...

14. OBLIQUE VIEW OF UPPER ORE BIN AND LOADING DECK, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. OBLIQUE VIEW OF UPPER ORE BIN AND LOADING DECK, LOOKING WEST. DETAIL OF SUPPORTING TIMBERS. THE LOCATION OF THIS ORE BIN IN RELATION TO THE MILL CAN BE SEEN IN MANY OF THE MILL OVERVIEWS. (CA-290-4 THROUGH CA-290-8). - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

40 CFR 440.93 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.93 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.73 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.73 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.25 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.25 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.45 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.45 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.55 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.55 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.95 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.95 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.65 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.65 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.92 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.92 Effluent limitations representing the degree of...

40 CFR 440.45 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.45 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.45 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.45 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.93 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.93 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.73 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.73 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.112 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.112 Effluent limitations representing the degree of...

40 CFR 440.112 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.112 Effluent limitations representing the degree of...

40 CFR 440.92 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.92 Effluent limitations representing the degree of...

40 CFR 440.65 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.65 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.112 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.112 Effluent limitations representing the degree of...

40 CFR 440.55 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.55 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.65 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.65 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.25 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.25 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.75 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.75 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.55 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.55 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.73 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.73 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.93 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.93 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.25 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.25 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.95 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.95 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.95 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.95 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.75 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.75 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.92 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.92 Effluent limitations representing the degree of...

40 CFR 440.75 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.75 Effluent limitations representing the degree of effluent reduction...

Earth Observations taken by the Expedition 22 Crew

NASA Image and Video Library

2010-01-14

ISS022-E-026137 (14 Jan. 2010) --- Open Pit Mines in southern Arizona are featured in this image photographed by an Expedition 22 crew member on the International Space Station. The State of Arizona is the United States? largest producer of the metal copper, primarily mined from ore bodies known as porphyry copper deposits. Copper is a good conductor of electricity and heat, and is a vital element of virtually all of our electronic devices and components. A porphyry copper deposit is a geological structure formed by crystal-rich magma moving upwards through pre-existing rock layers. As the magma cools and crystallizes, it forms an igneous rock with large crystals embedded in a fine-grained matrix, known as porphyry. Hot fluids circulate through the magma and surrounding rocks via fractures, depositing copper-bearing and other minerals in characteristic spatial patterns that signal the nature of the ore body to a geologist. The most common approach to extracting metal-bearing ore from a porphyry copper deposit is by open-pit mining. For more details, please refer to http://earth.jsc.nasa.gov/EarthObservatory/OpenPitMinesSouthernArizona.htm.

MINING AND PROCESSING AT THE MARY KATHLEEN

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1959-03-01

Ore mining and processing to the yellow cake at Mary Kathleen, Queensland, Australia, are described. The mining, crushlng, grinding, leaching, solids separation, ion exchange, purification, and final precipitation procedures and equipment are discussed in some detail. (T.R.H.)

Fact Sheet - Final Air Toxics Rule for Gold Mine Ore Processing and Production

EPA Pesticide Factsheets

Fact sheet summarizing main points of National Emissions Standards for Hazardous Air Pollutants for gold ore processing and production facilities, the seventh largest source of mercury air emission in the United States.

40 CFR 440.35 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.35 Effluent limitations representing the degree of...

40 CFR 440.105 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead, Zinc, Gold, Silver, and Molybdenum Ores Subcategory § 440.105 Effluent limitations...

40 CFR 440.112 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.112 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.112 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.112 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.15 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.15 Effluent limitations representing the degree of effluent reduction attainable...

40 CFR 440.105 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead, Zinc, Gold, Silver, and Molybdenum Ores Subcategory § 440.105 Effluent limitations...

40 CFR 440.92 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.92 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.105 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead, Zinc, Gold, Silver, and Molybdenum Ores Subcategory § 440.105 Effluent limitations...

40 CFR 440.35 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.35 Effluent limitations representing the degree of...

40 CFR 440.15 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.15 Effluent limitations representing the degree of effluent reduction attainable...

40 CFR 440.105 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead, Zinc, Gold, Silver, and Molybdenum Ores Subcategory § 440.105 Effluent limitations representing...

40 CFR 440.15 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.15 Effluent limitations representing the degree of effluent reduction attainable...

40 CFR 440.92 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.92 Effluent limitations representing the degree of effluent reduction...

40 CFR 440.35 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.35 Effluent limitations representing the degree of effluent...

40 CFR 440.35 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.35 Effluent limitations representing the degree of effluent...

40 CFR 440.35 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.35 Effluent limitations representing the degree of...

30 CFR 57.22203 - Main fan operation (I-C mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main fan operation (I-C mines). 57.22203... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22203 Main fan operation (I-C mines). Main fans shall be operated continuously while ore production is in progress. ...

40 CFR 440.140 - Applicability; description of the gold placer mine subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the gold... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine Subcategory § 440.140 Applicability; description of the gold placer mine subcategory. (a) The...

OVERVIEW OF UPPER TRAM TERMINAL, TRAM TRESTLE, AND PRIMARY ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OVERVIEW OF UPPER TRAM TERMINAL, TRAM TRESTLE, AND PRIMARY ORE BIN, LOOKING NORTHEAST. REMAINS OF A BLACKSMITH'S FORGE AND WORK CAN BE SEEN JUST BELOW THE ORE BIN (SEE CA-291-32 FOR DETAIL). ROCK FOUNDATIONS LOCATED JUST ABOVE THE ORE BIN AND ALONG THE FIRST RIDGELINE ARE TENT PADS. SEE CA-291-24 FOR IDENTICAL B&W NEGATIVE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

OVERVIEW OF UPPER TRAM TERMINAL, TRAM TRESTLE, AND PRIMARY ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OVERVIEW OF UPPER TRAM TERMINAL, TRAM TRESTLE, AND PRIMARY ORE BIN, LOOKING NORTHEAST. REMAINS OF A BLACKSMITH'S FORGE AND WORK CAN BE SEEN JUST BELOW THE ORE BIN (SEE CA-291-32 FOR DETAIL). ROCK FOUNDATIONS LOCATED JUST ABOVE THE ORE BIN AND ALONG THE FIRST RIDGELINE ARE TENT PADS. SEE CA-291-49 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Raman spectroscopy of efflorescent sulfate salts from Iron Mountain Mine Superfund Site, California.

PubMed

Sobron, Pablo; Alpers, Charles N

2013-03-01

The Iron Mountain Mine Superfund Site near Redding, California, is a massive sulfide ore deposit that was mined for iron, silver, gold, copper, zinc, and pyrite intermittently for nearly 100 years. As a result, both water and air reached the sulfide deposits deep within the mountain, producing acid mine drainage consisting of sulfuric acid and heavy metals from the ore. Particularly, the drainage water from the Richmond Mine at Iron Mountain is among the most acidic waters naturally found on Earth. The mineralogy at Iron Mountain can serve as a proxy for understanding sulfate formation on Mars. Selected sulfate efflorescent salts from Iron Mountain, formed from extremely acidic waters via drainage from sulfide mining, have been characterized by means of Raman spectroscopy. Gypsum, ferricopiapite, copiapite, melanterite, coquimbite, and voltaite are found within the samples. This work has implications for Mars mineralogical and geochemical investigations as well as for terrestrial environmental investigations related to acid mine drainage contamination.

Raman spectroscopy of efflorescent sulfate salts from Iron Mountain Mine Superfund Site, California

USGS Publications Warehouse

Sobron, Pablo; Alpers, Charles N.

2013-01-01

The Iron Mountain Mine Superfund Site near Redding, California, is a massive sulfide ore deposit that was mined for iron, silver, gold, copper, zinc, and pyrite intermittently for nearly 100 years. As a result, both water and air reached the sulfide deposits deep within the mountain, producing acid mine drainage consisting of sulfuric acid and heavy metals from the ore. Particularly, the drainage water from the Richmond Mine at Iron Mountain is among the most acidic waters naturally found on Earth. The mineralogy at Iron Mountain can serve as a proxy for understanding sulfate formation on Mars. Selected sulfate efflorescent salts from Iron Mountain, formed from extremely acidic waters via drainage from sulfide mining, have been characterized by means of Raman spectroscopy. Gypsum, ferricopiapite, copiapite, melanterite, coquimbite, and voltaite are found within the samples. This work has implications for Mars mineralogical and geochemical investigations as well as for terrestrial environmental investigations related to acid mine drainage contamination.

Flooding at Iron-Ore Mine, SE Brazil

NASA Image and Video Library

2015-11-14

On Nov. 5, 2015, a dam at an iron-ore mine in southeastern Brazil burst, sending a wall of water, clay-red mud and debris downstream, overwhelming several villages in the path as seen by NASA Terra spacecraft. The Germano mine is near the town of Mariana in Minas Gerais state. The region is seen in this image from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) instrument aboard NASA's Terra spacecraft was acquired Nov. 12, 2015, covers an area of 6.8 by 14.3 miles (11 by 23 kilometers), and is located at 20.2 degrees south, 43.5 degrees west. http://photojournal.jpl.nasa.gov/catalog/PIA20156

Distribution and Multivariate Pollution Risks Assessment of Heavy Metals and Natural Radionuclides Around Abandoned Iron-Ore Mines in North Central Nigeria

NASA Astrophysics Data System (ADS)

Isinkaye, Omoniyi Matthew

2018-02-01

The Itakpe abandoned iron-ore mines constitute the largest iron-ore deposits in Nigeria with an estimated reserve of about three million metric tons of ore. The present effort is a part of a comprehensive study to estimate the environmental and radiological health hazards associated with previous mining operations in the study area. In this regard, heavy metals (Fe, Zn, Cu, Cd, Cr, Mn, Pb, Ni, Co and As) and natural radionuclides (U, Th and K) were measured in rock, soil and water samples collected at different locations within the mining sites. Atomic absorption and gamma-ray spectrometry were utilized for the measurements. Fe, Mn, Zn, Cu, Ni, Cd, Cr, Co Pb and As were detected at varying concentrations in rock and soil samples. Cd, Cr, Pb and As were not detected in water samples. The concentrations of heavy metals vary according to the following pattern; rock ˃ soil ˃ water. The mean elemental concentrations of K, U and Th are 2.9%, 0.8 and 1.2 ppm and 1.3%, 0.7 and 1.7 ppm, respectively, for rock and soil samples. Pearson correlation analyses of the results indicate that the heavy metals are mostly negatively correlated with natural radionuclides in the study area. Cancer and non-cancer risks due to heavy metals and radiological hazards due to natural radionuclides to the population living within the vicinity of the abandoned mines are lower than acceptable limits. It can, therefore, be concluded that no significant environmental or radiological health hazard is envisaged.

Application of 57Fe Mössbauer spectroscopy as a tool for mining exploration of bornite (Cu5FeS4) copper ore

NASA Astrophysics Data System (ADS)

Gainov, R. R.; Vagizov, F. G.; Golovanevskiy, V. A.; Ksenofontov, V. A.; Klingelhöfer, G.; Klekovkina, V. V.; Shumilova, T. G.; Pen'kov, I. N.

2014-04-01

Nuclear resonance methods, including Mössbauer spectroscopy,are considered as unique techniques suitable for remote on-line mineralogical analysis. The employment of these methods provides potentially significant commercial benefits for mining industry. As applied to copper sulfide ores, Mössbauer spectroscopy method is suitable for the analysis noted. Bornite (formally Cu5FeS4) is a significant part of copper ore and identification of its properties is important for economic exploitation of commercial copper ore deposits. A series of natural bornite samples was studied by 57Fe Mössbauer spectroscopy. Two aspects were considered: reexamination of 57Fe Mössbauer properties of natural bornite samples and their stability irrespective of origin and potential use of miniaturized Mössbauer spectrometers MIMOS II for in-situ bornite identification. The results obtained show a number of potential benefits of introducing the available portative Mössbauer equipment into the mining industry for express mineralogical analysis. In addition, results of some preliminary 63,65Cu nuclear quadrupole resonance (NQR) studies of bornite are reported and their merits with Mössbauer techniques for bornite detection discussed.

Understanding Cu release into environment from Kure massive sulfide ore deposits, Kastamonu, NW Turkey

NASA Astrophysics Data System (ADS)

Demirel, Cansu; Sonmez, Seref; Balci, Nurgul

2014-05-01

Covering a wide range on the earth's crust, oxidation of metal sulfide minerals have vital environmental impacts on the aquatic environment, causing one of the major environmental problems known as acid mine drainage (AMD). Located in the Kastamonu province of the Western Black Sea region, Kure district is one of the major copper mining sites in Turkey. Mining activities in the area heads back to ancient times, such that operation is thought to be started with the Roman Empire. Currently, only the underground mining tunnels of Bakibaba and Asikoy are being operated. Thus, mining heaps and ores of those pyritic deposits have been exposed to the oxidative conditions for so long. As a result of weathering processes of past and recent heaps of the Kure volcanic massive sulfide deposits in addition to the main ore mineral (chalcopyrite), significant amount of metals, especially Cu, are being released into the environment creating undesirable environmental conditions. In order to elucidate Cu release mechanisms from Kure pyritic ore deposits and mining wastes, field and laboratory approaches were used. Surface water and sediment samples from the streams around the mining and waste sites were collected. Groundwater samples from the active underground mining site were also collected. Physical parameters (pH, Eh, T°C, and EC) of water samples were determined in situ and in the laboratory using probes (WTW pH 3110, WTW Multi 9310 and CRISON CM 35). Metal and ion concentrations of the water samples were analysed using ICP-MS and DR 2800 spectrophotometer, respectively. High Cu, Co, Zn and Fe concentrations were determined in the water samples with pH values ranging from 2.9- 4. Cu concentrions ranges from 345 ppm to 36 ppm in the water samples. Consistent with the water samples, high Cu, Fe, Zn and Co were also determined in the sediment samples. Laboratory chalcopyrite oxidation experiments under the conditions representing the field site were set up as biological and abiotic in order to elucidate Cu release from ore and wastes. Greater Cu release were measured from the biological experiments carried out with S and Fe oxidizers compared to those from the chemical experiments. Fe-oxide precipitation experiments carried out in the laboratory showed high Cu absorbtion into Fe-oxides produced by biological reactions carried out with Fe oxidizers. Overall, these preliminary experimental results showed that Cu release and migration from the source can be controlled by various microorganims which regulate S and Fe cycles in the field. Key words: Metal sulfide oxidation, Kure pyritic copper mines, AMD, Bioleaching, Secondary Fe-oxide precipitation

Blast from the Past: Pervasive Impact and Landscape-Scale Modification from Historical Mining Over 1000 Years in Central Sweden

NASA Astrophysics Data System (ADS)

Hansson, S.; Bindler, R.

2011-12-01

In the public consciousness Sweden is often viewed as a largely natural landscape. However, many parts of the landscape have undergone substantial changes. For example, in the historically and culturally important Bergslagen region in central Sweden, which played an important role in the economic development of Sweden since the medieval period, agriculture and mining have greatly transformed the landscape over the past 1000 years. Bergslagen is an ore-rich region characterized as a granite-porphyr belt formed 1900 Ma ago, with thousands of mines and mine pits, hundreds of furnaces, smelters and forges distributed throughout the area. Drawing on data from selected lake sediment records from different historical mining districts in Central Sweden (e.g. Norberg mining district - iron ores and Falun mining district - copper ores) the aim of this presentation is to show how small-scale but pervasively widespread mining and metallurgy, along with associated settlement, have transformed the surrounding landscape. These anthropogenic activities led to changes in sedimentation and erosion rates, forest structure, and also causing large-scale metal pollution and ecological changes in recipient watercourses and lakes. This historical pollution was oftentimes on a scale we associate with modern mining pollution. Our research is based on analyses of lake sediment records, which include multi-element analyses of minor and trace elements using XRF, mercury, carbon, and in some lakes also pollen and diatoms. In two lakes in Norberg, recent catastrophic failure (1991) of a sand magazine below a now closed mine led to significant contamination of the two downstream lakes, with Cu and Hg concentrations up to 1800 ppm and 1400 ppb, respectively. These concentrations are 50 and 20 times greater than natural background values. However, such elevated concentrations are also frequently found in sediments dated to the 16th-18th centuries. For example, in one lake in the Norberg iron mining district, Hg concentrations were as high as 1100 ppb in sediments from the 16th century - about 40 times greater than background level. Although the total concentrations of metals in the lake sediments in these areas have decreased since the peak in the 16th-17th centuries, due to declines in mining and metallurgy, and the complete cessation of activities since the mid-20th century, metal concentrations have remained elevated for more than 500 years. Already 500 years ago land use and mining in some cases led to cultural alkalization of lakes, but ultimately acidification of soils and lakes in areas where sulfide ores were mined and processed. Land use and mining pollution also altered biogeochemical conditions in downstream lakes, which have not returned to natural baseline levels although mining and metallurgy have ceased over the last two centuries. Seeing that these results are symptomatic of changes that potentially affected thousands of lakes in this large region of Sweden, we believe that this has important implications for other environmental and also archaeological studies in the area, particularly those aimed at establishing reference conditions for potential future exploitation of ores.

Thermal stress in North Western Australian iron ore mining staff.

PubMed

Peiffer, Jeremiah J; Abbiss, Chris R

2013-05-01

Demand for Australian mined iron ore has increased employment within this sector, thus exposing increased numbers of workers to the harsh Australian climate. This study examined the influence of hot (>30°C wet bulb globe temperature) environmental temperatures, consistent with working in North Western Australia, on iron ore mining staff. Core temperature, hydration status, perceived exertion, mood, and fatigue state were measured in 77 participants at three time points (pre-, mid-, and post-shift) during a normal 12-h shift at an open-cut iron ore mining/processing site (n = 31; Site1) and an iron ore processing/shipping site (n = 46; Site2). A significant effect for time was observed for core temperature with greater mean core temperatures measured mid-shift (37.5±0.4°C) and post-shift (37.6±0.3°C) compared with pre-shift values (37.0±0.5°C). All mean core temperature measures were lower than ISO7933 thresholds (38°C) for thermal safety. Mean hydration measures [urine-specific gravity (USG)] were greater at Site1 (1.029±0.006) compared with those at Site2 (1.021±0.007). Furthermore, both pre- and post-shift measures from Site1 and the post-shift measures from Site2 were greater than the threshold for dehydration (USG = 1.020). No differences were observed for mood or perceived exertion over time; however, measures of fatigue state were greater post-shift compared with pre- and mid-shift values for both sites. Our findings indicate that the majority of mine workers in North Western Australia are able to regulate work rate in hot environments to maintain core temperatures below ISO safety guidelines; however, 22% of workers reached or exceeded the safety guidelines, warranting further investigation. Furthermore, hydration practices, especially when off-work, appear inadequate and could endanger health and safety.

26. DETAIL OF STRUCTURAL COLLAPSE OF TOP FLOOR OF MILL, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. DETAIL OF STRUCTURAL COLLAPSE OF TOP FLOOR OF MILL, ABOVE ORE BIN, LOOKING WEST FROM TOP OF STAIRWAY IN CA-290-25. THE PIPE AT CENTER WAS USED TO SPREAD CRUSHED ORE COMING FROM THE JAW CRUSHER EVENLY TO ALL AREA OF THE ORE BIN BELOW. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

13. OBLIQUE VIEW OF UPPER ORE BIN, LOOKING WEST NORTHWEST. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. OBLIQUE VIEW OF UPPER ORE BIN, LOOKING WEST NORTHWEST. THIS ORE BIN WAS ADDED IN THE LATE 1930'S. IT IS TRAPAZOIDAL IN SHAPE, WIDER AT THE REAR THAN THE FRONT, AND DIVIDED INTO THREE BINS, EACH WITH ITS OWN CONTROL DOOR (SEE CA-290-15). - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN. CONVEYOR PLATFORM,TRAM TRESTLE, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN. CONVEYOR PLATFORM,TRAM TRESTLE, AND LOADING PLATFORM. LOOKING SOUTHWEST. THE HOLE IN THE ORE BIN FLOOR CAN BE SEEN, AND BALL MILL FOUNDATION AT LOWER LEFT CORNER. SEE CA-291-47(CT) FOR IDENTICAL COLOR TRANSPARENCY. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN, CONVEYOR PLATFORM TRAM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN, CONVEYOR PLATFORM TRAM TRESTLE, AND LOADING PLATFORM, LOOKING SOUTHWEST. THE HOLE IN THE ORE BIN FLOOR CAN BE SEEN, AND BALL MILL FOUNDATION AT LOWER LEFT CORNER. SEE CA-291-13 FOR IDENTICAL B&W NEGATIVE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Federal Guidance Report No. 8: Guidance for the Control of Radiation Hazards in Uranium Mining

EPA Pesticide Factsheets

This report contains background material used in the development of guidance concerning radiation protection in the mining of uranium ore, and seeks to provide guidance for long-term radiation protection in uranium mining.

Geochemistry of Standard Mine Waters, Gunnison County, Colorado, July 2009

USGS Publications Warehouse

Verplanck, Philip L.; Manning, Andrew H.; Graves, Jeffrey T.; McCleskey, R. Blaine; Todorov, Todor I.; Lamothe, Paul J.

2009-01-01

In many hard-rock-mining districts water flowing from abandoned mine adits is a primary source of metals to receiving streams. Understanding the generation of adit discharge is an important step in developing remediation plans. In 2006, the U.S. Environmental Protection Agency listed the Standard Mine in the Elk Creek drainage basin near Crested Butte, Colorado as a superfund site because drainage from the Standard Mine enters Elk Creek, contributing dissolved and suspended loads of zinc, cadmium, copper, and other metals to the stream. Elk Creek flows into Coal Creek, which is a source of drinking water for the town of Crested Butte. In 2006 and 2007, the U.S. Geological Survey undertook a hydrogeologic investigation of the Standard Mine and vicinity and identified areas of the underground workings for additional work. Mine drainage, underground-water samples, and selected spring water samples were collected in July 2009 for analysis of inorganic solutes as part of a follow-up study. Water analyses are reported for mine-effluent samples from Levels 1 and 5 of the Standard Mine, underground samples from Levels 2 and 3 of the Standard Mine, two spring samples, and an Elk Creek sample. Reported analyses include field measurements (pH, specific conductance, water temperature, dissolved oxygen, and redox potential), major constituents and trace elements, and oxygen and hydrogen isotopic determinations. Overall, water samples collected in 2009 at the same sites as were collected in 2006 have similar chemical compositions. Similar to 2006, water in Level 3 did not flow out the portal but was observed to flow into open workings to lower parts of the mine. Many dissolved constituent concentrations, including calcium, magnesium, sulfate, manganese, zinc, and cadmium, in Level 3 waters substantially are lower than in Level 1 effluent. Concentrations of these dissolved constituents in water samples collected from Level 2 approach or exceed concentrations of Level 1 effluent suggesting that water-rock interaction between Levels 3 and 1 can account for the elevated concentration of metals and other constituents in Level 1 portal effluent. Ore minerals (sphalerite, argentiferous galena, and chalcopyrite) are the likely sources of zinc, cadmium, lead, and copper and are present within the mine in unmined portions of the vein system, within plugged ore chutes, and in muck piles.

Contribution to understanding the post-mining landscape - Application of airborn LiDAR and historical maps at the example from Silesian Upland (Poland)

NASA Astrophysics Data System (ADS)

Gawior, D.; Rutkiewicz, P.; Malik, I.; Wistuba, M.

2017-11-01

LiDAR data provide new insights into the historical development of mining industry recorded in the topography and landscape. In the study on the lead ore mining in the 13th-17th century we identified remnants of mining activity in relief that are normally obscured by dense vegetation. The industry in Tarnowice Plateau was based on exploitation of galena from the bedrock. New technologies, including DEM from airborne LiDAR provide show that present landscape and relief of post-mining area under study developed during several, subsequent phases of exploitation when different techniques of exploitation were used and probably different types of ores were exploited. Study conducted on the Tarnowice Plateau proved that combining GIS visualization techniques with historical maps, among all geological maps, is a promising approach in reconstructing development of anthropogenic relief and landscape..

Use of structural geology in exploration for and mining of sedimentary rock-hosted Au deposits

USGS Publications Warehouse

Peters, Stephen G.

2001-01-01

Structural geology is an important component in regional-, district- and orebody-scale exploration and development of sedimentary rock-hosted Au deposits.Identification of timing of important structural events in an ore district allows analysis and classification of fluid conduits and construction of genetic models for ore formation.The most practical uses of structural geology deal with measurement and definition of various elements that comprise orebodies, which can then be directly applied to ore-reserve estimation,ground control,grade control, safety issues,and mine planning.District- and regional-scale structural studies are directly applicable to long-term strategic planning,economic analysis,and land ownership. Orebodies in sedimentary rock-hosted Au deposits are discrete, hypogene, epigenetic masses usually hosted in a fault zone,breccia mass, or lithologic bed or unit. These attributes allow structural geology to be directly applied to the mining and exploration of sedimentary rock-hosted Au deposits. Internal constituents in orebodies reflect unique episodes relating to ore formation.The main internal constituents in orebodies are ore minerals, gangue, and alteration minerals that usually are mixed with one another in complex patterns, the relations among which may be used to interpret the processes of orebody formation and control.Controls of orebody location and shape usually are due to structural dilatant zones caused by changes in attitude, splays, lithologic contacts,and intersections of the host conduit or unit.In addition,conceptual parameters such as district fabric,predictable distances, and stacking also are used to understand the geometry of orebodies.Controls in ore districts and location and geometry of orebodies in ore districts can be predicted to various degrees by using a number of qualitative concepts such as internal and external orebody plunges,district plunge, district stacking, conduit classification, geochemical, geobarometric and geothermal gradients, and tectonic warps. These concepts have practical and empirical application in most mining districts where they are of use in the exploration for ore, but are of such broad and general application that they may not represent known or inferred ore formation processes. Close spatial relation among some sedimentary rock- hosted Au deposits and their host structures suggests that the structures and the orebodies are genetically linked because they may have shared the same developmental history. Examples of probable syn-deformational genesis and structural control of sedimentary rock-hosted Au deposits are in the large Betze deposit in the Carlin trend, Nevada and in the Lannigou, Jinlongshan, and Maanqiao Au deposits, China.

The USGS Abandoned Mine Lands Initiative: Protecting and restoring the environment near abandoned mine lands

USGS Publications Warehouse

,

1999-01-01

The Abandoned Mine Lands (AML) Initiative is part of a larger strategy of the U.S. Department of the Interior and the U.S. Department of Agriculture to clean up Federal lands contaminated by abandoned mines.Thousands of abandond hard-rock metal mines (such as gold, copper, lead, and zinc) have left a dual legacy across the Western United States. They reflect the historic development of the west, yet at the same time represent a possible threat to human health and local ecosystems.Abandoned Mine Lands (AML) are areas adjacent to or affected by abandoned mines. AML's often contain unmined mineral deposits, mine dumps (the ore and rock removed to get to the ore deposits), and tailings (the material left over from the ore processing) that contaminate the surrounding watershed and ecosystem. For example, streams near AML's can contain metals and (or) be so acidic that fish and aquatic insects cannot live in them.Many of these abandoned hard-rock mines are located on or adjacent to public lands administered by the Bureau of Land Management, National Park Service, and U.S. Forest Service. These federal land management agencies and the USGS are committed to mitigating the adverse effects that AML's can have on water quality and stream habitats.The USGS AML Initiative began in 1997 and will continue through 2001 in two pilot watersheds - the Boulder River basin in southwestern Montana and the upper Animas River basin in southwestern Colorado. The USGS is providing a wide range of scientific expertise to help land managers minimize and, where possible, eliminate the adverse environmental effects of AML's. USGS ecologists, geologists, water quality experts, hydrologists, geochemists, and mapping and digital data collection experts are collaborating to provide the scientific knowledge needed for an effective cleanup of AML's.

Earth Observations taken by the Expedition 16 Crew

NASA Image and Video Library

2008-03-05

ISS016-E-031056 (3 March 2008) --- Cananea Copper Mine, Sonora, Mexico is featured in this image photographed by an Expedition 16 crewmember on the International Space Station. One of the largest open-pit copper mines in the world, the Cananea mine produced over 164,000 tons of copper in 2006. The mine is located approximately 40 kilometers south of the border between the USA (Arizona) and Mexico (Sonora). Copper and gold ores at Cananea are found in a porphyry copper deposit, a geological structure formed by crystal-rich magma moving upwards through pre-existing rock layers. A porphyry - an igneous rock with large crystals in a fine-grained matrix -- is formed as the magma cools and crystallizes. While crystallization is occurring, hot fluids can circulate through the magma and surrounding rocks via fractures. This hydrothermal alteration of the rocks typically forms copper-bearing and other minerals. Much of the Cananea mine's ore is concentrated in breccia pipes -- mineralized rod or chimney-shaped bodies that contain broken rock fragments. The active, two-kilometers-in-diameter Colorada Pit (top right) is recognizable in this image by the concentric steps or benches cut around its perimeter. These benches allow for access into the pit for extraction of ore and waste materials. Water (black) is visible filling the bottom of the pit, and several other basins in the surrounding area. The city of Cananea -- marked by its street grid -- is located to the northeast of the mine workings. A leachate reservoir is located to the east of the mine (lower left) for removal and evaporation of water pumped from the mine workings -- the bluish-white coloration of deposits near the reservoir suggests the high mineral content of the leachate. A worker strike halted mine operations in 2007.

40 CFR 440.24 - New Source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... reduction attainable by the application of the best available demonstrated technology (BADT). The concentration of pollutants discharged in mine drainage from mines producting bauxite ores shall not exceed...

40 CFR 440.24 - New Source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... reduction attainable by the application of the best available demonstrated technology (BADT). The concentration of pollutants discharged in mine drainage from mines producting bauxite ores shall not exceed...

40 CFR 440.24 - New Source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... attainable by the application of the best available demonstrated technology (BADT). The concentration of pollutants discharged in mine drainage from mines producting bauxite ores shall not exceed: Effluent...

40 CFR 440.24 - New Source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... reduction attainable by the application of the best available demonstrated technology (BADT). The concentration of pollutants discharged in mine drainage from mines producting bauxite ores shall not exceed...

40 CFR 440.24 - New Source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... attainable by the application of the best available demonstrated technology (BADT). The concentration of pollutants discharged in mine drainage from mines producting bauxite ores shall not exceed: Effluent...

40 CFR 440.41 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.41 Section 440.41 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.41 [Reserved] ...

40 CFR 440.111 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.111 Section 440.111 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.111 [Reserved] ...

40 CFR 440.111 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.111 Section 440.111 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.111 [Reserved] ...

40 CFR 440.111 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.111 Section 440.111 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.111 [Reserved] ...

40 CFR 440.111 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.111 Section 440.111 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.111 [Reserved] ...

40 CFR 440.111 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.111 Section 440.111 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory § 440.111 [Reserved] ...

40 CFR 440.91 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.91 Section 440.91 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.91 [Reserved] ...

40 CFR 440.51 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.51 Section 440.51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.51 [Reserved] ...

40 CFR 440.41 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.41 Section 440.41 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.41 [Reserved] ...

40 CFR 440.71 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.71 Section 440.71 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.71 [Reserved] ...

40 CFR 440.41 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.41 Section 440.41 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.41 [Reserved] ...

40 CFR 440.51 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.51 Section 440.51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.51 [Reserved] ...

40 CFR 440.11 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.11 Section 440.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.11 [Reserved] ...

40 CFR 440.71 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.71 Section 440.71 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.71 [Reserved] ...

40 CFR 440.41 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.41 Section 440.41 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.41 [Reserved] ...

40 CFR 440.51 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.51 Section 440.51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.51 [Reserved] ...

40 CFR 440.61 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.61 Section 440.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.61 [Reserved] ...

40 CFR 440.41 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.41 Section 440.41 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.41 [Reserved] ...

40 CFR 440.21 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.21 Section 440.21 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.21 [Reserved] ...

40 CFR 440.11 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.11 Section 440.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.11 [Reserved] ...

40 CFR 440.21 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.21 Section 440.21 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.21 [Reserved] ...

40 CFR 440.91 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.91 Section 440.91 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.91 [Reserved] ...

40 CFR 440.71 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.71 Section 440.71 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.71 [Reserved] ...

40 CFR 440.71 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.71 Section 440.71 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.71 [Reserved] ...

40 CFR 440.61 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.61 Section 440.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.61 [Reserved] ...

40 CFR 440.91 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.91 Section 440.91 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.91 [Reserved] ...

40 CFR 440.91 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.91 Section 440.91 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.91 [Reserved] ...

40 CFR 440.11 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.11 Section 440.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.11 [Reserved] ...

40 CFR 440.61 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.61 Section 440.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.61 [Reserved] ...

40 CFR 440.61 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.61 Section 440.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.61 [Reserved] ...

40 CFR 440.11 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.11 Section 440.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.11 [Reserved] ...

40 CFR 440.51 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.51 Section 440.51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.51 [Reserved] ...

40 CFR 440.101 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.101 Section 440.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead, Zinc, Gold, Silver, and Molybdenum Ores...

40 CFR 440.11 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.11 Section 440.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Iron Ore Subcategory § 440.11 [Reserved] ...

40 CFR 440.51 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.51 Section 440.51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Titanium Ore Subcategory § 440.51 [Reserved] ...

40 CFR 440.61 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.61 Section 440.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Tungsten Ore Subcategory § 440.61 [Reserved] ...

40 CFR 440.91 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.91 Section 440.91 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory § 440.91 [Reserved] ...

40 CFR 440.21 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.21 Section 440.21 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.21 [Reserved] ...

40 CFR 440.21 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.21 Section 440.21 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.21 [Reserved] ...

40 CFR 440.71 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.71 Section 440.71 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory § 440.71 [Reserved] ...

40 CFR 440.21 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.21 Section 440.21 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore Subcategory § 440.21 [Reserved] ...

40 CFR 440.101 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.101 Section 440.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead, Zinc, Gold, Silver, and Molybdenum Ores...

Offshore sediments record the history of onshore iron ore mining in Goa State, India.

PubMed

Sebastian, Tyson; Nath, B Nagender; Naik, Sangeeta; Borole, D V; Pierre, Salou; Yazing, Armoury Kazip

2017-01-30

Environmental magnetic and geochemical analyses combined with 210 Pb dating were carried out on a sediment core off Goa from Arabian Sea to reconstruct the sedimentation history of last three and a half centuries and to investigate the impact of onshore iron ore mining on the offshore sedimentation. A drastic increase in sedimentation rate and mineral magnetic concentration parameters divides the core into two units (1 & 2) at a depth of 41cm (1982CE). The high magnetic susceptibility values in Unit 1 sediments are coeval with increased iron ore production on land and illustrate the role of terrestrial mining on the increased offshore sedimentation. The early diagenetic signals were observed in Unit 2 of the core with low concentration parameters, coarse magnetic grain size and magnetically hard mineralogy. The geochemical data of the core also record the Little Ice Age (LIA) climatic events of Dalton and Maunder solar minima. Copyright © 2016 Elsevier Ltd. All rights reserved.

Meeting the challenge of the 80's cost reduction measures at the Iron Ore Company of Canada's Carol Project 1980-85

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tinto, I.A.

1985-01-01

The mining facilities, crushing plant, and concentrator of the Iron Ore Company of Canada were in operation by 1962. Today, the Carol Project has the capacity to produce 20 million tonnes of concentrate from which 10.5 million tonnes of pellets can be produced. The period 1980-85 spans a period of energy crisis, world-wide recession, and a consequent re-structuring of the North American steel industry as it struggles to survive in an arena of excess world stell making capacity, government subsidized industries, and the increasing competition from overseas and from developing countries. This paper reviews cost reduction programs implemented by themore » Iron Ore Company of Canada at its 'Carol Project' and emphasizes improvements made in labour productivity, energy conservation, mining strategy, quality control, and reduced cost through technical innovations over this difficult period. The cost reduction program is reviewed under the headings of labor productivity, energy conservation, mining strategy, technical innovations and quality control.« less

76 FR 20940 - Troy Mine, Incorporated, Troy Mine Revised Reclamation Plan, Kootenai National Forest, Lincoln...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-14

... mine. The ore is mined using the ``room-and-pillar method.'' The mine permit area covers 2,782 acres of.... Production stopped in 1993 and reinitiated in 2005 and is projected to continue for 3-5 years until the... evaluations necessary to complete design of reclamation elements that include a short-term water management...

Finalizing the Libby Action Plan Research Program

EPA Science Inventory

Libby, Montana is the location of a former vermiculite mine that operated from 1923 to 1990. The vermiculite ore from the mine co-existed with amphibole asbestos, referred to as Libby Amphibole Asbestos (LAA). Combined with the cessation of the asbestos mining and processing oper...

Development of computerized stocktaking system in mine surveying for ore mineral volume calculation in covered storehouses

NASA Astrophysics Data System (ADS)

Valdman, V. V.; Gridnev, S. O.

2017-10-01

The article examines into the vital issues of measuring and calculating the raw stock volumes in covered storehouses at mining and processing plants. The authors bring out two state-of-the-art high-technology solutions: 1 - to use the ground-based laser scanning system (the method is reasonably accurate and dependable, but costly and time consuming; it also requires the stoppage of works in the storehouse); 2 - to use the fundamentally new computerized stocktaking system in mine surveying for the ore mineral volume calculation, based on the profile digital images. These images are obtained via vertical projection of the laser plane onto the surface of the stored raw materials.

Comparison of the Ores of Swambo and Kalongwe with Shinkolobwe; LES GITES DE SWAMBO ET DE KALONGWE COMPARES A SHINKOLOBWE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Derriks, J.J.; Oosterbosch, R.

1959-10-31

Swambo is a small uraniferous deposit discovered recently to the east of Shimkolobwe. The mineralization found is localized in the breccia and the epontes'' of a transverse fault affecting a layer of the ore series. This layer is part of an anticline alignment which can be followed from Shinkolobwe to Kalongwe and the length of which is level with the schisto-dolomitric stratum. The discovery of the ore deposit was made hy the application of radiometric methods. A prelimiary series of borings showed that the usable mineralization extends 125 m under the surface. The development by mining has gone to themore » hydrostatic level. From a genetic viewpoint, the ore deposit is similar to that of Shinkolobwe, but it is less important. Kalongwe is a cupro-cobaltic ore deposit lying to the southeast of Kolwezi. The deposit is principally localized in a fault which intersects a small layer of the ore series. The greso-dolomitic stratum at the base of this series is impregnated with powdered black uranium oxides in the neighhorhood of the fault. The mineralization extends to 80 m of depth. The ore deposit was developed by mining to a depth of 42 m. The genesis of the deposit is comparable to that of Shinkolobwe, hat the Kalongwe ores are distinguished by the relative abundance of copper and the absence of nickel. (tr- auth)« less

Characterization of Uranium Ore Concentrate Chemical Composition via Raman Spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su, Yin-Fong; Tonkyn, Russell G.; Sweet, Lucas E.

Uranium Ore Concentrate (UOC, often called yellowcake) is a generic term that describes the initial product resulting from the mining and subsequent milling of uranium ores en route to production of the U-compounds used in the fuel cycle. Depending on the mine, the ore, the chemical process, and the treatment parameters, UOC composition can vary greatly. With the recent advent of handheld spectrometers, we have chosen to investigate whether either commercial off-the-shelf (COTS) handheld devices or laboratory-grade Raman instruments might be able to i) identify UOC materials, and ii) differentiate UOC samples based on chemical composition and thus suggest themore » mining or milling process. Twenty-eight UOC samples were analyzed via FT-Raman spectroscopy using both 1064 nm and 785 nm excitation wavelengths. These data were also compared with results from a newly developed handheld COTS Raman spectrometer using a technique that lowers background fluorescence signal. Initial chemometric analysis was able to differentiate UOC samples based on mine location. Additional compositional information was obtained from the samples by performing XRD analysis on a subset of samples. The compositional information was integrated with chemometric analysis of the spectroscopic dataset allowing confirmation that class identification is possible based on compositional differences between the UOC samples, typically involving species such as U3O8, α-UO2(OH)2, UO4•2H2O (metastudtite), K(UO2)2O3, etc. While there are clearly excitation λ sensitivities, especially for dark samples, Raman analysis coupled with chemometric data treatment can nicely differentiate UOC samples based on composition and even mine origin.« less

Distribution of uranium in the Bisbee district, Cochise County, Arizona

USGS Publications Warehouse

Wallace, Stewart R.

1956-01-01

The Bisbee district has been an important source of copper for many years, and substantial amounts of lead and zinc ore and minor amounts of manganese ore have been mined during certain periods. The copper deposits occur both as low-grade disseminated ore in the Sacramento Hill stock and as massive sulfide (and secondary oxide and carbonate) replacement bodies in Paleozoic limestones that are intruded by the stock and related igneous bodies. The lead-zinc production has come almost entirely from limestone replacement bodies. The disseminated ore exhibits no anomalous radioactivity, and samples from the Lavender pit contain from 0.002 to less than 0.001 percent equivalent uranium. The limestone replacement ores are distinctly radioactive and stoping areas can be readily distinguished from from unmineralized ground on the basis of radioactivity alone. The equivalent uranium content of the copper replacement ores ranges from 0.002 to 0.014 percent and averages about 0.005 percent; the lead-zinc replacement ores average more than 0.007 percent equivalent uranium. Most of the uranium in the copper ores of the district is retained in the smelter slag of a residual concentrate; the slag contains about 0.009 percent equivalent uranium. Uranium carried off each day by acid mine drainage is roughly equal to 1 percent of that being added to the slag dump. Although the total amount of uranium in the district is large, no minable concentrations of ore-grade material are known; samples of relatively high-grade material represent only small fractions of tons at any one locality.

40 CFR 440.31 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.31 Section 440.31 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440...

40 CFR 440.31 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.31 Section 440.31 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440...

40 CFR 440.31 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.31 Section 440.31 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.31...

40 CFR 440.31 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.31 Section 440.31 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440...

40 CFR 440.31 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.31 Section 440.31 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Uranium, Radium and Vanadium Ores Subcategory § 440.31...

Water requirements of the copper industry

USGS Publications Warehouse

Mussey, Orville Durey

1961-01-01

The copper industry in 1955 used about 330 million gallons of water per day in the mining and manufacturing of primary copper. This amount is about 0.3 percent of the total estimated withdrawals of industrial water in the United States in 1955. These facts were determined by a survey, in 1956, of the amount and chemical quality of the water used by the copper industry. A large part of this water was used in Arizona, Nevada, New Mexico, and Utah, where about five-sixths of the domestic copper is mined. Much of the remaining water use was near New York City where most of the electrolytic refineries are located, and the rest of the water was used in widely scattered places. A little more than 100,000 gallons of water per ton of copper was used in the production of copper from domestic ores. Of this amount about 70,000 gallons per ton was used in mining and concentrating the ore, and about 30,000 gallons per ton was used to reduce the concentrate to refined copper. In areas where water was scarce or expensive, the unit water use was a little more than half the average. About 60 mgd (million gallons per day) or 18 percent of the water was used consumptively, and nearly all of the consumptive use occurred in the water-short areas of the West. Of the water used in mining and manufacturing primary copper 75 percent was surface water and 25 percent was ground water, 89 percent of this water was self-supplied by the copper companies and 11 percent came from public supplies. Much of the water used in producing primary copper was of comparatively poor quality; about 46 percent was saline containing 1,000 ppm (parts per million) or more of dissolved solids and 54 percent was fresh. Water that is used for concentration of copper ores by flotation or even any water that comes in contact with the ore at any time before it reaches the flotation plant must be free of petroleum products because they interfere with the flotation process. The water used in mining and ore concentration was higher in dissolved solids and was harder than the water used in smelting and refining. Water used in mining and ore concentration had a median dissolved solids content of about 400 ppm and a median hardness (as CaCO3) of about 200 ppm. The median values for water used in smelting and refining were only half these amounts.

40 CFR 440.14 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... reduction attainable by applying the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines operated to obtain iron ore shall not exceed: Effluent...

40 CFR 440.14 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... reduction attainable by applying the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines operated to obtain iron ore shall not exceed: Effluent...

40 CFR 440.14 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... reduction attainable by applying the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines operated to obtain iron ore shall not exceed: Effluent...

40 CFR 440.14 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... attainable by applying the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines operated to obtain iron ore shall not exceed: Effluent characteristic...

Geological reconnaissance of some Uruguayan iron and manganese deposits in 1962

USGS Publications Warehouse

Wallace, Roberts Manning

1976-01-01

Three mineralized areas lie in an area near the town of Minas de Corrales in the Departamento de Rivera; they are the Cerro Amelia, the Cerro de Papagayo, and the Cerro Iman. The Cerro Amelia is composed of small bands of iron-rich rock separated by an amphibolitic or mafic rock. Selective mining would be necessary to extract the 31,000 tons per meter of depth of iron-rich rock that ranges from 15 to 40 percent metallic iron. The Cerro de Papagayo district contains many small, rich deposits of ferruginous manganese ore. The ratio of Mn to Fe varies widely within each small deposit as well as from deposit to deposit. Some ferruginous manganese ore contains 50-55 percent manganese dioxide. Although there are many thousands of tons of ore in the district, small-scale mining operations are imperative. One deposit, the Cerro Avestuz manganese mine, was visited. The manganese ore body lies within contorted highly metamorphosed itabirite that contains both hard low grade and soft high grade ferruginous manganese ores estimated to average 40 percent Mn. About 38,000 tons of manganese ore is present in this deposit. The Cerro Iman is a large block of itabirite that contains about 40 percent Fe. The grade is variable and probably runs from less than 35 percent Fe to more than 50 percent Fe. No exploration has been done on this deposit. It is recommended that the Cerro de Iman area be geologically mapped in detail, and that a geological reconnaissance be made of the area that is between the Cuchilla de Corrales and the Cuchilla de Areycua/Cuchilla del Cerro Pelado area.

Geochemistry and petrology of the indium-bearing polymetallic skarn ores at Pitkäranta, Ladoga Karelia, Russia

NASA Astrophysics Data System (ADS)

Valkama, M.; Sundblad, K.; Cook, N. J.; Ivashchenko, V. I.

2016-08-01

The historic mining district of Pitkäranta in the Ladoga region, Fennoscandian Shield, was exploited for Fe, Cu, Zn, Pb, Sn and Ag in the nineteenth to twentieth centuries. The Pitkäranta region is dominated by Palaeoproterozoic supracrustal rocks, which, together with gneissic Archaean dome structures, constitute an allochthonous terrane complex that amalgamated to the Archaean continent during the Svecokarelian orogeny at 1.9-1.8 Ga. This crustal complex was intruded by 1.8 Ga Late orogenic granites, 1.54 Ga anorogenic rapakivi granites and 1.45 Ga dolerites. The polymetallic skarn ores of Pitkäranta extend over a 25-km-long zone in Palaeoproterozoic supracrustal rocks and formed from hydrothermal solutions, which emanated from the anorogenic rapakivi granites and reacted with marble layers. Four major ore types are recognised after the dominating metal: Fe, Cu, Sn and Zn, respectively. These types are not restricted to individual mines or mine fields but represent end members in zonation patterns within each ore body. Pitkäranta was the second discovery site in the world for indium but has been without modern documentation for more than 75 years. The indium contents in the ores are up to 600 ppm, in most cases sphalerite-hosted. The only roquesite-bearing sample in this study had an indium grade of 291 ppm and an In/Zn ratio of 51 (close to the criteria for the limiting conditions for creating an In-rich mineral). The Pitkäranta ores have a potential for future small-scale exploitation, but all such plans are hampered by high contents if Bi, Cd and As.

Determining Prehistoric Mining Practices in Southeastern Europe Using Copper Isotopes

NASA Astrophysics Data System (ADS)

Powell, Wayne; Mathur, Ryan; Bankoff, H. Arthur; Bulatović, Aleksandar; Filipović, Vojislav

2017-04-01

Copper was first smelted from malachite at 5000 BCE in Serbia. There the Eneolithic (Copper Age) began with the production of small jewelry pieces and progressed to the casting of massive copper tools near its end, approximately 2000 years later. However, copper metallurgy in southeastern Europe ceased or significantly decreased in the later third millennium, several centuries before the Bronze Age began. Whether this metallurgical hiatus was the result a cultural shift or depletion of natural resources remains an ongoing subject of debate. It has been speculated that the marked reduction in metal production at the Eneolithic-Bronze Age transition was due to the exhaustion of surficial weathered oxide ores and the technical inability to smelt the underlying sulfide minerals. The behavior of copper isotopes in near-surface environments allows us to differentiate highly weathered oxide ores that occur at Earth's surface from non-weathered sulfide ores that occur at greater depth. The oxidation of copper generates fluids and associated minerals that are enriched in the 65Cu isotope. Thus, oxidative weathering of sulfide ores leads to the development of three stratified isotopic reservoirs for copper: 1) oxides above the water table that are enriched in 65Cu; 2) residual weathered sulfides minerals at the water table that are depleted in 65Cu; and 3) non-fractionated, non-weathered sulfide ore below the water table. And so, the transformative shift to sulfide-based metallurgy will be delineated by a significant decrease in δ65Cu in copper artifacts corresponding to the first use of 65Cu-depleted residual ore. The degree of variability of primary ore composition from numerable ore deposits would likely result in the overlap of copper isotope composition between populations of artifacts. Therefore, shifts in the mean copper isotope values and associated standard deviations would best reflect changes in ores use. A baseline value of -0.2‰ ±0.5 (1) was determined from an average of 164 published measurements from chalcopyrite and bornite from 8 epithermal and massive sulfide deposits. Twenty-two (88%) of Eneolithic artifacts (n=25) have values greater than this, whereas eight (73%) of the Early Bronze age artifacts (n=11) yield compositions less than -0.2‰. The mean of Middle Bronze Age, Late Bronze Age and Early Iron Age (n=86) cluster near -0.2‰. This pattern is consistent with a progression to the mining of ore assemblages from increasing depths through prehistory. The shift from 65Cu-enriched to 65Cu-depleted copper in artifacts across the Eneolithic-Bronze Age boundary at 2500 BCE indicates that accessible near-surface oxide ore reserves were depleted after approximately two millennia of mining, and that the beginning of the Bronze Age in the Balkans corresponded to the acquisition of pyrotechnology which allowed for the extraction of metals from sulfide minerals and the resumption of copper mining activity in the region.

The Nature and Use of Copper Reserve and Resource Data

USGS Publications Warehouse

Cox, Dennis P.; Wright, Nancy A.; Coakley, George J.

1981-01-01

Copper reserve, resource, and production data can be combined to produce disaggregated resource estimates and trends and, when combined with demand forecasts, can be used to predict future exploration and development requirements. Reserve estimates are subject to uncertainties due mainly to incomplete exploration and rapidly changing economic conditions. United States' reserve estimates in the past have been low mainly because knowledge of the magnitude of very large porphyry-copper deposits has been incomplete. Present estimates are considerably more reliable because mining firms tend to drill out deposits fully before mining and to release their reserve estimates to the public. The sum of reserves and past production yields an estimate of the total ore, total metal contained in ore, and average grade of ore originally in each of the deposits known in the United States. For most deposits, estimates of total copper in ore are low relative to the total copper in mineralized rock, and many estimates are strongly affected by the economic behavior of mining firms. A better estimate of the real distribution of copper contained in deposits can be obtained by combining past production data with resource estimates. Copper resource data are disaggregated into categories that include resources in undeveloped deposits similar to those mined in the past, resources in mines closed because of unfavorable economic conditions, resources in deep deposits requiring high-cost mining methods, arid resources in deposits located in areas where environmental restrictions have contributed to delays in development. The largest resource is located in the five largest porphyry deposits. These deposits are now being mined but the resources are not included in the present mining plan. Resources in this last category will not contribute to supply until some future time when ores presently being mined are depleted. A high correlation exists between total copper contained in deposits and annual production from deposits. This correlation can be used to predict roughly the potential production from undeveloped deposits. Large deposits annually produce relatively less metal per ton of copper contained than do medium and small deposits. Dividing reserves by annual production gives a depletion date for each copper mine. The sum of annual production capacity of all mines not yet depleted at any year of interest gives the minimum production capacity for that year. A graph of minimum production capacity by year combined with curves representing potential capacity from undeveloped identified resources can be compared with various demand scenarios to yield a measure of copper requirements from new sources. Since 1950 reserves have been developed in the United States at a rate of about 1 million tons of copper per year. Since 1960 the number of deposits developed per 10-year period has greatly increased without a commensurate increase in tonnage of copper. This is in part due to the fact that recent exploration successes have been increasingly represented by smaller and (or) lower grade deposits containing less metal.

40 CFR 440.44 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... attainable by the application of the best available demonstrated technology (BADT): (a) The concentration of pollutants discharged in mine drainage from mines, either open pit or underground, that produce mercury ores...

Robotic complex for the development of thick steeply-inclined coal seams and ore deposits

NASA Astrophysics Data System (ADS)

Nikitenko, M. S.; Malakhov, Yu V.; Neogi, Biswarup; Chakraborty, Pritam; Banerjee, Dipesu

2017-09-01

Proposal for the formulation of robotic complexes for steeply inclined coal seams as a basis of the supportive-enclosing walking module and power support with a controlled outlet for mining industry has been represented in this literature. In mining industry, the available resource base reserves and mineral deposits are concentrated deep down the earth crust leading towards a complicated geological condition i.e. abrupt ore bedding and steeply inclined strata with the high gas content and fire hazard of thick coal stratum, heading against an unfavorable and sometimes human labor life risk during subversive mining. Prevailing towards the development of effective robotic complexes based on the means of “unmanned technologies” for extraction of minerals from hard-to-reach deposits and make sure the safety of underground staff during sublevel mining technology.

Technical Report on the Behavior of Trace Elements, Stable Isotopes, and Radiogenic Isotopes During the Processing of Uranium Ore to Uranium Ore Concentrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marks, N. E.; Borg, L. E.; Eppich, G. R.

2015-07-09

The goals of this SP-1 effort were to understand how isotopic and elemental signatures behave during mining, milling, and concentration and to identify analytes that might preserve geologic signatures of the protolith ores. The impurities that are preserved through the concentration process could provide useful forensic signatures and perhaps prove diagnostic of sample origin.

Long-Term Planning for Open Pits for Mining Sulphide-Oxide Ores in Order to Achieve Maximum Profit

NASA Astrophysics Data System (ADS)

Kržanović, Daniel; Conić, Vesna; Stevanović, Dejan; Kolonja, Božo; Vaduvesković, Jovan

2017-12-01

Profitable exploitation of mineralised material from the earth's crust is a complex and difficult task that depends on a comprehensive planning process. Answering the question of how to plan production depends on the geometry of the deposit, as well as the concentration, distribution, and type of minerals in it. The complex nature of mineral deposits largely determines the method of exploitation and profitability of mining operations. In addition to unit operating costs and metal prices, the optimal recovery of and achievement of maximum profit from deposits of sulphide-oxide ores also depend, to a significant extent, on the level of technological recovery achieved in the ore processing procedure. Therefore, in defining a long-term development strategy for open pits, special attention must be paid to the selection of an optimal procedure for ore processing in order to achieve the main objective: maximising the Net Present Value (NPV). The effect of using two different processes, flotation processing and hydrometallurgical methods (bioleaching acid leaching), on determining the ultimate pit is shown in the case of the Kraku Bugaresku-Cementacija sulphide-oxide ore deposit in eastern Serbia. Analysis shows that the application of hydrometallurgical methods of processing sulphide-oxide ore achieved an increase in NPV of 20.42%.

Challenges facing the North American iron ore industry

USGS Publications Warehouse

Jorgenson, J.D.

2006-01-01

Summary: This report is derived from a presentation the author presented in late September at the Iron Ore 2005 Conference sponsored by The Australasian Institute of Mining and Metallurgy and held in Fremantle, Western Australia. Some slight revisions have been made for the new audience.

Ore Deposits Mined for Critical Elements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verplanck, Philip; Kelley, Karen

Summary of deposit types containing critical elements, including, cobalt, gallium, germanium, indium, niobium, PGE, REE, rhenium, selenium, and tellurium. Includes information about ore deposit type, mineralogy, geologic setting, example deposits and districts, concentration ranges per reported resource, grade, and additional deposit notes. References are also included.

Column bioleaching of low-grade mining ore containing high level of smithsonite, talc, sphaerocobaltite and azurite.

PubMed

Ilyas, Sadia; Chi, Ruan; Bhatti, H N; Bhatti, I A; Ghauri, M A

2012-03-01

Present work describes the bioleaching potential of metals from low-grade mining ore containing smithsonite, sphaerocobaltite, azurite and talc as main gangue minerals with adapted consortium of Sulfobacillus thermosulfidooxidans strain-RDB and Thermoplasma acidophilum. Bioleaching potential improved markedly by added energy source, acid preleaching and adaptation of microbial consortium with mixed metal ions. During whole leaching period including acid preleaching stage of 960 h and bioleaching stage of 212 days about 76% Co, 70% Zn, 84% Cu, 72% Ni and 63% Fe leached out.

Origin of high-grade gold ore, source of ore fluid components, and genesis of the Meikle and neighboring Carlin-type deposits, Northern Carlin Trend, Nevada

USGS Publications Warehouse

Emsbo, P.; Hofstra, A.H.; Lauha, E.A.; Griffin, G.L.; Hutchinson, R.W.

2003-01-01

The Meikle mine exploits one of the world's highest grade Carlin-type gold deposits with reserves of ca. 220 t gold at an average grade of 24.7 g/t. Locally, gold grades exceed 400 g/t. Several geologic events converged at Meikle to create these spectacular gold grades. Prior to mineralization, a Devonian hydrothermal system altered the Bootstrap limestone to Fe-rich dolomite. Subsequently the rocks were brecciated by faulting and Late Jurassic intrusive activity. The resulting permeability focused flow of late Eocene Carlin-type ore fluids and allowed them to react with the Fe-rich dolomite. Fluid inclusion data and mineral assemblages indicate that these fluids were hot (ca. 220??C),of moderate salinity (400 g/t. Petrographic observations, geochemical data, and stable isotope results from the Meikle mine and other deposits at the Goldstrike mine place important constraints on genetic models for Meikle and other Carlin-type gold deposits on the northern Carlin trend. The ore fluids were meteoric water (??D = -135???, ??18O = -5???) that interacted with sedimentary rocks at a water/rock ratio of ca. 1 and temperatures of ca. 220??C. The absence of significant silicification suggests that there was little cooling of the ore fluids during mineralization. These two observations strongly suggest that ore fluids were not derived from deep sources but instead flowed parallel to isotherms. The gold was transported by H2S (??34S = 9???), which was derived from Paleozoic sedimentary rocks. The presence of auriferous sedimentary exhalative mineralization in the local stratigraphic sequence raises the possibility that preexisting concentrations of gold contributed to the Carlin-type deposits. Taken together our observations suggest that meteoric water evolved to become an ore fluid by shallow circulation through previously gold- and sulfur-enriched rocks. Carlin-type gold deposits formed where these fluids encountered permeable, reactive Fe-rich rocks.

U.S.-Australia Civilian Nuclear Cooperation: Issues for Congress

DTIC Science & Technology

2010-12-01

Enrichment.......................................................................................................7 Uranium Mining and Milling...Issues for Congress Congressional Research Service 7 The nuclear fuel cycle begins with mining uranium ore and upgrading it to yellowcake. Because...uranium after the mining and milling stage. Commercial enrichment services are available in the United States, Europe, Russia, and Japan. Fuel

U.S.-Australia Civilian Nuclear Cooperation: Issues for Congress

DTIC Science & Technology

2010-09-30

7 Uranium Mining and Milling ................................................................................................8...cycle begins with mining uranium ore and upgrading it to yellowcake. Because naturally occurring uranium lacks sufficient fissile 235U to make fuel for...enrichment, and finally fabrication into fuel elements. Australia exports its uranium after the mining and milling stage. Commercial enrichment services

RISK ASSESSMENT AND REMEDIATION OF SOILS CONTAMINATED BY MINING AND SMELTING OF LEAD, ZINC AND CADMIUM

EPA Science Inventory

Mining nd smelting of Pb, Zn and Cd ores have caused widespread soil contamination in many countries. In locations with severe soil contamination, and strongly acidic soil or mine waste, ecosystems are devastated. Research has shown that An phytotoxicity, Pb-induced phosphate def...

MECHANISMS OF HEAVY METAL REMOVAL FROM ACID MINE DRAINAGE USING CHITIN

EPA Science Inventory

Acid Mine Drainage (AMD) emanating from inactive or active mine sites contains elevated levels of toxic heavy metals, which can have an adverse impact to the surrounding environment. The major pathway involved in generation of AMD is weathering of pyritic mineral ores, where in s...

Caves, mines and subterranean spaces: hazard and risk from exposure to radon.

NASA Astrophysics Data System (ADS)

Crockett, R. G. M.; Gillmore, G. K.

2009-04-01

Radon is a naturally occurring radioactive gas. It is colourless, odourless and chemically inert. The most hazardous isotope is 222Rn. Radon is formed in the natural environment by the radioactive decay of the element uranium (238U) and is a daughter product of daughter product of radium (226Ra). Uranium and radium are found, in differing degrees, in a wide range of rocks, soils (and building materials that are made from these). Radon concentrations in caves, e.g. limestone caves such as the Great Cave of Niah, Borneo, and caves in the Mendips and Peak District in the UK, has been documented and reveal that both (prehistoric) cave-dwellers and other users such as archaeologists are at risk from exposure to radon a naturally occurring radioactive gas. In general, but dependent on cave geometry and ventilation, radon concentration increases with increasing distance from the entrance, implying that the hazard also increases with distance from the entrance. With regard to mines and mining operations, as well as modern extraction of uranium and radium ores, both ores commonly occur alongside other metallic ores, e.g. silver at Schneeberg and Joachimsthal, and tin in Cornwall, and in some instances, waste from earlier metalliferious mining activity has itself been ‘mined' for uranium and/or radium ores. It is not solely the miners and other subterranean workers which are at risk, other workers and local inhabitants are also at risk. Also, that risk is not eliminated by protection against dust/airborne particulates: the risk from inhalation of radon is only reduced by reducing the inhalation of radon, i.e. use of breathing apparatus. Amongst the general population, radon is the second most significant cause of lung cancer behind tobacco smoking. Estimates vary but 6-9% of lung-cancers are attributable to radon and approximately 2% all cancer deaths are attributable to radon. These proportions will increase in higher-radon environments such as caves, mines and mining areas (via spoil heaps, settlement lagoons etc. containing uranium and radium). We here present an overview of the potential hazard presented by radon in subterranean spaces and by metalliferous mining activities. We also present some speculation as to evidence of (pre-) historic exposure to radon which might potentially exist in archaeological remains and oral traditions. Keywords: radon; caves; metalliferous mining; cave-dwellers; archaeologists.

36 CFR 9.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ore from a claim in the normal course of business of extraction for processing or marketing. It does... MANAGEMENT Mining and Mining Claims § 9.2 Definitions. The terms used in this part shall have the following...

Manganese

USGS Publications Warehouse

Cannon, William F.; Kimball, Bryn E.; Corathers, Lisa A.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Manganese is an essential element for modern industrial societies. Its principal use is in steelmaking, where it serves as a purifying agent in iron-ore refining and as an alloy that converts iron into steel. Although the amount of manganese consumed to make a ton of steel is small, ranging from 6 to 9 kilograms, it is an irreplaceable component in the production of this fundamental material. The United States has been totally reliant on imports of manganese for many decades and will continue to be so for at least the near future. There are no domestic reserves, and although some large low-grade resources are known, they are far inferior to manganese ores readily available on the international market. World reserves of manganese are about 630 million metric tons, and annual global consumption is about 16 million metric tons. Current reserves are adequate to meet global demand for several decades. Global resources in traditional land-based deposits, including both reserves and rocks sufficiently enriched in manganese to be ores in the future, are much larger, at about 17 billion metric tons. Manganese resources in seabed deposits of ferromanganese nodules and crusts are larger than those on land and have not been fully quantified. No production from seabed deposits has yet been done, but current research and development activities are substantial and may bring parts of these seabed resources into production in the future. The advent of economically successful seabed mining could substantially alter the current scenario of manganese supply by providing a large new source of manganese in addition to traditional land-based deposits.From a purely geologic perspective, there is no global shortage of proven ores and potential new ores that could be developed from the vast tonnage of identified resources. Reserves and resources are very unevenly distributed, however. The Kalahari manganese district in South Africa contains 70 percent of the world’s identified resources and about 25 percent of its reserves. South Africa, Brazil, and Ukraine together accounted for nearly 65 percent of reserves in 2013. The combination of total import reliance for manganese, the mineral commodity’s essential uses in our industrialized society, and the potential for supply disruptions because of the limited sources of the ore makes manganese among the most critical minerals for the United States.Manganese is the 12th most abundant element in Earth’s crust. Its concentration varies among common types of rocks, mostly in the range of from 0.1 to 0.2 percent. The highest quality manganese ores contain from 40 to 45 percent manganese. The formation of these ores requires specialized geologic conditions that concentrate manganese at several hundred times its average crustal abundance. The dominant processes in forming the world’s principal deposits take place in the oceans. As a result, most important manganese deposits occur in ancient marine sedimentary rocks that are now exposed on continents as a result of subsequent tectonic uplift and erosion. In many cases, other processes have further enriched these manganiferous sedimentary rocks to form some of today’s highest grade ores. Modern seabed resources of ferromanganese nodules cover vast areas of the present ocean floor and are still forming by complex interactions of marine microorganisms, manganese dissolved in seawater, and chemical processes on the seabed.Manganese is ubiquitous in soil, water, and air. It occurs most often in solid form but can become soluble under acidic conditions. Manganese mining, like any activity that disturbs large areas of Earth’s surface, has the potential to produce increases in manganese concentrations that could be harmful to humans or the environment if not properly controlled. Although manganese is an essential nutrient for humans and most other organisms, overexposure can lead to neurotoxicity in humans. Workers at manganese mining and processing facilities have the greatest potential to inhale manganese-rich dust. Without proper protective equipment, these workers may develop a permanent neurological disorder known as manganism. Each manganese mine is unique and presents its own suite of potential hazards and preventative measures. Likewise, various nations have their own sets of standards to ensure safe mining, isolation of mine waste, treatment of mine waters, and mine closure and restoration. Interest in mining trace metals contained in ferromanganese nodules and crusts on the seabed has increased rapidly in the past decade. Prime areas for future research include overcoming the technological challenges presented by mining as deep as 6,500 meters below sea level and understanding and mitigating the potential impacts of seabed mining on marine ecosystems.

40 CFR 440.114 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false New source performance standards (NSPS). [Reserved] 440.114 Section 440.114 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory...

40 CFR 440.114 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false New source performance standards (NSPS). [Reserved] 440.114 Section 440.114 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores Subcategory...

40 CFR 440.114 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false New source performance standards (NSPS). [Reserved] 440.114 Section 440.114 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores...

40 CFR 440.114 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false New source performance standards (NSPS). [Reserved] 440.114 Section 440.114 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores...

40 CFR 440.114 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false New source performance standards (NSPS). [Reserved] 440.114 Section 440.114 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Platinum Ores...

40 CFR 440.74 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false New source performance standards (NSPS). [Reserved] 440.74 Section 440.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore...

40 CFR 440.94 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false New source performance standards (NSPS). [Reserved] 440.94 Section 440.94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory...

40 CFR 440.74 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false New source performance standards (NSPS). [Reserved] 440.74 Section 440.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory...

40 CFR 440.74 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false New source performance standards (NSPS). [Reserved] 440.74 Section 440.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore...

40 CFR 440.94 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false New source performance standards (NSPS). [Reserved] 440.94 Section 440.94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore...

40 CFR 440.84 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false New source performance standards (NSPS). [Reserved] 440.84 Section 440.84 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore...

40 CFR 440.94 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false New source performance standards (NSPS). [Reserved] 440.94 Section 440.94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore...

40 CFR 440.94 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false New source performance standards (NSPS). [Reserved] 440.94 Section 440.94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore Subcategory...

40 CFR 440.84 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false New source performance standards (NSPS). [Reserved] 440.84 Section 440.84 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore...

40 CFR 440.94 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false New source performance standards (NSPS). [Reserved] 440.94 Section 440.94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Antimony Ore...

40 CFR 440.74 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false New source performance standards (NSPS). [Reserved] 440.74 Section 440.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore Subcategory...

40 CFR 440.74 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false New source performance standards (NSPS). [Reserved] 440.74 Section 440.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Nickel Ore...

40 CFR 440.84 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false New source performance standards (NSPS). [Reserved] 440.84 Section 440.84 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory...

40 CFR 440.84 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false New source performance standards (NSPS). [Reserved] 440.84 Section 440.84 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore Subcategory...

40 CFR 440.84 - New source performance standards (NSPS). [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false New source performance standards (NSPS). [Reserved] 440.84 Section 440.84 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Vanadium Ore...

25 CFR 215.11 - New leases where prior leases have been forfeited or abandoned.

Code of Federal Regulations, 2011 CFR

2011-04-01

... MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.11 New leases where prior leases... zinc ores have been discovered but the mines and mining operations have been abandoned and the leases... to the highest bidder. If the lead and zinc mining lease on said land be offered for sale at public...

3. VIEW OF EMPIRE STATE MINE WITH TAILING PILE IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. VIEW OF EMPIRE STATE MINE WITH TAILING PILE IN BOTTOM LEFT AND COLLAPSED ADIT LOCATED BELOW DARK SHADOWS IN FAR RIGHT/LOWER THIRD. COLLAPSED BUILDING AND PARTIAL VIEW OF ORE CHUTE/BIN IS VISIBLE ON HILLSIDE ABOVE TAILINGS. CAMERA POINTED NORTH/NORTHWEST. - Florida Mountain Mining Sites, Empire State Mine, West side of Florida Mountain, Silver City, Owyhee County, ID

The mining sector of Liberia: current practices and environmental challenges.

PubMed

Wilson, Samuel T K; Wang, Hongtao; Kabenge, Martin; Qi, Xuejiao

2017-08-01

Liberia is endowed with an impressive stock of mineral reserves and has traditionally relied on mining, namely iron ore, gold, and diamonds, as a major source of income. The recent growth in the mining sector has the potential to contribute significantly to employment, income generation, and infrastructure development. However, the development of these mineral resources has significant environmental impacts that often go unnoticed. This paper presents an overview of the Liberian mining sector from historical, current development, and economic perspectives. The efforts made by government to address issues of environmental management and sustainable development expressed in national and international frameworks, as well as some of the environmental challenges in the mining sector are analyzed. A case study was conducted on one of the iron ore mines (China Union Bong Mines Investment) to analyze the effects of the water quality on the local water environment. The results show that the analyzed water sample concentrations were all above the WHO and Liberia water standard Class I guidelines for drinking water. Finally the paper examines the application of water footprint from a life cycle perspective in the Liberian mining sector and suggests some policy options for water resources management.

Geology of the Midnite uranium mine, Stevens County, Washington; a preliminary report

USGS Publications Warehouse

Nash, J. Thomas; Lehrman, Norman J.

1975-01-01

The Midnite mine is one of only two mines in the United States currently producing uranium from discordant deposits in crystalline host rocks. Ore bodies are in metamorphosed steeply dipping Precambrian pelitic and calcareous rocks of a roof pendant adjacent to a Cretaceous(?) porphyritic quartz monzonite pluton. Production during 14 years, of operation has been about 8 million pounds of U3O8 from oxidized and reduced ores averaging 0.23 percent U3O8. Uranium deposits are generally tabular in form and dimensions range up to 380 m long, 210 m wide, and 50 m thick. Deposits are bounded on at least one side by unmineralized intrusive ribs of granitic rock, and thickest mineralized zones invariably occur at depressions in the intrusive contact. Upper limits of some deposits are nearly horizontal, and upper elevations of adjacent mineralized zones separated by ribs of granite are similar. Near surface ore is predominantly autunite, but ore at depth consists of pitchblende and coffinite with abundant pyrite and marcasite. Uranium minerals occur as .disseminations along foliation, replacements, and stockwork fracture-fillings. No stratigraphic controls on ore deposition are recognized. Rather, mineralized zones cut across lithologic boundaries if permeability is adequate. Most ore is in muscovite schist and mica phyllite, but important deposits occur in calc-silicate hornfels. Amphibolite sills and mid-Tertiary dacite dikes locally, carry ore where intensely fractured. High content of iron and sulfur, contained chiefly in FeS2, appear to be an important feature of favorable host rocks. Geometry of deposits, structural, and geochemical features suggest that uranium minerals were deposited over a span of time from late Cretaceous to late Tertiary. Ore occurs in but is not offset by a shear zone that displaces mid-Tertiary rocks.. Economic zones of uranium are interpreted to have been secondarily enriched in late Tertiary time by downward and lateral migration of uranium into permeable zones where deposition was influenced by ground water controls and minerals that could reduce or neutralize uranium-bearing solutions.

Small-scale studies of roasted ore waste reveal extreme ranges of stable mercury isotope signatures

NASA Astrophysics Data System (ADS)

Smith, Robin S.; Wiederhold, Jan G.; Jew, Adam D.; Brown, Gordon E.; Bourdon, Bernard; Kretzschmar, Ruben

2014-07-01

Active and closed Hg mines are significant sources of Hg contamination to the environment, mainly due to large volumes of mine waste material disposed of on-site. The application of Hg isotopes as source tracer from such contaminated sites requires knowledge of the Hg isotope signatures of different materials potentially released to the environment. Previous work has shown that calcine, the waste residue of the on-site ore roasting process, can exhibit distinct Hg isotope signatures compared with the primary ore. Here, we report results from a detailed small-scale study of Hg isotope variations in calcine collected from the closed New Idria Hg mine, San Benito County, CA, USA. The calcine samples exhibited different internal layering features which were investigated using optical microscopy, micro X-ray fluorescence, micro X-ray absorption spectroscopy (μ-XAS), and stable Hg isotope analysis. Significant Fe, S, and Hg concentration gradients were found across the different internal layers. Isotopic analyses revealed an extreme variation with pronounced isotopic gradients across the internal layered features. Overall, δ202Hg (±0.10‰, 2 SD) describing mass-dependent fractionation (MDF) ranged from -5.96 to 14.49‰, which is by far the largest range of δ202Hg values reported for any environmental sample. In addition, Δ199Hg (±0.06‰, 2 SD) describing mass-independent fractionation (MIF) ranged from -0.17 to 0.21‰. The μ-XAS analyses suggested that cinnabar and metacinnabar are the dominant Hg-bearing phases in the calcine. Our results demonstrate that the incomplete roasting of HgS ores in Hg mines can cause extreme mass-dependent Hg isotope fractionations at the scale of individual calcine pieces with enrichments in both light and heavy Hg isotopes relative to the primary ore signatures. This finding has important implications for the application of Hg isotopes as potential source tracers for Hg released to the environment from closed Hg mines and highlights the need for detailed source signature identification.

The brown iron ores of west-middle Tennessee: Chapter D in Contributions to economic geology (short papers and preliminary reports), 1927: Part I - Metals and nonmetals except fuels

USGS Publications Warehouse

Burchard, E.F.

1927-01-01

A study of the brown iron ore deposits of west-middle Tennessee has been carried on recently under a cooperative agreement between the Tennessee State Geological Survey and the United States Geological Survey. A detailed report on the subject was submitted in the spring of 1925 to the State Survey for publication as a bulletin, and the writing of the present report was completed in March, 1926. The field work was done mainly between October 22 and November 2, 1921, and April 26 and July 18, 1923; but in October, 1924, a visit was made to the mine at Napier. The writer was assisted in the field in 1921 by. R. W. Smith, assistant geologist, and in 1923 by C. C. Anderson, topographer, both of the Tennessee Survey. Mr. Wilbur A. Nelson, State geologist at the time the work was in progress, visited several mines with the writer and on these occasions as well as many times during the preparation of the report rendered helpful suggestions and guidance. Mr. H. D. Miser, of the United States Geological Survey, State geologist from September 1, 1925, to July 1, 1926, who is especially familiar with the southern part of this area, also cooperated heartily in the preparation of this report; and Mr. H. W. Davis, of the United States Bureau of Mines, compiled the statistical data on iron ore and pig iron. To all these gentlemen the writer desires to express his appreciation. Acknowledgments are also due to the officials and employees of the iron mining and manufacturing companies and to people living in the vicinity of inactive mining properties for their courteous attention and for the large amount of information furnished.In the present paper the general features of the region and of the iron-ore deposits are delineated, but only a few typical ore deposits in each county are described, as the State bulletin will contain detailed descriptions of all properties.

Nuclear forensic analysis of an unknown uranium ore concentrate sample seized in a criminal investigation in Australia

DOE PAGES

Keegan, Elizabeth; Kristo, Michael J.; Colella, Michael; ...

2014-04-13

In early 2009, a state policing agency raided a clandestine drug laboratory in a suburb of a major city in Australia. While searching the laboratory, they discovered a small glass jar labelled “Gamma Source” and containing a green powder. The powder was radioactive. This paper documents the detailed nuclear forensic analysis undertaken to characterize and identify the material and determine its provenance. Isotopic and impurity content, phase composition, microstructure and other characteristics were measured on the seized sample, and the results were compared with similar material obtained from the suspected source (ore and ore concentrate material). While an extensive rangemore » of parameters were measured, the key ‘nuclear forensic signatures’ used to identify the material were the U isotopic composition, Pb and Sr isotope ratios, and the rare earth element pattern. These measurements, in combination with statistical analysis of the elemental and isotopic content of the material against a database of uranium ore concentrates sourced from mines located worldwide, led to the conclusion that the seized material (a uranium ore concentrate of natural isotopic abundance) most likely originated from Mary Kathleen, a former Australian uranium mine.« less

Nuclear forensic analysis of an unknown uranium ore concentrate sample seized in a criminal investigation in Australia.

PubMed

Keegan, Elizabeth; Kristo, Michael J; Colella, Michael; Robel, Martin; Williams, Ross; Lindvall, Rachel; Eppich, Gary; Roberts, Sarah; Borg, Lars; Gaffney, Amy; Plaue, Jonathan; Wong, Henri; Davis, Joel; Loi, Elaine; Reinhard, Mark; Hutcheon, Ian

2014-07-01

Early in 2009, a state policing agency raided a clandestine drug laboratory in a suburb of a major city in Australia. During the search of the laboratory, a small glass jar labelled "Gamma Source" and containing a green powder was discovered. The powder was radioactive. This paper documents the detailed nuclear forensic analysis undertaken to characterise and identify the material and determine its provenance. Isotopic and impurity content, phase composition, microstructure and other characteristics were measured on the seized sample, and the results were compared with similar material obtained from the suspected source (ore and ore concentrate material). While an extensive range of parameters were measured, the key 'nuclear forensic signatures' used to identify the material were the U isotopic composition, Pb and Sr isotope ratios, and the rare earth element pattern. These measurements, in combination with statistical analysis of the elemental and isotopic content of the material against a database of uranium ore concentrates sourced from mines located worldwide, led to the conclusion that the seized material (a uranium ore concentrate of natural isotopic abundance) most likely originated from Mary Kathleen, a former Australian uranium mine. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Nuclear forensic analysis of an unknown uranium ore concentrate sample seized in a criminal investigation in Australia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keegan, Elizabeth; Kristo, Michael J.; Colella, Michael

In early 2009, a state policing agency raided a clandestine drug laboratory in a suburb of a major city in Australia. While searching the laboratory, they discovered a small glass jar labelled “Gamma Source” and containing a green powder. The powder was radioactive. This paper documents the detailed nuclear forensic analysis undertaken to characterize and identify the material and determine its provenance. Isotopic and impurity content, phase composition, microstructure and other characteristics were measured on the seized sample, and the results were compared with similar material obtained from the suspected source (ore and ore concentrate material). While an extensive rangemore » of parameters were measured, the key ‘nuclear forensic signatures’ used to identify the material were the U isotopic composition, Pb and Sr isotope ratios, and the rare earth element pattern. These measurements, in combination with statistical analysis of the elemental and isotopic content of the material against a database of uranium ore concentrates sourced from mines located worldwide, led to the conclusion that the seized material (a uranium ore concentrate of natural isotopic abundance) most likely originated from Mary Kathleen, a former Australian uranium mine.« less

Time-lapse seismic tomography using the data of microseismic monitoring network and analysis of mine-induced events, seismic tomography results and technological data in Pyhäsalmi mine, Finland

NASA Astrophysics Data System (ADS)

Nevalainen, Jouni; Kozlovskaya, Elena

2016-04-01

We present results of a seismic travel-time tomography applied to microseismic data from the Pyhäsalmi mine, Finland. The data about microseismic events in the mine is recorded since 2002 when the passive microseismic monitoring network was installed in the mine. Since that over 130000 microseismic events have been observed. The first target of our study was to test can the passive microseismic monitoring data be used with travel-time tomography. In this data set the source-receiver geometry is based on non-even distribution of natural and mine-induced events inside and in the vicinity of the mine and hence, is a non-ideal one for the travel-time tomography. The tomographic inversion procedure was tested with the synthetic data and real source-receiver geometry from Pyhäsalmi mine and with the real travel-time data of the first arrivals of P-waves from the microseismic events. The results showed that seismic tomography is capable to reveal differences in seismic velocities in the mine area corresponding to different rock types. For example, the velocity contrast between the ore body and surrounding rock is detectable. The velocity model recovered agrees well with the known geological structures in the mine area. The second target of the study was to apply the travel-time tomography to microseismic monitoring data recorded during different time periods in order to track temporal changes in seismic velocities within the mining area as the excavation proceeds. The result shows that such a time-lapse travel-time tomography can recover such changes. In order to obtain good ray coverage and good resolution, the time interval for a single tomography round need to be selected taking into account the number of events and their spatial distribution. The third target was to compare and analyze mine-induced event locations, seismic tomography results and mining technological data (for example, mine excavation plans) in order to understand the influence of mining technology to mining-induced seismicity. Acknowledgements: This study has been supported by ERDF SEISLAB project and Pyhäsalmi Mine Ltd.

75 FR 34205 - Petition for Waiver of Compliance

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-16

... cars used to haul ore from the mine at Ray Mine yard, in Ray, Arizona, to the Hayden smelter yard in... these proceedings by submitting written views, data, or comments. FRA does not anticipate scheduling a...

Remote Sensing Extraction of Stopes and Tailings Ponds in AN Ultra-Low Iron Mining Area

NASA Astrophysics Data System (ADS)

Ma, B.; Chen, Y.; Li, X.; Wu, L.

2018-04-01

With the development of economy, global demand for steel has accelerated since 2000, and thus mining activities of iron ore have become intensive accordingly. An ultra-low-grade iron has been extracted by open-pit mining and processed massively since 2001 in Kuancheng County, Hebei Province. There are large-scale stopes and tailings ponds in this area. It is important to extract their spatial distribution information for environmental protection and disaster prevention. A remote sensing method of extracting stopes and tailings ponds is studied based on spectral characteristics by use of Landsat 8 OLI imagery and ground spectral data. The overall accuracy of extraction is 95.06 %. In addition, tailings ponds are distinguished from stopes based on thermal characteristics by use of temperature image. The results could provide decision support for environmental protection, disaster prevention, and ecological restoration in the ultra-low-grade iron ore mining area.

RAMAN ANALYSIS OF FERTILIZER AND PLANT TISSUE EXTRACTS FOR PERCHLORATE CONTAMINATION

EPA Science Inventory

Recently, we and others found perchlorate at high levels (approximately 500 - 8000 mg/kg) in ~ 90% of 25+ fertilizers products (primarily lawn-and-garden type) with no known link to mined nitrate-bearing Chilean ore. This ore is used, albeit in small scale, in fertilizer product...

DETAIL VIEW OF FILTER PRESS REMAINS, BOILER, SECONDARY ORE BIN, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF FILTER PRESS REMAINS, BOILER, SECONDARY ORE BIN, TRAM TRESTLE AND WATER TANK, LOOKING NORTHWEST. HIS VIEW IS TAKEN FROM THE THIRD LEVEL OF THE MILL, NEARBY THE BLACKSMITH'S FORGE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

25 CFR 215.5 - Royalty rates.

Code of Federal Regulations, 2010 CFR

2010-04-01

... INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES... gross proceeds of all lead and zinc ores and concentrates extracted from the leased premises, the... royalty shall not be less than the highest and best obtainable market price of the lead and zinc ores and...

25 CFR 215.5 - Royalty rates.

Code of Federal Regulations, 2011 CFR

2011-04-01

... INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES... gross proceeds of all lead and zinc ores and concentrates extracted from the leased premises, the... royalty shall not be less than the highest and best obtainable market price of the lead and zinc ores and...

OBLIQUE DETAIL VIEW OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OBLIQUE DETAIL VIEW OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. THE JAW CRUSHER FOUNDATION CAN BE CLEARLY SEEN AT CENTER LEFT WITH A CONVEYOR TO CARRY CRUSHED ORE UP TO THE SECONDARY ORE BIN,LEFT. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Is outdoor work associated with elevated rates of cerebrovascular disease mortality? A cohort study based on iron-ore mining.

PubMed

Björ, Ove; Jonsson, Håkan; Damber, Lena; Burström, Lage; Nilsson, Tohr

2016-01-01

A cohort study that examined iron ore mining found negative associations between cumulative working time employed underground and several outcomes, including mortality of cerebrovascular diseases. In this cohort study, and using the same group of miners, we examined whether work in an outdoor environment could explain elevated cerebrovascular disease rates. This study was based on a Swedish iron ore mining cohort consisting of 13,000 workers. Poisson regression models were used to generate smoothed estimates of standardized mortality ratios and adjusted rate ratios, both models by cumulative exposure time in outdoor work. The adjusted rate ratio between employment classified as outdoor work ≥25 years and outdoor work 0-4 years was 1.62 (95 % CI 1.07-2.42). The subgroup underground work ≥15 years deviated most in occurrence of cerebrovascular disease mortality compared with the external reference population: SMR (0.70 (95 % CI 0.56-0.85)). Employment in outdoor environments was associated with elevated rates of cerebrovascular disease mortality. In contrast, work in tempered underground employment was associated with a protecting effect.

Restructuring the Uranium Mining Industry in Romania: Actual Situation and Prospects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Georgescu, P.D.; Petrescu, S.T.; Iuhas, T.F.

2002-07-01

Uranium prospecting in Romania has started some 50 years ago, when a bilateral agreement between Romania and the former Soviet Union had been concluded and a joint Romanian-Soviet enterprise was created. The production started in 1952 by the opening of some deposits from western Transylvania (Bihor and Ciudanovita). From 1962 the production has continued only with Romanian participation on the ore deposit Avram Iancu and from 1985 on the deposits from Eastern Carpathians (Crucea and Botusana). Starting with 1978 the extracted ores have been completely processed in the Uranium Ore Processing Plant from Feldioara, Brasov. Complying with the initial stipulationsmore » of the Nuclear National Program launched at the beginning of the 1980's, the construction of a nuclear power station in Cernavoda has started in Romania, using natural uranium and heavy water (CANDU type), having five units of 650 MW installed capacity. After 1989 this initial Nuclear National Program was revised and the construction of the first unit (number 1) was finalized and put in operation in 1996. In 2001 the works at the unit number 2 were resumed, having the year 2005 as the scheduled activating date. The future of the other 3 units, being in different construction phases, hasn't been clearly decided. Taking into consideration the exhaustion degree of some ore deposits and from the prospect of exploiting other ore deposits, the uranium industry will be subject of an ample restructuring process. This process includes workings of modernization of the mines in operation and of the processing plant, increasing the profitableness, lowering of the production costs by closing out and ecological rehabilitation of some areas affected by mining works and even new openings of some uraniferous exploitations. This paper presents the actual situation and the prospects of uranium mining industry on the base of some new technical and economical strategic concepts in accordance with the actual Romanian Program for Nuclear Energetics. (authors)« less

Application of Odor Sensors to Ore Sorting and Mill Feed Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michael G. Nelson

2005-08-01

Control of the feed provided to mineral processing facilities is a continuing challenge. Much effort is currently being devoted to overcoming these problems. These projects are usually described under the general headings of Mine-to-Mill Integration or Mine-Mill Optimization. It should be possible to combine the knowledge of ore type, mineralogy, and other characteristics (located in the mine modeling system), with the advanced capabilities of state-of-the-art mill control systems, to achieve an improved level of control in mineral processing that will allow optimization of the mill processes on an almost real-time basis. This is not happening because mill feed it ismore » often treated as a uniform material, when in reality it varies in composition and characteristics. An investigation was conducted to assess the suitability of odor sensors for maintaining traceability in ore production and processing. Commercially available sensors are now used in food processing, environmental monitoring, and other applications and can detect the presence of very small amounts (0.1-500 ppm) of some molecules. An assortment of such molecules could be used to ''tag'' blocks of ore as they are mined, according to their respective characteristics. Then, as the ore came into the mill, an array of ''electronic noses'' could be used to assess its characteristics in real time. It was found that the Cyranose 320{trademark}, a commercially available odor sensor, can easily distinguish among samples of rock marked with almond, cinnamon, citronella, lemon, and orange oils. Further, the sensor could detect mixtures of rocks marked with various combinations of these oils. Treatment of mixtures of galena and silica with odorant compounds showed no detrimental effects on flotation response in laboratory tests. Additional work is recommended to determine how this concept can be extended to the marking of large volumes of materials.« less

U.S.-Australia Civilian Nuclear Cooperation: Issues for Congress

DTIC Science & Technology

2010-07-07

Mining and Milling ................................................................................................7 Uranium Sales to India...carried out at Lucas Heights (see below). The nuclear fuel cycle begins with mining uranium ore and upgrading it to yellowcake. Because naturally... mining and milling stage. Commercial enrichment services are available in the United States, Europe, Russia, and Japan. Fuel fabrication services are

30 CFR 57.22003 - Mine category or subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the potential to liberate methane based on the history of the mine or the geological area in which the... to mines that operate within a combustible ore body and have the potential to liberate methane based... character, amount, duration, origin, and nature of methane emission and the presence of explosive dust and...

30 CFR 57.22003 - Mine category or subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the potential to liberate methane based on the history of the mine or the geological area in which the... to mines that operate within a combustible ore body and have the potential to liberate methane based... character, amount, duration, origin, and nature of methane emission and the presence of explosive dust and...

30 CFR 57.22003 - Mine category or subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the potential to liberate methane based on the history of the mine or the geological area in which the... to mines that operate within a combustible ore body and have the potential to liberate methane based... character, amount, duration, origin, and nature of methane emission and the presence of explosive dust and...

Analytical results for total-digestions, EPA-1312 leach, and net acid production for twenty-three abandoned metal-mining related wastes in the Boulder River watershed, northern Jefferson County, Montana

USGS Publications Warehouse

Fey, David L.; Desborough, George A.; Finney, Christopher J.

2000-01-01

IntroductionMetal-mining related wastes in the Boulder River basin study area in northern Jefferson County, Montana, have been implicated in their detrimental effects on water quality with regard to acid generation and toxic-metal solubilization during snow melt and storm water runoff events. This degradation of water quality is defined chiefly by the “Class 1 Aquatic Life Standards” that give limits for certain dissolved metal concentrations according to water alkalinity.Veins enriched in base- and precious metals were explored and mined in the Basin, Cataract Creek, and High Ore Creek drainages over a period of more than 70 years. Extracted minerals included galena, sphalerite, pyrite, chalcopyrite, tetrahedrite and arsenopyrite. Most of the metal-mining wastes in the study area were identified and described by the Montana Bureau of Mines and Geology. In 1997, the U.S. Geological Survey collected 20 composite samples of mine-dump or tailings waste from ten sites in the Basin and Cataract Creek drainages, and two samples from one site in the High Ore Creek drainage. Desborough and Fey presented data concerning acid generation potential, mineralogy, concentrations of certain metals by energy-dispersive X-ray fluorescence (EDXRF), and trace-element leachability of mine and exploration wastes from the ten sites of the Basin and Cataract Creek drainages. The present report presents total-digestion major- and trace-element analyses, net acid production (NAP), and results from the EPA-1312 synthetic precipitation leach procedure (SPLP) performed on the same composite samples from the ten sites from the Basin and Cataract Creek drainages, and two composite samples from the site in the High Ore Creek drainage.

Geology of the Copper King Mine area, Prairie Divide, Larimer County, Colorado (Part 1)

USGS Publications Warehouse

Sims, Paul Kibler; Phair, George

1952-01-01

The Copper King mine, in Larimer County, Colo., in the northern part of the Front Range of Colorado, was operated for a short time prior to World War II for copper and zino, but since 1949, when pitchblende was discovered on the mine dump, it has been worked for uranium. The bedrock in the mine area consists predominantly of pre-Cambrian (Silver Plums) granite with minor migmatite and metasediments--biotite-quartz-plagioclase gneiss, biotite schist, quartzite, amphibolite, amphibole skarn, and biotite skols. The metasediments occur as inclusions that trend northeast in the granite. This trend is essentially parallel to the prevailing foliation in the granite. At places the metasediments are crosscut sharply by the granite to form angular, partly discordant, steep-walled bodies in the granite. Faults, confined to a narrow zone that extends through the mine, cut both the pre-Cambrian rocks and the contained sulfide deposits. The Copper King fault, a breccia zone, contains a deposit of pitchblende; the other faults are believed to be later than the ore. The two types of mineral deposits--massive sulfide and pitchblende deposits--in the mine area, are of widely different mineralogy, age, and origin. The massive sulfide deposits are small and consist of pyrite, sphalerite, chalcopyrite, pyrrhotite, and in places magnetite in amphibole skarn, mice skols, and quartzite. The deposit at the Copper King mine has yielded small quantities of high-grade sphalerite ore. The massive sulfides are pyrometasomatic deposits of pre-Cambrian age. The pitchblende at the Copper King mine is principally in the Copper King vein, a tight, hard breccia zone that cuts through both granite and the massive sulfide deposit. A small part of the pitchblende is in small fractures near the vein and in boxwork pyrite adjacent to the vein; the post-ore faults, close to their intersection with the Copper King vein, contain some radioactive material, but elsewhere, so far as is known, they are barren. The pitchblende in the deposit forms a steeply plunging ore shoot that has a horizontal length of more than 50 feet and a vertical height of about 85 feet. The thickness of the ore shoot averages about 2 feet, but it ranges from a feather edge to about 4 feet. The hard pitch-blende is intimately intergrown with siderite; other gangue minerals include pyrite, quartz, and finely comminuted fragments of the wall rocks. The vein was repeatedly reopened during mineral deposition as shown by several stages of brecciation and recommended by the vein matter. The pitchblende deposit probably formed at intermediate temperatures and depths and, according to the Pb/U ratio, is about 60 million years old--an early Tertiary age.

The F'derik-Zouerate iron district: Mesoarchean and Paleoproterozoic iron formation of the Tiris Complex, Islamic Republic of Mauritania

USGS Publications Warehouse

Taylor, Cliff D.; Finn, Carol A.; Anderson, Eric D.; Bradley, Dwight C.; Joud, Mohamed; Taleb Mohamed, Ahmed; Horton, John D.; Johnson, Craig A.; Bouabdellah, Mohammed; Slack, John F.

2016-01-01

High-grade hematitic iron ores (of HIF, containing 60-65 wt%Fe) have been mined in Mauritania since 1952 from Superior-type iron deposits of the F'derik-Zouerate district.  Depletion of the high-grade ores in recent years has resulted in new exploration projects focused on lower-grade magnetite ores occurring in Algoma-type banded iron formation (of BIF, containing ca. 35 wt% Fe).  Mauritania is the seventeenth largest iron producer in the world and currently has about 1.1 Gt of crude iron ore reserves. 

77 FR 25206 - Proposed Extension of Existing Information Collection; Underground Retorts

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-27

... (those that operate within a combustible ore and either liberate methane or have the potential to liberate methane based on the history of the mine or the geological area in which the mine is located). At...

Small-scale and large-scale testing of photo-electrochemically activated leaching technology in Aprelkovo and Delmachik Mines

NASA Astrophysics Data System (ADS)

Sekisov, AG; Lavrov, AYu; Rubtsov, YuI

2017-02-01

The paper gives a description of tests and trials of the technology of heap gold leaching from rebellious ore in Aprelkovo and Delmachik Mines. Efficiency of leaching flowsheets with the stage-wise use of activated solutions of different reagents, including active forms of oxygen, is evaluated. Carbonate-peroxide solutions are used at the first stage of leaching to oxidize sulfide and sulfide-arsenide ore minerals to recover iron and copper from them. The second stage leaching uses active cyanide solutions to leach encapsulated and disperse gold and silver.

Sarcoid-resembling granulomatous lung disease secondary to occupational magnetite iron dust exposure.

PubMed

Xiao, Lewis; Kookana, Anil; McClure, Robert; Heraganahally, Subash

2018-08-01

Non-caseating granulomatous pulmonary conditions resembling sarcoidosis secondary to industrial/occupation exposure to magnetite iron ore dusts have been rarely documented in the literature. This is a case report of a 58-year-old blast crew member involved in iron ore/magnetite mining who presented with a 12-month history of chronic dry cough. High-resolution computed tomography revealed bilateral interstitial opacities. Lung biopsy demonstrated sarcoid-like granulomatous inflammation. Oral corticosteroid treatment improved the cough. Radiological features did not resolve despite treatment and yet remained stable following no subsequent exposure to iron mining dust.

Reconnaissance for radioactive materials in northeastern United States during 1952

USGS Publications Warehouse

McKeown, Francis A.; Klemic, Harry

1953-01-01

Reconnaissance for radioactive materials was made in parts of Maine, New York, New Jersey, and Pennsylvania. The primary objective was to examine the iron ore deposits and associated rocks in the Adirondack Mountains of New York and the Highlands of New Jersey. In addition, several deposits known or reported to contain radioactive minerals were examined to delimit their extent. Most of the deposits examined are not significant as possible sources of radioactive elements and the data pertaining to them are summarized in table form. Deposits that do warrant more description than can be given in table form are: Benson Mines, St. Lawrence County, N. Y.; Rutgers mine, Clinton County, N. Y.; Mineville Mines, Essex County, N. Y.l Canfield phosphate mine, Morris County, N. J.; Mullgan quarry, Hunterdon County, N. J.; and the Chestnut Hill-Marble Mountain area, Pennsylvania and New Jersey. The Old Bed in the Mineville district is the only deposit that may be economically significant. Apatite from Old Bed ore contains as much as 4.9 percent total rare earth. 0.04 percent thorium, and 0.018 percent uranium. Magnetite ore at the Rutgers mine contains radioactive zircon and apatite. Radioactivity measurements of outcrops and dump material show that the ore contains from 0.005 to 0.010 percent equivalent uranium. One sample of lean magnetite ore contains 0.006 percent equivalent uranium. Garnet-rich zones in the Benson Mines magnetite deposit contain as much as 0.017 equivalent uranium. Most of the rock and ore, however, contains about 0.005 percent equivalent uranium. Available data indicate that the garnet-rich zones are enriched in radioactive allanite. A shear zone in the Kittatinny limestone of Cambrian age at the Mulligan quarry contains uraniferous material. Radioactivity anomalies elsewhere in the quarry and in adjacent fields indicate that there may be other uraniferous shear zones. Assays of samples and measurements of outcrop radioactivity indicate that the uranium content of these zones is low; samples contain from 0.008 to 0.068 percent equivalent uranium. The anomalies, however, may indicate greater concentrations of uranium below surficial leached zones. The Chestnut Hill-Marble Mountain area contains radioactivity anomalies for about 2 miles along the strike of the contact of pre-Cambrian Pickering gneiss and Franklin limestone formations. In places this contact is injected with pegmatite, which probably was the source of the radioelements. The most favorable area for further study is at Marble Mountain, where a nearly continuous anomaly extends for about 1500 feet. Samples from part of this area contain as much as 0.044 percent equivalent uranium and 0.005 percent uranium. Radioactive hematite and florencite, in which thorium may have substituted for cerium, are the only radioactive minerals observed in the Marble Mountain area.

Geology and mining history of the Southeast Missouri Barite District and the Valles Mines, Washington, Jefferson, and St. Francois Counties, Missouri

USGS Publications Warehouse

Mugel, Douglas N.

2017-03-09

The Southeast Missouri Barite District and the Valles Mines are located in Washington, Jefferson, and St. Francois Counties, Missouri, where barite and lead ore are present together in surficial and near-surface deposits. Lead mining in the area began in the early 1700’s and extended into the early 1900’s. Hand mining of lead in the residuum resulted in widespread pits (also called shafts or diggings), and there was some underground mining of lead in bedrock. By the 1860’s barite was recovered from the residuum by hand mining, also resulting in widespread diggings, but generally not underground mines in bedrock. Mechanized open-pit mining of the residuum for barite began in the 1920’s. Barite production slowed by the 1980’s, and there has not been any barite mining since 1998. Mechanized barite mining resulted in large mined areas and tailings ponds containing waste from barite mills.The U.S. Environmental Protection Agency (EPA) has determined that lead is present in surface soils in Washington and Jefferson Counties at concentrations exceeding health-based screening levels. Also, elevated concentrations of barium, arsenic, and cadmium have been identified in surface soils, and lead concentrations exceeding the Federal drinking-water standard of 15 micrograms per liter have been identified in private drinking-water wells. Potential sources of these contaminants are wastes associated with barite mining, wastes associated with lead mining, or unmined natural deposits of barium, lead, and other metals. As a first step in helping EPA determine the source of soil and groundwater contamination, the U.S. Geological Survey (USGS), in cooperation with the EPA, investigated the geology and mining history of the Southeast Missouri Barite District and the Valles Mines.Ore minerals are barite (barium sulfate), galena (lead sulfide), cerussite (lead carbonate), anglesite (lead sulfate), sphalerite (zinc sulfide), smithsonite (zinc carbonate), and chalcopyrite (copper-iron sulfide). The Cambrian Potosi Dolomite is the most important formation for the ore deposits, followed by the Eminence Dolomite. Because galena, sphalerite, and barite are less soluble than dolomite, chemical weathering of the ore-bearing dolomite bedrock resulted in the concentration of ore minerals in the residuum. Most of the barite and lead mining was in the residuum, which averages 10 to 15 feet thick.Lead mining by French explorers may have begun in 1719 along Old Mines Creek at Cabanage de Renaudiere, which was followed shortly by the discovery of lead and the development of lead mines at Mine Renault (also called Forche a Renault Mine), Old Mines, and at other places along the Big River, Mineral Fork, and Forche a Renault Creek. Lead mining began sometime between 1775 and 1780 at Mine a Breton, the name of which was later changed to Potosi. Other mining areas were developed in the early part of the 19th century, including Fourche a Courtois (Palmer Mines), the French Diggings, and the Richwoods Mines. Zinc became a valuable resource after the Civil War, and the Valles Mines was an important supplier of zinc as well as lead, with at least some production up until the 1920’s. Lead mining declined in the early part of the 20th century as mining in the Old Lead Belt, Mine La Motte, and the Tri-State District expanded.The earliest lead mines were diggings in the residuum and were round holes (shafts) about 4 feet in diameter dug with pick and shovel about 15–20 feet deep, with drifts dug a short distance laterally from the bottom of the shafts. This mining process was repeated a short distance away until a large area was covered with pits. Some mining in bedrock began by about 1800, with shafts as deep as 170 feet and as much as several hundred feet of lateral drifts.Smelting of the lead ore to elemental lead was first done using a log furnace, which was inefficient; estimates have been made that only about 50 percent of the lead was recovered, and the remainder was lost to the ashes (slags) and to volatilization. Starting in 1798, ash furnaces were used to smelt the ashes from the log furnaces. These two furnaces were worked in tandem for many years but were gradually replaced by other furnaces, including the Scotch hearth. Estimates of lead recovery as high as 80–90 percent have been made for the Scotch hearth. By the mid-1870’s the air furnace was being used, also with estimated lead recovery as high as 80–90 percent. Zinc furnaces were built when zinc became a valuable commodity, but much of the zinc ore was shipped out of the area, either to a smelter in St. Louis, Missouri, or to other smelters.The total lead and zinc production from the Southeast Missouri Barite District and the Valles Mines is estimated at 180,000 tons of lead and 60,000 tons of zinc. An estimated 97,000 tons of lead and an estimated 120,000 tons of zinc were lost during smelting. The estimated losses do not include losses at the mine site during mining and preparation for smelting, such as the loss of fine-grained galena during hand cleaning or the discarding of zinc ore before its value was known, for which no estimates are available.Hand mining for barite in the residuum was active by at least the 1860’s and peaked from 1905 to the 1930’s when several thousand people were engaged in barite mining. Hand mining (diggings) and cleaning of the ore was done in much the same way as earlier lead mining, with the additional use of a rattle box to further clean the barite. Mechanized open-pit mining of old barite diggings began in 1924 to recover barite left behind by hand mining, and washing plants were used to clean the clay from the barite. Hand mining, however, continued to thrive, and washer plants began to close temporarily in 1931; nearly all of the barite produced before 1937 was by hand mining. By the 1940’s, however, all barite mining was mechanized.Mechanized mining used shovels powered by steam, gasoline, or electricity (and by the 1950’s draglines and front-end loaders) to mine the residuum. The ore was loaded onto rail cars (and by the 1940’s, trucks) for shipment to washer plants. Clay was removed from the barite using a log washer, and a jig was used to concentrate the barite. Overflow from the log washers was waste and went to a mud (tailings) pond. The coarse jig tailings went to tailings piles or were used as railroad ballast and, later, to create roads within the mine pit. Some barite was ground, depending on its final use, and some ground barite was bleached using a hot solution of sulfuric acid to remove impurities such as iron minerals and lead sulfide (galena). An earlier bleaching process used lead-lined tanks.Large quantities of water were required for milling the barite; some was recirculated water and the remainder came from dammed streams or was pumped from wells. Tailings and wastewater were impounded behind dikes that were built across small valleys and were increased in height as necessary using washer waste and any overburden that had been stripped. In some cases, dikes were built across valleys that had already been mined for barite.The total production of barite from the Southeast Missouri Barite District and the Valles Mines is estimated to have been about 13.1 million tons. Most of the barite production was from Washington County. Hand mining and processing of barite was inefficient. Estimates of barite recovery range from less than one-fourth to about one-half because pillars between the shafts in the residuum needed to be left unmined for stability. With mechanized mining, large amounts of barite were lost during the milling process. It has been estimated that about 30 percent of the barite was lost and that about two-thirds of the lost barite was fine-grained and was discharged to the tailings ponds. Some galena was lost to the tailings ponds.A 1972 inventory of tailings ponds by the Missouri Geological Survey identified 67 ponds in the Southeast Missouri Barite District (there are more than this currently documented). Results from samples from four ponds that were drilled were used to estimate that the 67 ponds contained almost 39 million tons (or cubic yards) of tailings averaging about 5 percent barite, for a potential reserve of 1.935 million tons of barite.It is not known how much lead was removed during barite mining, either by hand or mechanized mining and processing, how much lead was recovered, or how much lead went as fines to the tailing ponds or as coarse material to mine roads or was otherwise lost.

Public exposure to hazards associated with natural radioactivity in open-pit mining in Ghana.

PubMed

Darko, E O; Faanu, A; Awudu, A R; Emi-Reynolds, G; Yeboah, J; Oppon, O C; Akaho, E H K

2010-01-01

The results of studies carried out on public exposure contribution from naturally occurring radioactive materials (NORMS) in two open-pit mines in the Western and Ashanti regions of Ghana are reported. The studies were carried out under International Atomic Energy Agency-supported Technical Co-operation Project GHA/9/005. Measurements were made on samples of water, soil, ore, mine tailings and air using gamma spectrometry. Solid-state nuclear track detectors were used for radon concentration measurements. Survey was also carried out to determine the ambient gamma dose rate in the vicinity of the mines and surrounding areas. The effective doses due to external gamma irradiation, ingestion of water and inhalation of radon and ore dusts were calculated for the two mines. The average annual effective dose was found to be 0.30 +/- 0.06 mSv. The result was found to be within the levels published by other countries. The study provides a useful information and data for establishing a comprehensive framework to investigate other mines and develop guidelines for monitoring and control of NORMS in the mining industry and the environment as a whole in Ghana.

Biogenic non-crystalline U(IV) revealed as major component in uranium ore deposits

NASA Astrophysics Data System (ADS)

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly D.; Roebbert, Yvonne; Weyer, Stefan; Bernier-Latmani, Rizlan; Borch, Thomas

2017-06-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U(VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U(IV) generated through biologically mediated U(VI) reduction is the predominant U(IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (~58-89%) of U is bound as U(IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U(VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotope signatures, consistent with largely biotic reduction of U(VI) to U(IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U(IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.

Biogenic non-crystalline U(IV) revealed as major component in uranium ore deposits

PubMed Central

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly D.; Roebbert, Yvonne; Weyer, Stefan; Bernier-Latmani, Rizlan; Borch, Thomas

2017-01-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U(VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U(IV) generated through biologically mediated U(VI) reduction is the predominant U(IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (∼58-89%) of U is bound as U(IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U(VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotope signatures, consistent with largely biotic reduction of U(VI) to U(IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U(IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment. PMID:28569759

Biogenic non-crystalline U (IV) revealed as major component in uranium ore deposits

DOE PAGES

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly D.; ...

2017-06-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U (VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U (IV) generated through biologically mediated U (VI) reduction is the predominant U (IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (~58-89%) of U is bound as U (IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U (VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotopemore » signatures, consistent with largely biotic reduction of U (VI) to U (IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U (IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.« less

Biogenic non-crystalline U(IV) revealed as major component in uranium ore deposits.

PubMed

Bhattacharyya, Amrita; Campbell, Kate M; Kelly, Shelly D; Roebbert, Yvonne; Weyer, Stefan; Bernier-Latmani, Rizlan; Borch, Thomas

2017-06-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U (VI) ) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U (IV)  generated through biologically mediated U (VI)  reduction is the predominant U (IV)  species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (∼58-89%) of U is bound as U (IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U (VI) represent only minor components. The uranium deposit exhibited mostly 238 U-enriched isotope signatures, consistent with largely biotic reduction of U (VI) to U (IV) . This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U (IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.

Biogenic non-crystalline U (IV) revealed as major component in uranium ore deposits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly D.

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U (VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U (IV) generated through biologically mediated U (VI) reduction is the predominant U (IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (~58-89%) of U is bound as U (IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U (VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotopemore » signatures, consistent with largely biotic reduction of U (VI) to U (IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U (IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.« less

Biogenic non-crystalline U(IV) revealed as major component in uranium ore deposits

USGS Publications Warehouse

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly; Roebbert, Yvonne; Weyer, Stefan; Bernier-Latmani, Rizlan; Borch, Thomas

2017-01-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U(VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U(IV) generated through biologically mediated U(VI) reduction is the predominant U(IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (∼58-89%) of U is bound as U(IV)to C-containing organic functional groups or inorganic carbonate, while uraninite and U(VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotope signatures, consistent with largely biotic reduction of U(VI) to U(IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U(IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.

77 FR 67362 - Application for Final Commitment for a Long-Term Loan or Financial Guarantee in Excess of $100...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-09

... transaction: To support the export of mining trucks and bulldozers to Ukraine. Brief non-proprietary description of the anticipated use of the items being exported: To mine iron ore in Ukraine To the extent that... industry. Parties: Principal Supplier: Caterpillar Inc. Obligors: OJSC Ferrexpo Poltava Mining, Ukraine...

ARSENIC SPECIATION, SEASONAL TRANSFORMATIONS, AND CO-DISTRIBUTION WITH IRON IN A MINE WASTE-INFLUENCED PALUSTRINE EMERGENT WETLAND. (R825399)

EPA Science Inventory

Arsenic is commonly associated with mined ores and thus may be detrimental to naturally occurring wetlands that reside in mine waste-impacted regions. Understanding the relationship between Fe and As in both the aqueous and solid phase is critical for assessing the risk As impose...

Gold Mining in Papua New Guinea: A Curricular Omission?

ERIC Educational Resources Information Center

Palmer, W. P.

1989-01-01

What criteria should be used to include or exclude particular topics within a country's science curriculum? It will be argued here that gold/gold mining is a suitable and relevant topic for inclusion in PNG's science curricula and suggestions towards achieving that end will be offered. The teaching of the mining of copper ore and the metal's…

40 CFR 440.33 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

...) The concentration of pollutants discharged in mine drainage from mines, either open-pit or underground, that produce uranium ore, including mines using in-situ leach methods, shall not exceed: Effluent...). Except as provided in subpart L of this part and 40 CFR 125.30 through 125.32, any existing point source...

40 CFR 440.33 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... concentration of pollutants discharged in mine drainage from mines, either open-pit or underground, that produce uranium ore, including mines using in-situ leach methods, shall not exceed: Effluent characteristic... provided in subpart L of this part and 40 CFR 125.30 through 125.32, any existing point source subject to...

40 CFR 440.33 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

...) The concentration of pollutants discharged in mine drainage from mines, either open-pit or underground, that produce uranium ore, including mines using in-situ leach methods, shall not exceed: Effluent...). Except as provided in subpart L of this part and 40 CFR 125.30 through 125.32, any existing point source...

40 CFR 440.33 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... concentration of pollutants discharged in mine drainage from mines, either open-pit or underground, that produce uranium ore, including mines using in-situ leach methods, shall not exceed: Effluent characteristic... provided in subpart L of this part and 40 CFR 125.30 through 125.32, any existing point source subject to...

Hydrologic Investigations Concerning Lead Mining Issues in Southeastern Missouri

USGS Publications Warehouse

Kleeschulte, Michael J.

2008-01-01

Good stewardship of our Nation's natural resources demands that the extraction of exploitable, minable ore deposits be conducted in harmony with the protection of the environment, a dilemma faced by many land and water management agencies in the Nation's mining areas. As ore is mined, milled, and sent to the smelter, it leaves footprints where it has been in the form of residual trace metals. Often these footprints become remnants that can be detrimental to other natural resources. This emphasizes the importance of understanding the earth's complex physical and biological processes and their interactions at increasingly smaller scales because subtle changes in one component can substantially affect others. Understanding these changes and resulting effects requires an integrated, multidisciplinary scientific approach. As ore reserves are depleted in one area, additional exploitable deposits are required to replace them, and at times these new deposits are discovered in previously unmined areas. Informed decisions concerning resource management in these new, proposed mining areas require an understanding of the potential consequences of the planned mining actions. This understanding is usually based on knowledge that has been accumulated from studying previously mined areas with similar geohydrologic and biologic conditions. If the two areas experience similar mining practices, the information should be transferable. Lead and zinc mining along the Viburnum Trend Subdistrict of southeastern Missouri has occurred for more than 40 years. Additional potentially exploitable deposits have been discovered 30 miles to the south, within the Mark Twain National Forest. It is anticipated that the observation of current (2008) geohydrologic conditions in the Viburnum Trend can provide insight to land managers that will help reasonably anticipate the potential mining effects should additional mining occur in the exploration area. The purpose of this report is to present a compilation of previously unpublished information that was collected as part of a larger multidisciplinary study of lead mining issues in southeastern Missouri. The report resulted from the application of a multidisciplinary approach to investigate current hydrologic and biologic conditions in streams of the Viburnum Trend and the exploration area in the Mark Twain National Forest.

The recovery of gold from refractory ores by the use of carbon-in-chlorine leaching

NASA Astrophysics Data System (ADS)

Greaves, John N.; Palmer, Glenn R.; White, William W.

1990-09-01

Recently, the U.S. Bureau of Mines examined the recovery of gold by chlorination of refractory carbonaceous and sulfidic ores, comparing various treatment methods in which a ground ore pulp is contacted with chlorine gas and activated carbon is added to the pulp for a carbon-in-chlorine leach (CICL). The objective of this research was to demonstrate the basic feasibility of CICL technology. Results showed that the organic carbon deactivating environment of CICL lowers, but does not eliminate, the adsorption of gold on activated carbon. In this environment, the refractory ore is altered, and gold is extracted and then recovered on activated carbon. With highly carbonaceous ores, CICL achieved a higher recovery than with primarily sulfidic refractory ores. Basic cyanide amenability testing of two carbonaceous ores achieved recoveries of only 5.5% and 46%. With CICL treatment, recoveries on carbon were 90% and 92%.

Whole body vibration exposure in heavy earth moving machinery operators of metalliferrous mines.

PubMed

Vanerkar, A P; Kulkarni, N P; Zade, P D; Kamavisdar, A S

2008-08-01

As mining operations get mechanized, the rate of profit generation increases and so do the rate of occupational hazards. This study deals with one such hazard - occupational vibration. The present study was carried out to determine the whole body vibration (WBV) exposure of the heavy earth moving machinery (HEMM) operators in two types of metalliferous mines in India, when they were engaged in the mining activity. Cross-comparison was done of the vibration dose value (VDV) for HEMM operators as well as each type of mine. The VDV for the shovel operator in bauxite mine was observed to be 13.53 +/- 5.63 m/s(7/4) with 25% of the readings higher than the prescribed limit whereas in iron ore mine VDV for dumper operator was 10.81 +/- 3.44 m/s(7/4) with 14.62% readings on the higher side. Cross-comparison of the VDV values for bauxite and iron ore mines revealed that it was 9.57 +/- 4.93 and 8.21 +/- 5.12 m/s(7/4) with 21.28 and 14.95% of the readings on the higher side respectively. The Student's t test level was found to be insignificant for both type of mines, indicating that the WBV exposure is not dependent on the type of mine but is dependent on the working condition and type of HEMM in operation.

Application and research of block caving in Pulang copper mine

NASA Astrophysics Data System (ADS)

Ge, Qifa; Fan, Wenlu; Zhu, Weigen; Chen, Xiaowei

2018-01-01

The application of block caving in mines shows significant advantages in large scale, low cost and high efficiency, thus block caving is worth promoting in the mines that meets the requirement of natural caving. Due to large scale of production and low ore grade in Pulang copper mine in China, comprehensive analysis and research were conducted on rock mechanics, mining sequence, undercutting and stability of bottom structure in terms of raising mine benefit and maximizing the recovery mineral resources. Finally this study summarizes that block caving is completely suitable for Pulang copper mine.

Linking geological and health sciences to assess childhood lead poisoning from artisanal gold mining in Nigeria.

PubMed

Plumlee, Geoffrey S; Durant, James T; Morman, Suzette A; Neri, Antonio; Wolf, Ruth E; Dooyema, Carrie A; Hageman, Philip L; Lowers, Heather A; Fernette, Gregory L; Meeker, Gregory P; Benzel, William M; Driscoll, Rhonda L; Berry, Cyrus J; Crock, James G; Goldstein, Harland L; Adams, Monique; Bartrem, Casey L; Tirima, Simba; Behbod, Behrooz; von Lindern, Ian; Brown, Mary Jean

2013-06-01

In 2010, Médecins Sans Frontières discovered a lead poisoning outbreak linked to artisanal gold processing in northwestern Nigeria. The outbreak has killed approximately 400 young children and affected thousands more. Our aim was to undertake an interdisciplinary geological- and health-science assessment to clarify lead sources and exposure pathways, identify additional toxicants of concern and populations at risk, and examine potential for similar lead poisoning globally. We applied diverse analytical methods to ore samples, soil and sweep samples from villages and family compounds, and plant foodstuff samples. Natural weathering of lead-rich gold ores before mining formed abundant, highly gastric-bioaccessible lead carbonates. The same fingerprint of lead minerals found in all sample types confirms that ore processing caused extreme contamination, with up to 185,000 ppm lead in soils/sweep samples and up to 145 ppm lead in plant foodstuffs. Incidental ingestion of soils via hand-to-mouth transmission and of dusts cleared from the respiratory tract is the dominant exposure pathway. Consumption of water and foodstuffs contaminated by the processing is likely lesser, but these are still significant exposure pathways. Although young children suffered the most immediate and severe consequences, results indicate that older children, adult workers, pregnant women, and breastfed infants are also at risk for lead poisoning. Mercury, arsenic, manganese, antimony, and crystalline silica exposures pose additional health threats. Results inform ongoing efforts in Nigeria to assess lead contamination and poisoning, treat victims, mitigate exposures, and remediate contamination. Ore deposit geology, pre-mining weathering, and burgeoning artisanal mining may combine to cause similar lead poisoning disasters elsewhere globally.

Linking Geological and Health Sciences to Assess Childhood Lead Poisoning from Artisanal Gold Mining in Nigeria

PubMed Central

Durant, James T.; Morman, Suzette A.; Neri, Antonio; Wolf, Ruth E.; Dooyema, Carrie A.; Hageman, Philip L.; Lowers, Heather A.; Fernette, Gregory L.; Meeker, Gregory P.; Benzel, William M.; Driscoll, Rhonda L.; Berry, Cyrus J.; Crock, James G.; Goldstein, Harland L.; Adams, Monique; Bartrem, Casey L.; Tirima, Simba; Behbod, Behrooz; von Lindern, Ian; Brown, Mary Jean

2013-01-01

Background: In 2010, Médecins Sans Frontières discovered a lead poisoning outbreak linked to artisanal gold processing in northwestern Nigeria. The outbreak has killed approximately 400 young children and affected thousands more. Objectives: Our aim was to undertake an interdisciplinary geological- and health-science assessment to clarify lead sources and exposure pathways, identify additional toxicants of concern and populations at risk, and examine potential for similar lead poisoning globally. Methods: We applied diverse analytical methods to ore samples, soil and sweep samples from villages and family compounds, and plant foodstuff samples. Results: Natural weathering of lead-rich gold ores before mining formed abundant, highly gastric-bioaccessible lead carbonates. The same fingerprint of lead minerals found in all sample types confirms that ore processing caused extreme contamination, with up to 185,000 ppm lead in soils/sweep samples and up to 145 ppm lead in plant foodstuffs. Incidental ingestion of soils via hand-to-mouth transmission and of dusts cleared from the respiratory tract is the dominant exposure pathway. Consumption of water and foodstuffs contaminated by the processing is likely lesser, but these are still significant exposure pathways. Although young children suffered the most immediate and severe consequences, results indicate that older children, adult workers, pregnant women, and breastfed infants are also at risk for lead poisoning. Mercury, arsenic, manganese, antimony, and crystalline silica exposures pose additional health threats. Conclusions: Results inform ongoing efforts in Nigeria to assess lead contamination and poisoning, treat victims, mitigate exposures, and remediate contamination. Ore deposit geology, pre-mining weathering, and burgeoning artisanal mining may combine to cause similar lead poisoning disasters elsewhere globally. PMID:23524139

Linking geology and health sciences to assess childhood lead poisoning from artisanal gold mining in Nigeria

USGS Publications Warehouse

Plumlee, Geoffrey S.; Durant, James T.; Morman, Suzette A.; Neri, Antonio; Wolf, Ruth E.; Dooyema, Carrie A.; Hageman, Philip L.; Lowers, Heather; Fernette, Gregory L.; Meeker, Gregory P.; Benzel, William M.; Driscoll, Rhonda L.; Berry, Cyrus J.; Crock, James G.; Goldstein, Harland L.; Adams, Monique; Bartrem, Casey L.; Tirima, Simba; Behrooz, Behbod; von Lindern, Ian; Brown, Mary Jean

2013-01-01

Background: In 2010, Médecins Sans Frontières discovered a lead poisoning outbreak linked to artisanal gold processing in northwestern Nigeria. The outbreak has killed approximately 400 young children and affected thousands more. Objectives: Our aim was to undertake an interdisciplinary geological- and health-science assessment to clarify lead sources and exposure pathways, identify additional toxicants of concern and populations at risk, and examine potential for similar lead poisoning globally. Methods: We applied diverse analytical methods to ore samples, soil and sweep samples from villages and family compounds, and plant foodstuff samples. Results: Natural weathering of lead-rich gold ores before mining formed abundant, highly gastric-bioaccessible lead carbonates. The same fingerprint of lead minerals found in all sample types confirms that ore processing caused extreme contamination, with up to 185,000 ppm lead in soils/sweep samples and up to 145 ppm lead in plant foodstuffs. Incidental ingestion of soils via hand-to-mouth transmission and of dusts cleared from the respiratory tract is the dominant exposure pathway. Consumption of water and foodstuffs contaminated by the processing is likely lesser, but these are still significant exposure pathways. Although young children suffered the most immediate and severe consequences, results indicate that older children, adult workers, pregnant women, and breastfed infants are also at risk for lead poisoning. Mercury, arsenic, manganese, antimony, and crystalline silica exposures pose additional health threats. Conclusions: Results inform ongoing efforts in Nigeria to assess lead contamination and poisoning, treat victims, mitigate exposures, and remediate contamination. Ore deposit geology, pre-mining weathering, and burgeoning artisanal mining may combine to cause similar lead poisoning disasters elsewhere globally.

Tourmaline in Appalachian - Caledonian massive sulphide deposits and its exploration significance.

USGS Publications Warehouse

Slack, J.F.

1982-01-01

Tourmaline is a common gangue mineral in several types of stratabound mineral deposits, including some massive base-metal sulphide ores of the Appalachian - Caledonian orogen. It is most abundant (sometimes forming massive foliated tourmalinite) in sediment-hosted deposits, such as those at the Elizabeth Cu mine and the Ore Knob Cu mine (North Carolina, USA). Trace amounts of tourmaline occur associated with volcanic-hosted deposits in the Piedmont and New England and also in the Trondheim district. Tourmaline associated with the massive sulphide deposits are Mg- rich dravites with major- and trace-element compositions significantly different from schorl. It is suggested that the necessary B was produced by submarine exhalative processes as a part of the same hydrothermal system that deposited the ores. An abundance of dravite in non-evaporitic terrains is believed to indicate proximity to former subaqueous fumarolic centres.-R.A.H.

Mercury from mineral deposits and potential environmental impact

USGS Publications Warehouse

Rytuba, J.J.

2003-01-01

Mercury deposits are globally distributed in 26 mercury mineral belts. Three types of mercury deposits occur in these belts: silica-carbonate, hot-spring, and Almaden. Mercury is also produced as a by-product from several types of gold-silver and massive sulfide deposits, which account for 5% of the world's production. Other types of mineral deposits can be enriched in mercury and mercury phases present are dependent on deposit type. During processing of mercury ores, secondary mercury phases form and accumulate in mine wastes. These phases are more soluble than cinnabar, the primary ore mineral, and cause mercury deposits to impact the environment more so than other types of ore deposits enriched in mercury. Release and transport of mercury from mine wastes occur primarily as mercury-enriched particles and colloids. Production from mercury deposits has decreased because of environmental concerns, but by-product production from other mercury-enriched mineral deposits remains important.

Alfred E. Bergeat (1866-1924): a distinguished volcanologist and ore deposit researching scientist at the mining academies of Freiberg (Saxony) and Clausthal (Harz mountains) in Germany

NASA Astrophysics Data System (ADS)

Pfaffl, Fritz A.

2010-06-01

Alfred E. Bergeat, originated from a family, who produced gold-glance in a factory (porcelain painting), studied mineralogy and geology at the University of Munich from 1886 to 1892. Due to the results of his habilitation work on the volcanism of island arcs, especially of the Stromboli volcanic island in the Tyrrhenian Sea, he became a recognized volcanologist and specialist in volcanic petrography. He further became an explorer of syngenetic, epigenetic and deuterogenic ore deposits at the mining academies (Bergakademien) of Freiberg (Saxony) and Clausthal (Harz mountains). He described these ore deposits in a two-volume manual (1904-1906) which was summarized again in 1913. After his early death in 1924, the two manuals “Die Vulkane” (1925) and “Vulkankunde” (1927) were posthumously published by his colleague and friend Karl Sapper (1866-1945).

Investigation of the environmental impacts of naturally occurring radionuclides in the processing of sulfide ores for gold using gamma spectrometry.

PubMed

Gbadago, J K; Faanhof, A; Darko, E O; Schandorf, C

2011-09-01

The possible environmental impacts of naturally occurring radionuclides on workers and a critical community, as a result of milling and processing sulfide ores for gold by a mining company at Bogoso in the western region of Ghana, have been investigated using gamma spectroscopy. Indicative doses for the workers during sulfide ore processing were calculated from the activity concentrations measured at both physical and chemical processing stages. The dose rate, annual effective dose equivalent, radium equivalent activity, external and internal hazard indices, and radioactivity level index for tailings, for the de-silted sediments of run-off from the vicinity of the tailings dam through the critical community, and for the soils of the critical community's basic schools were calculated and found to be lower than their respective permissible limits. The environmental impact of the radionuclides is therefore expected to be low in this mining environment.

Bioleaching of manganese by Aspergillus sp. isolated from mining deposits.

PubMed

Mohanty, Sansuta; Ghosh, Shreya; Nayak, Sanghamitra; Das, Alok Prasad

2017-04-01

A comprehensive study on fungus assisted bioleaching of manganese (Mn) was carried out to demonstrate Mn solubilization of collected low grade ore from mining deposits of Sanindipur, Odisha, India. A native fungal strain MSF 5 was isolated and identified as Aspergillus sp. by Inter Transcribed Spacer (ITS) sequencing. The identified strain revealed an elevated tolerance ability to Mn under varying optimizing conditions like initial pH (2, 3, 4, 5, 6, 7), carbon sources (dextrose, sucrose, fructose and glucose) and pulp density (2%, 3%, 4%, 5% and 6%). Bioleaching studies carried out under optimized conditions of 2% pulp density of Mn ore at pH 6, temperature 37 °C and carbon dosage (dextrose) resulted with 79% Mn recovery from the ore sample within 20 days. SEM-EDX characterization of the ore sample and leach residue was carried out and the micrographs demonstrated porous and coagulated precipitates scattered across the matrix. The corresponding approach of FTIR analysis regulating the Mn oxide formation shows a distinctive peak of mycelium cells with and without treated Mn, resulting with generalized vibrations like MnO x stretching and CH 2 stretch. Thus, our investigation endeavors' the considerate possible mechanism involved in fungal surface cells onto Mn ore illustrating an alteration in cellular Mn interaction. Copyright © 2016 Elsevier Ltd. All rights reserved.

Paragenetic and minor- and trace-element studies of Mississippi Valley-type ore deposits of the Silesian-Cracow district, Poland

USGS Publications Warehouse

Viets, J.G.; Leach, D.L.; Lichte, F.E.; Hopkins, R.T.; Gent, C.A.; Powell, J.W.

1996-01-01

Paragenetic and minor- and trace-element studies were conducted on samples of epigenetic ore and gangue minerals collected from mines and drill core in the Silesian-Cracow (S-C) district of southern Poland. Four discrete mineral suites representing four mineralizing stages can be identified throughout the district. The earliest epigenetic minerals deposited during stage 1 consist of a late dolomite cement together with minor pyrite and marcasite. Stage 2 was the first ore-forming stage and included repetitive deposition of sphalerite and galena in a variety of morphologies. Stage 3 abruptly followed the first ore stage and deposited marcasite and pyrite with variable amounts of late sphalerite and galena. In the samples studied, minerals deposited during stage 3 are predominately marcasite-pyrite with minor sphalerite and galena in the Pomorzany and Olkusz mines, whereas, at the Trzebionka mine, stage 3 mineralization deposited mostly galena and sphalerite with little marcasite or pyrite. Stage 4 minerals include contains barite, followed by calcite, with very minor pyrite and a rare, late granular sphalerite. Compared to other major Mississippi Valley-type (MVT) districts of the world, the Silesian-Cracow district contains sphalerite with the second largest range in Ag concentrations and the largest range in Fe and Cd concentrations of any district. Unlike in other districts, very wide ranges in minor- and trace-element concentrations are also observed in paragenetically equivalent samples collected throughout the district. This wide range indicates that the minor- and trace-element content of the ore-forming environment was highly variable, both spatially and temporally, and suggests that the hydrologic system that the ore fluids traversed from their basinal source was very complex. Throughout the district, a significant increase in Tl, Ge, and As concentrations is accompanied by a lightening of sulfur isotopes between stage 2 and stage 3 minerals. This change appears to record a major district-scale hydrologic event that probably reflects the introduction of fluids with significantly different geochemistry than that of earlier ore-forming fluids.

Tellurium, a guide to mineral deposits

USGS Publications Warehouse

Watterson, J.R.; Gott, G.B.; Neuerburg, G.J.; Lakin, H.W.; Cathrall, J.B.

1977-01-01

Te dispersion patterns are useful in exploring for different types of mineral deposits and in providing additional information about known ore deposits. The Te content of rocks is given for five mining districts in the western United States: Coeur d'Alene, Idaho; Robinson, near Ely, Nevada; Montezuma, Colorado; Crater Creek area, Colorado; Cripple Creek, Colorado. Many of the analyses were obtained by use of a new analytical method sensitive to 0.001 ppm Te. The principal ore deposits in the Coeur d'Alene district, Idaho, are Pb-Zn-Ag replacement veins in Precambrian rocks of the Belt Supergroup. Te dispersion patterns show the outlines of the original mineral belts, the effects of intrusive events, the location of ore deposits, the displacements caused by post-ore faulting, and the borders of the 780-km2 district. The disseminated porphyry Cu deposits of the Robinson mining district, Nevada, are associated with Cretaceous quartz monzonite stocks that have intruded Palaeozoic carbonate rocks. Te is present in rock samples in concentrations as high as 10,000 ppm and forms a halo around the areas containing the Cu deposits. The alteration zones in the porphyry Mo district near Montezuma, Colorado, are developed around several small Tertiary intrusions occurring along a regional shear zone. Te haloes reflect the locations of porphyry intrusives, individual deposits and their ore shoots, and the pattern and intensity of adjacent alteration. The Te content of soils over the Montezuma stock is higher than, and varies independently from, the Te content of adjacent outcrops. Soils generally contain more Te than adjacent outcropping rocks. Soil may collect gaseous Te compounds from mineral deposits. The Crater Creek area is a northwestern extension of the Summitville mining district, Colorado. Te dispersion patterns radiate out from exposed Cu-Pb-Zn veins, from an outcrop of molybdenite stockwork veins and from associated iron-stained altered rock. Te haloes intensify exponentially with proximity to known ore and suggest the presence of Summitville-type chimney deposits. Most of the gold- and silver-telluride ore in the Cripple Creek district, Colorado, is found in fracture fillings within a volcanic subsidence basin. Haloes of Au, Ag and Te all define the mineralized portions of the fissure veins. ?? 1977.

A reinterpretation of the δDH2O of inclusion fluids in contemporaneous quartz and sphalerite, Creede mining district, Colorodo: a generic problem for shallow orebodies?

USGS Publications Warehouse

Foley, Nora K.; Bethke, Philip M.; Rye, Robert O.

1989-01-01

The unusually high contrast between the salinities of the ore-depositing fluids and the ground water overlying the ore zone allowed recognition of this phenomenon at Creede. It is likely, however, that Creede is not unique. Similar phenomena may be common in shallow ore zones where rapid fluctuation of an interface between a deep, high-temperature thermal plume and an overlying, cooler ground water may be expected to occur. Careful study of the origins of fluid inclusions, particularly in quartz, is essential to characterize the primary ore fluids and to assess the role of ground water in the hydrology of shallow ore deposits.

THE USE OF INSITU TREATMENT TO REDUCE TOXICITY

EPA Science Inventory

Mining or smelting of lead and zinc ores generates mine tailing and smelter slags rich in lead, zinc, and cadmium. Old smelting operations have commonly caused severly contaminated sites and adverse effects in the terrestrial environment. Research has clarified the causes of s...

Fractional crystallization-induced variations in sulfides from the Noril’sk-Talnakh mining district (polar Siberia, Russia)

USGS Publications Warehouse

Duran, C.J.; Barnes, S-J.; Pleše, P.; Prašek, M. Kudrna; Zientek, Michael L.; Pagé, P.

2017-01-01

The distribution of platinum-group elements (PGE) within zoned magmatic ore bodies has been extensively studied and appears to be controlled by the partitioning behavior of the PGE during fractional crystallization of magmatic sulfide liquids. However, other chalcophile elements, especially TABS (Te, As, Bi, Sb, and Sn) have been neglected despite their critical role in forming platinum-group minerals (PGM). TABS are volatile trace elements that are considered to be mobile so investigating their primary distribution may be challenging in magmatic ore bodies that have been somewhat altered. Magmatic sulfide ore bodies from the Noril’sk-Talnakh mining district (polar Siberia, Russia) offer an exceptional opportunity to investigate the behavior of TABS during fractional crystallization of sulfide liquids and PGM formation as the primary features of the ore bodies have been relatively well preserved. In this study, new petrographic (2D and 3D) and whole-rock geochemical data from Cu-poor to Cu-rich sulfide ores of the Noril’sk-Talnakh mining district are integrated with published data to consider the role of fractional crystallization in generating mineralogical and geochemical variations across the different ore types (disseminated to massive). Despite textural variations in Cu-rich massive sulfides (lenses, veins, and breccias), these sulfides have similar chemical compositions, which suggests that Cu-rich veins and breccias formed from fractionated sulfide liquids that were injected into the surrounding rocks. Numerical modeling using the median disseminated sulfide composition as the initial sulfide liquid composition and recent DMSS/liq and DISS/liq predicts the compositional variations observed in the massive sulfides, especially in terms of Pt, Pd, and TABS. Therefore, distribution of these elements in the massive sulfides was likely controlled by their partitioning behavior during sulfide liquid fractional crystallization, prior to PGM formation. Our observations indicate that in the Cu-poor massive sulfides the PGM formed as the result of exsolution from sulfide minerals whereas in the Cu-rich massive sulfides the PGM formed by crystallization from late-stage fractionated sulfide liquids. We suggest that the significant amount of Sn-bearing PGM may be related to crustal contamination from granodiorite, whereas As, Bi, Te, and Sb were likely added to the magma along with S from sedimentary rocks. Large PGM that are scarce and randomly distributed may account for most of the whole-rock Pt budget. Based on our results, we propose a holistic genetic model for the formation of the magmatic sulfide ore bodies of the Noril’sk-Talnakh mining district.

Alpha emitting radionuclides in drainage from Quinta do Bispo and Cunha Baixa uranium mines (Portugal) and associated radiotoxicological risk.

PubMed

Carvalho, Fernando P; Oliveira, João M; Faria, Isabel

2009-11-01

Two large uranium mines, Quinta do Bispo and Cunha Baixa, district of Viseu, North of Portugal, were exploited until 1991. Sulfuric acid was used for in situ uranium leaching in Cunha Baixa mine and for heap leaching of low grade ores at both mines. Large amounts of mining and milling residues were accumulated nearby. Since closure of mines, the treatment of acid mine waters has been maintained and treated water is released into surface water lines. Analysis of radionuclides in the soluble phase and in the suspended matter of water samples from the uranium mines, from the creeks receiving the discharges of mine effluents, from the rivers and from wells in this area, show an enhancement of radioactivity levels. For example, downstream the discharge of mine effluents into Castelo Stream, the concentrations of dissolved uranium isotopes and uranium daughters were up to 14 times the concentrations measured upstream; (238)U concentration in suspended particulate matter of Castelo Stream reached 72 kBq kg(-1), which is about 170 times higher than background concentrations in Mondego River. Nevertheless, radionuclide concentrations decreased rapidly to near background values within a distance of about 7 kilometers from the discharge point. Enhancement of radioactivity in underground waters was positively correlated with a decrease in water pH and with an increase of sulfate ion concentration, pointing out to Cunha Baixa mine as the source of groundwater contamination. The radiotoxic exposure risk arising from using these well waters as drinking water and as irrigation water is discussed and implementation of environmental remediation measures is advised.

Children's personal exposure to PM10 and associated metals in urban, rural and mining activity areas.

PubMed

Hinwood, Andrea; Callan, Anna C; Heyworth, Jane; McCafferty, Peter; Sly, Peter D

2014-08-01

There has been limited study of children's personal exposure to PM10 and associated metals in rural and iron ore mining activity areas where PM10 concentrations can be very high. We undertook a small study of 70 children where 13 children were recruited in an area of iron ore mining processing and shipping, 15 children from an area in the same region with no mining activities, and 42 children in an urban area. Each child provided a 24h personal exposure PM10 sample, a first morning void urine sample, a hair sample, time activity diary, and self administered questionnaire. Children's 24h personal PM10 concentrations were low (median of 28 μg m(-3) in the mining area; 48 μg m(-3) in the rural area and 45 μg m(-3) in the urban area) with corresponding outdoor PM10 concentrations also low. Some very high personal PM10 concentrations were recorded for individuals (>300 μg m(-3)) with the highest concentrations recorded in the mining and rural areas in the dry season. PM10 concentrations were highly variable. Hair aluminium, cadmium and manganese concentrations were higher in the iron ore activity area, while hair mercury, copper and nickel concentrations were higher in the urban area. Factors such as season and ventilation appear to be important but this study lacked power to confirm this. These results need to be confirmed by a larger study and the potential for absorption of the metals needs to be established along with the factors that increase exposures and the potential for health risks arising from exposure. Copyright © 2014 Elsevier Ltd. All rights reserved.

Land Ecological Security Evaluation of Underground Iron Mine Based on PSR Model

NASA Astrophysics Data System (ADS)

Xiao, Xiao; Chen, Yong; Ruan, Jinghua; Hong, Qiang; Gan, Yong

2018-01-01

Iron ore mine provides an important strategic resource to the national economy while it also causes many serious ecological problems to the environment. The study summed up the characteristics of ecological environment problems of underground iron mine. Considering the mining process of underground iron mine, we analysis connections between mining production, resource, environment and economical background. The paper proposed a land ecological security evaluation system and method of underground iron mine based on Pressure-State-Response model. Our application in Chengchao iron mine proves its efficiency and promising guide on land ecological security evaluation.

A risk assessment for exposure to grunerite asbestos (amosite) in an iron ore mine

PubMed Central

Nolan, R. P.; Langer, A. M.; Wilson, Richard

1999-01-01

The potential for health risks to humans exposed to the asbestos minerals continues to be a public health concern. Although the production and use of the commercial amphibole asbestos minerals—grunerite (amosite) and riebeckite (crocidolite)—have been almost completely eliminated from world commerce, special opportunities for potentially significant exposures remain. Commercially viable deposits of grunerite asbestos are very rare, but it can occur as a gangue mineral in a limited part of a mine otherwise thought asbestos-free. This report describes such a situation, in which a very localized seam of grunerite asbestos was identified in an iron ore mine. The geological occurrence of the seam in the ore body is described, as well as the mineralogical character of the grunerite asbestos. The most relevant epidemiological studies of workers exposed to grunerite asbestos are used to gauge the hazards associated with the inhalation of this fibrous mineral. Both analytical transmission electron microscopy and phase-contrast optical microscopy were used to quantify the fibers present in the air during mining in the area with outcroppings of grunerite asbestos. Analytical transmission electron microscopy and continuous-scan x-ray diffraction were used to determine the type of asbestos fiber present. Knowing the level of the miner’s exposures, we carried out a risk assessment by using a model developed for the Environmental Protection Agency. PMID:10097051

Mercury dispersion in soils of an abandoned lead-zinc-silver mine, San Quintín (Spain)

NASA Astrophysics Data System (ADS)

Esbrí, José Maria; Martín-Crespo, T.; Gómez-Ortiz, D.; Monescillo, C. I.; Lorenzo, S.; Higueras, P.

2010-05-01

The mine considered on this work, namely San Quintín, is a filonian field with hydrothermal ores exploited during almost fifty years (1887-1934), producing 550.000Tm of galena, 550Tm of silver and 5.000 of sphalerite. Some rewashing works of tailings muds was achieved in recent times (1973-1985), including flotation tests of cinnabar ore from Almadén mines. The main problems remaining on the site are an active acid mine drainage (with pH ~ 2) and heavy metal dispersion on soils including gaseous mercury emissions. We present here results of a survey including soils sampling with mercury analysis and other pedological parameters, as well as determinations of mercury inmission in the atmosphere, using a common sampling grid. Analysis of soils samples has been carried out using an atomic absorption spectrometer AMA254, while air determinations were made by the same technique, using a Lumex RA-915+. The maps have been obtained by means of SURFER 8 software, as well as by ArcGIS software, and puts forward dispersion of mercury from cinnabar ore dump (108 ?g×g-1) to nearby soils (0.3 ?g×g-1 at 700 m of distance). The dispersion of mercury vapor exceed WHO level for chronic exposure (200 ng×m-3) in a small area (250 meters from cinnabar dump).

The Use of Traditional Hydrologic Field Techniques as a Means of Quantifying Mine-Related Contamination Impacts on a Surface Water Body, Norrbotten County, Sweden

NASA Astrophysics Data System (ADS)

Little, S. F. B.; Walder, I. F.; Cadol, D. D.

2016-12-01

The Malmberget/Vitåfors mining facility, located in Norrbotten County, Sweden, is the world's second largest underground iron ore mine, comprised of roughly 20 steeply dipping magnetite-hematite ore lenses, with an underground area of approximately 5 x 2.5km. Since its' opening in 1892, over 350Mt of ore have been removed from Malmberget, and another 350Mt of iron reserves have been declared proven and probable. The state-owned mining company, LKAB, operates the facility. They have increased production in the past years, effectively doubling the amount of ore processed annually, between 1998 and 2013. Despite these changes, the volume of water used within the system has not grown proportionally, and is not predicted to do so in the future. This is due to increases in process-water recycling, adding to the demands placed on this water. As it is reused, the conservative and trace element concentrations grow, affecting overall water quality. Some portion of the spent process water is released on a daily basis into the nearby Lina River. This discharge is generated in two ways: (1) By means of monitored release via outlet pipes, and (2) through diffuse leakage and subsurface flow originating at the facility's tailings and settling ponds. This study aims to describe both the quality and quantity of the second form of discharge- with the ultimate goal of predicting these attributes given projected ore processing and water-recycling increases. With limited data- consisting primarily of routine water sampling- an understanding of the nature of this leakage must be gained through combined geochemical modeling and site characterization. With this objective in mind, fieldwork was conducted to quantify the volume of flow between groundwater and surface water bodies in the portion of the river adjacent to the mine. This utilized two basic hydrologic techniques: stream gaging, and the deployment of simple seepage meters. The data collected from this investigation was then used to construct a hydrologic model illustrating the proposed movement of water from the tailings and settling ponds- chronicling the path to its eventual release into the gaining river. Further coupling of the hydrologic and geochemical information will improve the accuracy of this prediction, in addition to addressing the question of water quality.

19. DETAIL OF STAMP BATTERY AUTOMATIC FEEDER, LOOKING EAST. THIS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. DETAIL OF STAMP BATTERY AUTOMATIC FEEDER, LOOKING EAST. THIS IS THE MIDDLE OF THREE FEEDERS, ONE FOR EACH STAMP BATTERY. THE CHUTE (UPPER RIGHT) INTRODUCED THE CRUSHED ORE FROM THE ORE BIN. FLOW WAS CONTROLLED BY A SLIDING DOOR ON THE UPPER LEVEL. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

Life-Cycle environmental impact assessment of mineral industries

NASA Astrophysics Data System (ADS)

Hisan Farjana, Shahjadi; Huda, Nazmul; Parvez Mahmud, M. A.

2018-05-01

Mining is the extraction and processing of valuable ferro and non-ferro metals and minerals to be further used in manufacturing industries. Valuable metals and minerals are extracted from the geological deposits and ores deep in the surface through complex manufacturing technologies. The extraction and processing of mining industries involve particle emission to air or water, toxicity to the environment, contamination of water resources, ozone layer depletion and most importantly decay of human health. Despite all these negative impacts towards sustainability, mining industries are working throughout the world to facilitate the employment sector, economy and technological growth. The five most important miners in the world are South Africa, Russia, Australia, Ukraine, Guinea. The mining industries contributes to their GDP significantly. However, the most important issue is making the mining world sustainable thus reducing the emissions. To address the environmental impacts caused by the mining sectors, this paper is going to analyse the environmental impacts caused by the 5 major minerals extraction processes, which are bauxite, ilmenite, iron ore, rutile and uranium by using the life-cycle impact assessment technologies. The analysis is done here using SimaPro software version 8.4 using ReCipe, CML and Australian indicator method.

Geology Exchange Program

NASA Astrophysics Data System (ADS)

Because geology professors cannot bring ore deposits from around the globe into their classrooms, the next best thing is to take their students to the deposits, according to David Norman, an associate professor of geochemistry at New Mexico Tech and Angus Moore of the Royal School of Mines. They organized a new exchange program between the New Mexico Institute of Mining and Technology in Socorro, N.M., and the Royal School of Mines in London, England. In May, 14 students from England toured deposits in New Mexico, Arizona, Utah, and Colorado; in the photograph, Norman (on the right) describes a rock from a New Mexico ore deposit to some of the visitors from England. In early June a contingency from New Mexico Tech began studying deposits in England, Spain, and Portugal. Norman and Moore say that the exchange program may be expanded next year.

30 CFR 56.19000 - Application.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Application. 56.19000 Section 56.19000 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... handling ore, rock, and materials, the appropriate standards should be applied. (b) Standards 56.19021...

30 CFR 56.19000 - Application.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Application. 56.19000 Section 56.19000 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... handling ore, rock, and materials, the appropriate standards should be applied. (b) Standards 56.19021...

30 CFR 56.19000 - Application.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Application. 56.19000 Section 56.19000 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... handling ore, rock, and materials, the appropriate standards should be applied. (b) Standards 56.19021...

30 CFR 57.19000 - Application.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Application. 57.19000 Section 57.19000 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... handling ore, rock, and materials, the appropriate standards should be applied. (b) Standards 57.19021...

30 CFR 56.19000 - Application.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Application. 56.19000 Section 56.19000 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... handling ore, rock, and materials, the appropriate standards should be applied. (b) Standards 56.19021...

30 CFR 56.19000 - Application.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Application. 56.19000 Section 56.19000 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... handling ore, rock, and materials, the appropriate standards should be applied. (b) Standards 56.19021...

40 CFR 440.145-440.147 - [Reserved

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false [Reserved] 440.145-440.147 Section 440.145-440.147 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine Subcategory...

40 CFR 440.145-440.147 - [Reserved

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false [Reserved] 440.145-440.147 Section 440.145-440.147 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine Subcategory...

40 CFR 440.145-440.147 - [Reserved

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false [Reserved] 440.145-440.147 Section 440.145-440.147 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine Subcategory...

78 FR 7815 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Gamma...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-04

... Labor (DOL) is submitting the Mine Safety and Health Administration (MSHA) sponsored information.... This requirement protects the health of workers in mines with radioactive ores. This information... DEPARTMENT OF LABOR Office of the Secretary Agency Information Collection Activities; Submission...

Geological controls on refractory ore in an orogenic gold deposit, Macraes mine, New Zealand

NASA Astrophysics Data System (ADS)

Petrie, B. S.; Craw, D.; Ryan, C. G.

2005-07-01

The Macraes mine is hosted in an orogenic (mesothermal) gold deposit in metasedimentary rocks of the Otago Schist belt. Much gold occurs within altered schist with minimal silica-addition, and this study focuses on altered schist ore types. The unmineralized host schists are chemically and mineralogically uniform in composition, but include two end-member rock types: feldspathic schist and micaceous schist. Both rock types have undergone hydrothermal alteration along a shallow-dipping foliation-parallel shear zone, but their different rheological properties have affected the style of mineralisation. Micaceous schist has been extensively recrystallized and hydrothermally altered during ductile deformation, to form ores characterized by abundant, disseminated millimetre-scale pyrite cubes (typically 1 2 wt% S) and minor silicification. The earliest pyrite contained Ni and/or As in solid solution and no gold was imaged in these pyrites or later arsenopyrite grains. The ore type is refractory and gold recovery by cyanide leaching is less than 50%, with lowest recovery in rocks that have been less affected by later brittle deformation. In contrast, hydrothermally altered feldspathic schist is characterized by mineralised black microshears and veinlets formed during shear-zone related brittle deformation. Microsheared ore has relatively low sulphur content (<0.7 wt%) and muscovite has been illitised during hydrothermal alteration. Pyrite and arsenopyrite in microshears are fractured and deformed, and contain 1 10 μm blebs of gold. Later pyrite veinlets also contain micron- to submicron-scale inclusions of sphalerite, chalcopyrite, galena, and gold (≤10 microns). Gold in microsheared ore is more readily recoverable than in the refractory ore, although encapsulation of the fine gold grains inhibits cyanidation. Both microsheared ore and disseminated pyritic ore pass laterally into mineralised black shears, which contain hydrothermal graphite and late-stage cataclastic sulphides. This black, sheared ore releases gold readily, but the gold is then adsorbed on to gangue minerals (preg-robbed) and net cyanidation recovery can be less than 50%. Hence, low gold recovery during cyanidation results from (1) poor liberation of gold encapsulated in microcrystalline quartz and unfractured sulphide grains, and (2) preg-robbing of liberated gold during cyanidation. Introduction of pressure-oxidation of ore prior to cynidation has mitigated these issues.

Trace elements in seep waters along Whitewood Creek, South Dakota, and their toxicity to fathead minnows

USGS Publications Warehouse

Hamilton, S.J.; Buhl, K.J.

2000-01-01

Whitewood Creek, located in the Black Hills of southwestern South Dakota, has a long history of contamination from mining activity. Gold exploration began in the 1870s, and has continued since that time. Whitewood Creek received direct releases of tailings from 1870 to 1977 from Gold Run Creek in Lead, SD. It has been estimated that approximately 100 million to 1 billion tons of mining, milling, and ore processing wastes have been released by mining activity in the last century in to Whitewood Creek, the Belle Fourche river, and the Cheyenne River (Fox Consultants, Inc. 1984). Tailings deposition has altered the geomorphology of Whitewood Creek, and deposits up to 4.6 m. deep, have become stabilized by vegetation. Several other streams in the Black Hills also have been adversely affected by mining operations (Rahn 1996).As water leaches through rock strata that are disturbed by surface and subsurface mining, it dissolves inorganic elements and carries them to the groundwater.  Groundwater movement through the extensive tailings deposits in the Whitewood Creek valley enter the creek at various seeps along its downstream course to the Belle Fourche river, and the Belle Fourche River itself, which empties into the Cheyenne River and eventually into Lake Oahe.

Disposal and improvement of contaminated by waste extraction of copper mining in chile

NASA Astrophysics Data System (ADS)

Naranjo Lamilla, Pedro; Blanco Fernández, David; Díaz González, Marcos; Robles Castillo, Marcelo; Decinti Weiss, Alejandra; Tapia Alvarez, Carolina; Pardo Fabregat, Francisco; Vidal, Manuel Miguel Jordan; Bech, Jaume; Roca, Nuria

2016-04-01

This project originated from the need of a mining company, which mines and processes copper ore. High purity copper is produced with an annual production of 1,113,928 tons of concentrate to a law of 32%. This mining company has generated several illegal landfills and has been forced by the government to make a management center Industrial Solid Waste (ISW). The forecast volume of waste generated is 20,000 tons / year. Chemical analysis established that the studied soil has a high copper content, caused by nature or from the spread of contaminants from mining activities. Moreover, in some sectors, soil contamination by mercury, hydrocarbons and oils and fats were detected, likely associated with the accumulation of waste. The waters are also impacted by mining industrial tasks, specifically copper ores, molybdenum, manganese, sulfates and have an acidic pH. The ISW management center dispels the pollution of soil and water and concentrating all activities in a technically suitable place. In this center the necessary guidelines for the treatment and disposal of soil contamination caused by uncontrolled landfills are given, also generating a leachate collection system and a network of fluid monitoring physicochemical water quality and soil environment. Keywords: Industrial solid waste, soil contamination, Mining waste

Risk Assessment of Heavy Metal Pollution in Soils of Gejiu Tin Ore and Other Metal Deposits of Yunnan Province

NASA Astrophysics Data System (ADS)

Yang, Shuran; Danek, Tomas; Cheng, Xianfeng; Huang, Qianrui

2017-12-01

This paper aims to study three main metal mining areas in Yunnan Province, to summarize and analyze the heavy metal pollution situation in each mining area, and to assess the ecological risk of the mining areas. The results showed that heavy metal pollution existed in different regions of the three mining areas with pollution elements of Cd, As, Cu, Pb, Zn. Risk level, besides Zhen Yuan mining area (class C), for the other two areas was class D, with Beichang mining area in Lanping as the most serious polluted mining area.

Heavy metal pollution caused by small-scale metal ore mining activities: A case study from a polymetallic mine in South China.

PubMed

Sun, Zehang; Xie, Xiande; Wang, Ping; Hu, Yuanan; Cheng, Hefa

2018-10-15

Although metal ore mining activities are well known as an important source of heavy metals, soil pollution caused by small-scale mining activities has long been overlooked. This study investigated the pollution of surface soils in an area surrounding a recently abandoned small-scale polymetallic mining district in Guangdong province of south China. A total of 13 tailing samples, 145 surface soil samples, and 29 water samples were collected, and the concentrations of major heavy metals, including Cr, Mn, Co, Ni, Cu, Zn, As, Cd, Pb, and Se, were determined. The results show that the tailings contained high levels of heavy metals, with Cu, Zn, As, Cd, and Pb occurring in the ranges of 739-4.15 × 10 3 , 1.81 × 10 3 -5.00 × 10 3 , 118-1.26 × 10 3 , 8.14-57.7, and 1.23 × 10 3 -6.99 × 10 3  mg/kg, respectively. Heavy metals also occurred at high concentrations in the mine drainages (15.4-17.9 mg/L for Cu, 21.1-29.3 mg/L for Zn, 0.553-0.770 mg/L for Cd, and 1.17-2.57 mg/L for Pb), particularly those with pH below 3. The mean contents of Cu, Zn, As, Cd, and Pb in the surface soils of local farmlands were up to 7 times higher than the corresponding background values, and results of multivariate statistical analysis clearly indicate that Cu, Zn, Cd, and Pb were largely contributed by the mining activities. The surface soils from farmlands surrounding the mining district were moderately to seriously polluted, while the potential ecological risk of heavy metal pollution was extremely high. It was estimated that the input fluxes from the mining district to the surrounding farmlands were approximately 17.1, 59.2, 0.311, and 93.8 kg/ha/yr for Cu, Zn, Cd, and Pb, respectively, which probably occurred through transport of fine tailings by wind and runoff, and mine drainage as well. These findings indicate the significant need for proper containment of the mine tailings at small-scale metal ore mines. Copyright © 2018. Published by Elsevier B.V.

30 CFR 281.31 - Overriding royalties.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false Overriding royalties. 281.31 Section 281.31 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF THE... a producing mine, or to make possible the mining of economically marginal or low-grade ore deposits...

30 CFR 57.5047 - Gamma radiation surveys.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Gamma radiation surveys. 57.5047 Section 57... radiation surveys. (a) Gamma radiation surveys shall be conducted annually in all underground mines where radioactive ores are mined. (b) Surveys shall be in accordance with American National Standards (ANSI...

30 CFR 57.5047 - Gamma radiation surveys.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Gamma radiation surveys. 57.5047 Section 57... radiation surveys. (a) Gamma radiation surveys shall be conducted annually in all underground mines where radioactive ores are mined. (b) Surveys shall be in accordance with American National Standards (ANSI...

30 CFR 57.5047 - Gamma radiation surveys.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Gamma radiation surveys. 57.5047 Section 57... radiation surveys. (a) Gamma radiation surveys shall be conducted annually in all underground mines where radioactive ores are mined. (b) Surveys shall be in accordance with American National Standards (ANSI...

Translations on North Korea, Number 573.

DTIC Science & Technology

1978-02-02

Production 61 Ore Production 61 Changsong Mine 61 - c - KIM IL-SONG PHOTOS APPEARING IN ’NODONG SINMUN,’ DECEMBER 1977 [Editorial Report] The...Pyongyang Domestic Service in Korean 0800 GMT 12 Jan 78 SK] CHANGSONG MINE—The Changsong mine has overfulfilled the tagets set for tunneling by 270

Uranium deposits at the Jomac mine, White Canyon area, San Juan County, Utah

USGS Publications Warehouse

Trites, A.F.; Hadd, G.A.

1955-01-01

azurite, and chalcanthite occur locally with the uranium minerals. Principal ore guides at the Jomac mine are channels, and scours at the bottom of these channels coal-bearing sandstone or conglomerate at the base of the Shinarump conglomerate, coal, and jarosite.

40 CFR 440.145-440.147 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 440.145-440.147 Section 440.145-440.147 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine Subcategory §§ 440.145...

40 CFR 440.145-440.147 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 440.145-440.147 Section 440.145-440.147 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Gold Placer Mine Subcategory §§ 440.145...

Ferruginous compounds in the airborne particulate matter of the metropolitan area of Belo Horizonte, Minas Gerais, Brazil.

PubMed

Tavares, Fernanda Vasconcelos Fonseca; Ardisson, José Domingos; Rodrigues, Paulo César Horta; Fabris, José Domingos; Fernandez-Outon, Luis Eugenio; Feliciano, Vanusa Maria Delage

2017-08-01

Samples of soil, iron ore, and airborne particulate matter (size <10 μm) were analyzed with the main goal of investigating the differentiating physicochemical properties of their ferruginous compounds. These data were used to identify whether the sources of airborne particulate matter in the metropolitan area of Belo Horizonte, Minas Gerais, Brazil, are either from natural origin, as, for instance, re-suspension of particles from soil, or due to anthropogenic activities, meaning that it would be originated from the many iron ore minings surrounding the metropolitan area. Numerical simulations were used to model the atmospheric dispersion of the airborne particulate matter emitted by iron mining located at the Iron Quadrangle geodomain, Minas Gerais. Results from these numerical simulations supported identifying the sites with the highest concentrations of airborne particulate matter in the metropolitan area. Samples of these suspended materials were collected at the selected sites by using high-volume air samplers. The physicochemical features of the solid materials were assessed by X-ray fluorescence, X-ray diffraction, magnetometry, and 57 Fe Mössbauer spectroscopy. The soil materials were found to be rich in quartz, aluminum, organic matter, and low contents of iron, mainly as low crystalline iron oxides. The samples of the iron ores, on the other hand, contain high concentration of iron, dominantly as relatively pure and crystalline hematite (α-Fe 2 O 3 ). The samples of the airborne particulate matter are rich in iron, mainly as hematite, but contained also quartz, aluminum, and calcium. Mössbauer spectroscopy was used to evaluate the hyperfine structure of 57 Fe of the hematite both from the iron ore and the soil samples. The structural characteristics of the hematite of these particulate materials were further explored. The direct influence of the iron ore mining on the composition of the airborne particulate matter was clearly evidenced based on the trace ability of hematite to its source of emission. Even the atmospheric air on regions relatively far away from the mining activities is also significantly influenced.

Ultrafine particles derived from mineral processing: A case study of the Pb-Zn sulfide ore with emphasis on lead-bearing colloids.

PubMed

Mikhlin, Yuri; Vorobyev, Sergey; Romanchenko, Alexander; Karasev, Sergey; Karacharov, Anton; Zharkov, Sergey

2016-03-01

Although mining and mineral processing industry is a vast source of heavy metal pollutants, the formation and behavior of micrometer- and nanometer-sized particles and their aqueous colloids entered the environment from the technological media has received insufficient attention to date. Here, the yield and characteristics of ultrafine mineral entities produced by routine grinding of the Pb-Zn sulfide ore (Gorevskoe ore deposit, Russia) were studied using laser diffraction analysis (LDA), dynamic light scattering (DLS) and zeta potential measurement, microscopy, X-ray photoelectron spectroscopy, with most attention given to toxic lead species. It was revealed, in particular, that the fraction of particles less that 1 μm in the ground ore typical reaches 0.4 vol. %. The aquatic particles in supernatants were micrometer size aggregates with increased content of zinc, sulfur, calcium as compared with the bulk ore concentrations. The hydrodynamic diameter of the colloidal species decreased with time, with their zeta potentials remaining about -12 mV. The colloids produced from galena were composed of 20-50 nm PbS nanoparticles associated with lead sulfate and thiosulfate, while the surface oxidation products at precipitated galena were largely lead oxyhydroxides. The size and zeta potential of the lead-bearing colloids decreased with time down to about 100 nm and from -15 mV to -30 mV, respectively. And, conversely, lead sulfide nanoparticles were mobilized before the aggregates during redispersion of the precipitates in fresh portions of water. The potential environmental impact of the metal-bearing colloids, which is due to the large-scale production and relative stability, is discussed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mercury and methylmercury contents in mine-waste calcine, water, and sediment collected from the Palawan Quicksilver mine, Philippines

USGS Publications Warehouse

Gray, J.E.; Greaves, I.A.; Bustos, D.M.; Krabbenhoft, D.P.

2003-01-01

The Palawan Quicksilver mine, Philippines, produced about 2,900 t of mercury during mining of cinnabar ore from 1953 to 1976. More than 2,000,000 t of mine-waste calcines (retorted ore) were produced during mining, much of which were used to construct a jetty in nearby Honda Bay. Since 1995, high Hg contents have been found in several people living near the mine, and 21 of these people were treated for mercury poisoning. Samples of mine-waste calcine contain high total Hg concentrations ranging from 43-660 ??g/g, whereas total Hg concentrations in sediment samples collected from a mine pit lake and local stream vary from 3.7-400 ??g/g. Mine water flowing through the calcines is acidic, pH 3.1-4.3, and total Hg concentrations ranging from 18-31 ??g/l in this water significantly exceed the 1.0-??g/l drinking water standard for Hg recommended by the World Health Organization (WHO). Total Hg contents are generally lower in water samples collected from surrounding domestic wells, the mine pit lake, Honda Bay, and the nearby stream, varying from 0.008-1.4 ??g/l. Methylmercury concentrations in water draining mine calcines range from <0.02-1.4 ng/l, but methylmercury is highest in the pit lake water, ranging from 1.7-3.1 ng/l. Mercury methylation at the Palawan mine is similar to or higher than that found in other mercury mines worldwide. Much of the methylmercury generated in Palawan mine-waste calcines and those in Honda Bay is transferred to water, and then to marine fish and seafood. A food source pathway of Hg to humans is most likely in this coastal, high fish-consuming population.

The Effect of Initial Irrigation Conditions on Heap Leaching Efficiency

NASA Astrophysics Data System (ADS)

Briseño Arellano, A. D.; Milczarek, M.; Yao, M.; Brusseau, M. L. L.

2017-12-01

Heap leaching is an unsaturated flow metal recovery process, in which mined ore is irrigated with a lixiviant to dissolve metal contained in the ore. The metal is then extracted from solution. Large scale operations involve stacking ore to depths of 6 to 18 meters on pads that may be hundreds of hectares in area. Heterogeneities within the stacked ore can lead to uneven wetting and the formation of preferential flow pathways, which reduces solution contact and lowers metal recovery. Furthermore, mineral dissolution can cause alteration of the porous media structure and loss of ore permeability. Many mine operators believe that slow initial irrigation rates help minimize permeability loss and increase metal recovery rates. However, this phenomenon has not been studied in detail. Experiments were conducted to investigate the effect of varying initial irrigation rates on leach ore stability. These were conducted with large columns (1.5 m high, 0.5 m in diameter) packed with crushed ore samples that are known to have permeability constraints. The columns were highly instrumented to assess potential changes in material properties both spatially and temporally. Water content was measured with three different methods: capacitance soil moisture sensors placed at 20-cm intervals; a neutron probe to periodically log every 30 cm from four different directions; and electrical resistivity sensors to create a 2-dimensional tomography profile of water content over time. Tensiometers were paired with the soil moisture sensors to measure matric suction and characterize moisture retention characteristics. A non-reactive tracer was used to characterize advective-dispersive transport under unsaturated conditions. A dye solution was introduced at the end of each experiment to map preferential pathways. Continuous monitoring of settling at the surface assisted in measuring consolidation and loss in permeability.